Thermo-hydro-mechanical modelling of buffer, synthesis report

Energy Technology Data Exchange (ETDEWEB)

Toprak, E.; Mokni, N.; Olivella, S. [Universitat Politecnica de Catalunya, Barcelona (Spain); Pintado, X. [B and Tech Oy, Helsinki (Finland)

2013-08-15

This study addresses analyses of coupled thermo-hydro-mechanical (THM) processes in a scheme considered for the spent nuclear fuel repository in Olkiluoto (Finland). The finite element code CODE{sub B}RIGHT is used to perform modelling calculations. The objective of the THM modelling was to study some fundamental design parameters. The time required to reach full saturation, the maximum temperature reached in the canister, the deformations in the buffer-backfill interface, the stress-deformation balance between the buffer and the backfill, the swelling pressure developed and the homogenization process development are critical variables. Because of the complexity of the THM processes developed, only a single deposition hole has been modelled with realistic boundary conditions which take into account the entire repository. A thermal calculation has been performed to adopt appropriate boundary conditions for a reduced domain. The modelling has been done under axisymmetric conditions. As a material model for the buffer bentonite and backfill soil, the Barcelona Basic Model (BBM) has been used. Simulation of laboratory tests conducted at B and Tech under supervision of Posiva has been carried out in order to determine the fundamental mechanical parameters for modelling the behaviour of MX-80 bentonite using the BBM model. The modelling process of the buffer-backfill interface is an essential part of tunnel backfill design. The calculations will aim to determine deformations in this intersection, the behaviour of which is important for the buffer swelling. The homogenization process is a key issue as well. Porosity evolution during the saturation process is evaluated in order to check if the final saturated density accomplishes the homogenization requirements. This report also describes the effect of the existence of an air-filled gap located between the canister and the bentonite block rings in thermo-hydro-mechanical behaviour of the future spent nuclear fuel

Thermo-hydro-mechanical coupling in long-term sedimentary rock response

Science.gov (United States)

Makhnenko, R. Y.; Podladchikov, Y.

2017-12-01

Storage of nuclear waste or CO2 affects the state of stress and pore pressure in the subsurface and may induce large thermal gradients in the rock formations. In general, the associated coupled thermo-hydro-mechanical effect on long-term rock deformation and fluid flow have to be studied. Principles behind mathematical models for poroviscoelastic response are reviewed, and poroviscous model parameter, the bulk viscosity, is included in the constitutive equations. Time-dependent response (creep) of fluid-filled sedimentary rocks is experimentally quantified at isotropic stress states. Three poroelastic parameters are measured by drained, undrained, and unjacketed geomechanical tests for quartz-rich Berea sandstone, calcite-rich Apulian limestone, and clay-rich Jurassic shale. The bulk viscosity is calculated from the measurements of pore pressure growth under undrained conditions, which requires time scales 104 s. The bulk viscosity is reported to be on the order of 1015 Pa•s for the sandstone, limestone, and shale. It is found to be decreasing with the increase of pore pressure despite corresponding decrease in the effective stress. Additionally, increase of temperature (from 24 ºC to 40 ºC) enhances creep, where the most pronounced effect is reported for the shale with bulk viscosity decrease by a factor of 3. Viscous compaction of fluid-filled porous media allows a generation of a special type of fluid flow instability that leads to formation of high-porosity, high-permeability domains that are able to self-propagate upwards due to interplay between buoyancy and viscous resistance of the deforming porous matrix. This instability is known as "porosity wave" and its formation is possible under conditions applicable to deep CO2 storage in reservoirs and explains creation of high-porosity channels and chimneys. The reported experiments show that the formation of high-permeability pathways is most likely to occur in low-permeable clay-rich materials (caprock

Modelling of thermo-hydro-mechanical couplings and damage of viscoplastic rocks in the context of radioactive waste storage; Modelisation des couplages thermo-hydro-mecaniques et de l'endommagement des roches viscoplastiques dans le contexte du stockage de dechets radioactifs

Energy Technology Data Exchange (ETDEWEB)

Kharkhour, H

2002-12-01

Trying to develop a model taking into account the complex rheology of a geologic media characterized by visco-plasticity, damage and thermo-hydro-mechanical couplings is unusual in geotechnics. This is not the case for radioactive waste storage that presents specificities from several viewpoints. Indeed, the scales of time and space concerned by this type of storage are disproportionate to those of civil engineering works or mines. Another specificity of the radioactive waste storage lies in the coupled processes involved. No effect likely to compromise the long-term security of the storage could be ignored. For example this is the case of damage, a phenomenon which does not necessarily lead to a major change of the mechanical behavior of the works but can influence the permeability of the medium in relation with a migration of radionuclides. It can be conceived that this phenomenon finds all its importance in the context of the thermo-hydro-mechanical couplings of a waste storage with high activity. However, the interaction between the damage and the THM coupled processes was the object of very few research subject up to now. This. is even more true for viscoplastic media considered as ductile, and therefore, less prone to cracking than brittle media. It is exactly in this 'original' but difficult context that took place the research presented in this report. This study was dedicated to the analysis of the phenomena and the thermal, hydraulic and mechanical couplings occurring in the near and far field of a high activity radioactive waste storage. Two examples of geological media were considered in this report: the clayey rock of Callovo-Oxfordian, called ' Argilites de l'Est ', target rock of the ANDRA project to carry out a subterranean laboratory for the study of long life radioactive waste storage; and the salt rock of the. subterranean laboratory in the old salt mine of Asse in Germany. (author)

DECOVALEX - Mathematical models of coupled T-H-M processes for nuclear waste repositories. Executive summary for Phases I,II and III

International Nuclear Information System (INIS)

Jing, L.; Stephansson, O.; Tsang, C.F.; Kautsky, F.

1996-06-01

This executive summary presents the motivation, structure, objectives, methodologies and results of the first stage of the international DECOVALEX project - DECOVALEX I (1992-1995). The acronym stands for Development of Coupled Models and their Validation against Experiment in Nuclear Waste Isolation, and the project is an international effort to develop mathematical models, numerical methods and computer codes for coupled thermo-hydro-mechanical processes in fractured rocks and buffer materials for geological isolation of spent nuclear fuel and other radioactive wastes, and validate them against laboratory and field experiments. 24 refs

Coupling methodology within the software platform alliances

Energy Technology Data Exchange (ETDEWEB)

Montarnal, Ph; Deville, E; Adam, E; Bengaouer, A [CEA Saclay, Dept. de Modelisation des Systemes et Structures 91 - Gif-sur-Yvette (France); Dimier, A; Gaombalet, J; Loth, L [Agence Nationale pour la Gestion des Dechets Radioactifs (ANDRA), 92 - Chatenay Malabry (France); Chavant, C [Electricite de France (EDF), 92 - Clamart (France)

2005-07-01

CEA, ANDRA and EDF are jointly developing the software platform ALLIANCES which aim is to produce a tool for the simulation of nuclear waste storage and disposal repository. This type of simulations deals with highly coupled thermo-hydro-mechanical and chemical (T-H-M-C) processes. A key objective of Alliances is to give the capability for coupling algorithms development between existing codes. The aim of this paper is to present coupling methodology use in the context of this software platform. (author)

Coupling methodology within the software platform alliances

International Nuclear Information System (INIS)

Montarnal, Ph.; Deville, E.; Adam, E.; Bengaouer, A.; Dimier, A.; Gaombalet, J.; Loth, L.; Chavant, C.

2005-01-01

CEA, ANDRA and EDF are jointly developing the software platform ALLIANCES which aim is to produce a tool for the simulation of nuclear waste storage and disposal repository. This type of simulations deals with highly coupled thermo-hydro-mechanical and chemical (T-H-M-C) processes. A key objective of Alliances is to give the capability for coupling algorithms development between existing codes. The aim of this paper is to present coupling methodology use in the context of this software platform. (author)

Experimental study of thermo-hydro-mechanical behaviour of Callovo-Oxfordian Clay-stone

International Nuclear Information System (INIS)

Mohajerani, M.

2011-01-01

During the different phases of the exothermic radioactive waste deep disposal (excavation, operation) and after permanent closure, the host rock is submitted to various coupled mechanical, hydraulic and thermal phenomena. Hence, a thorough investigation of the thermo-hydro-mechanical behaviour of the rock is necessary to complete existing data and to better understand and model the short and long term behaviour of the Callovo-Oxfordian (COx) clay formation in Bure (Meuse/Haute-Marne - M/HM), considered by ANDRA as a potential host rock in France.In this work, the compression - swelling behaviour of the COx Clay-stone was first investigated by carrying out a series of high-pressure oedometric tests. The results, interpreted in terms of coupling between damage and swelling, showed that the magnitude of swelling was linked to the density of the fissures created during compression. In a second step, the hydro-mechanical and thermo-hydro-mechanical behaviour of the saturated Clay-stone under a mean stress close to the in situ one were investigated by using two devices with short drainage path (10 mm), namely a isotropic cell and a newly designed hollow cylinder triaxial cell with local displacement measurements. These devices helped to solve two majors problems related to testing very low permeability materials: i) a satisfactory previous sample saturation (indicated by good Skempton values) and ii) satisfactory drainage conditions. Some typical constitutive parameters (Skempton and Biot's coefficients, drained and undrained compressibility coefficients) have been determined at ambient temperature through isotropic compression tests that also confirmed the transverse isotropy of the Clay-stone. The consistency of the obtained parameters has been checked in a saturated poro-elastic framework. Two aspects of the thermo-hydro-mechanical behaviour of the COx Clay-stone have then been investigated through different heating tests and through drained and undrained isotropic

Sensitivity analysis of coupled processes and parameters on the performance of enhanced geothermal systems.

Science.gov (United States)

Pandey, S N; Vishal, Vikram

2017-12-06

3-D modeling of coupled thermo-hydro-mechanical (THM) processes in enhanced geothermal systems using the control volume finite element code was done. In a first, a comparative analysis on the effects of coupled processes, operational parameters and reservoir parameters on heat extraction was conducted. We found that significant temperature drop and fluid overpressure occurred inside the reservoirs/fracture that affected the transport behavior of the fracture. The spatio-temporal variations of fracture aperture greatly impacted the thermal drawdown and consequently the net energy output. The results showed that maximum aperture evolution occurred near the injection zone instead of the production zone. Opening of the fracture reduced the injection pressure required to circulate a fixed mass of water. The thermal breakthrough and heat extraction strongly depend on the injection mass flow rate, well distances, reservoir permeability and geothermal gradients. High permeability caused higher water loss, leading to reduced heat extraction. From the results of TH vs THM process simulations, we conclude that appropriate coupling is vital and can impact the estimates of net heat extraction. This study can help in identifying the critical operational parameters, and process optimization for enhanced energy extraction from a geothermal system.

Analysis and modeling of coupled thermo-hydro-mechanical phenomena in 3D fractured media; Analyse et modelisation des phenomenes couples thermo-hydromecaniques en milieux fractures 3D

Energy Technology Data Exchange (ETDEWEB)

Canamon Valera, I

2006-11-15

This doctoral research was conducted as part of a joint France-Spain co-tutelage PhD thesis in the framework of a bilateral agreement between two universities, the Institut National Polytechnique de Toulouse (INPT) and the Universidad Politecnica de Madrid (UPM). It concerns a problem of common interest at the national and international levels, namely, the disposal of radioactive waste in deep geological repositories. The present work is devoted, more precisely, to near-field hydrogeological aspects involving mass and heat transport phenomena. The first part of the work is devoted to a specific data interpretation problem (pressures, relative humidities, temperatures) in a multi-barrier experimental system at the scale of a few meters - the 'Mock-Up Test' of the FEBEX project, conducted in Spain. Over 500 time series are characterized in terms of spatial, temporal, and/or frequency/scale-based statistical analysis techniques. The time evolution and coupling of physical phenomena during the experiment are analyzed, and conclusions are drawn concerning the behavior and reliability of the sensors. The second part of the thesis develops in more detail the 3-Dimensional (3D) modeling of coupled Thermo-Hydro-Mechanical phenomena in a fractured porous rock, this time at the scale of a hundred meters, based on the data of the 'In-Situ Test' of the FEBEX project conducted at the Grimsel Test Site in the Swiss Alps. As a first step, a reconstruction of the 3D fracture network is obtained by Monte Carlo simulation, taking into account through optimization the geomorphological data collected around the FEBEX gallery. The heterogeneous distribution of traces observed on the cylindrical wall of the tunnel is fairly well reproduced in the simulated network. In a second step, we develop a method to estimate the equivalent permeability of a many-fractured block by extending the superposition method of Ababou et al. [1994] to the case where the permeability of

The coupled process laboratory test of highly compacted bentonite

International Nuclear Information System (INIS)

Shen Zhenyao; Li Guoding; Li Shushen; Wang Chengzu

2004-01-01

Highly compacted bentonite blocks have been heated and hydrated in the laboratory in order to simulate the thermo-hydro-mechanical (THM) coupled processes of buffer material in a high-level radioactive waste (HLW) repository. The experiment facility, which is composed of experiment barrel, heated system, high pressure water input system, temperature measure system, water content measure system and swelling stress system, is introduced in this paper. The steps of the THM coupled experiment are also given out in detail. There are total 10 highly compacted bentonite blocks used in this test. Experimental number 1-4 are the tests with the heater and the hydrated process, which temperature distribution vs. time and final moisture distribution are measured. Experimental number 5-8 are the tests with the heater and without the hydrated process, which temperature distribution vs. time and final moisture distribution are measured. Experimental number 9-10 are the tests with the heater and the hydrated process, which temperature distribution vs. time, final moisture distribution and the swelling stress distribution at some typical points vs. time are measured. The maximum test time is nearly 20 days and the minimum test time is only 8 hours. The results show that the temperature field is little affected by hydration process and stress condition, but moisture transport and stress distribution are a little affected by the thermal gradient. The results also show that the water head difference is the mainly driving force of hydration process and the swelling stress is mainly from hydration process. It will great help to understand better about heat and mass transfer in porous media and the THM coupled process in actual HLW disposal. (author)

Numerical analysis of thermo-hydro-mechanical (THM) processes in the clay based material

Energy Technology Data Exchange (ETDEWEB)

Wang, Xuerui

2016-10-06

Clay formations are investigated worldwide as potential host rock for the deep geological disposal of high-level radioactive waste (HLW). Usually bentonite is preferred as the buffer and backfill material in the disposal system. In the disposal of HLW, heat emission is one of the most important issues as it can generate a series of complex thermo-hydro-mechanical (THM) processes in the surrounding materials and thus change the material properties. In the context of safety assessment, it is important to understand the thermally induced THM interactions and the associated change in material properties. In this work, the thermally induced coupled THM behaviours in the clay host rock and in the bentonite buffer as well as the corresponding coupling effects among the relevant material properties are numerically analysed. A coupled non-isothermal Richards flow mechanical model and a non-isothermal multiphase flow model were developed based on the scientific computer codes OpenGeoSys (OGS). Heat transfer in the porous media is governed by thermal conduction and advective flow of the pore fluids. Within the hydraulic processes, evaporation, vapour diffusion, and the unsaturated flow field are considered. Darcy's law is used to describe the advective flux of gas and liquid phases. The relative permeability of each phase is considered. The elastic deformation process is modelled by the generalized Hooke's law complemented with additional strain caused by swelling/shrinkage behaviour and by temperature change. In this study, special attention has been paid to the analysis of the thermally induced changes in material properties. The strong mechanical and hydraulic anisotropic properties of clay rock are described by a transversely isotropic mechanical model and by a transversely isotropic permeability tensor, respectively. The thermal anisotropy is described by adoption of the bedding-orientation-dependent thermal conductivity. The dependency of the thermal

Numerical analysis of thermo-hydro-mechanical (THM) processes in the clay based material

International Nuclear Information System (INIS)

Wang, Xuerui

2016-01-01

Clay formations are investigated worldwide as potential host rock for the deep geological disposal of high-level radioactive waste (HLW). Usually bentonite is preferred as the buffer and backfill material in the disposal system. In the disposal of HLW, heat emission is one of the most important issues as it can generate a series of complex thermo-hydro-mechanical (THM) processes in the surrounding materials and thus change the material properties. In the context of safety assessment, it is important to understand the thermally induced THM interactions and the associated change in material properties. In this work, the thermally induced coupled THM behaviours in the clay host rock and in the bentonite buffer as well as the corresponding coupling effects among the relevant material properties are numerically analysed. A coupled non-isothermal Richards flow mechanical model and a non-isothermal multiphase flow model were developed based on the scientific computer codes OpenGeoSys (OGS). Heat transfer in the porous media is governed by thermal conduction and advective flow of the pore fluids. Within the hydraulic processes, evaporation, vapour diffusion, and the unsaturated flow field are considered. Darcy's law is used to describe the advective flux of gas and liquid phases. The relative permeability of each phase is considered. The elastic deformation process is modelled by the generalized Hooke's law complemented with additional strain caused by swelling/shrinkage behaviour and by temperature change. In this study, special attention has been paid to the analysis of the thermally induced changes in material properties. The strong mechanical and hydraulic anisotropic properties of clay rock are described by a transversely isotropic mechanical model and by a transversely isotropic permeability tensor, respectively. The thermal anisotropy is described by adoption of the bedding-orientation-dependent thermal conductivity. The dependency of the thermal

Investigation research on the evaluation of a coupled thermo-hydro-mechanical-chemical phenomena. Outline report

International Nuclear Information System (INIS)

Chijimatsu, Masakazu; Amemiya, Kiyoshi; Neyama, Atsushi; Iwata, Hiroshi; Nakagawa, Koichi; Ishihara, Yoshinao; Shiozaki, Isao; Sagawa, Hiroshi

2002-02-01

In order to realize a coupling analysis in the near field of the geological disposal system, this study has been studied on the addition of the mass transport model to the coupled thermo-hydro-mechanical analysis code (THAMES) and preliminary coupling analysis by using development environmental tool (Diffpack) for numerical analysis. (1) In order to prepare the strategy on the addition of the mass transport model to the coupled thermo-hydro-mechanical analysis code (THAMES), we have studied on the requirement of THAMES-Transport and methodology of coupling analysis. After that we set out modification plan by the Eulerian-Lagrangian (EL) method. (2) Based on the document of modification plan, we have done addition of the mass transport model to the coupled thermo-hydro-mechanical analysis code (THAMES) and carried out verification analysis in order to confirm on the accuracy of THAMES-Transport. (3) In order to understand on the behavior of NaCl in the porewater under the coupled thermo-hydro-mechanical phenomena in the HLW engineered barrier system, we have calculated coupling phenomenon by using THAMES-Transport. Transportation and concentration phenomena of NaCl are calculated but precipitation of NaCl is not occurred under the analysis conditions in this report. (4) In order to confirm about feasibility of coupling analysis under the development environmental tool (Diffpack) for numerical analysis, we have carried out on the design work and writing program of the preliminary coupling system. In this study, we have adopted existing transport model (HYDROGEOCHEM) and geochemical model (phreeqe60) for preliminary coupling system. (5) In order to confirm program correctness of preliminary coupling system, we have carried out benchmarking analysis by using existing reactive-transport analysis code (HYDROGEOCHEM). (6) We have been prepared short-range development plan based on through the modification study of THAMES and writing program of the preliminary coupling

Investigation research on the evaluation of a coupled thermo-hydro-mechanical-chemical phenomena. Result report

International Nuclear Information System (INIS)

Chijimatsu, Masakazu; Amemiya, Kiyoshi; Shiozaki, Isao; Neyama, Atsushi; Iwata, Hiroshi; Nakagawa, Koichi; Ishihara, Yoshinao; Sagawa, Hiroshi

2002-02-01

In order to realize a coupling analysis in the near field of the geological disposal system, this study has been studied on the addition of the mass transport model to the coupled thermo-hydro-mechanical analysis code (THAMES) and preliminary coupling analysis by using development environmental tool (Diffpack) for numerical analysis. (1) In order to prepare the strategy on the addition of the mass transport model to the coupled thermo-hydro-mechanical analysis code (THAMES), we have studied on the requirement of THAMES-Transport and methodology of coupling analysis. After that we set out modification plan by the Eulerian-Lagrangian (EL) method. (2) Based on the document of modification plan, we have done addition of the mass transport model to the coupled thermo-hydro-mechanical analysis code (THAMES) and carried out verification analysis in order to confirm on the accuracy of THAMES-Transport. (3) In order to understand on the behavior of NaCl in the porewater under the coupled thermo-hydro-mechanical phenomena in the HLW engineered barrier system, we have calculated coupling phenomenon by using THAMES-Transport. Transportation and concentration phenomena of NaCl are calculated but precipitation of NaCl is not occurred under the analysis conditions in this report. (4) In order to confirm about feasibility of coupling analysis under the development environmental tool (Diffpack) for numerical analysis, we have carried out on the design work and writing program of the preliminary coupling system. In this study, we have adopted existing transport model (HYDROGEOCHEM) and geochemical model (phreeqe 60) for preliminary coupling system. (5) In order to confirm program correctness of preliminary coupling system, we have carried out benchmarking analysis by using existing reactive-transport analysis code (HYDROGEOCHEM). (6) We have been prepared short-range development plan based on through the modification study of THAMES and writing program of the preliminary coupling

The importance of Thermo-Hydro-Mechanical couplings and microstructure to strain localization in 3D continua with application to seismic faults. Part I: Theory and linear stability analysis

Science.gov (United States)

Rattez, Hadrien; Stefanou, Ioannis; Sulem, Jean

2018-06-01

A Thermo-Hydro-Mechanical (THM) model for Cosserat continua is developed to explore the influence of frictional heating and thermal pore fluid pressurization on the strain localization phenomenon. A general framework is presented to conduct a bifurcation analysis for elasto-plastic Cosserat continua with THM couplings and predict the onset of instability. The presence of internal lengths in Cosserat continua enables to estimate the thickness of the localization zone. This is done by performing a linear stability analysis of the system and looking for the selected wavelength corresponding to the instability mode with fastest finite growth coefficient. These concepts are applied to the study of fault zones under fast shearing. For doing so, we consider a model of a sheared saturated infinite granular layer. The influence of THM couplings on the bifurcation state and the shear band width is investigated. Taking representative parameters for a centroidal fault gouge, the evolution of the thickness of the localized zone under continuous shear is studied. Furthermore, the effect of grain crushing inside the shear band is explored by varying the internal length of the constitutive law.

The importance of Thermo-Hydro-Mechanical couplings and microstructure to strain localization in 3D continua with application to seismic faults. Part II: Numerical implementation and post-bifurcation analysis

Science.gov (United States)

Rattez, Hadrien; Stefanou, Ioannis; Sulem, Jean; Veveakis, Manolis; Poulet, Thomas

2018-06-01

In this paper we study the phenomenon of localization of deformation in fault gouges during seismic slip. This process is of key importance to understand frictional heating and energy budget during an earthquake. A infinite layer of fault gouge is modeled as a Cosserat continuum taking into account Thermo-Hydro-Mechanical (THM) couplings. The theoretical aspects of the problem are presented in the companion paper (Rattez et al., 2017a), together with a linear stability analysis to determine the conditions of localization and estimate the shear band thickness. In this Part II of the study, we investigate the post-bifurcation evolution of the system by integrating numerically the full system of non-linear equations using the method of Finite Elements. The problem is formulated in the framework of Cosserat theory. It enables to introduce information about the microstructure of the material in the constitutive equations and to regularize the mathematical problem in the post-localization regime. We emphasize the influence of the size of the microstructure and of the softening law on the material response and the strain localization process. The weakening effect of pore fluid thermal pressurization induced by shear heating is examined and quantified. It enhances the weakening process and contributes to the narrowing of shear band thickness. Moreover, due to THM couplings an apparent rate-dependency is observed, even for rate-independent material behavior. Finally, comparisons show that when the perturbed field of shear deformation dominates, the estimation of the shear band thickness obtained from linear stability analysis differs from the one obtained from the finite element computations, demonstrating the importance of post-localization numerical simulations.

Thermo-hydro-mechanical behaviour of Boom clay; Comportement thermo-hydro-mecanique de l'argile de Boom

Energy Technology Data Exchange (ETDEWEB)

Le, T.T

2008-01-15

This thesis studied the thermo-hydro-mechanical properties of Boom clay, which was chosen to be the host material for the radioactive waste disposal in Mol, Belgium. Firstly, the research was concentrated on the soil water retention properties and the hydro-mechanical coupling by carrying out axial compression tests with suction monitoring. The results obtained permitted elaborating a rational experimental procedure for triaxial tests. Secondly, the systems for high pressure triaxial test at controlled temperature were developed to carry out compression, heating, and shearing tests at different temperatures. The obtained results showed clear visco-elasto-plastic behaviour of the soil. This behaviour was modelled by extending the thermo-elasto-plastic model of Cui et al. (2000) to creep effect. (author)

Coupled thermo-hydro-mechanical processes around a bentonite buffer embedded in Opalinus Clay - Comparison between measurements and calculations

Energy Technology Data Exchange (ETDEWEB)

Goebel, Ingeborg; Alheid, Hans-Joachim [BGR Hannover, Stilleweg 2, D-30655 Hannover (Germany); Jockwer, Norbert [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, Theodor-Heuss-Str. 4, 38122 Braunschweig (Germany); Mayor, Juan Carlos [ENRESA, Emilio Vargas 7, E-Madrid (Spain); Garcia-Sineriz, Jose Luis [AITEMIN, c/ Alenza, 1 - 28003 Madrid (Spain); Alonso, Eduardo; Munoz, Juan Jorge [International Center for Numerical Methods in Engineering, CIMNE, Edificio C-1, Campus Norte UPC, C/Gran Capitan, s/n, 08034 Barcelona (Spain); Weber, Hans Peter [NAGRA, Hardstrasse 73, CH-5430 Wettingen (Switzerland); Ploetze, Michael [ETHZ, Eidgenoessische Technische Hochschule Zuerich, ETH Zentrum, HG Raemistrasse 101, CH-8092 Zuerich (Switzerland); Klubertanz, Georg [COLENCO Power Engineering Ltd, CPE, Taefern Str. 26, 5405 Baden-Daettwil (Switzerland); Ammon, Christian [Rothpletz, Lienhard, Cie AG, Schifflaendestrasse 35, 5001 Aarau (Switzerland)

2004-07-01

The Heater Experiment at the Mont Terri Underground Laboratory consists of an engineered barrier system composed of compacted bentonite blocks around a heater. The bentonite barrier is embedded in Opalinus Clay. The aim of the project is improved understanding of thermo-hydro mechanically (THM) coupled processes. Calculations are performed by 2 Finite-Element programs, CODE-BRIGHT and MHERLIN, the former for the near-field modeling and the latter for the rock modeling. Numerical modeling is carried out during all phases of the project to give input for design tasks such as cooling and dismantling, and to finally produce verified models of the THM coupled engineered barrier system. Results of both programs are discussed in the light of the experimental findings. (authors)

DECOVALEX III PROJECT. Thermal-Hydro-Mechanical Coupled Processes in Safety Assessments. Report of Task 4

International Nuclear Information System (INIS)

Andersson, Johan

2005-02-01

A part (Task 4) of the International DECOVALEX III project on coupled thermo-hydro-mechanical (T-H-M) processes focuses on T-H-M modelling applications in safety and performance assessment of deep geological nuclear waste repositories. A previous phase, DECOVALEX II, saw a need to improve such modelling. In order to address this need Task 4 of DECOVALEX III has: Analysed two major T-H-M experiments (Task 1 and Task 2) and three different Bench Mark Tests (Task 3) set-up to explore the significance of T-H-M in some potentially important safety assessment applications. Compiled and evaluated the use of T-H-M modelling in safety assessments at the time of the year 2000. Organised a forum a forum of interchange between PA-analysts and THM modelers at each DECOVALEX III workshop. Based on this information the current report discusses the findings and strives for reaching recommendations as regards good practices in addressing coupled T-H-M issues in safety assessments. The full development of T-H-M modelling is still at an early stage and it is not evident whether current codes provide the information that is required. However, although the geosphere is a system of fully coupled processes, this does not directly imply that all existing coupled mechanisms must be represented numerically. Modelling is conducted for specific purposes and the required confidence level should be considered. It is necessary to match the confidence level with the modelling objective. Coupled THM modelling has to incorporate uncertainties. These uncertainties mainly concern uncertainties in the conceptual model and uncertainty in data. Assessing data uncertainty is important when judging the need to model coupled processes. Often data uncertainty is more significant than the coupled effects. The emphasis on the need for THM modelling differs among disciplines. For geological radioactive waste disposal in crystalline and other similar hard rock formations DECOVALEX III shows it is essential to

DECOVALEX III PROJECT. Thermal-Hydro-Mechanical Coupled Processes in Safety Assessments. Report of Task 4

Energy Technology Data Exchange (ETDEWEB)

Andersson, Johan [JA Streamflow AB, Aelvsjoe (Sweden)

2005-02-15

A part (Task 4) of the International DECOVALEX III project on coupled thermo-hydro-mechanical (T-H-M) processes focuses on T-H-M modelling applications in safety and performance assessment of deep geological nuclear waste repositories. A previous phase, DECOVALEX II, saw a need to improve such modelling. In order to address this need Task 4 of DECOVALEX III has: Analysed two major T-H-M experiments (Task 1 and Task 2) and three different Bench Mark Tests (Task 3) set-up to explore the significance of T-H-M in some potentially important safety assessment applications. Compiled and evaluated the use of T-H-M modelling in safety assessments at the time of the year 2000. Organised a forum a forum of interchange between PA-analysts and THM modelers at each DECOVALEX III workshop. Based on this information the current report discusses the findings and strives for reaching recommendations as regards good practices in addressing coupled T-H-M issues in safety assessments. The full development of T-H-M modelling is still at an early stage and it is not evident whether current codes provide the information that is required. However, although the geosphere is a system of fully coupled processes, this does not directly imply that all existing coupled mechanisms must be represented numerically. Modelling is conducted for specific purposes and the required confidence level should be considered. It is necessary to match the confidence level with the modelling objective. Coupled THM modelling has to incorporate uncertainties. These uncertainties mainly concern uncertainties in the conceptual model and uncertainty in data. Assessing data uncertainty is important when judging the need to model coupled processes. Often data uncertainty is more significant than the coupled effects. The emphasis on the need for THM modelling differs among disciplines. For geological radioactive waste disposal in crystalline and other similar hard rock formations DECOVALEX III shows it is essential to

Flexible parallel implicit modelling of coupled thermal-hydraulic-mechanical processes in fractured rocks

Science.gov (United States)

Cacace, Mauro; Jacquey, Antoine B.

2017-09-01

Theory and numerical implementation describing groundwater flow and the transport of heat and solute mass in fully saturated fractured rocks with elasto-plastic mechanical feedbacks are developed. In our formulation, fractures are considered as being of lower dimension than the hosting deformable porous rock and we consider their hydraulic and mechanical apertures as scaling parameters to ensure continuous exchange of fluid mass and energy within the fracture-solid matrix system. The coupled system of equations is implemented in a new simulator code that makes use of a Galerkin finite-element technique. The code builds on a flexible, object-oriented numerical framework (MOOSE, Multiphysics Object Oriented Simulation Environment) which provides an extensive scalable parallel and implicit coupling to solve for the multiphysics problem. The governing equations of groundwater flow, heat and mass transport, and rock deformation are solved in a weak sense (either by classical Newton-Raphson or by free Jacobian inexact Newton-Krylow schemes) on an underlying unstructured mesh. Nonlinear feedbacks among the active processes are enforced by considering evolving fluid and rock properties depending on the thermo-hydro-mechanical state of the system and the local structure, i.e. degree of connectivity, of the fracture system. A suite of applications is presented to illustrate the flexibility and capability of the new simulator to address problems of increasing complexity and occurring at different spatial (from centimetres to tens of kilometres) and temporal scales (from minutes to hundreds of years).

Flexible parallel implicit modelling of coupled thermal–hydraulic–mechanical processes in fractured rocks

Directory of Open Access Journals (Sweden)

M. Cacace

2017-09-01

Full Text Available Theory and numerical implementation describing groundwater flow and the transport of heat and solute mass in fully saturated fractured rocks with elasto-plastic mechanical feedbacks are developed. In our formulation, fractures are considered as being of lower dimension than the hosting deformable porous rock and we consider their hydraulic and mechanical apertures as scaling parameters to ensure continuous exchange of fluid mass and energy within the fracture–solid matrix system. The coupled system of equations is implemented in a new simulator code that makes use of a Galerkin finite-element technique. The code builds on a flexible, object-oriented numerical framework (MOOSE, Multiphysics Object Oriented Simulation Environment which provides an extensive scalable parallel and implicit coupling to solve for the multiphysics problem. The governing equations of groundwater flow, heat and mass transport, and rock deformation are solved in a weak sense (either by classical Newton–Raphson or by free Jacobian inexact Newton–Krylow schemes on an underlying unstructured mesh. Nonlinear feedbacks among the active processes are enforced by considering evolving fluid and rock properties depending on the thermo-hydro-mechanical state of the system and the local structure, i.e. degree of connectivity, of the fracture system. A suite of applications is presented to illustrate the flexibility and capability of the new simulator to address problems of increasing complexity and occurring at different spatial (from centimetres to tens of kilometres and temporal scales (from minutes to hundreds of years.

Thermo-hydro-mechanical modelling of fractured rock masses application to radioactive wastes storage

International Nuclear Information System (INIS)

Vuillod, E.

1995-01-01

This work belongs to the Decovalex project (international cooperative project for the development of coupled models and their validation against experiments in nuclear waste isolation) of thermo-hydro-mechanical (THM) modeling of fractured rock massifs inside which high level radioactive waste disposal sites are simulated. The mathematical laws controlling the behaviour of the environment are resolved analytically in the case of a continuous environment (definition of an equivalent environment) and numerically if the environment is discontinuous (modeling of joints behaviour). The coupled THM models strongly influence the behaviour of a model. Modeling performed with the UDEC code shows the importance of HM couplings depending on whether the calculations are made in permanent or transient regime, and the influence of the loading path in the case of TM modeling. The geometry of fractures also influences the behaviour of the model. Studying the connexity of a fractures network allows to determine its degree of homogeneity. The comparison between two methods, continuous environment and discontinuous environment, has been carried out by determining the permeability tensor and the stress-deformation relations on fractured test-samples. It shows the differences in behaviour between an homogenized environment and a discrete environment. Finally two exercises of THM modeling of radioactive waste disposal sites illustrate the researches carried out. A far field model has permitted to compare the results obtained with calculation codes using different logics. The second model, a near field one, focusses more on the importance played by fracturing on the behaviour of the massif. The high density of the reference network has required some mathematical developments, in order to determine the representative equivalent volume (continuous approaches), and some mathematical analyses, to correctly simplify the environment (discontinuous approaches). These methods and analyses are

Numerical Analysis of a Class of THM Coupled Model for Porous Materials

Science.gov (United States)

Liu, Tangwei; Zhou, Jingying; Lu, Hongzhi

2018-01-01

We consider the coupled models of the Thermo-hydro-mechanical (THM) problem for porous materials which arises in many engineering applications. Firstly, mathematical models of the THM coupled problem for porous materials were discussed. Secondly, for different cases, some numerical difference schemes of coupled model were constructed, respectively. Finally, aassuming that the original water vapour effect is neglectable and that the volume fraction of liquid phase and the solid phase are constants, the nonlinear equations can be reduced to linear equations. The discrete equations corresponding to the linear equations were solved by the Arnodli method.

Development of coupled models and their validation against experiments -DECOVALEX project

International Nuclear Information System (INIS)

Stephansson, O.; Jing, L.; Kautsky, F.

1995-01-01

DECOVALEX is an international co-operative research project for theoretical and experimental studies of coupled thermal, hydrological and mechanical processes in hard rocks. Different mathematical models and computer codes have been developed by research teams from different countries. These models and codes are used to study the so-called Bench Mark Test and Test Case problems developed within this project. Bench-Mark Tests are defined as hypothetical initial-boundary value problems of a generic nature, and Test Cases are experimental investigations of part or full aspects of coupled thermo-hydro-mechanical processes in hard rocks. Analytical and semi-analytical solutions related to coupled T-H-M processes are also developed for problems with simpler geometry and initial-boundary conditions. These solutions are developed to verify algorithms and their computer implementations. In this contribution the motivation, organization and approaches and current status of the project are presented, together with definitions of Bench-Mark Tests and Test Case problems. The definition and part of results for a BMT problem (BMT3) for a near-field repository model are described as an example. (authors). 3 refs., 11 figs., 3 tabs

Coupled thermo-hydro-mechanical calculations of the water saturation phase of a KBS-3 deposition hole. Influence of hydraulic rock properties on the water saturation phase

International Nuclear Information System (INIS)

Boergesson, Lennart; Hernelind, J.

1999-12-01

The wetting process in deposition holes designed according to the KBS-3-concept has been simulated with finite element calculations of the thermo-hydro-mechanical processes in the buffer, backfill and surrounding rock. The buffer material has been modelled according to the preliminary material models developed for swelling clay. The properties of the rock have been varied in order to investigate the influence of the rock properties and the hydraulic conditions on the wetting processes. In the modelling of the test holes the permeability of the rock matrix, the water supply from the backfill, the water pressure in the surrounding rock, the permeability of the disturbed zone around the deposition hole, the water retention properties of the rock, and the transmissivity of two fractures intersecting the deposition hole have been varied. The calculations indicate that the wetting takes about 5 years if the water pressure in the rock is high and if the permeability of the rock is so high that the properties of the bentonite determine the wetting rate. However, it may take considerably more than 30 years if the rock is very tight and the water pressure in the rock is low. The calculations also show that the influence of the rock structure is rather large except for the influence of the transmissivity T of the fractures, which turned out to be insignificant for the values used in the calculations

Couplings in multiphasic geo-materials: temperature and chemistry effects

International Nuclear Information System (INIS)

Ghasemzadeh, H.

2006-05-01

Transport of chemical components in soil through water is the major cause of pollution of the soil. This transport takes place around landfills and nuclear waste storage areas, tailings and mine wastes, and so on. A great number of these sites are unsaturated of water and in some cases heat can change the fate of chemical species, that lead us to a coupled problem. In this dissertation, numerical simulation with an existent thermo-hydro-mechanical model and theoretical modeling and numerical simulation of transport and interactions of one chemical species in multiphase media are presented. Integrated THM model in the Code-Aster is presented. Excavation, engineering barrier and thermal load of waste nuclear storage well are modeled. Verification of model is presented with these simulations. A thermo-hydro-mechanical behaviour coupled with chemical phenomena is presented with a fully coupled method that water, gas, chemical species and soil skeleton were considered as constituents and corresponding unknowns are temperature, water pressure, gas pressure, chemical concentration and displacements. For each constituent, mass balance equation and linear momentum equation are written and solved simultaneously to find related unknowns. The results of this model have been compared with the theoretical and experimental results existing in the literature. Furthermore, results of some applications of this model are included. Some areas where further work is required are identified. In particular, there is a need to perform experiments to obtain necessary soil parameters to permit accurate modelling of the heat and contaminant transport in unsaturated soils. (author)

Experiments on thermo-hydro-mechanical behaviour of Opalinus Clay at Mont Terri rock laboratory, Switzerland

Directory of Open Access Journals (Sweden)

Paul Bossart

2017-06-01

Full Text Available Repositories for deep geological disposal of radioactive waste rely on multi-barrier systems to isolate waste from the biosphere. A multi-barrier system typically comprises the natural geological barrier provided by the repository host rock – in our case the Opalinus Clay – and an engineered barrier system (EBS. The Swiss repository concept for spent fuel and vitrified high-level waste (HLW consists of waste canisters, which are emplaced horizontally in the middle of an emplacement gallery and are separated from the gallery wall by granular backfill material (GBM. We describe here a selection of five in-situ experiments where characteristic hydro-mechanical (HM and thermo-hydro-mechanical (THM processes have been observed. The first example is a coupled HM and mine-by test where the evolution of the excavation damaged zone (EDZ was monitored around a gallery in the Opalinus Clay (ED-B experiment. Measurements of pore-water pressures and convergences due to stress redistribution during excavation highlighted the HM behaviour. The same measurements were subsequently carried out in a heater test (HE-D where we were able to characterise the Opalinus Clay in terms of its THM behaviour. These yielded detailed data to better understand the THM behaviours of the granular backfill and the natural host rock. For a presentation of the Swiss concept for HLW storage, we designed three demonstration experiments that were subsequently implemented in the Mont Terri rock laboratory: (1 the engineered barrier (EB experiment, (2 the in-situ heater test on key-THM processes and parameters (HE-E experiment, and (3 the full-scale emplacement (FE experiment. The first demonstration experiment has been dismantled, but the last two ones are on-going.

Basic rock properties for the thermo-hydro-mechanical analysis of a high-level radioactive waste repository

Energy Technology Data Exchange (ETDEWEB)

Kim, Jhin Wung; Kang, Chul Hyung

1999-04-01

Deep geological radioactive waste disposal is generally based on the isolation of the waste from the biosphere by multiple barriers. The host rock is one of these barriers which should provide a stable mechanical and chemical environment for the engineered barriers. In the evaluation of the safety of the high-level radioactive waste disposal systems, an important part of the safety analysis is an assessment of the coupling or interaction between thermal, hydrological, and mechanical effects. In order to do this assessment, adequate data on the characteristics of different host rocks are necessary. The properties of the rock and rock discontinuity are very complex and their values vary in a wide range. The accuracy of the result of the assessment depends on the values of these properties used. The present study is an attempt to bring together and condense data for the basic properties of various rock masses, which are needed in the thermo-hydro-mechanical analysis for the deep geological radioactive waste repository. The testing and measurement methods for these basic properties are also presented. Domestic data for deep geological media should be supplemented in the future, due to the insufficiency and the lack of accuracy of the data available at present. (author). 28 refs., 21 figs.

Basic rock properties for the thermo-hydro-mechanical analysis of a high-level radioactive waste repository

International Nuclear Information System (INIS)

Kim, Jhin Wung; Kang, Chul Hyung

1999-04-01

Deep geological radioactive waste disposal is generally based on the isolation of the waste from the biosphere by multiple barriers. The host rock is one of these barriers which should provide a stable mechanical and chemical environment for the engineered barriers. In the evaluation of the safety of the high-level radioactive waste disposal systems, an important part of the safety analysis is an assessment of the coupling or interaction between thermal, hydrological, and mechanical effects. In order to do this assessment, adequate data on the characteristics of different host rocks are necessary. The properties of the rock and rock discontinuity are very complex and their values vary in a wide range. The accuracy of the result of the assessment depends on the values of these properties used. The present study is an attempt to bring together and condense data for the basic properties of various rock masses, which are needed in the thermo-hydro-mechanical analysis for the deep geological radioactive waste repository. The testing and measurement methods for these basic properties are also presented. Domestic data for deep geological media should be supplemented in the future, due to the insufficiency and the lack of accuracy of the data available at present. (author). 28 refs., 21 figs

Computational thermo-hydro-mechanics for freezing and thawing multiphase geological media in the finite deformation range

Science.gov (United States)

Sun, W.; Na, S.

2017-12-01

A stabilized thermo-hydro-mechanical (THM) finite element model is introduced to investigate the freeze-thaw action of frozen porous media in the finite deformation range. By applying the mixture theory, frozen soil is idealized as a composite consisting of three phases, i.e., solid grain, unfrozen water and ice crystal. A generalized hardening rule at finite strain is adopted to replicate how the elasto-plastic responses and critical state evolve under the influence of phase transitions and heat transfer. The enhanced particle interlocking and ice strengthening during the freezing processes and the thawing-induced consolidation at the geometrical nonlinear regimes are both replicated in numerical examples. The numerical issues due to lack of two-fold inf-sup condition and ill-conditioning of the system of equations are addressed. Numerical examples for engineering applications at cold region are analyzed via the proposed model to predict the impacts of changing climate on infrastructure at cold regions.

裂隙岩体水-冰相变及低温温度场-渗流场-应力场耦合研究%WATER-ICE PHASE TRANSITION AND THERMO-HYDRO-MECHANICAL COUPLING AT LOW TEMPERATURE IN FRACTURED ROCK

Institute of Scientific and Technical Information of China (English)

刘泉声; 康永水; 刘滨; 朱元广

2011-01-01

The problem of freezing-thawing damage of rock mass involves thermo-hydro-mechanic al(THM) coupling at low temperature. Based on the phase transition theory and the energy conservation principle, the expression of frozen ratio is derived. Using the dual-porosity medium theory, the governing equations of THM coupling of freezing rock are obtained according to the law of mass conservation, the law of energy conservation and the principle of static equilibrium. Finally, considering the influence of freezing process on permeability, an example of fractured tunnel is given to reveal the distribution of temperature field, stress field and pore pressure under THM coupling condition by using the method of equivalent thermal expansion coefficient.%岩体冻融损伤涉及低温环境下温度场、渗流场和应力场的耦合问题.基于水-冰相变理论和能量守恒原理,得出冻结率表达式.运用双重孔隙介质模型理论,根据质量守恒定律、能量守恒定律及静力平衡原理,得出冻结条件下裂隙岩体的温度场-渗流场-应力场(THM)耦合控制方程.最后,通过1个含裂隙隧道低温THM耦合算例,将围岩当作岩块与裂隙介质组成的系统,采用等效热膨胀系数法对夹冰(含水)裂隙的冻胀效应进行模拟,并考虑冻结过程对岩体渗透系数的影响,研究低温THM耦合条件下的温度场、应力场及孔隙压力等的分布规律.

Role of temperature and composition on the thermal-hydro-mechanical coupling of concretes

International Nuclear Information System (INIS)

Brue, Flore

2009-01-01

The French project of the storage of nuclear wastes, which is managed by the Andra, needs some experimental data on the durability of the concrete. Loadings which are taken into account are the desaturation/re-saturation processes, the heat load and the mechanical evolution. Hence this study focuses on the coupling thermo-hydro-mechanical on concretes of the research program of Andra, made with CEM I and CEM V/A cement type. The water saturation degree and shrinkages of materials, which are subjected to desiccation or re-saturation, are dependent on the imposed thermal and hydrous conditions and on their microstructural characteristics. Moreover the study of the mechanical evolution is gone further at 20 C in function of the water saturation degree. Different short-term tests highlight a hydrous damage, which determine the mechanical behaviour. The long-term study of desiccation creep shows the coupling between the durability, the mechanical evolution and the desiccation. (author)

A three-dimensional coupled thermo-hydro-mechanical model for deformable fractured geothermal systems

DEFF Research Database (Denmark)

Salimzadeh, Saeed; Paluszny, Adriana; Nick, Hamidreza M.

2018-01-01

A fully coupled thermal-hydraulic-mechanical (THM) finite element model is presented for fractured geothermal reservoirs. Fractures are modelled as surface discontinuities within a three-dimensional matrix. Non-isothermal flow through the rock matrix and fractures are defined and coupled to a mec......A fully coupled thermal-hydraulic-mechanical (THM) finite element model is presented for fractured geothermal reservoirs. Fractures are modelled as surface discontinuities within a three-dimensional matrix. Non-isothermal flow through the rock matrix and fractures are defined and coupled....... The model has been validated against several analytical solutions, and applied to study the effects of the deformable fractures on the injection of cold water in fractured geothermal systems. Results show that the creation of flow channelling due to the thermal volumetric contraction of the rock matrix...

Thermo-hydro-mechanical behavior of fractured rock mass

International Nuclear Information System (INIS)

Coste, F.

1997-12-01

The purpose of this research is to model Thermo-Hydro-Mechanical behavior of fractured rock mass regarding a nuclear waste re-depository. For this, a methodology of modeling was proposed and was applied to a real underground site (EDF site at Nouvelle Romanche). This methodology consists, in a first step, to determine hydraulic and mechanical REV. Beyond the greatest of these REV, development of a finite element code allows to model all the fractures in an explicit manner. The homogenized mechanical properties are determined in drained and undrained boundary conditions by simulating triaxial tests that represent rock mass subject to loading. These simulations allow to study the evolution of hydraulic and mechanical properties as a function of stress state. Drained and undrained boundary conditions enable to discuss the validity of assimilation of a fractured rock mass to a porous medium. The simulations lead to a better understanding of the behavior of the fractured rock masses and allow to show the dominant role of the shear behavior of the fractures on the hydraulic and mechanical homogenized properties. From a thermal point of view, as long as conduction is dominant, thermal properties of the rock mass are almost the same as those the intact rock. (author)

FEBEX Full-Scalle Engineered Barriers Experiment in Crystalline Host Rock Preoperational Thermo-Hydro-Mechanical (THM) Modelling of the Mock Up Test

International Nuclear Information System (INIS)

1998-01-01

The object of this report is to present and discuss the results of a series of 1-D and 2-D coupled thermo-hydro-mechanical (THM) and 2-D coupled thermo-hydro-mechanical (THM) analyses modelling the FEBEX mock-up test. The analyses have been carried out during the preoperational storage of the test and attempt to incorporate all available information obtained from laboratory characterisation work. The aim is not only to offer the best estimate of test performance using current models and information but also to provide a basis for future model improvements. Both the theoretical framework adopted in the analysis and the computer code employed are briefly described. The set of parameters used in the computation is then presented with particular reference to the source from which they have been derived. Initial and boundary condition are also defined. The results of a 1-D radially symmetric analysis are used to examine the basic patterns of thermal, hydraulic and mechanical behaviour of the test. A set of sensitivity analyses has been carried out in order to check the effects that the variation of a number of important parameters has on test results. Only in this way it is possible to acquire a proper understanding of the internal structure of the problem and of the interactions between the various phenomena occurring in the buffer. A better reproduction of the geometry of the test is achieved by means of a 2-D mesh representing and axisymmetric longitudinal section. Due to two-dimensional effects, the analyses carried out using this geometry exhibit some differences when compared with the results of the 1-D case, but the basic test behaviour is very similar. The test was started with an initial flooding stage with the purpose of closing the gaps between bentonite blocks. A limited number of compilations using recently developed joint elements have been performed to assess approximately the effect of this initial step on subsequent test behaviour. The analyses reported

Heater test in the Opalinus Clay of the Mont Terri URL. Gas release and water redistribution - Contribution to heater experiment (HE); Rock and bentonite thermo-hydro-mechanical (THM) processes in the nearfield

International Nuclear Information System (INIS)

Jockwer, N.; Wieczorek, K.

2006-06-01

Beside salt and granite, clay formations are investigated as potential host rocks for disposing radioactive waste. In Switzerland in the canton Jura close to the city of St. Ursanne, an underground laboratory was built in the vicinity of the reconnaissance gallery of a motorway tunnel. Since 1995, a consortium of 12 international organisations is running this laboratory for investigating the suitability of the Opalinus clay formation with regard to disposal of radioactive waste. In 1999, the Heater Experiment B (HE-B) was started for investigating the coupled thermo-hydro-mechanical (THM) processes of the Opalinus clay in interaction with the bentonite buffer. The principal contractors of this project were the Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), the Empresa Nacional de Residuos Radiactivos S. A. (ENRESA), the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, and the National Cooperative for the Disposal of Radioactive Waste (NAGRA). GRS participated in that experiment for determining the subjects of gas generation, gas release, water content, and water redistribution in the Opalinus clay during heating. This was achieved by analysing gas and water samples from the test field before, during, and after the heating period and by performing geoelectric tomography measurements in the heated region. The in-situ measurements were supported by an additional laboratory programme. This report deals with the work of GRS performed in this project during the years 1999 to 2005. All the results obtained in the frame of the project are presented. Additional laboratory measurements conducted by the Pore Water Laboratory at CIEMAT in Madrid are also presented. The participation of GRS was funded by German Ministry of Economics and Labour (BMWA) under the contract No. 02 E 9602 and by the Commission of the European Communities under the contract No. FIKW.CT-2001-00132. (orig.)

Thermo-hydro-mechanical behavior of argillite

International Nuclear Information System (INIS)

Tran, Duy Thuong; Dormieux, Luc; Lemarchand, Eric; Skoczylas, Frederic

2012-01-01

Document available in extended abstract form only. Argillite is a very low permeability geo-material widely encountered: that is the reason why it is an excellent candidate for the storage of long-term nuclear waste depositories. This study focuses on argillites from Meuse-Haute-Marne (East of France) which forms a geological layer located approximately 400 m and 500 m depth. We know that this material is made up of a mixture of shale, quartz and calcite phases. The multi-scale definition of this material suggests the derivation of micro-mechanics reasonings in order to better account for the mechanisms occurring at the local (nano and micro-) scale and controlling the macroscopic mechanical behavior. In this work, up-scaling techniques are used in the context of thermo-hydro-mechanical couplings. The first step consists in clarifying the morphology of the microstructure at the relevant scales (particles arrangement, pore size distribution) and identifying the mechanisms that take place at those scales. These local informations provide the input data of micro-mechanics based models. Schematic picture of the microstructure where the argillite material behaves as a dual-porosity, with liquid in both micro-pores and interlayer space in between clay solid platelets, seems a reasonable starting point for this micro-mechanical modelling of clay. This allows us to link the physical phenomena (swelling clays) and the mechanical properties (elastic moduli, Poisson's ratio). At the pressure applied by the fluid on the solid platelets appears as the sum of the uniform pressure in the micro-pores and of a swelling overpressure depending on the distance between platelets and on the ion concentration in the micro-pores. The latter is proved to be responsible for a local elastic modulus of physical origin. This additional elastic component may strongly be influenced by both relative humidity and temperature. A first contribution of this study is to analysing this local elastic

Performance assessment of coupled processes

International Nuclear Information System (INIS)

Pigford, T.H.

1987-01-01

The author considers all processes to be coupled. For example, a waste package heats the surrounding rock and its pore water, creating gradients in density and pressure that result in increased water flow. That process can be described as coupled, in that the flow is a consequence of heating. In a narrower sense, one speaks also of the more weakly coupled transport processes, expressed by the Onsager reciprocal relations, that state that a transport current, i.e., flux, of heat is accompanied by a small transport current of material, as evidenced in isotope separation by thermal diffusion, the Thompson effect in thermoelectricity, etc. This paper presents a performance assessment of coupled processes

Clinical processes in behavioral couples therapy.

Science.gov (United States)

Fischer, Daniel J; Fink, Brandi C

2014-03-01

Behavioral couples therapy is a broad term for couples therapies that use behavioral techniques based on principles of operant conditioning, such as reinforcement. Behavioral shaping and rehearsal and acceptance are clinical processes found across contemporary behavioral couples therapies. These clinical processes are useful for assessment and case formulation, as well as teaching couples new methods of conflict resolution. Although these clinical processes assist therapists in achieving efficient and effective therapeutic change with distressed couples by rapidly stemming couples' corrosive affective exchanges, they also address the thoughts, emotions, and issues of trust and intimacy that are important aspects of the human experience in the context of a couple. Vignettes are provided to illustrate the clinical processes described. (PsycINFO Database Record (c) 2014 APA, all rights reserved).

BENCHPAR PROJECT. How to Incorporate ThermaI-Hydro-Mechanical Coupled Processes into Performance Assessments and Design Studies for Radioactive Waste Disposal in Geological Formations. Guidance Document

International Nuclear Information System (INIS)

Stephansson, O.; Andersson, Johan

2005-02-01

The objective of this Guidance Document is to provide advice on how to incorporate thermo-hydro-mechanical (THM) coupled processes into Performance Assessments (PAS) and design studies for radioactive waste disposal in geological formations to be experienced in a European context. The document has been generated by the EU research project BENCHPAR: Benchmark Tests and Guidance on Coupled Processes for Performance Assessment of Nuclear Waste Repositories. The document starts in Section 1 with an explanation of why numerical analyses incorporating THM mechanisms are required for radioactive waste studies and provides background material on the subject. Then, the THM processes and their interactions are explained in Section 2. Three case examples of THM numerical analysis are presented in Section 3 to illustrate the type of work that can be conducted to study the near-field, upscaling, and the far-field. For the three cases, there is discussion on the main findings, the relevance to a safety case, the relative importance of the different couplings, and the uncertainties involved. The importance and priority of the THM couplings are then summarized in Section 4. It is especially important to be able to technically audit the numerical analyses in order to establish that all the relevant variables, parameters and mechanisms have been included in the modelling and hence that the numerical model adequately represents the rock and engineering reality. Accordingly, recommended soft and hard auditing procedures are presented in Section 5. In this Guidance Document, we emphasize especially that the most important step in numerical modelling is not executing the calculations per se, but the earlier conceptualization of the problem regarding the dominant processes, the material properties and parameters, the engineering perturbations, and their mathematical presentations. The associated modelling component of addressing the uncertainties and estimating their influence on the

Investigation research on the evaluation of a coupled thermo-hydro-mechanical-chemical phenomena. 2. Result report

International Nuclear Information System (INIS)

Ishihara, Yoshinao; Ito Takaya; Chijimatsu, Masakazu; Amemiya, Kiyoshi; Shiozaki, Isao; Neyama, Atsushi; Tanaka, Yumiko

2003-02-01

In order to realize a coupling analysis in the near field of the geological disposal system, the coupling analysis code on the thermo-hydro-mechanical-chemical phenomena by THAMES, Dtransu and phreeqe60, which are existing analysis code, is developed in this study. And we carried out the case analysis on the thermo-hydro-mechanical-chemical phenomena by this code. (1) We have developed coupling analysis system to manage coupling analysis and to control coupling process automatically for THAMES (thermo-hydro-mechanical analysis code), Dtransu (mass transport analysis code) and phreeqe60 (geochemical analysis code). (2) Some supporting module, which includes transfer of dissolution concentration and total concentration (dissolution + precipitation concentration), was prepared as a functional expansion. And in order to treat multi-chemical elements, we have codified mass transport analysis code. (3) We have prepared hydraulic conductivity module of buffer material depending on change of dry density due to chemical equilibrium (dissolution and precipitation of minerals), and change of concentration of NaCl solutions. After THAMES, Dtransu, phreeqe60 and hydraulic conductivity module were installed in the COUPLYS, sensitivity analysis was carried out to check basic operation. (4) In order to confirm the applicability of the developed THMC analysis code, we have carried out case analysis on 1-dimensional and 3-dimensional model which including vitrified waste, over-pack, buffer material and rock in the HLW near-field. (author)

Couplings in multiphasic geo-materials: temperature and chemistry effects; Couplages dans les geomateriaux multiphasiques: effets de la temperature et de la chimie

Energy Technology Data Exchange (ETDEWEB)

Ghasemzadeh, H.

2006-05-15

Transport of chemical components in soil through water is the major cause of pollution of the soil. This transport takes place around landfills and nuclear waste storage areas, tailings and mine wastes, and so on. A great number of these sites are unsaturated of water and in some cases heat can change the fate of chemical species, that lead us to a coupled problem. In this dissertation, numerical simulation with an existent thermo-hydro-mechanical model and theoretical modeling and numerical simulation of transport and interactions of one chemical species in multiphase media are presented. Integrated THM model in the Code-Aster is presented. Excavation, engineering barrier and thermal load of waste nuclear storage well are modeled. Verification of model is presented with these simulations. A thermo-hydro-mechanical behaviour coupled with chemical phenomena is presented with a fully coupled method that water, gas, chemical species and soil skeleton were considered as constituents and corresponding unknowns are temperature, water pressure, gas pressure, chemical concentration and displacements. For each constituent, mass balance equation and linear momentum equation are written and solved simultaneously to find related unknowns. The results of this model have been compared with the theoretical and experimental results existing in the literature. Furthermore, results of some applications of this model are included. Some areas where further work is required are identified. In particular, there is a need to perform experiments to obtain necessary soil parameters to permit accurate modelling of the heat and contaminant transport in unsaturated soils. (author)

Thermo-hydro-mechanical tests of buffer material

International Nuclear Information System (INIS)

Pintado, X.; Hassan, Md. M.; Martikainen, J.

2013-10-01

MX-80 bentonite is the reference clay material for the buffer component planned to be used in the deep geological repository for the disposal of spent nuclear fuel in Finland. The buffer presents complex thermo-hydro-mechanical behavior which is modeled with different constitutive models for heat flow, water flow and stress-strain evolution in the buffer. Thermo, hydro and mechanical models need parameters to evaluate the THM-behavior. These modeling parameters were determined by performing series of laboratory experiments as follows: Water retention curve tests were performed on compacted bentonite samples, encompassing a range of initial dry density values from 1397 to 1718 kg/m 3 as the initial water content was around of 5-8 %. The water retention curve was determined by imposing different suctions to the samples and the suctions were then checked using capacitive hygrometer and chilled mirror psychrometer. Oedometer tests were performed on compacted bentonite samples, encompassing a range of initial dry density values from 1590 to 1750 kg/m 3 as the initial water content was around of 6 %. Samples were saturated with tap water, 35 or 70 g/L salt solutions. Infiltration tests were performed on compacted unsaturated bentonite samples, encompassing a range of initial dry density values from 1400 to 1720 kg/m 3 as the initial water content was approximately between 4-7 %. Samples were saturated with tap water, 0.87, 35 or 70 g/L salt solutions. Tortuosity tests were performed on bentonite samples, encompassing a range of dry density values from 1460 to 1750 kg/m 3 and the degree of saturation varied between 33-93 %. Thermal conductivity tests were performed on compacted bentonite samples, encompassing a range of dry density values from 1545 to 1715 kg/m 3 and the degree of saturation varied between 31-88 %. The measurement was performed using a thermal needle probe. The general trend of all analyzed parameters was as expected when dry density, water content, and

Thermo-hydro-mechanical tests of buffer material

Energy Technology Data Exchange (ETDEWEB)

Pintado, X.; Hassan, Md. M.; Martikainen, J. [B and Tech Oy, Helsinki (Finland)

2013-10-15

MX-80 bentonite is the reference clay material for the buffer component planned to be used in the deep geological repository for the disposal of spent nuclear fuel in Finland. The buffer presents complex thermo-hydro-mechanical behavior which is modeled with different constitutive models for heat flow, water flow and stress-strain evolution in the buffer. Thermo, hydro and mechanical models need parameters to evaluate the THM-behavior. These modeling parameters were determined by performing series of laboratory experiments as follows: Water retention curve tests were performed on compacted bentonite samples, encompassing a range of initial dry density values from 1397 to 1718 kg/m{sup 3} as the initial water content was around of 5-8 %. The water retention curve was determined by imposing different suctions to the samples and the suctions were then checked using capacitive hygrometer and chilled mirror psychrometer. Oedometer tests were performed on compacted bentonite samples, encompassing a range of initial dry density values from 1590 to 1750 kg/m{sup 3} as the initial water content was around of 6 %. Samples were saturated with tap water, 35 or 70 g/L salt solutions. Infiltration tests were performed on compacted unsaturated bentonite samples, encompassing a range of initial dry density values from 1400 to 1720 kg/m{sup 3} as the initial water content was approximately between 4-7 %. Samples were saturated with tap water, 0.87, 35 or 70 g/L salt solutions. Tortuosity tests were performed on bentonite samples, encompassing a range of dry density values from 1460 to 1750 kg/m{sup 3} and the degree of saturation varied between 33-93 %. Thermal conductivity tests were performed on compacted bentonite samples, encompassing a range of dry density values from 1545 to 1715 kg/m{sup 3} and the degree of saturation varied between 31-88 %. The measurement was performed using a thermal needle probe. The general trend of all analyzed parameters was as expected when dry

Simulated evolution of fractures and fracture networks subject to thermal cooling: A coupled discrete element and heat conduction model

Energy Technology Data Exchange (ETDEWEB)

Huang, Hai; Plummer, Mitchell; Podgorney, Robert

2013-02-01

Advancement of EGS requires improved prediction of fracture development and growth during reservoir stimulation and long-term operation. This, in turn, requires better understanding of the dynamics of the strongly coupled thermo-hydro-mechanical (THM) processes within fractured rocks. We have developed a physically based rock deformation and fracture propagation simulator by using a quasi-static discrete element model (DEM) to model mechanical rock deformation and fracture propagation induced by thermal stress and fluid pressure changes. We also developed a network model to simulate fluid flow and heat transport in both fractures and porous rock. In this paper, we describe results of simulations in which the DEM model and network flow & heat transport model are coupled together to provide realistic simulation of the changes of apertures and permeability of fractures and fracture networks induced by thermal cooling and fluid pressure changes within fractures. Various processes, such as Stokes flow in low velocity pores, convection-dominated heat transport in fractures, heat exchange between fluid-filled fractures and solid rock, heat conduction through low-permeability matrices and associated mechanical deformations are all incorporated into the coupled model. The effects of confining stresses, developing thermal stress and injection pressure on the permeability evolution of fracture and fracture networks are systematically investigated. Results are summarized in terms of implications for the development and evolution of fracture distribution during hydrofracturing and thermal stimulation for EGS.

How initial representations shape coupled learning processes

DEFF Research Database (Denmark)

Puranam, Phanish; Swamy, M.

2016-01-01

Coupled learning processes, in which specialists from different domains learn how to make interdependent choices among alternatives, are common in organizations. We explore the role played by initial representations held by the learners in coupled learning processes using a formal agent-based model....... We find that initial representations have important consequences for the success of the coupled learning process, particularly when communication is constrained and individual rates of learning are high. Under these conditions, initial representations that generate incorrect beliefs can outperform...... one that does not discriminate among alternatives, or even a mix of correct and incorrect representations among the learners. We draw implications for the design of coupled learning processes in organizations. © 2016 INFORMS....

Coupled thermo-hydro-mechanical analysis for the conceptual repository of high-level radioactive waste in China

International Nuclear Information System (INIS)

Lin, Y.M.; Wang, J.; Ke, D.; Cai, M.F.

2010-01-01

In order to safely dispose of the high-level radioactive waste (HLW), RD guide of HLW disposal was published in February 2006 in China. The spent fuel from nuclear power plants will be reprocessed first, followed by verification and final disposal. A conceptual repository 3D configuration comprises a single vertical borehole in a continuous and homogeneous hard rock, containing a canister surrounded by an over-pack and a bentonite layer, and the backfilled upper portion of the gallery using FLAC3D. To take into account in situ stress, geothermal gradient and groundwater of Beishan area, thermal relief of HLW and swelling pressure of buffer/backfill material made by GMZ01 bentonite, the TM, HM and THM evolution of the whole configuration is simulated over a period of 100 years. The results demonstrate that temperature is hardly affected by the couplings. In contrast, the influence of the couplings on the mechanical stresses is considerable. The repository has long-term stability in fully THM coupling action condition. (authors)

Monitoring and modelling of thermo-hydro-mechanical processes - main results of a heater experiment at the Mont Terri underground rock laboratory

Energy Technology Data Exchange (ETDEWEB)

Ingeborg, G.; Alheid, H.J. [BGR - Federal Institute for Geosciences and Natural Resources, Hannover (Germany); Jockwerz, N. [Gesellschaft fur Anlagen- und Reaktorsicherheit (GRS) - Final Repository Research Division, Braunschweig (Germany); Mayor, J.C. [ENRESA - Empresa Nacional des Residuos Radioactivos, Madrid (Spain); Garcia-Siner, J.L. [AITEMIN -Asociacion para la Investigacion y Desarrollo Industrial de los Recursos Naturales, Madrid, (Spain); Alonso, E. [CIMNE - Centre Internacional de Metodos Numerics en Ingenyeria, UPC, Barcelona (Spain); Weber, H.P. [NAGRA - National Cooperative for the Disposal of Radioactive Waste, Wettingen (Switzerland); Plotze, M. [ETHZ - Swiss Federal Institute of Technology Zurich, IGT, Zurich, (Switzerland); Klubertanz, G. [COLENCO Power Engineering Ltd., Baden (Switzerland)

2005-07-01

The long-term safety of permanent underground repositories relies on a combination of engineered and geological barriers, so that the interactions between the barriers in response to conditions expected in a high-level waste repository need to be identified and fully understood. Co-financed by the European Community, a heater experiment was realized on a pilot plant scale at the underground laboratory in Mont Terri, Switzerland. The experiment was accompanied by an extensive programme of continuous monitoring, experimental investigations on-site as well as in laboratories, and numerical modelling of the coupled thermo-hydro-mechanical processes. Heat-producing waste was simulated by a heater element of 10 cm diameter, held at a constant surface temperature of 100 C. The heater element (length 2 m) operated in a vertical borehole of 7 m depth at 4 to 6 m depth. It was embedded in a geotechnical barrier of pre-compacted bentonite blocks (outer diameter 30 cm) that were irrigated for 35 months before the heating phase (duration 18 months) began. The host rock is a highly consolidated stiff Jurassic clay stone (Opalinus Clay). After the heating phase, the vicinity of the heater element was explored by seismic, hydraulic, and geotechnical tests to investigate if the heating had induced changes in the Opalinus Clay. Additionally, rock mechanic specimens were tested in the laboratory. Finally, the experiment was dismantled to provide laboratory specimens of post - heating buffer and host rock material. The bentonite blocks were thoroughly wetted at the time of the dismantling. The volume increase amounted to 5 to 9% and was thus below the bentonite potential. Geo-electrical measurements showed no decrease of the water content in the vicinity of the heater during the heating phase. Decreasing energy input to the heater element over time suggests hence, that the bentonite dried leading to a decrease of its thermal conductivity. Gas release during the heating period occurred

Hydromechanical coupling in geologic processes

Science.gov (United States)

Neuzil, C.E.

2003-01-01

Earth's porous crust and the fluids within it are intimately linked through their mechanical effects on each other. This paper presents an overview of such "hydromechanical" coupling and examines current understanding of its role in geologic processes. An outline of the theory of hydromechanics and rheological models for geologic deformation is included to place various analytical approaches in proper context and to provide an introduction to this broad topic for nonspecialists. Effects of hydromechanical coupling are ubiquitous in geology, and can be local and short-lived or regional and very long-lived. Phenomena such as deposition and erosion, tectonism, seismicity, earth tides, and barometric loading produce strains that tend to alter fluid pressure. Resulting pressure perturbations can be dramatic, and many so-called "anomalous" pressures appear to have been created in this manner. The effects of fluid pressure on crustal mechanics are also profound. Geologic media deform and fail largely in response to effective stress, or total stress minus fluid pressure. As a result, fluid pressures control compaction, decompaction, and other types of deformation, as well as jointing, shear failure, and shear slippage, including events that generate earthquakes. By controlling deformation and failure, fluid pressures also regulate states of stress in the upper crust. Advances in the last 80 years, including theories of consolidation, transient groundwater flow, and poroelasticity, have been synthesized into a reasonably complete conceptual framework for understanding and describing hydromechanical coupling. Full coupling in two or three dimensions is described using force balance equations for deformation coupled with a mass conservation equation for fluid flow. Fully coupled analyses allow hypothesis testing and conceptual model development. However, rigorous application of full coupling is often difficult because (1) the rheological behavior of geologic media is complex

Multi-scale modelling and simulation of the thermo-hydro-mechanical behavior of concrete with explicit representation of cracking

International Nuclear Information System (INIS)

Tognevi, Amen

2012-01-01

The concrete structures of nuclear power plants can be subjected to moderate thermo-hydric loadings characterized by temperatures of the order of hundred of degrees in service conditions as well as in accidental ones. These loadings can be at the origin of important disorders, in particular cracking which accelerate hydric transfers in the structure. In the framework of the study of durability of these structures, a coupled thermo-hydro-mechanical model denoted THMs has been developed at Laboratoire d'Etude du Comportement des Betons et des Argiles (LECBA) of CEA Saclay in order to perform simulations of the concrete behavior submitted to such loadings. In this work, we focus on the improvement in the model THMs in one hand of the assessment of the mechanical and hydro-mechanical parameters of the unsaturated micro-cracked material and in the other hand of the description of cracking in terms of opening and propagation. The first part is devoted to the development of a model based on a multi-scale description of cement-based materials starting from the scale of the main hydrated products (portlandite, ettringite, C-S-H etc.) to the macroscopic scale of the cracked material. The investigated parameters are obtained at each scale of the description by applying analytical homogenization techniques. The second part concerns a fine numerical description of cracking. To this end, we choose to use combined finite element and discrete element methods. This procedure is presented and illustrated through a series of mechanical tests in order to show the feasibility of the method and to proceed to its validation. Finally, we apply the procedure to a heated wall and the proposed method for estimating the permeability shows the interest to take into account an anisotropic permeability tensor when dealing with mass transfers in cracked concrete structures. (author) [fr

Mont Terri Project - Heater experiment : rock and bentonite thermo-hydro-mechanical (THM) processes in the near field of a thermal source for development of deep underground high level radioactive waste repositories

Energy Technology Data Exchange (ETDEWEB)

Goebel, I.; Alheid, H.-J.; Kaufhold, St.; Naumann, M.; Pletsch, Th.; Plischke, I.; Schnier, H.; Schuster, K.; Sprado, K. [Bundesanstalt fuer Geowissenschaften und Rohstoffe (BGR), Hannover (Germany); Meyer, T.; Miehe, R.; Wieczorek, K. [Gesellschaft fuer Anlagen und Reaktorsicherheit mbH (GRS), Braunschweig (Germany); Mayor, J.C. [Empresa Nacional de Residuos Radioactivos SA (ENRESA), Madrid (Spain); Garcia-Sineriz, J.; Rey, M. [Asociacion para la Investigacion y Desarollo Industrial de los Recursos Naturales (AITEMIN), Madrid (Spain); Alonso, E.; Lloret, A.; Munoz, J.J. [Centre Internacional de Metodos Numerics en Ingenyeria (CIMNE), Barcelona (Spain); Weber, H. [National Cooperative for the Disposal of Radioactive Waste (Nagra), Wettingen (Switzerland); Ploetze, M. [Eidgenoessische Technische Hochschule Zuerich, Institut fuer Geotechnik, Zuerich (Switzerland); Klubertanz, G. [Colenco Power Engineering Ltd, Baden (Switzerland); Ammon, Ch. [Rothpletz Lienhard und Cie AG, Aarau (Switzerland); Graf, A.; Nussbaum, Ch.; Zingg, A. [Goetechnical Institute Ltd, Saint-Ursanne (Switzerland); Bossart, P. [Federal Office of Topography (swisstopo), Wabern (Switzerland); Buehler, Ch.; Kech, M.; Trick, Th. [Solexperts AG, Moenchaltorf (Switzerland); Emmerich, K. [ITC-WGT, Karlsruhe (Germany); Fernandez, A. M. [Ciemat, Madrid (Spain)

2007-07-01

The long-term safety of underground permanent repositories for radioactive waste relies on a combination of several engineered and geological barriers. The interactions between a host rock formation of the type 'Opalinus Clay' and an engineered barrier of the type 'bentonite buffer' are observed in the Heater Experiment (HE) during a hydration and a heating phase. The objective of the experiment is an improved understanding of the coupled thermo-hydro-mechanical (THM) processes in a host rock-buffer system achieved by experimental observations as well as numerical modelling. The basic objectives are in detail: a) Long-term monitoring in the vicinity of the heater during hydration and heating; especially observation and study of coupled THM processes in the near field, i.e. continuous measurements of temperatures, pore pressures, displacements, electric conductivity, and analysis of the gases and water released into the rock by effect of heating; b) Determination of the properties of barrier and host rock done mainly by laboratory and in situ experiments, i.e. general mechanical and mineralogical properties, mechanical state in-situ, and changes induced by the experiment; c) Study of the interaction between host rock and bentonite buffer as well as validation and refinement of existing tools for modelling THM processes; d) Study of the behaviour and reliability of instrumentation and measuring techniques, i.e. inspection of sensors after dismantling the experimental setting. To achieve the objectives, the experiment was accompanied by an extensive programme of continuous monitoring, experimental investigations on-site as well as in laboratories, and numerical modelling of the coupled THM processes. Finally, the experiment was dismantled to provide laboratory specimens of post-heating buffer and host rock material. The continuous monitoring of the experiment by a multitude of sensors (for temperature, pore pressure, total pressure, relative

Process-independent strong running coupling

International Nuclear Information System (INIS)

Binosi, Daniele; Mezrag, Cedric; Papavassiliou, Joannis; Roberts, Craig D.; Rodriguez-Quintero, Jose

2017-01-01

Here, we unify two widely different approaches to understanding the infrared behavior of quantum chromodynamics (QCD), one essentially phenomenological, based on data, and the other computational, realized via quantum field equations in the continuum theory. Using the latter, we explain and calculate a process-independent running-coupling for QCD, a new type of effective charge that is an analogue of the Gell-Mann–Low effective coupling in quantum electrodynamics. The result is almost identical to the process-dependent effective charge defined via the Bjorken sum rule, which provides one of the most basic constraints on our knowledge of nucleon spin structure. As a result, this reveals the Bjorken sum to be a near direct means by which to gain empirical insight into QCD's Gell-Mann–Low effective charge.

Coupled processes and the tropical climatology : part III : instabilities of the fully coupled climatology

NARCIS (Netherlands)

Dijkstra, H.A.; Neelin, J.D.

1998-01-01

Coupled processes between the equatorial ocean and atmosphere control the spatial structure of the annual mean state in the Pacific region,in particular the warm-pool/cold- tongue structure.At the same time,coupled processes are known to be responsible for the variability about this mean state,in

The Numerical Simulation of Coupling Behavior of Soil with Chemical Pollutant Effects

Science.gov (United States)

Liu, Z. J.; Li, X. K.; Tang, L. Q.

2010-05-01

The coupling behavior of clay plays a role in the integrity of clay barriers used in landfills. The clay barriers are subjected to mechanical and thermal effects coupled with hydraulic behavior, also, if the leachates become in contact with the clay liner, chemical effects may lead to some drastic changes in the properties of the clay. A numerical method to simulate the coupling behavior of soil with chemical pollutant effects is presented. Within the framework of Gens-Alonso model describing the constitutive behavior of unsaturated clay presented in reference[1], basing on the work of Wu[2] and Hueckel[3], a constitutive model describing the chemo-thermo-hydro-mechanical(CTHM) coupling behavior of clays in contact with a single organic contaminant is presented. The thermical softening and chemical softening is considered in the presented model. The strain arising in the material due to chemical and thermical effects can be decomposed into two parts: elastic expansion and plastic compaction. The chemical effects are described in terms of the mass concentration of the contaminant. The increases in temperature and contaminant concentration cause decreases of the pre-consolidation pressure and the cohesion. The mechanisms are called thermical softening and chemical softening. The presented coupled CTHM constitutive model has been integrated into the coupled thermo-hydro-mechanical mathematical model including contaminant transport in porous media. To solve the equilibrium equations, the grogram of finite element methods is developed with a stagger algorithm. The mechanisms taking place due to the coupling behaviour of the clay with a single contaminant solute are analysed with the presented numerical method.

Normal Mode Analysis to a Poroelastic Half-Space Problem under Generalized Thermoelasticity

Directory of Open Access Journals (Sweden)

Chunbao Xiong

Full Text Available Abstract The thermo-hydro-mechanical problems associated with a poroelastic half-space soil medium with variable properties under generalized thermoelasticity theory were investigated in this study. By remaining faithful to Biot’s theory of dynamic poroelasticity, we idealized the foundation material as a uniform, fully saturated, poroelastic half-space medium. We first subjected this medium to time harmonic loads consisting of normal or thermal loads, then investigated the differences between the coupled thermohydro-mechanical dynamic models and the thermo-elastic dynamic models. We used normal mode analysis to solve the resulting non-dimensional coupled equations, then investigated the effects that non-dimensional vertical displacement, excess pore water pressure, vertical stress, and temperature distribution exerted on the poroelastic half-space medium and represented them graphically.

Coupled processes in repository sealing

International Nuclear Information System (INIS)

Case, J.B.; Kelsall, P.C.

1985-01-01

The significance of coupled processes in repository sealing is evaluated. In most repository designs, shaft seals will be located in areas of relatively low temperature perturbation, in which case the coupling of temperature with stress and permeability may be less significant than the coupling between stress and permeability that occurs during excavation. Constitutive relationships between stress and permeability are reviewed for crystalline rock and rocksalt. These provide a basis for predicting the development of disturbed zones near excavations. Field case histories of the degree of disturbance are presented for two contrasting rock types - Stripa granite and Southeastern New Mexico rocksalt. The results of field investigations in both rock types confirm that hydraulic conductivity or permeability is stress dependent, and that shaft seal performance may be related to the degree that stresses are perturbed and restored near the seal

Abstraction of Drift-Scale Coupled Processes

International Nuclear Information System (INIS)

Francis, N.D.; Sassani, D.

2000-01-01

This Analysis/Model Report (AMR) describes an abstraction, for the performance assessment total system model, of the near-field host rock water chemistry and gas-phase composition. It also provides an abstracted process model analysis of potentially important differences in the thermal hydrologic (TH) variables used to describe the performance of a geologic repository obtained from models that include fully coupled reactive transport with thermal hydrology and those that include thermal hydrology alone. Specifically, the motivation of the process-level model comparison between fully coupled thermal-hydrologic-chemical (THC) and thermal-hydrologic-only (TH-only) is to provide the necessary justification as to why the in-drift thermodynamic environment and the near-field host rock percolation flux, the essential TH variables used to describe the performance of a geologic repository, can be obtained using a TH-only model and applied directly into a TSPA abstraction without recourse to a fully coupled reactive transport model. Abstraction as used in the context of this AMR refers to an extraction of essential data or information from the process-level model. The abstraction analysis reproduces and bounds the results of the underlying detailed process-level model. The primary purpose of this AMR is to abstract the results of the fully-coupled, THC model (CRWMS M andO 2000a) for effects on water and gas-phase composition adjacent to the drift wall (in the near-field host rock). It is assumed that drift wall fracture water and gas compositions may enter the emplacement drift before, during, and after the heating period. The heating period includes both the preclosure, in which the repository drifts are ventilated, and the postclosure periods, with backfill and drip shield emplacement at the time of repository closure. Although the preclosure period (50 years) is included in the process models, the postclosure performance assessment starts at the end of this initial period

Thermodynamically coupled mass transport processes in a saturated clay

International Nuclear Information System (INIS)

Carnahan, C.L.

1984-01-01

Gradients of temperature, pressure, and fluid composition in saturated clays give rise to coupled transport processes (thermal and chemical osmosis, thermal diffusion, ultrafiltration) in addition to the direct processes (advection and diffusion). One-dimension transport of water and a solute in a saturated clay subjected to mild gradients of temperature and pressure was simulated numerically. When full coupling was accounted for, volume flux (specific discharge) was controlled by thermal osmosis and chemical osmosis. The two coupled fluxes were oppositely directed, producing a point of stagnation within the clay column. Solute flows were dominated by diffusion, chemical osmosis, and thermal osmosis. Chemical osmosis produced a significant flux of solute directed against the gradient of solute concentration; this effect reduced solute concentrations relative to the case without coupling. Predictions of mass transport in clays at nuclear waste repositories could be significantly in error if coupled transport processes are not accounted for. 14 refs., 8 figs

Thermodynamically coupled mass transport processes in a saturated clay

International Nuclear Information System (INIS)

Carnahan, C.L.

1984-11-01

Gradients of temperature, pressure, and fluid composition in saturated clays give rise to coupled transport processes (thermal and chemical osmosis, thermal diffusion, ultrafiltration) in addition to the direct processes (advection and diffusion). One-dimensional transport of water and a solute in a saturated clay subjected to mild gradients of temperature and pressure was simulated numerically. When full coupling was accounted for, volume flux (specific discharge) was controlled by thermal osmosis and chemical osmosis. The two coupled fluxes were oppositely directed, producing a point of stagnation within the clay column. Solute flows were dominated by diffusion, chemical osmosis, and thermal osmosis. Chemical osmosis produced a significant flux of solute directed against the gradient of solute concentration; this effect reduced solute concentrations relative to the case without coupling. Predictions of mass transport in clays at nuclear waste repositories could be significantly in error if coupled transport processes are not accounted for. 14 references, 8 figures, 1 table

Fostering new relational experience: clinical process in couple psychotherapy.

Science.gov (United States)

Marmarosh, Cheri L

2014-03-01

One of the most critical goals for couple psychotherapy is to foster a new relational experience in the session where the couple feels safe enough to reveal more vulnerable emotions and to explore their defensive withdrawal, aggressive attacking, or blaming. The lived intimate experience in the session offers the couple an opportunity to gain integrative insight into their feelings, expectations, and behaviors that ultimately hinder intimacy. The clinical processes that are necessary include empathizing with the couple and facilitating safety within the session, looking for opportunities to explore emotions, ruptures, and unconscious motivations that maintain distance in the relationship, and creating a new relational experience in the session that has the potential to engender integrative insight. These clinical processes will be presented with empirical support. Experts from a session will be used to highlight how these processes influence the couple and promote increased intimacy. (PsycINFO Database Record (c) 2014 APA, all rights reserved).

Parallel coupling of symmetric and asymmetric exclusion processes

International Nuclear Information System (INIS)

Tsekouras, K; Kolomeisky, A B

2008-01-01

A system consisting of two parallel coupled channels where particles in one of them follow the rules of totally asymmetric exclusion processes (TASEP) and in another one move as in symmetric simple exclusion processes (SSEP) is investigated theoretically. Particles interact with each other via hard-core exclusion potential, and in the asymmetric channel they can only hop in one direction, while on the symmetric lattice particles jump in both directions with equal probabilities. Inter-channel transitions are also allowed at every site of both lattices. Stationary state properties of the system are solved exactly in the limit of strong couplings between the channels. It is shown that strong symmetric couplings between totally asymmetric and symmetric channels lead to an effective partially asymmetric simple exclusion process (PASEP) and properties of both channels become almost identical. However, strong asymmetric couplings between symmetric and asymmetric channels yield an effective TASEP with nonzero particle flux in the asymmetric channel and zero flux on the symmetric lattice. For intermediate strength of couplings between the lattices a vertical-cluster mean-field method is developed. This approximate approach treats exactly particle dynamics during the vertical transitions between the channels and it neglects the correlations along the channels. Our calculations show that in all cases there are three stationary phases defined by particle dynamics at entrances, at exits or in the bulk of the system, while phase boundaries depend on the strength and symmetry of couplings between the channels. Extensive Monte Carlo computer simulations strongly support our theoretical predictions. Theoretical calculations and computer simulations predict that inter-channel couplings have a strong effect on stationary properties. It is also argued that our results might be relevant for understanding multi-particle dynamics of motor proteins

Processivity and coupling in messenger RNA transcription.

Directory of Open Access Journals (Sweden)

Stuart Aitken

2010-01-01

Full Text Available The complexity of messenger RNA processing is now being uncovered by experimental techniques that are capable of detecting individual copies of mRNA in cells, and by quantitative real-time observations that reveal the kinetics. This processing is commonly modelled by permitting mRNA to be transcribed only when the promoter is in the on state. In this simple on/off model, the many processes involved in active transcription are represented by a single reaction. These processes include elongation, which has a minimum time for completion and processing that is not captured in the model.In this paper, we explore the impact on the mRNA distribution of representing the elongation process in more detail. Consideration of the mechanisms of elongation leads to two alternative models of the coupling between the elongating polymerase and the state of the promoter: Processivity allows polymerases to complete elongation irrespective of the promoter state, whereas coupling requires the promoter to be active to produce a full-length transcript. We demonstrate that these alternatives have a significant impact on the predicted distributions. Models are simulated by the Gillespie algorithm, and the third and fourth moments of the resulting distribution are computed in order to characterise the length of the tail, and sharpness of the peak. By this methodology, we show that the moments provide a concise summary of the distribution, showing statistically-significant differences across much of the feasible parameter range.We conclude that processivity is not fully consistent with the on/off model unless the probability of successfully completing elongation is low--as has been observed. The results also suggest that some form of coupling between the promoter and a rate-limiting step in transcription may explain the cell's inability to maintain high mRNA levels at low noise--a prediction of the on/off model that has no supporting evidence.

Dyadic Coping in Couple Therapy Process: An Exploratory Study.

Science.gov (United States)

Margola, Davide; Donato, Silvia; Accordini, Monica; Emery, Robert E; Snyder, Douglas K

2017-07-10

This study aimed at moving beyond previous research on couple therapy efficacy by examining moment-by-moment proximal couple and therapist interactions as well as final treatment outcomes and their reciprocal association. Seven hundred four episodes of dyadic coping within 56 early therapy sessions, taken from 28 married couples in treatment, were intensively analyzed and processed using a mixed-methods software (T-LAB). Results showed that negative dyadic coping was self-perpetuating, and therapists tended to passively observe the negative couple interaction; on the contrary, positive dyadic coping appeared to require a therapist's intervention to be maintained, and successful interventions mainly included information gathering as well as interpreting. Couples who dropped out of treatment were not actively engaged from the outset of therapy, and they used more negative dyadic coping, whereas couples who successfully completed treatment showed more positive dyadic coping very early in therapy. Results highlight the role of therapist action and control as critical to establishing rapport and credibility in couple therapy and suggest that dyadic coping patterns early in therapy may contribute to variable treatment response. © 2017 Family Process Institute.

Effects of coupled thermal, hydrological and chemical processes on nuclide transport

International Nuclear Information System (INIS)

Carnahan, C.L.

1987-03-01

Coupled thermal, hydrological and chemical processes can be classified in two categories. One category consists of the ''Onsager'' type of processes driven by gradients of thermodynamic state variables. These processes occur simultaneously with the direct transport processes. In particular, thermal osmosis, chemical osmosis and ultrafiltration may be prominent in semipermeable materials such as clays. The other category consists of processes affected indirectly by magnitudes of thermodynamic state variables. An important example of this category is the effect of temperature on rates of chemical reactions and chemical equilibria. Coupled processes in both categories may affect transport of radionuclides. Although computational models of limited extent have been constructed, there exists no model that accounts for the full set of THC-coupled processes. In the category of Onsager coupled processes, further model development and testing is severely constrained by a deficient data base of phenomenological coefficients. In the second category, the lack of a general description of effects of heterogeneous chemical reactions on permeability of porous media inhibits progress in quantitative modeling of hydrochemically coupled transport processes. Until fundamental data necessary for further model development have been acquired, validation efforts will be limited necessarily to testing of incomplete models of nuclide transport under closely controlled experimental conditions. 34 refs., 2 tabs

Rôles de la température et de la composition sur le couplage thermo-hydro-mécanique des bétons

OpenAIRE

Brue , Flore

2009-01-01

The French project of the storage of nuclear wastes, which is managed by the Andra, needs some experimental data on the durability of the concrete. Loadings which are taken into account are the desaturation/resaturation processes, the heat load and the mechanical evolution. Hence this study focuses on the coupling thermo-hydro-mechanical on concretes of the research program of Andra, made with CEM I and CEM V/A cement type. The water saturation degree and shrinkages of materials, which are su...

Thermally-driven Coupled THM Processes in Shales

Science.gov (United States)

Rutqvist, J.

2017-12-01

Temperature changes can trigger strongly coupled thermal-hydrological-mechanical (THM) processes in shales that are important to a number of subsurface energy applications, including geologic nuclear waste disposal and hydrocarbon extraction. These coupled processes include (1) direct pore-volume couplings, by thermal expansion of trapped pore-fluid that triggers instantaneous two-way couplings between pore fluid pressure and mechanical deformation, and (2) indirect couplings in terms of property changes, such as changes in mechanical stiffness, strength, and permeability. Direct pore-volume couplings have been studied in situ during borehole heating experiments in shale (or clay stone) formations at Mont Terri and Bure underground research laboratories in Switzerland and France. Typically, the temperature changes are accompanied with a rapid increase in pore pressure followed by a slower decrease towards initial (pre-heating) pore pressure. Coupled THM modeling of these heater tests shows that the pore pressure increases because the thermal expansion coefficient of the fluid is much higher than that of the porous clay stone. Such thermal pressurization induces fluid flow away from the pressurized area towards areas of lower pressure. The rate of pressure increase and magnitude of peak pressure depends on the rate of heating, pore-compressibility, and permeability of the shale. Modeling as well as laboratory experiments have shown that if the pore pressure increase is sufficiently large it could lead to fracturing of the shale or shear slip along pre-existing bedding planes. Another set of data and observations have been collected associated with studies related to concentrated heating and cooling of oil-shales and shale-gas formations. Heating may be used to enhance production from tight oil-shale, whereas thermal stimulation has been attempted for enhanced shale-gas extraction. Laboratory experiments on shale have shown that strength and elastic deformation

Synthesis report on thermally driven coupled processes

International Nuclear Information System (INIS)

Hardin, E.L.

1997-01-01

The main purpose of this report is to document observations and data on thermally coupled processes for conditions that are expected to occur within and around a repository at Yucca Mountain. Some attempt is made to summarize values of properties (e.g., thermal properties, hydrologic properties) that can be measured in the laboratory on intact samples of the rock matrix. Variation of these properties with temperature, or with conditions likely to be encountered at elevated temperature in the host rock, is of particular interest. However, the main emphasis of this report is on direct observation of thermally coupled processes at various scales. Direct phenomenological observations are vitally important in developing and testing conceptual models. If the mathematical implementation of a conceptual model predicts a consequence that is not observed, either (1) the parameters or the boundary conditions used in the calculation are incorrect or (2) the conceptual basis of the model does not fit the experiment; in either case, the model must be revised. For example, the effective continuum model that has been used in thermohydrology studies combines matrix and fracture flow in a way that is equivalent to an assumption that water is imbibed instantaneously from fractures into adjacent, partially saturated matrix. Based on this approximation, the continuum-flow response that is analogous to fracture flow will not occur until the effective continuum is almost completely saturated. This approximation is not entirely consistent with some of the experimental data presented in this report. This report documents laboratory work and field studies undertaken in FY96 and FY97 to investigate thermally coupled processes such as heat pipes and fracture-matrix coupling. In addition, relevant activities from past years, and work undertaken outside the Yucca Mountain project are summarized and discussed. Natural and artificial analogs are also discussed to provide a convenient source of

Thermohydromechanical stability analysis upon joint characteristics and depth variations in the region of an underground repository for the study of a disposal concept of high level radioactive wastes

International Nuclear Information System (INIS)

Kim, Jhin Wung; Bae, Dae Suk; Kang, Chul Hyung; Choi, Jong Won

2003-02-01

The objective of the present study is to understand a long term(500 years) thermohydromechanical interaction behavior in the vicinity of a repository cavern upon joint location and repository depth variations, and then, to contribute to the development of a disposal concept. The model includes a saturated rock mass, PWR spent fuels in a disposal canister surrounded by compacted bentonite inside a deposition hole, and mixed bentonite backfilled in the rest of the space within a cavern. It is assumed that two joint sets exist within a model. A joint set 1 includes 56 .deg. dip joints, 20m spaced, and a joint set 2 is in the direction perpendicular to a joint set 1 and includes 34 .deg. dip joints, 20m spaced. In order to understand the behavior change upon joint location variations, 5 different models of 500m depth are analyzed, and additional 3 different models of 1km depth are analyzed to understand the effect of a depth variation. The two dimensional distinct element code, UDEC is used for the analysis. To understand the joint behavior adjacent to a repository cavern, Barton-Bandis joint model is used. Effect of the decay heat for PWR spent fuels on a repository model is analyzed, and a steady state algorithm is used for a hydraulic analysis. According to the thermohydromechanical interaction behavior of a repository model upon variations of joint locations and a repository depth, during the period of 500 years from waste emplacement, the effect of a depth variation on the stress and displacement behavior of a model is comparatively smaller than the effect of decay heat from radioactive materials. From the study of the joint location variation effect, it is advisable not to locate an underground opening in the region very close to the joint crossings

Thermo-hydro-mechanical mode of canister retrieval test

International Nuclear Information System (INIS)

Zandarin, M.T.; Olivella, S.; Gens', A.; Alonso, E.E.

2010-01-01

Document available in extended abstract form only. The Canister Retrieval Tests (CRT) is a full scale in situ experiment performed by SKB at Aespoe Laboratory. The experiment involves placing a canister equipped with electrical heaters inside of a deposition hole bored in Aespoe diorite. The deposition hole is 8.55 metres deep and has a diameter of 1.76 metres. The space between canister and the hole is filled with a MX-80 bentonite buffer. The bentonite buffer was installed in form of blocks and rings of bentonite. At the top of the canister bentonite bricks occupy the volume between the canister top surface and the bottom surface of the plug. Due to the bentonite ring size there are two gaps; once between canister and buffer which was left empty and another one between buffer and rock that was filled with bentonite pellets. The top of the hole was sealed with a retaining plug composed of concrete and a steel plate. The plug was secured against heave caused by the swelling clay with nine cables anchored in the rock. An artificial pressurised saturation system was used because the supply of water from the rock was judged to be insufficient for saturating the buffer in a feasible time. A large number of instruments were installed to monitor the test as follows: - Canister - temperature and strain. - Rock mass - temperature and stress. - Retaining system - force and displacement. - Buffer - temperature, relative humidity, pore pressure and total pressure. After dismantling the tests the final dry density and water content of bentonite and pellets were measured. The comprehensive record of the Thermo-Hydro-Mechanical (THM) processes in the buffer give the possibility to investigate theoretical formulations and models, since the results of THM analyses can be checked against experimental data. As part of the European project THERESA, a 2-D axisymmetric model simulation of CRT bas been carried out. Some of the main objectives of this simulation are the study of the

Effect of the heating rate on residual thermo-hydro-mechanical properties of a high-strength concrete in the context of nuclear waste storage

International Nuclear Information System (INIS)

Galle, C.; Pin, M.; Ranc, G.; Rodrigues, S.

2003-01-01

Concrete is likely to be used in massive structures for nuclear waste long-term storage facilities in France. In the framework of vitrified waste and spent fuel management, these structures could be submitted to high temperatures. In standard conditions, ambient temperature should not exceed 60 degC but in case of failure of a cooling system, concretes could be temporarily exposed to temperatures up to 250 degC. Depending on the temperature rise kinetics, concretes could be damaged to a greater or lesser extent. In this context, an experimental study on the effect of heating rate on concrete thermo-hydro-mechanical properties exposed to high temperatures (110 - 250 degC) was carried out at the French Atomic Energy Commission (CEA). Data analysis and interpretation provided enough arguments to conclude that, at local scale, the impact of heating rate on residual properties was real though relatively limited. (author)

The construction of a model of the process of couples' forgiveness in emotion-focused therapy for couples.

Science.gov (United States)

Meneses, Catalina Woldarsky; Greenberg, Leslie S

2011-10-01

This study explored how forgiveness unfolds in the context of emotion-focused couples therapy (EFT-C) in eight cases of women betrayed by their partners. Forgiveness was defined as a process involving the reduction in negative feelings and the giving out of undeserved compassion. This was measured by changes in the pre- and posttreatment scores on the Enright Forgiveness Inventory, the Unfinished Business Resolution Scale, and a single item directly asking respondents to indicate their degree of forgiveness. A task analysis was performed to rigorously track the steps leading to forgiveness using videotapes of therapy sessions for eight couples. The performance of the four couples who forgave were compared with each other and then contrasted with the performance of another four couples who did not reach forgiveness at the end of therapy. Based on these observations, a model of the process of forgiveness in EFT-C and a process rating system were developed. © 2011 American Association for Marriage and Family Therapy.

Interaction of processes may explain induced seismicity after shut-in in Enhanced Geothermal Systems

Science.gov (United States)

De Simone, Silvia; Carrera, Jesus; Vilarrasa, Victor

2015-04-01

Deep fluid injection is a necessary operation in several engineering sectors, like geothermal energy production, natural gas storage, CO2 storage, etc. The seismicity associated to these activities has, in some occasions, reached unexpected magnitude, raising public concern. Moreover, the occurrence of such seismicity after the injection shut-in pointed out the incompleteness of the knowledge and the inability of fully managing these processes. On the other hand, the growing attention toward clean energy makes it clear that we cannot abandon these procedures, which have a huge potential. Therefore, deeply understanding the mechanisms that induce seismicity is crucial. In this study we consider hydraulic stimulation of deep geothermal systems and analyze the mechanisms that may induce or trigger seismicity. Given that the basic mechanism is fluid pressure increase, secondary triggering processes have been studied. In detail, we attempt to identify the potential mechanisms that may trigger seismicity in the post-injection phase, when the overpressure decreases. These mechanisms have been investigated with a coupled and uncoupled approach, in order to understand the individual effects of each one and the effects of the interactions between them on the reservoir stability. Besides fluid overpressure, another relevant process is the temperature variation. Indeed, in the case of enhanced geothermal systems, the temperature contrast between the injected cold fluid and the deep hot reservoir is great and induces thermal stress, which sensibly affects the in-situ stress field. Therefore, we have studied overpressure and temperature effects by means of analytic solutions and by means of hydro-mechanical and thermo-hydro-mechanical numerical simulations. Results show that in fractured rocks the spatial variability of hydraulic and mechanic parameters provokes no isotropic variation of the tensional field, in response to pressure and temperature perturbations. Another

Dissociative identity disorder and the process of couple therapy.

Science.gov (United States)

Macintosh, Heather B

2013-01-01

Couple therapy in the context of dissociative identity disorder (DID) has been neglected as an area of exploration and development in the couple therapy and trauma literature. What little discussion exists focuses primarily on couple therapy as an adjunct to individual therapy rather than as a primary treatment for couple distress and trauma. Couple therapy researchers have begun to develop adaptations to provide effective support to couples dealing with the impact of childhood trauma in their relationships, but little attention has been paid to the specific and complex needs of DID patients in couple therapy (H. B. MacIntosh & S. Johnson, 2008 ). This review and case presentation explores the case of "Lisa," a woman diagnosed with DID, and "Don," her partner, and illustrates the themes of learning to communicate, handling conflicting needs, responding to child alters, and addressing sexuality and education through their therapy process. It is the hope of the author that this discussion will renew interest in the field of couple therapy in the context of DID, with the eventual goal of developing an empirically testable model of treatment for couples.

A coupled thermo-hydro-mechanical-damage model for concrete subjected to moderate temperatures

Energy Technology Data Exchange (ETDEWEB)

Bary, B.; Carpentier, O. [CEA Saclay, DEN/DPC/SCCME/LECBA, F-91191 Gif Sur Yvette, (France); Ranc, G. [CEA VALRHO, DEN/DTEC/L2EC/LCEC, F-30207 Bagnols Sur Ceze, (France); Durand, S. [CEA Saclay, DEN/DM2S/SEMT/LM2S, F-91191 Gif Sur Yvette, (France)

2008-07-01

This study focuses on the concrete behavior subjected to moderate temperatures, with a particular emphasis on the transient thermo-hydric stage. A simplified coupled thermo-hydro-mechanical model is developed with the assumption that the gaseous phase is composed uniquely of vapor. Estimations of the mechanical parameters, Biot coefficient and permeability as a function of damage and saturation degree are provided by applying effective-medium approximation schemes. The isotherm adsorption curves are supposed to depend upon both temperature and crack-induced porosity. The effects of damage and parameters linked to transfer (in particular the adsorption curves) on the concrete structure response in the transient phase of heating are then investigated and evaluated. To this aim, the model is applied to the simulation of concrete cylinders with height and diameter of 0.80 m subjected to heating rates of 0.1 and 10 degrees C/min up to 160 degrees C. The numerical results are analyzed, commented and compared with experimental ones in terms of water mass loss, temperatures and gas pressures evolutions. A numerical study indicates that some parameters have a greater influence on the results than others, and that certain coupling terms in the mass conservation equation of water may be neglected. (authors)

The Experience of Couples in the Process of Treatment of Pathological Gambling: Couple vs. Individual Therapy

Science.gov (United States)

Tremblay, Joël; Dufour, Magali; Bertrand, Karine; Blanchette-Martin, Nadine; Ferland, Francine; Savard, Annie-Claude; Saint-Jacques, Marianne; Côté, Mélissa

2018-01-01

Context: Couple treatment for pathological gambling is an innovative strategy. There are some results supporting its potential effectiveness, but little is known about the subjective experiences of the participants. Objective: The aim of this article is to document the experiences of gamblers and their partners participating in one of two treatments, namely individual or couple. Method: In a study aiming to evaluate the efficacy of the Integrative Couple Treatment for Pathological Gambling (ICT-PG), couples who were entering specialized treatment for the addiction of one member who was a pathological gambler were randomly assigned to individual or ICT-PG. Nine months after their admission to treatment, gamblers and partners (n = 21 couples; n = 13 ICT-PG; n = 8 individual treatment) were interviewed in semi-structured interviews. A sequenced thematization method was used to extract the major themes. Results: This study highlighted five major themes in the therapeutic process noted by the gamblers and their partners mainly after the couple treatment but also partly through the individual therapy. These were: (1) the gamblers' anxiety about having to reveal their gambling problems in couple therapy; (2) the wish to develop a mutually beneficial understanding of gambling and its effects on the partners in the two types of treatments; (3) the transformation of negative attributions through a more effective intra-couple communication fostered by the couple therapy; (4) the partners' contribution to changes in gambling behavior and prevention of relapses, which were both better supported in couple therapy; and (5) the interpersonal nature of gambling and its connections with the couples' relationship. However, gamblers who were in individual treatment were more likely to mention that their partners' involvement was not necessary. Participants likewise made a few recommendations about the conditions underlying the choice of one treatment method or the other. Discussion

The Experience of Couples in the Process of Treatment of Pathological Gambling: Couple vs. Individual Therapy

Directory of Open Access Journals (Sweden)

Joël Tremblay

2018-01-01

Full Text Available Context: Couple treatment for pathological gambling is an innovative strategy. There are some results supporting its potential effectiveness, but little is known about the subjective experiences of the participants.Objective: The aim of this article is to document the experiences of gamblers and their partners participating in one of two treatments, namely individual or couple.Method: In a study aiming to evaluate the efficacy of the Integrative Couple Treatment for Pathological Gambling (ICT-PG, couples who were entering specialized treatment for the addiction of one member who was a pathological gambler were randomly assigned to individual or ICT-PG. Nine months after their admission to treatment, gamblers and partners (n = 21 couples; n = 13 ICT-PG; n = 8 individual treatment were interviewed in semi-structured interviews. A sequenced thematization method was used to extract the major themes.Results: This study highlighted five major themes in the therapeutic process noted by the gamblers and their partners mainly after the couple treatment but also partly through the individual therapy. These were: (1 the gamblers' anxiety about having to reveal their gambling problems in couple therapy; (2 the wish to develop a mutually beneficial understanding of gambling and its effects on the partners in the two types of treatments; (3 the transformation of negative attributions through a more effective intra-couple communication fostered by the couple therapy; (4 the partners' contribution to changes in gambling behavior and prevention of relapses, which were both better supported in couple therapy; and (5 the interpersonal nature of gambling and its connections with the couples' relationship. However, gamblers who were in individual treatment were more likely to mention that their partners' involvement was not necessary. Participants likewise made a few recommendations about the conditions underlying the choice of one treatment method or the other

Coupled processes in NRC high-level waste research

International Nuclear Information System (INIS)

Costanzi, F.A.

1987-01-01

The author discusses NRC research effort in support of evaluating license applications for disposal of nuclear waste and for promulgating regulations and issuing guidance documents on nuclear waste management. In order to do this they fund research activities at a number of laboratories, academic institutions, and commercial organizations. One of our research efforts is the coupled processes study. This paper discusses interest in coupled processes and describes the target areas of research efforts over the next few years. The specific research activities relate to the performance objectives of NRC's high-level waste (HLW) regulation and the U.S. Environmental Protection Agency (EPA) HLW standard. The general objective of the research program is to ensure the NRC has a sufficient independent technical base to make sound regulatory decisions

Understanding Coupled Earth-Surface Processes through Experiments and Models (Invited)

Science.gov (United States)

Overeem, I.; Kim, W.

2013-12-01

Traditionally, both numerical models and experiments have been purposefully designed to ';isolate' singular components or certain processes of a larger mountain to deep-ocean interconnected source-to-sink (S2S) transport system. Controlling factors driven by processes outside of the domain of immediate interest were treated and simplified as input or as boundary conditions. Increasingly, earth surface processes scientists appreciate feedbacks and explore these feedbacks with more dynamically coupled approaches to their experiments and models. Here, we discuss key concepts and recent advances made in coupled modeling and experimental setups. In addition, we emphasize challenges and new frontiers to coupled experiments. Experiments have highlighted the important role of self-organization; river and delta systems do not always need to be forced by external processes to change or develop characteristic morphologies. Similarly modeling f.e. has shown that intricate networks in tidal deltas are stable because of the interplay between river avulsions and the tidal current scouring with both processes being important to develop and maintain the dentritic networks. Both models and experiment have demonstrated that seemingly stable systems can be perturbed slightly and show dramatic responses. Source-to-sink models were developed for both the Fly River System in Papua New Guinea and the Waipaoa River in New Zealand. These models pointed to the importance of upstream-downstream effects and enforced our view of the S2S system as a signal transfer and dampening conveyor belt. Coupled modeling showed that deforestation had extreme effects on sediment fluxes draining from the catchment of the Waipaoa River in New Zealand, and that this increase in sediment production rapidly shifted the locus of offshore deposition. The challenge in designing coupled models and experiments is both technological as well as intellectual. Our community advances to make numerical model coupling more

Towards the generic conceptual and numerical framework for the simulation of CO 2 sequestration in different types of georeservoirs

DEFF Research Database (Denmark)

Görke, Uwe Jens; Taron, Joshua; Singh, Ashok

2011-01-01

In this paper, conceptual and numerical modeling of coupled thermo-hydro-mechanical (THM) processes during CO 2 injection and storage is presented. The commonly used averaging procedure combining the Theory of Mixtures and the Concept of Volume Fractions serves as background for the complex porous...... mathematical models are of similar structure. Thus, the paper is mainly focused on a generic theoretical framework for the coupled processes under consideration. Within this context, CO 2 sequestration in georeservoirs of different type can be simulated (e.g., saline aquifers, (nearly) depleted hydrocarbon...... media approach presented here. Numerical models are based on a generalized formulation of the individual and overall balance equations for mass and momentum, as well as, in non-isothermal case, the energy balance equation. Within the framework of a standard Galerkin approach, the method of weighted...

MOUNTAIN-SCALE COUPLED PROCESSES (TH/THC/THM) MODELS

International Nuclear Information System (INIS)

Y.S. Wu

2005-01-01

This report documents the development and validation of the mountain-scale thermal-hydrologic (TH), thermal-hydrologic-chemical (THC), and thermal-hydrologic-mechanical (THM) models. These models provide technical support for screening of features, events, and processes (FEPs) related to the effects of coupled TH/THC/THM processes on mountain-scale unsaturated zone (UZ) and saturated zone (SZ) flow at Yucca Mountain, Nevada (BSC 2005 [DIRS 174842], Section 2.1.1.1). The purpose and validation criteria for these models are specified in ''Technical Work Plan for: Near-Field Environment and Transport: Coupled Processes (Mountain-Scale TH/THC/THM, Drift-Scale THC Seepage, and Drift-Scale Abstraction) Model Report Integration'' (BSC 2005 [DIRS 174842]). Model results are used to support exclusion of certain FEPs from the total system performance assessment for the license application (TSPA-LA) model on the basis of low consequence, consistent with the requirements of 10 CFR 63.342 [DIRS 173273]. Outputs from this report are not direct feeds to the TSPA-LA. All the FEPs related to the effects of coupled TH/THC/THM processes on mountain-scale UZ and SZ flow are discussed in Sections 6 and 7 of this report. The mountain-scale coupled TH/THC/THM processes models numerically simulate the impact of nuclear waste heat release on the natural hydrogeological system, including a representation of heat-driven processes occurring in the far field. The mountain-scale TH simulations provide predictions for thermally affected liquid saturation, gas- and liquid-phase fluxes, and water and rock temperature (together called the flow fields). The main focus of the TH model is to predict the changes in water flux driven by evaporation/condensation processes, and drainage between drifts. The TH model captures mountain-scale three-dimensional flow effects, including lateral diversion and mountain-scale flow patterns. The mountain-scale THC model evaluates TH effects on water and gas

MOUNTAIN-SCALE COUPLED PROCESSES (TH/THC/THM)MODELS

Energy Technology Data Exchange (ETDEWEB)

Y.S. Wu

2005-08-24

This report documents the development and validation of the mountain-scale thermal-hydrologic (TH), thermal-hydrologic-chemical (THC), and thermal-hydrologic-mechanical (THM) models. These models provide technical support for screening of features, events, and processes (FEPs) related to the effects of coupled TH/THC/THM processes on mountain-scale unsaturated zone (UZ) and saturated zone (SZ) flow at Yucca Mountain, Nevada (BSC 2005 [DIRS 174842], Section 2.1.1.1). The purpose and validation criteria for these models are specified in ''Technical Work Plan for: Near-Field Environment and Transport: Coupled Processes (Mountain-Scale TH/THC/THM, Drift-Scale THC Seepage, and Drift-Scale Abstraction) Model Report Integration'' (BSC 2005 [DIRS 174842]). Model results are used to support exclusion of certain FEPs from the total system performance assessment for the license application (TSPA-LA) model on the basis of low consequence, consistent with the requirements of 10 CFR 63.342 [DIRS 173273]. Outputs from this report are not direct feeds to the TSPA-LA. All the FEPs related to the effects of coupled TH/THC/THM processes on mountain-scale UZ and SZ flow are discussed in Sections 6 and 7 of this report. The mountain-scale coupled TH/THC/THM processes models numerically simulate the impact of nuclear waste heat release on the natural hydrogeological system, including a representation of heat-driven processes occurring in the far field. The mountain-scale TH simulations provide predictions for thermally affected liquid saturation, gas- and liquid-phase fluxes, and water and rock temperature (together called the flow fields). The main focus of the TH model is to predict the changes in water flux driven by evaporation/condensation processes, and drainage between drifts. The TH model captures mountain-scale three-dimensional flow effects, including lateral diversion and mountain-scale flow patterns. The mountain-scale THC model evaluates TH effects on

FEBEX Full-Scalle Engineered barriers experiment in crystalline host rock Preoperational thermo-hydro-mechanical (THM) modelling of the in situ test

International Nuclear Information System (INIS)

1998-01-01

This report contains the results of a set of 1-D and 2-D coupled thermo-hydro-mechanical (THM) analyses carried out during the preoperational stage simulating the in situ FEBEX test. The analyses incorporate available information concerning rock and bentonite properties as well as the final test layout and conditions. The main goals are: -To provide the best estimate of test performance given current models and information - To define a basis for future model improvements. The theoretical bases of the analyses and the computer code used are reviewed. Special reference is made to the process of parameter estimation that tries to incorporate available information on material behaviour obtained in the characterisation work carried out both in the laboratory and in the field. Data obtained in the characterisation stage is also used to define initial and boundary conditions. The results of the 1-D THM Base Case analysis are used to gain a good understanding of expected test behaviour concerning thermal, hydraulic and mechanical problems. A quite extensive programme of sensitivity analyses is also reported in which the effect of a number of parameters and boundary conditions are examined. The results of the sensitivity analyses place an appropriate context the information obtained from the Base Case showing, for instance, that rock desaturation and degree of buffer hydration depend on some critical parameters in a complex way. Two-dimensional effects are discussed on the basis of the results of 2-D axisymmetric THM analysis performed using a longitudinal section that provides a better representation of real test geometry. Quantitative but not qualitative differences are found with respect to the 1-D results. Finally, a 2-D THM cross section analysis has been performed under plane strain conditions. No specific 2-D effects are observed in this case as quasi-axisymmetric conditions have been prescribed. The models employed in the analyses included in this report have not

Gene regulation and noise reduction by coupling of stochastic processes

Science.gov (United States)

Ramos, Alexandre F.; Hornos, José Eduardo M.; Reinitz, John

2015-02-01

Here we characterize the low-noise regime of a stochastic model for a negative self-regulating binary gene. The model has two stochastic variables, the protein number and the state of the gene. Each state of the gene behaves as a protein source governed by a Poisson process. The coupling between the two gene states depends on protein number. This fact has a very important implication: There exist protein production regimes characterized by sub-Poissonian noise because of negative covariance between the two stochastic variables of the model. Hence the protein numbers obey a probability distribution that has a peak that is sharper than those of the two coupled Poisson processes that are combined to produce it. Biochemically, the noise reduction in protein number occurs when the switching of the genetic state is more rapid than protein synthesis or degradation. We consider the chemical reaction rates necessary for Poisson and sub-Poisson processes in prokaryotes and eucaryotes. Our results suggest that the coupling of multiple stochastic processes in a negative covariance regime might be a widespread mechanism for noise reduction.

Gene regulation and noise reduction by coupling of stochastic processes.

Science.gov (United States)

Ramos, Alexandre F; Hornos, José Eduardo M; Reinitz, John

2015-02-01

Here we characterize the low-noise regime of a stochastic model for a negative self-regulating binary gene. The model has two stochastic variables, the protein number and the state of the gene. Each state of the gene behaves as a protein source governed by a Poisson process. The coupling between the two gene states depends on protein number. This fact has a very important implication: There exist protein production regimes characterized by sub-Poissonian noise because of negative covariance between the two stochastic variables of the model. Hence the protein numbers obey a probability distribution that has a peak that is sharper than those of the two coupled Poisson processes that are combined to produce it. Biochemically, the noise reduction in protein number occurs when the switching of the genetic state is more rapid than protein synthesis or degradation. We consider the chemical reaction rates necessary for Poisson and sub-Poisson processes in prokaryotes and eucaryotes. Our results suggest that the coupling of multiple stochastic processes in a negative covariance regime might be a widespread mechanism for noise reduction.

Coupled processes in single fractures, double fractures and fractured porous media

International Nuclear Information System (INIS)

Tsang, C.F.

1986-12-01

The emplacement of a nuclear waste repository in a fractured porous medium provides a heat source of large dimensions over an extended period of time. It also creates a large cavity in the rock mass, changing significantly the stress field. Such major changes induce various coupled thermohydraulic, hydromechanic and hydrochemical transport processes in the environment around a nuclear waste repository. The present paper gives, first, a general overview of the coupled processes involving thermal, mechanical, hydrological and chemical effects. Then investigations of a number of specific coupled processes are described in the context of fluid flow and transport in a single fracture, two intersecting fractures and a fractured porous medium near a nuclear waste repository. The results are presented and discussed

Client Discourses on the Process of Seeking Same-Sex Couple Counselling

Science.gov (United States)

Grove, Jan; Peel, Elizabeth; Owen-Pugh, Valerie

2013-01-01

How same-sex couples manage the process of seeking help for their relationships is an under-researched area. Twelve semi-structured interviews were conducted with 16 people who had engaged in same-sex couple counselling, and were analysed using discourse analysis. The ways in which the couples positioned themselves as part of a "minority…

3-D Modelling of Electromagnetic, Thermal, Mechanical and Metallurgical Couplings in Metal Forming Processes

International Nuclear Information System (INIS)

Chenot, Jean-Loup; Bay, Francois

2007-01-01

The different stages of metal forming processes often involve - beyond the mechanical deformations processes - other physical coupled problems, such as heat transfer, electromagnetism or metallurgy. The purpose of this paper is to focus on problems involving electromagnetic couplings. After a brief recall on electromagnetic modeling, we shall then focus on induction heating processes and present some results regarding heat transfer, as well as mechanical couplings. A case showing coupling for metallurgic microstructure evolution will conclude this paper

On a morphological approach of the meso-structure for the multi-scale analysis of the thermo-hydro-mechanical behaviour of cementitious materials

International Nuclear Information System (INIS)

Le, T.T.H.

2011-01-01

The investigation of the behavior of heated concrete is a major research topic which concerns the assessment of safety level of structures when exposed to high temperatures, for instance during a fire. For this purpose, several modeling approaches were developed within thermo-hydro-mechanical (THM) frameworks in order to take into account the involved physic-chemical and mechanical processes that affect stability of heated concrete. However, existing models often do note account explicitly for the heterogeneity of the material: concrete is composite material that may be schematized as an assembly of inclusions (aggregates) embedded in a cementitious matrix (cement paste). This latter may be described as a partially saturated open porous medium. The aggregates are characterized by their mineralogical nature together with their morphology and size distribution. The material heterogeneity bring an additional complexity: the need to take into account the microstructure in order to quantify the effect of matrix-inclusion thermal, hygral and mechanical incompatibilities on the THM behavior of concrete. This work is a first step in this direction. For this purpose, a three-dimensional (3D) multi-scale finite element model is developed. It allows affecting specific behaviors to matrix and inclusions. For the former, where mass transports occur within the connected porous network, a three-fluids approach (liquid water, vapor and dry air) is adopted and is coupled to a poro-mechanical damage based approach. For inclusions (aggregates) no hygral component arises a pure thermo-mechanical model is considered. The developed model is then used to investigate, either by 2D or 3D numerical simulations, effects of mineralogical nature, morphology and distribution of aggregates. Studied effects have mainly concerned the influence of these parameters on local fluctuations of simulated temperature, gas pressure and damage fields with regard to experimentally observed dispersion. The

Thermo-Hydro-Mechanical Characterisation of the Bentonite of a Simulated HLW Repository after Five Years Operation ( In Situ Test of the FEBEX Project)

Energy Technology Data Exchange (ETDEWEB)

Villar, M. V.

2004-07-01

After five years of operation, heater 1 of the FEBEX experimental at the Grimsel Test Sites was switched off in February 2002. Following cooling of the system, the bentonite barrier was dismantled and the heater extracted. During dismantling many bentonite samples were taken. Several determinations were carried out in these samples with the aim of: (1) characterise the actual state of the bentonite and (2) determine the possible changes in its properties occurred during the experiment. The results of the thermo-hydro-mechanical characterisation performed at CIEMAT are reported and analysed. The distribution of water content and dry density of the bentonite in vertical sections presents axial symmetry. The construction gaps of the barrier have been filled by the expansion of the bentonite. The water retention capacity, the hydraulic conductivity and the swelling capacity of the samples from Grimsel have not irreversible changed. The pre consolidation pressure of the Grimsel samples has decreased due to the microstructural changes associated to the volume increase experienced during hydration. The thermal conductivity is higher for the bentonite blocks of the external ring of the barrier. (Author)

Thermo-Hydro-Mechanical Characterisation of the Bentonite of a Simulated HLW Repository after Five Years Operation ( In Situ Test of the FEBEX Project)

International Nuclear Information System (INIS)

Villar, M. V.

2004-01-01

After five years of operation, heater 1 of the FEBEX experimental at the Grimsel Test Sites was switched off in February 2002. Following cooling of the system, the bentonite barrier was dismantled and the heater extracted. During dismantling many bentonite samples were taken. Several determinations were carried out in these samples with the aim of: (1) characterise the actual state of the bentonite and (2) determine the possible changes in its properties occurred during the experiment. The results of the thermo-hydro-mechanical characterisation performed at CIEMAT are reported and analysed. The distribution of water content and dry density of the bentonite in vertical sections presents axial symmetry. The construction gaps of the barrier have been filled by the expansion of the bentonite. The water retention capaciaty, the hydraulic conductivity and the swelling capacity of the samples from Grimsel have not irreversible changed. The preconsolidation pressure of the Grimsel samples has decreased due to the microstructural changes asswociated to the volume increase experienced during hydration. The thermal conductivity is higher for the bentonite blocks of the external ring of the barrier. (Author)

A Thermo-Hydro-Mechanical coupled Numerical modeling of Injection-induced seismicity on a pre-existing fault

Science.gov (United States)

Kim, Jongchan; Archer, Rosalind

2017-04-01

In terms of energy development (oil, gas and geothermal field) and environmental improvement (carbon dioxide sequestration), fluid injection into subsurface has been dramatically increased. As a side effect of these operations, a number of injection-induced seismic activities have also significantly risen. It is known that the main causes of induced seismicity are changes in local shear and normal stresses and pore pressure as well. This mechanism leads to increase in the probability of earthquake occurrence on permeable pre-existing fault zones predominantly. In this 2D fully coupled THM geothermal reservoir numerical simulation of injection-induced seismicity, we investigate the thermal, hydraulic and mechanical behavior of the fracture zone, considering a variety of 1) fault permeability, 2) injection rate and 3) injection temperature to identify major contributing parameters to induced seismic activity. We also calculate spatiotemporal variation of the Coulomb stress which is a combination of shear stress, normal stress and pore pressure and lastly forecast the seismicity rate on the fault zone by computing the seismic prediction model of Dieterich (1994).

Simulation of Stochastic Processes by Coupled ODE-PDE

Science.gov (United States)

Zak, Michail

2008-01-01

A document discusses the emergence of randomness in solutions of coupled, fully deterministic ODE-PDE (ordinary differential equations-partial differential equations) due to failure of the Lipschitz condition as a new phenomenon. It is possible to exploit the special properties of ordinary differential equations (represented by an arbitrarily chosen, dynamical system) coupled with the corresponding Liouville equations (used to describe the evolution of initial uncertainties in terms of joint probability distribution) in order to simulate stochastic processes with the proscribed probability distributions. The important advantage of the proposed approach is that the simulation does not require a random-number generator.

Development of a numerical code for the prediction of the long-term behavior of the underground facilities for the high-level radioactive waste disposal

International Nuclear Information System (INIS)

Sawada, Masataka; Okada, Tetsuji; Hasegawa, Takuma

2006-01-01

Complicated phenomena originated by thermo-hydro-mechanical coupling behavior will occur in the near-field of geological disposal of nuclear waste. Development of a numerical evaluation method for such phenomena is important in order to make a reasonable repository design and a safety assessment. In order to achieve the objective above, a numerical model using the equations which can evaluate the swelling characteristics of buffer materials based on the diffusive double layer theory is proposed, and a numerical scheme for the thermo-hydro-mechanical coupled analysis including the swelling model is constructed. The proposed swelling model can reproduce the behavior observed during both swelling pressure tests and swelling deformation tests. When the developed numerical code is applied to the laboratory heater test using a bentonite specimen, it can reproduce the thermal gradient, the distribution of saturation rate and the variation of porosity. The developed numerical code will be applied to well-controlled laboratory tests and full-scale in-situ tests in the future work. In order to apply to the various geochemical conditions around the engineered barrier, chemical component will be coupled to the present numerical code. (author)

Global land-atmosphere coupling associated with cold climate processes

OpenAIRE

Dutra, Emanuel, 1983-

2011-01-01

Tese de doutoramento, Ciências Geofísicas e da Geoinformação (Meteorologia), Universidade de Lisboa, Faculdade de Ciências, 2011 This dissertation constitutes an assessment of the role of cold processes, associated with snow cover, in controlling the land-atmosphere coupling. The work was based on model simulations, including offline simulations with the land surface model HTESSEL, and coupled atmosphere simulations with the EC-EARTH climate model. A revised snow scheme was developed and t...

An adaptive deep-coupled GNSS/INS navigation system with hybrid pre-filter processing

Science.gov (United States)

Wu, Mouyan; Ding, Jicheng; Zhao, Lin; Kang, Yingyao; Luo, Zhibin

2018-02-01

The deep-coupling of a global navigation satellite system (GNSS) with an inertial navigation system (INS) can provide accurate and reliable navigation information. There are several kinds of deeply-coupled structures. These can be divided mainly into coherent and non-coherent pre-filter based structures, which have their own strong advantages and disadvantages, especially in accuracy and robustness. In this paper, the existing pre-filters of the deeply-coupled structures are analyzed and modified to improve them firstly. Then, an adaptive GNSS/INS deeply-coupled algorithm with hybrid pre-filters processing is proposed to combine the advantages of coherent and non-coherent structures. An adaptive hysteresis controller is designed to implement the hybrid pre-filters processing strategy. The simulation and vehicle test results show that the adaptive deeply-coupled algorithm with hybrid pre-filters processing can effectively improve navigation accuracy and robustness, especially in a GNSS-challenged environment.

Panel discussion on near-field coupled processes with emphasis on performance assessment

International Nuclear Information System (INIS)

Codell, R.B.; Baca, R.G.; Ahola, M.P.

1996-01-01

The presentations in this panel discussion involve the general topic of near-field coupled processes and postclosure performance assessment with an emphasis on rock mechanics. The potential impact of near-field rock mass deformation on repository performance was discussed, as well as topics including long term excavation deterioration, the performance of geologic seals, and coupled processes concerning rock mechanics in performance assessments

A weighted coupling metric for business process models

NARCIS (Netherlands)

Vanderfeesten, I.T.P.; Cardoso, J.; Reijers, H.A.; Eder, J.; Tomassen, S.L.; Opdahl, A.; Sindre, G.

2007-01-01

Various efforts recently aimed at the development of quality metrics for process models. In this paper, we propose a new notion of coupling, which has been used successfully in software engineering for many years. It extends other work by specifically incorporating the effects of different types of

Ultrafast spin exchange-coupling torque via photo-excited charge-transfer processes

Science.gov (United States)

Ma, X.; Fang, F.; Li, Q.; Zhu, J.; Yang, Y.; Wu, Y. Z.; Zhao, H. B.; Lüpke, G.

2015-10-01

Optical control of spin is of central importance in the research of ultrafast spintronic devices utilizing spin dynamics at short time scales. Recently developed optical approaches such as ultrafast demagnetization, spin-transfer and spin-orbit torques open new pathways to manipulate spin through its interaction with photon, orbit, charge or phonon. However, these processes are limited by either the long thermal recovery time or the low-temperature requirement. Here we experimentally demonstrate ultrafast coherent spin precession via optical charge-transfer processes in the exchange-coupled Fe/CoO system at room temperature. The efficiency of spin precession excitation is significantly higher and the recovery time of the exchange-coupling torque is much shorter than for the demagnetization procedure, which is desirable for fast switching. The exchange coupling is a key issue in spin valves and tunnelling junctions, and hence our findings will help promote the development of exchange-coupled device concepts for ultrafast coherent spin manipulation.

Long term thermo-hydro-mechanical interaction behavior study of the saturated, discontinuous granitic rock mass around the radwaste repository using a steady state flow algorithm

Energy Technology Data Exchange (ETDEWEB)

Kim, Jhin Wung; Bae, Dae Suk; Kang, Chul Hyung; Choi, Jong Won [Korea Atomic Energy Research Institute, Taejeon (Korea)

2002-02-01

The objective of the present study is to understand the long term (500 years) thermo-hydro-mechanical interaction behavior of the 500 m depth underground radwaste repository in the saturated, discontinuous granitic rock mass using a steady state flow algorithm. The numerical model includes a saturated granitic rock mass with joints around the repository and a 45 .deg. C fault passing through the tunnel roof-wall intersection, and a canister with PWR spent fuels surrounded by the compacted bentonite and mixed-bentonite. Barton-Bandis joint constitutive model from the UDEC code is used for the joints. For the hydraulic analysis, a steady state flow algorithm is used for the groundwater flow through the rock joints. For the thermal analysis, heat transfer is modeled as isotropic conduction and heat decays exponentially with time. The results show that the variations of the hydraulic aperture, hydraulic conductivity, normal stress, normal displacements, and shear displacements of the joints are high in the vicinity of the repository and stay fairly constant on the region away from the repository. 14 refs., 15 figs., 11 tabs. (Author)

Differences in Pornography Use Among Couples: Associations with Satisfaction, Stability, and Relationship Processes.

Science.gov (United States)

Willoughby, Brian J; Carroll, Jason S; Busby, Dean M; Brown, Cameron C

2016-01-01

The present study utilized a sample of 1755 adult couples in heterosexual romantic relationships to examine how different patterns of pornography use between romantic partners may be associated with relationship outcomes. While pornography use has been generally associated with some negative and some positive couple outcomes, no study has yet explored how differences between partners may uniquely be associated with relationship well-being. Results suggested that greater discrepancies between partners in pornography use were related to less relationship satisfaction, less stability, less positive communication, and more relational aggression. Mediation analyses suggested that greater pornography use discrepancies were primarily associated with elevated levels of male relational aggression, lower female sexual desire, and less positive communication for both partners which then predicted lower relational satisfaction and stability for both partners. Results generally suggest that discrepancies in pornography use at the couple level are related to negative couple outcomes. Specifically, pornography differences may alter specific couple interaction processes which, in turn, may influence relationship satisfaction and stability. Implications for scholars and clinicians interested in how pornography use is associated with couple process are discussed.

Drift-Scale Coupled Processes (DST and THC Seepage) Models

Energy Technology Data Exchange (ETDEWEB)

E. Gonnenthal; N. Spyoher

2001-02-05

The purpose of this Analysis/Model Report (AMR) is to document the Near-Field Environment (NFE) and Unsaturated Zone (UZ) models used to evaluate the potential effects of coupled thermal-hydrologic-chemical (THC) processes on unsaturated zone flow and transport. This is in accordance with the ''Technical Work Plan (TWP) for Unsaturated Zone Flow and Transport Process Model Report'', Addendum D, Attachment D-4 (Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M and O) 2000 [153447]) and ''Technical Work Plan for Nearfield Environment Thermal Analyses and Testing'' (CRWMS M and O 2000 [153309]). These models include the Drift Scale Test (DST) THC Model and several THC seepage models. These models provide the framework to evaluate THC coupled processes at the drift scale, predict flow and transport behavior for specified thermal loading conditions, and predict the chemistry of waters and gases entering potential waste-emplacement drifts. The intended use of this AMR is to provide input for the following: (1) Performance Assessment (PA); (2) Abstraction of Drift-Scale Coupled Processes AMR (ANL-NBS-HS-000029); (3) UZ Flow and Transport Process Model Report (PMR); and (4) Near-Field Environment (NFE) PMR. The work scope for this activity is presented in the TWPs cited above, and summarized as follows: continue development of the repository drift-scale THC seepage model used in support of the TSPA in-drift geochemical model; incorporate heterogeneous fracture property realizations; study sensitivity of results to changes in input data and mineral assemblage; validate the DST model by comparison with field data; perform simulations to predict mineral dissolution and precipitation and their effects on fracture properties and chemistry of water (but not flow rates) that may seep into drifts; submit modeling results to the TDMS and document the models. The model development, input data

Drift-Scale Coupled Processes (DST and THC Seepage) Models

International Nuclear Information System (INIS)

Sonnenthale, E.

2001-01-01

The purpose of this Analysis/Model Report (AMR) is to document the Near-Field Environment (NFE) and Unsaturated Zone (UZ) models used to evaluate the potential effects of coupled thermal-hydrologic-chemical (THC) processes on unsaturated zone flow and transport. This is in accordance with the ''Technical Work Plan (TWP) for Unsaturated Zone Flow and Transport Process Model Report'', Addendum D, Attachment D-4 (Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M and O) 2000 [1534471]) and ''Technical Work Plan for Nearfield Environment Thermal Analyses and Testing'' (CRWMS M and O 2000 [153309]). These models include the Drift Scale Test (DST) THC Model and several THC seepage models. These models provide the framework to evaluate THC coupled processes at the drift scale, predict flow and transport behavior for specified thermal loading conditions, and predict the chemistry of waters and gases entering potential waste-emplacement drifts. The intended use of this AMR is to provide input for the following: Performance Assessment (PA); Near-Field Environment (NFE) PMR; Abstraction of Drift-Scale Coupled Processes AMR (ANL-NBS-HS-000029); and UZ Flow and Transport Process Model Report (PMR). The work scope for this activity is presented in the TWPs cited above, and summarized as follows: Continue development of the repository drift-scale THC seepage model used in support of the TSPA in-drift geochemical model; incorporate heterogeneous fracture property realizations; study sensitivity of results to changes in input data and mineral assemblage; validate the DST model by comparison with field data; perform simulations to predict mineral dissolution and precipitation and their effects on fracture properties and chemistry of water (but not flow rates) that may seep into drifts; submit modeling results to the TDMS and document the models. The model development, input data, sensitivity and validation studies described in this AMR are

Coupling of snow and permafrost processes using the Basic Modeling Interface (BMI)

Science.gov (United States)

Wang, K.; Overeem, I.; Jafarov, E. E.; Piper, M.; Stewart, S.; Clow, G. D.; Schaefer, K. M.

2017-12-01

We developed a permafrost modeling tool based by implementing the Kudryavtsev empirical permafrost active layer depth model (the so-called "Ku" component). The model is specifically set up to have a basic model interface (BMI), which enhances the potential coupling to other earth surface processes model components. This model is accessible through the Web Modeling Tool in Community Surface Dynamics Modeling System (CSDMS). The Kudryavtsev model has been applied for entire Alaska to model permafrost distribution at high spatial resolution and model predictions have been verified by Circumpolar Active Layer Monitoring (CALM) in-situ observations. The Ku component uses monthly meteorological forcing, including air temperature, snow depth, and snow density, and predicts active layer thickness (ALT) and temperature on the top of permafrost (TTOP), which are important factors in snow-hydrological processes. BMI provides an easy approach to couple the models with each other. Here, we provide a case of coupling the Ku component to snow process components, including the Snow-Degree-Day (SDD) method and Snow-Energy-Balance (SEB) method, which are existing components in the hydrological model TOPOFLOW. The work flow is (1) get variables from meteorology component, set the values to snow process component, and advance the snow process component, (2) get variables from meteorology and snow component, provide these to the Ku component and advance, (3) get variables from snow process component, set the values to meteorology component, and advance the meteorology component. The next phase is to couple the permafrost component with fully BMI-compliant TOPOFLOW hydrological model, which could provide a useful tool to investigate the permafrost hydrological effect.

Modeling of thermodynamic properties of refrigerant/absorbent couples using data mining process

International Nuclear Information System (INIS)

Sencan, Arzu

2007-01-01

In this paper, in order to determine thermodynamic properties of two alternative refrigerant/absorbent couples (methanol/LiBr and methanol/LiCl), a data mining process was used. These fluid couples can be used in absorption heat pump systems, and their main advantage is that they do not cause ozone depletion. In order to train the network, limited experimental measurements were used as training and test data. In the present study, linear regression (LR), pace regression (PR), sequential minimal optimization (SMO), M5 model tree, M5'Rules and back propagation neural network (BPNN) models are applied within the data mining process for determining the specific volume of the methanol/LiBr and methanol/LiCl fluid couples. The best result was obtained by using the back propagation model. A new formulation is presented for determination of the specific volumes of the two refrigerant/absorbent couples. The use of this new formulation, which can be employed with any programming language or spreadsheet program for estimation of the specific volumes of fluid couples, as described in this paper, may make the use of dedicated BPNN software unnecessary

Reactive transport modeling of coupled inorganic and organic processes in groundwater

Energy Technology Data Exchange (ETDEWEB)

Brun, Adam

1997-12-31

The main goals of this project are to develop and apply a reactive transport code for simulation of coupled organic and inorganic processes in the pollution plume in the ground water down-gradient from the Vejen landfill, Denmark. The detailed field investigations in this aquifer have previously revealed a complex pattern of strongly interdependent organic and inorganic processes. These processes occur simultaneously in a flow and transport system where the mixing of reactive species is influenced by the rather complex geology in the vicinity of the landfill. The removal of organic matter is influenced by the presence of various electron acceptors that also are involved in various inorganic geochemical reactions. It was concluded from the investigations that degradation of organic matter, complexation, mineral precipitation and dissolution, ion-exchange and inorganic redox reactions, as a minimum, should be included in the formulation of the model. The coupling of the organic and inorganic processes is developed based on a literature study. All inorganic processes are as an approximation described as equilibriumm processes. The organic processes are described by a maximum degradation rate that is decreased according to the availability of the participants in the processes, the actual pH, and the presence of inhibiting species. The reactive transport code consists of three separate codes, a flow and transport code, a geochemical code, and a biodegradation code. An iterative solution scheme couples the three codes. The coupled code was successfully verified for simple problems for which analytical solutions exist. For more complex problems the code was tested on synthetic cases and expected plume behavior was successfully simulated. Application of the code to the Vejen landfill aquifer was successful to the degree that the redox zonation down-gradient from the landfill was simulated correctly and that several of the simulated plumes showed a reasonable agreement with

[A new strategy for Chinese medicine processing technologies: coupled with individuation processed and cybernetics].

Science.gov (United States)

Zhang, Ding-kun; Yang, Ming; Han, Xue; Lin, Jun-zhi; Wang, Jia-bo; Xiao, Xiao-he

2015-08-01

The stable and controllable quality of decoction pieces is an important factor to ensure the efficacy of clinical medicine. Considering the dilemma that the existing standardization of processing mode cannot effectively eliminate the variability of quality raw ingredients, and ensure the stability between different batches, we first propose a new strategy for Chinese medicine processing technologies that coupled with individuation processed and cybernetics. In order to explain this thinking, an individual study case about different grades aconite is provided. We hope this strategy could better serve for clinical medicine, and promote the inheritance and innovation of Chinese medicine processing skills and theories.

Advances in the study of far-field phenomena affecting repository performance

International Nuclear Information System (INIS)

Tsang, C.F.

1991-01-01

Studies of far-field phenomena affecting repository performance have focussed on the role of fractures and other heterogeneities in the potential transport of radioactive solutes from the repository to the biosphere. The present paper summarizes two recent advances in the subject: the channeling model for the understanding and analysis tracer transport in variable-aperture fractures and the modeling of coupled thermo-hydro-mechanical processes in geologic formation around a repository. The paper concludes with remarks on the need for duality in the approach to performance assessment. One line of the duality is fundamental studies and the other, goal-oriented assessment to satisfy regulatory requirements. 15 refs., 10 figs., 1 tab

FEBEX II Project Final report on thermo-hydro-mechanical laboratory tests

International Nuclear Information System (INIS)

Lloret, A.; Romero, E.; Villar, M. V.

2004-01-01

The results of the thermo-hydro-mechanical (THM) study of the FEBEX bentonite performed during FEBEX II are presented. The laboratory test program continued in part with the works carried out during FEBEX I, particularly in activities related to tests aimed to the calibration of the models, the acquisition of parameters by back-analysis and the improvement of the knowledge on the behaviour of expansive clays. But the program has also included tests on new areas: investigations about the influence of the microstructure changes in bentonite, of temperature and of the solute concentration on the behaviour of clay. Besides, several tests were proposed in order to understand the unexpected behaviour observed in the mock-up test, towards the end of year 2. Temperature effects on water retention curves in confined and unconfined conditions were determined, and swelling pressure, hydraulic conductivity and swelling and consolidation strains as a function of temperature were successfully measured. Different experimental techniques and equipments were developed to study thermal induced changes under partially saturated states, covering a wide range of suctions. FEBEX bentonite remains suitable as a sealing material in HLW repositories (from the hydro- mechanical point of view) for temperatures of up to 80 C, as it keeps its high water retention capacity, low permeability and self-healing ability. The extrapolation of results points out to the preservation of properties for at least up to 100 C. Mercury intrusion porosimetry and environmental scanning electron microscopy provided promising results in order to characterise the bentonite microstructure and to give information about the mechanisms influencing pore size distribution changes on high active clays. The use of digital imaging techniques allowed verifying that at micro-scale level, where chemical phenomena prevail, strains are almost reversible as it is considered in the two-level elasto-plastic models. The swelling

FEBEX II Project Final report on thermo-hydro-mechanical laboratory tests

Energy Technology Data Exchange (ETDEWEB)

Lloret, A.; Romero, E.; Villar, M. V.

2004-07-01

The results of the thermo-hydro-mechanical (THM) study of the FEBEX bentonite performed during FEBEX II are presented. The laboratory test program continued in part with the works carried out during FEBEX I, particularly in activities related to tests aimed to the calibration of the models, the acquisition of parameters by back-analysis and the improvement of the knowledge on the behaviour of expansive clays. But the program has also included tests on new areas: investigations about the influence of the microstructure changes in bentonite, of temperature and of the solute concentration on the behaviour of clay. Besides, several tests were proposed in order to understand the unexpected behaviour observed in the mock-up test, towards the end of year 2. Temperature effects on water retention curves in confined and unconfined conditions were determined, and swelling pressure, hydraulic conductivity and swelling and consolidation strains as a function of temperature were successfully measured. Different experimental techniques and equipments were developed to study thermal induced changes under partially saturated states, covering a wide range of suctions. FEBEX bentonite remains suitable as a sealing material in HLW repositories (from the hydro- mechanical point of view) for temperatures of up to 80 C, as it keeps its high water retention capacity, low permeability and self-healing ability. The extrapolation of results points out to the preservation of properties for at least up to 100 C. Mercury intrusion porosimetry and environmental scanning electron microscopy provided promising results in order to characterise the bentonite microstructure and to give information about the mechanisms influencing pore size distribution changes on high active clays. The use of digital imaging techniques allowed verifying that at micro-scale level, where chemical phenomena prevail, strains are almost reversible as it is considered in the two-level elasto-plastic models. The swelling

Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures

International Nuclear Information System (INIS)

Rutqvist, Jonny; Blanco-Martin, Laura; Molins, Sergi; Trebotich, David; Birkholzer, Jens

2015-01-01

In this report, we present FY2015 progress by Lawrence Berkeley National Laboratory (LBNL) related to modeling of coupled thermal-hydrological-mechanical-chemical (THMC) processes in salt and their effect on brine migration at high temperatures. This is a combined milestone report related to milestone Salt R&D Milestone ''Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures'' (M3FT-15LB0818012) and the Salt Field Testing Milestone (M3FT-15LB0819022) to support the overall objectives of the salt field test planning.

Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures

Energy Technology Data Exchange (ETDEWEB)

Rutqvist, Jonny [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Blanco-Martin, Laura [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Molins, Sergi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Trebotich, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Birkholzer, Jens [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2015-09-01

In this report, we present FY2015 progress by Lawrence Berkeley National Laboratory (LBNL) related to modeling of coupled thermal-hydrological-mechanical-chemical (THMC) processes in salt and their effect on brine migration at high temperatures. This is a combined milestone report related to milestone Salt R&D Milestone “Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures” (M3FT-15LB0818012) and the Salt Field Testing Milestone (M3FT-15LB0819022) to support the overall objectives of the salt field test planning.

Mountain-Scale Coupled Processes (TH/THC/THM)

International Nuclear Information System (INIS)

Dixon, P.

2004-01-01

The purpose of this Model Report is to document the development of the Mountain-Scale Thermal-Hydrological (TH), Thermal-Hydrological-Chemical (THC), and Thermal-Hydrological-Mechanical (THM) Models and evaluate the effects of coupled TH/THC/THM processes on mountain-scale UZ flow at Yucca Mountain, Nevada. This Model Report was planned in ''Technical Work Plan (TWP) for: Performance Assessment Unsaturated Zone'' (BSC 2002 [160819], Section 1.12.7), and was developed in accordance with AP-SIII.10Q, Models. In this Model Report, any reference to ''repository'' means the nuclear waste repository at Yucca Mountain, and any reference to ''drifts'' means the emplacement drifts at the repository horizon. This Model Report provides the necessary framework to test conceptual hypotheses for analyzing mountain-scale hydrological/chemical/mechanical changes and predict flow behavior in response to heat release by radioactive decay from the nuclear waste repository at the Yucca Mountain site. The mountain-scale coupled TH/THC/THM processes models numerically simulate the impact of nuclear waste heat release on the natural hydrogeological system, including a representation of heat-driven processes occurring in the far field. The TH simulations provide predictions for thermally affected liquid saturation, gas- and liquid-phase fluxes, and water and rock temperature (together called the flow fields). The main focus of the TH Model is to predict the changes in water flux driven by evaporation/condensation processes, and drainage between drifts. The TH Model captures mountain-scale three dimensional (3-D) flow effects, including lateral diversion at the PTn/TSw interface and mountain-scale flow patterns. The Mountain-Scale THC Model evaluates TH effects on water and gas chemistry, mineral dissolution/precipitation, and the resulting impact to UZ hydrological properties, flow and transport. The THM Model addresses changes in permeability due to mechanical and thermal disturbances in

Electric currents couple spatially separated biogeochemical processes in marine sediment

DEFF Research Database (Denmark)

Nielsen, Lars Peter; Risgaard-Petersen, Nils; Fossing, Henrik

2010-01-01

Some bacteria are capable of extracellular electron transfer, thereby enabling them to use electron acceptors and donors without direct cell contact 1, 2, 3, 4 . Beyond the micrometre scale, however, no firm evidence has previously existed that spatially segregated biogeochemical processes can...... be coupled by electric currents in nature. Here we provide evidence that electric currents running through defaunated sediment couple oxygen consumption at the sediment surface to oxidation of hydrogen sulphide and organic carbon deep within the sediment. Altering the oxygen concentration in the sea water...... in the sediment was driven by electrons conducted from the anoxic zone. A distinct pH peak in the oxic zone could be explained by electrochemical oxygen reduction, but not by any conventional sets of aerobic sediment processes. We suggest that the electric current was conducted by bacterial nanowires combined...

H, HM, and THM-C processes in natural barriers

Energy Technology Data Exchange (ETDEWEB)

Javeri, V.; Le, T.T.; Cui, Y.J.; Delage, P.; Li, X.J.; Wieczorek, K.; Jockwer, N.; Romero, E.; Lima, A.; Gens, A.; Li, X.L.; Francois, B.; Nuth, M.; Laloui, L.; Chen, W.; Jia, S.; Yu, H.; Wu, G.; Li, X.; Bernier, F.; Tan, X.; Wu, G.; Jia, S.; Giot, R.; Hoxha, D.; Giraud, A.; Homand, F.; Su, K.; Chavant, C.; Duveau, G.; Jia, Y.; Shao, J.F.; Peron, H.; Laloui, L.; Hueckel, T.; Hu, L.B.; Auvray, C.; Lequiller, B.; Cuisinier, O.; Ferber, V.; Cui, Y.J.; Deneele, D.; Uhlig, L.; Jobmann, M.; Polster, M.; Vaunat, J.; Garrite, B.; Wileveau, Y.; Sato, H.; Jacinto, A.; Sanchez, M.; Ledesma, A.; Morel, J.; Balland, C.; Armand, G.; Nguyen Minh, D.; Vales, F.; Pham, Q.T.; Gharbi, H.; Mokni, N.; Olivella, S.; Li, X.; Smets, St.; Valcke, E.; Karnland, O.; Nilsson, U.; Olsson, S.; Sellin, P.; Fernandez, A.M.; Melon, A.M.; Villar, M.V.; Turrero, M.J.; Garitte, B.; Guimaraes, L.D.N.; Gens, A.; Mayor, J.C.; Koliji, A.; Laloui, L.; Vulliet, L.; Hamdi, N.; Marzouki, A.; Srasra, E.; Cuss, R.J.; Harrington, J.F.; Noy, D.J.; Birchall, D.J.; Marschall, P.; Mallet, A.; Ababou, R.; Matray, J.M.; Renaud, V.; Maison, T.; Enachescu, C.; Frieg, B.; Rohs, St.; Paris, B.; Robinet, J.C.; Bui, T.D.; Barnichon, J.D.; Plas, F.; Klubertanz, G.; Folly, M.; Hufschmied, P.; Frank, E

2007-07-01

This session gathers 30 articles (posters) dealing with: the three Dimensional analyses of combined gas, heat and nuclide transport in a repository considering coupled thermo-hydro geomechanical processes; the experimental study on the thermo-hydro-mechanical behaviour of boom clay; hydraulic in-situ measurements in the Opalinus clay in the frame of a heater test performed at the Mont Terri URL; the hydro-mechanical behaviour of natural boom clay in controlled-suction tests; a constitutive approach to address the thermal and hydric impacts in the concept of deep radioactive waste repositories; the numerical analysis on stability of boom clay tunnel by shield construction; a thermo-hydro-mechanical model for clay in unsaturated conditions; the 3D modelling of TER experiment accounting for fully anisotropic thermo-poro-elastic behaviour; the hydro-mechanical modeling of shaft excavation in Meuse/Haute-Marne laboratory; the modelling of drying damage in engineered and natural clay barriers for nuclear waste disposal; the elasto-viscoplastic behaviour of Meuse/Haute-Marne argillite: laboratory tests and modelling; the long-term behaviour of a lime treated soil under percolation conditions; the stress redistribution and hydro-mechanical effects due to excavation and drilling operations in TER experiment; a thermodynamic model on swelling of bentonite buffer and backfill materials; the 3D analysis of a heating test in the Opalinus clay; the THM analysis of a 'mock-up' laboratory experiment using a double-structure expansive model; the measurement of the effect of re-confinement on rock properties around a slot; a laboratory Study of desaturation - re-saturation effects on a clay-stone; the deformation induced by dissolution of salts in porous media; the bentonite swelling pressure in pure water and saline solutions; the mineralogy and sealing properties of various bentonites and smectite-rich clay materials; the evaluation of the geochemical processes occurring

Drift-Scale Coupled Processes (DST and THC Seepage) Models

International Nuclear Information System (INIS)

Dixon, P.

2004-01-01

The purpose of this Model Report (REV02) is to document the unsaturated zone (UZ) models used to evaluate the potential effects of coupled thermal-hydrological-chemical (THC) processes on UZ flow and transport. This Model Report has been developed in accordance with the ''Technical Work Plan for: Performance Assessment Unsaturated Zone'' (Bechtel SAIC Company, LLC (BSC) 2002 [160819]). The technical work plan (TWP) describes planning information pertaining to the technical scope, content, and management of this Model Report in Section 1.12, Work Package AUZM08, ''Coupled Effects on Flow and Seepage''. The plan for validation of the models documented in this Model Report is given in Attachment I, Model Validation Plans, Section I-3-4, of the TWP. Except for variations in acceptance criteria (Section 4.2), there were no deviations from this TWP. This report was developed in accordance with AP-SIII.10Q, ''Models''. This Model Report documents the THC Seepage Model and the Drift Scale Test (DST) THC Model. The THC Seepage Model is a drift-scale process model for predicting the composition of gas and water that could enter waste emplacement drifts and the effects of mineral alteration on flow in rocks surrounding drifts. The DST THC model is a drift-scale process model relying on the same conceptual model and much of the same input data (i.e., physical, hydrological, thermodynamic, and kinetic) as the THC Seepage Model. The DST THC Model is the primary method for validating the THC Seepage Model. The DST THC Model compares predicted water and gas compositions, as well as mineral alteration patterns, with observed data from the DST. These models provide the framework to evaluate THC coupled processes at the drift scale, predict flow and transport behavior for specified thermal-loading conditions, and predict the evolution of mineral alteration and fluid chemistry around potential waste emplacement drifts. The DST THC Model is used solely for the validation of the THC

The Coupling between Gamma and Theta Oscillation and Visuotactile Integration Process

Directory of Open Access Journals (Sweden)

Noriaki Kanayama

2011-10-01

Full Text Available Some researches revealed the relationship between multisensory integration and EEG oscillations. Previous studies revealed that the visuotactile integration process could be explained by gamma and theta band oscillation. In addition, recent studies have showed the possibility that a coupling between oscillations at the different frequency bands plays an important role on the multisensory integration system. This study aimed to investigate whether the gamma and theta oscillations show the coupling during the visuotactile integration. Using congruency effect paradigm only for left hand, we measured scalp EEG during simultaneous presentation of “spatially congruent” or “spatially incongruent” visuotactile stimuli. In Experiment 1, the proportion of the spatially congruent trials (80% vs 20% was changed across the experimental blocks. The results showed that the relationship between gamma power and theta phase at the parietal area was modulated by the proportion. In Experiment 2, the saliency of the vibration stimulus (0dB vs −20dB was changed across trials. The results showed that the relationship between gamma power and theta phase was immune to the saliency. These results suggest that multisensory integration process has a plasticity, which is modulated by the proportion of congruent trial, and the process could be explained by the coupling between gamma/theta oscillations.

Report on Modeling Coupled Processes in the Near Field of a Clay Repository

Energy Technology Data Exchange (ETDEWEB)

Liu, Hui -Hai [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Houseworth, Jim [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Rutqvist, Jonny [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Li, Lianchong [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Asahina, Daisuke [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Chen, Fei [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Birkholzer, Jens [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-08-01

Clay/shale has been considered as potential host rock for geological disposal of high-level radioactive waste throughout the world. Coupled thermal, hydrological, mechanical, and chemical (THMC) processes have a significant impact on the long-term safety of a clay repository. For example, the excavation damaged zone (EDZ) near repository tunnels can modify local permeability (resulting from induced fractures), potentially leading to less confinement capability. This report documents results from three R&D activities: (1) implementation and validation of constitutive relationships, (2) development of a discrete fracture network (DFN) model for investigating coupled processes in the EDZ, and (3) development of a THM model for the FE tests at Mont Terri, Switzerland, for the purpose of model validation. The overall objective of these activities is to provide an improved understanding of EDZ evolution in clay repositories and the associated coupled processes, and to develop advanced relevant modeling capabilities.

Seawater desalination plant using nuclear heating reactor coupled with MED process

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

A small size plant for seawater desalination using nuclear heating reactor coupled with MED process was developed by the Institute of Nuclear Energy Technology, Tsinghua University, China. This seawater desalination plant was designed to supply potable water demand to some coastal location or island where both fresh water and energy source are severely lacking. It is also recommended as a demonstration and training facility for seawater desalination using nuclear energy. The design of small size of seawater desalination plant couples two proven technologies: Nuclear Heating Reactor (NHR) and Multi-Effect Destination (MED) process. The NHR design possesses intrinsic and passive safety features, which was demonstrated by the experiences of the project NHR-5. The intermediate circuit and steam circuit were designed as the safety barriers between the NHR reactor and MED desalination system. Within 10～200 MWt of the power range of the heating reactor, the desalination plant could provide 8000 to 150,000 m3/d of high quality potable water. The design concept and parameters, safety features and coupling scheme are presented.

Seawater desalination plant using nuclear heating reactor coupled with MED process

International Nuclear Information System (INIS)

Wu Shaorong; Dong Duo; Zhang Dafang; Wang Xiuzhen

2000-01-01

A small size plant for seawater desalination using nuclear heating reactor coupled with MED process was developed by the Institute of Nuclear Energy Technology, Tsinghua University, China. this seawater desalination plant was designed to supply potable water demand to some coastal location or island where both fresh water and energy source are severely lacking. It is also recommended as a demonstration and training facility for seawater desalination using nuclear energy. The design of small size of seawater desalination plant couples two proven technologies: Nuclear Heating Reactor (NHR) and Multi-Effect Destination (MED) process. The NHR design possesses intrinsic and passive safety features, which was demonstrated by the experiences of the project NHR-5. the intermediate circuit and steam circuit were designed as the safety barriers between the NHR reactor and MED desalination system. Within 10-200 MWt of the power range of the heating reactor, the desalination plant could provide 8000 to 150,000 m 3 /d of high quality potable water. The design concept and parameters, safety features and coupling scheme are presented

Study of the water retention and the consolidation of partially saturated soils in a thermo-hydro-mechanical framework

International Nuclear Information System (INIS)

Salager, Simon

2007-01-01

This work is concerned with the study of water retention and consolidation of unsaturated soils in a thermo-hydro-mechanical framework. It is organized into two parts which deal respectively with deformation and temperature effects on hydric behaviour, and suction and temperature effects on mechanical behaviour. In the first part, we point out the relevance of the characteristic surface concept for soils as opposed to the retention curve, which has limited modelling power in the case of deformable media. The characteristic surface concept is experimentally illustrated for the example of a clayey silty sand. Its modelling is based on a large sample of experimental investigations with about 240 measurements of the triplet void ratio, water content, suction. In addition, a thermo-hydric behaviour model is proposed in order to determine the characteristic surface and the retention curve for a given temperature. This model is validated for the case of two materials: a ceramic and a clayey silty sand through direct testing, and for other materials on the basis of an analysis of the literature. Finally, we present an application to the determination of the permeability of unsaturated soils taking into account deformation and temperature. In the second part, temperature and suction effects on the mechanical behaviour are studied through consolidation tests on 'Sion' silt. These tests are performed for different temperatures and suctions. For each test, swelling and compression indexes, as well as the pre-consolidation pressure are measured. The influence of temperature and suction on these essential parameters of mechanical behaviour is determined. Finally, we propose a theoretical model which account for pre-consolidation pressure as a function of temperature and suction. (author)

A THM stress-strain framework for modelling the performance of argillaceous materials in deep repositories for radioactive waste

International Nuclear Information System (INIS)

Laloui, L.; Francois, B.

2007-01-01

In the scenarios for deep, geological nuclear-waste repositories, clayey soils will be hydrated, heated, cooled and dried. The numerical modelling of these mechanical processes is a key issue. Performance assessment of deep repositories for heat-generating radioactive waste would benefit from improvements in mechanical stress-strain constitutive modelling of the coupled thermo-hydro-mechanical behaviour. The presented framework allows progress in understanding the most involved phenomena relevant to nuclear-waste repositories and their coupled nature. It could be used both in the design and in the performance assessment of repositories. It may be applied to disposal in clay formations and to hard-rock repositories where artificially compacted clay is to be used as buffer and backfill. Such a constitutive framework may help in understanding some unexplained or controversial behaviours and in defining experimental programmes to answer key questions. (author)

Modeling Coupled Processes in Clay Formations for Radioactive Waste Disposal

Energy Technology Data Exchange (ETDEWEB)

Liu, Hui-Hai; Rutqvist, Jonny; Zheng, Liange; Sonnenthal, Eric; Houseworth, Jim; Birkholzer, Jens

2010-08-31

As a result of the termination of the Yucca Mountain Project, the United States Department of Energy (DOE) has started to explore various alternative avenues for the disposition of used nuclear fuel and nuclear waste. The overall scope of the investigation includes temporary storage, transportation issues, permanent disposal, various nuclear fuel types, processing alternatives, and resulting waste streams. Although geologic disposal is not the only alternative, it is still the leading candidate for permanent disposal. The realm of geologic disposal also offers a range of geologic environments that may be considered, among those clay shale formations. Figure 1-1 presents the distribution of clay/shale formations within the USA. Clay rock/shale has been considered as potential host rock for geological disposal of high-level nuclear waste throughout the world, because of its low permeability, low diffusion coefficient, high retention capacity for radionuclides, and capability to self-seal fractures induced by tunnel excavation. For example, Callovo-Oxfordian argillites at the Bure site, France (Fouche et al., 2004), Toarcian argillites at the Tournemire site, France (Patriarche et al., 2004), Opalinus clay at the Mont Terri site, Switzerland (Meier et al., 2000), and Boom clay at Mol site, Belgium (Barnichon et al., 2005) have all been under intensive scientific investigations (at both field and laboratory scales) for understanding a variety of rock properties and their relations with flow and transport processes associated with geological disposal of nuclear waste. Clay/shale formations may be generally classified as indurated and plastic clays (Tsang et al., 2005). The latter (including Boom clay) is a softer material without high cohesion; its deformation is dominantly plastic. For both clay rocks, coupled thermal, hydrological, mechanical and chemical (THMC) processes are expected to have a significant impact on the long-term safety of a clay repository. For

Modeling Coupled Processes in Clay Formations for Radioactive Waste Disposal

International Nuclear Information System (INIS)

Liu, Hui-Hai; Rutqvist, Jonny; Zheng, Liange; Sonnenthal, Eric; Houseworth, Jim; Birkholzer, Jens

2010-01-01

As a result of the termination of the Yucca Mountain Project, the United States Department of Energy (DOE) has started to explore various alternative avenues for the disposition of used nuclear fuel and nuclear waste. The overall scope of the investigation includes temporary storage, transportation issues, permanent disposal, various nuclear fuel types, processing alternatives, and resulting waste streams. Although geologic disposal is not the only alternative, it is still the leading candidate for permanent disposal. The realm of geologic disposal also offers a range of geologic environments that may be considered, among those clay shale formations. Figure 1-1 presents the distribution of clay/shale formations within the USA. Clay rock/shale has been considered as potential host rock for geological disposal of high-level nuclear waste throughout the world, because of its low permeability, low diffusion coefficient, high retention capacity for radionuclides, and capability to self-seal fractures induced by tunnel excavation. For example, Callovo-Oxfordian argillites at the Bure site, France (Fouche et al., 2004), Toarcian argillites at the Tournemire site, France (Patriarche et al., 2004), Opalinus clay at the Mont Terri site, Switzerland (Meier et al., 2000), and Boom clay at Mol site, Belgium (Barnichon et al., 2005) have all been under intensive scientific investigations (at both field and laboratory scales) for understanding a variety of rock properties and their relations with flow and transport processes associated with geological disposal of nuclear waste. Clay/shale formations may be generally classified as indurated and plastic clays (Tsang et al., 2005). The latter (including Boom clay) is a softer material without high cohesion; its deformation is dominantly plastic. For both clay rocks, coupled thermal, hydrological, mechanical and chemical (THMC) processes are expected to have a significant impact on the long-term safety of a clay repository. For

A novel integrated thermally coupled moving bed reactors for naphtha reforming process with hydrodealkylation of toluene

International Nuclear Information System (INIS)

Iranshahi, Davood; Saeedi, Reza; Azizi, Kolsoom; Nategh, Mahshid

2017-01-01

Highlights: • A novel thermally coupled reactor in CCR naphtha reforming process is modeled. • The required heat of Naphtha process is attained with toluene hydrodealkylation. • A new kinetic model involving 32 pseudo-component and 84 reactions is proposed. • The aromatics and hydrogen production increase 19% and 23%, respectively. - Abstract: Due to the importance of catalytic naphtha reforming process in refineries, development of this process to attain the highest yield of desired products is crucial. In this study, continuous catalyst regeneration naphtha reforming process with radial flow is coupled with hydrodealkylation of toluene to prevent energy loss while enhancing aromatics and hydrogen yields. In this coupled process, heat is transferred between hot and cold sections (from hydrodealkylation of toluene to catalytic naphtha reforming process) using the process integration method. A steady-state two-dimensional model, which considers coke formation on the catalyst pellets, is developed and 32 pseudo-components with 84 reactions are investigated. Kinetic model utilized for HDA process is homogeneous and non-catalytic. The modeling results reveal an approximate increase of 19% and 23% in aromatics and hydrogen molar flow rates, respectively, in comparison with conventional naphtha reforming process. The improvement in aromatics production evidently indicates that HDA is a suitable process to be coupled with naphtha reforming.

Efficient production of acetone-butanol-ethanol (ABE) from cassava by a fermentation-pervaporation coupled process.

Science.gov (United States)

Li, Jing; Chen, Xiangrong; Qi, Benkun; Luo, Jianquan; Zhang, Yuming; Su, Yi; Wan, Yinhua

2014-10-01

Production of acetone-butanol-ethanol (ABE) from cassava was investigated with a fermentation-pervaporation (PV) coupled process. ABE products were in situ removed from fermentation broth to alleviate the toxicity of solvent to the Clostridium acetobutylicum DP217. Compared to the batch fermentation without PV, glucose consumption rate and solvent productivity increased by 15% and 21%, respectively, in batch fermentation-PV coupled process, while in continuous fermentation-PV coupled process running for 304 h, the substrate consumption rate, solvent productivity and yield increased by 58%, 81% and 15%, reaching 2.02 g/Lh, 0.76 g/Lh and 0.38 g/g, respectively. Silicalite-1 filled polydimethylsiloxane (PDMS)/polyacrylonitrile (PAN) membrane modules ensured media recycle without significant fouling, steadily generating a highly concentrated ABE solution containing 201.8 g/L ABE with 122.4 g/L butanol. After phase separation, a final product containing 574.3g/L ABE with 501.1g/L butanol was obtained. Therefore, the fermentation-PV coupled process has the potential to decrease the cost in ABE production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Transition from reversible to irreversible magnetic exchange-spring processes in antiferromagnetically exchange-coupled hard/soft/hard trilayer structures

International Nuclear Information System (INIS)

Wang Xiguang; Guo Guanghua; Zhang Guangfu

2011-01-01

The demagnetization processes of antiferromagnetically exchange-coupled hard/soft/hard trilayer structures have been studied based on the discrete one-dimensional atomic chain model and the linear partial domain-wall model. It is found that, when the magnetic anisotropy of soft layer is taken into account, the changes of the soft layer thickness and the interfacial exchange coupling strength may lead a transition of demagnetization process in soft layer from the reversible to the irreversible magnetic exchange-spring process. For the trilayer structures with very thin soft layer, the demagnetization process exhibits typical reversible exchange-spring behavior. However, as the thickness of soft layer is increased, there is a crossover point t c , after which the process becomes irreversible. Similarly, there is also a critical interfacial exchange coupling constant A sh c , above which the exchange-spring process is reversible. When A sh sh c , the irreversible exchange-spring process is achieved. The phase diagram of reversible and irreversible exchange-spring processes is mapped in the plane of the interfacial exchange coupling A sh and soft layer thickness N s . - Research highlights: → A differing magnetic exchange-spring process is found in antiferromagnetically exchange-coupled hard/soft/hard trilayers if the magnetic anisotropy of the soft layers is taken into account. → The change of the soft layer thickness may lead to a transition of demagnetization process in soft layer from the reversible to the irreversible exchange-spring process. → The change of the soft-hard interfacial exchange coupling strength may lead a transition of demagnetization process in soft layer from the reversible to the irreversible exchange-spring process. → The phase diagram of reversible and irreversible exchange-spring processes is mapped in the plane of the interfacial exchange coupling and soft layer thickness.

Main outcomes from in situ thermo-hydro-mechanical experiments programme to demonstrate feasibility of radioactive high-level waste disposal in the Callovo-Oxfordian claystone

Directory of Open Access Journals (Sweden)

G. Armand

2017-06-01

Full Text Available In the context of radioactive waste disposal, an underground research laboratory (URL is a facility in which experiments are conducted to demonstrate the feasibility of constructing and operating a radioactive waste disposal facility within a geological formation. The Meuse/Haute-Marne URL is a site-specific facility planned to study the feasibility of a radioactive waste disposal in the Callovo-Oxfordian (COx claystone. The thermo-hydro-mechanical (THM behaviour of the host rock is significant for the design of the underground nuclear waste disposal facility and for its long-term safety. The French National Radioactive Waste Management Agency (Andra has begun a research programme aiming to demonstrate the relevancy of the French high-level waste (HLW concept. This paper presents the programme implemented from small-scale (small diameter boreholes to full-scale demonstration experiments to study the THM effects of the thermal transient on the COx claystone and the strategy implemented in this new programme to demonstrate and optimise current disposal facility components for HLW. It shows that the French high-level waste concept is feasible and working in the COx claystone. It also exhibits that, as for other plastic clay or claystone, heating-induced pore pressure increases and that the THM behaviour is anisotropic.

A cross-coupled-structure-based temperature sensor with reduced process variation sensitivity

Energy Technology Data Exchange (ETDEWEB)

Tie Meng; Cheng Xu, E-mail: tiemeng@mprc.pku.edu.c [Microprocessor Research and Development Center, Peking University, Beijing 100871 (China)

2009-04-15

An innovative, thermally-insensitive phenomenon of cascaded cross-coupled structures is found. And a novel CMOS temperature sensor based on a cross-coupled structure is proposed. This sensor consists of two different ring oscillators. The first ring oscillator generates pulses that have a period, changing linearly with temperature. Instead of using the system clock like in traditional sensors, the second oscillator utilizes a cascaded cross-coupled structure to generate temperature independent pulses to capture the result from the first oscillator. Due to the compensation between the two ring oscillators, errors caused by supply voltage variations and systematic process variations are reduced. The layout design of the sensor is based on the TSMC13G process standard cell library. Only three inverters are modified for proper channel width tuning without any other custom design. This allows for an easy integration of the sensor into cell-based chips. Post-layout simulations results show that an error lower than +-1.1 deg. C can be achieved in the full temperature range from -40 to 120 deg. C. As shown by SPICE simulations, the thermal insensitivity of the cross-coupled inverters can be realized for various TSMC technologies: 0.25 mum, 0.18 mum, 0.13 mum, and 65 nm.

Effect of process parameters on temperature distribution in twin-electrode TIG coupling arc

Science.gov (United States)

Zhang, Guangjun; Xiong, Jun; Gao, Hongming; Wu, Lin

2012-10-01

The twin-electrode TIG coupling arc is a new type of welding heat source, which is generated in a single welding torch that has two tungsten electrodes insulated from each other. This paper aims at determining the distribution of temperature for the coupling arc using the Fowler-Milne method under the assumption of local thermodynamic equilibrium. The influences of welding current, arc length, and distance between both electrode tips on temperature distribution of the coupling arc were analyzed. Based on the results, a better understanding of the twin-electrode TIG welding process was obtained.

Low Variance Couplings for Stochastic Models of Intracellular Processes with Time-Dependent Rate Functions.

Science.gov (United States)

Anderson, David F; Yuan, Chaojie

2018-04-18

A number of coupling strategies are presented for stochastically modeled biochemical processes with time-dependent parameters. In particular, the stacked coupling is introduced and is shown via a number of examples to provide an exceptionally low variance between the generated paths. This coupling will be useful in the numerical computation of parametric sensitivities and the fast estimation of expectations via multilevel Monte Carlo methods. We provide the requisite estimators in both cases.

Panel report on coupled thermo-mechanical-hydro-chemical processes associated with a nuclear waste repository

International Nuclear Information System (INIS)

Tsang, C.F.; Mangold, D.C.

1984-07-01

Four basic physical processes, thermal, hydrological, mechanical and chemical, are likely to occur in 11 different types of coupling during the service life of an underground nuclear waste repository. A great number of coupled processes with various degrees of importance for geological repositories were identified and arranged into these 11 types. A qualitative description of these processes and a tentative evaluation of their significance and the degree of uncertainty in prediction is given. Suggestions for methods of investigation generally include, besides theoretical work, laboratory and large scale field testing. Great efforts of a multidisciplinary nature are needed to elucidate details of several coupled processes under different temperature conditions in different geological formations. It was suggested that by limiting the maximum temperature to 100 0 C in the backfill and in the host rock during the whole service life of the repository the uncertainties in prediction of long-term repository behavior might be considerably reduced

Panel report on coupled thermo-mechanical-hydro-chemical processes associated with a nuclear waste repository

Energy Technology Data Exchange (ETDEWEB)

Tsang, C.F.; Mangold, D.C. (eds.)

1984-07-01

Four basic physical processes, thermal, hydrological, mechanical and chemical, are likely to occur in 11 different types of coupling during the service life of an underground nuclear waste repository. A great number of coupled processes with various degrees of importance for geological repositories were identified and arranged into these 11 types. A qualitative description of these processes and a tentative evaluation of their significance and the degree of uncertainty in prediction is given. Suggestions for methods of investigation generally include, besides theoretical work, laboratory and large scale field testing. Great efforts of a multidisciplinary nature are needed to elucidate details of several coupled processes under different temperature conditions in different geological formations. It was suggested that by limiting the maximum temperature to 100{sup 0}C in the backfill and in the host rock during the whole service life of the repository the uncertainties in prediction of long-term repository behavior might be considerably reduced.

Global land-atmosphere coupling associated with cold climate processes

Science.gov (United States)

Dutra, Emanuel

This dissertation constitutes an assessment of the role of cold processes, associated with snow cover, in controlling the land-atmosphere coupling. The work was based on model simulations, including offline simulations with the land surface model HTESSEL, and coupled atmosphere simulations with the EC-EARTH climate model. A revised snow scheme was developed and tested in HTESSEL and EC-EARTH. The snow scheme is currently operational at the European Centre for Medium-Range Weather Forecasts integrated forecast system, and in the default configuration of EC-EARTH. The improved representation of the snowpack dynamics in HTESSEL resulted in improvements in the near surface temperature simulations of EC-EARTH. The new snow scheme development was complemented with the option of multi-layer version that showed its potential in modeling thick snowpacks. A key process was the snow thermal insulation that led to significant improvements of the surface water and energy balance components. Similar findings were observed when coupling the snow scheme to lake ice, where lake ice duration was significantly improved. An assessment on the snow cover sensitivity to horizontal resolution, parameterizations and atmospheric forcing within HTESSEL highlighted the role of the atmospheric forcing accuracy and snowpack parameterizations in detriment of horizontal resolution over flat regions. A set of experiments with and without free snow evolution was carried out with EC-EARTH to assess the impact of the interannual variability of snow cover on near surface and soil temperatures. It was found that snow cover interannual variability explained up to 60% of the total interannual variability of near surface temperature over snow covered regions. Although these findings are model dependent, the results showed consistency with previously published work. Furthermore, the detailed validation of the snow dynamics simulations in HTESSEL and EC-EARTH guarantees consistency of the results.

Effect of process parameters on temperature distribution in twin-electrode TIG coupling arc

International Nuclear Information System (INIS)

Zhang, Guangjun; Xiong, Jun; Gao, Hongming; Wu, Lin

2012-01-01

The twin-electrode TIG coupling arc is a new type of welding heat source, which is generated in a single welding torch that has two tungsten electrodes insulated from each other. This paper aims at determining the distribution of temperature for the coupling arc using the Fowler–Milne method under the assumption of local thermodynamic equilibrium. The influences of welding current, arc length, and distance between both electrode tips on temperature distribution of the coupling arc were analyzed. Based on the results, a better understanding of the twin-electrode TIG welding process was obtained. -- Highlights: ► Increasing arc current will increase the coupling arc temperature. ► Arc length seldom affects the peak temperature of the coupling arc. ► Increasing arc length will increase the extension of temperature near the anode. ► Increasing distance will decrease temperatures in the central part of the arc.

Modeling Coupled THMC Processes and Brine Migration in Salt at High Temperatures

Energy Technology Data Exchange (ETDEWEB)

Rutqvist, Jonny; Blanco Martin, Laura; Mukhopadhyay, Sumit; Houseworth, Jim; Birkholzer, Jens

2014-08-14

In this report, we present FY2014 progress by Lawrence Berkeley National Laboratory (LBNL) related to modeling of coupled thermal-hydrological-mechanical-chemical (THMC) processes in salt and their effect on brine migration at high temperatures. LBNL’s work on the modeling of coupled THMC processes in salt was initiated in FY2012, focusing on exploring and demonstrating the capabilities of an existing LBNL modeling tool (TOUGH-FLAC) for simulating temperature-driven coupled flow and geomechanical processes in salt. This work includes development related to, and implementation of, essential capabilities, as well as testing the model against relevant information and published experimental data related to the fate and transport of water. we provide more details on the FY2014 work, first presenting updated tools and improvements made to the TOUGH-FLAC simulator, and the use of this updated tool in a new model simulation of long-term THM behavior within a generic repository in a salt formation. This is followed by the description of current benchmarking and validations efforts, including the TSDE experiment. We then present the current status in the development of constitutive relationships and the dual-continuum model for brine migration. We conclude with an outlook for FY2015, which will be much focused on model validation against field experiments and on the use of the model for the design studies related to a proposed heater experiment.

Exploring the Influence of Topography on Belowground C Processes Using a Coupled Hydrologic-Biogeochemical Model

Science.gov (United States)

Shi, Y.; Davis, K. J.; Eissenstat, D. M.; Kaye, J. P.; Duffy, C.; Yu, X.; He, Y.

2014-12-01

Belowground carbon processes are affected by soil moisture and soil temperature, but current biogeochemical models are 1-D and cannot resolve topographically driven hill-slope soil moisture patterns, and cannot simulate the nonlinear effects of soil moisture on carbon processes. Coupling spatially-distributed physically-based hydrologic models with biogeochemical models may yield significant improvements in the representation of topographic influence on belowground C processes. We will couple the Flux-PIHM model to the Biome-BGC (BBGC) model. Flux-PIHM is a coupled physically-based land surface hydrologic model, which incorporates a land-surface scheme into the Penn State Integrated Hydrologic Model (PIHM). The land surface scheme is adapted from the Noah land surface model. Because PIHM is capable of simulating lateral water flow and deep groundwater, Flux-PIHM is able to represent the link between groundwater and the surface energy balance, as well as the land surface heterogeneities caused by topography. The coupled Flux-PIHM-BBGC model will be tested at the Susquehanna/Shale Hills critical zone observatory (SSHCZO). The abundant observations, including eddy covariance fluxes, soil moisture, groundwater level, sap flux, stream discharge, litterfall, leaf area index, above ground carbon stock, and soil carbon efflux, make SSHCZO an ideal test bed for the coupled model. In the coupled model, each Flux-PIHM model grid will couple a BBGC cell. Flux-PIHM will provide BBGC with soil moisture and soil temperature information, while BBGC provides Flux-PIHM with leaf area index. Preliminary results show that when Biome- BGC is driven by PIHM simulated soil moisture pattern, the simulated soil carbon is clearly impacted by topography.

Report of the second meeting of the consultants on coupled processes associated with geological disposal of nuclear waste

International Nuclear Information System (INIS)

Tsang, Chin-Fu; Mangold, D.C.

1985-09-01

The second meeting of the Consultants on Coupled Processes Associated with Geological Disposal of Nuclear Waste occurred on January 15-16, 1985 at Lawrence Berkeley Laboratory (LBL). All the consultants were present except Dr. K. Kovari, who presented comments in writing afterward. This report contains a brief summary of the presentations and discussions from the meeting. The main points of the speakers' topics are briefly summarized in the report. Some points that emerged during the discussions of the presentations are included in the text related to the respective talks. These comments are grouped under the headings: Comments on Coupled Processes in Unsaturated Fractured Porous Media, Comments on Overview of Coupled Processes, Presentations by Consultants on Selected Topics of Current Interest in Coupled Processes, and Recommendations for Underground Field Tests with Applications to Three Geologic Environments

Coupling of Processes and Data in PennState Integrated Hydrologic Modeling (PIHM) System

Science.gov (United States)

Kumar, M.; Duffy, C.

2007-12-01

Full physical coupling, "natural" numerical coupling and parsimonious but accurate data coupling is needed to comprehensively and accurately capture the interaction between different components of a hydrologic continuum. Here we present a physically based, spatially distributed hydrologic model that incorporates all the three coupling strategies. Physical coupling of interception, snow melt, transpiration, overland flow, subsurface flow, river flow, macropore based infiltration and stormflow, flow through and over hydraulic structures likes weirs and dams, and evaporation from interception, ground and overland flow is performed. All the physically coupled components are numerically coupled through semi-discrete form of ordinary differential equations, that define each hydrologic process, using Finite-Volume based approach. The fully implicit solution methodology using CVODE solver solves for all the state variables simultaneously at each adaptive time steps thus providing robustness, stability and accuracy. The accurate data coupling is aided by use of constrained unstructured meshes, flexible data model and use of PIHMgis. The spatial adaptivity of decomposed domain and temporal adaptivity of the numerical solver facilitates capture of varied spatio-temporal scales that are inherent in hydrologic process interactions. The implementation of the model has been performed on a meso-scale Little-Juniata Watershed. Model results are validated by comparison of streamflow at multiple locations. We discuss some of the interesting hydrologic interactions between surface, subsurface and atmosphere witnessed during the year long simulation such as a) inverse relationship between evaporation from interception storage and transpiration b) relative influence of forcing (precipitation, temperature and radiation) and source (soil moisture and overland flow) on evaporation c) influence of local topography on gaining, loosing or "flow-through" behavior of river-aquifer interactions

Contribution to the optimization of the coupling of nuclear reactors to desalination processes

International Nuclear Information System (INIS)

Dardour, S.

2007-04-01

This work deals with modelling, simulation and optimization of the coupling between nuclear reactors (PWR, modular high temperature reactors) and desalination processes (multiple effect distillation, reverse osmosis). The reactors considered in this study are PWR (Pressurized Water Reactor) and GTMHR (Gas Turbine Modular Helium Reactor). The desalination processes retained are MED (Multi Effect Distillation) and SWRO (Sea Water Reverse Osmosis). A software tool: EXCELEES of thermodynamic modelling of coupled systems, based on the Engineering Algebraic Equation Solver has been developed. Models of energy conversion systems and of membrane desalination processes and distillation have been developed. Based on the first and second principles of thermodynamics, these models have allowed to determine the optimal running point of the coupled systems. The thermodynamic analysis has been completed by a first economic evaluation. Based on the use of the DEEP software of the IAEA, this evaluation has confirmed the interest to use these types of reactors for desalination. A modelling tool of thermal processes of desalination in dynamic condition has been developed too. This tool has been applied to the study of the dynamics of an existing plant and has given satisfying results. A first safety checking has been at last carried out. The transients able to jeopardize the integrated system have been identified. Several measures aiming at consolidate the safety have been proposed. (O.M.)

On the Coupling Time of the Heat-Bath Process for the Fortuin-Kasteleyn Random-Cluster Model

Science.gov (United States)

Collevecchio, Andrea; Elçi, Eren Metin; Garoni, Timothy M.; Weigel, Martin

2018-01-01

We consider the coupling from the past implementation of the random-cluster heat-bath process, and study its random running time, or coupling time. We focus on hypercubic lattices embedded on tori, in dimensions one to three, with cluster fugacity at least one. We make a number of conjectures regarding the asymptotic behaviour of the coupling time, motivated by rigorous results in one dimension and Monte Carlo simulations in dimensions two and three. Amongst our findings, we observe that, for generic parameter values, the distribution of the appropriately standardized coupling time converges to a Gumbel distribution, and that the standard deviation of the coupling time is asymptotic to an explicit universal constant multiple of the relaxation time. Perhaps surprisingly, we observe these results to hold both off criticality, where the coupling time closely mimics the coupon collector's problem, and also at the critical point, provided the cluster fugacity is below the value at which the transition becomes discontinuous. Finally, we consider analogous questions for the single-spin Ising heat-bath process.

Integrated Modeling and Experiments to Characterize Coupled Thermo-hydro-geomechanical-chemical processes in Hydraulic Fracturing

Science.gov (United States)

Viswanathan, H. S.; Carey, J. W.; Karra, S.; Porter, M. L.; Rougier, E.; Kang, Q.; Makedonska, N.; Hyman, J.; Jimenez Martinez, J.; Frash, L.; Chen, L.

2015-12-01

Hydraulic fracturing phenomena involve fluid-solid interactions embedded within coupled thermo-hydro-mechanical-chemical (THMC) processes over scales from microns to tens of meters. Feedbacks between processes result in complex dynamics that must be unraveled if one is to predict and, in the case of unconventional resources, facilitate fracture propagation, fluid flow, and interfacial transport processes. The proposed work is part of a broader class of complex systems involving coupled fluid flow and fractures that are critical to subsurface energy issues, such as shale oil, geothermal, carbon sequestration, and nuclear waste disposal. We use unique LANL microfluidic and triaxial core flood experiments integrated with state-of-the-art numerical simulation to reveal the fundamental dynamics of fracture-fluid interactions to characterize the key coupled processes that impact hydrocarbon production. We are also comparing CO2-based fracturing and aqueous fluids to enhance production, greatly reduce waste water, while simultaneously sequestering CO2. We will show pore, core and reservoir scale simulations/experiments that investigate the contolling mechanisms that control hydrocarbon production.

Cross-frequency coupling in deep brain structures upon processing the painful sensory inputs.

Science.gov (United States)

Liu, C C; Chien, J H; Kim, J H; Chuang, Y F; Cheng, D T; Anderson, W S; Lenz, F A

2015-09-10

Cross-frequency coupling has been shown to be functionally significant in cortical information processing, potentially serving as a mechanism for integrating functionally relevant regions in the brain. In this study, we evaluate the hypothesis that pain-related gamma oscillatory responses are coupled with low-frequency oscillations in the frontal lobe, amygdala and hippocampus, areas known to have roles in pain processing. We delivered painful laser pulses to random locations on the dorsal hand of five patients with uncontrolled epilepsy requiring depth electrode implantation for seizure monitoring. Two blocks of 40 laser stimulations were delivered to each subject and the pain-intensity was controlled at five in a 0-10 scale by adjusting the energy level of the laser pulses. Local-field-potentials (LFPs) were recorded through bilaterally implanted depth electrode contacts to study the oscillatory responses upon processing the painful laser stimulations. Our results show that painful laser stimulations enhanced low-gamma (LH, 40-70 Hz) and high-gamma (HG, 70-110 Hz) oscillatory responses in the amygdala and hippocampal regions on the right hemisphere and these gamma responses were significantly coupled with the phases of theta (4-7 Hz) and alpha (8-1 2 Hz) rhythms during pain processing. Given the roles of these deep brain structures in emotion, these findings suggest that the oscillatory responses in these regions may play a role in integrating the affective component of pain, which may contribute to our understanding of the mechanisms underlying the affective information processing in humans. Copyright © 2015 IBRO. Published by Elsevier Ltd. All rights reserved.

Thermo-Hydro Mechanical Characteristics and Processes in the Clay Barrier of a High Level Radioactive Waste Repository. State of the Art Report

International Nuclear Information System (INIS)

Villar, M. V.

2004-01-01

This document is a summary of the available information on the thermo-hydro-mechanical properties of the bentonite barrier of a high-level radioactive waste repository and of the processes taking place in it during the successive repository operation phases. Mainly the thermal properties, the volume change processes (swelling and consolidation), the permeability and the water retention capacity are analysed. A review is made of the existing experimental knowledge on the modification of the these properties by the effect of temperature, water salinity, humidity and density of the bentonite, and their foreseen evolution as a consequence of the processes expected in the repository. The compiled evolution refers mostly to the FEBEX (Spain), the MX-80 (USA) and the FoCa (France) bentonite, considered as reference barrier materials in several European disposal concepts. (Author) 102 refs

Thermo-Hydro Mechanical Characteristics and Processes in the Clay Barrier of a High Level Radioactive Waste Repository. State of the Art Report

Energy Technology Data Exchange (ETDEWEB)

Villar, M. V.

2004-07-01

This document is a summary of the available information on the thermo-hydro-mechanical properties of the bentonite barrier of a high-level radioactive waste repository and of the processes taking place in it during the successive repository operation phases. Mainly the thermal properties, the volume change processes (swelling and consolidation), the permeability and the water retention capacity are analysed. A review is made of the existing experimental knowledge on the modification of the these properties by the effect of temperature, water salinity, humidity and density of the bentonite, and their foreseen evolution as a consequence of the processes expected in the repository. The compiled evolution refers mostly to the FEBEX (Spain), the MX-80 (US) and the FoCa (France) bentonite, considered as reference barrier materials in several European disposal concepts. (Author) 102 refs.

The Experience of Chinese Couples Undergoing In Vitro Fertilization Treatment: Perception of the Treatment Process and Partner Support.

Science.gov (United States)

Ying, Li-Ying; Wu, Lai Har; Loke, Alice Yuen

2015-01-01

Couples undergoing In Vitro Fertilization (IVF) Treatment suffer as dyads from the stressful experience of the painful treatment and the fear that the IVF cycle will fail. They are likely to report that their marital relationship has become unstable due to the prolonged period of treatment. This is a qualitative study that was conducted to explore the experiences that Chinese couples have had with IVF treatment, especially their perceptions of the process and the support between couples. The interviews revealed that couples suffered from the process, experiencing physical and emotional pain, struggling with the urgency and inflexibility of bearing a child, and experiencing disturbances in their daily routines and work. The participants described how they endured the hardships as a couple and how it affected their relationship. The couples felt that sharing feelings and supporting each other contribute to psychological well-being and improves the marital relationship. They also identified some unfavorable aspects in their partner relationship. They were ambivalent about receiving social support from friends and family members. With the couples indicating that the support that they received from each other affected their experience during the treatment process, it is suggested that a supportive intervention that focuses on enhancing the partnership of the couples and dealing with their inflexibility on the issue of bearing a child might result in improvements in the psychological status and marital relationship of infertile couples undergoing IVF treatment.

The Experience of Chinese Couples Undergoing In Vitro Fertilization Treatment: Perception of the Treatment Process and Partner Support.

Directory of Open Access Journals (Sweden)

Li-Ying Ying

Full Text Available Couples undergoing In Vitro Fertilization (IVF Treatment suffer as dyads from the stressful experience of the painful treatment and the fear that the IVF cycle will fail. They are likely to report that their marital relationship has become unstable due to the prolonged period of treatment.This is a qualitative study that was conducted to explore the experiences that Chinese couples have had with IVF treatment, especially their perceptions of the process and the support between couples.The interviews revealed that couples suffered from the process, experiencing physical and emotional pain, struggling with the urgency and inflexibility of bearing a child, and experiencing disturbances in their daily routines and work. The participants described how they endured the hardships as a couple and how it affected their relationship. The couples felt that sharing feelings and supporting each other contribute to psychological well-being and improves the marital relationship. They also identified some unfavorable aspects in their partner relationship. They were ambivalent about receiving social support from friends and family members.With the couples indicating that the support that they received from each other affected their experience during the treatment process, it is suggested that a supportive intervention that focuses on enhancing the partnership of the couples and dealing with their inflexibility on the issue of bearing a child might result in improvements in the psychological status and marital relationship of infertile couples undergoing IVF treatment.

Health, trust, or "just understood": explicit and implicit condom decision-making processes among black, white, and interracial same-sex male couples.

Science.gov (United States)

Campbell, Chadwick K; Gómez, Anu Manchikanti; Dworkin, Shari; Wilson, Patrick A; Grisham, Kirk K; McReynolds, Jaih; Vielehr, Peter; Hoff, Colleen

2014-05-01

Among gay and bisexual men, primary partners are a leading source of HIV infection. Trust, intimacy, and advancements in HIV treatment may impact same-sex male (SSM) couples' decisions to engage in unprotected anal intercourse (UAI). This qualitative study explored how Black, White and interracial couples discussed, and made decisions regarding condoms. Qualitative interviews were conducted with 48 SSM couples in the New York and San Francisco metropolitan areas. Stratified purposive sampling was used to include Black (n = 16), White (n = 17), and interracial (Black-White) (n = 15) couples. Twenty-six couples were concordant HIV-negative and 22 were HIV-discordant. Interviews were recorded, transcribed, coded, and analyzed using a grounded theory approach. Some couples described explicit processes, which involved active discussion, while others described implicit processes, where condom-use decisions occurred without any explicit discussion. These processes also differed by race and HIV status. Black couples tended to report condom-use as "just understood." White, HIV-discordant couples decided not to use condoms, with some identifying the HIV-positive partner's suppressed viral load and high CD4 count as deciding factors. After an unplanned episode of UAI, White, HIV-negative couples tended to discontinue condom use while Black HIV-negative couples decided to revert to using condoms. HIV prevention efforts focused on same-sex, male couples must consider the explicit/implicit nature of condom decision-making processes. Understanding differences in these processes and considering relationship dynamics, across race and HIV status, can promote the development of innovative couple-level, HIV prevention interventions.

Modelling Coupled Processes in the Evolution of Repository Engineered Barrier Systems using QPAC-EBS

Energy Technology Data Exchange (ETDEWEB)

Maul, Philip; Benbow, Steven; Bond, Alex; Robinson, Peter (Quintessa Limited, Henley-on-Thames (United Kingdom))

2010-08-15

A satisfactory understanding of the evolution of repository engineered barrier systems (EBS) is an essential part of the safety case for the repository. This involves consideration of coupled Thermal (T), Hydro (H), Mechanical (M) and Chemical (C) processes. Quintessa's general-purpose modelling code QPAC is capable of representing strongly coupled non-linear processes and has been used in a wide range of applications. This code is the basis for software used by Quintessa in studies of the evolution of the EBS in a deep repository for spent nuclear fuel undertaken for SKI and then SSM since 2007. The collection of software components employed has been referred to collectively as QPAC-EBS, consisting of the core QPAC code together with relevant modules for T, H, M and C processes. QPAC-EBS employs a fundamentally different approach from dedicated codes that model such processes (although few codes can represent each type of process), enabling the specification of new processes and the associated governing equations in code input. Studies undertaken to date have demonstrated that QPAC-EBS can be used effectively to investigate both the early evolution of the EBS and important scenarios for the later evolution of the system when buffer erosion and canister corrosion may occur. A key issue for modelling EBS evolution is the satisfactory modelling of the behaviour of the bentonite buffer. Bentonite is a difficult material to model, partly because of the complex coupled mechanical, hydro and chemical processes involved in swelling during resaturation. Models employed to date have generally taken an empirical approach, but a new model developed during the EU THERESA project could be further developed to provide a better representation of these processes. QPAC-EBS could play an important role in supporting SSM.s review of the forthcoming SR-Site assessment by SKB if used by Quintessa in independent supporting calculations. To date radionuclide transport calculations

Overview of coupled processes with emphasis in geochemistry

International Nuclear Information System (INIS)

Langmuir, D.

1987-01-01

Many coupled and uncoupled geochemical processes that can control the mobility of radionuclides from a breached repository are not adequately understood. Mobilization of radionuclides and related substances in ground water may occur by dissolution, desorption, or colloidal deflocculation. Transport may be carried out by advection, diffusion, membrane transport, or polymer-colloidal movement. Deposition may occur by precipitation or coprecipitation, adsorption, filtration, and flocculation and settling of colloids. Most of these processes cannot be rigorously understood without adequate thermodynamic and kinetic data bases. Empirically derived thermodynamic and kinetic data for radionuclides and related substances are largely lacking above 25 degrees C and 1 bar pressure, although in some cases sufficiently accurate estimates of such data are now possible. Computer programs that can evaluate the status of reactions in water-rock systems as well as predict such reactions are available. This paper discusses how such programs and data bases are essential to define ground water conditions prior to repository siting and to predict repository performance after emplacement of waste

Powder processing and spheroidizing with thermal inductively coupled plasma

International Nuclear Information System (INIS)

Nutsch, G.; Linke, P.; Zakharian, S.; Dzur, B.; Weiss, K.-H.

2001-01-01

Processing of advanced powder materials for the spraying industry is one of the most promising applications of the thermal RF inductively coupled plasma. By selecting the feedstock carefully and adjusting the RF plasma parameters, unique materials with high quality can be achieved. Powders injected in the hot plasma core emerge with modified shapes, morphology, crystal structure and chemical composition. Ceramic oxide powders such as Al 2 O 3 , ZrO 2 , SiO 2 are spheroidized with a high spheroidization rate. By using the RF induction plasma spheroidizing process tungsten melt carbide powders are obtained with a high spheroidization rate at high feeding rates by densification of agglomerated powders consisting of di-tungsten carbide and monocarbide with a definite composition. This kind of ball-like powders is particularly suited for wear resistant applications. (author)

Contagion processes on the static and activity-driven coupling networks

Science.gov (United States)

Lei, Yanjun; Jiang, Xin; Guo, Quantong; Ma, Yifang; Li, Meng; Zheng, Zhiming

2016-03-01

The evolution of network structure and the spreading of epidemic are common coexistent dynamical processes. In most cases, network structure is treated as either static or time-varying, supposing the whole network is observed in the same time window. In this paper, we consider the epidemics spreading on a network which has both static and time-varying structures. Meanwhile, the time-varying part and the epidemic spreading are supposed to be of the same time scale. We introduce a static and activity-driven coupling (SADC) network model to characterize the coupling between the static ("strong") structure and the dynamic ("weak") structure. Epidemic thresholds of the SIS and SIR models are studied using the SADC model both analytically and numerically under various coupling strategies, where the strong structure is of homogeneous or heterogeneous degree distribution. Theoretical thresholds obtained from the SADC model can both recover and generalize the classical results in static and time-varying networks. It is demonstrated that a weak structure might make the epidemic threshold low in homogeneous networks but high in heterogeneous cases. Furthermore, we show that the weak structure has a substantive effect on the outbreak of the epidemics. This result might be useful in designing some efficient control strategies for epidemics spreading in networks.

Coupled Modeling of Rhizosphere and Reactive Transport Processes

Science.gov (United States)

Roque-Malo, S.; Kumar, P.

2017-12-01

The rhizosphere, as a bio-diverse plant root-soil interface, hosts many hydrologic and biochemical processes, including nutrient cycling, hydraulic redistribution, and soil carbon dynamics among others. The biogeochemical function of root networks, including the facilitation of nutrient cycling through absorption and rhizodeposition, interaction with micro-organisms and fungi, contribution to biomass, etc., plays an important role in myriad Critical Zone processes. Despite this knowledge, the role of the rhizosphere on watershed-scale ecohydrologic functions in the Critical Zone has not been fully characterized, and specifically, the extensive capabilities of reactive transport models (RTMs) have not been applied to these hydrobiogeochemical dynamics. This study uniquely links rhizospheric processes with reactive transport modeling to couple soil biogeochemistry, biological processes, hydrologic flow, hydraulic redistribution, and vegetation dynamics. Key factors in the novel modeling approach are: (i) bi-directional effects of root-soil interaction, such as simultaneous root exudation and nutrient absorption; (ii) multi-state biomass fractions in soil (i.e. living, dormant, and dead biological and root materials); (iii) expression of three-dimensional fluxes to represent both vertical and lateral interconnected flows and processes; and (iv) the potential to include the influence of non-stationary external forcing and climatic factors. We anticipate that the resulting model will demonstrate the extensive effects of plant root dynamics on ecohydrologic functions at the watershed scale and will ultimately contribute to a better characterization of efflux from both agricultural and natural systems.

Treatment of oilfield produced water by anaerobic process coupled with micro-electrolysis.

Science.gov (United States)

Li, Gang; Guo, Shuhai; Li, Fengmei

2010-01-01

Treatment of oilfield produced water was investigated using an anaerobic process coupled with micro-electrolysis (ME), focusing on changes in chemical oxygen demand (COD) and biodegradability. Results showed that COD exhibited an abnormal change in the single anaerobic system in which it increased within the first 168 hr, but then decreased to 222 mg/L after 360 hr. The biological oxygen demand (five-day) (BODs)/COD ratio of the water increased from 0.05 to 0.15. Hydrocarbons in the wastewater, such as pectin, degraded to small molecules during the hydrolytic acidification process. Comparatively, the effect of ME was also investigated. The COD underwent a slight decrease and the BOD5/COD ratio of the water improved from 0.05 to 0.17 after ME. Removal of COD was 38.3% under the idealized ME conditions (pH 6.0), using iron and active carbon (80 and 40 g/L, respectively). Coupling the anaerobic process with ME accelerated the COD removal ratio (average removal was 53.3%). Gas chromatography/mass spectrometry was used to analyze organic species conversion. This integrated system appeared to be a useful option for the treatment of water produced in oilfields.

Signatures of Förster and Dexter transfer processes in coupled nanostructures for linear and two-dimensional coherent optical spectroscopy

Science.gov (United States)

Specht, Judith F.; Richter, Marten

2015-03-01

In this manuscript, we study the impact of the two Coulomb induced resonance energy transfer processes, Förster and Dexter coupling, on the spectral signatures obtained by double quantum coherence spectroscopy. We show that the specific coupling characteristics allow us to identify the underlying excitation transfer mechanism by means of specific signatures in coherent spectroscopy. Therefore, we control the microscopic calculated coupling strength of spin preserving and spin flipping Förster transfer processes by varying the mutual orientation of the two quantum emitters. The calculated spectra reveal the optical selection rules altered by Förster and Dexter coupling between two semiconductor quantum dots. We show that Dexter coupling between bright and dark two-exciton states occurs.

COUPLED ATOMIZATION AND SPRAY MODELLING IN THE SPRAY FORMING PROCESS USING OPENFOAM

DEFF Research Database (Denmark)

Gjesing, Rasmus; Hattel, Jesper Henri; Fritsching, Udo

2009-01-01

The paper presents a numerical model capable of simulating the atomization, break-up and in-flight spray phenomena in the spray forming process. The model is developed and implemented in the freeware code openFOAM. The focus is on studying the coupling effect of the melt break-up phenomena...

Sensitivity Studies of Advanced Reactors Coupled to High Temperature Electrolysis (HTE) Hydrogen Production Processes

International Nuclear Information System (INIS)

Edwin A. Harvego; Michael G. McKellar; James E. O'Brien; J. Stephen Herring

2007-01-01

High Temperature Electrolysis (HTE), when coupled to an advanced nuclear reactor capable of operating at reactor outlet temperatures of 800 C to 950 C, has the potential to efficiently produce the large quantities of hydrogen needed to meet future energy and transportation needs. To evaluate the potential benefits of nuclear-driven hydrogen production, the UniSim process analysis software was used to evaluate different reactor concepts coupled to a reference HTE process design concept. The reference HTE concept included an Intermediate Heat Exchanger and intermediate helium loop to separate the reactor primary system from the HTE process loops and additional heat exchangers to transfer reactor heat from the intermediate loop to the HTE process loops. The two process loops consisted of the water/steam loop feeding the cathode side of a HTE electrolysis stack, and the steam or air sweep loop used to remove oxygen from the anode side. The UniSim model of the process loops included pumps to circulate the working fluids and heat exchangers to recover heat from the oxygen and hydrogen product streams to improve the overall hydrogen production efficiencies. The reference HTE process loop model was coupled to separate UniSim models developed for three different advanced reactor concepts (a high-temperature helium cooled reactor concept and two different supercritical CO2 reactor concepts). Sensitivity studies were then performed to evaluate the affect of reactor outlet temperature on the power cycle efficiency and overall hydrogen production efficiency for each of the reactor power cycles. The results of these sensitivity studies showed that overall power cycle and hydrogen production efficiencies increased with reactor outlet temperature, but the power cycle producing the highest efficiencies varied depending on the temperature range considered

The influence of nonbilinear system-bath coupling on quantum-mechanical activated rate processes

International Nuclear Information System (INIS)

Navrotskaya, Irina; Geva, Eitan

2006-01-01

The dependence of quantum-mechanical activated rate processes on the system-bath coupling strength was investigated in the case of a double-well nonbilinearly coupled to a harmonic bath, where the system-bath coupling is linear in the bath coordinates and nonlinear in the reaction coordinate. Such nonbilinear coupling is known to give rise to a classical friction kernel which is explicitly dependent on the reaction coordinate. We show that it can also lead to quantum-mechanical barrier-crossing rates, whose dependence on the system-bath coupling strength is qualitatively different from that observed in the quantum-mechanical bilinear case and classical nonbilinear case. More specifically, it is shown that the quantum-mechanical barrier-crossing rate may monotonically increase as a function of the system-bath coupling strength, in cases where the classical barrier-crossing rate goes through a turnover, and that the rate of quantum-mechanical barrier-crossing can be lower than that of classical barrier-crossing. We show that those purely quantum-mechanical effects are of a thermodynamical, rather than dynamical, nature, and that they originate from the difference in friction between the barrier top and the reactant and product wells. Our conclusions are supported by results obtained via the CMD method, which were also found to be in very good agreement with numerically exact calculations based on the QUAPI method

The Decision-Making Process of Genetically At-Risk Couples Considering Preimplantation Genetic Diagnosis: Initial Findings from a Grounded Theory Study

Science.gov (United States)

Hershberger, Patricia E.; Gallo, Agatha M.; Kavanaugh, Karen; Olshansky, Ellen; Schwartz, Alan; Tur-Kaspa, Ilan

2012-01-01

Exponential growth in genomics has led to public and private initiatives worldwide that have dramatically increased the number of procreative couples who are aware of their ability to transmit genetic disorders to their future children. Understanding how couples process the meaning of being genetically at risk for their procreative life lags far behind the advances in genomic and reproductive sciences. Moreover, society, policy makers, and clinicians are not aware of the experiences and nuances involved when modern couples are faced with using Preimplantation Genetic Diagnosis (PGD). The purpose of this study was to discover the decision-making process of genetically at-risk couples as they decide whether to use PGD to prevent the transmission of known single-gene or sex-linked genetic disorders to their children. A qualitative, grounded theory design guided the study in which 22 couples (44 individual partners) from the USA, who were actively considering PGD, participated. Couples were recruited from June 2009 to May 2010 from the Internet and from a large PGD center and a patient newsletter. In-depth semi-structured interviews were completed with each individual partner within the couple dyad, separate from their respective partner. We discovered that couples move through four phases (Identify, Contemplate, Resolve, Engage) of a complex, dynamic, and iterative decision-making process where multiple, sequential decisions are made. In the Identify phase, couples acknowledge the meaning of their at-risk status. Parenthood and reproductive options are explored in the Contemplate phase, where 41% of couples remained for up to 36 months before moving into the Resolve phase. In Resolve, one of three decisions about PGD use is reached, including: Accepting, Declining, or Oscillating. Actualizing decisions occur in the Engage phase. Awareness of the decision-making process among genetically at-risk couples provides foundational work for understanding critical processes

THM modelling of buffer, backfill and other system components. Critical processes and scenarios

International Nuclear Information System (INIS)

Aakesson, Mattias; Kristensson, Ola; Boergesson, Lennart; Dueck, Ann; Hernelind, Jan

2010-03-01

A number of critical thermo-hydro-mechanical processes and scenarios for the buffer, tunnel backfill and other filling components in the repository have been identified. These processes and scenarios representing different aspects of the repository evolution have been pinpointed and modelled. In total, 22 cases have been modelled. Most cases have been analysed with finite element (FE) calculations, using primarily the two codes Abaqus and Code B right. For some cases analytical methods have been used either to supplement the FE calculations or due to that the scenario has a character that makes it unsuitable or very difficult to use the FE method. Material models and element models and choice of parameters as well as presumptions have been stated for all modelling cases. In addition, the results have been analysed and conclusions drawn for each case. The uncertainties have also been analysed. Besides the information given for all cases studied, the codes and material models have been described in a separate so called data report

THM modelling of buffer, backfill and other system components. Critical processes and scenarios

Energy Technology Data Exchange (ETDEWEB)

Aakesson, Mattias; Kristensson, Ola; Boergesson, Lennart; Dueck, Ann (Clay Technology AB, Lund (Sweden)); Hernelind, Jan (5T-Engineering AB, Vaesteraas (Sweden))

2010-03-15

A number of critical thermo-hydro-mechanical processes and scenarios for the buffer, tunnel backfill and other filling components in the repository have been identified. These processes and scenarios representing different aspects of the repository evolution have been pinpointed and modelled. In total, 22 cases have been modelled. Most cases have been analysed with finite element (FE) calculations, using primarily the two codes Abaqus and Code-Bright. For some cases analytical methods have been used either to supplement the FE calculations or due to that the scenario has a character that makes it unsuitable or very difficult to use the FE method. Material models and element models and choice of parameters as well as presumptions have been stated for all modelling cases. In addition, the results have been analysed and conclusions drawn for each case. The uncertainties have also been analysed. Besides the information given for all cases studied, the codes and material models have been described in a separate so called data report

Dynamical processes and epidemic threshold on nonlinear coupled multiplex networks

Science.gov (United States)

Gao, Chao; Tang, Shaoting; Li, Weihua; Yang, Yaqian; Zheng, Zhiming

2018-04-01

Recently, the interplay between epidemic spreading and awareness diffusion has aroused the interest of many researchers, who have studied models mainly based on linear coupling relations between information and epidemic layers. However, in real-world networks the relation between two layers may be closely correlated with the property of individual nodes and exhibits nonlinear dynamical features. Here we propose a nonlinear coupled information-epidemic model (I-E model) and present a comprehensive analysis in a more generalized scenario where the upload rate differs from node to node, deletion rate varies between susceptible and infected states, and infection rate changes between unaware and aware states. In particular, we develop a theoretical framework of the intra- and inter-layer dynamical processes with a microscopic Markov chain approach (MMCA), and derive an analytic epidemic threshold. Our results suggest that the change of upload and deletion rate has little effect on the diffusion dynamics in the epidemic layer.

Coupled numerical approach combining finite volume and lattice Boltzmann methods for multi-scale multi-physicochemical processes

Energy Technology Data Exchange (ETDEWEB)

Chen, Li; He, Ya-Ling [Key Laboratory of Thermo-Fluid Science and Engineering of MOE, School of Energy and Power Engineering, Xi' an Jiaotong University, Xi' an, Shaanxi 710049 (China); Kang, Qinjun [Computational Earth Science Group (EES-16), Los Alamos National Laboratory, Los Alamos, NM (United States); Tao, Wen-Quan, E-mail: wqtao@mail.xjtu.edu.cn [Key Laboratory of Thermo-Fluid Science and Engineering of MOE, School of Energy and Power Engineering, Xi' an Jiaotong University, Xi' an, Shaanxi 710049 (China)

2013-12-15

A coupled (hybrid) simulation strategy spatially combining the finite volume method (FVM) and the lattice Boltzmann method (LBM), called CFVLBM, is developed to simulate coupled multi-scale multi-physicochemical processes. In the CFVLBM, computational domain of multi-scale problems is divided into two sub-domains, i.e., an open, free fluid region and a region filled with porous materials. The FVM and LBM are used for these two regions, respectively, with information exchanged at the interface between the two sub-domains. A general reconstruction operator (RO) is proposed to derive the distribution functions in the LBM from the corresponding macro scalar, the governing equation of which obeys the convection–diffusion equation. The CFVLBM and the RO are validated in several typical physicochemical problems and then are applied to simulate complex multi-scale coupled fluid flow, heat transfer, mass transport, and chemical reaction in a wall-coated micro reactor. The maximum ratio of the grid size between the FVM and LBM regions is explored and discussed. -- Highlights: •A coupled simulation strategy for simulating multi-scale phenomena is developed. •Finite volume method and lattice Boltzmann method are coupled. •A reconstruction operator is derived to transfer information at the sub-domains interface. •Coupled multi-scale multiple physicochemical processes in micro reactor are simulated. •Techniques to save computational resources and improve the efficiency are discussed.

Two-dimensional spectroscopy: An approach to distinguish Förster and Dexter transfer processes in coupled nanostructures

Science.gov (United States)

Specht, Judith F.; Knorr, Andreas; Richter, Marten

2015-04-01

The linear and two-dimensional coherent optical spectra of Coulomb-coupled quantum emitters are discussed with respect to the underlying coupling processes. We present a theoretical analysis of the two different resonance energy transfer mechanisms between coupled nanostructures: Förster and Dexter interaction. Our investigation shows that the features visible in optical spectra of coupled quantum dots can be traced back to the nature of the underlying coupling mechanism (Förster or Dexter). Therefore, we discuss how the excitation transfer pathways can be controlled by choosing particular laser polarizations and mutual orientations of the quantum emitters in coherent two-dimensional spectroscopy. In this context, we analyze to what extent the delocalized double-excitonic states are bound to the optical selection rules of the uncoupled system.

Health, Trust, or “Just Understood”: Explicit and Implicit Condom Decision-Making Processes Among Black, White, and Interracial Same-Sex Male Couples

Science.gov (United States)

Campbell, Chadwick K.; Gómez, Anu Manchikanti; Dworkin, Shari; Wilson, Patrick A.; Grisham, Kirk; McReynolds, Jaih; Vielehr, Peter; Hoff, Colleen

2013-01-01

Among gay and bisexual men, primary partners are a leading source of HIV infection. Trust, intimacy, and advancements in HIV treatment may impact same-sex male couples’ decisions to engage in unprotected anal intercourse (UAI). This qualitative study explored how Black, White and interracial couples discussed, and made decisions regarding condoms. Qualitative interviews were conducted with 48 same-sex male couples in the New York and San Francisco metropolitan areas. Stratified purposive sampling was used to include Black (n = 16), White (n = 17), and interracial (Black-White) (n = 15) couples. Twenty-six couples were concordant HIV-negative and 22 were HIV-discordant. Interviews were recorded, transcribed, coded, and analyzed using a grounded theory approach. Some couples described explicit processes, which involved active discussion, while others described implicit processes, where condom-use decisions occurred without any explicit discussion. These processes also differed by race and HIV status. Black couples tended to report condom-use as “just understood.” White, HIV-discordant couples decided not to use condoms, with some identifying the HIV-positive partner’s suppressed viral load and high CD4 count as deciding factors. After an unplanned episode of UAI, White, HIV-negative couples tended to discontinue condom use while Black HIV-negative couples decided to revert to using condoms. HIV prevention efforts focused on same-sex, male couples must consider the explicit/implicit nature of condom decision-making processes. Understanding differences in these processes and considering relationship dynamics, across race and HIV status, can promote the development of innovative couple–level, HIV prevention interventions. PMID:23912774

Coupling the modular helium reactor to hydrogen production processes

International Nuclear Information System (INIS)

Richards, M.B.; Shenoy, A.S.; Schultz, K.R.

2004-01-01

Steam reforming of natural gas (methane) currently produces the bulk of hydrogen gas used in the world today. Because this process depletes natural gas resources and generates the greenhouse gas carbon dioxide as a by-product, there is a growing interest in using process heat and/or electricity generated by nuclear reactors to generate hydrogen by splitting water. Process heat from a high temperature nuclear reactor can be used directly to drive a set of chemical reactions, with the net result of splitting water into hydrogen and oxygen. For example, process heat at temperatures in the range 850 deg C to 950 deg C can drive the sulphur-iodine (S-I) thermochemical process to produce hydrogen with high efficiency. The S-I process produces highly pure hydrogen and oxygen, with formation, decomposition, regeneration, and recycle of the intermediate chemical reagents. Electricity can also 1)e used directly to split water, using conventional, low-temperature electrolysis (LTE). Hydrogen can also be produced with hybrid processes that use both process heat and electricity to generate hydrogen. An example of a hybrid process is high-temperature electrolysis (HTE), in which process heat is used to generate steam, which is then supplied to an electrolyzer to generate hydrogen. This process is of interest because the efficiency of electrolysis increases with temperature. Because of its high temperature capability, advanced stage of development relative to other high-temperature reactor concepts, and passive-safety features, the modular helium reactor (MHR) is well suited for producing hydrogen using nuclear energy. In this paper we investigate the coupling of the MHR to the S-I process, LTE, and HTE. These concepts are referred to as the H2-MHR. (author)

A literature review of coupled thermal-hydrologic-mechanical-chemical processes pertinent to the proposed high-level nuclear waste repository at Yucca Mountain

International Nuclear Information System (INIS)

Manteufel, R.D.; Ahola, M.P.; Turner, D.R.; Chowdhury, A.H.

1993-07-01

A literature review has been conducted to determine the state of knowledge available in the modeling of coupled thermal (T), hydrologic (H), mechanical (M), and chemical (C) processes relevant to the design and/or performance of the proposed high-level waste (HLW) repository at Yucca Mountain, Nevada. The review focuses on identifying coupling mechanisms between individual processes and assessing their importance (i.e., if the coupling is either important, potentially important, or negligible). The significance of considering THMC-coupled processes lies in whether or not the processes impact the design and/or performance objectives of the repository. A review, such as reported here, is useful in identifying which coupled effects will be important, hence which coupled effects will need to be investigated by the US Nuclear Regulatory Commission in order to assess the assumptions, data, analyses, and conclusions in the design and performance assessment of a geologic reposit''. Although this work stems from regulatory interest in the design of the geologic repository, it should be emphasized that the repository design implicitly considers all of the repository performance objectives, including those associated with the time after permanent closure. The scope of this review is considered beyond previous assessments in that it attempts with the current state-of-knowledge) to determine which couplings are important, and identify which computer codes are currently available to model coupled processes

A literature review of coupled thermal-hydrologic-mechanical-chemical processes pertinent to the proposed high-level nuclear waste repository at Yucca Mountain

Energy Technology Data Exchange (ETDEWEB)

Manteufel, R.D.; Ahola, M.P.; Turner, D.R.; Chowdhury, A.H. [Southwest Research Inst., San Antonio, TX (United States). Center for Nuclear Waste Regulatory Analyses

1993-07-01

A literature review has been conducted to determine the state of knowledge available in the modeling of coupled thermal (T), hydrologic (H), mechanical (M), and chemical (C) processes relevant to the design and/or performance of the proposed high-level waste (HLW) repository at Yucca Mountain, Nevada. The review focuses on identifying coupling mechanisms between individual processes and assessing their importance (i.e., if the coupling is either important, potentially important, or negligible). The significance of considering THMC-coupled processes lies in whether or not the processes impact the design and/or performance objectives of the repository. A review, such as reported here, is useful in identifying which coupled effects will be important, hence which coupled effects will need to be investigated by the US Nuclear Regulatory Commission in order to assess the assumptions, data, analyses, and conclusions in the design and performance assessment of a geologic reposit``. Although this work stems from regulatory interest in the design of the geologic repository, it should be emphasized that the repository design implicitly considers all of the repository performance objectives, including those associated with the time after permanent closure. The scope of this review is considered beyond previous assessments in that it attempts with the current state-of-knowledge) to determine which couplings are important, and identify which computer codes are currently available to model coupled processes.

Modeling of excavation induced coupled hydraulic-mechanical processes in claystone

Energy Technology Data Exchange (ETDEWEB)

Massmann, Jobst

2009-07-01

Concepts for the numerical modeling of excavation induced processes in claystone are investigated. The study has been motivated by the international discussion on the adequacy of claystone as a potential host rock for a final repository of radioactive waste. The processes, which could impact the safety of such a repository, are manifold and strongly interacting. Thus, a multiphysics approach is needed, regarding solid mechanics and fluid mechanics within a geological context. A coupled modeling concept is therefore indispensable. Based on observations and measurements at an argillaceous test site (the underground laboratory Tournemire, operated by the Institute of Radioprotection and Nuclear Safety, France) the modeling concept is developed. Two main processes constitute the basis of the applied model: deformation (linear elasticity considering damage) and fluid flow (unsaturated one-phase flow). Several coupling phenomena are considered: Terzaghi 's effective stress concept, mass conservation of the liquid in a deformable porous media, drying induced shrinkage, and a permeability which depends on deformation and damage. In addition, transversely isotropic material behavior is considered. The numerical simulations are done with the finite element code RockFlow, which is extended to include: an orthotropic non-linear shrinkage model, a continuum damage model, and an orthotropic permeability model. For these new methods the theory and a literature review are presented, followed by applications, which illustrate the capability to model excavation induced processes in principle. In a comprehensive case study, the modeling concept is used to simulate the response of the Tournemire argillite to excavation. The results are compared with observations and measurements of three different excavations (century old tunnel, two galleries excavated in 1996 and 2003). In summary, it can be concluded that the developed model concept provides a prediction of the excavation induced

Modeling of excavation induced coupled hydraulic-mechanical processes in claystone

International Nuclear Information System (INIS)

Massmann, Jobst

2009-01-01

Concepts for the numerical modeling of excavation induced processes in claystone are investigated. The study has been motivated by the international discussion on the adequacy of claystone as a potential host rock for a final repository of radioactive waste. The processes, which could impact the safety of such a repository, are manifold and strongly interacting. Thus, a multiphysics approach is needed, regarding solid mechanics and fluid mechanics within a geological context. A coupled modeling concept is therefore indispensable. Based on observations and measurements at an argillaceous test site (the underground laboratory Tournemire, operated by the Institute of Radioprotection and Nuclear Safety, France) the modeling concept is developed. Two main processes constitute the basis of the applied model: deformation (linear elasticity considering damage) and fluid flow (unsaturated one-phase flow). Several coupling phenomena are considered: Terzaghi 's effective stress concept, mass conservation of the liquid in a deformable porous media, drying induced shrinkage, and a permeability which depends on deformation and damage. In addition, transversely isotropic material behavior is considered. The numerical simulations are done with the finite element code RockFlow, which is extended to include: an orthotropic non-linear shrinkage model, a continuum damage model, and an orthotropic permeability model. For these new methods the theory and a literature review are presented, followed by applications, which illustrate the capability to model excavation induced processes in principle. In a comprehensive case study, the modeling concept is used to simulate the response of the Tournemire argillite to excavation. The results are compared with observations and measurements of three different excavations (century old tunnel, two galleries excavated in 1996 and 2003). In summary, it can be concluded that the developed model concept provides a prediction of the excavation induced

Modeling of excavation induced coupled hydraulic-mechanical processes in claystone

Energy Technology Data Exchange (ETDEWEB)

Massmann, Jobst

2009-07-01

Concepts for the numerical modeling of excavation induced processes in claystone are investigated. The study has been motivated by the international discussion on the adequacy of claystone as a potential host rock for a final repository of radioactive waste. The processes, which could impact the safety of such a repository, are manifold and strongly interacting. Thus, a multiphysics approach is needed, regarding solid mechanics and fluid mechanics within a geological context. A coupled modeling concept is therefore indispensable. Based on observations and measurements at an argillaceous test site (the underground laboratory Tournemire, operated by the Institute of Radioprotection and Nuclear Safety, France) the modeling concept is developed. Two main processes constitute the basis of the applied model: deformation (linear elasticity considering damage) and fluid flow (unsaturated one-phase flow). Several coupling phenomena are considered: Terzaghi 's effective stress concept, mass conservation of the liquid in a deformable porous media, drying induced shrinkage, and a permeability which depends on deformation and damage. In addition, transversely isotropic material behavior is considered. The numerical simulations are done with the finite element code RockFlow, which is extended to include: an orthotropic non-linear shrinkage model, a continuum damage model, and an orthotropic permeability model. For these new methods the theory and a literature review are presented, followed by applications, which illustrate the capability to model excavation induced processes in principle. In a comprehensive case study, the modeling concept is used to simulate the response of the Tournemire argillite to excavation. The results are compared with observations and measurements of three different excavations (century old tunnel, two galleries excavated in 1996 and 2003). In summary, it can be concluded that the developed model concept provides a prediction of the excavation

A General Strategy for Nanohybrids Synthesis via Coupled Competitive Reactions Controlled in a Hybrid Process

OpenAIRE

Wang, Rongming; Yang, Wantai; Song, Yuanjun; Shen, Xiaomiao; Wang, Junmei; Zhong, Xiaodi; Li, Shuai; Song, Yujun

2015-01-01

A new methodology based on core alloying and shell gradient-doping are developed for the synthesis of nanohybrids, realized by coupled competitive reactions, or sequenced reducing-nucleation and co-precipitation reaction of mixed metal salts in a microfluidic and batch-cooling process. The latent time of nucleation and the growth of nanohybrids can be well controlled due to the formation of controllable intermediates in the coupled competitive reactions. Thus, spatiotemporal-resolved synthesi...

Process research on Emotionally Focused Therapy (EFT) for couples: linking theory to practice.

Science.gov (United States)

Greenman, Paul S; Johnson, Susan M

2013-03-01

The focus of this article is on the link among theory, process, and outcome in the practice of Emotionally Focused Therapy (EFT) for couples. We describe the EFT model of change and the EFT perspective on adult love as the reflection of underlying attachment processes. We outline the manner in which theory and research inform EFT interventions. This leads into a detailed review of the literature on the processes of change in EFT. We highlight the client responses and therapist operations that have emerged from process research and their relation to treatment outcomes. We discuss the implications of this body of research for clinical practice and training. © FPI, Inc.

Development of the CHEMTARD coupled process simulator for use in radiological assessment

International Nuclear Information System (INIS)

Liew, S.K.; Read, D.

1987-12-01

This report describes features of CHEMTARD (Chemical Transport Adsorption Redox and Decay); a directly-coupled chemical transport code, developed to aid the DOE in carrying out post-closure radiological risk assessments. The program is based on the Lawrence Berkeley code, CHEMTRN, and simulates the one-dimensional transport of aqueous chemical species by advection and/or diffusion while accounting for phase transfer by reversible precipitation-dissolution, ion-exchange or surface adsorption. New models for radioactive decay, oxidation-reduction reactions, flexible boundary conditions and multi-layered transport have significantly enhanced the ability of the code to perform coupled process calculations. Although originally developed for studies involving shallow disposal of low level wastes, the models contained in CHEMTARD are sufficiently general to allow thermodynamic treatment of chemical transport for porous flow through all saturated aquifer systems. (author)

Modelling coupled microbial processes in the subsurface: Model development, verification, evaluation and application

Science.gov (United States)

Masum, Shakil A.; Thomas, Hywel R.

2018-06-01

To study subsurface microbial processes, a coupled model which has been developed within a Thermal-Hydraulic-Chemical-Mechanical (THCM) framework is presented. The work presented here, focuses on microbial transport, growth and decay mechanisms under the influence of multiphase flow and bio-geochemical reactions. In this paper, theoretical formulations and numerical implementations of the microbial model are presented. The model has been verified and also evaluated against relevant experimental results. Simulated results show that the microbial processes have been accurately implemented and their impacts on porous media properties can be predicted either qualitatively or quantitatively or both. The model has been applied to investigate biofilm growth in a sandstone core that is subjected to a two-phase flow and variable pH conditions. The results indicate that biofilm growth (if not limited by substrates) in a multiphase system largely depends on the hydraulic properties of the medium. When the change in porewater pH which occurred due to dissolution of carbon dioxide gas is considered, growth processes are affected. For the given parameter regime, it has been shown that the net biofilm growth is favoured by higher pH; whilst the processes are considerably retarded at lower pH values. The capabilities of the model to predict microbial respiration in a fully coupled multiphase flow condition and microbial fermentation leading to production of a gas phase are also demonstrated.

Fast and accurate inductance and coupling calculation for a multi-layer Nb process

International Nuclear Information System (INIS)

Fourie, Coenrad J; Takahashi, Akitomo; Yoshikawa, Nobuyuki

2015-01-01

Currently, fabrication processes for superconductive integrated circuits are moving to multiple wiring and shielding layers, some of which are placed below the main ground plane (GP) and device layers. The Advanced Industrial Science and Technology advanced process (ADP2) was the first such multi-layer Nb process with planarized passive transmission line and GP layers below the junction layer, and is at the time of writing still the most developed. This process allows complex circuit designs, and accurate inductance extraction helps to push the boundaries of the layouts possible. We show that the position of ground connections between ground layers influences the inductance of structures for which these GPs act as return path, and that this needs to be accounted for in modelling. However, due to the number of wiring layers and GPs, full layout modelling of large cells causes long calculation times. In this paper we discuss methods with which to reduce model size, and calibrate InductEx calculations using these methods against measured results. We show that model reduction followed by calibration results in fast calculation times while good accuracy is maintained. We also show that InductEx correctly handles coupling between conductors in a multi-layer layout, and how to model layouts to gauge unwanted coupling between power lines and single flux quantum electronics. (paper)

Modeling of coupled geochemical and transport processes: An overview

International Nuclear Information System (INIS)

Carnahan, C.L.

1989-10-01

Early coupled models associated with fluid flow and solute transport have been limited by assumed conditions of constant temperature, fully saturated fluid flow, and constant pore fluid velocity. Developments including coupling of chemical reactions to variable fields of temperature and fluid flow have generated new requirements for experimental data. As the capabilities of coupled models expand, needs are created for experimental data to be used for both input and validation. 25 refs

Up and down or down and up? The process of change in constructive couple behavior during Traditional and Integrative Behavioral Couple Therapy.

Science.gov (United States)

Sevier, Mia; Atkins, David C; Doss, Brian D; Christensen, Andrew

2015-01-01

Observed positive and negative spouse behavior during sessions of Traditional (TBCT) and Integrative Behavioral Couples Therapy (IBCT) were compared for couples with successful outcomes and their unsuccessful counterparts. One hundred and thirty-four married chronically and seriously distressed couples (on average in their forties and 80% Caucasian) were randomly assigned to TBCT or IBCT. Trained observers made ratings of 1224 segments from approximately 956 sessions sampled from the course of up to 26 sessions. Multilevel modeling was used to examine change over time. TBCT treatment responders demonstrated a boost-drop pattern, increasing in constructive behaviors early (more positive behaviors and less negative behaviors) but decreasing later. IBCT responders demonstrated an opposite, drop-boost pattern, decreasing in constructive behaviors early and increasing later. Patterns were significant for positive behaviors (p behaviors (p = .05). In both treatments, nonresponders showed a significant pattern of decline in positive and increase in negative behaviors over time, although a trend (p = .05) indicates that TBCT nonresponders initially declined in negative behaviors. This study helps clarify the different process of change in two behavioral couple therapies, which may assist in treatment development and provide a guide for therapists in considering behavioral markers of change during treatment. © 2013 American Association for Marriage and Family Therapy.

Scaling analysis of the coupled heat transfer process in the high-temperature gas-cooled reactor core

International Nuclear Information System (INIS)

Conklin, J.C.

1986-08-01

The differential equations representing the coupled heat transfer from the solid nuclear core components to the helium in the coolant channels are scaled in terms of representative quantities. This scaling process identifies the relative importance of the various terms of the coupled differential equations. The relative importance of these terms is then used to simplify the numerical solution of the coupled heat transfer for two bounding cases of full-power operation and depressurization from full-system operating pressure for the Fort St. Vrain High-Temperature Gas-Cooled Reactor. This analysis rigorously justifies the simplified system of equations used in the nuclear safety analysis effort at Oak Ridge National Laboratory

Hydromechanical coupling in fractured rock masses: mechanisms and processes of selected case studies

Science.gov (United States)

Zangerl, Christian

2015-04-01

Hydromechanical (HM) coupling in fractured rock play an important role when events including dam failures, landslides, surface subsidences due to water withdrawal or drainage, injection-induced earthquakes and others are analysed. Generally, hydromechanical coupling occurs when a rock mass contain interconnected pores and fractures which are filled with water and pore/fracture pressures evolves. In the on hand changes in the fluid pressure can lead to stress changes, deformations and failures of the rock mass. In the other hand rock mass stress changes and deformations can alter the hydraulic properties and fluid pressures of the rock mass. Herein well documented case studies focussing on surface subsidence due to water withdrawal, reversible deformations of large-scale valley flanks and failure as well as deformation processes of deep-seated rock slides in fractured rock masses are presented. Due to pore pressure variations HM coupling can lead to predominantly reversible rock mass deformations. Such processes can be considered by the theory of poroelasticity. Surface subsidence reaching magnitudes of few centimetres and are caused by water drainage into deep tunnels are phenomenas which can be assigned to processes of poroelasticity. Recently, particular focus was given on large tunnelling projects to monitor and predict surface subsidence in fractured rock mass in oder to avoid damage of surface structures such as dams of large reservoirs. It was found that surface subsidence due to tunnel drainage can adversely effect infrastructure when pore pressure drawdown is sufficiently large and spatially extended and differential displacements which can be amplified due to topographical effects e.g. valley closure are occurring. Reversible surface deformations were also ascertained on large mountain slopes and summits with the help of precise deformation measurements i.e. permanent GPS or episodic levelling/tacheometric methods. These reversible deformations are often

A network model shows the importance of coupled processes in the microbial N cycle in the Cape Fear River Estuary

Science.gov (United States)

Hines, David E.; Lisa, Jessica A.; Song, Bongkeun; Tobias, Craig R.; Borrett, Stuart R.

2012-06-01

Estuaries serve important ecological and economic functions including habitat provision and the removal of nutrients. Eutrophication can overwhelm the nutrient removal capacity of estuaries and poses a widely recognized threat to the health and function of these ecosystems. Denitrification and anaerobic ammonium oxidation (anammox) are microbial processes responsible for the removal of fixed nitrogen and diminish the effects of eutrophication. Both of these microbial removal processes can be influenced by direct inputs of dissolved inorganic nitrogen substrates or supported by microbial interactions with other nitrogen transforming pathways such as nitrification and dissimilatory nitrate reduction to ammonium (DNRA). The coupling of nitrogen removal pathways to other transformation pathways facilitates the removal of some forms of inorganic nitrogen; however, differentiating between direct and coupled nitrogen removal is difficult. Network modeling provides a tool to examine interactions among microbial nitrogen cycling processes and to determine the within-system history of nitrogen involved in denitrification and anammox. To examine the coupling of nitrogen cycling processes, we built a nitrogen budget mass balance network model in two adjacent 1 cm3 sections of bottom water and sediment in the oligohaline portion of the Cape Fear River Estuary, NC, USA. Pathway, flow, and environ ecological network analyses were conducted to characterize the organization of nitrogen flow in the estuary and to estimate the coupling of nitrification to denitrification and of nitrification and DNRA to anammox. Centrality analysis indicated NH4+ is the most important form of nitrogen involved in removal processes. The model analysis further suggested that direct denitrification and coupled nitrification-denitrification had similar contributions to nitrogen removal while direct anammox was dominant to coupled forms of anammox. Finally, results also indicated that partial

A small floating seawater desalination plant using a nuclear heating reactor coupled with the MED process

International Nuclear Information System (INIS)

Dong Duo; Wu Shaorong; Zhang Dafang; Wu Zongxin

1997-01-01

A small floating seawater desalination plant using a nuclear heating reactor coupled with a multi-effect distillation (MED) process was designed by the Institute of Nuclear Energy Technology, Tsinghua University of China. It was intended to supply potable water to remove coastal areas or islands where both fresh water and energy are severely lacking, and also to serve as a demonstration and training facility. The design of a small floating plant coupled two proven technologies in the cogeneration mode: a nuclear heating reactor (NHR-10), with inherent, passive safety features based on NHR-5 experience, and a low temperature MED process. The secondary loop was designed as a safety barrier between the primary loop and the steam loop. With a 10 MW(th) heating reactor, the floating plant could provide 4,000 m 3 /d of potable water and 750 kW of electricity. The design concept and parameters, safety features, coupling scheme and floating plant layout are presented in the paper. (author). 3 refs, 4 figs, 3 tabs

Ocean-Atmosphere Coupling Processes Affecting Predictability in the Climate System

Science.gov (United States)

Miller, A. J.; Subramanian, A. C.; Seo, H.; Eliashiv, J. D.

2017-12-01

Predictions of the ocean and atmosphere are often sensitive to coupling at the air-sea interface in ways that depend on the temporal and spatial scales of the target fields. We will discuss several aspects of these types of coupled interactions including oceanic and atmospheric forecast applications. For oceanic mesoscale eddies, the coupling can influence the energetics of the oceanic flow itself. For Madden-Julian Oscillation onset, the coupling timestep should resolve the diurnal cycle to properly raise time-mean SST and latent heat flux prior to deep convection. For Atmospheric River events, the evolving SST field can alter the trajectory and intensity of precipitation anomalies along the California coast. Improvements in predictions will also rely on identifying and alleviating sources of biases in the climate states of the coupled system. Surprisingly, forecast skill can also be improved by enhancing stochastic variability in the atmospheric component of coupled models as found in a multiscale ensemble modeling approach.

DECOVALEX III PROJECT. Mathematical Models of Coupled Thermal-Hydro-Mechanical Processes for Nuclear Waste Repositories. Executive Summary

Energy Technology Data Exchange (ETDEWEB)

Jing, L.; Stephansson, O. [Royal Inst. of Technology, Stockholm (Sweden). Engineering Geology; Tsang, C.F. [Lawrence Berkely National Laboratory, Berkeley, CA (United States). Earth Science Div.; Mayor, J.C. [ENRESA, Madrid (Spain); Kautzky, F. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden)] (eds.)

2005-02-15

DECOVALEX is an international consortium of governmental agencies associated with the disposal of high-level nuclear waste in a number of countries. The consortium's mission is the DEvelopment of COupled models and their VALidation against EXperiments. Hence the acronym/name DECOVALEX. Currently, agencies from Canada, Finland, France, Germany, Japan, Spain, Switzerland, Sweden, United Kingdom, and the United States are in DECOVALEX. Emplacement of nuclear waste in a repository in geologic media causes a number of physical processes to be intensified in the surrounding rock mass due to the decay heat from the waste. The four main processes of concern are thermal, hydrological, mechanical and chemical. Interactions or coupling between these heat-driven processes must be taken into account in modeling the performance of the repository for such modeling to be meaningful and reliable. DECOVALEX III is organized around four tasks. The FEBEX (Full-scale Engineered Barriers EXperiment) in situ experiment being conducted at the Grimsel site in Switzerland is to be simulated and analyzed in Task 1. Task 2, centered around the Drift Scale Test (DST) at Yucca Mountain in Nevada, USA, has several sub-tasks (Task 2A, Task 2B, Task 2C and Task 2D) to investigate a number of the coupled processes in the DST. Task 3 studies three benchmark problems: a) the effects of thermal-hydrologic-mechanical (THM) coupling on the performance of the near-field of a nuclear waste repository (BMT1); b) the effect of upscaling THM processes on the results of performance assessment (BMT2); and c) the effect of glaciation on rock mass behavior (BMT3). Task 4 is on the direct application of THM coupled process modeling in the performance assessment of nuclear waste repositories in geologic media. This executive summary presents the motivation, structure, objectives, approaches, and the highlights of the main achievements and outstanding issues of the tasks studied in the DECOVALEX III project

DECOVALEX III PROJECT. Mathematical Models of Coupled Thermal-Hydro-Mechanical Processes for Nuclear Waste Repositories. Executive Summary

International Nuclear Information System (INIS)

Jing, L.; Stephansson, O.; Kautzky, F.

2005-02-01

DECOVALEX is an international consortium of governmental agencies associated with the disposal of high-level nuclear waste in a number of countries. The consortium's mission is the DEvelopment of COupled models and their VALidation against EXperiments. Hence the acronym/name DECOVALEX. Currently, agencies from Canada, Finland, France, Germany, Japan, Spain, Switzerland, Sweden, United Kingdom, and the United States are in DECOVALEX. Emplacement of nuclear waste in a repository in geologic media causes a number of physical processes to be intensified in the surrounding rock mass due to the decay heat from the waste. The four main processes of concern are thermal, hydrological, mechanical and chemical. Interactions or coupling between these heat-driven processes must be taken into account in modeling the performance of the repository for such modeling to be meaningful and reliable. DECOVALEX III is organized around four tasks. The FEBEX (Full-scale Engineered Barriers EXperiment) in situ experiment being conducted at the Grimsel site in Switzerland is to be simulated and analyzed in Task 1. Task 2, centered around the Drift Scale Test (DST) at Yucca Mountain in Nevada, USA, has several sub-tasks (Task 2A, Task 2B, Task 2C and Task 2D) to investigate a number of the coupled processes in the DST. Task 3 studies three benchmark problems: a) the effects of thermal-hydrologic-mechanical (THM) coupling on the performance of the near-field of a nuclear waste repository (BMT1); b) the effect of upscaling THM processes on the results of performance assessment (BMT2); and c) the effect of glaciation on rock mass behavior (BMT3). Task 4 is on the direct application of THM coupled process modeling in the performance assessment of nuclear waste repositories in geologic media. This executive summary presents the motivation, structure, objectives, approaches, and the highlights of the main achievements and outstanding issues of the tasks studied in the DECOVALEX III project. The

Effect of thermo-coupled processes on the behaviour of a clay barrier submitted to heating and hydration

Directory of Open Access Journals (Sweden)

Marcelo Sánchez

2010-03-01

Full Text Available The storage of high level radioactive waste is still an unresolved problem of the nuclear industry, being geological disposal the most favoured option and, naturally, the one requiring the strongest geo-mechanical input. Most conceptual designs for the deep geological disposal of nuclear waste envisage placing the canisters containing the waste in horizontal drifts or vertical boreholes. The empty space surrounding the canisters is filled by an engineered barrier often made up of compacted swelling clay. Inthebarrierandthenearfield,significantthermo-hydro-mechanical(THM phenomena take place that interact in a complex way. A good understanding of THM issues is, therefore, necessary to ensure a correct performance of engineered barriers and seals. The conditions of the bentonite in an engineered barrier for high-level radioactive waste disposal are being simulated in a mock-up heating test at almost scale, at the premises of CIEMAT in Madrid. The evolution of the main Thermo-Hydro-Mechanical (THM variables of this test are analysed in this paper by using a fully coupled THM formulation and the corresponding finite element code. Special emphasis has been placed on the study of the effect of thermo-osmotic flow in the hydration of the clay barrier at an advanced staged of the experiment.O armazenamento de rejeitos altamente radioativos é ainda um problema em aberto na área de engenharia nuclear sendo os sítios geológicos ainda a opção mais favorável e naturalmente aquela que demanda maior conhecimento na área de geomecânica. A maioria dos projetos conceituais de armazenamento do lixo nuclear objetiva a alocação de cilindros que contêm os rejeitos em poços verticais ou horizontais. O espaço vazio que circunda os cilindros é preenchido por uma barreirade engenharia na maioria dos casos composta por uma argila expansiva. Na barreira e na vizinhança fenômenos significativos de acoplamento termo-hidro-mecânico(THM tomam lugar e

Inductively coupled hydrogen plasma processing of AZO thin films for heterojunction solar cell applications

International Nuclear Information System (INIS)

Zhou, H.P.; Xu, S.; Zhao, Z.; Xiang, Y.

2014-01-01

Highlights: • A high-density plasma reactor of inductively coupled plasma source is used in this work. • The conductivity and transmittance can be enhanced simultaneously in the hydrogen process. • The formation of additional donors and passivation due to the hydrogen plasma processing. • The photovoltaic improvement due to the improved AZO layer and hetero-interface quality in the solar cells. - Abstract: Al-doped ZnO (AZO) thin films deposited by means of RF magnetron sputtering were processed in a low frequency inductively coupled plasma of H 2 , aiming at heterojunction (HJ) solar cell applications. A variety of characterization results show that the hydrogen plasma processing exerts a significant influence on the microstructures, electrical and optical properties of the AZO films. The incorporation of hydrogen under the optimum treatment simultaneously promoted the transmittance and conductivity due to the hydrogen associated passivation effect on the native defects and the formation of shallow donors in the films, respectively. A p-type c-Si based HJ solar cell with a front AZO contact was also treated in as-generated non-equilibrium hydrogen plasma and the photovoltaic performance of the solar cell was prominently improved. The underlying mechanism was discussed in terms of the beneficial impacts of high-density hydrogen plasma on the properties of AZO itself and the hetero-interfaces involved in the HJ structure (interface defect and energy band configuration)

Structural factors controlling inter-plate coupling and earthquake rupture process

Science.gov (United States)

Kodaira, S.

2007-05-01

Recent availability of a large number of ocean bottom seismographs (OBSs), a large volume of air-gun array and a long streamer cable for academics provide several new findings of lithospheric scale structures in subduction seismogenic zones. JAMSTEC has acquired long-offset seismic data using a super-densely deploy OBS (i.e. 1 - 5 km spacing OBSs along 100 - 500 km long profiles) in the Nankai seismogeinc zone, SW. Japan, since 1999. Long-offset multichannel seismic (MCS) data by a two-ship experiment, as well as conventional 2D MCS data, have been also acquired at a part of the profiles. Some of those profiles have been designed as combined onshore - offshore profiles for imaging a land-ocean transition zone. One of the most striking findings is an image of several scales of subducted seamounts/ridges in the Nankai trough seismogenic zone. We detected the subducted seamount/ridges, which are 50 - 100 km wide, distributing from near trough axis to ~ 40 km deep beneath the Japanese island. From a point of seismogenic process, an important aspect is that those structures are strongly correlated with slip zones of magnitude 8-class earthquakes, i.e.; subducted seamounts/ridge control the rupture propagations. Moreover, the most recent seismic study crossing the segmentation boundary between M=8 class earthquakes detected a high seismic velocity body forming a strongly coupled patch at the segmentation boundary. The numerical simulation incorporating all those structures explained the historic rupture patterns, and shows the occurrence of a giant earthquake along the entire Nankai trough, a distance of over 600 km long (Mw=8.7). The growth processes of a rupture revealed from the simulation are; 1) prior to the giant earthquake, a small slow event (or earthquake) occurs near the segmentation boundary, 2) this accelerates a very slow slip (slower than the plate convergent rate), at the strong patch, which reduces a degree of coupling, 3) then a rupture easily propagates

Reactive Transport and Coupled THM Processes in Engineering Barrier Systems (EBS)

International Nuclear Information System (INIS)

Steefel, Carl; Rutqvist, Jonny; Tsang, Chin-Fu; Liu, Hui-Hai; Sonnenthal, Eric; Houseworth, Jim; Birkholzer, Jens

2010-01-01

Geological repositories for disposal of high-level nuclear wastes generally rely on a multi-barrier system to isolate radioactive wastes from the biosphere. The multi-barrier system typically consists of a natural barrier system, including repository host rock and its surrounding subsurface environment, and an engineering barrier system (EBS). EBS represents the man-made, engineered materials placed within a repository, including the waste form, waste canisters, buffer materials, backfill and seals (OECD, 2003). EBS plays a significant role in the containment and long-term retardation of radionuclide release. EBS is involved in complex thermal, hydrogeological, mechanical, chemical and biological processes, such as heat release due to radionuclide decay, multiphase flow (including gas release due to canister corrosion), swelling of buffer materials, radionuclide diffusive transport, waste dissolution and chemical reactions. All these processes are related to each other. An in-depth understanding of these coupled processes is critical for the performance assessment (PA) for EBS and the entire repository. Within the EBS group of Used Fuel Disposition (UFD) Campaign, LBNL is currently focused on (1) thermal-hydraulic-mechanical-chemical (THMC) processes in buffer materials (bentonite) and (2) diffusive transport in EBS associated with clay host rock, with a long-term goal to develop a full understanding of (and needed modeling capabilities to simulate) impacts of coupled processes on radionuclide transport in different components of EBS, as well as the interaction between near-field host rock (e.g., clay) and EBS and how they effect radionuclide release. This final report documents the progress that LBNL has made in its focus areas. Specifically, Section 2 summarizes progress on literature review for THMC processes and reactive-diffusive radionuclide transport in bentonite. The literature review provides a picture of the state-of-the-art of the relevant research areas

Reactive Transport and Coupled THM Processes in Engineering Barrier Systems (EBS)

Energy Technology Data Exchange (ETDEWEB)

Steefel, Carl; Rutqvist, Jonny; Tsang, Chin-Fu; Liu, Hui-Hai; Sonnenthal, Eric; Houseworth, Jim; Birkholzer, Jens

2010-08-31

Geological repositories for disposal of high-level nuclear wastes generally rely on a multi-barrier system to isolate radioactive wastes from the biosphere. The multi-barrier system typically consists of a natural barrier system, including repository host rock and its surrounding subsurface environment, and an engineering barrier system (EBS). EBS represents the man-made, engineered materials placed within a repository, including the waste form, waste canisters, buffer materials, backfill and seals (OECD, 2003). EBS plays a significant role in the containment and long-term retardation of radionuclide release. EBS is involved in complex thermal, hydrogeological, mechanical, chemical and biological processes, such as heat release due to radionuclide decay, multiphase flow (including gas release due to canister corrosion), swelling of buffer materials, radionuclide diffusive transport, waste dissolution and chemical reactions. All these processes are related to each other. An in-depth understanding of these coupled processes is critical for the performance assessment (PA) for EBS and the entire repository. Within the EBS group of Used Fuel Disposition (UFD) Campaign, LBNL is currently focused on (1) thermal-hydraulic-mechanical-chemical (THMC) processes in buffer materials (bentonite) and (2) diffusive transport in EBS associated with clay host rock, with a long-term goal to develop a full understanding of (and needed modeling capabilities to simulate) impacts of coupled processes on radionuclide transport in different components of EBS, as well as the interaction between near-field host rock (e.g., clay) and EBS and how they effect radionuclide release. This final report documents the progress that LBNL has made in its focus areas. Specifically, Section 2 summarizes progress on literature review for THMC processes and reactive-diffusive radionuclide transport in bentonite. The literature review provides a picture of the state-of-the-art of the relevant research areas

3D numerical modeling of coupled phenomena in induced processes of heat treatment with malice

Directory of Open Access Journals (Sweden)

Triwong Peeteenut

2008-01-01

Full Text Available This paper describes a multi-method Malice package for three dimension coupled phenomena in induced processes of heat treatment by an algorithm weakly coupled with the Migen package integral method defining the electromagnetic model and the Flux-Expert package finite element method defining the thermal model. The integral method is well suited to inductive systems undergoing sinusoidal excitation at midrange or high frequency. The unknowns of both models are current density, scalar potential and temperature. Joule power in the electromagnetic model is generated by Eddy currents. It becomes the heat source in the thermal model.

Si-compatible cleaning process for graphene using low-density inductively coupled plasma.

Science.gov (United States)

Lim, Yeong-Dae; Lee, Dae-Yeong; Shen, Tian-Zi; Ra, Chang-Ho; Choi, Jae-Young; Yoo, Won Jong

2012-05-22

We report a novel cleaning technique for few-layer graphene (FLG) by using inductively coupled plasma (ICP) of Ar with an extremely low plasma density of 3.5 × 10(8) cm(-3). It is known that conventional capacitively coupled plasma (CCP) treatments destroy the planar symmetry of FLG, giving rise to the generation of defects. However, ICP treatment with extremely low plasma density is able to remove polymer resist residues from FLG within 3 min at a room temperature of 300 K while retaining the carbon sp(2)-bonding of FLG. It is found that the carrier mobility and charge neutrality point of FLG are restored to their pristine defect-free state after the ICP treatment. Considering the application of graphene to silicon-based electronic devices, such a cleaning method can replace thermal vacuum annealing, electrical current annealing, and wet-chemical treatment due to its advantages of being a low-temperature, large-area, high-throughput, and Si-compatible process.

Phenol wastewater remediation: advanced oxidation processes coupled to a biological treatment.

Science.gov (United States)

Rubalcaba, A; Suárez-Ojeda, M E; Stüber, F; Fortuny, A; Bengoa, C; Metcalfe, I; Font, J; Carrera, J; Fabregat, A

2007-01-01

Nowadays, there are increasingly stringent regulations requiring more and more treatment of industrial effluents to generate product waters which could be easily reused or disposed of to the environment without any harmful effects. Therefore, different advanced oxidation processes were investigated as suitable precursors for the biological treatment of industrial effluents containing phenol. Wet air oxidation and Fenton process were tested batch wise, while catalytic wet air oxidation and H2O2-promoted catalytic wet air oxidation processes were studied in a trickle bed reactor, the last two using over activated carbon as catalyst. Effluent characterisation was made by means of substrate conversion (using high liquid performance chromatography), chemical oxygen demand and total organic carbon. Biodegradation parameters (i.e. maximum oxygen uptake rate and oxygen consumption) were obtained from respirometric tests using activated sludge from an urban biological wastewater treatment plant (WWTP). The main goal was to find the proper conditions in terms of biodegradability enhancement, so that these phenolic effluents could be successfully treated in an urban biological WWTP. Results show promising research ways for the development of efficient coupled processes for the treatment of wastewater containing toxic or biologically non-degradable compounds.

EUROPAIRS: The European project on coupling of High Temperature Reactors with industrial processes

International Nuclear Information System (INIS)

Angulo, C.; Bogusch, E.; Bredimas, A.; Delannay, N.; Viala, C.; Ruer, J.; Muguerra, Ph.; Sibaud, E.; Chauvet, V.; Hittner, D.; Fütterer, M.A.; Groot, S. de; Lensa, W. von; Verfondern, K.; Moron, R.; Baudrand, O.; Griffay, G.; Baaten, A.; Segurado-Gimenez, J.

2012-01-01

Developers of High Temperature Reactors (HTR) worldwide acknowledge that the main asset for market breakthrough is its unique ability to address growing needs for industrial cogeneration of heat and power (CHP) owing to its high operating temperature and flexibility, adapted power level, modularity and robust safety features. A strong alliance between nuclear and process heat user industries is a necessity for developing such a nuclear system for the conventional process heat market, just as the electro-nuclear development required a close partnership with utilities. Initiating such an alliance is one of the objectives of the EUROPAIRS project ( (www.europairs.eu)) presently on-going in the frame of the Euratom 7th Framework Programme (FP7). Although small and of short duration (21 months), EUROPAIRS is of strategic importance: it generates the boundary conditions for rapid demonstration of collocating HTR with industrial processes as proposed by the European High Temperature Reactor Technology Network (HTR-TN). This paper presents the main goals, the organization and the working approach of EUROPAIRS. It also presents the status of the viability assessment studies for coupling HTR with industrial end-user systems as one of the main pillars of the project. The main goal of the viability assessment is to identify developments required to remove the last technological and licensing barriers for a viable coupling scheme. The study is expected to result in guidelines for directing the choice of an industrial scale prototype.

EUROPAIRS: The European project on coupling of High Temperature Reactors with industrial processes

Energy Technology Data Exchange (ETDEWEB)

Angulo, C., E-mail: carmen.angulo@gdfsuez.com [Tractebel Engineering S.A. (GDF SUEZ), Avenue Ariane 7, 1200 Brussels (Belgium); Bogusch, E. [AREVA NP GmbH, Paul-Gossen-Strasse 100, 91052 Erlangen (Germany); Bredimas, A. [LGI Consulting, 37 rue de la Grange aux Belles, 75010 Paris (France); Delannay, N. [Tractebel Engineering S.A. (GDF SUEZ), Avenue Ariane 7, 1200 Brussels (Belgium); Viala, C. [AREVA NP SAS, 10 rue Juliette Recamier, 69456 Lyon Cedex 06 (France); Ruer, J.; Muguerra, Ph.; Sibaud, E. [SAIPEM S.A., 1/7 Avenue San Fernando, 78884 Saint Quentin en Yvelines Cedex (France); Chauvet, V. [LGI Consulting, 37 rue de la Grange aux Belles, 75010 Paris (France); Hittner, D. [AREVA NP Inc., 3315 Old Forest Road, Lynchburg, VA 24501 (United States); Fuetterer, M.A. [European Commission, Joint Research Centre, 1755ZG Petten (Netherlands); Groot, S. de [Nuclear Research and Consultancy Group, 1755ZG Petten (Netherlands); Lensa, W. von; Verfondern, K. [Forschungszentrum Juelich GmbH, Leo-Brandt-Strasse,52425 Juelich (Germany); Moron, R. [Solvay SA, rue du Prince Albert 33, 1050 Brussels (Belgium); Baudrand, O. [Institut de Radioprotection et de Surete Nucleaire (IRSN), BP 17, 92262 Fontenay-aux-Roses cedex (France); Griffay, G. [Arcelor Mittal Maizieres Research SA, rue Luigi Cherubini 1A5, 39200 Saint Denis (France); Baaten, A. [USG/Baaten Energy Consulting, Burgermeester-Ceulen-Straat 78, 6212CT Maastricht (Netherlands); Segurado-Gimenez, J. [Tractebel Engineering S.A. (GDF SUEZ), Avenue Ariane 7, 1200 Brussels (Belgium)

2012-10-15

Developers of High Temperature Reactors (HTR) worldwide acknowledge that the main asset for market breakthrough is its unique ability to address growing needs for industrial cogeneration of heat and power (CHP) owing to its high operating temperature and flexibility, adapted power level, modularity and robust safety features. A strong alliance between nuclear and process heat user industries is a necessity for developing such a nuclear system for the conventional process heat market, just as the electro-nuclear development required a close partnership with utilities. Initiating such an alliance is one of the objectives of the EUROPAIRS project ( (www.europairs.eu)) presently on-going in the frame of the Euratom 7th Framework Programme (FP7). Although small and of short duration (21 months), EUROPAIRS is of strategic importance: it generates the boundary conditions for rapid demonstration of collocating HTR with industrial processes as proposed by the European High Temperature Reactor Technology Network (HTR-TN). This paper presents the main goals, the organization and the working approach of EUROPAIRS. It also presents the status of the viability assessment studies for coupling HTR with industrial end-user systems as one of the main pillars of the project. The main goal of the viability assessment is to identify developments required to remove the last technological and licensing barriers for a viable coupling scheme. The study is expected to result in guidelines for directing the choice of an industrial scale prototype.

Modeling and Simulation of the Sulfur-Iodine Process Coupled to a Very High-Temperature Gas-Cooled Nuclear Reactor

International Nuclear Information System (INIS)

Shin, Youngjoon; Lee, Taehoon; Lee, Kiyoung; Kim, Minhwan

2015-01-01

Hydrogen produced from water using nuclear energy will avoid both the use of fossil fuel and CO 2 emission presumed to be the dominant reason for global warming. A thermo-chemical sulfur-iodine (SI) process coupled to a Very High Temperature Gas-Cooled Reactor(VHTR) is one of the most prospective hydrogen production methods that split water using nuclear energy because the SI process is suitable for large-scale hydrogen production without CO 2 emission. The dynamic simulation code to evaluate the start-up behavior of the chemical reactors placed on the secondary helium loop of the SI process has been developed and partially verified using the steady state values obtained from the Aspen Plus TM Code simulation. As the start-up dynamic simulation results of the SI process coupled to the IHX, which is one of components in the VHTR system, it is expected that the integrated secondary helium loop of the SI process can be successfully and safely approach the steady state condition

The decision-making process for breast reconstruction after cancer surgery: Representations of heterosexual couples in long-standing relationships.

Science.gov (United States)

Fasse, Léonor; Flahault, Cécile; Vioulac, Christel; Lamore, Kristopher; Van Wersch, Anna; Quintard, Bruno; Untas, Aurélie

2017-05-01

Most people deal with intrusive life events such as cancer and the care trajectory together with their intimate partners. To our knowledge, no research has studied the involvement of the partner in the decision-making process regarding breast reconstruction (BR) after cancer. This study aimed to gain a better understanding of the couples' decision-making process for BR in the cancer context and particularly to investigate the partners' involvement in this process. Eighteen participants (nine women who underwent a mastectomy following a first breast cancer and their intimate partners) took part in this study. We conducted semidirective interviews, and a general inductive approach was chosen to capture the representations of the couples. The women in the sample were aged between 33 and 66 years (M = 54, SD = 7.5) and their partner between 40 and 76 years (M = 59, SD = 11.6). The duration of their intimate relationship was on average 18 years (SD = 10.4; minimum = 4; maximum = 33). The analysis revealed 11 major themes. The two most salient ones were 'external influence' and 'implication of the partner'. The exploration of the subthemes revealed that the decision-making process is often reported as an interrelated experience by the couples and as a dyadic stressor. The partner's role is depicted as consultative and mostly supportive. These results provide new insights on the involvement of the partner in decision-making. Thus, it now seems crucial to develop a prospective study, which will help understand the progression of the decision-making process over time. Statement of contribution What is already known on this subject? Most people deal with intrusive life events such as cancer and the care trajectory together with their intimate partners. Shared decision-making between patients and physicians is now the 'gold standard' in Western Europe and the United States. However, in the context of breast reconstruction (BR) after cancer, factors guiding

Hybrid models for the simulation of microstructural evolution influenced by coupled, multiple physical processes

Energy Technology Data Exchange (ETDEWEB)

Tikare, Veena [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hernandez-Rivera, Efrain [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Madison, Jonathan D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Holm, Elizabeth Ann [Carnegie Mellon Univ., Pittsburgh, PA (United States); Patterson, Burton R. [Univ. of Florida, Gainesville, FL (United States). Dept. of Materials Science and Engineering; Homer, Eric R. [Brigham Young Univ., Provo, UT (United States). Dept. of Mechanical Engineering

2013-09-01

Most materials microstructural evolution processes progress with multiple processes occurring simultaneously. In this work, we have concentrated on the processes that are active in nuclear materials, in particular, nuclear fuels. These processes are coarsening, nucleation, differential diffusion, phase transformation, radiation-induced defect formation and swelling, often with temperature gradients present. All these couple and contribute to evolution that is unique to nuclear fuels and materials. Hybrid model that combines elements from the Potts Monte Carlo, phase-field models and others have been developed to address these multiple physical processes. These models are described and applied to several processes in this report. An important feature of the models developed are that they are coded as applications within SPPARKS, a Sandiadeveloped framework for simulation at the mesoscale of microstructural evolution processes by kinetic Monte Carlo methods. This makes these codes readily accessible and adaptable for future applications.

THM-coupled modeling of selected processes in argillaceous rock relevant to rock mechanics

International Nuclear Information System (INIS)

Czaikowski, Oliver

2012-01-01

Scientific investigations in European countries other than Germany concentrate not only on granite formations (Switzerland, Sweden) but also on argillaceous rock formations (France, Switzerland, Belgium) to assess their suitability as host and barrier rock for the final storage of radioactive waste. In Germany, rock salt has been under thorough study as a host rock over the past few decades. According to a study by the German Federal Institute for Geosciences and Natural Resources, however, not only salt deposits but also argillaceous rock deposits are available at relevant depths and of extensions in space which make final storage of high-level radioactive waste basically possible in Germany. Equally qualified findings about the suitability/unsuitability of non-saline rock formations require fundamental studies to be conducted nationally because of the comparatively low level of knowledge. The article presents basic analyses of coupled mechanical and hydraulic properties of argillaceous rock formations as host rock for a repository. The interaction of various processes is explained on the basis of knowledge derived from laboratory studies, and open problems are deduced. For modeling coupled processes, a simplified analytical computation method is proposed and compared with the results of numerical simulations, and the limits to its application are outlined. (orig.)

Finite-element simulations of coupling capacitances in capacitively coupled pixel detectors

CERN Document Server

AUTHOR|(SzGeCERN)755510

2017-01-01

Capacitively coupled hybrid silicon pixel-detector assemblies are under study for the vertex detector at the proposed future CLIC linear electron-positron collider. The assemblies consist of active CCPDv3 sensors, with 25 μm pixel pitch implemented in a 180 nm High- Voltage CMOS process, which are glued to the CLICpix readout ASIC, with the same pixel pitch and processed in a commercial 65 nm CMOS technology. The signal created in the silicon bulk of the active sensors passes a two-stage amplifier, in each pixel, and gets transferred as a voltage pulse to metal pads facing the readout chip (ROC). The coupling of the signal to the metal pads on the ROC side proceeds through the capacitors formed between the two chips by a thin layer of epoxy glue. The coupling strength and the amount of unwanted cross coupling to neighbouring pixels depends critically on the uniformity of the glue layer, its thickness and on the alignment precision during the flip-chip assembly process. Finite-element calculations of the coup...

Multiphasic fluid models and multicomponents reactive transport in porous media

International Nuclear Information System (INIS)

Juncosa, R.

2001-01-01

The design and construction of repositories for toxic waste, such as radioactive waste of medium and high activity, require tools, that will enable us to predict how the system will behave. The rational behind this Dissertation is based precisely on developing numerical models to study and predict coupled thermal, mechanical, hydrodynamic and geochemical behavior of clays intended to be used as engineered barriers in radioactive waste repository. In order to meet the requirements of the FEBEX Project (Full Scale Engineered Barriers Experiment) it was necessary to develop thermo-hydro-geochemical conceptual and numerical models (THG). For this purpose a THG code was developed to simulate and predict the THG behavior of the clay barrier. The code was created after considering two options. a) The development of a completely new code, or b) the coupling of existing codes. In this Dissertation we chose the second option, and developed a new program (FADES-CORE), which was obtained by using the FADES thermo-hydro-mechanical code (Navarro, 1997) and the CORE-LE code (Samper et al., 1998). This process entailed the modification of FADES, the addition of new subroutines for the calculation of solute transport, the modification of CORE-LE and the introduction of additional geochemical and transport processes. (Author)

Multiphasic fluid models and multicomponents reactive transport in porous media; Modelos de flujo multifasico no isotermo y de transporte reactivo multicomponente en medios porosos

Energy Technology Data Exchange (ETDEWEB)

Juncosa, R [Universidad Politecnica de Madrid (Spain)

2001-07-01

The design and construction of repositories for toxic waste, such as radioactive waste of medium and high activity, require tools, that will enable us to predict how the system will behave. The rational behind this Dissertation is based precisely on developing numerical models to study and predict coupled thermal, mechanical, hydrodynamic and geochemical behavior of clays intended to be used as engineered barriers in radioactive waste repository. In order to meet the requirements of the FEBEX Project (Full Scale Engineered Barriers Experiment) it was necessary to develop thermo-hydro-geochemical conceptual and numerical models (THG). For this purpose a THG code was developed to simulate and predict the THG behavior of the clay barrier. The code was created after considering two options. (a) The development of a completely new code, or (b) the coupling of existing codes. In this Dissertation we chose the second option, and developed a new program (FADES-CORE), which was obtained by using the FADES thermo-hydro-mechanical code (Navarro, 1997) and the CORE-LE code (Samper et al., 1998). This process entailed the modification of FADES, the addition of new subroutines for the calculation of solute transport, the modification of CORE-LE and the introduction of additional geochemical and transport processes. (Author)

Thermal hardening of saturated clays. Application to underground storage of radioactive wastes

International Nuclear Information System (INIS)

Picard, Jean-Marc

1994-01-01

Saturated clays submitted to constant mechanical loading and slow temperature increase frequently undergo irreversible contractions. This phenomena is described here by means of a change of plastic limits induced by temperature only, called thermal hardening. Constitutive laws adapted to this kind of plastic behaviour can be formulated within a general framework that satisfies thermodynamical principles. It shows that this coupling results from the presence of a latent heat during the isothermal hardening of plastic limits. A thermomechanical extension of Cam Clay model is then proposed and used in the analysis of laboratory thermomechanical tests performed on clay materials. Making use of tests already published, we show the adequacy of the concept of thermal hardening for clay behaviour. Some clay from deep geological formation considered for the disposal of radioactive waste exhibit thermal hardening in laboratory tests. The consequences for the underground storage facilities during the thermal loading created by the waste are investigated by means of in situ tests as well as numerical computation. The measurement around a heating probe buried in the clay mass demonstrate the significance of thermo-hydro-mechanical couplings. An accurate understanding of in situ measurements is achieved by means of numerical modeling in which the interaction between the various loading of the tests (excavation, pore pressure seepage, and heating) is carefully taken into account. Thermal hardening of the clay appears to be of little influence in these in situ tests. On the other hand, the magnitude of thermo-hydro-mechanical couplings observed in situ are higher than might have been expected from laboratory tests. A more accurate prediction is obtained if one takes into account the more stiffer behaviour of clays when they are subjected to small deformations. (authors)

Numerical study of laser-induced blast wave coupled with unsteady ionization processes

International Nuclear Information System (INIS)

Ogino, Y; Ohnishi, N; Sawada, K

2008-01-01

We present the results of the numerical simulation of laser-induced blast wave coupled with rate equations to clarify the unsteady property of ionization processes during pulse heating. From comparison with quasi-steady computations, the plasma region expands more widely, which is sustained by the inverse-bremsstrahlung since an ionization equilibrium does not establish at the front of the plasma region. The delayed relaxation leads to the rapid expansion of the driving plasma and enhances the energy conversion efficiency from a pulse heating laser to the blast wave

Coupled Thermo-Hydro-Mechanical-Chemical Modeling of Water Leak-Off Process during Hydraulic Fracturing in Shale Gas Reservoirs

Directory of Open Access Journals (Sweden)

Fei Wang

2017-11-01

Full Text Available The water leak-off during hydraulic fracturing in shale gas reservoirs is a complicated transport behavior involving thermal (T, hydrodynamic (H, mechanical (M and chemical (C processes. Although many leak-off models have been published, none of the models fully coupled the transient fluid flow modeling with heat transfer, chemical-potential equilibrium and natural-fracture dilation phenomena. In this paper, a coupled thermo-hydro-mechanical-chemical (THMC model based on non-equilibrium thermodynamics, hydrodynamics, thermo-poroelastic rock mechanics, and non-isothermal chemical-potential equations is presented to simulate the water leak-off process in shale gas reservoirs. The THMC model takes into account a triple-porosity medium, which includes hydraulic fractures, natural fractures and shale matrix. The leak-off simulation with the THMC model involves all the important processes in this triple-porosity medium, including: (1 water transport driven by hydraulic, capillary, chemical and thermal osmotic convections; (2 gas transport induced by both hydraulic pressure driven convection and adsorption; (3 heat transport driven by thermal convection and conduction; and (4 natural-fracture dilation considered as a thermo-poroelastic rock deformation. The fluid and heat transport, coupled with rock deformation, are described by a set of partial differential equations resulting from the conservation of mass, momentum, and energy. The semi-implicit finite-difference algorithm is proposed to solve these equations. The evolution of pressure, temperature, saturation and salinity profiles of hydraulic fractures, natural fractures and matrix is calculated, revealing the multi-field coupled water leak-off process in shale gas reservoirs. The influences of hydraulic pressure, natural-fracture dilation, chemical osmosis and thermal osmosis on water leak-off are investigated. Results from this study are expected to provide a better understanding of the

Coupled Inverse Fluidized Bed Bioreactor with Advanced Oxidation Processes for Treatment of Vinasse

Directory of Open Access Journals (Sweden)

Karla E. Campos Díaz

2017-11-01

Full Text Available Vinasse is the wastewater generated from ethanol distillation; it is characterized by high levels of organic and inorganic matter, high exit temperature, dissolved salts and low pH. In this work the treatment of undiluted vinasse was achieved using sequentially-coupled biological and advanced oxidation processes. The initial characterization of vinasse showed a high Chemical Oxygen Demand (COD, 32 kg m-3, high Total Organic Carbon (TOC, 24.5 kg m-3 and low pH (2.5. The first stage of the biological treatment of the vinasse was carried out in an inverse fluidized bed bioreactor with a microbial consortium using polypropylene as support material. The fluidized bed bioreactor was kept at a constant temperature (37 ± 1ºC and pH (6.0 ± 0.5 for 90 days. After the biological process, the vinasse was continuously fed to the photoreactor using a peristaltic pump 2.8 × 10-3 kg of FeSO4•7H2O were added to the vinasse and allowed to dissolve in the dark for five minutes; after this time, 15.3 m3 of hydrogen peroxide (H2O2 (30% w/w were added, and subsequently, the UV radiation was allowed to reach the photoreactor to treat the effluent for 3600 s at pH = 3. Results showed that the maximum organic matter removed using the biological process, measured as COD, was 80% after 90 days. Additionally, 88% of COD removal was achieved using the photo-assisted Fenton oxidation. The overall COD removal after the sequentially-coupled processes reached a value as low as 0.194 kg m-3, achieving over 99% of COD removal as well as complete TOC removal.

A MODELING AND SIMULATION LANGUAGE FOR BIOLOGICAL CELLS WITH COUPLED MECHANICAL AND CHEMICAL PROCESSES.

Science.gov (United States)

Somogyi, Endre; Glazier, James A

2017-04-01

Biological cells are the prototypical example of active matter. Cells sense and respond to mechanical, chemical and electrical environmental stimuli with a range of behaviors, including dynamic changes in morphology and mechanical properties, chemical uptake and secretion, cell differentiation, proliferation, death, and migration. Modeling and simulation of such dynamic phenomena poses a number of computational challenges. A modeling language describing cellular dynamics must naturally represent complex intra and extra-cellular spatial structures and coupled mechanical, chemical and electrical processes. Domain experts will find a modeling language most useful when it is based on concepts, terms and principles native to the problem domain. A compiler must then be able to generate an executable model from this physically motivated description. Finally, an executable model must efficiently calculate the time evolution of such dynamic and inhomogeneous phenomena. We present a spatial hybrid systems modeling language, compiler and mesh-free Lagrangian based simulation engine which will enable domain experts to define models using natural, biologically motivated constructs and to simulate time evolution of coupled cellular, mechanical and chemical processes acting on a time varying number of cells and their environment.

Analysis of the deep rolling process on turbine blades using the FEM/BEM-coupling

International Nuclear Information System (INIS)

Baecker, V; Klocke, F; Wegner, H; Timmer, A; Grzhibovskis, R; Rjasanow, S

2010-01-01

Highly stressed components of aircraft engines, like turbine blades, have to satisfy stringent requirements regarding durability and reliability. The induction of compressive stresses and strain hardening in their surface layer has proven as a promising method to significantly increase their fatigue resistance. The required surface layer properties can be achieved by deep rolling. The determination of optimal process parameters still requires elaborate experimental set-up and subsequent time- and cost-extensive measurements. In previous works the application of the Finite Element Method (FEM) was proposed as an effective and cost reducing alternative to predict the surface layer state for given process parameters. However, FEM requires very fine mesh in the surface layer to resolve the high stress gradients with sufficient accuracy. The hereby caused high time and memory requirements render an efficient simulation of complete turbine components as impossible. In this article a solution is offered by coupling the FEM with the Boundary Elements Method (BEM). It enables the computing of large scale models at low computational cost and high result accuracy. Different approaches of the FEM/BEM-coupling for the simulation of deep rolling are examined with regard to their stability and required computing time.

In-situ heater test in sedimentary soft rocks under high temperature (Phase I)

International Nuclear Information System (INIS)

Ikenoya, Takafumi; Takakura, Nozomu; Okada, Tetsuji; Sawada, Masataka; Hirano, Kouhei; Tani, Kazuo

2008-01-01

Various researches have been conducted on high level radioactive waste geological disposal in sedimentary soft rocks. It's noted that the long-term mechanical behaviors of sedimentary soft rocks can be affected by various environmental factors such as temperatures or hydraulic conditions. Therefore, in-situ heater test was conducted in an underground cavern at a depth of 50 meters for the purpose of improving thermo-hydro-mechanical coupled analysis code. This report presents the test result demonstrating the changes of temperature and strain distributions with time at the elevated temperature of the heater up to 40 degrees Celsius. (author)

In-situ heating test in sedimentary soft rock. Phase 2

International Nuclear Information System (INIS)

Ikenoya, Takafumi; Takakura, Nozomu; Okada, Tetsuji; Sawada, Masataka; Hirano, Kouhei; Tani, Kazuo

2011-01-01

Various researches have been conducted on high level radioactive waste geological disposal in sedimentary soft rocks. It is noted that the long-term mechanical behaviors of sedimentary soft rocks can be affected by various environmental factors such as temperatures or hydraulic conditions. Therefore, in-situ heater test was conducted in an underground cavern at a depth of 50 m for the purpose of improving thermo-hydro-mechanical coupled analysis code. This report presents the test result demonstrating the changes of temperature and strain distributions with time at the elevated temperature of the heater up to 90degC. (author)

Modeling and Simulation of the Sulfur-Iodine Process Coupled to a Very High-Temperature Gas-Cooled Nuclear Reactor

Energy Technology Data Exchange (ETDEWEB)

Shin, Youngjoon; Lee, Taehoon; Lee, Kiyoung; Kim, Minhwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

Hydrogen produced from water using nuclear energy will avoid both the use of fossil fuel and CO{sub 2} emission presumed to be the dominant reason for global warming. A thermo-chemical sulfur-iodine (SI) process coupled to a Very High Temperature Gas-Cooled Reactor(VHTR) is one of the most prospective hydrogen production methods that split water using nuclear energy because the SI process is suitable for large-scale hydrogen production without CO{sub 2} emission. The dynamic simulation code to evaluate the start-up behavior of the chemical reactors placed on the secondary helium loop of the SI process has been developed and partially verified using the steady state values obtained from the Aspen Plus{sup TM} Code simulation. As the start-up dynamic simulation results of the SI process coupled to the IHX, which is one of components in the VHTR system, it is expected that the integrated secondary helium loop of the SI process can be successfully and safely approach the steady state condition.

Using Multiscale Modeling to Study Coupled Flow, Transport, Reaction and Biofilm Growth Processes in Porous Media

Science.gov (United States)

Valocchi, A. J.; Laleian, A.; Werth, C. J.

2017-12-01

Perturbation of natural subsurface systems by fluid inputs may induce geochemical or microbiological reactions that change porosity and permeability, leading to complex coupled feedbacks between reaction and transport processes. Some examples are precipitation/dissolution processes associated with carbon capture and storage and biofilm growth associated with contaminant transport and remediation. We study biofilm growth due to mixing controlled reaction of multiple substrates. As biofilms grow, pore clogging occurs which alters pore-scale flow paths thus changing the mixing and reaction. These interactions are challenging to quantify using conventional continuum-scale porosity-permeability relations. Pore-scale models can accurately resolve coupled reaction, biofilm growth and transport processes, but modeling at this scale is not feasible for practical applications. There are two approaches to address this challenge. Results from pore-scale models in generic pore structures can be used to develop empirical relations between porosity and continuum-scale parameters, such as permeability and dispersion coefficients. The other approach is to develop a multiscale model of biofilm growth in which non-overlapping regions at pore and continuum spatial scales are coupled by a suitable method that ensures continuity of flux across the interface. Thus, regions of high reactivity where flow alteration occurs are resolved at the pore scale for accuracy while regions of low reactivity are resolved at the continuum scale for efficiency. This approach thus avoids the need for empirical upscaling relations in regions with strong feedbacks between reaction and porosity change. We explore and compare these approaches for several two-dimensional cases.

Safety Philosophy in Process Heat Plants Coupled to High Temperature Reactors

International Nuclear Information System (INIS)

Brown, Nicholas R.; Revankar, Shripad T.

2011-01-01

With the future availability of fossil fuel resources in doubt, high temperature nuclear reactors have the potential to be an important technology in the near term. Due to a high coolant outlet temperature, high temperature reactors (HTR) can be used to drive chemical plants that directly utilize process heat. Additionally, the high temperature improves the thermodynamic efficiency of the energy utilization. Many applications of high temperature reactors exist as a thermal driving vector for endothermic chemical process plants. Hydrogen generation using the General Atomics (GA) sulfur iodine (SI) cycle is one promising application of high temperature nuclear heat. The main chemical reactions in the SI cycle are: 1. I 2 +SO 2 + 2H 2 O → 2HI + H 2 SO 4 (Bunsen reaction) 2. H 2 SO 4 → H 2 O + SO 2 + 1/2O 2 (Sulfuric acid decomposition) 3. 2HI → H 2 + I 2 (Hydrogen Iodide decomposition). With the exception of hydrogen and oxygen, all relevant reactants are recycled within the process. However, there are many unresolved safety and operational issues related to implementation of such a coupled plant

Match properties of heat transfer and coupled heat and mass transfer processes in air-conditioning system

International Nuclear Information System (INIS)

Zhang Tao; Liu Xiaohua; Zhang Lun; Jiang Yi

2012-01-01

Highlights: ► Investigates match properties of heat or mass transfer processes in HVAC system. ► Losses are caused by limited transfer ability, flow and parameter mismatching. ► Condition of flow matching is the same heat capacity of the fluids. ► Parameter matching is only reached along the saturation line in air–water system. ► Analytical solutions of heat and mass transfer resistance are derived. - Abstract: Sensible heat exchangers and coupled heat and mass transfer devices between humid air and water/desiccant are commonly used devices in air-conditioning systems. This paper focuses on the match properties of sensible heat transfer processes and coupled heat and mass transfer processes in an effort to understand the reasons for performance limitations in order to optimize system performance. Limited heat transfer capability and flow mismatching resulted in heat resistance of the sensible heat transfer process. Losses occurred during the heat and mass transfer processes due to limited transfer capability, flow mismatching, and parameter mismatching. Flow matching was achieved when the heat capacities of the fluids were identical, and parameter matching could only be reached along the saturation line in air–water systems or the iso-concentration line in air–desiccant systems. Analytical solutions of heat transfer resistance and mass transfer resistance were then derived. The heat and mass transfer process close to the saturation line is recommended, and heating sprayed water resulted in better humidification performance than heating inlet air in the air humidifier.

Gay and lesbian couples in Italy: comparisons with heterosexual couples.

Science.gov (United States)

Antonelli, Paolo; Dèttore, Davide; Lasagni, Irene; Snyder, Douglas K; Balderrama-Durbin, Christina

2014-12-01

Assessing couple relationships across diverse languages and cultures has important implications for both clinical intervention and prevention. This is especially true for nontraditional relationships potentially subject to various expressions of negative societal evaluation or bias. Few empirically validated measures of relationship functioning have been developed for cross-cultural applications, and none have been examined for their psychometric sufficiency for evaluating same-sex couples across different languages and cultures. The current study examined the psychometric properties of an Italian translation of the Marital Satisfaction Inventory - Revised (MSI-R), a 150-item 13-scale measure of couple relationship functioning, for its use in assessing the intimate relationships of gay and lesbian couples in Italy. Results for these couples were compared to data from heterosexual married and unmarried cohabiting couples from the same geographical region, as well as to previously published data for gay, lesbian, and unmarried heterosexual couples from the United States. Findings suggest that, despite unique societal pressures confronting Italian same-sex couples, these relationships appear resilient and fare well both overall and in specific domains of functioning compared to heterosexual couples both in Italy and the United States. © 2014 Family Process Institute.

DRIFT-SCALE COUPLED PROCESSES (DST AND TH SEEPAGE) MODELS

International Nuclear Information System (INIS)

J.T. Birkholzer; S. Mukhopadhyay

2005-01-01

The purpose of this report is to document drift-scale modeling work performed to evaluate the thermal-hydrological (TH) behavior in Yucca Mountain fractured rock close to waste emplacement drifts. The heat generated by the decay of radioactive waste results in rock temperatures elevated from ambient for thousands of years after emplacement. Depending on the thermal load, these temperatures are high enough to cause boiling conditions in the rock, giving rise to water redistribution and altered flow paths. The predictive simulations described in this report are intended to investigate fluid flow in the vicinity of an emplacement drift for a range of thermal loads. Understanding the TH coupled processes is important for the performance of the repository because the thermally driven water saturation changes affect the potential seepage of water into waste emplacement drifts. Seepage of water is important because if enough water gets into the emplacement drifts and comes into contact with any exposed radionuclides, it may then be possible for the radionuclides to be transported out of the drifts and to the groundwater below the drifts. For above-boiling rock temperatures, vaporization of percolating water in the fractured rock overlying the repository can provide an important barrier capability that greatly reduces (and possibly eliminates) the potential of water seeping into the emplacement drifts. In addition to this thermal process, water is inhibited from entering the drift opening by capillary forces, which occur under both ambient and thermal conditions (capillary barrier). The combined barrier capability of vaporization processes and capillary forces in the near-field rock during the thermal period of the repository is analyzed and discussed in this report

Using the Model Coupling Toolkit to couple earth system models

Science.gov (United States)

Warner, J.C.; Perlin, N.; Skyllingstad, E.D.

2008-01-01

Continued advances in computational resources are providing the opportunity to operate more sophisticated numerical models. Additionally, there is an increasing demand for multidisciplinary studies that include interactions between different physical processes. Therefore there is a strong desire to develop coupled modeling systems that utilize existing models and allow efficient data exchange and model control. The basic system would entail model "1" running on "M" processors and model "2" running on "N" processors, with efficient exchange of model fields at predetermined synchronization intervals. Here we demonstrate two coupled systems: the coupling of the ocean circulation model Regional Ocean Modeling System (ROMS) to the surface wave model Simulating WAves Nearshore (SWAN), and the coupling of ROMS to the atmospheric model Coupled Ocean Atmosphere Prediction System (COAMPS). Both coupled systems use the Model Coupling Toolkit (MCT) as a mechanism for operation control and inter-model distributed memory transfer of model variables. In this paper we describe requirements and other options for model coupling, explain the MCT library, ROMS, SWAN and COAMPS models, methods for grid decomposition and sparse matrix interpolation, and provide an example from each coupled system. Methods presented in this paper are clearly applicable for coupling of other types of models. ?? 2008 Elsevier Ltd. All rights reserved.

Dark forces coupled to nonconserved currents

Science.gov (United States)

Dror, Jeff A.; Lasenby, Robert; Pospelov, Maxim

2017-10-01

New light vectors with dimension-4 couplings to Standard Model states have (energy/vectormass)2-enhanced production rates unless the current they couple to is conserved. These processes allow us to derive new constraints on the couplings of such vectors, that are significantly stronger than the previous literature for a wide variety of models. Examples include vectors with axial couplings to quarks and vectors coupled to currents (such as baryon number) that are only broken by the chiral anomaly. Our new limits arise from a range of processes, including rare Z decays and flavor-changing meson decays, and rule out a number of phenomenologically motivated proposals.

Coupling regularizes individual units in noisy populations

International Nuclear Information System (INIS)

Ly Cheng; Ermentrout, G. Bard

2010-01-01

The regularity of a noisy system can modulate in various ways. It is well known that coupling in a population can lower the variability of the entire network; the collective activity is more regular. Here, we show that diffusive (reciprocal) coupling of two simple Ornstein-Uhlenbeck (O-U) processes can regularize the individual, even when it is coupled to a noisier process. In cellular networks, the regularity of individual cells is important when a select few play a significant role. The regularizing effect of coupling surprisingly applies also to general nonlinear noisy oscillators. However, unlike with the O-U process, coupling-induced regularity is robust to different kinds of coupling. With two coupled noisy oscillators, we derive an asymptotic formula assuming weak noise and coupling for the variance of the period (i.e., spike times) that accurately captures this effect. Moreover, we find that reciprocal coupling can regularize the individual period of higher dimensional oscillators such as the Morris-Lecar and Brusselator models, even when coupled to noisier oscillators. Coupling can have a counterintuitive and beneficial effect on noisy systems. These results have implications for the role of connectivity with noisy oscillators and the modulation of variability of individual oscillators.

APROS couplings from core to containment

International Nuclear Information System (INIS)

Puska, E.K.; Ylijoki, J.

2005-01-01

APROS simulation environment is able to describe the 1-D and 3-D neutronics of the reactor core. It is also able to describe the thermal hydraulics of the core and circuits either with 5- equation or 6-equation thermal hydraulics. It can also describe the plant automation and electrical systems, as well as the behaviour of the containment. The peculiar feature of APROS in comparison to other coupled systems is that all parts in the coupled system are described with the same code instead of coupling two or three separate codes together with information exchange between the separate codes. The most recent possibility is the coupled calculation of the process and the containment. The more traditional coupling, the coupling of the process containing both the process description and the automation description with more or less detailed description of the 3-D core either for safety analysis or real-time simulation purposes has been discussed in previous work. The paper presents and discusses the capabilities of the code in coupling the plant process and automation description with the plant containment description with two example transient cases. An improved boron concentration solution with second order upwind discretization has been recently included in APROS. An example on the increased accuracy acquired in the 3-D core model has been included. (authors)

Coupled analysis on landscape pattern and hydrological processes in Yanhe watershed of China.

Science.gov (United States)

Li, J; Zhou, Z X

2015-02-01

As a typical experimental Soil and Water Conservation District, Yanhe watershed has long been plagued by soil erosion due to severe human disturbances. Exerting remote sensing (RS) and geographic information system (GIS) technology, this paper firstly analyzed and simulated ecological hydrological process in Yanhe watershed based on SWAT model, constructed a comprehensive landscape indices which was closely related to soil erosion, and reflected the coupling relationship between regional landscape pattern change and soil erosion. The results are as follows: (1) Areas of different land use types remained relatively stable from 1990 to 2000 and then changed drastically from 2000 to 2010, which was characterized by lawn expansion and cultivated land shrinkage. (2) In terms of the spatial heterogeneity of hydrological response unit (HRUs), the correlation coefficient of seven selected landscape indices and runoff was very small, and cannot pass all significant testing. But correlation between the indices and sediment yield except for Total Core Area (TCA) and Interspersion and Juxtaposition Index (IJI) was remarkable. (3) According to 'the source-sink' theory of soil erosion, new landscape index-slope-HRU landscape index (SHLI) was built, and reflected the relationship between landscape pattern and soil erosion processes to a certain extent. (4) Coupling relationship between SHLI in 2010 and annual sediment was very prominent. In the sub-basin scale, SHLI has obvious regional differentiation from annual sediment. Copyright © 2014 Elsevier B.V. All rights reserved.

Anomalous couplings at LEP2

International Nuclear Information System (INIS)

Fayolle, D.

2002-01-01

In its second phase, LEP has allowed to study four fermion processes never observed before. Results are presented on the charged triple gauge boson couplings (TGC) from the W-pair, Single W and Single γ production. The anomalous quartic gauge couplings (QGC) are constrained using production of WWγ, νν-barγγ and Z γγ final states. Finally, limits on the neutral anomalous gauge couplings (NGC) using the Z γ and ZZ production processes are also reported. All results are consistent with the Standard Model expectations. (authors)

Stochastic process of pragmatic information for 2D spiral wave turbulence in globally and locally coupled Alief-Panfilov oscillators

Science.gov (United States)

Kuwahara, Jun; Miyata, Hajime; Konno, Hidetoshi

2017-09-01

Recently, complex dynamics of globally coupled oscillators have been attracting many researcher's attentions. In spite of their numerous studies, their features of nonlinear oscillator systems with global and local couplings in two-dimension (2D) are not understood fully. The paper focuses on 2D states of coherent, clustered and chaotic oscillation especially under the effect of negative global coupling (NGC) in 2D Alief-Panfilov model. It is found that the tuning NGC can cause various new coupling-parameter dependency on the features of oscillations. Then quantitative characterization of various states of oscillations (so called spiral wave turbulence) is examined by using the pragmatic information (PI) which have been utilized in analyzing multimode laser, solar activity and neuronal systems. It is demonstrated that the dynamics of the PI for various oscillations can be characterized successfully by the Hyper-Gamma stochastic process.

Improved representations of coupled soil-canopy processes in the CABLE land surface model (Subversion revision 3432)

Science.gov (United States)

Haverd, Vanessa; Cuntz, Matthias; Nieradzik, Lars P.; Harman, Ian N.

2016-09-01

CABLE is a global land surface model, which has been used extensively in offline and coupled simulations. While CABLE performs well in comparison with other land surface models, results are impacted by decoupling of transpiration and photosynthesis fluxes under drying soil conditions, often leading to implausibly high water use efficiencies. Here, we present a solution to this problem, ensuring that modelled transpiration is always consistent with modelled photosynthesis, while introducing a parsimonious single-parameter drought response function which is coupled to root water uptake. We further improve CABLE's simulation of coupled soil-canopy processes by introducing an alternative hydrology model with a physically accurate representation of coupled energy and water fluxes at the soil-air interface, including a more realistic formulation of transfer under atmospherically stable conditions within the canopy and in the presence of leaf litter. The effects of these model developments are assessed using data from 18 stations from the global eddy covariance FLUXNET database, selected to span a large climatic range. Marked improvements are demonstrated, with root mean squared errors for monthly latent heat fluxes and water use efficiencies being reduced by 40 %. Results highlight the important roles of deep soil moisture in mediating drought response and litter in dampening soil evaporation.

Processes of hydrogen production, coupled with nuclear reactors: Economic perspectives

International Nuclear Information System (INIS)

Werkoff, Francois; Avril, Sophie; Mansilla, Christine; Sigurvinsson, Jon

2006-01-01

Hydrogen production, using nuclear power is considered from a technic-economic (TE) point of view. Three different processes are examined: Alkaline electrolysis, High-temperature steam electrolysis (HTE) and the thermochemical Sulphur-Iodine (S/I) cycle. The three processes differ, in the sense that the first one is operational and both last ones are still at demonstration stages. For them, it is at present only possible to identify key points and limits of competitiveness. The cost of producing hydrogen by alkaline electrolysis is analysed. Three major contributions to the production costs are examined: the electricity consumption, the operation and maintenance expenditures and the depreciation capital expenditures. A technic-economic evaluation of hydrogen production by HTE coupled to a high-temperature reactor (HTR) is presented. Key points appear to be the electrolyser and the high temperature heat exchangers. The S/I thermochemical cycle is based on the decomposition and the re-composition of H 2 SO 4 and HI acids. The energy consumption and the recovery of iodine are key points of the S/I cycle. With the hypothesis that the hydrogen energy will progressively replace the fossil fuels, we give a first estimate of the numbers of nuclear reactors (EPR or HTR) that would be needed for a massive nuclear hydrogen production. (authors)

Optoelectronic properties of Black-Silicon generated through inductively coupled plasma (ICP) processing for crystalline silicon solar cells

Energy Technology Data Exchange (ETDEWEB)

Hirsch, Jens, E-mail: J.Hirsch@emw.hs-anhalt.de [Anhalt University of Applied Sciences, Faculty EMW, Bernburger Str. 55, DE-06366 Köthen (Germany); Fraunhofer Center for Silicon Photovoltaics CSP, Otto-Eißfeldt-Str. 12, DE-06120 Halle (Saale) (Germany); Gaudig, Maria; Bernhard, Norbert [Anhalt University of Applied Sciences, Faculty EMW, Bernburger Str. 55, DE-06366 Köthen (Germany); Lausch, Dominik [Fraunhofer Center for Silicon Photovoltaics CSP, Otto-Eißfeldt-Str. 12, DE-06120 Halle (Saale) (Germany)

2016-06-30

Highlights: • Fabrication of black silicon through inductively coupled plasma (ICP) processing. • Suppressed formation a self-bias and therefore a reduced ion bombardment of the silicon sample. • Reduction of the average hemispherical reflection between 300 and 1120 nm up to 8% within 5 min ICP process time. • Reflection is almost independent of the angle of incidence up to 60°. • 2.5 ms effective lifetime at 10{sup 15} cm{sup −3} MCD after ALD Al{sub 2}O{sub 3} surface passivation. - Abstract: The optoelectronic properties of maskless inductively coupled plasma (ICP) generated black silicon through SF{sub 6} and O{sub 2} are analyzed by using reflection measurements, scanning electron microscopy (SEM) and quasi steady state photoconductivity (QSSPC). The results are discussed and compared to capacitively coupled plasma (CCP) and industrial standard wet chemical textures. The ICP process forms parabolic like surface structures in a scale of 500 nm. This surface structure reduces the average hemispherical reflection between 300 and 1120 nm up to 8%. Additionally, the ICP texture shows a weak increase of the hemispherical reflection under tilted angles of incidence up to 60°. Furthermore, we report that the ICP process is independent of the crystal orientation and the surface roughness. This allows the texturing of monocrystalline, multicrystalline and kerf-less wafers using the same parameter set. The ICP generation of black silicon does not apply a self-bias on the silicon sample. Therefore, the silicon sample is exposed to a reduced ion bombardment, which reduces the plasma induced surface damage. This leads to an enhancement of the effective charge carrier lifetime up to 2.5 ms at 10{sup 15} cm{sup −3} minority carrier density (MCD) after an atomic layer deposition (ALD) with Al{sub 2}O{sub 3}. Since excellent etch results were obtained already after 4 min process time, we conclude that the ICP generation of black silicon is a promising technique

Therapeutically induced changes in couple identity: the role of we-ness and interpersonal processing in relationship satisfaction.

Science.gov (United States)

Reid, David W; Dalton, E Jane; Laderoute, Kristine; Doell, Faye K; Nguyen, Thao

2006-08-01

Changes in partners' sense of self-in-relationship, which a systemic-constructivist couple therapy (SCCT) induced, led to robust improvement in satisfaction in 2 studies and a follow-up study. In each study, 13 referred couples completed measures of satisfaction, mutuality, similarities, and other-in-self construal pre-post 12 hours of SCCT. The authors reliably coded transcripts of 1st and final sessions for each partner's we-ness, the identity that each partner establishes in relationship to the other. Having met the criteria for the rigorous study of change in single group process-outcome design, changes in we-ness accompanied large posttherapy dyadic increments on all variables in each study. Therapeutic gains appeared at follow-up and correlated with increased we-ness obtained at end of therapy 2 years earlier. The authors raise theoretical implications for all types of couple therapies and explain clinical techniques.

Belpex and trilateral market coupling

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-01-15

This document describes the operation of Belpex, the Belgian power transmission spot market, and its linking with the French (Powernext) and Dutch (APX) auction-style day-ahead spot markets. A last part deals with the extension of this trilateral market to other European countries. Content: Belpex day-ahead market (DAM) (Goals of the DAM: Provide consumers with a wider choice of electrical energy sources, Enable the ARP's to optimize their portfolio in terms of imbalance costs, Reduce trade and credit risks for market players compared with the risks involved in concluding bilateral contracts, Provide economic players with a transparent price benchmark, Stimulate the opening of the electricity market); Market model Product (description, Contracts, Collateral calculation, From 12 January to launch date Corporate and Legal Aspects, Next developments); Trilateral Market Coupling (What is market coupling and what are the benefits?, Implementation of trilateral market coupling ('TLC') in France/Belgium/Netherlands, From Trilateral to Multilateral, Implementation of Trilateral Market Coupling (TLC) in France/Belgium/Netherlands, Decentralized market coupling mechanism, influence of import and export on area prices); Decentralized market coupling (2 countries Situations: unconstrained/constrained, Decentralized market coupling: 3 countries, High Level Properties of Market Coupling, Maximize flow until prices across link converge (or ATC limit reached), Power flows from low price area to high price area, Implementing a decentralized technical approach, Market Coupling Daily Process, Impact on Existing Exchange Arrangements, Implementing a decentralized contractual approach, TLC Project Process); From Trilateral to Multilateral (Geographic extensions, Towards an Open and Multilateral Market Coupling, Management of Interconnection Capacities, Interconnection Capacities: current situation, TSO Roles and Responsibilities in the TLC, Other Import/Export products

Belpex and trilateral market coupling

International Nuclear Information System (INIS)

2006-01-01

This document describes the operation of Belpex, the Belgian power transmission spot market, and its linking with the French (Powernext) and Dutch (APX) auction-style day-ahead spot markets. A last part deals with the extension of this trilateral market to other European countries. Content: Belpex day-ahead market (DAM) (Goals of the DAM: Provide consumers with a wider choice of electrical energy sources, Enable the ARP's to optimize their portfolio in terms of imbalance costs, Reduce trade and credit risks for market players compared with the risks involved in concluding bilateral contracts, Provide economic players with a transparent price benchmark, Stimulate the opening of the electricity market); Market model Product (description, Contracts, Collateral calculation, From 12 January to launch date Corporate and Legal Aspects, Next developments); Trilateral Market Coupling (What is market coupling and what are the benefits?, Implementation of trilateral market coupling ('TLC') in France/Belgium/Netherlands, From Trilateral to Multilateral, Implementation of Trilateral Market Coupling (TLC) in France/Belgium/Netherlands, Decentralized market coupling mechanism, influence of import and export on area prices); Decentralized market coupling (2 countries Situations: unconstrained/constrained, Decentralized market coupling: 3 countries, High Level Properties of Market Coupling, Maximize flow until prices across link converge (or ATC limit reached), Power flows from low price area to high price area, Implementing a decentralized technical approach, Market Coupling Daily Process, Impact on Existing Exchange Arrangements, Implementing a decentralized contractual approach, TLC Project Process); From Trilateral to Multilateral (Geographic extensions, Towards an Open and Multilateral Market Coupling, Management of Interconnection Capacities, Interconnection Capacities: current situation, TSO Roles and Responsibilities in the TLC, Other Import/Export products on the

Gas migration in argillaceous rock

International Nuclear Information System (INIS)

Alonso, E. E.; Olivella, S.

2007-01-01

The intrinsic gas permeability of fractured argillaceous rocks depends on the current structure of micro-cracks and fissures of the rock. They are a consequence of the initial state and the subsequent deformations induced by stress and gas pressure changes. Stresses are also coupled with fluid pressures and, therefore, gas flow and mechanical behaviour are intensely coupled. Laboratory experiments, aimed at determining intrinsic permeability, show the relevant effect of volumetric deformations induced by isotropic, as well as deviatoric stress changes. The relevance, in practice, of the flow-mechanical coupling is illustrated by means of some results obtained during the performance of the drift scale test (DST) in fractured tuff in the Yucca Mountain facility. The technique of embedding discontinuities in continuum thermo-hydro-mechanical elements is capable of reproducing observed features of gas flow migration in clayey rocks. An example is described. It is believed that the developed approach provides a powerful computational procedure to handle complex gas phenomena in clayey rocks. (author)

Modeling erosion and sedimentation coupled with hydrological and overland flow processes at the watershed scale

Science.gov (United States)

Kim, Jongho; Ivanov, Valeriy Y.; Katopodes, Nikolaos D.

2013-09-01

A novel two-dimensional, physically based model of soil erosion and sediment transport coupled to models of hydrological and overland flow processes has been developed. The Hairsine-Rose formulation of erosion and deposition processes is used to account for size-selective sediment transport and differentiate bed material into original and deposited soil layers. The formulation is integrated within the framework of the hydrologic and hydrodynamic model tRIBS-OFM, Triangulated irregular network-based, Real-time Integrated Basin Simulator-Overland Flow Model. The integrated model explicitly couples the hydrodynamic formulation with the advection-dominated transport equations for sediment of multiple particle sizes. To solve the system of equations including both the Saint-Venant and the Hairsine-Rose equations, the finite volume method is employed based on Roe's approximate Riemann solver on an unstructured grid. The formulation yields space-time dynamics of flow, erosion, and sediment transport at fine scale. The integrated model has been successfully verified with analytical solutions and empirical data for two benchmark cases. Sensitivity tests to grid resolution and the number of used particle sizes have been carried out. The model has been validated at the catchment scale for the Lucky Hills watershed located in southeastern Arizona, USA, using 10 events for which catchment-scale streamflow and sediment yield data were available. Since the model is based on physical laws and explicitly uses multiple types of watershed information, satisfactory results were obtained. The spatial output has been analyzed and the driving role of topography in erosion processes has been discussed. It is expected that the integrated formulation of the model has the promise to reduce uncertainties associated with typical parameterizations of flow and erosion processes. A potential for more credible modeling of earth-surface processes is thus anticipated.

Treating infidelity in same-sex couples.

Science.gov (United States)

Martell, Christopher R; Prince, Stacey E

2005-11-01

Psychotherapy with same-sex couples does not differ markedly from standard couple therapies; this is also true for treating couples facing infidelity. However, same-sex couples often design their relationships differently, without tradition and formal marital contracts to prescribe behavior. Based on clinical experience and the empirical research, this article addresses the differing norms involved in affirmatively treating infidelity in gay and lesbian couples within the framework of integrative behavioral couple therapy (IBCT). Two cases illustrate the process and outcome of IBCT with same-sex couples.

A small floating seawater desalination plant by using a nuclear heating reactor coupled with the MED process

Energy Technology Data Exchange (ETDEWEB)

Xue Dazhi; Zhang Dafang; Dong Duo [Institute of Nuclear Energy Technology, Tsinghua University, Beijing (China)

2000-03-01

Based on the experience of development of nuclear district heating reactor (NHR) a seawater desalination plant using NHR coupled with the multi-effect distillation (MED) process is being designed. With the same technology a floating desalination plant was proposed to supply potable water to remote areas or islands. With a 10 MWth NHR the floating plant could produce 4000 m{sup 3}/d of potable water and 750 kW of electricity. The design of NHR-10 and the safety features are described. The coupling scheme and parameters are given. Some special considerations for using in ship condition are also presented in this paper. (author)

Poroelastic Modeling as a Proof of Concept for Modular Representation of Coupled Geophysical Processes

Science.gov (United States)

Walker, R. L., II; Knepley, M.; Aminzadeh, F.

2017-12-01

We seek to use the tools provided by the Portable, Extensible Toolkit for Scientific Computation (PETSc) to represent a multiphysics problem in a form that decouples the element definition from the fully coupled equation through the use of pointwise functions that imitate the strong form of the governing equation. This allows allows individual physical processes to be expressed as independent kernels that may be then coupled with the existing finite element framework, PyLith, and capitalizes upon the flexibility offered by the solver, data management, and time stepping algorithms offered by PETSc. To demonstrate a characteristic example of coupled geophysical simulation devised in this manner, we present a model of a synthetic poroelastic environment, with and without the consideration of inertial effects, with fluid initially represented as a single phase. Matrix displacement and fluid pressure serve as the desired unknowns, with the option for various model parameters represented as dependent variables of the central unknowns. While independent of PyLith, this model also serves to showcase the adaptability of physics kernels for synthetic forward modeling. In addition, we seek to expand the base case to demonstrate the impact of modeling fluid as single phase compressible versus a single incompressible phase. As a goal, we also seek to include multiphase fluid modeling, as well as capillary effects.

H, HM, and THM-C processes in engineered barriers

Energy Technology Data Exchange (ETDEWEB)

Cui, Y.J.; Tang, A.M.; Loiseau, C.; Delage, P.; Polak, M.; Souli, H.; Fleureau, J.M.; Wu, P.L.; Tien, Y.M.; Romero, E.; LI, Xiang Ling; Tanaka, Y.; Hasegawa, T.; Nakamura, K.; Sahara, F.; Murakami, T.; Kobayashi, I.; Mihara, M.; Ohi, T.; Lu, J.D.; Huang, W.H.; Lee, W.Y.; Sui, I.H.; Villar, M.V.; Sanchez, M.; Gens, A.; Samper, J.; Lu, C.; Montenegro, L.; Birgersson, M.; Karnland, O.; Nilsson, U.; Akesson, M.; Kristensson, O.; Gatabin, C.; Yang, C.R.; Huang, W.H.; Hsiao, T.H.; Dueck, A.; Lonnqvist, M.; Goudarzi, R.; Borgesson, L.; Fernandez, A.M.; Rivas, P.; Melon, A.M.; Villar, M.V.; Ferrow, E.; Bender Koch, Ch.; Suzuki, S.; Sazarashi, M.; Takegahara, T.; Takao, H.; Tanai, K.; Matsumoto, K.; Gatabin, C.; Touze, G.; Imbert, C.; Guillot, W.; Billaud, P

2007-07-01

This session gathers 24 articles (posters) dealing with: determining water permeability of a compacted bentonite sand mixture under confined and free-swell conditions; the model prediction of engineered barrier system effectiveness in the fracture at laboratory scale; the changes in the hydraulic properties of a smectite in presence of chromium; the wall friction and ejection behaviour of bentonite-base buffer material; the thermo-hydro-mechanical behaviour of a large scale mock-up test 'Ophelie' in Belgium: laboratory characterization and numerical modelling; modeling swelling characteristics and permeability of several compacted bentonite affected by saline water; modelling for the long-term Mechanical and Hydraulic behaviour of bentonite-based materials considering chemical transitions; the coupled thermal-hydro analysis on partially saturated bentonite; the behaviour of a bentonite barrier in the laboratory: experimental results up to 8 years and numerical simulation; a coupled hydrogeochemical calculations of the interactions of corrosion products and bentonite; the freezing in saturated bentonite: a thermodynamic approach; the mechanical modeling of MX-80: Development of constitutive laws; the mechanical modeling of MX-80 - Quick tools for BBM parameter analysis; TBT{sub 3} Mock-up test-experimental and model results; the suction characteristics of two compacted bentonite; the retention curves and volume change properties of unsaturated MX-80 bentonite: a laboratory study; humidity induced swelling and water absorption rate of highly compacted bentonite; unconfined compression tests on bentonite samples exposed to high temperature during long time in the field test lot; the thermophysical properties of bentonite; the geochemistry and mineralogy of a bentonite subjected to heating and hydration in an in-situ test after five years operation; the LOT project, long term test of buffer material at Aespoe: a Moessbauer spectroscopic study; the self

Surface roughening of ground fused silica processed by atmospheric inductively coupled plasma

International Nuclear Information System (INIS)

Xin, Qiang; Li, Na; Wang, Jun; Wang, Bo; Li, Guo; Ding, Fei; Jin, Huiliang

2015-01-01

Highlights: • The morphology evolution of ground fused silica, processed by atmospheric plasma, was investigated experimentally. • The roughness development results from opening and coalescing of the plasma-etched cracks. • The shapes of grain-like etched pits are the results of the adjacent cracks coalescing with one another. • The descent of the pits density is due to some smaller etched pits that are swallowed up by larger pits. • Leading role in surface smoothing is laterally etching away the side walls of the intersecting pits. - Abstract: Subsurface damage (SSD) is a defect that is inevitably induced during mechanical processes, such as grinding and polishing. This defect dramatically reduces the mechanical strength and the laser damage thresholds of optical elements. Compared with traditional mechanical machining, atmospheric pressure plasma processing (APPP) is a relatively novel technology that induces almost no SSD during the processing of silica-based optical materials. In this paper, a form of APPP, inductively coupled plasma (ICP), is used to process fused silica substrates with fluorocarbon precursor under atmospheric pressure. The surface morphology evolution of ICP-processed substrates was observed and characterized by confocal laser scanning microscope (CLSM), field emission scanning electron microscope (SEM), and atomic force microscopy (AFM). The results show that the roughness evolves with the etching depth, and the roughness evolution is a single-peaked curve. This curve results from the opening and the coalescing of surface cracks and fractures. The coalescence procedure of these microstructures was simulated with two common etched pits on a polished fused silica surface. Understanding the roughness evolution of plasma-processed surface might be helpful in optimizing the optical fabrication chain that contains APPP

Surface roughening of ground fused silica processed by atmospheric inductively coupled plasma

Energy Technology Data Exchange (ETDEWEB)

Xin, Qiang; Li, Na; Wang, Jun; Wang, Bo, E-mail: bradywang@hit.edu.cn; Li, Guo; Ding, Fei; Jin, Huiliang

2015-06-30

Highlights: • The morphology evolution of ground fused silica, processed by atmospheric plasma, was investigated experimentally. • The roughness development results from opening and coalescing of the plasma-etched cracks. • The shapes of grain-like etched pits are the results of the adjacent cracks coalescing with one another. • The descent of the pits density is due to some smaller etched pits that are swallowed up by larger pits. • Leading role in surface smoothing is laterally etching away the side walls of the intersecting pits. - Abstract: Subsurface damage (SSD) is a defect that is inevitably induced during mechanical processes, such as grinding and polishing. This defect dramatically reduces the mechanical strength and the laser damage thresholds of optical elements. Compared with traditional mechanical machining, atmospheric pressure plasma processing (APPP) is a relatively novel technology that induces almost no SSD during the processing of silica-based optical materials. In this paper, a form of APPP, inductively coupled plasma (ICP), is used to process fused silica substrates with fluorocarbon precursor under atmospheric pressure. The surface morphology evolution of ICP-processed substrates was observed and characterized by confocal laser scanning microscope (CLSM), field emission scanning electron microscope (SEM), and atomic force microscopy (AFM). The results show that the roughness evolves with the etching depth, and the roughness evolution is a single-peaked curve. This curve results from the opening and the coalescing of surface cracks and fractures. The coalescence procedure of these microstructures was simulated with two common etched pits on a polished fused silica surface. Understanding the roughness evolution of plasma-processed surface might be helpful in optimizing the optical fabrication chain that contains APPP.

Semiclassical derivation of a local optical potential for heavy-ion elastic scattering. [Coupling to other processes

Energy Technology Data Exchange (ETDEWEB)

Donangelo, R; Canto, L F [Rio de Janeiro Univ. (Brazil). Inst. de Fisica; Hussein, M S [Sao Paulo Univ. (Brazil). Inst. de Fisica

1979-05-21

A semiclassical method to determine the contribution to the optical potential in the elastic channel due to the coupling to other processes taking place in heavy-ion collisions is developed. An application is made to the case of Coulomb excitation. The lowest-order term of the potential used is shown to be identical to the potential derived by Baltz et al.

Coupled Environmental Processes and Long-term Performance of Landfill Covers in the northern Mojave Desert

Energy Technology Data Exchange (ETDEWEB)

David Shafer; Michael Young; Stephen Zitzer; Eric McDonald; Todd Caldwell

2004-05-12

Evapotransiration (ET) covers have gained widespread acceptance as a closure feature for waste disposal sites, particularly in the arid and semi-arid regions of the southwestern U.S. But as landforms, ET covers are subject to change over time because of processes such as pedogenesis, hydrologic processes, vegetation establishment and change, and biological processes. To better understand the effects of coupled process changes to ET covers, a series of four primary analog sites in Yucca Flat on the Nevada Test Site, along with measurements and observations from other locations in the Mojave Desert, were selected to evaluate changes in ET covers over time. The analog sites, of varying ages, were selected to address changes in the early post-institutional control period, the 1,000-year compliance period for disposal of low-level and mixed low-level waste, and the 10,000-year compliance period for transuranic waste sites.

Coupled Environmental Processes and Long-term Performance of Landfill Covers in the northern Mojave Desert

International Nuclear Information System (INIS)

David Shafer; Michael Young; Stephen Zitzer; Eric McDonald; Todd Caldwell

2004-01-01

Evapotransiration (ET) covers have gained widespread acceptance as a closure feature for waste disposal sites, particularly in the arid and semi-arid regions of the southwestern U.S. But as landforms, ET covers are subject to change over time because of processes such as pedogenesis, hydrologic processes, vegetation establishment and change, and biological processes. To better understand the effects of coupled process changes to ET covers, a series of four primary analog sites in Yucca Flat on the Nevada Test Site, along with measurements and observations from other locations in the Mojave Desert, were selected to evaluate changes in ET covers over time. The analog sites, of varying ages, were selected to address changes in the early post-institutional control period, the 1,000-year compliance period for disposal of low-level and mixed low-level waste, and the 10,000-year compliance period for transuranic waste sites

Gestural coupling and social cognition

DEFF Research Database (Denmark)

Michael, John; Krueger, Joel William

2012-01-01

Social cognition researchers have become increasingly interested in the ways that behavioral, physiological, and neural coupling facilitate social interaction and interpersonal understanding. We distinguish two ways of conceptualizing the role of such coupling processes in social cognition: strong...... an essential enabling feature for social interaction and interpersonal understanding more generally and thus ought to exhibit severe deficits in these areas. We challenge SI's prediction and show how MS cases offer compelling reasons for instead adopting MI's pluralistic model of social interaction...... and interpersonal understanding. We conclude that investigations of coupling processes within social interaction should inform rather than marginalize or eliminate investigation of higher-level individual cognition...

Definition and implementation of a fully coupled THM model for unsaturated soils

International Nuclear Information System (INIS)

Haxaire, A.; Galavi, V.; Brinkgreve, R.B.J.

2012-01-01

Document available in extended abstract form only. The governing equations of a coupled thermo-hydro-mechanical (THM) model are presented. They are an extension to the previous work of Galavi (2011) in which a coupled THM model based on Biot's consolidation theory was developed for saturated and partially saturated soils. This study is based on the assumption of local thermodynamical equilibrium, meaning that all phases have the same temperature at a point of the multiphase porous medium. The model is implemented in a research version of PLAXIS 2D. The non isothermal partially saturated flow is modeled using the water mass balance described in Rutqvist et al. (2001), in which the flux is decomposed in water advection and vapor diffusion. A limiting hypothesis lies in the gas pressure assumed to be constant in the entire domain. The air flow as a separate phase is therefore neglected. This choice results in having only one independent unknown in the fluid mass balance equation, which is water pressure. However, the vapor diffusion can still be modeled. It depends on temperature by means of a decomposition in a water pressure gradient part and a temperature gradient part. The vapor density follows the psychrometric law. The water storage is described using the ratio of saturation in the soil, the mechanical volumetric strains, and the variation of the skeleton density. To model the influence of water flow in the heat transport equation, the flux term is split in an averaged conductive term and a water advection term. The other quantities such as heat capacity and density are also averaged. This yields a simple yet accurate representation of the interactions between water flow and temperature. The non-isothermal deformation is formulated in terms of Bishop stresses. The effective saturation is taken as the Bishop coefficient. This provides a better accuracy compared to experimental results. The anisotropic thermal expansion tensor is used for the drained linear

Multiobjective Optimization of ELID Grinding Process Using Grey Relational Analysis Coupled with Principal Component Analysis

Directory of Open Access Journals (Sweden)

S. Prabhu

2014-06-01

Full Text Available Carbon nanotube (CNT mixed grinding wheel has been used in the electrolytic in-process dressing (ELID grinding process to analyze the surface characteristics of AISI D2 Tool steel material. CNT grinding wheel is having an excellent thermal conductivity and good mechanical property which is used to improve the surface finish of the work piece. The multiobjective optimization of grey relational analysis coupled with principal component analysis has been used to optimize the process parameters of ELID grinding process. Based on the Taguchi design of experiments, an L9 orthogonal array table was chosen for the experiments. The confirmation experiment verifies the proposed that grey-based Taguchi method has the ability to find out the optimal process parameters with multiple quality characteristics of surface roughness and metal removal rate. Analysis of variance (ANOVA has been used to verify and validate the model. Empirical model for the prediction of output parameters has been developed using regression analysis and the results were compared for with and without using CNT grinding wheel in ELID grinding process.

Convergent-close-coupling calculations for excitation and ionization processes of electron-hydrogen collisions in Debye plasmas

International Nuclear Information System (INIS)

Zammit, Mark C.; Fursa, Dmitry V.; Bray, Igor

2010-01-01

Electron-hydrogen scattering in weakly coupled hot-dense plasmas has been investigated using the convergent-close-coupling method. The Yukawa-type Debye-Hueckel potential has been used to describe the plasma screening effects. The target structure, excitation dynamics, and ionization process change dramatically as the screening is increased. Excitation cross sections for the 1s→2s,2p,3s,3p,3d and 2s→2p,3s,3p,3d transitions and total and total ionization cross sections for the scattering from the 1s and 2s states are presented. Calculations cover the energy range from thresholds to high energies (250 eV) for various Debye lengths. We find that as the screening increases, the excitation and total cross sections decrease, while the total ionization cross sections increase.

Technical basis and programmatic requirements for large block testing of coupled thermal-mechanical-hydrological-chemical processes

International Nuclear Information System (INIS)

Lin, Wunan.

1993-09-01

This document contains the technical basis and programmatic requirements for a scientific investigation plan that governs tests on a large block of tuff for understanding the coupled thermal- mechanical-hydrological-chemical processes. This study is part of the field testing described in Section 8.3.4.2.4.4.1 of the Site Characterization Plan (SCP) for the Yucca Mountain Project. The first, and most important objective is to understand the coupled TMHC processes in order to develop models that will predict the performance of a nuclear waste repository. The block and fracture properties (including hydrology and geochemistry) can be well characterized from at least five exposed surfaces, and the block can be dismantled for post-test examinations. The second objective is to provide preliminary data for development of models that will predict the quality and quantity of water in the near-field environment of a repository over the current 10,000 year regulatory period of radioactive decay. The third objective is to develop and evaluate the various measurement systems and techniques that will later be employed in the Engineered Barrier System Field Tests (EBSFT)

Capturing poromechanical coupling effects of the reactive fracturing process in porous rock via a DEM-network model

Science.gov (United States)

Ulven, Ole Ivar; Sun, WaiChing

2016-04-01

Fluid transport in a porous medium has important implications for understanding natural geological processes. At a sufficiently large scale, a fluid-saturated porous medium can be regarded as a two-phase continuum, with the fluid constituent flowing in the Darcian regime. Nevertheless, a fluid mediated chemical reaction can in some cases change the permeability of the rock locally: Mineral dissolution can cause increased permeability, whereas mineral precipitation can reduce the permeability. This might trigger a complicated hydro-chemo-mechanical coupling effect that causes channeling of fluids or clogging of the system. If the fluid is injected or produced at a sufficiently high rate, the pressure might increase enough to cause the onset and propagation of fractures. Fractures in return create preferential flow paths that enhance permeability, localize fluid flow and chemical reaction, prevent build-up of pore pressure and cause anisotropy of the hydro-mechanical responses of the effective medium. This leads to a complex coupled process of solid deformation, chemical reaction and fluid transport enhanced by the fracture formation. In this work, we develop a new coupled numerical model to study the complexities of feedback among fluid pressure evolution, fracture formation and permeability changes due to a chemical process in a 2D system. We combine a discrete element model (DEM) previously used to study a volume expanding process[1, 2] with a new fluid transport model based on poroelasticity[3] and a fluid-mediated chemical reaction that changes the permeability of the medium. This provides new insights into the hydro-chemo-mechanical process of a transforming porous medium. References [1] Ulven, O. I., Storheim, H., Austrheim, H., and Malthe-Sørenssen, A. "Fracture Initiation During Volume Increasing Reactions in Rocks and Applications for CO2 Sequestration", Earth Planet. Sc. Lett. 389C, 2014a, pp. 132 - 142, doi:10.1016/j.epsl.2013.12.039. [2] Ulven, O. I

Therapy of a couple with a bipolar spouse.

Science.gov (United States)

Witusik, Andrzej; Pietras, Tadeusz

2017-10-23

Qualitative analysis of therapy of a couple with a partner who has bipolar disorder is an important research paradigm in contemporary psychotherapy of mental disorders.The qualitative method of the study is important both from the cognitive point of view and for the evaluation of the therapeutic efficacy in the individual, idiographical aspect. The aim of the study is a qualitative analysis of the therapeutic process of a couple in which one partner suffers from bipolar affective disorder. The study of the couple therapy process utilized the qualitative research methodology using variouspsychotherapeutic paradigms indicating the interrelationships that exist between relapses of the disease and functioning of the couple. The importance of triangulation processes, inheritance of transgenerational myths and dysfunctional cognitive patterns in the functional destabilization of a couple with one partner suffering from bipolar affective disorder was indicated. The study of the couple therapy process utilized the qualitative research methodology using variouspsychotherapeutic paradigms indicating the interrelationships that exist between relapses of the disease and functioning of the couple. The importance of triangulation processes, inheritance of transgenerational myths and dysfunctional cognitive patterns in the functional destabilization of a couple with one partner suffering from bipolar affective disorder was indicated. The dysfunctionality of the discussed couple is largely due to the effects of bipolar disorder and related disturbances on marital functioning. The spectrum of autism in the child is probably related both to the genetic strain of predisposition to psychiatric disorders and to the dysfunctionality of the parental dyad. The presence of bipolar affective disorder in the partner's family is also a genetic burden. The wife's aggression represents probably a syndrome of adaptation to disease in the family. Aggression plays a morphostatic role in the couple

Study of the $W^+ W^- \\gamma$ Process and Limits on Anomalous Quartic Gauge Boson Couplings at LEP

CERN Document Server

Achard, P.; Aguilar-Benitez, M.; Alcaraz, J.; Alemanni, G.; Allaby, J.; Aloisio, A.; Alviggi, M.G.; Anderhub, H.; Andreev, Valery P.; Anselmo, F.; Arefev, A.; Azemoon, T.; Aziz, T.; Bagnaia, P.; Bajo, A.; Baksay, G.; Baksay, L.; Baldew, S.V.; Banerjee, S.; Banerjee, Sw.; Barczyk, A.; Barillere, R.; Bartalini, P.; Basile, M.; Batalova, N.; Battiston, R.; Bay, A.; Becattini, F.; Becker, U.; Behner, F.; Bellucci, L.; Berbeco, R.; Berdugo, J.; Berges, P.; Bertucci, B.; Betev, B.L.; Biasini, M.; Biglietti, M.; Biland, A.; Blaising, J.J.; Blyth, S.C.; Bobbink, G.J.; Bohm, A.; Boldizsar, L.; Borgia, B.; Bottai, S.; Bourilkov, D.; Bourquin, M.; Braccini, S.; Branson, J.G.; Brochu, F.; Buijs, A.; Burger, J.D.; Burger, W.J.; Cai, X.D.; Capell, M.; Cara Romeo, G.; Carlino, G.; Cartacci, A.; Casaus, J.; Cavallari, F.; Cavallo, N.; Cecchi, C.; Cerrada, M.; Chamizo, M.; Chang, Y.H.; Chemarin, M.; Chen, A.; Chen, G.; Chen, G.M.; Chen, H.F.; Chen, H.S.; Chiefari, G.; Cifarelli, L.; Cindolo, F.; Clare, I.; Clare, R.; Coignet, G.; Colino, N.; Costantini, S.; de la Cruz, B.; Cucciarelli, S.; van Dalen, J.A.; de Asmundis, R.; Deglon, P.; Debreczeni, J.; Degre, A.; Deiters, K.; della Volpe, D.; Delmeire, E.; Denes, P.; DeNotaristefani, F.; De Salvo, A.; Diemoz, M.; Dierckxsens, M.; van Dierendonck, D.; Dionisi, C.; Dittmar, M.; Doria, A.; Dova, M.T.; Duchesneau, D.; Duinker, P.; Echenard, B.; Eline, A.; El Mamouni, H.; Engler, A.; Eppling, F.J.; Ewers, A.; Extermann, P.; Falagan, M.A.; Falciano, S.; Favara, A.; Fay, J.; Fedin, O.; Felcini, M.; Ferguson, T.; Fesefeldt, H.; Fiandrini, E.; Field, J.H.; Filthaut, F.; Fisher, P.H.; Fisher, W.; Fisk, I.; Forconi, G.; Freudenreich, K.; Furetta, C.; Galaktionov, Iouri; Ganguli, S.N.; Garcia-Abia, Pablo; Gataullin, M.; Gentile, S.; Giagu, S.; Gong, Z.F.; Grenier, Gerald Jean; Grimm, O.; Gruenewald, M.W.; Guida, M.; van Gulik, R.; Gupta, V.K.; Gurtu, A.; Gutay, L.J.; Haas, D.; Hatzifotiadou, D.; Hebbeker, T.; Herve, Alain; Hirschfelder, J.; Hofer, H.; Hohlmann, M.; Holzner, G.; Hou, S.R.; Hu, Y.; Jin, B.N.; Jones, Lawrence W.; de Jong, P.; Josa-Mutuberria, I.; Kafer, D.; Kaur, M.; Kienzle-Focacci, M.N.; Kim, J.K.; Kirkby, Jasper; Kittel, W.; Klimentov, A.; Konig, A.C.; Kopal, M.; Koutsenko, V.; Kraber, M.; Kraemer, R.W.; Krenz, W.; Kruger, A.; Kunin, A.; Ladron de Guevara, P.; Laktineh, I.; Landi, G.; Lebeau, M.; Lebedev, A.; Lebrun, P.; Lecomte, P.; Lecoq, P.; Le Coultre, P.; Le Goff, J.M.; Leiste, R.; Levtchenko, P.; Li, C.; Likhoded, S.; Lin, C.H.; Lin, W.T.; Linde, F.L.; Lista, L.; Liu, Z.A.; Lohmann, W.; Longo, E.; Lu, Y.S.; Lubelsmeyer, K.; Luci, C.; Luminari, L.; Lustermann, W.; Ma, W.G.; Malgeri, L.; Malinin, A.; Mana, C.; Mangeol, D.; Mans, J.; Martin, J.P.; Marzano, F.; Mazumdar, K.; McNeil, R.R.; Mele, S.; Merola, L.; Meschini, M.; Metzger, W.J.; Mihul, A.; Milcent, H.; Mirabelli, G.; Mnich, J.; Mohanty, G.B.; Muanza, G.S.; Muijs, A.J.M.; Musicar, B.; Musy, M.; Nagy, S.; Natale, S.; Napolitano, M.; Nessi-Tedaldi, F.; Newman, H.; Niessen, T.; Nisati, A.; Kluge, Hannelies; Ofierzynski, R.; Organtini, G.; Palomares, C.; Pandoulas, D.; Paolucci, P.; Paramatti, R.; Passaleva, G.; Patricelli, S.; Paul, Thomas Cantzon; Pauluzzi, M.; Paus, C.; Pauss, F.; Pedace, M.; Pensotti, S.; Perret-Gallix, D.; Petersen, B.; Piccolo, D.; Pierella, F.; Pioppi, M.; Piroue, P.A.; Pistolesi, E.; Plyaskin, V.; Pohl, M.; Pojidaev, V.; Pothier, J.; Prokofev, D.O.; Prokofiev, D.; Quartieri, J.; Rahal-Callot, G.; Rahaman, M.A.; Raics, P.; Raja, N.; Ramelli, R.; Rancoita, P.G.; Ranieri, R.; Raspereza, A.; Razis, P.; Ren, D.; Rescigno, M.; Reucroft, S.; Riemann, S.; Riles, Keith; Roe, B.P.; Romero, L.; Rosca, A.; Rosier-Lees, S.; Roth, Stefan; Rosenbleck, C.; Roux, B.; Rubio, J.A.; Ruggiero, G.; Rykaczewski, H.; Sakharov, A.; Saremi, S.; Sarkar, S.; Salicio, J.; Sanchez, E.; Sanders, M.P.; Schafer, C.; Schegelsky, V.; Schmidt-Kaerst, S.; Schmitz, D.; Schopper, H.; Schotanus, D.J.; Schwering, G.; Sciacca, C.; Servoli, L.; Shevchenko, S.; Shivarov, N.; Shoutko, V.; Shumilov, E.; Shvorob, A.; Siedenburg, T.; Son, D.; Spillantini, P.; Steuer, M.; Stickland, D.P.; Stoyanov, B.; Straessner, A.; Sudhakar, K.; Sultanov, G.; Sun, L.Z.; Sushkov, S.; Suter, H.; Swain, J.D.; Szillasi, Z.; Tang, X.W.; Tarjan, P.; Tauscher, L.; Taylor, L.; Tellili, B.; Teyssier, D.; Timmermans, Charles; Ting, Samuel C.C.; Ting, S.M.; Tonwar, S.C.; Toth, J.; Tully, C.; Tung, K.L.; Ulbricht, J.; Valente, E.; Van de Walle, R.T.; Veszpremi, V.; Vesztergombi, G.; Vetlitsky, I.; Vicinanza, D.; Violini, P.; Viertel, G.; Villa, S.; Vivargent, M.; Vlachos, S.; Vodopianov, I.; Vogel, H.; Vogt, H.; Vorobev, I.; Vorobyov, A.A.; Wadhwa, M.; Wallraff, W.; Wang, X.L.; Wang, Z.M.; Weber, M.; Wienemann, P.; Wilkens, H.; Wynhoff, S.; Xia, L.; Xu, Z.Z.; Yamamoto, J.; Yang, B.Z.; Yang, C.G.; Yang, H.J.; Yang, M.; Yeh, S.C.; Zalite, A.; Zalite, Yu.; Zhang, Z.P.; Zhao, J.; Zhu, G.Y.; Zhu, R.Y.; Zhuang, H.L.; Zichichi, A.; Zilizi, G.; Zimmermann, B.; Zoller, M.

2002-01-01

The process e+e- --> W+ W- \\gamma is studied using the data collected by the L3 detector at LEP. New results, corresponding to an integrated luminosity of 427.4 pb-1 at centre-of-mass energies from 192~GeV to 207~GeV, are presented. The W+W-\\gamma cross sections are measured to be in agreement with Standard Model expectations. No hints of anomalous quartic gauge boson couplings are observed. Limits at 95\\% confidence level are derived using also the process e+e- --> \

Effector-Triggered Self-Replication in Coupled Subsystems

NARCIS (Netherlands)

Komáromy, Dávid; Tezcan, Meniz; Schaeffer, Gaël; Marić, Ivana; Otto, Sijbren

2017-01-01

In living systems processes like genome duplication and cell division are carefully synchronized through subsystem coupling. If we are to create life de novo, similar control over essential processes such as self-replication need to be developed. Here we report that coupling two dynamic

Study of thermo-hydro-mechanical processes at a potential site of an ...

Indian Academy of Sciences (India)

2008-09-29

Sep 29, 2008 ... In this paper, field investigation has been done near to Bhima basin of peninsular India. Detailed ... investigations and other state-of-the-art methods .... Table 1. Variation of physico-mechanical parameters with depth. Tensile. Angle of. UCS strength. Cohesive internal. Young's. Sample nos. Depth. (σc). (σt).

Termination of pregnancy following a prenatal diagnosis of Down syndrome: A qualitative study of the decision-making process of pregnant couples.

Science.gov (United States)

Lou, Stina; Carstensen, Kathrine; Petersen, Olav Bjørn; Nielsen, Camilla Palmhøj; Hvidman, Lone; Lanther, Maja Retpen; Vogel, Ida

2018-05-23

In Denmark, first trimester screening has a very high uptake (>90%). If Down syndrome is diagnosed, termination rates are high (>95%). The aim of this study was to investigate the timing of the decision to terminate pregnancy following a diagnosis of Down syndrome and the factors influencing this decision. Semi-structured, qualitative interview study with 21 couples who had received a prenatal diagnosis of Down syndrome and decided to terminate the pregnancy. Participants were recruited from obstetric departments between February 2016 and July 2017. Data were analyzed using thematic analysis. Five themes were identified: "initial decision-making", "consolidating the decision", "reasons and concerns shaping the termination of pregnancy decision", "the right decision is also burdensome", and "perceived influences in decision-making". For most couples, the initial decision to terminate pregnancy was made before or during the diagnostic process, but it was re-addressed and consolidated following the actual diagnosis. Imagining a family future with a severely affected Down syndrome child was the main factor influencing the termination of pregnancy decision. The decision was articulated as "right" but also as existentially burdensome for some, due to fear of regret and concern about ending a potential life. The decision to terminate pregnancy was considered a private matter between the couple, but was refined through interactions with clinicians and social networks. All couples made an initial decision prior to receiving the Down syndrome diagnosis. Knowledge of the couple's initial decision may facilitate patient-centered communication during and after the diagnostic process. Couples may benefit from counseling to deal with grief and existential concerns. © 2018 Nordic Federation of Societies of Obstetrics and Gynecology.

Effect of medium on friction and wear properties of compacted graphite cast iron processed by biomimetic coupling laser remelting process

International Nuclear Information System (INIS)

Guo Qingchun; Zhou Hong; Wang Chengtao; Zhang Wei; Lin Pengyu; Sun Na; Ren Luquan

2009-01-01

Stimulated by the cuticles of soil animals, an attempt to improve the wear resistance of compact graphite cast iron (CGI) with biomimetic units on the surface was made by using a biomimetic coupled laser remelting process in air and various thicknesses water film, respectively. The microstructures of biomimetic units were examined by scanning electron microscope and X-ray diffraction was used to describe the microstructure and identify the phases in the melted zone. Microhardness was measured and the wear behaviors of biomimetic specimens as functions of different mediums as well as various water film thicknesses were investigated under dry sliding condition, respectively. The results indicated that the microstructure zones in the biomimetic specimens processed with water film are refined compared with that processed in air and had better wear resistance increased by 60%, the microhardness of biomimetic units has been improved significantly. The application of water film provided finer microstructures and much more regular grain shape in biomimetic units, which played a key role in improving the friction properties and wear resistance of CGI.

Effect of medium on friction and wear properties of compacted graphite cast iron processed by biomimetic coupling laser remelting process

Science.gov (United States)

Guo, Qing-chun; Zhou, Hong; Wang, Cheng-tao; Zhang, Wei; Lin, Peng-yu; Sun, Na; Ren, Luquan

2009-04-01

Stimulated by the cuticles of soil animals, an attempt to improve the wear resistance of compact graphite cast iron (CGI) with biomimetic units on the surface was made by using a biomimetic coupled laser remelting process in air and various thicknesses water film, respectively. The microstructures of biomimetic units were examined by scanning electron microscope and X-ray diffraction was used to describe the microstructure and identify the phases in the melted zone. Microhardness was measured and the wear behaviors of biomimetic specimens as functions of different mediums as well as various water film thicknesses were investigated under dry sliding condition, respectively. The results indicated that the microstructure zones in the biomimetic specimens processed with water film are refined compared with that processed in air and had better wear resistance increased by 60%, the microhardness of biomimetic units has been improved significantly. The application of water film provided finer microstructures and much more regular grain shape in biomimetic units, which played a key role in improving the friction properties and wear resistance of CGI.

Simulation of Mechanical Processes in Gas Storage Caverns for Short-Term Energy Storage

Science.gov (United States)

Böttcher, Norbert; Nagel, Thomas; Kolditz, Olaf

2015-04-01

In recent years, Germany's energy management has started to be transferred from fossil fuels to renewable and sustainable energy carriers. Renewable energy sources such as solar and wind power are subjected by fluctuations, thus the development and extension of energy storage capacities is a priority in German R&D programs. This work is a part of the ANGUS+ Project, funded by the federal ministry of education and research, which investigates the influence of subsurface energy storage on the underground. The utilization of subsurface salt caverns as a long-term storage reservoir for fossil fuels is a common method, since the construction of caverns in salt rock is inexpensive in comparison to solid rock formations due to solution mining. Another advantage of evaporate as host material is the self-healing behaviour of salt rock, thus the cavity can be assumed to be impermeable. In the framework of short-term energy storage (hours to days), caverns can be used as gas storage reservoirs for natural or artificial fuel gases, such as hydrogen, methane, or compressed air, where the operation pressures inside the caverns will fluctuate more frequently. This work investigates the influence of changing operation pressures at high frequencies on the stability of the host rock of gas storage caverns utilizing numerical models. Therefore, we developed a coupled Thermo-Hydro-Mechanical (THM) model based on the finite element method utilizing the open-source software platform OpenGeoSys. The salt behaviour is described by well-known constitutive material models which are capable of predicting creep, self-healing, and dilatancy processes. Our simulations include the thermodynamic behaviour of gas storage process, temperature development and distribution on the cavern boundary, the deformation of the cavern geometry, and the prediction of the dilatancy zone. Based on the numerical results, optimal operation modes can be found for individual caverns, so the risk of host rock damage

Influences of Coupled Hydrologic and Microbial Processes on River Corridor Biogeochemistry and Ecology

Science.gov (United States)

Scheibe, T. D.; Song, H. S.; Stegen, J.; Graham, E.; Bao, J.; Goldman, A.; Zhou, T.; Crump, A.; Hou, Z.; Hammond, G. E.; Chen, X.; Huang, M.; Zhang, X.; Nelson, W. C.; Garayburu-Caruso, V. A.

2017-12-01

The exchange of water between rivers and surrounding subsurface environments (hydrologic exchange flows or HEFs) is a vital aspect of river ecology and watershed function. HEFs play a key role in water quality, nutrient cycling, and ecosystem health, and they modulate water temperatures and enhance exchange of terrestrial and aquatic nutrients, which lead to elevated biogeochemical activity. However, these coupled hydrologic and microbiological processes are not well understood, particularly in the context of large managed river systems with highly variable discharge, and are poorly represented in system-scale quantitative models. Using the 75 km Hanford Reach of the Columbia River as the research domain, we apply high-resolution flow simulations supported by field observations to understand how variable river discharge interacts with hydromorphic and hydrogeologic structures to generate HEFs and distributions of subsurface residence times. We combine this understanding of hydrologic processes with microbiological activity measurements and reactive transport models to elucidate the holistic impacts of variable discharge on river corridor (surface and subsurface) ecosystems. In particular, our project seeks to develop and test new conceptual and numerical models that explicitly incorporate i) the character (chemical speciation and thermodynamics) of natural organic matter as it varies along flow paths and through mixing of groundwater and surface water, and ii) the history-dependent response of microbial communities to varying time scales of inundation associated with fluctuations in river discharge. The results of these high-resolution mechanistic models are guiding formulation and parameterization of reduced-order models applicable at reach to watershed scales. New understanding of coupled hydrology and microbiology in the river corridor will play a key role in reduction of uncertainties associated with major Earth system biogeochemical fluxes, improving

Poleward propagation of boreal summer intraseasonal oscillations in a coupled model: role of internal processes

Energy Technology Data Exchange (ETDEWEB)

Ajayamohan, R.S. [University of Victoria, Canadian Centre for Climate Modelling and Analysis, P.O. Box 3065, Victoria, BC (Canada); Annamalai, H.; Hafner, Jan [University of Hawaii, International Pacific Research Center, Honolulu (United States); Luo, Jing-Jia [Japan Agency for Marine-Earth Science and Technology, Frontier Research Centre for Global Change, Yokohama (Japan); Yamagata, Toshio [Japan Agency for Marine-Earth Science and Technology, Frontier Research Centre for Global Change, Yokohama (Japan); The University of Tokyo, Department of Earth and Planetary Science, Tokyo (Japan)

2011-09-15

The study compares the simulated poleward migration characteristics of boreal summer intraseasonal oscillations (BSISO) in a suite of coupled ocean-atmospheric model sensitivity integrations. The sensitivity experiments are designed in such a manner to allow full coupling in specific ocean basins but forced by temporally varying monthly climatological sea surface temperature (SST) adopted from the fully coupled model control runs (ES10). While the local air-sea interaction is suppressed in the tropical Indian Ocean and allowed in the other oceans in the ESdI run, it is suppressed in the tropical Pacific and allowed in the other oceans in the ESdP run. Our diagnostics show that the basic mean state in precipitation and easterly vertical shear as well as the BSISO properties remain unchanged due to either inclusion or exclusion of local air-sea interaction. In the presence of realistic easterly vertical shear, the continuous emanation of Rossby waves from the equatorial convection is trapped over the monsoon region that enables the poleward propagation of BSISO anomalies in all the model sensitivity experiments. To explore the internal processes that maintain the tropospheric moisture anomalies ahead of BSISO precipitation anomalies, moisture and moist static energy budgets are performed. In all model experiments, advection of anomalous moisture by climatological winds anchors the moisture anomalies that in turn promote the northward migration of BSISO precipitation. While the results indicate the need for realistic simulation of all aspects of the basic state, our model results need to be taken with caution because in the ECHAM family of coupled models the internal variance at intraseasonal timescales is indeed very high, and therefore local air-sea interactions may not play a pivotal role. (orig.)

Heat Recovery from Multiple-Fracture Enhanced Geothermal Systems: The Effect of Thermoelastic Fracture Interactions

DEFF Research Database (Denmark)

Vik, Hedda Slatlem; Salimzadeh, Saeed; Nick, Hamid

2018-01-01

This study investigates the effect of thermoelastic interactions between multiple parallel fractures on energy production from a multiple-fracture enhanced geothermal system. A coupled thermo-hydro-mechanical finite element model has been developed that accounts for non-isothermal fluid flow within...... increased to maximise the net energy production from the system. Otherwise, the multiple-fracture system fails to improve the energy recovery from the geothermal reservoir, as initially intended....... aperture in the adjacent fracture, and facilitates the creation of favourable flow pathways between the injection and production wells. These flow paths reduce the energy production from the system. The effects of fracture spacing, reservoir temperature gradient and mechanical properties of the rock matrix...

ESPC Coupled Global Prediction System

Science.gov (United States)

2015-09-30

through an improvement to the sea ice albedo . Fig. 3: 2-m Temperature bias (deg C) of 120-h forecasts for the month of May 2014 for the Arctic...forecast system (NAVGEM) and ocean- sea ice forecast system (HYCOM/CICE) have never been coupled at high resolution. The coupled processes will be...winds and currents across the interface. The sea - ice component of this project requires modification of CICE versions 4 and 5 to run in the coupled

A Review of the Research in Emotionally Focused Therapy for Couples.

Science.gov (United States)

Wiebe, Stephanie A; Johnson, Susan M

2016-09-01

Emotionally Focused Therapy for Couples (EFT) is a brief evidence-based couple therapy based in attachment theory. Since the development of EFT, efficacy and effectiveness research has accumulated to address a range of couple concerns. EFT meets or exceeds the guidelines for classification as an evidence-based couple therapy outlined for couple and family research. Furthermore, EFT researchers have examined the process of change and predictors of outcome in EFT. Future research in EFT will continue to examine the process of change in EFT and test the efficacy and effectiveness of EFT in new applications and for couples of diverse backgrounds and concerns. © 2016 Family Process Institute.

Study of the $e^+ e^- \\to Z \\gamma$ Process at LEP and Limits on Triple Neutral-Gauge-Boson Couplings

CERN Document Server

Achard, P.; Aguilar-Benitez, M.; Alcaraz, J.; Alemanni, G.; Allaby, J.; Aloisio, A.; Alviggi, M.G.; Anderhub, H.; Andreev, Valery P.; Anselmo, F.; Arefev, A.; Azemoon, T.; Aziz, T.; Bagnaia, P.; Bajo, A.; Baksay, G.; Baksay, L.; Baldew, S.V.; Banerjee, S.; Banerjee, Sw.; Barczyk, A.; Barillere, R.; Bartalini, P.; Basile, M.; Batalova, N.; Battiston, R.; Bay, A.; Becattini, F.; Becker, U.; Behner, F.; Bellucci, L.; Berbeco, R.; Berdugo, J.; Berges, P.; Bertucci, B.; Betev, B.L.; Biasini, M.; Biglietti, M.; Biland, A.; Blaising, J.J.; Blyth, S.C.; Bobbink, G.J.; Bohm, A.; Boldizsar, L.; Borgia, B.; Bottai, S.; Bourilkov, D.; Bourquin, M.; Braccini, S.; Branson, J.G.; Brochu, F.; Burger, J.D.; Burger, W.J.; Cai, X.D.; Capell, M.; Cara Romeo, G.; Carlino, G.; Cartacci, A.; Casaus, J.; Cavallari, F.; Cavallo, N.; Cecchi, C.; Cerrada, M.; Chamizo, M.; Chang, Y.H.; Chemarin, M.; Chen, A.; Chen, G.; Chen, G.M.; Chen, H.F.; Chen, H.S.; Chiefari, G.; Cifarelli, L.; Cindolo, F.; Clare, I.; Clare, R.; Coignet, G.; Colino, N.; Costantini, S.; de la Cruz, B.; Cucciarelli, S.; van Dalen, J.A.; de Asmundis, R.; Deglon, P.; Debreczeni, J.; Degre, A.; Dehmelt, K.; Deiters, K.; della Volpe, D.; Delmeire, E.; Denes, P.; DeNotaristefani, F.; De Salvo, A.; Diemoz, M.; Dierckxsens, M.; Dionisi, C.; Dittmar, M.; Doria, A.; Dova, M.T.; Duchesneau, D.; Duda, M.; Echenard, B.; Eline, A.; El Hage, A.; El Mamouni, H.; Engler, A.; Eppling, F.J.; Extermann, P.; Falagan, M.A.; Falciano, S.; Favara, A.; Fay, J.; Fedin, O.; Felcini, M.; Ferguson, T.; Fesefeldt, H.; Fiandrini, E.; Field, J.H.; Filthaut, F.; Fisher, P.H.; Fisher, W.; Fisk, I.; Forconi, G.; Freudenreich, K.; Furetta, C.; Galaktionov, Iouri; Ganguli, S.N.; Garcia-Abia, Pablo; Gataullin, M.; Gentile, S.; Giagu, S.; Gong, Z.F.; Grenier, Gerald Jean; Grimm, O.; Gruenewald, M.W.; Guida, M.; van Gulik, R.; Gupta, V.K.; Gurtu, A.; Gutay, L.J.; Haas, D.; Hatzifotiadou, D.; Hebbeker, T.; Herve, Alain; Hirschfelder, J.; Hofer, H.; Hohlmann, M.; Holzner, G.; Hou, S.R.; Hu, Y.; Jin, B.N.; Jones, Lawrence W.; de Jong, P.; Josa-Mutuberria, I.; Kaur, M.; Kienzle-Focacci, M.N.; Kim, J.K.; Kirkby, Jasper; Kittel, W.; Klimentov, A.; Konig, A.C.; Kopal, M.; Koutsenko, V.; Kraber, M.; Kraemer, R.W.; Kruger, A.; Kunin, A.; Ladron de Guevara, P.; Laktineh, I.; Landi, G.; Lebeau, M.; Lebedev, A.; Lebrun, P.; Lecomte, P.; Lecoq, P.; Le Coultre, P.; Le Goff, J.M.; Leiste, R.; Levtchenko, M.; Levtchenko, P.; Li, C.; Likhoded, S.; Lin, C.H.; Lin, W.T.; Linde, F.L.; Lista, L.; Liu, Z.A.; Lohmann, W.; Longo, E.; Lu, Y.S.; Luci, C.; Luminari, L.; Lustermann, W.; Ma, W.G.; Malgeri, L.; Malinin, A.; Mana, C.; Mans, J.; Martin, J.P.; Marzano, F.; Mazumdar, K.; McNeil, R.R.; Mele, S.; Merola, L.; Meschini, M.; Metzger, W.J.; Mihul, A.; Milcent, H.; Mirabelli, G.; Mnich, J.; Mohanty, G.B.; Muanza, G.S.; Muijs, A.J.M.; Musicar, B.; Musy, M.; Nagy, S.; Natale, S.; Napolitano, M.; Nessi-Tedaldi, F.; Newman, H.; Nisati, A.; Novak, T.; Kluge, Hannelies; Ofierzynski, R.; Organtini, G.; Pal, I.; Palomares, C.; Paolucci, P.; Paramatti, R.; Passaleva, G.; Patricelli, S.; Paul, Thomas Cantzon; Pauluzzi, M.; Paus, C.; Pauss, F.; Pedace, M.; Pensotti, S.; Perret-Gallix, D.; Petersen, B.; Piccolo, D.; Pierella, F.; Pioppi, M.; Piroue, P.A.; Pistolesi, E.; Plyaskin, V.; Pohl, M.; Pojidaev, V.; Pothier, J.; Prokofev, D.; Quartieri, J.; Rahal-Callot, G.; Rahaman, Mohammad Azizur; Raics, P.; Raja, N.; Ramelli, R.; Rancoita, P.G.; Ranieri, R.; Raspereza, A.; Razis, P.; Ren, D.; Rescigno, M.; Reucroft, S.; Riemann, S.; Riles, Keith; Roe, B.P.; Romero, L.; Rosca, A.; Rosemann, C.; Rosenbleck, C.; Rosier-Lees, S.; Roth, Stefan; Rubio, J.A.; Ruggiero, G.; Rykaczewski, H.; Sakharov, A.; Saremi, S.; Sarkar, S.; Salicio, J.; Sanchez, E.; Schafer, C.; Schegelsky, V.; Schopper, H.; Schotanus, D.J.; Sciacca, C.; Servoli, L.; Shevchenko, S.; Shivarov, N.; Shoutko, V.; Shumilov, E.; Shvorob, A.; Son, D.; Souga, C.; Spillantini, P.; Steuer, M.; Stickland, D.P.; Stoyanov, B.; Straessner, A.; Sudhakar, K.; Sultanov, G.; Sun, L.Z.; Sushkov, S.; Suter, H.; Swain, J.D.; Szillasi, Z.; Tang, X.W.; Tarjan, P.; Tauscher, L.; Taylor, L.; Tellili, B.; Teyssier, D.; Timmermans, Charles; Ting, Samuel C.C.; Ting, S.M.; Tonwar, S.C.; Toth, J.; Tully, C.; Tung, K.L.; Ulbricht, J.; Valente, E.; Van de Walle, R.T.; Vasquez, R.; Veszpremi, V.; Vesztergombi, G.; Vetlitsky, I.; Vicinanza, D.; Viertel, G.; Villa, S.; Vivargent, M.; Vlachos, S.; Vodopianov, I.; Vogel, H.; Vogt, H.; Vorobev, I.; Vorobyov, A.A.; Wadhwa, M.; Wang, Q.; Wang, X.L.; Wang, Z.M.; Weber, M.; Wilkens, H.; Wynhoff, S.; Xia, L.; Xu, Z.Z.; Yamamoto, J.; Yang, B.Z.; Yang, C.G.; Yang, H.J.; Yang, M.; Yeh, S.C.; Zalite, An.; Zalite, Yu.; Zhang, Z.P.; Zhao, J.; Zhu, G.Y.; Zhu, R.Y.; Zhuang, H.L.; Zichichi, A.; Zimmermann, B.; Zoller, M.

2004-01-01

The process e^+e^- --> Z gamma, where the Z boson decays into hadrons or neutrinos, is studied with data collected with the L3 detector at LEP at centre-of-mass energies from 189 GeV up to 209 GeV. The cross sections are measured and found to be in agreement with the Standard Model predictions. Limits on triple neutral-gauge-boson couplings, forbidden in the Standard Model at tree level, are derived. Limits on the energy scales at which the anomalous couplings could be manifest are set. They range from 0.3 TeV to 2.3 TeV depending on the new physics effect under consideration.

Transient simulation of an endothermic chemical process facility coupled to a high temperature reactor: Model development and validation

International Nuclear Information System (INIS)

Brown, Nicholas R.; Seker, Volkan; Revankar, Shripad T.; Downar, Thomas J.

2012-01-01

Highlights: ► Models for PBMR and thermochemical sulfur cycle based hydrogen plant are developed. ► Models are validated against available data in literature. ► Transient in coupled reactor and hydrogen plant system is studied. ► For loss-of-heat sink accident, temperature feedback within the reactor core enables shut down of the reactor. - Abstract: A high temperature reactor (HTR) is a candidate to drive high temperature water-splitting using process heat. While both high temperature nuclear reactors and hydrogen generation plants have high individual degrees of development, study of the coupled plant is lacking. Particularly absent are considerations of the transient behavior of the coupled plant, as well as studies of the safety of the overall plant. The aim of this document is to contribute knowledge to the effort of nuclear hydrogen generation. In particular, this study regards identification of safety issues in the coupled plant and the transient modeling of some leading candidates for implementation in the Nuclear Hydrogen Initiative (NHI). The Sulfur Iodine (SI) and Hybrid Sulfur (HyS) cycles are considered as candidate hydrogen generation schemes. Three thermodynamically derived chemical reaction chamber models are coupled to a well-known reference design of a high temperature nuclear reactor. These chemical reaction chamber models have several dimensions of validation, including detailed steady state flowsheets, integrated loop test data, and bench scale chemical kinetics. The models and coupling scheme are presented here, as well as a transient test case initiated within the chemical plant. The 50% feed flow failure within the chemical plant results in a slow loss-of-heat sink (LOHS) accident in the nuclear reactor. Due to the temperature feedback within the reactor core the nuclear reactor partially shuts down over 1500 s. Two distinct regions are identified within the coupled plant response: (1) immediate LOHS due to the loss of the sulfuric

Parallel processing implementation for the coupled transport of photons and electrons using OpenMP

Science.gov (United States)

Doerner, Edgardo

2016-05-01

In this work the use of OpenMP to implement the parallel processing of the Monte Carlo (MC) simulation of the coupled transport for photons and electrons is presented. This implementation was carried out using a modified EGSnrc platform which enables the use of the Microsoft Visual Studio 2013 (VS2013) environment, together with the developing tools available in the Intel Parallel Studio XE 2015 (XE2015). The performance study of this new implementation was carried out in a desktop PC with a multi-core CPU, taking as a reference the performance of the original platform. The results were satisfactory, both in terms of scalability as parallelization efficiency.

Thermo-hydro mechanical modeling in unsaturated hard clay: application to nuclear waste storage

International Nuclear Information System (INIS)

Jia, Y.

2006-07-01

This work presents an elastoplastic damage model for argillite in unsaturated conditions. A short resume of experimental investigations is presented in the first part. The results obtained show an important plastic deformation coupled with damage induced by initiation and growth of microcracks. Influences of water content on the mechanical behaviour are also investigated. Based on experimental data and micro-mechanical considerations, a general constitutive model is proposed for the poro-mechanical behavior of argillite in unsaturated conditions. The time dependent creep has also been incorporated in they model. The performance of the model is examined by comparing numerical simulation with experimental data in various load paths under saturated and unsaturated conditions. Finally, the model is applied to hydro-mechanical coupling study of the REP experiment and thermo-hydro-mechanical coupling study of the HE-D experiment. A good agreement is obtained between experimental data and numerical predictions. It has been shown that the proposed model describe correctly the main features of the mechanical behaviour of unsaturated rocks. (author)

Systemic couple therapy for dysthymia.

Science.gov (United States)

Montesano, Adrián; Feixas, Guillem; Muñoz, Dámaris; Compañ, Victoria

2014-03-01

We examined the effect of Systemic Couple Therapy on a patient diagnosed with dysthymic disorder and her partner. Marge and Peter, a middle-aged married couple, showed significant and meaningful changes in their pattern of interaction over the course of the therapy and, by the end of it, Marge no longer met the diagnostic criteria for dysthymic disorder. Her scores on the Structured Clinical Interview for DSM-IV Axis I Disorders (SCID-I) and Beck Depression Inventory, Second Edition (BDI-II) were in the clinical range before treatment and in the nonclinical one at the end of therapy. Although scores on Dyadic Adjustment Scale showed different patterns, both members reported significant improvement. The analysis of change in the alliance-related behaviors throughout the process concurred with change in couple's pattern of interaction. Treatment effects were maintained at 12-month follow-up. Highlights in the therapy process showed the importance of relational mechanisms of change, such as broadening the therapeutic focus into the couple's pattern of interaction, reducing expressed emotion and resentment, as well as increasing positive exchanges. The results of this evidence-based case study should prompt further investigation of couple therapy for dysthymia disorder. Randomized clinical trial design is needed to reach an evidence-based treatment status. (c) 2014 APA, all rights reserved.

Bioelectricity Generation and Bioremediation of an Azo-Dye in a Microbial Fuel Cell Coupled Activated Sludge Process

Science.gov (United States)

Khan, Mohammad Danish; Abdulateif, Huda; Ismail, Iqbal M.; Sabir, Suhail; Khan, Mohammad Zain

2015-01-01

Simultaneous bioelectricity generation and dye degradation was achieved in the present study by using a combined anaerobic-aerobic process. The anaerobic system was a typical single chambered microbial fuel cell (SMFC) which utilizes acid navy blue r (ANB) dye along with glucose as growth substrate to generate electricity. Four different concentrations of ANB (50, 100, 200 and 400 ppm) were tested in the SMFC and the degradation products were further treated in an activated sludge post treatment process. The dye decolorization followed pseudo first order kinetics while the negative values of the thermodynamic parameter ∆G (change in Gibbs free energy) shows that the reaction proceeds with a net decrease in the free energy of the system. The coulombic efficiency (CE) and power density (PD) attained peak values at 10.36% and 2,236 mW/m2 respectively for 200 ppm of ANB. A further increase in ANB concentrations results in lowering of cell potential (and PD) values owing to microbial inhibition at higher concentrations of toxic substrates. Cyclic voltammetry studies revealed a perfect redox reaction was taking place in the SMFC. The pH, temperature and conductivity remain 7.5–8.0, 27(±2°C and 10.6–18.2 mS/cm throughout the operation. The biodegradation pathway was studied by the gas chromatography coupled with mass spectroscopy technique, suggested the preferential cleavage of the azo bond as the initial step resulting in to aromatic amines. Thus, a combined anaerobic-aerobic process using SMFC coupled with activated sludge process can be a viable option for effective degradation of complex dye substrates along with energy (bioelectricity) recovery. PMID:26496083

Developing confidence in a coupled TH model based on the results of experiment by using engineering scale test facility, 'COUPLE'

International Nuclear Information System (INIS)

Fujisaki, Kiyoshi; Suzuki, Hideaki; Fujita, Tomoo

2008-03-01

It is necessary to understand quantitative changes of near-field conditions and processes over time and space for modeling the near-field evolution after emplacement of engineered barriers. However, the coupled phenomena in near-field are complicated because thermo-, hydro-, mechanical, chemical processes will interact each other. The question is, therefore, whether the applied model will represent the coupled behavior adequately or not. In order to develop confidence in the modeling, it is necessary to compare with results of coupled behavior experiments in laboratory or in site. In this report, we evaluated the applicability of a coupled T-H model under the conditions of simulated near-field for the results of coupled T-H experiment in laboratory. As a result, it has been shown that the fitting by the modeling with the measured data is reasonable under this condition. (author)

Coupling of Spinosad Fermentation and Separation Process via Two-Step Macroporous Resin Adsorption Method.

Science.gov (United States)

Zhao, Fanglong; Zhang, Chuanbo; Yin, Jing; Shen, Yueqi; Lu, Wenyu

2015-08-01

In this paper, a two-step resin adsorption technology was investigated for spinosad production and separation as follows: the first step resin addition into the fermentor at early cultivation period to decrease the timely product concentration in the broth; the second step of resin addition was used after fermentation to adsorb and extract the spinosad. Based on this, a two-step macroporous resin adsorption-membrane separation process for spinosad fermentation, separation, and purification was established. Spinosad concentration in 5-L fermentor increased by 14.45 % after adding 50 g/L macroporous at the beginning of fermentation. The established two-step macroporous resin adsorption-membrane separation process got the 95.43 % purity and 87 % yield for spinosad, which were both higher than that of the conventional crystallization of spinosad from aqueous phase that were 93.23 and 79.15 % separately. The two-step macroporous resin adsorption method has not only carried out the coupling of spinosad fermentation and separation but also increased spinosad productivity. In addition, the two-step macroporous resin adsorption-membrane separation process performs better in spinosad yield and purity.

Running couplings and operator mixing in the gravitational corrections to coupling constants

International Nuclear Information System (INIS)

Anber, Mohamed M.; Donoghue, John F.; El-Houssieny, Mohamed

2011-01-01

The use of a running coupling constant in renormalizable theories is well known, but the implementation of this idea for effective field theories with a dimensional coupling constant is, in general, less useful. Nevertheless, there are multiple attempts to define running couplings, including the effects of gravity, with varying conclusions. We sort through many of the issues involved, most particularly the idea of operator mixing and also the kinematics of crossing, using calculations in Yukawa and λφ 4 theories as illustrative examples. We remain in the perturbative regime. In some theories with a high permutation symmetry, such as λφ 4 , a reasonable running coupling can be defined. However, in most cases, such as Yukawa and gauge theories, a running coupling fails to correctly account for the energy dependence of the interaction strength. As a by-product we also contrast on-shell and off-shell renormalization schemes and show that operators which are normally discarded, such as those that vanish by the equations of motion, are required for off-shell renormalization of effective field theories. Our results suggest that the inclusion of gravity in the running of couplings is not useful or universal in the description of physical processes.

Multi-physical process and system analysis for geological underground repositories in clay formations in the post closure phase; Multiphysikalische Prozess- und Systemanalyse fuer geologische Tiefenlager im Tonsteingebirge in der Nachverschlussphase

Energy Technology Data Exchange (ETDEWEB)

Zhao, Juan

2017-09-21

In the framework of a safety case for repository systems in deep geological formations used for the disposal of high-level radioactive heat-generating waste, the THM-coupled long-term behaviour of such systems has to be analysed with consideration of 2-phase flow processes. These analyses are carried out for the repository near field and the isolating rock mass zone by performing numerical simulations, which require a sufficient process and system understanding with regard to the coupled physical processes involved and their interaction in the respective rock mass formation. The topic of this Ph.D. work is the analysis of the long-term system behaviour of a reference repository system built in clay stone rock mass. Therefore, numerical simulations have been carried out using the FTK-simulation tool which has been developed at the Chair in Waste Disposal and Geomechanics at the Clausthal University of Technology, in order to improve the process and system understanding for repository systems in the clay stone rock mass. In this context, the FTK-simulation tool is at first validated further by performing retrospective analyses of selected field and laboratory tests documented in the national and international literature, as well as of numerical simulation examples regarding the thermohydromechanical load-bearing behaviour of emplacement drifts. Besides, the FTK-simulation tool is used to perform a prognostic analysis concerning the laboratory investigations, which have been planned to qualitatively as well as quantitatively characterise the 2-phase flow properties of clay stone. In addition, a functional model approach is presented, which allows an abstract modeling of the secondary permeability development in the near field of drifts or shafts excavated and backfilled in clay stone rock mass as a function of the swelling pressure development in the bentonite backfill material. Finally, a comprehensive variation analysis is presented, which has been carried out for a

Processing of poly-Si electrodes for charge-coupled devices

Energy Technology Data Exchange (ETDEWEB)

Sherohman, J.W.; Cook, F.D.

1978-12-06

A technique has been developed to fabricate poly-Si electrodes for charge-coupled devices. By controlling the microstructure of a poly-Si film, an anisotropic etchant was selected to provide essentially uniform electrode width dimensions. The electrode widths have only a 6% variation for the majority of the devices over the area of a 2 inch silicon wafer.

Oil refinery wastewater treatment using coupled electrocoagulation and fixed film biological processes

Science.gov (United States)

Pérez, Laura S.; Rodriguez, Oscar M.; Reyna, Silvia; Sánchez-Salas, José Luis; Lozada, J. Daniel; Quiroz, Marco A.; Bandala, Erick R.

2016-02-01

Oil refinery wastewater was treated using a coupled treatment process including electrocoagulation (EC) and a fixed film aerobic bioreactor. Different variables were tested to identify the best conditions using this procedure. After EC, the effluent was treated in an aerobic biofilter. EC was capable to remove over 88% of the overall chemical oxygen demand (COD) in the wastewater under the best working conditions (6.5 V, 0.1 M NaCl, 4 electrodes without initial pH adjustment) with total petroleum hydrocarbon (TPH) removal slightly higher than 80%. Aluminum release from the electrodes to the wastewater was found an important factor for the EC efficiency and closely related with several operational factors. Application of EC allowed to increase the biodegradability of the sample from 0.015, rated as non-biodegradable, up to 0.5 widely considered as biodegradable. The effluent was further treated using an aerobic biofilter inoculated with a bacterial consortium including gram positive and gram negative strains and tested for COD and TPH removal from the EC treated effluent during 30 days. Cell count showed the typical bacteria growth starting at day three and increasing up to a maximum after eight days. After day eight, cell growth showed a plateau which agreed with the highest decrease on contaminant concentration. Final TPHs concentration was found about 600 mgL-1 after 30 days whereas COD concentration after biological treatment was as low as 933 mgL-1. The coupled EC-aerobic biofilter was capable to remove up to 98% of the total TPH amount and over 95% of the COD load in the oil refinery wastewater.

Relation between social information processing and intimate partner violence in dating couples.

Science.gov (United States)

Setchell, Sarah; Fritz, Patti Timmons; Glasgow, Jillian

2017-07-01

We used couple-level data to predict physical acts of intimate partner violence (IPV) from self-reported negative emotions and social information-processing (SIP) abilities among 100 dating couples (n = 200; mean age = 21.45 years). Participants read a series of hypothetical conflict situation vignettes and responded to questionnaires to assess negative emotions and various facets of SIP including attributions for partner behavior, generation of response alternatives, and response selection. We conducted a series of negative binomial mixed-model regressions based on the actor-partner interdependence model (APIM; Kenny, Kashy, & Cook, 2006, Dyadic data analysis. New York, NY: Guilford Press). There were significant results for the response generation and negative emotion models. Participants who generated fewer coping response alternatives were at greater risk of victimization (actor effect). Women were at greater risk of victimization if they had partners who generated fewer coping response alternatives (sex by partner interaction effect). Generation of less competent coping response alternatives predicted greater risk of perpetration among men, whereas generation of more competent coping response alternatives predicted greater risk of victimization among women (sex by actor interaction effects). Two significant actor by partner interaction effects were found for the negative emotion models. Participants who reported discrepant levels of negative emotions from their partners were at greatest risk of perpetration. Participants who reported high levels of negative emotions were at greatest risk of victimization if they had partners who reported low levels of negative emotions. This research has implications for researchers and clinicians interested in addressing the problem of IPV. Aggr. Behav. 43:329-341, 2017. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Coupled sulfur isotopic and chemical mass transfer modeling: Approach and application to dynamic hydrothermal processes

International Nuclear Information System (INIS)

Janecky, D.R.

1988-01-01

A computational modeling code (EQPSreverse arrowS) has been developed to examine sulfur isotopic distribution pathways coupled with calculations of chemical mass transfer pathways. A post processor approach to EQ6 calculations was chosen so that a variety of isotopic pathways could be examined for each reaction pathway. Two types of major bounding conditions were implemented: (1) equilibrium isotopic exchange between sulfate and sulfide species or exchange only accompanying chemical reduction and oxidation events, and (2) existence or lack of isotopic exchange between solution species and precipitated minerals, parallel to the open and closed chemical system formulations of chemical mass transfer modeling codes. All of the chemical data necessary to explicitly calculate isotopic distribution pathways is generated by most mass transfer modeling codes and can be input to the EQPS code. Routines are built in to directly handle EQ6 tabular files. Chemical reaction models of seafloor hydrothermal vent processes and accompanying sulfur isotopic distribution pathways illustrate the capabilities of coupling EQPSreverse arrowS with EQ6 calculations, including the extent of differences that can exist due to the isotopic bounding condition assumptions described above. 11 refs., 2 figs

MODELING COUPLED PROCESSES OF MULTIPHASE FLOW AND HEAT TRANSFER IN UNSATURATED FRACTURED ROCK

International Nuclear Information System (INIS)

Y. Wu; S. Mukhopadhyay; K. Zhang; G.S. Bodvarsson

2006-01-01

A mountain-scale, thermal-hydrologic (TH) numerical model is developed for investigating unsaturated flow behavior in response to decay heat from the radioactive waste repository at Yucca Mountain, Nevada, USA. The TH model, consisting of three-dimensional (3-D) representations of the unsaturated zone, is based on the current repository design, drift layout, and thermal loading scenario under estimated current and future climate conditions. More specifically, the TH model implements the current geological framework and hydrogeological conceptual models, and incorporates the most updated, best-estimated input parameters. This mountain-scale TH model simulates the coupled TH processes related to mountain-scale multiphase fluid flow, and evaluates the impact of radioactive waste heat on the hydrogeological system, including thermally perturbed liquid saturation, gas- and liquid-phase fluxes, and water and rock temperature elevations, as well as the changes in water flux driven by evaporation/condensation processes and drainage between drifts. For a better description of the ambient geothermal condition of the unsaturated zone system, the TH model is first calibrated against measured borehole temperature data. The ambient temperature calibration provides the necessary surface and water table boundary as well as initial conditions. Then, the TH model is used to obtain scientific understanding of TH processes in the Yucca Mountain unsaturated zone under the designed schedule of repository thermal load

Feedback control of chlorine inductively coupled plasma etch processing

International Nuclear Information System (INIS)

Lin Chaung; Leou, K.-C.; Shiao, K.-M.

2005-01-01

Feedback control has been applied to poly-Si etch processing using a chlorine inductively coupled plasma. Since the positive ion flux and ion energy incident upon the wafer surface are the key factors that influence the etch rate, the ion current and the root mean square (rms) rf voltage on the wafer stage, which are measured using an impedance meter connected to the wafer stage, are adopted as the controlled variables to enhance etch rate. The actuators are two 13.56 MHz rf power generators, which adjust ion density and ion energy, respectively. The results of closed-loop control show that the advantages of feedback control can be achieved. For example, with feedback control, etch rate variation under the transient chamber wall condition is reduced roughly by a factor of 2 as compared to the open-loop case. In addition, the capability of the disturbance rejection was also investigated. For a gas pressure variation of 20%, the largest etch rate variation is about 2.4% with closed-loop control as compared with as large as about 6% variation using open-loop control. Also the effect of ion current and rms rf voltage on etch rate was studied using 2 2 factorial design whose results were used to derive a model equation. The obtained formula was used to adjust the set point of ion current and rf voltage so that the desired etch rate was obtained

Optimization of a Coupling Process for Insulin Degludec According to a Quality by Design (QbD) Paradigm.

Science.gov (United States)

Nie, Lei; Hu, Mingming; Yan, Xu; Guo, Tingting; Wang, Haibin; Zhang, Sheng; Qu, Haibin

2018-05-03

This case study described a successful application of the quality by design (QbD) principles to a coupling process development of insulin degludec. Failure mode effects analysis (FMEA) risk analysis was first used to recognize critical process parameters (CPPs). Five CPPs, including coupling temperature (Temp), pH of desB30 solution (pH), reaction time (Time), desB30 concentration (Conc), and molar equivalent of ester per mole of desB30 insulin (MolE), were then investigated using a fractional factorial design. The curvature effect was found significant, indicating the requirement of second-order models. Afterwards, a central composite design was built with an augmented star and center points study. Regression models were developed for the CPPs to predict the purity and yield of predegludec using above experimental data. The R 2 and adjusted R 2 were higher than 96 and 93% for the two models respectively. The Q 2 values were more than 80% indicating a good predictive ability of models. MolE was found to be the most significant factor affecting both yield and purity of predegludec. Temp, pH, and Conc were also significant for predegludec purity, while Time appeared to remarkably influence the yield model. The multi-dimensional design space and normal operating region (NOR) with a robust setpoint were determined using a probability-based Monte-Carlo simulation method. The verified experimental results showed that the design space was reliable and effective. This study enriches the understanding of acetylation process and is instructional to other complicated operations in biopharmaceutical engineering.

Discrete and continuum approaches for the analysis of coupled thermal-mechanical processes in the near field of a HLW repository

International Nuclear Information System (INIS)

Shimizu, Hiroyuki; Fujita, Tomoo; Nakama, Shigeo; Koyama, Tomofumi; Chijimatsu, Masakazu

2011-01-01

This paper reports on the results of the numerical simulations for the analysis of coupled thermal-mechanical processes in the near field of a HLW repository using Finite Element Method (FEM) and Distinct Element Method (DEM). The FEM approach provides quantitative information of the change of stress during excavation and heating process. On the other hand, the DEM approach shows the crack propagation process at the borehole surface, and this result agrees qualitatively well with the experimental observation. By comparing these results obtained from both approaches, quantitative and qualitative insights into various aspects of the processes occurred in the near field can be obtained. (author)

Coupling Computer-Aided Process Simulation and ...

Science.gov (United States)

A methodology is described for developing a gate-to-gate life cycle inventory (LCI) of a chemical manufacturing process to support the application of life cycle assessment in the design and regulation of sustainable chemicals. The inventories were derived by first applying process design and simulation of develop a process flow diagram describing the energy and basic material flows of the system. Additional techniques developed by the U.S. Environmental Protection Agency for estimating uncontrolled emissions from chemical processing equipment were then applied to obtain a detailed emission profile for the process. Finally, land use for the process was estimated using a simple sizing model. The methodology was applied to a case study of acetic acid production based on the Cativa tm process. The results reveal improvements in the qualitative LCI for acetic acid production compared to commonly used databases and top-down methodologies. The modeling techniques improve the quantitative LCI results for inputs and uncontrolled emissions. With provisions for applying appropriate emission controls, the proposed method can provide an estimate of the LCI that can be used for subsequent life cycle assessments. As part of its mission, the Agency is tasked with overseeing the use of chemicals in commerce. This can include consideration of a chemical's potential impact on health and safety, resource conservation, clean air and climate change, clean water, and sustainable

24/7 Negotiation in couples' transition to parenthood

NARCIS (Netherlands)

Wiesmann, S.M.

2010-01-01

How do couples negotiate about their division of paid and unpaid work when they become parents? The division of work among couples has significantly changed in the past decades. This study focused on the underlying processes that lead couples to a certain division of paid and unpaid work. To unravel

Étude numérique du couplage thermohydromécanique dans les roches. Influence des termes de couplage non linéaires pour un matériau isotrope linéaire Numerical Analysis of a Thermohydromechanical Coupling in Rocks. Influence of Nonlinear Coupling Terms on a Linear Isotropic Material

Directory of Open Access Journals (Sweden)

Henry J. P.

2006-11-01

Full Text Available Nous présentons dans ce travail une étude numérique basée sur la méthode des éléments finis, du comportement thermoporoélastique de certaines roches. Les trois effets de couplage : déformabilité de la roche, pression interstitielle et température sont pris en compte simultanément dans la résolution numérique. Une application simple sur un puits pétrolier en conditions axisymétriques est finalement présentée afin de dégager en particulier l'influence du terme de couplage convectif non linéaire, obtenu dans l'équation de diffusivité thermique, sur l'évolution de la température et de la pression interstitielle autour du forage. This article describes a finite-element method for solving the problem of nonlinear coupling between interstitial pressure and temperature during stress on a poroelastic rock. Such coupling phenomena occur during massive injection of cold water into a petroleum borehole for example. The implementation of such a numerical solution, used here with the assumption of small deformations, first requires a review of the behavior law of the material (Eq. 2. 2 and of the equations for hydraulic diffusivity (Eq. 2. 3 and thermal diffusivity (Eq. 2. 4. This last equation (2. 4 is the one containing the nonlinear coupling terms in Grad P Grad P and Grad T. Grad P. During simulation of flow at a high flow rate, these products can no longer be neglected as shown by the results in Fig. 2. The variational formulation of the problem is then determined in relation to the three equations for equilibrium, thermal diffusivity and hydraulic diffusivity. After geometric and temporal discretizations, this formulation leads to a finite-element calculating scheme resulting in the simultaneous solving of all three equations. This solution, based on the inversion of the system of equations (2. 15, requires the updating of the rigidity matrix at each time step to take nonlinear coupling into consideration. Calculations with an

COUPLING MEASUREMENT AND CORRECTION AT RHIC

International Nuclear Information System (INIS)

PILAT, F.; BEEBE-WANG, J.; FISCHER, W.; PTITSYN, V.; SATOGATA, T.

2002-01-01

Coupling correction at RHIC has been operationally achieved through a two-step process: using local triplet skew quadrupoles to compensate coupling corn rolled low-beta triplet quadrupoles, and minimizing the tune separation and residual coupling with orthogonal global skew quadrupole families. An application has been developed for global correction that allows skew quadrupole tuning and tune display with a choice of different tune measurement techniques, including tune-meter, Schottky and phase lock loop (PLL). Coupling effects have been analyzed by using 1024-turn (TBT) information from the beam position monitor (BPM) system. These data allow the reconstruction of the off-diagonal terms of the transfer matrix, a measure of global coupling. At both injection and storage energies, coordination of tune meter kicks with TBT acquisition at 322 BPW's in each ring allows the measurement of local coupling at all BPM locations

A risk management process for reinforced concrete structures by coupling modelling, monitoring and Bayesian approaches

International Nuclear Information System (INIS)

Capra, Bruno; Li, Kefei; Wolff, Valentin; Bernard, Olivier; Gerard, Bruno

2004-01-01

The impact of steel corrosion on the durability of reinforced concrete structures has since a long time been a major concern in civil engineering. The main electrochemical mechanisms of the steel corrosion are know well known. The material and structure degradation is attributed to the progressive formation of an expansive corrosion product at the steel-concrete interface. To assess quantitatively the structure lifetime, a two-stage service life model has been accepted widely. So far, the research attention is mainly given to the corrosion in an un-cracked concrete. However. practically one is often confronted to the reinforcement corrosion in an already cracked concrete. How to quantify the corrosion risk is of great interest for the long term durability of these cracked structures. To this end, this paper proposes a service life modeling for the corrosion process by carbonation in a cracked or un-cracked concrete depending on the observation or monitoring data available. Some recent experimental investigations are used to calibrate the models. Then, the models are applied to a shell structure to quantify the corrosion process and determine the optimal maintenance strategy. As corrosion processes are very difficult to model and subjected to material and environmental random variations, an example of structure reassessment is presented taking into account in situ information by the mean of Bayesian approaches. The coupling of monitoring, modelling and updating leads to a new global maintenance strategy of infrastructure. In conclusion: This paper presents an unified methodology coupling predictive models, observations and Bayesian approaches in order to assess the degradation degree of an ageing structure. The particular case of corrosion is treated on an innovative way by the development of a service life model taking into account cracking effects on the kinetics of the phenomena. At a material level, the dominant factors are the crack opening and the crack nature

Quadrature squeezing of a mechanical resonator generated by the electromechanical coupling with two coupled quantum dots

Energy Technology Data Exchange (ETDEWEB)

Yan, Yan [Department of Physics, Huazhong Normal University, Wuhan (China); School of Physics and Optoelectronic Engineering, Yangtze University, Jingzhou (China); Zhu, Jia-pei [Department of Physics, Honghe University, Mengzi (China); Zhao, Shao-ming; Li, Gao-xiang [Department of Physics, Huazhong Normal University, Wuhan (China)

2015-01-01

The quadrature squeezing of a mechanical resonator (MR) coupled with two quantum dots (QDs) through the electromechanical coupling, where the QDs are driven by a strong and two weak laser fields is investigated. By tuning the gate voltage, the electron can be trapped in a quantum pure state. Under certain conditions, the discrepancies between the transition frequency and that of two weak fields are compensated by the phonons induced by the electromechanical coupling of the MR with QDs. In this case, some dissipative processes occur resonantly. The phonons created and (or) annihilated in these dissipative processes are correlated thus leading to the quadrature squeezing of the MR. A squeezed vacuum reservoir for the MR is built up. By tuning the gate voltage to control the energy structure of the QDs, the present squeezing scheme has strong resistance against the dephasing processes of the QDs in low temperature limit. The role of the temperature of the phonon reservoir is to damage squeezing of the MR. (copyright 2014 by WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Fenton Process Coupled to Ultrasound and UV Light Irradiation for the Oxidation of a Model Pollutant

Directory of Open Access Journals (Sweden)

Karen E. Barrera-Salgado

2016-01-01

Full Text Available The Fenton process coupled to photosonolysis (UV light and Us, using Fe2O3 catalyst supported on Al2O3, was used to oxidize a model pollutant like acid green 50 textile dye (AG50. Dye degradation was followed by AG50 concentration decay analyses. It was observed that parameters like iron content on a fixed amount of catalyst supporting material, catalyst annealing temperature, initial dye concentration, and the solution pH influence the overall treatment efficiency. High removal efficiencies of the model pollutant are achieved. The stability and reusability tests of the Fe2O3 catalyst show that the catalyst can be used up to three cycles achieving high discoloration. Thus, this catalyst is highly efficient for the degradation of AG50 in the Fenton process.

NRC's geotechnical engineering research needs for the high-level waste repository program

International Nuclear Information System (INIS)

Gupta, D.C.; Philip, J.; Lorig, L.J.; Chowdhury, A.H.

1992-01-01

To develop the capability for independently assessing the US Department of Energy's (DOE's) geologic repository design within a limited time, the US Nuclear Regulatory Commission (NRC) staff needs to perform certain research well before receiving the license application. The NRC staff is using a number of factors to identify the areas that it needs to research. The staff assigns priorities to the needed research based on programmatic considerations and the significance of the work. In the geotechnical engineering field, the staff is conducting research in the following three areas: response of the repository to repeated strong ground motion, rock-mass sealing, and coupled thermo-hydro-mechanical interactions. In this paper, the NRC staff also presents the areas of additional research needed in the geotechnical engineering field

Two coupled Lévy queues with independent input

OpenAIRE

Jevgenijs Ivanovs; Onno Boxma

2014-01-01

We consider a pair of coupled queues driven by independent spectrally-positive Lévy processes. With respect to the bi-variate workload process this framework includes both the coupled processor model and the two-server fluid network with independent Lévy inputs. We identify the joint transform of the stationary workload distribution in terms of Wiener-Hopf factors corresponding to two auxiliary Lévy processes with explicit Laplace exponents. We reinterpret and extend the ideas of Cohen and Bo...

Single-Run Single-Mask Inductively-Coupled-Plasma Reactive-Ion-Etching Process for Fabricating Suspended High-Aspect-Ratio Microstructures

Science.gov (United States)

Yang, Yao-Joe; Kuo, Wen-Cheng; Fan, Kuang-Chao

2006-01-01

In this work, we present a single-run single-mask (SRM) process for fabricating suspended high-aspect-ratio structures on standard silicon wafers using an inductively coupled plasma-reactive ion etching (ICP-RIE) etcher. This process eliminates extra fabrication steps which are required for structure release after trench etching. Released microstructures with 120 μm thickness are obtained by this process. The corresponding maximum aspect ratio of the trench is 28. The SRM process is an extended version of the standard process proposed by BOSCH GmbH (BOSCH process). The first step of the SRM process is a standard BOSCH process for trench etching, then a polymer layer is deposited on trench sidewalls as a protective layer for the subsequent structure-releasing step. The structure is released by dry isotropic etching after the polymer layer on the trench floor is removed. All the steps can be integrated into a single-run ICP process. Also, only one mask is required. Therefore, the process complexity and fabrication cost can be effectively reduced. Discussions on each SRM step and considerations for avoiding undesired etching of the silicon structures during the release process are also presented.

The Effects of a Couples-Based Health Behavior Intervention During Pregnancy on Latino Couples' Dyadic Satisfaction Postpartum.

Science.gov (United States)

Coop Gordon, Kristina; Roberson, Patricia N E; Hughes, Jessica A; Khaddouma, Alexander M; Swamy, Geeta K; Noonan, Devon; Gonzalez, Alicia M; Fish, Laura; Pollak, Kathryn I

2018-03-30

Many couples tend to report steadily decreasing relationship quality following the birth of a child. However, little is known about the postpartum period for Latino couples, a rapidly growing ethnic group who are notably underserved by mental and physical health caregivers in the United States. Thus, this study investigated whether a brief couples' intervention focused on helping couples support each other while increasing healthy behaviors might improve dyadic functioning postpartum. This study presents secondary analyses of data regarding couple functioning from a larger randomized controlled trial with 348 Latino couples to promote smoking cessation. Portions of the intervention taught the couple communication and problem-solving skills to increase healthy behavior. Couples participated in four face-to-face assessments across 1 year starting at the end of the first trimester. Latent growth curve analyses revealed that the treatment group reported an increase in relationship satisfaction and constructive communication after the intervention, which diminished by 1-year follow-up, returning couples to their baseline levels of satisfaction. Results suggest that incorporating a brief couple intervention as part of a larger health intervention for Latinos may prevent postpartum decreases in relationship satisfaction. © 2018 Family Process Institute.

Enhancing the Relationship Adjustment of South Asian Canadian Couples Using a Systemic-Constructivist Approach to Couple Therapy.

Science.gov (United States)

Ahmad, Saunia; Reid, David W

2016-10-01

The effectiveness of systemic-constructivist couple therapy (SCCT) in improving the relationship adjustment of South Asian Canadian couples in ways that attend to their culture was evaluated. The SCCT interventions engage partners in reflexive processing of both their own and their partner's ways of construing, and the reciprocity between these two. A core change mechanism of SCCT, couple identity ("we-ness"), that connotes the ability for thinking and experiencing relationally, was coded from verbatim transcripts of partners' within-session dialogue. As predicted, South Asian partners' relationship adjustment improved significantly from the first to final session of SCCT, and concurrent increases in each partner's couple identity mediated such improvements. The implications for considering culture and couple identity in couple therapy are discussed. Video Abstract is found in the online version of the article. © 2016 American Association for Marriage and Family Therapy.

Development of an experimental approach to study coupled soil-plant-atmosphere processes using plant analogs

Science.gov (United States)

Trautz, Andrew C.; Illangasekare, Tissa H.; Rodriguez-Iturbe, Ignacio; Heck, Katharina; Helmig, Rainer

2017-04-01

The atmosphere, soils, and vegetation near the land-atmosphere interface are in a state of continuous dynamic interaction via a myriad of complex interrelated feedback processes which collectively, remain poorly understood. Studying the fundamental nature and dynamics of such processes in atmospheric, ecological, and/or hydrological contexts in the field setting presents many challenges; current experimental approaches are an important factor given a general lack of control and high measurement uncertainty. In an effort to address these issues and reduce overall complexity, new experimental design considerations (two-dimensional intermediate-scale coupled wind tunnel-synthetic aquifer testing using synthetic plants) for studying soil-plant-atmosphere continuum soil moisture dynamics are introduced and tested in this study. Validation of these experimental considerations, particularly the adoption of synthetic plants, is required prior to their application in future research. A comparison of three experiments with bare soil surfaces or transplanted with a Stargazer lily/limestone block was used to evaluate the feasibility of the proposed approaches. Results demonstrate that coupled wind tunnel-porous media experimentation, used to simulate field conditions, reduces complexity, and enhances control while allowing fine spatial-temporal resolution measurements to be made using state-of-the-art technologies. Synthetic plants further help reduce system complexity (e.g., airflow) while preserving the basic hydrodynamic functions of plants (e.g., water uptake and transpiration). The trends and distributions of key measured atmospheric and subsurface spatial and temporal variables (e.g., soil moisture, relative humidity, temperature, air velocity) were comparable, showing that synthetic plants can be used as simple, idealized, nonbiological analogs for living vegetation in fundamental hydrodynamic studies.

Coupled geochemical and solute transport code development

International Nuclear Information System (INIS)

Morrey, J.R.; Hostetler, C.J.

1985-01-01

A number of coupled geochemical hydrologic codes have been reported in the literature. Some of these codes have directly coupled the source-sink term to the solute transport equation. The current consensus seems to be that directly coupling hydrologic transport and chemical models through a series of interdependent differential equations is not feasible for multicomponent problems with complex geochemical processes (e.g., precipitation/dissolution reactions). A two-step process appears to be the required method of coupling codes for problems where a large suite of chemical reactions must be monitored. Two-step structure requires that the source-sink term in the transport equation is supplied by a geochemical code rather than by an analytical expression. We have developed a one-dimensional two-step coupled model designed to calculate relatively complex geochemical equilibria (CTM1D). Our geochemical module implements a Newton-Raphson algorithm to solve heterogeneous geochemical equilibria, involving up to 40 chemical components and 400 aqueous species. The geochemical module was designed to be efficient and compact. A revised version of the MINTEQ Code is used as a parent geochemical code

Couples Therapy: An Adlerian Perspective.

Science.gov (United States)

Kern, Roy M.; And Others

This book provides therapists with a theoretical base from which to view the dynamics of couples' relationships and the therapeutic process. The book's eight chapters are organized into three parts: "Adlerian Theory and Process"; "Therapeutic Interventions"; and "Special Issues in Marital Therapy." Chapter 1, Adlerian…

Marital Processes Linking Gender Role Attitudes and Marital Satisfaction Among Mexican-Origin Couples: Application of an Actor-Partner Interdependence Mediation Model.

Science.gov (United States)

Helms, Heather M; Supple, Andrew J; Hengstebeck, Natalie D; Wood, Claire A; Rodriguez, Yuliana

2018-01-24

Informed by dyadic approaches and culturally informed, ecological perspectives of marriage, we applied an actor-partner interdependence mediation model (APIMeM) in a sample of 120 Mexican-origin couples to examine (a) the associations linking Mexican immigrant husbands' and wives' gender role attitudes to marital satisfaction directly and indirectly through marital processes (i.e., warmth and negativity) and (b) whether the associations between spouses' gender role attitudes and marital processes were moderated by wives' employment. Although previous research has identified spouses' gender role attitudes as potential predictors of spouses' marital satisfaction, no study has examined these links in a dyadic model that elucidates how gender role attitudes may operate through processes to shape marital satisfaction and conditions under which associations may differ. We found that when spouses reported less sex-typed attitudes, their partners reported feeling more connected to them and more satisfied with the marriage, regardless of whether wives were employed. Our results suggest that marital satisfaction was highest for those Mexican-origin couples in which marital partners were less sex-typed in their attitudes about marital roles to the extent that partners' attitudinal role flexibility promoted spouses' feelings of warmth and connection to their partner. © 2018 Family Process Institute.

Impact of atmospheric model resolution on simulation of ENSO feedback processes: a coupled model study

Science.gov (United States)

Hua, Lijuan; Chen, Lin; Rong, Xinyao; Su, Jingzhi; Wang, Lu; Li, Tim; Yu, Yongqiang

2018-03-01

This study examines El Niño-Southern Oscillation (ENSO)-related air-sea feedback processes in a coupled general circulation model (CGCM) to gauge model errors and pin down their sources in ENSO simulation. Three horizontal resolutions of the atmospheric component (T42, T63 and T106) of the CGCM are used to investigate how the simulated ENSO behaviors are affected by the resolution. We find that air-sea feedback processes in the three experiments mainly differ in terms of both thermodynamic and dynamic feedbacks. We also find that these processes are simulated more reasonably in the highest resolution version than in the other two lower resolution versions. The difference in the thermodynamic feedback arises from the difference in the shortwave-radiation (SW) feedback. Due to the severely (mildly) excessive cold tongue in the lower (higher) resolution version, the SW feedback is severely (mildly) underestimated. The main difference in the dynamic feedback processes lies in the thermocline feedback and the zonal-advection feedback, both of which are caused by the difference in the anomalous thermocline response to anomalous zonal wind stress. The difference in representing the anomalous thermocline response is attributed to the difference in meridional structure of zonal wind stress anomaly in the three simulations, which is linked to meridional resolution.

Life cycle assessment of coupling household biogas production to agricultural industry: A case study of biogas-linked persimmon cultivation and processing system

International Nuclear Information System (INIS)

Chen, Bin; Chen, Shaoqing

2013-01-01

Biogas plant construction has been boosted in rural China not only due to the immediate merit from biogas production but also the succeeding benefit from by-product utilization in agro-industry, both of which are significant strategies to address energy shortage and global warming issues. However, little work has been done to evaluate the coupling of biogas projects to traditional agrosystems from a life-cycle perspective, which is most important in process and system optimization in different senses. By taking persimmon cultivation and processing with supports from a household biogas plant as a case study, this study conducts a life cycle assessment of coupling biogas production to agro-industry in terms of energy, environmental and economic performance. The results suggest that each production stage following the biogas/digestate utilization chain (biogas operation-persimmon cultivation-product processing) is beneficial across all three aspects. However, a tradeoff only exists in utilizing digestate as top-dressing and employing biogas utilization as engine fuel, while biogas application in fresh-keeping and digestate reuse as base fertilizer fails to increase either energy production or greenhouse gas mitigation. The coupled system can be hopefully optimized through increasing fermentation efficiency and joint operation of biogas digesters. -- Highlights: •Biogas/digestate utilization is overall beneficial in all production stages. •Each bioresource application may not be profitable in all respects. •Tradeoffs in using biogas and digestate vary among different utilization ways. •Multi-user operation and fermentation efficiency elevation optimize system

The Aster code; Code Aster

Energy Technology Data Exchange (ETDEWEB)

Delbecq, J.M

1999-07-01

The Aster code is a 2D or 3D finite-element calculation code for structures developed by the R and D direction of Electricite de France (EdF). This dossier presents a complete overview of the characteristics and uses of the Aster code: introduction of version 4; the context of Aster (organisation of the code development, versions, systems and interfaces, development tools, quality assurance, independent validation); static mechanics (linear thermo-elasticity, Euler buckling, cables, Zarka-Casier method); non-linear mechanics (materials behaviour, big deformations, specific loads, unloading and loss of load proportionality indicators, global algorithm, contact and friction); rupture mechanics (G energy restitution level, restitution level in thermo-elasto-plasticity, 3D local energy restitution level, KI and KII stress intensity factors, calculation of limit loads for structures), specific treatments (fatigue, rupture, wear, error estimation); meshes and models (mesh generation, modeling, loads and boundary conditions, links between different modeling processes, resolution of linear systems, display of results etc..); vibration mechanics (modal and harmonic analysis, dynamics with shocks, direct transient dynamics, seismic analysis and aleatory dynamics, non-linear dynamics, dynamical sub-structuring); fluid-structure interactions (internal acoustics, mass, rigidity and damping); linear and non-linear thermal analysis; steels and metal industry (structure transformations); coupled problems (internal chaining, internal thermo-hydro-mechanical coupling, chaining with other codes); products and services. (J.S.)

The Aster code

International Nuclear Information System (INIS)

Delbecq, J.M.

1999-01-01

The Aster code is a 2D or 3D finite-element calculation code for structures developed by the R and D direction of Electricite de France (EdF). This dossier presents a complete overview of the characteristics and uses of the Aster code: introduction of version 4; the context of Aster (organisation of the code development, versions, systems and interfaces, development tools, quality assurance, independent validation); static mechanics (linear thermo-elasticity, Euler buckling, cables, Zarka-Casier method); non-linear mechanics (materials behaviour, big deformations, specific loads, unloading and loss of load proportionality indicators, global algorithm, contact and friction); rupture mechanics (G energy restitution level, restitution level in thermo-elasto-plasticity, 3D local energy restitution level, KI and KII stress intensity factors, calculation of limit loads for structures), specific treatments (fatigue, rupture, wear, error estimation); meshes and models (mesh generation, modeling, loads and boundary conditions, links between different modeling processes, resolution of linear systems, display of results etc..); vibration mechanics (modal and harmonic analysis, dynamics with shocks, direct transient dynamics, seismic analysis and aleatory dynamics, non-linear dynamics, dynamical sub-structuring); fluid-structure interactions (internal acoustics, mass, rigidity and damping); linear and non-linear thermal analysis; steels and metal industry (structure transformations); coupled problems (internal chaining, internal thermo-hydro-mechanical coupling, chaining with other codes); products and services. (J.S.)

Characterisation of Ground Thermal and Thermo-Mechanical Behaviour for Shallow Geothermal Energy Applications

Directory of Open Access Journals (Sweden)

Ana Vieira

2017-12-01

Full Text Available Increasing use of the ground as a thermal reservoir is expected in the near future. Shallow geothermal energy (SGE systems have proved to be sustainable alternative solutions for buildings and infrastructure conditioning in many areas across the globe in the past decades. Recently novel solutions, including energy geostructures, where SGE systems are coupled with foundation heat exchangers, have also been developed. The performance of these systems is dependent on a series of factors, among which the thermal properties of the soil play a major role. The purpose of this paper is to present, in an integrated manner, the main methods and procedures to assess ground thermal properties for SGE systems and to carry out a critical review of the methods. In particular, laboratory testing through either steady-state or transient methods are discussed and a new synthesis comparing results for different techniques is presented. In situ testing including all variations of the thermal response test is presented in detail, including a first comparison between new and traditional approaches. The issue of different scales between laboratory and in situ measurements is then analysed in detail. Finally, the thermo-hydro-mechanical behaviour of soil is introduced and discussed. These coupled processes are important for confirming the structural integrity of energy geostructures, but routine methods for parameter determination are still lacking.

Examining the Individual and Dyadic Coping Processes of Men and Women in Infertile Couples and Their Relationship to Infertility Stress, Marital Adjustment, and Depression

OpenAIRE

Peterson, Brennan Daniel

2002-01-01

This study explored the individual and dyadic coping processes of men and women in infertile couples and their relationship to infertility stress, marital adjustment, and depression. Study participants were comprised of 1,026 men and women (420 of which were couples) who were referred to a university-affiliated teaching hospital for advanced reproductive treatments between the years of 1991 and 2001. Three months prior to treatment, participants completed the Ways of Coping Questionnaire (W...

Coupled Photonic Crystal Cavity Array Laser

DEFF Research Database (Denmark)

Schubert, Martin

in the quadratic lattice. Processing techniques are developed and optimized in order fabricate photonic crystals membranes in gallium arsenide with quantum dots as gain medium and in indium gallium arsenide phosphide with quantum wells as gain medium. Several key issues in process to ensure good quality....... The results are in good agreement with standard coupled mode theory. Also a novel type of photonic crystal structure is proposed called lambda shifted cavity which is a twodimensional photonic crystal laser analog of a VCSEL laser. Detailed measurements of the coupled modes in the photonic crystals...... with quantum dots are carried out. In agreement with a simple gain model the structures do not show stimulated emission. The spectral splitting due to the coupling between single cavities as well as arrays of cavities is studied theoretically and experimentally. Lasing is observed for photonic crystal cavity...

Effect of granular activated carbon addition on the effluent properties and fouling potentials of membrane-coupled expanded granular sludge bed process.

Science.gov (United States)

Ding, An; Liang, Heng; Qu, Fangshu; Bai, Langming; Li, Guibai; Ngo, Huu Hao; Guo, Wenshan

2014-11-01

To mitigate membrane fouling of membrane-coupled anaerobic process, granular activated carbon (GAC: 50 g/L) was added into an expanded granular sludge bed (EGSB). A short-term ultrafiltration test was investigated for analyzing membrane fouling potential and underlying fouling mechanisms. The results showed that adding GAC into the EGSB not only improved the COD removal efficiency, but also alleviated membrane fouling efficiently because GAC could help to reduce soluble microbial products, polysaccharides and proteins by 26.8%, 27.8% and 24.7%, respectively, compared with the control system. Furthermore, excitation emission matrix (EEM) fluorescence spectroscopy analysis revealed that GAC addition mainly reduced tryptophan protein-like, aromatic protein-like and fulvic-like substances. In addition, the resistance distribution analysis demonstrated that adding GAC primarily decreased the cake layer resistance by 53.5%. The classic filtration mode analysis showed that cake filtration was the major fouling mechanism for membrane-coupled EGSB process regardless of the GAC addition. Copyright © 2014 Elsevier Ltd. All rights reserved.

Use of the available energy in the re-gasification process of liquefied natural gas by coupling combined heat and power cycles

Energy Technology Data Exchange (ETDEWEB)

Sgarbi, P.V.; Schmeda Lopez, D.R.; Indrusiak, M.L.S.; Schneider, P. Smith [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Dept. of Mechanical Engineering], Emails: guetuso@gmail.com, diego.schmeda@ufrgs.br, sperbindrusiak@via-rs.net, pss@mecanica.ufrgs.br

2009-07-01

This work evaluates the possibilities of taking advantage of the heat transferred in the re-gasification process of liquid natural gas (LNG). It is proposed the coupling of a Brayton-Rankine combined heat and power plant (CHP) to a LNG re-gasification plant in order to use the heat involved in this process as cold source for the CHP plant. For comparison, the same CHP is simulated exchanging heat with a reference environment. An analysis is performed assuming that the amount of natural gas fed to the Brayton sub-cycle combustion chamber is equal for both cases. The CHP coupled to the re-gasification plant present a net power generation of 22.7 MW and the efficiency is 45.5%. It represents a gain of 2.98 MW in the power generation and 15% in the cycle efficiency, when compared to the reference cycle. The exergetic efficiency with this proposal is 49.3%, which is 9% higher than the reference cycle. (author)

Development of a global 1-D chemically radiatively coupled model and an introduction to the development of a chemically coupled General Circulation Model

International Nuclear Information System (INIS)

Akiyoshi, H.

1997-01-01

A global one-dimensional, chemically and radiatively coupled model has been developed. The basic concept of the coupled model, definition of globally averaged zenith angles, the formulation of the model chemistry, radiation, the coupled processes, and profiles and diurnal variations of temperature and chemical species at a normal steady state are presented. Furthermore, a suddenly doubled CO 2 experiment and a Pinatubo aerosol increase experiment were performed with the model. The time scales of variations in ozone and temperature in the lower stratosphere of the coupled system in the doubled CO 2 experiment was long, due to a feedback process among ultra violet radiation, O(1D), NO y , NO x , and O 3 . From the Pinatubo aerosol experiment, a delay of maximum ozone decrease from the maximum aerosol loading is shown and discussed. Developments of 3-D chemical models with coupled processes are briefly described, and the ozone distribution from the first version of the 3-D model are presented. Chemical model development in National Institute for Environmental Studies (NIES) are briefly described. (author)

Exchange bias in nearly perpendicularly coupled ferromagnetic/ferromagnetic system

International Nuclear Information System (INIS)

Bu, K.M.; Kwon, H.Y.; Oh, S.W.; Won, C.

2012-01-01

Exchange bias phenomena appear not only in ferromagnetic/antiferromagnetic systems but also in ferromagnetic/ferromagnetic systems in which two layers are nearly perpendicularly coupled. We investigated the origin of the symmetry-breaking mechanism and the relationship between the exchange bias and the system's energy parameters. We compared the results of computational Monte Carlo simulations with those of theoretical model calculation. We found that the exchange bias exhibited nonlinear behaviors, including sign reversal and singularities. These complicated behaviors were caused by two distinct magnetization processes depending on the interlayer coupling strength. The exchange bias reached a maximum at the transition between the two magnetization processes. - Highlights: ► Exchange bias phenomena are found in perpendicularly coupled F/F systems. ► Exchange bias exhibits nonlinear behaviors, including sign reversal and singularities. ► These complicated behaviors were caused by two distinct magnetization processes. ► Exchange bias reached a maximum at the transition between the two magnetization processes. ► We established an equation to maximize the exchange bias in perpendicularly coupled F/F system.

Slower speed and stronger coupling: adaptive mechanisms of chaos synchronization.

Science.gov (United States)

Wang, Xiao Fan

2002-06-01

We show that two initially weakly coupled chaotic systems can achieve synchronization by adaptively reducing their speed and/or enhancing the coupling strength. Explicit adaptive algorithms for speed reduction and coupling enhancement are provided. We apply these algorithms to the synchronization of two coupled Lorenz systems. It is found that after a long-time adaptive process, the two coupled chaotic systems can achieve synchronization with almost the minimum required coupling-speed ratio.

Four-pomeron couplings in cut reggeon field theory

International Nuclear Information System (INIS)

Grassberger, P.

1980-01-01

Four-pomeron cutting rules are studied in cut reggeon field theory (CRFT). Without any microscopic model, CRFT allows for three different 4-pomeron couplings. Demanding that CRFT is interpretable as a Markov process, only one of these couplings remains. The cutting rules for the 4-pomeron vertex thus become unique, disagreeing with those found in weak coupling diameter 3 theory. (orig.)

Interlayer exchange coupling, dipolar coupling and magnetoresistance in Fe/MgO/Fe trilayers with a subnanometer MgO barrier

Energy Technology Data Exchange (ETDEWEB)

Kozioł-Rachwał, A. [AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, al. Mickiewicza 30, 30-059 Kraków (Poland); National Institute of Advanced Industrial Science and Technology, Spintronics Research Center, Tsukuba, Ibaraki 305-8568 (Japan); Skowroński, W.; Frankowski, M. [AGH University of Science and Technology, Department of Electronics, al. Mickiewicza 30, 30-059 Kraków (Poland); Chęciński, J. [AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, al. Mickiewicza 30, 30-059 Kraków (Poland); AGH University of Science and Technology, Department of Electronics, al. Mickiewicza 30, 30-059 Kraków (Poland); Ziętek, S.; Rzeszut, P. [AGH University of Science and Technology, Department of Electronics, al. Mickiewicza 30, 30-059 Kraków (Poland); Ślęzak, M.; Matlak, K.; Ślęzak, T. [AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, al. Mickiewicza 30, 30-059 Kraków (Poland); Stobiecki, T. [AGH University of Science and Technology, Department of Electronics, al. Mickiewicza 30, 30-059 Kraków (Poland); Korecki, J. [AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, al. Mickiewicza 30, 30-059 Kraków (Poland); Jerzy Haber Institute of Catalysis and Surface Chemistry, Polish Academy of Sciences, ul. Niezapominajek 8, 30-239 Kraków (Poland)

2017-02-15

Fe/MgO/Fe trilayers with a subnanometer MgO tunnel barrier were grown by molecular beam epitaxy. Longitudinal magnetooptic Kerr effect measurements confirmed the existence of the antiferromagnetic interlayer exchange coupling (IEC) between the Fe layers for 2 Åcoupling was enhanced for the trilayer grown on a homoepitaxial MgO buffer layer, and its IEC constant was estimated to be −3.3 erg/cm{sup 2} at a MgO thickness of 2.7 Å. After magnetic characterization, the sample was patterned into circular-shaped pillars with diameters ranging from 200 nm to 520 nm. We showed that the dipolar coupling that appeared after the nanofabrication process modified the effective coupling between layers, and we determined dependence of the dipolar coupling on the pillar diameter. Finally, magnetoresistance (MR) was measured as a function of MgO thickness (d{sub MgO}), and a non-zero MR was found for the MgO as thin as 3.4 Å. Extrapolation of the MR (d{sub MgO}) dependence to MR=0 allowed us to determine the length of the pinholes in our sample, which was estimated to be (3.2±0.5) Å. - Highlights: • Strong antiferromagnetic (AFM) interlayer exchange coupling (IEC) between Fe layers in Fe/MgO/Fe. • After nanofabrication the effective AFM IEC is enhanced due to the dipolar coupling. • The dipolar coupling that appeared after the nanofabrication process modified the effective coupling between layers. • Non-zero magnetoresistance values registered for the Fe/MgO/Fe trilayers with the MgO spacers as thin as 3.4 Å.

Detection of radiation-induced hydrocarbons in Camembert irradiated before and after the maturing process-comparison of florisil column chromatography and on-line coupled liquid chromatography-gas chromatography

International Nuclear Information System (INIS)

Schulzki, G.; Spiegelberg, A.; Bögl, K.W.; Schreiber, G.A.

1995-01-01

The influence of the maturing process on the detection of radiation-induced volatile hydrocarbons in the fat of Camembert has been investigated. Two analytical methods for separation of the hydrocarbon fraction from the lipid were applied: Florisil column chromatography with subsequent gas chromatographic-mass spectrometric (GC-MS) determination as well as on-line coupled liquid chromatography-GC-MS. The maturing process had no influence on the detection of radiation-induced volatiles. Comparable results were achieved with both analytical methods. However, preference is given to the more effective on-line coupled LC-GC method

Alternative solution algorithm for coupled thermal-hydraulic problems

International Nuclear Information System (INIS)

Farnsworth, D.A.; Rice, J.G.

1986-01-01

A thermal-hydraulic system involves flow of a fluid for which a combined solution of the continuity, momentum, and energy equations is required. When the solutions of the energy and momentum fields are dependent on each other, the system is said to be thermally coupled. A common problem encountered in the numerical solution of strongly coupled thermal-hydraulic problems is a very slow rate of convergence or a complete lack of convergence. Many times this degradation in convergence is due to the lack of true coupling between the energy and momentum fields during the iteration process. In the most widely used solution algorithms - such as the SIMPLE algorithm and its many variants - a sequential solution technique is required. That is, the solution process alternates between the flow and energy fields until a converged solution is obtained. This approach allows only implicit energy-momentum coupling. To improve the convergence rate for strongly coupled problems, a practical solution algorithm that can accommodate true energy-momentum coupling terms was developed. A complete simultaneous (versus sequential) solution of the governing conservation equations utilizing a line-by-line solution was developed and direct coupling terms between the momentum and energy fields were added utilizing a modified Newton-Raphson technique

Twenty years of research at the Mont Terri rock laboratory: what we have learnt

Energy Technology Data Exchange (ETDEWEB)

Bossart, P. [Federal Office of Topography swisstopo, Wabern (Switzerland)

2017-04-15

The 20 papers in this Special Issue address questions related to the safe deep geological disposal of radioactive waste. Here we summarize the main results of these papers related to issues such as: formation of the excavation damaged zone, self-sealing processes, thermo-hydro-mechanical processes, anaerobic corrosion, hydrogen production and effects of microbial activity, and transport and retention processes of radionuclides. In addition, we clarify the question of transferability of results to other sites and programs and the role of rock laboratories for cooperation and training. Finally, we address the important role of the Mont Terri rock laboratory for the public acceptance of radioactive waste disposal. (author)

From individual to collective behaviour of coupled velocity jump processes: A locust example

KAUST Repository

Erban, Radek; Haskovec, Jan

2012-01-01

A class of stochastic individual-based models, written in terms of coupled velocity jump processes, is presented and analysed. This modelling approach incorporates recent experimental findings on the behaviour of locusts. It exhibits nontrivial dynamics with a pitchfork bifurcation and recovers the observed group directional switching. Estimates of the expected switching times, in terms of the number of individuals and values of the model coefi-cients, are obtained using the corresponding Fokker-Planck equation. In the limit of large populations, a system of two kinetic equations (with nonlocal and nonlinear right hand side) is derived and analyzed. The existence of its solutions is proven and the system's long-time behaviour is investigated. Finally, a first step towards the mean field limit of topological interactions is made by studying the efiect of shrinking the interaction radius in the individual-based model. © American Institute of Mathematical Sciences.

From individual to collective behaviour of coupled velocity jump processes: A locust example

KAUST Repository

Erban, Radek

2012-11-01

A class of stochastic individual-based models, written in terms of coupled velocity jump processes, is presented and analysed. This modelling approach incorporates recent experimental findings on the behaviour of locusts. It exhibits nontrivial dynamics with a pitchfork bifurcation and recovers the observed group directional switching. Estimates of the expected switching times, in terms of the number of individuals and values of the model coefi-cients, are obtained using the corresponding Fokker-Planck equation. In the limit of large populations, a system of two kinetic equations (with nonlocal and nonlinear right hand side) is derived and analyzed. The existence of its solutions is proven and the system\\'s long-time behaviour is investigated. Finally, a first step towards the mean field limit of topological interactions is made by studying the efiect of shrinking the interaction radius in the individual-based model. © American Institute of Mathematical Sciences.

Parallel Algorithm Solves Coupled Differential Equations

Science.gov (United States)

Hayashi, A.

1987-01-01

Numerical methods adapted to concurrent processing. Algorithm solves set of coupled partial differential equations by numerical integration. Adapted to run on hypercube computer, algorithm separates problem into smaller problems solved concurrently. Increase in computing speed with concurrent processing over that achievable with conventional sequential processing appreciable, especially for large problems.

Numerical analysis for long-term stability of disposal facility considering thermal and hydraulic effect. Uncoupled analysis for long-term deformation of rock and buffer material and for transport of heat and water

International Nuclear Information System (INIS)

Sawada, Masataka; Okada, Tetsumi; Hasegawa, Takuma

2004-01-01

For the early realization of HLW geological repository and for its rational and economical design and safety assessment, it is important to evaluate the stability of repository facilities in deep underground, where high temperature, earth pressure and underground water flow affect the stability. This report discusses the numerical approaches that are useful for attaining these objectives. One of the efficient approaches is to develop models capable of simulating coupled thermo-hydro-mechanical (T-H-M) processes. Several T-H-M coupled simulation codes have been proposed and the international cooperative research project DECOVALEX has been held from 1991 in order to develop and validate the T-H-M coupled simulations. But mechanical models adopted in these simulation codes are too simple to be applied to the evaluation of long-term interaction of materials that show nonlinear mechanical behavior (especially in the case that surrounding rock is soft sedimentary rock). Before simulating the long-term and coupled phenomena, uncoupled simulations for four phenomena (creep behavior of surrounding rock mass, consolidation and deformation behavior of buffer material, transport of water, and transport of heat) are conducted using various parameters and boundary condition sets. From the results of those simulations, following conclusions are obtained: (1) swelling property of buffer material is important to evaluate mechanical behavior of barrier materials, (2) hydraulic properties of natural barrier can be more important than that of buffer material because suction effect of buffer material is so strong that transport of water in the buffer material is fast, (3) change of thermal properties and filling of gaps caused by water saturation of buffer material have a strong effect on the temperature field. On the next stage, we will develop a T-H-M coupled simulation code to evaluate the mechanical interaction between barrier materials based on the above study. (author)

RELAP5/MOD3 code coupling model

International Nuclear Information System (INIS)

Martin, R.P.; Johnsen, G.W.

1994-01-01

A new capability has been incorporated into RELAP5/MOD3 that enables the coupling of RELAP5/MOD3 to other computer codes. The new capability has been designed to support analysis of the new advanced reactor concepts. Its user features rely solely on new RELAP5 open-quotes styledclose quotes input and the Parallel Virtual Machine (PVM) software, which facilitates process management and distributed communication of multiprocess problems. RELAP5/MOD3 manages the input processing, communication instruction, process synchronization, and its own send and receive data processing. The flexible capability requires that an explicit coupling be established, which updates boundary conditions at discrete time intervals. Two test cases are presented that demonstrate the functionality, applicability, and issues involving use of this capability

Higher-order equation-of-motion coupled-cluster methods for ionization processes.

Science.gov (United States)

Kamiya, Muneaki; Hirata, So

2006-08-21

Compact algebraic equations defining the equation-of-motion coupled-cluster (EOM-CC) methods for ionization potentials (IP-EOM-CC) have been derived and computer implemented by virtue of a symbolic algebra system largely automating these processes. Models with connected cluster excitation operators truncated after double, triple, or quadruple level and with linear ionization operators truncated after two-hole-one-particle (2h1p), three-hole-two-particle (3h2p), or four-hole-three-particle (4h3p) level (abbreviated as IP-EOM-CCSD, CCSDT, and CCSDTQ, respectively) have been realized into parallel algorithms taking advantage of spin, spatial, and permutation symmetries with optimal size dependence of the computational costs. They are based on spin-orbital formalisms and can describe both alpha and beta ionizations from open-shell (doublet, triplet, etc.) reference states into ionized states with various spin magnetic quantum numbers. The application of these methods to Koopmans and satellite ionizations of N2 and CO (with the ambiguity due to finite basis sets eliminated by extrapolation) has shown that IP-EOM-CCSD frequently accounts for orbital relaxation inadequately and displays errors exceeding a couple of eV. However, these errors can be systematically reduced to tenths or even hundredths of an eV by IP-EOM-CCSDT or CCSDTQ. Comparison of spectroscopic parameters of the FH+ and NH+ radicals between IP-EOM-CC and experiments has also underscored the importance of higher-order IP-EOM-CC treatments. For instance, the harmonic frequencies of the A 2Sigma- state of NH+ are predicted to be 1285, 1723, and 1705 cm(-1) by IP-EOM-CCSD, CCSDT, and CCSDTQ, respectively, as compared to the observed value of 1707 cm(-1). The small adiabatic energy separation (observed 0.04 eV) between the X 2Pi and a 4Sigma- states of NH+ also requires IP-EOM-CCSDTQ for a quantitative prediction (0.06 eV) when the a 4Sigma- state has the low-spin magnetic quantum number (s(z) = 1/2). When the

Optical Signatures of Coupled Quantum Dots

Science.gov (United States)

Stinaff, E. A.; Scheibner, M.; Bracker, A. S.; Ponomarev, I. V.; Korenev, V. L.; Ware, M. E.; Doty, M. F.; Reinecke, T. L.; Gammon, D.

2006-02-01

An asymmetric pair of coupled InAs quantum dots is tuned into resonance by applying an electric field so that a single hole forms a coherent molecular wave function. The optical spectrum shows a rich pattern of level anticrossings and crossings that can be understood as a superposition of charge and spin configurations of the two dots. Coulomb interactions shift the molecular resonance of the optically excited state (charged exciton) with respect to the ground state (single charge), enabling light-induced coupling of the quantum dots. This result demonstrates the possibility of optically coupling quantum dots for application in quantum information processing.

Thermoelectrics in Coulomb-coupled quantum dots: Cotunneling and energy-dependent lead couplings

DEFF Research Database (Denmark)

Walldorf, Nicklas; Jauho, Antti-Pekka; Kaasbjerg, Kristen

2017-01-01

We study thermoelectric effects in Coulomb-coupled quantum-dot (CCQD) systems beyond lowest-order tunneling processes and the often applied wide-band approximation. To this end, we present a master-equation (ME) approach based on a perturbative T -matrix calculation of the charge and heat tunneli...

Correlated Coulomb drag in capacitively coupled quantum-dot structures

DEFF Research Database (Denmark)

Kaasbjerg, Kristen; Jauho, Antti-Pekka

2016-01-01

We study theoretically Coulomb drag in capacitively coupled quantum dots (CQDs) -- a biasdriven dot coupled to an unbiased dot where transport is due to Coulomb mediated energy transfer drag. To this end, we introduce a master-equation approach which accounts for higher-order tunneling (cotunneling......) processes as well as energy-dependent lead couplings, and identify a mesoscopic Coulomb drag mechanism driven by nonlocal multi-electron cotunneling processes. Our theory establishes the conditions for a nonzero drag as well as the direction of the drag current in terms of microscopic system parameters...... on Coulomb drag in CQD systems....

Coupling of glycerol processing with Fischer-Tropsch synthesis for production of liquid fuels

DEFF Research Database (Denmark)

Simonetti, D.A.; Rass-Hansen, Jeppe; Kunkes, E.L.

2007-01-01

Liquid alkanes can be produced directly from glycerol by an integrated process involving catalytic conversion to H-2/CO gas mixtures (synthesis gas) combined with Fischer-Tropsch synthesis. Synthesis gas can be produced at high rates and selectivities suitable for Fischer-Tropsch synthesis (H-2/CO...... between 1.0 and 1.6) from concentrated glycerol feed solutions at low temperatures (548 K) and high pressures (1-17 bar) over a 10 wt% Pt-Re/C catalyst with an atomic Pt : Re ratio of 1 : 1. The primary oxygenated hydrocarbon intermediates formed during conversion of glycerol to synthesis gas are ethanol...... in the liquid organic effluent stream and increasing the selectivity to C5+ alkanes by a factor of 2 ( from 0.30 to 0.60). Catalytic conversion of glycerol and Fischer-Tropsch synthesis were coupled in a two-bed reactor system consisting of a Pt-Re/C catalyst bed followed by a Ru/TiO2 catalyst bed...

Real-time control of ion density and ion energy in chlorine inductively coupled plasma etch processing

International Nuclear Information System (INIS)

Chang, C.-H.; Leou, K.-C.; Lin Chaung; Lin, T.-L.; Tseng, C.-W.; Tsai, C.-H.

2003-01-01

In this study, we have experimentally demonstrated the real-time closed-loop control of both ion density and ion energy in a chlorine inductively coupled plasma etcher. To measure positive ion density, the trace rare gases-optical emission spectroscopy is used to measure the chlorine positive ion density. An rf voltage probe is adopted to measure the root-mean-square rf voltage on the electrostatic chuck which is linearly dependent on sheath voltage. One actuator is a 13.56 MHz rf generator to drive the inductive coil seated on a ceramic window. The second actuator is also a 13.56 MHz rf generator to power the electrostatic chuck. The closed-loop controller is designed to compensate for process drift, process disturbance, and pilot wafer effect and to minimize steady-state error of plasma parameters. This controller has been used to control the etch process of unpatterned polysilicon. The experimental results showed that the closed-loop control had a better repeatability of plasma parameters compared with open-loop control. The closed-loop control can eliminate the process disturbance resulting from reflected power. In addition, experimental results also demonstrated that closed-loop control has a better reproducibility in etch rate as compared with open-loop control

Process monitored spectrophotometric titration coupled with chemometrics for simultaneous determination of mixtures of weak acids.

Science.gov (United States)

Liao, Lifu; Yang, Jing; Yuan, Jintao

2007-05-15

A new spectrophotometric titration method coupled with chemometrics for the simultaneous determination of mixtures of weak acids has been developed. In this method, the titrant is a mixture of sodium hydroxide and an acid-base indicator, and the indicator is used to monitor the titration process. In a process of titration, both the added volume of titrant and the solution acidity at each titration point can be obtained simultaneously from an absorption spectrum by least square algorithm, and then the concentration of each component in the mixture can be obtained from the titration curves by principal component regression. The method only needs the information of absorbance spectra to obtain the analytical results, and is free of volumetric measurements. The analyses are independent of titration end point and do not need the accurate values of dissociation constants of the indicator and the acids. The method has been applied to the simultaneous determination of the mixtures of benzoic acid and salicylic acid, and the mixtures of phenol, o-chlorophenol and p-chlorophenol with satisfactory results.

Investigation of Coupled Processes and Impact of High Temperature Limits in Argillite Rock: FY17 Progress. Predecisional Draft

Energy Technology Data Exchange (ETDEWEB)

Zheng, Liange; Rutqvist, Jonny; Xu, Hao; Kim, Kunwhi; Voltolini, Marco; Cao, Xiaoyuan

2017-07-03

The focus of research within the Spent Fuel and Waste Science and Technology (SFWST) (formerly called Used Fuel Disposal) Campaign is on repository-induced interactions that may affect the key safety characteristics of EBS bentonite and an argillaceous rock. These include thermal-hydrologicalmechanical- chemical (THMC) process interactions that occur as a result of repository construction and waste emplacement. Some of the key questions addressed in this report include the development of fracturing in the excavation damaged zone (EDZ) and THMC effects on the near-field argillaceous rock and buffer materials and petrophysical characteristics, particularly the impacts of temperature rise caused by waste heat. This report documents the following research activities. Section 2 presents THM model developments and validation, including modeling of underground heater experiments at Mont Terri and Bure underground research laboratories (URLs). The heater experiments modeled are the Mont Terri FE (Full-scale Emplacement) Experiment, conducted as part of the Mont Terri Project, and the TED in heater test conducted in Callovo-Oxfordian claystone (COx) at the Meuse/Haute-Marne (MHM) underground research laboratory in France. The modeling of the TED heater test is one of the Tasks of the DEvelopment of COupled Models and their VAlidation against EXperiments (DECOVALEX)-2019 project. Section 3 presents the development and application of thermal-hydrological-mechanical-chemical (THMC) modeling to evaluate EBS bentonite and argillite rock responses under different temperatures (100 °C and 200 °C). Model results are presented to help to understand the impact of high temperatures on the properties and behavior of bentonite and argillite rock. Eventually the process model will support a robust GDSA model for repository performance assessments. Section 4 presents coupled THMC modeling for an in situ test conducted at Grimsel underground laboratory in Switzerland in the Full

Couple-level Minority Stress: An Examination of Same-sex Couples' Unique Experiences.

Science.gov (United States)

Frost, David M; LeBlanc, Allen J; de Vries, Brian; Alston-Stepnitz, Eli; Stephenson, Rob; Woodyatt, Cory

2017-12-01

Social stress resulting from stigma, prejudice, and discrimination-"minority stress"-negatively impacts sexual minority individuals' health and relational well-being. The present study examined how being in a same-sex couple can result in exposure to unique minority stressors not accounted for at the individual level. Relationship timeline interviews were conducted with 120 same-sex couples equally distributed across two study sites (Atlanta and San Francisco), gender (male and female), and relationship duration (at least six months but less than three years, at least three years but less than seven years, and seven or more years). Directed content analyses identified 17 unique couple-level minority stressors experienced within nine distinct social contexts. Analyses also revealed experiences of dyadic minority stress processes (stress discrepancies and stress contagion). These findings can be useful in future efforts to better understand and address the cumulative impact of minority stress on relational well-being and individual health.

Molecular-state close-coupling theory including continuum states. I. Derivation of close-coupled equations

International Nuclear Information System (INIS)

Thorson, W.R.; Bandarage, G.

1988-01-01

We formulate a close-coupling theory of slow ion-atom collisions based on molecular (adiabatic) electronic states, and including the electronic continuum. The continuum is represented by packet states spanning it locally and constructed explicitly from exact continuum states. Particular attention is given to two fundamental questions: (1) Unbound electrons can escape from the local region spanned by the packet states. We derive close-coupled integral equations correctly including the escape effects; the ''propagator'' generated by these integral equations does not conserve probability within the close-coupled basis. Previous molecular-state formulations including the continuum give no account of escape effects. (2) Nonadiabatic couplings of adiabatic continuum states with the same energy are singular, reflecting the fact that an adiabatic description of continuum behavior is not valid outside a local region. We treat these singularities explicitly and show that an accurate representation of nonadiabatic couplings within the local region spanned by a set of packet states is well behaved. Hence an adiabatic basis-set description can be used to describe close coupling to the continuum in a local ''interaction region,'' provided the effects of escape are included. In principle, the formulation developed here can be extended to a large class of model problems involving many-electron systems and including models for Penning ionization and collisional detachment processes

Multi-disciplinary coupling for integrated design of propulsion systems

Science.gov (United States)

Chamis, C. C.; Singhal, S. N.

1993-01-01

Effective computational simulation procedures are described for modeling the inherent multi-disciplinary interactions for determining the true response of propulsion systems. Results are presented for propulsion system responses including multi-discipline coupling effects via (1) coupled multi-discipline tailoring, (2) an integrated system of multidisciplinary simulators, (3) coupled material-behavior/fabrication-process tailoring, (4) sensitivities using a probabilistic simulator, and (5) coupled materials/structures/fracture/probabilistic behavior simulator. The results show that the best designs can be determined if the analysis/tailoring methods account for the multi-disciplinary coupling effects. The coupling across disciplines can be used to develop an integrated interactive multi-discipline numerical propulsion system simulator.

On the possibility of the multiple inductively coupled plasma and helicon plasma sources for large-area processes

Energy Technology Data Exchange (ETDEWEB)

Lee, Jin-Won; Lee, Yun-Seong, E-mail: leeeeys@kaist.ac.kr; Chang, Hong-Young [Low-temperature Plasma Laboratory, Department of Physics, Korea Advanced Institute of Science and Technology, Daejeon 305-701 (Korea, Republic of); An, Sang-Hyuk [Agency of Defense Development, Yuseong-gu, Daejeon 305-151 (Korea, Republic of)

2014-08-15

In this study, we attempted to determine the possibility of multiple inductively coupled plasma (ICP) and helicon plasma sources for large-area processes. Experiments were performed with the one and two coils to measure plasma and electrical parameters, and a circuit simulation was performed to measure the current at each coil in the 2-coil experiment. Based on the result, we could determine the possibility of multiple ICP sources due to a direct change of impedance due to current and saturation of impedance due to the skin-depth effect. However, a helicon plasma source is difficult to adapt to the multiple sources due to the consistent change of real impedance due to mode transition and the low uniformity of the B-field confinement. As a result, it is expected that ICP can be adapted to multiple sources for large-area processes.

Equilibration and hydrodynamics at strong and weak coupling

NARCIS (Netherlands)

Schee, Wilke van der

2017-01-01

We give an updated overview of both weak and strong coupling methods to describe the approach to a plasma described by viscous hydrodynamics, a process now called hydrodynamisation. At weak coupling the very first moments after a heavy ion collision is described by the colour-glass condensate

Soil remediation using a coupled process: soil washing with surfactant followed by photo-Fenton oxidation

International Nuclear Information System (INIS)

Villa, Ricardo D.; Trovo, Alam G.; Nogueira, Raquel F. Pupo

2010-01-01

In the present work the use of a coupled process, soil washing and photo-Fenton oxidation, was investigated for remediation of a soil contaminated with p,p'-DDT (DDT) and p,p'-DDE (DDE), and a soil artificially contaminated with diesel. In the soil washing experiments, Triton X-100 (TX-100) aqueous solutions were used at different concentrations to obtain wastewaters with different compositions. Removal efficiencies of 66% (DDT), 80% (DDE) and 100% (diesel) were achieved for three sequential washings using a TX-100 solution strength equivalent to 12 times the effective critical micelle concentration of the surfactant (12 CMC eff ). The wastewater obtained was then treated using a solar photo-Fenton process. After 6 h irradiation, 99, 95 and 100% degradation efficiencies were achieved for DDT, DDE and diesel, respectively. In all experiments, the concentration of dissolved organic carbon decreased by at least 95%, indicating that residual concentration of contaminants and/or TX-100 in the wastewater was very low. The co-extraction of metals was also evaluated. Among the metals analyzed (Pb, Cr, Ni, Cu, Cd, Mn and Co), only Cr and Mn were detected in the wastewater at concentrations above the maximum value permitted by current Brazilian legislation. The effective removal of contaminants from soil by the TX-100 washing process, together with the high degradation efficiency of the solar photo-Fenton process, suggests that this procedure could be a useful option for soil remediation.

Soil remediation using a coupled process: soil washing with surfactant followed by photo-Fenton oxidation

Energy Technology Data Exchange (ETDEWEB)

Villa, Ricardo D., E-mail: ricardovilla@ufmt.br [UNESP - Sao Paulo State University, Institute of Chemistry of Araraquara, Department of Analytical Chemistry, P.O. Box 355, 14801-970 Araraquara, SP (Brazil); Trovo, Alam G., E-mail: alamtrovo@smail.ufsm.br [UNESP - Sao Paulo State University, Institute of Chemistry of Araraquara, Department of Analytical Chemistry, P.O. Box 355, 14801-970 Araraquara, SP (Brazil); Nogueira, Raquel F. Pupo, E-mail: nogueira@iq.unesp.br [UNESP - Sao Paulo State University, Institute of Chemistry of Araraquara, Department of Analytical Chemistry, P.O. Box 355, 14801-970 Araraquara, SP (Brazil)

2010-02-15

In the present work the use of a coupled process, soil washing and photo-Fenton oxidation, was investigated for remediation of a soil contaminated with p,p'-DDT (DDT) and p,p'-DDE (DDE), and a soil artificially contaminated with diesel. In the soil washing experiments, Triton X-100 (TX-100) aqueous solutions were used at different concentrations to obtain wastewaters with different compositions. Removal efficiencies of 66% (DDT), 80% (DDE) and 100% (diesel) were achieved for three sequential washings using a TX-100 solution strength equivalent to 12 times the effective critical micelle concentration of the surfactant (12 CMC{sub eff}). The wastewater obtained was then treated using a solar photo-Fenton process. After 6 h irradiation, 99, 95 and 100% degradation efficiencies were achieved for DDT, DDE and diesel, respectively. In all experiments, the concentration of dissolved organic carbon decreased by at least 95%, indicating that residual concentration of contaminants and/or TX-100 in the wastewater was very low. The co-extraction of metals was also evaluated. Among the metals analyzed (Pb, Cr, Ni, Cu, Cd, Mn and Co), only Cr and Mn were detected in the wastewater at concentrations above the maximum value permitted by current Brazilian legislation. The effective removal of contaminants from soil by the TX-100 washing process, together with the high degradation efficiency of the solar photo-Fenton process, suggests that this procedure could be a useful option for soil remediation.

Remotely operated replaceable process equipment

International Nuclear Information System (INIS)

Westendorf, H.

1987-01-01

The coupling process of pneumatic and electrical auxiliary lines of a pneumatic control pressure line in a large cell of the reprocessing plant is carried out, together with the coupling process of the connecting flange of the process equipment. The coupling places of the auxiliary lines, such as control or supply lines, are laid in the flange parts of the flanges to be connected. The pipe flange on the frame side remains flush with the connecting flange of the process equipment. (DG) [de

Welding process decoupling for improved control

International Nuclear Information System (INIS)

Hardt, D.E.; Eagar, T.W.; Lang, J.H.; Jones, L.

1993-01-01

The Gas Metal Arc Welding Process is characterized by many important process outputs, all of which should be controlled to ensure consistent high performance joints. However, application of multivariable control methods is confounded by the strong physical coupling of typical outputs of bead shape and thermal properties. This coupling arises from the three dimensional thermal diffusion processes inherent in welding, and cannot be overcome without significant process modification. This paper presents data on the extent of coupling of the process, and proposes process changes to overcome such strong output coupling. Work in rapid torch vibration to change the heat input distribution is detailed, and methods for changing the heat balance between base and fill material heat are described

TOUGH2Biot - A simulator for coupled thermal-hydrodynamic-mechanical processes in subsurface flow systems: Application to CO2 geological storage and geothermal development

Science.gov (United States)

Lei, Hongwu; Xu, Tianfu; Jin, Guangrong

2015-04-01

Coupled thermal-hydrodynamic-mechanical processes have become increasingly important in studying the issues affecting subsurface flow systems, such as CO2 sequestration in deep saline aquifers and geothermal development. In this study, a mechanical module based on the extended Biot consolidation model was developed and incorporated into the well-established thermal-hydrodynamic simulator TOUGH2, resulting in an integrated numerical THM simulation program TOUGH2Biot. A finite element method was employed to discretize space for rock mechanical calculation and the Mohr-Coulomb failure criterion was used to determine if the rock undergoes shear-slip failure. Mechanics is partly coupled with the thermal-hydrodynamic processes and gives feedback to flow through stress-dependent porosity and permeability. TOUGH2Biot was verified against analytical solutions for the 1D Terzaghi consolidation and cooling-induced subsidence. TOUGH2Biot was applied to evaluate the thermal, hydrodynamic, and mechanical responses of CO2 geological sequestration at the Ordos CCS Demonstration Project, China and geothermal exploitation at the Geysers geothermal field, California. The results demonstrate that TOUGH2Biot is capable of analyzing change in pressure and temperature, displacement, stress, and potential shear-slip failure caused by large scale underground man-made activity in subsurface flow systems. TOUGH2Biot can also be easily extended for complex coupled process problems in fractured media and be conveniently updated to parallel versions on different platforms to take advantage of high-performance computing.

Effect of Group Cognitive Behavioral Couples Therapy on Couple Burnout and Divorce Tendency in Couples

Directory of Open Access Journals (Sweden)

M Mohammadi

2017-02-01

Full Text Available Background & aim: Couple burnout is one of the phenomena which involve many couples, it is among the main causes of emotional divorce, and without proper management and treatment, and it can lay the ground for formal divorce among couples. Cognitive behavioral couple therapy is one of the existing approaches in the couple therapy field, the efficiency of which has been established for resolving many marital problems. The present study was designed by the aim of investigating the effect of group cognitive behavioral couple therapy on couple burnout and divorce tendency in couples.   Methods: The present research was of applied research type. The research method was semi-empirical with a pretest-posttest with control group design. The research population included all the couples with marital conflict and problems who, after a recall announcement of the researcher, visited the counseling and psychological services center located in Gorgan city in 2014. By using the available sampling method, 20 couples were selected among the volunteer and qualified couples for the research, and they were assigned into experiment and control groups (10 couples per group by random assignment. In the present research, the Pines burnout questionnaire (1996 and divorce tendency scale of Rouswelt, Johnson, and Mouro (1986 were used for gathering the data. After taking the pretest, the group cognitive behavioral couple therapy based on the couple therapy model of Baucom  and colleagues (2008 was held in 10 2-hour weekly sessions for the experiment group couples, while the control group couples received no intervention. The data were analyzed through descriptive statistics method and multivariate covariance analysis (MANCOVA in SPSS v.20. Results: The multivariate covariance analysis results for couple burnout (F= 28.80 and divorce tendency (F= 51.25 suggested that there was a significant difference between the couples of experiment and control groups (P< 0

Synchronization and chaotic dynamics of coupled mechanical metronomes

Science.gov (United States)

Ulrichs, Henning; Mann, Andreas; Parlitz, Ulrich

2009-12-01

Synchronization scenarios of coupled mechanical metronomes are studied by means of numerical simulations showing the onset of synchronization for two, three, and 100 globally coupled metronomes in terms of Arnol'd tongues in parameter space and a Kuramoto transition as a function of coupling strength. Furthermore, we study the dynamics of metronomes where overturning is possible. In this case hyperchaotic dynamics associated with some diffusion process in configuration space is observed, indicating the potential complexity of metronome dynamics.

Multi-disciplinary coupling effects for integrated design of propulsion systems

Science.gov (United States)

Chamis, C. C.; Singhal, S. N.

1993-01-01

Effective computational simulation procedures are described for modeling the inherent multi-disciplinary interactions which govern the accurate response of propulsion systems. Results are presented for propulsion system responses including multi-disciplinary coupling effects using coupled multi-discipline thermal, structural, and acoustic tailoring; an integrated system of multi-disciplinary simulators; coupled material behavior/fabrication process tailoring; sensitivities using a probabilistic simulator; and coupled materials, structures, fracture, and probabilistic behavior simulator. The results demonstrate that superior designs can be achieved if the analysis/tailoring methods account for the multi-disciplinary coupling effects. The coupling across disciplines can be used to develop an integrated coupled multi-discipline numerical propulsion system simulator.

Surrogate versus couple therapy in vaginismus.

Science.gov (United States)

Ben-Zion, Itzhak; Rothschild, Shelly; Chudakov, Bella; Aloni, Ronit

2007-05-01

Women who do not have a cooperative partner cannot complete the usual therapeutic process in the treatment of vaginismus, because they cannot progress to the stage of practicing the insertion of the man partner's fingers and the insertion of a penis. To compare traditional couple therapy with therapy utilizing a surrogate partner. The study was controlled and retrospective. Data were obtained from the treatment charts of patients who had come to the clinic for treatment of vaginismus. Sixteen vaginismus patients who were treated with a man surrogate partner were compared with 16 vaginismus patients who were treated with their own partners. Successful pain-free intercourse upon completion of therapy. One hundred percent of the surrogate patients succeeded in penile-vaginal intercourse compared with 75% in the couples group (P = 0.1). All surrogate patients ended the therapy because it was fully successful, compared with 69% in the couples group. Twelve percent of the couples group ended the therapy because it failed, and 19% because the couples decided to separate. Treating vaginismus with a man surrogate partner was at least as effective as couple therapy. Surrogate therapy may be considered for vaginismus patients who have no cooperative partner.

Multimode Coupling Theory for Kelvin–Helmholtz Instability in Incompressible Fluid

International Nuclear Information System (INIS)

Li-Feng, Wang; Ying-Jun, Li; Wen-Hua, Ye; Zheng-Feng, Fan

2009-01-01

A weakly nonlinear model is proposed for multimode Kelvin–Helmholtz instability. The second-order mode coupling formula for Kelvin–Helmholtz instability in two-dimensional incompressible fluid is presented by expanding the perturbation velocity potential to second order. It is found that there is an important resonance in the course of the sum frequency mode coupling but the difference frequency mode coupling does not have. This resonance makes the sum frequency mode coupling process relatively complex. The sum frequency mode coupling is strongly dependent on time especially when the density of the two fluids is adjacent and the difference frequency mode coupling is not

Desynchronization in coupled systems with quasiperiodic driving

DEFF Research Database (Denmark)

Vadivasova; Sosnovtseva, Olga; Balanov

2000-01-01

We describe the development of coexisting attractors in coupled quasiperiodically forced maps. The process of loss of complete synchronization in the systems, which individually demonstrates strange nonchaotic behavior, is studied. With this process, the complex structure of the basin of attraction...

Contribution to the optimization of the coupling of nuclear reactors to desalination processes; Contribution a l'optimisation du couplage des reacteurs nucleaires aux procedes de dessalement

Energy Technology Data Exchange (ETDEWEB)

Dardour, S

2007-04-15

This work deals with modelling, simulation and optimization of the coupling between nuclear reactors (PWR, modular high temperature reactors) and desalination processes (multiple effect distillation, reverse osmosis). The reactors considered in this study are PWR (Pressurized Water Reactor) and GTMHR (Gas Turbine Modular Helium Reactor). The desalination processes retained are MED (Multi Effect Distillation) and SWRO (Sea Water Reverse Osmosis). A software tool: EXCELEES of thermodynamic modelling of coupled systems, based on the Engineering Algebraic Equation Solver has been developed. Models of energy conversion systems and of membrane desalination processes and distillation have been developed. Based on the first and second principles of thermodynamics, these models have allowed to determine the optimal running point of the coupled systems. The thermodynamic analysis has been completed by a first economic evaluation. Based on the use of the DEEP software of the IAEA, this evaluation has confirmed the interest to use these types of reactors for desalination. A modelling tool of thermal processes of desalination in dynamic condition has been developed too. This tool has been applied to the study of the dynamics of an existing plant and has given satisfying results. A first safety checking has been at last carried out. The transients able to jeopardize the integrated system have been identified. Several measures aiming at consolidate the safety have been proposed. (O.M.)

Nonlinear control of a multicomponent distillation process coupled with a binary distillation model as an EKF predictor.

Science.gov (United States)

Jana, Amiya Kumar; Ganguly, Saibal; Samanta, Amar Nath

2006-10-01

The work is devoted to design the globally linearizing control (GLC) strategy for a multicomponent distillation process. The control system is comprised with a nonlinear transformer, a nonlinear closed-loop state estimator [extended Kalman filter (EKF)], and a linear external controller [conventional proportional integral (PI) controller]. The model of a binary distillation column has been used as a state predictor to avoid huge design complexity of the EKF estimator. The binary components are the light key and the heavy key of the multicomponent system. The proposed GLC-EKF (GLC in conjunction with EKF) control algorithm has been compared with the GLC-ROOLE [GLC coupled with reduced-order open-loop estimator (ROOLE)] and the dual-loop PI controller based on set point tracking and disturbance rejection performance. Despite huge process/predictor mismatch, the superiority of the GLC-EKF has been inspected over the GLC-ROOLE control structure.

Processing device with self-scrubbing logic

Science.gov (United States)

Wojahn, Christopher K.

2016-03-01

An apparatus includes a processing unit including a configuration memory and self-scrubber logic coupled to read the configuration memory to detect compromised data stored in the configuration memory. The apparatus also includes a watchdog unit external to the processing unit and coupled to the self-scrubber logic to detect a failure in the self-scrubber logic. The watchdog unit is coupled to the processing unit to selectively reset the processing unit in response to detecting the failure in the self-scrubber logic. The apparatus also includes an external memory external to the processing unit and coupled to send configuration data to the configuration memory in response to a data feed signal outputted by the self-scrubber logic.

THE ROLE OF PROTOTYPING AND SIMULATION IN THE DEVELOPMENT PROCESS OF AN ELASTIC COUPLING WITH FLEXIBLE MEMBRANES

Directory of Open Access Journals (Sweden)

DOBRE Daniel

2015-06-01

Full Text Available In the conditions of a competitive market, the use of 3D modelling, visualisation and simulation tools enable the entire coupling to be designed and developed in the pre-manufacturing phase. Several advantages of introducing virtual prototyping are offered. The goal for the coupling prototype is to answer questions about performance and reliability in order to identify necessary engineering changes for the final coupling variant. Facilitating the virtual reality communication capability, different variations of the geometry and other characteristics can be studied and discussed in a more efficient mode. Virtual features of the coupling structure are described and analysed for the efficient realization of coupling project. At the end, the paper presents design simulations to prove the behaviour and functionality of the coupling for different operational scenarios: mechanical stress, buckling stability and modal analysis.

Fluid lipid bilayers: Intermonolayer coupling and its thermodynamic manifestations

DEFF Research Database (Denmark)

Hansen, Per Lyngs; Miao, Ling; Ipsen, John Hjorth

1998-01-01

of a phenomenological model that describes the necessary types of degrees of freedom and their interplay, which reflects different modes of intermonolayer coupling. Furthermore, we investigate! based on the phenomenological model, the manifestations of the intermonolayer coupling both in the lateral ordering processes...

Numerical modelling of levee stability based on coupled mechanical, thermal and hydrogeological processes

Directory of Open Access Journals (Sweden)

Dwornik Maciej

2016-01-01

Full Text Available The numerical modelling of coupled mechanical, thermal and hydrogeological processes for a soil levee is presented in the paper. The modelling was performed for a real levee that was built in Poland as a part of the ISMOP project. Only four parameters were changed to build different flood waves: the water level, period of water increase, period of water decrease, and period of low water level after the experiment. Results of numerical modelling shows that it is possible and advisable to calculate simultaneously changes of thermal and hydro-mechanical fields. The presented results show that it is also possible to use thermal sensors in place of more expensive pore pressure sensors, with some limitations. The results of stability analysis show that the levee is less stable when the water level decreases, after which factor of safety decreases significantly. For all flooding wave parameters described in the paper, the levee is very stable and factor of safety variations for any particular stage were not very large.

Correlated Coulomb Drag in Capacitively Coupled Quantum-Dot Structures.

Science.gov (United States)

Kaasbjerg, Kristen; Jauho, Antti-Pekka

2016-05-13

We study theoretically Coulomb drag in capacitively coupled quantum dots (CQDs)-a bias-driven dot coupled to an unbiased dot where transport is due to Coulomb mediated energy transfer drag. To this end, we introduce a master-equation approach that accounts for higher-order tunneling (cotunneling) processes as well as energy-dependent lead couplings, and identify a mesoscopic Coulomb drag mechanism driven by nonlocal multielectron cotunneling processes. Our theory establishes the conditions for a nonzero drag as well as the direction of the drag current in terms of microscopic system parameters. Interestingly, the direction of the drag current is not determined by the drive current, but by an interplay between the energy-dependent lead couplings. Studying the drag mechanism in a graphene-based CQD heterostructure, we show that the predictions of our theory are consistent with recent experiments on Coulomb drag in CQD systems.

Chemical event chain model of coupled genetic oscillators.

Science.gov (United States)

Jörg, David J; Morelli, Luis G; Jülicher, Frank

2018-03-01

We introduce a stochastic model of coupled genetic oscillators in which chains of chemical events involved in gene regulation and expression are represented as sequences of Poisson processes. We characterize steady states by their frequency, their quality factor, and their synchrony by the oscillator cross correlation. The steady state is determined by coupling and exhibits stochastic transitions between different modes. The interplay of stochasticity and nonlinearity leads to isolated regions in parameter space in which the coupled system works best as a biological pacemaker. Key features of the stochastic oscillations can be captured by an effective model for phase oscillators that are coupled by signals with distributed delays.

Chemical event chain model of coupled genetic oscillators

Science.gov (United States)

Jörg, David J.; Morelli, Luis G.; Jülicher, Frank

2018-03-01

We introduce a stochastic model of coupled genetic oscillators in which chains of chemical events involved in gene regulation and expression are represented as sequences of Poisson processes. We characterize steady states by their frequency, their quality factor, and their synchrony by the oscillator cross correlation. The steady state is determined by coupling and exhibits stochastic transitions between different modes. The interplay of stochasticity and nonlinearity leads to isolated regions in parameter space in which the coupled system works best as a biological pacemaker. Key features of the stochastic oscillations can be captured by an effective model for phase oscillators that are coupled by signals with distributed delays.

Nonlinear spin wave coupling in adjacent magnonic crystals

Energy Technology Data Exchange (ETDEWEB)

Sadovnikov, A. V., E-mail: sadovnikovav@gmail.com; Nikitov, S. A. [Laboratory “Metamaterials,” Saratov State University, Saratov 410012 (Russian Federation); Kotel' nikov Institute of Radioengineering and Electronics, Russian Academy of Sciences, Moscow 125009 (Russian Federation); Beginin, E. N.; Morozova, M. A.; Sharaevskii, Yu. P.; Grishin, S. V.; Sheshukova, S. E. [Laboratory “Metamaterials,” Saratov State University, Saratov 410012 (Russian Federation)

2016-07-25

We have experimentally studied the coupling of spin waves in the adjacent magnonic crystals. Space- and time-resolved Brillouin light-scattering spectroscopy is used to demonstrate the frequency and intensity dependent spin-wave energy exchange between the side-coupled magnonic crystals. The experiments and the numerical simulation of spin wave propagation in the coupled periodic structures show that the nonlinear phase shift of spin wave in the adjacent magnonic crystals leads to the nonlinear switching regime at the frequencies near the forbidden magnonic gap. The proposed side-coupled magnonic crystals represent a significant advance towards the all-magnonic signal processing in the integrated magnonic circuits.

Nonlinear spin wave coupling in adjacent magnonic crystals

International Nuclear Information System (INIS)

Sadovnikov, A. V.; Nikitov, S. A.; Beginin, E. N.; Morozova, M. A.; Sharaevskii, Yu. P.; Grishin, S. V.; Sheshukova, S. E.

2016-01-01

We have experimentally studied the coupling of spin waves in the adjacent magnonic crystals. Space- and time-resolved Brillouin light-scattering spectroscopy is used to demonstrate the frequency and intensity dependent spin-wave energy exchange between the side-coupled magnonic crystals. The experiments and the numerical simulation of spin wave propagation in the coupled periodic structures show that the nonlinear phase shift of spin wave in the adjacent magnonic crystals leads to the nonlinear switching regime at the frequencies near the forbidden magnonic gap. The proposed side-coupled magnonic crystals represent a significant advance towards the all-magnonic signal processing in the integrated magnonic circuits.

Path coupling and aggregate path coupling

CERN Document Server

Kovchegov, Yevgeniy

2018-01-01

This book describes and characterizes an extension to the classical path coupling method applied to statistical mechanical models, referred to as aggregate path coupling. In conjunction with large deviations estimates, the aggregate path coupling method is used to prove rapid mixing of Glauber dynamics for a large class of statistical mechanical models, including models that exhibit discontinuous phase transitions which have traditionally been more difficult to analyze rigorously. The book shows how the parameter regions for rapid mixing for several classes of statistical mechanical models are derived using the aggregate path coupling method.

Coupled interactions between volatile activity and Fe oxidation state during arc crustal processes

Science.gov (United States)

Humphreys, Madeleine C.S.; Brooker, R; Fraser, D.C.; Burgisser, A; Mangan, Margaret T.; McCammon, C

2015-01-01

Arc magmas erupted at the Earth’s surface are commonly more oxidized than those produced at mid-ocean ridges. Possible explanations for this high oxidation state are that the transfer of fluids during the subduction process results in direct oxidation of the sub-arc mantle wedge, or that oxidation is caused by the effect of later crustal processes, including protracted fractionation and degassing of volatile-rich magmas. This study sets out to investigate the effect of disequilibrium crustal processes that may involve coupled changes in H2O content and Fe oxidation state, by examining the degassing and hydration of sulphur-free rhyolites. We show that experimentally hydrated melts record strong increases in Fe3+/∑Fe with increasing H2O concentration as a result of changes in water activity. This is relevant for the passage of H2O-undersaturated melts from the deep crust towards shallow crustal storage regions, and raises the possibility that vertical variations in fO2 might develop within arc crust. Conversely, degassing experiments produce an increase in Fe3+/∑Fe with decreasing H2O concentration. In this case the oxidation is explained by loss of H2 as well as H2O into bubbles during decompression, consistent with thermodynamic modelling, and is relevant for magmas undergoing shallow degassing en route to the surface. We discuss these results in the context of the possible controls on fO2 during the generation, storage and ascent of magmas in arc settings, in particular considering the timescales of equilibration relative to observation as this affects the quality of the petrological record of magmatic fO2.

Strange attractors and synchronization dynamics of coupled Van der Pol-Duffing oscillators

International Nuclear Information System (INIS)

Yamapi, R.; Filatrella, G.

2006-07-01

We consider in this paper the dynamics and synchronization of coupled chaotic Van der Pol-Duffing systems. The stability of the synchronization process between two coupled autonomous Van der Pol model is first analyzed analytically and numerically, before following the problem of synchronizing chaos both on the same and different chaotic orbits of two coupled Van der Pol-Duffing systems. The stability boundaries of the synchronization process are derived and the effects of the amplitude of the periodic perturbation of the coupling parameter on these boundaries are analyzed. The results are provided on the stability map in the (q, K) plane. (author)

Coupled DM Heating in SCDEW Cosmologies

Directory of Open Access Journals (Sweden)

Silvio Bonometto

2017-08-01

Full Text Available Strongly-Coupled Dark Energy plus Warm dark matter (SCDEW cosmologies admit the stationary presence of ∼1% of coupled-DM and DE, since inflationary reheating. Coupled-DM fluctuations therefore grow up to non-linearity even in the early radiative expansion. Such early non-linear stages are modelized here through the evolution of a top-hat density enhancement, reaching an early virial balance when the coupled-DM density contrast is just 25–26, and the DM density enhancement is ∼10 % of the total density. During the time needed to settle in virial equilibrium, the virial balance conditions, however, continue to modify, so that “virialized” lumps undergo a complete evaporation. Here, we outline that DM particles processed by overdensities preserve a fraction of their virial momentum. Although fully non-relativistic, the resulting velocities (moderately affect the fluctuation dynamics over greater scales, entering the horizon later on.

Final Report DE-SC0006997; PI Sharp; Coupled Biological and Micro-XAS/XRF Analysis of In Situ Uranium Biogeochemical Processes

Energy Technology Data Exchange (ETDEWEB)

Sharp, Jonathan O. [Colorado School of Mines, Golden, CO (United States)

2016-03-30

Project Overview: The impact of the original seed award was substantially increased by leveraging a postdoctoral fellowship (Marie Curie Postdoctoral Fellowship) and parallel funds from (A) synergistic project supported by NSF and (B) with DOE collaborators (PI’s Ranville and Williams) as well as no-cost extension that greatly increased the impact and publications associated with the project. In aligning with SBR priorities, the project’s focus was extended more broadly to explore coupled biogeochemical analysis of metal (im)mobilization processes beyond uranium with a foundation in integrating microbial ecology with geochemical analyses. This included investigations of arsenic and zinc during sulfate reducing conditions in addition to direct microbial reduction of metals. Complimentary work with NSF funding and collaborative DOE interactions further increased the project scope to investigate metal (im)mobilization coupled to biogeochemical perturbations in forest ecosystems with an emphasis on coupled carbon and metal biogeochemistry. In total, the project was highly impactful and resulted in 9 publications and directly supported salary/tuition for 3 graduate students at various stages of their academic careers as well as my promotion to Associate Professor. In going forward, findings provided inspiration for a two subsequent proposals with collaborators at Lawrence Berkeley Laboratory and others that are currently in review (as of March 2016).

Digital Dwelling: Technology in Couple and Family Relationships

Science.gov (United States)

Hertlein, Katherine M.

2012-01-01

We are in an unprecedented age of technology. Few articles in family journals address online behavior, intimacy patterns, and influences on the ways couples and families communicate through technology. The purpose of this article is to use a multitheoretical model to describe the process of how technologies are affecting couple and family life.…

Effect of interactions for one-dimensional asymmetric exclusion processes under periodic and bath-adapted coupling environment

Science.gov (United States)

Midha, Tripti; Kolomeisky, Anatoly B.; Gupta, Arvind Kumar

2018-04-01

Stimulated by the effect of the nearest neighbor interactions in vehicular traffic and motor proteins, we study a 1D driven lattice gas model, in which the nearest neighbor particle interactions are taken in accordance with the thermodynamic concepts. The non-equilibrium steady-state properties of the system are analyzed under both open and periodic boundary conditions using a combination of cluster mean-field analysis and Monte Carlo simulations. Interestingly, the fundamental diagram of current versus density shows a complex behavior with a unimodal dependence for attractions and weak repulsions that turns into the bimodal behavior for stronger repulsive interactions. Specific details of system-reservoir coupling for the open system have a strong effect on the stationary phases. We produce the steady-state phase diagrams for the bulk-adapted coupling to the reservoir using the minimum and maximum current principles. The strength and nature of interaction energy has a striking influence on the number of stationary phases. We observe that interactions lead to correlations having a strong impact on the system dynamical properties. The correlation between any two sites decays exponentially as the distance between the sites increases. Moreover, they are found to be short-range for repulsions and long-range for attractions. Our results also suggest that repulsions and attractions asymmetrically modify the dynamics of interacting particles in exclusion processes.

Gestural Coupling and Social Cognition: Möbius Syndrome as a Case Study

Directory of Open Access Journals (Sweden)

Joel eKrueger

2012-04-01

Full Text Available Social cognition researchers have become increasingly interested in the ways that behavioral, physiological and neural coupling facilitate social interaction and interpersonal understanding. Some researchers endorse strong interactionism (SI, which conceptualizes low-level coupling processes as alternatives to higher-level individual cognitive processes; the former at least sometimes render the latter superfluous. In contrast, we espouse moderate interactionism (MI, which is an integrative approach. Its guiding assumption is that higher-level cognitive processes are likely to have been shaped by the need to coordinate, modulate and extract information from low-level coupling processes. In this paper, we present a case study on Möbius Syndrome (MS in order to contrast SI and MI. We attempt to show how MS—a rare form of congenital bilateral facial paralysis—can be a fruitful source of insight for research exploring the relation between high-level cognition and low-level coupling. Lacking a capacity for facial expression, individuals with MS are deprived of a primary channel for gestural coupling. According to SI, they lack an essential enabling feature for social interaction and interpersonal understanding more generally and thus ought to exhibit severe deficits in these areas. We challenge SI’s prediction and show how MS cases offer compelling reasons for instead adopting MI’s pluralistic model of social interaction and interpersonal understanding. We conclude that investigations of coupling processes within social interaction should inform rather than marginalize or eliminate investigation of higher-level individual cognition.

Land-Surface-Atmosphere Coupling in Observations and Models

Directory of Open Access Journals (Sweden)

Alan K Betts

2009-07-01

Full Text Available The diurnal cycle and the daily mean at the land-surface result from the coupling of many physical processes. The framework of this review is largely conceptual; looking for relationships and information in the coupling of processes in models and observations. Starting from the surface energy balance, the role of the surface and cloud albedos in the shortwave and longwave fluxes is discussed. A long-wave radiative scaling of the diurnal temperature range and the night-time boundary layer is summarized. Several aspects of the local surface energy partition are presented: the role of soilwater availability and clouds; vector methods for understanding mixed layer evolution, and the coupling between surface and boundary layer that determines the lifting condensation level. Moving to larger scales, evaporation-precipitation feedback in models is discussed; and the coupling of column water vapor, clouds and precipitation to vertical motion and moisture convergence over the Amazon. The final topic is a comparison of the ratio of surface shortwave cloud forcing to the diabatic precipitation forcing of the atmosphere in ERA-40 with observations.

Aluminium content of some processed foods, raw materials and food additives in China by inductively coupled plasma-mass spectrometry.

Science.gov (United States)

Deng, Gui-Fang; Li, Ke; Ma, Jing; Liu, Fen; Dai, Jing-Jing; Li, Hua-Bin

2011-01-01

The level of aluminium in 178 processed food samples from Shenzhen city in China was evaluated using inductively coupled plasma-mass spectrometry. Some processed foods contained a concentration of up to 1226 mg/kg, which is about 12 times the Chinese food standard. To establish the main source in these foods, Al levels in the raw materials were determined. However, aluminium concentrations in raw materials were low (0.10-451.5 mg/kg). Therefore, aluminium levels in food additives used in these foods was determined and it was found that some food additives contained a high concentration of aluminium (0.005-57.4 g/kg). The results suggested that, in the interest of public health, food additives containing high concentrations of aluminium should be replaced by those containing less. This study has provided new information on aluminium levels in Chinese processed foods, raw materials and a selection of food additives.

Thermal rectification and negative differential thermal conductance in harmonic chains with nonlinear system-bath coupling

Science.gov (United States)

Ming, Yi; Li, Hui-Min; Ding, Ze-Jun

2016-03-01

Thermal rectification and negative differential thermal conductance were realized in harmonic chains in this work. We used the generalized Caldeira-Leggett model to study the heat flow. In contrast to most previous studies considering only the linear system-bath coupling, we considered the nonlinear system-bath coupling based on recent experiment [Eichler et al., Nat. Nanotech. 6, 339 (2011), 10.1038/nnano.2011.71]. When the linear coupling constant is weak, the multiphonon processes induced by the nonlinear coupling allow more phonons transport across the system-bath interface and hence the heat current is enhanced. Consequently, thermal rectification and negative differential thermal conductance are achieved when the nonlinear couplings are asymmetric. However, when the linear coupling constant is strong, the umklapp processes dominate the multiphonon processes. Nonlinear coupling suppresses the heat current. Thermal rectification is also achieved. But the direction of rectification is reversed compared to the results of weak linear coupling constant.

HIV transmission risk among HIV seroconcordant and serodiscordant couples: dyadic processes of partner selection.

Science.gov (United States)

Eaton, Lisa A; West, Tessa V; Kenny, David A; Kalichman, Seth C

2009-04-01

Selecting sex partners of the same HIV status or serosorting is a sexual risk reduction strategy used by many men who have sex with men. However, the effectiveness of serosorting for protection against HIV is potentially limited. We sought to examine how men perceive the protective benefits of factors related to serosorting including beliefs about engaging in serosorting, sexual communication, and perceptions of risk for HIV. Participants were 94 HIV negative seroconcordant (same HIV status) couples, 20 HIV serodiscordant (discrepant HIV status) couples, and 13 HIV positive seroconcordant (same HIV status) couples recruited from a large gay pride festival in the southeastern US. To account for nonindependence found in the couple-level data, we used multilevel modeling which includes dyad in the analysis. Findings demonstrated that participants in seroconcordant relationships were more likely to believe that serosorting reduces concerns for condom use. HIV negative participants in seroconcordant relationships viewed themselves at relatively low risk for HIV transmission even though monogamy within relationships and HIV testing were infrequent. Dyadic analyses demonstrated that partners have a substantial effect on an individual's beliefs and number of unprotected sex partners. We conclude that relationship partners are an important source of influence and, thus, intervening with partners is necessary to reduce HIV transmission risks.

A transmission and reflection coupled ultrasonic process tomography based on cylindrical miniaturized transducers using PVDF films

Science.gov (United States)

Gu, J.; Yang, H.; Fan, F.; Su, M.

2017-12-01

A transmission and reflection coupled ultrasonic process tomography has been developed, which is characterized by a proposed dual-mode (DM) reconstruction algorithm, as well as an adaptive search approach to determine an optimal image threshold during the image binarization. In respect of hardware, to improve the accuracy of time-of-flight (TOF) and extend the lowest detection limit of particle size, a cylindrical miniaturized transducer using polyvinylidene fluoride (PVDF) films is designed. Besides, the development of range-gating technique for the identification of transmission and reflection waves in scanning is discussed. A particle system with four iron particles is then investigated numerically and experimentally to evaluate these proposed methods. The sound pressure distribution in imaging area is predicted numerically, followed by the analysis of the relationship between the emitting surface width of transducer and particle size. After the processing of experimental data for effective waveform extraction and fusion, the comparison between reconstructed results from transmission-mode (TM), reflection-mode (RM), and dual-mode reconstructions is carried out and the latter manifests obvious improvements from the blurring reduction to the enhancement of particle boundary.

Mass transport in low permeability rocks under the influence of coupled thermomechanical and hydrochemical effects - an overview

International Nuclear Information System (INIS)

Tsang, C.F.

1984-10-01

The present paper gives a general overview of mass transport in low permeability rocks under the coupled thermomechanical and hydrochemical effects associated with a nuclear waste repository. A classification of coupled processes is given. Then an ess is presented. example of a coupled process is presented. Discussions of coupled processes based on a recent LBL Panel meeting are summarized. 5 references, 3 figures, 4 tables

A finite range coupled channel Born approximation code

International Nuclear Information System (INIS)

Nagel, P.; Koshel, R.D.

1978-01-01

The computer code OUKID calculates differential cross sections for direct transfer nuclear reactions in which multistep processes, arising from strongly coupled inelastic states in both the target and residual nuclei, are possible. The code is designed for heavy ion reactions where full finite range and recoil effects are important. Distorted wave functions for the elastic and inelastic scattering are calculated by solving sets of coupled differential equations using a Matrix Numerov integration procedure. These wave functions are then expanded into bases of spherical Bessel functions by the plane-wave expansion method. This approach allows the six-dimensional integrals for the transition amplitude to be reduced to products of two one-dimensional integrals. Thus, the inelastic scattering is treated in a coupled channel formalism while the transfer process is treated in a finite range born approximation formalism. (Auth.)

Modeling of coupled heat transfer and reactive transport processes in porous media: Application to seepage studies at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Mukhopadhyay, Sumit; Sonnenthal, Eric L.; Spycher, Nicolas

2007-01-01

When hot radioactive waste is placed in subsurface tunnels, a series of complex changes occurs in the surrounding medium. The water in the pore space of the medium undergoes vaporization and boiling. Subsequently, vapor migrates out of the matrix pore space, moving away from the tunnel through the permeable fracture network. This migration is propelled by buoyancy, by the increased vapor pressure caused by heating and boiling, and through local convection. In cooler regions, the vapor condenses on fracture walls, where it drains through the fracture network. Slow imbibition of water thereafter leads to gradual rewetting of the rock matrix. These thermal and hydrological processes also bring about chemical changes in the medium. Amorphous silica precipitates from boiling and evaporation, and calcite from heating and CO2 volatilization. The precipitation of amorphous silica, and to a much lesser extent calcite, results in long-term permeability reduction. Evaporative concentration also results in the precipitation of gypsum (or anhydrite), halite, fluorite and other salts. These evaporative minerals eventually redissolve after the boiling period is over, however, their precipitation results in a significant temporary decrease in permeability. Reduction of permeability is also associated with changes in fracture capillary characteristics. In short, the coupled thermal-hydrological-chemical (THC) processes dynamically alter the hydrological properties of the rock. A model based on the TOUGHREACT reactive transport software is presented here to investigate the impact of THC processes on flow near an emplacement tunnel at Yucca Mountain, Nevada. We show how transient changes in hydrological properties caused by THC processes often lead to local flow channeling and saturation increases above the tunnel. For models that include only permeability changes to fractures, such local flow channeling may lead to seepage relative to models where THC effects are ignored. However

Modeling of coupled heat transfer and reactive transport processes in porous media: Application to seepage studies at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Mukhopadhyay, S.; Sonnenthal, E.L.; Spycher, N.

2007-01-01

When hot radioactive waste is placed in subsurface tunnels, a series of complex changes occurs in the surrounding medium. The water in the pore space of the medium undergoes vaporization and boiling. Subsequently, vapor migrates out of the matrix pore space, moving away from the tunnel through the permeable fracture network. This migration is propelled by buoyancy, by the increased vapor pressure caused by heating and boiling, and through local convection. In cooler regions, the vapor condenses on fracture walls, where it drains through the fracture network. Slow imbibition of water thereafter leads to gradual rewetting of the rock matrix. These thermal and hydrological processes also bring about chemical changes in the medium. Amorphous silica precipitates from boiling and evaporation, and calcite from heating and CO 2 volatilization. The precipitation of amorphous silica, and to a much lesser extent calcite, results in long-term permeability reduction. Evaporative concentration also results in the precipitation of gypsum (or anhydrite), halite, fluorite and other salts. These evaporative minerals eventually redissolve after the boiling period is over, however, their precipitation results in a significant temporary decrease in permeability. Reduction of permeability is also associated with changes in fracture capillary characteristics. In short, the coupled thermal-hydrological-chemical (THC) processes dynamically alter the hydrological properties of the rock. A model based on the TOUGHREACT reactive transport software is presented here to investigate the impact of THC processes on flow near an emplacement tunnel at Yucca Mountain, Nevada. We show how transient changes in hydrological properties caused by THC processes often lead to local flow channeling and saturation increases above the tunnel. For models that include only permeability changes to fractures, such local flow channeling may lead to seepage relative to models where THC effects are ignored. However

Reconstituting racial histories and identities: the narratives of interracial couples.

Science.gov (United States)

Killian, K D

2001-01-01

This study explores the process by which interracial spouses construct narratives about their racial histories, identities, and experiences in their relationship together. Ten black-white couples were interviewed individually and conjointly. The results reflected interracial spouses' experience of their life together, their perception of others' perceptions of them, and their unique processes of negotiating racial, gender, and class differences. Black spouses, compared with white spouses, demonstrated a greater awareness of and sensitivity to social resistance to interracial couples, and black spouses' familial and personal histories were sometimes relegated to silence in the couple relationship. I discuss recommendations for marriage and family therapists working with interracial spouses.

Palladium-Catalyzed Suzuki–Miyaura Cross-Coupling in Continuous Flow

Directory of Open Access Journals (Sweden)

Christophe Len

2017-05-01

Full Text Available Carbon–carbon cross-coupling reactions are among the most important processes in organic chemistry and Suzuki–Miyaura reactions are the most widely used protocols. For a decade, green chemistry and particularly catalysis and continuous flow, have shown immense potential in achieving the goals of “greener synthesis”. To date, it seems difficult to conceive the chemistry of the 21st century without the industrialization of continuous flow process in the area of pharmaceuticals, drugs, agrochemicals, polymers, etc. A large variety of palladium Suzuki–Miyaura cross-coupling reactions have been developed using a continuous flow sequence for preparing the desired biaryl derivatives. Our objective is to focus this review on the continuous flow Suzuki–Miyaura cross-coupling using homogeneous and heterogeneous catalysts.

Coupled processes of fluid flow, solute transport, and geochemical reactions in reactive barriers

Energy Technology Data Exchange (ETDEWEB)

Kim, Jeongkon; Schwartz, Franklin W.; Xu, Tianfu; Choi, Heechul, and Kim, In S.

2004-01-02

A complex pattern of coupling between fluid flow and mass transport develops when heterogeneous reactions occur. For instance, dissolution and precipitation reactions can change a porous medium's physical properties, such as pore geometry and thus permeability. These changes influence fluid flow, which in turn impacts the composition of dissolved constituents and the solid phases, and the rate and direction of advective transport. Two-dimensional modeling studies using TOUGHREACT were conducted to investigate the coupling between flow and transport developed as a consequence of differences in density, dissolution precipitation, and medium heterogeneity. The model includes equilibrium reactions for aqueous species, kinetic reactions between the solid phases and aqueous constituents, and full coupling of porosity and permeability changes resulting from precipitation and dissolution reactions in porous media. In addition, a new permeability relationship is implemented in TOUGHREACT to examine the effects of geochemical reactions and density difference on plume migration in porous media. Generally, the evolutions in the concentrations of the aqueous phase are intimately related to the reaction-front dynamics. Plugging of the medium contributed to significant transients in patterns of flow and mass transport.

Oscillating systems with cointegrated phase processes

DEFF Research Database (Denmark)

Østergaard, Jacob; Rahbek, Anders; Ditlevsen, Susanne

2017-01-01

We present cointegration analysis as a method to infer the network structure of a linearly phase coupled oscillating system. By defining a class of oscillating systems with interacting phases, we derive a data generating process where we can specify the coupling structure of a network...... that resembles biological processes. In particular we study a network of Winfree oscillators, for which we present a statistical analysis of various simulated networks, where we conclude on the coupling structure: the direction of feedback in the phase processes and proportional coupling strength between...... individual components of the system. We show that we can correctly classify the network structure for such a system by cointegration analysis, for various types of coupling, including uni-/bi-directional and all-to-all coupling. Finally, we analyze a set of EEG recordings and discuss the current...

Feedback control of coupled-bunch instabilities

International Nuclear Information System (INIS)

Fox, J.D.; Eisen, N.; Hindi, H.; Linscott, I.; Oxoby, G.; Sapozhnikov, L.; Serio, M.

1993-05-01

The next generation of synchrotron light sources and particle accelerators will require active feedback systems to control multi-bunch instabilities. Stabilizing hundreds or thousands of potentially unstable modes in these accelerator designs presents many technical challenges. Feedback systems to stabilize coupled-bunch instabilities may be understood in the frequency domain (mode-based feedback) or in the time domain (bunch-by-bunch feedback). In both approaches an external amplifier system is used to create damping fields that prevent coupled-bunch oscillations from growing without bound. The system requirements for transverse (betatron) and longitudinal (synchrotron) feedback are presented, and possible implementation options developed. Feedback system designs based on digital signal-processing techniques are described. Experimental results are shown from a synchrotron oscillation damper in the SSRL/SLAC storage ring SPEAR that uses digital signal-processing techniques

Coupled Transport/Reaction Modelling of Copper Canister Corrosion Aided by Microbial Processes

Energy Technology Data Exchange (ETDEWEB)

Liu, Jinsong [Royal Institute of Technology, Stockholm (Sweden). Dept. of Chemical Engineering and Technology

2006-04-15

Copper canister corrosion is an important issue in the concept of a nuclear fuel repository. Previous studies indicate that the oxygen-free copper canister could hold its integrity for more than 100,000 years in the repository environment. Microbial processes may reduce sulphate to sulphide and considerably increase the amount of sulphides available for corrosion. In this paper, a coupled transport/reaction model is developed to account for the transport of chemical species produced by microbial processes. The corroding agents like sulphide would come not only from the groundwater flowing in a fracture that intersects the canister, but also from the reduction of sulphate near the canister. The reaction of sulphate-reducing bacteria and the transport of sulphide in the bentonite buffer are included in the model. The depth of copper canister corrosion is calculated by the model. With representative 'central values' of the concentrations of sulphate and methane at repository depth at different sites in Fennoscandian Shield the corrosion depth predicted by the model is a few millimetres during 10{sup 5} years. As the concentrations of sulphate and methane are extremely site-specific and future climate changes may significantly influence the groundwater compositions at potential repository sites, sensitivity analyses have been conducted. With a broad perspective of the measured concentrations at different sites in Sweden and in Finland, and some possible mechanisms (like the glacial meltwater intrusion and interglacial seawater intrusion) that may introduce more sulphate into the groundwater at intermediate depths during future climate changes, higher concentrations of either/both sulphate and methane than what is used as the representative 'central' values would be possible. In worst cases. locally, half of the canister thickness could possibly be corroded within 10{sup 5} years.

Coupled Transport/Reaction Modelling of Copper Canister Corrosion Aided by Microbial Processes

International Nuclear Information System (INIS)

Jinsong Liu

2006-04-01

Copper canister corrosion is an important issue in the concept of a nuclear fuel repository. Previous studies indicate that the oxygen-free copper canister could hold its integrity for more than 100,000 years in the repository environment. Microbial processes may reduce sulphate to sulphide and considerably increase the amount of sulphides available for corrosion. In this paper, a coupled transport/reaction model is developed to account for the transport of chemical species produced by microbial processes. The corroding agents like sulphide would come not only from the groundwater flowing in a fracture that intersects the canister, but also from the reduction of sulphate near the canister. The reaction of sulphate-reducing bacteria and the transport of sulphide in the bentonite buffer are included in the model. The depth of copper canister corrosion is calculated by the model. With representative 'central values' of the concentrations of sulphate and methane at repository depth at different sites in Fennoscandian Shield the corrosion depth predicted by the model is a few millimetres during 10 5 years. As the concentrations of sulphate and methane are extremely site-specific and future climate changes may significantly influence the groundwater compositions at potential repository sites, sensitivity analyses have been conducted. With a broad perspective of the measured concentrations at different sites in Sweden and in Finland, and some possible mechanisms (like the glacial meltwater intrusion and interglacial seawater intrusion) that may introduce more sulphate into the groundwater at intermediate depths during future climate changes, higher concentrations of either/both sulphate and methane than what is used as the representative 'central' values would be possible. In worst cases. locally, half of the canister thickness could possibly be corroded within 10 5 years

Coupled Transport/Reaction Modelling of Copper Canister Corrosion Aided by Microbial Processes

Energy Technology Data Exchange (ETDEWEB)

Jinsong Liu [Royal Institute of Technology, Stockholm (Sweden). Dept. of Chemical Engineering and Technology

2006-04-15

Copper canister corrosion is an important issue in the concept of a nuclear fuel repository. Previous studies indicate that the oxygen-free copper canister could hold its integrity for more than 100,000 years in the repository environment. Microbial processes may reduce sulphate to sulphide and considerably increase the amount of sulphides available for corrosion. In this paper, a coupled transport/reaction model is developed to account for the transport of chemical species produced by microbial processes. The corroding agents like sulphide would come not only from the groundwater flowing in a fracture that intersects the canister, but also from the reduction of sulphate near the canister. The reaction of sulphate-reducing bacteria and the transport of sulphide in the bentonite buffer are included in the model. The depth of copper canister corrosion is calculated by the model. With representative 'central values' of the concentrations of sulphate and methane at repository depth at different sites in Fennoscandian Shield the corrosion depth predicted by the model is a few millimetres during 10{sup 5} years. As the concentrations of sulphate and methane are extremely site-specific and future climate changes may significantly influence the groundwater compositions at potential repository sites, sensitivity analyses have been conducted. With a broad perspective of the measured concentrations at different sites in Sweden and in Finland, and some possible mechanisms (like the glacial meltwater intrusion and interglacial seawater intrusion) that may introduce more sulphate into the groundwater at intermediate depths during future climate changes, higher concentrations of either/both sulphate and methane than what is used as the representative 'central' values would be possible. In worst cases. locally, half of the canister thickness could possibly be corroded within 10{sup 5} years.

Results From an International Simulation Study on Coupled Thermal, Hydrological, and Mechanical (THM) Processes Near Geological Nuclear Waste Repositories

International Nuclear Information System (INIS)

J. Rutqvist; D. Barr; J.T. Birkholzer; M. Chijimatsu; O. Kolditz; Q. Liu; Y. Oda; W. Wang; C. Zhang

2006-01-01

As part of the ongoing international DECOVALEX project, four research teams used five different models to simulate coupled thermal, hydrological, and mechanical (THM) processes near waste emplacement drifts of geological nuclear waste repositories. The simulations were conducted for two generic repository types, one with open and the other with back-filled repository drifts, under higher and lower postclosure temperatures, respectively. In the completed first model inception phase of the project, a good agreement was achieved between the research teams in calculating THM responses for both repository types, although some disagreement in hydrological responses is currently being resolved. In particular, good agreement in the basic thermal-mechanical responses was achieved for both repository types, even though some teams used relatively simplified thermal-elastic heat-conduction models that neglected complex near-field thermal-hydrological processes. The good agreement between the complex and simplified process models indicates that the basic thermal-mechanical responses can be predicted with a relatively high confidence level

Mode coupling in spin torque oscillators

International Nuclear Information System (INIS)

Zhang, Steven S.-L.; Zhou, Yan; Li, Dong; Heinonen, Olle

2016-01-01

A number of recent experimental works have shown that the dynamics of a single spin torque oscillator can exhibit complex behavior that stems from interactions between two or more modes of the oscillator, such as observed mode-hopping or mode coexistence. There has been some initial work indicating how the theory for a single-mode (macro-spin) spin torque oscillator should be generalized to include several modes and the interactions between them. In the present work, we rigorously derive such a theory starting with the Landau–Lifshitz–Gilbert equation for magnetization dynamics by expanding up to third-order terms in deviation from equilibrium. Our results show how a linear mode coupling, which is necessary for observed mode-hopping to occur, arises through coupling to a magnon bath. The acquired temperature dependence of this coupling implies that the manifold of orbits and fixed points may shift with temperature. - Highlights: • Deriving equations for coupled modes in spin torque oscillators. • Including Hamiltonian formalism and elimination of three–magnon processes. • Thermal bath of magnons central to mode coupling. • Numerical examples of circular and elliptical devices.

Mode coupling in spin torque oscillators

Energy Technology Data Exchange (ETDEWEB)

Zhang, Steven S.-L., E-mail: ZhangShule@missouri.edu [Department of Physics and Astronomy, University of Missouri, Columbia, MO 65211 (United States); Zhou, Yan, E-mail: yanzhou@hku.hk [Department of Physics, The University of Hong Kong, Hong Kong (China); Center of Theoretical and Computational Physics, University of Hong Kong, Hong Kong (China); Li, Dong, E-mail: geodesic.ld@gmail.com [Department of Physics, Centre for Nonlinear Studies, and Beijing-Hong Kong-Singapore Joint Centre for Nonlinear and Complex Systems, Hong Kong Baptist University, Kowloon Tong, Hong Kong (China); Heinonen, Olle, E-mail: heinonen@anl.gov [Material Science Division, Argonne National Laboratory, Lemont, IL 60439 (United States); Northwestern-Argonne Institute of Science and Technology, 2145 Sheridan Road, Evanston, IL 60208 (United States); Computation Institute, The Unversity of Chicago, 5735 S Ellis Avenue, Chicago, IL 60637 (United States)

2016-09-15

A number of recent experimental works have shown that the dynamics of a single spin torque oscillator can exhibit complex behavior that stems from interactions between two or more modes of the oscillator, such as observed mode-hopping or mode coexistence. There has been some initial work indicating how the theory for a single-mode (macro-spin) spin torque oscillator should be generalized to include several modes and the interactions between them. In the present work, we rigorously derive such a theory starting with the Landau–Lifshitz–Gilbert equation for magnetization dynamics by expanding up to third-order terms in deviation from equilibrium. Our results show how a linear mode coupling, which is necessary for observed mode-hopping to occur, arises through coupling to a magnon bath. The acquired temperature dependence of this coupling implies that the manifold of orbits and fixed points may shift with temperature. - Highlights: • Deriving equations for coupled modes in spin torque oscillators. • Including Hamiltonian formalism and elimination of three–magnon processes. • Thermal bath of magnons central to mode coupling. • Numerical examples of circular and elliptical devices.

Efficient modeling of reactive transport phenomena by a multispecies random walk coupled to chemical equilibrium

International Nuclear Information System (INIS)

Pfingsten, W.

1996-01-01

Safety assessments for radioactive waste repositories require a detailed knowledge of physical, chemical, hydrological, and geological processes for long time spans. In the past, individual models for hydraulics, transport, or geochemical processes were developed more or less separately to great sophistication for the individual processes. Such processes are especially important in the near field of a waste repository. Attempts have been made to couple at least two individual processes to get a more adequate description of geochemical systems. These models are called coupled codes; they couple predominantly a multicomponent transport model with a chemical reaction model. Here reactive transport is modeled by the sequentially coupled code MCOTAC that couples one-dimensional advective, dispersive, and diffusive transport with chemical equilibrium complexation and precipitation/dissolution reactions in a porous medium. Transport, described by a random walk of multispecies particles, and chemical equilibrium calculations are solved separately, coupled only by an exchange term. The modular-structured code was applied to incongruent dissolution of hydrated silicate gels, to movement of multiple solid front systems, and to an artificial, numerically difficult heterogeneous redox problem. These applications show promising features with respect to applicability to relevant problems and possibilities of extensions

A novel polygeneration process to co-produce ethylene and electricity from shale gas with zero CO2 emissions via methane oxidative coupling

International Nuclear Information System (INIS)

Khojasteh Salkuyeh, Yaser; Adams, Thomas A.

2015-01-01

Highlights: • Development of an ethylene plant from shale gases with zero CO 2 emissions. • Oxidative coupling of methane is used for the conversion of gas to ethylene. • Polygeneration strategy is used to improve the profitability of plant. - Abstract: A techno-economic analysis of a novel process to co-produce ethylene and electricity using a recently developed methane oxidative coupling catalyst is presented. Several design variants are considered, featuring the use of traditional gas turbines, chemical looping combustion, and 100% carbon dioxide capture. Mass and energy balance simulations were carried out using Aspen Plus simulations, and particle swarm optimization was used to determine the optimal process design under a variety of market scenarios. A custom model for the gas turbine section was used to ensure that the negative impacts of various cooling strategies were factored into the analysis. The results show that by synergistically co-producing power and ethylene using this catalyst, ethylene can be produced at costs close to traditional steam cracking methods with nearly zero carbon dioxide emissions, even when factoring in the relatively poor conversion and selectivity of the chosen catalyst

Development of a parallel processing couple for calculations of control rod worth in terms of burn-up in a WWER-1000 reactor

Energy Technology Data Exchange (ETDEWEB)

Noori-Kalkhoran, Omid; Ahangari, R. [Nuclear Science and Technology Research Institute (NSTRI), Tehran (Iran, Islamic Republic of). Reactor Research school; Shirani, A.S. [Shahid Beheshti Univ., Tehran (Iran, Islamic Republic of). Faculty of Engineering

2017-03-15

In this study a code based method has been developed for calculation of integral and differential control rod worth in terms of burn-up for a WWER-1000 reactor. Parallel processing of WIMSD-5B, PARCS V2.7 and COBRA-EN has been used for this purpose. WIMSD-5B has been used for cell calculation and handling burn-up of core at different days. PARCS V2.7?has been used for neutronic calculation of core and critical boron concentration search. Thermal-hydraulic calculation has been performed by COBRA-EN. A Parallel processing algorithm has been developed by MATLAB to couple and transfer suitable data between these codes in each step. Steady-State Power Picking Factors (PPFs) of the core and Control rod worth have been calculated from Beginning Of Cycle (BOC) to 289.7 Effective full Power Days (EFPDs) in some steps. Results have been compared with Bushehr Nuclear Power Plant (BNPP) Final Safety Analysis Report (FSAR) results. The results show great similarity and confirm the ability of developed coupling in calculation of control rod worth in terms of burn-up.

Coherence protection in coupled quantum systems

Science.gov (United States)

Cammack, H. M.; Kirton, P.; Stace, T. M.; Eastham, P. R.; Keeling, J.; Lovett, B. W.

2018-02-01

The interaction of a quantum system with its environment causes decoherence, setting a fundamental limit on its suitability for quantum information processing. However, we show that if the system consists of coupled parts with different internal energy scales then the interaction of one part with a thermal bath need not lead to loss of coherence from the other. Remarkably, we find that the protected part can remain coherent for longer when the coupling to the bath becomes stronger or the temperature is raised. Our theory will enable the design of decoherence-resistant hybrid quantum computers.

Ultrastrong exciton-photon coupling in single and coupled organic microcavities

Science.gov (United States)

Liu, Bin; Bramante, Rosemary; Valle, Brent; Singer, Kenneth; Khattab, Tawfik; Williams, Jarrod; Twieg, Robert

2015-03-01

We have demonstrated ultrastrong light-matter coupling in organic planar microcavities composed of a neat glassy organic dye film between two metallic (aluminum) mirrors in a half-cavity configuration. Such cavities are characterized by Q factors around 10. Tuning the thickness of the organic layer enables the observation of the ultrastrong coupling regime. Via reflectivity measurements, we observe a very large Rabi splitting around 1.227 eV between upper and lower polariton branches at room temperature, and we detect polariton emission from the lower polariton branch via photoluminescence measurements. The large splitting is due to the large oscillator strength of the neat dye glass, and to the match of the low-Q cavity spectral width to the broad absorption width of the dye film material. We also study the interaction between excitonic states of neat glassy organic dye and cavity modes within coupled microcavity structures. The high-reflectivity mirrors are formed from distributed Bragg reflectors (DBR), which are multilayer films fabricated using the coextrusion process, containing alternating layers of high (SAN25, n =1.57) and low (Dyneon THV 220G, n =1.37) refractive index dielectric polymers. Nonlinear optical measurements will be discussed. This research was supported by the National Science Foundation Center for Layered Polymer Systems (CLiPS) under Grant Number DMR-0423914.

Numerical simulation of interior ballistic process of railgun based on the multi-field coupled model

Directory of Open Access Journals (Sweden)

Qinghua Lin

2016-04-01

Full Text Available Railgun launcher design relies on appropriate models. A multi-field coupled model of railgun launcher was presented in this paper. The 3D transient multi-field was composed of electromagnetic field, thermal field and structural field. The magnetic diffusion equations were solved by a finite-element boundary-element coupling method. The thermal diffusion equations and structural equations were solved by a finite element method. A coupled calculation was achieved by the transfer data from the electromagnetic field to the thermal and structural fields. Some characteristics of railgun shot, such as velocity skin effect, melt-wave erosion and magnetic sawing, which are generated under the condition of large-current and high-speed sliding electrical contact, were demonstrated by numerical simulation.

Deterministic Diffusion in Delayed Coupled Maps

International Nuclear Information System (INIS)

Sozanski, M.

2005-01-01

Coupled Map Lattices (CML) are discrete time and discrete space dynamical systems used for modeling phenomena arising in nonlinear systems with many degrees of freedom. In this work, the dynamical and statistical properties of a modified version of the CML with global coupling are considered. The main modification of the model is the extension of the coupling over a set of local map states corresponding to different time iterations. The model with both stochastic and chaotic one-dimensional local maps is studied. Deterministic diffusion in the CML under variation of a control parameter is analyzed for unimodal maps. As a main result, simple relations between statistical and dynamical measures are found for the model and the cases where substituting nonlinear lattices with simpler processes is possible are presented. (author)

Incorporating Ecosystem Processes Controlling Carbon Balance Into Models of Coupled Human-Natural Systems

Science.gov (United States)

Currie, W.; Brown, D. G.; Brunner, A.; Fouladbash, L.; Hadzick, Z.; Hutchins, M.; Kiger, S. E.; Makino, Y.; Nassauer, J. I.; Robinson, D. T.; Riolo, R. L.; Sun, S.

2012-12-01

A key element in the study of coupled human-natural systems is the interactions of human populations with vegetation and soils. In human-dominated landscapes, vegetation production and change results from a combination of ecological processes and human decision-making and behavior. Vegetation is often dramatically altered, whether to produce food for humans and livestock, to harvest fiber for construction and other materials, to harvest fuel wood or feedstock for biofuels, or simply for cultural preferences as in the case of residential lawns with sparse trees in the exurban landscape. This alteration of vegetation and its management has a substantial impact on the landscape carbon balance. Models can be used to simulate scenarios in human-natural systems and to examine the integration of processes that determine future trajectories of carbon balance. However, most models of human-natural systems include little integration of the human alteration of vegetation with the ecosystem processes that regulate carbon balance. Here we illustrate a few case studies of pilot-study models that strive for this integration from our research across various types of landscapes. We focus greater detail on a fully developed research model linked to a field study of vegetation and soils in the exurban residential landscape of Southeastern Michigan, USA. The field study characterized vegetation and soil carbon storage in 5 types of ecological zones. Field-observed carbon storage in the vegetation in these zones ranged widely, from 150 g C/m2 in turfgrass zones, to 6,000 g C/m2 in zones defined as turfgrass with sparse woody vegetation, to 16,000 g C/m2 in a zone defined as dense trees and shrubs. Use of these zones facilitated the scaling of carbon pools to the landscape, where the areal mixtures of zone types had a significant impact on landscape C storage. Use of these zones also facilitated the use of the ecosystem process model Biome-BGC to simulate C trajectories and also

Synchronizing spiral waves in a coupled Rössler system

International Nuclear Information System (INIS)

Gao Jia-Zhen; Yang Shu-Xin; Xie Ling-Ling; Gao Ji-Hua

2011-01-01

The synchronisation of spiral patterns in a drive-response Rössler system is studied. The existence of three types of synchronisation is revealed by inspecting the coupling parameter space. Two transient stages of phase synchronisation and partial synchronisation are observed in a comparatively weak feedback coupling parameter regime, whilst complete synchronisation of spirals is found with strong negative couplings. Detailed observations of the synchronous process, such as oscillatory frequencies, parameters mismatches and amplitude variations, etc, are investigated via numerical simulations. (general)

Coupled-channels analyses for 9,11Li + 208Pb fusion reactions with multi-neutron transfer couplings

Science.gov (United States)

Choi, Ki-Seok; Cheoun, Myung-Ki; So, W. Y.; Hagino, K.; Kim, K. S.

2018-05-01

We discuss the role of two-neutron transfer processes in the fusion reaction of the 9,11Li + 208Pb systems. We first analyze the 9Li + 208Pb reaction by taking into account the coupling to the 7Li + 210Pb channel. To this end, we assume that two neutrons are directly transferred to a single effective channel in 210Pb and solve the coupled-channels equations with the two channels. By adjusting the coupling strength and the effective Q-value, we successfully reproduce the experimental fusion cross sections for this system. We then analyze the 11Li + 208Pb reaction in a similar manner, that is, by taking into account three effective channels with 11Li + 208Pb, 9Li + 210Pb, and 7Li + 212Pb partitions. In order to take into account the halo structure of the 11Li nucleus, we construct the potential between 11Li and 208Pb with a double folding procedure, while we employ a Woods-Saxon type potential with the global Akyüz-Winther parameters for the other channels. Our calculation indicates that the multiple two-neutron transfer process plays a crucial role in the 11Li + 208Pb fusion reaction at energies around the Coulomb barrier.

Strong coupling constant extraction from high-multiplicity Z +jets observables

Science.gov (United States)

Johnson, Mark; Maître, Daniel

2018-03-01

We present a strong coupling constant extraction at next-to-leading order QCD accuracy using ATLAS Z +2 ,3,4 jets data. This is the first extraction using processes with a dependency on high powers of the coupling constant. We obtain values of the strong coupling constant at the Z mass compatible with the world average and with uncertainties commensurate with other next-to-leading order extractions at hadron colliders. Our most conservative result for the strong coupling constant is αS(MZ)=0.117 8-0.0043+0.0051 .

A global view on the Higgs self-coupling at lepton colliders

Energy Technology Data Exchange (ETDEWEB)

Di Vita, Stefano [INFN Sezione di Milano (Italy); Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Durieux, Gauthier [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Grojean, Christophe [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Humboldt-Universitaet, Berlin (Germany). Inst. fuer Physik; Gu, Jiayin [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Chinese Academy of Sciences, Beijing (China). Center for Future High Energy Physics; Liu, Zhen [Fermi National Accelerator Laboratory, Batavia, IL (United States). Theoretical Physics Dept.; Panico, Giuliano [Univ. Autonoma de Barcelona (Spain). IFAE; Univ. Autonoma de Barcelona (Spain). BIST; Riembau, Marc; Vantalon, Thibaud [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Univ. Autonoma de Barcelona (Spain). IFAE; Univ. Autonoma de Barcelona (Spain). BIST

2017-11-15

We perform a global effective-field-theory analysis to assess the precision on the determination of the Higgs trilinear self-coupling at future lepton colliders. Two main scenarios are considered, depending on whether the center-of-mass energy of the colliders is sufficient or not to access Higgs pair production processes. Low-energy machines allow for ∝40% precision on the extraction of the Higgs trilinear coupling through the exploitation of next-to-leading-order effects in single Higgs measurements, provided that runs at both 240/250 GeV and 350 GeV are available with luminosities in the few attobarns range. A global fit, including possible deviations in other SM couplings, is essential in this case to obtain a robust determination of the Higgs self-coupling. High-energy machines can easily achieve a ∝20% precision through Higgs pair production processes. In this case, the impact of additional coupling modifications is milder, although not completely negligible.

A global view on the Higgs self-coupling at lepton colliders

International Nuclear Information System (INIS)

Di Vita, Stefano; Durieux, Gauthier; Grojean, Christophe; Humboldt-Universitaet, Berlin; Gu, Jiayin; Chinese Academy of Sciences, Beijing; Liu, Zhen; Panico, Giuliano; Univ. Autonoma de Barcelona; Riembau, Marc; Vantalon, Thibaud; Univ. Autonoma de Barcelona; Univ. Autonoma de Barcelona

2017-11-01

We perform a global effective-field-theory analysis to assess the precision on the determination of the Higgs trilinear self-coupling at future lepton colliders. Two main scenarios are considered, depending on whether the center-of-mass energy of the colliders is sufficient or not to access Higgs pair production processes. Low-energy machines allow for ∝40% precision on the extraction of the Higgs trilinear coupling through the exploitation of next-to-leading-order effects in single Higgs measurements, provided that runs at both 240/250 GeV and 350 GeV are available with luminosities in the few attobarns range. A global fit, including possible deviations in other SM couplings, is essential in this case to obtain a robust determination of the Higgs self-coupling. High-energy machines can easily achieve a ∝20% precision through Higgs pair production processes. In this case, the impact of additional coupling modifications is milder, although not completely negligible.

The feasibility of modelling coupled processes in safety analysis of spent nuclear fuel disposal

Energy Technology Data Exchange (ETDEWEB)

Rasilainen, K. [VTT Energy, Espoo (Finland); Luukkonen, A.; Niemi, A.; Poellae, J. [VTT Communities and Infrastructure, Espoo (Finland); Olin, M. [VTT Chemical Technology, Espoo (Finland)

1999-07-01

The potential of applying coupled modelling in the Finnish safety analysis programme has been reviewed. The study focused on the migration of radionuclides escaping from a spent fuel repository planned to be excavated in fractured bedrock. Two effects that can trigger various couplings in and around a spent fuel repository in Finland were studied in detail; namely heat generation in the spent fuel and the presence of deep, saline groundwaters. The latter have been observed in coastal areas. A systematic survey of the requirements of coupled modelling identified features that render such migration calculations a challenging task. In groundwater flow modelling there appears to be wide ranging uncertainty related to conceptualisation of flow systems and to the corresponding input data. In terms of migration related chemistry there appear to be large gaps in the underlying thermodynamic database for geochemical systems. Rock mechanical predictions are heavily dependent on knowing the location, structure and properties of dominant fractures; information which is extremely difficult to obtain. Conduction and convection of heat is understood well in principle. On the basis of this review, it appears that coupled migration modelling may not yet be at the stage of development that would allow its use as a standard modelling tool in performance assessments. However, a firmer basis for the conclusions reached can only be obtained after a systematic modelling exercise on a relevant and real migration problem has been carried out. (orig.)

The feasibility of modelling coupled processes in safety analysis of spent nuclear fuel disposal

International Nuclear Information System (INIS)

Rasilainen, K.; Luukkonen, A.; Niemi, A.; Poellae, J.; Olin, M.

1999-01-01

The potential of applying coupled modelling in the Finnish safety analysis programme has been reviewed. The study focused on the migration of radionuclides escaping from a spent fuel repository planned to be excavated in fractured bedrock. Two effects that can trigger various couplings in and around a spent fuel repository in Finland were studied in detail; namely heat generation in the spent fuel and the presence of deep, saline groundwaters. The latter have been observed in coastal areas. A systematic survey of the requirements of coupled modelling identified features that render such migration calculations a challenging task. In groundwater flow modelling there appears to be wide ranging uncertainty related to conceptualisation of flow systems and to the corresponding input data. In terms of migration related chemistry there appear to be large gaps in the underlying thermodynamic database for geochemical systems. Rock mechanical predictions are heavily dependent on knowing the location, structure and properties of dominant fractures; information which is extremely difficult to obtain. Conduction and convection of heat is understood well in principle. On the basis of this review, it appears that coupled migration modelling may not yet be at the stage of development that would allow its use as a standard modelling tool in performance assessments. However, a firmer basis for the conclusions reached can only be obtained after a systematic modelling exercise on a relevant and real migration problem has been carried out. (orig.)

Dynamical behaviour of the coupled diffusion map lattice

International Nuclear Information System (INIS)

Wei Wang; Cerdeira, H.A.

1993-10-01

In this paper we report the dynamical study of a coupled diffusive map lattice with the coupling between the elements only through the bifurcation parameter of the mapping function. The diffusive process of the lattice from an initially random distribution state to a homogeneous one and the stable range of the diffusive homogeneous attractor are discussed. For various coupling strengths we find that there are several types of spatio-temporal structures. In addition, the evolution of the lattice into chaos is studied and a largest Lyapunov exponent is used to characterize the dynamical behaviour. (author). 22 refs, 9 figs

Application of coupled nanoscale resonators for spectral sensing

International Nuclear Information System (INIS)

Nefedov, N

2009-01-01

In this paper we propose a method to perform tunable spectral sensing using globally inhibitory coupled oscillators. The suggested system may operate in the analog radio frequency (RF) domain without high speed ADC and heavy digital signal processing. Oscillator arrays may be made of imprecise elements such as nanoresonators. Provided there is a proper coupling, the system dynamics can be made stable despite the imprecision of the components. Global coupling could be implemented using a common load and controlled by digital means to tune the bandwidth. This method may be used for spectral sensing in cognitive radio terminals.

Application of coupled nanoscale resonators for spectral sensing

Energy Technology Data Exchange (ETDEWEB)

Nefedov, N [Nokia Research Center, Hardturmstrasse 253, CH-8005 Zurich (Switzerland); Swiss Federal Institute of Technology Zurich (ETHZ), ISI Laboratory, Sternwartstrasse 7, CH-8092 Zuerich (Switzerland)], E-mail: nikolai.nefedov@nokia.com

2009-04-08

In this paper we propose a method to perform tunable spectral sensing using globally inhibitory coupled oscillators. The suggested system may operate in the analog radio frequency (RF) domain without high speed ADC and heavy digital signal processing. Oscillator arrays may be made of imprecise elements such as nanoresonators. Provided there is a proper coupling, the system dynamics can be made stable despite the imprecision of the components. Global coupling could be implemented using a common load and controlled by digital means to tune the bandwidth. This method may be used for spectral sensing in cognitive radio terminals.

Modular coupling of transport and chemistry: theory and model applications

International Nuclear Information System (INIS)

Pfingsten, W.

1994-06-01

For the description of complex processes in the near-field of a radioactive waste repository, the coupling of transport and chemistry is necessary. A reason for the relatively minor use of coupled codes in this area is the high amount of computer time and storage capacity necessary for calculations by conventional codes, and lack of available data. The simple application of the sequentially coupled code MCOTAC, which couples one-dimensional advective, dispersive and diffusive transport with chemical equilibrium complexation and precipitation/dissolution reactions in a porous medium, shows some promising features with respect to applicability to relevant problems. Transport, described by a random walk of multi-species particles, and chemical equilibrium calculations are solved separately, coupled only by an exchange term to ensure mass conservation. The modular-structured code was applied to three problems: a) incongruent dissolution of hydrated silicate gels, b) dissolution of portlandite and c) calcite dissolution and hypothetical dolomite precipitation. This allows for a comparison with other codes and their applications. The incongruent dissolution of cement phases, important for degradation of cementitious materials in a repository, can be included in the model without the problems which occur with a directly coupled code. The handling of a sharp multi-mineral front system showed a much faster calculation time compared to a directly coupled code application. Altogether, the results are in good agreement with other code calculations. Hence, the chosen modular concept of MCOTAC is more open to an easy extension of the code to include additional processes like sorption, kinetically controlled processes, transport in two or three spatial dimensions, and adaptation to new developments in computing (hardware and software), an important factor for applicability. (author) figs., tabs., refs

Current Status of Research Activities Related to THM-Coupled Processes in Buffer

International Nuclear Information System (INIS)

Choi, Heui Joo; Lee, Changsoo; Choi, Young Chul; Lee, Minsoo; Kim, Jin Seop

2015-01-01

For the purpose of enhancing the understanding of THM-coupled behavior in and around buffer, a computer code, KAERI-SIMULATOR, is being developed and verified by participating in Decovalex-2015 project. The THM data collected from this facility will be used to validate the KAERI-SIMULATOR

Current Status of Research Activities Related to THM-Coupled Processes in Buffer

Energy Technology Data Exchange (ETDEWEB)

Choi, Heui Joo; Lee, Changsoo; Choi, Young Chul; Lee, Minsoo; Kim, Jin Seop [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-05-15

For the purpose of enhancing the understanding of THM-coupled behavior in and around buffer, a computer code, KAERI-SIMULATOR, is being developed and verified by participating in Decovalex-2015 project. The THM data collected from this facility will be used to validate the KAERI-SIMULATOR.

MEMS Coupled Resonator for Filter Application in Air

KAUST Repository

Ilyas, Saad; Jaber, Nizar; Younis, Mohammad I.

2017-01-01

We present a mechanically coupled MEMS H resonator capable of performing simultaneous amplification and filter operation in air. The device comprises of two doubly clamped polyimide microbeams joined through the middle by a coupling beam of the same size. The resonator is fabricated via a multilayer surface micromachining process. A special fabrication process and device design is employed to enable the device's operation in air and to achieve mechanical amplification of the output response. Moreover, mixed-frequency excitation is used to demonstrate a tunable wide band filter. The device design combined with the mixed-frequency excitation is used to demonstrate simultaneous amplification and filtering in air.

MEMS Coupled Resonator for Filter Application in Air

KAUST Repository

Ilyas, Saad

2017-11-03

We present a mechanically coupled MEMS H resonator capable of performing simultaneous amplification and filter operation in air. The device comprises of two doubly clamped polyimide microbeams joined through the middle by a coupling beam of the same size. The resonator is fabricated via a multilayer surface micromachining process. A special fabrication process and device design is employed to enable the device\\'s operation in air and to achieve mechanical amplification of the output response. Moreover, mixed-frequency excitation is used to demonstrate a tunable wide band filter. The device design combined with the mixed-frequency excitation is used to demonstrate simultaneous amplification and filtering in air.

Full-length mRNA sequencing uncovers a widespread coupling between transcription initiation and mRNA processing.

Science.gov (United States)

Anvar, Seyed Yahya; Allard, Guy; Tseng, Elizabeth; Sheynkman, Gloria M; de Klerk, Eleonora; Vermaat, Martijn; Yin, Raymund H; Johansson, Hans E; Ariyurek, Yavuz; den Dunnen, Johan T; Turner, Stephen W; 't Hoen, Peter A C

2018-03-29

The multifaceted control of gene expression requires tight coordination of regulatory mechanisms at transcriptional and post-transcriptional level. Here, we studied the interdependence of transcription initiation, splicing and polyadenylation events on single mRNA molecules by full-length mRNA sequencing. In MCF-7 breast cancer cells, we find 2700 genes with interdependent alternative transcription initiation, splicing and polyadenylation events, both in proximal and distant parts of mRNA molecules, including examples of coupling between transcription start sites and polyadenylation sites. The analysis of three human primary tissues (brain, heart and liver) reveals similar patterns of interdependency between transcription initiation and mRNA processing events. We predict thousands of novel open reading frames from full-length mRNA sequences and obtained evidence for their translation by shotgun proteomics. The mapping database rescues 358 previously unassigned peptides and improves the assignment of others. By recognizing sample-specific amino-acid changes and novel splicing patterns, full-length mRNA sequencing improves proteogenomics analysis of MCF-7 cells. Our findings demonstrate that our understanding of transcriptome complexity is far from complete and provides a basis to reveal largely unresolved mechanisms that coordinate transcription initiation and mRNA processing.

How couples choose vasectomy.

Science.gov (United States)

Schehl, M

1997-01-01

A study conducted by AVSC International between 1992 and 1995 found that couples around the world go through a highly similar decision-making process when they choose vasectomy as their family planning methods. Study findings are based upon in-depth, qualitative interviews with couples using vasectomy in Bangladesh, Mexico, Kenya, and Rwanda, where the prevalence of vasectomy is relatively low, and Sri Lanka and the US, where it is relatively high. 218 separate interviews were conducted with male and female partners. Concerns about the woman's health were cited by respondents in each country as reasons to cease childbearing and to opt for vasectomy as the means to achieving that end. Also, almost all respondents mentioned varying degrees of financial hardship as contributing to their decision to end childbearing. These findings highlight the concept of partnership in relationships and family planning decision-making, and demonstrate the importance of going beyond traditional stereotypes about gender roles in decision-making. Social influences and the potential risks of using other forms of contraception also contributed to the choice of using vasectomy. The decision-making process and lessons learned are discussed.

Coupled THM processes in EDZ of crystalline rocks using an elasto-plastic cellular automaton

Science.gov (United States)

Pan, Peng-Zhi; Feng, Xia-Ting; Huang, Xiao-Hua; Cui, Qiang; Zhou, Hui

2009-05-01

This paper aims at a numerical study of coupled thermal, hydrological and mechanical processes in the excavation disturbed zones (EDZ) around nuclear waste emplacement drifts in fractured crystalline rocks. The study was conducted for two model domains close to an emplacement tunnel; (1) a near-field domain and (2) a smaller wall-block domain. Goodman element and weak element were used to represent the fractures in the rock mass and the rock matrix was represented as elasto-visco-plastic material. Mohr-Coulomb criterion and a non-associated plastic flow rule were adopted to consider the viscoplastic deformation in the EDZ. A relation between volumetric strain and permeability was established. Using a self-developed EPCA2D code, the elastic, elasto-plastic and creep analyses to study the evolution of stress and deformations, as well as failure and permeability evolution in the EDZ were conducted. Results indicate a strong impact of fractures, plastic deformation and time effects on the behavior of EDZ especially the evolution of permeability around the drift.

An evaluation of reactor cooling and coupled hydrogen production processes using the modular helium reactor

International Nuclear Information System (INIS)

Harvego, E.A.; Reza, S.M.M.; Richards, M.; Shenoy, A.

2006-01-01

The high-temperature characteristics of the modular helium reactor (MHR) make it a strong candidate for producing hydrogen using either thermochemical or high-temperature electrolysis (HTE) processes. Using heat from the MHR to drive a sulfur-iodine (SI) thermochemical hydrogen production process has been the subject of a U.S. Department of Energy sponsored Nuclear Engineering Research Initiative (NERI) project led by General Atomics, with participation from the Idaho National Laboratory (INL) and Texas A and M University. While the focus of much of the initial work was on the SI thermochemical production of hydrogen, recent activities included development of a preconceptual design for an integral HTE hydrogen production plant driven by the process heat and electricity produced by a 600 MW MHR. This paper describes ATHENA analyses performed to evaluate alternative primary system cooling configurations for the MHR to minimize peak reactor vessel and core temperatures while achieving core helium outlet temperatures in the range of 900-1000 deg. C that are needed for the efficient production of hydrogen using either the SI or HTE process. The cooling schemes investigated are intended to ensure peak fuel temperatures do not exceed specified limits under normal or transient upset conditions, and that reactor vessel temperatures do not exceed American Society of Mechanical Engineers (ASME) code limits for steady-state or transient conditions using standard light water reactor vessel materials. Preconceptual designs for SI and HTE hydrogen production plants driven by one or more 600 MW MHRs at helium outlet temperatures in the range of 900-1000 deg. C are described and compared. An initial SAPHIRE model to evaluate the reliability, maintainability, and availability of the SI hydrogen production plant is also described. Finally, a preliminary flowsheet for a conceptual design of an HTE hydrogen production plant coupled to a 600 MW modular helium reactor is presented and

Antiresonance and decoupling in electronic transport through parallel-coupled quantum-dot structures with laterally-coupled Majorana zero modes

Science.gov (United States)

Zhang, Ya-Jing; Zhang, Lian-Lian; Jiang, Cui; Gong, Wei-Jiang

2018-02-01

We theoretically investigate the electronic transport through a parallel-coupled multi-quantum-dot system, in which the terminal dots of a one-dimensional quantum-dot chain are embodied in the two arms of an Aharonov-Bohm interferometer. It is found that in the structures of odd(even) dots, all their even(odd) molecular states have opportunities to decouple from the leads, and in this process antiresonance occurs which are accordant with the odd(even)-numbered eigenenergies of the sub-molecule without terminal dots. Next when Majorana zero modes are introduced to couple laterally to the terminal dots, the antiresonance and decoupling phenomena still co-exist in the quantum transport process. Such a result can be helpful in understanding the special influence of Majorana zero mode on the electronic transport through quantum-dot systems.

Thermal Phenomena in the Friction Process of the TG15 - Hard Anodic Coating Couple

Directory of Open Access Journals (Sweden)

Służałek G.

2016-09-01

Full Text Available The paper presents a one-dimensional model of heat conduction in a couple consisting of a cylinder made of a sliding plastic material, TG15, and a cuboid made of alloy AW 6061 coated with a hard anodic coating, where the couple is heated with the heat generated during friction. TG15 is a composite material based on polytetrafluoroethylene (PTFE with a 15% graphite filler, used for piston rings in oil-free air-compressors. Measurement of temperature in the friction zone is extremely important for the understanding and analysis of the phenomena occurring therein. It is practically impossible to introduce a temperature sensor in such a place. Therefore, the interaction taking place in such a couple was modelled using numerical methods. In order to simplify and accelerate the calculations, a one-dimensional model and constant thermophysical parameters of the materials participating in friction were adopted. To solve the proposed model, the finite difference method was used (FDM. The resultant system of equations was solved by means of an explicit scheme.

Cascading failure of interdependent networks with different coupling preference under targeted attack

International Nuclear Information System (INIS)

Chen, Zhen; Du, Wen-Bo; Cao, Xian-Bin; Zhou, Xing-Lian

2015-01-01

Cascading failure is one of the most central topics in the field of complex networks. In this paper, the cascading failure model is extended to the case of interdependent networks, and the effect of coupling preference on systems robustness is intensively investigated. It is found that the performance of coupling preference on robustness is dependent on coupling probability. Disassortative coupling is more robust for sparse coupling while assortative coupling performs better for dense coupling. We provide an explanation for this constructive phenomenon via examining cascading process from the microscopic point of view. Our work can be useful to the design and optimization of interdependent networked systems.

Numerical Investigation of Simultaneously Deposition and Re-Entrainment Fouling Processes in Corrugated Tubes by Coupling CFD and DEM

DEFF Research Database (Denmark)

Hærvig, Jakob; Condra, Thomas Joseph; Sørensen, Kim

Computational Fluid Dynamics (CFD) software OpenFOAM is coupled to the Discrete Element Method (DEM) software LIGGGHTS using the coupling software CFDEM. A four-way coupling is used to model fluid-particle and particle-particle interactions and thereby allowing for a particle fouling layer to build up along...

Spin-orbit-coupled Bose-Einstein condensates of rotating polar molecules

Science.gov (United States)

Deng, Y.; You, L.; Yi, S.

2018-05-01

An experimental proposal for realizing spin-orbit (SO) coupling of pseudospin 1 in the ground manifold 1Σ (υ =0 ) of (bosonic) bialkali polar molecules is presented. The three spin components are composed of the ground rotational state and two substates from the first excited rotational level. Using hyperfine resolved Raman processes through two select excited states resonantly coupled by a microwave, an effective coupling between the spin tensor and linear momentum is realized. The properties of Bose-Einstein condensates for such SO-coupled molecules exhibiting dipolar interactions are further explored. In addition to the SO-coupling-induced stripe structures, the singly and doubly quantized vortex phases are found to appear, implicating exciting opportunities for exploring novel quantum physics using SO-coupled rotating polar molecules with dipolar interactions.

If We Build It, They Will Come: Exploring Policy and Practice Implications of Public Support for Couple and Relationship Education for Lower Income and Relationally Distressed Couples.

Science.gov (United States)

Bradford, Angela B; Hawkins, Alan J; Acker, Jennifer

2015-12-01

Over the past decade, public funding for Couple and Relationship Education programs has expanded. As program administrators have been able to extend their reach to low-income individuals and couples using this support, it has become apparent that greater numbers of relationally distressed couples are attending classes than previously anticipated. Because psychoeducational programs for couples have traditionally served less distressed couples, this dynamic highlights the need to examine the policy and practice implications of more distressed couples accessing these services. This paper reviews some of the most immediate issues, including screening for domestic violence and couple needs, pedagogical considerations, and the potential integration of therapy and education services. We also make suggestions for future research that can inform policy and practice efforts. © 2015 Family Process Institute.

Thermal-hydraulic-geochemical coupled processes around disposed high level nuclear waste in deep granite hosted geological repositories: frontier areas of advanced groundwater research in India

International Nuclear Information System (INIS)

Bajpai, R.K.

2012-01-01

Indian policy for permanent disposal of high level nuclear wastes with radionuclide having very long half lives include their immobilization in a stable matrix i.e. glasses of suitable composition, its storage in high integrity steel canisters and subsequent disposal in suitable host rock like granites at a depth of 400-500m in stable geological set up. The site for such disposal facilities are selected after vigorous assessment of their stability implying an exhaustive site selection methodology based on a large number of criteria and attributes. In India, an area of about 70000 square kilometers occupied by granites has been subjected to such evaluation for generating comprehensive database on host rock parameters. The sites selected after such intensive analysis are expected to remain immune to processes like seismicity, volcanism, faulting, uplift, erosion, flooding etc. even in distant future spanning over tens of thousands of years. Nevertheless, groundwater has emerged as the only credible pathway through which disposed waste can eventually find its way to accessible biosphere. Hence groundwater research constitutes one of the most important aspects in demonstration of safety of such disposal. The disposed waste due to continuous emission of decay heat creates high temperature field around them with resultant increase in groundwater temperature in the vicinity. Hot groundwater on reacting with steel canisters, backfill clays and cement used around the disposed canister, produces geochemical environment characterized by altered Ph, Eh and groundwater compositions. Acceleration in geochemical interaction among waste-groundwater-clay-cement-granite often results in dissolution or precipitation reactions along the groundwater flow paths i.e. fractures with resultant increase or decrease in their permeability. Thus thermal, hydraulic and geochemical processes work interdependently around the disposed waste. These coupled processes also control the release and

Quantum process tomography with informational incomplete data of two J-coupled heterogeneous spins relaxation in a time window much greater than T1

Science.gov (United States)

Maciel, Thiago O.; Vianna, Reinaldo O.; Sarthour, Roberto S.; Oliveira, Ivan S.

2015-11-01

We reconstruct the time dependent quantum map corresponding to the relaxation process of a two-spin system in liquid-state NMR at room temperature. By means of quantum tomography techniques that handle informational incomplete data, we show how to properly post-process and normalize the measurements data for the simulation of quantum information processing, overcoming the unknown number of molecules prepared in a non-equilibrium magnetization state (Nj) by an initial sequence of radiofrequency pulses. From the reconstructed quantum map, we infer both longitudinal (T1) and transversal (T2) relaxation times, and introduce the J-coupling relaxation times ({T}1J,{T}2J), which are relevant for quantum information processing simulations. We show that the map associated to the relaxation process cannot be assumed approximated unital and trace-preserving for times greater than {T}2J.

Coupling a Basin Modeling and a Seismic Code using MOAB

KAUST Repository

Yan, Mi; Jordan, Kirk; Kaushik, Dinesh; Perrone, Michael; Sachdeva, Vipin; Tautges, Timothy J.; Magerlein, John

2012-01-01

We report on a demonstration of loose multiphysics coupling between a basin modeling code and a seismic code running on a large parallel machine. Multiphysics coupling, which is one critical capability for a high performance computing (HPC) framework, was implemented using the MOAB open-source mesh and field database. MOAB provides for code coupling by storing mesh data and input and output field data for the coupled analysis codes and interpolating the field values between different meshes used by the coupled codes. We found it straightforward to use MOAB to couple the PBSM basin modeling code and the FWI3D seismic code on an IBM Blue Gene/P system. We describe how the coupling was implemented and present benchmarking results for up to 8 racks of Blue Gene/P with 8192 nodes and MPI processes. The coupling code is fast compared to the analysis codes and it scales well up to at least 8192 nodes, indicating that a mesh and field database is an efficient way to implement loose multiphysics coupling for large parallel machines.

Coupling a Basin Modeling and a Seismic Code using MOAB

KAUST Repository

Yan, Mi

2012-06-02

We report on a demonstration of loose multiphysics coupling between a basin modeling code and a seismic code running on a large parallel machine. Multiphysics coupling, which is one critical capability for a high performance computing (HPC) framework, was implemented using the MOAB open-source mesh and field database. MOAB provides for code coupling by storing mesh data and input and output field data for the coupled analysis codes and interpolating the field values between different meshes used by the coupled codes. We found it straightforward to use MOAB to couple the PBSM basin modeling code and the FWI3D seismic code on an IBM Blue Gene/P system. We describe how the coupling was implemented and present benchmarking results for up to 8 racks of Blue Gene/P with 8192 nodes and MPI processes. The coupling code is fast compared to the analysis codes and it scales well up to at least 8192 nodes, indicating that a mesh and field database is an efficient way to implement loose multiphysics coupling for large parallel machines.

Neuron-glia metabolic coupling and plasticity.

Science.gov (United States)

Magistretti, Pierre J

2006-06-01

The coupling between synaptic activity and glucose utilization (neurometabolic coupling) is a central physiological principle of brain function that has provided the basis for 2-deoxyglucose-based functional imaging with positron emission tomography (PET). Astrocytes play a central role in neurometabolic coupling, and the basic mechanism involves glutamate-stimulated aerobic glycolysis; the sodium-coupled reuptake of glutamate by astrocytes and the ensuing activation of the Na-K-ATPase triggers glucose uptake and processing via glycolysis, resulting in the release of lactate from astrocytes. Lactate can then contribute to the activity-dependent fuelling of the neuronal energy demands associated with synaptic transmission. An operational model, the 'astrocyte-neuron lactate shuttle', is supported experimentally by a large body of evidence, which provides a molecular and cellular basis for interpreting data obtained from functional brain imaging studies. In addition, this neuron-glia metabolic coupling undergoes plastic adaptations in parallel with adaptive mechanisms that characterize synaptic plasticity. Thus, distinct subregions of the hippocampus are metabolically active at different time points during spatial learning tasks, suggesting that a type of metabolic plasticity, involving by definition neuron-glia coupling, occurs during learning. In addition, marked variations in the expression of genes involved in glial glycogen metabolism are observed during the sleep-wake cycle, with in particular a marked induction of expression of the gene encoding for protein targeting to glycogen (PTG) following sleep deprivation. These data suggest that glial metabolic plasticity is likely to be concomitant with synaptic plasticity.

Emotional Stroop interference for threatening words is related to reduced EEG δ-β coupling and low attentional control.

Science.gov (United States)

Putman, Peter; Arias-Garcia, Elsa; Pantazi, Ioanna; van Schie, Charlotte

2012-05-01

Previously, electroencephalographic (EEG) delta-beta coupling (positive correlation between power in the fast beta and slow delta frequency bands) has been related to affective processing. For instance, differences in delta-beta coupling have been observed between people in a psychological stress condition and controls. We previously reported relationships between attentional threat processing and delta-beta coupling and individual differences in attentional control. The present study extended and replicated these findings in a large mixed gender sample (N=80). Results demonstrated that emotional Stroop task interference for threatening words was related to self-reported attentional inhibition capacity and frontal delta-beta coupling. There was no clear gender difference for delta-beta coupling (only a non-significant trend) and the relationship between delta-beta coupling and attentional threat-processing was not affected by gender. These results replicate and extend an earlier finding concerning delta-beta coupling and cognitive affect regulation and further clarify relationships between delta-beta coupling, attentional control, and threat-processing. Copyright © 2012 Elsevier B.V. All rights reserved.

Attachment Versus Differentiation: The Contemporary Couple Therapy Debate.

Science.gov (United States)