WorldWideScience

Sample records for ctod-based acceptance criteria

  1. CTOD-based acceptance criteria for heat exchanger head staybolts

    International Nuclear Information System (INIS)

    Lam, P.S.; Sindelar, R.L.; Barnes, D.M.; Awadalla, N.G.

    1992-01-01

    The primary coolant piping system of the Savannah River Site (SRS) reactors contains twelve heat exchangers to remove the waste heat from the nuclear materials production. A large break at the inlet or outlet heads of the heat exchangers would occur if the restraint members of the heads become inactive. The heat exchanger head is attached to the tubesheet by 84 staybolts. The structural integrity of the heads is demonstrated by showing the redundant capacity of the staybolts to restrain the head at design conditions and under seismic loadings. The beat exchanger head is analyzed with a three- dimensional finite element model. The restraint provided by the staybolts is evaluated for several postulated cases of inactive or missing staybolts, that is, bolts that have a flaw exceeding the ultrasonic testing (UT) threshold depth of 25% of the bolt diameter. A limit of 6 inactive staybolts is reached with a fracture criterion based on the maximum allowable local displacement at the active staybolts which corresponds to the crack tip opening displacement (CTOD) of 0.032 inches. An acceptance criteria methodology has been developed to disposition flaws reported in the staybolt inspections while ensuring adequate restraint capacity of the staybolts to maintain integrity of the heat exchanger heads against collapse. The methodology includes an approach for the baseline and periodic inspections of the staybolts. A total of up to 6 staybolts, reported as containing flaws with depths at or exceeding 25% would be acceptable in the heat exchanger

  2. Toxic chemical risk acceptance criteria

    International Nuclear Information System (INIS)

    Craig, D.K.; Davis, J.; Lee, L.; Lein, P.; Omberg, S.

    1992-01-01

    This paper presents recommendations of a subcommittee of the Westinghouse M ampersand 0 Nuclear Facility Safety Committee concerning toxic chemical risk acceptance criteria. Two sets of criteria have been developed, one for use in the hazard classification of facilities, and the second for use in comparing risks in DOE non-reactor nuclear facility Safety Analysis Reports. The Emergency Response Planning Guideline (ERPG) values are intended to provide estimates of concentration ranges for specific chemicals above which exposure would be expected to lead to adverse heath effects of increasing severity for ERPG-1, -2, and -3s. The subcommittee recommends that criteria for hazard class or risk range be based on ERPGs for all chemicals. Probability-based Incremental Cancer Risk (ICR) criteria are recommended for additional analyses of risks from all known or suspected human carcinogens. Criteria are given for both on-site and off-site exposure. The subcommittee also recommends that the 5-minute peak concentration be compared with the relevant criterion with no adjustment for exposure time. Since ERPGs are available for only a limited number of chemicals, the subcommittee has developed a proposed hierarchy of concentration limit parameters for the different criteria

  3. DISPOSABLE CANISTER WASTE ACCEPTANCE CRITERIA

    Energy Technology Data Exchange (ETDEWEB)

    R.J. Garrett

    2001-07-30

    The purpose of this calculation is to provide the bases for defining the preclosure limits on radioactive material releases from radioactive waste forms to be received in disposable canisters at the Monitored Geologic Repository (MGR) at Yucca Mountain. Specifically, this calculation will provide the basis for criteria to be included in a forthcoming revision of the Waste Acceptance System Requirements Document (WASRD) that limits releases in terms of non-isotope-specific canister release dose-equivalent source terms. These criteria will be developed for the Department of Energy spent nuclear fuel (DSNF) standard canister, the Multicanister Overpack (MCO), the naval spent fuel canister, the High-Level Waste (HLW) canister, the plutonium can-in-canister, and the large Multipurpose Canister (MPC). The shippers of such canisters will be required to demonstrate that they meet these criteria before the canisters are accepted at the MGR. The Quality Assurance program is applicable to this calculation. The work reported in this document is part of the analysis of DSNF and is performed using procedure AP-3.124, Calculations. The work done for this analysis was evaluated according to procedure QAP-2-0, Control of Activities, which has been superseded by AP-2.21Q, Quality Determinations and Planning for Scientific, Engineering, and Regulatory Compliance Activities. This evaluation determined that such activities are subject to the requirements of DOE/RW/0333P, Quality Assurance Requirements and Description (DOE 2000). This work is also prepared in accordance with the development plan titled Design Basis Event Analyses on DOE SNF and Plutonium Can-In-Canister Waste Forms (CRWMS M&O 1999a) and Technical Work Plan For: Department of Energy Spent Nuclear Fuel Work Packages (CRWMS M&O 2000d). This calculation contains no electronic data applicable to any electronic data management system.

  4. Nevada Test Site Waste Acceptance Criteria (NTSWAC)

    Energy Technology Data Exchange (ETDEWEB)

    NNSA/NSO Waste Management Project

    2008-06-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive (LLW) and LLW Mixed Waste (MW) for disposal.

  5. Nevada Test Site Waste Acceptance Criteria (NTSWAC)

    International Nuclear Information System (INIS)

    NNSA/NSO Waste Management Project

    2008-01-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive (LLW) and LLW Mixed Waste (MW) for disposal

  6. Hanford Site Solid Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-17

    This manual defines the Hanford Site radioactive, hazardous, and sanitary solid waste acceptance criteria. Criteria in the manual represent a guide for meeting state and federal regulations; DOE Orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to acceptance of radioactive and hazardous solid waste at the Hanford Site. It is not the intent of this manual to be all inclusive of the regulations; rather, it is intended that the manual provide the waste generator with only the requirements that waste must meet in order to be accepted at Hanford Site TSD facilities.

  7. Hanford Site Solid Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    1993-01-01

    This manual defines the Hanford Site radioactive, hazardous, and sanitary solid waste acceptance criteria. Criteria in the manual represent a guide for meeting state and federal regulations; DOE Orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to acceptance of radioactive and hazardous solid waste at the Hanford Site. It is not the intent of this manual to be all inclusive of the regulations; rather, it is intended that the manual provide the waste generator with only the requirements that waste must meet in order to be accepted at Hanford Site TSD facilities

  8. NEVADA TEST SITE WASTE ACCEPTANCE CRITERIA

    International Nuclear Information System (INIS)

    U.S. DEPARTMENT OF ENERGY, NATIONAL NUCLEAR SECURITY ADMINISTRATION, NEVADA SITE OFFICE

    2005-01-01

    This document establishes the U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive and mixed waste for disposal. Mixed waste generated within the State of Nevada by NNSA/NSO activities is accepted for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Site for storage or disposal

  9. Hanford Site solid waste acceptance criteria

    International Nuclear Information System (INIS)

    Ellefson, M.D.

    1998-01-01

    Order 5820.2A requires that each treatment, storage, and/or disposal facility (referred to in this document as TSD unit) that manages low-level or transuranic waste (including mixed waste and TSCA PCB waste) maintain waste acceptance criteria. These criteria must address the various requirements to operate the TSD unit in compliance with applicable safety and environmental requirements. This document sets forth the baseline criteria for acceptance of radioactive waste at TSD units operated by WMH. The criteria for each TSD unit have been established to ensure that waste accepted can be managed in a manner that is within the operating requirements of the unit, including environmental regulations, DOE Orders, permits, technical safety requirements, waste analysis plans, performance assessments, and other applicable requirements. Acceptance criteria apply to the following TSD units: the Low-Level Burial Grounds (LLBG) including both the nonregulated portions of the LLBG and trenches 31 and 34 of the 218-W-5 Burial Ground for mixed waste disposal; Central Waste Complex (CWC); Waste Receiving and Processing Facility (WRAP); and T Plant Complex. Waste from all generators, both from the Hanford Site and from offsite facilities, must comply with these criteria. Exceptions can be granted as provided in Section 1.6. Specific waste streams could have additional requirements based on the 1901 identified TSD pathway. These requirements are communicated in the Waste Specification Records (WSRds). The Hanford Site manages nonradioactive waste through direct shipments to offsite contractors. The waste acceptance requirements of the offsite TSD facility must be met for these nonradioactive wastes. This document does not address the acceptance requirements of these offsite facilities

  10. Nevada Test Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    U. S. Department of Energy, National Nuclear Security Administration Nevada Site Office

    2005-01-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO) waste acceptance criteria (WAC). The WAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive (LLW) and mixed waste (MW) for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex (RWMC) for storage or disposal

  11. Application of trial risk acceptance criteria

    International Nuclear Information System (INIS)

    Johnson, D.H.; Kastenberg, W.E.; Okrent, D.

    1982-01-01

    The objective of this paper is to investigate some of the implications inherent in the application of various proposed sets of risk acceptance criteria. A power-law model of risk aversion is utilized to estimate the equivalent number of individual deaths and is treated parametrically. The implications of ALARA requirements for cost-effective improvements are also illustrated. The risks assessed for various technological endeavors, as well as some estimated natural background risks, are compared to the trial criteria

  12. Acceptance criteria for radioactive waste deposition

    International Nuclear Information System (INIS)

    Rzyski, B.M.

    1989-01-01

    The disposal of low-and intermediate level radioactive waste in either shallow ground or rock cavities must be subjected to special guidelines which are used by national authorities and implementing bodies when establishing and regulating respositories. These informations are given by the acceptance criteria and will depend on specific site conditions and optmized procedures. (author) [pt

  13. Environmental Restoration Disposal Facility Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    Dronen, V.R.

    1998-06-01

    The Hanford Site is operated by the U. S. Department of Energy (DOE) with a primary mission of environmental cleanup and restoration. The Environmental Restoration Disposal Facility (ERDF) is an integral part of the DOE environmental restoration effort at the Hanford Site. The purpose of this document is to establish the ERDF waste acceptance criteria for disposal of materials resulting from Hanford Site cleanup activities. Definition of and compliance with the requirements of this document will enable implementation of appropriate measures to protect human health and the environment, ensure the integrity of the ERDF liner system, facilitate efficient use of the available space in the ERDF, and comply with applicable environmental regulations and DOE orders. To serve this purpose, the document defines responsibilities, identifies the waste acceptance process, and provides the primary acceptance criteria and regulatory citations to guide ERDF users. The information contained in this document is not intended to repeat or summarize the contents of all applicable regulations

  14. Nevada National Security Site Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2010-09-03

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NNSSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NNSS Area 3 and Area 5 Radioactive Waste Management Complex for disposal. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project at (702) 295-7063 or fax to (702) 295-1153.

  15. Nevada National Security Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2010-01-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NNSSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NNSS Area 3 and Area 5 Radioactive Waste Management Complex for disposal. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project at (702) 295-7063 or fax to (702) 295-1153.

  16. Nevada National Security Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2011-01-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NNSSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NNSS Area 3 and Area 5 Radioactive Waste Management Complex for disposal. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project at (702) 295-7063 or fax to (702) 295-1153.

  17. Nevada National Security Site Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2013-06-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO), Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept the following: • DOE hazardous and non-hazardous non-radioactive classified waste • DOE low-level radioactive waste (LLW) • DOE mixed low-level waste (MLLW) • U.S. Department of Defense (DOD) classified waste The LLW and MLLW listed above may also be classified waste. Classified waste is the only waste accepted for disposal that may be non-radioactive and shall be required to meet the waste acceptance criteria for radioactive waste as specified in this document. Classified waste may be sent to the NNSS as classified matter. Section 3.1.18 provides the requirements that must be met for permanent burial of classified matter. The NNSA/NFO and support contractors are available to assist the generator in understanding or interpreting this document. For assistance, please call the NNSA/NFO Environmental Management Operations (EMO) at (702) 295-7063, and the call will be directed to the appropriate contact.

  18. Nevada National Security Site Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2012-02-28

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO), Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept DOE non-radioactive classified waste, DOE non-radioactive hazardous classified waste, DOE low-level radioactive waste (LLW), DOE mixed low-level waste (MLLW), and U.S. Department of Defense (DOD) classified waste for permanent disposal. Classified waste is the only waste accepted for disposal that may be non-radioactive and will be required to meet the waste acceptance criteria for radioactive waste as specified in this document. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project (WMP) at (702) 295-7063, and your call will be directed to the appropriate contact.

  19. Nevada National Security Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2012-01-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office (NNSA/NSO), Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept DOE non-radioactive classified waste, DOE non-radioactive hazardous classified waste, DOE low-level radioactive waste (LLW), DOE mixed low-level waste (MLLW), and U.S. Department of Defense (DOD) classified waste for permanent disposal. Classified waste is the only waste accepted for disposal that may be non-radioactive and will be required to meet the waste acceptance criteria for radioactive waste as specified in this document. The NNSA/NSO and support contractors are available to assist you in understanding or interpreting this document. For assistance, please call the NNSA/NSO Waste Management Project (WMP) at (702) 295-7063, and your call will be directed to the appropriate contact.

  20. Nevada National Security Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2013-01-01

    This document establishes the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office (NNSA/NFO), Nevada National Security Site Waste Acceptance Criteria (NNSSWAC). The NNSSWAC provides the requirements, terms, and conditions under which the Nevada National Security Site (NNSS) will accept the following: DOE hazardous and non-hazardous non-radioactive classified waste; DOE low-level radioactive waste (LLW); DOE mixed low-level waste (MLLW); and, U.S. Department of Defense (DOD) classified waste. The LLW and MLLW listed above may also be classified waste. Classified waste is the only waste accepted for disposal that may be non-radioactive and shall be required to meet the waste acceptance criteria for radioactive waste as specified in this document. Classified waste may be sent to the NNSS as classified matter. Section 3.1.18 provides the requirements that must be met for permanent burial of classified matter. The NNSA/NFO and support contractors are available to assist the generator in understanding or interpreting this document. For assistance, please call the NNSA/NFO Environmental Management Operations (EMO) at (702) 295-7063, and the call will be directed to the appropriate contact.

  1. Hanford Site solid waste acceptance criteria

    International Nuclear Information System (INIS)

    Willis, N.P.; Triner, G.C.

    1991-09-01

    Westinghouse Hanford Company manages the Hanford Site solid waste treatment, storage, and disposal facilities for the US Department of Energy Field Office, Richland under contract DE-AC06-87RL10930. These facilities include radioactive solid waste disposal sites, radioactive solid waste storage areas and hazardous waste treatment, storage, and/or disposal facilities. This manual defines the criteria that must be met by waste generators for solid waste to be accepted by Westinghouse Hanford Company for treatment, storage and/or disposal facilities. It is to be used by all waste generators preparing radioactive solid waste for storage or disposal at the Hanford Site facilities and for all Hanford Site generators of hazardous waste. This manual is also intended for use by Westinghouse Hanford Company solid waste technical staff involved with approval and acceptance of solid waste. The criteria in this manual represent a compilation of state and federal regulations; US Department of Energy orders; Hanford Site requirements; and other rules, regulations, guidelines, and standards as they apply to management of solid waste. Where appropriate, these requirements are included in the manual by reference. It is the intent of this manual to provide guidance to the waste generator in meeting the applicable requirements

  2. Structural acceptance criteria Remote Handling Building Tritium Extraction Facility

    Energy Technology Data Exchange (ETDEWEB)

    Mertz, G.

    1999-12-16

    This structural acceptance criteria contains the requirements for the structural analysis and design of the Remote Handling Building (RHB) in the Tritium Extraction Facility (TEF). The purpose of this acceptance criteria is to identify the specific criteria and methods that will ensure a structurally robust building that will safely perform its intended function and comply with the applicable Department of Energy (DOE) structural requirements.

  3. Structural acceptance criteria Remote Handling Building Tritium Extraction Facility

    International Nuclear Information System (INIS)

    Mertz, G.

    1999-01-01

    This structural acceptance criteria contains the requirements for the structural analysis and design of the Remote Handling Building (RHB) in the Tritium Extraction Facility (TEF). The purpose of this acceptance criteria is to identify the specific criteria and methods that will ensure a structurally robust building that will safely perform its intended function and comply with the applicable Department of Energy (DOE) structural requirements

  4. Nevada Test Site Waste Acceptance Criteria, December 2000

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-12-01

    This document establishes the US Department of Energy, Nevada Operations Office waste acceptance criteria. The waste acceptance criteria provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive waste and mixed waste for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Sites for storage or disposal.

  5. Nevada Test Site Waste Acceptance Criteria, December 2000

    International Nuclear Information System (INIS)

    2000-01-01

    This document establishes the US Department of Energy, Nevada Operations Office waste acceptance criteria. The waste acceptance criteria provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive waste and mixed waste for disposal. It includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the Nevada Test Site Area 3 and Area 5 Radioactive Waste Management Sites for storage or disposal

  6. Nevada Test Site Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    U.S. Department of Energy, Nevada Operations Office, Waste Acceptance Criteria

    1999-01-01

    This document provides the requirements, terms, and conditions under which the Nevada Test Site will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the Nevada Test Site

  7. Nevada test site waste acceptance criteria

    International Nuclear Information System (INIS)

    1996-01-01

    This document provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document

  8. Nevada test site waste acceptance criteria

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    This document provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document.

  9. Inelastic analysis acceptance criteria for radioactive material transportation containers

    International Nuclear Information System (INIS)

    Ammerman, D.J.; Ludwigsen, J.S.

    1993-01-01

    The design criteria currently used in the design of radioactive material (RAM) transportation containers are taken from the ASME Boiler and Pressure Vessel Code (ASME, 1992). These load-based criteria are ideally suited for pressure vessels where the loading is quasistatic and all stresses are in equilibrium with externally applied loads. For impact events, the use of load-based criteria is less supportable. Impact events tend to be energy controlled, and thus, energy-based acceptance criteria would appear to be more appropriate. Determination of an ideal design criteria depends on what behavior is desired. Currently there is not a design criteria for inelastic analysis for RAM nation packages that is accepted by the regulatory agencies. This lack of acceptance criteria is one of the major factors in limiting the use of inelastic analysis. In this paper inelastic analysis acceptance criteria based on stress and strain-energy density will be compared for two stainless steel test units subjected to impacts onto an unyielding target. Two different material models are considered for the inelastic analysis, a bilinear fit of the stress-strain curve and a power law hardening model that very closely follows the stress-strain curve. It is the purpose of this paper to stimulate discussion and research into the area of strain-energy density based inelastic analysis acceptance criteria

  10. Risk acceptance criteria of the Nuclear Regulatory Authority

    International Nuclear Information System (INIS)

    Felizia, Eduardo R.

    2005-01-01

    This report describes some of the regulatory and control functions legally conferred upon the Argentine Nuclear Regulatory Authority concerning radiological risks, as well as a critical analysis of the radiological risk acceptance criteria contained in the Argentine regulatory system. A summary of the application of regulatory standards AR 3.1.3. - 'Radiological criteria related to accidents in nuclear power reactors' and AR 4.1.3. - 'Radiological criteria related to accidents in research reactors' to concrete cases is made, while the favourable and unfavourable aspects of the risk acceptance criteria are discussed. The conclusion is that the Argentine regulatory system contains adequate radiological risk acceptance criteria, that the latter are consistent with the radiological protection principles applicable to man and that, for the moment, there is no need to perform any modifications that would broaden the conceptual framework on which such criteria are based. (author) [es

  11. Acceptance criteria considerations for miscellaneous wastes

    International Nuclear Information System (INIS)

    Irvine, A.R.; Forsberg, C.W.

    1987-01-01

    EPA standards set forth limitations regarding releases to the accessible environment adjacent to a geologic repository. The NRC criteria pertaining to waste form and engineered barrier performance place certain restrictions on the physical and chemical nature of the waste form and require substantially complete confinement of radioactivity until the high-heat-production period is past. After this period, the annual release of radionuclides from the waste package is normally limited to 1 part in 100,000 of the amounts calculated to be present at 1000-y decay. The regulation permits deviation from these criteria in exceptional circumstances. One such circumstance might be the absence of a significant perturbation in temperature around the stored waste. The lack of significant heat release will eliminate the hydrologic driving force for dispersal of radionuclides. Exceptional circumstances which potentially could justify a less stringent long-term release criterion are: small quantity of radioactivity, the nature of the radioactive species, and the nature of the geology in which the waste is to be emplaced. Because the MW after a suitable decay period have low heat release rates per unit volume, they apparently could be so emplaced in a repository that there would be no compelling need, according to the reasoning presented in 10 CFR 60, for a 1000-y container. Regarding attainment of the specified long-term release rate criterion, neither the solubility limits for the various waste forms nor the conductance of potential migration barriers are currently adequately characterized. The relatively small total heat generation rate for the MW in combination with the usual low volumetric heat generation rate apparently will allow application of migration barriers in a low temperature environment where barrier performance would be expected to be unchanged with time

  12. Heat exchanger, head and shell acceptance criteria

    International Nuclear Information System (INIS)

    Lam, P.S.; Sindelar, R.L.

    1992-09-01

    Instability of postulated flaws in the head component of the heat exchanger could not produce a large break, equivalent to a DEGB in the PWS piping, due to the configuration of the head and restraint provided by the staybolts. Rather, leakage from throughwall flaws in the head would increase with flaw length with finite leakage areas that are bounded by a post-instability flaw configuration. Postulated flaws at instability in the shell of the heat exchanger or in the cooling water nozzles could produce a large break in the Cooling Water System (CWS) pressure boundary. An initial analysis of flaw stability for postulated flaws in the heat exchanger head was performed in January 1992. This present report updates that analysis and, additionally, provides acceptable flaw configurations to maintain defined structural or safety margins against flaw instability of the external pressure boundary components of the heat exchanger, namely the head, shell, and cooling water nozzles. Structural and flaw stability analyses of the heat exchanger tubes, the internal pressure boundary of the heat exchangers or interface boundary between the PWS and CWS, were previously completed in February 1992 as part of the heat exchanger restart evaluation and are not covered in this report

  13. Design Criteria for Achieving Acceptable Indoor Radon Concentration

    DEFF Research Database (Denmark)

    Rasmussen, Torben Valdbjørn

    2016-01-01

    Design criteria for achieving an acceptable indoor radon concentration are presented in this paper. The paper suggests three design criteria. These criteria have to be considered at the early stage of the building design phase to meet the latest recommendations from the World Health Organization...... in most countries. The three design criteria are; first, establishing a radon barrier facing the ground; second, lowering the air pressure in the lower zone of the slab on ground facing downwards; third, diluting the indoor air with outdoor air. The first two criteria can prevent radon from infiltrating...... from the ground, and the third criteria can dilute the indoor air. By combining these three criteria, the indoor radon concentration can be lowered achieving an acceptable level. In addition, a cheap and reliable method for measuring the radon concentration in the indoor air is described. The provision...

  14. Reality check on girth weld defect acceptance criteria

    Energy Technology Data Exchange (ETDEWEB)

    Brust, Bud; Kalyanam, Suresh; Shim, Do-Jun; Wilkowski, Gery [Engineering Mechanics Corporation of Columbus, Columbus, OH, (United States)

    2010-07-01

    Girth weld defect tolerance criteria for pipeline construction has evolved with time. Recently, ERPG recommended a new Tier 2 girth weld defect acceptance criterion. This paper described the new development on girth weld defect acceptance criteria. The inherent conservatisms of alternative girth weld defect acceptance criteria from the 2007 API 1104 Appendix A, CSA Z662 Appendix K, are compared to those from the proposed EPRG Tier 2 criteria. It is found that the API and CSA codes have the same empirical limit-load criteria. As well, there are conservatisms in the proposed EPRG Tier 2. The results showed that there are various reasons why large amounts of conservatism in the allowable flaw lengths in the CSA Appendix K,2007 API 1104 Appendix A, and proposed EPRG Tier 2 girth weld defect criterion exist. Small conservatisms on failure stress can result in large conservatisms in flaw size.

  15. Criteria for accepting piping vibrations measured during FFTF plant startup

    International Nuclear Information System (INIS)

    Huang, S.N.

    1981-03-01

    Piping in the Fast Flux Test Facility is subjected to low-amplitude, high cycle vibration over the plant lifetime. Excitation sources include the mechanical vibration induced by main centrifugal pumps, auxiliary reciprocating pumps, EM pumps and possible flow oscillations. Vibration acceptance criteria must be established which will prevent excessive pipe and support fatigue damage when satified. This paper describes the preparation of such criteria against pipe failure used for acceptance testing of the Fast Flux Test Facility main heat transport piping

  16. Risk Acceptance Criteria and/or Decision optimization

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    1996-01-01

    Acceptance criteria applied in practical risk analysis are recapitulated including the concept of rist profile. Modelling of risk profiles is illustrated on the basis of compound Poisson process models. The current practice of authoritative acceptance criteria formulation is discussed from...... a decision theoretical point of view. It is argued that the phenomenon of risk aversion rather than being of concern to the authority should be of concern to the owner. Finally it is discussed whether there is an ethical problem when formally capitalising human lives with a positive interest rate. Keywords......: Risk acceptance, Risk profile, Compound Poisson model for risk profile, Capitalization of human life, Risk aversion....

  17. Idaho CERCLA Disposal Facility Complex Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    W. Mahlon Heileson

    2006-10-01

    The Idaho Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) Disposal Facility (ICDF) has been designed to accept CERCLA waste generated within the Idaho National Laboratory. Hazardous, mixed, low-level, and Toxic Substance Control Act waste will be accepted for disposal at the ICDF. The purpose of this document is to provide criteria for the quantities of radioactive and/or hazardous constituents allowable in waste streams designated for disposal at ICDF. This ICDF Complex Waste Acceptance Criteria is divided into four section: (1) ICDF Complex; (2) Landfill; (3) Evaporation Pond: and (4) Staging, Storage, Sizing, and Treatment Facility (SSSTF). The ICDF Complex section contains the compliance details, which are the same for all areas of the ICDF. Corresponding sections contain details specific to the landfill, evaporation pond, and the SSSTF. This document specifies chemical and radiological constituent acceptance criteria for waste that will be disposed of at ICDF. Compliance with the requirements of this document ensures protection of human health and the environment, including the Snake River Plain Aquifer. Waste placed in the ICDF landfill and evaporation pond must not cause groundwater in the Snake River Plain Aquifer to exceed maximum contaminant levels, a hazard index of 1, or 10-4 cumulative risk levels. The defined waste acceptance criteria concentrations are compared to the design inventory concentrations. The purpose of this comparison is to show that there is an acceptable uncertainty margin based on the actual constituent concentrations anticipated for disposal at the ICDF. Implementation of this Waste Acceptance Criteria document will ensure compliance with the Final Report of Decision for the Idaho Nuclear Technology and Engineering Center, Operable Unit 3-13. For waste to be received, it must meet the waste acceptance criteria for the specific disposal/treatment unit (on-Site or off-Site) for which it is destined.

  18. Radwaste characteristics and Disposal Facility Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    Sung, Suk Hyun; Jeong, Yi Yeong; Kim, Ki Hong

    2008-01-01

    The purpose of Radioactive Waste Acceptance Criteria (WAC) is to verify a radioactive waste compliance with radioactive disposal facility requirements in order to maintain a disposal facility's performance objectives and to ensure its safety. To develop WAC which is conformable with domestic disposal site conditions, we furthermore analysed the WAC of foreign disposal sites similar to the Kyung-Ju disposal site and the characteristics of various wastes which are being generated from Korea nuclear facilities. Radioactive WAC was developed in the technical cooperation with the Korea Atomic Energy Research Institute in consideration of characteristics of the wastes which are being generated from various facilities, waste generators' opinions and other conditions. The established criteria was also discussed and verified at an advisory committee which was comprised of some experts from universities, institutes and the industry. So radioactive WAC was developed to accept all wastes which are being generated from various nuclear facilities as much as possible, ensuring the safety of a disposal facility. But this developed waste acceptance criteria is not a criteria to accept all the present wastes generated from various nuclear facilities, so waste generators must seek an alternative treatment method for wastes which were not worth disposing of, and then they must treat the wastes more to be acceptable at a disposal site. The radioactive disposal facility WAC will continuously complement certain criteria related to a disposal concentration limit for individual radionuclide in order to ensure a long-term safety.

  19. Anticipating Potential Waste Acceptance Criteria for Defense Spent Nuclear Fuel

    International Nuclear Information System (INIS)

    Rechard, R.P.; Lord, M.E.; Stockman, C.T.; McCurley, R.D.

    1997-01-01

    The Office of Environmental Management of the U.S. Department of Energy is responsible for the safe management and disposal of DOE owned defense spent nuclear fuel and high level waste (DSNF/DHLW). A desirable option, direct disposal of the waste in the potential repository at Yucca Mountain, depends on the final waste acceptance criteria, which will be set by DOE's Office of Civilian Radioactive Waste Management (OCRWM). However, evolving regulations make it difficult to determine what the final acceptance criteria will be. A method of anticipating waste acceptance criteria is to gain an understanding of the DOE owned waste types and their behavior in a disposal system through a performance assessment and contrast such behavior with characteristics of commercial spent fuel. Preliminary results from such an analysis indicate that releases of 99Tc and 237Np from commercial spent fuel exceed those of the DSNF/DHLW; thus, if commercial spent fuel can meet the waste acceptance criteria, then DSNF can also meet the criteria. In large part, these results are caused by the small percentage of total activity of the DSNF in the repository (1.5%) and regulatory mass (4%), and also because commercial fuel cladding was assumed to provide no protection

  20. HWVP compliance with the Hanford site solid waste acceptance criteria

    International Nuclear Information System (INIS)

    Bromm, R.; Ornelas, J.; Fundingsland, S.; Shah, K.

    1993-01-01

    In order to ensure that the Hanford Waste Vitrification Project (HWVP) will meet solid waste acceptance criteria, a review of the criteria was performed. The primary purpose of the study was to evaluate the modifications that will be required to bring the HWVP into compliance for secondary waste which will be generated during normal operations of the facility. To accomplish this objective, the current HWVP design was evaluated based on the criteria established. Once the non-compliance areas and potentially non-compliance areas were identified, alternative plant design modifications were proposed. This paper summarizes the results and recommendations of that study

  1. Acceptability criteria for final underground disposal of radioactive waste

    International Nuclear Information System (INIS)

    Sousselier, Y.

    1984-01-01

    Specialists now generally agree that the underground disposal of suitably immobilized radioactive waste offers a means of attaining the basic objective of ensuring the immediate and long-term protection of man and the environment throughout the requisite period of time and in all foreseeable circumstances. Criteria of a more general as well as a more specific nature are practical means through which this basic protection objective can be reached. These criteria, which need not necessarily be quantified, enable the authorities to gauge the acceptability of a given project and provide those responsible for waste management with a basis for making decisions. In short, these principles constitute the framework of a suitably safety-oriented waste management policy. The more general criteria correspond to the protection objectives established by the national authorities on the basis of principles and recommendations formulated by international organizations, in particular the ICRP and the IAEA. They apply to any underground disposal system considered as a whole. The more specific criteria provide a means of evaluating the degree to which the various components of the disposal system meet the general criteria. They must also take account of the interaction between these components. As the ultimate aim is the overall safety of the disposal system, individual components can be adjusted to compensate for the performance of others with respect to the criteria. This is the approach adopted by the international bodies and national authorities in developing acceptability criteria for the final underground radioactive disposal systems to be used during the operational and post-operational phases respectively. The main criteria are reviewed and an attempt is made to assess the importance of the specific criteria according to the different types of disposal systems. (author)

  2. A Study on the Acceptance Criteria for DTrip Frequency

    International Nuclear Information System (INIS)

    Kim, Kil Yoo; Lee, Hyun Woo; Jae, Moo Sung

    2011-01-01

    Many risk informed regulation and applications (RIR and A) are approved, and more RIR and A will be actively applied in Korea. The acceptance criteria for the RIR and A have been DCDF, and DLERF. However, in the economical point of view, the change of the reactor trip frequency (hereafter, it is called Dtrip) are important element to monitor in the RIR and A. A reactor trip causes a huge economical loss, and causes a bad reputation in the social acceptance which causes eventually a social cost, and could induce a safety problem by giving a severe stress on the operators. Usually, the chief managers of nuclear power plants are reluctant to increase the trip frequency by a RIR and A, even though the RIR and A could bring an economical benefit, and could not threaten the safety. Because, if a reactor trip occurs, it would be reflected in his performance assessment. Therefore, it is necessary to set up an acceptance criteria for Dtrip in the RIR and A without depending on the personal preference of the chief manager. This paper introduces the acceptance criteria for Dtrip in the RIR and A

  3. MCO combustible gas management leak test acceptance criteria; TOPICAL

    International Nuclear Information System (INIS)

    SHERRELL, D.L.

    1999-01-01

    Existing leak test acceptance criteria for mechanically sealed and weld sealed multi-canister overpacks (MCO) were evaluated to ensure that MCOs can be handled and stored in stagnant air without compromising the Spent Nuclear Fuel Project's overall strategy to prevent accumulation of combustible gas mixtures within MCO's or within their surroundings. The document concludes that the integrated leak test acceptance criteria for mechanically sealed and weld sealed MCOs (1 x 10(sup -5) std cc/sec and 1 x 10(sup -7) std cc/sec, respectively) are adequate to meet all current and foreseeable needs of the project, including capability to demonstrate compliance with the NFPA 60 Paragraph 3-3 requirement to maintain hydrogen concentrations[within the air atmosphere CSB tubes] t or below 1 vol% (i.e., at or below 25% of the LFL)

  4. Procedures and acceptance criteria for PAS-1 cask inspections

    International Nuclear Information System (INIS)

    Mercado, J.E.

    1998-01-01

    The procedures and acceptance criteria that comprise this document were prepared to support a one-time test to certify two PAS-1 casks in accordance with US Department of Energy Certificate of Compliance US A/9184/B(U), which was issued in 1998. The specific inspections addressed in this document are the visual weld inspection and a dimensional inspection of the primary containment vessel

  5. Waste-acceptance criteria for greater confinement disposal

    International Nuclear Information System (INIS)

    Gilbert, T.L.; Meshkov, N.K.

    1987-01-01

    A methodology for establishing waste-acceptance criteria based on quantitative performance factors that characterize the confinement capabilities of a waste disposal site and facility has been developed. The methodology starts from the basic objective of protecting public health and safety by providing assurance that disposal of the waste will not result in a radiation dose to any member of the general public, in either the short or long term, in excess of an established basic dose limit. The method is based on an explicit, straight-forward, and quantitative relationship among individual risk, confinement capabilities, and waste characteristics. A key aspect of the methodology is introduction of a confinement factor that characterizes the overall confinement capability of a particular facility and can be used for quantitative assessments of the performance of different disposal sites and facilities, as well as for establishing site-specific waste acceptance criteria. Confinement factors are derived by means of site-specific pathway analyses. They make possible a direct and simple conversion of a basic dose limit into waste-acceptance criteria, specified as concentration limits on radionuclides in the waste streams and expressed in quantitative form as a function of parameters that characterize the site, facility design, waste containers, and waste form. Waste acceptance criteria can be represented visually as activity/time plots for various waste streams. These plots show the concentrations of radionuclides in a waste stream as a function of time and permit a visual, quantitative assessment of long-term performance, relative risks from different radionuclides in the waste stream, and contributions from ingrowth. 13 references, 7 figures

  6. Waste-acceptance criteria for greater-confinement disposal

    International Nuclear Information System (INIS)

    Gilbert, T.L.; Meshkov, N.K.

    1986-01-01

    A methodology for establishing waste-acceptance criteria based on quantitative performance factors that characterize the confinement capabilities of a waste-disposal site and facility has been developed. The methodology starts from the basic objective of protecting public health and safety by providing assurance that dispsoal of the waste will not result in a radiation dose to any member of the general public, in either the short or long term, in excess of an established basic dose limit. The method is based on an explicit, straightforward, and quantitative relationship among individual risk, confinement capabilities, and waste characteristics. A key aspect of the methodology is the introduction of a confinement factor that characterizes the overall confinement capability of a particular facility and can be used for quantitative assessments of the performance of different disposal sites and facilities, as well as for establishing site-specific waste-acceptance criteria. Confinement factors are derived by means of site-specific pathway analyses. They make possible a direct and simple conversion of a basic dose limit into waste-acceptance criteria, specified as concentration limits on radionuclides in the waste streams and expressed in quantitative form as a function of parameters that characterize the site, facility design, waste containers, and waste form. Waste-acceptance criteria can be represented visually as activity/time plots for various waste streams. These plots show the concentrations of radionuclides in a waste stream as a function of time and permit a visual, quantitative assessment of long-term performance, relative risks from different radionuclides in the waste stream, and contributions from ingrowth. 13 refs

  7. Waste acceptance criteria study: Volume 2, Appendixes: Final report

    International Nuclear Information System (INIS)

    Johnson, E.R.; McLeod, N.B.; McBride, J.A.

    1988-09-01

    These appendices to the report on Waste Acceptance Criteria have been published as a separate volume for the convenience of the reader. They consist of the text of the 10CFR961 Contract for disposal of spent fuel, estimates of the cost (savings) to the DOE system of accepting different forms of spent fuel, estimates of costs of acceptance testing/inspection of spent fuel, illustrative specifications and procedures, and the resolution of comments received on a preliminary draft of the report. These estimates of costs contained herein preliminary and are intended only to demonstrate the trends in costs, the order of magnitude involved, and the methodology used to develop the costs. The illustrative specifications and procedures included herein have been developed for the purpose of providing a starting point for the development of a consensus on such matters between utilities and DOE

  8. Establishing seismic design criteria to achieve an acceptable seismic margin

    International Nuclear Information System (INIS)

    Kennedy, R.P.

    1997-01-01

    In order to develop a risk based seismic design criteria the following four issues must be addressed: (1) What target annual probability of seismic induced unacceptable performance is acceptable? (2). What minimum seismic margin is acceptable? (3) Given the decisions made under Issues 1 and 2, at what annual frequency of exceedance should the Safe Shutdown Earthquake ground motion be defined? (4) What seismic design criteria should be established to reasonably achieve the seismic margin defined under Issue 2? The first issue is purely a policy decision and is not addressed in this paper. Each of the other three issues are addressed. Issues 2 and 3 are integrally tied together so that a very large number of possible combinations of responses to these two issues can be used to achieve the target goal defined under Issue 1. Section 2 lays out a combined approach to these two issues and presents three potentially attractive combined resolutions of these two issues which reasonably achieves the target goal. The remainder of the paper discusses an approach which can be used to develop seismic design criteria aimed at achieving the desired seismic margin defined in resolution of Issue 2. Suggestions for revising existing seismic design criteria to more consistently achieve the desired seismic margin are presented

  9. Criteria for risk acceptance: a health physicist's view

    International Nuclear Information System (INIS)

    Hull, A. P.

    1977-01-01

    While energy need (or demand) and the risks of energy production and use may be objectively quantified, risk acceptance embodies a subjective element of preferences and values. Yet, as demonstrated by the nuclear controversy in the United States, public acceptance is essential to the beneficial uses of radiation. The statement of the objectives and purposes of the Health Physics Society and our application of it are proposed as offering useful criteria for risk acceptance. The principle of comparing risk with a number of those regularly accepted in everyday life is emphasized. On this basis, it is concluded that the expenditures to attain currently applicable or proposed 'as low as practicable' (or 'as low as readily achievable') levels for the nuclear fuel cycle are disproportionate to those addressed to other sources of general public exposure to radiation. They are also disproportionate compared to those addressed to a variety of public health risks. It is suggested that sensible priorities for radiation and public health protection might be achieved by the application of a de minimus negligible (but nonzero) level of probable risk. (Research supported by the U.S. Energy Research and Development Administration.)

  10. Acceptance criteria for the low enriched uranium reform amendments

    International Nuclear Information System (INIS)

    Emeigh, C.W.; Gundersen, G.E.; Withee, C.J.

    1984-05-01

    Revisions have been made to the material control and accounting requirements for NRC licensees authorized to possess and use more than one effective kilogram of special nuclear material of low strategic significance to have material control and accounting systems able to (1) confirm the presence of special nuclear material, (2) resolve indications of missing material, and (3) aid in the investigation and recovery of missing material. This document presents criteria that can be used to aid in judging the acceptability of licensee plans that would be submitted to the NRC for implementing these capabilities. General performance objectives, system capabilities, and recordkeeping are addressed

  11. Waste acceptance criteria for the Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    1996-04-01

    The Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria (WAC), DOE/WIPP-069, was initially developed by a U.S. Department of Energy (DOE) Steering Committee to provide performance requirements to ensure public health and safety as well as the safe handling of transuranic (TRU) waste at the WIPP. This revision updates the criteria and requirements of previous revisions and deletes those which were applicable only to the test phase. The criteria and requirements in this document must be met by participating DOE TRU Waste Generator/Storage Sites (Sites) prior to shipping contact-handled (CH) and remote-handled (RH) TRU waste forms to the WIPP. The WIPP Project will comply with applicable federal and state regulations and requirements, including those in Titles 10, 40, and 49 of the Code of Federal Regulations (CFR). The WAC, DOE/WIPP-069, serves as the primary directive for assuring the safe handling, transportation, and disposal of TRU wastes in the WIPP and for the certification of these wastes. The WAC identifies strict requirements that must be met by participating Sites before these TRU wastes may be shipped for disposal in the WIPP facility. These criteria and requirements will be reviewed and revised as appropriate, based on new technical or regulatory requirements. The WAC is a controlled document. Revised/changed pages will be supplied to all holders of controlled copies

  12. Automated Transportation Management System (ATMS) V2.0 logistics module PBI acceptance criteria

    International Nuclear Information System (INIS)

    Weidert, R.S.

    1995-01-01

    This document defines the acceptance criteria for the Automated Transportation Management System V2.0 Logistics Module Performance Based Incentive (PBI). This acceptance criteria will be the primary basis for the generation of acceptance test procedures. The purpose of this document is to define the minimum criteria that must be fulfilled to guarantee acceptance of the Logistics Module

  13. Synthetic seismic acceleration time-histories and their acceptance criteria

    International Nuclear Information System (INIS)

    Xu Hong

    1996-01-01

    In seismic dynamic response analysis of structures and equipment, time-history analysis is now widely used. The 3-D seismic acceleration time-histories or 3-D seismic displacement time-histories are required in the 3-D seismic dynamic response analysis as the seismic excitation input data. Because of the lack of actual acceleration time-histories for the field where the structures or equipment are installed, the general practice is to use the synthetic seismic acceleration time-histories, which are derived from the design seismic response spectra of the field, as the seismic excitation input data. However, from one specified design response spectrum indefinite solutions of acceleration time-histories can be derived depending on the values of the input parameters. Not all the derived synthetic time-histories can be used as seismic excitation input data. Only those which meet the acceptance criteria can be used. The factors (input parameters), which will affect the time-history solution from a specified seismic response spectrum, and the acceptance criteria are discussed

  14. Managing Hanford Site solid waste through strict acceptance criteria

    International Nuclear Information System (INIS)

    Jasen, W.G.; Pierce, R.D.; Willis, N.P.

    1993-02-01

    Various types of waste have been generated during the 50-year history of the Hanford Site. Regulatory changes in the last 20 years have provided the emphasis for better management of these wastes. Interpretations of the Atomic Energy Act of 1954 (AEA) and the Resource Conservation and Recovery Act of 1976 (RCRA) have led to the definition of a group of wastes called radioactive mixed wastes (RMW). As a result of the radioactive and hazardous properties of these wastes, strict management programs have been implemented for the management of these wastes. Solid waste management is accomplished through a systems performance approach to waste management that used best-demonstrated available technology (BDAT) and best management practices. The solid waste program at the Hanford Site strives to integrate all aspects of management relative to the treatment, storage and disposal (TSD) of solid waste. Often there are many competing and important needs. It is a difficult task to balance these needs in a manner that is both equitable and productive. Management science is used to help the process of making decisions. Tools used to support the decision making process include five-year planning, cost estimating, resource allocation, performance assessment, waste volume forecasts, input/output models, and waste acceptance criteria. The purpose of this document is to describe how one of these tools, waste acceptance criteria, has helped the Hanford Site manage solid wastes

  15. Sample acceptance time criteria, electronic issue and alloimmunisation in thalassaemia.

    Science.gov (United States)

    Trompeter, S; Baxter, L; McBrearty, M; Zatkya, E; Porter, J

    2015-12-01

    To determine the safety of a 1-week acceptance criteria of sample receipt in laboratory to transfusion commencement in transfusion dependent thalassaemia with respect to alloimmunisation. To determine the safety of electronic issue of blood components in such a setting. Retrospective audit of alloimmunisation (1999-2012) and blood exposure in registered thalassaemia patients at a central London thalassaemia centre where the acceptance criteria for the group and save sample from arrival in the laboratory to the time of issue of blood for transfusion for someone who has been transfused in the last 28 days was 1 week, and there was electronic issue protocol for patients who have always had a negative antibody screen (other than temporary positivity in pregnant women receiving prophylactic anti-D or anti Le-a, Anti Le-b and Anti P1 that are no longer detectable). There were 133 patients with thalassemia variants regularly attending UCLH for review. A total of 105 patients had transfusion dependent thalassaemia (TDT) (7 E-beta thalassaemia, 98 beta thalassaemia major). Ten of the 84 patients who received their transfusions at UCLH were alloimmunised. Seven of them had been alloimmunised prior to arrival at UCLH. Only two patients developed antibodies at UCLH during this period. The prevalence of alloantibody formation of 2% in UCLH transfused patients, with presumptive incidence of 0.01 alloantibodies per 100 units or 0·001 immunisations per person per year compares favourably with other reported series and suggests that 1 week interval with appropriate electronic issue is acceptable practice. © 2015 British Blood Transfusion Society.

  16. Identification of permit and waste acceptance criteria provisions requiring modification for acceptance of commercial mixed waste

    International Nuclear Information System (INIS)

    1994-03-01

    In October 1990, representatives of States and compact regions requested that the US Department of Energy (DOE) explore an agreement with host States and compact regions under which DOE would accept commercial mixed low-level radioactive waste (LLW) at DOE's own treatment and disposal facilities. A program for DOE management of commercial mixed waste is made potentially more attractive in light of the low commercial mixed waste volumes, high regulatory burdens, public opposition to new disposal sites, and relatively high cost of constructing commercial disposal facilities. Several studies were identified as essential in determining the feasibility of DOE accepting commercial mixed waste for disposal. The purpose of this report is to identify any current or proposed waste acceptance criteria (WAC) or Resource Conservation and Recovery Act (RCRA) provisions that would have to be modified for commercial mixed waste acceptance at specified DOE facilities. Following the introduction, Section 2 of this report (a) provides a background summary of existing and proposed mixed waste disposal facilities at each DOE site, and (b) summarizes the status of any RCRA Part B permit and WAC provisions relating to the disposal of mixed waste, including provisions relating to acceptance of offsite waste. Section 3 provides overall conclusions regarding the current status and permit modifications that must be implemented in order to grant DOE sites authority under their permits to accept commercial mixed waste for disposal. Section 4 contains a list of references

  17. Acceptance criteria for the ITER divertor vertical target

    International Nuclear Information System (INIS)

    Fouquet, S.; Schlosser, J.; Merola, M.; Durocher, A.; Escourbiac, F.; Grosman, A.; Missirlian, M.; Portafaix, C.

    2006-01-01

    In the frame of the toroidal pump limiter fabrication for Tore Supra, CEA developed a large experience of infrared test for acceptance of high heat flux components armoured with carbon fibre composite flat tiles. The test is based on a thermal transient induced by an alternative hot/cold water flow in the heat sink structure. The tile surface temperature transients are compared with those of a reference element, the maximum difference for each tile leading to a value called ΔT ref m ax . This method is proposed for the commissioning of plasma facing components for the ITER divertor vertical target. This paper describes the determination of the best acceptance criteria for the 'monoblock' geometry of the carbon part. First, it has been shown that the location and the extension of the defects could reliably be determined by monitoring both top and lateral surfaces during the test. Second, it was possible to fix an acceptance method based on ΔT ref m ax . Samples with calibrated defects are now under fabrication to validate the results

  18. Acceptance criteria for disposal of radioactive waste in Romania

    International Nuclear Information System (INIS)

    Dogaru, D.

    2001-01-01

    In Romania the institutional radioactive waste are managed by National Institute of R and D for Physics and Nuclear Engineering. The institutional radioactive waste are collected, treated and conditioned at the Radioactive Waste Treatment Plant then transferred and disposed to the National Repository of Radioactive Waste at Baita Bihor. National Repository for Radioactive Waste is a long term storage facility. The repository is placed in a former worked out uranium ore mine, being excavated in the Bihor peak. The repository has been sited taking into account the known geological, hydrogeoloical, seismic and meteorological and mining properties of a uranium mining site. In the absence of an updated Safety Analysis Report, the maximum radioactive content permitted by the regulatory authority in the operation license is below the values reported for other engineered repositories in mine galleries. The paper presents the acceptance criteria for disposal of radioactive waste in National Repository for Radioactive Waste at Baita Bihor. (author)

  19. Determination of acceptable risk criteria for nuclear waste management

    International Nuclear Information System (INIS)

    Cohen, J.J.

    1977-01-01

    The initial phase of the work performed during FY 1977 consisted of performing a ''scoping'' study to define issues, determine an optimal methodology for their resolution, and compile a data base for acceptable risk criteria development. The issues, spanning technical, psychological, and ethical dimensions, were categorized in seven major areas: (1) unplanned or accidental events, (2) present vs future risks, (3) institutional controls and retrievability, (4) dose-response mechanism and uncertainty, (5) spatial distribution of exposed populations, (6) different types of nuclear wastes, and (7) public perception. The optimum methodology for developing ARC was determined to be multi-attribute decision analysis encompassing numerous specific techniques for choosing, from among several alternatives, the optimal course of action when the alternatives are constrained to meet specified attributes. The data base developed during the study comprises existing regulations and guidelines, maximum permissible dose, natural geologic hazards, nonradioactive hazardous waste practices, bioethical perspectives, and data from an opinion survey

  20. Determination of acceptable risk criteria for nuclear waste management

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, J.J.

    1977-10-21

    The initial phase of the work performed during FY 1977 consisted of performing a ''scoping'' study to define issues, determine an optimal methodology for their resolution, and compile a data base for acceptable risk criteria development. The issues, spanning technical, psychological, and ethical dimensions, were categorized in seven major areas: (1) unplanned or accidental events, (2) present vs future risks, (3) institutional controls and retrievability, (4) dose-response mechanism and uncertainty, (5) spatial distribution of exposed populations, (6) different types of nuclear wastes, and (7) public perception. The optimum methodology for developing ARC was determined to be multi-attribute decision analysis encompassing numerous specific techniques for choosing, from among several alternatives, the optimal course of action when the alternatives are constrained to meet specified attributes. The data base developed during the study comprises existing regulations and guidelines, maximum permissible dose, natural geologic hazards, nonradioactive hazardous waste practices, bioethical perspectives, and data from an opinion survey.

  1. Acceptance criteria for the evaluation of nuclear power reactor security plans

    International Nuclear Information System (INIS)

    1982-08-01

    This guidance document contains acceptance criteria to be used in the NRC license review process. It contains specific criteria for use in evaluating the acceptability of nuclear power reactor security programs as detailed in security plans

  2. 78 FR 53483 - Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 3

    Science.gov (United States)

    2013-08-29

    ... NUCLEAR REGULATORY COMMISSION [Docket No. 052-00025; NRC-2008-0252] Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 3 AGENCY: Nuclear Regulatory Commission. ACTION: Determination of inspections, tests, analyses, and acceptance criteria (ITAAC) completion...

  3. 78 FR 53484 - Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 4

    Science.gov (United States)

    2013-08-29

    ... NUCLEAR REGULATORY COMMISSION [Docket No. 052-00026; NRC-2008-0252] Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 4 AGENCY: Nuclear Regulatory Commission. ACTION: Determination of inspections, tests, analyses, and acceptance criteria (ITAAC) completion...

  4. 78 FR 38411 - Vogtle Electric Generating Plant, Unit 4; Inspections, Tests, Analyses, and Acceptance Criteria

    Science.gov (United States)

    2013-06-26

    ... Plant, Unit 4; Inspections, Tests, Analyses, and Acceptance Criteria AGENCY: Nuclear Regulatory Commission. ACTION: Determination of inspections, tests, analyses, and acceptance criteria completion. SUMMARY: The U.S. Nuclear Regulatory Commission (NRC) staff has determined that the inspections, tests...

  5. 78 FR 65007 - Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 3

    Science.gov (United States)

    2013-10-30

    ... NUCLEAR REGULATORY COMMISSION [Docket No. 052-00026; NRC-2008-0252] Inspections, Tests, Analyses, and Acceptance Criteria; Vogtle Electric Generating Plant, Unit 3 AGENCY: Nuclear Regulatory Commission. ACTION: Determination of inspections, tests, analyses, and acceptance criteria completion...

  6. Safety analysis, risk assessment, and risk acceptance criteria

    International Nuclear Information System (INIS)

    Jamali, K.

    1997-01-01

    This paper discusses a number of topics that relate safety analysis as documented in the Department of Energy (DOE) safety analysis reports (SARs), probabilistic risk assessments (PRA) as characterized primarily in the context of the techniques that have assumed some level of formality in commercial nuclear power plant applications, and risk acceptance criteria as an outgrowth of PRA applications. DOE SARs of interest are those that are prepared for DOE facilities under DOE Order 5480.23 and the implementing guidance in DOE STD-3009-94. It must be noted that the primary area of application for DOE STD-3009 is existing DOE facilities and that certain modifications of the STD-3009 approach are necessary in SARs for new facilities. Moreover, it is the hazard analysis (HA) and accident analysis (AA) portions of these SARs that are relevant to the present discussions. Although PRAs can be qualitative in nature, PRA as used in this paper refers more generally to all quantitative risk assessments and their underlying methods. HA as used in this paper refers more generally to all qualitative risk assessments and their underlying methods that have been in use in hazardous facilities other than nuclear power plants. This discussion includes both quantitative and qualitative risk assessment methods. PRA has been used, improved, developed, and refined since the Reactor Safety Study (WASH-1400) was published in 1975 by the Nuclear Regulatory Commission (NRC). Much debate has ensued since WASH-1400 on exactly what the role of PRA should be in plant design, reactor licensing, 'ensuring' plant and process safety, and a large number of other decisions that must be made for potentially hazardous activities. Of particular interest in this area is whether the risks quantified using PRA should be compared with numerical risk acceptance criteria (RACs) to determine whether a facility is 'safe.' Use of RACs requires quantitative estimates of consequence frequency and magnitude

  7. An approach to societal risk acceptance criteria and risk management

    International Nuclear Information System (INIS)

    Okrent, D.; Whipple, C.

    1977-06-01

    A quantitative approach to risk acceptance criteria and risk management is proposed for activities involving risk to individuals not receiving direct benefits, such as employment, from the activity. Societal activities are divided into major facilities or technologies, all or part of which are categorized as essential, beneficial, or peripheral, and a decreasing level of acceptable risk to the most exposed individual is proposed (say, 0.0002/year for essential, 0.00001/year for beneficial, and 0.000002/year for peripheral activity). The risk would be assessed at a high confidence level (say, 90%), thereby providing an incentive to the gaining of better knowledge. Each risk-producing facility, technology, etc., would have to undergo assessment both of risk to the individual and to society. The cost of the latter would have to be internalized, probably via a tax paid to the Federal Government, which in turn would redistribute the benefit as national health insurance or reduced taxes to the individual. Risk aversion to large events would be built into the internalization of the cost of risk

  8. Expanded criteria donor kidneys for younger recipients: acceptable outcomes.

    Science.gov (United States)

    Goplani, K R; Kute, V B; Vanikar, A V; Shah, P R; Gumber, M R; Patel, H V; Modi, P R; Trivedi, H L

    2010-12-01

    European senior programme (ESP) is well known for acceptable outcomes using expanded criteria donor (ECD) kidneys from donors older than 65 years for recipients older than 65 years. The incidence of end-stage renal disease (ESRD) is 229/million in India with a mean age of 45 years. We performed a retrospective analysis of transplantation of ECD versus standard criteria donor (SCD) kidneys into younger recipients. Forty-three ECD transplantations among 158 deceased donor organ transplantation (DDOT) were performed between January 2006 and December 2009. Among 43 transplantation from 30 donors, 14 were dual kidney transplantations (DKT) performed based upon biopsy evaluation. All recipients received thymoglobulin (rATG) induction followed by immunosuppression with a steroid, mycophenolate mofetil (MMF), and a calcineurin inhibitor. Statistical analysis used chi-square test and unpaired Student t test. Kaplan-Meier curves were used for survival analysis. For ECD the mean donor age was 64 ± 11 years. Cerebrovascular accidents (CVA) were the cause of death among 60% of donors, 73.13% of whom were hypertensive and 23.13% diabetic. Mean DKT donor age was 75 ± 9.17 years versus 60 ± 8.0 years for single kidney transplantation (SKT). Mean recipient age of DKT versus SKT was 44 ± 12.4 years versus 43 ± 14 years. Mean serum creatinine (SCr; mg/dL) of SKT patients was 1.64 ± 0.75 versus 1.68 ± 0.46 in DKT. Mean follow-up was 455 ± 352 days. Mean SCr of 43 ECD recipients of mean age, 43.4 ± 14.2 years was 1.61 ± 0.61 mg/dL. Among 43 recipients, 23.25% were diabetic, 41.86% displayed delayed graft function (DGF), and 23.25% experienced biopsy-proven acute rejection (BPAR). Patient survival rate was 72.09% and graft survival rate was 67.44%. For SCD transplantations (n = 115), the mean donor age was 36 ± 14 years and recipient mean age was 32.8 ± 14.07 years. Mean SCr was 1.32 ± 0.46 mg/dL with 26.95% recipients displaying DGF, whereas 20.86% had BPAR. In the SCD

  9. Data Quality Objectives for WTP Feed Acceptance Criteria - 12043

    Energy Technology Data Exchange (ETDEWEB)

    Arakali, Aruna V.; Benson, Peter A.; Duncan, Garth; Johnston, Jill C.; Lane, Thomas A.; Matis, George; Olson, John W. [Hanford Tank Waste Treatment and Immobilization Plant (United States); Banning, Davey L.; Greer, Daniel A.; Seidel, Cary M.; Thien, Michael G. [Hanford Tank Operations Contractor - Washington River Protection Solutions, Richland, WA 99354 (United States)

    2012-07-01

    The Hanford Tank Waste Treatment and Immobilization Plant (WTP) is under construction for the U.S. Department of Energy by Bechtel National, Inc. and subcontractor URS Corporation (contract no. DE-AC27-01RV14136). The plant when completed will be the world's largest nuclear waste treatment facility. Bechtel and URS are tasked with designing, constructing, commissioning, and transitioning the plant to the long term operating contractor to process the legacy wastes that are stored in underground tanks (from nuclear weapons production between the 1940's and the 1980's). Approximately 56 million gallons of radioactive waste is currently stored in these tanks at the Hanford Site in southeastern Washington. There are three major WTP facilities being constructed for processing the tank waste feed. The Pretreatment (PT) facility receives feed where it is separated into a low activity waste (LAW) fraction and a high level waste (HLW) fraction. These fractions are transferred to the appropriate (HLW or LAW) facility, combined with glass former material, and sent to high temperature melters for formation of the glass product. In addition to PT, HLW and LAW, other facilities in WTP include the Laboratory (LAB) for analytical services and the Balance of Facilities (BOF) for plant maintenance, support and utility services. The transfer of staged feed from the waste storage tanks and acceptance in WTP receipt vessels require data for waste acceptance criteria (WAC) parameters from analysis of feed samples. The Data Quality Objectives (DQO) development was a joint team effort between WTP and Tank Operations Contractor (TOC) representatives. The focus of this DQO effort was to review WAC parameters and develop data quality requirements, the results of which will determine whether or not the staged feed can be transferred from the TOC to WTP receipt vessels. The approach involved systematic planning for data collection consistent with EPA guidance for the seven

  10. On the consistency of risk acceptance criteria with normative theories for decision-making

    Energy Technology Data Exchange (ETDEWEB)

    Abrahamsen, E.B. [University of Stavanger, 4036 Stavanger (Norway)], E-mail: eirik.abrahamsen@uis.no; Aven, T. [University of Stavanger, 4036 Stavanger (Norway)

    2008-12-15

    In evaluation of safety in projects it is common to use risk acceptance criteria to support decision-making. In this paper, we discuss to what extent the risk acceptance criteria is in accordance with the normative theoretical framework of the expected utility theory and the rank-dependent utility theory. We show that the use of risk acceptance criteria may violate the independence axiom of the expected utility theory and the comonotonic independence axiom of the rank-dependent utility theory. Hence the use of risk acceptance criteria is not in general consistent with these theories. The level of inconsistency is highest for the expected utility theory.

  11. On the consistency of risk acceptance criteria with normative theories for decision-making

    International Nuclear Information System (INIS)

    Abrahamsen, E.B.; Aven, T.

    2008-01-01

    In evaluation of safety in projects it is common to use risk acceptance criteria to support decision-making. In this paper, we discuss to what extent the risk acceptance criteria is in accordance with the normative theoretical framework of the expected utility theory and the rank-dependent utility theory. We show that the use of risk acceptance criteria may violate the independence axiom of the expected utility theory and the comonotonic independence axiom of the rank-dependent utility theory. Hence the use of risk acceptance criteria is not in general consistent with these theories. The level of inconsistency is highest for the expected utility theory

  12. Development of comprehensive waste acceptance criteria for commercial nuclear waste

    International Nuclear Information System (INIS)

    O'Hara, F.A.; Miller, N.E.; Ausmus, B.S.; Yates, K.R.; Means, J.L.; Christensen, R.N.; Kulacki, F.A.

    1979-01-01

    A detailed methodology is presented for the identification of the characteristics of commercial nuclear waste which may require criteria. This methodology is analyzed as a six-step process which begins with identification of waste operations and proceeds until the waste characteristics affecting the potential release of radionuclides are determined. All waste types and operations were analyzed using the methodology presented. Several illustrative example are included. It is found that thirty-three characteristics can be identified as possibly requiring criteria

  13. Human factors engineering design review acceptance criteria for the safety parameter display

    International Nuclear Information System (INIS)

    McGevna, V.; Peterson, L.R.

    1981-01-01

    This report contains human factors engineering design review acceptance criteria developed by the Human Factors Engineering Branch (HFEB) of the Nuclear Regulatory Commission (NRC) to use in evaluating designs of the Safety Parameter Display System (SPDS). These criteria were developed in response to the functional design criteria for the SPDS defined in NUREG-0696, Functional Criteria for Emergency Response Facilities. The purpose of this report is to identify design review acceptance criteria for the SPDS installed in the control room of a nuclear power plant. Use of computer driven cathode ray tube (CRT) displays is anticipated. General acceptance criteria for displays of plant safety status information by the SPDS are developed. In addition, specific SPDS review criteria corresponding to the SPDS functional criteria specified in NUREG-0696 are established

  14. Nevada test site defense waste acceptance criteria, certification, and transfer requirements

    International Nuclear Information System (INIS)

    1988-10-01

    The Nevada Test Site (NTS) Defense Waste Acceptance Criteria, Certification and Transfer Requirements establishes procedures and criteria for safe transfer, disposal, and storage of defense transuranic, low-level, and mixed waste at the NTS. Included are an overview of the NTS defense waste management program; the NTS waste acceptance criteria for transuranic, low-level, and mixed wastes; waste certification requirements and guidance; application to submit waste; and requirements for waste transfer and receipt. 5 figs., 16 tabs

  15. Nevada Test Site waste acceptance criteria [Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    None

    1997-08-01

    Revision one updates the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document.

  16. Nevada Test Site waste acceptance criteria [Revision 1

    International Nuclear Information System (INIS)

    None

    1997-01-01

    Revision one updates the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive and mixed waste for disposal; and transuranic and transuranic mixed waste for interim storage at the NTS. Review each section of this document. This document is not intended to include all of the requirements; rather, it is meant as a guide toward meeting the regulations. All references in this document should be observed to avoid omission of requirements on which acceptance or rejection of waste will be based. The Department of Energy/Nevada Operations Office (DOE/NV) and support contractors are available to assist you in understanding or interpreting this document

  17. Review of issues relevant to acceptable risk criteria for nuclear waste management

    International Nuclear Information System (INIS)

    Cohen, J.J.

    1978-01-01

    Development of acceptable risk criteria for nuclear waste management requires the translation of publicly determined goals and objectives into definitive issues which, in turn, require resolution. Since these issues are largely of a subjective nature, they cannot be resolved by technological methods. Development of acceptable risk criteria might best be accomplished by application of a systematic methodology for the optimal implementation of subjective values. Multi-attribute decision analysis is well suited for this purpose

  18. Summary of research and development activities in support of waste acceptance criteria for WIPP

    International Nuclear Information System (INIS)

    Hunter, T.O.

    1979-11-01

    The development of waste acceptance criteria for the Waste Isolation Pilot Plant (WIPP) is summarized. Specifications for acceptable waste forms are included. Nine program areas are discussed. They are: TRU characterization, HLW interactions, thermal/structural interactions, nuclide migration, permeability, brine migration, borehole plugging, operation/design support, and instrumentation development. Recommendations are included

  19. Acceptance criteria for deposition of low-level and intermediate-level radiation levels radioactive wastes

    International Nuclear Information System (INIS)

    2002-09-01

    This norm establishes the criteria for acceptance low and intermediate radiation level for safe deposition in repositories, for assuring the protection of workers, population and environment against the hazardous effects of the ionizing radiations. The criteria of this norm applies to the low and intermediate radiation levels

  20. On the use of risk acceptance criteria in the offshore oil and gas industry

    International Nuclear Information System (INIS)

    Aven, Terje; Vinnem, Jan Erik

    2005-01-01

    Risk acceptance criteria, as upper limits of acceptable risks, have been used for offshore activities on the Norwegian Continental Shelf for more than 20 years. The common thinking has been that risk analyses and assessments cannot be conducted in a meaningful way without the use of such criteria. The ALARP principle also applies, but the risk acceptance criteria have played a more active role in the assessment processes than seen for example in the UK. Recently there has, however, been a discussion about the suitability of risk acceptance criteria to assess and control risks. The purpose of this paper is to contribute to this discussion by presenting and discussing a risk analysis regime that is not based on the use of risk acceptance criteria at all. We believe that we can do better if cost-effectiveness (in a wide sense) is the ruling thinking rather than adoption of pre-defined risk acceptance limits. This means a closer resemblance with the ALARP principle as adopted in the UK and other countries, but is not a direct application of this practice. Also the building blocks of the common way of applying the ALARP principle are reviewed. The Norwegian offshore oil and gas industry is the starting point, but the discussion is to large extent general

  1. Acceptance criteria for disposal of radioactive wastes in shallow ground and rock cavities

    International Nuclear Information System (INIS)

    1985-01-01

    This document provides an overview of basic information related to waste acceptance criteria for disposal in shallow ground and rock cavity repositories, consisting of a discussion of acceptable waste types. The last item includes identification of those waste characteristics which may influence the performance of the disposal system and as such are areas of consideration for criteria development. The material is presented in a manner similar to a safety assessment. Waste acceptance criteria aimed at limiting the radiation exposure to acceptable levels are presented for each pathway. Radioactive wastes considered here are low-level radioactive wastes and intermediate-level radioactive wastes from nuclear fuel cycle operations and applications of radionuclides in research, medicine and industry

  2. Preparation of acceptance tests and criteria for the Test Blanket Systems to be operated in ITER

    Energy Technology Data Exchange (ETDEWEB)

    Laan, J.G. van der, E-mail: JaapG.vanderLaan@iter.org [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Cuquel, B. [AIRBUS Defence and Space S.A.S., 13115 Saint Paul Lez Durance (France); Demange, D.; Ghidersa, B.-E. [Karlsruhe Institute of Technology, Karlsruhe (Germany); Giancarli, L.M.; Iseli, M.; Jourdan, T. [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Nevière, J.-C. [Comex-Nucleaire, 13115 Saint Paul Lez Durance (France); Pascal, R.; Ring, W. [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France)

    2015-10-15

    Highlights: • Initial guideline for acceptance testing and acceptance criteria for Test Blanket Systems in ITER. • These tests complement those required by the applicable codes and standards, and regulations. • Completion of TBS manufacture will be followed by Factory Acceptance Testing, prior to shipment. • Next steps are “Reception Inspection Tests”, and on-site pre-installation and components tests. • This guideline allows the detailing of the TBS specific test plans and their scheduling. - Abstract: This paper describes the main acceptance criteria and required acceptance tests for the components of the six Test Blanket Systems to be installed and operated in ITER. It summarizes the guide-line toward the establishment of detailed test plans for the TBS, starting from the end-product at the ITER Members factories, and to generally define the type of tests that have to be performed on the ITER site after shipment, and/or prior to the systems final commissioning phase.

  3. A comparison and cross-reference of commercial low-level radioactive waste acceptance criteria

    International Nuclear Information System (INIS)

    Kerr, T.A.

    1997-04-01

    This document, prepared by the National Low-Level Waste Management Program at the Idaho National Engineering and Environmental Laboratory, is a comparison and cross-reference of commercial low-level radioactive waste acceptance criteria. Many of these are draft or preliminary criteria as well as implemented criteria at operating low-level radioactive waste management facilities. Waste acceptance criteria from the following entities are included: US Nuclear Regulatory Commission, South Carolina, Washington, Utah, Nevada, California, illinois, Texas, North Carolina, Nebraska, Pennsylvania, New York, and the Midwest Compact Region. Criteria in the matrix include the following: physical form, chemical form, liquid limits, void space in packages, concentration averaging, types of packaging, chelating agents, solidification media, stability requirements, sorptive media, gas, oil, biological waste, pyrophorics, source material, special nuclear material, package dimensions, incinerator ash, dewatered resin, transuranics, and mixed waste. Each criterion in the matrix is cross-referenced to its source document so that exact requirements can be determined

  4. Why risk acceptance criteria need to be defined by the authorities and not the industry?

    International Nuclear Information System (INIS)

    Abrahamsen, Eirik Bjorheim; Aven, Terje

    2012-01-01

    In various industries it is common to use risk acceptance criteria to support decision-making. The criteria are seen as absolute in the sense that measures need to be implemented if the criteria are not met. In Norway the petroleum regulations state that the operator has a duty to formulate risk acceptance criteria relating to major accidents and to the environment. This practice is in line with the internal control principle, which states that the operator has the full responsibility for identifying the hazards and seeing that they are controlled. In this paper we discuss the rationale for this practice. The expected utility theory, which is the backbone for all economic thinking, is used as a basis for the discussion. We show that if risk acceptance criteria are to be introduced as a risk management tool, they should be formulated by the authorities, as is the common scheme seen in many countries and industries, for example in the UK. Risk acceptance criteria formulated by the industry would not in general serve the interest of the society as a whole.

  5. Development on inelastic analysis acceptance criteria for radioactive material transportation packages

    International Nuclear Information System (INIS)

    Ammerman, D.J.; Ludwigsen, J.S.

    1995-01-01

    The response of radioactive material transportation packages to mechanical accident loadings can be more accurately characterized by non-linear dynamic analysis than by the ''Equivalent dynamic'' static elastic analysis typically used in the design of these packages. This more accurate characterization of the response can lead to improved package safety and design efficiency. For non-linear dynamic analysis to become the preferred method of package design analysis, an acceptance criterion must be established that achieves an equivalent level of safety as the currently used criterion defined in NRC Regulatory Guide 7.6 (NRC 1978). Sandia National Laboratories has been conducting a study of possible acceptance criteria to meet this requirement. In this paper non-linear dynamic analysis acceptance criteria based on stress, strain, and strain-energy-density will be discussed. An example package design will be compared for each of the design criteria, including the approach of NRC Regulatory Guide 7.6

  6. A Method to Improve the Software Acceptance Criteria for Nuclear Power Plants

    International Nuclear Information System (INIS)

    Suh, Yong Suk; Park, Heui Youn; Son, Ki Sung; Lee, Ki Hyun; Kim, Hyeon Soo

    2005-01-01

    The license is a mandatory process required by a governmental authority and the certification is a voluntary process administrated by a professional community. A software certification is a result of an assessment that the certified software conforms to required criteria or standards. The certification is used as a committed promise to produce a high quality software, so software acquirers are requiring it from their suppliers. For example, US DoD (Department of Defense) requires an achievement of CMMI-SW (Capability Maturity Model Integration-Software) certification for participating in a major military software project. It is commonly said that the purpose of achieving a certification is to improve the product quality. In the nuclear area, a software certification has been rarely concerned with or required for the software used in a safety function of NPPs (Nuclear Power Plants). The safety critical software for NPPs is accepted by the nuclear regulators when the following three criteria are met: acceptable plans should be prepared to control the software development activities, the plans should be followed in an acceptable software life cycle, and the process should produce acceptable design outputs. The acceptance criteria are so abstractive that the nuclear regulators may assess the software development plans, activities, outputs based on their subjective engineering judgments. This is inevitable because a software has invisible or intangible characteristics. It is hard to assess the totality of a software prior to running it. These have caused the judgments to be biased. The regulators may want some objectiveness in assessing how much capability for software development the supplier possesses. In that case, the software certification can assist them for such an assessment. This paper proposes a method to improve the software acceptance criteria by applying the software certification to the criteria. This will assist the regulators to assess the supplier

  7. Definition of acceptance criteria for the ITER divertor plasma-facing components through systematic experimental analysis

    International Nuclear Information System (INIS)

    Escourbiac, F; Richou, M; Guigon, R; Durocher, A; Schlosser, J; Grosman, A; Constans, S; Merola, M; Riccardi, B

    2009-01-01

    Experience has shown that a critical part of the high-heat flux (HHF) plasma-facing component (PFC) is the armour to heat sink bond. An experimental study was performed in order to define acceptance criteria with regards to thermal hydraulics and fatigue performance of the International Thermonuclear Experimental Reactor (ITER) divertor PFCs. This study, which includes the manufacturing of samples with calibrated artificial defects relevant to the divertor design, is reported in this paper. In particular, it was concluded that defects detectable with non-destructive examination (NDE) techniques appeared to be acceptable during HHF experiments relevant to heat fluxes expected in the ITER divertor. On the basis of these results, a set of acceptance criteria was proposed and applied to the European vertical target medium-size qualification prototype: 98% of the inspected carbon fibre composite (CFC) monoblocks and 100% of tungsten (W) monoblock and flat tiles elements (i.e. 80% of the full units) were declared acceptable.

  8. Definition of acceptance criteria for the ITER divertor plasma-facing components through systematic experimental analysis

    Science.gov (United States)

    Escourbiac, F.; Richou, M.; Guigon, R.; Constans, S.; Durocher, A.; Merola, M.; Schlosser, J.; Riccardi, B.; Grosman, A.

    2009-12-01

    Experience has shown that a critical part of the high-heat flux (HHF) plasma-facing component (PFC) is the armour to heat sink bond. An experimental study was performed in order to define acceptance criteria with regards to thermal hydraulics and fatigue performance of the International Thermonuclear Experimental Reactor (ITER) divertor PFCs. This study, which includes the manufacturing of samples with calibrated artificial defects relevant to the divertor design, is reported in this paper. In particular, it was concluded that defects detectable with non-destructive examination (NDE) techniques appeared to be acceptable during HHF experiments relevant to heat fluxes expected in the ITER divertor. On the basis of these results, a set of acceptance criteria was proposed and applied to the European vertical target medium-size qualification prototype: 98% of the inspected carbon fibre composite (CFC) monoblocks and 100% of tungsten (W) monoblock and flat tiles elements (i.e. 80% of the full units) were declared acceptable.

  9. Definition of acceptance criteria for the ITER divertor plasma-facing components through systematic experimental analysis

    Energy Technology Data Exchange (ETDEWEB)

    Escourbiac, F; Richou, M; Guigon, R; Durocher, A; Schlosser, J; Grosman, A [CEA/IRFM, F-13108, Saint-Paul-lez-Durance (France); Constans, S [AREVA-NP, Le Creusot (France); Merola, M [ITER Organization, Cadarache (France); Riccardi, B [Fusion For Energy, Barcelona (Spain)], E-mail: frederic.escourbiac@cea.fr

    2009-12-15

    Experience has shown that a critical part of the high-heat flux (HHF) plasma-facing component (PFC) is the armour to heat sink bond. An experimental study was performed in order to define acceptance criteria with regards to thermal hydraulics and fatigue performance of the International Thermonuclear Experimental Reactor (ITER) divertor PFCs. This study, which includes the manufacturing of samples with calibrated artificial defects relevant to the divertor design, is reported in this paper. In particular, it was concluded that defects detectable with non-destructive examination (NDE) techniques appeared to be acceptable during HHF experiments relevant to heat fluxes expected in the ITER divertor. On the basis of these results, a set of acceptance criteria was proposed and applied to the European vertical target medium-size qualification prototype: 98% of the inspected carbon fibre composite (CFC) monoblocks and 100% of tungsten (W) monoblock and flat tiles elements (i.e. 80% of the full units) were declared acceptable.

  10. Nevada Test Site Waste Acceptance Criteria (NTSWAC), Rev. 7-01

    Energy Technology Data Exchange (ETDEWEB)

    NSTec Environmental Management

    2009-05-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NTSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex for disposal.

  11. Nevada Test Site Waste Acceptance Criteria (NTSWAC), Rev. 7-01

    International Nuclear Information System (INIS)

    2009-01-01

    This document establishes the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office, Nevada Test Site Waste Acceptance Criteria (NTSWAC). The NTSWAC provides the requirements, terms, and conditions under which the Nevada Test Site (NTS) will accept low-level radioactive waste and mixed low-level waste for disposal. The NTSWAC includes requirements for the generator waste certification program, characterization, traceability, waste form, packaging, and transfer. The criteria apply to radioactive waste received at the NTS Area 3 and Area 5 Radioactive Waste Management Complex for disposal.

  12. Testing the validity and acceptability of the diagnostic criteria for Hoarding Disorder: a DSM-5 survey.

    Science.gov (United States)

    Mataix-Cols, D; Fernández de la Cruz, L; Nakao, T; Pertusa, A

    2011-12-01

    The DSM-5 Obsessive-Compulsive Spectrum Sub-Workgroup is recommending the creation of a new diagnostic category named Hoarding Disorder (HD). The validity and acceptability of the proposed diagnostic criteria have yet to be formally tested. Obsessive-compulsive disorder/hoarding experts and random members of the American Psychiatric Association (APA) were shown eight brief clinical vignettes (four cases meeting criteria for HD, three with hoarding behaviour secondary to other mental disorders, and one with subclinical hoarding behaviour) and asked to decide the most appropriate diagnosis in each case. Participants were also asked about the perceived acceptability of the criteria and whether they supported the inclusion of HD in the main manual. Altogether, 211 experts and 48 APA members completed the survey (30% and 10% response rates, respectively). The sensitivity and specificity of the HD diagnosis and the individual criteria were high (80-90%) across various types of professionals, irrespective of their experience with hoarding cases. About 90% of participants in both samples thought the criteria would be very/somewhat acceptable for professionals and sufferers. Most experts (70%) supported the inclusion of HD in the main manual, whereas only 50% of the APA members did. The proposed criteria for HD have high sensitivity and specificity. The criteria are also deemed acceptable for professionals and sufferers alike. Training of professionals and the development and validation of semi-structured diagnostic instruments should improve diagnostic accuracy even further. A field trial is now needed to confirm these encouraging findings with real patients in real clinical settings.

  13. 21 CFR 212.70 - What controls and acceptance criteria must I have for my finished PET drug products?

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 4 2010-04-01 2010-04-01 false What controls and acceptance criteria must I have... POSITRON EMISSION TOMOGRAPHY DRUGS (Eff. 12-12-2011) Finished Drug Product Controls and Acceptance § 212.70 What controls and acceptance criteria must I have for my finished PET drug products? (a) Specifications...

  14. Acceptance criteria for determining armed response force size at nuclear power plants

    International Nuclear Information System (INIS)

    1983-02-01

    This guidance document contains acceptance criteria to be used in the NRC license review process. It consists of a scored worksheet and guidelines for interpreting the worksheet score that can be used in determining the adequacy of the armed response force size at a nuclear power reactor facility

  15. Technical Basis For Radiological Acceptance Criteria For Uranium At The Y-12 National Security Complex

    Energy Technology Data Exchange (ETDEWEB)

    Veinot, K. G.

    2009-07-22

    The purpose of this report is to establish radiological acceptance criteria for uranium. Other factors for acceptance not considered include criticality safety concerns, contaminants to the process stream, and impacts to the Safety Basis for the affected facilities. Three types of criteria were developed in this report. They include limits on external penetrating and non-penetrating radiation and on the internal hazard associated with inhalation of the material. These criteria are intended to alleviate the need for any special controls beyond what are normally utilized for worker protection from uranium hazards. Any proposed exceptions would require case-by-case evaluations to determine cost impacts and feasibility. Since Y-12 has set rigorous ALARA goals for worker doses, the external limits are based on assumptions of work time involved in the movement of accepted material plus the desire that external doses normally received are not exceeded, and set so that no special personnel monitoring would be required. Internal hazard controls were established so that dose contributions from non-uranium nuclides would not exceed 10% of that expected from the uranium component. This was performed using a Hazard Index (HI) previously established for work in areas contaminated with non-uranium nuclides. The radiological acceptance criteria for uranium are summarized in Table 1. Note that these limits are based on the assumption that radioactive daughter products have reached equilibrium.

  16. 48 CFR 15.607 - Criteria for acceptance and negotiation of an unsolicited proposal.

    Science.gov (United States)

    2010-10-01

    ... and negotiation of an unsolicited proposal. 15.607 Section 15.607 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Unsolicited Proposals 15.607 Criteria for acceptance and negotiation of an unsolicited proposal. (a) A...

  17. 48 CFR 915.607 - Criteria for acceptance and negotiation of an unsolicited proposal.

    Science.gov (United States)

    2010-10-01

    ... and negotiation of an unsolicited proposal. 915.607 Section 915.607 Federal Acquisition Regulations System DEPARTMENT OF ENERGY CONTRACTING METHODS AND CONTRACT TYPES CONTRACTING BY NEGOTIATION Unsolicited Proposals 915.607 Criteria for acceptance and negotiation of an unsolicited proposal. (c) DOE's cost...

  18. 10 CFR 50.46a - Acceptance criteria for reactor coolant system venting systems.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Acceptance criteria for reactor coolant system venting systems. 50.46a Section 50.46a Energy NUCLEAR REGULATORY COMMISSION DOMESTIC LICENSING OF PRODUCTION AND... function of these systems. High point vents are not required for the tubes in U-tube steam generators...

  19. Basic considerations for the preparation of performance testing materials as related to performance evaluation acceptance criteria

    International Nuclear Information System (INIS)

    McCurdy, D.E.; Morton, J.S.

    2001-01-01

    The preparation of performance testing (PT) materials for environmental and radiobioassay applications involves the use of natural matrix materials containing the analyte of interest, the addition (spiking) of the analyte to a desired matrix (followed by blending for certain matrices) or a combination of the two. The distribution of the sample analyte concentration in a batch of PT samples will reflect the degree of heterogeneity of the analyte in the PT material and/or the reproducibility of the sample preparation process. Commercial and government implemented radioanalytical performance evaluation programs have a variety of acceptable performance criteria. The performance criteria should take into consideration many parameters related to the preparation of the PT materials including the within and between sample analyte heterogeneity, the accuracy of the quantification of an analyte in the PT material and to what 'known' value will a laboratory's result be compared. How sample preparation parameters affect the successful participation in performance evaluation (PE) programs having an acceptance criteria established as a percent difference from a 'known' value or in PE programs using other acceptance criteria, such as the guidance provided in ANSI N42.22 and N13.30 is discussed. (author)

  20. Typical design/qualification acceptance criteria for newly installed pipelines and equipment components of VVER-type NPPs

    International Nuclear Information System (INIS)

    Masopust, R.

    2003-01-01

    This paper describes in general the typical design/qualification acceptance criteria and seismic acceptance criteria in particular that are applicable for important to safety newly installed pipelines and equipment components of VVER-type already existing NPPs, specifically during the design verification phase of this newly installed equipment. These criteria are currently used for VVER 440-213 and VVER 1000 NPPs in Czech Republic and in Slovakia. The similar criteria are also used in Hungary. (author)

  1. Qualitative acceptance criteria for radioactive wastes to be disposed of in deep geological formations

    International Nuclear Information System (INIS)

    1990-05-01

    The present Safety Guide has to be seen as a companion document to the IAEA Safety Series No. 99. It is concerned with the waste form which is an important component of the overall disposal system. Because of the broad range of waste types and conditioned forms and variations in the sites, designs and constructional approaches being considered for deep geological repositories, this report necessarily approaches the waste acceptance criteria in a general way, recognizing that the assignment of quantitative limits to these criteria has to be the responsibility of national authorities. The main objective of this Safety Guide is to set out qualitative waste acceptance criteria as a basis for specifying quantitative limits for the waste forms and packages which are intended to be disposed of in deep geological repositories. It should serve as guidance for assigning such parameter values which would fully comply with the safety assessment and performance of a waste disposal system as a whole. This document is intended to serve both national authorities and regulatory bodies involved in the development of deep underground disposal systems. The qualitative waste acceptance criteria dealt with in the present Safety Guide are primarily concerned with the disposal of high level, intermediate level and long-lived alpha bearing wastes in deep geological repositories. Although some criteria are also applicable in other waste disposal concepts, it has to be borne in mind that the set of criteria presented here shall ensure the isolation capability of a waste disposal system for periods of time much longer than for other waste streams with shorter lifetimes. 51 refs, 1 tab

  2. Defining waste acceptance criteria for the Hanford Replacement Cross-Site Transfer System

    International Nuclear Information System (INIS)

    Hudson, J.D.

    1996-04-01

    This document provides a methodology for defining waste acceptance criteria for the Hanford Replacement Cross-Site Transfer System (RCSTS). This methodology includes characterization, transport analysis, and control. A framework is described for each of these functions. A tool was developed for performing the calculations associated with the transport analysis. This tool, a worksheet that is available in formats acceptable for a variety of PC spreadsheet programs, enables a comparison of the pressure required to transport a given slurry at a rate that particulate suspension is maintained to the pressure drop available from the RCSTS

  3. Criteria for accepting piping thermal expansion movements during FFTF plant startup

    International Nuclear Information System (INIS)

    Clark, G.L.; Anderson, M.J.

    1981-03-01

    A deflection measurement program was conducted as a final step in the design qualification of the Fast Flux Test Facility liquid sodium piping. Measurements were obtained from the ambient empty position, through the 400 0 F (204 0 C) sodium fill, to an 800 0 F (427 0 C) maximum iso-thermal test condition. The program was designed to confirm that the pipe responded as predicted under both deadweight and thermal expansion loads. This paper describes the design of the test programs; the criteria used to select appropriate measurement locations from the approximately 4000 supports used on this pipe; and the criteria used to accept test results

  4. The use of acceptability criteria for radiological risk at AWE Aldermaston

    International Nuclear Information System (INIS)

    Thurston, B.B.; Tutt, K.J.; Zabierek, G.A.

    1989-01-01

    The limit-line approach to setting acceptable risk criteria for nuclear power plants is in general use in the United Kingdom. The Atomic Weapons Establishment (AWE) is a Ministry of Defence Establishment which contains a number of nuclear material processing facilities. Limit-line risk criteria have been used for some years to provide a framework within which identified hazards may be judged in a systematic manner, rather than on an ad hoc basis. This paper describes how this is applied to both new facilities and to changes made to existing ones including decommissioning. (author)

  5. HOW TO DEAL WITH WASTE ACCEPTANCE UNCERTAINTY USING THE WASTE ACCEPTANCE CRITERIA FORECASTING AND ANALYSIS CAPABILITY SYSTEM (WACFACS)

    International Nuclear Information System (INIS)

    Redus, K. S.; Hampshire, G. J.; Patterson, J. E.; Perkins, A. B.

    2002-01-01

    The Waste Acceptance Criteria Forecasting and Analysis Capability System (WACFACS) is used to plan for, evaluate, and control the supply of approximately 1.8 million yd3 of low-level radioactive, TSCA, and RCRA hazardous wastes from over 60 environmental restoration projects between FY02 through FY10 to the Oak Ridge Environmental Management Waste Management Facility (EMWMF). WACFACS is a validated decision support tool that propagates uncertainties inherent in site-related contaminant characterization data, disposition volumes during EMWMF operations, and project schedules to quantitatively determine the confidence that risk-based performance standards are met. Trade-offs in schedule, volumes of waste lots, and allowable concentrations of contaminants are performed to optimize project waste disposition, regulatory compliance, and disposal cell management

  6. HOW TO DEAL WITH WASTE ACCEPTANCE UNCERTAINTY USING THE WASTE ACCEPTANCE CRITERIA FORECASTING AND ANALYSIS CAPABILITY SYSTEM (WACFACS)

    Energy Technology Data Exchange (ETDEWEB)

    Redus, K. S.; Hampshire, G. J.; Patterson, J. E.; Perkins, A. B.

    2002-02-25

    The Waste Acceptance Criteria Forecasting and Analysis Capability System (WACFACS) is used to plan for, evaluate, and control the supply of approximately 1.8 million yd3 of low-level radioactive, TSCA, and RCRA hazardous wastes from over 60 environmental restoration projects between FY02 through FY10 to the Oak Ridge Environmental Management Waste Management Facility (EMWMF). WACFACS is a validated decision support tool that propagates uncertainties inherent in site-related contaminant characterization data, disposition volumes during EMWMF operations, and project schedules to quantitatively determine the confidence that risk-based performance standards are met. Trade-offs in schedule, volumes of waste lots, and allowable concentrations of contaminants are performed to optimize project waste disposition, regulatory compliance, and disposal cell management.

  7. Qualifications of and acceptance criteria for transporting special form radioactive material

    International Nuclear Information System (INIS)

    Hovingh, J.

    1991-01-01

    A special form radioactive material is a radioactive material that is in an inert, insoluble, indispersible form such that even in the event of an accident, it will not be dispersed into the environment in a way that could have an adverse impact on public health and safety. Methods of qualifying a special form radioactive material are discussed. Interpretation of acceptance criteria are proposed for the transportation of Type B quantities of a special form radioactive material. 11 refs

  8. Development of Waste Acceptance Criteria at 221-U Building: Initial Flow and Transport Scoping Calculations

    Energy Technology Data Exchange (ETDEWEB)

    Freedman, Vicky L.; Zhang, Z. F.; Keller, Jason M.; Chen, Yousu

    2007-05-30

    This report documents numerical flow and transport simulations performed that establish initial waste acceptance criteria for the potential waste streams that may be safely sequestered in the 221-U Building and similar canyon structures. Specifically, simulations were executed to identify the maximum loading of contaminant mass (without respect to volume) that can be emplaced within the 221-U Building with no more than 1 pCi/m2 of contaminant migrating outside the structure within a 1,000 year time period. The initial scoping simulations were executed in one dimension to assess important processes, and then two dimensions to establish waste acceptance criteria. Two monolithic conditions were assessed: (1) a grouted canyon monolith; and (2) a canyon monolith filled with sand, both assuming no cracks or fissures were present to cause preferential transport. A three-staged approach was taken to account for different processes that may impact the amount of contaminant that can be safely sequestered in canyon structure. In the first stage, flow and transport simulations established waste acceptance criteria based on a linear (Kd) isotherm approach. In the second stage, impacts on thermal loading were examined and the differences in waste acceptance criteria quantified. In the third stage of modeling, precipitation/dissolution reactions were considered on the release and transport of the contaminants, and the subsequent impact on the maximum contaminant loading. The reactive transport modeling is considered a demonstration of the reactive transport capability, and shows the importance of its use for future performance predictions once site-specific data have been obtained.

  9. Design loads, loading combinations and structural acceptance criteria for BWR containments in the United States

    International Nuclear Information System (INIS)

    Edwards, N.W.

    1979-01-01

    The definition of loads, loading combinations, and structural acceptance criteria used for the design and evaluation of BWR containments in the Unites States has become much more comprehensive over the past decade. The Mark I pressure suppression containment vessels were designed for a static design pressure, a design temperature, dead load and static equivalent earthquake. The current Mark III containments are being designed to accommodate many more loads such as safety relief valve discharge loads, and suppression pool hydrodynamic loadings associated with the steam condensation phenomena as well as pressure and temperature transients for a range of pipe break sizes. Consistent with the more comprehensive definition of loads and loading combinations, the ASME Code presently establishes structural acceptance criteria with different margins of safety by the definition of Service Level Assignments A, B, C and D. Acting in a responsible manner, United States utilities are currently evaluating and modifying existing containment vessels to account for the more detailed load definition and structural acceptance criteria. (orig.)

  10. Waste-acceptance criteria and risk-based thinking for radioactive-waste classification

    International Nuclear Information System (INIS)

    Lowenthal, M.D.

    1998-01-01

    The US system of radioactive-waste classification and its development provide a reference point for the discussion of risk-based thinking in waste classification. The official US system is described and waste-acceptance criteria for disposal sites are introduced because they constitute a form of de facto waste classification. Risk-based classification is explored and it is found that a truly risk-based system is context-dependent: risk depends not only on the waste-management activity but, for some activities such as disposal, it depends on the specific physical context. Some of the elements of the official US system incorporate risk-based thinking, but like many proposed alternative schemes, the physical context of disposal is ignored. The waste-acceptance criteria for disposal sites do account for this context dependence and could be used as a risk-based classification scheme for disposal. While different classes would be necessary for different management activities, the waste-acceptance criteria would obviate the need for the current system and could better match wastes to disposal environments saving money or improving safety or both

  11. Multi-Canister Overpack (MCO) Combustible Gas Management Leak Test Acceptance Criteria (OCRWM)

    International Nuclear Information System (INIS)

    SHERRELL, D.L.

    2000-01-01

    The purpose of this document is to support the Spent Nuclear Fuel Project's combustible gas management strategy while avoiding the need to impose any requirements for oxygen free atmospheres within storage tubes that contain multi-canister overpacks (MCO). In order to avoid inerting requirements it is necessary to establish and confirm leak test acceptance criteria for mechanically sealed and weld sealed MCOs that are adequte to ensure that, in the unlikely event the leak test results for any MCO were to approach either of those criteria, it could still be handled and stored in stagnant air without compromising the SNF Project's overall strategy to prevent accumulation of combustible gas mixtures within MCOs or within their surroundings. To support that strategy, this document: (1) establishes combustible gas management functions and minimum functional requirements for the MCO's mechanical seals and closure weld(s); (2) establishes a maximum practical value for the minimum required initial MCO inert backfill gas pressure; and (3) based on items 1 and 2, establishes and confirms leak test acceptance criteria for the MCO's mechanical seal and final closure weld(s)

  12. Long-Term Safety Analysis of Baldone Radioactive Waste Repository and Updating of Waste Acceptance Criteria

    International Nuclear Information System (INIS)

    2001-12-01

    The main objective of the project was to provide advice to the Latvian authorities on the safety enhancements and waste acceptance criteria for near surface radioactive waste disposal facilities of the Baldone repository. The project included the following main activities: Analysis of the current status of the management of radioactive waste in Latvia in general and, at the Baldone repository in particular Development of the short and long-term safety analysis of the Baldone repository, including: the planned increasing of capacity for disposal and long term storage, the radiological analysis for the post-closure period Development of the Environment Impact Statement, for the new foreseen installations, considering the non radiological components Proposal of recommendations for future updating of radioactive waste acceptance criteria Proposal of recommendations for safety upgrades to the facility. The work programme has been developed in phases and main tasks as follows. Phase 0: Project inception, Phase 1: Establishment of current status, plans and practices (Legislation, regulation and standards, Radioactive waste management, Waste acceptance criteria), Phase 2: Development of future strategies for long-term safety management and recommendations for safety enhancements. The project team found the general approach use at the installation, the basic design and the operating practices appropriate to international standards. Nevertheless, a number of items subject to potential improvements were also identified. These upgrading recommendations deal with general aspects of the management (mainly storage versus disposal of long-lived sources), site and environmental surveillance, packaging (qualification of containers, waste characterization requirements), the design of an engineered cap and strategies for capping. (author)

  13. Small bore pipe acceptance criteria for watts bar nuclear plant Tennessee Valley Authority

    International Nuclear Information System (INIS)

    Sun, W.S.; Lee, R.L.; Kalyanan, N.

    1991-01-01

    Small bore pipe (≤2 inches NPS) is traditionally analyzed by simplified techniques using Cook Book approach, which yield conservative results. However, reconciliation of these systems for as-built condition where the original criteria is observed to have been exceeded (or due to additions etc.) generally becomes a time consuming and expensive operation since a rigorous computer aided analysis or a detailed hand calculation becomes necessary. The acceptance criteria in this paper can be effectively used in such cases. The approach involves utilizing basic engineering principles and plant specific parameters (such as earthquake spectra) to estimate the system response such as pipe stress due to various loading conditions, piping frequency, support and anchor loads, valve acceleration etc

  14. Criteria of acceptability relating to the approval of consumer goods containing radioactive substances

    International Nuclear Information System (INIS)

    Paynter, R.A.

    1992-01-01

    The criteria are described which the Board intends to use when considering goods containing radioactive substances for approval under the regulations that the Government intends to make with respect to such goods. Some products are deemed unacceptable in principle because there would appear to be no justification for the use of radioactive substances in them. Examples of such products are given. Other products may be approved for supply to the public depending on the doses likely to be received by individuals, principally those who use the products. A lower dose is considered acceptable from products that do not contribute to safety than from products that do. In the interim, before the regulations are made, the criteria will be used as the basis of the Board's advice to suppliers and manufacturers of goods containing radioactive substances. (Author)

  15. Acceptance criteria for the physical protection upgrade rule requirements for fixed sites. Information guide

    International Nuclear Information System (INIS)

    Dwyer, P.

    1980-09-01

    This document has been developed as a tool to assist in providing consistent evaluation of upgraded physical security plans submitted in response to the Physical Protection Upgrade Rule, effective March 25, 1980. It presents a means for assuring licensee compliance with every regulatory requirement of particular significance to the protection of the public health and safety. Acceptance criteria are included to determine the extent to which each licensee meets the regulatory requirements. The format parallels Regulatory Guide 5.52, Standard Format and Content of a Licensee Physical Protection Plan for Strategic Special Nuclear Material at Fixed Sites

  16. RSE-M code progress in the field of examination evaluation and flaw acceptance criteria

    International Nuclear Information System (INIS)

    Barthelet, B.; Le Delliou, P.; Heliot, J.; Faidy, C.; Drubay, B.

    1995-01-01

    The RSE-M Code provides rules and requirements for in service inspection of light water cooled nuclear power plants. The code first edition was established by EDF and published in 1990 by AFCEN. In 1992, a second RSE-M project was launched by EDF and FRAMATOME with the objective to address a 1995 edition more completed considering the needs of owners, users, manufacturers and inspectors. This paper focuses on evaluation of examination results and presents the work done in the field of flaw acceptance criteria over the last three years. (author). 5 refs., 3 figs

  17. Acceptance criteria for the low enriched uranium reform amendments. Revision 1

    International Nuclear Information System (INIS)

    Emeigh, C.W.; Gundersen, G.E.; Withee, C.J.

    1985-04-01

    Revisions have been made to the material control and accounting requirements for NRC licensees authorized to possess and use more than one effective kilogram of special nuclear material of low strategic significance to have MC and A systems able to (1) confirm the presence of special nuclear material, (2) resolve indications of missing material, and (3) aid in the investigation and recovery of missing material. This document presents criteria that can be used to aid in judging the acceptability of licensee plans that would be submitted to the NRC for implementing these capabilities. General performance objectives, system capabilities, and recordkeeping are addressed

  18. From waste packages acceptance criteria to waste packages acceptance process at the Centre de l'Aube disposal facility

    International Nuclear Information System (INIS)

    Dutzer, M.

    2003-01-01

    The Centre de l'Aube disposal facility has now been operated for 10 years. At the end of 2001, about 124,000 m3 of low and intermediate level short lived waste packages, representing 180,000 packages, have been disposed, for a total capacity of 1,000,000 m3. The flow of waste packages is now between 12 and 15,000 m3 per year, that is one third of the flow that was taken into account for the design of the repository. It confirms the efforts by waste generators to minimise waste production. This flow represents 25 to 30,000 packages, 50% are conditioned into the compaction facility of the repository, so that 17,000 packages are disposed per year. 54 disposal vaults have been closed. In 1996-1999, the safety assessment of the repository have been reviewed, taking into account the experience of operation. This assessment was investigated by the regulatory body and, subsequently, a so-called 'definitive license' to operate was granted to ANDRA on September 2, 1999 with updated licensing requirements. Another review will be performed in 2004. To ensure a better consistency with the safety assessment of the facility, Andra issued new technical requirements for waste packages at the end of 2000. Discussions with waste generators also showed that the waste package acceptance process should be improved to provide a more precise definition of operational criteria to comply with in waste conditioning facilities. Consequently, a new approach has been implemented since 2000. (orig.)

  19. Characteristics of radioactive waste forms conditioned for storage and disposal: Guidance for the development of waste acceptance criteria

    International Nuclear Information System (INIS)

    1983-04-01

    This report attempts to review the characteristics of the individual components of the waste package, i.e. the waste form and the container, in order to formulate, where appropriate, quidelines for the development of practical waste acceptance criteria. Primarily the criteria for disposal are considered, but if more stringent criteria are expected to be necessary for storage or transportation prior to the disposal, these will be discussed. The report will also suggest test areas which will aid the development of the final waste acceptance criteria

  20. Preliminary Mark-18A (Mk-18A) Target Material Recovery Program Product Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, Sharon M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Patton, Bradley D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2016-09-01

    The Mk-18A Target Material Recovery Program (MTMRP) was established in 2015 to preserve the unique materials, e.g. 244Pu, in 65 previously irradiated Mk-18A targets for future use. This program utilizes existing capabilities at SRS and Savannah River National Laboratory (SRNL) to process targets, recover materials from them, and to package the recovered materials for shipping to ORNL. It also utilizes existing capabilities at ORNL to receive and store the recovered materials, and to provide any additional processing of the recovered materials or residuals required to prepare them for future beneficial use. The MTMRP is presently preparing for the processing of these valuable targets which is expected to begin in ~2019. As part of the preparations for operations, this report documents the preliminary acceptance criteria for the plutonium and heavy curium materials to be recovered from the Mk-18A targets at SRNL for transport and storage at ORNL. These acceptance criteria were developed based on preliminary concepts developed for processing, transporting, and storing the recovered Mk-18A materials. They will need to be refined as these concepts are developed in more detail.

  1. Technical basis for acceptance criteria on the susceptibility of digital systems to electromagnetic interference

    International Nuclear Information System (INIS)

    Ewing, P.D.; Korsah, K.; Antonescu, C.

    1992-01-01

    This paper discusses the development of the technical basis for establishing acceptance criteria on the susceptibility of digital systems to electromagnetic interference (EMI). The effort is sponsored by the US Nuclear Regulatory Commission and stems from the safety-related issues that need to be addressed with the application of digital instrumentation and controls systems in nuclear power plants. Designers of digital circuits are incorporating increasingly higher clock frequencies and lower logic voltage levels, thereby leading to the risk of susceptibility when spurious interference is misinterpreted as legitimate logic. Development of the technical basis for acceptance criteria centers around establishing good engineering practices to ensure that sufficient levels of electromagnetic compatibility (EMC) are maintained between the nuclear power plant's electronic and electromechanical systems. First, good EMC design and installation practices are needed to control the emissions from interference sources and their impact on other nearby circuits and systems. Then, a test and evaluation program is needed to outline the EMI tests to be performed, the associated test methods to be followed, and adequate test limits to ensure that the circuit or system under test meets the recommended guidelines. Test and evaluation should be followed by periodic maintenance to assess whether the recommended EMI control practices continue to be adhered to as part of the routine operation of the nuclear power plant. By following these steps, the probability of encountering safety-related problems associated with EMI will be greatly reduced

  2. Preliminary Mark-18A (Mk-18A) Target Material Recovery Program Product Acceptance Criteria

    International Nuclear Information System (INIS)

    Robinson, Sharon M.; Patton, Bradley D.

    2016-01-01

    The Mk-18A Target Material Recovery Program (MTMRP) was established in 2015 to preserve the unique materials, e.g. 244 Pu, in 65 previously irradiated Mk-18A targets for future use. This program utilizes existing capabilities at SRS and Savannah River National Laboratory (SRNL) to process targets, recover materials from them, and to package the recovered materials for shipping to ORNL. It also utilizes existing capabilities at ORNL to receive and store the recovered materials, and to provide any additional processing of the recovered materials or residuals required to prepare them for future beneficial use. The MTMRP is presently preparing for the processing of these valuable targets which is expected to begin in ~2019. As part of the preparations for operations, this report documents the preliminary acceptance criteria for the plutonium and heavy curium materials to be recovered from the Mk-18A targets at SRNL for transport and storage at ORNL. These acceptance criteria were developed based on preliminary concepts developed for processing, transporting, and storing the recovered Mk-18A materials. They will need to be refined as these concepts are developed in more detail.

  3. Methods for verifying compliance with low-level radioactive waste acceptance criteria

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-09-01

    This report summarizes the methods that are currently employed and those that can be used to verify compliance with low-level radioactive waste (LLW) disposal facility waste acceptance criteria (WAC). This report presents the applicable regulations representing the Federal, State, and site-specific criteria for accepting LLW. Typical LLW generators are summarized, along with descriptions of their waste streams and final waste forms. General procedures and methods used by the LLW generators to verify compliance with the disposal facility WAC are presented. The report was written to provide an understanding of how a regulator could verify compliance with a LLW disposal facility`s WAC. A comprehensive study of the methodology used to verify waste generator compliance with the disposal facility WAC is presented in this report. The study involved compiling the relevant regulations to define the WAC, reviewing regulatory agency inspection programs, and summarizing waste verification technology and equipment. The results of the study indicate that waste generators conduct verification programs that include packaging, classification, characterization, and stabilization elements. The current LLW disposal facilities perform waste verification steps on incoming shipments. A model inspection and verification program, which includes an emphasis on the generator`s waste application documentation of their waste verification program, is recommended. The disposal facility verification procedures primarily involve the use of portable radiological survey instrumentation. The actual verification of generator compliance to the LLW disposal facility WAC is performed through a combination of incoming shipment checks and generator site audits.

  4. Methods for verifying compliance with low-level radioactive waste acceptance criteria

    International Nuclear Information System (INIS)

    1993-09-01

    This report summarizes the methods that are currently employed and those that can be used to verify compliance with low-level radioactive waste (LLW) disposal facility waste acceptance criteria (WAC). This report presents the applicable regulations representing the Federal, State, and site-specific criteria for accepting LLW. Typical LLW generators are summarized, along with descriptions of their waste streams and final waste forms. General procedures and methods used by the LLW generators to verify compliance with the disposal facility WAC are presented. The report was written to provide an understanding of how a regulator could verify compliance with a LLW disposal facility's WAC. A comprehensive study of the methodology used to verify waste generator compliance with the disposal facility WAC is presented in this report. The study involved compiling the relevant regulations to define the WAC, reviewing regulatory agency inspection programs, and summarizing waste verification technology and equipment. The results of the study indicate that waste generators conduct verification programs that include packaging, classification, characterization, and stabilization elements. The current LLW disposal facilities perform waste verification steps on incoming shipments. A model inspection and verification program, which includes an emphasis on the generator's waste application documentation of their waste verification program, is recommended. The disposal facility verification procedures primarily involve the use of portable radiological survey instrumentation. The actual verification of generator compliance to the LLW disposal facility WAC is performed through a combination of incoming shipment checks and generator site audits

  5. Performance-based ECCS cladding acceptance criteria: A new simulation approach

    International Nuclear Information System (INIS)

    Zoino, A.; Alfonsi, A.; Rabiti, C.; Szilard, R.H.; Giannetti, F.; Caruso, G.

    2017-01-01

    Highlights: • A new methodology to demonstrate compliance with the new ECCS acceptance criteria is described. • A wide spectrum of fuel rod initial burnup states can be analysed in the design phase. • The coupled suite PHISICS/RELAP5-3D has been used in the analyses. • A demo simulation of the equilibrium cycle, load-following and a LOCA analysis has been performed. - Abstract: The U.S. Nuclear Regulatory Commission is currently proposing rulemaking to revise the Loss Of Coolant Accident (LOCA) and therefore the Emergency Core Cooling System (ECCS) acceptance criteria, to include the effects of higher burnup on cladding performance as well as to address other technical issues. As motivated by the new rule, the need to use advanced cladding designs may be a result. A loss of operational margin may result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licensee cost, as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. Consequently, there will be an increased focus on licensee decision making related to LOCA analysis to minimize cost and impact, and to manage margin. The study here presented has been part of a big project used to investigate technical issues and approaches for future industrial applications within the Risk-Informed Safety Margin Characterization (RISMC) Pathway. Specifically, the primary aim of this study is to lay out a roadmap to demonstrate the application of the new methodology. The present analysis shows a simplified version of the methodology of an industrial application on the Core Design and the Multi-Cycle Analysis.

  6. Contact-Handled Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant

    International Nuclear Information System (INIS)

    2005-01-01

    The purpose of this document is to summarize the waste acceptance criteria applicable to the transportation, storage, and disposal of contact-handled transuranic (CH-TRU) waste at the Waste Isolation Pilot Plant (WIPP). These criteria serve as the U.S. Department of Energy's (DOE) primary directive for ensuring that CH-TRU waste is managed and disposed of in a manner that protects human health and safety and the environment.The authorization basis of WIPP for the disposal of CH-TRU waste includes the U.S.Department of Energy National Security and Military Applications of Nuclear EnergyAuthorization Act of 1980 (reference 1) and the WIPP Land Withdrawal Act (LWA;reference 2). Included in this document are the requirements and associated criteriaimposed by these acts and the Resource Conservation and Recovery Act (RCRA,reference 3), as amended, on the CH-TRU waste destined for disposal at WIPP.|The DOE TRU waste sites must certify CH-TRU waste payload containers to thecontact-handled waste acceptance criteria (CH-WAC) identified in this document. Asshown in figure 1.0, the flow-down of applicable requirements to the CH-WAC istraceable to several higher-tier documents, including the WIPP operational safetyrequirements derived from the WIPP CH Documented Safety Analysis (CH-DSA;reference 4), the transportation requirements for CH-TRU wastes derived from theTransuranic Package Transporter-Model II (TRUPACT-II) and HalfPACT Certificates ofCompliance (references 5 and 5a), the WIPP LWA (reference 2), the WIPP HazardousWaste Facility Permit (reference 6), and the U.S. Environmental Protection Agency(EPA) Compliance Certification Decision and approval for PCB disposal (references 7,34, 35, 36, and 37). The solid arrows shown in figure 1.0 represent the flow-down of allapplicable payload container-based requirements. The two dotted arrows shown infigure 1.0 represent the flow-down of summary level requirements only; i.e., the sitesmust reference the regulatory source

  7. Contact-Handled Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant

    Energy Technology Data Exchange (ETDEWEB)

    Washington TRU Solutions LLC

    2005-12-29

    The purpose of this document is to summarize the waste acceptance criteria applicable to the transportation, storage, and disposal of contact-handled transuranic (CH-TRU) waste at the Waste Isolation Pilot Plant (WIPP). These criteria serve as the U.S. Department of Energy's (DOE) primary directive for ensuring that CH-TRU waste is managed and disposed of in a manner that protects human health and safety and the environment.The authorization basis of WIPP for the disposal of CH-TRU waste includes the U.S.Department of Energy National Security and Military Applications of Nuclear EnergyAuthorization Act of 1980 (reference 1) and the WIPP Land Withdrawal Act (LWA;reference 2). Included in this document are the requirements and associated criteriaimposed by these acts and the Resource Conservation and Recovery Act (RCRA,reference 3), as amended, on the CH-TRU waste destined for disposal at WIPP.|The DOE TRU waste sites must certify CH-TRU waste payload containers to thecontact-handled waste acceptance criteria (CH-WAC) identified in this document. Asshown in figure 1.0, the flow-down of applicable requirements to the CH-WAC istraceable to several higher-tier documents, including the WIPP operational safetyrequirements derived from the WIPP CH Documented Safety Analysis (CH-DSA;reference 4), the transportation requirements for CH-TRU wastes derived from theTransuranic Package Transporter-Model II (TRUPACT-II) and HalfPACT Certificates ofCompliance (references 5 and 5a), the WIPP LWA (reference 2), the WIPP HazardousWaste Facility Permit (reference 6), and the U.S. Environmental Protection Agency(EPA) Compliance Certification Decision and approval for PCB disposal (references 7,34, 35, 36, and 37). The solid arrows shown in figure 1.0 represent the flow-down of allapplicable payload container-based requirements. The two dotted arrows shown infigure 1.0 represent the flow-down of summary level requirements only; i.e., the sitesmust reference the regulatory source

  8. Derivation of Waste Acceptance Criteria for Low and Intermediate Level Waste in Surface Disposal Facility

    International Nuclear Information System (INIS)

    Gagner, L.; Voinis, S.

    2000-01-01

    In France, low- and intermediate-level radioactive wastes are disposed in a near-surface facility, at Centre de l'Aube disposal facility. This facility, which was commissioned in 1992, has a disposal capacity of one million cubic meters, and will be operated up to about 2050. It took over the job from Centre de la Manche, which was commissioned in 1969 and shut down in 1994, after having received about 520,000 cubic meters of wastes. The Centre de l'Aube disposal facility is designed to receive a many types of waste produced by nuclear power plants, reprocessing, decommissioning, as well as by the industry, hospitals and armed forces. The limitation of radioactive transfer to man and the limitation of personnel exposure in all situations considered plausible require limiting the total activity of the waste disposed in the facility as well as the activity of each package. The paper presents how ANDRA has derived the activity-related acceptance criteria, based on the safety analysis. In the French methodology, activity is considered as end-point for deriving the concentration limits per package, whereas it is the starting point for deriving the total activity limits. For the concentration limits (called here LMA) the approach consists of five steps: the determination of radionuclides important for safety with regards to operational and long-term safety, the use of relevant safety scenarios as a tool to derive quantitative limits, the setting of dose constraint per situation associated with scenarios, the setting of contribution factor per radionuclide, and the calculation of concentration activity limits. An exhaustive survey has been performed and has shown that the totality of waste packages which should be delivered by waste generators are acceptable in terms of activity limits in the Centre de l'Aube. Examples of concentration activity limits derived from this methodology are presented. Furthermore those limits have been accepted by the French regulatory body and

  9. Towards the development of workable acceptance criteria for the divertor CFC monoblock armour

    Energy Technology Data Exchange (ETDEWEB)

    D' Agata, E. [ITER International Team, ITER Joint Work Site, Boltzmannstr. 2, D-85748 Garching (Germany)]. E-mail: dagatae@itereu.de; Tivey, R. [ITER International Team, ITER Joint Work Site, Boltzmannstr. 2, D-85748 Garching (Germany)

    2005-11-15

    The plasma-facing components (PFCs) of the ITER divertor will be subjected to high heat flux (HHF). Carbon-fibre composite (CFC) is selected as the armour for the region of highest heat flux where the scrape-off layer of the plasma intercepts the vertical targets (VT). Failure of the armour to heat sink joints will compromise the performance of the divertor and could ultimately result in its failure and the shut down of the ITER machine. There are tens of thousands of CFCs to CuCrZr joints. The aim of the PFC design is to ensure that the divertor can continue to function even with the failure of a few joints. In preparation for writing the procurement specification for the ITER vertical target PFCs, a programme of work is underway with the objective of defining workable acceptance criteria for the PFC armour joints.

  10. Modeling Carbon Turnover in Five Terrestrial Ecosystems in the Boreal Zone Using Multiple Criteria of Acceptance

    International Nuclear Information System (INIS)

    Karlberg, Louise; Gustafsson, David; Jansson, Per-Erik

    2006-01-01

    Estimates of carbon fluxes and turnover in ecosystems are key elements in the understanding of climate change and in predicting the accumulation of trace elements in the biosphere. In this paper we present estimates of carbon fluxes and turnover times for five terrestrial ecosystems using a modeling approach. Multiple criteria of acceptance were used to parameterize the model, thus incorporating large amounts of multi-faceted empirical data in the simulations in a standardized manner. Mean turnover times of carbon were found to be rather similar between systems with a few exceptions, even though the size of both the pools and the fluxes varied substantially. Depending on the route of the carbon through the ecosystem, turnover times varied from less than one year to more than one hundred, which may be of importance when considering trace element transport and retention. The parameterization method was useful both in the estimation of unknown parameters, and to identify variability in carbon turnover in the selected ecosystems

  11. Towards the development of workable acceptance criteria for the divertor CFC monoblock armour

    International Nuclear Information System (INIS)

    D'Agata, E.; Tivey, R.

    2005-01-01

    The plasma-facing components (PFCs) of the ITER divertor will be subjected to high heat flux (HHF). Carbon-fibre composite (CFC) is selected as the armour for the region of highest heat flux where the scrape-off layer of the plasma intercepts the vertical targets (VT). Failure of the armour to heat sink joints will compromise the performance of the divertor and could ultimately result in its failure and the shut down of the ITER machine. There are tens of thousands of CFCs to CuCrZr joints. The aim of the PFC design is to ensure that the divertor can continue to function even with the failure of a few joints. In preparation for writing the procurement specification for the ITER vertical target PFCs, a programme of work is underway with the objective of defining workable acceptance criteria for the PFC armour joints

  12. Advances in flaw evaluation procedures and acceptance criteria for reactor piping

    International Nuclear Information System (INIS)

    Gamble, R.M.; Zahoor, A.; Norris, D.M.

    1986-01-01

    During the past several years, intergranular stress corrosion cracks (IGSCC) have been detected in stainless steel piping in boiling water reactors (BWRs) and have resulted in an increased number of flaw evaluations. To reduce the outage time associated with evaluating IGSCC, various research and ASME code groups have spent significant effort to provide utility personnel with efficient means to detect, classify, and size flaws, and to determine suitability for return to service for flawed stainless steel piping. One of the several nondestructive evaluation technologies that has received considerable attention is fracture mechanics, the discipline that considers the failure of flawed material. Fracture mechanics can be used to answer two key questions concerning return to service of flawed pipe: (a) what is the largest flaw size that can be returned to service and still maintain adequate safety margins at the applied loads, and (b) how much operating time remains before the crack reaches the largest allowable size? The purpose of this paper is to provide an overview of the recently developed ASME code Section XI flaw size evaluation procedure and acceptance criteria for stainless steel piping and their application by BWR owners to efficiently determine if flaws found by nondestructive examination are acceptable for continued service

  13. Advances in flaw evaluation procedures and acceptance criteria for reactor piping

    Energy Technology Data Exchange (ETDEWEB)

    Gamble, R.M.; Zahoor, A.; Norris, D.M.

    1986-01-01

    During the past several years, intergranular stress corrosion cracks (IGSCC) have been detected in stainless steel piping in boiling water reactors (BWRs) and have resulted in an increased number of flaw evaluations. To reduce the outage time associated with evaluating IGSCC, various research and ASME code groups have spent significant effort to provide utility personnel with efficient means to detect, classify, and size flaws, and to determine suitability for return to service for flawed stainless steel piping. One of the several nondestructive evaluation technologies that has received considerable attention is fracture mechanics, the discipline that considers the failure of flawed material. Fracture mechanics can be used to answer two key questions concerning return to service of flawed pipe: (a) what is the largest flaw size that can be returned to service and still maintain adequate safety margins at the applied loads, and (b) how much operating time remains before the crack reaches the largest allowable size. The purpose of this paper is to provide an overview of the recently developed ASME code Section XI flaw size evaluation procedure and acceptance criteria for stainless steel piping and their application by BWR owners to efficiently determine if flaws found by nondestructive examination are acceptable for continued service.

  14. Industry Application Emergency Core Cooling System Cladding Acceptance Criteria Early Demonstration

    Energy Technology Data Exchange (ETDEWEB)

    Szilard, Ronaldo H. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Youngblood, Robert W. [FPoliSolutions LLC, Murrysville, PA (United States); Zhang, Hongbin [Idaho National Lab. (INL), Idaho Falls, ID (United States); Zhao, Haihua [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bayless, Paul D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rabiti, Cristian [Idaho National Lab. (INL), Idaho Falls, ID (United States); Alfonsi, Andrea [Idaho National Lab. (INL), Idaho Falls, ID (United States); Smith, Curtis L. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Frepoli, Cesare [FPoliSolutions LLC, Murrysville, PA (United States); Yurko, Joseph P. [FPoliSolutions LLC, Murrysville, PA (United States); Swindlehurst, Gregg [GS Nuclear Consulting, Charlotte, NC (United States); Zoino, Angelo [Univ. of Rome Tor Vergata (Italy)

    2015-09-01

    The U. S. NRC is currently proposing rulemaking designated as “10 CFR 50.46c” to revise the loss-of-coolant-accident (LOCA)/emergency core cooling system (ECCS) acceptance criteria to include the effects of higher burnup on cladding performance as well as to address other technical issues. The NRC is also currently resolving the public comments with the final rule expected to be issued in April 2016. The impact of the final 50.46c rule on the industry may involve updating of fuel vendor LOCA evaluation models, NRC review and approval, and licensee submittal of new LOCA evaluations or re-analyses and associated technical specification revisions for NRC review and approval. The rule implementation process, both industry and NRC activities, is expected to take 4-6 years following the rule effective date. As motivated by the new rule, the need to use advanced cladding designs may be a result. A loss of operational margin may result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licensee cost as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. Consequently, there will be an increased focus on licensee decision making related to LOCA analysis to minimize cost and impact, and to manage margin. The proposed rule would apply to a light water reactor and to all cladding types.

  15. Criteria required for an acceptable point-of-care test for UTI detection: Obtaining consensus using the Delphi technique.

    Science.gov (United States)

    Weir, Nichola-Jane M; Pattison, Sally H; Kearney, Paddy; Stafford, Bob; Gormley, Gerard J; Crockard, Martin A; Gilpin, Deirdre F; Tunney, Michael M; Hughes, Carmel M

    2018-01-01

    Urinary Tract Infections (UTIs) are common bacterial infections, second only to respiratory tract infections and particularly prevalent within primary care. Conventional detection of UTIs is culture, however, return of results can take between 24 and 72 hours. The introduction of a point of care (POC) test would allow for more timely identification of UTIs, facilitating improved, targeted treatment. This study aimed to obtain consensus on the criteria required for a POC UTI test, to meet patient need within primary care. Criteria for consideration were compiled by the research team. These criteria were validated through a two-round Delphi process, utilising an expert panel of healthcare professionals from across Europe and United States of America. Using web-based questionnaires, panellists recorded their level of agreement with each criterion based on a 5-point Likert Scale, with space for comments. Using median response, interquartile range and comments provided, criteria were accepted/rejected/revised depending on pre-agreed cut-off scores. The first round questionnaire presented thirty-three criteria to the panel, of which 22 were accepted. Consensus was not achieved for the remaining 11 criteria. Following response review, one criterion was removed, while after revision, the remaining 10 criteria entered the second round. Of these, four were subsequently accepted, resulting in 26 criteria considered appropriate for a POC test to detect urinary infections. This study generated an approved set of criteria for a POC test to detect urinary infections. Criteria acceptance and comments provided by the healthcare professionals also supports the development of a multiplex point of care UTI test.

  16. Strain-based plastic instability acceptance criteria for ferritic steel safety class 1 nuclear components under level D

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ji Su; Lee, Han Sang; Kim, Yun Jae [Dept. of Mechanical Engineering, Korea University, Seoul (Korea, Republic of); Kim, Jong Sung [Dept. of Mechanical Engineering, Sunchon National University, Suncheon (Korea, Republic of); Kim, Jin Won [Dept. of Nuclear Engineering, Chosun University, Gwangju (Korea, Republic of)

    2015-04-15

    This paper proposes strain-based acceptance criteria for assessing plastic instability of the safety class 1 nuclear components made of ferritic steel during level D service loads. The strain-based criteria were proposed with two approaches: (1) a section average approach and (2) a critical location approach. Both approaches were based on the damage initiation point corresponding to the maximum load-carrying capability point instead of the fracture point via tensile tests and finite element analysis (FEA) for the notched specimen under uni-axial tensile loading. The two proposed criteria were reviewed from the viewpoint of design practice and philosophy to select a more appropriate criterion. As a result of the review, it was found that the section average approach is more appropriate than the critical location approach from the viewpoint of design practice and philosophy. Finally, the criterion based on the section average approach was applied to a simplified reactor pressure vessel (RPV) outlet nozzle subject to SSE loads. The application shows that the strain-based acceptance criteria can consider cumulative damages caused by the sequential loads unlike the stress-based acceptance criteria and can reduce the over conservatism of the stress-based acceptance criteria, which often occurs for level D service loads.

  17. Strain-based plastic instability acceptance criteria for ferritic steel safety class 1 nuclear components under level D

    International Nuclear Information System (INIS)

    Kim, Ji Su; Lee, Han Sang; Kim, Yun Jae; Kim, Jong Sung; Kim, Jin Won

    2015-01-01

    This paper proposes strain-based acceptance criteria for assessing plastic instability of the safety class 1 nuclear components made of ferritic steel during level D service loads. The strain-based criteria were proposed with two approaches: (1) a section average approach and (2) a critical location approach. Both approaches were based on the damage initiation point corresponding to the maximum load-carrying capability point instead of the fracture point via tensile tests and finite element analysis (FEA) for the notched specimen under uni-axial tensile loading. The two proposed criteria were reviewed from the viewpoint of design practice and philosophy to select a more appropriate criterion. As a result of the review, it was found that the section average approach is more appropriate than the critical location approach from the viewpoint of design practice and philosophy. Finally, the criterion based on the section average approach was applied to a simplified reactor pressure vessel (RPV) outlet nozzle subject to SSE loads. The application shows that the strain-based acceptance criteria can consider cumulative damages caused by the sequential loads unlike the stress-based acceptance criteria and can reduce the over conservatism of the stress-based acceptance criteria, which often occurs for level D service loads.

  18. Manufacturing and testing of reference samples for the definition of acceptance criteria for the ITER divertor

    International Nuclear Information System (INIS)

    Visca, Eliseo; Cacciotti, E.; Libera, S.; Mancini, A.; Pizzuto, A.; Roccella, S.; Riccardi, B.; Escourbiac, F.; Sanguinetti, G.P.

    2010-01-01

    The most critical part of a high heat flux (HHF) plasma facing component (PFC) is the armour to heat sink joint. An experimental study was launched by EFDA in order to define the acceptance criteria to be used for the procurements of the ITER Divertor PFCs. ENEA is involved in the European International Thermonuclear Experimental Reactor (ITER) R and D activities and together with Ansaldo Ricerche S.p.A. has manufactured several PFCs mock-ups using the Hot Radial Pressing and Pre-Brazed Casting technologies. According to the technical specifications issued by EFDA, ENEA and Ansaldo have collaborated to manufacture half of the samples with calibrated artificial defects required for this experimental study. After manufacturing, the samples were examined by ultrasonic and SATIR non-destructive examination (NDE) methods in order to confirm the size and position of the artificial defects. In particular, it was concluded that defects are detectable with these NDE techniques and they finally gave indication about the threshold of propagation during high heat flux experiments relevant with heat fluxes expected in ITER Divertor. This paper reports the manufacturing procedure used to obtain the required calibrated artificial defects in the CFC and W armoured samples as well as the NDE results and the thermal high heat flux results.

  19. Experimental activity on the definition of acceptance criteria for the ITER divertor plasma facing components

    International Nuclear Information System (INIS)

    Escourbiac, F.; Constans, S.; Vignal, N.; Cantone, V.; Richou, M.; Durocher, A.; Riccardi, B.; Bobin, I.; Jouvelot, J.L.; Merola, M.

    2009-01-01

    Tens of thousands of armor/heat sink joints will be produced by the industry during the manufacturing of ITER divertor PFC, statistically, there is a probability that joints with defects be delivered. The purpose of this paper is to study the detection and evolution during operation of calibrated defects artificially implemented on samples, as an experimental basis for the definition of acceptance criteria for the bond armor/heat sink in the frame of industrial manufacturing conditions.It was found that current CFC monoblock design option was compatible with the heat loads specified at the lower part of the vertical target (up to 20 MW/m 2 ), including the presence of armor/heat sink defects (up to 50 deg. extension for a location at 0 deg. or 45 deg.) detectable with NDE techniques developed in Europe (US, SATIR). The current W monoblock design appeared suitable for the upper part of the vertical target with defects extension up to 50 deg. but is not adapted for heat flux of 20 MW/m 2 . The studied W flat tile design proved to be compatible with fluxes of 5 MW/m 2 but unable to sustain cycling fluxes of 10 MW/m 2 .

  20. Simplified probabilistic approach to determine safety factors in deterministic flaw acceptance criteria

    International Nuclear Information System (INIS)

    Barthelet, B.; Ardillon, E.

    1997-01-01

    The flaw acceptance rules in nuclear components rely on deterministic criteria supposed to ensure the safe operating of plants. The interest of having a reliable method of evaluating the safety margins and the integrity of components led Electricite de France to launch a study to link safety factors with requested reliability. A simplified analytical probabilistic approach is developed to analyse the failure risk in Fracture Mechanics. Assuming lognormal distributions of the main random variables, it is possible considering a simple Linear Elastic Fracture Mechanics model, to determine the failure probability as a function of mean values and logarithmic standard deviations. The 'design' failure point can be analytically calculated. Partial safety factors on the main variables (stress, crack size, material toughness) are obtained in relation with reliability target values. The approach is generalized to elastic plastic Fracture Mechanics (piping) by fitting J as a power law function of stress, crack size and yield strength. The simplified approach is validated by detailed probabilistic computations with PROBAN computer program. Assuming reasonable coefficients of variations (logarithmic standard deviations), the method helps to calibrate safety factors for different components taking into account reliability target values in normal, emergency and faulted conditions. Statistical data for the mechanical properties of the main basic materials complement the study. The work involves laboratory results and manufacture data. The results of this study are discussed within a working group of the French in service inspection code RSE-M. (authors)

  1. Manufacturing and testing of reference samples for the definition of acceptance criteria for the ITER divertor

    Energy Technology Data Exchange (ETDEWEB)

    Visca, Eliseo, E-mail: visca@frascati.enea.i [Associazione EURATOM-ENEA sulla Fusione, Frascati (Italy); Cacciotti, E.; Libera, S.; Mancini, A.; Pizzuto, A.; Roccella, S. [Associazione EURATOM-ENEA sulla Fusione, Frascati (Italy); Riccardi, B., E-mail: Bruno.Riccardi@f4e.europa.e [Fusion For Energy, Barcelona (Spain); Escourbiac, F., E-mail: frederic.escourbiac@iter.or [ITER Organization, Cadarache (France); Sanguinetti, G.P., E-mail: gianpaolo.sanguinetti@aen.ansaldo.i [Ansaldo Energia S.p.A., Genova (Italy)

    2010-12-15

    The most critical part of a high heat flux (HHF) plasma facing component (PFC) is the armour to heat sink joint. An experimental study was launched by EFDA in order to define the acceptance criteria to be used for the procurements of the ITER Divertor PFCs. ENEA is involved in the European International Thermonuclear Experimental Reactor (ITER) R and D activities and together with Ansaldo Ricerche S.p.A. has manufactured several PFCs mock-ups using the Hot Radial Pressing and Pre-Brazed Casting technologies. According to the technical specifications issued by EFDA, ENEA and Ansaldo have collaborated to manufacture half of the samples with calibrated artificial defects required for this experimental study. After manufacturing, the samples were examined by ultrasonic and SATIR non-destructive examination (NDE) methods in order to confirm the size and position of the artificial defects. In particular, it was concluded that defects are detectable with these NDE techniques and they finally gave indication about the threshold of propagation during high heat flux experiments relevant with heat fluxes expected in ITER Divertor. This paper reports the manufacturing procedure used to obtain the required calibrated artificial defects in the CFC and W armoured samples as well as the NDE results and the thermal high heat flux results.

  2. Development of performance assessment methodology for establishment of quantitative acceptance criteria of near-surface radioactive waste disposal

    Energy Technology Data Exchange (ETDEWEB)

    Kim, C. R.; Lee, E. Y.; Park, J. W.; Chang, G. M.; Park, H. Y.; Yeom, Y. S. [Korea Hydro and Nuclear Power Co., Ltd., Seoul (Korea, Republic of)

    2002-03-15

    The contents and the scope of this study are as follows : review of state-of-the-art on the establishment of waste acceptance criteria in foreign near-surface radioactive waste disposal facilities, investigation of radiological assessment methodologies and scenarios, investigation of existing models and computer codes used in performance/safety assessment, development of a performance assessment methodology(draft) to derive quantitatively radionuclide acceptance criteria of domestic near-surface disposal facility, preliminary performance/safety assessment in accordance with the developed methodology.

  3. Evaluation of ISDP Batch 2 Qualification Compliance to 512-S, DWPF, Tank Farm, and Saltstone Waste Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Shafer, A.

    2010-05-05

    The purpose of this report is to document the acceptability of the second macrobatch (Salt Batch 2) of Tank 49H waste to H Tank Farm, DWPF, and Saltstone for operation of the Interim Salt Disposition Project (ISDP). Tank 49 feed meets the Waste Acceptance Criteria (WAC) requirements specified by References 11, 12, and 13. Salt Batch 2 material is qualified and ready to be processed through ARP/MCU to the final disposal facilities.

  4. The revision of RP 91 on criteria for acceptability of radiological (including radiotherapy) and nuclear medicine installations

    International Nuclear Information System (INIS)

    Faulkner, K.; Malone, J. F.; Christofides, S.; Lillicrap, S.; Horton, P.

    2013-01-01

    In 1997 the European Commission published Radiation Protection 91: 'Criteria for acceptability of radiological (including radiotherapy) and nuclear medicine installations'(1). This document specified the minimum criteria for acceptability. It has been used to this effect in legislation, codes of practice and by individual professionals. In a single document, it defined a level of performance at which remedial action was required. The document specified a series of parameters which characterised equipment performance and acceptable levels of performance. In its time it proved to be a useful document which was applied in member states to various degrees. Since the publication of Report 91 in 1997(1), a series of weaknesses emerged over time. Development of new radiological systems and technologies, as well as improvements in traditional technologies, has created circumstances where the acceptability criteria were in need of review. These weaknesses were recognised by the European Commission and a tender for its revision was issued. The criteria were developed by a team drawn from a broad range of backgrounds including hospitals, industry, government bodies, regulators and standardisation organisations. Representatives were mainly from Europe, but individuals from the American Association of Physicists in Medicine and International Atomic Energy Agency were included in the drafting process. This study describes the process employed in developing the revised document and the consultation process involved. One of the major difficulties the revision team encountered was related to an understanding of the actual meaning of the EC Directive(2). The view taken by the revision team was that Article 8, paragraph 3 places responsibilities on both the holders of radiological equipment and competent authorities. The acceptability criteria have been produced consistent with the European Commission's Medical Exposures Directive(2), which requires that patient exposures are

  5. Study of waste acceptance criteria for low-level radioactive waste from medical, industrial, and research facilities (Contract research)

    International Nuclear Information System (INIS)

    Koibuchi, Hiroto; Dohi, Terumi; Ishiguro, Hideharu; Hayashi, Masaru; Senda, Masaki

    2008-12-01

    Japan Atomic Energy Agency (JAEA) is supposed to draw up the plan for the disposal program of the very low-level radioactive waste and low-level radioactive waste generated from medical, industrial and research facilities. For instance, there are these facilities in JAEA, universities, private companies, and so on. JAEA has to get to know about the waste and its acceptance of other institutions described above because it is important for us to hold the licenses for the disposal program regarding safety assessment. This report presents the basic data concerning radioactive waste of research institutes etc. except RI waste, domestic and foreign information related to acceptance criteria for disposal of the low-level radioactive waste, the current status of foreign medical waste management, waste acceptance, and such. In this report, Japan's acceptance criteria were summarized on the basis of present regulation. And, the criteria of foreign countries, United States, France, United Kingdom and Spain, were investigated by survey of each reference. In addition, it was reported that the amount of waste from laboratories etc. for near-surface disposal and their characterization in our country. The Subjects of future work: the treatment of hazardous waste, the problem of the double-regulation (the Nuclear Reactor Regulation Law and the Law Concerning Prevention from Radiation Hazards due to Radioisotopes and Others) and the possession of waste were discussed here. (author)

  6. Are regulation-driven performance criteria still acceptable? - The German point of view.

    Science.gov (United States)

    Orth, Matthias

    2015-05-01

    Performance criteria should be a challenge for the laboratories to improve their quality. In countries with mandatory proficiency testing, the definition of performance criteria is a particular issue. If the definition of performance criteria is mandated from the regulatory bodies to medico-scientific institutions, scientific approaches (i.e., based on biological variation), the state-of-the-art approach (i.e., based on technical feasibility) as well as medical needs can be used to set up performance criteria such as the Richtlinie der Bundesärztekammer (RiliBÄK; Guideline of the German Medical Association on Quality Assurance in Medical Laboratory Examinations) in Germany. The experiences with RiliBÄK show that these performance criteria have to be revised on an ongoing basis.

  7. Acceptability criteria for linear dependence in validating UV-spectrophotometric methods of quantitative determination in forensic and toxicological analysis

    Directory of Open Access Journals (Sweden)

    L. Yu. Klimenko

    2014-08-01

    Full Text Available Introduction. This article is the result of authors’ research in the field of development of the approaches to validation of quantitative determination methods for purposes of forensic and toxicological analysis and devoted to the problem of acceptability criteria formation for validation parameter «linearity/calibration model». The aim of research. The purpose of this paper is to analyse the present approaches to acceptability estimation of the calibration model chosen for method description according to the requirements of the international guidances, to form the own approaches to acceptability estimation of the linear dependence when carrying out the validation of UV-spectrophotometric methods of quantitative determination for forensic and toxicological analysis. Materials and methods. UV-spectrophotometric method of doxylamine quantitative determination in blood. Results. The approaches to acceptability estimation of calibration models when carrying out the validation of bioanalytical methods is stated in international papers, namely «Guidance for Industry: Bioanalytical method validation» (U.S. FDA, 2001, «Standard Practices for Method Validation in Forensic Toxicology» (SWGTOX, 2012, «Guidance for the Validation of Analytical Methodology and Calibration of Equipment used for Testing of Illicit Drugs in Seized Materials and Biological Specimens» (UNODC, 2009 and «Guideline on validation of bioanalytical methods» (ЕМА, 2011 have been analysed. It has been suggested to be guided by domestic developments in the field of validation of analysis methods for medicines and, particularly, by the approaches to validation methods in the variant of the calibration curve method for forming the acceptability criteria of the obtained linear dependences when carrying out the validation of UV-spectrophotometric methods of quantitative determination for forensic and toxicological analysis. The choice of the method of calibration curve is

  8. Acceptance criteria for non-destructive examination of double-shell tanks

    International Nuclear Information System (INIS)

    Jensen, C.E.

    1995-09-01

    This supporting document provides requirements for acceptance of relevant indications found during non-destructive examination of double-shell tanks (DSTs) at Hanford 200 areas. Requirements for evaluation of relevant indications are provided to determine acceptability of continued safe operation of the DSTs. Areas of the DSTs considered include the tank wall vapor space, liquid-vapor interface, wetted tank wall, sludge-liquid interface, and the knuckle region

  9. Preliminary waste acceptance criteria for the ICPP spent fuel and waste management technology development program

    International Nuclear Information System (INIS)

    Taylor, L.L.; Shikashio, R.

    1993-09-01

    The purpose of this document is to identify requirements to be met by the Producer/Shipper of Spent Nuclear Fuel/High-LeveL Waste SNF/HLW in order for DOE to be able to accept the packaged materials. This includes defining both standard and nonstandard waste forms

  10. Acceptance criteria for the evaluation of Category 1 fuel cycle facility physical security plans

    Energy Technology Data Exchange (ETDEWEB)

    Dwyer, P.A.

    1991-10-01

    This NUREG document presents criteria developed from US Nuclear Regulatory Commission regulations for the evaluation of physical security plans submitted by Category 1 fuel facility licensees. Category 1 refers to those licensees who use or possess a formula quantity of strategic special nuclear material.

  11. Acceptance criteria for the evaluation of Category 1 fuel cycle facility physical security plans

    International Nuclear Information System (INIS)

    Dwyer, P.A.

    1991-10-01

    This NUREG document presents criteria developed from US Nuclear Regulatory Commission regulations for the evaluation of physical security plans submitted by Category 1 fuel facility licensees. Category 1 refers to those licensees who use or possess a formula quantity of strategic special nuclear material

  12. Acceptance criteria for reprocessed AcuNav catheters: comparison between functionality testing and clinical image assessment.

    Science.gov (United States)

    Bank, Alan J; Berry, James M; Wilson, Robert F; Lester, Bruce R

    2009-03-01

    The AcuNav-catheter is a vector-phased array ultrasound catheter that has shown great utility for both diagnosis and electrophysiological interventions. To test the feasibility of limited catheter reuse and to ensure that reprocessed catheters would produce acceptable clinical images, the present study compared the 2-D and Doppler image quality, as determined by clinical assessment, with the catheter's functional status as determined by the FirstCall 2000 transducer tester. Reprocessed catheters from four functional categories, two acceptable and two unacceptable, were used to collect images, 2-D and Doppler, from a porcine heart. The images were blinded and then rated by clinical evaluation. The study found that catheter images from all functional categories were found to be clinically acceptable except for those from the lowest unacceptable category. In addition, examination of tip deflection characteristics showed no significant difference between new and reprocessed catheters. We conclude that reprocessed AcuNav catheters that pass functional tests are able to produce clinical images, 2-D and Doppler, which are equivalent to their new counterparts.

  13. Upgraded acceptance criteria from transient thermography control for the W7-X divertor target elements

    Energy Technology Data Exchange (ETDEWEB)

    Missirlian, M. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France)], E-mail: marc.missirlian@cea.fr; Boscary, J. [Max-Planck-Institut fuer Plasmaphysik, Euratom Association, Boltzmannstr. 2, D-85748 Garching (Germany); Guigon, R.; Schlosser, J.; Durocher, A. [CEA, IRFM, F-13108 Saint-Paul-Lez-Durance (France); Greuner, H. [Max-Planck-Institut fuer Plasmaphysik, Euratom Association, Boltzmannstr. 2, D-85748 Garching (Germany)

    2009-06-15

    The commissioning of plasma-facing component fields needs advanced non-destructive methods to detect in a reliable way the defects, which can impair the component performances and/or integrity during operation. Within this framework, CEA developed a dedicated non-destructive examination method based on active infrared thermography (SATIR facility) to inspect the bonding between armour material and metallic heat sink. Used with successful in the commissioning of the toroidal pump limiter of Tore Supra, this technique was applied in the frame of the pre-series activities of the Wendelstein 7-X high heat flux divertor elements to assess the bonding quality of the delivered components. This paper presents the methodology adopted to define an acceptance criterion based on SATIR test bed possibly applied for a serial inspection of the Wendelstein 7-X elements. Using the well-tried acceptance test based on the DTref{sub m}ax parameter, the new method includes advanced data post-processing techniques from thermo-signal SATIR and a data merging method to help the decision-making and to optimise the reliability of the binary response expected for a final decision in terms of acceptance test.

  14. Upgraded acceptance criteria from transient thermography control for the W7-X divertor target elements

    International Nuclear Information System (INIS)

    Missirlian, M.; Boscary, J.; Guigon, R.; Schlosser, J.; Durocher, A.; Greuner, H.

    2009-01-01

    The commissioning of plasma-facing component fields needs advanced non-destructive methods to detect in a reliable way the defects, which can impair the component performances and/or integrity during operation. Within this framework, CEA developed a dedicated non-destructive examination method based on active infrared thermography (SATIR facility) to inspect the bonding between armour material and metallic heat sink. Used with successful in the commissioning of the toroidal pump limiter of Tore Supra, this technique was applied in the frame of the pre-series activities of the Wendelstein 7-X high heat flux divertor elements to assess the bonding quality of the delivered components. This paper presents the methodology adopted to define an acceptance criterion based on SATIR test bed possibly applied for a serial inspection of the Wendelstein 7-X elements. Using the well-tried acceptance test based on the DTref m ax parameter, the new method includes advanced data post-processing techniques from thermo-signal SATIR and a data merging method to help the decision-making and to optimise the reliability of the binary response expected for a final decision in terms of acceptance test.

  15. Radioactive waste management: review on clearance levels and acceptance criteria legislation, requirements and standards.

    Science.gov (United States)

    Maringer, F J; Suráň, J; Kovář, P; Chauvenet, B; Peyres, V; García-Toraño, E; Cozzella, M L; De Felice, P; Vodenik, B; Hult, M; Rosengård, U; Merimaa, M; Szücs, L; Jeffery, C; Dean, J C J; Tymiński, Z; Arnold, D; Hinca, R; Mirescu, G

    2013-11-01

    In 2011 the joint research project Metrology for Radioactive Waste Management (MetroRWM)(1) of the European Metrology Research Programme (EMRP) started with a total duration of three years. Within this project, new metrological resources for the assessment of radioactive waste, including their calibration with new reference materials traceable to national standards will be developed. This paper gives a review on national, European and international strategies as basis for science-based metrological requirements in clearance and acceptance of radioactive waste. © 2013 Elsevier Ltd. All rights reserved.

  16. Mark II containment lead plant program load evaluation and acceptance criteria

    International Nuclear Information System (INIS)

    1978-10-01

    The report, prepared by the Office of Nuclear Reactor Regulation, addresses the portion of the Mark II owner's program that provides a generic methodology for establishing design basis LOCA and safety relief valve loads for the lead Mark II facilities (Zimmer, Shoreham, and LaSalle), i.e., the lead plant program. The report includes an evaluation of the Mark II owner's load methodology, a description of load methodologies that we find acceptable for use in the individual plant unique assessments, and the basis for the stated conclusions

  17. Processing of Irradiated Graphite to Meet Acceptance Criteria for Waste Disposal. Results of a Coordinated Research Project

    International Nuclear Information System (INIS)

    2016-05-01

    Graphite is widely used in the nuclear industry and in research facilities and this has led to increasing amounts of irradiated graphite residing in temporary storage facilities pending disposal. This publication arises from a coordinated research project (CRP) on the processing of irradiated graphite to meet acceptance criteria for waste disposal. It presents the findings of the CRP, the general conclusions and recommendations. The topics covered include, graphite management issues, characterization of irradiated graphite, processing and treatment, immobilization and disposal. Included on the attached CD-ROM are formal reports from the participants

  18. New contact boiling experiments to evaluate Calandria tube strain acceptance criteria

    Energy Technology Data Exchange (ETDEWEB)

    El-Hawary, M.; Szymanski, J.; Tanase, A.; Delja, A.; Oussoren, A., E-mail: Magdy.El-Hawary@cnsc-ccsn.gc.ca [Canadian Nuclear Safety Comission, Ottawa, ON (Canada); Neal, P. [Canadian Nuclear Laboratories, Chalk River, ON (Canada)

    2015-07-01

    The Canadian Nuclear Safety Commission(CNSC) has contracted the Canadian Nuclear Laboratories(CNL) to conduct additional Contact Boiling (CB) experiments with the main objective of evaluating the acceptance criterion of CalandriaTube (CT) strain limit of 2%, proposed by the industry for fuel channel integrity assessments. The test conditions are selected using analytical tools and guidance from existing CANDU Owners Group (COG) test results, so as to lead to CT strain close to this value. The experiments will also be used to evaluate the CT quench temperature correlation proposed. This paper presents conditions selected for the first three experiments, their most important results and their preliminary analysis, with a focus on the test which produced CT strain in excess of 2%. (author)

  19. Flaw acceptance criteria taking into consideration the NDT: radiographic and ultrasonic testing. Analysis through the fracture mechanics methods

    International Nuclear Information System (INIS)

    Capurro, E.; Alicino, F.; Corvi, A.

    1993-01-01

    The present study compares and evaluates the flaw acceptance criteria of the non-destructive inspections meeting European Community standards, through the application of the fracture mechanics methods that were determined and verified by the previous activity. Some choices were made; these, however, do not change the general validity of the conclusions. Shaved full-penetration butt welds of Class 1 components making up the primary circuit were considered and the following parameters varied: standards: French, German, Italian (ASME III) and UK; material: AISI 316 and low alloy steel A 533; base material and weld metal; temperature: RT, 370 deg C for the austenitic and 260 deg C for the ferritic steel; ultrasonic and radiographic methods; defect position: surface and internal; stress condition: situations with different primary and secondary stresses. From a preliminary examination of this study it is evident that the large quantity of results available and the abundance of information contained therein make a simple and exhaustive synthesis difficult. In fact, different analyses are possible and we have, therefore, limited the research to activities to perform a comparison and a general evaluation of the acceptance criteria of the non-destructive testing. (authors). 57 refs., 25 figs., 11 tabs

  20. The Insulation for Machines Having a High Lifespan Expectancy, Design, Tests and Acceptance Criteria Issues

    Directory of Open Access Journals (Sweden)

    Olivier Barré

    2017-02-01

    Full Text Available The windings insulation of electrical machines will remain a topic that is updated frequently. The criteria severity requested by the electrical machine applications increases continuously. Manufacturers and designers are always confronted with new requirements or new criteria with enhanced performances. The most problematic requirements that will be investigated here are the extremely long lifespan coupled to critical operating conditions (overload, supply grid instabilities, and critical operating environments. Increasing lifespan does not have a considerable benefit because the purchasing price of usual machines has to be compared to the purchasing price and maintenance price of long lifespan machines. A machine having a 40-year lifespan will cost more than twice the usual price of a 20-year lifetime machine. Systems which need a long lifetime are systems which are crucial for a country, and those for which outage costs are exorbitant. Nuclear power stations are such systems. It is certain that the used technologies have evolved since the first nuclear power plant, but they cannot evolve as quickly as in other sectors of activities. No-one wants to use an immature technology in such power plants. Even if the electrical machines have exceeded 100 years of age, their improvements are linked to a patient and continuous work. Nowadays, the windings insulation systems have a well-established structure, especially high voltage windings. Unfortunately, a high life span is not only linked to this result. Several manufacturers’ improvements induced by many years of experiment have led to the writing of standards that help the customers and the manufacturers to regularly enhance the insulation specifications or qualifications. Hence, in this publication, the authors will give a step by step exhaustive review of one insulation layout and will take time to give a detailed report on the standards that are linked to insulation systems. No standard can

  1. Acceptance criteria for interim dry storage of aluminum-clad fuels

    International Nuclear Information System (INIS)

    Sindelar, R.L.; Peacock, H.B. Jr.; Iyer, N.C.; Louthan, M.R. Jr.

    1994-01-01

    Direct repository disposal of foreign and domestic research reactor fuels owned by the United States Department of Energy is an alternative to reprocessing (together with vitrification of the high level waste and storage in an engineered barrier) for ultimate disposition. Neither the storage systems nor the requirements and specifications for acceptable forms for direct repository disposal have been developed; therefore, an interim storage strategy is needed to safely store these fuels. Dry storage (within identified limits) of the fuels received from wet-basin storage would avoid excessive degradation to assure post-storage handleability, a full range of ultimate disposal options, criticality safety, and provide for maintaining confinement by the fuel/clad system. Dry storage requirements and technologies for US commercial fuels, specifically zircaloy-clad fuels under inert cover gas, are well established. Dry storage requirements and technologies for a system with a design life of 40 years for dry storage of aluminum-clad foreign and domestic research reactor fuels are being developed by various groups within programs sponsored by the DOE

  2. Criteria for acceptance to preprofessional dietetics programs vs desired qualities of professionals: an analysis.

    Science.gov (United States)

    Moore, K K

    1995-01-01

    The objectives of this analysis were to examine the literature and compare and contrast (a) qualities preferred in preprofessional dietetics students by directors of internships and approved preprofessional practice programs (AP4s), (b) characteristics needed to succeed in a scientific field, (c) traits emphasized by dietetics training programs compared with those most valued by employers, (d) skills needed by high-level managerial dietitians and those in business and communications, and (e) qualities dietitians have aspired to develop for increased competitiveness in the marketplace. Even though the revised Standards of Education have been in place since 1988, recent evaluation of criteria for internship and AP4 admission has shown traditional emphasis on academic performance and the importance of work experience. Success in scientific pursuits has been linked with more than innate intelligence; a drive for success and enthusiasm for learning are also involved. Internships foster mostly technical learning, so development of skills in human and conceptual areas are somewhat lacking. These skills, which have been identified as valuable to employers, need greater development or more consistent identification in the selection and training process. Perhaps serious consideration should be given to applicants for preprofessional programs who have shown leadership qualities through extracurricular activities or who have given themselves the opportunity to develop and improve these skills. Such students might hasten the metamorphosis of dietetics practitioners toward improved levels of compensation and professional fulfillment.

  3. Ammunition Peculiar Equipment (APE) 1995, NIR Propellant Analyzer, to MIL-STD-398, Military Standard Shields, Operational for Ammunition Operations, Criteria for Design of and Tests for Acceptance

    National Research Council Canada - National Science Library

    2003-01-01

    ... (SJMAC-DEM) to test the Ammunition Peculiar Equipment (APE) 1995 NIR Propellant Analyzer, to MIL-STD-398, "Military Standard Shields, Operational for Ammunition Operations, Criteria for Design of and Tests for Acceptance...

  4. R&D Plan for RISMC Industry Application #1: ECCS/LOCA Cladding Acceptance Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Szilard, Ronaldo Henriques [Idaho National Lab. (INL), Idaho Falls, ID (United States); Zhang, Hongbin [Idaho National Lab. (INL), Idaho Falls, ID (United States); Epiney, Aaron Simon [Idaho National Lab. (INL), Idaho Falls, ID (United States); Tu, Lei [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-04-01

    The Nuclear Regulatory Commission (NRC) is finalizing a rulemaking change that would revise the requirements in 10 CFR 50.46. In the proposed new rulemaking, designated as 10 CFR 50.46c, the NRC proposes a fuel performance-based equivalent cladding reacted (ECR) criterion as a function of cladding hydrogen content before the accident (pre-transient) in order to include the effects of higher burnup on cladding performance as well as to address other technical issues. A loss of operational margin may result due to the more restrictive cladding embrittlement criteria. Initial and future compliance with the rule may significantly increase vendor workload and licensee costs as a spectrum of fuel rod initial burnup states may need to be analyzed to demonstrate compliance. The Idaho National Laboratory (INL) has initiated a project, as part of the DOE Light Water Reactor Sustainability Program (LWRS), to develop analytical capabilities to support the industry in the transition to the new rule. This project is called the Industry Application 1 (IA1) within the Risk-Informed Safety Margin Characterization (RISMC) Pathway of LWRS. The general idea behind the initiative is the development of an Integrated Evaluation Model (IEM). The motivation is to develop a multiphysics framework to analyze how uncertainties are propagated across the stream of physical disciplines and data involved, as well as how risks are evaluated in a LOCA safety analysis as regulated under 10 CFR 50.46c. This IEM is called LOTUS which stands for LOCA Toolkit for US, and it represents the LWRS Program’s response to the proposed new rule making. The focus of this report is to complete an R&D plan to describe the demonstration of the LOCA/ECCS RISMC Industry Application # 1 using the advanced RISMC Toolkit and methodologies. This report includes the description and development plan for a RISMC LOCA tool that fully couples advanced MOOSE tools already in development in order to characterize and optimize

  5. Present state of the design and realization of regional radioactive waste depositories and waste acceptance criteria for disposal

    International Nuclear Information System (INIS)

    Kortus, J.

    1988-01-01

    Surface type regional depositories for radioactive wastes from nuclear power plants are described in detail. The depository of the Mochovce nuclear power plant is located near the plant, that of the Dukovany nuclear power plant is directly on the premises of the plant. Particular attention is paid to the design of the monolithic reinforced concrete pits, draining of rainwater from their surface, draining of seeping rainwater from the pit environment by means of a double drainage system, and insulation of the pits against water. The construction of the Mochovce depository started in 1987; some experience gained from this activity is presented. The radioactive waste acceptance criteria for depositories of this kind, based on safety analysis, are given. (author). 2 figs

  6. Final report on a study of coherence in acceptability criteria for the technical aspects of risks associated with potentially hazardous installations

    International Nuclear Information System (INIS)

    Chicken, J.C.

    1988-01-01

    This report describes the results of the study that was made, under Contract No ECI-1390-B7221-85D, for the European Atomic Energy Community. The aim of the study was to examine and assess the feasibility of developing coherent and uniform criteria for judging the acceptability of the technical aspects of the risks associated with potentially hazardous installations. The report is arranged in five main parts. First the nature of hazardous installations is considered and this provides the basis for examination of the currently-used technical risk acceptability criteria. Next, the possible forms of criteria are explored and then universally consistent partial and overall technical risk acceptability criteria are proposed. Following this the implications of using the criteria proposed at the design, regulatory and operating levels are examined. Then, by testing the criteria against some real decisions, the practical problems of using the proposed criteria are explored. This leads to consideration of possible alternatives to the proposed criteria. Finally the conclusions that appear to be justified are summarized and the need for further work is identified

  7. Proposed approach to derivation of acceptance criteria for disposal of disused sealed sources mixed with other accepted wastes in near-surface repository

    International Nuclear Information System (INIS)

    Salzer, P.; Stefula, V.; Homola, J.

    2003-01-01

    The Mochovce repository is described in the report. It is vault type near surface repository with 80 concrete vaults (2x2x20), 90 FRC containers (3.1 m 3 ) in one vault (3x10x3), compacted clay bath-tub around double row. 300 years of institutional control are envisioned.The following scenarios are examined: Normal evolution scenario; Alternative evolution scenarios (perforated clay barrier; well in close proximity); Intruder scenarios (construction of simple dwelling; construction of multi-storey building; construction of road; residence scenario). It is being proposed that the DSSs are disposed of in the containers together with normal operational waste. Long-lived alpha emitters - excluded a priori (e.g. 226 Ra); Short-lived (T 1/2 = 10 2 days) radionuclides - interim stored until decayed down to clearance level 60 Co - no activity limit, with due consideration of operational safety. The DSSs disposal issue is thus reduced to the disposal of 137 Cs. No limit has been imposed on total activity. Existing limits for operational waste: 3.13.10 13 Bq / container in the upper layer; 3.41.10 13 Bq / container in the bottom or intermediate layer. The acceptance criteria are assessed according to the risk. Two are models set up in MicroShield ver. 5.0. Homogenous source of 137 Cs in cubic concrete container and point source (hot spot) of the same activity. The result is - dose from the point source is 16.6 times higher than the one from the cube. As a result the following new restrictions arise for disposal of the 137 Cs spent industrial sources: disposal of DSSs is forbidden in the upper layer of the containers; maximum activity of the 137 Cs disused industrial source emplaced into the FRC container is 3.41x10 13 / 16.6 = 2.05x10 12 Bq in case of FRC filling by non-radioactive cement mortar; if the cemented radioactive waste is to be used for filling of FRC, decrease of the limit for the disused sealed source is equivalent to the radioactivity of the cement mixture

  8. A research for Class II defect Bored Pile’s Accept Criteria: A case of Penang Second Marine bridge

    Science.gov (United States)

    Huang, Kang

    2018-03-01

    The aim of this preliminary research is to study the accept criteria of class II bored pile with subtle defect. According to a detailed comparison of the existed different standards, Chinese ones are more applicable especially for the large diameter bored piles. Through the concrete coring at pile No P25-03 of this case and the comparison to the actual calculation, the Class II pile’s defects were very minor. Comparison was also made for the effects on pile structural capacities before and after repair of the defects. the feasible repair proposal may bring forward to more defects to the piles. The Class II piles don’t need any further repairation when piles have typical of similar character and sonic logging test result with P25-03‘s one. For other Class II piles with some differences in characters, verification is needed through further concrete coring on the pile. The recommendation of this research could be adopted for the similar huge marine structures which installed large diameter bored piles.

  9. Measurement methodology for fulfilling of waste acceptance criteria for low and intermediate level radioactive waste in storages - 59016

    International Nuclear Information System (INIS)

    Sokcic-Kostic, M.; Langer, F.; Schultheis, R.

    2012-01-01

    Low and intermediate level radioactive waste must be sorted and treated before it can be sent to radioactive waste storage. The waste must fulfil an extensive amount of acceptance criteria (WAC) to guarantee a safe storage period. NUKEM Technologies has a broad experience with the building and management of radioactive waste treatment facilities and has developed methods and equipment to produce the waste packages and to gather all the required information. In this article we consider low and intermediate level radioactive waste excluding nuclear fuel material, even fresh fuel with low radiation. Only solid radioactive waste (RAW) will be considered. (Liquid RAW is usually processed and solidified before storage. Exception is the reprocessing of nuclear fuel.) Low and intermediate level radioactive waste has to be kept in storage facilities until isotopes are decayed sufficiently and the waste can be released. The storage has to fulfil certain conditions regarding the possible radiological impact and the possible chemical impact on the environment. With the inventory of nuclear waste characterised, the radiological impact can be estimated. RAW mainly originates from the operation of nuclear power plants. A small amount comes from reprocessing installations or from research entities. Chemical safety aspects are of qualitative nature, excluding substances in whole but not compared to limit values. Therefore they have minor influence on the storage conditions. Hereby corrosion and immobilisation of the waste play important roles. The storage concept assumes that the waste will be released if the radioactivity has decreased to an acceptable level. NUKEM Technologies has been specialised on collecting all data needed for the fulfilling of waste acceptance criteria (WAC). The classification as low or intermediate level waste is made on base of surface dose rate of the waste package as well as on the mass specific beta activity. Low level waste must not include isotopes

  10. Structural acceptance criteria for the evaulation of existing double-shell waste storage tanks located at the Hanford site, Richland, Washington

    International Nuclear Information System (INIS)

    Julyk, L.J.; Day, A.D.; Dyrness, A.D.; Moore, C.J.; Peterson, W.S.; Scott, M.A.; Shrivastava, H.P.; Sholman, J.S.; Watts, T.N.

    1995-09-01

    The structural acceptance criteria contained herein for the evaluation of existing underground double-shell waste storage tanks located at the Hanford Site is part of the Life Management/Aging Management Program of the Tank Waste Remediation System. The purpose of the overall life management program is to ensure that confinement of the waste is maintained over the required service life of the tanks. Characterization of the present condition of the tanks, understanding and characterization of potential degradation mechanisms, and development of tank structural acceptance criteria based on previous service and projected use are prerequisites to assessing tank integrity, to projecting the length of tank service, and to developing and applying prudent fixes or repairs. The criteria provided herein summarize the requirements for the analysis and structural qualification of the existing double-shell tanks for continued operation. Code reconciliation issues and material degradation under aging conditions are addressed. Although the criteria were developed for double-shell tanks, many of the provisions are equally applicable to single-shell tanks. However, the criteria do not apply to the evaluation of tank appurtenances and buried piping

  11. Selecting the Acceptance Criteria of Medicines in the Reimbursement List of Public Health Insurance of Iran, Using the "Borda" Method: a Pilot Study.

    Science.gov (United States)

    Viyanchi, Amir; Rasekh, Hamid Reza; Rajabzadeh Ghatari, Ali; SafiKhani, Hamid Reza

    2015-01-01

    Decision-making for medicines to be accepted in Iran's public health insurance reimbursement list is a complex process and involves factors, which should be considered in applying a coverage for medicine costs. These processes and factors are not wholly assessed, while assessment of these factors is an essential need for getting a transparent and evidence-based approach toward medicine reimbursement in Iran. This paper aims to show an evidence-based approach toward medicine selection criteria to inform the medical reimbursement decision makers in Iranian health insurance organizations. To explore an adaptable decision-making framework while incorporating a method called "Borda" in medicine reimbursement assessment, we used the help of an expert group including decision makers and clinical researchers who are also policy makers to appraise the five chief criteria that have three sub criteria (Precision, Interpretability, and Cost). Also software "Math-lab"7, "SPSS" 17 and Excel 2007 were used in this study. "Borda" estimates the amount of perceived values from different criteria and creates a range from one to five while providing a comprehensive measurement of a large spectrum of criteria. Participants reported that the framework provided an efficient approach to systematic consideration in a pragmatic format consisting of many parts to guide decision-makings, including criteria and value (a model with the core of Borda) and evidences (medicine reimbursement based on criteria). The most important criterion for medicine acceptance in health insurance companies, in Iran, is the "life-threatening" factor and "evidence quality" is accounted as the fifth important factor. This pilot study showed the usefulness of incorporating Borda in medicine reimbursement decisions to support a transparent and systematic appraisal of health insurance companies' deeds. Further research is needed to advance Borda-based approaches that are effective on health insurance decision making.

  12. Derivation of quantitative acceptance criteria for disposal of radioactive waste to near surface facilities: Development and implementation of an approach for the post-closure phase

    International Nuclear Information System (INIS)

    Torres, C.

    2000-01-01

    The International Atomic Energy Agency has established a project to develop and illustrate, through practical examples, an approach that allows the derivation of quantitative waste acceptance criteria for near surface disposal of radioactive waste. The first phase focussed on the derivation of example post-closure safety waste acceptance criteria through the use of a safety assessment approach that allows for the derivation of values in a clear and well documented manner. The approach consists of five steps: the specification of the assessment context; the description of the disposal system; the development and justification of scenarios; the formulation and implementation of models; and the calculation and derivation of example values. The approach has been successfully used to derive activity values for the disposal of radioactive waste to illustrative near surface facilities. (author)

  13. Evaluation of local hospital discharge for thyroid cancer patients treated with Iodine-131; comparison with internationally accepted release criteria

    International Nuclear Information System (INIS)

    Stylianou-Markidou, E.; Peraticou, A.; Constantinou, C.; Giannos, A.; Aritkan, A.V.; Dimitriadou, D.; Frangos, S.

    2007-01-01

    Full text: Aim: Patients with Thyroid Cancer treated with I-131 in our institution, stay in a shielded room for two days, or until they emit less than 40 μSv/hr at 1m, based on the Cyprus legislation for radiation protection. Other countries have different regulations and public dose limits, and their hospital discharge guidelines vary accordingly. The purpose of this study is to evaluate local hospital discharge regulations, make a comparison with other countries' accepted release criteria, and find where improvements can be made. Methods: 267 patients were treated with I-131 (activity 1.8-8.9GBq) from September 2001 to April 2007. The dose equivalent rate (DER) was measured within 30 min of the administration at a distance of 1 m from the patient. Measurements at 1m were also obtained before the release of the patient. For a group of these patients, measurements were also carried out a week after the treatment with I-131. The doses given to members of the public, from each of the above patients, were calculated using the Total Effective Dose Equivalent (TEDE) concept, which is based on the line source model. For 10% of these patients, measurements of the dose emitted to surroundings were taken, using two different methods. (a) Doses were measured with TLD dosimeters placed at specific points of the room during the two day restriction of the patient in the shielded room. These points were at bedside, at 1 m from the patient's bed, at 3m from the patient's bed, in the shower area, and at the side of the toilet. (b) On the day of release, personal dosimeters were given to a member of the immediate family (carer) of the patient for a minimum of five days. The skin dose and dose at approximately 10cm depth were measured by the National personnel monitoring for radiation protection authority of Cyprus. Results: Our calculation of the TEDE values indicated that, had the patients been released just after the administration of the radiopharmaceutical, members of the

  14. Quality of laboratory studies assessing effects of Bt-proteins on non-target organisms: minimal criteria for acceptability.

    Science.gov (United States)

    De Schrijver, Adinda; Devos, Yann; De Clercq, Patrick; Gathmann, Achim; Romeis, Jörg

    2016-08-01

    The potential risks that genetically modified plants may pose to non-target organisms and the ecosystem services they contribute to are assessed as part of pre-market risk assessments. This paper reviews the early tier studies testing the hypothesis whether exposure to plant-produced Cry34/35Ab1 proteins as a result of cultivation of maize 59122 is harmful to valued non-target organisms, in particular Arthropoda and Annelida. The available studies were assessed for their scientific quality by considering a set of criteria determining their relevance and reliability. As a case-study, this exercise revealed that when not all quality criteria are met, weighing the robustness of the study and its relevance for risk assessment is not obvious. Applying a worst-case expected environmental concentration of bioactive toxins equivalent to that present in the transgenic crop, confirming exposure of the test species to the test substance, and the use of a negative control were identified as minimum criteria to be met to guarantee sufficiently reliable data. This exercise stresses the importance of conducting studies meeting certain quality standards as this minimises the probability of erroneous or inconclusive results and increases confidence in the results and adds certainty to the conclusions drawn.

  15. The effect of discounting, different mortality reduction schemes and predictive cohort life tables on risk acceptability criteria

    International Nuclear Information System (INIS)

    Rackwitz, Ruediger

    2006-01-01

    Technical facilities should be optimal with respect to benefits and cost. Optimization of technical facilities involving risks for human life and limb require an acceptability criterion and suitable discount rates both for the public and the operator depending on for whom the optimization is carried out. The life quality index is presented and embedded into modem socio-economic concepts. A general risk acceptability criterion is derived. The societal life saving cost to be used in optimization as life saving or compensation cost and the societal willingness-to-pay based on the societal value of a statistical life or on the societal life quality index are developed. Different mortality reduction schemes are studied. Also, predictive cohort life tables are derived and applied. Discount rates γ must be long-term averages in view of the time horizon of some 20 to more than 100 years for the facilities of interest and net of inflation and taxes. While the operator may use long-term averages from the financial market for his cost-benefit analysis the assessment of interest rates for investments of the public into risk reduction is more difficult. The classical Ramsey model decomposes the real interest rate (=output growth rate) into the rate of time preference of consumption and the rate of economical growth multiplied by the elasticity of marginal utility of consumption. It is proposed to use a relatively small interest rate of 3% implying a rate of time preference of consumption of about 1%. This appears intergenerationally acceptable from an ethical point of view. Risk-consequence curves are derived for an example

  16. Processing of Irradiated Graphite to Meet Acceptance Criteria for Waste Disposal. Results of a Coordinated Research Project. Companion CD-ROM

    International Nuclear Information System (INIS)

    2016-05-01

    Graphite is widely used in the nuclear industry and in research facilities and this has led to increasing amounts of irradiated graphite residing in temporary storage facilities pending disposal. This publication arises from a coordinated research project (CRP) on the processing of irradiated graphite to meet acceptance criteria for waste disposal. It presents the findings of the CRP, the general conclusions and recommendations. The topics covered include, graphite management issues, characterization of irradiated graphite, processing and treatment, immobilization and disposal. Included on the attached CD-ROM are formal reports from the participants

  17. The Tritiated Water Skin Barrier Integrity Test: Considerations for Acceptance Criteria with and Without 14C-Octanol.

    Science.gov (United States)

    Lehman, Paul A; Beatch, Kacie; Raney, Sam G; Franz, Thomas J

    2017-01-01

    A study was designed to assess barrier integrity simultaneously using separate compounds (probes) for polar and non-polar pathways through the skin, 3 H 2 O and 14 C-octanol, respectively; and to determine whether the two probe approach could better define barrier integrity. A 5-min dose of water containing 3 H 2 O and 14 C -octanol was applied to ex vivo human skin mounted in Franz diffusion cells. The receptor solution was sampled at 30 min, analyzed for 3 H and 14 C content, and the correlation between water and octanol absorption was determined by statistical tests suitable for non-normally distributed data. This study was conducted on skin from 37 donors with from 3 to 30 replicate skin sections per donor (a total of 426 sections). The correlation between 3 H 2 O and 14 C-octanol absorption was low (Pearson correlation coefficient = 0.3485). The 3 H 2 O absorption cutoff used in this study to select for a normal skin barrier rejected some sections in which 14 C-octanol absorption was within normal limits and accepted others in which 14 C-octanol absorption was abnormally high. The converse was true for 3 H 2 O absorption when the 14 C-octanol-based cutoff was used. The results of the 3 H 2 O test or of similar tests that primarily assess the permeability of polar pathways through the skin may not necessarily provide information relevant to the absorption of highly lipophilic compounds. Octanol, or another molecule that more closely matches the physicochemical attributes of the test compound, may characterize properties of the skin barrier that are more relevant to compounds of low water solubility.

  18. Gender Incongruence of Adolescence and Adulthood: Acceptability and Clinical Utility of the World Health Organization's Proposed ICD-11 Criteria.

    Directory of Open Access Journals (Sweden)

    Titia F Beek

    Full Text Available The World Health Organization (WHO is currently updating the tenth version of their diagnostic tool, the International Classification of Diseases (ICD, WHO, 1992. Changes have been proposed for the diagnosis of Transsexualism (ICD-10 with regard to terminology, placement and content. The aim of this study was to gather the opinions of transgender individuals (and their relatives/partners and clinicians in the Netherlands, Flanders (Belgium and the United Kingdom regarding the proposed changes and the clinical applicability and utility of the ICD-11 criteria of 'Gender Incongruence of Adolescence and Adulthood' (GIAA. A total of 628 participants were included in the study: 284 from the Netherlands (45.2%, 8 from Flanders (Belgium (1.3%, and 336 (53.5% from the UK. Most participants were transgender people (or their partners/relatives (n = 522, 89 participants were healthcare providers (HCPs and 17 were both healthcare providers and (partners/relatives of transgender people. Participants completed an online survey developed for this study. Most participants were in favor of the proposed diagnostic term of 'Gender Incongruence' and thought that this was an improvement on the ICD-10 diagnostic term of 'Transsexualism'. Placement in a separate chapter dealing with Sexual- and Gender-related Health or as a Z-code was preferred by many and only a small number of participants stated that this diagnosis should be excluded from the ICD-11. In the UK, most transgender participants thought there should be a diagnosis related to being trans. However, if it were to be removed from the chapter on "psychiatric disorders", many transgender respondents indicated that they would prefer it to be removed from the ICD in its entirety. There were no large differences between the responses of the transgender participants (or their partners and relatives and HCPs. HCPs were generally positive about the GIAA diagnosis; most thought the diagnosis was clearly defined and

  19. Decision modeling and acceptance criteria

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    2003-01-01

    compensation value of a human life and a public money equivalent of a human life, where the last value usually is considerably larger than the first value, it is possible from the decision analysis to determine an upper limit that the public should impose on the ratio of the owner´s expected loss rate......) that combines wealth in terms of Gross Domestic Product per person, life expectancy at birth, and yearly work time into a single number. The philosophy behind the published evaluations is that the prevention of a loss of a life is counteracted by a cost such that the LQI remains unchanged (Skjong R, Ronold K......; Decision Analysis; Life quality index; Random interest rate; Risk aversion; Socio-economic value; Uncertainty aversion...

  20. Risk analysis and risk acceptance criteria in the planning processes of hazardous facilities-A case of an LNG plant in an urban area

    International Nuclear Information System (INIS)

    Vinnem, Jan Erik

    2010-01-01

    Planning of hazardous facilities is usually carried out on the basis of a risk-informed decision-making and planning process making use of risk analysis. This practice is well established in Norway under petroleum legislation but less so for onshore facilities under non-petroleum legislation. The present paper focuses on the use of risk analysis studies for risk evaluation against risk acceptance criteria, risk communication and derivation of technical and operational requirements in these circumstances. This is demonstrated through reference to a case study involving an LNG plant currently under construction in an urban area in Norway. The main finding is that risk-informed legislation is a fragile legislative system which is dependent on conscientious and open-minded use by the industrial developer. In the opposite case, the authorities may well be unable to correct the situation and the legislation may fail to protect the neighbourhood from unreasonable exposure to risk. Reference is also made to the international perspective where authorities define what is deemed tolerable risk, which would appear to be a more robust and defensible approach.

  1. Draft principles, policy, and acceptance criteria for decommissioning of U.S. Department of Energy contaminated surplus facilities and summary of international decommissioning programs

    International Nuclear Information System (INIS)

    Singh, B.K.

    1994-12-01

    Decommissioning activities enable the DOE to reuse all or part of a facility for future activities and reduce hazards to the general public and any future work force. The DOE Office of Environment, Health and Safety has prepared this document, which consists of decommissioning principles and acceptance criteria, in an attempt to establish a policy that is in agreement with the NRC policy. The purpose of this document is to assist individuals involved with decommissioning activities in determining their specific responsibilities as identified in Draft DOE Order 5820.DDD, ''Decommissioning of US Department of Energy Contaminated Surplus Facilities'' (Appendix A). This document is not intended to provide specific decommissioning methodology. The policies and principles of several international decommissioning programs are also summarized. These programs are from the IAEA, the NRC, and several foreign countries expecting to decommission nuclear facilities. They are included here to demonstrate the different policies that are to be followed throughout the world and to allow the reader to become familiar with the state of the art for environment, safety, and health (ES and H) aspects of nuclear decommissioning

  2. Feasibility and acceptability of electronic symptom surveillance with clinician feedback using the Patient-Reported Outcomes version of Common Terminology Criteria for Adverse Events (PRO-CTCAE) in Danish prostate cancer patients

    DEFF Research Database (Denmark)

    Baeksted, Christina; Pappot, Helle; Nissen, Aase

    2017-01-01

    Background: The aim was to examine the feasibility, acceptability and clinical utility of electronic symptom surveillance with clinician feedback using a subset of items drawn from the Patient-Reported Outcomes version of Common Terminology Criteria for Adverse Events (PRO-CTCAE) in a cancer...

  3. Acceptance-criteria for the bedrock for deep geologic disposal of spent nuclear fuel. Proceedings from a seminar at Gothenburg University

    International Nuclear Information System (INIS)

    1995-11-01

    The seminar was directed to Nordic participants, and discussed disposal in the Nordic crystalline bedrock. Criteria for the bedrock should include: It should give durable mechanical protection for the engineered barriers; give a stable and favorable chemical environment for these barriers; have a low turnover of ground water in the near field; be easy to characterize; give favorable recipient-conditions; not have valuable minerals in workable quantities. These general criteria raise several questions coupled to the safety analysis: e.g. the need for geological, hydrological and geochemical parameters. Which data are missing, which are most difficult to find? What should the site characterization program look like to focus on factors that are of the highest importance according to the safety analysis. The demands on the conditions at a site need to be translated into quantitative criteria, which should be expressed as values that can be measured at the site or deduced from such measurements. These questions were discussed at the seminar, and 21 contributions from Finnish, Norwegian and Swedish participants are reported in these proceedings under the chapters: Coupling to the safety analysis; Methodology and criteria for site selection in a regional geoscientific perspective; Rock as a building material - prognosis and result; Geoscientific criteria for the bedrock at the repository - Mechanical protection; Geoscientific criteria for the bedrock at the repository - Low ground water turnover, chemically favorable and stable environment in the near field; Geoscientific criteria for the bedrock at the repository - Demands on the bedrock concerning the migration of radionuclides

  4. Proposed limiting values for performance criteria in acceptance testing of diagnostic X-ray equipment in the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Baeuml, A.

    1989-01-01

    In the Federal Republic of Germany a new X-ray ordinance came into force in 1988 containing a specific paragraph on quality assurance for all medical X-ray units stipulating acceptance tests, regular checks and supervision by medical bodies and the competent authorities. Acceptance testing is to be performed by engineers from equipment suppliers of manufacturers in new and existing installations. It is expected that the service engineers will adjust the equipment in such a way as to obtain optimal performance before measurements are made, the results of which are to be stated in a certificate describing quality status of the equipment. A working group has developed guidelines for these acceptance tests. Items to be measured are reported and proposed limiting values and their tolerances are discussed. (author)

  5. Proposed limiting values for performance criteria in acceptance testing of diagnostic X-ray equipment in the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Baeuml, A.

    1989-01-01

    In the Federal Republic of Germany a new X-ray ordinance came into force in 1988 containing a specific paragraph on quality assurance for all medical X-ray units stipulating acceptance tests, regular checks and supervision by medical bodies and the competent authorities. Acceptance testing is to be performed by engineers from the equipment suppliers or manufacturers in new and also existing installations. It is expected that the service engineers will adjust the equipment in such a way as to obtain optimal performance before measurements are made, the results of which are to be stated in a certificate describing the quality status of the equipment. A working group has developed guidelines for these acceptance tests. The items to be measured are reported and the proposed limiting values and their tolerances are discussed. (author)

  6. Feasibility and acceptability of electronic symptom surveillance with clinician feedback using the Patient-Reported Outcomes version of Common Terminology Criteria for Adverse Events (PRO-CTCAE) in Danish prostate cancer patients

    DEFF Research Database (Denmark)

    Bæksted, Christina; Pappot, Helle; Nissen, Aase

    2017-01-01

    -CTCAE questionnaire on tablet computers using AmbuFlex software at each treatment visit in the outpatient clinic. In total, 22 symptomatic toxicities (41 PRO-CTCAE items), corresponding to the symptomatic adverse-events profile associated with the regimens commonly used for prostate cancer treatment (Docetaxel......Background: The aim was to examine the feasibility, acceptability and clinical utility of electronic symptom surveillance with clinician feedback using a subset of items drawn from the Patient-Reported Outcomes version of Common Terminology Criteria for Adverse Events (PRO-CTCAE) in a cancer...

  7. [Permanent essential defacement--remarks on the possibilities of verification of the accepted criteria in medico-legal certification in criminal and civil law proceedings].

    Science.gov (United States)

    Chowaniec, Czesław; Nowak, Agnieszka; Jabłoński, Christian; Neniczka, Stanisława

    2007-01-01

    Despite the fact that some criteria of medico-legal certification in criminal and civil proceedings have been established, there are still some topics which are controversial and thus require modification. This is also true of the notion of "permanent essential defacement". In the opinion of the authors, changes in social conventions that are occurring nowadays, as well as a highly diversified, subjective perception of esthetic values indicate the need for discussing a possible modification of the presently obligatory criteria. Apart from the assessment of posttraumatic changes, an important problem is posed by defining the notion of "a part of the body customarily open to the view ". Additionally, the authors bring up for discussion the issue of experts taking into consideration the age and sex of the victims while assessing damages. A separate problem lies in difficulties in assessing the degree of detriment to health because of defacement due to the fact that official tables for evaluating permanent or long-term detriment to health do not include relevant information.

  8. Developing Integral Review: IR Editors Reflect on Meta-theory, the Concept of “Integral,” Submission Acceptance Criteria, our Mission, and more.

    Directory of Open Access Journals (Sweden)

    Russ Volckmann

    2007-12-01

    Full Text Available Over the past three years our journey as editors of Integral Review has been full of rich learning. The processes of providing authors with feedback, going over reviews of articles as well as writing ourselves have all contributed to our growth. The primary forum for this learning has been the many conversations amongst us to deal with the various issues that arise in publishing IR. Our intention in this brief piece is to share some of our reflections on this learning journey with you. These will take the form of contributions/reflections from individual editors, allowing us to share with you the particular issues we feel of value in this process. By writing these short pieces, we aim to provide additional resources for understanding how IR works. While we have guidelines and criteria for submissions on our website, it seems that narrative voices from individuals may add some flesh to them. Relating how we perceive issues around writing for an “integral” journal offers a supplement for engaging these criteria, and will hopefully bring them to life. As well, we hope that our writing provides insights into how and what we think about issues relevant to IR’s mission. These pieces reflect the unique voices we have as editors of Integral Review, and demonstrate some of the thinking and passions behind this journal.

  9. Criteria for the development and use of the methodology for environmentally-acceptable fossil energy site evaluation and selection. Volume 2. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Eckstein, L.; Northrop, G.; Scott, R.

    1980-02-01

    This report serves as a companion document to the report, Volume 1: Environmentally-Acceptable Fossil Energy Site Evaluation and Selection: Methodology and Users Guide, in which a methodology was developed which allows the siting of fossil fuel conversion facilities in areas with the least environmental impact. The methodology, known as SELECS (Site Evaluation for Energy Conversion Systems) does not replace a site specific environmental assessment, or an environmental impact statement (EIS), but does enhance the value of an EIS by thinning down the number of options to a manageable level, by doing this in an objective, open and selective manner, and by providing preliminary assessment and procedures which can be utilized during the research and writing of the actual impact statement.

  10. Standard format and content acceptance criteria for the material control and accounting (MC and A) reform amendment: 10 CFR Part 74, Subpart E

    International Nuclear Information System (INIS)

    1987-03-01

    Revisions have been made to the material control and accounting requirements for NRC licensees authorized to possess and use a formula quantity or more of strategic special nuclear material. The revisions require timely monitoring of in-process inventory and discrete items in order to detect anomalies potentially indicative of material losses. Timely detection and enhanced loss localization capabilities will be beneficial to alarm resolution and material recovery in the event of an actual loss. This document presents criteria that can be used by the license applicants and the license reviewers in the preparation and subsequent review of plans to be submitted in response to the the Reform Amendment. General performance objectives, system capabilities, process monitoring, item monitoring, alarm resolution, quality assurance, and accounting are addressed. 43 refs

  11. Gender Incongruence of Adolescence and Adulthood: Acceptability and Clinical Utility of the World Health Organization’s Proposed ICD-11 Criteria

    Science.gov (United States)

    Beek, Titia F.; Cohen-Kettenis, Peggy T.; Bouman, Walter P.; de Vries, Annelou L. C.; Steensma, Thomas D.; Witcomb, Gemma L.; Arcelus, Jon; Richards, Christina; Elaut, Els; Kreukels, Baudewijntje P. C.

    2016-01-01

    The World Health Organization (WHO) is currently updating the tenth version of their diagnostic tool, the International Classification of Diseases (ICD, WHO, 1992). Changes have been proposed for the diagnosis of Transsexualism (ICD-10) with regard to terminology, placement and content. The aim of this study was to gather the opinions of transgender individuals (and their relatives/partners) and clinicians in the Netherlands, Flanders (Belgium) and the United Kingdom regarding the proposed changes and the clinical applicability and utility of the ICD-11 criteria of ‘Gender Incongruence of Adolescence and Adulthood’ (GIAA). A total of 628 participants were included in the study: 284 from the Netherlands (45.2%), 8 from Flanders (Belgium) (1.3%), and 336 (53.5%) from the UK. Most participants were transgender people (or their partners/relatives) (n = 522), 89 participants were healthcare providers (HCPs) and 17 were both healthcare providers and (partners/relatives of) transgender people. Participants completed an online survey developed for this study. Most participants were in favor of the proposed diagnostic term of ‘Gender Incongruence’ and thought that this was an improvement on the ICD-10 diagnostic term of ‘Transsexualism’. Placement in a separate chapter dealing with Sexual- and Gender-related Health or as a Z-code was preferred by many and only a small number of participants stated that this diagnosis should be excluded from the ICD-11. In the UK, most transgender participants thought there should be a diagnosis related to being trans. However, if it were to be removed from the chapter on “psychiatric disorders”, many transgender respondents indicated that they would prefer it to be removed from the ICD in its entirety. There were no large differences between the responses of the transgender participants (or their partners and relatives) and HCPs. HCPs were generally positive about the GIAA diagnosis; most thought the diagnosis was clearly

  12. Present state of the design and realization of regional radioactive waste depositories and waste acceptance criteria for disposal. Soucasny stav reseni a realizace regionalnich ulozist RA odpadu a kriteria prijatelnosti techto odpadu k ukladani

    Energy Technology Data Exchange (ETDEWEB)

    Kortus, J [Chemoprojekt, Prague (Czechoslovakia)

    1988-06-01

    Surface type regional depositories for radioactive wastes from nuclear power plants are described in detail. The depository of the Mochovce nuclear power plant is located near the plant, that of the Dukovany nuclear power plant is directly on the premises of the plant. Particular attention is paid to the design of the monolithic reinforced concrete pits, draining of rainwater from their surface, draining of seeping rainwater from the pit environment by means of a double drainage system, and insulation of the pits against water. The construction of the Mochovce depository started in 1987; some experience gained from this activity is presented. The radioactive waste acceptance criteria for depositories of this kind, based on safety analysis, are given. (author). 2 figs.

  13. Bayesian risk-based acceptance criteria

    International Nuclear Information System (INIS)

    Martz, H.F.; Abramson, L.R.; Johnson, J.W.

    1996-04-01

    Mechanistic (or deterministic) analysis is traditionally performed in the process of designing a new nuclear reactor or reactor core and also as part of the safety analysis of existing reactors or reload cores. Mechanistic accident analysis is characterized by the specification of an initial operating condition, an initiating event, and subsequent system faults. These subsequent faults are often chosen, through such mechanisms as the worst single failure criterion, so as to maximize the consequences of the accident. Thus, the behavior of all reactor system hardware is prescribed before this analysis begins. Mechanistic analysis then attempts to predict the dynamic response of the system and usually involves detailed reactor physics and thermal-hydraulic predictions of the system behavior, including such parameters as power distributions in the reactor core, coolant temperatures and flow rates, and fuel clad temperature distributions. The objective of this analysis has typically been to establish and verify reactor operating limits and technical specifications, so that severe core damage (SCD) is prevented for a wide variety of reactor accidents

  14. Acceptance-criteria for the bedrock for deep geologic disposal of spent nuclear fuel. Proceedings from a seminar at Gothenburg University; Acceptanskriterier foer berggrunden vid djup geologisk slutfoervaring av anvaent kaernbraensle

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The seminar was directed to Nordic participants, and discussed disposal in the Nordic crystalline bedrock. Criteria for the bedrock should include: It should give durable mechanical protection for the engineered barriers; give a stable and favorable chemical environment for these barriers; have a low turnover of ground water in the near field; be easy to characterize; give favorable recipient-conditions; not have valuable minerals in workable quantities. These general criteria raise several questions coupled to the safety analysis: e.g. the need for geological, hydrological and geochemical parameters. Which data are missing, which are most difficult to find? What should the site characterization program look like to focus on factors that are of the highest importance according to the safety analysis. The demands on the conditions at a site need to be translated into quantitative criteria, which should be expressed as values that can be measured at the site or deduced from such measurements. These questions were discussed at the seminar, and 21 contributions from Finnish, Norwegian and Swedish participants are reported in these proceedings under the chapters: Coupling to the safety analysis; Methodology and criteria for site selection in a regional geoscientific perspective; Rock as a building material - prognosis and result; Geoscientific criteria for the bedrock at the repository - Mechanical protection; Geoscientific criteria for the bedrock at the repository - Low ground water turnover, chemically favorable and stable environment in the near field; Geoscientific criteria for the bedrock at the repository - Demands on the bedrock concerning the migration of radionuclides.

  15. Criteria CSR

    OpenAIRE

    Vovk, V.; Zateyshikova, O.

    2014-01-01

    In the article the theoretical aspects regarding criteria for assessing CSR proposed by A. Carroll, including: economic, legal, ethical, philanthropic. Based on this, it is proposed to characterize these criteria with respect to the interested parties (stakeholders), including: investors, shareholders suppliers, customers, employees, society and the state. This will make a qualitative assessment of the presence and depth using social responsibility in the company, as well as determine the ext...

  16. Criteria for decommissioning

    International Nuclear Information System (INIS)

    Ricci, P.F.

    1988-01-01

    In this paper the authors describe three risk acceptability criteria as parts of a strategy to clean up decommissioned facilities, related to both the status quo and to a variety of alternative technical clean-up options. The acceptability of risk is a consideration that must enter into any decision to establish when a site is properly decommissioned. To do so, both the corporate and public aspects of the acceptability issue must be considered. The reasons for discussion the acceptability of risk are to: Legitimize the process for making cleanup decisions; Determine who is at risk, who benefits, and who bears the costs of site cleanup, for each specific cleanup option, including the do nothing option; Establish those factors that, taken as a whole, determine measures of acceptability; Determine chemical-specific aggregate and individual risk levels; and Establish levels for cleanup. The choice of these reasons is pragmatic. The method consistent with these factors is risk-risk-effectiveness: the level of cleanup must be consistent with the foreseeable use of the site and budget constraints. Natural background contamination is the level below which further cleanup is generally inefficient. Case-by-case departures from natural background are to be considered depending on demonstrated risk. For example, a hot spot is obviously a prima facie exception, but should be rebuttable. Rebuttability means that, through consensus, the ''hot spot'' is shown not to be associated with exposure

  17. Acceptability, acceptance and decision making

    International Nuclear Information System (INIS)

    Ackerschott, H.

    2002-01-01

    There is a fundamental difference between the acceptability of a civilizatory or societal risk and the acceptability of the decision-making process that leads to a civilizatory or societal risk. The analysis of individual risk decisions - regarding who, executes when which indisputably hazardous, unhealthy or dangerous behaviour under which circumstances - is not helpful in finding solutions for the political decisions at hand in Germany concerning nuclear energy in particular or energy in general. The debt for implementation of any technology, in the sense of making the technology a success in terms of broad acceptance and general utilisation, lies with the particular industry involved. Regardless of the technology, innovation research identifies the implementation phase as most critical to the success of any innovation. In this sense, nuclear technology is at best still an innovation, because the implementation has not yet been completed. Fear and opposition to innovation are ubiquitous. Even the economy - which is often described as 'rational' - is full of this resistance. Innovation has an impact on the pivotal point between stability, the presupposition for the successful execution of decisions already taken and instability, which includes insecurity, but is also necessary for the success of further development. By definition, innovations are beyond our sphere of experience; not at the level of reliability and trust yet to come. Yet they are evaluated via the simplifying heuristics for making decisions proven not only to be necessary and useful, but also accurate in the familiar. The 'settlement of the debt of implementation', the accompanying communication, the decision-making procedures concerning the regulation of averse effects of the technology, but also the tailoring of the new technology or service itself must be directed to appropriate target groups. But the group often aimed at in the nuclear debate, the group, which largely determines political

  18. Sustainability and acceptance - new challenges for nuclear energy

    International Nuclear Information System (INIS)

    Lensa, W. von

    2001-01-01

    This paper discusses the concept of sustainability in relation to acceptance of nuclear energy. Acceptance is viewed in terms of public acceptance, industrial acceptance, and internal acceptance/consensus within the nuclear community. It addresses sustainability criteria, the need for innovation, and the different levels of acceptability. The mechanisms of risk perception are discussed along with the technological consequences from risk perception mechanisms leading to specific objections against nuclear energy. (author)

  19. Acceptance test procedure for Project W-280

    International Nuclear Information System (INIS)

    Stites, C.G.

    1994-01-01

    This Document is the Acceptance Test Procedure for 200 Area C and SY Tank Farm Lighting Upgrade. This Acceptance Test Procedure has been prepared to demonstrate that the Tank Farm Lighting Systems function correctly as required by project criteria and as intended by design

  20. Safety and reliability criteria

    International Nuclear Information System (INIS)

    O'Neil, R.

    1978-01-01

    Nuclear power plants and, in particular, reactor pressure boundary components have unique reliability requirements, in that usually no significant redundancy is possible, and a single failure can give rise to possible widespread core damage and fission product release. Reliability may be required for availability or safety reasons, but in the case of the pressure boundary and certain other systems safety may dominate. Possible Safety and Reliability (S and R) criteria are proposed which would produce acceptable reactor design. Without some S and R requirement the designer has no way of knowing how far he must go in analysing his system or component, or whether his proposed solution is likely to gain acceptance. The paper shows how reliability targets for given components and systems can be individually considered against the derived S and R criteria at the design and construction stage. Since in the case of nuclear pressure boundary components there is often very little direct experience on which to base reliability studies, relevant non-nuclear experience is examined. (author)

  1. Crew Transportation Technical Standards and Design Evaluation Criteria

    Science.gov (United States)

    Lueders, Kathryn L.; Thomas, Rayelle E. (Compiler)

    2015-01-01

    Crew Transportation Technical Standards and Design Evaluation Criteria contains descriptions of technical, safety, and crew health medical processes and specifications, and the criteria which will be used to evaluate the acceptability of the Commercial Providers' proposed processes and specifications.

  2. Principles for establishing acceptance criteria for releases of chemicals

    International Nuclear Information System (INIS)

    Kirkeskov Jensen, L.

    1989-01-01

    The Danish National Agency of Environmental Protection is in the process of making guidelines for setting limit values on chemicals emission. They are going to serve the following purposes: to promote consistency and improve quality in judicial settlements; to make it possible for the population to evaluate and discuss these settlements; to make it possible for the technical experts to plan their investigations in order to make use of them in a subsequent evaluation; to provide information to the public and enable them to take the necessary precautions against air pollution; and to make it possible to use the guidelines in future planning in e.g. local authorities

  3. Appropriate User Acceptance Criteria For New Social Media Sites

    OpenAIRE

    Mirsat Yeşiltepe

    2016-01-01

    Nowadays social media sites have attracted many of users and they have become the mostly commonly used websites for public. These websites are used by individuals, small and even big organizations for various purposes, such as meeting your old friends, sharing your own experiences, sharing pictures and videos, promoting businesses, sharing knowledge etc. Their popularity is increasing at an increasing rate. User’s needs are endless so there will be some new area for creating...

  4. Criteria for risk acceptance: a health physicist's view

    International Nuclear Information System (INIS)

    Hull, A.P.

    1977-01-01

    A controversy over the safety of nuclear energy has grown in the U.S. since about 1970 and has now spread to near worldwide proportions. This controversy has been fueled by a variety of issues. Initially in the U.S. the most prominent issue concerned the degree of hazard of low-level radiation, in particular that associated with the nuclear fuel cycle. Since then, attention has shifted successively to the reliability of emergency core cooling systems, the longevity of nuclear wastes, the possible misuse of radioactivity by terrorists and the potential for diversion of nuclear-power-produced plutonium to weapons fabrication. Underlying each of these issues has been the implication that the employment of nuclear power will entail an unacceptable risk to the public. A reasonable perspective in this regard is a yearly risk of 1 x 10 -6 compared to the level of natural hazards such as earthquakes, floods, hurricanes, and tornados. Following a satisfactory demonstration of the safety of nuclear energy, hopefully the nuclear argument could be terminated. Society could then move on to the real issues affecting energy, population and quality of life

  5. Design, Test, and Acceptance Criteria for Helicopter Transparent Enclosures

    Science.gov (United States)

    1978-11-01

    measured in the all-glass laminate with rigid edge treatment were approximately 1100 psi when a 500)O-lb load was applied to the post section...clamped 0 .25 CA2 Ball 1289 clamped 0 .25 CA3 Ball 1075 clamped 0 .25 CA4 AP 1432 clamped 0 .25 CAS*** Ball 1155 clamped 0 .50 CA6 Ball 1066 clamped 0...0 0 CA3 1-1/2 0 0 CA4 1 0 0 CA5* -, round diameter 0 0 CA6 1 0 0 PCI smaller than round 0 0 PC2 smaller than round 0 0 PC3 smaller than round 0 0 PC4

  6. Preliminary Acceptance Criteria for Safety Analysis of KALIMER-600 SFR

    International Nuclear Information System (INIS)

    Kwon, Young Min; Lee, Kwi Lim; Ha, Kwi Seok; Chang, Won Pyo; Jeong, Hae Yong

    2010-01-01

    The KALIMER-600 event categorization in the function of occurrence frequency has been made by traditional engineering judgment with information from some reference plants such as CRBR, PRISM and EFR. The dividing line between DBE and BDBE is the frequency of 10 -7 per plant-year. Each event belongs to one of five categories based upon its nominal frequency per reactor-year (f) as a criterion. (1) Moderate frequency Event (MF): f ≥ 10 -1 (2) Infrequent Event (IE): 10 -1 > f ≥ 10 -2 (3) Unlikely Event (UE): 10 -2 > f ≥ 10 -4 (4) Extremely Unlikely Event (XU): 10 -4 > f ≥ 10 -7 (5) Beyond DBE (BDBE): > f ≥ 10 -4

  7. Environmental Restoration Disposal Facility waste acceptance criteria. Revision 1

    International Nuclear Information System (INIS)

    Corriveau, C.E.

    1996-01-01

    The Environmental Restoration Disposal Facility (ERDF) is designed to be an isolation structure for low-level radioactive remediation waste, chemically contaminated remediation waste, and remediation waste that contains both chemical and radioactive constituents (i.e., mixed remediation waste) produced during environmental remediation of Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) past-practice units at the Hanford Site. Remedial action wastes, which will become a structural component of the ERDF, include bulk soil, demolition debris, and miscellaneous wastes from burial grounds. These wastes may originate from CERCLA past-practice sites (i.e., operable units) in the 100 Areas, the 200 Areas, and the 300 Area of the Hanford Site

  8. Probabilistic relationships in acceptable risk studies

    International Nuclear Information System (INIS)

    Benjamin, J.R.

    1977-01-01

    Acceptable risk studies involve uncertainties in future events: consequences and associated values, the acceptability levels, and the future decision environment. Probabilistic procedures afford the basic analytical tool to study the influence of each of these parameters on the acceptable risk decision, including their interrelationships, and combinations. A series of examples are presented in the paper in increasing complexity to illustrate the principles involved and to quantify the relationships to the acceptable risk decision. The basic objective of such studies is to broaden the scientific basis of acceptable risk decision making. It is shown that rationality and consistency in decision making is facilitated by such studies and that rather simple relationships exist in many situations of interest. The variation in criteria associated with an increase in the state of knowledge or change in the level of acceptability is also discussed

  9. Probabilistic relationships in acceptable risk studies

    International Nuclear Information System (INIS)

    Benjamin, J.R.

    1977-01-01

    Acceptable risk studies involve uncertainties in future events; consequences and associated values, the acceptability levels, and the future decision environment. Probabilistic procedures afford the basic analytical tool to study the influence of each of these parameters on the acceptable risk decision, including their interrelationships, and combinations. A series of examples are presented in the paper in increasing complexity to illustrate the principles involved and to quantify the relationships to the acceptable risk decision. The basic objective of such studies is to broaden the scientific basis of acceptable risk decision making. It is shown that rationality and consistency in decision making is facilitated by such studies and that rather simple relationships exist in many situations of interest. The variation in criteria associated with an increase in the state of knowledge or change in the level of acceptability is also discussed. (Auth.)

  10. Risk based seismic design criteria

    International Nuclear Information System (INIS)

    Kennedy, R.P.

    1999-01-01

    In order to develop a risk based seismic design criteria the following four issues must be addressed: (1) What target annual probability of seismic induced unacceptable performance is acceptable? (2) What minimum seismic margin is acceptable? (3) Given the decisions made under Issues 1 and 2, at what annual frequency of exceedance should the safe-shutdown-earthquake (SSE) ground motion be defined? (4) What seismic design criteria should be established to reasonably achieve the seismic margin defined under Issue 2? The first issue is purely a policy decision and is not addressed in this paper. Each of the other three issues are addressed. Issues 2 and 3 are integrally tied together so that a very large number of possible combinations of responses to these two issues can be used to achieve the target goal defined under Issue 1. Section 2 lays out a combined approach to these two issues and presents three potentially attractive combined resolutions of these two issues which reasonably achieves the target goal. The remainder of the paper discusses an approach which can be used to develop seismic design criteria aimed at achieving the desired seismic margin defined in resolution of Issue 2. Suggestions for revising existing seismic design criteria to more consistently achieve the desired seismic margin are presented. (orig.)

  11. Electricity supply between acceptance, acceptability and social compatibility; Energieversorgung zwischen Akzeptanz, Akzeptabilitaet und Sozialvertraeglichkeit

    Energy Technology Data Exchange (ETDEWEB)

    Schubert, Katharina; Koch, Marco K. [Bochum Univ. (Germany). Lehrstuhl Energiesysteme und Energiewirtschaft (LEE)

    2012-11-01

    Acceptance promotion is supposed to be an indispensable premise for a successful realization of an energy concept. The contribution identifies deficiencies of the energy policy, including intransparency, complexity of decision procedures, for instance in case of the so called energy transmission line extension acceleration law, that has caused irritation and anger in the public. The justification of acceptance promotion is questioned in connection with the German nuclear policy reversal following the Fukushima accident. A research program ''public acceptance of large-scale power plants for electricity generation'' is presented. The issues criteria and limits of acceptability are of main importance for this discussion.

  12. Cone penetrometer moisture probe acceptance test report

    International Nuclear Information System (INIS)

    Barnes, G.A.

    1996-01-01

    This Acceptance Test Report (ATR) documents the results of WHC-SD-WM-ATP-146 (Prototype Cone Penetrometer Moisture Probe Acceptance Test Procedure) and WHC-SD-WM-ATP-145 (Cone Penetrometer Moisture Probe Acceptance Test Procedure). The master copy of WHC-SD-WM-ATP-145 can be found in Appendix A and the master copy of WHC-SD-WM-ATP-146 can be found in Appendix B. Also included with this report is a matrix showing design criteria of the cone penetrometer moisture probe and the verification method used (Appendix C)

  13. W-087 Acceptance test procedure. Revision 1

    International Nuclear Information System (INIS)

    Joshi, A.W.

    1997-01-01

    This Acceptance Test Procedure/Operational Test Procedure (ATP/OTP) has been prepared to demonstrate that the Electrical/Instrumentation and Mechanical systems function as required by project criteria and to verify proper operation of the integrated system including the interlocks

  14. W-087 Acceptance test procedure. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, A.W.

    1997-06-10

    This Acceptance Test Procedure/Operational Test Procedure (ATP/OTP) has been prepared to demonstrate that the Electrical/Instrumentation and Mechanical systems function as required by project criteria and to verify proper operation of the integrated system including the interlocks.

  15. Responsible technology acceptance

    DEFF Research Database (Denmark)

    Toft, Madeleine Broman; Schuitema, Geertje; Thøgersen, John

    2014-01-01

    As a response to climate change and the desire to gain independence from imported fossil fuels, there is a pressure to increase the proportion of electricity from renewable sources which is one of the reasons why electricity grids are currently being turned into Smart Grids. In this paper, we focus...... on private consumers’ acceptance of having Smart Grid technology installed in their home. We analyse acceptance in a combined framework of the Technology Acceptance Model and the Norm Activation Model. We propose that individuals are only likely to accept Smart Grid technology if they assess usefulness...... in terms of a positive impact for society and the environment. Therefore, we expect that Smart Grid technology acceptance can be better explained when the well-known technology acceptance parameters included in the Technology Acceptance Model are supplemented by moral norms as suggested by the Norm...

  16. Recommendations for Glass Durability Test Criteria

    International Nuclear Information System (INIS)

    Strachan, D.M.

    1999-01-01

    The objective of this short report is to define a set of activities that should lead to a specification for a test that can be used as one of the acceptance criteria and as an indicator of acceptable long-term behavior in contact with water. Since the glass composition is not yet defined and is likely to change as the composition of the waste changes, a strategy for developing criteria for what is acceptable involves a series of tests and modeling activities. The results of these activities lead to a criterion for an acceptable product and the data that are needed to reliably determine the behavior of the glass in the storage environment

  17. Extended BRS algebra and color confinement criteria

    International Nuclear Information System (INIS)

    Shintani, Meiun.

    1983-09-01

    We examine the color-confinement criteria proposed by Kugo and Ojima. With the use of the extended BRS symmetry and the Nakanishi's theorem, we look for the representations of the BRS algebra compatible with the first condition of their criteria (the K-O condition) and then ask whether or not they are physically acceptable. As a result, the quartet mechanism does not work, and the K-O condition is not regarded as a confinement condition. (author)

  18. Quality criteria for landscape visualisation

    International Nuclear Information System (INIS)

    Waldi, H.-P.; Witt, U. de

    1996-01-01

    The rapid expansion of wind energy utilisation in Western Europe can strain the limits of social acceptance with citizens living in wind development areas. One of the problems wind farm engineers and local authorities face is the visual impact of wind turbines. To determine the influence on the landscape visualisations of wind farms photorealistic compositions are used. In many cases it is part of the planning procedure. The quality of this visualization can strongly influence the success of the permission procedure. We will give criteria which can give help to reduce the possibility of unwanted manipulations. (author)

  19. Safety criteria from the public viewpoint

    International Nuclear Information System (INIS)

    Renn, O.

    1994-01-01

    The paper attempts to outline the scope and limits of a consensus for the evaluation of energy systems, particularly nuclear energy. It is divided into four sections. The first section deals with factual acceptance of technology, while the second inquires into the specific acceptance of nuclear energy, i.e., public perception and valuation of nuclear energy today. The third section discusses criteria of acceptability. In the fourth section, finally, the author deals with questions concerning an energy consensus and presents his own model for approaching this issue. (orig.) [de

  20. Acceptance of spent fuel of varying characteristics

    International Nuclear Information System (INIS)

    Short, S.M.

    1990-03-01

    This paper is a preliminary overview of a study with the primary objective of establishing a set of acceptance selection criteria and corresponding spent fuel characteristics to be incorporated as a component of requirements for the Federal Waste Management System (FWMS). A number of alternative acceptance allocations and selection rules were analyzed to determine the operational sensitivity of each element of the FWMS to the resultant spent fuel characteristics. Preliminary recommendations of the study include three different sets of selection rules to be included in the FWMS design basis. 2 refs., 4 figs., 4 tabs

  1. Acceptance procedures: Microfilm printer

    Science.gov (United States)

    Lockwood, H. E.

    1973-01-01

    Acceptance tests were made for a special order automatic additive color microfilm printer. Tests include film capacity, film transport, resolution, illumination uniformity, exposure range checks, and color cuing considerations.

  2. On risks and acceptability

    International Nuclear Information System (INIS)

    Watson, S.R.

    1981-01-01

    A very attractive notion is that it should be possible not only to determine how much risk is associated with any particular activity, but also to determine if that risk is acceptable. Stated boldly this seems an entirely unobjectionable and indeed a very acceptable notion. There is, however, underlying this idea, a mistaken view of risk which we might refer to as the ''phlogiston'' theory of risk. In this paper, presented at the SRP meeting on Ethical and Legal Aspects of Radiological Protection, the phlogiston theory of risk is described; secondly, it will be argued that it is too simple a theory to be realistic or useful; and thirdly, the management of risk will be placed in a wider decision framework. Acceptability, it will be argued is highly dependent on context, and it is not possible, therefore, to lay down generally applicable notions of acceptability. (author)

  3. Acceptable noise level

    DEFF Research Database (Denmark)

    Olsen, Steen Østergaard; Nielsen, Lars Holme; Lantz, Johannes

    2012-01-01

    The acceptable noise level (ANL) is used to quantify the amount of background noise that subjects can accept while listening to speech, and is suggested for prediction of individual hearing-aid use. The aim of this study was to assess the repeatability of the ANL measured in normal-hearing subjects...... using running Danish and non-semantic speech materials as stimuli and modulated speech-spectrum and multi-talker babble noises as competing stimuli....

  4. Operations Acceptance Management

    OpenAIRE

    Suchá, Ivana

    2010-01-01

    This paper examines the process of Operations Acceptance Management, whose main task is to control Operations Acceptance Tests (OAT). In the first part the author focuses on the theoretical ground for the problem in the context of ITSM best practices framework ITIL. Benefits, process pitfalls and possibilities for automation are discussed in this part. The second part contains a case study of DHL IT Services (Prague), where a solution optimizing the overall workflow was implemented using simp...

  5. Acceptable noise level

    DEFF Research Database (Denmark)

    Olsen, Steen Østergaard; Nielsen, Lars Holme; Lantz, Johannes

    2012-01-01

    The acceptable noise level (ANL) is used to quantify the amount of background noise that subjects can accept while listening to speech, and is suggested for prediction of individual hearing-aid use. The aim of this study was to assess the repeatability of the ANL measured in normal-hearing subjec...... using running Danish and non-semantic speech materials as stimuli and modulated speech-spectrum and multi-talker babble noises as competing stimuli....

  6. Acceptance Probability (P a) Analysis for Process Validation Lifecycle Stages.

    Science.gov (United States)

    Alsmeyer, Daniel; Pazhayattil, Ajay; Chen, Shu; Munaretto, Francesco; Hye, Maksuda; Sanghvi, Pradeep

    2016-04-01

    This paper introduces an innovative statistical approach towards understanding how variation impacts the acceptance criteria of quality attributes. Because of more complex stage-wise acceptance criteria, traditional process capability measures are inadequate for general application in the pharmaceutical industry. The probability of acceptance concept provides a clear measure, derived from specific acceptance criteria for each quality attribute. In line with the 2011 FDA Guidance, this approach systematically evaluates data and scientifically establishes evidence that a process is capable of consistently delivering quality product. The probability of acceptance provides a direct and readily understandable indication of product risk. As with traditional capability indices, the acceptance probability approach assumes that underlying data distributions are normal. The computational solutions for dosage uniformity and dissolution acceptance criteria are readily applicable. For dosage uniformity, the expected AV range may be determined using the s lo and s hi values along with the worst case estimates of the mean. This approach permits a risk-based assessment of future batch performance of the critical quality attributes. The concept is also readily applicable to sterile/non sterile liquid dose products. Quality attributes such as deliverable volume and assay per spray have stage-wise acceptance that can be converted into an acceptance probability. Accepted statistical guidelines indicate processes with C pk > 1.33 as performing well within statistical control and those with C pk  1.33 is associated with a centered process that will statistically produce less than 63 defective units per million. This is equivalent to an acceptance probability of >99.99%.

  7. Biological Water Quality Criteria

    Science.gov (United States)

    Page contains links to Technical Documents pertaining to Biological Water Quality Criteria, including, technical assistance documents for states, tribes and territories, program overviews, and case studies.

  8. A comparison between criteria for diagnosing atopic eczema in infants

    DEFF Research Database (Denmark)

    Jøhnke, H; Vach, W; Norberg, L A

    2005-01-01

    Research Centre (DARC) criteria developed for this study and doctor-diagnosed visible eczema with typical morphology and atopic distribution. Additionally, the U.K. diagnostic criteria based on a questionnaire were used at 1 year of age. Agreement between the four criteria was analysed at each time point...... the four criteria demonstrated that cumulative incidences showed better agreement than point prevalence values. CONCLUSIONS: Agreement between different criteria for diagnosing AE was acceptable, but the mild cases constituted a diagnostic problem, although they were in the minority. Repeated examinations...

  9. 1991 Acceptance priority ranking

    International Nuclear Information System (INIS)

    1991-12-01

    The Standard Contract for Disposal of Spent Nuclear Fuel and/or High- Level Radioactive Waste (10 CFR Part 961) that the Department of Energy (DOE) has executed with the owners and generators of civilian spent nuclear fuel requires annual publication of the Acceptance Priority Ranking (APR). The 1991 APR details the order in which DOE will allocate Federal waste acceptance capacity. As required by the Standard Contract, the ranking is based on the age of permanently discharged spent nuclear fuel (SNF), with the owners of the oldest SNF, on an industry-wide basis, given the highest priority. the 1991 APR will be the basis for the annual allocation of waste acceptance capacity to the Purchasers in the 1991 Annual Capacity Report (ACR), to be issued later this year. This document is based on SNF discharges as of December 31, 1990, and reflects Purchaser comments and corrections, as appropriate, to the draft APR issued on May 15, 1991

  10. FFTBM and primary pressure acceptance criterion

    International Nuclear Information System (INIS)

    Prosek, A.

    2004-01-01

    When thermalhydraulic computer codes are used for simulation in the area of nuclear engineering the question is how to conduct an objective comparison between the code calculation and measured data. To answer this the fast Fourier transform based method (FFTBM) was developed. When the FFTBM method was developed the acceptance criteria for primary pressure and total accuracy were set. In the recent study the FFTBM method was used for accuracy quantification of RD-14M large LOCA test B9401 calculations. The blind accuracy analysis indicated good total accuracy while the primary pressure criterion was not fulfilled. The objective of the study was therefore to investigate the reasons for not fulfilling the primary pressure acceptance criterion and the applicability of the criterion to experimental facilities simulating heavy water reactor. The results of the open quantitative analysis showed that sensitivity analysis for influence parameters provide sufficient information to judge in which calculation the accuracy of primary pressure is acceptable. (author)

  11. Top-level regulatory criteria for the standard MHTGR

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-10-15

    The Licensing Plan for the Standard MHTGR (Ref. 1) describes a program to support a U.S. Nuclear Regulatory Commission (NRC) design review and approval. The Plan calls for the submittal of Top-Level Regulatory Criteria to the NRC for concurrence with their completeness and acceptability for the MHTGR program. The Top-Level Regulatory Criteria are defined as the standards for judging licensability that directly specify acceptable limits for protection of the public health and safety and the environment. The criteria proposed herein are for normal plant operation and a broad spectrum of anticipated events, including accidents. The approach taken is to define a set of criteria which are general as opposed to being design specific. Specifically, it is recommended that criteria be met which: 1. Are less prescriptive than current regulation, thereby encouraging maximum flexibility in design approaches. 2. Are measurable. 3. Are not more strict than the criteria for current power plants.

  12. A STATISTICAL APPROACH FOR DERIVING KEY NFC EVALUATION CRITERIA

    Directory of Open Access Journals (Sweden)

    S.K. KIM

    2014-02-01

    As a result of analyzing the weight of evaluation criteria with the sample of nuclear power experts and the general public, both sides recognized safety as the most important evaluation criterion, and the social factors such as public acceptance appeared to be ranked as more important evaluation criteria by the nuclear energy experts than the general public.

  13. Repository operational criteria analysis

    International Nuclear Information System (INIS)

    Hageman, J.P.; Chowdhury, A.H.

    1992-08-01

    The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations, considering the interfaces and impacts of any potential changes to those regulations. The study addresses regulatory criteria related to the preclosure aspects of the geologic repository. The study task developed regulatory concepts or potential repository operational criteria (PROC) based on analysis of a repository's safety functions and other regulations for similar facilities. These regulatory concepts or PROC were used as a basis to assess the sufficiency and adequacy of the current criteria in 10 CFR Part 60. Where the regulatory concepts were same as current operational criteria, these criteria were referenced. The operations criteria referenced or the PROC developed are given in this report. Detailed analyses used to develop the regulatory concepts and any necessary PROC for those regulations that may require a minor change are also presented. The results of the ROC task showed a need for further analysis and possible major rule change related to the design bases of a geologic repository operations area, siting, and radiological emergency planning

  14. CCS site characterisation criteria

    Energy Technology Data Exchange (ETDEWEB)

    Bachu, S.; Hawkes, C.; Lawton, D.; Pooladi-Darvish, M.; Perkins, E.

    2009-12-15

    IEA GHG recently commissioned the Alberta Research Counil in Canada to conduct a review of storage site selection criteria and site characterisation methods in order to produce a synthesis report. This report reviews the literature on the subject on the site seleciton and characterisation since the publication of the IPCC Special Report on CCS, and provides a synthesis and classification of criteria. 161 refs.

  15. Displacement compressors - acceptance tests

    CERN Document Server

    International Organization for Standardization. Geneva

    1996-01-01

    ISO 1217:2009 specifies methods for acceptance tests regarding volume rate of flow and power requirements of displacement compressors. It also specifies methods for testing liquid-ring type compressors and the operating and testing conditions which apply when a full performance test is specified.

  16. From motivation to acceptability

    DEFF Research Database (Denmark)

    Nordfalk, Francisca; Olejaz, Maria; Jensen, Anja M. B.

    2016-01-01

    Background: Over the past three decades, public attitudes to organ donation have been a subject of numerous studies focusing on donor motivation. Here, we present a fresh approach. We suggest focusing on public acceptability instead of motivation. The point is to understand public attitudes well...

  17. Approaches to acceptable risk

    International Nuclear Information System (INIS)

    Whipple, C.

    1997-01-01

    Several alternative approaches to address the question open-quotes How safe is safe enough?close quotes are reviewed and an attempt is made to apply the reasoning behind these approaches to the issue of acceptability of radiation exposures received in space. The approaches to the issue of the acceptability of technological risk described here are primarily analytical, and are drawn from examples in the management of environmental health risks. These include risk-based approaches, in which specific quantitative risk targets determine the acceptability of an activity, and cost-benefit and decision analysis, which generally focus on the estimation and evaluation of risks, benefits and costs, in a framework that balances these factors against each other. These analytical methods tend by their quantitative nature to emphasize the magnitude of risks, costs and alternatives, and to downplay other factors, especially those that are not easily expressed in quantitative terms, that affect acceptance or rejection of risk. Such other factors include the issues of risk perceptions and how and by whom risk decisions are made

  18. Green Supplier Selection Criteria

    DEFF Research Database (Denmark)

    Nielsen, Izabela Ewa; Banaeian, Narges; Golinska, Paulina

    2014-01-01

    Green supplier selection (GSS) criteria arise from an organization inclination to respond to any existing trends in environmental issues related to business management and processes, so GSS is integrating environmental thinking into conventional supplier selection. This research is designed...... to determine prevalent general and environmental supplier selection criteria and develop a framework which can help decision makers to determine and prioritize suitable green supplier selection criteria (general and environmental). In this research we considered several parameters (evaluation objectives......) to establish suitable criteria for GSS such as their production type, requirements, policy and objectives instead of applying common criteria. At first a comprehensive and deep review on prevalent and green supplier selection literatures performed. Then several evaluation objectives defined to assess the green...

  19. Plutonium storage criteria

    Energy Technology Data Exchange (ETDEWEB)

    Chung, D. [Scientech, Inc., Germantown, MD (United States); Ascanio, X. [Dept. of Energy, Germantown, MD (United States)

    1996-05-01

    The Department of Energy has issued a technical standard for long-term (>50 years) storage and will soon issue a criteria document for interim (<20 years) storage of plutonium materials. The long-term technical standard, {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides,{close_quotes} addresses the requirements for storing metals and oxides with greater than 50 wt % plutonium. It calls for a standardized package that meets both off-site transportation requirements, as well as remote handling requirements from future storage facilities. The interim criteria document, {open_quotes}Criteria for Interim Safe Storage of Plutonium-Bearing Solid Materials{close_quotes}, addresses requirements for storing materials with less than 50 wt% plutonium. The interim criteria document assumes the materials will be stored on existing sites, and existing facilities and equipment will be used for repackaging to improve the margin of safety.

  20. Criteria for safety-related operator actions

    International Nuclear Information System (INIS)

    Gray, L.H.; Haas, P.M.

    1983-01-01

    The Safety-Related Operator Actions (SROA) Program was designed to provide information and data for use by NRC in assessing the performance of nuclear power plant (NPP) control room operators in responding to abnormal/emergency events. The primary effort involved collection and assessment of data from simulator training exercises and from historical records of abnormal/emergency events that have occurred in operating plants (field data). These data can be used to develop criteria for acceptability of the use of manual operator action for safety-related functions. Development of criteria for safety-related operator actions are considered

  1. Nuclear reactor philosophy and criteria

    International Nuclear Information System (INIS)

    Atchison, R.J.

    1979-07-01

    Nuclear power plant safety criteria and principles developed in Canada are directed towards minimizing the chance of failure of the fuel and preventing or reducing to an acceptably low level the escape of fission products should fuel failure occur. Safety criteria and practices are set forth in the Reactor Siting Guide, which is based upon the concept of defence in depth. The Guide specifies that design and construction shall follow the best applicable code, standard or practice; the total of all serious process system failures shall not exceed one in three years; special safety systems are to be physically and functionally separate from process systems and each other; and safety systems shall be testable, with unavailability less than 10 - 3 . Doses to the most exposed member of the public due to normal operation, serious process failures, and dual failures are specified. Licensees are also required to consider the effects of extreme conditions due to airplane crashes, explosions, turbine disintegration, pipe burst, and natural disasters. Safety requirements are changing as nuclear power plant designs evolve and in response to social and economic pressures

  2. Waste acceptance and logistics

    International Nuclear Information System (INIS)

    Carlson, James H.

    1992-01-01

    There are three major components which are normally highlighted when the Civilian Radioactive Waste Management Program is discussed - the repository, the monitored retrievable storage facility, and the transportation system. These are clearly the major physical system elements and they receive the greatest external attention. However, there will not be a successful, operative waste management system without fully operational waste acceptance plans and logistics arrangements. This paper will discuss the importance of developing, on a parallel basis to the normally considered waste management system elements, the waste acceptance and logistics arrangements to enable the timely transfer of spent nuclear fuel from more than one hundred and twenty waste generators to the Federal government. The paper will also describe the specific activities the Program has underway to make the necessary arrangements. (author)

  3. Environment and public acceptance

    International Nuclear Information System (INIS)

    Gauvenet; Bresson; Braillard; Ertaud; Ladonchamps, de; Toureau

    1976-01-01

    The problems involved in the siting of nuclear power stations at a local level are of a political economic, social or ecological order. The acceptance of a nuclear station mostly depends on its interest for the local population. In order to avoid negative reactions, the men who are responsible must make the harmonious integration of the station within the existing economic and social context their first priority [fr

  4. Nuclear power and acceptation

    International Nuclear Information System (INIS)

    Speelman, J.E.

    1990-01-01

    In 1989 a workshop was held organized by the IAEA and the Argonne National Laboratory. The purpose was to investigate under which circumstances a large-scale extension of nuclear power can be accepted. Besides the important technical information, the care for the environment determined the atmosphere during the workshop. The opinion dominated that nuclear power can contribute in tackling the environment problems, but that the social and political climate this almost makes impossible. (author). 7 refs.; 1 fig.; 1 tab

  5. General criteria for radioactive waste disposal

    International Nuclear Information System (INIS)

    Maxey, M.N.; Musgrave, B.C.; Watkins, G.B.

    1979-01-01

    Techniques are being developed for conversion of radioactive wastes to solids and their placement into repositories. Criteria for such disposal are needed to assure protection of the biosphere. The ALARA (as low as reasonably achievable) principle should be applicable at all times during the disposal period. Radioactive wastes can be categorized into three classes, depending on the activity. Three approaches were developed for judging the adequacy of disposal concepts: acceptable risk, ore body comparison, and three-stage ore body comparison

  6. Multimodal freight investment criteria.

    Science.gov (United States)

    2010-07-01

    Literature was reviewed on multi-modal investment criteria for freight projects, examining measures and techniques for quantifying project benefits and costs, as well as ways to describe the economic importance of freight transportation. : A limited ...

  7. Water Quality Criteria

    Science.gov (United States)

    EPA develops water quality criteria based on the latest scientific knowledge to protect human health and aquatic life. This information serves as guidance to states and tribes in adopting water quality standards.

  8. Aquatic Life Criteria - Ammonia

    Science.gov (United States)

    Documents related to EPA's final 2013 Aquatic Life Ambient Water Quality Criteria for Ammonia (Freshwater). These documents pertain to the safe levels of Ammonia in water that should protect to the majority of species.

  9. Aquatic Life Criteria - Copper

    Science.gov (United States)

    Documents pertain to Aquatic Life Ambient Water Quality criteria for Copper (2007 Freshwater, 2016 Estuarine/marine). These documents contain the safe levels of Copper in water that should protect to the majority of species.

  10. Integrated Criteria Document Chromium

    NARCIS (Netherlands)

    Slooff W; Cleven RFMJ; Janus JA; van der Poel P; van Beelen P; Boumans LJM; Canton JH; Eerens HC; Krajnc EI; de Leeuw FAAM; Matthijsen AJCM; van de Meent D; van der Meulen A; Mohn GR; Wijland GC; de Bruijn PJ; van Keulen A; Verburgh JJ; van der Woerd KF

    1990-01-01

    Betreft de engelse versie van rapport 758701001
    Bij dit rapport behoort een appendix onder hetzelfde nummer getiteld: "Integrated Criteria Document Chromium: Effects" Auteurs: Janus JA; Krajnc EI
    (appendix: see 710401002A)

  11. Dual Criteria Decisions

    DEFF Research Database (Denmark)

    Andersen, Steffen; Harrison, Glenn W.; Lau, Morten Igel

    2014-01-01

    The most popular models of decision making use a single criterion to evaluate projects or lotteries. However, decision makers may actually consider multiple criteria when evaluating projects. We consider a dual criteria model from psychology. This model integrates the familiar tradeoffs between...... to the clear role that income thresholds play in such decision making, but does not rule out a role for tradeoffs between risk and utility or probability weighting....

  12. Age and Acceptance of Euthanasia.

    Science.gov (United States)

    Ward, Russell A.

    1980-01-01

    Study explores relationship between age (and sex and race) and acceptance of euthanasia. Women and non-Whites were less accepting because of religiosity. Among older people less acceptance was attributable to their lesser education and greater religiosity. Results suggest that quality of life in old age affects acceptability of euthanasia. (Author)

  13. Rating of environmental criteria

    Energy Technology Data Exchange (ETDEWEB)

    Glueck, K; Krasser, G

    1980-01-01

    After a general theoretical discussion on the question of rating within a framework of cost-benefit studies, first trials as to the quantification and standardisation of twelve selected environmental criteria by means of an indicator system are worked out and compiled. The selection includes the criteria exhaust gas, dust, micro climate, water pollution, water regime, land requirement, vibrations, traffic noise, landscape scene, urban scene, effect of separation and safety risks. An insight is given of the rating practice using an evaluation of the available literature, of a household interview and of an interview of experts. The interviewing of 156 experts as to their rating conception of ten criteria in the second round has provided contributions to the general problem of the evaluation estimate based on multi criteria analysis as well as differentiation of the twelve or ten environmental criteria. The following criteria ratings given by the experts and which are averaged and smoothed are: traffic noise 20,0% +- 8,5; air pollution 15,0% +- 7,0; safety risk 13,0% +- 7,0; soil and water pollution 8,5% +- 5,0; landscape scene 8,0% +- 4,5; urban scene 8,0% +- 4,5; water regime 6,5% +- 3,5 and vibrations 4,5% +- 2,5.

  14. Plugging criteria for WWER SG tubes

    Energy Technology Data Exchange (ETDEWEB)

    Papp, L.; Wilam, M. [Vitkovice NPP Services (Switzerland); Herman, M. [Vuje, Trnava (Slovakia)

    1997-12-31

    At operated Czech and Slovak nuclear power plants the 80 % criteria for crack or other bulk defect depth is used for steam generator heat exchanging tubes plugging. This criteria was accepted as the recommendation of designer of WWER steam generators. Verification of this criteria was the objective of experimental program performed by Vitkovice, J.S.C., UJV Rez, J.S.C. and Vuje Trnava, J.S.C .. Within this program the following factors were studied: (1) Influence of secondary water chemistry on defects initiation and propagation, (2) Statistical evaluation of corrosion defects progression at operated SG, and (3) Determination of critical pressure for tube rupture as a function of eddy current indications. In this presentation items (2) and (3) are considered.

  15. Plugging criteria for WWER SG tubes

    Energy Technology Data Exchange (ETDEWEB)

    Papp, L; Wilam, M [Vitkovice NPP Services (Switzerland); Herman, M [Vuje, Trnava (Slovakia)

    1998-12-31

    At operated Czech and Slovak nuclear power plants the 80 % criteria for crack or other bulk defect depth is used for steam generator heat exchanging tubes plugging. This criteria was accepted as the recommendation of designer of WWER steam generators. Verification of this criteria was the objective of experimental program performed by Vitkovice, J.S.C., UJV Rez, J.S.C. and Vuje Trnava, J.S.C .. Within this program the following factors were studied: (1) Influence of secondary water chemistry on defects initiation and propagation, (2) Statistical evaluation of corrosion defects progression at operated SG, and (3) Determination of critical pressure for tube rupture as a function of eddy current indications. In this presentation items (2) and (3) are considered.

  16. Safety criteria for nuclear chemical plants

    International Nuclear Information System (INIS)

    Ball, P.W.; Curtis, L.M.

    1983-01-01

    Safety measures have always been required to limit the hazards due to accidental release of radioactive substances from nuclear power plants and chemical plants. The risk associated with the discharge of radioactive substances during normal operation has also to be kept acceptably low. BNFL (British Nuclear Fuels Ltd.) are developing risk criteria as targets for safe plant design and operation. The numerical values derived are compared with these criteria to see if plants are 'acceptably safe'. However, the criteria are not mandatory and may be exceeded if this can be justified. The risk assessments are subject to independent review and audit. The Nuclear Installations Inspectorate also has to pass the plants as safe. The assessment principles it uses are stated. The development of risk criteria for a multiplant site (nuclear chemical plants tend to be sited with many others which are related functionally) is discussed. This covers individual members of the general public, societal risks, risks to the workforce and external hazards. (U.K.)

  17. Den betingede accept

    DEFF Research Database (Denmark)

    Kolind, Torsten

    1999-01-01

    The article focus on aspects of identity and social order in relation to the interaction between ‘normals' and ex-prisoners, that is, ex-prisoners, who wants to live a normal life without criminality. It is argued, that this interaction and the normality that the ex-prisoner is granted often......, on the surface, can look rather unproblematic, but that it, none the less, is ruled by, what the author calls the conditioned accept. That is, the ex-prisoner should see himself as normal, at the same time that he withdraw from those situations, practices and attitude where the normals would have difficulties...

  18. Baby-Crying Acceptance

    Science.gov (United States)

    Martins, Tiago; de Magalhães, Sérgio Tenreiro

    The baby's crying is his most important mean of communication. The crying monitoring performed by devices that have been developed doesn't ensure the complete safety of the child. It is necessary to join, to these technological resources, means of communicating the results to the responsible, which would involve the digital processing of information available from crying. The survey carried out, enabled to understand the level of adoption, in the continental territory of Portugal, of a technology that will be able to do such a digital processing. It was used the TAM as the theoretical referential. The statistical analysis showed that there is a good probability of acceptance of such a system.

  19. Acceptance, Tolerance, Participation

    International Nuclear Information System (INIS)

    1993-01-01

    The problem of radioactive waste management from an ethical and societal viewpoint was treated in this seminar, which had participants from universities (social, theological, philosophical and science institutes), waste management industry, and regulatory and controlling authorities. After initial reviews on repository technology, policies and schedules, knowledge gaps, and ethical aspects on decision making under uncertainty, four subjects were treated in lectures and discussions: Democratic collective responsibility, Handling threats in democratic decision making, Waste management - a technological operation with a social dimension, Acceptance and legitimity. Lectures with comments and discussions are collected in this report

  20. Marketing for Acceptance

    Directory of Open Access Journals (Sweden)

    Tina L. Johnston, Ph.D.

    2009-11-01

    Full Text Available Becoming a researcher comes with the credentializing pressure to publish articles in peer-reviewed journals (Glaser, 1992; Glaser, 2007; Glaser, 2008. The work intensive process is exacerbated when the author’s research method is grounded theory. This study investigated the concerns of early and experienced grounded theorists to discover how they worked towards publishing research projects that applied grounded theory as a methodology. The result was a grounded theory of marketing for acceptance that provides the reader with insight into ways that classic grounded theorists have published their works. This is followed by a discussion of ideas for normalizing classic grounded theory research methods in our substantive fields.

  1. Project W-049H Collection System Acceptance Test

    International Nuclear Information System (INIS)

    Buckles, D.I.

    1994-01-01

    The Acceptance Test Procedure (ATP) Program for Project W-049H covers the following activities: Disposal system, Collection system, Instrumentation and control system. Each activity has its own ATP. The purpose of the ATPs is to verify that the systems have been constructed in accordance with the construction documents and to demonstrate that the systems function as required by the Project criteria. This ATP has been prepared to demonstrate that the Collection System Instrumentation functions as required by project criteria

  2. DOE natural phenomenal hazards design and evaluation criteria

    International Nuclear Information System (INIS)

    Murray, R.C.; Nelson, T.A.; Short, S.A.; Kennedy, R.P.; Chander, H.; Hill, J.R.; Kimball, J.K.

    1994-10-01

    It is the policy of the Department of Energy (DOE) to design, construct, and operate DOE facilities so that workers, the general public, and the environment are protected from the impacts of natural phenomena hazards (NPH). Furthermore, DOE has established explicit goals of acceptable risk for NPH performance. As a result, natural phenomena hazard (earthquake, extreme wind, and flood) design and evaluation criteria for DOE facilities have been developed based on target probabilistic performance goals. These criteria include selection of design/evaluation NPH input from probabilistic hazard curves combined with commonly practiced deterministic response evaluation methods and acceptance criteria with controlled levels of conservatism. For earthquake considerations, conservatism is intentionally introduced in specification of material strengths and capacities, in the allowance of limited inelastic behavior, and by a seismic scale factor. Criteria have been developed following a graded approach for several performance goals ranging from that appropriate for normal-use facilities to that appropriate for facilities involving hazardous or critical operations. Performance goals are comprised of qualitative expressions of acceptable behavior and of target quantitative probabilities that acceptable limits of behavior are maintained. The criteria are simple procedures but have a rigorous basis. This paper addresses DOE seismic design and evaluation criteria

  3. Summarized water quality criteria

    International Nuclear Information System (INIS)

    Kempster, P.L.; Hattingh, W.H.J.; Van Vliet, H.R.

    1980-08-01

    The available world literature from 27 sources on existing water quality criteria are summarized for the 15 main uses of water. The minimum, median and maximum specified values for 96 different determinands are included. Under each water use the criteria are grouped according to the functional significance of the determinands e.g. aesthetic/physical effects, high toxic potential, low toxic potential etc. A synopsis is included summarizing salient facts for each determinand such as the conditions under which it is toxic and its relationship to other determinands. The significance of the criteria is briefly discussed and the importance of considering functional interactions between determinands emphasized in evaluating the potential for toxic or beneficial effects. From the source literature it appears that the toxic potential, in addition to being determined by concentration, is also affected by the origin of the substance concerned, i.e. whether from natural sources or from anthropogenic pollution

  4. Radiological design criteria

    International Nuclear Information System (INIS)

    Selby, J.M.; Andersen, B.V.; Carter, L.A.; Waite, D.A.

    1977-01-01

    Many new nuclear facilities are unsatisfactory from a radiation protection point of view, particularly when striving to maintain occupational exposure as low as practicable 'ALAP'. Radiation protection is achieved through physical protective features supplemented by administrative controls. Adequate physical protective feature should be achieved during construction so that supplemental administrative controls may be kept simple and workable. Many nuclear facilities fall short of adequate physical protective features, thus, remedial and sometimes awkward administrative procedures are required to safely conduct work. In reviewing the various handbooks, reports and regulations which deal with radiation protection, it may be noted that there is minimal radiological design guidance for application to nuclear facilities. A set of criteria or codes covering functional areas rather than specific nuclear facility types is badly needed. The following are suggested as functional areas to be considered: characterization of the Facility; siting and access; design exposure limits; layout (people and materials flow); ventilation and effluent control; radiation protection facilities and systems. The application of such radiological design criteria early in the design process would provide some assurance that nuclear facilities will be safe, flexible, and efficient with a minimum of costly retrofitting or administrative restrictions. Criteria which we have found helpful in these functional areas is discussed together with justification for adoption of such criteria and identification of problems which still require solution

  5. Comments on confinement criteria

    International Nuclear Information System (INIS)

    Kurak, V.; Schroer, B.; Swieca, J.A.

    1977-01-01

    For a QED 2 model with SU(n) flavour, the nature of the physical states space is more subtle than one expects on the basis of the loop criterion for confinement. One may have colour confinement without confinement of the fundamental flavour representation. Attempts to formulate confinement criteria in which the quark fields play a more fundamental role are discussed [pt

  6. Acceptance test report for the Westinghouse 100 ton hydraulic trailer

    International Nuclear Information System (INIS)

    Barrett, R.A.

    1995-01-01

    The SY-101 Equipment Removal System 100 Ton Hydraulic Trailer was designed and built by KAMP Systems, Inc. Performance of the Acceptance Test Procedure at KAMP's facility in Ontario, California (termed Phase 1 in this report) was interrupted by discrepancies noted with the main hydraulic cylinder. The main cylinder was removed and sent to REMCO for repair while the trailer was sent to Lampson's facility in Pasco, Washington. The Acceptance Test Procedure was modified and performance resumed at Lampson (termed Phase 2 in this report) after receipt of the repaired cylinder. At the successful conclusion of Phase 2 testing the trailer was accepted as meeting all the performance criteria specified

  7. Public acceptance of nuclear power

    International Nuclear Information System (INIS)

    Wildgruber, O.H.

    1990-01-01

    The lecture addresses the question why we need public acceptance work and provides some clues to it. It explains various human behaviour patterns which determine the basics for public acceptance. To some extent, the opposition to nuclear energy and the role the media play are described. Public acceptance efforts of industry are critically reviewed. Some hints on difficulties with polling are provided. The lecture concludes with recommendations for further public acceptance work. (author)

  8. Multi criteria analysis in the renewable energy industry

    CERN Document Server

    San Cristóbal Mateo, José Ramón

    2012-01-01

    Decision makers in the Renewable Energy sector face an increasingly complex social, economic, technological, and environmental scenario in their decision process. Different groups of decision-makers become involved in the process, each group bringing along different criteria therefore, policy formulation for fossil fuel substitution by Renewable Energies must be addressed in a multi-criteria context. Multi Criteria Analysis in the Renewable Energy Industry is a direct response to the increasing interest in the Renewable Energy industry which can be seen as an important remedy to many environmental problems that the world faces today. The multiplicity of criteria and the increasingly complex social, economic, technological, and environmental scenario makes multi-criteria analysis a valuable tool in the decision-making process for fossil fuel substitution. The detailed chapters explore the use of the Multi-criteria decision-making methods and how they provide valuable assistance in reaching equitable and accept...

  9. Sediment quality criteria: A review with recommendations for developing criteria for the Hanford Site

    Energy Technology Data Exchange (ETDEWEB)

    Driver, C.J.

    1994-05-01

    Criteria for determining the quality of liver sediment are necessary to ensure that concentrations of contaminants in aquatic systems are within acceptable limits for the protection of aquatic and human life. Such criteria should facilitate decision-making about remediation, handling, and disposal of contaminants. Several approaches to the development of sediment quality criteria (SQC) have been described and include both descriptive and numerical methods. However, no single method measures all impacts at all times to all organisms (U.S. EPA 1992b). The U.S. EPA`s interest is primarily in establishing chemically based, numerical SQC that are applicable nation-wide (Shea 1988). Of the approaches proposed for SQC development, only three are being considered for numerical SQC on a national level. These approaches include an Equilibrium Partitioning Approach, a site-specific method using bioassays (the Apparent Effects Threshold Approach), and an approach similar to EPA`s water quality criteria (Pavlou and Weston 1984). Although national (or even regional) criteria address a number of political, litigative, and engineering needs, some researchers feel that protection of benthic communities require site-specific, biologically based criteria (Baudo et al. 1990). This is particularly true for areas where complex mixtures of contaminants are present in sediments. Other scientifically valid and accepted procedures for freshwater SQC include a background concentration approach, methods using field or spiked bioassays, a screening level concentration approach, the Apparent Effects Threshold Approach, the Sediment Quality Triad, the International Joint Commission Sediment Assessment Strategy, and the National Status and Trends Program Approach. The various sediment assessment approaches are evaluated for application to the Hanford Reach and recommendations for Hanford Site sediment quality criteria are discussed.

  10. HPS simulation and acceptance

    Energy Technology Data Exchange (ETDEWEB)

    Mundim, Luiz Martins [UERJ, Rio de Janeiro, RJ (Brazil); Pol, Maria Elena [CBPF, Rio de Janeiro, RJ (Brazil)

    2013-07-01

    Full text: The High Precision Spectrometer (HPS) is a proposal of sub-detector to be installed in the region of 200-240m from each side of CMS along the LHC beam-line to measure scattered protons from exclusive centrally produced processes, pp → p + X + p. In order to study the protons that reach the detectors, the beam-line of the LHC accelerator has to be taken into account, as the particles are deflected by dipoles and suffer the influence of quadrupoles and other beam devices. The LHC team provides a detailed description of these elements, currents, energies, magnetic fields, and all the information needed to study the propagation of the protons. The program HECTOR, developed at the University of Louvain, uses the information from LHC to calculate at any point along the beam-line the kinematic quantities that characterize the scattered protons. A simple minded program was initially developed for the preliminary studies of acceptances varying the position and size of the foreseen detectors. Also, it took into account vertex and position smearing, to simulate a realistic resolution of the tracking detectors. These studies were performed using a particle gun generator which shoot protons from the IP within reasonable ranges of possible t and ξ (the square of the four-momentum transfer and the fractional energy loss of the outgoing proton in a diffractive collision), and propagated them to the position of the tracking detectors. These kinematic quantities were reconstructed back at the IP using the transport equations from HECTOR. This simplified simulation was afterwards interfaced with the full software of CMS, CMSSW, in such a way that when a diffractive event was fully simulated and reconstructed in the central detector, the outgoing protons were treated by the HPS software and then the complete (CMS+HPS) event was output. The ExHuME generator was used to produce Monte Carlo simulations to study the mass acceptance of the HPS detector, and central and

  11. Proposed radiological protection criteria for waste disposal options

    International Nuclear Information System (INIS)

    Hill, M.D.

    1981-01-01

    Criteria which are based solely on the consequences of releases of radionuclides, that is doses to man, are inappropriate for decisions on the acceptability of many of the disposal options for solid wastes. The risks associated with disposal options in which the intention is to isolate wastes from the biosphere for any length of time have two major components: the probability that a release of radionuclides will occur and the probability that subsequent radiation doses will give rise to deleterious effects. It is therefore necessary to develop criteria which embody the basic radiological principle of keeping risks to acceptable levels and take account of both components of risk. In this paper proposed criteria are described and some of the implications of adopting these criteria are discussed. (author)

  12. Bridging the Gap between Social Acceptance and Ethical Acceptability.

    Science.gov (United States)

    Taebi, Behnam

    2017-10-01

    New technology brings great benefits, but it can also create new and significant risks. When evaluating those risks in policymaking, there is a tendency to focus on social acceptance. By solely focusing on social acceptance, we could, however, overlook important ethical aspects of technological risk, particularly when we evaluate technologies with transnational and intergenerational risks. I argue that good governance of risky technology requires analyzing both social acceptance and ethical acceptability. Conceptually, these two notions are mostly complementary. Social acceptance studies are not capable of sufficiently capturing all the morally relevant features of risky technologies; ethical analyses do not typically include stakeholders' opinions, and they therefore lack the relevant empirical input for a thorough ethical evaluation. Only when carried out in conjunction are these two types of analysis relevant to national and international governance of risky technology. I discuss the Rawlsian wide reflective equilibrium as a method for marrying social acceptance and ethical acceptability. Although the rationale of my argument is broadly applicable, I will examine the case of multinational nuclear waste repositories in particular. This example will show how ethical issues may be overlooked if we focus only on social acceptance, and will provide a test case for demonstrating how the wide reflective equilibrium can help to bridge the proverbial acceptance-acceptability gap. © 2016 The Authors Risk Analysis published by Wiley Periodicals, Inc. on behalf of Society for Risk Analysis.

  13. Acceptance test report, plutonium finishing plant life safety upgrade

    International Nuclear Information System (INIS)

    Hodge, S.G.

    1994-01-01

    This acceptance Test Procedure (ATP) has been prepared to demonstrate that modifications to the Fir Protection systems function as required by project criteria. The ATP will test the Fire Alarm Control Panels, Flow Alarm Pressure Switch, Heat Detectors, Smoke Detectors, Flow Switches, Manual Pull Stations, and Gong/Door By Pass Switches

  14. Human Systems Design Criteria

    DEFF Research Database (Denmark)

    Rasmussen, Jens

    1982-01-01

    This paper deals with the problem of designing more humanised computer systems. This problem can be formally described as the need for defining human design criteria, which — if used in the design process - will secure that the systems designed get the relevant qualities. That is not only...... the necessary functional qualities but also the needed human qualities. The author's main argument is, that the design process should be a dialectical synthesis of the two points of view: Man as a System Component, and System as Man's Environment. Based on a man's presentation of the state of the art a set...... of design criteria is suggested and their relevance discussed. The point is to focus on the operator rather than on the computer. The crucial question is not to program the computer to work on its own conditions, but to “program” the operator to function on human conditions....

  15. Bioethics and conflicting ethical criteria.

    Science.gov (United States)

    George, Michael

    2002-01-01

    Some of the major problematic issues in contemporary ethical discourse are highlighted in the field of bioethics. The need to incorporate new understandings and foundational shifts in essential criteria because of technological advances in the areas of medicine and human sciences increasingly challenges traditional and accepted notions of ethics. As the possibilities of technical progress increase, more and more pressure is put on traditional understandings of the human person, identity, and value. In the face of ethical relativism and emotivism, which are already widespread in social and political discourse, the immediacy of bioethics as a response to technology and its impact on human lives reinforces the need for ethics to become interdisciplinary, while attempting to provide some coherence to both the questions and the responses that contemporary life generates. In this paper, the author intends to sketch the outlines of some of these problems, and suggest one approach which might allow a certain methodical intelligibility to emerge which takes into account shifts in consciousness and the dependence on historically grounded perspective.

  16. Intelligent intefrace design criteria

    International Nuclear Information System (INIS)

    Sicard, Y.; Siebert, S.; Thebault, M.H.

    1990-01-01

    Optimum adequation between control means and the capacities of the teams of operators is sought for to achieve computerization of control and monitoring interfaces. Observation of the diagnosis activity of populations of operators in incident situations on a simulator enables design criteria well-suited to the characteristics of the detection, interpretation of symptoms and incident location tasks to be defined. A software tool based on a qualitative approach enables the design process to be systematized

  17. The leak before break criteria, requirements and implications

    International Nuclear Information System (INIS)

    Martinez M, E.

    1992-05-01

    Inside this work a general balance is made on the Leak before break approach (LBB), like they are the history and licensing, those limitations, the acceptance criteria of the LBB, the current state of the regulatory development and the current state of it application in countries like E.U.A, Germany, Canada, Italy and France. Everything it with the purpose of evaluating the opportunities that offers the LBB criteria for it possible application in Mexico. (Author)

  18. NWTS program criteria for mined geologic disposal of nuclear waste: program objectives, functional requirements, and system performance criteria

    International Nuclear Information System (INIS)

    1981-04-01

    At the present time, final repository criteria have not been issued by the responsible agencies. This document describes general objectives, requirements, and criteria that the DOE intends to apply in the interim to the National Waste Terminal Storage (NWTS) Program. These objectives, requirements, and criteria have been developed on the basis of DOE's analysis of what is needed to achieve the National objective of safe waste disposal in an environmentally acceptable and economic manner and are expected to be consistent with anticipated regulatory standards. The qualitative statements in this document address the broad issues of public and occupational health and safety, institutional acceptability, engineering feasibility, and economic considerations. A comprehensive set of criteria, general and project specific, of which these are a part, will constitute a portion of the technical basis for preparation and submittal by the DOE of formal documents to support future license applications for nuclear waste repositories

  19. NWTS program criteria for mined geologic disposal of nuclear waste: program objectives, functional requirements, and system performance criteria

    Energy Technology Data Exchange (ETDEWEB)

    None

    1981-04-01

    At the present time, final repository criteria have not been issued by the responsible agencies. This document describes general objectives, requirements, and criteria that the DOE intends to apply in the interim to the National Waste Terminal Storage (NWTS) Program. These objectives, requirements, and criteria have been developed on the basis of DOE's analysis of what is needed to achieve the National objective of safe waste disposal in an environmentally acceptable and economic manner and are expected to be consistent with anticipated regulatory standards. The qualitative statements in this document address the broad issues of public and occupational health and safety, institutional acceptability, engineering feasibility, and economic considerations. A comprehensive set of criteria, general and project specific, of which these are a part, will constitute a portion of the technical basis for preparation and submittal by the DOE of formal documents to support future license applications for nuclear waste repositories.

  20. Protocol for the verification of minimum criteria

    International Nuclear Information System (INIS)

    Gaggiano, M.; Spiccia, P.; Gaetano Arnetta, P.

    2014-01-01

    This Protocol has been prepared with reference to the provisions of article 8 of the Legislative Decree of May 26, 2000 No. 187. Quality controls of radiological equipment fit within the larger 'quality assurance Program' and are intended to ensure the correct operation of the same and the maintenance of that State. The pursuit of this objective guarantees that the radiological equipment subjected to those controls also meets the minimum criteria of acceptability set out in annex V of the aforementioned legislative decree establishing the conditions necessary to allow the functions to which each radiological equipment was designed, built and for which it is used. The Protocol is established for the purpose of quality control of radiological equipment of Cone Beam Computer Tomography type and reference document, in the sense that compliance with stated tolerances also ensures the subsistence minimum acceptability requirements, where applicable.

  1. The Success Criteria of Scientific Pedagogic Activities

    Directory of Open Access Journals (Sweden)

    M. V. Ovchinnikov

    2013-01-01

    Full Text Available The paper considers the problem of scientific pedagogic activity assessment of the higher school academic staff. The existing options of quality estimation are listed along with their deficiencies; the most acceptable in the authors’ opinion being the systematic approach. The latter allows considering almost every aspect of scientific-pedagogic activity. On that ground, the authors recommend the following success estimation criteria: gnostic, projecting, communicative, informational, and organizational. The criteria of work satisfaction and its results are taken into consideration as additional ones. The indicators of each criterion are given demonstrating that the as- sessment can be both internal (subjective and external (objective, denoted in the normative acts. The problem of complex and just quality assessment of scientific- pedagogic activity is quite relevant as it affects the academic staff motivation. The authors believe that the research findings can improve the objectivity of teachers’ work assessment and give way to differentiated approaches to their motivation and stimulation. 

  2. Technical considerations associated with spent fuel acceptance. Final report

    International Nuclear Information System (INIS)

    Supko, E.M.

    1996-06-01

    This study was initiated by the Electric Power Research Institute (EPRI) to identify technical considerations associated with spent fuel acceptance and implementation of a waste management system that includes the use of transportable storage systems, and to serve as an opening dialogue among Standard Contract Holders and the department of Energy's Office of Civilian Radioactive Waste management (OCRWM) prior to the development of waste acceptance criteria or issuance of a Notice of Proposed Rulemaking by OCRWM to amend the Standard Contract. The original purpose of the Notice of Proposed Rulemaking was to address changes to the Standard Contract to implement a multi-purpose canister based system and to address other issues that were not adequately addressed in the standard contract. Even if DOE does not develop a multi-purpose canister based system for waste acceptance, it will still be necessary to develop waste acceptance criteria in order to accept spent fuel in transportable storage systems that are being deployed for at-reactor storage. In this study, technical issues associated with spent fuel acceptance will be defined and potential options and alternatives for resolution of technical considerations will be explored

  3. Radioactive facilities classification criteria

    International Nuclear Information System (INIS)

    Briso C, H.A.; Riesle W, J.

    1992-01-01

    Appropriate classification of radioactive facilities into groups of comparable risk constitutes one of the problems faced by most Regulatory Bodies. Regarding the radiological risk, the main facts to be considered are the radioactive inventory and the processes to which these radionuclides are subjected. Normally, operations are ruled by strict safety procedures. Thus, the total activity of the radionuclides existing in a given facility is the varying feature that defines its risk. In order to rely on a quantitative criterion and, considering that the Annual Limits of Intake are widely accepted references, an index based on these limits, to support decisions related to radioactive facilities, is proposed. (author)

  4. Criteria for software modularization

    Science.gov (United States)

    Card, David N.; Page, Gerald T.; Mcgarry, Frank E.

    1985-01-01

    A central issue in programming practice involves determining the appropriate size and information content of a software module. This study attempted to determine the effectiveness of two widely used criteria for software modularization, strength and size, in reducing fault rate and development cost. Data from 453 FORTRAN modules developed by professional programmers were analyzed. The results indicated that module strength is a good criterion with respect to fault rate, whereas arbitrary module size limitations inhibit programmer productivity. This analysis is a first step toward defining empirically based standards for software modularization.

  5. American acceptance of nuclear power

    International Nuclear Information System (INIS)

    Barrett, W.

    1980-01-01

    The characteristic adventurous spirit that built American technology will eventually lead to American acceptance of nuclear power unless an overpowering loss of nerve causes us to reject both nuclear technology and world leadership. The acceptance of new technology by society has always been accompanied by activist opposition to industralization. To resolve the debate between environmental and exploitive extremists, we must accept with humility the basic premise that human accomplishment is a finite part of nature

  6. Tacit acceptance of the succession

    Directory of Open Access Journals (Sweden)

    Ioana NICOLAE

    2012-01-01

    Full Text Available This paper examines some essential and contradictory aspects regarding the issue of tacit acceptance of succession in terms of distinction between documents valuing tacit acceptance of succession and other acts that would not justify such a solution. The documents expressly indicated by the legislator as having tacit acceptance value as well as those which do not have such value are presented and their most important legal effects are examined and discussed.

  7. The development of criteria for radioactive waste disposal

    International Nuclear Information System (INIS)

    Wagstaff, K.P.

    1985-02-01

    Radiation protection criteria are needed in Canada for judging the acceptability of radioactive waste disposal options for which there are potential long-term radiological impacts. This paper discusses the difficulties encountered in applying the ICRP system of dose limitation to the long term and the alternative approaches to criteria being developed and adopted by various other international and national bodies. Finally, the present situation in Canada is reviewed and conclusions are drawn on the general direction in which national criteria are being formulated and expressed

  8. Bridging the Gap between Social Acceptance and Ethical Acceptability

    NARCIS (Netherlands)

    Taebi, B.

    2016-01-01

    New technology brings great benefits, but it can also create new and significant risks. When evaluating those risks in policymaking, there is a tendency to focus on social acceptance. By solely focusing on social acceptance, we could, however, overlook important ethical aspects of technological

  9. The use of fracture mechanics for the evaluation of NDE flaw acceptance standards

    Energy Technology Data Exchange (ETDEWEB)

    Alicino, A; Capurro, E; Ansaldo, Sp; Corvi, A [Ansaldo SpA, Genoa (Italy)

    1988-12-31

    This document deals with the use of fracture mechanics criteria to evaluate the Non Destructive Examination (NDE) flaw acceptance standards. The communication discusses the general schemes and the guidelines of the activity carried out. (TEC).

  10. Acceptance test procedure for High Pressure Water Jet System

    International Nuclear Information System (INIS)

    Crystal, J.B.

    1995-01-01

    The overall objective of the acceptance test is to demonstrate a combined system. This includes associated tools and equipment necessary to perform cleaning in the 105 K East Basin (KE) for achieving optimum reduction in the level of contamination/dose rate on canisters prior to removal from the KE Basin and subsequent packaging for disposal. Acceptance tests shall include necessary hardware to achieve acceptance of the cleaning phase of canisters. This acceptance test procedure will define the acceptance testing criteria of the high pressure water jet cleaning fixture. The focus of this procedure will be to provide guidelines and instructions to control, evaluate and document the acceptance testing for cleaning effectiveness and method(s) of removing the contaminated surface layer from the canister presently identified in KE Basin. Additionally, the desired result of the acceptance test will be to deliver to K Basins a thoroughly tested and proven system for underwater decontamination and dose reduction. This report discusses the acceptance test procedure for the High Pressure Water Jet

  11. Combining the IADPSG criteria with the WHO diagnostic criteria for ...

    African Journals Online (AJOL)

    Macrosomia or at least one adverse outcome were more likely in GDM patients who met the diagnostic criteria by both the IADPSG and WHO criteria (P = 0.001). Conclusion: A diagnosis of GDM that meets both the WHO and IADPSG criteria provides stronger prediction for adverse pregnancy outcome than a diagnosis that ...

  12. A Statistical Approach for Deriving Key NFC Evaluation Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Kim, S. K; Kang, G. B.; Ko, W. I [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Young, S. R.; Gao, R. X. [Univ. of Science and Technology, Daejeon (Korea, Republic of)

    2014-02-15

    This study suggests 5 evaluation criteria (safety and technology, environmental impact, economic feasibility, social factors, and institutional factors) and 24 evaluation indicators for a NFC (nuclear fuel cycle) derived using factor analysis. To do so, a survey using 1 on 1 interview was given to nuclear energy experts and local residents who live near nuclear power plants. In addition, by conducting a factor analysis, homogeneous evaluation indicators were grouped with the same evaluation criteria, and unnecessary evaluation criteria and evaluation indicators were dropped out. As a result of analyzing the weight of evaluation criteria with the sample of nuclear power experts and the general public, both sides recognized safety as the most important evaluation criterion, and the social factors such as public acceptance appeared to be ranked as more important evaluation criteria by the nuclear energy experts than the general public.

  13. A Statistical Approach for Deriving Key NFC Evaluation Criteria

    International Nuclear Information System (INIS)

    Kim, S. K; Kang, G. B.; Ko, W. I; Young, S. R.; Gao, R. X.

    2014-01-01

    This study suggests 5 evaluation criteria (safety and technology, environmental impact, economic feasibility, social factors, and institutional factors) and 24 evaluation indicators for a NFC (nuclear fuel cycle) derived using factor analysis. To do so, a survey using 1 on 1 interview was given to nuclear energy experts and local residents who live near nuclear power plants. In addition, by conducting a factor analysis, homogeneous evaluation indicators were grouped with the same evaluation criteria, and unnecessary evaluation criteria and evaluation indicators were dropped out. As a result of analyzing the weight of evaluation criteria with the sample of nuclear power experts and the general public, both sides recognized safety as the most important evaluation criterion, and the social factors such as public acceptance appeared to be ranked as more important evaluation criteria by the nuclear energy experts than the general public

  14. Key acceptability attributes of orodispersible films.

    Science.gov (United States)

    Scarpa, Mariagiovanna; Paudel, Amrit; Kloprogge, Frank; Hsiao, Wen Kai; Bresciani, Massimo; Gaisford, Simon; Orlu, Mine

    2018-04-01

    The features rendering orodispersible films (ODFs) patient-centric formulations are widely discussed in the scientific literature. However there is a lack of research studies exploring ODF characteristics with a potential impact on end-user acceptability. The aim of this study was to identify the key ODF characteristics affecting end-user acceptability by developing in vitro test methods for the prediction of ODFs acceptability and correlate these formulation characteristics with the data obtained from a human panel study. Four drug-free single-polymer films were prepared by solvent casting. Solutions of poly(vinyl) alcohol (PVOH) 39 KDa (P1), PVOH 197 KDa (P2), carboxymethylcellulose (CMC) 395 KDa (C1), and CMC 725 KDa (C2) were prepared. Texture analysis and Dynamic Mechanical Analysis (DMA) were used to assess film tack. Petri dish and drop methods were used to assess disintegration time. A human panel of 24 healthy young adults was employed to identify end-user acceptability criteria of the four study film samples. Texture analysis data of ODF tack were not found to be in agreement with the in vivo perceived stickiness in the mouth. However, measurement of the area under the adhesive force curve obtained by DMA correlated with in vivo perceived stickiness data for all samples. The disintegration times obtained by drop method were more comparable to human panel data than the petri dish method. Hence DMA and drop methods proved to be promising methodologies for the prediction of the end-user acceptability. The type and molecular weight of the film-forming polymer had a strong influence on stickiness perception, whereas only polymeric molecular weight influenced perceived disintegration time. The human panel study showed that Participant Reported Outcomes (PROs) for the perceived stickiness in the mouth and disintegration time of test films received significantly different scores between samples, and thus were identified as the key attributes with the

  15. Laser Safety Inspection Criteria

    International Nuclear Information System (INIS)

    Barat, K

    2005-01-01

    A responsibility of the Laser Safety Officer (LSO) is to perform laser safety audits. The American National Standard Z136.1 Safe use of Lasers references this requirement in several sections: (1) Section 1.3.2 LSO Specific Responsibilities states under Hazard Evaluation, ''The LSO shall be responsible for hazards evaluation of laser work areas''; (2) Section 1.3.2.8, Safety Features Audits, ''The LSO shall ensure that the safety features of the laser installation facilities and laser equipment are audited periodically to assure proper operation''; and (3) Appendix D, under Survey and Inspections, it states, ''the LSO will survey by inspection, as considered necessary, all areas where laser equipment is used''. Therefore, for facilities using Class 3B and or Class 4 lasers, audits for laser safety compliance are expected to be conducted. The composition, frequency and rigueur of that inspection/audit rests in the hands of the LSO. A common practice for institutions is to develop laser audit checklists or survey forms. In many institutions, a sole Laser Safety Officer (LSO) or a number of Deputy LSO's perform these audits. For that matter, there are institutions that request users to perform a self-assessment audit. Many items on the common audit list and the associated findings are subjective because they are based on the experience and interest of the LSO or auditor in particular items on the checklist. Beam block usage is an example; to one set of eyes a particular arrangement might be completely adequate, while to another the installation may be inadequate. In order to provide more consistency, the National Ignition Facility Directorate at Lawrence Livermore National Laboratory (NIF-LLNL) has established criteria for a number of items found on the typical laser safety audit form. These criteria are distributed to laser users, and they serve two broad purposes: first, it gives the user an expectation of what will be reviewed by an auditor, and second, it is an

  16. National Recommended Water Quality Criteria

    Data.gov (United States)

    U.S. Environmental Protection Agency — The National Recommended Water Quality Criteria is a compilation of national recommended water quality criteria for the protection of aquatic life and human health...

  17. Cone penetrometer acceptance test report

    Energy Technology Data Exchange (ETDEWEB)

    Boechler, G.N.

    1996-09-19

    This Acceptance Test Report (ATR) documents the results of acceptance test procedure WHC-SD-WM-ATR-151. Included in this report is a summary of the tests, the results and issues, the signature and sign- off ATP pages, and a summarized table of the specification vs. ATP section that satisfied the specification.

  18. Acceptance conditions in automated negotiation

    NARCIS (Netherlands)

    Baarslag, T.; Hindriks, K.V.; Jonker, C.M.

    2011-01-01

    In every negotiation with a deadline, one of the negotiating parties has to accept an offer to avoid a break off. A break off is usually an undesirable outcome for both parties, therefore it is important that a negotiator employs a proficient mechanism to decide under which conditions to accept.

  19. Consumer Acceptance of Novel Foods

    NARCIS (Netherlands)

    Fischer, A.R.H.; Reinders, M.J.

    2016-01-01

    The success of novel foods depends to a considerable extent on whether consumers accept those innovations. This chapter provides an overview of current knowledge relevant to consumer acceptance of innovations in food. A broad range of theories and approaches to assess consumer response to

  20. Worldwide nuclear revival and acceptance

    International Nuclear Information System (INIS)

    Geraets, Luc H.; Crommelynck, Yves A.

    2009-01-01

    The current status and trends of the nuclear revival in Europe and abroad are outlined. The development of public opinion in the last decade is playing an important part. This has turned from clear rejection to careful acceptance. Transparency and open communication will be important aspects in the further development of nuclear acceptance. (orig.)

  1. Current quality criteria

    International Nuclear Information System (INIS)

    Sajaroff, Pedro M.

    1999-01-01

    The Safety Series 50-C/SG-Q 'Quality Assurance for Safety in Nuclear Power Plants and other Nuclear Installations' published by the IAEA in 1996, contains the Code and 14 Safety Guides. It is more addressed to operating organizations than to regulatory authorities. Priority is assigned to programme implementation and to work effectiveness. Emphasis is putted on doing work correctly from the very beginning (right first time attitude), and not on finding and correcting errors instead of preventing them. The essential aspects for assuring quality (that is, for achieving and maintaining an acceptable level of safety) cover the ten basic requirements established by the Code: Management (QA programme, training and qualification, non-conformance control and corrective actions, document control and records); Performance (work, design, procurement, inspection and testing for acceptance); and Assessment (management self-assessment, independent assessment). These requirements are applicable, on a graded approach basis, to the overall QA programme of the operating organization and its partial programmes during design, construction, commissioning, operation and decommissioning stages. The requirements can be also applied, with due adaptations, to other nuclear installations. The research and development activities related to such stages are comprised under the quality 'umbrella' as well. Therefore the scope of the traditional quality assurance is expanded and consolidated as a management tool more oriented to user. Responsibilities for achieving quality objectives are assigned to all involved individuals and organizations at all levels: management, working groups and assessment teams. Managers' is important but individual responsibilities are unavoidable. For the Argentine Nuclear Regulatory Authority, performance-based quality assurance was not a novelty. In line with the regulatory philosophy (which is essentially based on performance) the regulatory standard AR 3.6.1 (Rev.1

  2. Laser Safety Inspection Criteria

    International Nuclear Information System (INIS)

    Barat, K.

    2005-01-01

    A responsibility of the Laser Safety Officer (LSO) is to perform laser audits. The American National Standard Z136.1 Safe Use of Lasers references this requirement through several sections. One such reference is Section 1.3.2.8, Safety Features Audits, ''The LSO shall ensure that the safety features of the laser installation facilities and laser equipment are audited periodically to assure proper operation''. The composition, frequency and rigor of that inspection/audit rests in the hands of the LSO. A common practice for institutions is to develop laser audit checklists or survey forms It is common for audit findings from one inspector or inspection to the next to vary even when reviewing the same material. How often has one heard a comment, ''well this area has been inspected several times over the years and no one ever said this or that was a problem before''. A great number of audit items, and therefore findings, are subjective because they are based on the experience and interest of the auditor to particular items on the checklist. Beam block usage, to one set of eyes might be completely adequate, while to another, inadequate. In order to provide consistency, the Laser Safety Office of the National Ignition Facility Directorate has established criteria for a number of items found on the typical laser safety audit form. The criteria are distributed to laser users. It serves two broad purposes; first, it gives the user an expectation of what will be reviewed by an auditor. Second, it is an opportunity to explain audit items to the laser user and thus the reasons for some of these items, such as labelling of beam blocks

  3. Diagnostic Criteria for Pediatric MS

    Directory of Open Access Journals (Sweden)

    J Gordon Millichap

    2013-06-01

    Full Text Available Investigators at Northwestern University Feinberg School of Medicine and Ann & Robert H. Lurie Children’s Hospital of Chicago review the diagnostic criteria for pediatric multiple sclerosis, the differential diagnosis, the 2010 McDonald criteria, and Callen criteria.

  4. Development of small reactor safety criteria in Canada

    International Nuclear Information System (INIS)

    Ernst, P.C.; French, P.M.; Axford, D.J.; Snell, V.G.

    1990-01-01

    A number of new small reactor designs have been proposed in Canada over the last several years and some have reached the stage where licensing discussions have been initiated with the Atomic Energy Control Board (AECB). An inter-organizational Small Reactor Criteria (SRC) working group was formed in 1988 to propose safety and licensing criteria for these small reactors. Two levels of criteria are proposed. The first level forms a safety philosophy and the second is a set of criteria for specific reactor applications. The safety philosophy consists of three basic safety objectives together with evaluation criteria, and fourteen fundamental principles measured by specific criteria, which must be implemented to meet the safety objectives. Two of the fourteen principles are prime: defence in depth, and safety culture; the other twelve principles can be seen as deriving from them. A benefit of this approach is that the concepts of defence in depth and safety culture become well-defined. The objectives and principles are presented in the paper and their criteria are summarized. The second level of criteria, under development, will form a safety application set and will provide small reactor criteria in a number of general areas, such as regulatory process and safety assessment, as well as for specific reactor life-cycle activities, from siting through to decommissioning. The criteria are largely deterministic. However, the frequencies and consequences of postulated accidents are assessed against numerical criteria to assist in judging the acceptability of plant design, operation, and proposed siting. All criteria proposed are designed to be testable in some evidentiary fashion, readily enabling an assessment of compliance for a given proposal

  5. Decision criteria in PSA applications

    International Nuclear Information System (INIS)

    Holmberg, J.E.; Pulkkinen, U.; Rosqvist, T.; Simola, K.

    2001-11-01

    Along with the adoption of risk informed decision making principles, the need for formal probabilistic decision rule or criteria has been risen. However, there are many practical and theoretical problems in the application of probabilistic criteria. One has to think what is the proper way to apply probabilistic rules together with deterministic ones and how the criteria are weighted with respect to each other. In this report, we approach the above questions from the decision theoretic point of view. We give a short review of the most well known probabilistic criteria, and discuss examples of their use. We present a decision analytic framework for evaluating the criteria, and we analyse how the different criteria behave under incompleteness or uncertainty of the PSA model. As the conclusion of our analysis we give recommendations on the application of the criteria in different decision situations. (au)

  6. Consumer acceptance of functional foods

    DEFF Research Database (Denmark)

    Frewer, Lynn J.; Scholderer, Joachim; Lambert, Nigel

    2003-01-01

    In the past, it has been assumed that consumers would accept novel foods if there is a concrete and tangible consumer benefit associated with them, which implies that those functional foods would quickly be accepted. However, there is evidence that individuals are likely to differ in the extent...... to which they are likely to buy products with particular functional properties. Various cross-cultural and demographic differences in acceptance found in the literature are reviewed, as well as barriers to dietary change. In conclusion, it is argued that understanding consumer's risk perceptions...

  7. Analysis of existing work-zone devices with MASH safety performance criteria.

    Science.gov (United States)

    2009-02-01

    Crashworthy, work-zone, portable sign support systems accepted under NCHRP Report No. 350 were analyzed to : predict their safety peformance according to the TL-3 MASH evaluation criteria. An analysis was conducted to determine : which hardware param...

  8. Most Scottish neurologists do not apply the 2010 McDonald criteria when diagnosing multiple sclerosis.

    Science.gov (United States)

    Lumley, R; Davenport, R; Williams, A

    2015-03-01

    The diagnostic criteria for multiple sclerosis have evolved over time and currently the 2010 McDonald criteria are the most widely accepted. These criteria allow the diagnosis of multiple sclerosis to be made at the clinically isolated syndrome stage provided certain criteria are met on a single magnetic resonance brain scan. Our hypothesis was that neurologists in Scotland did not use these criteria routinely. We sent a SurveyMonkey questionnaire to all Scottish neurologists (consultants and trainees) regarding the diagnosis of multiple sclerosis. Our questionnaire response rate was 65/99 (66%). Most Scottish neurologists were aware of the criteria and 31/58 (53%) felt that they were using these routinely. However, in a clinical vignette designed to test the application of these criteria, only 5/57 (9%) of neurologists appeared to use them. Scottish neurologists' use of the 2010 McDonald criteria for diagnosis of multiple sclerosis varies from practitioners' perception of their use of these criteria.

  9. Preliminary waste acceptance requirements for the planned Konrad repository

    International Nuclear Information System (INIS)

    Warnecke, E.; Brennecke, P.

    1987-01-01

    The Physikalisch-Technische Bundesanstalt (PTB) has established Preliminary Waste Acceptance Requirements for the planned Konrad repository. These requirements were developed, in accordance with the Safety Criteria of the Reactor Safety Commission, with the help of a site specific safety assessment; they are under the reservation of the plan approval procedure, which is still in progress. In developing waste acceptance requirements, the PTB fulfills one of its duties as the institute responsible for waste disposal and gives guidelines for waste conditioning to waste producers and conditioners. (orig.) [de

  10. ACR appropriateness criteria jaundice.

    Science.gov (United States)

    Lalani, Tasneem; Couto, Corey A; Rosen, Max P; Baker, Mark E; Blake, Michael A; Cash, Brooks D; Fidler, Jeff L; Greene, Frederick L; Hindman, Nicole M; Katz, Douglas S; Kaur, Harmeet; Miller, Frank H; Qayyum, Aliya; Small, William C; Sudakoff, Gary S; Yaghmai, Vahid; Yarmish, Gail M; Yee, Judy

    2013-06-01

    A fundamental consideration in the workup of a jaundiced patient is the pretest probability of mechanical obstruction. Ultrasound is the first-line modality to exclude biliary tract obstruction. When mechanical obstruction is present, additional imaging with CT or MRI can clarify etiology, define level of obstruction, stage disease, and guide intervention. When mechanical obstruction is absent, additional imaging can evaluate liver parenchyma for fat and iron deposition and help direct biopsy in cases where underlying parenchymal disease or mass is found. Imaging techniques are reviewed for the following clinical scenarios: (1) the patient with painful jaundice, (2) the patient with painless jaundice, and (3) the patient with a nonmechanical cause for jaundice. The ACR Appropriateness Criteria are evidence-based guidelines for specific clinical conditions that are reviewed every 2 years by a multidisciplinary expert panel. The guideline development and review include an extensive analysis of current medical literature from peer-reviewed journals and the application of a well-established consensus methodology (modified Delphi) to rate the appropriateness of imaging and treatment procedures by the panel. In those instances where evidence is lacking or not definitive, expert opinion may be used to recommend imaging or treatment. Copyright © 2013 American College of Radiology. Published by Elsevier Inc. All rights reserved.

  11. Criteria of site assessment

    International Nuclear Information System (INIS)

    Gibbs, P.; Fuchs, H.

    1975-01-01

    The criteria which lead to the choice of a particular site for a nuclear power station are in general very similar to those which would apply to any other type of power station. The principal differences derive from the simpler transport problems for the fuel compared with, say, solid fuel and the special safety considerations which attach to nuclear reactors. The search for a suitable site obviously starts by considering where the power is needed, i.e. where the load centers are and also the existing transmission network which may help to bring the power from a more remote site to the load centers. This economic incentive to put the plant close to loads conflicts directly with the nuclear safety argument which favours more remote siting, and part of the problem of site selection is to reconcile these two matters. In addition, there are many other important matters which will be considered later concerning the adequacy of cooling water supplies, foundation conditions, etc., all of which must be examined in considerable detail. (orig./TK) [de

  12. Criteria for performance evaluation

    Directory of Open Access Journals (Sweden)

    David J. Weiss

    2009-03-01

    Full Text Available Using a cognitive task (mental calculation and a perceptual-motor task (stylized golf putting, we examined differential proficiency using the CWS index and several other quantitative measures of performance. The CWS index (Weiss and Shanteau, 2003 is a coherence criterion that looks only at internal properties of the data without incorporating an external standard. In Experiment 1, college students (n = 20 carried out 2- and 3-digit addition and multiplication problems under time pressure. In Experiment 2, experienced golfers (n = 12, also college students, putted toward a target from nine different locations. Within each experiment, we analyzed the same responses using different methods. For the arithmetic tasks, accuracy information (mean absolute deviation from the correct answer, MAD using a coherence criterion was available; for golf, accuracy information using a correspondence criterion (mean deviation from the target, also MAD was available. We ranked the performances of the participants according to each measure, then compared the orders using Spearman's rextsubscript{s}. For mental calculation, the CWS order correlated moderately (rextsubscript{s} =.46 with that of MAD. However, a different coherence criterion, degree of model fit, did not correlate with either CWS or accuracy. For putting, the ranking generated by CWS correlated .68 with that generated by MAD. Consensual answers were also available for both experiments, and the rankings they generated correlated highly with those of MAD. The coherence vs. correspondence distinction did not map well onto criteria for performance evaluation.

  13. FHR Generic Design Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, George F [ORNL; Holcomb, David Eugene [ORNL; Cetiner, Sacit M [ORNL

    2012-06-01

    The purpose of this document is to provide an initial, focused reference to the safety characteristics of and a licensing approach for Fluoride-Salt-Cooled High-Temperature Reactors (FHRs). The document does not contain details of particular reactor designs nor does it attempt to identify or classify either design basis or beyond design basis accidents. Further, this document is an initial attempt by a small set of subject matter experts to document the safety and licensing characteristics of FHRs for a larger audience. The document is intended to help in setting the safety and licensing research, development, and demonstration path forward. Input from a wider audience, further technical developments, and additional study will be required to develop a consensus position on the safety and licensing characteristics of FHRs. This document begins with a brief overview of the attributes of FHRs and then a general description of their anticipated safety performance. Following this, an overview of the US nuclear power plant approval process is provided that includes both test and power reactors, as well as the role of safety standards in the approval process. The document next describes a General Design Criteria (GDC) - based approach to licensing an FHR and provides an initial draft set of FHR GDCs. The document concludes with a description of a path forward toward developing an FHR safety standard that can support both a test and power reactor licensing process.

  14. Geomembrane selection criteria for uranium tailings ponds

    International Nuclear Information System (INIS)

    Mitchell, D.H.; Cuello, R.

    1986-09-01

    The selection criteria, particularly those involving chemical compatibility, of geomembranes to be used in ponds at uranium mill operations are discussed. The principal functional criteria which a geomembrane must meet for this application are: (1) a specified service life and (2) low permeability. Chemical compatibility with the waste is essential in meeting these functional criteria. In two different types of aging tests using simulated acidic uranium mill waste, degradation of chemical and physical properties were examined in geomembranes of high-density polyethylene, polyvinyl chloride, and chlorosulfonated polyethylene. Compatibility tests according to the National Sanitation Foundation procedures are recommended to ascertain the stability of certain physical properties of the proposed geomembrane. Actual experience with a specific geomembrane in an identical application is probably the best method to assure compatibility; however, this experience is frequently not available. Experience with a geomembrane in similar applications is valuable in the selection process, however, small differences in either the geomembrane formulation or the waste composition may result in large differences in performance of the geomembrane. It is likely that many geomembranes have acceptable chemical stability for typical uranium mill applications, therefore, additional factors in the selection processes will include seaming characteristics, mechanical properties, site characteristics, and costs

  15. Criteria for candidate species for aquaculture

    Energy Technology Data Exchange (ETDEWEB)

    Webber, H H; Riordan, P F

    1976-01-01

    The nature of the animal taxa that are the most probable candidates for an intensive, commercial aquatic animal husbandry industry is considered. A characterization is presented of those biological criteria that lend the species the necessary physiological and genetic malleability to be adapted and molded into a domesticated race. The animal cultivated must be amenable to intensive management in high-density confinements such as those now being engineered for high-yield aquaculture. Attributes considered are discussed in the context of the various aquacultural ecosystems in which the specific biotype is expected to achieve satisfactory growth and survival. Correlative with bionomic criteria, economic requirements are posed and evaluated in an effort to define a socially and financially profitable agribusiness system. Investment requirements and operating costs are considered in terms of expected returns. However, since production alone is insufficient to sustain an enterprise - i.e., the product must be sold - production costs must be judged against market values. Therefore, ultimate use or consumer acceptance criteria are incorporated into the list of essential requirements for a candidate species for aquafarming.

  16. Ecological radiation protection criteria for nuclear power

    International Nuclear Information System (INIS)

    Kryshev, I.I.

    1993-01-01

    By now a large quantity of radioactive hazards of all sizes and shapes has accumulated in Russia. They include RBMK, VVER, and BN (fast-neutron) nuclear power plants, nuclear fuel processing plants, radioactive waste dumps, ships with nuclear power units, etc. In order to evaluate the radioecological situation correctly, the characteristics of the radioactive contamination must be compiled in these areas with some system of criteria which will provide an acceptable level of ecological safety. Currently health criteria for radiation protection are, which are oriented to man's radiation protection, predominate. Here the concept of a thresholdless linear dose-response dependence, which has been confirmed experimentally only at rather high doses (above 1 Gy), is taken as the theoretical basis for evaluating and normalizing radiation effects. According to one opinion, protecting people against radiation is sufficient to protect other types of organisms, although they are not necessarily of the same species. However, from the viewpoint of ecology, this approach is incorrect, because it does not consider radiation dose differences between man and other living organisms. The article discusses dose-response dependences for various organisms, biological effects of ionizing radiation, and appropriate radiation protection criteria

  17. Market Acceptance of Smart Growth

    Science.gov (United States)

    This report finds that smart growth developments enjoy market acceptance because of stability in prices over time. Housing resales in smart growth developments often have greater appreciation than their conventional suburban counterparts.

  18. L-286, Acceptance Test Record

    International Nuclear Information System (INIS)

    HARMON, B.C.

    2000-01-01

    This document provides a detailed account of how the acceptance testing was conducted for Project L-286, ''200E Area Sanitary Water Plant Effluent Stream Reduction''. The testing of the L-286 instrumentation system was conducted under the direct supervision

  19. Standards regulations and public acceptance

    International Nuclear Information System (INIS)

    Fernandez, E.C.

    1977-01-01

    Spanish nuclear legislation and the associated procedure for the authorization of installations is summarized. Public acceptance is discussed in the context of the needs for and hazards of nuclear energy. (U.K.)

  20. Idaho National Engineering Laboratory release criteria for decontamination and decommissioning

    International Nuclear Information System (INIS)

    Dolenc, M.R.; Case, M.J.

    1986-01-01

    Criteria have been developed for release of Idaho National Engineering Laboratory (INEL) facilities and land areas following decontamination and decommissioning (D and D). Decommissioning release criteria in the form of dose guidelines were proposed by the US Nuclear Regulatory Commission as early as 1980. These criteria were used on an interim basis for INEL D and D projects. However, dose guidelines alone do not adequately cover the criteria necessary to release sites for unrestricted use. In actual practice, other parameters such as pathways analyses, sampling and instrumentation techniques, and implementation procedures are required to develop the basis for unrestricted release of a site. Thus, a rigorous approach for evaluating these other parameters is needed to develop acceptable D and D release criteria. Because of the complex and sensitive nature of the dose and pathways analyses work, a thorough review by experts in those respective fields was desired. Input and support in preparing or reviewing each part of the criteria development task was solicited from several DOE field offices. Experts were identified and contracted to assist in preparing portions of the release criteria, or to serve on a peer-review committee. Thus, the entire release criteria development task was thoroughly reviewed by recognized experts from each DOE field office, to validate technical content of the INEL site-specific document

  1. Public acceptance of small reactors

    International Nuclear Information System (INIS)

    McDougall, D.S.

    1997-01-01

    The success of any nuclear program requires acceptance by the local public and all levels of government involved in the decision to initiate a reactor program. Public acceptance of a nuclear energy source is a major challenge in successful initiation of a small reactor program. In AECL's experience, public acceptance will not be obtained until the public is convinced that the specific nuclear program is needed, safe and economic and environmental benefit to the community. The title of public acceptance is misleading. The objective of the program is a fully informed public. The program proponent cannot force public acceptance, which is beyond his control. He can, however, ensure that the public is informed. Once information has begun to flow to the public by various means as will be explained later, the proponent is responsible to ensure that the information that is provided by him and by others is accurate. Most importantly, and perhaps most difficult to accomplish, the proponent must develop a consultative process that allows the proponent and the public to agree on actions that are acceptable to the proponent and the community

  2. Water quality criteria for lead

    Energy Technology Data Exchange (ETDEWEB)

    Nagpal, N.K.

    1987-01-01

    This report is one in a series that establishes water quality criteria for British Columbia. The report sets criteria for lead to protect a number of water uses, including drinking water, freshwater and marine aquatic life, wildlife, livestock, irrigation, and recreation. The criteria are set as either maximum concentrations of total lead that should not be exceeded at any time, or average concentrations that should not be exceeded over a 30-day period. Actual values are summarized.

  3. Criteria for Authorship in Bioethics

    OpenAIRE

    Resnik, David B.; Master, Zubin

    2011-01-01

    Multiple authorship is becoming increasingly common in bioethics research. There are well-established criteria for authorship in empirical bioethics research but not for conceptual research. It is important to develop criteria for authorship in conceptual publications to prevent undeserved authorship and uphold standards of fairness and accountability. This article explores the issue of multiple authorship in bioethics and develops criteria for determining who should be an author on a concept...

  4. Scientific opinion on the evaluation of substances as acceptable previous cargoes for edible fats and oils

    DEFF Research Database (Denmark)

    Petersen, Annette

    Shipping of edible fats and oils into Europe is permitted in bulk tanks, provided that the previous cargo is included in a positive list. The European Commission requested EFSA to evaluate the acceptability as previous cargoes for fats and oils the substances calcium lignosulphonate, methyl acetate...... the criteria for acceptability as previous cargoes. Due to uncertainties, mainly with regard to the composition and toxicity of the low molecular mass fraction, and the fact that the toxicological database is limited to the 40–65 grade and does not cover all grades of calcium lignosulphonate shipped...... as previous cargoes, the EFSA Panel on Contaminants in the Food Chain (CONTAM Panel) concluded that calcium lignosulphonate does not meet the criteria for acceptability as a previous cargo. Only food-grade ammonium sulphate meets the criteria for acceptability as a previous cargo due to uncertainties about...

  5. UO3 deactivation end point criteria

    International Nuclear Information System (INIS)

    Stefanski, L.D.

    1994-01-01

    The UO 3 Deactivation End Point Criteria are necessary to facilitate the transfer of the UO 3 Facility from the Office of Facility Transition and Management (EM-60) to the office of Environmental Restoration (EM-40). The criteria were derived from a logical process for determining end points for the systems and spaces at the UO 3 , Facility based on the objectives, tasks, and expected future uses pertinent to that system or space. Furthermore, the established criteria meets the intent and supports the draft guidance for acceptance criteria prepared by EM-40, open-quotes U.S. Department of Energy office of Environmental Restoration (EM-40) Decontamination and Decommissioning Guidance Document (Draft).close quotes For the UO 3 Facility, the overall objective of deactivation is to achieve a safe, stable and environmentally sound condition, suitable for an extended period, as quickly and economically as possible. Once deactivated, the facility is kept in its stable condition by means of a methodical surveillance and maintenance (S ampersand M) program, pending ultimate decontamination and decommissioning (D ampersand D). Deactivation work involves a range of tasks, such as removal of hazardous material, elimination or shielding of radiation fields, partial decontamination to permit access for inspection, installation of monitors and alarms, etc. it is important that the end point of each of these tasks be established clearly and in advance, for the following reasons: (1) End points must be such that the central element of the deactivation objective - to achieve stability - is unquestionably achieved. (2) Much of the deactivation work involves worker exposure to radiation or dangerous materials. This can be minimized by avoiding unnecessary work. (3) Each task is, in effect, competing for resources with other deactivation tasks and other facilities. By assuring that each task is appropriately bounded, DOE's overall resources can be used most fully and effectively

  6. Early Site Permit Demonstration Program: Regulatory criteria evaluation report

    International Nuclear Information System (INIS)

    1993-03-01

    The primary objective of the Early Site Plan Demonstration Program (ESPDP) is to demonstrate successfully the use of 10CFR52 to obtain ESPs for one or more US sites for one (or more) ALWR nuclear power plants. It is anticipated that preparation of the ESP application and interaction with NRC during the application review process will result not only in an ESP for the applicant(s) but also in the development of criteria and definition of processes, setting the precedent that facilitates ESPs for subsequent ESP applications. Because siting regulatory processes and acceptance criteria are contained in over 100 separate documents, comprehensive licensing and technical reviews were performed to establish whether the requirements and documentation are self-consistent, whether the acceptance criteria are sufficiently well-defined and clear, and whether the licensing process leading to the issuance of an ESP is unambiguously specified. This document provides appendices A and B of this report. Appendix A contains a list of regulations, regulatory guidance, and acceptance criteria; Appendix B contains a cross-reference index of siting-related documentation

  7. Combining the IADPSG criteria with the WHO diagnostic criteria for ...

    African Journals Online (AJOL)

    The International Association of Diabetes in Pregnancy Study Group (IADPSG) and World Health ... Macrosomia or at least one adverse outcome were more likely in GDM patients who ... criteria for GDM in the ADA's more recent position statement.[18] .... at risk for postpartum type 2 DM;[27] the IADPSG criteria on the other ...

  8. Spent nuclear fuel project-criteria document Cold Vacuum Drying Facility phase 2 safety analysis report

    International Nuclear Information System (INIS)

    Garvin, L.J.

    1998-01-01

    The criteria document provides the criteria and guidance for developing the SNF CVDF Phase 2 SAR. This SAR will support the US Department of Energy, Richland Operations Office decision to authorize the procurement, installation, and installation acceptance testing of the CVDF systems

  9. Some problems in the acceptability of implementing radiation protection programs

    International Nuclear Information System (INIS)

    Neill, R.H.

    1997-01-01

    The three fundamentals that radiation protection programs are based upon are; 1) establishing a quantitative correlation between radiation exposure and biological effects in people; 2) determining a level of acceptable risk of exposure; and 3) establishing systems to measure the radiation dose to insure compliance with the regulations or criteria. The paper discusses the interrelationship of these fundamentals, difficulties in obtaining a consensus of acceptable risk and gives some examples of problems in identifying the most critical population-at-risk and in measuring dose. Despite such problems, it is recommended that we proceed with the existing conservative structure of radiation protection programs based upon a linear no threshold model for low radiation doses to insure public acceptability of various potential radiation risks. Voluntary compliance as well as regulatory requirements should continue to be pursued to maintain minimal exposure to ionizing radiation. (author)

  10. Acceptance test report for the Westinghouse 100 ton hydraulic trailer

    Energy Technology Data Exchange (ETDEWEB)

    Barrett, R.A.

    1995-03-06

    The SY-101 Equipment Removal System 100 Ton Hydraulic Trailer was designed and built by KAMP Systems, Inc. Performance of the Acceptance Test Procedure at KAMP`s facility in Ontario, California (termed Phase 1 in this report) was interrupted by discrepancies noted with the main hydraulic cylinder. The main cylinder was removed and sent to REMCO for repair while the trailer was sent to Lampson`s facility in Pasco, Washington. The Acceptance Test Procedure was modified and performance resumed at Lampson (termed Phase 2 in this report) after receipt of the repaired cylinder. At the successful conclusion of Phase 2 testing the trailer was accepted as meeting all the performance criteria specified.

  11. [Organization of socially acceptable working hours in nursing].

    Science.gov (United States)

    Büssing, A; Glaser, J

    1994-05-01

    Three dimensions in the structure of the working hour system of nurses, rendering them socially acceptable, are becoming important: duration of the working day, the time of day which is being worked and the distribution of working hours. The latter two are of particular importance because flexible shift is becoming the dominant pattern in nursing. Six indicators are discussed as criteria for social acceptability: security of employment which includes access to the labour-market, level of income, health, opportunity for social relationships, social participation, and autonomy. Responses of 297 nurses in one General Hospital taking part in a study, were analysed to examine empirically the concept of 'socially acceptable structure of the working hours'. Ideal and factual patterns are considered first. Secondly aspects of autonomy are considered and the way this depends on time, thirdly the criteria used to define 'social acceptability' are examined for validity. Results show firstly the cross contrast between the hospital's expectation and the nurses' wishes with regard to working hours. Furthermore, inspite of the demand for flexibility, staff have very little choice and there is little sign of joint decision making. Thirdly results show that health, interpersonal and social aspects are of special importance and that, correspondingly, in the view of nurses, financial and practical problems are of lesser importance in their every day life.

  12. Nuclear Energy and Public Acceptance

    International Nuclear Information System (INIS)

    Daifuku, K.

    2002-01-01

    The continued use of nuclear power in the European Union and elsewhere requires an adequate level of public and political acceptance. A lack of acceptance is often mistakenly cited as a reason for the slowdown in nuclear power plant construction in Western Europe and as a justification for abandoning nuclear power. In fact, the reasons for the slowdown have more to do with the following two factors: Plentiful supplies of low-priced natural gas, making gas-fired power plants a more attractive investment choice; more than adequate supplies of electricity which have curbed the need for the construction of new plant of any kind. In general, moves towards a withdrawal from nuclear in certain Community countries have been due to party political pressures and have not been a response to public opposition to nuclear. In addition, opinion polls do not show widespread public opposition to the use of nuclear power. Figures consistently indicate that the use of nuclear power does not come high on the list of most people's main worries. Their main concerns focus on other issues such as crime and financial problems. In the main, electricity is taken for granted in the industrialised world. Electric power only becomes an issue when there is a threat of shortages. So if public acceptance is not the main obstacle, what is? Political acceptance is an integral part of the process in which nuclear becomes acceptable or not. The relationship between public and political acceptance and the role of the industry in this context, on how to foster a better trialogue, will be examined. (author)

  13. Patient acceptance of awake craniotomy.

    Science.gov (United States)

    Wrede, Karsten H; Stieglitz, Lennart H; Fiferna, Antje; Karst, Matthias; Gerganov, Venelin M; Samii, Madjid; von Gösseln, Hans-Henning; Lüdemann, Wolf O

    2011-12-01

    The aim of this study was to objectively assess the patients' acceptance for awake craniotomy in a group of neurosurgical patients, who underwent this procedure for removal of lesions in or close to eloquent brain areas. Patients acceptance for awake craniotomy under local anesthesia and conscious sedation was assessed by a formal questionnaire (PPP33), initially developed for general surgery patients. The results are compared to a group of patients who had brain surgery under general anesthesia and to previously published data. The awake craniotomy (AC) group consisted of 37 male and 9 female patients (48 craniotomies) with age ranging from 18 to 71 years. The general anesthesia (GA) group consisted of 26 male and 15 female patients (43 craniotomies) with age ranging from 26 to 83 years. All patients in the study were included in the questionnaire analysis. In comparison to GA the overall PPP33 score for AC was higher (p=0.07), suggesting better overall acceptance for AC. The subscale scores for AC were also significantly better compared to GA for the two subscales "postoperative pain" (p=0.02) and "physical disorders" (p=0.01) and equal for the other 6 subscales. The results of the overall mean score and the scores for the subscales of the PPP33 questionnaire verify good patients' acceptance for AC. Previous studies have shown good patients' acceptance for awake craniotomy, but only a few times using formal approaches. By utilizing a formal questionnaire we could verify good patient acceptance for awake craniotomy for the treatment of brain tumors in or close to eloquent areas. This is a novel approach that substantiates previously published experiences. Copyright © 2011 Elsevier B.V. All rights reserved.

  14. Principles and Criteria for Design

    DEFF Research Database (Denmark)

    Beghin, D.; Cervetto, D.; Hansen, Peter Friis

    1997-01-01

    The mandate of ISSC Committee IV.1 on principles and Criteria for Design is to report on the following:The ongoing concern for quantification of general economic and safety criteria for marine structures and for the development of appropriate principles for rational life cycle design using...

  15. Diagnostic criteria for vascular dementia

    NARCIS (Netherlands)

    Scheltens, P.; Hijdra, A. H.

    1998-01-01

    The term vascular dementia implies the presence of a clinical syndrome (dementia) caused by, or at least assumed to be caused by, a specific disorder (cerebrovascular disease). In this review, the various sets of criteria used to define vascular dementia are outlined. The various sets of criteria

  16. Criteria for controlled atmosphere chambers

    International Nuclear Information System (INIS)

    Robinson, J.N.

    1980-03-01

    The criteria for design, construction, and operation of controlled atmosphere chambers intended for service at ORNL are presented. Classification of chambers, materials for construction, design criteria, design, controlled atmosphere chamber systems, and operating procedures are presented. ORNL Safety Manual Procedure 2.1; ORNL Health Physics Procedure Manual Appendix A-7; and Design of Viewing Windows are included in 3 appendices

  17. Text recycling: acceptable or misconduct?

    Science.gov (United States)

    Harriman, Stephanie; Patel, Jigisha

    2014-08-16

    Text recycling, also referred to as self-plagiarism, is the reproduction of an author's own text from a previous publication in a new publication. Opinions on the acceptability of this practice vary, with some viewing it as acceptable and efficient, and others as misleading and unacceptable. In light of the lack of consensus, journal editors often have difficulty deciding how to act upon the discovery of text recycling. In response to these difficulties, we have created a set of guidelines for journal editors on how to deal with text recycling. In this editorial, we discuss some of the challenges of developing these guidelines, and how authors can avoid undisclosed text recycling.

  18. Toward an acceptable nuclear future

    International Nuclear Information System (INIS)

    Weinberg, A.M.

    1977-11-01

    The nuclear option is in danger of being foreclosed. The trend toward antinuclearism may be reversed if concerns about low-level radiation insult can be shown ultimately to be without foundation; evidence for this speculation is presented. Nevertheless it is suggested that the nuclear enterprise itself must propose new initiatives to increase the acceptability of nuclear energy. A key element of an acceptable nuclear future is cluster siting of reactors. This siting plan might be achieved by confining new reactors essentially to existing sites

  19. Failure Criteria for Reinforced Materials

    DEFF Research Database (Denmark)

    Rathkjen, Arne

    Failure of materials is often characterized as ductile yielding, brittle fracture, creep rupture, etc., and different criteria given in terms of different parameters have been used to describe different types of failure. Only criteria expressing failure in terms of stress are considered in what...... place until the matrix, the continuous component of the composite, fails. When an isotropic matrix is reinforced as described above, the result is an anisotropic composite material. Even if the material is anisotropic, it usually exhibits a rather high degree of symmetry and such symmetries place...... certain restrictions on the form of the failure criteria for anisotropic materials. In section 2, some failure criteria for homogenous materials are reviewed. Both isotropic and anisotropic materials are described, and in particular the constraints imposed on the criteria from the symmetries orthotropy...

  20. Frequency limitations on reactor release derived from radiological criteria

    International Nuclear Information System (INIS)

    Clarke, R.H.

    1976-05-01

    Acceptable frequencies are suggested with which a number of defined individual and collective dose criteria are met. This has enabled a relationship to be proposed between the frequency and any event leading to release of radioactive material and the dose commitment to the hypothetical individual at the site boundary. The philosphy developed is generally applicable, but in this instance it has been demonstrated for an SGHW Reactor located at Sizewell. The results are derived on the basis of an acceptable level of risk of fatality to the most exposed individual and the application of the methodology to other reactor types and sites is demonstrated. (author)

  1. Criteria impacting shipments of Rocky Flats Plant radioactive mixed wastes

    International Nuclear Information System (INIS)

    Clawson, R.L.; Eide, J.H.

    1992-05-01

    Westinghouse Hanford Company, Transportation and Packaging Division, under contract for the Los Alamos Technology Office-Rocky Flats Plant, has developed this synopsis report to be used as a reference in the development of the Rocky Flats Plant Comprehensive Treatment and Management Plan and the Rocky Flats Plant Residue Elimination Plan. This report represents the criteria for packaging, shipping, and transporting Rocky Flats Plant radioactive mixed wastes. It is a compilation of state and federal regulations, US Department of Energy orders, and acceptance criteria specific to US Department of Energy radioactive mixed waste treatment, storage and disposal facilities

  2. Nitrogen trailer acceptance test report

    International Nuclear Information System (INIS)

    Kostelnik, A.J.

    1996-01-01

    This Acceptance Test Report documents compliance with the requirements of specification WHC-S-0249. The equipment was tested according to WHC-SD-WM-ATP-108 Rev.0. The equipment being tested is a portable contained nitrogen supply. The test was conducted at Norco's facility

  3. Consumer Acceptability Of Irradiated Foods

    International Nuclear Information System (INIS)

    Awoyinka, A.; Akingbohungbe, A.E.

    1994-01-01

    Three commonly used food items; maize, beans and smoked fish were irradiated and consumer acceptability was tested through a questionnaire method. Subjects were residents in Ile-Ife, Nigeria. Respondents attitudes towards the processing and tasting of the food were very positive and the possibility of marketing the foods was suggested by them

  4. W-025, acceptance test report

    International Nuclear Information System (INIS)

    Roscha, V.

    1994-01-01

    This acceptance test report (ATR) has been prepared to establish the results of the field testing conducted on W-025 to demonstrate that the electrical/instrumentation systems functioned as intended by design. This is part of the RMW Land Disposal Facility

  5. Safety culture and public acceptance

    International Nuclear Information System (INIS)

    Mikhalevich, Alexander A.

    2002-01-01

    After the Chernobyl NPP accident a public acceptance has become a key factor in nuclear power development all over the world. Therefore, nuclear safety culture should be based not only on technical principles, responsibilities, supervision, regulatory provisions, emergency preparedness, but the public awareness of minimum risk during the operation and decommissioning of NPPs, radioactive waste management, etc. (author)

  6. Euthanasia Acceptance: An Attitudinal Inquiry.

    Science.gov (United States)

    Klopfer, Fredrick J.; Price, William F.

    The study presented was conducted to examine potential relationships between attitudes regarding the dying process, including acceptance of euthanasia, and other attitudinal or demographic attributes. The data of the survey was comprised of responses given by 331 respondents to a door-to-door interview. Results are discussed in terms of preferred…

  7. AAL- technology acceptance through experience

    NARCIS (Netherlands)

    Huldtgren, A.; Ascencio San Pedro, G.; Pohlmeyer, A.E.; Romero Herrera, N.A.

    2014-01-01

    Despite substantial research and development of Ambient Assisted Living (AAL) technologies, their acceptance remains low. This is partially caused by a lack of accounting for users' needs and values, and the social contexts these systems are to be embedded in. Participatory design has some potential

  8. Energy justice: Participation promotes acceptance

    Science.gov (United States)

    Baxter, Jamie

    2017-08-01

    Wind turbines have been a go-to technology for addressing climate change, but they are increasingly a source of frustration for all stakeholders. While community ownership is often lauded as a panacea for maximizing turbine acceptance, a new study suggests that decision-making involvement — procedural fairness — matters most.

  9. Worldwide nuclear revival and acceptance

    International Nuclear Information System (INIS)

    Geraets, Luc H.; Crommelynck, Yves A.

    2010-01-01

    The paper outlines the current status and trends of the nuclear revival in Europe and abroad, the evolution of the public opinion in the last decade, and the interaction between the former and the latter. It emphasises the absolute priority of a professional communication and exchange to gain public acceptance. (orig.)

  10. Analysing and Comparing Encodability Criteria

    Directory of Open Access Journals (Sweden)

    Kirstin Peters

    2015-08-01

    Full Text Available Encodings or the proof of their absence are the main way to compare process calculi. To analyse the quality of encodings and to rule out trivial or meaningless encodings, they are augmented with quality criteria. There exists a bunch of different criteria and different variants of criteria in order to reason in different settings. This leads to incomparable results. Moreover it is not always clear whether the criteria used to obtain a result in a particular setting do indeed fit to this setting. We show how to formally reason about and compare encodability criteria by mapping them on requirements on a relation between source and target terms that is induced by the encoding function. In particular we analyse the common criteria full abstraction, operational correspondence, divergence reflection, success sensitiveness, and respect of barbs; e.g. we analyse the exact nature of the simulation relation (coupled simulation versus bisimulation that is induced by different variants of operational correspondence. This way we reduce the problem of analysing or comparing encodability criteria to the better understood problem of comparing relations on processes.

  11. 46 CFR 164.019-7 - Non-standard components; acceptance criteria and procedures.

    Science.gov (United States)

    2010-10-01

    ... must include a description of the quality control procedures that will be in effect during production... oversight of the manufacturer's program of production quality control, including a description of the... the case of textiles. (5) The request must include a list of all materials used in the construction of...

  12. On the assessment of marginal life saving costs for risk acceptance criteria

    DEFF Research Database (Denmark)

    Fischer, Katharina; Virguez, Edgar; Sánchez-Silva, Mauricio

    2013-01-01

    : The definition of the marginal life saving costs, the discount rate used for comparing costs and benefits that accrue at different points in time and the time horizon over which future consequences of the decision are taken into account. In the present paper these issues are discussed based on a clear...

  13. Statistical approach for derivation of quantitative acceptance criteria for radioactive wastes to near surface disposal facility

    International Nuclear Information System (INIS)

    Park, Jin Beak; Park, Joo Wan; Lee, Eun Yong; Kim, Chang Lak

    2003-01-01

    For reference human intrusion scenarios constructed in previous study, a probabilistic safety assessment to derive the radionuclide concentration limits for the low- and intermediate- level radioactive waste disposal facility is conducted. Statistical approach by the latin hypercube sampling method is introduced and new assumptions about the disposal facility system are examined and discussed. In our previous study of deterministic approach, the post construction scenarios appeared as most limiting scenario to derive the radionuclide concentration limits. Whereas, in this statistical approach, the post drilling and the post construction scenarios are mutually competing for the scenario selection according to which radionuclides are more important in safety assessment context. Introduction of new assumption shows that the post drilling scenario can play an important role as the limiting scenario instead of the post-construction scenario. When we compare the concentration limits between the previous and this study, concentrations of radionuclides such as Nb-94, Cs-137 and alpha-emitting radionuclides show elevated values than the case of the previous study. Remaining radionuclides such as Sr-90, Tc-99 I-129, Ni-59 and Ni-63 show lower values than the case of the previous study

  14. Development of acceptance criteria and damage tolerance analyzes of the ductile iron insert

    International Nuclear Information System (INIS)

    Dillstroem, Peter; Alverlind, Lars; Andersson, Magnus

    2010-01-01

    SKB intends to qualify a test system for detection and sizing of defects deemed to be relevant to the ductile iron insert. In support of this qualification, a damage tolerance analysis indicating the current qualification targets, given assumed damage and failure modes. This report describes the damage tolerance analyzes of different types of defects that are considered relevant of the ductile iron insert. The results are reported separately for each test area (zone) and type of insert (BWRs and PWRs)

  15. Status of ECCS Acceptance Criteria Revision in U. S. NRC and Perspective

    International Nuclear Information System (INIS)

    Lee, Joosuk; Woo, Swengwoong

    2013-01-01

    Subsequently the NRC had conducted a fuel cladding research program to investigate the behavior of high burnup fuel cladding under LOCA conditions. This research program conducted at Argonne National Laboratory (ANL), as well as conducted as jointly-funded programs at the Kurchatov Institute and the Halden Reactor. From these programs, several important technical findings, listed in following section, for rule revision were obtained. On March 14, 2000, the Nuclear Energy Institute (NEI) submitted a petition for rulemaking (PRM) requesting that the NRC amend its regulations in 50.44 and 50.46 (PRM 50-71). The NEI petition stated that these regulations apply to only two specific zirconium-alloy fuel cladding materials (zircaloy and ZIRLO TM ). The NRC resolved PRM-50-71 by deciding that it should be considered in the following rulemaking process. Meanwhile, on March 15, 2007, Mark Leyse submitted a PRM to the NRC (PRM 50-84). The petitioner requests that the NRC conduct rulemaking in the following areas: Establish regulations that require licensees to operate light-water power reactors under conditions that are effective in limiting the thickness of crud and/or oxide layers. Amend Appendix K to Part 50 to explicitly require that steady-state temperature distribution and stored energy in the reactor fuel at the onset of a postulated LOCA be calculated by factoring in the role of the thermal resistance of crud and oxide layers. Amend 50.46 to specify a maximum allowable percentage of hydrogen content in the cladding. The NRC resolved PRM-50-84 by deciding that the petitioner's issues should be considered in the rulemaking process. On August 13, 2009, the NRC published an Advance Notice of Proposed Rulemaking (ANPR) to obtain stakeholder views on issues associated with amending 50.46. On March 1, 2012, and subsequently modified by the staff's June 1, 2012, SECY-12-0034 was submitted to the Commission to obtain approval to publish for public comment, and it was approved on January 7, 2013 with some amendments

  16. Bioethical perspective on acceptable-risk criteria for nuclear-waste management

    International Nuclear Information System (INIS)

    Maxey, M.N.

    1977-01-01

    Wisely managing the profound human and environmental risks of nuclear wastes requires complex moral and ethical judgments. Whereas traditional ethics is limited to interpersonal relations, a new system of ethics--bioethics--concerns man's relation with nature. Environmentalists claim that technology has upset the balance of nature, that nature is sacred and has inviolable rights, and that man must therefore regulate his behavior to conform to earth's limited carrying capacity. They also say that Judeo-Christian monotheism and anthropocentrism have sanctioned the exploitation of nature in the West, whereas Eastern religions teach adaptation to nature. Evidence suggests, however, that the balance of nature is neither absolute nor precarious, but is continually changing. Moreover, technology has brought more good than harm to man, and man's needs should supersede nature's. Other evidence indicates that the earth's resources may be neither limited nor nearly exhausted. Persuasive arguments also demonstrate that man's relation with nature is not traceable to religious assumptions. In assessing the risks/benefits of nuclear-waste management, we should avoid risks that jeopardize the rights of future generations without imposing excessive sacrifices on the present generation

  17. 77 FR 51880 - Requirements for Maintenance of Inspections, Tests, Analyses, and Acceptance Criteria

    Science.gov (United States)

    2012-08-28

    ....regulations.gov and search for Docket ID NRC-2010-0012. NRC's Agencywide Documents Access and Management... Program for ITAAC Management,'' which provides guidance to verify that licensees have implemented ITAAC.... Rather, the NRC would use a holistic review using results from the NRC's construction inspection program...

  18. 76 FR 27925 - Requirements for Maintenance of Inspections, Tests, Analyses, and Acceptance Criteria

    Science.gov (United States)

    2011-05-13

    ... and Management System (ADAMS) and other methods for obtaining publicly available documents related to... issued Inspection Procedure 40600, ``Licensee Program for ITAAC Management,'' that provides guidance to..., as a primary basis for the 10 CFR 52.103(g) finding. Rather, the NRC would use a holistic review...

  19. Microneedle characterisation: the need for universal acceptance criteria and GMP specifications when moving towards commercialisation.

    Science.gov (United States)

    Lutton, Rebecca E M; Moore, Jessica; Larrañeta, Eneko; Ligett, Stephen; Woolfson, A David; Donnelly, Ryan F

    2015-08-01

    With interest in microneedles as a novel drug transdermal delivery system increasing rapidly since the late 1990s (Margetts and Sawyer Contin Educ Anaesthesia Crit Care Pain. 7(5):171-76, 2007), a diverse range of microneedle systems have been fabricated with varying designs and dimensions. However, there are still very few commercially available microneedle products. One major issue regarding microneedle manufacture on an industrial scale is the lack of specific quality standards for this novel dosage form in the context of Good Manufacturing Practice (GMP). A range of mechanical characterisation tests and microneedle insertion analysis techniques are used by researchers working on microneedle systems to assess the safety and performance profiles of their various designs. The lack of standardised tests and equipment used to demonstrate microneedle mechanical properties and insertion capability makes it difficult to directly compare the in use performance of candidate systems. This review highlights the mechanical tests and insertion analytical techniques used by various groups to characterise microneedles. This in turn exposes the urgent need for consistency across the range of microneedle systems in order to promote innovation and the successful commercialisation of microneedle products.

  20. Status of ECCS Acceptance Criteria Revision in U. S. NRC and Perspective

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Joosuk; Woo, Swengwoong [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2013-05-15

    Subsequently the NRC had conducted a fuel cladding research program to investigate the behavior of high burnup fuel cladding under LOCA conditions. This research program conducted at Argonne National Laboratory (ANL), as well as conducted as jointly-funded programs at the Kurchatov Institute and the Halden Reactor. From these programs, several important technical findings, listed in following section, for rule revision were obtained. On March 14, 2000, the Nuclear Energy Institute (NEI) submitted a petition for rulemaking (PRM) requesting that the NRC amend its regulations in 50.44 and 50.46 (PRM 50-71). The NEI petition stated that these regulations apply to only two specific zirconium-alloy fuel cladding materials (zircaloy and ZIRLO{sup TM}). The NRC resolved PRM-50-71 by deciding that it should be considered in the following rulemaking process. Meanwhile, on March 15, 2007, Mark Leyse submitted a PRM to the NRC (PRM 50-84). The petitioner requests that the NRC conduct rulemaking in the following areas: Establish regulations that require licensees to operate light-water power reactors under conditions that are effective in limiting the thickness of crud and/or oxide layers. Amend Appendix K to Part 50 to explicitly require that steady-state temperature distribution and stored energy in the reactor fuel at the onset of a postulated LOCA be calculated by factoring in the role of the thermal resistance of crud and oxide layers. Amend 50.46 to specify a maximum allowable percentage of hydrogen content in the cladding. The NRC resolved PRM-50-84 by deciding that the petitioner's issues should be considered in the rulemaking process. On August 13, 2009, the NRC published an Advance Notice of Proposed Rulemaking (ANPR) to obtain stakeholder views on issues associated with amending 50.46. On March 1, 2012, and subsequently modified by the staff's June 1, 2012, SECY-12-0034 was submitted to the Commission to obtain approval to publish for public comment, and it was approved on January 7, 2013 with some amendments.

  1. Mark II containment program load evaluation and acceptance criteria; Generic Technical Activity A-8

    International Nuclear Information System (INIS)

    Anderson, C.J.

    1981-08-01

    The report provides a discussion of LOCA-related suppression pool hydrodynamic loads in boiling water reactor (BWR) facilities with the Mark II pressure-suppression containment design. This report concludes NRC Generic Technical Activity A-8, 'Mark II Containment Pool Dynamic Loads,' which has been designated an 'Unresolved Safety Issue' pursuant to Section 210 of the Energy Reorganization Act of 1974

  2. Bioethical perspective on acceptable-risk criteria for nuclear-waste management

    Energy Technology Data Exchange (ETDEWEB)

    Maxey, M.N.

    1977-07-15

    Wisely managing the profound human and environmental risks of nuclear wastes requires complex moral and ethical judgments. Whereas traditional ethics is limited to interpersonal relations, a new system of ethics--bioethics--concerns man's relation with nature. Environmentalists claim that technology has upset the balance of nature, that nature is sacred and has inviolable rights, and that man must therefore regulate his behavior to conform to earth's limited carrying capacity. They also say that Judeo-Christian monotheism and anthropocentrism have sanctioned the exploitation of nature in the West, whereas Eastern religions teach adaptation to nature. Evidence suggests, however, that the balance of nature is neither absolute nor precarious, but is continually changing. Moreover, technology has brought more good than harm to man, and man's needs should supersede nature's. Other evidence indicates that the earth's resources may be neither limited nor nearly exhausted. Persuasive arguments also demonstrate that man's relation with nature is not traceable to religious assumptions. In assessing the risks/benefits of nuclear-waste management, we should avoid risks that jeopardize the rights of future generations without imposing excessive sacrifices on the present generation.

  3. Selection criteria of residents for residency programs in Kuwait.

    Science.gov (United States)

    Marwan, Yousef; Ayed, Adel

    2013-01-19

    In Kuwait, 21 residency training programs were offered in the year 2011; however, no data is available regarding the criteria of selecting residents for these programs. This study aims to provide information about the importance of these criteria. A self-administered questionnaire was used to collect data from members (e.g. chairmen, directors, assistants …etc.) of residency programs in Kuwait. A total of 108 members were invited to participate. They were asked to rate the importance level (scale from 1 to 5) of criteria that may affect the acceptance of an applicant to their residency programs. Average scores were calculated for each criterion. Of the 108 members invited to participate, only 12 (11.1%) declined to participate. Interview performance was ranked as the most important criteria for selecting residents (average score: 4.63/5.00), followed by grade point average (average score: 3.78/5.00) and honors during medical school (average score: 3.67/5.00). On the other hand, receiving disciplinary action during medical school and failure in a required clerkship were considered as the most concerning among other criteria used to reject applicants (average scores: 3.83/5.00 and 3.54/5.00 respectively). Minor differences regarding the importance level of each criterion were noted across different programs. This study provided general information about the criteria that are used to accept/reject applicants to residency programs in Kuwait. Future studies should be conducted to investigate each criterion individually, and to assess if these criteria are related to residents' success during their training.

  4. Retrospective analysis of 'gamma distribution' based IMRT QA criteria

    International Nuclear Information System (INIS)

    Wen, C.; Chappell, R.A.

    2010-01-01

    Full text: IMRT has been implemented into clinical practice at Royal Hobart Hospital (RHH) since mid 2006 for treating patients with Head and Neck (H and N) or prostate tumours. A local quality assurance (QA) acceptance criteria based on 'gamma distribution' for approving IMRT plan was developed and implemented in early 2007. A retrospective analysis of such criteria over 194 clinical cases will be presented. The RHH IMRT criteria was established with assumption that gamma distribution obtained through inter-comparison of 2 D dose maps between planned and delivered was governed by a positive-hail' normal distribution. A commercial system-MapCheck was used for 2 D dose map comparison with a built-in gamma analysis tool. Gamma distribution histogram was generated and recorded for all cases. By retrospectively analysing those distributions using curve fitting technique, a statistical gamma distribution can be obtained and evaluated. This analytical result can be used for future IMRT planing and treatment delivery. The analyses indicate that gamma distribution obtained through MapCheckTM is well under the normal distribution, particularly for prostate cases. The applied pass/fail criteria is not overly sensitive to identify 'false fails' but can be further tighten-up for smaller field while for larger field found in both H and N and prostate cases, the criteria was correctly applied. Non-uniform distribution of detectors in MapCheck and experience level of planners are two major factors to variation in gamma distribution among clinical cases. This criteria derived from clinical statistics is superior and more accurate than single-valued criteria for lMRT QA acceptance procedure. (author)

  5. Study of Validity Criteria for Radionuclide-Analysis of Low- and Intermediate-Level Radioactive Waste

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ji Uk; Baek, Hyun Suk; Jeong, Sung Yeop [Sungwoo E and T Co., Hanam (Korea, Republic of); Shin, Seung Kyu [Korea Radioactive waste Management Corporation, Gyeongju (Korea, Republic of)

    2013-05-15

    Literature survey on the deviation of the measuring equipment and statistical analysis on the measured data of domestic LILW were performed in order to set evaluation criteria quantitatively when comparing the result of each test and inspections. This study provided opportunity to increase credibility and re-assure validity of Waste Acceptance Criteria (WAC). Through the statistical analysis for deviation of measurement by comparing repository inspection with generator self-test, the quantitative acceptance criteria were set depending on specific activity of Co-60 and Cs-137. The acceptance criteria is a relative bias of KRMC result to generator result and set from low 50 % to high 150 % for Co-60, from low 30 % to 250 % for Cs-137. In this study, because the statistical analysis results of the waste drum assay are not enough representing whole range specified at WAC, an additional research that include characteristic analysis of LILW generated other birthplace should be done.

  6. Microbiological criteria for good manufacturing practice (GMP)

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, J [Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary); Zukal, E [Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary)

    1992-01-01

    Good manufacturing practice (GMP) consist of an effective manufacturing operation and an effective application of food control. GMP is best supported by the Hazard Analysis Critical Control Point system (HACCP) of the preventive quality assurance, which requires that food irradiation as any food processing technology should be used only with foods of an acceptable quality and adequate handling and storage procedures should precede and follow the processing. The paper concentrates on the first element of the HACCP system for an irradiation plant: the incoming product control, i.e. whether GMP of foods to be irradiated can be assessed by establishing microbiological criteria for their previous good manufacturing practice. In this regard, it summarizes considerations and findings of a ''Consultation on Microbiological Criteria for Foods to be Further Processed Including by Irradiation'' held in 1989 by the International Consultative Group on Food irradiation at the Headquarters of the World Health Organization, Geneva. Difficulties in establishing reference values and defining good manufacturing practices will be pointed out. (orig.)

  7. Decommissioning of nuclear facilities using current criteria

    International Nuclear Information System (INIS)

    Shum, E.Y.; Swift, J.J.; Malaro, J.C.

    1991-01-01

    When a licensed nuclear facility ceases operation, the US Nuclear Regulatory Commission (NRC) is responsible for ensuring that the facility and its site are decontaminated to an acceptable level so that it is safe to release that facility and site for unrestricted public use. Currently, the NRC is developing decommissioning criteria based on reducing public doses from residual contamination in soils and structures at sites released for unrestricted use to as low as is reasonably achievable (ALARA). Plans are to quantify ALARA in terms of an annual total effective dose equivalent (TEDE) to an average member of the most highly exposed population group. The NRC is working on a regulatory guidance document to provide a technical basis for translating residual contamination levels to annual dose levels. Another regulatory guide is being developed to provide guidance to the licensee on how to conduct radiological surveys to demonstration compliance with the NRC decommissioning criteria. The methods and approaches used in these regulatory guides on the decommissioning of a nuclear facility are discussed in the paper

  8. Criteria Considerations for Establishment of Hems Operations

    Directory of Open Access Journals (Sweden)

    Borivoj Galović

    2007-05-01

    Full Text Available The importance of the "golden hour"; for optimal efficiencyof helicopter operations in emergency medical service (HEMSto meet the "golden hour" requirement the unconditional requirementis to establish a net of operational units to cover theentire area of the Republic of Croatia, capable to operate withinwide integrated area (international services. It is additionalback-up, not a competition to road and sea EMS vehicles. Therequired standards; HEMS operation, following complementarytraffic policy, i. e. complementary policy in line of trafficsystem integration within wider region, with reference to standards,must entirely comply with globally accepted standards.Republic of Croatia 's obvious objectives are traffic integrationinto EU (European Union traffic system. Cost analyses; It isstressed that coherent traffic policy can by certain instrumentsreduce traffic assigned external cost in national budget. Significanttraffic external cost includes cost of traffic accidents, environmentimpacts and traffic jams, and could be reduced byestablishmentof multi-purpose helicopter operations. SWOTanalyses should be made as for any other strategy or project.Technical-technological criteria and other considerations;Considering technical-technological criteria for relief of criticalsituations in traffic, it is obvious that one helicopter type cannotcomply to all multi-purpose requirements that traffic sets beforeus - EMS on open roads, sea, mountains and urban trafficcongested area, and search and rescue operations. However,common factor for all types is compliance to global standardsand regulations. In the paper, some examples of HEMS operationsin the EU States are mentioned.

  9. Criteria for high-level waste disposal

    International Nuclear Information System (INIS)

    Sousselier, Y.

    1981-01-01

    Disposal of radioactive wastes is storage without the intention of retrieval. But in such storage, it may be useful and in some cases necessary to have the possibility of retrieval at least for a certain period of time. In order to propose some criteria for HLW disposal, one has to examine how this basic concept is to be applied. HLW is waste separated as a raffinate in the first cycle of solvent extraction in reprocessing. Such waste contains the bulk of fission products which have long half lives, therefore the safety of a disposal site, at least after a certain period of time, must be intrinsic, i.e. not based on human intervention. There is a consensus that such a disposal is feasible in a suitable geological formation in which the integrity of the container will be reinforced by several additional barriers. Criteria for disposal can be proposed for all aspects of the question. The author discusses the aims of the safety analysis, particularly the length of time for this analysis, and the acceptable dose commitments resulting from the release of radionuclides, the number and role of each barrier, and a holistic analysis of safety external factors. (Auth.)

  10. Microbiological criteria for good manufacturing practice (GMP)

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, J. (Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary)); Zukal, E. (Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary))

    1992-01-01

    Good manufacturing practice (GMP) consist of an effective manufacturing operation and an effective application of food control. GMP is best supported by the Hazard Analysis Critical Control Point system (HACCP) of the preventive quality assurance, which requires that food irradiation as any food processing technology should be used only with foods of an acceptable quality and adequate handling and storage procedures should precede and follow the processing. The paper concentrates on the first element of the HACCP system for an irradiation plant: the incoming product control, i.e. whether GMP of foods to be irradiated can be assessed by establishing microbiological criteria for their previous good manufacturing practice. In this regard, it summarizes considerations and findings of a ''Consultation on Microbiological Criteria for Foods to be Further Processed Including by Irradiation'' held in 1989 by the International Consultative Group on Food irradiation at the Headquarters of the World Health Organization, Geneva. Difficulties in establishing reference values and defining good manufacturing practices will be pointed out. (orig.)

  11. Design criteria for piping and nozzles program

    International Nuclear Information System (INIS)

    Moore, S.E.; Bryson, J.W.

    1977-01-01

    This report reviews the activities and accomplishments of the Design Criteria for Piping and Nozzles program being conducted by the Oak Ridge National Laboratory for the period July 1, 1975, to September 30, 1976. The objectives of the program are to conduct integrated experimental and analytical stress analysis studies of piping system components and isolated and closely-spaced pressure vessel nozzles in order to confirm and/or improve the adequacy of structural design criteria and analytical methods used to assure the safe design of nuclear power plants. Activities this year included the development of a finite-element program for analyzing two closely spaced nozzles in a cylindrical pressure vessel; a limited-parameter study of vessels with isolated nozzles, finite-element studies of piping elbows, a fatigue test of an out-of-round elbow, summary and evaluation of experimental studies on the elastic-response and fatigue failure of tees, parameter studies on the behavior of flanged joints, publication of fifteen topical reports and papers on various experimental and analytical studies; and the development and acceptance of a number of design rules changes to the ASME Code. 2 figures, 2 tables

  12. Microbiological criteria for good manufacturing practice (GMP)

    International Nuclear Information System (INIS)

    Farkas, J.; Zukal, E.

    1992-01-01

    Good manufacturing practice (GMP) consist of an effective manufacturing operation and an effective application of food control. GMP is best supported by the Hazard Analysis Critical Control Point system (HACCP) of the preventive quality assurance, which requires that food irradiation as any food processing technology should be used only with foods of an acceptable quality and adequate handling and storage procedures should precede and follow the processing. The paper concentrates on the first element of the HACCP system for an irradiation plant: the incoming product control, i.e. whether GMP of foods to be irradiated can be assessed by establishing microbiological criteria for their previous good manufacturing practice. In this regard, it summarizes considerations and findings of a ''Consultation on Microbiological Criteria for Foods to be Further Processed Including by Irradiation'' held in 1989 by the International Consultative Group on Food irradiation at the Headquarters of the World Health Organization, Geneva. Difficulties in establishing reference values and defining good manufacturing practices will be pointed out. (orig.) [de

  13. The use of economic criteria in providing a basis for safe reactor operation

    International Nuclear Information System (INIS)

    Graham, J.

    1989-01-01

    Probabilistic criteria based upon an acceptance measure of protection for owner investment can complete the range of design probabilistic criteria between those set by acceptance public safety and those set by acceptable reliability in plant operation. Criteria which address the protection of owner investment have the benefit of lowering risk in adjacent risk regions by providing greater reliability in operation as well as less risk to the safety of the public and the environment. Such investment protection criteria are currently being used to extend plant life but they could also be used very beneficially as part of the initial design process. In this paper trial criteria are suggested which address the risk of extended plant shutdown with the resultant necessity to purchase replacement power, and the risk of replacement of expensive plant components. Additional financial assessment is required to ensure that there is a proper correlation between acceptable measures of owner-investment protection and the levels of probabilistic defence suggested, but the trial criteria proposed can be used as important practical design criteria

  14. AAPT Diagnostic Criteria for Chronic Cancer Pain Conditions

    OpenAIRE

    Paice, Judith A.; Mulvey, Matt; Bennett, Michael; Dougherty, Patrick M.; Farrar, John T.; Mantyh, Patrick W.; Miaskowski, Christine; Schmidt, Brian; Smith, Thomas J.

    2016-01-01

    Chronic cancer pain is a serious complication of malignancy or its treatment. Currently, no comprehensive, universally accepted cancer pain classification system exists. Clarity in classification of common cancer pain syndromes would improve clinical assessment and management. Moreover, an evidence-based taxonomy would enhance cancer pain research efforts by providing consistent diagnostic criteria, ensuring comparability across clinical trials. As part of a collaborative effort between the A...

  15. Aquatic Life Criteria - Tributyltin (TBT)

    Science.gov (United States)

    Documents pertaining to 2004 Final Acute and Chronic Ambient Aquatic Life Water Quality Criteria for Tributyltin (TBT) for freshwater and saltwater. These documents include the safe levels of TBT that should protect the majority of species.

  16. Floorball game skills (evaluation criteria)

    OpenAIRE

    Chlumský, Marek

    2013-01-01

    Title: Playing skills in floorball (evaluation criteria). Target: To create a list of playing skills which an ideal player should demonstrate. Find and verify the evaluation criteria of these skills and inspire trainers to develop these skills in the best way. Methods: Informal interviews, individually structured interviews, analysis and verification of data, pilot testing. Results: Defined playing skills in floorball, developed scale of values of floorball playing skills, creation of exercis...

  17. Reliability criteria for voltage stability

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Carson W; Silverstein, Brian L [Bonneville Power Administration, Portland, OR (United States)

    1994-12-31

    In face of costs pressures, there is need to allocate scare resources more effectively in order to achieve voltage stability. This naturally leads to development of probabilistic criteria and notions of rick management. In this paper it is presented a discussion about criteria for long term voltage stability limited to the case in which the time frames are topically several minutes. (author) 14 refs., 1 fig.

  18. Food irradiation receives international acceptance

    Energy Technology Data Exchange (ETDEWEB)

    Beddoes, J M [Atomic Energy of Canada Ltd., Ottawa, Ontario. Commercial Products

    1982-04-01

    Irradiation has advantages as a method of preserving food, especially in the Third World. The author tabulates some examples of actual use of food irradiation with dates and tonnages, and tells the story of the gradual acceptance of food irradiation by the World Health Organization, other international bodies, and the U.S. Food and Drug Administration (USFDA). At present, the joint IAEA/FAO/WHO standard permits an energy level of up to 5 MeV for gamma rays, well above the 1.3 MeV energy level of /sup 60/Co. The USFDA permits irradiation of any food up to 10 krad, and minor constituents of a diet may be irradiated up to 5 Mrad. The final hurdle to be cleared, that of economic acceptance, depends on convincing the food processing industry that the process is technically and economically efficient.

  19. Consumer acceptance of irradiated food

    Energy Technology Data Exchange (ETDEWEB)

    Loaharanu, P [Head, Food Preservation Section, Joint FAO/ IAEA Division of Nuclear Techniques in Food and Agriculture, Wagramerstr. 5, A-1400, Vienna (Austria)

    1998-12-31

    There was a widely held opinion during the 1970`s and 1980`s that consumers would be reluctant to purchase irradiated food, as it was perceived that consumers would confuse irradiated food with food contaminated by radionuclides. Indeed, a number of consumer attitude surveys conducted in several western countries during these two decades demonstrated that the concerns of consumers on irradiated food varied from very concerned to seriously concerned.This paper attempts to review parameters conducting in measuring consumer acceptance of irradiated food during the past three decades and to project the trends on this subject. It is believed that important lessons learned from past studies will guide further efforts to market irradiated food with wide consumer acceptance in the future. (Author)

  20. Consumer acceptance of irradiated food

    Energy Technology Data Exchange (ETDEWEB)

    Loaharanu, P. [Head, Food Preservation Section, Joint FAO/ IAEA Division of Nuclear Techniques in Food and Agriculture, Wagramerstr. 5, A-1400, Vienna (Austria)

    1997-12-31

    There was a widely held opinion during the 1970`s and 1980`s that consumers would be reluctant to purchase irradiated food, as it was perceived that consumers would confuse irradiated food with food contaminated by radionuclides. Indeed, a number of consumer attitude surveys conducted in several western countries during these two decades demonstrated that the concerns of consumers on irradiated food varied from very concerned to seriously concerned.This paper attempts to review parameters conducting in measuring consumer acceptance of irradiated food during the past three decades and to project the trends on this subject. It is believed that important lessons learned from past studies will guide further efforts to market irradiated food with wide consumer acceptance in the future. (Author)

  1. Food irradiation receives international acceptance

    International Nuclear Information System (INIS)

    Beddoes, J.M.

    1982-01-01

    Irradition has advantages as a method of preserving food, especially in the Third World. The author tabulates some examples of actual use of food irradiation with dates and tonnages, and tells the story of the gradual acceptance of food irradiation by the World Health Organization, other international bodies, and the U.S. Food and Drug Administration (USFDA). At present, the joint IAEA/FAO/WHO standard permits an energy level of up to 5 MeV for gamma rays, well above the 1.3 MeV energy level of 60 Co. The USFDA permits irradiation of any food up to 10 krad, and minor constituents of a diet may be irradiated up to 5 Mrad. The final hurdle to be cleared, that of economic acceptance, depends on convincing the food processing industry that the process is technically and economically efficient

  2. Consumer acceptance of irradiated food

    International Nuclear Information System (INIS)

    Loaharanu, P.

    1997-01-01

    There was a widely held opinion during the 1970's and 1980's that consumers would be reluctant to purchase irradiated food, as it was perceived that consumers would confuse irradiated food with food contaminated by radionuclides. Indeed, a number of consumer attitude surveys conducted in several western countries during these two decades demonstrated that the concerns of consumers on irradiated food varied from very concerned to seriously concerned.This paper attempts to review parameters conducting in measuring consumer acceptance of irradiated food during the past three decades and to project the trends on this subject. It is believed that important lessons learned from past studies will guide further efforts to market irradiated food with wide consumer acceptance in the future. (Author)

  3. Risk acceptance by the population

    International Nuclear Information System (INIS)

    Diekershoff, K.

    1980-01-01

    Information which is given by systematical learning processes creates a necessary prerequisite for a partly realistic evaluation of risks. If the objective shall be achieved to reduce continuously the acceptance of risks it is absolutely necessary to include the persons concerned in the process of communication and formation. In this field social science could make a specific contribution by its approach in action research. (orig./RW) [de

  4. Public acceptance and public relations

    International Nuclear Information System (INIS)

    Tanaka, Yasumasa

    1977-01-01

    A set of problems are discussed, which must be studied before the public relations are dealt with. Firstly, the trade-off between energy and health must be considered. There were several ages in which the consideration on health took preference to the energy requirement in the past. For example, the use of coal in London was prohibited by the King's proclamation in 1,306. Secondly, the selection for the acceptance of atomic power development and utilization is based on the subjective susceptibility psychologically, and cannot be concluded only by the logical reasoning. Thirdly, the strict definition of ''national consensus'' is necessary. That is, whether does it mean pleviscite or mere mood. Fourthly, whether the atomic energy is free from the danger or death biologically or not. Fifthly, is there any method for discriminating the persons who accept atomic power from the persons who do not socially. Although the probability of death caused by atomic accidents is very small (one three hundred millionth a year), many peoples hate atomic power and oppose to the construction of nuclear power plants. Four reasons for this are considered: (1) social diffusion of innovation, (2) nuclear allergy, (3) shortage of the conception of risk-benefit, and (4) heterogeneity of the public. According to the investigation of the relationship between electric power and livelihood, carried out by the policy and science research institute in Tokyo, the highly subjective decision for the acceptance of atomic power is independent of the objective knowledge on atomic power. (Iwakiri, K.)

  5. Reportable Nuclide Criteria for ORNL Radioactive Waste Management Activities - 13005

    International Nuclear Information System (INIS)

    McDowell, Kip; Forrester, Tim; Saunders, Mark

    2013-01-01

    The U.S. Department of Energy's Oak Ridge National Laboratory (ORNL) in Oak Ridge, Tennessee generates numerous radioactive waste streams. Many of those streams contain a large number of radionuclides with an extremely broad range of concentrations. To feasibly manage the radionuclide information, ORNL developed reportable nuclide criteria to distinguish between those nuclides in a waste stream that require waste tracking versus those nuclides of such minimal activity that do not require tracking. The criteria include tracking thresholds drawn from ORNL onsite management requirements, transportation requirements, and relevant treatment and disposal facility acceptance criteria. As a management practice, ORNL maintains waste tracking on a nuclide in a specific waste stream if it exceeds any of the reportable nuclide criteria. Nuclides in a specific waste stream that screen out as non-reportable under all these criteria may be dropped from ORNL waste tracking. The benefit of these criteria is to ensure that nuclides in a waste stream with activities which meaningfully affect safety and compliance are tracked, while documenting the basis for removing certain isotopes from further consideration. (authors)

  6. Neutron absorber qualification and acceptance testing from the designer's perspective

    International Nuclear Information System (INIS)

    Bracey, W.; Chiocca, R.

    2004-01-01

    Starting in the mid 1990's, the USNRC began to require less than 100% credit for the 10B present in fixed neutron absorbers spent fuel transport packages. The current practice in the US is to use only 75% of the specified 10B in criticality safety calculations unless extensive acceptance testing demonstrates both the presence of the 10B and uniformity of its distribution. In practice, the NRC has accepted no more than 90% credit for 10B in recent years, while other national competent authorities continue to accept 100%. More recently, with the introduction of new neutron absorber materials, particularly aluminum / boron carbide metal matrix composites, the NRC has also expressed expectations for qualification testing, based in large part on Transnuclear's successful application to use a new composite material in the TN-68 storage / transport cask. The difficulty is that adding more boron than is really necessary to a metal has some negative effects on the material, reducing the ductility and the thermal conductivity, and increasing the cost. Excessive testing requirements can have the undesired effect of keeping superior materials out of spent fuel package designs, without a corresponding justification based on public safety. In European countries and especially in France, 100% credit has been accepted up to now with materials controls specified in the Safety Analysis Report (SAR): Manufacturing process approved by qualification testing Materials manufacturing controlled under a Quality Assurance system. During fabrication, acceptance testing directly on products or on representative samples. Acceptance criteria taking into account a statistical uncertainty corresponding to 3σ. The original and current bases for the reduced 10 B credit, the design requirements for neutron absorber materials, and the experience of Transnuclear and Cogema Logistics with neutron absorber testing are examined. Guidelines for qualification and acceptance testing and process controls

  7. [Revision of McDonald's new diagnostic criteria for multiple sclerosis].

    Science.gov (United States)

    Wiendl, H; Kieseier, B C; Gold, R; Hohlfeld, R; Bendszus, M; Hartung, H-P

    2006-10-01

    In 2001, an international panel suggested new diagnostic criteria for multiple sclerosis (MS). These criteria integrate clinical, imaging (MRI), and paraclinical results in order to facilitate diagnosis. Since then, these so-called McDonald criteria have been broadly accepted and widely propagated. In the meantime a number of publications have dealt with the sensitivity and specificity for MS diagnosis and with implementing these new criteria in clinical practice. Based on these empirical values and newer data on MS, an international expert group recently proposed a revision of the criteria. Substantial changes affect (1) MRI criteria for the dissemination of lesions over time, (2) the role of spinal cord lesions in the MRI and (3) diagnosis of primary progressive MS. In this article we present recent experiences with the McDonald and revised criteria.

  8. Wind power: basic challenge concerning social acceptance

    NARCIS (Netherlands)

    Wolsink, M.; Meyers, R.A.

    2012-01-01

    This reference article gives an overview of social acceptance (acceptance by all relevant actors in society) of all relevant aspects of implementation and diffusion of wind power. In social acceptance three dimensions of acceptance are distinguished (socio-political -; community -; market

  9. Dysplastic naevus: histological criteria and their inter-observer reproducibility.

    Science.gov (United States)

    Hastrup, N; Clemmensen, O J; Spaun, E; Søndergaard, K

    1994-06-01

    Forty melanocytic lesions were examined in a pilot study, which was followed by a final series of 100 consecutive melanocytic lesions, in order to evaluate the inter-observer reproducibility of the histological criteria proposed for the dysplastic naevus. The specimens were examined in a blind fashion by four observers. Analysis by kappa statistics showed poor reproducibility of nuclear features, while reproducibility of architectural features was acceptable, improving in the final series. Consequently, we cannot apply the combined criteria of cytological and architectural features with any confidence in the diagnosis of dysplastic naevus, and, until further studies have documented that architectural criteria alone will suffice in the diagnosis of dysplastic naevus, we, as pathologists, shall avoid this term.

  10. The role of natural analogues in safety assessment and acceptability

    International Nuclear Information System (INIS)

    Papp, Toenis

    1987-01-01

    The safety assessment must evaluate the level of safety for a repository, the confidence that can be placed on the assessment and how well the repository can meet the acceptance criteria of the society. Many of the processes and phenomena that govern the long term performance of a deep geologic repository for radioactive waste also take place in nature. To investigate these natural analogues and try to validate the models on which the safety assessment are based is a main task in the effort to build of confidence in the safety assessments. The assessment of the safety of a repository can, however, not only be based on good models. The possible role of natural analogues or natural evidence in other parts of the safety assessment is discussed. Specially with regard to - the need to demonstrate that all relevant processes have been taken into account, and that the important ones have been validated to an acceptable level for relevant parameters spans, -the definition and analysis of external scenarios for the safety assessment and for the claim that all reasonable scenarios have been addressed, - the public confidence in the long-term relevance of the acceptance criteria. (author)

  11. Social Advertising Quality: Assessment Criteria

    Directory of Open Access Journals (Sweden)

    S. B. Kalmykov

    2017-01-01

    Full Text Available Purpose: the The purpose of the publication is development of existing criterial assessment in social advertising sphere. The next objectives are provided for its achievement: to establish research methodology, to develop the author’s version of necessary notional apparatus and conceptual generalization, to determine the elements of social advertising quality, to establish the factors of its quality, to conduct the systematization of existing criteria and measuring instruments of quality assessment, to form new criteria of social advertising quality, to apply received results for development of criterial assessment to determine the further research perspectives. Methods: the methodology of research of management of social advertising interaction with target audience, which has dynamic procedural character with use of sociological knowledge multivariate paradigmatic status, has been proposed. Results: the primary received results: the multivariate paradigmatic research basis with use of works of famous domestic and foreign scientists in sociology, qualimetry and management spheres; the definitions of social advertising, its quality, sociological quality provision system, target audience behavior model during social advertising interaction are offered; the quality factors with three groups by level of effect on consumer are established; the systematization of existing quality and its measure instruments assessment criteria by detected social advertising quality elements are conducted; the two new criteria and its management quality assessment measuring instruments in social advertising sphere are developed; the one of the common groups of production quality criteria – adaptability with considering of new management quality criteria and conducted systematization of existing social advertising creative quality assessment criteria development; the perspective of further perfection of quality criterial assessment based on social advertising

  12. Qualification criteria to certify a package for air transport of plutonium

    International Nuclear Information System (INIS)

    1977-12-01

    The document describes qualification criteria developed by the U.S. Nuclear Regulatory Commission to certify a package for air transport of plutonium. Included in the document is a discussion of aircraft accident conditions and a summary of the technical basis for the qualification criteria. The criteria require prototype packages to be subjected to various individual and sequential tests that simulate the conditions produced in severe aircraft accidents. Specific post-test acceptance standards are prescribed for each of the three safety functions of a package. The qualification criteria also prescribe certain operational controls to be exercised during transport

  13. Criteria for saturated magnetization loop

    International Nuclear Information System (INIS)

    Harres, A.; Mikhov, M.; Skumryev, V.; Andrade, A.M.H. de; Schmidt, J.E.; Geshev, J.

    2016-01-01

    Proper estimation of magnetization curve parameters is vital in studying magnetic systems. In the present article, criteria for discrimination non-saturated (minor) from saturated (major) hysteresis loops are proposed. These employ the analysis of (i) derivatives of both ascending and descending branches of the loop, (ii) remanent magnetization curves, and (iii) thermomagnetic curves. Computational simulations are used in order to demonstrate their validity. Examples illustrating the applicability of these criteria to well-known real systems, namely Fe_3O_4 and Ni fine particles, are provided. We demonstrate that the anisotropy-field value estimated from a visual examination of an only apparently major hysteresis loop could be more than two times lower than the real one. - Highlights: • Proper estimation of hysteresis-loop parameters is vital in magnetic studies. • We propose criteria for discrimination minor from major hysteresis loops. • The criteria analyze magnetization, remanence and ZFC/FC curves and/or their derivatives. • Examples of their application on real nanoparticles systems are given. • Using the criteria could avoid twofold or bigger saturation-field underestimation errors.

  14. Criteria for saturated magnetization loop

    Energy Technology Data Exchange (ETDEWEB)

    Harres, A. [Departamento de Física, UFSM, Santa Maria, 97105-900 Rio Grande do Sul (Brazil); Mikhov, M. [Faculty of Physics, University of Sofia, 1164 Sofia (Bulgaria); Skumryev, V. [Institució Catalana de Recerca i Estudis Avançats, 08010 Barcelona (Spain); Departament de Física, Universitat Autònoma de Barcelona, 08193 Barcelona (Spain); Andrade, A.M.H. de; Schmidt, J.E. [Instituto de Física, UFRGS, Porto Alegre, 91501-970 Rio Grande do Sul (Brazil); Geshev, J., E-mail: julian@if.ufrgs.br [Departament de Física, Universitat Autònoma de Barcelona, 08193 Barcelona (Spain); Instituto de Física, UFRGS, Porto Alegre, 91501-970 Rio Grande do Sul (Brazil)

    2016-03-15

    Proper estimation of magnetization curve parameters is vital in studying magnetic systems. In the present article, criteria for discrimination non-saturated (minor) from saturated (major) hysteresis loops are proposed. These employ the analysis of (i) derivatives of both ascending and descending branches of the loop, (ii) remanent magnetization curves, and (iii) thermomagnetic curves. Computational simulations are used in order to demonstrate their validity. Examples illustrating the applicability of these criteria to well-known real systems, namely Fe{sub 3}O{sub 4} and Ni fine particles, are provided. We demonstrate that the anisotropy-field value estimated from a visual examination of an only apparently major hysteresis loop could be more than two times lower than the real one. - Highlights: • Proper estimation of hysteresis-loop parameters is vital in magnetic studies. • We propose criteria for discrimination minor from major hysteresis loops. • The criteria analyze magnetization, remanence and ZFC/FC curves and/or their derivatives. • Examples of their application on real nanoparticles systems are given. • Using the criteria could avoid twofold or bigger saturation-field underestimation errors.

  15. Fast Acceptance by Common Experience

    Directory of Open Access Journals (Sweden)

    Nathan Berg

    2010-08-01

    Full Text Available Schelling (1969, 1971a,b, 1978 observed that macro-level patterns do not necessarily reflect micro-level intentions, desires or goals. In his classic model on neighborhood segregation which initiated a large and influential literature, individuals with no desire to be segregated from those who belong to other social groups nevertheless wind up clustering with their own type. Most extensions of Schelling's model have replicated this result. There is an important mismatch, however, between theory and observation, which has received relatively little attention. Whereas Schelling-inspired models typically predict large degrees of segregation starting from virtually any initial condition, the empirical literature documents considerable heterogeneity in measured levels of segregation. This paper introduces a mechanism that can produce significantly higher levels of integration and, therefore, brings predicted distributions of segregation more in line with real-world observation. As in the classic Schelling model, agents in a simulated world want to stay or move to a new location depending on the proportion of neighbors they judge to be acceptable. In contrast to the classic model, agents' classifications of their neighbors as acceptable or not depend lexicographically on recognition first and group type (e.g., ethnic stereotyping second. The FACE-recognition model nests classic Schelling: When agents have no recognition memory, judgments about the acceptability of a prospective neighbor rely solely on his or her group type (as in the Schelling model. A very small amount of recognition memory, however, eventually leads to different classifications that, in turn, produce dramatic macro-level effects resulting in significantly higher levels of integration. A novel implication of the FACE-recognition model concerns the large potential impact of policy interventions that generate modest numbers of face-to-face encounters with members of other social groups.

  16. How acceptable has become tolerable

    International Nuclear Information System (INIS)

    Clarke, R.H.

    1989-01-01

    A brief article discusses the differing conclusions drawn by the Royal Society Study Group and the Health and Safety Executive on the acceptability of the level of annual risk of death to the individual due to radiation. Regarding occupational exposure, both groups arrived at the same figure of 1 in 1000 per year but the former group considered this to be 'hardly totally unacceptable' while the latter group considered this to be 'borderline of intolerable'. Regarding exposure of the members of the public, the levels of risk concluded from both groups were even more divergent. (U.K.)

  17. Axelrod model: accepting or discussing

    Science.gov (United States)

    Dybiec, Bartlomiej; Mitarai, Namiko; Sneppen, Kim

    2012-10-01

    Agents building social systems are characterized by complex states, and interactions among individuals can align their opinions. The Axelrod model describes how local interactions can result in emergence of cultural domains. We propose two variants of the Axelrod model where local consensus is reached either by listening and accepting one of neighbors' opinion or two agents discuss their opinion and achieve an agreement with mixed opinions. We show that the local agreement rule affects the character of the transition between the single culture and the multiculture regimes.

  18. Acceptable Knowledge Summary Report for Waste Stream: SR-T001-221F-HET/Drums

    International Nuclear Information System (INIS)

    Lunsford, G.F.

    1999-01-01

    This report is fully responsive to the requirements of Section 4.0 ''Acceptable Knowledge'' from the WIPP Transuranic Waste Characterization Quality Assurance Plan, CAO-94-1010, and provides a sound, (and auditable) characterization that satisfies the WIPP criteria for Acceptable Knowledge

  19. User perspectives on relevance criteria

    DEFF Research Database (Denmark)

    Maglaughlin, Kelly L.; Sonnenwald, Diane H.

    2002-01-01

    , partially relevant, or not relevant to their information need; and explained their decisions in an interview. Analysis revealed 29 criteria, discussed positively and negatively, that were used by the participants when selecting passages that contributed or detracted from a document's relevance......This study investigates the use of criteria to assess relevant, partially relevant, and not-relevant documents. Study participants identified passages within 20 document representations that they used to make relevance judgments; judged each document representation as a whole to be relevant...... matter, thought catalyst), full text (e.g., audience, novelty, type, possible content, utility), journal/publisher (e.g., novelty, main focus, perceived quality), and personal (e.g., competition, time requirements). Results further indicate that multiple criteria are used when making relevant, partially...

  20. Criteria for authorship in bioethics.

    Science.gov (United States)

    Resnik, David B; Master, Zubin

    2011-10-01

    Multiple authorship is becoming increasingly common in bioethics research. There are well-established criteria for authorship in empirical bioethics research but not for conceptual research. It is important to develop criteria for authorship in conceptual publications to prevent undeserved authorship and uphold standards of fairness and accountability. This article explores the issue of multiple authorship in bioethics and develops criteria for determining who should be an author on a conceptual publication in bioethics. Authorship in conceptual research should be based on contributing substantially to: (1) identifying a topic, problem, or issue to study; (2) reviewing and interpreting the relevant literature; (3) formulating, analyzing, and evaluating arguments that support one or more theses; (4) responding to objections and counterarguments; and (5) drafting the manuscript. Authors of conceptual publications should participate substantially in at least two of areas (1)-(5) and also approve the final version. [corrected].

  1. An evaluation and acceptance of COTS software for FPGA-based controllers in NPPS

    International Nuclear Information System (INIS)

    Jung, Sejin; Kim, Eui-Sub; Yoo, Junbeom; Kim, Jang-Yeol; Choi, Jong Gyun

    2016-01-01

    Highlights: • All direct/indirect COTS SW should be dedicated. • FPGA synthesis tools are important for the safety of new digital I&Cs. • No standards/reports are yet available to deal with the indirect SW – FPGA synthesis tools. • This paper proposes a new evaluation/acceptance process and criteria for indirect SW. - Abstract: FPGA (Field-Programmable Gate Array) has received much attention from nuclear industry as an alternative platform of PLC (Programmable Logic Controller)-based digital I&C (Instrumentation & Control). Software aspect of FPGA development encompasses several commercial tools such as logic synthesis and P&R (Place & Route), which should be first dedicated in accordance with domestic standards based on EPRI NP-5652. Even if a state-of-the-art supplementary EPRI TR-1025243 makes an effort, the dedication of indirect COTS (Commercial Off-The-Shelf) SW such as FPGA logic synthesis tools has still caused a dispute. This paper proposes an acceptance process and evaluation criteria, specific to COTS SW, not commercial-grade direct items. It specifically incorporates indirect COTS SW and also provides categorized evaluation criteria for acceptance. It provides an explicit linkage between acceptance methods (Verification and Validation techniques) and evaluation criteria, too. We tried to perform the evaluation and acceptance process upon a commercial FPGA logic synthesis tool being used to develop a new FPGA-based digital I&C in Korea, and could confirm its applicability.

  2. A Systematic Review of Patient Acceptance of Consumer Health Information Technology

    OpenAIRE

    Karsh, BT; Or, CKL

    2009-01-01

    A systematic literature review was performed to identify variables promoting consumer health information technology (CHIT) acceptance among patients. The electronic bibliographic databases Web of Science, Business Source Elite, CINAHL, Communication and Mass Media Complete, MEDLINE, PsycArticles, and PsycInfo were searched. A cited reference search of articles meeting the inclusion criteria was also conducted to reduce misses. Fifty-two articles met the selection criteria. Among them, 94 diff...

  3. Design criteria for advanced reactors

    International Nuclear Information System (INIS)

    Dennielou, Y.

    1991-01-01

    Design criteria for advanced reactors are discussed, including safety aspects, site selection, problems related to maintenance and possibility of repairing or replacing structures or components of a nuclear power plant, the human factor considerations. Bearing in mind that some of these criteria are the subject of consensus at international level, the author suggests to establish a table of different operator requirements, to prepare a dossier on the comparison of input data for probabilistic risk analysis, to take into consideration the means to control a severe accident from the very start of the design

  4. FUZZY ACCEPTANCE SAMPLING AND CHARACTERISTIC CURVES

    Directory of Open Access Journals (Sweden)

    Ebru Turano?lu

    2012-02-01

    Full Text Available Acceptance sampling is primarily used for the inspection of incoming or outgoing lots. Acceptance sampling refers to the application of specific sampling plans to a designated lot or sequence of lots. The parameters of acceptance sampling plans are sample sizes and acceptance numbers. In some cases, it may not be possible to define acceptance sampling parameters as crisp values. These parameters can be expressed by linguistic variables. The fuzzy set theory can be successfully used to cope with the vagueness in these linguistic expressions for acceptance sampling. In this paper, the main distributions of acceptance sampling plans are handled with fuzzy parameters and their acceptance probability functions are derived. Then the characteristic curves of acceptance sampling are examined under fuzziness. Illustrative examples are given.

  5. Public acceptance: A Japanese view

    International Nuclear Information System (INIS)

    1972-01-01

    A number of factors enter into a consideration of the public acceptance of nuclear power ? the public, nuclear power as an entity, and the interaction between the two. Interaction here implies the manner in which nuclear power is presented to the public ? what is the public need for nuclear power, and what public risk is entailed in having it? The problem of public acceptance, in this sense, is time-dependent. For the public is changeable, just as nuclear power is subject to technical progress and ' social' improvement. Japan is geographically a very small country with a very high density of population. Any industrial activity and any large-scale employment of modern technology is apt to have a much greater impact on the physical, social and biological environment of individual Japanese people than similar activities would have on those of other countries. Industrial pollutants such as sulphur dioxide from power plants, oxides of nitrogen from automobile engine exhausts, organic mercury from chemical industries and so on affect society to a high degree, considered in terms of their concentration either per capita or per square kilometre. In the case of nuclear power, therefore, people are more concerned with radiological effects than with thermal pollution.no matter how one looks at it, the experience of Hiroshima and Nagasaki has made the average member of the Japanese public, very sensitive to the problem of radiation safety. This is no longer a subject in which science or logic can persuade

  6. Public acceptance: A Japanese view

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1972-07-01

    A number of factors enter into a consideration of the public acceptance of nuclear power ? the public, nuclear power as an entity, and the interaction between the two. Interaction here implies the manner in which nuclear power is presented to the public ? what is the public need for nuclear power, and what public risk is entailed in having it? The problem of public acceptance, in this sense, is time-dependent. For the public is changeable, just as nuclear power is subject to technical progress and ' social' improvement. Japan is geographically a very small country with a very high density of population. Any industrial activity and any large-scale employment of modern technology is apt to have a much greater impact on the physical, social and biological environment of individual Japanese people than similar activities would have on those of other countries. Industrial pollutants such as sulphur dioxide from power plants, oxides of nitrogen from automobile engine exhausts, organic mercury from chemical industries and so on affect society to a high degree, considered in terms of their concentration either per capita or per square kilometre. In the case of nuclear power, therefore, people are more concerned with radiological effects than with thermal pollution.no matter how one looks at it, the experience of Hiroshima and Nagasaki has made the average member of the Japanese public, very sensitive to the problem of radiation safety. This is no longer a subject in which science or logic can persuade.

  7. Waste transmutation and public acceptance

    International Nuclear Information System (INIS)

    Pigford, T.H.

    1991-01-01

    The concept of transmuting radioactive wastes with reactors or accelerators is appealing. It has the potential of simplifying or eliminating problems of disposing of nuclear waste. The transmutation concept has been renewed vigorously at a time when national projects to dispose of high-level and transuranic waste are seriously delayed. In this period of tightening federal funds and program curtailments, skilled technical staffs are available at US Department of Energy (DOE) national laboratories and contractors to work on waste transmutation. If the claims of transmutation can be shown to be realistic, economically feasible, and capable of being implemented within the US institutional infrastructure, public acceptance of nuclear waste disposal may be enhanced. If the claims for transmutation are not substantiated, however, there will result a serious loss of credibility and an unjust exacerbation of public concerns about nuclear waste. The paper discusses the following topics: how public acceptance is achieved; the technical community and waste disposal; transmutation and technical communication; transmutation issues; technical fixes and public perception

  8. Wind energy and social acceptability

    International Nuclear Information System (INIS)

    Feurtey, E.

    2008-01-01

    This document was prepared as part of a decentralized collaboration between Quebec and France to share knowledge regarding strategies and best practices in wind power development. It reviewed the social acceptance of Quebec's wind power industry, particularly at the municipal level. The wind industry is growing rapidly in Quebec, and this growth has generated many reactions ranging from positive to negative. The purpose of this joint effort was to describe decision making steps to developing a wind turbine array. The history of wind development in Quebec was discussed along with the various hardware components required in a wind turbine and different types of installations. The key element in implementing wind turbine arrays is to establish public acceptance of the project, followed by a good regulatory framework to define the roles and responsibilities of participants. The production of electricity from wind turbines constitutes a clean and renewable source of energy. Although it is associated with a reduction in greenhouse gas emissions, this form of energy can also have negative environmental impacts, including noise. The revenues generated by wind parks are important factors in the decision making process. Two case studies in Quebec were presented. refs., tabs., figs.

  9. Policy formulation of public acceptance

    International Nuclear Information System (INIS)

    Kasai, Akihiro

    1978-01-01

    Since 1970, the new policy formulation for public acceptance of the new consideration on the location of electric power generation has been set and applied. The planning and the enforcement being conducted by local public organizations for the local economic build-up with plant location and also the adjustement of the requirements for fishery are two main specific characters in this new policy. The background of this new public acceptance policy, the history and the actual problems about the compensation for the location of power generation plants are reviewed. One new proposal, being recommended by the Policy and Science Laboratory to MITI in 1977 is explained. This is based on the method of promoting the location of power generation plants by public participation placing the redevelopment of regional societies as its basis. The problems concerning the industrial structures in farm villages, fishing villages and the areas of commerce and industry should be systematized, and explained from the viewpoint of outside impact, the characteristics of local areas and the location problems in this new proposal. Finally, the location process and its effectiveness should be put in order. (Nakai, Y.)

  10. OSCILLATION CRITERIA FOR FORCED SUPERLINEAR DIFFERENCE EQUATIONS

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Using Riccati transformation techniques,some oscillation criteria for the forced second-order superlinear difference equations are established.These criteria are dis- crete analogues of the criteria for differential equations proposed by Yan.

  11. US Department of Energy acceptance of commercial transuranic waste

    International Nuclear Information System (INIS)

    Taboas, A.L.; Bennett, W.S.; Brown, C.M.

    1980-02-01

    Contaminated transuranic wastes generated as a result of non-defense activities have been disposed of by shallow land burial at a commercially operated (NECO) facility located on the Hanford federal reservation, which is licensed by the State of Washington and by the NRC. About 15,000 ft 3 of commercial TRU waste have been generated each year, but generation for the next three years could triple due to decontamination and decommissioning scheduled to start in 1980. Disposal at other commercial burial sites has been precluded due to sites closing or prohibitions on acceptance of transuranic wastes. The State of Washington recently modified the NECO-Hanford operating license, effective February 29, 1980, to provide that radioactive wastes contaminated with transuranics in excess of 10 nCi/g will not be accepted for disposal. Consistent with the state policy, the NRC amended the NECO special nuclear material license so that Pu in excess of 10n Ci/g cannot be accepted after February 29, 1980. As a result, NRC requested DOE to examine the feasibility of accepting these wastes at a DOE operated site. TRU wastes accepted by the DOE would be placed in retrievable storage in accordance with DOE policy which requires retrievable storage of transuranic wastes pending final disposition in a geologic repository. DOE transuranic wastes are stored at six major DOE sites: INEL, Hanford, LASL, NTS, ORNL, and SRP. A specific site for receiving commercial TRU waste has not yet been selected. Shipments to DOE-Hanford would cause the least disruption to past practices. Commercial TRU wastes would be subject to waste form and packaging criteria established by the DOE. The waste generators would be expected to incur all applicable costs for DOE to take ownership of the waste, and provide storage, processing, and repository disposal. The 1980 charge to generators for DOE acceptance of commercial TRU waste is $147 per cubic foot

  12. 105 K East isolation barrier acceptance analysis report

    International Nuclear Information System (INIS)

    McCracken, K.J.; Irwin, J.J.

    1995-01-01

    The objective of this document is to report and interpret the findings of the isolation barrier acceptance tests performed in 105KE/100K. The tests were performed in accordance with the test plan (McCracken 1995c) and acceptance test procedure (McCracken 1995a). The test report (McCracken 1995b) contains the test data. This document compares the test data (McCracken 1995b) against the criteria (McCracken 1995a, c). A discussion of the leak rate analytical characterization (Irwin 1995) describes how the flow characteristics and the flow rate will be determined using the test data from the test report (McCracken 1995b). The barriers must adequately control the leakage from the main basin to the discharge chute to less than the 1,500 gph (5,680 lph) Safety Analysis Report (SAR 1994) limit

  13. Acceptance test report for portable exhauster POR-007/Skid E

    International Nuclear Information System (INIS)

    Kriskovich, J.R.

    1998-01-01

    This document describes Acceptance Testing performed on Portable Exhauster POR-007/Skid E. It includes measurements of bearing vibration levels, pressure decay testing, programmable logic controller interlocks, high vacuum, flow and pressure control functional testing. The purpose of Acceptance testing documented by this report was to demonstrate compliance of the exhausters with the performance criteria established within HNF-0490, Rev. 1 following a repair and upgrade effort at Hanford. In addition, data obtained during this testing is required for the resolution of outstanding Non-conformance Reports (NCR), and finally, to demonstrate the functionality of the associated software for the pressure control and high vacuum exhauster operating modes provided for by W-320. Additional testing not required by the ATP was also performed to assist in the disposition and close out of receiving inspection report and for application design information (system curve). Results of this testing are also captured within this document

  14. Preparing to Accept Research Data: Creating Guidelines for Librarians

    Directory of Open Access Journals (Sweden)

    Laura B. Palumbo

    2015-11-01

    Full Text Available Rutgers University Libraries have recognized the need to expand their current research data services into a well-documented and well-supported service available to the Rutgers research community. In 2005, Rutgers University Libraries created RUcore, Rutgers University Community Repository, which has served as the University’s formal repository for institutional scholarship, special collections, and Electronic Theses & Dissertations. With the impetus of the 2010 NSF directive for research data sharing and preservation, RUcore development was extended to accept research data content. Ingest of pilot data projects began in 2010 via a librarian-mediated process. In order to provide a better defined workflow and mission for research data services, in July 2014, the Rutgers University Librarian organized a Task Force to investigate the evaluation process for technical, legal, and confidential issues involved in research data acceptance, and to establish an administrative and evaluation framework for the deposit of research data. After a review of 35 repositories using 34 criteria, the Task Force drafted a plan for research data acceptance which proposes wide-spread acceptance of mediated data projects, and prepares for future self-deposit in an online interface. This paper will discuss the issues addressed by the Task Force; acknowledging ownership of data through an institutional data policy, preventing exposure of confidential or sensitive data, establishing a reconfigured data team, requirements for storage capacity and funding, creating a workflow which includes collaboration with research offices, and offering guidance for both researchers and librarians working with research data.

  15. Accident analysis and DOE criteria

    International Nuclear Information System (INIS)

    Graf, J.M.; Elder, J.C.

    1982-01-01

    In analyzing the radiological consequences of major accidents at DOE facilities one finds that many facilities fall so far below the limits of DOE Order 6430 that compliance is easily demonstrated by simple analysis. For those cases where the amount of radioactive material and the dispersive energy available are enough for accident consequences to approach the limits, the models and assumptions used become critical. In some cases the models themselves are the difference between meeting the criteria or not meeting them. Further, in one case, we found that not only did the selection of models determine compliance but the selection of applicable criteria from different chapters of Order 6430 also made the difference. DOE has recognized the problem of different criteria in different chapters applying to one facility, and has proceeded to make changes for the sake of consistency. We have proposed to outline the specific steps needed in an accident analysis and suggest appropriate models, parameters, and assumptions. As a result we feed DOE siting and design criteria will be more fairly and consistently applied

  16. Aversive Stimulation -- Criteria for Application.

    Science.gov (United States)

    O'Donnell, Patrick A.; Ohlson, Glenn A.

    Criteria for applying aversive stimulation with severely handicapped children are examined, and practical and ethical issues are considered. Factors seen to influence punishment outcomes include timing, intensity, and schedule of reinforcement. Suggested is the need for further research on the comparative effectiveness of positive and negative…

  17. Evaluation criteria for dialogue processes: key findings from RISCOM II

    International Nuclear Information System (INIS)

    Atherton, Elizabeth

    2003-01-01

    As part of Work Package 4 (undertaken by a consortium of partners from the United Kingdom) in the joint European project RISCOM II, work was undertaken on evaluation criteria for determining the success of dialogue processes; this note outlines its key findings as, in order to continue the development of dialogue processes, it is important to evaluate and learn from the experience of engaging with stakeholders. Criteria can be developed to evaluate how successful a process has been, these can range from very practical criteria relating to how well the process worked or be linked to more subjective criteria developed from the aims of the dialogue process itself. Some criteria are particularly relevant to dialogue processes that aim to encourage deliberation and the development of stakeholders' views through participation in the dialogue process: transparency, legitimacy, equality of access, 'being able to speak', a deliberative environment, openness of framing, developing insight into range of issues (new meanings are generated), inclusive and 'best' knowledge elicited, producing acceptable/tolerable and usable outcomes/decisions, improvement of trust and understanding between participants, developing a sense of shared responsibility and common good. Evaluation will incur a cost in terms of time and money, but will help practitioners to be able to develop processes that meet the needs of those who participate and improve the way that we try to engage people in the debate

  18. Seismic design and evaluation criteria based on target performance goals

    International Nuclear Information System (INIS)

    Murray, R.C.; Nelson, T.A.; Kennedy, R.P.; Short, S.A.

    1994-04-01

    The Department of Energy utilizes deterministic seismic design/evaluation criteria developed to achieve probabilistic performance goals. These seismic design and evaluation criteria are intended to apply equally to the design of new facilities and to the evaluation of existing facilities. In addition, the criteria are intended to cover design and evaluation of buildings, equipment, piping, and other structures. Four separate sets of seismic design/evaluation criteria have been presented each with a different performance goal. In all these criteria, earthquake loading is selected from seismic hazard curves on a probabilistic basis but seismic response evaluation methods and acceptable behavior limits are deterministic approaches with which design engineers are familiar. For analytical evaluations, conservatism has been introduced through the use of conservative inelastic demand-capacity ratios combined with ductile detailing requirements, through the use of minimum specified material strengths and conservative code capacity equations, and through the use of a seismic scale factor. For evaluation by testing or by experience data, conservatism has been introduced through the use of an increase scale factor which is applied to the prescribed design/evaluation input motion

  19. Screening Criteria and Considerations of Offshore Enhanced Oil Recovery

    Directory of Open Access Journals (Sweden)

    Pan-Sang Kang

    2016-01-01

    Full Text Available The application of enhanced oil recovery (EOR in offshore oil fields has received significant attention due to the potentially enormous amount of recoverable oil. However, EOR application offshore is in its very early stage due to conditions that are more complex than onshore oil fields, owing to the unique parameters present offshore. Therefore, successful EOR applications in offshore oil fields require different screening criteria than those for conventional onshore applications. A comprehensive database for onshore applications of EOR processes together with a limited offshore EOR application database are analyzed in this paper, and the important parameters for successful offshore application are incorporated into the new EOR screening criteria. In this paper, screening criteria to determine acceptable EOR processes for offshore fields, including hydrocarbon gas miscible, CO2 miscible, and polymer processes, are presented. Suggested screening criteria for these EOR processes comprise quantitative boundaries and qualitative considerations. Quantitative screening criteria are predominantly based on quantifiable data, such as oil and reservoir properties. Qualitative screening considerations mainly focus on the operational issues present offshore, including platform space constraints, limited disposal options, injectant availability, and flow assurance matters (including hydrate formation and difficulties in emulsion separation.

  20. PAGs - Public perception and acceptance

    International Nuclear Information System (INIS)

    Quillin, Robert M.

    1989-01-01

    Full text: While Protective Action Guides or PAGs have been a part of the lexicon of the radiation protection field for several decades, the concept of accepting higher levels of risk under certain situations has not received adequate scrutiny by the general public, the media or elected officials. Consequently there is a question as to how implementation of PAGs would be perceived by the above groups in the event that such implementation became necessary. A personal case in point involves the response of an executive in the food industry. When the concept of selling a food product meeting the PAGs was explained his response was, 'we won't sell a contaminated product, we would dump the unprocessed raw food. Our industry image is that of a natural unadulterated food'. While this may be an isolated view, there is a need to determine what is the perception and consequently what would be the response if PAGs were implemented today. If the response was negative by anyone of the three groups listed previously, then there is an obvious need for a program to assure receptiveness by those concerned. However, this may face formidable obstacles. This is because the terms radiation and radioactive have gained generally negative word associations, e.g. 'deadly' radiation and radioactive 'desert'. The former term was recently heard in a taped presentation at a Museum of Natural History on a completely unrelated subject. The latter term was part of a recent article heading in the Wall Street Journal. Incidentally the article was discussing television. Thus beyond the scientific issues of setting PAGs and the administrative and procedural issues of implementing PAGs there is the issue of society's understanding and acceptance of PAGs. Particularly, how can such understanding and acceptance be achieved in a situation which is associated with an actual or perceived radiation emergency? These are not questions that radiation or agricultural scientists can answer alone. These are

  1. PUBLIC ACCEPTANCE OF ROAD-USER CHARGING

    Directory of Open Access Journals (Sweden)

    Neil THORPE

    2002-01-01

    Full Text Available This paper focuses upon public attitudes to and public acceptance of road-user charging as an effective means of managing travel demand, with the overall aim of identifying the characteristics of key interest groups, the kinds of attitudes they hold and their preferences for the distribution of the benefits of generated net revenues and released roadspace. It is argued that this knowledge can play a pivotal role in the design of road-user charging systems that satisfy two important criteria – namely, that they are capable of achieving their stated objectives and are generally acceptable to the public. A case-study of three toll-rings used for revenue generation by the Norwegian cities of Bergen, Oslo and Trondheim is selected, where a team of Norwegian interviewers administered a computer-based survey to a total of 756 respondents. Results of the analyses of the attitudinal data collected raise concerns about the approach of introducing initially low levels of road-use charge, designed to have negligible impacts on travel behaviour but to raise revenues to fund necessary improvements to public transport, both to familiarise private car-users with the principles of a pay-as-you-go system of charging and hopefully to reduce levels of public opposition prior to the introduction of the longer term objective of higher charges for traffic restraint. The timescale over which charges are increased may be crucial in terms of balancing a resistance to change in the longer term against the credibility of a system whose objectives are modified in the relatively short-term. The key conclusion from the first Stated Preference exercise is that there is a high degree of consensus among individuals on the importance of investing significant amounts of net revenues in new road infrastructure as well as improved public transport. The second Stated Preference exercise highlights respondents' concerns that the benefits in improved network performance achieved by a

  2. Acceptance of Others, Feeling of Being Accepted and Striving for Being Accepted Among the Representatives of Different Kinds of Occupations

    Directory of Open Access Journals (Sweden)

    Gergana Stanoeva

    2012-05-01

    Full Text Available This paper deals with an important issue related to the human attitudes and needs in interpersonal and professional aspects. The theoretical part deals with several psychological components of the self-esteem and esteem of the others – acceptance of the others, feeling of being accepted, need for approval. Some gender differences in manifestations of acceptance and feeling of being accepted at the workplace are discussed. This article presents some empirical data for the degree of acceptance of others, feeling of being accepted and the strive for being accepted among the representatives of helping, pedagogical, administrative and economic occupations, as well as non-qualified workers. The goals of the study were to reveal the interdependency between these constructs and to be found some significant differences between the representatives of the four groups of occupations. The methods of the first study were W. Fey’s scales “Acceptance of others”, and “How do I feel accepted by others”. The method of the second study was Crown and Marlowe Scale for Social Desirability. The results indicated some significant differences in acceptance of others and feeling of being accepted between the non-qualified workers and the representatives of helping, administrative and economic occupations. There were not any significant difference in strive for being accepted between the fouroccupational groups.

  3. Evaluating Dependence Criteria for Caffeine.

    Science.gov (United States)

    Striley, Catherine L W; Griffiths, Roland R; Cottler, Linda B

    2011-12-01

    Background: Although caffeine is the most widely used mood-altering drug in the world, few studies have operationalized and characterized Diagnostic and Statistical Manual IV (DSM-IV) substance dependence criteria applied to caffeine. Methods: As a part of a nosological study of substance use disorders funded by the National Institute on Drug Abuse, we assessed caffeine use and dependence symptoms among high school and college students, drug treatment patients, and pain clinic patients who reported caffeine use in the last 7 days and also reported use of alcohol, nicotine, or illicit drugs within the past year ( n =167). Results: Thirty-five percent met the criteria for dependence when all seven of the adopted DSM dependence criteria were used. Rates of endorsement of several of the most applicable diagnostic criteria were as follows: 26% withdrawal, 23% desire to cut down or control use, and 44% continued use despite harm. In addition, 34% endorsed craving, 26% said they needed caffeine to function, and 10% indicated that they talked to a physician or counselor about problems experienced with caffeine. There was a trend towards increased caffeine dependence among those dependent on nicotine or alcohol. Within a subgroup that had used caffeine, alcohol, and nicotine in the past year, 28% fulfilled criteria for caffeine dependence compared to 50% for alcohol and 80% for nicotine. Conclusion: The present study adds to a growing literature suggesting the reliability, validity, and clinical utility of the caffeine dependence diagnosis. Recognition of caffeine dependence in the DSM-V may be clinically useful.

  4. User acceptance of mobile notifications

    CERN Document Server

    Westermann, Tilo

    2017-01-01

    This book presents an alternative approach to studying smartphone-app user notifications. It starts with insights into user acceptance of mobile notifications in order to provide tools to support users in managing these. It extends previous research by investigating factors that influence users’ perception of notifications and proposes tools addressing the shortcomings of current systems. It presents a technical framework and testbed as an approach for evaluating the usage of mobile applications and notifications, and then discusses a series of studies based on this framework that investigate factors influencing users’ perceptions of mobile notifications. Lastly, a set of design guidelines for the usage of mobile notifications is derived that can be employed to support users in handling notifications on smartphones.

  5. Preliminary estimates of the impacts of alternative spent fuel acceptance rates

    International Nuclear Information System (INIS)

    Clark, L.L.; McKee, R.W.; Short, S.M.

    1986-02-01

    The rate at which spent fuel is accepted by the federal waste management system is an important interface between the private nuclear power sector and the federal government, which will assume responsibility for spent fuel disposal. An analysis of alternative rates based on minimum age criteria indicates substantial incentives to limit acceptance rates so as to result in minimum 10 to 15 year fuel ages for repository acceptance [1500 to 2500 metric tons of uranium (MTU) per year]. These incentives include lower heat generation rates and systems costs

  6. Waste acceptance product specifications for vitrified high-level waste forms

    International Nuclear Information System (INIS)

    Applewhite-Ramsey, A.; Sproull, J.F.

    1994-01-01

    The Department of Energy (DOE) Office of Environmental Restoration and Waste Management (EM) has developed Waste Acceptance Product Specifications (EM-WAPS). The EM-WAPS will be the basis for defining product acceptance criteria compatible with the requirements of the Civilian Radioactive Waste Management System (CRWMS). The relationship between the EM-WAPS and the CRWMS Systems Requirements document (WA-SRD) will be discussed. The impact of the EM-WAPS on the Savannah River Sit (SRS) Defense Waste Processing Facility's (DWPF) Waste Acceptance Program, Waste Qualification Run planning, and startup schedule will also be reported. 14 refs., 2 tabs

  7. A proposed acceptance process for commercial off-the-shelf (COTS) software in reactor applications

    International Nuclear Information System (INIS)

    Preckshot, G.G.; Scott, J.A.

    1996-03-01

    This paper proposes a process for acceptance of commercial off-the-shelf (COTS) software products for use in reactor systems important to safety. An initial set of four criteria establishes COTS software product identification and its safety category. Based on safety category, three sets of additional criteria, graded in rigor, are applied to approve/disapprove the product. These criteria fall roughly into three areas: product assurance, verification of safety function and safety impact, and examination of usage experience of the COTS product in circumstances similar to the proposed application. A report addressing the testing of existing software is included as an appendix

  8. Antecedents to Consumers' Acceptance of Mobile Advertisements

    DEFF Research Database (Denmark)

    Rajala, Risto; Westerlund, Mika

    2010-01-01

    The paper presents a hierarchical construct PLS structural equation model to analyze mobile advertisement acceptance. Hypotheses are established and tested about the hierarchical structure and the effects of the factors that precede consumers' behavioral intention to accept mobile advertisement....... The results suggest that valuable content and trust in advertisers are key predictors of mobile device users' acceptance of mobile advertising. In addition, subjective value of the ads and subjective norms mediate these antecedent-acceptance relationships. The results are invaluable to both scholars...

  9. 40 CFR 80.584 - What are the precision and accuracy criteria for approval of test methods for determining the...

    Science.gov (United States)

    2010-07-01

    ... criteria for approval of test methods for determining the sulfur content of motor vehicle diesel fuel, NRLM....584 What are the precision and accuracy criteria for approval of test methods for determining the... available gravimetric sulfur standard in the range of 1-10 ppm sulfur shall not differ from the accepted...

  10. Criteria for permission of radiosterilized products to application in medicine; Zasady dopuszczania wyrobow sterylizowanych radiacyjnie do stosowania w medycynie

    Energy Technology Data Exchange (ETDEWEB)

    Achmatowicz, T [Instytut Lekow, Warsaw (Poland)

    1997-10-01

    The criteria being used in Poland for permission of radiosterilized medical materials to commercial application result from regulations being in force. The international regulations are also taken into account. The all criteria and procedure needed for any product become accepted for radiosterilization and commercial medical use have been presented and discussed. 1 tab.

  11. 46 CFR 28.73 - Accepted organizations.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 1 2010-10-01 2010-10-01 false Accepted organizations. 28.73 Section 28.73 Shipping... INDUSTRY VESSELS General Provisions § 28.73 Accepted organizations. An organization desiring to be designated by the Commandant as an accepted organization must request such designation in writing. As a...

  12. Older Adults' Acceptance of Information Technology

    Science.gov (United States)

    Wang, Lin; Rau, Pei-Luen Patrick; Salvendy, Gavriel

    2011-01-01

    This study investigated variables contributing to older adults' information technology acceptance through a survey, which was used to find factors explaining and predicting older adults' information technology acceptance behaviors. Four factors, including needs satisfaction, perceived usability, support availability, and public acceptance, were…

  13. Relevant cost information for order acceptance decisions

    NARCIS (Netherlands)

    Wouters, M.J.F.

    1997-01-01

    Some economic considerations for order acceptance decisions are discussed. The relevant economic considerations for order acceptance are widely discussed in the literature: only those costs are relevant which would be avoidable by not accepting the order incremental costs plus opportunity costs .

  14. Credit in Acceptance Sampling on Attributes

    NARCIS (Netherlands)

    Klaassen, Chris A.J.

    2000-01-01

    Credit is introduced in acceptance sampling on attributes and a Credit Based Acceptance sampling system is developed that is very easy to apply in practice.The credit of a producer is defined as the total number of items accepted since the last rejection.In our sampling system the sample size for a

  15. Early Site Permit Demonstration Program: Regulatory criteria evaluation report

    International Nuclear Information System (INIS)

    1993-03-01

    The primary objective of the ESPDP is to demonstrate successfully the use of 10CFR52 to obtain ESPs for one or more US sites for one (or more) ALWR nuclear power plants. It is anticipated that preparation of the ESP application and interaction with NRC during the application review process will result not only in an ESP for the applicant(s) but also in the development of criteria and definition of processes, setting the precedent that facilitates ESPs for subsequent ESP applications. Because siting regulatory processes and acceptance criteria are contained in over 100 separate documents, comprehensive licensing and technical reviews were performed to establish whether the requirements and documentation are self-consistent, whether the acceptance criteria are sufficiently well-defined and clear, and whether the licensing process leading to the issuance of an ESP is unambiguously specified. The results of the technical and licensing evaluations are presented in this report. The purpose, background, and organization of the ESPDP is delineated in Section 1. Section 11 contains flowcharts defining siting application requirements, environmental report requirements, and emergency planning/preparedness requirements for ALWRS. The licensing and technical review results are presented in Section III

  16. Early Site Permit Demonstration Program: Regulatory criteria evaluation report

    International Nuclear Information System (INIS)

    1993-03-01

    The primary objective of the Early Site Plan Demonstration Program (ESPDP) is to demonstrate successfully the use of 10CFR52 to obtain ESPs for one or more US sites for one (or more) ALWR nuclear power plants. It is anticipated that preparation of the ESP application and interaction with NRC during the application review process will result not only in an ESP for the applicant(s) but also in the development of criteria and definition of processes, setting the precedent that facilitates ESPs for subsequent ESP applications. Because siting regulatory processes and acceptance criteria are contained in over 100 separate documents, comprehensive licensing and technical reviews were performed to establish whether the requirements and documentation are self-consistent, whether the acceptance criteria are sufficiently well-defined and clear, and whether the licensing process leading to the issuance of an ESP is unambiguously specified. This document provides appendices C and D of this report. Appendix C contains data from the licensing and technical reviews; Appendix D contains technology toolkit data sheets

  17. Early Site Permit Demonstration Program: Regulatory criteria evaluation report

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    The primary objective of the ESPDP is to demonstrate successfully the use of 10CFR52 to obtain ESPs for one or more US sites for one (or more) ALWR nuclear power plants. It is anticipated that preparation of the ESP application and interaction with NRC during the application review process will result not only in an ESP for the applicant(s) but also in the development of criteria and definition of processes, setting the precedent that facilitates ESPs for subsequent ESP applications. Because siting regulatory processes and acceptance criteria are contained in over 100 separate documents, comprehensive licensing and technical reviews were performed to establish whether the requirements and documentation are self-consistent, whether the acceptance criteria are sufficiently well-defined and clear, and whether the licensing process leading to the issuance of an ESP is unambiguously specified. The results of the technical and licensing evaluations are presented in this report. The purpose, background, and organization of the ESPDP is delineated in Section 1. Section 11 contains flowcharts defining siting application requirements, environmental report requirements, and emergency planning/preparedness requirements for ALWRS. The licensing and technical review results are presented in Section III.

  18. Variability amongst radiographers in the categorization of clinical acceptability for digital trauma radiography

    Science.gov (United States)

    Decoster, Robin; Toomey, Rachel; Smits, Dirk; Mol, Harrie; Verhelle, Filip; Butler, Marie-Louise

    2016-03-01

    Introduction: Radiographers evaluate anatomical structures to judge clinical acceptability of a radiograph. Whether a radiograph is deemed acceptable for diagnosis or not depends on the individual decision of the radiographer. Individual decisions cause variation in the accepted image quality. To minimise these variations definitions of acceptability, such as in RadLex, were developed. On which criteria radiographers attribute a RadLex categories to radiographs is unknown. Insight into these criteria helps to further optimise definitions and reduce variability in acceptance between radiographers. Therefore, this work aims the evaluation of the correlation between the RadLex classification and the evaluation of anatomical structures, using a Visual Grading Analysis (VGA) Methods: Four radiographers evaluated the visibility of five anatomical structures of 25 lateral cervical spine radiographs on a secondary class display with a VGA. They judged clinical acceptability of each radiograph using RadLex. Relations between VGAS and RadLex category were analysed with Kendall's Tau correlation and Nagelkerke pseudo-R². Results: The overall VGA score (VGAS) and the RadLex score correlate (rτ= 0.62, pscore. The reproduction of spinous processes (rτ=0.67, pscore. Conclusion: RadLex scores and VGAS correlate positively, strongly and significantly. The predictive value of bony structures may support the use of these in the judgement of clinical acceptability. Considerable inter-observer variations in the VGAS within a certain RadLex category, suggest that observers use of observer specific cut-off values.

  19. A systematic review of patient acceptance of consumer health information technology.

    Science.gov (United States)

    Or, Calvin K L; Karsh, Ben-Tzion

    2009-01-01

    A systematic literature review was performed to identify variables promoting consumer health information technology (CHIT) acceptance among patients. The electronic bibliographic databases Web of Science, Business Source Elite, CINAHL, Communication and Mass Media Complete, MEDLINE, PsycArticles, and PsycInfo were searched. A cited reference search of articles meeting the inclusion criteria was also conducted to reduce misses. Fifty-two articles met the selection criteria. Among them, 94 different variables were tested for associations with acceptance. Most of those tested (71%) were patient factors, including sociodemographic characteristics, health- and treatment-related variables, and prior experience or exposure to computer/health technology. Only ten variables were related to human-technology interaction; 16 were organizational factors; and one was related to the environment. In total, 62 (66%) were found to predict acceptance in at least one study. Existing literature focused largely on patient-related factors. No studies examined the impact of social and task factors on acceptance, and few tested the effects of organizational or environmental factors on acceptance. Future research guided by technology acceptance theories should fill those gaps to improve our understanding of patient CHIT acceptance, which in turn could lead to better CHIT design and implementation.

  20. Study on Influencing Factor Analysis and Application of Consumer Mobile Commerce Acceptance

    Science.gov (United States)

    Li, Gaoguang; Lv, Tingjie

    Mobile commerce (MC) refers to e-commerce activities carried out using a mobile device such as a phone or PDA. With new technology, MC will be rapidly growing in the near future. At the present time, what factors making consumer accept MC and what MC applications are acceptable by consumers are two of hot issues both for MC providers and f or MC researchers. This study presents a proposed MC acceptance model that integrates perceived playfulness, perceived risk and cost into the TAM to study which factors affect consumer MC acceptance. The proposed model includes five variables, namely perceived risk, cost, perceived usefulness, perceived playfulness, perceived ease of use, perceived playfulness. Then, using analytic hierarchy process (AHP) to calculate weight of criteria involved in proposed model. Finally, the study utilizes fuzzy comprehensive evaluation method to evaluate MC applications accepted possibility, and then a MC application is empirically tested using data collected from a survey of MC consumers.

  1. Emotional and Spiritual Quotient Approach Improve Biology Education Students’ Acceptance of Evolution Theory

    Science.gov (United States)

    Darussyamsu, R.; Fadilah, M.; Putri, D. H.

    2018-04-01

    Emotional and spiritual aspect is one of main factors that influence students’ acceptance of a theory. This study aim to measure university students’ acceptance of evolution by learns evolution using emotional and spiritual quotient (ESQ) approach. This is a quasi-experimental research using one shot case study design with the subject 36 biology educational students at Biology Department, Faculty of Mathematics and Natural Science, Universitas Negeri Padang. Data collected using the MATE instrument by Rutledge and Warden (2000) after the students learn evolution for eight meetings since January until March 2017. The result showed that by learning evolution theory combine with ESQ aspects increase students acceptance from very low become moderate acceptance. It concluded that ESQ aspects can improve students’ acceptance of evolution. Any criteria depend on it are discussed.

  2. Nuclear waste in public acceptance

    International Nuclear Information System (INIS)

    Vastchenko, Svetlana V.

    2003-01-01

    The existing problem on a faithful acceptance of nuclear information by population is connected, to a considerable extent, with a bad nuclear 'reputation' because of a great amount of misrepresented and false information from 'the greens'. In contrast to a bare style of professionals often neglecting an emotional perception, a loud voice of 'the greens' appeals both to the head, and to the heart of the audience. People pattern their behaviour weakly on problems of safe application of different irradiation sources in industry, conditions of life, medicine and everyday life. Radiation danger of some sources is often exaggerated (computers, nuclear technologies, radiation treatment) and the danger of the others is, on the contrary, underestimated (nuclear and roentgen methods of diagnostics and medical treatment). The majority of our citizens do not know which level of radiation is normal and safe, which ways radioactive substances intake into the organism of a human being and how to diminish the dose load on the organism by simple measures. Only specialists can be orientated themselves in a great number of radiation units. Low level of knowledge of the population and false conceptions are connected with the fact that they are mainly informed about nuclear technologies from mass media, where the voice of 'Greenpeace' is loudly sounded, but they often give misrepresented and false information doing it in the very emotional form. In contrast to them, scientists-professionals often ignore a sensitive part of apprehending of information and do not attach importance to it. As a rule, the style of specialists is of a serious academician character when they meet with the public. People preconception to nuclear waste and distrust to a positive information concerning nuclear technologies are explained, to a considerable extent, by a bivalent type of thinking when people operate by two opposite conceptions only, such as 'there is' or 'there is not' (there is or there is not

  3. Nuclear waste in public acceptance

    Energy Technology Data Exchange (ETDEWEB)

    Vastchenko, Svetlana V. [Joint Institute for Power and Nuclear Research - Sosny / National Academy of Science, A.K.Krasin Str., 99, Minsk 220109 (Belarus)

    2003-07-01

    The existing problem on a faithful acceptance of nuclear information by population is connected, to a considerable extent, with a bad nuclear 'reputation' because of a great amount of misrepresented and false information from 'the greens'. In contrast to a bare style of professionals often neglecting an emotional perception, a loud voice of 'the greens' appeals both to the head, and to the heart of the audience. People pattern their behaviour weakly on problems of safe application of different irradiation sources in industry, conditions of life, medicine and everyday life. Radiation danger of some sources is often exaggerated (computers, nuclear technologies, radiation treatment) and the danger of the others is, on the contrary, underestimated (nuclear and roentgen methods of diagnostics and medical treatment). The majority of our citizens do not know which level of radiation is normal and safe, which ways radioactive substances intake into the organism of a human being and how to diminish the dose load on the organism by simple measures. Only specialists can be orientated themselves in a great number of radiation units. Low level of knowledge of the population and false conceptions are connected with the fact that they are mainly informed about nuclear technologies from mass media, where the voice of 'Greenpeace' is loudly sounded, but they often give misrepresented and false information doing it in the very emotional form. In contrast to them, scientists-professionals often ignore a sensitive part of apprehending of information and do not attach importance to it. As a rule, the style of specialists is of a serious academician character when they meet with the public. People preconception to nuclear waste and distrust to a positive information concerning nuclear technologies are explained, to a considerable extent, by a bivalent type of thinking when people operate by two opposite conceptions only, such as 'there is

  4. Reflexive criteria of sociological research

    Directory of Open Access Journals (Sweden)

    R T Ubaydullaeva

    2014-12-01

    Full Text Available The article is devoted to the sociological criteria of explaining the way of thinking and actions of subjects, their spiritual and moral positions and intellectual forces that form the laws of social life. The author seeks to adapt such categories as ‘meaning of life’, ‘human dignity’, ‘rationality’ etc. for the purposes of sociological analysis by methodological construction of some real life dichotomies such as ‘subjective meaning and social function’, ‘the real and the ideal’, ‘the demanded and the excluded’. Thus, the author studies economic, political and technical processes in terms of both positivity and negativity of social interaction and states that given the increasing differentiation of the society and the contradictory trends of social development the reflexive criteria that take into account the socio-cultural nature of the man help to find one’s own model of development.

  5. New facility shield design criteria

    International Nuclear Information System (INIS)

    Howell, W.P.

    1981-07-01

    The purpose of the criteria presented here is to provide standard guidance for the design of nuclear radiation shields thoughout new facilities. These criteria are required to assure a consistent and integrated design that can be operated safely and economically within the DOE standards. The scope of this report is confined to the consideration of radiation shielding for contained sources. The whole body dose limit established by the DOE applies to all doses which are generally distributed throughout the trunk of the body. Therefore, where the whole body is the critical organ for an internally deposited radionuclide, the whole body dose limit applies to the sum of doses received must assure control of the concentration of radionuclides in the building atmosphere and thereby limit the dose from internal sources

  6. Soil decontamination criteria report, November 1980

    International Nuclear Information System (INIS)

    Riordan, G.A.

    1980-01-01

    A program to access the extent of transuranic soil contamination at DOE sites and to develop methods for their decontamination is underway at Rocky Flats. As part of this program, acceptable soil contamination levels for plutonium proposed by a number of authorities over the past couple of decades were reviewed. From this review, goals for soil decontamination work are proposed. These goals, which relate to the disposition of the products of a decontamination process, are summarized as follows (dpm/g will refer to disintegrations per minute of transuranic nuclides per gram of soil): soil fractions having less than 30 dpm can be disposed of as surface soil with unrestricted usage. Fine soil fractions (less than 100 μm) that have less than 500 dpm and coarse soil fractions that have less than 1000 dpm can be disposed of as subsurface soil as long as usage is controlled to ensure compliance with EPA dosage guidance. Soil concentrates that have an activity greater than the above values but less than 22,000 dpm should be interred in an approved, low level waste burial site. Soil concentrates that are greater than 22,000 dpm should be stored as retrievable waste. Changes in the technical and legal areas of soil decontamination are rapid. Permissible soil decontamination levels will change as will decontamination technology and the ability to monitor the effectiveness of the decontamination processes. As a result, annual updates of decontamination criteria, goals, and monitoring are expected

  7. Stress criteria for nuclear vessel concrete

    International Nuclear Information System (INIS)

    Costes, D.

    1975-01-01

    Concrete nuclear vessels are submitted to prestressing forces which limit tensile stresses in concrete when the vessel is under pressure with thermal gradients. Hence, the most severe conditions for concrete appear when the vessel is prestressed and not submitted to internal pressure. The triaxial states of stress in the concrete may be computed postulating elastic or other behavior and compared with safe limits obtained from rupture tests and fatigue tests. The first part of the paper, recalls experimental rupture results and the acceptability procedures currently used. Criteria founded on the lemniscoid surfaces are proposed, parameters for which are obtained by various tests and safety considerations. In the second part, rupture tests are reported on small, thick, cylindrical vessels submitted to external hydraulic pressure simulating prestressing forces. Materials used are plain concrete, microconcrete, marble and graphite. The strengths obtained are much higher than those which could be elastically computed, triaxial rupture states being provided by previous experiments. Such results may be due to a plastic stress redistribution before fracture and to stabilizing effects of stress gradients around the more stressed areas. Fatigue tests by external hydraulic loading are reported [fr

  8. Monitoring programmes for internal exposure: designing criteria

    International Nuclear Information System (INIS)

    Rojo, Ana M.; Gomez Parada, Ines.

    2007-01-01

    The purpose of this document is to offer guidance for the decision whether a monitoring programme is required and how it should be designed. It can be also used as a tool for making the standing programmes consistent with the most recent publications on internal dosimetry, such as ISO 20553 'Monitoring of workers occupationally exposed to a risk of internal contamination with radioactive material', specific publications of the IAEA and ICRP, and including the conclusions of the OMINEX Project ('Optimisation of Monitoring for Internal Exposures') and IDEAS Project. It is established that the general purpose of the monitoring is verify that each worker is protected adequately against risks from radionuclide intakes and document that the protection complies with legal requirements. The criteria for a particular monitoring programme designing is based on the magnitude of the probable intake and the possibility of detecting a significant event when it occurs. So, the risk assessment for each work process must be evaluated and each worker is classified accordingly. This classification implies the acceptance of reference effective dose values (1 y 6 mSv/y ). (author) [es

  9. NSSS supplier's response to differing safety criteria

    Energy Technology Data Exchange (ETDEWEB)

    Cremades, J; Filkin, R; Franke, T [Westinghouse Electric Nuclear Energy Systems Europe (WENESE), Brussels (Belgium)

    1980-11-01

    The limited progress achieved to date in harmonizing national criteria has led to the development of designs which include the most common national requirements. Progress towards harmonization of safety criteria can be accelerated by expanding the IAEA leadership and co-ordination activities, and implementing an integrated approach to criteria development. National and International safety criteria are examined.

  10. Evaluating Dependence Criteria for Caffeine

    OpenAIRE

    Striley, Catherine L.W.; Griffiths, Roland R.; Cottler, Linda B.

    2011-01-01

    Background: Although caffeine is the most widely used mood-altering drug in the world, few studies have operationalized and characterized Diagnostic and Statistical Manual IV (DSM-IV) substance dependence criteria applied to caffeine. Methods: As a part of a nosological study of substance use disorders funded by the National Institute on Drug Abuse, we assessed caffeine use and dependence symptoms among high school and college students, drug treatment patients, and pain clinic patients who re...

  11. Radiological criteria in nuclear emergencies

    International Nuclear Information System (INIS)

    Carrillo, D.; Diaz de la Cruz, F.

    1985-01-01

    It is pretended to enlighten the way to adopt the recommendations, from supranational organizations or the practices followed in other countries, to the peculiarities existing in Spain for the specific case of Nuclear Emergency Response Planning. The adaptation has been focalized in the criteria given by the Spanish Nuclear Safety Council and has taken into account the radiological protection levels, which have been considered adequate for Spanish population in case of nuclear accidents. (author)

  12. Sampling criteria in multicollection searching.

    Science.gov (United States)

    Gilio, A.; Scozzafava, R.; Marchetti, P. G.

    In the first stage of the document retrieval process, no information concerning relevance of a particular document is available. On the other hand, computer implementation requires that the analysis be made only for a sample of retrieved documents. This paper addresses the significance and suitability of two different sampling criteria for a multicollection online search facility. The inevitability of resorting to a logarithmic criterion in order to achieve a "spread of representativeness" from the multicollection is demonstrated.

  13. Position paper: Seismic design criteria

    International Nuclear Information System (INIS)

    Farnworth, S.K.

    1995-01-01

    The purpose of this paper is to document the seismic design criteria to be used on the Title 11 design of the underground double-shell waste storage tanks and appurtenant facilities of the Multi-Function Waste Tank Facility (MWTF) project, and to provide the history and methodologies for determining the recommended Design Basis Earthquake (DBE) Peak Ground Acceleration (PGA) anchors for site-specific seismic response spectra curves. Response spectra curves for use in design are provided in Appendix A

  14. Design criteria for the structural analysis of shipping cask containment vessels

    International Nuclear Information System (INIS)

    Anon.

    1979-01-01

    10 CFR Part 71, Sections 71.35 and 71.36, require that packages used to transport radioactive materials meet specified normal and hypothetical accident conditions. Acceptable design criteria are presented for use in the structural analysis of the containment vessels of Type B packages used to transport irradiated nuclear fuel. Alternative design criteria meeting the structural requirements of 10 CFR Part 71, Section 71.35 and 71.36, may also be used

  15. Repository operational criteria comparative analysis

    International Nuclear Information System (INIS)

    Hageman, J.P.; Chowdhury, A.H.

    1994-06-01

    The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations considering the interfaces among the components of the regulations and impacts of any potential changes to those regulations. The ROC task addresses regulatory criteria and uncertainties related to the preclosure aspects of the geologic repository. Those parts of 10 CFR Part 60 that require routine guidance or minor changes to the rule were addressed in Hageman and Chowdhury, 1992. The ROC task shows a possible need for further regulatory clarity, by major changes to the rule, related to the design bases and siting of a geologic repository operations area and radiological emergency planning in order to assure defense-in-depth. The analyses, presented in this report, resulted in the development and refinement of regulatory concepts and their supporting rationale for recommendations for potential major changes to 10 CFR Pan 0 regulations

  16. Consumer acceptance of irradiated foods

    International Nuclear Information System (INIS)

    Feenstra, M.H.; Scholten, A.H.

    1991-01-01

    Although the first experiments on food irradiation were carried out in 1916 in Sweden, food irradiation, is for consumers, a relatively new technology. From the sixties food irradiation has been applied more and more, so that the consumer movement has become alert to this technology. Since then a lot of controversies have arisen in the literature about wholesomeness, safety, effects, etc. Food irradiation is currently permitted on a small scale in about 30 countries; in some countries or states food irradiation has been put under a ban (e.g. Australia, New Zealand, New Jersey). The World Health Organization (WHO) and the Food and Agriculture Organization of the United Nations (FAO) have, however, chosen food irradiation as a safe and sound method for preserving and improving the safety of food. Reactions on the part of the consumer organizations of many countries are however not in favour of or are even opposed to food irradiation. In this chapter consumer acceptance related to technological developments is described, then the convergence of the consumer movement on public opinion and concern on food irradiation is discussed. The need for labelling of irradiated food products is discussed and finally recommendations are given of ways to change consumers attitudes to food irradiation. (author)

  17. Acceptance and adoption of biofortified crops in low- and middle-income countries: a systematic review

    Science.gov (United States)

    Talsma, Elise F; Melse-Boonstra, Alida; Brouwer, Inge D

    2017-01-01

    Context: Biofortification of staple crops is a promising strategy for increasing the nutrient density of diets in order to improve human health. The willingness of consumers and producers to accept new crop varieties will determine whether biofortification can be successfully implemented. Objective: This review assessed sensory acceptance and adoption of biofortified crops and the determining factors for acceptance and adoption among consumers and producers in low- and middle-income countries. Data sources: PubMed, Scopus, and Web of Science were searched for published reports. Unpublished studies were identified using an internet search. Study selection: From a total of 1669 records found, 72 primary human research studies published in English or Spanish met the criteria for inclusion. Data extraction: Data were extracted from each identified study using a standardized form. Results: Sensory acceptability (n = 40) was the most common topic of the studies, followed by determinants of acceptance (n = 25) and adoption (n = 21). Of crops included in the studies, sweet potato and maize were the most studied, whereas rice and pearl-millet were the least investigated. Overall, sensory acceptance was good, and availability and information on health benefits of the crops were the most important determinants of acceptance and adoption. Conclusions: Changes to the sensory qualities of a crop, including changes in color, did not act as an obstacle to acceptance of biofortified crops. Future studies should look at acceptance of biofortified crops after they have been disseminated and introduced on a wide-scale. PMID:29028269

  18. Acceptability of HIV self-testing: a systematic literature review.

    Science.gov (United States)

    Krause, Janne; Subklew-Sehume, Friederike; Kenyon, Chris; Colebunders, Robert

    2013-08-08

    The uptake of HIV testing and counselling services remains low in risk groups around the world. Fear of stigmatisation, discrimination and breach of confidentiality results in low service usage among risk groups. HIV self-testing (HST) is a confidential HIV testing option that enables people to find out their status in the privacy of their homes. We evaluated the acceptability of HST and the benefits and challenges linked to the introduction of HST. A literature review was conducted on the acceptability of HST in projects in which HST was offered to study participants. Besides acceptability rates of HST, accuracy rates of self-testing, referral rates of HIV-positive individuals into medical care, disclosure rates and rates of first-time testers were assessed. In addition, the utilisation rate of a telephone hotline for counselling issues and clients` attitudes towards HST were extracted. Eleven studies met the inclusion criteria (HST had been offered effectively to study participants and had been administered by participants themselves) and demonstrated universally high acceptability of HST among study populations. Studies included populations from resource poor settings (Kenya and Malawi) and from high-income countries (USA, Spain and Singapore). The majority of study participants were able to perform HST accurately with no or little support from trained staff. Participants appreciated the confidentiality and privacy but felt that the provision of adequate counselling services was inadequate. The review demonstrates that HST is an acceptable testing alternative for risk groups and can be performed accurately by the majority of self-testers. Clients especially value the privacy and confidentiality of HST. Linkage to counselling as well as to treatment and care services remain major challenges.

  19. A Preliminary Investigation of Acceptance and Commitment Therapy as a Treatment for Marijuana Dependence in Adults

    Science.gov (United States)

    Twohig, Michael P.; Shoenberger, Deacon; Hayes, Steven C.

    2007-01-01

    In this investigation, 3 adults who met criteria for marijuana dependence were treated using an abbreviated version of acceptance and commitment therapy (ACT). The treatment was delivered in eight weekly 90-min individual sessions. The effects of the intervention were assessed using a nonconcurrent multiple baseline across participants design.…

  20. How Turkey Meets MPOWER Criteria?

    Directory of Open Access Journals (Sweden)

    Nazmi Bilir

    2013-02-01

    Full Text Available In 2003 World Health Assembly adopted an international treaty on tobacco control; FCTC, Framework Convention on Tobacco Control. Five year later World Health Organization (WHO declared the six effective approach for tobacco control, under the name of MPOWER. In the following years, WHO evaluated the level of implementation of MPOWER criteria in the countries. In this article, how Turkey implemented these six criteria will be discussed. Monitor tobacco use and prevention policies: Monitoring of tobacco use prevalence has been successfully monitored in Turkey through Global Adult Tobacco Survey, Global Youth Tobacco Survey and Health Professionals Tobacco Use Survey. Nevertheless, monitoring of tobacco industry activities was not successfully implemented. Protect people from tobacco smoke: Smoking was banned in most of the indoor public places in Turkey since 1996, and Turkey became a complete smoke-free country by the exposion of smoke-free places including the hospitality workplaces in 2008. Offer help to quit tobacco use: Although smoking cessation services has been a bit late in Turkey, availability of smoking cessation drugs and the establishment of free quitline services made Turkey successful in this regard. Warn about the dangers of tobacco: Since 1996, all TV channels have a duty of broadcasting programs on harms of tobacco use, not less than 90 minutes in a month and it has been implemented successfully. Additionally written messages indicating harms of tobacco has been printed on the packs since 1988 and pictures was added in 2010. But since the average surface area covered by the messages in less than 50% of the total surface of the pack, Turkey was not regarded as to meet the requirement. Enforce bans on tobacco advertising, promotion and sponsorship: All kinds of tobacco advertisement and promotion was banned by the Law in 1996. But the tobacco products was not in closed boxes at the sales points. Turkey was not found as successful

  1. Waste Acceptance System Requirements document (WASRD)

    International Nuclear Information System (INIS)

    1993-01-01

    This Waste Acceptance System Requirements document (WA-SRD) describes the functions to be performed and the technical requirements for a Waste Acceptance System for accepting spent nuclear fuel (SNF) and high-level radioactive waste (HLW) into the Civilian Radioactive Waste Management System (CRWMS). This revision of the WA-SRD addresses the requirements for the acceptance of HLW. This revision has been developed as a top priority document to permit DOE's Office of Environmental Restoration and Waste Management (EM) to commence waste qualification runs at the Savannah River Site's (SRS) Defense Waste Processing Facility (DWPF) in a timely manner. Additionally, this revision of the WA-SRD includes the requirements from the Physical System Requirements -- Accept Waste document for the acceptance of SNF. A subsequent revision will fully address requirements relative to the acceptance of SNF

  2. Acceptability of GM foods among Pakistani consumers

    Science.gov (United States)

    Ali, Akhter; Rahut, Dil Bahadur; Imtiaz, Muhammad

    2016-01-01

    ABSTRACT In Pakistan majority of the consumers do not have information about genetically modified (GM) foods. In developing countries particularly in Pakistan few studies have focused on consumers' acceptability about GM foods. Using comprehensive primary dataset collected from 320 consumers in 2013 from Pakistan, this study analyzes the determinants of consumers' acceptability of GM foods. The data was analyzed by employing the bivariate probit model and censored least absolute deviation (CLAD) models. The empirical results indicated that urban consumers are more aware of GM foods compared to rural consumers. The acceptance of GM foods was more among females' consumers as compared to male consumers. In addition, the older consumers were more willing to accept GM food compared to young consumers. The acceptability of GM foods was also higher among wealthier households. Low price is the key factor leading to the acceptability of GM foods. The acceptability of the GM foods also reduces the risks among Pakistani consumers. PMID:27494790

  3. Acceptability of GM foods among Pakistani consumers.

    Science.gov (United States)

    Ali, Akhter; Rahut, Dil Bahadur; Imtiaz, Muhammad

    2016-04-02

    In Pakistan majority of the consumers do not have information about genetically modified (GM) foods. In developing countries particularly in Pakistan few studies have focused on consumers' acceptability about GM foods. Using comprehensive primary dataset collected from 320 consumers in 2013 from Pakistan, this study analyzes the determinants of consumers' acceptability of GM foods. The data was analyzed by employing the bivariate probit model and censored least absolute deviation (CLAD) models. The empirical results indicated that urban consumers are more aware of GM foods compared to rural consumers. The acceptance of GM foods was more among females' consumers as compared to male consumers. In addition, the older consumers were more willing to accept GM food compared to young consumers. The acceptability of GM foods was also higher among wealthier households. Low price is the key factor leading to the acceptability of GM foods. The acceptability of the GM foods also reduces the risks among Pakistani consumers.

  4. Physical system requirements - Accept waste

    International Nuclear Information System (INIS)

    1992-08-01

    The Nuclear Waste Policy Act (NWPA) assigned to the Department of Energy (DOE) the responsibility for managing the disposal of spent nuclear fuel and high-level radioactive waste and established the Office of Civilian Radioactive Waste Management (OCRWM) for that purpose. The Secretary of Energy, in his November 1989 report to Congress (DOE/RW-0247), announced new initiatives for the conduct of the Civilian Radioactive Waste Management (CRWM) program. One of these initiatives was to establish improved management structure and procedures. In response, OCRWM performed a management study and the OCRWM Director subsequently issued the Management Systems improvement Strategy (MSIS) on August 10, 1990, calling for a rigorous implementation of systems engineering principles with a special emphasis on functional analysis. The functional analysis approach establishes a framework for integrating the program management efforts with the technical requirements analysis into a single, unified, and consistent program. This approach recognizes that just as the facilities and equipment comprising the physical waste management system must perform certain functions, so must certain programmatic and management functions be performed within the program in order to successfully bring the physical system into being. Thus, a comprehensive functional analysis effort has been undertaken which is intended to: Identify the functions that must be performed to fulfill the waste disposal mission; Identify the corresponding requirements imposed on each of the functions; and Identify the conceptual architecture that will be used to satisfy the requirements. The principal purpose of this requirements document is to present the results that were obtained from the conduct of a functional analysis effort for the Accept Waste mission

  5. Radiological control criteria for materials considered for recycle and reuse

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Hill, R.L.; Aaberg, R.L.; Wallo, A. III.

    1995-01-01

    Pacific Northwest Laboratory (PNL) is conducting technical analyses to support the U.S. Department of Energy (DOE), Office of Environmental Guidance, Air, Water, and Radiation Division (DOE/EH-232) in developing radiological control criteria for recycling or reuse of metals or equipment containing residual radioactive contamination from DOE operations. The criteria, framed as acceptable concentrations for release of materials for recycling or reuse, are risk-based and were developed through analysis of generic radiation exposure scenarios and pathways. The analysis includes evaluation of relevant radionuclides, potential mechanisms of exposure, and non-health-related impacts of residual radioactivity on electronics and film. The analysis considers 42 key radionuclides that DOE operations are known to generate and that may be contained in recycled or reused metals or equipment. The preliminary results are compared with similar results reported by the International Atomic Energy Agency, by radionuclide grouping. (author)

  6. Radiological control criteria for materials considered for recycle and reuse

    International Nuclear Information System (INIS)

    Kennedy, W.E. Jr.; Hill, R.L.; Aaberg, R.L.; Wallo, A. III

    1994-11-01

    Pacific Northwest Laboratory (PNL) is conducting technical analyses to support the US Department of Energy (DOE), Office of Environmental Guidance, Air, Water, and Radiation Division (DOE/EH-232) in developing radiological control criteria for recycling or reuse of metals or equipment containing residual radioactive contamination from DOE operations. The criteria, framed as acceptable concentrations for release of materials for recycling or reuse, are risk-based and were developed through analysis of generic radiation exposure scenarios and pathways. The analysis includes evaluation of relevant radionuclides, potential mechanisms of exposure, and non-health-related impacts of residual radioactivity on electronics and film. The analysis considers 42 key radionuclides that DOE operations are known to generate and that may be contained in recycled or reused metals or equipment. Preliminary results are compared with similar results reported by the International Atomic Energy Agency, by radionuclide grouping

  7. Radiological design criteria for fusion power test facilities

    International Nuclear Information System (INIS)

    Singh, M.S.; Campbell, G.W.

    1982-01-01

    The quest for fusion power and understanding of plasma physics has resulted in planning, design, and construction of several major fusion power test facilities, based largely on magnetic and inertial confinement concepts. We have considered radiological design aspects of the Joint European Torus (JET), Livermore Mirror and Inertial Fusion projects, and Princeton Tokamak. Our analyses on radiological design criteria cover acceptable exposure levels at the site boundary, man-rem doses for plant personnel and population at large, based upon experience gained for the fission reactors, and on considerations of cost-benefit analyses

  8. Protection criteria from the non-ionizing radiations

    International Nuclear Information System (INIS)

    Touzet, Rodolfo E.

    2004-01-01

    The first objective of the protection philosophy is to determinate the relation reason-effect in order to establish the exposition thresholds to acceptable values. To establish the radioprotection criteria is important to considerate the following: a-) The damage and effects of the non-ionizing radiation; b-) The physical aspects of the fields exposition; and c-) The dosimetry of the involucrate tissues. The non-ionizing radiation includes the optics radiations (ultraviolet, visible, infrared and laser), and the electromagnetic radiations (microwave, radars, magnetic and electrostatics fields)

  9. Suggested non-proliferation criteria for commercial nuclear fuel cycles

    International Nuclear Information System (INIS)

    Laney, R.V.; Heubotter, P.R.

    1978-01-01

    Based on the Administration's policy to prevent nuclear weapons proliferation through diversion of fuel from commercial reactor fuel cycles, a ''benchmark'' set of nonproliferation criteria was prepared for the commercial nuclear fuel cycle. These criteria should eliminate incremental risks of proliferation beyond those inherent in the present generation of low-enriched-uranium-fueled reactors operating in a once-through mode, with internationally safeguarded storage of spent fuel. They focus on the balanced application of technical constraints consistent with the state of the technology, with minimal requirements for institutional constraints, to provide a basis for assessing the proliferation resistance of proposed fission power systems. The paper contains: (1) our perception of the nuclear energy policy and of the baseline proliferation risk accepted under this policy; (2) objectives for a reactor and fuel cycle strategy which address the technical, political, and institutional aspects of diversion and proliferation and, at the same time, satisfy the Nation's needs for efficient, timely, and economical utilization of nuclear fuel resources; (3) criteria which are responsive to these objectives and can therefore be used to screen proposed reactor and fuel cycle strategies; and (4) a rationale for these criteria

  10. Establishing endangered species recovery criteria using predictive simulation modeling

    Science.gov (United States)

    McGowan, Conor P.; Catlin, Daniel H.; Shaffer, Terry L.; Gratto-Trevor, Cheri L.; Aron, Carol

    2014-01-01

    Listing a species under the Endangered Species Act (ESA) and developing a recovery plan requires U.S. Fish and Wildlife Service to establish specific and measurable criteria for delisting. Generally, species are listed because they face (or are perceived to face) elevated risk of extinction due to issues such as habitat loss, invasive species, or other factors. Recovery plans identify recovery criteria that reduce extinction risk to an acceptable level. It logically follows that the recovery criteria, the defined conditions for removing a species from ESA protections, need to be closely related to extinction risk. Extinction probability is a population parameter estimated with a model that uses current demographic information to project the population into the future over a number of replicates, calculating the proportion of replicated populations that go extinct. We simulated extinction probabilities of piping plovers in the Great Plains and estimated the relationship between extinction probability and various demographic parameters. We tested the fit of regression models linking initial abundance, productivity, or population growth rate to extinction risk, and then, using the regression parameter estimates, determined the conditions required to reduce extinction probability to some pre-defined acceptable threshold. Binomial regression models with mean population growth rate and the natural log of initial abundance were the best predictors of extinction probability 50 years into the future. For example, based on our regression models, an initial abundance of approximately 2400 females with an expected mean population growth rate of 1.0 will limit extinction risk for piping plovers in the Great Plains to less than 0.048. Our method provides a straightforward way of developing specific and measurable recovery criteria linked directly to the core issue of extinction risk. Published by Elsevier Ltd.

  11. International Political Actorness of the European Union: Evaluation Criteria

    Directory of Open Access Journals (Sweden)

    GNATYUK N.N.

    2014-06-01

    Full Text Available The European Union is a completely new international entity which is hard to evaluate using traditional criteria of political actorness. Its active international presence stimulates the modeling of international actor features beyond the scope of “state-international organization” scheme. The concept of international actorness serves as a starting point for the development of appropriate analytical model. Unlike the traditional state-centered approaches which define an international actor through its affiliation witch the international system, this concept operates at the internal level of international entity and at the international structure level. Furthermore, both of these levels are treated as ontologically neutral and mutually constitutive. This basic theoretical scheme is used for elaboration of evaluation criteria of political actorness. The proposed system of criteria is based on drawing, synthesizing and developing the main writings on “new international actors” since the times of classic work by Carol A. Cosgrove and Kenneth J. Twitchett. The key elements of actorness assessed in this article include defining of capacity to act on the global scene as well as the acceptance by other actors and by international system as a whole. At the internal level, the EU’s actor capacity is measured by assessing its core elements ranging from core aspects, such as autonomy, authority, actor capability, coherence and cohesion to identity aspects. On the external level, the decisive criteria are recognition and acceptance by others which reflect expectations and perceptions of the EU. The proposed approach of evaluating the international actorness enables us to consider the political activity of the EU on the basis of coordinated system of interaction between the variables of international and domestic levels of the analysis. Furthermore, this contributes to the development of cumulative, coherent, and comprehensive theory of international

  12. Productive Regions: Criteria and Classification

    Directory of Open Access Journals (Sweden)

    Vlasyuk L. I.

    2012-03-01

    Full Text Available An official statistical dataset for 80 territorial subjects of the Russian Federation for 2000, 2007 and 2009 has proved the hypothesis that, under the neoclassical concept, the resources move to regions with the highest marginal productivity of the factors of production, which leads to the accumulation of investment resources, while providing financial and social efficiency. Based on cluster analysis by three performance criteria, productive regions are identified, which are dominated by regions productive in the extraction of minerals. It is shown that the stability of the factors’ distribution in space determines the current and future specialization of regional economies

  13. Training review criteria and procedures

    International Nuclear Information System (INIS)

    1993-01-01

    This document provides direction to NRC personnel for reviewing training programs at nuclear power plants to verify compliance with the requirements of 10 CFR 50. 120 and 10 CFR 55 as applicable. It describes the process for evaluating the effectiveness of training programs, provides aids for collection of information during interviews and observations, and provides criteria for evaluating the implementation of a systems approach to training. This document is not intended to have the effect of a regulation, it establishes no binding requirements or interpretations of NRC regulations. It is intended as guidance only

  14. 105K West Isolation Barrier Acceptance Test results

    International Nuclear Information System (INIS)

    McCracken, K.J.; Irwin, J.J.

    1995-01-01

    The objective of this document is to report and interpret the findings of the isolation barrier acceptance tests performed in 105KW/100K. The tests were performed in accordance with the test plan and acceptance test procedure. The test report contains the test data. This document compares the test data against the criteria. A discussion of the leak rate analytical characterization describes how the flow characteristics flow rate will be determined using the test data from the test report. Two modes of water loss were considered; basin and/or discharge chute leakage, and evaporation. An initial test established baseline leakage data and instrumentation performance. Test 2 evaluated the sealing performance of the isolation barrier by inducing an 11 in. (27.9 cm) level differential across the barrier. The leak rate at this 11 in. (27.9 cm) level is extrapolated to the 16 ft. (4.9 m) level differential postulated in the DBE post seismic event. If the leak rate, adjusted for evaporation and basin leakage (determined from Test 1), is less than the SAR limit of 1,500 gph (5,680 lph) at a 16 ft (4.9 m) level differential, the barriers pass the acceptance test

  15. Seismic design criteria for the system 80+ advanced light water reactor

    International Nuclear Information System (INIS)

    Manrique, M.A.; Dermitzakis, S.N.; Gerdes, L.D.; Kennedy, R.P.; Idriss, I.M.; Cassidy, J.R.

    1991-01-01

    This paper presents the development of seismic design criteria in support of design certification by the Nuclear Regulatory Commission (NRC) of the ABB-Combustion Engineering's System 80+ Standard Design. The design certification effort is sponsored by the US Department of Energy (DOE). The development of the design criteria included: (a) development of the seismic control motion, (b) development of generic soil profiles for anticipated sites, (c) generation of in-structure response spectra and design loads for structures and equipment through soil-structure interaction (SSI) analyses, and (d) acceptance criteria for future construction sites

  16. OTM Machine Acceptance: In the Arab Culture

    Science.gov (United States)

    Rashed, Abdullah; Santos, Henrique

    Basically, neglecting the human factor is one of the main reasons for system failures or for technology rejection, even when important technologies are considered. Biometrics mostly have the characteristics needed for effortless acceptance, such as easiness and usefulness, that are essential pillars of acceptance models such as TAM (technology acceptance model). However, it should be investigated. Many studies have been carried out to research the issues of technology acceptance in different cultures, especially the western culture. Arabic culture lacks these types of studies with few publications in this field. This paper introduces a new biometric interface for ATM machines. This interface depends on a promising biometrics which is odour. To discover the acceptance of this biometrics, we distributed a questionnaire via a web site and called for participation in the Arab Area and found that most respondents would accept to use odour.

  17. Ventilation criteria for IDMS facility

    International Nuclear Information System (INIS)

    Lambert, D.P.

    1996-01-01

    Both Facility Evaluation Board (FEB) reviews of the Integrated DWPF Melter System (IDMS) have identified the inconsistency of the current IDMS Process Hazards Review (PHR) versus actual IDMS practice as regards the criteria to contain air borne pollutants that may be present in the Process Room (e.g. benzene and mercury). The PHR states that a 1.0 in. wc pressure differential be maintained between the IDMS Process Room and Building 672-T. In addition, the PHR further specifies that the linear velocity through openings into the Process Room (e.g. open doors) be equal to or greater than 150 fpm. Finally, the PHR recommended that mercury vapor and benzene monitors be installed in the Process Room ventilation exhaust to alert personnel to the presence of vapors of benzene and/or mercury before entering the Process Room. This report summarizes the results of reassessment of these criteria and the specific recommendation for permanent installation of mercury and benzene vapor monitors in the vapor exhaust of the Process Room

  18. Donor selection criteria and procurement

    International Nuclear Information System (INIS)

    Agcaoili, N.R.

    1999-01-01

    Donor selection is one of the most important aspects of tissue banking practice. Without a good donor selection criteria, the results of any effort of trying to preserve tissues will have disastrous outcome for the recipient of these tissues. While with a very good and strict donor selection the Tissue Bank can guarantee safe and effective tissue allografts. There are significant aspects in the history and physical examination of the donor that must be emphasized. A donor exclusion criteria has also been formulated together with a list of all the needed laboratory examinations to eliminate possible diseases that may be transferred from the donor. The methods of procurement of tissue allografts from living and cadaver donors will be described. The limitations and advantages of each will be taken.There are also special restrictions that are important in the practice of removing the tissues from the donors. All the necessary equipment should be ready and the potential risk on the personnel should be known to all doing Tissue Banking

  19. Multi-criteria decision making with overlapping criteria

    Directory of Open Access Journals (Sweden)

    Mohammed Shahid Abdulla

    2012-09-01

    Full Text Available The evidential reasoning (ER algorithm for multi-criteria decision making (MCDM performs aggregation of the assessments of multiple experts, one each for every attribute (or subsystem or criterion of a given system. Two variants of ER are proposed, that handle a scenario where more than one expert assesses an attribute. The first algorithm handles the case of multiple experts who assess an attribute of a larger system. Experiments compare a modification of ER for this scenario which results in poorer detection. The second algorithm is used when experts have overlapping areas of expertise among the subsystems. A comparison is made with a variant of ER in the literature. Both algorithms are examples of novel ‘exclusive’ and ‘inclusive’ ER.

  20. Technical evaluation of draft ANSI Standard N13.30, ''performance criteria for radiobioassay''

    International Nuclear Information System (INIS)

    MacLellan, J.A.; Traub, R.J.

    1986-03-01

    The Pacific Northwest Laboratory (PNL) is conducting a research program to evaluate the appropriateness of criteria in the ANSI draft Standard N13.30, ''Performance Criteria for Radiobioassay.'' The evaluation has progressed parallel with the preparation of the Standard by evaluating the performance of existing bioassay laboratories against the criteria specified. Recommendations for revision of the Standard and implementation of a testing/accreditation program have been formulated based on study results. The current performance testing program includes both in-vivo counting and in-vitro sample measurements. Test criteria specified in the Standard include relative bias, relative precision, and acceptable minimum detectable activity (AMDA). Results to date have indicated that the acceptance criteria in the Standard are appropriate for the existing state of the industry and are achievable by a majority of the participating laboratories. Specific conclusions are that the AMDA criteria are most difficult for the laboratories to achieve; the relative bias criterion is second in difficulty, and the precision criterion presents no problem for the laboratories; most of the participating laboratories can meet the Standard; and failure rates may decrease as the laboratories become more knowledgeable of the performance criteria. 3 refs., 11 figs., 6 tabs

  1. 2013 SYR Accepted Poster Abstracts.

    Science.gov (United States)

    2013-01-01

    SYR 2013 Accepted Poster abstracts: 1. Benefits of Yoga as a Wellness Practice in a Veterans Affairs (VA) Health Care Setting: If You Build It, Will They Come? 2. Yoga-based Psychotherapy Group With Urban Youth Exposed to Trauma. 3. Embodied Health: The Effects of a Mind�Body Course for Medical Students. 4. Interoceptive Awareness and Vegetable Intake After a Yoga and Stress Management Intervention. 5. Yoga Reduces Performance Anxiety in Adolescent Musicians. 6. Designing and Implementing a Therapeutic Yoga Program for Older Women With Knee Osteoarthritis. 7. Yoga and Life Skills Eating Disorder Prevention Among 5th Grade Females: A Controlled Trial. 8. A Randomized, Controlled Trial Comparing the Impact of Yoga and Physical Education on the Emotional and Behavioral Functioning of Middle School Children. 9. Feasibility of a Multisite, Community based Randomized Study of Yoga and Wellness Education for Women With Breast Cancer Undergoing Chemotherapy. 10. A Delphi Study for the Development of Protocol Guidelines for Yoga Interventions in Mental Health. 11. Impact Investigation of Breathwalk Daily Practice: Canada�India Collaborative Study. 12. Yoga Improves Distress, Fatigue, and Insomnia in Older Veteran Cancer Survivors: Results of a Pilot Study. 13. Assessment of Kundalini Mantra and Meditation as an Adjunctive Treatment With Mental Health Consumers. 14. Kundalini Yoga Therapy Versus Cognitive Behavior Therapy for Generalized Anxiety Disorder and Co-Occurring Mood Disorder. 15. Baseline Differences in Women Versus Men Initiating Yoga Programs to Aid Smoking Cessation: Quitting in Balance Versus QuitStrong. 16. Pranayam Practice: Impact on Focus and Everyday Life of Work and Relationships. 17. Participation in a Tailored Yoga Program is Associated With Improved Physical Health in Persons With Arthritis. 18. Effects of Yoga on Blood Pressure: Systematic Review and Meta-analysis. 19. A Quasi-experimental Trial of a Yoga based Intervention to Reduce Stress and

  2. Technology Acceptance Model: A Survey of Literature

    Directory of Open Access Journals (Sweden)

    Priyanka Surendran

    2013-07-01

    Full Text Available The technology acceptance model has been a theory that is most widely used to explain an individual’s acceptance of an information system. This study has reviewed numerous literatures available in this area. The different studies in this area were evaluated to understand the modifications that were done on this model. The paper then tries to provide an insight on future trends in the technology acceptance model.

  3. Understanding Retailers’ Acceptance of Virtual Stores

    OpenAIRE

    Irene Y.L. Chen

    2010-01-01

    The acceptance of e-commerce among consumers has stimulated the rise of virtual stores. Increasing traditional retailers or people who do not have sufficient capital for maintaining a brick-and-mortar store have considered using virtual stores to reach global market. In the e-commerce literature, there has been rich research evidence concerning consumers’ acceptance of virtual stores. However, rigorous academic research on retailers’ acceptance of virtual stores is relatively scarce today. Th...

  4. Proposed Diagnostic Criteria for Smartphone Addiction.

    Science.gov (United States)

    Lin, Yu-Hsuan; Chiang, Chih-Lin; Lin, Po-Hsien; Chang, Li-Ren; Ko, Chih-Hung; Lee, Yang-Han; Lin, Sheng-Hsuan

    2016-01-01

    Global smartphone penetration has led to unprecedented addictive behaviors. The aims of this study are to develop diagnostic criteria of smartphone addiction and to examine the discriminative ability and the validity of the diagnostic criteria. We developed twelve candidate criteria for characteristic symptoms of smartphone addiction and four criteria for functional impairment caused by excessive smartphone use. The participants consisted of 281 college students. Each participant was systematically assessed for smartphone-using behaviors by psychiatrist's structured diagnostic interview. The sensitivity, specificity, and diagnostic accuracy of the candidate symptom criteria were analyzed with reference to the psychiatrists' clinical global impression. The optimal model selection with its cutoff point of the diagnostic criteria differentiating the smartphone addicted subjects from non-addicted subjects was then determined by the best diagnostic accuracy. Six symptom criteria model with optimal cutoff point were determined based on the maximal diagnostic accuracy. The proposed smartphone addiction diagnostic criteria consisted of (1) six symptom criteria, (2) four functional impairment criteria and (3) exclusion criteria. Setting three symptom criteria as the cutoff point resulted in the highest diagnostic accuracy (84.3%), while the sensitivity and specificity were 79.4% and 87.5%, respectively. We suggested determining the functional impairment by two or more of the four domains considering the high accessibility and penetration of smartphone use. The diagnostic criteria of smartphone addiction demonstrated the core symptoms "impaired control" paralleled with substance related and addictive disorders. The functional impairment involved multiple domains provide a strict standard for clinical assessment.

  5. Acceptance and Avoidance Processes at Different Levels of Psychological Recovery from Enduring Mental Illness.

    Science.gov (United States)

    Siqueira, Vinicius R; Oades, Lindsay G

    2015-01-01

    Objective. This study examined the use of psychological acceptance and experiential avoidance, two key concepts of Acceptance and Commitment Therapy (ACT), in the psychological recovery process of people with enduring mental illness. Method. Sixty-seven participants were recruited from the metropolitan, regional, and rural areas of New South Wales, Australia. They all presented some form of chronic mental illness (at least 12 months) as reflected in DSM-IV Axis I diagnostic criteria. The Acceptance and Action Questionnaire (AAQ-19) was used to measure the presence of psychological acceptance and experiential avoidance; the Recovery Assessment Scale (RAS) was used to examine the levels of psychological recovery; and the Scales of Psychological Well-Being was used to observe if there are benefits in utilizing psychological acceptance and experiential avoidance in the recovery process. Results. An analysis of objectively quantifiable measures found no clear correlation between the use of psychological acceptance and recovery in mental illness as measured by the RAS. The data, however, showed a relationship between psychological acceptance and some components of recovery, thereby demonstrating its possible value in the recovery process. Conclusion. The major contribution of this research was the emerging correlation that was observed between psychological acceptance and positive levels of psychological well-being among individuals with mental illness.

  6. A generic approach for steel containment vessel success criteria for severe accident loads

    International Nuclear Information System (INIS)

    Sammataro, R.F.; Solonick, W.R.; Edwards, N.W.

    1993-01-01

    Safety has been defined as the foremost design criterion for the Heavy Water New Production Reactor (NPR-HWR) by the U.S. DOE, Office of New Production Reactors (NP). The DOE-NP issued the Deterministic Severe Accident Criteria (DSAC) concept to guide the design of the NPR-HWR containment for resistance to severe accidents. The DSAC concept provides for a generic approach for containment vessel success criteria to predict the threshold of containment failure under severe accident loads. This concept consists of two parts: (1) Problem Statements and (2) Success Criteria. The paper is limited to a discussion of a success criteria. These criteria define acceptable containment response measures and limits for each problem statement. The criteria are based on the 'best estimate' of failure with no conservatism. Rather, conservatism, if required, is to be provided in the problem statements prepared by the designer and/or the regulatory authorities. The success criteria are presented on a multi-tiered basis for static pressure and temperature loadings, dynamic loadings, and missiles that may impact the containment. Within the static pressure and temperature loadings and the dynamic loadings, the criteria are separated into elastic analysis success criteria and inelastic analysis success criteria. Each of these areas, in turn, defines limits on either the stress or strain measures as well as on measures for buckling and displacements. The rationale upon which these criteria are based is contained in referenced documents. Rigorous validation of the criteria by comparison with results from analytical or experimental programs and application of the criteria to a containment design remain as future tasks. (orig./HP)

  7. 45 CFR 1176.3 - Criteria.

    Science.gov (United States)

    2010-10-01

    ... ENDOWMENT FOR THE HUMANITIES PART-TIME CAREER EMPLOYMENT § 1176.3 Criteria. Positions becoming vacant... to part-time. Among the criteria which may be used when conducting this review are: (a) Mission...

  8. 40 CFR 258.24 - Air criteria.

    Science.gov (United States)

    2010-07-01

    ... SOLID WASTE LANDFILLS Operating Criteria § 258.24 Air criteria. (a) Owners or operators of all MSWLFs... wastes, silvicultural wastes, landclearing debris, diseased trees, or debris from emergency cleanup...

  9. Qualitative vs. quantitative atopic dermatitis criteria

    DEFF Research Database (Denmark)

    Andersen, R M; Thyssen, J P; Maibach, H I

    2016-01-01

    This review summarizes historical aspects, clinical expression and pathophysiology leading to coining of the terms atopy and atopic dermatitis, current diagnostic criteria and further explore the possibility of developing quantitative diagnostic criteria of atopic dermatitis (AD) based on the imp...

  10. Separability criteria for genuine multiparticle entanglement

    NARCIS (Netherlands)

    Guhne, O.; Seevinck, M.P.|info:eu-repo/dai/nl/304847399

    2010-01-01

    We present a method to derive separability criteria for different classes of multiparticle entanglement, especially genuine multiparticle entanglement. The resulting criteria are necessary and sufficient for certain families of states. This, for example, completely solves the problem of classifying

  11. Separability Criteria for Genuine Multiparticle Entanglement

    NARCIS (Netherlands)

    Guehne, O.; Seevinck, M.P.

    2010-01-01

    We present a method to derive separability criteria for different classes of multiparticle entanglement, especially genuine multiparticle entanglement. The resulting criteria are necessary and sufficient for certain families of states. This, for example, completely solves the problem of classifying

  12. The Predictive Value of Selection Criteria in an Urban Magnet School

    Science.gov (United States)

    Lohmeier, Jill Hendrickson; Raad, Jennifer

    2012-01-01

    The predictive value of selection criteria on outcome data from two cohorts of students (Total N = 525) accepted to an urban magnet high school were evaluated. Regression analyses of typical screening variables (suspensions, absences, metropolitan achievement tests, middle school grade point averages [GPAs], Matrix Analogies test scores, and…

  13. Design requirements, criteria and methods for seismic qualification of CANDU power plants

    International Nuclear Information System (INIS)

    Singh, N.; Duff, C.G.

    1979-10-01

    This report describes the requirements and criteria for the seismic design and qualification of systems and equipment in CANDU nuclear power plants. Acceptable methods and techniques for seismic qualification of CANDU nuclear power plants to mitigate the effects or the consequences of earthquakes are also described. (auth)

  14. IMPORTANCE OF MULTIPLE CRITERIA FOR PRIORITY SETTING OF HIV/AIDS INTERVENTIONS.

    Science.gov (United States)

    Tromp, Noor; Prawiranegara, Rozar; Siregar, Adiatma; Sunjaya, Deni; Baltussen, Rob

    2015-01-01

    This study describes the views of various stakeholders on the importance of different criteria for priority setting of HIV/AIDS interventions in Indonesia. Based on a general list of criteria and a focus group discussion with stakeholders (n = 6), a list was developed of thirty-two criteria that play a role in priority setting in HIV/AIDS control in West-Java province. Criteria were categorized according to the World Health Organization's health system goals and building block frameworks. People living with HIV/AIDS (n = 49), healthcare workers (HCW) (n = 41), the general population (n = 43), and policy makers (n = 22) rated the importance of thirty-two criteria on a 5-point Likert-scale. Thereafter, respondents ranked the highest rated criteria to express more detailed preferences. Stakeholders valued the following criteria as most important for the priority setting of HIV/AIDS interventions: an intervention's impact on the HIV/AIDS epidemic, reduction of stigma, quality of care, effectiveness on individual level, and feasibility in terms of current capacity of the health system (i.e., HCW, product, information, and service requirements), financial sustainability, and acceptance by donors. Overall, stakeholders' preferences for the importance of criteria are similar. Our study design outlines an approach for other settings to identify which criteria are important for priority setting of health interventions. For Indonesia, these study results may be used in priority setting processes for HIV/AIDS control and may contribute to more transparent and systematic allocation of resources.

  15. Imaging and diagnostic criteria for multiple sclerosis: are we there yet?

    International Nuclear Information System (INIS)

    Josey, Lawrence; Curley, Michael; Mousavi, Foroogh Jafari; Taylor, Bruce V.; Lucas, Robyn; Coulthard, Alan

    2012-01-01

    Excluding post traumatic injury, Multiple Sclerosis (MS) is the most common disabling neurological disorder of young adults. Although the effect on mortality is limited, the association of a young demographic and significant morbidity combine to make MS a devastating disease. Since MS was given its first detailed description in 1868, diagnostic criteria continue to evolve. Recently, there has been an international commitment to combine both clinical and paraclinical tests to arrive at an earlier diagnosis. Widespread acceptance of the use of MRI in diagnosis, monitoring and research has made the role of the radiologist more critical than ever in this disease. The primary diagnostic criteria for MS are the International Panel criteria, commonly referred to as the McDonald criteria and it is essential that the radiology community is aware of the work preceding these criteria, so that they are understood in the correct context and the importance acknowledged. Literature review utilising key word search to obtain the historical and current context of magnetic resonance imaging in the diagnosis of MS. A succinct description of the evolution of criteria for the diagnosis of MS. Radiologists must recognise that there are specific diagnostic criteria for MS that continue to evolve as a result of new research, improved technology and clinical experience and it is crucial that these criteria be applied in daily practice. It should be evident that diagnostic imaging criteria for MS will be most effective when combined with standardised MRI protocols such as those published by the international Consortium of Multiple Sclerosis Centres.

  16. ACR appropriateness criteria blunt chest trauma.

    Science.gov (United States)

    Chung, Jonathan H; Cox, Christian W; Mohammed, Tan-Lucien H; Kirsch, Jacobo; Brown, Kathleen; Dyer, Debra Sue; Ginsburg, Mark E; Heitkamp, Darel E; Kanne, Jeffrey P; Kazerooni, Ella A; Ketai, Loren H; Ravenel, James G; Saleh, Anthony G; Shah, Rakesh D; Steiner, Robert M; Suh, Robert D

    2014-04-01

    Imaging is paramount in the setting of blunt trauma and is now the standard of care at any trauma center. Although anteroposterior radiography has inherent limitations, the ability to acquire a radiograph in the trauma bay with little interruption in clinical survey, monitoring, and treatment, as well as radiography's accepted role in screening for traumatic aortic injury, supports the routine use of chest radiography. Chest CT or CT angiography is the gold-standard routine imaging modality for detecting thoracic injuries caused by blunt trauma. There is disagreement on whether routine chest CT is necessary in all patients with histories of blunt trauma. Ultimately, the frequency and timing of CT chest imaging should be site specific and should depend on the local resources of the trauma center as well as patient status. Ultrasound may be beneficial in the detection of pneumothorax, hemothorax, and pericardial hemorrhage; transesophageal echocardiography is a first-line imaging tool in the setting of suspected cardiac injury. In the blunt trauma setting, MRI and nuclear medicine likely play no role in the acute setting, although these modalities may be helpful as problem-solving tools after initial assessment. The ACR Appropriateness Criteria are evidence-based guidelines for specific clinical conditions that are reviewed every 2 years by a multidisciplinary expert panel. The guideline development and review include an extensive analysis of current medical literature from peer-reviewed journals and the application of a well-established consensus methodology (modified Delphi) to rate the appropriateness of imaging and treatment procedures by the panel. In those instances in which evidence is lacking or not definitive, expert opinion may be used to recommend imaging or treatment. Copyright © 2014 American College of Radiology. Published by Elsevier Inc. All rights reserved.

  17. Criteria for onsite transfers of radioactive material

    International Nuclear Information System (INIS)

    Opperman, E.K.; Jackson, E.J.; Eggers, A.G.

    1992-01-01

    A general description of the requirements for making onsite transfers of radioactive material is provided in Chapter 2, along with the required sequencey of activities. Various criteria for package use are identified in Chapters 3-13. These criteria provide protection against undue radiation exposure. Package shielding, containment, and surface contamination requirements are established. Criteria for providing criticality safety are enumerated in Chapter 6. Criteria for providing hazards information are established in Chapter 13. A glossary is provided

  18. Design criteria for plutonium gloveboxes

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    The standard defines criteria for the design of glovebox systems to be used for the handling of plutonium in any form or isotopic composition or when mixed with other elements or compounds. The glovebox system is a series of physical barriers provided with glove ports and gloves, through which process and maintenance operations may be performed, together with an operating ventilation system. The system minimizes the potential for release of radioactive material to the environment, protects operators from contamination, and mitigates the consequences of abnormal condiations. The standard covers confinement, construction, materials, windows, glove ports, gloves, equipment insertion and removal, lighting, ventilation, fire protection, criticality prevention, services and utilities, radiation shielding, waste systems, monitoring and alarm systems, safeguards, quality assurance, and decommissioning

  19. Enhanced seismic criteria for piping

    International Nuclear Information System (INIS)

    Touboul, F. . E-mail francoise.touboul@cea.fr; Blay, N.; Sollogoub, P.; Chapuliot, S.

    2006-01-01

    In situ or laboratory experiments have shown that piping systems exhibit satisfactory seismic behavior. Seismic motion is not severe enough to significantly damage piping systems unless large differential motions of anchorage are imposed. Nevertheless, present design criteria for piping are very severe and require a large number of supports, which creates overly rigid piping systems. CEA, in collaboration with EDF, FRAMATOME and IRSN, has launched a large R and D program on enhanced design methods which will be less severe, but still conservative, and compatible with defect justification during operation. This paper presents the background of the R and D work on this matter, and CEA proposed equations. Our approach is based on the difference between the real behavior (or the best estimated computed one) with the one supposed by codified methods. Codified criteria are applied on an elastically calculated behavior that can be significantly different from the real one: the effect of plasticity may be very meaningful, even with low incursion in the plastic domain. Moreover, and particularly in piping systems, the elastic follow-up effect affects stress distribution for both seismic and thermal loads. For seismic load, we have proposed to modify the elastic moment limitation, based on the interpretation of experimental results on piping systems. The methods have been validated on more industrial cases, and some of the consequences of the changes have been studied: modification of the drawings and of the number of supports, global displacements, forces in the supports, stability of potential defects, etc. The basic aim of the studies undertaken is to make a decision on the stress classification problem, one that is not limited to seismic induced stresses, and to propose simplified methods for its solution

  20. 10 CFR 905.36 - Marketing criteria.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Marketing criteria. 905.36 Section 905.36 Energy DEPARTMENT OF ENERGY ENERGY PLANNING AND MANAGEMENT PROGRAM Power Marketing Initiative § 905.36 Marketing criteria. Western shall retain applicable provisions of existing marketing criteria for projects where...