Single-mode amplification in Yb-doped rod-type photonic crystal fibers for high brilliance lasers

DEFF Research Database (Denmark)

Poli, F.; Lægsgaard, Jesper; Passaro, D.

2009-01-01

This paper presents the effect of a low refractive index ring in the Yb-doped rod-type photonic crystal fibre core on the guided mode propagation and analyzed through a spatial and spectral amplifier model. The ring provides a higher differential overlap between the fundamental mode (FM...... to identify a proper ring characteristic that is width, position and refractive index. Then rod-type PCF designs have been optimized with a full-vector modal solver based on the finite-element method. Then, the amplification properties of the Yb-doped rod-type PCFs have been investigated by assuming a forward...

Calcination of Rod-like Hydroxyapatite Nanocrystals with an Anti-sintering Agent Surrounding the Crystals

International Nuclear Information System (INIS)

Okada, M.; Furuzono, T.

2007-01-01

Sintering-free nanocrystals of calcined hydroxyapatite (HAp) having a rod-like morphology were fabricated by calcination at 800 deg. C for 1 h with an anti-sintering agent surrounding original HAp particles and the agent was subsequently removed after calcination. The original HAp particles having a rod-like morphology with a size ranging from 30 to 80 nm (short axis) and 300 to 500 nm (long axis) were prepared by wet chemical process, and poly(acrylic acid, calcium salt) (PAA-Ca) was used as the anti-sintering agent. In the case of calcination without additives, the mean size of HAp crystals dispersed in an ethanol medium increased by about 4 times and the specific surface area of the crystals exhibited a 25% decrease compared to those of the original HAp particles because of calcination-induced sintering among the crystals. On the other hand, the HAp crystals calcined with the anti-sintering agent, PAA-Ca, could be dispersed in an ethanol medium at the same size as the original particles, and they preserved the specific surface area after calcination. These results indicate that PAA-Ca and/or its thermally decomposed product, CaO, surrounded the HAp particles and protected them against calcination-induced sintering during calcination. The HAp crystals calcined with PAA-Ca showed high crystallinity, and no other calcium phosphate phases could be detected after washing with water

Crystallization and preliminary X-ray analysis of a C-terminal fragment of FlgJ, a putative flagellar rod cap protein from Salmonella

International Nuclear Information System (INIS)

Kikuchi, Yuki; Matsunami, Hideyuki; Yamane, Midori; Imada, Katsumi; Namba, Keiichi

2008-01-01

A C-terminal fragment of Salmonella FlgJ, FlgJ 120–316 , which has peptidoglycan-hydrolysing activity, has been overproduced, purified and crystallized and the crystals have been characterized by X-ray diffraction. The formation of the bacterial flagellar axial structure, including the filament, the hook and the rod, requires the attachment of a cap complex to the distal end of the growing structure. Because the rod penetrates the peptidoglycan (PG) layer, the rod cap complex is thought to have PG-hydrolyzing activity. FlgJ is a putative rod cap protein whose C-terminal region shows sequence similarity to known muramidases. In this study, FlgJ 120–316 , a C-terminal fragment of FlgJ which contains the muramidase region, was overproduced, purified and crystallized. Crystals were obtained by the sitting-drop vapour-diffusion technique using PEG 3350 as a crystallizing agent and belonged to the orthorhombic space group P2 1 2 1 2 1 , with unit-cell parameters a = 38.8, b = 43.9, c = 108.5 Å. Anomalous difference Patterson maps calculated from the diffraction data set of a selenomethionine-labelled crystal showed significant peaks in the Harker sections, indicating that the data were suitable for structure determination

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 8 AND 9 CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wilson, Michael L.

2001-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 8 and 9 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 4 AND 5 OF CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wright, Kenneth D.

1997-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 4 and 5 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 4 AND 5 OF CRYSTAL RIVER UNIT 3

Energy Technology Data Exchange (ETDEWEB)

Kenneth D. Wright

1997-07-30

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 4 and 5 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies.

Orientation dependence of deformation and penetration behavior of tungsten single crystal rods

International Nuclear Information System (INIS)

Bruchey, W.J. Jr.; Horwath, E.J.; Kingman, P.W.

1991-01-01

This paper reports on deformation and flow at a target/penetrator interface that occurs under conditions of high hydrostatic pressure and associated heat generation. To further elucidate the role of material structure in the penetration process, oriented single crystals of tungsten have been launched into steel targets and the residual penetrators recovered and analyzed. Both the penetration depth and the deformation characteristics were strongly influenced by the crystallographic orientation. Deformation modes for the left-angle 100 right-angle rod, which exhibited the best performance, appeared to involve considerable localized slip/cleavage and relatively less plastic working; the residual penetrator was extensively cracked and the eroded penetrator material was extruded in a smooth tube lined with an oriented array of discrete particle exhibiting cleavage fractures. Deformation appeared to be much less localized and to involve more extensive plastic working in the left-angle 011 right-angle rod, which exhibited the poorest penetration, while the left-angle 111 right-angle behaved in an intermediate fashion

CRC DEPLETION CALCULATIONS FOR THE NON-RODDED ASSEMBLIES IN BATCHES 1, 2, AND 3 OF CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wright, Kenneth D.

1997-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain non-rodded fuel assemblies from batches 1, 2, and 3 of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support development of the disposal criticality methodology. A non-rodded assembly is one which never contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) during its irradiation history. The objective of this analysis is to provide SAS2H generated isotopic compositions for each fuel assembly's depleted fuel and depleted burnable poison materials. These SAS2H generated isotopic compositions are acceptable for use in CRC benchmark reactivity calculations containing the various fuel assemblies

Super-broadband non-diffraction guiding modes in photonic crystals with elliptical rods

Energy Technology Data Exchange (ETDEWEB)

Liang, W Y; Wang, T B; Yin, C P; Dong, J W; Leng, F C; Wang, H Z, E-mail: stswhz@mail.sysu.edu.c [State Key Laboratory of Optoelectronic Materials and Technologies, Zhongshan (Sun Yat-Sen) University, Guangzhou 510275 (China)

2010-02-24

Non-diffraction guiding modes covering the full broad band of a photonic crystal with elliptical rods for TM mode are reported in this paper. All such modes can be used to effectively guide electromagnetic waves since they have near-zero group velocity components along the {Gamma}X' direction. In the fourth dispersion surface of the photonic crystal, the two wide flat regions spanning the first Brillouin zone possess unique properties: one dimension corresponds to a broad band, while the other corresponds to full incident angles of 0-90{sup 0}. These properties have many potential applications; as an example, here a broadband all-angle supercollimation with a bandwidth of 169 nm around 1550 nm is demonstrated. For the inverted structure of elliptical holes in a dielectric, similar results can be achieved over 140 nm around 1550 nm for TE mode.

CRC DEPLETION CALCULATIONS FOR THE RODDED ASSEMBLIES IN BATCHES 1, 2, 3, AND 1X OF CRYSTAL RIVER UNIT 3

Energy Technology Data Exchange (ETDEWEB)

Kenneth D. Wright

1997-09-03

The purpose of this design analysis is to document the SAS2H depletion calculations of certain rodded fuel assemblies from batches 1, 2, 3, and 1X of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A rodded assembly is one that contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) for some period of time during its irradiation history. The objective of this analysis is to provide SAS2H calculated isotopic compositions of depleted fuel and depleted burnable poison for each fuel assembly to be used in subsequent CRC reactivity calculations containing the fuel assemblies.

CRC DEPLETION CALCULATIONS FOR THE RODDED ASSEMBLIES IN BATCHES 1, 2, 3, AND 1X OF CRYSTAL RIVER UNIT 3

International Nuclear Information System (INIS)

Wright, Kenneth D.

1997-01-01

The purpose of this design analysis is to document the SAS2H depletion calculations of certain rodded fuel assemblies from batches 1, 2, 3, and 1X of the Crystal River Unit 3 pressurized water reactor (PWR) that are required for Commercial Reactor Critical (CRC) evaluations to support the development of the disposal criticality methodology. A rodded assembly is one that contains a control rod assembly (CRA) or an axial power shaping rod assembly (APSRA) for some period of time during its irradiation history. The objective of this analysis is to provide SAS2H calculated isotopic compositions of depleted fuel and depleted burnable poison for each fuel assembly to be used in subsequent CRC reactivity calculations containing the fuel assemblies

Transformation of amorphous calcium carbonate to rod-like single crystal calcite via "copying" collagen template.

Science.gov (United States)

Xue, Zhonghui; Hu, Binbin; Dai, Shuxi; Du, Zuliang

2015-10-01

Collagen Langmuir films were prepared by spreading the solution of collagen over deionized water, CaCl2 solution and Ca(HCO3)2 solution. Resultant collagen Langmuir monolayers were then compressed to a lateral pressure of 10 mN/m and held there for different duration, allowing the crystallization of CaCO3. The effect of crystallization time on the phase composition and microstructure of CaCO3 was investigated. It was found that amorphous calcium carbonate (ACC) was obtained at a crystallization time of 6 h. The amorphous CaCO3 was transformed to rod-like single crystal calcite crystals at an extended crystallization time of 12 h and 24 h, via "copying" the symmetry and dimensionalities of collagen fibers. Resultant calcite crystallites were well oriented along the longitudinal axis of collagen fibers. The ordered surface structure of collagen fibers and electrostatic interactions played key roles in tuning the oriented nucleation and growth of the calcite crystallites. The mineralized collagen possessing both desired mechanical properties of collagen fiber and good biocompatibility of calcium carbonate may be assembled into an ideal biomaterial for bone implants. Copyright © 2015. Published by Elsevier B.V.

Distribution of Al and in impurities along homogeneous Ge-Si crystals grown by the Czochralski method using Si feeding rod

Science.gov (United States)

Kyazimova, V. K.; Alekperov, A. I.; Zakhrabekova, Z. M.; Azhdarov, G. Kh.

2014-05-01

A distribution of Al and In impurities in Ge1 - x Si x crystals (0 ≤ x ≤ 0.3) grown by a modified Czochralski method (with continuous feeding of melt using a Si rod) have been studied experimentally and theoretically. Experimental Al and In concentrations along homogeneous crystals have been determined from Hall measurements. The problem of Al and In impurity distribution in homogeneous Ge-Si single crystals grown in the same way is solved within the Pfann approximation. A set of dependences of Al and In concentrations on the crystal length obtained within this approximation demonstrates a good correspondence between the experimental and theoretical data.

Growth of Yb3+-doped Y2O3 single crystal rods by the micro-pulling-down method

International Nuclear Information System (INIS)

Mun, J.H.; Novoselov, A.; Yoshikawa, A.; Boulon, G.; Fukuda, T.

2005-01-01

The rare-earth sesquioxides (RE 2 O 3 , RE = Lu, Y and Sc) are very promising host crystals for advanced laser diode (LD)-pumped Yb 3+ -doped solid-state lasers due to unusual combination, almost unique of favourable structural, thermal and spectroscopic properties which are described. In spite of these favourable properties, the bulk single crystal growth technology for the rare-earth sesquioxides has not been established yet. The extremely high melting temperature at around 2400 deg. C has prevented it. However, we shall show that yttrium oxide crystals (Yb x Y 1-x ) 2 O 3 , x = 0.0, 0.005, 0.05, 0.08 and 0.15 of cylindrical shape as laser rods with 4.2 mm in diameter and 15-20 mm in length have been grown from rhenium crucibles by the micro-pulling-down method. The crystal quality characterisation of undoped Y 2 O 3 crystal was determined using X-ray rocking curve (XRC) analysis. Yb were homogeneously distributed in Y 2 O 3 host crystal

Urea controlled hydrothermal synthesis of ammonium aluminum carbonate hydroxide rods

Science.gov (United States)

Wang, Fang; Zhu, Jianfeng; Liu, Hui

2018-03-01

In this study, ammonium aluminum carbonate hydroxide (AACH) rods were controllably prepared using the hydrothermal method by manipulating the amount of urea in the reaction system. The experimental results showed that AACH in rod shape was able to be gradually transformed from γ-AlOOH in cluster shape during the molar ratios of urea to Al in the reactants were ranged from 8 to 10, and the yield of AACH has increased accordingly. When the molar ratio of urea to Al reaches 11, pure AACH rods with a diameter of 500 nm and a length of 10 μm approximately was able to be produced. Due to the slow decomposition of urea during the hydrothermal reaction, the nucleation and growth of AACH crystal proceed step by step. Therefore, the crystal can fully grow on each crystal plane and eventually produce a highly crystalline rod-shaped product. The role of urea in controlling the morphology and yield of AACH was also discussed in this paper systematically.

Preparation of rod-like β-Si3N4 single crystal particles

International Nuclear Information System (INIS)

Hirao, K.; Tsuge, A.; Brito, M.E.; Kanzaki, S.

1994-01-01

The use of β-Si 3 N 4 particles as a seed material has been demonstrated to be effective for development of a self-reinforcing microstructure in sintered silicon nitride ceramics. We have confirmed the seeding effect and arrived at a concept that seed particles should consist of rod-like single crystals free from defects and with a large diameter. The present work describes our attempts to produce such particles with a controlled morphology and in high amount. β-Si 3 N 4 particles with a diameter of 1μm and length of 5μm were obtained by heating a mixture of α-Si 3 N 4 , SiO 2 and Y 2 O 3 , followed by acid rinse treatments to remove residual glassy phase. (orig.)

A novel homozygous truncating GNAT1 mutation implicated in retinal degeneration.

Science.gov (United States)

Carrigan, Matthew; Duignan, Emma; Humphries, Pete; Palfi, Arpad; Kenna, Paul F; Farrar, G Jane

2016-04-01

The GNAT1 gene encodes the α subunit of the rod transducin protein, a key element in the rod phototransduction cascade. Variants in GNAT1 have been implicated in stationary night-blindness in the past, but unlike other proteins in the same pathway, it has not previously been implicated in retinitis pigmentosa. A panel of 182 retinopathy-associated genes was sequenced to locate disease-causing mutations in patients with inherited retinopathies. Sequencing revealed a novel homozygous truncating mutation in the GNAT1 gene in a patient with significant pigmentary disturbance and constriction of visual fields, a presentation consistent with retinitis pigmentosa. This is the first report of a patient homozygous for a complete loss-of-function GNAT1 mutation. The clinical data from this patient provide definitive evidence of retinitis pigmentosa with late onset in addition to the lifelong night-blindness that would be expected from a lack of transducin function. These data suggest that some truncating GNAT1 variants can indeed cause a recessive, mild, late-onset retinal degeneration in human beings rather than just stationary night-blindness as reported previously, with notable similarities to the phenotype of the Gnat1 knockout mouse. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Influence of Crucible Support Rod on the Growth Rate and Temperature Gradient in a Bridgman Growth of Tin Crystal

OpenAIRE

IMASHIMIZU, Yuji; MIURA, Koji; KAMATA, Masaki; WATANABE, Jiro

2003-01-01

Bridgman growth of tincrystal was carried out in a graphite crucible that was fixed on a quartz support rod or a copper one. The growth rate and axial temperature distribution were examined by recording the temperature variation with time at each of four prescribed positions in the solid-liquidsystem during solidification, l) Actual growth rate of crystal increased with progress of solidification while the furnace elevated at a constant rate, but the tendency was different depending on the ty...

Single-crystal SrTiO3 fiber grown by laser heated pedestal growth method: influence of ceramic feed rod preparation in fiber quality

Directory of Open Access Journals (Sweden)

D. Reyes Ardila

1998-10-01

Full Text Available The rapidly spreading use of optical fiber as a transmission medium has created an interest in fiber-compatible optical devices and methods for growing them, such as the Laser Heated Pedestal Growth (LHPG. This paper reports on the influence of the ceramic feed rod treatment on fiber quality and optimization of ceramic pedestal processing that allows improvements to be made on the final quality in a simple manner. Using the LHPG technique, transparent crack-free colorless single crystal fibers of SrTiO3 (0.50 mm in diameter and 30-40 mm in length were grown directly from green-body feed rods, without using external oxygen atmosphere.

Design of LD in-band direct-pumping side surface polished micro-rod Nd:YVO4 laser

International Nuclear Information System (INIS)

Zhang Wen-Qi; Wang Fei; Liu Qiang; Gong Ma-Li

2016-01-01

To diminish the thermal load, two ways, that is, in-band direct pumping and micro-rod crystal, could be adopted at the same time. The efficiency of LD in-band direct-pumping side surface polished micro-rod Nd:YVO 4 laser is numerically analyzed. By optimizing parameters such as crystal length, laser mode radius, pump beam radius, doping concentration and crystal cross-section size, the overall efficiency can reach over 50%. It is found that with micro-rod crystal implemented in the laser oscillator, high overall efficiency LD in-band direct-pumping Nd:YVO 4 laser could be realized. High efficiency combined with low thermal load makes this laser an outstanding scheme for building high-power Nd:YVO 4 lasers. (paper)

Photonic crystal rod fibers: Understanding a new class of active optical waveguides

DEFF Research Database (Denmark)

Laurila, Marko

core modes and the cladding band as the underlying mechanics to ensure SM operation of the new rod fiber design (85 μm core diameter), which was developed during this thesis work. The second focus of this work is the study of the new ytterbiumdoped rod fiber design under active operation. Performance...... of the rod fiber is evaluated in high power laser and laser amplifier configurations. The high power rod amplifier setup including the seed source is developed and characterized. Results obtained from the rod fiber showed simultaneously SM, near diffraction limited output beam quality with high average power...... and pulse energy generation using both laser and laser amplifier configurations. Modal instabilities (MIs) in high power fiber amplifiers are discussed, and a memory effect of the MI threshold level together with a recovery method and evidence of improved performance while suppressing MIs are reported...

Thermal Stress Analysis of a Continuous and Pulsed End-Pumped Nd:YAG Rod Crystal Using Non-Classic Conduction Heat Transfer Theory

Science.gov (United States)

Mojahedi, Mahdi; Shekoohinejad, Hamidreza

2018-02-01

In this paper, temperature distribution in the continuous and pulsed end-pumped Nd:YAG rod crystal is determined using nonclassical and classical heat conduction theories. In order to find the temperature distribution in crystal, heat transfer differential equations of crystal with consideration of boundary conditions are derived based on non-Fourier's model and temperature distribution of the crystal is achieved by an analytical method. Then, by transferring non-Fourier differential equations to matrix equations, using finite element method, temperature and stress of every point of crystal are calculated in the time domain. According to the results, a comparison between classical and nonclassical theories is represented to investigate rupture power values. In continuous end pumping with equal input powers, non-Fourier theory predicts greater temperature and stress compared to Fourier theory. It also shows that with an increase in relaxation time, crystal rupture power decreases. Despite of these results, in single rectangular pulsed end-pumping condition, with an equal input power, Fourier theory indicates higher temperature and stress rather than non-Fourier theory. It is also observed that, when the relaxation time increases, maximum amounts of temperature and stress decrease.

A Post-Truncation Parameterization of Truncated Normal Technical Inefficiency

OpenAIRE

Christine Amsler; Peter Schmidt; Wen-Jen Tsay

2013-01-01

In this paper we consider a stochastic frontier model in which the distribution of technical inefficiency is truncated normal. In standard notation, technical inefficiency u is distributed as N^+ (μ,σ^2). This distribution is affected by some environmental variables z that may or may not affect the level of the frontier but that do affect the shortfall of output from the frontier. We will distinguish the pre-truncation mean (μ) and variance (σ^2) from the post-truncation mean μ_*=E(u) and var...

Equivalence of truncated count mixture distributions and mixtures of truncated count distributions.

Science.gov (United States)

Böhning, Dankmar; Kuhnert, Ronny

2006-12-01

This article is about modeling count data with zero truncation. A parametric count density family is considered. The truncated mixture of densities from this family is different from the mixture of truncated densities from the same family. Whereas the former model is more natural to formulate and to interpret, the latter model is theoretically easier to treat. It is shown that for any mixing distribution leading to a truncated mixture, a (usually different) mixing distribution can be found so that the associated mixture of truncated densities equals the truncated mixture, and vice versa. This implies that the likelihood surfaces for both situations agree, and in this sense both models are equivalent. Zero-truncated count data models are used frequently in the capture-recapture setting to estimate population size, and it can be shown that the two Horvitz-Thompson estimators, associated with the two models, agree. In particular, it is possible to achieve strong results for mixtures of truncated Poisson densities, including reliable, global construction of the unique NPMLE (nonparametric maximum likelihood estimator) of the mixing distribution, implying a unique estimator for the population size. The benefit of these results lies in the fact that it is valid to work with the mixture of truncated count densities, which is less appealing for the practitioner but theoretically easier. Mixtures of truncated count densities form a convex linear model, for which a developed theory exists, including global maximum likelihood theory as well as algorithmic approaches. Once the problem has been solved in this class, it might readily be transformed back to the original problem by means of an explicitly given mapping. Applications of these ideas are given, particularly in the case of the truncated Poisson family.

How Truncating Are 'Truncating Languages'? Evidence from Russian and German.

Science.gov (United States)

Rathcke, Tamara V

Russian and German have pr eviously been described as 'truncating', or cutting off target frequencies of the phrase-final pitch trajectories when the time available for voicing is compromised. However, supporting evidence is rare and limited to only a few pitch categories. This paper reports a production study conducted to document pitch adjustments to linguistic materials, in which the amount of voicing available for the realization of a pitch pattern varies from relatively long to extremely short. Productions of nuclear H+L*, H* and L*+H pitch accents followed by a low boundary tone were investigated in the two languages. The results of the study show that speakers of both 'truncating languages' do not utilize truncation exclusively when accommodating to different segmental environments. On the contrary, they employ several strategies - among them is truncation but also compression and temporal re-alignment - to produce the target pitch categories under increasing time pressure. Given that speakers can systematically apply all three adjustment strategies to produce some pitch patterns (H* L% in German and Russian) while not using truncation in others (H+L* L% particularly in Russian), we question the effectiveness of the typological classification of these two languages as 'truncating'. Moreover, the phonetic detail of truncation varies considerably, both across and within the two languages, indicating that truncation cannot be easily modeled as a unified phenomenon. The results further suggest that the phrase-final pitch adjustments are sensitive to the phonological composition of the tonal string and the status of a particular tonal event (associated vs. boundary tone), and do not apply to falling vs. rising pitch contours across the board, as previously put forward for German. Implications for the intonational phonology and prosodic typology are addressed in the discussion. © 2017 S. Karger AG, Basel.

Mechanical reliability of falling systems. Case of control rods of nuclear reactors

International Nuclear Information System (INIS)

Rezkallah, B.

1991-05-01

After having briefly recalled the main principles adopted for nuclear reactor safety (barrier based method, emergency stop system, emergency cooling system) and how control rod operation anomalies are described, this research thesis first gives an overview of knowledge in the field of reliability (principles, qualitative and quantitative methods, failure trees, performance function, shock modelling and mode analysis). Then, the author presents the modelling of the drop and rotation of a control rod. The computation technique is the modal synthesis. The author highlights the influence of physical (friction, initial conditions) and numerical (modal truncation) parameters. He reports a probabilistic analysis of the problem and proposes a stochastic model for the different shock forces (notably friction). He compares the results with those obtained with the DEMT software. The last part reports the investigation of a rare case: the jamming or untimely stop of the control rod device

Preparation of HfC single crystals by a floating zone technique

International Nuclear Information System (INIS)

Otani, S.; Tanaka, T.

1981-01-01

HfC single crystals have been prepared using a floating zone technique by controlling the compositions of the initial molten zone and the feed rod. The obtained crystal rods were 6 cm long and 0.9 cm in diameter. The various parts of the crystal rods have nearly constant compositions (C/Hf(ZR) = 0.956-0.977), and do not contain any free carbon. The impurities in the crystal, evaporation product, and starting material were examined by fluorescence X-ray spectroscopy. The refining effect due to evaporation was discussed. (orig.)

Bacterial actin MreB assembles in complex with cell shape protein RodZ.

Science.gov (United States)

van den Ent, Fusinita; Johnson, Christopher M; Persons, Logan; de Boer, Piet; Löwe, Jan

2010-03-17

Bacterial actin homologue MreB is required for cell shape maintenance in most non-spherical bacteria, where it assembles into helical structures just underneath the cytoplasmic membrane. Proper assembly of the actin cytoskeleton requires RodZ, a conserved, bitopic membrane protein that colocalises to MreB and is essential for cell shape determination. Here, we present the first crystal structure of bacterial actin engaged with a natural partner and provide a clear functional significance of the interaction. We show that the cytoplasmic helix-turn-helix motif of Thermotoga maritima RodZ directly interacts with monomeric as well as filamentous MreB and present the crystal structure of the complex. In vitro and in vivo analyses of mutant T. maritima and Escherichia coli RodZ validate the structure and reveal the importance of the MreB-RodZ interaction in the ability of cells to propagate as rods. Furthermore, the results elucidate how the bacterial actin cytoskeleton might be anchored to the membrane to help constrain peptidoglycan synthesis in the periplasm.

Analysis of the β→α variant selection in a Zy-4 rod by means of specific crystal orientation maps

International Nuclear Information System (INIS)

Gey, N.; Humbert, M.; Gautier, E.; Bechade, J.L.

2002-01-01

A specific analysis of the α inherited crystal orientation map (COM) is proposed to study the β→α texture inheritance of a Zy-4 rod. In particular, it is shown that the α colonies inherited from each parent grain can systematically be identified on the α Map by considering the misorientations between pixels. Once identified, the orientations of these colonies are used to calculate the orientation of their common β grain. Finally, the orientation data of the parent phase can also be displayed as a COM. The β COM shows that at high temperature, the β grains were mainly oriented around the left angle 111 right angle //AD fibre. Moreover, the analysis of the parent and the inherited COM, makes clear that each β grain has preferentially transformed into different variants belonging each to the left angle 11.0 right angle //AD fibre. This variant selection is responsible for the sharp α texture of the Zy-4 rod after a treatment in the β field. (orig.)

R Programs for Truncated Distributions

Directory of Open Access Journals (Sweden)

Saralees Nadarajah

2006-08-01

Full Text Available Truncated distributions arise naturally in many practical situations. In this note, we provide programs for computing six quantities of interest (probability density function, mean, variance, cumulative distribution function, quantile function and random numbers for any truncated distribution: whether it is left truncated, right truncated or doubly truncated. The programs are written in R: a freely downloadable statistical software.

Chitin Fiber and Chitosan 3D Composite Rods

International Nuclear Information System (INIS)

Wang, Z.; Hu, Q.; Cai, L.

2010-01-01

Chitin fiber (CHF) and chitosan (CS) 3D composite rods with layer-by-layer structure were constructed by in situ precipitation method. CHF could not be dissolved in acetic acid aqueous solution, but CS could be dissolved due to the different deacetylation degree (D.D) between CHF and CS. CHF with undulate surfaces could be observed using SEM to demonstrate that the sufficiently rough surfaces and edges of the fiber could enhance the mechanical combining stress between fiber and matrix. XRD indicated that the crystallinity of CHF/CS composites decreased and CS crystal plane d-spacing of CHF/CS composites became larger than that of pure CS rod. TG analysis showed that mixing a little amount of CHF could enhance thermal stability of CS rod, but when the content of CHF was higher than the optimum amount, its thermal stability decreased. When 0.5% CHF was added into CS matrix, the bending strength and bending modulus of the composite rods arrived at 114.2 MPa and 5.2 GPa, respectively, increased by 23.6% and 26.8% compared with pure CS rods, indicating that CHF/CS composite rods could be a better candidate for bone fracture internal fixation.

Chitin Fiber and Chitosan 3D Composite Rods

Directory of Open Access Journals (Sweden)

Zhengke Wang

2010-01-01

Full Text Available Chitin fiber (CHF and chitosan (CS 3D composite rods with layer-by-layer structure were constructed by in situ precipitation method. CHF could not be dissolved in acetic acid aqueous solution, but CS could be dissolved due to the different deacetylation degree (D.D between CHF and CS. CHF with undulate surfaces could be observed using SEM to demonstrate that the sufficiently rough surfaces and edges of the fiber could enhance the mechanical combining stress between fiber and matrix. XRD indicated that the crystallinity of CHF/CS composites decreased and CS crystal plane d-spacing of CHF/CS composites became larger than that of pure CS rod. TG analysis showed that mixing a little amount of CHF could enhance thermal stability of CS rod, but when the content of CHF was higher than the optimum amount, its thermal stability decreased. When 0.5% CHF was added into CS matrix, the bending strength and bending modulus of the composite rods arrived at 114.2 MPa and 5.2 GPa, respectively, increased by 23.6% and 26.8% compared with pure CS rods, indicating that CHF/CS composite rods could be a better candidate for bone fracture internal fixation.

Zero-truncated negative binomial - Erlang distribution

Science.gov (United States)

Bodhisuwan, Winai; Pudprommarat, Chookait; Bodhisuwan, Rujira; Saothayanun, Luckhana

2017-11-01

The zero-truncated negative binomial-Erlang distribution is introduced. It is developed from negative binomial-Erlang distribution. In this work, the probability mass function is derived and some properties are included. The parameters of the zero-truncated negative binomial-Erlang distribution are estimated by using the maximum likelihood estimation. Finally, the proposed distribution is applied to real data, the number of methamphetamine in the Bangkok, Thailand. Based on the results, it shows that the zero-truncated negative binomial-Erlang distribution provided a better fit than the zero-truncated Poisson, zero-truncated negative binomial, zero-truncated generalized negative-binomial and zero-truncated Poisson-Lindley distributions for this data.

Angular truncation errors in integrating nephelometry

International Nuclear Information System (INIS)

Moosmueller, Hans; Arnott, W. Patrick

2003-01-01

Ideal integrating nephelometers integrate light scattered by particles over all directions. However, real nephelometers truncate light scattered in near-forward and near-backward directions below a certain truncation angle (typically 7 deg. ). This results in truncation errors, with the forward truncation error becoming important for large particles. Truncation errors are commonly calculated using Mie theory, which offers little physical insight and no generalization to nonspherical particles. We show that large particle forward truncation errors can be calculated and understood using geometric optics and diffraction theory. For small truncation angles (i.e., <10 deg. ) as typical for modern nephelometers, diffraction theory by itself is sufficient. Forward truncation errors are, by nearly a factor of 2, larger for absorbing particles than for nonabsorbing particles because for large absorbing particles most of the scattered light is due to diffraction as transmission is suppressed. Nephelometers calibration procedures are also discussed as they influence the effective truncation error

The evidence for synthesis of truncated triangular silver nanoplates in the presence of CTAB

International Nuclear Information System (INIS)

He Xin; Zhao Xiujian; Chen Yunxia; Feng Jinyang

2008-01-01

Truncated triangular silver nanoplates were prepared by a solution-phase approach, which involved the seed-mediated growth of silver nanoparticles in the presence of cetyltrimethylammonium bromide (CTAB) at 40 deg. C. The result of X-ray diffraction indicates that the as-prepared nanoparticles are made of pure face centered cubic silver. Transmission electron microscopy and atomic force microscopy studies show that the truncated triangular silver nanoplates, with edge lengths of 50 ± 5 nm and thicknesses of 27 ± 3 nm, are oriented differently on substrates of a copper grid and a fresh mica flake. The corners of these nanoplates are round. The selected area electron diffraction analysis reveals that the silver nanoplates are single crystals with an atomically flat surface. We determine the holistic morphology of truncated triangular silver nanoplates through the above measurements with the aid of computer-aided 3D perspective images

In-Situ Growth and Characterization of Indium Tin Oxide Nanocrystal Rods

Directory of Open Access Journals (Sweden)

Yan Shen

2017-11-01

Full Text Available Indium tin oxide (ITO nanocrystal rods were synthesized in-situ by a vapor-liquid-solid (VLS method and electron beam evaporation technique. When the electron-beam gun bombarded indium oxide (In2O3 and tin oxide (SnO2 mixed sources, indium and tin droplets appeared and acted as catalysts. The nanocrystal rods were in-situ grown on the basis of the metal catalyst point. The nanorods have a single crystal structure. Its structure was confirmed by X-ray diffraction (XRD and transmission electron microscopy (TEM. The surface morphology was analyzed by scanning electron microscopy (SEM. During the evaporation, a chemical process was happened and an In2O3 and SnO2 solid solution was formed. The percentage of doped tin oxide was calculated by Vegard’s law to be 3.18%, which was in agreement with the mixture ratio of the experimental data. The single crystal rod had good semiconductor switch property and its threshold voltage of single rod was approximately 2.5 V which can be used as a micro switch device. The transmission rate of crystalline nanorods ITO film was over 90% in visible band and it was up to 95% in the blue green band as a result of the oxygen vacancy recombination luminescence.

Chiral domain formation from the mixture of achiral rod-like liquid crystal and tri boomerang-shaped molecule

Science.gov (United States)

Lee, Ji-Hoon; Yoon, Tae-Hoon

2013-08-01

Spontaneous formation of chiral domains such as a helical filament and a bent-broom texture was observed from the mixture of a rod-like liquid crystal octylcyano-biphenyl (8CB) and a tri boomerang-shaped 2,4,6-triphenoxy-1,3,5-triazine (triphenoxy) molecule. Although the constituent molecules were achiral, their mixture showed the chiral domains with the equal fraction of the opposite handedness. No tilt of 8CB molecules in the smectic layer was observed, implying the chirality is not due to the polar packing and tilt of the molecules. In addition, the splay and bend elastic constant of 8CB was decreased after doping triphenoxy. A structural conformation of triphenoxy and an orientational coupling between 8CB and triphenoxy are considered to be related to the chiral domain formation.

Electromagnetic methods for measuring materials properties of cylindrical rods and array probes for rapid flaw inspection

Energy Technology Data Exchange (ETDEWEB)

Sun, Haiyan [Iowa State Univ., Ames, IA (United States)

2005-01-01

The case-hardening process modifies the near-surface permeability and conductivity of steel, as can be observed through changes in alternating current potential drop (ACPD) along a rod. In order to evaluate case depth of case hardened steel rods, analytical expressions are derived for the alternating current potential drop on the surface of a homogeneous rod, a two-layered and a three-layered rod. The case-hardened rod is first modeled by a two-layer rod that has a homogeneous substrate with a single, uniformly thick, homogeneous surface layer, in which the conductivity and permeability values differ from those in the substrate. By fitting model results to multi-frequency ACPD experimental data, estimates of conductivity, permeability and case depth are found. Although the estimated case depth by the two-layer model is in reasonable agreement with the effective case depth from the hardness profile, it is consistently higher than the effective case depth. This led to the development of the three-layer model. It is anticipated that the new three-layered model will improve the results and thus makes the ACPD method a novel technique in nondestructive measurement of case depth. Another way to evaluate case depth of a case hardened steel rod is to use induction coils. Integral form solutions for an infinite rod encircled by a coaxial coil are well known, but for a finite length conductor, additional boundary conditions must be satisfied at the ends. In this work, calculations of eddy currents are performed for a two-layer conducting rod of finite length excited by a coaxial circular coil carrying an alternating current. The solution is found using the truncated region eigenfunction expansion (TREE) method. By truncating the solution region to a finite length in the axial direction, the magnetic vector potential can be expressed as a series expansion of orthogonal eigenfunctions instead of as a Fourier integral. Closed-form expressions are derived for the electromagnetic

Tuning topological phase transitions in hexagonal photonic lattices made of triangular rods

Science.gov (United States)

Chan, Hsun-Chi; Guo, Guang-Yu

2018-01-01

In this paper we study topological phases in a two-dimensional photonic crystal with broken time (T ) and parity (P ) symmetries by performing calculations of band structures, Berry curvatures, Chern numbers, edge states, and also numerical simulations of light propagation in the edge modes. Specifically, we consider a hexagonal lattice consisting of triangular gyromagnetic rods. Here the gyromagnetic material breaks T symmetry while the triangular rods break P symmetry. Interestingly, we find that the crystal could host quantum anomalous Hall (QAH) phases with different gap Chern numbers (Cg) including | Cg|>1 as well as quantum valley Hall (QVH) phases with contrasting valley Chern numbers (Cv), depending on the orientation of the triangular rods. Furthermore, phase transitions among these topological phases, such as from QAH to QVH and vice versa, can be engineered by a simple rotation of the rods. Our band theoretical analyses reveal that the Dirac nodes at the K and K' valleys in the momentum space are produced and protected by the mirror symmetry (my) instead of the P symmetry, and they become gapped when either T or my symmetry is broken, resulting in a QAH or QVH phase, respectively. Moreover, a high Chern number (Cg=-2 ) QAH phase is generated by gapping triply degenerate nodal points rather than pairs of Dirac points by breaking T symmetry. Our proposed photonic crystal thus provides a platform for investigating intriguing topological phenomena which may be challenging to realize in electronic systems, and also has promising potentials for device applications in photonics such as reflection-free one-way waveguides and topological photonic circuits.

Control rod

International Nuclear Information System (INIS)

Kawakami, Kazuo; Shimoshige, Takanori; Nishimura, Akira

1979-01-01

Purpose: A control rod has been developed, which provided a plurality of through-holes in the vicinity of the sheath fitting position, in order to flatten burn-up, of fuel rods in positions confronting a control rod. Thereby to facilitate the manufacture of the control rods and prevent fuel rod failures. Constitution: A plurality of through-holes are formed in the vicinity of the sheath fitting position of a central support rod to which a sheath for the control rod is fitted. These through-holes are arranged in the axial direction of the central support rod. Accordingly, burn-up of fuel rods confronting the control rods can be reduced by through-holes and fuel rod failures can be prevented. (Yoshino, Y.)

Dual curved photonic crystal ring resonator based channel drop filter using two-dimensional photonic crystal structure

Energy Technology Data Exchange (ETDEWEB)

Chhipa, Mayur Kumar, E-mail: mayurchhipa1@gmail.com [Deptt. of Electronics and Communication Engineering, Government Engineering College Ajmer Rajasthan INDIA (India); Dusad, Lalit Kumar [Rajasthan Technical University Kota, Rajasthan (India)

2016-05-06

In this paper channel drop filter (CDF) is designed using dual curved photonic crystal ring resonator (PCRR). The photonic band gap (PBG) is calculated by plane wave expansion (PWE) method and the photonic crystal (PhC) based on two dimensional (2D) square lattice periodic arrays of silicon (Si) rods in air structure have been investigated using finite difference time domain (FDTD) method. The number of rods in Z and X directions is 21 and 20 respectively with lattice constant 0.540 nm and rod radius r = 0.1 µm. The channel drop filter has been optimized for telecommunication wavelengths λ = 1.591 µm with refractive indices 3.533. In the designed structure further analysis is also done by changing whole rods refractive index and it has been observed that this filter may be used for filtering several other channels also. The designed structure is useful for CWDM systems. This device may serve as a key component in photonic integrated circuits. The device is ultra compact with the overall size around 123 µm{sup 2}.

Investigation of 2D photonic crystal structure based channel drop filter using quad shaped photonic crystal ring resonator for CWDM system

Energy Technology Data Exchange (ETDEWEB)

Chhipa, Mayur Kumar, E-mail: mayurchhipa1@gmail.com; Dusad, Lalit Kumar [Government Engineering College Ajmer, Rajasthan (India); Rajasthan Technical University, Kota, Rajasthan (India)

2016-05-06

In this paper, the design & performance of two dimensional (2-D) photonic crystal structure based channel drop filter is investigated using quad shaped photonic crystal ring resonator. In this paper, Photonic Crystal (PhC) based on square lattice periodic arrays of Gallium Indium Phosphide (GaInP) rods in air structure have been investigated using Finite Difference Time Domain (FDTD) method and photonic band gap is being calculated using Plane Wave Expansion (PWE) method. The PhC designs have been optimized for telecommunication wavelength λ= 1571 nm by varying the rods lattice constant. The number of rods in Z and X directions is 21 and 20, with lattice constant 0.540 nm it illustrates that the arrangement of Gallium Indium Phosphide (GaInP) rods in the structure which gives the overall size of the device around 11.4 µm × 10.8 µm. The designed filter gives good dropping efficiency using 3.298, refractive index. The designed structure is useful for CWDM systems. This device may serve as a key component in photonic integrated circuits. The device is ultra compact with the overall size around 123 µm{sup 2}.

Development of longer Nd:LGGG crystal for high power laser application

Science.gov (United States)

Yin, Yanru; Tian, Hanlin; Zhang, Jian; Mu, Wenxiang; Zhang, Baitao; Jia, Zhitai; He, Jingliang; Tao, Xutang

2017-11-01

In order to further improve the Nd3+:(LuxGd1-x)3Ga5O12 (Nd:LGGG) crystal performance in high power laser field, a long Nd:LGGG crystal with dimensions of Φ 23 × 112 mm3 has been grown successfully by the Czochralski (Cz) method for laser rod fabrication. Compared with the normal size LGGG crystals (like 30-50 mm in length), we overcame several difficulties in the growth of longer ones, including crystal cracking by a large longitudinal temperature gradient, spiral growth by a small radial temperature gradient, and growth instability and even constitutional super cooling by Ga2O3 volatilizing continuously. The doping concentrations of Nd3+ and Lu3+ in the as-grown crystal and the crystal optical quality have been measured. The performance of diode-side-pumped Nd:LGGG rod laser has been preliminarily tested for the first time, simply by replacing the Nd:YAG crystal rod inside a commercial laser module. Under an incident pump power of 160 W, the maximum continuous wave output power of 38 W has been obtained, corresponding to an optical-optical conversion efficiency of 23.8% and a slope efficiency of 40.8%, respectively.

Truncated Groebner fans and lattice ideals

OpenAIRE

Lauritzen, Niels

2005-01-01

We outline a generalization of the Groebner fan of a homogeneous ideal with maximal cells parametrizing truncated Groebner bases. This "truncated" Groebner fan is usually much smaller than the full Groebner fan and offers the natural framework for conversion between truncated Groebner bases. The generic Groebner walk generalizes naturally to this setting by using the Buchberger algorithm with truncation on facets. We specialize to the setting of lattice ideals. Here facets along the generic w...

Control rod

International Nuclear Information System (INIS)

Igarashi, Takao; Sugawara, Satoshi; Yoshimoto, Yuichiro; Saito, Shozo; Fukumoto, Takashi.

1987-01-01

Purpose: To reduce the weight and thereby obtain satisfactory operationability of control rods by combining absorbing nuclear chain type neutron absorbers and conventional type neutron absorbers in the axial direction of blades. Constitution: Neutron absorber rods and long life type neutron absorber rods are disposed in a tie rod and a sheath. The neutron absorber rod comprises a poison tube made of stainless steels and packed with B 4 C powder. The long life type neutron absorber rod is prepared by packing B-10 enriched boron carbide powder into a hafnium metal rod, hafnium pipe, europium and stainless made poison tube. Since the long life type absorber rod uses HF as the absorbing nuclear chain type neutron absorber, it absorbs neutrons to form new neutron absorbers to increase the nuclear life. (Yoshino, Y.)

Statistical estimation for truncated exponential families

CERN Document Server

Akahira, Masafumi

2017-01-01

This book presents new findings on nonregular statistical estimation. Unlike other books on this topic, its major emphasis is on helping readers understand the meaning and implications of both regularity and irregularity through a certain family of distributions. In particular, it focuses on a truncated exponential family of distributions with a natural parameter and truncation parameter as a typical nonregular family. This focus includes the (truncated) Pareto distribution, which is widely used in various fields such as finance, physics, hydrology, geology, astronomy, and other disciplines. The family is essential in that it links both regular and nonregular distributions, as it becomes a regular exponential family if the truncation parameter is known. The emphasis is on presenting new results on the maximum likelihood estimation of a natural parameter or truncation parameter if one of them is a nuisance parameter. In order to obtain more information on the truncation, the Bayesian approach is also considere...

NLO renormalization in the Hamiltonian truncation

Science.gov (United States)

Elias-Miró, Joan; Rychkov, Slava; Vitale, Lorenzo G.

2017-09-01

Hamiltonian truncation (also known as "truncated spectrum approach") is a numerical technique for solving strongly coupled quantum field theories, in which the full Hilbert space is truncated to a finite-dimensional low-energy subspace. The accuracy of the method is limited only by the available computational resources. The renormalization program improves the accuracy by carefully integrating out the high-energy states, instead of truncating them away. In this paper, we develop the most accurate ever variant of Hamiltonian Truncation, which implements renormalization at the cubic order in the interaction strength. The novel idea is to interpret the renormalization procedure as a result of integrating out exactly a certain class of high-energy "tail states." We demonstrate the power of the method with high-accuracy computations in the strongly coupled two-dimensional quartic scalar theory and benchmark it against other existing approaches. Our work will also be useful for the future goal of extending Hamiltonian truncation to higher spacetime dimensions.

Control rods

International Nuclear Information System (INIS)

Maruyama, Hiromi.

1984-01-01

Purpose: To realize effective utilization, cost reduction and weight reduction in neutron absorbing materials. Constitution: Residual amount of neutron absorbing material is averaged between the top end region and other regions of a control rod upon reaching to the control rod working life, by using a single kind of neutron absorbing material and increasing the amount of the neutron absorber material at the top end region of the control rod as compared with that in the other regions. Further, in a case of a control rod having control rod blades such as in a cross-like control rod, the amount of the neutron absorbing material is decreased in the middle portion than in the both end portions of the control rod blade along the transversal direction of the rod, so that the residual amount of the neutron absorbing material is balanced between the central region and both end regions upon reaching the working life of the control rod. (Yoshihara, H.)

Control rod calibration including the rod coupling effect

International Nuclear Information System (INIS)

Szilard, R.; Nelson, G.W.

1984-01-01

In a reactor containing more than one control rod, which includes all reactors licensed in the United States, there will be a 'coupling' or 'shadowing' of control rod flux at the location of a control rod as a result of the flux depression caused by another control rod. It was decided to investigate this phenomenon further, and eventually to put calibration table data or formulae in a small computer in the control room, so once could insert the positions of the three control rods and receive the excess reactivity without referring to separate tables. For this to be accomplished, a 'three control- rod reactivity function' would be used which would include the flux coupling between the rods. The function is design and measured data was fitted into it to determine the calibration constants. The input data for fitting the trial functions consisted of 254 data points, each consisting of the position of the reg, shim, and transient rods, and the total excess reactivity. (About 200 of these points were 'critical balance points', that is the rod positions for which reactor was critical, and the remainder were determined by positive period measurements.) Although this may be unrealistic from a physical viewpoint, the function derived gave a very accurate recalculation of the input data, and thus would faithfully give the excess reactivity for any possible combination of the locations of the three control rods. The next step, incorporation of the three-rod function into the minicomputer, will be pursued in the summer and fall of 1984

Stability of Slopes Reinforced with Truncated Piles

Directory of Open Access Journals (Sweden)

Shu-Wei Sun

2016-01-01

Full Text Available Piles are extensively used as a means of slope stabilization. A novel engineering technique of truncated piles that are unlike traditional piles is introduced in this paper. A simplified numerical method is proposed to analyze the stability of slopes stabilized with truncated piles based on the shear strength reduction method. The influential factors, which include pile diameter, pile spacing, depth of truncation, and existence of a weak layer, are systematically investigated from a practical point of view. The results show that an optimum ratio exists between the depth of truncation and the pile length above a slip surface, below which truncating behavior has no influence on the piled slope stability. This optimum ratio is bigger for slopes stabilized with more flexible piles and piles with larger spacing. Besides, truncated piles are more suitable for slopes with a thin weak layer than homogenous slopes. In practical engineering, the piles could be truncated reasonably while ensuring the reinforcement effect. The truncated part of piles can be filled with the surrounding soil and compacted to reduce costs by using fewer materials.

Biosynthesis and recovery of rod-shaped tellurium nanoparticles and their bactericidal activities

Energy Technology Data Exchange (ETDEWEB)

Zare, Bijan; Faramarzi, Mohammad Ali; Sepehrizadeh, Zargham [Department of Pharmaceutical Biotechnology and Biotechnology Research Center, Faculty of Pharmacy, Tehran University of Medical Sciences, P.O. Box 14155-6451 Tehran (Iran, Islamic Republic of); Shakibaie, Mojtaba [Department of Pharmacognosy and Biotechnology, School of Pharmacy, Pharmaceutics Research Center, Kerman University of Medical Sciences, P.O. Box 76175-493 Kerman (Iran, Islamic Republic of); Rezaie, Sassan [Department of Medical Biotechnology, School of Advanced Medical Technologies, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Shahverdi, Ahmad Reza, E-mail: shahverd@sina.tums.ac.ir [Department of Pharmaceutical Biotechnology and Biotechnology Research Center, Faculty of Pharmacy, Tehran University of Medical Sciences, P.O. Box 14155-6451 Tehran (Iran, Islamic Republic of)

2012-11-15

Highlights: ► Biosynthesis of rod shape tellurium nanoparticles with a hexagonal crystal structure. ► Extraction procedure for isolation of tellurium nanoparticles from Bacillus sp. BZ. ► Extracted tellurium nanoparticles have good bactericidal activity against some bacteria. -- Abstract: In this study, a tellurium-transforming Bacillus sp. BZ was isolated from the Caspian Sea in northern Iran. The isolate was identified by various tests and 16S rDNA analysis, and then used to prepare elemental tellurium nanoparticles. The isolate was subsequently used for the intracellular biosynthesis of elemental tellurium nanoparticles. The biogenic nanoparticles were released by liquid nitrogen and purified by an n-octyl alcohol water extraction system. The shape, size, and composition of the extracted nanoparticles were characterized. The transmission electron micrograph showed rod-shaped nanoparticles with dimensions of about 20 nm × 180 nm. The energy dispersive X-ray and X-ray diffraction spectra respectively demonstrated that the extracted nanoparticles consisted of only tellurium and have a hexagonal crystal structure. This is the first study to demonstrate a biological method for synthesizing rod-shaped elemental tellurium by a Bacillus sp., its extraction and its antibacterial activity against different clinical isolates.

Biosynthesis and recovery of rod-shaped tellurium nanoparticles and their bactericidal activities

International Nuclear Information System (INIS)

Zare, Bijan; Faramarzi, Mohammad Ali; Sepehrizadeh, Zargham; Shakibaie, Mojtaba; Rezaie, Sassan; Shahverdi, Ahmad Reza

2012-01-01

Highlights: ► Biosynthesis of rod shape tellurium nanoparticles with a hexagonal crystal structure. ► Extraction procedure for isolation of tellurium nanoparticles from Bacillus sp. BZ. ► Extracted tellurium nanoparticles have good bactericidal activity against some bacteria. -- Abstract: In this study, a tellurium-transforming Bacillus sp. BZ was isolated from the Caspian Sea in northern Iran. The isolate was identified by various tests and 16S rDNA analysis, and then used to prepare elemental tellurium nanoparticles. The isolate was subsequently used for the intracellular biosynthesis of elemental tellurium nanoparticles. The biogenic nanoparticles were released by liquid nitrogen and purified by an n-octyl alcohol water extraction system. The shape, size, and composition of the extracted nanoparticles were characterized. The transmission electron micrograph showed rod-shaped nanoparticles with dimensions of about 20 nm × 180 nm. The energy dispersive X-ray and X-ray diffraction spectra respectively demonstrated that the extracted nanoparticles consisted of only tellurium and have a hexagonal crystal structure. This is the first study to demonstrate a biological method for synthesizing rod-shaped elemental tellurium by a Bacillus sp., its extraction and its antibacterial activity against different clinical isolates.

Effects of supporting electrolyte on galvanic deposition of Cu2O crystals

International Nuclear Information System (INIS)

Wang Lida; Liu Guichang; Xue Dongfeng

2011-01-01

Highlights: → The effects of electrolyte on the galvanic deposition of Cu 2 O crystals have been investigated. → The chemical nature of supporting electrolyte plays important roles in the galvanic deposition of Cu 2 O crystals. → Cubic Cu 2 O crystals are formed in chloride electrolytes. → Truncated octahedral Cu 2 O crystals are produced in nitrate, sulfate and fluoride electrolytes. - Abstract: The effects of introduced supporting electrolyte on the galvanic deposition of Cu 2 O crystals have been investigated using scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), X-ray diffraction (XRD). The results show that the chemical nature of supporting electrolytes plays very important roles in the galvanic deposition of Cu 2 O crystals. The chloride stabilizes the (1 0 0) planes of Cu 2 O crystals, resulting in the formation of cubic crystals, while nitrate, sulfate and fluoride stabilize the (1 1 1) planes of Cu 2 O crystals, leading to the deposition of truncated octahedral and octahedral Cu 2 O crystals. It provides a facile way to control the morphology of galvanically obtained Cu 2 O crystals by indirectly adjusting the inorganic adsorption agents.

Adaptation of the delta-m and δ-fit truncation methods to vector radiative transfer: Effect of truncation on radiative transfer accuracy

International Nuclear Information System (INIS)

Sanghavi, Suniti; Stephens, Graeme

2015-01-01

In the presence of aerosol and/or clouds, the use of appropriate truncation methods becomes indispensable for accurate but cost-efficient radiative transfer computations. Truncation methods allow the reduction of the large number (usually several hundreds) of Fourier components associated with particulate scattering functions to a more manageable number, thereby making it possible to carry out radiative transfer computations with a modest number of streams. While several truncation methods have been discussed for scalar radiative transfer, few rigorous studies have been made of truncation methods for the vector case. Here, we formally derive the vector form of Wiscombe's delta-m truncation method. Two main sources of error associated with delta-m truncation are identified as the delta-separation error (DSE) and the phase-truncation error (PTE). The view angles most affected by truncation error occur in the vicinity of the direction of exact backscatter. This view geometry occurs commonly in satellite based remote sensing applications, and is hence of considerable importance. In order to deal with these errors, we adapt the δ-fit approach of Hu et al. (2000) [17] to vector radiative transfer. The resulting δBGE-fit is compared with the vectorized delta-m method. For truncation at l=25 of an original phase matrix consisting of over 300 Fourier components, the use of the δBGE-fit minimizes the error due to truncation at these view angles, while practically eliminating error at other angles. We also show how truncation errors have a distorting effect on hyperspectral absorption line shapes. The choice of the δBGE-fit method over delta-m truncation minimizes errors in absorption line depths, thus affording greater accuracy for sensitive retrievals such as those of XCO 2 from OCO-2 or GOSAT measurements. - Highlights: • Derives vector form for delta-m truncation method. • Adapts δ-fit truncation approach to vector RTE as δBGE-fit. • Compares truncation

Exact method for the simulation of Coulombic systems by spherically truncated, pairwise r-1 summation

International Nuclear Information System (INIS)

Wolf, D.; Keblinski, P.; Phillpot, S.R.; Eggebrecht, J.

1999-01-01

Based on a recent result showing that the net Coulomb potential in condensed ionic systems is rather short ranged, an exact and physically transparent method permitting the evaluation of the Coulomb potential by direct summation over the r -1 Coulomb pair potential is presented. The key observation is that the problems encountered in determining the Coulomb energy by pairwise, spherically truncated r -1 summation are a direct consequence of the fact that the system summed over is practically never neutral. A simple method is developed that achieves charge neutralization wherever the r -1 pair potential is truncated. This enables the extraction of the Coulomb energy, forces, and stresses from a spherically truncated, usually charged environment in a manner that is independent of the grouping of the pair terms. The close connection of our approach with the Ewald method is demonstrated and exploited, providing an efficient method for the simulation of even highly disordered ionic systems by direct, pairwise r -1 summation with spherical truncation at rather short range, i.e., a method which fully exploits the short-ranged nature of the interactions in ionic systems. The method is validated by simulations of crystals, liquids, and interfacial systems, such as free surfaces and grain boundaries. copyright 1999 American Institute of Physics

Multidimensional simulations of hydrides during fuel rod lifecycle

International Nuclear Information System (INIS)

Stafford, D.S.

2015-01-01

In light water reactor fuel rods, waterside corrosion of zirconium-alloy cladding introduces hydrogen into the cladding, where it is slightly soluble. When the solubility limit is reached, the hydrogen precipitates into crystals of zirconium hydride which decrease the ductility of the cladding and may lead to cladding failure during dry storage or transportation events. The distribution of the hydride phase and the orientation of the crystals depend on the history of the spatial temperature and stress profiles in the cladding. In this work, we have expanded the existing hydride modeling capability in the BISON fuel performance code with the goal of predicting both global and local effects on the radial, azimuthal and axial distribution of the hydride phase. We compare results from 1D simulations to published experimental data. We demonstrate the new capability by simulating in 2D a fuel rod throughout a lifecycle that includes irradiation, short-term storage in the spent fuel pool, drying, and interim storage in a dry cask. Using the 2D simulations, we present qualitative predictions of the effects of the inter-pellet gap and the drying conditions on the growth of a hydride rim. - Highlights: • We extend BISON fuel performance code to simulate lifecycle of fuel rods. • We model hydrogen evolution in cladding from reactor through dry storage. • We validate 1D simulations of hydrogen evolution against experiments. • We show results of 2D axisymmetric simulations predicting hydride formation. • We show how our model predicts formation of a hydride rim in the cladding.

Computing correct truncated excited state wavefunctions

Science.gov (United States)

Bacalis, N. C.; Xiong, Z.; Zang, J.; Karaoulanis, D.

2016-12-01

We demonstrate that, if a wave function's truncated expansion is small, then the standard excited states computational method, of optimizing one "root" of a secular equation, may lead to an incorrect wave function - despite the correct energy according to the theorem of Hylleraas, Undheim and McDonald - whereas our proposed method [J. Comput. Meth. Sci. Eng. 8, 277 (2008)] (independent of orthogonality to lower lying approximants) leads to correct reliable small truncated wave functions. The demonstration is done in He excited states, using truncated series expansions in Hylleraas coordinates, as well as standard configuration-interaction truncated expansions.

The polyproline site in hinge 2 influences the functional capacity of truncated dystrophins.

Directory of Open Access Journals (Sweden)

Glen B Banks

2010-05-01

Full Text Available Mutations in dystrophin can lead to Duchenne muscular dystrophy or the more mild form of the disease, Becker muscular dystrophy. The hinge 3 region in the rod domain of dystrophin is particularly prone to deletion mutations. In-frame deletions of hinge 3 are predicted to lead to BMD, however the severity of disease can vary considerably. Here we performed extensive structure-function analyses of truncated dystrophins with modified hinges and spectrin-like repeats in mdx mice. We found that the polyproline site in hinge 2 profoundly influences the functional capacity of a microdystrophin(DeltaR4-R23/DeltaCT with a large deletion in the hinge 3 region. Inclusion of polyproline in microdystrophin(DeltaR4-R23/DeltaCT led to small myofibers (12% smaller than wild-type, Achilles myotendinous disruption, ringed fibers, and aberrant neuromuscular junctions in the mdx gastrocnemius muscles. Replacing hinge 2 of microdystrophin(DeltaR4-R23/DeltaCT with hinge 3 significantly improved the functional capacity to prevent muscle degeneration, increase muscle fiber area, and maintain the junctions. We conclude that the rigid alpha-helical structure of the polyproline site significantly impairs the functional capacity of truncated dystrophins to maintain appropriate connections between the cytoskeleton and extracellular matrix.

X-ray diffraction study of a semiconductor/electrolyte interface: n-GaAs(001)/H₂SO₄(:Cu)

DEFF Research Database (Denmark)

Zegenhagen, J.; Kazimirov, A.; Scherb, G.

1996-01-01

We used X-ray diffraction to investigate the n-GaAs(001)/0.5M H2SO4 interface in-situ under potential control in a three-electrode, thin-layer electrochemical cell. The intensity of crystal truncation rods as a function of the electrode potential was recorded. A pronounced increase in surface rou...

Control rod drives

International Nuclear Information System (INIS)

Nakamura, Akira.

1984-01-01

Purpose: To enable to monitor the coupling state between a control rod and a control rod drive. Constitution: After the completion of a control rod withdrawal, a coolant pressure is applied to a control rod drive being adjusted so as to raise only the control rod drive and, in a case where the coupling between the control rod drive and the control rod is detached, the former is elevated till it contacts the control rod and then stopped. The actual stopping position is detected by an actual position detection circuit and compared with a predetermined position stored in a predetermined position detection circuit. If both of the positions are not aligned with each other, it is judged by a judging circuit that the control rod and the control rod drives are not combined. (Sekiya, K.)

Mixtures of truncated basis functions

DEFF Research Database (Denmark)

Langseth, Helge; Nielsen, Thomas Dyhre; Rumí, Rafael

2012-01-01

In this paper we propose a framework, called mixtures of truncated basis functions (MoTBFs), for representing general hybrid Bayesian networks. The proposed framework generalizes both the mixture of truncated exponentials (MTEs) framework and the mixture of polynomials (MoPs) framework. Similar t...

Applications of Fast Truncated Multiplication in Cryptography

Directory of Open Access Journals (Sweden)

Laszlo Hars

2006-12-01

Full Text Available Truncated multiplications compute truncated products, contiguous subsequences of the digits of integer products. For an n-digit multiplication algorithm of time complexity O(nα, with 1<α≤2, there is a truncated multiplication algorithm, which is constant times faster when computing a short enough truncated product. Applying these fast truncated multiplications, several cryptographic long integer arithmetic algorithms are improved, including integer reciprocals, divisions, Barrett and Montgomery multiplications, 2n-digit modular multiplication on hardware for n-digit half products. For example, Montgomery multiplication is performed in 2.6 Karatsuba multiplication time.

Control rod assembly

International Nuclear Information System (INIS)

Takahashi, Akio.

1982-01-01

Purpose: To enable reliable insertion and drops of control rods, as well as insure a sufficient flow rate of coolants flowing through the control rods for attaining satisfactory cooling thereof to enable relexation of thermal stress resulted to rectifying mechanisms or the likes. Constitution: To the outer circumference of a control rod contained vertically movably within a control rod guide tube, resistive members are retractably provided in such a way as to project to close the gap between outer circumference of the control rod and the inner surface of the control rod guide tube upon engagement of a gripper of control rod drives, and retract upon release of the engagement of the gripper. Thus, since the resistive members project to provide a greater resistance to the coolants flowing between them and the control rod guide tube in the normal operation where the gripper is engaged to drive the control rod by the control rod drives, a major part of the coolant flowing into the control rod guide tube flows into the control rod. This enables to cool the control rod effectively and make the temperature distribution uniform for the coolant flowing from the upper end of the control rod guide tube to thereby attain the relaxation of the thermal stress resulted in the rectifying mechanisms or the likes. (Moriyama, K.)

An in-situ X-ray diffraction study on the electrochemical formation of PtZn alloys on Pt(1 1 1) single crystal electrode

Energy Technology Data Exchange (ETDEWEB)

Drnec, J., E-mail: drnec@esrf.fr [ESRF, Grenoble (France); Bizzotto, D. [Department of Chemistry, AMPEL, University of British Columbia, Vancouver, BC (Canada); Carlà, F. [ESRF, Grenoble (France); Fiala, R. [Charles University, Faculty of Mathematics and Physics, Prague (Czech Republic); Sode, A. [Ruhr-Universität Bochum, Bochum (Germany); Balmes, O.; Detlefs, B.; Dufrane, T. [ESRF, Grenoble (France); Felici, R., E-mail: felici@esrf.fr [ESRF, Grenoble (France)

2015-11-01

Highlights: • PtZn electrochemical alloying is observed on single crystal Pt electrodes. • In-situ X-ray characterization during alloy formation and dissolution is provided. • Structural model of the surface during alloying and dissolution is discussed. • X-ray based techniques can be used in in-operando studies of bimetallic fuel cell catalysts. - Abstract: The electrochemical formation and dissolution of the oxygen reduction reaction (ORR) PtZn catalyst on Pt(1 1 1) surface is followed by in-situ X-ray diffraction (XRD) and X-ray reflectivity (XRR) measurements. When the crystalline Pt surface is polarized to sufficiently negative potential values, with respect to an Ag/AgCl|KCl reference electrode, the electrodeposited zinc atoms diffuse into the bulk and characteristic features are observed in the X-ray patterns. The surface structure and composition during deposition and dissolution is determined from analysis of XRR curves and measurements of crystal truncation rods. Thin Zn-rich surface layer is present during the alloy formation while a Zn-depleted layer forms during dissolution.

Device for coupling a control rod and control rod drive

International Nuclear Information System (INIS)

Nishioka, Kazuya.

1975-01-01

Object: To obtain simple and reliable coupling between a control rod and control rod drive by equipping the lower end of the control rod with an extension provided with lateral protuberances and forming the upper end of an index tube with a recess provided with lateral holes. Structure: The tapering central extension of the control rod is inserted into the recess by lowering the control rod, and then it is further inserted by causing frictional movement of the inclined surfaces of lateral protuberances in frictional contact with guide surfaces. When the lateral protuberances are brought into contact with a stepped portion, the control rod is rotated to fit the lateral protuberances into the lateral holes. In this way, the control rod is coupled to the index tube of the control rod drive. (Yoshino, Y.)

Overexpression, purification, crystallization and preliminary X-ray studies of Vibrio cholerae EpsG

International Nuclear Information System (INIS)

Jens, Jason; Raghunathan, Kannan; Vago, Frank; Arvidson, Dennis

2009-01-01

Recombinant V. cholerae EpsG has been expressed, purified and crystallized. The crystals diffracted to 2.26 Å resolution. EpsG is the major pseudopilin protein of the Vibrio cholerae type II secretion system. An expression plasmid that encodes an N-terminally truncated form of EpsG with a C-terminal noncleavable His tag was constructed. Recombinant EpsG was expressed in Escherichia coli; the truncated protein was purified and crystallized by hanging-drop vapor diffusion against a reservoir containing 6 mM zinc sulfate, 60 mM MES pH 6.5, 15% PEG MME 550. The crystals diffracted X-rays to a resolution of 2.26 Å and belonged to space group P2 1 , with unit-cell parameters a = 88.61, b = 70.02, c = 131.54 Å

Control rod displacement

International Nuclear Information System (INIS)

Nakazato, S.

1987-01-01

This patent describes a nuclear reactor including a core, cylindrical control rods, a single support means supporting the control rods from their upper ends in spaced apart positions and movable for displacing the control rods in their longitudinal direction between a first end position in which the control rods are fully inserted into the core and a second end position in which the control rods are retracted from the core, and guide means contacting discrete regions of the outer surface of each control rod at least when the control rods are in the vicinity of the second end position. The control rods are supported by the support means for longitudinal movement without rotation into and out of the core relative to the guide means to thereby cause the outer surface of the control rods to experience wear as a result of sliding contact with the guide means. The support means are so arranged with respect to the core and the guide means that it is incapable of rotation relative to the guide means. The improvement comprises displacement means being operatively coupled to a respective one of the control rods for periodically rotating the control rod in a single angular direction through an angle selected to change the locations on the outer surfaces of the control rods at which the control rods are contacted by the guide means during subsequent longitudinal movement of the control rods

Properties of truncated multiplicity distributions

International Nuclear Information System (INIS)

Lupia, S.

1995-01-01

Truncation effects on multiplicity distributions are discussed. Observables sensitive to the tail, like factorial moments, factorial cumulants and their ratio, are shown to be strongly affected by truncation. A possible way to overcome this problem by looking at the head of the distribution is suggested. (author)

Properties of truncated multiplicity distributions

Energy Technology Data Exchange (ETDEWEB)

Lupia, S. [Turin Univ. (Italy). Dipt. di Fisica

1995-12-31

Truncation effects on multiplicity distributions are discussed. Observables sensitive to the tail, like factorial moments, factorial cumulants and their ratio, are shown to be strongly affected by truncation. A possible way to overcome this problem by looking at the head of the distribution is suggested. (author)

Morphoelastic rods. Part I: A single growing elastic rod

KAUST Repository

Moulton, D.E.

2013-02-01

A theory for the dynamics and statics of growing elastic rods is presented. First, a single growing rod is considered and the formalism of three-dimensional multiplicative decomposition of morphoelasticity is used to describe the bulk growth of Kirchhoff elastic rods. Possible constitutive laws for growth are discussed and analysed. Second, a rod constrained or glued to a rigid substrate is considered, with the mismatch between the attachment site and the growing rod inducing stress. This stress can eventually lead to instability, bifurcation, and buckling. © 2012 Elsevier Ltd. All rights reserved.

Morphoelastic rods. Part I: A single growing elastic rod

KAUST Repository

Moulton, D.E.; Lessinnes, T.; Goriely, A.

2013-01-01

A theory for the dynamics and statics of growing elastic rods is presented. First, a single growing rod is considered and the formalism of three-dimensional multiplicative decomposition of morphoelasticity is used to describe the bulk growth of Kirchhoff elastic rods. Possible constitutive laws for growth are discussed and analysed. Second, a rod constrained or glued to a rigid substrate is considered, with the mismatch between the attachment site and the growing rod inducing stress. This stress can eventually lead to instability, bifurcation, and buckling. © 2012 Elsevier Ltd. All rights reserved.

Analysis of truncation limit in probabilistic safety assessment

International Nuclear Information System (INIS)

Cepin, Marko

2005-01-01

A truncation limit defines the boundaries of what is considered in the probabilistic safety assessment and what is neglected. The truncation limit that is the focus here is the truncation limit on the size of the minimal cut set contribution at which to cut off. A new method was developed, which defines truncation limit in probabilistic safety assessment. The method specifies truncation limits with more stringency than presenting existing documents dealing with truncation criteria in probabilistic safety assessment do. The results of this paper indicate that the truncation limits for more complex probabilistic safety assessments, which consist of larger number of basic events, should be more severe than presently recommended in existing documents if more accuracy is desired. The truncation limits defined by the new method reduce the relative errors of importance measures and produce more accurate results for probabilistic safety assessment applications. The reduced relative errors of importance measures can prevent situations, where the acceptability of change of equipment under investigation according to RG 1.174 would be shifted from region, where changes can be accepted, to region, where changes cannot be accepted, if the results would be calculated with smaller truncation limit

Control rod drive

International Nuclear Information System (INIS)

Hawke, B.C.

1986-01-01

A reactor core, one or more control rods, and a control rod drive are described for selectively inserting and withdrawing the one or more control rods into and from the reactor core, which consists of: a support structure secured beneath the reactor core; control rod positioning means supported by the support structure for movably supporting the control rod for movement between a lower position wherein the control rod is located substantially beneath the reactor core and an upper position wherein at least an upper portion of the control rod extends into the reactor core; transmission means; primary drive means connected with the control rod positioning means by the transmission means for positioning the control rod under normal operating conditions; emergency drive means for moving the control rod from the lower position to the upper position under emergency conditions, the emergency drive means including a weight movable between an upper and a lower position, means for movably supporting the weight, and means for transmitting gravitational force exerted on the weight to the control rod positioning means to move the control rod upwardly when the weight is pulled downwardly by gravity; the transmission means connecting the control rod positioning means with the emergency drive means so that the primary drive means effects movement of the weight and the control rod in opposite directions under normal conditions, thus providing counterbalancing to reduce the force required for upward movement of the control rod under normal conditions; and restraint means for restraining the fall of the weight under normal operating conditions and disengaging the primary drive means to release the weight under emergency conditions

Truncated Calogero-Sutherland models

Science.gov (United States)

Pittman, S. M.; Beau, M.; Olshanii, M.; del Campo, A.

2017-05-01

A one-dimensional quantum many-body system consisting of particles confined in a harmonic potential and subject to finite-range two-body and three-body inverse-square interactions is introduced. The range of the interactions is set by truncation beyond a number of neighbors and can be tuned to interpolate between the Calogero-Sutherland model and a system with nearest and next-nearest neighbors interactions discussed by Jain and Khare. The model also includes the Tonks-Girardeau gas describing impenetrable bosons as well as an extension with truncated interactions. While the ground state wave function takes a truncated Bijl-Jastrow form, collective modes of the system are found in terms of multivariable symmetric polynomials. We numerically compute the density profile, one-body reduced density matrix, and momentum distribution of the ground state as a function of the range r and the interaction strength.

Lamp with a truncated reflector cup

Science.gov (United States)

Li, Ming; Allen, Steven C.; Bazydola, Sarah; Ghiu, Camil-Daniel

2013-10-15

A lamp assembly, and method for making same. The lamp assembly includes first and second truncated reflector cups. The lamp assembly also includes at least one base plate disposed between the first and second truncated reflector cups, and a light engine disposed on a top surface of the at least one base plate. The light engine is configured to emit light to be reflected by one of the first and second truncated reflector cups.

Analysis of photonic band gaps in two-dimensional photonic crystals with rods covered by a thin interfacial layer

International Nuclear Information System (INIS)

Trifonov, T.; Marsal, L.F.; Pallares, J.; Rodriguez, A.; Alcubilla, R.

2004-01-01

We investigate different aspects of the absolute photonic band gap (PBG) formation in two-dimensional photonic structures consisting of rods covered with a thin dielectric film. Specifically, triangular and honeycomb lattices in both complementary arrangements, i.e., air rods drilled in silicon matrix and silicon rods in air, are studied. We consider that the rods are formed of a dielectric core (silicon or air) surrounded by a cladding layer of silicon dioxide (SiO 2 ), silicon nitride (Si 3 N 4 ), or germanium (Ge). Such photonic lattices present absolute photonic band gaps, and we study the evolution of these gaps as functions of the cladding material and thickness. Our results show that in the case of air rods in dielectric media the existence of dielectric cladding reduces the absolute gap width and may cause complete closure of the gap if thick layers are considered. For the case of dielectric rods in air, however, the existence of a cladding layer can be advantageous and larger absolute PBG's can be achieved

Formal truncations of connected kernel equations

International Nuclear Information System (INIS)

Dixon, R.M.

1977-01-01

The Connected Kernel Equations (CKE) of Alt, Grassberger and Sandhas (AGS); Kouri, Levin and Tobocman (KLT); and Bencze, Redish and Sloan (BRS) are compared against reaction theory criteria after formal channel space and/or operator truncations have been introduced. The Channel Coupling Class concept is used to study the structure of these CKE's. The related wave function formalism of Sandhas, of L'Huillier, Redish and Tandy and of Kouri, Krueger and Levin are also presented. New N-body connected kernel equations which are generalizations of the Lovelace three-body equations are derived. A method for systematically constructing fewer body models from the N-body BRS and generalized Lovelace (GL) equations is developed. The formally truncated AGS, BRS, KLT and GL equations are analyzed by employing the criteria of reciprocity and two-cluster unitarity. Reciprocity considerations suggest that formal truncations of BRS, KLT and GL equations can lead to reciprocity-violating results. This study suggests that atomic problems should employ three-cluster connected truncations and that the two-cluster connected truncations should be a useful starting point for nuclear systems

Cloning, expression, purification, crystallization and preliminary X-ray analysis of Thermus aquaticus succinyl-CoA synthetase

International Nuclear Information System (INIS)

Joyce, Michael A.; Brownie, Edward R.; Hayakawa, Koto; Fraser, Marie E.

2007-01-01

Attempts to crystallize succinyl-CoA synthetase from the thermophile T. aquaticus were thwarted by proteolysis of the β-subunit and preferential crystallization of a truncated form. Crystals of the full-length enzyme were grown after the purification protocol was modified to include frequent additions of protease inhibitors. Succinyl-CoA synthetase (SCS) is an enzyme of the citric acid cycle and is thus found in most species. To date, there are no structures available of SCS from a thermophilic organism. To investigate how the enzyme adapts to higher temperatures, SCS from Thermus aquaticus was cloned, overexpressed, purified and crystallized. Attempts to crystallize the enzyme were thwarted by proteolysis of the β-subunit and preferential crystallization of the truncated form. Crystals of full-length SCS were grown after the purification protocol was modified to include frequent additions of protease inhibitors. The resulting crystals, which diffract to 2.35 Å resolution, are of the protein in complex with Mn 2+ -GDP

Guided-Wave Testing of Trunnion Rods at Greenup Lock and Dam, Kentucky

Science.gov (United States)

2014-04-01

fatigue cracks which go through opening and closing periods during their progression, microcracks in post-tension trunnion anchor rods are believed to be...produce undesired interference effects. A new 1.5 in. diameter, medium-damped lead zirconate titanate ( PZT ), ceramic-based crystal (i.e., an Accuscan

Perspective on rainbow-ladder truncation

International Nuclear Information System (INIS)

Eichmann, G.; Alkofer, R.; Krassnigg, A.; Cloeet, I. C.; Roberts, C. D.

2008-01-01

Prima facie the systematic implementation of corrections to the rainbow-ladder truncation of QCD's Dyson-Schwinger equations will uniformly reduce in magnitude those calculated mass-dimensioned results for pseudoscalar and vector meson properties that are not tightly constrained by symmetries. The aim and interpretation of studies employing rainbow-ladder truncation are reconsidered in this light

Single crystal growth of high-temperature superconductor Bi2.1Sr1.9Ca1.0Cu2.0AlyOx

International Nuclear Information System (INIS)

Gu, G.D.; Lin, Z.W.

2000-01-01

The effect of Al doping on the crystal growth of Bi-2212 was studied by a floating zone method. The results show that the planar solid-liquid interface breaks down into a cellular growth front while increasing Al doping in the rods of Bi 2.1 Sr 1.9 Ca 1.0 Cu 2.0 Al y O x . The size of the single crystals decreases with the increase in Al doping. The solubility limit for Al or the maximum Cu-site substitution by Al in the Bi-2212 crystals is less than y = 0.01. The majority of nominal Al doping in the rods forms an Al-rich phase in the grain boundaries of the single crystals. The superconductivity of as-grown Al-doped crystals decreases progressively with increasing Al doping in the rods, however, the T c for annealed Al-doped crystals does not change with increasing Al doping in the rods. The unchanged T c for annealed Al-doped Bi-2212 crystals either suggests that a small amount of Al substitution in the Cu site does not cause T c to drop significantly, or indicates that Al only enters the Bi-2212 crystals as an impurity, but does not substitute at the Cu site in the Bi-2212 crystals. (author)

Crystal structure of the P pilus rod subunit PapA.

Directory of Open Access Journals (Sweden)

Denis Verger

2007-05-01

Full Text Available P pili are important adhesive fibres involved in kidney infection by uropathogenic Escherichia coli strains. P pili are assembled by the conserved chaperone-usher pathway, which involves the PapD chaperone and the PapC usher. During pilus assembly, subunits are incorporated into the growing fiber via the donor-strand exchange (DSE mechanism, whereby the chaperone's G1 beta-strand that complements the incomplete immunoglobulin-fold of each subunit is displaced by the N-terminal extension (Nte of an incoming subunit. P pili comprise a helical rod, a tip fibrillum, and an adhesin at the distal end. PapA is the rod subunit and is assembled into a superhelical right-handed structure. Here, we have solved the structure of a ternary complex of PapD bound to PapA through donor-strand complementation, itself bound to another PapA subunit through DSE. This structure provides insight into the structural basis of the DSE reaction involving this important pilus subunit. Using gel filtration chromatography and electron microscopy on a number of PapA Nte mutants, we establish that PapA differs in its mode of assembly compared with other Pap subunits, involving a much larger Nte that encompasses not only the DSE region of the Nte but also the region N-terminal to it.

Clustered survival data with left-truncation

DEFF Research Database (Denmark)

Eriksson, Frank; Martinussen, Torben; Scheike, Thomas H.

2015-01-01

Left-truncation occurs frequently in survival studies, and it is well known how to deal with this for univariate survival times. However, there are few results on how to estimate dependence parameters and regression effects in semiparametric models for clustered survival data with delayed entry....... Surprisingly, existing methods only deal with special cases. In this paper, we clarify different kinds of left-truncation and suggest estimators for semiparametric survival models under specific truncation schemes. The large-sample properties of the estimators are established. Small-sample properties...

Replacement rod

International Nuclear Information System (INIS)

Hatfield, S.C.

1989-01-01

This patent describes in an elongated replacement rod for use with fuel assemblies of the type having two end fittings connected by guide tubes with a plurality of rod and guide tube cell defining spacer grids containing rod support features and mixing vanes. The grids secured to the guide tubes in register between the end fittings at spaced intervals. The fuel rod comprising: an asymmetrically beveled tip; a shank portion having a straight centerline; and a permanently diverging portion between the tip and the shank portion

Water rod

International Nuclear Information System (INIS)

Kashiwai, Shin-ichi; Yokomizo, Osamu; Orii, Akihito.

1992-01-01

In a reactor core of a BWR type reactor, the area of a flow channel in a lower portion of a downcoming pipe for downwardly releasing steams present at the top portion in a water rod is increased. Further, a third coolant flow channel (an inner water rod) is disposed in an uprising having an exit opened near the inlet of the water rod and an inlet opened at the outside near the top portion of the water and having an increase flow channel area in the upper portion. The downcoming pipe in the water rod is filled with steams, and the void ratio is increased by so much as the flow channel area of the downcoming pipe is increased. Since the pressure difference between the inlet and the exit of the inner water rod is greater than the pressure difference between the inlet and the exit of the water rod, most of water flown into the inner water rod is discharged out of the exit in the form of water as it is. Since the area of the flow channel is increased in the portion of the inner water rod, void efficiency in the upper portion of the reactor core is decreased by so much. Since the void ratio is thus increased in the lower portion and the void efficiency is decreased in the upper portion of the reactor core, axial void distribution can be flattened. (N.H.)

The study of thermal tunable coupling between a Superconducting photonic crystal waveguide and semi-circular photonic crystal

Energy Technology Data Exchange (ETDEWEB)

Oskooi, Somayeh; Barvestani, Jamal, E-mail: barvestani@tabrizu.ac.ir

2016-08-15

Highlights: • The light coupling between superconducting photonic crystal waveguide and a semi-circular photonic crystal has been studied. • We utilized the finite difference time domain and plane wave expansion methods in the calculations. • The effect of the size of the nearest neighbor rods of waveguide on the coupling efficiency has been investigated. • The coupling efficiencies are reported versus the temperature of the superconducting waveguide. - Abstract: Through the present study, we investigated the light coupling between superconducting photonic crystal waveguide and a semi-circular photonic crystal. By using the finite difference time domain method, we evaluated the coupling efficiency between the mentioned structures at the various temperatures for different waveguide sizes. Calculation demonstrated that the coupling efficiency strongly depended on the temperature of the superconductor. The peak value of the coupling efficiency was influenced by the size of the nearest neighbor rods of waveguide. The results have shown that it is possible to obtain high efficiency at the desired temperature with proper selection of physical parameters in far-infrared frequency region. This structure has great potential in the optical integration and other areas.

The effect of polycrystalline rod insertion in a low Prandtl number melt for continuous Czochralski system

Science.gov (United States)

Nam, Phil-Ouk; Son, Seung-Suk; Yi, Kyung-Woo

2010-04-01

The increased wafer size results in greater instabilities and complexities within the silicon melt, and melt flow control through the application of magnetic fields is not adequate to stabilize the melt. Therefore, continuous Czochralski systems are being studied as a solution to these issues, with higher productivity and no change in size. The purpose of this study is to observe the effects of polycrystalline rod insertion on the melt for a continuous Czochralski system. In order to observe flow patterns within the melt both broadly and specifically, we employ experimentation on a model system in tandem with numerical simulation. The rod insertion do not significantly affect near the crystal edge. In the melt height from 0.14 to 0.09 m, an asymmetric temperature distributions arise when the crystal rotation is counterclockwise direction (-15 rpm) and the crucible rotation is clockwise direction (3 rpm). The axis-symmetrical temperature distribution is formed at lower melt heights (0.08 and 0.07 m). When the melt height is 0.07 m, the axis-symmetric temperature distribution is maintained even after the rod insertion.

Expression, purification and crystallization of two major envelope proteins from white spot syndrome virus

International Nuclear Information System (INIS)

Tang, Xuhua; Hew, Choy Leong

2007-01-01

The crystallization of the N-terminal transmembrane region-truncated VP26 and VP28 of white spot syndrome virus is described. White spot syndrome virus (WSSV) is a major virulent pathogen known to infect penaeid shrimp and other crustaceans. VP26 and VP28, two major envelope proteins from WSSV, have been identified and overexpressed in Escherichia coli. In order to facilitate purification and crystallization, predicted N-terminal transmembrane regions of approximately 35 amino acids have been truncated from both VP26 and VP28. Truncated VP26 and VP28 and their corresponding SeMet-labelled proteins were purified and the SeMet proteins were crystallized by the hanging-drop vapour-diffusion method. Crystals of SeMet-labelled VP26 were obtained using a reservoir consisting of 0.1 M citric acid pH 3.5, 3.0 M sodium chloride and 1%(w/v) polyethylene glycol 3350, whereas SeMet VP28 was crystallized using a reservoir solution consisting of 25% polyethylene glycol 8000, 0.2 M calcium acetate, 0.1 M Na HEPES pH 7.5 and 1.5%(w/v) 1,2,3-heptanetriol. Crystals of SeMet-labelled VP26 diffract to 2.2 Å resolution and belong to space group R32, with unit-cell parameters a = b = 73.92, c = 199.31 Å. SeMet-labelled VP28 crystallizes in space group P2 1 2 1 2 1 , with unit-cell parameters a = 105.33, b = 106.71, c = 200.37 Å, and diffracts to 2.0 Å resolution

Expression, purification and crystallization of two major envelope proteins from white spot syndrome virus

Energy Technology Data Exchange (ETDEWEB)

Tang, Xuhua; Hew, Choy Leong, E-mail: dbshewcl@nus.edu.sg [Department of Biological Sciences, National University of Singapore, 14 Science Drive 4, Singapore 117543 (Singapore)

2007-07-01

The crystallization of the N-terminal transmembrane region-truncated VP26 and VP28 of white spot syndrome virus is described. White spot syndrome virus (WSSV) is a major virulent pathogen known to infect penaeid shrimp and other crustaceans. VP26 and VP28, two major envelope proteins from WSSV, have been identified and overexpressed in Escherichia coli. In order to facilitate purification and crystallization, predicted N-terminal transmembrane regions of approximately 35 amino acids have been truncated from both VP26 and VP28. Truncated VP26 and VP28 and their corresponding SeMet-labelled proteins were purified and the SeMet proteins were crystallized by the hanging-drop vapour-diffusion method. Crystals of SeMet-labelled VP26 were obtained using a reservoir consisting of 0.1 M citric acid pH 3.5, 3.0 M sodium chloride and 1%(w/v) polyethylene glycol 3350, whereas SeMet VP28 was crystallized using a reservoir solution consisting of 25% polyethylene glycol 8000, 0.2 M calcium acetate, 0.1 M Na HEPES pH 7.5 and 1.5%(w/v) 1,2,3-heptanetriol. Crystals of SeMet-labelled VP26 diffract to 2.2 Å resolution and belong to space group R32, with unit-cell parameters a = b = 73.92, c = 199.31 Å. SeMet-labelled VP28 crystallizes in space group P2{sub 1}2{sub 1}2{sub 1}, with unit-cell parameters a = 105.33, b = 106.71, c = 200.37 Å, and diffracts to 2.0 Å resolution.

Control rod

International Nuclear Information System (INIS)

Igarashi, Takao; Yoshimoto, Yuichiro; Sugawara, Satoshi; Fukumoto, Takashi; Endo, Zen-ichiro; Saito, Shozo; Shinpo, Katsutoshi; Nishimura, Akira; Ozawa, Michihiro

1988-01-01

Purpose: To provide a sufficient shutdown margin upon reactor shutdown, prevent sheath deformation without decreasing neutron absorbents and prevent impact shocks exerted to structural materials. Constitution: The control rod of the present invention comprises a neutron absorption region, a sheath deformation means attached to the side wall and means for restricting and supporting axial movement of the neutron absorbent rod. Then, the amount of absorptive nuclei chained absorbents in the lower region is reduced than that in the upper region. In this way, effective neutron absorbing performance can be obtained relative to the neutron importance distribution during reactor shutdown. In addition, since the operationability is improved by reducing the weight of the control rod and the absorptive nuclei chained neutron abosrbers are used, mechanical nuclear life of the control rod can be increased. Thus, it is possible to prevent the outward deformation of the sheath, as well as prevent collision between the neutron absorber rod and the structural material on the side of inserting the control rod generated upon reactor scram by a simple structure. (Kamimura, M.)

Purification and crystallization of Phd, the antitoxin of the phd/doc operon

International Nuclear Information System (INIS)

Garcia-Pino, Abel; Sterckx, Yann; Vandenbussche, Guy; Loris, Remy

2010-01-01

The antitoxin Phd from the phd/doc operon of bacteriophage P1 was crystallized in two distinct crystal forms. The antitoxin Phd from the phd/doc module of bacteriophage P1 was crystallized in two distinct crystal forms. Crystals of His-tagged Phd contain a C-terminally truncated version of the protein and diffract to 2.20 Å resolution. Crystals of untagged Phd purified from the Phd–Doc complex diffract to 2.25 Å resolution. These crystals are partially merohedrally twinned and contain the full-length version of the protein

Control rod drives

International Nuclear Information System (INIS)

Futatsugi, Masao.

1980-01-01

Purpose: To secure the reactor operation safety by the provision of a fluid pressure detecting section for control rod driving fluid and a control rod interlock at the midway of the flow pass for supplying driving fluid to the control rod drives. Constitution: Between a driving line and a direction control valve are provided a pressure detecting portion, an alarm generating device, and a control rod inhibition interlock. The driving fluid from a driving fluid source is discharged by way of a pump and a manual valve into the reactor in which the control rods and reactor fuels are contained. In addition, when the direction control valve is switched and the control rods are inserted and extracted by the control rod drives, the pressure in the driving line is always detected by the pressure detection section, whereby if abnormal pressure is resulted, the alarm generating device is actuated to warn the abnormality and the control rod inhibition interlock is actuated to lock the direction control valve thereby secure the safety operation of the reactor. (Seki, T.)

Control rod drives

International Nuclear Information System (INIS)

Oonuki, Koji.

1981-01-01

Purpose: To increase the driving speed of control rods at rapid insertion with an elongate control rod and an extension pipe while ensuring sufficient buffering performance in a short buffering distance, by providing a plurality of buffers to an extension pipe between a control rod drive source and a control rod in LMFBR type reactor. Constitution: First, second and third buffers are respectively provided to an acceleration piston, an extension pipe and a control rod respectively and the insertion positions for each of the buffers are displaced orderly from above to below. Upon disconnection of energizing current for an electromagnet, the acceleration piston, the extension pipe and the control rod are rapidly inserted in one body. The first, second and third buffers are respectively actuated at each of their falling strokes upon rapid insertion respectively, and the acceleration piston, the extension pipe and the control rod receive the deceleration effect in the order correspondingly. Although the compression force is applied to the control rod only near the stroke end, it does not cause deformation. (Kawakami, Y.)

Truncation correction for oblique filtering lines

International Nuclear Information System (INIS)

Hoppe, Stefan; Hornegger, Joachim; Lauritsch, Guenter; Dennerlein, Frank; Noo, Frederic

2008-01-01

State-of-the-art filtered backprojection (FBP) algorithms often define the filtering operation to be performed along oblique filtering lines in the detector. A limited scan field of view leads to the truncation of those filtering lines, which causes artifacts in the final reconstructed volume. In contrast to the case where filtering is performed solely along the detector rows, no methods are available for the case of oblique filtering lines. In this work, the authors present two novel truncation correction methods which effectively handle data truncation in this case. Method 1 (basic approach) handles data truncation in two successive preprocessing steps by applying a hybrid data extrapolation method, which is a combination of a water cylinder extrapolation and a Gaussian extrapolation. It is independent of any specific reconstruction algorithm. Method 2 (kink approach) uses similar concepts for data extrapolation as the basic approach but needs to be integrated into the reconstruction algorithm. Experiments are presented from simulated data of the FORBILD head phantom, acquired along a partial-circle-plus-arc trajectory. The theoretically exact M-line algorithm is used for reconstruction. Although the discussion is focused on theoretically exact algorithms, the proposed truncation correction methods can be applied to any FBP algorithm that exposes oblique filtering lines.

Enhanced complete photonic bandgap in a moderate refractive index contrast chalcogenide-air system with connected-annular-rods photonic crystals

KAUST Repository

Hou, Jin

2018-03-27

Connected-annular-rods photonic crystals (CARPCs) in both triangular and square lattices are proposed to enhance the two-dimensional complete photonic bandgap (CPBG) for chalcogenide material systems with moderate refractive index contrast. For the typical chalcogenide-glass–air system with an index contrast of 2.8:1, the optimized square lattice CARPC exhibits a significantly larger normalized CPBG of about 13.50%, though the use of triangular lattice CARPC is unable to enhance the CPBG. It is almost twice as large as our previously reported result [IEEE J. Sel. Top. Quantum Electron. 22, 4900108 (2016) [CrossRef] ]. Moreover, the CPBG of the square-lattice CARPC could remain until an index contrast as low as 2.24:1. The result not only favors wideband CPBG applications for index contrast systems near 2.8:1, but also makes various optical applications that are dependent on CPBG possible for more widely refractive index contrast systems.

Proteolysis of truncated hemolysin A yields a stable dimerization interface

Energy Technology Data Exchange (ETDEWEB)

Novak, Walter R.P.; Bhattacharyya, Basudeb; Grilley, Daniel P.; Weaver, Todd M. (Wabash); (UW)

2017-02-21

Wild-type and variant forms of HpmA265 (truncated hemolysin A) fromProteus mirabilisreveal a right-handed, parallel β-helix capped and flanked by segments of antiparallel β-strands. The low-salt crystal structures form a dimeric structureviathe implementation of on-edge main-chain hydrogen bonds donated by residues 243–263 of adjacent monomers. Surprisingly, in the high-salt structures of two variants, Y134A and Q125A-Y134A, a new dimeric interface is formedviamain-chain hydrogen bonds donated by residues 203–215 of adjacent monomers, and a previously unobserved tetramer is formed. In addition, an eight-stranded antiparallel β-sheet is formed from the flap regions of crystallographically related monomers in the high-salt structures. This new interface is possible owing to additional proteolysis of these variants after Tyr240. The interface formed in the high-salt crystal forms of hemolysin A variants may mimic the on-edge β-strand positioning used in template-assisted hemolytic activity.

Effects of Purification on the Crystallization of Lysozyme

Science.gov (United States)

Ewing, Felecia L.; Forsythe, Elizabeth L.; Van Der Woerd, Mark; Pusey, Marc L.

1996-01-01

We have additionally purified a commercial lysozyme preparation by cation exchange chromatography, followed by recrystallization. This material is 99.96% pure with respect to macromolecular impurities. At basic pH, the purified lysozyme gave only tetragonal crystals at 20 C. Protein used directly from the bottle, prepared by dialysis against distilled water, or which did not bind to the cation exchange column had considerably altered crystallization behavior. Lysozyme which did not bind to the cation exchange column was subsequently purified by size exclusion chromatography. This material gave predominately bundles of rod-shaped crystals with some small tetragonal crystals at lower pHs. The origin of the bundled rod habit was postulated to be a thermally dependent tetragonal- orthorhombic change in the protein structure. This was subsequently ruled out on the basis of crystallization behavior and growth rate experiments. This suggests that heterogeneous forms of lysozyme may be responsible. These results demonstrate three classes of impurities: (1) small molecules, which may be removed by dialysis; (2) macromolecules, which are removable by chromatographic techniques; and (3) heterogeneous forms of the protein, which can be removed in this case by cation exchange chromatography. Of these, heterogeneous forms of the lysozyme apparently have the greatest affect on its crystallization behavior.

Lead tungstate crystal of the ALICE Photon Spectrometer (PHOS)

CERN Document Server

Patrice Loïez

2002-01-01

A consignment of 500 lead tungstate crystals arrived at CERN from the northern Russian town of Apatity in May. Destined for the ALICE heavy-ion experiment in preparation for the Large Hadron Collider, each crystal is an 18 cm long rod with a 2.2 cm square section, and weighs some 750 g. A total of 17 000 crystals will make up the experiment's photon spectrometer.

Control rod cluster with removable rods for nuclear fuel assembly

International Nuclear Information System (INIS)

Denizou, J.P.

1989-01-01

For each removable control rod, the open end section of the sleeve has a certain length of reduced diameter with openings in its wall. The top end of the rod is joined to an extension tube that surrounds the shaft over part of its lenght. This extension tube fits over the reduced part of the sleeve when the shaft is screwed into the bore of the sleeve. Rotation of the rod in the sleeve is prevented by deforming the extension tube locally in the openings of the end part of the sleeve. The rod is dismantled by exerting a torque on it using a gripping area near the end of the rod [fr

Identification of a Novel Homozygous Nonsense Mutation Confirms the Implication of GNAT1 in Rod-Cone Dystrophy.

Directory of Open Access Journals (Sweden)

Cécile Méjécase

Full Text Available GNAT1, encoding the transducin subunit Gα, is an important element of the phototransduction cascade. Mutations in this gene have been associated with autosomal dominant and autosomal recessive congenital stationary night blindness. Recently, a homozygous truncating GNAT1 mutation was identified in a patient with late-onset rod-cone dystrophy. After exclusion of mutations in genes underlying progressive inherited retinal disorders, by targeted next generation sequencing, a 32 year-old male sporadic case with severe rod-cone dystrophy and his unaffected parents were investigated by whole exome sequencing. This led to the identification of a homozygous nonsense variant, c.963C>A p.(Cys321* in GNAT1, which was confirmed by Sanger sequencing. The mother was heterozygous for this variant whereas the variant was absent in the father. c.963C>A p.(Cys321* is predicted to produce a shorter protein that lacks critical sites for the phototransduction cascade. Our work confirms that the phenotype and the mode of inheritance associated with GNAT1 variants can vary from autosomal dominant, autosomal recessive congenital stationary night blindness to autosomal recessive rod-cone dystrophy.

Control rod drive mechanism

International Nuclear Information System (INIS)

Nakamura, Akira.

1981-01-01

Purpose: To ensure the scram operation of a control rod by the reliable detection for the position of control rods. Constitution: A permanent magnet is provided to the lower portion of a connecting rod in engagement with a control rod and a tube having a plurality of lead switches arranged axially therein in a predetermined pitch is disposed outside of the control rod drives. When the control rod moves upwardly in the scram operation, the lead switches are closed successively upon passage of the permanent magnet to operate the electrical circuit provided by way of each of the lead switches. Thus, the position for the control rod during the scram can reliably be determined and the scram characteristic of the control rod can be recognized. (Furukawa, Y.)

On the perfect hexagonal packing of rods

International Nuclear Information System (INIS)

Starostin, E L

2006-01-01

In most cases the hexagonal packing of fibrous structures or rods extremizes the energy of interaction between strands. If the strands are not straight, then it is still possible to form a perfect hexatic bundle. Conditions under which the perfect hexagonal packing of curved tubular structures may exist are formulated. Particular attention is given to closed or cycled arrangements of the rods like in the DNA toroids and spools. The closure or return constraints of the bundle result in an allowable group of automorphisms of the cross-sectional hexagonal lattice. The structure of this group is explored. Examples of open helical-like and closed toroidal-like bundles are presented. An expression for the elastic energy of a perfectly packed bundle of thin elastic rods is derived. The energy accounts for both the bending and torsional stiffnesses of the rods. It is shown that equilibria of the bundle correspond to solutions of a variational problem formulated for the curve representing the axis of the bundle. The functional involves a function of the squared curvature under the constraints on the total torsion and the length. The Euler-Lagrange equations are obtained in terms of curvature and torsion and due to the existence of the first integrals the problem is reduced to the quadrature. The three-dimensional shape of the bundle may be readily reconstructed by integration of the Ilyukhin-type equations in special cylindrical coordinates. The results are of universal nature and are applicable to various fibrous structures, in particular, to intramolecular liquid crystals formed by DNA condensed in toroids or packed inside the viral capsids

Method of inserting fuel rod

International Nuclear Information System (INIS)

Kamimoto, Shuji; Imoo, Makoto; Tsuchida, Kenji.

1991-01-01

The present invention concerns a method of inserting a fuel rod upon automatic assembling, automatic dismantling and reassembling of a fuel assembly in a light water moderated reactor, as well as a device and components used therefor. That is, a fuel rod is inserted reliably to an aimed point of insertion by surrounding the periphery of the fuel rod to be inserted with guide rods, and thereby suppressing the movement of the fuel rod during insertion. Alternatively, a fuel rod is inserted reliably to a point of insertion by inserting guide rods at the periphery of the point of insertion for the fuel rod to be inserted thereby surrounding the point of insertion with the guide rods or fuel rods. By utilizing fuel rods already present in the fuel assembly as the guide rods described above, the fuel rod can be inserted reliably to the point of insertion with no additional devices. Dummy fuel rods are previously inserted in a fuel assembly which are then utilized as the above-mentioned guide rods to accurately insert the fuel rod to the point of insertion. (I.S.)

Water Assisted Growth of C₆₀ Rods and Tubes by Liquid–Liquid Interfacial Precipitation Method

Directory of Open Access Journals (Sweden)

Cheuk-Wai Tai

2012-06-01

Full Text Available C₆₀ nanorods with hexagonal cross sections are grown using a static liquid–liquid interfacial precipitation method in a system of C₆₀/m-dichlorobenzene solution and ethanol. Adding water to the ethanol phase leads instead to C₆₀ tubes where both length and diameter of the C₆₀ tubes can be controlled by the water content in the ethanol. Based on our observations we find that the diameter of the rods/tubes strongly depends on the nucleation step. We propose a liquid-liquid interface growth model of C₆₀ rods and tubes based on the diffusion rate of the good C₆₀ containing solvent into the poor solvent as well as on the size of the crystal seeds formed at the interface between the two solvents. The grown rods and tubes exhibit a hexagonal solvate crystal structure with m-dichlorobenzene solvent molecules incorporated into the crystal structure, independent of the water content. An annealing step at 200 °C at a pressure < 1 kPa transforms the grown structures into a solvent-free face centered cubic structure. Both the hexagonal and the face centered cubic structures are very stable and neither morphology nor structure shows any signs of degradation after three months of storage.

Control rod drives

International Nuclear Information System (INIS)

Hayakawa, Hiroyasu.

1979-01-01

Purpose: To enable rapid control in a simple circuit by providing a motor control device having an electric capacity capable of simultaneously driving all of the control rods rapidly only in the inserting direction as well as a motor controlling device capable of fine control for the insertion and extraction at usual operation. Constitution: The control rod drives comprise a first motor control device capable of finely controlling the control rods both in inserting and extracting directions, a second motor control device capable of rapidly driving the control rods only in the inserting direction, and a first motor switching circuit and a second motor switching circuit switched by switches. Upon issue of a rapid insertion instruction for the control rods, the second motor switching circuit is closed by the switch and the second motor control circuit and driving motors are connected. Thus, each of the control rod driving motors is driven at a high speed in the inserting direction to rapidly insert all of the control rods. (Yoshino, Y.)

Active and passive vibration isolation in piezoelectric phononic rods with external voltage excitation

Directory of Open Access Journals (Sweden)

Qicheng Zhang

2017-05-01

Full Text Available Active piezoelectric materials are applied to one-dimensional phononic crystals, for the control of longitudinal vibration propagation both in active and passive modes. Based on the electromechanical coupling between the acoustical vibration and electric field, the electromechanical equivalent method is taken to theoretically predict the transmission spectrum of the longitudinal vibration. It is shown that the phononic rod can suppress the vibration efficiently at the frequencies of interest, by actively optimizing the motions of piezoelectric elements. In an illustrated phononic rod of 11.2cm long, active tunable isolations of more than 20dB at low frequencies (500Hz-14kHz are generated by controlling the excitation voltages of piezoelectric elements. Meanwhile, passive fixed isolation at high frequencies (14k-63kHz are presented by its periodicity characteristics. Finite element simulations and vibration experiments on the rod demonstrate the effectiveness of the approach in terms of its vibration isolation capabilities and tunable characteristics. This phononic rod can be manufactured easily and provides numerous potential applications in designing isolation mounts and platforms.

Fabrication and optical characteristics of silicon-based two-dimensional wavelength division multiplexing splitter with photonic crystal directional waveguide couplers

International Nuclear Information System (INIS)

Liu, Cheng-Yang

2011-01-01

Photonic crystals have many potential applications because of their ability to control lightwave propagation. We report on the fabrication and optical properties of quasi-two-dimensional photonic crystals with triangular lattice of dielectric rods in air. Rod-type photonic crystal structures were fabricated in silicon by electron beam lithography and dry-etching techniques. Wavelength division multiplexing splitters were fabricated from two-dimensional photonic crystal directional waveguide couplers. Transmission spectra were measured and device operation was shown to be in agreement with theoretical calculations. The splitters can be used in visible light region. Such an approach to photonic element systems should enable new applications for designing components in photonic integrated circuits. -- Highlights: → We report the fabrication and optical properties of rod-type photonic crystal. → The splitter was fabricated by electron beam lithography and dry-etching techniques. → The splitter was composed of directional waveguide couplers. → Measured transmission spectra are in agreement with theoretical calculations. → The splitters can be used in visible light region.

Fission reactor control rod

International Nuclear Information System (INIS)

Irie, Tomoo.

1991-01-01

The present invention concerns a control rod in a PWR type reactor. A control rod has an inner cladding tube and an outer cladding tube disposed coaxially, and a water draining hole is formed at the inside of the inner cladding tube. Neutron absorbers are filled in an annular gap between the outer cladding tube and the inner cladding tube. The water draining hole opens at the lower end thereof to the top end of the control rod and at the upper end thereof to the side of the upper end plug of the control rod. If the control rod is dropped to a control rod guide thimble for reactor scram, coolants from the control rod guide thimble are flown from the lower end of the water draining hole and discharged from the upper end passing through the water draining hole. In this way, water from the control rod guide thimble is removed easily when the control rod is dropped. Further, the discharging amount of water itself is reduced by the provision of the water draining hole. Accordingly, sufficient control rod dropping speed can be attained. (I.N.)

Fuel rod simulator effects in flooding experiments single rod tests

International Nuclear Information System (INIS)

Nishida, M.

1984-09-01

The influence of a gas filled gap between cladding and pellet on the quenching behavior of a PWR fuel rod during the reflood phase of a LOCA has been investigated. Flooding experiments were conducted with a short length electrically heated single fuel rod simulator surrounded by glass housing. The gap of 0.05 mm width between the Zircaloy cladding and the internal Al 2 O 3 pellets of the rod was filled either wit helium or with argon to vary the radial heat resistance across the gap. This report presents some typical data and an evaluation of the reflood behavior of the fuel rod simulator used. The results show that the quench front propagates faster for increasing heat resistance in the gap between cladding and heat source of the rod. (orig.) [de

Crystallization and preliminary X-ray crystallographic studies of human FAIM protein

International Nuclear Information System (INIS)

Li, Guoming; Qu, Linglong; Meng, Geng; Bai, Xiaoyun; Dai, Kesheng; Zheng, Xiaofeng

2010-01-01

Full-length human Fas apoptosis inhibitory molecule (FAIM) and two truncation constructs have successfully been cloned, expressed and purified in Escherichia coli. FAIM (1–90) was crystallized and diffracted to a resolution of 2.5 Å. Fas apoptosis inhibitory molecule (FAIM), an antagonist of Fas-induced cell death, is highly conserved and is broadly expressed in many tissues. It has been found that FAIM can stimulate neurite outgrowth in PC12 cells and primary neurons. However, the molecular mechanisms of action of FAIM are not understood in detail. Here, full-length human FAIM and two truncation constructs have successfully been cloned, expressed and purified in Escherichia coli. FAIM (1–90) was crystallized and diffracted to a resolution of 2.5 Å; the crystal belonged to space group P3 1 , with unit-cell parameters a = b = 58.02, c = 71.11 Å, α = β = 90, γ = 120°. There were two molecules in the asymmetric unit

Oscillations of the crystal-melt interface caused by harmonic oscillations of the pulling rate for the cylindrical phase of crystal growth

Science.gov (United States)

Vasil'ev, M. G.

2017-02-01

A technique for measuring the crystal cross-sectional area with a weight sensor based on the difference between its readings at the extreme rod positions in the stepwise and continuous modes of modulation of the pulling rate is proposed for the low-thermal gradient Czochralski method. A change in the crystallization rate at harmonic oscillations of the pulling rate is estimated with the aim of conserving the quality of the growing crystal for this measurement method.

Maximum/minimum asymmetric rod detection

International Nuclear Information System (INIS)

Huston, J.T.

1990-01-01

This patent describes a system for determining the relative position of each control rod within a control rod group in a nuclear reactor. The control rod group having at least three control rods therein. It comprises: means for producing a signal representative of a position of each control rod within the control rod group in the nuclear reactor; means for establishing a signal representative of the highest position of a control rod in the control rod group in the nuclear reactor; means for establishing a signal representative of the lowest position of a control rod in the control rod group in the nuclear reactor; means for determining a difference between the signal representative of the position of the highest control rod and the signal representative of the position of the lowest control rod; means for establishing a predetermined limit for the difference between the signal representative of the position of the highest control rod and the signal representative of the position of the lowest control rod; and means for comparing the difference between the signals with the predetermined limit. The comparing means producing an output signal when the difference between the signals exceeds the predetermined limit

Analysis of the upper-truncated Weibull distribution for wind speed

International Nuclear Information System (INIS)

Kantar, Yeliz Mert; Usta, Ilhan

2015-01-01

Highlights: • Upper-truncated Weibull distribution is proposed to model wind speed. • Upper-truncated Weibull distribution nests Weibull distribution as special case. • Maximum likelihood is the best method for upper-truncated Weibull distribution. • Fitting accuracy of upper-truncated Weibull is analyzed on wind speed data. - Abstract: Accurately modeling wind speed is critical in estimating the wind energy potential of a certain region. In order to model wind speed data smoothly, several statistical distributions have been studied. Truncated distributions are defined as a conditional distribution that results from restricting the domain of statistical distribution and they also cover base distribution. This paper proposes, for the first time, the use of upper-truncated Weibull distribution, in modeling wind speed data and also in estimating wind power density. In addition, a comparison is made between upper-truncated Weibull distribution and well known Weibull distribution using wind speed data measured in various regions of Turkey. The obtained results indicate that upper-truncated Weibull distribution shows better performance than Weibull distribution in estimating wind speed distribution and wind power. Therefore, upper-truncated Weibull distribution can be an alternative for use in the assessment of wind energy potential

Control rod drives

International Nuclear Information System (INIS)

Hayakawa, Hiroyasu; Kawamura, Atsuo.

1979-01-01

Purpose: To reduce pellet-clad mechanical interactions, as well as improve the fuel safety. Constitution: In the rod drive of a bwr type reactor, an electric motor operated upon intermittent input such as of pulse signals is connected to a control rod. A resolver for converting the rotational angle of the motor to electric signals is connected to the rotational shaft of the motor and the phase difference between the output signal from the resolver and a reference signal is adapted to detect by a comparator. Based on the detection result, the controller is actuated to control a motor for control rod drive so that fine control for the movement of the control rod is made possible. This can reduce the moving distance of the control rod, decrease the thermal stress applied to the control rod and decrease the pellet clad mechanical interaction failures due to thermal expansion between the cladding tube and the pellets caused by abrupt changes in the generated power. (Furukawa, Y.)

Crystal structure of human protein kinase CK2

DEFF Research Database (Denmark)

Niefind, K; Guerra, B; Ermakowa, I

2001-01-01

The crystal structure of a fully active form of human protein kinase CK2 (casein kinase 2) consisting of two C-terminally truncated catalytic and two regulatory subunits has been determined at 3.1 A resolution. In the CK2 complex the regulatory subunits form a stable dimer linking the two catalyt...... as a docking partner for various protein kinases. Furthermore it shows an inter-domain mobility in the catalytic subunit known to be functionally important in protein kinases and detected here for the first time directly within one crystal structure.......The crystal structure of a fully active form of human protein kinase CK2 (casein kinase 2) consisting of two C-terminally truncated catalytic and two regulatory subunits has been determined at 3.1 A resolution. In the CK2 complex the regulatory subunits form a stable dimer linking the two catalytic...... subunits, which make no direct contact with one another. Each catalytic subunit interacts with both regulatory chains, predominantly via an extended C-terminal tail of the regulatory subunit. The CK2 structure is consistent with its constitutive activity and with a flexible role of the regulatory subunit...

Status of rod consolidation

International Nuclear Information System (INIS)

Bailey, W.J.

1985-04-01

Two of the factors that need to be taken into account with rod consolidation are (1) the effects on rods from their removal from the fuel assembly and (2) the effects on rods as a result of the consolidation process. Potential components of both factors are described in the report. Discussed under (1) are scratches on the fuel rod surfaces, rod breakage, crud, extended burnup, and possible cladding embrittlement due to hydrogen injection at BWRs. Discussed under (2) are the increased water temperature (less than 10 0 C) because of closer packing of the rods, formation of crevices between rods in the close-packed mode, contact with dissimilar metals, and the potential for rapid heating of fuel rods following the loss of water from a spent fuel storage pool. Another factor that plays an important role in rod consolidation is the cost of disposal of the nonfuel-bearing components of the fuel assembly. Also, the dose rate from the components - especially Inconel spacer grids - can affect the handling procedures. Several licensing issues that exist are described. A list of recommendations is provided. 98 refs., 5 figs., 5 tabs

Control rod drive

International Nuclear Information System (INIS)

Okutani, Tetsuro.

1988-01-01

Purpose: To provide a simple and economical control rod drive using a control circuit requiring no pulse circuit. Constitution: Control rods in a BWR type reactor are driven by hydraulic pressure and inserted or withdrawn in the direction of applying the hydraulic pressure. The direction of the hydraulic pressure is controlled by a direction control valve. Since the driving for the control rod is extremely important in view of the operation, a self diagnosis function is disposed for rapid inspection of possible abnormality. In the present invention, two driving contacts are disposed each by one between the both ends of a solenoid valve of the direction control valve for driving the control rod and the driving power source, and diagnosis is conducted by alternately operating them. Therefore, since it is only necessary that the control circuit issues a driving instruction only to one of the two driving contacts, the pulse circuit is no more required. Further, since the control rod driving is conducted upon alignment of the two driving instructions, the reliability of the control rod drive can be improved. (Horiuchi, T.)

Control rod withdrawal monitoring device

International Nuclear Information System (INIS)

Ebisuya, Mitsuo.

1984-01-01

Purpose: To prevent the power ramp even if a plurality of control rods are subjected to withdrawal operation at a time, by reducing the reactivity applied to the reactor. Constitution: The control rod withdrawal monitoring device is adapted to monitor and control the withdrawal of the control rods depending on the reactor power and the monitoring region thereof is divided into a control rod group monitoring region a transition region and a control group monitoring not interfere region. In a case if the distance between a plurality of control rods for which the withdrawal positions are selected is less than a limiting value, the coordinate for the control rods, distance between the control rods and that the control rod distance is shorter are displayed on a display panel, and the withdrawal for the control rods are blocked. Accordingly, even if a plurality of control rods are subjected successively to the withdrawal operation contrary to the control rod withdrawal sequence upon high power operation of the reactor, the power ramp can be prevented. (Kawakami, Y.)

Radiophotoluminescence of alkali-halide crystals stimulated by Bessel laser beam

CERN Document Server

Lyakh, V V; Kochubey, D I; Gyunsburg, K E; Zvezdova, N P; Kochubey, D I; Sedova, Y G; Koronkevich, V P; Poleschuk, A G; Sedukhin, A G

2000-01-01

A new approach to realization of optimal high-resolution reading of deep X-ray images in X-ray-sensitive materials on the base of alkali-halide crystals modified with admixtures has been suggested and investigated experimentally. A possibility to use diffraction axicons with ring aperture for forming micron bright light beams (spatially truncated Bessel beams) which can efficiently de-excite radiophotoluminescence centers lying at large depth in crystals is also presented.

Calcium oxalate crystals: an integral component of the Sclerotinia sclerotiorum/Brassica carinata pathosystem.

Directory of Open Access Journals (Sweden)

Margaret B Uloth

Full Text Available Oxalic acid is an important virulence factor for disease caused by the fungal necrotrophic pathogen Sclerotinia sclerotiorum, yet calcium oxalate (CaOx crystals have not been widely reported. B. carinata stems were infected with S. sclerotiorum and observed using light microscopy. Six hours post inoculation (hpi, CaOx crystals were evident on 46% of stem sections and by 72 hpi on 100%, demonstrating that the secretion of oxalic acid by S. sclerotiorum commences before hyphal penetration. This is the first time CaOx crystals have been reported on B. carinata infected with S. sclerotiorum. The shape of crystals varied as infection progressed. Long tetragonal rods were dominant 12 hpi (68% of crystal-containing samples, but by 72 hpi, 50% of stems displayed bipyramidal crystals, and only 23% had long rods. Scanning electron microscopy from 24 hpi revealed CaOx crystals in all samples, ranging from tiny irregular crystals (< 0.5 μm to large (up to 40 μm highly organized arrangements. Crystal morphology encompassed various forms, including tetragonal prisms, oval plates, crystal sand, and druses. Large conglomerates of CaOx crystals were observed in the hyphal mass 72 hpi and these are proposed as a strategy of the fungus to hold and detoxify Ca2+ions. The range of crystal morphologies suggests that S. sclerotiorum growth and infection controls the form taken by CaOx crystals.

Purification, crystallization and preliminary crystallographic analysis of the CBS pair of the human metal transporter CNNM4

International Nuclear Information System (INIS)

Gómez García, Inmaculada; Oyenarte, Iker; Martínez-Cruz, Luis Alfonso

2011-01-01

This work describes the purification and preliminary crystallographic analysis of the CBS-pair regulatory domain of the human ancient domain protein 4 (ACDP4), also known as CNNM4. This work describes the purification and preliminary crystallographic analysis of the CBS-pair regulatory domain of the human ancient domain protein 4 (ACDP4), also known as CNNM4. ACDP proteins represent the least-studied members of the eight different types of magnesium transporters that have been identified in mammals to date. In humans the ACDP family includes four members: CNNM1–4. CNNM1 acts as a cytosolic copper chaperone and has been associated with urofacial syndrome, whereas CNNM2 and CNNM4 have been identified as magnesium transporters. Interestingly, mutations in the CNNM4 gene have clinical consequences that are limited to retinal function and biomineralization and are considered to be the cause of Jalili syndrome, which consists of autosomal recessive cone-rod dystrophy and amelogenesis imperfecta. The truncated protein was overexpressed, purified and crystallized in the orthorhombic space group C222. The crystals diffracted X-rays to 3.6 Å resolution using synchrotron radiation. Matthews volume calculations suggested the presence of two molecules in the asymmetric unit, which were likely to correspond to a CBS module of the CBS pair of CNNM4

Thermal behavior simulation of a nuclear fuel rod through an eletrically heated rod

International Nuclear Information System (INIS)

Lima, R. de C.F. de.

1984-01-01

In thermalhydraulic loops the nuclear industry often uses electrically heated rods to simulate power transients, which occur in nuclear fuel rods. The development and design of a electrically heated rod, by supplying the dimensions and materials which should be used in order to yeld the same temperature and heat flux at the surfaces of the nuclear rod and the electrically heated rod are presented. To a given nuclear transient this equality was obtained by fitting the linear power through the lumped parameters technique. (Author) [pt

Nuclear fuel rod loading apparatus

International Nuclear Information System (INIS)

King, H.B.; Macivergan, R.; Mckenzie, G.W.

1980-01-01

An apparatus incorporating a microprocessor control is provided for automatically loading nuclear fuel pellets into fuel rods commonly used in nuclear reactor cores. The apparatus comprises a split ''v'' trough for assembling segments of fuel pellets in rows and a shuttle to receive the fuel pellets from the split ''v'' trough when the two sides of the split ''v'' trough are opened. The pellets are weighed while in the shuttle, and the shuttle then moves the pellets into alignment with a fuel rod. A guide bushing is provided to assist the transfer of the pellets into the fuel rod. A rod carousel which holds a plurality of fuel rods presents the proper rod to the guide bushing at the appropriate stage in the loading sequence. The bushing advances to engage the fuel rod, and the shuttle advances to engage the guide bushing. The pellets are then loaded into the fuel rod by a motor operated push rod. The guide bushing includes a photocell utilized in conjunction with the push rod to measure the length of the row of fuel pellets inserted in the fuel rod

Control rod shutdown system

International Nuclear Information System (INIS)

Miyamoto, Yoshiyuki; Higashigawa, Yuichi.

1996-01-01

The present invention provides a control rod terminating system in a BWR type nuclear power plant, which stops an induction electric motor as rapidly as possible to terminate the control rods. Namely, the control rod stopping system controls reactor power by inserting/withdrawing control rods into a reactor by driving them by the induction electric motor. The system is provided with a control device for controlling the control rods and a control device for controlling the braking device. The control device outputs a braking operation signal for actuating the braking device during operation of the control rods to stop the operation of the control rods. Further, the braking device has at least two kinds of breaks, namely, a first and a second brakes. The two kinds of brakes are actuated by receiving the brake operation signals at different timings. The brake device is used also for keeping the control rods after the stopping. Even if a stopping torque of each of the breaks is small, different two kinds of brakes are operated at different timings thereby capable of obtaining a large stopping torque as a total. (I.S.)

Evaluation of the roughness of a crystal surface by X-ray scattering. Pt. 1

International Nuclear Information System (INIS)

Harada, Jimpei

1992-01-01

The relationship between the intensity distributions of the crystal truncation rod (CTR) scattering and the surface roughness of a crystal is discussed by developing a kinematic theory for the CTR scattering so as to reflect the two-dimensional aspect of the surface. The intensity of the CTR scattering elongated from a Bragg point is shown to be reduced by a factor vertical strokeΓ(q)vertical stroke 2 for a surface possessing some roughness, where Γ(q) is defined by a simple Fourier summation of γ p , the relative area with the same step height p on a surface, i.e. Γ(q) = Σ ∞ p=o γ p exp (2πipq), with Σ p γ p = 1, q being the distance in reciprocal space from the Bragg point along the CTR scattering. A pair-correlation function between the steps can, therefore, be obtained by a simple Fourier integral of the roughness damping factor vertical strokeΓ(q)vertical stroke 2 . For the case where γ p has a Gaussian distribution around the average step height, vertical strokeΓ(q)vertical stroke 2 is approximated by the well known Debye-Waller-like factor, exp (K- 4π 2 (Δp 2 )q 2 ), where (Δp 2 ) is the mean square deviation of step height in units of the lattice spacing. The intensity formulae proposed so far by several authors are also discussed on the basis of the above factor. (orig.)

New Schemes for Positive Real Truncation

Directory of Open Access Journals (Sweden)

Kari Unneland

2007-07-01

Full Text Available Model reduction, based on balanced truncation, of stable and of positive real systems are considered. An overview over some of the already existing techniques are given: Lyapunov balancing and stochastic balancing, which includes Riccati balancing. A novel scheme for positive real balanced truncation is then proposed, which is a combination of the already existing Lyapunov balancing and Riccati balancing. Using Riccati balancing, the solution of two Riccati equations are needed to obtain positive real reduced order systems. For the suggested method, only one Lyapunov equation and one Riccati equation are solved in order to obtain positive real reduced order systems, which is less computationally demanding. Further it is shown, that in order to get positive real reduced order systems, only one Riccati equation needs to be solved. Finally, this is used to obtain positive real frequency weighted balanced truncation.

Fuel rod leak detector

International Nuclear Information System (INIS)

Womack, R.E.

1978-01-01

A typical embodiment of the invention detects leaking fuel rods by means of a radiation detector that measures the concentration of xenon-133 ( 133 Xe) within each individual rod. A collimated detector that provides signals related to the energy of incident radiation is aligned with one of the ends of a fuel rod. A statistically significant sample of the gamma radiation (γ-rays) that characterize 133 Xe is accumulated through the detector. The data so accumulated indicates the presence of a concentration of 133 Xe appropriate to a sound fuel rod, or a significantly different concentration that reflects a leaking fuel rod

Crystallization and preliminary X-ray analysis of eukaryotic initiation factor 4E from Pisum sativum

International Nuclear Information System (INIS)

Ashby, Jamie A.; Stevenson, Clare E. M.; Maule, Andrew J.; Lawson, David M.

2009-01-01

Crystals of N-terminally truncated eIF4E from pea were obtained and X-ray data were recorded in-house to a resolution of 2.2 Å. Crystals of an N-terminally truncated 20 kDa fragment of Pisum sativum eIF4E (ΔN-eIF4E) were grown by vapour diffusion. X-ray data were recorded to a resolution of 2.2 Å from a single crystal in-house. Indexing was consistent with primitive monoclinic symmetry and solvent-content estimations suggested that between four and nine copies of the eIF4E fragment were possible per crystallographic asymmetric unit. eIF4E is an essential component of the eukaryotic translation machinery and recent studies have shown that point mutations of plant eIF4Es can confer resistance to potyvirus infection

Fuel rods

International Nuclear Information System (INIS)

Hattori, Shinji; Kajiwara, Koichi.

1980-01-01

Purpose: To ensure the safety for the fuel rod failures by adapting plenum springs to function when small forces such as during transportation of fuel rods is exerted and not to function the resilient force when a relatively great force is exerted. Constitution: Between an upper end plug and a plenum spring in a fuel rod, is disposed an insertion member to the lower portion of which is mounted a pin. This pin is kept upright and causes the plenum spring to function resiliently to the pellets against the loads due to accelerations and mechanical vibrations exerted during transportation of the fuel rods. While on the other hand, if a compression force of a relatively high level is exerted to the plenum spring during reactor operation, the pin of the insertion member is buckled and the insertion member is inserted to the inside of the plenum spring, whereby the pellets are allowed to expand freely and the failures in the fuel elements can be prevented. (Moriyama, K.)

Measuring a Truncated Disk in Aquila X-1

Science.gov (United States)

King, Ashley L.; Tomsick, John A.; Miller, Jon M.; Chenevez, Jerome; Barret, Didier; Boggs, Steven E.; Chakrabarty, Deepto; Christensen, Finn E.; Craig, William W.; Feurst, Felix;

Evolution of truncated moments of singlet parton distributions

International Nuclear Information System (INIS)

Forte, S.; Magnea, L.; Piccione, A.; Ridolfi, G.

2001-01-01

We define truncated Mellin moments of parton distributions by restricting the integration range over the Bjorken variable to the experimentally accessible subset x 0 ≤x≤1 of the allowed kinematic range 0≤x≤1. We derive the evolution equations satisfied by truncated moments in the general (singlet) case in terms of an infinite triangular matrix of anomalous dimensions which couple each truncated moment to all higher moments with orders differing by integers. We show that the evolution of any moment can be determined to arbitrarily good accuracy by truncating the system of coupled moments to a sufficiently large but finite size, and show how the equations can be solved in a way suitable for numerical applications. We discuss in detail the accuracy of the method in view of applications to precision phenomenology

All-dielectric rod antenna array for terahertz communications

Science.gov (United States)

Withayachumnankul, Withawat; Yamada, Ryoumei; Fujita, Masayuki; Nagatsuma, Tadao

2018-05-01

The terahertz band holds a potential for point-to-point short-range wireless communications at sub-terabit speed. To realize this potential, supporting antennas must have a wide bandwidth to sustain high data rate and must have high gain and low dissipation to compensate for the free space path loss that scales quadratically with frequency. Here we propose an all-dielectric rod antenna array with high radiation efficiency, high gain, and wide bandwidth. The proposed array is integral to a low-loss photonic crystal waveguide platform, and intrinsic silicon is the only constituent material for both the antenna and the feed to maintain the simplicity, compactness, and efficiency. Effective medium theory plays a key role in the antenna performance and integrability. An experimental validation with continuous-wave terahertz electronic systems confirms the minimum gain of 20 dBi across 315-390 GHz. A demonstration shows that a pair of such identical rod array antennas can handle bit-error-free transmission at the speed up to 10 Gbit/s. Further development of this antenna will build critical components for future terahertz communication systems.

Nanostructure of self-assembled rod-coil block copolymer films for photovoltaic applications

International Nuclear Information System (INIS)

Heiser, T.; Adamopoulos, G.; Brinkmann, M.; Giovanella, U.; Ould-Saad, S.; Brochon, C.; Wetering, K. van de; Hadziioannou, G.

2006-01-01

The nanostructures of a series of rod-coil block copolymers, designed for photovoltaic applications, are studied by atomic force microscopy and transmission electron microscopy. The copolymers are composed of a semiconducting poly-p-phenylenevinylene rod with (2'-ethyl)-hexyloxy side chains and a functionalized coil block of various length and flexibility. Both, as deposited and annealed block copolymer films were investigated. The results show that highly ordered structures are only obtained if the coil block is characterized by a glass transition temperature which is significantly lower than the melting temperature of the alkyl side chains. For this material a high molecular mobility and strong driving force for crystallization of the rigid block can be achieved simultaneously. For the smallest coil to rod length ratio, we found a lamellar morphology with perpendicularly oriented lamellae with respect to the substrate. Electron diffraction data show the presence of a periodical molecular arrangement with a characteristic distance of 0.94 nm that is attributed to the distance between conjugated chains separated by the layers of alkyl sidechains

Nanostructure of self-assembled rod-coil block copolymer films for photovoltaic applications

Energy Technology Data Exchange (ETDEWEB)

Heiser, T. [Institut d' Electronique du Solide et des Systemes (InESS), CNRS/ULP, 23, rue du Loess, F-67037 Strasbourg Cedex 2 (France)]. E-mail: Thomas.Heiser@iness.c-strasbourg.fr; Adamopoulos, G. [Laboratoire d' Ingenierie des Polymeres pour les Hautes Technologies (LIPHT), Ecole Europeenne de Chimie Polymeres et Materiaux (ECPM), 25, rue Becquerel, F-67087 Strasbourg Cedex 2 (France); Brinkmann, M. [Institut Charles Sadron (ICS), CNRS, 6, rue Boussingault, F-67083 Strasbourg Cedex (France); Giovanella, U. [Laboratoire d' Ingenierie des Polymeres pour les Hautes Technologies (LIPHT), Ecole Europeenne de Chimie Polymeres et Materiaux (ECPM), 25, rue Becquerel, F-67087 Strasbourg Cedex 2 (France); Ould-Saad, S. [Institut d' Electronique du Solide et des Systemes (InESS), CNRS/ULP, 23, rue du Loess, F-67037 Strasbourg Cedex 2 (France); Brochon, C. [Laboratoire d' Ingenierie des Polymeres pour les Hautes Technologies (LIPHT), Ecole Europeenne de Chimie Polymeres et Materiaux (ECPM), 25, rue Becquerel, F-67087 Strasbourg Cedex 2 (France); Wetering, K. van de [Laboratoire d' Ingenierie des Polymeres pour les Hautes Technologies (LIPHT), Ecole Europeenne de Chimie Polymeres et Materiaux (ECPM), 25, rue Becquerel, F-67087 Strasbourg Cedex 2 (France); Hadziioannou, G. [Laboratoire d' Ingenierie des Polymeres pour les Hautes Technologies (LIPHT), Ecole Europeenne de Chimie Polymeres et Materiaux (ECPM), 25, rue Becquerel, F-67087 Strasbourg Cedex 2 (France)

2006-07-26

The nanostructures of a series of rod-coil block copolymers, designed for photovoltaic applications, are studied by atomic force microscopy and transmission electron microscopy. The copolymers are composed of a semiconducting poly-p-phenylenevinylene rod with (2'-ethyl)-hexyloxy side chains and a functionalized coil block of various length and flexibility. Both, as deposited and annealed block copolymer films were investigated. The results show that highly ordered structures are only obtained if the coil block is characterized by a glass transition temperature which is significantly lower than the melting temperature of the alkyl side chains. For this material a high molecular mobility and strong driving force for crystallization of the rigid block can be achieved simultaneously. For the smallest coil to rod length ratio, we found a lamellar morphology with perpendicularly oriented lamellae with respect to the substrate. Electron diffraction data show the presence of a periodical molecular arrangement with a characteristic distance of 0.94 nm that is attributed to the distance between conjugated chains separated by the layers of alkyl sidechains.

Multiple fuel rod gripper

International Nuclear Information System (INIS)

Shields, E.P.

1987-01-01

An apparatus is described for gripping an array of rods comprising: (a) gripping members grippingly engageable with the rods, each of which has a hollow portion terminating in an open end for receiving the end of one of the rods; (b) a closing means for causing the hollow portion of each of the gripping members to apply substantially the same gripping force onto the end of its respective rod, including (i) a locking plate having a plurality of tapered holes registrable with the array of rods, wherein the exterior of each of the gripping members is tapered and nested within one of the tapered holes, (ii) a withdrawing means having a hydraulic plunger operatively connected to each of the gripping members for applying a substantially identical withdrawing force on each of the gripping members, whereby the hollow portion of each of the gripping members applies substantially the same gripping force on its respective rod, and (c) means for detecting whether each of the gripping members has grippingly engaged its respective rod

High-yield production of hydrophobins RodA and RodB from Aspergillus fumigatus in Pichia pastoris

DEFF Research Database (Denmark)

Pedersen, Mona Højgaard; Borodina, Irina; Moresco, Jacob Lange

2011-01-01

A as well as rRodB were able to convert a glass surface from hydrophilic to hydrophobic similar to native RodA, but only rRodB was able to decrease the hydrophobicity of a Teflon-like surface to the same extent as native RodA, while rRodA showed this ability to a lesser extent. Recombinant RodA and native...

Superconducting glass-ceramics in BiSrCaCu2Al0.5Ox---Comparison between rod and powder compacted specimens

International Nuclear Information System (INIS)

Hirata, K.; Abe, Y.

1991-01-01

Superconducting properties are studied for glass-ceramics which were prepared by reheating glass rods and the glass powder compacts in the BiSrCaCu 2 Al 0.5 O x system, respectively. The glass-ceramic rod specimens obtained by reheating rod glass at 800--830 degree C for 50 h have a T c (R=0) of 85 K, while the disk specimens obtained by reheating the powered glass compacts in the same way do not exhibit superconductivity above 77 K. This difference in superconductivity between the specimens is discussed in terms of crystallization process and the amount of oxygen absorption of the specimens during heating

Silicon crystal growth using a liquid-feeding Czochralski method

Science.gov (United States)

Shiraishi, Yutaka; Kurosaka, Shoei; Imai, Masato

1996-09-01

Silicon single crystals with uniformity along the growth direction were grown using a new continuous Czochralski (CCZ) method. Polycrystalline silicon rods used as charge materials are melted by carbon heaters over a crucible without contact between the raw material and other substances. Using this method, silicon crystals with diameters as large as 6 or 8 inch and good uniformity along the growth direction were grown.

Non-parametric order statistics method applied to uncertainty propagation in fuel rod calculations

International Nuclear Information System (INIS)

Arimescu, V.E.; Heins, L.

2001-01-01

Advances in modeling fuel rod behavior and accumulations of adequate experimental data have made possible the introduction of quantitative methods to estimate the uncertainty of predictions made with best-estimate fuel rod codes. The uncertainty range of the input variables is characterized by a truncated distribution which is typically a normal, lognormal, or uniform distribution. While the distribution for fabrication parameters is defined to cover the design or fabrication tolerances, the distribution of modeling parameters is inferred from the experimental database consisting of separate effects tests and global tests. The final step of the methodology uses a Monte Carlo type of random sampling of all relevant input variables and performs best-estimate code calculations to propagate these uncertainties in order to evaluate the uncertainty range of outputs of interest for design analysis, such as internal rod pressure and fuel centerline temperature. The statistical method underlying this Monte Carlo sampling is non-parametric order statistics, which is perfectly suited to evaluate quantiles of populations with unknown distribution. The application of this method is straightforward in the case of one single fuel rod, when a 95/95 statement is applicable: 'with a probability of 95% and confidence level of 95% the values of output of interest are below a certain value'. Therefore, the 0.95-quantile is estimated for the distribution of all possible values of one fuel rod with a statistical confidence of 95%. On the other hand, a more elaborate procedure is required if all the fuel rods in the core are being analyzed. In this case, the aim is to evaluate the following global statement: with 95% confidence level, the expected number of fuel rods which are not exceeding a certain value is all the fuel rods in the core except only a few fuel rods. In both cases, the thresholds determined by the analysis should be below the safety acceptable design limit. An indirect

Crystallization and preliminary X-ray crystallographic analysis of Aquifex aeolicus SelA, a bacterial selenocysteine synthase

International Nuclear Information System (INIS)

Itoh, Yuzuru; Sekine, Shun-ichi; Yokoyama, Shigeyuki

2012-01-01

The bacterial selenocysteine synthase SelA from Aquifex aeolicus was crystallized and the diffraction resolution was improved by lysine-residue methylation, truncation of N-terminal region (ΔN), and Lys-to-Ala point mutations. Phases were determined by using a selenomethionine-substituted crystal of the ΔN mutant. Selenocysteine (Sec), the 21st amino acid, is synthesized on its specific tRNA (tRNA Sec ) via a multi-step process. In bacteria, tRNA Sec is ligated first with serine by seryl-tRNA synthetase, which is followed by Ser-to-Sec conversion by Sec synthase (SelA). To elucidate its structure and catalytic mechanism, Aquifex aeolicus SelA was crystallized. Although wild-type SelA crystals diffracted X-rays poorly (to up to 8 Å resolution), the resolution was improved by introducing a quadruple point mutation targeting the loop regions and by methylating the lysine residues, which yielded 3.9 Å resolution diffraction data from a full-length SelA crystal. Truncation of the N-terminal region (ΔN) also improved the resolution. A 3.3 Å resolution data set for phase determination was obtained from a crystal of selenomethionine-substituted Lys-methylated SelA-ΔN

Three-Rod Resonator for Krypton Lamp Pumped 1.8 kW Continuous-Wave Nd:YAG Laser

Institute of Scientific and Technical Information of China (English)

LI Qiang; FANG Ming-Xing; WANG Zhi-Yong; YU Zhen-Sheng; LEI Hong; GUO Jiang; LI Gang; ZUO Tie-Chuan

2004-01-01

@@ A three-rod series resonator cw Nd:YAG laser suitable for the industrial applications is presented. The symmetrical resonator laser has been developed and is rated at 1820-W output power with beam parameter product 24 mm.mrad. By utilizing the symmetrical resonator design, the characteristic of beam with multi-rod is not obviously decreased compared with that of a single one. The system total electro-optics efficiency of lamp pumped YAG crystal is as high as 4.0%. The main factors, which affect output power and beam quality of high power solid-state laser module, are theoretically analysed.

Cone dystrophy with "supernormal" rod ERG: psychophysical testing shows comparable rod and cone temporal sensitivity losses with no gain in rod function.

Science.gov (United States)

Stockman, Andrew; Henning, G Bruce; Michaelides, Michel; Moore, Anthony T; Webster, Andrew R; Cammack, Jocelyn; Ripamonti, Caterina

2014-02-10

We report a psychophysical investigation of 5 observers with the retinal disorder "cone dystrophy with supernormal rod ERG," caused by mutations in the gene KCNV2 that encodes a voltage-gated potassium channel found in rod and cone photoreceptors. We compared losses for rod- and for cone-mediated vision to further investigate the disorder and to assess whether the supernormal ERG is associated with any visual benefit. L-cone, S-cone, and rod temporal acuity (critical flicker fusion frequency) were measured as a function of target irradiance; L-cone temporal contrast sensitivity was measured as a function of temporal frequency. Temporal acuity measures revealed that losses for vision mediated by rods, S-cones, and L-cones are roughly equivalent. Further, the gain in rod function implied by the supernormal ERG provides no apparent benefit to near-threshold rod-mediated visual performance. The L-cone temporal contrast sensitivity function in affected observers was similar in shape to the mean normal function but only after the mean function was compressed by halving the logarithmic sensitivities. The name of this disorder is potentially misleading because the comparable losses found across rod and cone vision suggest that the disorder is a generalized cone-rod dystrophy. Temporal acuity and temporal contrast sensitivity measures are broadly consistent with the defect in the voltage-gated potassium channel producing a nonlinear distortion of the photoreceptor response but after otherwise normal transduction processes.

Data and performance profiles applying an adaptive truncation criterion, within linesearch-based truncated Newton methods, in large scale nonconvex optimization

Directory of Open Access Journals (Sweden)

Andrea Caliciotti

2018-04-01

Full Text Available In this paper, we report data and experiments related to the research article entitled “An adaptive truncation criterion, for linesearch-based truncated Newton methods in large scale nonconvex optimization” by Caliciotti et al. [1]. In particular, in Caliciotti et al. [1], large scale unconstrained optimization problems are considered by applying linesearch-based truncated Newton methods. In this framework, a key point is the reduction of the number of inner iterations needed, at each outer iteration, to approximately solving the Newton equation. A novel adaptive truncation criterion is introduced in Caliciotti et al. [1] to this aim. Here, we report the details concerning numerical experiences over a commonly used test set, namely CUTEst (Gould et al., 2015 [2]. Moreover, comparisons are reported in terms of performance profiles (Dolan and Moré, 2002 [3], adopting different parameters settings. Finally, our linesearch-based scheme is compared with a renowned trust region method, namely TRON (Lin and Moré, 1999 [4].

Quartz substrate infrared photonic crystal

Science.gov (United States)

Ghadiri, Khosrow; Rejeb, Jalel; Vitchev, Vladimir N.

2003-01-01

This paper presents the fabrication of a planar photonic crystal (p2c) made of a square array of dielectric rods embedded in air, operating in the infrared spectrum. A quartz substrate is employed instead of the commonly used silicon or column III-V substrate. Our square structure has a normalized cylinder radius-to-pitch ratio of r/a = 0.248 and dielectric material contrast ɛr of 4.5. We choose a Z-cut synthetic quartz for its cut (geometry), and etching properties. Then a particular Z-axis etching process is employed in order to ensure the sharp-edged verticality of the rods and fast etching speed. We also present the computer simulations that allowed the establishment of the photonic band gaps (PBG) of our photonic crystal, as well as the actual measurements. An experimental measurement have been carried out and compared with different simulations. It was found that experimental results are in good agreement with different simulation results. Finally, a frequency selective device for optical communication based on the introduction of impurity sites in the photonic crystal is presented. With our proposed structure Optical System on a Chip (OsoC) with micro-cavity based active devices such as lasers, diodes, modulators, couplers, frequency selective emitters, add-drop filters, detectors, mux/demuxes and polarizers connected by passive waveguide links can be realized.

Conditional truncated plurigaussian simulation; Simulacao plurigaussiana truncada com condicionamento

Energy Technology Data Exchange (ETDEWEB)

Simon, Vitor Hugo

1997-12-01

The goal of this work was a development of an algorithm for the Truncated Plurigaussian Stochastic Simulation and its validation in a complex geologic model. The reservoir data comes from Aux Vases Zone at Rural Hill Field in Illinois, USA, and from the 2D geological interpretation, described by WEIMER et al. (1982), three sets of samples, with different grid densities ware taken. These sets were used to condition the simulation and to refine the estimates of the non-stationary matrix of facies proportions, used to truncate the gaussian random functions (RF). The Truncated Plurigaussian Model is an extension of the Truncated Gaussian Model (TG). In this new model its possible to use several facies with different spatial structures, associated with the simplicity of TG. The geological interpretation, used as a validation model, was chosen because it shows a set of NW/SE elongated tidal channels cutting the NE/SW shoreline deposits interleaved by impermeable facies. These characteristics of spatial structures of sedimentary facies served to evaluate the simulation model. Two independent gaussian RF were used, as well as an 'erosive model' as the truncation strategy. Also, non-conditional simulations were proceeded, using linearly combined gaussian RF with varying correlation coefficients. It was analyzed the influence of some parameters like: number of gaussian RF,correlation coefficient, truncations strategy, in the outcome of simulation, and also the physical meaning of these parameters under a geological point of view. It was showed, step by step, using an example, the theoretical model, and how to construct an algorithm to simulate with the Truncated Plurigaussian Model. The conclusion of this work was that even with a plain algorithm of the Conditional Truncated Plurigaussian and a complex geological model it's possible to obtain a usefulness product. (author)

Control rod drive for vertical movement

International Nuclear Information System (INIS)

Suskov, I.I.; Gorjunov, V.S.; Zajcev, B.I.; Derevjankin, N.E.; Petrov, V.A.; Istomin, S.D.; Kovalencik, D.I.; Archipov, E.A.; Serebrjakov, V.I.; Kacalin, V.S.

1982-01-01

The control of the rod repositioning gear unit and the control unit of the profile grab of the control rod drive for the alkali metal-cooled fast breeder reactor is achieved by an electromotor being arranged outside the hermetic drive casing. The guide tube is directly repositioned by the rod repositioning gear unit. Coupling control of the drive with the control rod is done in the lower operative position of the control rod and that because of the interaction of the tie rod arranged on the spring-mounted control rod with the induction transmitter for the lower position of the control rod. In the transfer position the rod is fixed within the guide tube. (orig.)

Safety rod driving device

International Nuclear Information System (INIS)

Murakami, Kiyonobu; Kurosaki, Akira.

1988-01-01

Purpose: To rapidly insert safety rods for a criticality experiment device into a reactor core container to stop the criticality reaction thereby prevent reactivity accidents. Constitution: A cylinder device having a safety rod as a cylinder rod attached with a piston at one end is constituted. The piston is elevated by pressurized air and attracted and fixed by an electromagnet which is a stationary device disposed at the upper portion of the cylinder. If the current supply to the electromagnet is disconnected, the safety rod constituting the cylinder rod is fallen together with the piston to the lower portion of the cylinder. Since the cylinder rod driving device has neither electrical motor nor driving screw as in the conventional device, necessary space can be reduced and the weight is decreased. In addition, since the inside of the nuclear reactor can easily be shielded completely from the external atmosphere, leakage of radioactive materials can be prevented. (Horiuchi, T.)

Purification, crystallization and preliminary X-ray characterization of a haemagglutinin from the seeds of Jatropha curcas

International Nuclear Information System (INIS)

Nair, Divya N.; Suresh, C. G.; Singh, Desh Deepak

2011-01-01

A novel haemagglutinin from Jatropha curcas seeds is purified and crystallized. X-ray diffraction data collected from the rod-shaped crystals were processed in the orthorhombic space group P2 1 2 1 2 1 and the crystals diffracted to 2.8 Å resolution at 103 K. The plant Jatropha curcas (Euphorbiaceae) is an important source of biofuel from the inedible oil present in its toxic seeds. The toxicity arises from the presence of curcin, a ribosome-inactivating protein showing haemagglutination activity. In this communication, the purification, crystallization and preliminary X-ray characterization are reported of a small protein isolated from J. curcas seeds with a molecular mass of ∼10 kDa that agglutinates rabbit erythrocytes. The protein was crystallized using the hanging-drop vapour-diffusion method and also by the microbatch method in 72-well HLA plates, using PEG 8000 as the precipitant in both conditions. X-ray diffraction data collected from the rod-shaped crystals were processed in the orthorhombic space group P2 1 2 1 2 1 . The crystals diffracted to 2.8 Å resolution at 103 K

Truncation in diffraction pattern analysis. Pt. 1

International Nuclear Information System (INIS)

Delhez, R.; Keijser, T.H. de; Mittemeijer, E.J.; Langford, J.I.

1986-01-01

An evaluation of the concept of a line profile is provoked by truncation of the range of intensity measurement in practice. The measured truncated line profile can be considered either as part of the total intensity distribution which peaks at or near the reciprocal-lattice points (approach 1), or as part of a component line profile which is confined to a single reciprocal-lattice point (approach 2). Some false conceptions in line-profile analysis can then be avoided and recipes can be developed for the extrapolation of the tails of the truncated line profile. Fourier analysis of line profiles, according to the first approach, implies a Fourier series development of the total intensity distribution defined within [l - 1/2, l + 1/2] (l indicates the node considered in reciprocal space); the second approach implies a Fourier transformation of the component line profile defined within [ - ∞, + ∞]. Exact descriptions of size broadening are provided by both approaches, whereas combined size and strain broadening can only be evaluated adequately within the first approach. Straightforward methods are given for obtaining truncation-corrected values for the average crystallite size. (orig.)

Crystallization and preliminary X-ray crystallographic analysis of human PACSIN 1 protein

International Nuclear Information System (INIS)

Bai, Xiaoyun; Meng, Geng; Li, Guoming; Luo, Ming; Zheng, Xiaofeng

2009-01-01

A C-terminal truncation construct of human PACSIN 1 (1–344) has been purified and crystallized. Diffraction data were collected to 3.0 Å resolution. PACSIN 1, which is mainly detected in brain tissue, is one of the PACSIN-family proteins involved in endocytosis and recruitment of synaptic vesicles. It binds to dynamin, synaptojanin 1 and N-WASP, and functions in vesicle formation and transport. However, the mechanisms of action of PACSIN 1 in these processes are largely unknown. Here, full-length and five C-terminal truncation constructs of human PACSIN 1 have been successfully expressed and purified in Escherichia coli. PACSIN 1 (1–344) was crystallized and diffracted to a resolution of 3.0 Å. The crystal belonged to space group C2, with unit-cell parameters a = 158.65, b = 87.38, c = 91.76 Å, α = 90.00, β = 113.61, γ = 90.00°. There were two molecules in the asymmetric unit and the solvent content was estimated to be about 70.47%

Self-organisation of semi-flexible rod-like particles

Science.gov (United States)

de Braaf, Bart; Oshima Menegon, Mariana; Paquay, Stefan; van der Schoot, Paul

2017-12-01

We report on a comprehensive computer simulation study of the liquid-crystal phase behaviour of purely repulsive, semi-flexible rod-like particles. For the four aspect ratios we consider, the particles form five distinct phases depending on their packing fraction and bending flexibility: the isotropic, nematic, smectic A, smectic B, and crystal phase. Upon increasing the particle bending flexibility, the various phase transitions shift to larger packing fractions. Increasing the aspect ratio achieves the opposite effect. We find two different ways in which the layer thickness of the particles in the smectic A phase may respond to an increase in concentration. The layer thickness may either decrease or increase depending on the aspect ratio and flexibility. For the smectic B and the crystalline phases, increasing the concentration always decreases the layer thickness. Finally, we find that the layer spacing jumps to a larger value on transitioning from the smectic A phase to the smectic B phase.

Testing device for control rod drives

International Nuclear Information System (INIS)

Hayakawa, Toshifumi.

1992-01-01

A testing device for control rod drives comprises a logic measuring means for measuring an output signal from a control rod drive logic generation circuit, a control means for judging the operation state of a control rod and a man machine interface means for outputting the result of the judgement. A driving instruction outputted from the control rod operation device is always monitored by the control means, and if the operation instruction is stopped, a testing signal is outputted to the control rod control device to simulate a control rod operation. In this case, the output signal of the control rod drive logic generation circuit is held in a control rod drive memory means and intaken into a logic analysis means for measurement and an abnormality is judged by the control means. The stopping of the control rod drive instruction is monitored and the operation abnormality of the control rod is judged, to mitigate the burden of an operator. Further, the operation of the control rod drive logic generation circuit can be confirmed even during a nuclear plant operation by holding the control rod drive instruction thereby enabling to improve maintenance efficiency. (N.H.)

Performance study of highly efficient 520 W average power long pulse ceramic Nd:YAG rod laser

Science.gov (United States)

Choubey, Ambar; Vishwakarma, S. C.; Ali, Sabir; Jain, R. K.; Upadhyaya, B. N.; Oak, S. M.

2013-10-01

We report the performance study of a 2% atomic doped ceramic Nd:YAG rod for long pulse laser operation in the millisecond regime with pulse duration in the range of 0.5-20 ms. A maximum average output power of 520 W with 180 J maximum pulse energy has been achieved with a slope efficiency of 5.4% using a dual rod configuration, which is the highest for typical lamp pumped ceramic Nd:YAG lasers. The laser output characteristics of the ceramic Nd:YAG rod were revealed to be nearly equivalent or superior to those of high-quality single crystal Nd:YAG rod. The laser pump chamber and resonator were designed and optimized to achieve a high efficiency and good beam quality with a beam parameter product of 16 mm mrad (M2˜47). The laser output beam was efficiently coupled through a 400 μm core diameter optical fiber with 90% overall transmission efficiency. This ceramic Nd:YAG laser will be useful for various material processing applications in industry.

Preparation and characterization of superfine ammonium perchlorate (AP) crystals through ceramic membrane anti-solvent crystallization

Science.gov (United States)

Ma, Zhenye; Li, Cheng; Wu, Rujun; Chen, Rizhi; Gu, Zhenggui

2009-10-01

In this paper, a novel ceramic membrane anti-solvent crystallization (CMASC) method was proposed for the safe and rapid preparation ammonium perchlorate (AP) crystals, in which the acetone and ethyl acetate were chosen as solvent and anti-solvent, respectively. Comparing with the conventional liquid anti-solvent crystallization (LASC), CMASC which successfully introduces ceramic membrane with regular pore structure to the LASC as feeding medium, is favorable to control the rate of feeding rate and, therefore, to obtain size and morphology controllable AP. Several kinds of micro-sized AP particles with different morphology were obtained including polyhedral-like, quadrate-like to rod-like. The effect of processing parameters on the crystal size and shape of AP crystals such as volume ratio of anti-solvent to solvent, feeding pressure and crystallization temperature were investigated. It is found that higher volume ratio of anti-solvent to solvent, higher feeding pressure and higher temperature result in smaller particle size. Scaning electron microscopy (SEM) and X-ray diffraction (XRD) were used to characterize the resulting AP crystals. The nucleation and growth kinetic of the resulting AP crystals were also discussed.

Control of calcium carbonate crystallization by using anionic polymethylsiloxanes as templates

Energy Technology Data Exchange (ETDEWEB)

Neira-Carrillo, Andronico, E-mail: aneira@uchile.cl [Faculty of Veterinary and Animal Sciences, University of Chile, Santa Rosa 11735, PO Box 2-15, Santiago (Chile); Vasquez-Quitral, Patricio; Paz Diaz, Maria; Soledad Fernandez, Maria; Luis Arias, Jose [Faculty of Veterinary and Animal Sciences, University of Chile, Santa Rosa 11735, PO Box 2-15, Santiago (Chile); Yazdani-Pedram, Mehrdad [Faculty of Chemical and Pharmaceutical Science, University of Chile, S. Livingstone 1007, PO Box 233, Santiago (Chile)

2012-10-15

Sulfonated (SO{sub 3}H-PMS) and carboxylated (CO{sub 2}H-PMS) polymethylsiloxanes were synthesized and their effects as anionic template modifier on the CaCO{sub 3} crystal morphologies were evaluated. In vitro crystallization assays of CaCO{sub 3} were performed at room temperature by using gas diffusion method at different concentration, pH and time. SEM images of CaCO{sub 3} showed well-defined short calcite piles (ca. 5 {mu}m) and elongated calcite (ca. 20 {mu}m) when SO{sub 3}H-PMS was used. When CO{sub 2}H-PMS was used, the morphology of CaCO{sub 3} crystals was single-truncated at pH 7-9 and aggregated-modified calcite at pH 10-11. However, at pH 12 the least stable donut-shaped vaterite crystals were formed. EDS and XRD confirmed the presence of Si from anionic PMS templates on the CaCO{sub 3} surfaces and its polymorphism, respectively. Results showed that the selective morphologies of CaCO{sub 3} reflect the electrostatic interaction of anionic groups of functionalized PMS with Ca{sup 2+} adsorbed on CaCO{sub 3} crystals. Rounded and truncated-modified fluorescent CaCO{sub 3} was also produced by the inclusion of functionalized PMS into the lattice of CaCO{sub 3} matrix. We demonstrated that the anionic PMS offer a good modifier for polymer-controlled crystallization and a convenient approach for understanding the biomineralization field. - Graphical abstract: Optical photographs of rounded and truncated-modified fluorescent CaCO{sub 3} produced by the inclusion of sulfonated (SO{sub 3}H-PMS) polymethylsiloxanes into the lattice of CaCO{sub 3} matrix. Insert represents the simulation of modified and fluorescent CaCO{sub 3} crystals using Software JCrystal, (2008). Highlights: Black-Right-Pointing-Pointer We prepared two anionic polymethylsiloxanes (PMS) as templates. Black-Right-Pointing-Pointer Their modifier capacity on the CaCO{sub 3} crystal morphologies was demonstrated. Black-Right-Pointing-Pointer At pH 12, the least stable donut-shaped vaterite

Truncation Depth Rule-of-Thumb for Convolutional Codes

Science.gov (United States)

Moision, Bruce

2009-01-01

In this innovation, it is shown that a commonly used rule of thumb (that the truncation depth of a convolutional code should be five times the memory length, m, of the code) is accurate only for rate 1/2 codes. In fact, the truncation depth should be 2.5 m/(1 - r), where r is the code rate. The accuracy of this new rule is demonstrated by tabulating the distance properties of a large set of known codes. This new rule was derived by bounding the losses due to truncation as a function of the code rate. With regard to particular codes, a good indicator of the required truncation depth is the path length at which all paths that diverge from a particular path have accumulated the minimum distance of the code. It is shown that the new rule of thumb provides an accurate prediction of this depth for codes of varying rates.

Investigation of propagation dynamics of truncated vector vortex beams.

Science.gov (United States)

Srinivas, P; Perumangatt, C; Lal, Nijil; Singh, R P; Srinivasan, B

2018-06-01

In this Letter, we experimentally investigate the propagation dynamics of truncated vector vortex beams generated using a Sagnac interferometer. Upon focusing, the truncated vector vortex beam is found to regain its original intensity structure within the Rayleigh range. In order to explain such behavior, the propagation dynamics of a truncated vector vortex beam is simulated by decomposing it into the sum of integral charge beams with associated complex weights. We also show that the polarization of the truncated composite vector vortex beam is preserved all along the propagation axis. The experimental observations are consistent with theoretical predictions based on previous literature and are in good agreement with our simulation results. The results hold importance as vector vortex modes are eigenmodes of the optical fiber.

Failed fuel rod detector

Energy Technology Data Exchange (ETDEWEB)

Uchida, Katsuya; Matsuda, Yasuhiko

1984-05-02

The purpose of the project is to enable failed fuel rod detection simply with no requirement for dismantling the fuel assembly. A gamma-ray detection section is arranged so as to attend on the optional fuel rods in the fuel assembly. The fuel assembly is adapted such that a gamma-ray shielding plate is detachably inserted into optional gaps of the fuel rods or, alternatively, the fuel assembly can detachably be inserted to the gamma-ray shielding plate. In this way, amount of gaseous fission products accumulated in all of the plenum portions in the fuel rods as the object of the measurement can be determined without dismantling the fuel assembly. Accordingly, by comparing the amounts of the gaseous fission products, the failed fuel rod can be detected.

RodPilotR - The Innovative and Cost-Effective Digital Control Rod Drive Control System for PWRs

International Nuclear Information System (INIS)

Baron, Clemens

2008-01-01

With RodPilot, AREVA NP offers an innovative and cost-effective system for controlling control rods in Pressurized Water Reactors. RodPilot controls the three operating coils of the control rod drive mechanism (lift, moveable gripper and stationary gripper coil). The rods are inserted into or withdrawn from the core as required by the Reactor Control System. The system combines modern components, state-of-the-art logic and a proven electronic control rod drive control principle to provide enhanced reliability and lower maintenance costs. (author)

Synthesis and morphology of AgReO{sub 4} plates, rods, and stars

Energy Technology Data Exchange (ETDEWEB)

Bruetsch, Lennart; Feldmann, Claus [Institut fuer Anorganische Chemie, Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany)

2017-07-03

AgReO{sub 4} nanoplates and micron-sized AgReO{sub 4} rods and stars are obtained for the first time from controlled particle growth in THF. [NBu{sub 4}][ReO{sub 4}] or [NMe{sub 4}][ReO{sub 4}] and Ag(OTf) (OTf: triflate) are used as the starting materials. The crystal growth is directed by the presence (i.e., plates) or absence (i.e., rods, stars) of trioctylphosphine (TOP) as a coordinating agent as well as by the temperature of the reaction (i.e., plates, rods in refluxing THF; stars at room temperature). Altogether, the growth of the respective morphology can be attributed to the availability and diffusion rate of dissolved Ag{sup +} that is influenced by the reaction temperature and the presence of TOP. The differently shaped AgReO{sub 4} particles are characterized by scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), and Fourier-transform infrared (FT-IR) spectroscopy. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Integrated control rod monitoring device

International Nuclear Information System (INIS)

Saito, Katsuhiro

1997-01-01

The present invention provides a device in which an entire control rod driving time measuring device and a control rod position support device in a reactor building and a central control chamber are integrated systematically to save hardwares such as a signal input/output device and signal cables between boards. Namely, (1) functions of the entire control rod driving time measuring device for monitoring control rods which control the reactor power and a control rod position indication device are integrated into one identical system. Then, the entire devices can be made compact by the integration of the functions. (2) The functions of the entire control rod driving time measuring device and the control rod position indication device are integrated in a central operation board and a board in the site. Then, the place for the installation of them can be used in common in any of the cases. (3) The functions of the entire control rod driving time measuring device and the control rod position indication device are integrated to one identical system to save hardware to be used. Then, signal input/output devices and drift branching panel boards in the site and the central operation board can be saved, and cables for connecting both of the boards is no more necessary. (I.S.)

Cloning, expression, purification, crystallization and preliminary X-ray analysis of the human RuvBL1–RuvBL2 complex

International Nuclear Information System (INIS)

Gorynia, Sabine; Matias, Pedro M.; Bandeiras, Tiago M.; Donner, Peter; Carrondo, Maria Arménia

2008-01-01

A truncated variant of the human RuvBL1–RuvBL2 complex was cloned, expressed, purified and crystallised. Synchrotron diffraction data to 4 Å resolution were used to carry out a preliminary crystallographic analysis of the complex. The complex of RuvBL1 and its homologue RuvBL2, two evolutionarily highly conserved eukaryotic proteins belonging to the AAA + (ATPase associated with diverse cellular activities) family of ATPases, was co-expressed in Escherichia coli. For crystallization purposes, the flexible domains II of RuvBL1 and RuvBL2 were truncated. The truncated RuvBL1–RuvBL2 complex was crystallized using the hanging-drop vapour-diffusion method at 293 K. The crystals were hexagonal-shaped plates and belonged to either the orthorhombic space group C222 1 , with unit-cell parameters a = 111.4, b = 188.0, c = 243.4 Å and six monomers in the asymmetric unit, or the monoclinic space group P2 1 , with unit-cell parameters a = 109.2, b = 243.4, c = 109.3 Å, β = 118.7° and 12 monomers in the asymmetric unit. The crystal structure could be solved by molecular replacement in both possible space groups and the solutions obtained showed that the complex forms a dodecamer

Cloning, expression, purification, crystallization and preliminary X-ray diffraction analysis of glyoxalase I from Leishmania infantum

International Nuclear Information System (INIS)

Barata, Lídia; Sousa Silva, Marta; Schuldt, Linda; Costa, Gonçalo da; Tomás, Ana M.; Ferreira, António E. N.; Weiss, Manfred S.; Ponces Freire, Ana; Cordeiro, Carlos

2010-01-01

Glyoxalase I from L. infantum was cloned, overexpressed in E. coli, purified and crystallized. Glyoxalase I (GLO1) is the first of the two glyoxalase-pathway enzymes. It catalyzes the formation of S-d-lactoyltrypanothione from the non-enzymatically formed hemithioacetal of methylglyoxal and reduced trypanothione. In order to understand its substrate binding and catalytic mechanism, GLO1 from Leishmania infantum was cloned, overexpressed in Escherichia coli, purified and crystallized. Two crystal forms were obtained: a cube-shaped form and a rod-shaped form. While the cube-shaped form did not diffract X-rays at all, the rod-shaped form exhibited diffraction to about 2.0 Å resolution. The crystals belonged to space group P2 1 2 1 2, with unit-cell parameters a = 130.03, b = 148.51, c = 50.63 Å and three dimers of the enzyme per asymmetric unit

Growth of binary solid solution single crystals and calculation of melt surface displacement velocity

International Nuclear Information System (INIS)

Agamaliyev, Z.A.; Tahirov, V.I.; Hasanov, Z.Y.; Quliyev, A.F.

2007-01-01

A binary solid solution single crystal growth method has been worked out. Cylinder feeding alloy with complex content distribution and truncated cone crucible are used. Second component distribution coefficient is more than unit. Content distribution along grown crystal is found by solving continuity equation. After reaching dynamic equilibrium state second component concentration in grown crystal is saturated the value of which is less than the average ona in the feeding alloy. Using the method Ge-Si perfect single crystals has been grown. Calculation method of melt surface displacement velocity has been offered as well

Rod drive and latching mechanism

International Nuclear Information System (INIS)

Veronesi, L.; Sherwood, D.G.

1982-01-01

Hydraulic drive and latching mechanisms for driving reactivity control mechanisms in nuclear reactors are described. Preferably, the pressurized reactor coolant is utilized to raise the drive rod into contact with and to pivot the latching mechanism so as to allow the drive rod to pass the latching mechanism. The pressure in the housing may then be equalized which allows the drive rod to move downwardly into contact with the latching mechanism but to hold the shaft in a raised position with respect to the reactor core. Once again, the reactor coolant pressure may be utilized to raise the drive rod and thus pivot the latching mechanism so that the drive rod passes above the latching mechanism. Again, the mechanism pressure can be equalized which allows the drive rod to fall and pass by the latching mechanism so that the drive rod approaches the reactor core. (author)

A third kind growth model of tetrapod: Rod-based single crystal ZnO tetrapod nanostructure

International Nuclear Information System (INIS)

Gong, J.F.; Huang, H.B.; Wang, Z.Q.; Zhao, X.N.; Yang, S.G.; Yu Zhongzhen

2008-01-01

In this paper, rod-based ZnO tetrapods were successfully synthesized by burning Zn particles in air covered with two firebricks. The products show hexagonal wurtzite phase. The microstructures of the tetrapod were studied carefully by scanning electron microscope (SEM), transmission electron microscope (TEM), SAED and HRTEM. The results show that tetrapod has single crystalline phase with one broader nanorod growing along [0 0 0 1] direction, three triangular nanosheets, growing out of the three trisection planes along [101-bar0] direction, and three epitaxial nanowires, growing from each tip of the triangular nanosheets. Based on the experimental results, a rod-based growth model was proposed to interpret its growth mechanism. Room temperature photoluminescence spectrum reveals that the ZnO tetrapods have ultra violet (UV) emission band (389 nm) and a green emission band (517 nm)

Control rods

International Nuclear Information System (INIS)

Koga, Isao; Masuoka, Ryuzo.

1979-01-01

Purpose: To prevent fuel element failures during power conditioning by removing liquid absorbents in poison tubes of control rods in a fast power up step and extracting control rods to slightly increase power in a medium power up step. Constitution: A plurality of poison tubes are disposed in a coaxial or plate-like arrangement and divided into a region capable of compensating the reactivity from the initial state at low temperature to 40% power operation and a region capable of compensating the reactivity in the power up above 40% power operation. Soluble poisons are used as absorbers in the poison tubes corresponding to above 40% power operation and they are adapted to be removed independently from the driving of control rods. The poison tubes filled with the soluble absorbers are responsible for the changes in the reactivity from the initial state at low temperature to the medium power region and the reactivity control is conducted by the elimination of liquid absorbers from the poison tubes. In the succeeding slight power up region above the medium power, power up is proceeding by extracting the control rods having remaining poison tubes filled with solid or liquid absorbers. (Seki, T.)

Simulation of nuclear fuel rods by using process computer-controlled power for indirect electrically heated rods

International Nuclear Information System (INIS)

Malang, S.

1975-11-01

An investigation was carried out to determine how the simulation of nuclear fuel rods with indirect electrically heated rods could be improved by use of a computer to control the electrical power during a loss-of-coolant accident (LOCA). To aid in the experiment, a new version of the HETRAP code was developed which simulates a LOCA with heater rod power controlled by a computer that adjusts rod power during a blowdown to minimize the difference in heat flux of the fuel and heater rods. Results show that without computer control of heater rod power, only the part of a blowdown up to the time when the heat transfer mode changes from nucleate boiling to transition or film boiling can be simulated well and then only for short times. With computer control, the surface heat flux and temperature of an electrically heated rod can be made nearly identical to that of a reactor fuel rod with the same cooling conditions during much of the LOCA. A small process control computer can be used to achieve close simulation of a nuclear fuel rod with an indirect electrically heated rod

Rapid thermal melted TiO2 nano-particles into ZnO nano-rod and its application for dye sensitized solar cells

International Nuclear Information System (INIS)

Chao, Ching-Hsun; Chang, Chi-Lung; Chan, Chien-Hung; Lien, Shui-Yang; Weng, Ko-Wei; Yao, Kuo-Shan

2010-01-01

TiO 2 nano-particles with an anchored ZnO nano-rod structure were synthesized using the hydrothermal method to grow ZnO nano-rods and coated TiO 2 nano-particles on ZnO nano-rods using the rapid thermal annealing method on ITO conducting glass pre-coated with nano porous TiO 2 film. The XRD study showed that there was little difference in crystal composition for various types of TiO 2 nano-particles anchored to ZnO nano-rods. The as-prepared architecture was characterized using field-emission scanning electron microscopy (FE-SEM). Films with TiO 2 nano-particles anchored to ZnO nano-rods were used as electrode materials to fabricate dye sensitized solar cells (DSSCs). The best solar energy conversion efficiency of 2.397% was obtained by modified electrode material, under AM 1.5 illumination, achieved up to J sc = 15.382 mA/cm 2 , V oc = 0.479 V and fill factor = 32.8%.

Fuel rod technology

International Nuclear Information System (INIS)

Bezold, H.; Romeiser, H.J.

1979-07-01

By extensive mechanization and automation of the fuel rod production, also at increasing production numbers, an efficient production shall be secured, simultaneously corresponding to the high quality standard of the fuel rods. The works done up to now concentrated on the lay out of a rough concept for a mechanized production course. Detail-studies were made for the problems of fuel rod humidity, filling and resistance welding. Further promotion of this project and thus further report will be stopped, since the main point of these works is the production technique. (orig.) [de

Comment on the consistency of truncated nonlinear integral equation based theories of freezing

International Nuclear Information System (INIS)

Cerjan, C.; Bagchi, B.; Rice, S.A.

1985-01-01

We report the results of two studies of aspects of the consistency of truncated nonlinear integral equation based theories of freezing: (i) We show that the self-consistent solutions to these nonlinear equations are unfortunately sensitive to the level of truncation. For the hard sphere system, if the Wertheim--Thiele representation of the pair direct correlation function is used, the inclusion of part but not all of the triplet direct correlation function contribution, as has been common, worsens the predictions considerably. We also show that the convergence of the solutions found, with respect to number of reciprocal lattice vectors kept in the Fourier expansion of the crystal singlet density, is slow. These conclusions imply great sensitivity to the quality of the pair direct correlation function employed in the theory. (ii) We show the direct correlation function based and the pair correlation function based theories of freezing can be cast into a form which requires solution of isomorphous nonlinear integral equations. However, in the pair correlation function theory the usual neglect of the influence of inhomogeneity of the density distribution on the pair correlation function is shown to be inconsistent to the lowest order in the change of density on freezing, and to lead to erroneous predictions

Investigation of the operating conditions to morphology evolution of β-L-glutamic acid during seeded cooling crystallization

Science.gov (United States)

Zhang, Fangkun; Liu, Tao; Huo, Yan; Guan, Runduo; Wang, Xue Z.

2017-07-01

In this paper the effects of operating conditions including cooling rate, initial supersaturation, and seeding temperature were investigated on the morphology evolution of β-L-glutamic acid (β-LGA) during seeded cooling crystallization. Based on the results of in-situ image acquisition of the crystal morphology evolution during the crystallization process, it was found that the crystal products tend to be plate-like or short rod-like under a slow cooling rate, low initial supersaturation, and low seeding temperature. In the opposite, the operating conditions of a faster cooling rate, higher initial supersaturation, and higher seeding temperature tend to produce long rod-like or needle-like crystals, and meanwhile, the length and width of crystal products will be increased together with a wider crystal size distribution (CSD). The aspect ratio of crystals, defined by the crystal length over width measured from in-situ or sample images, was taken as a shape index to analyze the crystal morphologies. Based on comparative analysis of the experimental results, guidelines on these operating conditions were given for obtaining the desired crystal shapes, along with the strategies for obtaining a narrower CSD for better product quality. Experimental verifications were performed to illustrate the proposed guidelines on the operating conditions for seeded cooling crystallization of LGA solution.

Wigner distribution function of circularly truncated light beams

NARCIS (Netherlands)

Bastiaans, M.J.; Nijhawan, O.P.; Gupta, A.K.; Musla, A.K.; Singh, Kehar

1998-01-01

Truncating a light beam is expressed as a convolution of its Wigner distribution function and the WDF of the truncating aperture. The WDF of a circular aperture is derived and an approximate expression - which is exact in the space and the spatial-frequency origin and whose integral over the spatial

Photonic band gap engineering in 2D photonic crystals

Indian Academy of Sciences (India)

-dimensional photonic crystals with square lattices composed of air holes in dielectric and vice versa i.e., dielectric rods in air, using the plane-wave expansion method are investigated. We then study, how the photonic band gap size is ...

Digital control rod blocking monitor

International Nuclear Information System (INIS)

Funayama, Yoshio.

1996-01-01

The present invention system is used for monitoring of a power region of a reactor, and used for monitoring of simultaneous withdrawal of a plurality of control rods without increasing the size or complicating the system. Namely, the system processes signals from a neutron flux detectors at the periphery of control rods controlled for withdrawal. As a result of the processing, the digital monitoring system generates an alarm when the reactor power at the periphery of the control rods fluctuates exceeding an allowable range. In the system, a control rod information forming means prepares frame data comprising front data, positions of the control rods to be withdrawn, frame numbers and completion data. A serial data transmitting means transmits the frame data successively as repeating frame data rows. A control rod information receiving means takes up the frame data of each of control rods to be withdrawn from the transmitted frame data rows. Since the system of the present invention can monitor the withdrawal of a plurality of control rods simultaneously without increasing the size or complicating the system, cost can be saved and the maintenance can be improved. (I.S.)

The effect of truncation on very small cardiac SPECT camera systems

International Nuclear Information System (INIS)

Rohmer, Damien; Eisner, Robert L.; Gullberg, Grant T.

2006-01-01

Background: The limited transaxial field-of-view (FOV) of a very small cardiac SPECT camera system causes view-dependent truncation of the projection of structures exterior to, but near the heart. Basic tomographic principles suggest that the reconstruction of non-attenuated truncated data gives a distortion-free image in the interior of the truncated region, but the DC term of the Fourier spectrum of the reconstructed image is incorrect, meaning that the intensity scale of the reconstruction is inaccurate. The purpose of this study was to characterize the reconstructed image artifacts from truncated data, and to quantify their effects on the measurement of tracer uptake in the myocardial. Particular attention was given to instances where the heart wall is close to hot structures (structures of high activity uptake).Methods: The MCAT phantom was used to simulate a 2D slice of the heart region. Truncated and non-truncated projections were formed both with and without attenuation. The reconstructions were analyzed for artifacts in the myocardium caused by truncation, and for the effect that attenuation has relative to increasing those artifacts. Results: The inaccuracy due to truncation is primarily caused by an incorrect DC component. For visualizing the left ventricular wall, this error is not worse than the effect of attenuation. The addition of a small hot bowel-like structure near the left ventricle causes few changes in counts on the wall. Larger artifacts due to the truncation are located at the boundary of the truncation and can be eliminated by sinogram interpolation. Finally,algebraic reconstruction methods are shown to give better reconstruction results than an analytical filtered back-projection reconstruction algorithm. Conclusion: Small inaccuracies in reconstructed images from small FOV camera systems should have little effect on clinical interpretation. However, changes in the degree of inaccuracy in counts from slice to slice are due to changes in

Seeded growth of InP and InAs quantum rods using indium acetate and myristic acid

International Nuclear Information System (INIS)

Shweky, Itzhak; Aharoni, Assaf; Mokari, Taleb; Rothenberg, Eli; Nadler, Moshe; Popov, Inna; Banin, Uri

2006-01-01

A synthesis of soluble III-V semiconductor quantum rods using gold nanoparticles to direct and catalyze one-dimensional growth is developed. The growth takes place via the solution-liquid-solid (SLS) mechanism where proper precursors are injected into a coordinating solvent. We report the synthesis of InP nanorods using indium acetate and myristic acid with gold nanoparticles as the catalysts in the SLS growth mode. A similar route was successfully developed for the growth of InAs nanorods. We find that the amount of Au catalyst in the reaction is an important parameter to achieve shape control. Transmission electron microscope (TEM) images of InP and InAs nanocrystals revealed that the crystals are mostly rod-shaped, and provide strong evidence for Au presence in one edge. The rods were characterized structurally using X-ray diffraction and high-resolution TEM and optically by absorption and photoluminescence

The BWR Hybrid 4 control rod

International Nuclear Information System (INIS)

Gross, H.; Fuchs, H.P.; Lippert, H.J.; Dambietz, W.

1988-01-01

The service life of BWR control rods designed in the past has been unsatisfactory. The main reason was irradiation assisted stress corrosion cracking of B 4 C rods caused by external swelling of the B 4 C powder. By this reason KWU developed an improved BWR control rod (Hybrid 4 control rod) with extended service life and increased control rod worth. It also allows the procedure for replacing and rearranging fuel assemblies to be considerably simplified. A complete set of Hydbrid 4 control rods is expected to last throughout the service life of a plant (assumption: ca. 40 years) if an appropriate control rod reshuffling management program is used. (orig.)

X-ray diffraction studies on merohedrally twinned Δ1–62NtNBCe1-A crystals of the sodium/bicarbonate cotransporter

International Nuclear Information System (INIS)

Gill, Harindarpal S.; Dutcher, Lauren; Boron, Walter F.; Patel, Samir; Guay-Woodford, Lisa M.

2013-01-01

A truncated mutant missing the first 62 residues of the N-terminal, cytoplasmic domain of the sodium-bicarbonate NBCe1-A cotransporter crystallizes in space group P3 1 with pseudo-P3 1 21 symmetry and a hemihedral twin fraction of 33.0%. Twinned fractions and twin-pair statistics over binned resolutions confirm that the calculated twin fraction is associated with hemihedral twinning and not to non-crystallographic symmetry. NBCe1-A membrane-embedded macromolecules that cotransport sodium and bicarbonate ions across the bilayer serve to maintain acid–base homeostasis throughout the body. Defects result in a number of renal and eye disorders, including type-II renal tubular acidosis and cataracts. Here, crystals of a human truncated mutant of the cytoplasmic N-terminal domain of NBCe1 (Δ1–62NtNBCe1-A) are reported that diffract X-rays to 2.4 Å resolution. The crystal symmetry of Δ1–62NtNBCe1-A is of space group P3 1 with pseudo-P3 1 21 symmetry and it has a hemihedral twin fraction of 33.0%. The crystals may provide insight into the pathogenic processes observed in a subset of patients with truncating and point mutations in the gene encoding NBCe1

Burnable poison rod

International Nuclear Information System (INIS)

Natsume, Tomohiro.

1988-01-01

Purpose: To decrease the effect of water elimination and the effect of burn-up residue boron, thereby reduce the effect of burnable poison rods as the neutron poisons at the final stage of reactor core lifetime. Constitution: In a burnable poison rod according to the present invention, a hollow burnable poison material is filled in an external fuel can, an inner fuel can mounted with a carbon rod is inserted to the hollow portion of the burnable poison material and helium gases are charged in the outer fuel can. In such a burnable poison rod, the reactivity worths after the burning are reduced to one-half as compared with the conventional case. Accordingly, since the effect of the burnable poison as the neutron poisons is reduced at the final stage of the reactor core of lifetime, the excess reactivity of the reactor core is increased. (Horiuchi, T.)

Zinc oxide nano-rods based glucose biosensor devices fabrication

Science.gov (United States)

Wahab, H. A.; Salama, A. A.; El Saeid, A. A.; Willander, M.; Nur, O.; Battisha, I. K.

2018-06-01

ZnO is distinguished multifunctional material that has wide applications in biochemical sensor devices. For extracellular measurements, Zinc oxide nano-rods will be deposited on conducting plastic substrate with annealing temperature 150 °C (ZNRP150) and silver wire with annealing temperature 250 °C (ZNRW250), for the extracellular glucose concentration determination with functionalized ZNR-coated biosensors. It was performed in phosphate buffer saline (PBS) over the range from 1 μM to 10 mM and on human blood plasma. The prepared samples crystal structure and surface morphologies were characterized by XRD and field emission scanning electron microscope FESEM respectively.

Biomechanics of lumbar cortical screw-rod fixation versus pedicle screw-rod fixation with and without interbody support.

Science.gov (United States)

Perez-Orribo, Luis; Kalb, Samuel; Reyes, Phillip M; Chang, Steve W; Crawford, Neil R

2013-04-15

Seven different combinations of posterior screw fixation, with or without interbody support, were compared in vitro using nondestructive flexibility tests. To study the biomechanical behavior of a new cortical screw (CS) fixation construct relative to the traditional pedicle screw (PS) construct. The CS is an alternative to the PS for posterior fixation of the lumbar spine. The CS trajectory is more sagittally and cranially oriented than the PS, being anchored in the pars interarticularis. Like PS fixation, CS fixation uses interconnecting rods fastened with top-locking connectors. Stability after bilateral CS fixation was compared with stability after bilateral PS fixation in the setting of intact disc and with direct lateral interbody fixation (DLIF) or transforaminal lateral interbody fixation (TLIF) support. Standard nondestructive flexibility tests were performed in cadaveric lumbar specimens, allowing non-paired comparisons of specific conditions from 28 specimens (4 groups of 7) within a larger experiment of multiple hardware configurations. Condition tested and group from which results originated were as follows: (1) intact (all groups); (2) with L3-L4 bilateral PS-rods (group 1); (3) with bilateral CS-rods (group 2); (4) with DLIF (group 3); (5) with DLIF + CS-rods (group 4); (6) with DLIF + PS-rods (group 3); (7) with TLIF + CS-rods (group 2), and (8) with TLIF + PS-rods (group 2). To assess spinal stability, the mean range of motion, lax zone, and stiff zone at L3-L4 were compared during flexion-extension, lateral bending, and axial rotation. With intact disc, stability was equivalent after PS-rod and CS-rod fixation, except that PS-rod fixation was stiffer during axial rotation. With DLIF support, there was no significant difference in stability between PS-rod and CS-rod fixation. With TLIF support, PS-rod fixation was stiffer than CS-rod fixation during lateral bending. Bilateral CS-rod fixation provided about the same stability in cadaveric specimens

Flexible scheme to truncate the hierarchy of pure states.

Science.gov (United States)

Zhang, P-P; Bentley, C D B; Eisfeld, A

2018-04-07

The hierarchy of pure states (HOPS) is a wavefunction-based method that can be used for numerically modeling open quantum systems. Formally, HOPS recovers the exact system dynamics for an infinite depth of the hierarchy. However, truncation of the hierarchy is required to numerically implement HOPS. We want to choose a "good" truncation method, where by "good" we mean that it is numerically feasible to check convergence of the results. For the truncation approximation used in previous applications of HOPS, convergence checks are numerically challenging. In this work, we demonstrate the application of the "n-particle approximation" to HOPS. We also introduce a new approximation, which we call the "n-mode approximation." We then explore the convergence of these truncation approximations with respect to the number of equations required in the hierarchy in two exemplary problems: absorption and energy transfer of molecular aggregates.

Flexible scheme to truncate the hierarchy of pure states

Science.gov (United States)

Zhang, P.-P.; Bentley, C. D. B.; Eisfeld, A.

2018-04-01

The hierarchy of pure states (HOPS) is a wavefunction-based method that can be used for numerically modeling open quantum systems. Formally, HOPS recovers the exact system dynamics for an infinite depth of the hierarchy. However, truncation of the hierarchy is required to numerically implement HOPS. We want to choose a "good" truncation method, where by "good" we mean that it is numerically feasible to check convergence of the results. For the truncation approximation used in previous applications of HOPS, convergence checks are numerically challenging. In this work, we demonstrate the application of the "n-particle approximation" to HOPS. We also introduce a new approximation, which we call the "n-mode approximation." We then explore the convergence of these truncation approximations with respect to the number of equations required in the hierarchy in two exemplary problems: absorption and energy transfer of molecular aggregates.

X-ray diffraction studies on merohedrally twinned Δ1-62NtNBCe1-A crystals of the sodium/bicarbonate cotransporter.

Science.gov (United States)

Gill, Harindarpal S; Dutcher, Lauren; Boron, Walter F; Patel, Samir; Guay-Woodford, Lisa M

2013-07-01

NBCe1-A membrane-embedded macromolecules that cotransport sodium and bicarbonate ions across the bilayer serve to maintain acid-base homeostasis throughout the body. Defects result in a number of renal and eye disorders, including type-II renal tubular acidosis and cataracts. Here, crystals of a human truncated mutant of the cytoplasmic N-terminal domain of NBCe1 (Δ1-62NtNBCe1-A) are reported that diffract X-rays to 2.4 Å resolution. The crystal symmetry of Δ1-62NtNBCe1-A is of space group P31 with pseudo-P3121 symmetry and it has a hemihedral twin fraction of 33.0%. The crystals may provide insight into the pathogenic processes observed in a subset of patients with truncating and point mutations in the gene encoding NBCe1.

Freely suspended rod fall dampener, especially for control rod of liquid-cooled nuclear reactor

International Nuclear Information System (INIS)

Becvar, J.; Saroch, V.

1977-01-01

A shock absorber is described whose advantage is that the space required for the movement of the shock absorber in the operating travel of the system suspension rod-control rod bundle may be reduced. The design allows the automatic disconnection of the system and the removal of the suspension rod from the reactor without dismantling. The braking force reaction is transmitted to the structure above the core. The system fall energy is absorbed on the side of the suspension rod which has a bigger mass. (J.B.)

RodPilot{sup R} - The Innovative and Cost-Effective Digital Control Rod Drive Control System for PWRs

Energy Technology Data Exchange (ETDEWEB)

Baron, Clemens [AREVA NP GmbH, NLEE-G, Postfach 1199, 91001 Erlangen (Germany)

2008-07-01

With RodPilot, AREVA NP offers an innovative and cost-effective system for controlling control rods in Pressurized Water Reactors. RodPilot controls the three operating coils of the control rod drive mechanism (lift, moveable gripper and stationary gripper coil). The rods are inserted into or withdrawn from the core as required by the Reactor Control System. The system combines modern components, state-of-the-art logic and a proven electronic control rod drive control principle to provide enhanced reliability and lower maintenance costs. (author)

Truncated predictor feedback for time-delay systems

CERN Document Server

Zhou, Bin

2014-01-01

This book provides a systematic approach to the design of predictor based controllers for (time-varying) linear systems with either (time-varying) input or state delays. Differently from those traditional predictor based controllers, which are infinite-dimensional static feedback laws and may cause difficulties in their practical implementation, this book develops a truncated predictor feedback (TPF) which involves only finite dimensional static state feedback. Features and topics: A novel approach referred to as truncated predictor feedback for the stabilization of (time-varying) time-delay systems in both the continuous-time setting and the discrete-time setting is built systematically Semi-global and global stabilization problems of linear time-delay systems subject to either magnitude saturation or energy constraints are solved in a systematic manner Both stabilization of a single system and consensus of a group of systems (multi-agent systems) are treated in a unified manner by applying the truncated pre...

Control-rod driving mechanism

International Nuclear Information System (INIS)

Jodoi, Takashi.

1976-01-01

Purpose: To prevent falling of control rods due to malfunction. Constitution: The device of the present invention has a scram function in particular, and uses principally a fluid pressure as a scram accelerating means. The control rod is held by upper and lower holding devices, which are connected by a connecting mechanism. This connecting mechanism is designed to be detachable only at the lower limit of driving stroke of the control rod so that there occurs no erroneous scram resulting from careless disconnection of the connecting mechanism. Further, scramming operation due to own weight of the scram operating portion such as control rod driving shaft may be effected to increase freedom. (Kamimura, M.)

REACTOR CONTROL ROD OPERATING SYSTEM

Science.gov (United States)

Miller, G.

1961-12-12

A nuclear reactor control rod mechanism is designed which mechanically moves the control rods into and out of the core under normal conditions but rapidly forces the control rods into the core by catapultic action in the event of an emergency. (AEC)

Frequency degeneracy of acoustic waves in two-dimensional phononic crystals

International Nuclear Information System (INIS)

Darinskii, A N; Le Clezio, E; Feuillard, G

2007-01-01

Degeneracies of acoustic wave spectra in 2D phononic crystals (PC) and PC slabs are studied. A PC structure is constituted of parallel steel rods immersed into water and forming the quadratic lattice. Given the projection k z of the wave vector on the direction of rods, the bulk wave spectrum of the infinite PC is a set of frequency surfaces f i (k x , k y ), i = 1,2,..., where k x,y are the components of the wave vector in the plane perpendicular to the rods. An investigation is performed of the shape of frequency surfaces in the vicinity of points (k dx , k dy ), where these surfaces fall into contact. In addition, the evolution of the degeneracy with changing rod radius and cross-section shape is examined. Degeneracy in the spectrum of leaky modes propagating along a single waveguide in a PC slab is also investigated

Crystallization of carbohydrate oxidase from Microdochium nivale

International Nuclear Information System (INIS)

Dušková, Jarmila; Dohnálek, Jan; Skálová, Tereza; Østergaard, Lars Henrik; Fuglsang, Claus Crone; Kolenko, Petr; Štěpánková, Andrea; Hašek, Jindřich

2009-01-01

Industrially used carbohydrate oxidase was successfully crystallized in several forms, diffraction data suitable for structural analysis were collected. Microdochium nivale carbohydrate oxidase was produced by heterologous recombinant expression in Aspergillus oryzae, purified and crystallized. The enzyme crystallizes with varying crystal morphologies depending on the crystallization conditions. Several different crystal forms were obtained using the hanging-drop vapour-diffusion method, two of which were used for diffraction measurements. Hexagon-shaped crystals (form I) diffracted to 2.66 Å resolution, with unit-cell parameters a = b = 55.7, c = 610.4 Å and apparent space group P6 2 22. Analysis of the data quality showed almost perfect twinning of the crystals. Attempts to solve the structure by molecular replacement did not give satisfactory results. Recently, clusters of rod-shaped crystals (form II) were grown in a solution containing PEG MME 550. These crystals belonged to the monoclinic system C2, with unit-cell parameters a = 132.9, b = 56.6, c = 86.5 Å, β = 95.7°. Data sets were collected to a resolution of 2.4 Å. The structure was solved by the molecular-replacement method. Model refinement is currently in progress

Purification, crystallization and preliminary X-ray diffraction of fluorescence recovery protein from Synechocystis PCC 6803

International Nuclear Information System (INIS)

Liu, Ting; Shuai, Yingli; Zhou, Honggang

2011-01-01

Fluorescence recovery protein from Synechocystis PCC 6803 plays a key role in the orange carotenoid protein-related photoprotective mechanism in cyanobacteria. The full-length form and a truncated form were overexpressed, purified and crystallized, and diffraction was observed to 2.75 Å resolution. Fluorescence recovery protein (FRP), which is encoded by the slr1964 gene in Synechocystis PCC 6803, plays a key role in the orange carotenoid protein-related photoprotective mechanism in cyanobacteria. As the crystal structure of FRP may provide information about the biological functions and mechanism of action of the protein, recombinant full-length FRP and a truncated form were overexpressed, purified and crystallized at 291 K using ethylene imine polymer as the precipitant. An FRP data set was collected to a resolution of 2.75 Å at low temperature (100 K). The crystal belonged to space group P4 1 2 1 2, with unit-cell parameters a = b = 61.9, c = 160.7 Å, α = β = γ = 90°. Assuming that the asymmetric unit contains three molecules, the Matthews coefficient was calculated to be 2.1 Å 3 Da −1

A molecular theory of smectic C liquid crystals made of rod-like molecules.

Science.gov (United States)

Govind, A S; Madhusudana, N V

2002-10-01

Organic compounds exhibiting the smectic C phase are made of rod-like molecules that have dipolar groups with lateral components. We argue that the off-axis character of the lateral dipolar groups can account for tilt in layered smectics (SmC, SmC*, SmI etc.). We develop a mean-field theory of the smectic C phase based on a single-particle potential of the form UC is proportional to sin(2theta) cos phi, consistent with the biaxial nature of the phase, where theta and phi are the polar and azimuthal angles, respectively. The hard-rod interactions that favour the smectic A phase with zero tilt angle are also included. The theoretical phase diagrams compare favourably with experimental trends. Our theory also leads to the following results: i) a first-order smectic C to smectic A transition above some value of the McMillan parameter alpha, leading to a tricritical point on the smectic C to smectic A transition line and ii) a first-order smectic C to smectic C transition over a very small range of values of the model parameters. We have also extended the theory to include the next higher-order term in the tilting potential and to include the effect of different tilt angles for the molecular core and the chain in the SmC phase.

Control rod velocity limiter

International Nuclear Information System (INIS)

Cearley, J.E.; Carruth, J.C.; Dixon, R.C.; Spencer, S.S.; Zuloaga, J.A. Jr.

1986-01-01

This patent describes a velocity control arrangement for a reciprocable, vertically oriented control rod for use in a nuclear reactor in a fluid medium, the control rod including a drive hub secured to and extending from one end therefrom. The control device comprises: a toroidally shaped control member spaced from and coaxially positioned around the hub and secured thereto by a plurality of spaced radial webs thereby providing an annular passage for fluid intermediate the hub and the toroidal member spaced therefrom in coaxial position. The side of the control member toward the control rod has a smooth generally conical surface. The side of the control member away from the control rod is formed with a concave surface constituting a single annular groove. The device also comprises inner and outer annular vanes radially spaced from one another and spaced from the side of the control member away from the control rod and positioned coaxially around and spaced from the hub and secured thereto by spaced radial webs thereby providing an annular passage for fluid intermediate the hub and the vanes. The vanes are angled toward the control member, the outer edge of the inner vane being closer to the control member and the inner edge of the outer vane being closer to the control member. When the control rod moves in the fluid in the direction toward the drive hub the vanes direct a flow of fluid turbulence which provides greater resistance to movement of the control rod in the direction toward the drive hub than in the other direction

Control rod position control device

International Nuclear Information System (INIS)

Ubukata, Shinji.

1997-01-01

The present invention provides a control rod position control device which stores data such as of position signals and driving control rod instruction before and after occurrence of abnormality in control for the control rod position for controlling reactor power and utilized the data effectively for investigating the cause of abnormality. Namely, a plurality of individual control devices have an operation mismatching detection circuit for outputting signals when difference is caused between a driving instruction given to the control rod position control device and the control rod driving means and signals from a detection means for detecting an actual moving amount. A general control device collectively controls the individual control devices. In addition, there is also disposed a position storing circuit for storing position signals at least before and after the occurrence of the control rod operation mismatching. With such procedures, the cause of the abnormality can be determined based on the position signals before and after the occurrence of control rod mismatching operation stored in the position storing circuit. Accordingly, the abnormality cause can be determined to conduct restoration in an early stage. (I.S.)

Control rod selecting and driving device

International Nuclear Information System (INIS)

Isobe, Hideo.

1981-01-01

Purpose: To simultaneously drive a predetermined number of control rods in a predetermined mode by the control of addresses for predetermined number of control rods and read or write of driving codified data to and from the memory by way of a memory controller. Constitution: The system comprises a control rod information selection device for selecting predetermined control rods from a plurality of control rods disposed in a reactor and outputting information for driving them in a predetermined mode, a control rod information output device for codifying the information outputted from the above device and outputting the addresses to the predetermined control rods and driving mode coded data, and a driving device for driving said predetermined control rods in a predetermined mode in accordance with the codified data outputted from the above device, said control rod infromation output device comprising a memory device capable of storing a predetermined number of the codified data and a memory control device for storing the predetermined number of data into the above memory device at a predetermined timing while successively outputting the thus stored predetermined number of data at a predetermined timing. (Seki, T.)

NEUTRONIC REACTOR CONTROL ROD DRIVE APPARATUS

Science.gov (United States)

Oakes, L.C.; Walker, C.S.

1959-12-15

ABS>A suspension mechanism between a vertically movable nuclear reactor control rod and a rod extension, which also provides information for the operator or an automatic control signal, is described. A spring connects the rod extension to a drive shift. The extension of the spring indicates whether (1) the rod is at rest on the reactor, (2) the rod and extension are suspended, or (3) the extension alone is suspended, the spring controlling a 3-position electrical switch.

RODDRP - A FORTRAN program for use in control rod calibration by the rod drop method

International Nuclear Information System (INIS)

Wilson, W.E.

1972-01-01

The different methods to measure reactivity which are applicable to control rod calibration are discussed. They include: 1) the positive period method, 2) the rod drop method, 3) the source-jerk method, 4) the rod oscillation method, and 5) the pulsed neutron method. The instrument setup used at WSU for rod drop measurements is presented. To speed up the analysis of power fall-off trace, a FORTRAN IV program called RODDRP was written to simultaneously solve the in-hour equation and relative neutron flux. The procedure for calculating the worth of the rod that produced the power trace is given. The reactivity for each time relative flux point is obtained. Conclusions about the status of the equipment are made

New results to BDD truncation method for efficient top event probability calculation

International Nuclear Information System (INIS)

Mo, Yuchang; Zhong, Farong; Zhao, Xiangfu; Yang, Quansheng; Cui, Gang

2012-01-01

A Binary Decision Diagram (BDD) is a graph-based data structure that calculates an exact top event probability (TEP). It has been a very difficult task to develop an efficient BDD algorithm that can solve a large problem since its memory consumption is very high. Recently, in order to solve a large reliability problem within limited computational resources, Jung presented an efficient method to maintain a small BDD size by a BDD truncation during a BDD calculation. In this paper, it is first identified that Jung's BDD truncation algorithm can be improved for a more practical use. Then, a more efficient truncation algorithm is proposed in this paper, which can generate truncated BDD with smaller size and approximate TEP with smaller truncation error. Empirical results showed this new algorithm uses slightly less running time and slightly more storage usage than Jung's algorithm. It was also found, that designing a truncation algorithm with ideal features for every possible fault tree is very difficult, if not impossible. The so-called ideal features of this paper would be that with the decrease of truncation limits, the size of truncated BDD converges to the size of exact BDD, but should never be larger than exact BDD.

Maximum nondiffracting propagation distance of aperture-truncated Airy beams

Science.gov (United States)

Chu, Xingchun; Zhao, Shanghong; Fang, Yingwu

2018-05-01

Airy beams have called attention of many researchers due to their non-diffracting, self-healing and transverse accelerating properties. A key issue in research of Airy beams and its applications is how to evaluate their nondiffracting propagation distance. In this paper, the critical transverse extent of physically realizable Airy beams is analyzed under the local spatial frequency methodology. The maximum nondiffracting propagation distance of aperture-truncated Airy beams is formulated and analyzed based on their local spatial frequency. The validity of the formula is verified by comparing the maximum nondiffracting propagation distance of an aperture-truncated ideal Airy beam, aperture-truncated exponentially decaying Airy beam and exponentially decaying Airy beam. Results show that the formula can be used to evaluate accurately the maximum nondiffracting propagation distance of an aperture-truncated ideal Airy beam. Therefore, it can guide us to select appropriate parameters to generate Airy beams with long nondiffracting propagation distance that have potential application in the fields of laser weapons or optical communications.

Simulation of vibration modes of the fuel rod damaged due to the grid-to-rod fretting wear

International Nuclear Information System (INIS)

Kim, Kyu Tae; Kim, Kyeong Koo; Jang, Young Ki; Lee, Kyou Seok

1997-01-01

The flow-induced fuel fretting wear observed in some PWRs mainly proceeds in the grid-to-rod contact positions. The grid-to-rod fretting wear in the PWR fuel assembly depends on grid-to-rod gap size, its axial profile and flow-induced vibration. This paper describes the GRIDFORCE program which generates the axially dependent grid-to-rod gap size as a function of burnup. The axially dependent grid-to-rod gap profiles are employed to predict the fuel rod vibration mode shapes by the ANSYS code. With the help of the Paidousis empirical formula, this paper also calculates the fuel rod vibration amplitudes under various supporting conditions, which indicates that the increase of the number of unsupported mid-grids will increase the fuel rod vibration amplitude. On the other hand, the comparison of the predicted vibration mode shapes and the observed mid-grid fretting wear pattern indicates that the 1st and 6th vibration mode shapes under the supporting inactive condition at the mid-grids can simulate the observed mid-grid fretting wear profile. This paper also proposes design guidelines against the grid-to-rod fretting wear. (author). 3 refs., 8 figs

Automated nuclear fuel rod pattern loading system

International Nuclear Information System (INIS)

Lambert, D.V.; Nylund, T.W.; Byers, J.W.; Haley, D.E. Jr.; Cioffi, J.V.

1991-01-01

This patent describes a method for loading fuel rods in a desired pattern. It comprises providing a supply of fuel rods of known enrichments; providing a magazine defining a matrix of elongated slots open at their forward ends for receiving fuel rods; defining a fuel rod feed path; receiving successively one at a time along the feed path fuel rods selected from the supply thereof; verifying successively one at a time along the feed path the identity of the selected fuel rods, the verifying including blocking passage of each selected fuel rod along the feed path until the identity of each selected fuel rod is confirmed as correct; feeding to the magazine successively one at a time along the feed path the selective and verified fuel rods; and supporting and moving the magazine along X-Y axes to successively align one at a time selected ones of the slots with the feed path for loading in the magazine the successive fuel rods in a desired enrichment pattern

An iterative reconstruction from truncated projection data

International Nuclear Information System (INIS)

Anon.

1985-01-01

Various methods have been proposed for tomographic reconstruction from truncated projection data. In this paper, a reconstructive method is discussed which consists of iterations of filtered back-projection, reprojection and some nonlinear processings. First, the method is so constructed that it converges to a fixed point. Then, to examine its effectiveness, comparisons are made by computer experiments with two existing reconstructive methods for truncated projection data, that is, the method of extrapolation based on the smooth assumption followed by filtered back-projection, and modified additive ART

Layering and Ordering in Electrochemical Double Layers

Energy Technology Data Exchange (ETDEWEB)

Liu, Yihua [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States; Kawaguchi, Tomoya [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States; Pierce, Michael S. [Rochester Institute of Technology, School of Physics and Astronomy, Rochester, New York 14623, United States; Komanicky, Vladimir [Faculty of Science, Safarik University, 041 54 Kosice, Slovakia; You, Hoydoo [Materials Science Division, Argonne National Laboratory, Argonne, Illinois 60439, United States

2018-02-26

Electrochemical double layers (EDL) form at electrified interfaces. While Gouy-Chapman model describes moderately charged EDL, formation of Stern layers was predicted for highly charged EDL. Our results provide structural evidence for a Stern layer of cations, at potentials close to hydrogen evolution in alkali fluoride and chloride electrolytes. Layering was observed by x-ray crystal truncation rods and atomic-scale recoil responses of Pt(111) surface layers. Ordering in the layer is confirmed by glancing-incidence in-plane diffraction measurements.

Control rod drives

International Nuclear Information System (INIS)

Ikakura, Hiroaki.

1986-01-01

Purpose: To enable to direct disconnection of control rods upon abnormal temperature rise in the reactor thereby improve the reliability for the disconnecting operation in control rod drives for FBR type reactors upon emergency. Constitution: A diaphragm is disposed to the upper opening of a sealing vessel inserted to the hollow portion of an electromagnet and a rod is secured to the central position of the upper surface. A spring contacts are attached by way of an insulator to the inner surface at the lower portion of an extension pipe and connected with cables for supplying electric power sources respectively to a magnet. If the temperature in the reactor abnormally rises, liquid metals in the sealing vessel are expanded tending to extend the bellows downwardly. However, since they are attracted by the electromagnet, the thermal expansion of the liquid metals exert on the diaphragm prior to the bellows. Thus, the switch between the spring contacts is made open to attain the deenergized state to thereby disconnect the control rod and shutdown the neclear reactor. (Horiuchi, T.)

Acoustic band gaps of the woodpile sonic crystal with the simple cubic lattice

Energy Technology Data Exchange (ETDEWEB)

Wu, Liang-Yu; Chen, Lien-Wen, E-mail: chenlw@mail.ncku.edu.t [Department of Mechanical Engineering, National Cheng Kung University, Tainan 70101, Taiwan (China)

2011-02-02

This study theoretically and experimentally investigates the acoustic band gap of a three-dimensional woodpile sonic crystal. Such crystals are built by blocks or rods that are orthogonally stacked together. The adjacent layers are perpendicular to each other. The woodpile structure is embedded in air background. Their band structures and transmission spectra are calculated using the finite element method with a periodic boundary condition. The dependence of the band gap on the width of the stacked rods is discussed. The deaf bands in the band structure are observed by comparing with the calculated transmission spectra. The experimental transmission spectra for the {Gamma}-X and {Gamma}-X' directions are also presented. The calculated results are compared with the experimental results.

Method for compacting spent nuclear reactor fuel rods

International Nuclear Information System (INIS)

Wachter, W.J.

1988-01-01

In a nuclear reactor system which requires periodic physical manipulation of spent fuel rods, the method of compacting fuel rods from a fuel rod assembly is described. The method consists of: (1) removing the top end from the fuel rod assembly; (2) passing each of multiple fuel rod pulling elements in sequence through a fuel rod container and thence through respective consolidating passages in a fuel rod directing chamber; (3) engaging one of the pulling elements to the top end of each of the fuel rods; (4) drawing each of the pulling elements axially to draw the respective engaged fuel rods in one axial direction through the respective the passages in the chamber to thereby consolidate the fuel rods into a compacted configuration of a cross-sectional area smaller than the cross-sectional area occupied thereby within the fuel rod assembly; and (5) drawing all of the engaged fuel rods concurrently and substantially parallel to one another in the one axial direction into the fuel rod container while maintaining the compacted configuration whereby the fuel rods are aligned within the container in a fuel rod density of the the fuel rod assembly

Control rod drives

International Nuclear Information System (INIS)

Asano, Hiromitsu.

1979-01-01

Purpose: To drive control rods at an optimum safety speed corresponding to the reactor core output. Constitution: The reactor power is detected by a neutron detector and the output signal is applied to a process computer. The process computer issues a signal representing the reactor core output, which is converted through a function generator into a signal representing the safety speed of control rods. The converted signal is further supplied to a V/F converter and converted into a pulse signal. The pulse signal is inputted to a step motor driving circuit, which actuates a step motor to operate the control rods always at a safety speed corresponding to the reactor core power. (Furukawa, Y.)

Individual nuclear fuel rod weighing system

International Nuclear Information System (INIS)

Fogg, J. L.; Howell, C. A.; Smith, J. H.; Vining, G. E.

1985-01-01

An individual nuclear fuel rod weighing system for rods carried on a tray which moves along a materials handling conveyor. At a first tray position on the conveyor, a lifting device raises the rods off the tray and places them on an overhead ramp. A loading mechanism conveys the rods singly from the overhead ramp onto an overhead scale for individual weighing. When the tray is at a second position on the conveyor, a transfer apparatus transports each weighed rod from the scale back onto the tray

Measuring device for control rod driving time

International Nuclear Information System (INIS)

Tanaka, Kazuhiko; Hanabusa, Masatoshi.

1993-01-01

The present invention concerns a measuring device for control driving time having a function capable of measuring a selected control rod driving time and measuring an entire control rod driving time simultaneously. A calculation means and a store means for the selected rod control rod driving time, and a calculation means and a store means for the entire control rod driving time are disposed individually. Each of them measures the driving time and stores the data independent of each other based on a selected control rod insert ion signal and an entire control rod insertion signal. Even if insertion of selected and entire control rods overlaps, each of the control rod driving times can be measured reliably to provide an advantageous effect capable of more accurately conducting safety evaluation for the nuclear reactor based on the result of the measurement. (N.H.)

Growth and Morphology of Rod Eutectics

Energy Technology Data Exchange (ETDEWEB)

Jing Teng; Shan Liu; R. Trivedi

2008-03-17

The formation of rod eutectic microstructure is investigated systematically in a succinonitrile-camphor alloy of eutectic composition by using the directional solidification technique. A new rod eutectic configuration is observed in which the rods form with elliptical cylindrical shape. Two different orientations of the ellipse are observed that differ by a 90{sup o} rotation such that the major and the minor axes are interchanged. Critical experiments in thin samples, where a single layer of rods forms, show that the spacing and orientation of the elliptic rods are governed by the growth rate and the sample thickness. In thicker samples, multi layers of rods form with circular cross-section and the scaling law between the spacing and velocity predicted by the Jackson and Hunt model is validated. A theoretical model is developed for a two-dimensional array of elliptical rods that are arranged in a hexagonal or a square array, and the results are shown to be consistent with the experimental observations. The model of elliptic rods is also shown to reduce to that for the circular rod eutectic when the lengths of the two axes are equal, and to the lamellar eutectic model when one of the axes is much larger than the other one.

Status of rod consolidation, 1988

International Nuclear Information System (INIS)

Bailey, W.J.

1989-01-01

It is estimated that the spent fuel storage pools at some domestic light-water reactors will run out of space before 2003, the year that the US Department of Energy currently predicts it will have a repository available. Of the methods being studied to alleviate the problem, rod consolidation is one of the leading candidates for achieving more efficient use of existing space in spent fuel storage pools. Rod consolidation involves mechanically removing all the fuel rods from the fuel assembly hardware (i.e., the structural components) and placing the fuel rods in a close-packed array in a canister without space grids. A typical goal of rod consolidation systems is to insert the fuel rods from two fuel assemblies into a canister that has the same exterior dimensions as one standard fuel assembly (i.e., to achieve a consolidation or compaction ratio of 2:1) and to compact the nonfuel-bearing structural components from those two fuel assemblies by a factor of 10 to 20. This report provides an overview of the current status of rod consolidation in the United States and a small amount of information on related activities in other countries. 85 refs., 36 figs., 5 tabs

Inspecting method for fuel rods

International Nuclear Information System (INIS)

Watanabe, Masaaki; Kogure, Sumio.

1976-01-01

Purpose: To precisely detect the response of flaw in clad tube and submerged fuel pellets from a relationship between the surface of fuel rod and internal signal. Constitution: Ultrasonic reflected waves from the surface of fuel rods and the interior are detected and either one of fuel rod or ultrasonic flaw detecting contact is rotated to thereby precisely detect the response of the flaw of clad tube and submerged fuel pellets from a relationship between said surface and the interior. It will be noted that the ultrasonic flaw detecting contact used is of the line-focus type, the incident angle of ultrasonic wave from the ultrasonic flaw detecting contact relative to the fuel rod is the angle of skew, that is, the ultrasonic flaw detecting contact is not perpendicular to a center axis of the fuel rod but is slightly displace. That is, the use of the aforesaid contact may facilitate discrimination between the surface flaw of the fuel rod and the response of submergence, and in addition, the employment of the aforesaid incident angle makes it hard to receive reflected waves from the surface of the fuel rod which is great in terms of energy to facilitate discrimination of waves responsive to submergence. (Kawakami, Y.)

Control rod position detection device

International Nuclear Information System (INIS)

Akita, Haruo; Ogiwara, Sakae.

1996-01-01

The device of the present invention is used in a back-up shut down system of an LMFBR type reactor which is easy for maintenance, has high reliability and can recognize the position of control rods accurately. Namely, a permanent magnet is disposed to a control rod extension tube connected to the lower portion of the control rod. The detector guide tube is disposed in the vicinity of the control rod extension tube. A detector having a detection coil is inserted into a detector tube. With such constitution, the control rod can be detected at one position using the following method. (1) the movement of the magnetic field of the permanent magnet is detected by the detection coil. (2) a plurality of grooves are formed on the control rod extension tube, and the movement of the grooves is detected. In addition, the detection coil is inserted into the detector guide tube, and the signals from the detection coil are inputted to a signal processing circuit disposed at the outside of the reactor vessel using an MI cable to enable the maintenance of the detector. Further, if the detector comprises a detection coil and an excitation coil, the position of a dropped control rod can be recognized at a plurality of points. (I.S.)

Rope wind-up type control rod

International Nuclear Information System (INIS)

Tsuji, Teruaki; Watanabe, Shigeru.

1979-01-01

Purpose: To hold a control rod at a certain position even if the sealed cover of the rod drive mechanism should fail. Constitution: A plurality of friction plates, engaging wheels and a threaded shaft are provided to the wind-up drum for winding up a rope which moves the control rod up and down. While the control rod is adapted to drop by its own weight upon insertion, it is adapted to stop at a predetermined position exactly with no shocks by gradually increasing braking force by the sliding friction caused from the friction plates or the like. A ratch mechanism is provided to the upper portion of the control rod so that the top of the ratch piece may automatically engage the guide passage wall of the control rod upon uncontrolled running of the control rod to prevent further uncontrolled running thereof. (Ikeda, J.)

ELECTROMAGNETIC APPARATUS FOR MOVING A ROD

Science.gov (United States)

Young, J.N.

1958-04-22

An electromagnetic apparatus for moving a rod-like member in small steps in either direction is described. The invention has particular application in the reactor field where the reactor control rods must be moved only a small distance and where the use of mechanical couplings is impractical due to the high- pressure seals required. A neutron-absorbing rod is mounted in a housing with gripping uaits that engage the rod, and coils for magnetizing the gripping units to make them grip, shift, and release the rod are located outside the housing.

Individual nuclear fuel rod weighing system

International Nuclear Information System (INIS)

Fogg, J.L.; Smith, J.H.; Vining, G.E.; Howell, C.A.

1985-01-01

An individual nuclear fuel rod weighing system for rods carried on a tray which moves along a materials handling conveyor is discussed. At a first tray position on the conveyor, a lifting device raises the rods off the tray and places them on an overhead ramp. A loading mechanism conveys the rods singly from the overhead ramp onto an overhead scale for individual weighing. When the tray is at a second position on the conveyor, a transfer apparatus transports each weighed rod from the scale back onto the tray

Frequency degeneracy of acoustic waves in two-dimensional phononic crystals

Energy Technology Data Exchange (ETDEWEB)

Darinskii, A N [Institute of Crystallography RAS, Leninskiy pr. 59, Moscow, 119333 (Russian Federation); Le Clezio, E [Universite Francois Rabelais de Tours, ENI Val de Loire, LUSSI, FRE CNRS 2448, rue de la Chocolaterie, BP3410, 41034 Blois (France); Feuillard, G [Universite Francois Rabelais de Tours, ENI Val de Loire, LUSSI, FRE CNRS 2448, rue de la Chocolaterie, BP3410, 41034 Blois (France)

2007-12-15

Degeneracies of acoustic wave spectra in 2D phononic crystals (PC) and PC slabs are studied. A PC structure is constituted of parallel steel rods immersed into water and forming the quadratic lattice. Given the projection k{sub z} of the wave vector on the direction of rods, the bulk wave spectrum of the infinite PC is a set of frequency surfaces f{sub i}(k{sub x}, k{sub y}), i = 1,2,..., where k{sub x,y} are the components of the wave vector in the plane perpendicular to the rods. An investigation is performed of the shape of frequency surfaces in the vicinity of points (k{sub dx}, k{sub dy}), where these surfaces fall into contact. In addition, the evolution of the degeneracy with changing rod radius and cross-section shape is examined. Degeneracy in the spectrum of leaky modes propagating along a single waveguide in a PC slab is also investigated.

Control rods in LMFBRs: a physics assessment

International Nuclear Information System (INIS)

McFarlane, H.F.; Collins, P.J.

1982-08-01

This physics assessment is based on roughly 300 control rod worth measurements in ZPPR from 1972 to 1981. All ZPPR assemblies simulated mixed-oxide LMFBRs, representing sizes of 350, 700, and 900 MWe. Control rod worth measurements included single rods, various combinations of rods, and Ta and Eu rods. Additional measurements studied variations in B 4 C enrichment, rod interaction effects, variations in rod geometry, neutron streaming in sodium-filled channels, and axial worth profiles. Analyses were done with design-equivalent methods, using ENDF/B Version IV data. Some computations for the sensitivities to approximations in the methods have been included. Comparisons of these analyses with the experiments have allowed the status of control rod physics in the US to be clearly defined

Measurements of Burnout Conditions for Flow of Boiling Water in Vertical 3-Rod and 7-Rod Clusters

Energy Technology Data Exchange (ETDEWEB)

Becker, Kurt M; Hernborg, G; Flinta, J E

1964-08-15

The present report deals with measurements of burnout conditions for flow of boiling water in vertical 3-rod and 7-rod clusters. Data were obtained,in respect of heating the rods only, as well as for simultaneous uniform and non-uniform heating of the rods and the shroud. Totally, 520 runs were performed. In the case of equal heat fluxes on all surfaces of the channels, burnout always occurred on the rods, and the data were low by a factor of about 1.3 compared with round duct data. When only the rods were heated, the data showed very low burnout values in comparison with the results for total uniform heating and round ducts. This disagreement was explained by considering the climbing film flow model and the fact that only a fraction of the channel perimeter was heated. For simultaneous and non-uniform heating of the rods and the shroud it was found that the shroud could be overloaded up to 50 per cent without reducing the margin of safety in respect of burnout for the rod cluster. Finally, a correlation for predicting burnout conditions in round ducts, annuli and rod clusters has been presented. This correlation predicts the burnout heat fluxes for the present measurements and previously obtained annuli measurements within {+-} 5 per cent.

Characterization of Baculovirus Insecticides Expressing Tailored Bacillus thuringiensis CryIA(b) Crystal Proteins

NARCIS (Netherlands)

Martens, John W M; Knoester, Marga; Weijts, Franci; Groffen, Sander J A; Hu, Zhihong; Bosch, Dirk; Vlak, Just M.

1995-01-01

Full-length, truncated, and mature forms of the CryIA(b) insecticidal crystal protein gene of Bacillus thuringiensis were engineered into the p10 locus of Autographa californica nuclear polyhedrosis virus (AcNPV). A signal sequence of Heliothis virescens juvenile hormone esterase was introduced at

Development of a control rod drive

International Nuclear Information System (INIS)

1991-01-01

In the period under review, the computer codes required for transients calculation have been completed, as well as the programs for modelling and testing the hot-gas temperature control by means of combined core rod and reflector rod operation. The specification of requirements to be fulfilled by the rod drive computer and the neutron flux measuring system has been done relying essentially on the data obtained by the transients calculations performed and the resulting informations on operating conditions. The work for optimization of the core rod drive with regard to rod driving speeds and the 'three-point switch' with hysteresis for controlled, automatic core rod operation has been concentrating on the case of specified, normal operation of the reactor. (orig./DG) [de

Self-Assembly of Rod-Coil Block Copolymers

National Research Council Canada - National Science Library

Jenekhe, S

1999-01-01

... the self-assembly of new rod-coil diblock, rod- coil-rod triblock, and coil-rod-coil triblock copolymers from solution and the resulting discrete and periodic mesostmctares with sizes in the 100...

Truncated Wigner dynamics and conservation laws

Science.gov (United States)

Drummond, Peter D.; Opanchuk, Bogdan

2017-10-01

Ultracold Bose gases can be used to experimentally test many-body theory predictions. Here we point out that both exact conservation laws and dynamical invariants exist in the topical case of the one-dimensional Bose gas, and these provide an important validation of methods. We show that the first four quantum conservation laws are exactly conserved in the approximate truncated Wigner approach to many-body quantum dynamics. Center-of-mass position variance is also exactly calculable. This is nearly exact in the truncated Wigner approximation, apart from small terms that vanish as N-3 /2 as N →∞ with fixed momentum cutoff. Examples of this are calculated in experimentally relevant, mesoscopic cases.

Liquid crystal dimers

CERN Document Server

Kumar Pal, Santanu

2017-01-01

This book covers in-depth discussion of design principles, synthesis and thermal behavior of all types of liquid crystal (LC) dimers. The text presents recent advances in the field of LC dimers consisting of different mesogenic units such as calamitic, discotic and bent-core molecules. It starts with a chapter on the introduction of liquid crystal dimers, including their odd-even behavior, basic classification of dimers and common mesophases in dimers. The text shows how the molecular architectures are being used to develop new materials to study a range of interesting phenomena such as the biaxial nematic phase containing rod-like and disc-like mesogenic units. Finally, the text presents perspectives related to technological relevance of these dimers such as dopants in LC display mixtures exhibiting faster relaxation time, strong flexoelectric coupling and others to effect control over the properties of these materials.

Ejected control rod and rods drop measurements during Mochovce startup physical tests

International Nuclear Information System (INIS)

Minarcin, Miroslav; Elko, Marek

1998-01-01

Paper deals with measurements of asymmetric reactivity insertion into the reactor core that were carried out during physical startup tests of Mochovce Unit 1 in June 1998. Control rods worth measurements with one and two rods s tucked in upper limit and worth measurement of one control rod from group 6 'ejected' from the reactor core are discussed. During the experiments neutron flux was measured by four ionisation chambers (three of them were placed symmetrically around the reactor core). Results of measurements and influence of asymmetric reactivity influence on ionisation chambers response are presented in the paper. (Authors)

Quivers For Special Fuel Rods-Disposal Of Special Fuel Rods In CASTOR V Casks

International Nuclear Information System (INIS)

Bannani, Amin; Cebula, Wojciech; Buchmuller, Olga; Huggenberg, Roland; Helmut Kuhl

2015-01-01

While GNS casks of the CASTOR family are a suitable means to transfer fuel assemblies (FA) from the NPP to an interim dry storage site, Germanys phase-out of nuclear energy has triggered the demand for an additional solution to dispose of special fuel rods (SFR), normally remaining in the fuel pond until the final shutdown of the NPP. SFR are fuel rods that had to be removed from fuel assemblies mainly due to their special condition, e. g. damages in the cladding of the fuel rods which may have occurred during reactor operations. SFR are usually stored in the spent fuel pond after they are removed from the FA. The quiver for special fuel rods features a robust yet simple design, with a high mechanical stability, a reliable leak-tightness and large safety margins for future requirements on safety analysis. The quiver for special fuel rods can be easily adapted to a large variety of different damaged fuel rods and tailored to the specific need of the customer. The quiver for special fuel rods is adaptable e.g. in length and diameter for use in other types of transport and storage casks and is applicable in other countries as well. The overall concept presented here is a first of its kind solution for the disposal of SFRs via Castor V-casks. This provides an important precondition in achieving the status 'free from nuclear fuel' of the shut down German NPPs

Quivers For Special Fuel Rods-Disposal Of Special Fuel Rods In CASTOR V Casks

Energy Technology Data Exchange (ETDEWEB)

Bannani, Amin; Cebula, Wojciech; Buchmuller, Olga; Huggenberg, Roland [GNS, Essen (Germany); Helmut Kuhl [WTI, Julich (Germany)

2015-05-15

While GNS casks of the CASTOR family are a suitable means to transfer fuel assemblies (FA) from the NPP to an interim dry storage site, Germanys phase-out of nuclear energy has triggered the demand for an additional solution to dispose of special fuel rods (SFR), normally remaining in the fuel pond until the final shutdown of the NPP. SFR are fuel rods that had to be removed from fuel assemblies mainly due to their special condition, e. g. damages in the cladding of the fuel rods which may have occurred during reactor operations. SFR are usually stored in the spent fuel pond after they are removed from the FA. The quiver for special fuel rods features a robust yet simple design, with a high mechanical stability, a reliable leak-tightness and large safety margins for future requirements on safety analysis. The quiver for special fuel rods can be easily adapted to a large variety of different damaged fuel rods and tailored to the specific need of the customer. The quiver for special fuel rods is adaptable e.g. in length and diameter for use in other types of transport and storage casks and is applicable in other countries as well. The overall concept presented here is a first of its kind solution for the disposal of SFRs via Castor V-casks. This provides an important precondition in achieving the status 'free from nuclear fuel' of the shut down German NPPs.

Monitoring device for withdrawing control rods

International Nuclear Information System (INIS)

Higashigawa, Yuichi.

1985-01-01

Purpose: To improve the sensitivity and the responsivity to an equivalent extent to those in the case where local power range monitors are densely arranged near each of the control rods, with no actual but pseudo increase of the number of local power range monitors. Constitution: The monitor arrangement is patterned by utilizing the symmetricity of the reactor core and stored in a monitor designating device. The symmetricity of control rods to be selected and withdrawn by an operator is judged by a control rod symmetry monitoring device, while the symmetricity of the withdrawn control rods is judged by a control rod withdrawal state monitoring device. Then, only when both of the devices judge the symmetricity, the control rods are subjected to gang driving by the control rod drive mechanisms. In this way, monitoring at a high sensitivity and responsivity is enabled with no increase for the number of monitors. (Yoshino, Y.)

Nondestructive assay of HTGR fuel rods

International Nuclear Information System (INIS)

Menlove, H.O.

1974-01-01

Performance characteristics of three different radioactive source NDA systems are compared for the assay of HTGR fuel rods and stacks of rods. These systems include the fast neutron Sb-Be assay system, the 252 Cf ''Shuffler,'' and the thermal neutron PAPAS assay system. Studies have been made to determinethe perturbation on the measurements from particle size, kernel Th/U ratio, thorium content, and hydrogen content. In addition to the total 235 U determination, the pellet-to-pellet or rod-to-rod uniformity of HTGR fuel rod stacks has been measured by counting the delayed gamma rays with a NaI through-hole in the PAPAS system. These measurements showed that rod substitutions can be detected easily in a fuel stack, and that detailed information is available on the loading variations in a uniform stack. Using a 1.0 mg 252 Cf source, assay rates of 2 to 4 rods/s are possible, thus facilitating measurement of 100 percent of a plant's throughput. (U.S.)

Inspection system for Zircaloy clad fuel rods

International Nuclear Information System (INIS)

Yancey, M.E.; Porter, E.H.; Hansen, H.R.

1975-10-01

A description is presented of the design, development, and performance of a remote scanning system for nondestructive examination of fuel rods. Characteristics that are examined include microcracking of fuel rod cladding, fuel-cladding interaction, cladding thickness, fuel rod diameter variation, and fuel rod bowing. Microcracking of both the inner and outer fuel rod surfaces and variations in wall thickness are detected by using a pulsed eddy current technique developed by Argonne National Laboratory (ANL). Fuel rod diameter variation and fuel rod bowing are detected by using two linear variable differential transformers (LVDTs) and a signal conditioning system. The system's mechanical features include variable scanning speeds, a precision indexing system, and a servomechanism to maintain proper probe alignment. Initial results indicate that the system is a very useful mechanism for characterizing irradiated fuel rods

Seismic scrammability of HTTR control rods

International Nuclear Information System (INIS)

Nishiguchi, I.; Iyoku, T.; Ito, N.; Watanabe, Y.; Araki, T.; Katagiri, S.

1990-01-01

Scrammability tests on HTTR (High-Temperature Engineering Test Reactor) control rods under seismic conditions have been carried out and seismic conditions influences on scram time as well as functional integrity were examined. A control rod drive located in a stand-pipe at the top of a reactor vessel, raises and lowers a pair of control rods by suspension cables. Each flexible control rod consists of 10 neutron absorber sections held together by a metal spine passing through the center. It falls into a hole in graphite blocks due to gravity at scram. In the tests, a full scale control rod drive and a pair of control rods were employed with a column of graphite blocks in which holes for rods were formed. Blocks misalignment and contact with the hole surface during earthquakes were considered as major causes of disturbance in scram time. Therefore, the following parameters were set up in the tests: excitation direction, combination or horizontal and vertical excitation, acceleration, frequency and block to block gaps. Main results obtained from tests are as follow. 1) Every scram time obtained under the design conditions was within 6 seconds. On the contrary, the scram times were 5.2 seconds when there were no vibration. Therefore, it was concluded that the seismic effects on scram time were not significant. 2) Scram time became longer with increase in both acceleration and horizontal excitation frequency, and control rods fell very smoothly without any jerkiness. This suggests that collision between control rods and hole surface is the main disturbing factor of falling motion. 3) Mechanical and functional integrity of control rod drive mechanism, control rods and graphite blocks was confirmed after 140 seismic scrammability tests. (author). 10 figs, 1 tab

Control rod testing apparatus

International Nuclear Information System (INIS)

Gaunt, R.R.; Ashman, C.M.

1987-01-01

A control rod testing apparatus is described comprising: a first guide means having a vertical cylindrical opening for grossly guiding a control rod; a second guide means having a vertical cylindrical opening for grossly guiding a control rod. The first and second guide means are supported at axially spaced locations with the openings coaxial; and a substantially cylindrical subassembly having a vertical cylindrical opening therethrough. The subassembly is trapped coaxial with and between the first and second guide means, and the subassembly radially floats with respect to the first and second guide means

Development of the automatic control rod operation system for JOYO. Verification of automatic control rod operation guide system

International Nuclear Information System (INIS)

Terakado, Tsuguo; Suzuki, Shinya; Kawai, Masashi; Aoki, Hiroshi; Ohkubo, Toshiyuki

1999-10-01

The automatic control rod operation system was developed to control the JOYO reactor power automatically in all operation modes(critical approach, cooling system heat up, power ascent, power descent), development began in 1989. Prior to applying the system, verification tests of the automatic control rod operation guide system was conducted during 32nd duty cycles of JOYO' from Dec. 1997 to Feb. 1998. The automatic control rod operation guide system consists of the control rod operation guide function and the plant operation guide function. The control rod operation guide function provides information on control rod movement and position, while the plant operation guide function provide guidance for plant operations corresponding to reactor power changes(power ascent or power descent). Control rod insertion or withdrawing are predicted by fuzzy algorithms. (J.P.N.)

Control rod drive shaft latch

International Nuclear Information System (INIS)

Thorp, A.G. II.

1976-01-01

A latch mechanism is operated by differential pressure on a piston to engage the drive shaft for a control rod in a nuclear reactor, thereby preventing the control rod from being ejected from the reactor in case of failure of the control rod drive mechanism housing which is subjected to the internal pressure in the reactor vessel. 6 claims, 4 drawing figures

Measurements of Burnout Conditions for Flow of Boiling Water in Vertical 3-Rod and 7-Rod Clusters

International Nuclear Information System (INIS)

Becker, Kurt M.; Hernborg, G.; Flinta, J.E.

1964-08-01

The present report deals with measurements of burnout conditions for flow of boiling water in vertical 3-rod and 7-rod clusters. Data were obtained,in respect of heating the rods only, as well as for simultaneous uniform and non-uniform heating of the rods and the shroud. Totally, 520 runs were performed. In the case of equal heat fluxes on all surfaces of the channels, burnout always occurred on the rods, and the data were low by a factor of about 1.3 compared with round duct data. When only the rods were heated, the data showed very low burnout values in comparison with the results for total uniform heating and round ducts. This disagreement was explained by considering the climbing film flow model and the fact that only a fraction of the channel perimeter was heated. For simultaneous and non-uniform heating of the rods and the shroud it was found that the shroud could be overloaded up to 50 per cent without reducing the margin of safety in respect of burnout for the rod cluster. Finally, a correlation for predicting burnout conditions in round ducts, annuli and rod clusters has been presented. This correlation predicts the burnout heat fluxes for the present measurements and previously obtained annuli measurements within ± 5 per cent

Inference for shared-frailty survival models with left-truncated data

NARCIS (Netherlands)

van den Berg, G.J.; Drepper, B.

2016-01-01

Shared-frailty survival models specify that systematic unobserved determinants of duration outcomes are identical within groups of individuals. We consider random-effects likelihood-based statistical inference if the duration data are subject to left-truncation. Such inference with left-truncated

Reconstitutable control rod spider assembly

International Nuclear Information System (INIS)

Shallenberger, J.M.; Ferian, S.J.

1990-01-01

A reconstitutable control rod/spider assembly includes a hollow connecting finger of the spider having a pair of opposing flat segments formed on the interior thereof and engaging a pair of opposing flat sectors formed on the exterior of a stem extending form the upper end of control rod. The stem also has an externally-threaded portion engaging a nut and a pilot aligning portion for the nut. The nut has a radially flexible and expandable thread-defining element captured in its bore. The segments and sectors allow the rod to be removed and reattached after turning through 180 0 to allow more even wear on the rod. (author)

Estimation of irradiated control rod worth

International Nuclear Information System (INIS)

Varvayanni, M.; Catsaros, N.; Antonopoulos-Domis, M.

2009-01-01

When depleted control rods are planned to be used in new core configurations, their worth has to be accurately predicted in order to deduce key design and safety parameters such as the available shutdown margin. In this work a methodology is suggested for the derivation of the distributed absorbing capacity of a depleted rod, useful in the case that the level of detail that is known about the irradiation history of the control rod does not allow an accurate calculation of the absorber's burnup. The suggested methodology is based on measurements of the rod's worth carried out in the former core configuration and on corresponding calculations based on the original (before first irradiation) absorber concentration. The methodology is formulated for the general case of the multi-group theory; it is successfully tested for the one-group approximation, for a depleted control rod of the Greek Research Reactor, containing five neutron absorbers. The computations reproduce satisfactorily the irradiated rod worth measurements, practically eliminating the discrepancy of the total rod worth, compared to the computations based on the nominal absorber densities.

Rod cluster having improved vane configuration

International Nuclear Information System (INIS)

Shockling, L.A.; Francis, T.A.

1989-01-01

This patent describes a pressurized water reactor vessel, the vessel defining a predetermined axial direction of the flow of coolant therewithin and having plural spider assemblies supporting, for vertical movement within the vessel, respective clusters of rods in spaced, parallel axial relationship, parallel to the predetermined axial direction of coolant flow, and a rod guide for each spider assembly and respective cluster of rods. The rod guide having horizontally oriented support plates therewithin, each plate having an interior opening for accommodating axial movement therethrough of the spider assembly and respective cluster of rods. The opening defining plural radially extending channels and corresponding parallel interior wall surfaces of the support plate

Sucker rod motor

Energy Technology Data Exchange (ETDEWEB)

Radzalov, N N; Radzhabov, N A

1983-01-01

The motor consists of rollers mounted on the wellmouth and connected by a flexible rink. Reciprocating mechanism is in the form of a horizontal non-mobile single-side operation cylinder, inside which a plunger and rod are mounted. The working housing of the hydrocylinder is connected to a gas-hydr aulic batter, and when running is connected via plunger to the high pressure source; running in reverse it is connected with a safety valve and automatic control unit. The unit is equipped with a reducer and a mechanical transformer consisting of screw and nut, and which is shutoff with a single-side lining. The plunger rod consists of an auger-like unit. The high pressure source is provided by the injection line of the sucker rod that has been equipped with a reverse valve.

Duke Power Company's control rod wear program

International Nuclear Information System (INIS)

Culp, D.C.; Kitlan, M.S. Jr.

1990-01-01

Recent examinations performed at several foreign and domestic pressurized water reactors have identified significant control rod cladding wear, leading to the conclusion that previously believed control rod lifetimes are not attainable. To monitor control rod performance and reduce safety concerns associated with wear, Duke Power Company has developed a comprehensive control rod wear program for Ag-In-Cd and boron carbide (B 4 C) rods at the McGuire and Catawba nuclear stations. Duke Power currently uses the Westinghouse 17 x 17 Ag-In-Cd control rod design at McGuire Unit 1 and the Westinghouse 17 x 17 hybrid B 4 C control rod design with a Ag-In-Cd tip at McGuire Unit 2 and Catawba Units 1 and 2. The designs are similar, with the exception of the absorber material and clad thickness. There are 53 control rods per unit

Fuel rod pellet loading head

International Nuclear Information System (INIS)

Howell, T.E.

1975-01-01

An assembly for loading nuclear fuel pellets into a fuel rod comprising a loading head for feeding pellets into the open end of the rod is described. The pellets rest in a perforated substantially V-shaped seat through which air may be drawn for removal of chips and dust. The rod is held in place in an adjustable notched locator which permits alignment with the pellets

Crystallization Mechanism and Phase Transition Properties of W-doped VO2 Synthesized by Hydrothermal Method

Directory of Open Access Journals (Sweden)

LI Yao

2017-11-01

Full Text Available VO2 sol was firstly prepared using vanadyl sulfate as a vanadium source by precipitation-peptization method. Then tungsten(W doping vanadium dioxide(W-VO2 was prepared by hydrothermal crystallization of prepared sol with the presence of ammonium metatungstate. The morphologies, crystal structure of the as-prepared samples and phase transition properties were studied by X-ray diffraction(XRD, field emission scanning electron microscope(FESEMand differential scanning calorimetry(DSC analysis. The results indicate that rod-like W-VO2(B crystal with length of 1-2μm and radius of 100-200nm is firstly formed during hydrothermal treatment for 4-48h at 280℃, then the rod-like crystal dissolves gradually and sheet-like or snowflake-like crystal is formed with the phase transition from W-VO2(B to W-VO2(M and eventually, the W-VO2(M crystals can further grow up while the W-VO2(B gradually dissolves; the phase transition temperature of VO2 decreases with the increase in W doping content, and the phase transition temperature of W-VO2(M reduces to about 28℃ when the nominal dopant concentration is 6.0%(atom fraction.The "nucleation-growth-transformation-ripening" mechanism is proposed as the formation mechanism based on the hydrothermal crystallization and morphological evolution process of W-VO2(M.

Anisotropy in CdSe quantum rods

Energy Technology Data Exchange (ETDEWEB)

Li, Liang-shi [Univ. of California, Berkeley, CA (United States)

2003-01-01

The size-dependent optical and electronic properties of semiconductor nanocrystals have drawn much attention in the past decade, and have been very well understood for spherical ones. The advent of the synthetic methods to make rod-like CdSe nanocrystals with wurtzite structure has offered us a new opportunity to study their properties as functions of their shape. This dissertation includes three main parts: synthesis of CdSe nanorods with tightly controlled widths and lengths, their optical and dielectric properties, and their large-scale assembly, all of which are either directly or indirectly caused by the uniaxial crystallographic structure of wurtzite CdSe. The hexagonal wurtzite structure is believed to be the primary reason for the growth of CdSe nanorods. It represents itself in the kinetic stabilization of the rod-like particles over the spherical ones in the presence of phosphonic acids. By varying the composition of the surfactant mixture used for synthesis we have achieved tight control of the widths and lengths of the nanorods. The synthesis of monodisperse CdSe nanorods enables us to systematically study their size-dependent properties. For example, room temperature single particle fluorescence spectroscopy has shown that nanorods emit linearly polarized photoluminescence. Theoretical calculations have shown that it is due to the crossing between the two highest occupied electronic levels with increasing aspect ratio. We also measured the permanent electric dipole moment of the nanorods with transient electric birefringence technique. Experimental results on nanorods with different sizes show that the dipole moment is linear to the particle volume, indicating that it originates from the non-centrosymmetric hexagonal lattice. The elongation of the nanocrystals also results in the anisotropic inter-particle interaction. One of the consequences is the formation of liquid crystalline phases when the nanorods are dispersed in solvent to a high enough

Immature truncated O-glycophenotype of cancer directly induces oncogenic features

DEFF Research Database (Denmark)

Radhakrishnan, Prakash; Dabelsteen, Sally; Madsen, Frey Brus

2014-01-01

Aberrant expression of immature truncated O-glycans is a characteristic feature observed on virtually all epithelial cancer cells, and a very high frequency is observed in early epithelial premalignant lesions that precede the development of adenocarcinomas. Expression of the truncated O-glycan s...

Probability distributions with truncated, log and bivariate extensions

CERN Document Server

Thomopoulos, Nick T

2018-01-01

This volume presents a concise and practical overview of statistical methods and tables not readily available in other publications. It begins with a review of the commonly used continuous and discrete probability distributions. Several useful distributions that are not so common and less understood are described with examples and applications in full detail: discrete normal, left-partial, right-partial, left-truncated normal, right-truncated normal, lognormal, bivariate normal, and bivariate lognormal. Table values are provided with examples that enable researchers to easily apply the distributions to real applications and sample data. The left- and right-truncated normal distributions offer a wide variety of shapes in contrast to the symmetrically shaped normal distribution, and a newly developed spread ratio enables analysts to determine which of the three distributions best fits a particular set of sample data. The book will be highly useful to anyone who does statistical and probability analysis. This in...

Rod displacement measurements by x-ray CT and its impact on thermal-hydraulics in tight-lattice rod bundle (Joint research)

International Nuclear Information System (INIS)

Mitsutake, Toru; Misawa, Takeharu; Kureta, Masatoshi; Akimoto, Hajime

2005-06-01

In tight-lattice simulated rod bundles with about 1 mm gap between rods, a rod displacement might affect thermal-hydraulic characteristics since the displacement has a strong impact on the flow area change along the heated section. It should be important to estimate how large the rod position displacement could quantitatively affect critical power for the tight-lattice rod bundle from the point of improvement of prediction capability of subchannel analysis. In the present study, the inside-structure observation of the simulated seven-rod bundle of Reduced Moderation Water Reactor (RMWR) was made through the whole length of the test assembly. Based on the measured rod position data, the relation between the rod position displacement and the heat transfer characteristics was investigated experimentally and through the two kinds of subchannel analysis, the nominal rod position case and the measured rod position case, the effect on the predicted critical power was estimated. The high-energy X-ray computer tomograph (CT) of Fuels Monitoring Facilities (FMF) at the O-arai Engineering Center in Japan Nuclear Cycle Institute (JNC) was applied for the inside-structure observation of the test assembly. The CT view of the cross sections within the test assembly assured the hexagonal rod position arrangement was almost the same as expected by design. The measured data with the X-ray CT facility showed that all rod displacements were small, 0.5 millimeters at maximum and 0.2 millimeters in average. In the heat transfer experiments for the seven-rod bundle, the boiling transition (BT) position and the rod surface temperature behavior was measured. All thermocouples on the center rod downstream from the BT-onset axial height showed almost simultaneous temperature increase due to BT. And the thermocouples located on the same axial heights showed quite similar time-variation behaviors in the vapor cooling heat transfer regime. These results demonstrated the effect of the

Impact of degree truncation on the spread of a contagious process on networks.

Science.gov (United States)

Harling, Guy; Onnela, Jukka-Pekka

2018-03-01

Understanding how person-to-person contagious processes spread through a population requires accurate information on connections between population members. However, such connectivity data, when collected via interview, is often incomplete due to partial recall, respondent fatigue or study design, e.g., fixed choice designs (FCD) truncate out-degree by limiting the number of contacts each respondent can report. Past research has shown how FCD truncation affects network properties, but its implications for predicted speed and size of spreading processes remain largely unexplored. To study the impact of degree truncation on predictions of spreading process outcomes, we generated collections of synthetic networks containing specific properties (degree distribution, degree-assortativity, clustering), and also used empirical social network data from 75 villages in Karnataka, India. We simulated FCD using various truncation thresholds and ran a susceptible-infectious-recovered (SIR) process on each network. We found that spreading processes propagated on truncated networks resulted in slower and smaller epidemics, with a sudden decrease in prediction accuracy at a level of truncation that varied by network type. Our results have implications beyond FCD to truncation due to any limited sampling from a larger network. We conclude that knowledge of network structure is important for understanding the accuracy of predictions of process spread on degree truncated networks.

Dynamic rod worth measurements (''Rod Insertion''). Final report for the period 01 December 1994 - 30 November 1996

International Nuclear Information System (INIS)

Bogdan, G.

1996-12-01

Reload startup physics tests are performed for pressurized water reactors (PWR power plant) following a refuelling or other significant core alteration for which nuclear design calculations are required. Part of the reload startup physics tests are control rod group worths measurements. for this purpose a new so-called method ''Rod-Insertion'' was developed. It can also be used as an additional measuring instrument on the research reactor for education purposes. The principle of the rod-insertion method is to start from a critical reactor operating at low power and to measure the time-dependent reactivity change while a control rod is inserted into the core. Unlike in the rod-drop method, the measured control rod is inserted with the drive mechanism at normal speed. By analyzing the flux trace using point-kinetics, not only the total rod worth but also the differential and the integral rod worth curves are obtained. A high-quality electrometer is required for monitoring the neutron flux. The analysis is performed by transferring the data to an IBM PC compatible with some additional standard electronic board and the associated software. The new reactivity meter has been validated on the TRIGA Mark II reactors in Ljubljana and Vienna and at the Krsko Nuclear Power Plant during physics startup tests after reload. The results proved the high performance of the reactivity meter in the standard applications according to the existing procedures, as well as in the new rod-insertion technique of measuring the control rod group worths. This method drastically differs from others such as absence of any chemical control of reactivity (like boron exchange method), and minimizing a testing time and waste coolant production

Control rod ejection analysis during a depressurization accident and the development of a rod-ejection-preventing device

International Nuclear Information System (INIS)

Mitake, S.; Itoh, K.; Fukushima, H.; Inoue, T.

1982-01-01

The control rods used for the experimental VHTR are suspended in the core by means of flexible steel cables and it is conceivable that an accidental rod ejection could occur due to a depressurization accident. The computer code AFLADE was developed in order to analyze the possibility of accidental rod ejection, and several studies were performed. The parametric study results showed that the adopted design condition for the VHTR core will not cause a rod ejection accident. In parallel with these accident analyses, a rod-ejection-preventing device was developed in preparation for a hypothetical accident, and its function was verified by the component tests

Application of a truncated normal failure distribution in reliability testing

Science.gov (United States)

Groves, C., Jr.

1968-01-01

Statistical truncated normal distribution function is applied as a time-to-failure distribution function in equipment reliability estimations. Age-dependent characteristics of the truncated function provide a basis for formulating a system of high-reliability testing that effectively merges statistical, engineering, and cost considerations.

Truncation scheme of time-dependent density-matrix approach II

Energy Technology Data Exchange (ETDEWEB)

Tohyama, Mitsuru [Kyorin University School of Medicine, Mitaka, Tokyo (Japan); Schuck, Peter [Institut de Physique Nucleaire, IN2P3-CNRS, Universite Paris-Sud, Orsay (France); Laboratoire de Physique et de Modelisation des Milieux Condenses, CNRS et Universite Joseph Fourier, Grenoble (France)

2017-09-15

A truncation scheme of the Bogoliubov-Born-Green-Kirkwood-Yvon hierarchy for reduced density matrices, where a three-body density matrix is approximated by two-body density matrices, is improved to take into account a normalization effect. The truncation scheme is tested for the Lipkin model. It is shown that the obtained results are in good agreement with the exact solutions. (orig.)

Investigation of control rod worth and nuclear end of life of BWR control rods

International Nuclear Information System (INIS)

Magnusson, Per

2008-01-01

This work has investigated the Control Rod Worth (CRW) and Nuclear End of Life (NEOL) values for BWR control rods. A study of how different parameters affect NEOL was performed with the transport code PHOENIX4. It was found that NEOL, expressed in terms of 10 B depletion, can be generalized beyond the conditions for which the rod is depleted, such as different power densities and void fractions, the corresponding variation in the NEOL will be about 0.2-0.4% 10 B. It was also found that NEOL results for different fuel types and different fuel enrichments have a variation of about 2-3% in 10 B depletion. A comparative study on NHOL and CRW was made between PHOENIX4 and the stochastic Monte Carlo code MCNP. It was found that there is a significant difference, both due to differences in the codes and to limitations in the geometrical modeling in PHOENIX4. Since MCNP is considered more physically correct, a methodology was developed to calculate the nuclear end of life of BWR control rods with MCNP. The advantages of the methodology are that it does not require other codes to perform the depletion of the absorber material, it can describe control rods of any design and it can deplete the control rod absorber material without burning the fuel. The disadvantage of the method is that is it time-consuming

Multiple-scattering theory with a truncated basis set

International Nuclear Information System (INIS)

Zhang, X.; Butler, W.H.

1992-01-01

Multiple-scattering theory (MST) is an extremely efficient technique for calculating the electronic structure of an assembly of atoms. The wave function in MST is expanded in terms of spherical waves centered on each atom and indexed by their orbital and azimuthal quantum numbers, l and m. The secular equation which determines the characteristic energies can be truncated at a value of the orbital angular momentum l max , for which the higher angular momentum phase shifts, δ l (l>l max ), are sufficiently small. Generally, the wave-function coefficients which are calculated from the secular equation are also truncated at l max . Here we point out that this truncation of the wave function is not necessary and is in fact inconsistent with the truncation of the secular equation. A consistent procedure is described in which the states with higher orbital angular momenta are retained but with their phase shifts set to zero. We show that this treatment gives smooth, continuous, and correctly normalized wave functions and that the total charge density calculated from the corresponding Green function agrees with the Lloyd formula result. We also show that this augmented wave function can be written as a linear combination of Andersen's muffin-tin orbitals in the case of muffin-tin potentials, and can be used to generalize the muffin-tin orbital idea to full-cell potentals

Preliminary nuclear design for test MOX Fuel rods

Energy Technology Data Exchange (ETDEWEB)

Joo, Hyung Kook; Kim, Taek Kyum; Jeong, Hyung Guk; Noh, Jae Man; Cho, Jin Young; Kim, Young Il; Kim, Young Jin; Sohn, Dong Seong

1997-10-01

As a part of activity for future fuel development project, test MOX fuel rods are going to be loaded and irradiated in Halden reactor core as a KAERI`s joint international program with Paul Scherrer Institute (PSI). PSI will fabricate test MOX rods with attrition mill device which was developed by KAERI. The test fuel assembly rig contains three MOX rods and three inert matrix rods. One of three MOX rods will be fabricated by BNFL, the other two MOX fuel rods will be manufacturing jointly by KAERI and PSI. Three inert matrix fuel rods will be fabricated with Zr-Y-Er-Pu oxide. Neutronic evaluation was preliminarily performed for test fuel assembly suggested by PSI. The power distribution of test fuel rod in test fuel assembly was analyzed for various fuel rods position in assembly and the depletion characteristic curve for test fuel was also determined. The fuel rods position in test fuel assembly does not effect the rod power distribution, and the proposal for test fuel rods suggested by PSI is proved to be feasible. (author). 2 refs., 13 tabs., 16 figs.

Single-phase convective heat transfer in rod bundles

International Nuclear Information System (INIS)

Holloway, Mary V.; Beasley, Donald E.; Conner, Michael E.

2008-01-01

The convective heat transfer for turbulent flow through rod bundles representative of nuclear fuel rods used in pressurized water reactors is examined. The rod bundles consist of a square array of parallel rods that are held on a constant pitch by support grids spaced axially along the rod bundle. Split-vane pair support grids, which create swirling flow in the rod bundle, as well as disc and standard support grids are investigated. Single-phase convective heat transfer coefficients are measured for flow downstream of support grids in a rod bundle. The rods are heated using direct resistance heating, and a bulk axial flow of air is used to cool the rods in the rod bundle. Air is used as the working fluid instead of water to reduce the power required to heat the rod bundle. Results indicate heat transfer enhancement for up to 10 hydraulic diameters downstream of the support grids. A general correlation is developed to predict the heat transfer development downstream of support grids. In addition, circumferential variations in heat transfer coefficients result in hot streaks that develop on the rods downstream of split-vane pair support grids

Single-phase convective heat transfer in rod bundles

Energy Technology Data Exchange (ETDEWEB)

Holloway, Mary V. [Mechanical Engineering Department, United States Naval Academy, 590 Holloway Rd., Annapolis, MD 21402 (United States)], E-mail: holloway@usna.edu; Beasley, Donald E. [Mechanical Engineering Department, Clemson University, Clemson, SC 29634 (United States); Conner, Michael E. [Westinghouse Nuclear Fuel, 5801 Bluff Road, Columbia, SC 29250 (United States)

2008-04-15

The convective heat transfer for turbulent flow through rod bundles representative of nuclear fuel rods used in pressurized water reactors is examined. The rod bundles consist of a square array of parallel rods that are held on a constant pitch by support grids spaced axially along the rod bundle. Split-vane pair support grids, which create swirling flow in the rod bundle, as well as disc and standard support grids are investigated. Single-phase convective heat transfer coefficients are measured for flow downstream of support grids in a rod bundle. The rods are heated using direct resistance heating, and a bulk axial flow of air is used to cool the rods in the rod bundle. Air is used as the working fluid instead of water to reduce the power required to heat the rod bundle. Results indicate heat transfer enhancement for up to 10 hydraulic diameters downstream of the support grids. A general correlation is developed to predict the heat transfer development downstream of support grids. In addition, circumferential variations in heat transfer coefficients result in hot streaks that develop on the rods downstream of split-vane pair support grids.

Tuning the crystal morphology and size of zeolitic imidazolate framework-8 in aqueous solution by surfactants

KAUST Repository

Pan, Yichang

2011-01-01

Herein we report a facile synthesis method using surfactant cetyltrimethylammonium bromide (CTAB) as a capping agent for controlling the crystal size and morphology of zeolitic imidazolate framework-8 (ZIF-8) crystals in aqueous systems. The particle sizes can be precisely adjusted from ca. 100 nm to 4 μm, and the morphology can be changed from truncated cubic to rhombic dodecahedron. This journal is © The Royal Society of Chemistry.

The Simulation of Bragg-Case Section Images of Dislocations and Inclusions in Aspect of Identification of Defects in SiC Crystals

International Nuclear Information System (INIS)

Balcer, T.; Wierzchowski, W.; Wieteska, K.

2010-01-01

The numerical simulation has been applied for studying of Bragg-case section topographic images of dislocation and rod-like inclusions. The validity of simple approximation of extinction contrast was confirmed in the case of screw dislocations in silicon carbide crystals. A procedure for approximate calculation of the strain field of rod-like inclusion was constructed, consisting of adding the contributions from a very large number of point-like inclusions uniformly distributed inside the assumed volume of the inclusion. The procedure ensured a reasonable similarity between the simulated topographs and experimental Bragg-case section topographic images of some pipe-formed cavities in silicon carbide crystals. The method is useful for some other materials, e.g. it enabled to compute realistic simulation of plane-wave topographs of the rod-like inclusions in YAG. (authors)

Fabrication of internally instrumented reactor fuel rods

International Nuclear Information System (INIS)

Schmutz, J.D.; Meservey, R.H.

1975-01-01

Procedures are outlined for fabricating internally instrumented reactor fuel rods while maintaining the original quality assurance level of the rods. Instrumented fuel rods described contain fuel centerline thermocouples, ultrasonic thermometers, and pressure tubes for internal rod gas pressure measurements. Descriptions of the thermocouples and ultrasonic thermometers are also contained

Vortex Noise from Rotating Cylindrical Rods

Science.gov (United States)

Stowell, E Z; Deming, A F

1935-01-01

A series of round rods of the some diameter were rotated individually about the mid-point of each rod. Vortices are shed from the rods when in motion, giving rise to the emission of sound. With the rotating system placed in the open air, the distribution of sound in space, the acoustical power output, and the spectral distribution have been studied. The frequency of emission of vortices from any point on the rod is given by the formula von Karman. From the spectrum estimates are made of the distribution of acoustical power along the rod, the amount of air concerned in sound production, the "equivalent size" of the vortices, and the acoustical energy content for each vortex.

Importance-truncated shell model for multi-shell valence spaces

Energy Technology Data Exchange (ETDEWEB)

Stumpf, Christina; Vobig, Klaus; Roth, Robert [Institut fuer Kernphysik, TU Darmstadt (Germany)

2016-07-01

The valence-space shell model is one of the work horses in nuclear structure theory. In traditional applications, shell-model calculations are carried out using effective interactions constructed in a phenomenological framework for rather small valence spaces, typically spanned by one major shell. We improve on this traditional approach addressing two main aspects. First, we use new effective interactions derived in an ab initio approach and, thus, establish a connection to the underlying nuclear interaction providing access to single- and multi-shell valence spaces. Second, we extend the shell model to larger valence spaces by applying an importance-truncation scheme based on a perturbative importance measure. In this way, we reduce the model space to the relevant basis states for the description of a few target eigenstates and solve the eigenvalue problem in this physics-driven truncated model space. In particular multi-shell valence spaces are not tractable otherwise. We combine the importance-truncated shell model with refined extrapolation schemes to approximately recover the exact result. We present first results obtained in the importance-truncated shell model with the newly derived ab initio effective interactions for multi-shell valence spaces, e.g., the sdpf shell.

Vibrational characteristics and wear of fuel rods

International Nuclear Information System (INIS)

Schmugar, K.L.

1977-01-01

Fuel rod wear, due to vibration, is a continuing concern in the design of liquid-cooled reactors. In my report, the methodology and models that are used to predict fuel rod vibrational response and vibratory wear, in a light water reactor environment, are discussed. This methodology is being followed at present in the design of Westinghouse Nuclear Fuel. Fuel rod vibrations are expressed as the normal bending modes, and sources of rod vibration are examined with special emphasis on flow-induced mechanisms in the stable flow region. In a typical Westinghouse PWR fuel assembly design, each fuel rod is supported at multiple locations along the rod axis by a square-shaped 'grid cell'. For a fuel rod /grid support system, the development of small oscillatory motions, due to fluid flow at the rod/grid interface, results in material wear. A theoretical wear mode is developed using the Archard Theory of Adhesive Wear as the basis. Without question certainty, fretting wear becomes a serious problem if it progresses to the stage where the fuel cladding is penetrated and fuel is exposed to the coolant. Westinghouse fuel is designed to minimize fretting wear by limiting the relative motion between the fuel rod and its supports. The wear producing motion between the fuel rod and its supports occurs when the vibration amplitude exceeds the slippage threshold amplitude

Drive-in device for long thin rods into narrow cavitations, especially for control-shutdown rods e.g. of nuclear reactors

International Nuclear Information System (INIS)

Flessner, H.; Paeserack, U.

1974-01-01

The auxiliary device serves as holder for long and thin rods, e.g. control rods, transported hanging in bundles, when these are lowered into narrow cavities. It is constructed as a rod grab vertically movable at the end of a guide tube. A comb-shaped trap in connection with a guide rod serves for lateral support of the lower ends of the rods hanging on the grab. This guide rod can be moved in vertical direction by means of two pairs of convex rollers resting on the inner guide tube. In addition, the guide rod has a prolongation carrying a traverse by means of an abutment on the lower end. With these auxiliaries amongst others, the trap can be brought into a horizontal position by turning around an axis with the control rods meshing with the teeth of the trap while the parallelism of the rods is kept up during transport. (DG) [de

Research in garnet crystal (GSGG) development. Final report, 1 May 1984-31 December 1984

International Nuclear Information System (INIS)

Belt, R.F.; Uhrin, R.; Vemuri, K.

1985-01-01

This program describes the crystal growth of neodymium and chromium doped simultaneously into the host crystal of gadolinium scandium gallium garnet (Nd 3+ , Cr 3 +:Gd 3 (Sc,Ga) 2 Ga 3 O 12 or Nd,Cr:GSGG). Ten experimental boules were grown by the Czochralski method at a diameter of 1.0-1.2 inch. Special attention was given to congruently melting compositions, the Nd and Cr content, growth rate, atmosphere of growth, control of the solid liquid interface, and boule orientation. For each of our crystals a (0.25 x 3.00) inch cylindrical laser rod was extracted, fabricated, tested passively, and delivered to the Lawrence Livermore National Laboratory for active testing. At the same time, boule samples were examined for optical absorption, loss at 1.06μm, refractive index birefringence, and other physical properties. Results have demonstrated that optical quality can approach that of Nd:YAG in rod form. The increased efficiency of Nd,Cr:GSGG was confirmed to be about 2 times that of Nd:YAG. We also show that 2 inch diameter crystal boules can be grown successfully. It appears that larger boules are feasible for slab laser experiments

Control rod excess withdrawal prevention device

International Nuclear Information System (INIS)

Takayama, Yoshihito.

1992-01-01

Excess withdrawal of a control rod of a BWR type reactor is prevented. That is, the device comprises (1) a speed detector for detecting the driving speed of a control rod, (2) a judging circuit for outputting an abnormal signal if the driving speed is greater than a predetermined level and (3) a direction control valve compulsory closing circuit for controlling the driving direction of inserting and withdrawing a control rod based on an abnormal signal. With such a constitution, when the with drawing speed of a control rod is greater than a predetermined level, it is detected by the speed detector and the judging circuit. Then, all of the direction control valve are closed by way of the direction control valve compulsory closing circuit. As a result, the operation of the control rod is stopped compulsorily and the withdrawing speed of the control rod can be lowered to a speed corresponding to that upon gravitational withdrawal. Accordingly, excess withdrawal can be prevented. (I.S)

Flow equation of quantum Einstein gravity in a higher-derivative truncation

International Nuclear Information System (INIS)

Lauscher, O.; Reuter, M.

2002-01-01

Motivated by recent evidence indicating that quantum Einstein gravity (QEG) might be nonperturbatively renormalizable, the exact renormalization group equation of QEG is evaluated in a truncation of theory space which generalizes the Einstein-Hilbert truncation by the inclusion of a higher-derivative term (R 2 ). The beta functions describing the renormalization group flow of the cosmological constant, Newton's constant, and the R 2 coupling are computed explicitly. The fixed point properties of the 3-dimensional flow are investigated, and they are confronted with those of the 2-dimensional Einstein-Hilbert flow. The non-Gaussian fixed point predicted by the latter is found to generalize to a fixed point on the enlarged theory space. In order to test the reliability of the R 2 truncation near this fixed point we analyze the residual scheme dependence of various universal quantities; it turns out to be very weak. The two truncations are compared in detail, and their numerical predictions are found to agree with a surprisingly high precision. Because of the consistency of the results it appears increasingly unlikely that the non-Gaussian fixed point is an artifact of the truncation. If it is present in the exact theory QEG is probably nonperturbatively renormalizable and ''asymptotically safe.'' We discuss how the conformal factor problem of Euclidean gravity manifests itself in the exact renormalization group approach and show that, in the R 2 truncation, the investigation of the fixed point is not afflicted with this problem. Also the Gaussian fixed point of the Einstein-Hilbert truncation is analyzed; it turns out that it does not generalize to a corresponding fixed point on the enlarged theory space

Equipment for manufacture of single crystals by zone overlaying

International Nuclear Information System (INIS)

Richter, O.

1981-01-01

The patented equipment is designed for the manufacture of large-volume monocrystals without the use of a crucible. It consists of a heated backing on which the crystallization nucleus is placed, of a heater element in the form of a plate, rod, strip or prism with bent of tapered ends, and of a proportioning device. The heater element moves along the surface of the growing crystal melting the raw material being supplied and applying it to the whole crystal surface. The bent ends of the heater elements prevent the melt from expanding beyond the limits set by the two moving ends. Using suitably formed heater elements, monocrystals of complex shapes can be produced. (Ha)

Hollow rods for the oil producing industry

Energy Technology Data Exchange (ETDEWEB)

Khalimova, L M; Elyasheva, M A

1970-01-01

Hollow sucker rods have several advantages over conventional ones. The hollow rods actuate the well pump and at the same time conduct produced fluids to surface. When paraffin deposition occurs, it can be minimized by injecting steam, hot oil or hot water into the hollow rod. Other chemicals, such as demulsifiers, scale inhibitors, corrosion inhibitors, etc., can also be placed in the well through the hollow rods. This reduces cost of preventive treatments, reduces number of workovers, increases oil production, and reduces cost of oil. Because the internal area of the rod is small, the passing liquids have a high velocity and thereby carry sand and dirt out of the well. This reduces pump wear between the piston and the plunger. Specifications of hollow rods, their operating characteristics, and results obtained with such rods under various circumstances are described.

Approximate truncation robust computed tomography—ATRACT

International Nuclear Information System (INIS)

Dennerlein, Frank; Maier, Andreas

2013-01-01

We present an approximate truncation robust algorithm to compute tomographic images (ATRACT). This algorithm targets at reconstructing volumetric images from cone-beam projections in scenarios where these projections are highly truncated in each dimension. It thus facilitates reconstructions of small subvolumes of interest, without involving prior knowledge about the object. Our method is readily applicable to medical C-arm imaging, where it may contribute to new clinical workflows together with a considerable reduction of x-ray dose. We give a detailed derivation of ATRACT that starts from the conventional Feldkamp filtered-backprojection algorithm and that involves, as one component, a novel original formula for the inversion of the two-dimensional Radon transform. Discretization and numerical implementation are discussed and reconstruction results from both, simulated projections and first clinical data sets are presented. (paper)

Stellar Disk Truncations: HI Density and Dynamics

Science.gov (United States)

Trujillo, Ignacio; Bakos, Judit

2010-06-01

Using HI Nearby Galaxy Survey (THINGS) 21-cm observations of a sample of nearby (nearly face-on) galaxies we explore whether the stellar disk truncation phenomenon produces any signature either in the HI gas density and/or in the gas dynamics. Recent cosmological simulations suggest that the origin of the break on the surface brightness distribution is produced by the appearance of a warp at the truncation position. This warp should produce a flaring on the gas distribution increasing the velocity dispersion of the HI component beyond the break. We do not find, however, any evidence of this increase in the gas velocity dispersion profile.

ELECTRIC FIELD MEASUREMENT IN ROD-DISCONTINUED ...

African Journals Online (AJOL)

2014-06-30

Jun 30, 2014 ... the electrogeometrical model using a laboratory experimental rod-plane air gap arrangement with a lightning conductor (Franklin rod or horizontal conductor). The stepped leader could be represented by the rod electrode under a negative lightning impulse voltage having a level leading to breakdown with ...

Method of inspecting control rod drive mechanism

International Nuclear Information System (INIS)

Sato, Tomomi; Tatemichi, Shin-ichiro; Hasegawa, Hidenobu.

1988-01-01

Purpose: To conduct inspection for control rod drives and fuel handling operations in parallel without taking out the entire fuel, while maintaining the reactor in a subcritical state. Method: Control rod drives are inspected through the release of connection between control rods and control rod drives, detachment and dismantling of control rod drives, etc. In this case, structural materials having neutron absorbing power equal to or greater than the control rods are inserted into the gap after taking out fuels. Since the structural materials have neutron absorbing portion, subcriticality is maintained by the neutron absorbing effect. Accordingly, there is no requirement for taking out all of the fuels, thereby enabling to check the control rod drives and conduct handling for the fuels in parallel. As a result, the number of days required for the inspection can be shortened and it is possible to improve the working efficiency for the decomposition, inspection, etc. of the control rod drives and, thus, improve the operation efficiency of the nuclear power plant thereby attaining the predetermined purpose. (Kawakami, Y.)

Control rod

International Nuclear Information System (INIS)

Takeda, Toshikazu; Inoue, Kotaro.

1979-01-01

Purpose: To flatten the power distribution in the reactor core without impairing neutron economy by disposing pins containing elements of lower atomic number in the central region of a shroud and loading pins containing depleted uranium in the periphery region thereof. Constitution: The shroud has a layer of pins containing depleted uranium in the peripheral region and a layer of pins containing elements of lower atomic number such as beryllium in the central region. Heat removal from those pins containing depleted uranium and elements of lower atomic number (neutron moderator) is effected by sodium flow outside of the cladding material. The control rod operation is conducted by inserting or extracting the central portion (pins containing elements of lower atomic number such as beryllium) inside of the stainless pipe. Upon extraction of the control rod, the moderator in the central region is removed whereby high speed neutrons are no more deccelerated and the absorption rate to the depleted uranium is decreased. This can flatten the power distribution in the reactore core with the disposition of a plurality of control rods at a better neutron economy as compared with the use of neutron absorber such as boron. (Seki, T.)

Control rod

International Nuclear Information System (INIS)

Fukumoto, Takashi; Hirakawa, Hiromasa; Kawashima, Norio; Goto, Yasuyuki.

1994-01-01

Neutron absorbers are contained in a tubular member comprising, integrally a tubular portion and four corners disposed at the outer circumference of the tubular portion at every 90deg, to provide a neutron absorbing tube. A plurality of neutron absorbing tubes are arranged in parallel in the lateral direction, and adjacent corners are joined, into a blade to constitute a control rod. Such a control rod has a great structural strength, simple in the structure and relatively light in weight and can contain a great amount of neutron absorbers. Upon formation of the control rod by arranging the blades in a cross-like shape, at least a portion thereof is constituted with short neutron absorbing tubes shorter than the entire length of the blade, and gaps are formed at positions in adjacent in the axial direction. With such a constitution, there is no worry that a wing end of the blade collides against or be abraded with a fuel channel box or a fuel support. Even if fuel channels are vibrated upon scram of the reactor, such as occurrence of earthquakes, it can be inserted to the reactor easily. (N.H.)

Experimental determination of temperature fields in sodium-cooled rod bundles with hexagonal rod arrangement and grid spacers

International Nuclear Information System (INIS)

Moeller, R.; Tschoeke, H.; Kolodziej, M.

1977-01-01

Three-dimensional temperature fields in the claddings of sodium cooled rods were determined experimentally under representative nominal operating conditions for a SNR typical 19-rod bundle model provided with spark-eroded spacers. These experiments are required to verify thermohydraulic computer programs which will provide the output data for strength calculations of the high loaded cladding tubes. In this work the essentials are reported of the measured circumferential distributions of wall temperatures of peripheral rods. In addition the sub-channel temperatures measured over the bundle cross section are indicated, they are required to sustain codes for the global thermohydraulic design of core elements. The most important results are: 1) The whole fuel element is located within the thermal entrance length. 2) High azimuthal temperature differences were measured in the claddings of peripheral rods, which are strongly influenced by the distance between the rod and the shroud, especially for the corner rod. 3) With decreasing Pe-number ( [de

Control rod housing alignment

International Nuclear Information System (INIS)

Dixon, R.C.; Deaver, G.A.; Punches, J.R.; Singleton, G.E.; Erbes, J.G.; Offer, H.P.

1990-01-01

This patent describes a process for measuring the vertical alignment between a hole in a core plate and the top of a corresponding control rod drive housing within a boiling water reactor. It comprises: providing an alignment apparatus. The alignment apparatus including a lower end for fitting to the top of the control rod drive housing; an upper end for fitting to the aperture in the core plate, and a leveling means attached to the alignment apparatus to read out the difference in angularity with respect to gravity, and alignment pin registering means for registering to the alignment pin on the core plate; lowering the alignment device on a depending support through a lattice position in the top guide through the hole in the core plate down into registered contact with the top of the control rod drive housing; registering the upper end to the sides of the hole in the core plate; registering the alignment pin registering means to an alignment pin on the core plate to impart to the alignment device the required angularity; and reading out the angle of the control rod drive housing with respect to the hole in the core plate through the leveling devices whereby the angularity of the top of the control rod drive housing with respect to the hole in the core plate can be determined

The Third ATLAS ROD Workshop

CERN Multimedia

Poggioli, L.

A new-style Workshop After two successful ATLAS ROD Workshops dedicated to the ROD hardware and held at the Geneva University in 1998 and in 2000, a new style Workshop took place at LAPP in Annecy on November 14-15, 2002. This time the Workshop was fully dedicated to the ROD-TDAQ integration and software in view of the near future integration activities of the final RODs for the detector assembly and commissioning. More precisely, the aim of this workshop was to get from the sub-detectors the parameters needed for T-DAQ, as well as status and plans from ROD builders. On the other hand, what was decided and assumed had to be stated (like EB decisions and URDs), and also support plans. The Workshop gathered about 70 participants from all ATLAS sub-detectors and the T-DAQ community. The quite dense agenda allowed nevertheless for many lively discussions, and for a dinner in the old town of Annecy. The Sessions The Workshop was organized in five main sessions: Assumptions and recommendations Sub-de...

Temperature actuated automatic safety rod release

Science.gov (United States)

Hutter, E.; Pardini, J.A.; Walker, D.E.

1984-03-13

A temperature-actuated apparatus is disclosed for releasably supporting a safety rod in a nuclear reactor, comprising a safety rod upper adapter having a retention means, a drive shaft which houses the upper adapter, and a bimetallic means supported within the drive shaft and having at least one ledge which engages a retention means of the safety rod upper adapter. A pre-determined increase in temperature causes the bimetallic means to deform so that the ledge disengages from the retention means, whereby the bimetallic means releases the safety rod into the core of the reactor.

Shielding device for control rod in nuclear reactor

International Nuclear Information System (INIS)

Sakamaki, Kazuo; Tomatsu, Tsutomu.

1995-01-01

The device of the present invention shields radiation emitted from control rods to greatly reduce an operator's radiation exposure even if reactor water level is lowered and the upper portion of the control rod is exposed upon inspection of a BWR type reactor. Namely, a shield assembly has a structure comprising a set of four columnar shields in a two-row and two-column arrangement, which can be inserted into a control rod guide tube. Upon conducting inspection, the control rod is lowered into the control rod guide tube, and in this state, the columnar shields of the shield assembly are inserted to the control rod in the control rod guide tube. With such procedures, the upper portion of the control rod protruded from the control rod guide tube is covered with the shield assembly. As a result, radiation leaked from the control rod is shielded. Accordingly, irradiation in the reactor due to leaked radiation can be prevented thereby enabling to reduce an operator's radiation exposure. (I.S.)

Burnable poison rod

International Nuclear Information System (INIS)

Natsume, Tomohiro.

1988-01-01

Purpose: To increase the reactor core lifetime by decreasing the effect of neutron absorption of burnable poison rods by using material with less neutron absorbing effect. Constitution: Stainless steels used so far as the coating material for burnable poison rods have relatively great absorption in the thermal neutral region and are not preferred in view of the neutron economy. Burnable poison rods having fuel can made of zirconium alloy shows absorption the thermal neutron region lower by one digit than that of stainless steels but they shows absorption in the resonance region and the cost is higher. In view of the above, the fuel can of the burnable poison material is made of aluminum or aluminu alloy. This can reduce the neutron absorbing effect by stainless steel fuel can and effectively utilize neutrons that have been wastefully absorbed and consumed in stainless steels. (Takahashi, M.)

Enhancing propagation characteristics of truncated localized waves in silica

KAUST Repository

Salem, Mohamed

2011-07-01

The spectral characteristics of truncated Localized Waves propagating in dispersive silica are analyzed. Numerical experiments show that the immunity of the truncated Localized Waves propagating in dispersive silica to decay and distortion is enhanced as the non-linearity of the relation between the transverse spatial spectral components and the wave vector gets stronger, in contrast to free-space propagating waves, which suffer from early decay and distortion. © 2011 IEEE.

Simulation of leaking fuel rods

International Nuclear Information System (INIS)

Hozer, Z.

2006-01-01

The behaviour of failed fuel rods includes several complex phenomena. The cladding failure initiates the release of fission product from the fuel and in case of large defect even urania grains can be released into the coolant. In steady state conditions an equilibrium - diffusion type - release is expected. During transients the release is driven by a convective type leaching mechanism. There are very few experimental data on leaking WWER fuel rods. For this reason the activity measurements at the nuclear power plants provide very important information. The evaluation of measured data can help in the estimation of failed fuel rod characteristics and the prediction of transient release dynamics in power plant transients. The paper deals with the simulation of leaking fuel rods under steady state and transient conditions and describes the following new results: 1) A new algorithm has been developed for the simulation of leaking fuel rods under steady state conditions and the specific parameters of the model for the Paks NPP has been determined; 2) The steady state model has been applied to calculation of leaking fuel characteristics using iodine and noble gas activity measurement data; 3) A new computational method has been developed for the simulation of leaking fuel rods under transient conditions and the specific parameters for the Paks NPP has been determined; 4) The transient model has been applied to the simulation of shutdown process at the Paks NPP and for the prediction of the time and magnitude of 123 I activity peak; 5) Using Paks NPP data a conservative value has been determined for the upper limit of the 123 I release from failed fuel rods during transients

Control rod for HTGR type reactor

International Nuclear Information System (INIS)

Mogi, Haruyoshi; Saito, Yuji; Fukamichi, Kenjiro.

1990-01-01

Upon dropping control rod elements into the reactor core, impact shocks are applied to wire ropes or spines to possibly deteriorate the integrity of the control rods. In view of the above in the present invention, shock absorbers such as springs or bellows are disposed between a wire rope and a spine in a HTGR type reactor control rod comprising a plurality of control rod elements connected axially by means of a spine that penetrates the central portion thereof, and is suspended at the upper end thereof by a wire rope. Impact shocks of about 5 kg are applied to the wire rope and the spine and, since they can be reduced by the shock absorbers, the control rod integrity can be maintained and the reactor safety can be improved. (T.M.)

Absolute photonic band gap in 2D honeycomb annular photonic crystals

International Nuclear Information System (INIS)

Liu, Dan; Gao, Yihua; Tong, Aihong; Hu, Sen

2015-01-01

Highlights: • A two-dimensional honeycomb annular photonic crystal (PC) is proposed. • The absolute photonic band gap (PBG) is studied. • Annular PCs show larger PBGs than usual air-hole PCs for high refractive index. • Annular PCs with anisotropic rods show large PBGs for low refractive index. • There exist optimal parameters to open largest band gaps. - Abstract: Using the plane wave expansion method, we investigate the effects of structural parameters on absolute photonic band gap (PBG) in two-dimensional honeycomb annular photonic crystals (PCs). The results reveal that the annular PCs possess absolute PBGs that are larger than those of the conventional air-hole PCs only when the refractive index of the material from which the PC is made is equal to 4.5 or larger. If the refractive index is smaller than 4.5, utilization of anisotropic inner rods in honeycomb annular PCs can lead to the formation of larger PBGs. The optimal structural parameters that yield the largest absolute PBGs are obtained

Why Rods and Cocci

Indian Academy of Sciences (India)

Bacteria exhibit a wide variety of shapes but the commonly studied species of bacteria are generally either spherical in shape which are called cocci (singular coccus) or have a cylindrical shape and are called rods or bacilli (singular bacillus). In reality rods and cocci are the ends of a continuum. Sonle of the cocci are.

Spacers for fuel rod clusters

International Nuclear Information System (INIS)

Jabsen, F.S.

1978-01-01

The proposition deals with the fixing of nuclear fuel element rods in a grid which consists of a number of crossed Zy-plates which form cells. The rectangular cells have projections which serve as spacers for the fuel rods. According to the invention there are additional butt straps which can be moved in such a way that insertion and extraction of the fuel rods can be done without obstruction and they can be spring-loaded hold in their final position. (UWI) [de

Rod consolidation at the West Valley Demonstration Project

International Nuclear Information System (INIS)

Bailey, W.J.

1986-12-01

A rod consolidation demonstration with irradiated pressurized water reactor fuel was recently conducted by personnel from Nuclear Assurance Corporation and West Valley Nuclear Services Company at the West Valley Demonstration Project in West Valley, New York. The rod consolidation demonstration involved pulling all of the fuel rods from six fuel Assemblies. In general, the rod pulling proceeded smoothly. The highest compaction ratio attained was 1:8:1. Among the total of 1074 fuel rods were some known degraded rods (they had collapsed cladding, a result of in-reactor fuel densification), but no rods were broken or dropped during the demonstration. One aim was to gather information on the effect of rod consolidation operations on the integrity of the fuel rods during subsequent handling and storage. Another goal was to collect information on the condition and handling of intact, damaged, and failed fuel that has been in storage for an extended period. 9 refs., 8 figs., 1 tab

21 CFR 876.4270 - Colostomy rod.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Colostomy rod. 876.4270 Section 876.4270 Food and... GASTROENTEROLOGY-UROLOGY DEVICES Surgical Devices § 876.4270 Colostomy rod. (a) Identification. A colostomy rod is a device used during the loop colostomy procedure. A loop of colon is surgically brought out through...

Control rod for FBR type reactor

International Nuclear Information System (INIS)

Nakai, Koichi.

1993-01-01

In a control rod for an LMFBR type reactor, a thermal resistor is disposed between a temperature sensitive cylinder and a cam unit support rod. A thermal expansion difference due to the temperature difference is caused between the temperature sensitive cylinder and the cam unit support rod only upon abrupt temperature change of coolants. A control rod shaft extending mechanism of downwardly depressing an absorbent portion by amplifying the thermal expansion difference by an extension link mechanism and the cam unit is provided. The thermal resistor comprises inconel 625 or like other steel of small heat conductivity. If a certain abnormality should cause to the reactor system to elevate the coolant temperature in the reactor elevates abruptly and the reactor shutdown system does not actuate, since the control rod extension shaft extends to urge the absorbent and lower the reactor core reactivity, so that leading to serious accident can be prevented surely. Further, the control rod extension shaft does not extend upon moderate temperature elevation in the usual startup and causes no unnecessary reactivity change. (N.H.)

Design of active-neutron fuel rod scanner

International Nuclear Information System (INIS)

Griffith, G.W.; Menlove, H.O.

1996-01-01

An active-neutron fuel rod scanner has been designed for the assay of fissile materials in mixed oxide fuel rods. A 252 Cf source is located at the center of the scanner very near the through hole for the fuel rods. Spontaneous fission neutrons from the californium are moderated and induce fissions within the passing fuel rod. The rod continues past a combined gamma-ray and neutron shield where delayed gamma rays above 1 MeV are detected. We used the Monte Carlo code MCNP to design the scanner and review optimum materials and geometries. An inhomogeneous beryllium, graphite, and polyethylene moderator has been designed that uses source neutrons much more efficiently than assay systems using polyethylene moderators. Layers of borated polyethylene and tungsten are used to shield the detectors. Large NaI(Tl) detectors were selected to measure the delayed gamma rays. The enrichment zones of a thermal reactor fuel pin could be measured to within 1% counting statistics for practical rod speeds. Applications of the rod scanner include accountability of fissile material for safeguards applications, quality control of the fissile content in a fuel rod, and the verification of reactivity potential for mixed oxide fuels. (orig.)

Hydraulically centered control rod

International Nuclear Information System (INIS)

Horlacher, W.R.; Sampson, W.T.; Schukei, G.E.

1981-01-01

A control rod suspended to reciprocate in a guide tube of a nuclear fuel assembly has a hydraulic bearing formed at its lower tip. The bearing includes a plurality of discrete pockets on its outer surface into which a flow of liquid is continuously provided. In one embodiment the flow is induced by the pressure head in a downward facing chamber at the end of the bearing. In another embodiment the flow originates outside the guide tube. In both embodiments the flow into the pockets produces pressure differences across the bearing which counteract forces tending to drive the rod against the guide tube wall. Thus contact of the rod against the guide tube is avoided

Truncation of CPC solar collectors and its effect on energy collection

Science.gov (United States)

Carvalho, M. J.; Collares-Pereira, M.; Gordon, J. M.; Rabl, A.

1985-01-01

Analytic expressions are derived for the angular acceptance function of two-dimensional compound parabolic concentrator solar collectors (CPC's) of arbitrary degree of truncation. Taking into account the effect of truncation on both optical and thermal losses in real collectors, the increase in monthly and yearly collectible energy is also evaluated. Prior analyses that have ignored the correct behavior of the angular acceptance function at large angles for truncated collectors are shown to be in error by 0-2 percent in calculations of yearly collectible energy for stationary collectors.

Spider and burnable poison rod combinations

International Nuclear Information System (INIS)

Edwards, G.T.; Schluderberg, D.C.

1980-01-01

An improved design of burnable poison rods and associated spiders used in fuel assemblies of pressurized water power reactor cores, is described. The rods are joined to the spider arms in a manner which is proof against the reactor core environment and yet allows the removal of the rods from the spider simply, swiftly and delicately. (U.K.)

Association of a homozygous nonsense mutation in the ABCA4 (ABCR) gene with cone-rod dystrophy phenotype in an Italian family.

Science.gov (United States)

Simonelli, Francesca; Testa, Francesco; Zernant, Jana; Nesti, Anna; Rossi, Settimio; Rinaldi, Ernesto; Allikmets, Rando

2004-01-01

Genetic variation in the ABCA4 (ABCR) gene has been associated with several distinct retinal phenotypes, including Stargardt disease/fundus flavimaculatus (STGD/FFM), cone-rod dystrophy (CRD), retinitis pigmentosa (RP) and age-related macular degeneration. The current model of genotype/phenotype association suggests that patients harboring deleterious mutations in both ABCR alleles would develop RP-like retinal pathology. Here we describe ABCA4-associated phenotypes, including a proband with a homozygous nonsense mutation in a family from Southern Italy. The proband had been originally diagnosed with STGD. Ophthalmologic examination included kinetic perimetry, electrophysiological studies and fluorescein angiography. DNA of the affected individual and family members was analyzed for variants in all 50 exons of the ABCA4 gene by screening on the ABCR400 microarray. A homozygous nonsense mutation 2971G>T (G991X) was detected in a patient initially diagnosed with STGD based on funduscopic evidence, including bull's eye depigmentation of the fovea and flecks at the posterior pole extending to the mid-peripheral retina. Since this novel nucleotide substitution results in a truncated, nonfunctional, ABCA4 protein, the patient was examined in-depth for the severity of the disease phenotype. Indeed, subsequent electrophysiological studies determined severely reduced cone amplitude as compared to the rod amplitude, suggesting the diagnosis of CRD. ABCR400 microarray is an efficient tool for determining causal genetic variation, including new mutations. A homozygous protein-truncating mutation in ABCA4 can cause a phenotype ranging from STGD to CRD as diagnosed at an early stage of the disease. Only a combination of comprehensive genotype/phenotype correlation studies will determine the proper diagnosis and prognosis of ABCA4-associated pathology. Copyright 2004 S. Karger AG, Basel

Modeling and simulation performance of sucker rod beam pump

Energy Technology Data Exchange (ETDEWEB)

Aditsania, Annisa, E-mail: annisaaditsania@gmail.com [Department of Computational Sciences, Institut Teknologi Bandung (Indonesia); Rahmawati, Silvy Dewi, E-mail: silvyarahmawati@gmail.com; Sukarno, Pudjo, E-mail: psukarno@gmail.com [Department of Petroleum Engineering, Institut Teknologi Bandung (Indonesia); Soewono, Edy, E-mail: esoewono@math.itb.ac.id [Department of Mathematics, Institut Teknologi Bandung (Indonesia)

2015-09-30

Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research.

Modeling and simulation performance of sucker rod beam pump

International Nuclear Information System (INIS)

Aditsania, Annisa; Rahmawati, Silvy Dewi; Sukarno, Pudjo; Soewono, Edy

2015-01-01

Artificial lift is a mechanism to lift hydrocarbon, generally petroleum, from a well to surface. This is used in the case that the natural pressure from the reservoir has significantly decreased. Sucker rod beam pumping is a method of artificial lift. Sucker rod beam pump is modeled in this research as a function of geometry of the surface part, the size of sucker rod string, and fluid properties. Besides its length, sucker rod string also classified into tapered and un-tapered. At the beginning of this research, for easy modeling, the sucker rod string was assumed as un-tapered. The assumption proved non-realistic to use. Therefore, the tapered sucker rod string modeling needs building. The numerical solution of this sucker rod beam pump model is computed using finite difference method. The numerical result shows that the peak of polished rod load for sucker rod beam pump unit C-456-D-256-120, for non-tapered sucker rod string is 38504.2 lb, while for tapered rod string is 25723.3 lb. For that reason, to avoid the sucker rod string breaks due to the overload, the use of tapered sucker rod beam string is suggested in this research

Detection device for control rod interference

International Nuclear Information System (INIS)

Saito, Noboru.

1984-01-01

Purpose: To enable to detect the mechanical interference or friction between a control rod and a channel box automatically, simply and rapidly. Constitution: A signal from a gate circuit and a signal from a comparison mechanism are inputted into an AND circuit if a control rod has not been displaced by a predetermined distance within a prescribed time Δt after the output of an insertion or withdrawal signal for the control rod, by which a control-rod-interference signal is outputted from the AND circuit. Accordingly, the interference between the control rod and the channel box can be detected automatically, easily and rapidly. Furthermore, by properly adjusting the prescribed time Δt set by the gate circuit, the degree of the interference can also be detected, whereby the safety and the reliability of the reactor can be improved significantly. (Horiuchi, T.)

Effect of process parameters on crystal size and morphology of lactose in ultrasound-assisted crystallization

Energy Technology Data Exchange (ETDEWEB)

Patel, S.R.; Murthy, Z.V.P. [Chemical Engineering Department, S.V. National Institute of Technology, Surat - 395 007, Gujarat (India)

2011-03-15

{alpha}-lactose monohydrate is widely used as a pharmaceutical excipient. Drug delivery system requires the excipient to be of narrow particle size distribution with regular particle shape. Application of ultrasound is known to increase or decrease the growth rate of certain crystal faces and controls the crystal size distribution. In the present paper, effect of process parameters such as sonication time, anti-solvent concentration, initial lactose concentration and initial pH of sample on lactose crystal size, shape and thermal transition temperature was studied. The parameters were set according to the L{sub 9}-orthogonal array method at three levels and recovered lactose from whey by sonocrystallization. The recovered lactose was analyzed by particle size analyzer, scanning electron microscopy and differential scanning calorimeter. It was found that the morphology of lactose crystal was rod/needle like shape. Crystal size distribution of lactose was observed to be influenced by different process parameters. From the results of analysis of variance, the sonication time interval was found to be the most significant parameter affecting the volume median diameter of lactose with the highest percentage contribution (74.28%) among other parameters. (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Radioactive lightning rods waste treatment

International Nuclear Information System (INIS)

Vicente, Roberto; Dellamano, Jose C.; Hiromoto, Goro

2008-01-01

Full text: In this paper, we present alternative processes that could be adopted for the management of radioactive waste that arises from the replacement of lightning rods with attached Americium-241 sources. Lightning protectors, with Americium-241 sources attached to the air terminals, were manufactured in Brazil until 1989, when the regulatory authority overthrew the license for fabrication, commerce, and installation of radioactive lightning rods. It is estimated that, during the license period, about 75,000 such devices were set up in public, commercial and industrial buildings, including houses and schools. However, the policy of CNEN in regard to the replacement of the installed radioactive rods, has been to leave the decision to municipal governments under local building regulations, requiring only that the replaced rods be sent immediately to one of its research institutes to be treated as radioactive waste. As a consequence, the program of replacement proceeds in a low pace and until now only about twenty thousand rods have reached the waste treatment facilities The process of management that was adopted is based primarily on the assumption that the Am-241 sources will be disposed of as radioactive sealed sources, probably in a deep borehole repository. The process can be described broadly by the following steps: a) Receive and put the lightning rods in initial storage; b) Disassemble the rods and pull out the sources; c) Decontaminate and release the metal parts to metal recycling; d) Store the sources in intermediate storage; e) Package the sources in final disposal packages; and f) Send the sources for final disposal. Up to now, the disassembled devices gave rise to about 90,000 sources which are kept in storage while the design of the final disposal package is in progress. (author)

Snubber assembly for a control rod drive

International Nuclear Information System (INIS)

1976-01-01

A snubber cartridge assembly is described which is mounted to the nozzle of a control rod drive mechanism to insure that it will be located within the liquid filled section of a nuclear reactor vessel whenever the control rod drive is assembled thereto. The snubber assembly includes a piston-mounted proximate to the control rod connecting end of the control rod drive leadscrew to allow the piston to travel within the liquid filled snubber cartridge and controllable exhaust the liquid during a 'scram' condition. The snubber cartridge provides three separate areas of increasing resistance to piston travel to insure a speedy but safe 'scram' of the control rod into the reactor

Automated nuclear fuel rod pattern loading system

International Nuclear Information System (INIS)

Lambert, D.V.; Nyland, T.W.; Byers, J.W.; Haley, D.E. Jr.; Cioffi, J.V.

1990-01-01

This patent describes an apparatus for loading fuel rods in a desired pattern. It comprises: a carousel having a plurality of movable gondolas for stocking thereon fuel rods of known enrichments; an elongated magazine defining a matrix of elongated slots being open at their forward ends for receiving fuel rods; a workstation defining a fuel rod feed path; and a holder and indexing mechanism for movably supporting the magazine and being actuatable for moving the magazine along X-Y axes to successively align one at a time selected ones of the slots with the feed path for loading in the magazine the successive fuel rods in a desired enrichment pattern

Snubber assembly for a control rod drive

International Nuclear Information System (INIS)

Matthews, J.C.

1978-01-01

A snubber cartridge assembly is mounted to the nozzle of a control rod drive mechanism to insure that the snubber assembly will be located within the liquid filled section of a nuclear reactor vessel whenever the control rod drive is assembled thereto. The snubber assembly includes a piston mounted proximate to the control rod connecting end of the control rod drive leadscrew to allow the piston to travel within the liquid filled snubber cartridge and controllably exhaust liquid therefrom during a ''scram'' condition. The snubber cartridge provides three separate areas of increasing resistance to piston travel to insure a speedy but safe ''scram'' of the control rod into the reactor

Method and apparatus for inspection of nuclear fuel rods

International Nuclear Information System (INIS)

Wachter, W.J.

1977-01-01

A method and apparatus are provided for the inspection of nuclear fuel rods to detect defects or failures in such rods. Assemblies of fuel rods are immersed in water and means are provided for causing a change in the relative pressures in the water and within the fuel rod such that fluid is expelled from the rod through any defects that may exist. Means are also provided for thereafter vibrating the rods to cause additional internal fluid or other material that may be trapped in the rod to be expelled. Sensors are provided for detecting the emission of bubbles of fluid or other material from the rod and for locating the position of the defective rod in the assembly. 5 figures

Mechanical properties of bioresorbable self-reinforced posterior cervical rods.

Science.gov (United States)

Savage, Katherine; Sardar, Zeeshan M; Pohjonen, Timo; Sidhu, Gursukhman S; Eachus, Benjamin D; Vaccaro, Alexander

2014-04-01

A biomechanical study. To test the mechanical and physical properties of self-reinforced copolymer bioresorbable posterior cervical rods and compare their mechanical properties to commonly used Irene titanium alloy rods. Bioresorbable instrumentation is becoming increasingly common in surgical spine procedures. Compared with metallic implants, bioresorbable implants are gradually reabsorbed as the bone heals, transferring the load from the instrumentation to bone, eliminating the need for hardware removal. In addition, bioresorbable implants produce less stress shielding due to a more physiological modulus of elasticity. Three types of rods were used: (1) 5.5 mm copolymer rods and (2) 3.5 mm and (3) 5.5 mm titanium alloy rods. Four tests were used on each rod: (1) 3-point bending test, (2) 4-point bending test, (3) shear test, and (4) differential scanning calorimeter test. The outcomes were recorded: Young modulus (E), stiffness, maximum load, deflection at maximum load, load at 1.0% strain of the rod's outer surface, and maximum bending stress. The Young modulus (E) for the copolymer rods (mean range, 6.4-6.8 GPa) was significantly lower than the 3.5 mm titanium rods (106 GPa) and the 5.5 mm titanium rods (95 GPa). The stiffness of the copolymer rods (mean range, 16.6-21.4 N/mm) was also significantly lower than the 3.5 mm titanium alloy rods (43.6 N/mm) and the 5.5 mm titanium alloy rods (239.6 N/mm). The mean maximum shear load of the copolymer rods was 2735 N and they had significantly lower mean maximum loads than the titanium rods. Copolymer rods have adequate shear resistance, but less load resistance and stiffness compared with titanium rods. Their stiffness is closer to that of bone, causing less stress shielding and better gradual dynamic loading. Their use in semirigid posterior stabilization of the cervical spine may be considered.

Implementation of CTRLPOS, a VENTURE module for control rod position criticality searches, control rod worth curve calculations, and general criticality searches

Energy Technology Data Exchange (ETDEWEB)

Smith, L.A.; Renier, J.P.

1994-06-01

A module in the VENTURE reactor analysis code system, CTRLPOS, is developed to position control rods and perform control rod position criticality searches. The module is variably dimensioned so that calculations can be performed with any number of control rod banks each having any number of control rods. CTRLPOS can also calculate control rod worth curves for a single control rod or a bank of control rods. Control rod depletion can be calculated to provide radiation source terms. These radiation source terms can be used to predict radiation doses to personnel and estimate the shielding and long-term storage requirements for spent control rods. All of these operations are completely automated. The numerous features of the module are discussed in detail. The necessary input data for the CTRLPOS module is explained. Several sample problems are presented to show the flexibility of the module. The results presented with the sample problems show that the CTRLPOS module is a powerful tool which allows a wide variety of calculations to be easily performed.

Absorber rod drive for nuclear reactors

International Nuclear Information System (INIS)

Acher, H.

1985-01-01

The invention concerns a further addition to the invention of DE 33 42 830 A1. The free contact of the hollow piston with the nut due to hydraulic pressure is replaced by a hydraulic or spring attachment. The pressure system required to produce the hydraulic pressure is therefore omitted, and the electrical power required for driving the pump or the mass flow is also omitted. The absorber rod slotted along its longitudinal axis is replaced by an absorber rod, in the longitudinal axis of which a hollow piston is connected together with the absorber rod. This makes the absorber rod more stable, and assembly is simplified. (orig./HP) [de

Nuclear reactor fuel rod attachment system

International Nuclear Information System (INIS)

Christiansen, D.W.

1983-01-01

The invention involves a technique to quickly, inexpensively and rigidly attach a nuclear reactor fuel rod to a support member. The invention also allows for the repeated non-destructive removal and replacement of the fuel rod. The proposed fuel rod and support member attachment and removal system consists of a locking cap fastened to the fuel rod and a locking strip fastened to the support member or vice versa. The locking cap has two or more opposing fingers shaped to form a socket. The fingers spring back when moved apart and released. The locking strip has an extension shaped to rigidly attach to the socket's body portion

Transiently truncated and differentially regulated expression of midkine during mouse embryogenesis

International Nuclear Information System (INIS)

Chen Qin; Yuan Yuanyang; Lin Shuibin; Chang Youde; Zhuo Xinming; Wei Wei; Tao Ping; Ruan Lingjuan; Li Qifu; Li Zhixing

2005-01-01

Midkine (MK) is a retinoic acid response cytokine, mostly expressed in embryonic tissues. Aberrant expression of MK was found in numerous cancers. In human, a truncated MK was expressed specifically in tumor/cancer tissues. Here we report the discovery of a novel truncated form of MK transiently expressed during normal mouse embryonic development. In addition, MK is concentrated at the interface between developing epithelium and mesenchyme as well as highly proliferating cells. Its expression, which is closely coordinated with angiogenesis and vasculogenesis, is spatiotemporally regulated with peaks in extensive organogenesis period and undifferentiated cells tailing off in maturing cells, implying its role in nascent blood vessel (endothelial) signaling of tissue differentiation and stem cell renewal/differentiation.. Cloning and sequencing analysis revealed that the embryonic truncated MK, in which the conserved domain is in-frame deleted, presumably producing a novel secreted small peptide, is different from the truncated form in human cancer tissues, whose deletion results in a frame-shift mutation. Our data suggest that MK may play a role in epithelium-mesenchyme interactions, blood vessel signaling, and the decision of proliferation vs differentiation. Detection of the transiently expressed truncated MK reveals its novel function in development and sheds light on its role in carcinogenesis

Modifications of Geometric Truncation of the Scattering Phase Function

Science.gov (United States)

Radkevich, A.

2017-12-01

Phase function (PF) of light scattering on large atmospheric particles has very strong peak in forward direction constituting a challenge for accurate numerical calculations of radiance. Such accurate (and fast) evaluations are important in the problems of remote sensing of the atmosphere. Scaling transformation replaces original PF with a sum of the delta function and a new regular smooth PF. A number of methods to construct such a PF were suggested. Delta-M and delta-fit methods require evaluation of the PF moments which imposes a numerical problem if strongly anisotropic PF is given as a function of angle. Geometric truncation keeps the original PF unchanged outside the forward peak cone replacing it with a constant within the cone. This approach is designed to preserve the asymmetry parameter. It has two disadvantages: 1) PF has discontinuity at the cone; 2) the choice of the cone is subjective, no recommendations were provided on the choice of the truncation angle. This choice affects both truncation fraction and the value of the phase function within the forward cone. Both issues are addressed in this study. A simple functional form of the replacement PF is suggested. This functional form allows for a number of modifications. This study consider 3 versions providing continuous PF. The considered modifications also bear either of three properties: preserve asymmetry parameter, provide continuity of the 1st derivative of the PF, and preserve mean scattering angle. The second problem mentioned above is addressed with a heuristic approach providing unambiguous criterion of selection of the truncation angle. The approach showed good performance on liquid water and ice clouds with different particle size distributions. Suggested modifications were tested on different cloud PFs using both discrete ordinates and Monte Carlo methods. It was showed that the modifications provide better accuracy of the radiance computation compare to the original geometric truncation.

Control device for the withdrawal of control rod

International Nuclear Information System (INIS)

Ando, Masaki.

1985-01-01

Purpose: To significantly suppress the maximum value of the control-rod worth upon control rod withdrawal. Constitution: At first, a signal for designating the first class is sent from a class-control section to the group-control section. In the group-control section, the peripheral group among the first class is designated by which the withdrawal of the control rods other than the peripheral group is inhibited and the control-rods in the peripheral group are withdrawn one by one. When all of them have been withdrawn, the group-control section designates the central group of the first class. All the control rods of the central group have been withdrawn, then the group-control section designates the peripheral group of the second class. Thereafter, the central group in the second class is designated. The control rods are thus withdrawn in the same manner hereinafter. The maximum value for the control-rod worth can be decreased by such a withdrawing sequence for the control rods. (Horiuchi, T.)

Fabrication of BaCO3 Nano-Rods in Water/poly Vinyl Alcohol Mixed Solvents

Science.gov (United States)

Asgari, Motahare; Ataie, Abolghasem; Mokhtabad Amrei, Diba

Barium carbonate nano-particles have been synthesized by a simple PVA-assisted precipitation method using hydrated barium chloride and sodium carbonate as the starting materials. Crystal structure and morphology of the products were evaluated by XRD and SEM techniques, respectively. XRD results indicated that under the identical experimental conditions, single phase BaCO3 was produced. SEM results showed that in the presence of PVA as guide reagent in the solution, nano-rods with regular (facet) surfaces were obtained. The results also showed that the concentration of PVA in the solution, reaction time and temperature have obvious influence on the agglomeration nature and mean particle size of the products. At high concentration of PVA less agglomerated nano size particles of BaCO3 were synthesized. Increasing the synthesis time and temperature resulted in increasing the average diameter of BaCO3 nano-rods. The performance of produced barium carbonate in the processing of barium hexaferrite ceramic magnet via conventional route has been approved.

Control rod drive mechanism

International Nuclear Information System (INIS)

Mizuno, Katsuyuki.

1976-01-01

Object: To restrict the reduction in performance due to stress corrosion cracks by making use of condensate produced in a turbine steam condenser. Structure: Water produced in a turbine steam condenser is forced into a condensed water desalting unit by low pressure condensate pump. The condensate is purified and then forced by a high pressure condensate pump into a feedwater heater for heating before it is returned to the reactor by a feedwater pump. Part of the condensate issuing from the condensate desalting unit is branched from the remaining portion at a point upstream the pump and is withdrawn into a control rod drive water pump after passing through a motordriven bypass valve, an orifice and a condenser water level control valve, is pressurized in the control rod drive water desalting unit and supplied to a control rod drive water pressure system. The control rod is vertically moved by the valve operation of the water pressure system. Since water of high oxygen concentration does not enter during normal operation, it is possible to prevent the stress cracking of the stainless steel apparatus. (Nakamura, S.)

Temperature measurement in cans of fuel rods and fuel rod simulators

International Nuclear Information System (INIS)

Tschoeke, H.; Moeller, R.

1977-01-01

On the sodium-cooled 19-rod cluster model for the SNR 300 the can wall temperature distributions of the non-uniformly cooled rods were measured with thermocouples mounted in outer grooves in the peripheral zone, permitting, in connection with Ni solder, a practically undisturbed measurement. For a more exact determination of the local surface temperature a calibration method, the so-called double-wall method, was developed and applied. The description of this calibration method and the experimental results achieved until now are presented. (orig./RW) [de

A Support Vector Machine Approach for Truncated Fingerprint Image Detection from Sweeping Fingerprint Sensors

Science.gov (United States)

Chen, Chi-Jim; Pai, Tun-Wen; Cheng, Mox

2015-01-01

A sweeping fingerprint sensor converts fingerprints on a row by row basis through image reconstruction techniques. However, a built fingerprint image might appear to be truncated and distorted when the finger was swept across a fingerprint sensor at a non-linear speed. If the truncated fingerprint images were enrolled as reference targets and collected by any automated fingerprint identification system (AFIS), successful prediction rates for fingerprint matching applications would be decreased significantly. In this paper, a novel and effective methodology with low time computational complexity was developed for detecting truncated fingerprints in a real time manner. Several filtering rules were implemented to validate existences of truncated fingerprints. In addition, a machine learning method of supported vector machine (SVM), based on the principle of structural risk minimization, was applied to reject pseudo truncated fingerprints containing similar characteristics of truncated ones. The experimental result has shown that an accuracy rate of 90.7% was achieved by successfully identifying truncated fingerprint images from testing images before AFIS enrollment procedures. The proposed effective and efficient methodology can be extensively applied to all existing fingerprint matching systems as a preliminary quality control prior to construction of fingerprint templates. PMID:25835186

A Support Vector Machine Approach for Truncated Fingerprint Image Detection from Sweeping Fingerprint Sensors

Directory of Open Access Journals (Sweden)

Chi-Jim Chen

2015-03-01

Full Text Available A sweeping fingerprint sensor converts fingerprints on a row by row basis through image reconstruction techniques. However, a built fingerprint image might appear to be truncated and distorted when the finger was swept across a fingerprint sensor at a non-linear speed. If the truncated fingerprint images were enrolled as reference targets and collected by any automated fingerprint identification system (AFIS, successful prediction rates for fingerprint matching applications would be decreased significantly. In this paper, a novel and effective methodology with low time computational complexity was developed for detecting truncated fingerprints in a real time manner. Several filtering rules were implemented to validate existences of truncated fingerprints. In addition, a machine learning method of supported vector machine (SVM, based on the principle of structural risk minimization, was applied to reject pseudo truncated fingerprints containing similar characteristics of truncated ones. The experimental result has shown that an accuracy rate of 90.7% was achieved by successfully identifying truncated fingerprint images from testing images before AFIS enrollment procedures. The proposed effective and efficient methodology can be extensively applied to all existing fingerprint matching systems as a preliminary quality control prior to construction of fingerprint templates.

Propagation of truncated modified Laguerre-Gaussian beams

Science.gov (United States)

Deng, D.; Li, J.; Guo, Q.

2010-01-01

By expanding the circ function into a finite sum of complex Gaussian functions and applying the Collins formula, the propagation of hard-edge diffracted modified Laguerre-Gaussian beams (MLGBs) through a paraxial ABCD system is studied, and the approximate closed-form propagation expression of hard-edge diffracted MLGBs is obtained. The transverse intensity distribution of the MLGB carrying finite power can be characterized by a single bright and symmetric ring during propagation when the aperture radius is very large. Starting from the definition of the generalized truncated second-order moments, the beam quality factor of MLGBs through a hard-edged circular aperture is investigated in a cylindrical coordinate system, which turns out to be dependent on the truncated radius and the beam orders.

Development of cutting device for irradiated fuel rod

International Nuclear Information System (INIS)

Lee, E. P.; Jun, Y. B.; Hong, K. P.; Min, D. K.; Lee, H. K.; Su, H. S.; Kim, K. S.; Kwon, H. M.; Joo, Y. S.; Yoo, K. S.; Joo, J. S.; Kim, E. K.

2004-01-01

Post Irradiation Examination(PIE) on irradiated fuel rods is essential for the evaluation of integrity and irradiation performance of fuel rods of commercial reactor fuel. For PIE, fuel rods should be cut very precisely. The cutting positions selected from NDT data are very important for further destructive examination and analysis. A fuel rod cutting device was developed witch can cut fuel rods longitudinal very precisely and can also cut the fuels into the same length rod cuts repeatedly. It is also easy to remove the fuel cutting powder after cutting works and it can extend the life time of cutting device and lower the contamination level of hot cell

Fabrication Of Control Rod System Of The RSG-GAS

International Nuclear Information System (INIS)

Sudirdjo, Hari; Setyono; Prasetya, Hendra

2001-01-01

Eight units of control rod mechanical system of RSG-GAS has been fabricated. The control rod mechanical system of RSG-GAS consist of guide tube and lifting rod. Complete construction of the control rod mechanical system of RSG-GAS are guide tube, lifting rod, absorber, and absorber casing. The eight units of the control rod mechanical system of RSG-GAS has been fabricated according to the mechanical engineering design

Balanced truncation for linear switched systems

DEFF Research Database (Denmark)

Petreczky, Mihaly; Wisniewski, Rafal; Leth, John-Josef

2013-01-01

In this paper, we present a theoretical analysis of the model reduction algorithm for linear switched systems from Shaker and Wisniewski (2011, 2009) and . This algorithm is a reminiscence of the balanced truncation method for linear parameter varying systems (Wood et al., 1996) [3]. Specifically...

Three-dimensional charge transport in organic semiconductor single crystals.

Science.gov (United States)

He, Tao; Zhang, Xiying; Jia, Jiong; Li, Yexin; Tao, Xutang

2012-04-24

Three-dimensional charge transport anisotropy in organic semiconductor single crystals - both plates and rods (above and below, respectively, in the figure) - is measured in well-performing organic field-effect transistors for the first time. The results provide an excellent model for molecular design and device preparation that leads to good performance. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microcomputer system for controlling fuel rod length

International Nuclear Information System (INIS)

Meyer, E.R.; Bouldin, D.W.; Bolfing, B.J.

1979-01-01

A system is being developed at the Oak Ridge National Laboratory (ORNL) to automatically measure and control the length of fuel rods for use in a high temperature gas-cooled reactor (HTGR). The system utilizes an LSI-11 microcomputer for monitoring fuel rod length and for adjusting the primary factor affecting length. Preliminary results indicate that the automated system can maintain fuel rod length within the specified limits of 1.940 +- 0.040 in. This system provides quality control documentation and eliminates the dependence of the current fuel rod molding process on manual length control. In addition, the microcomputer system is compatible with planned efforts to extend control to fuel rod fissile and fertile material contents

Truncated Newton-Raphson Methods for Quasicontinuum Simulations

National Research Council Canada - National Science Library

Liang, Yu; Kanapady, Ramdev; Chung, Peter W

2006-01-01

.... In this research, we report the effectiveness of the truncated Newton-Raphson method and quasi-Newton method with low-rank Hessian update strategy that are evaluated against the full Newton-Raphson...

The equilibrium crystal shape of nickel

International Nuclear Information System (INIS)

Meltzman, Hila; Chatain, Dominique; Avizemer, Dan; Besmann, Theodore M.; Kaplan, Wayne D.

2011-01-01

Highlights: → The ECS of pure Ni is completely facetted with both dense and high-index planes. → The partial pressure of oxygen has a significant effect on the surface anisotropy. → The addition of Fe decreased the anisotropy and de-stabilized high-index planes. → During solid dewetting nucleation barriers prevent equilibration of the top facet. - Abstract: The crystal shape of Ni particles, dewetted in the solid state on sapphire substrates, was examined as a function of the partial pressure of oxygen (P(O 2 )) and iron content using scanning and transmission electron microscopy. The chemical composition of the surface was characterized by atom-probe tomography. Unlike other face-centered cubic (fcc) equilibrium crystal shapes, the Ni crystals containing little or no impurities exhibited a faceted shape, indicating large surface anisotropy. In addition to the {1 1 1}, {1 0 0} and {1 1 0} facets, which are usually present in the equilibrium crystal shape of fcc metals, high-index facets were identified such as {1 3 5} and {1 3 8} at low P(O 2 ), and {0 1 2} and {0 1 3} at higher P(O 2 ). The presence of iron altered the crystal shape into a truncated sphere with only facets parallel to denser planes. The issue of particle equilibration is discussed specifically for the case of solid-state dewetting.

The Stars and Gas in Outer Parts of Galaxy Disks : Extended or Truncated, Flat or Warped?

NARCIS (Netherlands)

van der Kruit, P. C.; Funes, JG; Corsini, EM

2008-01-01

I review observations of truncations of stellar disks and models for their origin, compare observations of truncations in moderately inclined galaxies to those in edge-on systems and discuss the relation between truncations and H I-warps and their systematics and origin. Truncations are a common

On truncated Taylor series and the position of their spurious zeros

DEFF Research Database (Denmark)

Christiansen, Søren; Madsen, Per A.

2006-01-01

A truncated Taylor series, or a Taylor polynomial, which may appear when treating the motion of gravity water waves, is obtained by truncating an infinite Taylor series for a complex, analytical function. For such a polynomial the position of the complex zeros is considered in case the Taylor...

Advances in Single-Crystal Fibers and Thin Rods Grown by Laser Heated Pedestal Growth

Directory of Open Access Journals (Sweden)

Gisele Maxwell

2017-01-01

Full Text Available Single-crystal fibers are an intermediate between laser crystals and doped glass fibers. They have the advantages of both guiding laser light and matching the efficiencies found in bulk crystals, which is making them ideal candidates for high-power laser and fiber laser applications. This work focuses on the growth of a flexible fiber with a core of dopant (Er, Nd, Yb, etc. and a polycrystalline clad of yttrium aluminum garnet (YAG that will exhibit good wave guiding properties. Direct growth or a combination of growth and cladding experiments are described. Scattering loss measurements at visible wavelengths, along with dopant profile characterization with damage threshold results, are also presented. For single-pass amplification, a single-pass linear gain of 7.4 was obtained for 29 nJ pulses of 5 ns duration at 1 MHz repetition rate. We also obtained a laser efficiency of over 58% in a diode-pumped configuration. These results confirm the potential for single-crystal fibers to overcome the limitations of the glass fibers commonly used in fiber lasers, making them prime candidates for high-power compact fiber lasers and amplifiers.

Control rod for a nuclear reactor

Science.gov (United States)

Roman, Walter G.; Sutton, Jr., Harry G.

1979-01-01

A control rod assembly for a nuclear reactor is disclosed having a remotely disengageable coupling between the control rod and the control rod drive shaft. The coupling is actuated by first lowering then raising the drive shaft. The described motion causes axial repositioning of a pin in a grooved rotatable cylinder, each being attached to different parts of the drive shaft which are axially movable relative to each other. In one embodiment, the relative axial motion of the parts of the drive shaft is used either to couple or to uncouple the connection by forcing resilient members attached to the drive shaft into or out of shouldered engagement, respectively, with an indentation formed in the control rod.

Control rod for a nuclear reactor

International Nuclear Information System (INIS)

Roman, W.G.; Sutton, H.G. Jr.

1976-01-01

A control rod assembly for a nuclear reactor is disclosed having a remotely disengageable coupling between the control rod and the control rod drive shaft. The coupling is actuated by first lowering then raising the drive shaft. The described motion causes axial repositioning of a pin in a grooved rotatable cylinder, each being attached to different parts of the drive shaft which are axially movable relative to each other. In one embodiment, the relative axial motion of the parts of the drive shaft is used either to couple or to uncouple the connection by forcing resilent members attached to the drive shaft into or out of shouldered engagement, respectively, with an indentation formed in the control rod

Control rod for a nuclear reactor

International Nuclear Information System (INIS)

Roman, W.G.; Sutton, H.G. Jr.

1979-01-01

A control rod assembly for a nuclear reactor is disclosed having a remotely disengageable coupling between the control rod and the control rod drive shaft. The coupling is actuated by first lowering then raising the drive shaft. The described motion causes axial repositioning of a pin in a grooved rotatable cylinder, each being attached to different parts of the drive shaft which are axially movable relative to each other. In one embodiment, the relative axial motion of the parts of the drive shaft is used either to couple or to uncouple the connection by forcing resilient members attached to the drive shaft into or out of shouldered engagement, respectively, with an indentation formed in the control rod

ABWR-II Core Design with Spectral Shift Rods for Operation with All Control Rods Withdrawn

International Nuclear Information System (INIS)

Moriwaki, Masanao; Aoyama, Motoo; Anegawa, Takafumi; Okada, Hiroyuki; Sakurada, Koichi; Tanabe, Akira

2004-01-01

An innovative reactor core concept applying spectral shift rods (SSRs) is proposed to improve the plant economy and the operability of the 1700-MW(electric) Advanced Boiling Water Reactor II (ABWR-II). The SSR is a new type of water rod in which a water level is naturally developed during operation and changed according to the coolant flow rate through the channel. By taking advantage of the large size of the ABWR-II bundle, the enhanced spectral shift operation by eight SSRs allows operation of the ABWR-II with all control rods withdrawn. In addition, the uranium-saving factor of 6 to 7% relative to the reference ABWR-II core with conventional water rods can be expected due to the greater effect of spectral shift. The combination of these advantages means the ABWR-II with SSRs should be an attractive alternative for the next-generation nuclear reactor

Process and apparatus for controlling control rods

International Nuclear Information System (INIS)

Gebelin, B.; Couture, R.

1987-01-01

This process and apparatus is characterized by 2 methods, for examination of cluster of nuclear control rods. Foucault current analyzer which examines fraction by fraction all the control rods. This examination is made by rotation of the cluster. Doubtful rods are then analysed by ultrasonic probe [fr

Performance of the NRX shut-off rods

International Nuclear Information System (INIS)

Manson, R.E.

1965-08-01

A new type of shut-off rod of electromechanical design was developed by the American Machine and Foundry Company for use in the NRX reactor following the accident of 1952. The new rods were installed in May, 1956, as part of the control system conversion program which was completed in 1958. Some problems were encountered with limit switch adjustment but minor modifications in design led to much improved operation. he performance of the rods also improved as more experience was gained in the maintenance and adjustment of the various headgear components. Each headgear is now overhauled once a year on a routine basis. The present design of shut-off rod is considered to be very satisfactory. There has only been one occasion when a shut-off rod has failed to come fully down on a trip. Rods have failed to operate correctly on five other occasions but these occurred during shutdown periods or when the reactor was being shutdown manually. (author)

Control rod supporting device in reactor

International Nuclear Information System (INIS)

Seki, Osamu; Itooka, Satoshi; Harada, Kiyoshi; Jodoi, Takashi.

1990-01-01

Since coolants flowing from a reactor core hit against a control rod and a control rod connection pipe, a considerable amount of bending moment for separating an attracting surface between an electromagnet and an armature is formed. Then, a plurality of grooves are formed on a heat sensitive material to dispose a heat collecting fin, and each of upper and lower contact portions of a control rod supporting portion in which the flanged portion of T-like cross section does not slip out is made into a partial spheric surface and a portion between the electromagnet and the attracted member are engaged by the unevenness. With such a constitution, even if a bending moment is applied, the control rod only swings and the bending moment is not transmitted to the attracted member. Further, since the temperature of the heat sensitive material can be rapidly made closer to the peripheral temperature by using the heat collecting fin, the timing for separation is made accurate. Further, since the engaging portion is brought into contact at the spheric surface, the load distribution on the control rod is made uniform, and the positional relationship is made accurate, to support the control rod reliably and the separation depends only on the temperature of the coolants. (N.H.)

Expression, purification, crystallization and preliminary crystallographic analysis of MxiH, a subunit of the Shigella flexneri type III secretion system needle

International Nuclear Information System (INIS)

Deane, Janet E.; Cordes, Frank S.; Roversi, Pietro; Johnson, Steven; Kenjale, Roma; Picking, William D.; Picking, Wendy L.; Lea, Susan M.; Blocker, Ariel

2006-01-01

A monodisperse truncation mutant of MxiH, the subunit of the S. flexneri type III secretion system needle, has been crystallized. SeMet derivatives and a uranyl derivative have undergone preliminary crystallographic analysis. A monodisperse truncation mutant of MxiH, the subunit of the needle from the Shigella flexneri type III secretion system (TTSS), has been overexpressed and purified. Crystals were grown of native and selenomethionine-labelled MxiH CΔ5 and diffraction data were collected to 1.9 Å resolution. The crystals belong to space group C2, with unit-cell parameters a = 183.4, b = 28.1, c = 27.8 Å, β = 96.5°. An anomalous difference Patterson map calculated with the data from the SeMet-labelled crystals revealed a single peak on the Harker section v = 0. Inspection of a uranyl derivative also revealed one peak in the isomorphous difference Patterson map on the Harker section v = 0. Analysis of the self-rotation function indicates the presence of a twofold non-crystallographic symmetry axis approximately along a. The calculated Matthews coefficient is 1.9 Å 3 Da −1 for two molecules per asymmetric unit, corresponding to a solvent content of 33%

Cuisenaire Rods Go to College.

Science.gov (United States)

Chinn, Phyllis; And Others

1992-01-01

Presents examples of questions and answers arising from a hands-on and exploratory approach to discrete mathematics using cuisenaire rods. Combinatorial questions about trains formed of cuisenaire rods provide the setting for discovering numerical patterns by experimentation and organizing the results using induction and successive differences.…

Control rod driving mechanism

International Nuclear Information System (INIS)

Ooshima, Yoshio.

1983-01-01

Purpose: To perform reliable scram operation, even if abnormality should occur in a system instructing scram operation in FBR type reactors. Constitution: An aluminum alloy member to be melt at a predetermined temperature (about 600sup(o)C) is disposed to a connection part between a control rod and a driving mechanism, whereby the control rod is detached from the driving mechanism and gravitationally fallen to the reactor core. (Ikeda, J.)

Expandable device for a nuclear fuel rod

International Nuclear Information System (INIS)

Gesinski, L.T.

1978-01-01

A nuclear fuel rod and a device for use within the rod cladding to maintain the axial position of the fuel pellets stacked one atop another within the cladding are described. The device is initially of a smaller external cross-section than the fuel rod cladding internal cross-section so as to accommodate loading into the rod at preselected locations. During power operation the device responds to a rise in temperature, so as to permanently maintain its position and restrain any axial motion of the fuel pellets

Controlled synthesis of SrCrO4 crystals with different morphologies

International Nuclear Information System (INIS)

Yang, Xiao-Hong; Wu, Qing-Sheng; Liu, Jin-Ku

2007-01-01

Rod-shape, branch-shape, bouquet-shape and claw-shape SrCrO 4 crystals were synthesized through biomembrane/organic-addition supramolecular templates. The shapes are mainly changed with variance of the organic reagents and organic membranes. Most of the morphologies haven't been reported in the literature. This method may meet with the requirements to synthesize materials of various morphologies and size by using different supramolecular templates. This paper discusses how to control crystals' growth by supramolecular templates. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Method and apparatus for compacting spent nuclear reactor fuel rods

International Nuclear Information System (INIS)

Wachter, W.J.

1988-01-01

In a nuclear reactor system requiring periodic physical manipulation of spent fuel rods, the method of compacting fuel rods from a fuel rod assembly is described comprising the steps of: (1) removing the top end from pulling members having electrodes of weld elements in leading ends thereof in sequence through a fuel rod container and thence through respective consolidating passages in a fuel-rod directing chamber; (3) welding the weld elements of the pulling members to the top end of respective fuel rods corresponding to the respective pulling members; (4) drawing each of the pulling members axially to draw the respective engaged fuel rods in one axial direction through the respective passages in the chamber to thereby consolidate the fuel rods into a compacted configuration of a cross-sectional area smaller than the cross-sectional area occupied thereby within the fuel rod assembly; and (5) drawing all of the engaged fuel rods concurrently and substantially parallel to one another to the one axial direction into the fuel rod container while maintaining the compacting configuration in a fuel rod density which is greater than that of the fuel rod density of the fuel rod assembly

Closed-form kinetic parameter estimation solution to the truncated data problem

International Nuclear Information System (INIS)

Zeng, Gengsheng L; Kadrmas, Dan J; Gullberg, Grant T

2010-01-01

In a dedicated cardiac single photon emission computed tomography (SPECT) system, the detectors are focused on the heart and the background is truncated in the projections. Reconstruction using truncated data results in biased images, leading to inaccurate kinetic parameter estimates. This paper has developed a closed-form kinetic parameter estimation solution to the dynamic emission imaging problem. This solution is insensitive to the bias in the reconstructed images that is caused by the projection data truncation. This paper introduces two new ideas: (1) it includes background bias as an additional parameter to estimate, and (2) it presents a closed-form solution for compartment models. The method is based on the following two assumptions: (i) the amount of the bias is directly proportional to the truncated activities in the projection data, and (ii) the background concentration is directly proportional to the concentration in the myocardium. In other words, the method assumes that the image slice contains only the heart and the background, without other organs, that the heart is not truncated, and that the background radioactivity is directly proportional to the radioactivity in the blood pool. As long as the background activity can be modeled, the proposed method is applicable regardless of the number of compartments in the model. For simplicity, the proposed method is presented and verified using a single compartment model with computer simulations using both noiseless and noisy projections.

Analytic reconstruction algorithms for triple-source CT with horizontal data truncation

International Nuclear Information System (INIS)

Chen, Ming; Yu, Hengyong

2015-01-01

Purpose: This paper explores a triple-source imaging method with horizontal data truncation to enlarge the field of view (FOV) for big objects. Methods: The study is conducted by using theoretical analysis, mathematical deduction, and numerical simulations. The proposed algorithms are implemented in c + + and MATLAB. While the basic platform is constructed in MATLAB, the computationally intensive segments are coded in c + +, which are linked via a MEX interface. Results: A triple-source circular scanning configuration with horizontal data truncation is developed, where three pairs of x-ray sources and detectors are unevenly distributed on the same circle to cover the whole imaging object. For this triple-source configuration, a fan-beam filtered backprojection-type algorithm is derived for truncated full-scan projections without data rebinning. The algorithm is also extended for horizontally truncated half-scan projections and cone-beam projections in a Feldkamp-type framework. Using their method, the FOV is enlarged twofold to threefold to scan bigger objects with high speed and quality. The numerical simulation results confirm the correctness and effectiveness of the developed algorithms. Conclusions: The triple-source scanning configuration with horizontal data truncation cannot only keep most of the advantages of a traditional multisource system but also cover a larger FOV for big imaging objects. In addition, because the filtering is shift-invariant, the proposed algorithms are very fast and easily parallelized on graphic processing units

Two-Dimentional Photonic Crystal Waveguides

DEFF Research Database (Denmark)

Søndergaard, Thomas; Dridi, Kim

1999-01-01

possible a novel class of optical microcavities, whereas line defects make possible a novel class of waveguides. In this paper we will analyze two-dimensional photonic crystal waveguides based on photonic crystals with rods arranged on a triangular and a square lattice using a plane-wave expansion method......In the recent years a new class of periodic high-index contrast dielectric structures, known as photonic bandgap structures, has been discovered. In these structures frequency intervals, known as photonic bandgaps, where propagation of electromagnetic waves is not allowed, exist due to the periodic...... dielectric function. This is analogous to semiconductors, where electronic bandgaps exist due to the periodic arrangement of atoms. As is also the case for semiconductor structures, photonic bandgap structures may become of even greater value when defects are introduced. In particular, point defects make...

Energy cascade with small-scale thermalization, counterflow metastability, and anomalous velocity of vortex rings in Fourier-truncated Gross-Pitaevskii equation

International Nuclear Information System (INIS)

Krstulovic, Giorgio; Brachet, Marc

2011-01-01

The statistical equilibria of the (conservative) dynamics of the Gross-Pitaevskii equation (GPE) with a finite range of spatial Fourier modes are characterized using a new algorithm, based on a stochastically forced Ginzburg-Landau equation (SGLE), that directly generates grand-canonical distributions. The SGLE-generated distributions are validated against finite-temperature GPE-thermalized states and exact (low-temperature) results obtained by steepest descent on the (grand-canonical) partition function. A standard finite-temperature second-order λ transition is exhibited. A mechanism of GPE thermalization through a direct cascade of energy is found using initial conditions with mass and energy distributed at large scales. A long transient with partial thermalization at small scales is observed before the system reaches equilibrium. Vortices are shown to disappear as a prelude to final thermalization and their annihilation is related to the contraction of vortex rings due to mutual friction. Increasing the amount of dispersion at the truncation wave number is shown to slow thermalization and vortex annihilation. A bottleneck that produces spontaneous effective self-truncation with partial thermalization is characterized in the limit of large dispersive effects. Metastable counterflow states, with nonzero values of momentum, are generated using the SGLE algorithm. Spontaneous nucleation of the vortex ring is observed and the corresponding Arrhenius law is characterized. Dynamical counterflow effects on vortex evolution are investigated using two exact solutions of the GPE: traveling vortex rings and a motionless crystal-like lattice of vortex lines. Longitudinal effects are produced and measured on the crystal lattice. A dilatation of vortex rings is obtained for counterflows larger than their translational velocity. The vortex ring translational velocity has a dependence on temperature that is an order of magnitude above that of the crystal lattice, an effect

Shock analysis on hydraulic drive control rod during scram

International Nuclear Information System (INIS)

Song Wei; Qin Benke; Bo Hanliang

2013-01-01

Control rod hydraulic drive mechanism (CRHDM) is a new invention of Institute of Nuclear and New Energy Technology of Tsinghua University. The hydraulic absorber buffers the control rod when it scrams. The control rod fast drop impact experiment was conducted and the key parameters of control rod hydraulic buffering performance were obtained. Based on the test results and according to D'Alembert principle, the maximum inertial impact force on the control rod during the fast drop period was applied as equivalent static load force on the control rod. The deformations and stress distributions on the control rod in this worst case were calculated by using finite element software ABAQUS. Calculation results were compared with the experiment results, and it was verified that nonlinear transient dynamics analysis in this problem can be simplified as static analysis. Damage criterion of the control rod fast drop impact process was also given. And it lays foundation for optimal design of the control rod and hydraulic absorber. (authors)

A Line Search Multilevel Truncated Newton Algorithm for Computing the Optical Flow

Directory of Open Access Journals (Sweden)

Lluís Garrido

2015-06-01

Full Text Available We describe the implementation details and give the experimental results of three optimization algorithms for dense optical flow computation. In particular, using a line search strategy, we evaluate the performance of the unilevel truncated Newton method (LSTN, a multiresolution truncated Newton (MR/LSTN and a full multigrid truncated Newton (FMG/LSTN. We use three image sequences and four models of optical flow for performance evaluation. The FMG/LSTN algorithm is shown to lead to better optical flow estimation with less computational work than both the LSTN and MR/LSTN algorithms.

Acoustic loading effects on oscillating rod bundles

International Nuclear Information System (INIS)

Lin, W.H.

1980-01-01

An analytical study of the interaction between an infinite acoustic medium and a cluster of circular rods is described. The acoustic field due to oscillating rods and the acoustic loading on the rods are first solved in a closed form. The acoustic loading is then used as a forcing function for rod responses, and the acousto-elastic couplings are solved simultaneously. Numerical examples are presented for several cases to illustrate the effects of various system parameters on the acoustic reaction force coefficients. The effect of the acoustic loading on the coupled eigenfrequencies are discussed

Control Rod Malfunction at the NRAD Reactor

Energy Technology Data Exchange (ETDEWEB)

Thomas L. Maddock

2010-05-01

The neutron Radiography Reactor (NRAD) is a training, research, and isotope (TRIGA) reactor located at the INL. The reactor is normally shut down by the insertion of three control rods that drop into the core when power is removed from electromagnets. During a routine shutdown, indicator lights on the console showed that one of the control rods was not inserted. It was initially thought that the indicator lights were in error because of a limit switch that was out of adjustment. Through further testing, it was determined that the control rod did not drop when the scram switch was initially pressed. The control rod anomaly led to a six month shutdown of the reactor and an in depth investigation of the reactor protective system. The investigation looked into: scram switch operation, console modifications, and control rod drive mechanisms. A number of latent issues were discovered and corrected during the investigation. The cause of the control rod malfunction was found to be a buildup of corrosion in the control rod drive mechanism. The investigation resulted in modifications to equipment, changes to both operation and maintenance procedures, and additional training. No reoccurrences of the problem have been observed since corrective actions were implemented.

Low-mode truncation methods in the sine-Gordon equation

International Nuclear Information System (INIS)

Xiong Chuyu.

1991-01-01

In this dissertation, the author studies the chaotic and coherent motions (i.e., low-dimensional chaotic attractor) in some near integrable partial differential equations, particularly the sine-Gordon equation and the nonlinear Schroedinger equation. In order to study the motions, he uses low mode truncation methods to reduce these partial differential equations to some truncated models (low-dimensional ordinary differential equations). By applying many methods available to low-dimensional ordinary differential equations, he can understand the low-dimensional chaotic attractor of PDE's much better. However, there are two important questions one needs to answer: (1) How many modes is good enough for the low mode truncated models to capture the dynamics uniformly? (2) Is the chaotic attractor in a low mode truncated model close to the chaotic attractor in the original PDE? And how close is? He has developed two groups of powerful methods to help to answer these two questions. They are the computation methods of continuation and local bifurcation, and local Lyapunov exponents and Lyapunov exponents. Using these methods, he concludes that the 2N-nls ODE is a good model for the sine-Gordon equation and the nonlinear Schroedinger equation provided one chooses a 'good' basis and uses 'enough' modes (where 'enough' depends on the parameters of the system but is small for the parameter studied here). Therefore, one can use 2N-nls ODE to study the chaos of PDE's in more depth

A 2D Rods-in-Air Square-Lattice Photonic Crystal Optical Switch

Science.gov (United States)

2009-03-01

4] Tao Chu, Hirohito Yamada, Satomi Ishida, Yasuhiko Arakawa, Thermooptic switch based on photonic-crystal line-defect waveguides, IEEE Photon...Ishida, Yasuhiko Arakawa, Hiroyuki Fujita, Hiroshi Toshiyoshi, Design and fabrication on MEMS optical mod- ulators integrated with Phc waveguide, in

Expression, purification, crystallization and preliminary X-ray studies of Vibrio cholerae pseudopilin EpsH

International Nuclear Information System (INIS)

Raghunathan, Kannan; Vago, Frank S.; Ball, Terry; Yakubova, Nafissa; Grindem, David; Wedemeyer, William J.; Arvidson, Dennis N.

2009-01-01

Recombinant V. cholerae EpsH has been expressed, purified and crystallized. The crystals diffracted to 1.71 Å resolution. EpsH is a minor pseudopilin protein of the Vibrio cholerae type II secretion system. A truncated form of EpsH with a C-terminal noncleavable His tag was constructed and expressed in Escherichia coli, purified and crystallized by sitting-drop vapor diffusion. A complete data set was collected to 1.71 Å resolution. The crystals belonged to space group P2 1 2 1 2 1 , with unit-cell parameters a = 53.39, b = 71.11, c = 84.64 Å. There were two protein molecules in the asymmetric unit, which gave a Matthews coefficient V M of 2.1 Å 3 Da −1 , corresponding to 41.5% solvent content

Control rod driving hydraulic pressure device

International Nuclear Information System (INIS)

Ishida, Kazuo.

1990-01-01

Discharged water after actuating control rod drives in a BWR type reactor is once discharged to a discharging header, then returned to a master control unit and, subsequently, discharged to a reactor by way of a cooling water header. The radioactive level in the discharging header and the master control unit is increased by the reactor water to increase the operator's exposure. In view of the above, a riser is disposed for connecting a hydraulic pressure control unit incorporating a directional control valve and the cooling water head. When a certain control rod is inserted, the pressurized driving water is supplied through a hydraulic pressure control unit to the control rod drives. The discharged water from the control rod drives is entered by way of the hydraulic pressure control unit into the cooling water header and then returned to the reactor by way of other hydraulic pressure control unit and the control rod drives. Thus, the reactor water is no more recycled to the master control unit to reduce the radioactive exposure. (N.H.)

Nuclear reactor with scrammable part length rod

International Nuclear Information System (INIS)

Bevilacqua, F.

1979-01-01

A new part length rod is provided. It may be used to control xenon induced power oscillations but to contribute to shutdown reactivity when a rapid shutdown of the reactor is required. The part length rod consists of a control rod with three regions. The lower control region is a longer weaker active portion separated from an upper stronger shorter poison section by an intermediate section which is a relative non-absorber of neutrons. The combination of the longer weaker control section with the upper high worth poison section permits the part length rod of this to be scrammed into the core when a reactor shutdown is required but also permits the control rod to be used as a tool to control power distribution in both the axial and radial directions during normal operation

Apparatus for loading fuel pellets in fuel rods

International Nuclear Information System (INIS)

Tedesco, R.J.

1976-01-01

An apparatus is disclosed for loading fuel pellets into fuel rods for a nuclear reactor including a base supporting a table having grooves therein for holding a multiplicity of pellets. Multiple fuel rods are placed in alignment with grooves in the pellet table and a guide member channels pellets from the table into the corresponding fuel rods. To effect movement of pellets inside the fuel rods without jamming, a number of electromechanical devices mounted on the base have arms connected to the lower surface of the fuel rod table which cyclically imparts a reciprocating arc motion to the table for moving the fuel pellets longitudinally of and inside the fuel rods. These electromechanical devices include a solenoid having a plunger therein connected to a leaf type spring, the arrangement being such that upon energization of the solenoid coil, the leaf spring moves the fuel rod table rearwardly and downwardly, and upon deenergization of the coil, the spring imparts an upward-forward movement to the table which results in physical displacement of fuel pellets in the fuel rods clamped to the table surface. 8 claims, 6 drawing figures

Control rod housing alignment and repair apparatus

International Nuclear Information System (INIS)

Dixon, R.C.; Deaver, G.A.; Punches, J.R.; Singleton, G.E.; Erbes, J.G.; Offer, H.P.

1991-01-01

This patent describes a welding a repair device for precisely locating and welding the position of the top of a control rod drive housing attached from a stub tube from a corresponding aperture and alignment pin in a core plate within a boiling water nuclear reactor, the welding and repair device. It comprises: a shaft, the shaft extending from the vicinity of the top of the control rod drive housing up to and through the aperture in the core plate; means for registering to the aperture and the alignment pin on the core plate; a fixture attached to the bottom end of the shaft for mating to the top of the control rod drive housing in precise mating relationship; the fixture attached to the bottom end of the shaft whereby the fixture, when mated to the control rod drove housing and the registering means when registered to the alignment pin and aperture on the core plate imparts to the shaft, and angularity between the top of the control rod drive housing and the hole in the core plate; a hollow cylinder, the cylinder mounted for depending and sealed support with respect to the shaft above, about and below the control rod drive housing top; the cylinder depending down below the control rod drive housing to an elevation below the top of the sub tube; a rotating welding apparatus with a welding head for dispensing weldment mounted for rotation with respect to the shaft; the welding head disposed at the juncture between the side of the control rod drive housing and the stub tube; and means for flooding the cylinder with gas whereby the cylinder may be lowered. flooded in a gas environment and effect a weld between the top of the stub tube and the control rod drive housing

Control rod housing alignment and repair method

International Nuclear Information System (INIS)

Dixon, R.C.; Deaver, G.A.; Punches, J.R.; Singleton, G.E.; Erbes, J.G.; Offer, H.P.

1992-01-01

This patent describes a method for underwater welding of a control rod drive housing inserted through a stub tube to maintain requisite alignment and elevation of the top of the control rod drive housing to an overlying and corresponding aperture in a core plate as measured by an alignment device which determines the relative elevation and angularity with respect to the aperture. It comprises providing a welding cylinder dependent from the alignment device such that the elevation of the top of the welding cylinder is in a fixed relationship to the alignment device and is gas-proof; pressurizing the welding cylinder with inert welding gas sufficient to maintain the interior of the welding cylinder dry; lowering the welding cylinder through the aperture in the core plate by depending the cylinder with respect to the alignment device, the lowering including lowering through and adjusting the elevation relationship of the welding cylinder to the alignment device such that when the alignment device is in position to measure the elevation and angularity of the new control rod drive housing, the lower distal end of the welding cylinder extends below the upper periphery of the stub where welding is to occur; inserting a new control rod drive housing through the stub tube and positioning the control rod drive housing to a predetermined relationship to the anticipated final position of the control rod drive housing; providing welding implements transversely rotatably mounted interior of the welding cylinder relative to the alignment device such that the welding implements may be accurately positioned for dispensing weldment around the periphery of the top of the stub tube and at the side of the control rod drive housing; measuring the elevation and angularity of the control rod drive housing; and dispensing weldment along the top of the stub tube and at the side of the control rod drive housing

N-terminally truncated POM121C inhibits HIV-1 replication.

Directory of Open Access Journals (Sweden)

Hideki Saito

Full Text Available Recent studies have identified host cell factors that regulate early stages of HIV-1 infection including viral cDNA synthesis and orientation of the HIV-1 capsid (CA core toward the nuclear envelope, but it remains unclear how viral DNA is imported through the nuclear pore and guided to the host chromosomal DNA. Here, we demonstrate that N-terminally truncated POM121C, a component of the nuclear pore complex, blocks HIV-1 infection. This truncated protein is predominantly localized in the cytoplasm, does not bind to CA, does not affect viral cDNA synthesis, reduces the formation of 2-LTR and diminished the amount of integrated proviral DNA. Studies with an HIV-1-murine leukemia virus (MLV chimeric virus carrying the MLV-derived Gag revealed that Gag is a determinant of this inhibition. Intriguingly, mutational studies have revealed that the blockade by N-terminally-truncated POM121C is closely linked to its binding to importin-β/karyopherin subunit beta 1 (KPNB1. These results indicate that N-terminally-truncated POM121C inhibits HIV-1 infection after completion of reverse transcription and before integration, and suggest an important role for KPNB1 in HIV-1 replication.

Processing of poison rods with a view to disposal

International Nuclear Information System (INIS)

Bichet, R.; Charamathieu, A.; Lasseur, C.; Golicheff, I.; Pouteaux, M.

1979-01-01

In the core of the French 900 and 1300 MW reactors, a certain number of rods have to be processed as wastes, particularly the burnable poison rods used during reactor start-up (900 MW: 68 rods; 1300 MW: 96 rods). Several solutions are possible: cutting and conditionning in reactor pool; transfer of the poison rods to a cutting and conditionning facility; transfer of the poison rods and fuel assemblies to a storage area where they are cutted and stored. Each of these solutions are studied, the advantages and disadvantages being presented

Characterization of Emericella nidulans RodA and DewA hydrophobin mutants

DEFF Research Database (Denmark)

Jensen, Britt Guillaume; Nielsen, Jakob Blæsbjerg; Pedersen, Mona Højgaard

hydrophobins RodA and DewA. Individual knock-out mutants rodAΔ, dewAΔ and the double deletion strain rodAΔdewAΔ were constructed. Furthermore, two strains containing a point mutation in the first of the cysteines of RodA (rodA-C57G), where one was coupled to the dewA deletion, were included. The reference...... strain (NID1) and dewAΔ displayed green conidia. However, rodAΔ and rodAΔdewAΔ showed a dark green/brown conidial pigmentation, while rodA-C57G and rodAC57G dewAΔ displayed lighter brown conidia. rodAΔ and rodAΔdewAΔ displayed a higher degree of hülle cells compared to the moderate amount observed...... for NID1 and dewAΔ, while rodA-C57G and rodA-C57G dewAΔ displayed a low number of hülle cells. NID1 and dewAΔ conidia were dispersed as spore chains. rodAΔ, rodAΔdewAΔ, rodA-C57G and rodA-C57G dewAΔ spores were associated in large clumps, where the conidia seemed to adhere to one another. The largest...

Formation and crystallization kinetics of Nd-Fe-B-based bulk amorphous alloy

Energy Technology Data Exchange (ETDEWEB)

Wu, Qiong; Ge, Hongliang; Zhang, Pengyue; Li, Dongyun; Wang, Zisheng [China Jiliang University, Magnetism Key Laboratory of Zhejiang Province, Hangzhou (China)

2014-06-15

In order to improve the glass-forming ability (GFA) of Nd-Fe-B ternary alloys to obtain fully amorphous bulk Nd-Fe-B-based alloy, the effects of Mo and Y doping on GFA of the alloys were investigated. It was found that the substitution of Mo for Fe and Y for Nd enhanced the GFA of the Nd-Y-Fe-Mo-B alloys. It was also revealed that the GFA of the samples was optimized by 4 at.% Mo doping and increased with theYcontent. The fully amorphous structures were all formed in the Nd{sub 6-x}Y{sub x}Fe{sub 68}Mo{sub 4}B{sub 22} (x =1-5) alloy rods with 1.5 mm-diameter. After subsequent crystallization, the devitrified Nd{sub 3}Y{sub 3}Fe{sub 68}Mo{sub 4}B{sub 22} alloy rod exhibited a uniform distribution of grains with a coercivity of 364.1 kA/m. The crystallization behavior of Nd{sub 3}Y{sub 3}Fe{sub 68}Mo{sub 4}B{sub 22} BMG was investigated in isothermal situation. The Avrami exponent n determined by JAM plot is lower than 2.5, implying that the crystallization is mainly governed by a growth of particles with decreasing nucleation rate. (orig.)

Estimation of Panel Data Regression Models with Two-Sided Censoring or Truncation

DEFF Research Database (Denmark)

Alan, Sule; Honore, Bo E.; Hu, Luojia

2014-01-01

This paper constructs estimators for panel data regression models with individual speci…fic heterogeneity and two–sided censoring and truncation. Following Powell (1986) the estimation strategy is based on moment conditions constructed from re–censored or re–truncated residuals. While these moment...

Evaluation of oscillator strength in colloidal CdSe/CdS dots-in-rods

Energy Technology Data Exchange (ETDEWEB)

Pisanello, Ferruccio [Universite Pierre et Marie Curie, Laboratoire Kastler Brossel, CNRS UMR8552, Ecole Normale Superieure, 4 place Jussieu, 75005 Paris (France); National Nanotechnology Laboratory of CNR/INFM, Scuola superiore ISUFI, Universita del Salento, 16 Via Arnesano, 73100 Lecce (Italy); Lemenager, Godefroy; Spinicelli, Piernicola; Amo, Alberto; Giacobino, Elisabeth; Bramati, Alberto [Universite Pierre et Marie Curie, Laboratoire Kastler Brossel, CNRS UMR8552, Ecole Normale Superieure, 4 place Jussieu, 75005 Paris (France); Martiradonna, Luigi [Istituto Italiano di Tecnologia (IIT), Center for Bio-Molecular Nanotechnolgy, Via Barsanti 1, Arnesano, 73010 Lecce (Italy); Fiore, Angela [National Nanotechnology Laboratory of CNR/INFM, Scuola superiore ISUFI, Universita del Salento, 16 Via Arnesano, 73100 Lecce (Italy); Cingolani, Roberto; De Vittorio, Massimo [National Nanotechnology Laboratory of CNR/INFM, Scuola superiore ISUFI, Universita del Salento, 16 Via Arnesano, 73100 Lecce (Italy); Istituto Italiano di Tecnologia (IIT), Center for Bio-Molecular Nanotechnolgy, Via Barsanti 1, Arnesano, 73010 Lecce (Italy)

2010-11-15

The oscillator strength in CdSe/CdS colloidal dot-in-rods is evaluated and assessed to be of {proportional_to}1.5. On the basis of this finding, the possibility to reach the strong coupling regime with photonic crystals nanocavities is discussed. In spite that carefully choosing the cavity parameters the strong coupling regime could be analytically achieved at room temperature, theoretical considerations show that the typical Rabi doublet cannot be resolved. The work draws also a viable strategy toward the observation of the strong coupling at cryogenic temperatures. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Failure position detection device for nuclear fuel rod

International Nuclear Information System (INIS)

Ishida, Takeshi; Higuchi, Shin-ichi; Ito, Masaru; Matsuda, Yasuhiko

1987-01-01

Purpose: To easily detect failure position of a nuclear fuel rod by relatively moving an air-tightly shielded detection portion to a fuel rod. Constitution: For detecting the failure position of a leaked fuel assembly, the fuel assembly is dismantled and a portion of withdrawn fuel rod is air-tightly sealed with an inspection portion. The inside of the inspection portion is maintained at a pressure-reduced state. Then, in a case if failed openings are formed at a portion sealed by the inspection portion in the fuel rod, FP gases in the fuel rod are released based on the reduced pressure and the FP gases are detected in the detection portion. Accordingly, by relatively moving the detection portion to the fuel rod, the failure position can be detected. (Yoshino, Y.)

Failure position detection device for nuclear fuel rod

Energy Technology Data Exchange (ETDEWEB)

Ishida, Takeshi; Higuchi, Shin-ichi; Ito, Masaru; Matsuda, Yasuhiko

1987-03-24

Purpose: To easily detect failure position of a nuclear fuel rod by relatively moving an air-tightly shielded detection portion to a fuel rod. Constitution: For detecting the failure position of a leaked fuel assembly, the fuel assembly is dismantled and a portion of withdrawn fuel rod is air-tightly sealed with an inspection portion. The inside of the inspection portion is maintained at a pressure-reduced state. Then, in a case if failed openings are formed at a portion sealed by the inspection portion in the fuel rod, FP gases in the fuel rod are released based on the reduced pressure and the FP gases are detected in the detection portion. Accordingly, by relatively moving the detection portion to the fuel rod, the failure position can be detected. (Yoshino, Y.).

Fuel followed control rod installation at AFRRI

International Nuclear Information System (INIS)

Moore, Mark; Owens, Chris; Forsbacka, Matt

1992-01-01

Fuel Followed Control Rods (FFCRs) were installed at the Armed Forces Radiobiology Research Institute's 1 MW TRIGA Reactor. The procedures for obtaining, shipping, and installing the FFCRs is described. As part of the FFCR installation, the transient rod drive was relocated. Core performance due to the addition of the fuel followed control rods is discussed. (author)

Solitary waves on nonlinear elastic rods. II

DEFF Research Database (Denmark)

Sørensen, Mads Peter; Christiansen, Peter Leth; Lomdahl, P. S.

1987-01-01

In continuation of an earlier study of propagation of solitary waves on nonlinear elastic rods, numerical investigations of blowup, reflection, and fission at continuous and discontinuous variation of the cross section for the rod and reflection at the end of the rod are presented. The results ar...... are compared with predictions of conservation theorems for energy and momentum....

A generalized right truncated bivariate Poisson regression model with applications to health data.

Science.gov (United States)

Islam, M Ataharul; Chowdhury, Rafiqul I

2017-01-01

A generalized right truncated bivariate Poisson regression model is proposed in this paper. Estimation and tests for goodness of fit and over or under dispersion are illustrated for both untruncated and right truncated bivariate Poisson regression models using marginal-conditional approach. Estimation and test procedures are illustrated for bivariate Poisson regression models with applications to Health and Retirement Study data on number of health conditions and the number of health care services utilized. The proposed test statistics are easy to compute and it is evident from the results that the models fit the data very well. A comparison between the right truncated and untruncated bivariate Poisson regression models using the test for nonnested models clearly shows that the truncated model performs significantly better than the untruncated model.

The effect of different screw-rod design on the anti-rotational torque: a biomechanical comparison of three conventional screw-rod constructs.

Science.gov (United States)

Huang, Zifang; Wang, Chongwen; Fan, Hengwei; Sui, Wenyuan; Li, Xueshi; Wang, Qifei; Yang, Junlin

2017-07-28

Screw-rod constructs have been widely used to correct spinal deformities, but the effects of different screw-rod systems on anti-rotational torque have not been determined. This study aimed to analyze the biomechanical effect of different rod-screw constructs on anti-rotational torque. Three conventional spinal screw-rod systems (Legacy, RF-F-10 and USSII) were used to test the anti-rotational torque in the material test machine. ANOVA was performed to evaluate the anti-rotational capacity of different pedicle screws-rod constructs. The anti-rotational torque of Legacy group, RF-F-10 group and USSII group were 12.3 ± 1.9 Nm, 6.8 ± 0.4 Nm, and 3.9 ± 0.8 Nm, with a P value lower than 0.05. This results indicated that the Legacy screws-rod construct could provide a highest anti-rotation capacity, which is 68% and 210% greater than RF-F-10 screw-rod construct and USSII screw-rod respectively. The anti-rotational torque may be mainly affected by screw cap and groove design. Our result showed the anti-rotational torque are: Legacy system > RF-F-10 system > USSII system, suggesting that appropriate rod-screw constructs selection in surgery may be vital for anti-rotational torque improvement and preventing derotation correction loss.

Cutting system for burnable poison rod

International Nuclear Information System (INIS)

Shiina, Atsushi; Toyama, Norihide; Koshino, Yasuo; Fujii, Toshio

1989-01-01

Burnable poison rods attached to spent fuels are contained in a containing box and transported to a receiving pool. The burnable poison rod-containing box is provisionally situated by the operation to a handling device to a provisional setting rack in a cutting pool and attached to a cutting guide of a cutting device upon cutting. The burnable poison rod is cut only in a cutting pool water and tritium generated upon cutting is dissolved into the cutting pool water. Diffusion of tritium is thus restricted. Further, the cutting pool is isolated by a partition device from the receiving pool during cutting of the burnable poison rod. Accordingly, water in which tritium is dissolved is inhibited from moving to the receiving pool and prevail of tritium contamination can be avoided. (T.M.)

Brownian dynamics simulations with stiff finitely extensible nonlinear elastic-Fraenkel springs as approximations to rods in bead-rod models.

Science.gov (United States)

Hsieh, Chih-Chen; Jain, Semant; Larson, Ronald G

2006-01-28

A very stiff finitely extensible nonlinear elastic (FENE)-Fraenkel spring is proposed to replace the rigid rod in the bead-rod model. This allows the adoption of a fast predictor-corrector method so that large time steps can be taken in Brownian dynamics (BD) simulations without over- or understretching the stiff springs. In contrast to the simple bead-rod model, BD simulations with beads and FENE-Fraenkel (FF) springs yield a random-walk configuration at equilibrium. We compare the simulation results of the free-draining bead-FF-spring model with those for the bead-rod model in relaxation, start-up of uniaxial extensional, and simple shear flows, and find that both methods generate nearly identical results. The computational cost per time step for a free-draining BD simulation with the proposed bead-FF-spring model is about twice as high as the traditional bead-rod model with the midpoint algorithm of Liu [J. Chem. Phys. 90, 5826 (1989)]. Nevertheless, computations with the bead-FF-spring model are as efficient as those with the bead-rod model in extensional flow because the former allows larger time steps. Moreover, the Brownian contribution to the stress for the bead-FF-spring model is isotropic and therefore simplifies the calculation of the polymer stresses. In addition, hydrodynamic interaction can more easily be incorporated into the bead-FF-spring model than into the bead-rod model since the metric force arising from the non-Cartesian coordinates used in bead-rod simulations is absent from bead-spring simulations. Finally, with our newly developed bead-FF-spring model, existing computer codes for the bead-spring models can trivially be converted to ones for effective bead-rod simulations merely by replacing the usual FENE or Cohen spring law with a FENE-Fraenkel law, and this convertibility provides a very convenient way to perform multiscale BD simulations.

Analysis of buffering process of control rod hydraulic absorber

International Nuclear Information System (INIS)

Bao Jishi; Qin Benke; Bo Hanliang

2011-01-01

Control Rod Hydraulic Drive Mechanism(CRHDM) is a newly invented build-in control rod drive mechanism. Hydraulic absorber is the key part of this mechanism, and is used to cushion the control rod when the rod scrams. Thus, it prevents the control rod from being deformed and damaged. In this paper dynamics program ANSYS CFX is used to calculate all kinds of flow conditions in hydraulic absorber to obtain its hydraulic characteristics. Based on the flow resistance coefficients obtained from the simulation results, fluid mass and momentum equations were developed to get the trend of pressure change in the hydraulic cylinder and the displacement of the piston rod during the buffering process of the control rod. The results obtained in this paper indicate that the hydraulic absorber meets the design requirement. The work in this paper will be helpful for the design and optimization of the control rod hydraulic absorber. (author)

Control rod experiments in Racine

International Nuclear Information System (INIS)

Stanculescu, A.; Humbert, G.

1981-09-01

A survey of the control-rod experiments planned within the joint CEA/CNEN-DeBeNe critical experiment RACINE is given. The applicability to both heterogeneous and homogeneous large power LMFBR-cores is discussed. Finally, the most significant results of the provisional design calculations performed on behalf of the RACINE control-rod programme are presented

RODMOD: a code for control rod positioning

International Nuclear Information System (INIS)

Vondy, D.R.; Fowler, T.B.

1978-11-01

The report documents a computer code which has been implemented to position control rods according to a prescribed schedule during the calculation of a reactor history. Control rods may be represented explicitly with or without internal black absorber conditions in selected energy groups, or fractional insertion may be done, or both, in a problem. There is provision for control rod follower, movement of materials through a series of zones in a closed loop, and shutdown rod insertion and subsequent removal to allow the reactor history calculation to be continued. This code is incorporated in the system containing the VENTURE diffusion theory neutronics and the BURNER exposure codes for routine use. The implemented automated procedures cause the prescribed control rod insertion schedule to be applied without the access of additional user input data during the calculation of a reactor operating history

Bounded real and positive real balanced truncation using Σ-normalised coprime factors

NARCIS (Netherlands)

Trentelman, H.L.

2009-01-01

In this article, we will extend the method of balanced truncation using normalised right coprime factors of the system transfer matrix to balanced truncation with preservation of half line dissipativity. Special cases are preservation of positive realness and bounded realness. We consider a half

French LMFBR's control rods experience and development

International Nuclear Information System (INIS)

Arnaud, G.; Guigon, A.; Verset, L.

1983-06-01

Since the last ten years, the French program has been, first of all, directed to the setting up, and then the development of, at once, the Phenix control rods, and next, the Super-Phenix ones. The vented pin design, with porous plug and sodium bonding, which allows the choices of large diameters, has been taken, since the Rapsodie experience was decisive. The absorber material is sintered, 10 B enriched, boron carbide. The can is made of 316 type stainless steel, stabilised, or not, with titanium. The experience gained in Phenix up to now is important, and deals with about six loads of control rods. Results confirm the validity of the design of the absorber pins. Some difficulties has been encountered for the guiding devices, due to the swelling of the steel. They have required design and material improvements. Such difficulties are discarded by a new design of the bearing, for the Super-Phenix control rods. The other parts of these rods, from the Primary Shut-Down System, are strictly derived from Phenix. The design of the rods from the Secondary Shut-Down System is rather different, but it's not the case for the design of the absorber pins: in many a way, they are derived from Phenix pins and from Rapsodie control rods. Both types of rods irradiation tests are in progress in Phenix [fr

Advanced gray rod control assembly

Science.gov (United States)

Drudy, Keith J; Carlson, William R; Conner, Michael E; Goldenfield, Mark; Hone, Michael J; Long, Jr., Carroll J; Parkinson, Jerod; Pomirleanu, Radu O

2013-09-17

An advanced gray rod control assembly (GRCA) for a nuclear reactor. The GRCA provides controlled insertion of gray rod assemblies into the reactor, thereby controlling the rate of power produced by the reactor and providing reactivity control at full power. Each gray rod assembly includes an elongated tubular member, a primary neutron-absorber disposed within the tubular member said neutron-absorber comprising an absorber material, preferably tungsten, having a 2200 m/s neutron absorption microscopic capture cross-section of from 10 to 30 barns. An internal support tube can be positioned between the primary absorber and the tubular member as a secondary absorber to enhance neutron absorption, absorber depletion, assembly weight, and assembly heat transfer characteristics.

Refabricated and instrumented fuel rods

International Nuclear Information System (INIS)

Silberstein, K.

2005-01-01

Nuclear Fuel for power reactors capabilities evaluation is strongly based on the intimate knowledge of its behaviour under irradiation. This knowledge can be acquired from refabricated and instrumented fuel rods irradiated at different levels in commercial reactors. This paper presents the development and qualification of a new technique called RECTO related to a double-instrumented rod re-fabrication process developed by CEA/LECA hot laboratory facility at CADARACHE. The technique development includes manufacturing of the properly dimensioned cavity in the fuel pellet stack to house the thermocouple and the use of a newly designed pressure transducer. An analytic irradiation of such a double-instrumented fuel rod will be performed in OSIRIS test reactor starting October 2004. (Author)

Reactor control rod supporting structure

International Nuclear Information System (INIS)

Akimoto, Tokuzo; Miyata, Hiroshi.

1984-01-01

Purpose: To enable stable reactor core control even in extremely great vertical earthquakes, as well as under normal operation conditions in FBR type reactors. Constitution: Since a mechanism for converting the rotational movement of a control rod into vertical movement is placed at the upper portion of the reactor core at high temperature, the mechanism should cause fusion or like other danger after the elapse of a long period of time. In view of the above, the conversion mechanism is disposed to the lower portion of the reactor core at a lower temperature region. Further, the connection between the control rod and the control rod drive can be separated upon great vertical earthquakes. (Seki, T.)

No chiral truncation of quantum log gravity?

Science.gov (United States)

Andrade, Tomás; Marolf, Donald

2010-03-01

At the classical level, chiral gravity may be constructed as a consistent truncation of a larger theory called log gravity by requiring that left-moving charges vanish. In turn, log gravity is the limit of topologically massive gravity (TMG) at a special value of the coupling (the chiral point). We study the situation at the level of linearized quantum fields, focussing on a unitary quantization. While the TMG Hilbert space is continuous at the chiral point, the left-moving Virasoro generators become ill-defined and cannot be used to define a chiral truncation. In a sense, the left-moving asymptotic symmetries are spontaneously broken at the chiral point. In contrast, in a non-unitary quantization of TMG, both the Hilbert space and charges are continuous at the chiral point and define a unitary theory of chiral gravity at the linearized level.

Photonic crystal light collectors in fish retina improve vision in turbid water.

Science.gov (United States)

Kreysing, Moritz; Pusch, Roland; Haverkate, Dorothee; Landsberger, Meik; Engelmann, Jacob; Ruiter, Janina; Mora-Ferrer, Carlos; Ulbricht, Elke; Grosche, Jens; Franze, Kristian; Streif, Stefan; Schumacher, Sarah; Makarov, Felix; Kacza, Johannes; Guck, Jochen; Wolburg, Hartwig; Bowmaker, James K; von der Emde, Gerhard; Schuster, Stefan; Wagner, Hans-Joachim; Reichenbach, Andreas; Francke, Mike

2012-06-29

Despite their diversity, vertebrate retinae are specialized to maximize either photon catch or visual acuity. Here, we describe a functional type that is optimized for neither purpose. In the retina of the elephantnose fish (Gnathonemus petersii), cone photoreceptors are grouped together within reflecting, photonic crystal-lined cups acting as macroreceptors, but rod photoreceptors are positioned behind these reflectors. This unusual arrangement matches rod and cone sensitivity for detecting color-mixed stimuli, whereas the photoreceptor grouping renders the fish insensitive to spatial noise; together, this enables more reliable flight reactions in the fish's dim and turbid habitat as compared with fish lacking this retinal specialization.

Age-related deterioration of rod vision in mice.

Science.gov (United States)

Kolesnikov, Alexander V; Fan, Jie; Crouch, Rosalie K; Kefalov, Vladimir J

2010-08-18

Even in healthy individuals, aging leads to deterioration in visual acuity, contrast sensitivity, visual field, and dark adaptation. Little is known about the neural mechanisms that drive the age-related changes of the retina and, more specifically, photoreceptors. According to one hypothesis, the age-related deterioration in rod function is due to the limited availability of 11-cis-retinal for rod pigment formation. To determine how aging affects rod photoreceptors and to test the retinoid-deficiency hypothesis, we compared the morphological and functional properties of rods of adult and aged B6D2F1/J mice. We found that the number of rods and the length of their outer segments were significantly reduced in 2.5-year-old mice compared with 4-month-old animals. Aging also resulted in a twofold reduction in the total level of opsin in the retina. Behavioral tests revealed that scotopic visual acuity and contrast sensitivity were decreased by twofold in aged mice, and rod ERG recordings demonstrated reduced amplitudes of both a- and b-waves. Sensitivity of aged rods determined from single-cell recordings was also decreased by 1.5-fold, corresponding to not more than 1% free opsin in these photoreceptors, and kinetic parameters of dim flash response were not altered. Notably, the rate of rod dark adaptation was unaffected by age. Thus, our results argue against age-related deficiency of 11-cis-retinal in the B6D2F1/J mouse rod visual cycle. Surprisingly, the level of cellular dark noise was increased in aged rods, providing an alternative mechanism for their desensitization.

Optimized Control Rods of the BR2 Reactor

Energy Technology Data Exchange (ETDEWEB)

Kalcheva, Silva; Koonen, E.

2007-09-15

At the present time the BR-2 reactor uses control elements with cadmium as neutron absorbing part. The lower section of the control element is a beryllium assembly cooled by light water. Due to the burn up of the lower end of the cadmium section during the reactor operation, the presently used rods for reactivity control of the BR-2 reactor have to be replaced by new ones. Considered are various types Control Rods with full active part of the following materials: cadmium (Cd), hafnium (Hf), europium oxide (Eu2O3) and gadolinium (Gd2O3). Options to decrease the burn up of the control rod material in the hot spot, such as use of stainless steel in the lower active part of the Control Rod are discussed. Comparison with the characteristics of the presently used Control Rods types is performed. The changing of the characteristics of different types Control Rods and the perturbation effects on the reactor neutronics during the BR-2 fuel cycle are investigated. The burn up of the Control Rod absorbing material, total and differential control rods worth, macroscopic and effective microscopic absorption cross sections, fuel and reactivity evolution are evaluated during approximately 30 operating cycles.

Control rod repositioning considerations in core design analysis

International Nuclear Information System (INIS)

Armstrong, B.C.; Buechel, R.J.

1990-01-01

Control rod repositioning is a method for minimizing rod cluster control assembly (RCCA) wear in the upper internals area where the guide cards interface with the rodlets of the RCCAs. A number of utilities have implemented strategies for rod repositioning, which often has no impact on the nuclear analysis for cases where the control rods are never repositioned into the active fuel. Other strategies involve repositioning the control rods several steps into the active fuel. The impact of this type of repositioning on the axial power shape and consequently the total peaking factor F Q T varies, depending on the method in which the repositioning is implemented at the plant. Operating for long periods with all the control and shutdown rods inserted several steps in the active fuel followed by withdrawing them fully from the core results in a shifting of the power distribution toward the top of the core and must be accounted for in the design analysis. On the other hand, an optional plan for control rod repositioning that considers margins available in related design parameters can be devised that minimizes the effects of the repositioning for the reload. This paper summarizes a rod repositioning strategy implemented for a recent reload and some calculated power shape results for this strategy and other scenarios

Optimized Control Rods of the BR2 Reactor

International Nuclear Information System (INIS)

Kalcheva, Silva; Koonen, E.

2007-01-01

At the present time the BR-2 reactor uses control elements with cadmium as neutron absorbing part. The lower section of the control element is a beryllium assembly cooled by light water. Due to the burn up of the lower end of the cadmium section during the reactor operation, the presently used rods for reactivity control of the BR-2 reactor have to be replaced by new ones. Considered are various types Control Rods with full active part of the following materials: cadmium (Cd), hafnium (Hf), europium oxide (Eu2O3) and gadolinium (Gd2O3). Options to decrease the burn up of the control rod material in the hot spot, such as use of stainless steel in the lower active part of the Control Rod are discussed. Comparison with the characteristics of the presently used Control Rods types is performed. The changing of the characteristics of different types Control Rods and the perturbation effects on the reactor neutronics during the BR-2 fuel cycle are investigated. The burn up of the Control Rod absorbing material, total and differential control rods worth, macroscopic and effective microscopic absorption cross sections, fuel and reactivity evolution are evaluated during approximately 30 operating cycles.

Conceptual design report of the SMART fuel rod

Energy Technology Data Exchange (ETDEWEB)

Kim, Dae Ho; Lee, Chan Bock; Bang, Je Gun; Jung, Yeon Ho [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-03-01

The SMART fuel rod is based on 17 x 17 KOFA(Korea Fuel Assembly) fuel rod of the 950MWe pressurize water reactor. The fuel stack length of the KOFA is 3658mm, otherwise SMART fuel rod stack length is 2000mm. The fuel rod contains UO{sub 2} pellets with the enrichment of 4.95%. All the fuel in core will be replaced every 35 months. The average LHGR of the fuel rod is 120 W/cm, commercial PWR is 178 W/cm, SMART LHGR is lower about 31% than commercial PWR. The core inlet and outlet temperature of coolant are respectively 270 deg C and 310 deg C, commercial PWR are respectively 291.6 deg C and 326.8 deg C, SMART inlet and outlet temperature is lower averaged 19.2 deg C than commercial PWR. The coolant use mixed soluble ammonia in high purity water and boron is not in. The general performance of the fuel rod UO{sub 2} pellet has been already verified through the sufficient burnup (60,000 MWd/MTU-rod avg.) experience as the rods of same design in commercial PWR's. But cladding corrosion is required the further verification. (author). 13 refs., 3 figs., 8 tabs.

Controlled synthesis of thorium and uranium oxide nano-crystals

International Nuclear Information System (INIS)

Hudry, Damien; Apostolidis, Christos; Walter, Olaf; Gouder, Thomas; Courtois, Eglantine; Kubel, Christian; Meyer, Daniel

2013-01-01

Very little is known about the size and shape effects on the properties of actinide compounds. As a consequence, the controlled synthesis of well-defined actinide-based nano-crystals constitutes a fundamental step before studying their corresponding properties. In this paper, we report on the non-aqueous surfactant-assisted synthesis of thorium and uranium oxide nano-crystals. The final characteristics of thorium and uranium oxide nano-crystals can be easily tuned by controlling a few experimental parameters such as the nature of the actinide precursor and the composition of the organic system (e.g., the chemical nature of the surfactants and their relative concentrations). Additionally, the influence of these parameters on the outcome of the synthesis is highly dependent on the nature of the actinide element (thorium versus uranium). By using optimised experimental conditions, monodisperse isotropic uranium oxide nano-crystals with different sizes (4.5 and 10.7 nm) as well as branched nano-crystals (overall size ca. 5 nm), nano-dots (ca. 4 nm) and nano-rods (with ultra-small diameters of 1 nm) of thorium oxide were synthesised. (authors)

Scattering of x-ray from crystal surfaces

International Nuclear Information System (INIS)

Andrews, S.R.; Cowley, R.A.

1985-01-01

X-ray measurements performed on a variety of materials demonstrate that it is possible to observe diffuse scattering that originates in the abrupt change of density at a crystal surface. Such a discontinuity gives rise, in general, to rods of scattering in reciprocal space which are most intense close to the Bragg peaks tau and are well defined for sufficiently smooth surfaces. For wave-vector transfer Q=tau+q the q-dependence of the intensity of scattering gives information on the topographic structure of the crystal surface. Experimental results on crystals of GaAs and KTaO 3 , with surfaces prepared in various ways, were obtained using conventional x-ray techniques with a rotating anode source and can be described by a continuum model of the surface. There are discrepancies between the predictions of the models and the experimental results and the suggest that further experiments are needed to achieve a more complete understanding. (author)

Reduction of variable-truncation artifacts from beam occlusion during in situ x-ray tomography

Science.gov (United States)

Borg, Leise; Jørgensen, Jakob S.; Frikel, Jürgen; Sporring, Jon

2017-12-01

Many in situ x-ray tomography studies require experimental rigs which may partially occlude the beam and cause parts of the projection data to be missing. In a study of fluid flow in porous chalk using a percolation cell with four metal bars drastic streak artifacts arise in the filtered backprojection (FBP) reconstruction at certain orientations. Projections with non-trivial variable truncation caused by the metal bars are the source of these variable-truncation artifacts. To understand the artifacts a mathematical model of variable-truncation data as a function of metal bar radius and distance to sample is derived and verified numerically and with experimental data. The model accurately describes the arising variable-truncation artifacts across simulated variations of the experimental setup. Three variable-truncation artifact-reduction methods are proposed, all aimed at addressing sinogram discontinuities that are shown to be the source of the streaks. The ‘reduction to limited angle’ (RLA) method simply keeps only non-truncated projections; the ‘detector-directed smoothing’ (DDS) method smooths the discontinuities; while the ‘reflexive boundary condition’ (RBC) method enforces a zero derivative at the discontinuities. Experimental results using both simulated and real data show that the proposed methods effectively reduce variable-truncation artifacts. The RBC method is found to provide the best artifact reduction and preservation of image features using both visual and quantitative assessment. The analysis and artifact-reduction methods are designed in context of FBP reconstruction motivated by computational efficiency practical for large, real synchrotron data. While a specific variable-truncation case is considered, the proposed methods can be applied to general data cut-offs arising in different in situ x-ray tomography experiments.

Results from In-pile experiments on LWR fuel rod behavior under LOCA conditions with unirradiated rods

International Nuclear Information System (INIS)

Sepold, L.; Karb, E.H.; Pruessmann, M.

1981-06-01

This report summarizes the results of the FR2-in-pile tests at KfK (Kernforschungszentrum Karlsruhe) with unirradiated test rods. The in-pile tests with the objective of investigating the influence of a nuclear environment on the mechanisms of fuel rod failure were being performed with irradiated and unirradiated single rods of a PWR design in the DK loop of the FR2 reactor. The main parameter of the test program was the burnup, ranging from 2.500 to 35.000 MWd/t. The program with unirradiated specimens comprised the series A and B with a total of 14 tests. (orig.) [de

Amplitude reconstruction from complete photoproduction experiments and truncated partial-wave expansions

International Nuclear Information System (INIS)

Workman, R. L.; Tiator, L.; Wunderlich, Y.; Doring, M.; Haberzettl, H.

2017-01-01

Here, we compare the methods of amplitude reconstruction, for a complete experiment and a truncated partial-wave analysis, applied to the photoproduction of pseudoscalar mesons. The approach is pedagogical, showing in detail how the amplitude reconstruction (observables measured at a single energy and angle) is related to a truncated partial-wave analysis (observables measured at a single energy and a number of angles).

Air-water two-phase flow in a four by four rod bundle with partial length rods

International Nuclear Information System (INIS)

Ohta, Motoki; Kamei, Akihiro; Mizutani, Yoshitaka; Hosokawa, Shigeo; Tomiyama, Akio

2009-01-01

Partial length rods (PLR) are used in fuel bundles of BWR to reduce pressure drops in two-phase regions and to optimize the power distribution. Since little is known about effects of PLR on two-phase flows, air-water two-phase flow around PLRs in a four by four rod bundle is visualized by using a high-speed video camera. The experimental apparatus consists of acrylic channel box and transparent rods. Air and water at atmospheric pressure and room temperature are used for the gas and liquid phases, respectively. The ranges of the gas and liquid volume fluxes, J G and J L , are 0.4 L G L , the flow pattern in the downstream of PLR transits to slug flow, and the flow patterns in the surrounding subchannels transit to bubbly flow due to the redistribution of gas flow. (2) In annular flow, the liquid film on the PLR forms a liquid column above the end cap of PLR. Droplets are generated by column breakup and deposit on liquid films on the neighboring rods. (3) The liquid film thickness on the surface of neighbor rods facing the PLR increases and it reduces that on their opposite surface in the downstream of PLR. (author)

Development of design technology on thermal-hydraulic performance in tight-lattice rod bundle. III - Numerical estimation on rod bowing effect based on X-ray CT data

International Nuclear Information System (INIS)

Misawa, Takeharu; Ohnuki, Akira; Katsuyama, Kozo; Nagamine, Tsuyoshi; Nakamura, Yasuo; Akimoto, Hajime; Mitsutake, Toru; Misawa, Susumu

2007-01-01

Design studies of the Innovative Water Reactor for Flexible Fuel Cycle (FLWR) are being carried out at the Japan Atomic Energy Agency (JAEA) as one candidate for the future reactors. In actual core design, it is precondition to prevent fuel rods contact due to fuel rod bowing. However, the FLWR cores have nonconventional characteristics such as a hexagonal tight lattice arrangement and a high enrichment fuel loading. Therefore, as conservative evaluation, it is important to investigate influence of fuel rod bowing upon the boiling transition. In the JAEA, a 37-rod bundle experiments (base case test section (1.3mm gap width), gap width effect test section (1.0mm gap width), and rod bowing test section) were performed in order to investigate the thermal hydraulic characteristics in the tight lattice bundle. In this paper, the rod bowing effect test is paid attention. It is suspected that the actual fuel rod positions in the rod bowing test section may be different from the design-based positions. Even a slight displacement from the design-based position of fuel rod may occur variation of flow area, and give influence upon the thermal hydraulic characteristics in the rod bundle. Therefore, if the critical power in the rod bundle is evaluated by an analytical approach, the analysis based on more correct input can be performed by using actual fuel rod position data. In this study, the rod positions in the rod bowing test section were measured using the high energy X-ray computer tomography (Xray-CT). Based on the measured rod positions data, the subchannel analysis by the NASCA code was performed, in order to investigate applicability of the NASCA code to BT estimation of the rod bowing test section, and influence of displacement from design-based rod position upon BT estimation by the NASCA code. The predicted critical powers are agreement with those obtained by the experiment. The analysis based on the design-based rod positions is also performed, and the result is

Self-collimation-based photonic crystal notch filters

International Nuclear Information System (INIS)

Lee, Sun-Goo; Kim, Seong-Han; Kee, Chul-Sik; Kim, Kap-Joong

2017-01-01

We introduce a design concept of an optical notch filter (NF) utilizing two perfectly reflecting mirrors and a beam splitter. Based on the new design concept, a photonic crystal (PC)-NF based on the self-collimation phenomenon in a two-dimensional PC is proposed and studied through finite-difference time-domain simulations and experimental measurements in a microwave region. The transmission properties of the self-collimation-based PC-NF were demonstrated to be controlled by adjusting the values of parameters such as the radius of rods in the line-defect beam splitter, distance between the two perfectly reflecting mirrors, and radius of rods on the outermost surface of the perfectly reflecting mirrors. Our results indicate that the proposed design concept could provide a new approach to manipulate light propagation, and the PC-NF could increase the applicability of the self-collimation phenomenon in a PC. (paper)

Management of radioactive disused lightning rods

Energy Technology Data Exchange (ETDEWEB)

Santos, Paulo de Oliveira; Silva, Fabio, E-mail: pos@cdtn.br, E-mail: silvaf@cdtn.br [Centro de Desenvolvimento da Energia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2013-07-01

The manufacture of radioactive lightning rod was allowed from 1970 to 1989. This authorization was based on state-of-the art science of that time that verified that radioactive lightning rods had efficiency superior to the conventional lightning rods, denominated Franklin. However, the experience showed that their efficiency was not superior enough to justify the use of radioactive sources. Consequently, in 1989, the National Commission or Nuclear Energy - CNEN, issued the Resolution 04/89 from 04-19-1989, that forbidden the importation of {sup 241}Am tapes, assembling and commercialization of radioactive lightning-rods. The institutes of CNEN are responsible for receiving these lightning-rods and sending to the users procedures for removing and dispatch to the institutes. Therewith, these devices are kept away from the human being and environment. The Nuclear technology Development Center - CDTN and Institute for Energy and Nuclear Research - IPEN of CNEN, has built laboratories appropriate for dismantling such devices and store the {sup 241}Am tapes safely. Nowadays are being researched methodologies to evaluate the contamination levels of the frame for possible recycling and become better the management of these devices. (author)

Management of radioactive disused lightning rods

International Nuclear Information System (INIS)

Santos, Paulo de Oliveira; Silva, Fabio

2013-01-01

The manufacture of radioactive lightning rod was allowed from 1970 to 1989. This authorization was based on state-of-the art science of that time that verified that radioactive lightning rods had efficiency superior to the conventional lightning rods, denominated Franklin. However, the experience showed that their efficiency was not superior enough to justify the use of radioactive sources. Consequently, in 1989, the National Commission or Nuclear Energy - CNEN, issued the Resolution 04/89 from 04-19-1989, that forbidden the importation of 241 Am tapes, assembling and commercialization of radioactive lightning-rods. The institutes of CNEN are responsible for receiving these lightning-rods and sending to the users procedures for removing and dispatch to the institutes. Therewith, these devices are kept away from the human being and environment. The Nuclear technology Development Center - CDTN and Institute for Energy and Nuclear Research - IPEN of CNEN, has built laboratories appropriate for dismantling such devices and store the 241 Am tapes safely. Nowadays are being researched methodologies to evaluate the contamination levels of the frame for possible recycling and become better the management of these devices. (author)

Stabilizing device for control rod tip

International Nuclear Information System (INIS)

Verdone, G.F.

1982-01-01

A control rod has a spring device on its lower end for eliminating oscillatory contact of the rod against its adjacent guide tube wall. The base of the device is connected to the lower tip of the rod. A plurality of elongated extensions are cantilevered downward from the base. Each extension has a shoulder for contacting the guide tube, and the plurality of shoulders as a group has a transverse dimension that is preset to be larger than the inner diameter of the guide tube such that an interference fit is obtained when the control rod is inserted in the tube. The elongated extensions form an open-ended, substantially hollow member through which most of the liquid coolant flows, and the spaces between adjacent extensions allow the flow to bypass the shoulders without experiencing a significant pressure drop

Detection device for control rod scram

International Nuclear Information System (INIS)

Ishiyama, Satoshi.

1989-01-01

The device of the present invention comprises a control rod dropping separately from a control rod driving mechanism main body, a following tube falling separately accompanying therewith and a guide tube for guiding the dropping of the control rod and the following tube. Further, rare earth permanent magnets are embedded with the pole being axially oriented in the following tube and bobbins each mounted with an inner flange made of high magnetic permeability material are disposed to the guide tube. Coils are wound in the bobbin. In this control rod scram detection device, since magnetic fluxes can effectively be supplied to the coils, it is possible to obtain stable and highly reliable scram detection signals. Further, since the coils and the bobbins can be manufactured separately from the guide tube, their assemblies can be tested independently from the guide tube. (K.M.)

Modified Truncated Multiplicity Analysis to Improve Verification of Uranium Fuel Cycle Materials

International Nuclear Information System (INIS)

LaFleur, A.; Miller, K.; Swinhoe, M.; Belian, A.; Croft, S.

2015-01-01

Accurate verification of 235U enrichment and mass in UF6 storage cylinders and the UO2F2 holdup contained in the process equipment is needed to improve international safeguards and nuclear material accountancy at uranium enrichment plants. Small UF6 cylinders (1.5'' and 5'' diameter) are used to store the full range of enrichments from depleted to highly-enriched UF6. For independent verification of these materials, it is essential that the 235U mass and enrichment measurements do not rely on facility operator declarations. Furthermore, in order to be deployed by IAEA inspectors to detect undeclared activities (e.g., during complementary access), it is also imperative that the measurement technique is quick, portable, and sensitive to a broad range of 235U masses. Truncated multiplicity analysis is a technique that reduces the variance in the measured count rates by only considering moments 1, 2, and 3 of the multiplicity distribution. This is especially important for reducing the uncertainty in the measured doubles and triples rates in environments with a high cosmic ray background relative to the uranium signal strength. However, we believe that the existing truncated multiplicity analysis throws away too much useful data by truncating the distribution after the third moment. This paper describes a modified truncated multiplicity analysis method that determines the optimal moment to truncate the multiplicity distribution based on the measured data. Experimental measurements of small UF6 cylinders and UO2F2 working reference materials were performed at Los Alamos National Laboratory (LANL). The data were analyzed using traditional and modified truncated multiplicity analysis to determine the optimal moment to truncate the multiplicity distribution to minimize the uncertainty in the measured count rates. The results from this analysis directly support nuclear safeguards at enrichment plants and provide a more accurate verification method for UF6

Analysis of control rod behavior based on numerical simulation

International Nuclear Information System (INIS)

Ha, D. G.; Park, J. K.; Park, N. G.; Suh, J. M.; Jeon, K. L.

2010-01-01

The main function of a control rod is to control core reactivity change during operation associated with changes in power, coolant temperature, and dissolved boron concentration by the insertion and withdrawal of control rods from the fuel assemblies. In a scram, the control rod assemblies are released from the CRDMs (Control Rod Drive Mechanisms) and, due to gravity, drop rapidly into the fuel assemblies. The control rod insertion time during a scram must be within the time limits established by the overall core safety analysis. To assure the control rod operational functions, the guide thimbles shall not obstruct the insertion and withdrawal of the control rods or cause any damage to the fuel assembly. When fuel assembly bow occurs, it can affect both the operating performance and the core safety. In this study, the drag forces of the control rod are estimated by a numerical simulation to evaluate the guide tube bow effect on control rod withdrawal. The contact condition effects are also considered. A full scale 3D model is developed for the evaluation, and ANSYS - commercial numerical analysis code - is used for this numerical simulation. (authors)

Modeling the Effect of APC Truncation on Destruction Complex Function in Colorectal Cancer Cells

Science.gov (United States)

Barua, Dipak; Hlavacek, William S.

2013-01-01

In colorectal cancer cells, APC, a tumor suppressor protein, is commonly expressed in truncated form. Truncation of APC is believed to disrupt degradation of β—catenin, which is regulated by a multiprotein complex called the destruction complex. The destruction complex comprises APC, Axin, β—catenin, serine/threonine kinases, and other proteins. The kinases and , which are recruited by Axin, mediate phosphorylation of β—catenin, which initiates its ubiquitination and proteosomal degradation. The mechanism of regulation of β—catenin degradation by the destruction complex and the role of truncation of APC in colorectal cancer are not entirely understood. Through formulation and analysis of a rule-based computational model, we investigated the regulation of β—catenin phosphorylation and degradation by APC and the effect of APC truncation on function of the destruction complex. The model integrates available mechanistic knowledge about site-specific interactions and phosphorylation of destruction complex components and is consistent with an array of published data. We find that the phosphorylated truncated form of APC can outcompete Axin for binding to β—catenin, provided that Axin is limiting, and thereby sequester β—catenin away from Axin and the Axin-recruited kinases and . Full-length APC also competes with Axin for binding to β—catenin; however, full-length APC is able, through its SAMP repeats, which bind Axin and which are missing in truncated oncogenic forms of APC, to bring β—catenin into indirect association with Axin and Axin-recruited kinases. Because our model indicates that the positive effects of truncated APC on β—catenin levels depend on phosphorylation of APC, at the first 20-amino acid repeat, and because phosphorylation of this site is mediated by , we suggest that is a potential target for therapeutic intervention in colorectal cancer. Specific inhibition of is predicted to limit binding of β—catenin to truncated

The role of lipids and salts in two-dimensional crystallization of the glycine-betaine transporter BetP from Corynebacterium glutamicum

DEFF Research Database (Denmark)

Tsai, Ching-Ju; Ejsing, Christer S.; Shevchenko, Andrej

2007-01-01

The osmoregulated and chill-sensitive glycine-betaine transporter (BetP) from Corynebacterium glutamicum was reconstituted into lipids to form two-dimensional (2D) crystals. The sensitivity of BetP partly bases on its interaction with lipids. Here we demonstrate that lipids and salts influence...... crystal morphology and crystallinity of a C-terminally truncated BetP. The salt type and concentration during crystallization determined whether crystals grew in the form of planar-tubes, sheets or vesicles, while the lipid type influenced crystal packing and order. Three different lipid preparations...... for 2D crystallization were compared. Only the use of lipids extracted from C. glutamicum cells led to the formation of large, well-ordered crystalline areas. To understand the lipid-derived influence on crystallinity, lipid extracts from different stages of the crystallization process were analyzed...

Nuclear fuel rod end plug weld inspection

International Nuclear Information System (INIS)

Parker, M. A.; Patrick, S. S.; Rice, G. F.

1985-01-01

Apparatus and method for testing TIG (tungsten inert gas) welds of end plugs on a sealed nuclear reactor fuel rod. An X-ray fluorescent spectrograph testing unit detects tungsten inclusion weld defects in the top end plug's seal weld. Separate ultrasonic weld inspection system testing units test the top end plug's seal and girth welds and test the bottom end plug's girth weld for penetration, porosity and wall thinning defects. The nuclear fuel rod is automatically moved into and out from each testing unit and is automatically transported between the testing units by rod handling devices. A controller supervises the operation of the testing units and the rod handling devices

Transition between metamaterial and photonic-crystal behavior in arrays of dielectric rods

Czech Academy of Sciences Publication Activity Database

Dominec, Filip; Kadlec, Christelle; Němec, Hynek; Kužel, Petr; Kadlec, Filip

2014-01-01

Roč. 22, č. 25 (2014), s. 30492-30503 ISSN 1094-4087 R&D Projects: GA ČR(CZ) GA14-25639S Institutional support: RVO:68378271 Keywords : metamaterials * photonic crystals * negative refractive index * dielectrics Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.488, year: 2014

Control rod control device

International Nuclear Information System (INIS)

Seiji, Takehiko; Obara, Kohei; Yanagihashi, Kazumi

1998-01-01

The present invention provides a device suitable for switching of electric motors for driving each of control rods in a nuclear reactor. Namely, in a control rod controlling device, a plurality of previously allotted electric motors connected in parallel as groups, and electric motors of any selected group are driven. In this case, a voltage of not driving predetermined selected electric motors is at first applied. In this state an electric current supplied to the circuit of predetermined electric motors is detected. Whether integration or failure of a power source and the circuit of the predetermined electric motors are normal or not is judged by the detected electric current supplied. After they are judged normal, the electric motors are driven by a regular voltage. With such procedures, whether the selected circuit is normal or not can be accurately confirmed previously. Since the electric motors are not driven just at the selected time, the control rods are not operated erroneously. (I.S.)

A Lynden-Bell integral estimator for the tail index of right-truncated ...

African Journals Online (AJOL)

By means of a Lynden-Bell integral with deterministic threshold, Worms and Worms [A Lynden-Bell integral estimator for extremes of randomly truncated data. Statist. Probab. Lett. 2016; 109: 106-117] recently introduced an asymptotically normal estimator of the tail index for randomly right-truncated Pareto-type data.

Correlation of NTD-silicon rod and slice resistivity

International Nuclear Information System (INIS)

Wolverton, W.M.

1984-01-01

Neutron transmutation doped silicon is an electronic material which presents an opportunity to explore a high level of resistivity characterization. This is due to its excellent uniformity of dopant concentration. Appropriate resistivity measurements on the ingot raw material can be used as a predictor of slice resistivity. Correlation of finished NTD rod (i.e. ingot) resistivity to as-cut slice resistivity (after the sawing process) is addressed in the scope of this paper. Empirical data show that the shift of slice-center resistivity compared to rod-end center resistivity is a function of a new kind of rod radial-resistivity gradient. This function has two domains, and most rods are in domain ''A''. Correlating equations show how to significantly improve the prediction of slice resistivity of rods in domain ''A''. The new rod resistivity specifications have resulted in manufacturing economies in the production of NTD silicon slices

Truncated States Obtained by Iteration

International Nuclear Information System (INIS)

Cardoso, W. B.; Almeida, N. G. de

2008-01-01

We introduce the concept of truncated states obtained via iterative processes (TSI) and study its statistical features, making an analogy with dynamical systems theory (DST). As a specific example, we have studied TSI for the doubling and the logistic functions, which are standard functions in studying chaos. TSI for both the doubling and logistic functions exhibit certain similar patterns when their statistical features are compared from the point of view of DST

The Dynamics of Truncated Black Hole Accretion Disks. I. Viscous Hydrodynamic Case

Energy Technology Data Exchange (ETDEWEB)

Hogg, J. Drew; Reynolds, Christopher S. [Department of Astronomy, University of Maryland, College Park, MD 20742 (United States)

2017-07-10

Truncated accretion disks are commonly invoked to explain the spectro-temporal variability in accreting black holes in both small systems, i.e., state transitions in galactic black hole binaries (GBHBs), and large systems, i.e., low-luminosity active galactic nuclei (LLAGNs). In the canonical truncated disk model of moderately low accretion rate systems, gas in the inner region of the accretion disk occupies a hot, radiatively inefficient phase, which leads to a geometrically thick disk, while the gas in the outer region occupies a cooler, radiatively efficient phase that resides in the standard geometrically thin disk. Observationally, there is strong empirical evidence to support this phenomenological model, but a detailed understanding of the dynamics of truncated disks is lacking. We present a well-resolved viscous, hydrodynamic simulation that uses an ad hoc cooling prescription to drive a thermal instability and, hence, produce the first sustained truncated accretion disk. With this simulation, we perform a study of the dynamics, angular momentum transport, and energetics of a truncated disk. We find that the time variability introduced by the quasi-periodic transition of gas from efficient cooling to inefficient cooling impacts the evolution of the simulated disk. A consequence of the thermal instability is that an outflow is launched from the hot/cold gas interface, which drives large, sub-Keplerian convective cells into the disk atmosphere. The convective cells introduce a viscous θ − ϕ stress that is less than the generic r − ϕ viscous stress component, but greatly influences the evolution of the disk. In the truncated disk, we find that the bulk of the accreted gas is in the hot phase.

A Multistep Extending Truncation Method towards Model Construction of Infinite-State Markov Chains

Directory of Open Access Journals (Sweden)

Kemin Wang

2014-01-01

Full Text Available The model checking of Infinite-State Continuous Time Markov Chains will inevitably encounter the state explosion problem when constructing the CTMCs model; our method is to get a truncated model of the infinite one; to get a sufficient truncated model to meet the model checking of Continuous Stochastic Logic based system properties, we propose a multistep extending advanced truncation method towards model construction of CTMCs and implement it in the INFAMY model checker; the experiment results show that our method is effective.

Lifting device for drilling rods

Energy Technology Data Exchange (ETDEWEB)

Radzivilovich, L L; Laptev, A G; Lipkovich, V A

1982-01-01

A lifter is proposed for drilling rods including a spacer stand with rotating bracket, boom with by-pass rollers, spacing and lifting hydrocylinders with rods and flexible tie mechanism. In order to improve labor productivity by improving maneuverability and to increase the maintenance zone, the lifter is equipped with a hydrocylinder of advance and a cross piece which is installed with the possibility of forward and rotational movement on the stand, and in which by means of the hydrocylinder of advance a boom is attached. Within the indicated boom there is a branch of the flexible tie mechanism with end attached with the possibility of regulation over the length on a rotating bracket, while the rod of the lifting hydrocylinder is connected to the cross piece.

Rodding Surgery

Science.gov (United States)

... Physical activity prior to surgery,  Length of the operation; anesthesia issues,  Reason for the choice of rod,  Time in the hospital,  Length of recovery time at home,  Pain management including control of muscle spasms,  The rehabilitation plan. ...

Convergence problems of Coulomb and multipole sums in crystals

International Nuclear Information System (INIS)

Kholopov, Evgenii V

2004-01-01

Different ways of calculating Coulomb and dipole sums over crystal lattices are analyzed comparatively. It is shown that the currently alleged disagreement between various approaches originates in ignoring the requirement for the self-consistency of surface conditions, which are of fundamental importance due to the long-range nature of the bulk interactions that these sums describe. This is especially true of surfaces arising when direct sums for infinite translation-invariant structures are truncated. The charge conditions for actual surfaces being self-consistently adjusted to the bulk state are formally the same as those on the truncation surface, consistent with the concept of the thermodynamic limit for the bulk-state absolute equilibrium and with the fact that the surface energy contribution in this case is, naturally, statistically small compared to the bulk contribution. Two-point multipole expansions are briefly discussed, and the problems associated with the boundary of their convergence circle are pointed out. (reviews of topical problems)

Family Therapy for the "Truncated" Nuclear Family.

Science.gov (United States)

Zuk, Gerald H.

1980-01-01

The truncated nuclear family consists of a two-generation group in which conflict has produced a polarization of values. The single-parent family is at special risk. Go-between process enables the therapist to depolarize sharply conflicted values and reduce pathogenic relating. (Author)

BWR control rod drive scram pilot valve monitoring system

International Nuclear Information System (INIS)

Soden, R.A.; Kelly, V.

1984-01-01

The control rod drive system in a Boiling Water Reactor is the most important safety system in the power plant. All components of the system can be verified except the solenoid operated, scram pilot valves without scramming a rod. The pilot valve mechancial works is the weak link to the control rod drive system. These pilot valves control the hydraulic system which applies pressure to the ''insert'' side of the control rod piston and vents the ''withdraw'' side of the piston causing the rods to insert during a scam. The only verification that the valve is operating properly is to scram the rod. The concern for this portion of the system is demonstrated by the high number of redundant components and complete periodic testing of the electrical circuits. The pilot valve can become hung-up through wear, fracture of internal components, mechanical binding, foreign material or chemicals left in the valve during maintenance, etc. If the valve becomes hung-up the electrical tests performed will not indicate this condition and scramming the rod is in jeopardy. Only an attempt to scram a rod will indicate the hung-up valve. While this condition exists the rod is considered inoperative. This paper describes a system developed at a nuclear power plant that monitors the pilot valves on the control rod drive system. This system utilizes pattern recognition to assure proper internal workings of the scram pilot valves to plant operators. The system is totally automatic such that each time the valve is operated on a ''half scram'', a printout is available to the operator along with light indication that each of the 370 valves (on one unit of a BWR) is operating properly. With this monitoring system installed, all components of the control rod drive system including the solenoid pilot valves can be verified as operational without scramming any rods

BWR control rod drive scram pilot valve monitoring program

International Nuclear Information System (INIS)

Soden, R.A.; Kelly, V.

1986-01-01

The control rod drive system in a Boiling Water Reactor is the most important safety system in the power plant. All components of the system can be verified except the solenoid operated, scram pilot valves without scramming a rod. The pilot valve mechanical works is the weak link to the control rod drive system. These pilot valves control the hydraulic system which applies pressure to the insert side of the control rod piston and vents the withdraw side of the piston causing the rods to insert during a scram. The only verification that the valve is operating properly is to scram the rod. The concern for this portion of the system is demonstrated by the high number of redundant components and complete periodic testing of the electrical circuits. The pilot valve can become hung-up through wear, fracture of internal components, mechanical binding, foreign material or chemicals left in the valve during maintenance, etc. If the valve becomes hung-up the electrical tests performed will not indicate this condition and scramming the rod is in jeopardy. Only an attempt to scram a rod will indicate the hung-up valve. While this condition exists the rod is considered inoperative. This paper describes a system developed at a nuclear power plant that monitors the pilot valves on the control rod drive system. This system utilizes pattern recognition to assure proper internal workings of the scram pilot valves to plant operators. The system is totally automatic such that each time the valve is operated on a half scram, a printout is available to the operator along with light indication that each of the 370 valves (on one unit of a BWR) is operating properly. With this monitoring system installed, all components of the control rod drive system including the solenoid pilot valves can be verified as operational without scramming any rods

International symposium on fuel rod simulators: development and application

Energy Technology Data Exchange (ETDEWEB)

McCulloch, R.W. (comp.)

1981-05-01

Separate abstracts are included for each of the papers presented concerning fuel rod simulator operation and performance; simulator design and evaluation; clad heated fuel rod simulators and fuel rod simulators for cladding investigations; fuel rod simulator components and inspection; and simulator analytical modeling. Ten papers have previously been input to the Energy Data Base.

Apparatus for inspecting a irradiated nuclear fuel rod

International Nuclear Information System (INIS)

Saura, Hideaki; Yonemura, Eizo.

1975-01-01

Object: To increase safety and inspection efficiency by operating irradiated fuel rods, which are accommodated in a water-filled pool after being taken out from the reactor. Structure: When making inspection of irradiated fuel rods, particularly the cladding tube thereof, a fuel box which stores irradiated fuel rods in a water pool is secured to a securement mechanism with slime removal apparatus and inspection apparatus on either side capable of being vertically moved, and it is then stopped at a water depth of about 2 meters. When the lid of the box is opened, irradiated fuel rods are taken out with gripping means and then secured together with the gripping means to an operation base provided on the outside of the pool. Thereafter, the box is lowered by operating pedals on the operation base to completely pull out the irradiated fuel rods from the box, and the irradiated fuel rods are then horizontally moved and then held in a suspended state. Next a slime removal apparatus in raised by operating pedals and an inspection element assembly are progressively raised for inspection of the state of the cladding tube of each fuel rod after removal of slime therefrom. (Nakamura, S.)

Slip-spring model of entangled rod-coil block copolymers

Science.gov (United States)

Wang, Muzhou; Likhtman, Alexei E.; Olsen, Bradley D.

2015-03-01

Understanding the dynamics of rod-coil block copolymers is important for optimal design of functional nanostructured materials for organic electronics and biomaterials. Recently, we proposed a reptation theory of entangled rod-coil block copolymers, predicting the relaxation mechanisms of activated reptation and arm retraction that slow rod-coil dynamics relative to coil and rod homopolymers, respectively. In this work, we introduce a coarse-grained slip-spring model of rod-coil block copolymers to further explore these mechanisms. First, parameters of the coarse-grained model are tuned to match previous molecular dynamics simulation results for coils, rods, and block copolymers. For activated reptation, rod-coil copolymers are shown to disfavor configurations where the rod occupies curved portions of the entanglement tube of randomly varying curvature created by the coil ends. The effect of these barriers on diffusion is quantitatively captured by considering one-dimensional motion along an entanglement tube with a rough free energy potential. Finally, we analyze the crossover between the two mechanisms. The resulting dynamics from both mechanisms acting in combination is faster than from each one individually.

Method of driving control rod in reactor

International Nuclear Information System (INIS)

Osa, Hirotaka.

1986-01-01

Purpose: To improve security and safety of the reactor by reducing reactor output automatically and quickly when circulation of cooling water is stopped. Constitution: When the circulating pump is under operation, fluid pressure in the discharge pipe is transferred to the fluid room of fluid pressure cylinder via the control rod drive pipe and lift up the piston, and then the control rod is drawn out of the reactor core. When the circulating pump is lowered in its functions, discharge pipe fluid pressure decreases, fluid pressure in the fluid room decreases, and with less force of piston movement, the control rod gets lowered by its own weight. At this time, the blocked state of the opening by the piston is released, fluid flows into the room. Lowering of pressure and the control rod is promoted by transferring out fluid below the piston in the fluid room to the upper part of the piston via a small gap when the control rod falls by gravity. (Horiuchi, T.)

Hardfacing and welding rods by P/M

International Nuclear Information System (INIS)

Nayar, H.S.

1977-01-01

Certain hardfacing and welding rods are very hard and non-deformable. They are, as it is well known, generally produced by casting processes. Airco has developed a P/M process for producing these rods. The process is already practiced on a semi-production scale. In this process, the powder is poured into suitably designed and prepared molds, vibrated to pack the powder, and sintered at a temperature between the solidus and the liquidus temperatures of the alloy to produce rods with 85% or more of the theoretical density. The P/M process has some distinct advantages over the conventional casting processes. These advantages are highlighted. The process is suitable for producing Fe-, Ni-, Co-, and Cu-base hardfacing and welding rods with and without second phase hard particles such as WC. Microstructures, dimensional and density controls, weld-evaluations and hardness data are included to present evidence that the rods produced by the P/M process are suitable for various welding and hardfacing applications

Expression, purification, crystallization and preliminary crystallographic analysis of MxiH, a subunit of the Shigella flexneri type III secretion system needle

Energy Technology Data Exchange (ETDEWEB)

Deane, Janet E.; Cordes, Frank S.; Roversi, Pietro [Laboratory of Molecular Biophysics, Department of Biochemistry, University of Oxford (United Kingdom); Johnson, Steven [Laboratory of Molecular Biophysics, Department of Biochemistry, University of Oxford (United Kingdom); Sir William Dunn School of Pathology, University of Oxford (United Kingdom); Kenjale, Roma; Picking, William D.; Picking, Wendy L. [Department of Molecular Biosciences, University of Kansas (United States); Lea, Susan M., E-mail: susan.lea@biop.ox.ac.uk [Laboratory of Molecular Biophysics, Department of Biochemistry, University of Oxford (United Kingdom); Sir William Dunn School of Pathology, University of Oxford (United Kingdom); Blocker, Ariel [Sir William Dunn School of Pathology, University of Oxford (United Kingdom); Laboratory of Molecular Biophysics, Department of Biochemistry, University of Oxford (United Kingdom)

2006-03-01

A monodisperse truncation mutant of MxiH, the subunit of the S. flexneri type III secretion system needle, has been crystallized. SeMet derivatives and a uranyl derivative have undergone preliminary crystallographic analysis. A monodisperse truncation mutant of MxiH, the subunit of the needle from the Shigella flexneri type III secretion system (TTSS), has been overexpressed and purified. Crystals were grown of native and selenomethionine-labelled MxiH{sub CΔ5} and diffraction data were collected to 1.9 Å resolution. The crystals belong to space group C2, with unit-cell parameters a = 183.4, b = 28.1, c = 27.8 Å, β = 96.5°. An anomalous difference Patterson map calculated with the data from the SeMet-labelled crystals revealed a single peak on the Harker section v = 0. Inspection of a uranyl derivative also revealed one peak in the isomorphous difference Patterson map on the Harker section v = 0. Analysis of the self-rotation function indicates the presence of a twofold non-crystallographic symmetry axis approximately along a. The calculated Matthews coefficient is 1.9 Å{sup 3} Da{sup −1} for two molecules per asymmetric unit, corresponding to a solvent content of 33%.