LAMPF experimental-area beam current monitors

International Nuclear Information System (INIS)

Tallerico, P.J.

1975-01-01

This paper summarizes the design and operational performance of a wide- range current monitor system used to measure charged-particle currents in the experimental areas of the Clinton P. Anderson Meson Physics Facility (LAMPF), a proton accelerator. The major features of the system are high sensitivity, wide dynamic range, and the ability to withstand high levels of radiation. The current pulses detected are from 50 μs to 1 ms in duration at repetition rates of from 1 to 120 Hz. The pulse amplitude varies from 1 μA to 17 mA of protons or H - ions. Both real-time and integrated outputs are available, and the minimum detectable currents are 1 μA at the video output and 50 nA at the integrated output. The basic system is comprised of toroids, preamplifiers, signal conditioners, voltage-to-frequency converters, and digital accumulators. The entire system is spread out over 1 km of beam pipe. Provision is made for calibration and for sending the outputs to remote users. The system is normally controlled by a small digital computer, which allows the system to be quite flexible in operation. The design features of the toroids and the associated electronics are discussed in detail, with emphasis on the steps taken to reduce noise and make the toroids temperature and radiation resistant

75 FR 65710 - Current Value of Funds Rate

Science.gov (United States)

2010-10-26

... percentage rate to be used in assessing interest charges for outstanding debts owed to the Government... DEPARTMENT OF THE TREASURY Fiscal Service Current Value of Funds Rate AGENCY: Financial Management Service, Fiscal Service, Treasury. ACTION: Notice of rate for use in Federal debt collection and discount...

Disruptions in large value payment systems: an experimental approach

NARCIS (Netherlands)

Abbink, K.; Bosman, R.; Heijmans, R.; van Winden, F.

2010-01-01

This experimental study investigates the behaviour of banks in a large value payment system. More specifically,we look at 1) the reactions of banks to disruptions in the payment system, 2) the way in which the history of disruptions affects the behaviour of banks (path dependency) and 3) the effect

Disruptions in large value payment systems: An experimental approach

NARCIS (Netherlands)

Abbink, K.; Bosman, R.; Heijmans, R.; van Winden, F.; Hellqvist, M.; Laine, T.

2012-01-01

This experimental study investigates the behaviour of banks in a large value payment system. More specifically, we look at 1) the reactions of banks to disruptions in the payment system, 2) the way in which the history of disruptions affects the behaviour of banks (path dependency) and 3) the effect

Experimental modeling of eddy current inspection capabilities

International Nuclear Information System (INIS)

Junker, W.R.; Clark, W.G.

1984-01-01

This chapter examines the experimental modeling of eddy current inspection capabilities based upon the use of liquid mercury samples designed to represent metal components containing discontinuities. A brief summary of past work with mercury modeling and a detailed discussion of recent experiments designed to further evaluate the technique are presented. The main disadvantages of the mercury modeling concept are that mercury is toxic and must be handled carefully, liquid mercury can only be used to represent nonferromagnetic materials, and wetting and meniscus problems can distort the effective size of artificial discontinuities. Artificial discontinuities placed in a liquid mercury sample can be used to represent discontinuities in solid metallic structures. Discontinuity size and type cannot be characterized from phase angle and signal amplitude data developed with a surface scanning, pancake-type eddy current probe. It is concluded that the mercury model approach can greatly enhance the overall understanding and applicability of eddy current inspection techniques

Experimental Engineering: Articulating and Valuing Design Experimentation

DEFF Research Database (Denmark)

Vallgårda, Anna; Grönvall, Erik; Fritsch, Jonas

2017-01-01

In this paper we propose Experimental Engineering as a way to articulate open- ended technological experiments as a legitimate design research practice. Experimental Engineering introduces a move away from an outcome or result driven design process towards an interest in existing technologies and...

Tunneling current between graphene layers

OpenAIRE

Poklonski, Nikolai A.; Siahlo, Andrei I.; Vyrko, Sergey A.; Popov, Andrey M.; Lozovik, Yurii E.

2013-01-01

The physical model that allows to calculate the values of the tunneling current be-tween graphene layers is proposed. The tunneling current according to the pro-posed model is proportional to the area of tunneling transition. The calculated value of tunneling conductivity is in qualitative agreement with experimental data.

Defining the value of injection current and effective electrical contact area for EGaIn-based molecular tunneling junctions.

Science.gov (United States)

Simeone, Felice C; Yoon, Hyo Jae; Thuo, Martin M; Barber, Jabulani R; Smith, Barbara; Whitesides, George M

2013-12-04

Analysis of rates of tunneling across self-assembled monolayers (SAMs) of n-alkanethiolates SCn (with n = number of carbon atoms) incorporated in junctions having structure Ag(TS)-SAM//Ga2O3/EGaIn leads to a value for the injection tunnel current density J0 (i.e., the current flowing through an ideal junction with n = 0) of 10(3.6±0.3) A·cm(-2) (V = +0.5 V). This estimation of J0 does not involve an extrapolation in length, because it was possible to measure current densities across SAMs over the range of lengths n = 1-18. This value of J0 is estimated under the assumption that values of the geometrical contact area equal the values of the effective electrical contact area. Detailed experimental analysis, however, indicates that the roughness of the Ga2O3 layer, and that of the Ag(TS)-SAM, determine values of the effective electrical contact area that are ~10(-4) the corresponding values of the geometrical contact area. Conversion of the values of geometrical contact area into the corresponding values of effective electrical contact area results in J0(+0.5 V) = 10(7.6±0.8) A·cm(-2), which is compatible with values reported for junctions using top-electrodes of evaporated Au, and graphene, and also comparable with values of J0 estimated from tunneling through single molecules. For these EGaIn-based junctions, the value of the tunneling decay factor β (β = 0.75 ± 0.02 Å(-1); β = 0.92 ± 0.02 nC(-1)) falls within the consensus range across different types of junctions (β = 0.73-0.89 Å(-1); β = 0.9-1.1 nC(-1)). A comparison of the characteristics of conical Ga2O3/EGaIn tips with the characteristics of other top-electrodes suggests that the EGaIn-based electrodes provide a particularly attractive technology for physical-organic studies of charge transport across SAMs.

A current value Hamiltonian Approach for Discrete time Optimal Control Problems arising in Economic Growth

OpenAIRE

Naz, Rehana

2018-01-01

Pontrygin-type maximum principle is extended for the present value Hamiltonian systems and current value Hamiltonian systems of nonlinear difference equations for uniform time step $h$. A new method termed as a discrete time current value Hamiltonian method is established for the construction of first integrals for current value Hamiltonian systems of ordinary difference equations arising in Economic growth theory.

Experimental observations of stray current effects on steel fibres embedded in mortar

DEFF Research Database (Denmark)

Solgaard, A.O.S.; Carsana, M.; Geiker, M.R.

2013-01-01

It is known that stray direct current can cause corrosive damage over time to bar reinforced concrete, but knowledge on the consequences to steel fibre reinforced concrete is limited. This paper presents analyses and corresponding results from an experimental program (parametric study) investigat......It is known that stray direct current can cause corrosive damage over time to bar reinforced concrete, but knowledge on the consequences to steel fibre reinforced concrete is limited. This paper presents analyses and corresponding results from an experimental program (parametric study......) investigating the conditions required for current to be picked up by embedded steel fibres or reinforcement (rebars). The experiments showed that there is a clear ‘length effect’ related to the susceptibility of stray current being picked up by embedded steel (fibres or rebars): the shorter the reinforcement...

Currents, HF Radio-derived, SF Bay, 1 hr, Meridional, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 1 hour average of the meridional component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN EXPERIMENTAL...

Currents, HF Radio-derived, SF Bay, 1 hr, Zonal, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 1 hour average of the zonal component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN EXPERIMENTAL...

Currents, HF Radio-derived, Bodega Bay, 1 hr, Zonal, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 1 hour average of the zonal component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN EXPERIMENTAL...

An Experimental Evaluation of Blockage Corrections for Current Turbines

Science.gov (United States)

Ross, Hannah; Polagye, Brian

2017-11-01

Flow confinement has been shown to significantly alter the performance of turbines that extract power from water currents. These performance effects are related to the degree of constraint, defined by the ratio of turbine projected area to channel cross-sectional area. This quantity is referred to as the blockage ratio. Because it is often desirable to adjust experimental observations in water channels to unconfined conditions, analytical corrections for both wind and current turbines have been derived. These are generally based on linear momentum actuator disk theory but have been applied to turbines without experimental validation. This work tests multiple blockage corrections on performance and thrust data from a cross-flow turbine and porous plates (experimental analogues to actuator disks) collected in laboratory flumes at blockage ratios ranging between 10 and 35%. To isolate the effects of blockage, the Reynolds number, Froude number, and submergence depth were held constant while the channel width was varied. Corrected performance data are compared to performance in a towing tank at a blockage ratio of less than 5%. In addition to examining the accuracy of each correction, underlying assumptions are assessed to determine why some corrections perform better than others. This material is based upon work supported by the National Science Foundation Graduate Research Fellowship Program under Grant No. DGE-1256082 and the Naval Facilities Engineering Command (NAVFAC).

Experimental and theoretical studies of a high temperature cesium-barium tacitron, with application to low voltage-high current inversion

International Nuclear Information System (INIS)

Murray, C.S.; El-Genk, M.S.

1994-02-01

A low voltage/high current switch refer-red as ''Cs-Ba tacitron'' is studied for use as a dc to ac inverter in high temperature and/or ionizing radiation environments. The operational characteristics of the Cs-Ba tacitron as a switch were investigated experimentally in three modes: (a) breakdown mode, (b) I-V mode, and (c) current modulation mode. Operation parameters measured include switching frequencies up to 20 kHz, hold-off voltages up to 200 V, current densities in excess of 15 A/CM 2 , switch power density of 1 kW/cm 2 , and a switching efficiency in excess of 90 % at collector voltages greater than 30 V. Also, if the discharge current is circuit limited to a value below the maximum thermal emission current density, the voltage drop is constant and below 3 V

CVM-X: Calibrating contingent values with experimental auction markets

International Nuclear Information System (INIS)

Fox, J.A.; Shogren, J.F.; Hayes, D.J.; Kliebenstein, J.B.

1998-01-01

We design and implement a method, CVM-X, to calibrate hypothetical survey values using experimental auction markets. We test the procedure using consumer willingness-to-pay for irradiated/nonirradiated meat. Our results show that calibration factors for those who favor the irradiation process (0.67-0.69) are less severe than for those with an initial dislike of the process (0.55-0.59), suggesting that calibration may be commodity specific

Experimental typography : reviewing the modernist and the current approaches

OpenAIRE

Makal, Eray

1993-01-01

Ankara : The Department of Graphic Design and Institute of Fine Arts, Bilkent Univ., 1993. Thesis (Master's) -- Bilkent University, 1993. Includes bibliographical references leaves 65-66. The intention of this study is to evaluate the experimental typography within the history of graphic design by taking in consideration of two epochs. The Modernist and The Current. Makal, Eray M.S.

Creating Value through Virtual Teams: A Current Literature Review

Directory of Open Access Journals (Sweden)

Akemi Takeoka Chatfield

2014-11-01

Full Text Available Globally, virtual teams (VT as ICT-enabled emergent network organisation forms have gained international validity by innovative organisations, with a corresponding surge of interest in understanding how organisations can leverage VT to create business value. Despite growing deliberations in VT literature on managing VT, tasks and outcomes, however, creating business value through VT remains an unresolved theoretical and pragmatic conundrum. A review of prior relevant literature is essential to advancing knowledge. The paucity of published review articles seems to have impeded the field’s accumulation of VT knowledge. This research, therefore, reviews the current literature on case studies of VT to address the question: What are organisational challenges in creating business value through VT in the organisation? The key challenges found in the literature are effective communication, knowledge sharing, trust, and interpersonal skills in the new virtual boundary-less environment. Drawing on the IT business value model, we also discuss their resource-based implications.

Experimental Verification of Current Shear Design Equations for HSRC Beams

Directory of Open Access Journals (Sweden)

Attaullah Shah

2012-07-01

Full Text Available Experimental research on the shear capacity of HSRC (High Strength Reinforced Concrete beams is relatively very limited as compared to the NSRC (Normal Strength Reinforced Concrete beams. Most of the Building Codes determine the shear strength of HSRC with the help of empirical equations based on experimental work of NSRC beams and hence these equations are generally regarded as un-conservative for HSRC beams particularly at low level of longitudinal reinforcement. In this paper, 42 beams have been tested in two sets, such that in 21 beams no transverse reinforcement has been used, whereas in the remaining 21 beams, minimum transverse reinforcement has been used as per ACI-318 (American Concrete Institute provisions. Two values of compressive strength 52 and 61 MPa, three values of longitudinal steel ratio and seven values of shear span to depth ratio have been have been used. The beams were tested under concentrated load at the mid span. The results are compared with the equations proposed by different international building codes like ACI, AASHTO LRFD, EC (Euro Code, Canadian Code and Japanese Code for shear strength of HSRC beams.From comparison, it has been observed that some codes are less conservative for shear design of HSRC beams and further research is required to rationalize these equations.

CALCULATION-EXPERIMENTAL METHOD OF RESEARCH IN A METALLIC CONDUCTOR WITH THE PULSE CURRENT OF ELECTRONIC WAVEPACKAGES AND DE BROGLIE ELECTRONIC HALF-WAVES

Directory of Open Access Journals (Sweden)

M. I. Baranov

2016-12-01

Full Text Available Purpose. Development of calculation-experimental method for a discovery and study of electronic wavepackages (EWP and of de Broglie electronic half-waves in a metallic conductor with the pulse axial-flow current of high density. Methodology. Theoretical bases of the electrical engineering, bases of quantum physics, electrophysics bases of technique of high voltage and large pulsecurrents, and also bases of technique of measuring of permanent and variable electric value. Results. On the basis of generalization of results of research of features of the longitudinal wave periodic distributing of negatively charged transmitters of electric current of conductivity in the thin round continuous zincked steel wire offered and approved in the conditions of high-voltage laboratory method for a discovery and direct determination in him of geometrical parameters of «hot» and «cold» longitudinal areas quantized periodic longitudinal EWP and accordingly the mediated determination of values of the quantized lengths formative their de Broglie electronic half-waves. It is shown that results of close quantum mechanical calculations of EWP and quantized lengths λenz/2 of longitudinal de Broglie half-waves for the probed wire long l0 well comport with the results of the executed high temperature experiments on the powerful high-voltage generator of homopolar large pulse current of millisecond duration. Originality. First calculation-experimental a way the important for the theory of electricity fact of existence is set in a round metallic explorer with the impulsive axial-flow current of the quantized coherent de Broglie electronic half-waves, amplitudes of which at the quantum number of n=1,3,9 correspond the middles of «hot» longitudinal areas of EWP. Calculation quantum mechanical correlation of type of λenz/2=l0/n got experimental confirmation, in obedience to which on length of l0 conductor the integer of quantized electronic half-waves is always laid

Experimental Investigation of an Automobile Air-Conditioning System using Integrated Brushless Direct Current Motor Rotary Compressor

Directory of Open Access Journals (Sweden)

Sukri M.F.

2016-01-01

Full Text Available The present study presents an experimental investigation on the effect of condenser air inlet temperature and dimensionless parameter of X on the performance of automobile air-conditioning (AAC system using integrated brushless direct current motor-rotary compressor and electronic expansion valve. The other components of AAC system are from original component of AAC system used for medium size passenger car. The experimental results showed that the increment of the condenser air inlet temperature and X caused an increase in condensing temperature, cooling capacity and compressor work, while decreasing the coefficient of performance (COP. Meanwhile, the evaporating temperature increase with the increment of condenser air inlet temperature, but decrease with decrement of X. In general, AAC system have to work at higher value of X in order to produce more cooling capacity, thereby increment in compressor work also occurs due to energy balance. However, at higher value of X, the COP of the system dropped due to dominant increase in compressor power, as opposed to a rise in cooling capacity. Due to this reason, the best operation of this compressor occurs at X = 4.96 for constant T5 (35ºC, or at T5 = 30ºC for constant X (4.96.

Currents, HF Radio-derived, SF Bay Outlet, 1 hr, Meridional, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 1 hour average of the meridional component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN EXPERIMENTAL...

Distribution of local critical current along sample length and its relation to overall current in a long Bi2223/Ag superconducting composite tape

International Nuclear Information System (INIS)

Ochiai, S; Doko, D; Okuda, H; Oh, S S; Ha, D W

2006-01-01

The distribution of the local critical current and the n-value along the sample length and its relation to the overall critical current were studied experimentally and analytically for the bent multifilamentary Bi2223/Ag/Ag-Mg alloy superconducting composite tape. Then, based on the results, it was attempted to simulate on a computer the dependence of the critical current on the sample length. The main results are summarized as follows. The experimentally observed relation of the distributed local critical current and n-value to the overall critical current was described comprehensively with a simple voltage summation model, in which the sample was regarded as a one-dimensional series circuit. The sample length dependence of the critical current was reproduced on the computer by a Monte Carlo simulation incorporating the voltage summation model and the regression analysis results for the local critical current distribution and the relation of the n-value to the critical current

Current limiting capability of diffused resistors

International Nuclear Information System (INIS)

Shedd, W.; Cappelli, J.

1979-01-01

An experimental evaluation of the current limiting capability of dielectrically isolated diffused resistors at transient ionizing dose rates up to 6*10 12 rads(Si)/sec is presented. Existing theoretical predictions of the transient response of diffused resistors are summarized and compared to the experimentally measured values. The test resistors used allow the effects of sheet resistance and geometry on the transient response to be determined. The experimental results show that typical dielectrically isolated diffused resistors maintain adequate current limiting capability for use in radiation hardened integrated circuits

Currents, HF Radio-derived, Ano Nuevo, Normal Model, Meridional, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the meridional component of ocean surface currents derived from High Frequency Radio-derived measurements, with missing values filled in by a normal...

Currents, HF Radio-derived, Monterey Bay, Normal Model, Meridional, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the meridional component of ocean surface currents derived from High Frequency Radio-derived measurements, with missing values filled in by a normal...

Currents, HF Radio-derived, Monterey Bay, Normal Model, Zonal, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the zonal component of ocean surface currents derived from High Frequency Radio-derived measurements, with missing values filled in by a normal model....

Multi-Valued Associative Memory Neural Network

Institute of Scientific and Technical Information of China (English)

修春波; 刘向东; 张宇河

2003-01-01

A novel learning method for multi-valued associative memory network is introduced, which is based on Hebb rule, but utilizes more information. According to the current probe vector, the connection weights matrix could be chosen dynamically. Double-valued and multi-valued associative memory are all realized in our simulation experiment. The experimental results show that the method could enhance the associative success rate.

n value and Jc distribution dependence of AC transport current losses in HTS conductors

International Nuclear Information System (INIS)

Ogawa, Jun; Sawai, Yusuke; Nakayama, Haruki; Tsukamoto, Osami; Miyagi, Daisuke

2004-01-01

Compared with LTS materials, HTS materials have some peculiarities affecting AC loss characteristics of the conductors. We measured the AC transport current losses in YBCO thin film coated conductors and a Bi2223/Ag sheathed tape. Comparing the measured data with analytical calculations, the dependence of the AC transport current losses on the n value and critical current density distributions are studied. It is shown that, considering the n values and J c distributions, the peculiarities in the HTS materials can be taken into consideration and the transport current losses in HTS conductors can be calculated by the same analytical method used for LTS

Current-driven turbulence in plasmas

International Nuclear Information System (INIS)

Kluiver, H. de.

1977-10-01

Research on plasma heating in linear and toroidal systems using current-driven turbulence is reviewed. The motivation for this research is presented. Relations between parameters describing the turbulent plasma state and macroscopic observables are given. Several linear and toroidal devices used in current-driven turbulence studies are described, followed by a discussion of special diagnostic methods used. Experimental results on the measurement of electron and ion heating, anomalous plasma conductivity and associated turbulent fluctuation spectra are reviewed. Theories on current-driven turbulence are discussed and compared with experiments. It is demonstrated from the experimental results that current-driven turbulence occurs not only for extreme values of the electric field but also for an experimentally much more accessible and wide range of parameters. This forms a basis for a discussion on possible future applications in fusion-oriented plasma research

Reference values of fractional excretion of exhaled nitric oxide among non-smokers and current smokers.

Science.gov (United States)

Torén, Kjell; Murgia, Nicola; Schiöler, Linus; Bake, Björn; Olin, Anna-Carin

2017-08-25

Fractional exhaled nitric oxide (FE NO ) is used to assess of airway inflammation; diagnose asthma and monitor adherence to advised therapy. Reliable and accurate reference values for FE NO are needed for both non-smoking and current smoking adults in the clinical setting. The present study was performed to establish reference adult FE NO values among never-smokers, former smokers and current smokers. FE NO was measured in 5265 subjects aged 25-75 years in a general-population study, using a chemiluminescence (Niox ™) analyser according to the guidelines of the American Thoracic Society and the European Respiratory Society. Atopy was based on the presence of immunoglobulin E (IgE) antibodies to common inhalant allergens (measured using Phadiatop® test). Spirometry without bronchodilation was performed and forced vital capacity (FVC), forced expired volume in 1 s (FEV 1 ) and the ratio of FEV 1 to FVC values were obtained. After excluding subjects with asthma, chronic bronchitis, spirometric airway obstruction and current cold, 3378 subjects remained. Equations for predictions of FE NO values were modelled using nonparametric regression models. FE NO levels were similar in never-smokers and former smokers, and these two groups were therefore merged into a group termed "non-smokers". Reference equations, including the 5th and 95th percentiles, were generated for female and male non-smokers, based on age, height and atopy. Regression models for current smokers were unstable. Hence, the proposed reference values for current smokers are based on the univariate distribution of FE NO and fixed cut-off limits. Reference values for FE NO among respiratory healthy non-smokers should be outlined stratified for gender using individual reference values. For current smokers separate cut-off limits are proposed.

Field- and current-driven domain wall dynamics: An experimental picture

International Nuclear Information System (INIS)

Beach, G.S.D.; Knutson, C.; Tsoi, M.; Erskine, J.L.

2007-01-01

Field- and current-driven domain wall velocities are measured and discussed in terms of existing spin-torque models. A reversal in the roles of adiabatic and non-adiabatic spin-torque is shown to arise in those models below and above Walker breakdown. The measured dependence of velocity on current is the same in both regimes, indicating both spin-torque components have similar magnitude. However, the models on which these conclusions are based have serious quantitative shortcomings in describing the observed field-driven wall dynamics, for which they were originally developed. Hence, the applicability of simple one-dimensional models to most experimental conditions may be limited

Current transport modeling and experimental study of THz room temperature ballistic deflection transistors

Energy Technology Data Exchange (ETDEWEB)

Kaushal, Vikas; Margala, Martin [Department of Electrical and Computer Engineering, University of Massachusetts Lowell, MA, 01854 (United States); Yu Qiaoyan; Ampadu, Paul; Guarino, Gregg; Sobolewski, Roman, E-mail: vikas_kaushal@student.uml.ed [Department of Electrical and Computer Engineering, University of Rochester, NY, 14627 (United States)

2009-11-15

In this paper, two different theoretical models, Comsol Multiphysics{sup TM} (a Finite Element Analysis tool), and a field solver Atlas/Blaze from Silvaco, are compared qualitatively to study the effect of the deflector position, its size and electric field on the charge transport and its distribution along the channel, resulting in current outputs and leakages in ballistic deflection transistors (BDT). Silvaco simulations and experimental results were then used to study the lateral charge transport as a result of variation in electric field distribution, which controls the charge current along the channel in BDT. The electric field dependence of gain is also studied with experimental and theoretical results.

Current transport modeling and experimental study of THz room temperature ballistic deflection transistors

International Nuclear Information System (INIS)

Kaushal, Vikas; Margala, Martin; Yu Qiaoyan; Ampadu, Paul; Guarino, Gregg; Sobolewski, Roman

2009-01-01

In this paper, two different theoretical models, Comsol Multiphysics TM (a Finite Element Analysis tool), and a field solver Atlas/Blaze from Silvaco, are compared qualitatively to study the effect of the deflector position, its size and electric field on the charge transport and its distribution along the channel, resulting in current outputs and leakages in ballistic deflection transistors (BDT). Silvaco simulations and experimental results were then used to study the lateral charge transport as a result of variation in electric field distribution, which controls the charge current along the channel in BDT. The electric field dependence of gain is also studied with experimental and theoretical results.

Weak interactions and exchange currents in light nuclei. Theoretical and experimental aspects

International Nuclear Information System (INIS)

Guichon, P.

1980-01-01

The influence of meson exchange currents in the nuclear weak interaction is investigated theoretically and experimentally. The hypothesis of current algebra and partial conservation of axial current are used, through Adler-Dothan theorem, to derive the one pion exchange correction to the impulse approximation. Calculations are performed for partial transitions in the 1p-shell nuclei and in 16 O. The corrections are generally small except for the (0 + →0 - ) transition in 16 O where the large correction to the time component of the axial current can show up, due to selection rules. The measurement of the muon capture rate for this transition is described and an interpretation in term of exchange currents is proposed [fr

Experimentally determined profiles of fast wave current drive on DIII-D

International Nuclear Information System (INIS)

Forest, C.B.; Petty, C.C.; Baity, F.W.; Chiu, S.C.; deGrassie, J.S.; Groebner, R.J.; Ikezi, H.; Jaeger, E.F.; Kupfer, K.; Murakami, M.; Pinsker, R.I.; Prater, R.; Rice, B.W.; Wade, M.R.; Whyte, D.G.

1996-01-01

Profiles of non-inductive current driven by fast waves have been determined for reversed-shear DIII-D discharges. Both the current profile and toroidal electric field profile are determined from time sequences of equilibrium reconstructions [C. B. Forest et al., Phys. Rev. Lett. 73, 2224 (1994)]. Using this information, the measured current profile has been separated into inductive and non-inductive portions. By comparing similar discharges with co and counter antenna phasings and similar fast wave power, the portion of the total non-inductive current driven by fast waves was determined. The experimentally determined profiles of FWCD are in general agreement with theoretical predictions. Specifically, 135 kA was driven by 1.4 MW of rf power with a profile peaked inside ρ=2. copyright 1996 American Institute of Physics

Theoretical and Experimental Research of Synchronous Reluctance Motor

Science.gov (United States)

Dobriyan, R.; Vitolina, S.; Lavrinovicha, L.; Dirba, J.

2017-10-01

The paper presents the research on evaluation of accuracy of magnetic field calculations of synchronous reluctance motor in comparison with the results obtained in experiments. Magnetic field calculations are performed with the finite element method to determine values of the magnetic flux and electromagnetic torque according to the current value in motor stator and load angle between the rotor direct-axis and axis of stator magnetomotive force (MMF). Experimental values of magnetic flux and electromagnetic torque are obtained on motor with locked rotor while equivalent direct current is applied to the stator windings. The research shows that the results obtained from the magnetic field calculations coincide well with the experimental data.

Experimental observation of current generation by asymmetrical heating of ions in a tokamak plasma

International Nuclear Information System (INIS)

Gahl, J.; Ishihara, O.; Wong, K.L.; Kristiansen, M.; Hagler, M.

1986-01-01

The first experimental observation of current generation by asymmetrical heating of ions is reported. Ions were asymmetrically heated by a unidirectional fast Alfven wave launched by a slow wave antenna inside a tokamak. Current generation was detected by measuring the asymmetry of the toroidal plasma current with probes at the top and bottom of the toroidal plasma column

Theoretical and experimental studies on ionic currents in nanopore-based biosensors.

Science.gov (United States)

Liu, Lei; Li, Chu; Ma, Jian; Wu, Yingdong; Ni, Zhonghua; Chen, Yunfei

2014-12-01

Novel generation of analytical technology based on nanopores has provided possibilities to fabricate nanofluidic devices for low-cost DNA sequencing or rapid biosensing. In this paper, a simplified model was suggested to describe DNA molecule's translocation through a nanopore, and the internal potential, ion concentration, ionic flowing speed and ionic current in nanopores with different sizes were theoretically calculated and discussed on the basis of Poisson-Boltzmann equation, Navier-Stokes equation and Nernst-Planck equation by considering several important parameters, such as the applied voltage, the thickness and the electric potential distributions in nanopores. In this way, the basic ionic currents, the modulated ionic currents and the current drops induced by translocation were obtained, and the size effects of the nanopores were carefully compared and discussed based on the calculated results and experimental data, which indicated that nanopores with a size of 10 nm or so are more advantageous to achieve high quality ionic current signals in DNA sensing.

Experimental investigation of powerful pulse current generators based on capacitive storage and explosive magnetic generators

Science.gov (United States)

Shurupov, A. V.; Zavalova, V. E.; Kozlov, A. V.; Shurupov, M. A.; Povareshkin, M. N.; Kozlov, A. A.; Shurupova, N. P.

2018-01-01

Experimental models of microsecond duration powerful generators of current pulses on the basis of explosive magnetic generators and voltage impulse generator have been developed for the electromagnetic pulse effects on energy facilities to verify their stability. Exacerbation of voltage pulse carried out through the use of electro explosive current interrupter made of copper wires with diameters of 80 and 120 μm. Experimental results of these models investigation are represented. Voltage fronts about 100 ns and the electric field strength of 800 kV/m are registered.

A Survey of Current Valued Academic Leadership Qualities in Nursing.

Science.gov (United States)

Delgado, Cheryl; Mitchell, Maureen M

2016-01-01

An informal survey was used to identify nurse faculty leadership qualities currently valued and relevant. The accelerating retirement rate for seasoned leaders has created a need for nurse educators and academic leaders. Our school was concerned that we were not meeting students' needs for today's leadership challenges. We were also interested in the experiences of leadership preparation. This was a cross-sectional, online survey of faculty at top nursing schools as determined by US News & World Report. The top leadership qualities identified were integrity, communication clarity, and problem-solving ability. Current challenges for leaders were finding qualified faculty, obtaining resources, and team building. The results may guide curricular adjustments and the transition to a new generation of nurse academic leaders.

Experimental Demonstration of Higher Precision Weak-Value-Based Metrology Using Power Recycling

Science.gov (United States)

Wang, Yi-Tao; Tang, Jian-Shun; Hu, Gang; Wang, Jian; Yu, Shang; Zhou, Zong-Quan; Cheng, Ze-Di; Xu, Jin-Shi; Fang, Sen-Zhi; Wu, Qing-Lin; Li, Chuan-Feng; Guo, Guang-Can

2016-12-01

The weak-value-based metrology is very promising and has attracted a lot of attention in recent years because of its remarkable ability in signal amplification. However, it is suggested that the upper limit of the precision of this metrology cannot exceed that of classical metrology because of the low sample size caused by the probe loss during postselection. Nevertheless, a recent proposal shows that this probe loss can be reduced by the power-recycling technique, and thus enhance the precision of weak-value-based metrology. Here we experimentally realize the power-recycled interferometric weak-value-based beam-deflection measurement and obtain the amplitude of the detected signal and white noise by discrete Fourier transform. Our results show that the detected signal can be strengthened by power recycling, and the power-recycled weak-value-based signal-to-noise ratio can surpass the upper limit of the classical scheme, corresponding to the shot-noise limit. This work sheds light on higher precision metrology and explores the real advantage of the weak-value-based metrology over classical metrology.

High Accuracy Beam Current Monitor System for CEBAF'S Experimental Hall A

International Nuclear Information System (INIS)

J. Denard; A. Saha; G. Lavessiere

2001-01-01

CEBAF accelerator delivers continuous wave (CW) electron beams to three experimental Halls. In Hall A, all experiments require continuous, non-invasive current measurements and a few experiments require an absolute accuracy of 0.2 % in the current range from 1 to 180 (micro)A. A Parametric Current Transformer (PCT), manufactured by Bergoz, has an accurate and stable sensitivity of 4 (micro)A/V but its offset drifts at the muA level over time preclude its direct use for continuous measurements. Two cavity monitors are calibrated against the PCT with at least 50 (micro)A of beam current. The calibration procedure suppresses the error due to PCT's offset drifts by turning the beam on and off, which is invasive to the experiment. One of the goals of the system is to minimize the calibration time without compromising the measurement's accuracy. The linearity of the cavity monitors is a critical parameter for transferring the accurate calibration done at high currents over the whole dynamic range. The method for measuring accurately the linearity is described

Emission of biocides from hospitals: comparing current survey results with European Union default values.

Science.gov (United States)

Tluczkiewicz, Inga; Bitsch, Annette; Hahn, Stefan; Hahn, Torsten

2010-04-01

Under the European Union (EU) Biocidal Products Directive 98/8/EC, comprehensive evaluations on substances of the Third Priority List were conducted until 31 July 2007. This list includes, among other categories, disinfectants for human hygiene (e.g., skin and surface disinfection). For environmental exposure assessment of biocides, the EU emission scenarios apply. Currently available default values for disinfectants are based on consumption data from not more than 8 hospitals and were originally assembled for other purposes. To revalidate these default values, a survey on annual consumption data was performed in 27 German hospitals. These data were analyzed to provide consumption data per bed and day and per nurse and day for particular categories of active ingredients and were compared with default values from the EU emission scenario documents. Although several deviations were detected, an overall acceptable correspondence between Emission Scenario Documents default values and the current survey data was found. (c) 2009 SETAC

Experimental and Numerical Investigation of Local Scour Around Submarine Piggyback Pipeline Under Steady Current

Science.gov (United States)

Zhao, Enjin; Shi, Bing; Qu, Ke; Dong, Wenbin; Zhang, Jing

2018-04-01

As a new type of submarine pipeline, the piggyback pipeline has been gradually adopted in engineering practice to enhance the performance and safety of submarine pipelines. However, limited simulation work and few experimental studies have been published on the scour around the piggyback pipeline under steady current. This study numerically and experimentally investigates the local scour of the piggyback pipe under steady current. The influence of prominent factors such as pipe diameter, inflow Reynolds number, and gap between the main and small pipes, on the maximum scour depth have been examined and discussed in detail. Furthermore, one formula to predict the maximum scour depth under the piggyback pipeline has been derived based on the theoretical analysis of scour equilibrium. The feasibility of the proposed formula has been effectively calibrated by both experimental data and numerical results. The findings drawn from this study are instructive in the future design and application of the piggyback pipeline.

Using experimental game theory to transit human values to ethical AI

OpenAIRE

Wang, Yijia; Wan, Yan; Wang, Zhijian

2017-01-01

Knowing the reflection of game theory and ethics, we develop a mathematical representation to bridge the gap between the concepts in moral philosophy (e.g., Kantian and Utilitarian) and AI ethics industry technology standard (e.g., IEEE P7000 standard series for Ethical AI). As an application, we demonstrate how human value can be obtained from the experimental game theory (e.g., trust game experiment) so as to build an ethical AI. Moreover, an approach to test the ethics (rightness or wrongn...

Attitudes toward older adults: A matter of cultural values or personal values?

Science.gov (United States)

Zhang, Xin; Xing, Cai; Guan, Yanjun; Song, Xuan; Melloy, Robert; Wang, Fei; Jin, Xiaoyu

2016-02-01

The current research aimed to address the inconsistent findings regarding cultural differences in attitudes toward older adults by differentiating the effects of personal and cultural values. In Study 1, we used data from the sixth wave of the World Values Survey to examine attitudes toward older adults across cultures, and how different personal values (i.e., communal vs. agentic) and cultural values (i.e., individualism) predicted these attitudes. The results of hierarchical linear modeling analyses showed that after controlling for potential covariates, personal communal values positively correlated with positive attitudes toward older adults; however, cultural individualistic values did not. To further examine the causal effects of personal values (vs. cultural values), we conducted an experimental study and confirmed that priming personal values rather than cultural values had significant effects on ageism attitudes. The present studies help to reconcile conflicting results on cultural differences in attitudes toward older adults. (c) 2016 APA, all rights reserved).

Experimental demonstration of synergy between electron cyclotron and lower hybrid current drive on Tore Supra

International Nuclear Information System (INIS)

Artaud, J.F.; Giruzzi, G.; Dumont, R.J.; Imbeaux, F.; Bibet, P.; Bouquey, F.; Clary, J.; Ekedahl, A.; Hoang, G.T.; Lennholm, M.; Magne, R.; Segui, J.L.

2004-01-01

Non-inductive current drive (CD) has two main applications in tokamaks: sustainment of a substantial fraction of the toroidal plasma current necessary for the plasma confinement and control of the plasma stability and transport properties by appropriate shaping of the current density profile. For the first kind of applications, lower hybrid (LH) waves are known to provide the highest efficiency (defined as the ratio of the driven current to the injected wave power), although with limited control capability. Conversely, electron cyclotron (EC) waves drive highly localized currents, and are therefore particularly suited for control purposes, but their CD efficiency is much lower than that of LH waves (typically, an order of magnitude in present day experiments). Various calculations have demonstrated an interesting property: the current driven by the simultaneous use of the two waves, I(LH+EC), can be significantly larger than the sum I(LH)+I(EC) of the currents separately driven by the two waves in the same plasma conditions. This property, called synergy effect. The peculiar experimental conditions attainable on the Tore Supra tokamak have allowed the first experimental demonstration of the synergy between EC and LH current drive. The significant improvement of the electron cyclotron current drive (ECCD) efficiency in the presence of low hybrid current drive (LHCD), predicted by kinetic theory and confirmed by stationary experiments on Tore Supra, opens up the possibility of using ECCD as an efficient current profile control tool in LHCD plasmas

First experimental results with the Current Limit Avoidance System at the JET tokamak

Energy Technology Data Exchange (ETDEWEB)

De Tommasi, G. [Associazione EURATOM-ENEA-CREATE, Università di Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); Galeani, S. [Dipartimento di Informatica, Sistemi e Produzione, Università di Roma, Tor Vergata, Rome (Italy); Jachmich, S. [Association EURATOM-Belgian State, Koninklijke Militaire School - Ecole Royale Militaire, B-1000 Brussels (Belgium); Joffrin, E. [IRFM-CEA, Centre de Cadarache, 13108 Saint-paul-lez-Durance (France); Lennholm, M. [EFDA Close Support Unit, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); European Commission, B-1049 Brussels (Belgium); Lomas, P.J. [Euratom-CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Neto, A.C. [Associazione EURATOM-IST, Instituto de Plasmas e Fusao Nuclear, IST, 1049-001 Lisboa (Portugal); Maviglia, F. [Associazione EURATOM-ENEA-CREATE, Via Claudio 21, 80125 Napoli (Italy); McCullen, P. [Euratom-CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Pironti, A. [Associazione EURATOM-ENEA-CREATE, Università di Napoli Federico II, Via Claudio 21, 80125 Napoli (Italy); Rimini, F.G. [Euratom-CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Sips, A.C.C. [European Commission, B-1049 Brussels (Belgium); Varano, G.; Vitelli, R. [Dipartimento di Informatica, Sistemi e Produzione, Università di Roma, Tor Vergata, Rome (Italy); Zaccarian, L. [CNRS, LAAS, 7 Avenue du Colonel Roche, F-31400 Toulouse (France); Universitè de Toulouse, LAAS, F-31400 Toulouse (France)

2013-06-15

The Current Limit Avoidance System (CLA) has been recently deployed at the JET tokamak to avoid current saturations in the poloidal field (PF) coils when the eXtreme Shape Controller is used to control the plasma shape. In order to cope with the current saturation limits, the CLA exploits the redundancy of the PF coils system to automatically obtain almost the same plasma shape using a different combination of currents in the PF coils. In the presence of disturbances it tries to avoid the current saturations by relaxing the constraints on the plasma shape control. The CLA system has been successfully implemented on the JET tokamak and fully commissioned in 2011. This paper presents the first experimental results achieved in 2011–2012 during the restart and the ITER-like wall campaigns at JET.

Transportation safety aspects of ore and related material - inconsistencies in current exemption values

International Nuclear Information System (INIS)

Rawl, R.R.; Leggett, R.W.; Eckerman, K.F.; Cook, J.R.

2004-01-01

The IAEA's system for exemption of material from the transport regulations is based on the fundamental principle that exemption values should be commensurate with the risk posed by the material, as represented by effective dose and skin dose. Important departures from that principle as well as inconsistencies between exemption values for different radionuclides have resulted from special provisions for natural materials that depend on their intended use, and from exposure scenarios and other assumptions and rules used in the derivation of exemption values. This paper examines the sources and extent of inconsistencies in exemption values for transport, particularly as they relate to naturally occurring radionuclides, and suggests ways to achieve greater internal consistency in exemption values as well as greater consistency with the fundamental principle underlying the current system

EXPERIMENTAL RESEARCHES OF ELECTRO-THERMAL RESISTIBILITY OF SEND-OFFS AND CABLES TO ACTION RATIONED ON THE INTERNATIONAL STANDARD OF IEC 62305-1-2010 OF APERIODIC IMPULSE OF CURRENT OF ARTIFICIAL LIGHTNING

Directory of Open Access Journals (Sweden)

M.I. Baranov

2016-03-01

Full Text Available Purpose. Experimental researches of electro-thermal resistibility of cable-explorer products, applied in the power electric circuits of objects of electric-power industry, to action on its copper and aluminum parts bearings a current rationed on the International Standard of IEC 62305-1-2010 aperiodic impulse 10/350 μs of current of artificial lightning. Methodology. Electrophysics bases of technique of high tensions and high pulsed currents (HPC, and also scientific and technical bases of planning of devices of high-voltage impulsive technique and measuring HPC in them. Results. Experimental a way the quantitative levels of maximal values maximum of possible and critical closenesses of aperiodic impulse 10/350 μs of current of artificial lightning with rationed on the international standard of IEC 62305-1-2010 peak-temporal parameters and admittances on them in copper (aluminum parts bearings a current of send-offs and cables with a polyethylene (PET and polyvinylchloride (PVCH isolation. Originality. First in world practice on the unique powerful high-voltage generator of HPC of artificial lightning experimental researches of resistibility to lightning of pre-production models of send-offs (cables are conducted with copper (aluminum tendons, PET and PVCH by an isolation, in-use in power electric circuits of electric-power industry objects. Practical value. The use in practice of protecting from lightning of the got results will allow substantially to promote functional and fire-prevention safety of engineering communications of objects of industrial electroenergy in the conditions of action on them of short shots of linear lightning.

Current control of superconducting coils for fusion experimental facility

International Nuclear Information System (INIS)

Ise, T.; Etou, D.; Chikaraishi, H.; Takami, S.; Inoue, T.

2003-01-01

The LHD (Large Helical Device) has twelve superconducting coils and six dc power supplies, and following specifications are required for its control system; each coil current must be controlled independently, the steady state control error is less than 0.01% of the reference value, the current settling time for 0.1% of control error is less than 1 second, and the control system must be robust against turbulence caused by appearance and disappearance of the plasma, parameter errors and external electro-magnetic noises. In this paper, the design and test results of the coil current control system for the LHD are described. The good response and robustness are in the relation of trade off each other. H-infinity controller is one of schemes to guarantee robustness for stability. However, the independent responses of six coils were impossible by the H-infinity controller only. To resolve this problem, we applied a feed-forward control with the H-infinity control. Moreover, the advanced design method of H-infinity controller using μ-synthesis was applied to guarantee the control performance in the whole operating condition. As a result, good control results were obtained by experiments. (author)

General Potential-Current Model and Validation for Electrocoagulation

International Nuclear Information System (INIS)

Dubrawski, Kristian L.; Du, Codey; Mohseni, Madjid

2014-01-01

A model relating potential and current in continuous parallel plate iron electrocoagulation (EC) was developed for application in drinking water treatment. The general model can be applied to any EC parallel plate system relying only on geometric and tabulated input variables without the need of system-specific experimentally derived constants. For the theoretical model, the anode and cathode were vertically divided into n equipotential segments in a single pass, upflow, and adiabatic EC reactor. Potential and energy balances were simultaneously solved at each vertical segment, which included the contribution of ionic concentrations, solution temperature and conductivity, cathodic hydrogen flux, and gas/liquid ratio. We experimentally validated the numerical model with a vertical upflow EC reactor using a 24 cm height 99.99% pure iron anode divided into twelve 2 cm segments. Individual experimental currents from each segment were summed to determine total current, and compared with the theoretically derived value. Several key variables were studied to determine their impact on model accuracy: solute type, solute concentration, current density, flow rate, inter-electrode gap, and electrode surface condition. Model results were in good agreement with experimental values at cell potentials of 2-20 V (corresponding to a current density range of approximately 50-800 A/m 2 ), with mean relative deviation of 9% for low flow rate, narrow electrode gap, polished electrodes, and 150 mg/L NaCl. Highest deviation occurred with a large electrode gap, unpolished electrodes, and Na 2 SO 4 electrolyte, due to parasitic H 2 O oxidation and less than unity current efficiency. This is the first general model which can be applied to any parallel plate EC system for accurate electrochemical voltage or current prediction

Comparison of experimental and theoretical reaction rail currents, rail voltages, and airgap fields for the linear induction motor research vehicle

Science.gov (United States)

Elliott, D. G.

1977-01-01

Measurements of reaction rail currents, reaction rail voltages, and airgap magnetic fields in tests of the Linear Induction Motor Research Vehicle (LIMRV) were compared with theoretical calculations from the mesh/matrix theory. It was found that the rail currents and magnetic fields predicted by the theory are within 20 percent of the measured currents and fields at most motor locations in most of the runs, but differ by as much as a factor of two in some cases. The most consistent difference is a higher experimental than theoretical magnetic field near the entrance of the motor and a lower experimental than theoretical magnetic field near the exit. The observed differences between the theoretical and experimental magnetic fields and currents do not account for the differences of as much as 26 percent between the theoretical and experimental thrusts.

30 CFR 75.601-3 - Short circuit protection; dual element fuses; current ratings; maximum values.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Short circuit protection; dual element fuses... Trailing Cables § 75.601-3 Short circuit protection; dual element fuses; current ratings; maximum values. Dual element fuses having adequate current-interrupting capacity shall meet the requirements for short...

Effect of Wave Accessibility on Lower Hybrid Wave Current Drive in Experimental Advanced Superconductor Tokamak with H-Mode Operation

International Nuclear Information System (INIS)

Li Xin-Xia; Xiang Nong; Gan Chun-Yun

2015-01-01

The effect of the wave accessibility condition on the lower hybrid current drive in the experimental advanced superconductor Tokamak (EAST) plasma with H-mode operation is studied. Based on a simplified model, a mode conversion layer of the lower hybrid wave between the fast wave branch and the slow wave branch is proved to exist in the plasma periphery for typical EAST H-mode parameters. Under the framework of the lower hybrid wave simulation code (LSC), the wave ray trajectory and the associated current drive are calculated numerically. The results show that the wave accessibility condition plays an important role on the lower hybrid current drive in EAST plasma. For wave rays with parallel refractive index n ‖ = 2.1 or n ‖ = 2.5 launched from the outside midplane, the wave rays may penetrate the core plasma due to the toroidal geometry effect, while numerous reflections of the wave ray trajectories in the plasma periphery occur. However, low current drive efficiency is obtained. Meanwhile, the wave accessibility condition is improved if a higher confined magnetic field is applied. The simulation results show that for plasma parameters under present EAST H-mode operation, a significant lower hybrid wave current drive could be obtained for the wave spectrum with peak value n ‖ = 2.1 if a toroidal magnetic field B T = 2.5 T is applied. (paper)

Radiation induced currents in mineral-insulated cables and in pick-up coils: model calculations and experimental verification in the BR1 reactor

Science.gov (United States)

Vermeeren, Ludo; Leysen, Willem; Brichard, Benoit

2018-01-01

1 to 7 nA only, putting a challenge on the acquisition system and on the data analysis. The detailed experimental results will be compared with the corresponding values predicted by the model. The overall agreement between the experimental data and the model predictions is fairly good, with very consistent data for the main delayed current components, while the lower amplitude delayed currents and some of the prompt contributions show some minor discrepancies.

Theoretical calculations of L alpha one x-ray emission intensity ratios for uranium in various matrices: a comparison with experimental values

International Nuclear Information System (INIS)

Anderson, L.D.

1976-01-01

The U L/sub α1/ x-ray emission intensity ratios (I/sub lambda/sub L//I sub lambda/sub L/, sub 100 percent/sub UO 2 /) in various matrices were calculated using the fundamental parameters formula of Criss and Birks and mass absorption coefficients calculated from a formula developed by Dewey. The use of the intensity ratio made it unnecessary to know the fluorescence yield for the U L/sub III/ level, the probability of emission of the U L/sub α1/ line, and the jump ratios for the three absorption edges of uranium. Also, since an intensity ratio was used, the results are independent of the x-ray tube current and the spectral distribution of the x-ray tube. A method is presented to calculate the intensity ratios for x-ray tube voltages other than the value (45 kV) used in the calculations. The theoretical results are calculated and compared with the experimental results obtained for 141 matrices. Difficulties due to oxidation of some of the metal powders used in the sample preparation, to small concentrations of uranium, and to an excessively large number of elements present in some of the samples resulted in the invalidation of the experimental results for 91 of the matrices. For the remaining 50 matrices, the theoretical and experimental values agreed to within +-5 percent relative error for 36 matrices; to within +-5 percent to +- 10 percent for 7 matrices; to within +-10 percent to +-20 percent for 6 matrices; and was greater than +-20 percent for 1 matrix

Current and Voltage Conveyors in Current- and Voltage-Mode Precision Full-Wave Rectifiers

Directory of Open Access Journals (Sweden)

J. Koton

2011-04-01

Full Text Available In this paper new versatile precision full-wave rectifiers using current and/or voltage conveyors as active elements and two diodes are presented. The performance of these circuit solutions is analysed and compared to the opamp based precision rectifier. To analyze the behavior of the functional blocks, the frequency dependent RMS error and DC transient value are evaluated for different values of input voltage amplitudes. Furthermore, experimental results are given that show the feasibilities of the conveyor based rectifiers superior to the corresponding operational amplifier based topology.

Application of bias factor method with use of virtual experimental value to prediction uncertainty reduction in void reactivity worth of breeding light water reactor

International Nuclear Information System (INIS)

Kugo, Teruhiko; Mori, Takamasa; Kojima, Kensuke; Takeda, Toshikazu

2007-01-01

We have carried out the critical experiments for the MOX fueled tight lattice LWR cores using FCA facility and constructed the XXII-1 series cores. Utilizing the critical experiments carried out at FCA, we have evaluated the reduction of prediction uncertainty in the coolant void reactivity worth of the breeding LWR core based on the bias factor method with focusing on the prediction uncertainty due to cross section errors. In the present study, we have introduced a concept of a virtual experimental value into the conventional bias factor method to overcome a problem caused by the conventional bias factor method in which the prediction uncertainty increases in the case that the experimental core has the opposite reactivity worth and the consequent opposite sensitivity coefficients to the real core. To extend the applicability of the bias factor method, we have adopted an exponentiated experimental value as the virtual experimental value and formulated the prediction uncertainty reduction by the use of the bias factor method extended by the concept of the virtual experimental value. From the numerical evaluation, it has been shown that the prediction uncertainty due to cross section errors has been reduced by the use of the concept of the virtual experimental value. It is concluded that the introduction of virtual experimental value can effectively utilize experimental data and extend applicability of the bias factor method. (author)

Current Parental Depression and Offspring Perceived Self-Competence: A Quasi-Experimental Examination

OpenAIRE

Class, Quetzal A.; D’Onofrio, Brian M.; Singh, Amber L.; Ganiban, Jody M.; Spotts, E. L.; Lichtenstein, Paul; Reiss, David; Neiderhiser, Jenae M.

2012-01-01

A genetically-informed, quasi-experimental design was used to examine the genetic and environmental processes underlying associations between current parental depressive symptoms and offspring perceived self-competence. Participants, drawn from a population-based Swedish sample, were 852 twin pairs and their male (52%) and female offspring aged 15.7 ± 2.4 years. Parental depressive symptoms were measured using the Center for Epidemiological Studies Depression scale. Offspring perceived self-c...

Estimating patient dose from CT exams that use automatic exposure control: Development and validation of methods to accurately estimate tube current values.

Science.gov (United States)

McMillan, Kyle; Bostani, Maryam; Cagnon, Christopher H; Yu, Lifeng; Leng, Shuai; McCollough, Cynthia H; McNitt-Gray, Michael F

2017-08-01

The vast majority of body CT exams are performed with automatic exposure control (AEC), which adapts the mean tube current to the patient size and modulates the tube current either angularly, longitudinally or both. However, most radiation dose estimation tools are based on fixed tube current scans. Accurate estimates of patient dose from AEC scans require knowledge of the tube current values, which is usually unavailable. The purpose of this work was to develop and validate methods to accurately estimate the tube current values prescribed by one manufacturer's AEC system to enable accurate estimates of patient dose. Methods were developed that took into account available patient attenuation information, user selected image quality reference parameters and x-ray system limits to estimate tube current values for patient scans. Methods consistent with AAPM Report 220 were developed that used patient attenuation data that were: (a) supplied by the manufacturer in the CT localizer radiograph and (b) based on a simulated CT localizer radiograph derived from image data. For comparison, actual tube current values were extracted from the projection data of each patient. Validation of each approach was based on data collected from 40 pediatric and adult patients who received clinically indicated chest (n = 20) and abdomen/pelvis (n = 20) scans on a 64 slice multidetector row CT (Sensation 64, Siemens Healthcare, Forchheim, Germany). For each patient dataset, the following were collected with Institutional Review Board (IRB) approval: (a) projection data containing actual tube current values at each projection view, (b) CT localizer radiograph (topogram) and (c) reconstructed image data. Tube current values were estimated based on the actual topogram (actual-topo) as well as the simulated topogram based on image data (sim-topo). Each of these was compared to the actual tube current values from the patient scan. In addition, to assess the accuracy of each method in estimating

Experimental Investigation of a Direct Methanol Fuel Cell with Hilbert Fractal Current Collectors

Directory of Open Access Journals (Sweden)

Jing-Yi Chang

2014-01-01

Full Text Available The Hilbert curve is a continuous type of fractal space-filling curve. This fractal curve visits every point in a square grid with a size of 2×2, 4×4, or any other power of two. This paper presents Hilbert fractal curve application to direct methanol fuel cell (DMFC current collectors. The current collectors are carved following first, second, and third order Hilbert fractal curves. These curves give the current collectors different free open ratios and opening perimeters. We conducted an experimental investigation into DMFC performance as a function of the free open ratio and opening perimeter on the bipolar plates. Nyquist plots of the bipolar plates are made and compared using electrochemical impedance spectroscopy (EIS experiments to understand the phenomena in depth. The results obtained in this paper could be a good reference for future current collector design.

Optimization of Experimental Conditions of the Pulsed Current GTAW Parameters for Mechanical Properties of SDSS UNS S32760 Welds Based on the Taguchi Design Method

Science.gov (United States)

Yousefieh, M.; Shamanian, M.; Saatchi, A.

2012-09-01

Taguchi design method with L9 orthogonal array was implemented to optimize the pulsed current gas tungsten arc welding parameters for the hardness and the toughness of super duplex stainless steel (SDSS, UNS S32760) welds. In this regard, the hardness and the toughness were considered as performance characteristics. Pulse current, background current, % on time, and pulse frequency were chosen as main parameters. Each parameter was varied at three different levels. As a result of pooled analysis of variance, the pulse current is found to be the most significant factor for both the hardness and the toughness of SDSS welds by percentage contribution of 71.81 for hardness and 78.18 for toughness. The % on time (21.99%) and the background current (17.81%) had also the next most significant effect on the hardness and the toughness, respectively. The optimum conditions within the selected parameter values for hardness were found as the first level of pulse current (100 A), third level of background current (70 A), first level of % on time (40%), and first level of pulse frequency (1 Hz), while they were found as the second level of pulse current (120 A), second level of background current (60 A), second level of % on time (60%), and third level of pulse frequency (5 Hz) for toughness. The Taguchi method was found to be a promising tool to obtain the optimum conditions for such studies. Finally, in order to verify experimental results, confirmation tests were carried out at optimum working conditions. Under these conditions, there were good agreements between the predicted and the experimental results for the both hardness and toughness.

Influence of premium versus value brand names on the smoking experience in a plain packaging environment: an experimental study.

Science.gov (United States)

Skaczkowski, Gemma; Durkin, Sarah; Kashima, Yoshihisa; Wakefield, Melanie

2017-01-16

To examine the effect of branding, as indicated by brand name, on evaluation of the cigarette smoking experience. Between-subjects and within-subjects experimental study. Participants were randomly allocated to smoke a cigarette from a pack featuring a premium brand name and a cigarette from a pack featuring a value brand name. Within each condition, participants unknowingly smoked two identical cigarettes (either two premium or two value cigarettes). Australia, October 2014, 2 years after tobacco plain packaging implementation. 81 current cigarette smokers aged 19-39 years. From apparently premium and value brand-name packs, 40 smokers were allocated to smoke the same actual premium cigarettes and 41 were allocated to smoke the same actual value cigarettes. Experienced taste (flavour, satisfaction, enjoyment, quality, liking, mouthfeel and aftertaste), harshness, dryness, staleness, harm/strength measures (strength, tar, lightness, volume of smoke), draw effort and purchase intent. Cigarettes given a premium brand name were rated as having a better taste, were less harsh and less dry than identical cigarettes given a value brand name. This pattern was observed irrespective of whether the two packs actually contained premium or value cigarettes. These effects were specific: the brand name did not influence ratings of cigarette variant attributes (strength, tar, volume of smoke, lightness and draw effort). Despite the belief that brand names represent genuine differences between cigarette products, the results suggest that at least some of this perceived sensory difference is attributable to brand image. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Numerical and experimental studies of stack shunt current for vanadium redox flow battery

International Nuclear Information System (INIS)

Yin, Cong; Guo, Shaoyun; Fang, Honglin; Liu, Jiayi; Li, Yang; Tang, Hao

2015-01-01

Highlights: • A coupled three-dimensional model of VRB cell stack is developed. • Shunt current of the stack is studied with the model and experiment. • Increased electrolyte resistance in channel and manifold lowers the shunt current. • Shunt current loss increases with stack cell number nonlinearly. - Abstract: The stack shunt current of VRB (vanadium redox flow battery) was investigated with experiments and 3D (three-dimensional) simulations. In the proposed model, cell voltages and electrolyte conductivities were calculated based on electrochemical reaction distributions and SOC (state of charge) values, respectively, while coulombic loss was estimated according to shunt current and vanadium ionic crossover through membrane. Shunt current distributions and coulombic efficiency are analyzed in terms of electrolyte conductivities and stack cell numbers. The distributions of cell voltages and shunt currents calculated with proposed model are validated with single cell and short stack tests. The model can be used to optimize VRB stack manifold and channel designs to improve VRB system efficiency

Valores, Creencias Y Objectivos: Base del programa de la Escuela Experimental P.K. Yonge. (Values, Beliefs and Objectives: The Basis of Experimental Schools P.K. Yonge's Program.)

Science.gov (United States)

Florida Univ., Gainesville. Coll. of Education.

The values, beliefs, and objectives that form the core of the program at the Experimental School P.K. Yonge in the University of Florida are presented in this paper which is written in Spanish. This experimental school serves approximately 900 students from grades one through twelve. The function of the school is to conduct research to solve…

PENGARUH PENERAPAN FAIR VALUE NON CURRENT ASSET DAN MANAJEMEN PAJAK ATAS ASSET PERUSAHAAN TERHADAP FEE AUDIT

Directory of Open Access Journals (Sweden)

R Nelly Nur Apandi

2016-12-01

Full Text Available Abstract. The implementation of international accounting standards has increased fair value implementation in financial reporting. The benefit is that fair value represents the true economic condition of an entity. On the other hand, this concept also causes problem related to its measurement subjectivity, especially on non current asset. It makes the auditor do a greater effort to gain a sufficient conviction over the fairness of non current asset. This implicates a greater audit fee. This study aims to seek the effect of fair value of non current asset on audit fee. This study also aims to seek any moderation from tax management of companies asset that affects the relationship between fair value implementation and audit fee. By using OLS regression, this study examines companies listed in Indonesia Stock Exchange from 2012 to 2014, with a sample of 114 companies. The result show that fair value implementation affects audit fee and this study is able to prove that fair value implementation moderated by tax management of company asset affects audit fee. Keywords: Fair Value Non Current Asset; Tax Management; Audit Fee   Abstrak. Penerapan standar akuntansi internasional telah meningkatkan penerapan nilai wajar dalam pelaporan keuangan. Manfaatnya adalah bahwa nilai wajar merupakan kondisi ekonomi sebenarnya dari suatu entitas. Di sisi lain, konsep ini juga menyebabkan masalah yang berkaitan dengan subjektivitas pengukurannya, terutama pada aset tidak lancar. Hal ini membuat auditor melakukan upaya yang lebih besar untuk mendapatkan keyakinan yang memadai atas kewajaran aset tidak lancar. Ini berimplikasi pada biaya audit yang lebih besar. Penelitian ini bertujuan untuk mengetahui pengaruh nilai wajar aktiva tidak lancar terhadap biaya audit. Penelitian ini juga bertujuan untuk mencari moderasi dari pengelolaan pajak aset perusahaan yang mempengaruhi hubungan antara penerapan nilai wajar dan biaya audit. Dengan menggunakan regresi OLS

Faculty perceptions of the strengths, weaknesses and future prospects of the current medical undergraduate experimental physiology curriculum in Gujarat, India.

Science.gov (United States)

Paralikar, Swapnil; Shah, Chinmay

2015-01-01

Over the past several years, an opinion has emerged in India that the current practical curricula in medical schools fail to meet many of the objectives for which they were instituted. Hence, this study has assessed the perception of physiology faculty members regarding the current experimental physiology curriculum in one Indian state, Gujarat. The faculty were of the opinion that many of the topics currently taught in experimental physiology (amphibian nerve-muscle and heart muscle experiments) were outdated and clinically irrelevant: Therefore, the faculty advocated that duration of teaching time devoted to some of these topics should be reduced and topics with clinical relevance should be introduced at the undergraduate level. The faculty also felt that more emphasis should be laid on highlighting the clinical aspect related to each concept taught in experimental physiology . Moreover, a majority of faculty members were in favour of replacing the current practice in Gujarat of teaching experimental physiology only by explanation of graphs obtained from experiments conducted in the previous years, with computer assisted learning in small groups.

Maternal hypothyroidism: An overview of current experimental models.

Science.gov (United States)

Ghanbari, Mahboubeh; Ghasemi, Asghar

2017-10-15

Maternal hypothyroidism (MH) is the most common cause of transient congenital hypothyroidism. Different animal models are used for assessing developmental effects of MH in offspring. The severity and status of hypothyroidism in animal models must be a reflection of the actual conditions in humans. To obtain comparable results with different clinical conditions, which lead to MH in humans, several factors have been suggested for researchers to consider before designing the experimental models. Regarding development of fetal body systems during pregnancy, interference at different times provides different results and the appropriate time for induction of hypothyroidism should be selected based on accurate time of development of the system under assessment. Other factors that should be taken into consideration include, physiological and biochemical differences between humans and other species, thyroid hormone-independent effects of anti-thyroid drugs, circadian rhythms in TSH secretion, sex differences, physical and psychological stress. This review addresses essential guidelines for selecting and managing the optimal animal model for MH as well as discussing the pros and cons of currently used models. Copyright © 2017 Elsevier Inc. All rights reserved.

Electrostatic contribution of surface charge residues to the stability of a thermophilic protein: benchmarking experimental and predicted pKa values.

Directory of Open Access Journals (Sweden)

Chi-Ho Chan

Full Text Available Optimization of the surface charges is a promising strategy for increasing thermostability of proteins. Electrostatic contribution of ionizable groups to the protein stability can be estimated from the differences between the pKa values in the folded and unfolded states of a protein. Using this pKa-shift approach, we experimentally measured the electrostatic contribution of all aspartate and glutamate residues to the stability of a thermophilic ribosomal protein L30e from Thermococcus celer. The pKa values in the unfolded state were found to be similar to model compound pKas. The pKa values in both the folded and unfolded states obtained at 298 and 333 K were similar, suggesting that electrostatic contribution of ionizable groups to the protein stability were insensitive to temperature changes. The experimental pKa values for the L30e protein in the folded state were used as a benchmark to test the robustness of pKa prediction by various computational methods such as H++, MCCE, MEAD, pKD, PropKa, and UHBD. Although the predicted pKa values were affected by crystal contacts that may alter the side-chain conformation of surface charged residues, most computational methods performed well, with correlation coefficients between experimental and calculated pKa values ranging from 0.49 to 0.91 (p<0.01. The changes in protein stability derived from the experimental pKa-shift approach correlate well (r = 0.81 with those obtained from stability measurements of charge-to-alanine substituted variants of the L30e protein. Our results demonstrate that the knowledge of the pKa values in the folded state provides sufficient rationale for the redesign of protein surface charges leading to improved protein stability.

Q-values of mirror transitions for fundamental interaction studies

CERN Multimedia

The $Ft$ values for the $0^{+} \\rightarrow 0^{+}$ superallowed $\\beta$-transitions currently provide the best test of the CVC hypothesis, and the most precise determination of the V$_{ud}$ element of the CKM matrix. Recent experimental advances, including direct mass measurements with Penning traps, have led to the precision in the corrected $Ft$ values being dominated by the theoretical corrections rather than experiment. An alternative route are the isospin $T$=1/2 mirror transitions where experimental uncertainties dominate over the theoretical inputs and which can provide an independent test of CVC, and ultimately an independent evaluation of V$_{ud}$. We propose mass measurements of 4 different mirror transitions aiming for a precision of better than 100eV on the ${Q}$-values.

Current efficiency in the chlorate cell process

Directory of Open Access Journals (Sweden)

Spasojević Miroslav D.

2014-01-01

Full Text Available A mathematical model has been set up for current efficiency in a chlorate cell acting as an ideal electrochemical tubular reactor with a linear increase in hypochlorite concentration from the entrance to the exit. Good agreement was found between the results on current efficiency experimentally obtained under simulated industrial chlorate production conditions and the theoretical values provided by the mathematical model. [Projekat Ministarstva nauke Republike Srbije, br. 172057 i br. 172062

The concept of average LET values determination

International Nuclear Information System (INIS)

Makarewicz, M.

1981-01-01

The concept of average LET (linear energy transfer) values determination, i.e. ordinary moments of LET in absorbed dose distribution vs. LET of ionizing radiation of any kind and any spectrum (even the unknown ones) has been presented. The method is based on measurement of ionization current with several values of voltage supplying an ionization chamber operating in conditions of columnar recombination of ions or ion recombination in clusters while the chamber is placed in the radiation field at the point of interest. By fitting a suitable algebraic expression to the measured current values one can obtain coefficients of the expression which can be interpreted as values of LET moments. One of the advantages of the method is its experimental and computational simplicity. It has been shown that for numerical estimation of certain effects dependent on LET of radiation it is not necessary to know the dose distribution but only a number of parameters of the distribution, i.e. the LET moments. (author)

Relation of n-value to critical current for local sections and overall sample in a SmBCO coated conductor pulled in tension

International Nuclear Information System (INIS)

Ochiai, Shojiro; Okuda, Hiroshi; Nagano, Shinji; Sugano, Michinaka; Oh, Sang-Song; Ha, Hong-Soo; Osamura, Kozo

2014-01-01

Under application of tensile stress to a SmBCO (SmBa 2 Cu 3 O 7-δ ) coated conductor sample consisting of series electric circuit of local sections, the relation of voltage-current curve, critical current and n-value of the sections to those of overall sample was studied. The change in critical current and n-value with increasing applied stress was different from section to section due to the difference in damage behavior of the SmBCO layer among the sections. When the difference in extent of damage among the sections was small, the voltages developed in all sections contributed to the voltage of overall sample. In this case, the critical current and n-value of overall sample were within the range of the highest and lowest values among the sections. On the other hand, when the damage in one section was far severer than that of other sections, the voltage developed in the most severely damaged section largely contributed to the overall voltage, and hence the voltage-current curves of the most severely damaged section were almost the same as those of overall sample. In this case, critical current of the overall sample was slightly higher and n-value of the overall sample was lower than the critical current and n-value of the most severely damaged section. Accordingly, the decrease in n-value with decreasing critical current in overall sample was sharper than that in sections. This phenomenon was accounted for by the increase in shunting current at cracked part at higher voltage in the most severely damaged section. (author)

The influence of tensile strain to critical current of Bi2223 composite tape

International Nuclear Information System (INIS)

Mukai, Y.; Shin, J.K.; Ochiai, S.; Okuda, H.; Sugano, M.; Osamura, K.

2008-01-01

As the stress-induced damage evolution is different from position to position in the sample, the local critical current is scattered in a sample, affecting on the overall current. The present work aimed to describe the distribution of local critical current and its relation to overall critical current under tensile stress for Bi2223/Ag superconducting composite tape. In the experiment, seven voltage probes were attached in a step of 10 mm. The local critical current and n-value at 77 K under various applied stress levels were measured for a voltage probe distance 10 mm and the overall ones for a probe distance 60 mm. Main results are summarized as follows. The overall critical current and n-value were described well by using the voltage summation model in which the sample was regarded as a one dimensional series circuit. For the low applied stress, the distribution of local critical current was described with the three parameter Weibull distribution function. Using the measured distribution of the local critical current, an experimental relation of critical current to n-value and the voltage summation model, and applying the Monte Carlo method, the overall critical current was predicted, which was in good agreement with the experimental results. Based on these results, the sample length dependence of critical current of the sample damaged by tensile stress was discussed

CURRENT-VOLTAGE CURVES FOR TREATING EFFLUENT CONTAINING HEDP: DETERMINATION OF THE LIMITING CURRENT

Directory of Open Access Journals (Sweden)

T. Scarazzato

2015-12-01

Full Text Available Abstract Membrane separation techniques have been explored for treating industrial effluents to allow water reuse and component recovery. In an electrodialysis system, concentration polarization causes undesirable alterations in the ionic transportation mechanism. The graphic construction of the current voltage curve is proposed for establishing the value of the limiting current density applied to the cell. The aim of this work was to determine the limiting current density in an electrodialysis bench stack, the function of which was the treatment of an electroplating effluent containing HEDP. For this, a system with five compartments was used with a working solution simulating the rinse waters of HEDP-based baths. The results demonstrated correlation between the regions defined by theory and the experimental data.

Protobacco Media Exposure and Youth Susceptibility to Smoking Cigarettes, Cigarette Experimentation, and Current Tobacco Use among US Youth.

Directory of Open Access Journals (Sweden)

Erika B Fulmer

Full Text Available Youth are exposed to many types of protobacco influences, including smoking in movies, which has been shown to cause initiation. This study investigates associations between different channels of protobacco media and susceptibility to smoking cigarettes, cigarette experimentation, and current tobacco use among US middle and high school students.By using data from the 2012 National Youth Tobacco Survey, structural equation modeling was performed in 2013. The analyses examined exposure to tobacco use in different channels of protobacco media on smoking susceptibility, experimentation, and current tobacco use, accounting for perceived peer tobacco use.In 2012, 27.9% of respondents were never-smokers who reported being susceptible to trying cigarette smoking. Cigarette experimentation increased from 6.3% in 6th grade to 37.1% in 12th grade. Likewise, current tobacco use increased from 5.2% in 6th grade to 33.2% in 12th grade. Structural equation modeling supported a model in which current tobacco use is associated with exposure to static advertising through perception of peer use, and by exposure to tobacco use depicted on TV and in movies, both directly and through perception of peer use. Exposure to static advertising appears to directly increase smoking susceptibility but indirectly (through increased perceptions of peer use to increase cigarette experimentation. Models that explicitly incorporate peer use as a mediator can better discern the direct and indirect effects of exposure to static advertising on youth tobacco use initiation.These findings underscore the importance of reducing youth exposure to smoking in TV, movies, and static advertising.

Dependence of critical current on sample length analyzed by the variation of local critical current bent of BSCCO superconducting composite tape

International Nuclear Information System (INIS)

Matsubayashi, H.; Mukai, Y.; Shin, J.K.; Ochiai, S.; Okuda, H.; Osamura, K.; Otto, A.; Malozemoff, A.

2008-01-01

Using the high critical current type BSCCO composite tape fabricated at American Superconductor Corporation, the relation of overall critical current to the distribution of local critical current and the dependence of overall critical current on sample length of the bent samples were studied experimentally and analytically. The measured overall critical current was described well from the distribution of local critical current and n-value of the constituting short elements, by regarding the overall sample to be composed of local series circuits and applying the voltage summation model. Also the dependence of overall critical current on sample length could be reproduced in computer satisfactorily by the proposed simulation method

Experimental investigation of flooding in air-water counter-current flow with a vertical adiabatic multi-rod bundle

International Nuclear Information System (INIS)

Chung, Bub Dong; Kim, Hho Jung; Cha, Jong Hee; Cho, Sung Jae; Chun, Moon Hyun

1991-01-01

The process of flooding phenomenon in a vertical adiabatic 3 x 3 tube bundle flow channel has been studied experimentally. A series of tests was performed, using three types of tube bundle differing only in the number of spacer grids attached, to investigate the effects of spacer grids and multi-flow channel interactions on the air-water counter-current flow limitations. Experimentally determined flooding points at various water film Reynolds numbers for three different test sections are presented in graphical form and compared with entrainment criterion for co-current flow and instability criteria. In addition, empirical flooding correlations of the Kutateladze type are obtained for each type of test section using liquid penetration data

Value Tools in Managed Care Decision Making: Current Hurdles and Future Opportunities.

Science.gov (United States)

Schafer, Jeremy; Galante, Dominic; Shafrin, Jason

2017-06-01

Organizations such as the National Comprehensive Cancer Network, American Society of Clinical Oncology, Institute for Clinical and Economic Review, and Memorial Sloan Kettering have created distinct tools to help different stakeholders assess the value of oncology treatments. However, the oncology value tools were not necessarily created for payers, and it is unclear whether payers are using these tools as part of their drug management process. To understand what value tools payers are using in oncology management and what benefits and shortcomings the tools may have from the payer perspective. A survey targeting drug coverage decision makers at health plans was conducted in August 2016. Respondents attesting to using 2 or more value tools in drug management were eligible for an additional in-depth interview to understand the respondents' perceived benefits and shortcomings of current value tools. Respondents also were asked to describe desired attributes of a hypothetical payer-centric value tool. A total of 28 respondents representing approximately 160 million commercially insured medical lives completed the survey. Twenty respondents (71%) reported using at least 1 value tool in their drug management process. Twelve respondents (43%) used at least 2 tools, and 4 respondents (14%) used at least 3 tools. A total of 6 respondents were selected for in-depth interviews. Interviewees praised value tools for advancing the discussion on drug value and incorporating clinical evidence. However, interviewees felt available value tools varied on providing firm recommendations and relevant price benchmarks. Respondents most commonly recommended the following attributes of a proposed payer-centric value framework: taking a firm position on product value; product comparisons in lieu of comparative clinical trials; web-based tool access; and tool updates at least quarterly. Interview respondents also expressed some support for allowing manipulation of inputs and inclusion of

Internal currents in PEMFC during start-up or shut-down

Energy Technology Data Exchange (ETDEWEB)

Maranzana, G.; Lottin, O.; Moyne, C.; Dillet, J.; Lamibrac, A.; Mainka, J.; Didierjean, S. [Nancy Univ. - CNRS (France). LEMTA

2010-07-01

Experiments show that the internal currents that occur during PEMFC start-up can reach up to 1 Acm{sup -2}. This is far more important than the expected order of magnitude of the current densities associated with carbon oxidation, which is only of a few mAcm{sup -2}. The predominant phenomenon that explains the internal currents is the charge and discharge of the double layer capacitances. A simple model with constant values of the electric parameters yields numerical results close to the experimental ones. It also explains the transient voltage rise (over the steady state open circuit voltage) that is sometimes observed experimentally shortly after the fuel cell start up. (orig.)

Magnitude of the current in 2D interlayer tunneling devices.

Science.gov (United States)

Feenstra, Randall M; de la Barrera, Sergio C; Li, Jun; Nie, Yifan; Cho, Kyeongjae

2018-01-15

Using the Bardeen tunneling method with first-principles wave functions, computations are made of the tunneling current in graphene/hexagonal-boron-nitride/graphene (G/h-BN/G) vertical structures. Detailed comparison with prior experimental results is made, focusing on the magnitude of the achievable tunnel current. With inclusion of the effects of translational and rotational misalignment of the graphene and the h-BN, predicted currents are found to be about 15×  larger than experimental values. A reduction in this discrepancy, to a factor of 2.5×, is achieved by utilizing a realistic size for the band gap of the h-BN, hence affecting the exponential decay constant for the tunneling.

Magnitude of the Current in Two-Dimensional Interlayer Tunneling Devices.

Science.gov (United States)

Feenstra, Randall; de la Barrera, Sergio; Li, Jun; Nie, Yifan; Cho, Kyeongjae

2018-01-02

Using the Bardeen tunneling method with first-principles wave functions, computations are made of the tunneling current in graphene / hexagonal-boron-nitride / graphene (G/h-BN/G) vertical structures. Detailed comparison with prior experimental results is made, focusing on the magnitude of the achievable tunnel current. With inclusion of the effects of translational and rotational misalignment of the graphene and the h-BN, predicted currents are found to be about 15x larger than experimental values. A reduction in this discrepancy, to a factor of 2.5x, is achieved by utilizing a realistic size for the band gap of the h-BN, hence affecting the exponential decay constant for the tunneling. © 2018 IOP Publishing Ltd.

NOAA NOS SOS, EXPERIMENTAL - Currents

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NOAA NOS SOS server is part of the IOOS DIF SOS Project. The stations in this dataset have currents data. *These services are for testing and evaluation use...

Experimental determination of the bulk temperature values in a nonisothermal flow of the chemically reacting nitrogen tetroxide

International Nuclear Information System (INIS)

Devojno, A.N.; Kolykhan, L.I.; Stepanenko, V.N.; Tverkovkin, B.E.; Uyutov, G.I.

1975-01-01

The technique and results of an experimental determination of mean mass temperatures of a cooled chemically active nitrogen tetroxide flowing in a circular tube under turbulent flow conditions are considered. The parameters range as follows: pressure-from 8.10 5 to 16.10 5 H/m 2 , flow temperature-from 140 deg to 550 deg C, Reynolds number-from 3,1.1g 5 , flow velocity-from 3.5 to 45 m/s. The gas temperature along the length of the test tube is measured with movable probe with a mixer and thermocouple in a stainless steel capillary 2mm in dia and the wall 0,2 mm thick. The mean-square deviations of measured temperature values from the predicted ones are about -0.9 and +1.8%. The obtained data show the predicted temperature values to be somewhat lower than the measured ones, the difference increasing with the distance to the test tube outlet. It may be explained by both unaccounted systematic experimental errors and errors in calculating the mean mass flow temperatures. The investigation described confirms the possibility of an experimental determination of the mean gas temperature along the cooled channel length by mean mass of a movable mixer with a single thermocouple

Experimental device, corresponding forward model and processing of the experimental data using wavelet analysis for tomographic image reconstruction applied to eddy current nondestructive evaluation

International Nuclear Information System (INIS)

Joubert, P.Y.; Madaoui, N.

1999-01-01

In the context of eddy current non destructive evaluation using a tomographic image reconstruction process, the success of the reconstruction depends not only on the choice of the forward model and of the inversion algorithms, but also on the ability to extract the pertinent data from the raw signal provided by the sensor. We present in this paper, an experimental device designed for imaging purposes, the corresponding forward model, and a pre-processing of the experimental data using wavelet analysis. These three steps implemented with an inversion algorithm, will allow in the future to perform image reconstruction of 3-D flaws. (authors)

Experimental Determination of Bed Conditions in Concentrated Pyroclastic Density Currents

Science.gov (United States)

Winner, A.; Ferrier, K.; Dufek, J.

2016-12-01

Pyroclastic density currents (PDCs) are ground-hugging mixtures of hot gas and rock that can reach temperatures > 800 oC and speeds of 200 m/s. These flows are capable of eroding and entraining the underlying bed material into the flow, which can strongly influence flow momentum, runout distance, and hazards associated with PDCs. However, the mechanism of erosion remains poorly constrained, with proposed mechanisms including under-pressure following the head of the fluidized current, force chain enhanced stresses at the bed, and discrete particle impacts and friction. The interactions between PDCs and the bed have been difficult to observe in the field, as their infrequent occurrence, opacity, and hostile environment make real-time measurement difficult. This study is aimed at obtaining a better understanding of the interactions between PDCs and the bed through a quantitative analysis of bed forces. Our experimental apparatus consists of a rotating cylindrical flume of radius 22 cm, within which gas-rich granular material flows along the interior of the cylinder as it rotates. By using a rotating cylinder, we are able to simulate long-duration flows, allowing us to observe impact forces at the bed over timescales comparable to the flow duration of natural PDCs. To measure the distribution and evolution of forces imparted by the flow on the bed, we constructed a cylindrical insert with a non-erodible bed in which we embedded force sensor arrays parallel and perpendicular to the direction of flow. To measure the forces felt by the particles in the flow, we added "smart particles" 25 to 50 mm in diameter to the flow. Each smart particle contains a three-axis accelerometer and a micro SD card enclosed in a spherical plastic casing, and possesses a density similar to that of the pumice in the experimental flow. Each smart particle also contains a three-axis magnetometer which permits its location to be tracked by means of a unique applied magnetic field. Ultimately

Mapping Ecosystem Services’ Values: Current Practice and Future Prospects

OpenAIRE

Jan Philipp Schägner; Luke Brander; Joachim Maes; Volkmar Hartje

2012-01-01

Mapping of ecosystem services' (ESS) values means valuing ESS in monetary terms across a relatively large geographical area and assessing how values vary across space. Thereby, mapping of ESS values reveals additional information as compared to traditional site-specific ESS valuation, which is beneficial for designing land use policies for maintaining ESS supply. Since the well-known article by Costanza et al. (1997), who mapped global ESS values, the number of publications mapping ESS values...

Confinement and transport properties during current ramps in the ASDEX Upgrade tokamak

Science.gov (United States)

Fable, E.; Angioni, C.; Hobirk, J.; Pereverzev, G.; Fietz, S.; Hein, T.; ASDEX Upgrade Team

2011-04-01

A detailed analysis of experimental data from the ASDEX Upgrade tokamak is carried out to shed light on the properties of confinement and transport in the current ramp-up and ramp-down phases of the plasma discharge. The experimental database is used to identify the relevant ranges of parameters explored during the ramp-up and the ramp-down. The energy confinement time observed in the two ramps displays interesting evolution, in many cases attaining different values at the same current level between ramp-up and ramp-down. The possible reasons for this behaviour are investigated. Interpretative transport simulations are used as a tool to clarify the interplay between different parameters, which are coupled in a non-linear way. In addition, a theory-based transport model is used to understand the behaviour of confinement as observed in the experiment, evidencing the role of both turbulent and neoclassical transport. Linear gyrokinetic calculations are performed to identify the relevant turbulence regime, showing that a broad range of frequencies, in the trapped electron modes (TEMs) and in the ion temperature gradient modes (ITGs) regimes, is explored during both the ramp-up and ramp-down. In the same framework, a quasi-linear model is applied to calculate the value of the local logarithmic density gradient and compare it with the experimental value. Finally, first non-linear simulations of heat transport during the current ramps are presented.

Rainforest pharmacopeia in Madagascar provides high value for current local and prospective global uses.

Directory of Open Access Journals (Sweden)

Christopher D Golden

Full Text Available Botanical diversity provides value to humans through carbon sequestration, air and water purification, and the provisioning of wild foods and ethnomedicines. Here we calculate the value of botanical ethnomedicines in a rainforest region of Madagascar, the Makira Protected Area, using a substitution method that combines replacement costs and choice modeling. The Makira watershed may comprise approximately 0.8% of global botanical diversity and possesses enormous value both in its ability to provision botanical ethnomedicines to local people and as a source of potentially novel pharmaceutical drugs for society as a whole. Approximately 241 locally-recognized species are used as ethnomedicines, including 113 agricultural or weed species. We equated each ethnomedicinal treatment to the monetary value of a comparable pharmaceutical treatment adjusted by personal preferences in perceived efficacy (rather than from known or assumed medicinal equivalency. The benefit value of these botanical ethnomedicines per individual is $5.40-7.90 per year when using the value of highly subsidized Malagasy pharmaceuticals and $100.60-287.40 when using the value of American pharmaceuticals. Using local pharmaceuticals as substitutes, the value per household is $30.24-44.30 per year, equivalent to 43-63% of median annual household income, demonstrating their local importance. Using the value of American pharmaceuticals, the amount is equivalent to 22-63% of the median annual health care expenditures for American adults under 45 in 2006. The potential for developing novel biomedicines from the Makira watershed's unique flora ranges in untapped benefit value from $0.3-5.7 billion for American pharmaceutical companies, non-inclusive of the importance of providing novel medicines and improved healthcare to society. This study provides evidence of the tremendous current local and prospective global value of botanical ethnomedicines and furthers arguments for the

Market values summary/February market review/current market data

International Nuclear Information System (INIS)

Anon.

1995-01-01

This article is the February 1995 uranium market summary. In the natural uranium and concentrates market, there were 10 deals, and the restricted value moved upward to $10.40. The unrestricted value remained fixed at $7.25. In the UF6 market, there were two deals in the restricted market, and the restricted value rose to $32.75 per kgU as UF6. The unrestricted value remained at $25.00. The restricted transaction value rose to $9.75, and the unrestricted value rose to $7.15. In the enrichment services market, there were three deals. The restricted SWU value rose to $90 per SWU, and the unrestricted value rose to $75 per SWU. Active uranium supply and active uranium demand dropped this reporting period

Spin current relaxation time in thermally evaporated pentacene films

OpenAIRE

Tani, Yasuo; Kondo, Takuya; Teki, Yoshio; Shikoh, Eiji

2017-01-01

The spin current relaxation time [tau] in thermally evaporated pentacene films was evaluated with the spin-pump-induced spin transport properties and the charge current transport properties in pentacene films. Under an assumption of a diffusive transport of the spin current in pentacene films, the zero-field mobility and the diffusion constant of holes in pentacene films were experimentally obtained to be ~8.0x10^-7 m^2/Vs and ~2.0x10^-8 m^2/s, respectively. Using those values and the previou...

Meson exchange and neutral weak currents

Energy Technology Data Exchange (ETDEWEB)

Beck, D.H. [Univ. of Illinois, Urbana, IL (United States)

1994-04-01

Measurements of parity-violating electron scattering asymmetries to determine weak neutral currents in nuclei will be effected by the presence of meson exchange currents. Present low momentum transfer calculations, based on a flavor independent framework, show these effects to be small. In general, however, as the momentum transfer increases to values typical of deep-inelastic scattering, fragmentation functions show a clear flavor dependence. It is suggested that a good experimental starting point for understanding the flavor dependence of meson production and exchange currents is the Q{sup 2} dependence of parity-violating asymmetry in inclusive single pion electroproduction. A CEBAF facility with doubled energy is necessary to approach momentum transfers where this process begins to scale.

Contribution of current carrier mobility variation to piezo-resistive effect in SmS

International Nuclear Information System (INIS)

Vasil'ev, L.N.; Kaminskij, V.V.

1999-01-01

The value of the contribution from the change in the current carriers mobility and pressure to the piezo-resistive effect value in the materials on the basis of the samarium, monosulfide is studied. The conclusion, that the value of the piezoresistance of comprehensive compression should not exceed 7x10 -3 MPa -1 at T=300 K, experimental data [ru

Normal Values and Reproducibilitiy of Electric Current Perception Threshold in Sensory Fibers

Directory of Open Access Journals (Sweden)

Reza Salman-Roghani

2006-04-01

Full Text Available Objective: Routine electrodiagnosis (EMG-NCS has some shortcomings in the evaluation of peripheral nervous system, auch as autonomous nervous system evaluation, in pure sensory radiculopathies and acute hyperesthetic stages of neuropathies. Quantitative sensory testings such as current perception threshold (CPT with electrical stimulations are suggested for above mentioned pathologies. Ttest results should be compared with a normal value of similar identical population. This study is conducted to determine normal value and reproducibility of CPT in the Iranian population. Materials & Methods: Fifty normal volunteers (32 men, 18 woman in the range of 20-40 years without exclusion criteria (such as neuro- musculoskeletal disorders, diabetes mellitus and alcoholism were recruited with simple randomized selection and CPT test was conducted on C8 (4th finger and L5 (1st Toedermatomes. To determine test’s reproducibility, 6 persons (4 men, 2 women were examined 3 times a day, 2 day per week. Collected data were analyzed to determine mean and standard deviation. Results: Normal values of CPT test was defined as one standard deviation from mean of our CPT data. These values are in C8 dermatome 2000 Hz: 2.04± 47 250 Hz: 0.75±0.25 5 Hz: 0.76±0.3 and for L5 dermatome 2000Hz: 2.83± 0.73 250 Hz: 1.24 ± 45 5Hz: 0.76± 0.3 To determine our results reproducibility and reliability, Alpha- cronbach (existed in SPSS software was used and %98.5 & 99% were obtained for C8 & L5 dermatomes respectively. Conclusion: Our findings are about C8 & L5 dermatomes which could be used as a normal Values for such dermatomes. Regarding to its good correlation with international results we can use international references as a normal Valueswith consideration of each clinic’s reproducibility should be assessed individually.

Transient current distributions in porous zinc electrodes in KOH electrolyte

Energy Technology Data Exchange (ETDEWEB)

Liu, M.B.; Yamazaki, Y.; Cook, G.M.; Yao, N.P.

1981-02-01

A zero-resistance ammeter circuit with a 10-channel operational amplifier was used to measure the current distribution during a discharge of 10 to 100 mA with simulated zinc porous electrodes in 7.24 M KOH saturated with ZnO. The reaction distribution was found to be highly nonuniform, with 70 to 78% of the charge transfer reaction completed in a depth of 0.01 cm. The high nonuniformity of the initial reaction profile was believed to be due to low conductivity of the electrolyte in the electrode pores. The current distribution changes during passivation of the electrode were experimentally obtained. A mathematical model based upon a macroscope averaging technique was used to predict the time dependence of charge transfer reaction profiles. With mathematical model, current distributions and overpotentials were predicted as a function of time for the segmented zinc electrode discharged at a current of 10 to 100 mA; for these predictions, assumed values of both precipitation rate constants for porous ZnO and diffusion coefficients for hydroxide and zincate ions were used. A gradual decrease in the specific conductivity of the pore electrolyte to 20% of the initial value during discharge yields predictions of current distributions and overpotentials in good agreement with the experimental data. The extent of reduction in the specific conductivity of the pore electrolyte implies a supersaturation of zincate of four times chemical saturation, which was been observed experimentally.At high discharge current (25 to 100 mA), the passivation behavior of the electrode has been simulated. The results of the experiments and mathematical model show that the effective reaction penetration depth is less than 0.02 cm.

A Short-Current Control Method for Constant Frequency Current-Fed Wireless Power Transfer Systems

Directory of Open Access Journals (Sweden)

Yanling Li

2017-04-01

Full Text Available Frequency drift is a serious problem in Current-Fed Wireless Power Transfer (WPT systems. When the operating frequency is drifting from the inherent Zero Voltage Switching (ZVS frequency of resonant network, large short currents will appear and damage the switches. In this paper, an inductance-dampening method is proposed to inhibit short currents and achieve constant-frequency operation. By adding a small auxiliary series inductance in the primary resonant network, short currents are greatly attenuated to a safe level. The operation principle and steady-state analysis of the system are provided. An overlapping time self-regulating circuit is designed to guarantee ZVS running. The range of auxiliary inductances is discussed and its critical value is calculated exactly. The design methodology is described and a design example is presented. Finally, a prototype is built and the experimental results verify the proposed method.

Determination of half value layer and applied voltage from emitted spectra by an X-ray tube

International Nuclear Information System (INIS)

Santos, Josilene C.; Gonzales, Alejandro H.L.; Terini, Ricardo A.; Costa, Paulo R.

2016-01-01

This work describes a method for assessment of half value layer (HVL) and peak tube voltage (kVp) applied in an X-ray tube by means of experimental X-ray spectra measured using a CdTe detector. It was assessed some parameters that can affect the evaluation of these quantities such as dead time, count rate and tube current (mA). For this study, two sets of X-ray spectra were measured: Set A), spectra measurements using Cu filters with different thicknesses (1.8 - 5.4 mm) and fixed tube current; Set B), spectra measurements keeping a fixed Cu filtration and varying tube current (0.5 - 3.0 mA). The experimental setup for the Set A spectra measurements allowed the assessment of the HVL and kVp for different count rates and dead time in the detection system, while the Set B setup allowed to assess the dependence of these quantities with the tube current. The spectrometer was energy calibrated using standard X/γ rays radioactive sources. The tube voltage values were estimated by means of experimental measured X-ray spectra, using linear regression in order to search the end point of each spectrum. The spectra correction was performed using the stripping procedure developed for the Matlab® software and the HVL values were derived from these corrected spectra. For comparison, HVL was also determined using a 30 cm"3 ion chamber and high purity Al filters. The results show that it is possible to determine the kVp with accuracy and reproducibility using spectra with dead time of up to 10%. In spite of this, the values obtained showed a deviation of up to 7 kV, for spectra measured using the same nominal tube voltage different tube current values, indicating dependence between these two parameters. (author)

Mapping ecosystem services' values : Current practice and future prospects

NARCIS (Netherlands)

Schägner, Jan Philipp; Brander, Luke; Maes, Joachim; Hartje, Volkmar

Mapping of ecosystem services' (ESS) values means valuing ESS in monetary terms across a relatively large geographical area and assessing how values vary across space. Thereby, mapping of ESS values reveals additional information as compared to traditional site-specific ESS valuation, which is

Axial mercury segregation in direct current operated low-pressure argon-mercury gas discharge: Part I. Experimental

NARCIS (Netherlands)

Gielen, J.W.A.M.; de Groot, S.; Dijk, van J.; Mullen, van der J.J.A.M.

2004-01-01

Due to cataphoresis, axial segregation of mercury will occur when the gas discharge of a fluorescent lamp is operated by means of a direct current. A consequence of this is a non-uniform axial luminance distribution along the lamp. To determine the degree of axial mercury segregation experimentally,

Market values summary/January market review/current market data

International Nuclear Information System (INIS)

Anon.

1994-01-01

This article is the January 1994 uranium market summary. In the natural uranium and concentrates market, there were only three deals reported. The restricted value dropped to $9.50, while the unrestricted value remained steady at $7.00. There was only one UF6 trade reported, and both the restricted and unrestricted values decreased (to $30.15 and $24.50 respectively). The restricted transaction value remained at $7.15, and the unrestricted value declined to $10.00. In the enrichment services market, only one deal was concluded. In this market, the restricted value increased to $85.00 per SWU, and the unrestricted value remained unchanged at $68.00 per SWU. Both active uranium supply and active uranium demand decreased slightly during this period

Market values summary/September market review/current market data

International Nuclear Information System (INIS)

Anon.

1994-01-01

This article is the September 1994 uranium market summary. In the concentrates and conversion market, there were four deals. The unrestricted value decreased slightly to $7.00, and the restricted value decreased to $9.05. In the UF6 market, there was a single transaction. Both the restricted and the unrestricted values decreased ($29.00 and $24.25 respectively). The restricted transaction value was unchanged at $9.15, while the unrestricted value decreased to $7.10. In the enrichment services market, long-term contracting picked up and there were two deals in the spot market. Restricted values dropped to $84.00 per SWU, while the unrestricted value remained constant at $67.00 per SWU. Active uranium supply increased, while active uranium demand decreased

Recent Advances in Simulation of Eddy Current Testing of Tubes and Experimental Validations

Science.gov (United States)

Reboud, C.; Prémel, D.; Lesselier, D.; Bisiaux, B.

2007-03-01

Eddy current testing (ECT) is widely used in iron and steel industry for the inspection of tubes during manufacturing. A collaboration between CEA and the Vallourec Research Center led to the development of new numerical functionalities dedicated to the simulation of ECT of non-magnetic tubes by external probes. The achievement of experimental validations led us to the integration of these models into the CIVA platform. Modeling approach and validation results are discussed here. A new numerical scheme is also proposed in order to improve the accuracy of the model.

The e3value ontology for value networks : Current state and future directions

NARCIS (Netherlands)

Weigand, Hans

2016-01-01

Meeting changing customer demands and business opportunities in a connected world makes it necessary for organizations to constantly innovate by means of value-creating collaborations. The goal of value modeling is to support the exploration of new business models from an economic point of view. The

Market values summary/December market review/current market data

International Nuclear Information System (INIS)

Anon.

1994-01-01

This article is the December 1993 uranium market summary. During this period, there were six deals in the restricted concentrates market and none in the unrestricted market. The restricted value dropped slightly to $9.85 per pound U3O8, while the unrestricted market rose slightly to $7.00. The UF6 market was also slow, with a slight decrease in the restricted UF6 value to $31.00 and no change in the unrestricted value ($24.00). The unrestricted transaction value was $7.15 per pound U3O8, and the restricted value was $10.25. In the enrichment services market, the unrestricted SWU value remained fixed at $68.00 per SWU, while the unrestricted value increased by a dollar to $84.00 per SWU. Active uranium supply decreased, while active demand increased

Performance of lead-acid batteries. Experimental study and discharge process modelling; Desempenho de baterias chumbo-acido. Estudo experimental e modelamento do processo de descarga

Energy Technology Data Exchange (ETDEWEB)

Barreto, G; Bottura, C P [Universidade Estadual de Campinas, SP (Brazil); Oliveira, M G [Universidade Estadual de Campinas, SP (Brazil). Inst. de Quimica

1985-12-31

Commercial lead-acid batteries performance when continuously discharge is valued in this work. The model relating battery capacity and discharge current is confirmed through the analysis of experimental results relating voltage to time for various discharge currents. Such model was determined for the tested batteries and can be interpreted in terms of diffusional limitations and plate passivation. (author). 2 figs., 1 tab., 12 refs

Experimentally obtained values of electric field of an atmospheric pressure plasma jet impinging on a dielectric surface

NARCIS (Netherlands)

Sobota, A.; Guaitella, O.; Garcia-Caurel, E.

2013-01-01

We report on experimentally obtained values of the electric field magnitude on a dielectric surface induced by an impinging atmospheric pressure plasma jet. The plasma plume was striking the dielectric surface at an angle of 45¿, at 5mm from the surface measured at the axis of the jet. The results

Experimental Study on the Influence of AC Stray Current on the Cathodic Protection of Buried Pipe

Directory of Open Access Journals (Sweden)

Qingmiao Ding

2016-01-01

Full Text Available The size of the damaged area of the coating and its position on the pipeline impacted the cathodic protection potential, and there was a damaged area of the greatest impact value. When damaged area was 300 mm2, the IR drop was the largest, and this situation could easily lead to inadequate protection; when the parallel spacing between pipeline and interference source was unchanged, the measured value curves of cathodic protection potential presented “U” shaped trend with the increasing stray current interference intensity. Under certain parallel spacing between pipeline and interference source, high alternating stray current intensity would cause serious negative offsets, so that the overprotection of the pipeline occurred, and make the coating crack; there was a parallel threshold length. When less than the threshold, the pipe-ground potential increases rapidly with the parallel length increasing. In order to judge whether a pipeline was interference by AC stray current and the risk of stray current corrosion, we should make a comprehensive analysis of the cathodic protection energizing potential, the switch-off potential, AC pipe-soil potential, IR drops, and so on.

Current drive efficiency requirements for an attractive steady-state reactor

Energy Technology Data Exchange (ETDEWEB)

Tonon, G

1994-12-31

The expected values of the figure of merit and the electrical efficiency of various non-inductive current drive methods are considered. The main experimental results achieved today with neutral beams and radiofrequency systems are summarized. Taking into account the simplified energy flow diagram of a steady state reactor, the figure of merit and the electrical efficiency values which are necessary in order to envisage an attractive steady-state reactor are determined. These values are compared to the theoretical predictions. (author). 16 refs., 11 figs., 2 tabs.

Current drive efficiency requirements for an attractive steady-state reactor

International Nuclear Information System (INIS)

Tonon, G.

1994-01-01

The expected values of the figure of merit and the electrical efficiency of various non-inductive current drive methods are considered. The main experimental results achieved today with neutral beams and radiofrequency systems are summarized. Taking into account the simplified energy flow diagram of a steady state reactor, the figure of merit and the electrical efficiency values which are necessary in order to envisage an attractive steady-state reactor are determined. These values are compared to the theoretical predictions. (author). 16 refs., 11 figs., 2 tabs

Re/creating entrepreneurs of the self: discourses of worker and employee 'value' and current vocational rehabilitation practices.

Science.gov (United States)

Fadyl, Joanna; McPherson, Kathryn; Nicholls, David

2015-05-01

Vocational rehabilitation for people experiencing work disability is a social practice often situated within health services, but the social and political drivers and effects of this practice are rarely critically analysed in health research or policy. In this study we used a Foucauldian theoretical perspective to analyse the ways in which current vocational rehabilitation practices in New Zealand re/produce notions of worker and employee 'value', and how different approaches to vocational rehabilitation deploy current discourses about value. We also consider the subject positions produced through these different approaches and the identities and actions they make possible for people experiencing work disability. The analysis showed that notions about the importance of worker and employee value in a job market are pervasive in vocational rehabilitation, and reflect wider societal discourses. However, the deployment of those discourses in different approaches to vocational rehabilitation practice are diverse, producing different opportunities and constraints for people experiencing disability. We argue that an examination of these various opportunities and constraints at the level of practice approaches is important, as considerable time and resources are allocated to developing solutions to help those who do not thrive in the current systems, yet we rarely critique the premises on which the systems are based. © 2015 The Authors. Sociology of Health & Illness © 2015 Foundation for the Sociology of Health & Illness/John Wiley & Sons Ltd.

5 CFR Appendix A to Subpart C of... - Present Value Conversion Factors for Earlier Commencing Date of Annuities of Current and Former...

Science.gov (United States)

2010-01-01

... 5 Administrative Personnel 2 2010-01-01 2010-01-01 false Present Value Conversion Factors for Earlier Commencing Date of Annuities of Current and Former Spouses of Deceased Separated Employees A...—Present Value Conversion Factors for Earlier Commencing Date of Annuities of Current and Former Spouses of...

Neoclassical current effects in neutral-beam-heated tokamak discharges

International Nuclear Information System (INIS)

Hogan, J.T.

1981-01-01

There is a long-standing prediction from neoclassical theory that strong contributions to the toroidal current should be driven by friction between trapped and passing particles when βsub(pol) exceeds root (R/a) in a tokamak. A number of neutral-beam heating experiments can now produce such parameters, and it is of interest to calculate the behaviour which should occur in this regime to determine the feasibility of using such a 'bootstrap' current as a steady-state tokamak current source. It is found that the neoclassical current should be large enough to reverse the external loop voltage for typical experimental parameters (ISX-B, in particular) in cases where the total current is fixed and to produce a detectable excess of total current above the pre-programmed (demand) value in cases where the loop voltage is regulated. Other manifestations of such a current should be either: a sharp rise in the central q-value (producing a cessation of internal m=1 and m=2 MHD activity), with an enhancement by two orders of magnitude of ion thermal conductivity (due to the formation of a hollow current density profile and a consequent drop in local values of the poloidal magnetic field in the central plasma region), or an enhanced tendency for disruption (arising from magnetic reconnection in hollow-profile equilibria). Since these gross manifestations are absent in a wide range of experiments on the Impurity Study Experiment (ISX-B), as reported earlier, the conclusion is that the neoclassical current, if present, can have a value no larger than 25% of its theoretically calculated value. Since the neoclassical particle (Ware) pinch is strongly related to the neoclassical current in the theory (Onsager reciprocity), the existence of the particle pinch is thus called into question. (author)

Oxidation of organic pollutants on BDD anodes using modulated current electrolysis

International Nuclear Information System (INIS)

Panizza, M.; Kapalka, Agnieszka; Comninellis, Ch.

2008-01-01

In this paper, a theoretical model is presented for organic pollutants mineralization at high current efficiency (close to 100%) and low energy consumption on boron-doped diamond electrodes. The model is formulated for a perfect mixed electrochemical reactor operated as a batch recirculation system under multiple current steps, in which the applied current is adjusted during the electrolysis to be close to the limiting value. An experimental validation with the anodic oxidation of 3,4,5-trihydroxybenzoic acid is also provided. The results have shown that multiple current steps electrolysis and continuous current control allowed obtaining high oxidation rate and current efficiency

Oxidation of organic pollutants on BDD anodes using modulated current electrolysis

Energy Technology Data Exchange (ETDEWEB)

Panizza, M. [Department of Chemical and Process Engineering, University of Genoa, P.le J.F. Kennedy 1, 16129 Genova (Italy)], E-mail: marco.panizza@unige.it; Kapalka, Agnieszka [Institute of Chemical Sciences and Engineering, Ecole Polytechnique Federale de Lausanne (EPFL), CH-1015 Lausanne (Switzerland); Comninellis, Ch. [Institute of Chemical Sciences and Engineering, Ecole Polytechnique Federale de Lausanne (EPFL), CH-1015 Lausanne (Switzerland)], E-mail: christos.comninellis@epfl.ch

2008-01-01

In this paper, a theoretical model is presented for organic pollutants mineralization at high current efficiency (close to 100%) and low energy consumption on boron-doped diamond electrodes. The model is formulated for a perfect mixed electrochemical reactor operated as a batch recirculation system under multiple current steps, in which the applied current is adjusted during the electrolysis to be close to the limiting value. An experimental validation with the anodic oxidation of 3,4,5-trihydroxybenzoic acid is also provided. The results have shown that multiple current steps electrolysis and continuous current control allowed obtaining high oxidation rate and current efficiency.

The Way of Reducing Current Values in Optical Ground Wires at Asymmetrical Faults on Overhead Transmission Lines

Directory of Open Access Journals (Sweden)

Egamnazarov Georgiy

2016-12-01

Full Text Available Given the fact that the installing costs of an optical ground wire on overhead lines directly depend on its cross-section, which in turn depends on the level of fault current it should withstand, in order to reduce these current values in the optical ground wire, I suggested performing its isolated descents from the end towers of the line with its transition to an optical cable. The research was carried out on the example of a 500 kV overhead line in the National Electric Power Grid. The Method of Symmetrical Components for calculating asymmetrical fault currents was not used; therefore, calculations were carried out on the base of presenting the line as a multi-wire system for the considered case as a five-wire system (optical ground wire, steel ground wire, and three phase wires. Such approach allows taking into account the initial asymmetry of the line parameters and modeling any kind of asymmetrical faults. The analyses of calculated results were performed. The conclusive evidence that the optical ground wire isolated descents from the end towers of the line give the possibility of reducing the level of maximal fault current distribution values in it and therefore its cross section, is presented.

Improvement of patient return electrodes in electrosurgery by experimental investigations and numerical field calculations.

Science.gov (United States)

Golombeck, M A; Dössel, O; Raiser, J

2003-09-01

Numerical field calculations and experimental investigations were performed to examine the heating of the surface of human skin during the application of a new electrode design for the patient return electrode. The new electrode is characterised by an equipotential ring around the central electrode pads. A multi-layer thigh model was used, to which the patient return electrode and the active electrode were connected. The simulation geometry and the dielectric tissue parameters were set according to the frequency of the current. The temperature rise at the skin surface due to the flow of current was evaluated using a two-step numerical solving procedure. The results were compared with experimental thermographical measurements that yielded a mean value of maximum temperature increase of 3.4 degrees C and a maximum of 4.5 degrees C in one test case. The calculated heating patterns agreed closely with the experimental results. However, the calculated mean value in ten different numerical models of the maximum temperature increase of 12.5 K (using a thermodynamic solver) exceeded the experimental value owing to neglect of heat transport by blood flow and also because of the injection of a higher test current, as in the clinical tests. The implementation of a simple worst-case formula that could significantly simplify the numerical process led to a substantial overestimation of the mean value of the maximum skin temperature of 22.4 K and showed only restricted applicability. The application of numerical methods confirmed the experimental assertions and led to a general understanding of the observed heating effects and hotspots. Furthermore, it was possible to demonstrate the beneficial effects of the new electrode design with an equipotential ring. These include a balanced heating pattern and the absence of hotspots.

Turbulent current heating of dense plasma

International Nuclear Information System (INIS)

Suprunenko, V.A.; Sukhomlin, E.A.; Volkov, E.D.; Perepelkij, N.F.

1976-01-01

Based upon experimental results an attempt is made for systematizing and analysing conditions of experiments in anomalous resistance and turbulent heating of a plasma. The extensive program of such investigations aims at a direct practical study on quasistationary heating and plasma containment in magnetic traps. It has been shown that in real conditions turbulent heating turns out to be a far more complicated phenomenon than that described within the framework of theories developed so far. It has been established that the phenomenon alters in the transition through the critical values of electric and magnetic fields. This makes it possible to separate four characteristic experimental regimes. For all the regimes the stabilization of the electron current drift rate is typical. On the basis of the experimental results obtained an explanation is given of the sporadic character of the ultrathermal radiation in a quasistationary discharge

Current Needs for the Experimental Investigation of the CHF Phenomenon Relevant to LWR Core Conditions

International Nuclear Information System (INIS)

Le Corre, J.M.

2009-01-01

The current achievements and needs toward the investigation, understanding and mechanistic prediction of the Critical Heat Flux (CHF) event, under PWR and BWR core conditions, are addressed in this paper. It is shown that, even when using advanced 3-D CFD simulation tools, the current approach to CHF mechanistic modeling has serious limitations. This is mainly due to the lack of information regarding the relevant two-phase flow pattern(s) (in particular near the heated wall) and associated mechanisms (at the meso and micro-scale) leading to the CHF event. Areas of current experimental needs are identified in order to address these shortcomings. In addition, the use of 1-D and 3-D numerical tools to mechanistically predict the CHF is discussed. It is shown that 3-D two-phase CFD codes may not be superior to 1-D codes without proper consideration of relevant constitutive relations. (author)

Experimental Investigations on Combustion Behaviors of Live PVC Cables

Science.gov (United States)

Wang, Liufang; Zhang, Jiaqing; Zhang, Bosi; Liu, Min; Fan, Minghao; Li, Qiang

2018-03-01

This paper investigated the combustion behaviors of live PVC cables with overload currents experimentally. The smoke coefficient of released smoke and the released gas concentration were examined. The results indicate that the combustion of live PVC cables can be divided into four stages, i.e., core exposed with a little smoke, obvious flame, maximum smoke and smoke depress. For most cases, using blue laser is better than using rad laser, since the extinction coefficient of the rad laser was larger than that of the blue laser. The response time of the detection of the released typical gases due to cable pyrolysis decreased and the peak values of the typical gases increased with the overload currents. In addition, the time to reach the peak value of gas concentration also decreased with the overload currents.

Experimental investigation of droplet separation in a horizontal counter-current air/water stratified flow

International Nuclear Information System (INIS)

Gabriel, Stephan Gerhard

2015-01-01

A stratified counter-current two-phase gas/liquid flow can occur in various technical systems. In the past investigations have mainly been motivated by the possible occurrence of these flows in accident scenarios of nuclear light water-reactors and in numerous applications in process engineering. However, the precise forecast of flow parameters, is still challenging, for instance due to their strong dependency on the geometric boundary conditions. A new approach which uses CFD methods (Computational Fluid Dynamics) promises a better understanding of the flow phenomena and simultaneously a higher scalability of the findings. RANS methods (Reynolds Averaged Navier Stokes) are preferred in order to compute industrial processes and geometries. A very deep understanding of the flow behavior and equation systems based on real physics are necessary preconditions to develop the equation system for a reliable RANS approach with predictive power. Therefore, local highly resolved, experimental data is needed in order to provide and validate the required turbulence and phase interaction models. The central objective of this work is to provide the data needed for the code development for these unsteady, turbulent and three-dimensional flows. Experiments were carried out at the WENKA facility (Water Entrainment Channel Karlsruhe) at the Karlsruhe Institute of Technology (KIT). The work consists of a detailed description of the test-facility including a new bended channel, the measurement techniques and the experimental results. The characterization of the new channel was done by flow maps. A high-speed imaging study gives an impression of the occurring flow regimes, and different flow phenomena like droplet separation. The velocity distributions as well as various turbulence values were investigated by particle image velocimetry (PIV). In the liquid phase fluorescent tracer-particles were used to suppress optical reflections from the phase surface (fluorescent PIV, FPIV

A Comparison between Value-Added School Estimates and Currently Used Metrics of School Accountability in California

Science.gov (United States)

Fagioli, Loris P.

2014-01-01

This study compared a value-added approach to school accountability to the currently used metrics of accountability in California of Adequate Yearly Progress (AYP) and Academic Performance Index (API). Five-year student panel data (N?=?53,733) from 29 elementary schools in a large California school district were used to address the research…

Experimental study of matrix carbon field-emission cathodes and computer aided design of electron guns for microwave power devices, exploring these cathodes

International Nuclear Information System (INIS)

Grigoriev, Y.A.; Petrosyan, A.I.; Penzyakov, V.V.; Pimenov, V.G.; Rogovin, V.I.; Shesterkin, V.I.; Kudryashov, V.P.; Semyonov, V.C.

1997-01-01

The experimental study of matrix carbon field-emission cathodes (MCFECs), which has led to the stable operation of the cathodes with current emission values up to 100 mA, is described. A method of computer aided design of TWT electron guns (EGs) with MCFEC, based on the results of the MCFEC emission experimental study, is presented. The experimental MCFEC emission characteristics are used to define the field gain coefficient K and the cathode effective emission area S eff . The EG program computes the electric field upon the MCFEC surface, multiplies it by the K value and uses the Fowler Nordheim law and the S eff value to calculate the MCFEC current; the electron trajectories are computed as well. copyright 1997 American Vacuum Society

Improving implementation of evidence-based practice in mental health service delivery: protocol for a cluster randomised quasi-experimental investigation of staff-focused values interventions.

Science.gov (United States)

Williams, Virginia; Oades, Lindsay G; Deane, Frank P; Crowe, Trevor P; Ciarrochi, Joseph; Andresen, Retta

2013-07-02

There is growing acceptance that optimal service provision for individuals with severe and recurrent mental illness requires a complementary focus on medical recovery (i.e., symptom management and general functioning) and personal recovery (i.e., having a 'life worth living'). Despite significant research attention and policy-level support, the translation of this vision of healthcare into changed workplace practice continues to elude. Over the past decade, evidence-based training interventions that seek to enhance the knowledge, attitudes, and skills of staff working in the mental health field have been implemented as a primary redress strategy. However, a large body of multi-disciplinary research indicates disappointing rates of training transfer. There is an absence of empirical research that investigates the importance of worker-motivation in the uptake of desired workplace change initiatives. 'Autonomy' is acknowledged as important to human effectiveness and as a correlate of workplace variables like productivity, and wellbeing. To our knowledge, there have been no studies that investigate purposeful and structured use of values-based interventions to facilitate increased autonomy as a means of promoting enhanced implementation of workplace change. This study involves 200 mental health workers across 22 worksites within five community-managed organisations in three Australian states. It involves cluster-randomisation of participants within organisation, by work site, to the experimental (values) condition, or the control (implementation). Both conditions receive two days of training focusing on an evidence-based framework of mental health service delivery. The experimental group receives a third day of values-focused intervention and 12 months of values-focused coaching. Well-validated self-report measures are used to explore variables related to values concordance, autonomy, and self-reported implementation success. Audits of work files and staff work samples

Experimental determination of isotope enrichment factors – bias from mass removal by repetitive sampling

DEFF Research Database (Denmark)

Buchner, Daniel; Jin, Biao; Ebert, Karin

2017-01-01

to account for mass removal and for volatilization into the headspace. In this study we use both synthetic and experimental data to demonstrate that the determination of ε-values according to current correction methods is prone to considerable systematic errors even in well-designed experimental setups....... Application of inappropriate methods may lead to incorrect and inconsistent ε-values entailing misinterpretations regarding the processes underlying isotope fractionation. In fact, our results suggest that artifacts arising from inappropriate data evaluation might contribute to the variability of published ε...

Current decay and stability in SPICA, ch. 7

International Nuclear Information System (INIS)

Bobeldijk, C.; Hoekzema, J.A.; Mimura, M.; Oepts, D.; Oomens, A.A.M.

1976-08-01

The equilibrium and stability of the toroidal screw pinch has been studied in SPICA at q-values around 1.5. This regime is of interest because theory predicts stability there for rather high values of β. The experimental results show that plasmas with peak β-values of 0.2 (Tsub(e) = 60 eV, nsub(e) = 5x10 21 /m 3 ) can be contained in stable equilibrium during 100 μs. Low-current decay rates indicate a well-developed force-free field profile in a sufficiently hot dilute plasma region outside the main column. In unstable discharges, m-2 modes appear. These discharges are characterized by faster decay and larger eccentricity of the plasma column

Study on classical and excess eddy currents losses of Terfenol-D

Energy Technology Data Exchange (ETDEWEB)

Talebian, Soheil; Hojjat, Yousef [Department of Mechanical Engineering, Tarbiat Modares University, Tehran (Iran, Islamic Republic of); Ghodsi, Mojtaba [Department of Mechanical and Industrial Engineering, Sultan Qaboos University, Muscat (Oman); Karafi, Mohammad Reza [Department of Mechanical Engineering, Tarbiat Modares University, Tehran (Iran, Islamic Republic of)

2015-08-15

In the present paper, classical and excess eddy currents losses of Terfenol-D are studied and effects of magnetic field frequency, peak of magnetic flux density and diameter of Terfenol-D on the eddy currents losses are investigated. To provide reliable data for the purpose of the paper, an experimental laboratory is fabricated and used to obtain major and minor hysteresis loops of Terfenol-D at different frequencies. In theoretical study, initially an analytical model based on uniform distribution of magnetic flux is developed which yields to calculation of classical eddy currents losses. Then, another eddy currents model based on non-uniform distribution of magnetic flux and nonlinear diffusion of electromagnetic fields is presented. The difference between output values of the two models is identified as excess eddy currents losses. Obtained results show that the values of excess losses are generally larger than classical losses and applying just classical model leads to wrong calculation of actual value of eddy currents losses. For the results obtained from two above models, empirical models with respect to the magnetic field frequency and the peak value of magnetic flux density are achieved which can predict the eddy currents losses precisely. To validate the empirical relations, experiments are repeated at a new frequency and values of power losses calculated from analytical equations are compared with the predicted values of the empirical models. The results point towards possibility to use the obtained empirical relations in order to calculate the classical and excess eddy currents losses of Terfenol-D at the frequencies below 200 Hz and different values of magnetic flux density. - Highlights: • Classical eddy currents loss of Terfenol-D is studied using Maxwell's laws. • Excess eddy currents loss of Terfenol-D is studied using Mayergoyz nonlinear model. • Effects of Terfenol-D geometry on the eddy currents losses are investigated. • Power

Experimental and analytical study on vibration control effects of eddy-current tuned mass dampers under seismic excitations

Science.gov (United States)

Lu, Zheng; Huang, Biao; Zhang, Qi; Lu, Xilin

2018-05-01

Eddy-current tuned mass dampers (EC-TMDs) are non-contacting passive control devices and are developed on the basis of conventional tuned mass dampers. They comprise a solid mass, a stiffness element, and a damping element, wherein the damping mechanism originates from eddy currents. By relative motion between a non-magnetic conductive metal and a permanent magnet in a dynamic system, a time-varying magnetic field is induced in the conductor, thereby generating eddy currents. The eddy currents induce a magnetic field with opposite polarity, causing repulsive forces, i.e., damping forces. This technology can overcome the drawbacks of conventional tuned mass dampers, such as limited service life, deterioration of mechanical properties, and undesired additional stiffness. The experimental and analytical study of this system installed on a multi-degree-of-freedom structure is presented in this paper. A series of shaking table tests were conducted on a five-story steel-frame model with/without an EC-TMD to evaluate the effectiveness and performance of the EC-TMD in suppressing the vibration of the model under seismic excitations. The experimental results show that the EC-TMD can effectively reduce the displacement response, acceleration response, interstory drift ratio, and maximum strain of the columns under different earthquake excitations. Moreover, an analytical method was proposed on the basis of electromagnetic and structural dynamic theories. A comparison between the test and simulation results shows that the simulation method can be used to estimate the response of structures with an EC-TMD under earthquake excitations with acceptable accuracy.

Large area dispenser cathode applied to high current linac

International Nuclear Information System (INIS)

Yang Anmin; China Academy of Engineering Physics, Mianyang; Wu Dengxue; Liu Chenjun; Xia Liansheng; Wang Wendou; Zhang Kaizhi

2005-01-01

The paper introduced a dispenser cathode (411 M) which was 55 mm in diameter. A 200 kV long pulsed power generator with 2 μs flattop based on Marx-PEN and system with heat and voltage insulation were built. A 52 A space charge limited current was gained, when the temperature was 1165 degree C and the filament current was 18 A on the cathode and the voltage of the pulse was 75 kV at the cathode test stand. Experimental results show that the current values are consistent with the numerical simulation. The experiment reveals that the deflated gas will influence the cathode emission ability. (authors)

Alternating-current ohmic heating in a helical stellarator

International Nuclear Information System (INIS)

Funato, Yasuyuki; Kitajima, Sumio; Watanabe, Hiroshige

1984-01-01

A toroidal plasma is generated successively by an alternating-current discharge in a helical or non-planar torus, and is confined quasi-stationarily by a longitudinal magnetic field with a high rotational transform angle. The particle confinement time obtained experimentally is estimated to be 3-10 ms, which is compared with theoretical values for this system, and is much larger than the time of pulse interval of the plasma production. (author)

Capacitance measurement of Josephson tunnel junctions with microwave-induced dc quasiparticle tunneling currents

International Nuclear Information System (INIS)

Hamasaki, K.; Yoshida, K.; Irie, F.; Enpuku, K.

1982-01-01

The microwave response of the dc quasiparticle tunneling current in Josephson tunnel junctions, where the Josephson current is suppressed by an external magnetic field, has been studied quantitatively in order to clarify its characteristics as a probe for the measurement of the junction capacitance. Extensive experiments for both small and long junctions are carried out for distinguishing between microwave behaviors of lumped and distributed constant junctions. It is shown that the observed voltage dependence of the dc quasiparticle tunneling current modified by an applied rf field is in good agreement with a theoretical result which takes into account the influence of the microwave circuit connected to the junction. The comparison between theory and experiment gives the magnitude of the internal rf field in the junction. Together with the applied rf field, this internal rf field leads to the junction rf impedance which is dominated by the junction capacitance in our experimental condition. In the case of lumped junctions, this experimental rf impedance is in reasonable agreement with the theoretical one with the junction capacitance estimated from the Fiske step of the distributed junction fabricated on the same substrate; the obtained ratio of the experimental impedance to the theoretical one is approximately 0.6--1.7. In the case of distributed junctions, however, experimental values of their characteristic impedances are approximately 0.2--0.3 of theoretical values calculated by assuming the one-dimensional junction model and taking account of the standing-wave effect in the junction

An experimental investigation to evaluate the heating value of palm oil waste by calorimetry. Paper no. IGEC-1-040

International Nuclear Information System (INIS)

Supeni, E.E.; Megat Mohd, M.H.; Mohd Sapuan, S.; Nor Maria, A.; Ismail, M.Y.; Thoguluva, R.V.; Chuah, T.G.

2005-01-01

A palm oil mill produces palm oil and kernel palm oil as main products and biomass residue (fiber and shell). This excess biomass residue can be used as fuel in boilers to meet energy and process heat demand in the industries. Quality of the palm oil waste (POW) is characterized by low fixed carbon and relatively high moisture content which may affect the heating value (HV). By applying the principle of calorimetry, a bomb calorimeter is utilized to evaluate the heating value of POW. From the experimental results, it is found that higher heating value (HHV) varies with the moisture content (MC) and it is observed as a function of MC. (author)

Ion current prediction model considering columnar recombination in alpha radioactivity measurement using ionized air transportation

International Nuclear Information System (INIS)

Naito, Susumu; Hirata, Yosuke; Izumi, Mikio; Sano, Akira; Miyamoto, Yasuaki; Aoyama, Yoshio; Yamaguchi, Hiromi

2007-01-01

We present a reinforced ion current prediction model in alpha radioactivity measurement using ionized air transportation. Although our previous model explained the qualitative trend of the measured ion current values, the absolute values of the theoretical curves were about two times as large as the measured values. In order to accurately predict the measured values, we reinforced our model by considering columnar recombination and turbulent diffusion, which affects columnar recombination. Our new model explained the considerable ion loss in the early stage of ion diffusion and narrowed the gap between the theoretical and measured values. The model also predicted suppression of ion loss due to columnar recombination by spraying a high-speed air flow near a contaminated surface. This suppression was experimentally investigated and confirmed. In conclusion, we quantitatively clarified the theoretical relation between alpha radioactivity and ion current in laminar flow and turbulent pipe flow. (author)

Current algebra and πΔ photoproduction

International Nuclear Information System (INIS)

Chaichian, M.; Nelipa, N.F.

1980-01-01

By using the improved technique of current algebra, sum rules for the process γ+N→π+Δ(1236) are obtained. The estimated value for the coupling constant π + Δ + Δ ++ is g 2 /4π=105 in good agreement with old experimental determinations and as well with other theoretical predictions, but in discrepancy with a recent partial wave analysis of the latest bubble chamber data. This might put doubts on the recent data (analysis), since otherwise all the theoretical evaluations should suffer from a common shortcoming. (author)

Experimental investigation of localized stress-induced leakage current distribution in gate dielectrics using array test circuit

Science.gov (United States)

Park, Hyeonwoo; Teramoto, Akinobu; Kuroda, Rihito; Suwa, Tomoyuki; Sugawa, Shigetoshi

2018-04-01

Localized stress-induced leakage current (SILC) has become a major problem in the reliability of flash memories. To reduce it, clarifying the SILC mechanism is important, and statistical measurement and analysis have to be carried out. In this study, we applied an array test circuit that can measure the SILC distribution of more than 80,000 nMOSFETs with various gate areas at a high speed (within 80 s) and a high accuracy (on the 10-17 A current order). The results clarified that the distributions of localized SILC in different gate areas follow a universal distribution assuming the same SILC defect density distribution per unit area, and the current of localized SILC defects does not scale down with the gate area. Moreover, the distribution of SILC defect density and its dependence on the oxide field for measurement (E OX-Measure) were experimentally determined for fabricated devices.

Experimental measurements of the eddy current signal due to a flawed, conducting half space

International Nuclear Information System (INIS)

Long, S.A.; Toomsawasdi, S.; Zaman, A.J.M.

1984-01-01

This chapter reports on an experimental investigation in which the change in impedance of a practical multi-turn eddy current coil near a conducting half space is measured as a function of the conductivity and the lift-off distance. The results are compared in a qualitative fashion with the analytical results for a single-turn coil. Measurements are also made of the change in impedance due to a small void in the conducting half space as a function of both its depth and radial position. The results indicate that, at least in a qualitative fashion, the precisely derived analytical solutions adequately predict the general behavior of the change in complex impedance of an eddy current coil above a conducting ground plane as a function of lift-off distance. It is determined that the effect of a sub-surface void on the change in inductance of the test coil correlates well with theoretical calculations

Harem: Hardwood lumber remanufacturing program for maxmizing value based on size, grade and current market prices

Science.gov (United States)

C.J. Schwehm; P. Klinkhachorn; Charles W. McMillin; Henry A. Huber

1990-01-01

This paper describes an expert system computer program which will determine the optimum way to edge and trim a hardwood board so as to yield the highest dollar value based on the grade, size of each board, and current market prices. The program uses the Automated Hardwood Lumber Grading Program written by Klinkhachorn, et al. for determining the grade of each board...

Experimental results on one-pion neutral current reaction in all channels induced by antineutrinos at CERN PS

CERN Document Server

Erriquez, O; Bullock, F W; Cavalli, D; Engel, J P; Fogli-Muciaccia, M T; Gamba, D; Guyonnet, J L; Halsteinslid, A; Henderson, R C W; Huss, D; Jones, T W; Marzari-Chiesa, A; Myklebost, K; Natali, S; Nuzzo, S; Paty, M; Pullia, A; Riccati, L; Riester, J L; Rognebakke, A; Rollier, M; Romero, A

1980-01-01

Single pion production, in antineutrino-nucleon interactions via the neutral current, has been studied in the bubble chamber Gargamelle, filled with propane. Complete analysis of the secondaries, including pi /sup 0/'s, has allowed a detailed study of all channels. After background and nuclear corrections, results are obtained which can be interpreted in terms of isospin structure of the neutral weak current and of the Salam-Weinberg angle. Agreement is found with the currently accepted value of sin/sup 2/ theta /sub w/ and the data suggest an important contribution of I=/sup 3///sub 2/ final states. (11 refs).

Value encounters - Modeling and analyzing co-creation of value

NARCIS (Netherlands)

Weigand, H.; Godart, C.; Gronau, N.; Sharma, S.; Canals, G.

2009-01-01

Recent marketing and management literature has introduced the concept of co-creation of value. Current value modeling approaches such as e3-value focus on the exchange of value rather than co-creation. In this paper, an extension to e3-value is proposed in the form of a “value encounter”. Value

Value encounters : Modelling and analyzing co-creation of value

NARCIS (Netherlands)

Weigand, H.; Jayasinghe Arachchig, J.

2009-01-01

Recent marketing and management literature has introduced the concept of co-creation of value. Current value modeling approaches such as e3-value focus on the exchange of value rather than co-creation. In this paper, an extension to e3-value is proposed in the form of a “value encounter”. Value

Influence of ambient humidity on the current delivered by air-vented ionization chambers revisited

International Nuclear Information System (INIS)

Poirier, Aurelie; Douysset, Guilhem

2006-01-01

The influence of ambient humidity on the current delivered by a vented ionization chamber has been re-investigated. A Nucletron 077.091 well-type chamber together with a 192 Ir HDR brachytherapy source was enclosed in a climatic test chamber and the current was recorded for various humidity values. Great care has been taken for the design of the experimental setup in order to obtain reliable measurements of currents and humidity values inside the chamber active volume. A ±0.35% linear variation of the measured currents has been observed over a common range of humidities. This result is larger than the expected variation. No formal explanation of such a discrepancy has been found yet, however the present results could lead to a set of recommendations

Influence of ambient humidity on the current delivered by air-vented ionization chambers revisited

Energy Technology Data Exchange (ETDEWEB)

Poirier, Aurelie; Douysset, Guilhem [Laboratoire National Henri Becquerel-LNE, CEA Saclay 91191 Gif-sur-Yvette (France)

2006-10-07

The influence of ambient humidity on the current delivered by a vented ionization chamber has been re-investigated. A Nucletron 077.091 well-type chamber together with a {sup 192}Ir HDR brachytherapy source was enclosed in a climatic test chamber and the current was recorded for various humidity values. Great care has been taken for the design of the experimental setup in order to obtain reliable measurements of currents and humidity values inside the chamber active volume. A {+-}0.35% linear variation of the measured currents has been observed over a common range of humidities. This result is larger than the expected variation. No formal explanation of such a discrepancy has been found yet, however the present results could lead to a set of recommendations.

Market values summary/April market review/current market data

International Nuclear Information System (INIS)

Anon.

1995-01-01

This article is the April 1995 uranium market summary. Overall market activity during this period was low, with five deals in the concentrates market, two deals in the long-term natural uranium market, and three deals in the spot enrichment market. There were no spot trades in the UF6 or conversion market. The restricted and unrestricted exchange values were $11.60 and $7.35 respectively. The restricted and unrestricted UF6 values were $36.00 and $25.50, and the restricted and unrestricted transaction values were $10.30 and $7.25. Active uranium supply rose, and active demand fell

Experimental verification of the gas pumping theory within fission ionisation chambers

International Nuclear Information System (INIS)

Bartlett, A.C.

1975-01-01

Experimental verification of a theory for gas loss from in-core ionization chambers is reported. A value of the gas pressure within an irradiated miniature fission chamber was derived indirectly by use of published data on Townsend first coefficient/field across the detector as a function of field/pressure. In practice the voltage corresponding to 10% current multiplication is measured. From the current saturation characteristics measured on the detector during irradiation, the change in gas pressure as a function of fluence was derived and compared to theoretically predicted values. Within the limited accuracy obtainable substantial agreement between measurement and theory is obtained. (O.T.)

Electron cyclotron resonance heating and current drive

Energy Technology Data Exchange (ETDEWEB)

Fidone, I.; Castejon, F.

1992-07-01

A brief summary of the theory and experiments on electron- cyclotron heating and current drive is presented. The general relativistic formulation of wave propagation and linear absorption is considered in some detail. The O-mode and the X-mode for normal and oblique propagation are investigated and illustrated by several examples. The experimental verification of the theory in T-10 and D- III-D is briefly discussed. Quasilinear evolution of the momentum distribution and related applications as, for instance, non linear wave, damping and current drive, are also considered for special cases of wave frequencies, polarization and propagation. In the concluding section we present the general formulation of the wave damping and current drive in the absence of electron trapping for arbitrary values of the wave frequency. (Author) 13 refs.

Electron - cyclotron resonance heating and current drive

International Nuclear Information System (INIS)

Fidone, I.; Castejon, F.

1992-01-01

A brief summary of the theory and experiments on electron- cyclotron heating and current drive is presented. The general relativistic formulation of wave propagation and linear absorption is considered in some detail. The O-mode and the X-mode for normal and oblique propagation are investigated and illustrated by several examples. The experimental verification of the theory in T-10 and D- III-D is briefly discussed. Quasilinear evolution of the momentum distribution and related applications as, for instance, non linear wave, damping and current drive, are also considered for special cases of wave frequencies, polarization and propagation. In the concluding section we present the general formulation of the wave damping and current drive in the absence of electron trapping for arbitrary values of the wave frequency. (Author) 13 refs

Electron-cyclotron resonance heating and current drive

International Nuclear Information System (INIS)

Filone, I.

1992-01-01

A brief summary of the theory and experiments on electron-cyclotron heating and current drive is presented. the general relativistic formulation of wave propagation and linear absorption is considered in some detail. The O-mode and the X-mode for normal and oblique propagation are investigated and illustrated by several examples. The experimental verification of the theory in T-10 and D-III-D is briefly discussed. Quasilinear evolution of the momentum distribution and related applications as, for instance, non linear wave damping and current drive, are also considered for special cases of wave frequencies, polarization and propagation. In the concluding section we present the general formulation of the wave damping and current drive in the absence of electron trapping for arbitrary values of the wave frequency. (author) 8 fig. 13 ref

Digital peak current mode control with adaptive slope compensation for DC-DC converters

DEFF Research Database (Denmark)

Andersen, Karsten Holm; Nymand, Morten

2017-01-01

performance and stability of current mode control. The presented method adapt to DC-DC converter operating conditions by estimating the rising and falling inductor current slopes, to apply a current slope compensation value to obtain a constant quality factor. The experimental results verifies the theoretical......This paper presents an adaptive slope compensation method for peak current mode control of digital controlled DC-DC converters, which controls the quality factor of the complex conjugated poles at half the switching frequency. Using quality factor control enables optimization of the dynamic...

Langmuir probe characteristic in a current - carrying magnetized plasma

International Nuclear Information System (INIS)

Stanojevic, M.; Cercek, M.; Gyergyek, T.

1995-01-01

Experimental investigation of the Langmuir probe characteristic is a magnetized plasma with an electron current along the magnetic field direction shows that the standard procedure for determination of the electron temperature and plasma density, which is applicable in a current - free magnetized plasma, gives erroneous results for these plasma parameters. However, more precise values of the plasma parameters can be calculated from the ion saturation currents and electron temperatures obtained with that procedure for two opposite orientations of the one - sided planar probe collecting surface with respect to the direction of the electron drift. With the existing theoretical models only the order of magnitude of the electron drift velocity can be accurately determined from the measured electron saturation currents for the two probe orientations. (author)

Current in heavy-current planar diode with discrete emission surface

International Nuclear Information System (INIS)

Belomyttsev, S.Ya.; Korovin, S.D.; Pegel', I.V

1999-01-01

Dependence of current in a high-current planar diode on the size of emission centres was studied. Essential effect of emission surface microstructure on the current value in the planar diode was demonstrated. It was determined that if the distance between the emitter essentially exceeded their size then current dependence on the ratio of size to the value of the diode gap was an exponential function with 3/2 index. Current dependence on voltage obeyed the exponential law with 3/2 index up to higher voltage values in the planar diode with discrete emission surface in contrast to the case of a planar diode with homogeneous emission surface [ru

Experimental studies of the quench behaviour of MgB{sub 2} superconducting wires for fault current limiter applications

Energy Technology Data Exchange (ETDEWEB)

Ye Lin [Interdisciplinary Research Center (IRC) in Superconductivity, Cavendish Laboratory/Department of Engineering, University of Cambridge, J J Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Majoros, M [Laboratories for Applied Superconductivity and Magnetism, Ohio State University, Columbus, OH 43210 (United States); Campbell, A M [Interdisciplinary Research Center (IRC) in Superconductivity, Cavendish Laboratory/Department of Engineering, University of Cambridge, J J Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Coombs, T [Interdisciplinary Research Center (IRC) in Superconductivity, Cavendish Laboratory/Department of Engineering, University of Cambridge, J J Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Astill, D [Interdisciplinary Research Center (IRC) in Superconductivity, Cavendish Laboratory/Department of Engineering, University of Cambridge, J J Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Harrison, S [Scientific Magnetics, Culham Science Centre, Culham, Abingdon, Oxfordshire OX14 3DB (United Kingdom); Husband, M [Strategic Research Center (SRC)-Electrical Engineering, Rolls-Royce plc, Derby DE24 8BJ (United Kingdom); Rindfleisch, M [Hyper Tech Research Inc., Columbus, OH 43212 (United States); Tomsic, M [Hyper Tech Research Inc., Columbus, OH 43212 (United States)

2007-07-15

Various MgB{sub 2} wires with different sheath materials provided by Hyper Tech Research Inc., have been tested in the superconducting fault current limiter (SFCL) desktop tester at 24-26 K in a self-field. Samples 1 and 2 are similarly fabricated monofilamentary MgB{sub 2} wires with a sheath of CuNi, except that sample 2 is doped with SiC and Mg addition. Sample 3 is a CuNi sheathed multifilamentary wire with Cu stabilization and Mg addition. All the samples with Nb barriers have the same diameter of 0.83 mm and superconducting fractions ranging from 15% to 27% of the total cross section. They were heat-treated at temperatures of 700 deg. C for a hold time of 20-40 min. Current limiting properties of MgB{sub 2} wires subjected to pulse overcurrents have been experimentally investigated in an AC environment in the self-field at 50 Hz. The quench currents extracted from the pulse measurements were in a range of 200-328 A for different samples, corresponding to an average engineering critical current density (J{sub e}) of around 4.8 x 10{sup 4} A cm{sup -2} at 25 K in the self-field, based on the 1 {mu}V cm{sup -1} criterion. This work is intended to compare the quench behaviour in the Nb-barrier monofilamentary and multifilamentary MgB{sub 2} wires with CuNi and Cu/CuNi sheaths. The experimental results can be applied to the design of fault current limiter applications based on MgB{sub 2} wires.

Market values summary/October market review/current market data

International Nuclear Information System (INIS)

Anon.

1994-01-01

This article is the October uranium market summary. During this period, volume increased to 2.2 Mlb U3O8 on the spot concentrates market. The unrestricted and restricted exchange values remained steady at $7.00 and $9.05 per pound U3O8 respectively. There were two UF6 deals during this period, and with supply more than adequate to meet the demand, the restricted UF6 price remained unchanged at $29.00 per kgU as UF6. The unrestricted value increased slightly to $24.50. The conversion value was unchanged, and the enrichment services market/prices weakened. Both active supply and demand decreased during this period

Experimental Study of Current Discharge Behavior and Hard X-ray Anisotropy by APF Plasma Focus Device

Science.gov (United States)

Habibi, M.; Amrollahi, R.; Attaran, M.

2009-03-01

Amirkabir (APF) is a new Mather-type plasma focus device (16 kV, 36 μf, and 115 nH). In this work we present some experimental results as variation of discharge current signal respect to applied voltage at the optimum pressure, focusing time of plasma versus gas pressure, and variations of current discharge with different insulator sleeve dimensions. As we prospected optimum pressure tending to increase as we tried to higher voltage levels. The time taken by the current sheath to lift-off the insulator surface and therefore quality of pinched plasma depends on the length of the insulator sleeve. The results show that the insulator diameter can influence on pinch quality. Behavior of hard X-ray (HXR) signals with the pressure and also anisotropy of HXR investigated by the use of two scintillation detectors. The distribution of HXR intensity shows a large anisotropy with a maximum intensity between 22.5° and 45° and also between -22.5° and -67.5°.

Eddy currents in pulsed field measurements

International Nuclear Information System (INIS)

Kuepferling, M.; Groessinger, R.; Wimmer, A.; Taraba, M.; Scholz, W.

2002-01-01

Full text: One problem of pulsed field magnetometry is an error in magnetization, which appears in measurements of conducting samples. This error is due to eddy currents induced by a time varying field. To allow predictions how eddy currents exert influence on the hysteresis loop, systematic experimental and theoretical studies of pulsed field measurements of metallic samples were performed. The theoretical studies include analytical calculations as well as numerical ones using a 2D finite element software. In the measurements three physical parameters have been varied: i) the conductivity of the sample by using two different materials, in this case technical Cu and Al ii) size and shape of the sample by using cylinders, spheres and cuboids iii) the pulse duration of the external field by changing the capacitor battery from 8mF ( =9.1ms) to 24mF ( =15.7ms). The time dependence of the external field corresponds with a pulsed damped harmonic oscillation with a maximum value of 5.2T. The samples were studied in the as cast state (after machining) as well as after heat treatment. Theoretical calculations showed not only good agreement with the absolute values of the measured eddy current m agnetization , they also gave an explanation of the shape of the eddy current hysteresis and the dependence of the eddy current 'magnetization' on parameters as pulse duration of the external field and conductivity of the sample. (author)

Differences between signal currents for both polarities of applied voltages on cavity ionization chambers

International Nuclear Information System (INIS)

Takata, N.

2000-01-01

It is necessary to obtain precise values of signal currents for the measurement of exposure rates for gamma rays with cavity ionization chambers. Signal currents are usually expected to have the same absolute values for both polarities of applied voltages. In the case of cylindrical cavity ionization chambers, volume recombination loss of ion pairs depends on the polarity of the applied voltage. This is because the values of mobility are different for positive and negative ions. It was found, however, that values of signal currents from a cylindrical ionization chamber change slightly more with a negative than with a positive applied voltage, even after being corrected for volume recombination loss. Moreover, absolute values of saturation currents, which are obtained by extrapolation of correction of initial recombination and diffusion loss, were larger for the negative than for the positive applied voltage. It is known from an experiment with parallel plate ionization chambers that when negative voltage is applied to the repeller electrode, the saturated signal current decreases with an increase in the applied voltage. This is because secondary electrons are accelerated and the stopping power of air for these electrons decreases. When positive voltage is applied, the reverse is true. The effects of acceleration and deceleration of secondary electrons by the electric field thus seem to cause a tendency opposite to the experimental results on the signal currents from cylindrical ionization chambers. The experimental results for the cylindrical ionization chamber can be explained as follows. When negative voltage is applied, secondary electrons are attracted to the central (collecting) electrode. Consequently, the path length of the trajectories of these secondary electrons in the ionization volume increases and signal current increases. The energy gain from the electric field by secondary electrons which stop in the ionization chamber also contributes to the

Experimental testing and modelling of a resistive type superconducting fault current limiter using MgB2 wire

International Nuclear Information System (INIS)

Smith, A C; Pei, X; Oliver, A; Husband, M; Rindfleisch, M

2012-01-01

A prototype resistive superconducting fault current limiter (SFCL) was developed using single-strand round magnesium diboride (MgB 2 ) wire. The MgB 2 wire was wound with an interleaved arrangement to minimize coil inductance and provide adequate inter-turn voltage withstand capability. The temperature profile from 30 to 40 K and frequency profile from 10 to 100 Hz at 25 K were tested and reported. The quench properties of the prototype coil were tested using a high current test circuit. The fault current was limited by the prototype coil within the first quarter-cycle. The prototype coil demonstrated reliable and repeatable current limiting properties and was able to withstand a potential peak current of 372 A for one second without any degradation of performance. A three-strand SFCL coil was investigated and demonstrated scaled-up current capacity. An analytical model to predict the behaviour of the prototype single-strand SFCL coil was developed using an adiabatic boundary condition on the outer surface of the wire. The predicted fault current using the analytical model showed very good correlation with the experimental test results. The analytical model and a finite element thermal model were used to predict the temperature rise of the wire during a fault. (paper)

Investigation of the LH wave energy conversion and current drive efficiency in the HT-7 tokamak

International Nuclear Information System (INIS)

Chen, Z.Y.; Wan, B.N.; Shi, Y.J.; Lin, S.Y.; Hu, L.Q.; Asif, M.

2005-01-01

Lower hybrid current drive (LHCD) plasmas in the presence of DC electric filed have been investigated based on Karney-Fisch theory in the HT-7 tokamak. The relatively small scatter in the experimental data with various values of waveguide phasing and lower hybrid power, when plotted in the Karney-Fisch diagram, confirms that a reasonable theoretical interpretation is possible for the HT-7 data. The full non-inductively current drive efficiencies are obtained by fitting the experimental data to the theoretical curve. The efficiency strongly depends on the lower hybrid wave phase velocity

Experimental study on vortex-induced motions of a semi-submersible with square columns and pontoons at different draft conditions and current incidences

Directory of Open Access Journals (Sweden)

Mingyue Liu

2017-05-01

Full Text Available The Vortex-induced Motions (VIM phenomenon of semi-submersibles is relevant for the fatigue life of moorings and risers. Model tests regarding the VIM behavior of a semi-submersible with four square columns were conducted in order to investigate the effects of the current incidence and the aspect ratio of the immerged column. The experimental results show that the largest transverse amplitudes are around 70% of the column width at 30° and 45° incidences in a range of reduced velocities from 5 to 8 when the aspect ratio of the immerged column is 1.90. The largest yaw motion occurs at 0° incidence with the peak value around 4.5°. Similar characteristics of the VIM response are observed for the semi-submersible with aspect ratios of 1.90 and 1.73. When the aspect ratio decreases 50% to 0.87, 30% decrease in the peak transverse amplitudes can be seen.

A Combined Experimental and Finite Element Analysis Method for the Estimation of Eddy-Current Loss in NdFeB Magnets

Directory of Open Access Journals (Sweden)

Radu Fratila

2014-05-01

Full Text Available NdFeB permanent magnets (PMs are widely used in high performance electrical machines, but their relatively high conductivity subjects them to eddy current losses that can lead to magnetization loss. The Finite Element (FE method is generally used to quantify the eddy current loss of PMs, but it remains quite difficult to validate the accuracy of the results with complex devices. In this paper, an experimental test device is used in order to extract the eddy current losses that are then compared with those of a 3D FE model.

A combined experimental and finite element analysis method for the estimation of eddy-current loss in NdFeB magnets.

Science.gov (United States)

Fratila, Radu; Benabou, Abdelkader; Tounzi, Abdelmounaïm; Mipo, Jean-Claude

2014-05-14

NdFeB permanent magnets (PMs) are widely used in high performance electrical machines, but their relatively high conductivity subjects them to eddy current losses that can lead to magnetization loss. The Finite Element (FE) method is generally used to quantify the eddy current loss of PMs, but it remains quite difficult to validate the accuracy of the results with complex devices. In this paper, an experimental test device is used in order to extract the eddy current losses that are then compared with those of a 3D FE model.

Comparison of standardized uptake values measured on F-NaF PET/CT scans using three different tube current intensities.

Science.gov (United States)

Valadares, Agnes Araujo; Duarte, Paulo Schiavom; Woellner, Eduardo Bechtloff; Coura-Filho, George Barberio; Sapienza, Marcelo Tatit; Buchpiguel, Carlos Alberto

2015-01-01

To analyze standardized uptake values (SUVs) using three different tube current intensities for attenuation correction on (18)FNaF PET/CT scans. A total of 254 (18)F-NaF PET/CT studies were analyzed using 10, 20 and 30 mAs. The SUVs were calculated in volumes of interest (VOIs) drawn on three skeletal regions, namely, right proximal humeral diaphysis (RH), right proximal femoral diaphysis (RF), and first lumbar vertebra (LV1) in a total of 712 VOIs. The analyses covered 675 regions classified as normal (236 RH, 232 RF, and 207 LV1). Mean SUV for each skeletal region was 3.8, 5.4 and 14.4 for RH, RF, and LV1, respectively. As the studies were grouped according to mAs value, the mean SUV values were 3.8, 3.9 and 3.7 for 10, 20 and 30 mAs, respectively, in the RH region; 5.4, 5.5 and 5.4 for 10, 20 and 30 mAs, respectively, in the RF region; 13.8, 14.9 and 14.5 for 10, 20 and 30 mAs, respectively, in the LV1 region. The three tube current values yielded similar results for SUV calculation.

Current experimental situation in heavy-ion reactions

International Nuclear Information System (INIS)

Scott, D.K.

1978-06-01

A detailed survey of the present experimental situation in heavy-ion physics is presented. The discussion begins by considering the simple excitation of discrete states in elastic scattering, transfer, and compound-nucleus reactions; it then turns to more drastic perturbations of the nucleus high in the continuum through fusion, fission, and deeply inelastic scattering, and concludes with the (possibly) limiting asymptotic phenomena of relativistic heavy-ion collisions. 138 figures, 5 tables, 451 references

'I think it will eventually be done away with': Attitudes among healthcare professionals towards the current system of animal experimentation.

Science.gov (United States)

Dignon, Andrée

2016-08-01

This article describes a study of attitudes to the current system of animal experimentation (for the production of health interventions) among 52 UK healthcare professionals. These healthcare professionals participated in three separate focus groups (of 18, 17 and 17 participants) and were invited to respond to the question 'what is your opinion about the current system of animal testing?' The study focused specifically on their views of the current system (rather than their views of animal testing in general). The healthcare professionals were critical of the current system, particularly with regard to regulation, secrecy, validity, unnecessary suffering and welfare. © The Author(s) 2014.

Towards accurate T-3He Q-value

Energy Technology Data Exchange (ETDEWEB)

Eronen, Tommi; Hoecker, Martin; Ketter, Jochen; Streubel, Sebastian; Blaum, Klaus [Max-Planck Institut fuer Kernphysik, Heidelberg (Germany); Van Dyck, Robert S. Jr. [Department of Physics, University of Washington, Seattle, WA (United States)

2013-07-01

Great efforts have been put forward to determine the neutrino mass from tritium β decay. The most prominent experimental setup, KATRIN, is expected to deliver an upper limit to the neutrino mass that is one order of magnitude more stringent than the current value by measuring the endpoint and the shape of the β spectrum of the tritium decay. The endpoint energy (assuming zero neutrino mass) can also be deduced from the Q-value of the decay by measuring the mass difference of tritium and the daughter {sup 3}He using high-resolution mass spectrometry. Such a measurement would give an excellent, independent calibration point for the KATRIN experiment to deduce its systematics. Our mass-difference measurement utilizes the Tritium- Helium double Penning trap (THe-Trap) setup. Based on the anharmonic cyclotron frequency determination method pioneered at the University of Washington, Seattle, precision at the level of 1 part in 10{sup 11} in the T/{sup 3}He mass ratio is expected. In this contribution, I describe the motivation, the principle, current status, and expectations of the experiment.

Modeling of the Direct Current Generator Including the Magnetic Saturation and Temperature Effects

Directory of Open Access Journals (Sweden)

Alfonso J. Mercado-Samur

2013-11-01

Full Text Available In this paper the inclusion of temperature effect on the field resistance on the direct current generator model DC1A, which is valid to stability studies is proposed. First, the linear generator model is presented, after the effect of magnetic saturation and the change in the resistance value due to temperature produced by the field current are included. The comparison of experimental results and model simulations to validate the model is used. A direct current generator model which is a better representation of the generator is obtained. Visual comparison between simulations and experimental results shows the success of the proposed model, because it presents the lowest error of the compared models. The accuracy of the proposed model is observed via Modified Normalized Sum of Squared Errors index equal to 3.8979%.

Calculated fraction of an incident current pulse that will be accelerated by an electron linear accelerator and comparisons with experimental data

International Nuclear Information System (INIS)

Alsmiller, R.G. Jr.; Alsmiller, F.S.; Lewis, T.A.

1986-05-01

In a series of previous papers, calculated results obtained using a one-dimensional ballistic model were presented to aid in the design of a prebuncher for the Oak Ridge Electron Linear Accelerator. As part of this work, a model was developed to provide limits on the fraction of an incident current pulse that would be accelerated by the existing accelerator. In this paper experimental data on this fraction are presented and the validity of the model developed previously is tested by comparing calculated and experimental data. Part of the experimental data is used to fix the physical parameters in the model and then good agreement between the calculated results and the rest of the experimental data is obtained

Experimental study of intensive electron beam scattering in melting channel

International Nuclear Information System (INIS)

Balagura, V.S.; Kurilko, V.I.; Safronov, B.G.

1988-01-01

Multiple scattering of an intensive electron beam at 28 keV energy passing through a melting channel in iron targets is experimentally studied. The dependence of scattering on the melting current value is established. The material density in the channel on the basis of the binary collision method is evaluated. It is shown that these density values are of three orders less than the estimations made on the basis of the data on energy losses of electrons in the channel. 6 refs.; 4 figs

Dynamic response of HTS composite tapes to pulsed currents

International Nuclear Information System (INIS)

Meerovich, V; Sokolovsky, V; Prigozhin, L; Rozman, D

2006-01-01

Dynamic voltage-current characteristics of an HTS Ag/BiSCCO composite tape are studied both experimentally and theoretically. The tape is subjected to pulsed currents with different shapes and magnitudes and voltage traces are measured using the four-point method with different locations of potential taps on the sample surface. Clockwise and anticlockwise hysteresis loops are obtained for the same sample depending on the location of the potential taps. The dynamic characteristics deviate substantially from the DC characteristic, especially in the range of low voltages where a criterion for the critical current value is usually chosen (1-10 μV cm -1 ). The critical current determined from dynamic characteristics and its change with the pulse magnitude depend on the location of the potential taps and on the curve branch chosen for the critical current determination (ascending or descending). The theoretical analysis is based on a model of the magnetic flux diffusion into a composite tape for a superconductor described by the flux creep characteristic. Numerical simulation based on this model gives results in good agreement with the experimental ones and explains the observed peculiarities of the dynamic characteristics of HTS composite tapes. The difference between the magnetic diffusion into a tape and a slab is discussed

Research of Influence of Noise Pollution on the Value of the Threshold Current Tangible

Science.gov (United States)

Khanzhina, Olga; Sidorov, Alexander; Zykina, Ekaterina

2017-12-01

Stable safety while working on electrical installations can be achieved by following the rules of the electrical safety. Today maximum permissible levels of touch voltage and electric current flow through any part of a person’s body are established by Russian Federation GOST system 12.1.038-82. Unfortunately, recommended by International Electrotechnical Commission (IEC) maximum allowable amount of electric current and voltage level do not take into account interaction between said electric current and other physical factors; noise, in particular. The influence of sound frequency and its pressure level on body resistance has been proven earlier in thesis by V.V. Katz. Studies of the noise effects on the value of the threshold current tangible have been renewed in laboratories of Life Safety Department in South Ural State University. To obtain reliable results, testing facility that includes anechoic chamber, sources of simulated voltages and noise and a set of recording instruments was designed and built. As a rule, noise influence on electrotechnical personnel varies depending on noise level or/and the duration of its impact. According to modern theories, indirect noise influence on various organs and systems through central nervous system has to be considered. Differential evaluation of noise pollution and its correlation with emerged effects can be obtained with the usage of the dose approach. First of all, there were conducted studies, in which frequency of the applied voltage (f) was to 50 Hz. Voltages and currents that caused sensations before and during 97 dB noise affections were measured. Obtained dependence led to questioning previous researches results of the necessity of reducing the amperage of tripping protection devices. At the same time electrical resistance changes of human body were being studied. According to those researches, no functional dependence between fluctuations in the magnitude of the resistance of human body to electric current flow

Experimental comparison of the critical ionization velocity in atomic and molecular gases

International Nuclear Information System (INIS)

Axnaes, I.

1978-08-01

The critical ionization velocity usub(c) of Ne, Kr, Xe, Cl 2 , O 2 , CO, CO 2 , NH 3 and H 2 O is investigated experimentally in a coaxial plasma gun. Together with experimental data obtained in earlier experiments the present results make it possible to make a systematic comparison between the critical ionization velocity for atomic and molecular gases. It is found that atomic and molecular gases tend to have values of critical ionization velocity which are respectively smaller and larger than the theoretical values. The current dependence of usub(c) is found to be different for atomic and molecular gases. A number of atomic and molecular processes relevant to the experiment are discussed

Clinical experimentation with aerosol antibiotics: current and future methods of administration

Directory of Open Access Journals (Sweden)

Zarogoulidis P

2013-10-01

Full Text Available Paul Zarogoulidis,1,2 Ioannis Kioumis,1 Konstantinos Porpodis,1 Dionysios Spyratos,1 Kosmas Tsakiridis,3 Haidong Huang,4 Qiang Li,4 J Francis Turner,5 Robert Browning,6 Wolfgang Hohenforst-Schmidt,7 Konstantinos Zarogoulidis1 1Pulmonary Department, G Papanikolaou General Hospital, Aristotle University of Thessaloniki, Thessaloniki, Greece; 2Department of Interventional Pneumology, Ruhrlandklinik, West German Lung Center, University Hospital, University Duisburg-Essen, Essen, Germany; 3Cardiothoracic Surgery Department, Saint Luke Private Hospital of Health Excellence, Thessaloniki, Greece; 4Department of Respiratory Diseases, Shanghai Hospital/First Affiliated Hospital of the Second Military Medical University, Shanghai, People’s Republic of China; 5Pulmonary Medicine, University of Nevada School of Medicine, National Supercomputing Center for Energy and the Environment University of Nevada, Las Vegas, NV, USA; 6Pulmonary and Critical Care Medicine, Interventional Pulmonology, National Naval Medical Center, Walter Reed Army Medical Center, Bethesda, MD, USA; 7II Medical Department, Regional Clinic of Coburg, University of Wuerzburg, Coburg, Germany Abstract: Currently almost all antibiotics are administered by the intravenous route. Since several systems and situations require more efficient methods of administration, investigation and experimentation in drug design has produced local treatment modalities. Administration of antibiotics in aerosol form is one of the treatment methods of increasing interest. As the field of drug nanotechnology grows, new molecules have been produced and combined with aerosol production systems. In the current review, we discuss the efficiency of aerosol antibiotic studies along with aerosol production systems. The different parts of the aerosol antibiotic methodology are presented. Additionally, information regarding the drug molecules used is presented and future applications of this method are discussed

Experimental study on a wide range of wave and current conditions of the WEPTOS Wave Energy Converter

DEFF Research Database (Denmark)

Pecher, Arthur; Kofoed, Jens Peter

This report presents the results of an experimental study that was performed on small scale model that was a replication of the full-scale Weptos WEC intended for DanWEC. The tests were performed in the circular basin at FloWave at Edinburgh University in October 2014. The laboratory facilities h...... the capabilities to have simultaneously currents and waves from any possible direction and also to produce advanced wave specifications....

Filling of a Salt-withdrawal Minibasin on the Continental Slope by Turbidity Currents: Experimental study

Science.gov (United States)

Violet, J.; Evans, C.; Sheets, B.; Paola, C.; Pratson, L.; Parker, G.

2001-12-01

We report on the transport and deposition of sediment by turbidity currents in an experimental basin designed to model salt-withdrawal minibasins found along the northern continental slope of the Gulf of Mexico. The experiment was performed in two stages in the subsiding EXperimental EarthScape facility (XES) at St. Anthony Falls Laboratory, University of Minnesota. Stage I consisted of 15 turbidity-current events in the following sequence: one 36-minute continuous event, six 1.85-minute small pulses, one 3.8-minute large pulse, six more small pulses, one more large pulse, and finally one more continuous event. The continuous events and the small pulses had a flow discharge of 1.5 liters/s and the large pulse had a flow discharge of 4.5 liters/s. The flows all had a volume concentration of sediment of 0.05. The sediment comprised three grades of silica with nominal diameters of 20 microns (45%), 45 microns (40%) and 110 microns (15%). The basin subsided continuously during Stage I. Stage II consisted of the same sequence of events as Stage I, but with no further subsidence. The sand content was eliminated during the latter part of Stage II. The deposit was imaged as it developed during the experiment using high-frequency sonar. The sonar records show indications of incipient self-channelization as well as clear erosion, bypass, and deposition. Erosion was promoted by large pulse events and the absence of sand. The deposit shows well developed lamination and normal grading.

Evanescently Coupled Rectangular Microresonators in Silicon-on-Insulator with High Q-Values: Experimental Characterization

Directory of Open Access Journals (Sweden)

Manuel Mendez-Astudillo

2017-04-01

Full Text Available We report on evanescently coupled rectangular microresonators with dimensions up to 20 × 10 μm2 in silicon-on-insulator in an add-drop filter configuration. The influence of the geometrical parameters of the device was experimentally characterized and a high Q value of 13,000 was demonstrated as well as the multimode optical resonance characteristics in the drop port. We also show a 95% energy transfer between ports when the device is operated in TM-polarization and determine the full symmetry of the device by using an eight-port configuration, allowing the drop waveguide to be placed on any of its sides, providing a way to filter and route optical signals. We used the FDTD method to analyze the device and e-beam lithography and dry etching techniques for fabrication.

Current Parental Depression and Offspring Perceived Self-Competence: A Quasi-Experimental Examination

Science.gov (United States)

Class, Quetzal A.; D’Onofrio, Brian M.; Singh, Amber L.; Ganiban, Jody M.; Spotts, E. L.; Lichtenstein, Paul; Reiss, David; Neiderhiser, Jenae M.

2013-01-01

A genetically-informed, quasi-experimental design was used to examine the genetic and environmental processes underlying associations between current parental depressive symptoms and offspring perceived self-competence. Participants, drawn from a population-based Swedish sample, were 852 twin pairs and their male (52%) and female offspring aged 15.7 ± 2.4 years. Parental depressive symptoms were measured using the Center for Epidemiological Studies Depression scale. Offspring perceived self-competence was measured using a modified Harter Perceived Competence Scale. Cousin comparisons and Children of Twins (CoT) designs suggested that associations between maternal depressive symptoms and offspring perceived self-competence were due to shared genetic/environmental liability. The mechanism responsible for father-offspring associations, however, was independent of genetic factors and of extended-family environmental factors, supporting a causal inference. Thus, mothers and fathers may impact offspring perceived self-competence via different mechanisms and unmeasured genetic and environmental selection factors must be considered when studying the intergenerational transmission of cognitive vulnerabilities for depression. PMID:22692226

Current parental depression and offspring perceived self-competence: a quasi-experimental examination.

Science.gov (United States)

Class, Quetzal A; D'Onofrio, Brian M; Singh, Amber L; Ganiban, Jody M; Spotts, E L; Lichtenstein, Paul; Reiss, David; Neiderhiser, Jenae M

2012-09-01

A genetically-informed, quasi-experimental design was used to examine the genetic and environmental processes underlying associations between current parental depressive symptoms and offspring perceived self-competence. Participants, drawn from a population-based Swedish sample, were 852 twin pairs and their male (52 %) and female offspring aged 15.7 ± 2.4 years. Parental depressive symptoms were measured using the Center for Epidemiological Studies Depression scale. Offspring perceived self-competence was measured using a modified Harter Perceived Competence Scale. Cousin comparisons and Children of Twins designs suggested that associations between maternal depressive symptoms and offspring perceived self-competence were due to shared genetic/environmental liability. The mechanism responsible for father-offspring associations, however, was independent of genetic factors and of extended family environmental factors, supporting a causal inference. Thus, mothers and fathers may impact offspring perceived self-competence via different mechanisms and unmeasured genetic and environmental selection factors must be considered when studying the intergenerational transmission of cognitive vulnerabilities for depression.

Experimental Investigation on Electric Current-Aided Laser Stake Welding of Aluminum Alloy T-Joints

Directory of Open Access Journals (Sweden)

Xinge Zhang

2017-11-01

Full Text Available In the present study, aluminum alloy T-joints were welded using the laser stake-welding process. In order to improve the welding quality of the T-joints, an external electric current was used to aid the laser stake-welding process. The effects of the process parameters on the weld morphology, mechanical properties, and microstructure of the welded joints were analyzed and discussed in detail. The results indicate that the aided electric current should be no greater than a certain maximum value. Upon increasing the aided electric current, the weld width at the skin and stringer faying surface obviously increased, but there was an insignificant change in the penetration depth. Furthermore, the electric current and pressing force should be chosen to produce an expected weld width at the faying surface, whereas the laser power and welding speed should be primarily considered to obtain an optimal penetration depth. The tensile shear specimens failed across the faying surface or failed in the weld zone of the skin. The specimens that failed in the weld of the skin could resist a higher tensile shear load compared with specimens that failed across the faying surface. The microstructural observations and microhardness results demonstrated that the tensile shear load capacity of the aluminum alloy welded T-joint was mainly determined by the weld width at the faying surface.

Market Values Summary/December Market Review/Current Market Data

International Nuclear Information System (INIS)

Anon.

1995-01-01

A summary of financial data for the 1994 uranium market is provided. Price ranges for the restricted and unrestricted markets, conversion, and separative work are listed. Detailed transactions are listed for enrichment services, enriched uranium product, sales and loans, uranium supply and demand, conversion supply and demand, and separative work supply and demand. Previous 6-month and yearly values are noted. A table of market values expressed in selected currencies is also provided

All inequality is not equal: children correct inequalities using resource value

Science.gov (United States)

Shaw, Alex; Olson, Kristina R.

2013-01-01

Fairness concerns guide children's judgments about how to share resources with others. However, it is unclear from past research if children take extant inequalities or the value of resources involved in an inequality into account when sharing with others; these questions are the focus of the current studies. In all experiments, children saw an inequality between two recipients—one had two more resources than another. What varied between conditions was the value of the resources that the child could subsequently distribute. When the resources were equal in value to those involved in the original inequality, children corrected the previous inequality by giving two resources to the child with fewer resources (Experiment 1). However, as the value of the resources increased relative to those initially shared by the experimenter, children were more likely to distribute the two high value resources equally between the two recipients, presumably to minimize the overall inequality in value (Experiments 1 and 2). We found that children specifically use value, not just size, when trying to equalize outcomes (Experiment 3) and further found that children focus on the relative rather than absolute value of the resources they share—when the experimenter had unequally distributed the same high value resource that the child would later share, children corrected the previous inequality by giving two high value resources to the person who had received fewer high value resources. These results illustrate that children attempt to correct past inequalities and try to maintain equality not just in the count of resources but also by using the value of resources. PMID:23882227

On the generation of steady currents in a plasma cylinder using RF waves

International Nuclear Information System (INIS)

Hugrass, W.N.

1980-10-01

The generation of a steady current in a resistive plasma cylinder by means of a travelling wave magnetic field has been studied using the resistive MHD equations. The nonlinear initial-boundary value problem has been solved using a semi-Lagrangian two dimensional algorithm. The numerical code has been used to simulate the Synchromak experiment of Nagoya University. Hollow d.c. current profiles, similar to the experimental data, have been obtained. A simple analytical argument, of a more general nature, shows that classical resistive diffusion cannot lead to a more uniform current distribution

Quasi-experimental study designs series-paper 4: uses and value.

Science.gov (United States)

Bärnighausen, Till; Tugwell, Peter; Røttingen, John-Arne; Shemilt, Ian; Rockers, Peter; Geldsetzer, Pascal; Lavis, John; Grimshaw, Jeremy; Daniels, Karen; Brown, Annette; Bor, Jacob; Tanner, Jeffery; Rashidian, Arash; Barreto, Mauricio; Vollmer, Sebastian; Atun, Rifat

2017-09-01

Quasi-experimental studies are increasingly used to establish causal relationships in epidemiology and health systems research. Quasi-experimental studies offer important opportunities to increase and improve evidence on causal effects: (1) they can generate causal evidence when randomized controlled trials are impossible; (2) they typically generate causal evidence with a high degree of external validity; (3) they avoid the threats to internal validity that arise when participants in nonblinded experiments change their behavior in response to the experimental assignment to either intervention or control arm (such as compensatory rivalry or resentful demoralization); (4) they are often well suited to generate causal evidence on long-term health outcomes of an intervention, as well as nonhealth outcomes such as economic and social consequences; and (5) they can often generate evidence faster and at lower cost than experiments and other intervention studies. Copyright © 2017 Elsevier Inc. All rights reserved.

INFLUENCE OF VACUUM ARC PLASMA EVAPORATOR CATHODE GEOMETRY OF ON VALUE OF ADMISSIBLE ARC DISCHARGE CURRENT

Directory of Open Access Journals (Sweden)

I. A. Ivanou

2015-01-01

Full Text Available An analysis of main design parameters that determine a level of droplet formation intensity at the generating stage of plasma flow has been given in the paper. The paper considers the most widely used designs of water cooled consumable cathodes. Ti or Ti–Si and Fe–Cr alloys have been taken as a material for cathodes. The following calculated data: average ionic charge Zi for titanium plasma +1.6; for «titanium–silicon plasma» +1.2, an electronic discharge 1.6022 ⋅ 10–19 C, an ion velocity vi = 2 ⋅ 104 m/s, an effective volt energy equivalent of heat flow diverted in the cathode Uк = 12 V, temperature of erosion cathode surface Тп = 550 К; temperature of the cooled cathode surface То = 350 К have been accepted in order to determine dependence of a maximum admissible arc discharge current on cathode height. The calculations have been carried out for various values of the cathode heights hк (from 0.02 to 0.05 m. Diameter of a target cathode is equal to 0.08 m for a majority of technological plasma devices, therefore, the area of the erosion surface is S = 0.005 m2.A thickness selection for a consumable target cathode part in the vacuum arc plasma source has been justified in the paper. The thickness ensures formation of minimum drop phase in the plasma flow during arc cathode material evaporation. It has been shown that a maximum admissible current of an arc discharge is practically equal to the minimum current of stable arcing when thickness of the consumable cathode part is equal to 0.05 m. The admissible discharge current can be rather significant and ensure high productivity during coating process with formation of relatively low amount of droplet phase in the coating at small values of hк.

Critical currents in columnar vanadium films

International Nuclear Information System (INIS)

Cherkasova, V.G.; Kolin'ko, A.E.; Slatin, A.E.; Fogel, N.Y.

1982-01-01

The angular dependence of the critical current I/sub c/ is studied in columnar vanadium films. In measurements in constant magnetic fields an anomalous maximum I/sub c/ is found on the I/sub c/(theta) curves at arbitrary values of the external magnetic field and temperature, when the magnetic field is perpendicular to the plane of the specimen. The angular dependence of I/sub c/ measured in constant reduced magnetic fields h = H/H/sub c/2(T,theta) shows no singularities in the vicinity of the angle at which the I/sub c/ peak is found in the case H = const, i.e., the critical current is isotropic. This implies that a change in the relative orientation of the vortices and column boundaries produces no change in critical current. The experimental data obtained permit the conclusion that the anisotropy of I/sub c/ observed in a constant magnetic field H is merely a consequence of the anisotropy of the critical magnetic field H/sub c/: the critical current ''tracking'' the magnitude and angular dependence of H/sub c/

Determination of Soil Moisture Content using Laboratory Experimental and Field Electrical Resistivity Values

Science.gov (United States)

Hazreek, Z. A. M.; Rosli, S.; Fauziah, A.; Wijeyesekera, D. C.; Ashraf, M. I. M.; Faizal, T. B. M.; Kamarudin, A. F.; Rais, Y.; Dan, M. F. Md; Azhar, A. T. S.; Hafiz, Z. M.

2018-04-01

The efficiency of civil engineering structure require comprehensive geotechnical data obtained from site investigation. In the past, conventional site investigation was heavily related to drilling techniques thus suffer from several limitations such as time consuming, expensive and limited data collection. Consequently, this study presents determination of soil moisture content using laboratory experimental and field electrical resistivity values (ERV). Field and laboratory electrical resistivity (ER) test were performed using ABEM SAS4000 and Nilsson400 soil resistance meter. Soil sample used for resistivity test was tested for characterization test specifically on particle size distribution and moisture content test according to BS1377 (1990). Field ER data was processed using RES2DINV software while laboratory ER data was analyzed using SPSS and Excel software. Correlation of ERV and moisture content shows some medium relationship due to its r = 0.506. Moreover, coefficient of determination, R2 analyzed has demonstrate that the statistical correlation obtain was very good due to its R2 value of 0.9382. In order to determine soil moisture content based on statistical correlation (w = 110.68ρ-0.347), correction factor, C was established through laboratory and field ERV given as 19.27. Finally, this study has shown that soil basic geotechnical properties with particular reference to water content was applicably determined using integration of laboratory and field ERV data analysis thus able to compliment conventional approach due to its economic, fast and wider data coverage.

A study of three-dimensional gravity currents on a uniform slope

Science.gov (United States)

Ross, Andrew N.; Linden, P. F.; Dalziel, Stuart B.

2002-02-01

In many geophysical, environmental and industrial situations, a finite volume of fluid with a density different to the ambient is released on a sloping boundary. This leads to the formation of a gravity current travelling up, down and across the slope. We present novel laboratory experiments in which the dense fluid spreads both down-slope (and initially up-slope) and laterally across the slope. The position, shape and dilution of the current are determined through video and conductivity measurements for moderate slopes (5° to 20°). The entrainment coefficient for different slopes is calculated from the experimental results and is found to depend very little on the slope. The value agrees well with previously published values for entrainment into gravity currents on a horizontal surface. The experimental measurements are compared with previous shallow-water models and with a new wedge integral model developed and presented here. It is concluded that these simplified models do not capture all the significant features of the flow. In the models, the current takes the form of a wedge which travels down the slope, but the experiments show the formation of a more complicated current. It is found that the wedge integral model over-predicts the length and width of the gravity current but gives fair agreement with the measured densities in the head. The initial stages of the flow, during which time the wedge shape develops, are studied. It is found that although the influence of the slope is seen relatively quickly for moderate slopes, the time taken for the wedge to develop is much longer. The implications of these findings for safety analysis are briefly discussed.

Comparison of standardized uptake values measured on 18F-NaF PET/CT scans using three different tube current intensities

International Nuclear Information System (INIS)

Valadares, Agnes Araujo; Woellner, Eduardo Bechtloff; Sapienza, Marcelo Tatit; Buchpiguel, Carlos Alberto

2015-01-01

Objective: to analyze standardized uptake values (SUVs) using three different tube current intensities for attenuation correction on 18 FNaF PET/CT scans. Materials and methods: a total of 254 18 F-NaF PET/CT studies were analyzed using 10, 20 and 30 mAs. The SUVs were calculated in volumes of interest (VOIs) drawn on three skeletal regions, namely, right proximal humeral diaphysis (RH), right proximal femoral diaphysis (RF), and first lumbar vertebra (LV1) in a total of 712 VOIs. The analyses covered 675 regions classified as normal (236 RH, 232 RF, and 207 LV1). Results: mean SUV for each skeletal region was 3.8, 5.4 and 14.4 for RH, RF, and LV1, respectively. As the studies were grouped according to mAs value, the mean SUV values were 3.8, 3.9 and 3.7 for 10, 20 and 30 mAs, respectively, in the RH region; 5.4, 5.5 and 5.4 for 10, 20 and 30 mAs, respectively, in the RF region; 13.8, 14.9 and 14.5 for 10, 20 and 30 mAs, respectively, in the LV1 region. Conclusion: the three tube current values yielded similar results for SUV calculation. (author)

Experimental study on magnetically insulated transmission line electrode surface evolution process under MA/cm current density

Energy Technology Data Exchange (ETDEWEB)

Zhang, PengFei; Qiu, Aici [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); State Key Laboratory of Intense Pulse Radiation of Simulation and Effect, Northwest Institute of Nuclear Technology, Xi' an 710024 (China); Hu, Yang; Yang, HaiLiang; Sun, Jiang; Wang, Liangping; Cong, Peitian [State Key Laboratory of Intense Pulse Radiation of Simulation and Effect, Northwest Institute of Nuclear Technology, Xi' an 710024 (China)

2016-03-15

The design of high-current density magnetically insulated transmission line (MITL) is a difficult problem of current large-scale Z-pinch device. In particular, a thorough understanding of the MITL electrode surface evolution process under high current density is lacking. On the “QiangGuang-I” accelerator, the load area possesses a low inductance short-circuit structure with a diameter of 2.85 mm at the cathode, and three reflux columns with a diameter of 3 mm and uniformly distributed circumference at the anode. The length of the high density MITL area is 20 mm. A laser interferometer is used to assess and analyze the state of the MITL cathode and anode gap, and their evolution process under high current density. Experimental results indicate that evident current loss is not observed in the current density area at pulse leading edge, and peak when the surface current density reaches MA/cm. Analysis on electrode surface working conditions indicates that when the current leading edge is at 71.5% of the peak, the total evaporation of MITL cathode structure can be realized by energy deposition caused by ohmic heating. The electrode state changes, and diffusion conditions are reflected in the laser interferometer image. The MITL cathode area mainly exists in metal vapor form. The metal vapor density in the cathode central region is higher than the upper limit of laser penetration density (∼4 × 10{sup 21}/cm{sup 3}), with an expansion velocity of ∼0.96 km/s. The metal vapor density in the electrode outer area may lead to evident distortion of fringes, and its expansion velocity is faster than that in the center area (1.53 km/s).

Experimental Irradiations of Materials and Fuels in the BR2 Reactor: An Overview of Current Programmes

International Nuclear Information System (INIS)

Van Dyck, S.; Koonen, E.; Verwerft, M.; Wéber, M.

2013-01-01

The BR2 material test reactor offers a variety of experimental irradiation possibilities for testing of materials, fuels and instruments. The current paper gives an overview of the recent and ongoing programmes in order to illustrate the experimental potential of the reactor. Three domains of applications are reviewed: Irradiation of materials and fuels for pressurised water reactors (PWR); irradiation of materials for accelerator driven systems (ADS), cooled by liquid lead alloys; and irradiation of fuel for Material Test Reactors (MTR). For PWR relevant tests, a dedicated loop is available, providing a full simulation of the thermo hydraulic conditions of a PWR. ADS related tests require particular control of the irradiation environment and the necessary safety precautions in order to avoid 210 Po contamination. In-core mechanical testing of materials is done in comparison and complimentarily to post-irradiation examinations in order to assess flux related effects on the deformation behaviour of materials. (author)

On Leakage Current Measured at High Cell Voltages in Lithium-Ion Batteries

Energy Technology Data Exchange (ETDEWEB)

Vadivel, Nicole R.; Ha, Seungbum; He, Meinan; Dees, Dennis; Trask, Steve; Polzin, Bryant; Gallagher, Kevin G.

2017-01-01

In this study, parasitic side reactions in lithium-ion batteries were examined experimentally using a potentiostatic hold at high cell voltage. The experimental leakage current measured during the potentiostatic hold was compared to the Tafel expression and showed poor agreement with the expected transfer coefficient values, indicating that a more complicated expression could be needed to accurately capture the physics of this side reaction. Here we show that cross-talk between the electrodes is the primary contribution to the observed leakage current after the relaxation of concentration gradients has ceased. This cross-talk was confirmed with experiments using a lithium-ion conducting glass ceramic (LICGC) separator, which has high conductance only for lithium cations. The cells with LICGC separators showed significantly less leakage current during the potentiostatic hold test compared to cells with standard microporous separators where cross-talk is present. In addition, direct-current pulse power tests show an impedance rise for cells held at high potentials and for cells held at high temperatures, which could be attributed to film formation from the parasitic side reaction. Based on the experimental findings, a phenomenological mechanism is proposed for the parasitic side reaction which accounts for cross-talk and mass transport of the decomposition products across the separator.

Extension of the TCV Operating Space Towards Higher Elongation and Higher Normalized Current

International Nuclear Information System (INIS)

Hofmann, F.; Coda, S.; Lavanchy, P.; Llobet, X.; Marmillod, Ph.; Martin, Y.; Martynov, A.; Mlynar, J.; Moret, J.-M.; Pochelon, A.; Sauter, O.

2002-01-01

Recently, an experimental campaign has been launched on TCV with the aim of exploring and extending the limits of the operating space. The vertical position control system has been optimized, with the help of extensive model calculations, in order to allow operation at the lowest possible stability margin. In addition, the growth rate of the axisymmetric instability has been minimized by choosing optimum values for the plasma triangularity and squareness and by operating close to the current limit imposed by the n= 1 external kink mode. These measures have allowed us to reach record values of elongation, κ=2.8, and normalized current, I N =3.6, in a tokamak with standard aspect ratio, R/a=3.5. (author)

Transverse current at the periphery of the start plasma of the AMBAL-M open device

International Nuclear Information System (INIS)

Taskaev, S.Yu.

1999-01-01

Essential longitudinal electron current was experimentally detected earlier in a start plasma of AMBAL-M open trap and system. This paper studies the current at a plasma periphery and the process resulting in occurrence of transverse current, and determines the value of a transverse current in a transporting range. This study enables to determine that filling of a trap with a thin circular flow and formation of nonequilibrium distribution of a radial electrical field in a plasma by potentials of an electrode front gun are the indium peculiarities of the experiment ensuring essential transverse current [ru

On the generation of steady currents in a plasma cylinder using m=0 radio-frequency waves

International Nuclear Information System (INIS)

Hugrass, W.N.

1981-01-01

The generation of a steady current in a resistive plasma cylinder by means of a travelling-wave magnetic field has been studied by using the resistive MHD equations. The non-linear initial-boundary value problem has been solved numerically. Hollow DC current profiles, similar to the experimental data obtained by other workers, have been found. A simple analytical argument, of a more general nature, shows that classical resistive diffusion cannot lead to a more uniform current distribution. (author)

The Orphee reactor current status and proposed enhancement of experimental capabilities

International Nuclear Information System (INIS)

Breant, P.

1990-01-01

This report provides a description of the Orphee reactor, together with a rapid assessment of its experimental and research capabilities. The plans for enhancing the reactor's experimental capabilities are also presented. (author)

Insulator Contamination Forecasting Based on Fractal Analysis of Leakage Current

Directory of Open Access Journals (Sweden)

Bing Luo

2012-07-01

Full Text Available In this paper, an artificial pollution test is carried out to study the leakage current of porcelain insulators. Fractal theory is adopted to extract the characteristics hidden in leakage current waveforms. Fractal dimensions of the leakage current for the security, forecast and danger zones are analyzed under four types of degrees of contamination. The mean value and the standard deviation of the fractal dimension in the forecast zone are calculated to characterize the differences. The analysis reveals large differences in the fractal dimension of leakage current under different contamination discharge stages and degrees. The experimental and calculation results suggest that the fractal dimension of a leakage current waveform can be used as a new indicator of the discharge process and contamination degree of insulators. The results provide new methods and valid indicators for forecasting contamination flashovers.

The equivalence of numbers: The social value of avoiding health decline: An experimental web-based study

Directory of Open Access Journals (Sweden)

Schwappach David LB

2002-03-01

Full Text Available Abstract Background Health economic analysis aimed at informing policy makers and supporting resource allocation decisions has to evaluate not only improvements in health but also avoided decline. Little is known however, whether the "direction" in which changes in health are experienced is important for the public in prioritizing among patients. This experimental study investigates the social value people place on avoiding (further health decline when directly compared to curative treatments in resource allocation decisions. Methods 127 individuals completed an interactive survey that was published in the World Wide Web. They were confronted with a standard gamble (SG and three person trade-off tasks, either comparing improvements in health (PTO-Up, avoided decline (PTO-Down, or both, contrasting health changes of equal magnitude differing in the direction in which they are experienced (PTO-WAD. Finally, a direct priority ranking of various interventions was obtained. Results Participants strongly prioritized improving patients' health rather than avoiding decline. The mean substitution rate between health improvements and avoided decline (WAD ranged between 0.47 and 0.64 dependent on the intervention. Weighting PTO values according to the direction in which changes in health are experienced improved their accuracy in predicting a direct prioritization ranking. Health state utilities obtained by the standard gamble method seem not to reflect social values in resource allocation contexts. Conclusion Results suggest that the utility of being cured of a given health state might not be a good approximation for the societal value of avoiding this health state, especially in cases of competition between preventive and curative interventions.

Experimental investigation of focusing and transport of heavy-current electron beams

International Nuclear Information System (INIS)

Baranchikov, E.I.; Gordeev, A.V.; Koba, Yu.V.; Korolev, V.D.; Pen'kina, V.S.; Rudakov, L.I.; Smirnov, V.P.; Sukhov, A.D.; Tarumov, E.Z.

The results of an experimental and theoretical study of beam transfer through transverse magnetic fields are outlined. The injection and transport of an annular relativistic electron beam due to a magnetic trap of acute-angle geometry are experimentally studied

Partial discharge measurements on 110kV current transformers. Setting the control value. Case study

Science.gov (United States)

Dan, C.; Morar, R.

2017-05-01

The case study presents a series of partial discharge measurements, reflecting the state of insulation of 110kV CURRENT TRANSFORMERS located in Sibiu county substations. Measurements were performed based on electrical method, using MPD600: an acquisition and analysis toolkit for detecting, recording, and analyzing partial discharges. MPD600 consists of one acquisition unit, an optical interface and a computer with dedicated software. The system allows measurements of partial discharge on site, even in presence of strong electromagnetic interferences because it provides synchronous acquisition from all measurement points. Therefore, measurements, with the ability to be calibrated, do render: - a value subject to interpretation according to IEC 61869-1:2007 + IEC 61869-2:2012 + IEC 61869-3:2011 + IEC 61869-5:2011 and IEC 60270: 2000; - the possibility to determine the quantitative limit of PD (a certain control value) to which the equipment can be operated safely and repaired with minimal costs (relative to the high costs implied by eliminating the consequences of a failure) identified empirically (process in which the instrument transformer subjected to the tests was completely destroyed).

Particle pinch with fully noninductive lower hybrid current drive in Tore Supra.

Science.gov (United States)

Hoang, G T; Bourdelle, C; Pégourié, B; Schunke, B; Artaud, J F; Bucalossi, J; Clairet, F; Fenzi-Bonizec, C; Garbet, X; Gil, C; Guirlet, R; Imbeaux, F; Lasalle, J; Loarer, T; Lowry, C; Travère, J M; Tsitrone, E

2003-04-18

Recently, plasmas exceeding 4 min have been obtained with lower hybrid current drive (LHCD) in Tore Supra. These LHCD plasmas extend for over 80 times the resistive current diffusion time with zero loop voltage. Under such unique conditions the neoclassical particle pinch driven by the toroidal electric field vanishes. Nevertheless, the density profile remains peaked for more than 4 min. For the first time, the existence of an inward particle pinch in steady-state plasma without toroidal electric field, much larger than the value predicted by the collisional neoclassical theory, is experimentally demonstrated.

The use of fair value in measurement of non-current tangible assets by listed companies in Poland

OpenAIRE

Frendzel, Maciej

2011-01-01

This paper presents measurement principles which can applied for non-current tangible assets by listed companies using IFRS and discusses how decision of management of an entity may influence its financial position. Apart from analysis of measurement models applicable for property, plant and equipment and investment property and possible impact of use of fair value on presented assets and financial performance, the article presents results of a research relating to level of usa...

Universal Voltage Conveyor and Current Conveyor in Fast Full-Wave Rectifier

Directory of Open Access Journals (Sweden)

Josef Burian

2012-12-01

Full Text Available This paper deals about the design of a fast voltage-mode full-wave rectifier, where universal voltage conveyor and second-generation current conveyor are used as active elements. Thanks to the active elements, the input and output impedance of the non-linear circuit is infinitely high respectively zero in theory. For the rectification only two diodes and three resistors are required as passive elements. The performance of the circuit is shown on experimental measurement results showing the dynamic range, time response, frequency dependent DC transient value and RMS error for different values of input voltage amplitudes.

Experimental determination of useful resistance value during pasta dough kneading

Science.gov (United States)

Podgornyj, Yu I.; Martynova, T. G.; Skeeba, V. Yu; Kosilov, A. S.; Chernysheva, A. A.; Skeeba, P. Yu

2017-10-01

There is a large quantity of materials produced in the form of dry powder or low humidity granulated masses in the modern market, and there is a need to develop new manufacturing machinery and to renew the existing facilities involved in the production of various loose mixtures. One of the machinery upgrading tasks is enhancing its performance. In view of the fact that experimental research is not feasible in full-scale samples, an experimental installation was to be constructed. The article contains its kinematic scheme and the 3D model. The angle of the kneading blade location, the volume of the loose mixture, rotating frequency and the number of the work member double passes were chosen as variables to carry out the experiment. The technique of the experiment, which includes two stages for the rotary and reciprocating movement of the work member, was proposed. The results of the experimental data processing yield the correlations between the load characteristics of the mixer work member and the angle of the blade, the volume of the mixture and the work member rotating frequency, allowing for the recalculation of loads for this type machines.

Experimental Identification of the Kink Instability as a Poloidal Flux Amplification Mechanism for Coaxial Gun Spheromak Formation

OpenAIRE

Hsu, S. C.; Bellan, P. M.

2003-01-01

The magnetohydrodynamic kink instability is observed and identified experimentally as a poloidal flux amplification mechanism for coaxial gun spheromak formation. Plasmas in this experiment fall into three distinct regimes which depend on the peak gun current to magnetic flux ratio, with (I) low values resulting in a straight plasma column with helical magnetic field, (II) intermediate values leading to kinking of the column axis, and (III) high values leading immediately to a detached plasma...

Experimental and numerical study of influence of ferromagnetic cover on critical current of BiSCCO-2223/Ag tape superconductor

International Nuclear Information System (INIS)

Vojenciak, M; Souc, J; Goemoery, F

2009-01-01

Samples of commercially available BiSCCO-2223/Ag tape have been partially covered by the ferromagnetic material. Improvement of the self-field critical current up to 15 % has been achieved by this procedure. A critical current of such tape strongly depends on geometric and magnetic properties of both, the superconducting tape as well as the ferromagnetic cover. Numerical simulations, based on the critical state model using commercial finite element method (FEM) code, have been performed. Properties of superconductor are characterized by anisotropic dependence of the critical current density on magnetic field as well as detail geometry of filaments. The ferromagnetic material is characterized by nonlinear magnetization curve. Nonlinear dependences of the critical current on selected parameters are shown in this work. Optimization of the cover parameters using these curves has been made. Samples with various parameters have been manufactured for the confirmation of numerical simulations results. Experimental results are in good qualitative agreement with results obtained by numerical simulations.

Value-Based Leadership Approach: A Way for Principals to Revive the Value of Values in Schools

Science.gov (United States)

van Niekerk, Molly; Botha, Johan

2017-01-01

The qualitative research discussed in this article is based on the assumption that school principals as leaders need to establish, develop and maintain a core of shared values in their schools. Our focus is on principals' current perceptions of values in their schools. This is important because values underpin their decisions and actions and thus…

Effects of Current Guides Destruction at Ultra-fast Acceleration of Macrobodies

Science.gov (United States)

Kataev, V. N.; Boriskin, A. S.; Golosov, S. N.; Demidov, V. A.; Klimashov, M. V.; Korolev, P. V.; Makartsev, G. F.; Pikar, A. S.; Russkov, A. S.; Shapovalov, E. V.; Shibitov, Yu. M.

2006-08-01

The paper is devoted to discussion of current guides destruction effects in different accelerators: thermal-electric and electro-magnetic rail accelerator at macrobodies acceleration value of 108-109 m/s2. Experimental results with thermal-electric accelerators powering from megajoule capacitor battery and helical magneto-cumulative generator MCG-100 at currents up to 3.5 MA are analyzed. The process of rails destruction at railgun at pressure magnetic field excess over the limit of metal fluidity is presented. Methods of efficiency coefficient increase of capacitive storage energy transmission to kinetic energy of accelerating body are discussed.

Experimental Method for Characterizing Electrical Steel Sheets in the Normal Direction

Directory of Open Access Journals (Sweden)

Thierry Belgrand

2010-10-01

Full Text Available This paper proposes an experimental method to characterise magnetic laminations in the direction normal to the sheet plane. The principle, which is based on a static excitation to avoid planar eddy currents, is explained and specific test benches are proposed. Measurements of the flux density are made with a sensor moving in and out of an air-gap. A simple analytical model is derived in order to determine the permeability in the normal direction. The experimental results for grain oriented steel sheets are presented and a comparison is provided with values obtained from literature.

Thermal dependence of the current threshold in InGaAsN lasers

International Nuclear Information System (INIS)

Mon, E.; Suarez, N.; Sánchez, M.; Martin, Juan A.

2008-01-01

With active area of InGaAsN lasers are very attractive since they emit in the range of wavelengths of 1.3 to 1.5 pm (CET) bands of conduction of the active zone and cladding in this material [1] layers. In lasers with barriers of GaAs InGaAsN AEc around values are obtained 300 MeV, which guarantees a good confinement of electrons and reported To the order of 126 K values, however, these results have not been satisfactorily explained and there are conflicting reports about this parameter. This work simulates the thermal dependence of the current threshold of InGaAsN lasers including as main mechanisms of loss, leakage current, Auger recombination and recombination Mono [2], which was a good fit of the experimental results reported.

Value Encounters - Modeling and Analyzing Co-creation of Value

Science.gov (United States)

Weigand, Hans

Recent marketing and management literature has introduced the concept of co-creation of value. Current value modeling approaches such as e3-value focus on the exchange of value rather than co-creation. In this paper, an extension to e3-value is proposed in the form of a “value encounter”. Value encounters are defined as interaction spaces where a group of actors meet and derive value by each one bringing in some of its own resources. They can be analyzed from multiple strategic perspectives, including knowledge management, social network management and operational management. Value encounter modeling can be instrumental in the context of service analysis and design.

Comparison of standardized uptake values measured on {sup 18}F-NaF PET/CT scans using three different tube current intensities

Energy Technology Data Exchange (ETDEWEB)

Valadares, Agnes Araujo; Woellner, Eduardo Bechtloff; Sapienza, Marcelo Tatit; Buchpiguel, Carlos Alberto, E-mail: agnesvaladares@me.com [Universidade de Sao Paulo (HC/FMUSP), Sao Paulo, SP (Brazil). Fac. de Medicina. Hospital das Clinicas; Duarte, Paulo Schiavom; Coura-Filho, George Barberio [Instituto do Cancer do Estado de Sao Paulo Octavio Frias de Oliveira (ICESP), Sao Paulo, SP (Brazil)

2015-01-15

Objective: to analyze standardized uptake values (SUVs) using three different tube current intensities for attenuation correction on {sup 18}FNaF PET/CT scans. Materials and methods: a total of 254 {sup 18}F-NaF PET/CT studies were analyzed using 10, 20 and 30 mAs. The SUVs were calculated in volumes of interest (VOIs) drawn on three skeletal regions, namely, right proximal humeral diaphysis (RH), right proximal femoral diaphysis (RF), and first lumbar vertebra (LV1) in a total of 712 VOIs. The analyses covered 675 regions classified as normal (236 RH, 232 RF, and 207 LV1). Results: mean SUV for each skeletal region was 3.8, 5.4 and 14.4 for RH, RF, and LV1, respectively. As the studies were grouped according to mAs value, the mean SUV values were 3.8, 3.9 and 3.7 for 10, 20 and 30 mAs, respectively, in the RH region; 5.4, 5.5 and 5.4 for 10, 20 and 30 mAs, respectively, in the RF region; 13.8, 14.9 and 14.5 for 10, 20 and 30 mAs, respectively, in the LV1 region. Conclusion: the three tube current values yielded similar results for SUV calculation. (author)

Observation and analysis of halo current in EAST

Science.gov (United States)

Chen, Da-Long; Shen, Biao; Qian, Jin-Ping; Sun, You-Wen; Liu, Guang-Jun; Shi, Tong-Hui; Zhuang, Hui-Dong; Xiao, Bing-Jia

2014-06-01

Plasma in a typically elongated cross-section tokamak (for example, EAST) is inherently unstable against vertical displacement. When plasma loses the vertical position control, it moves downward or upward, leading to disruption, and a large halo current is generated helically in EAST typically in the scrape-off layer. When flowing into the vacuum vessel through in-vessel components, the halo current will give rise to a large J × B force acting on the vessel and the in-vessel components. In EAST VDE experiment, part of the eddy current is measured in halo sensors, due to the large loop voltage. Primary experimental data demonstrate that the halo current first lands on the outer plate and then flows clockwise, and the analysis of the information indicates that the maximum halo current estimated in EAST is about 0.4 times the plasma current and the maximum value of TPF × Ih/IP0 is 0.65, furthermore Ih/Ip0 and TPF × Ih/Ip0 tend to increase with the increase of Ip0. The test of the strong gas injection system shows good success in increasing the radiated power, which may be effective in reducing the halo current.

Experimental test of the PCAC-hypothesis in charged current neutrino and antineutrino interactions on protons

Science.gov (United States)

Jones, G. T.; Jones, R. W. L.; Kennedy, B. W.; O'Neale, S. W.; Klein, H.; Morrison, D. R. O.; Schmid, P.; Wachsmuth, H.; Miller, D. B.; Mobayyen, M. M.; Wainstein, S.; Aderholz, M.; Hoffmann, E.; Katz, U. F.; Kern, J.; Schmitz, N.; Wittek, W.; Allport, P.; Myatt, G.; Radojicic, D.; Bullock, F. W.; Burke, S.

1987-03-01

Data obtained with the bubble chamber BEBC at CERN are used for the first significant test of Adler's prediction for the neutrino and antineutrino-proton scattering cross sections at vanishing four-momentum transfer squared Q 2. An Extended Vector Meson Dominance Model (EVDM) is applied to extrapolate Adler's prediction to experimentally accessible values of Q 2. The data show good agreement with Adler's prediction for Q 2→0 thus confirming the PCAC hypothesis in the kinematical region of high leptonic energy transfer ν>2 GeV. The good agreement of the data with the theoretical predictions also at higher Q 2, where the EVDM terms are dominant, also supports this model. However, an EVDM calculation without PCAC is clearly ruled out by the data.

Experimental test of the PCAC-hypothesis in charged current neutrino and antineutrino interactions on protons

International Nuclear Information System (INIS)

Jones, G.T.; Jones, R.W.L.; Kennedy, B.W.; O'Neale, S.W.; Klein, H.; Morrison, D.R.O.; Schmid, P.; Wachsmuth, H.; Allport, P.; Myatt, G.; Radojicic, D.; Bullock, F.W.; Burke, S.

1987-01-01

Data obtained with the bubble chamber BEBC at CERN are used for the first significant test of Adler's prediction for the neutrino and antineutrino-proton scattering cross sections at vanishing four-momentum transfer squared Q 2 . An Extended Vector Meson Dominance Model (EVDM) is applied to extrapolate Adler's prediction to experimentally accessible values of Q 2 . The data show good agreement with Adler's prediction for Q 2 → 0 thus confirming the PCAC hypothesis in the kinematical region of high leptonic energy transfer ν > 2 GeV. The good agreement of the data with the theoretical predictions also at higher Q 2 , where the EVDM terms are dominant, also supports this model. However, an EVDM calculation without PCAC is clearly ruled out by the data. (orig.)

Adjustable direct current and pulsed circuit fault current limiter

Science.gov (United States)

Boenig, Heinrich J.; Schillig, Josef B.

2003-09-23

A fault current limiting system for direct current circuits and for pulsed power circuit. In the circuits, a current source biases a diode that is in series with the circuits' transmission line. If fault current in a circuit exceeds current from the current source biasing the diode open, the diode will cease conducting and route the fault current through the current source and an inductor. This limits the rate of rise and the peak value of the fault current.

Experimental and numerical examination of eddy (Foucault) currents in rotating micro-coils: Generation of heat and its impact on sample temperature

Science.gov (United States)

Aguiar, Pedro M.; Jacquinot, Jacques-François; Sakellariou, Dimitris

2009-09-01

The application of nuclear magnetic resonance (NMR) to systems of limited quantity has stimulated the use of micro-coils (diameter Foucault (eddy) currents, which generate heat. We report the first data acquired with a 4 mm MACS system and spinning up to 10 kHz. The need to spin faster necessitates improved methods to control heating. We propose an approximate solution to calculate the power losses (heat) from the eddy currents for a solenoidal coil, in order to provide insight into the functional dependencies of Foucault currents. Experimental tests of the dependencies reveal conditions which result in reduced sample heating and negligible temperature distributions over the sample volume.

Experimental and numerical examination of eddy (Foucault) currents in rotating micro-coils: Generation of heat and its impact on sample temperature.

Science.gov (United States)

Aguiar, Pedro M; Jacquinot, Jacques-François; Sakellariou, Dimitris

2009-09-01

The application of nuclear magnetic resonance (NMR) to systems of limited quantity has stimulated the use of micro-coils (diameter Foucault (eddy) currents, which generate heat. We report the first data acquired with a 4mm MACS system and spinning up to 10kHz. The need to spin faster necessitates improved methods to control heating. We propose an approximate solution to calculate the power losses (heat) from the eddy currents for a solenoidal coil, in order to provide insight into the functional dependencies of Foucault currents. Experimental tests of the dependencies reveal conditions which result in reduced sample heating and negligible temperature distributions over the sample volume.

Analysis of Steady-State Error in Torque Current Component Control of PMSM Drive

Directory of Open Access Journals (Sweden)

BRANDSTETTER, P.

2017-05-01

Full Text Available The paper presents dynamic properties of a vector controlled permanent magnet synchronous motor drive supplied by a voltage source inverter. The paper deals with a control loop for the torque producing stator current. There is shown fundamental mathematical description for the vector control structure of the permanent magnet synchronous motor drive with respect to the current control for d-axis and q-axis of the rotor rotating coordinate system. The derivations of steady-state deviation for schemes with and without decoupling circuits are described for q-axis. The properties of both schemes are verified by MATLAB-SIMULINK program considering a lower and a higher value of inertia and by experimental measurements in our laboratory. The simulation and experimental results are presented and discussed at the end of the paper.

Experimental study of the positive leader velocity as a function of the current in the initial and final-jump phases of a spark discharge

International Nuclear Information System (INIS)

Andreev, A. G.; Bazelyan, E. M.; Bulatov, M. U.; Kuzhekin, I. P.; Makalsky, L. M.; Sukharevskij, D. I.; Syssoev, V. S.

2008-01-01

A positive leader in air at gap lengths of up to 8 m was studied experimentally on an open experimental stand. The voltage source was a 6-MV pulsed voltage generator or an artificial charged aerosol cloud. The dependence of the leader velocity on the current in the range 0.2-8 A was determined by simultaneously recording the optical picture and electric parameters of the discharge. Particular attention was paid to the final-jump phase of the discharge, when the gap was completely bridged by the streamer zone of the leader. It is shown that the character of the dependence of the leader velocity on the current in this phase remains unchanged; hence, the final-jump phase can be used in experiments in which the current has to be varied within a wide range. For this purpose, one can use a damping resistance, which is inefficient in the initial phase. The parameters of the power-law dependence of the leader velocity on the current at currents of a few amperes are established reliably. It is found that the power-law dependence with constant parameters is inapplicable to calculate the leader velocity at currents of about 0.1 A, which correspond to the lower limit of the leader viability.

Implementation of thermoelectric module for cooling process of microscale experimental room

Science.gov (United States)

Gołebiowska, Justyna; Żelazna, Agnieszka; Zioło, Paweł

2017-08-01

Thermoelectric modules, also known as Peltier modules, are used for cooling small devices and also, according to literature, in refrigeration. They can be an alternative to conventional refrigeration systems based on the use of compressors chillers powered by AC power. Peltier modules are powered by direct current (DC), which allows to power them directly supply by photovoltaic modules. In this paper operation of thermoelectric module used for cooling experimental room of cubature 0.125 m3 is presented. The study involves investigation of temperatures achieved on the cold and hot sides of module and inside the experimental room depending on the values of module supplying current. These studies provide an introduction to the assessment of the influence of different methods of heat removal on the hot side of thermoelectric module on cooling efficiency of whole system.

A TECHNIQUE OF EXPERIMENTAL INVESTIGATIONS OF LINEAR IMPULSE ELECTROMECHANICAL CONVERTERS

Directory of Open Access Journals (Sweden)

V.F. Bolyukh

2017-04-01

figures obtained by means of a mathematical model that describes the ultrafast electromagnetic, thermal and mechanical processes that occur when the yoke moves relative to the inductor. Originality. For the first time offered during experimental studies of impulse linear electromechanical converter to both to measure the electrical parameters, namely the inductor winding current, and mechanical parameters characterizing the power and velocity performance with yoke actuator. Practical value. The technique of experimental investigations the parameters of the linear pulse electromechanical converter that can be used to investigate the shock-power devices and electromechanical accelerators is proposed.

Simple model to explain the temperature dependence of the lower hybrid current drive efficiency

International Nuclear Information System (INIS)

Ushigusa, K.

1996-01-01

Dissipated power in the spectral gap is taken into account in deriving analytically the lower hybrid current drive efficiency. The efficiency is determined by a minimum down-shifted phase velocity υ L and the quasi-linear velocity diffusion coefficient at the spectral gap D' W in addition to the original wave spectrum. To explain present experimental results in both JT-60 and ASDEX, υ L must be close to the Landau damping limit (υ L ∼ 2.7υ te ) and D' W must be the same order of magnitude as the collisional friction at υ L . With the suggested values of these two parameters from experimental results, the driven current is mainly determined by the launched wave spectrum, while most of the wave power is dissipated at the spectral gap. This characteristic can explain both the temperature and the N || dependence of the current drive efficiency. (author)

Experimental observations of the tearing of an electron current sheet

International Nuclear Information System (INIS)

Gekelman, W.; Pfister, H.

1988-01-01

A neutral magnetic sheet, in which the current is carried mainly by the electrons, is set up in a laboratory plasma. By forcing the current through a thin slot, the ratio of the length to height t of the sheet may be varied; the current is observed to tear when tapprox. >30. The structure of the magnetic islands and their associated currents is fully three dimensional, although a linear two-dimensional theory gives a very good estimate of the tearing mode growth time. Tearing is accompanied by the generation of significant Hall currents, and magnetic disturbances are observed to propagate at the whistler wave speed

Axial mercury segregation in direct current operated low-pressure argon-mercury gas discharges: Part I. Experimental

International Nuclear Information System (INIS)

Gielen, John W A M; Groot, Simon de; Mullen, Joost J A M van der

2004-01-01

Due to cataphoresis, axial segregation of mercury will occur when the gas discharge of a fluorescent lamp is operated by means of a direct current. A consequence of this is a non-uniform axial luminance distribution along the lamp. To determine the degree of axial mercury segregation experimentally, axial luminance distributions have been measured which are converted into axial mercury vapour pressure distributions by an appropriate calibration method. The mercury segregation has been investigated for variations in lamp tube radius (3.6-4.8 mm), argon buffer gas pressure (200-600 Pa) and lamp current (100-250 mA) at mercury vapour pressures set at the anode in the range from 0.2 to 9.0 Pa. From the experiments it has been concluded that the mercury vapour pressure gradient at any axial position for a certain lamp tube diameter, argon pressure and lamp current depends on the local mercury vapour pressure. This observation is in contrast to assumptions made in earlier modelling publications in which one mercury vapour pressure gradient is used for all axial positions. By applying a full factorial design, an empirical relation of the mercury segregation is found for any set of parameters inside the investigated parameter ranges

Value activity monitoring

NARCIS (Netherlands)

de Alencar Silva, P.

2013-01-01

Current value modeling ontologies are grounded on the economic premise that profit sharing is a critical condition to be assessed during the configuration of a value constellation. Such a condition ought to be reinforced through a monitoring mechanism design, since a value model expresses only

A finite difference method for numerical solution of the Nernst-Planck equations when convective flux and electric current are involved

International Nuclear Information System (INIS)

Aguilera, V.M.; Garrido, J.; Mafe, S.; Pellicer, J.

1985-01-01

An algorithm for the solution of Nernst-Planck equations with simultaneous convective flux and electric current has been developed without using Poisson's equation. The numerical simulation which has been developed reproduces the behaviour of the system employing their experimental variables as parameters of the algorithm. However, other procedures are only capable of dealing with some of the experimental conditions described here. The agreement between the theoretically predicted values and the experimentally obtained is quite reasonable. (author)

Quantum decay of metastable current states in rf squids

International Nuclear Information System (INIS)

Dmitrenko, I.M.; Khlus, V.A.; Tsoj, C.M.; Shnyrkov, V.I.

1985-01-01

Quantum decay of metastable current states in a rf SQUID superconducting ring of a hysteresis mode are considered. Point contacts are used as a Josephson weak link. The first derivative of rf IVC, dVsub(T)/dIsub(RF), is measured which gives the dependence of the density of decay probability on the amplitude of magnetic flux oscillations in the ring. The temperature dependence of probability distribution width between 4.2 and 0.5 K suggests that for most of high-ohmic contacts Nb-Nb, Nb-Ag-Nb the quantum mechanisms of decay become dominant beginning with the temperature of about 2 K. The experimental parameters of distribution of decay probability in the quantum limit are compared to those calculated by the theory of macroscopic quantum tunneling in the limit of high and low dissipation. The experimental values of probability density distribution width and characteristic quantum temperature are higher than the theoretical ones, the fact can be attributed to the deviation of current-phase relation of contact from a sinusoidal one. Besides, some contacts seem to correspond to the case of an intermediate value of dissipation. As the frequency of rf oscillations varies from 30 to 6 MHz, the distribution width remains unchanged in accordance with the theory of quantum tunneling decay of metastable current state in the ring in the limit of high damping. At low temperatures (T approximately 0.5 K), and rather small damping coefficient, the density of probability displays anomalous peaks when the amplitude of rf oscillations is lower considerably than the critical vaiue of magnetic flux in the ring

Experimental study of blockage of monochromatic waves by counter currents

NARCIS (Netherlands)

Suastika, I.K.

1999-01-01

Blockage of waves by a current can occur if waves are propagating on a spatially varying opposing current in which the velocity is increasing in the wave propagation direction. The ongoing waves become shorter and steeper while they are propagating against the current. Blocking occurs at the

Growth and characterization of high current density, high-speed InAs/AlSb resonant tunneling diodes

Science.gov (United States)

Soderstrom, J. R.; Brown, E. R.; Parker, C. D.; Mahoney, L. J.; Yao, J. Y.

1991-01-01

InAs/AlSb double-barrier resonant tunneling diodes with peak current densities up to 370,000 A/sq cm and high peak-to-valley current ratios of 3.2 at room temperature have been fabricated. The peak current density is well-explained by a stationary-state transport model with the two-band envelope function approximation. The valley current density predicted by this model is less than the experimental value by a factor that is typical of the discrepancy found in other double-barrier structures. It is concluded that threading dislocations are largely inactive in the resonant tunneling process.

Variability of photovoltaic panels efficiency depending on the value of the angle of their inclination relative to the horizon

Directory of Open Access Journals (Sweden)

Majdak Marek

2017-01-01

Full Text Available The objective of this paper was to determine the relationship between the efficiency of photovoltaic panels and the value of the angle of their inclination relative to the horizon. For the purpose of experimental research have been done tests on the photovoltaic modules made of monocrystalline, polycrystalline and amorphous silicon. The experiment consisted of measurement of the voltage and current generated by photovoltaic panels at a known value of solar radiation and a specified resistance value determined by using resistor with variable value of resistance and known value of the angle of their inclination relative to the horizon.

Current status of baryon spectroscopy

International Nuclear Information System (INIS)

Wali, K.C.

1975-01-01

The basic ideas of some of the current models and the experimental numerical comparisons are discussed briefly. Included are realistic or constituent quark models, experimental comparison, the experimental and theoretical basis for the assignments, algebraic quark models, and confinement schemes

Hysteresis of critical currents of superconducting bridges in low perpendicular magnetic fields

International Nuclear Information System (INIS)

Aomine, T.; Tanaka, E.; Yamasaki, S.; Tani, K.; Yonekura, A.

1989-01-01

Hysteresis of critical currents I c of superconducting bridges with In, Nb, and NbN has been studied in low perpendicular magnetic fields. Influences of bridge geometry, small field sweep, trapped flux, and bombardment of argon ions on the hysteresis were made clear. The experimental results suggest that the edge pinning and trapped flux in the bank of bridges are associated with the hysteresis. The peak value of I c of NbN bridges, as well as granular Al and In bridges reported before, in decreasing fields agrees with the calculated pair-breaking current. The origin of the hysteresis is discussed

High-temperature performance of MoS{sub 2} thin-film transistors: Direct current and pulse current-voltage characteristics

Energy Technology Data Exchange (ETDEWEB)

Jiang, C.; Samnakay, R.; Balandin, A. A., E-mail: balandin@ee.ucr.edu [Nano-Device Laboratory (NDL), Department of Electrical Engineering, Bourns College of Engineering, University of California—Riverside, Riverside, California 92521 (United States); Phonon Optimized Engineered Materials (POEM) Center, Materials Science and Engineering Program, University of California—Riverside, Riverside, California 92521 (United States); Rumyantsev, S. L. [Department of Electrical, Computer, and Systems Engineering, Center for Integrated Electronics, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States); Ioffe Physical-Technical Institute, St. Petersburg 194021 (Russian Federation); Shur, M. S. [Department of Electrical, Computer, and Systems Engineering, Center for Integrated Electronics, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States)

2015-02-14

We report on fabrication of MoS{sub 2} thin-film transistors (TFTs) and experimental investigations of their high-temperature current-voltage characteristics. The measurements show that MoS{sub 2} devices remain functional to temperatures of at least as high as 500 K. The temperature increase results in decreased threshold voltage and mobility. The comparison of the direct current (DC) and pulse measurements shows that the direct current sub-linear and super-linear output characteristics of MoS{sub 2} thin-films devices result from the Joule heating and the interplay of the threshold voltage and mobility temperature dependences. At temperatures above 450 K, a kink in the drain current occurs at zero gate voltage irrespective of the threshold voltage value. This intriguing phenomenon, referred to as a “memory step,” was attributed to the slow relaxation processes in thin films similar to those in graphene and electron glasses. The fabricated MoS{sub 2} thin-film transistors demonstrated stable operation after two months of aging. The obtained results suggest new applications for MoS{sub 2} thin-film transistors in extreme-temperature electronics and sensors.

Low Voltage Current Mode Switched-Current-Mirror Mixer

Directory of Open Access Journals (Sweden)

Chunhua Wang

2009-09-01

Full Text Available A new CMOS active mixer topology can operate at 1 V supply voltage by use of SCM (switched currentmirror. Such current-mode mixer requires less voltage headroom with good linearization. Mixing is achieved with four improved current mirrors, which are alternatively activated. For ideal switching, the operation is equivalent to a conventional active mixer. This paper analyzes the performance of the SCM mixer, in comparison with the conventional mixer, demonstrating competitive performance at a lower supply voltage. Moreover, the new mixer’s die, without any passive components, is very small, and the conversion gain is easy to adjust. An experimental prototype was designed and simulated in standard chartered 0.18μm RF CMOS Process with Spectre in Cadence Design Systems. Experimental results show satisfactory mixer performance at 2.4 GHz.

Market Review: Market values summary; March market review; Current market data

International Nuclear Information System (INIS)

Anon.

1996-01-01

This article is the March 1996 uranium market summary. In this reporting period, there were two deals in the natural uranium spot market and four deals in the long-term market. The unrestricted value moved upward to $13.50 per pound U3O8, and the long-term price indicator was $16.50. In the UF6 market, there was but a single deal. Both the restricted and the unrestricted values moved upward, to $47.00 and $41.25 respectively. The restricted and the unrestricted transaction values moved upward, to $13.35 and $8.40 respectively. In the enrichment services market, there were no transactions. Both the restricted and the unrestricted SWU values remained constant at $97 and $90 respectively. Active uranium supply rose, while active demand decreased sharply

Experimental investigation into the seismic behavior of nuclear power plant shear wall structures

International Nuclear Information System (INIS)

Kenneally, R.M.; Burns, J.J. Jr.

1988-01-01

Nuclear power plant structures are designed to resist large earthquakes. However, as new data are obtained on earthquake activity throughout the United States, plant design earthquake levels have increased. The U.S. Nuclear Regulatory Commission is sponsoring an analytical-experimental research program to obtain information on the strucutral response of nuclear power plant shear wall strucutres subjected to earthquake motions within and beyond their design basis. Using different size scale models constructed with microconcrete and prototypical concrete this research has demonstrated consistent results for measured values of stiffness at load levels within the design basis. Furthermore, the values are well below the theoretical stiffnesses calculated from an uncracked cross-section strength-of-materials approach. Current program emphasis is to assess the credibility of previous experimental work by beginning to resolve the 'stiffness difference' issue. (orig.)

Can values drive value for sustainable business? : An analyzing and interpreting case study of Konsum Värmland Value-creation

OpenAIRE

Zetterberg, Madeleine

2007-01-01

Abstract Historically, value was believed to be created and embedded in the manufacturing process, implying that companies were the creators of value. Conversely, the notion of value-creation changed during the last decades and has implemented the customer orientation and service centred view. Instead, researchers currently believe that companies only can offer value-propositions, which means that value is to be created by the customers. Services and goods are much about values and identity t...

Variation of local critical current and its influence on overall current of bent multifilamentary Bi2223/Ag tape

International Nuclear Information System (INIS)

Ochiai, S.; Doko, D.; Rokkaku, H.; Fujimoto, M.; Okuda, H.; Hojo, M.; Tanaka, M.; Sugano, M.; Osamura, K.; Mimura, M.

2006-01-01

The correlation between the local and overall currents in a multifilamentary Bi2223/Ag/Ag alloy composite tape under bending strain was studied. The correlation of the measured distributed local critical current and n-value to overall critical current was described comprehensively with a voltage summation model that regards the overall sample to be composed of a series circuit. The analysis of the measured critical current and n-value revealed that the distribution of local critical current could be described with the Weibull distribution function and the n-value could be expressed as a function of critical current as a first approximation. By combining the Weibull distribution function of the local critical current, the empirical formula of the n-value as a function of critical current, voltage summation model and Monte Carlo method, the overall current and n-value could be predicted fairly well from those of local elements

Influence of the optical fiber type on the performances of fiber-optics current sensor dedicated to plasma current measurement in ITER.

Science.gov (United States)

Aerssens, Matthieu; Descamps, Frédéric; Gusarov, Andrei; Mégret, Patrice; Moreau, Philippe; Wuilpart, Marc

2015-07-01

In this paper, we compare, by means of simulations using the Jones formalism, the performances of several optical fiber types (low birefringence and spun fibers) for the measurement of plasma current in international thermonuclear experimental reactor (ITER). The main results presented in this paper concern the minimum value of the ratio between the beat length and the spun period, which allows meeting the ITER current measurement specifications. Assuming a high-birefringence spun fiber with a beat length of 3 mm, we demonstrate that the minimum ratio between the beat length and the spun period is 4.4 when considering a 28 m long sensing fiber surrounding the vacuum vessel. This minimum ratio rises to 10.14 when a 100 m long lead fiber connecting the interrogating system to the sensing fiber is taken into account.

Computer modelling of eddy current probes

International Nuclear Information System (INIS)

Sullivan, S.P.

1992-01-01

Computer programs have been developed for modelling impedance and transmit-receive eddy current probes in two-dimensional axis-symmetric configurations. These programs, which are based on analytic equations, simulate bobbin probes in infinitely long tubes and surface probes on plates. They calculate probe signal due to uniform variations in conductor thickness, resistivity and permeability. These signals depend on probe design and frequency. A finite element numerical program has been procured to calculate magnetic permeability in non-linear ferromagnetic materials. Permeability values from these calculations can be incorporated into the above analytic programs to predict signals from eddy current probes with permanent magnets in ferromagnetic tubes. These programs were used to test various probe designs for new testing applications. Measurements of magnetic permeability in magnetically biased ferromagnetic materials have been performed by superimposing experimental signals, from special laboratory ET probes, on impedance plane diagrams calculated using these programs. (author). 3 refs., 2 figs

A Monte Carlo simulation on critical current distribution of bent-damaged multifilamentary Bi2223 composite tape

International Nuclear Information System (INIS)

Ochiai, S.; Okuda, H.; Fujimoto, M.; Shin, J.K.; Oh, S.S.; Ha, D.W.

2011-01-01

We simulate critical current distribution of bent-damaged Bi2223 composite tape. We use a Monte Carlo method and a damage evolution model for simulation. With the present simulation approach, experimental results are described well. Critical current distribution stems mainly from difference in damage evolution. It was attempted to reproduce the measured critical current (I c ) distributions of the Bi2223 composite tape bent by 0-0.833% by simulation. Simulation was carried out with a Monte Carlo method in combination with a model that correlates the critical current to damage evolution. Two variables that differ from specimen to specimen were input in the simulation. One was the damage strain parameter, with which the difference in extent of damage among specimens was expressed. Another was the original critical current (I c0 ) values at zero bending strain. With the present simulation approach, the measured distributions of critical current at various bending strains, and the measured variations of average and coefficient of variation of critical current values with increasing bending strain were reproduced well.

Why should correction values be better known than the measurand true value?

International Nuclear Information System (INIS)

Pavese, Franco

2013-01-01

Since the beginning of the history of modern measurement science, the experimenters faced the problem of dealing with systematic effects, as distinct from, and opposed to, random effects. Two main schools of thinking stemmed from the empirical and theoretical exploration of the problem, one dictating that the two species should be kept and reported separately, the other indicating ways to combine the two species into a single numerical value for the total uncertainty (often indicated as 'error'). The second way of thinking was adopted by the GUM, and, generally, adopts the method of assuming that their expected value is null by requiring, for all systematic effects taken into account in the model, that corresponding 'corrections' are applied to the measured values before the uncertainty analysis is performed. On the other hand, about the value of the measurand intended to be the object of measurement, classical statistics calls it 'true value', admitting that a value should exist objectively (e.g. the value of a fundamental constant), and that any experimental operation aims at obtaining an ideally exact measure of it. However, due to the uncertainty affecting every measurement process, this goal can be attained only approximately, in the sense that nobody can ever know exactly how much any measured value differs from the true value. The paper discusses the credibility of the numerical value attributed to an estimated correction, compared with the credibility of the estimate of the location of the true value, concluding that the true value of a correction should be considered as imprecisely evaluable as the true value of any 'input quantity', and of the measurand itself. From this conclusion, one should derive that the distinction between 'input quantities' and 'corrections' is not justified and not useful

Market review: Market values summary July market review/current market data

International Nuclear Information System (INIS)

Anon.

1996-01-01

A summary of financial data for the uranium spot market is provided. Recent transactions are tabulated, including uranium sales, natural uranium loans, conversion sales, and enrichment sales. A market values summary and long-term price indicators are also provided. The July 1996 market review data includes summaries of near-term uranium sales, near-term supply/demand, NUEXCO values, USEC prices, and calculated worth of enriched uranium. Active projects in uranium, conversion, and separative work supply and demand are listed. International market values are tabulated for 22 selected currencies

Numerical modeling and experimental validation of thermoplastic composites induction welding

Science.gov (United States)

Palmieri, Barbara; Nele, Luigi; Galise, Francesco

2018-05-01

In this work, a numerical simulation and experimental test of the induction welding of continuous fibre-reinforced thermoplastic composites (CFRTPCs) was provided. The thermoplastic Polyamide 66 (PA66) with carbon fiber fabric was used. Using a dedicated software (JMag Designer), the influence of the fundamental process parameters such as temperature, current and holding time was investigated. In order to validate the results of the simulations, and therefore the numerical model used, experimental tests were carried out, and the temperature values measured during the tests were compared with the aid of an optical pyrometer, with those provided by the numerical simulation. The mechanical properties of the welded joints were evaluated by single lap shear tests.

Experimental Results of a DC Bus Voltage Level Control for a Load-Controlled Marine Current Energy Converter

Directory of Open Access Journals (Sweden)

Johan Forslund

2015-05-01

Full Text Available This paper investigates three load control methods for a  marine current energy converter using a vertical axis current  turbine (VACT mounted on a permanent magnet synchronous generator  (PMSG. The three cases are; a fixed AC load, a fixed pulse width  modulated (PWM DC load and DC bus voltage control of a DC  load. Experimental results show that the DC bus voltage control  reduces the variations of rotational speed by a factor of 3.5 at the cost  of slightly increased losses in the generator and transmission lines.  For all three cases, the tip speed ratio \\(\\lambda\\ can be kept close to  the expected \\(\\lambda_{opt}\\. The power coefficient is estimated to be  0.36 at \\(\\lambda_{opt}\\; however, for all three cases, the average  extracted power was about \\(\\sim 19\\\\%. A maximum power point  tracking (MPPT system, with or without water velocity measurement,  could increase the average extracted power.

Automatic J–A Model Parameter Tuning Algorithm for High Accuracy Inrush Current Simulation

Directory of Open Access Journals (Sweden)

Xishan Wen

2017-04-01

Full Text Available Inrush current simulation plays an important role in many tasks of the power system, such as power transformer protection. However, the accuracy of the inrush current simulation can hardly be ensured. In this paper, a Jiles–Atherton (J–A theory based model is proposed to simulate the inrush current of power transformers. The characteristics of the inrush current curve are analyzed and results show that the entire inrush current curve can be well featured by the crest value of the first two cycles. With comprehensive consideration of both of the features of the inrush current curve and the J–A parameters, an automatic J–A parameter estimation algorithm is proposed. The proposed algorithm can obtain more reasonable J–A parameters, which improve the accuracy of simulation. Experimental results have verified the efficiency of the proposed algorithm.

Proportional-Integral-Resonant AC Current Controller

Directory of Open Access Journals (Sweden)

STOJIC, D.

2017-02-01

Full Text Available In this paper an improved stationary-frame AC current controller based on the proportional-integral-resonant control action (PIR is proposed. Namely, the novel two-parameter PIR controller is applied in the stationary-frame AC current control, accompanied by the corresponding parameter-tuning procedure. In this way, the proportional-resonant (PR controller, common in the stationary-frame AC current control, is extended by the integral (I action in order to enable the AC current DC component tracking, and, also, to enable the DC disturbance compensation, caused by the voltage source inverter (VSI nonidealities and by nonlinear loads. The proposed controller parameter-tuning procedure is based on the three-phase back-EMF-type load, which corresponds to a wide range of AC power converter applications, such as AC motor drives, uninterruptible power supplies, and active filters. While the PIR controllers commonly have three parameters, the novel controller has two. Also, the provided parameter-tuning procedure needs only one parameter to be tuned in relation to the load and power converter model parameters, since the second controller parameter is directly derived from the required controller bandwidth value. The dynamic performance of the proposed controller is verified by means of simulation and experimental runs.

No prognostic value added by vitamin D pathway SNPs to current prognostic system for melanoma survival.

Directory of Open Access Journals (Sweden)

Li Luo

Full Text Available The prognostic improvement attributed to genetic markers over current prognostic system has not been well studied for melanoma. The goal of this study is to evaluate the added prognostic value of Vitamin D Pathway (VitD SNPs to currently known clinical and demographic factors such as age, sex, Breslow thickness, mitosis and ulceration (CDF. We utilized two large independent well-characterized melanoma studies: the Genes, Environment, and Melanoma (GEM and MD Anderson studies, and performed variable selection of VitD pathway SNPs and CDF using Random Survival Forest (RSF method in addition to Cox proportional hazards models. The Harrell's C-index was used to compare the performance of model predictability. The population-based GEM study enrolled 3,578 incident cases of cutaneous melanoma (CM, and the hospital-based MD Anderson study consisted of 1,804 CM patients. Including both VitD SNPs and CDF yielded C-index of 0.85, which provided slight but not significant improvement by CDF alone (C-index = 0.83 in the GEM study. Similar results were observed in the independent MD Anderson study (C-index = 0.84 and 0.83, respectively. The Cox model identified no significant associations after adjusting for multiplicity. Our results do not support clinically significant prognostic improvements attributable to VitD pathway SNPs over current prognostic system for melanoma survival.

Multi-Valued Planar Hall Resistance Manipulated by Current Induced Magnetic Field in Fe Films Grown on GaAs(001) Substrates

Science.gov (United States)

Khym, Sungwon; Yoo, Taehee; Lee, Hakjoon; Lee, Sangyeop; Lee, Sanghoon; Liu, Xinyu; Furdyna, Jacek K.; Lee, Dong Uk; Kim, Eun Kyu

2012-09-01

A Hall device was fabricated from single-crystal Fe film having two in-plane magnetic easy axes. Planar Hall resistance measured by sequential application of current pulses to the metal strip that was deposited on the top of a Hall bar showed a hysteresis similar to that observed by scanning an external magnetic field. It was shown that discrete Hall resistance values in the hysteresis, which correspond to specific multidomain structures in Fe film, can be created by the application of appropriate sequences of current pulses to the metal strip, and can thus be used for read/write logic applications.

Experimental assessment of blade tip immersion depth from free surface on average power and thrust coefficients of marine current turbine

Science.gov (United States)

Lust, Ethan; Flack, Karen; Luznik, Luksa

2014-11-01

Results from an experimental study on the effects of marine current turbine immersion depth from the free surface are presented. Measurements are performed with a 1/25 scale (diameter D = 0.8m) two bladed horizontal axis turbine towed in the large towing tank at the U.S. Naval Academy. Thrust and torque are measured using a dynamometer, mounted in line with the turbine shaft. Shaft rotation speed and blade position are measured using a shaft position indexing system. The tip speed ratio (TSR) is adjusted using a hysteresis brake which is attached to the output shaft. Two optical wave height sensors are used to measure the free surface elevation. The turbine is towed at 1.68 m/s, resulting in a 70% chord based Rec = 4 × 105. An Acoustic Doppler Velocimeter (ADV) is installed one turbine diameter upstream of the turbine rotation plane to characterize the inflow turbulence. Measurements are obtained at four relative blade tip immersion depths of z/D = 0.5, 0.4, 0.3, and 0.2 at a TSR value of 7 to identify the depth where free surface effects impact overall turbine performance. The overall average power and thrust coefficient are presented and compared to previously conducted baseline tests. The influence of wake expansion blockage on the turbine performance due to presence of the free surface at these immersion depths will also be discussed.

Study of the nonequilibrium state of superconductors by large quasiparticle injection from an external current source

International Nuclear Information System (INIS)

Iguchi, I.

1977-01-01

We have studied the nonequilibrium state of superconductors by injecting large numbers of quasiparticles from an external current source into a superconducting film of a tunnel junction with low tunnel resistance (typically 0.1--1 Ω for junction area approx. = 10 -4 cm 2 ). It was observed that there was a critical tunnel current density at which a voltage appeared locally in the part of a superconducting film confined to the junction area. Its values ranged from 10 2 to 10 3 A/cm 2 for bath temperatures well below T/sub c/. Followed by this voltage onset, a transition region corresponding to the nonequilibrium intermediate resistive state was also observed. For further increase of the tunnel current, the local film resistance developed beyond the value of its normal resistance, suggesting that the nonequilibrium state extends far beyond the voltage onset point. A theory based on the modified Rothwarf-Taylor equations and Parker's T* model is presented to compare with the experimental results. The calculated critical current density yielded almost the same order of magnitude as those found experimentally. The detailed behavior, however, deviates from the theoretical predictions although the film makes a second-order transition in the broad range of temperatures. It is also shown using four-terminal analysis that our observations and those by Wong, Yeh, and Langenberg are essentially the same

Variability of photovoltaic panels efficiency depending on the value of the angle of their inclination relative to the horizon

OpenAIRE

Majdak Marek

2017-01-01

The objective of this paper was to determine the relationship between the efficiency of photovoltaic panels and the value of the angle of their inclination relative to the horizon. For the purpose of experimental research have been done tests on the photovoltaic modules made of monocrystalline, polycrystalline and amorphous silicon. The experiment consisted of measurement of the voltage and current generated by photovoltaic panels at a known value of solar radiation and a specified resistance...

Simulation study and experimental results for detection and classification of the transient capacitor inrush current using discrete wavelet transform and artificial intelligence

Directory of Open Access Journals (Sweden)

Patcharoen Theerasak

2018-04-01

Full Text Available This paper describes the combination of discrete wavelet transforms (DWT and artificial intelligence (AI, which are efficient techniques to identify the type of inrush current, analyze the origin and possible cause on the capacitor bank switching. The experiment setup used to verify the proposed techniques can be detected and classified the transient inrush current from normal capacitor rated current. The discrete wavelet transforms are used to detect and classify the inrush current. Then, output from wavelet is acted as input of fuzzy inference system for discriminating the type of switching transient inrush current. The proposed technique shows enhanced performance with a discrimination accuracy of 90.57%. Both simulation study and experimental results are quite satisfactory with providing the high accuracy and reliability which can be developed and implemented into a numerical overcurrent (50/51 and unbalanced current (60C protection relay for an application of shunt capacitor bank protection in the future.

Simulation study and experimental results for detection and classification of the transient capacitor inrush current using discrete wavelet transform and artificial intelligence

Science.gov (United States)

Patcharoen, Theerasak; Yoomak, Suntiti; Ngaopitakkul, Atthapol; Pothisarn, Chaichan

2018-04-01

This paper describes the combination of discrete wavelet transforms (DWT) and artificial intelligence (AI), which are efficient techniques to identify the type of inrush current, analyze the origin and possible cause on the capacitor bank switching. The experiment setup used to verify the proposed techniques can be detected and classified the transient inrush current from normal capacitor rated current. The discrete wavelet transforms are used to detect and classify the inrush current. Then, output from wavelet is acted as input of fuzzy inference system for discriminating the type of switching transient inrush current. The proposed technique shows enhanced performance with a discrimination accuracy of 90.57%. Both simulation study and experimental results are quite satisfactory with providing the high accuracy and reliability which can be developed and implemented into a numerical overcurrent (50/51) and unbalanced current (60C) protection relay for an application of shunt capacitor bank protection in the future.

The count of losses by eddy currents in the windings of electric motors with hollow anchor

Directory of Open Access Journals (Sweden)

N. V. Pribylova

2017-01-01

Full Text Available Given the rationale of taking into account losses on eddy currents in the windings of a low-inertia DC motors with offered magnetoelectric systems. Increased in recent years, the power of these motors (through the use of highly coercive magnets permanent caused an increase in the volume of copper in the air gap and the magnetic induction values. All this has values given rise to significant eddy currents in the windings made in the air gap, and hence the necessity of taking into account losses from these currents. The experimentally obtained dependence of the losses on eddy currents on the frequency of rotation for a DC motor with a hollow anchor with a power of 350 watts. The magnitude of these losses can reach 30% of the nominal power of the motor. Described mechanism of occurrence of losses. Eddy currents occur in areas with variable magnetic flux and cause the appearance of force, which is directed toward the velocity vector and inhibits the anchor. The directions of these currents, the vectors of magnetic induction, magnetic field and force acting on the conductor winding and a braking anchor. The proposed methods reduce losses: crushing contours of eddy currents and achieve uniform distribution of magnetic induction in the interpolar space of the motor. Shows their strengths and weaknesses. The crushing circuits of windings occur surge currents. To eliminate the losses on the surge currents it is necessary to apply a transposition of the conductors. Given a refined formula for finding the losses on eddy currents in the armature winding, the conductors of which is made in the form of a harness of several wires. Formula has shown a good convergence with experimental data.

Experimental study of falling water limitation under counter-current flow in the vertical rectangular channel

International Nuclear Information System (INIS)

Usui, Tohru; Kaminaga, Masanori; Sudo, Yukio.

1988-07-01

Quantitative understanding of critical heat flux (CHF) in the narrow vertical rectangular channel is required for the thermo-hydroulic design and the safety analysis of research reactors in which flat-plate-type fuel is adopted. Especially, critical heat flux under low downward velocity has a close relation with falling water limitation under counter-current flow. Accordingly, CCFL (Counter-current Flow Limitation) experiments were carried out for both vertical rectangular channels and vertical circular tubes varried in their size and configuration of their cross sections, to make clear CCFL characteristics in the vertical rectangular channels. In the experiments, l/de of the rectangular channel was changed from 3.5 to 180. As the results, it was clear that different equivalent hydraulic diameter de, namely width or water gap of channel, gave different CCFL characteristics of rectangular channel. But the influence of channel length l on CCFL characteristics was not observed. Besides, a dimensionless correlation to estimate a relation between upward air velocity and downward water velocity was proposed based on the present experimental results. The difference of CCFL characteristics between rectangular channels and circular tubes was also investigated. Especially for the rectangular channels, dry-patches appearing condition was made clear as a flow-map. (author)

Is fair value currently in compliance with the principle of true and real reflection in the Czech accounting?

Directory of Open Access Journals (Sweden)

Jana Gláserová

2012-01-01

Full Text Available Information value of data provided by the accounting is in significant extent dependent on the method of valuation used in accounting of individual economic operations especially on the method of valuation of individual items in the financial statements. Financial expression of the individual value of assets and liabilities of the company (including the balance sheet of the company, as well as the amount of equity, depend just on specific method of valuation of assets and liabilities that each entity used in the accounting system. This fact has also a crucial influence on the overall level of financial analysis since mostly aggregated data in the appropriate valuation gained from various parts of the financial statements are the input data for financial analysis.Certain items of assets and liabilities are valued at fair value at the balance sheet day in the Czech accounting in compliance with the global developments. The concept of fair value in Czech accounting is regulated by Czech Accounting Act in § 27 paragraph 4 and 5. The Czech regulation of the concept of the fair value is based on its detailed definition of the IAS / IFRS, including cases of practical use.The aim of this paper is to answer the question whether currently the fair value in the Czech accounting reflects the reality, based on definition of its content in accordance with applicable legal regulation. Partial aim is to identify specific cases of its application in the accounting of various types of business entities in the Czech Republic in existing practice. The paper also identifies methodological procedure of recording changes resulting from the valuation or revaluation of various types of assets at fair value, including their impacts on the financial statements. An integral part of the paper is the perspective of IAS / IFRS on fair value in accounting, so the definition of the fair value and also there is historical development of valuation of assets according to IAS

Experiments with eddy currents: the eddy current brake

International Nuclear Information System (INIS)

Gonzalez, Manuel I

2004-01-01

A moderate-cost experimental setup is presented to help students to understand some qualitative and quantitative aspects of eddy currents. The setup operates like an eddy current brake, a device commonly used in heavy vehicles to dissipate kinetic energy by generating eddy currents. A set of simple experiments is proposed to measure eddy current losses and to relate them to various relevant parameters. Typical results for each of the experiments are presented, and comparisons with theoretical predictions are included. The experiments, which are devoted to first-year undergraduate students, deal also with other pedagogically relevant topics in electricity and magnetism, such as basic laws, electrical measurement techniques, the sources of the magnetic field and others

Current status of baryon spectroscopy

International Nuclear Information System (INIS)

Wali, K.C.

1975-08-01

In this review of baryon spectroscopy, the basic ideas of some of the current models and the experimental data for their claims to success are discussed including realistic or constituent quark models, experimental comparison, the experimental and theoretical basis for the assignments, algebraic quark models, and confinement schemes

Spin currents in metallic nanostructures

Energy Technology Data Exchange (ETDEWEB)

Czeschka, Franz Dominik

2011-09-05

A pure spin current, i.e., a flow of angular momentum without accompanying net charge current, is a key ingredient in the field of spintronics. In this thesis, we experimentally investigated two different concepts for pure spin current sources suggested by theory. The first is based on a time-dependent magnetization precession which ''pumps'' a pure spin current into an adjacent non-magnetic conductor. Our experiments quantitatively corroborated important predictions expected theoretically for this approach, including the dependence of the spin current on the sample geometry and the microwave power. Even more important, we could show for the first time that the spin pumping concept is viable in a large variety of ferromagnetic materials and that it only depends on the magnetization damping. Therefore, our experiments established spin pumping as generic phenomenon and demonstrated that it is a powerful way to generate pure spin currents. The second theoretical concept is based on the conversion of charge currents into spin currents in non-magnetic nanostructures via the spin Hall effect. We experimentally investigated this approach in H-shaped, metallic nanodevices, and found that the predictions are linked to requirements not realizable with the present experimental techniques, neither in sample fabrication nor in measurement technique. Indeed, our experimental data could be consistently understood by a spin-independent transport model describing the transition from diffusive to ballistic transport. In addition, the implementation of advanced fabrication and measurement techniques allowed to discover a new non-local phenomenon, the non-local anisotropic magnetoresistance. Finally, we also studied spin-polarized supercurrents carried by spin-triplet Cooper pairs. We found that low resistance interfaces are a key requirement for further experiments in this direction. (orig.)

Thermal studies of a superconducting current limiter using Monte-Carlo method

International Nuclear Information System (INIS)

Leveque, J.; Rezzoug, A.

1999-01-01

Considering the increase of the fault current level in electrical network, the current limiters become very interesting. The superconducting limiters are based on the quasi-instantaneous intrinsic transition from superconducting state to normal resistive one. Without detection of default or given order, they reduce the constraints supported by electrical installations above the fault. To avoid the destruction of the superconducting coil, the temperature must not exceed a certain value. Therefore the design of a superconducting coil needs the simultaneous resolution of an electrical equation and a thermal one. This papers deals with a resolution of this coupled problem by the method of Monte-Carlo. This method allows us to calculate the evolution of the resistance of the coil as well as the current of limitation. Experimental results are compared with theoretical ones. (orig.)

Current measurement method for characterization of fast switching power semiconductors with Silicon Steel Current Transformer

DEFF Research Database (Denmark)

Li, Helong; Beczkowski, Szymon; Munk-Nielsen, Stig

2015-01-01

This paper proposes a novel current measurement method with Silicon Steel Current Transformer (SSCT) for the characterization of fast switching power semiconductors. First, the existing current sensors for characterization of fast switching power semiconductors are experimentally evaluated...

BirdsEyeView (BEV: graphical overviews of experimental data

Directory of Open Access Journals (Sweden)

Zhang Lifeng

2012-09-01

Full Text Available Abstract Background Analyzing global experimental data can be tedious and time-consuming. Thus, helping biologists see results as quickly and easily as possible can facilitate biological research, and is the purpose of the software we describe. Results We present BirdsEyeView, a software system for visualizing experimental transcriptomic data using different views that users can switch among and compare. BirdsEyeView graphically maps data to three views: Cellular Map (currently a plant cell, Pathway Tree with dynamic mapping, and Gene Ontology http://www.geneontology.org Biological Processes and Molecular Functions. By displaying color-coded values for transcript levels across different views, BirdsEyeView can assist users in developing hypotheses about their experiment results. Conclusions BirdsEyeView is a software system available as a Java Webstart package for visualizing transcriptomic data in the context of different biological views to assist biologists in investigating experimental results. BirdsEyeView can be obtained from http://metnetdb.org/MetNet_BirdsEyeView.htm.

Experimental Guidance for Isospin Symmetry Breaking Calculations via Single Neutron Pickup Reactions

Science.gov (United States)

Leach, K. G.; Garrett, P. E.; Bangay, J. C.; Bianco, L.; Demand, G. A.; Finlay, P.; Green, K. L.; Phillips, A. A.; Rand, E. T.; Sumithrarachchi, C. S.; Svensson, C. E.; Triambak, S.; Wong, J.; Ball, G.; Faestermann, T.; Krücken, R.; Hertenberger, R.; Wirth, H.-F.; Towner, I. S.

2013-03-01

Recent activity in superallowed isospin-symmetry-breaking correction calculations has prompted interest in experimental confirmation of these calculation techniques. The shellmodel set of Towner and Hardy (2008) include the opening of specific core orbitals that were previously frozen. This has resulted in significant shifts in some of the δC values, and an improved agreement of the individual corrected {F}t values with the adopted world average of the 13 cases currently included in the high-precision evaluation of Vud. While the nucleus-to-nucleus variation of {F}t is consistent with the conserved-vector-current (CVC) hypothesis of the Standard Model, these new calculations must be thoroughly tested, and guidance must be given for their improvement. Presented here are details of a 64Zn(ěcd, t)63Zn experiment, undertaken to provide such guidance.

The baryon vector current in the combined chiral and 1/Nc expansions

Energy Technology Data Exchange (ETDEWEB)

Flores-Mendieta, Ruben; Goity, Jose L [JLAB

2014-12-01

The baryon vector current is computed at one-loop order in large-Nc baryon chiral perturbation theory, where Nc is the number of colors. Loop graphs with octet and decuplet intermediate states are systematically incorporated into the analysis and the effects of the decuplet-octet mass difference and SU(3) flavor symmetry breaking are accounted for. There are large-Nc cancellations between different one-loop graphs as a consequence of the large-Nc spin-flavor symmetry of QCD baryons. The results are compared against the available experimental data through several fits in order to extract information about the unknown parameters. The large-Nc baryon chiral perturbation theory predictions are in very good agreement both with the expectations from the 1/Nc expansion and with the experimental data. The effect of SU(3) flavor symmetry breaking for the |Delta S|=1 vector current form factors f1(0) results in a reduction by a few percent with respect to the corresponding SU(3) symmetric values.

Experimental program at Fermilab

International Nuclear Information System (INIS)

Jovanovic, D.

1974-01-01

The experimental program at Fermilab is briefly surveyed: accelerators and experimental areas, current experiments such as elastic scattering of π +- , K +- , p +- , on proton and deuteron total cross sections, neutrino physics, high transverse momentum [fr

Core Values: A History of Values-Related Initiatives in the Air Force

National Research Council Canada - National Science Library

Dierker, Gregory

1997-01-01

.... This study specifically examines two of the assumptions made in the current Air Force Core Values initiative against the historic values-related initiatives to identify any differences that have occurred over time...

Issues in neutral currents

International Nuclear Information System (INIS)

Sehgal, L.M.

1980-01-01

The experimental results on low energy confirming the structure of the effective Lagrangian of the weak neutral current processes as predicted by the Salam-Weinberg model are reviewed. Some possible modifications of the effective Lagrangian and the feasibility of their experimental verification are also considered. (P.L.)

Transient current in a quantum dot asymmetrically coupled to metallic leads

International Nuclear Information System (INIS)

Goker, A; Friedman, B A; Nordlander, P

2007-01-01

The time-dependent non-crossing approximation is used to study the transient current in a single-electron transistor attached asymmetrically to two leads following a sudden change in the energy of the dot level. We show that for asymmetric coupling, sharp features in the density of states of the leads can induce oscillations in the current through the dot. These oscillations persist to much longer timescales than the timescale for charge fluctuations. The amplitude of the oscillations increases as the temperature or source-drain bias across the dot is reduced and saturates for values below the Kondo temperature. We discuss the microscopic origin of these oscillations and comment on the possibility for their experimental detection

Experimental study of a high-current FEM with a broadband microwave system

Energy Technology Data Exchange (ETDEWEB)

Denisov, G.G.; Bratman, V.L.; Ginzburg, N.S. [Institute of Applied Physics, Nizhny Novgorod (Russian Federation)] [and others

1995-12-31

One of the main features of FELs and FEMs is the possibility of fast and wideband tuning of the resonant frequency of active media, which can be provided by changing the particle energy. For a frequency adjustable FEM-oscillator, a broadband microwave system, which is simply combined with an electron-optical FEM system and consists of an oversized waveguide and reflectors based on the microwave beams multiplication effect has been proposed and studied successfully in {open_quotes}cold{close_quotes} measurements. Here, the operating ability of a cavity, that includes some key elements of the broadband microwave system, was tested in the presence of an electron beam. To provide large particle oscillation velocities in a moderate undulator field and the presence of a guide magnetic field, the FEM operating regime of double resonance was chosen. In this regime the cyclotron as well as undulator resonance conditions were satisfied. The FEM-oscillator was investigated experimentally on a high-current accelerator {open_quotes}Sinus-6{close_quotes} that forms an electron beam with particle energy 500keV and pulse duration 25ns. The aperture with a diameter 2.5mm at the center of the anode allows to pass through only the central fraction of the electron beam with a current about 100A and a small spread of longitudinal velocities of the particles. Operating transverse velocity was pumped into the electron beam in the pulse plane undulator of a 2.4cm period. The cavity with a frequency near 45GHz consists of a square waveguide and two reflectors. The broadband up-stream reflector based on the multiplication effect had the power reflectivity coefficient more than 90% in the frequency band 10% for the H{sup 10} wave of the square waveguide with the maximum about 100% at a frequency 45GHz. The down-stream narrow-band Bragg reflector had the power reflection coefficient approximately 80% in the frequency band of 4% near 45GHz for the operating mode.

Study of non-inductive current drive using high energy neutral beam injection on JT-60U

International Nuclear Information System (INIS)

Oikawa, Toshihiro

2004-01-01

The negative ion based neutral beam (N-NB) current drive was experimentally studied. The N-NB driven current density was determined over a wide range of electron temperatures by using the motional Stark effect spectroscopy. Theoretical prediction of the NB current drive increasing with beam energy and electron temperature was validated. A record value of NB current drive efficiency 1.55 x 10 19 Am -2 W -1 was achieved simultaneously with high confinement and high beta at at a plasma current of 1.5 MA under a fully non-inductively current driven condition. The experimental validation of NB current drive theory for MHD quiescent plasmas gives greater confidence in predicting the NB current drive in future reactors. However, it was also found that MHD instabilities caused a degradation of NB current drive. A beam-driven instability expelled N-NB fast ions carrying non-inductive current from the central region. The lost N-NB driven current was estimated to be 7% of the total N-NB driven current. For the neoclassical tearing mode (NTM), comparisons of the measured neutron yield and fast ion pressure profile with transport code calculations revealed that the loss of fast ions increases with the NTM activity and that fast ions at higher energies suffer larger transport than at lower energies. (author)

Fair market value

International Nuclear Information System (INIS)

Williams, J.

1991-01-01

This paper presents an examination of fair market value concepts as they pertain to producing petroleum properties. conventional petroleum economic theories of fair market value are examined in light of recent work on the market value of long-life reserves. Their work is expanded to show that sellers rely on comparable sales data for estimating FMV. Both results are used to suggest that current practices over-emphasize the discounted cash flow approach to estimating fair market value

Effect of sheath material on critical current characteristics of MgB2 at high temperatures

International Nuclear Information System (INIS)

Kiuchi, M.; Yamauchi, K.; Kurokawa, T.; Otabe, E.S.; Matsushita, T.; Okada, M.; Tanaka, K.; Kumakura, H.; Kitaguchi, H.

2004-01-01

Critical current density and irreversibility field were measured at various temperatures and magnetic fields for MgB 2 PIT tape specimens with different sheaths materials. The experimental results were compared with theoretical estimations using the flux creep-flow model. It is found that the hardness of sheath material indirectly affects the pinning property only through the packing density of MgB 2 . It is considered that the critical current density is mainly determined by a low value of distributed local critical current density determined by grain connectivity. On the other hand, the irreversibility field which is approximately the same among the three tapes is mainly determined by the average pinning strength

Experimental investigation of H2/D2 isotope separation by cryo-adsorption in metal-organic frameworks

International Nuclear Information System (INIS)

Teufel, Julia Sonja

2012-01-01

Light-gas isotopes differ in their adsorption behavior under cryogenic conditions in nanoporous materials due to their difference in zero-point energy. However, the applicability of these cryo-effects for the separation of isotope mixtures is still lacking an experimental proof. The current work describes the first experimentally obtained H 2 /D 2 selectivity values of nanoporous materials measured by applying isotope mixtures in low-temperature thermal desorption spectroscopy (TDS). The dissertation contains the following key points: 1) A proof of the experimental method, i.e. it is shown that TDS leads to reasonable selectivity values. 2) A series of small-pore MFU-4 derivatives (MOFs) is shown to separate isotope mixtures by quantum sieving, i.e. by the difference in the adsorption kinetics. The influence of the pore size on the selectivity is studied systematically for this series. 3) Two MOFs with pores much larger than the kinetic diameter of H 2 do not exhibit kinetic quantum sieving. However, if the MOFs are exposed to an isotope mixture, deuterium adsorbs preferentially at the adsorption sites with high heats of adsorption. According to the experimental results, these strong adsorption sites can be every selective for deuterium. On the basis of the experimentally obtained selectivity values, technical implementations for H 2 /D 2 light-gas isotope separation by cryo-adsorption are described.

Issues in Fair Value Accounting under IFRS

OpenAIRE

Bischof, Jannis

2008-01-01

The dissertation presents theoretical evidence for inconsistencies in fair value accounting under IFRS, experimental evidence for biases in risk perception of fair values and empirical evidence for discretion in banks' disclosure policies with respect to fair value measurement.

Upgrade of the Gas Flow Control System of the Resistive Current Leads of the LHC Inner Triplet Magnets: Simulation and Experimental Validation

CERN Document Server

Perin, A; Casas-Cubillos, J; Pezzetti, M

2014-01-01

The 600 A and 120 A circuits of the inner triplet magnets of the Large Hadron Collider are powered by resistive gas cooled current leads. The current solution for controlling the gas flow of these leads has shown severe operability limitations. In order to allow a more precise and more reliable control of the cooling gas flow, new flowmeters will be installed during the first long shutdown of the LHC. Because of the high level of radiation in the area next to the current leads, the flowmeters will be installed in shielded areas located up to 50 m away from the current leads. The control valves being located next to the current leads, this configuration leads to long piping between the valves and the flowmeters. In order to determine its dynamic behaviour, the proposed system was simulated with a numerical model and validated with experimental measurements performed on a dedicated test bench.

Upgrade of the gas flow control system of the resistive current leads of the LHC inner triplet magnets: Simulation and experimental validation

Energy Technology Data Exchange (ETDEWEB)

Perin, A.; Casas-Cubillos, J.; Pezzetti, M. [CERN, CH-1211 Geneva 23 (Switzerland); Almeida, M. [Universidade Federal de Minas Gerais, 31270-901 Belo Horizonte (Brazil)

2014-01-29

The 600 A and 120 A circuits of the inner triplet magnets of the Large Hadron Collider are powered by resistive gas cooled current leads. The current solution for controlling the gas flow of these leads has shown severe operability limitations. In order to allow a more precise and more reliable control of the cooling gas flow, new flowmeters will be installed during the first long shutdown of the LHC. Because of the high level of radiation in the area next to the current leads, the flowmeters will be installed in shielded areas located up to 50 m away from the current leads. The control valves being located next to the current leads, this configuration leads to long piping between the valves and the flowmeters. In order to determine its dynamic behaviour, the proposed system was simulated with a numerical model and validated with experimental measurements performed on a dedicated test bench.

Current status of the scientific study of the personality disorders: an overview of epidemiological, longitudinal, experimental psychopathology, and neurobehavioral perspectives.

Science.gov (United States)

Lenzenweger, Mark F

2010-08-01

Research on the nature and development of personality disorders has grown immensely over the past thirty years. A selective summary overview is given of the current status of the scientific study of the personality disorders from several perspectives, including the epidemiological, longitudinal, experimental psychopathology, and neurobehavioral perspectives. From this research, we now know that approximately 10 percent of the general population suffer from a diagnosable personality disorder. Moreover, contrary to nearly a century of theory and clinical pedagogy, modern longitudinal studies clearly suggest that personality disorders decrease in severity over time. The mechanisms by which this change occurs are not understood at present, though it is not likely that change in underlying normal personality systems drives the change in personality disorder. The methods of the experimental psychopathology laboratory, including neuroimaging approaches, are being brought to bear on the nature of personality disorders in efforts to relate neurobiological and neurocognitive functions to personality disorder symptomatology. A model that links personality disorder feature development to underlying, interacting brain-based neurobehavioral systems is reviewed in brief. Current issues and findings illustrative of these developments are given using borderline personality disorder as an exemplar. Finally, areas of intersection between psychoanalytic treatment approaches and the growing science of personality disorder are highlighted.

Experimental observations and theoretical models for beam-beam phenomena

Energy Technology Data Exchange (ETDEWEB)

Kheifets, S.

1981-03-01

The beam-beam interaction in storage rings exhibits all the characteristics of nonintegrable dynamical systems. Here one finds all kinds of resonances, closed orbits, stable and unstable fixed points, stochastic layers, chaotic behavior, diffusion, etc. The storage ring itself being an expensive device nevertheless while constructed and put into operation presents a good opportunity of experimentally studying the long-time behavior of both conservative (proton machines) and nonconservative (electron machines) dynamical systems - the number of bunch-bunch interactions routinely reaches values of 10/sup 10/-10/sup 11/ and could be increased by decreasing the beam current. At the same time the beam-beam interaction puts practical limits for the yield of the storage ring. This phenomenon not only determines the design value of main storage ring parameters (luminosity, space charge parameters, beam current), but also in fact prevents many of the existing storage rings from achieving design parameters. Hence, the problem has great practical importance along with its enormous theoretical interest. A brief overview of the problem is presented.

Experimental observations and theoretical models for beam-beam phenomena

International Nuclear Information System (INIS)

Kheifets, S.

1981-03-01

The beam-beam interaction in storage rings exhibits all the characteristics of nonintegrable dynamical systems. Here one finds all kinds of resonances, closed orbits, stable and unstable fixed points, stochastic layers, chaotic behavior, diffusion, etc. The storage ring itself being an expensive device nevertheless while constructed and put into operation presents a good opportunity of experimentally studying the long-time behavior of both conservative (proton machines) and nonconservative (electron machines) dynamical systems - the number of bunch-bunch interactions routinely reaches values of 10 10 -10 11 and could be increased by decreasing the beam current. At the same time the beam-beam interaction puts practical limits for the yield of the storage ring. This phenomenon not only determines the design value of main storage ring parameters (luminosity, space charge parameters, beam current), but also in fact prevents many of the existing storage rings from achieving design parameters. Hence, the problem has great practical importance along with its enormous theoretical interest. A brief overview of the problem is presented

Optimization and control of the plasma shape and current profile in noncircular cross-section tokamaks

International Nuclear Information System (INIS)

Moore, R.W.; Bernard, L.C.; Chan, V.S.; Davidson, R.H.; Dobrott, D.R.; Helton, F.J.; Miller, R.L.; Pfeiffer, W.; Waltz, R.E.; Wang, T.S.

1980-06-01

High-β equilibria which are stable to all ideal MHD modes are found by optimizing the plasma shape and current profile for doublets, up-down asymmetric dees, and symmetric dees. The ideal MHD stability of these equilibria for low toroidal mode number n is analyzed with a global MHD stability code, GATO. The stability to high-n modes is analyzed with a localized ballooning code, BLOON. The attainment of high β is facilitated by an automated optimization search on shape and current parameters. The equilibria are calculated with a free-boundary equilibrium code using coils appropriate for the Doublet III experimental device. The optimal equilibria are characterized by broad current profiles with values of β/sub poloidal/ approx. =1. Experimental realization of the shapes and current profiles giving the highest β limits is explored with a 1 1/2-D transport code, which simulates the time evolution of the 2-D MHD equilibrium while calculating consistent current profiles from a 1-D transport model. Transport simulations indicate that nearly optimal shapes may be obtained provided that the currents in the field-shaping coils are appropriately programmed and the plasma current profile is sufficiently broad. Obtaining broad current profiles is possible by current ramping, neutral beam heating, and electron cyclotron heating. With combinations of these techniques it is possible to approach the optimum β predicted by the MHD theory

Pillars of cooperation: Honesty-Humility, social value orientations, and economic behavior

DEFF Research Database (Denmark)

Hilbig, B.E.; Zettler, Ingo

2009-01-01

The current work explores the predictive power of the recently proposed sixth personality dimension, Honesty-Humility, with respect to economic and cooperative behavior. It was expected that this factor should explain how decision makers allocate a valued good to themselves vs. another in the dic......The current work explores the predictive power of the recently proposed sixth personality dimension, Honesty-Humility, with respect to economic and cooperative behavior. It was expected that this factor should explain how decision makers allocate a valued good to themselves vs. another...... in the dictator and the ultimatum game. More importantly, we predicted that Honesty-Humility would explain differences between these games in which the power of the recipient to retaliate is varied. Both conjectures were corroborated in a semi-experimental study with N = 134 participants: individuals low...... in Honesty-Humility made more selfish decisions and only shifted towards a more fair allocation whenever the other was empowered to punish defection. Those high in Honesty-Humility, on the other hand, displayed a stable tendency for choosing a more fair solution - even when they could have defected without...

Condition for the occurrence of phase slip centers in superconducting nanowires under applied current or voltage

DEFF Research Database (Denmark)

Michotte, S.; Mátéfi-Tempfli, Stefan; Piraux, L.

2004-01-01

Experimental results on the phase slip process in superconducting lead nanowires are presented under two different experimental conditions: constant applied current or constant voltage. Based on these experiments we established a simple model which gives us the condition of the appearance of phase...... slip centers in a quasi-one-dimensional wire. The competition between two relaxations times (relaxation time of the absolute value of the order parameter τ and relaxation time of the phase of the order parameter in the phase slip center τ) governs the phase slip process. Phase slips, as periodic...... oscillations in time of the order parameter, are only possible if the gradient of the phase grows faster than the value of the order parameter in the phase slip center, or equivalently if τ≤ τ....

A matrix model for valuing anesthesia service with the resource-based relative value system.

Science.gov (United States)

Sinclair, David R; Lubarsky, David A; Vigoda, Michael M; Birnbach, David J; Harris, Eric A; Behrens, Vicente; Bazan, Richard E; Williams, Steve M; Arheart, Kristopher; Candiotti, Keith A

2014-01-01

The purpose of this study was to propose a new crosswalk using the resource-based relative value system (RBRVS) that preserves the time unit component of the anesthesia service and disaggregates anesthesia billing into component parts (preoperative evaluation, intraoperative management, and postoperative evaluation). The study was designed as an observational chart and billing data review of current and proposed payments, in the setting of a preoperative holing area, intraoperative suite, and post anesthesia care unit. In total, 1,195 charts of American Society of Anesthesiology (ASA) physical status 1 through 5 patients were reviewed. No direct patient interventions were undertaken. Spearman correlations between the proposed RBRVS billing matrix payments and the current ASA relative value guide methodology payments were strong (r=0.94-0.96, Pbilling matrix yielded payments that were 3.0%±1.34% less than would have been expected from commercial insurers, using standard rates for commercial ASA relative value units and RBRVS relative value units. Compared with current Medicare reimbursement under the ASA relative value guide, reimbursement would almost double when converting to an RBRVS billing model. The greatest increases in Medicare reimbursement between the current system and proposed billing model occurred as anesthetic management complexity increased. The new crosswalk correlates with existing evaluation and management and intensive care medicine codes in an essentially revenue neutral manner when applied to the market-based rates of commercial insurers. The new system more highly values delivery of care to more complex patients undergoing more complex surgery and better represents the true value of anesthetic case management.

Building Evidence of Validity: The Relation between Work Values, Interests, Personality, and Personal Values

Science.gov (United States)

Leuty, Melanie E.; Hansen, Jo-Ida C.

2013-01-01

The current study used work values components (WVC) to examine the relationship between work values, vocational interests, personality, and personal values. Most intercorrelations between work values and other constructs were in the small effect range. Overall correlations between scale scores provided evidence of convergent and discriminant…

Model-independent study of light cone current commutators

International Nuclear Information System (INIS)

Gautam, S.R.; Dicus, D.A.

1974-01-01

An attempt is made to extract information on the nature of light cone current commutators (L. C. C.) in a model independent manner. Using simple assumptions on the validity of the DGS representation for the structure functions of deep inelastic scattering and using the Bjorken--Johnston--Low theorem it is shown that in principle the L. C. C. may be constructed knowing the experimental electron--proton scattering data. On the other hand the scaling behavior of the structure functions is utilized to study the consistency of a vanishing value for various L. C. C. under mild assumptions on the behavior of the DGS spectral moments. (U.S.)

They see a rat, we seek a cure for diseases: the current status of animal experimentation in medical practice.

Science.gov (United States)

Kehinde, Elijah O

2013-01-01

The objective of this review article was to examine current and prospective developments in the scientific use of laboratory animals, and to find out whether or not there are still valid scientific benefits of and justification for animal experimentation. The PubMed and Web of Science databases were searched using the following key words: animal models, basic research, pharmaceutical research, toxicity testing, experimental surgery, surgical simulation, ethics, animal welfare, benign, malignant diseases. Important relevant reviews, original articles and references from 1970 to 2012 were reviewed for data on the use of experimental animals in the study of diseases. The use of laboratory animals in scientific research continues to generate intense public debate. Their use can be justified today in the following areas of research: basic scientific research, use of animals as models for human diseases, pharmaceutical research and development, toxicity testing and teaching of new surgical techniques. This is because there are inherent limitations in the use of alternatives such as in vitro studies, human clinical trials or computer simulation. However, there are problems of transferability of results obtained from animal research to humans. Efforts are on-going to find suitable alternatives to animal experimentation like cell and tissue culture and computer simulation. For the foreseeable future, it would appear that to enable scientists to have a more precise understanding of human disease, including its diagnosis, prognosis and therapeutic intervention, there will still be enough grounds to advocate animal experimentation. However, efforts must continue to minimize or eliminate the need for animal testing in scientific research as soon as possible. © 2013 S. Karger AG, Basel.

Modified Vaccinia Virus Ankara: History, Value in Basic Research, and Current Perspectives for Vaccine Development.

Science.gov (United States)

Volz, A; Sutter, G

2017-01-01

Safety tested Modified Vaccinia virus Ankara (MVA) is licensed as third-generation vaccine against smallpox and serves as a potent vector system for development of new candidate vaccines against infectious diseases and cancer. Historically, MVA was developed by serial tissue culture passage in primary chicken cells of vaccinia virus strain Ankara, and clinically used to avoid the undesirable side effects of conventional smallpox vaccination. Adapted to growth in avian cells MVA lost the ability to replicate in mammalian hosts and lacks many of the genes orthopoxviruses use to conquer their host (cell) environment. As a biologically well-characterized mutant virus, MVA facilitates fundamental research to elucidate the functions of poxvirus host-interaction factors. As extremely safe viral vectors MVA vaccines have been found immunogenic and protective in various preclinical infection models. Multiple recombinant MVA currently undergo clinical testing for vaccination against human immunodeficiency viruses, Mycobacterium tuberculosis or Plasmodium falciparum. The versatility of the MVA vector vaccine platform is readily demonstrated by the swift development of experimental vaccines for immunization against emerging infections such as the Middle East Respiratory Syndrome. Recent advances include promising results from the clinical testing of recombinant MVA-producing antigens of highly pathogenic avian influenza virus H5N1 or Ebola virus. This review summarizes our current knowledge about MVA as a unique strain of vaccinia virus, and discusses the prospects of exploiting this virus as research tool in poxvirus biology or as safe viral vector vaccine to challenge existing and future bottlenecks in vaccinology. © 2017 Elsevier Inc. All rights reserved.

Experimental and numerical assessment of low-frequency current distributions from UMTS and GSM mobile phones

International Nuclear Information System (INIS)

Gosselin, Marie-Christine; Kühn, Sven; Kuster, Niels

2013-01-01

The evaluation of the exposure from mobile communication devices requires consideration of electromagnetic fields (EMFs) over a broad frequency range from dc to GHz. Mobile phones in operation have prominent spectral components in the low-frequency (LF) and radio-frequency (RF) ranges. While the exposure to RF fields from mobile phones has been comprehensively assessed in the past, the LF fields have received much less attention. In this study, LF fields from mobile phones are assessed experimentally and numerically for the global system for mobile (GSM) and universal mobile telecommunications system (UMTS) communication systems and conclusions about the global (LF and RF) EMF exposure from both systems are drawn. From the measurements of the time-domain magnetic fields, it was found that the contribution from the audio signal at a normal speech level, i.e., −16 dBm0, is the same order of magnitude as the fields induced by the current bursts generated from the implementation of the GSM communication system at maximum RF output level. The B-field induced by currents in phones using the UMTS is two orders of magnitude lower than that induced by GSM. Knowing that the RF exposure from the UMTS is also two orders of magnitude lower than from GSM, it is now possible to state that there is an overall reduction of the exposure from this communication system. (paper)

Experimental and numerical assessment of low-frequency current distributions from UMTS and GSM mobile phones

Science.gov (United States)

Gosselin, Marie-Christine; Kühn, Sven; Kuster, Niels

2013-12-01

The evaluation of the exposure from mobile communication devices requires consideration of electromagnetic fields (EMFs) over a broad frequency range from dc to GHz. Mobile phones in operation have prominent spectral components in the low-frequency (LF) and radio-frequency (RF) ranges. While the exposure to RF fields from mobile phones has been comprehensively assessed in the past, the LF fields have received much less attention. In this study, LF fields from mobile phones are assessed experimentally and numerically for the global system for mobile (GSM) and universal mobile telecommunications system (UMTS) communication systems and conclusions about the global (LF and RF) EMF exposure from both systems are drawn. From the measurements of the time-domain magnetic fields, it was found that the contribution from the audio signal at a normal speech level, i.e., -16 dBm0, is the same order of magnitude as the fields induced by the current bursts generated from the implementation of the GSM communication system at maximum RF output level. The B-field induced by currents in phones using the UMTS is two orders of magnitude lower than that induced by GSM. Knowing that the RF exposure from the UMTS is also two orders of magnitude lower than from GSM, it is now possible to state that there is an overall reduction of the exposure from this communication system.

Comparison the Results of Numerical Simulation And Experimental Results for Amirkabir Plasma Focus Facility

Science.gov (United States)

Goudarzi, Shervin; Amrollahi, R.; Niknam Sharak, M.

2014-06-01

In this paper the results of the numerical simulation for Amirkabir Mather-type Plasma Focus Facility (16 kV, 36μF and 115 nH) in several experiments with Argon as working gas at different working conditions (different discharge voltages and gas pressures) have been presented and compared with the experimental results. Two different models have been used for simulation: five-phase model of Lee and lumped parameter model of Gonzalez. It is seen that the results (optimum pressures and current signals) of the Lee model at different working conditions show better agreement than lumped parameter model with experimental values.

Comparison the results of numerical simulation and experimental results for Amirkabir plasma focus facility

International Nuclear Information System (INIS)

Goudarzi, Shervin; Amrollahi, R; Sharak, M Niknam

2014-01-01

In this paper the results of the numerical simulation for Amirkabir Mather-type Plasma Focus Facility (16 kV, 36μF and 115 nH) in several experiments with Argon as working gas at different working conditions (different discharge voltages and gas pressures) have been presented and compared with the experimental results. Two different models have been used for simulation: five-phase model of Lee and lumped parameter model of Gonzalez. It is seen that the results (optimum pressures and current signals) of the Lee model at different working conditions show better agreement than lumped parameter model with experimental values.

Interaction of high-current relativistic electron beams with plasma. Physical nature of the phenomenon and its application in microwave electronics

International Nuclear Information System (INIS)

Rukhadze, A.A.

1981-01-01

Pulsed high-current electron beams with characteristic parameters: electron energy 10 5 -10 7 eV, electron current 10 3 -10 6 A, pulse duration 10 -8 -10 -6 s, beam energy 10 2 -10 6 J and power 10 8 -10 13 W, are widely used in different branches of science and technology such as controlled thermonuclear fusion, relativistic microwave electronics, powerful semiconductors, chemical and gaseous lasers, new principles of heavy-ion acceleration, and long-distance energy transmission. The paper discusses a new branch of science - pulsed high-current electronics, which has its own experimental technique and methods of theoretical analysis. Parts I and II determine what is meant by ''high current'' in an electron beam and calculate the maximum obtainable current values; these calculations are made for the simplest geometrical configurations realizable in practice. Current methods for theoretical analysis of high-current electron beam physics are described, together with classification of current experimental devices for generating such beams according to high-current parameters. The stability of electron beams is discussed and the concept of critical currents is introduced. Part III gives a detailed account of plasma-beam instability which occurs on the interaction of a high-current electron beam with high-density space-limited plasma. The linear and non-linear stages of beam instability are considered. The given theory is used for calculations for amplifiers and microwave generators of electromagnetic radiation. Finally, the experimental achievements in high-current relativistic microwave electronics are reviewed. (author)

Current Monitoring System for ITER Like ICRH Antenna

International Nuclear Information System (INIS)

Argouarch, A.

2006-01-01

On TS antennas, the power transfer optimization from ICRH antenna to Plasma load is performed using feedback internal matching system. Experimental handling is required to mach the reactive impedance accordingly to the fluctuant plasma loading. As part of the development of the new ICRH prototype antenna, an additional measurement system based on Rogowski coils was developed to monitor the current distribution in antenna straps. The objective is to control module and phase of the antenna current straps with measurement provided by the coil system. Matching capacitors values, generators power and phase can also be controlled using the output of the devices, improving the real time matching control of the array. This paper details the new measurement layout, the Rogowski coil, and the whole system connected on each strap design for RF currents measurement between 40 MHz - 60 MHz for maximum amplitude of 1 kA. On the new ICRH prototype antenna, the measurement coils are coupled to the point where the strap currents are short circuited to the frame. The module and phase measurements are performed with the coils by direct magnetic induction in a vacuum and high temperature environment. Also, the Rogowski coils were characterized at low level power with vector network analyzer and the design adapted in order to obtain a controlled and reproducible gain in the desire bandwidth. The transconductive function is established with an experimental gain near -80 dB between primary circuit and inductive signal generated by the Rogowski coil. In a second step, the system with its associated electronic was qualified under high RF power. First results with high RF current (closed to 500 A at 57 MHz) match the desire Rogowski coil response. Compromises with electrical response at low power level and the coil under thermal/RF stresses were the most challenging part of the development. The overall response of the system and the current module/phase measurements are promising. A proper

Is public value pluralism paramount? The intrinsic hybridity and multiplicity of public values

NARCIS (Netherlands)

van der Wal, Z.; van Hout, E.Th.J.

2009-01-01

In current debates on public values too often the assumption is made that unitary conceptions exist of what "public values" are, and that one universal set of classical public core values guides administrative behaviour throughout the public sector. Studies show, however, that it is very hard to

Experimental halls workshop summary

International Nuclear Information System (INIS)

Thorndike, A.

1976-01-01

At the experimental halls workshop, discussions were held on: (1) open areas as compared with enclosed halls; (2) the needs of ep, anti pp, and other options; (3) the hall for the lepton detector; and (4) the hall for the hadron spectrometer. The value of different possibilities for the future experimental program was explored. A number of suggestions emerged which will be used as the design of the experimental halls progresses

Current drive and sustain experiments with the bootstrap current in JT-60

International Nuclear Information System (INIS)

Kikuchi, Mitsuru; Azumi, Masafumi; Tani, Keiji; Tsuji, Shunji; Kubo, Hirotaka

1989-11-01

The current drive and sustain experiments with the neoclassical bootstrap current are performed in the JT-60 tokamak. It is shown that up to 80% of total plasma current is driven by the bootstrap current in extremely high β p regime (β p = 3.2) and the current drive product I p (bootstrap) n-bar e R p up to 4.4 x 10 19 MAm -2 has been attained with the bootstrap current. The experimental resistive loop voltages are compared with the calculations using the neoclassical resistivity with and without the bootstrap current and the Spitzer resistivity for a wide range of the plasma current (I p = 0.5 -2 MA) and the poloidal beta (β p = 0.1 - 3.2). The calculated resistive loop voltage is consistent with the neoclassical prediction including the bootstrap current. Current sustain with the bootstrap current is tested by terminating the I p feedback control during the high power neutral beam heating. An enhancement of the L/R decay time than those expected from the plasma resistivity with measured T e and Zeff has been confirmed experimentally supporting the large non-inductive current in the plasma and is consistent with the neoclassical prediction. A new technique to calculate the bootstrap current in multi-collisionality regime for finite aspect ratio tokamak has bee developed. The neoclassical bootstrap current is calculated directly through the force balance equations between viscous and friction forces according to the Hirshman-Sigmar theory. The bootstrap current driven by the fast ion component is also included. Ballooning stability of the high β p plasma are analyzed using the current profiles including the bootstrap current. The plasma pressure is close to the ballooning limit in high β p discharges. (author)

Value Chain Engineering

DEFF Research Database (Denmark)

Wæhrens, Brian Vejrum; Slepniov, Dmitrij

2015-01-01

This workbook is recommended for the attention of students of and managers in Danish small and medium sized enterprises (SMEs). Danish SMEs are currently facing a number of key challenges related to their position in global value chains. This book provides an insight into value chain management t...

An ϵ' improvement from right-handed currents

International Nuclear Information System (INIS)

Cirigliano, Vincenzo; Dekens, Wouter Gerard; Vries, Jordy de; Mereghetti, Emanuele

2017-01-01

Recent lattice QCD calculations of direct CP violation in K L → ππ decays indicate tension with the experimental results. Assuming this tension to be real, we investigate a possible beyond-the-Standard Model explanation via right-handed charged currents. By using chiral perturbation theory in combination with lattice QCD results, we accurately calculate the modification of ϵ'/ϵ induced by right-handed charged currents and extract values of the couplings that are necessary to explain the discrepancy, pointing to a scale around 10–100 TeV. We find that couplings of this size are not in conflict with constraints from other precision experiments, but next-generation hadronic electric dipole moment searches (such as neutron and 225 Ra) can falsify this scenario. As a result, we work out in detail a direct link, based on chiral perturbation theory, between CP violation in the kaon sector and electric dipole moments induced by right-handed currents which can be used in future analyses of left-right symmetric models.

An exponential scaling law for the strain dependence of the Nb3Sn critical current density

International Nuclear Information System (INIS)

Bordini, B; Alknes, P; Bottura, L; Rossi, L; Valentinis, D

2013-01-01

The critical current density of the Nb 3 Sn superconductor is strongly dependent on the strain applied to the material. In order to investigate this dependence, it is a common practice to measure the critical current of Nb 3 Sn strands for different values of applied axial strain. In the literature, several models have been proposed to describe these experimental data in the reversible strain region. All these models are capable of fitting the measurement results in the strain region where data are collected, but tend to predict unphysical trends outside the range of data, and especially for large strain values. In this paper we present a model of a new strain function, together with the results obtained by applying the new scaling law on relevant datasets. The data analyzed consisted of the critical current measurements at 4.2 K that were carried out under applied axial strain at Durham University and the University of Geneva on different strand types. With respect to the previous models proposed, the new scaling function does not present problems at large strain values, has a lower number of fitting parameters (only two instead of three or four), and is very stable, so that, starting from few experimental points, it can estimate quite accurately the strand behavior in a strain region where there are no data. A relationship is shown between the proposed strain function and the elastic strain energy, and an analogy is drawn with the exponential form of the McMillan equation for the critical temperature. (paper)

Experimental results of current distribution in Rutherford-type LHC cables

CERN Document Server

Verweij, A P

2000-01-01

Current distribution among the wires of multi-strand superconducting cables is an important item for accelerator magnets. A non-uniform distribution could cause additional field distortions in the magnet bore and can as well be one of the reasons of premature quenching. Since two years electrical measurements on superconducting Rutherford-type cables are performed at CERN as part of the reception tests for the Large Hadron Collider (LHC). Cable samples of 2.4 m length are tested at currents up to 32 kA, temperatures around 1.9 and 4.3 K, and fields up to 10 T, applied perpendicularly as well as parallel to the broad face of the cable. Last year, an array of 24 Hall probes was installed in the test set-up in order to measure the self-field of the cable samples along one cable pitch. Each of the probes measures the local field generated by the current in the strands close by, and the results of the all probes reflect therefore the distribution of the strand currents. Experiments are done varying the applied fie...

An experimental study on counter current flow limitation in annular narrow gaps with large diameter

Energy Technology Data Exchange (ETDEWEB)

Park, Rae Joon; Jeong, Ji Whan; Lee, Sung Jin; Cho, Young Ro; Ha, Kwang Sun; Kim, Sang Baik; Kim, Hee Dong [Korea Atomic Energy Research Institute, Taejeon (Korea)

2002-04-01

The present study intends to carry out CCFL experiment with the same gap size as the CHFG facility and suggest an empirical correlation in order to provide basic information useful to development of an empirical critical-power correlation. The present facility consists of water accumulator tank, test section, DC pump, air regulator, valves and sensors. Air and water are used as working fluids. The experiments are carried out at the atmospheric pressure. Differential pressure between the gap ends, liquid and gas phase flow rates, temperature, lower plenum pressure are measured.Measured values are expressed in terms of Wallis' parameter using gap size as a characteristic length. There is a big difference between the present experimental results and the Koizumi et al.'s results, but the present experimental results are very similar to the Richter et al.'s results. The present results agree well with the Osakabe and Kawasaki's results. In comparison of present experiments with the Koizumi et al.'s experiments, gap thickness is similar, but the diameter of the present is bigger than that of Koizumi et al.'s experiments. In comparison of present experiments with the Richter et al.'s experiments, diameter is similar, but the gap thickness of the present is smaller than that of Richter et al.'s experiments. It is judged from these results that correlation development on CCFL to consider gap thickness is reasonable at similar condition of diameter.The developed correlation will be used to develop the CHFG model. 36 refs., 26 figs., 7 tabs. (Author)

Benchmark Evaluation of HTR-PROTEUS Pebble Bed Experimental Program

International Nuclear Information System (INIS)

Bess, John D.; Montierth, Leland; Köberl, Oliver

2014-01-01

Benchmark models were developed to evaluate 11 critical core configurations of the HTR-PROTEUS pebble bed experimental program. Various additional reactor physics measurements were performed as part of this program; currently only a total of 37 absorber rod worth measurements have been evaluated as acceptable benchmark experiments for Cores 4, 9, and 10. Dominant uncertainties in the experimental keff for all core configurations come from uncertainties in the 235 U enrichment of the fuel, impurities in the moderator pebbles, and the density and impurity content of the radial reflector. Calculations of k eff with MCNP5 and ENDF/B-VII.0 neutron nuclear data are greater than the benchmark values but within 1% and also within the 3σ uncertainty, except for Core 4, which is the only randomly packed pebble configuration. Repeated calculations of k eff with MCNP6.1 and ENDF/B-VII.1 are lower than the benchmark values and within 1% (~3σ) except for Cores 5 and 9, which calculate lower than the benchmark eigenvalues within 4σ. The primary difference between the two nuclear data libraries is the adjustment of the absorption cross section of graphite. Simulations of the absorber rod worth measurements are within 3σ of the benchmark experiment values. The complete benchmark evaluation details are available in the 2014 edition of the International Handbook of Evaluated Reactor Physics Benchmark Experiments

Study on lower hybrid current drive efficiency at high density towards long-pulse regimes in Experimental Advanced Superconducting Tokamak

International Nuclear Information System (INIS)

Li, M. H.; Ding, B. J.; Zhang, J. Z.; Gan, K. F.; Wang, H. Q.; Zhang, L.; Wei, W.; Li, Y. C.; Wu, Z. G.; Ma, W. D.; Jia, H.; Chen, M.; Yang, Y.; Feng, J. Q.; Wang, M.; Xu, H. D.; Shan, J. F.; Liu, F. K.; Peysson, Y.

2014-01-01

Significant progress on both L- and H-mode long-pulse discharges has been made recently in Experimental Advanced Superconducting Tokamak (EAST) with lower hybrid current drive (LHCD) [J. Li et al., Nature Phys. 9, 817 (2013) And B. N. Wan et al., Nucl. Fusion 53, 104006 (2013).]. In this paper, LHCD experiments at high density in L-mode plasmas have been investigated in order to explore possible methods of improving current drive (CD) efficiency, thus to extend the operational space in long-pulse and high performance plasma regime. It is observed that the normalized bremsstrahlung emission falls much more steeply than 1/n e-av (line-averaged density) above n e-av  = 2.2 × 10 19  m −3 indicating anomalous loss of CD efficiency. A large broadening of the operating line frequency (f = 2.45 GHz), measured by a radio frequency (RF) probe located outside the EAST vacuum vessel, is generally observed during high density cases, which is found to be one of the physical mechanisms resulting in the unfavorable CD efficiency. Collisional absorption of lower hybrid wave in the scrape off layer (SOL) may be another cause, but this assertion needs more experimental evidence and numerical analysis. It is found that plasmas with strong lithiation can improve CD efficiency largely, which should be benefited from the changes of edge parameters. In addition, several possible methods are proposed to recover good efficiency in future experiments for EAST

Compton current detector

International Nuclear Information System (INIS)

Carvalho Campos, J.S. de.

1984-01-01

The project and construction of a Compton current detector, with cylindrical geometry using teflon as dielectric material; for electromagnetic radiation in range energy between 10 KeV and 2 MeV are described. The measurements of Compton current in teflon were obtained using an electrometer. The Compton current was promoted by photon flux proceeding from X ray sources (MG 150 Muller device) and gamma rays of 60 Co. The theory elaborated to explain the experimental results is shown. The calibration curves for accumulated charge and current in detector in function of exposition rates were obtained. (M.C.K.) [pt

Current-based detection of nonlocal spin transport in graphene for spin-based logic applications

Science.gov (United States)

Wen, Hua; Zhu, Tiancong; Luo, Yunqiu Kelly; Amamou, Walid; Kawakami, Roland K.

2014-05-01

Graphene has been proposed for novel spintronic devices due to its robust and efficient spin transport properties at room temperature. Some of the most promising proposals require current-based readout for integration purposes, but the current-based detection of spin accumulation has not yet been developed. In this work, we demonstrate current-based detection of spin transport in graphene using a modified nonlocal geometry. By adding a variable shunt resistor in parallel to the nonlocal voltmeter, we are able to systematically cross over from the conventional voltage-based detection to current-based detection. As the shunt resistor is reduced, the output current from the spin accumulation increases as the shunt resistance drops below a characteristic value R*. We analyze this behavior using a one-dimensional drift-diffusion model, which accounts well for the observed behavior. These results provide the experimental and theoretical foundation for current-based detection of nonlocal spin transport.

Experimental study of anti-tumor activity of direct current

International Nuclear Information System (INIS)

Ito, Hisao; Hashimoto, Shozo

1989-01-01

The anti-tumor activity of direct current combined with radiation was studied. The experiments were performed with fibrosarcomas (FSA, NFSA) syngenetic to C3H mice. Direct current (0.6mA, 120min) alone was effective to reduce the tumor sizes, but could not cure the tumors. When the direct current therapy (DC therapy) was combined with radiation the DC therapy following radiation was more effective than that before radiation. Using TCD 50 assay, the DC therapy enhanced the effect of a single dose of radiation with the dose-modifying factor of 1.2. However, tumor control rates by the combination therapy were more improved at the smaller doses of radiation than at the larger ones. When the single DC therapy (0.6mA, 120min) was applied immediately after the first radiation of fractionated one the combination therapy still showed the enhanced effect. However, both DC therapy and the radiation therapy were divided in three fractions, and the DC therapy (0.6mA, 40min) was applied after each radiation. Tumor growth retardation by the combination therapy was no different from that by radiation alone. This result suggests that there might be a minimum required dose of coulombs to show the effect of the combination therapy. (author)

Neoclassical MHD equilibria with ohmic current

International Nuclear Information System (INIS)

Tokuda, Shinji; Takeda, Tatsuoki; Okamoto, Masao.

1989-01-01

MHD equilibria of tokamak plasmas with neoclassical current effects (neoclassical conductivity and bootstrap current) were calculated self-consistently. Neoclassical effects on JFT-2M tokamak plasmas, sustained by ohmic currents, were studied. Bootstrap currents flow little for L-mode type equilibria because of low attainable values of poloidal beta, β J . H-mode type equilibria give bootstrap currents of 30% ohmic currents for β J attained by JFT-2M and 100% for β J ≥ 1.5, both of which are sufficient to change the current profiles and the resultant MHD equilibria. Neoclassical conductivity which has roughly half value of the classical Spitzer conductivity brings peaked ohmic current profiles to yield low safety factor at the magnetic axis. Neoclassical conductivity reduces the value of effective Z(Z eff ) which is necessary to give the observed one-turn voltage but it needs impurities accumulating at the center when such peaked current profiles are not observed. (author)

Assessing the value relevance of current mandatory business model disclosures

DEFF Research Database (Denmark)

Schaper, Stefan; Nielsen, Christian; Simoni, Lorenzo

the model developed by Ohlson (1995). Our results show no significant association between BM disclosure and share prices. The main reason behind this finding can be associated with the low level of disclosure (i.e. the low number of value drivers disclosed on average) by companies as part of their BM......Recent regulations have introduced the requirement for large companies to disclose information about their business model (BM) in the annual reports. The objective of these disclosures is to allow external users to understand better how companies create, deliver and capture value. This study aims...... reports. Ad-hoc created disclosure indexes are based on the taxonomy of business model (BM) configurations developed by Taran et al. (2016) as well as complemented by a frame of reference based on the nice BM canvas elements from Osterwalder and Pigneur (2010). After the classification of companies...

Both Parents and Adolescents Project Their Own Values When Perceiving Each Other's Values

Science.gov (United States)

Stattin, Håkan; Kim, Yunhwan

2018-01-01

How parents and adolescents perceive each other's life values is a key to understanding successful value transmission. In the value socializations literature, it has been proposed that parents' values become internalized when children correctly perceive their parents' values and decide to adopt them as their own. In the current study, we propose…

Health values and prospect theory.

Science.gov (United States)

Treadwell, J R; Lenert, L A

1999-01-01

Health values are important components of medical decisions. Experimental data suggest that people value health in complex and dynamic ways. Prospect theory is a descriptive theory of choice that may accurately characterize how people assign values to health states. The authors first provide background on prospect theory and how it can be applied to health values. Next, they review the relevant health research and find mixed support for prospect theory. Last, they discuss implications of prospect theory for cost-effectiveness analysis. The application of prospect theory to health deserves further research because it may help clarify the link between health and values.

Prevention of hepatocellular carcinoma: potential targets, experimental models, and clinical challenges

Science.gov (United States)

Hoshida, Yujin; Fuchs, Bryan C.; Tanabe, Kenneth K.

2013-01-01

Chronic fibrotic liver diseases such as viral hepatitis eventually develop liver cirrhosis, which causes occurrence of hepatocellular carcinoma (HCC). Given the limited therapeutic efficacy in advanced HCC, prevention of HCC development could be an effective strategy for improving patient prognosis. However, there is still no established therapy to meet the goal. Studies have elucidated a wide variety of molecular mechanisms and signaling pathways involved in HCC development. Genetically-engineered or chemically-treated experimental models of cirrhosis and HCC have been developed and shown their potential value in investigating molecular therapeutic targets and diagnostic biomarkers for HCC prevention. In this review, we overview potential targets of prevention and currently available experimental models, and discuss strategies to translate the findings into clinical practice. PMID:22873223

Current neutralization of nanosecond risetime, high-current electron beam

International Nuclear Information System (INIS)

Lidestri, J.P.; Spence, P.W.; Bailey, V.L.; Putnam, S.D.; Fockler, J.; Eichenberger, C.; Champney, P.D.

1991-01-01

This paper reports that the authors have recently investigated methods to achieve current neutralization in fast risetime (<3 ns) electron beams propagating in low-pressure gas. For this investigation, they injected a 3-MV, 30-kA intense beam into a drift cell containing gas pressures from 0.10 to 20 torr. By using a fast net current monitor (100-ps risetime), it was possible to observe beam front gas breakdown phenomena and to optimize the drift cell gas pressure to achieve maximum current neutralization. Experimental observations have shown that by increasing the drift gas pressure (P ∼ 12.5 torr) to decrease the mean time between secondary electron/gas collisions, the beam can propagate with 90% current neutralization for the full beam pulsewidth (16 ns)

Influence of current and temperature on discharge characteristics of electrochemical nickel−cadmium system

Directory of Open Access Journals (Sweden)

Todorović Andreja

2010-01-01

Full Text Available The paper elaborates determination of characteristic values in the discharging process of non-hermetic nickel-cadmium galvanic battery with nominal voltage Un = 60 V and nominal capacity qn = C5 = 190 Ah and its dependence from current and temperature. Study has been performed with the set of experimental metering of voltages, electromotive force, current from discharge time range and electromotive force in steady state regime before and after battery charging. Electromotive force characteristics are obtained by using the Nernst’s equation, while the least square method was used to determine the average values of internal electrical resistivity, power losses and efficiency level. These results were used in the approximate exponential functions to determine the range dependence of the efficiency level from the internal electrical resistance of discharge current in reliance from the temperature range. Obtained results show that, in accordance to the given voltage variation of 10% Un, this type of battery holds maximal full load current of one hour capacity at the temperature of 25°C and maximal full load current of two hours capacity at the temperature of −30°C. The methodology used in the case study covers determination of the electromotive force in time range based on the metered results of values during complete battery fullness and emptiness with prior determination of equilibrium constants of galvanic battery reaction through method suggested by the author of this paper. Further process, using the electromotive force values obtained through the aforementioned process, the metered current, and approximate polynomial function of the nominal discharge voltage characteristic determines range of battery internal electric resistance from time, followed by the selection of discharge cases with average values for: voltage, electromotive force, internal electrical resistance, available and utilized power, power losses, and battery efficiency

Equilibrium of current driven rotating liquid metal

International Nuclear Information System (INIS)

Velikhov, E.P.; Ivanov, A.A.; Zakharov, S.V.; Zakharov, V.S.; Livadny, A.O.; Serebrennikov, K.S.

2006-01-01

In view of great importance of magneto-rotational instability (MRI) as a fundamental mechanism for angular momentum transfer in magnetized stellar accretion disks, several research centers are involved in experimental study of MRI under laboratory conditions. The idea of the experiment is to investigate the rotation dynamics of well conducting liquid (liquid metal) between two cylinders in axial magnetic field. In this Letter, an experimental scheme with immovable cylinders and fluid rotation driven by radial current is considered. The analytical solution of a stationary flow was found taking into account the external current. Results of axially symmetric numerical simulations of current driven fluid dynamics in experimental setup geometry are presented. The analytical solution and numerical simulations show that the current driven fluid rotation in axial magnetic field provides the axially homogeneous velocity profile suitable for MRI study in classical statement

Renormalization of the axial-vector current in QCD

International Nuclear Information System (INIS)

Chiu, C.B.; Pasupathy, J.; Wilson, S.L.

1985-01-01

Following the method of Ioffe and Smilga, the propagation of the baryon current in an external constant axial-vector field is considered. The close similarity of the operator-product expansion with and without an external field is shown to arise from the chiral invariance of gauge interactions in perturbation theory. Several sum rules corresponding to various invariants both for the nucleon and the hyperons are derived. The analysis of the sum rules is carried out by two independent methods, one called the ratio method and the other called the continuum method, paying special attention to the nondiagonal transitions induced by the external field between the ground state and excited states. Up to operators of dimension six, two new external-field-induced vacuum expectation values enter the calculations. Previous work determining these expectation values from PCAC (partial conservation of axial-vector current) are utilized. Our determination from the sum rules of the nucleon axial-vector renormalization constant G/sub A/, as well as the Cabibbo coupling constants in the SU 3 -symmetric limit (m/sub s/ = 0), is in reasonable accord with the experimental values. Uncertainties in the analysis are pointed out. The case of broken flavor SU 3 symmetry is also considered. While in the ratio method, the results are stable for variation of the fiducial interval of the Borel mass parameter over which the left-hand side and the right-hand side of the sum rules are matched, in the continuum method the results are less stable. Another set of sum rules determines the value of the linear combination 7F-5D to be roughly-equal0, or D/(F+D)roughly-equal(7/12). .AE

Electron and ion currents relevant to accurate current integration in MeV ion backscattering spectrometry

International Nuclear Information System (INIS)

Matteson, S.; Nicolet, M.A.

1979-01-01

The magnitude and characteristics of the currents which flow in the target and the chamber of an MeV ion backscattering spectrometer are examined. Measured energy distributions and the magnitude of high-energy secondary electron currents are reported. An empirical universal curve is shown to fit the energy distribution of secondary electrons for several combinations of ion energy, targets and ion species. The magnitude of tertiary electron currents which arise at the vacuum vessel walls is determined for various experimental situations and is shown to be non-negligible in many cases. An experimental arrangement is described which permits charge integrations to 1% arruracy without restricting access to the target as a Faraday cage does. (Auth.)

Current status of antiproton impact ionization of atoms and molecules: theoretical and experimental perspectives

DEFF Research Database (Denmark)

Kirchner, Tom; Knudsen, Helge

2011-01-01

Experimental and theoretical progress in the field of antiproton-impact-induced ionization of atoms and molecules is reviewed. We describe the techniques used to measure ionization cross sections and give an overview of the experimental results supplemented by tables of all existing data. An atte......Experimental and theoretical progress in the field of antiproton-impact-induced ionization of atoms and molecules is reviewed. We describe the techniques used to measure ionization cross sections and give an overview of the experimental results supplemented by tables of all existing data...

Social Value Induction and Cooperation in the Centipede Game.

Directory of Open Access Journals (Sweden)

Briony D Pulford

Full Text Available The Centipede game provides a dynamic model of cooperation and competition in repeated dyadic interactions. Two experiments investigated psychological factors driving cooperation in 20 rounds of a Centipede game with significant monetary incentives and anonymous and random re-pairing of players after every round. The main purpose of the research was to determine whether the pattern of strategic choices observed when no specific social value orientation is experimentally induced--the standard condition in all previous investigations of behavior in the Centipede and most other experimental games--is essentially individualistic, the orthodox game-theoretic assumption being that players are individualistically motivated in the absence of any specific motivational induction. Participants in whom no specific state social value orientation was induced exhibited moderately non-cooperative play that differed significantly from the pattern found when an individualistic orientation was induced. In both experiments, the neutral treatment condition, in which no orientation was induced, elicited competitive behavior resembling behavior in the condition in which a competitive orientation was explicitly induced. Trait social value orientation, measured with a questionnaire, influenced cooperation differently depending on the experimentally induced state social value orientation. Cooperative trait social value orientation was a significant predictor of cooperation and, to a lesser degree, experimentally induced competitive orientation was a significant predictor of non-cooperation. The experimental results imply that the standard assumption of individualistic motivation in experimental games may not be valid, and that the results of such investigations need to take into account the possibility that players are competitively motivated.

Spatial nonuniformity of current flow and its consideration in determination of characteristics of surface illuminated InAsSbP/InAs-based photodiodes

Energy Technology Data Exchange (ETDEWEB)

Zotova, N V; Karandashev, S A; Matveev, B. A., E-mail: Bmat@iropt3.ioffe.ru; Remennyy, M A; Rybal' chenko, A Yu; Stus' , N M [Russian Academy of Sciences, Ioffe Physical Technical Institute (Russian Federation)

2011-04-15

Current-voltage characteristics of surface-irradiated photodiodes based on the InAsSbP/InAs structures are analyzed using experimental data on the distribution of electroluminescence intensity over the diode surface and taking into account thickening the current streamlines near the contacts. The influence of the potential barrier associated with the N-InAsSbP/n-InAs junction in double heterostructures on the differential resistance of diodes under zero bias, the value of the reverse current, and spreading of the forward current is discussed.

Spatial nonuniformity of current flow and its consideration in determination of characteristics of surface illuminated InAsSbP/InAs-based photodiodes

International Nuclear Information System (INIS)

Zotova, N. V.; Karandashev, S. A.; Matveev, B. A.; Remennyy, M. A.; Rybal’chenko, A. Yu.; Stus’, N. M.

2011-01-01

Current-voltage characteristics of surface-irradiated photodiodes based on the InAsSbP/InAs structures are analyzed using experimental data on the distribution of electroluminescence intensity over the diode surface and taking into account thickening the current streamlines near the contacts. The influence of the potential barrier associated with the N-InAsSbP/n-InAs junction in double heterostructures on the differential resistance of diodes under zero bias, the value of the reverse current, and spreading of the forward current is discussed.

Compact high-current, subnanosecond electron accelerator

Energy Technology Data Exchange (ETDEWEB)

Shpak, V G; Shunajlov, S A; Ulmaskulov, M R; Yalandin, M I [Russian Academy of Sciences, Ekaterinburg (Russian Federation). Inst. of Electrophysics; Pegel, I V [Russian Academy of Sciences, Tomsk (Russian Federation). High-Current Electronics Inst.; Tarakanov, V P [Russian Academy of Sciences, Moscow (Russian Federation). High-Temperature Inst.

1997-12-31

A compact subnanosecond, high-current electron accelerator producing an annular electron beam of duration up to 300 - 400 ps, energy about 250 keV, and current up to 1 kA has been developed to study transient processes in pulsed power microwave devices. The measuring and recording techniques used to experimentally investigate the dynamics of the beam current pulse and the transformation of the electron energy during the transportation of the beam in a longitudinal magnetic field are described. The experimental data obtained are compared with the predictions of a numerical simulation. (author). 6 figs., 5 refs.

The value of tax shields with a fixed book-value leverage ratio

OpenAIRE

Fernandez, Pablo

2005-01-01

The value of tax shields depends only on the nature of the stochastic process of the net increases of debt. The value of tax shields in a world with no leverage cost is the tax rate times the current debt plus the present value of the net increases of debt. We develop valuation formulae for a company that maintains a fixed book-value leverage ratio and show that it is more realistic than to assume, as Miles-Ezzell (1980) do, a fixed market-value leverage ratio. We also show that Miles-Ezzell ...

Experimental primates and non-human primate (NHP) models of human diseases in China: current status and progress.

Science.gov (United States)

Zhang, Xiao-Liang; Pang, Wei; Hu, Xin-Tian; Li, Jia-Li; Yao, Yong-Gang; Zheng, Yong-Tang

2014-11-18

Non-human primates (NHPs) are phylogenetically close to humans, with many similarities in terms of physiology, anatomy, immunology, as well as neurology, all of which make them excellent experimental models for biomedical research. Compared with developed countries in America and Europe, China has relatively rich primate resources and has continually aimed to develop NHPs resources. Currently, China is a leading producer and a major supplier of NHPs on the international market. However, there are some deficiencies in feeding and management that have hampered China's growth in NHP research and materials. Nonetheless, China has recently established a number of primate animal models for human diseases and achieved marked scientific progress on infectious diseases, cardiovascular diseases, endocrine diseases, reproductive diseases, neurological diseases, and ophthalmic diseases, etc. Advances in these fields via NHP models will undoubtedly further promote the development of China's life sciences and pharmaceutical industry, and enhance China's position as a leader in NHP research. This review covers the current status of NHPs in China and other areas, highlighting the latest developments in disease models using NHPs, as well as outlining basic problems and proposing effective countermeasures to better utilize NHP resources and further foster NHP research in China.

Electromagnetic torques and forces due to misalignment effects and eddy currents in the homopolar generator, power supply for the Texas Experimental Tokamak (TEXT)

International Nuclear Information System (INIS)

Driga, M.D.; Bird, W.L.; Tolk, K.M.; Weldon, W.F.; Rylander, H.G.; Woodson, H.H.

1977-01-01

Asymmetries in the applied magnetic field due to manufacturing tolerances and rotor-stator misalignments can cause significant forces and moments in a homopolar generator. Parasitic eddy-currents in the rotor, brushes and bearings are also important effects of such asymmetries. The finite element method is used to calculate the magnetic flux distributions in the TEXT homopolar generators. The axial magnetic thrust force and the magnetic tilt moment acting on the rotor are calculated. Eddy-current torques opposing rotor motion are determined using the theory for eddy-current brakes. The results have been used in the design of the TEXT homopolar generator which have been proposed to provide the energy store and conversion for the toroidal field and ohmic heating coils of the new Texas Experimental Tokamak

Current density profile evolution in JET

International Nuclear Information System (INIS)

Stubberfield, P.M.; Balet, B.; Campbell, D.; Challis, C.D.; Cordey, J.G.; O'Rourke, J.; Hammett, G.; Schmidt, G.L.

1989-01-01

Simulation studies have been made of the current density profile evolution in discharges where the bootstrap current is expected to be significant. The changes predicted in the total current profile have been confirmed by comparison with experimental results. (author) 8 refs., 6 figs

Measurement of the beta-asymmetry parameter of Cu-67 in search for tensor-type currents in the weak interaction

OpenAIRE

Soti, Gergely; Breitenfeldt, Martin; Finlay, Paul; Herzog, P; Knecht, Andreas; Koester, U; Kraev, I. S; Porobic, Tomica; Prashanth, P. N; Towner, I. S; Tramm, C; Zakoucky, D; Severijns, Nathal; Wauters, F

2014-01-01

The experimental value, ˜A = 0.587(14), is in agreement with the standard model value of 0.5991(2) and is interpreted in terms of physics beyond the standard model. The limits obtained on possible tensor-type charged currents in the weak interaction Hamiltonian are −0.045 < (C_T + C'_T)/CA < 0.159 (90% C.L.). The obtained limits are comparable to limits from other correlation measurements in nuclear β decay and contribute to further constraining tensor coupling constants.

Review of JT-60U experimental results from March to October, 1991

International Nuclear Information System (INIS)

1992-06-01

Experimental results achieved in the initial operation of JT-60U are described in this paper. Experiments of JT-60U were initiated in March 1991, and deuterium experiments started in the middle of July. Multivariable non-interacting control, H-mode experiments, the high-q and high-β p regime with hot ion enhanced confinement, the divertor heat flux, etc. are reported. Achieved values of the first experiment of the JT-60U LHCD in 1991 were P LH = 1.5 MW, driven current I RF = 2MA, current drive efficiency η CD (=n-bar e R p I RF /P LH ) = 0.25 x 10 20 m -2 A/W and current driven product CDP(=n-bar e R p I RF ) = 3 x 10 20 m -2 MA. (J.P.N.)

A fast transient response low dropout regulator with current control methodology

Energy Technology Data Exchange (ETDEWEB)

Ma Zhuo; Guo Yang; Duan Zhikui; Xie Lunguo; Chen Jihua; Yu Jinshan, E-mail: guoyang@nudt.edu.cn [School of Computer, National University of Defense Technology, Changsha 410073 (China)

2011-08-15

A transient performance optimized CCL-LDO regulator is proposed. In the CCL-LDO, the control method of the charge pump phase-locked loop is adopted. A current control loop has the feedback signal and reference current to be compared, and then a loop filter generates the gate voltage of the power MOSFET by integrating the error current. The CCL-LDO has the optimized damping coefficient and natural resonant frequency, while its output voltage can be sub-1-V and is not restricted by the reference voltage. With a 1 {mu}F decoupling capacitor, the experimental results based on a 0.13 {mu}m CMOS process show that the output voltage is 1.0 V; when the workload changes from 100 {mu}A to 100 mA transiently, the stable dropout is 4.25 mV, the settling time is 8.2 {mu}s and the undershoot is 5.11 mV; when the workload changes from 100 mA to 100 {mu}A transiently, the stable dropout is 4.25 mV, the settling time is 23.3 {mu}s and the overshoot is 6.21 mV. The PSRR value is more than -95 dB. Most of the attributes of the CCL-LDO are improved rapidly with a FOM value of 0.0097.

A fast transient response low dropout regulator with current control methodology

International Nuclear Information System (INIS)

Ma Zhuo; Guo Yang; Duan Zhikui; Xie Lunguo; Chen Jihua; Yu Jinshan

2011-01-01

A transient performance optimized CCL-LDO regulator is proposed. In the CCL-LDO, the control method of the charge pump phase-locked loop is adopted. A current control loop has the feedback signal and reference current to be compared, and then a loop filter generates the gate voltage of the power MOSFET by integrating the error current. The CCL-LDO has the optimized damping coefficient and natural resonant frequency, while its output voltage can be sub-1-V and is not restricted by the reference voltage. With a 1 μF decoupling capacitor, the experimental results based on a 0.13 μm CMOS process show that the output voltage is 1.0 V; when the workload changes from 100 μA to 100 mA transiently, the stable dropout is 4.25 mV, the settling time is 8.2 μs and the undershoot is 5.11 mV; when the workload changes from 100 mA to 100 μA transiently, the stable dropout is 4.25 mV, the settling time is 23.3 μs and the overshoot is 6.21 mV. The PSRR value is more than -95 dB. Most of the attributes of the CCL-LDO are improved rapidly with a FOM value of 0.0097.

Nanosecond electrical explosion of thin aluminum wire in vacuum: experimental and computational investigations

International Nuclear Information System (INIS)

Cochrane, Kyle Robert; Struve, Kenneth William; Rosenthal, Stephen Edgar; McDaniel, Dillon Heirman; Sarkisov, Gennady Sergeevich; Deeney, Christopher

2004-01-01

The experimental and computational investigations of nanosecond electrical explosion of thin Al wire in vacuum are presented. We have demonstrated that increasing the current rate leads to increased energy deposited before voltage collapse. Laser shadowgrams of the overheated Al core exhibit axial stratification with a ∼100 (micro)m period. The experimental evidence for synchronization of the wire expansion and light emission with voltage collapse is presented. Two-wavelength interferometry shows an expanding Al core in a low-ionized gas condition with increasing ionization toward the periphery. Hydrocarbons are indicated in optical spectra and their influence on breakdown physics is discussed. The radial velocity of low-density plasma reaches a value of ∼100 km/s. The possibility of an overcritical phase transition due to high pressure is discussed. 1D MHD simulation shows good agreement with experimental data. MHD simulation demonstrates separation of the exploding wire into a high-density cold core and a low-density hot corona as well as fast rejection of the current from the wire core to the corona during voltage collapse. Important features of the dynamics for wire core and corona follow from the MHD simulation and are discussed.

Neutral currents

International Nuclear Information System (INIS)

Aubert, B.

1994-11-01

The evidence for the existence of weak neutral current has been a very controverted topics in the early 1970's, as well as the muon did in the 1930's. The history is very rich considering the evolution of the experimental techniques in high energy particle physics. The history of the discovery and the study of weak neutral current is reviewed. Later the quest of the intermediate vector boson continues with the decision of the community to build a large proton antiproton collider. (K.A.). 14 refs., 1 fig

Neutrino--proton interactions at Fermilab energies: Experimental arrangement, analysis procedures, and qualitative features of the data

International Nuclear Information System (INIS)

Chapman, J.W.; Coffin, C.T.; Diamond, R.N.; French, H.; Louis, W.; Roe, B.P.; Seidl, A.A.; Vander Velde, J.C.; Berge, J.P.; Bogert, D.; DiBianca, F.A.; Dunaitsev, A.; Efremenko, V.; Ermolov, P.; Fowler, W.; Hanft, R.; Harigel, G.; Huson, F.R.; Kolganov, V.; Mukhin, A.; Nezrick, F.A.; Rjabov, Y.; Scott, W.G.; Smart, W.; Truxton, R.

1976-01-01

The Fermilab 15-ft bubble chamber filled with hydrogen was exposed to a broad-momentum-band horn-focused neutrino beam produced by 300-GeV interacting protons. The selection procedure to choose a charged-current neutrino event sample is discussed. Fewer than three percent of the events are due to neutral hadron interactions. We present and experimentally test a method that can be used to identify the muon, estimate the incident neutrino energy, and eliminate most neutral-current interactions from the charged-current sample. Above 10 GeV the method produces an approximately 86% pure sample of charged-current events with an error in energy estimation of the order of 8% over a broad region of the data. In addition we establish experimentally several important properties of high-energy charged-current neutrino interactions. The hadrons are produced in a jet, the individual particles having sharply limited momenta perpendicular to the hadronic axis. The jet structure is maintained with constant properties to very high values of Q 2 and hadronic mass. The fraction of energy going into invisible particles is moderate, consistent with that expected. The average number of neutral pions rises linearly with the average number of charged particles

Immunosuppression for in vivo research: state-of-the-art protocols and experimental approaches

Institute of Scientific and Technical Information of China (English)

Rita Diehl; Fabienne Ferrara; Claudia Müller; Antje Y Dreyer; Damian D McLeod; Stephan Fricke; Johannes Boltze

2017-01-01

Almost every experimental treatment strategy using non-autologous cell,tissue or organ transplantation is tested in small and large animal models before clinical translation.Because these strategies require immunosuppression in most cases,immunosuppressive protocols are a key element in transplantation experiments.However,standard immunosuppressive protocols are often applied without detailed knowledge regarding their efficacy within the particular experimental setting and in the chosen model species.Optimization of such protocols is pertinent to the translation of experimental results to human patients and thus warrants further investigation.This review summarizes current knowledge regarding immunosuppressive drug classes as well as their dosages and application regimens with consideration of species-specific drug metabolization and side effects.It also summarizes contemporary knowledge of novel immunomodulatory strategies,such as the use of mesenchymal stem cells or antibodies.Thus,this review is intended to serve as a state-of-the-art compendium for researchers to refine applied experimental immunosuppression and immunomodulation strategies to enhance the predictive value of preclinical transplantation studies.

Understanding the value of plant diversity for ecosystem functioning through niche theory

Science.gov (United States)

Isbell, Forest; Purves, Drew W.; Loreau, Michel

2016-01-01

Biodiversity experiments have generated robust empirical results supporting the hypothesis that ecosystems function better when they contain more species. Given that ecosystems provide services that are valued by humans, this inevitably suggests that the loss of species from natural ecosystems could diminish their value. This raises two important questions. First, will experimental results translate into the real world, where species are being lost at an alarming rate? And second, what are the benefits and pitfalls of such valuation exercises? We argue that the empirical results obtained in experiments are entirely consistent with well-established theories of species coexistence. We then examine the current body of work through the lens of niche theory and highlight where closer links with theory could open up opportunities for future research. We argue that niche theory predicts that diversity–functioning relationships are likely to be stronger (and require more species) in the field than in simplified experimental settings. However, we caution that while many of the biological processes that promote coexistence can also generate diversity–function relationships, there is no simple mapping between the two. This implies that valuation exercises need to proceed with care. PMID:27928043

Electric-current-induced step bunching on Si(111)

International Nuclear Information System (INIS)

Homma, Yoshikazu; Aizawa, Noriyuki

2000-01-01

We experimentally investigated step bunching induced by direct current on vicinal Si(111)'1x1' surfaces using scanning electron microscopy and atomic force microscopy. The scaling relation between the average step spacing l b and the number of steps N in a bunch, l b ∼N -α , was determined for four step-bunching temperature regimes above the 7x7-'1x1' transition temperature. The step-bunching rate and scaling exponent differ between neighboring step-bunching regimes. The exponent α is 0.7 for the two regimes where the step-down current induces step bunching (860-960 and 1210-1300 deg. C), and 0.6 for the two regimes where the step-up current induces step bunching (1060-1190 and >1320 deg. C). The number of single steps on terraces also differs in each of the four temperature regimes. For temperatures higher than 1280 deg. C, the prefactor of the scaling relation increases, indicating an increase in step-step repulsion. The scaling exponents obtained agree reasonably well with those predicted by theoretical models. However, they give unrealistic values for the effective charges of adatoms for step-up-current-induced step bunching when the 'transparent' step model is used

THE CURRENT STATE OF KNOWLEDGE IN THE VALUE RELEVANCE RESEARCH FIELD

Directory of Open Access Journals (Sweden)

Carmen- Alexandra BALTARIU

2015-04-01

Full Text Available The purpose of this paper is to assess the scientific literature referring to the value relevance of reported accounting information over a twelve year period starting from 2002. The approach of the paper is a theoretical (conceptual one. In order to complete the purpose of the paper we selected as research method the longitudinal qualitative analysis. The qualitative analysis carried out presents a deductive character. Our conclusions regarding the general characteristics of the research field pertaining to the value relevance of reported accounting information are drawn based on the main results and scientific contributions identified in the research field of interest.

Analysis of DCA experimental data

International Nuclear Information System (INIS)

Min, B. J.; Kim, S. Y.; Ryu, S. J.; Seok, H. C.

2000-01-01

The lattice characteristics of DCA are calculated with WIMS-ATR code to validate WIMS-AECL code for the lattice analysis of CANDU core by using experimental data of DCA at JNC. Analytical studies of some critical experiments had been performed to analyze the effects of fuel composition. Different items of reactor physics such as local power peaking factor (LPF), effective multiplication factor (Keff) and coolant void reactivity were calculated for two coolant void fractions (0% and 100%). LPFs calculated by WIMS-ATR code are in close agreement with the experimental results. LPFs calculated by WIMS-AECL code with WINFRITH and ENDF/B-V libraries have similar values for both libraries but the differences between experimental data and calculated results by WIMS-AECL code are larger than those of WIMS-ATR code. The maximum difference between the values calculated by WIMS-ATR and experimental values of LPFs are within 1.3%. The coupled code systems WIMS-ATR and CITATION used in this analysis predict Keff within 1% ΔK and coolant void reactivity within 4 % ΔK/K in all cases. The coolant void reactivity of uranium fuel is found to be positive. To validate WIMS-AECL code, the core characteristics of DCA shall be calculated by WIMS-AECL and CITATION codes in the future

An innovative experimental sequence on electromagnetic induction and eddy currents based on video analysis and cheap data acquisition

International Nuclear Information System (INIS)

Bonanno, A; Sapia, P; Bozzo, G

2017-01-01

In this work, we present a coherent sequence of experiments on electromagnetic (EM) induction and eddy currents, appropriate for university undergraduate students, based on a magnet falling through a drilled aluminum disk. The sequence, leveraging on the didactical interplay between the EM and mechanical aspects of the experiments, allows us to exploit the students’ awareness of mechanics to elicit their comprehension of EM phenomena. The proposed experiments feature two kinds of measurements: (i) kinematic measurements (performed by means of high-speed video analysis) give information on the system’s kinematics and, via appropriate numerical data processing, allow us to get dynamic information, in particular on energy dissipation; (ii) induced electromagnetic field (EMF) measurements (by using a homemade multi-coil sensor connected to a cheap data acquisition system) allow us to quantitatively determine the inductive effects of the moving magnet on its neighborhood. The comparison between experimental results and the predictions from an appropriate theoretical model (of the dissipative coupling between the moving magnet and the conducting disk) offers many educational hints on relevant topics related to EM induction, such as Maxwell’s displacement current, magnetic field flux variation, and the conceptual link between induced EMF and induced currents. Moreover, the didactical activity gives students the opportunity to be trained in video analysis, data acquisition and numerical data processing. (paper)

Experimental investigation of the check valve behaviour when the flow is reversing

Directory of Open Access Journals (Sweden)

Himr D.

2017-01-01

Full Text Available Check valve in a pipeline is supposed to prevent the reverse flow and to allow the flow in the positive direction. The construction of check valves follows these requirements, but the check valve must not cause pressure pulsations in transients. It means when the fluid is accelerating or decelerating. The article describes an experimental investigation of a swing check valve when the flow is changing its direction. The check valve was placed in an experimental circuit, where the pressure on the upstream and downstream side of the valve was measured and the current value of flow rate was determined. The goal was to simulate conditions in the real system, where the check valve slam had been observed.

Differences in spirometry values between U.S. children 6-11 years and adolescents 12-19 years with current asthma, 2007-2010.

Science.gov (United States)

Kit, Brian K; Simon, Alan E; Tilert, Timothy; Okelo, Sande; Akinbami, Lara J

2016-03-01

National Asthma Education and Prevention Program (NAEPP) guidelines recommend that periodic spirometry be performed in youth with asthma. NAEPP uses different spirometry criteria to define uncontrolled asthma for children (6-11 years) and adolescents (12+ years). To describe differences in spirometry between U.S. children and adolescents with current asthma. We examined cross-sectional spirometry data from 453 U.S. youth with current asthma age 6-19 years from the 2007-2010 National Health and Nutrition Examination Surveys. The main outcomes were percentage predicted forced expiratory volume at 1 sec (FEV1%) ≤80 and the ratio of FEV1 to forced vital capacity (FEV1/FVC) ≤0.80. We also examined the prevalence of youth with spirometry values consistent with uncontrolled asthma, using NAEPP age-specific criteria, defined for children aged 6-11 years as FEV1% ≤80 or FEV1/FVC ≤0.80, and for adolescents aged 12-19 years as FEV1% ≤80. Children 6-11 years and adolescents 12-19 years did not differ in prevalence of FEV1% ≤80 (10.1% vs. 9.0%) or FEV1/FVC ≤0.80 (30.6% vs. 29.8%). However, based on the NAEPP age-specific criteria, 33.0% of children 6-11 years and 9.0% of adolescents 12-19 years had spirometry values consistent with uncontrolled asthma (P spirometry values consistent with uncontrolled asthma did differ. The difference appears to stem mainly from the different spirometry criteria for the two age groups. © 2015 Wiley Periodicals, Inc.

Plasma-current structures of plasma focus during the current disruption

International Nuclear Information System (INIS)

Krokhin, O.N.; Kalachev, N.V.; Malafeev, Yu.S.; Nikulin, V.Ya; Polukhin, S.N.; Tsybenko, S.P.

2000-01-01

The results are presented of an investigation of the plasma structures arising during the current disruption in the Dense Plasma Focus (DPF). The study was performed using the laser-shadow and interferometry methods together with measurements of current and X-ray radiation. An analysis of the experimental results shows that for the construction of a multi mega-amperes current disruption device, the Filippov type of DPF (in comparison with the Mather type) is to be preferred since the processes occurring in the X-ray regime are much faster than in the pinch regime, and this type of plasma focus is geometrically more suitable for the assembly of such a current disrupter.This disrupter is now under construction, based on the 'Tulip' DPF installation

The problem with value

Science.gov (United States)

O’Doherty, John P.

2015-01-01

Neural correlates of value have been extensively reported in a diverse set of brain regions. However, in many cases it is difficult to determine whether a particular neural response pattern corresponds to a value-signal per se as opposed to an array of alternative non-value related processes, such as outcome-identity coding, informational coding, encoding of autonomic and skeletomotor consequences, alongside previously described “salience” or “attentional” effects. Here, I review a number of experimental manipulations that can be used to test for value, and I identify the challenges in ascertaining whether a particular neural response is or is not a value signal. Finally, I emphasize that some non-value related signals may be especially informative as a means of providing insight into the nature of the decision-making related computations that are being implemented in a particular brain region. PMID:24726573

Ground Return Current Behaviour in High Voltage Alternating Current Insulated Cables

Directory of Open Access Journals (Sweden)

Roberto Benato

2014-12-01

Full Text Available The knowledge of ground return current in fault occurrence plays a key role in the dimensioning of the earthing grid of substations and of cable sealing end compounds, in the computation of rise of earth potential at substation sites and in electromagnetic interference (EMI on neighbouring parallel metallic conductors (pipes, handrails, etc.. Moreover, the ground return current evaluation is also important in steady-state regime since this stray current can be responsible for EMI and also for alternating current (AC corrosion. In fault situations and under some assumptions, the ground return current value at a substation site can be computed by means of k-factors. The paper shows that these simplified and approximated approaches have a lot of limitations and only multiconductor analysis can show the ground return current behaviour along the cable (not only the two end values both in steady-state regime and in short circuit occurrence (e.g., phase-to-ground and phase-to-phase-to-ground. Multiconductor cell analysis (MCA considers the cable system in its real asymmetry without simplified and approximated hypotheses. The sensitivity of ground return current on circuit parameters (cross-bonding box resistances, substation earthing resistances, soil resistivity is presented in the paper.

Experimental Protocol to Determine the Chloride Threshold Value for Corrosion in Samples Taken from Reinforced Concrete Structures.

Science.gov (United States)

Angst, Ueli M; Boschmann, Carolina; Wagner, Matthias; Elsener, Bernhard

2017-08-31

The aging of reinforced concrete infrastructure in developed countries imposes an urgent need for methods to reliably assess the condition of these structures. Corrosion of the embedded reinforcing steel is the most frequent cause for degradation. While it is well known that the ability of a structure to withstand corrosion depends strongly on factors such as the materials used or the age, it is common practice to rely on threshold values stipulated in standards or textbooks. These threshold values for corrosion initiation (Ccrit) are independent of the actual properties of a certain structure, which clearly limits the accuracy of condition assessments and service life predictions. The practice of using tabulated values can be traced to the lack of reliable methods to determine Ccrit on-site and in the laboratory. Here, an experimental protocol to determine Ccrit for individual engineering structures or structural members is presented. A number of reinforced concrete samples are taken from structures and laboratory corrosion testing is performed. The main advantage of this method is that it ensures real conditions concerning parameters that are well known to greatly influence Ccrit, such as the steel-concrete interface, which cannot be representatively mimicked in laboratory-produced samples. At the same time, the accelerated corrosion test in the laboratory permits the reliable determination of Ccrit prior to corrosion initiation on the tested structure; this is a major advantage over all common condition assessment methods that only permit estimating the conditions for corrosion after initiation, i.e., when the structure is already damaged. The protocol yields the statistical distribution of Ccrit for the tested structure. This serves as a basis for probabilistic prediction models for the remaining time to corrosion, which is needed for maintenance planning. This method can potentially be used in material testing of civil infrastructures, similar to established

A robust predictive current controller for healthy and open-circuit faulty conditions of five-phase BLDC drives applicable for wind generators and electric vehicles

International Nuclear Information System (INIS)

Salehi Arashloo, Ramin; Salehifar, Mehdi; Romeral, Luis; Sala, Vicent

2015-01-01

Highlights: • Model predictive deadbeat control of generator stator phase currents. • Fault tolerant control of five-phase BLDC generator. • Control of stator phase currents under normal and open-circuit faulty conditions. • MATLAB simulation and experimental verification of proposed control method. • Verification of robustness and fast respond of proposed controlling method. - Abstract: Fault tolerant control of five-phase brushless direct current (BLDC) machines is gaining more importance in high-safety applications such as offshore wind generators and automotive industries. In many applications, traditional controllers (such as PI controllers) are used to control the stator currents under faulty conditions. These controllers have good performance with dc signals. However, in the case of missing one or two of the phases, appropriate reference currents of these machines have oscillatory dynamics both in phase- and synchronous-reference frames. Non-constant nature of these reference values requires the implication of fast current controllers. In this paper, model predictive deadbeat controllers are proposed to control the stator currents of five-phase BLDC machines under normal and faulty conditions. Open circuit fault is considered for both one and two stator phases, and the behaviour of proposed controlling method is evaluated. This evaluation is generally focused on first, sensitivity of proposed controlling method and second, its speed in following reference current values under transient states. Proposed method is simulated and is verified experimentally on a five-phase BLDC drive

Coastal tomographic mapping of nonlinear tidal currents and residual currents

Science.gov (United States)

Zhu, Ze-Nan; Zhu, Xiao-Hua; Guo, Xinyu

2017-07-01

Depth-averaged current data, which were obtained by coastal acoustic tomography (CAT) July 12-13, 2009 in Zhitouyang Bay on the western side of the East China Sea, are used to estimate the semidiurnal tidal current (M2) as well as its first two overtide currents (M4 and M6). Spatial mean amplitude ratios M2:M4:M6 in the bay are 1.00:0.15:0.11. The shallow-water equations are used to analyze the generation mechanisms of M4 and M6. In the deep area, where water depths are larger than 60 m, M4 velocity amplitudes measured by CAT agree well with those predicted by the advection terms in the shallow water equations, indicating that M4 in the deep area is predominantly generated by the advection terms. M6 measured by CAT and M6 predicted by the nonlinear quadratic bottom friction terms agree well in the area where water depths are less than 20 m, indicating that friction mechanisms are predominant for generating M6 in the shallow area. In addition, dynamic analysis of the residual currents using the tidally averaged momentum equation shows that spatial mean values of the horizontal pressure gradient due to residual sea level and of the advection of residual currents together contribute about 75% of the spatial mean values of the advection by the tidal currents, indicating that residual currents in this bay are induced mainly by the nonlinear effects of tidal currents. This is the first ever nonlinear tidal current study by CAT.

An accurate density functional theory based estimation of pK(a) values of polar residues combined with experimental data: from amino acids to minimal proteins.

Science.gov (United States)

Matsui, Toru; Baba, Takeshi; Kamiya, Katsumasa; Shigeta, Yasuteru

2012-03-28

We report a scheme for estimating the acid dissociation constant (pK(a)) based on quantum-chemical calculations combined with a polarizable continuum model, where a parameter is determined for small reference molecules. We calculated the pK(a) values of variously sized molecules ranging from an amino acid to a protein consisting of 300 atoms. This scheme enabled us to derive a semiquantitative pK(a) value of specific chemical groups and discuss the influence of the surroundings on the pK(a) values. As applications, we have derived the pK(a) value of the side chain of an amino acid and almost reproduced the experimental value. By using our computing schemes, we showed the influence of hydrogen bonds on the pK(a) values in the case of tripeptides, which decreases the pK(a) value by 3.0 units for serine in comparison with those of the corresponding monopeptides. Finally, with some assumptions, we derived the pK(a) values of tyrosines and serines in chignolin and a tryptophan cage. We obtained quite different pK(a) values of adjacent serines in the tryptophan cage; the pK(a) value of the OH group of Ser13 exposed to bulk water is 14.69, whereas that of Ser14 not exposed to bulk water is 20.80 because of the internal hydrogen bonds.

Experimental status of quantum electrodynamics

International Nuclear Information System (INIS)

Drell, S.D.

1980-01-01

The speech of Drell S. on the symposium dedicated to 60th anniversary of Schwinger J. is presented. The fundamental status of the hero of the day in quantum field theory, which turned into quantum electrodynamics, are stated. The theory has been perfectly experimentally confirmed and now is the main model permitting to explain weak and strong interactions. The attention is paid on the difference between theoretical and experimental values of the electron anomalous magnetic moment (asub(e)) obtained in the sixth order of perturbation theory. It is necessary to carry out calculations in the octic order of the perturbation theory in order to obtain more precise value of asub(e). The theory and the experimental difference is demonstrated on the example of estimation of fine and hyperfine structure of hydrogen, muonium, and positronium

Modeling and application of plasma charge current in deep penetration laser welding

International Nuclear Information System (INIS)

Zhang, Xudong; Chen, Wuzhu; Jiang, Ping; Guo, Jing; Tian, Zhiling

2003-01-01

Plasma charge current distribution during deep penetration CO 2 laser welding was analyzed theoretically and experimentally. The laser-induced plasma above the workpiece surface expands up to the nozzle, driven by the particle concentration gradient, forming an electric potential between the workpiece and the nozzle due to the large difference between the diffusion velocities of the ions and the electrons. The plasma-induced current obtained by electrically connecting the nozzle and the workpiece can be increased by adding a negative external voltage. For a fixed set of welding conditions, the plasma charge current increases with the external voltage to a saturation value. The plasma charge current decreases as the nozzle-to-workpiece distance increases. Therefore, closed-loop control of the nozzle-to-workpiece distance for laser welding can be based on the linear relationship between the plasma charge current and the distance. In addition, the amount of plasma above the keyhole can be reduced by a transverse magnetic field, which reduces the attenuation of the incident laser power by the plasma so as to increase the laser welding thermal efficiency

Human experimental pain models: A review of standardized methods in drug development

Directory of Open Access Journals (Sweden)

K. Sunil kumar Reddy

2012-01-01

Full Text Available Human experimental pain models are essential in understanding the pain mechanisms and appear to be ideally suited to test analgesic compounds. The challenge that confronts both the clinician and the scientist is to match specific treatments to different pain-generating mechanisms and hence reach a pain treatment tailored to each individual patient. Experimental pain models offer the possibility to explore the pain system under controlled settings. Standardized stimuli of different modalities (i.e., mechanical, thermal, electrical, or chemical can be applied to the skin, muscles, and viscera for a differentiated and comprehensive assessment of various pain pathways and mechanisms. Using a multimodel-multistructure testing, the nociception arising from different body structures can be explored and modulation of specific biomarkers by new and existing analgesic drugs can be profiled. The value of human experimental pain models is to link animal and clinical pain studies, providing new possibilities for designing successful clinical trials. Spontaneous pain, the main compliant of the neuropathic patients, but currently there is no human model available that would mimic chronic pain. Therefore, current human pain models cannot replace patient studies for studying efficacy of analgesic compounds, although being helpful for proof-of-concept studies and dose finding.

Numerical and experimental analysis of eddy currents induced in tokamak machines

International Nuclear Information System (INIS)

Takahashi, T.; Takahashi, G.; Kazawa, Y.; Suzuki, Y.

1977-01-01

This paper deals with eddy current phenomena in Tokamak machines. A numerical method is presented which will permit eddy currents to be calculated. Examples of numerical results and a discussion of the JT-60 are shown. Calculations are checked by measurements in basic models

Wall conditioning for ITER: Current experimental and modeling activities

Energy Technology Data Exchange (ETDEWEB)

Douai, D., E-mail: david.douai@cea.fr [CEA, IRFM, Association Euratom-CEA, 13108 St. Paul lez Durance (France); Kogut, D. [CEA, IRFM, Association Euratom-CEA, 13108 St. Paul lez Durance (France); Wauters, T. [LPP-ERM/KMS, Association Belgian State, 1000 Brussels (Belgium); Brezinsek, S. [FZJ, Institut für Energie- und Klimaforschung Plasmaphysik, 52441 Jülich (Germany); Hagelaar, G.J.M. [Laboratoire Plasma et Conversion d’Energie, UMR5213, Toulouse (France); Hong, S.H. [National Fusion Research Institute, Daejeon 305-806 (Korea, Republic of); Lomas, P.J. [CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Lyssoivan, A. [LPP-ERM/KMS, Association Belgian State, 1000 Brussels (Belgium); Nunes, I. [Associação EURATOM-IST, Instituto de Plasmas e Fusão Nuclear, 1049-001 Lisboa (Portugal); Pitts, R.A. [ITER International Organization, F-13067 St. Paul lez Durance (France); Rohde, V. [Max-Planck-Institut für Plasmaphysik, 85748 Garching (Germany); Vries, P.C. de [ITER International Organization, F-13067 St. Paul lez Durance (France)

2015-08-15

Wall conditioning will be required in ITER to control fuel and impurity recycling, as well as tritium (T) inventory. Analysis of conditioning cycle on the JET, with its ITER-Like Wall is presented, evidencing reduced need for wall cleaning in ITER compared to JET–CFC. Using a novel 2D multi-fluid model, current density during Glow Discharge Conditioning (GDC) on the in-vessel plasma-facing components (PFC) of ITER is predicted to approach the simple expectation of total anode current divided by wall surface area. Baking of the divertor to 350 °C should desorb the majority of the co-deposited T. ITER foresees the use of low temperature plasma based techniques compatible with the permanent toroidal magnetic field, such as Ion (ICWC) or Electron Cyclotron Wall Conditioning (ECWC), for tritium removal between ITER plasma pulses. Extrapolation of JET ICWC results to ITER indicates removal comparable to estimated T-retention in nominal ITER D:T shots, whereas GDC may be unattractive for that purpose.

Diode-Assisted Buck-Boost Current Source Inverters

DEFF Research Database (Denmark)

Gao, F.; Cai, Liang; Loh, P.C.

2007-01-01

This paper presents a couple of novel current source inverters (CSIs) with the enhanced current buckboost capability. With the unique diode-inductor network added between current source inverter circuitry and current boost elements, the proposed buck-boost current source inverters demonstrate...... uninfluenced. Lastly, all theoretical findings were verified experimentally using constructed laboratory prototypes....

Inhibition of the cardiac inward rectifier potassium currents by KB-R7943.

Science.gov (United States)

Abramochkin, Denis V; Alekseeva, Eugenia I; Vornanen, Matti

2013-09-01

KB-R7943 (2-[2-[4-(4-nitrobenzyloxy)phenyl]ethyl]isothiourea) was developed as a specific inhibitor of the sarcolemmal sodium-calcium exchanger (NCX) with potential experimental and therapeutic use. However, KB-R7943 is shown to be a potent blocker of several ion currents including inward and delayed rectifier K(+) currents of cardiomyocytes. To further characterize KB-R7943 as a blocker of the cardiac inward rectifiers we compared KB-R7943 sensitivity of the background inward rectifier (IK1) and the carbacholine-induced inward rectifier (IKACh) currents in mammalian (Rattus norvegicus; rat) and fish (Carassius carassius; crucian carp) cardiac myocytes. The basal IK1 of ventricular myocytes was blocked with apparent IC50-values of 4.6×10(-6) M and 3.5×10(-6) M for rat and fish, respectively. IKACh was almost an order of magnitude more sensitive to KB-R7943 than IK1 with IC50-values of 6.2×10(-7) M for rat and 2.5×10(-7) M for fish. The fish cardiac NCX current was half-maximally blocked at the concentration of 1.9-3×10(-6) M in both forward and reversed mode of operation. Thus, the sensitivity of three cardiac currents to KB-R7943 block increases in the order IK1~INCXrectifier potassium currents, in particular IKACh, should be taken into account when interpreting the data with this inhibitor from in vivo and in vitro experiments in both mammalian and fish models. © 2013.

Experimental and Numerical Study of FRP Encased Composite Concrete Columns

Directory of Open Access Journals (Sweden)

Mohsen Ishaghian

2017-02-01

Full Text Available A new type of composite column is presented and assessed through experimental testing and numerical modeling. The objective of this research is to investigate design options for a composite column without the use of ferrous materials. This is to avoid the current problem of deterioration of concrete due to expansion of rusting reinforcement members. Such a target can be achieved by replacing the steel reinforcement of concrete columns with pultruded I-shape glass FRP structural sections. The composite column utilizes a glass FRP tube that surrounds a pultruded I-section glass FRP, which is subsequently filled with concrete. The GFRP tube acts as a stay-in-place form in addition to providing confinement to the concrete. A total of four composite columns were tested under monotonic axial loading. The experimental ultimate capacity of each of the tested composite column was compared to the predicted numerical capacity using ANSYS program. The comparison showed that the predicted numerical values were in good agreement with the experimental ones.

Stator Current Harmonic Reduction in a Novel Half Quasi-Z-Source Wind Power Generation System

Directory of Open Access Journals (Sweden)

Shoudao Huang

2016-09-01

Full Text Available The generator stator current gets distorted with unacceptable levels of total harmonic distortion (THD because impedance-source wind power generation systems use three-phase diode rectifiers. The stator current harmonics will cause increasing losses and torque ripple, which reduce the efficiency and stability of the system. This paper proposes a novel half quasi-Z-source inverter (H-qZSI for grid-connected wind power generation systems, which can reduce the generator stator current harmonics a great deal. When H-qZSI operates in the shoot-through zero state, the derivative of the generator stator current is only determined by the instantaneous value of the generator stator voltage, so the nonlinear relationship between generator stator current and stator voltage is improved compared with the traditional impedance-source inverter. Theoretically, it is indicated that the stator current harmonics can be reduced effectively by means of the proposed H-qZSI. Finally, simulation and experimental results are given to verify the theoretical analysis.

EBTS: DESIGN AND EXPERIMENTAL STUDY

International Nuclear Information System (INIS)

PIKIN, A.; ALESSI, J.; BEEBE, E.; KPONOU, A.; PRELEC, K.; KUZNETSOV, G.; TIUNOV, M.

2000-01-01

Experimental study of the BNL Electron Beam Test Stand (EBTS), which is a prototype of the Relativistic Heavy Ion Collider (RHIC) Electron Beam Ion Source (EBIS), is currently underway. The basic physics and engineering aspects of a high current EBIS implemented in EBTS are outlined and construction of its main systems is presented. Efficient transmission of a 10 A electron beam through the ion trap has been achieved. Experimental results on generation of multiply charged ions with both continuous gas and external ion injection confirm stable operation of the ion trap

Review of JT-60U experimental results from January to October, 1992

International Nuclear Information System (INIS)

1993-03-01

Heating experiments have been carried out in JT-60U with plasma current up to 4 MA, toroidal field up to 4.2 T and neutral beam heating power of 30 MW. H-mode was observed at high toroidal field of 4.2 T. Confinement improvement factor of up to 1.6 over the L-mode scaling has been obtained during continuous ELMy phase at 4.2 T, 2.7 MA and an injection power of 25 MW. Confinement enhancement of 2.2 has been obtained. At plasma current of 3.5 MA, diamagnetic stored energy of 7.7 MJ and energy confinement time of 0.36 s have been obtained. In the discharges with high poloidal beta exhibit, high ion temperatures of 38 keV, electron temperatures of 12 keV, maximum diamagnetic stored energy of 6.1 MJ and neutron yield of 2.8 x 10 16 s -1 were obtained. Schemes to avoid locked modes and disruptions have been checked experimentally. Divertor measurement indicates that high q, high density operation is favorable for divertor heat handling. Quantitative analysis of divertor spectroscopy data indicates that the carbon production rate at the divertor plate is explained by deuterium, oxygen and carbon sputtering. Toroidal ripple loss power of NB-injected fast ions to the first wall was investigated by using an infrared TV camera. Absolute values of the ripple loss power and dependence on plasma parameters were consistent with values calculated by an orbit following Monte-Carlo code. In the LHCD area, the linear dispersion relation and accessibility condition for LH wave were experimentally validated. Furthermore, the power directly lost via high energy electron was shown to scale as the slowing down time. Current drive of 400 kA was realized with tangential NB. ICRF experiments using two new antennas started. Sawtooth stabilization at a high n-bar e /P tot value was achieved. (J.P.N.)

Charged weak currents

International Nuclear Information System (INIS)

Turlay, R.

1979-01-01

In this review of charged weak currents I shall concentrate on inclusive high energy neutrino physics. There are surely still things to learn from the low energy weak interaction but I will not discuss it here. Furthermore B. Tallini will discuss the hadronic final state of neutrino interactions. Since the Tokyo conference a few experimental results have appeared on charged current interaction, I will present them and will also comment on important topics which have been published during the last past year. (orig.)

Exchange currents in nuclear physics

International Nuclear Information System (INIS)

Truglik, Eh.

1980-01-01

Starting from Adler's low-energy theorem for the soft pion production amplitudes the predictions of the meson exchange currents theory for the nuclear physics are discussed. The results are reformulated in terms of phenomenological lagrangians. This method allows one to pass naturally to the more realistic case of hard mesons. The predictions are critically compared with the existing experimental data. The main processes in which vector isovector exchange currents, vector isoscalar exchange currents and axial exchange currents take place are pointed out

Parameter and state estimation of experimental chaotic systems using synchronization

Science.gov (United States)

Quinn, John C.; Bryant, Paul H.; Creveling, Daniel R.; Klein, Sallee R.; Abarbanel, Henry D. I.

2009-07-01

We examine the use of synchronization as a mechanism for extracting parameter and state information from experimental systems. We focus on important aspects of this problem that have received little attention previously and we explore them using experiments and simulations with the chaotic Colpitts oscillator as an example system. We explore the impact of model imperfection on the ability to extract valid information from an experimental system. We compare two optimization methods: an initial value method and a constrained method. Each of these involves coupling the model equations to the experimental data in order to regularize the chaotic motions on the synchronization manifold. We explore both time-dependent and time-independent coupling and discuss the use of periodic impulse coupling. We also examine both optimized and fixed (or manually adjusted) coupling. For the case of an optimized time-dependent coupling function u(t) we find a robust structure which includes sharp peaks and intervals where it is zero. This structure shows a strong correlation with the location in phase space and appears to depend on noise, imperfections of the model, and the Lyapunov direction vectors. For time-independent coupling we find the counterintuitive result that often the optimal rms error in fitting the model to the data initially increases with coupling strength. Comparison of this result with that obtained using simulated data may provide one measure of model imperfection. The constrained method with time-dependent coupling appears to have benefits in synchronizing long data sets with minimal impact, while the initial value method with time-independent coupling tends to be substantially faster, more flexible, and easier to use. We also describe a method of coupling which is useful for sparse experimental data sets. Our use of the Colpitts oscillator allows us to explore in detail the case of a system with one positive Lyapunov exponent. The methods we explored are easily

Comparison of standardized uptake values measured on 18F-NaF PET/CT scans using three different tube current intensities

OpenAIRE

Agnes Araujo Valadares; Paulo Schiavom Duarte; Eduardo Bechtloff Woellner; George Barberio Coura-Filho; Marcelo Tatit Sapienza; Carlos Alberto Buchpiguel

2015-01-01

Objective: To analyze standardized uptake values (SUVs) using three different tube current intensities for attenuation correction on 18FNaF PET/CT scans. Materials and Methods: A total of 254 18F-NaF PET/CT studies were analyzed using 10, 20 and 30 mAs. The SUVs were calculated in volumes of interest (VOIs) drawn on three skeletal regions, namely, right proximal humeral diaphysis (RH), right proximal femoral diaphysis (RF), and first lumbar vertebra (LV1) in a total of 712 VOIs. The analyses ...

Lower hybrid current drive in tokamak plasmas

International Nuclear Information System (INIS)

Ushigusa, Kenkichi

1999-03-01

Past ten years progress on Lower Hybrid Current Drive (LHCD) experiments have demonstrated the largest non-inductive current (3.6 MA, JT-60U), the longest current sustainment (2 hours, TRIAM-1M), non-inductive current drive at the highest density (n-bar e - 10 20 m -3 , ALCATOR-C) and the highest current drive efficiency (η CD = 3.5x10 19 m -2 A/W, JT-60). These results indicate that LHCD is one of the most promising methods to drive non-inductive current in the present tokamak plasmas. This paper presents recent experimental results on LHCD experiments. Basic theories of LH waves, the wave propagation and the current drive are briefly summarized. The main part of this paper describes several important results and their physical pictures on recent LHCD experiments; 1) the experimental set-up, 2) the current drive efficiency, 3) the control of current profile and MHD activities, 4) the global energy confinement, 5) the global power flow, 6) fast electron behavior, 7) interaction between LH waves and thermal/fast ions, 8) combination with other CD method. (author)

Estimation of post disruption plasma temperature for fast current quench Aditya plasma shots

International Nuclear Information System (INIS)

Purohit, S.; Chowdhuri, M.B.; Joisa, Y.S.; Raval, J.V.; Ghosh, J.; Jha, R.

2013-01-01

Characteristics of tokamak current quenches are an important issue for the determination of electromagnetic forces that act on the in-vessel components and vacuum vessel during major disruptions. It is observed that thermal quench is followed by a sharp current decay. Fast current quench disruptive plasma shots were investigated for ADITYA tokamak. The current decay time was determined for the selected shots, which were in the range of 0.8 msec to 2.5 msec. This current decay information was then applied to L/R model, frequently employed for the estimation of the current decay time in tokamak plasmas, considering plasma inductance and plasma resistivity. This methodology was adopted for the estimation of the post disruption plasma temperature using the experimentally observed current decay time for the fast current quench disruptive ADITYA plasma shots. The study reveals that for the identified shots there is a constant increase in the current decay time with the post disruption plasma temperature. The investigations also explore the behavior post disruption plasma temperature and the current decay time as a function of the edge safety factor, Q. Post disruption plasma temperature and the current decay time exhibits a decrease with the increase in the value Q. (author)

Investigation of the resistive transition of MgB2 thin film through current noise

International Nuclear Information System (INIS)

Gandini, C; Rajteri, M; Portesi, C; Monticone, E; Masoero, A; Mazzetti, P

2006-01-01

In this paper we present measurements concerning the current noise produced during the resistive transition in a MgB 2 polycrystalline thin film. The power spectrum of the current noise, observed when the temperature is slowly changed across its critical value, presents a large electrical noise of the 1/f n type (n ≅ 3) over a quite wide range of frequencies. This noise may be considered as generated by the abrupt creation of resistive strips across the specimen constituted by grains which have undergone the resistive transition. A computer model that takes into account fluctations of the grain critical currents and of the number of grain per strips, has been developed to simulate the resistive transition and to evaluate the noise power spectrum. When the temperature is incresed and reaches its critical value, resistive strips are formed according to a percolative process, giving rise to resistance steps which are at the origin of the noise. The theoretical results obtained by this model are in good agreement, concerning both the shape and intensity of the noise power spectrum, with the experimental data directly measured on the specimen

X-ray tube current control

International Nuclear Information System (INIS)

Dupuis, W.A.; Resnick, T.A.

1982-01-01

A closed loop feedback system for controlling the current output of an x-ray tube. The system has circuitry for improving the transient response and stability of the x-ray tube current over a substantial nonlinear portion of the tube current production characteristic. The system includes a reference generator for applying adjustable step function reference signals representing desired tube currents. The system also includes means for instantaneous sensing of actual tube current. An error detector compares the value of actual and reference tube current and produces an error signal as a function of their difference. The system feedback loop includes amplification circuitry for controlling x-ray tube filament dc voltage to regulate tube current as a function of the error signal value. The system also includes compensation circuitry, between the reference generator and the amplification circuitry, to vary the loop gain of the feedback control system as a function of the reference magnitude

Axial currents and nuclear spin orientation

International Nuclear Information System (INIS)

Minamisono, T.; Nojiri, Y.; Matsuta, K.

1984-01-01

This paper discusses the symmetries in the phenomena in which weak interaction is involved are largely violated, and it is still the up-to-date fore-front to study the structure of the nuclear weak currents and to learn the limitations on the applicabilities of the various relevant conservation laws as well as the nuclear structures studied by the β-decay. In this meeting, research works on the β-decay processes for the past 10 years have focused on the recoil order experiments designed to determine the limits of validity of the conserved vector current (CVC) theory and to test the G parity conservation i.e. the search for the second class currents (SCC), as well as to study the structure of the axial currents. Concerning the SCC, after intensive studies, but with not conclusive results, on the ft values of mirror β-decays in the early seventies, the correlation-type measurements on mass A=8, 12, 19 and 20 systems have been also carried out in various laboratories from 1975. Among those, concerns have been with the mass A=12 nuclear triad, /sup 12/B-/sup 12/C-/sup 12/N, the energy diagram of which is well known. The choice of this triad is because of the test done for the strong CVC predictions using the spectrum shapes of β-rays combined with the experimental analogue γ-width in /sup 12/C as well as those relevant nuclear structures. Thus, this A=12 system provides the best testing ground for the research described above

Eddy current damping for magnetic levitation: downscaling from macro- to micro-levitation

International Nuclear Information System (INIS)

Elbuken, C; Khamesee, M B; Yavuz, M

2006-01-01

Magnetic levitation of miniaturized objects is investigated in this paper. A magnetic levitation setup is built to implement one-dimensional magnetic levitation motion. It was observed that as the levitated object becomes smaller, magnetic levitation suffers more from undesired vibrations. As a solution, eddy current damping is offered and implemented successfully by placing conductive plates close to the levitated object. An analytical expression for damping coefficient is derived. Experimentally, it is shown that eddy current damping can reduce the RMS positioning error to the level of more than one third of its original value for a 0.386 g object levitated in an air-gap region of 290 mm. The proposed system has the potential to be used for micro-manipulation purposes in a high motion range of 39.8 mm

Eddy current damping for magnetic levitation: downscaling from macro- to micro-levitation

Energy Technology Data Exchange (ETDEWEB)

Elbuken, C; Khamesee, M B; Yavuz, M [Department of Mechanical and Mechatronics Engineering, University of Waterloo, Ontario (Canada)

2006-09-21

Magnetic levitation of miniaturized objects is investigated in this paper. A magnetic levitation setup is built to implement one-dimensional magnetic levitation motion. It was observed that as the levitated object becomes smaller, magnetic levitation suffers more from undesired vibrations. As a solution, eddy current damping is offered and implemented successfully by placing conductive plates close to the levitated object. An analytical expression for damping coefficient is derived. Experimentally, it is shown that eddy current damping can reduce the RMS positioning error to the level of more than one third of its original value for a 0.386 g object levitated in an air-gap region of 290 mm. The proposed system has the potential to be used for micro-manipulation purposes in a high motion range of 39.8 mm.

Current distribution in Cable-In-Conduit Conductors

International Nuclear Information System (INIS)

Ferri, M.A.

1994-05-01

A numerical study of the current distribution in Cable-In-Conduit Conductors (CICC's) experiencing linearly ramping transport currents and transverse magnetic fields was conducted for both infinitely long, periodic cables and finite length cables terminated in low resistance joints. The goal of the study was to gain insight into the phenomenon known as Ramp Rate Limitation, an as yet unexplained correspondence between maximum attainable current and the ramp time taken to reach that current in CICC superconducting magnets. A discrete geometric model of a 27 strand multiply twisted CICC was developed to effectively represent the flux linkages, mutual inductances, and resistive contact points between the strands of an experimentally tested cable. The results of the numerical study showed that for fully periodic cables, the current imbalances due to ramping magnetic fields and ramping transport currents are negligible in the range of experimentally explored operating conditions. For finite length, joint terminated cables, however, significant imbalances can exist. Unfortunately, quantitative results are limited by a lack of knowledge of the transverse resistance between strands in the joints. Nonetheless, general results are presented showing the dependency of the imbalance on cable length, ramp time, and joint resistance for both ramping transverse magnet fields and ramping transport currents. At the conclusion of the study, it is suggested that calculated current imbalances in a finite length cable could cause certain strands to prematurely ''quench'' -- become non-superconducting --thus leading to an instability for the entire cable. This numerically predicted ''current imbalance instability'' is compared to the experimentally observed Ramp Rate Limitation for the 27 strand CICC sample

Recent progress in lower hybrid current drive theory and experiments

International Nuclear Information System (INIS)

Barbato, E.

1998-01-01

In this paper lower hybrid current drive (LHCD) experimental milestones paving the way for future experiments are briefly summarized. The current drive efficiency scaling with the electron temperature is discussed. The role of wave propagation in determining the power deposition profile is stressed and methods are discussed to control the current density profile. Modelling of negative central shear configurations, experimentally obtained by LHCD, are reported. A good agreement is found between the modelling results and the experimental findings, thus showing that a good degree of understanding has been achieved in LHCD theory. (author)

Framing Social Values: An Experimental Study of Culture and Cognition

Science.gov (United States)

Stolte, John F.; Fender, Shanon

2007-01-01

How and why does a given social value come to shape the way an individual thinks, feels, and acts in a specific social situation? This study links ideas from Goffman's frame analysis to other lines of research, proposing that dramatic narratives of variable content, vividness, and language-in-use produce variation in the accessibility of…

Alternating-current transport losses of melt-cast processed Bi-2212 bulk superconductor bars

International Nuclear Information System (INIS)

Tsukamoto, T; Inada, R; Inagaki, N; Andoh, H; Sugiura, T; Oota, A

2003-01-01

Using a melt-casting method, we have fabricated two pieces of Bi-2212 bulk superconductor bar with square and rectangular cross-sections, and we have investigated the alternating-current (ac) transport self-field losses at 77 K. Despite the main contribution of hysteresis loss of the superconductor, there is some difference in the loss behaviour between these two samples. To elucidate the origin, we make numerical calculations on the ac transport self-field losses as a function of current amplitude I 0 below the critical current I c . At a fixed I 0 , the calculated values using the uniform J c distribution and the actual cross-sectional geometry are much higher than the experimental data for the sample with a square cross-section 7.5 x 7.5 mm 2 , while there is good agreement between the calculation and the experiment for the sample with a rectangular cross-section 4.5 x 13.6 mm 2 . The discrepancy appearing in the sample with a square cross-section is ascribed to the actual J c distribution, which is confirmed by critical current measurements when scraping off the sample. The local J c value decreases significantly in going from the surface to the interior of the sample. This suppresses the extension of the flux-penetration region to the interior under ac current transmission and lowers the loss generation compared with the calculated results obtained by the uniform J c distribution

Neutral currents without gauge theory prejudices

International Nuclear Information System (INIS)

Sakurai, J.J.

1976-01-01

The measurement of weak neutral current processes allows a determination of the space-time structure and the isospin structure of these currents. The inclusive production data and the elastic neutrino electron scattering rules out a pure V or A structure of the current. A pure isoscalar current is in disagreement with the experimental data for the one pion production off neutrinos. Further aspects of the neutral current can be determined in neutrino-nucleus-scattering experiments. (BJ) [de

Self-Service Banking: Value Creation Models and Information Exchange

Directory of Open Access Journals (Sweden)

Ragnvald Sannes

2001-01-01

Full Text Available This paper argues that most banks have failed to exploit the potential of self-service banking because they base their service design on an incomplete business model for self-service. A framework for evaluation of self-service banking concepts is developed on the basis of Stabell and Fjeldstad's three value configurations. The value network and the value shop are consistent with self-service banking while the value chain is inappropriate. The impact of the value configurations on information exchange and self-service functionality is discussed, and a framework for design of such services proposed. Current self-service banking practices are compared to the framework, and it is concluded that current practice matches the concept of a value network and not the value shop. However, current practices are only a partial implementation of a value network-based self-service banking concept.

High-voltage high-current triggering vacuum switch

International Nuclear Information System (INIS)

Alferov, D.F.; Bunin, R.A.; Evsin, D.V.; Sidorov, V.A.

2012-01-01

Experimental investigations of switching and breaking capacities of the new high current triggered vacuum switch (TVS) are carried out at various parameters of discharge current. It has been shown that the high current triggered vacuum switch TVS can switch repeatedly a current from units up to ten kiloampers with duration up to ten millisecond [ru

Thermal drift reduction with multiple bias current for MOSFET dosimeters

Energy Technology Data Exchange (ETDEWEB)

Carvajal, M A; Martinez-Olmos, A; Morales, D P; Lopez-Villanueva, J A; Palma, A J [Departamento de Electronica y TecnologIa de Computadores, ETSIIT, Universidad de Granada, E-18071 Granada (Spain); Lallena, A M, E-mail: carvajal@ugr.es [Departamento de Fisica Atomica, Molecular y Nuclear, Universidad de Granada, E-18071 Granada (Spain)

2011-06-21

New thermal compensation methods suitable for p-channel MOSFET (pMOS) dosimeters with the usual dose readout procedure based on a constant drain current are presented. Measuring the source-drain voltage shifts for two or three different drain currents and knowing the value of the zero-temperature coefficient drain current, I{sub ZTC}, the thermal drift of source-drain or threshold voltages can be significantly reduced. Analytical expressions for the thermal compensation have been theoretically deduced on the basis of a linear dependence on temperature of the parameters involved. The proposed thermal modelling has been experimentally proven. These methods have been applied to a group of ten commercial pMOS transistors (3N163). The thermal coefficients of the source-drain voltage and the threshold voltage were reduced from -3.0 mV deg. C{sup -1}, in the worst case, down to -70 {mu}V deg. C{sup -1}. This means a thermal drift of -2.4 mGy deg. C{sup -1} for the dosimeter. When analysing the thermal drifts of all the studied transistors, in the temperature range from 19 to 36 deg. C, uncertainty was obtained in the threshold voltage due to a thermal drift of {+-}9mGy (2 SD), a commonly acceptable value in most radiotherapy treatments. The procedures described herein provide thermal drift reduction comparable to that of other technological or numerical strategies, but can be used in a very simple and low-cost dosimetry sensor.

Experimental Investigation of the Performance of Tilt Current Meters in Wave-Dominated Flows

DEFF Research Database (Denmark)

Hansen, Asger Bendix; Carstensen, Stefan

2017-01-01

In recent years, tilt current meters (TCMs) have received renewed attention as they provide an inexpensive method for measuring currents in the coastal zone. However, previous studies focused mainly on current dominated flows or the current component of the flow. This study investigates the perfo...

Spatially resolved determination of the short-circuit current density of silicon solar cells via lock-in thermography

International Nuclear Information System (INIS)

Fertig, Fabian; Greulich, Johannes; Rein, Stefan

2014-01-01

We present a spatially resolved method to determine the short-circuit current density of crystalline silicon solar cells by means of lock-in thermography. The method utilizes the property of crystalline silicon solar cells that the short-circuit current does not differ significantly from the illuminated current under moderate reverse bias. Since lock-in thermography images locally dissipated power density, this information is exploited to extract values of spatially resolved current density under short-circuit conditions. In order to obtain an accurate result, one or two illuminated lock-in thermography images and one dark lock-in thermography image need to be recorded. The method can be simplified in a way that only one image is required to generate a meaningful short-circuit current density map. The proposed method is theoretically motivated, and experimentally validated for monochromatic illumination in comparison to the reference method of light-beam induced current.

Value definitions and consumer consciousness

OpenAIRE

Wakenshaw, Susan Y. L.; Phillips, Laura; Ng, Irene C. L.

2014-01-01

This paper contributes to the understanding of value within the service science and management literature, a literature that currently defines and measures value in various ways, making assumptions about how value is created and judged. We present this paper in two parts: in the first, we reprise six core themes of value understanding in the management literature, highlighting their implicit philosophical, chronological and consciousness assumptions; in the second, we elaborate on consciousne...

Experimental identification of the kink instability as a poloidal flux amplification mechanism for coaxial gun spheromak formation

International Nuclear Information System (INIS)

Hsu, S.C.; Bellan, P.M.

2003-01-01

The magnetohydrodynamic kink instability is observed and identified experimentally as a poloidal flux amplification mechanism for coaxial gun spheromak formation. Plasmas in this experiment fall into three distinct regimes which depend on the peak gun current to magnetic flux ratio, with (I) low values resulting in a straight plasma column with helical magnetic field, (II) intermediate values leading to kinking of the column axis, and (III) high values leading immediately to a detached plasma. Onset of column kinking agrees quantitatively with the Kruskal-Shafranov limit, and the kink acts as a dynamo which converts toroidal to poloidal flux. Regime II clearly leads to both poloidal flux amplification and the development of a spheromak configuration

Experimental identification of the kink instability as a poloidal flux amplification mechanism for coaxial gun spheromak formation.

Science.gov (United States)

Hsu, S C; Bellan, P M

2003-05-30

The magnetohydrodynamic kink instability is observed and identified experimentally as a poloidal flux amplification mechanism for coaxial gun spheromak formation. Plasmas in this experiment fall into three distinct regimes which depend on the peak gun current to magnetic flux ratio, with (I) low values resulting in a straight plasma column with helical magnetic field, (II) intermediate values leading to kinking of the column axis, and (III) high values leading immediately to a detached plasma. Onset of column kinking agrees quantitatively with the Kruskal-Shafranov limit, and the kink acts as a dynamo which converts toroidal to poloidal flux. Regime II clearly leads to both poloidal flux amplification and the development of a spheromak configuration.

Limiting currents in superconducting composites

International Nuclear Information System (INIS)

Keilin, V.E.; Romanovskii, V.R.

1992-01-01

In this paper the results of numerical and analytical calculations of the process of current charging into a round superconducting composite with properties homogenized over cross-section are presented. In the numerical solution taken was into account a common proceeding of the thermal and electromagnetic processes. A wire with real volt-ampere characteristics approximated by exponential dependence was considered. The calculations carried out at various rates of current charging, voltampere characteristics, matrix materials, heat transfer coefficients and other parameters showed: the existence of characteristic limiting value of current below which the wire remains in a superconducting state if the current charging ceases and above which changes into a normal state; this current is somewhat less than a quench current; the existence of finite value for limiting current at any low heat transfer from a surface. The analytical solution of the problem is given. It permitted to write the stability criterion from which the dependence of limiting currents on initial parameters follows. The wire nonisothermality, its heat capacity, thermal and electric conductivities are taken into account additionally, as compared to results published earlier

Experimental study of an electromagnetic flow meter for liquid metals based on torque measurement during pumping process

International Nuclear Information System (INIS)

Dubovikova, N; Kolesnikov, Y; Karcher, Ch

2015-01-01

This paper presents a detailed experimental study on an electromagnetic flow measurement technique to measure the flow rate of liquid metals. The experimental setup consists of a contactless electromagnetic pump with a torque sensor mounted on the pump shaft. The electromagnetic pump is composed of two rotating steel discs having embedded permanent magnets with alternating poles. The rotation of the discs creates a travelling sinusoidal magnetic field and eddy currents within the liquid metal. The metal is contained inside the duct located between the discs of the pump. The interaction of the magnetic field and the induced eddy currents generates an electromagnetic Lorentz force providing the pumping effect. The flow rate is proportional to this force. The torque sensor measures the moment of the discs due to the Lorentz force, which is converted to a flow rate value. We name the method Lorentz torque velocimetry (LTV). The full calibration procedure and experimental investigation of the LTV are described. The method can be used as a non-contact flow rate control technique for liquid metals. (paper)

Experimental analysis on the performance of lithium based batteries for road full electric and hybrid vehicles

International Nuclear Information System (INIS)

Capasso, Clemente; Veneri, Ottorino

2014-01-01

Highlights: • Performance analysis for lithium storage technologies, such as Li[NiCoMn]O 2 and LiFePO 4 batteries. • Actual capacity of lithium technologies analyzed almost close to their nominal capacity also for high discharging current. • The charging efficiency for Li[NiCoMn]O 2 positively affects the regenerative breaking and fast recharging operations. • The analyzed battery packs follow dynamic power requirements on performed road driving cycles. • Experimental results demonstrate driving range is much higher when battery packs are based on lithium technology. - Abstract: This paper deals with an experimental evaluation regarding the real performance of lithium based energy storage systems for automotive applications. In particular real working operations of different lithium based storage system technologies, such as Li[NiCoMn]O 2 and LiFePO 4 batteries, are compared in this work from the point of view of their application in supplying full electric and hybrid vehicles, taking as a reference the well-known behavior of lead acid batteries. For this purpose, the experimental tests carried out in laboratory are firstly performed on single storage modules in stationary conditions. In this case the related results are obtained by means of a bidirectional cycle tester based on the IGBT technology, and consent to evaluate, compare and contrast charge/discharge characteristics and efficiency at constant values of current/voltage/power for each storage technology analyzed. Then, lithium battery packs are tested in supplying a 1.8 kW electric power train using a laboratory test bench, based on a 48 V DC bus and specifically configured to simulate working operations of electric vehicles on the road. For this other experimentation the test bench is equipped with an electric brake and acquisition/control system, able to represent in laboratory the real vehicle conditions and road characteristics on predefined driving cycles at different slopes. The obtained

Glazed clay pottery and lead exposure in Mexico: Current experimental evidence.

Science.gov (United States)

Diaz-Ruiz, Araceli; Tristán-López, Luis Antonio; Medrano-Gómez, Karen Itzel; Torres-Domínguez, Juan Alejandro; Ríos, Camilo; Montes, Sergio

2017-11-01

Lead exposure remains a significant environmental problem; lead is neurotoxic, especially in developing humans. In Mexico, lead in human blood is still a concern. Historically, much of the lead exposure is attributed to the use of handcrafted clay pottery for cooking, storing and serving food. However, experimental cause-and-effect demonstration is lacking. The present study explores this issue with a prospective experimental approach. We used handcrafted clay containers to prepare and store lemonade, which was supplied as drinking water to pregnant rats throughout the gestational period. We found that clay pots, jars, and mugs leached on average 200 µg/l lead, and exposure to the lemonade resulted in 2.5 µg/dl of lead in the pregnant rats' blood. Neonates also showed increased lead content in the hippocampus and cerebellum. Caspase-3 activity was found to be statistically increased in the hippocampus in prenatally exposed neonates, suggesting increased apoptosis in that brain region. Glazed ceramics are still an important source of lead exposure in Mexico, and our results confirm that pregnancy is a vulnerable period for brain development.

Manufacture of an experimental platform with ECR ion source

International Nuclear Information System (INIS)

Zhou Changgeng; Hu Yonghong; Li Yan

2007-12-01

The working principle and basal configuration and fabricative process of ECR ion source are introdced. Regarding as an experimental and test device, the experimental platform of ECR ion source may expediently regulate every parameter of ion source, and achieve good character of beam current. Through improving on the components, ECR ion source can is modulated in best state. Above results may be used in the running and debugging of neutron generator. Therefore, the experimental platform of ECR ion source is the necessary equipment of large beam current neutron generator. Comparing the experimental platform of ECR ion source with domestic ones and the overseas ones, it mainly be used in the simulation experiments about neutron generator. It is compact and experimental platform mode in structure. It can focus the beam current and measure many parameters on line in function. The problem of lower beam current to discover is resolved in debugging of the device. The measurement results indicate that the technology character of the device have achieved design requirements. (authors)

CALCULATION AND EXPERIMENTAL ESTIMATION OF RESULTS OF ELECTRO-THERMAL ACTION OF RATIONED BY THE INTERNATIONAL STANDARD IEC 62305-1-2010 IMPULSE CURRENT OF SHORT BLOW OF ARTIFICIAL LIGHTNING ON THE THIN-WALLED COVERAGE FROM STAINLESS STEEL

Directory of Open Access Journals (Sweden)

M. I. Baranov

2017-03-01

probed pre-production steel models electric charge of qL numeral changed from 44,2 Kl to 81,3 Kl. It is shown that direct influence rationed by the International Standard IEC 62305-1-2010 impulse of current of short blow of artificial lightning with in-use PTP on the indicated pre-production steel models causes in them the rounded small hole of melting of surface of coverage a depth no more than 50 μm and diameter no more than 60 mm. The results of calculation and experiment coincide within the limits of 5 %. Originality. First in world practice on the unique generator of LIC of short blow of artificial lightning of type of GITM-10/350 experimental researches of electro-thermal resistibility of pre-production sheet models of outward roof are conducted TO of stainless steel 12Х18Н10Т is easily soiled to direct action on them of impulses of current of an artificial storm air spark digit with extreme parameters. Practical value. Drawing on the got results in practice of protection height TO from linear lightning will allow substantially to promote their functional and fire-prevention safety in the conditions of direct action on them of the plasma ductings of high current storm air spark discharge.

Stability, reliability and validity of social value orientation

NARCIS (Netherlands)

Bekkers, René

2004-01-01

Social value orientations are often regarded as stable individual differences in otherregarding preferences - the concern for equality and joint outcomes - affecting the propensity to cooperate in experimental social dilemma situations. Despite the widespread use of measures of social value

Modulational instability development and current drive

International Nuclear Information System (INIS)

Popel, S.I.; Vladimirov, S.V.; Tsytovich, V.N.

1992-01-01

Recently many investigations on current driven by lower-hybrid (LH) waves in a plasma of toroidal nuclear fusion installations are carried out. Usually a theoretical approach taking into account quasilinear and binary collisions effects is used to describe current drive. However a problem of comparison of the results obtained with the aid of the above theoretical approach and experimental data takes place. Namely the experimentally observed currents driven by LH waves is two-three orders of magnitude larger than those calculated. The above discrepancy between theory and experiment is related with the existence of the so-called ''spectral gap'', that is the gap between the parallel phase velocities of LH waves ω/k || (where ω, k || are LH wave frequency and a component of wavenumber k parallel to the external magnetic field) which are necessary for effective Landau damping of LH waves (i.e. velocities as high as several electron thermal velocities) and the lowest parallel phase velocity in the injected LH wave spectrum. Experimentally observed current drive may be explained if one accounts for filling of the ''spectral gap'' by LH waves. Some nonlinear effects have been drawn in current drive description to explain the ''spectral gap'' filling by LH waves. However the LH wave modulational instability (MI) effect has not been considered yet in application to current drive description. The aim of this paper is to investigate this MI influence. We shall show that for sufficiently intensive pump level of LH wave the MI can lead to ''spectral gap'' filling. (author) 4 refs

A matrix model for valuing anesthesia service with the resource-based relative value system

Directory of Open Access Journals (Sweden)

Sinclair DR

2014-10-01

Full Text Available David R Sinclair,1 David A Lubarsky,1 Michael M Vigoda,1 David J Birnbach,1 Eric A Harris,1 Vicente Behrens,1 Richard E Bazan,1 Steve M Williams,1 Kristopher Arheart,2 Keith A Candiotti1 1Department of Anesthesiology, Perioperative Medicine and Pain Management, 2Department of Public Health Sciences, Division of Biostatistics, University of Miami Miller School of Medicine, Miami, FL, USA Background: The purpose of this study was to propose a new crosswalk using the resource-based relative value system (RBRVS that preserves the time unit component of the anesthesia service and disaggregates anesthesia billing into component parts (preoperative evaluation, intraoperative management, and postoperative evaluation. The study was designed as an observational chart and billing data review of current and proposed payments, in the setting of a preoperative holing area, intraoperative suite, and post anesthesia care unit. In total, 1,195 charts of American Society of Anesthesiology (ASA physical status 1 through 5 patients were reviewed. No direct patient interventions were undertaken. Results: Spearman correlations between the proposed RBRVS billing matrix payments and the current ASA relative value guide methodology payments were strong (r=0.94–0.96, P<0.001 for training, test, and overall. The proposed RBRVS-based billing matrix yielded payments that were 3.0%±1.34% less than would have been expected from commercial insurers, using standard rates for commercial ASA relative value units and RBRVS relative value units. Compared with current Medicare reimbursement under the ASA relative value guide, reimbursement would almost double when converting to an RBRVS billing model. The greatest increases in Medicare reimbursement between the current system and proposed billing model occurred as anesthetic management complexity increased. Conclusion: The new crosswalk correlates with existing evaluation and management and intensive care medicine codes in an

Superallowed 0+→0+ nuclear β decays: A critical survey with tests of the conserved vector current hypothesis and the standard model

International Nuclear Information System (INIS)

Hardy, J.C.; Towner, I.S.

2005-01-01

A complete and critical survey is presented of all half-life, decay-energy, and branching-ratio measurements related to 20 superallowed 0 + →0 + decays; no measurements are ignored, although some are rejected for cause and others updated. A new calculation of the statistical rate function f is described and experimental ft values determined. The associated theoretical corrections needed to convert these results into 'corrected' Ft values are discussed, and careful attention is paid to the origin and magnitude of their uncertainties. As an exacting confirmation of the conserved vector current hypothesis, the corrected Ft values are seen to be constant to three parts in 10 4 . These data are also used to set a new limit on any possible scalar interaction (assuming maximum parity violation) of C S /C V =-(0.00005±0.00130). The average Ft value obtained from the survey, when combined with the muon lifetime, yields the up-down quark-mixing element of the Cabibbo-Kobayashi-Maskawa (CKM) matrix, V ud =0.9738±0.0004, and the unitarity test on the top row of the matrix becomes vertical bar V ud vertical bar 2 + vertical bar V us vertical bar 2 + vertical bar V ub vertical bar 2 =0.9966±0.0014 using the Particle Data Group's currently recommended values for V us and V ub . If V us comes instead from two recent results on K e3 decay, the unitarity sum becomes 0.9996(11). Either result can be expressed in terms of the possible existence of right-hand currents. Finally, we discuss the priorities for future theoretical and experimental work with the goal of making the CKM unitarity test more definitive

FUZZY LOGIC BASED OPTIMIZATION OF CAPACITOR VALUE FOR SINGLE PHASE OPEN WELL SUBMERSIBLE INDUCTION MOTOR

Directory of Open Access Journals (Sweden)

R. Subramanian

2011-01-01

Full Text Available Purpose – The aim of this paper is to optimize the capacitor value of a single phase open well submersible motor operating under extreme voltage conditions using fuzzy logic optimization technique and compared with no-load volt-ampere method. This is done by keeping the displacement angle (a between main winding and auxiliary winding near 90o, phase angle (f between the supply voltage and line current near 0o. The optimization work is carried out by using Fuzzy Logic Toolbox software built on the MATLAB technical computing environment with Simulink software. Findings – The optimum capacitor value obtained is used with a motor and tested for different supply voltage conditions. The vector diagrams obtained from the experimental test results indicates that the performance is improved from the existing value. Originality/value – This method will be highly useful for the practicing design engineers in selecting the optimum capacitance value for single phase induction motors to achieve the best performance for operating at extreme supply voltage conditions.

Current Capability of Atomic Structure Theory

International Nuclear Information System (INIS)

Kim, Yong Ki

1993-01-01

Current capability of atomic structure theory is reviewed, and advantages, disadvantages and major features of popular atomic structure codes described. Comparisons between theoretical and experimental data on transition energies and lifetimes of excited levels are presented to illustrate the current capability of atomic structure codes.

Problems of the experimental implementation of MTJ

International Nuclear Information System (INIS)

Mazaletskiy, L A; Rudy, A S; Trushin, O S; Naumov, V V; Mironenko, A A; Vasilev, S V

2015-01-01

The results of experimental studies of MRAM technology based on standard magnetic tunneling junctions are presented. Basic steps of experimental fabrication of MRAM cell are considered. Experimental samples of MTJ with variable lateral sizes are fabricated. Current-voltage characteristics of the tunnel barriers are investigated. Main parameters of the tunnel barriers are estimated from comparison of the experimental data with the theory. (paper)

Investigation of leakage current and breakdown voltage in irradiated double-sided 3D silicon sensors

International Nuclear Information System (INIS)

Betta, G.-F. Dalla; Mendicino, R.; Povoli, M.; Sultan, D.M.S.; Ayllon, N.; Hoeferkamp, M.; McDuff, H.; Seidel, S.; Boscardin, M.; Zorzi, N.; Mattiazzo, S.

2016-01-01

We report on an experimental study aimed at gaining deeper insight into the leakage current and breakdown voltage of irradiated double-sided 3D silicon sensors from FBK, so as to improve both the design and the fabrication technology for use at future hadron colliders such as the High Luminosity LHC. Several 3D diode samples of different technologies and layout are considered, as well as several irradiations with different particle types. While the leakage current follows the expected linear trend with radiation fluence, the breakdown voltage is found to depend on both the bulk damage and the surface damage, and its values can vary significantly with sensor geometry and process details.

YBCO SQUIDs with unconventional current phase relation

International Nuclear Information System (INIS)

Bauch, T.; Johansson, J.; Cedergren, K.; Lindstroem, T.; Lombardi, F.

2007-01-01

We have studied the dynamics of YBa 2 Cu 3 O 7-δ (YBCO) dc sperconducting quantum interference devices (SQUIDs) characterized by an unconventional Josephson current phase relation (CPR). We have focused on SQUID configurations with Josephson junctions where the lobe of the order parameter in one electrode is facing a node in the other electrode. This order parameter arrangement should enhance the appearance of a sin(2φ) term in the CPR. The response of the critical current of the dc SQUID, under the effect of an external magnetic field, has been measured in temperature, down to 20 mK. Our experimental data have been compared with numerical simulations of the SQUIDs dynamics by considering a CPR of a single junction of the form I(φ) = I I sin(φ) - I II sin(2φ) where I I and I II are, respectively, the first and second harmonic component. In our devices the values of the sin(2φ) term are such that the fundamental state of the SQUID is naturally double degenerate. This is of great relevance for applications of d-wave SQUIDs in quantum information processing

INVESTIGATION OF PROPERTIES OF CURRENT COLLECTOR ELEMENTS AND THEIR EFFECT ON THE PERFORMANCE OF TRIBOSYSTEM «CONTACT WIRE - CURRENT COLLECTOR ELEMENT»

Directory of Open Access Journals (Sweden)

Yu. L. Bolshakov

2015-11-01

Full Text Available Purpose. The paper is devoted to the detailed analysis of interrelations at the contact point of friction pair «contact wire – current collector insert». In the work it is necessary: 1 to examine quality of manufacturing of specimens of current collector elements from different manufacturers; 2 to narrow the range of hardness for carbon inserts; 3 to develop a technique of sorting carbon current collector inserts for the structural parameters. Methodology. The executed work was based on the use of the theory of reliability of technical systems and electromechanical processes. Findings. The paper studies the interrelation at the contact point of friction pair «contact wire – current col lector insert», the connection was established between the hardness and electrical resistivity. It is proposed to narrow the range of carbon inserts hardness. The method of sorting coal collector inserts in hardness was developed, and the research has revealed the discrepancy of current collector inserts with existing regulations. It was proposed to equip the pantographs slide with current collector elements using special scheme and to develop a specialized research facility, which will be possible to conduct studies of the interaction of the friction pair «contact wire – current collector insert». Originality. In the course of the study the current collector inserts the sharp structural heterogeneity and fluctuations of the density of the material along the length of the insert were established. The dependence between hardness of inserts and electrical resistivity was established. It was analyzed and concluded about the need to reduce the values of the normal range of hardness. Based on the results of the research, the experimental dependences were obtained and proposed the method for sorting carbon current collector inserts for the structural parameters. Practical value. The obtained results of coal current collector inserts define the need to use

Study, design and manufacture eddy current probes for industry applications

International Nuclear Information System (INIS)

Nguyen Phuc; Nguyen Van Thuy; Vuong Binh Duong; Do Minh Duc; Trinh Dinh Truong; Tran Trong Duc; Do Tung Khanh; Dang Quang Trung

2016-01-01

This study is based on the studying, designing and manufacturing of eddy current probes for industry applications. The main tasks of this study include: i) Describes the overview and classification of eddy current probes (which can be classified into three categories based on the mode of operation: absolute eddy current probe, differential eddy current probe and reflect eddy current probe); ii) Describes the three methods of probe designing and manufacturing (including experimental, analytical and numerical designs); iii) Describes the designing and manufacturing of eddy current probes for industry applications, which based on experimental and analytical methods. Based on this study, we have successfully manufactured some current probes (including absolute eddy current probe, differential eddy current probe and reflect eddy current probe) for surface and tube inspections. (author)

Lower hybrid current drive in tokamak plasmas

Energy Technology Data Exchange (ETDEWEB)

Ushigusa, Kenkichi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

1999-03-01

Past ten years progress on Lower Hybrid Current Drive (LHCD) experiments have demonstrated the largest non-inductive current (3.6 MA, JT-60U), the longest current sustainment (2 hours, TRIAM-1M), non-inductive current drive at the highest density (n-bar{sub e} - 10{sup 20}m{sup -3}, ALCATOR-C) and the highest current drive efficiency ({eta}{sub CD} = 3.5x10{sup 19} m{sup -2}A/W, JT-60). These results indicate that LHCD is one of the most promising methods to drive non-inductive current in the present tokamak plasmas. This paper presents recent experimental results on LHCD experiments. Basic theories of LH waves, the wave propagation and the current drive are briefly summarized. The main part of this paper describes several important results and their physical pictures on recent LHCD experiments; 1) the experimental set-up, 2) the current drive efficiency, 3) the control of current profile and MHD activities, 4) the global energy confinement, 5) the global power flow, 6) fast electron behavior, 7) interaction between LH waves and thermal/fast ions, 8) combination with other CD method. (author)

Higher-order relationship between eigen-value separation and static flux tilts

International Nuclear Information System (INIS)

Beckner, W.D.

1975-01-01

Spatial kinetics phenomena in nuclear reactors, such as xenon-induced spatial flux oscillations, are currently being analyzed using the higher harmonic solutions to the static reactor balance equation. An important parameter in such an analysis is a global quantity called eigenvalue separation. It is desirable to be able to experimentally measure this parameter in power reactors in order to confirm design calculations. Since spatial distortions in the flux shape depend on the eigenvalue separation of the reactor, an attempt has been made previously to use this fact as a means of measuring the parameter. It was postulated that an induced flux distortion or ''static flux tilt'' could be measured and theoretically related to eigenvalue separation. Unfortunately, the behavior of experimental data did not exactly agree with theoretical predictions, and values of the parameter found using the original static flux tilt technique were consistently low. The theory has been re-evaluated here and the previously observed discrepancy eliminated. Techniques have been also developed to allow for more accurate interpretation of experimental data. In order to make the method applicable to real systems, the theory has been extended to two spatial dimensions; extension to three dimensions follows directly. Possible trouble areas have been investigated, and experimental procedures for use of the technique to measure the eigenvalue separation in power reactors are presented

Self-similar current decay experiment in RFX-mod

International Nuclear Information System (INIS)

Zanca, Paolo

2007-01-01

The self-similar current decay (SSCD) has been suggested as a promising operation for reversed field pinch devices by numerical simulations, which show a decrease in modes amplitude and stochasticity when the magnetic field is forced to decay at a suitable rate at a fixed radial profile (Nebel et al 2002 Phys. Plasmas 9 4968). The first experimental test of SSCD has recently been performed in RFX-mod. An initial fast decrease in the mode amplitudes (about 40% of the initial value) is observed. After that, a regime characterized by transient states close to the single-helicity condition (Cappello and Paccagnella 1992 Phys. Fluids B 4 611, Finn et al 1992 Phys. Fluids B 4 1262) is established. This brings about a 50% increase in the global confinement parameters

Charged current weak interactions at high energy

International Nuclear Information System (INIS)

Cline, D.

1977-01-01

We review high energy neutrino and antineutrino charged current interactions. An overview of the experimental data is given, including a discussion of the experimental status of the y anomaly. Locality tests, μ-e universality and charge symmetry invariance tests are discussed. Charm production is discussed. The experimental status of trimuon events and possible phenomenological models for these events are presented. (orig.) [de

Currents, HF Radio-derived, Monterey Bay, 25 hr, Zonal, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 25 hour running average of the zonal component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN...

Currents, HF Radio-derived, Ano Nuevo, 25 hr, Zonal, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 25 hour running average of the zonal component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN...

Currents, HF Radio-derived, SF Bay, 33 hr, Meridional, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 33 hour running average of the meridional component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN...

Currents, HF Radio-derived, SF Bay, 25 hr, Zonal, EXPERIMENTAL

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The data is the 25 hour running average of the zonal component of ocean surface currents derived from High Frequency Radio-derived measurements. THIS IS AN...

Experimental evaluation of IGBT junction temperature measurement via peak gate current

DEFF Research Database (Denmark)

Baker, Nick; Munk-Nielsen, Stig; Iannuzzo, Francesco

2015-01-01

Temperature sensitive electrical parameters allow junction temperature measurements on power semiconductors without modification to module packaging. The peak gate current has recently been proposed for IGBT junction temperature measurement and relies on the temperature dependent resistance...... of the gate pad. Consequently, a consideration of chip geometry and location of the gate pad is required before interpreting temperature data from this method. Results are also compared with a traditional electrical temperature measurement method: the voltage drop under low current....

Current and Current Fluctuations in Quantum Shuttles

DEFF Research Database (Denmark)

Jauho, Antti-Pekka; Flindt, Christian; Novotny, Tomas

2005-01-01

theoretical tools needed for the analysis, e.g., generalized master equations and Wigner functions, and we outline the methods how the resulting large numerical problems can be handled. Illustrative results are given for current, noise, and full counting statistics for a number of model systems. Throughout...... the review we focus on the physics behind the various approximations, and some simple examples are given to illustrate the theoretical concepts. We also comment on the experimental situation. ©2005 American Institute of Physics...

Exploring Work Values: Helping Students Articulate Their Good (Work) Life

Science.gov (United States)

Carlstrom, Aaron H.; Hughey, Kenneth F.

2014-01-01

The current article builds on "Living the Good (Work) Life: Implications of General Values for Work Values" (Carlstrom, 2011) by presenting ways to address work values in career advising. The following questions are addressed in the current article: When should students explore work values in career advising? What career development and…

Current sharing effect on the current instability and allowable temperature rise of composite high-TC superconductors

International Nuclear Information System (INIS)

Romanovskii, V.R.; Watanabe, K.; Awaji, S.; Nishijima, G.; Takahashi, Ken-ichiro

2004-01-01

To understand the basic mechanisms of the thermal runaway phenomenon, the limiting margin of the current instability, which may spontaneously occur in composite high-T C superconductors like multifilament Bi-based wire or tape, is derived under DC magnetic field. The current sharing and allowable temperature rise effects were considered. A static zero-dimensional model was utilized to describe the basic formulae dealing with the peculiarities of the non-isothermal change of superconducting composite voltage-current characteristic. The boundary of allowable stable values of the temperature, electric field and current are derived analytically. It was shown that permissible values of the current and electric field might be higher than those determined by use of the standard critical current criterion. In consequence of this feature, the noticeable allowable temperature rise of the composite superconductor before its transition to the normal state may be seen. The criterion for complete thermal stability condition is written describing the state when temperature of the composite equals critical temperature of a superconductor and the transport current flows stably only in matrix. The performed analysis also proves the existence of value of the volume fraction of a superconductor in composite at which its current-carrying capacity has minimum. These peculiarities are due to the stable current redistribution between superconductor and stabilizing matrix. Therefore, the current sharing not only leads to the matrix/superconductor ratio effect on the stable operating characteristics of the composite high-T C superconductors but also becomes important in the adequate description of quench process in the high-T C superconducting magnets

Energy from streaming current and potential

NARCIS (Netherlands)

Olthuis, Wouter; Schippers, Bob; Eijkel, Jan C.T.; van den Berg, Albert

2005-01-01

It is investigated how much energy can be delivered by a streaming current source. A streaming current and subsequent streaming potential originate when double layer charge is transported by hydrodynamic flow. Theory and a network model of such a source is presented and initial experimental results

Electron cyclotron current drive efficiency in an axisymmetric tokamak

Energy Technology Data Exchange (ETDEWEB)

Gutierrez-Tapia, C.; Beltran-Plata, M. [Instituto Nacional de Investigaciones Nucleares, Dept. de Fisica, Mexico D.F. (Mexico)

2004-07-01

The neoclassical transport theory is applied to calculate electron cyclotron current drive (ECCD) efficiency in an axisymmetric tokamak in the low-collisionality regime. The tokamak ordering is used to obtain a system of equations that describe the dynamics of the plasma where the nonlinear ponderomotive (PM) force due to high-power radio-frequency (RF) waves is included. The PM force is produced around an electron cyclotron resonant surface at a specific poloidal location. The ECCD efficiency is analyzed in the cases of first and second harmonics (for different impinging angles of the RF waves) and it is validated using experimental parameter values from TCV and T-10 tokamaks. The results are in agreement with those obtained by means of Green's function techniques. (authors)

Inclusive ϱ0 production in overlineνμp charged current interactions

Science.gov (United States)

Grässler, H.; Lanske, D.; Schulte, R.; Jones, G. T.; Kennedy, B. W.; Middleton, R. P.; O'Neale, S. W.; Böckmann, K.; Gebel, W.; Geich-Gimbel, C.; Hoffmann, E.; Nellen, B.; Saarikko, H.; Klein, H.; Mittendorfer, J.; Morrison, D. R. O.; Schmid, P.; Wachsmuth, H.; Barnham, K. W. J.; Clayton, E. F.; Hamisi, F.; Miller, D. B.; Mobayyen, M. M.; Aderholz, M.; Deck, L.; Schmitz, N.; Wittek, W.; Corrigan, G.; Myatt, G.; Radojicic, D.; Saitta, B.; Wells, J.; Aachen-Birmingham-Bonn-CERN-Imperial College-München (MPI)-Oxford Collaboration

1986-07-01

Inclusive ϱ0 production has been studied in antineutrino-proton charged current interactions, using a sample of 3340 events obtained in BEBC filled with hydrogen and exposed to the CERN wideband antineutrino beam. An average multiplicity of 0.11 ± 0.02 ϱ0 per event at a mean hadronic mass W of 4.2 GeV is observed. The ϱ0 production characteristics are determined as functions of pT, xF, and z. The ratio ϱ 0/"π 0" is found to be low at small z values consistent with centrally produced pions coming mainly from resonances. At large z values this ratio approaches 0.45 ± 0.15 which is compatible with a vector/pseudoscalar meson direct production ratio of one. The results are compared with those obtained from neutrino-proton interactions in the same experimental set-up.