An Alternative Low-Cost Process for Deposition of MCrAlY Bond Coats for Advanced Syngas/Hydrogen Turbine Applications

Energy Technology Data Exchange (ETDEWEB)

Zhang, Ying [Tennessee Technological Univ., Cookeville, TN (United States)

2015-09-11

The objective of this project was to develop and optimize MCrAlY bond coats for syngas/hydrogen turbine applications using a low-cost electrolytic codeposition process. Prealloyed CrAlY-based powders were codeposited into a metal matrix of Ni, Co or Ni-Co during the electroplating process, and a subsequent post-deposition heat treatment converted it to the MCrAlY coating. Our research efforts focused on: (1) investigation of the effects of electro-codeposition configuration and parameters on the CrAlY particle incorporation in the NiCo-CrAlY composite coatings; (2) development of the post-deposition heat treating procedure; (3) characterization of coating properties and evaluation of coating oxidation performance; (4) exploration of a sulfurfree electroplating solution; (5) cost analysis of the present electrolytic codeposition process. Different electro-codeposition configurations were investigated, and the rotating barrel system demonstrated the capability of depositing NiCo-CrAlY composite coatings uniformly on the entire specimen surface, with the CrAlY particle incorporation in the range 37-42 vol.%. Post-deposition heat treatment at 1000-1200 °C promoted interdiffusion between the CrAlY particles and the Ni-Co metal matrix, resulting in β/γ’/γ or β/γ’ phases in the heat-treated coatings. The results also indicate that the post-deposition heat treatment should be conducted at temperatures ≤1100 °C to minimize Cr evaporation and outward diffusion of Ti. The electro-codeposited NiCrAlY coatings in general showed lower hardness and surface roughness than thermal spray MCrAlY coatings. Coating oxidation performance was evaluated at 1000-1100 °C in dry and wet air environments. The initial electro-codeposited NiCoCrAlY coatings containing relatively high sulfur did not show good oxidation resistance. After modifications of the coating process, the cleaner NiCoCrAlY coating exhibited good oxidation performance at 1000 °C during the 2,000 1-h cyclic

Thermo-mechanical treatment of low-cost alloy Ti-4.5Al-6.9Cr-2.3Mn and microstructure and mechanical characteristics

Science.gov (United States)

Chen, Guangyao; Kang, Juyun; Wang, Shusen; Wang, Shihua; Lu, Xionggang; Li, Chonghe

2018-04-01

In this study, the thermo-mechanical treatment process for low-cost Ti-4.5Al-6.9Cr-2.3Mn alloy were designed on the basis of assessment of Ti-Al-Cr-Mn thermodynamic system. The microstructure and mechanical properties of Ti-4.5Al-6.9Cr-2.3Mn forging and sheet were investigated by using the OM, SEM and universal tensile testing machine. The results show that both the forging and sheet were consisted of α + β phase, which is consistent with the expectation, and no element Cr and Mn existed in the grain boundaries of the sheet after quenching, and the C14 laves phase was not detected. The average ultimate tensile strength (σ b), 0.2% proof strength (σ 0.2) and elongation (EI) of alloy sheet after quenching can reach 1059 MPa, 1051 MPa and 24.6 Pct., respectively. Moreover, the average ultimate tensile strength of Ti-4.5Al-6.9Cr-2.3Mn forgings can reach 1599 MPa and the average elongation can reach 11.2 Pct., and a more excellent property of Ti-4.5Al-6.9Cr-2.3Mn forging is achieved than that of TC4 forging. It provides a theoretical support for further developing this low-cost alloy.

Innovación y ruptura en la métrica de la poesía en al-Maqāmāt al-Luzūmiyya de al-Saraqusṭī (s. VI/XII

Directory of Open Access Journals (Sweden)

Ferrando, Ignacio

2016-06-01

Full Text Available Al-Maqāmāt al-Luzūmiyya, a collection of 50 picaresque-like stories couched in rhymed prose by Abū l-Ṭāhir al-Saraqusṭī in al-Andalus in the VI/XIIth century, were considered by Western scholars, up until the eighties of XXth century, as highly rhetorical pieces with a negligible and irrelevant content. However, some contemporary scholars argued that they contain some degree of social and political criticism, as they constitute a fictional domain in which subversion and irony play a fundamental role. In this paper, we cast some light on the particular use of metrical patterns in Al-Maqāmāt al-Luzūmiyya, which should be considered another subversion field: a poetical rhythm that avoids the most usual Arabic metrical patterns, contributing to provide the maqāma a flavor of the countergenre.Al-Maqāmāt al-Luzūmiyya, la colección de 50 relatos de corte picaresco escritos en una exigente prosa rimada por Abū l-Ṭāhir al-Saraqusṭī en al-Andalus en el siglo VI/XII, han sido consideradas por los críticos occidentales como piezas de alta retórica y de virtuosismo lingüístico en las que el contenido es prácticamente irrelevante. Sin embargo, a partir de los años 80 del siglo pasado, algunos investigadores han tratado de incidir en el hecho de que esta obra contiene cierto grado de crítica social y política, puesto que constituye un espacio ficticio en el que la subversión y la ironía desempeñan un papel fundamental. En este trabajo vamos a tratar de arrojar luz sobre el uso particular de los esquemas métricos por parte de al-Saraqusṭī, tratando de mostrar que los metros constituyen otro más de los ámbitos de subversión tan caros al autor. De hecho, el uso de ritmos “invertidos” o contrarios a los más habituales de la poesía clásica contribuye a darle a la maqāma ese aire de anti género que la puebla.

Información, señal, comunidad y contexto: su importancia al tratar con sistemas adaptativos complejos

Directory of Open Access Journals (Sweden)

Jordi Guzman

2007-07-01

Full Text Available El artículo trata de las diferencias entre información y conocimiento, así como de la relevancia del contexto en el aprendizaje, el cual se da dentro de una cultura en competencia por su supervivencia con otras culturas. Estas características definen un sistema adaptativo complejo, que se asemeja a la conducta de las especies que luchan por sobrevivir a los cambios de un entorno en continuo movimiento.

Incubadoras de empresas, creación de empresas y redes sociales

OpenAIRE

Bravo García, Saulo

2013-01-01

En esta investigación se tratarán de analizar aspectos de teorías relevantes que han contribuido al conocimiento sobre incubadoras de empresas. En ese sentido, este trabajo busca entender cómo una incubadora de empresas puede convertirse en un vínculo est En esta investigación se tratarán de analizar aspectos de teorías relevantes que han contribuido al conocimiento sobre incubadoras de empresas. En ese sentido, este trabajo busca entender cómo una incubadora de empresas puede convertirse ...

What Costs Do Reveal and Moving beyond the Cost Debate: Reply to Einstein and McDaniel (2010)

Science.gov (United States)

Smith, Rebekah E.

2010-01-01

Einstein et al. (2005) predicted no cost to an ongoing task when a prospective memory task met certain criteria. Smith, Hunt, McVay, and McConnell (2007) used prospective memory tasks that met these criteria and found a cost to the ongoing task, contrary to Einstein et al.'s prediction. Einstein and McDaniel (2010) correctly noted that there are…

Self-standing silicon-carbon nanotube/graphene by a scalable in situ approach from low-cost Al-Si alloy powder for lithium ion batteries

Science.gov (United States)

Cai, Hongyan; Han, Kai; Jiang, Heng; Wang, Jingwen; Liu, Hui

2017-10-01

Silicon/carbon (Si/C) composite shows great potential to replace graphite as lithium-ion battery (LIB) anode owing to its high theoretical capacity. Exploring low-cost scalable approach for synthesizing Si/C composites with excellent electrochemical performance is critical for practical application of Si/C anodes. In this study, we rationally applied a scalable in situ approach to produce Si-carbon nanotube (Si-CNT) composite via acid etching of commercial inexpensive micro-sized Al-Si alloy powder and CNT mixture. In the Si-CNT composite, ∼10 nm Si particles were uniformly deposited on the CNT surface. After combining with graphene sheets, a flexible self-standing Si-CNT/graphene paper was fabricated with three-dimensional (3D) sandwich-like structure. The in situ presence of CNT during acid-etching process shows remarkable two advantages: providing deposition sites for Si atoms to restrain agglomeration of Si nanoparticles after Al removal from Al-Si alloy powder, increasing the cross-layer conductivity of the paper anode to provide excellent conductive contact sites for each Si nanoparticles. When used as binder-free anode for LIBs without any further treatment, in situ addition of CNT especially plays important role to improve the initial electrochemical activity of Si nanoparticles synthesized from low-cost Al-Si alloy powder, thus resulting in about twice higher capacity than Si/G paper anode. The self-standing Si-CNT/graphene paper anode exhibited a high specific capacity of 1100 mAh g-1 even after 100 cycles at 200 mA g-1 current density with a Coulombic efficiency of >99%. It also showed remarkable rate capability improvement compared to Si/G paper without CNT. The present work demonstrates a low-cost scalable in situ approach from commercial micro-sized Al-Si alloy powder for Si-based composites with specific nanostructure. The Si-CNT/graphene paper is a promising anode candidate with high capacity and cycling stability for LIBs, especially for the

An Al-doped ZnO electrode grown by highly efficient cylindrical rotating magnetron sputtering for low cost organic photovoltaics

Science.gov (United States)

Park, Jun-Hyuk; Ahn, Kyung-Jun; Park, Kang-Il; Na, Seok-In; Kim, Han-Ki

2010-03-01

We report the characteristics of Al-doped zinc oxide (AZO) films prepared by a highly efficient cylindrical rotating magnetron sputtering (CRMS) system for use as a transparent conducting electrode in cost-efficient bulk hetero-junction organic solar cells (OSCs). Using a rotating cylindrical type cathode with an AZO target, whose usage was above 80%, we were able to obtain a low cost and indium free AZO electrode with a low sheet resistance of ~4.59 Ω/sq, a high transparency of 85% in the visible wavelength region and a work function of 4.9 eV at a substrate temperature of 230 °C. Moreover, the neutral poly(3,4-ethylenedioxythiophene) : poly(styrenesulfonate) based OSC fabricated on the CRMS-grown AZO electrode at 230 °C showed an open circuit voltage of 0.5 V, a short circuit current of 8.94 mA cm-2, a fill factor of 45% and power conversion efficiency of 2.01%, indicating that CRMS is a promising cost-efficient AZO deposition technique for low cost OSCs.

Hipotiroidismo Subclínico ¿Cuándo Tratar?

Directory of Open Access Journals (Sweden)

Alfredo Jácome Roca

2007-12-01

Nadie pensaba además en hacer tamizajes con metabolismos basales o yodoproteinemias (PBI en la población general o –ni siquiera- en grupos etáreos especiales como embarazadas y menopáusicas, menos sabiendo que los estrógenos alteraban las pruebas, por su acción sobre las proteínas transportadoras de hormonas tiroideas. En menopáusicas viudas, era seguro encontrar una PBI alta, porque el vestido negro acostumbrado en los largos lutos contenía yodo que alteraba esta prueba (2. A menudo escuchábamos presentaciones en congresos médicos sobre el “Uso y abuso de las hormonas tiroideas”, en las que usualmente se criticaba su extendido uso en una variada patología; muchos clínicos eran aficionados a utilizar los preparados de la época –tiroides desecado, tiroglobulina, triyodotironina, y al final el liotirox- a pesar de que no hubiese estudios que demostraran su utilidad de manera fehaciente, o que se albergaran ciertos temores sobre sus efectos deletéreos: la osteoporosis no estaba de moda, y la fibrilación auricular era problema de los cardiólogos (3.

Factores de riesgo de bajo peso al nacer en un hospital cubano, 1997-2000

Directory of Open Access Journals (Sweden)

Escobar José Andrés Cabrales

2002-01-01

Full Text Available Objetivo. Identificar qué factores de riesgo materno durante el embarazo se asocian a la incidencia de bajo peso al nacer (menos de 2 500 g. Métodos. Se diseñó un estudio de casos y testigos con 764 casos de nacimiento simple con un peso al nacer de menos de 2 500 g, y 1 437 testigos del Hospital Gineco-Obstétrico Provincial de Sancti Spíritus, Cuba, durante el cuatrienio de 1997-2000. Los datos se obtuvieron de historias clínicas, registros de partos y entrevistas personales con las madres. Se realizó un análisis con dos variables y se controlaron los posibles factores de confusión mediante regresión logística dicotómica con el programa SPSS. Se usó un modelo final de múltiples variables para identificar los factores de riesgo maternos asociados con el bajo peso al nacer. Resultados. El análisis con múltiples variables mostró una asociación significativa del bajo peso al nacer con la presencia de anemia en la madre cuando se detectó el embarazo, la sepsis urinaria durante el embarazo, el asma bronquial, un aumento de peso materno menor de 8 kg durante todo el embarazo, el hábito de fumar durante el mismo, antecedentes de bajo peso al nacer en partos anteriores, la presencia de hipertensión arterial desde antes de la gestación y la consulta prenatal extemporánea. Conclusiones. A partir de estos resultados se concluyó que, independientemente de la medida de impacto utilizada, es importante tratar de disminuir los factores de riesgo identificados a fin de reducir la incidencia del bajo peso al nacer en la provincia de Sancti Spíritus.

Factores de riesgo de bajo peso al nacer en un hospital cubano, 1997-2000

Directory of Open Access Journals (Sweden)

José Andrés Cabrales Escobar

2002-09-01

Full Text Available Objetivo. Identificar qué factores de riesgo materno durante el embarazo se asocian a la incidencia de bajo peso al nacer (menos de 2 500 g. Métodos. Se diseñó un estudio de casos y testigos con 764 casos de nacimiento simple con un peso al nacer de menos de 2 500 g, y 1 437 testigos del Hospital Gineco-Obstétrico Provincial de Sancti Spíritus, Cuba, durante el cuatrienio de 1997-2000. Los datos se obtuvieron de historias clínicas, registros de partos y entrevistas personales con las madres. Se realizó un análisis con dos variables y se controlaron los posibles factores de confusión mediante regresión logística dicotómica con el programa SPSS. Se usó un modelo final de múltiples variables para identificar los factores de riesgo maternos asociados con el bajo peso al nacer. Resultados. El análisis con múltiples variables mostró una asociación significativa del bajo peso al nacer con la presencia de anemia en la madre cuando se detectó el embarazo, la sepsis urinaria durante el embarazo, el asma bronquial, un aumento de peso materno menor de 8 kg durante todo el embarazo, el hábito de fumar durante el mismo, antecedentes de bajo peso al nacer en partos anteriores, la presencia de hipertensión arterial desde antes de la gestación y la consulta prenatal extemporánea. Conclusiones. A partir de estos resultados se concluyó que, independientemente de la medida de impacto utilizada, es importante tratar de disminuir los factores de riesgo identificados a fin de reducir la incidencia del bajo peso al nacer en la provincia de Sancti Spíritus.

Las indicaciones geográficas en el TLC firmado por Colombia y Perú con EUA frente al TLC con Chile.

Directory of Open Access Journals (Sweden)

Juan Andrés Zarama Medina

2007-06-01

Full Text Available El propósito de este trabajo es hacer un análisis crítico del tratamiento que se ha dado a las Indicaciones Geográficas y mas específicamente a las Denominaciones de Origen en el Tratado de Libre Comercio que firmaron recientemente por Colombia y Perú, con los Estados Unidos (TLC, al que en adelante denominaremos TLC CAN, y compararlo con el TLC firmado con Chile (En adelante TLC CHILE. Para efectos de este trabajo, centraremos nuestra atención de manera específica en la tendencia de estos tratados a tratar las indicaciones geográficas y en especial las denominaciones de origen, como marcas colectivas y de certificación o garantía.

Coste-efectividad de la adición de acarbosa al tratamiento de pacientes con diabetes tipo 2 en España

OpenAIRE

Piñol, Carme; Roze, Stephane; Valentine, William; Evers, Thomas

2007-01-01

Objetivos: Evaluar el coste-efectividad de la adición de acarbosa al tratamiento de pacientes con diabetes mellitus tipo 2 (DM2) en España. Métodos: Se utilizó el CORE Diabetes Model (modelo de simulación informática publicado y validado) para proyectar a largo plazo los resultados clínicos y de costes de la DM2. Las probabilidades de transición y los riesgos se obtuvieron de distintas publicaciones. Los efectos del tratamiento y las características basales de la cohorte se obtuvieron de un m...

Preparación de informes contables ambientales

OpenAIRE

García Casella, Carlos Luis

2011-01-01

Partiendo de la definición de Contabilidad llegamos a la llamada Contabilidad Ambiental como una rama de la disciplina que necesita tratar varios temas principales. Uno de ellos es el establecimiento de Sistemas Contables Ambientales que produzcan informes Contables Ambientales. A la vez hay que establecer Planes Contables Integrados en el tema ambiental y hay que lograr que los informes contables ambientales incluyan los efectos de los mecanismos de desarrollo limpio. Al tratar el tema de la...

Empresas y Derechos Humanos. O cómo llevar la pedagogía crítica al aula de español como lengua extranjera

Directory of Open Access Journals (Sweden)

Santiago Ospina García

2013-01-01

Full Text Available Este artículo expone un estudio de caso llevado a cabo con estudiantes universitarios del Collège Européen Franco Allemand de Sciences Po París en Nancy basado en la pedagogía crítica. El objetivo principal fue hacer tomar conciencia a los participantes (futuros miembros de empresas y organizaciones europeas e internacionales del irrespeto de Derechos Humanos por parte de algunas corporaciones transnacionales en América Latina. Mediante este estudio también se buscó generar reflexión en los estudiantes y llevarlos a evaluar problemas precisos, tratar de encontrar soluciones y actuar a corto y mediano plazo para aportar una solución. Las conclusiones arrojadas revelan que se puede aprender español de manera crítica y reflexiva confirmando que la lengua es un medio de acceso tanto a la cultura de los países hispanoamericanos como al desarrollo intelectual y al pensamiento crítico.

«La verdad Oculta» (2015: una disputa médico?deportiva llevada al cine

Directory of Open Access Journals (Sweden)

Alejandro A. PENICHE PÉREZ

2016-12-01

Full Text Available La verdad oculta (2015 de Peter Landesman se trata de un drama deportivo, basado en hechos reales sobre la vida del famoso neuropatólogo forense, Dr. Bennet Omalu; cuyo personaje es interpretado por el actor Will Smith. Esta película narra los acontecimientos que condujeron al Dr. Omalu hacia el descubrimiento de una enfermedad neurodegenerativa progresiva, la cual nombró como Encefalopatía Traumática Crónica (ETC. Ésta enfermedad se manifiesta en los jugadores profesionales de fútbol americano, como consecuencia del constante número de colisiones que reciben los jugadores dentro del campo. Dicho descubrimiento generó disgusto a una de las corporaciones más poderosas y queridas del mundo, la National Football League (NFL situación que la condujo a tratar de desacreditar la información publicada por el Dr. Bennet Omalu, quien decidió correr el riesgo de enfrentarlos para dar a conocer la verdad.

Análisis costo versus efectividad del Etanercept, Infliximab y Adalimumab, en pacientes con artritis reumatoide refractaria

OpenAIRE

Cubillos Mendoza, Luz Marina; Pinto Álvarez, Juliana

2017-01-01

En la actualidad existen varias tecnologías para tratar la artritis reumatoide (AR), lo que se ha convertido en una industria puesto que los tratamientos para la misma, pueden ser por largos periodos de tiempo, con costos importantes para el sistema de salud colombiano. Las instituciones de salud, se enfrentan a un gran reto al tratar de mejorar la calidad de vida de los pacientes a través de nuevas alternativas terapéuticas mediante medicamentos inmunomoduladores como los antagonistas del fa...

Poema: Mithistorema

Directory of Open Access Journals (Sweden)

Jorge Seferis

1966-08-01

Full Text Available Hemos esperado al mensajero tres años, vigilando los pinos, la playa las estrellas. Nos uníamos al hierro del arado o a la quilla del navío para tratar de descubrir el Primer gérmen y que el drama muy antiguo recomenzara.

Experimento sobre Diversas Fórmulas para Tratar las Heridas en los Árboles.

Directory of Open Access Journals (Sweden)

Obregón Botero Rafael

1940-03-01

Full Text Available Sin duda una de las prácticas más delicadas y difíciles con que tropieza el agricultor consciente, es la adecuada y perfecta poda de sus árboles, abundando los diversos sistemas preconizados tanto para árboles frutales como para el café y el cacao. Todos o casi todos los sistemas tienden a abarcar dos puntos principales; la mayor producción en cantidad y calidad aceptable sin debilitamiento de la planta y la búsqueda de economía en su ejecución. Sus principios, normas, implementos, épocas y demás factores varían con la planta y los puntos de vista del preconizador de los diferentes sistemas, pero todos están acordes en cuanto a la necesidad de proteger los cortes hechos durante las prácticas. De la misma manera como los animales están sujetos a adquirir infecciones por las heridas o desgarramientos de su piel, las plantas también lo están por la infección al practicar cortes en sus ramas o simplemente al través de los desperfectos y desgarraduras en sus tejidos protectores, la corteza de las ramas, tallos y raíces.

Facile and Low-Cost Preparation of Nb/Al Oxide Catalyst with High Performance for the Conversion of Kiwifruit Waste Residue to Levulinic Acid

Directory of Open Access Journals (Sweden)

Rui Wang

2015-09-01

Full Text Available The kiwifruit industry is booming worldwide. As a result, a great deal of kiwifruit waste residue (KWR containing monosaccharides is produced and discarded. This material shows great potential for the production of platform chemicals. In this study, a series of Nb/Al oxide catalysts were synthesized via a facile and low-cost coprecipitation method, and their structures were characterized using: thermal gravimetric analysis (TGA, XRD, FESEM, TEM, X-ray photoelectron spectroscopy (XPS, NH3-TPD, N2 adsorption-desorption, and FTIR-Pyridine adsorption. Experimental results of sugar-to-levulinic acid (LA conversion revealed that the 20%Nb/Al oxide catalyst provided the highest catalytic performance and durability in terms of LA yield from fructose (74.2% at 463 K after 10 min and from glucose (47.5% at 473 K after 15 min. Notably, the 20% Nb/Al oxide catalyst with a 10% dosage is capable of converting kiwifruit waste residue to LA at 473 K after 10 min. In conclusion, the enhanced catalytic performance was obtained due to the high acidity, and large surface areaof Nb/Al oxide catalyst.

Ni ética ambiental, ni valores. La reivindicación de Hans Jonas para la ética ambiental hecha por Eric Pommier, considerada desde la crítica de Heidegger al concepto de valor

Directory of Open Access Journals (Sweden)

Richard Ayala-Ardila

2017-01-01

Full Text Available En este trabajo se cuestiona tanto a la ética ambiental como a la filosofía ambiental desde la crítica hecha por Martin Heidegger al concepto de valor; tal cuestionamiento es precedido por una presentación de las consideraciones de Eric Pommier sobre la ética ambiental, lo cual implica tratar su apreciación de la filosofía ambiental norteamericana (Leopold, Rolston III y Callicot, su lectura de la obra de Hans Jonas y su reivindicación de las ideas de este autor para la ética o para la filosofía ambiental. Se mostrará que los problemas fundamentales de la ética ambiental consisten en encontrar una manera de demostrar el valor intrínseco de la naturaleza y en lograr este objetivo sin hacer concesión alguna al dualismo ontológico.

Sensibilidad al benzonidazol de cepas de Trypanosoma cruzi sugiere la circulación de cepas naturalmente resistentes en Colombia

Directory of Open Access Journals (Sweden)

Ana María Mejía-Jaramillo

2012-06-01

Full Text Available Introducción. La enfermedad de Chagas, causada por Trypanosoma cruzi, es uno de los problemas más graves de salud pública en el continente americano. El benzonidazol es uno de los dos medicamentos utilizados para tratar la enfermedad de Chagas. Sin embargo, la variación de la sensibilidad del parásito a este medicamento es una de las principales causas del fracaso del tratamiento. Objetivo. Evaluar la sensibilidad in vitro al benzonidazol de cepas colombianas de T. cruzi de diferentes orígenes y procedencia geográfica. Materiales y métodos. Treinta y tres cepas colombianas de T. cruzi aisladas de humanos, vectores y mamíferos, se analizaron in vitro mediante el micrométodo enzimático de MTT para determinar la concentración inhibitoria 50 (CI50 al benzonidazol. Se estudió la correlación entre la sensibilidad in vitro al medicamento y diferentes parámetros biológicos y eco-epidemiológicos. Resultados. El análisis de sensibilidad al medicamento indicó que el 36 % de las cepas eran sensibles, el 48 %, parcialmente resistentes y, el 16 %, resistentes al benzonidazol. Los análisis de correlación entre las CI50 con algunos parámetros biológicos y eco-epidemiológicos, mostraron diferencias en cuanto a la sensibilidad según el origen biológico y el área geográfica de procedencia de la cepa. Conclusiones. Existe una gran variabilidad en cuanto a la sensibilidad al benzonidazol de las cepas circulantes de T. cruzi en Colombia, lo cual sugiere la presencia de cepas naturalmente resistentes en el país.   doi: http://dx.doi.org/10.7705/biomedica.v32i2.458

Espacios vectoriales y seudotopologías compatibles

OpenAIRE

Muñoz Q., José M.

2012-01-01

Al tratar de extender el concepto de diferenciabilidad  a los espacios vectoriales topológicos no normados, se ha comprobado que no existen en general topologías convenientes sobre los espacios de funciones involucrados.

Financial cost of amyotrophic lateral sclerosis: a case study.

Science.gov (United States)

Obermann, M; Lyon, M

2015-03-01

There are only a few recently published reports of the cost of amyotrophic lateral sclerosis (ALS) care in the United States. Our objectives were to: 1) report annual and disease-duration costs; 2) provide costs related to specific care and services; 3) present costs by payor; and 4) identify strategies and resources that can be offered to patients to assist with the financial burden of ALS. Over a 10-year period (2001-2010), all expenses related to the cost of care for an individual patient were collected concurrently and then analyzed in 2012. Results showed that total disease-duration costs were $1,433,992 (85% paid by insurance, 9% paid by family, 6% paid by charities). The highest costs were for in-home caregivers ($669,150), ventilation ($212,430) and hospital care ($114,558). In conclusion, this case study illustrates costs of care for ALS as a burden for patients that may impact treatment decisions. Charity organizations and insurance case-managers provide services to patients that can help reduce this burden. Costs for specific services as well as resources identified by this study offer physicians and other healthcare providers data-based cost of care information and strategies to share with their patients.

Interculturalidad y educación. Aportación al estado del arte en Etnomatemáticas

Directory of Open Access Journals (Sweden)

Juan Luis Piñeiro

2016-07-01

Full Text Available Las investigaciones crecientes en el área de la Etnomatemática han generado un amplio escenario de discusión en el campo de la educación matemática, y por consiguiente es posible observar un gran número de aportes a nivel mundial. En este sentido, se plantea la necesidad de indagar sobre cuáles son los aspectos principales que preocupan en este campo de la educación y contribuir de esta manera, al estado del arte sobre la Etnomatemática, y por consiguiente a la educación matemática y la diversidad cultural. Para afrontar este problema, se realizó en primer lugar, una búsqueda sistemática de publicaciones científicas, en actas de congresos y revistas de impacto durante el periodo 2014-2015, de la cual se obtuvieron 48 documentos vinculados al área de la etnomatemática de manera explícita o implícita. En segundo lugar, se analizó la muestra teniendo en cuenta el modelo MOMUME de Oliveras (2000, 2008a, 2008b. Esta herramienta metodológica nos permitió reflexionar sobre las tendencias que se están configurando en Etnomatemática y contribuir al estado del arte en este programa. Los resultados muestran tendencia a tratar temas tales como: sociedad, cultura y modelo educativo, a través de experimentos de campo y con metodologías cualitativas, fundamentados en las matemáticas como un constructo social y cultural.

El Servicio al cliente: ¡Más que un querer, un deber!

Directory of Open Access Journals (Sweden)

Gustavo Vargas Vargas

2013-02-01

Full Text Available Uno de los aspectos más importantes en la generaciónde diferenciación con respecto a la competencia loconstituye “el Servicio al Cliente”. El Servicio al Cliente presenta características, queconvierten su tratamiento en complejo de implementar:Por ejemplo se menciona que el Servicio es intangible;que el Servicio es variable; que el Servicio se producey se consume a la vez; y, que el Servicio no puede seralmacenado. Lo anterior es influido por la cultura del paísdonde se ubique la empresa. El tratar el tema del Servicio al Cliente es muyimportante en aras de poder mantener a nuestros clientes.En este sentido, varias investigaciones citadas evidencianel impacto de un mal manejo del Servicio al Cliente, asícomo cifras ligadas en general a su comportamiento. El Servicio al Cliente se puede definir como el conjuntode aspectos relacionados con los clientes, y no sólo setrata de atención al cliente, aspecto que es comúnmenteconfundido con el primero. La atención al cliente es partedel Servicio, pero no lo es todo! Es necesario escapar de seguir tratando este tema consuperficialidad, y más bien, aprovechar su implementacióncomo medio de generar ventajas competitivas ante lacompetencia.   ABSTRACT One of the most important aspects in the generationof a differentiation with your competition is constitutedby “Customer Service”. Customer Service presents several characteristicsthat make it complex to implement: For example itis mentioned that Service is intangible; that Serviceis variable; that Service is produced and consumedsimultaneously; and, that Service cannot be stored. Thisis influenced by the culture of the country where thecompany is located. Dealing with the subject of Customer Service is veryimportant for the sake of being able to maintain ourclients. In this sense several quoted investigations showthe impact of a badly handed Customer Service, as wellas financial figures related to its performance. Customer Service can be

Régimen de las moratorias en las provincias argentinas de Salta (1825 y Tucumán (1861

Directory of Open Access Journals (Sweden)

Abelardo Levaggi

2018-01-01

Full Text Available Entre los beneficios para los comerciantes, según las Ordenanzas del Consulado de Bilbao de 1737, estaban las esperas y las quitas, que no incluían a los fallidos fraudulentos. El deudor podía tratar extrajudicialmente con los acreedores y después presentarse al juez o pedirle al juez que reuniese a los acreedores y así tratar con ellos. En ambos casos la decisión de la mayoría podría obligar a la minoría. Este sistema fue discutido después de la independencia. El motivo fue proteger a los comerciantes honrados perjudicados por la guerra y otras desgracias, pero también evitar la mala fe. La provincia argentina de Salta (además de Buenos Aires y Tucumán fue un ejemplo de esa discusión.

Coste-efectividad de la adición de acarbosa al tratamiento de pacientes con diabetes tipo 2 en España Cost-effectiveness of the addition of acarbose to the treatment of patients with type-2 diabetes in Spain

OpenAIRE

Carme Piñol; Stephane Roze; William Valentine; Thomas Evers

2007-01-01

Objetivos: Evaluar el coste-efectividad de la adición de acarbosa al tratamiento de pacientes con diabetes mellitus tipo 2 (DM2) en España. Métodos: Se utilizó el CORE Diabetes Model (modelo de simulación informática publicado y validado) para proyectar a largo plazo los resultados clínicos y de costes de la DM2. Las probabilidades de transición y los riesgos se obtuvieron de distintas publicaciones. Los efectos del tratamiento y las características basales de la cohorte se obtuvieron de un m...

34 - 38 Ashiru et al.

African Journals Online (AJOL)

User

INTRODUCTION. Commercial fish feeds are usually expensive because the traditional or conventional protein source ingredient such as fish meal, soyabean ... consumption (Madu et al., 2003). Fish feed constitute for about 60-80% of management cost in agricultural production (Igonifagha, 1979). Periodic scarcity and.

Cast Aluminum Alloys for High Temperature Applications Using Nanoparticles Al2O3 and Al3-X Compounds (X = Ti, V, Zr)

Science.gov (United States)

Lee, Jonathan A.

2009-01-01

In this paper, the effect of nanoparticles Al2O3 and Al3-X compounds (X = Ti, V, Zr) on the improvement of mechanical properties of aluminum alloys for elevated temperature applications is presented. These nanoparticles were selected based on their low cost, chemical stability and low diffusions rates in aluminum at high temperatures. The strengthening mechanism at high temperature for aluminum alloy is based on the mechanical blocking of dislocation movements by these nanoparticles. For Al2O3 nanoparticles, the test samples were prepared from special Al2O3 preforms, which were produced using ceramic injection molding process and then pressure infiltrated by molten aluminum. In another method, Al2O3 nanoparticles can also be homogeneously mixed with fine aluminum powder and consolidated into test samples through hot pressing and sintering. With the Al3-X nanoparticles, the test samples are produced as precipitates from in-situ reactions with molten aluminum using conventional permanent mold or die casting techniques. It is found that cast aluminum alloy using nanoparticles Al3-X is the most cost effective method to produce high strength aluminum alloys for high temperature applications in comparison to nanoparticles Al2O3. Furthermore, significant mechanical properties retention in high temperature environment could be achieved with Al3-X nanoparticles, resulting in tensile strength of nearly 3 times higher than most 300- series conventional cast aluminum alloys tested at 600 F.

Effectiveness of see-and-treat for approaching pre-invasive lesions of uterine cervix Efectividad del abordaje "ver y tratar" en lesiones pre-invasivas en el colon uterino Efetividade da abordagem "ver e tratar" em lesões pré-invasivas no colo uterino

Directory of Open Access Journals (Sweden)

Aparecida Cristina Sampaio Monteiro

2009-10-01

Full Text Available OBJECTIVE: To compare the effectiveness between the see-and-treat (S&T approach and the conventional one (with prior biopsy for squamous intraepithelial lesions of uterine cervix. METHODS: A cross-sectional study was conducted with 900 nonpregnant women with cytology suggestive of high grade squamous intraepithelial lesions in the city of Rio de Janeiro, Southeastern Brazil, between 1998 and 2004. The S&T approach consists of a large loop excision of the transformation zone procedure and is recommended when cytology is suggestive of high grade squamous intraepithelial lesion, satisfactory colposcopy with abnormalities compatible with the suspected cytological results, and the lesion is limited to the ectocervix or extends up to one centimeter of the endocervical canal. A subgroup of 336 patients whose colposcopy was considered satisfactory was analyzed, and they were divided into two groups for comparison: patients treated without prior biopsy (n = 288 and patients treated after a biopsy showing high grade squamous intraepithelial lesions (n = 48. Patients who were not treated or only treated more than a year later after recruitment at the colposcopy unit were considered dropouts. RESULTS: Of patients recruited during the study period, 71 were not treated or were only treated for at least a year. The overall dropout rate was 7.9% (95% CI: 6.1;9.7. Mean time elapsed between patient recruitment and treatment was 17.5 days in the S&T group and 102.5 days in the prior biopsy group. Dropout rates were 1.4% (95% CI: 0.04;2.7 and 5.% (95% CI: 0;12.3, respectively (p=0.07. The proportion of overtreated cases (negative histology in the S&T group was 2.0% (95% CI: 0.4;3.6. CONCLUSIONS: The difference in the mean time elapsed between patient recruitment and treatment indicates that S&T is a time-saving approach The proportion of negative cases from using the S&T approach can be regarded as low.OBJETIVO: Comparar la efectividad del método "ver-y-tratar" (V

Poniendo al habitus en su lugar: réplica del simposio

Directory of Open Access Journals (Sweden)

Loïc Wacquant

2014-09-01

Full Text Available En respuesta a mis críticos, amplío la clarificación conceptual y la estipulación metodológica del habitus emprendida en “Homines in Extremis” para ayudarnos a movernos desde una sociología del cuerpo con un objeto socialmente constru-ído a una sociología desde el cuerpo como un vector de conocimiento, poder y práctica que está construyén-dose socialmente. La especificación del habitus según la pertenencia a colectivos, la vinculación con instituciones, y el propósito analítico hace que sea una noción multi-escalar flexible con la cual construir el individuo epistémico y dar cuenta de la reproducción y el cambio, el conformismo y la creatividad, así como también una auto-revisión. Para esto, debemos rechazar las interpretaciones teológicas que rígidamente encierran al habitus en el contexto de Bourdieu; evitar confundir las propiedades formales de la noción con sus características concretas en contextos y casos específicos; y distinguir entre la invocación retórica de sus conceptos (“hablando bourdesianamente” y la eficacia de su despliegue en la construcción del objeto empírico. Con su capacidad de corporizarse e incrustarse, el habitus aporta temporalidad, profundidad, y deseo al epicentro analítico. Nos recuerda que el mundo social no es transparente, abierto e instantáneo, sino dotado de gravedad, opacidad, y asimetría. Tratar al organismo sensible y hábil como fuente de inteligencia social y perspicacia sociológica puede ayudar a la ciencia social histórica a conectarse con una psicología enactiva y recuperar la carnalidad de la acción que los reportes convencionales de la vida social borran rutinariamente.

Poniendo al habitus en su lugar: réplica del simposio

Directory of Open Access Journals (Sweden)

Loïc Wacquant

2014-08-01

Full Text Available En respuesta a mis críticos, amplío la clarificación conceptual y la estipulación metodológica del habitus emprendida en “Homines in Extremis” para ayudarnos a movernos desde una sociología del cuerpo con un objeto socialmente constru- ído a una sociología desde el cuerpo como un vector de conocimiento, poder y práctica que está construyén-dose socialmente. La especificación del habitus según la pertenencia a colectivos, la vinculación con instituciones, y el propósito analítico hace que sea una noción multi-escalar flexible con la cual construir el individuo epistémico y dar cuenta de la reproducción y el cambio, el conformismo y la creatividad, así como también una auto-revisión. Para esto, debemosrechazar las interpretaciones teológicas que rígidamente encierran al habitus en el contexto de Bourdieu; evitar confundir las propiedades formales de la noción con sus características concretas en contextos y casos específicos; y distinguir entre la invocación retórica de sus conceptos (“hablando bourdesianamente” y la eficacia de su despliegue en la construcción del objeto empírico. Con su capacidad de corporizarse e incrustarse, el habitus aporta temporalidad, profundidad, y deseo al epicentro analítico. Nosrecuerda que el mundo social no estransparente, abierto e instantáneo,sino dotado de gravedad, opacidad, y asimetría. Tratar al organismo sensible y hábil como fuente de inteligencia social y perspicacia sociológica puede ayudar a la ciencia social histórica a conectarse con una psicología enactiva y recuperar la carnalidad de la acción que los reportes convencionales de la vida social borran rutinariamente.

Financing Investment: The Cost Trade-Off

DEFF Research Database (Denmark)

Hirth, Stefan; Flor, Christian Riis

Intuition suggests that corporate investment should be decreasing in financing constraints. We show that even when financing is obtained using a standard debt contract and there is symmetric information between the firm and outside investors, the relation is actually U-shaped. We thus provide a new...... theoretical explanation for the recent empirical findings of Cleary et al. (2007). We split up the endogenously implied financing costs and propose a trade-off between expected liquidation costs and second-best investment costs. For rather unconstrained firms, the risk of costly liquidation dominates the cost...

Um modelo de otimização para alíquotas do IPTU socialmente mais justas Un modelo de optimización de las tasas de impuestos a la propiedad socialmente más justo An optimization model for rates of socially fairer property tax

Directory of Open Access Journals (Sweden)

José Delfino Sá

2013-02-01

Full Text Available Este artigo apresenta um modelo de otimização matemática não linear que determina novas alíquotas para o Imposto sobre a Propriedade Predial e Territorial Urbana (IPTU incidente sobre os apartamentos residenciais no município do Salvador (BA. São considerados a progressividade das alíquotas, os valores venais dos imóveis, as rendas médias dos contribuintes e as usuais metodologias de cálculo do valor do imposto. Os resultados obtidos na aplicação desse modelo demonstram ser possível tratar de forma objetiva e socialmente mais justa a definição das alíquotas de IPTU para todos os tipos de imóveis de um município.En este trabajo se presenta un modelo de optimización matemática no lineal que determinan las nuevas tarifas del Impuesto Inmobiliario Urbano - Impuesto sobre la propiedad aplicado en apartamentos residenciales en la ciudad de Salvador (BA. Ellos se consideran la progresividad de los tipos impositivos, el mercado de valores de las propiedades, los ingresos medios de los contribuyentes y de los métodos habituales de cálculo de la cuantía del impuesto. Los resultados demuestran que la aplicación de este modelo se puede tratar de manera objetiva y socialmente más justo fijar los tipos de impuestos a la propiedad para todos los tipos de propiedades en un municipio.This article presents a nonlinear mathematical optimization model that determines new rates for the Urban Property Tax (IPTU on the residential apartments in the city of Salvador (BA. It considers the progressive increase in rates, the market values of properties, the taxpayers' average incomes, and the usual methodologies of the tax system. The results obtained in applying this model demonstrate that is possible to set tax rates in an objective and equitable manner in all kinds of urban property.

Carga de enfermedad atribuible al uso de tabaco en Argentina y potencial impacto del aumento de precio a través de impuestos

Directory of Open Access Journals (Sweden)

Andrea Alcaraz

Full Text Available RESUMEN Objetivo Evaluar la carga de enfermedad asociada al consumo de tabaco en Argentina y estimar el impacto sanitario y económico de aumentos de precio en los cigarrillos a través de impuestos. Métodos Se utilizó un modelo de microsimulación para cuantificar el impacto en la mortalidad, calidad de vida y costos atribuibles al tabaquismo por enfermedad cardiovascular, cerebrovascular y pulmonar obstructiva crónica, neumonía y diez neoplasias. Se modeló el efecto de diferentes escenarios de aumento de precio en el consumo de tabaco y su impacto en los ámbitos sanitario y económico. Resultados En Argentina, se pueden atribuir 44 851 muertes, 20 620 diagnósticos de cáncer, 14 405 accidentes cerebrovasculares y 68 100 hospitalizaciones por enfermedad cardiovascular por año al tabaquismo. Cada año se pierden 998 881 años de vida por muerte prematura y discapacidad. El costo de tratar los problemas de salud atribuibles asciende a 33 mil millones de pesos argentinos (ARS. Los impuestos al tabaco llegan a cubrir solo 67,3% del gasto. Si Argentina aumentara el precio de los cigarrillos en 50%, en los próximos 10 años se podrían evitar 25 557 muertes, 42 560 eventos cardiovasculares y 11 222 cánceres y se obtendría un beneficio económico de 122 mil millones de ARS por ahorro de costos sanitarios y aumento de la recaudación impositiva (1 USD = 8,8096 ARS. Conclusiones La carga de enfermedad y el costo para el sistema de salud atribuibles al tabaquismo son muy elevados en Argentina. Un aumento de los impuestos al cigarrillo podría tener importantes beneficios sanitarios y económicos.

Summit Station Skiway Cost Analysis

Science.gov (United States)

2016-07-01

of fuel delivered to Summit via LC-130 at a price of $32/gal. (Lever et al. 2016), the cost for constructing and maintaining the skiway for the 2014...CRREL TR-16-9 18 The costs associated with the Twin Otter include a day rate plus an hourly mission rate, a per passenger rate, airport fees, fuel, a...ER D C/ CR RE L TR -1 6- 9 Engineering for Polar Operations, Logistics, and Research (EPOLAR) Summit Station Skiway Cost Analysis Co ld

Costos de atención médica atribuibles al tabaquismo en el IMSS, Morelos Costs of medical care attributable to tobacco consumption at the Mexican Institute of Social Security (IMSS, Morelos

Directory of Open Access Journals (Sweden)

Luz Myriam Reynales-Shigematsu

2005-12-01

Full Text Available OBJETIVO: Estimar los costos de atención médica en el Instituto Mexicano del Seguro Social (IMSS, Delegación Morelos, de las enfermedades mayores atribuibles al consumo de tabaco. MATERIAL Y MÉTODOS: Las estimaciones de costos se realizaron desde la perspectiva del proveedor utilizando la metodología de costeo de enfermedad. Un panel de expertos multidisciplinario caracterizó la atención médica, en términos de la frecuencia de utilización de servicios en el primer y segundo niveles de atención, considerando el grado de severidad de la enfermedad. Los costos unitarios se estimaron en pesos mexicanos del 2001. Para estimar los costos atribuibles al tabaquismo se utilizó la fracción atribuible al consumo de tabaco para cada enfermedad (FA. RESULTADOS: Los costos promedio anuales de atención médica en el primer y segundo niveles de atención en la Delegación Morelos corresponden a 79 530 pesos para infarto agudo del miocardio (IAM, 73 303 pesos para enfermedad pulmonar obstructiva crónica (EPOC y 102 215 pesos para cáncer de pulmón (CP. El costo total anual para la Delegación por estas tres enfermedades asciende a 147 millones 390 mil 688 pesos. Los costos atribuibles al consumo de tabaco corresponden a 124 millones de pesos, lo cual equivale a 7.3% del presupuesto anual de la Delegación. CONCLUSIONES: Estos resultados confirman el alto costo de la atención médica en el IMSS correspondiente a las enfermedades atribuibles al consumo de tabaco. Se recomienda realizar este estudio en el plano nacional, de tal manera que los tomadores de decisiones tengan herramientas para fortalecer las políticas de control del tabaquismo en México.OBJECTIVE: To estimate the cost of medical care for the major diseases attributable to tobacco consumption at the IMSS, Morelos. MATERIAL AND METHODS: A cost of illness (COI analysis was carried out from the perspective of the health provider. An expert panel characterized medical care in primary and

Beneficios económicos del implante coclear para la hipoacusia sensorineural profunda Economic benefits of the cochlear implant for treating profound sensorineural hearing loss

Directory of Open Access Journals (Sweden)

Augusto Peñaranda

2012-04-01

Full Text Available OBJETIVO: Evaluar el costo-beneficio (CB, costo-utilidad (CU y costo-efectividad (CE de la implantación coclear, comparándola con el uso de audífonos en niños con hipoacusia sensorineural profunda bilateral. MÉTODOS: Se empleó la técnica no paramétrica Propensity Score Matching (PSM para realizar la evaluación de impacto económico del implante y así llevar a cabo los análisis CB, CU y CE. Se utilizó información primaria, tomada aleatoriamente a 100 pacientes: 62 intervenidos quirúrgicamente con el implante coclear (grupo de tratamiento y 38 pertenecientes al grupo de control o usuarios de audífono para tratar la hipoacusia sensorineural profunda. RESULTADOS: Se halló un diferencial de costos económicos -en beneficio del implante coclear- cercano a US$ 204 000 entre el implante y el uso de audífonos durante la esperanza de vida de los pacientes analizados. Dicha cifra indica los mayores gastos que deben cubrir los pacientes con audífono. Con este valor descontado, el indicador costo-beneficio señala que por cada dólar invertido en el implante coclear, para tratar al paciente, el retorno de la inversión es US$ 2,07. CONCLUSIONES: El implante coclear genera beneficios económicos para el paciente. También produce utilidades en salud dado que se encontró una relación positiva de CU (ganancia en decibeles y CE (ganancia en discriminación del lenguaje.OBJECTIVE: Evaluate the cost-benefit, cost-utility, and cost-effectiveness of cochlear implantation, comparing it to the use of hearing aids in children with profound bilateral sensorineural hearing loss. METHODS: The nonparametric propensity score matching method was used to carry out an economic and impact assessment of the cochlear implant and then perform cost-benefit, cost-utility, and cost-effectiveness analyses. Primary information was used, taken randomly from 100 patients: 62 who received cochlear implants (treatment group and 38 belonging to the control group who used

Modeling of TiAl Alloy Grating by Investment Casting

OpenAIRE

Yi Jia; Shulong Xiao; Jing Tian; Lijuan Xu; Yuyong Chen

2015-01-01

The investment casting of TiAl alloys has become the most promising cost-effective technique for manufacturing TiAl components. This study aimed to investigate a series of problems associated with the investment casting of TiAl alloys. The mold filling and solidification of this casting model were numerically simulated using ProCAST. Shrinkage porosity was quantitatively predicted by a built-in feeding criterion. The results obtained from the numerical simulations were compared with experimen...

Stereo Disparity through Cost Aggregation with Guided Filter

Directory of Open Access Journals (Sweden)

Pauline Tan

2014-10-01

Full Text Available Estimating the depth, or equivalently the disparity, of a stereo scene is a challenging problem in computer vision. The method proposed by Rhemann et al. in 2011 is based on a filtering of the cost volume, which gives for each pixel and for each hypothesized disparity a cost derived from pixel-by-pixel comparison. The filtering is performed by the guided filter proposed by He et al. in 2010. It computes a weighted local average of the costs. The weights are such that similar pixels tend to have similar costs. Eventually, a winner-take-all strategy selects the disparity with the minimal cost for each pixel. Non-consistent labels according to left-right consistency are rejected; a densification step can then be launched to fill the disparity map. The method can be used to solve other labeling problems (optical flow, segmentation but this article focuses on the stereo matching problem.

Aislamiento, caracterización y reprogramación de células multipotentes murinas en ratones transgénicos "mTert-EGFP"

OpenAIRE

Pericuesta Camacho, Eva

2011-01-01

La presente tesis está compuesta por tres artículos científicos publicados (Pericuesta et al., 2006; Ramirez et al., 2006; Ramírez et al., 2007) y un último trabajo realizado para completar el análisis de las células troncales en tejidos adultos. La importancia de las células troncales ha crecido enormemente en las últimas décadas debido al gran potencial que presentan para tratar enfermedades hasta hoy incurables como el Parkinson, la diabetes tipo I, la enfermedad de Alzheimer, esclerosis m...

Ulcera gastro duodenal y parasitosis en Bogotá, D.E.

Directory of Open Access Journals (Sweden)

Alberto Albornoz Plata

1956-08-01

Full Text Available Posiblemente la úlcera péptica ocupa los primeros puestos en frecuencia en las Estadísticas Gastroenterológicas. Su tratamiento contempla la erradicación o control de cualquier otra enfermedad concomitante: así es frecuente que al tratar una Sinusitis o al controlar un estado emocional, el tratamiento antiulceroso adquiere un terreno firme y así hay más probabilidad de éxito.

Advanced life support (ALS) instructors experience of ALS education in Western Australia: a qualitative exploratory research study.

Science.gov (United States)

Taplin, John; McConigley, Ruth

2015-04-01

When cardiac arrest occurs, timely competent advanced life support (ALS) interventions by nursing staff can influence patient outcomes. Ongoing ALS education influences maintenance of competency and avoids skill decay. To explore the methods of ALS education delivery for nurses in the workplace; describe the issues relating to maintaining ALS competency; explore ALS competency decay for nurses and develop recommendations for the provision of continuing ALS education. A qualitative exploratory design was used to study ALS education provision in the workplace. Data were collected from ALS nurse experts in Western Australia by face-to-face and phone interviews. Semi-structured interviews were conducted and organised around a set of predetermined questions. Two major themes were identified; the first theme Demand and Supply describes the increasing demand for ALS education for nurses and the challenges with providing timely cost effective traditional face-to-face ALS education. The second theme, Choosing The Best Education Options describes new ways to provide ALS education using emerging technologies. The study suggested that using e-learning methods would assist with educating the maximum amount of nurses in a timely manner and e-learning and teleconferencing offer opportunities to reach nurses in distant locations. Delivering ALS education more frequently than annually would increase skills maintenance and lessen skill decay. Further research is required to explore which blended e-learning model is best suited to ALS education. Copyright © 2014 Elsevier Ltd. All rights reserved.

Organic light-emitting diodes using novel embedded al gird transparent electrodes

Science.gov (United States)

Peng, Cuiyun; Chen, Changbo; Guo, Kunping; Tian, Zhenghao; Zhu, Wenqing; Xu, Tao; Wei, Bin

2017-03-01

This work demonstrates a novel transparent electrode using embedded Al grids fabricated by a simple and cost-effective approach using photolithography and wet etching. The optical and electrical properties of Al grids versus grid geometry have been systematically investigated, it was found that Al grids exhibited a low sheet resistance of 70 Ω □-1 and a light transmission of 69% at 550 nm with advantages in terms of processing conditions and material cost as well as potential to large scale fabrication. Indium Tin Oxide-free green organic light-emitting diodes (OLED) based on Al grids transparent electrodes was demonstrated, yielding a power efficiency >15 lm W-1 and current efficiency >39 cd A-1 at a brightness of 2396 cd m-2. Furthermore, a reduced efficiency roll-off and higher brightness have been achieved compared with ITO-base device.

Analysis of methods for evaluating environmental costs: a view from environmental accounting research. case: construction of highway, vía al mar Cartagena-Barranquilla section 1

Directory of Open Access Journals (Sweden)

José Julio Vergara Arrieta

2016-11-01

Full Text Available This document is the first breakthrough in the research project entitled “Measurement and assessment of social and environmental costs of Dual Carriageway Vía al Mar Cartagena- Barranquilla section 1 Barrio Crespo – Entrance Villages Tierra Baja and Puerto Rey” funded by the University of San Buenaventura Cartagena. In it the conclusions of the search and theoretical-critical analysis of the different methods, methodologies or techniques that address the issue of valuation of environmental quality in order to develop the first approaches to valuation exercise environmental costs are collected. The position for the present analysis is adopted from an investigative standpoint of accounting field, based on performing and / or environmental reality heterodox approaches.

Low-cost ZnO:Al transparent contact by reactive rotatable magnetron sputtering for Cu(In,Ga)Se2 solar modules

International Nuclear Information System (INIS)

Menner, R.; Hariskos, D.; Linss, V.; Powalla, M.

2011-01-01

Sputtering ZnO as transparent front contact (TCO) is standard in today's industrial scale Cu(In,Ga)Se 2 (CIGS) module manufacturing. Although innovative concepts like rotatable magnetron sputtering from ceramic targets have been realised, costs are still high due to expensive ceramic targets. Significant cost reductions are expected by using reactive sputtering of metallic targets. Therefore, ZSW and industrial partners investigated the reactive sputtering of Al-doped zinc oxide (ZAO) as TCO on CIGS absorbers of high quality and industrial relevance. The reactive DC sputtering from rotatable magnetron targets is controlled in the transition mode by adjusting oxygen flow and discharge voltage. Optimisation leads to ZAO films with a TCO quality nearly comparable to standard films deposited by DC ceramic sputtering. Scanning electron microscopy, X-ray diffraction, and Hall analyses of the ZAO films are performed. Medium-size CIGS modules are coated with reactively sputtered ZAO, resulting in 12.8% module efficiency and surpassing the efficiency of the ceramic witness device. Cd-free buffered devices are also successfully coated with reactive TCO. Damp heat stability according to IEC61646 is met by all reactively sputtered devices.

A cost-effectiveness analysis of artemether lumefantrine for treatment of uncomplicated malaria in Zambia

Directory of Open Access Journals (Sweden)

Hawela Moonga

2007-02-01

Full Text Available Abstract Background Malaria remains a leading cause of morbidity, mortality and non-fatal disability in Zambia, especially among children, pregnant women and the poor. Data gathered by the National Malaria Control Centre has shown that recently observed widespread treatment failure of SP and chloroquine precipitated a surge in malaria-related morbidity and mortality. As a result, the Government has recently replaced chloroquine and SP with combination therapy as first-line treatment for malaria. Despite the acclaimed therapeutic advantages of ACTs over monotherapies with SP and CQ, the cost of ACTs is much greater, raising concerns about affordability in many poor countries such as Zambia. This study evaluates the cost-effectiveness analysis of artemether-lumefantrine, a version of ACTs adopted in Zambia in mid 2004. Methods Using data gathered from patients presenting at public health facilities with suspected malaria, the costs and effects of using ACTs versus SP as first-line treatment for malaria were estimated. The study was conducted in six district sites. Treatment success and reduction in demand for second line treatment constituted the main effectiveness outcomes. The study gathered data on the efficacy of, and compliance to, AL and SP treatment from a random sample of patients. Costs are based on estimated drug, labour, operational and capital inputs. Drug costs were based on dosages and unit prices provided by the Ministry of Health and the manufacturer (Norvatis. Findings The results suggest that AL produces successful treatment at less cost than SP, implying that AL is more cost-effective. While it is acknowledged that implementing national ACT program will require considerable resources, the study demonstrates that the health gains (treatment success from every dollar spent are significantly greater if AL is used rather than SP. The incremental cost-effectiveness ratio is estimated to be US$4.10. When the costs of second line

68 - 75 Galadanchi et al.c

African Journals Online (AJOL)

User

Restricted HartreeFock (RHF) and Density Functional Theory (DFT) studies were carried out on the organic semi ... arrays), organic light emitting diodes (OLEDs), solar cells and low-cost devices (Kitamura,Arakawa, 2008;. Hwan et al.2004; Byoungnan,2008). Organic semiconductors are materials with semiconducting.

Offshore Wind Resource, Cost, and Economic Potential in the State of Maine

Energy Technology Data Exchange (ETDEWEB)

Musial, Walter D. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2018-02-12

This report provides information for decision-makers about floating offshore wind technologies in the state of Maine. It summarizes research efforts performed at the National Renewable Energy Laboratory between 2015 and 2017 to analyze the resource potential, cost of offshore wind, and economic potential of offshore wind from four primary reports: Musial et al. (2016); Beiter et al. (2016, 2017); and Mone et al. (unpublished). From Musial et al. (2016), Maine's technical offshore wind resource potential ranked seventh in the nation overall with more than 411 terawatt-hours/year of offshore resource generating potential. Although 90% of this wind resource is greater than 9.0-meters-per-second average velocity, most of the resource is over deep water, where floating wind technology is needed. Levelized cost of energy and levelized avoided cost of energy were computed to estimate the unsubsidized 'economic potential' for Maine in the year 2027 (Beiter et al. 2016, 2017). The studies found that Maine may have 65 gigawatts of economic potential by 2027, the highest of any U.S. state. Bottom-line costs for the Aqua Ventus project, which is part of the U.S. Department of Energy's Advanced Technology Demonstration project, were released from a proprietary report written by NREL in 2016 for the University of Maine (Mone et al. unpublished). The report findings were that economies of scale and new technology advancements lowered the cost from $300/megawatt-hour (MWh) for the two-turbine 12-megawatt (MW) Aqua Ventus 1 project, to $126/MWh for the commercial-scale, 498-MW Aqua Ventus-2 project. Further cost reductions to $77/MWh were found when new technology advancements were applied for the 1,000-MW Aqua Ventus-3 project in 2030. No new analysis was conducted for this report.

La culpa y la vergüenza en la sexualidad adolescente: una perspectiva de género

OpenAIRE

Cadena López, Judith

2005-01-01

En el presente trabajo trataré de analizar aspectos relacionados con las manifestaciones de culpabilidad y vergüenza ligadas al ejercicio de la sexualidad, especialmente entre adolescentes y jóvenes. Haré alusión también, a algunas de las emociones que junto con la culpa y la vergüenza matizan el comportamiento de las personas, al momento de abordar tópicos relacionados con la sexualidad, situaciones de violencia y, en general al momento de mantener una relación interpers...

Mechanical Properties of Nano structured TiC-FeAl Hard Materials

International Nuclear Information System (INIS)

Shon, In-Jin; Jo, Hyoung-Gon; Kim, Byung-Su; Yoon, Jin-Kook; Hong Kyung-Tae

2015-01-01

For the formation of cemented Tic composite, Co or Ni is added as a binder. However, the high cost and low hardness of Co or Ni as binder and the low corrosion resistance of Tic-Co and Tic-Ni composite have generated interest to find alternative binder materials. It has been reported that FeAl show higher oxidation resistance and hardness as well as low cost compared to Co or Ni. Highly dense nanocrystalline Tic and Tic-FelAl with a relative density of up to 100% were obtained within 2 min by PCAS(pulsed current activated sintering) under the condition of 80MPa and up to 1300. The effect of FeAl addition of FeAl on the consolidation, the microstructure and the mechanical properties (hardness and fracture toughness) of TiC were investigated. The fracture toughness of TiC greatly increases without great decrease of the hardness by addition of FeAl. Not only fracture toughness but also hardness values of TiC-10vol.%FeAl were higher than those of TiC-10vol.%Fe, TiC-10vol.%Ni and TiC-10vol.%Co.

Optimization of the boron content in FeAl (40 at. % Al) alloys

International Nuclear Information System (INIS)

Webb, G.; Juliet, P.; Lefort, A.

1993-01-01

FeAl intermetallic alloys are of interest for several high temperature applications due to excellent oxidation resistance, low density, and relatively low cost. Attempts to further increase the ductility of iron-rich FeAl have met with, at best, marginal success. Of the ductilization techniques employed, B doping appears to be a promising method for obtaining enhanced ductility and high strength in iron rich FeAl. Boron additions enhance the ductility of these alloys by increasing the grain boundary cohesive strength which reduces the tendency for intergranular fracture. The goal of the present work was to determine the optimum B concentration for increasing ambient temperature ductility. To accomplish this, a series of three iron rich FeAl alloys of similar Fe stoichiometries were doped with different levels of B (0,12, and 80 wppm). Secondary ion mass spectrometry (SIMS) was conducted on these alloys for evaluation of the B partitioning after consolidation by extrusion. Ambient temperature tensile testing and SEM fractography were then used to evaluate the effect of such additions on ambient temperature ductility in air. The results of these experiments indicate that optimum ductility is obtained from a homogeneous distribution of boron in which boride precipitation is limited

Coste-efectividad de la adición de acarbosa al tratamiento de pacientes con diabetes tipo 2 en España Cost-effectiveness of the addition of acarbose to the treatment of patients with type-2 diabetes in Spain

Directory of Open Access Journals (Sweden)

Carme Piñol

2007-04-01

Full Text Available Objetivos: Evaluar el coste-efectividad de la adición de acarbosa al tratamiento de pacientes con diabetes mellitus tipo 2 (DM2 en España. Métodos: Se utilizó el CORE Diabetes Model (modelo de simulación informática publicado y validado para proyectar a largo plazo los resultados clínicos y de costes de la DM2. Las probabilidades de transición y los riesgos se obtuvieron de distintas publicaciones. Los efectos del tratamiento y las características basales de la cohorte se obtuvieron de un metaanálisis. Los costes directos se extrajeron de diversas publicaciones y se proyectaron a lo largo de la vida de los pacientes bajo la perspectiva del Sistema Nacional de Salud de España. Los costes y beneficios fueron descontados en un 3% anual. Se realizaron análisis de sensibilidad. Resultados: El tratamiento con acarbosa se asoció con mejoras en la esperanza de vida (0,23 años y en los años de vida ajustados por calidad (AVAC (0,21 años. Los costes directos fueron en promedio, por paciente, de 468 € más caros con acarbosa que con placebo. La razón de coste-efectividad incremental fue de 2.002 €/año de vida ganado y de 2.199 €/AVAC ganado. La curva de aceptabilidad mostró que con una disponibilidad a pagar de 20.000 €, generalmente aceptada como muy buen valor monetario, el tratamiento con acarbosa se asoció con una probabilidad del 93,5% de ser coste-efectiva. Conclusiones: Este estudio económico a largo plazo mostró que la adición de acarbosa al tratamiento de pacientes con DM2 produjo mejoras en la esperanza de vida y en los AVAC de estos pacientes.Objectives: To assess the cost-effectiveness of the addition of acarbose to existing treatment in patients with type 2 diabetes mellitus (DM2 in Spain. Methods: The CORE Diabetes Model (a published and validated computer simulation model was used to project long-term clinical and cost outcomes in DM2. Transition probabilities and risk adjustments were derived from published

"La pasión de el Cristo": su controversia

Directory of Open Access Journals (Sweden)

Edmundo Rodríguez Castelo

2015-01-01

Full Text Available El autor hace una crítica al filme La pasión de el Cristo de Pasolini y señala que la historia esta fílmicamente contada, sin tratar de endulzar el dolor y la crueldad con la que realmente debieron suceder los hechos.

Magnet costs for the Advanced Light Source

International Nuclear Information System (INIS)

Tanabe, J.; Krupnick, J.; Hoyer, E.; Paterson, A.

1993-05-01

The Advanced Light Source (ALS) accelerator is now completed. The numerous conventional magnets required for the booster ring, the storage ring and the low and high energy transfer lines were installed during the last two years. This paper summarizes the various costs associated with the quantity fabrication of selected magnet families. These costs include the costs of prototypes, tooling, coil and core fabrication, assembly and magnetic measurements. Brief descriptions of the magnets and specialized requirements for magnetic measurements are included in order to associate the costs with the relative complexities of the various magnet systems

Cost Estimates Of Concentrated Photovoltaic Heat Sink Production

Science.gov (United States)

2016-06-01

PV), return on investment (ROI) 15. NUMBER OF PAGES 59 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT Unclassified 18. SECURITY...improvements increase overall system returns on investment and 11 provide pathways for further reduction in system costs (Phillips et al., 2015). Phillips...generation. As the CPV market has matured, production costs have come down to near flat-panel photovoltaic (PV) production costs. CPV units

Cost effectiveness of intermittent screening followed by treatment versus intermittent preventive treatment during pregnancy in West Africa

DEFF Research Database (Denmark)

Fernandes, Silke; Sicuri, Elisa; Halimatou, Diawara

2016-01-01

$/DALY averted. Simulations show that cost-effectiveness of ISTp-AL increases as the efficacy of IPTp-SP decreases, though the specific threshold at which ISTp-AL becomes cost-effective depends on assumptions about the contribution of bed nets to malaria control, bed net coverage and the willingness......-to-pay threshold used.  Conclusions: At SP efficacy levels currently observed in the trial settings it would not be cost-effective to switch from IPTp-SP to ISTp-AL, mainly due to the substantially higher costs of ISTp-AL and limited difference in outcomes. The modelling results indicate thresholds below which IPT......Background: Emergence of high-grade sulfadoxine-pyrimethamine (SP) resistance in parts of Africa has led to growing concerns about the efficacy of intermittent preventive treatment of malaria during pregnancy (IPTp) with SP. The incremental cost-effectiveness of intermittent screening and treatment...

Cost-effectiveness of malaria microscopy and rapid diagnostic tests versus presumptive diagnosis

DEFF Research Database (Denmark)

Batwala, Vincent; Magnussen, Pascal; Hansen, Kristian Schultz

2011-01-01

.9) than in low transmission setting (US$1.78). At a willingness to pay of US$2.8, RDT remained cost effective up to a threshold value of the cost of treatment of US$4.7. CONCLUSION: RDT was cost effective in both low and high transmission settings. With a global campaign to reduce the costs of AL and RDT......ABSTRACT: BACKGROUND: Current Uganda National Malaria treatment guidelines recommend parasitological confirmation either by microscopy or rapid diagnostic test (RDT) before treatment with artemether-lumefantrine (AL). However, the cost-effectiveness of these strategies has not been assessed...... departments were enrolled from March 2010 to February 2011. Of these, a random sample of 1,627 was selected to measure additional socio-economic characteristics. Costing was performed following the standard step-down cost allocation and the ingredients approach. Effectiveness was measured as the number...

Cost-effectiveness evaluation of an RCT in rehabilitation after lumbar spinal fusion: a low-cost, behavioural approach is cost-effective over individual exercise therapy

DEFF Research Database (Denmark)

Søgaard, Rikke; Laurberg, Ida; Christensen, Finn B

2008-01-01

Recently, Christensen et al. reported the clinical effects of a low-cost rehabilitation program equally efficient to a relatively intensive program of individual, physiotherapist-guided exercise therapy. Yet, the low-cost approach is not fully supported as an optimal strategy until a full......-scale economic evaluation, including extra-hospital effects such as service utilization in the primary health care sector and return-to-work, is conducted. The objective of this study was to conduct such evaluation i.e. investigate the cost-effectiveness of (1) a low-cost rehabilitation regimen...... with a behavioural element and (2) a regimen of individual exercise therapy, both in comparison with usual practice, from a health economic, societal perspective. Study design was a cost-effectiveness evaluation of an RCT with a 2-year follow-up. Ninety patients having had posterolateral or circumferential fusion...

Efectos de los costes de cambio y de retención sobre el bienestar social en el servicio postal europeo

OpenAIRE

A. Javier Prado Domínguez; Carlos Pateiro Rodríguez; J. Manuel Barreiro Viñan

2014-01-01

Una política que fortalece la competencia a largo plazo en el sector postal es la actuación sobre los costes de cambio y de retención. En dos escenarios de duopolio, uno con costes de cambio y otro con costes de cambio y costes de retención, el objetivo del presente trabajo es descubrir en qué medida la variación de los costes de cambio de proveedor y de los costes de retención afectan al excedente del consumidor y al beneficio de las dos firmas y, en consecuencia, al bienestar social. Se des...

The operating cost of electrocoagulation

Energy Technology Data Exchange (ETDEWEB)

Donini, J.C.; Kan, J.; Szynkarczuk, J.; Hassan, T.A.; Kar, K.L. (Canadian Centre for Mineral and Energy Technology, Devon, AB (Canada))

1994-12-01

The electrocoagulation of kaolinite and bentonite suspensions was studied in a pilot-scale electrocoagulation system to assess the operating cost and efficiency of the process. Factors affecting the operating cost such as formation of passivation layers on electrode plates, flow velocity, and concentration of NaCl in the suspension were examined. The operating costs investigated were the power cost of the electrocoagulation cell and the material cost due to the consumption of the aluminum electrode. Comparison was based on the settling properties of the treated product: turbidity, settling rate, and cake height. Higher NaCl concentration resulted in greater amounts of Al dissolved chemically and electrochemically into the suspension and thus a better clarity of the supernatant of the treated product. Increased flow velocity could reduce significantly the operating cost while improving both clarity of the supernatant and compactness of the sludge volume. The passivation layers developed quickly with time during the electrocoagulation process and more energy became wasted on the layers. 10 refs., 12 figs.

Cost management technieken voor moderne productieomgevingen

NARCIS (Netherlands)

Veeken, van der H.J.M.; Wouters, M.J.F.

1998-01-01

De huidige ontwikkelingsfase in Management Accounting onderzoek kan worden getypeerd als een nuanceringsfase. Hiermee wordt bedoeld dat na een snelle vernieuwingsgolf, nu een fase van toepasbaarheidsonderzoek en implementatiestudies van cost management vernieuwingen is aangebroken. De eerste

Applications of ZnO:Al deposited by RF sputtering to InN low-cost technology

Energy Technology Data Exchange (ETDEWEB)

Fernandez, S. [Departamento de Energias Renovables, Energia Solar Fotovoltaica, Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Madrid (Spain); Naranjo, F.B.; Valdueza-Felip, S. [Grupo de Ingenieria Fotonica, Departamento de Electronica, Escuela Politecnica Superior, Universidad de Alcala Campus Universitario, Madrid (Spain); Abril, O. de [ISOM y Departamento de Fisica Aplicada, Escuela Tecnica Superior de Ingenieros de Telecomunicacion, Universidad Politenica de Madrid (Spain)

2010-07-15

InN/ZnO:Al heterostructures deposited at low temperature on different substrates by radio-frequency sputtering were studied. Using ZnO:Al as buffer layer, an improvement in the InN structural properties was achieved. Evaluating ZnO:Al as contact on InN, an Ohmic behaviour for the as-deposited layer on InN was achieved. A specific contact resistance of 2 {omega} cm{sup 2} was measured without any post-deposition treatment. These properties could result very promising for optoelectronic device applications. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Crack-free AlGaN-based UV LED on Si(111) substrate

Energy Technology Data Exchange (ETDEWEB)

Saengkaew, P.; Dadgar, A.; Blaesing, J.; Witte, H.; Mueller, M.; Guenther, K.M.; Fey, T.; Bastek, B.; Bertram, F.; Kurnatowski, M. von; Wieneke, M.; Hempel, T.; Veit, P.; Clos, R.; Christen, J.; Krost, A. [FNW/IEP/AHE Otto-von-Guericke-Universitaet Magdeburg (Germany)

2010-07-01

To achieve low-cost UV LEDs on large-diameter substrates it is a very interesting approach to grow AlGaN on low-cost Si substrates. Here, AlGaN layers and AlGaN LED structures grown on Si(111) were additionally monitored by in-situ curvature measurements. They show that with the insertion of AlN-based SL buffer layers and LT-AlN interlayers, the AlGaN layers are under compressive stress during growth enabling to compensate tensile stress after cooling. To characterize the crystalline quality, HR-XRD measurements were performed. Cross-sectional TEM to investigate dislocation propagation and annihilation. n- and p- conductivities were achieved by Si and Mg doping of the layers, respectively. By C-V and Hall-effect measurements, the maximum free-electron concentration of 2.6{sup +18} cm{sup -3} and free-hole concentration of 2.4{sup +17} cm{sup -3} by using a structure of Mg-doped GaN/Al{sub 0.1}Ga{sub 0.9}N multilayers for the latter were determined. A GaN/Al{sub 0.1}Ga{sub 0.9}N MQW structure showed near UV-luminescence around 350-360 nm. The optical and electrical properties of AlGaN-based LED samples were further characterized by I-V, EL, PL and CL measurements. The I-V measurements show forward-diode characteristics with turn-on voltage about 2.6-3.1 V.

Fuzzy ABC: Modelando a Incerteza na Alocação dos Custos AmbientaisFuzzy ABC: Modeling the Uncertainty in Environmental Cost AllocationFuzzy ABC: Modelando la Incertidumbre en la Alocation de los Costos Ambientales

Directory of Open Access Journals (Sweden)

BORBA, José Alonso

2007-05-01

Full Text Available RESUMOEm muitos casos, prevenir a poluição e a destruição do meio ambiente é menos oneroso do que remediar esses danos. Nesse contexto, a alocação de custos ambientais aos produtos permite uma melhor visualização e análise da rentabilidade dos produtos. Entretanto, a alocação dos custos ambientais aos produtos envolve informações estimadas e assume uma linearidade entre o consumo das atividades e os produtos, que muitas vezes não existe. Para contemplar essa não linearidade, esta pesquisa apresenta uma metodologia baseada na utilização da lógica fuzzy para modelar a incerteza e a subjetividade, inerentes ao processo de alocação dos custos ambientais. Para isso, além de um estudo de caso desenvolvido por Hansen e Mowen (2001, p. 584, que foi utilizado como referência, outras variáveis foram incorporadas. Em seguida, uma proposta de solução, que utiliza fundamentos da teoria dos conjuntos fuzzy, ou nebulosos, foi desenvolvida com o objetivo de contemplar a subjetividade e a incerteza na alocação dos custos ambientais. Para simular esse modelo, foram estabelecidas 126 regras de inferência. A etapa final da elaboração do modelo nebuloso consistiu na fuzzificação e defuzzificação dos dados existentes e dos novos direcionadores gerados por intermédio da utilização do software FuzzyTECH®. Os resultados encontrados no modelo proposto - FuzzyABC (Fuzzy Activity Based Costing - evidenciam que a lógica fuzzy pode ser utilizada como uma importante ferramenta para tratar da ambigüidade e da incerteza, inerentes ao processo de alocação dos custos ambientais.ABSTRACTIn many cases, preventing pollution and environmental destruction is cheaper than remedying these damages. In this sense, environmental cost allocation enables a better visualization and analysis of a product’s profitability. However, the environmental allocation process involves estimated information and assumes linearity between activity consumption

Fatiga oligocíclica de la aleación Ti₆Al₄V nitrurada termoquímicamente

Directory of Open Access Journals (Sweden)

Rodríguez, D.

2001-04-01

Full Text Available The use of titanium and its alloys in applications with the presence of friction is limited, due to low hardness and reduced tribological properties. Some surface treatments are available in order to correct these problems, like the thermal surface treatment by means of nitrogen gaseous diffusion at high temperature. Nitrogen enters into the material by diffusion, creating a surface layer of increased hardness. Oligocyclic fatigue behaviour in air of Ti₆Al₄V alloy has been studied. Results show a reduction of oligocyclic fatigue loads up to 10 % compared to the not-treated material. Studies suggest it is not related to the titanium nitride surface layer, but to microstructural changes caused by the high temperature treatment.

El uso del titanio y sus aleaciones en aplicaciones con existencia de fricción es limitado, debido a su baja dureza y malas propiedades tribológicas. Existen diversos tratamientos superficiales capaces de corregir dichos problemas, como el tratamiento térmico superficial mediante difusión gaseosa del nitrógeno a alta temperatura. El nitrógeno penetra en el material a tratar por difusión, formando una capa superficial de elevada dureza. Se ha estudiado el comportamiento a fatiga oligocíclica en aire del Ti₆Al₄V nitrurado. Los resultados muestran una disminución de la resistencia a fatiga oligocíclica de hasta un 10 % respecto al material sin nitrurar. Los estudios sugieren que se debe a cambios en la microestructura causados por el tratamiento a altas temperaturas, y no por la capa superficial de nitruros de titanio.

Novel twin-roll-cast Ti/Al clad sheets with excellent tensile properties.

Science.gov (United States)

Kim, Dae Woong; Lee, Dong Ho; Kim, Jung-Su; Sohn, Seok Su; Kim, Hyoung Seop; Lee, Sunghak

2017-08-14

Pure Ti or Ti alloys are recently spot-lighted in construction industries because they have excellent resistance to corrosions, chemicals, and climates as well as various coloring characteristics, but their wide applications are postponed by their expensiveness and poor formability. We present a new fabrication process of Ti/Al clad sheets by bonding a thin Ti sheet on to a 5052 Al alloy melt during vertical-twin-roll casting. This process has merits of reduced production costs as well as improved tensile properties. In the as-twin-roll-cast clad sheet, the homogeneously cast microstructure existed in the Al alloy substrate side, while the Ti/Al interface did not contain any reaction products, pores, cracks, or lateral delamination, which indicated the successful twin-roll casting. When this sheet was annealed at 350 °C~600 °C, the metallurgical bonding was expanded by interfacial diffusion, thereby leading to improvement in tensile properties over those calculated by a rule of mixtures. The ductility was also improved over that of 5052-O Al alloy (25%) or pure Ti (25%) by synergic effect of homogeneous deformation due to excellent Ti/Al bonding. This work provides new applications of Ti/Al clad sheets to lightweight-alloy clad sheets requiring excellent formability and corrosion resistance as well as alloy cost saving.

Cost Per Flying Hour Analysis of the C-141

Science.gov (United States)

1997-09-01

Government Printing Office, 1996. Horngren , Charles T. Cost Accounting : A Managerial Emphasis (Eighth Edition). New Jersey: Prentice Hall, 1994. Hough...standard accounting techniques. This analysis of AMC’s current costs and their applicability to the price charged to the customer shall be the focus of... Horngren et al.,1994:864). There are three generally recognized methods of determining a transfer price (Arnstein and Gilabert, 1980:189). Cost based

TRABAJO, REMUNERACIÓN Y PRODUCTIVIDAD (Cómo establecer la cuota de remuneración justa al trabajo en base a su productividad marginal TRABAJO, REMUNERACIÓN Y PRODUCTIVIDAD (Cómo establecer la cuota de remuneración justa al trabajo en base a su productividad marginal

Directory of Open Access Journals (Sweden)

Jorge Rionda Ramírez

2012-02-01

Full Text Available Este trabajo hace una propuesta metodológica acerca de cómo medir la cuota justa de remuneración al trabajo con base a su contribución marginal al valor del producto. Se aplica al caso de la producción de bienes tangibles. Parte de un modelo de programación lineal cuya función dual estipula precios sombra que indican la contribución marginal al valor producido de cada unidad de insumo involucrado en la producción. Un acercamiento novedoso dado que en los trabajos marginalistas no existe acercamiento alguno ex profeso en torno al tema de la tasa de explotación y la cuota de remuneración al trabajo. Así también presenta un acercamiento interesante en materia de precios de oportunidad en la sustitución de factores productivos en base al grado de intensidad utilizada del mismo, como de su contribución al valor producido. Con esto se comprueba que aún dentro de la tesis utilitarista el tema de la explotación tiene cabida, simplemente que los teóricos de esta visión evaden el tema por tratar de establecer un planteamiento del problema económico de tipo cientificista, positivo, sin implicaciones de corte político-normativo.This work makes a methodological proposal on how to measure a just remuneration rate for work on the basis of its marginal contribution to product value. It is applied to the production of tangible goods and comes from a linear programming model whose dual function stipulates the shadow prices that indicate the marginal contribution of the value produced of each factor involved in production. It is a novel approach given that in marginalist work no approach exists ex profeso on the subjects of exploitation rate and the remuneration rate for work. It also presents an interesting approach on the subject of opportunity prices with the substitution of productive factors based on the degree of intensity used in production, as well as its contribution to the value produced. It is shown that even within a utilitarian

Parameterized Linear Temporal Logics Meet Costs: Still not Costlier than LTL

Directory of Open Access Journals (Sweden)

Martin Zimmermann

2015-09-01

Full Text Available We continue the investigation of parameterized extensions of Linear Temporal Logic (LTL that retain the attractive algorithmic properties of LTL: a polynomial space model checking algorithm and a doubly-exponential time algorithm for solving games. Alur et al. and Kupferman et al. showed that this is the case for Parametric LTL (PLTL and PROMPT-LTL respectively, which have temporal operators equipped with variables that bound their scope in time. Later, this was also shown to be true for Parametric LDL (PLDL, which extends PLTL to be able to express all omega-regular properties. Here, we generalize PLTL to systems with costs, i.e., we do not bound the scope of operators in time, but bound the scope in terms of the cost accumulated during time. Again, we show that model checking and solving games for specifications in PLTL with costs is not harder than the corresponding problems for LTL. Finally, we discuss PLDL with costs and extensions to multiple cost functions.

Estudios pioneros en torno al origen del lenguaje natural

Directory of Open Access Journals (Sweden)

Martínez Contreras, Jorge

2011-02-01

Full Text Available It has being an ancient desire to ask apes what their natural lives are. De la Mettrie was the first to propose, in the 18^th C., that the sign language of deaf adults could be used with them since they do not speak. We enhance here some of the pioneering projects of the two strategies for this endeavor: the use of ASL and the utilization of lexigrams and computers. Besides the ancient communicative quest with them, the evolutionist’s perspective has seen in these studies a way to find out how the natural language (NL emerged in hominids. If it is clear that apes do no possess totally the NL, the linguistic turn in primatology has left way, as in philosophy, to more complex field and laboratory cognitive studies of less anthropocentric nature.

Tratar de hablar con los simios y preguntarles cosas sobre su vida natural es un viejo deseo. De la Mettrie propone, en el s. XVIII, que se les enseñe el lenguaje de los sordos en vista de que no pueden hablar. Resaltamos aquí algunos estudios pioneros en relación con las dos estrategias llevadas a cabo para tratar de hablar con los simios: el uso del lenguaje americano de sordos (ASL y el de los lexigramas y computadoras. Además del viejo interés interrogativo humano hacia ellos, la perspectiva evolucionista ha visto en estos estudios un medio de investigar cómo surgió el lenguaje natural (LN en homínidos. Si queda claro que los simios no poseen totalmente el LN, el giro lingüistico en primatología ha cedido, como en filosofía, el paso a estudios cognitivos más complejos, de campo y de laboratorio, de orientación menos antropomórfica.

Psicosinergia en Millon: Del modelo Biopsicosocial al modelo Ecológico

OpenAIRE

Jesús R. Herrero Sánchez

2014-01-01

Desde la publicación de Psicopatología Moderna, el modelo psicopatológico de Millon ha evolucionado sustantivamente. En su forma actual, Millon afirma que la estructura de una ciencia clínica consiste en cuatro elementos principales: una teoría que explica los fenómenos bajo observación, (b) una taxonomía que categoriza estos fenómenos en dimensiones significantes, (c) una instrumentación que mide estos fenómenos, y (d) una intervención que permite tratar los casos problemáticos. Este artícul...

Modeling of TiAl Alloy Grating by Investment Casting

Directory of Open Access Journals (Sweden)

Yi Jia

2015-12-01

Full Text Available The investment casting of TiAl alloys has become the most promising cost-effective technique for manufacturing TiAl components. This study aimed to investigate a series of problems associated with the investment casting of TiAl alloys. The mold filling and solidification of this casting model were numerically simulated using ProCAST. Shrinkage porosity was quantitatively predicted by a built-in feeding criterion. The results obtained from the numerical simulations were compared with experiments, which were carried out on Vacuum Skull Furnace using an investment block mold. The investment casting of TiAl grating was conducted for verifying the correctness and feasibility of the proposed method. The tensile test results indicated that, at room temperature, the tensile strength and elongation were approximately 675 MPa and 1.7%, respectively. The microstructure and mechanical property of the investment cast TiAl alloy were discussed.

An Analysis of Cost Premiums and Losses Associated with USAF Military Construction (MILCON)

Science.gov (United States)

2013-03-01

construction firms ( Molenaar et al. 1999). The design-build+ method is a form of DB which brings the contractor into the planning phase early to help...of firm fixed prices requires the contractor to commit to a set price early in the design process ( Molenaar et al. 1999). Both firm fixed and cost...Research The performance of MILCON projects based on execution method has been investigated in terms of cost, performance, and schedule. Molenaar

Cost-Effective Powder Metallurgy TiAl-Based Components For Aerospace Use, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Gamma titanium aluminide (TiAl) alloys with their low density (~3.9g/cm3), good elevated temperature strength, stiffness, creep resistance and acceptable burn and...

Superhydrophobic ZnAl double hydroxide nanostructures and ZnO films on Al and glass substrates

Energy Technology Data Exchange (ETDEWEB)

De, Debasis, E-mail: debasis.de@bcrec.ac.in [Electronics and Instrumentation Engineering Department, Dr. B C Roy Engineering College, Durgapur, West Bengal 713206 (India); Sarkar, D.K. [Centre Universitaire de Recherche sur l' Aluminium (CURAL), L' Université du Québec à Chicoutimi, 555 Blvd. Université, Chicoutimi, Saguenay, Québec G7H 2B1 (Canada)

2017-01-01

Superhydrophobic nanostructured ZnAl: layered double hydroxides (LDHs) and ZnO films have been fabricated on Al and glass substrates, respectively, by a simple and cost effective chemical bath deposition technique. Randomly oriented hexagonal patterned of ZnAl: LDHs thin nanoplates are clearly observed on Al-substrate in the scanning electron microscopic images. The average size of these hexagonal plates is ∼4 μm side and ∼30 nm of thickness. While on the glass substrate, a oriented hexagonal patterned ZnO nanorods (height ∼5 μm and 1 μm diameter) are observed and each rod is further decorated throughout the top few nanometers with several nanosteps. At the top of the nanorod, a perfectly hexagonal patterned ZnO surface with ∼250 nm sides is observed. The tendency to form hexagonal morphological features is due to the hexagonal crystal structure of ZnO confirmed from X-ray diffraction patterns and transmission electron microscopy image. The ZnAl: LDHs and/or ZnO coated substrates have been passivated by using stearic acid (SA) molecules. Infrared spectra of passivated ZnAl: LDHs coated substrates confirm the presence of SA. X-ray diffraction pattern also corroborates the results of infrared spectrum. The contact angle of the as prepared samples is zero. The superhydrophobicity is achieved by observing contact angle of ∼161° with a hysteresis of ∼4° for Al-substrate. On the glass substrate, a higher contact angle of ∼168° with a lower hysteresis of ∼3° is observed. A lower surface roughness of ∼4.93 μm is measured on ZnAl: LDHs surface layer on the Al substrate as compare to a higher surface roughness of 6.87 μm measured on ZnO layer on glass substrate. The superhydrophobicity of passivated nanostructured films on two different substrates is observed due to high surface roughness and low surface energy. - Highlights: • ZnAl: layered double hydroxides (LDHs) nanoplates are fabricated on Al substrate. • ZnO nanorods are fabricated on

Plan de negocio agencia de marketing digital

OpenAIRE

Menéndez Díaz, Borja

2015-01-01

Con la realización de este plan de negocio, se tratará de estudiar la viabilidad para la puesta en marcha de una empresa dedicada al marketing digital, especializándose en el sector sanitario y fijándose como clientes potenciales todas aquellas empresas farmacéuticas en el ámbito nacional. La empresa pretende hacer marketing digital orientado al sector farmacéutico siguiendo unos procesos rigurosos y estandarizados con los que el cliente esté acorde en todo momento, manteniendo una actitud...

La institución matrimonial después del matrimonio homosexual

OpenAIRE

Beatriz Gimeno; Violeta Barrientos

2009-01-01

Este artículo sostiene la idea de que el reconocimiento del matrimonio homosexual –frente a otro tipo de iniciativas–, conseguido por el movimiento LGTB español en ese país, constituye una reforma no reformista. Es decir, antes que una reivindicación conservadora, que actualiza los sentidos naturalizados en el matrimonio al imponerlos a nuevos sujetos (homosexuales), constituye un mecanismo hacia su des-institucionalización. Se trataría de una reivindicación que al tiempo que afirma la plena...

Transaction costs of raising energy efficiency. Working paper

Energy Technology Data Exchange (ETDEWEB)

Ostertag, K. [Fraunhofer-Institut fuer Systemtechnik und Innovationsforschung (ISI), Karlsruhe (Germany); Centre International de Recherche sur l' Environnement et le Developpement (CIRED), 94 - Nogent sur Marne (France)

1999-05-01

In the face of the uncertainties concerning the importance and the actual impacts of anthropogeneous climate change the extent to which measures should be adopted to avoid greenhouse gas emissions (GHG) already today and in the near future is highly controversial. More specifically, part of the debate evolves around the existence and importance of energy saving potentials to reduce CO{sub 2} emissions that may be available at negative net costs, implying that the energy cost savings of one specific technology can actually more than offset the costs of investing into this technology and of using it. This so called 'no-regret' potential would comprise measures that from a pure economic efficiency point of view would be 'worth undertaking whether or not there are climate-related reasons for doing so' (Bruce et al. 1996, p. 271). The existence of the no-regret potential is often denied by arguing, that the economic evaluation of the energy saving potentials did not take into account transaction costs (Grubb et al. 1993). This paper will examine in more detail the concept of transaction costs as it is used in the current debate on no-regret potentials (section 1). Four practical examples are presented to illustrate how transaction costs and their determinants can be identified, measured and possibly influenced (section 2). In order to link the presented cases to modelling based evaluation approaches the implications for cost evaluations of energy saving measures especially in the context of energy system modelling will be shown (section 3). (orig.)

Manejo de lesiones dermatológicas virales desde atención primaria

Directory of Open Access Journals (Sweden)

M. Artieda Lanas

2001-01-01

Conclusiones: No hay datos concluyentes en la bibliografía referentes a la elección de la técnica para tratar estas lesiones. Recomendamos la crioterapia en lesiones múltiples y en zonas donde la cirugía pueda tener repercusión funcional. El curetaje parece eficaz para el Molluscum contagiosum y en resistencias al tratamiento médico.

Fabrication of Ti-0.48Al Alloy by Centrifugal Casting.

Science.gov (United States)

Park, Jong Bum; Lee, Jung-Il; Ryu, Jeong Ho

2018-09-01

Many of the unique properties of TiAl alloys that make are attractive for use in high-temperature structural applications also make it challenging to process them into useful products. Cast TiAl is rapidly nearing commercialization, particularly in the vehicle industry, owing to its low production cost. In this study, the centrifugal casting of a TiAl (Ti-48%Al, mole fraction) turbocharger was simulated and an experimental casting was created in vacuum using an induction melting furnace coupled to a ceramic composite mold. Numerical simulation results agreed with the experiment. The crystal structure, microstructure, and chemical composition of the TiAl prepared by centrifugal casting were studied by X-ray diffractometry, optical microscopy, field emission scanning electron microscopy (FE-SEM) and energy dispersive spectroscopy (EDS). FE-SEM and EDS examinations of the TiAl casting revealed that the thickness of the oxide layer (α-case) was typically less than 35 μm.

Evaluating effectiveness and cost of time-lapse triggered camera trapping techniques to detect terrestrial squamate diversity

Science.gov (United States)

Connor S. Adams; Wade A. Ryberg; Toby J. Hibbitts; Brian L. Pierce; Josh B. Pierce; D. Craig Rudolph

2017-01-01

Recent advancements in camera trap technology have allowed researchers to explore methodologies that are minimally invasive, and both time and cost efficient (Long et al. 2008; O’Connell et al. 2010; Gregory et al. 2014; Meek et al. 2014; Swinnen et al. 2014; Newey et al. 2015). The use of cameras for understanding the distribution and ecology of mammals is advanced;...

Costos de la atención médica atribuibles al consumo de tabaco en el Instituto Mexicano del Seguro Social Health care costs attributable to tobacco consumption on a national level in the Mexican Social Security Institute

Directory of Open Access Journals (Sweden)

Luz Myriam Reynales-Shigematsu

2006-01-01

Full Text Available OBJETIVO: Cuantificar el efecto de las enfermedades atribuibles al consumo de tabaco, en términos epidemiológicos (morbilidad y económicos (costos de atención médica, en el Instituto Mexicano del Seguro Social (IMSS a escala nacional. MATERIAL Y MÉTODOS: Los costos de la atención médica se estimaron desde la perspectiva del proveedor y se empleó la metodología del costeo de enfermedad. A partir de una muestra de pacientes (n= 1 596 atendidos en las unidades médicas se estableció la frecuencia de utilización de servicios en los tres niveles de atención. Para cada enfermedad se consideraron costos promedio por paciente y costos totales de enfermedad, los cuales se mensuraron en pesos mexicanos de 2004. Se calculó la fracción atribuible al consumo de tabaco para cada enfermedad, misma que se usó para atribuir los costos al tabaco. RESULTADOS: Los costos totales anuales de atención médica nacional corresponden a 7 114 millones para el infarto agudo del miocardio, 3 424 millones para la enfermedad vascular cerebral, 1 469 millones para la enfermedad pulmonar obstructiva crónica y 102 millones para el cáncer pulmonar. El costo total anual para el IMSS por estas cuatro enfermedades asciende a 12 100 millones de pesos. Los costos atribuibles al consumo de tabaco corresponden a 7 100 millones de pesos, lo cual equivale a 4.3% del gasto de operación de la institución en el año 2004. CONCLUSIONES: Estos resultados confirman el elevado costo de la atención médica de las enfermedades atribuibles al consumo de tabaco en el IMSS y generan información de primera mano necesaria para impulsar las medidas de prevención en esa institución y reforzar las políticas de control del tabaquismo ya aplicadas en México.OBJECTIVE: To estimate the cost of medical care for the major diseases attributable to tobacco consumption at the IMSS. MATERIAL AND METODS: A cost of illness (COI analysis was carried out from the perspective of the health

Influence of Iron in AlSi10MgMn Alloy

Directory of Open Access Journals (Sweden)

Žihalová M.

2014-12-01

Full Text Available Presence of iron in Al-Si cast alloys is common problem mainly in secondary (recycled aluminium alloys. Better understanding of iron influence in this kind of alloys can lead to reduction of final castings cost. Presented article deals with examination of detrimental iron effect in AlSi10MgMn cast alloy. Microstructural analysis and ultimate tensile strength testing were used to consider influence of iron to microstructure and mechanical properties of selected alloy.

76 FR 14570 - Federal Acquisition Regulation; Disclosure and Consistency of Cost Accounting Practices for...

Science.gov (United States)

2011-03-16

...] RIN 9000-AL58 Federal Acquisition Regulation; Disclosure and Consistency of Cost Accounting Practices... Regulation (FAR) to align it with a Cost Accounting Standards (CAS) Board clause, Disclosure and Consistency... the use of the clause, Disclosure and Consistency of Cost Accounting Practices--Foreign Concerns, in...

Costos del tratamiento de las telangiectasias y várices tronculares con escleroterapia con espuma en el Hospital "Freyre de Andrade" de La Habana Cost of the treatment of t elangiectases and varicose veins with foam sclerotherapy in ¨Freyre de Andrade¨hospital in Havana

Directory of Open Access Journals (Sweden)

Anai García Fariñas

2013-03-01

Full Text Available Objetivo: determinar cuánto cuesta por paciente el tratamiento de várices por la técnica de escleroterapia con espuma en la consulta externa de Angiología y Cirugía Vascular del Hospital C.Q. "Freyre de Andrade". Método: evaluación económica del tipo descripción de costo. Se estudió el costo directo institucional del tratamiento ambulatorio para várices en extremidades inferiores con escleroterapia con espuma y donde el principio activo fue Polidocanol al 0,5% a una dosis de 2ml. Se emplearon las partidas recursos humanos, material gastable y medicamento. Se determinó el costo promedio por paciente, total y según tipo de consulta. Resultados: el costo total por paciente atendido fue de 68,60 pesos cubanos. El costo medio por paciente de la consulta de clasificación fue de 0,18 centavos de pesos cubanos (DS 95%= 0,12. El costo medio de la consulta de tratamiento fue de 50,60 pesos cubanos (DS 95%=7,65. No hubo diferencias significativas entre los diferentes tipos de varices a tratar. Conclusiones: el costo directo institucional del tratamiento de telangiectasias y varices tronculares con escleroterapia con espuma fue similar. A corto plazo, el tratamiento de las várices con escleroterapia con espuma genera menores costos que la opción quirúrgica.Objective: to determine the cost of the treatment of varicose veins per patient with the foam sclerotherapy in the angiology and vascular surgery outpatient service of ¨Freyre de Andrade¨ clinical and surgical hospital. Method: a cost description-type economic assessment. The institutional direct cost of the leg varicose veins treatment with foam sclerotherapy at the outpatient service, using the active principle called 0.5% polidocanol at a dose of 2 ml, was studied. The variables were human resources, disposable materials and drugs. The average cost per patient, the total cost and type of service-depending cost were all estimated. Results: the total cost per patient was 68.60 Cuban

Cultural Differences in Opportunity Cost Consideration.

Science.gov (United States)

Zhang, Ning; Ji, Li-Jun; Li, Ye

2017-01-01

Two studies were conducted to investigate cultural differences in opportunity cost consideration between Chinese and Euro-Canadians. Opportunity cost is defined as the cost of a benefit that must be forgone in order to pursue a better alternative (Becker et al., 1974). In both studies, participants read about hypothetical purchase scenarios, and then decided whether they would buy a certain product. Opportunity cost consideration was measured in two ways: (1) participants' thoughts pertaining to other (nonfocal) products while making decisions; (2) participants' decisions not to buy a focal product (Study 1) or a more expensive product (Study 2). Across both indexes, we found that after controlling for individual difference variables and amount of pocket money, Chinese participants in China considered financial opportunity cost more than Euro-Canadians in Study 1. Similar results were observed in Study 2 when comparing Chinese in Canada with Euro-Canadians However, the cultural effect on opportunity cost consideration was confounded by family income in Study 2. Implications for resource management, limitations of the current research and directions for future research are discussed.

Stem cells therapy for ALS.

Science.gov (United States)

Mazzini, Letizia; Vescovi, Angelo; Cantello, Roberto; Gelati, Maurizio; Vercelli, Alessandro

2016-01-01

Despite knowledge on the molecular basis of amyotrophic lateral sclerosis (ALS) having quickly progressed over the last few years, such discoveries have not yet translated into new therapeutics. With the advancement of stem cell technologies there is hope for stem cell therapeutics as novel treatments for ALS. We discuss in detail the therapeutic potential of different types of stem cells in preclinical and clinical works. Moreover, we address many open questions in clinical translation. SC therapy is a potentially promising new treatment for ALS and the need to better understand how to develop cell-based experimental treatments, and how to implement them in clinical trials, becomes more pressing. Mesenchymal stem cells and neural fetal stem cells have emerged as safe and potentially effective cell types, but there is a need to carry out appropriately designed experimental studies to verify their long-term safety and possibly efficacy. Moreover, the cost-benefit analysis of the results must take into account the quality of life of the patients as a major end point. It is our opinion that a multicenter international clinical program aime d at fine-tuning and coordinating transplantation procedures and protocols is mandatory.

LEAN HEALTHCARE SUPPLY CHAIN MANAGEMENT: MINIMIZING WASTE AND COSTS

Directory of Open Access Journals (Sweden)

Catia M L Machado

2014-12-01

Full Text Available The purpose of this research is to investigate the management models applied in the supply chain providing services in healthcare organizations, considering the lenses of lean. The aim of this is to develop a model of supply chain management focusing on the identification and minimization of waste, assisting in decision making and contributing to the quality of services and as a consequence the reduction of the costs involved in healthcare supply chain. The philosophies of continuous improvement and lean techniques have a role to play in helping healthcare to provide quality service and support to reduce costs in the current budget constraints. In the supply chain of hospitals the financial costs can be around 40% of its budget (MASOUMI et al. 2012; SOUZA et al., 2013. This article sheds light on the improvement in decision making and the effect of reducing costs in the healthcare supply chain. In this sense, the research intend to expand knowledge related to supply chain management in the area of ​​provision of healthcare services through the use of the philosophy of continuous improvement and lean principles, helping healthcare to provide quality service within their current budget constraints.

Reactive control processes contributing to residual switch cost and mixing cost across the adult lifespan.

Science.gov (United States)

Whitson, Lisa R; Karayanidis, Frini; Fulham, Ross; Provost, Alexander; Michie, Patricia T; Heathcote, Andrew; Hsieh, Shulan

2014-01-01

In task-switching paradigms, performance is better when repeating the same task than when alternating between tasks (switch cost) and when repeating a task alone rather than intermixed with another task (mixing cost). These costs remain even after extensive practice and when task cues enable advanced preparation (residual costs). Moreover, residual reaction time mixing cost has been consistently shown to increase with age. Residual switch and mixing costs modulate the amplitude of the stimulus-locked P3b. This mixing effect is disproportionately larger in older adults who also prepare more for and respond more cautiously on these "mixed" repeat trials (Karayanidis et al., 2011). In this paper, we analyze stimulus-locked and response-locked P3 and lateralized readiness potentials to identify whether residual switch and mixing cost arise from the need to control interference at the level of stimulus processing or response processing. Residual mixing cost was associated with control of stimulus-level interference, whereas residual switch cost was also associated with a delay in response selection. In older adults, the disproportionate increase in mixing cost was associated with greater interference at the level of decision-response mapping and response programming for repeat trials in mixed-task blocks. These findings suggest that older adults strategically recruit greater proactive and reactive control to overcome increased susceptibility to post-stimulus interference. This interpretation is consistent with recruitment of compensatory strategies to compensate for reduced repetition benefit rather than an overall decline on cognitive flexibility.

Supersonic Plasma Spray Deposition of CoNiCrAlY Coatings on Ti-6Al-4V Alloy

Science.gov (United States)

Caliari, F. R.; Miranda, F. S.; Reis, D. A. P.; Essiptchouk, A. M.; Filho, G. P.

2017-06-01

Plasma spray is a versatile technology used for production of environmental and thermal barrier coatings, mainly in the aerospace, gas turbine, and automotive industries, with potential application in the renewable energy industry. New plasma spray technologies have been developed recently to produce high-quality coatings as an alternative to the costly low-pressure plasma-spray process. In this work, we studied the properties of as-sprayed CoNiCrAlY coatings deposited on Ti-6Al-4V substrate with smooth surface ( R a = 0.8 μm) by means of a plasma torch operating in supersonic regime at atmospheric pressure. The CoNiCrAlY coatings were evaluated in terms of their surface roughness, microstructure, instrumented indentation, and phase content. Static and dynamic depositions were investigated to examine their effect on coating characteristics. Results show that the substrate surface velocity has a major influence on the coating properties. The sprayed CoNiCrAlY coatings exhibit low roughness ( R a of 5.7 μm), low porosity (0.8%), excellent mechanical properties ( H it = 6.1 GPa, E it = 155 GPa), and elevated interface toughness (2.4 MPa m1/2).

Derecho internacional, acuerdo humanitario y resolución pacífica del secuestro

OpenAIRE

Heyck Puyana, Caterina

2011-01-01

La presente obra expone, de forma crítica, el problema del secuestro, teniendo como modelo el caso colombiano. Sigue el método propuesto por el reconocido investigador para la paz, el noruego Johan Galtung, según el cual, para la resolución de un conflicto puede acudirse al sistema de análisis que tiene la ciencia médica para tratar una enfermedad. En este sentido, frente a lo que corresponde al diagnóstico del secuestro, se presenta su historia, las cifras, los datos oficiales, la realidad d...

Análisis de la estrategia de marketing del sector turístico. Estudio de un caso concreto: Centro de Turismo Rural Valdelavilla

OpenAIRE

Arnedo González, Alba María

2015-01-01

En este trabajo se va a tratar de analizar el sector turístico desde el punto de vista del marketing, haciendo alusión al turismo rural con un caso real de estudio. El objetivo general es el análisis de la estrategia de marketing que sigue el sector turístico rural, concretamente el Centro de Turismo Rural Valdelavilla. Dentro de este contexto, los propósitos marcados previamente fueron los siguientes: - Aproximación al sector del turismo. Es decir, delimitar el alcance del concepto,...

Orden monetario de las economías de mercado

Directory of Open Access Journals (Sweden)

Aglietta Michel

2002-08-01

Full Text Available Al explicar el mercado a partir de la institucióm monetaria y no al revés, como es la costumbre en los economistas, este articulo ofrece una nueva visión para comprender la naturaleza del dinero, las condiciones de la viabilidad de la sociedad de mercado, el origen y control de las crisis financieras y monetarias, y finalmente, tratar la independencia del Banco Central como una organización institucional particular que se propone para la regulacion del sistema cada día ás globalizado.

ORDEN MONETARIO DE LAS ECONOMÍAS DE MERCADO

Directory of Open Access Journals (Sweden)

Michel Aglietta

2002-06-01

Full Text Available Al explicar el mercado a partir de la institución monetaria y no al revés, como es costumbre en los economistas, este artículo ofrece una nueva visión para comprender la naturaleza del dinero, las condiciones de viabilidad de la sociedad de mercado, el origen y control de las crisis financieras y monetarias y finalmente, tratar la independencia del Banco Central como una organización institucional particular que se propone para la regulación del sistema cada día más globalizado.

Hacking y ciberdelito

OpenAIRE

Giménez Solano, Vicente Miguel

2011-01-01

Investigar el delito desde cualquier perspectiva es una tarea compleja; de eso no hay duda. Las dificultades que surgen al tratar de aplicar el método científico a la Delincuencia Transnacional y al Crimen Organizado en buena parte ya fueron establecidas en estudios anteriores, pero enfrentar este tipo de delincuencia a todo nivel es la tarea a la que se ve avocada le Ministerio Público por mandato constitucional y por disposición legal. Ahora bien el fenómeno descrito en los últimos tiemp...

In-situ alloyed LENS additively manufactured TiAl-Nb structure

CSIR Research Space (South Africa)

Tlotleng, Monnamme

2017-11-01

Full Text Available corporates are interested in developments that will lead to cost effective manufacturing technologies that are able to produce homogenous, defect free TiAl structures. Additive manufacturing is one promising technology hence it was explored here in studying...

Superbends expand the scope of Berkeley's ALS

International Nuclear Information System (INIS)

Robin, David S.; Robinson, Arthur L.; Tamura, Lori S.

2002-01-01

While the ALS has turned out to be a world-leader in providing beams of soft X-rays -- indeed, furnishing these beams remains its core mission -- there has nonetheless been a steadily growing demand from synchrotron radiation users for harder X-rays with higher photon energies. The clamor has been strongest from protein crystallographers whose seemingly insatiable appetite for solving structures of biological macromolecules could not be satisfied by the number of crystallography beamlines available worldwide. But how to provide these X-rays in a cost-effective way without disrupting the thriving research programs of the existing ALS users was the problem. Superconducting bend magnets (superbends) provided the answer for the ALS, which adopted a proposal to replace some of the normal combined-function (gradient) magnets in the curved arcs of the storage ring with superconducting dipoles that could generate higher magnetic fields and thus synchrotron light with a higher critical energy

Al-Qurû’ fi Al-Qur’an ‘Inda Al-Anbary fi Al-Adhdâd

Directory of Open Access Journals (Sweden)

Raushani Azza

2018-03-01

Full Text Available This study examines about the term al-Qurû in the Qur’an. Al-Qurû is one of the most popular discussions among muslim scholars and mufasir, both in terms of language and fiqh. However, there is a bate among muslim scholar and mufasir about the meaning of al-Qurû. It’s because al-Qurû is one of the sentence of al-Adhdâd wich has two meaning, especially in the Qur’an, namely haid (menstruation and thahr. One of the most popular muslim scholar who concern in Qur’an and Arabic is al-Anbari with his book al-Adhdâd. Al-Anbari explains that Qurû has two meanings, First, al-Qurû in etymology is the form of Jama’ from aqra and qurû. Second, al-Qurû has a meaning of menstruation, thahr, or the period of iddah as a sign of being allowed to remarry after certain period of time.

Idaaratu al Wahdah al Namthiyah li at Tathwiri al Tarbiyah al Islamiyah

Directory of Open Access Journals (Sweden)

Ahmad Danusiri

2016-04-01

Full Text Available Islam, through the Quran, proclaims that its mission includes the teachings to the whole universe, Everything in the universe is maintained by Islam, and none of the symptoms are ignored. The revelations also include the traditions of the Prophet that are authentic (shahih and good (hasan in quality. Both the Quran and maqbulah hadiths are accepted by Muslims on the basis of faith. When some experts of UIN Walisongo from various disciplines try to understand the sacred words of these two resources, their understanding continues, reaching the paradigm of the unity of science which essentially unites the normative, social, and natural sciences. The effect of this paradigm has brought up an issue for the author. Is there any hadiths or Prophetic traditions that can be used as a grand theory in the management disciplines of Islamic education.To address this issue, the authors conducted a literature research with the title Development of Islamic Education Management Module. Sources of data were focused on nine books of Hadiths : Sahih al-Bukhari, Sahih al-Muslim, Sunan Abu Dawud, Sunan at-Turmudzi, Sunan an-Nasai, Sunan Ibn Majah, Sunan ad-Darimi, Muwatta Malik, and Musnad Imam Ahmad bin Hanbal in the form of digital data Lidwa Reader Software Book 9 Imam Hadith. The findings of the study stated that the meaning of the word Rabb includes: creating, nurturing, maintaining, teaching, educating, and organizing. Thus, in an academic term, the word Rabb implies a manager or leader. Meanwhile, in the concept of comprehensive manager it contains at least 14 nomenclature denotations: planning, responsibility, organization, coordination, system of employee payroll, learning, resources, humanity, principle of making it easier for the manager to the employee, motivated to achieve optimal performance, preventing unproductivity, education participation, institutional costs, monitoring, and evaluation system. Each nomenclature has numerous hadiths that could serve

Profile of medical care costs in patients with amyotrophic lateral sclerosis in the Medicare programme and under commercial insurance.

Science.gov (United States)

Meng, Lisa; Bian, Amy; Jordan, Scott; Wolff, Andrew; Shefner, Jeremy M; Andrews, Jinsy

2018-02-01

To determine amyotrophic lateral sclerosis (ALS)-associated costs incurred by patients covered by Medicare and/or commercial insurance before, during and after diagnosis and provide cost details. Costs were calculated from the Medicare Standard Analytical File 5% sample claims data from Parts A and B from 2009, 2010 and 2011 for ALS Medicare patients aged ≥70 years (monthly costs) and ≥65 years (costs associated with disability milestones). Commercial insurance patients aged 18-63 years were selected based on the data provided in the Coordination of Benefits field from Truven MarketScan® in 2008-2010. Monthly costs increased nine months before diagnosis, peaked during the index month (Medicare: $10,398; commercial: $9354) and decreased but remained high post-index. Costs generally shifted from outpatient to inpatient and private nursing after diagnosis; prescriptions and durable medical equipment costs were much higher for commercial patients post-diagnosis. Patients appeared to progress to disability milestones more rapidly as their disease progressed in severity (14.4 months to non-invasive ventilation [NIV] vs. 16.6 months to hospice), and their costs increased accordingly (NIV: $58,973 vs. hospice: $76,179). For newly diagnosed ALS patients in the U.S., medical costs are substantial and increase rapidly and substantially with each disability milestone.

Esplenectomia parcial para tratar hemangioma esplênico

Directory of Open Access Journals (Sweden)

Andy Petroianu

Full Text Available Apesar de a esplenectomia ser eficaz na abordagem terapêutica de pacientes com hemangioma esplênico, esse procedimento é acompanhado de elevada morbidade e até mortalidade, principalmente devido à sepse, quando realizado em crianças e adolescentes com sistema imunitário ainda imaturo. Para prevenir os efeitos adversos da asplenia, propõe-se neste artigo a esplenectomia parcial, com a retirada apenas da região do hemangioma, mantendo o restante do baço e preservando suas importantes funções.

Estimating the burden of smoking: premature mortality, morbidity, and costs Estimaciones de la carga debido al consumo de tabaco: mortalidad, morbilidad prematura, y costo

Directory of Open Access Journals (Sweden)

Jonathan M Samet

2010-01-01

Full Text Available Estimation of the burden of disease attributable to smoking has now become standard in documenting the impact of the tobacco epidemic and in motivating tobacco control. This paper addresses the methods used to estimate the attributable burden of mortality and the related estimation of morbidity and economic costs. Estimates of attributable mortality and morbidity for the Americas range widely, reflecting the maturity of the tobacco epidemic. The estimates are highest for the United States, and lower for Mexico and other countries of the Americas.La medida del impacto de la epidemia de tabaquismo y la promoción del control del tabaco ha sido el estándar para estimar la carga total de enfermedades atribuible al consumo de tabaco. Este artículo estudia los métodos usados para estimar la mortalidad atribuible al consumo de tabaco, así como su morbilidad y los costos económicos. La mortalidad y morbilidad atribuible para la población de los Estados Unidos varía ampliamente, lo que refleja la madurez de la epidemia de tabaquismo. Las estimaciones para los Estados Unidos son altas, y más bajas para México y otros países de América.

Al-Âyah al-Mutasyâbihât al-Lafzhiyyah fi Sûrah al-An’âm ‘Inda al-Kirmâny

Directory of Open Access Journals (Sweden)

Hikmatiar Pasya

2017-07-01

Full Text Available This paper discusses about the verses of mutasyâbihât in the Quran. The debate of this verses caused various opinions. The meaning of the mutasyâbihât in this paper is the similarity and difference of the words in the Qur'an. Mufasir have different opinion about the meaning of the verse of mutasyâbihât al-lafdzi. In addition, many Hufadz of the Quran who are confused from one verse to another, or one chapter to another. It’s because similarity of verses in the Qur'an with other verses. So the writer wants to explain the verses mutasyâbihât al-lafdzi in the perspective of Hamzh al-Karmani in Surah al-An'âm. In this discussion the author discovers some passages in mutasyâbihât al-lafdzi, namely Asrâru al-balaghah fi mutasyabih al-lafdzi, Asrar al-balaghah fi mutasyabih al-hurf, and murâ'ah al-ikhtilâfmurâd bi al-lafdzi al-mukarrar.

Impact of an AlAs window layer upon the optical properties of Al x Ga1-x As photodiodes

Science.gov (United States)

Kang, T.; Chen, X. J.; Johnson, E. B.; Christian, J. F.; Lee, K.; Hammig, M. D.

2016-05-01

Recently developed advanced scintillators, which have the ability to distinguish gamma-ray interaction events from those that accompany neutron impact, require improved quantum efficiency in the blue to near UV region of the spectrum. We utilize GaAs/Al0.8Ga0.2As photodiode elements as components in a wide band-gap solid-state photomultiplier as a lower-cost, lower logistical burden, and higher quantum efficiency replacement for the photomultiplier tube. An AlAs window layer is employed as a means to increase the diode’s optical performance. Relative to structures absent the window layer, simulations and measurements demonstrate that the AlAs layer produces a spatial coincidence between regions of large drift fields with regions of high photon absorption. In addition to the AlAs layer, secondary ion mass spectrometry measurements show that an unexpected high degree of inter-diffusion of GaAs and AlAs quenches the photon-detection efficiency, a decrease that can be avoided by its post-growth removal. With the AlAs layer, the peak external quantum efficiency of 49% is achieved at 450 nm with 10 V reverse bias, which does not fully deplete the device. Simulations show that full depletion can result in efficiencies exceeding 90%. In order to enhance the optical response, a simple anti-reflective coating layer is designed using the existing passivation layer components that successfully minimizes the reflection at the wavelength range of interest (300 nm-500 nm).

What Are the Costs of Degraded Parafoveal Previews during Silent Reading?

Science.gov (United States)

Vasilev, Martin R.; Slattery, Timothy J.; Kirkby, Julie A.; Angele, Bernhard

2018-01-01

It has been suggested that the preview benefit effect is actually a combination of preview benefit and preview costs. Marx et al. (2015) proposed that visually degrading the parafoveal preview reduces the costs associated with traditional parafoveal letter masks used in the boundary paradigm (Rayner, 1975), thus leading to a more neutral baseline.…

Costs of food waste along the value chain: evidence from South Africa

CSIR Research Space (South Africa)

Nahman, Anton

2013-11-01

Full Text Available In a previous paper (Nahman et al., 2012), the authors estimated the costs of household food waste in South Africa, based on the market value of the wasted food, as well as the costs of disposal to landfill. In this paper, we extend the analysis...

Taming the Hurricane of Acquisition Cost Growth - Or at Least Predicting It

Science.gov (United States)

2015-01-01

the practice of generating two different cost estimates dubbed Will Cost and Should Cost. The Should Cost estimate is “based on realistic tech...to predict estimate error in similar future programs. This method is dubbed “macro-stochastic” estimation (Ryan, Schubert Kabban, Jacques...mph Potential Day 1-3 Track Area Tropical Storm Warning OK AR TN AL FL Mexico MS LA TX 30 N 35 N 25 N 95 W 90 W 85 W 80 W True at 30.00N Approx

Efectos de los costes de cambio y de retención sobre el bienestar social en el servicio postal europeo

Directory of Open Access Journals (Sweden)

A. Javier Prado Domínguez

2014-01-01

Full Text Available Una política que fortalece la competencia a largo plazo en el sector postal es la actuación sobre los costes de cambio y de retención. En dos escenarios de duopolio, uno con costes de cambio y otro con costes de cambio y costes de retención, el objetivo del presente trabajo es descubrir en qué medida la variación de los costes de cambio de proveedor y de los costes de retención afectan al excedente del consumidor y al beneficio de las dos firmas y, en consecuencia, al bienestar social. Se desarrolla una ampliación propia del modelo seminal de Klemperer, que incorpora los costes de retención. La metodología consiste en la determinación y comparación de las situaciones del equilibrio Cournot-Nash. Los resultados obtenidos muestran la importancia de las políticas orientadas a la reducción de los costes de cambio de proveedor como una de las políticas que fortalecen la competencia a largo plazo en un servicio de interés general, como es el servicio postal.

Cost and energy consumption estimates for the aluminum-air battery anode fuel cycle

Science.gov (United States)

1990-01-01

At the request of DOE's Office of Energy Storage and Distribution (OESD), Pacific Northwest Laboratory (PNL) conducted a study to generate estimates of the energy use and costs associated with the aluminum anode fuel cycle of the aluminum-air (Al-air) battery. The results of this analysis indicate that the cost and energy consumption characteristics of the mechanically rechargeable Al-air battery system are not as attractive as some other electrically rechargeable electric vehicle battery systems being developed by OESD. However, there are distinct advantages to mechanically rechargeable batteries, which may make the Al-air battery (or other mechanically rechargeable batteries) attractive for other uses, such as stand-alone applications. Fuel cells, such as the proton exchange membrane (PEM), and advanced secondary batteries may be better suited to electric vehicle applications.

Cost Analysis of Noninvasive Helmet Ventilation Compared with Use of Noninvasive Face Mask in ARDS

Directory of Open Access Journals (Sweden)

Kwadwo Kyeremanteng

2018-01-01

Full Text Available Intensive care unit (ICU costs have doubled since 2000, totalling 108 billion dollars per year. Acute respiratory distress syndrome (ARDS has a prevalence of 10.4% and a 28-day mortality of 34.8%. Noninvasive ventilation (NIV is used in up to 30% of cases. A recent randomized controlled trial by Patel et al. (2016 showed lower intubation rates and 90-day mortality when comparing helmet to face mask NIV in ARDS. The population in the Patel et al. trial was used for cost analysis in this study. Projections of cost savings showed a decrease in ICU costs by $2527 and hospital costs by $3103 per patient, along with a 43.3% absolute reduction in intubation rates. Sensitivity analysis showed consistent cost reductions. Projected annual cost savings, assuming the current prevalence of ARDS, were $237538 in ICU costs and $291682 in hospital costs. At a national level, using yearly incidence of ARDS cases in American ICUs, this represents $449 million in savings. Helmet NIV, compared to face mask NIV, in nonintubated patients with ARDS, reduces ICU and hospital direct-variable costs along with intubation rates, LOS, and mortality. A large-scale cost-effectiveness analysis is needed to validate the findings.

Heterogeneous nucleation of solid Al from the melt by TiB2 and Al3Ti: An ab initio molecular dynamics study

KAUST Repository

Wang, Junsheng; Horsfield, Andrew; Lee, Peter D.; Schwingenschlö gl, Udo

2010-01-01

The nucleation of solid Al from the melt by TiB2 is well established and is believed to involve the formation of Al3Ti. Since the atomic-scale mechanisms involved are not fully understood, we look to computer simulation to provide insight. As there is an absence of suitable potentials for all of this complex system we have performed large-scale density-functional-theory molecular dynamics simulations of the nucleation of solid Al from the melt on TiB2 and Al3Ti substrates at undercoolings of around 2 K. Using periodic boundary conditions, we find limited ordering and no signs of incipient growth in the liquid Al close to the B-terminated surface of TiB2. By contrast, we see fcc-like ordering near the Ti-terminated surface, with growth being frustrated by the lattice mismatch between bulk Al and the TiB2 substrate. The Al interatomic distances at the Ti-terminated surface are similar to distances found in Al3Ti; we suggest that the layer encasing TiB2 observed experimentally may be strained Al on a Ti-terminated surface rather than Al3Ti. For the Al3Ti substrate, fcc-like structures are observed on both sides which extend rapidly into the melt. Periodic boundaries introduce unphysical stresses which we removed by introducing a vacuum region to separate the liquid from the solid at one of the interfaces. We see ordering in the Al on both the B-terminated (0001) surface of TiB2, and on Al3Ti(112), with the ordering able to be stronger on the Al3Ti substrate. However, we cannot draw strong conclusions as these simulations need more time to allow long-ranged fluctuations in the liquid Al to dampen out. The huge computational cost restricted the range and duration of simulations that was possible.

Heterogeneous nucleation of solid Al from the melt by TiB2 and Al3Ti: An ab initio molecular dynamics study

KAUST Repository

Wang, Junsheng

2010-11-16

The nucleation of solid Al from the melt by TiB2 is well established and is believed to involve the formation of Al3Ti. Since the atomic-scale mechanisms involved are not fully understood, we look to computer simulation to provide insight. As there is an absence of suitable potentials for all of this complex system we have performed large-scale density-functional-theory molecular dynamics simulations of the nucleation of solid Al from the melt on TiB2 and Al3Ti substrates at undercoolings of around 2 K. Using periodic boundary conditions, we find limited ordering and no signs of incipient growth in the liquid Al close to the B-terminated surface of TiB2. By contrast, we see fcc-like ordering near the Ti-terminated surface, with growth being frustrated by the lattice mismatch between bulk Al and the TiB2 substrate. The Al interatomic distances at the Ti-terminated surface are similar to distances found in Al3Ti; we suggest that the layer encasing TiB2 observed experimentally may be strained Al on a Ti-terminated surface rather than Al3Ti. For the Al3Ti substrate, fcc-like structures are observed on both sides which extend rapidly into the melt. Periodic boundaries introduce unphysical stresses which we removed by introducing a vacuum region to separate the liquid from the solid at one of the interfaces. We see ordering in the Al on both the B-terminated (0001) surface of TiB2, and on Al3Ti(112), with the ordering able to be stronger on the Al3Ti substrate. However, we cannot draw strong conclusions as these simulations need more time to allow long-ranged fluctuations in the liquid Al to dampen out. The huge computational cost restricted the range and duration of simulations that was possible.

Low cost AB{sub 5}-type hydrogen storage alloys for a nickel-metal hydride battery

Energy Technology Data Exchange (ETDEWEB)

Jiang Lijun [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Zhan Feng [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Bao Deyou [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Qing Guangrong [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Li Yaoquan [General Res. Inst. for Non-Ferrous Metals, Beijing (China); Wei Xiuying [General Res. Inst. for Non-Ferrous Metals, Beijing (China)

1995-12-15

The studies have been carried out on utilizing Ml(NiAl){sub 5}-based alloys as a low cost negative battery electrode. The replacement of nickel by copper improved the cycle lifetime to some extent without a decrease in capacity. Using Ml(NiAlCu){sub 5} alloys, hydrogen storage alloys with good overall characteristics and low cost were obtained through substituting cobalt or silicon for nickel. The discharge capacity was further increased by increasing the lanthanum content in lanthanum-rich mischmetal. (orig.)

Diffusion-induced quadrupole relaxation of 27Al nuclei in dilute Al-Ti, Al-Cr, Al-Mn, and Al-Cu alloys at high temperatures

International Nuclear Information System (INIS)

Bottyan, L.; Beke, D.L.; Tompa, K.

1983-01-01

The temperature dependence of the laboratory frame spin-lattice relaxation time of 27 Al nuclei is measured in 5N Al and in dilute Al-Ti, Al-Cr, Al-Mn, and Al-Cu alloys at 5.7 and 9.7 MHz resonance frequencies. The relaxation in pure aluminium is found to be purely due to the conduction electrons. An excess T 1 -relaxation contribution is detected in all Al-3d alloys investigated above 670 K. The excess relaxation rate is proportional to the impurity content and the temperature dependence of the excess contribution is of Arrhenius-type with an activation energy of (1.3 +- 0.3) eV for all of the investigated alloys. The relaxation contribution is found to be quadrupolar in origin and is caused by the relative diffusional jumps of solute atoms and Al atoms relatively far from the impurity. (author)

Interfacial phenomena in the reactions of Al-B, Al-Ti-B, and Al-Zr-B alloys with KF-AlF3 and NaF-AlF3 melts

International Nuclear Information System (INIS)

Lee, M.S.; Terry, B.S.; Grieveson, P.

1993-01-01

The interfacial phenomena occurring during the contacting of liquid Al-B, Al-Ti-B, and Al-Zr-B melts with KF-AlF 3 liquid fluxes have been investigated by optical examination of quenched metal drops previously immersed in the liquid fluxes. Reactions in the Al-B/KF-AlF 3 system involve the formation of metastable AlB 12 at the metal/flux interface. At high KBF 4 levels in the flux, the AlB 12 is dispersed in the flux and also at low KBF 4 levels in the metal. Reactions in the Al-Ti-B/KF-AlF 3 system involve the formation of TiB 2 , which may be dispersed in either the metal or the flux depending upon the composition of the flux. The results obtained for the Al-Ti-B/NaF-AlF 3 and Al-Zr-B/KF-AlF 3 systems were similar to those observed for the Al-Ti-B/KF-AlF 3 system

El cuerpo del niño como trastorno: aproximaciones discursivas al abordaje del TDAH

OpenAIRE

Ceardi, Andrea; Améstica, José; Núñez, Carmen; López, Verónica; López, Valeska; Gajardo, Julio

2016-01-01

El Trastorno de Déficit Atencional con Hiperactividad (TDAH) es el diagnóstico neurológico más frecuente en niños en edad escolar atendidos en el servicio de atención primaria en Chile. Se han implementado nuevas regulaciones que definen cuáles profesionales pueden diagnosticar y tratar el trastorno. En este estudio nos aproximamos a la construcción del TDAH desde una perspectiva discursiva, a través del análisis de entrevistas a padres, profesionales de las áreas de la salud y educación enca...

El cuerpo del niño como trastorno : aproximaciones discursivas al abordaje del TDAH

OpenAIRE

Ceardi Marambio, Andrea

2016-01-01

El Trastorno de Déficit Atencional con Hiperactividad (TDAH) es el diagnóstico neurológico más frecuente en niños en edad escolar atendidos en el servicio de atención primaria en Chile. Se han implementado nuevas regulaciones que definen cuáles profesionales pueden diagnosticar y tratar el trastorno. En este estudio nos aproximamos a la construcción del TDAH desde una perspectiva discursiva, a través del análisis de entrevistas a padres, profesionales de las áreas de la salud y educación enca...

Morbilidad, mortalidad y costes sanitarios evitables mediante una estrategia de tratamiento del tabaquismo en España

Directory of Open Access Journals (Sweden)

González-Enríquez J.

2002-01-01

Full Text Available Objetivo: Se valoran los efectos que tendría una intervención destinada a reducir el uso de tabaco en la población española de fumadores sobre la morbilidad, la mortalidad y los costes asociados al consumo de tabaco. Método: Se ha adaptado el modelo Health and Economic Consequences of Smoking patrocinado por la OMS y desarrollado por The Lewin Group. La intervención propuesta incluye el acceso a asistencia farmacológica de un 35% de los fumadores que intentan dejar de fumar, y obtienen una tasa global de cesación al año del 7,2%. Las enfermedades estudiadas son: cáncer de pulmón, enfermedad coronaria, enfermedad cerebrovascular, EPOC, asma y bajo peso al nacer. Se estiman los casos de enfermedad y muerte atribuibles al consumo de tabaco evitados y la reducción en el coste sanitario debidos a la intervención, proyectados a 20 años. Resultados: Sin intervención, en el año 1 del modelo 2.136.094 fumadores padecen alguna de las condiciones clínicas atribuibles al consumo de tabaco, el coste asistencial es de 4.286 millones de euros y las muertes atribuibles son 26.537. La intervención propuesta evita 2.613, 9.192, 17.415 y 23.837 casos de enfermedad atribuible al consumo de tabaco en los años 2, 5, 10 y 20 del modelo, respectivamente. Los costes asistenciales acumulados evitados son 3,5 millones de euros en el año 2 y 386 millones de euros a los 20 años. Las muertes acumuladas evitadas son 284 en el año 2 y 9.205 a los 20 años de la intervención. La intervención añade un total de 78.173 años de vida al final del período considerado. Conclusiones: La disponibilidad de nuevas intervenciones eficaces en el tratamiento del tabaquismo y el incremento de la accesibilidad a las mismas pueden contribuir de forma relevante a la reducción de la morbilidad, la mortalidad y los costes sanitarios asociados al tabaquismo en España.

Socio-Economic research on fusion SERF 3(2001-2003) External Costs of Fusion

International Nuclear Information System (INIS)

Lechon, Y.; Saez, R.; Cabal, H.

2003-01-01

Based on SEAFP project (Raeder et al, 1995) findings a preliminary assessment of environmental external costs associated to fusion power was performed under the framework of the first phase of the SERF (Socioeconomic Research on Fusion) project (Saez et al, 1999). This study showed very low external costs of fusion power compared with other traditional and new energy generating technologies. In order to update the assessment of externalities of fusion power, SERF2 project a new plant was included and an analysis of the key variables influencing the external cost was carried out. In the new phase of the SERF project, SERF3, three new additional plant models have been introduced with the aim of assessing the possibilities of silicon carbide to be used as structural material for fusion power plants. Furthermore, comparison of fusion external costs with those of other generation technologies in the state of technology development expected for 2050 has been also performed. (Author)

Microstructure and wear characteristics on Al alloy matrix composite reinforced with Ni perform

Energy Technology Data Exchange (ETDEWEB)

Park, Won Jo; Park, Cheol Hong; Kim, Hyung Jin; Huh, Sun Chul [Gyeongsang National University, Tongyeong, (Korea, Republic of)

2012-06-15

Al based composite reinforced with Nickel is used for diesel engine piston, because the thermal properties, strength and corrosion resistant are for better than Al alloy alone. For processing, the intermetallic compounds of Ni and Al improves wear resistance due to its high hardness. Existing process methods for MMC (metal matrix composite) using preform were manufactured under high-pressure. However, this causes deformation of the preform or weaknesses in the completed MMC. Low-pressure infiltration can prevent these problems, and there is an advantage of cost reduction in of production with small-scale of production equipment. In this study, the microstructure and wear characteristics of Al-based composite with Ni preform as reinforcement with low-pressure infiltration was analyzed.

La revolución de lxs “nada”: una aproximación al debate sobre orientación sexual, identidad de género y discriminación

Directory of Open Access Journals (Sweden)

Paula Viturro Mac Donald

2013-06-01

Full Text Available En un comienzo, el artículo da cuenta de los avances del sistema de protección de derechos humanos y de las legislaciones latinoamericanas en materia de discriminación por orientación sexual e identidad de género. Luego, da paso al análisis de los elementos de igualdad universal que debieran ser respetados en materia de orientación sexual e identidad de género. Considerando esto, se analizan tres dificultades que han existido para reconocer este deber. Primero, se revisan los límites que la modernidad ha puesto al concepto de “hombre”, que ha justificado a lo largo de la historia distintos tipos de discriminación a ciertos grupos. Segundo, las limitaciones que tiene el discurso jurídico, que si bien aparece como neutro, a la hora de tratar temas relativos a discriminación por orientación sexual se puede apreciar su inminente dimensión política. Tercero, se aborda la importancia que la justificación naturalista ha tenido en el tratamiento de decisiones judiciales de casos con titulares de derechos homosexuales, trans o travestis. Para finalmente dar cuenta de cuál sería el necesario paso final: saltar de una visión de patología a una en donde se reconozca la autonomía de las personas.

Removal of arsenic from drinking water by the electrocoagulation using Fe and Al electrodes

International Nuclear Information System (INIS)

Kobya, M.; Gebologlu, U.; Ulu, F.; Oncel, S.; Demirbas, E.

2011-01-01

Highlights: → Removal percentages of arsenic from drinking water at optimum operating conditions in electrocoagulation process were 93.5% for Fe electrode and 95.7% for Al electrode. → Operating costs at the optimum conditions were 0.020 Euro m -3 for Fe and 0.017 Euro m -3 for Al electrodes. → Surface topography of the solid particles at Fe/Al electrodes was analyzed with scanning electron microscope. → The adsorption of arsenic followed pseudo second-order adsorption model. - Abstract: A novel technique of electrocoagulation (EC) was attempted in the present investigation to remove arsenic from drinking waters. Experiments were carried out in a batch electrochemical reactor using Al and Fe electrodes with monopolar parallel electrode connection mode to assess their efficiency. The effects of several operating parameters on arsenic removal such as pH (4-9), current density (2.5-7.5 A m -2 ), initial concentration (75-500 μg L -1 ) and operating time (0-15 min) were examined. Optimum operating conditions were determined as an operating time of 12.5 min and pH 6.5 for Fe electrode (93.5%) and 15 min and pH 7 for Al electrode (95.7%) at 2.5 A m -2 , respectively. Arsenic removal obtained was highest with Al electrodes. Operating costs at the optimum conditions were calculated as 0.020 Euro m -3 for Fe and 0.017 Euro m -3 for Al electrodes. EC was able to bring down aqueous phase arsenic concentration to less than 10 μg L -1 with Fe and Al electrodes. The adsorption of arsenic over electrochemically produced hydroxides and metal oxide complexes was found to follow pseudo second-order adsorption model. Scanning electron microscopy was also used to analyze surface topography of the solid particles at Fe/Al electrodes during the EC process.

Removal of arsenic from drinking water by the electrocoagulation using Fe and Al electrodes

Energy Technology Data Exchange (ETDEWEB)

Kobya, M., E-mail: kobya@gyte.edu.tr [Gebze Institute of Technology, Department of Environmental Engineering, 41400 Gebze (Turkey); Gebologlu, U.; Ulu, F.; Oncel, S. [Gebze Institute of Technology, Department of Environmental Engineering, 41400 Gebze (Turkey); Demirbas, E. [Gebze Institute of Technology, Department of Chemistry, 41400 Gebze (Turkey)

2011-05-30

Highlights: > Removal percentages of arsenic from drinking water at optimum operating conditions in electrocoagulation process were 93.5% for Fe electrode and 95.7% for Al electrode. > Operating costs at the optimum conditions were 0.020 Euro m{sup -3} for Fe and 0.017 Euro m{sup -3} for Al electrodes. > Surface topography of the solid particles at Fe/Al electrodes was analyzed with scanning electron microscope. > The adsorption of arsenic followed pseudo second-order adsorption model. - Abstract: A novel technique of electrocoagulation (EC) was attempted in the present investigation to remove arsenic from drinking waters. Experiments were carried out in a batch electrochemical reactor using Al and Fe electrodes with monopolar parallel electrode connection mode to assess their efficiency. The effects of several operating parameters on arsenic removal such as pH (4-9), current density (2.5-7.5 A m{sup -2}), initial concentration (75-500 {mu}g L{sup -1}) and operating time (0-15 min) were examined. Optimum operating conditions were determined as an operating time of 12.5 min and pH 6.5 for Fe electrode (93.5%) and 15 min and pH 7 for Al electrode (95.7%) at 2.5 A m{sup -2}, respectively. Arsenic removal obtained was highest with Al electrodes. Operating costs at the optimum conditions were calculated as 0.020 Euro m{sup -3} for Fe and 0.017 Euro m{sup -3} for Al electrodes. EC was able to bring down aqueous phase arsenic concentration to less than 10 {mu}g L{sup -1} with Fe and Al electrodes. The adsorption of arsenic over electrochemically produced hydroxides and metal oxide complexes was found to follow pseudo second-order adsorption model. Scanning electron microscopy was also used to analyze surface topography of the solid particles at Fe/Al electrodes during the EC process.

The pressureless sintering and mechanical properties of AlON ceramic

Energy Technology Data Exchange (ETDEWEB)

Zhang, N., E-mail: zhangning5832@163.com [Key Lab. of Advanced Materials and Manufacturing Technology of Liaoning Province, Shenyang University, Shenyang, Liaoning 110044 (China); Liang, B.; Wang, X.Y.; Kan, H.M.; Zhu, K.W. [Key Lab. of Advanced Materials and Manufacturing Technology of Liaoning Province, Shenyang University, Shenyang, Liaoning 110044 (China); Zhao, X.J. [Department of Materials Science and Engineering, School of Materials and Metallurgy, Northeastern University, Shenyang, Liaoning 110004 (China)

2011-07-25

Highlights: {yields} A one-step pressureless sintering process was proposed, which is simple and viable. {yields} Cheap and easily available {alpha}-Al{sub 2}O{sub 3} and aluminum powders were chosen as raw materials substituting for expensive AlN ultrafine powders. {yields} The sintering temperature of AlON ceramic was reduced by 50 deg. C and the flexural strength was enhanced by 29.4%. - Abstract: Aluminum oxynitride (AlON) ceramic was synthesized by one-step pressureless sintering technology using low cost and easily available {alpha}-Al{sub 2}O{sub 3} and aluminum powders as raw materials. The sintering temperature was reduced because aluminum powders were nitridized into high activity AlN under the flowing nitrogen atmosphere. The curves of thermal analysis, microstructure and atomic distribution were investigated. The influence of sintering temperatures on phase composition, sintering densification and flexural strength was also explored. The experimental results showed that {alpha}-Al{sub 2}O{sub 3} and aluminum powders were acceptable substitutes for more expensive AlN ultrafine powders. Under the optimum sintering process at 1750 deg. C for 2 h, the sintered density and flexural strength of AlON ceramic were higher, 3.62 g/cm{sup 3} and 321 MPa, respectively. The sintering temperature was decreased by 50 deg. C because newly formed high activity AlN in situ reacted with Al{sub 2}O{sub 3} into Al{sub 23}O{sub 27}N{sub 5}, enhancing flexural strength by 29.4%. However, the sintering temperature could not be too high because grain growth and displacement of oxygen atoms from AlON ceramics by nitrogen atoms caused a decline in sintering densification and flexural strength.

Synthesizing (ZrAl3 + AlN)/Mg-Al composites by a 'matrix exchange' method

Science.gov (United States)

Gao, Tong; Li, Zengqiang; Hu, Kaiqi; Han, Mengxia; Liu, Xiangfa

2018-06-01

A method named 'matrix exchange' to synthesize ZrAl3 and AlN reinforced Mg-Al composite was developed in this paper. By inserting Al-10ZrN master alloy into Mg matrix and reheating the cooled ingot to 550 °C, Al and Mg atoms diffuse to the opposite side. As a result, liquid melt occurs once the interface areas reach to proper compositions. Then dissolved Al atoms react with ZrN, leading to the in-situ formation of ZrAl3 and AlN particles, while the Al matrix is finally replaced by Mg. This study provides a new insight for preparing Mg composites.

Cost of Capital Estimation for Highway Concessionaires in Chile

Directory of Open Access Journals (Sweden)

Cristian Vergara-Novoa

2018-01-01

Full Text Available In this paper, we present the cost of capital estimation for highway concessionaires in Chile. We estimated the cost of equity and the cost of debt and determined the capital structure for each one of twenty-four concessionaires that operate highways. We based our estimations on the developments of Sharpe (1964, Modigliani and Miller (1958, and Maquieira (2009, which were also compared with the Brusov et al. (2015 developments. We collected stock prices for different highway concessionaires around the world from Google Finance and Reuters’ websites in order to determine the Beta of equity using a representative company. After that, we estimated the cost of equity considering Hamada (1969 and a Capital Asset Pricing Model. Then, we estimated the cost of capital using the cost of debt and the capital structure of Chile’s highway concessionaires. With all above, we were able to determine the Weighted Average Cost of Capital (WACC for highway concessions which ranges from 5.49 to 6.62%.

Coupled growth of Al-Al2Cu eutectics in Al-Cu-Ag alloys

International Nuclear Information System (INIS)

Hecht, U; Witusiewicz, V; Drevermann, A

2012-01-01

Coupled eutectic growth of Al and Al 2 Cu was investigated in univariant Al-Cu-Ag alloys during solidification with planar and cellular morphology. Experiments reveal the dynamic selection of small spacings, below the minimum undercooling spacing and show that distinct morphological features pertain to nearly isotropic or anisotropic Al-Al 2 Cu interfaces.

DISEÑO DE MÓDULOS INTERACTIVOS PARA TRATAR EL TRASTORNO POR DÉFICIT DE ATENCIÓN CON HIPERACTIVIDAD - TDAH

Directory of Open Access Journals (Sweden)

EVELYN GARNICA ESTRADA

2016-07-01

Full Text Available This article describes the solution proposed through physical modules and software for treating attention deficit hyperactivity disorder - ADHD; proposed project in order to provide alternative low-cost therapy in order to enhance skills in children with this condition.

AL ITTIJAHAT AL MUNHARIFAH FI AT TAFSIR LI BADLI ASHAB AL MADZAHIB AL NAHWIYYAH WA BADL MAN YAJHALUNA QAWAID AL LUGHAH AL ARABIYYAH FI NADHAR MUHAMMAD HUSAIN AL DZAHABIY

Directory of Open Access Journals (Sweden)

Misbakhudin Misbakhudin

2017-06-01

Full Text Available One of the most precious achievement in qur’anic studies was the book of Al-Ittijâhât al-Munharifah fî al-Tafsîr: Dawâfi’uha wa Daf’uha written by A great Islamic scholar, Muhammad Husein al-Dzahabî. He was succeeded in discussing several issues of corruptions of the exegesis of the holy Qur’an. This article is aimed to explain and to describe his analysis toward several corrupted linguist interpretations in their originations and such corrupted linguistic interpretations of the holy Qur’an which are ignoring Arabic structures and grammers

La regulación audiovisual en la era de la convergencia digital

Directory of Open Access Journals (Sweden)

Mónica Ariño

2008-09-01

Full Text Available El artículo explora tres cuestiones principales. En primer lugar, a qué tipo de contenido hacen referencia los reguladores de contenido convencionales y cómo proponen regularlo al tratar de intervenir respecto al contenido que se divulga por Internet. En segundo lugar, cuál fue la respuesta de Ofcom al Byron Review en relación con la regulación de contenido nocivo en Internet. Y, por último, la naturaleza cambiante de la regulación en el sector de las comunicaciones en general y, como consecuencia de ello, la necesidad de volver a repensar o volver a definir el papel de las autoridades reguladoras.

Ludopatía y estrategias narratológicas : El caso Barrios en Responso de Juan José Saer

OpenAIRE

Degrande, François

2015-01-01

Al inclinarse sobre Responso (1964), novela de los principios muchas veces considerada menor en la obra de Juan José Saer (1937-2005), el artículo muestra la relevancia del autor cuando describe los contornos psicológicos del jugador patológico Barrios. Se presentan las bases antropológicas del juego (Caillois) antes de tratar la ludopatía desde un enfoque clínico (Valleur y Bucher). Sigue un análisis narratológico que tiende a demostrar que algunos de los síntomas de la adicción al juego se ...

La gestión de riesgo de la banca electrónica en el Ecuador y perspectivas de crecimiento :caso Banco del Pichincha

OpenAIRE

Reinoso Villamil, Gabriela

2007-01-01

Muy relacionado al desarrollo económico ecuatoriano, se halla el desempeño bancario, en especial aquel que tiene que afrontar nuevos retos aún más exigentes en lo que tiene que ver con investigación y aplicación tecnológica para dar respuestas más rápidas y eficientes dentro de un mercado competitivo. Por el hecho mismo de que Ecuador vive en un esquema de dolarización, es tarea de todas las organizaciones y en particular de las instituciones financieras, el tratar de ponerse al día en e...

Factor and Organizational Substitutions to Minimize Costs in the Navy

Science.gov (United States)

2013-12-01

than mere labour for capital substitutions if the objective is one of cost minimization. Static input substitution principle that cheaper inputs...produced? Is the correct mix of inputs being used? While advanced treatments of production theory can be found in microeconomics textbooks (e.g... Microeconomic Theory, 3rd Edition, Prentice Hall Johnson, D.C. et al. (2009), “Managing Change on Complex Programs: VIRGINIA Class Cost Reduction,” Naval

The cost-effectiveness of using chronic kidney disease risk scores to screen for early-stage chronic kidney disease.

Science.gov (United States)

Yarnoff, Benjamin O; Hoerger, Thomas J; Simpson, Siobhan K; Leib, Alyssa; Burrows, Nilka R; Shrestha, Sundar S; Pavkov, Meda E

2017-03-13

Better treatment during early stages of chronic kidney disease (CKD) may slow progression to end-stage renal disease and decrease associated complications and medical costs. Achieving early treatment of CKD is challenging, however, because a large fraction of persons with CKD are unaware of having this disease. Screening for CKD is one important method for increasing awareness. We examined the cost-effectiveness of identifying persons for early-stage CKD screening (i.e., screening for moderate albuminuria) using published CKD risk scores. We used the CKD Health Policy Model, a micro-simulation model, to simulate the cost-effectiveness of using CKD two published risk scores by Bang et al. and Kshirsagar et al. to identify persons in the US for CKD screening with testing for albuminuria. Alternative risk score thresholds were tested (0.20, 0.15, 0.10, 0.05, and 0.02) above which persons were assigned to receive screening at alternative intervals (1-, 2-, and 5-year) for follow-up screening if the first screening was negative. We examined incremental cost-effectiveness ratios (ICERs), incremental lifetime costs divided by incremental lifetime QALYs, relative to the next higher screening threshold to assess cost-effectiveness. Cost-effective scenarios were determined as those with ICERs less than $50,000 per QALY. Among the cost-effective scenarios, the optimal scenario was determined as the one that resulted in the highest lifetime QALYs. ICERs ranged from $8,823 per QALY to $124,626 per QALY for the Bang et al. risk score and $6,342 per QALY to $405,861 per QALY for the Kshirsagar et al. risk score. The Bang et al. risk score with a threshold of 0.02 and 2-year follow-up screening was found to be optimal because it had an ICER less than $50,000 per QALY and resulted in the highest lifetime QALYs. This study indicates that using these CKD risk scores may allow clinicians to cost-effectively identify a broader population for CKD screening with testing for albuminuria

Comentario en el aula del poema «Al ruido del Duero» de Claudio Rodríguez

Directory of Open Access Journals (Sweden)

María Antonia MEZQUITA FERNÁNDEZ

2009-11-01

Full Text Available RESUMEN: En el siguiente artículo se tratará de reflejar la experiencia en un aula de Educación Primaria para acercar a los niños la figura de Claudio Rodríguez y centrarnos en un comentario de su poema «Al ruido del Duero». El colegio elegido es el «Arias Gonzalo», de Zamora. Los niños participaron activamente a la hora de aportar ideas y de comentar el texto. Claudio Rodríguez se sentía fascinado y profesaba un gran amor a su tierra, a sus costumbres y al río Duero. Consideraba que los valores más relevantes del ser humano eran la sencillez, la solidaridad y la fraternidad y deseaba unirse y fundirse, primero, con el entorno natural y, después, con los hombres. En mi opinión, la respuesta de los alumnos fue positiva, ya que captaron la esencia de los versos y demostraron, con su colaboración, que los elementos usados para motivarles habían servido. Lo dejaron patente en las cartas, dibujos y poemas que realizaron posteriormente.ABSTRACT: The following article will try to show a commentary on the poem «Al ruido del Duero» by Claudio Rodríguez, from Zamora. The school which was chosen is called «Arias Gonzalo»; it is in Zamora too. The pupils took part actively and their ideas contributed to comment the text. Claudio Rodríguez was fascinated and professed huge love for the place where he was born, the customs of his province and The Duero River. He believed that the most important human values were simplicity, solidarity and brotherhood. First of all, he wished to be bound to nature. As far as mankind is concerned, he always desired to be joined together. In my opinion, the pupils answered positively and they understood the essence of the verses. They all proved that the elements for motivating them were useful. Then, they showed it clearly by drawing pictures, writing letters and poems.

Cost reduction through combined solutions?; Kostensenkung durch Kombinationsloesungen?

Energy Technology Data Exchange (ETDEWEB)

Bilitewski, B. [Technische Univ. Dresden (Germany). Inst. fuer Abfallwirtschaft und Altlasten

1998-09-01

The implementation of material-specific residue treatment processes requires reconstruction measures both in the case of mechanical-biological and in that of thermal treatment plants. Such measures involves great uncertainties and wide variation in cost prediction. The present paper deals with various factors that influence the costs of residual waste treatment. [Deutsch] Zur Umsetzung der stoffspezifischen Restabfallbehandlung sind Anpassungen sowohl der derzeit betriebenen mechanisch-biologischen als auch der thermischen Anlagen erforderlich, was zu Unsicherheiten und grossen Schwankungsbreiten bei den Kostenprognosen fuehrt. Der Bericht beleuchtet verschiedene Einflussgroessen auf die Kosten der Behandlung des Restabfalls. (orig./SR)

A Behavioral Measure of Costly Helping: Replicating and Extending the Association with Callous Unemotional Traits in Male Adolescents.

Directory of Open Access Journals (Sweden)

Joseph T Sakai

Full Text Available Some conduct-disordered youths have high levels of callous unemotional traits and meet the DSM-5's "with limited prosocial emotions" (LPE specifier. These youths often do aggressive, self-benefitting acts that cost others. We previously developed a task, the AlAn's game, which asks participants to repeatedly decide whether to accept or reject offers in which they will receive money but a planned charity donation will be reduced. In our prior work, more "costly helping" (i.e., rejecting the offered money and protecting the donation was associated with lower callous unemotional traits. Here we extend that prior work in a larger sample of adolescent male patients with serious conduct problems and controls, and test whether this association is mediated specifically by a Moral Elevation response (i.e., a positive emotional response to another's act of virtue.The adolescent male participants were: 45 patients (23 with LPE and 26 controls, who underwent an extensive phenotypic assessment including a measure of Moral Elevation. About 1 week later participants played the AlAn's game.All AlAn's game outcomes demonstrated significant group effects: (1 money taken for self (p = 0.02; (2 money left in the charitable donation (p = 0.03; and, (3 costly helping (p = 0.047. Controls took the least money and did the most costly helping, while patients with LPE took the most money and did the least costly helping. Groups also significantly differed in post-stimulus Moral Elevation scores (p = 0.005. Exploratory analyses supported that the relationship between callous unemotional traits and costly helping on the AlAn's game may be mediated in part by differences in Moral Elevation.The AlAn's game provides a standardized behavioral measure associated with callous unemotional traits. Adolescents with high levels of callous unemotional traits engage in fewer costly helping behaviors, and those differences may be related to blunting of positive emotional responses.

Cost-effectiveness of 3-month paliperidone treatment for chronic schizophrenia in Spain.

Science.gov (United States)

Einarson, Thomas R; Bereza, Basil G; Garcia Llinares, Ignacio; González Martín Moro, Beatriz; Tedouri, Fadi; Van Impe, Kristel

2017-10-01

A 3-month long treatment of paliperidone palmitate (PP3M) has been introduced as an option for treating schizophrenia. Its cost-effectiveness in Spain has not been established. To compare the costs and effects of PP3M compared with once-monthly paliperidone (PP1M) from the payer perspective in Spain. This study used the recently published trial by Savitz et al. as a core model over 1 year. Additional data were derived from the literature. Costs in 2016 Euros were obtained from official lists and utilities from Osborne et al. The authors conducted both cost-utility and cost-effectiveness analyses. For the former, the incremental cost per quality-adjusted life-year (QALY) gained was calculated. For the latter, the outcomes were relapses and hospitalizations avoided. To assure the robustness of the analyses, a series of 1-way and probability sensitivity analyses were conducted. The expected cost was lower with PP3M (4,780€) compared with PP1M (5,244€). PP3M had the fewest relapses (0.080 vs 0.161), hospitalizations (0.034 v.s 0.065), and emergency room visits (0.045 v.s 0.096) and the most QALYs (0.677 v.s 0.625). In both cost-effectiveness and cost-utility analyses, PP3M dominated PP1M. Sensitivity analyses confirmed base case findings. For the primary analysis (cost-utility), PP3M dominated PP1M in 46.9% of 10,000 simulations and was cost-effective at a threshold of 30,000€/QALY gained. PP3M dominated PP1M in all analyses and was, therefore, cost-effective for treating chronic relapsing schizophrenia in Spain. For patients who require long-acting therapy, PP3M appears to be a good alternative anti-psychotic treatment.

Reactive control processes contributing to residual switch cost and mixing cost in young and old adults

Directory of Open Access Journals (Sweden)

Lisa Rebecca Whitson

2014-04-01

Full Text Available In task-switching paradigms, performance is better when repeating the same task than when alternating between tasks (switch cost and when repeating a task alone rather than intermixed with another task (mixing cost. These costs remain even after extensive practice and when task cues enable advanced preparation (residual costs. Moreover, residual RT mixing cost has been consistently shown to increase with age. Residual switch and mixing costs modulate the amplitude of the stimulus-locked P3b. This mixing effect is disproportionately larger in older adults who also prepare more for and respond more cautiously on these ‘mixed’ repeat trials (Karayanidis et al., 2011. In this study, we examine stimulus-locked and response-locked P3 and lateralized readiness potentials to identify whether residual switch and mixing cost arise from the need to control interference at the level of stimulus processing or response processing. Residual mixing cost was associated with control of stimulus-level interference, whereas residual switch cost was also associated with a delay in response selection. In older adults, the disproportionate increase in mixing cost was associated with greater interference at the level of decision-response mapping and response programming for repeat trials in mixed-task blocks. We argue that, together with evidence of greater proactive control and more cautious responding for these trials, these findings suggest that older adults strategically recruit greater proactive and reactive control to overcome increased susceptibility to post-stimulus interference. This interpretation is consistent with recruitment of compensatory strategies to compensate for reduced repetition benefit rather than an overall decline on cognitive flexibility.

Multi-step wrought processing of TiAl-based alloys

International Nuclear Information System (INIS)

Fuchs, G.E.

1997-04-01

Wrought processing will likely be needed for fabrication of a variety of TiAl-based alloy structural components. Laboratory and development work has usually relied on one-step forging to produce test material. Attempts to scale-up TiAl-based alloy processing has indicated that multi-step wrought processing is necessary. The purpose of this study was to examine potential multi-step processing routes, such as two-step isothermal forging and extrusion + isothermal forging. The effects of processing (I/M versus P/M), intermediate recrystallization heat treatments and processing route on the tensile and creep properties of Ti-48Al-2Nb-2Cr alloys were examined. The results of the testing were then compared to samples from the same heats of materials processed by one-step routes. Finally, by evaluating the effect of processing on microstructure and properties, optimized and potentially lower cost processing routes could be identified

Social processes explaining the benefits of Al-Anon participation.

Science.gov (United States)

Timko, Christine; Halvorson, Max; Kong, Calvin; Moos, Rudolf H

2015-12-01

This study examined social processes of support, goal direction, provision of role models, and involvement in rewarding activities to explain benefits of participating in Al-Anon, a 12-step mutual-help program for people concerned about another person's substance use. Newcomers to Al-Anon were studied at baseline and 6 months later, at which time they were identified as having either sustained attendance or dropped out. Among both newcomers and established Al-Anon members ("old-timers"), we also used number of Al-Anon meetings attended during follow-up to indicate extent of participation. Social processes significantly mediated newcomers' sustained attendance status versus dropped out and outcomes of Al-Anon in the areas of life context (e.g., better quality of life, better able to handle problems due to the drinker), improved positive symptoms (e.g., higher self-esteem, more hopeful), and decreased negative symptoms (e.g., less abuse, less depressed). Social processes also significantly mediated newcomers' number of meetings attended and outcomes. However, among old-timers, Al-Anon attendance was not associated with outcomes, so the potential mediating role of social processes could not be examined, but social processes were associated with outcomes. Findings add to the growing body of work identifying mechanisms by which 12-step groups are effective, by showing that bonding, goal direction, and access to peers in recovery and rewarding pursuits help to explain associations between sustained Al-Anon participation among newcomers and improvements on key concerns of Al-Anon attendees. Al-Anon is free of charge and widely available, making it a potentially cost-effective public health resource for help alleviating negative consequences of concern about another's addiction. (c) 2016 APA, all rights reserved).

76 FR 14543 - Federal Acquisition Regulation; Proper Use and Management of Cost-Reimbursement Contracts

Science.gov (United States)

2011-03-16

..., Sequence 1] RIN 9000-AL78 Federal Acquisition Regulation; Proper Use and Management of Cost-Reimbursement... other than firm-fixed-price contracts (e.g., cost-reimbursement, time-and-material, and labor-hour...-reimbursement contracts and identifies the following three areas that the Defense Acquisition Regulation Council...

Synthesis of MgO nanoparticle loaded mesoporous Al2O3 and its defluoridation study

International Nuclear Information System (INIS)

Dayananda, Desagani; Sarva, Venkateswara R.; Prasad, Sivankutty V.; Arunachalam, Jayaraman; Parameswaran, Padmanabhan; Ghosh, Narendra N.

2015-01-01

Highlights: • Simple and cost effective preparation of MgO nanoparticles loaded mesoporous Al 2 O 3 . • Adsorbents possess high surface area and mesoporous structure. • Higher fluoride removal capacity of MgO loaded Al 2 O 3 than that of pure Al 2 O 3 . • Faster fluoride adsorption kinetics of MgO loaded Al 2 O 3 from water. - Abstract: MgO nanoparticle loaded mesoporous alumina has been synthesized using a simple aqueous solution based cost effective method for removal of fluoride from water. Wide angle powder X-ray diffraction, nitrogen adsorption desorption analysis, transmission electron microscopy techniques and energy dispersive X-ray spectroscopy were used to characterize the synthesized adsorbents. Synthesized adsorbents possess high surface area with mesoporous structure. The adsorbents have been thoroughly investigated for the adsorption of F − using batch adsorption method. MgO nanoparticle loading on mesoporous Al 2 O 3 enhances the F − adsorption capacity of Al 2 O 3 from 56% to 90% (initial F − concentration = 10 mg L −1 ). Kinetic study revealed that adsorption kinetics follows the pseudo-second order model, suggesting the chemisorption mechanism. The F − adsorption isotherm data was explained by both Langmuir and Freundlich model. The maximum adsorption capacity of 40MgO@Al 2 O 3 was 37.35 mg g −1 . It was also observed that, when the solutions having F − concentration of 5 mg L −1 and 10 mg L −1 was treated with 40MgO@Al 2 O 3 , the F − concentration in treated water became <1 mg L −1 , which is well below the recommendation of WHO

How Opportunity Costs Decrease the Probability of War in an Incomplete Information Game

OpenAIRE

Polachek, Solomon; Xiang, Jun

2008-01-01

This paper shows that the opportunity costs resulting from economic interdependence decrease the equilibrium probability of war in an incomplete information game. This result is strongly consistent with existing empirical analyses of the inverse trade-conflict relationship, but is the opposite of the conclusion reached by Gartzke et al. (2001), who reject the opportunity cost argument in a game-theoretic framework. As a result of this paper's findings, one cannot dismiss the opportunity cost ...

Hybrid wind-PV grid connected power station case study: Al Tafila, Jordan

Energy Technology Data Exchange (ETDEWEB)

El-Tous, Yousif [Department of Electrical Engineering/Faculty of Engineering Technology/ Al-Balqa' Applied University, Amman, P.O.Box (15008), Marka Ashamalia (Jordan); Al-Battat, Saleh [Department of substation maintenance and protection, National Electric Power Company (NEPCO), Amman (Jordan); Abdel Hafith, Sandro [Department of technical support and project supervision/Integrated power systems co., Amman (Jordan)

2012-07-01

In this paper, we are providing an attempt to highlight the importance of renewable energy, more specifically, the one produced from a wind-solar hybrid system. This purpose will be achieved through providing a detailed case study for such system that would be applied in Al-Tafila, Jordan. First and foremost site assessment has been conducted based on an intensive literature review for the data available regarding the availability of wind and solar energy in Jordan and resulted in the selection of Al-Tafila 2 district as the best option among all. Then, the components of the power station and its size have been selected based on specific criteria that make the station as much efficient and competitive as possible. To obtain the output of the different components with respect to the demand for a period of 25 years, a system model was built using HOMER. Finally, the total capital cost of the system was calculated and resulted to be (63400168) $ and with a cost of energy of (0.053) $/kWh which is a very competitive and feasible cost compared to similar international projects and to the conventional energy price.

A propósito del aborto

OpenAIRE

Casado, María

2008-01-01

Tratar adecuadamente en el actual contexto plural la cuestión del aborto, no es oportuno centrarla en torno a los términos matar y no matar, o justo e injusto, sino más bien en un conflicto de valores y de su jerarquización. En ninguna concepción el aborto es un bien, y el reconocimiento del derecho al aborto no implica nunca la obligación de abortar.

La prensa amarilla y los extraterrestres

Directory of Open Access Journals (Sweden)

Lic. David R. Díaz

2000-01-01

Full Text Available No hay duda de que uno de los temas que más recursos genera a los mecenas del cine y de la prensa amarillista es el de los extraterrestres. Prácticamente todas las revistas de corte sensacionalista recurren a menudo al tema de los extraterrestres para tratar de explicar algún "misterio", sea auténtico o inventado, con el fin de atraer la atención de los clientes.

Entre el erotismo y la pornografía

Directory of Open Access Journals (Sweden)

Edmundo Ribadeneira

2015-01-01

Full Text Available ¿Dónde termina el erotismo y comienza la pornografía? ¿Cuál el lugar de la obscenidad? Son algunas de las inquietudes que el autor aborda al tratar sobre estas tres expresiones de la sexualidad humana, que se ubican entre la indecencia más crasa y la imaginación artística, bastante atravesadas por la obscenidad de la política y el mercantilismo

273. Remodelado de la pared de la aorta torácica después de la reparación de disección de aorta con la trompa de elefante congelada

Directory of Open Access Journals (Sweden)

C.A. Mestres

2012-04-01

Conclusión: La TEC promueve el remodelado aórtico con estabilización de LV, reducción de LF y aumento de relación LV/LF. Hay tendencia, sin llegar a la significación estadística, al año postoperatorio probablemente por el tamaño de la muestra. La TEC podría reducir la necesidad de intervenciones tardías para tratar la FL residual.

Incidence and Economic Cost of Bovine Trypanosomosis in ...

African Journals Online (AJOL)

Incidence and economic cost of cases of bovine trypanosomosis in nomadic herds at the Jos Plateau from 1997 to 2001 were determined. These were done using records kept at the Plateau State Ministry of Animal and Forest Resources headquarters at Jos, and the model described by Alonge et al. (1984). The incidence ...

Turismo Alternativo y Educación. Una propuesta para contribuir al desarrollo humano.

Directory of Open Access Journals (Sweden)

César David Torres Fernández

2013-01-01

Full Text Available Este trabajo realiza una propuesta para contribuir al desarrollo humano, la problemática a tratar es la falta del mismo en este planeta. Por desarrollo humano se entiende la evolución integral del ser humano desde el punto de vista socioeconómico, político, cultural y espiritual (en armonía consigo mismo, con la naturaleza y con los demás seres humanos. En nuestro país existe pobreza, desempleo, corrupción, desigualdad, una pésima educación y cultura, así como problemas de alimentación que lo ubican entre los países con mayor obesidad adulta e infantil en el mundo, existiendo también en las zonas marginadas la desnutrición infantil. Por ello, debemos propiciar diversas opciones de desarrollo; se considera que el turismo alternativo, vinculado a la educación y a la cultura, puede contribuir de manera importante a contrarrestar la problemática antes planteada. En este sentido, nos interesa trabajar con las nuevas generaciones a manera de prevención, concientizándolas, que conozcan y practiquen los valores éticos, morales, familiares, espirituales, etcétera. En el aspecto metodológico, la investigación es de tipo bibliográfico, trabajo de campo, entrevistas y observaciones propias. Es un proyecto que surge como una alternativa dentro del desarrollo sustentable, con actividades de turismo de aventura y ecoturismo, asociado con talleres educativos relacionados con educación ambiental, valores, formación humana y social, educación para la paz, etcétera.

Estudio de los condicionantes que afectan al aprendizaje de las matemáticas empresariales.

Directory of Open Access Journals (Sweden)

Vázquez Cueto, Mª José

2003-01-01

Full Text Available El propósito de este trabajo es tratar de identificar la relevancia de algunas variables, características personales y de formación del alumno, sobre la calificación obtenida por el alumno en la asignatura Matemáticas I (programa de Álgebra Lineal, para la determinación, a priori, de la mayor o menor probabilidad de superar las asignaturas de Matemáticas de primer curso de la Licenciatura de Administración y Dirección de Empresas. Dado que la variable dependiente es discreta, se utilizarán las técnicas de regresión logística.

Comparative analysis of Nb and Ti addition in the Cu-11,8%wt.Al-0,5%wt.Be e Cu-11,8%wt.Al-3,0%wt.Ni shape memory alloy; Analise comparativa da adicao de NB e TI nas ligas Cu-11,8Al-0,5Be e Cu-11,8Al-3,0Ni passiveis do efeito memoria de forma

Energy Technology Data Exchange (ETDEWEB)

Silva Junior, M.Q. da; Oliveira, G.D. de, E-mail: manoel.quirino@ufersa.edu.br [Universidade Federal Rural do Semi-Arido (UFERSA), Mossoro, RN (Brazil)

2014-07-01

The system of the Cu-Al alloys shape memory alloy have been the subject of many studies due to a wide range of possible applications and relatively low cost, and the chemical composition of the main factors that determine the properties of these properties. This work analyzed the influence of Nb and Ti elements in Cu-11,8Al-0,5Be and Cu-11,8Al-3,0Ni alloy. The alloys are obtained by melting and passed through homogenizing heat treatment followed by water quenching at 30°C. The samples were characterized by Microscopy Optical, X-ray Diffraction and Microhardness testing. The alloys showed fine precipitates of second phase homogeneously distributed in the matrix that provides improvement in the properties of these alloys. (author)

Validating the use of Hospital Episode Statistics data and comparison of costing methodologies for economic evaluation: an end-of-life case study from the Cluster randomised triAl of PSA testing for Prostate cancer (CAP).

Science.gov (United States)

Thorn, Joanna C; Turner, Emma L; Hounsome, Luke; Walsh, Eleanor; Down, Liz; Verne, Julia; Donovan, Jenny L; Neal, David E; Hamdy, Freddie C; Martin, Richard M; Noble, Sian M

2016-04-29

To evaluate the accuracy of routine data for costing inpatient resource use in a large clinical trial and to investigate costing methodologies. Final-year inpatient cost profiles were derived using (1) data extracted from medical records mapped to the National Health Service (NHS) reference costs via service codes and (2) Hospital Episode Statistics (HES) data using NHS reference costs. Trust finance departments were consulted to obtain costs for comparison purposes. 7 UK secondary care centres. A subsample of 292 men identified as having died at least a year after being diagnosed with prostate cancer in Cluster randomised triAl of PSA testing for Prostate cancer (CAP), a long-running trial to evaluate the effectiveness and cost-effectiveness of prostate-specific antigen (PSA) testing. Both inpatient cost profiles showed a rise in costs in the months leading up to death, and were broadly similar. The difference in mean inpatient costs was £899, with HES data yielding ∼8% lower costs than medical record data (differences compatible with chance, p=0.3). Events were missing from both data sets. 11 men (3.8%) had events identified in HES that were all missing from medical record review, while 7 men (2.4%) had events identified in medical record review that were all missing from HES. The response from finance departments to requests for cost data was poor: only 3 of 7 departments returned adequate data sets within 6 months. Using HES routine data coupled with NHS reference costs resulted in mean annual inpatient costs that were very similar to those derived via medical record review; therefore, routinely available data can be used as the primary method of costing resource use in large clinical trials. Neither HES nor medical record review represent gold standards of data collection. Requesting cost data from finance departments is impractical for large clinical trials. ISRCTN92187251; Pre-results. Published by the BMJ Publishing Group Limited. For permission to use

Microstructure analysis of the automotive Al-Si-Cu castings

Directory of Open Access Journals (Sweden)

M. Krupiński

2008-04-01

Full Text Available The developed design methodologies both the material and technological ones will make it possible to improve shortly the quality of materials from the light alloys in the technological process, and the automatic process flow correction will make the production cost reduction possible, and - first of all - to reduce the amount of the waste products. In the metal casting industry, an improvement of component quality depends mainly on better control over the production parameters.Castings were analysed in the paper of car engine blocks and heads from the Al-Si-Cu alloys of the AC-AlSi7Cu3Mg type fabricated with the “Cosworth” technological process. In this work the AC-AlSi7Cu3Mg alloy structure was investigated, of this alloy samples were cut of for structure analysis of the cylinder part as well of crankshaft of a fuel engine. The investigation shows a difference in the (phase structure morphology as a result of cast cooling rate.

Exploring the influence of constitutive models and associated parameters for the orthogonal machining of Ti6Al4V

Science.gov (United States)

Pervaiz, S.; Anwar, S.; Kannan, S.; Almarfadi, A.

2018-04-01

Ti6Al4V is known as difficult-to-cut material due to its inherent properties such as high hot hardness, low thermal conductivity and high chemical reactivity. Though, Ti6Al4V is utilized by industrial sectors such as aeronautics, energy generation, petrochemical and bio-medical etc. For the metal cutting community, competent and cost-effective machining of Ti6Al4V is a challenging task. To optimize cost and machining performance for the machining of Ti6Al4V, finite element based cutting simulation can be a very useful tool. The aim of this paper is to develop a finite element machining model for the simulation of Ti6Al4V machining process. The study incorporates material constitutive models namely Power Law (PL) and Johnson – Cook (JC) material models to mimic the mechanical behaviour of Ti6Al4V. The study investigates cutting temperatures, cutting forces, stresses, and plastic strains with respect to different PL and JC material models with associated parameters. In addition, the numerical study also integrates different cutting tool rake angles in the machining simulations. The simulated results will be beneficial to draw conclusions for improving the overall machining performance of Ti6Al4V.

Familial ALS

Science.gov (United States)

Boylan, Kevin

2015-01-01

Synopsis Genes linked to ALS susceptibility are being identified at an increasing rate owing to advances in molecular genetic technology. Genetic mechanisms in ALS pathogenesis appear to exert major effects in ~10% of patients, but genetic factors at some level may be important components of disease risk in most ALS patients. Identification of gene variants associated with ALS has informed concepts of the pathogenesis of ALS, aided the identification of therapeutic targets, facilitated research to develop new ALS biomarkers, and supported the establishment of clinical diagnostic tests for ALS-linked genes. Translation of this knowledge to ALS therapy development is ongoing. PMID:26515623

Malamih al-Ashwat al-'Arabiyyah wa Makharijaha

Directory of Open Access Journals (Sweden)

Amrah Muhammad Kasim

2015-12-01

Full Text Available This writing discusses on al-ashwat al-‘arabiyyah that is known with “phonetic” term. It talks and interprets makharij al-huruf or place for producing sounds and also processing production of sounds by parts of mouth in Arabic language. The problems of sounds and its systems in Arabic language have been conducted by the scholars of al-ashwat al-‘arabiyyah attractively, neatly, and detail and gotten ahead the phonetic western scholars. Part of their analysis results formulate the study about al-ashwat al-sakinah (al-Shamit is known with vocal and consonant sounds in research questions shawait – shawamit. Ibnu Jinni has formulated “harakat”(wowel in Arabic language and dimension of letter  mad and liyn on alif  letter - waw - ya’ (ا و ي, from these letters create  harakat fathah, dammah, and kasrah. Moreover, in this writing also exist the description of hija’i letters and its makhraj that are correct from parts of mouth and the unity of coordinative sounds that produce sounds in morphemes arrangement, in one word that produces meaning. The result of phonological study has divided al-ashwat to be kinds of sound like the pronounced sounds, produced sounds from mouth, and heard sound.

Assessment of health-cost externalities of air pollution at the national level using the EVA model system

Energy Technology Data Exchange (ETDEWEB)

Brandt, J.; Silver, J.D.; Frohn, L.M. (and others)

2011-07-15

Air pollution has significant negative impacts on human health and well-being, which entail substantial economic consequences. We have developed an integrated model system, EVA (External Valuation of Air pollution; Frohn et al., 2005; Andersen et al., 2007; Brandt et al., 2010), to assess health-related economic externalities of air pollution resulting from specific emission sources or sectors. The EVA system was initially developed to assess externalities from power production, but in this study it is extended to evaluate costs at the national level from all major emission sectors. In this study, we estimate the impacts and total externality costs from the main emission sectors in Denmark, representing the 10 major SNAP codes. Furthermore, we assess the impacts and externality costs of all emissions simultaneously from the whole of Europe as well as from international ship traffic in general, since this sector seems to be very important but is currently unregulated. (Author)

Elevated temperature characterization of electron beam freeform fabricated Ti-6Al-4V and dispersion strengthened Ti-8Al-1Er

Energy Technology Data Exchange (ETDEWEB)

Bush, R.W., E-mail: ralph.bush@usafa.edu [Department of Engineering Mechanics, 2354 Fairchild Dr., U.S. Air Force Academy, USAF Academy, CO 80840 (United States); Brice, C.A. [Lockheed Martin Aeronautics Co., Fort Worth, TX (United States)

2012-09-30

Highlights: Black-Right-Pointing-Pointer Electron beam freeform fabrication process. Black-Right-Pointing-Pointer Ti-6Al-4V and rare-earth dispersion Ti alloy. Black-Right-Pointing-Pointer Tensile, creep, and oxidation properties comparable to alloys made with conventional fabrication methods. Black-Right-Pointing-Pointer Fabrication process allows use of rare-earth dispersion Ti alloy. - Abstract: Electron beam freeform fabrication is an additive manufacturing process that can be used to build fully dense, structural metallic parts directly from a three-dimensional computer model. This technique can replace conventional fabrication methods, such as forging or machining from plate, and enable significant cost, time, and tool savings. Additionally, this method enables the fabrication of alloys with novel compositions that are not well suited to production via ingot metallurgy processes. Ti-8Al-1Er is an experimental dispersion strengthened titanium alloy composition that requires rapid cooling to achieve optimal properties and thus is not amenable to ingot metallurgy production methods. Oxide dispersion strengthened alloys, such as Ti-8Al-1Er are known to have excellent thermal stability and improved high temperature properties. In this work, the room temperature tensile, elevated temperature tensile, creep properties and oxidation resistance of electron beam additive manufactured Ti-6Al-4V and Ti-8Al-1Er were measured and compared to those of laser beam additive manufactured Ti-8Al-1Er and wrought Ti-6Al-4V. Elevated temperature tensile properties were measured between 93 Degree-Sign and 538 Degree-Sign C. Creep tests were performed between 425 Degree-Sign and 455 Degree-Sign C at stresses between 345 and 483 MPa. It was found that the elevated temperature properties of the electron beam additive manufactured products are comparable to those of wrought forms. The elevated temperature strengths of Ti-8Al-1Er are comparable to those of Ti-6Al-4V in percentage of room

Costos de atención médica de las enfermedades atribuibles al consumo de tabaco en América: revisión de la literatura Literature review of health care costs of diseases attributable to tobacco consumption in the Americas

Directory of Open Access Journals (Sweden)

Luz Myriam Reynales-Shigematsu

2006-01-01

Full Text Available Con el objetivo de recopilar la información de los estudios de costos de atención médica atribuibles al consumo de tabaco publicados en la literatura científica y de evaluar las diferentes estrategias metodológicas utilizadas en la estimación, se revisaron los trabajos identificados a través de MedLINE y de las referencias bibliográficas de los libros publicados por el Banco Mundial, la Organización Mundial de la Salud, la Organización Panamericana de la Salud, el Grupo de la Investigación Interdisciplinaria de la Salud de Canadá, así como el documento técnico utilizado en el litigio enfrentado por el estado de Minnesota, Estados Unidos de América, contra la industria tabacalera. Se incluyeron todos los estudios publicados en la literatura sobre el tema desde hace más de 25 años. Se obtuvo información de la población de estudio, la perspectiva de costeo, el tipo de análisis para la estimación de los costos de atención médica y la metodología de atribución de costos al consumo de tabaco. Además, se agregó un comentario de los hallazgos relevantes y de las limitaciones de cada uno de los estudios. Los costos anuales de atención médica atribuibles al consumo de tabaco oscilan entre 6 a 14% de los gastos personales en salud. Desde la primera publicación hasta la fecha se observa un progreso en la metodología de la estimación, no sólo desde la perspectiva epidemiológica -que afina la atribución de los costos al factor de riesgo- sino desde la económica -que amplía la estimación de los costos desde una perspectiva social. Se concluye que el consumo de tabaco deriva en altos costos de atención médica, y representa un alto costo social por las muertes prematuras que genera en la sociedad.The objective of this study was to compile information from published scientific literature about health care costs attributable to tobacco consumption and evaluate the different methodological strategies used in calculating

Costs of moderate to severe chronic pain in primary care patients – a study of the ACCORD Program

Directory of Open Access Journals (Sweden)

Lalonde L

2014-07-01

Full Text Available Lyne Lalonde,1–4 Manon Choinière,3,5 Élisabeth Martin,2,3 Djamal Berbiche,2,3 Sylvie Perreault,1,6 David Lussier7–91Faculty of Pharmacy, Université de Montréal, Montreal, QC, Canada; 2Équipe de recherche en soins de première ligne, Centre de santé et de services sociaux de Laval, Laval, QC, Canada; 3Centre de recherche du Centre hospitalier de l'Université de Montréal (CRCHUM, Montreal, QC, Canada; 4Sanofi Aventis Endowment Chair in Ambulatory Pharmaceutical Care, Université de Montréal and Centre de santé et de services sociaux de Laval, QC, Canada; 5Department of Anesthesiology, Faculty of Medicine, Université de Montréal, Montreal, QC, Canada; 6Sanofi Aventis Endowment Research Chair in Optimal Drug Use, Université de Montréal, Montreal, QC, Canada; 7Institut universitaire de gériatrie de Montréal, Montreal, QC, Canada; 8Division of Geriatric Medicine and Alan-Edwards Centre for Research on Pain, McGill University, Montreal, QC, Canada; 9Department of Medicine, Faculty of Medicine, Université de Montréal, Montreal, QC, CanadaBackground: The economic burden of chronic noncancer pain (CNCP remains insufficiently documented in primary care.Purpose: To evaluate the annual direct health care costs and productivity costs associated with moderate to severe CNCP in primary care patients taking into account their pain disability.Materials and methods: Patients reporting noncancer pain for at least 6 months, at a pain intensity of 4 or more on a 0 (no pain to 10 (worst possible pain intensity scale, and at a frequency of at least 2 days a week, were recruited from community pharmacies. Patients' characteristics, health care utilization, and productivity losses (absenteeism and presenteeism were documented using administrative databases, pharmacies' renewal charts, telephone, and self-administered questionnaires. Patients were stratified by tertile of pain disability measured by the Brief Pain Inventory questionnaire

Transient oxidation of Al-deposited Fe-Cr-Al alloy foil

International Nuclear Information System (INIS)

Andoh, A.

1997-01-01

The oxide phases formed on an Al-deposited Fe-Cr-Al alloy foil and an Fe-Cr-Al alloy foil of the same levels of Al and (La+Ce) contents, and their oxidation kinetics have been studied in air at 1173 and 1373 K using TGA, XRD and SEM. Al deposition promotes the growth of metastable aluminas (θ-Al 2 O 3 , γ-Al 2 O 3 ). Scales consisting of θ-Al 2 O 3 and a small amount of α-Al 2 O 3 develop on the Al-deposited foil at 1173 K and exhibit the whisker-type morphology. In the early stage of oxidation at 1373 K, thick scales consisting of θ-Al 2 O 3 and α-Al 2 O 3 grow rapidly on the Al-deposited foil. The transformation from θ-Al 2 O 3 to α-Al 2 O 3 is very fast, and the scales result in only α-Al 2 O 3 . In contrast, α-Al 2 O 3 scales containing a minor amount of FeAl 2 O 4 develop on the alloy foil. The growth rate of α-Al 2 O 3 scales on the Al-deposited foil is smaller than that on the alloy foil and very close to that on NiAl at 1373 K. (orig.)

Cost-effectiveness of dihydroartemisinin-piperaquine compared with artemether-lumefantrine for treating uncomplicated malaria in children at a district hospital in Tanzania.

Science.gov (United States)

Mori, Amani T; Ngalesoni, Frida; Norheim, Ole F; Robberstad, Bjarne

2014-09-15

Dihydroartemisinin-piperaquine (DhP) is highly recommended for the treatment of uncomplicated malaria. This study aims to compare the costs, health benefits and cost-effectiveness of DhP and artemether-lumefantrine (AL) alongside "do-nothing" as a baseline comparator in order to consider the appropriateness of DhP as a first-line anti-malarial drug for children in Tanzania. A cost-effectiveness analysis was performed using a Markov decision model, from a provider's perspective. The study used cost data from Tanzania and secondary effectiveness data from a review of articles from sub-Saharan Africa. Probabilistic sensitivity analysis was used to incorporate uncertainties in the model parameters. In addition, sensitivity analyses were used to test plausible variations of key parameters and the key assumptions were tested in scenario analyses. The model predicts that DhP is more cost-effective than AL, with an incremental cost-effectiveness ratio (ICER) of US$ 12.40 per DALY averted. This result relies on the assumption that compliance to treatment with DhP is higher than that with AL due to its relatively simple once-a-day dosage regimen. When compliance was assumed to be identical for the two drugs, AL was more cost-effective than DhP with an ICER of US$ 12.54 per DALY averted. DhP is, however, slightly more likely to be cost-effective compared to a willingness-to-pay threshold of US$ 150 per DALY averted. Dihydroartemisinin-piperaquine is a very cost-effective anti-malarial drug. The findings support its use as an alternative first-line drug for treatment of uncomplicated malaria in children in Tanzania and other sub-Saharan African countries with similar healthcare infrastructures and epidemiology of malaria.

Low Cost, Low Power, High Sensitivity Magnetometer

Science.gov (United States)

2008-12-01

which are used to measure the small magnetic signals from brain. Other types of vector magnetometers are fluxgate , coil based, and magnetoresistance...concentrator with the magnetometer currently used in Army multimodal sensor systems, the Brown fluxgate . One sees the MEMS fluxgate magnetometer is...Guedes, A.; et al., 2008: Hybrid - LOW COST, LOW POWER, HIGH SENSITIVITY MAGNETOMETER A.S. Edelstein*, James E. Burnette, Greg A. Fischer, M.G

Proton irradiation studies on Al and Al5083 alloy

Science.gov (United States)

Bhattacharyya, P.; Gayathri, N.; Bhattacharya, M.; Gupta, A. Dutta; Sarkar, Apu; Dhar, S.; Mitra, M. K.; Mukherjee, P.

2017-10-01

The change in the microstructural parameters and microhardness values in 6.5 MeV proton irradiated pure Al and Al5083 alloy samples have been evaluated using different model based techniques of X-ray diffraction Line Profile Analysis (XRD) and microindendation techniques. The detailed line profile analysis of the XRD data showed that the domain size increases and saturates with irradiation dose both in the case of Al and Al5083 alloy. The corresponding microstrain values did not show any change with irradiation dose in the case of the pure Al but showed an increase at higher irradiation doses in the case of Al5083 alloy. The microindendation results showed that unirradiated Al5083 alloy has higher hardness value compared to that of unirradiated pure Al. The hardness increased marginally with irradiation dose in the case of Al5083, whereas for pure Al, there was no significant change with dose.

Control físico – etológico de moscas domésticas, usando tres tipos de atrayentes en tres prototipos de trampas

OpenAIRE

Villavicencio Machado, César Rafael

2017-01-01

En la ganadería tanto de carne, leche o doble propósito, las moscas son un serio problema, ya que pueden ser causa de la disminución en la producción por estrés y desgaste de energía por parte del animal al tratar de espantarlas, también por ser un insecto vector de una variedad de parásitos, algunos de ellos de mucha importancia en la salud animal y humana, pero también son importantes por provocar contaminaciones en la leche al elevar la presencia de células somáticas que merman la calidad,...

PEMBARUAN MASLAḤAH DALAM MAQĀṢID AL- SHARĪ‘AH: TELAAH HUMANISTIS TENTANG AL-KULLIYYĀT AL-KHAMSAH

Directory of Open Access Journals (Sweden)

Zaenuddin Mansyur

2012-06-01

Full Text Available Abstract:   In order to answer a variety of issues faced by human being in the current era, such as human rights abuses, social disintegration, and terrorism, the renewal of Islamic law in the level of theoretical and practical aspects is very urgent. This paper aims to examine one of the Islamic legal reform efforts, namely to build a more technical understanding of the concept of maṣlaḥah contained in the maqāṣīd sharī‘ah, called the al-kulliyat al-khamsah. Therefore, the concept of maṣlaḥah in ḥifẓ al-dīn is technically defined as al-ḥurriyah al-i‘tiqād (freedom of religion and schools; in ḥifẓ al-nafs as al-karamat al-insān (human being breeding; in ḥifẓ al-nasl as ḥifẓ al-usrah (wholeness and harmony of the family; in ḥifẓ al-māl as al-taḍammun al-insān (social solidarity , and in ḥifẓ al-‘aql as al-ḥuqūq as al-tarbiyāt (increasing human resources quality.Abstrak: Demi menjawab aneka persoalan zaman yang dihadapi manusia era sekarang, seperti penyelewengan terhadap HAM, disintegrasi sosial, dan terorisme, maka pembaharuan hukum Islam dalam tataran teoretis dan praktis urgen dilakukan. Tulisan ini bertujuan untuk mengkaji salah satu upaya pembaruan hukum Islam, yaitu membangun pemahaman yang lebih teknis terhadap konsep maṣlaḥah yang terkandung dalam maqāṣīd sharī‘ah, yang disebut dengan al-kulliyāt al-khamsah. Oleh karena itu, konsep maṣlaḥah dalam ḥifẓu al-dīn secara teknis dimaknai sebagai ḥurriyah al-i‘tiqād (kebebasan untuk beragama dan beraliran; dalam ḥifẓu al-nafs sebagai al-karāmāt al-insān (pemuliaan kemanusiaan; dalam ḥifẓu al-nasl sebagai ḥifẓu al-usrah (keutuhan dan keharmonisan keluarga; dalam ḥifẓu al-māl sebagai al-taḍammun al-insān (solidaritas sosial; dan dalam ḥifẓu al-‘aql sebagai al-ḥuqūq al-tarbiyāt (peningkatan sumber daya manusia.

Quality analysis of the Al-Si-Cu alloy castings

Directory of Open Access Journals (Sweden)

L.A. Dobrzański

2007-04-01

Full Text Available The developed design methodologies both the material and technological ones will make it possible to improve shortly the quality of materials from the light alloys in the technological process, and the automatic process flow correction will make the production cost reduction possible, and - first of all - to reduce the amount of the waste products. Method was developed for analysis of the casting defects images obtained with the X-ray detector analysis of the elements made from the Al-Si-Cu alloys of the AC-AlSi7Cu3Mg type as well as the method for classification of casting defects using the artificial intelligence tools, including the neural networks; the developed method was implemented as software programs for quality control. Castings were analysed in the paper of car engine blocks and heads from the Al-Si-Cu alloys of the AC-AlSi7Cu3Mg type fabricated with the “Cosworth” technological process. The computer system, in which the artificial neural networks as well as the automatic image analysis methods were used makes automatic classification possible of defects occurring in castings from the Al-Si-Cu alloys, assisting and automating in this way the decisions about rejection of castings which do not meet the defined quality requirements, and therefore ensuring simultaneously the repeatability and objectivity of assessment of the metallurgical quality of these alloys.

Combustion synthesis of AlB2-Al2O3 composite powders with AlB2 nanowire structures

Science.gov (United States)

Yang, Pan; Xiao, Guoqing; Ding, Donghai; Ren, Yun; Yang, Shoulei; Lv, Lihua; Hou, Xing

2018-05-01

Using of Al and B2O3 powders as starting materials, and Mg-Al alloy as additives, AlB2-Al2O3 composite powders with AlB2 nanowire structures were successfully fabricated via combustion synthesis method in Ar atmosphere at a pressure of 1.5 MPa. The effect of different amount of Mg-Al alloy on the phase compositions and morphology of the combustion products was investigated. The results revealed that AlB2 and Al2O3 increased, whereas Al decreased with the content of Mg-Al alloy increasing. The impurities MgAl2O4 and AlB12 would exist in the sample with adding of 18 wt% Mg-Al alloy. Interestingly, FESEM/TEM/EDS results showed that AlB2 nanowires were observed in the products when the content of Mg-Al alloy is 6 wt% and 12 wt%. The more AlB2 nanowires can be found as the content of Mg-Al alloy increased. And the yield of AlB2 nanowires with the diameter of about 200 nanometers (nm) and the length up to several tens of micrometers (μm) in the combustion product is highest when the content of Mg-Al alloy is 12 wt%. The vapor, such as Mg-Al (g), B2O2 (g), AlO (g) and Al2O (g), produced during the process of combustion synthesis, reacted with each other to yield AlB2 nanowires by vapor-solid (VS) mechanism and the corresponding model was also proposed.

The effects of boron in TiAl/Ti3Al

International Nuclear Information System (INIS)

Feng, C.R.; Michel, D.J.; Crowe, C.R.

1989-01-01

The authors discuss the TiAl/Ti 3 Al interfacial misfit dislocations structures investigated by TEM in Ti-45Al alloy and Ti-45Al/TiB 2 composite. For TiAl with c/a = 1.02, only a single set of misfit dislocation arrays are crystallographically possible; these were observed in Ti-45Al alloy. However, the observation of three sets of misfit dislocation arrays in the Ti-45Al/TiB 2 composite suggests that the occupation of octahedral sites in the TiAl structure by excess boron was responsible for a decrease in the c/a ratio leading to an increased fcc character of the TiAl at the TiAl/Ti 3 Al interface

Microstructure and mechanical properties of TiAl castings produced by zirconia ceramic mould

Directory of Open Access Journals (Sweden)

Tian Jing

2011-11-01

Full Text Available Owing to their low density and attractive high-temperature properties, gamma titanium aluminide alloys (TiAl alloys, hereafter have significant potential application in the aerospace and automobile industries, in which these materials may replace the heavier nickel-based superalloys at service temperatures of 600 – 900℃. Investment casting of TiAl alloys has become the most promising cost-effective technique for the manufacturing of TiAl components. Ceramic moulds are fundamental to fabricating the TiAl casting components. In the present work, ceramic mould with a zirconia primary coat was designed and fabricated successfully. Investment casting of TiAl blades and tensile test of specimens was carried out to verify the correctness and feasibility of the proposed method. The tensile test results indicate that, at room temperature, the tensile strength and the elongation are about 450 MPa and 0.8%, respectively. At 700℃, the tensile strength decreases to about 410 MPa and the elongation increases to 2.7%. Microstructure and mechanical properties of investment cast TiAl alloy are discussed.

Cost-Effectiveness Analysis in Comparing Alginate Silver Dressing with Silver Zinc Sulfadiazine Cream in the Treatment of Pressure Ulcers

Directory of Open Access Journals (Sweden)

Apirag Chuangsuwanich

2013-09-01

Full Text Available BackgroundThe treatment of pressure ulcers is complicated, given the various wound dressing products available. The cost of different treatments varies and the cost-effectiveness of each product has not been thoroughly evaluated. We compare two wound dressing protocols-alginate silver dressing (AlSD and silver zinc sulfadiazine cream (AgZnSD with regard to wound healing and cost-effectiveness.MethodsPatients with grade III or IV sacral or trochanteric pressure ulcers were eligible for this prospective, randomized controlled trial. The patients were randomized to receive one of the two dressings for an eight-week period. The criteria of efficacy were based on the Pressure Ulcer Scale for Healing (PUSH scoring tool. The cost of treatment was also assessed.ResultsTwenty patients (12 women and 8 men were randomly assigned to receive either AlSD (n=10 or AgZnSD cream (n=10. The demographic data and wound characteristics were comparable in the two groups. The two groups showed no significant difference in the reduction of PUSH score, wound size, or volume of exudate. The tissue type score was significantly lower in the AlSD group (3.15±0.68-1.85±0.68 vs. 2.73±0.79-2.2±0.41; P=0.015. The cost of treatment was significantly lower in the AlSD group (377.17 vs. 467.74 USD, respectively; P<0.0001.ConclusionsAlginate silver dressing could be effectively used in the treatment of grade III and IV pressure ulcers. It can improve wound tissue characteristics and is cost-effective.

DIFICULTADES EN LA IMPLEMENTACION DEL PLAN BEPS EN COLOMBIA

OpenAIRE

Rodríguez-Díaz, Nidia Rocio

2015-01-01

El presente trabajo tiene como finalidad analizar las principales dificultades que debe contraponer Colombia en la implementación del Plan BEPS, cuyo objetivo principal es evitar la erosión de las bases imponibles, lo cual requiere efectuar diversos cambios principalmente en la normatividad referente a aspectos contables y tributarios. Precisamente es esta situación la que genera mayores dificultades, por cuanto entre los Estados se genera competencia al tratar de atraer nuevos inversionistas...

In Situ Fabrication of AlN Coating by Reactive Plasma Spraying of Al/AlN Powder

Directory of Open Access Journals (Sweden)

Mohammed Shahien

2011-10-01

Full Text Available Reactive plasma spraying is a promising technology for the in situ formation of aluminum nitride (AlN coatings. Recently, it became possible to fabricate cubic-AlN-(c-AlN based coatings through reactive plasma spraying of Al powder in an ambient atmosphere. However, it was difficult to fabricate a coating with high AlN content and suitable thickness due to the coalescence of the Al particles. In this study, the influence of using AlN additive (h-AlN to increase the AlN content of the coating and improve the reaction process was investigated. The simple mixing of Al and AlN powders was not suitable for fabricating AlN coatings through reactive plasma spraying. However, it was possible to prepare a homogenously mixed, agglomerated and dispersed Al/AlN mixture (which enabled in-flight interaction between the powder and the surrounding plasma by wet-mixing in a planetary mill. Increasing the AlN content in the mixture prevented coalescence and increased the nitride content gradually. Using 30 to 40 wt% AlN was sufficient to fabricate a thick (more than 200 µm AlN coating with high hardness (approximately 1000 Hv. The AlN additive prevented the coalescence of Al metal and enhanced post-deposition nitriding through N₂ plasma irradiation by allowing the nitriding species in the plasma to impinge on a larger Al surface area. Using AlN as a feedstock additive was found to be a suitable method for fabricating AlN coatings by reactive plasma spraying. Moreover, the fabricated coatings consist of hexagonal (h-AlN, c-AlN (rock-salt and zinc-blend phases and certain oxides: aluminum oxynitride (Al₅O₆N, cubic sphalerite Al₂₃O₂₇N₅ (ALON and Al₂O₃. The zinc-blend c-AlN and ALON phases were attributed to the transformation of the h-AlN feedstock during the reactive plasma spraying. Thus, the zinc-blend c-Al

Two- and three-index formulations of the minimum cost multicommodity k-splittable flow problem

DEFF Research Database (Denmark)

Gamst, Mette; Jensen, Peter Neergaard; Pisinger, David

2010-01-01

The multicommodity flow problem (MCFP) considers the efficient routing of commodities from their origins to their destinations subject to capacity restrictions and edge costs. Baier et al. [G. Baier, E. Köhler, M. Skutella, On the k-splittable flow problem, in: 10th Annual European Symposium...... of commodities has to be satisfied at the lowest possible cost. The problem has applications in transportation problems where a number of commodities must be routed, using a limited number of distinct transportation units for each commodity. Based on a three-index formulation by Truffot et al. [J. Truffot, C...... on Algorithms, 2002, 101–113] introduced the maximum flow multicommodity k-splittable flow problem (MCkFP) where each commodity may use at most k paths between its origin and its destination. This paper studies the -hard minimum cost multicommodity k-splittable flow problem (MCMCkFP) in which a given flow...

COSTES SANITARIOS DIRECTOS DE LAS NEOPLASIAS DE PULMÓN Y VEJIGA DE ORIGEN LABORAL EN ESPAÑA EN 2008

Directory of Open Access Journals (Sweden)

Montserrat García Gómez

2012-01-01

Full Text Available Fundamentos: La falta de reconocimiento del origen laboral de algunos tumores malignos conlleva que el coste de su asistencia sanitaria recaiga sobre el Sistema Nacional de Salud. El objetivo de nuestro estudio es conocer el número de procesos atendidos por cáncer de pulmón y vejiga atribuibles al trabajo en España en el Sistema Nacional de Salud (SNS en 2008, así como los costes sanitarios derivados de su atención. Métodos: El número de procesos se estimó aplicando las fracciones atribuibles al trabajo obtenidas en la literatura. Para el cálculo de los costes se utilizaron datos primarios relativos a la atención especializada del SNS (ambulatoria e ingresos hospitalarios, y fuentes secundarias para calcular el coste de la atención primaria de salud y la atención farmaceútica. Los cálculos se realizaron por enfermedad y sexo. Resultados: 10.652 altas hospitalarias durante 2008 fueron debidas a cánceres de pulmón y vejiga atribuibles al trabajo (se reconocieron 16 como profesionales el mismo año. El tratamiento de estos casos costó casi 88 millones de euros, de los cuales 61,2 corresponden al cáncer de pulmón y 26,5 al de vejiga. Destaca el enorme peso relativo de la atención especializada (64% y el escaso peso de la atención primaria (2,3%. Conclusiones: La magnitud del cáncer de pulmón y vejiga derivado del trabajo en España es muy superior a la que refleja el registro de enfermedades profesionales, siendo imprescindible su reconocimiento como profesional para activar su adecuada prevención. La atención sanitaria de estas enfermedades supone un elevado gasto para el sistema público de salud.

Instability of TiC and TiAl3 compounds in Al-10Mg and Al-5Cu alloys by addition of Al-Ti-C master alloy

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The performance of Al-Ti-C master alloy in refining Al-10Mg and A1-5Cu alloys was studied by using electron probe micro-analyzer (EPMA) and X-ray diffractometer (XRD) analysis.The results indicate that there are obvious fading phenomena in both Al-10Mg and Al-5Cu alloys with the addition of Al-5Ti-0.4C refiner which contains TiC and TiAl3 compounds.Mg element has no influence on the stability of TiC and TiAl3, while TiC particles in Al-10Mg alloy react with Al to form Al4C3 particles, resulting in the refinement fading.However, TiC particles are relatively stable in Al-5Cu alloy, while TiAl3 phase reacts with Al2Cu to produce a new phase Ti(Al, Cu)2, which is responsible for the refinement fading in Al-5Cu alloy.These indicate that the refinement fading will not occur only when both the TiC particles and TiAl3 compound of Al-Ti-C refiner are stable in Al alloys.

Morbilidad, mortalidad y costes sanitarios evitables mediante una estrategia de tratamiento del tabaquismo en España The effects of implementing a smoking cessation intervention in Spain on morbidity, mortality and health care costs

Directory of Open Access Journals (Sweden)

J. González-Enríquez

2002-08-01

Full Text Available Objetivo: Se valoran los efectos que tendría una intervención destinada a reducir el uso de tabaco en la población española de fumadores sobre la morbilidad, la mortalidad y los costes asociados al consumo de tabaco. Método: Se ha adaptado el modelo Health and Economic Consequences of Smoking patrocinado por la OMS y desarrollado por The Lewin Group. La intervención propuesta incluye el acceso a asistencia farmacológica de un 35% de los fumadores que intentan dejar de fumar, y obtienen una tasa global de cesación al año del 7,2%. Las enfermedades estudiadas son: cáncer de pulmón, enfermedad coronaria, enfermedad cerebrovascular, EPOC, asma y bajo peso al nacer. Se estiman los casos de enfermedad y muerte atribuibles al consumo de tabaco evitados y la reducción en el coste sanitario debidos a la intervención, proyectados a 20 años. Resultados: Sin intervención, en el año 1 del modelo 2.136.094 fumadores padecen alguna de las condiciones clínicas atribuibles al consumo de tabaco, el coste asistencial es de 4.286 millones de euros y las muertes atribuibles son 26.537. La intervención propuesta evita 2.613, 9.192, 17.415 y 23.837 casos de enfermedad atribuible al consumo de tabaco en los años 2, 5, 10 y 20 del modelo, respectivamente. Los costes asistenciales acumulados evitados son 3,5 millones de euros en el año 2 y 386 millones de euros a los 20 años. Las muertes acumuladas evitadas son 284 en el año 2 y 9.205 a los 20 años de la intervención. La intervención añade un total de 78.173 años de vida al final del período considerado. Conclusiones: La disponibilidad de nuevas intervenciones eficaces en el tratamiento del tabaquismo y el incremento de la accesibilidad a las mismas pueden contribuir de forma relevante a la reducción de la morbilidad, la mortalidad y los costes sanitarios asociados al tabaquismo en España.Objective: We estimated the effect that a smoking cessation intervention in the Spanish population of

PEMAHAMAN HADITS TARBAWI BURHAN AL ISLAM AL ZARNUJI DALAM KITAB TA’LIM AL MUTA’ALLIM

Directory of Open Access Journals (Sweden)

Benny Afwadzi

2017-01-01

Full Text Available This paper explores the understanding of tarbawi (education hadith from one of the major influential clerics in the Islamic educational system, especially in pesantren. He is Burhan al Islam al Zarnuji with his landmark book Ta’lim al Muta’allim. The conclusion that can be drawn is that al Zarnuji has shades of sufistical view in understanding tarbawi hadith. This can be seen in his understanding of hadith on obligation to seek knowledge (thalab al ilmi faridhatun ‘ala kulli muslimin wa muslimatin, which is interpreted as ilm al hal, the science concerning the condition of the human religious or simplistically said as the religious sciences; and the hadith of intention of studying (innama al a’malu bi al niyyat with the intention for the sake of the hereafter and religion, not mundane. Such an understanding is not something taken for granted, but it can be reinterpreted and perfected in accordance with the spirit of the times of context.

Calculation of Gibbs energy of Zr-Al-Ni, Zr-Al-Cu, Al-Ni-Cu and Zr-Al-Ni-Cu liquid alloys based on quasiregular solution model

International Nuclear Information System (INIS)

Li, H.Q.; Yang, Y.S.; Tong, W.H.; Wang, Z.Y.

2007-01-01

With the effects of electronic structure and atomic size being introduced, the mixing enthalpy as well as the Gibbs energy of the ternary Zr-Al-Cu, Ni-Al-Cu, Zr-Ni-Al and quaternary Zr-Al-Ni-Cu systems are calculated based on quasiregular solution model. The computed results agree well with the experimental data. The sequence of Gibbs energies of different systems is: G Zr-Al-Ni-Cu Zr-Al-Ni Zr-Al-Cu Cu-Al-Ni . To Zr-Al-Cu, Ni-Al-Cu and Zr-Ni-Al, the lowest Gibbs energy locates in the composition range of X Zr 0.39-0.61, X Al = 0.38-0.61; X Ni = 0.39-0.61, X Al = 0.38-0.60 and X Zr = 0.32-0.67, X Al = 0.32-0.66, respectively. And to the Zr-Ni-Al-Cu system with 66.67% Zr, the lowest Gibbs energy is obtained in the region of X Al = 0.63-0.80, X Ni = 0.14-0.24

Bipolar characteristics of AlGaN/AlN/GaN/AlGaN double heterojunction structure with AlGaN as buffer layer

International Nuclear Information System (INIS)

Peng, Enchao; Wang, Xiaoliang; Xiao, Hongling; Wang, Cuimei; Yin, Haibo; Chen, Hong; Feng, Chun; Jiang, Lijuan; Hou, Xun; Wang, Zhanguo

2013-01-01

Highlights: •2DEG and 2DHG coexist in the AlGaN/AlN/GaN/AlGaN DH-structure. •The sheet densities of 2DEG and 2DHG vary with buffer Al content and GaN thickness. •The conditions for the disappearance of 2DHG are discussed. •Increasing buffer Al content provides better electron confinement. •Dislocation scattering is reduced in the DH-structure. -- Abstract: This is a theoretical study of AlGaN/AlN/GaN/AlGaN double heterojunction (DH) structure with AlGaN as buffer layer. Our calculation shows that as the buffer Al content increases, though two-dimensional electron gas (2DEG) sheet density decreases, the channel back-barrier caused by polarization-induced electric field in GaN provides better electron confinement. And under certain conditions the DH-structure shows bipolar characteristics, with an additional two-dimensional hole gas (2DHG) formed at GaN/AlGaN interface. The influence of the buffer Al content and GaN channel thickness on the 2DEG and 2DHG sheet densities are investigated, and the conditions for the disappearance of 2DHG are discussed. Also, the mobility inhibited by dislocation scattering is enhanced in DH-structure due to the enhancement of screening effect of the 2DEG

Cost benefit of caustic recycle for tank waste remediation at the Hanford and Savannah River Sites

International Nuclear Information System (INIS)

DeMuth, S.

1998-01-01

The potential cost savings due to the use of caustic recycle used in conjunction with remediation of radioactive underground storage tank waste, is shown in a figure for the Hanford and Savannah River sites. Two cost savings estimates for each case have been made for Hanford, and one cost savings estimate for each case have been made for Hanford, and one cost savings estimate for each case has been made for the Savannah River site. This is due to the Hanford site remediation effort being less mature than that of Savannah River; and consequently, a range of cost savings being more appropriate for Hanford. This range of cost savings (rather than a ingle value) for each case at Hanford is due to cost uncertainties related to the LAW immobilization operation. Caustic recycle Case-1 has been defined as the sodium required to meet al identified caustic needs for the entire Site. Case-2 has been defined as the maximum sodium which can be separated from the low activity waste without precipitation of Al(OH) 3 . It has been determined that the potential cost savings at Hanford ranges from $194 M to $215 M for Case-1, and $293 M to $324 M for Case-2. The potential cost savings at Savannah River are $186 M for Case-1 and $281 M for Case-2. A discussion of the uncertainty associated with these cost savings estimates can be found in the Discussion and Conclusions section

The effect of aluminum content on phase constitution and heat treatment behavior of Ti-Cr-Al alloys for healthcare application

International Nuclear Information System (INIS)

Sugano, Daisuke; Ikeda, Masahiko

2005-01-01

As life expectancy steadily increases, developing reliable functional materials for healthcare applications gains importance. Titanium and its alloys, while attractive for such applications, are expensive. The present investigation suggests that it may be possible to reduce costs by using new, low-cost beta Ti alloys. To assess their reliability, the heat treatment behavior of beta Ti alloys, Ti-7 mass% Cr with varying Al content (0%, 1.5%, 3.0% and 4.5%), was investigated through electrical resistivity and Vickers hardness measurements. In the Ti-7Cr-0Al alloy quenched from 1173 K, only the beta phase was identified by X-ray diffraction (XRD). In Ti-7Cr-1.5 to 4.5 Al alloys, XRD detected both beta and orthorhombic martensite. On isochronal heat treatment behavior of Ti-7Cr-3.0, 4.5 Al alloys, resistivity at liquid nitrogen temperature and resistivity ratio increased between 423 and 523 K.These increases are due to reverse transformation of orthorhombic martensite to the metastable beta phase

The code of light: al-ghazali and al-suhrawardi

OpenAIRE

Gediminaitė, Barbora

2017-01-01

The Code of Light: Al-Ghazali and Al-Suhrawardi The Bachelor’s thesis The Code of Light in Islam: al-Ghazali and al-Suhrawardi presents a comparative study of light. The study analyses the philosophical systems of al-Ghazali and al-Suhrawardi through the reconstruction of the image of light and its operation principles. The main subject of the thesis are the attributes of light. The main problem of the research is the semantics and contextuality of light in Islamic theology and philosophy. Th...

A novel bio-electrochemical system with sand/activated carbon separator, Al anode and bio-anode integrated micro-electrolysis/electro-flocculation cost effectively treated high load wastewater with energy recovery.

Science.gov (United States)

Gao, Changfei; Liu, Lifen; Yang, Fenglin

2018-02-01

A novel bio-electrochemical system (BES) was developed by integrating micro-electrolysis/electro-flocculation from attaching a sacrificing Al anode to the bio-anode, it effectively treated high load wastewater with energy recovery (maximum power density of 365.1 mW/m 3 and a maximum cell voltage of 0.97 V), and achieving high removals of COD (>99.4%), NH 4 + -N (>98.7%) and TP (>98.6%). The anode chamber contains microbes, activated carbon (AC)/graphite granules and Al anode. It was separated from the cathode chamber containing bifunctional catalytic and filtration membrane cathode (loaded with Fe/Mn/C/F/O catalyst) by a multi-medium chamber (MMC) filled with manganese sand and activated carbon granules, which replaced expensive PEM and reduced cost. An air contact oxidation bed for aeration was still adopted before liquid entering the cathode chamber. micro-electrolysis/electro-flocculation helps in achieving high removal efficiencies and contributes to membrane fouling migration. The increase of activated carbon in the separator MMC increased power generation and reduced system electric resistance. Copyright © 2017 Elsevier Ltd. All rights reserved.

Construcción en cooperación al desarrollo. Hassan Fathy. El futuro a través del pasado

OpenAIRE

Sánchez Miguel, David

2017-01-01

El objetivo de este trabajo es la descripción de la vida y el trabajo de Hassan Fathy, reconocido arquitecto egipcio del siglo XX. Su obra tan característica necesita un reconocimiento como el que se va a realizar en este trabajo. Para hablar correctamente de la obra de Fathy se tratará primero el contexto en el que se movía el arquitecto egipcio, junto con sus ideas principales que le llevaron a destacar en la época. Posteriormente, se analizan 3 tipos de obras según el tipo de arquitect...

Pemikiran Filosofis Sadra Dalam Tafsir Al-Qur’an Al-Karim : Surah Al-’A‘la

Directory of Open Access Journals (Sweden)

Kerwanto Kerwanto

2014-12-01

Full Text Available Abstrak : Dalam tafsir atas Surah al-’A‘lā, Mulla Sadra, melalui karyanya Tafsīr al Qur’ān al-Karīm, mengajak jiwa kita berpetualang menuju lapisan makna terdalam untuk mengenali realitas ketauhidan (al- mabdā’, kenabian (shirāth atau nubuwwah dan kebangkitan (ma‘ād dan mengulasnya secara filosofis. Penelitian ini merupakan suatu upaya untuk menggali manfaat dari aspek-aspek penting dari sumber-sumber keagamaan yang tergali dari petunjuk al Qur’an yang berpadu dengan prinsip- prinsip rasional filosofis dan pengalaman mistik (intuitif Sadra. Setiap bab pada tafsir ini diberikan judul dengan tasbīḥ (pernyataan pemujian dan pensucian, dengan tetap memaparkan beragam pokok persoalan terkait metafisika al-Qur’an. Prinsip-prinsip filosofis yang digunakan dalam risalah tafsir ini bisa menjadi salah satu bukti ketidakberjarakan antara filsafat dengan teks-teks keagamaan. Sadra menggunakan metode tafsir yang tetap menerima sisi lahiriah al-Qur’an, dan selanjutnya mencari misteri-misteri, rahasia-rahasia, dan dengan bantuan intelek (akal, intuisi dan iluminasi Tuhan untuk memperoleh realitas-realitas dan makna- makna dibalik selaput ekternalnya (aspek literalnyaKata kunci : Ḥikmah Muta’āliyah, irfan, al-mabdā’, kebangkitan setelah mati, nubuwwah, takwīl, gerak substansial (ḥarakah jawhariyyah, denotasi utama (al-maqshūd al-ashlī, penyempurnaan diri (takammul, tasbīḥ.  Abstract : In his commentary on Surah al-’ A‘lā, Mulla Sadra, through his Tafsīr al-Qur’ān al-Karīm invites our souls to ventureinto the deepest layers of meaning to recognize the reality of Divinity (al- mabdā’, prophethood (Ṣirāṭ or nubuwwah and resurrection (ma‘ād and discusses it in a more philosophical manner. This study is an attempt to explore the benefits of these important aspects of religious sources unearthed from Qur’anic injunctions combined with rational principles of philosophical and mystical experiences

Development of Production PVD-AIN Buffer Layer System and Processes to Reduce Epitaxy Costs and Increase LED Efficiency

Energy Technology Data Exchange (ETDEWEB)

Cerio, Frank

2013-09-14

The DOE has set aggressive goals for solid state lighting (SSL) adoption, which require manufacturing and quality improvements for virtually all process steps leading to an LED luminaire product. The goals pertinent to this proposed project are to reduce the cost and improve the quality of the epitaxial growth processes used to build LED structures. The objectives outlined in this proposal focus on achieving cost reduction and performance improvements over state-of-the-art, using technologies that are low in cost and amenable to high efficiency manufacturing. The objectives of the outlined proposal focus on cost reductions in epitaxial growth by reducing epitaxy layer thickness and hetero-epitaxial strain, and by enabling the use of larger, less expensive silicon substrates and would be accomplished through the introduction of a high productivity reactive sputtering system and an effective sputtered aluminum-nitride (AlN) buffer/nucleation layer process. Success of the proposed project could enable efficient adoption of GaN on-silicon (GaN/Si) epitaxial technology on 150mm silicon substrates. The reduction in epitaxy cost per cm{sup 2} using 150mm GaN-on-Si technology derives from (1) a reduction in cost of ownership and increase in throughput for the buffer deposition process via the elimination of MOCVD buffer layers and other throughput and CoO enhancements, (2) improvement in brightness through reductions in defect density, (3) reduction in substrate cost through the replacement of sapphire with silicon, and (4) reduction in non-ESD yield loss through reductions in wafer bow and temperature variation. The adoption of 150mm GaN/Si processing will also facilitate significant cost reductions in subsequent wafer fabrication manufacturing costs. There were three phases to this project. These three phases overlap in order to aggressively facilitate a commercially available production GaN/Si capability. In Phase I of the project, the repeatability of the performance

Cost-Effectiveness Analysis in Comparing Alginate Silver Dressing with Silver Zinc Sulfadiazine Cream in the Treatment of Pressure Ulcers

Directory of Open Access Journals (Sweden)

Apirag Chuangsuwanich

2013-09-01

Full Text Available Background The treatment of pressure ulcers is complicated, given the various wound dressingproducts available. The cost of different treatments varies and the cost-effectiveness of eachproduct has not been thoroughly evaluated. We compare two wound dressing protocolsalginatesilver dressing (AlSD and silver zinc sulfadiazine cream (AgZnSD with regard towound healing and cost-effectivenessMethods Patients with grade III or IV sacral or trochanteric pressure ulcers were eligible forthis prospective, randomized controlled trial. The patients were randomized to receive oneof the two dressings for an eight-week period. The criteria of efficacy were based on thePressure Ulcer Scale for Healing (PUSH scoring tool. The cost of treatment was also assessed.Results Twenty patients (12 women and 8 men were randomly assigned to receive eitherAlSD (n=10 or AgZnSD cream (n=10. The demographic data and wound characteristics werecomparable in the two groups. The two groups showed no significant difference in the reductionof PUSH score, wound size, or volume of exudate. The tissue type score was significantlylower in the AlSD group (3.15±0.68-1.85±0.68 vs. 2.73±0.79-2.2±0.41; P=0.015. The costof treatment was significantly lower in the AlSD group (377.17 vs. 467.74 USD, respectively;P<0.0001.Conclusions Alginate silver dressing could be effectively used in the treatment of grade IIIand IV pressure ulcers. It can improve wound tissue characteristics and is cost-effective.

A united refinement technology for commercial pure Al by Al-10Ti and Al-Ti-C master alloys

International Nuclear Information System (INIS)

Ma Xiaoguang; Liu Xiangfa; Ding Haimin

2009-01-01

Because flake-like TiAl 3 particles in Al-Ti-C master alloys prepared in a melt reaction method dissolve slowly when they are added into Al melt at 720 deg. C, Ti atoms cannot be released rapidly to play the assistant role of grain refinement, leading to a poor refinement efficiency of Al-Ti-C master alloys. A united refinement technology by Al-10Ti and Al-Ti-C master alloys was put forward in this paper. The rational combination of fine blocky TiAl 3 particles in Al-10Ti and TiC particles in Al-Ti-C can improve the nucleation rate of α-Al. It not only improves the grain refinement efficiency of Al-Ti-C master alloys, but also reduces the consumption

Support and Against Historical Cost Accounting: Is it Value Relevance for Decision Making?

Directory of Open Access Journals (Sweden)

Evi Rahmawati

2016-01-01

Full Text Available This paper reviews the issues on the support and criticism of historical cost accounting (HCA and the incremental information content on current cost disclosures. Based on literature review this study find that historical cost is still relevant to use in decision making. Empirical studies show evidence both; supporting historical cost accounting and criticisms against the conventional historical cost based financial statements. Issues on historical cost are raised because of  economic condition, inflation, the change in high tech environment, price movements, and regulators statements. Studies shows that historical cost accounting. over the decade: still have power explanatory for investors, which indicates that its benefits outweigh its cost. However, Barth et al. (1996 provide strong evidence on incremental information of current cost disclosures for certain assets and liabilities. This paper concludes that even there are weaknesses (against HCA, still there are more benefits that we can gain through HCA.

Liquidus projection of the Nb-Cr-Al system near the Al3(Nb,Cr) + Cr(Al,Nb) eutectic region

International Nuclear Information System (INIS)

Souza, S.A.; Ferrandini, P.L.; Nunes, C.A.; Coelho, A.A.; Caram, R.

2006-01-01

The system Nb-Cr-Al was investigated in the region near the Al 3 (Nb,Cr) + Cr(Al,Nb) eutectic and the liquidus projection of that region was determined based on the microstructural characterization of arc melted alloys. The characterization utilized scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), differential thermal analysis (DTA) and X-ray diffraction (XRD). The results allowed one to determine three primary solidification liquidus surfaces ((Cr,Al) 2 Nb, Cr(Al,Nb) and Al 3 (Nb,Cr)), that are originated from the binary systems Cr-Nb, Cr-Al and Al-Nb. It is proposed the occurrence of the invariant reaction L + (Cr,Al) 2 Nb ↔ Al 3 (Nb,Cr) + Cr(Al,Nb) and of a point of minimum, which involves a three phase reaction, L ↔ Al 3 (Nb,Cr) + Cr(Al,Nb). All alloys studied showed formation of the Al 3 (Nb,Cr) + Cr(Al,Nb) eutectic as the last solidification step with Al(Nb)Cr 2 precipitating from Cr(Al,Nb)

Variaciones de voltaje: Mala calidad de la energía

Directory of Open Access Journals (Sweden)

Norberto Rodríguez Barallobre

2011-02-01

Full Text Available Este es el primero de una serie de artículos encaminados a tratar la creciente problemática de la calidadde la energía en las instalaciones industriales debida al incremento del uso de la electrónica y suscomponentes contaminantes de la energía eléctrica entendida como el producto de la onda de corriente yla de voltaje. Además, se ofrece un procedimiento para estimar el costo de las pérdidas técnicas ytecnológicas por concepto de una mala calidad de la energía así como, algunas recomendaciones paramitigar estas pérdidas millonarias en el sector industrial.  This is a first of a series of papers toward to treat the power quality growing problematical in industrialinstallations networks, due to increasing use of electronic and its polluting components, learned as aproduct of the current and voltage wave, Also is offered a procedure to estimate the technical andtechnological losses cost due to the low quality energy, some recommendations to mitigate this millonairelosses in the industrial sector

Deformation processed Al/Ca nano-filamentary composite conductors for HVDC applications

Science.gov (United States)

Czahor, C. F.; Anderson, I. E.; Riedemann, T. M.; Russell, A. M.

2017-07-01

Efficient long-distance power transmission is necessary as the world continues to implement renewable energy sources, often sited in remote areas. Light, strong, high-conductivity materials are desirable for this application to reduce both construction and operational costs. In this study an Al/Ca (11.5% vol.) composite with nano-filamentary reinforcement was produced by powder metallurgy then extruded, swaged, and wire drawn to a maximum true strain of 12.7. The tensile strength increased exponentially as the filament size was reduced to the sub-micron level. In an effort to improve the conductor’s ability to operate at elevated temperatures, the deformation-processed wires were heat-treated at 260°C to transform the Ca-reinforcing filaments to Al2Ca. Such a transformation raised the tensile strength by as much as 28%, and caused little change in ductility, while the electrical conductivity was reduced by only 1% to 3%. Al/Al2Ca composites are compared to existing conductor materials to show how implementation could affect installation and performance.

A united refinement technology for commercial pure Al by Al-10Ti and Al-Ti-C master alloys

Energy Technology Data Exchange (ETDEWEB)

Ma Xiaoguang [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Liu Xiangfa [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China)], E-mail: xfliu@sdu.edu.cn; Ding Haimin [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China)

2009-03-05

Because flake-like TiAl{sub 3} particles in Al-Ti-C master alloys prepared in a melt reaction method dissolve slowly when they are added into Al melt at 720 deg. C, Ti atoms cannot be released rapidly to play the assistant role of grain refinement, leading to a poor refinement efficiency of Al-Ti-C master alloys. A united refinement technology by Al-10Ti and Al-Ti-C master alloys was put forward in this paper. The rational combination of fine blocky TiAl{sub 3} particles in Al-10Ti and TiC particles in Al-Ti-C can improve the nucleation rate of {alpha}-Al. It not only improves the grain refinement efficiency of Al-Ti-C master alloys, but also reduces the consumption.

Melting and casting of FeAl-based cast alloy

Energy Technology Data Exchange (ETDEWEB)

Sikka, V.K. [Oak Ridge National Lab., TN (United States); Wilkening, D. [Columbia Falls Aluminum Co., Columbia Falls, MT (United States); Liebetrau, J.; Mackey, B. [AFFCO, L.L.C., Anaconda, MT (United States)

1998-11-01

The FeAl-based intermetallic alloys are of great interest because of their low density, low raw material cost, and excellent resistance to high-temperature oxidation, sulfidation, carburization, and molten salts. The applications based on these unique properties of FeAl require methods to melt and cast these alloys into complex-shaped castings and centrifugal cast tubes. This paper addresses the melting-related issues and the effect of chemistry on the microstructure and hardness of castings. It is concluded that the use of the Exo-Melt{trademark} process for melting and the proper selection of the aluminum melt stock can result in porosity-free castings. The FeAl alloys can be melted and cast from the virgin and revert stock. A large variation in carbon content of the alloys is possible before the precipitation of graphite flakes occurs. Titanium is a very potent addition to refine the grain size of castings. A range of complex sand castings and two different sizes of centrifugal cast tubes of the alloy have already been cast.

Interrelaciones entre nutrición y reproducción. Análisis y experiencias de campo

Directory of Open Access Journals (Sweden)

Oscar Fernando Ospina Rivera

2007-06-01

Full Text Available Todos los días se deben tomar decisiones bien sea porque se es el gerente o dueño de una empresa ganadera, o su profesional asesor, el problema no está en “que se tomen” estas decisiones, sino, en “cómo se toman”, bajo qué lupa se analizó el problema y se generaron los criterios y recomendaciones para la toma de estas decisiones. Al momento de enfrentar un problema se tienen dos posibilidades, o se aborda dentro de un enfoque reduccionista (clásico o mediante un enfoque integracionista (Teoría General de Sistemas, en el primero se va a tratar de generar conocimiento a través del análisis de las partes de manera aislada y en el segundo se va a tratar de generar conocimiento a través del análisis de las interacciones entre las partes. En el presente artículo se hace referencia al abordaje de los problemas desde el segundo punto de vista, como lo plantea la Teoría General de Sistemas, explorando la ganadería en su complejidad y multifactoriedad vista como un sistema de producción, concentrando el análisis a los subsistemas nutrición, reproducción y sus interacciones.

Cost-Effectiveness of Pazopanib Versus Sunitinib for Renal Cancer in the United States.

Science.gov (United States)

Benedict, Agnes; Ramaswamy, Krishnan; Sandin, Rickard

2015-09-01

We write to comment on a recently published study by Delea et al. in the January 2015 issue of JMCP that evaluated the cost-effectiveness (CE) of sunitinib (SU) versus pazopanib (PAZ) as first-line treatment for metastatic renal cell carcinoma (mRCC) from a U.S. third-party payer perspective.1 This analysis was based on COMPARZ and PISCES, clinical trials that compared SU and PAZ2,3 and led the authors to conclude that PAZ is cost-effective (in fact, dominant, according to the base-case results) compared with SU. Such assessment of economic value is clearly important for deciding between therapies to ensure fair access; therefore, we welcome a comparative evaluation of SU and PAZ. However, we believe that some of the key assumptions and inputs used in the model by Delea et al. render their results and conclusions invalid.  Best practice requires that results from a health economic model should reflect the most likely outcomes based on sound methodology and robust evidence for its inputs, as recommended by the International Society of Pharmacoeconomics and Outcomes Research (ISPOR).4 Here, we focus on 2 key areas (utilities and survival modeling) where, in our view, the analysis by Delea et al. falls short of this standard, and a third area (treatment costs) where the basis for the data derived is unclear.

Use of low-cost aluminum in electric energy production

Science.gov (United States)

Zhuk, Andrey Z.; Sheindlin, Alexander E.; Kleymenov, Boris V.; Shkolnikov, Eugene I.; Lopatin, Marat Yu.

Suppression of the parasitic corrosion while maintaining the electrochemical activity of the anode metal is one of the serious problems that affects the energy efficiency of aluminum-air batteries. The need to use high-purity aluminum or special aluminum-based alloys results in a significant increase in the cost of the anode, and thus an increase in the total cost of energy generated by the aluminum-air battery, which narrows the range of possible applications for this type of power source. This study considers the process of parasitic corrosion as a method for hydrogen production. Hydrogen produced in an aluminum-air battery by this way may be further employed in a hydrogen-air fuel cell (Hy-air FC) or in a heat engine, or it may be burnt to generate heat. Therefore, anode materials may be provided by commercially pure aluminum, commercially produced aluminum alloys, and secondary aluminum. These materials are much cheaper and more readily available than special anode alloys of aluminum and high-purity aluminum. The aim of present study is to obtain experimental data for comparison of energy and cost parameters of some commercially produced aluminum alloys, of high-purity aluminum, and of a special Al-ln anode alloy in the context of using these materials as anodes for an Al-air battery and for combined production of electrical power and hydrogen.

Cost-Reduction Roadmap for Residential Solar Photovoltaics (PV), 2017-2030

Energy Technology Data Exchange (ETDEWEB)

Cook, Jeffrey J. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Ardani, Kristen B. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Margolis, Robert M. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Fu, Ran [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-01-03

The installed cost of solar photovoltaics (PV) has fallen rapidly in recent years and is expected to continue declining in the future. In this report, we focus on the potential for continued PV cost reductions in the residential market. From 2010 to 2017, the levelized cost of energy (LCOE) for residential PV declined from 52 cents per kilowatt-hour (cents/kWh) to 16 cents/kWh (Fu et al. 2017). The U.S. Department of Energy's (DOE's) Solar Energy Technologies Office (SETO) recently set new LCOE targets for 2030, including a target of 5 cents/kWh for residential PV. We present a roadmap for achieving the SETO 2030 residential PV target. Because the 2030 target likely will not be achieved under business-as-usual trends (NREL 2017), we examine two key market segments that demonstrate significant opportunities for cost savings and market growth: installing PV at the time of roof replacement and installing PV as part of the new home construction process. Within both market segments, we identify four key cost-reduction opportunities: market maturation, business model integration, product innovation, and economies of scale. To assess the potential impact of these cost reductions, we compare modeled residential PV system prices in 2030 to the National Renewable Energy Laboratory's (NREL's) quarter one 2017 (Q1 2017) residential PV system price benchmark (Fu et al. 2017). We use a bottom-up accounting framework to model all component and project-development costs incurred when installing a PV system. The result is a granular accounting for 11 direct and indirect costs associated with installing a residential PV system in 2030. All four modeled pathways demonstrate significant installed-system price savings over the Q1 2017 benchmark, with the visionary pathways yielding the greatest price benefits. The largest modeled cost savings are in the supply chain, sales and marketing, overhead, and installation labor cost categories. When we translate these

United modification of Al-24Si alloy by Al-P and Al-Ti-C master alloys

Institute of Scientific and Technical Information of China (English)

韩延峰; 刘相法; 王海梅; 王振卿; 边秀房; 张均艳

2003-01-01

The modification effect of a new type of Al-P master alloy on Al-24Si alloys was investigated. It is foundthat excellent modification effect can be obtained by the addition of this new type of A1-P master alloy into Al-24Simelt and the average primary Si grain size is decreased below 47 μm from original 225 μm. It is also found that theTiC particles in the melt coming from Al8Ti2C can improve the modification effect of the Al-P master alloy. Whenthe content of TiC particles in the Al-24Si melt is 0.03 %, the improvement reaches the maximum and keeps steadywith increasing content of TiC particles. Modification effect occurs at 50 min after the addition of the Al-P master al-loy and TiC particles, and keeps stable with prolonging holding time.

Insurance cost of Swedish nuclear power plants

International Nuclear Information System (INIS)

Kaellstrand, Aasa.

1992-01-01

What happens if a reactor accident occurs? Can victims of a nuclear accident be compensated for losses? The rights of a victim of a nuclear accident to be compensated for losses are governed by international conventions. These conventions make the licensee of a nuclear plant strictly liable. However, the maximum amount of compensation is limited. In Sweden the total liability of the plant-owner is maximized to 1.2 million Swedish Crowns, that is 0.02 oere/kWh. After the accidents of Harrisburg (1979) and Chernobyl (1986), it has become clear that the amounts of the various conventions are not at all sufficient to cover the damages caused by such an accident. In spite of these facts, there are a large number of reliable sources, who think that the insurance costs are negligible in the cost of production. A cost-benefit analysis based on a study performed by Ottinger et al. in 'Environmental costs of electricity' is therefore adopted to derive the costs of the external effects of nuclear plant operation and from releases to the environment during operation. The environmental externality costs of Swedish nuclear power plant operations are in this report estimated to 18.3 oere/kWh. This figure can be compared to the insurance cost, which for the present is 0.02 oere/kWh. The 'real' insurance cost including the external effects is calculated to approximately 1.12 billion Swedish Crowns] That is 900 times larger than the insurance premium, which the licensee of a nuclear plant faces] (au)

Nanoporous Al sandwich foils using size effect of Al layer thickness during Cu/Al/Cu laminate rolling

Science.gov (United States)

Yu, Hailiang; Lu, Cheng; Tieu, A. Kiet; Li, Huijun; Godbole, Ajit; Kong, Charlie

2018-06-01

The roll bonding technique is one of the most widely used methods to produce metal laminate sheets. Such sheets offer interesting research opportunities for both scientists and engineers. In this paper, we report on an experimental investigation of the 'thickness effect' during laminate rolling for the first time. Using a four-high multifunction rolling mill, Cu/Al/Cu laminate sheets were fabricated with a range of thicknesses (16, 40, 70 and 130 μm) of the Al layer. The thickness of the Cu sheets was a constant 300 μm. After rolling, TEM images show good bonding quality between the Cu and Al layers. However, there are many nanoscale pores in the Al layer. The fraction of nanoscale pores in the Al layer increases with a reduction in the Al layer thickness. The finite element method was used to simulate the Cu/Al/Cu rolling process. The simulation results reveal the effect of the Al layer thickness on the deformation characteristics of the Cu/Al/Cu laminate. Finally, we propose that the size effect of the Al layer thickness during Cu/Al/Cu laminate rolling may offer a method to fabricate 'nanoporous' Al sandwich laminate foils. Such foils can be used in electromagnetic shielding of electrical devices and noisy shielding of building.

Structural stability and electronic properties of AlCu3, AlCu2Zr in AlZr3: Stabilnost strukture in elektronske lastnosti AlCu3, AlCu2Zr in AlZr3:

OpenAIRE

Cheng, Rong; Wu, Xiao-Yu

2013-01-01

First-principles calculations were performed to study the alloying stability and electronic structure of the Al-based intermetallic compounds AlCusub3, AlCusub{2}Zr and AlZrsub3. The results show that the lattice parameters obtained after the full relaxation of the crystalline cells are consistent with the experimental data, and these intermetallics have a strong alloying ability and structural stability due to their negative formation energies and their cohesive energies. A further analysis ...

COST MEASUREMENT AND COST MANAGEMENT IN TARGET COSTING

Directory of Open Access Journals (Sweden)

Moisello Anna Maria

2012-07-01

Full Text Available Firms are coping with a competitive scenario characterized by quick changes produced by internationalization, concentration, restructuring, technological innovation processes and financial market crisis. On the one hand market enlargement have increased the number and the segmentation of customers and have raised the number of competitors, on the other hand technological innovation has reduced product life cycle. So firms have to adjust their management models to this scenario, pursuing customer satisfaction and respecting cost constraints. In a context where price is a variable fixed by the market, firms have to switch from the cost measurement logic to the cost management one, adopting target costing methodology. The target costing process is a price driven, customer oriented profit planning and cost management system. It works, in a cross functional way, from the design stage throughout all the product life cycle and it involves the entire value chain. The process implementation needs a costing methodology consistent with the cost management logic. The aim of the paper is to focus on Activity Based Costing (ABC application to target costing process. So: -it analyzes target costing logic and phases, basing on a literary review, in order to highlight the costing needs related to this process; -it shows, through a numerical example, how to structure a flexible ABC model – characterized by the separation between variable, fixed in the short and fixed costs - that effectively supports target costing process in the cost measurement phase (drifting cost determination and in the target cost alignment; -it points out the effectiveness of the Activity Based Costing as a model of cost measurement applicable to the supplier choice and as a support for supply cost management which have an important role in target costing process. The activity based information allows a firm to optimize the supplier choice by following the method of minimizing the

a Precise, Low-Cost Rtk Gnss System for Uav Applications

Science.gov (United States)

Stempfhuber, W.; Buchholz, M.

2011-09-01

High accuracy with real-time positioning of moving objects has been considered a standard task of engineering geodesy for 10 to 15 years. An absolute positioning accuracy of 1-3 cm is generally possible worldwide and is further used in many areas of machine guidance (machine control and guidance), and farming (precision farming) as well as for various special applications (e.g. railway trolley, mining, etc.). The cost of the measuring instruments required for the use of geodetic L1/L2 receivers with a local reference station amounts to approximately USD 30,000 to 50,000. Therefore, dual frequency RTK GNSS receivers are not used in the mass market. Affordable GPS/GNSS modules have already reached the mass market in various areas such as mobile phones, car navigation, the leisure industry, etc. Kinematic real-time positioning applications with centimetre or decimetre levels could also evolve into a mass product. In order for this to happen, the costs for such systems must lie between USD 1,000 to 2,000. What exactly low-cost means is determined by the precise specifications of the given individual application. Several university studies in geodesy focus on the approach of high-accuracy positioning by means of single frequency receivers for static applications [e.g. GLABSCH et. al. 2009, SCHWIEGER and GLÄSER 2005, ALKAN 2010, REALINI et. al. 2010, KORTH and HOFMANN 2011]. Although intelligent approaches have been developed that compute a trajectory in the post-processing mode [REALINI et. al., 2010], at present, there are only a very few GNSS Low-Cost Systems that enable real-time processing. This approach to precise position determination by means of the computation of static raw data with single frequency receivers is currently being explored in a research project at the Beuth Hochschule für Technik Berlin - and is being further developed for kinematic applications. The project is embedded in the European Social Fund. It is a follow-up project in the area of

DC-magnetron sputtering of ZnO:Al films on (00.1)Al2O3 substrates from slip-casting sintered ceramic targets

International Nuclear Information System (INIS)

Miccoli, I.; Spampinato, R.; Marzo, F.; Prete, P.; Lovergine, N.

2014-01-01

Highlights: • ZnO:Al was DC-sputtered on sapphire >350 °C by slip-casting sintered AZO target. • Films are highly (00.1)-oriented, smooth and transparent in the NIR–visible range. • Films growth rate decreases with temperature, while their grain size increases. • A high temperature reduction for sticking coefficients of impinging species is proved. • We prove that Thornton model does not apply to high-temperature DC-sputtered ZnO. - Abstract: High (>350 °C) temperature DC-sputtering deposition of ZnO:Al thin films onto single-crystal (00.1) oriented Al 2 O 3 (sapphire) substrates is reported, using a ultrahigh-density, low-resistivity and low-cost composite ceramic target produced by slip-casting (pressureless) sintering of ZnO–Al 2 O 3 (AZO) powders. The original combination of high-angle θ–2θ (Bragg–Brentano geometry) X-ray diffraction with low angle θ–2θ X-ray reflectivity (XRR) techniques allows us to define the AZO target composition and investigate the structural properties and surface/interface roughness of as-sputtered ZnO:Al films; besides, the growth dynamics of ZnO:Al is unambiguously determined. The target turned out composed of the sole wurtzite ZnO and spinel ZnAl 2 O 4 phases. X-ray diffraction analyses revealed highly (00.1)-oriented (epitaxial) ZnO:Al films, the material mean crystallite size being in the 13–20 nm range and increasing with temperature between 350 °C and 450 °C, while the film growth rate (determined via XRR measurements) decreases appreciably. XRR spectra also allowed to determine rms surface roughness <1 nm for present films and showed ZnO:Al density changes by only a few percent between 350 °C and 450 °C. The latter result disproves the often-adopted Thornton model for the description of the sputter-grown ZnO films and instead points out toward a reduction of the sticking coefficients of impinging species, as the main origin of film growth rate and grain size dependence with temperature. ZnO:Al

Comparative analysis of Nb and Ti addition in the Cu-11,8%wt.Al-0,5%wt.Be e Cu-11,8%wt.Al-3,0%wt.Ni shape memory alloy

International Nuclear Information System (INIS)

Silva Junior, M.Q. da; Oliveira, G.D. de

2014-01-01

The system of the Cu-Al alloys shape memory alloy have been the subject of many studies due to a wide range of possible applications and relatively low cost, and the chemical composition of the main factors that determine the properties of these properties. This work analyzed the influence of Nb and Ti elements in Cu-11,8Al-0,5Be and Cu-11,8Al-3,0Ni alloy. The alloys are obtained by melting and passed through homogenizing heat treatment followed by water quenching at 30°C. The samples were characterized by Microscopy Optical, X-ray Diffraction and Microhardness testing. The alloys showed fine precipitates of second phase homogeneously distributed in the matrix that provides improvement in the properties of these alloys. (author)

The Limited Role of Number of Nested Syntactic Dependencies in Accounting for Processing Cost: Evidence from German Simplex and Complex Verbal Clusters

Directory of Open Access Journals (Sweden)

Markus Bader

2018-01-01

Full Text Available This paper presents three acceptability experiments investigating German verb-final clauses in order to explore possible sources of sentence complexity during human parsing. The point of departure was De Vries et al.'s (2011 generalization that sentences with three or more crossed or nested dependencies are too complex for being processed by the human parsing mechanism without difficulties. This generalization is partially based on findings from Bach et al. (1986 concerning the acceptability of complex verb clusters in German and Dutch. The first experiment tests this generalization by comparing two sentence types: (i sentences with three nested dependencies within a single clause that contains three verbs in a complex verb cluster; (ii sentences with four nested dependencies distributed across two embedded clauses, one center-embedded within the other, each containing a two-verb cluster. The results show that sentences with four nested dependencies are judged as acceptable as control sentences with only two nested dependencies, whereas sentences with three nested dependencies are judged as only marginally acceptable. This argues against De Vries et al.'s (2011 claim that the human parser can process no more than two nested dependencies. The results are used to refine the Verb-Cluster Complexity Hypothesis of Bader and Schmid (2009a. The second and the third experiment investigate sentences with four nested dependencies in more detail in order to explore alternative sources of sentence complexity: the number of predicted heads to be held in working memory (storage cost in terms of the Dependency Locality Theory [DLT], Gibson, 2000 and the length of the involved dependencies (integration cost in terms of the DLT. Experiment 2 investigates sentences for which storage cost and integration cost make conflicting predictions. The results show that storage cost outweighs integration cost. Experiment 3 shows that increasing integration cost in sentences

User’s Guide for Naval Material Command’s Life Cycle Cost (FLEX) Model.

Science.gov (United States)

1982-04-01

WBS) of both simple and complex programs. o The model can use a different cost estimating procedure for each element of the CBS (i.e., algorithm and...cycle. (yrs) E-15 I .. 22 Govenm.n: .Al. Scale Devel.-,menz - cstr Def Lntion: .he costs included in t.his subcategory include: 1.22C0 ?roject I&nagement

La filosofía práctica y el método dialéctico aristotélicos: ¿Es la argumentación práctica una especie de dialéctica?

OpenAIRE

Bieda, Esteban

2012-01-01

Es sabido que Aristóteles suele comenzar la mayor parte de sus investigaciones con un relevamiento de posiciones y/o concepciones previas relativas al tema a tratar. En el presente trabajo trataremos de mostrar que tanto las referencias a autores anteriores como a las opiniones corrientes sobre el tema tratado responden a las exigencias de cierto proceder metódico que las necesita como elementos constitutivos. Nuestra tarea concreta consistirá en intentar develar el valor metódicoepistemológi...

A cost/schedule and control system for the environmental restoration program Albuquerque Field Office

International Nuclear Information System (INIS)

Fiske, Wanda S.; Bischoff, Edward L.; Rea, Kenneth H.; Dwain Farley, P.; Biedermann, Charles A.

1992-01-01

The Department of Energy (DOE) Field Office Albuquerque (AL), Environmental Restoration Project Office (ERPO), has developed a project management system used to plan, document, and control Environmental Restoration (ER) work at eight installations and one superfund site managed by AL. This system emphasizes control of the cost, schedule, and technical elements of the Program. It supports programmatic documentation such as the Environmental Restoration/Waste Management Five-Year Plan, Site Specific Plan, and budget requests. The System provides information used to manage the ER Program at all levels of management (i.e., from low-level day-to-day activities to high-level upper management). The System requires substantial effort to ensure reliability; however, the benefit to ERPO is an effective, proactive project management tool. This paper provides an overview of the ERPO System, an explanation of how it is implemented, and lessons learned from this process. Application of the System to cost estimating, annual and five-year budget preparation, resource projections, scheduling, and cost/schedule performance measurement is discussed. Also discussed are cost/schedule review procedures, along with variance identification and resolution. Examples are taken from the Pinellas ER Program. (author)

Synthesis and fabrication of MgAl2O4 ceramic foam via a simple, low-cost and eco-friendly method

Directory of Open Access Journals (Sweden)

Shuvendu Tripathy

2016-06-01

Full Text Available The MgAl2O4 nanocrystalline powder was synthesized using naturally available egg white and inexpensive metal nitrate salts. During this process, the freshly extracted egg white was mixed with metal nitrate salt and subsequently heated at 350 °C in a pit furnace. The entire dehydration of the aqueous solution thus facilitates the low-density fluffy mass. From TGDTG results, it was observed that maximum decomposition of the precursors occurred below 600 °C. Therefore, the calcination temperature of as-synthesized powder was set at 600 °C. The MgAl2O4 bulk ceramic foam was fabricated by dispersing different loading of MgAl2O4 nanoparticles in the egg white, and then coating on polyurethane sponge prior to drying and sintering at a higher temperature. The ceramic suspensions exhibit a typical shear thinning behavior, and its viscosity was found to be significantly influenced by MgAl2O4 powder content. An optimum loading of 40 wt% MgAl2O4 nanoparticles in the egg white was found to show maximum porosity up to 90%. The obtained ceramic foam has potential applications in catalysis, absorption and sensor.

Low-Cost Photolithographic Fabrication of Nanowires and Microfilters for Advanced Bioassay Devices

Directory of Open Access Journals (Sweden)

Nhi M. Doan

2015-03-01

Full Text Available Integrated microfluidic devices with nanosized array electrodes and microfiltration capabilities can greatly increase sensitivity and enhance automation in immunoassay devices. In this contribution, we utilize the edge-patterning method of thin aluminum (Al films in order to form nano- to micron-sized gaps. Evaporation of high work-function metals (i.e., Au, Ag, etc. on these gaps, followed by Al lift-off, enables the formation of electrical uniform nanowires from low-cost, plastic-based, photomasks. By replacing Al with chromium (Cr, the formation of high resolution, custom-made photomasks that are ideal for low-cost fabrication of a plurality of array devices were realized. To demonstrate the feasibility of such Cr photomasks, SU-8 micro-pillar masters were formed and replicated into PDMS to produce micron-sized filters with 3–4 µm gaps and an aspect ratio of 3. These microfilters were capable of retaining 6 µm beads within a localized site, while allowing solvent flow. The combination of nanowire arrays and micro-pillar filtration opens new perspectives for rapid R&D screening of various microfluidic-based immunoassay geometries, where analyte pre-concentration and highly sensitive, electrochemical detection can be readily co-localized.

/Cu-Al System

Science.gov (United States)

Kish, Orel; Froumin, Natalya; Aizenshtein, Michael; Frage, Nachum

2014-05-01

Wettability and interfacial interaction of the Ta2O5/Cu-Al system were studied. Pure Cu does not wet the Ta2O5 substrate, and improved spreading is achieved when relatively a high fraction of the active element (~40 at.% Al) was added. The Al2O3 and AlTaO4 phases were observed at the Ta2O5/Cu-Al interface. A thermodynamic evaluation allowed us to suggest that the lack of wetting bellow 40 at.% Al is due to the presence of a native oxide, which covers the drop. The conditions of the native oxide decomposition and the formation of the volatile Al2O suboxide strongly depend on the vacuum level during sessile drop experiments and the composition of the Cu-Al alloy. In our case, Al contents greater than 40% provides thermodynamic conditions for the formation of Al2O (as a result of Al reaction with Al2O3) and the drop spreading. It was suggested that the final contact angle in the Ta2O5/Cu-Al system (50°) is determined by Ta adsorption on the newly formed alumina interlayer.

76 FR 13615 - B&B Manufacturing Site; Mobile, Mobile County, AL; Notice of Settlement

Science.gov (United States)

2011-03-14

... settlement for reimbursement of past response costs concerning the B&B Manufacturing Site located in Mobile, Mobile County, Alabama for publication. DATES: The Agency will consider public comments on the settlement... Site; Mobile, Mobile County, AL; Notice of Settlement AGENCY: Environmental Protection Agency. ACTION...

(Super Variable Costing-Throughput Costing)

OpenAIRE

Çakıcı, Cemal

2006-01-01

(Super Variable Costing-Throughput Costing) The aim of this study is to explain the super-variable costing method which is a new subject in cost and management accounting and to show it’s working practicly.Shortly, super-variable costing can be defined as a costing method which is use only direct material costs in calculate of product costs and treats all costs except these (direct labor and overhead) as periad costs or operating costs.By using super-variable costing method, product costs ar...

A reply to “Historical construction costs of global nuclear power reactors”

International Nuclear Information System (INIS)

Koomey, Jonathan; Hultman, Nathan E.; Grubler, Arnulf

2017-01-01

present data on the overnight costs of more than half of nuclear reactors built worldwide since the beginning of the nuclear age. The authors claim that this consolidated data set offers more accurate insights than previous country-level assessments. Unfortunately, the authors make analytical choices that mask nuclear power's real construction costs, cherry pick data, and include misleading data on early experimental and demonstration reactors. For those reasons, serious students of such issues should look elsewhere for guidance about understanding the true costs of nuclear power. - Highlights: • claim to accurately assess nuclear plant costs over time. • The authors err by relying on overnight costs, which exclude interest. • The authors cherry pick data (e.g, ignoring problems with French nuclear data). • The article's cherry picked data don’t even support the article's own conclusions. • Lovering et al. is not a reliable source for costs of nuclear power.

Transparent field-effect transistors based on AlN-gate dielectric and IGZO-channel semiconductor

International Nuclear Information System (INIS)

Besleaga, C.; Stan, G.E.; Pintilie, I.; Barquinha, P.; Fortunato, E.; Martins, R.

2016-01-01

Highlights: • TFTs based on IGZO channel semiconductor and AlN gate dielectric were fabricated. • AlN films – a viable and cheap gate dielectric alternative for transparent TFTs. • Influence of gate dielectric layer thickness on TFTs electrical characteristics. • No degradation of AlN gate dielectric was observed during devices stress testing. - Abstract: The degradation of thin-film transistors (TFTs) caused by the self-heating effect constitutes a problem to be solved for the next generation of displays. Aluminum nitride (AlN) is a viable alternative for gate dielectric of TFTs due to its good thermal conductivity, matching coefficient of thermal expansion to indium–gallium–zinc-oxide, and excellent stability at high temperatures. Here, AlN thin films of different thicknesses were fabricated by a low temperature reactive radio-frequency magnetron sputtering process, using a low cost, metallic Al target. Their electrical properties have been thoroughly assessed. Furthermore, the 200 nm and 500 nm thick AlN layers have been integrated as gate-dielectric in transparent TFTs with indium–gallium–zinc-oxide as channel semiconductor. Our study emphasizes the potential of AlN thin films for transparent electronics, whilst the functionality of the fabricated field-effect transistors is explored and discussed.

Transparent field-effect transistors based on AlN-gate dielectric and IGZO-channel semiconductor

Energy Technology Data Exchange (ETDEWEB)

Besleaga, C.; Stan, G.E.; Pintilie, I. [National Institute of Materials Physics, 405A Atomistilor, 077125 Magurele-Ilfov (Romania); Barquinha, P.; Fortunato, E. [CENIMAT/I3N, Departamento de Ciência dos Materiais, Faculdade de Ciências e Tecnologia, FCT, Universidade Nova de Lisboa, and CEMOP-UNINOVA, 2829-516 Caparica (Portugal); Martins, R., E-mail: rm@uninova.pt [CENIMAT/I3N, Departamento de Ciência dos Materiais, Faculdade de Ciências e Tecnologia, FCT, Universidade Nova de Lisboa, and CEMOP-UNINOVA, 2829-516 Caparica (Portugal)

2016-08-30

Highlights: • TFTs based on IGZO channel semiconductor and AlN gate dielectric were fabricated. • AlN films – a viable and cheap gate dielectric alternative for transparent TFTs. • Influence of gate dielectric layer thickness on TFTs electrical characteristics. • No degradation of AlN gate dielectric was observed during devices stress testing. - Abstract: The degradation of thin-film transistors (TFTs) caused by the self-heating effect constitutes a problem to be solved for the next generation of displays. Aluminum nitride (AlN) is a viable alternative for gate dielectric of TFTs due to its good thermal conductivity, matching coefficient of thermal expansion to indium–gallium–zinc-oxide, and excellent stability at high temperatures. Here, AlN thin films of different thicknesses were fabricated by a low temperature reactive radio-frequency magnetron sputtering process, using a low cost, metallic Al target. Their electrical properties have been thoroughly assessed. Furthermore, the 200 nm and 500 nm thick AlN layers have been integrated as gate-dielectric in transparent TFTs with indium–gallium–zinc-oxide as channel semiconductor. Our study emphasizes the potential of AlN thin films for transparent electronics, whilst the functionality of the fabricated field-effect transistors is explored and discussed.

Metodologi Kitab Ma‘alim al-Tanzil Karya Al-Bagawiy

Directory of Open Access Journals (Sweden)

M. Rusydi Khalid

2017-12-01

This study aims to describe the metodology of Ma'a> lim al-tanzi>l book by al-Bagawi. The book is one of the books of exegesis written on the basis of hadith, which by the commentary scholars recognized avoided from heresy and weak hadith. The author of this book is Imam Abu Humaid Hussein bin Mas‘u>d al-Farra>’ Al-Bagawi al-Syafi‘i>, died in the year 510 H. This exegesis book combines the interpretation of the companions, tabi‘i>n, and tabi‘i> tabi‘i>n. Interpretation is broken down with easy, simple, and concise diction choices. The stoning of the interpretation of the salaf scholars without mentioning the sanad as already mentioned in the introduction to his book. This book was first printed in one edition with the exegesis book of Ibn Kas}i>r and al-kha>zin. This book interprets the Qur'an analytically from the beginning to the end of the surah by using the method of interpretation based on the hadith, namely by mentioning the arguments of the hadith sahih, the fatwa of the companions and the tabi‘i>n. The characteristic or purpose of this book is fiqh oriented, which tends to the Shafi‘i fiqh.   Abstrak Tulisan ini mendeskripsikan metode penafsiran dalam kitab Ma’a>lim al-tanzi>l karya al-bagawi. Kitab tafsir ini merupakan salah satu di antara kitab-kitab tafsir yang ditulis berdasarkan riwayat, yang oleh para ulama tafsir diakui terhindar dari bid’ah dan hadis dhaif (lemah. Penulis buku ini adalah Imam Abu Muhammad Husain bin Mas‘u>d al-Farra>‘ al-Bagawi al-Syafi‘i>, wafat pada tahun 510 H. Kitab ini adalah kitab pertengahan yang mengutip penafsiran para Sahabat, ta>bi‘i>n, dan tabi‘i ta>bi‘i>n. Penafsiran diuraikan dengan pilihan diksi yang mudah, sederhana, dan ringkas. Penukilan dari interpretasi ulama salaf tanpa menyebutkan sanad karena telah disebutkan dalam pendahuluan bukunya. Buku ini pertama kali dicetak dalam satu edisi dengan tafsir Ibn Kas\\i>r dan tafsir al-Kha>zin. Kitab ini menafsirkan al-Qur’an secara

ALS Association

Science.gov (United States)

... toward a world without ALS! Walk to Defeat ALS® Walk to Defeat ALS® draws people of all ... We need your help. I Will Advocate National ALS Registry The National ALS Registry is a congressionally ...

AlN nanoparticle-reinforced nanocrystalline Al matrix composites: Fabrication and mechanical properties

International Nuclear Information System (INIS)

Liu, Y.Q.; Cong, H.T.; Wang, W.; Sun, C.H.; Cheng, H.M.

2009-01-01

To improve the specific strength and stiffness of Al-based composites, AlN/Al nanoparticles were in-situ synthesized by arc plasma evaporation of Al in nitrogen atmosphere and consolidated by hot-pressing to fabricate AlN nanoparticle-reinforced nanocrystalline Al composites (0-39 vol.% AlN). Microstructure characterization shows that AlN nanoparticles homogeneously distribute in the matrix of Al nanocrystalline, which forms atomically bonded interfaces of AlN/Al. The hardness and the elastic modulus of the nanocomposite have been improved dramatically, up to 3.48 GPa and 142 GPa, respectively. Such improvement is believed to result from the grain refinement strengthening and the interface strengthening (load transfer) between the Al matrix and AlN nanoparticles

Effect of wrapped Zn plate on the densification of Al-MWCNTs composites produced by cold pressing and liquid phase sintering

Energy Technology Data Exchange (ETDEWEB)

Joo, M.R. [Department of Materials Science and Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Choi, H.J. [School of Advanced Materials Engineering, Kookmin University, Seoul 136-702 (Korea, Republic of); Shin, S.E. [Department of Materials Science and Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Bae, D.H., E-mail: donghyun@yonsei.ac.kr [Department of Materials Science and Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of)

2016-09-30

To produce highly dense and cost-effective Al-multi-walled carbon nanotube (Al-MWCNT) composites, the composite powders are wrapped by a Zn plate and then cold-pressed. The green compacts are then sintered at 550 °C, which shows ~99%density after sintering for 24 h. During sintering, Zn atoms fill the voids at the powder boundaries by capillary action and are then dissolved into the Al matrix because of the high solubility of Zn in Al, thus assisting densification of the composite powder. The Al/Zn-based composites containing 4 vol% MWCNTs show compressive yield strength (~380 MPa) and high work hardening capacity.

Preparation of Al-Mg Alloy Electrodes by Using Powder Metallurgy and Their Application for Hydrogen Production

Directory of Open Access Journals (Sweden)

Wen-Nong Hsu

2014-01-01

Full Text Available The choice of an electrode is the most critical parameter for water electrolysis. In this study, powder metallurgy is used to prepare aluminum-magnesium (Al-Mg alloy electrodes. In addition to pure Mg and Al electrodes, five Al-Mg alloy electrodes composed of Al-Mg (10 wt%, Al-Mg (25 wt%, Al-Mg (50 wt%, and Al-Mg (75 wt% were prepared. In water electrolysis experiments, the pure Al electrode exhibited optimal electrolytic efficiency. However, the Al-Mg (25 wt% alloy was the most efficient when the anticorrosion effect and materials costs were considered. In this study, an ultrasonic field was applied to the electrolysis cell to improve its efficiency. The results revealed that the current increased by approximately 23.1% when placed in a 30 wt% KOH solution under the ultrasonic field. Electrochemical polarization impedance spectroscopy (EIS was employed to evaluate the effect of the ultrasonic field on the reduction of polarization resistance. The results showed that the concentration impedance in the 30 wt% KOH electrolyte decreased markedly by 44%–51% Ω.

Comparison of one and two-neutron transfer near the Coulomb barrier for the 27Al(18O, 16O)29Al, 27Al(18O, 17O)28Al and 27Al(13C, 12C)28Al reactions

International Nuclear Information System (INIS)

Schiller, S.A.; Eck, J.S.

1975-01-01

Total reaction cross sections for the transfer reactions 27 Al( 18 O, 16 O) 29 Al, 27 Al( 18 O, 17 O) 28 Al and 27 Al( 13 C, 12 C) 28 Al are reported for center-of-mass energies between 13 and 20 MeV for 18 O projectiles and between 11 and 17.5 MeV for 13 C projectiles. The reaction products, 29 Al, and 28 Al, beta decay to 29 Si and 28 Si, respectively, and the subsequent γ decays of 29 Si and 28 Si were measured. Due to the relatively long beta decay half lives, data were taken in a beam-off mode, resulting in very clean spectra. Total cross sections were calculated and compared with a theoretical model for barrier penetration proposed by C.Y. Wong. Differences between 18 O induced one and two-neutron total transfer reaction cross sections are discussed. (orig.) [de

Morphology, microstructure, and hardness of titanium (Ti-6Al-4V) blocks deposited by wire-feed additive layer manufacturing (ALM)

International Nuclear Information System (INIS)

Brandl, Erhard; Schoberth, Achim; Leyens, Christoph

2012-01-01

Highlights: ► The microstructure and hardness of deposited Ti-6Al-4V blocks are investigated. ► Hardness is influenced by post heat treatment rather than by process parameters. ► Microstructure within the prior β-grains varies to some extent from grain to grain. ► A 600 °C/4 h treatment significantly increased the average hardness. - Abstract: Additive layer manufacturing offers a potential for time and cost savings, especially for aerospace components made from costly titanium alloys. In this paper, the morphology, microstructure, chemical composition, and hardness of additive manufactured Ti-6Al-4V blocks are investigated and discussed. Blocks (7 beads wide, 7 layers high) were deposited using Ti-6Al-4V wire and a Nd:YAG laser. Two different sets of parameters are used and three different post heat treatment conditions (as-built, 600 °C/4 h, 1200 °C/2 h) are investigated. The experiments reveal elementary properties of additive manufactured Ti-6Al-4V material in correlation to process parameters and heat treatments, which are discussed comprehensively.

Al-matrix composite materials reinforced by Al-Cu-Fe particles

International Nuclear Information System (INIS)

Bonneville, J; Laplanche, G; Joulain, A; Gauthier-Brunet, V; Dubois, S

2010-01-01

Al-matrix material composites were produced using hot isostatic pressing technique, starting with pure Al and icosahedral (i) Al-Cu-Fe powders. Depending on the processing temperature, the final reinforcement particles are either still of the initial i-phase or transformed into the tetragonal ω-Al0 0.70 Cu 0.20 Fe 0.10 crystalline phase. Compression tests performed in the temperature range 293K - 823K on the two types of composite, i.e. Al/i and Al/ω, indicate that the flow stress of both composites is strongly temperature dependent and exhibit distinct regimes with increasing temperature. Differences exist between the two composites, in particular in yield stress values. In the low temperature regime (T ≤ 570K), the yield stress of the Al/ω composite is nearly 75% higher than that of the Al/i composite, while for T > 570K both composites exhibit similar yield stress values. The results are interpreted in terms of load transfer contribution between the matrix and the reinforcement particles and elementary dislocation mechanisms in the Al matrix.

Piezo-tunnel effect in Al/Al2O3/Al junctions elaborated by atomic layer deposition

Science.gov (United States)

Rafael, R.; Puyoo, E.; Malhaire, C.

2017-11-01

In this work, the electrical transport in Al/Al2O3/Al junctions under mechanical stress is investigated in the perspective to use them as strain sensors. The metal/insulator/metal junctions are elaborated with a low temperature process (≤200 °C) fully compatible with CMOS back-end-of-line. The conduction mechanism in the structure is found to be Fowler-Nordheim tunneling, and efforts are made to extract the relevant physical parameters. Gauge factors up to -32.5 were found in the fabricated devices under tensile stress. Finally, theoretical mechanical considerations give strong evidence that strain sensitivity in Al/Al2O3/Al structures originates not only from geometrical deformations but also from the variation of interface barrier height and/or effective electronic mass in the tunneling oxide layer.

Generation and evolution of nanoscale AlP and Al{sub 13}Fe{sub 4} particles in Al-Fe-P system

Energy Technology Data Exchange (ETDEWEB)

Qiao, Huan; Gao, Tong; Zhu, Xiangzhen; Wu, Yuying; Qian, Zhao; Liu, Xiangfa, E-mail: xfliu@sdu.edu.cn

2015-02-15

Highlights: • Diffusion and gradual solid reactions between Al and Fe{sub x}P phases in Al-Fe-P alloy were investigated. • Nanoscale AlP clusters are in-situ generated and evolve during the whole process. • This novel Al-Fe-P alloy has an excellent low-temperature refining performance on hypereutectic Al-Si alloy. - Abstract: In this paper, the gradual solid reactions between Al and Fe{sub x}P phases in Al-Fe-P alloy were investigated. The results show that the whole reaction process undergoes four main stages: the diffusion of Al atom, the generation of (Al, Fe, P) intermediate compound, the precipitation of nano AlP and Al{sub 13}Fe{sub 4} clusters and their growth to submicron particles. The microstructure of Fe-P particles evolves from the “egg-type”, the “sponge-type” to the “sesame-cake” structure. AlP and Al{sub 13}Fe{sub 4} nano phases have in-situ generated and evolved during the whole process. The gradual reaction mechanism has been discussed. Furthermore, a novel Al-Fe-P alloy which contains (Al, Fe, P) intermediate compounds and nano AlP particles has been synthesized and its low-temperature refining performance on A390 alloy has also been investigated.

Rebuilding the eastern Baltic cod stock under environmental change (part II): taking into account the costs of a marine protected area

NARCIS (Netherlands)

Roeckmann, C.; Tol, R.S.J.; Schneider, U.A.; St.John, M.A.

2009-01-01

This study adds a cost analysis of the Eastern Baltic cod fishery to the existing model presented in Röckmann et al. [2007a]. As cost data on this international fishery do not exist, data from Denmark are extrapolated to the whole international fishery. Additionally, unit and total variable costs

Japanese version of the ALS-FTD-Questionnaire (ALS-FTD-Q-J).

Science.gov (United States)

Watanabe, Yasuhiro; Beeldman, Emma; Raaphorst, Joost; Izumi, Yuishin; Yoshino, Hiide; Masuda, Michihito; Atsuta, Naoki; Ito, Satoru; Adachi, Tadashi; Adachi, Yoshiki; Yokota, Osamu; Oda, Masaya; Hanashima, Ritsuko; Ogino, Mieko; Ichikawa, Hiroo; Hasegawa, Kazuko; Kimura, Hideki; Shimizu, Toshio; Aiba, Ikuko; Yabe, Hayato; Kanba, Makoto; Kusumi, Kimiyoshi; Aoki, Tetsuya; Hiroe, Yu; Watanabe, Hirohisa; Nishiyama, Kazutoshi; Nomoto, Masahiro; Sobue, Gen; Nakashima, Kenji

2016-08-15

Amyotrophic lateral sclerosis (ALS) and frontotemporal dementia (FTD) share common clinical, genetic and neuropathological features. Some ALS patients have behavioral/personality changes, which could result in significant obstacles in the care provided by family members and caregivers. An easy screening tool would contribute greatly to the evaluation of these symptoms. We translated the ALS-FTD-Questionnaire, developed in the Netherlands, into Japanese (ALS-FTD-Q-J) and examined the clinimetric properties (internal consistency, construct and clinical validity). Patients with ALS and/or behavioral variant FTD (bvFTD) were evaluated alongside healthy controls in this multicenter study. All ALS patients, regardless of bvFTD status, were further evaluated by the frontal behavioral inventory (FBI) and for frontal/executive function, cognition, anxiety/depression, and motor functions. Data from 146 subjects were analyzed: ALS (92), ALS-bvFTD (6), bvFTD (16), and healthy controls (32). The internal consistency of the ALS-FTD-Q-J was good (Cronbach α=0.92). The ALS-FTD-Q-J showed construct validity as it exhibited a high correlation with the FBI (r=0.79). However, correlations were moderate with anxiety/depression and low with cognitive scales, in contrast to the original report, i.e. a moderate correlation with cognition and a low correlation with anxiety/depression. The ALS-FTD-Q-J discriminated ALS patients from (ALS-)bvFTD patients and controls. Thus, the ALS-FTD-Q-J is useful for evaluating Japanese ALS/FTD patients. Copyright © 2016 Elsevier B.V. All rights reserved.

Radiation detection with Nb/Al-AlOx/Al/Nb superconducting tunnel junctions

International Nuclear Information System (INIS)

Matsumura, Atsuki; Takahashi, Toru; Kurakado, Masahiko

1992-01-01

Superconductor radiation detectors have the possibility of 20-30 times better energy resolution than that of a high resolution Si detector. We fabricated Nb/Al-AlOx/Al/Nb superconducting tunnel junctions with low leakage current. X rays were detected with large area junctions of 178x178 μm 2 . High energy resolution of 160 eV for 5.9 keV was obtained. We also fabricated series connected junctions which covers a rather large area of 4x4 mm 2 . α particles injected into the rear substrate were detected using nonthermal phonons induced by the radiations in the substrate. (author)

ALS-Plus Syndrome: Non-Pyramidal Features in a Large ALS Cohort

Science.gov (United States)

McCluskey, Leo; Vandriel, Shannon; Elman, Lauren; Van Deerlin, Vivianna M.; Powers, John; Boller, Ashley; Wood, Elisabeth McCarty; Woo, John; McMillan, Corey T.; Rascovsky, Katya; Grossman, Murray

2014-01-01

Objective Autopsy studies show widespread pathology in amyotrophic lateral sclerosis (ALS), but clinical surveys of multisystem disease in ALS are rare. We investigated ALS-Plus syndrome, an understudied group of patients with clinical features extending beyond pyramidal and neuromuscular systems with or without cognitive/behavioral deficits. Methods In a large, consecutively-ascertained cohort of 550 patients with ALS, we documented atypical clinical manifestations. Genetic screening for C9orf72 hexanucleotide expansions was performed in 343 patients, and SOD1, TARDBP, and VCP were tested in the subgroup of patients with a family history of ALS. Gray matter and white matter imaging was available in a subgroup of 30 patients. Results Seventy-five (13.6%) patients were identified with ALS-Plus syndrome. We found disorders of ocular motility, cerebellar, extrapyramidal and autonomic functioning. Relative to those without ALS-Plus, cognitive impairment (8.0% vs 2.9%, p=0.029), bulbar-onset (49.3% vs 23.2%, pALS-Plus. Survival was significantly shorter in ALS-Plus (29.66 months vs 42.50 months, p=0.02), regardless of bulbar-onset or mutation status. Imaging revealed significantly greater cerebellar and cerebral disease in ALS-Plus compared to those without ALS-Plus. Conclusions ALS-Plus syndrome is not uncommon, and the presence of these atypical features is consistent with neuropathological observations that ALS is a multisystem disorder. ALS-Plus syndrome is associated with increased risk for poor survival and the presence of a pathogenic mutation. PMID:25086858

Tailoring ultrafine grained and dispersion-strengthened Ti 2 AlC/TiAl ...

Indian Academy of Sciences (India)

In situ Ti 2 AlC/TiAl composite was fabricated by hot-pressing method via the reaction system of Ti 3 AlC 2 and Ti-Al pre-alloyed powders at low temperature of 1150 ∘ C. The composite mainly consisted of TiAl, Ti 3 Al and Ti 2 AlC phases. Fine Ti 2 AlC particles were homogeneously distributed and dispersed in the matrix.

Solvothermal synthesis of Li–Al layered double hydroxides and their electrochemical performance

International Nuclear Information System (INIS)

Wei, Jinbo; Gao, Zan; Song, Yanchao; Yang, Wanlu; Wang, Jun; Li, Zhanshuang; Mann, Tom; Zhang, Milin; Liu, Lianhe

2013-01-01

In this paper, for the first time, Li/Al layered double hydroxides (LDHs) were synthesized by a facile and environment-friendly solvothermal approach. X-ray diffraction patterns show that the as-prepared products belong to the hexagonal phase. Well-defined LDHs particles with spiral-shape (1–2 μm), hexagonal (2–3 μm) and petal-like structures (10–15 μm) have been successfully fabricated by adjusting the content of water/ethanol in the synthesis process. A possible growth mechanism was proposed for the formation of these structures. Their electrochemical performances were investigated by cyclic voltammetry, galvanostatic charge/discharge test and electrochemical impedance spectroscopy. The hexagonal Li/Al LDHs calcined at 450 °C exhibit the specific capacitance of 848 F g −1 at a current density of 1.25 A g −1 . The high specific capacitance and remarkable rate capacity of Li/Al LDHs are promising for applications in capacitors and low-cost aqueous lithium ion batteries. - Graphical abstract: Hexagonal Li/Al layered double hydroxides (LDHs) with high specific surface area and remarkable rate capacity via a facile and environmentally friendly solvothermal approach. Highlights: ► Li/Al LDHs with different morphologies were fabricated by a solvothermal method. ► Hexagonal Li/Al LDHs display better electrochemical performance. ► A possible growth mechanism to explain the different morphology is proposed

Assessing behavioural changes in ALS: cross-validation of ALS-specific measures.

Science.gov (United States)

Pinto-Grau, Marta; Costello, Emmet; O'Connor, Sarah; Elamin, Marwa; Burke, Tom; Heverin, Mark; Pender, Niall; Hardiman, Orla

2017-07-01

The Beaumont Behavioural Inventory (BBI) is a behavioural proxy report for the assessment of behavioural changes in ALS. This tool has been validated against the FrSBe, a non-ALS-specific behavioural assessment, and further comparison of the BBI against a disease-specific tool was considered. This study cross-validates the BBI against the ALS-FTD-Q. Sixty ALS patients, 8% also meeting criteria for FTD, were recruited. All patients were evaluated using the BBI and the ALS-FTD-Q, completed by a carer. Correlational analysis was performed to assess construct validity. Precision, sensitivity, specificity, and overall accuracy of the BBI when compared to the ALS-FTD-Q, were obtained. The mean score of the whole sample on the BBI was 11.45 ± 13.06. ALS-FTD patients scored significantly higher than non-demented ALS patients (31.6 ± 14.64, 9.62 ± 11.38; p ALS-FTD-Q was observed (r = 0.807, p ALS-FTD-Q. Good construct validity has been further confirmed when the BBI is compared to an ALS-specific tool. Furthermore, the BBI is a more comprehensive behavioural assessment for ALS, as it measures the whole behavioural spectrum in this condition.

Sequential effects in deduction: Cost of inference switch

Directory of Open Access Journals (Sweden)

Antonio González-Hernández

2010-01-01

Full Text Available El paradigma de cambio de tarea ha ayudado a los psicólogos a conocer los procesos involucrados en el cambio de una actividad a otra. La literatura aporta resultados consistentes sobre la reconfiguración necesaria para el cambio de tarea (desaparición abrupta del coste cuando el cambio es predecible vs. reducción gradual del coste en condiciones de cambio impredecible; componentes endógeno y exógeno del coste; asimetría del coste.... En la investigación que presentamos aquí mostramos los resultados de varios experimentos en los que estudiamos el proceso de reconfiguración que se produce al alternar entre Modus Ponens y Modus Tollens. Los resultados muestran que el cambio de una inferencia a otra produce un empeoramiento en el número de errores de los participantes, así como un aumento en los tiempos de reacción (coste por interferencia del cambio. Además, encontramos una mejora gradual en el Modus Tollens en secuencias no predecibles y con intervalos respuesta-estímulo largos, en los ensayos de repetición de tarea. Ambos resultados son compatibles con la hipótesis de la reconfiguración de tarea.

La fenomenología existencial de M. Merleau-Ponty y la sociología

OpenAIRE

López Sáenz, Mª Carmen

1996-01-01

El artículo expone la visión de Merleau-Ponty sobre la sociedad, clarificando los fundamentos intersubjetivos de la misma, así como la influencia de este filósofo en la sociología contemporánea al tratar temas de recurrente actualidad como las relaciones yo-otros y sus consecuencias (empatía, amor, etc.) The article present Merleau-Ponty vision of society and the intersubjectivity foundation of modern societies. It also deals with the influence of this philosopher in contemporary sociology...

Distopias de la vida cotidiana

OpenAIRE

Di Biase, Carla Lujan

2014-01-01

Me interesa en el presente artículo explayarme un poco acerca de la burocracia del sistema de justicia tal cual se describe en algunos textos literarios con perspectiva de género y en un discurso no ficcional. Específicamente trataré con textos cortos en los que la burocracia aparece como un cierto tono kafkiano con el que lidian personajes femeninos. Considero al tema de la burocracia y la justicia como disparador de “momentos distópicos” insertos en nuestra realidad cotidiana, acentuados...

Editorial

Directory of Open Access Journals (Sweden)

Oscar Oswaldo Rodriguez Díaz

2014-12-01

Full Text Available El mercado de alta tecnología está creciendo a pasos gigantescos, es importante explorarlo, conocerlo y tratar de aprovechar al máximo, es así como la sociedad de consumo compra en forma masiva productos que apenas aprendemos a usar en un bajo porcenytaje de capacidades, un ejemplo es el celular, dispositivo que en primera instancia fue creado para realizar llamadas de cualquier puto y lugar "realizar llamadas", pero el mercado de consumo necesita nuevos dispositivos que complementen la vida diaria.

Importancia del articulador semiajustable en la rehabilitación

OpenAIRE

María Elena Gutiérrez Hernández; Ileana Grau León; Gema Lauzardo García del Prado

2003-01-01

Se realiza un estudio sobre la importancia del articulador semiajustable en la rehabilitación protésica. Se define la oclusión dentaria como la relación que se establece entre las arcadas dentarias cuando estas toman contacto entre sí permaneciendo el arco inferior inmóvil con respecto al superior. Debido a que es fundamental en la rehabilitación protésica tratar de respetar la integridad funcional del paciente, nos proponemos como objetivo reestablecer los contactos en los deslizamientos dur...

Niña-mujer-objeto de arte: la sexualidad femenina en la pintura.

OpenAIRE

Sánchez Concha, Francisco José; García Torralbo, María Cruz

2011-01-01

Hasta los impresionistas, el desnudo femenino formaba parte de la historia que el artista quería contar en su obra. El Impresionismo rompió los moldes tanto en la paleta como en la forma de tratar el desnudo de una mujer. A partir de entonces, la sexualidad femenina expresada en los cuadros de desnudos ha ido alcanzando cotas inimaginables ni por el Arte ni por el espectador. Sensualidad, erotismo, pasión, se convierten en algunos pintores en la más descarnada sexualidad, al...

Desarrollo de un sistema de control de una impresora 3D

OpenAIRE

Guijarro Hernández, Julio

2015-01-01

En el presente proyecto se van a tratar distintos aspectos de la impresión tridimensional, realizando un recorrido por los distintos tipos de impresiones que existen actualmente en el mercado, al igual que de los distintos tipos de materiales de los que se disponen para la impresión. También se montará y explicará la experiencia del montaje de la impresora Velleman K8200, analizando sus componentes, comportamiento y softwares utilizados para la realización de modelos. Finalmente se llev...

Epitaxial growth and properties of AlGaN-based UV-LEDs on Si(111) substrates

Energy Technology Data Exchange (ETDEWEB)

Saengkaew, Phannee

2010-07-08

An increasing demand for bright and efficient ultraviolet light emitting diodes (UVLEDs) is generated by numerous applications such as biochemical sensors, purification and sterilization, and solid-state white lighting. Al{sub x}Ga{sub 1-x}N is a promising material to develop UVLEDs due to the direct wide-bandgap material for emission wavelengths in the UV range and the capability of n- and p-type doping. To develop UV-LEDs on Si substrates is very interesting for low-cost UV-light sources since the Si substrate is available at low cost, in large-diameter size enabling the integration with well-known Si electronics. This work presents the first crack-free AlGaN-based UV-LEDs on Si(111) substrates by MOVPE growth. This AlGaN-based UV-LED on Si(111) substrate consists of Al{sub 0.1}Ga{sub 0.9}N:Si layers on LT-AlN/HT-AlN SL buffer layers and an active layer of GaN/Al{sub 0.1}Ga{sub 0.9}N MQWs followed by Mg-doped (GaN/Al{sub 0.1}Ga{sub 0.9}N) superlattices and GaN:Mg cap layers. It yields a {proportional_to}350 nm UV electroluminescence at room temperature and a turn-on voltage in a range of 2.6-3.1 V by current-voltage (I-V) measurements. The novel LT-AlN/HT-AlN superlattice buffer layers efficiently improve the crystalline quality of Al{sub x}Ga{sub 1-x}N layers and compensate a thermal tensile strain in Al{sub x}Ga{sub 1-x}N layers after cooling as observed by in-situ curvature measurements. The dislocation density could be reduced from 8.4 x 10{sup 10} cm{sup -2} in the AlN-based SLs to 1.8 x 10{sup 10} cm{sup -2} in the Al{sub 0.1}Ga{sub 0.9}N layers as determined by cross-sectional transmission electron microscopy (TEM) measurements. Crack-free Al{sub x}Ga{sub 1-x}N layers grown on these LT-AlN/HT-AlN superlattices with 0.05{<=}x{<=} 0.65 are achieved on Si substrates with good crystalline, optical, and electrical properties. The best crystalline quality of Al{sub 0.1}Ga{sub 0.9}N is obtained with {omega}-FWHMs of the (0002) and (10-10) reflections of

Plastic deformation of Al13Fe4 particles in Al-Al13Fe4 by high-speed compression

International Nuclear Information System (INIS)

Yoneyama, N.; Mizoguchi, K.; Kumai, S.; Sato, A.; Kiritani, M.

2003-01-01

Spray-formed Al-Fe alloys having undergone high-speed deformation were examined under a high-voltage electron microscope. Two types of specimens were examined; one containing fine Al 13 Fe 4 particles, and the other containing large particles. In the former specimen, deformation is found to proceed in three patterns, depending on specimen thickness and strain rate: (1) without deformation of the Al 13 Fe 4 ; (2) breaking of the Al 13 Fe 4 ; or (3) melting of the Al 13 Fe 4 . Local melting is found to alter some of the Al 13 Fe 4 particles, to impart five-fold symmetry in diffraction or an amorphous structure. In the latter specimen, introduction of glide dislocations enabled us to determine a shear system in the mc102 monoclinic c2/m crystal of Al 13 Fe 4 . On the bases of these observations, the mechanism of high-speed deformation is discussed while taking into account the highly stressed and/or heated states of Al 13 Fe 4 embedded in Al matrix

Synthesis and characterization of pillared bentonite with Al, AL/Fe and impregnated with Pd; Sintese e caracterizacao de bentonitas pilarizadas com Al, AL/Fe e impregnadas com Pd

Energy Technology Data Exchange (ETDEWEB)

Silva, Marcus Vinicius Costa; Pizarro, Alejandro Herrero; Molina, Carmen Belen, E-mail: marcus.ufpa@yahoo.com.br [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Instituto de Tecnologia. Faculdade de Engenharia Quimica; Seccion de Ingenieria Quimica, Facultad de Ciencias, Universidad Autonoma de Madri (Spain)

2017-10-01

In this work, a north american bentonite was pillared with Al and Al/Fe, creating the Al-PILC and Al-Fe-PILC, respectively. Then the Pd was impregnated in the materials, generating Pd-Al-PILC and Pd-Al-Fe-PILC, respectively. The samples were characterized by X-ray diffraction, differential thermal analysis and thermogravimetric and N{sub 2} adsorption at 77 K to determine the specific surface area by BET method (Brunauer - Emmett - Teller). There was an increase in the basal spacing of bentonite from 12.4Å in the original sample to 17.81Å in the Al-Fe-PILC, 17.20Å in Pd-Al-PILC and 17.05Å in the Pd-Al-Fe-PILC. The specific surface area increased from 19.05m{sup 2}/g in the original sample to 173.49m{sup 2}/g in Al-Fe-PILC, 101.31m{sup 2}/g to Pd-Al-PILC and 92m{sup 2}/g in Pd-Al-Fe-PILC. The pillaring process was successful and the synthesized materials have great potential for use as catalysts. (author)

Wear study of Al-SiC metal matrix composites processed through microwave energy

Science.gov (United States)

Honnaiah, C.; Srinath, M. S.; Prasad, S. L. Ajit

2018-04-01

Particulate reinforced metal matrix composites are finding wider acceptance in many industrial applications due to their isotropic properties and ease of manufacture. Uniform distribution of reinforcement particulates and good bonding between matrix and reinforcement phases are essential features in order to obtain metal matrix composites with improved properties. Conventional powder metallurgy technique can successfully overcome the limitation of stir casting techniques, but it is time consuming and not cost effective. Use of microwave technology for processing particulate reinforced metal matrix composites through powder metallurgy technique is being increasingly explored in recent times because of its cost effectiveness and speed of processing. The present work is an attempt to process Al-SiC metal matrix composites using microwaves irradiated at 2.45 GHz frequency and 900 W power for 10 minutes. Further, dry sliding wear studies were conducted at different loads at constant velocity of 2 m/s for various sliding distances using pin-on-disc equipment. Analysis of the obtained results show that the microwave processed Al-SiC composite material shows around 34 % of resistance to wear than the aluminium alloy.

Electrodeposition of Al from a 1-butylpyrrolidine-AlCl3 ionic liquid

Directory of Open Access Journals (Sweden)

Giridhar Pulletikurthi

2015-12-01

Full Text Available The addition of 1-butylpyrrolidine to AlCl3 results in the formation of an electrolyte that is suited to Al deposition. The feasibility of electrodepositing Al from the synthesized electrolyte was investigated. Several compositions of AlCl3 and 1-butylpyrrolidine were prepared for this purpose. These mixtures show a different phase behavior at various compositions of AlCl3 and 1-butylpyrrolidine. IR, Raman and NMR spectroscopy were employed to characterize the synthesized liquids. Among the prepared compositions, 1:1.2 mol ratio of 1-butylpyrrolidine:AlCl3 and the upper phase of 1:1.3 mol ratio of 1-butylpyrrolidine:AlCl3 were found to be suitable for Al electrodeposition at room temperature (RT. Uniform and thick (~µm thick layers of Al were obtained on copper at RT. Al deposition occured from the cationic species of AlCl3−xLy+ (where x≤2, y=1–2, and L=1-butylpyrrolidine in this electrolyte. This behavior is contrary to the well investigated classic AlCl3 based ionic liquids, where the deposition of Al occurs mainly from anionic Al2Cl7− ions.

Orientation of Al3Ti platelets in Al-Al3Ti functionally graded material manufactured by centrifugal method

International Nuclear Information System (INIS)

Watanabe, Y.; Fukui, Y.

1997-01-01

Al-Al 3 Ti functionally graded materials (FGMs) were manufactured by the centrifugal method with a commercial ingot of Al-5 mass% Ti master alloy. The alloy was melted at a liquid/solid coexisting temperature, at which Al 3 Ti remains as a solid, and then it was cast into a thick-walled ring. It was found that the Al-Al 3 Ti functionally graded material can be successfully fabricated by the centrifugal method. It was also found that the volume fraction of the Al 3 Ti can be increased by repetition of the centrifugal method. Since the shape of Al 3 Ti particles in a commercial alloy ingot is that of a platelet, the Al 3 Ti particles are arranged with their platelet planes nearly perpendicular to the radial direction. The orientation effects become stronger when the G number becomes larger. Although the final centrifugal casting was conducted under a very large centrifugal force for the specimen cast three times, the orientation effects were weaker than those in the specimen cast one time. From these observations, it is concluded that the origin of orientation of Al 3 Ti platelets can be attributed to the angular velocity gradient of the melt along the radial direction produced by the difference in the viscosity. (orig.)

In situ synthesis of Ti{sub 2}AlC–Al{sub 2}O{sub 3}/TiAl composite by vacuum sintering mechanically alloyed TiAl powder coated with CNTs

Energy Technology Data Exchange (ETDEWEB)

Wang, Jian [Department of Materials Science and Engineering of Tianjin University, Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China); Zhao, Naiqin, E-mail: nqzhao@tju.edu.cn [State Key Laboratory of Hydraulic Engineering Simulation and Safety, Tianjin (China); Department of Materials Science and Engineering of Tianjin University, Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China); Nash, Philip [Thermal Processing Technology Center, Illinois Institute of Technology, IL (United States); Liu, Enzuo; He, Chunnian; Shi, Chunsheng; Li, Jiajun [Department of Materials Science and Engineering of Tianjin University, Tianjin Key Laboratory of Composite and Functional Materials, Tianjin 300072 (China)

2013-11-25

Highlights: •Using zwitterionic surfactant to enhance the dispersion of the CNTs on the powder surface. •CNTs as carbon source decreased the formation temperature of Ti{sub 2}AlC. •Al{sub 2}O{sub 3} was generated in situ from the oxygen atoms introduced in the drying procedure. •Nanosized Ti{sub 3}Al was precipitated at 1250 °C and distribute in the TiAl matrix homogeneously. •Ti{sub 2}AlC–Al{sub 2}O{sub 3}/TiAl composite was synthesized in situ by sintering pre-alloy Ti–Al coated with CNTs. -- Abstract: Bulk Ti{sub 2}AlC–Al{sub 2}O{sub 3}/TiAl composites were in situ synthesized by vacuum sintering mechanically alloyed Ti–50 at.% Al powders coated with carbon nanotubes (CNTs). The pre-alloyed Ti–50 at.% Al powder was obtained by ball milling Ti and Al powders. The multi-walled carbon nanotubes as the carbon resource were covered on the surface of the pre-alloyed powders by immersing them into a water solution containing the CNTs. A zwitterionic surfactant was used to enhance the dispersion of the CNTs on the powder surface. The samples were cold pressed and sintered in vacuum at temperatures from 950 to 1250 °C, respectively. The results show that the reaction of forming Ti{sub 2}AlC can be achieved below 950 °C, which is 150 °C lower than in the Ti–Al–TiC system and 250 °C lower than for the Ti–Al–C system due to the addition of CNTs. Additionally, the reinforcement of Al{sub 2}O{sub 3} particles was introduced in situ in Ti{sub 2}AlC/TiAl by the drying process and subsequent sintering of the composite powders. Dense Ti{sub 2}AlC–Al{sub 2}O{sub 3}/TiAl composites were obtained by sintering at 1250 °C and exhibited a homogeneous distribution of Ti{sub 2}AlC, Al{sub 2}O{sub 3} and precipitated Ti{sub 3}Al particles and a resulting high hardness.

27Al NMR studies of NpPd5Al2

International Nuclear Information System (INIS)

Chudo, H.; Sakai, H.; Tokunaga, Y.; Kambe, S.; Aoki, D.; Homma, Y.; Shiokawa, Y.; Haga, Y.; Ikeda, S.; Matsuda, T.D.; Onuki, Y.; Yasuoka, H.

2009-01-01

We present 27 Al NMR studies for a single crystal of the Np-based superconductor NpPd 5 Al 2 (T c =4.9K). We have observed a five-line 27 Al NMR spectrum with a center line and four satellite lines separated by first-order nuclear quadrupole splittings. The Knight shift clearly drops below T c . The temperature dependence of the 27 Al nuclear spin-lattice relaxation rate shows no coherence peak below T c , indicating that NpPd 5 Al 2 is an unconventional superconductor with an anisotropic gap. The analysis of the present NMR data provides evidence for strong-coupling d-wave superconductivity in NpPd 5 Al 2 .

Magnetic tunnel junctions with AlN and AlNxOy barriers

International Nuclear Information System (INIS)

Schwickert, M. M.; Childress, J. R.; Fontana, R. E.; Kellock, A. J.; Rice, P. M.; Ho, M. K.; Thompson, T. J.; Gurney, B. A.

2001-01-01

Nonoxide tunnel barriers such as AlN are of interest for magnetic tunnel junctions to avoid the oxidation of the magnetic electrodes. We have investigated the fabrication and properties of thin AlN-based barriers for use in low resistance magnetic tunnel junctions. Electronic, magnetic and structural data of tunnel valves of the form Ta (100 Aa)/PtMn (300 Aa)/CoFe 20 (20 Aa - 25 Aa)/barrier/CoFe 20 (10 - 20 Aa)/NiFe 16 (35 - 40 Aa)/Ta (100 Aa) are presented, where the barrier consists of AlN, AlN x O y or AlN/AlO x with total thicknesses between 8 and 15 Aa. The tunnel junctions were sputter deposited and then lithographically patterned down to 2 x 2μm 2 devices. AlN was deposited by reactive sputtering from an Al target with 20% - 35% N 2 in the Ar sputter gas at room temperature, resulting in stoichiometric growth of AlN x (x=0.50±0.05), as determined by RBS. TEM analysis shows that the as-deposited AlN barrier is crystalline. For AlN barriers and AlN followed by natural O 2 oxidation, we obtain tunnel magnetoresistance >10% with specific junction resistance R j down to 60Ωμm 2 . [copyright] 2001 American Institute of Physics

Transparent and flexible heaters based on Al:ZnO degenerate semiconductor

Science.gov (United States)

Roul, Monee K.; Obasogie, Brandon; Kogo, Gilbert; Skuza, J. R.; Mundle, R. M.; Pradhan, A. K.

2017-10-01

We report on high performance transparent Al:ZnO (AZO) thin film heaters on flexible polymer (polyethylene terephthalate) and glass substrates which demonstrate low sheet resistivity. AZO thin films were grown by radio-frequency magnetron sputtering at low Ts (below 200 °C) on flexible, transparent polyethylene terephthalate substrates that show stable and reproducible results by applying low (pain/injury therapy smart windows, automobile window defrosters, and low-cost power electronics.

A study of the Al-rich part of the Al-Re alloy system

International Nuclear Information System (INIS)

Balanetskyy, S.; Grushko, B.

2008-01-01

The Al-rich part of the Al-Re phase diagram was reinvestigated by scanning and transmission electron microscopy, powder X-ray diffraction and differential thermal analysis. The earlier reported Al 12 Re, Al 6 Re, and Al 11 Re 4 phases were confirmed. Close to the Al 4 Re composition a high-temperature h-Al 4 Re and a low-temperature l-Al 4 Re phase were found to be formed at slightly different compositions. Both exhibited compositional ranges. A new phase was revealed close to the Al 3 Re composition. The Al 11 Re 4 phase is formed congruently at 1650 deg. C, Al 3 Re peritectically at 1610 deg. C, h-Al 4 Re peritectically at 1410 deg. C, l-Al 4 Re peritectically at ∼1000 deg. C, Al 6 Re peritectically at 813 deg. C and Al 12 Re peritectically at 746 deg. C. Finally, the Al 12 Re-(Al) eutectic is formed at 658 deg. C. The Al 3 Re and h-Al 4 Re are decomposed by eutectoid reactions at ∼946 and 833 deg., respectively. The structure of the h-Al 4 Re phase has not yet been clarified, but it is distinctly different from the Al 4 W phase suggested earlier. The structure of l-Al 4 Re was confirmed. The Al 3 Re phase was found to have a monoclinic structure with a = 0.5180(4) nm, b = 3.97641(9) nm, c = 0.4955(3) nm and β = 99.55(7) o

Artificial intelligent decision support for low-cost launch vehicle integrated mission operations

Science.gov (United States)

Szatkowski, Gerard P.; Schultz, Roger

1988-01-01

The feasibility, benefits, and risks associated with Artificial Intelligence (AI) Expert Systems applied to low cost space expendable launch vehicle systems are reviewed. This study is in support of the joint USAF/NASA effort to define the next generation of a heavy-lift Advanced Launch System (ALS) which will provide economical and routine access to space. The significant technical goals of the ALS program include: a 10 fold reduction in cost per pound to orbit, launch processing in under 3 weeks, and higher reliability and safety standards than current expendables. Knowledge-based system techniques are being explored for the purpose of automating decision support processes in onboard and ground systems for pre-launch checkout and in-flight operations. Issues such as: satisfying real-time requirements, providing safety validation, hardware and Data Base Management System (DBMS) interfacing, system synergistic effects, human interfaces, and ease of maintainability, have an effect on the viability of expert systems as a useful tool.

A PRECISE, LOW-COST RTK GNSS SYSTEM FOR UAV APPLICATIONS

Directory of Open Access Journals (Sweden)

W. Stempfhuber

2012-09-01

Full Text Available High accuracy with real-time positioning of moving objects has been considered a standard task of engineering geodesy for 10 to 15 years. An absolute positioning accuracy of 1–3 cm is generally possible worldwide and is further used in many areas of machine guidance (machine control and guidance, and farming (precision farming as well as for various special applications (e.g. railway trolley, mining, etc.. The cost of the measuring instruments required for the use of geodetic L1/L2 receivers with a local reference station amounts to approximately USD 30,000 to 50,000. Therefore, dual frequency RTK GNSS receivers are not used in the mass market. Affordable GPS/GNSS modules have already reached the mass market in various areas such as mobile phones, car navigation, the leisure industry, etc. Kinematic real-time positioning applications with centimetre or decimetre levels could also evolve into a mass product. In order for this to happen, the costs for such systems must lie between USD 1,000 to 2,000. What exactly low-cost means is determined by the precise specifications of the given individual application. Several university studies in geodesy focus on the approach of high-accuracy positioning by means of single frequency receivers for static applications [e.g. GLABSCH et. al. 2009, SCHWIEGER and GLÄSER 2005, ALKAN 2010, REALINI et. al. 2010, KORTH and HOFMANN 2011]. Although intelligent approaches have been developed that compute a trajectory in the post-processing mode [REALINI et. al., 2010], at present, there are only a very few GNSS Low-Cost Systems that enable real-time processing. This approach to precise position determination by means of the computation of static raw data with single frequency receivers is currently being explored in a research project at the Beuth Hochschule für Technik Berlin – and is being further developed for kinematic applications. The project is embedded in the European Social Fund. It is a follow-up project

Abu al-Layth al-Libi

Science.gov (United States)

2015-02-01

success. As an Arab participant acknowledged very early on, “the situation was really harsh. All the brothers were tired,” as they lacked food and... glorious battles that occurred during the early Islamic period.133 He stressed the importance of the battlefield as the path to achieve honor and dignity...diaspora in Waziristan. In the words of Walid Othmani, a French jihadi trained by al-Qa`ida in Waziristan in 2008, “[Al-Libi] was someone well-known and

Cyclic Oxidation Behavior of CuCrAl Cold-Sprayed Coatings for Reusable Launch Vehicles

Science.gov (United States)

Raj, Sai; Karthikeyan, J.

2009-01-01

The next generation of reusable launch vehicles is likely to use GRCop-84 [Cu-8(at.%)Cr-4%Nb] copper alloy combustion liners. The application of protective coatings on GRCop-84 liners can minimize or eliminate many of the environmental problems experienced by uncoated liners and significantly extend their operational lives and lower operational cost. A newly developed Cu- 23 (wt.%) Cr-5% Al (CuCrAl) coating, shown to resist hydrogen attack and oxidation in an as-cast form, is currently being considered as a protective coating for GRCop-84. The coating was deposited on GRCop-84 substrates by the cold spray deposition technique, where the CuCrAl was procured as gas-atomized powders. Cyclic oxidation tests were conducted between 773 and 1,073 K to characterize the coated substrates.

SAP-like ultrafine-grained Al composites dispersion strengthened with nanometric AlN

International Nuclear Information System (INIS)

Balog, M.; Krizik, P.; Yan, M.; Simancik, F.; Schaffer, G.B.; Qian, M.

2013-01-01

This paper reports the development of novel Sinter-Aluminum-Pulver (SAP)-like Al–AlN nanocomposites via replacing the native Al 2 O 3 thin films on fine Al powder with a large volume fraction of in situ formed nanometric AlN dispersoids. Fine gas-atomized Al powder (d 50 =1.3 µm) compacts were first partially nitrided at 590 °C in flowing nitrogen, controlled by a small addition of Sn (0.3–0.4 wt%), and subsequently consolidated by hot direct extrusion. The resulting Al–AlN composites consisted of submicrometric Al grains reinforced with nanometric AlN dispersoids together with some nanometric Al 2 O 3 dispersoids. An Al–13 vol% AlN nanocomposite fabricated this way achieved exceptional ultimate tensile strength of 227 MPa, yield strength of 195 MPa and Young's modulus of 66 GPa at 300 °C, superior to typical SAP materials and coarse grained Al–AlN composites. In addition, the Al–13 vol% AlN nanocomposite exhibited good thermal stability up to 500 °C. The strengthening mechanism is discussed

Don Quijote, doña Rodríguez y los duques

Directory of Open Access Journals (Sweden)

Stanislav Zimic

1997-12-01

Full Text Available Al llegar Don Quijote al palacio de los duques y "viéndose tratar del mesmo modo que él había leído se trataban Ios tales caballeros en Ios pasados siglos ... , aquél fue el primer día que de todo en todo conoció y creyó ser caballero andante verdadero y no fantastíco" (1378. Comprensiblemente, esta afirmacion ha causado gran perplejidad entre los lectores de todas las épocas: "Luego, antes ¿no lo había creído?" . La cuestión se complica mucho más, poco después de estos eufóricos momentos, al confesar Don Quijote a la duquesa: "Dios sabe si hay Dulcinea o no en el mundo, o si es fantástica ono es fantástica ...

Analisis Kecenderungan Manhaj Akidah Shaykh Shams al-Din al-Sumatera’i

Directory of Open Access Journals (Sweden)

MOHD HAIDHAR KAMARZAMAN

2016-12-01

Full Text Available Shaykh Shams al-Din al-Sumatera'i is a very great and respected scholar during 16th and 17th century of Acheh. His knowledge in various fields recognized by local and international scholars. He had been a Qadi Malik al-’Adil, a religious leader, who became a referred by communities and country during the reign of the three Sultans of Aceh. He has authored nearly 40 pieces of books related to the theology and sufism. This study focuses on the methods used by Shaykh Shams al-Din al-Sumatera'i in his theological writings. This study found that Shaykh Shams al-Din al-Sumatera'i had used six methods in the such writings.

Costs, quality of life and cost-effectiveness of arthroscopic and open repair for rotator cuff tears: an economic evaluation alongside the UKUFF trial.

Science.gov (United States)

Murphy, J; Gray, A; Cooper, C; Cooper, D; Ramsay, C; Carr, A

2016-12-01

A trial-based comparison of the use of resources, costs and quality of life outcomes of arthroscopic and open surgical management for rotator cuff tears in the United Kingdom NHS was performed using data from the United Kingdom Rotator Cuff Study (UKUFF) randomised controlled trial. Using data from 273 patients, healthcare-related use of resources, costs and quality-adjusted life years (QALYs) were estimated at 12 months and 24 months after surgery on an intention-to-treat basis with adjustment for covariates. Uncertainty about the incremental cost-effectiveness ratio for arthroscopic versus open management at 24 months of follow-up was incorporated using bootstrapping. Multiple imputation methods were used to deal with missing data. There were no significant differences between the arthroscopic and open groups in terms of total mean use and cost of resources or QALYs at any time post-operatively. Open management dominated arthroscopic management in 59.8% of bootstrapped cost and effect differences. The probability that arthroscopic management was cost-effective compared with open management at a willingness-to-pay threshold of £20 000 per QALY gained was 20.9%. There was no significant overall difference in the use or cost of resources or quality of life between arthroscopic and open management in the trial. There was uncertainty about which strategy was most cost-effective. Cite this article: Bone Joint J 2016;98-B:1648-55. ©2016 Gray et al.

Calotropis procera seedlings could be used as a rapid cost effective bioindicator for measuring aluminum environmental pollution

Science.gov (United States)

Mosa, Kareem A.; El-Keblawy, Ali; Najar, Atyat

2017-04-01

Calotropis procera seedlings could be used as a rapid cost effective bioindicator for measuring aluminum environmental pollution Kareem A. Mosa, Ali El-Keblawy, Atyat Najar Department of Applied Biology, College of Sciences, University of Sharjah, UAE Rapid industrialization and urbanization processes has led to the incorporation of different heavy metals in natural resources like soil, water and air thus affecting their quality. Aluminum (Al) is a dominant heavy metal pollutant that causes serious toxic effects to living systems including plants. Therefore, it is critical to regularly monitor the changes in Al levels in natural resources. Living organisms could be used as bioindicators for monitoring and measuring the levels of heavy metals in environmental samples. The aim of this study was to develop a cost effective bioindicator for monitoring aluminum (Al) and assess the damage caused by Al bioaccumulation using the root system of Calotropis Procera seedlings. A hydroponic system was developed for growing C. Procera in four different concentrations of Al (20, 40, 60 and 80 ppm). Root length and shoot fresh and dry weights were assessed after 5, 10, 15 and 20 days of Al treatment. The results showed remarkable sensitivity of C. Procera seedlings for the different concentrations of Al. There was gradual but significant decrease in C. Procera root length with the increase in the Al concentrations. X-ray fluorescence microscopy (XRF) analysis indicated a significant increase in Al concentration in C. Procera roots with the increase of both Al concentration in the hydroponic solution and the growing period. Moreover, electrical conductivity analysis showed that Al induced damage to C. Procera root plasma membrane as indicated by the increase in electrolyte leakages. Randomly amplified polymorphic DNA (RAPD) PCR analysis confirmed the genotoxin effect of Al which induced C. Procera genomic DNA modification. Altogether, the result demonstrated that C. Procera could

Microwave-assisted combustion synthesis of NiAl intermetallics in a single mode applicator: Modeling and optimisation

International Nuclear Information System (INIS)

Poli, G.; Sola, R.; Veronesi, P.

2006-01-01

The microwave-assisted combustion synthesis of NiAl intermetallics in a single mode applicator has been simulated numerically and performed with the aim of achieving the highest yields, energy efficiency and process reproducibility. The electromagnetic field modeling of the microwave system allowed to chose the proper experimental set-up and the materials more suitable for the application, minimising the reflected power and the risks of arcing. In all the experimental conditions tested, conversions of 3-5 g 1:1 atomic ratio Ni and Al powder compacts into NiAl ranged from 98.7% to 100%, requiring from 30 to 180 s with power from 500 to 1500 W. The optimisation procedure allowed to determine and quantify the effects of the main process variables on the ignition time, the NiAl yields and the specific energy consumption, leading to a fast, reproducible and cost-effective process of microwave-assisted combustion synthesis of NiAl intermetallics

Ultrasonic spot welding of Al/Mg/Al tri-layered clad sheets

International Nuclear Information System (INIS)

Macwan, A.; Patel, V.K.; Jiang, X.Q.; Li, C.; Bhole, S.D.; Chen, D.L.

2014-01-01

Highlights: • The optimal welding condition is achieved at 100 J and 0.1 s. • Failure load first increases and then decreases with increasing welding energy. • The highest failure load after welding is close to that of the clad sheets. • At low energy levels failure occurs in the mode of interfacial failure. • At high energy levels failure takes place at the edge of nugget region. - Abstract: Solid-state ultrasonic spot welding (USW) was used to join Al/Mg/Al tri-layered clad sheets, aiming at exploring weldability and identifying failure mode in relation to the welding energy. It was observed that the application of a low welding energy of 100 J was able to achieve the optimal welding condition during USW at a very short welding time of 0.1 s for the tri-layered clad sheets. The optimal lap shear failure load obtained was equivalent to that of the as-received Al/Mg/Al tri-layered clad sheets. With increasing welding energy, the lap shear failure load initially increased and then decreased after reaching a maximum value. At a welding energy of 25 J, failure occurred in the mode of interfacial failure along the center Al/Al weld interface due to insufficient bonding. At a welding energy of 50 J, 75 J and 100 J, failure was also characterized by the interfacial failure mode, but it occurred along the Al/Mg clad interface rather than the center Al/Al weld interface, suggesting stronger bonding of the Al/Al weld interface than that of the Al/Mg clad interface. The overall weld strength of the Al/Mg/Al tri-layered clad sheets was thus governed by the Al/Mg clad interface strength. At a welding energy of 125 J and 150 J, thinning of weld nugget and extensive deformation at the edge of welding tip caused failure at the edge of nugget region, leading to a lower lap shear failure load

KITAB AL-SANĪ AL-MAṬĀLIB: INTERKONEKSI NAHWU DAN TASAWUF

Directory of Open Access Journals (Sweden)

Zakiyah Zakiyah

2012-12-01

Tulisan ini mereview buku yang berjudul al-Sanī al-Maṭālib yang ditulis oleh Kiai Nur Iman Mlangi Yogyakarta. Buku ini ditulis dalam bahasa Arab yang me­ngandung interkoneksi antara ilmu Nahwu (tata bahasa Arab dengan mis­tisis­me. Buku ini sangat menarik karena kenyataan bahwa kedua pengetahuan tersebut memiliki aturan sendiri-sendiri. Selain itu, sangat sedikit penulis yang menulis dengan gaya seperti itu. Salah satunya adalah Syaikh Abdul Qadir bin Ahmad al-Kuhany dengan karyanya yang berjudul Manniyat al-Fāqir al-Munjarid wa Sayrat al-Murīd al-Mutafarrid. Buku al-Saniy al-Muthalib diduga telah ditulis pada akhir abad ke-18 atau awal abad ke-19, menurut periode kehidupan Kiai Nur Iman yaitu sekitar pertengahan abad ke-18. Aturan Nahwu dalam buku ini dijelaskan secara teosofi yang dimulai dengan penjelasan mengenai tauhid (keesaan Tuhan sebagai kajian dasar bagi orang Islam, yang diikuti dengan makna dari masing-masing aturan bahasa Arab dalam aspek mistiknya.

Stability of an amorphous alloy of the Mm-Al-Ni-Cu system

Directory of Open Access Journals (Sweden)

Carlos Triveño Rios

2012-10-01

Full Text Available An investigation was made of the stability of melt-spun ribbons of Mm55Al25Ni10Cu10 (Mm = Mischmetal amorphous alloy. The structural transformations that occurred during heating were studied using a combination of X-ray diffraction (XRD and differential scanning calorimetry (DSC. Crystallization took place through a multi-stage process. The first stage of transformation corresponded to the formation of a metastable phase followed by cfc-Al precipitation, while in the second stage, exothermic transformations led to the formation of complex and unidentified Mm(Cu, Ni and MmAl(Cu, Ni phases. The transformation curves recorded from isothermal treatments at 226 °C and 232 °C indicated that crystallization occurred through nucleation and growth, with diffusion-controlled growth occurring in the first crystallization stage. The supercooled liquid region, ∆Tx, at 40 K/min was ~80 K. This value was obtained by the substitution of Mm (=Ce + La + Nd + Pr for La or Ce, saving chemical element-related costs.

A study of low-cost, robust assistive listening system (ALS) based on digital wireless technology.

Science.gov (United States)

Israsena, P; Dubsok, P; Pan-Ngum, S

2008-11-01

We have developed a simple, low-cost digital wireless broadcasting system prototype, intended for a classroom of hearing impaired students. The system is designed to be a low-cost alternative to an existing FM system. The system implemented is for short-range communication, with a one-transmitter, multiple-receiver configuration, which is typical for these classrooms. The data is source-coded for voice-band quality, FSK modulated, and broadcasted via a 915 MHz radio frequency. A DES encryption can optionally be added for better information security. Test results show that the system operating range is approximately ten metres, and the sound quality is close to telephone quality as intended. We also discuss performance issues such as sound, power and size, as well as transmission protocols. The test results are the proof of concept that the prototype is a viable alternative to an existing FM system. Improvements can be made to the system's sound quality via techniques such as channel coding, which is also discussed.

The cost-effectiveness of supportive periodontal care for patients with chronic periodontitis.

Science.gov (United States)

Gaunt, Francesca; Devine, Maria; Pennington, Mark; Vernazza, Chris; Gwynnett, Erika; Steen, Nick; Heasman, Peter

2008-09-01

To systematically evaluate the evidence for effectiveness of supportive periodontal care (SPC) provided in specialist care and general practice for patients with chronic periodontitis; to construct a model for the cost effectiveness of SPC. Electronic database searches of MEDLINE, EMBASE and SCOPUS were performed with hand searching of relevant journals and Workshops of Periodontology. SPC for patients with chronic periodontitis, at least 12 months follow-up and clinical attachment level as a primary outcome. Three articles addressed the question (Nyman et al. 1975, Axelsson & Lindhe 1981, Cortellini et al. 1994): Deltas CAL for patients undergoing "specialist" SPC were 0.1 mm (2 years), 0.2 mm (6 years) and -0.01 mm (3 years) respectively. In generalist care the Deltas CAL during SPC were -2.2, -1.8 and -2.8 mm. Differences between specialist and generalist SPC were an extra 20.59 tooth years and 3.95 mm attachment loss for generalist SPC. Incremental cost-effectiveness ratios were an extra 288 euros for one tooth year or an extra 1503 euros/1 mm reduction in loss of attachment for SPC delivered in specialist care. SPC delivered in specialist as compared with general practice will result in greater stability of clinical attachment but this will be achieved at relatively greater cost.

Rekonstruksi Konsep Ijtihad: Studi Pemikiran Ben’umar tentang al-Ijtihad fi al-Waqi’

Directory of Open Access Journals (Sweden)

Duski Ibrahim

2015-10-01

Full Text Available This paper is the result of a research that evaluating the reconstruction the concept of ijtihad, by discuss the idea of al-Ijtihad Ben'umar fi al-waqi’. This paper concludes that Al-Ijtihad fi al-waqi’ is actually a form of collective ijtihad (al ijtihad al-jama'i, by gathering the experts of shari'ah law (fuqaha` ash-shar'i and experts Researchers and scientists (khubara` al-'ashr. Because experts know the nash purposes, while researchers and scientists (al-khubara` know the reality (al-waqi’, the effects in the future (ma'alat = future effect and challenges (tahaddiyat. The idea of formulating the concept of al-ijtihad fi al-waqi’ emerged based on a premise that ijtihad is a creation of experts to implement Islamic law in society. Therefore, the concept of ijtihad experienced a significant development, start from using the nash from the language aspects, continue to the using of logic. At the moment when the situation people are increasingly develop, then the creation of ijtihad become a necessary to developed, for example in the form of al-ijtihad fi al-waqi’ . About the source of the formation of the concept of al -ijtihad fi al-waqi’ comes from theory about the functions of nash, al-manath theory in Islamic law, and supported by the theory of al-mashlalah al-mursalah.

Morphology, microstructure, and hardness of titanium (Ti-6Al-4V) blocks deposited by wire-feed additive layer manufacturing (ALM)

Energy Technology Data Exchange (ETDEWEB)

Brandl, Erhard, E-mail: erhard.brandl@eads.net [EADS Innovation Works, Metallic Technologies and Surface Engineering, D-81663 Munich (Germany); Schoberth, Achim, E-mail: achim.schoberth@eads.net [EADS Innovation Works, Metallic Technologies and Surface Engineering, D-81663 Munich (Germany); Leyens, Christoph, E-mail: christoph.leyens@tu-dresden.de [Technical University of Dresden, Institute of Materials Science, Chair of Materials Technology, Berndt-Bau, Helmholtzstr. 7, D-01062 Dresden (Germany)

2012-01-15

Highlights: Black-Right-Pointing-Pointer The microstructure and hardness of deposited Ti-6Al-4V blocks are investigated. Black-Right-Pointing-Pointer Hardness is influenced by post heat treatment rather than by process parameters. Black-Right-Pointing-Pointer Microstructure within the prior {beta}-grains varies to some extent from grain to grain. Black-Right-Pointing-Pointer A 600 Degree-Sign C/4 h treatment significantly increased the average hardness. - Abstract: Additive layer manufacturing offers a potential for time and cost savings, especially for aerospace components made from costly titanium alloys. In this paper, the morphology, microstructure, chemical composition, and hardness of additive manufactured Ti-6Al-4V blocks are investigated and discussed. Blocks (7 beads wide, 7 layers high) were deposited using Ti-6Al-4V wire and a Nd:YAG laser. Two different sets of parameters are used and three different post heat treatment conditions (as-built, 600 Degree-Sign C/4 h, 1200 Degree-Sign C/2 h) are investigated. The experiments reveal elementary properties of additive manufactured Ti-6Al-4V material in correlation to process parameters and heat treatments, which are discussed comprehensively.

Analysis of Institutional Artifact Cost in Management Control in a Textile Company

Directory of Open Access Journals (Sweden)

Rodrigo Barraco Marassi

2014-08-01

Full Text Available The present study aimed to analyze the process of institutionalization of artifacts in cost management control of Paraná company in the textile sector. For this, we developed descriptive, qualitative research with development of a case study conducted by semi-structured interviews, questionnaires and document analysis. The company under study was selected for accessibility and intentionally to be in the implementation phase of change in management control practices. Was structured semi-structured interviews and questionnaires based on Burns and Scapens (2000, Guerreiro et al. (2005 and Rock and Warrior (2010. The controller and an employee of the comptroller, as well as two officials involved in the supply of the information system were interviewed. The company seeks to implement new accounting and management reporting system that offers the best timing and management of costs and fixed and variable costs, cost centers, among others. The research results show that the encoding step was performed by the controller and by consulting the codified principles and institutional desires in routines, rules and regulations and so draft the proposed changes. The company has not adequately met some factors of institutionalization listed by Guerreiro et al. (2005, regarding training of the people involved, elements of repetition and perceived consequences of the implementation of change by people. By analyzing the case study and reflect the results with the lens of institutional theory, it follows that to obtain management information artifacts cost depends on appropriate processes for data collection, and even when using updated technologies, needs some several facts that this process becomes institutionalized, which may be better understood based on this lens.

SANANDO AL SANADOR

Directory of Open Access Journals (Sweden)

Juan Pablo Acuña, Dr.

2017-09-01

Full Text Available RESUMEN: La dependencia o adicción a sustancias de uso profesional es un problema que puede afectar gravemente a médicos de diferentes especialidades. En la anestesiología hay mayor riesgo de dependencia a opioides e hipnóticos que en otras especialidades y puede llegar a afectar al 1% de los médicos anestesiólogos.La fisiopatología del trastorno por uso de sustancias tiene hechos comunes para diferentes drogas. Interactúan la vulnerabilidad genética y factores psicosociales como predisponentes y los efectos psicobiológicos de la sustancia como factor gatillante. En el caso de los anestesiólogos, la sustancia se encuentra en el lugar de trabajo y por lo tanto, el individuo está constantemente expuesto.Una disfunción previa del sistema de recompensa en el circuito mesocorticolímbico o causada por la exposición a la sustancia adictiva es la piedra central de la neurobiología de las adicciones. Los opioides, anfetaminas, canabinoides, alcohol y nicotina, son algunas de las sustancias exógenas que activan el circuito y causan inicialmente un efecto hedónico que reforzará la conducta por repetir la experiencia. Con el tiempo la interacción con la droga será para evitar los síntomas de abstinencia.Dada la exposición laboral de los anestesiólogos, es necesario prevenir, detectar y tratar precozmente a quienes están abusando de sustancias durante su ejercicio profesional.Por las características de estos fármacos, aspectos psicológicos especiales de los médicos y el contexto laboral se hace necesario un tratamiento especializado y en anestesiólogos la reinserción laboral debe ser un proceso controlado, gradual y con un seguimiento prolongado. SUMMARY: Prescription drugs dependence seriously impairs doctors from differents fields of medicine. Anesthesiology has greater risk than other specialties to opioids and hypnotics dependence, with prevalence up to 1%.Substances use disorder has common mechanisms of disease regardless

Study of the 26Al(n,p)26Mg and 26Al(n,α)23Na reactions using the 27Al(p,p')27Al inelastic scattering reaction

International Nuclear Information System (INIS)

Benamara, S; De Séréville, N; Hammache, F; Stefan, I; Roussel, P; Ancelin, S; Assié, M; Guillot, J; Le Crom, B; Lefebvre, L; Adsley, P; Laird, A M; Barton, C; Diget, C; Fox, S; Coc, A; Deloncle, I; Hamadache, C; Kiener, J; Lefebfre-Schuhl, A

2016-01-01

26 Al was the first cosmic radioactivity ever detected in the galaxy as well as one of the first extinct radioactivity observed in refractory phases of meteorites. Its nucleosynthesis in massive stars is still uncertain mainly due to the lack of nuclear information concerning the 26 Al(n,p) 26 Mg and 26 Al(n,α) 23 Na reactions. We report on a single and coincidence measurement of the 27 Al(p,p') 27 Al(p) 26 Mg and 27 Al(p,p') 27 Al(α) 23 Na reactions performed at the Orsay TANDEM facility aiming at the spectroscopy study of 27 Al above the neutron threshold. Fourteen states are observed for the first time within 350 keV above the 26 Al+n threshold. (paper)

AlN/Al dual protective coatings on NdFeB by DC magnetron sputtering

Energy Technology Data Exchange (ETDEWEB)

Li Jinlong; Mao Shoudong; Sun Kefei [Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Li Xiaomin [Shanghai Institute of Ceramics Chinese Academy of Sciences, Shanghai 200050 (China); Song Zhenlun [Zhejiang Province Key Laboratory of Magnetic Materials and Application Technology, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China)], E-mail: songzhenlun@nimte.ac.cn

2009-11-15

AlN/Al dual protective coatings were prepared on NdFeB by DC magnetron sputtering in a home-made industrial apparatus. Comparing with Al coating, AlN/Al coatings have a denser structure of an outmost AlN amorphous layer following an inner Al columnar crystal layer. The coatings and NdFeB substrate combine well, and moreover, there is occurrence of metallurgy bonding in the interface layer. Both Al and AlN/Al coatings have a good protective ability to NdFeB. Especially, the corrosion resistance of AlN/Al coated NdFeB is improved largely. AlN/Al and Al protective coatings not only do not deteriorate the magnetic properties of NdFeB, but contribute to their slight increase.

AlN/Al dual protective coatings on NdFeB by DC magnetron sputtering

International Nuclear Information System (INIS)

Li Jinlong; Mao Shoudong; Sun Kefei; Li Xiaomin; Song Zhenlun

2009-01-01

AlN/Al dual protective coatings were prepared on NdFeB by DC magnetron sputtering in a home-made industrial apparatus. Comparing with Al coating, AlN/Al coatings have a denser structure of an outmost AlN amorphous layer following an inner Al columnar crystal layer. The coatings and NdFeB substrate combine well, and moreover, there is occurrence of metallurgy bonding in the interface layer. Both Al and AlN/Al coatings have a good protective ability to NdFeB. Especially, the corrosion resistance of AlN/Al coated NdFeB is improved largely. AlN/Al and Al protective coatings not only do not deteriorate the magnetic properties of NdFeB, but contribute to their slight increase.

Al-Si/Al2O3 in situ composite prepared by displacement reaction of CuO/Al system

Directory of Open Access Journals (Sweden)

Zhang Jing

2010-02-01

Full Text Available Al2O3 particle-reinforced ZL109 composite was prepared by in situ reaction between CuO and Al. The microstructure was observed by means of OM, SEM and TEM. The Al2O3 particles in sub-micron sizes distribute uniformly in the matrix, and the Cu displaced from the in situ reaction forms net-like alloy phases with other alloy elements. The hardness and the tensile strength of the composites at room temperature have a slight increase as compared to that of the matrix. However, the tensile strength at 350 ℃ has reached 90.23 MPa, or 16.92 MPa higher than that of the matrix. The mechanism of the reaction in the CuO/Al system was studied by using of differential scanning calorimetry(DSC and thermodynamic calculation. The reaction between CuO and Al involves two steps. First, CuO reacts with Al to form Cu2O and Al2O3 at the melting temperature of the matrix alloy, and second, Cu2O reacts with Al to form Cu and Al2O3 at a higher temperature. At ZL109 casting temperature of 750–780 ℃, the second step can also take place because of the effect of exothermic reaction of the first step.

AlGaN nanocolumns and AlGaN/GaN/AlGaN nanostructures grown by molecular beam epitaxy

Energy Technology Data Exchange (ETDEWEB)

Ristic, J.; Sanchez-Garcia, M.A.; Ulloa, J.M.; Calleja, E. [Departamento de Ingenieria Electronica, ETSI Telecomunicacion, Universidad Politecnica de Madrid, Ciudad Universitaria, 28040 Madrid (Spain); Sanchez-Paramo, J.; Calleja, J.M. [Departamento de Fisica de Materiales, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Jahn, U.; Trampert, A.; Ploog, K.H. [Paul-Drude-Institut fuer Festkoerperelektronik, Hausvogteiplatz 5-7, 10117 Berlin (Germany)

2002-12-01

This work reports on the characterization of hexagonal, single crystal AlGaN nanocolumns with diameters in the range of 30 to 100 nm grown by molecular beam epitaxy on Si(111) substrates. The change of the flux ratio between the Al and the total III-element controls the alloy composition. The Al composition trend versus the Al flux is consistent both with the E{sub 2} phonon energy values measured by inelastic light scattering and the luminescence emission peaks position. High quality low dimensional AlGaN/GaN/AlGaN heterostructures with five GaN quantum discs, 2 and 4 nm thick, embedded into the AlGaN columns, were designed in order to study the quantum confinement effects. (Abstract Copyright [2002], Wiley Periodicals, Inc.)

RELACIÓN COSTE-BENEFICIO DE LAS POLÍTICAS SOBRE CONSUMO DE TABACO EN EL LUGAR DE TRABAJO

Directory of Open Access Journals (Sweden)

Tamara Raaijmakers

2003-01-01

Full Text Available Este trabajo revisa los motivos que llevan a las empresas a establecer una política sobre control del tabaquismo, los beneficios económicos para la sociedad que se derivan de su adopción, y sus costes, detallados por países en la Unión Europea. Se revisa también la literatura sobre los costes de la aplicación de una política sobre tabaquismo en el ámbito laboral. El principal objetivo de las políticas sobre tabaquismo en el lugar de trabajo es la protección de los empleados del aire contaminado por el humo de tabaco (ACHT. Otros motivos son la reducción de costes; la mejora de la imagen; y la disminución de absentismo, accidentes laborales, conflictos y costes adicionales debidos al tabaco. La protección frente al ACHT no supone mayores costes para la empresa, y se refieren ventajas económicas con su puesta en práctica. Los beneficios sobrepasan con creces las inversiones, en particular a largo plazo, y parecen mayores cuando se establece una prohibición total de fumar en el lugar de trabajo en vez de áreas para fumadores.

Estudio del virus JC, agente causal de la leucoencafalopatía multifocal progresiva, en pacientes de esclerosis múltiple recurrente-remitente tratados con Natalizumab

OpenAIRE

Domínguez Mozo, María Inmaculada

2013-01-01

La esclerosis múltiple (EM) es una enfermedad desmielinizante inflamatoria crónica que afecta al sistema nervioso central (SNC) y cuyo origen es presumiblemente autoinmune, siendo en los países desarrollados la segunda causa de discapacidad entre personas jóvenes después de los accidentes de tráfico. Durante los últimos años se han desarrollado, o actualmente están en ensayo clínico, una gran cantidad de fármacos para tratar esta patología. Entre todos ellos cabe destacar natalizumab, u...

EXPERIENCIA DE ENSINO E APRENDIZAGEM DE FARMACOLOGIA EM MEDICINA VETERINÁRIA, EM ALEGRE- ES

OpenAIRE

Rudison da Silva Florêncio; Mirelle Baptista Jordaim; Débora de Souza Pozzatto; Amanda Maria Miranda Rodrigues dos Santos; Rosilene do Carmo Mendes; Thaís Portes Deorce Pimenta; Gabriela Fiuza Corato; Caio Vaz Baqui Lima; Mariana Corrêa Santos; Lenir Cardso Porfírio

2016-01-01

Em medicina veterinária a farmacologia é uma das disciplinas que une o ciclo básico com o ciclo profissionalizante, sendo constantemente utilizada na clínica médica e suas disciplinas relacionadas, além de possuir importante papel em áreas não relacionadas com clínica, cirurgia e áreas relacionadas. O estudo de farmacologia auxilia na formação de profissionais médicos veterinários, habilitando-os a utilizar os diferentes medicamentos e o conhecimento sobre eles para diagnosticar, tratar e pre...

La ciudad en la identidad cultural bonaerense

OpenAIRE

Vitalone, Cristina

1992-01-01

Entre los primeros interrogantes que aparecen al tratar el tema de la identidad urbano arquitectónica de la provincia de Buenos Aires encontramos aquel que nos refiere a que tipo de legado físico poseemos, cuáles son sus valores y, fundamentalmente, cómo debemos operar hoy sobre ellos. El insuficiente conocimiento de la identidad cultural de esta vasta legión, en la cual la morfología del territorio y la ciudad adquieren un rol preponderante, nos ha impedido abordar, muchas veces, e...

Patrocinio deportivo en los principales equipos de fútbol de la Liga española

OpenAIRE

Trueba Gutiérrez, Manuel

2016-01-01

RESUMEN: El marketing es una función de la organización y un conjunto de procesos para crear, comunicar y entregar valor a los clientes, y para manejar las relaciones con estos últimos, de manera que beneficien a toda la organización”. (AMA, 1985) El objetivo principal de este trabajo es analizar y tratar todo aquello que rodea al mundo del Patrocinio en el fútbol. Concretamente, el valoraremos la notoriedad o importancia de los patrocinadores en los principales equipos de fútbol de la Li...

Creación del área de ventas y mercadeo para Industrias Leader Ltda.

OpenAIRE

Pérez Forero, Gabriel Stiven; Vargas Jiménez, Bibiana

2016-01-01

El departamento de mercadeo y ventas es fundamental en una empresa debido a que es el encargado de desarrollar e implementar estrategias que satisfagan las necesidades y requerimientos del cliente. Es aquí donde más se puede ver reflejado el aumento de las ventas de la empresa. El servicio al cliente, la relación con el mismo y el acompañamiento, es un tema muy importante a tratar, tanto para atraer a nuevos clientes como también para conservar a los clientes actuales. Este trabajo se desarro...

Violencia sexual

OpenAIRE

Carlos Tadayuki Oshikata

2003-01-01

Resumo: A violência sexual é um crime clandestino e subnotificado, praticado contra a liberdade sexual da mulher. Provoca traumas físicos e psíquicos, além de expor a doenças sexualmente transmissíveis e gravidez indesejada. Existem poucos serviços no Brasil que oferecem um atendimento especializado para diagnosticar e tratar as mulheres vítimas de violência sexual. A finalidade deste trabalho foi avaliar, através de um estudo descritivo e retrospectivo, 166 mulheres que compareceram na urgên...

EMPLEO DEL MÉTODO BIOALBERIC EN EL TRATAMIENTO DE LA DIABETES MELLITUS EN CANINOS DOMÉSTICOS / Use of BioAlberic method for treating diabetes mellitus in domestic dogs

OpenAIRE

Yailyn Ramos Morejón; Lázaro Pérez Ramos; Aimée Álvarez Álvarez; Raisa Olano Justiniani; Jesús A. Ramírez López; Deneb González Rodríguez; Beatriz Hugues Hernandorena

2013-01-01

Resumen: La diabetes mellitus es una enfermedad frecuente en los caninos domésticos, en la cual pueden presentarse alteraciones del sistema cardiovascular, difíciles de tratar. Una de las vías alternativas de tratamiento en este tipo de animales pudiera ser el empleo del método BioAlberic. En este artículo se presentan los resultados obtenidos en la aplicación de este método (con el producto Rapsul) al iniciar el tratamiento de la diabetes mellitus en dos perros domésticos, como parte del pro...

Los modelos de generación de oleaje de viento: características, evolución y futuras aplicaciones en colombia

OpenAIRE

MONTOYA RAMÍREZ, RUBÉN DARÍO; OSORIO ARIAS, ANDRÉS

2009-01-01

Durante el siglo pasado diferentes autores presentaron sus teorías sobre el oleaje basados en las leyes de la física relacionadas con el movimiento ondulatorio, estas teorías hicieron representaciones de las olas del mar como ondas de amplitud finita o de amplitud pequeña en las cuales la interacción entre ondas podía considerarse como lineal; sin embargo quedaron incompletas al tratar de explicar los mecanismos físicos relacionados con el crecimiento del oleaje. Sólo fue hasta mediados del ...

Paisaje, territorio, emoción

OpenAIRE

Linaza Iglesias, Marta; Mañero Rodicio, Javier

2017-01-01

Las prácticas artísticas contemporáneas vinculadas al paisaje tienen desde su aparición un fuerte componente corporal. El cuerpo interviene, si es que no es directamente depositario de sus aspiraciones. Así, por mucho que desde posturas recientes se pretenda reducir la experiencia del paisaje a la más política del territorio, la pulsión esencialista con que nacieron aquellas prácticas, permanece. No se trataría de negar una aproximación crítica y territorializada, sino de recuperar la esencia...

Detección de Estructuras de Personalidad en Alumnos Adolescentes de Educación Especial

OpenAIRE

Toro i Recasens, Laia

2007-01-01

Cómo tratar con la diferencia de los alumnos en los centros educativos es una cuestión de creciente interés en nuestro país, cuyas cifras referentes al fracaso escolar son cada vez más preocupantes. Los alumnos adolescentes que presentan dificultades en el aprendizaje, muestran a menudo problemas en su personalidad. El papel que tiene la personalidad en el alumnado que requiere necesidades educativas especiales es el tema que abordamos en el presente estudio.MÉTODO:Aplicamos el IA-TP (Tous, P...

Polímeros biodegradables a partir del almidón de yuca

OpenAIRE

Ruíz Avilés, Gladys

2005-01-01

Los polímeros tradicionales tienen gran cantidad de aplicaciones especialmente en la industria del empaque, donde se consume un número de toneladas al año, bastante considerable -- Sin embargo, tienen dos desventajas que es necesario tenerlas en cuenta y tratar de resolver los problemas que ocasionan -- La primera es que son fabricados a partir de materias primas obtenidas de recursos no renovables, como el petróleo, que cada día se hace más escaso y por ende más costoso -- La segunda es su p...

Implantación del Sistema de Calidad ISO 9001 en VECOPOL S.L.

OpenAIRE

González, Berta

2012-01-01

En este trabajo trataré de desarrollar e implantar el Sistema de Calidad ISO 9001 en la empresa VECOPOL S.L. El objetivo que me planteo es desarrollar parte de la documentación del Sistema de Calidad ISO 9001 e iniciar su implantación de forma que se empiece a trabajar en un entorno de calidad, con el propósito fundamental de satisfacer al cliente. En un futuro, si la empresa lo considera conveniente, se podrá certificar el Sistema de Gestión de Calidad.

Proyecto constructivo de la EDAR de Harsova, Rumanía

OpenAIRE

Lloret Batlle, Roger

2012-01-01

El objeto del presente proyecto consiste en la definición precisa de las obras que requerirá la construcción de la EDAR de Harsova. La razón de ser y justificación del proyecto se hace patente ante la necesidad social, medio ambiental y de salubridad de poner fin a los vertidos de aguas residuales sin tratar al cauce público. Es evidente, por tanto, la urgencia de un proyecto de Estación Depuradora de Aguas Residuales (EDAR) para el municipio con una línea de tratamiento ade...

Modelo multicritério para seleção de portfolio de projetos considerando sinergia

OpenAIRE

DUARTE, Marina Dantas de Oliveira

2007-01-01

O trabalho desenvolvido objetiva tratar o problema de seleção de portfolio de projetos e as particularidades que envolve. Apesar do considerável volume de estudos existentes, ainda não há um consenso quanto aos elementos que caracterizam esta abordagem, pois a maioria dos trabalhos utiliza o termo seleção de portfolio para designar seleção de projetos. Além disso, a existência de sinergia entre projetos é pouco abordada nos modelos que se propõem a resolver o problema. Portanto...

Qualidade, compostos bioativos e atividade antioxidante de variedades de videiras do Banco Ativo de Germoplasma da Embrapa Semiárido

OpenAIRE

Batista, Patrício Ferreira

2014-01-01

A sociedade moderna busca, cada vez mais, o consumo de alimentos que possam tratar e prevenir doenças, bem como aumentar a longevidade. Entre estes, destacam-se os alimentos funcionais, incluindo bebidas, ricos em compostos antioxidantes com ação benéfica à saúde já comprovada, como uvas e os seus derivados. Em vista disto, um estudo foi conduzido com o objetivo de identificar variedades de uvas destinadas ao consumo in natura e ao processamento que, além de atender aos requerimentos de quali...

Evaluación de tratamientos de hidrofugación aplicados a piedras de catedrales andaluzas. II. Ensayo de cristalización de sales

OpenAIRE

Villegas Sánchez, R.; Vale Parapar, J. F.

1993-01-01

En un artículo anterior se han evaluado los cambios producidos en las propiedades relacionadas con el acceso y movimiento de agua en la piedra como consecuencia de la aplicación de tratamientos de hidrofugación. En este trabajo se compara la resistencia a la alteración producida por sales de las probetas tratadas y sin tratar, sometiéndolas al ensayo de cristalización de sulfato sódico. Tras finalizar el ensayo (75 ciclos) se han medido nuevamente las propiedades relacionadas con el a...

Simulación hidrológica

Directory of Open Access Journals (Sweden)

Carlos A. González M.

1989-07-01

Full Text Available Las tendencias del modelamiento en hidrología dependen del problema a tratar. En general, se describe cualquier subsistema del ciclo hidrológico como un sistema y se representa en forma de modelo estocástico o determinístico; en ambos casos se puede realizar simulación en computador dependiendo del modelo propuesto. Con relación al modelamiento estocástico se hace énfasis en la búsqueda actual de modelos robustos para el análisis de caudales anuales máximos.

Monitorización de un lecho fluidizado mediante acelerometría

OpenAIRE

Velasco Fernández, Mario

2013-01-01

El presente proyecto estudiará la posibilidad de monitorizar un reactor químico mediante sensores de vibración. Actualmente, no se realiza este tipo de monitorización sobre reactores químicos, y los estudios realizados al respecto son escasos. Se tratarán de establecer las posibles equivalencias entre las medidas realizadas con sensores de presión y de vibración. Para ello se realizará la monitorización de un modelo de reactor a escala, del laboratorio de la Universidad, utilizand...

Desigualdad o pobreza

OpenAIRE

Osta Garatea, Rubén

2017-01-01

¿Cómo afecta el crecimiento económico a la distribución de la riqueza, al desarrollo y a la pobreza mundial? ¿Es posible reducir la desigualdad y la pobreza mediante un sistema de mercado y propiedad privada? O ¿es el sistema capitalista el causante de la pobreza y la desigualdad? ¿Qué concepto es más amenazador para los principios morales de las sociedades democráticas? ¿La desigualdad o la pobreza? En este ensayo trataré de responder de la mejor manera posible a estas cuestio...

Cine vasco y euskera: debates de identidad

OpenAIRE

Fernández, Joxean

2013-01-01

INTRODUCCIÓN: LA ÓSMOSIS HISTORIA-CINE Los físicos suelen hablar de ósmosis para referirse al paso recíproco de dos líquidos de distinta densidad a través de una membrana semipermeable que los separa. Asimismo, en lenguaje literario, hablamos de ósmosis para definir simplemente influencias recíprocas. Nos permitimos utilizar aquí este término prestado de otras disciplinas científicas para tratar de obtener una imagen de las relaciones que el cine y la historia vienen manteniendo desde que aqu...

La Inversion Extranjera Directa (IED, teorias y practicas.

Directory of Open Access Journals (Sweden)

De la Garza, U.

2005-01-01

Full Text Available En éste articulo, analizaremos algunas de las principales teorías relacionadas con la IED. Se destacarán principalmente los aportes teóricos en cuanto a posibles efectos positivos y negativos de la llegada de IED a economías receptoras. Al mismo tiempo, se tratará de resaltar y justificar la importancia de la llegada de nuevas inversiones a países en desarrollo como México, destacando los principales factores que propician la llegada de IED en países en desarrollo.

Descripción funcional y física de sistemas de tratamiento de equipajes

OpenAIRE

Antón Atienza, Ramón

2009-01-01

Aunque de los aeropuertos la parte que más se conozca sea la del tratamiento al pasajero, desde los mostradores de facturación hasta las puertas de embarque, pasando por los controles de seguridad incluso por las tiendas que se encuentran en el lado aire del aeropuerto, el tratamiento de maletas o equipajes es cada vez más importante. Se ha generado la necesidad de tratar dichos equipajes salientes en el mínimo tiempo posible, con la máxima eficiencia y la máxima seguridad posible, inspeccion...

La píldora anticonceptiva, ¿una droga de "estilo de vida"?: Ensayo sobre el proceso actual de medicalización de la sexualidad

OpenAIRE

Nucci,Marina

2012-01-01

Este artículo discute el proceso de medicalización de la sexualidad, reflexionando sobre la píldora anticonceptiva hormonal y su relación con el concepto de drogas de estilo de vida (entendido como medicamentos no necesariamente utilizados para tratar una afección, sino para mejorar la vida de las personas). La píldora anticonceptiva, lanzada en Estados Unidos en 1957, desde su creación estuvo destinada al uso cotidiano de mujeres saludables, y se convirtió en un importante símbolo cultural, ...

Análisis de vulnerabilidades de protocolos de protección y autenticación inalámbrico para el aceso seguro en redes Wifi

OpenAIRE

Ramos Valencia, Marco Vinicio

2012-01-01

Las redes wireless se difunden con rapidez, gran comodidad y ventajas que suponen estas nuevas tecnologías de conexión generando que muchísimos usuarios no se hayan percatado de los peligros a que están expuestas las redes wireless (al no haber ya una conexión física).Es así que el crecimiento desmedido de conexiones sin cable ha creado la curiosidad de muchos a tratar de interferir en estas, logrando en muchos de los casos obtener claves de acceso, negar el servicio o realizar suplantaciones...

Paisaje forestal y representación social en Castilla (siglos XIV-XVI. Los montes de San Salvador de Oña (Burgos

Directory of Open Access Journals (Sweden)

Francisco REYES TÉLLEZ

2014-12-01

Full Text Available El objetivo principal de este artículo es tratar de analizar la representación social del paisaje forestal perteneciente al señorío del monasterio de San Salvador de Oña (Burgos, durante los siglos XIV-XVI, a partir de las descripciones que se realizan del mismo en la documentación judicial relacionada con pleitos, pesquisas, etc. por el uso y aprovechamiento de los bosques y montes, para procurar conocer cuál era la construcción simbólica de esos paisajes de los distintos agentes sociales, e intentar valorar si esa forma de aproximarnos al territorio nos puede aportar nuevos enfoques o posibilidades de interpretación en el estudio de esa realidad.

KONSEPSI AL-QURAN DAN AL-HADITS TENTANG OPERASIONAL BANK SYARIAH

Directory of Open Access Journals (Sweden)

Muhammad Ardy Zaini

2015-01-01

Full Text Available Islam hadir dengan beberapa tujuan, diantaranya adalah terciptanya khoirul ummah dan rahmatan lil’alamin dengan al-Qur’an dan al-Hadits sebagai penuntun umat Islam demi tercapainya tujuan tersebut. Sebagai pedoman hidup, al-Qur’an dan al-Hadits memberikan berbagai petunjuk tentang keteraturan dan permasalahan hidup, termasuk didalamnya mengenai perbankan yang telah memenuhi hampir separuh sisi-sisi kehidupan manusia. Untuk memaksimal ajaran syariah secara kaffah, maka nilai-nilai yang terdapat dalam al-Quran harus mampu diturunkan pada tataran praktis. Salah satu usaha dan langkah dalam rangka menemukan formula perbankan masa depan, al-Quran dan Hadits memiliki konsepsi dalam kegiatan operasional Bank Syariah. Hal ini dilakukan untuk membentuk sikap mental atau watak yang terjabarkan dalam pola berpikir, cara berbicara, dan etika bertingkah laku, sebagai ekspresi jiwa dari manusia yang beriman dan bertakwa kepada Allah Swt. Agar umat Islam mampu menjadi umat yang unggul (khayr ummah.

Fabrication of AlN-TiC/Al composites by gas injection processing

Institute of Scientific and Technical Information of China (English)

YU Huashun; CHEN Hongmei; MA Rendian; MIN Guanghui

2006-01-01

The fabrication of AlN-TiC/Al composites by carbon-and nitrogen-containing gas injection into Al-Mg-Ti melts was studied. It was shown that AlN and TiC particles could be formed by the in situ reaction of mixture gas (N2+C2H2+NH3) with Al-Mg-Ti melts. The condition for the formation of AlN was that the treatment temperature must be higher than 1373 K, and the amounts of AlN and TiC increased with the increase of the treatment temperature and the gas injection time.It was considered that AlN was formed by the direct reaction of Al with nitrogen-containing gas at the interface of the gas bubble and the melt. However, the mechanism of TiC formation is a combination mechanism of solution-precipitation and solid-liquid reaction.

The formation of AlB2 in an Al-B master alloy

International Nuclear Information System (INIS)

Wang Xiaoming

2005-01-01

The formation of borides in an Al-3 wt.%B master alloy, produced via chemical reactions of KBF 4 and aluminium has been investigated. The chemical reactions produce boron, which dissolves into molten aluminium and subsequently forms aluminium borides. Backscattered electron imaging (BEI) of the Al-3 wt.%B master alloy under a scanning electron microscope (SEM) revealed the presence of two types of phases that contain different levels of boron. Combined with X-ray diffraction (XRD) results, the two types of phases are identified as AlB 2 on AlB 12 . This gives a direct evidence for a peritectic reaction of AlB 12 and aluminium, which produces AlB 2 . The thermodynamic properties of the reactions that may be involved are examined, and the presence of AlB 12 phase in the master alloy explained. The observed microstructure is explained according to the peritectic reaction in an Al-B phase diagram. The stability of AlB 2 and AlB 12 at lower temperature than 975 deg. C is clarified

Construction and evaluation of multi-component Zn-Al based bearing alloys (Zn-Al-Si, Zn-Al-Cu)

International Nuclear Information System (INIS)

Shahmiri, M.; Shahin, K.

2001-01-01

Zn-Al based alloys, with excellent mechanical properties, are finding increasing applications in various industries, especially bearing and bushing fields. Observed dimensional instabilities, in their multicomponent systems, (e. g. Zn-Al-Si and, Zn-Al Si-Cu), is believed to be as the result of some kinds of phase transformation, due to the temperature variations, while in service. Profound understanding of the phase transformations due to the temperature variation, requires detailed evaluations of the isothermal sections of the multi-components phase diagrams of Zn-Al-Si and, Zn-Al-Si-Cu alloy systems. In the present article, the isothermal sections of the aforementioned ternary and quaternary systems in the solid state regions have been investigated and observed phase transitions have been critically evaluated

The Existence of a Designer Al=Al Double Bond in the LiAl2 H4- Cluster Formed by Electronic Transmutation.

Science.gov (United States)

Lundell, Katie A; Zhang, Xinxing; Boldyrev, Alexander I; Bowen, Kit H

2017-12-22

The Al=Al double bond is elusive in chemistry. Herein we report the results obtained via combined photoelectron spectroscopy and ab initio studies of the LiAl 2 H 4 - cluster that confirm the formation of a conventional Al=Al double bond. Comprehensive searches for the most stable structures of the LiAl 2 H 4 - cluster have shown that the global minimum isomer I possesses a geometric structure which resembles that of Si 2 H 4 , demonstrating a successful example of the transmutation of Al atoms into Si atoms by electron donation. Theoretical simulations of the photoelectron spectrum discovered the coexistence of two isomers in the ion beam, including the one with the Al=Al double bond. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

El coste del seguimiento farmacoterapéutico en una farmacia comunitaria (II: costes de funcionamiento del servicio

Directory of Open Access Journals (Sweden)

Cobián Rodríguez MB

2014-09-01

Full Text Available Introducción: El seguimiento farmacoterapéutico es un servicio que atiende las necesidades de los enfermos crónicos polimedicados pero invierte muchos recursos en un solo paciente. El objetivo del estudio fue conocer las variaciones en la dispensación de medicamentos derivadas del seguimiento farmacoterapéutico y determinar los recursos invertidos en el funcionamiento y sus costes asociados. Métodos: Se realizó el servicio de seguimiento farmacoterapéutico durante seis meses de una muestra de 20 pacientes seleccionados en función del riesgo de presentar RNM utilizando el método Dáder. Se registraron los recursos materiales, de información y humanos utilizados y se calculó su coste. Resultados: El número de medicamentos dispensado a los pacientes del programa disminuyó un 8,4 %. El coste del servicio de SFT de un paciente medio fue de 87 euros en los seis meses de estudio, siendo mayor en los pacientes que presentaban un mayor riesgo de presentar RNM Discusión: El servicio de SFT disminuye los ingresos de la farmacia al disminuir la dispensación de medicamentos y supone un coste para la farmacia relacionado fundamentalmente con el tiempo de trabajo de los farmacéuticos. Desde el punto de vista del pagador, el ahorro en medicamentos pagaría la mayor parte de este servicio.

Aluminium alloyed iron-silicide/silicon solar cells: A simple approach for low cost environmental-friendly photovoltaic technology.

Science.gov (United States)

Kumar Dalapati, Goutam; Masudy-Panah, Saeid; Kumar, Avishek; Cheh Tan, Cheng; Ru Tan, Hui; Chi, Dongzhi

2015-12-03

This work demonstrates the fabrication of silicide/silicon based solar cell towards the development of low cost and environmental friendly photovoltaic technology. A heterostructure solar cells using metallic alpha phase (α-phase) aluminum alloyed iron silicide (FeSi(Al)) on n-type silicon is fabricated with an efficiency of 0.8%. The fabricated device has an open circuit voltage and fill-factor of 240 mV and 60%, respectively. Performance of the device was improved by about 7 fold to 5.1% through the interface engineering. The α-phase FeSi(Al)/silicon solar cell devices have promising photovoltaic characteristic with an open circuit voltage, short-circuit current and a fill factor (FF) of 425 mV, 18.5 mA/cm(2), and 64%, respectively. The significant improvement of α-phase FeSi(Al)/n-Si solar cells is due to the formation p(+-)n homojunction through the formation of re-grown crystalline silicon layer (~5-10 nm) at the silicide/silicon interface. Thickness of the regrown silicon layer is crucial for the silicide/silicon based photovoltaic devices. Performance of the α-FeSi(Al)/n-Si solar cells significantly depends on the thickness of α-FeSi(Al) layer and process temperature during the device fabrication. This study will open up new opportunities for the Si based photovoltaic technology using a simple, sustainable, and los cost method.

Cost estimation in software engineering projects with web components development

Directory of Open Access Journals (Sweden)

Javier de Andrés

2015-01-01

Full Text Available Existen multitud de modelos propuestos para la predicción de co stes en proyectos de software, al gunos orientados específicamen te para proyectos Web. Este trabajo analiza si los modelos específicos para proyectos Web están justifi cados, examinando el comportami ento diferencial de los costes entre proyectos de desarrollo softwar e Web y no Web. Se analizan dos aspectos del cálculo de costes: las deseconomías de escala, y el im pacto de algunas características de estos proyectos que son utilizadas como cost drivers. Se en uncian dos hipótesis: (a en estos proyect os las deseconomías de escala so n mayores y (b el incremento de coste que provocan los cost dr ivers es menor para los proyectos Web. Se contrastaron estas hipótesis a nalizando un conjunto de proyectos reales. Los resultados sugie ren que ambas hipótesis se cumplen. Por lo tanto, la principal contribu ción a la literatura de esta inv estigación es que el desarrollo de modelos específicos para los proyectos Web está justificado.

Aproximación Neuropsicológica al Constructo de Empatía: Aspectos Cognitivos y Neuroanatómicos

Directory of Open Access Journals (Sweden)

Vanessa Arán Filippetti

2012-01-01

Full Text Available Los modelos integradores definen a la empatía como un constructo multidimensional que incluye aspectos afectivos (EA; empatía afectiva y aspectos cognitivos (EC; empatía cognitiva. El objetivo del presente trabajo es exponer el estado del arte de la asociación entre la empatía y las funciones ejecutivas (FE y tratar de proponer una integración de las ideas al respecto. Para esto, se adopta un marco conceptual y se revisan estudios que conciben a la EA y a la EC como aspectos complementarios pero diferenciados tanto desde el punto de vista funcional como neurobiológico; ambos componentes se activarían conjuntamente durante la interacción social, pero podrían actuar por separado tal como se evidencia, por ejemplo, en el daño cerebral y en la psicopatología. Desde una perspectiva multidimensional, la relación empatía-FE podría explicarse a partir de la relación ECfTeoría de la MenteFE, así como mediante un modelo que admita la influencia de procesos top-down - a través de funciones ejecutivas - en el proceso empático. Adoptar una visión multidimensional de la empatía no sólo es relevante desde el punto de vista funcional, sino que aporta evidencia significativa para el diagnóstico, la evaluación y la comprensión del déficit empático en la clínica neurológica y psiquiátrica.

Characterization of N-polar AlN in GaN/AlN/(Al,Ga)N heterostructures grown by metal-organic chemical vapor deposition

Science.gov (United States)

Li, Haoran; Mazumder, Baishakhi; Bonef, Bastien; Keller, Stacia; Wienecke, Steven; Speck, James S.; Denbaars, Steven P.; Mishra, Umesh K.

2017-11-01

In GaN/(Al,Ga)N high-electron-mobility transistors (HEMT), AlN interlayer between GaN channel and AlGaN barrier suppresses alloy scattering and significantly improves the electron mobility of the two-dimensional electron gas. While high concentrations of gallium were previously observed in Al-polar AlN interlayers grown by metal-organic chemical vapor deposition, the N-polar AlN (Al x Ga1-x N) films examined by atom probe tomography in this study exhibited aluminum compositions (x) equal to or higher than 95% over a wide range of growth conditions. The also investigated AlN interlayer in a N-polar GaN/AlN/AlGaN/ S.I. GaN HEMT structure possessed a similarly high x content.

KRITIK ATAS KRITIK EPISTEMOLOGI TAFSIR M. ABIED AL JABIRI: Studi Kritis atas Madkhal ila al Quran al Karim

Directory of Open Access Journals (Sweden)

Ahmad Fawaid

2015-12-01

Full Text Available This paper critically views the epistemology of Muhammad Abid al Jabiri’s interpretation in his book, Madkhal ila al Quran al Karim. His latest work is projected to make the Quran relevant to mankind today and with certainly critiquing classical Quranic studies that have been constructed by previous scholars. Starting from Arab criticism, which is expected to synergize the gap between Turath and modernity, al Jabiri tried out his theory in the realm of Quranic studies oriented to maintain its originality and interpretation from sectarian influence. Focusing on al Jabiri’s review on the Quran, this paper examines and associates some of the problems with the epistemology of critique in Arab reasoning. Finally, it is inferred that the epistemologic offer of al Jabiri used in Turath is not fully applicable in Quranic studies for several reasons. First, the Quranic studies existed within the chain of sanad in its formation. Secondly, at the application stage, al Jabri often overlooked the sanad and narrations from the companions.

Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

International Nuclear Information System (INIS)

Li, Shuo; Bhushan, Bharat

2016-01-01

Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

Lubrication performance and mechanisms of Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxide nanoparticles as lubricant additives

Energy Technology Data Exchange (ETDEWEB)

Li, Shuo [School of Materials Science and Technology, China University of Geosciences (Beijing), 29 Xueyuan Road, Haidian Distract, Beijing 100083 (China); Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States); Bhushan, Bharat, E-mail: bhushan.2@osu.edu [Nanoprobe Laboratory for Bio- & Nanotechnology and Biomimetics (NLBB), The Ohio State University, 201 W. 19th Avenue Columbus, OH 43210-1142 (United States)

2016-08-15

Highlights: • Mg/Al-, Zn/Al- and Zn/Mg/Al-layered double hydroxide were synthesized. • Mg/Al-LDH had superior tribological performance compared to other LDHs. • The best thermal stability of Mg/Al-LDH was responsible for its friction property. - Abstract: Solid lubricant particles are commonly used as oil additives for low friction and wear. Mg/Al-, Zn/Al-, and Zn/Mg/Al-layered double hydroxides (LDH) were synthesized by coprecipitation method. The benefits of LDH nanoparticles are that they can be synthesized using chemical methods where size and shape can be controlled, and can be modified organically to allow dispersal in fluids. The LDH nanoparticles were characterized by X-ray diffraction, scanning electron microscope, thermogravimetry, and differential scanning calorimetry. A pin-on-disk friction and wear tester was used for evaluating the friction and wear properties of LDH nanoparticles as lubricant additives. LDH nanoparticles have friction-reducing and anti-wear properties compared to oil without LDHs. Mg/Al-LDH has the best lubrication, possibly due to better thermal stability in severe conditions.

Dakwah Kultural Bayt al-Qur’an al-Akbar Ukiran Kayu Khas Melayu Palembang

Directory of Open Access Journals (Sweden)

Reza Pahlevi

2016-07-01

Full Text Available Penelitian ini berusaha mengungkap berbagai fenomena yang menggambarkan serangkaian kegiatan dakwah kultural Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang. Sehingga dapat diperoleh sejumlah informasi mengenai berbagai upaya penerapan program yang dimaksud. Penelitian ini dapat disimpulkan, pertama kontribusi Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang terhadap perkembangan metode dakwah kultural adalah dakwah melalui seni. Kedua, Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang sebagai tempat Wisata Religi yang sangat signifikan.   This research tries to reveal the various phenomenon that describe a series of cultural propaganda activities Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang. In order to obtain some informations about the efforts of the implementation of the program in question. It can be concluded, the first contribution of Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang on the development of methods of cultural propaganda is propaganda through art. Second Bayt al-Qur’an al-Akbar Ukiran Khas Melayu Palembang as a very significant Religious Tourism.

Optical phonon scattering on electronic mobility in Al2O3/AlGaN/AlN/GaN heterostructures

Science.gov (United States)

Zhou, X. J.; Qu, Y.; Ban, S. L.; Wang, Z. P.

2017-12-01

Considering the built-in electric fields and the two-mode property of transverse optical phonons in AlGaN material, the electronic eigen-energies and wave functions are obtained by solving Schrödinger equation with the finite difference method. The dispersion relations and potentials of the optical phonons are given by the transfer matrix method. The mobility of the two dimensional electron gas influenced by the optical phonons in Al2O3/AlGaN/AlN/GaN heterostructures is investigated based on the theory of Lei-Ting force balance equation. It is found that the scattering from the half-space phonons is the main factor affecting the electronic mobility, and the influence of the other phonons can be ignored. The results show that the mobility decreases with increasing the thicknesses of Al2O3 and AlN layers, but there is no definite relationship between the mobility and the thickness of AlGaN barrier. The mobility is obviously reduced by increasing Al component in AlGaN crystal to show that the effect of ternary mixed crystals is important. It is also found that the mobility increases first and then decreases as the increment of the fixed charges, but decreases always with increasing temperature. The heterostructures constructed here can be good candidates as metal-oxide-semiconductor high-electron-mobility-transistors since they have higher electronic mobility due to the influence from interface phonons weakened by the AlN interlayer.

Fabrication and Mechanical Properties of Nanostructured TiC-TiAl by the Pulsed Current Activated Sintering

Energy Technology Data Exchange (ETDEWEB)

Kwak, Bong-Won; Shon, In-Jin [Chonbuk National University, Chonbuk (Korea, Republic of); Kim, Byung-Su [Korea Institute of Geoscience and Mineral Resources, Daejeon (Korea, Republic of); Yoon, Jin-Kook; Hong, Kyung-Tae [Korea Institute of Science and Technology, Seoul (Korea, Republic of)

2016-08-15

TiC-Co or TiC-Ni hard materials have been used for cutting tools. However, the high cost and the low hardness of Ni or Co, and the low corrosion resistance of the TiC-Ni and TiC-Co cermets have generated interest in recent years in using them as alternative binder phases. In this study, TiAl was used as a novel binder and consolidated by the pulsed current activated sintering(PCAS) method. Nanopowders of TiC and TiAl were fabricated using high energy ball milling. Highly dense TiC-TiAl hard materials with a relative density of up to 99.5% were sintered within three min by PCAS. Not only the hardness but also the fracture toughness of the TiC-10 vol%TiAl were better than those of TiC-10 vol%Ni or TiC-10 vol%Co.

Fabrication and Mechanical Properties of Nanostructured TiC-TiAl by the Pulsed Current Activated Sintering

International Nuclear Information System (INIS)

Kwak, Bong-Won; Shon, In-Jin; Kim, Byung-Su; Yoon, Jin-Kook; Hong, Kyung-Tae

2016-01-01

TiC-Co or TiC-Ni hard materials have been used for cutting tools. However, the high cost and the low hardness of Ni or Co, and the low corrosion resistance of the TiC-Ni and TiC-Co cermets have generated interest in recent years in using them as alternative binder phases. In this study, TiAl was used as a novel binder and consolidated by the pulsed current activated sintering(PCAS) method. Nanopowders of TiC and TiAl were fabricated using high energy ball milling. Highly dense TiC-TiAl hard materials with a relative density of up to 99.5% were sintered within three min by PCAS. Not only the hardness but also the fracture toughness of the TiC-10 vol%TiAl were better than those of TiC-10 vol%Ni or TiC-10 vol%Co.

Al2O3 adherence on CoCrAl alloys

International Nuclear Information System (INIS)

Kingsley, L.M.

1980-04-01

Adherence of protective oxides on NiCrAl and CoCrAl superalloys has been promoted by a dispersion of a highly oxygen reactive element or its oxide being produced within the protection system. Two aspects of this subject are investigated here: the use of Al 2 O 3 as both the dispersion and protective oxide; and the production of an HfO 2 dispersion while simultaneously aluminizing the alloy. It was found that an Al 2 O 3 dispersion will act to promote the adherence of an external scale of Al 2 O 3 to a degree comparable to previously tested dispersions and an HfO 2 dispersion comparable to that produced by a Rhines pack treatment is produced during aluminization

Mechanical Behavior of a Low-Cost Ti-6Al-4V Alloy

Science.gov (United States)

Casem, D. T.; Weerasooriya, T.; Walter, T. R.

2018-01-01

Mechanical compression tests were performed on an economical Ti-6Al-4V alloy over a range of strain-rates and temperatures. Low rate experiments (0.001-0.1/s) were performed with a servo-hydraulic load frame and high rate experiments (1000-80,000/s) were performed with the Kolsky bar (Split Hopkinson pressure bar). Emphasis is placed on the large strain, high-rate, and high temperature behavior of the material in an effort to develop a predictive capability for adiabatic shear bands. Quasi-isothermal experiments were performed with the Kolsky bar to determine the large strain response at elevated rates, and bars with small diameters (1.59 mm and 794 µm, instrumented optically) were used to study the response at the higher strain-rates. Experiments were also conducted at temperatures ranging from 81 to 673 K. Two constitutive models are used to represent the data. The first is the Zerilli-Armstrong recovery strain model and the second is a modified Johnson-Cook model which uses the recovery strain term from the Zerilli-Armstrong model. In both cases, the recovery strain feature is critical for capturing the instability that precedes localization.

COST 507: Thermophysical properties of light metal alloys. Final report

Energy Technology Data Exchange (ETDEWEB)

Jaroma-Weiland, G; Brandt, R; Neuer, G

1994-02-15

The thermophysical properties of Al-, Mg- and Ti-based light metal alloys have been studied by reviewing the literature published so far, evaluating the empirical results and by empirical investigations. The properties to the covered in the literature research are: thermal conductivity, thermal diffusivity, specific heat capacity, thermal expansion and electrical resistivity. The data have been stored in the factual data base THERSYST together with the results of experimental measurements supplied from participants of the COST 507-action (Group D). Altogether 1325 data-sets referring to 146 alloys have been stored. They have been uniformly represented and critically analyzed by means of the THERSYST program moduli. These numerical data cover a number of systems with variing chemical composition and thermal treatment. Partly large discrepancies especially of the thermal conductivity have been found for similar alloys. The problem of experimental uncertainities has been studied in detail by investigation of AA-8090 alloy (Al-2.5Li-1.1Cu). The thermophysical properties of monolithic alloy KS1275 (AlSi12CuNi) and metal matrix composite (KS1275 reinforced with Al2O3 short fibre) have been determined experimentally. (orig.)

Tracing Al Shabaab’s Decision to Cooperate with Al Qaeda in Somalia (2008

Directory of Open Access Journals (Sweden)

Adlini Ilma Ghaisany Sjah

2014-02-01

Full Text Available 'Al Shabaab, a Somali insurgent with predominantly nationalistic causes (alongside transnational [global Jihad] and Islamic goals made the choice to fight on behalf of Al Qaeda in 2008. The decision to do so contrasted with Al Shabaab’s previous behaviour of actively denying cooperation and distancing itself from Al Qaeda. This study aims to uncover factors that contributed to Al Shabaab’s decision through the use of process-tracing. The results show that Al Shabaab’s declaration of cooperation with Al Qaeda in August 2008 was brought about by a series of events that traced back to four factors: public reactions to the implementation of a Salafi ideology, the shift to a radical leadership, Al Shabaab’s inability to maintain stability in areas under its control and its increasing attacks by Al Shabaab on the Somali public. Al Shabaab pursued cooperation with Al Qaeda after realizing that their nationalistic preference was no longer achievable in the near future.' ' '

A Prospective Analysis of the Costs, Benefits, and Impacts of U.S. Renewable Portfolio Standards

Energy Technology Data Exchange (ETDEWEB)

Mai, Trieu [National Renewable Energy Lab. (NREL), Golden, CO (United States); Wiser, Ryan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Barbose, Galen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Bird, Lori [National Renewable Energy Lab. (NREL), Golden, CO (United States); Heeter, Jenny [National Renewable Energy Lab. (NREL), Golden, CO (United States); Keyser, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Krishnan, Venkat [National Renewable Energy Lab. (NREL), Golden, CO (United States); Macknick, Jordan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Millstein, Dev [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2016-12-31

As states have gained experience with renewable portfolio standards (RPS) policies, many have made significant revisions to existing programs. In 2015 and 2016, seven states raised and extended their final RPS targets, while another state enacted a new RPS policy (Barbose 2016b). Interest in expanding and strengthening state RPS programs may continue, while efforts like recent proposals in many states to repeal or freeze existing RPS policies may also persist. In either context, questions about the potential costs, benefits, and other impacts of RPS programs are usually central to the decision-making process. This report follows on previous analyses that have focused on the historical costs, benefits, and other impacts of existing state RPS programs (Heeter et al. 2014; Wiser et al. 2016a). This report examines RPS outcomes prospectively, considering both current RPS policies as well as a potential expansion of those policies. The goal of this work is to provide a consistent and independent analytical methodology for that examination. This analysis relies on National Renewable Energy Laboratory’s (NREL’s) Regional Energy Deployment System (ReEDS) model to estimate changes to the U.S. electric power sector across a number of scenarios and sensitivity cases, focusing on the 2015–2050 timeframe. Based on those modeled results, we evaluate the costs, benefits, and other impacts of renewable energy contributing to RPS compliance using the suite of methods employed in a number of recent studies sponsored by the U.S. Department of Energy (DOE): a report examining retrospective benefits and impacts of RPS programs (Wiser et al. 2016a), the Wind Vision report (DOE 2015), the On the Path to SunShot report focusing on environmental benefits (Wiser et al. 2016b), and the Hydropower Vision report (DOE 2016).

All About ALS

Science.gov (United States)

... Subscribe August 2015 Print this issue All About ALS Understanding a Devastating Disorder En español Send us ... Sports Concussions Wise Choices How Can I Help ALS Research? If you have ALS, join the National ...

Atomistic simulations of diffusion mechanisms in off-stoichiometric Al-rich Ni3Al

International Nuclear Information System (INIS)

Duan, Jinsong

2007-01-01

This paper presents dynamics simulation results of diffusion in off-stoichiometric Al-rich Ni 3 Al (Ni 73 Al 27 ) at temperature ranging from 1300 to 1550 K. The interatomic forces are described by the Finnis-Sinclair type N-body potentials. Particular attention is devoted to the effect of the extra 2% of Al atoms sitting on the Ni sublattice as antisite point defects (Al Ni ) on diffusion. Simulation results show that Ni atoms mainly diffuse through the Ni sublattice at the temperatures investigated. Al atoms diffuse via both the intrasublattice and antistructure bridge (ASB) mechanisms. The contribution to Al diffusion from the ASB mechanism decreases at the lower temperature (T Ni ) enhances both Al and Ni diffusion in Ni 73 Al 27 . The Ni-Al coupled diffusion effect is observed and understood at the atomic level for the first time

Desarrollo de un modelo de simulación utilizando Sistemas Multi-Agente (SMA) aplicado al juego de la cerveza en el software Anylogic®

OpenAIRE

Uribe Vásquez, Juan Alejandro

2015-01-01

La simulación basada en sistemas multi-agentes (SMA) es un nuevo método de simulación que permite tratar de una manera sencilla la complejidad, la emergencia, y la no-linealidad típica de ciertos fenómenos en diversos ámbitos profesionales (medicina, bolsa, comercio electrónico, abastecimiento de la cadena de suministro, etc.) -- Aunque esta es una herramienta bastante habitual en las ciencias físicas y naturales aproximadamente hace tres décadas, ha sido utilizada recientemente en las cienci...

Methodology and Characteristics of Zad al-masir fi ‘ilm al-tafsirby AllamaIbn al-Jawzī (Urdu

Directory of Open Access Journals (Sweden)

Dr. Muhammad Riaz al Azhari

2017-01-01

Full Text Available This article describes the methodology and characteristics of Zad al-masir fi ‘ilm al-tafsir. This is one the finest work of AllamaIbn al-Jawzī, a 6th century prominent Interpreter. Several editions of this Tafsir have been published. However, the edition of dar al-kitab al-‘arbi, Beirut published in four volumes is selected for this study. This exegesis is based on conventional narrations, authentic quotations from the Islamic Scholars and lingual & grammatical discussions. As a witness, causes of verses (asbabal-Nuz┴l,Makki and MadaniSurah’s (chapters, the abrogating and abrogated verses (al-nasikhwal-mans┴kh and Islamic jurisprudence have been discussed in it where needed. The quality of this translation which is admirable is that mostly authentic Ahadith from original sources, and references to well known basic books in relevant discussions have been described. `

Phenotypic and genotypic studies of ALS cases in ALS-SMA families.

Science.gov (United States)

Corcia, Philippe; Vourc'h, Patrick; Blasco, Helene; Couratier, Philippe; Dangoumau, Audrey; Bellance, Remi; Desnuelle, Claude; Viader, Fausto; Pautot, Vivien; Millecamps, Stephanie; Bakkouche, Salah; Salachas, FranÇois; Andres, Christian R; Meininger, Vincent; Camu, William

2018-03-01

Amyotrophic lateral sclerosis (ALS) and spinal muscular atrophy (SMA) are the most frequent motor neuron disorders in adulthood and infancy, respectively. There is a growing literature supporting common pathophysiological patterns between those disorders. One important clinical issue for that is the co-occurrence of both diseases within a family. To collect families in which ALS and SMA patients co-exist and describe the phenotype and the genotype of ALS patients. Nine families with co-occurrence of SMA and ALS have been gathered over the last 15 years. Epidemiological, phenotype and genetic status were collected. Out of the nine families, six corresponded to the criteria of familial ALS (FALS). Clinical data were available for 11 patients out of the 15 ALS cases. Mean age of onset was 58.5 years, site of onset was lower limbs in nine cases (81.8%), median duration was 22 months. Four ALS patients carried a mutation: three mutations in SOD1 gene (G147N in two cases and one with E121G) and one repeat expansion in the C9ORF72 gene. Three patients had abnormal SMN1 copy numbers. While the high proportion of familial history of ALS cases in these ALS-SMA pedigrees could have suggested that these familial clusters of the two most frequent MND rely on a genetic background, we failed to exclude that this occurred by chance.

Hi-Plex for Simple, Accurate, and Cost-Effective Amplicon-based Targeted DNA Sequencing.

Science.gov (United States)

Pope, Bernard J; Hammet, Fleur; Nguyen-Dumont, Tu; Park, Daniel J

2018-01-01

Hi-Plex is a suite of methods to enable simple, accurate, and cost-effective highly multiplex PCR-based targeted sequencing (Nguyen-Dumont et al., Biotechniques 58:33-36, 2015). At its core is the principle of using gene-specific primers (GSPs) to "seed" (or target) the reaction and universal primers to "drive" the majority of the reaction. In this manner, effects on amplification efficiencies across the target amplicons can, to a large extent, be restricted to early seeding cycles. Product sizes are defined within a relatively narrow range to enable high-specificity size selection, replication uniformity across target sites (including in the context of fragmented input DNA such as that derived from fixed tumor specimens (Nguyen-Dumont et al., Biotechniques 55:69-74, 2013; Nguyen-Dumont et al., Anal Biochem 470:48-51, 2015), and application of high-specificity genetic variant calling algorithms (Pope et al., Source Code Biol Med 9:3, 2014; Park et al., BMC Bioinformatics 17:165, 2016). Hi-Plex offers a streamlined workflow that is suitable for testing large numbers of specimens without the need for automation.

Eutectic microstructures of Al-ThA13 and Al-UA14 alloys

International Nuclear Information System (INIS)

Vieira, R.R.; Ambrozio Filho, F.

1990-01-01

This paper deals on the microstructures of systems Al-ThAl3 and Al-UAL4, which are composed by a non faceted phase (aluminium) and an intermetallic phase (ThAl3 or UAL4) which is normally faceted phase. (C.M.)

Fabrication of a Porous Metal via Selective Phase Dissolution in Al-Cu Alloys

Directory of Open Access Journals (Sweden)

Juan Vargas-Martínez

2018-05-01

Full Text Available Through free corrosion, a new low cost porous material was successfully fabricated by removing a single phase of a binary aluminum-copper alloy. This selective phase dissolution was carried out an Al-Al2Cu eutectic alloy of the Al-Cu binary system and additionally for two hypereutectic compositions. The porosity of the material depends on the microstructure formed upon solidification. For this reason, several solidification methods were studied to define the most convenient in terms of uniformity and refinement of the average pore and ligament sizes. The samples were corroded in a 10% v/v NaOH aqueous solution, which demonstrated to be the most convenient in terms of time involved and resulting porosity conditions after the corrosion process. The porosity was measured through analysis of secondary electron images. The effectiveness of the process was verified using X-ray diffraction, which showed that, under the proposed methodology, there was complete removal of one of the phases, namely the aluminum one.

Interface reactions in the Al-Si-SiC and Mg-Al-Al{sub 2}O{sub 3} composite systems

Energy Technology Data Exchange (ETDEWEB)

Johnson, P.K. [Commission of the European Communities, Petten (Netherlands). Inst. for Advanced Materials; Fazal-Ur-Rehman [Imperial Coll. of Science, Technology and Medicine, London (United Kingdom). Dept. of Materials; Fox, S. [Imperial Coll. of Science, Technology and Medicine, London (United Kingdom). Dept. of Materials; Flower, H.M. [Imperial Coll. of Science, Technology and Medicine, London (United Kingdom). Dept. of Materials; West, D.R.F.

1995-12-31

Structural and compositional observations are reported on the influence of the interfaces on the mechanisms and kinetics of liquid metal-ceramic reactions in Al-SiC, Al-Si-SiC, Mg-Al{sub 2}O{sub 3} and Mg-Al-Al{sub 2}O{sub 3} composites. The aluminium based materials contained up to 20 vol% SiC in particulate form, and were produced by a spray casting process; subsequently the interface reactions were studied in samples heated to temperatures up to 1100 C. The reaction product was Al{sub 4}C{sub 3} in both Al-SiC and Al-Si-SiC composites. The influence of the crystallography and topology of the SiC particle surfaces on the nucleation of the Al{sub 4}C{sub 3} has been demonstrated; surface asperities play an important role. Growth of nuclei proceeds to form continuous reaction product layers which control the subsequent kinetics. The magnesium based composites contained 5 vol% Al{sub 2}O{sub 3} fibres (3 {mu}m in diameter), and were produced by a liquid infiltration process. SD Safimax fibres with relatively low and high porosity, and also RF Saffil fibres, with a silica binder, were investigated. Fibre porosity plays a major role in accelerating the penetration of Mg into the fibres with reaction to form MgO. Silica binder on the fibre surface transforms to MgO. The reaction rate was reduced by the presence of aluminium in the matrix. The factors controlling the reactions in the aluminium and magnesium based composites are compared. (orig.)

Inseguridad de ebastina: ¿interacción con barnidipino

Directory of Open Access Journals (Sweden)

Cremades J

2010-03-01

Full Text Available Mujer de 46 años que, en julio de 2007, refiere haber observado desde hace 3 meses “una disminución en el número de veces que orina al día”. Se le ofrece el servicio de seguimiento farmacoterapéutico, que acepta. La paciente está siendo tratada por una hipertensión arterial (HTA con Fortzaar® (losartan/hidroclorotiazida desde hace años y con Libradin® (barnidipino desde mayo de ese mismo año. También utiliza desde hace años Ebastel Forte Flas® (ebastina durante la primavera para tratar su alergia y Ventolín® inhalador (salbutamol para los brotes asmáticos en esa época. Por otro lado, emplea desde hace años Daflon® (diosmina/hesperidina para tratar un problema de “circulación”, Condrosan ® (condroitin sulfato para la artrosis, Optovite B12® (cianocobalamina y Acfol® (ácido fólico por una anemia perniciosa y Gelocatil 1g® (paracetamol, Nolotil® cápsulas (metamizol y Neobrufen® 600 (ibuprofeno para el dolor.

INVESTIGAR: LEER Y ESCRIBIR

Directory of Open Access Journals (Sweden)

Omar Parra Rozo

2007-01-01

Full Text Available La íntima relación que se establece entre la investigación, la lectura y la escritura determina las posibilidades de acercarse al mundo, de tratar de entenderlo, interpretarlo y proponer su transformación. El investigador busca afanosamente una explicación para los sucesos que lo rodean. El lector se detiene a palpar las figuras, a entender los artilugios del lenguaje y el escritor recrea el mundo. Estas interacciones se fundamentan en cuestionamientos elementales que parten del sencillo hecho de la observación y confluyen en la complejidad del juicio sobre deter- minadas situaciones. Se lee para tratar de entender, interpretar y transformar el contexto y se plasman las ideas sobre un pasado y un presente con el sueño de un cambio, de un mejoramiento individual y colectivo. Las preguntas dan apertura a nuevos interrogantes que se enmarcan en la posibilidad de leer, escribir e investigar para ser ordena- dos o definitivamente para sobrevivir, probablemente para ser felices, lo cual constituye el último horizonte del ser humano y su razón de vida.

KONSTRUKSI FIQH BUKHARI DALAM KITAB AL-JAMI’ AL-SHAHIH

Directory of Open Access Journals (Sweden)

Abdul Sattar

2011-06-01

Popularitas Imam Bukhari sebagai penyusun kitab Hadits memiliki posisi yang tinggi di kalangan masyarakat muslim. Kitab Al-Jami ‘al-Shahih karya Imam  Bukhari dianggap sebagai koleksi hadits terbaik setelah Quran. Namun, tidak ada banyak informasi tentang kemampuannya di bidang Hukum Islam (fiqh. Ada beberapa pertanyaan yang dapat diajukan dalam hal tersebut;  pertama, apakah pemikiran Imam Bukhari dipengaruh salah satu dari empat fuqaha Sunni saat menulis al-Jami ‘al-Shahih?. Kedua, apa yang diupayakan Imam Bukhari untuk mengartikulasikan pemikirannya tentang hukum Islam? Dengan menggunakan pendekatan eksploratif, verifikatif dan hermenetical, artikel ini akan mengungkapkan bahwa Imam Bukhari tidak berada di bawah pengaruh madhab tertentu dalam mengartikulasikan pemikirannya tentang hukum Islam. Dia mengartikulasikan pandangannya dengan cara yang unik dan execelent berdasarkan kapasitasnya sebagai muhaddits.

Eutectic Al-Si-Cu-Fe-Mn alloys with enhanced mechanical properties at room and elevated temperature

International Nuclear Information System (INIS)

Wang, E.R.; Hui, X.D.; Chen, G.L.

2011-01-01

Highlights: → Fabricated a kind of high performance Al-Si alloy with low production costs. → Clarified two different morphologies of α-Fe and corresponding crystal structures. → Analyzed the crystallography of Cu-rich phases before and after T6 treatment. → Fracture mechanism of precipitates in experimental alloys during tensile process. -- Abstract: In this paper, we report a novel kind of eutectic Al-Si-Cu-Fe-Mn alloy with ultimate tensile strength up to 336 MPa and 144.3 MPa at room temperature and 300 o C, respectively. This kind of alloy was prepared by metal mold casting followed by T6 treatment. The microstructure is composed of eutectic and primary Si, α-Fe, Al 2 Cu and α-Al phases. Iron-rich phases, which were identified as BCC type of α-Fe (Al 15 (Fe,Mn) 3 Si 2 ), exist in blocky and dendrite forms. Tiny blocky Al 2 Cu crystals disperse in α-Fe dendrites or at the grain boundaries of α-Al. During T6 treatment, Cu atoms aggregate from the super-saturation solid solution to form GP zones, θ'' or θ'. Further analysis found that the enhanced mechanical properties of the experimental alloy are mainly attributed to the formation of α-Fe and copper-rich phases.

La capitalización encubierta en la Reforma Tributaria de 2012: ¿trasplante legal o engendro legal?

Directory of Open Access Journals (Sweden)

José Manuel Castro Arango

2014-01-01

Full Text Available Colombia ha incorporado en el Estatuto Tributario (ET reglas contra la capitalización encubierta que se enmarcan dentro de las tendencias internacionales. No obstante, al tratar de “trasplantarlas” el Congreso ha descuidado los detalles y ha evadido la necesidad de “aclimatación” al contexto colombiano. Como resultado, hoy en día las sociedades, al financiar un proyecto, deberán considerar la cláusula general antielusión, las normas de precios de transferencia y la de subcapitalización. Estas tres normas pueden superponerse ante un mismo supuesto de hecho, creando complejas situaciones que son las que pretendemos poner de presente en este trabajo. Producto del tal análisis se concluye que la norma de subcapitalización ha sido un engendro legal que requiere ser interpretado como una presunción iuris tantum para poder adecuarse al principio constitucional de justicia tributaria y al de independencia (arm’s lenght previsto en los convenios para evitar la doble imposición (CDI.

La "historia de los omeyas de al-Andalus" en los Masalik al-Absar

OpenAIRE

Molina, Luis

2005-01-01

[ES]Los Masalik al-absar de Ibn Fadl Allah al-`Umari incluyen un breve resumen de la Historia de los omeyas de al-Andalus. En este trabajo se analizan las relaciones textuales entre ese pasaje y el Muqtabis de Ibn Hayyan, crónica que resulta ser la fuente casi única utilizada por al-`Umari para redactar ese capítulo. [EN]The Masalik al-absar by Ibn Fadl Allah al-`Umari contains a brief summary of the Umayyad history in al-Andalus. In this article, the textual relationship between this p...

IMPACTO DEL REVENUE MANAGEMENT EN LOS SISTEMAS DE CONTROL DE GESTIÓN

Directory of Open Access Journals (Sweden)

EMMA CASTELLÓ TALIANI

2016-01-01

Full Text Available El Revenue Management (RM tiene por objeto prever la demanda de productos o servicios de la manera más precisa posible, a fin de poder establecer y adaptar las decisiones de precio y disponi - bilidad de productos, en los diferentes canales de venta, y maximizar la rentabilidad. El RM trata de maximizar el ingreso que puede alcanzar una empresa con una capacidad fija de fabricación de un producto o de prestación de un servicio; así, el objetivo es tratar de destinar la capacidad a aquellos clientes que aportan más valor a la empresa, asignándoles la capacidad adecuada. En este marco de actuación se suele aludir, constantemente, a la necesidad de generar un resultado, o alcanzar una rentabilidad, sin embargo a estos efectos sólo se toman en consideración los costes variables, y en menor medida los costes fijos, lo que nos lleva a plantear la cuestión ¿qué impacto tiene el método de cálculo de costes en los procesos de gestión de ingresos? Esta es la cuestión que confor - ma el objetivo del presente artículo, al identificar cuáles son las interrelaciones que existen entre la contabilidad de gestión y el RM, dado que ambas perspectivas son complementarias en el logro de un objetivo común, como es buscar la mayor eficiencia y efectividad económica de las operaciones desarrolladas por cualquier empresa.

The effect of non-financial risk information on the evaluation of implied cost of capitals

OpenAIRE

Norio Kitagawa; Hyonok Kim; Masatoshi Goto

2011-01-01

The purpose of this paper is to examine the effect of voluntary disclosure of `business risk' information (hereafter referred to as `risk information' ), which is a significant determinant of the information environment, on estimating the cost of capital. Recently, some studies indicate that the reliability of the cost of capital estimation differs according to the accounting standards and the information environment of the firm (e.g. Chen et al., 2004; Easton and Monahan, 2005). On the basis...

Cryptanalysis of Lin et al.'s Efficient Block-Cipher-Based Hash Function

NARCIS (Netherlands)

Liu, Bozhong; Gong, Zheng; Chen, Xiaohong; Qiu, Weidong; Zheng, Dong

2010-01-01

Hash functions are widely used in authentication. In this paper, the security of Lin et al.'s efficient block-cipher-based hash function is reviewed. By using Joux's multicollisions and Kelsey et al.'s expandable message techniques, we find the scheme is vulnerable to collision, preimage and second

Impact of Foot Type on Cost of Lower Extremity Injury

Science.gov (United States)

2013-01-25

were at higher risk for injury. Additionally, researchers have found relationships between chronic heel pain and osteoarthritis of the knee and hip...Cost of Injury, in Physical Training and Sports Injury Prevention Guidelines . 2010, U.S. Army Public Health Command (Provisional). 11. Injury...study. BMC Musculoskelet Disord, 2007. 8: p. 41. 48. Reilly, K., et al., The role of foot and ankle assessment of patients with lower limb osteoarthritis

From Kitāb al-ḥadā’iq to Kitāb al-dawā’ir: Reconsidering Ibn al-Sīd al-Batalyawsī’s Philosophical Treatise

Directory of Open Access Journals (Sweden)

Eliyahu, Ayala

2015-06-01

Full Text Available The philosophical treatise known as Kitāb al-ḥadā’iq is generally ascribed to the 12th century Andalusian author Ibn al-Sīd al-Batalyawsī, although this attribution is sometimes contested. This paper offers a new interpretation of the title, textual history, authorship, sources, and literary genre of this treatise, on the basis of new textual evidence, a reexamination of known evidence, and a comparison between the treatise and Batalyawsī’s works. The conclusions of this study are first, that Kitāb al-ḥadā’iq was not the treatise’s original title, and therefore it should be renamed Kitāb al-dawā’ir; second, that Kitāb al-dawā’ir was originally part of (one of the versions of Batalyawsī’s Kitāb al-masā’il; and third, that the textual and stylistic similarities between this treatise and Batalyawsī’s other works prove the authenticity of the treatise’s attribution to Batalyawsī. In addition, new findings regarding Batalyawsī’s use of formulas from the Rasā’il Ikhwān al-Safā, in Kitāb al-dawā’ir and Kitāb al-masā’il provide further evidence for the deep impact of the Ikhwān on Batalyawsī’s thought, as well as for the close connection between Kitāb al-dawā’ir and Kitāb al-masā’il. This connection is further highlighted according to the attribution of both treatises to the genre of questions and answers in Arabic literature. The evidence gathered in this paper supports the claim that Batalyawsī’s Kitāb al-dawā’ir should be seen as an integral part of his literary oeuvre, as well as of Andalusian philosophical literature in general.Generalmente el tratado filosófico conocido como Kitāb al-ḥadā’iq se asocia al autor andalusí del siglo XII Ibn al-Sid al-Batalyawsī, aunque esta atribución ha sido discutida en ocasiones. Este artículo ofrece una nueva interpretación del título, la historia del texto, la autoría, las fuentes e incluso del género literario al que se

Theory and X-ray Absorption Spectroscopy for Aluminum Coordination Complexes – Al K-Edge Studies of Charge and Bonding in (BDI)Al, (BDI)AlR2, and (BDI)AlX2 Complexes.

Science.gov (United States)

Altman, Alison B; Pemmaraju, C D; Camp, Clément; Arnold, John; Minasian, Stefan G; Prendergast, David; Shuh, David K; Tyliszczak, Tolek

2015-08-19

Polarized aluminum K-edge X-ray absorption near edge structure (XANES) spectroscopy and first-principles calculations were used to probe electronic structure in a series of (BDI)Al, (BDI)AlX2, and (BDI)AlR2 coordination compounds (X = F, Cl, I; R = H, Me; BDI = 2,6-diisopropylphenyl-β-diketiminate). Spectral interpretations were guided by examination of the calculated transition energies and polarization-dependent oscillator strengths, which agreed well with the XANES spectroscopy measurements. Pre-edge features were assigned to transitions associated with the Al 3p orbitals involved in metal-ligand bonding. Qualitative trends in Al 1s core energy and valence orbital occupation were established through a systematic comparison of excited states derived from Al 3p orbitals with similar symmetries in a molecular orbital framework. These trends suggested that the higher transition energies observed for (BDI)AlX2 systems with more electronegative X(1-) ligands could be ascribed to a decrease in electron density around the aluminum atom, which causes an increase in the attractive potential of the Al nucleus and concomitant increase in the binding energy of the Al 1s core orbitals. For (BDI)Al and (BDI)AlH2 the experimental Al K-edge XANES spectra and spectra calculated using the eXcited electron and Core-Hole (XCH) approach had nearly identical energies for transitions to final state orbitals of similar composition and symmetry. These results implied that the charge distributions about the aluminum atoms in (BDI)Al and (BDI)AlH2 are similar relative to the (BDI)AlX2 and (BDI)AlMe2 compounds, despite having different formal oxidation states of +1 and +3, respectively. However, (BDI)Al was unique in that it exhibited a low-energy feature that was attributed to transitions into a low-lying p-orbital of b1 symmetry that is localized on Al and orthogonal to the (BDI)Al plane. The presence of this low-energy unoccupied molecular orbital on electron-rich (BDI)Al distinguishes

Implantación de una metodología cooperativa de cálculo de costes de los servicios públicos locales

Directory of Open Access Journals (Sweden)

Ander Ibarloza Arrizabalaga

2017-07-01

El éxito logrado con la metodología se debe a que se obtiene una información de gran valor con un esfuerzo controlado. Esta metodología de cálculo de costes persigue una aproximación eficiente al coste real del servicio que cubra las necesidades actuales de los gestores, más orientadas al cumplimiento normativo y al control del presupuesto que a la gestión de los servicios, tal y como se observa en el segundo contraste. Para aquellos gestores y servicios que necesiten un cálculo más depurado, la metodología propuesta permite un desarrollo ad hoc. Este nuevo escenario facilita una transferencia de conocimiento más receptiva y útil y favorece el acercamiento entre los ámbitos académico y profesional.

Conservation economics. Comment on "Using ecological thresholds to evaluate the costs and benefits of set-asides in a biodiversity hotspot".

Science.gov (United States)

Finney, Christopher

2015-02-13

Banks-Leite et al. (Reports, 29 August 2014, p. 1041) conclude that a large-scale program to restore the Brazilian Atlantic Forest using payments for environmental services (PES) is economically feasible. They do not analyze transaction costs, which are quantified infrequently and incompletely in the literature. Transaction costs can exceed 20% of total project costs and should be included in future research. Copyright © 2015, American Association for the Advancement of Science.

Thermodynamic properties of Al-Mn, Al-Cu, and Al-Fe-Cu melts and their relations to liquid and quasicrystal structure

International Nuclear Information System (INIS)

Zaitsev, A I; Zaitseva, N E; Shimko, R Yu; Arutyunyan, N A; Dunaev, S F; Kraposhin, V S; Lam, Ha Thanh

2008-01-01

Thermodynamic properties of molten Al-Mn, Al-Cu and Al-Fe-Cu alloys in a wide temperature range of 1123-1878 K and the whole range of concentrations have been studied using the integral effusion method and Knudsen mass spectrometry. Thermodynamic functions of melts were described by the associated solution model. The possibility of icosahedral quasicrystal (i-QC) precipitation from liquid Al-Mn and Al-Cu-Fe alloys was found to be a consequence of the existence in liquid associates (clusters). A geometric model is suggested for the structure of associates in liquid

Energy and environmental costs. An approach to the case of the automotive vehicles; Energia y costos ambientales: Una aproximacion al caso de los vehiculos automotores

Energy Technology Data Exchange (ETDEWEB)

Martinez Flores, Leonardo [Instituto Nacional de Ecologia (Mexico)

1996-07-01

The energy consumption of the Metropolitan Zone of the Valley of Mexico (ZMVM) is presented, considering the different economic sectors and the different types of fuels used by them. The form in which this demand will impact the air quality largely depends on the energy balance. Also an inventory of the emissions in 1989 is given. It is possible to emphasize that the power balance maintains a close association with the emissions inventory, which reflects the dependency of the emissions with respect to the energy use. Finally an analysis is made of the considered environmental costs for Mexico. [Spanish] Se presenta el consumo energetico de la zona metropolitana del valle de Mexico (ZMVM), considerando los distintos sectores economicos y los diferentes tipos de combustibles utilizados por ellos. La forma en que esta demanda impactara la calidad del aire depende en buena medida del balance energetico. Tambien se muestra un inventario de las emisiones en 1989. Cabe destacar que el balance energetico mantiene una asociacion estrecha con el inventario de emisiones, lo cual refleja la dependencia de las emisiones respecto al uso de energia. Finalmente se hace un analisis de los costos ambientales estimados para Mexico.

Sintering Behavior of CNT Reinforced Al6061 and Al2124 Nanocomposites

Directory of Open Access Journals (Sweden)

Nouari Saheb

2014-01-01

Full Text Available Ball milling and spark plasma sintering were successfully used to produce carbon nanotube reinforced Al6061 and Al2124 nanocomposites which have potential applications in the fields of aerospace, automotive, electronics, and high precision instrumentation. Al2124 and Al6061 nanocomposite powders containing 0.5 to 2 wt.% CNTs prepared through sonication and wet ball milling were spark plasma sintered at 400, 450, and 500°C for 20 minutes under a pressure of 35 MPa. CNTs were better dispersed, and less agglomerated and had good adhesion to the matrix in composites containing 1 wt.% CNTs. The increase of CNT content to 2 wt.% led to the formation of CNT clusters which resulted in less uniform and homogenous composite powders. Almost full densification of Al6061 reinforced with CNTs was achieved at 500°C. Also, CNTs reinforced Al2124 nanocomposites reached very high densities at 500°C. Composites reinforced with 1 wt.% CNTs displayed better densification compared to composites containing 2 wt.% CNTs. The increase of CNTs content from 0.5 to 1 wt.% increased the hardness of the Al6061 and Al2124 alloys to maximum values. Further increase of CNTs content to 2 wt.% decreased the hardness to values lower than that of the monolithic alloys.

Tetragonal phase in Al-rich region of U-Fe-Al system

International Nuclear Information System (INIS)

Meshi, L.; Zenou, V.; Ezersky, V.; Munitz, A.; Talianker, M.

2005-01-01

A new ternary aluminide U 2 FeAl 20 with the approximate composition Al-4.2at% Fe-8.5at% U was observed in the Al-rich corner of the U-Al-Fe system. Transmission electron microscopy and electron microdiffraction technique were used for characterization of the structure of this phase. It has a tetragonal unit cell with the parameters a=12.4A and c=10.3A and can be described by the space group I4-bar 2m

Ilhaq al-Masa'il bi Nazairiha dan Penerapannya dalam Bahth al-Masa'il

Directory of Open Access Journals (Sweden)

Luthfi Hadi Aminuddin

2013-11-01

Full Text Available Abstract: Ilh}a>q al-Masa>’il bi Naz}a>iriha is one of the methods used by Nahdlatul Ulama in resisting the opinion based on (manhaji analytical concept of Islamic jurisprudence (the solution for complex social problems as the main purpose of Islamic shari’ah. As known that, up to now, ilh}a>q has been understood as a process of answering a new case by the way of equating to the old one which is written in the book called al-mu’tabarah. Such ilh}a>q has got many criticisms both from the definitions, procedures and its epistemogical footing. This paper is about to reveal how the NU clerics of Islam understand the concept of Ilh}a>q}, what its epistemological footing was and how the concept was applied in discussing many cases (bah}th al-masa>’il. Based on the writer’s study to several documents of decision results of NU that Ilh}a>q did not only simplify to equate the new cases with the old ones that have been freely discussed in the books of al-mu’tabarah, but both cases should have similar legal substance, that is, both should be under the decrees of laws of al-qawa> ‘id al-fiqhi>yah. Thus, Ilh}a>q is actually answering the problem by applying al-qawa>‘id al-fiqhi>yah, whereas the formulation al-qawa>‘id al-fiqhi>yah itself was set off from the examination of a number of furu>’ generated by qiya> s. This paper also found three variations of the implementation of Ilh}a>q in bah}th al-masa>’il. First, the application of Ilh}a>q was without mentioning al-qawa> ‘id al-fiqhi>yah which covered new cases (mulh}aq and the old case law that has been known in the books of fiqh (mulh}aq bih/attached to. Second, the application of Ilh}a>q was accompanied by mentioning mulh}aq bih and al-qawa> ‘id al-fiqhi>yah. Third, the application of Ilh}a>q, was only by the mentioning al-qawa> ‘id al-fiqhi>yah.

Bioenergy costs and potentials with special attention to implications for the land system

Science.gov (United States)

Popp, A.; Lotze-Campen, H.; Dietrich, J.; Klein, D.; Bauer, N.; Krause, M.; Beringer, T.; Gerten, D.

2011-12-01

In the coming decades, an increasing competition for global land and water resources can be expected, due to rising demand for agricultural products, goals of nature conservation, and changing production conditions due to climate change. Especially biomass from cellulosic bioenergy crops, such as Miscanthus or poplar, is being proposed to play a substantial role in future energy systems if climate policy aims at stabilizing greenhouse gas (GHG) concentration at low levels. However, the potential of bioenergy for climate change mitigation remains unclear due to large uncertainties about future agricultural yield improvements, land availability for biomass plantations, and implications for the land system. In order to explore the cost-effective contribution of bioenergy to a low carbon transition with special attention to implications for the land system, we present a modeling framework with detailed biophysical and economic representation of the land and energy sector: We have linked the global dynamic vegetation and water balance model LPJmL (Bondeau et al. 2007, Rost et al. 2008), the global land and water use model MAgPIE (Lotze-Campen et al. 2008, Popp et al. 2010), and the global energy-economy-climate model ReMIND (Leimbach et al. 2009). In this modeling framework LPJmL supplies spatially explicit (0.5° resolution) agricultural yields as well as carbon and water stocks and fluxes. Based on this biophysical input MAgPIE delivers cost-optimized land use patterns (0.5° resolution), associated GHG emissions and rates of future yield increases in agricultural production. Moreover, shadow prices are calculated for irrigation water (as an indicator for water scarcity), food commodities, and bioenergy (as an indicator for changes in production costs) under different land use constraints such as forest conservation for climate change mitigation and as a contribution to biodiversity conservation. The energy-economy-climate model ReMIND generates the demand for

Nanoindentation studies of ex situ AlN/Al metal matrix nanocomposites

International Nuclear Information System (INIS)

Fale, Sandeep; Likhite, Ajay; Bhatt, Jatin

2014-01-01

Highlights: • Formation of in-situ phases nucleated on AlN particles strengthens the matrix. • Formation of in-situ phases increases with AlN content in nanocomposites. • Stronger in-situ phases results in increased hardness and modulus of elasticity. - Abstract: Nanocrystalline Aluminium nitride (AlN) powder is dispersed in different weight ratio in Aluminum matrix to fabricate metal matrix nanocomposite (MMNC) using ex situ melt metallurgy process. The synthesized Al–AlN nanocomposites are studied for phase analysis using high resolution scanning electron microscopy (FEG-SEM) and for hardness behavior using microindentation and nanoindentation tests. Quantitative analysis of the oxide phases is calculated from thermodynamic data and mass balance equation using elemental data obtained from energy dispersive spectroscopy (EDS) results. Role of oxide phases in association with AlN particles is investigated to understand the mechanical behavior of composites using nanoindentation tester. Load–displacement profile obtained from nanoindentation test reveals distribution of oxide phases along with AlN particle and their effect on indent penetration

Estudio del coste-beneficio de un programa de seguimiento a pacientes con riesgo cardiovascular

Directory of Open Access Journals (Sweden)

Vilanova L,

2012-09-01

Full Text Available INTRODUCCIÓN El farmacéutico tiene que demostrar que es capaz de realizar e implementar unos servicios de calidad y su eficiencia antes de poder exigir la financiación de estos servicios. El objetivo general del presente estudio es analizar los costes derivados de la prestación de un servicio de seguimiento para pacientes con enfermedad cardiovascular y evaluar la posible eficiencia en el mismo. MATERIAL Y MÉTODOS Para la recogida y análisis de datos se utilizó el programa Cuídate Corazón® (Laboratorios Lácer y para establecer un posible precio al servicio se aplicó la estrategia de Kotler, utilizando el método orientado al coste. Como evaluación de la efectividad del servicio se contabilizaron los RNM detectados al paciente y la aceptación por parte del médico de la intervención del farmacéutico. Se realizó una encuesta para ver el grado de satisfacción del paciente. RESULTADOS El coste por paciente y mes del servicio para cada farmacia resultó ser de 2,48 . Se detectaron 10 RNM de los que en un 78% la intervención farmacéutica fue aceptada por el médico, que hizo cambios en la medicación. El paciente resulta estar muy satisfecho por este servicio, que mejora su percepción del farmacéutico como profesional sanitario y cree que el farmacéutico debe ser remunerado por el servicio. DISCUSIÓN Se considera que se ha generado un valor añadido a la atención del paciente, creando una demanda del servicio prestado. Las farmacias participantes seguirán trabajando con el programa Cuídate Corazón ®, y establecerán una remuneración para el farmacéutico por parte del paciente, ya que se considera que esto responsabiliza al profesional y mejora la implicación del paciente en beneficio de su salud

An approach using Lagrangian/surrogate relaxation for lot-sizing with transportation costs

Directory of Open Access Journals (Sweden)

Flavio Molina

2009-08-01

Full Text Available The aim of this work was to study a distribution and lot-sizing problem that considers costs with transportation to a company warehouse as well as, inventory, production and setup costs. The logistic costs are associated with necessary containers to pack produced items. The company negotiates a long-term contract in which a fixed cost per period is associated with the transportation of the items. On the other hand, a limited number of containers are available with a lower cost than the average cost. If an occasional demand increase occurs, other containers can be utilized; however, their costs are higher. A mathematical model was proposed in the literature and solved using the Lagrangian heuristic. Here, the use of the Lagrangian/surrogate heuristic to solve the problem is evaluated. Moreover, an extension of the literature model is considered adding capacity constraints and allowing backlogging. Computational tests show that Lagrangian/surrogate heuristics are competitive, especially when the capacity constraints are tight.Neste trabalho estuda-se um problema de dimensionamento de lotes e distribuição que envolve além de custos de estoques, produção e preparação, custos de transportes para o armazém da empresa. Os custos logísticos estão associados aos contêineres necessários para empacotar os produtos produzidos. A empresa negocia um contrato de longo prazo onde um custo fixo por período é associado ao transporte dos itens, em contrapartida um limite de contêineres é disponibilizado com custo mais baixo que o custo padrão. Caso ocorra um aumento ocasional de demanda, novos contêineres podem ser utilizados, no entanto, seu custo é mais elevado. Um modelo matemático foi proposto na literatura e resolvido utilizando uma heurística Lagrangiana. No presente trabalho a resolução do problema por uma heurística Lagrangiana/surrogate é avaliada. Além disso, é considerada uma extensão do modelo da literatura adicionando

Relación coste-beneficio de las políticas sobre consumo de tabaco en el lugar de trabajo

Directory of Open Access Journals (Sweden)

Raaijmakers Tamara

2003-01-01

Full Text Available Este trabajo revisa los motivos que llevan a las empresas a establecer una política sobre control del tabaquismo, los beneficios económicos para la sociedad que se derivan de su adopción, y sus costes, detallados por países en la Unión Europea. Se revisa también la literatura sobre los costes de la aplicación de una política sobre tabaquismo en el ámbito laboral. El principal objetivo de las políticas sobre tabaquismo en el lugar de trabajo es la protección de los empleados del aire contaminado por el humo de tabaco (ACHT. Otros motivos son la reducción de costes; la mejora de la imagen; y la disminución de absentismo, accidentes laborales, conflictos y costes adicionales debidos al tabaco. La protección frente al ACHT no supone mayores costes para la empresa, y se refieren ventajas económicas con su puesta en práctica. Los beneficios sobrepasan con creces las inversiones, en particular a largo plazo, y parecen mayores cuando se establece una prohibición total de fumar en el lugar de trabajo en vez de áreas para fumadores.

Isothermal cross-sections of Sr-Al-Ge and Ba-Al-Ge systems at 673 K

International Nuclear Information System (INIS)

Kutsenok, N.L.; Yanson, T.I.

1987-01-01

X-ray and microstructural analyses are used to study phase equilibria in Sr-Al-Ge and Ba-Al-Ge systems. Existence of SrAl 2 Ge 2 , Sr(Al, Ge) 2 Ba(Al, Ge) 2 , Sr 3 Al 2 Ge 2 , Ba 3 Al 2 Ge 2 ternary compounds is confirmed, a new BaGe 4 binary compound and also new ternary compounds of approximate composition Sr 57 Al 30 Ge 13 and Ba 20 Al 40 Ge 40 , which crystal structure is unknown, are detected. Aluminium solubility in SrAl 4 and BaAl 4 binary compounds (0.05 atomic fraction) is determined. Ba(Al, Ge) 2 compound homogeneity region is defined more exactly (aluminium content varies from 0.27 to 0.51 at. fractions)

Production of 26Al by spallation of Fe, Si, Al nuclei

International Nuclear Information System (INIS)

Paillard, P.

1977-01-01

Cross sections for 7 Be, 10 Be and 26 Al formation in Al, Si and Fe targets bombarded with 0.6 and 24GeV protons have been measured by using highly selective chemical separation and low level background counters. Results for 26 Al at 0.6GeV are in mb: 17.9 + or - 2.7 in Al, 12.5 + or - 2.5 in Si and 0.45 + or - 0.14 in Fe; at 24GeV 2.6 + or - 0.5mb in Fe. Results for 10 Be are not valid on account of experimental difficulties. It is deduced from these values of aluminium in cosmic ray propagation that 26 Al is not yet cosmic ray chronometer [fr

HUMEDAD CRÍTICA Y REPELENCIA AL AGUA EN ANDISOLES COLOMBIANOS BAJO COBERTURA DE Pinus patula Schltdl y Cham CRITICAL MOISTURE AND WATER REPELLENCY OF COLOMBIAN ANDISOLS COVERED WITH Pinus patula Schltdl and Cham

Directory of Open Access Journals (Sweden)

Daniel Francisco Jaramillo Jaramillo

2005-12-01

Full Text Available En un lote con Andisoles bajo cobertura de Pinus patula Schltdl y Cham se ubicaron 4 transectos sobre los cuales se hizo un muestreo horizontal cada 5 cm, en 4 profundidades, con el fin de establecer si había una zona de transición de humedad crítica en el suelo que estuviera controlando la presencia de repelencia al agua en él. Se hicieron determinaciones de WDPT en el campo y luego en muestras secadas a 35 °C, en laboratorio. En cada condición se determinó el contenido gravimétrico de humedad a cada muestra y se relacionaron estos contenidos con su correspondiente WDPT. Los suelos presentaron altos contenidos de humedad, tanto en campo, como secos a 35 °C. La mayoría de los sitios fueron humectables en campo pero, al secar las muestras a 35 °C, la mayoría de ellas, en las tres primeras profundidades, se tornaron fuertemente repelentes al agua. Ambas propiedades tuvieron una alta variabilidad. En algunas profundidades de varios transectos fue posible definir, precariamente, zonas críticas de humedad para la repelencia al agua pero, al tratar de generalizar esta zona para todo el perfil del transecto, no fue posible definirla.In a stand with Andisoles planted with Pinus patula Schltdl and Cham, 4 transects were established for horizontal sampling every 5 cm in 4 depths to establish whether there was a transition zone for critical humidity in the soil that could determine the presence of water repellency in it. Determinations of WDPT were made in the field and later on samples dried at 35 °C in the laboratory. For each condition, the gravimetric content of humidity of each sample was determined and these contents were compared to their corresponding WDPT. The soils presented high humidity contents, both in the field and when dried at 35 °C. Most of the sites were humidified in the field, but upon drying the samples at 35 °C, the majority of them from the first three pit depths became strongly water repellent. Both properties were

143 - 148_Makeri et al.

African Journals Online (AJOL)

USER

2015-06-01

Jun 1, 2015 ... Yuan et al., 2003), antimicrobial activity (Sundarrao et al., 1993; Betancur-Galvis et al., 1999; Takashi et al., 2006), anti-parasitic, anti-malarial activities (Alali et al., 1998; Jaramillo et al., 2000; Luna et al.,. 2005). This study evaluates the antibacterial activity of extract of stem –bark and leaf extracts of Annona.

Phase relationships in the Al-rich region of the Al-Cu-Er system

International Nuclear Information System (INIS)

Zhang Ligang; Masset, Patrick J.; Cao Fuyong; Meng Fangui; Liu Libin; Jin Zhanpeng

2011-01-01

Research highlights: → One ternary phase τ 1 -Al 8 Cu 4 Er in Al-rich region with a composition of 59.4-60.4 at.% Al, 32.2-33.8 at.% Cu, and 6.4-7.7 at.% Er is observed in both as-cast and annealed alloys. At 673 K, the binary Al 3 Er phase dissolves about 3.51 at.% Cu. → The calculated solidification paths (based on the CALPHAD method) of as-cast alloys are in agreement with the experimental results. → It can be found that the resultant thermodynamic database can be applied to case studies of as-cast alloys, showing that the literature thermodynamic description of the Al-Cu-Er system is reliable as a working basis for computer-assisted alloy design. - Abstract: The Al-rich region of the ternary Al-Cu-Er system is investigated using the method of X-ray diffraction, scanning electron microscopy with energy dispersive X-ray spectroscopy. Phase equilibria in the Al-rich region of the Al-Cu-Er system at 673 K have been obtained, and the microstructures of as-cast alloys in the Al-rich region are also investigated. One ternary phase τ 1 -Al 8 Cu 4 Er with a composition of 59.4-60.4 at.% Al, 32.2-33.8 at.% Cu, and 6.4-7.7 at.% Er is observed in both as-cast and annealed alloys. At 673 K, the binary Al 3 Er phase dissolves about 3.51 at.% Cu. The calculated solidification paths (based on the CALPHAD method) of as-cast alloys are in agreement with the experimental results.

High mobility AlGaN/GaN heterostructures grown on Si substrates using a large lattice-mismatch induced stress control technology

International Nuclear Information System (INIS)

Cheng, Jianpeng; Yang, Xuelin; Sang, Ling; Guo, Lei; Hu, Anqi; Xu, Fujun; Tang, Ning; Wang, Xinqiang; Shen, Bo

2015-01-01

A large lattice-mismatch induced stress control technology with a low Al content AlGaN layer has been used to grow high quality GaN layers on 4-in. Si substrates. The use of this technology allows for high mobility AlGaN/GaN heterostructures with electron mobility of 2040 cm 2 /(V·s) at sheet charge density of 8.4 × 10 12  cm −2 . Strain relaxation and dislocation evolution mechanisms have been investigated. It is demonstrated that the large lattice mismatch between the low Al content AlGaN layer and AlN buffer layer could effectively promote the edge dislocation inclination with relatively large bend angles and therefore significantly reduce the dislocation density in the GaN epilayer. Our results show a great potential for fabrication of low-cost and high performance GaN-on-Si power devices

Microstructure and Mechanical Properties of Ti-6Al-4V Fabricated by Selective Laser Melting of Powder Produced by Granulation-Sintering-Deoxygenation Method

Science.gov (United States)

Sun, Pei; Fang, Z. Zak; Zhang, Ying; Xia, Yang

2017-12-01

Commercial spherical Ti powders for additive manufacturing applications are produced today by melt-atomization methods at relatively high costs. A meltless production method, called granulation-sintering-deoxygenation (GSD), was developed recently to produce spherical Ti alloy powder at a significantly reduced cost. In this new process, fine hydrogenated Ti particles are agglomerated to form spherical granules, which are then sintered to dense spherical particles. After sintering, the solid fully dense spherical Ti alloy particles are deoxygenated using novel low-temperature deoxygenation processes with either Mg or Ca. This technical communication presents results of 3D printing using GSD powder and the selective laser melting (SLM) technique. The results showed that tensile properties of parts fabricated from spherical GSD Ti-6Al-4V powder by SLM are comparable with typical mill-annealed Ti-6Al-4V. The characteristics of 3D printed Ti-6Al-4V from GSD powder are also compared with that of commercial materials.

Mechanical properties and deformation behavior of Al/Al7075, two-phase material

International Nuclear Information System (INIS)

Sherafat, Z.; Paydar, M.H.; Ebrahimi, R.; Sohrabi, S.

2010-01-01

In the present study, mechanical properties and deformation behavior of Al/Al7075, two-phase material were investigated. The two-phase materials were fabricated by mixing commercially pure Al powder with Al7075 chips and consolidating the mixture through hot extrusion process at 500 o C. Mechanical properties and deformation behavior of the fabricated samples were evaluated using tensile and compression tests. A scanning electron microscope was used to study the fracture surface of the samples including different amount of Al powder, after they were fractured in tensile test. The results of the tensile and compression tests showed that with decreasing the amount of Al powder, the strength increases and ductility decreases. Calculation of work hardening exponent (n) indicated that deformation behavior does not follow a regular trend. In a way that the n value was approved to be variable and a strong function of strain and Al powder wt% of the sample. The results of the fractography studies indicate that the type of fracture happened changes from completely ductile to nearly brittle by decreasing the wt% of Al powder from 90% to 40%.

Fabrication and characterization of CuAlO2 transparent thin films prepared by spray technique

International Nuclear Information System (INIS)

Bouzidi, C.; Bouzouita, H.; Timoumi, A.; Rezig, B.

2005-01-01

CuAlO 2 thin films have been grown on glass substrates using spray technique; a low-cost method of thin films depositing. The deposition was carried out in a 450-525 deg. C range of substrate temperature. The solution and gas flow rates were kept constant at 5 cm 3 min -1 and 6.10 -3 m 3 min -1 , respectively. Compressed air was used as a carrier gas. The structural, morphological and optical properties of these thin films have been studied. These properties are strongly related to the substrate temperature and to the [Cu]/[Al] molar ratio r. X-ray diffraction analysis confirmed the initial amorphous nature of as-deposited films and phase transition into crystalline CuAlO 2 with the preferential orientation (1 0 1) upon annealing at 570 deg. C. The optical transmission of 80% has been achieved in the visible spectrum. CuAlO 2 band gap energy in the range of 3.34-3.87 eV has been found by optical measurement depending on fabrication parameters

A Scholar from Saray: Mawlana Zada al-Sarayi (754/1353–791/1389 in the Biographical Dictionary of Taqi al-Din al-Maqrizi (766/1365–845/1441 “Kitab al-Muqaffa al-Kabir” (The Great Rhymed Book

Directory of Open Access Journals (Sweden)

D.R. Zaynuddinov

2017-03-01

Full Text Available Research objective: to introduce into academic circulation previously unknown source on the Golden Horde history. Research materials: biographical dictionary of Taqi al-Din al-Maqrizi (766/1365 – 845/1441 “Kitab al-Muqaffa al-Kabir” (The Great Rhymed Book. Results and novelty of the research: This article contains materials from the works of historians engaged in the narrative biography, which V.G. Tiesenhausen did not include in his “Collection of Materials on the Golden Horde history (extract from Arab writings”, although their writings contain very valuable information about the Golden Horde History. Research novelty consists in the fact that the author of this article presents one paragraph from biographical dictionary of Taqi al-Din al-Maqrizi, whose article number 421 provides information about a scholar from Saray – Mawlana Zada al-Sarayi. The author provides its translation and commentary referring to the more than ten medieval Arab sources. After receiving basic education at home, Mawlana Zada al-Sarayi traveled to many Eastern countries in search of knowledge and after having received high recognition he settled in Cairo as a teacher of Sharia Sciences. Despite the fact that his life was interrupted at an early age (36 years, he left a deep mark in science. His son Muhibbu al-Din (Cairo, 791/1389 – Mecca, Friday, the 3rd of Dhu al-Hijjah 859/13 November 1455 also became a great scholar as well as an imam of Sultan al-Ashraf Barsbay himself and other sultans after him. Nisba al-Sarayi sounded on the lips of the Ulema of the East as a symbol of learnedness and high temper. As a result of research it must be said that the study of life of Mawlana Zada al-Sarayi (754/1353 – 791/1389 and the number of migrants from Desht-i Kipchak in Egypt will help researchers in a deeper and more detailed study of the Golden Horde history.

Improved AlGaN/GaN HEMTs Grown on Si Substrates Using Stacked AlGaN/AlN Interlayer by MOCVD

International Nuclear Information System (INIS)

Wang Yong; Yu Nai-Sen; Li Ming; Lau Kei-May

2011-01-01

AlGaN/GaN high electron mobility transistors (HEMTs) are grown on 2-inch Si (111) substrates by MOCVD. The stacked AlGaN/AlN interlayer with different AlGaN thickness and indium surfactant doped is designed and optimized to relieve the tensile stress during GaN epitaxial growth. The top 1.0μm GaN buffer layer grown on the optimized AlGaN/AlN interlayer shows a crack-free and shining surface. The XRD results show that GaN(002) FWHM is 480 arcsec and GaN(102) FWHM is 900 arcsec. The AGaN/GaN HEMTs with optimized and non-optimized AlGaN/AlN interlayer are grown and processed for comparison and the dc and rf characteristics are characterized. For the dc characteristics of the device with optimized AlGaN/AlN interlayer, maximum drain current density I dss of 737mA/mm, peak transconductance G m of 185mS/mm, drain leakage current density I ds of 1.7μA/mm, gate leakage current density I gs of 24.8 μA/mm and off-state breakdown voltage V BR of 67 V are achieved with L g /W g /L gs /L gd = 1/10/1/1 μm. For the small signal rf characteristics of the device with optimized AlGaN/AlN interlayer, current gain cutoff frequency f T of 8.3 GHz and power gain cutoff frequency f max of 19.9 GHz are achieved with L g /W g /L gs /L gd = 1/100/1/1 μm. Furthermore, the best rf performance with f T of 14.5 GHz and f max of 37.3 GHz is achieved with a reduced gate length of 0.7μm. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Fitting of full Cobb-Douglas and full VRTS cost frontiers by solving goal programming problem

Science.gov (United States)

Venkateswarlu, B.; Mahaboob, B.; Subbarami Reddy, C.; Madhusudhana Rao, B.

2017-11-01

The present research article first defines two popular production functions viz, Cobb-Douglas and VRTS production frontiers and their dual cost functions and then derives their cost limited maximal outputs. This paper tells us that the cost limited maximal output is cost efficient. Here the one side goal programming problem is proposed by which the full Cobb-Douglas cost frontier, full VRTS frontier can be fitted. This paper includes the framing of goal programming by which stochastic cost frontier and stochastic VRTS frontiers are fitted. Hasan et al. [1] used a parameter approach Stochastic Frontier Approach (SFA) to examine the technical efficiency of the Malaysian domestic banks listed in the Kuala Lumpur stock Exchange (KLSE) market over the period 2005-2010. AshkanHassani [2] exposed Cobb-Douglas Production Functions application in construction schedule crashing and project risk analysis related to the duration of construction projects. Nan Jiang [3] applied Stochastic Frontier analysis to a panel of New Zealand dairy forms in 1998/99-2006/2007.

The cost implementation of adoption of e-commerce in SMES

Institute of Scientific and Technical Information of China (English)

朱书阳

2009-01-01

@@ 1.Introduction SMES are generally cnnsidered to be flexible to adapt to e-commerce.They are considered to be.a major component of all economies and are generally considered to be flexible,adaptive and innovative organizations(Rao et al,2003).E-commerce is introdueed to SMES and has a rapid growth of adoption.The open structure and low cost of using Internet provide a chance to communicate and collecting information conveniently to buyers and sellers.

Konsepsi Ibnu Jarir Al-Tabari Tentang Al-Qur’an, Tafsir Dan Ta’wil

Directory of Open Access Journals (Sweden)

A.M Ismatulloh

2012-12-01

Full Text Available The objective of this research is to describe the concept of Ibnu Jarir al-Tabari about al-Qur’an, tafsir and ta’wil. Ibn Jarir al-Tabari is an outstanding expert in the classic Islamic tradition. His knowledge in hadits, fiqh, lughah, history, and tafseer is unquestionable. This study uses an analytical descriptive design. The findings show that: Firstly, in defining al-Qur’an, al-Tabari focused on the al-Qur’an as an Arabic language text, not in other language. Secondly, al-Qur’an is written in sab’ah ahruf. It means that there are 7 different kinds of language with the same meaning. Thirdly, al-Qur’an comes from seven heaven’s door. Fourthly, there is no different word between tafseer and ta’wil. They have same meaning. These concepts are different to other concepts proposed by other ulama.

Cost-effectiveness of Different Advanced Life Support Providers for Victims of Out-of-hospital Cardiac Arrests

Directory of Open Access Journals (Sweden)

Zui-Shen Yen

2006-01-01

Conclusion: The use of EMTs as ALS care providers for OHCA patients in the two-tiered EMS system resulted in a reasonable cost-effectiveness ratio. EMTs could be considered as the second tier of EMS systems in urban areas in Taiwan.

Bridge approach slabs for Missouri DOT field evaluation of alternative and cost efficient bridge approach slabs.

Science.gov (United States)

2013-05-01

Based on a recent study on cost efficient alternative bridge approach slab (BAS) designs (Thiagarajan et : al. 2010) has recommended three new BAS designs for possible implementation by MoDOT namely a) 20 feet cast-inplace : slab with sleeper slab (C...

Towards the carbon fibers in the building industry

Directory of Open Access Journals (Sweden)

Miravete, A.

2001-12-01

Full Text Available There are two mainstreams in the building industry in the area of carbon fibers: rehabilitation and use as building material. The using of carbon fiber as a building material is taking place slower than as rehab system due to the very low cost of traditional building materials, the limitations of composite structure manufacturing processes and the conservative building regulations concerning materials in all the industrialized countries. However, these three issues are being solved in a very efficient way, as we will see along the coming paragraphs of this paper. This paper is split in two parts, first the carbon fiber as a material system, its typologies, manufacturing processes and industrial presentations will be described. Second, rehab and building applications will be analyzed.

En el área de fibra de carbono en la construcción hay actualmente dos líneas de trabajo: reparaciones e implantación en obra: La implantación en la obra civil está avanzando más despacio que la utilización en reparaciones debido al bajo coste de los materiales tradicionales, a la limitación de procesos de fabricación de estructuras de materiales compuestos y al conservadurismo de las normativas de edificación y obra civil en todos los países industrializados. Sin embargo, los tres asuntos mencionados están siendo abordados con eficiencia, como se explicará más adelante. En el presente artículo, se va a describir, el primer lugar, la fibra de carbono, sus tipos, procesos de fabricación y presentaciones industriales. En segundo lugar se tratarán las aplicaciones en la construcción, haciendo énfasis en las reparaciones y en la implantación en obra civil.

A low cost, disposable cable-shaped Al-air battery for portable biosensors

Science.gov (United States)

Fotouhi, Gareth; Ogier, Caleb; Kim, Jong-Hoon; Kim, Sooyeun; Cao, Guozhong; Shen, Amy Q.; Kramlich, John; Chung, Jae-Hyun

2016-05-01

A disposable cable-shaped flexible battery is presented using a simple, low cost manufacturing process. The working principle of an aluminum-air galvanic cell is used for the cable-shaped battery to power portable and point-of-care medical devices. The battery is catalyzed with a carbon nanotube (CNT)-paper matrix. A scalable manufacturing process using a lathe is developed to wrap a paper layer and a CNT-paper matrix on an aluminum wire. The matrix is then wrapped with a silver-plated copper wire to form the battery cell. The battery is activated through absorption of electrolytes including phosphate-buffered saline, NaOH, urine, saliva, and blood into the CNT-paper matrix. The maximum electric power using a 10 mm-long battery cell is over 1.5 mW. As a demonstration, an LED is powered using two groups of four batteries in parallel connected in series. Considering the material composition and the cable-shaped configuration, the battery is fully disposable, flexible, and potentially compatible with portable biosensors through activation by either reagents or biological fluids.

Crear materiales a medida: una propuesta desde la escritura

Directory of Open Access Journals (Sweden)

María Martínez Casas

2014-09-01

Full Text Available El presente artículo tiene como objetivo exponer cómo y por qué usar los textos redactados por alumnos para diseñar actividades didácticas de E/LE. Para ello se esbozarán en primer lugar los principios cognitivos que subyacen al proceso de expresión escrita y que deben contemplarse al diseñar materiales. En segundo lugar se ofrecerán ejemplos prácticos de actividades creadas íntegramente a partir de redacciones de universitarios alemanes para la práctica de competencias lingüísticas (gramática yléxico. Para concluir se indagarán las posibilidades de tratar contenidos comunicativos y culturales en los materiales creados a partir de las redacciones de alumnos.

Ramon Margalef, de lo posible y lo razonable

Directory of Open Access Journals (Sweden)

Joshua Beneite Martí

2017-05-01

Full Text Available El científico que se presenta aquí ha realizado contribuciones muy significativas al desarrollo de la teoría ecológica a nivel internacional. Pero su pensamiento descansa, por un lado, sobre un evidente cañamazo filosófico y, por otro, se extiende hasta alcanzar campos como la política y la ética. Se tratará, pues, de señalar tanto su itinerario al través de la filosofía natural, como de la medida en que su legado afecta a cuestiones ambientales muy discutidas en distintos ámbitos. Para la conclusión, se confrontan sus propuestas con algunas corrientes ‘intervencionistas’ que despuntan en el actual paraguas de la ética ecológica.

Transaction costs of unilateral CDM projects in India-results from an empirical survey

International Nuclear Information System (INIS)

Krey, Matthias

2005-01-01

Recently, transaction costs in the context of the Clean Development Mechanism (CDM) gained considerable attention as they were generally perceived to be significantly higher than for the other Kyoto Mechanisms. However, empirical evidence on the amount of transaction costs of CDM projects is very scarce. This paper presents the results from an empirical survey designed to quantify transaction costs of potential non-sink CDM projects in India. The definition of transaction costs of CDM projects was derived from recent literature and observations made in the current market for Certified Emission Reductions (CERs). During the survey, parts of transaction costs of 15 projects were quantified. An assessment of the results showed that specific transaction costs depend, to a large extent, on economies of scale in terms of total amount of CERs generated over the crediting period. Total transaction costs were quantified for seven projects. The costs range from 0.07 to 0.47 dollar/t CO 2 . As the projects have an emission reduction between 0.24 Mt CO 2 and 5.00 Mt CO 2 over the crediting period, the results support the assumption of Michaelowa et al. (Climate Policy 3 (2003) 273) that projects with emission reductions smaller than 0.20 Mt CO 2 are not economically viable at current CER prices

Costs and cost-effectiveness of periviable care.

Science.gov (United States)

Caughey, Aaron B; Burchfield, David J

2014-02-01

With increasing concerns regarding rapidly expanding healthcare costs, cost-effectiveness analysis allows assessment of whether marginal gains from new technology are worth the increased costs. Particular methodologic issues related to cost and cost-effectiveness analysis in the area of neonatal and periviable care include how costs are estimated, such as the use of charges and whether long-term costs are included; the challenges of measuring utilities; and whether to use a maternal, neonatal, or dual perspective in such analyses. A number of studies over the past three decades have examined the costs and the cost-effectiveness of neonatal and periviable care. Broadly, while neonatal care is costly, it is also cost effective as it produces both life-years and quality-adjusted life-years (QALYs). However, as the gestational age of the neonate decreases, the costs increase and the cost-effectiveness threshold is harder to achieve. In the periviable range of gestational age (22-24 weeks of gestation), whether the care is cost effective is questionable and is dependent on the perspective. Understanding the methodology and salient issues of cost-effectiveness analysis is critical for researchers, editors, and clinicians to accurately interpret results of the growing body of cost-effectiveness studies related to the care of periviable pregnancies and neonates. Copyright © 2014 Elsevier Inc. All rights reserved.

Cost and waste volume reduction in HEPA filter trains by effective pre-filtration

International Nuclear Information System (INIS)

Chadwick, Chris

2007-01-01

Data published elsewhere (Moore, et al., 1992; Bergman et al., 1997) suggests that the then costs of disposable type Glass Fibre HEPA filtration trains to the DOE was $55 million per year (based on an average usage of HEPA panels of 11,748 pieces per year between 1987 and 1990), $50 million of which was attributable to installation, testing, removal and disposal. The same authors suggest that by 1995 the number of HEPA panels being used had dropped to an estimated 4000 pieces per year due to the ending of the Cold War. The yearly cost to the DOE of 4000 units per year was estimated to be $29.5 million using the same parameters that previously suggested the $55 million figure. Within that cost estimate, $300 each was the value given to the filter and $4,450 was given to peripheral activity per filter. Clearly, if the $4,450 component could be reduced, tremendous saving could result, in addition to a significant reduction in the legacy burden of waste volumes. This same cost is applied to both the 11,748 and 4000 usage figures. The work up to now has focussed on the development of a low cost, long life (cleanable), direct replacement of the traditional filter train. This paper will review an alternative strategy, that of preventing the contaminating dust from reaching and blinding the HEPA filters, and thereby removing the need to replace them. What has become clear is that 'low cost' and 'Metallic HEPA' are not compatible terms. The original Bergman et al., 1997 work suggested that 1000 cfm (cubic feet per minute) (1690 m 3 /hr) stainless HEPAs could be commercially available for $5000 each after development (although the $70,000 development unit may be somewhat exaggerated - the authors own company have estimated development units able to be retrofitted into strengthened standard housings would be available for perhaps $30,000). The likely true cost of such an item produced industrially in significant numbers may be closer to $15,000 each. That being the case, the

An Insight Into the Two Costing Technique: Absorption Costing and Marginal Costing

Directory of Open Access Journals (Sweden)

Mariam Nawaz

2013-02-01

Full Text Available This paper will investigate the controversy that is innate between the two costing techniques; Absorption Costing and Marginal Costing and would throw light on which costing technique better serves its purpose in helping management for decision making process and if Marginal Costing technique is concluded as better technique then why it should not be used for external reporting purpose. This paper will only crystallize and highlight the issues descriptively and will not resolve the issues that are inherent between the two costing techniques. The unique thing about this paper is that it is in favor of treating fixed cost as product cost that is it is supporting the advocates of Absorption Costing Technique but it is against to consider profit as a function of production rather it believes that profit should only be considered as function of sales for stock valuation and to help management in decision making process that is, regarding this point it is supporting advocates of Marginal Costing.

Predicting glass-forming compositions in the Al-La and Al-La-Ni systems

International Nuclear Information System (INIS)

Gargarella, P.; de Oliveira, M.F.; Kiminami, C.S.; Pauly, S.; Kuehn, U.; Bolfarini, C.; Botta, W.J.; Eckert, J.

2011-01-01

Research highlights: → The glass-forming ability of the Al-La and Al-La-Ni systems was studied using the λ* and the λ.Δe criteria. → Both criteria predicted with just 1% at. of error the best glass-former verified so far in the Al-La system. → Four new glass-former compositions could be predicted in the Al-La-Ni system using the λ.Δe criterion. → The best glass-former reported so far in the Al-La-Ni system was found. - Abstract: In this work, a criterion considering the topological instability (λ) and the differences in the electronegativity of the constituent elements (Δe) was applied to the Al-La and Al-Ni-La systems in order to predict the best glass-forming compositions. The results were compared with literature data and with our own experimental data for the Al-La-Ni system. The alloy described in the literature as the best glass former in the Al-La system is located near the point with local maximum for the λ.Δe criterion. A good agreement was found between the predictions of the λ.Δe criterion and literature data in the Al-La-Ni system, with the region of the best glass-forming ability (GFA) and largest supercooled liquid region (ΔT x ) coinciding with the best compositional region for amorphization indicated by the λ.Δe criterion. Four new glassy compositions were found in the Al-La-Ni system, with the best predicted composition presenting the best glass-forming ability observed so far for this system. Although the λ.Δe criterion needs further refinements for completely describe the glass-forming ability in the Al-La and Al-La-Ni systems, the results demonstrated that this criterion is a good tool to predict new glass-forming compositions.

Influence of material and testing parameters on the lifetime of TBC systems with MCrAlY and NiPtAl bondcoats

Energy Technology Data Exchange (ETDEWEB)

Song, Peng

2012-08-31

need to propagate through the TBC to cause macroscopic failure. The rate of crack propagation in the TBC is a critical step, which depends substantially on its microstructural properties. In addition to the TBC-porosity the bondcoat roughness profile is shown to be an important parameter, which to a large extent determines the rate of crack initiation and propagation. Higher Co-content in the bondcoat was found to stabilize its microstructure thereby lowering the CTE-mismatch stress in the ceramic topcoat thus extending the TBC-lifetime. The major drawback of high Co-contents was that such bondcoats are prone to form fast-growing spinel oxides. This effect, which was especially pronounced on rough surfaces could be suppressed by only a minor (few microns) enrichment of Al on the bondcoat surface prior to TBC- deposition produced by heat-treatment in high vacuum. With respect to the effects of experimental parameters it was found that contrary to EB-PVD TBC systems a higher cycle frequency leads to shortening of the APS TBC lifetime, whereas higher water vapor content had no significant influence. The results of the present work indicate that the lifetime of the TBC systems with MCrAlY bondcoats would be shorter than that required for long-term operation (25 000 hours) at the envisaged operating temperature of 1000 C. Under such circumstances using NiPtAl-type of bondcoats or perhaps Pt-modified MCrAlY-bondcoats would be an option to obtain the necessary lifetime extension, which can even justify the high cost of metallic Pt.

Low-energy mechanically milled τ-phase MnAl alloys with high coercivity and magnetization

International Nuclear Information System (INIS)

Lu, Wei; Niu, Junchao; Wang, Taolei; Xia, Kada; Xiang, Zhen; Song, Yiming; Zhang, Hong; Yoshimura, Satoru; Saito, Hitoshi

2016-01-01

The high cost of rare earth elements makes the use of high-performance permanent magnets commercially very expensive. MnAl magnetic material is one of the most promising Rare-Earth-free permanent magnets due to its obvious characteristics. However, the coercivity of MnAl alloys produced by melt spinning followed by appropriate treatment is relatively low. In this investigation, a high coercivity up to 5.3 kOe and saturation magnetization of ∼62 emu/g (with an applied magnetic field of 19.5 kOe) were obtained in the mechanically milled τ-phase Mn_5_7Al_4_3 alloy. As milling time goes on, the coercivity firstly increases and then decreases, leading to the formation of knee-point coercivity, while the saturation magnetization decreases simultaneously. The structural imperfections such as disordering and defects play the most important role in the changes of magnetic properties of τ-phase MnAl alloys processed by low-energy mechanical milling. The present results will be helpful for the development of processing protocols for the optimization of τ-phase MnAl alloys as high performance Rare-Earth-free permanent magnets. - Highlights: • Successful fabrication of pure τ-phase Mn_5_7Al_4_3 alloy by melt spinning and low-energy ball milling processes. • High coercivity (~5.3 kOe) and magnetization (~62 emu/g) were obtained in τ-phase Mn_5_7Al_4_3 alloy. • Disordering and defects play the most important role in the changes of magnetic properties.

Low-energy mechanically milled τ-phase MnAl alloys with high coercivity and magnetization

Energy Technology Data Exchange (ETDEWEB)

Lu, Wei, E-mail: weilu@tongji.edu.cn [School of Materials Science and Engineering, Shanghai Key Lab. of D& A for Metal-Functional Materials, Tongji University, Shanghai 200092 (China); Research Center for Engineering Science, Akita University, Akita 010-8502 Japan (Japan); Niu, Junchao; Wang, Taolei; Xia, Kada; Xiang, Zhen; Song, Yiming [School of Materials Science and Engineering, Shanghai Key Lab. of D& A for Metal-Functional Materials, Tongji University, Shanghai 200092 (China); Zhang, Hong; Yoshimura, Satoru; Saito, Hitoshi [Research Center for Engineering Science, Akita University, Akita 010-8502 Japan (Japan)

2016-08-05

The high cost of rare earth elements makes the use of high-performance permanent magnets commercially very expensive. MnAl magnetic material is one of the most promising Rare-Earth-free permanent magnets due to its obvious characteristics. However, the coercivity of MnAl alloys produced by melt spinning followed by appropriate treatment is relatively low. In this investigation, a high coercivity up to 5.3 kOe and saturation magnetization of ∼62 emu/g (with an applied magnetic field of 19.5 kOe) were obtained in the mechanically milled τ-phase Mn{sub 57}Al{sub 43} alloy. As milling time goes on, the coercivity firstly increases and then decreases, leading to the formation of knee-point coercivity, while the saturation magnetization decreases simultaneously. The structural imperfections such as disordering and defects play the most important role in the changes of magnetic properties of τ-phase MnAl alloys processed by low-energy mechanical milling. The present results will be helpful for the development of processing protocols for the optimization of τ-phase MnAl alloys as high performance Rare-Earth-free permanent magnets. - Highlights: • Successful fabrication of pure τ-phase Mn{sub 57}Al{sub 43} alloy by melt spinning and low-energy ball milling processes. • High coercivity (~5.3 kOe) and magnetization (~62 emu/g) were obtained in τ-phase Mn{sub 57}Al{sub 43} alloy. • Disordering and defects play the most important role in the changes of magnetic properties.

Visible-blind and solar-blind detection induced by defects in AlGaN high electron mobility transistors

Science.gov (United States)

Armstrong, Andrew M.; Klein, Brianna; Allerman, Andrew A.; Douglas, Erica A.; Baca, Albert G.; Crawford, Mary H.; Pickrell, Greg W.; Sanchez, Carlos A.

2018-03-01

Visible- and solar-blind detection was demonstrated using Al0.45Ga0.55N/Al0.30Ga0.70N and Al0.85Ga0.25N/Al0.70Ga0.30N high electron mobility transistors (HEMTs), respectively. Peak responsivities (S) of 3.9 × 106 A/W in the saturation mode and 6.2 × 104 A/W in the pinch-off mode were observed for the visible-blind Al0.45Ga0.55N/Al0.30Ga0.70N HEMT, and a peak S of 4.9 × 104 A/W was observed for the solar-blind Al0.85Ga0.15N/Al0.70Ga0.30N HEMT in the saturation mode. Spectrally resolved photocurrent investigation indicated that sub-bandgap absorption by defect states was the primary origin of the HEMTs' photoresponse. Defect-mediated responsivity caused slow photocurrent rise and fall times, but electrical pulsing was used to improve the bandwidth at the cost of optical gain. Operating HEMTs in this dynamic mode achieved a 25 Hz bandwidth with S = 2.9 × 105 A/W in accumulation and S = 2.0 × 104 A/W in pinch-off for visible-blind detection and S = 5.1 × 103 A/W for solar-blind detection.

The Potential of Urban Agriculture in Montréal: A Quantitative Assessment

Directory of Open Access Journals (Sweden)

Daniel Haberman

2014-09-01

Full Text Available Growing food in urban areas could solve a multitude of social and environmental problems. These potential benefits have resulted in an increased demand for urban agriculture (UA, though quantitative data is lacking on the feasibility of conversion to large-scale practices. This study uses multiple land use scenarios to determine different spaces that could be allocated to vegetable production in Montréal, including residential gardens, industrial rooftops and vacant space. Considering a range of both soil-bound and hydroponic yields, the ability of these scenarios to render Montréal self-sufficient in terms of vegetable production is assessed. The results show that the island could easily satisfy its vegetable demand if hydroponics are implemented on industrial rooftops, though these operations are generally costly. Using only vacant space, however, also has the potential to meet the city’s demand and requires lower operating costs. A performance index was developed to evaluate the potential of each borough to meet its own vegetable demand while still maintaining an elevated population density. Most boroughs outside of the downtown core are able to satisfy their vegetable demand efficiently due to their land use composition, though results vary greatly depending on the farming methods used, indicating the importance of farm management.

Electric quadrupole moments of neutron-rich nuclei {sup 32}Al and {sup 31}Al

Energy Technology Data Exchange (ETDEWEB)

Kameda, D., E-mail: kameda@ribf.riken.jp; Ueno, H. [RIKEN Nishina Center (Japan); Asahi, K.; Nagae, D.; Takemura, M.; Shimada, K. [Tokyo Institute of Technology, Department of Physics (Japan); Yoshimi, A.; Nagatomo, T.; Sugimoto, T. [RIKEN Nishina Center (Japan); Uchida, M.; Arai, T.; Takase, K.; Suda, S.; Inoue, T. [Tokyo Institute of Technology, Department of Physics (Japan); Murata, J.; Kawamura, H. [Rikkyo University, Department of Physics (Japan); Watanabe, H. [Australian National University, Department of Nuclear Physics (Australia); Kobayashi, Y.; Ishihara, M. [RIKEN Nishina Center (Japan)

2007-11-15

The electric quadrupole moments for the ground states of {sup 32}Al and {sup 31}Al have been measured by the {beta} ray-detected nuclear quadrupole resonance method. Spin-polarized {sup 32}Al and {sup 31}Al nuclei were obtained from the fragmentation of {sup 40}Ar projectiles at E/A = 95 MeV/nucleon, and were implanted in a single crystal {alpha}-Al{sub 2}O{sub 3} stopper. The measured Q moment of {sup 32}Al, |Q({sup 32}Al)| = 24(2) mb, is in good agreement with a conventional shell-model calculation with a full sd model space and empirical effective charges, while that of {sup 31}Al is considerably smaller than the sd calculations.

The constitution of alloys in the Al-rich corner of the Al-Si-Sm ternary system

International Nuclear Information System (INIS)

Markoli, B.; Spaic, S.; Zupanic, F.

2001-01-01

The constitution of alloys and the liquidus surface in the Al-rich corner of the Al-Si-Sm ternary system were determined by the examination of controlled heated and cooled specimens, as well as heat-treated specimens by means of optical and scanning electron microscopy, energy-dispersive X-ray spectroscopy, differential thermal analysis and X-ray diffraction. The Al-rich corner of the Al-Si-Sm ternary system comprises five regions of primary crystallisation (α Al , β Si , Al 3 Sm, Al 2 Si 2 Sm and AlSiSm) with following characteristic invariant reaction sequences: ternary eutectic reaction L → α Al + β Si + Al 2 Si 2 Sm, and two liquidus transition reactions, i. e., L + Al 3 Sm → α Al + AlSiSm, and L + AlSiSm → α Al + Al 2 Si 2 Sm. Along with the position of ternary eutectic and both interstitial points in the Al-rich corner of the Al-Si-Sm ternary system, the temperatures for each reaction were determined. (orig.)

A preparation method and effects of Al-Cr coating on NdFeB sintered magnets

Energy Technology Data Exchange (ETDEWEB)

Zheng, Jingwu [College of Chemical Engineering and Materials Science, Zhejiang University of Technology, Hangzhou 310032 (China); Lin, Min, E-mail: linm@nimte.ac.cn [Key Laboratory of Magnetic Materials and Devices, Ningbo Institute of Material Technology and Engineering Chinese Academy of Science, 519 Road Zhuangshi, District Zhenghai, Ningbo 315201, People' s Republic of China (China); Xia, Qingping [College of Chemical Engineering and Materials Science, Zhejiang University of Technology, Hangzhou 310032 (China)

2012-11-15

A 50 {mu}m Al-Cr coating on NdFeB sintered magnets was prepared through dipping in solution, shaking dry and heating at 300 Degree-Sign C. The morphology and composition of the Al-Cr coating were investigated with scanning electron microscope, energy dispersive spectrometer and X-ray diffraction. The corrosion resistance of NdFeB sintered magnets with and without the Al-Cr coating was analyzed by normal salt spray, polarization curves and electrochemical impedance spectroscopy. The magnetic properties were measured with a hysteresis loop tracer. The results show that the Al-Cr coating forms an overlapping structure and Al flakes lie nearly parallel to the substrate, which improves the anticorrosion and increases normal salt spray test from 10 to 100 h. The corrosion potential of NdFeB sintered magnets with and without the Al-Cr coating moves positively from -0.67 to -0.48 V, which is in accordance with Nyquist and Bode plots. The Al-Cr coating has little influence on the magnetic properties of the NdFeB sintered magnets. - Highlights: Black-Right-Pointing-Pointer The Al-Cr coating can be prepared by dipping in solution, shaking dry and heating. Black-Right-Pointing-Pointer The coating morphology shows to be an intense overlapping structure. Black-Right-Pointing-Pointer The barrier effect combines with passivation and cathodic protection. Black-Right-Pointing-Pointer The anticorrosion abilities improve while magnetic properties change little. Black-Right-Pointing-Pointer Compared with other surface treatments, this method is convenient and low cost.

Disordered crystal structure of 20H-AlON, Al10O3N8

International Nuclear Information System (INIS)

Banno, Hiroki; Funahashi, Shiro; Asaka, Toru; Hirosaki, Naoto; Fukuda, Koichiro

2015-01-01

The disordered crystal structure of 20H-AlON (Al 10 O 3 N 8 ) was determined by combined use of X-ray powder diffraction and transmission electron microscopy. The title compound is hexagonal with space group P6 3 /mmc (Z=2) and the unit-cell dimensions are a=0.307082(5) nm, c=5.29447(8) nm and V=0.432376(12) nm 3 . The structural model showed the positional disordering of three of the six Al sites in the unit cell. The reliability indices calculated from the Rietveld method were R wp =6.97%, S (=R wp /R e )=1.68, R p =5.45%, R B =5.13% and R F =4.56%. We interpreted the disordered structure of 20H-AlON as a statistical average of six different types of ordered structural configurations, which are composed of an octahedral [Al(O, N) 6 ] layer and tetrahedral [Al(O, N) 4 ] layers. We demonstrated the high correlations between the hexagonal unit-cell dimensions and the octahedral layer concentrations for AlON and SiAlON polytypoids. - Graphical abstract: Variations of a and c/(n O +n T ) with n O /(n O +n T ). The a and c are the hexagonal unit-cell dimensions of AlON, SiAlON and AlN. The n O and n T are, respectively, the numbers of octahedral and tetrahedral layers in the unit cells. The unit-cell dimensions in literature are plotted in black plus for AlON and black cross for SiAlON. The unit-cell dimensions of AlN are a=0.3110 nm and c=0.4980 nm. - Highlights: • Crystal structure of Al10O3N8 is determined by laboratory X-ray powder diffraction. • The atom arrangements are represented by the split-atom model. • Six types of ordered atom arrangements are derived from the disordered structure. • Hexagonal unit-cell dimensions changed systematically for AlON and SiAlON compounds

Prinsip Pendidikan Karakter dalam Islam: Studi Komparasi Pemikiran Al-Ghazali dan Burhanuddin Al-Zarnuji

Directory of Open Access Journals (Sweden)

Agus Setiawan

2014-06-01

Full Text Available The impelemtantion of character education that is done by the Indonesian government recently has been provoked by al-Ghazali and Burhanuddin al-Zarnuji long ago. It was proven by some written thoughts of al-Ghazali and Burhanuddin al-Zarnuji. They were very famous scientists in their era and widely welknown as educational experts who produced some phenomenal thoughts many people use today. Al-Ghazali and Burhanuddin al-Zarnuji lived in the era of Bani Abbasiyah monarchy, but Both of them lived in different era. Al-Ghazali was born first, then Burhanuddin al-Zarnuji. They had different mazhab, al-Ghazali went to the traditional principle of mazhab Syafi’I and Burhanuddin al-Zarnuji went to the modern principle of mazhab Hanafi. The differences, of course, would create a different thought. Still, they might have a similar principle of Islamic character education. The thoughts of character education of al-Ghazali have been poured in the “Ayyuha Walad” focusing to the students’ character building characterized by religiously obedient, skillfull of general and religious knowledge, socially helpful, affectionate, generous, good citizen, and coloring the society. Some applicable thoughts of character education of Ayyuha al-Walad of al-Gazhali to the contemporary education are: the balance of the happiness purposes of the recent life and the life after death, qana’ah and tawakal, affectionate, caring other, patience, honesty, philanthrophy, social works, generousity, democratic, peace makers, and patriotic. Those characters are also directed in the islamic character education nowdays. So that, the thoughts of al-Ghazali positively and responsively are absorbed by the Indonesian government to build the national character widely implementing in the national curriculum based on the local wisdom and the Islamic values. In the end, the students are able to live happily based on the Islamic rules by implementing the good behavior. Similar to the al

Sintering behavior and property of bioglass modified HA-Al2O3 composite

Directory of Open Access Journals (Sweden)

Wang Li-li

2012-01-01

Full Text Available The bioglass modified HA-Al2O3 composites were successfully fabricated by mixing HA, synthesized by wet chemical method between precursor materials H3PO4 and Ca(OH2, with 25wt% Al2O3 and different content of bioglass (5%, 25%, 45%, 65wt% respectively, with a mole fraction of 53.9%SiO2, 22.6%Na2O, 21.8%CaO, and 1.7wt%P2O5, sintered in air at various temperatures (750-950°C for 2h. when the content of bioglass is below 45wt% in the composite, HA decomposes completely and transforms to β-TCP. The main phase in this case are β-TCP, Al2O3 and Ca3(AlO32.When the content of bioglass is above 45wt% in the composite, the decomposition of HA to β-TCP is suppressed and the main phases in this case are Al2O3 and HA, DCP□CaHPO4□ and β-TCP, which almost have the same chemical composition, forming ternary-glass phase, and have better bioactive than pure HA. It can also be found that at the certain addition of bioglass, the higher sintered temperature, the bigger volume density and flexural strength of the composite are, but when the sintered temperature reaches 950°C, they decrease. This modified HA-Al2O3 composites by calcium silicate glass have a much lower sintering temperature and decrease the production cost much.

FRACTIONAL RECRYSTALLIZATION KINETICS IN DIRECTLY COLD ROLLED Al-Mg, Al-Mg-Sc AND Al-Mg-Sc-Zr ALLOY

Directory of Open Access Journals (Sweden)

M. S. Kaiser

2014-12-01

Full Text Available The evaluation of texture as a function of recrystallization has been characterized for directly cold rolled Al-6Mg, Al-6Mg-0.4Sc and Al-6Mg-0.4Sc-0.2Zr alloys. Samples were annealed isothermally at 400 °C for 1 to 240 minutes to allow recrystallization. Recrystallization kinetics of the alloys is analyzed from the micro-hardness variation. Isothermally annealed samples of aluminum alloys were also studied using JMAK type analysis to see if there exists any correlation between the methods. Recrystallization fraction behavior between two methods the scandium added alloys show the higher variation due to precipitation hardening and higher recrystallization behavior. The scandium and zirconium as a combined shows the more variation due to formation of Al3(Sc, Zr precipitate. From the microstructure it is also observed that the base Al-Mg alloy attained almost fully re-crystallized state after annealing at 400 °C for 60 minutes

Chemical failure modes of AlQ3-based OLEDs: AlQ3 hydrolysis.