Production of High-purity Magnetite Nanoparticles from a Low-grade Iron Ore via Solvent Extraction

Energy Technology Data Exchange (ETDEWEB)

Suh, Yong Jae; Kil, Dae Sup; Jang, Hee Dong [Korea Institute of Geoscience and Mineral Resources, Daejeon (Korea, Republic of); Do, Thi May [Korea University of Science and Technology, Daejeon (Korea, Republic of); Cho, Kuk [Pusan National University, Busan (Korea, Republic of)

2015-02-15

We produced magnetite nanoparticles (MNPs) and a Mg-rich solution as a nano-adsorbent and a coagulant for water treatment, respectively, using a low-grade iron ore. The ore was leached with aqueous hydrochloric acid and its impurities were removed by solvent extraction of the leachate using tri-n-butyl phosphate as an extractant. The content of Si and Mg, which inhibit the formation of MNPs, was reduced from 10.3 wt% and 15.5 wt% to 28.1 mg/L and < 1.4 mg/L, respectively. Consequently, the Fe content increased from 68.6 wt% to 99.8 wt%. The high-purity Fe{sup 3+} solution recovered was used to prepare 5-15-nm MNPs by coprecipitation. The wastewater produced contained a large amount of Mg{sup 2+} and can be used to precipitate struvite in sewage treatment. This process helps reduce the cost of both sewage and iron-ore-wastewater treatments, as well as in the economic production of the nano-adsorbent.

Status report from India [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

Fareeduddin, S [Atomic Energy Establishment, Trombay, Bombay (India)

1967-06-15

The Energy Survey Committee of India, in its report to the Government, has estimated that the energy requirements in the year 1985/86 would be 290X10{sup 9} kWh, i. e. eight times the present requirement, and in the year 2000 it would be 820X10{sup 9} kWh, which is about 22 times the present requirement. The hydropotential that can be developed during the next 20 years is estimated to be of the order of 150X10{sup 9} kWh and hence the difference of about 140X10{sup 9} kWh will have to be obtained from either fossil or nuclear fuel. This would mean installating a generation capacity of about 26 000 MW in the next 20 years. To conserve the limited fossil fuel reserves, it has been estimated that about 70% of this capacity, i. e. about 18 000 MW, should form the nuclear component. This will be about 25% of the total energy requirements by 1985/86. The uranium requirements to meet this growth will be about 10 000 tonnes by 1985/86 which, from the point of view of our resources, is a substantial quantity. The most important uranium deposits are located in South Bihar in the Singhbhum Thrust belt, which is well known for its copper, apatite magnetite and kyanite deposits. On the basis of their uranium contents, these ores can be classified into two broad categories - one with low copper and high uranium contents and the other with high copper and low uranium contents. Another source of uranium in India is monazite. Some particulars about these deposits are given. Facilities for the recovery of byproduct uranium from monazite already exist in the country. But its production from this source, conditioned as it is by the limited demand for thorium, cannot be very large. Both the categories of the ores from the Singhbhum belt can be considered as low grade. Uranium from the ores in category (B) can be recovered, in the present state of knowledge, only as a byproduct of the copper industry. In the case of ores in the category (A), attempts have been made to recover uranium

Ferrite grade iron oxides from ore rejects

Indian Academy of Sciences (India)

Iron oxyhydroxides and hydroxides were synthesized from chemically beneficiated high SiO2/Al2O3 low-grade iron ore (57.49% Fe2O3) rejects and heated to get iron oxides of 96–99.73% purity. The infrared band positions, isothermal weight loss and thermogravimetric and chemical analysis established the chemical ...

Beneficiation and leaching study of a muti-Au carrier and low grade refractory gold ore

Science.gov (United States)

Li, W. J.; Song, Y. S.; Chen, Y.; Cai, L. L.; Zhou, G. Y.

2017-09-01

Detailed mineralogy and beneficiation and leaching study of a muti-Au carrier, low grade refractory gold ore from a beneficiation plant in Henan Province, China, was investigated. Mineral liberation analysis, scanning electron microscopy, element phase analysis and etc. by a mineral liberation analyser were used for mineralogical characterization study of this ore. The present work describes an experimental study on the effect of traditional parameters (such as grinding fineness and reagent regimes), middling processing method and flowsheet construction on the total recovery and the assay of the floatation concentrate. Two-step floatation and part of middling combined to the floatation tailing for gold leaching process resulted in high gold grade (g.t-1) and gold recovery (%) for this refractory gold ore. This process opens the possibilities of maximizing Au grade and recoveries in a muti-Au carrier and low grade refractory gold ore where low recoveries are common.

Processing of Low-Grade Uranium Ores. Proceedings of a Panel

International Nuclear Information System (INIS)

1967-01-01

The 22 specialists from 15 countries and one international organization who attended the meeting were asked to give an appraisal of the current situation with regard to the processing of low-grade uranium ores and make recommendations for a possible IAEA programme of activities. This publication covers the work of the panel. Contents: Status reports (13 reports); Technical reports (13 reports); Summaries of discussions; Recommendations of the panel. Each report is in its original language (16 English, 4 French, 2 Russian and 4 Spanish) and each technical report is preceded by an abstract in English and one in the original language if this is not English. The summaries of discussions and the panel recommendations are in English. (author)

Processing of Low-Grade Uranium Ores. Proceedings of a Panel

Energy Technology Data Exchange (ETDEWEB)

NONE

1967-06-15

The 22 specialists from 15 countries and one international organization who attended the meeting were asked to give an appraisal of the current situation with regard to the processing of low-grade uranium ores and make recommendations for a possible IAEA programme of activities. This publication covers the work of the panel. Contents: Status reports (13 reports); Technical reports (13 reports); Summaries of discussions; Recommendations of the panel. Each report is in its original language (16 English, 4 French, 2 Russian and 4 Spanish) and each technical report is preceded by an abstract in English and one in the original language if this is not English. The summaries of discussions and the panel recommendations are in English. (author)

The separation of ore from cooke into high- and low-grade fractions

International Nuclear Information System (INIS)

Guest, R.N.

1984-01-01

The separation of the ore by sizing alone was not very successful, and the recovery of uranium to the high-grade fraction did not exceed 73 per cent. The use of a combination of size and gravity separation was attempted, and the tailing from the gravity circuit contained 33,9 per cent of the uranium at a grade of 60g/t. The circuit recommended includes autogenous grinding to liberate part of the ore matrix containing the values into the fine fraction. This should be followed by heavy-medium separation for the recovery of the high-grade portion of the coarse fraction. The size at which this heavy-medium separation is carried out should be determined

Uranium Processing Research in Australia [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

Stewart, J R [Australian Atomic Energy Commission, Coogee, N.S.W. (Australia)

1967-06-15

Uranium processing research in Australia has included studies of flotation, magnetic separation, gravity separation, heavy medium separation, atmospheric leaching, multi-stage leaching, alkali leaching, solar heating of leach pulps, jigged-bed resin-in-pulp and solvent-in-pulp extraction. Brief details of the results obtained are given. In general, it can be said that gravity, magnetic and flotation methods are of limited usefulness in the treatment of Australian uranium ores. Alkali leaching seldom gives satisfactory recoveries and multi-stage leaching is expensive. Jigged-bed resin-in-pulp and packed tower solvent-in-pulp extraction systems both show promise, but plant-scale development work is required. Bacterial leaching may be useful in the case of certain low-grade ores. The main difficulties to be overcome, either singly or in combination, in the case of Australian uranium ores not currently considered economically exploitable, are the extremely finely divided state of the uranium mineral, the refractory nature of the uranium mineral and adverse effects due to the gangue minerals present. With respect to known low-grade ores, it would be possible in only a few cases to achieve satisfactory recovery of uranium at reasonable cost by standard treatment methods. (author)

Status Report from the United Kingdom [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

North, A A [Warren Spring Laboratory, Stevenage, Herts. (United Kingdom)

1967-06-15

The invitation to present this status report could have been taken literally as a request for information on experience gained in the actual processing of low-grade uranium ores in the United Kingdom, in which case there would have been very little to report; however, the invitation naturally was considered to be a request for a report on the experience gained by the United Kingdom of the processing of uranium ores. Lowgrade uranium ores are not treated in the United Kingdom simply because the country does not possess any known significant deposits of uranium ore. It is of interest to record the fact that during the nineteenth century mesothermal vein deposits associated with Hercynian granite were worked at South Terras, Cornwall, and ore that contained approximately 100 tons of uranium oxide was exported to Germany. Now only some 20 tons of contained uranium oxide remain at South Terras; also in Cornwall there is a small number of other vein deposits that each hold about five tons of uranium. Small lodes of uranium ore have been located in the southern uplands of Scotland; in North Wales lower palaeozoic black shales have only as much as 50 to 80 parts per million of uranium oxide, and a slightly lower grade carbonaceous shale is found near the base of the millstone grit that occurs in the north of England. Thus the experience gained by the United Kingdom has been of the treatment of uranium ores that occur abroad.

Recovery of uranium from low-grade sandstone ores and phosphate rock

Energy Technology Data Exchange (ETDEWEB)

Kennedy, R H [United States Atomic Energy Commission, Washington, D. C. (United States)

1967-06-15

This paper is concerned principally with commercial-scale experience in the United States in the recovery of uranium from low-grade sources. Most of these operations have been conducted by the operators of uranium mills as an alternative to processing normal-grade ores. The operations have been generally limited, therefore, to the treatment of low-grade materials generated in the course of mining normal-grade ores. In some circumstances such materials can be treated by simplified procedures as an attractive source of additional production. The experience gained in uranium recovery from phosphate rock will be treated in some detail. The land pebble phosphate rock of central Florida generally contains about 0.01 to 0.02% U{sub 3}O{sub 8}. While no uranium is being recovered from this source at the present time, it does represent a significant potential source of by-product uranium production because of the large tonnages being mined. (author)

Bacterial bioleaching of low grade nickel limonite and saprolite ores by mixotrophic bacteria

Directory of Open Access Journals (Sweden)

Chaerun Siti Khodijah

2016-01-01

Full Text Available Utilization of indigenous bacteria should be considered to establish a successful biohydrometallurgical process. In this study, mixrotrophic iron-oxidizing bacterial consortia consisting of Comamonas testosteroni, Alicyclobacillus ferrooxydans and Pantoea septic which were isolated from Indonesian mineral ores were examined to determine their abilities to recover nickel from limonite and saprolite ores in the bioleaching experiments using stirred tank reactors. The nickel bioleaching experiments inoculated with the bacterial consortia were carried out using coarse limonite ores and weathered saprolite ores with pulp density of 10% w/v. Abiotic controls were also carried out replacing the inocula by the sterile medium. The bioleaching processes were monitored by measuring Ni and Fe contents and pH of the leaching solution as well as the total bacterial enzymatic activity measured as FDA hydrolytic activity. The effect of leaching on the mineralogy of laterite ores was investigated by the scanning electron microscope equipped with energy-dispersive spectroscopy (SEM-EDS and X-ray powder diffraction (XRD. After 28 days of incubation, the FDA hydrolytic activity was observed in both bioleaching experiments containing limonite (17.2 μg fluorescein/mL and saprolite ores (16.9 μg fluorescein/mL. The leached Ni and Fe in the bioleaching experiments containing limonite ores (30% Ni and 5.6% Fe was greater than that in abiotic controls (1% Ni and 0.1% Fe with the pH range of 2.5 to 3.5. However, the bacterial consortia were less capable of bioleaching of Ni (2.5% with the similar leached Fe (6% from the saprolite ores. In abiotic controls, the medium pH remained relatively constant (pH 6. It was concluded that these bacterial isolated as the consortium were capable of nickel bioleaching (precious metal more effectively than iron (gangue metal, thus being applicable to the commercial processing of the difficult-to-process low-grade nickel laterite ores

An instrument for rapid delineation of grade boundaries in selective mining of uranium ore

International Nuclear Information System (INIS)

Clark, G.J.; Dickson, B.L.; Meakins, R.L.; Kenny, D.; Talaska, A.

1982-01-01

A vehicle-mounted radiation detector interfaced to a microprocessor called PRAM (programmable radioactive analyser mobile) has been developed to provide grade control for selective mining of a soft rock uranium ore. The grade of ore over which the vehicle passes is determined and indicated by several coloured lights to a pegman who walks behind the vehicle. Coloured pegs are then laid out to mark the uranium grade ranges on the floor of the mine pit. Comparison between grade ranges determined by the PRAM and by prior drilling and downhole logging at the Yeelirrie deposit, Western Australia indicate good agreement. Use of the PRAM decreases the cost, manpower and time required to grade extensive areas of a mine pit floor

Feasibility Studies for Production of Pellet Grade Concentrate from Sub Grade Iron Ore Using Multi Gravity Separator

Science.gov (United States)

Rao, Gottumukkala Venkateswara; Markandeya, R.; Kumar, Rajan

2018-04-01

An attempt has been made to utilise Sub Grade Iron Ore by producing pellet grade concentrate from Deposit 5, Bacheli Complex, Bailadila, Chhattisgarh, India. The `as received' Run of Mine (ROM) sample assayed 40.80% Fe, 40.90% SiO2. Mineralogical studies indicated that the main ore mineral is Hematite and lone gangue mineral is Quartz. Mineral liberation studies indicated that, the ore mineral Hematite and gangue mineral Quartz are getting liberated below 100 microns. The stage crushed and ground sample was subjected to concentration by using a Multi Gravity Separator (MGS). Rougher Multi Gravity Separation (MGS) experimental results were optimised to recover highest possible iron values. A concentrate of 55.80% Fe with a yield of 61.73% by weight with a recovery of 84.42% Iron values was obtained in rougher MGS concentrate. Further experiments were carried out with rougher MGS concentrate to produce a concentrate suitable for commercial grade pellet concentrate. It was proved that a concentrate assaying 66.67% Fe, 3.12% SiO2 with an yield of 45.08% by weight and with a recovery of 73.67% iron values in the concentrate.

Development of the heap leaching of low-grade uranium ores for conditions of OJSC Priargunsky Mining and Chemical plant (PPGKhO)

International Nuclear Information System (INIS)

Morozov, A.; Litvinenko, V.

2014-01-01

The treatment of low-grade commercial uranium ores by heap leaching has been carried out at the enterprise since 1996. During the initial stage of development, the ore piles were formed of the raw ore having the run-of-mine coarseness with uranium content around 0.08%. Under such conditions, recovery of the metal to the solution is 60-65% in case of a pile treatment lasting 2 years. To intensify the process and to provide a stable concentration of uranium in the productive solutions transferred to sorption, the enterprise developed and implemented a method of percolation leaching of low-grade ores with re-circulation of productive solutions through the re-treated ore bulk (RF patent No. 2226564). The main peculiarity of such leaching is simultaneous moistening of the ore by productive solutions and by barren solutions that are sharpened with sulphuric acid; that gives the possibility to wet far bigger areas of piles under constant volume of productive solutions outputting to the sorption treatment. Such scheme enables to treat successively first the piles at the “re-treatment” (where the metal is mainly extracted), and then the piles at the “active leaching” stage (where the metal is mainly inside the ore bulk). The technical and economic indexes of the heap leaching of low-grade uranium ores were significantly increased in 2006, when the X-ray-radiometric treatment plant was commissioned. The technological scheme of ore treatment at the processing plant includes mould and grating of the raw material with delivery of undersized products enriched with uranium: -5 mm are transferred to the pulp process; fractions (-200+40) mm to the X-ray-radiometric separation; the material of size (-40+5) mm, washed-out from clayey and fine particles, are sent to the uranium heap leaching in piles. Delivery of the ore material having size (-40+5) mm to treatment by the acid leaching method excluded colmatage and creation of zones impermeable for water, and in combination

Distribution of uranium in two sulphide ore environments from the reversed metamorphic sequence of the Daling Rocks in the Dargeeling-Sikkim Himalaya, India

International Nuclear Information System (INIS)

Ghosh, A.K.

1988-01-01

In the low-grade Daling metasediments of Gorubathan, the average U content of 3-4 ppm reflects the original U content of the unmetamorphosed sediments. The high-grade metasediments of Dichu averag 6 ppm, and the sulphide ores of this area also have more U compared to Gorubathan ores.This higher U content in the high-grade rocks and in the associated ores is believed to be the result of enrichment during metasomatic activity in the area. Neverthelessthe fact that the Daling metasediments have higher U contents thanthat of the sulphide ores appears to be independent of the grade of metamorphism in the progressive sequence

Processing of Low-Grade Uranium Ores. Proceedings of a Panel

Energy Technology Data Exchange (ETDEWEB)

NONE

1967-06-15

Proceedings of a panel convened by the IAEA in Vienna, 27 June - 1 July 1966. The 22 specialists from 15 countries and one international organization who attended the meeting were asked to give an appraisal of the current situation with regard to the processing of low-grade uranium ores and make recommendations for a possible IAEA programme of activities. This publication covers the work of the panel. Contents: Status reports (13 reports); Technical reports (13 reports); Summaries of discussions; Recommendations of the panel. Each report is in its original language (16 English, 4 French, 2 Russian and 4 Spanish) and each technical report is preceded by an abstract in English and one in the original language if this is not English. The summaries of discussions and the panel recommendations are in English. (author)

Status Report from the United States of America [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

Kennedy, R H [United States Atomic Energy Commission, Washington, D.C. (United States)

1967-06-15

The US uranium production rate has been dropping gradually from a high of 17 760 tons in fiscal year 1961 to a level of about 10 400 tons in fiscal year 1966. As of 1 January 1966, there were 17 uranium mills in operation in the USA compared with a maximum of 26 during 1961, the peak production year. Uranium procurement contracts between the USAEC and companies operating 11 mills have been extended through calendar year 1970. The USAEC contracts for the other six mills are scheduled to expire 31 December 1966. Some of these mills, however, have substantial private orders for production of uranium for nuclear power plants and will continue to operate after completion of deliveries under USAEC contracts. No new uranium mills have been brought into production since 1962. Under these circumstances the emphasis in process development activities in recent years has tended toward improvements that could be incorporated within the general framework of the existing plants. Some major flowsheet changes have been made, however. For example, two of the ore-processing plants have shifted from acid leaching to sodium carbonate leach in order to provide the flexibility to process an increasing proportion of ores of high limestone content in the tributary areas. Several mills employing ion exchange as the primary step for recovery of uranium from solution have added an 'Eluex' solvent extraction step on the ion exchange eluate. This process not only results in a highgrade final product, but also eliminates several metallurgical problems formerly caused by the chloride and nitrate eluants. Such changes together with numerous minor improvements have gradually reduced production cost and increased recoveries. The domestic uranium milling companies have generally had reserves of normal-grade ores well in excess of the amounts required to fulfil the requirements for their contracts with the USAEC. Therefore, there has been little incentive to undertake the processing of lower grade

Continued Multicolumns Bioleaching for Low Grade Uranium Ore at a Certain Uranium Deposit

Directory of Open Access Journals (Sweden)

Gongxin Chen

2016-01-01

Full Text Available Bioleaching has lots of advantages compared with traditional heap leaching. In industry, bioleaching of uranium is still facing many problems such as site space, high cost of production, and limited industrial facilities. In this paper, a continued column bioleaching system has been established for leaching a certain uranium ore which contains high fluoride. The analysis of chemical composition of ore shows that the grade of uranium is 0.208%, which is lower than that of other deposits. However, the fluoride content (1.8% of weight is greater than that of other deposits. This can be toxic for bacteria growth in bioleaching progress. In our continued multicolumns bioleaching experiment, the uranium recovery (89.5% of 4th column is greater than those of other columns in 120 days, as well as the acid consumption (33.6 g/kg. These results indicate that continued multicolumns bioleaching technology is suitable for leaching this type of ore. The uranium concentration of PLS can be effectively improved, where uranium recovery can be enhanced by the iron exchange system. Furthermore, this continued multicolumns bioleaching system can effectively utilize the remaining acid of PLS, which can reduce the sulfuric acid consumption. The cost of production of uranium can be reduced and this benefits the environment too.

Underground bioleaching: extracting from low-grade ore

International Nuclear Information System (INIS)

McCready, R.G.L.

1986-01-01

In 1984, Denison Mines began a research and demonstration project on the engineering aspects of bacterial leaching of low-grade uranium ore at Elliot Lake. The leaching solution was acidic mine water enriched in bacterial nutrients and innoculated with Thiobacillus ferrooxidans. Leaching of one stope was found to be impeded by fungi of the genus penicillium. Although fungal growth on leaching stopes must be prevented, research is proceeding on the potential use of the fungi to concentrate uranium from bioleaching solutions

Preconcentration of a low-grade uranium ore yielding tailings of greatly reduced environmental concerns. Part V

International Nuclear Information System (INIS)

Raicevic, D.; Raicevic, M.

1980-11-01

The low-grade ore sample used for this investigation contained 0.057 percent uranium with uranothorite as the major uranium-bearing mineral and a small amount of brannerite, occurring in the quartz-sericite matrix of a conglomerate. The preconcentration procedures, consisting of pyrite flotation with or without flotation of radioactive minerals, followed by high intensity wet magnetic treatment of the sized flotation tailings, produced pyrite and radioactive concentrates of acceptable uranium grades ranging from 0.1 to 0.135 percent uranium. The combined concentrates comprised 37 to 49 percent of the ore by weight with the following combined recoveries: 95.6 to 97.9 percent of the uranium; 94.7 to 96.3 percent of the radium; 97.8 to 99.3 percent of the thorium over 98 percent of the pyrite. The preconcentration tailings produced comprised between 51 and 63 percent of the ore by weight and contained from: 0.0022 to 0.0037 percent U; 12 to 17 pCi/g Ra; 0.002 to 0.004 percent Th less than 0.03 percent S. Because these tailings are practically pyrite-free, they should not generate acidic conditions. Due to their low radium content, their radionuclide hazards are greatly reduced. These preconcentration tailings therefore, could be suitable for surface disposal, mine backfill, revegetation or other uses

Recovery of metals from low-grade ores by Aspergillus niger

Energy Technology Data Exchange (ETDEWEB)

Kamali, M.; Mulligan, C.N. [Concordia Univ., Dept. of Building, Civil and Environmental Engineering, Montreal, Quebec (Canada)]. E-mail: mulligan@civil.concordia.ca

2002-06-15

The main concern of this study is to develop a feasible and economical technique to microbially recover metals from oxide low-grade ores. Owing to the significant quantities of metals that are embodied in low - grade ores and mining residues, these are considered new sources of metals. On the other hand, they potentially endanger the environment, as the metals they contain may be released to the environment in a hazardous form. Hence, mining industries are seeking an efficient technique to handle these ores. Pyrometallurgical and hydrometallurgical techniques are either very expensive, energy intensive or have a negative impact on the environment. For these reasons, biohydrometallurgical techniques are coming into perspective. In this study, by employing Aspergillus niger, the feasibility of recovery of metals from a mining residue is shown. A. niger exhibits good potential in generating a variety of organic acids effective for metal solubilization. Organic acid effectiveness was enhanced when sulphuric acid was added to the medium. Different agricultural wastes such as potato peels were tested. In addition to this, different auxiliary processes were tried in order to either elevate the efficiency or reduce costs. Finally, maximum solubilization of 68%, 46% and 34% were achieved for copper, zinc and nickel, respectively. Also iron codissolution was minimized as only 7% removal occurred. (author)

Recovery of metals from low-grade ores by Aspergillus niger

International Nuclear Information System (INIS)

Kamali, M.; Mulligan, C.N.

2002-01-01

The main concern of this study is to develop a feasible and economical technique to microbially recover metals from oxide low-grade ores. Owing to the significant quantities of metals that are embodied in low - grade ores and mining residues, these are considered new sources of metals. On the other hand, they potentially endanger the environment, as the metals they contain may be released to the environment in a hazardous form. Hence, mining industries are seeking an efficient technique to handle these ores. Pyrometallurgical and hydrometallurgical techniques are either very expensive, energy intensive or have a negative impact on the environment. For these reasons, biohydrometallurgical techniques are coming into perspective. In this study, by employing Aspergillus niger, the feasibility of recovery of metals from a mining residue is shown. A. niger exhibits good potential in generating a variety of organic acids effective for metal solubilization. Organic acid effectiveness was enhanced when sulphuric acid was added to the medium. Different agricultural wastes such as potato peels were tested. In addition to this, different auxiliary processes were tried in order to either elevate the efficiency or reduce costs. Finally, maximum solubilization of 68%, 46% and 34% were achieved for copper, zinc and nickel, respectively. Also iron codissolution was minimized as only 7% removal occurred. (author)

Heap bioleaching of uranium from low-grade granite-type ore by mixed acidophilic microbes

International Nuclear Information System (INIS)

Xuegang Wang; Zhongkui Zhou

2017-01-01

We evaluated uranium bioleaching from low-grade, granite-type uranium ore using mixed acidophilic microbes from uranium mine leachate. A 4854-ton plant-scale heap bioleaching process achieved sustained leaching with a uranium leaching efficiency of 88.3% using a pH of 1.0-2.0 and an Fe"3"+ dosage of 3.0-5.5 g/L. Acid consumption amounted to 25.8 g H_2SO_4 kg"-"1 ore. Uranium bioleaching follows a diffusion-controlled kinetic model with a correlation coefficient of 0.9136. Almost all uranium was dissolved in aqueous solution, except those encapsulated in quartz particles. Therefore, heap bioleaching by mixed acidophilic microbes enables efficient, economical, large-scale recovery of uranium from low-grade ores. (author)

The measurement and inclusion of a stochastic ore-grade uncertainty in mine valuations using PDEs

OpenAIRE

Evatt, G. W.; Johnson, P. V.; Duck, P. W.; Howell, S. D.

2010-01-01

Mining companies world-wide are faced with the problem of how to accurately value and plan extraction projects subject to uncertainty in both future price and ore grade. Whilst the methodology of modelling price uncertainty is reasonably well understood, modelling ore-grade uncertainty is a much harder problem to formulate, and when attempts have been made the solutions have taken unfeasibly long times to compute. This paper provides a new partial differential equations approach to the proble...

Pilot plant studies on the extraction of antimony metal from lower grade krinj stibnite ore

International Nuclear Information System (INIS)

Rehman, W.; Riaz, M.; Ishaq, M.

2013-01-01

Antimony is a silvery white, brittle and crystalline solid which is extensively consumed in lead acid batteries, antimonial lead alloys, flame retardants and a variety of metallic products. The antimony content of commercial ores range from 5-60% and determines the method of extraction, either pyrometallurgical or hydrometallurgical. The present study focuses on pilot plant scale extraction of antimony metal from lower grade stibnite ore of Krinj (Chitral) without the use of iron scrap, thus eliminating the second step of iron removal in conventional direct reduction method. A tilting gas fired furnace with digital temperature control system and a heat recuperator was designed to optimize the operating parameters for extraction of antimony metal. Weight ratios of flux and reductant, operating time and operating temperature were optimized. Highest percentage recovery and purity were achieved using soda ash as a flux, at a temperature of 900 degree C for 2 hours. (author)

Effects of reduction temperature to Ni and Fe content and the morphology of agglomerate of reduced laterite limonitic nickel ore by coal-bed method

Science.gov (United States)

Abdul, Fakhreza; Pintowantoro, Sungging; Kawigraha, Adji; Nursidiq, Ahlidin

2018-04-01

As the current drop of nickel sulfide ore on earth, the attention to nickel laterite ore processing was inscreased in order to fulfill the future nickel demand needs. This research aims to optimized the process of nickel laterite ore extraction using coal bed method. This research was conducted by reducing low grade nickel laterite ore (limonitic) with nickel content of 1.25 %. The reduction process was carried out using CO gas which formed by the reaction of coal and dolomite. The Briquette of nickel ore, coal, Na2SO4 mixtures incorporated in the crucible with bed, then reduced for 6 hours at the temperature of 1200 °C. 1400 °C, and 1400 °C. The result of the research shown that the highest increase of Ni content and Ni recovery value was in the reduction temperature of 1400 °C with the increase of 3.44 %, and the recovery value of Ni equal to 86.75 %. While the highest increase of Fe content and Fe recovery value, respectively, was in the reduction temperature of 1300 °C with the increase of 22.67 % and 1200 °C with Fe recovery value of 89.41 %.

Use of neutron capture gamma radiation for determining grade of iron ore in blast holes and exploration holes

International Nuclear Information System (INIS)

Eisler, P.L.; Huppert, P.; Mathew, P.J.; Wylie, A.W.; Youl, S.F.

1977-01-01

Neutron radiative capture and neutron-neutron logging have been applied to determining the grade of ore in dry blast holes and a dry exploration hole drilled into a layered iron deposit. Both thermal and epithermal neutron responses were measured as well as the gamma-ray responses due to neutron capture by iron and by hydrogen present in hydrated minerals. The results were fitted by a stepwise multiple linear regression technique to give expressions for mean grade of ore in the drill hole and 95% confidence intervals for estimation of this mean. For an overall range of ore grades of 20-68% Fe and a mean grade of 63% Fe, the confidence interval for prediction of mean grade for the neutron-gamma technique was 0.3% Fe for pooled data from all five blast holes and 0.8% Fe for a single hole. It was also shown that for this type of layered deposit a simpler neutron-neutron log incorporating simultaneous measurement of both thermal and epithermal neutron responses gave almost as good a grade prediction result for pooled results from five drill holes, namely 63+-0.4% Fe, as that obtained by the neutron-gamma technique. The results of both types of log are compared with those obtained by the spectral gamma-ray backscattering [Psub(z)] technique, or by logging of natural gamma radiations from the shale component of the ore. From this comparison conclusions are drawn regarding the most suitable technique to employ for determining grade of iron ore in various practical logging situations. (author)

Influence of the Moisture Content on the Flowability of Fine-Grained Iron Ore Concentrate

OpenAIRE

C. Lanzerstorfer; M. Hinterberger

2017-01-01

The iron content of the ore used is crucial for the productivity and coke consumption rate in blast furnace pig iron production. Therefore, most iron ore deposits are processed in beneficiation plants to increase the iron content and remove impurities. In several comminution stages, the particle size of the ore is reduced to ensure that the iron oxides are physically liberated from the gangue. Subsequently, physical separation processes are applied to concentrate the iron ore. The fine-graine...

A case study of shrinkage-in place leaching of low grade uranium ore deposit

International Nuclear Information System (INIS)

Ding Dexin; Zhou Guohe

1998-09-01

A case study of shrinkage-in place leaching of low grade uranium ore deposit is dealt with. A test block was selected, and the shrinkage mining method was employed to construct the in place heap for leaching. Blast parameters and operations were carefully tried in order to make sure that the fragment size composition was adequate for leaching. A leaching system was planned and the corresponding leaching parameters were tried, too. The results show that the shrinkage method and the parameters for blasting and leaching are all adequate for the in-situ leaching of the blasted ore. This shrinkage-in place leaching system combines the mining and metallurgy processes into one and produces a lot of profits and could be applicable to many low grade uranium ore deposits which are so hard and compact that they have to be fragmented before being leached

Beneficiation strategy for some low grade ores of strategic metals in India

International Nuclear Information System (INIS)

Krishna Rao, N.

1997-01-01

In developing indigenous resources of strategic metals, beneficiation strategy has a major role to play, particularly where the ores are of low tenor. Presently India imports most of its requirements of metals like tin, tungsten, molybdenum, nickel and cobalt. In all these cases important low grade resources occur in the country. Beneficiation strategy necessary for exploitation of these deposits are discussed based mainly on vast batch and semi plant scale data generated in the Ore Dressing Section of Bhabha Atomic Research Centre. Also discussed is the case of strategic metal uranium where, in certain cases pre-concentration by beneficiation has the potential to make it feasible the exploitation of otherwise difficult to process ore resources. (author)

Microbial leaching of low grade sandstone uranium ores: column leaching studies

International Nuclear Information System (INIS)

Bhatti, T.M.; Malik, K.A.; Khalid, A.M.

1991-01-01

Microbial leaching studies on a low-grade sandstone uranium ore from Baghalchur Ore Deposits, D. G. Khan, Pakistan, containing 0.027 % U/sub 3/O/sub 8/ for extraction of uranium, were conducted in columns. Baghalchur sandstone uranium ore which is alkaline in nature, contained 5.0% calcite [CaCo/sub 3/], 2-3 % Fe/sub 2/O/sub 3/ and pyrite [FeS/sub 2/] less than 0.1 %. The ore amended with sulfur and/or sulfur slag as external energy source was found to leach with indigenous microflora mostly belonging to the genus Thiobacillus which are present in the uranium mine water. Column leaching studies revealed that when the ore was amended with elemental sulfur and irrigated with mine water (pH 3.5) 53 % U/sub 3/O/sub 8/ could be solubilized from it. However, when the natural mine water was used as such (pH 7.4) the solubilization of uranium was decreased to 41 % U/sub 3/O/sub 8/ in 90 days under similar conditions of percolation rate and temperature. The addition of (NH/sub 4/)/sub 2/SO/sub 4/ (3.0 g/L) in mine water was found to enhance the uranium leaching to 70 % U/sub 3/O/sub 8/ from the columns containing ore amended with sulfur slag. (author)

Chlorination separation of uranium, thorium, and radium from low-grade ores

International Nuclear Information System (INIS)

Sastri, V.S.; Perumareddi, J.R.

1995-01-01

Low-temperature chlorination of low-grade uranium ores containing uranium in the 0.02 to 0.06% range, thorium in the 0.036 to 0.12% range, and radium in the 70 to 200 pci/g range resulted in the extraction of >90% of the constituents. The residue left after chlorination was found to be innocuous and suitable for disposal as a waste acceptable to the environment. Use of sodium chloride in the charge was useful in reducing the chlorination temperature and in the formation of nonvolatile anionic chloro complexes of the metal ions in the ore

Preconcentration of low-grade uranium ores with environmentally acceptable tailings, part I

International Nuclear Information System (INIS)

Raicevic, D.; Raicevic, M.; McCarthy, D.R.

1979-08-01

The low-grade ore sample used for this investigation originated from Agnew Lake Mines Limited, Espanola, Ontario. It contained about 1% pyrite and 0.057% uranium, mainly as uranothorite with a small amount of brannerite. Both of these minerals occur in the quartz-sericite matrix of a conglomerate. A preconcentration process has been developed to give a high uranium recovery, reject pyrite, radium and thorium from the ore and produce environmentally acceptable tailings. This process applies flotation in combination with high intensity magnetic separation and gravity concentration

Low grade uranium ores as potential sources of raw material

International Nuclear Information System (INIS)

Venzlaff, H.

1976-01-01

Reports on the uranium requirement and the uranium reserves show that, even if the demand were to be stretched out slightly, the rate of new discoveries of uranium would have to be doubled or even tripled within a few years in order to ensure supply. Despite some spectacular discoveries of large scale deposits in Australia it must be said that only very few truly new uranium provinces have been discovered over the past twenty years. In this situation more attention is now being devoted to low grade uranium depositis, to findings whose concentration does not exceed 1,000 ppm. These deposits contain quantities of uranium many times larger than the deposits that can now be mined at prices up to 30/lb of U 3 O 8 . Even now low grade uranium ore is being mined as a byproduct, with the actual valuable mineral producing most of the income from mining activities. However, if one strikes a balance in this situation, one finds that only part of the requirement can be met in this way. Hence, all possibilities must be exhausted to mine uranium as a byproduct, new techniques of uranium production from low grade ores must be developed, and also conventional prospection must be intensified, if the continuity of supply of the nuclear power stations in the eighties and nineties is to be guaranteed. (orig.) [de

Continued Multicolumns Bioleaching for Low Grade Uranium Ore at a Certain Uranium Deposit

OpenAIRE

Gongxin Chen; Zhanxue Sun; Yajie Liu

2016-01-01

Bioleaching has lots of advantages compared with traditional heap leaching. In industry, bioleaching of uranium is still facing many problems such as site space, high cost of production, and limited industrial facilities. In this paper, a continued column bioleaching system has been established for leaching a certain uranium ore which contains high fluoride. The analysis of chemical composition of ore shows that the grade of uranium is 0.208%, which is lower than that of other deposits. Howev...

Extraction of a Low Grade Zinc Ore using Gravity and Froth Flotation ...

African Journals Online (AJOL)

ADOWIE PERE

ABSTRACT: Extraction of low grade zinc ore found in Gumau- Toro town was carried out using gravity and froth flotation methods. .... And to determine the best separation ..... Wet De, K; Singleton, J.D (2008) Development of a. Viable Process ...

Uranium R and D directed to low-grade ores

International Nuclear Information System (INIS)

Anon.

1976-01-01

The treatment of depleted uranium ores by in-situ leaching and by counterflow ion exchange in the USA is described. In-situ leaching is mainly suitable for sandstone deposits. The research was originally focused on leaching with an acid and with carbonates. Phosphoric acid appears to be a promising leaching agent. The equipment for continuous ion exchange may be used for sludge processing but the application depends on the type of equipment and mineralogy of processed ores. The method is advantageous for lower capital costs and for smooth operation. Ion exchange is also used for uranium extraction from mine waters in the USA as well as in Canada. For example, in Grants, New Mexico, a yield exceeding 90% was reached in mine waters only containing 5 to 7 ppm U 3 O 8 . In the future, the treatment of ores with a low uranium content will require more selective extraction methods in view of the more stringent technical conditions of uranium concentrate processing. (J.P.)

Gold grade of epithermal gold ore at Lamuntet, Brang Rea, West Sumbawa District, West Nusa Tenggara Province, Indonesia

Science.gov (United States)

Ernawati, Rika; Idrus, Arifudin; TBMP, Himawan

2017-06-01

Lamuntet is one of gold ore mining area carried out by the Artisanal Small scale Gold Mining (ASGM) located in West Sumbawa, Indonesia. Most of the miners at this area are not the local miners but also those from other regions. Mineralization of this area is strong identified as low sulfidation epithermal system. There are two blocks of this mining location, namely, Ngelampar block with an area of 0.164 km2 and Song block with an area of 0.067 km2. This study was focused on Ngelampar block. The characteristic of epithermal system is the existence of quartz vein with comb, vuggy, and sugary texture. The aim of this research was to analyze the gold grade and other metals, such as Cu, Ag, Pb, As, Zn, and Hg. The research methods included literature study from previous researches, field work, laboratory work, and interpretation. The literature study was performed on previous researches with similar study area. The field work comprised of direct observation and sampling. Fieldwork was done for a week to obtain gold ore/vein. Sixteen samples were analyzed to obtain the grade of ore/metal. The Hg laboratory analysis was then performed on the six samples with the highest gold grade. Laboratory works were conducted at Intertek Jakarta by using Fire Assay (FA) for gold grade and Atomic Absorption Spectrophotometry (AAS) for Cu, Ag, Pb, As, Zn, and Hg. Results of the analysis showed the range of Au was grade (0.1 ppm - 27.8 ppm), Cu was 26 ppm -1740 ppm, Pb was 101 ppm- >4000 ppm, Zn of 73 ppm- >10,000 ppm, Ag of 3 ppm -185 ppm, As was 150 ppm-6530 ppm, and Hg of 0.08 ppm - 1.89 ppm. L1 and L15 had high grade for all values (Au, Ag, Zn, Cu, As, and Hg). Gold mineralization was formed as electrum because of Ag content is higher than 20%. Associated minerals of the samples in the study area were galena, sphalerite, arsenopyrite, and chalcopyrite which showed the characteristic of rich base metal of Pb, Zn, and Cu at LS epithermal.

Status Report from Canada [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

Thunaes, A [Eldorado Mining and Refining Ltd., Ottawa (Canada)

1967-06-15

The Canadian production of uranium increased in a spectacular manner during the period 1955-1959 from 1000 to 15 500 tons U{sub 3}O{sub 8} per year. Since 1959 the production has declined to the 1966 level of 3900 tons U{sub 3}O{sub 8} per year; stretch-out of contracts and government stockpiling programmes has made the decline gradual, and is maintaining the current rate of production until 1970. Nineteen mills were in operation during the period of peak production but only three are operating today. Ten mills were shut down and dismantled because of exhaustion of ore bodies or because the operation was uneconomical; six mills are maintained in stand-by condition. The total daily capacity of mills in operation or standing by is about 28 000 tons ore, but some of these mills would not be reopened unless an appreciable increase in uranium price occurs. The tide of uranium demand is about ready to turn and prospecting for uranium is very active this year, particularly in the Elliot Lake and Beaverlodge areas. The estimates for uranium demand in 1975-1980 are such that new ore will have to be found and developed, and new treatment plants must be built. The new ore that is found will likely be of lower grade or more expensive to mine than most of the current proven reserves in Canada and the most efficient methods of treatment will be needed to avoid excessive increases in production costs. This seems an opportune time to review Canadian milling of uranium ore, the improvements that have been made and development work towards further improvements.

RECOVERY OF IRON FROM LOW-GRADE HEMATITE ORE USING COAL-BASED DIRECT REDUCTION FOLLOWED BY MAGNETIC SEPARATION

Directory of Open Access Journals (Sweden)

N. Alavifard

2016-09-01

Full Text Available In the present work, iron recovery from a low-grade hematite ore (containing less than 40% iron, which is not applicable in common methods of ironmaking, was studied. Non-coking coal was used as reducing agent. Reduction experiments were performed under various coal to hematite ratios and temperatures. Reduction degree was calculated using the gravimetric method. Reduced samples were subjected to magnetic separation followed by X-ray diffraction analysis. Total iron content, degree of metallization and recovery efficiency in magnetic part were determined by quantitative chemical analysis, which were obtained about 82%, 95% and 64% respectively under optimal conditions. CaO as an additive improved ore reducibility and separation efficiency. The microstructure of reduced samples and final products were analyzed by scanning electron microscopy. Final product with a high degree of metallization can be used in steel making furnaces and charging of blast furnaces which can improve production efficiency and decrease coke usage.

Effect of moisture content on the flowability of crushed ores

Science.gov (United States)

Cabrejos, Francisco

2017-06-01

In many mining and industrial processes where large quantities of non-degrading bulk materials such as crushed ores are handled, silos, hoppers, stockpiles and chutes are widely used because they are economical and reliable (if properly designed and operated). However, they are not free of trouble and may experience flow problems such as arching, ratholing, erratic flow, limited storage capacity, limited discharge flow rate, caking, segregation and/or flooding. Moisture content and fine particles significantly affect the flowability of most ores, increasing their cohesive strength and turning them more prone to these problems. The purpose of this article is to highlight a proven, scientific method that can be utilized to ensure reliable storage, flow and discharge of bulk solids in these equipment based on Jenike's flow-of-solids theory and laboratory testing. Knowledge of the flow properties of the material handled provides a design basis to ensure mass flow, avoid arching and prevent the formation of "ratholes". The effect of an increase in water content of the ore is discussed with experimental results.

Effect of moisture content on the flowability of crushed ores

Directory of Open Access Journals (Sweden)

Cabrejos Francisco

2017-01-01

Full Text Available In many mining and industrial processes where large quantities of non-degrading bulk materials such as crushed ores are handled, silos, hoppers, stockpiles and chutes are widely used because they are economical and reliable (if properly designed and operated. However, they are not free of trouble and may experience flow problems such as arching, ratholing, erratic flow, limited storage capacity, limited discharge flow rate, caking, segregation and/or flooding. Moisture content and fine particles significantly affect the flowability of most ores, increasing their cohesive strength and turning them more prone to these problems. The purpose of this article is to highlight a proven, scientific method that can be utilized to ensure reliable storage, flow and discharge of bulk solids in these equipment based on Jenike’s flow-of-solids theory and laboratory testing. Knowledge of the flow properties of the material handled provides a design basis to ensure mass flow, avoid arching and prevent the formation of “ratholes”. The effect of an increase in water content of the ore is discussed with experimental results.

The impact of new technology on the economics of uranium production from low-grade ores

International Nuclear Information System (INIS)

Simonsen, H.A.; Boydell, D.W.; James, H.E.

1981-01-01

The subject is discussed under the following headings: influence of a depressed market on uranium supply from low-grade ores; potential areas for a reduction in uranium ore processing costs; in-situ leaching (solution mining; heap leaching; resin-in-pulp; solvent-in-pulp; belt filtration; continuous ion exchange; solvent extraction); preconcentration (upgrading of coarse rock; upgrading in the mill; wet high-intensity magnetic separation; flotation); summary and conclusions. (U.K.)

Assessment of (222)Rn emanation from ore body and backfill tailings in low-grade underground uranium mine.

Science.gov (United States)

Mishra, Devi Prasad; Sahu, Patitapaban; Panigrahi, Durga Charan; Jha, Vivekanand; Patnaik, R Lokeswara

2014-02-01

This paper presents a comparative study of (222)Rn emanation from the ore and backfill tailings in an underground uranium mine located at Jaduguda, India. The effects of surface area, porosity, (226)Ra and moisture contents on (222)Rn emanation rate were examined. The study revealed that the bulk porosity of backfill tailings is more than two orders of magnitude than that of the ore. The geometric mean radon emanation rates from the ore body and backfill tailings were found to be 10.01 × 10(-3) and 1.03 Bq m(-2) s(-1), respectively. Significant positive linear correlations between (222)Rn emanation rate and the (226)Ra content of ore and tailings were observed. For normalised (226)Ra content, the (222)Rn emanation rate from tailings was found to be 283 times higher than the ore due to higher bulk porosity and surface area. The relative radon emanation from the tailings with moisture fraction of 0.14 was found to be 2.4 times higher than the oven-dried tailings. The study suggested that the mill tailings used as a backfill material significantly contributes to radon emanation as compared to the ore body itself and the (226)Ra content and bulk porosity are the dominant factors for radon emanation into the mine atmosphere.

Titrimetric determination of uranium in low-grade ores by the ferrous ion-phosphoric acid reduction method

International Nuclear Information System (INIS)

Hitchen, A.; Zechanowitsch, G.

1980-01-01

The modification and extension of the U.S.A.E.C. ferrous ion-phosphoric acid reduction method for the determination of uranium in high-grade or relatively pure material to a method for the determination of uranium with a high accuracy and precision, in ores containing 0.004 to 7% U is described. It is simple, rapid and requires no prior separations from elements that, in other methods, frequently interfere. For sample materials having very high concentrations of interfering elements, a prior concentration step using extraction with tri-n-octylphosphine oxide is described, but it is shown that, for most low-grade ores, this step is unnecessary. (author)

Analysis of Characteristics of Ore about Iron Deposit of Da Hong Mountain in Yun Nan Province

Directory of Open Access Journals (Sweden)

Zhang Yuefeng

2016-01-01

Full Text Available This thesis aims to analyse the deposit characteristics about Da Hong Mountains Iron ore in Yunnan province. The texture and structure, especially the chemical composition, is different in every section of deposit after comparing. Moreover, the content of SiO2 is much higher than general iron ore. However, the content of other noble metals cannot reach the lowest industrial grade. Da Hong Mountains Iron ore has unique features because of metallogenic periods.

Technologies for processing low-grade uranium ores and their relevance to the Indian situation

International Nuclear Information System (INIS)

Murthy, T.K.S.

1991-01-01

The technology for uranium ore processing is well established. Various estimates have shown that on a global basis uranium resources are adequate to meet the forseeable demand. The Indian resources are estimated to be about 60,000 t U. The grade of the ores is low and the individual deposits are small. The nature of the deposits, precarious resources position and relatively small capacity of the mines do not permit the country to take advantage of large throughputs in the mill to achieve substantial cost reduction. However by resorting to as high a scale of milling as the mines would permit, by reducing the loss of solubilised uranium after leaching and by undertaking production of nuclear grade final product at the mill site, significant though not a major, economic benefit can be derived. (author). 2 figs., 3 tabs

A new type on line fast analysis instrument of uranium ore grade

International Nuclear Information System (INIS)

Guo Maojin.

1992-01-01

The instrument is used to analyse the average grade of uranium ore on the belt. Its average analysis speed is about 300 t/h. The physical mechanism of measurement, characteristics, principle of operation and applications in several years are described. The CMOS LSI IC are adopted. The stability, reliability and anti-interference ability are very good

An innovative jet boring mining method available for the high grade uranium ore underground deposits

International Nuclear Information System (INIS)

Narcy, J.L.

1996-01-01

An innovative mining method, based on the capability of a high pressure water jet to desaggregate rock, has been conceived and tested with success at the highest grade uranium ore deposit in the world, the Cigar Lake deposit in Saskatchewan, Canada. 113 tonnes of ore at 13% U were mined out by a new jet-boring mining method operated on a semi-industrial basis, in 1992 during the test mining program of Cigar Lake Project. (author). 9 figs

Chlorine/chloride based processes for uranium ores

International Nuclear Information System (INIS)

1980-11-01

The CE Lummus Minerals Division was commissioned by The Department of Supply and Services to develop order-of-magnitude capital and operating cost estimates for chlorine/chloride-based processes for uranium ores. The processes are designed to remove substantially all radioactive consituents from the ores to render the waste products harmless. Two processes were selected, one for a typical low grade ore (2 lb. U 3 O 8 /ton ore) and one for a high grade ore (50 lbs U 3 O 8 /ton). For the low grade ore a hydrochloric acid leaching process was chosen. For high grade ore, a more complex process, including gaseous chlorination, was selected. Capital cost estimates were compiled from information obtained from vendors for the specified equipment. Building cost estimates and the piping, electrical and instrumentation costs were developed from the plant layout. Utility diagrams and mass balances were used for estimating utilities and consumables. Detailed descriptions of the bases for capital and operating cost estimates are given

Hydrogen Reduction of Hematite Ore Fines to Magnetite Ore Fines at Low Temperatures

Directory of Open Access Journals (Sweden)

Wenguang Du

2017-01-01

Full Text Available Surplus coke oven gases (COGs and low grade hematite ores are abundant in Shanxi, China. Our group proposes a new process that could simultaneously enrich CH4 from COG and produce separated magnetite from low grade hematite. In this work, low-temperature hydrogen reduction of hematite ore fines was performed in a fixed-bed reactor with a stirring apparatus, and a laboratory Davis magnetic tube was used for the magnetic separation of the resulting magnetite ore fines. The properties of the raw hematite ore, reduced products, and magnetic concentrate were analyzed and characterized by a chemical analysis method, X-ray diffraction, optical microscopy, and scanning electron microscopy. The experimental results indicated that, at temperatures lower than 400°C, the rate of reduction of the hematite ore fines was controlled by the interfacial reaction on the core surface. However, at temperatures higher than 450°C, the reaction was controlled by product layer diffusion. With increasing reduction temperature, the average utilization of hydrogen initially increased and tended to a constant value thereafter. The conversion of Fe2O3 in the hematite ore played an important role in the total iron recovery and grade of the concentrate. The grade of the concentrate decreased, whereas the total iron recovery increased with the increasing Fe2O3 conversion.

Biomineral processing of high apatite containing low-grade indian uranium ore

International Nuclear Information System (INIS)

Abhilash; Mehta, K.D.; Pandey, B.D.; Ray, L.; Tamrakar, P.K.

2010-01-01

Microbial species isolated from source mine water, primarily an enriched culture of Acidithiobacillus ferrooxidans was employed for bio-leaching of uranium from a low-grade apatite rich uranium ore of Narwapahar Mines, India while varying pH, pulp density (PD), particle size, etc. The ore (0.047% U_3O_8), though of Singhbhum area (richest deposit of uranium ores in India), due to presence of some refractory minerals and high apatite (5%) causes a maximum 78% recovery through conventional processing. Bioleaching experiments were carried out by varying pH at 35"oC using 20%(w/v) PD and <76μm size particles resulting in 83.5% and 78% uranium bio-recovery at 1.7 and 2.0 pH in 40 days as against maximum recovery of 46% and 41% metal in control experiments respectively. Finer size (<45μm) ore fractions exhibited higher uranium dissolution (96%) in 40 days at 10% (w/v) pulp density (PD), 1.7 pH and 35"oC. On increasing the pulp density from 10% to 20% under the same conditions, the biorecovery of uranium fell down from 96% to 82%. The higher uranium dissolution during bioleaching at 1.7 pH with the fine size particles (<45μm) can be correlated with increase in redox potential from 598 mV to 708 mV and the corresponding variation of Fe(III) ion concentration in 40 days. (author)

Biomineral processing of high apatite containing low-grade indian uranium ore

Energy Technology Data Exchange (ETDEWEB)

Abhilash; Mehta, K.D.; Pandey, B.D., E-mail: biometnml@gmail.com [National Metallurgical Laboratory (CSIR), Jamshedpur (India); Ray, L. [Jadavpur Univ., FTBE Dept., Kolkata (India); Tamrakar, P.K. [Uranium Corp. of India Limited, CR& D Dept., Jaduguda (India)

2010-07-01

Microbial species isolated from source mine water, primarily an enriched culture of Acidithiobacillus ferrooxidans was employed for bio-leaching of uranium from a low-grade apatite rich uranium ore of Narwapahar Mines, India while varying pH, pulp density (PD), particle size, etc. The ore (0.047% U{sub 3}O{sub 8}), though of Singhbhum area (richest deposit of uranium ores in India), due to presence of some refractory minerals and high apatite (5%) causes a maximum 78% recovery through conventional processing. Bioleaching experiments were carried out by varying pH at 35{sup o}C using 20%(w/v) PD and <76μm size particles resulting in 83.5% and 78% uranium bio-recovery at 1.7 and 2.0 pH in 40 days as against maximum recovery of 46% and 41% metal in control experiments respectively. Finer size (<45μm) ore fractions exhibited higher uranium dissolution (96%) in 40 days at 10% (w/v) pulp density (PD), 1.7 pH and 35{sup o}C. On increasing the pulp density from 10% to 20% under the same conditions, the biorecovery of uranium fell down from 96% to 82%. The higher uranium dissolution during bioleaching at 1.7 pH with the fine size particles (<45μm) can be correlated with increase in redox potential from 598 mV to 708 mV and the corresponding variation of Fe(III) ion concentration in 40 days. (author)

Heap-leaching of low-grade uranium ore at SOMAIR: from laboratory tests to production of 700 tonnes U per year

Energy Technology Data Exchange (ETDEWEB)

Durupt, N.; Blanvillain, J.J., E-mail: nicolas.durupt@areva.com [AREVA NC, Service d' Etudes de Procedes et d' Analyses (SEPA), Bessines sur Gartempe (France)

2010-07-01

In 2006, SOMAIR decided to increase the uranium production by 50% using heap leaching for the treatment of low grade ores. These ores, which come from different ores with various properties, have been studied in four steps: Lab tests: to compare the ores (characterization, acid consumptions, recovery); Column tests on an average sample: to define significant parameters for a feasibility study; Column tests on specific samples: to optimize recovery for each ore and identify problems of percolation due to the clays; and, Pilot tests in large boxes (stalls): to validate process parameters. Uranium production by heap leaching started commercially in July 2009. (author)

Studies on the recovery of uranium from low-grade ores in India

International Nuclear Information System (INIS)

Jayaram, K.M.V.; Dwivedy, K.K.; Deshpande, A.S.; Ramachar, T.M.

1976-01-01

Investigations were carried out to utilize the available para-marginal and low-grade ores - chlorite schists, amphibolites, carbonate ores, clays and quartzites - analysing between 0.027 and 0.08% U 3 O 8 . In addition, tests were undertaken on the technical and economic feasibility of recovering uranium as a byproduct from the copper flotation tailings and phosphorites. Heap and bacterial leaching tests were conducted on quartz-chlorite schists from the Singhbhum district, Bihar, analysing about 0.03% U 3 O 8 . Studies also showed that the ores harbour active Ferrobacillus ferrooxidans. Studies on 10-mesh samples of amphibolites from Inderwa, Bihar, (0.08% U 3 O 8 ) showed that only 32.8% recovery could be obtained by wet tabling and 85% by agitation leaching, while static leaching tests yielded 81% recovery in 24 hours of contact time. Similar tests on calcareous phyllites (0.05% U 3 O 8 ) with 30 kg/t Na 2 CO 3 and 8 kg/t NaHCO 3 yielded 86% uranium leachability at ambient temperature. Biogenic uraniferous clay from Udaisagar (0.029% U 3 O 8 ) yielded 43.3% uranium recovery using 1000 l/t of neutral water for 6 h. Percolation leaching tests were conducted with hard quartzites (0.06% U 3 O 8 ), and the results showed that 81% uranium could be recovered in 24 days. Although preliminary ore dressing studies on tailings obtained from the copper flotation (0.013% U 3 O 8 ) at Surda yielded a concentrate analysing 0.063% U 3 O 8 at 66% recovery, recent tests on the tailings from the copper concentrator indicated only 48% recovery at a grade of 0.112% owing to decrease in the feed grade. Studies on the utilization of large-capacity gravity machines and selective mining of uranium-rich copper lodes may render this source economic. Preliminary studies on a phosphorite sample containing 22.0% P 2 O 5 and 0.04% U 3 O 8 from the Mussorie area in Uttar Pradesh on calcination followed by scrubbing yielded a sand enriched in P 2 O 5 values (33.7% P 2 O 5 at 92.5% recovery) but

A study on the upgrading by physical means of low grade uranium ore from Phu Wiang District

International Nuclear Information System (INIS)

Wihokratna, W.

1980-01-01

The purpose of this thesis is to upgrade the uranium ore at Phu Wiang district. Because of the fine grains and high degree of dissemination of uranium in ores, resulting practically complete envelopment of the uranium minerals by the gangue minerals, the ore must first undergo digestion in order to reveal the uranium minerals. After digestion, sodium hydroxide of 0.05 normal was added to the ore and the mixture was fed into the agitator provided with baffles and two specially designed propellers. Due to the 'Push - Pull' motion of the propellers a zone of specially high turbulence was created between them. Also in this region higher concentration of uranium is revealed and the high concentrated uranium ore was regularly stripped off for further analysis. It was found that by using mineral of grain size of 100 mesh and 0.0187% of uranium content a concentration up to 0.063% uranium content (an upgrading better than by a factor of three times) was achieved with the above method. The uranium content was analyzed with 3'' x 3'' NaI (Tl) detector and 1024 channels MCA

Uranium ore deposits: geology and processing implications

International Nuclear Information System (INIS)

Belyk, C.L.

2010-01-01

There are fifteen accepted types of uranium ore deposits and at least forty subtypes readily identified around the world. Each deposit type has a unique set of geological characteristics which may also result in unique processing implications. Primary uranium production in the past decade has predominantly come from only a few of these deposit types including: unconformity, sandstone, calcrete, intrusive, breccia complex and volcanic ones. Processing implications can vary widely between and within the different geological models. Some key characteristics of uranium deposits that may have processing implications include: ore grade, uranium and gangue mineralogy, ore hardness, porosity, uranium mineral morphology and carbon content. Processing difficulties may occur as a result of one or more of these characteristics. In order to meet future uranium demand, it is imperative that innovative processing approaches and new technological advances be developed in order that many of the marginally economic traditional and uneconomic non-traditional uranium ore deposits can be exploited. (author)

Research of geological technologic condition in laboratory about the ore of 501 deposits

International Nuclear Information System (INIS)

Ma Guoxiang; Yu Baoli; Gao Yuyou; Li Changhua

2009-01-01

501 deposits of uranium ore grade is 0.052%. The radio of U +6 /U 4+ is 1.7-4.6. there is less content of sarbonate, such as sulfide and organic matter which disservice baptist uranium geological process, and the uranium and oxygen with a high level in the water of seam. The content of [HCO 3 ] - is lower. By conducting the static leaching test, the important technical parameters of uranium ore extraction are determined: with 7.91 g/L H 2 SO 4 , to soak uranium ore which the grade is between 0.007% and 0.216% for 48 hours, the uranium extraction rate of 64.69-99.17%, and extract uranium concentration 9.51-427.6 mg/L; the formula of infusion solution is obtained by using percolation leaching test: 6-8 g/L H 2 SO 4 , the rate of uranium extraction is 95.71%-96.33%, an average of leaching solution uranium concentration of 88.33-111.32 mg/L, leaching liquid-solid ratio of 4.46-5.66, ore tons of sulfuric acid consumption to 27.58-29.83 kg/t, extraction of uranium 1 kg of sulfuric acid consumption to 55.17-60.06 kg. That indicate the geological technologic conditions which the leaching of uranium ore deposits is better. (authors)

Mutualism between autotrophic and heterophic bacteria in leaching of low grade ores

International Nuclear Information System (INIS)

Khalid, Z.M.; Naeveke, R.

1991-01-01

During solubilization processes of low grade sulphidic ores, the auto trophic bacteria oxidize reduced sulphur compounds and ferrous iron to sulphates and ferric iron respectively. The ore leaching bio topes are not only colonized by auto trophic bacteria (Thiobacillus spp., Leptospirillum ferro oxidans and sulfolobus sp.) but the heterotrophic microorganisms, including bacteria and fungi of various species are also found in these habitats. The autotrophs, in addition to energy metabolism, also produce organic compounds which in excess amount inhibit their growth. Through the utilization of such compounds and also through the production of carbon dioxide and ammonia, these heterotorphs can help bio leaching processes. Effect of one of the heterotrophs; methylobacterium sp., a nitrogen scavenger, found in as association with the thio bacilli in one of the leaching bio tope in Germany was studied in leaching of a carbonate bearing complex (containing copper, iron, zinc and lead) sulphidic ore, in shake flask studies. T. ferro oxidans (Strain F-40) reported to be non nitrogen fixer and strain F-41, a nitrogen fixing thiobacillus were studied for leachability behaviour alone and in combination with T. thio oxidans (lacking nitrogen fixing ability) using media with and without added ammonium nitrogen. In addition the effect of methylobacterium sp. (alt-25) was also tested with the afore mentioned combinations. Nitrogen fixation by T. ferro oxidans did not suffice the nitrogen requirement and the leaching system in laboratory needed addition of nitrogen. The heterotrophic nitrogen scavenger also did not have a positive influence in nitrogen limited system. In case where ammonium nitrogen was also provided in the media, this heterotroph had a negative in own growth and leaving lesser amount available for thio bacilli. This high amount of acid is a limiting factor in bio leaching of high carbonate uranium ores. Uranium ore ecosystems have also been found to contain

Discussion on uranium ore-formation age in Xiazhuang ore-field, northern Guangdong

International Nuclear Information System (INIS)

Wu Lieqin; Tan Zhengzhong; Liu Ruzhou; Huang Guolong

2003-01-01

There exist two genetic types of granite-type uranium deposits, i.e. the early-stage one, and the late-stage one. The early-stage uranium deposits are characterized by ore-formation ages of 122-138 Ma, and are high-grade uranium deposits of postmagmatic hydrothermal origin. The late-stage uranium deposits have ore-formation ages of 54-96 Ma. They mostly are low-grade uranium deposits, and of hydrothermal-regeneration origin with the uranium source derived from the mobilization of consolidated rocks. The early-stage uranium deposits should be the main target of further prospecting for high-grade uranium deposits in the region

A Multistage Sulphidisation Flotation Procedure for a Low Grade Malachite Copper Ore

OpenAIRE

Tebogo P. Phetla; Edison Muzenda

2010-01-01

This study was carried out to develop a flotation procedure for an oxide copper ore from a Region in Central Africa for producing an 18% copper concentrate for downstream processing at maximum recovery from a 4% copper feed grade. The copper recoveries achieved from the test work were less than 50% despite changes in reagent conditions (multistage sulphidisation, use of RCA emulsion and mixture, use of AM 2, etc). The poor recoveries were attributed to the mineralogy of t...

Petrographic-mineralogical characterization with liberation grade, X ray and chemical diffractometry in ore samples of Itataia-CE mine

International Nuclear Information System (INIS)

Salas, H.T.

1985-01-01

From samples collected by geologists in several points of G2 and G3 gallery of Itataia Uranium Phosphate mine, intended to get knowledge about several lithologic types of ores, mainly its alteration grades. Petrographic-mineralogical studies, liberation grade calculation of apatite, X-ray diffractometry analysis and dosage of oxydes by X-ray fluorencence are executed. (C.M.) [pt

Comprehensive recovery of gold and base-metal sulfide minerals from a low-grade refractory ore

Science.gov (United States)

Li, Wen-juan; Liu, Shuang; Song, Yong-sheng; Wen, Jian-kang; Zhou, Gui-ying; Chen, Yong

2016-12-01

The comprehensive recovery of small amounts of valuable minerals such as gold and base-metal sulfide minerals from a low-grade refractory ore was investigated. The following treatment strategy was applied to a sample of this ore: gold flotation-gold concentrate leaching-lead and zinc flotation from the gold concentrate leaching residue. Closed-circuit trials of gold flotation yielded a gold concentrate that assayed at 40.23 g·t-1 Au with a recovery of 86.25%. The gold concentrate leaching rate was 98.76%. Two variants of lead-zinc flotation from the residue—preferential flotation of lead and zinc and bulk flotation of lead and zinc—were tested using the middling processing method. Foam from the reflotation was returned to the lead rougher flotation or lead-zinc bulk flotation, whereas middlings from reflotation were discarded. Sulfur concentrate was a byproduct. The combined strategy of flotation, leaching, and flotation is recommended for the treatment of this kind of ore.

Pb(II), Cd(II) and Zn(II) adsorption on low grade manganese ore ...

African Journals Online (AJOL)

Low grade manganese ore (LMO) of Orissa containing 58.37% SiO2, 25.05% MnO2, 8.8% Al2O3, and 5.03% Fe2O3 as the main constituents was taken to study its adsorption behaviour for Pb(II), Cd(II) and Zn(II) from aqueous solutions. The XRD studies showed the crystalline phases to be quartz, ß-MnO2, d-MnO2 and ...

Ore-processing technology and the uranium supply outlook

International Nuclear Information System (INIS)

James, H.E.; Simonsen, H.A.

1978-01-01

The subject is covered in sections, as follows: the resource base (uranium content of rocks, regional distribution of Western World uranium); ore types (distribution of Western World uranium, by ore types, response to ore-processing); constraints on expansion in traditional uranium areas (defined for this paper as the sandstone deposits of the U.S.A. and the quartz-pebble conglomerates of the Witwatersrand and Elliot Bay areas, all other deposits being referred to as new uranium areas). Sections then follow dealing in detail with the processing of deposits in U.S.A., South Africa, Canada, Niger, Australia, South West Africa, Greenland. More general sections follow on: shale, lignite and coal deposits, calcrete deposits. Finally, there are sections on: uranium as a by-product; uranium from very low-grade resources; constraints on expansion rate for production facilities. (U.K.)

Biocatalytic and chemical leaching of a low-grade nickel laterite ore

Science.gov (United States)

Ciftci, Hasan; Atik, Suleyman; Gurbuz, Fatma

2018-04-01

Nickel and cobalt recovery from a low-grade nickel laterite ore, supplied from Çaldağ deposit (Manisa, Turkey) were investigated by bio and chemical leaching processes. The fungus, Aspergillus niger was used for biocatalytic leaching experiments. The effects of parameters (solid ratio and sucrose concentration) on the biocatalytic leaching of the ore were initially tested in flasks to obtain the optimum conditions for the A. niger. Then chemical leaching was applied as a comparison to bioleaching, using organic acids (citric, oxalic, acetic and gluconic acids) as well as a mixture of acids. According the results, the maximum dissolution yield of nickel, cobalt and iron were detected respectively as 95.3%, 74.3% and 50.0% by biocatalytic processes which containing 25% (w/v) sucrose and 1% (w/v) solids. The increase in the solid ratio adversely influenced the biocatalytic activity of A. niger. Finally, further tests in reactors (v = 1 and 10 L) were performed using the optimum conditions from the flask tests. The difference in metals recovery between biocatalytic and chemical leaching was significantly important. Bioleaching produced higher Ni and Co extractions (34.3-75.6%) than chemical process.

Determination of uranium content in phosphate ores using different measurement techniques

Directory of Open Access Journals (Sweden)

Mohammad A. Al-Eshaikh

2016-01-01

Full Text Available The most important unconventional source of uranium is found in phosphate deposits; unfortunately, nowadays its exploitation is limited by economic constraints. The uranium concentrations in phosphate ores in the world vary regionally and most countries with large phosphate deposits have either plant in operation to extract uranium or are at the stage of pilot extraction plants. The aim of this investigation is to evaluate uranium content in the Saudi phosphate ores for, at least, two reasons: firstly, upgrading the phosphate quality by removing the uranium content in order to reduce the radioactivity in the fertilizer products. Secondly, getting benefit from the extracted uranium for its domestic use as a fuel in nuclear power and desalination plants. The results of this study show that the uranium concentration in Saudi phosphate rocks is relatively low (less than 100 ppm, which is not economically encouraging for its direct extraction. However, its extraction as a byproduct from the phosphoric acid, which will have higher concentration could be quite promising and worth exploiting.

Modelling a uranium ore bioleaching process

International Nuclear Information System (INIS)

Chien, D.C.H.; Douglas, P.L.; Herman, D.H.; Marchbank, A.

1990-01-01

A dynamic simulation model for the bioleaching of uranium ore in a stope leaching process has been developed. The model incorporates design and operating conditions, reaction kinetics enhanced by Thiobacillus ferroxidans present in the leaching solution and transport properties. Model predictions agree well with experimental data with an average deviation of about ± 3%. The model is sensitive to small errors in the estimates of fragment size and ore grade. Because accurate estimates are difficult to obtain a parameter estimation approach was developed to update the value of fragment size and ore grade using on-line plant information

Preconcentration of a low grade uranium ore in CPDU and laboratory investigation to optimize the dewatering conditions of the preconcentration products

International Nuclear Information System (INIS)

Cristovici, M.A.; Berry, T.F.; Raicevic, M.M.; Brady, E.L.; Bredin, E.L.; Leigh, G.W.; Rouleau, J.P.

1982-04-01

A process consisting of pyrite flotation and magnetic concentration of radionuclides was developed by CANMET over several years, to preconcentrate low grade uranium ores prior to leaching. When the economics of the preconcentration-leaching technology was compared with the leaching of the entire ore after pyrite flotation (Base Case variant), the preconcentration method appeared to be economically less advantageous than expected, due to the high cost of dewatering the preconcentration products. Further investigations examined in-depth the metallurgy and dewatering of the two variants: preconcentration and base case. A typical low grade uranium ore from Elliot Lake area was used. The metallurgy was compared based on data from continuous operation (CPDU). In the preconcentration variant the amount of ore directed to leaching was reduced to more than one third of that processed in the base case, while the radionuclide concentration became more than three times higher. However, by preconcentration 7% of the uranium was lost before leaching. Systematic laboratory-scale settling and filter tests optimized the dewatering conditions of the preconcentration technology to the extent that rates similar to those of the base case were obtained

The Application of Artificial Neural Networks to Ore Reserve Estimation at Choghart Iron Ore Deposit

Directory of Open Access Journals (Sweden)

Seyyed Ali Nezamolhosseini

2017-01-01

Full Text Available Geo-statistical methods for reserve estimation are difficult to use when stationary conditions are not satisfied. Artificial Neural Networks (ANNs provide an alternative to geo-statistical techniques while considerably reducing the processing time required for development and application. In this paper the ANNs was applied to the Choghart iron ore deposit in Yazd province of Iran. Initially, an optimum Multi Layer Perceptron (MLP was constructed to estimate the Fe grade within orebody using the whole ore data of the deposit. Sensitivity analysis was applied for a number of hidden layers and neurons, different types of activation functions and learning rules. Optimal architectures for iron grade estimation were 3-20-10-1. In order to improve the network performance, the deposit was divided into four homogenous zones. Subsequently, all sensitivity analyses were carried out on each zone.  Finally, a different optimum network was trained and Fe was estimated separately for each zone. Comparison of correlation coefficient (R and least mean squared error (MSE showed that the ANNs performed on four homogenous zones were far better than the nets applied to the overall ore body. Therefore, these optimized neural networks were used to estimate the distribution of iron grades and the iron resource in Choghart deposit. As a result of applying ANNs, the tonnage of ore for Choghart deposit is approximately estimated at 135.8 million tones with average grade of Fe at 56.14 percent. Results of reserve estimation using ANNs showed a good agreement with the geo-statistical methods applied to this ore body in another work.

Distribution of the ore elements in ore bodies of the Zapolyarnoe field (Kola Peninsula

Directory of Open Access Journals (Sweden)

D. V. Taymasov

2017-12-01

Full Text Available The author conducted studies of the chemical zonality of ore deposits of all types for the sulfide-copper-nickel deposit Zapolyarnoe. Within the deposit of sulfide-copper-nickel ores Zapolyarnoe are the following industrial types of ores: rich interspersed ores, which are interspersed mineralization in peridotites; brecciated ores formed by detrital material; poor interspersed ores characterized by vein-interspersed mineralization; solid ores in a form of massive sulphide emissions. This work is based on operational and detailed exploration data. The author sorted samples according to the types of ores. Using the results, the author derived regression lines and their formulas to rectilinear dependencies. Analysis of the graphs showed that for all types of ores the dependences of copper and cobalt content on nickel content are direct, but at that, in thick-interspersed and brecciated types they are similar, and in scattered-interspersed they differ significantly. It becomes clear that correlation of copper and nickel in ore body depends on the scattered-interspersed ores, whereas the correlation of cobalt and nickel is determined mainly by thick-interspersed and brecciated ores. Dependencies between nickel, copper and cobalt in ores change when concentration of nickel in the ore changes. The graphs also show that the ratio of Ni/Cu in breccias and scattered-interspersed ores, as well as in near-ore metaperidotites, is almost constant at different nickel concentrations, on average 2:1.5 and 1, respectively. Thick- interspersed ores show the tendency towards an increase in the ratio with an increase in nickel content. The Ni/Co ratio increases with an increase of Ni concentration in all types of ores. In rich ores, growth occurs along a stepped curve, and in breccias – rectilinearly. Thus, the analysis of distribution of ore elements in ore bodies indicates a complex heterogeneous composition of sulphide mineralizations in different types of ores

X-ray fluorescence diffractionless analyzer for determining light element content in iron ore mixtures

International Nuclear Information System (INIS)

Yuksa, L.K.; Kochmola, N.M.; Bondarenko, V.P.; Bogdanov, V.K.

1986-01-01

Diffractionless X-ray fluorescence analyzer for detecting calcium oxide and silicon dioxide contents in dry iron ore materials has been developed. The analyzer includes a charging unit, sample-conveying device, spectrometric units for detecting calcium and silicon, computing racks and sample-removing device. Results of calcium oxide and silicon dioxide analyses in iron ore mixtures are presented. Errors are evaluated. It is shown that the analyzer provides high accuracy of one-time determinations, as well as reading constancy for a long time

Enhancement of Au-Ag-Te contents in tellurium-bearing ore minerals via bioleaching

Science.gov (United States)

Choi, Nag-Choul; Cho, Kang Hee; Kim, Bong Ju; Lee, Soonjae; Park, Cheon Young

2018-03-01

The purpose of this study was to enhance the content of valuable metals, such as Au, Ag, and Te, in tellurium-bearing minerals via bioleaching. The ore samples composed of invisible Au and Au paragenesis minerals (such as pyrite, chalcopyrite, sphalerite and galena) in combination with tellurium-bearing minerals (hessite, sylvanite and Tellurobismuthite) were studied. Indigenous microbes from mine drainage were isolated and identified as Acidithiobacillus ferrooxidans, which were used in bioleaching after adaption to copper. The effect of the microbial adaption on the bioleaching performance was then compared with the results produced by the non-adaptive process. The microbial adaption enhanced the Au-Ag-Te contents in biological leaching of tellurium-bearing ore minerals. This suggests that bioleaching with adapted microbes can be used both as a pretreatment and in the main recovery processes of valuable metals.

Effects of Sodium Citrate on the Ammonium Sulfate Recycled Leaching of Low-Grade Zinc Oxide Ores

Science.gov (United States)

Yang, Kun; Li, Shi-wei; Zhang, Li-bo; Peng, Jin-hui; Ma, Ai-yuan; Wang, Bao-bao

2016-03-01

The effects of sodium citrate on ammonium sulfate recycled leaching of low-grade zinc oxide ores were studied. By applying various kinds of detection and analysis techniques such as chemical composition analysis, chemical phase method, scanning electron microscopy and energy dispersive spectrum (SEM/EDS), X-ray diffraction (XRD) and Fourier-transforming infrared spectrum (FT-IR), zinc raw ore, its leaching slag and the functional mechanism of sodium citrate were investigated. Based on a comprehensive analysis, it can be concluded that in contrast to hemimorphite (Zn4Si2O7(OH)2 · H2O), amorphous smithsonite (ZnCO3) and zinc silicate (Zn2SiO4) prove to be refractory phases under ammonium sulfate leaching, while sodium citrate has a better chelating action with the refractory phases, resulting in a higher zinc leaching rate. Under conditions of [NH3]/[NH3]T molar ratio being 0.5, [NH3]T being 7.5 mol/L, [Na3C6H5O7] being 0.2 mol/L, S/L ratio being 1:5, temperature being 303 K, holding time being 1 h in each of the two stages, and stirring rate being 300 rpm, the leaching rate of zinc reached 93.4%. In this article, sulfate ammonium recycled technology also reveals its unique advantage in processing low-grade zinc oxide ores accompanied by high silicon and high alkaline gangue.

Effect of moisture content on the flowability of crushed ores

OpenAIRE

Cabrejos Francisco

2017-01-01

In many mining and industrial processes where large quantities of non-degrading bulk materials such as crushed ores are handled, silos, hoppers, stockpiles and chutes are widely used because they are economical and reliable (if properly designed and operated). However, they are not free of trouble and may experience flow problems such as arching, ratholing, erratic flow, limited storage capacity, limited discharge flow rate, caking, segregation and/or flooding. Moisture content and fine parti...

Estimation grade of uranium from drill hole gamma logs

International Nuclear Information System (INIS)

Juliao, B.

1986-01-01

Radiometric grade of uranium deposits can be determined from drill hole gamma logs. The calculation of uranium oxide content can be obtained with good precision when the uranium ore is in radioactive equilibrium, containing only a small amount of thorium and no interference of potassium. This is the case of uranium ore from the Lagoa Real Uranium Province presented in this paper. The radioactive disequilibrium study in this province were made working over nine hundred samples analised with this special purpose in the CDTN-NUCLEBRAS laboratories. The data obtained indicated that the uranium in the ore is in perfect equilibrium with their daughter gamma emitters. Futhermore, the amount of Th and K is of no significance, so that the gamma counting represents exactly the uranium content of the ore. (author) [pt

Beneficiation and agglomeration of manganese ore fines (an area so important and yet so ignored)

Science.gov (United States)

Sane, R.

2018-01-01

. Sinters have already been proved to bring enormous technical benefits in smelting operation. However small mine owners find it practically impossible to set up a small beneficiation and/or sintering unit at mine site. Recent advances in dry or pneumatic separation which depends on density difference between valuable mineral and gangue/waste rock, are proving to be advantageous & effective because of its small capacity. Capacity is 5 T/hr or 10 T/hr. When applied to low grade high silica Iron ores Iron content has been found to be enhanced by 8 to 10 % from 48% to 58 %, with overall wt. recovery of 60 to 70 %. Recently this technique was applied to low grade siliceous Mn ore with very encouraging results. Mn content has been found to be enhanced from 25 +/- 2 % to 37 +/- 2 % and with 50 to 65% wt. recovery. Size of feed is restricted to (i) 6 to 25 mm and (ii) 2 to 6 mm. Due to Modular design it is possible to put up units from 50 TPD to 800 TPD capacity.

Status report from USSR [Processing of Low-Grade Uranium Ores]; Doklad o sostoyanii voprosa v SSSR

Energy Technology Data Exchange (ETDEWEB)

Zefirov, A P [Gosudarstvennyj Komitet Po Ispol' zovaniyu Atomnoj Ehnergii SSSR, Moskva, Union of Soviet Socialist Republics (Russian Federation)

1967-06-15

The uranium industry for processing poor uranium ores in the USSR was established in recent years. As a result of research work institutions and enterprises in the development of this industry was provided by rapid technological advances that allowed dramatically increased productivity, reduced consumption of reagents, simplified process flow diagrams, and reduced production costs. At present, the basis for uranium industry, including and poor uranium ore deposits in the USSR are with different content valuable components (uranium, phosphorus, molybdenum, rare earth elements, thorium, iron, .. .)

Magnetic concentration of iron-titanium ore with vanadium concentrate from campo Alegre de Lourdes - Bahia, Brazil

International Nuclear Information System (INIS)

Delgado, O.; Silva, F.T. da; Ogasawara, T.; Soares, G.F.

1988-01-01

The feasibility studies of magnetic concentration of the Campo Alegre de Lourdes ore were carried out, trying to obtain a maximum recovery of vanadium. As a consequence of the complex nature of the ore, mainly due to the presence of ilmenite as a exolutions in the interior of hematite/martite particles, it was not possible to separate the hematite-ilmenite eficiently, wich would be necessary for obtaining a high grade vanadium concentrate with low titanium content. (author) [pt

Biohydrometallurgy and membrane technology for resource recovery from low-grade ores and mining residuals

International Nuclear Information System (INIS)

Werner, Arite; Meschke, Katja; Bohlke, Kevin; Haseneder, Roland; Daus, Birgit; Repke, Jens-Uwe

2017-01-01

The recovery of strategic elements from secondary mineral resources and low grade ores is of increasing relevance, due to a changing global market as well as for reasons of sustainability. The present article shows the potential of biohydrometallurgy as an efficient technology for mobilization of metals from secondary mineral resources. Furthermore, the application of membrane separation as a successful technique for the recovery of metals from bioleaching solutions is presented. These issues are discussed within the scope of recent research projects.

Utilisation of iron ore tailings as aggregates in concrete

Directory of Open Access Journals (Sweden)

Francis Atta Kuranchie

2015-12-01

Full Text Available Sustainable handling of iron ore tailings is of prime concern to all stakeholders who are into iron ore mining. This study seeks to add value to the tailings by utilising them as a replacement for aggregates in concrete. A concrete mix of grade 40 MPa was prepared in the laboratory with water–cement ratio of 0.5. The concrete were cured for 1, 2, 3, 7, 14 and 28 days. The properties of the concrete such as workability, durability, density, compressive strength and indirect tensile strength were tested. A controlled mix of concrete was also prepared in similar way using conventional materials and the results were compared with the tailings concrete. It was found that the iron ore tailings may be utilised for complete replacement for conventional aggregates in concrete. The iron ore tailings aggregates concrete exhibited a good mechanical strength and even in the case of compressive strength, there was an improvement of 11.56% over conventional aggregates concrete. The indirect tensile strength did not improve against the control mix due high content of fines in the tailings aggregates but showed 4.8% improvement compared with the previous study where the conventional fine aggregates was partially replaced by 20% with iron ore tailings.

High-grade iron ore at Windarling, Yilgarn Craton: a product of syn-orogenic deformation, hypogene hydrothermal alteration and supergene modification in an Archean BIF-basalt lithostratigraphy

Science.gov (United States)

Angerer, Thomas; Hagemann, Steffen G.; Danyushevsky, Leonid

2013-08-01

Banded iron formation (BIF)-hosted iron ore deposits in the Windarling Range are located in the lower greenstone succession of the Marda-Diemals greenstone belt, Southern Cross domain, Yilgarn Craton and constitute a total hematite-martite-goethite ore resource of minimum 52 Mt at 60 wt.% Fe (0.07 P). Banded iron formation is interlayered with high-Mg basalts at Windarling and precipitated during episodes of volcanic quiescence. Trace element content and the rare earth element (REE) ratios Y/Ho (42 to 45), Sm/Yb (1.5), together with positive La and Gd anomalies in `least-altered' hematite-magnetite-metachert-BIF indicate the precipitation from Archean seawater that was fertilised by hydrothermal vent fluids with a basaltic HREE-Y signature. Hypogene iron ore in sub-greenschist facies metamorphosed BIF formed during three distinct stages: ore stage 1 was a syn- to post-metamorphic, syn-D1, Fe-Ca-Mg-Ni-Co-P-REE metasomatism that produced local Ni-REE-rich Fe-dolomite-magnetite alteration in BIF. Hydrothermal alteration was induced by hot fluid flow controlled by brittle-ductile reactivation of BIF-basalt margins and crosscutting D1 faults. The Ni-Co-rich content of dolomite and a shift in REE ratios in carbonate-altered BIF towards Archean mafic rock signature (Y/Ho to 31 to 40, Sm/Yb to 1 to 2 and Gd/Gd* to 1.2 to 1.4) suggest that high-Mg basalts in the Windarling Range were the primary source of introduced metals. During ore stage 2, a syn-deformational and likely acidic and oxidised fluid flow along BIF-basalt margins and within D1 faults leached carbonate and precipitated lepidoblastic and anhedral/granoblastic hematite. High-grade magnetite-hematite ore is formed during this stage. Ore stage 3 hydrothermal specular hematite (spcH)-Fe-dolomite-quartz alteration was controlled by a late-orogenic, brittle, compressional/transpressional stage (D4; the regional-scale shear-zone-related D3 is not preserved in Windarling). This minor event remobilised iron oxides

The enhancing of Au-Ag-Te content in tellurium-bearing ore mineral by bio-oxidation-leaching

Science.gov (United States)

Kim, PyeongMan; Kim, HyunSoo; Myung, EunJi; Kim, YoonJung; Lee, YongBum; Park*, CheonYoung

2015-04-01

The purpose of this study is to enhance the content of valuable metals such as Au-Ag-Te in tellurium-bearing minerals by bio-oxidation-leaching. It was confirmed that pyrite, chalcopyrite, sphalerite and galena were produced together with tellurium-bearing minerals including hessite, sylvanite and tellurobismuthite from ore minerals and concentrates through microscopic observation and SEM/EDS analysis. In a bio-oxidation-leaching experiment, with regard to Au, Ag, Te, Cu and Fe, the changes in the amount of leaching and the content of leaching residues were compared and analyzed with each other depending on the adaptation of an indigenous microbe identified as Acidithiobacillus ferrooxidans. As a result of the experiment, the Au-Ag-Te content in tellurium-bearing ore mineral was enhanced in the order of physical oxidation leaching, physical/non-adaptive bio-oxidation-leaching and physical/adaptive biological leaching. It suggests that the bio-oxidation-leaching using microbes adapted in tellurium-bearing ore mineral can be used as a pre-treatment and a main process in a recovery process of valuable metals. "This research was supported by Basic Science Research Program through the National Research Foundation of Korea(NRF) funded by the Ministry of Education(NRF-2013R1A1A2004898)"

Floatability study of graphite ore from southeast Sulawesi (Indonesia)

Science.gov (United States)

Florena, Fenfen Fenda; Syarifuddin, Fahmi; Hanam, Eko Sulistio; Trisko, Nici; Kustiyanto, Eko; Enilisiana, Rianto, Anton; Arinton, Ghenadi

2016-02-01

Graphite ore obtained from Kolaka Regency, South East Sulawesi, Indonesia have been succesfully investigated for beneficiation by froth flotation technique. Preliminary study have been done to determine the minerals types, fixed carbon content and liberation size of the graphite. Graphite is naturally floatable due to its hydrophobic property. Some suitable reagents are usually added to increase effectiveness of recovery. In this article, enrichment of graphite by froth flotation was studied by investigating the effect of reagents concentrations, rotation speed and particle size on the carbon grade and recovery of the concentrate. The carbon grade increased from 3.00% to 60.00% at the optimum flotation conditions.

Gangue minerals reactivity in oxidative leaching of uraninite with dilute sulfuric acid from low-grade ores. An approach for better leach liquor purity

International Nuclear Information System (INIS)

Madakkaruppan, V.; Chanchal Sarbajna; Pius, Anitha; Sreenivas, T.

2016-01-01

This paper presents results of sulfuric acid leaching studies carried out on a low-grade uranium ore with emphasis on attaining maximum uranium leachability with minimum content of detrimental ions like Si, Al, Fe, Mg and P, which originate from reactive gangue minerals like chlorite, biotite and apatite. A 'two-stage leaching' scheme was developed wherein the total reaction time and the pH of the slurry were split such that the initial phase consists of higher acidity with shorter reaction period and the later phase involves reduced acidity and longer reaction time. This modification gives leach liquor of higher purity with good uranium leachability at relatively lower acid consumption. (author)

The application of CPLD in online nuclear detection meter of ore grade

International Nuclear Information System (INIS)

Yin Yiqiang; Yin Deyou; Gong Yalin; Shang Qingmin; Xiao Xiandong; Zhou Hongjun; Yu Haiming

2010-01-01

The pulse height analysis circuit for nuclear pulse signals is an important function cell of online nuclear detection meter, requiring high speed and credible logic circuit to eliminate the signal pileup rejection, overload detection, instrumentation measurement dead time on the adverse effects of spectrum. In order to improve the performance of nuclear detection meter, some function circuits are used, such as live time offset, overload detection and pileup rejection. The CPLD and multi single-channel spectrum measurement method used in ore grade nuclear instrumentation, eliminating the pileup, overload signal and accurately compensated the measurement of dead time, thus the circuit functions above are carried out credibly and the meter detection accuracy is improved drastically. (authors)

Intensification of the Reverse Cationic Flotation of Hematite Ores with Optimization of Process and Hydrodynamic Parameters of Flotation Cell

Science.gov (United States)

Poperechnikova, O. Yu; Filippov, L. O.; Shumskaya, E. N.; Filippova, I. V.

2017-07-01

The demand of high grade iron ore concentrates is a major issue due to the depletion of rich iron-bearing ores and high competitiveness in the iron ore market. Iron ore production is forced out to upgrade flowsheets to decrease the silica content in the pelettes. Different types of ore have different mineral composition and texture-structural features which require different mineral processing methods and technologies. The paper presents a comparative study of the cationic and anionic flotation routes to process a fine-grain oxidized iron ore. The modified carboxymethyl cellulose was found as the most efficient depressant in reverse cationic flotation. The results of flotation optimization of hematite ores using matrix of second-order center rotatable uniform design allowed to define the collector concentration, impeller rotation speed and air flowrate as the main flotation parameters impacting on the iron ore concentrate quality and iron recovery in a laboratory flotation machine. These parameters have been selected as independent during the experiments.

Automatic checking of heavy element content in polymetallic ores directly in transportation containers

International Nuclear Information System (INIS)

Varvaritsa, V.P.; Mamikon'yan, S.V.; Nagornyj, V.Ya.

1981-01-01

An automatic measuring instrument has been developed and used to check rapidly the content of lead in ores transported by trolley cars, dump trucks, dump cars or other open containers. The measuring technique is based on gamma backscattering and X-ray fluorescence. Influences of container movements, volumetric density changes and matrix effects on the achievable accuracy are briefly discussed

Study on the pre-treatment of oxidized zinc ore prior to flotation

Science.gov (United States)

He, Dong-sheng; Chen, Yun; Xiang, Ping; Yu, Zheng-jun; Potgieter, J. H.

2018-02-01

The pre-treatment of zinc oxide bearing ores with high slime content is important to ensure that resources are utilized optimally. This paper reports an improved process using hydrocyclone de-sliming, dispersion reagents, and magnetic removal of iron minerals for the pre-treatment of zinc oxide ore with a high slime and iron content, and the benefits compared to traditional technologies are shown. In addition, this paper investigates the damage related to fine slime and iron during zinc oxide flotation, the necessity of using hydrocyclone de-sliming together with dispersion reagents to alleviate the influence of slime, and interactions among hydrocyclone de-sliming, reagent dispersion, and magnetic iron removal. Results show that under optimized operating conditions the entire beneficiation technology results in a flotation concentrate with a Zn grade of 34.66% and a recovery of 73.41%.

Considerations on the utilisation of the extraction residue from U, Th production from low grade ores

International Nuclear Information System (INIS)

Huwyler, S.

1979-11-01

A literature review about processes for the winning of metals from the extraction residue of low grade U, Th-ores has been made. Among the metals recoverable aluminium is being considered as the most interesting one. The aluminium extraction processes discussed here include high temperature chlorination, the BAYER-process, acid and SO 3 digestion processes, winning of an AlSiFe-alloy by electrometallurgy. The merits of the different processes are compared. (Auth.)

Microwave enhanced recovery of nickel-copper ore: communition and floatability aspects.

Science.gov (United States)

Henda, R; Hermas, A; Gedye, R; Islam, M R

2005-01-01

A study describing the effect of microwave radiation, at a frequency of 2450 MHz, on the processes of communication and flotation of a complex sulphide nickel-copper ore is presented. Ore communication has been investigated under standard radiation-free conditions and after ore treatment in a radiated environment as a function of ore size, exposure time to radiation, and microwave power. The findings show that communication is tremendously improved by microwave radiation with values of the relative work index as low as 23% at a microwave power of 1.406 kW and after 10 s of exposure time. Communication is affected by exposure time and microwave power in a nontrivial manner. In terms of ore floatability, the experimental tests have been carried out on a sample of 75 microm in size under different exposure times. The results show that both ore concentrate recoveries and grades of nickel and copper are significantly enhanced after microwave treatment of the ore with relative increases in recovered concentrate, grade of nickel, and grade of copper of 26 wt%, 15 wt%, and 27%, respectively, at a microwave power of 1330 kW and after 30 s of exposure time.

Method of continuous pressure leaching of ores

International Nuclear Information System (INIS)

Fiala, P.; Baloun, S.; Polansky, M.

1987-01-01

Ore leaching, especially suspensions of ground ore or fine ore fractions from physical treatment was divided into two operations. The former, i.e., ore mixing with technical grade concentrated sulfuric acid proceeded in a separate mixer. The mixture was then transported into an autoclave where the actual leaching proceeded for 2 to 4 hours. The extracted mixture was discharged through the autoclave bottom. The leaching autoclave used can be without any inner structures. The separation of mixing from the actual leaching allows processing ores with high levels of clay components, increasing operating reliability of the facility, reducing consumption of special structural materials and energy, and increasing process efficiency. (E.S.)

Methods of evaluating ore processing and effluent treatment for Cigar Lake ore at the Rabbit Lake Mill

International Nuclear Information System (INIS)

Edwards, C.R.

2002-01-01

Cigar Lake is the second-largest, high grade uranium orebody in the world. Mineable reserves for Cigar Lake Phase 1 are estimated at 191 million pounds U 3 O 8 with a grade of 25.6% U 3 O 8 . Subject to regulatory approval, Cameco intends to process the majority of ore from Cigar Lake in the Rabbit Lake mill. Cameco initiated a programme to study the processing of Cigar Lake ore and the treatment of the resulting waste streams. Laboratory and follow-up pilot scale ore leaching tests with Cigar Lake ore samples were performed. Tailings and effluents were generated from the products of the pilot scale leach tests. Mill process tailings were blended with ground waste rock. Using these materials, geotechnical and geochemical properties, including long term tailings pore water characteristics, will be evaluated. In addition, proposed changes to the mill waste treatment operations were developed to deal with increased levels of arsenic and radium in the waste streams. This paper describes the methods and techniques Cameco used in this programme. (author)

Mineralogical and geochemical characteristics of the Noamundi-Koira basin iron ore deposits (India)

Science.gov (United States)

Mirza, Azimuddin; Alvi, Shabbar Habib; Ilbeyli, Nurdane

2015-04-01

with kaolinite and gibbsite, which make it low grade. Massive iron ores are devoid of any lamination and usually associated with BHJ and lower shale. The thickness of the massive ore layer varies with the location. The massive iron ore grades in to well-developed bedded BHJ in depth. Blue dust occurs in association with BHJ as pockets and layers. Although blue dust and friable ore are both powdery ores, and subjected to variable degree of deformation, leading to the formation of folding, faulting and joints of complex nature produce favourable channels. Percolating water play an important role in the formation of blue dust and the subterranean solution offers the necessary acidic environment for leaching of quartz from the BHJ. The dissolution of silica and other alkalis are responsible for the formation of blue dust. The friable and powdery ore on the other hand are formed by soft laminated ore. As it is formed from the soft laminated ore, its alumina content remains high similar to soft laminated ore compaired to blue dust. Mineralogy study suggests that magnetite was the principal iron oxide mineral, now a relict phase whose depositional history is preserved in BHJ, where it remains in the form of martite. The platy hematite is mainly the product of martite. The different types of iron ores are intricately related with the BHJ. Hard laminated ores, martite-goethite ore and soft laminated ore are resultant of desilicification process through the action of hydrothermal fluids. Geochemistry of banded iron-formations of the Noamundi-Koira iron ore deposits shows that they are detritus-free chemical precipitates. The mineralogical and geochemical data suggest that the hard laminated, massive, soft laminated ores and blue dust had a genetic lineage from BIF's aided with certain input from hydrothermal activity. The comparative study of major elemental composition of the basin samples and while plotting a binary diagram, it shows a relation between major oxides against

Sedimentary exhalative nickel-molybdenum ores in south China

Science.gov (United States)

Lott, D.A.; Coveney, R.M.; Murowchick, J.B.; Grauch, R.I.

1999-01-01

Unique bedded Ni-Mo ores hosted by black shales were discovered in localized paleobasins along the Yangzte platform of southern China in 1971. Textural evidence and radiometric dates imply ore formation during sedimentation of black shales that grade into readily combustible beds, termed stone coals, which contain 10 to 15 percent organic carbon. Studies of 427 fluid inclusions indicate extreme variation in hydrothermal brine salinities that were contained by Proterozoic dolostones underlying the ore zone in Hunan and Guizhou. Variations of fluid inclusion salinities, which range from 0.1 to 21.6 wt percent NaCl equiv, are attributed to differences in the compositions of brines in strata underlying the ore bed, complicated by the presence of seawater and dilute fluids that represent condensates of vapors generated by boiling of mineralizing fluids or Cambrian meteoric water. The complex processes of ore deposition led to scattered homogenization temperatures ranging from 100??to 187??C within the Hunan ore zone and from 65??to 183??C within the Guizhou ore zone. While living organisms probably did not directly accumulate metals in situ in sufficient amounts to explain the unusually high grades of the deposits, sulfur isotope ratios indicate that bacteria, now preserved as abundant microfossils, provided sufficient sulfide for the ores by reduction of seawater sulfate. Such microbiota may have depended on vent fluids and transported organic matter for key nutrients and are consistent with a sedex origin for the ores. Vent fluids interacted with organic remains, including rounded fragments of microbial mats that were likely transported to the site of ore deposition by the action of waves and bottom currents prior to replacement by ore minerals.

Iron-ore resources of the United States including Alaska and Puerto Rico, 1955

Science.gov (United States)

Carr, Martha S.; Dutton, Carl E.

1959-01-01

The importance of iron ore, the basic raw material of steel, as a fundamental mineral, resource is shown by the fact that about 100 million long tons of steel is used annually in the economy of the United States, as compared with a combined total of about 5 million long tons of copper, lead, zinc, and aluminum. Satisfying this annual demand for steel requires about 110 million tons of iron ore and 70 million tons of scrap iron and steel. The average annual consumption of iron ore in the United States from 1951 to 1955, inclusive, was about 110 million long tons, which is about twice the annual average from 1900 to 1930. Production of iron ore in the United States in this 5-year period averaged approximately 100 million long tons annually, divided by regions as follows (in percent): Lake Superior, 84.1; southeastern, 6.7; western, 6.7; northeastern, 1.4; and central and gulf, 1.1. Mining of iron ore began in the American Colonies about 1619, and for 225 years it was limited to eastern United States where fuel and markets were readily available. Production of iron ore from the Lake Superior region began in 1846; the region became the leading domestic source by 1890, and the Mesabi range in Minnesota has been the world's most productive area since 1896. Proximity of raw materials, water transportation, and markets has resulted in centralization of the country's iron and steel industry in the lower Great Lakes area. Increased imports of iron ore being delivered to eastern United States as well as demands for steel in nearby markets have given impetus to expansion in the steel-making capacity in this area. The four chief iron-ore minerals - hematite, liminite, magnetite, and siderite - are widely distributed but only locally form deposits of sufficient tonnage and grade to be commercially valuable at the present time. The iron content of these minerals, of which hematite is the most important, ranges from 48 percent in siderite to 72 percent in magnetite, but as these

Work within the coordinated programme on bacterial leaching of uranium ores

International Nuclear Information System (INIS)

Jayaram, K.M.V.

1978-10-01

The paper relates geological and lithological aspects of host rocks to the leaching and precipitation of uranium through the agency of microorganisms. For this purpose three different host rocks were studied: a low grade uranium ore analysing 0.045% U 3 O 8 and two high grade ores analysing 0.27% and 1.8% U 3 O 8 respectively. The affect of ore composition, water composition and climatic conditions were studied in relation to the nature of the microflora indigenously developed

Mining and processing of uranium ores in the USSR

International Nuclear Information System (INIS)

Laskorin, B.N.; Mamilov, V.A.; Korejsho, Yu.A.

1983-01-01

Experience gained in uranium ore mining by modern methods in combination with underground and heap leaching is summarized. More intensive processing of low-grade ores has been achieved through the use of autoclave leaching, sorptive treatment of thick pulps, extractive separation of pure uranium compounds, automated continuous sorption devices of high efficiency for processing the underground- and heap-leaching liquors, natural and mine water, and recovery of molybdenum, vanadium, scandium, rare earths and phosphate fertilizers from low-grade ores. Production of ion-exchangers and extractants has been developed and processes for concomitant recovery of copper, gold, ionium, tungsten, caesium, zirconium, tantalum, nickel and cobalt have been designed. (author)

Acid curing and baking of bastnasite ore and concentrate

International Nuclear Information System (INIS)

Topkaya, Y.; Akkurt, S.

1998-01-01

Full text: In this study, the hydrometallurgical evaluation of a rare earth ore as well as a concentrate obtained from this was done at laboratory. For the mentioned study, a bastnasite type rare earth ore located in Beylikahir in Turkey was used. The total rare earth oxide (REO) content of the deposit was estimated to be 1 million tons with an average concentration of 3.42%REO. The rare earths were contained in bastnasite mineral. The other constituents of the ore were calcium fluoride (52.5%), barite (25.4%), calcite (2.8%) and minor amounts of thorium, iron, manganese, etc. The bastnasite mineral occurred either as cement material between fluoride and barite particles or as intimately associated with these minerals. The rare earth elements were enriched considerably in sub-sieve sizes. After extensive research about the physical concentration of this ore, two different metallurgical routes were followed for the extraction of REE from the ore itself or the preconcentrate obtained by attrition scrubbing and desliming by cyclones. In order to increase the grade of the concentrate, upgrading of the preconcentrate by multigravity was also tried. The two metallurgical routes tested were: Sulphuric acid curing and water leaching; Sulphuric acid baking and subsequent water leaching. The results of the leaching experiments were found to be quite promising. Leach recoveries up to 90% were easily obtainable. In the case of acid baking, hydrofluoric acid recover as a by-product was also possible

Manganese Ores from South Sulawesi: Their Potential Uses as Raw Materials for Metallurgical Industry

Directory of Open Access Journals (Sweden)

Sufriadin Sufriadin

2017-03-01

Full Text Available Characterization of manganese ores from Barru and Bone regencies of South Sulawesi has been conducted with the aim at clarification of their mineralogical and chemical composition for their potential uses as the raw materials for metallurgical industry. Mineralogical properties of the ores analyzed by means of optical microscopy and X-ray diffractometry (XRD show that samples from Barru consist mainly of rhodochrosite (MnCO3 with less cryptomelane, groutite, bixbyite, and todorokite. Goethite, calcite and small amount of quartz present as impurities. Manganese ore samples from Bone are predominantly composed of pyrolusite (MnO2 with subordinate ramsdellite and hollandite. Barite, quartz, hematite and clay are present as gangue minerals. Chemical compositions determined by using XRF method revealed that Barru samples contain higher in MnO (average is 40.07 wt% than the Bone samples (average is 34.36 wt%. Similarly, Fe2O3 and CaO are also higher in Barru than those of the Bone samples. In contrast, concentrations of SiO2 and total alkali (K2O + Na2O are lower in the Barru samples. The average P2O5 content of samples in both areas is low (<0.2 wt%. Relatively higher grade of Fe2O3 in the Barru ore implies that it has potential application for ferromanganese production; whereas the elevated SiO2 content of the Bone ore is a good indication for silicomanganese manufacture. However, both ores may not favorable to be directly used as raw materials in metallurgical uses. Prior to be used, the ores should be treated by applying physical beneficiation in order to reduce deleterious elements.

Optimization of staged bioleaching of low-grade chalcopyrite ore in the presence and absence of chloride in the irrigating lixiviant: ANFIS simulation.

Science.gov (United States)

Vakylabad, Ali Behrad; Schaffie, Mahin; Naseri, Ali; Ranjbar, Mohammad; Manafi, Zahra

2016-07-01

In this investigation, copper was bioleached from a low-grade chalcopyrite ore using a chloride-containing lixiviant. In this regard, firstly, the composition of the bacterial culture media was designed to control the cost in commercial application. The bacterial culture used in this process was acclimated to the presence of chloride in the lixiviant. Practically speaking, the modified culture helped the bio-heap-leaching system operate in the chloridic media. Compared to the copper recovery from the low-grade chalcopyrite by bioleaching in the absence of chloride, bioleaching in the presence of chloride resulted in improved copper recovery. The composition of the lixiviant used in this study was a modification with respect to the basal salts in 9 K medium to optimize the leaching process. When leaching the ore in columns, 76.81 % Cu (based on solid residues of bioleaching operation) was recovered by staged leaching with lixiviant containing 34.22 mM NaCl. The quantitative findings were supported by SEM/EDS observations, X-ray elemental mapping, and mineralogical analysis of the ore before and after leaching. Finally, Adaptive neuro-fuzzy inference system (ANFIS) was used to simulate the operational parameters affecting the bioleaching operation in chloride-sulfate system.

PHASE ANALYSES OF URANIUM BEARING MINERALS FROM THE HIGH GRADE ORE, NOPAL I, PENA BLANCA, MEXICO

International Nuclear Information System (INIS)

Ren, M.; Goodell, P.; Kelts, A.; Anthony, E.Y.; Fayek, M.; Fan, C.; Beshears, C.

2005-01-01

The Nopal I uranium deposit is located in the Pena Blanca district, approximately 40 miles north of Chihuahua City, Mexico. The deposit was formed by hydrothermal processes within the fracture zone of welded silicic volcanic tuff. The ages of volcanic formations are between 35 to 44 m.y. and there was secondary silicification of most of the formations. After the formation of at least part of the uranium deposit, the ore body was uplifted above the water table and is presently exposed at the surface. Detailed petrographic characterization, electron microprobe backscatter electron (BSE) imagery, and selected x-ray maps for the samples from Nopal I high-grade ore document different uranium phases in the ore. There are at least two stages of uranium precipitation. A small amount of uraninite is encapsulated in silica. Hexavalent uranium may also have been a primary precipitant. The uranium phases were precipitated along cleavages of feldspars, and along fractures in the tuff. Energy dispersive spectrometer data and x-ray maps suggest that the major uranium phases are uranophane and weeksite. Substitutions of Ca and K occur in both phases, implying that conditions were variable during the mineralization/alteration process, and that compositions of the original minerals have a major influence on later stage alteration. Continued study is needed to fully characterize uranium behavior in these semi-arid to arid conditions

PHASE ANALYSES OF URANIUM-BEARING MINERALS FROM THE HIGH GRADE ORE, NOPAL I, PENA BLANCA, MEXICO

Energy Technology Data Exchange (ETDEWEB)

M. Ren; P. Goodell; A. Kelts; E.Y. Anthony; M. Fayek; C. Fan; C. Beshears

2005-07-11

The Nopal I uranium deposit is located in the Pena Blanca district, approximately 40 miles north of Chihuahua City, Mexico. The deposit was formed by hydrothermal processes within the fracture zone of welded silicic volcanic tuff. The ages of volcanic formations are between 35 to 44 m.y. and there was secondary silicification of most of the formations. After the formation of at least part of the uranium deposit, the ore body was uplifted above the water table and is presently exposed at the surface. Detailed petrographic characterization, electron microprobe backscatter electron (BSE) imagery, and selected x-ray maps for the samples from Nopal I high-grade ore document different uranium phases in the ore. There are at least two stages of uranium precipitation. A small amount of uraninite is encapsulated in silica. Hexavalent uranium may also have been a primary precipitant. The uranium phases were precipitated along cleavages of feldspars, and along fractures in the tuff. Energy dispersive spectrometer data and x-ray maps suggest that the major uranium phases are uranophane and weeksite. Substitutions of Ca and K occur in both phases, implying that conditions were variable during the mineralization/alteration process, and that compositions of the original minerals have a major influence on later stage alteration. Continued study is needed to fully characterize uranium behavior in these semi-arid to arid conditions.

Characterization of Sumbawa manganese ore and recovery of manganese sulfate as leaching products

Science.gov (United States)

Kusumaningrum, Retno; Rahmani, Siti Astari; Widayatno, Wahyu Bambang; Wismogroho, Agus Sukarto; Nugroho, Dwi Wahyu; Maulana, Syahrizal; Rochman, Nurul Taufiqu; Amal, M. Ikhlasul

2018-05-01

The aims of this research were to study the leaching process of manganese ore which originated from Sumbawa, Indonesia and its characterization. A high grade Indonesian manganese ore from Sumbawa, West of Nusa Tenggara was characterized by X-Ray Fluorescence (XRF). The result showed composition of 78.8 % Mn, 17.77% Fe and the rest were trace elements such as Si, Co, Ti, Zn, V and Zr contents. X-Ray Diffraction analysis showed that the manganese ore was consisted of pyrolusite (MnO2), rhodonite (MnSiO3), rhodochrosite (MnCO3) and hematite (Fe2O3). Manganese ore was also analyzed by thermal analysis to observe their thermal decomposition character. In this study, sulphuric acid (H2SO4, 6 M) was deployed as leaching agent. The leaching process was performed at 90 °C for two hours with the addition of NH4OH to control pH. Recovery percentage of leaching process yielded of 87 % Mn extracted. The crystallization process result at heating temperature of 200 °C was confirmed by XRD as manganese sulfate.

Sampling of ore

International Nuclear Information System (INIS)

Boehme, R.C.; Nicholas, B.L.

1987-01-01

This invention relates to a method of an apparatus for ore sampling. The method includes the steps of periodically removing a sample of the output material of a sorting machine, weighing each sample so that each is of the same weight, measuring a characteristic such as the radioactivity, magnetivity or the like of each sample, subjecting at least an equal portion of each sample to chemical analysis to determine the mineral content of the sample and comparing the characteristic measurement with desired mineral content of the chemically analysed portion of the sample to determine the characteristic/mineral ratio of the sample. The apparatus includes an ore sample collector, a deflector for deflecting a sample of ore particles from the output of an ore sorter into the collector and means for moving the deflector from a first position in which it is clear of the particle path from the sorter to a second position in which it is in the particle path at predetermined time intervals and for predetermined time periods to deflect the sample particles into the collector. The apparatus conveniently includes an ore crusher for comminuting the sample particle, a sample hopper means for weighing the hopper, a detector in the hopper for measuring a characteristic such as radioactivity, magnetivity or the like of particles in the hopper, a discharge outlet from the hopper and means for feeding the particles from the collector to the crusher and then to the hopper

Coal-oil gold agglomeration assisted flotation to recover gold from refractory ore

Science.gov (United States)

Otsuki, A.; Yue, C.

2017-07-01

This study aimed to investigate the applicability of coal-oil gold agglomeration (CGA) assisted flotation to recover gold from a refractory ore. The ore with the grade of 2-5 g/t was tested with the CGA-flotation process in six different size fractions from 38 to 300 urn using different collector types and dosages. In addition, the flotation without CGA was performed under the same condition for comparison. The results showed that the higher gold grade and recovery were achieved by applying the CGA-flotation, compared with the flotation without CGA. More than 20-60 times grade increase from the head grade was obtained with CGA-flotation. The elemental analysis of gold and sulphur explained their relationship with gold recovery. The results well indicated the applicability of CGA to upgrade the refractory gold ore.

Bacterial leaching of pyritic gold ores

International Nuclear Information System (INIS)

Gagliardi, F.M.; Cashion, J.D.; Brown, J.; Jay, W.H.

1998-01-01

Full text: Pyritic ores (pyrite and arsenopyrite) containing gold concentrations in excess of 50g Au/t can be processed to recover the gold by the removal of the sulphur from the ore. This may be achieved by roasting (producing sulphur dioxide emissions), pressure oxidation (expensive and suitable for large high grade deposits), pressure leaching (still currently being developed) or bacterial oxidation. The bacterial oxidation process is a well known process in nature but has only recently come under investigation as a economically viable and relatively clean method of gold recovery from deep low grade sulphidic ores. Samples were obtained from the Wiluna Gold Mine in Western Australia consisting of the original ore, six successive bacterial reactors and the final products. Moessbauer experiments have been performed at room temperature, liquid nitrogen and liquid helium temperatures, and in applied magnetic fields. The main components of the iron phases which were present during the bacterial treatment were pyrite and arsenopyrite which were readily oxidised by the bacteria. Ferric sulfates and ferric arsenates were identified as by-products of the process with a small amount of the oxyhydroxide goethite. These results are in contrast to the similar study of the Fairview Mine in South Africa where principally Fe(II) species were observed

Extraction of lithium Carbonate from Petalite Ore (Momeik District, Myanmar)

International Nuclear Information System (INIS)

Tun Tun Moe

2011-12-01

The methods for preparing high purity lithium carbonate which can be used for pharmaceutical applications, electronic grade crystals of lithium or to prepare battery-grade lithium metal are disclosed. Lithium carbonate as commercially produced from mineral extraction, lithium containing brines or sea water. One method for the production of pure lithium carbonate from mineral source (petalite ore) obtained from Momeik District, Myanmar is disclosed. Method for mineral processing of ore concentrate is also disclosed.

Natural resources sustainability: iron ore mining

International Nuclear Information System (INIS)

De La Torre de Palacios, Luis

2011-01-01

In the present article, a new tool to determine environmental sustainability, the energy impact index (EII) was developed to classify different iron mine projects according to two main parameters including energy consumption and CO 2 emissions. The EII considers the characteristics of the mineral (such as the quality, size, hardness, iron ore grade, reducibility, mineral/waste rate, and type of deposit), mining processes (type of exploitation, ore processing, available technology), and transportation (distance to cover).

The fines recovery of the phosphoro-uraniferous ores from Itataia-CE

International Nuclear Information System (INIS)

Furtado, J.R.V.

1985-01-01

Cyclone desliming previous to flotation is one of the determining factors of the concentration performance of phosfate ores. The physical beneficiation of the phosphoro uraniferous ore of Itataia, carried out in the pilot plant, rejects approximately 10,5% P 2 O 5 and 14% U 3 O 8 contained as ''slimes''. The present investigation was to develop a process to recover the fines through the tecniques of flotation and Seletive Floculation. The low P 2 O 5 content and extremely small size of the ''slimes'', led to a low efficiency in the operation of either flotation. The introduction of a Second disliming step swhed promising results. It is work mentioning that the ore presents siliceous-carbonatic gangue and that the direct flotation of phosphates rejects only the silicate portion. Direct flotation followed by reverse flotation of carbonates led to phosphate concentrates containing 28% P 2 O 5 with recoveries of 60%. The results obtained indicate that the fines treatment may lead to increase of 4,5% in overall recovery without decreasing the grade of the final concentrate. (C.D.G.) [pt

Bio-mineralization and potential biogeochemical processes in bauxite deposits: genetic and ore quality significance

Science.gov (United States)

Laskou, Magdalini; Economou-Eliopoulos, Maria

2013-08-01

The Parnassos-Ghiona bauxite deposit in Greece of karst type is the 11th largest bauxite producer in the world. The mineralogical, major and trace-element contents and δ18O, δ12C, δ34S isotopic compositions of bauxite ores from this deposit and associated limestone provide valuable evidence for their origin and biogeochemical processes resulting in the beneficiation of low grade bauxite ores. The organic matter as thin coal layers, overlying the bauxite deposits, within limestone itself (negative δ12C isotopic values) and the negative δ34S values in sulfides within bauxite ores point to the existence of the appropriate circumstances for Fe bio-leaching and bio-mineralization. Furthermore, a consortium of microorganisms of varying morphological forms (filament-like and spherical to lenticular at an average size of 2 μm), either as fossils or presently living and producing enzymes, is a powerful factor to catalyze the redox reactions, expedite the rates of metal extraction and provide alternative pathways for metal leaching processes resulting in the beneficiation of bauxite ore.

Economic outlook for radiometric selection of ores

International Nuclear Information System (INIS)

Formery, P.; Ziegler, V.

1958-01-01

The value of an ore can be increased by cutting off it's poor fractions. This selection may be realized at two stages: - part of the ore in situ is unable to cover it's extraction and treatment costs, this defines the 'underground cut-off grade'; - another portion of already extracted ore is unable to cover it's transport and treatment costs; this defines the 'surface cut off grade'. These selections are easily feasible owing to the property of uranium ores of emitting gamma radiations. A diagram makes possible a fast forecast on the effect of this selection upon the weight and metal yields. An attempt is made as well in order to provide the expected effect of the composition of underground cut off and surface cut off. This cut off however, being realized through an appreciation of the radiations, involves an alteration of the weight and metal yields which calls for a correction. A survey of the economic interest of the cut-off is done and an example of valorisation in a given deposit of a section at the limit of operability is proposed. (author) [fr

Study On Beneficiation Technology Of Dong Pao Rare-Earth-Barite-Fluorite With Two Product Plans About Content And Recovery Of Rare-Earth Fine Ores

International Nuclear Information System (INIS)

Duong Van Su; Truong Thi Ai; Bui Ba Duy; Bui Thi Bay; Nguyen Hong Ha; Le Thi Hong Ha; Doan Thi Mo; Doan Dac Ban; Nguyen Hoang Son

2014-01-01

The ore sample used in the research was taken from the F3 ore bodies and the sample of the F7, F9 and F16 ore bodies which contain the average of 5.98% TR 2 O 3 ; they are multi-metals ore which is difficult to enrich, highly weather with very complex ingredients. The process of the experiment is the ore is crushed, ground, screened and classified reasonably to -0.1 mm and divided into 3 particle size with the following technique: (1) -0.020 mm is primary sludge and the rare-earth fine ore; (2) 0.075-1 mm is gotten through the sludge concentrating table with the output is the 2 parts: the heavy part which is dried magnetic separator with high magnetism to get the rare-earth fine ore and the light one; (3) Light minerals, non-magnetic and ferromagnetic minerals group are ground together to 85% of them get size within -0.075 mm then mix it with 0.020-0.075 mm group. Using flotation separator, get barite-rare earth mixture and fluorite. After that, we separate this mixture by secondary flotation and get refined rare earth, barite and fluorite mineral. The result of the theme: (1) product plan A-rare-earth fine ore has TR 2 O 3 content archive 42.07% with recovery is 69.70%; (2) product plan B-rare-earth fine ore has TR 2 O 3 content archive 29.64% with recovery is 80.01%. (author)

Development of the Method of Bacterial Leaching of Metals out of Low-Grade Ores, Rocks, and Industrial Wastes Using Neutron Activation Analysis

CERN Document Server

Tsertsvadze, L A; Petriashvili, Sh G; Chutkerashvili, D G; Kirkesali, E I; Frontasyeva, M V; Pavlov, S S; Gundorina, S F

2001-01-01

The results of preliminary investigations aimed at the development of an economical and easy to apply technique of bacterial leaching of rare and valuable metals out of low-grade ores, complex composition ores, rocks, and industrial wastes in Georgia are discussed. The main groups of microbiological community of the peat suspension used in the experiments of bacterial leaching are investigated and the activity of particular microorganisms in the leaching of probes with different mineral compositions is assessed. The element composition of the primary and processed samples was investigated by the epithermal neutron activation analysis method and the enrichment/subtraction level is estimated for various elements. The efficiency of the developed technique to purify wastes, extract some scrace metals, and enrich ores or rocks in some elements, e.g. Au, U, Th, Cs, Sr, Rb, Sc, Zr, Hf, Ta, Gd, Er, Lu, Ce, etc., is demonstrated.

Functional activity of microorganisms in mining and processing of copper-nickel ores in the Murmansk Region

Directory of Open Access Journals (Sweden)

Fokina N. V.

2018-03-01

Full Text Available The quantitative indices and structure of the microbial community in flotation samples of sulfide copper-nickel ores at concentration plant of Kola Mining and Metallurgical Company have been determined. The smallest number of saprotrophic and oligotrophic bacteria has been observed in samples of ore and recycled water, which can be explained by the low temperature of samples and the lack of nutrients. It has been found out that the bacteria contained in the ore and recycling water flowing from the tailings increased their number during the flotation process due to coming of the organic compounds with the flotation reagents, aeration and increased temperature. Dominating strains have been isolated from recycled water and basic flotation products and classified as Pseudomonas. It has been shown that with an increase in the number of bacteria, the flotation time of copper-nickel ores increases. There is also a tendency to change the extraction of copper and nickel, which can be caused by both the increase in the flotation time for operations and the change in the number of bacteria in the circulating water. The thionic bacteria have been distinguished from the flow tailings of the Allarechensk deposit. The heap leaching experiments have proved the bacterial leaching to give good results on the ore samples passed through magnetic separation, having shown high content of the nickel and copper in filters. When leaching low-grade ore of the Nude Terrasa, the advantage of bacterial leaching use in comparison with the sulphuric-acid leaching only to copper has been revealed. The nickel content in the filtrates for bacterial leaching is 275 mg/l, and for sulfuric acid – 310 mg/l. The average copper content in the filtrates is 19 and 15 mg/l.

A Review on New Technological Progress for Beneficiation of Refractory Phosphate Ore in China

Science.gov (United States)

Dong, Xu; Siqing, Liu; Yanqing, Yao; Hailin, Liu; Yi, Pei

2017-05-01

The world is rich in phosphate resources, but the vast majority of the resources are of middle and low grade ores, and it is difficult to obtain high grade concentrate at a high recovery by using traditional separation methods. In this paper, the distribution and flotation processes of typical phosphate ores in China are introduced. Considering the current situation in phosphate ore beneficiation both home and abroad, the new trend of processing technology and reagents in China are summarized. Flotation is still regarded as the main processing method in phosphate ore beneficiation for a certain time in near future.

Sintering of manganese ore in natura with different additions on activated carbon

International Nuclear Information System (INIS)

Lima, M.M.F.; Mapa, T.F.M.; Lima, R.M.F.

2016-01-01

Full text: The shortage of high grade manganese ore and the importance of economically viable processes suggest a necessity of the recovery of ore residues. So, this work presents a route to obtain by-products of economic interest from manganese ore residues in bench scale. The objective was the sintering of manganese ore in natura using a particle size below 0,037μm with different additions of activated carbon. For this, the fine residues were calcined at 800°C during 60 minutes, homogenized in an agate mortar with 12% humidity and additions of 9 and 12% of activated carbon. After homogenization, the sintering process was carried out at 1145°C and 1155°C during 5, 15 and 30 minutes at natural air. The products sintered were characterized by bulk density, BET surface area, OM, SEM / EDS and diffraction X-rays. During the calcination of the ore, the mass loss was (15.16 ± 0.02)% due to the elimination of volatiles and water. The surface area of the ore was reduced due to the diffusion process that occurred during sintering. While, the bulk density values had little variation, around (3.51 ± 0.06)g/cm³. The analyses of micro-regions EDS showed that the matrix is a silicate with a high Mn content. It was identified yet, other silicates with different proportions of Si, Al, Ti, Na, Mn, Mg and Ca. (author)

Sintering of manganese ore in natura with different additions on activated carbon

Energy Technology Data Exchange (ETDEWEB)

Lima, M.M.F.; Mapa, T.F.M.; Lima, R.M.F. [Universidade Federal de Ouro Preto (UFOP), MG (Brazil)

2016-07-01

Full text: The shortage of high grade manganese ore and the importance of economically viable processes suggest a necessity of the recovery of ore residues. So, this work presents a route to obtain by-products of economic interest from manganese ore residues in bench scale. The objective was the sintering of manganese ore in natura using a particle size below 0,037μm with different additions of activated carbon. For this, the fine residues were calcined at 800°C during 60 minutes, homogenized in an agate mortar with 12% humidity and additions of 9 and 12% of activated carbon. After homogenization, the sintering process was carried out at 1145°C and 1155°C during 5, 15 and 30 minutes at natural air. The products sintered were characterized by bulk density, BET surface area, OM, SEM / EDS and diffraction X-rays. During the calcination of the ore, the mass loss was (15.16 ± 0.02)% due to the elimination of volatiles and water. The surface area of the ore was reduced due to the diffusion process that occurred during sintering. While, the bulk density values had little variation, around (3.51 ± 0.06)g/cm³. The analyses of micro-regions EDS showed that the matrix is a silicate with a high Mn content. It was identified yet, other silicates with different proportions of Si, Al, Ti, Na, Mn, Mg and Ca. (author)

Zeolitization at uranium ore manifestation

International Nuclear Information System (INIS)

Petrosyan, R.V.; Buntikova, A.F.

1981-01-01

The process of zeolitization at uranium ore manifestation is studied. A specific type of low-temperature wall endogenous alteration of rocks due to the effect of primary acid solution with low content of carbonic acid is established. Leaching of calcium from enclosing rocks and its deposition in ore-accompanying calcium zeolites is a characteristic feature of wall-metasomatosis. Formation of desmin- calcite-laumontite and quartz-fluoroapatite of vein associations, including ore minerals (uranophane and metaotenite), is genetically connected with calcium metasomatosis. On the basis of the connection of ore minerals with endogeneous process of zeolitization a conclusion can be made on endogenous origin of uranophane and metaotenite [ru

High-rate behaviour of iron ore pellet

Science.gov (United States)

Gustafsson, Gustaf; Häggblad, Hans-Åke; Jonsén, Pär; Nishida, Masahiro

2015-09-01

Iron ore pellets are sintered, centimetre-sized spheres of ore with high iron content. Together with carbonized coal, iron ore pellets are used in the production of steel. In the transportation from the pelletizing plants to the customers, the iron ore pellets are exposed to different loading situations, resulting in degradation of strength and in some cases fragmentation. For future reliable numerical simulations of the handling and transportation of iron ore pellets, knowledge about their mechanical properties is needed. This paper describes the experimental work to investigate the dynamic mechanical properties of blast furnace iron ore pellets. To study the dynamic fracture of iron ore pellets a number of split Hopkinson pressure bar tests are carried out and analysed.

Preparatory studies for the on-line determination of zinc content in zinc ore slurries by radioisotope excited X-ray fluorescence

International Nuclear Information System (INIS)

Donhoffer, D.K.

1977-01-01

Laboratory tests were carried out to prove the feasibility of determination of Zn-content in zinc ore slurries by isotope excited x-ray fluorescence. Matrix effects were investigated on dry samples. A slurry testloop was built and measurements on slurries were made. The results indicated that the measurement on Zn in ore slurries can be made with a precision of 0,05% Zn. A working equation for interpretation of the measurements is derived. (author)

Influence of microwaves on the leaching kinetics of uraninite from a low grade ore in dilute sulfuric acid

International Nuclear Information System (INIS)

Madakkaruppan, V.; Pius, Anitha; Sreenivas, T.; Giri, Nitai; Sarbajna, Chanchal

2016-01-01

Highlights: • U leaching from a low-grade Si-rich ore studied in H_2SO_4 medium with (MW) irradiation. • MW heating is more efficient in terms of U recovery, kinetics and purity of liquor. • U leachability of 84% obtained in 90 min at 95 °C with 0.38 M H_2SO_4 at 450 mVwith MW heating • Conventional conductive heating gave about 74% leachability with less purity liquor. • U leaching was found follow product layer diffusion as controlling mechanism. - Abstract: This paper describes a study on microwave assisted leaching of uranium from a low-grade ore of Indian origin. The host rock for uranium mineralization is chlorite-biotite-muscovite-quartzo-feldspathic schist. The dominant presence of siliceous minerals determined leaching of uranium values in sulfuric acid medium under oxidizing conditions. Process parametric studies like the effect of sulfuric acid concentration (0.12–0.50 M), redox potential (400–500 mV), particle size (600–300 μm) and temperature (35°–95 °C) indicated that microwave assisted leaching is more efficient in terms of overall uranium dissolution, kinetics and provide relatively less impurities (Si, Al, Mg and Fe) in the leach liquor compared to conventional conductive leaching. The kinetics of leaching followed shrinking core model with product layer diffusion as controlling mechanism.

Influence of microwaves on the leaching kinetics of uraninite from a low grade ore in dilute sulfuric acid

Energy Technology Data Exchange (ETDEWEB)

Madakkaruppan, V. [Atomic Minerals Directorate for Exploration and Research, Begumpet, Hyderabad 500016 (India); Pius, Anitha, E-mail: dranithapius@gmail.com [Department of Chemistry, Gandhigram Rural Institute, Gandhigram, Dindigul District, Tamil Nadu 624302 (India); Sreenivas, T.; Giri, Nitai [Mineral Processing Division, Bhabha Atomic Research Center, AMD Complex, Begumpet, Hyderabad 500016 (India); Sarbajna, Chanchal [Atomic Minerals Directorate for Exploration and Research, Begumpet, Hyderabad 500016 (India)

2016-08-05

Highlights: • U leaching from a low-grade Si-rich ore studied in H{sub 2}SO{sub 4} medium with (MW) irradiation. • MW heating is more efficient in terms of U recovery, kinetics and purity of liquor. • U leachability of 84% obtained in 90 min at 95 °C with 0.38 M H{sub 2}SO{sub 4} at 450 mVwith MW heating • Conventional conductive heating gave about 74% leachability with less purity liquor. • U leaching was found follow product layer diffusion as controlling mechanism. - Abstract: This paper describes a study on microwave assisted leaching of uranium from a low-grade ore of Indian origin. The host rock for uranium mineralization is chlorite-biotite-muscovite-quartzo-feldspathic schist. The dominant presence of siliceous minerals determined leaching of uranium values in sulfuric acid medium under oxidizing conditions. Process parametric studies like the effect of sulfuric acid concentration (0.12–0.50 M), redox potential (400–500 mV), particle size (600–300 μm) and temperature (35°–95 °C) indicated that microwave assisted leaching is more efficient in terms of overall uranium dissolution, kinetics and provide relatively less impurities (Si, Al, Mg and Fe) in the leach liquor compared to conventional conductive leaching. The kinetics of leaching followed shrinking core model with product layer diffusion as controlling mechanism.

Calculation of U, Ra, Th and K contents in uranium ore by multiple linear regression method

International Nuclear Information System (INIS)

Lin Chao; Chen Yingqiang; Zhang Qingwen; Tan Fuwen; Peng Guanghui

1991-01-01

A multiple linear regression method was used to compute γ spectra of uranium ore samples and to calculate contents of U, Ra, Th, and K. In comparison with the inverse matrix method, its advantage is that no standard samples of pure U, Ra, Th and K are needed for obtaining response coefficients

Ore petrography of a sedimentary uranium deposit, Live Oak County, Texas

International Nuclear Information System (INIS)

Bomber, B.J.; Ledger, E.B.; Tieh, T.T.

1986-01-01

Samples from the McLean 5 open-pit uranium mine, a small high-grade deposit located along a normal fault in the Miocene Oakville sandstone of Live Oak County, Texas, have been studied for uranium abundance, distribution, and nature of occurrence on the microscopic level. The host sandstone is composed of quartz, feldspars, and volcanic rock fragments, cemented by sparry calcite. Authigenic minerals include iron disulfide minerals (dominantly pyrite and some marcasite) and small amounts of clays, Ti oxides, and opal. High-grade ore (to 3% U) occurs along the fault, decreasing to less than 1,000 ppm within 10 m from the fault. The ore mineral is amorphous pitchblende and exhibits botryoidal morphology. The microscopic occurrence of uranium, documented by fission-track mapping of petrographic thin sections, is presented in detail. Uranium occurs abundantly as grain coatings and fillings in intergranular spaces in samples with high uranium content, where calcite cement has been partially or totally leached as mineralization proceeded. Lesser amounts are adsorbed onto leucoxene (microcrystalline anatase), mud clasts, and altered igneous rock fragments. Adsorbed uranium is the major code of occurrence in samples, with lower uranium contents farther from the orebody. Textural relations indicate that iron sulfides formed both before and after mineralization. Initial mineralization was by adsorption onto aggregates of fine particles of Ti oxide and clay minerals of various origins. With dissolution of cement and continued uranium influx, uranium precipitated as grain coatings and pore fillings

Study of the sulfuric acid leaching and bacterial leaching of low grade uranium ore by orbital shaker experiment

International Nuclear Information System (INIS)

Li Guangyue; Liu Yulong; Wang Yongdong; Ding Dexin

2009-01-01

The sulphuric acid leaching and bacteria leaching by orbital shaker experiments were conducted for the low grade uranium ore from a uranium mine in Guangdong Province. The results show that, when the concentration of sulphuric acid and that of slurry were 30 g/L and 25%, respectively, the conditions were most favourable for sulphuric acid leaching and the rate of leaching reached 92.92%, that, when pH value was 1.5, inoculation amount, 10%, concentration of slurry, 10%, the conditions were most favourable for bacteria leaching and the rate of leaching reached 95.93%, that, compared with sulphuric acid leaching, bacteria leaching decreased sulphuric acid consumption by 17.2% and increased the rate of leaching by 3%, and that, under the most favourable conditions for suphuric acid leaching, if 1% natrium chlorate was added, the rate of leaching increased to 96.46%, but 10 kg of natrium chlorate was consumed for 1 ton of uranium ore. (authors)

Effects of High Pressure ORE Grinding on the Efficiency of Flotation Operations

Science.gov (United States)

Saramak, Daniel; Krawczykowska, Aldona; Młynarczykowska, Anna

2014-10-01

This article discusses issues related to the impact of the high pressure comminution process on the efficiency of the copper ore flotation operations. HPGR technology improves the efficiency of mineral resource enrichment through a better liberation of useful components from waste rock as well as more efficient comminution of the material. Research programme included the run of a laboratory flotation process for HPGR crushing products at different levels of operating pressures and moisture content. The test results showed that products of the high-pressure grinding rolls achieved better recoveries in flotation processes and showed a higher grade of useful components in the flotation concentrate, in comparison to the ball mill products. Upgrading curves have also been marked in the following arrangement: the content of useful component in concentrate the floatation recovery. All upgrading curves for HPGR products had a more favourable course in comparison to the curves of conventionally grinded ore. The results also indicate that various values of flotation recoveries have been obtained depending on the machine operating parameters (i.e. the operating pressure), and selected feed properties (moisture).

A laboratory study to evaluate the possibility of sulphur and phosphorous removal from iron ore concentrate by leaching

Directory of Open Access Journals (Sweden)

Pour Hassan Rezvani

2016-01-01

Full Text Available Iron ore concentrates with high grade sulfur cause several problems in the steel making process, and hence affect the concentrate price. Environmental issues such as sulfur dioxide emission during the concentrate pelletizing process and effect on the steel quality are other issues. The current study was focused on removal of sulfur from the iron ore concentrate by using the chemical leaching technique. The magnetite iron ore concentrate was chosen for this purpose. The results obtained showed that more than 90% of the total sulfur content was removed from the iron ore concentrate by chemical leaching. Effects of several parameters such as temperature, particle size and use of organic solvent on sulfur removal were investigated by a series of experiments. After optimizing the experimental conditions, it was demonstrated that with addition of sulfur, phosphorus, another important impurity was also removed from the iron ore concentrate. In addition, one of the major advantages of our proposed method was transformation of mineral pyrites to useful by-products such as elemental sulfur.

Assessment of the contrast of rare metal ores

International Nuclear Information System (INIS)

Kuznetsova, O.V.

1987-01-01

The method of rapid assessment of useful component content on the basis of X-ray radiometric method of analysis of non-crushed ore lumps is presented. Using as an example rare metal deposits, linear dependence between logarithms of Nb 2 O 6 contents and the value of fragment separation index during radiometric separation is established. The use of the dependence ensures sufficient accuracy for the characteristic of rare metal ore content

Recovery of uranium mineral from Liaoning Fengcheng ludwigite ore by gravity concentration

International Nuclear Information System (INIS)

Zhang Tao; Liang Haijun; Xue Xiangxin

2009-01-01

A laboratory research was carried out to recover uranium mineral from Liaoning Fengcheng ludwigite ore. Gravity concentration methods including hydroclone, spiral chute and shaking table were applied in this study. The results show that a concentrate with uranium grade of 0.216% and recovery of 44.24% could be produced from the feed of uranium content 0.006 3%. This research is helpful to comprehensive utilization of the mineral resources. Increasing further uranium mineral liberation degree is the key to improve separation effects. (authors)

Content and Grade Trends in State Assessments and NAEP.

Directory of Open Access Journals (Sweden)

William D. Schafer

2007-08-01

Full Text Available Each state is required by the No Child Left Behind Act to report the percents of its students who have reached a score level called - proficient- or above for certain grades in the content areas of reading (or a similar construct and math. Using 2005 data from public web sites of states and the National Assessment of Educational Progress (NAEP, state-to-state differences in percents were analyzed, both unconditionally and conditionally on NAEP, for (1 trend across content areas (horizontal moderation, (2 trend across grade levels (vertical moderation, and (3 consistency with NAEP. While there was considerable variation from state to state, especially on an idealistic-realistic dimension, the results generally show that states are relatively consistent in trends across grades and contents.

Utilizing a Value of Information Framework to Improve Ore Collection and Classification Procedures

National Research Council Canada - National Science Library

Phillips, Julia A

2006-01-01

.... We use a value of information framework (VOI) to consider the economic feasibility of a mine purchasing additional information on extracted ore type to reduce the uncertainty of extracted ore grade quality...

Status Report from Sweden [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

Peterson, A [AB Atomenergi, Stockholm (Sweden)

1967-06-15

The Ministry of Education was authorized in November 1945 to appoint a commission to study the organization of nuclear energy research. In April 1947 this commission, the Swedish Atomic Energy Commission, proposed the formation of a semi-state-owned company to be a central body for applied research work and development in the nuclear energy field in Sweden. In November 1947 the Atomic Energy Company (AB Atomenergi) had its statutory meeting. The State owns 4/7 of the share capital and the remaining 3/7 is owned by 71 private and municipal share-holders. Except for a part of the stock capital, all investments and running costs of the company have been financed by the Government. The company is in practice answerable to the Department of Commerce which has an advisory body, the Atomic Energy Board. AB Atomenergi is responsible for Government-financed research on the industrial applications of nuclear energy, the milling of uranium ores and refining of uranium. The total number of employees is at present about 1400, 800 of which work at the company's research establishment Studsvik about 120 km south of Stockholm. As early as 1945 the Research Institute of the Swedish National Defence started work in the field of uranium processing. Similar work was also started quite early by the Boliden Mining Company, the Swedish Shale Oil Company and Wargons AB. After the establishment of AB Atomenergi, all work in the uranium processing field was transferred to this company. In fact one of the main reasons for the formation of AB Atomenergi was the need for Swedish uranium production as there was no possibility of importing uranium at that time. As a result of research and development in uranium processing a pilot plant at Kvarntorp near Orebro in central Sweden started milling a low-grade uranium ore (shale) in 1953. The capacity of this plant was 5-10 tons of uranium a year. A uranium mill at Ranstad in south-west Sweden, near Skovde, with a capacity of 120 tons of uranium a

Evaluation of chromite ore and the optimum methods for industrial extraction of chromium

International Nuclear Information System (INIS)

Salih, Bakheit Mustafa Mohamed

1999-10-01

Samples of chromite ore, collected from Gam and Cheikay mining area (Ingaessana Hills) in east Sudan, were analysed to assess the chromium content. Analysis were carried out using atomic absorption spectroscopy (AAS) to estimate the contents of chromium, iron, calcium and magnesium. X-ray florescence (XRF) was used to evaluate the levels of chromium, iron and calcium in the ore. Volumetric analysis was performed to assess chromium and iron, whilest gravimetric analysis was employed to measure the amounts of calcium, magnesium, aluminum and silicon present in the ore. The results are in a good agreement except iron oxide, which displayed a significantly different value when measured by x-ray fluorescence. The data obtained exhibited similarity in almost all cases, when compared with local and global researches, reports and literature. The study has revealed the average contents of Cr 2 O 3 , FeO, CaO, MgO, Al 2 O 3 , and SiO 2 as 40.66, 11.96, 11.94, 0.36, 16.94, 11.45% respectively. MnO and NiO were detected in trace amounts, the corresponding levels in the ore being 72 and 27 ppm. The average chromium content in extracted potassium dichromate measured by using AAS, XRF, and volumetric methods was found to be 31.7%. The highest grade reached by individual technique being 33.10%. The extraction with sodium peroxide is the optimum method for preparation of potassium dichromate. X-ray diffraction analysis, has showed that the d spaces and intensities of prepared potassium dichromate are isostructural with the corresponding ones of standard potassium dichromate. This suggests that the composition of the two samples is identical. Chromite samples were analysed using gamma ray spectroscopy in order to estimate the levels of radioactive elements present. It was found that the concentrations of 232 Th and 40 K range from 7.62 to 10.98 Bq/kg and 47.38 to 56.28 Bq/kg respectively

Aqueous-chlorine leaching of typical Canadian uranium ores

International Nuclear Information System (INIS)

Haque, K.E.

1982-01-01

Laboratory-scale aqueous-chlorine leaches were conducted on quartz-pebble conglomerates, pegmatite and vein-type ores. Optimum leach temperatures, pulp density and retention times were determined. Uranium extraction of 98 per cent was obtained from the Elliot Lake, Madawaska Mines of Bancroft and Rabbit Lake ores, 96 per cent from the Key Lake ore and 86 per cent from the Agnew Lake ore. However, tailings containing 15-20 pCi g -1 of radium-226 were obtained only from the Elliot Lake and Agnew lake quartz-pebble conglomerates and Bancroft pegmatite-type ores by second-stage leaches with HCl. The second-stage leach results indicate that multistage (3 or 4) acid-chloride or salt-chloride leaches might be effective to obtain tailings containing 15-20 pCi 226 Ra g -1 from the high-grade vein-type ores. Comparative reagent-cost estimates show that the sulphuric-acid leach process is far less expensive than aqueous chlorine leaching. Nevertheless, only the aqueous chlorine and acid-chloride leaches in stages are effective in producing tailings containing 15-20 pCi 226 Ra g -1 from the typical Canadian uranium ores. (Auth.)

The allocation of gold production from multiple shafts feeding a common treatment plant using run-of-mine sampling of ore deliveries

OpenAIRE

Bartlett, H.E.; Korff, L.; Minnitt, R.C.A.

2014-01-01

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject ...

Optimizing grade-control drillhole spacing with conditional simulations

Directory of Open Access Journals (Sweden)

Adrian Martínez-Vargas

2017-01-01

Full Text Available This paper summarizes a method to determine the optimum spacing of grade-control drillholes drilled with reverse-circulation. The optimum drillhole spacing was defined as that one whose cost equals the cost of misclassifying ore and waste in selection mining units (SMU. The cost of misclassification of a given drillhole spacing is equal to the cost of processing waste misclassified as ore (Type I error plus the value of the ore misclassified as waste (Type II error. Type I and Type II errors were deduced by comparing true and estimated grades at SMUs, in relation to a cuttoff grade value and assuming free ore selection. True grades at SMUs and grades at drillhole samples were generated with conditional simulations. A set of estimated grades at SMU, one per each drillhole spacing, were generated with ordinary kriging. This method was used to determine the optimum drillhole spacing in a gold deposit. The results showed that the cost of misclassification is sensitive to extreme block values and tend to be overrepresented. Capping SMU’s lost values and implementing diggability constraints was recommended to improve calculations of total misclassification costs.

The performance of leaching and bio-leaching from sulphide ores usiing SEVOP

OpenAIRE

Krstev, Boris; Krstev, Aleksandar; Golomeov, Blagoj; Golomeova, Mirjana; Sala, Ferat; Gocev, Zivko; Zivanovic, Jordan; Krstev, Dejan

2013-01-01

The refractory or low grade copper chalcopyrite ores or galena/sphalerite domestic ores in Republic of Macedonia are investigated by conventional copper flotation and selective flotation for galena/sphalerite. In the meantime, investigations are directed to the new possibilities of leaching by microorganisms – bioleaching. The paper is result of these technologies and investigations carried out for recovery of in the mentioned ores. Using Simplex EVOP and computer programme. Multisimple...

Residues leaching from 'Factory of barren ores'

International Nuclear Information System (INIS)

Rakhmatov, N.; Khakimov, N.; Nazarov, Kh.M.; Barotov, A.M.

2012-01-01

The objective of the present work is safe management of residues from Factory of Barren Ores, their reprocessing, expenditures reduction for remediation of Istiklol city former uranium tailings. For this purpose, some experiences were adopted - Factory of Barren Ores tailing use for filling up the open pit where water with uranium content 3-5 mg/l is located. Factory of Barren Ores waste are passed through heap leaching and have some amount of uranium salts dissolved in water. Thus, we propose to dissolve uranium from Factory of Barren Ores wastes with uranium bearing water flowing out from gallery and filling up the open-pit by radioactive wastes. In so doing, uranium content flowing out from gallery will increase twice, and further, passing them through apricot's shell, as a sorbent, we will clean the water against radionuclides. Residue samples with uranium content 0,015% from Factory of Barren Ores and uranium bearing waters from gallery 1 with uranium content 0,0025 g/l were used for laboratory tests. After which, a slurry was prepared by means of residue mixing with water in ratio of solid and liquid phases (S:L) - 1:2 and 9,7 ml of sulfuric acid (Ρ=1,82) was added which corresponds consumption by H 2 SO 4 176,54 kg/t. For the first test, leaching was carried out during 4 hours at ph=1,6 at room temperature. For the second test, leaching was carried out at 60 d eg C a nd ph=1,6 during 4 hours. Slurry heating and mixing was carried out by means of magnetic mixer. The basic residue leaching indicators are provided in this article.

Uranium reduction by carbon oxide during ore formation

International Nuclear Information System (INIS)

Matyash, I.V.; Gavrusevich, I.B.; Pasal'skaya, L.F.; Shcherba, D.I.

1981-01-01

Using the method of gas chromatography the gas content in Pre-Cambrian granitoils of various types and in natrometasomatites associted with them is studied. It is established that granites associated with ore-bearing albitites have sharply elevated amounts of CO as compared with granites, which do not include mineralization. Simultaneously in ore samples the absence or sharply low amounts of CO as compared with ore-free samples is observed, that is reverse dependence of CO and ore components. Carbon oxide is the reducing agent of uranium mineralization and alongside with other reducing agents can be a geochemical barrier in the process of ore formation [ru

On a Bayesian estimation procedure for determining the average ore grade of a uranium deposit

International Nuclear Information System (INIS)

Heising, C.D.; Zamora-Reyes, J.A.

1996-01-01

A Bayesian procedure is applied to estimate the average ore grade of a specific uranium deposit (the Morrison formation in New Mexico). Experimental data taken from drilling tests for this formation constitute deposit specific information, E 2 . This information is combined, through a single stage application of Bayes' theorem, with the more extensive and well established information on all similar formations in the region, E 1 . It is assumed that the best estimate for the deposit specific case should include the relevant experimental evidence collected from other like formations giving incomplete information on the specific deposit. This follows traditional methods for resource estimation, which presume that previous collective experience obtained from similar formations in the geological region can be used to infer the geologic characteristics of a less well characterized formation. (Author)

Uranium extraction from Uro area phosphate ore, Nuba mountains, Sudan

International Nuclear Information System (INIS)

Mohammed, A. A.; Eltayeb, M. A. H.

2003-01-01

This study was carried out mainly to extract uranium from Uro area phosphate ore in the eastern part of Nuba mountains near Abu Gibiha town in southern Kurdufan state. For this purpose first, the phosphate ore samples were decomposed with sulphuric acid. the resulting phosphoric acid was filtered off, and pretreated with pyrite and activated charcoal. the chemical analysis of the obtained grain phosphoric acid showed that about 98% of uranium content of the phosphate ore was rendered soluble in the phosphoric acid. The clear green phosphoric acid was introduced to uranium extraction by 25% tributylphosphate (Tbp) in kerosene. The effect of several factors on the extraction and stripping processes namely, interference's effect, the suitable strip solution, the required number of extraction and stripping stages, the optimum phase ratio have been studied in details. A three stage extraction at a phase ratio (aqueous/organic) of 1:2, followed by two stages stripping using 0.5 M sodium carbonate solution at a phase ratio (A/O) of 1:4 were found to be the optimum conditions to report more than 98% of uranium content in green phosphoric acid to the aqueous phase as uranyl tricarbonate complex (UO 2 (CO 3 ) 3 ) 4- . By applying sodica decomposition upon the stripping carbonate solution using 50% sodium hydroxide, about 98% of uranium content was precipitated as sodium diuranate concentrate (Na 2 U 2 O 7 ). The chemical analysis using atomic absorption spectrometry (Aas) showed a good agreement between the specification of the obtained uranium concentrate with the standard commercial specification of sodium diuranate concentrate. Further purification was achieved for the yellow cake by selective precipitation of uranium from the solution as uranium peroxide (UO 4 .2H 2 O) using 30% hydrogen peroxide. Finally the uranium peroxide precipitated was calcined at 450 degree C to obtain the orange powder uranium trioxide (UO 3 ). The chemical analysis of the final uranium trioxide

Organization of radiation inspection for strip-mining development for ores with elevated content of natural radionuclides on the Karazhyra coal mine

International Nuclear Information System (INIS)

Lukashenko, S.N.; Subbotin, S.B.; Ajdarkhanov, A.O.; Medvedev, P.P.

2003-01-01

Due to existence of anomalous areas of ores with elevated content of natural radionuclides on the Karazhyra coal mine the project of its selective development was implemented. The project provides a set of measures on radiation safety. In the present paper the order of radiological operations organization and performance are shown, and methodical provision of these works is considered. Results of the preliminary radiological examination of the area, fulfilment the measures on mine works technology radiological safety, and strip-mining ores deposition are analyzed. The evaluations of natural radionuclides content with taking into account its influence on personnel during works fulfilment are made. The results of soil samples analysis are presented in the graphical form. The suggestions and recommendations on radiation monitoring improvement on the area are given

Bottle roll leach test for Temrezli uranium ore

International Nuclear Information System (INIS)

Çetin, K.; Bayrak, M.; Turan, A. İsbir; Üçgül, E.

2014-01-01

The bottle roll leach test is one of the dynamic leaching procedure which can meet in-situ mining needs for determining suitable working conditions and helps to simulate one of the important parameter; injection well design. In this test, the most important parameters are pulp density, acidic or basic concentration of leach solution, time and temperature. In recent years, bottle roll test is used not only for uranium but also gold, silver, copper and nickel metals where in situ leach (ISL) mining is going to be applied. For this purpose for gold and silver metal cyanide bottle roll tests and for uranium metal; acidic and basic bottle roll tests could be applied. The new leach test procedure which is held in General Directorate of Mineral Research and Exploration (MTA) of Turkey is mostly suitable for determining metal extraction conditions and recovery values in uranium containing ore bodies. The tests were conducted with samples taken from Temrezli Uranium Ore located in approximately 200 km east of Turkey’s capital, Ankara. Mining rights of Temrezli Ore is controlled 100% by Anatolia Energy Ltd. The resource estimate includes an indicated mineral resource of 10.827 Mlbs U_3O_8 [~4160 t U] at an average grade of 1426 ppm [~1210 ppm U] and an additional inferred resource of 6.587 Mlbs of U_3O_8 [~2530 t U] at an average grade of 904 ppm [~767 ppm U]. In accordance with the demand from Anatolia Energy bottle roll leach tests have been initiated in MTA laboratories to investigate the recovery values of low-grade uranium ore under in-situ leach conditions. Bottle roll leaching tests are performed on pulverized samples with representative lixiviant solution at ambient pressure and provide an initial evaluation of ore leachability with a rough estimate of recovery value. At the end of the tests by using 2 g/L NaHCO_3 and 0.2 g/L H_2O_2 more than 90% of uranium can pass into leach solution in 12 days. (author)

Recent Pilot Plant Experience on Alkaline Leaching of Low Grade Uranium Ore in India

Energy Technology Data Exchange (ETDEWEB)

Suri, A. K; Ghosh, S. K.; Padmanabhan, N. P.H., [Bhabha Atomic Research Centre, Mumbai (India)

2014-05-15

Uranium deposits in India are low grade and are relatively smaller in extent as compared to present worldwide commercial practice. So far, the vein type deposits of Singhbhum Thrust Belt (STB) are being exploited for meeting the Indian requirements of uranium. The deposits are currently processed by acid leaching in the mills located at Jaduguda and Turamdih near Jamshedpur in Jharkhand State of India. The deposits at Jaduguda and Narwapahar are being mined by underground mining and are processed in Jaduguda mill using airagitated Pachucas. The deposits at Banduhurang and Turamdih are being mined by open cast and underground mining respectively and are processed at Turamdih by acid leaching in mechanically agitated reactors. The occurrences of uranium in North East and Northern part of Kadapa basin are relatively moderate in size and are expected to be processed in the near future by acid leaching. Uranium is also found to occur near Tummalapalle in granitic and limestone host rocks in Southern part of Kadapa basin (Andhra Pradesh) and in Gogi in Bhima basin (Karnataka). The deposit in Tummalapalle is relatively lower in grade (≈ 0.042% U{sub 3}O{sub 8}) but is a reasonably large reserve, whereas that in Gogi is rich in uranium content (≈0.18% U{sub 3}O{sub 8}) but is relatively small reserve. Laboratory tests based on alkaline leaching have been carried out on both types of deposits. Studies for Tummalapalle deposits have been extended to pilot plant level and a complete flow sheet has been established with the regeneration and recirculation of lixiviants and recovery of sodium sulphate as a by-product. The process involves alkaline leaching under oxygen pressure in batch type and/or continuous leach reactor using sodium carbonate/bicarbonate as a leaching media and uranium is recovered as sodium diuranate. Based on the techno-economic evaluation of the process, an industrial scale mill (3 000 tonnes ore/day) is being set up at Tummalapalle in Andhra Pradesh

Extraction of uranium low-grade ores from Great Divide Basin, Wyoming. National Uranium Resource Evaluation

International Nuclear Information System (INIS)

Judd, J.C.; Nichols, I.L.; Huiatt, J.L.

1983-04-01

The US Bureau of Mines is investigating the leachability of carbonaceous uranium ore samples submitted by the DOE under an Interagency Agreement. Studies on eight samples from the Great Divide Basin, Wyoming, are the basis of this report. The uranium content of the eight ore samples ranged from 0.003 to 0.03% U 3 O 8 and contained 0.7 to 45% organic carbon. Experiments were performed to determine the feasibility of extracting uranium using acid leaching, roast-acid leaching and pressure leaching techniques. Acid leaching with 600 lb/ton H 2 SO 4 plus 10 lb/ton NaClO 3 for 18 h at 70 0 C extracted 65 to 83% of the uranium. One sample responded best to a roast-leach treatment. When roasting for 4 h at 500 0 C followed by acid leaching of the calcine using 600 lb/ton H 2 SO 4 , the uranium extraction was 82%. Two of the samples responded best to an oxidative pressure leach for 3 h at 200 0 C under a total pressure of 260 psig; uranium extractions were 78 and 82%

Mining the high grade McArthur River uranium deposit

International Nuclear Information System (INIS)

Jamieson, B.W.

2002-01-01

The McArthur River deposit, discovered in 1988, is recognized as the world's largest, highest grade uranium deposit, with current mineable reserves containing 255 million lb U 3 O 8 at an average grade of 17.33% U 3 O 8 . In addition the project has resources of 228 million pounds U 3 O 8 averaging 12.02% U 3 O 8 . Mining this high-grade ore body presents serious challenges in controlling radiation and in dealing with high water pressures. Experience from the underground exploration programme has provided the information needed to plan the safe mining of the massive Pelite ore zone, which represents the most significant source of ore discovered during the underground drilling programme, with 220 million pounds of U 3 O 8 at an average grade in excess of 17%. Non-entry mining will be used in the high-grade ore zones. Raise boring will be the primary method to safely extract the ore, with all underground development in waste rock to provide radiation shielding. Water will be controlled by grouting and perimeter freezing. The ore cuttings from the raise boring will be ground underground and pumped to surface as slurry, at an average daily production of 150 tonnes. The slurry will be transported to the Key Lake mill and diluted to 4% before processing. The annual production is projected to be 18 million lb U 3 O 8 . The paper focuses on the activities undertaken since discovery, including the initiation of the raise bore mining method utilized to safely mine this high grade ore body. Radiation protection, environmental protection and worker health and safety are discussed in terms of both design and practical implementation. (author)

Uranium ores of Kazakhstan as the most technologic source of a fissionable material

International Nuclear Information System (INIS)

Berikbolov, B.R.

1999-01-01

Kazakhstan as is known has unique deposits of uranium. Its resources composed a third part of the world resources. The most important part of resources having a practical value, is related with depression in southern regions of the Republic. By now more than 15 deposits are discovered and partially explored. These deposits from three uranium provinces - Shu-Sarysu, Syr-Darya and Ili. The ores occur in friable water-bearing sandy horizons of Cretaceous and Paleogene age between waterproof agrillaceous sediments at depth from 100 up to 600 m. Ore bodies thickness changes from 5 to 10 m at uranian average-grade 0.03-0.1 %. Width of band shaped ore bodies changes from tens meters to the one kilometers and extent changes from one kilometer up to many tens kilometers. The important feature of deposits is their suitability for development by progressive in situ leaching (ISL) method. It was demonstrated, that uranium ores are comprehensive and, that is important, a lot of commercially important elements, containing in ores, gives in to extraction at development by the ISL method. The preliminary calculation of expenditures for the extraction of useful byproducts from ordinary sulphate solution have demonstrated rather high profitableness for rhenium, scandium, selenium, rare earth even at the very low contents in solution. It was pointed out, that whole technological chain applied now at industrial scale is oriented to mono-metallic uranium ores, therefore present technology of leaching and recovery of industrial solution does not allow ti extract all valuable components containing in ores. The development of new improved technological chain. beginning with a composition of leaching out reagent and up to applying of miscellaneous sorbing materials, can create new mineral-raw base of rare and dissipated elements and to lower considerably the price of uranium mining from sandstone deposits

Computer finds ore

Science.gov (United States)

Bell, Peter M.

Artificial intelligence techniques are being used for the first time to evaluate geophysical, geochemical, and geologic data and theory in order to locate ore deposits. After several years of development, an intelligent computer code has been formulated and applied to the Mount Tolman area in Washington state. In a project funded by the United States Geological Survey and the National Science Foundation a set of computer programs, under the general title Prospector, was used successfully to locate a previously unknown ore-grade porphyry molybdenum deposit in the vicinity of Mount Tolman (Science, Sept. 3, 1982).The general area of the deposit had been known to contain exposures of porphyry mineralization. Between 1964 and 1978, exploration surveys had been run by the Bear Creek Mining Company, and later exploration was done in the area by the Amax Corporation. Some of the geophysical data and geochemical and other prospecting surveys were incorporated into the programs, and mine exploration specialists contributed to a set of rules for Prospector. The rules were encoded as ‘inference networks’ to form the ‘expert system’ on which the artificial intelligence codes were based. The molybdenum ore deposit discovered by the test is large, located subsurface, and has an areal extent of more than 18 km2.

Extraction of metals from ores by bacterial leaching: present status and future prospects

International Nuclear Information System (INIS)

Kelly, D.P.

1977-01-01

The principal organism effecting bacterial leaching of ferrous and sulfide ores is Thiobacillus ferrooxidans, though other thiobacilli and other bacteria may be involved. The process depends on (a) direct solubilization of metal sulfides by bacterial oxidation; (b) dissolution of metal sulfides or oxides by ferric iron produced by bacterial pyrite oxidation. Mining spoil dumps and low grade ores can be leached for copper or uranium by cheap low-level technology. Dump leaching enables maximum recovery of valuable metal from any ore, but makes possible exploitation of very low grade Cu and U ores. Continuous extraction processes are possible where a continuously growing bacterial culture is fed with pyritic ores (or FeSO 4 or other sulfide) and continuous metal solubilization proceeds. Intimate contact between the bacteria and the ore to be leached (especially with uranium oxide ores) is not always necessary: leaching of UO 2 ores probably depends only on ferric iron reaction with the ore. Degradation of pyrite-containing rocks may also be developed as part of future recovery processes for petroleum from oil shales. Two-stage leaching systems present the best prospect for developing a higher-level technology for metal extraction. State 1: bacterial generation of Fe 3+ from pyrite or a Fe 2+ source; Stage 2: chemical leaching of ore by Fe 3+ in acid solution. Two-stage processes can be surface processes using crushed or milled ores or can be applied to underground solution mining, when an ore (e.g. uranium) can be leached by pumping Fe 3+ solutions through shattered underground deposits, metal recovered (e.g. solvent extraction) and Fe 3+ regenerated by bacterial oxidation at the surface. The use of controlled continuous microbial cultures to generate either bacteria or ferric iron is outlined

Comparison of oxidants in alkaline leaching of uranium ore

International Nuclear Information System (INIS)

Sreenivas, T.; Rajan, K.C.; Srinivas, K.; Anand Rao, K.; Manmadha Rao, M.; Venkatakrishnan, R.R.; Padmanabhan, N.P.H.

2007-01-01

The uranium minerals occurring in various ore deposits consists of predominantly uranous ion (U +4 ), necessitating use of an oxidant and other lixiviants for efficient dissolution during leaching. Unlike acid leaching route, where uranium minerals dissolution could be achieved efficiently with cheaper lixiviants, processing of ores by alkaline leaching route involve expensive lixiviants and drastic leaching conditions. Alkaline leaching of uranium ores becomes economical only upon using cheaper and efficient oxidants and conservation of other reagents by their recycle. The present paper gives efficacy of various oxidants - KMnO 4 , NaOCl, Cu - NH 3 , air and oxygen, in the leaching of uranium from a low-grade dolostone hosted uranium ore of India. A comparison based on technical merits and cost of the oxidant chemicals is discussed. (author)

Inhalation of uranium ores

International Nuclear Information System (INIS)

Stuart, B.O.; Jackson, P.O.

1975-01-01

In previous studies the biological dispositions of individual long-lived alpha members of the uranium chain ( 238 U, 234 U and 230 Th) were determined during and following repeated inhalation exposures of rats to pitchblende (26 percent U 3 O 8 ) ore. Although finely dispersed ore in secular equilibrium was inhaled, 230 Th/ 234 U radioactivity ratios in the lungs rose from 1.0 to 2.5 during 8 weeks of exposures and increased to 9.2 by four months after cessation of exposures. Marked non-equilibrium levels were also found in the tracheobronchial lymph nodes, kidneys, liver, and femur. Daily exposures of beagle dogs to high levels of this ore for 8 days resulted in lung 230 Th/ 234 U ratios of >2.0. Daily exposures of dogs to lower levels (0.1 mg/1) for 6 months, with sacrifice 15 months later, resulted in lung and thoracic lymph node 230 Th/ 234 U ratios ranging from 3.6 to 9 and nearly 7, respectively. The lungs of hamsters exposed to carnotite (4 percent U 3 O 8 ) ore in current lifespan studies show 230 Th/ 234 U ratios as high as 2.0 during daily inhalation of this ore in secular equilibrium. Beagle dogs sacrificed after several years of daily inhalations of the same carnotite ore plus radon daughters also showed marked non-equilibrium ratios of 230 Th/ 234 U, ranging from 5.6 to 7.4 in lungs and 6.2 to 9.1 in thoracic lymph nodes. This pattern of higher retention of 230 Th than 234 U in lungs, thoracic lymph nodes, and other tissues is thus consistent for two types of uranium ore among several species and suggests a reevaluation of maximum permissible air concentrations of ore, currently based only on uranium content

China's emergence as the world's leading iron-ore-consuming country

Science.gov (United States)

Kirk, W.S.

2004-01-01

China has become the leading iron ore consuming nation, and, based on recent steel production capacity increases and plans for more, its consumption will almost certainly to continue to grow. China's iron ore industry, however, faces a number of problems. China's iron ore is low-grade, expensive to process, and its mines are being depleted. For many Chinese steelmakers, particularly in the coastal regions, the delivered cost of domestic iron ore, is more than the delivered cost of foreign ore. Thus China's iron ore imports are expected to increase. As China's growth continues, it will almost certainly surpass Japan to become the leading iron ore importing country as well. Without China's increasing appetite for iron ore, the world iron ore market would be flat or declining. China's recent imports largely offset the slump in demand in North America and Europe. China is regarded by the iron ore industry as the growth sector for the next decade. Although Chinese imports are expected to continue their rapid increase and imports in other Asian countries are expected to continue growing, there appears to be enough greenfield and expansion projects to meet future demand for iron ore worldwide. Present suppliers of iron ore, Australia, Brazil, India, and South Africa, will probably be the chief beneficiaries of China's increasing consumption of iron ore. How long China can continue its extraordinary growth is the primary issue for the future of the iron ore industry. Based on the number and size of planned blast furnaces it appears that China's growth could continue for several more years. ?? 2004 Taylor and Francis.

Advantage of uranium contained in low grade dolomite ore

International Nuclear Information System (INIS)

Carneiro, A.L.M.

1988-01-01

The purpose of this work is to investigate a technological route to recover uranium from a lean mineral ore. The experimental work includes studies concerning calcination, carbonate leaching, settling, filtration and resin-ion-exchange. Experimental data confirm the technological feasibility of the proposed process and two different preliminary flowsheets of a pilot plant were suggested. (author) [pt

[Assessment of Soil Fluorine Pollution in Jinhua Fluorite Ore Areas].

Science.gov (United States)

Ye, Qun-feng; Zhou, Xiao-ling

2015-07-01

The contents of. soil total fluorine (TF) and water-soluble fluorine (WF) were measured in fluorite ore areas located in Jinhua City. The single factor index, geoaccumulation index and health risk assessment were used to evaluate fluorine pollution in soil in four fluorite ore areas and one non-ore area, respectively. The results showed that the TF contents in soils were 28. 36-56 052. 39 mg.kg-1 with an arithmetic mean value of 8 325.90 mg.kg-1, a geometric mean of 1 555. 94 mg.kg-1, and a median of 812. 98 mg.kg-1. The variation coefficient of TF was 172. 07% . The soil WF contents ranged from 0. 83 to 74. 63 mg.kg-1 with an arithmetic mean value of 16. 94 mg.kg-1, a geometric mean of 10. 59 mg.kg-1, and a median of 10. 17 mg.kg-1. The variation coefficient of WF was 100. 10%. The soil TF and WF contents were far higher than the national average level of the local fluorine epidemic occurrence area. The fluoride pollution in soil was significantly affected by human factors. Soil fluorine pollution in Yangjia, Lengshuikeng and Huajie fluorite ore areas was the most serious, followed by Daren fluorite ore area, and in non-ore area there was almost no fluorine pollution. Oral ingestion of soils was the main exposure route. Sensitivity analysis of model parameters showed that children's weight exerted the largest influence over hazard quotient. Furthermore, a significant positive correlation was found among the three kinds of evaluation methods.

Flotation study on scheelite ore of chitral khyber pakhtoonkhwa, pakistan

International Nuclear Information System (INIS)

Bhatti, M.A.; Kazmi, K.R.; Mehmood, R.; Akram, A.

2014-01-01

The beneficiation of a siliceous scheelite ore of Chitral, Khyber Pakhtoonkhwa, Pakistan, was investigated by flotation process to determine the optimum conditions for obtaining maximum grade and recovery of the scheelite concentrate. The variables studied were including pH and pulp density maintained during conditioning, type and quantity of reagents added, conditioning time and froth collecting time. The results achieved were plotted against the grade and recovery of the rougher concentrate. Several methods of cleaning rougher concentrate were attempted. An ore initially containing 0.34% WO/sub 3/ was upgraded into a final concentrate assaying 64.66% WO/sub 3/ with 70.36% recovery. The tungsten concentrate obtained meets the specifications required to produce ferrotungsten and tungsten chemicals. (author)

On-stream analysis of iron ore and its potential for improving export quality control

International Nuclear Information System (INIS)

Holmes, R.J.

1988-01-01

An on-stream iron ore analyser has been developed in collaboration with Hamersley Iron Pty. Limited for determining the iron content of both lump (-30+6 mm particle size) and fines (-6 mm particle size) on conveyor belts. The analyser, which is called IRONSCAN, is based on pair production, and is now commercially available from Mineral Control Instrumentation Limited (MCI) in Adelaide. It can be mounted under existing conveyor belts with minimal modifications to the conveyor structure, and the presence of steel cables in the belt does not interfere once the analyser has been correctly calibrated. The analyser has been extensively tested on both lump and fines on the shiploading conveyor at Dampier, and typically the root mean square (r.m.s.) deviation between single IRONSCAN measurements and conventional chemical analyses is better than 0.5% Fe. It is currently being evaluated on - 150 mm ore from the primary crusher at Mount Tom Price, and initial results are encouraging. The principal advantage of IRONSCAN is that it provides rapid information on ore grades. But perhaps its greatest potential is at the primary crusher where conventional sampling and analysis is very expensive to implement. 11 figs., 1 tab

Economic evaluation of preconcentration of uranium ores

International Nuclear Information System (INIS)

1981-04-01

The economics of two options for the preconcentration of low-grade uranium ores prior to hydrochloric acid leaching were studied. The first option uses flotation followed by wet high-intensity magnetic separation. The second option omits the flotation step. In each case it was assumed that most of the pyrite in the ore would be recovered by froth flotation, dewatered, and roasted to produce sulphuric acid and a calcine suitable for acid leaching. Savings in operating costs from preconcentration are offset by the value of uranium losses. However, a capital saving of approximately 6 million dollars is indicated for each preconcentration option. As a result of the capital saving, preconcentration appears to be economically attractive when combined with hydrochloric acid leaching. There appears to be no economic advantage to preconcentration in combination with sulphuric acid leaching of the ore

Investigation and analysis to the content of natural radionuclides at rate-earth ore and solid waste in China through the first nationwide pollution source survey

International Nuclear Information System (INIS)

Lou Jianjun; Liu Guifang; Sun Qinghong

2011-01-01

China has launched the First Nationwide Pollution Source Survey (FNPSS) during 2006-2009. Ministry Environmental Protection (MEP) sponsored the campaign of measuring the natural radionuclide contents. And the Ministry Environmental Protection (MEP) organized the measurements of natural radionuclide contents of in the factories and mines associated with rare-earth, niobium/tantalum, zircon, tin, lead/zinc, copper, iron, phosphate, coal, aluminum and vanadium. This paper analyzes mainly the data on the contents of U, 232 Th and 226 Ra in the rare-earth ore and solid waste produced by the rare-earth industry in China, as one of a series of papers on naturally occurring radioactive materials (NORM) s investigation. It is concluded that the average of the U, 232 Th and 226 Ra for the monazite sand of rare-earth ore is 16911, 49683, and 20072 Bq/kg, respectively. The average of U, 232 Th and 226 Ra in bastnaesite is 42, 701 and 91 Bq/kg, respectively. The average of U, 232 Th and 226 Ra in the ionic type rare-earth ore is 3918.6, 2315 and 1221 Bq/kg, respectively. (authors)

Determination of gold in gold ores

International Nuclear Information System (INIS)

Keedy, C.R.; Parson, L.; Shen, J.

1989-01-01

The gold content of placer gold flakes and gold bearing ores was determined by instrumental and radiochemical neutron activation analysis, respectively. It was discovered that significant errors result in the instrumental method for gold flakes as small as 10 mg due to sample self-absorption of neutrons during irradiation. Reliable results were obtained for both ore samples and gold flakes by dissolving the samples in aqua regia prior to irradiation. (author) 7 refs.; 3 tabs

CHARACTERIZATION OF METAL GRADES IN A STOCKPILE OF AN IRON MINE (CASE STUDY- CHOGHART IRON MINE, IRAN

Directory of Open Access Journals (Sweden)

Francesco Tinti

2018-01-01

Full Text Available In any mining operation due to the cut-off grade (economic criteria, materials classify into the ore and waste. The material with grade equal to or higher than the cut-off grade is considered as ore and the material with grade less than the cut-off grade is transported as wastes to the waste dumps. However, because of increasing metal demand, depleting of in situ ore reserves and so the reduction of cut-off grades for many metals, the mentioned waste dumps were considered as valuable ore reserves named stockpiles. In this paper, multivariate geostatistics was used to estimate the iron grades of two stockpiles following the sequential of piling procedures from the main source - the ore deposit - to the piling field. One stockpile is characterized by phosphorous concentration ((P % > 0.6 %, while the other by iron concentration ((Fe %< 50%. Since economic and physical constraints made sampling physically and economically problematic, the grade distribution and variability were estimated on the basis of primary blast-hole data from the main ore body and the mine’s long-term planning policy. A geostatistical model was applied to the excavated part of the iron deposit and the stockpile, by reconstructing ore selection, haulage and piling method. Results were validated through spatial variability of iron and phosphorous concentrations by comparing grade variability (Fe and P with mining and pilling units. This methodology allows characterizing the iron grades within stockpiles without any extra sampling.

The potentialities of nuclear geophysical methods in ore testing of ferrous metals

International Nuclear Information System (INIS)

Ochkur, A.P.; Voznesenskij, L.I.; Fedorov, S.V.

1976-01-01

To study iron ores of simple composition, the gamma-gamma method is used successfully, determining iron contents in boreholes, in the walls of mine workings and in sampling hacked off rocks. The X-ray diffraction method is used effectively in analysing iron ores of complex composition ensuring that the contents of Fe, Mn and Ca are determined in them. Neutron-capture spectrometric gamma-logging is a promising method for determining the total iron content in the mined ore. Manganese ores are singled out in the boreholes by data from thermal neutron and neutron-activation logging. The X-ray diffraction method is used to analyse powder samples in mine workings. To single out and estimate chromites in boreholes, a combination of neutron-capture spectrometric gamma-logging, gamma-gamma logging and epithermal neutron-neutron logging is used. The X-ray diffraction method determines the contents of Cr, Ca and Fe in powder and coarse-ground samples of chromites

Improvements on heap leaching process for a refractory uranium ore and yellow cake precipitation process

International Nuclear Information System (INIS)

Feng Jianke

2013-01-01

Some problems such as formed harden matrix, ore heap compaction, poor permeability, and agglomeration of absorption resin occur during extracting uranium from a refractory uranium ore by heap leaching process. After some measures were taken, i.e. spraying a new ore heap by low concentration acid, two or more ore heaps in series leaching, turning ores in ore heap, the permeability was improved, acid consumption was reduced. Through precipitate circulation and aging, the yellow cake slurry in amorphous or microlite form was transformed to crystal precipitate, thus uranium content in yellow cake was improved, and water content in yellow cake was lowered with good economic benefits. (author)

The comparative study of contents of zinc and lead in ore samples of Namtu-Bawdwin Mine by wet analysis, X-ray fluorescence and X-ray diffraction methods

Energy Technology Data Exchange (ETDEWEB)

Kyaw-Soe,

1990-05-01

Lead-zinc ores taken from Namtu-Bawdwin area had been analyzed by wet processes in the Department of Chemistry, 1984. These ore samples have been analyzed by energy dispersive X-ray fluorescence method in the Department of Physics and X-ray diffraction method is also used to determine elements of lead and zinc compounds in these ore samples in the University`s Research Centre. In brief, we study comparatively the contents of lead and zinc and their compounds using the methods of wet processes, X-ray fluorescence and X-ray diffraction. (author).

Applying Four Different Risk Models in Local Ore Selection

International Nuclear Information System (INIS)

Richmond, Andrew

2002-01-01

Given the uncertainty in grade at a mine location, a financially risk-averse decision-maker may prefer to incorporate this uncertainty into the ore selection process. A FORTRAN program risksel is presented to calculate local risk-adjusted optimal ore selections using a negative exponential utility function and three dominance models: mean-variance, mean-downside risk, and stochastic dominance. All four methods are demonstrated in a grade control environment. In the case study, optimal selections range with the magnitude of financial risk that a decision-maker is prepared to accept. Except for the stochastic dominance method, the risk models reassign material from higher cost to lower cost processing options as the aversion to financial risk increases. The stochastic dominance model usually was unable to determine the optimal local selection

Current methods and possibilities to determine the variability of Cu content in the copper ore on a conveyor belt in one of KGHM Polska Miedz S.A. mines

Directory of Open Access Journals (Sweden)

Jurdziak Leszek

2016-01-01

Full Text Available In this paper the methodology of ore sampling on a belt conveyor in one of KGHM Polska Miedz S.A. mines was presented together with the results of analysis of the variation of ore tonnage and quality. The ore was transferred from one mine to another one through the analysed transfer conveyor on the route from the mine Division of Mining to copper plants. The transported ore was sampled in person from Division of Concentrators on a regular basis for metal accounting purposes between both mines. The ore quality control became a significant problem since it is impossible to predict with satisfactory advance both Cu content in the feed as well as its lithology composition which is required to improve and optimise the enrichment efficiency.

Beneficiation studies of Bajaur manganese ore by different processing techniques

International Nuclear Information System (INIS)

Riaz, M.; Khan, F.U.; Yamin, A.; Bilquees, R.; Muhammad, N.

2010-01-01

The manganese ore of Bajaur Agency of Pakistan was subjected to flotation, heavy medium separation, gravity concentration and magnetic separation techniques for beneficiation. The original composition of the manganese ore was 45.56% Mn , 4% Fe/sub 2/O/sub 3/, 40% SiO/sub 2/. The Mn content was raised to a maximum 48.76 % in the concentrate with the recovery of 67.78 % through flotation technique. Other techniques rendered marginal increase in Mn concentration against the theoretical possibility of substantial enrichment by rejecting the 20 % gangue minerals. The separation of manganese minerals from associated gangue was difficult, due to mineralogical complexity of the ore, extreme fineness of the particle size, texture and minerals intergrowth. High Mn/Fe ratio, phosphorus, and silica contents were within tolerable limits for utilisation of the ore in ferro-manganese production. (author)

Optimization of flotation variables for the recovery of hematite particles from BHQ ore

Science.gov (United States)

Rath, Swagat S.; Sahoo, Hrushikesh; Das, B.

2013-07-01

The technology for beneficiation of banded iron ores containing low iron value is a challenging task due to increasing demand of quality iron ore in India. A flotation process has been developed to treat one such ore, namely banded hematite quartzite (BHQ) containing 41.8wt% Fe and 41.5wt% SiO2, by using oleic acid, methyl isobutyl carbinol (MIBC), and sodium silicate as the collector, frother, and dispersant, respectively. The relative effects of these variables have been evaluated in half-normal plots and Pareto charts using central composite rotatable design. A quadratic response model has been developed for both Fe grade and recovery and optimized within the experimental range. The optimum reagent dosages are found to be as follows: collector concentration of 243.58 g/t, dispersant concentration of 195.67 g/t, pH 8.69, and conditioning time of 4.8 min to achieve the maximum Fe grade of 64.25% with 67.33% recovery. The predictions of the model with regard to iron grade and recovery are in good agreement with the experimental results.

Application of X-ray luminescence separation to preliminary enrichment of lean scheelite-containing ores

International Nuclear Information System (INIS)

Zhaboev, M.N.; Semochkin, G.A.; Blinov, Yu.I.; Dzhambaev, F.M.; Novikov, V.V.; Tereshchenko, S.V.

1987-01-01

Investigations of preliminary enrichment of lean ores of amphibole hornfels by the method of X-ray luminescence separation was conducted. Pile and enriched products with different WO 3 content were obtained from these ores; WO 3 content in pile products was 2-2.5 times lower as compared to factory tailing products. WO 3 content in separator concentrate corresponds in all cases to the requirements for the ore designated for flotation enrichment. Carbonate modulus decreases 2.5-4 times in separation concentrate, simplifying the conditions of flotation

A New Heterotrophic Strain for Bioleaching of Low Grade Complex Copper Ore

Directory of Open Access Journals (Sweden)

Kaijian Hu

2016-02-01

Full Text Available A new heterotrophic strain, named Providencia sp. JAT-1, was isolated and used in bioleaching of low-grade complex copper ore. The strain uses sodium citrate as a carbon source and urea as a nitrogen source to produce ammonia. The optimal growth condition of the strain is 30 C, initial pH 8, sodium citrate 10 g/L and urea 20 g/L, under which the cell density and ammonia concentration in the medium reached a maximum of 4.83 × 108 cells/mL and 14 g/L, respectively. Ammonia produced by the strain is used as the main lixiviant in bioleaching. Bioleaching results revealed that higher strain growth led to a higher copper recovery, while higher pulp density will cause a greater inhibitory effect on strain growth and ammonia production. The copper extraction reached the highest value of 54.5% at the pulp density of 1%. Malachite, chrysocolla and chalcocite are easy to leach out in this bioleaching system while chalcopyrite is difficult. Results of comparative leaching experiments show that bioleaching using JAT-1 is superior to ammonia leaching at the same condition. The metabolites produced by the strain other than ammonia are also involved in bioleaching.

Research On Technology Of Making Rare Earth Alloy Having Rare Earth Content ≽30% From Ore (≽40% REO) Using Aluminum Thermal Technology In Arc Furnace

International Nuclear Information System (INIS)

Ngo Xuan Hung; Ngo Trong Hiep; Tran Duy Hai; Nguyen Huu Phuc

2014-01-01

Arc furnace was used to smelt materials consisting of rare earth ore having rare earth content of ≽40% REO, aluminum as the reducing agent and additives. Rare earth alloy was obtained with rare earth metal content of more than 30%. (author)

Measurements of CaF2 concentration in fluorite ore using thermoluminescence techniques

International Nuclear Information System (INIS)

Lembo, L.; Maestri, G.; Pimpinella, M.; Benzi, V.; Muntoni, C.

1990-01-01

Fluorite powder is produced by means of a flotation process on crude ore extracted by the mines. A full automation of the flotation plant would reduce the operating cost and improve the quality and recovery of fluorite production. However, taking into account that the efficiency of a flotation cycle is directly dependent on the CaF 2 content in the concentrate and tail products, this automation requires a quasi-real-time quantitative analysis of CaF 2 concentration in the floated pulp. The feasibility was studied of using a thermoluminescence technique as an on-line analysis method to measure the CaF 2 concentration during the flotation cycle. A first set of experimental conditions to determine CaF 2 content in acid-grade fluorspar has been already developed and the preliminary results so far obtained are presented. (author)

Commercial development of a new process of uraniferous ore sintering by pelletizing before dump leaching (wet process) application to a very clayey ore of Nord-Aquitaine

International Nuclear Information System (INIS)

Videau, G.; Roche, M.

1990-01-01

Much of the French uranium ore contains clay of sedimentary origin or derived from the alteration of rocks of the granite type. During a dump leaching operation by a wet process, these clays reduce the percolation rates and sometimes the percolation rates are so low that the very essence of the dump leaching operation can be called in question. This problem arises particularly for the treatment of the ore of Nord-Aquitaine. The results of tests, carried out at the SEPA in Bessines, have shown that after pelletizing clayey ores with sodium silicate in the presence of sulphuric acid for the polymerization of the silicate, the percolation rates were much increased. This new method was successfully applied, from a laboratory column to a pilot dump of 500 tonnes for the very clayey ore of Nord-Aquitaine. This ore of low grade (approx. 1000 ppm of U) seems to be difficult to upgrade by any other method of treatment in the present economic context [fr

Chloride pyrometallurgy of uranium ore. 1. Chlorination of phosphate ore using solid or gas chlorinating agent and carbon

International Nuclear Information System (INIS)

Taki, Tomihiro; Komoto, Shigetoshi; Otomura, Keiichiro; Takenaka, Toshihide; Sato, Nobuaki; Fujino, Takeo.

1995-01-01

A thermodynamical and pyrometallurgical study to recover uranium from the phosphate ores was undertaken using the chloride volatilization method. Iron was chlorinated with solid chlorinating agents such as NaCl and CaCl 2 in combination with activated carbon, which will be used for removing this element from the ore, but uranium was not. On the other hand, the chlorination using Cl 2 gas and activated carbon gave a good result at 1,223 K. Not only uranium but also iron, phosphorus, aluminum and silicon were found to form volatile chlorides which vaporized out of the ore, while calcium remained in the ore as non-volatile CaCl 2 . The chlorination condition was studied as functions of temperature, reaction time and carbon content. The volatilization ratio of uranium around 95% was obtained by heating the mixture of the ore and activated carbon (35 wt%) in a mixed gas flow of Cl 2 (200 ml/min) and N 2 (200 ml/min) at 1,223 K for 120 min. (author)

Utilisation of iron ore tailings as aggregates in concrete

OpenAIRE

Francis Atta Kuranchie; Sanjay Kumar Shukla; Daryoush Habibi; Alireza Mohyeddin

2015-01-01

Sustainable handling of iron ore tailings is of prime concern to all stakeholders who are into iron ore mining. This study seeks to add value to the tailings by utilising them as a replacement for aggregates in concrete. A concrete mix of grade 40 MPa was prepared in the laboratory with water–cement ratio of 0.5. The concrete were cured for 1, 2, 3, 7, 14 and 28 days. The properties of the concrete such as workability, durability, density, compressive strength and indirect tensile strength we...

Fe extraction from çayeli copper ores by bioleaching with eco freiendly acidithiobacillus ferrooxidans

International Nuclear Information System (INIS)

Kocadagistan, M.E.; Bayhan, Y.K.

2017-01-01

Recently, biological treatment; an important recovery process, has became important from the environmental and economical respects in recovery of metallic values from low-grade sulfur-bearing ores or concentrates. Bacterial ore leaching can be applied to extract heavy metals from low grade ores, industrial wastes and other materials on an industrial scale by different procedures. The main objective of this work was to investigate the dissolution of Fe from Çayeli copper ores, via a bioleaching process using Acidithiobacillus ferrooxidans. Experiments performed with batch operation in jar test equipment were conducted at different pH values, pulp densities, inoculum volumes, particle sizes, stirring conditions and operation times. The optimal parameters were found as follows; at pH 2, the pulp density; 4% (w/v), inoculum volume; 4% (v/v), stirring rate; 120 rpm and particle size; -0.053 mm for 192nd and 288th hours, at pH 2, the pulp density; 4% (w/v), inoculum volume; 5% (v/v), stirring speed; 200 rpm and particle size; -0.053 mm for 384th and 480th hours. By performing the bioleaching process under these conditions, almost 99% of the iron extent in the ore was transfer from ore into solution, however the experiments in which distilled water was used instead of modified 9K*, only 18.5% Fe efficiency was obtained. (author)

Radiation dose estimates from a mining plan for a high-grade uranium deposit

International Nuclear Information System (INIS)

Scott, L.M.

1981-01-01

The significance of gamma exposure to uranium miners has been recognized only in the last few years. Most ore deposits which have been underground mined, were 1% or less U 3 O 8 . Full-time mining of this grade ore can result in exposure exceeding 1 Rem per year. Several companies in Saskatchewan are planning to mine recently discovered ore bodies which contain ore pods in excess of 10% U 3 O 8 . The purpose of this paper is to present dose data which can be used to estimate gamma exposure from high-grade ore deposits, and to present mining techniques which will minimize miner exposure

Heap leaching of clay ish uranium ores

International Nuclear Information System (INIS)

Gonzalez, E.; Sedano, A.

1973-01-01

This paper describes an experimental facility, built near El Lobo mine. In it we study the beneficiation of low-grade uranium ore. The mineral has a great amount of clay and fines. The flow-sheet used has four steps: head leaching, ph-ajustement, ion-exchange and participation. We show, also, the most interesting results. (Author)

Thorium content of a mineral ore from Morro do Ferro by fission track technique

International Nuclear Information System (INIS)

Oliveira, C.A.N. de.

1980-10-01

The feasibility to determine thorium concentrations by fission track technique in samples of mineral ore has been demonstrated. The literature registers only the application of the fission track technique to mineral ore in the case where the fissionable element is uranium. The technique was applied to determine the thorium concentration of an ore sample from Morro do Ferro, taking advantage of the high thorium to uranium ratio in that mineral. The sample analysed presented a thorium concentration of 2467 +- 400 mg Th/Kg ore. The so called wet method was adopted by using the Bayer made Makrofol KG 10μm thick, as the detector foil, immersed in the thorium solution. The technique is also useful to determine thorium concentrations in environmental samples because of the following aspects: high sensitivity; fast chemical separation of interfering elements; low cost; and operational simplicity. (Author) [pt

Uranium abundance in some sudanese phosphate ores

International Nuclear Information System (INIS)

Adam, A.A.; Eltayeb, M.A.H.

2009-01-01

This work was carried out mainly to analysis of some Sudanese phosphate ores, for their uranium abundance and total phosphorus content measured as P 2 O 5 %. For this purpose, 30 samples of two types of phosphate ore from Eastern Nuba Mountains, in Sudan namely, Kurun and Uro areas were examined. In addition, the relationship between uranium and major, and trace elements were obtained, also, the natural radioactivity of the phosphate samples was measured, in order to characterize and differentiate between the two types of phosphate ores. The uranium abundance in Uro phosphate with 20.3% P 2 O 5 is five time higher than in Kurun phosphate with 26.7% P 2 O 5 . The average of uranium content was found to be 56.6 and 310 mg/kg for Kurun and Uro phosphate ore, respectively. The main elements in Kurun and Uro phosphate ore are silicon, aluminum, and phosphorus, while the most abundant trace elements in these two ores are titanium, strontium and barium. Pearson correlation coefficient revealed that uranium in Kurun phosphate shows strong positive correlation with P 2 O 5 , and its distribution is essentially controlled by the variations of P2O5 concentration, whereas uranium in Uro phosphate shows strong positive correlation with strontium, and its distribution is controlled by the variations of Sr concentration. Uranium behaves in different ways in Kurun phosphate and in Uro phosphate. Uro phosphate shows higher concentrations of all the estimated radionuclides than Kurun phosphate. According to the obtained results, it can be concluded that Uro phosphate is consider as secondary uranium source, and is more suitable for uranium recovery, because it has high uranium abundance and low P 2 O 5 %, than Kurun phosphate. (authors) [es

PGAA method for control of the technologically important elements at processing of sulfide ores

International Nuclear Information System (INIS)

Kurbanov, B.I.; Aripov, G.A.; Allamuratova, G.; Umaraliev, M.

2006-01-01

Full text: Many precious elements (Au, Re, Pt, Pd, Ag, Cu, Ni, Co, Mo) in ores mainly exist in the form of sulfide minerals and the flotation method is often used for processing of such kind of ores. To enhance the efficiency of the process it is very important to carry out the operative control of the elements of interest at various stages of ore processing. In this work the results of studies for developing methods for control of technologically important elements at processing and enrichment sulfide ores, which content the gold, copper, nickel, molybdenum in the ore-processing plants of Uzbekistan. The design of transportable experimental PGAA device on the basis of low-power radionuclide neutron source ( 252 Cf) with neutrons of 2x10 7 neutr/sec allowing to determine element content of the above named ores and their processing products is offered. It is shown that the use of the thermal neutron capture gamma-ray spectrometry in real samples and technological products allows prompt determination of such elements as S, Cu, Ti and others, which are important for flotation of sulfide ores. Efficiency control of the flotation processing of sulfide ores is based on quick determination of the content of sulfur and some other important elements at different stages of the process. It was found that to determine elements the following gamma lines are the most suitable - 840.3 keV for sulfur, 609 keV and 7307 keV for copper and 1381.5 keV, 1498.3 keV and 1585.3 keV for titanium. Based on the measurements of original ores, concentrates of various stages of flotation and flotation slime the possibility for prompt determination of S, Cu and Ti content and thus to get necessary information on the efficiency of the flotation process was shown. (author)

Sustainability of Water Cooled Reactors - Energy Balance for Low Grade Uranium Resources

International Nuclear Information System (INIS)

Strupczewski, A.

2011-01-01

The opponents of nuclear power claim that as uranium resources get exhausted the energy needed to mine low grade uranium ore will be larger than the energy that can be obtained from fission in a nuclear power plant. This would result in loss of sustainability of nuclear power, with the negative energy balance expected within the next 40-60 years. Since the opponents state clearly that the ore containing less than 0.013% U 3 O 8 cannot yield positive energy balance, the study of the Institute of Atomic Energy in Poland referenced three mines of decreasing ore grade: Ranger 0.234% U 3 O 8 , Rossing 0.028% U 3 O 8 and Trekkopje 0.00126% U 3 O 8 , that is with ore grade below the postulated cut off value. The study considered total energy needs for uranium mining, including not only electricity needed for mining and milling, for water treatment and delivery, but also fuel for transportation and ore crushing, explosives for rock blasting, chemicals for uranium leaching and the energy needed for mine reclamation after completed exploitation. It has been shown that the energy estimates of nuclear opponents are wrong for Ranger mine and go off much further for the mines with lower uranium ore grades. The reasons for erroneous reasoning of nuclear opponents have been found. Their errors arise from treating the uranium ore deposits as if their layout and properties were the same as those of uranium ore mined in the US in the 70-ies. This results in an oversimplified formula, which yields large errors when the thickness of the overlayer is less than it was in the US. In addition the energy needs claimed for mine reclamation are much too high. The study showed that the energy needed for very low grade uranium ore mining and milling increases but the overall energy balance of the nuclear fuel cycle remains strongly positive. (author)

Radiometric sorting of Rio Algom uranium ore

International Nuclear Information System (INIS)

Cristovici, M.A.

1983-11-01

An ore sample of about 0.2 percent uranium from Quirke Mine was subjected to radiometric sorting by Ore Sorters Limited. Approximately 60 percent of the sample weight fell within the sortable size range: -150 + 25 mm. Rejects of low uranium content ( 2 (2 counts/in 2 ) but only 7.6 percent of the ore, by weight, was discarded. At 0.8-0.9 counts/cm 2 (5-6 counts/in 2 ) a significant amount of rejects was removed (> 25 percent) but the uranium loss was unacceptably high (7.7 percent). Continuation of the testwork to improve the results is proposed by trying to extend the sortable size range and to reduce the amount of fines during crushing

The effects of mixtures of potassium amyl xanthate (PAX and isopropyl ethyl thionocarbamate (IPETC collectors on grade and recovery in the froth flotation of a nickel sulfide ore

Directory of Open Access Journals (Sweden)

Westhein Maree

2017-12-01

Full Text Available Potassium amyl xanthate (PAX and sodium isobutyl xanthate (SIBX are commonly used collectors in both the bulk and selective froth flotation of sulfide ores. These thiol xanthate collectors are conventionally mixed together as well as with more selective thiol collectors such as dithiophosphates (DTP and dithiocarbamates (DTC, in order to improve selectivity. With deteriorating nickel sulfide ores, more selective collectors and collector mixtures are desired for the efficient extraction of nickel. Thionocarbamates (TC are another group of thiol collectors used for selective froth flotation of sulfide minerals. Thionocarbamates are especially used in the selective froth flotation of chalcopyrite over pyrite and galena, but little is known about its selectivity with regards to nickel. Thionocarbamates are also more stable over larger pH ranges in comparison to xanthates and they possess beneficial frothing properties. This study compared the effects of using potassium amyl xanthate (PAX, isopropyl ethyl thionocarbamate (IPETC, sodium isobutyl xanthate (SIBX and their mixtures in the froth flotation of a pentlandite ore. In the mixtures of PAX or SIBX with IPETC, the xanthate accounted for 95.5 mol% and for the PAX and SIBX mixture a 50:50 mixture was used. This study showed that the highest cumulative nickel grades were obtained with PAX, SIBX and there mixture. The highest cumulative nickel recoveries were obtained with IPETC and its mixtures with PAX and SIBX (50–62%. Keywords: Nickel sulfide, Xanthate, Thionocarbamate, Grade, Recovery

Predicting the Concentration Characteristics of Itakpe Iron Ore for cut ...

African Journals Online (AJOL)

MICHAEL HORSFALL

ABSTRACT: Concentration characteristics of an ore are very critical to the estimation of cut-off grade of a ... enormous financial cost of laboratory analysis and time required for such .... Arua A.I. (1997) Fundamentals of statistics, Publisher,.

Study of the dry processing of uranium ores

International Nuclear Information System (INIS)

Guillet, H.

1959-02-01

A description is given of direct fluorination of pre-concentrated uranium ores in order to obtain the hexafluoride. After normal sulfuric acid treatment of the ore to eliminate silica, the uranium is precipitated by a load of lime to obtain: either impure calcium uranate of medium grade, or containing around 10% of uranium. This concentrate is dried in an inert atmosphere and then treated with a current of elementary fluorine. The uranium hexafluoride formed is condensed at the outlet of the reaction vessel and may be used either for reduction to tetrafluoride and the subsequent manufacture of uranium metal or as the initial product in a diffusion plant. (author) [fr

Geochemistry and ore prospecting

International Nuclear Information System (INIS)

Le Caignec, R.

1954-01-01

Applied geochemistry is a new technique which helps the geologist in detecting ore deposits. Some deposits, even when they are covered with rather thick surface structures, form around these zones where the infinitesimal content of some elements of soils or waters is notably different. These 'anomalies' may be contemporaneous to the deposit-structure (primary dispersion) or may have occurred later (secondary dispersion). Various factors rule these anomalies: ore-stability, soil homogeneity, water conditions, topography, vegetation, etc... Applied geochemistry is in fact the study of analysis techniques of metal traces in soils as well as the geological interpretation of observed anomalies. This report gives practical data on sampling methods, yields, costs and also on special problems of uranium geochemistry. (author) [fr

Valorization of mining waste from Ouenza iron ore mine (eastern Algeria

Directory of Open Access Journals (Sweden)

Abdelaziz Idres

Full Text Available Abstract The present article is devoted to the development of a hematite-poor ore mine in Ouenza, which does not meet the steelmaker's requirements. Significant volumes are stored at the pithead of the mine, and the reserves are estimated at over 100 million tones. This enormous quantity of mining waste occupies an important space and poses a real threat to the environment as well as for the mining city of Ouenza. In order to solve these socio-economic and environmental problems, a sustainable development and a better quality of life for inhabitants of this region is needed. For this, representative samples were taken at the level of the dumps. Taking into account the natural characteristics of the stock namely; mineralogical composition, iron content, particle size of the rock mass, as well as the release mesh of iron minerals from the gangue. Firstly, tests are conducted on the recovery by radiometric separation of iron-rich pieces and graded. Then the rest of the ore was subjected to mechanical preparation followed by enrichment, which will be the subject of another study. The research is conducted on samples to determine the optimal parameters of the g-rays absorption tested by radiometry; these parameters were the velocity of the conveyor belt and the time of exposure to g-rays. The obtained results by this valorization process are very significant: iron content 53.5% and 8.3% recovery.

Biohydrometallurgy and membrane technology for resource recovery from low-grade ores and mining residuals; Biohydrometallurgie und Membrantechnik zur Wertstoffgewinnung aus Armerzlagerstaetten und bergbaulichen Altablagerungen

Energy Technology Data Exchange (ETDEWEB)

Werner, Arite; Meschke, Katja; Bohlke, Kevin; Haseneder, Roland [TU Bergakademie Freiberg (Germany). Inst. fuer Thermische Verfahrenstechnik, Umwelt-, Naturstoffverfahrenstechnik (ITUN); Daus, Birgit [Helmholtz-Zentrum fuer Umweltforschung GmbH - UFZ, Leipzig (Germany). Dept. Analytik; Repke, Jens-Uwe [Technische Univ. Berlin (Germany). FG Dynamik und Betrieb Technischer Anlagen

2017-02-15

The recovery of strategic elements from secondary mineral resources and low grade ores is of increasing relevance, due to a changing global market as well as for reasons of sustainability. The present article shows the potential of biohydrometallurgy as an efficient technology for mobilization of metals from secondary mineral resources. Furthermore, the application of membrane separation as a successful technique for the recovery of metals from bioleaching solutions is presented. These issues are discussed within the scope of recent research projects.

Impact Of Low Grade Uranium Ores On The Echo System and the Workers of Phosphate Industry

International Nuclear Information System (INIS)

Anwar, S.M.

1999-01-01

The present study aims to investigate the influence of uranium present in phosphate rocks as an environmental factor in the ccho system and on the workers of Abu-Zaabal Phosphate Company subjected to the inhalation of big quantities of rock phosphate dust during the benefication of the ore and the production of the fertilizers. Besides. extra amount of uranium reach the workers also through two path ways.The first is direct through eating contaminated planted grown in the near by area.The second is indirect through eating animals fed with contaminated plants. The uranium content is estimated in the soil samples at different depths, water (irrigation and drainage), air samples and plant samples (shoot and root) in Berseem from the four directions, urine samples from twenty workers in charge of the processing of phosphate compared to twenty volunteers far from the contaminated area.The results showed an elevated values for phosphorus and uranium in the air, water. soil and plant (Berseem) around Abu Zaabal Factory and extending to about 2 km from all directions. Urine may be considered as a biological indicator medium for the uptake of uranium in uranium miners and the workers in charge of ore processing and can represent the major route of excretion for the absorbed metal. Significant differences were shown between the uranium level in the urine of workers group and the control group

Studies of leaching of copper ores and flotation wastes

International Nuclear Information System (INIS)

Wawszczak, D.; Deptula, A.; Lada, W.; Smolinski, T.; Olczak, T.; Brykala, M.; Wojtowicz, P.; Rogowski, M.; Milkowska, M.; Chmielewski, A.G.

2014-01-01

In Poland, there are significant deposits of copper ores. During the copper extraction, large amounts of flotation wastes are produced. In the ores and flotation wastes many other important elements are present. The main goal of this work was analysis of uranium content and to elaborate procedures for recovery of U from these materials. Two types of ores and four types of waste were examined. It has been found that uranium content varies from 4.5 to 25 ppm. The other elements have also been determined in these materials: Cu (4-5 % in ores and 0.3-1.7 % in waste), Ag, Re, Mo, La, Ni, V, etc. For leaching, sulfuric acid and sodium carbonates of various concentrations (temperature, time) were used. The optimum conditions for leaching have been found. The concentration of uranium in the final solution was generally less than 25 μg/mL. The other elements are also present in the leaching solutions. Simultaneous liquid-liquid extraction of uranium with these elements from leaching solution is under study. In our opinion, only such combined procedure for the recovery of uranium together with the accompanying elements could be cost-effective. (author)

Characterization and Beneficiation Studies of a Low Grade Bauxite Ore

Science.gov (United States)

Rao, D. S.; Das, B.

2014-10-01

A low grade bauxite sample of central India was thoroughly characterized with the help of stereomicroscope, reflected light microscope and electron microscope using QEMSCAN. A few hand picked samples were collected from different places of the mine and were subjected to geochemical characterization studies. The geochemical studies indicated that most of the samples contain high silica and low alumina, except a few which are high grade. Mineralogically the samples consist of bauxite (gibbsite and boehmite), ferruginous mineral phases (goethite and hematite), clay and silicate (quartz), and titanium bearing minerals like rutile and ilmenite. Majority of the gibbsite, boehmite and gibbsitic oolites contain clay, quartz and iron and titanium mineral phases within the sample as inclusions. The sample on an average contains 39.1 % Al2O3 and 12.3 % SiO2, and 20.08 % of Fe2O3. Beneficiation techniques like size classification, sorting, scrubbing, hydrocyclone and magnetic separation were employed to reduce the silica content suitable for Bayer process. The studies indicated that, 50 % by weight with 41 % Al2O3 containing less than 5 % SiO2 could be achieved. The finer sized sample after physical beneficiation still contains high silica due to complex mineralogical associations.

Radioactivity of phosphate ores from Karatas-Mazidag phosphate deposit of Turkey

International Nuclear Information System (INIS)

Akyuez, T.; Varinlioglu, A.; Kose, A.; Akyuez, S.

2000-01-01

The specific activities of 238 U, 226 Ra, 232 Th and 40 K in the composite samples of phosphate ores of type I (grey-coloured ore, with high P 2 O 5 (21-35%) and low calcite content) and of type II (grey coloured calcite ore, with low P 2 O 5 content (5-17%)) of Karatas-Mazidag phosphate deposit, Turkey, have been determined by gamma spectrometry together with phosphatic animal feed ingredients. The concentrations of 238 U, 226 Ra, 232 Th and 40 K were found to be up to 557, 625, 26 and 297 Bq x kg -1 , respectively. Radium equivalent activities of samples were calculated and compared with those given in the literature. Uranium concentration of the individual phosphate samples, from which composite samples of ores of type I and II have been prepared, were found to show and increasing trend with increasing P 2 O 5 and F concentrations. (author)

Ores and Climate Change - Primary Shareholders

Science.gov (United States)

Stein, Holly J.; Hannah, Judith L.

2015-04-01

many giant Cu-Mo-Au ore deposits may be arrested when the surface is catastrophically breached, as multiple km-scale breccia pipes empty their volatile and metal contents into the atmosphere. The new equation for studying ore geology should be one that reconstructs ore formation from beginning to end, that is, from source, release, and transport, to breach. Of course, detailed measurements and mapping of ore bodies remains essential, but a full understanding of metal migration and budgets can only be achieved if we model what might have been left behind in deeper Earth, and what may have been lost to the atmosphere. To do this, we need to understand much more than the geology at our ore deposit of interest. Stein, H.J. (2014) Dating and Tracing the History of Ore Formation. Treatise on Geochemistry 13: 87-118. Elsevier. Support for time to think - CHRONOS, funded by a consortium of Norwegian petroleum companies.

Characterizing the economic value of an epithermal Au-Ag ore with Laser Induced Breakdown Spectroscopy (LIBS)

NARCIS (Netherlands)

Dalm, M.; Buxton, M.W.N.

2016-01-01

LIBS was applied to 19 Au-Ag ore samples to investigate if this technique can be used to distinguish between economic and sub-economic ore either by direct detection of these elements or by using other elements as indicators. However, the Au and Ag grades of the samples are below the detection limit

Chemical treatment proceed of poor uranium content ores; Un procede de traitement chimique des minerais pauvres d'uranium

Energy Technology Data Exchange (ETDEWEB)

Mouret, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Pagny, P [Societe Potasse et Engrais Chimiques (France)

1955-07-01

The needs in uranium constantly increased inciting to develop new chemical processes for the treatment of uranium ores. we searched processes that permit to get this element from ores poor in uranium, to a reasonable cost price. We used a sulphuric attack and a precipitation of uranium as phosphate uranate or pyrophosphate uranate to separate its from the different impurities. The process permitted to process ores contents of about 0,05% of uranium and to get an end product of sodium carbonate uranate containing 60 to 65% of uranium, with an acceptable cost price and an extraction yield situated between 90 and 95%. (M.B.) [French] Les besoins sans cesse accrus en uranium ont incite de developper de nouveaux procedes chimiques pour le traitement de minerais uranifere. nous avons recherche des procedes qui permettent d'obtenir cet element a partir de minerais pauvres en uranium, a un prix de revient raisonnable. Nous nous sommes orientes vers une attaque sulfurique et une precipitation de l'uranium sous forme de phosphate uraneux ou de pyrophosphate uraneux pour le separer des differentes impuretes. Le procede a permis de descendre a des teneurs en uranium de l'ordre de 0,05 % et d'obtenir un produit final a l'etat d'uranate de soude contenant 60 e 65 % d'uranium, avec un prix de revient acceptable et avec un rendement global d'extraction situe entre 90 et 95 %. (M.B.)

Sinterization of manganese ore tailings under argon atmosphere

Energy Technology Data Exchange (ETDEWEB)

Valduga, M.M.F.; Lima, F.; Lima, R.M.F. [Universidade Federal de Ouro Preto (UFOP), MG (Brazil)

2014-07-01

Manganese is an element widely used in Metallurgy, however the Brazilian reserves has low grade. The aim of this work was to obtain and characterize the sinters from manganese ore tailings. The fines (less than 400⧣) were calcinated (800°C - 3600s) and homogenized with activated charcoal (7 and 10%) and CaO (5 and 10%). The sintering were carried out at 1135, 1140 and 1145°C during 7200 and 14400s under argon atmosphere. The sintered products were characterized by EDS analysis, BET surface area, apparent density, X-rays diffraction and SEM/EDS. The surface area was 0.03m2/g. The alkali element present (potassium) justified the low melting point of waste (1140°C). Due to the chemical complexity of the tailings, several phases were characterized in the products: pores, silicates with high content of manganese in the matrix, other silicates with different proportions of Al, Mn, Mg and Ca, pure Fe, SiO2, etc. (author)

The presentation of leaching and bio-leaching from different ores using SIMPLEX EVOP

OpenAIRE

Krstev, Boris; Krstev, Aleksandar; Golomeova, Mirjana; Gocev, Zivko

2013-01-01

The refractory or low grade lead/zinc domestic ores in Republic of Macedonia are investigated by conventional separation technology or flotation separation. In the mean time, investigations are directed to the new possibilities of leaching by microorganisms – bioleaching. The paper is result of these technologies and investigations carried out for recovery of in the mentioned ores. Using Simplex EVOP and computer program Multisimplex performances are appropriate and most acceptable and exce...

Siltation of Ore Particles in Leaching Tanks: Causative Factors and ...

African Journals Online (AJOL)

Michael

2016-12-02

Dec 2, 2016 ... In this era of low grade ores and low metal price regimes, most plants now ... factors for siltation of tanks in the Carbon-in-Leach. Plant of Gold Fields Ghana Ltd at ..... interests are in rare earth elements minerals beneficiation ...

Application of neutron activation analysis to control P2O5 content in ore and ore concentrates of ''Apatit'' works

International Nuclear Information System (INIS)

Belyakov, M.A.; Terent'eV, Eh.P.; Frolov, V.A.

1982-01-01

A technique for a neutron activation rapid analysis of fluorine is described. A mean-square error of the analysis makes up 0,g3 per cent F. The investigation has been carried out and a close correlation has been established for the Hibine massif exploited apatite deposits on the basis of the neutron activation analysis of fluorine and chemical analysis of P 2 O 5 . Possibilities are shown of using the neutron activation analysis of P 2 O 5 in ores and certain ore con-- centrates of ''Apatit'' works from the radioactivity induced in fluorine. A mean-square error of the analysis makes up 0,35 per cent P 2 O 5

Bioleaching of low-grade uranium ore using Acidithiobacillus ferrooxidans

International Nuclear Information System (INIS)

Pal, S.; Das, T.; Sukla, L.B.; Roy Chaudhury, G.; Pradhan, D.

2010-01-01

Bioleaching of uranium was carried out with Turamdih ore sample procured from Uranium Corporation of India Limited, Jaduguda. The bacterial strain that was used in the leaching experiments was isolated from the Jaduguda mine water sample. Efficiency of bioleaching was studied by varying parameters like pulp density and initial ferrous concentration as source of energy. It is observed that the efficiency of bioleaching was 49% at 10% pulp density (w/v) and initial pH 2.0. Addition of external has no effect on efficiency of bioleaching showing domination of direct leaching mechanism over indirect. (author)

Thermodynamic Analysis of the Selective Reduction of a Nickeliferous Limonitic Laterite Ore by Hydrogen

Science.gov (United States)

Elliott, R.; Pickles, C. A.

2017-09-01

Nickeliferous limonitic laterite ores are becoming increasingly attractive as a source of metallic nickel as the costs associated with recovering nickel from the sulphide ores increase. Unlike the sulphide ores, however, the laterite ores are not amenable to concentration by conventional mineral processing techniques such as froth flotation. One potential concentrating method would be the pyrometallurgical solid state reduction of the nickeliferous limonitic ores at relatively low temperatures, followed by beneficiation via magnetic separation. A number of reductants can be utilized in the reduction step, and in this research, a thermodynamic model has been developed to investigate the reduction of a nickeliferous limonitic laterite by hydrogen. The nickel recovery to the ferronickel phase was predicted to be greater than 95 % at temperatures of 673-873 K. Reductant additions above the stoichiometric requirement resulted in high recoveries over a wider temperature range, but the nickel grade of the ferronickel decreased.

Hydrometallurgical Processing Technology of Titanomagnetite Ores

Directory of Open Access Journals (Sweden)

Victor Ivanovich Sachkov

2017-12-01

Full Text Available In this paper, we study the possibility of obtaining iron and titanium-vanadium concentrates with highest contents of iron and titanium, respectively, through hydrometallurgical processing of the titanomagnetite ores of the Chineisk deposit. We varied two key parameters to determine the efficiency of the process: (a concentration of leaching solution (ammonium fluoride; and (b acidity of solution. Ammonium fluoride concentration was varied from 0.08 mol/L to 4.2 mol/L with the other fixed parameters. It was shown that optimum ammonium fluoride concentration for leaching the ore is 0.42 mol/L; at these concentrations iron and titanium contents are about 62.8 wt % and 3.5 wt % in solid phase, respectively. The acidity of solution was changed by adding of hydrofluoric acid with varied concentration (from 0.86 mol/L to 4.07 mol/L to ammonium fluoride solution with fixed concentration of 0.42 mol/L. The best results (degree of titanium extraction = 63.7% were obtained when using a solution of hydrofluoric acid with concentration 4.07 mol/L. In this case, the addition of acid makes it possible to increase the Fe/Ti ratio by 3.4 times in comparison with the original ore. Thus, we conclude that acidity and the concentration of ammonium fluoride solution significantly influences the selectivity of the hydrometallurgical process.

Extracting phosphoric iron under laboratorial conditions smelting bog iron ores

International Nuclear Information System (INIS)

Török, B; Thiele, A

2013-01-01

In recent years it has been indicated by archaeometric investigations that phosphoric-iron (P-iron, low carbon steel with 0,5-1,5wt% P), which is an unknown and unused kind of steel in the modern industry, was widely used in different parts of the world in medieval times. In this study we try to explore the role of phosphorus in the arhaeometallurgy of iron and answer some questions regarding the smelting bog iron ores with high P-content. XRF analyses were performed on bog iron ores collected in Somogy county. Smelting experiments were carried out on bog iron ores using a laboratory model built on the basis of previously conducted reconstructed smelting experiments in copies of excavated furnaces. The effect of technological parameters on P-content of the resulted iron bloom was studied. OM and SEM-EDS analyses were carried out on the extracted iron and slag samples. On the basis of the material analyses it can be stated that P-iron is usually extracted but the P-content is highly affected by technological parameters. Typical microstructures of P-iron and of slag could also be identified. It could also be established that arsenic usually solved in high content in iron as well

Determination of U (Ⅵ) content in uranium molybdenum ores

International Nuclear Information System (INIS)

Wang Haisheng; Ding Hongfang

2014-01-01

Potentionmetric titration is established to determine U (Ⅵ) in uranium molybdenum ores. In the closed condition, U (Ⅵ) is leached by carbonate solution. U (Ⅵ) is reduced to U (Ⅳ) by ferrous sulfate in phosphoric acid. The exess ferrous sulfate is oxidized by sodium nitrite. urea decompose the exess sodium nitrite. U (Ⅳ) is titrated by ammonium metavanadate standard solution with potentionmetric titration. The precision is better than 5%, The recovery rate is 97.2%∼101.9%. (authors)

New route for uranium concentrate production from Caetite ore, Bahia State, Brazil; dynamic leaching - direct precipitation

Energy Technology Data Exchange (ETDEWEB)

Morais, Carlos A. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mail: cmorais@cdtn.br; Gomiero, Luiz A.; Scassiotti Filho, Walter [Industrias Nucleares do Brasil S.A. (INB), Caetite, BA (Brazil)]. E-mails: gomiero@inb.gov.br; scassiotti@inb.gov.br

2007-07-01

The common uranium concentrate production consists of ore leaching, uranium purification/concentration by solvent extraction and uranium precipitation as ammonium diuranate steps. In the present work, a new route of uranium concentrate production from Caetite, BA-Brazil ore was investigated. The following steps were investigated: dynamic leaching of the ground ore with sulfuric acid; sulfuric liquor pre-neutralization until pH 3.7; uranium peroxide precipitation. The study was carried out in bath and continuous circuits. In the dynamic leaching of ground ore in agitated tanks the uranium content in the leached ore may be as low as 100 {mu}g/g U{sub 3}O{sub 8}, depending on grinding size. In the pre-neutralization step, the iron content in the liquor is decreased in 99 wt.%, dropping from 3.62 g/L to 0.030 g/L. The sulfate content in the liquor reduces from 46 g/L to 22 g/L. A calcinated final product assaying 99.7 wt.% U{sub 3}O{sub 8} was obtained. The full process recovery was over 94%. (author)

Linking leach chemistry and microbiology of low-grade copper ore bioleaching at different temperatures

Science.gov (United States)

Jia, Yan; Sun, He-yun; Tan, Qiao-yi; Gao, Hong-shan; Feng, Xing-liang; Ruan, Ren-man

2018-03-01

The effects of temperature on chalcocite/pyrite oxidation and the microbial population in the bioleaching columns of a low-grade chalcocite ore were investigated in this study. Raffinate from the industrial bioleaching heap was used as an irrigation solution for columns operated at 20, 30, 45, and 60°C. The dissolution of copper and iron were investigated during the bioleaching processes, and the microbial community was revealed by using a high-throughput sequencing method. The genera of Ferroplasma, Acidithiobacillus, Leptospirillum, Acidiplasma, and Sulfobacillus dominated the microbial community, and the column at a higher temperature favored the growth of moderate thermophiles. Even though microbial abundance and activity were highest at 30°C, the column at a higher temperature achieved a much higher Cu leaching efficiency and recovery, which suggested that the promotion of chemical oxidation by elevated temperature dominated the dissolution of Cu. The highest pyrite oxidation percentage was detected at 45°C. Higher temperature resulted in precipitation of jarosite in columns, especially at 60°C. The results gave implications to the optimization of heap bioleaching of secondary copper sulfide in both enhanced chalcocite leaching and acid/iron balance, from the perspective of leaching temperature and affected microbial community and activity.

Rock-magnetism and ore microscopy of the magnetite-apatite ore deposit from Cerro de Mercado, Mexico

Science.gov (United States)

Alva-Valdivia, L. M.; Goguitchaichvili, A.; Urrutia-Fucugauchi, J.; Caballero-Miranda, C.; Vivallo, W.

2001-03-01

Rock-magnetic and microscopic studies of the iron ores and associated igneous rocks in the Cerro de Mercado, Mexico, were carried out to determine the magnetic mineralogy and origin of natural remanent magnetization (NRM), related to the thermo-chemical processes due to hydrothermalism. Chemical remanent magnetization (CRM) seems to be present in most of investigated ore and wall rock samples, replacing completely or partially an original thermoremanent magnetization (TRM). Magnetite (or Ti-poor titanomagnetite) and hematite are commonly found in the ores. Although hematite may carry a stable CRM, no secondary components are detected above 580°, which probably attests that oxidation occurred soon enough after the extrusion and cooling of the ore-bearing magma. NRM polarities for most of the studied units are reverse. There is some scatter in the cleaned remanence directions of the ores, which may result from physical movement of the ores during faulting or mining, or from perturbation of the ambient field during remanence acquisition by inhomogeneous internal fields within these strongly magnetic ore deposits. The microscopy study under reflected light shows that the magnetic carriers are mainly titanomagnetite, with significant amounts of ilmenite-hematite minerals, and goethite-limonite resulting from alteration processes. Magmatic titanomagnetites, which are found in igneous rocks, show trellis, sandwich, and composite textures, which are compatible with high temperature (deuteric) oxy-exsolution processes. Hydrothermal alteration in ore deposits is mainly indicated by martitization in oxide minerals. Grain sizes range from a few microns to >100 mm, and possible magnetic state from single to multidomain, in agreement with hysteresis measurements. Thermal spectra, continuous susceptibility measurements, and IRM (isothermal remanent magnetization) acquisition suggest a predominance of spinels as magnetic carriers, most probably titanomagnetites with low

Uranium production from low grade Swedish shale

International Nuclear Information System (INIS)

Carlsson, O.

1977-01-01

In view of the present nuclear programmes a steep increase in uranium demand is foreseen which will pose serious problems for the uranium industry. The annual additions to uranium ore reserves must almost triple within the next 15 years in order to support the required production rates. Although there are good prospects for the discovery of further conventional deposits of uranium there is a growing interest in low grade uranium deposits. Large quantities of uranium exist in black shales, phosphates, granites, sea water and other unconventional sources. There are however factors which limit the utilization of these low grade materials. These factors include the extraction costs, the environmental constrains on mining and milling of huge amounts of ore, the development of technologies for the beneficiation of uranium and, in the case of very low grade materials, the energy balance. The availability of by-product uranium is limited by the production rate of the main product. The limitations differ very much according to types of ores, mining and milling methods and the surroundings. As an illustration a description is given of the Swedish Ranstad uranium shale project, its potential, constraints and technical solutions

Secondary resources processing in production of nuclear grade yellow cake

International Nuclear Information System (INIS)

Sivasubramanian, S.

2009-01-01

Full text: Recovering uranium in a cost competitive manner from sources other than the uranium ore is considered necessary from the point of view of meeting the strategic as well as the nuclear power programme need of the country. Globally, uranium is produced from ores which have more than 10 times uranium content compared to those available in India. Secondary sources of uranium are mostly defined by recycled uranium, from spent fuel of nuclear reactors, re-enriched depleted uranium tails, ex-military weapons grade uranium and stock piles for civilian use. Uranium production from secondary sources in India is largely dependent on processing of monazite, and to a smaller extent it is recovered from waste metallurgical slags generated by BARC and other private industries engaged in extracting niobium tantalum from the ores. The paper gives over view of the commercially successful processes of producing uranium from monazite and other secondary sources along with the details of setting up demonstration units for recovering uranium from wet phosphoric acid. The research and development work carried out to improve the cost economics of uranium production from monazite is also discussed as the total reported quantity of uranium associated with the monazite resources of the country is estimated at 30,000 tons of uranium metal (at the end of X Plan) compared to 75,000 ton of uranium in its primary ores

Radioisotope devices at Novo-Krivorozhskij-ore-enrichment plant

International Nuclear Information System (INIS)

Levitskij, V.Ya.; Kucher, V.G.; Ministerstvo Chernoj Metallurgii Ukrainskoj SSR, Dnepropetrovsk, Bazovaya Opytno-Konstruktorskaya Izotopnaya lab.)

1975-01-01

Use of the ''Ferrite'' analyzers, AZhR and PAZh-1 and the GR-7 gamma relay in different engineering areas of the Novo-Krivorozh ore-enrichment plant is evaluated. The ''Ferrite'' radioisotopic analyzer was designed for rapid roentgeno-radiometric determination of the total iron and iron group element contents in powdered samples of ores and products of their treatment. From the density of the flux of the characteristic radiation it is possible to determine quantitatively the content of the element of interest in the analyzed material. The radioisotpic analyzer AZhR-1 is distinguished by its high efficiency in the analysis for total iron on products of processing of iron ore raw materials. The use of this apparatus allows complete replacement of the chemical method for rapid analysis of concentrates by the roentgeno-radiometric method, which decreases the total analytical work on determination of total iron and speeds up output of information on concentrate quality. The radioisotopic gamma analyzer PAZh-1 is designed for automatic and either continuous or discrete measurement of the total iron content in iron ore materials ground to 50 mm, carried on a conveyor, without selection or preparation of the samples for analysis. The analyzer operates on the principle of measuring the average frequency of impingement on a detector of gamma quanta back-scattered by the analyzed material. This frequency is determined by the percentage content of total iron in the material. The apparatus operates continuously. The mean square deviation of the apparatus values from chemical data is 0.93% Fesub(total). Use of the apparatus greatly increases the operativeness of the control and decreases the laboriousness of raw material sampling in an engineering stream. The radioisotopic data units GR-7 are designed for control of the level of materials in hoppers for recovery and burning of agglomerates. Use of this apparatus showed its great advantage over data units of other types

The critical importance of pulp concentration on the flotation of galena from a low grade lead–zinc ore

Directory of Open Access Journals (Sweden)

Xianping Luo

2016-04-01

Full Text Available The Qixia orebody is a complex lead–zinc sulfide system with pyrite gangue and minor amounts of copper. In order to improve the flotation results, laboratory scale flotation testing of ore samples taken from this operation was performed. Flotation tests used a sequential recovery protocol for selective flotation of first the lead and thereafter the zinc. The key parameters that influence flotation performance of lead mineral were tested in this paper. The test data show that, for comparable collector, grinding time, flotation pH and solid-in-pulp concentration, the increase of solid-in-pulp concentration has the most significant effect on the recovery and selective separation of lead mineral. The increase of solid-in-pulp concentration from 27% to 55% makes the recovery of lead mineral increased from 60% to 80% and the lead grade increased from 27.5% to 29.1%.

Surface modification and column flotation of a massive ilmenite ore

International Nuclear Information System (INIS)

Fan, X.; Rowson, N.A.

2002-01-01

The main problems with ilmenite flotation in impeller-type flotation machines are the poor flotation behaviour of ilmenite and the negative effect of slimes. These cause high ilmenite losses in tailings even when a large dosage of fatty acid and fuel oil is consumed. In this study, microwave radiation pre-treatment and ilmenite surface activation were used to modify the surface properties of a massive ilmenite ore sample from Norway to improve ilmenite flotability. A column cell was used to minimize the negative effect of slimes on ilmenite separation efficiency. When ilmenite flotation was performed in a 1 litre Denver cell, the flotation recovery of titanium dioxide from the ilmenite ore sample was only 68.5% (31.1% TiO 2 ) under conventional flotation conditions. After microwave radiation pre-treatment for three minutes at 2600 W and 2.45 GHz, the ferrous ions on ilmenite particle surfaces were converted into ferric ions; hence, the recovery increased from 68.5% to 86.8%. The concentrate grade increased from 31.1% TiO 2 to 32.1% TiO 2 . In ilmenite activation flotation, Pb 2+ ions can be selectively adsorbed on to ilmenite particle surfaces as active sites and therefore enhance the adsorption of oleate ions on ilmenite surfaces. With the addition of 60 g/ton Pb(NO 3 ) 2 , ilmenite flotation recovery increased from 68.5% to 85.1%. However, the quality of ilmenite concentrates was not improved due to the negative effect of slimes. After a two stage cleaning, the grade of ilmenite concentrates was only about 31% TiO 2 . The combination of microwave radiation pre-treatment and the application of a column cell overcame both problems of poor flotability and the negative effect of slimes. When the Denver cell was replaced by a column cell and the massive ilmenite ore sample was pre-treated using microwave radiation for three minutes, the ilmenite concentrate grade increased from 31.1% TiO 2 to 42.9% TiO 2 and the titanium dioxide recovery increased from 68.5% to 90

Technological pretreatment of the synchysite non-oxidized ore

Science.gov (United States)

Munkhtsetseg, B.; Burmaa, G.

2013-06-01

Mongolia has rich deposits of rare, precious, and poly-metallic ores. Nowadays, it is important to research separation of rare earth elements oxides concentrates from the ores, analyze their unique physical chemical characteristics, and purified it. Our investigation on raw materials focuses on rare earth non-oxidized ores. Main mineral in this rock sample is Synchysite (LnCa(CO3)2F. We did technological and thermal pretreatment: direct sulphurization (H2SO4), sulphurization with subsequent roasting (800°C+H2SO4), sulphurization prior to roasting (H2SO4+650°C). Sulphurization method based on dissolution of rare earth mineral into sulfuric acid (93%) according to the reaction. The amount of rare earth element oxides is almost 10 times greater (29.16%) after direct sulphurization process, almost 8 times greater (21.14%) after sulphurization with subsequent roasting, and almost 20 times greater (44.62%) after sulphurization prior to roasting process. After those technological pretreatment raw material's micro elements Thorium and Uranium contents are reduced as follows: H2SO4>800°C+H2SO4>H2SO4+650°C. These results show that cerium group rare earth elements have very good solubility in water at +2°C temperature and decreasing micro elements content uranium and thorium good pretreatment condition is prior to roasting (H2SO4+650°C) of synchysite non-oxidized ore.

Composition and origin of Early Cambrian Tiantaishan phosphorite-Mn carbonate ores, Shaanxi Province, China

Science.gov (United States)

Hein, J.R.; Fan, D.; Ye, J.; Liu, T.; Yeh, H.-W.

1999-01-01

The Tiantaishan phosphorite-Mn carbonate ores occur in the Early Cambrian Tananpo Formation in complexly folded and faulted rocks located in southern Shaanxi Province. About 65 x 106 tonnes of 17% P2O5 ore reserves exist and Mn-ore reserves are about 8.3 x 106 tonnes of +18% Mn. The stratigraphic sequence in ascending order consists of black phyllite, black to gray phosphorite ore, black phyllite, rhodochrostone ore, Mn mixed-carbonates, and dolostone. Data are presented from microprobe mineral chemistry, whole-rock chemistry, stable isotopes of carbonates, X-ray mineralogy, petrographic and SEM observations, and statistical analysis of chemical data. The dominant ore-forming minerals are hydroxy- and carbonate fluorapatite and Ca rhodochrosite, with Mg kutnahorite and dolomite comprising the Mn mixed-carbonate section. Pyrite occurs in all rock types and alabandite (MnS) occurs throughout the rhodochrostone section. The mean P2O5 content of phosphorite is 31% and argillaceous phosphorite is 16%, while the mean MnO content of rhodochrostone ore is 37%. Phosphorite ores are massive, spheroidal, laminated, and banded, while rhodochrostone ores have oolitic, spheroidal, and granular fabrics. The most distinguishing characteristics of the ores are high total organic carbon (TOC) contents (mean 8.4%) in the phosphorite and high P2O5 contents (mean 2.7%) in the rhodochrostone ore. The atypically high TOC contents in the Tiantaishan phosphorite probably result from very strong productivity leading to high sedimentation rates accompanied by weak reworking of sediments; poor utilization of the organic matter by bacteria; and/or partial replacement of bacterial or algal mats by the apatite. The depositional setting of the ores was the margin of an epicontinental seaway created as a direct consequence of global processes that included break-up of a supercontinent, formation of narrow seaways, creation of extensive continental shelves, overturn of stagnant, metal-rich deep

The recovery of a concentrate of tin and tungsten from ore mined at Van Roois Vley

International Nuclear Information System (INIS)

Guest, R.N.

1985-01-01

Concentration tests using gravity separation, flotation, and magnetic separation showed that it is possible for the high-grade ore mined at Van Roois Vley to be upgraded to a concentrate containing 61 per cent Sn-Wo 3 at a recovery of about 80 per cent, and for the low-grade ore to be upgraded to 53 per cent Sn-WO 3 at the same recovery. However, it is suggested that, under normal mining conditions and with large-scale mining equipment, less fines would be produced and this should lead to an increase in grade and recovery. Mineralogical examinations showed that intermediate fractions produced by tabling contained very few locked particles, and that the grade of the final concentrate on a full-scale plant would probably be higher than that obtained with laboratory equipment. Molybdenite could be a valuable byproduct, but flotation tests of gravity concentrates for selective recovery of the mineral gave variable results. Flotation tests for the removal of fluorspar from the final concentrate were unsuccessful

Mineralogical test as a preliminary step for metallurgical proses of Kalan ores

International Nuclear Information System (INIS)

Affandi, K.

1998-01-01

Mineralogical tests as a preliminary step for hydrometallurgy of Kalan ores, including Eko Remaja and Rirang have been carried out to identify the elements and minerals content which affect the metallurgical process, especially the leaching and purification of uranium. Mineralogical tests have been done by means of radioactive and radioluxugraph tests to identify radioactive minerals; thin specimen analysis, Scanning Electron Microscopy (SEM) to identify elements and morphology, EPMA to analyse qualitatively the elements, X-ray Diffractometer (XRD) to identify of minerals content; and X-ray Fluorescence (XRF) and chemical analyses to determine total elements qualitatively and quantitatively. The experimental results show that the Eko Remaja ores contain uraninite and brannerite, iron and titan oxides, sulfides, phosphates and silicates minerals, while the Rirang ores contain uraninite, monazite and molybdenite

Concentration of rare earths ore from Pocos de Caldas - MG, Brazil

International Nuclear Information System (INIS)

Sampaio, J.A.; Lins, F.F.; Porphirio, N.H.

1990-01-01

The objective of this research was to concentrate, mainly by flotation, a rare-earth ore body. The valuable mineral is bastnaesite which occurs intimately associated with iron oxides and other gangue minerals, making difficult to get a concentrate of commercial grade. The use of oleic acid at a pulp temperature of -80 sup(0)C gave a concentrate of 23% rare-earth oxides at 72% overall recovery. The magnetic separation could enhance the grade of the flotation feed. (author)

Geodynamic condition of formation of favorable structural positions for ore-grade gold placement in auminzatau-beltau ore area (the central kyzyl kum, western uzbekistan)

Science.gov (United States)

Janibekov, Bobir Omonovich; Turapov, M. K.

2017-09-01

Work is directed on studying of a geodynamic condition under which the structural positions controlling process of endogenous ore formation were formed. It is shown that explosive region tectonics under the influence of regional tectonic efforts formed structural elements (positions) which controlled formation of gold deposits. It is recognized that structural positions are defined by variety of systems of disjunctive dislocation and their relationship among themselves. Formation of favorable positions depends as well on morphology of ore controlling structures, on degree of their tectonic activity and spatial situation in relation to the direction of tectonic (geodynamic) efforts.

Technology of Polish copper ore beneficiation – perspectives from the past experience

Directory of Open Access Journals (Sweden)

Wieniewski Andrzej

2016-01-01

Full Text Available The paper describes the main types of existing copper deposits in the world and the most common enrichment technologies. The characteristic elements of the current flowsheet of the Polish ore beneficiation were discussed together with the reasons for using them. The paper presents a perspective flowsheet based on more than 50-years of experience in beneficiation of Polish copper ore. The main elements of proposed technology are: leaving in justified cases the division of ore into fractions of increased sandstone and carbonate ores content, flotation in the milling circuit as part of the effective preparation of the ore to rougher flotation, intensive rougher flotation, classic cleaning system, processing of the middlings with grinding system in new type mills, classification and flotation with outlet of final tailings.

Hemimorphite Ores: A Review of Processing Technologies for Zinc Extraction

Science.gov (United States)

Chen, Ailiang; Li, Mengchun; Qian, Zhen; Ma, Yutian; Che, Jianyong; Ma, Yalin

2016-10-01

With the gradual depletion of zinc sulfide ores, exploration of zinc oxide ores is becoming more and more important. Hemimorphite is a major zinc oxide ore, attracting much attention in the field of zinc metallurgy although it is not the major zinc mineral. This paper presents a critical review of the treatment for extraction of zinc with emphasis on flotation, pyrometallurgical and hydrometallurgical methods based on the properties of hemimorphite. The three-dimensional framework structure of hemimorphite with complex linkage of its structural units lead to difficult desilicification before extracting zinc in the many metallurgical technologies. It is found that the flotation method is generally effective in enriching zinc minerals from hemimorphite ores into a high-grade concentrate for recovery of zinc. Pure zinc can be produced from hemimorphite or/and willemite with a reducing reagent, like methane or carbon. Leaching reagents, such as acid and alkali, can break the complex structure of hemimorphite to release zinc in the leached solution without generation of silica gel in the hydrometallurgical process. For optimal zinc extraction, combing flotation with pyrometallurgical or hydrometallurgical methods may be required.

The use of radiometric ore sorting on South African gold mines

International Nuclear Information System (INIS)

Boehme, R.C.; Freer, J.S.

1982-01-01

This paper refers to the radiometric sorting tests reported during the 7th CMMI Congress, and then describes the photometric and radiometric sorter installations in operation and under construction in South Africa at present. As radiometric sorting of gold ores uses the radiation from the uranium content as a tracer, it is essential that the sortability of the ore should be reliably determined before sorting is adopted. The method of obtaining the important ore characteristics is described, with examples. The possible increase in gold production from a hypothetical plant as a result of sorting is shown

Experimental design and optimization of leaching process for recovery of valuable chemical elements (U, La, V, Mo, Yb and Th) from low-grade uranium ore.

Science.gov (United States)

Zakrzewska-Koltuniewicz, Grażyna; Herdzik-Koniecko, Irena; Cojocaru, Corneliu; Chajduk, Ewelina

2014-06-30

The paper deals with experimental design and optimization of leaching process of uranium and associated metals from low-grade, Polish ores. The chemical elements of interest for extraction from the ore were U, La, V, Mo, Yb and Th. Sulphuric acid has been used as leaching reagent. Based on the design of experiments the second-order regression models have been constructed to approximate the leaching efficiency of elements. The graphical illustrations using 3-D surface plots have been employed in order to identify the main, quadratic and interaction effects of the factors. The multi-objective optimization method based on desirability approach has been applied in this study. The optimum condition have been determined as P=5 bar, T=120 °C and t=90 min. Under these optimal conditions, the overall extraction performance is 81.43% (for U), 64.24% (for La), 98.38% (for V), 43.69% (for Yb) and 76.89% (for Mo) and 97.00% (for Th). Copyright © 2014 Elsevier B.V. All rights reserved.

Upgrading of boron ores and colemanite flotation

International Nuclear Information System (INIS)

Yarar, B.; Mager, J.

1979-01-01

Processes applied for the processing and upgrading of sodium and calcium borates in Turkey are described. Details of froth flotation study where a low grade colemanite ore containing calcite and clays as a gangue minerals are given. It has been found that, at the natural pH of a colemanite-containing pulp (pH=9,2) it is possible to float colemanite selectively using dodecyl benzene sulphonate or its combinations with a non-polar reagent or naphthenic acids. (author)

Midwest Joint Venture high-grade uranium mining

International Nuclear Information System (INIS)

Fredrickson, H.K.

1992-01-01

Midwest Joint Venture (MJV) owns a high-grade uranium deposit in northern Saskatchewan. The deposit is located too deep below surface to be mined economically by open pit methods, and as a consequence, present plans are that it will be mined by underground methods. High-grade uranium ore of the type at MJV, encased in weak, highly altered ground and with radon-rich water inflows, has not before been mined by underground methods. The test mining phase of the project, completed in 1989, had three objectives: To evaluate radiation protection requirements associated with the handling of large quantities of radon-rich water and mining high-grade uranium ore in an underground environment; to investigate the quantity and quality of water inflows into the mine; and, to investigate ground conditions in and around the ore zone as an aid in determining the production mining method to be used. With information gained from the test mining project, a mining method for the production mine has been devised. Level plans have been drawn up, ventilation system designed, pumping arrangements made and methods of ore handling considered. All this is to be done in a manner that will be safe for those doing the work underground. Some of the mining methods planned are felt to be unique in that they are designed to cope with mining problems not known to have been encountered before. New problems underground have required new methods to handle them. Remote drilling, blasting, mucking and backfilling form the basis of the planned mining method

Spectrophotometric Determination of Thorium in Low Grade Minerals and Ores

Energy Technology Data Exchange (ETDEWEB)

Arnfelt, A L; Edmundsson, I

1960-08-15

The following method is intended for the determination of microgram quantities of thorium in samples of minerals and ores. The mineral sample is decomposed by repeated sintering with sodium peroxide. After digestion with water thorium peroxide hydrate is recovered by centrifugation and dissolved in hydrochloric acid. Thorium is determined spectrophotometrically with naphtarson after its separation from metals forming chloro complexes which are adsorbed on a strongly basic anion exchange resin. Interferences from a few different ions have been studied. The time required for the analysis of one sample is about 4 hours, when analysing 12 samples simultaneously

Spectrophotometric Determination of Thorium in Low Grade Minerals and Ores

International Nuclear Information System (INIS)

Arnfelt, A.L.; Edmundsson, I.

1960-08-01

The following method is intended for the determination of microgram quantities of thorium in samples of minerals and ores. The mineral sample is decomposed by repeated sintering with sodium peroxide. After digestion with water thorium peroxide hydrate is recovered by centrifugation and dissolved in hydrochloric acid. Thorium is determined spectrophotometrically with naphtarson after its separation from metals forming chloro complexes which are adsorbed on a strongly basic anion exchange resin. Interferences from a few different ions have been studied. The time required for the analysis of one sample is about 4 hours, when analysing 12 samples simultaneously

Optimization of operating parameters and rate of uranium bioleaching from a low-grade ore

International Nuclear Information System (INIS)

Rashidi, A.; Roosta-Azad, R.; Safdari, S.J.

2014-01-01

In this study the bioleaching of a low-grade uranium ore containing 480 ppm uranium has been reported. The studies involved extraction of uranium using Acidithiobacillus ferrooxidans derived from the uranium mine samples. The maximum specific growth rate (μ max ) and doubling time (t d ) were obtained 0.08 h -1 and 8.66 h, respectively. Parameters such as Fe 2+ concentration, particle size, temperature and pH were optimized. The effect of pulp density (PD) was also studied. Maximum uranium bio-dissolution of 100 ± 5 % was achieved under the conditions of pH 2.0, 5 % PD and 35 deg C in 48 h with the particles of d 80 = 100 μm. The optimum concentration of supplementary Fe 2+ was dependent to the PD. This value was 0 and 10 g of FeSO 4 ·7H 2 O/l at the PD of 5 and 15 %, respectively. The effects of time, pH and PD on the bioleaching process were studied using central composite design. New rate equation was improved for the uranium leaching rate. The rate of leaching is controlled with the concentrations of ferric and ferrous ions in solution. This study shows that uranium bioleaching may be an important process for the Saghand U mine at Yazd (Iran). (author)

Potential for cobalt recovery from lateritic ores in Europe

Science.gov (United States)

Herrington, R.

2012-04-01

Cobalt is one of the 'critical metals' identified under the EU Raw Materials Initiative. Annually the global mine production of cobalt is around 55,000 tonnes,with Europe's industries consuming around 30% of that figure. Currently Europe produces around 27 tonnes of cobalt from mines in Finland although new capacity is planned. Co-bearing nickel laterite ores being mined in Greece, Macedonia and Kosovo where the cobalt is currently not being recovered (ores have typical analyses of 0.055% Co and >1% Ni,). These ores are currently treated directly in pyrometallurgical plants to recover the contained nickel and this process means there is no separate cobalt product produced. Hydrometallurgical treatment of mineralogically suitable laterite ores can recover the cobalt; for example Cuba recovers 3,500 tonnes of cobalt from its laterite mining operations, which are of a similar scale to the current European operations. Implementation of hydrometallurgical techniques is in its infancy in Europe with one deposit in Turkey planning to use atmospheric heap leaching to recover nickel and copper from oxide-dominated ores. More widespread implementation of these methods to mineralogically suitable ore types could unlock the highly significant undeveloped resources (with metal contents >0.04% Co and >1% Ni), which have been defined throughout the Balkans eastwards into Turkey. At a conservative estimate, this region has the potential to supply up to 30% of the EU cobalt requirements.

Uranium ores

International Nuclear Information System (INIS)

Poty, B.; Roux, J.

1998-01-01

The processing of uranium ores for uranium extraction and concentration is not much different than the processing of other metallic ores. However, thanks to its radioactive property, the prospecting of uranium ores can be performed using geophysical methods. Surface and sub-surface detection methods are a combination of radioactive measurement methods (radium, radon etc..) and classical mining and petroleum prospecting methods. Worldwide uranium prospecting has been more or less active during the last 50 years, but the rise of raw material and energy prices between 1970 and 1980 has incited several countries to develop their nuclear industry in order to diversify their resources and improve their energy independence. The result is a considerable increase of nuclear fuels demand between 1980 and 1990. This paper describes successively: the uranium prospecting methods (direct, indirect and methodology), the uranium deposits (economical definition, uranium ores, and deposits), the exploitation of uranium ores (use of radioactivity, radioprotection, effluents), the worldwide uranium resources (definition of the different categories and present day state of worldwide resources). (J.S.)

Growth characteristics of a strain of iron-oxidizing bacterium and its application in bioleaching of uranium ores

International Nuclear Information System (INIS)

Zhang Rui; Liu Yajie; Gao Feng; Xu Lingling

2008-01-01

05B is a strain of iron-oxidizing bacterium which separated from a uranium ore. The effect of temperature, initial pH, inoculation amount and initial total iron concentration on the strain's growth and activities in bioleaching of uranium ores are studied. The results show that the optimum growth temperature is 40-45 degree C, the optimum inoculation pH value being 1.5-1.7, the optimum initial inoculation amount being 10%-20%, and the initial total iron concentration being not more than 5 g/L. 05B is fit for leaching of low grade uranium ores. (authors)

Research on metallogenic conditions of intersection-type uranium ore-deposits in Zhongdong area, Northern Guangdong province

International Nuclear Information System (INIS)

Wang Zhengqi; Wu Lieqin; Zhang Guoyu

2007-12-01

The methods following as field geological investigation, trace element geo- chemistry and isotope geochemistry were used in this project. Based on geological and geochemical characteristics of Xiaoshui uranium ore deposits in Zhongdong area, Xiazhuang ore-field, Guangdong province, it could be concluded that: (1) The Provenance of Cretaceous mantle is a enriched mantle; (2) Silicified zone-type and intersection-type uranium ore are distinctness in the metallogenic period and mineralization process, and main metallogenic period of Xiaoshui uranium ore-deposit is 73.5 Ma; (3) The sources of uranium mineralization substance derived from enriched mantle; and (4)The intersection-type high grade uranium deposits were controlled by substances derived from mantle (contain with U, CO 2 , F, et al), tracks of intersection of NWW-across with NNE-trending faults and lithology of diabase. (authors)

Research on metallogenic conditions of intersection-type uranium ore-deposits in Zhongdong area, Northern Guangdong province

Energy Technology Data Exchange (ETDEWEB)

Zhengqi, Wang [East China Inst. of Technology, Fuzhou (China); [Beijing Research Inst. of Uranium Geology, Beijing (China); Lieqin, Wu [Institute No.290, CNNC, Shaoguan (China); Guoyu, Zhang [East China Inst. of Technology, Fuzhou (China)

2007-12-15

The methods following as field geological investigation, trace element geo- chemistry and isotope geochemistry were used in this project. Based on geological and geochemical characteristics of Xiaoshui uranium ore deposits in Zhongdong area, Xiazhuang ore-field, Guangdong province, it could be concluded that: (1) The Provenance of Cretaceous mantle is a enriched mantle; (2) Silicified zone-type and intersection-type uranium ore are distinctness in the metallogenic period and mineralization process, and main metallogenic period of Xiaoshui uranium ore-deposit is 73.5 Ma; (3) The sources of uranium mineralization substance derived from enriched mantle; and (4)The intersection-type high grade uranium deposits were controlled by substances derived from mantle (contain with U, CO{sub 2}, F, et al), tracks of intersection of NWW-across with NNE-trending faults and lithology of diabase. (authors)

Spectrometric gamma investigations concerning zinc-lead ores and the products of their processing

International Nuclear Information System (INIS)

Girczys, J.; Skowronek, J.; Zrodlowski, B.

1983-01-01

Zinc-lead ore and products of its enrichment were investigated using gamma spectrometry for the content of uranium, thorium and potassium 40. It was stated that the mean content of these elements in a deposit does not diverge from their mean concentration in the lithosphere. They also accompany the surrounding rocks. As a result of mechanical processing of this ore radionuclides pass discards in which they do not form concentrations dangerous for life, either. In the exploitation areas and in the surroundings there is no state of ecological hazard. (author)

Genesis of iron-apatite ores in Posht-e-Badam Block (Central Iran) using REE geochemistry

Science.gov (United States)

Mokhtari, Mir Ali Asghar; Zadeh, Ghader Hossein; Emami, Mohamad Hashem

2013-06-01

Rare earth elements in apatites of different ore types show characteristic patterns which are related to different modes of formation of the ores. Most of the apatite-bearing iron ores are associated with alkaline magmas with LREE/HREE fractionation varying from moderate to steep. Iron-apatite deposits in Posht-e-Badam Block (Central Iran) have a high concentration of REE (more than 1000 ppm up to 2.5%), and show a strong LREE/HREE ratio with a pronounced negative Eu anomaly. This REE pattern is typical of magmatic apatite and quiet distinct from sedimentary apatites (phosphorites) which have a low REE contents and Ce negative anomalies. On the other hand, they are comparable to the REE patterns of apatites in Kiruna-type iron ores in different parts of the world. The REE patterns of apatites, iron-apatite ores and iron ores are similar and only have different REE contents. This similarity indicates a genetic relation for these rocks. Most of the iron-apatite deposits in Central Iran have similar REE patterns too, which in turn show a genetic relation for all of these deposits. This similarity indicates a similar origin and processes in their genesis. There are some small intrusions around some of the iron-apatite deposits that are petrographically identified as syenite and gabbro. These intrusions also have REE patterns similar to that of iron-apatite ores. This demonstrates a genetic relation between these intrusions and iron-apatite ores. The REE patterns of apatites in different deposits of Posht-e-Badam Block iron-apatite ores show an affinity to alkaline to sub-alkaline magmas and rifting environment. The alkaline host rocks of Central Iran iron-apatite ores are clearly related to an extensional setting where rifting was important (SSE-NNW fault lines). A probable source for this large scale ore forming processes is relatively low partial melting of mantle rocks. The ores have originated by magmatic differentiation as a late phase in the volcanic cycle

Porphyry-Copper Ore Shells Form at Stable Pressure-Temperature Fronts Within Dynamic Fluid Plumes

Science.gov (United States)

Weis, P.; Driesner, T.; Heinrich, C. A.

2012-12-01

Porphyry-type ore deposits are major resources of copper and gold, precipitated from fluids expelled by crustal magma chambers. The metals are typically concentrated in confined ore shells within vertically extensive vein networks, formed through hydraulic fracturing of rock by ascending fluids. Numerical modeling shows that dynamic permeability responses to magmatic fluid expulsion can stabilize a front of metal precipitation at the boundary between lithostatically pressured up-flow of hot magmatic fluids and hydrostatically pressured convection of cooler meteoric fluids. The balance between focused heat advection and lateral cooling controls the most important economic characteristics, including size, shape, and ore grade. This self-sustaining process may extend to epithermal gold deposits, venting at active volcanoes, and regions with the potential for geothermal energy production.

Radioanalysis of RE enrichment of ion adsorption type RE ores

CERN Document Server

Zhao Shu Quan; Hu He Ping; Li Fu Sheng; Chen Ying Min; LiuShiMing

2002-01-01

Objective: To analyze the radioactivity in Rare Earth (RE) enrichment of ion adsorption type RE ores. Methods: Using HPGe-gamma spectrometer to analyze the activity ratio of gamma radionuclides in kind of samples, using FJ-2603 low background alpha, beta measurement apparatus to measure their total alpha and total beta activities, and using X-ray fluorescence spectrometer to analyze contents of La sub 2 O sub 3 and Y sub 2 O sub 3 , respectively. Results: HPGe gamma spectroscopy and X-ray fluorescence spectroscopy are simple, convenient and non-destructive methods of analyzing radionuclides and La sub 2 O sub 3 , Y sub 2 O sub 3 in RE enrichment of ion adsorption type RE ores, respectively. Conclusion: The basic data were provided for radiation protection and treatment of gas, liquid and solid waste in RE production of ion adsorption type RE ores; method and experience were provided for studying ion adsorption type RE ores

Hydrogeochemical radioactive features and prospecting in granopegmatite type uranium ore district in Danfeng area

International Nuclear Information System (INIS)

Feng Zhangsheng

2011-01-01

Hydrochemical radioactive prospecting plays an important role in the all stages of grano-pegmatite type uranium deposit exploration in Danfeng area dut to its fast, simple, economic and high effective advantage. Radioactive anomalous halo in the shallow underground water has identical distribution scopes with the ore-bearing biotite granite-pegmatite, which can be used to delineate uranium ore-forming prospective area, reconnaissance area and detailed prospecting area. Deep underground water close to the ore is characterized by hydrogeochemical radioactive features with high uranium and radon content. Through prospecting engineering of radioactive hydrogeochemical, the situation of blind ore bodies can be used to guide the layout. (authors)

Correlation of DNA content and nucleomorphometric features with World Health Organization grading of meningiomas.

Science.gov (United States)

Grunewald, J P; Röhl, F W; Kirches, E; Dietzmann, K

1998-02-01

Many studies dealing with extracranial cancer showed a strong correlation of DNA ploidy to a poor clinical outcome, recurrence, or malignancy. In brain tumors, analysis of DNA content did not always provided significant diagnostic information. In this study, DNA density and karyometric parameters of 50 meningiomas (26 Grade I, 10 Grade II, 14 Grade III) were quantitatively evaluated by digital cell image analyses of Feulgen-stained nuclei. In particular, the densitometric parameter SEXT, which describes nuclear DNA content, as well as the morphometric values LENG (a computer-assisted measurement of nuclear circumference), AREA (a computer-assisted measurement of nuclear area), FCON (a parameter that describes nuclear roundness), and CONC (a describing nuclear contour), evaluated with the software IMAGE C, were correlated to World Health Organization (WHO) grading using univariate and multivariate methods. AREA and LENG values showed significant differences between tumors of Grades I and III. FCON values were unable to distinguish WHO Grade III from Grade I/II but were useful in clearly separating Grade II from Grade I tumors. CONC values detected differences between WHO Grades II and I/III tumors but not between the latter. SEXT values clearly distinguished Grade III from Grade I/II tumors. The 1c, 2c, 2.5c, and 5c exceeding rates showed no predictive values. Only the 6c exceeding rate showed a significant difference between Grades I and III. These results outline the characteristic features of the atypical (Grade II) meningiomas, which make them a recognizable tumor entity distinct from benign and anaplastic meningiomas. The combination of DNA densitometric and morphometric findings seems to be a powerful addition to the histopathologic classification of meningiomas, as suggested by the WHO.

Study on the determination of ore-formation age of primary gold ore

International Nuclear Information System (INIS)

Ying Junlong; Zhao Puyun; Guo Hong

1997-01-01

The accurate determination of gold ore-formation age and ore-source isotope composition are of important significance in the research on gold geology and prospecting. According to the summary of three year indoor and field work, the ore-formation ages and isotope compositions of some typical gold deposits were obtained: The age of gold ore of the Wuhuaaobao deposit in geo-syncline region north to the north margin of North-China paleo-land is 130-120 Ma corresponding to the Late-orogenic stage. The ore-formation age of the Saiwusu gold deposit in the southern platform region is 211 +- 15 Ma, recycling reworking of the old-land. The Hougou-Huangtuliang gold deposit located in the middle of the platform region is 243 +- 7 Ma old attributed to the regeneration ore-formation on the old-land. the age of Jiaojia-Rushan gold deposit in Eastern Shandong is 122.7 +- 3.4 Ma and 128 +- 23 Ma belonging to Yanshanian stage. The Babaoshan gold-silver deposit in Cathaysian old-land is 140 +- 5 Ma old originated from volcanic hydrothermal ore-formation

Installation of Radiometric Sorting throughout the Cogema-Simo Mining Complex at Lodeve. [Uranium ores

Energy Technology Data Exchange (ETDEWEB)

Grenier, J.; Winter, J.M.; Deville, P.

1986-06-01

The ores of Lodeve present no physical characteristics which permit an elimination of the lowest grade fractions, with the exception of the radioactivity and the radium which accompanies the uranium. The mine therefore turned to radiometric pebble-by-pebble sorting on a machine model M 17 of Ore Sorters who have a monopoly of this type of equipment; this permits an operation over a size range from 25 to 160 mm. Sampling of the deposit investigation of pebble samples, construction of the sorting plant and commissioning are described.

Uranium and thorium recovery in thorianite ore-preliminary results

Energy Technology Data Exchange (ETDEWEB)

Gaiotte, Joao V.M. [Universidade Federal de Alfenas, Pocos de Caldas, MG (Brazil); Villegas, Raul A.S.; Fukuma, Henrique T., E-mail: rvillegas@cnen.gov.br, E-mail: htfukuma@cnen.gov.br [Comissao Nacional de Energia Nuclear (CNEN), Pocos de Caldas, MG (Brazil). Lab. de Pocos de Caldas

2011-07-01

This work presents the preliminary results of the studies aiming to develop a hydrometallurgical process to produce uranium and thorium concentrates from thorianite ore from Amapa State, Brazil. This process comprises two major parts: acid leaching and Th/U recovery using solvent extraction strategies. Thorianite ore has a typical composition of 60 - 70% of thorium, 8 - 10% lead and 7 - 10% uranium. Sulfuric acid leaching operational conditions were defined as follows: acid/ore ratio 7.5 t/t, ore size below 65 mesh (Tyler), 2 hours leaching time and temperature of 100 deg C. Leaching tests results showed that uranium and thorium recovery exceeded 95%, whereas 97% of lead ore content remained in the solid form. Uranium and thorium simultaneous solvent extraction is necessary due to high sulfate concentration in the liquor obtained from leaching, so the Primene JM-T primary anime was used for this extraction step. Aqueous raffinate from extraction containing sulfuric acid was recycled to the leaching step, reducing acid uptake around 60%, to achieve a net sulfuric acid consumption of 3 t/t of ore. Uranium and thorium simultaneous stripping was performed using sodium carbonate solution. In the aqueous stripped it was added sulfuric acid at pH 1.5, followed by a second solvent extraction step using the tertiary amine Alamine 336. The following stripping step was done with a solution of sodium chloride, resulting in a final solution of 23 g L-1 uranium. (author)

Bacterial consortium for copper extraction from sulphide ore consisting mainly of chalcopyrite

Directory of Open Access Journals (Sweden)

E. Romo

2013-01-01

Full Text Available The mining industry is looking forward for bacterial consortia for economic extraction of copper from low-grade ores. The main objective was to determine an optimal bacterial consortium from several bacterial strains to obtain copper from the leach of chalcopyrite. The major native bacterial species involved in the bioleaching of sulphide ore (Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans, Leptospirillum ferrooxidans and Leptospirillum ferriphilum were isolated and the assays were performed with individual bacteria and in combination with At. thiooxidans. In conclusion, it was found that the consortium integrated by At. ferrooxidans and At. thiooxidans removed 70% of copper in 35 days from the selected ore, showing significant differences with the other consortia, which removed only 35% of copper in 35 days. To validate the assays was done an escalation in columns, where the bacterial consortium achieved a higher percentage of copper extraction regarding to control.

Influence of liberation of sulphide minerals on flotation of sedimentary copper ore

Directory of Open Access Journals (Sweden)

Bakalarz Alicja

2017-01-01

Full Text Available Ore liberation is one of the most important parameter in mineral processing, especially in flotation. To separate the valuable components from gangue minerals, it is necessary to liberate one from others. It is achieve primarily through crushing and grinding. These stages are one of the most expensive of mineral production. It is important to determine the adequate mineral liberation which would result in huge savings in the overall cost of flotation plant. The aim of the paper was the analysis of the influence of milling time on the laboratory flotation of the copper ore from stratiform Polish deposit. Three different milling time of copper ore in laboratory ball mill was applied. The flotation results were presented as the recovery-recovery and grade-recovery upgrading curves. The liberation of sulphides and the particle size of sulphides in flotation product were analysed and compared.

Moisture measurements in iron ores, in freight cars, through nuclear techniques

International Nuclear Information System (INIS)

Castagnet, A.C.; Said, M.; Duarte, U.

1975-01-01

The possibility and the advantages of using a nuclear technique for measuring on the spot (in the freight cars) and the moisture content of iron ores are described. The measurements included the determination of the volumetric moisture content and the density. From this values, the moisture content in percentage by weight was calculated. Nuclear Chicago d/M Combination Density-Moisture Probe with a 5 mCi Ra/Be source, and a digital portable scaler, were used. The investigated techniques give good results when the measurements are made directly on the ore surface, and has economical advantages over the gravimetric method by sampling. The probable reasons for both, the aleatory scattering of points and the lack of linear correlation between the values of both methods, when the nuclear measurement is made across the car walls are analized

IAEA sends out samples of uranium ore

Energy Technology Data Exchange (ETDEWEB)

NONE

1966-06-15

Full text: Governments and organizations interested in developing uranium resources will be assisted by a new service, now being inaugurated by the Agency's laboratories, for the distribution of reference samples of uranium ores. This is an addition to the service which began at Seibersdorf in January 1962 for the distribution of calibrated radionuclides, and which has met with a steadily increasing demand. * Uranium deposits consisting of ores with a uranium content in the range 0.5 - 0.05 per cent occur in a number of countries, including developing countries and can present considerable analytical difficulties. In 1962 the Agency asked Member States whether they would be interested in receiving reference samples of uranium ores to assist them in checking their methods of chemical analysis. The response encouraged the Agency to proceed. There is a multiplicity of types of uranium ores and, initially, three of the most commonly occurring have been selected - torbernite, uraninite and carnotite. Member States have provided the laboratory with supplies of these three types of ore. In order to determine the uranium content, samples are sent to leading laboratories throughout the world, so as to arrive at the most accurate values possible. This work has proved to be useful to the laboratories themselves ; in searching for reasons for discrepancies between the different collaborating laboratories, they enlarge their own knowledge and improve their methods. The reference samples are sent out in the form of fine powder, and are available to atomic energy commissions, research laboratories or mining companies. The requesting laboratory, having worked out the analytical process best suited to its needs, is then able to check its results by analysing an IAEA reference sample of known uranium content. By the end of 1966, reference samples will be available of the three ores mentioned, and later also of pure uranium oxide and of uranium oxide containing trace impurities, the

Purification of trona ores by conditioning with an oil-in-water emulsion

Science.gov (United States)

Miller, J. D.; Wang, Xuming; Li, Minhua

2009-04-14

The present invention is a trona concentrate and a process for floating gangue material from trona ore that comprises forming an emulsion, conditioning the trona ore at a high solids content in a saturated trona suspension, and then floating and removing the gangue material. The process for separating trona from gangue materials in trona ore can include emulsifying an oil in an aqueous solution to form an oil-in-water emulsion. A saturated trona suspension having a high solids content can also be formed having trona of a desired particle size. The undissolved trona in the saturated suspension can be conditioned by mixing the saturated suspension and the oil-in-water emulsion to form a conditioning solid suspension of trona and gangue material. A gas can be injected through the conditioning solid suspension to float the gangue material. Thus, the floated gangue material can be readily separated from the trona to form a purified trona concentrate without requirements of additional heat or other expensive processing steps.

Development of Technology for Enrichment of Silver Containing Ores

Science.gov (United States)

Shekiladze, Asmati; Kavtelashvili, Otari; Bagnashvili, Mamuka

2016-10-01

The progress of Georgian economics is substantially associated with a development of new deposits of mineral resources. Among them is the David-Gareji deposit where at present the intensive searching geological works are performed. The work goal involves the elaboration of the technology for processing of silver-containing quartz-barite ores. Without its development the mining of more valuable gold-polymetallic ores is impossible. Because of ore complexity silver and barite are considered in a common technological aspect. The investigations were carried out on the representative samples of quartz-barite ores containing 78-88 g/ton of silver and 27-29 % of silver is a nugget in the form of the simple sulphides and chlorides. The ore is characterized by fine coalescence of barite and ore-generating minerals. Non-ferrous metals haven't any industrial value because of their very low content. Therefore, for the processing of the ores under study the direct selective scheme of flotation enrichment was chosen and the formula of optimal reagent regime was elaborated. Potassium xanthogenate is used as a collector for flotation of silver minerals and pine oil- as a foaming agent. The effect of the pulp - pH and medium temperature on silver flotation was studied. It was established that the silver is actively floats in neutral medium. For barite flotation the various collectors were tested: sulfidezid cotton oil-soap stock, soaps of fatty acids and alkyl sulphates of C12 - C16 row, among the “Baritol” is the most efficient one. Depression of the barren rock was carried out by liquid glass in alkaline medium. The effect of pulp pH on barite flotation has been investigated. The best results were obtained at pH=8.5. The increase of the pulp alkalinity has no essential effect on the indexes of the barite enrichment. Conditional concentrate of the barite is obtained by two fold purification of the main flotation concentrate by the addition of the liquid glass to the re

Analysis of holding time variations to Ni and Fe content and morphology in nickel laterite limonitic reduction process by using coal-dolomite bed

Science.gov (United States)

Abdul, Fakhreza; Pintowantoro, Sungging; Yuwandono, Ridwan Bagus

2018-04-01

With the depletion of nickel sulfide ore resources, the nickel laterit processing become an attention to fulfill nickel world demans. Reducing laterite nickel by using a low cost carbonaceous reductan has proved produces high grade ferronickel alloy. In this research, reduction was carried out to low grade laterite nickel (limonite) with 1.25% nikel content by using CO gas reductant formed by reaction between coal and dolomite. Reduction process preceded by forming brickets mixture from limonit ore, coal, and Na2SO4, then the brickets placed inside crucible bed together with dolomit and reduced at temperature 1400 °C with holding time variations 4, 6, and 8 hours. EDX, XRD, and SEM test were carried out to find out the Ni and nickel grade after reduced, the phases that formed, and the morphology brickets after reduced. The reduction results shows that the highest increase on nickel grade was obtained by 8 hours holding time increasing 5.84 % from initial grade, and the highest recovery was obtained by 6 hours holding time with recovery 88.51 %. While the higest increase on Fe grade was obtained by 4 hours holding time, and the highest recovery Fe was obtained by 4 hours holding time with recovery 85.41%.

Status report from South Africa [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

Robinson, R E [Atomic Energy Board, Pretoria (South Africa)

1967-06-15

Most of the research work on the processing of uranium ores in South Africa is being conducted by the Extraction Metallurgy Division of the S.A. Atomic Energy Board. Nevertheless, a considerable amount of applied research has been done by the different mining groups concerned with the operation of uranium plants, and also by the Transvaal and Orange Free State Chamber of Mines research laboratories. There is, however, very close collaboration between the various research groups and the Atomic Energy Board and the main research described is conducted on a collaborative basis.

Development of a composite collector scheme for flotation of chalcopyrite ore

International Nuclear Information System (INIS)

Khan, M.M.; Ahmad, I.

2005-01-01

Xanthate-type collectors reported for the upgradation of Chalcopyrite ore of North Waziristan area were studied and a new technique was developed, in which -two collectors were used (composite collectors) in the bulk-stage process of froth-flotation to achieve metallurgical grade with maximum recovery. The collectors studied were thiol-type surfactants, such as sodium ethyl xanthate (NaEX), sodium propyl xanthate (NaPX), sodium butyl xanthate (NaBX) and sodium Amyl xanthate (NaAX). Mixed collectors examined were in the varying dosage ratio of (0-100:100-0) through the combination of(i) sodium ethyl xanthate with sodium propyl xanthate, sodium ethyl xanthate with sodium butyl xanthate, sodium ethyl xanthate with sodium amyl xanthate, (ii) sodium propyl xanthate with sodium butyl xanthate, sodium propyl xanthate with sodium amyl xanthate and (iii) sodium butyl xanthate with sodium amyl xanthate. All the remaining flotation parameters were kept constant during the various flotation tests. The results were compared and the conclusions were drawn that the optimum grade in the concentrate was obtained with a mixture having a ratio of 4: 1 with sodium ethyl xanthate and sodium butyl xanthate. Recovery of copper content in the concentrate was achieved with ratio of 2:3 with sodium butyl xanthate and sodium amyl xanthate. (author)

Study on the relation between uranium content and total phosphorus in some sudanese phosphate ore samples

International Nuclear Information System (INIS)

Eltayeb, M. A. H.; Mohammed, A. A.

2003-01-01

In the present work uranium content and total phosphorus were determined in 30 phosphate ore samples collected from Kurun and Uro areas in Nuba Mountains in Sudan. Spectrophotometry technique was used for this purpose. Uranium analysis is based on the use of nitrogen (V) acid for leaching the rock, and treatment with ammonium carbonate solution, whereby uranium (Vi) is kept in solution as its carbonate complex. The ion exchange technique was used for the recovery of uranium. Uranium was eluted from the resin with 1 M hydrochloric acid. In the elute, uranium was determined spectrophotometrically by measurement of absorbance of the yellow uranium (Vi)-8-hydroxyquinolate complex at λ 400 nm. The total phosphorus was measured as (P 2 O 5 %) by treatment of the total liquor with ammonium molybdate solution. The absorbance of the blue complex was measured at λ 880 nm. The results show that a limited relation is existed between uranium content and total phosphorus in phosphate samples from kurun area, which contain 58.8 ppm uranium in average, where there are no relation is existed in phosphate samples from uro area, which contain 200 ppm uranium in average. (Author)

Study on the relation between uranium content and total phosphorus in some sudanese phosphate ore samples

International Nuclear Information System (INIS)

Mohammed, A.A.; Eltayeb, M.A.H.

2003-01-01

In the present work uranium content and total phosphorous were determined in 30 phosphate ore samples collected from Kurun and Uro areas in Nuba mountains in sudan. Spectrophotometry technique was used for this purpose. Uranium analysis is based on the use of nitrogen (V) acid for leaching the rock, and treatment with ammonium carbonate solution, whereby uranium (VI) is kept in solution as its carbonate complex. The ion-exchange technique was used for the recovery of uranium. Uranium was eluted from the resin with 1 M hydrochloric acid. In the elute, uranium was determined spectrophotometrically by measurement of the absorbance of the yellow uranium (VI) - 8- hydroxyquinolate complex at λ 400 nm. The total phosphorus was measured as (P 2 O 5 %) by treatment of the leach liquor with ammonium molybdate solution. The absorbance of the blue complex was measured at λ 880 nm. The results show that a limited relation is existed between uranium content and total phosphorus in phosphate samples from Kurun area, which contain 58.8 ppm uranium in average, where there are no relation is existed in phosphate samples samples from Uro area, which contain 200 ppm uranium in average

On-line sampling of apatite-nepheline ore using apron feeders by gamma-gamma method

Energy Technology Data Exchange (ETDEWEB)

Bliznyuk, G.I.

1981-01-01

The yield flow of an underground mine equipped with a crushing complex was investigated. /sup 241/Am source and 20x20 mm NaI(Tl) crystal were used; the lump size of apatite-nepheline ore was 200 mm, P/sub 2/O/sub 5/ content varied from 10 to 22%. The mean-square error was 1% P/sub 2/O/sub 5/ in 100-ton portions of mined ore. The method can be also applied for sampling iron, copper-nickel, and polymetallic ores.

Challenges facing the North American iron ore industry

Science.gov (United States)

Jorgenson, J.D.

2005-01-01

During the 20th century, the iron ore mining industries of Canada and the United States passed through several periods of transformation. The beginning of the 21st century has seen yet another period of transformation, with the economic failure of a number of steel companies, the acquisition of their facilities by more viable steelmakers, and the consolidation of control within the North American iron ore industry. Changes in Canadian and United States iron ore production and the market control structure involved are analysed. The consolidation of ownership, formation of foreign joint ventures within Nordi America, planned divestitures of upstream activities by steelmakers, and industry changes made to ensure availability of feedstocks will be reviewed. The ttaditional isolation of the Canadian and United States iron ore operations and their strong linkage to downstream steel production will be discussed in the context of a changing global economy. Management-labour conflicts that have taken place and agreements made during 2000 through 2004 will be discussed in the context of the economic environment leading up to these agreements. Cooperative agreements between competing Canadian and United States companies to resolve client needs in processing and blending will be examined. A joint industry-government project designed to use new technology to produce direct reduced iron nuggets of 96 - 98 per cent iron content using non-coking coals will also be assessed. Changes in iron ore transportation methods, ownership and infrastructure will be reviewed for both rail and inland waterway transport between Canadian and United States companies. A brief analysis of social and environmental issues relating to sustainable development of the Canadian-United States iron ore industry will be included.

Estimation of intermediate grade uranium resources. Final report

International Nuclear Information System (INIS)

Lambie, F.W.; Kendall, G.R.; Klahn, L.J.; Davis, J.C.; Harbaugh, J.W.

1980-12-01

The purpose of this project is to analyze the technique currently used by DOE to estimate intermediate grade uranium (0.01 to 0.05% U 3 O 8 ) and, if possible, suggest alternatives to improve the accuracy and precision of the estimate. There are three principal conclusions resulting from this study. They relate to the quantity, distribution and sampling of intermediate grade uranium. While the results of this study must be validated further, they indicate that DOE may be underestimating intermediate level reserves by 20 to 30%. Plots of grade of U 3 O 8 versus tonnage of ore and tonnage U 3 O 8 indicate grade-tonnage relationships that are essentially log-linear, at least down to 0.01% U 3 O 8 . Though this is not an unexpected finding, it may provide a technique for reducing the uncertainty of intermediate grade endowment. The results of this study indicate that a much lower drill hole density is necessary for DOE to estimate uranium resources than for a mining company to calculate ore resources. Though errors in local estimates will occur, they will tend to cancel over the entire deposit

Problems in the separation of radium from uranium ore tailings

Energy Technology Data Exchange (ETDEWEB)

Seeley, F.G.

1976-01-01

The radium content of a representative sandstone type of uranium ore was found to be distributed uniformly according to particle size before leaching, but in sulfuric acid-leached tailings was found predominantly in the -325 mesh fraction. The radium leaching characteristics from both ore and sulfate-leached tailings were investigated. Several 1 M salt solutions showed poor to moderate RaSO/sub 4/ dissolution from ''slimes solids'' tailings, while 3 M HNO/sub 3/ or HCl solutions dissolved approximately 95% of the radium content of either ore or tailings. Tests are reported in which -325 mesh sand particles were coated with alkaline-earth sulfates by a special technique to simulate slime solids tailings. The dissolution of RaSO/sub 4/ from these coated sands was decreased by the presence of BaSO/sub 4/, but increased by the presence of CaSO/sub 4/. The interrelationships in the dissolution of mixtures of CaSO/sub 5/, SrSO/sub 4/, BaSO/sub 4/, and RaSO/sub 4/ are shown, and a generalized equation for the estimation of the dissolution of a minor component is presented.

Define rules for the exporter and importer of minerals or ores containing nuclear elements

International Nuclear Information System (INIS)

1969-01-01

The present resolution establishes regulations for the exporter of minerals or ores containing associated nuclear elements, and for the importer of chemical compounds of technical purity grade, containing a quantity of fissile of fertile materials equal to the existent in the exported material

The North American iron ore industry: a decade into the 21st century

Science.gov (United States)

Jorgenson, John D.; Perez, A. A

2011-01-01

During the 20th century, the iron ore mining industries of Canada and the United States passed through periods of transformation. The beginning of the 21st century has seen another period of transformation, with the failure of a number of steel companies and with consolidation of control within the North American iron ore industry. Canadian and United States iron ore production and the market control structure involved are changing rapidly. Consolidation of ownership, formation of foreign joint ventures, divestitures of upstream activities by steelmakers, and industry changes to ensure availability of feedstocks all played a role in recent developments in the North American iron ore industry. Canadian and U.S. iron ore operations and their strong linkage to downstream production, although isolated, must also be considered within the context of the changing global economy. Projects using new technology to produce direct reduced iron nuggets of 96-98% iron content and other projects designed to produce steel at minesites may once again change the face of the iron ore industry. Social and environmental issues related to sustainable development have had a significant effect on the North American iron ore industry.

Analysis of material flow in a utillzation technology of low grade manganese ore and sulphur coal complementary

Science.gov (United States)

Wang, Bo-Zhi; Deng, Biao; Su, Shi-Jun; Ding, Sang-Lan; Sun, Wei-Yi

2018-03-01

Electrolytic manganese is conventionally produced through low-grade manganese ore leaching in SO2, with the combustion of high sulfur coal. Subsequently the coal ash and manganese slag, produced by the combustion of high sulfur coal and preparation of electrolytic manganese, can be used as raw ingredients for the preparation of sulphoaluminate cement. In order to realize the `coal-electricity-sulfur-manganese-building material' system of complementary resource utilization, the conditions of material inflow and outflow in each process were determined using material flow analysis. The material flow models in each unit and process can be obtained by analyzed of material flow for new technology, and the input-output model could be obtained. Through the model, it is possible to obtain the quantity of all the input and output material in the condition of limiting the quantity of a substance. Taking one ton electrolytic manganese as a basis, the quantity of other input material and cements can be determined with the input-output model. The whole system had thusly achieved a cleaner production level. Therefore, the input-output model can be used for guidance in practical production.

Management of wastes containing radioactivity from mining and milling uranium ores in Northern Australia

International Nuclear Information System (INIS)

Costello, J.M.

1977-01-01

The procedures and controls to achieve safe management of wastes containing radioactivity during the mining and processing of uranium ores are mainly site-specific depending on the nature, location and distribution of the ore and gangue material. Waste rock and below-ore-grade material containing low levels of radioactivity require disposal at the mine site. In open-cut mining the material is generally stockpiled above ground, with revegetation and collection of run-off water. Some material may be used to backfill open cuts. Management of these wastes requires a thorough investigation of groundwater hydrology and surface soil characteristics to control dissipation of radioactive material. Dust containing radon and radioactive particulate is produced during ore milling, and dusts of ore concentrate are generated during calcination and packaging of the yellowcake product. These dusts are managed by ventilation and filtration systems; working conditions and discharges to atmosphere will be according to the Australian Code of Practice on Radiation Protection during Mining and Milling of Uranium Ores. The chemical waste stream from leaching and processing of the uranium ores contains most of the radioactivity resulting from radium and its decay products. Neutralized effluent is discharged into holding ponds for settling solids. The paper describes the nature of wastes containing radioactivity resulting from the mining and milling of uranium, and illustrates modern engineering practices and monitoring procedures to manage the wastes, as described in the Environmental Impact Statement produced by Ranger Uranium Mines Pty Ltd (RUM) for public hearings. (author)

Recovery of uranium low grade ores by froth flotation: study of the texture and synergetic effects of flotation reagents

International Nuclear Information System (INIS)

Duverger, Agathe

2013-01-01

Due to the energy growing demand, uranium low grade ores may be those exploited in the future. Uranium ores conventional treatment does not often use mineral processing such as concentration methods for reducing leaching reagent consumption. The aim of this work is to develop an upgrading process to improve the operating process (alkaline heap leaching) taking into account the mineralogical and textural variability of the ore. The Trekkopje deposit is composed of calcrete and a gypscrete. The uranium bearing mineral is carnotite (K 2 (UO 2 ) 2 [VO 4 ] 2 .3H 2 O). The gangue minerals are composed by silicates, such as quartz, feldspars, micas and Ca-minerals, calcite and gypsum (XRD and ICP-MS analysis). A SEM image processing was used to study the textural properties and the exposed free surface of mineral inclusions in clay clusters. In calcrete milled to -200 μm, 50 % of all carnotite is associated with clay clusters, which are composed by 98 % of palygorskite, 2 % of illite, montmorillonite, and interbedded clays (XRD and microprobe analysis). The carnotite grain size is 95 % less than 70 μm. Calcite is the main inclusion in clay clusters. Indeed, the calcite inclusions average rate in the clay clusters is 12 % and 5 % for carnotite inclusion. And the free exposed surface percentage of these minerals in clay clusters is 3 % and 6 %, thus indicating that the inclusions should not affect the behavior of mixed clay particles. However, ore flotation essays did not verify this hypothesis. Three minerals separation have been proposed based on the mineral ability to consume leaching reagents: separating Ca-minerals from silicates, palygorskite from gangue minerals and carnotite from gangue minerals. A study of silicates and Ca-minerals electrokinetic properties (electrophoresis) was carried out to select the collectors and the optimum pH range for selective flotation. Basic pH near neutral was proved to be optimal for the separation of gangue minerals with cationic

Production of Schwarzmoeller briquets from weakly caking black coal and iron ore

Energy Technology Data Exchange (ETDEWEB)

Naundorf, W.

1986-01-01

Laboratory production is explained of coal and iron ore briquets suitable for metallurgy, using type 33 weakly caking black coal, iron ore concentrates from 3 Soviet mines and sulfite lye as binder. Coal and ore were finely ground to 0.3/0.0 mm grain size, briquetted at high pressure of 150 MPa and at 80 C temperature. The sulfite lye binder content ranged from 4 to 10% in the briquet mixture. Briquets were thermally treated up to 1000 C; the resulting coke lumps (Schwarzmoeller briquets) were analyzed for compression and abrasion strength. Detailed graphs of briquet and coke lump quality parameters are provided. The study shows that high quality metallurgical coke lumps are obtained by briquetting mixtures of black coal and iron ore in a mixture of about 70:30 with 4 to 9% addition of sulfite binder. Compression strength of coke lumps exceeded 35 MPa. The minimum black coal-iron ore mass relation for producing metallurgical coke lumps was 30:70 using 2 types of iron ore concentrates. The influence of adding limestone to the briquetting mixture and of coking conditions resembling the horizontal chamber oven process is also investigated. 5 references.

Microbial Beneficiation of Salem Iron Ore Using Penicillium purpurogenum

Science.gov (United States)

Mishra, M.; Pradhan, M.; Sukla, L. B.; Mishra, B. K.

2011-02-01

High alumina and silica content in the iron ore affects coke rate, reducibility, and productivity in a blast furnace. Iron ore is being beneficiated all around the world to meet the quality requirement of iron and steel industries. Choosing a beneficiation treatment depends on the nature of the gangue present and its association with the ore structure. The advanced physicochemical methods used for the beneficiation of iron ore are generally unfriendly to the environment. Biobeneficiation is considered to be ecofriendly, promising, and revolutionary solutions to these problems. A characterization study of Salem iron ore indicates that the major iron-bearing minerals are hematite, magnetite, and goethite. Samples on average contains (pct) Fe2O3-84.40, Fe (total)-59.02, Al2O3-7.18, and SiO2-7.53. Penicillium purpurogenum (MTCC 7356) was used for the experiment . It removed 35.22 pct alumina and 39.41 pct silica in 30 days in a shake flask at 10 pct pulp density, 308 K (35 °C), and 150 rpm. In a bioreactor experiment at 2 kg scale using the same organism, it removed 23.33 pct alumina and 30.54 pct silica in 30 days at 300 rpm agitation and 2 to 3 l/min aeration. Alumina and silica dissolution follow the shrinking core model for both shake flask and bioreactor experiments.

Preliminary discussion on the application of the geological conceptual model method of uranium ore formation

International Nuclear Information System (INIS)

Ma Guangzhong; Wei Mingji; Luo Yiyue

1992-01-01

The geological conceptual model method of uranium ore formation is established on the basis of geological theory and apriorism. Variables are screened with the application of the method of mathematical geology to find out the variables which are more contributed. In combination with the practical situation in Xikang-Yunnan axis, the variables are compiled and graded so as to determine the optimal ore-controlling factor and to establish the statistical predictive model which is of geological significance. The resources evaluation work has been conducted in the Late Proterozoic geological terrain in Xikang-Yunnan axis

Mining and milling of uranium ore: Indian scenario

International Nuclear Information System (INIS)

Bhasin, J.L.

2001-01-01

The occurrence of uranium minerals in Singhbhum Thrust belt of Eastern India has been known since 1937. In 1950, a team of geologists of the Atomic Minerals Division was assigned to closely examine this 160 km long belt. Since then, several occurrences of uranium have been found and a few of them have sufficient grade and tonnage for commercial exploitation. In 1967, the Government of India formed Uranium Corporation of India Ltd., under the administrative control of the Department of Atomic Energy, with the specific objective of mining and processing of uranium ore and produce uranium concentrates. At present the Corporation operates three underground uranium mines, one ore processing plant with expanded capacity, and two uranium recovery plants. Continuing investigations by the Atomic Mineral Division has discovered several new deposits and favourable areas. The most notable is the large Domiasiat deposit of the sandstone type found in the State of Meghalaya. This deposit is now being considered for commercial exploitation using the in-situ leaching technology. (author)

Test operation of the uranium ore processing pilot plant and uranium conversion plant

International Nuclear Information System (INIS)

Suh, I.S.; Lee, K.I.; Whang, S.T.; Kang, Y.H.; Lee, C.W.; Chu, J.O.; Lee, I.H.; Park, S.C.

1983-01-01

For the guarantee of acid leaching process of the Uranium Ore Processing Pilot Plnat, the KAERI team performed the test operation in coorperation with the COGEMA engineers. The result of the operation was successful achieving the uranium leaching efficiency of 95%. Completing the guarentee test, a continuous test operation was shifted to reconform the reproducibility of the result and check the functions of every units of the pilot plant feeding the low-grade domestic ore, the consistency of the facility was conformed that the uranium can easily be dissolved out form the ore between the temperature range of 60degC-70degC for two hours of leaching with sulfuric acid and could be obtained the leaching efficiency of 92% to 95%. The uranium recovery efficiencies for the processes of extraction and stripping were reached to 99% and 99.6% respectively. As an alternative process for the separation of solid from the ore pulp, four of the Counter Current Decanters were shifted replacing the Belt Filter and those were connected in a series, which were not been tested during the guarantee operation. It was found out that the washing efficiencies of the ore pulp in each tests for the decanters were proportionally increased according to the quantities of the washing water. As a result of the test, it was obtained that washing efficiencies were 95%, 85%, 83% for the water to ore ratio of 3:1, 2:1, 1.5:1 respectively. (Author)

Standard values of quality and ore mining costs in management of multi-plant mining company

Energy Technology Data Exchange (ETDEWEB)

Kudelko, Jan [KGHM CUPRUM Research and Development Center, Wroclaw (Poland); Wirth, Herbert [KGHM Polska Miedz S.A., Lubin (Poland)

2010-03-15

Profitability of copper deposit mining depends on three basic variables, electrolytic copper price, manufacturing and selling costs of copper and company property involved in production process. If the company property is adjusted to its tasks then the mining profiability depends on costs of copper mining and selling, because the price is the external variable defined by the market. We can shape the costs in two (complementary) ways, traditionally, reducing the labor, material and power consumption, and by adjusting the quality of mined ore (copper content) to the level required by the current copper prices. Required quality of copper ore in the whole company we determine according to the accepted profitability criteria and then we determine quality standard for individual mines. Algorithms determining the ore quality standard resulting from current market price of copper are presented in the paper. Calculation models for the mined ore quality standards, unit mining costs per one ton of copper, electrolytic copper production and ore output are given. Standards were established for one variable assuming that the other variables are determined in this calculation. Innovative solution, presented in the paper, is the method of decomposition of the company controllable variables into the tasks for individual mines providing reaching the targets to the whole technological circuit. Using the models, having relatively few data, it will be possible to calculate quickly the values which are interesting for managers such as for example the prognosis of rate of return (economic or operational), required copper content in the mined ore for the whole company and individual mines at given rate of return or boundary level of copper content in comparison with cost and production level. Examples of calculation are provided. (orig.)

Research on geochronology and uranium source of sandstone-hosted uranium ore-formation in major uranium-productive basins, Northern-China

International Nuclear Information System (INIS)

Xia Yuliang; Liu Hanbin; Lin Jinrong; Fan Guang; Hou Yanxian

2004-12-01

A method is developed for correcting uranium content in uranium ore samples by considering the U-Ra equilibrium coefficient, then a U-Pb isochron is drawn up. By performing the above correction ore-formation ages of sandstone-hosted uranium mineralization which may be more realistic have been obtained. The comparative research on U-Pb isotopic ages of detritic zircon in ore-hosting sandstone and zircon in intermediate-acid igneous rocks in corresponding provenance area indicates that the ore-hosting sandstone is originated from the erosion of intermediate-acid igneous rocks and the latters are the material basis for the formation of the uranium-rich sandstone beds. On the basis of the study on U-Pb isotopic system evolution of the provenance rocks and sandstones from ore-hosting series, it is verified that the uranium sources of the sandstone-hosted uranium deposit are: the intermediate-acid igneous rocks with high content of mobile uranium, and the sandstone bodies pre-concentrated uranium. (authors)

Studies on geneses of Lianshanguan granites and Lianshanguan uranium ore deposit

International Nuclear Information System (INIS)

Zhang Jiafu; Xu Guoqing; Wang Wenguang

1994-02-01

Based on the field work, and through the studies of thin-sections, minerals fluid inclusions, isotope geology, rare-earth elements and U-content in rocks and minerals, it is suggested that Lianshanguan granites are of magmatization genesis with multistage. The genetic model of mineralization of Lianshanguan uranium ore deposit is the magmatization-hydrothermal-filled uranium type. The role of mineralization of uranium ore deposit in that area is discussed. Furthermore, the direction of prospecting and following prospecting criteria for similar deposits in this area are also given

The role of metasomatism in the balance of halogens in ore-forming process at porphyry Cu-Mo deposits

Science.gov (United States)

Berzina, A. N.

2009-04-01

Volatile components play an important role in the evolution of ore-magmatic systems and their ore potential. Of special interest are fluorine and chlorine compounds that principally control the transportation of ore elements by the fluid in a magmatic process and under high-temperature hydrothermal conditions. Study of the evolution of fluorine-chlorine activity in the ore-forming process and their source is usually based on analysis of their magmatic history, whereas the additional source of fluorine and chlorine released during metasomatic alteration of rocks hosting mineralization is poorly discussed in the existing literature. Based on microprobe data on Cl and F abundances in halogen-containing minerals (biotite, amphibole, apatite, titanite) in intrusive rocks and their hydrothermally altered varieties, the role of metasomatic processes in the balance of volatiles in the ore-forming system is discussed by the example of porphyry Cu-Mo deposits of Siberia (Russia) and Mongolia. Two groups of the deposits are considered: copper-molybdenum (Erdenetiin Ovoo, Mongolia and Aksug, Russia) with prevailing propylitic and phyllic alteration and molybdenum-copper (Sora, Russia), with predominant potassic alteration. All types of hydrothermal alterations have led to drastic decrease in Cl contents in metasomatic minerals as compared with halogen-containing magmatic minerals. All studied deposits (particularly those where propylitic and phyllic alteration were developed) show a nearly complete chlorine removal from altered halogen-containing rock-forming minerals (biotite and amphibole). The Cl content in amphibole decreases several times at the stage of replacement with actinolite in the process of propylitization. In the later chlorites (ripidolite and brunsvigite) that replace amphibole, actinolite, and biotite, chlorine is not detected by microprobe (detection limit 0.01-0.02% Cl). Chlorine was also not detected in white micas (muscovite-phengite series) in quartz

Thirty years of uranium ore processing in Spain

International Nuclear Information System (INIS)

Josa, J.M.

1982-01-01

Spanish background in the uranium ore processing includes ores from pegmatitic type deposits, vein deposits, sandstone, enrichments in metamorphic rocks, radioactive coals and non-conventional sources of uranium, such as wet phosphoric acid or copper liquors. Some tests have also done in order to recover uranium from very low grade paleozoic quartzites. We have also been involved in by-products recovery (copper) from uranium ores. The technologies that have been used are: physical concentration, combustion and roasting, conventional alkaline or acid methods, pressure, heap and bacteria leaching. Special attention was paid to recover uranium from the pregnant liquors and to develop suited equipment for it; solvent extraction and continuous ion exchange equipment was carefully studied. We have been involved in commercial size (500-3000 t/d) mills, but we have also developed transportable and reussable modular plants specially designed and suited to recover uranium from small and isolated deposits. In both cases the reduction of the environmental impact was taken in account. Spanish experience also includes nuclear purification aspects in order to get uranium nuclear compounds (ADU, UO 2 , UF 4 and UF 6 ). Wet (nitric-TBP) and dry (Fluid-bed) methods have been used. The best of these 30 years of experience in studies and in industrial practice, together with our new developments towards the future, could become in a good contribution for the medium size countries which are going to develop its own uranium industry. The way for these countries could be easier if they know what is valuable and what must be avoid in the uranium ore processing development. In this aim the whole paper was thought and written. (author)

Management of wastes containing radioactivity from mining and milling of uranium ores in Northern Australia

International Nuclear Information System (INIS)

Costello, J.M.

1977-01-01

The procedures and controls to achieve safe management of wastes containing radioactivity during the mining and processing of uranium ores are mainly site specific depending on the nature, location and distribution of the ore and gangue material. Waste rock and below-ore-grade material containing low levels of radioactivity require disposal at the mine site. In open cut mining the material is generally stockpiled above ground, with revegetation and collection of run-off water. Some material may be used to backfill open cuts. Management of these wastes requires a thorough investigation of ground water hydrology and surface soil characteristics to control dissipation of radioactive material. Dust containing radon and radioactive particulate is produced during ore milling, and dusts of ore concentrate are generated during calcination and packaging of the yellowcake product. These dusts are managed by ventilation and filtration systems, working conditions, and discharges to atmosphere will be according to the Australian Code of Practice on Radiation Protection during Mining and Milling of Uranium Ores. The chemical waste stream from leaching and processing of the uranium ores contains the majority of the radioactivity resulting from radium and its decay products. Neutralised effluent is discharged into holding ponds for settling of solids. This paper describes the nature of wastes containing radioactivity resulting from the mining and milling of uranium, and illustrates modern engineering practices and monitoring procedures to manage the wastes, as described in the Environmental Impact statement produced by Ranger Uranium Mines Proprietary Limited for public hearings

Novel Binders and Methods for Agglomeration of Ore

Energy Technology Data Exchange (ETDEWEB)

S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

2006-09-30

Heap leaching is one of the methods being used to recover metal from low grade ore deposits. The main problem faced during heap leaching is the migration of fine grained particles through the heap, forming impermeable beds which result in poor solution flow. The poor solution flow leads to less contact between the leach solution and the ore, resulting in low recovery rates. Agglomeration of ore into coarse, porous masses prevents fine particles from migrating and clogging the spaces and channels between the larger ore particles. Currently, there is one facility in the United States which uses agglomeration. This operation agglomerates their ore using leach solution (raffinate), but is still experiencing undesirable metal recovery from the heaps due to agglomerate breakdown. The use of a binder, in addition to the leach solution, during agglomeration would help to produce stronger agglomerates that did not break down during processing. However, there are no known binders that will work satisfactorily in the acidic environment of a heap, at a reasonable cost. As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. Increasing copper recovery in heap leaching by the use of binders and agglomeration would result in a significant decrease in the amount of energy consumed. Assuming that 70% of all the leaching heaps would convert to using agglomeration technology, as much as 1.64*10{sup 12} BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, which is equivalent to saving approximately 18% of the energy currently being used in leaching heaps. For every week a leach cycle was decreased, a savings of as much as 1.23*10{sup 11} BTU per week would result. This project has identified several acid-resistant binders and agglomeration procedures. These binders and experimental procedures will be able to be used for use in improving the energy efficiency of

On-line and bulk analysis of iron ore and bauxite

International Nuclear Information System (INIS)

Holmes, R.J.; Roczniok, A.F.

1983-01-01

A number of analysis techniques based on neutron and gamma radiation have been developed for the mining industry. Current projects include the measurement of annihilation radiation arising from pair production for the on-line determination of the iron content of iron ores, and the construction of a demonstration bauxite analyser based on fast-neutron activation analysis for the simultaneous determination of aluminium and silicon content

Complex mineralization at large ore deposits in the Russian Far East

Science.gov (United States)

Schneider, A. A.; Malyshev, Yu. F.; Goroshko, M. V.; Romanovsky, N. P.

2011-04-01

Genetic and mineralogical features of large deposits with complex Sn, W, and Mo mineralization in the Sikhote-Alin and Amur-Khingan metallogenic provinces are considered, as well as those of raremetal, rare earth, and uranium deposits in the Aldan-Stanovoi province. The spatiotemporal, geological, and mineralogical attributes of large deposits are set forth, and their geodynamic settings are determined. These attributes are exemplified in the large Tigriny Sn-W greisen-type deposit. The variation of regional tectonic settings and their spatial superposition are the main factor controlling formation of large deposits. Such a variation gives rise to multiple reactivation of the ore-magmatic system and long-term, multistage formation of deposits. Pulsatory mineralogical zoning with telescoped mineral assemblages related to different stages results in the formation of complex ores. The highest-grade zones of mass discharge of hydrothermal solutions are formed at the deposits. The promising greisen-type mineralization with complex Sn-W-Mo ore is suggested to be an additional source of tungsten and molybdenum. The Tigriny, Pravourminsky, and Arsen'evsky deposits, as well as deposits of the Komsomol'sk and Khingan-Olonoi ore districts are examples. Large and superlarge U, Ta, Nb, Be, and REE deposits are localized in the southeastern Aldan-Stanovoi Shield. The Ulkan and Arbarastakh ore districts attract special attention. The confirmed prospects of new large deposits with Sn, W, Mo, Ta, Nb, Be, REE, and U mineralization in the south of the Russian Far East assure expediency of further geological exploration in this territory.

Phase transformations of siderite ore by the thermomagnetic analysis data

Energy Technology Data Exchange (ETDEWEB)

Ponomar, V.P., E-mail: vitaliyponomar.vp@gmail.com; Dudchenko, N.O.; Brik, A.B.

2017-02-01

Thermal decomposition of Bakal siderite ore (that consists of magnesium siderite and ankerite traces) was investigated by thermomagnetic analysis. Thermomagnetic analysis was carried-out using laboratory-built facility that allows automatic registration of sample magnetization with the temperature (heating/cooling rate was 65°/min, maximum temperature 650 °C) at low- and high-oxygen content. Curie temperature gradually decreases with each next cycles of heating/cooling at low-oxygen content. Curie temperature decrease after 2nd cycle of heating/cooling at high-oxygen content and do not change with next cycles. Final Curie temperature for both modes was ~320 °C. Saturation magnetization of obtained samples increases up to 20 Am{sup 2}/kg. The final product of phase transformation at both modes was magnesioferrite. It was shown that intermediate phase of thermal decomposition of Bakal siderite ore was magnesiowustite. - Highlights: • Mg-siderite decomposition was investigated by thermomagnetic analysis. • Magnetization and Curie temperature change with each next cycle of heating/cooling. • Magnesioferrite is the final phase of Mg-siderite thermal decomposition. • Transformation exclude the hematite formation.

New insights into the extraction of invisible gold in a low-grade high-sulfur Carlin-type gold concentrate by bio-pretreatment

Science.gov (United States)

Qiu, Xiao-bin; Wen, Jian-kang; Huang, Song-tao; Yang, Hong-ying; Liu, Mei-lin; Wu, Biao

2017-10-01

To extract gold from a low-grade (13.43 g/t) and high-sulfur (39.94wt% sulfide sulfur) Carlin-type gold concentrate from the Nibao deposit, Guizhou, a bio-pretreatment followed by carbon-in-pulp (CIP) cyanide leaching process was used. Various methods were used to detect the low-grade gold in the concentrate; however, only time-of-flight secondary-ion mass spectrometry (TOF-SIMS) was successful. With bio-pretreatment, the gold recovery rate increased by approximately 70.16% compared with that obtained by direct cyanide leaching of the concentrate. Various attempts were made to increase the final gold recovery rate. However, approximately 20wt% of the gold was non-extractable. To determine the nature of this non-extractable gold, mineralogy liberation analysis (MLA), formation of secondary product during the bio-pretreatment, and the preg-robbing capacity of the carbonaceous matter in the ore were investigated. The results indicated that at least four factors affected the gold recovery rate: gold occurrence, tight junctions of gold-bearing pyrite with gangue minerals, jarosite coating of the ore, and the carbonaceous matter content.

The flotation of Roşia Poieni copper ore in column machine, with non-polar oils addition

Directory of Open Access Journals (Sweden)

Ciocani V.

2005-11-01

Full Text Available The most important natural resource of copper in Romania is the ore deposit of Roşia Poieni. At present, the utilization of Roşia Poieni poorphyry copper ore is possible by extraction in quarry of the mass ore and mineral processing into a technological flux with modest results for the value of metal recovery in concentrate 70-72 % and an average contents of 16,5 % Cu. Our researches were directed to studies regarding test and utilisation of special procedure of flotation – addition of the non-polar oil – applied to advanced grinding ore with column type machines.

Fluid evolution and ore genesis of the Dalingshang deposit, Dahutang W-Cu ore field, northern Jiangxi Province, South China

Science.gov (United States)

Peng, Ning-Jun; Jiang, Shao-Yong; Xiong, Suo-Fei; Pi, Dao-Hui

2018-02-01

The Dalingshang W-Cu deposit is located in the North section of the Dahutang ore field, northern Jiangxi Province, South China. Vein- and breccia-style tungsten-copper mineralization is genetically associated with Mesozoic S-type granitic rocks. Infrared and conventional microthermometric studies of both gangue and ore minerals show that the homogenization temperatures for primary fluid inclusions in wolframite ( 340 °C) are similar to those in scheelite ( 330 °C), but about 40 °C higher than those of apatite ( 300 °C) and generally 70 °C higher than those in coexisting quartz ( 270 °C). Laser Raman analysis identifies CH4 and N2 without CO2 in fluid inclusions in scheelite and coexisting quartz, while fluid inclusions in quartz of the sulfide stage have variable CO2 content. The ore-forming fluids overall are characterized by high- to medium-temperature, low-salinity, CH4, N2, and/or CO2-bearing aqueous fluids. Chalcopyrite, muscovite, and sphalerite are the most abundant solids recognized in fluid inclusions from different ores. The H-O-S-Pb isotope compositions favor a dominantly magmatic origin for ores and fluids, while some depleted δ34S values (- 14.4 to - 0.9‰) of sulfides from the sulfide stage are most likely produced by an increase of oxygen fugacity, possibly caused by inflow of oxidized meteoric waters. The microthermometric data also indicate that a simple cooling process formed early scheelite and wolframite. However, increasing involvement of meteoric waters and fluid mixing may trigger a successive deposition of base metal sulfides. Fluid-rock interaction was critical for scheelite mineralization as indicated by in-situ LA-ICP-MS analysis of trace elements in scheelite.

Thallium-rich pyrite ores from the Apuan Alps, Tuscany, Italy:constraints for their origin and environmental concerns

Science.gov (United States)

D'Orazio, Massimo; Biagioni, Cristian; Dini, Andrea; Vezzoni, Simone

2017-06-01

The southern sector of the Apuan Alps (AA) massif, Tuscany, Italy, is characterized by the occurrence of a series of baryte-pyrite-iron oxide orebodies whose Tl-rich nature was recognized only recently. The geochemistry of the pyrite ore was investigated through inductively coupled plasma mass spectrometry. In addition, lead isotope data for selected pyrite ores from AA were collected. Pyrite ores are characterized by a complex geochemistry, with high concentrations of Tl (up to 1100 μg/g) coupled with high As and Sb contents; the Co/Ni ratio is always <1. Geochemical data of pyrite and marcasite ore samples from other mining districts of Tuscany have been collected in order to compare them with those from the AA. These samples usually have very low Tl content (less than 2 μg/g) and high to very high Co/Ni and As/Sb ratios. Only some samples from the Sb-Hg ore deposits showed very high Tl concentrations (up to 3900 μg/g). Another difference is related to the lead isotope composition, with pyrite ores from AA markedly less radiogenic than those from the other deposits from Tuscany. Geochemical data of pyrite ores from AA give new insights on the genesis of the baryte-pyrite-iron oxide orebodies, relating their formation to low-temperature hydrothermal systems active during early Paleozoic; in addition, these data play a fundamental role in assessing the environmental impact of these deposits.

Studies on uranium ore processing

International Nuclear Information System (INIS)

Kim, C.H.; Park, S.W.; Lim, J.K.; Chung, M.K.

1981-01-01

Chemical and chemical engineering techniques of the uranium ore processing established by France COGEMA (Compagnie Generale des Matieres Nucleaires) have been comprehensively reviewed in preparation for successful test operation of the pilot plant to be completed by the end of 1981. It was found that the amount of sulfuric acid (75 Kg/t, ore) and sodium chlorate (2.5 Kg/t, ore) recommended by COGEMA should be increased up to 100 Kg/t, ore and 10 Kg/t, ore respectively to obtain satisfactory leach of uranium for some ore samples produced at the different pits of Goesan uranium mine. Conditions of the other processes such as solvent extraction, stripping, and precipitation of yellow cake were generally agreed with the results of intensive studies done by this laboratory

New interpretation of the dominant ore-controlling factor of the uranium ore field No. 322

International Nuclear Information System (INIS)

Liu Xiang; Yang Chongqiu

1996-01-01

The NE-trending fault structures in ore field NO. 322 are characterized by compress-shearing, left-Lateral left-slipping, having an obvious control over the Localisation of the ore field No. 322, and are the dominant ore-controlling factor of the ore field NO.322. Resulting from the sinistral displacement of the NE-trending fault, there is a pull-apart basin in the Feng Zhou area. The formation and evolution of the NE-trending fault zone and the Feng Zhou basin control the formation of uranium deposits of ore field No. 322

Beneficiation of the gold bearing ore by gravity and flotation

Science.gov (United States)

Gül, Alim; Kangal, Olgaç; Sirkeci, Ayhan A.; Önal, Güven

2012-02-01

Gold concentration usually consists of gravity separation, flotation, cyanidation, or the combination of these processes. The choice among these processes depends on the mineralogical characterization and gold content of the ore. Recently, the recovery of gold using gravity methods has gained attention because of low cost and environmentally friendly operations. In this study, gold pre-concentrates were produced by the stepwise gravity separation and flotation techniques. The Knelson concentrator and conventional flotation were employed for the recovery of gold. Gold bearing ore samples were taken from Gümüşhane Region, northern east part of Turkey. As a result of stepwise Knelson concentration experiments, a gold concentrate assaying around 620 g/t is produced with 41.4wt% recovery. On the other hand, a gold concentrate about 82 g/t is obtained with 89.9wt% recovery from a gold ore assaying 6 g/t Au by direct flotation.

Technical application of agglomerated acidic heap leaching of clay-bearing uranium ore in China

International Nuclear Information System (INIS)

Zeng Yijun; Li Jianhua; Li Tieqiu; Zhong Pingru

2002-01-01

The permeability of ore mass has a great influence on the leaching period of heap leaching and the leaching efficiency, hence the uranium ores with high content of clay is difficult to acidic heap leaching. The Research Institute of Uranium Mining has engaged several years studies on the cementing agents of acidic agglomeration, agglomeration conditions, as well as the curing measures of agglomerated balls. On the basis of these studies, several types of clay-bearing ores have been tested with good results. The technique of agglomerated acidic heap leaching has been successfully applied in a uranium mine. Since agglomeration has effectively increased the permeability of ore heap, its leaching period is decreased from 200 days to 60 days, the leaching efficiency is increased to 96% from less than 40% comparing with direct heap leaching program

Plutonium content in uranium minerals

International Nuclear Information System (INIS)

Garzon Ruiperez, L.

1975-01-01

Starting from a ore model constituted by a uniformily dispersed UO 2 into a granite matrix, the Pu/U ratio as a function of UO 2 concentration in the ore have been deduced. The calculated values are roughly one or two orders of magnitude less than the experimental ones carried out in several types of ores. However, taking into account the H content in the matrix (as a water component) the obtained values agree satisfactorili with the experimental ones. (author) [es

Practice of the counter-current trickle leaching of uranium ore by refreshed liquor of bacterial oxidation

International Nuclear Information System (INIS)

Chen Shian; Huang Xiangfu; Fan Baotuan

1995-01-01

The uranium ore of the Mine No. 753 is a high-silicate type primary one, in which the tetravalent uranium accounts for 85%, and the uranium grade is in the range of 0.36% to 0.442%. To reduce the engineering investment and the operating cost a four-stage counter-current trickle leaching pilot-plant test was carried out with the leaching time 50 days and acid consumption 38 kg per ton of ore, and the recovery of more than 95% was obtained. Using the counter-current trickle leaching mode and controlling the limit concentration of the harmful matters in the bacterial leaching liquor, the latter can be effectively oxidized by the synchronical regeneration. A trickle leaching comparative test of 25 ton ore single heap also gave a good result of more than 95% in extraction rate, and 30% acid consumption was saved and the 2.0% pyrolusite (containing MnO 2 40%) was eliminated. This process is feasible in technology and worth-while in economy for treating the uranium ore of Mine No. 753, and provides a new method of uranium ore trickle leaching

Estimation of intermediate-grade uranium resources II. Proposed method for estimating intermediate-grade uranium resources in roll-front deposits. Final report

International Nuclear Information System (INIS)

Lambie, F.W.; Yee, S.N.

1981-09-01

The purpose of this and a previous project was to examine the feasibility of estimating intermediate grade uranium (0.01 to 0.05% U 3 O 8 ) on the basis of existing, sparsely drilled holes. All data are from the Powder River Basin in Wyoming. DOE makes preliminary estimates of endowment by calculating an Average Area of Influence (AAI) based on densely drilled areas, multiplying that by the thickness of the mineralization and then dividing by a tonnage factor. The resulting tonnage of ore is then multiplied by the average grade of the interval to obtain the estimate of U 3 O 8 tonnage. Total endowment is the sum of these values over all mineralized intervals in all wells in the area. In regions where wells are densely drilled and approximately regularly spaced this technique approaches the classical polygonal estimation technique used to estimate ore reserves and should be fairly reliable. The method is conservative because: (1) in sparsely drilled regions a large fraction of the area is not considered to contribute to endowment; (2) there is a bias created by the different distributions of point grades and mining block grades. A conservative approach may be justified for purposes of ore reserve estimation, where large investments may hinge on local forecasts. But for estimates of endowment over areas as large as 1 0 by 2 0 quadrangles, or the nation as a whole, errors in local predictions are not critical as long as they tend to cancel and a less conservative estimation approach may be justified.One candidate, developed for this study and described is called the contoured thickness technique. A comparison of estimates based on the contoured thickness approach with DOE calculations for five areas of Wyoming roll-fronts in the Powder River Basin is presented. The sensitivity of the technique to well density is examined and the question of predicting intermediate grade endowment from data on higher grades is discussed

Ore reserve evalution, through geostatistical methods, in sector C-09, Pocos de Caldas, MG-Brazil

International Nuclear Information System (INIS)

Guerra, P.A.G.; Censi, A.C.; Marques, J.P.M.; Huijbregts, Ch.

1978-01-01

In sector C-09, Pocos de Caldas in the state of Minas Gerais, geostatistical techniques have been used to evaluate the tonnage of U 3 O 8 and associated minerals and to delimit ore from sterile areas. The calculation of reserve was based on borehole information including the results of chemical and/or radiometric analysis. Two-and three dimensional evalutions were made following the existing geological models. Initially, the evaluation was based on chemical analysis using the more classical geostatistical technique of kriging. This was followed by a second evaluation using the more recent technique of co-kriging which permited the incorporation of radiometric information in the calculations. The correlation between ore grade and radiometric was studied using the method of cross-covariance. Following restrictions imposed by mining considerations, a probabilistic selection was made of blocks of appropriate dimensions so as to evaluate the grade tonnage curve for each panel. (Author) [pt

Phytostabilisation potential of lemon grass (Cymbopogon flexuosus (Nees ex Stend) Wats) on iron ore tailings.

Science.gov (United States)

Mohanty, M; Dhal, N K; Patra, P; Das, B; Reddy, P S R

2012-01-01

The present pot culture study was carried out for the potential phytostabilisation of iron ore tailings using lemon grass (Cymbopogon flexuosus) a drought tolerant, perennial, aromatic grass. Experiments have been conducted by varying the composition of garden soil (control) with iron ore tailings. The various parameters, viz. growth of plants, number of tillers, biomass and oil content of lemon grass are evaluated. The studies have indicated that growth parameters of lemon grass in 1:1 composition of garden soil and iron ore tailings are significantly more (-5% increase) compared to plants grown in control soil. However, the oil content of lemon grass in both the cases more or less remained same. The results also infer that at higher proportion of tailings the yield of biomass decreases. The studies indicate that lemongrass with its fibrous root system is proved to be an efficient soil binder by preventing soil erosion.

Nuclear-geophysical methods as a basis of progressive technology of ore quality control in mining industry

International Nuclear Information System (INIS)

Mejer, V.A.

1976-01-01

The significance of nuclear physics methods in the mining industry is demonstrated using examples of applying the X-ray diffraction method to the delimitation of lead-zinc and tin ores in exploratory wells, faces of mine workings and to a quick estimation of metal contents in hacked-off rocks and market payable ore. Their implementation at all stages of the exploration and development of deposits would improve the extraction of ores and reduce losses of the raw material during technological treatment. Owing to the rapidity and operativeness of control over the quality of ores at all stages of geological prospecting and mining, nuclear physics methods can provide a basis for technological progress in the mining industry

Early Local Activity in Temporal Areas Reflects Graded Content of Visual Perception

Directory of Open Access Journals (Sweden)

Chiara Francesca Tagliabue

2016-04-01

Full Text Available In visual cognitive neuroscience the debate on consciousness is focused on two major topics: the search for the neural correlates of the different properties of visual awareness and the controversy on the graded versus dichotomous nature of visual conscious experience. The aim of this study is to search for the possible neural correlates of different grades of visual awareness investigating the Event Related Potentials (ERPs to reduced contrast visual stimuli whose perceptual clarity was rated on the four-point Perceptual Awareness Scale (PAS. Results revealed a left centro-parietal negative deflection (Visual Awareness Negativity; VAN peaking at 280-320 ms from stimulus onset, related to the perceptual content of the stimulus, followed by a bilateral positive deflection (Late Positivity; LP peaking at 510-550 ms over almost all electrodes, reflecting post-perceptual processes performed on such content. Interestingly, the amplitude of both deflections gradually increased as a function of visual awareness. Moreover, the intracranial generators of the phenomenal content (VAN were found to be located in the left temporal lobe. The present data thus seem to suggest 1 that visual conscious experience is characterized by a gradual increase of perceived clarity at both behavioral and neural level and 2 that the actual content of perceptual experiences emerges from early local activation in temporal areas, without the need of later widespread frontal engagement.

Geology and ore deposits of the Section 23 Mine, Ambrosia Lake District, New Mexico

Science.gov (United States)

Granger, H.C.; Santos, E.S.

1982-01-01

The section 23 mine is one of about 18 large uranium mines opened in sandstones of the fluvial Westwater Canyon Member of the Jurassic Morrison Formation in the Ambrosia Lake mining district during the early 1960s. The Ambrosia Lake district is one of several mining districts within the Grants mineral belt, an elongate zone containing many uranium deposits along the southern flank of the San Juan basin. Two distinct types of ore occur in the mine. Primary ore occurs as peneconcordant layers of uranium-rich authigenic organic matter that impregnates parts of the reduced sandstone host rocks and which are typically elongate in an east-southeast direction subparallel both to the sedimentary trends and to the present-day regional strike of the strata. These are called prefault or trend ores because of their early genesis and their elongation and alinement. A second type of ore in the mine is referred to as postfault, stacked, or redistributed ore. Its genesis was similar to that of the roll-type deposits in Tertiary rocks of Wyoming and Texas. Oxidation, related to the development of a large tongue of oxidized rock extending from Gallup to Ambrosia Lake, destroyed much of the primary ore and redistributed it as massive accumulations of lower grade ores bordering the redox interface at the edge of the tongue. Host rocks in the southern half of sec. 23 (T. 14 N., R. 10 W.) are oxidized and contain only remnants of the original, tabular, organic-rich ore. Thick bodies of roll-type ore are distributed along the leading edge of the oxidized zone, and pristine primary ore is found only near the north edge of the section. Organic matter in the primary ore was derived from humic acids that precipitated in the pores of the sandstones and fixed uranium as both coffinite and urano-organic compounds. Vanadium, molybdenum, and selenium are also associated with the ore. The secondary or roll-type ores are essentially free of organic carbon and contain uranium both as coffinite and

Technological studies on the Manisa-Koprubasi uranium ores of Turkey

International Nuclear Information System (INIS)

Sagdik, U.

1980-01-01

At the end of the laboratory and pilot plant scale technological experiments, three main types of ore have been classified: (i) Kasar type: The ores consist of secondary uranium mineralization (autunite, meta-autunite and torbenite) in loosely consolidated sands, gravels and clays of Neogene Age. Heap leaching has been carried out on 100 and 1000 t ore samples (0.05% U 3 O 8 ) under economical conditions, such as 20 to 40 kg of H 2 SO 4 per tonne of ore at ambient temperature; original size -20 cm, solid/liquid ratio of 10, 20 days, and 90% recovery of uranium has been reached. The uraniferous solutions (1 to 2 g of U 3 O 8 per litre) obtained from the heap leaching operations were purified in a solvent extraction unit with a capacity of 100 ltr/h by using an Alamine 336-kerosene-decanol solution. The uranium in the purified and concentrated solutions (15 g of U 3 O 8 per litre) was then precipitated as a yellow cake with 65 to 75% U 3 O 8 content by means of magnesia milk. (ii) Tasharman type: No specific uranium mineral has been detected in the mineralogical determination, although uranium is disseminated in phosphate minerals as dahllite and apatite. Uranium in the ore has been leached under rather uneconomical conditions; 100 kg of H 2 SO 4 per tonne of ore, particle size -1 cm, 25 0 C, 30 days. In the SX-treatment of pregnant solutions phosphate ions, higher acidity than pH 1, and compounds formed as a chemical precipitation, hindered the SX-recoveries. In such cases, the addition of acid, dilution of pregnant solutions, membrane filtration, or 40 0 C temperature have been applied to decrease the uranium loss in the raffinate. (iii) Carbonate type: Even if alkaline leaching at 65 0 C, or leaching with 400 kg of H 2 SO 4 per tonne of ore, was carried out on -200 mesh ore samples, no acceptable uranium recoveries were obtained

Ore sorting

International Nuclear Information System (INIS)

Hawkins, A.P.; Richards, A.W.

1982-01-01

In an ore sorting apparatus, ore particles are bombarded with neutrons in a chamber and sorted by detecting radiation emitted by isotopes of elements, such as gold, forming or contained in the particles, using detectors and selectively controlling fluid jets. The isotopes can be selectively recognised by their radiation characteristics. In an alternative embodiment, shorter life isotopes are formed by neutron bombardment and detection of radiation takes place immediately adjacent the region of bombardment

Heap leaching of clay ish uranium ores; Lixiviacion estatica de minerales arcillosos de uranio

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, E; Sedano, A

1973-07-01

This paper describes an experimental facility, built near El Lobo mine. In it we study the beneficiation of low-grade uranium ore. The mineral has a great amount of clay and fines. The flow-sheet used has four steps: head leaching, ph-ajustement, ion-exchange and participation. We show, also, the most interesting results. (Author)

Acid-base properties and surface complexation modeling of phosphate anion adsorption by wasted low grade iron ore with high phosphorus.

Science.gov (United States)

Yuan, Xiaoli; Bai, Chenguang; Xia, Wentang; An, Juan

2014-08-15

The adsorption phenomena and specific reaction processes of phosphate onto wasted low grade iron ore with high phosphorus (WLGIOWHP) were studied in this work. Zeta potential and Fourier transform infrared spectroscopy (FTIR) analyses were used to elucidate the interaction mechanism between WLGIOWHP and aqueous solution. The results implied that the main adsorption mechanism was the replacement of surface hydroxyl groups by phosphate via the formation of inner-sphere complex. The adsorption process was characterized by chemical adsorption onto WLGIOWHP. The non-electrostatic model (NEM) was used to simulate the surface adsorption of phosphate onto WLGIOWHP. The total surface site density and protonation constants for NEM (N(T)=1.6×10(-4) mol/g, K(a1)=2.2×10(-4), K(a2)=6.82×10(-9)) were obtained by non-linear data fitting of acid-base titrations. In addition, the NEM was used to establish the surface adsorption complexation modeling of phosphate onto WLGIOWHP. The model successfully predicted the adsorption of phosphate onto WLGIOWHP from municipal wastewater. Copyright © 2014 Elsevier Inc. All rights reserved.

Phase change of iron ore reduction process using EFB as reducing agent at 900-1200°C

Science.gov (United States)

Purwanto, H.; Salleh, H. M.; Rozhan, A. N.; Mohamad, A. S.; Zakiyuddin, A.

2018-04-01

Treatment of low grade iron ore involved reduction of oxygen in iron oxide by using reductant such as carbon monoxide or hydrogen gas. Presently, carboneous materials such as coke/coal are widely used as a source to provide reducing gas, but some problem arises from this material as the gas can harm the environments. Therefore, empty fruit bunch biomass from oil palm becomes an alternative to replace the usage of coke/coal as their major composition is carbon and hydrogen. The idea of replacing coke with biomass will reduce the amount of carbon dioxide release as biomass is a carbon neutral and renewable source, and at the same time abundance of waste from oil palm industries can be overcome. Therefore, the aim of this research is to upgrade the low grade iron with reducibility more than 50% being used in iron and steel making. In this research, low grade iron ore are mixed together with EFB then is making into composite pellet before being reduced at certain parameter chosen. The variables involved in this research is composition EFB (10%, 30% and 50%), temperature (1000°C, 1100°C and 1200°C) and reduction time is fixed with 30 minutes. From the experiment conducted, the highest reducibility achieved is 76.37% at temperature 1200°C. While XRD analysis shows the existence of metallic iron phase started to form at 1000°C with composition of 30% of EFB. Meanwhile, from magnetization test show that at 1200°C the highest magnetic susceptibility is achieved as the dominance phase at 1200°C is metallic phase. Therefore it is an interesting alternative to replace coke with biomass for reducing agent in upgrading low grade iron into workable ores.

DECODING OF ACADEMIC CONTENT BY THE 1st GRADE STUDENTS

Directory of Open Access Journals (Sweden)

Kamil Błaszczyński

2017-07-01

Full Text Available In the paper a comparative study conducted on the 1st grade students of sociology and pedagogy is discussed. The study was focused on the language skills of students. The most important skills tested were the abilities to decode academic content. The study shows that the students have very poor language skills in decoding the academic content on every level of its complexity. They also have noticeable problems with the definition of basic academic terms. The significance of the obtained results are high because of the innovative topic and character of the study, which was the first such study conducted on students of a Polish university. Results are also valuable for academic teachers who are interested in such problems as effective communication with students.

Treatment of an isolated high-grade, low-tonnage uranium orebody

International Nuclear Information System (INIS)

Ajuria-Garza, S.

1976-01-01

A completely integrated process leading to a commercial-grade uranium concentrate has been developed for the El Nopal orebody which contains 115000t of ore with an average grade of 0.283%, equivalent to 325t of U 3 O 8 . The process consists of crushing (from -12 in to -1.5in), heap leaching with recirculation, a special type of countercurrent washing (also in the heap), solvent extraction to give an exceptionally high uranium concentration, re-extraction, precipitation with ammonium hydroxide, filtration and calcining. The main factors that influence heap leaching are analysed in detail: heap geometry, crushed ore size distribution, base design and construction, method of heaping, acid feeding method, flow of liquors through the heap and washing procedures. Leaching efficiencies range from 80 to 85% and washing efficiencies from 96 to almost 100% with an overall extraction efficiency of 77 to 85%. Acid consumption is usually less than 25kg/t of ore. The leaching and washing processes described are designed to use an overall solid-to-liquid ratio of about 3:1 thus producing very concentrated liquors with a U 3 O 8 content of about 7g/l. These liquors are filtered and fed directly to a solvent extraction system using Alamine 336 (tri-capryl amine) and isodecanol in kerosene. The high feed concentration makes it possible to use a high concentration of amine. The organic solvent contains 120g/l of Alamine and 98g/l of isodecanol. Re-extraction can be with a saline solution containing 100g/lNH 4 Cl and 250g/l(NH 4 )SO 4 . The strong liquor obtained from re-extraction contains 70-75g/lU 3 O 8 . The remaining steps of precipitation, filtration and calcining can then follow general practice and lead to a product which meets currently accepted commercial specifications. As an alternative, nitrate re-extraction has been shown to produce a solution of about 70g/l which will feed directly to tributyl phosphate (TBP) refining without the necessity of ever producing a

Vanadium-bearing titaniferous iron ores from the Rooiwater, Usushwana, Mambula, Kaffirskraal, and the Trompsburg igneous complexes

International Nuclear Information System (INIS)

Reynolds, A.M.

1979-01-01

The mineralogy and chemistry of some vanadium-bearing titaniferous iron ores from a number of smaller South African basic intrusions are reported, and an assessment is given of the potential of these ores for use as raw materials in the production of iron, high-titania slag, and vanadium pentoxide. The ores from each complex can be distinguised readily on the basis of their chemical composition and textural relations. The Rooiwater Complex represents the most promising area. It contains two layers of titaniferous magnetite, each approximately 8 m thick, in the eastern part, the lowest seam being chemically similar to the economically important main layer of titaniferous magnetite in the Bushveld Complex. The ores are silicate-poor and consist largely of multi-phase titaniferous-magnetite grains containing modified ilmenite and pleonaste micro-intergrowths. The coarse grain size of these ores favours beneficiation, and they can be partially treated to yield ilmenite concentrates and low-titania magnetite fractions in which the content of vanadium pentoxide is higher than that in the original ores. The Mambula ores are silicate-rich and would require extensive beneficiation. The Kaffirskraal ores consist of multi-phase grains of titaniferous magnetite containing crystallographically oriented ilmenite, ulvospinel, and pleonaste micro-intergrowths. Minor coarser-grained ilmenite is also present. The Usushwana ores are texturaly similar but contain abundant lamellar ilmenite in place of the ulvospinel. The ores from these two complexes cannot be beneficiated by conventional ore-dressing techniques, and would require direct metallurgical treatment for the recovery of iron, titania, and vanadium pentoxide [af

Filtration aids in uranium ore processing

International Nuclear Information System (INIS)

Ford, H.L.; Levine, N.M.; Risdon, A.R.

1975-01-01

A process of improving the filtration efficiency and separation of uranium ore pulps obtained by carbonate leaching of uranium ore which comprises treating said ore pulps with an aqueous solution of hydroxyalkyl guar selected from the group consisting of hydroxyethyl and hydroxypropyl guar in the amount of 0.1 and 2.0 pounds of hydroxyalkyl guar per ton of uranium ore

Using apatite to discriminate synchronous ore-associated and barren granitoid rocks: A case study from the Edong metallogenic district, South China

Science.gov (United States)

Duan, Deng-Fei; Jiang, Shao-Yong

2018-06-01

In order to find criteria to discriminate the synchronous ore-associated and barren granitoid rocks, we have determined apatite chemistry associated with ore-associated (Cu-Au) and barren granitoid rocks in the Edong district of the Middle and Lower Yangtze River metallogenic belt, South China. Both rock types give zircon U-Pb ages between 135.0 and 138.7 Ma. Apatite has a higher volatile and Li content (Cl: 0.19-0.57 wt%, average 0.35 wt%, SO3: 0.08-0.71 wt%, average 0.32 wt%, Li: 0.49-7.99 ppm, average 3.23 ppm) in ore-associated rocks than those in barren rocks (Cl: 0.09-0.31 wt%, average 0.16 wt%, SO3: 0.06-0.28 wt%, average 0.16 wt%, Li: 0.15-0.89 ppm, average 0.36 ppm). Apatite (La/Yb)N ratios and Eu/Eu* values are relatively high and show wider variation in ore-associated rocks than those in barren rocks. Apatite (La/Sm)N and (Yb/Sm)N show positive correlation in ore-associated rocks but negative in barren rocks. The higher volatile content occurs in ore-associated magma, favoring Cu-Au transportation and deposition. Furthermore, amphibole fractional crystallization in ore-associated magma further enriched the ore elements in the residual melt. Barren rocks may have undergone fluid exsolution before emplacement, which makes it barren in Cl, S and ore elements (Cu, S). These signatures emphases the significance of volatile and magma evolution in mineralization and indicate that analyses of magmatic apatite can serve to distinguish ore-associated from barren intrusions.

Continuous radiometric control of P/sub 2/O/sub 5/ content in phosphorite ore pulp

Energy Technology Data Exchange (ETDEWEB)

Belyakov, M A; Terent' ev, E P; Khoruzhii, A I

1976-03-01

Procedures have been developed for a continuous radiometric determination of P/sub 2/O/sub 5/ (6 to 8%) in the pulp of phosphorite ore on the basis of correlation between U and P contents in phosphorites. The pulp is piped from the classifier of one of the sections of the enrichment plant into a vertical cylindrical container whose upper part carries, mounted in its centre, a scintillator with an 80 x 80 mm NaJ(TL) crystal a FEU-82 photoelectric device. Overflowing the container edge, the pulp accumulates in the bleeding pipe and is moved on to be floated. The measuring of the gamma radiation from the pulp (with an energy of about 0.2 MeV) and the recording of the readings are carried out with a single-channel gamma spectrometer of the SP-ZM type and a self-writing KSP-type potentiometer. The sensitivity of measurements is 70 imp./sec per 1% of P/sub 2/O/sub 5/ with a 70 imp./sec background. The mean-square discrepancy as compared with chemical data is 0.3% of P/sub 2/O/sub 5/.

Ore leaching processing for yellow cake production and assay of their uranium content by radiometric analysis

Energy Technology Data Exchange (ETDEWEB)

Abdel-Rahman, Mohamed A.E. [Nuclear Engineering Department, Military Technical College, Kobry El-Kobbah, Cairo (Egypt); El-Mongy, Sayed A. [Nuclear and Radiological Regularity Authority (ENRRA), Nasr City, Cairo (Egypt)

2018-01-17

In this study, Ore granite samples were collected from Gattar site for leashing of yellow cake. The process involves heap leaching of uranium through four main steps; size reduction, leaching, uranium purification, and finally precipitation and filtration. The separation process has been given in details and as flow chart. Gamma spectrometry based on HpGe detector and energy dispersive X-ray (EDX) were used to assay uranium content and activity before and after separation. The uranium weight percentage value as measured by EDX were found to be 40.5 and 67.5 % before and after purification respectively. The results of the calculations based on gamma measurements show high uranium activity and the uranium activity ratios values are 0.045 ± 4.9, 0.043 ± 4.7, and 0.046 ± 2.3 %, before purification, whereas these values were found to be 0.050 ± 3.3, 0.049 ± 3.3, and 0.050 ± 2.7 %, after purification, respectively. The results are discussed in details in the paper. (copyright 2018 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Difference of ore-bearing and non-ore-bearing pegmatite in the Guangshigou area and its research significance

International Nuclear Information System (INIS)

Zuo Wenqian; Zhang Zhanshi; Sha Yazhou; Rao Chaojun

2011-01-01

Guangshigou uranium deposit is one of the typical granite-pegmatite uranium deposits in China, the ore-body are located in the density zone of the outside contact zone of granite pluton. To distinguish the ore-bearing and Non-ore-bearing pegmatite is one of the most practices and have great significance for the effect of mineral exploration. Based on the field investigation and former research results, contrast research on the characteristics of the pegmatite on petrology, geophysical, geochemistry and stable isotopes have been carried out. It is pointed out that the ore-bearing pegmatite differ from the non-ore-bearing one from macro-and-micro-view in Guangshigou Uranium deposits, the main characteristics are summarized; the macro-and-micro signs are established, the genetic difference between the ore-bearing and non-ore-bearing pegmatite are discussed primarily. The achievements would be helpful for prospecting and researching of this type uranium deposits in China. (authors)

Influence of acid/ore relation in the uranium-silicate ore treatment

International Nuclear Information System (INIS)

Antaki, C.; Cipriani, M.; Bruno, J.B.

1985-01-01

The estimation of acid addition effect (Kg of H 2 SO 4 /t of ore) in uranium extraction from an uranium-silicate ore, with a view to the control of silica concentration in leach under 0,6 g/l is presented. The analysis was effected based on bench-scale tests, with different quantities of sulfuric acid addition. (Author) [pt

Studies on uranium ore processing

International Nuclear Information System (INIS)

Suh, I.S.; Chun, J.K.; Park, S.W.; Choi, S.J.; Lee, C.H.; Chung, M.K.; Lim, J.K.

1983-01-01

For the exploitation of domestic uranium ore deposit, comprehensive studies on uranium ore processing of the Geum-San pit ore are carried out. Physical and chemical characteristics of the Geum-San ore are similar to those of Goe-San ore and the physical beneficiation could not be applicable. Optimum operating conditions such as uranium leaching, solid-liquid separation, solvent extraction and precipitation of yellow cake are found out and the results are confirmed by the continous operation of the micro-plant with the capacity of 50Kg, ore/day. In order to improve the process of ore milling pilot plant installed recently, the feasibility of raffinate-recycle and the precipitation methods of yellow cake are intensively examined. It was suggested that the raffinate-recycle in the leaching of filtering stage could be reduced the environmental contamination and the peroxide precipitation technique was applicable to improve the purity of yellow cake. The mechanism and conditions the third phase formation are thoroughly studied and confirmed by chemical analysis of the third phase actually formed during the operation of pilot plant. The major constituents of the third phase are polyanions such as PMosub(12)Osub(40)sup(3-) or SiMosub(12)Osub(40)sup(4-). And the formation of these polyanions could be reduced by the control of redox potential and the addition of modifier. (Author)

Neutron shielding properties of boron-containing ore and epoxy composites

International Nuclear Information System (INIS)

Li Zhifu; Xue Xiangxin

2011-01-01

Using the boron-containing iron ore concentrate and boron-rich slag as studying object, the starting materials were got after the specific green ore containing boron dressing in China and blast furnace separation respectively. Monte-Carlo method was used to study the effect of the boron-containing iron ore concentrate and boron-rich slag and their composites with epoxy on the neutron shielding abilities. The reasons that affecting the shielding materials properties was discussed and the suitable proportioning of boron-containing ore to epoxy composites was confirmed; the 14.1 MeV fast neutron removal cross section and the total thermal neutron attenuation coefficient were obtained and compared with that of the common used concrete. The results show that the shielding property of 14.1 MeV fast neutron is mainly concerned with the low-Z elements in the shielding materials, the thermal neutron shielding ability is mainly concerned with boron concentrate in the composite, the attenuation of the accompany γ-ray photon is mainly concerned with the high atom number elements content in the ore and the density of the shielding material. The optimum Janume fractions of composites are in the range of 0.4-0.6 and the fast neutron shielding properties are similar to concrete while the thermal neutron shielding properties are higher than concrete. The composites are expected to be used as biological concrete shields crack injection and filling of the anomalous holes through the concrete shields around the radiation fields or directly to be prepared as shielding materials.(authors)

The Compatibility of Developed Mathematics Textbooks' Content in Saudi Arabia (Grades 6-8) with NCTM Standards

Science.gov (United States)

Alshehri, Mohammed Ali; Ali, Hassan Shawki

2016-01-01

This study aimed to investigate the compatibility of developed mathematics textbooks' content (grades 6-8) in Saudi Arabia with NCTM standards in the areas of: number and operations, algebra, geometry, measurement, data analysis and probability. To achieve that goal, a list of (NCTM) standards for grades (6-8) were translated to Arabic language,…

Bioleaching of UO22+ ions from poor uranium ores by means of cyanobacteria

International Nuclear Information System (INIS)

Cecal, A.; Humelnicu, D.; Popa, K.; Palamaru, I.; Nemtoi, G.; Rudic, V.; Gulea, A.

2000-01-01

Uranium (VI) leaching, as uranyl ions, from ores with a poor content in util minerals, using some algae as: Porphyridium cruentum (Smith and Soerly) Naegeli, Spirulina platensis CNM-CB-02 and Nostoc linkia (Roth) Born and Flah was studied. The basic composition of these ores allowed the self-maintenance and self-development of these microorganisms, which have facilitated then the leaching of the uranium (VI) as UO 2 2+ ions. The microbial leaching degree was comprised between 40-90%, depending on the used alga and experimental conditions. (author)

Underground leaching - A method for the economic extraction of uranium from low-grade ores; Podzemnoe vyshchelachivanie - sposob ehkonomicheskogo izvlecheniya urana iz bednykh rud

Energy Technology Data Exchange (ETDEWEB)

Zefirov, A P [Gosudarstvennyj Komitet po Ispol' zovaniyu Atomnoj EHnergii SSSR, Moskva, Union of Soviet Socialist Republics (Russian Federation)

1967-06-15

The method of underground leaching of uranium ores has a number of advantages over extraction followed by processing of the ores in factories. It has been studied in two types of deposit, occurring in rock masses and sandy shales. Research techniques were worked out accordingly for the leaching of uranium from large-grained ore (-200 mm) and from layers in natural stratification. Special models were constructed permitting the simulation of underground leaching conditions. The results obtained were checked in field conditions on experimental plots and experimental underground blocks. The investigations demonstrated the practicability of the process of underground leaching of uranium from certain ores and made it possible to work out flow-sheets and routines for an industrial process, information about which is given in the paper. (author)

Nickel Ore Dispersion Evaluation and Consequences in Flotation Process

Science.gov (United States)

de São José, Fábio; Imbelloni, Alaine Moreira; Nogueira, Francielle Câmara; Pereira, Carlos Alberto

2016-04-01

Nickel ore dispersion before flotation using different reagents was investigated on a bench scale to improve metallurgical recovery and selectivity. The nickel ore had a content of 0.8 pct nickel and 14.5 pct MgO. A positive linear correlation between MgO and Ni was found. Carboxy methyl cellulose, both pure and combined with Na2CO3, was the best dispersant used. The most efficient collector was potassium amyl xanthate combined with mercaptobenzothiazole, and the addition of xanthate was decisive for this good result because it is normally more stable in the pH range used in the tests. A pH change from 7 to 9 resulted in a metal recovery increase of 49.3 pct, together with an increase of 6.25 pct of MgO in the concentrate.

Characterization and Separation Studies of a Fine Sedimentary Phosphate Ore Slime

Directory of Open Access Journals (Sweden)

Xin Liu

2017-06-01

Full Text Available Detailed characterization and recovery of apatite from a sedimentary phosphate ore slime of a gravity plant of Yichang, China, were investigated. The phosphate ore slime consisted mainly of apatite, quartz, dolomite, and clay. To start with, the ore slime was characterized in sufficient detail to reveal that it is extremely fine in distribution with a d50 of 65 μm. Other different characterizations, such as apatite grain size distribution, apatite liberation, particle density distribution, and theoretical grade recovery, were also analyzed by mineral liberation analyser (MLA. Based on the results, a new gravity-flotation process, which was comprised of spiral gravity and reverse flotation, was proposed to process the slime. In the new process, the apatite was firstly recovered by two-stage spiral gravity, avoiding direct flotation. The gravity concentrate was the feed for the reverse flotation. A phosphate concentrate of 30.51% P2O5 with a P2O5 recovery of 89.00% can be produced from the slime analyzing 24.25% P2O5. Compared to the conventional direct-reverse flotation process, it was found that the reagent cost of the new gravity-flotation process was lower a quarter than that of the direct-reverse flotation flowsheet.

The effect of iron-ore particles on the metal content of the brown alga Padina gymnospora (Espirito Santo Bay, Brazil)

International Nuclear Information System (INIS)

Nassar, C.A.G.; Salgado, L.T.; Yoneshigue-Valentin, Y.; Amado Filho, G.M.

2003-01-01

Iron ore deposits mat be the source of metals found in the brown alga Padina gymnospora. - The iron-ore particles discharged by a pellet processing plant (Espirito Santo Bay, Brazil) cover the seabed of Camburi Beach and consequently, the epibenthic community. In order to determine the importance of the contribution of the iron-ore deposits to the metal concentration in macroalgae of Espirito Santo Bay, four methods of cleaning particulate material adhered to the surface of thalli were tested prior to metal tissue analysis (Al, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) of Padina gymnospora. In addition, heavy metal concentrations were determined in individuals of P. gymnospora from a site (Frade Island) not affected by the iron-ore particles. The most efficient cleaning treatment, a combination of scraping and washing with an ethanol-seawater solution (NA+SC+ET) removed a number of particles on the surface of thalli 10 times higher than that observed in the control (C). Using this treatment, the total-metal concentrations were reduced by 78% for Fe and 50% for Al respect to the control. However, Fe, Al and Cu concentrations after treatment NA+SC+ET were significantly higher than those found at Frade Island. It is suggested that the iron-ore deposit might be a source for metal availability to macroalgae exposed to the dumped material at Espirito Santo Bay

The seat of ground water discharge as ore-mabilizing factor in the formatian of hydrogenic uranium deposits

International Nuclear Information System (INIS)

Natal'chenko, B.I.; Gol'dshtejn, R.I.

1982-01-01

The role of structural-hydrogeological factor in the process of ore-controlling zoning development during hydrogeneous deposit formation is discussed, as reflecting in the most objective way the spreading of stratal oxidation zones and morphology of uranium mineralization as regards discharge seats because there are only they which mobilize stratal waters for active displacement. The types of discharge seats of stratal waters and their effect on formation of ore-controlling zones of stratal oxidation with uranium mineralization are presented. The conclusion is drawn that local and regional discharge seats of stratal waters dictate both the spacing of regional fronts of stratal-oxidized rocks and their ore content degree. The displacement of discharge seats or their growing into local regions of alimentation results in reorganization of the total ore-controlling zoning, which enables to consider the seats of water discharge as ore-mobilizing structures in the formation of hydrogenic uranium deposits

Direct Reduction of Iron Ore

Science.gov (United States)

Small, M.

1981-04-01

In the search for a pure, available iron source, steelmakers are focusing their attention on Directly Reduced Iron (DRI). This material is produced by the reaction of a low gangue iron ore with a hydrocarbonaceous substance. Commercially, DRI is generated in four different reactors: shaft (moving-bed), rotary kiln, fluidized bed, and retort (fixed-bed). Annual worldwide production capacity approaches 33 million metric tons. Detailed assessments have been made of the uses of DRI, especially as a substitute for scrap in electric furnace (EF) steelmaking. DRI is generally of a quality superior to current grades of scrap, with steels produced more efficiently in the EF and containing lower levels of impurities. However, present economics favor EF steel production with scrap. But this situation could change within this decade because of a developing scarcity of good quality scrap.

New age radiometric ore sorting - the elegant solution

International Nuclear Information System (INIS)

Gordon, H.P.; Heuer, T.

2000-01-01

Radiometric ore sorting technology and application are described in two parts. Part I reviews the history of radiometric sorting in the minerals industry and describes the latest developments in radiometric sorting technology. Part II describes the history, feasibility study and approach used in the application of the new technology at Rossing Uranium Limited. There has been little progress in the field of radiometric sorting since the late 1970s. This has changed with the development of a high capacity radiometric sorter designed to operate on low-grade ore in the +75mm / -300mm size fraction. This has been designed specifically for an application at Rossing. Rossing has a long history in radiometric sorting dating back to 1968 when initial tests were conducted on the Rossing prospect. Past feasibility studies concluded that radiometric sorting would not conclusively reduce the unit cost of production unless sorting was used to increase production levels. The current feasibility study shows that the application of new radiometric sorter technology makes sorting viable without increasing production, and significantly more attractive with increased production. A pilot approach to confirm sorter performance is described. (author)

Geochemical features of the ore-bearing medium in uranium deposits in the Khiagda ore field

Science.gov (United States)

Kochkin, B. T.; Solodov, I. N.; Ganina, N. I.; Rekun, M. L.; Tarasov, N. N.; Shugina, G. A.; Shulik, L. S.

2017-09-01

The Neogene uranium deposits of the Khiagda ore field (KOF) belong to the paleovalley variety of the hydrogene type and differ from other deposits of this genetic type in the geological and geochemical localization conditions. The contemporary hydrogeochemical setting and microbiological composition of ore-bearing medium are discussed. The redox potential of the medium (Eh is as low as-400 mV) is much lower than those established at other hydrogenic deposits, both ancient Late Mesozoic and young Late Alpine, studied with the same methods in Russia, Uzbekistan, and southern Kazakhstan. The pH of subsurface water (6.86-8.13) differs in significant fluctuations both between neighboring deposits and within individual ore lodes. Hydrogen-forming and denitrifying bacteria are predominant in microbiological populations, whereas sulfate-reducing bacteria are low-active. The consideration of these factors allowed us to describe the mechanism of uranium ore conservation as resulting from the development of the cryolithic zone, which isolates ore lodes from the effect of the external medium. Carbonated water supplied from the basement along fault zones also participates in the formation of the present-day hydrogeochemical setting. Based on the features of the ore-bearing medium, we propose a method of borehole in situ acid leaching to increase the efficiency of mining in the Khiagda ore field.

Silver content determination in mining and ore dressing using radionuclide-excited X-ray fluorescence analysis

International Nuclear Information System (INIS)

Koerner, B.; George, R.; Ratnikow, W.

1989-01-01

A laborsaving method based on radionuclide-excited X-ray fluorescence is described for the determination of silver in mining and ore dressing. Detection limits reached under operation conditions and measuring errors are discussed and compared with results from chemical analyses

Nuclear forensic analysis of an unknown uranium ore concentrate sample seized in a criminal investigation in Australia

International Nuclear Information System (INIS)

Keegan, Elizabeth; Kristo, Michael J.; Colella, Michael; Robel, Martin; Williams, Ross; Lindvall, Rachel; Eppich, Gary; Roberts, Sarah; Borg, Lars; Gaffney, Amy; Plaue, Jonathan; Wong, Henri; Davis, Joel; Loi, Elaine; Reinhard, Mark; Hutcheon, Ian

2014-01-01

In early 2009, a state policing agency raided a clandestine drug laboratory in a suburb of a major city in Australia. While searching the laboratory, they discovered a small glass jar labelled 'Gamma Source' and containing a green powder. The powder was radioactive. This paper documents the detailed nuclear forensic analysis undertaken to characterize and identify the material and determine its provenance. Isotopic and impurity content, phase composition, microstructure and other characteristics were measured on the seized sample, and the results were compared with similar material obtained from the suspected source (ore and ore concentrate material). While an extensive range of parameters were measured, the key 'nuclear forensic signatures' used to identify the material were the U isotopic composition, Pb and Sr isotope ratios, and the rare earth element pattern. These measurements, in combination with statistical analysis of the elemental and isotopic content of the material against a database of uranium ore concentrates sourced from mines located worldwide, led to the conclusion that the seized material (a uranium ore concentrate of natural isotopic abundance) most likely originated from Mary Kathleen, a former Australian uranium mine

In situ carbonate leaching and recovery of uranium from ore deposits

International Nuclear Information System (INIS)

Hunkin, G.G.; Fife, T.P.; Stano, J.R.

1979-01-01

Uranium is leached from redox roll ore deposits by selective in-situ leaching with a solution of pH 7.4 to 9 (preferably 7.5 to 8.5) containing from about 0.5 to 5g/l of NH 4 HCO 3 and from about 0.1 to 3g/l of peroxide (preferably aqueous H 2 O 2 ), and sufficient NH 3 to maintain the desired pH. The leach solution is then withdrawn from the ore deposit and contacted with a strong base anion exchange material to strip the uranium from the leach solution. The uranium is eluted from the anion exchange material by an aqueous eluant, and the uranium is recovered from the eluate by first acidifying it and then treating it with ammonia to produce a precipitate of relatively pure ammonium diuranate. The content of the three components in the stripped leach solution is adjusted, and then the leach solution is recirculated through the ore deposit. After the uranium ore is removed to the extent economically practicable, the leach solution is replaced with an aqueous reducing solution which when passed into the ore deposit precipitates and renders insoluble any uranium and elements such as vanadium, molybdenum, and selenium. This process produces above ground a very low volume of impurities and waste solutions requiring disposal and does not cause material contamination of the underground deposit or any aquifer associated with the deposit

Examining longitudinal train dynamics in ore car tipplers

Science.gov (United States)

Cole, Colin; Spiryagin, Maksym; Bosomworth, Chris

2017-04-01

Train simulation has been adapted in this paper to model the behaviour of indexing operations in ore car tippler operations. An important consideration in simulations at these low speeds (less than 4 km/h) is the increased rolling resistance transitioning from stationary conditions to motion. Most formulations of rolling resistance equations do not include this range although there are empirical values in some railway standards. The indexer control utilised here has a target trapezoidal velocity profile. The indexer to train connection was modelled as a stiff linear spring, a damper and a gap element. A sensitivity analysis was completed considering variations in wagon connections including wedge static friction, preload, coupling slack and tippler slack. Track topography including downhill grades of 0.1% and 0.2% and a valley profile were also investigated. Results showed high sensitivity to draft gear parameters of static friction and preload, but minimal benefit from downhill grades and changes in coupling slack.

Emerging industrial processes for low grade rare earth mineral concentrates

International Nuclear Information System (INIS)

Soldenhoff, Karin; Ho, Elizabeth

2015-01-01

Historically rare earth recovery has mainly been derived from the processing of monazite, bastnasite and xenotime containing ores amenable to beneficiation, yielding high grade mineral concentrates. A notable exception is the recovery of heavy rare earths from ionic clays in Southern China. Recently, projects are being proposed to treat a range of mineral concentrates which tend to be lower grade with wide ranging modal mineralogy for rare earths and associated gangue minerals. This has a significant impact on processing routes. This paper discusses processes proposed for emerging rare earth producers and how different projects have responded to particular challenges including: Control of phosphorous due to the presence of xenotime or monazite type minerals; Control of phosphorous due to the presence of rare earth containing apatite; Rare earth recovery from polymetallic ores; Control of radionuclides in rare earth processing, etc.

Ore loses and dilution of the ore vein no. 4 in the Zletovo mine, Republic of Macedonia

Directory of Open Access Journals (Sweden)

Bogatinovski Nikola L.

2017-01-01

Full Text Available Zletovo mines have a tradition of exploration and exploitation of vein lead-zinc ores for almost a century. Ore losses and dilutions have always been imperative in production since traditional old methods of mining and low-productivity mineralization are used. In conditions of classical and sub-level method excavations used, the calculated ore losses in ore vein No. 4 are 13.5%, while at the level of all excavations in the Zletovo mines dilution averages at 10%. Ore dilution is also an important technical parameter and several possible variants were calculated. When analyzing the dilution that occurs during the preparation of the sub-level corridor with parameters such: different drop angle (45-60o, constant thickness of 1.47 m as the average vein thickness in the calculated ore reserves, width of the sub-level corridor of 1.57 m or to the width of the ore vein No. 4 were added 10 cm (left and right to 5 cm as much as is taken in the calculation of the planned dilution and height of 2.5 m as suggested for this mining method, it can be noticed that the planned dilution during this method of mining ranges from 26.3% to 42.3%. In conditions of use of this underground method of excavation, parameters are selected that allow for the indicated lowering of the dilution. Namely, the thickness of the ore wire would be 1.47 m, the mining width would be 1.57 m, only 10 cm (left and right up to 5cm to the thickness of the ore vein will be added, the height difference between the consecutive levels would be 7.5 m, dip angle of 45 to 60°, and with the excavation the whole ore vein would be covered in height. On the basis of these parameters, models were prepared in which the ore vein would have a different dip angle, from which the values for the planned ore dilution ranged from 6.7 to 7.8%, which is significantly lower than the average dilution in the Zletovo Mine.

Separation of substandard tin ores by x-ray fluorescence method

International Nuclear Information System (INIS)

Kotler, N.I.; Konovalov, V.M.; Kamenskij, Yu.V.; Neverov, A.D.; Ogorodnikov, Yu.V.

1987-01-01

Analysis of pure tin ores on X-ray fluorescence separation (XFS) is carried out. The volumes of lump sampling are substantiated; several variants of technical and economical efficiency of XFS application have been calculated. It is shown that at XFS of -400+25 mm classes conditional as to tin content intermediate product with high efficiency factor may be prepared. Separation of -25+10 mm class is unsuitable, as it doesn't allow to increase tin content to conditional, and the process efficiency is low

World production and possible recovery of cobalt from the Kupferschiefer stratiform copper ore

Directory of Open Access Journals (Sweden)

Pazik Paulina M.

2016-01-01

Full Text Available Cobalt is recognized as a strategic metal and also E-tech element, which is crucial for worlds development. An increasing demand for cobalt forces for searching of new resources that could be explored in European countries. There are many examples of cobalt recoveries, mostly from laterite and sulphide deposits. However, the accurate choice of the technology depends on many factors. The Kupferschiefer stratiform copper ore located in Poland is the biggest deposit of cobalt in Europe. Although KGHM Polska Miedz S.A. recovers many precious metals from this ore, cobalt is not recovered yet. This metal occurs as an accompanying element, mostly in the form of cobaltite (CaAsS, with the average content of 50–80 g/Mg. In this paper a possible recovery of cobalt from the Kupferschiefer ore, with the use of hydrometallurgical methods, was investigated.

Present and future: heap leaching of uranium ore in China

International Nuclear Information System (INIS)

Li Jianhua

2010-01-01

Based on small and disperse uranium deposits, and low grade ores, heap leaching has been developed as the dominating technique in the uranium production of China. It is indicated that heap leaching technique has such advantages as less capital, low cost, low power consumption and water consumption. At the meanwhile, heap leaching technique presents shortcomings of poor adaptability and low recovery rate. In order to meet the oncoming enormous demand of nuclear power, great effort shall be put on research of new technology, new equipment, new material. (authors)

Spectrophotometric determination of trace uranium in phosphate ore samples from kurum and uro areas, Nuba mountains, Sudan

International Nuclear Information System (INIS)

Mohamed, A. A.; Ali, A. H.; Altayeb, M. A. H.

2004-01-01

A method was proposed for the spectrophotometric determination of uranium content in phosphate ores. the method is based on the use of nitrogen (v) acid for leaching the rock, and treatment with ammonium carbonate solution, whereby uranium (Vi) is kept in solution as its carbonate complex. The ion-exchange technique was used for the recovery of uranium. Uranium was determined spectrophotometrically by measurement of the absorbance of the yellow uranium (Vi)-8-hydroxyquinolate complex at λ 425 nm. The procedure was used for the determination of trace uranium content in 30 phosphate ore samples collected from Kurun and Uro areas in Nuba mountains in Sudan. X-ray fluorescence technique was employed for the assessment of the method used. The spectrophotometric method results show a high similarity with those obtained by XRF technique. This agreement indicates that the procedure proposed here has been successfully applied for the determination of uranium in phosphate ores. (Author)

Ambient Temperature Flotation of Sedimentary Phosphate Ore Using Cottonseed Oil as a Collector

Directory of Open Access Journals (Sweden)

Yaoyang Ruan

2017-04-01

Full Text Available The mid-low grade sedimentary phosphate ore, abundant in silicate and carbonate gangue minerals, exhibits a poor processability. It is conventionally enriched using high temperature flotation to remove silicate gangues with fatty acid as a collector. Cottonseed oil has been proved to be an efficient collector for achieving ambient temperature flotation of the sedimentary phosphate ore used in this study. Flotation kinetics was investigated to ascertain the excellent collecting performance of cottonseed oil, as compared with oleic acid, and the phosphate flotation fitted well with the first-order flotation model. Based on the analysis of flotation reagent effect on the direct flotation process using the response surface methodology (RSM, a closed circuit of direct-reverse flotation for stepwise removing silicate and carbonate gangues from the sedimentary phosphate ore was established. Consequently, a required high quality of phosphate concentrate containing 30.16% P2O5 was obtained, with a recovery of 90.90%. Scanning electron microscopy (SEM and X-ray diffraction analysis (XRD of the flotation products confirmed that the majority of silicate and carbonate gangues were effectively removed from the concentrate products.

Uranium ore processing in Spain

International Nuclear Information System (INIS)

Josa, J.M.

1976-01-01

The paper presents a review of the Spanish needs of uranium concentrates and uranium ore processing technology and trends in Spain. Spain produces approximately 200t U 3 O 8 /a at two facilities. One plant in the south (Andujar, Jaen) can obtain 70t U 3 O 8 /a and uses a conventional acid leaching process with countercurrent solvent extraction. A second plant, situated in the west (Ciudad Rodrigo, Salamanca) has started in 1975 and has a capacity of 120-130t U 3 O 8 /a, using acid heap leaching and solvent extraction. There is another experimental facility (Don Benito, Badajoz) scheduled to start in 1976 and expected to produce about 25-35t U 3 O 8 /a as a by-product of the research work. For the near future (1978) it is hoped to increase the production with: (a) A new conventional acid leaching/solvent extraction plant in Ciudad Rodrigo; its tentative capacity is fixed at 550t U 3 O 8 /a. (b) A facility in the south, to recover about 130t U 3 O 8 /a from phosphoric acid. (c) Several small mobile plants (30t U 3 O 8 /a per plant); these will be placed near small and isolated mines. The next production increase (1979-1980) will come with the treatment of sandstones (Guadalajara and Cataluna) and lignites(Cataluna); this is being studied. There are also research programmes to study the recovery of uranium from low-grade ores (heap, in-situ and bacterial leaching) and from other industries. (author)

Electron microscopy and microanalysis of uranium phases in primary ores, Eocene and Miocene of south Texas

International Nuclear Information System (INIS)

Liang, L.C.; Price, J.G.; Bobeck, P.

1984-01-01

Two contrasting types of roll-front uranium deposits occur in south Texas. In the barrier-bar sands of the Eocene Jackson Group, organic matter was essential to uranium reduction, whereas in the fluvial sands of the Miocene Oakville Formation, epigenetic pyrite was the reductant. In a sample of reduced Oakville ore, a uranium phase with grains ranging in diameter from < 1 to 20μm was recognized by SEM backscattered-electron imaging and wavelength-dispersive spectrometer (WDS) elemental-dot mapping. Quantitative microprobe analyses indicated that the phase is a uranium-calcium silicate-phosphate with molar Ca/P approximately equal to 1.0, U/P equal to 2.8 +/- 0.4 (n = 27), and U/Si approaching 1.0 in samples uncontaminated with quartz, feldspar, or clay minerals. Highest uranium content is 59%. Oakville ore is typically easy to leach by in-situ methods. Jackson ore contains 2 uranium phases. Sulfur-rich organic matter contains 4.1 +/- 1.6% uranium (n = 27). Although individual grains of a possible uranium mineral within the organic matter are too small to be resolved by electron imaging, a consistent molar U/Fe (0.5 +/- 0.1) suggests a uranium-iron oxide phase. Alternatively, uranium is adsorbed by or otherwise bound to the organic matter. The second phase is a uranium-calcium silicate-phosphate that differs from the Oakville ore. Molar Ca/P equals 0.8 +/- 0.2 (n = 13), and U/P equals 4.7 +/- 0.4. Small grain size (generally less than 1 μm) prevented analysis of samples uncontaminated with quartz and pyrite. The grain with highest uranium content (43%) has U/Si equal to 0.34. Jackson ore is less favorable for in-situ leaching than Oakville ore in part because the organic-associated uranium is difficult to extract

Bioleaching of low grade uranium ore containing pyrite using A. ferrooxidans and A. thiooxidans

International Nuclear Information System (INIS)

Alexey Borisovich Umanskii; Anton Mihaylovich Klyushnikov

2013-01-01

A process of uranium extraction from ore containing 3.1 % pyrite by bacterial leaching was investigated in shaken flasks during 90 days. The highest uranium recovery amounting to 85.1 % was obtained using binary mixture of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans that was exceeding results obtained by traditional acid leaching technique up to 27 %. High uranium recovery was founded to be due to the high degree of pyrite dissolution that can be readily achieved by bacterial leaching (up to 98.0 %). (author)

Microbial reduction of iron ore

Science.gov (United States)

Hoffmann, M.R.; Arnold, R.G.; Stephanopoulos, G.

1989-11-14

A process is provided for reducing iron ore by treatment with microorganisms which comprises forming an aqueous mixture of iron ore, microorganisms operable for reducing the ferric iron of the iron ore to ferrous iron, and a substrate operable as an energy source for the microbial reduction; and maintaining the aqueous mixture for a period of time and under conditions operable to effect the reduction of the ore. Preferably the microorganism is Pseudomonas sp. 200 and the reduction conducted anaerobically with a domestic wastewater as the substrate. An aqueous solution containing soluble ferrous iron can be separated from the reacted mixture, treated with a base to precipitate ferrous hydroxide which can then be recovered as a concentrated slurry. 11 figs.

Sinterization of manganese ore tailings under natural air

Energy Technology Data Exchange (ETDEWEB)

Lima, M.M.F.; Souza, L.G.P.R.M.F. [Universidade Federal de Ouro Preto (UFOP), MG (Brazil)

2014-07-01

The manganese ore has wide application in metallurgy. However, from each of three hundred concentrations found, only one can be seen as a deposit. The aim of this study was to obtain and characterize a sinter from manganese ore tailing. The tailing was milled, classified (<400 ⧣) and calcinated (800°C - 3600s). The mixture had 12% moisture, 7 and 9% of activated charcoal. After homogenization, the sintering were carried out at 1140, 1145 and 1150°C during 1800, 7200 and 14400s at natural air. The sintered products were characterized by EDS analysis, BET surface area, apparent density, X-rays diffraction and SEM/EDS. The mass loss was approximately 14% and 16% in the calcination and sintering, respectively, due to the elimination of volatile products and water. The main phases characterized: SiO2, silicate with high content of manganese in the matrix and other silicates with different proportions of Ti, Na, Mn, Mg and Ca. (author)

A procedure for oxidation during the acid leaching of non-ferrous ores, particularly uranium ores

International Nuclear Information System (INIS)

Zubcek, L.; Baloun, S.; Martinek, K.; Vebr, Z.; Krepelka, J.; Lasica, S.

1989-01-01

It is suggested that dust from the production of ferroalloys of manganese, particularly ferrosilicomanganese and ferromanganese, can be conveniently used for oxidation during the acid leaching of non-ferrous ores, particularly uranium ores. This dust contains 30 to 40% oxides of manganese, about one-half of this is MnO 2 . Iron in the dust is present in the trivalent form, and the dust is pefectly dry. The conventional grinding of oxidants for the ore processing is eliminated, the dust being available in particle size below 0.2 mm. The dust is added in amounts of 5 to 100 kg per ton of the ore, and the suspension is typically heated at 115 degC for 3.5 hr. (P.A.)

Effects of iron content on microstructure and crevice corrosion of titanium Grade-2

International Nuclear Information System (INIS)

He, X.; Noel, J.J.; Shoesmith, D.W.

2003-01-01

The effects of iron content on microstructure and crevice corrosion of titanium Grade-2 (Ti-2) were studied using a galvanic coupling technique combined with optical microscopy and secondary ion mass spectrometry (SIMS) imaging. The study reveals that iron content has a significant effect on the microstructure and crevice corrosion behavior of Ti-2. The grain size decreases significantly with the increasing iron content. For Ti-2 material of medium iron content, crevice corrosion was readily initiated and exhibited extensive intergranular attack which could be associated with the more reactive iron-stabilized β-phase within the α-phase matrix as revealed by SIMS imaging. By contrast, Ti-2 materials with low and high iron content showed suppressed crevice attack. The small surface area of available grain boundaries in Ti-2 of low iron content accounted for this limited attack. For the material with high iron content, SIMS imaging suggest that some Ti x Fe intermetallic particles were formed. These particles may act as proton reduction catalysts and enhance crevice corrosion resistance. (author)

Steady-state optimization of ore-dressing plants

International Nuclear Information System (INIS)

Niemi, A.J.

1989-01-01

The ore-dressing plant consists of the steps of grinding and flotation. Its optimization is based on steady state simulation of the mass balances with a plant model. The model data are obtained by tracer tests and analysis. An evaluation of performance of the plant has to observe the recovery of the valuable mineral, the throughput of the system and the grade of the concentrate which are outputs of the flotation plant. Simulation with the flotation plant model yields that combination of values of controllable inputs to flotation which corresponds to an optimal operation of the conditioning an flotation system, for a specified feed and its fractional composition. Simulations for other feeds and compositions advise how they should be chosen, for a better overall performance. (author)

Complexing and hydrothermal ore deposition

CERN Document Server

Helgeson, Harold C

1964-01-01

Complexing and Hydrothermal Ore Deposition provides a synthesis of fact, theory, and interpretative speculation on hydrothermal ore-forming solutions. This book summarizes information and theory of the internal chemistry of aqueous electrolyte solutions accumulated in previous years. The scope of the discussion is limited to those aspects of particular interest to the geologist working on the problem of hydrothermal ore genesis. Wherever feasible, fundamental principles are reviewed. Portions of this text are devoted to calculations of specific hydrothermal equilibriums in multicompone

Ore-forming environment and ore-forming system of carbonaceous-siliceous-pelitic rock type uranium deposit in China

International Nuclear Information System (INIS)

Qi Fucheng; Zhang Zilong; Li Zhixing; He Zhongbo; Wang Wenquan

2012-01-01

It is proposed that there are four types of ore-forming systems about carbonaceous-siliceous-pelitic rock type uranium deposit in China based on systematic study on structural environment and distribution regularity of uraniferous construction of marine carbonaceous-siliceous-pelitic rock in China: continental margin rift valley ore-forming systems, continental margin rifting deep fracture zone ore-forming systems, landmass boundary borderland basin ore-forming systems and epicontinental mobile belt downfaulted aulacogen ore-forming systems. It is propounded definitely that it is controlled by margin rift valley ore-forming systems and continental margin rifting deep fracture zone ore-forming systems for large-scale uranium mineralization of carbonaceous-siliceous-pelitic rock type uranium deposit in China, which is also controlled by uraniferous marine carbonaceous-siliceous-pelitic rock construction made up of silicalite, siliceous phosphorite and carbonaceous-siliceous-pelitic rock, which settled down accompany with submarine backwash and sub marine volcanic eruption in margin rift valley and continental margin rifting mineralizing environment. Continental mar gin rift valley and continental margin rifting thermal sedimentation or exhalation sedimentation is the mechanism of forming large-scale uraniferous marine carbonaceous-siliceous-pelitic rock construction Early Palaeozoic Era in China or large-scale uranium-polymetallic mineralization. (authors)

The Use of Infrared Spectroscopy to Determine the Quality of Carbonate-Rich Diatomite Ores

Directory of Open Access Journals (Sweden)

Adriana Guatame-Garcia

2018-03-01

Full Text Available Diatomite, a rock formed by the accumulation of opaline diatom frustules, is a preferred raw material for the manufacturing of filters. Its uniqueness relies on the high porosity and inertness of the frustules. The presence of carbonates in some diatomite ores hinders these properties. The purpose of this study was to identify the type of carbonates and their association with the ore in a diatomite deposit, and to assess the suitability of determining the quality of the ore using techniques with potential for in-pit implementation. For this, run-of-mine samples were analysed using environmental scanning electron microscopy (ESEM and infrared spectroscopy. The ESEM images showed that carbonate is present as cement and laminae. The infrared data revealed that the carbonate minerals correspond to aragonite and calcite, and that their occurrence is linked to the total amount of carbonate in the sample. By using a portable spectral instrument that uses diffuse reflectance, it was possible to classify the spectra of the ore samples based on the carbonate content. These results indicate that infrared technology could be used on-site for determining the quality of the ore, thus providing relevant information to assist the optimisation of mining and beneficiation activities.

Effect of residual Al content on microstructure and mechanical properties of Grade B+Steel for castings for locomotives

Directory of Open Access Journals (Sweden)

Wang Kaifeng

2013-11-01

Full Text Available The bogie made of Grade B+ steel is one of the most important parts of heavy haul trains. Some accidents were found to be the result of fracture failure of the bogies. It is very important to find the reason why the fracture failure occurred. Because Al was added for the final deoxidation during the smelting process of the Grade B+Steel, residual Al existed to some extent in the castings. High residual Al content in the bogie casting was presumed to be the reason for the fracture. In this work, the influence of residual Al content in the range of 0.015wt.% to 0.3wt.% on the microstructure and mechanical properties of the Grade B+ Steel was studied. The experimental results showed that when the residual Al content is between 0.02wt.% and 0.20wt.%, the mechanical properties of the steel meet the requirements of technical specification for heavy haul train parts, and the fracture is typical plastic fractures. If the residual Al content is less than 0.02wt.%, the microstructures are coarse, and the mechanical properties can not meet the demand of bogie steel castings. When the residual Al content is more than 0.2wt.%, the elongation, reduction of area, and low-temperature impact energy markedly deteriorate. The fracture mode then changes from plastic fracture to cleavage brittle fracture. Therefore, the amount of Al addition for the final deoxidation during the smelting process must be strictly controlled. The optimum addition amount needs to be controlled within the range of 0.02wt.% to 0.20wt.% for the Grade B+Steel.

Trace-element and multi-isotope geochemistry of Late-Archean black shales in the Carajas iron-ore district, Brazil

DEFF Research Database (Denmark)

Cabral, A. R.; Creaser, R. A.; Naegler, T.

2013-01-01

The 250-300-m-thick Carajas Formation in the Carajas mineral province, northern Brazil, consists of banded iron formation (including giant high-grade iron-ore deposits) and minor black shale, overlying a thick pile (2-3 km) of about 2.75-Ga-old metabasalt. Carbonaceous shale with pyrite-and local...

Recovery of manganese from manganese oxide ores in the EDTA solution

Science.gov (United States)

Zhang, Chao; Wang, Shuai; Cao, Zhan-fang; Zhong, Hong

2018-04-01

A new process has been experimentally and theoretically established for the recovery of manganese from manganese oxide ores, mainly including the reductive leaching of manganese by ethylenediaminetetraacetic acid (EDTA), EDTA recovery, and manganese electrolysis. The experimental conditions for this process were investigated. Moderate leaching environment by EDTA with the pH in the range of 5-6 is of benefit to leach manganese from some manganese oxide ores with high-content impurities, such as iron and aluminum. Most of EDTA can be recovered by acidification. A small amount of the residual EDTA in the electrolyte can prevent the generation of anode mud. In addition, trimanganese tetroxide (Mn3O4) can be obtained by the roasting of the EDTA-Mn crystallized product.

Mineralogical-Geochemical Peculiarities of Ores in Pyritaceous Fields of Filizchai Type in the Greater Caucasus

Directory of Open Access Journals (Sweden)

NOVRUZ A. NOVRUZOV

2010-12-01

Full Text Available Pyritaceous fields of the south slope of the Greater Caucasus confined to the Lower-Middle Jurassic sandy clayey deposits are: polygenic polychrone formations which were formed by a complex of hydrothermal sedimentary, hydrothermal metasomatic and hydrothermal metamorphogenic processes of ore formation. Filizchai pyritaceous polymetallic field is the largest in the region and can be characterized by diversity of texture-mineralogical types of ores, rich mineral composition and with geochemical spectrum. Some of the admixture components (Cd, In, Tl, Ga, Ge, Se, Hg are only in isomorphic forms in ores, others (Te, Bi, Au, Ag, Co, Sn, As along with it characterize in their own minerals. The Co is mainly concentrated in pyrite, pyrrhotine; Ag, Bi and also Te – in galenite and chalcopyrite; Se – in pyrite, pyrrhotine and galenite; in sphalerite (mainly in marmatite and chalcopyrite; Cd, Ga, Ge – in sphalerite, mainly in cleiophane; Au – in pyrite and chalcopyrite; Tl – in galenite and colloform pyrite. In all sulphides selenium prevails over tellurium (excepting the late chalcopyrite and cobalt over nickel. Maximum amount of cobalt is confined to pyrite from pyritaceous polymetallic ores and late generation of pyrrhotine. The nature of the connection between chemical elements in ores coordinates with determined stages of minerals formation. The main productive stage of ore formation bringing the main mass of gold, silver, rare and other precious components of ores are sulphosalt polymetallic stage of sulphur ploymetallic stage. Comparative analysis of absolute content of gold, silver and values of gold-silver relation in pyrite fields ores of region with appropriate values in meteorite standard indirectly indicates the relationship between gold-silver mineralization and assimilation crust source.

Beneficiation studies of an uranium siliceous - phosphate ore

International Nuclear Information System (INIS)

Bruno, J.B.; Santos, A.T.; Santos Benedetto, J. dos

1980-01-01

The consolidation of the beneficiation studies of a low-grade uranium siliceous - phosphate ore (11% P 2 O 5 ) from Itataia region in the Northeast of Brazil, owned by Empresas Nucleares Brasileiras S.A. - NUCLEBRAS, are presented. Laboratory studies using froth flotation technique and applying statistical methods for data evaluation were made. Pilot plant tests in a 120 Kg/h scale were conducted as a consequence of the bench scale tests. The developed process using tall-oil as collector and starch as depressant gave a total yield of 80% for the P 2 O 5 and 71% the U 3 O 8 , for a 33% P 2 O 5 phosphate concentrate. (Author) [pt

Chemical analysis of copper and gold ores from Papua New Guinea (PNG) by means of X-ray fluorescence analysis

International Nuclear Information System (INIS)

Sugiyama, Kazumasa; Waseda, Yoshio; Pangum, L.S.; Witney, J.Y.

1995-01-01

X-ray fluorescence analysis (XRF) has been made for determining the contents of copper and gold in ores from PNG mines. An internal standard method of Cu Kα/Er Lβ 1 was used for the analysis of the common copper porphyry samples. The results clearly indicate that this technique is quite effective for analyzing any copper ores with complicated matrix elements. On the other hand, an addition method of the diluted Au solution was applied to gold ores. The results of the present XRF analysis were found to reasonably agree with those obtained by the inductively coupled plasma (ICP) technique. (author)

MR imaging of ore for heap bioleaching studies using pure phase encode acquisition methods

Science.gov (United States)

Fagan, Marijke A.; Sederman, Andrew J.; Johns, Michael L.

2012-03-01

Various MRI techniques were considered with respect to imaging of aqueous flow fields in low grade copper ore. Spin echo frequency encoded techniques were shown to produce unacceptable image distortions which led to pure phase encoded techniques being considered. Single point imaging multiple point acquisition (SPI-MPA) and spin echo single point imaging (SESPI) techniques were applied. By direct comparison with X-ray tomographic images, both techniques were found to be able to produce distortion-free images of the ore packings at 2 T. The signal to noise ratios (SNRs) of the SESPI images were found to be superior to SPI-MPA for equal total acquisition times; this was explained based on NMR relaxation measurements. SESPI was also found to produce suitable images for a range of particles sizes, whereas SPI-MPA SNR deteriorated markedly as particles size was reduced. Comparisons on a 4.7 T magnet showed significant signal loss from the SPI-MPA images, the effect of which was accentuated in the case of unsaturated flowing systems. Hence it was concluded that SESPI was the most robust imaging method for the study of copper ore heap leaching hydrology.

The distribution of naturally occurring radionuclides from ores processing to the environment - a case study of milling and treatment of ores for gold in Golden Star Resources of Bogoso Prestea Limited

International Nuclear Information System (INIS)

Gbadago, J.K.

2010-01-01

This research work was geared towards studying the distribution of naturally occurring radionuclides from the processing stages of oxide and sulphide ores for gold to the critical environment of the Golden Star Resources of Bogoso Prestea Limited in the Western region of Ghana. The study was carried out by measuring the natural radionuclide contents of raw feed ore and pulp samples from physical and chemical processing stages of oxide and sulphide ore treatment plants; tailings; de-silted sediments of a run-off from the tailings dam vicinity through a critical community and; soils and drinking water from the critical community. Also, as part of a comprehensive approach, the geochemical compositions were measured to determine any possible influence on the radionuclide distributions. Amongst the radionuclide decay chains, 238 U-series were the dominant throughout all the measurements. However, the concentrations are lower than the world permissible limits. The indicative doses associated with the activity concentration distributions in the processed feed ores at various processing stages ranged from 2 to 70 μSv/y in the oxide plant and from 2 to 108 μSv/y for the sulphide plant. If effective dose of ≤ 10 μSv/y recommended by IAEA for exemption from regulatory control is applied, the processing of ores in the plants must be regulated. However, the estimated annual effective dose received by the workers from any of these stages of operation did not exceed the range of 1-2 mSv recommended by the ICRP-75 (10 μSv/y ≤ Effective dose ≤ 1-2 mSv/y) for the exemption of a practice. This range is far lower than the annual occupational dose limit of 20 mSv/y recommended by IAEA for artificial radioactive sources. Imposing the IAEA recommendation of effective dose of ? 10 μSv/y for exemption from regulatory control of practices could result in many mining and other NORMs industries being regulated without any net benefit in terms of risk reduction. Conversely, Sn, As

Challenges with modifications of the McClean Lake mill to process midwest ore

International Nuclear Information System (INIS)

Nguyen, T.T.; Backham, L.

2010-01-01

Midwest is a unique uranium deposit with exceptionally high arsenic content. The ore body is located 17 km west of the McClean Lake operation. The McClean Lake mill will be modified to process Midwest ore and handle solid wastes from the Midwest water treatment plant. This paper describes the modifications required of the McClean Lake mill, process challenges associated with treatment of the arsenic, and the possibility of recovering nickel and cobalt as a by-product. It also reviews the complexity in the design of the Midwest water treatment facility which incorporates reverse osmosis technology with conventional physical-chemical water treatment. (author)

Bioleaching of Primary Nickel Ore Using Acidithiobacillus ferrooxidans LR Cells Immobilized in Glass Beads

Directory of Open Access Journals (Sweden)

Ellen Cristine Giese

2015-06-01

Full Text Available Sulphide minerals are one of the most important sources of value metals. For several years, a large number of hydrometallurgical and biotechnological processes have been developed to leach low-grade sulphide ores and the conditions are well established. However, the management of microorganisms in the bioleaching process is not easy to handle. In this paper, the use of immobilized cells of Acidithiobacillus ferrooxidans LR in glass beads in bioleaching of primary nickel ore was evaluated. The column experiments inoculated with immobilized cells of A. ferrooxidans LR showed the same efficiency than the conventional method using free cells and is promising for application on a larger scale as it ensuring integrity and activity of biomining microorganisms and reduce process costs. DOI: http://dx.doi.org/10.17807/orbital.v7i2.698 

The treatment of uranium ores

International Nuclear Information System (INIS)

Michel, P.

1979-01-01

After having described the main steps in the treatment of uranium ores, the author describes the treament activities for these ores, as they are organized in France and in the African countries having made cooperation agreements with France in this field [fr

Learning from Expository Texts: Classroom-Based Strategies for Promoting Comprehension and Content Knowledge in the Elementary Grades

Science.gov (United States)

Hall-Kenyon, Kendra M.; Black, Sharon

2010-01-01

One of the primary purposes of expository text in education is to teach new content. Because elementary grade children are accustomed to applying their literacy skills to reading and writing narratives, they must be taught new skills if they are to access expository content effectively. These skills and practices can be challenging because…

Ladinian skonca beds of the Idrija Ore Deposit (W Slovenia

Directory of Open Access Journals (Sweden)

Jože Čar

2013-12-01

part of sequence C has a carbonate structure (subsequence C1 and the top part has a siliceous structure (subsequence C2, the rocks cannot be distinguished from one another by their appearance. All are strongly bituminous and shaly. Sequence C is comprised of grey to black bituminous dolomite and quartz sandstone rich in pyrite and marcasite, dolomite or quartz siltstone, and shaly claystone with coal inclusions. The sequence of C rocks ends with clayey-lythic quartz sandstone containing remains of the brachiopod Discina. These are followed by various pyroclastic rocks of sequence D. The Skonca beds and the rich bedded cinnabar ores have various sedimentary structures which accurately define the events and environments of their origin. Except for the erosion channels, which are filled with dolomite gravel, there are no other presedimentary structures in the Skonca beds (subsequence C1. However, the beds are rich in synsedimentary physical forms, particularly various stratifications, laminations and various forms of graded bedding. Among the postsedimentary structures, mention should be made of the abundant sinking and slump structures. In some places, bioturbation and the replacement of organic particles with pyrite can be observed. The Skonca beds were deposited in a spatially complex, marsh-lacustrine-lagoonal environment. The rocks of sequence A and partly also of sequence B were formed in an alkaline, oxygen-rich environment, and the lithological units of subsequence C1 in a reductive environment. The rapid transitions among rocks indicate strictly limited and slow lateral inflows of fresh water into the marshy environment overgrown with low vegetation. The rocks in subsequence C2 prove that the freshwater marsh was flooded with sea water. Deposited in the shallow, closed lagoon overgrown with low vegetation were various bituminous shales, mudstones and sandstones filled with numerous radiolarians and needles of siliceous sponges and coal intercalations. The

The control of H2S in biogas using iron ores as in situ desulfurizers during anaerobic digestion process.

Science.gov (United States)

Zhou, Qiying; Jiang, Xia; Li, Xi; Jiang, Wenju

2016-09-01

In this study, five kinds of iron ores, limonite, hematite, manganese ore, magnetite and lava rock, were used as the in situ desulfurizers in the anaerobic digestion reactors to investigate their effects on controlling H2S in biogas. The results show that the addition of the five iron ores could significantly control the content of H2S in biogas, with the best performance for limonite. As limonite dosages increase (10-60 g/L), the contents of H2S in biogas were evidently decreased in the digesters with different initial sulfate concentrations (0-1000 mg/L). After the anaerobic digestion, the removed sulfur was mostly deposited on the surface of limonite. A possible mechanism of H2S control in biogas by limonite was proposed preliminarily, including adsorption, FeS precipitation, and Fe (III) oxidation. The results demonstrated that limonite was a promising in situ desulfurizer for controlling H2S in biogas with low cost and high efficiency.

Temporal Evolution of Volcanic and Plutonic Magmas Related to Porphyry Copper Ores Based on Zircon Geochemistry

Science.gov (United States)

Dilles, J. H.; Lee, R. G.; Wooden, J. L.; Koleszar, A. M.

2015-12-01

Porphyry Cu (Mo-Au) and epithermal Au-Ag ores are globally associated with shallow hydrous, strongly oxidized, and sulfur-rich arc intrusions. In many localities, long-lived magmatism includes evolution from early andesitic volcanic (v) and plutonic (p) rocks to later dacitic or rhyolitic compositions dominated by plutons. We compare zircon compositions from three igneous suites with different time spans: Yerington, USA (1 m.y., p>v), El Salvador, Chile (4 m.y., p>v), and Yanacocha, Peru (6 m.y., v>p). At Yerington granite dikes and ores formed in one event, at ES in 2 to 3 events spanning 3 m.y., and at Yanacocha in 6 events spanning 5 m.y. At both ES and Yanacocha, high-Al amphiboles likely crystallized at high temperature in the mid-crust and attest to deep magmas that periodically recharged the shallow chambers. At Yanacocha, these amphiboles contain anhydrite inclusions that require magmas were sulfur-rich and strongly oxidized (~NNO+2). The Ti-in-zircon geothermometer provides estimates of 920º to 620º C for zircon crystallization, and records both core to rim cooling and locally high temperature rim overgrowths. Ore-related silicic porphyries yield near-solidus crystallization temperatures of 750-650°C consistent with low zircon saturation temperatures. The latter zircons have large positive Ce/Ce* and small negative Eu/Eu*≥0.4 anomalies attesting to strongly oxidized conditions (Ballard et al., 2001), which we propose result from crystallization and SO2 loss to the magmatic-hydrothermal ore fluid (Dilles et al., 2015). The Hf, REE, Y, U, and Th contents of zircons are diverse in the magma suites, and Th/U vs Yb/Gd plots suggest a dominant role of crystal fractionation with lesser roles for both crustal contamination and mixing with high temperature deep-sourced mafic magma. Ce/Sm vs Yb/Gd plots suggest that magma REE contents at contamination are most evident in pre-ore magmas, whereas ore-forming intrusions at low temperatures are dominated by crystal

Mineral content in grains of seven food-grade sorghum hybrids grown in Mediterranean environment

Science.gov (United States)

Sorghum is a major crop used for food, feed and industrial purposes worldwide. The objective of this study was to determine the mineral content in grains of seven white food-grade sorghum hybrids bred and adapted for growth in the central USA and grown in a Mediterranean area of Southern Italy. The ...

Geological-economic analysis on the exploration of backup resources for depleted mines in Lujing uranium ore-field, central-southern China

International Nuclear Information System (INIS)

Li Deping; Wang Zhicheng; Fan Shaoyun

2006-01-01

With the geological-economic evaluation program for pithead heap-leaching mining uranium deposits developed by the authors and the data of column-leaching tests and the geological reserve, the geological-economic evaluation is made to the residual geological reserves of both Lujing and Huangfengling deposit, and the geological reserves of Yangjiaonao deposit of the depleted mines in Lujing uranium ore-field, central-southern China. The results of static analysis on these reserves show that the residual geological reserves of both Lujing and Huangfengling deposit belong to sub-profitable type, but the ones of Yangjiaonao deposit is profitable with 26.56% tax-before profit. 1 tU profitable type of ore from Yangjiaonao deposit can use 2.40-3.79 tU subprofitable type of ores from Lujing and Huangfengling deposit. In order to solving the problem on scarcity of backup resources of the depleted mines in Lujing uranium ore-field and using the existing sub-profitable type of geological reserves, it is suggested that the high grade of profitable type of deposits should be explored around the exhausting mines so that the production of the mines could be profitable by the pithead heap-leaching mining method with arrangement groups of both sub-profitable and profitable type of ores. (authors)

Tantalum and niobium carbides obtention by carbothermic reduction of columbotantalite ores

International Nuclear Information System (INIS)

Gordo, E.; Garcia-Carcedo, F.; Torralba, J.M.

1998-01-01

Tantalum and niobium carbides are characterized by its high hardness and chemical corrosion resistance. Both carbides, but mainly TaC, are used in hard metals (sintered carbides), together with their carbides, to manufacture cutting tools and dies in special machining applications involving mechanical shock at high temperature. Its use as reinforcement of wear resistant materials through powder metallurgy techniques are being investigated. However, the use of TaC is usually limited because of its high cost. Therefore tantalum carbide with niobium content, which is cheaper, is used. In this work the obtention of complex tantalum and niobium carbides from a Spanish columbotantalite ore is studied through relatively cheap and simple process as it is carbothermic reduction. Concentration of the ore, its reduction and the characterization of products are described. (Author) 11 refs

Content, format, gender and grade level differences in elementary students' ability to read science materials as measured by the cloze procedure

Science.gov (United States)

Williams, Richard L.; Yore, Larry D.

Present instructional trends in science indicate a need to reexamine a traditional concern in science education: the readability of science textbooks. An area of reading research not well documented is the effect of color, visuals, and page layout on readability of science materials. Using the cloze readability method, the present study explored the relationships between page format, grade level, sex, content, and elementary school students ability to read science material. Significant relationships were found between cloze scores and both grade level and content, and there was a significant interaction effect between grade and sex in favor of older males. No significant relationships could be attributed to page format and sex. In the area of science content, biological materials were most difficult in terms of readability followed by earth science and physical science. Grade level data indicated that grade five materials were more difficult for that level than either grade four or grade six materials were for students at each respective level. In eight of nine cases, the science text materials would be classified at or near the frustration level of readability. The implications for textbook writers and publishers are that science reading materials need to be produced with greater attention to readability and known design principles regarding visual supplements. The implication for teachers is that students need direct instruction in using visual materials to increase their learning from text material. Present visual materials appear to neither help nor hinder the student to gain information from text material.

Did the Kiruna iron ores form as a result of a metasomatic or igneous process? New U-Pb and Nd data for the iron oxide apatite ores and their host rocks in the Norrbotten region of northern Sweden

Science.gov (United States)

Westhues, A.; Hanchar, J. M.; Whitehouse, M. J.; Fisher, C. M.

2012-12-01

A number of iron deposits near Kiruna in the Norrbotten region of northern Sweden are of the iron oxide apatite (IOA) type of deposits; also referred to as Kiruna-type deposits. They are commonly considered a subgroup or end-member of iron oxide copper gold (IOCG) deposits, containing no economic grades of copper or gold. Both IOCG and IOA deposits are characterized by abundant low-Ti Fe oxides, an enrichment in REE, and intense sodium and potassium wall-rock alteration adjacent to the ores. Deposits of these types are of a great economic importance, not only for iron, but also for other elements such as rare earth elements (REE) or uranium. Kiruna, the type locality of the IOA type of mineral deposits, is the focus of this study. Despite a century-long mining history and 2500 Mt of iron ore produced in the region to date (with grades of 30 to 70 wt.% Fe), the genesis of these deposits is poorly understood: theories of a magmatic vs. a hydrothermal or metasomatic origin have been debated, and the timing of mineralization of the ores in the Norbotten region has never been directly dated. The results anticipated from this study will provide a better understanding of the nature of the IOA type of mineral deposits and their relation to IOCG deposits such as Olympic Dam in Australia. An array of geochemical methods is used in order to gain insights on the emplacement history of the host rocks, their subsequent alteration, and the ore genesis of these deposits. This includes in situ U/Pb geochronology of zircon, monazite, and titanite to constrain the timing between host rock emplacement, alteration and mineralization. Isotopic data from whole rocks and in situ at mineral scale will provide constraints on the involvement of hydrothermal fluids and their possible sources, as well as on the sources of Fe, U, and the REE. Newly obtained Sm-Nd isotopic data points to distinct source differences between host rocks, ore and alteration related samples. Preliminary in situ U

A procedure for acid leaching of ores of the sandstone type, particularly of uranium ores

International Nuclear Information System (INIS)

Fiala, P.; Baloun, S.; Hinterholzinger, O.

1990-01-01

Ore mixed with the enriched fraction of the leached ore is leached with sulfuric acid at 5 to 220 degC. Bulky particles are sorted out from the mixture and reduced in size, and particles with a higher proportion of the useful component are separated from them. The latter particles constitute the enriched fraction of the leached ore, which is partially or completely returned to the mixture with the entering ore. The sorting should preferably be performed in an aqueous system. The assets of this procedure include a better homogenization of the mixture with the acid, a better stability of the reaction mixture which brings about reduced adhesion and solidification, and the possibility of extending the reaction time and increasing the temperature. The reduction in size makes for a better access of the leaching agent to the useful minerals, and the returning of the leachate to the reaction system spares sulfuric acid. (M.D.)

Amenability of low-grade uranium towards column bioleaching by acidithiobacillus ferrooxidans

International Nuclear Information System (INIS)

Abhilash; Mehta, K.D.; Kumar, V.; Pandey, B.D.; Tamrakar, P.K.

2007-01-01

R and D studies were carried out at NML using Acidithiobacillus ferrooxidans (Ac.Tf) in column for the bio-recovery of uranium from the low-grade uranium ore containing 0.024% U 3 O 8 of Turamdih mines, Singhbhum. A recovery of 55.48% uranium was obtained in bio-leaching as against ∼ 44.9% in sterile control in 30 days at 1.7 pH in a column containing 2.5kg ore of particle size mainly in the range 5-1mm. In the large scale column, leaching with 80kg ore of particle size ∼ 0.5cm, uranium bio-recovery was found to be 69.8% in comparison to a recovery of 55% in control set at 1.7 pH in 50 days. The uranium recoveries followed indirect leaching mechanism. (author)

A multidimensional analysis and modelling of flotation process for selected Polish lithological copper ore types

Directory of Open Access Journals (Sweden)

Niedoba Tomasz

2017-01-01

Full Text Available The flotation of copper ore is a complex technological process that depends on many parameters. Therefore, it is necessary to take into account the complexity of this phenomenon by choosing a multidimensional data analysis. The paper presents the results of modelling and analysis of beneficiation process of sandstone copper ore. Considering the implementation of multidimensional statistical methods it was necessary to carry out a multi-level experiment, which included 4 parameters (size fraction, collector type and dosage, flotation time. The main aim of the paper was the preparation of flotation process models for the recovery and the content of the metal in products. A MANOVA was implemented to explore the relationship between dependent (β, ϑ, ε, η and independent (d, t, cd, ct variables. The design of models was based on linear and nonlinear regression. The results of the variation analysis indicated the high significance of all parameters for the process. The average degree of matching of linear models to experimental data was set at 49% and 33% for copper content in the concentrate and tailings and 47% for the recovery of copper minerals in the both. The results confirms the complexity and stochasticity of the Polish copper ore flotation.

Integrating the Theory of Sampling into Underground Mine Grade Control Strategies

Directory of Open Access Journals (Sweden)

Simon C. Dominy

2018-05-01

Full Text Available Grade control in underground mines aims to deliver quality tonnes to the process plant via the accurate definition of ore and waste. It comprises a decision-making process including data collection and interpretation; local estimation; development and mining supervision; ore and waste destination tracking; and stockpile management. The foundation of any grade control programme is that of high-quality samples collected in a geological context. The requirement for quality samples has long been recognised, where they should be representative and fit-for-purpose. Once a sampling error is introduced, it propagates through all subsequent processes contributing to data uncertainty, which leads to poor decisions and financial loss. Proper application of the Theory of Sampling reduces errors during sample collection, preparation, and assaying. To achieve quality, sampling techniques must minimise delimitation, extraction, and preparation errors. Underground sampling methods include linear (chip and channel, grab (broken rock, and drill-based samples. Grade control staff should be well-trained and motivated, and operating staff should understand the critical need for grade control. Sampling must always be undertaken with a strong focus on safety and alternatives sought if the risk to humans is high. A quality control/quality assurance programme must be implemented, particularly when samples contribute to a reserve estimate. This paper assesses grade control sampling with emphasis on underground gold operations and presents recommendations for optimal practice through the application of the Theory of Sampling.

Reducing the Entrainment of Gangue Fines in Low Grade Microcrystalline Graphite Ore Flotation Using Multi-Stage Grinding-Flotation Process

Directory of Open Access Journals (Sweden)

Xiaoqing Weng

2017-03-01

Full Text Available A suitable grinding fineness and flow-sheet could potentially reduce the mechanical entrainment of gangue minerals in the flotation process of microcrystalline graphite. In this study, the suitable grinding fineness of a commercial graphite ore was estimated by mineralogy analysis and laboratory grind-flotation tests. The target grind size of this ore should be 92% passing 74 μm based on the mineralogical evaluation and the flotation performance. A comparison of a single-stage and a three-stage grinding circuit was conducted. Experimental results demonstrated that the three-stage grinding circuit could effectively improve the separation effect, which was attributed to the reduction of slimes. In the end, a more desirable beneficiation result was obtained with the application of three-stage grinding-flotation process by minimizing gangue entrainment.

Preconcentration of low grade uranium ores by gravity and magnetic methods: a case study with copper tailings from Singhbhum, Bihar, India

International Nuclear Information System (INIS)

Natarajan, R.; Sreenivas, T.; Krishna Rao, N.

1992-01-01

The physical beneficiation methods applied to uranium ores are gravity and magnetic techniques. Feasibility of application of these two techniques has been industrially demonstrated in the case of Palabora copper-uranium ores and Witwatersrand gold-uranium ores respectively. In India exhaustive studies have been carried out on the application of gravity and magnetic methods for preconcentration of uranium values from tailings of copper plants at Surda, Rakha and Mosabani in Singhbhum. While recovery by shaking tables is poor owing to non-liberation and inefficient recovery in finer particle sizes (-37μm), gravity machines like Bartles Mozely Separator and Bartles Cross Belt Concentrator are able to give improved recovery in sizes down to about 15μm. Application of Wet High Intensity Magnetic Separator (WHIMS) is able to improve the recovery to about 75 to 85% from the three tailings, and the improvement is due to the ability of WHIMS collect the micaceous mineral particles containing composite uranium values, as well as uraninite particles down to about 10μm in size. WHIMS is inefficient in recovering uraninite particles below 5μm. High Gradient Magnetic Separator and Super Conducting High Gradient Magnetic Separator, on the other hand, are able to give enhanced recovery of even < 5μm uraninite particles. With the improved technology of gravity and magnetic methods now available, it should now be techno-economically feasible to employ preconcentration of low tenor uranium ores by physical beneficiation, prior to chemical processing. (author). 25 refs. 8 figs, 5 tabs

Clean recycle and utilization of hazardous iron-bearing waste in iron ore sintering process.

Science.gov (United States)

Gan, Min; Ji, Zhiyun; Fan, Xiaohui; Chen, Xuling; Zhou, Yang; Wang, Guojing; Tian, Ye; Jiang, Tao

2018-04-18

Applying recycled iron-bearing waste materials (RIM) into iron ore sintering process is the general disposal approach worldwide, while its use is still a thorny problem. Results showed that adding RIM increased contents of hazardous elements (K, Na, Pb, Zn, and Cl) in sinter product, and also enhanced emission concentration of PM 2.5 in flue gas; increasing reaction temperature, and contents of CaO & coke breeze in raw mixtures improved hazardous elements removal. Based on these features, a novel method through granulating natural iron ores and RIM separately and distributing granulated RIM in bottom sintering layers was proposed for clean RIM cycle. When recycling 5% RIM, granulating RIM separately with higher contents of CaO and coke breeze removed hazardous elements effectively, the contents of which in sinter were reduced to comparable level of the case without RIM. Moreover, distributing RIM in bottom sintering layer reached intensive release of hazardous elements and PM 2.5 during sintering, which reduced the flue gas volume needing purification by about 2/3. Through activated carbon purification, about 60% of PM 2.5 comprised high contents of hazardous elements was removed. Novel technique eliminated the negative impact of RIM and has the prospect to reach clean recycle in sinter-making plants. Copyright © 2018. Published by Elsevier B.V.

The Crouzille (Haute-Vienne, France) uranium ores. Half a century of human and industrial adventure in Limousin

International Nuclear Information System (INIS)

Bavoux, B.; Guiollard, P.C.

1998-01-01

The 16 uranium deposits of the Crouzille (Haute-Vienne, France) have produced 25000 tons of uranium between 1950 and 1995. The uranium content of the ores ranges from 1 to 10/1000. The main production came from the underground exploitation up to 300 m of depth. This book presents the historical aspects of this industrial and human epopee and describes with details the underground exploitation of the ore, its processing and the rehabilitation of the site after the mines have closed down. (J.S.)

Quantitative Investigation of Roasting-magnetic Separation for Hematite Oolitic-ores: Mechanisms and Industrial Application

Directory of Open Access Journals (Sweden)

Peng Tiefeng

2017-12-01

Full Text Available Natural high-quality iron can be directly applied to pyro-metallurgy process, however, the availability of these ores has become less and less due to exploitation. This research reports a systematic approach using reduction roasting and magnetic separation for oolitic iron ores from west Hubei Province. Firstly, a mineralogical study was performed and it was shown that the oolitic particles were mainly composed of hematite, with some silicon-quartz inside the oolitic particle. Then, the roasting temperature was examined and shown to have significant influence on both Fe recovery and the Fe content of the concentrate. Also the Fe content gradually increased as the temperature increased from 700 to 850 °C. The most important aspects are the quantitative investigation of change of mineral phases, and reduction area (with ratio during the reduction roasting process. The results showed that Fe2O3 decreased with temperature, and Fe3O4 (magnetite increased considerably from 600 to 800 °C. The reductive reaction was found to occur from the outside in, the original oolitic structure and embedding relationship among the minerals did not change after roasting. Finally, 5% surrounding rock was added to mimic real industrial iron beneficiation. This study could provides useful insight and practical support for the utilization of such iron ores.

EXPLANATORY MODEL OF SPOT PRICE OF IRON ORE

Directory of Open Access Journals (Sweden)

Juan Enrique Villalva A.

2015-11-01

Full Text Available The objective of this study was to construct an explanatory model of the spot price of iron ore in the international market. For this, the method of multiple linear regressions was used. As a dependent variable, the spot price of iron ore (62% Fe China Tianjin port was taken, between 2010 and 2013. As independents variables were taken seven variables of international iron ore market. The resulting model includes variables: Iron ore inventory in Chinese ports, Baltic Dry Index (BDI, Iron ore exports from Brazil & Australia and Chinese Rebar Steel Price, as explanatory variables of the behavior of the spot price of iron ore in the international market. The model has an adjusted coefficient of determination R2 of 0.90, and was validated by comparing its predictions vs. known values of 2014.

A study of VMS ore deposits by the proton microprobe

International Nuclear Information System (INIS)

Huston, D.L.; Large, R.R.; Bottril, R.S.; Sie, S.H.; Ryan, C.G.

1991-01-01

As part of studies into the mineralogical distribution of gold in volcanogenic massive sulfide (VMS) ore deposits PIXE analysis by the proton microprobe has been used to determine the gold content of pyrite and arsenopyrite from the Rosebery, Mt. Chalmers and Mt. Lyell deposits. In addition, the concentrations of Co, Ni, Cu, Zn, As, Sr, Y, Zr, Mo, Ag, Sb, Te, Au, Tl, Pb and Bi were also determined. 4 refs., 1 tab

Introduction to ore geology

International Nuclear Information System (INIS)

Evans, A.M.

1987-01-01

This textbook on ore geology is for second and third year undergraduates and closely parallels the undergraduate course given in this subject at England's University of Leicester. The volume covers three major areas: (1) principles of ore geology, (2) examples of the most important types of ore deposits, and (3) mineralization in space and time. Many chapters have been thoroughly revised for this edition and a chapter on diamonds has been added. Chapters on greisen and pegmatite have also been added, the former in response to the changing situation in tin mining following the recent tin crisis, and the latter in response to suggestions from geologists in a number of overseas countries. Some chapters have been considerably expanded and new sections added, including disseminated gold deposits and unconformity-associated uranium deposits. The author also expands on the importance of viewing mineral deposits from an economic standpoint

Decomposition of aluminosilicate ores of Afghanistan by hydrochloric acid

International Nuclear Information System (INIS)

Mamatov, E.D.; Khomidi, A.K.

2015-01-01

Present article is devoted to decomposition of aluminosilicate ores of Afghanistan by hydrochloric acid. The physicochemical properties of initial aluminosilicate ores were studied by means of X-ray phase, differential-thermal analysis methods. The chemical and mineral composition of aluminosilicate ores was considered. The kinetics of acid decomposition of aluminosilicate ores composed of two stages was studied as well. The flowsheets of complex processing of aluminium comprising ores by means of chloric and acid methods were proposed.

The production and use of citric acid for the removal of potassium from the iron ore concentrate of the Sishen Iron Ore Mine, South Africa

Directory of Open Access Journals (Sweden)

Peter J. Williams

2010-04-01

Full Text Available The depletion of the richer iron ore worldwide has made it necessary to process lower quality iron ore. Certain substances, such as potassium, contained within the lower quality iron ore, have a detrimental effect on the smelting process during steel manufacturing. Therefore, international steel-making companies charge penalties when purchasing iron ore concentrates containing high concentrations of potassium. To date, lower quality iron ore has been blended with high quality iron ore in an attempt to alleviate the potassium concentrations in the export iron ore; however, the ratio of low quality iron ore to high quality iron ore is increasing, thereby becoming an escalating problem within the economic functioning of the Sishen Iron Ore Mine. It has, therefore, become necessary to develop an economically viable and environmentally friendly process to reduce the high potassium concentrations contained in the iron ore concentrate of the Sishen Iron Ore Mine. In this study, we compared solid substrate and submerged fermentation using Aspergillus niger for the production of citric acid, which is used for the chemical leaching of potassium from the iron ore concentrate. It was found that submerged fermentation proved to be more economical and efficient, producing a maximum citric acid concentration of 102.3 g/L in 96 h of fermentation. ‘Heap leaching’ simulation experiments were found to be uneconomical, due to the required addition of fungal growth medium every 5 days as a result of growth factor depletion within this time; however, this process removed 17.65% of the potassium from the iron ore concentrate. By contrast, chemical leaching of potassium from the iron ore concentrate proved to be most efficient when using a 1 mol citric acid leaching solution at 60 ºC, removing 23.53% of the potassium contained within the iron ore concentrate. Therefore, the most economical and efficient process for the removal of potassium from the iron

Effect of desliming on the flotation of a complax copper ore from China

OpenAIRE

Chen Yong; Song Yong Sheng; Li Wen Juan; Zhou Gui Ying

2016-01-01

The complex copper oxide ore sample was taken from Deerni copper deposit, Qinghai Province of China. Batch flotation tests had been conducted to upgrade the copper concentrate by conventional amyl xanthate reagents under 73% -74 μm of the particle size; however, the unsatisfied results (Cu grade of 18.21% and recovery of 59.25%) were obtained. Also there are a large amount of slimes trapped in the concentrate and high-dosages consumption of reagents, for example, more than 2.5 kg/t sodium sul...

Metal recovery from high-grade WEEE

DEFF Research Database (Denmark)

Bigum, Marianne; Brogaard, Line Kai-Sørensen; Christensen, Thomas Højlund

2012-01-01

. The modeled metallurgical treatment facility included a Kaldo plant, a converter aisle, an anode refinery and a precious metal refinery. The metallurgic treatment showed significant environmental savings when credited the environmental load from avoided production of the same amount of metals by mining...... and refining of ore. The resource recovery per tonne of high-grade WEEE ranged from 2 g of palladium to 386 kg of iron. Quantified in terms of person-equivalents the recovery of palladium, gold, silver, nickel and copper constituted the major environmental benefit of the recovery of metals from WEEE....... These benefits are most likely underestimated in the model, since we did not find adequate data to include all the burdens from mining and refining of ore; burdens that are avoided when metals are recovered from WEEE. The processes connected to the pre-treatment of WEEE were found to have little environmental...

Improved leaching process for metal ores

International Nuclear Information System (INIS)

Kar-Kwan Yung, K.; Barlow, C.B.; Glass, J.R.

1980-01-01

The general overall sequence of process steps in the technique of the invention in set forth. In sequence, the ore is crushed, and solubilizing reagents and moisture are added to the crushed ore in preselected controlled portions. The mixture of ore, reagent, and moisture is then cured followed in the preferred process by conditioning for filtration. The slurry that is produced from conditioning is then subjected to multiple stage washing on a belt filter. The filtrate is further processed for metal value recovery and the solids are transported to tailings disposal

Mineralogical and paragenetical problems of the Mecsek uranium ore

International Nuclear Information System (INIS)

Vincze, J.; Fazekas, V.

1979-01-01

The latest results of the ore-mineralogical examination of the uranium ore of a deposit included in Permian sandstones in the Mecsek Mountains, southern Hungary, are presented. The phases of the minerals belonging to the uranium oxide series and their types of development, the post-coffinite nasturan pseudomorphs and the relationship between nasturan and coffinite are dealt with. Of the sulphide ore minerals associated with uranium ore mineralization the type determinant mineral is pyrite, i.e. the mineral forming their bulk and partly represented by characteristically finely aggregated ''bacteriopyrite'' and/or spherical pyrite and ''framboidal pyrite. The textural pattern of the ore mineralization is of typically matrix type. The matrix of sandstone is constituted by carbonate minerals, ''hydromicas'' and ore minerals. The matrix and, consequently, the ore minerals will corrode and consume the allothigenic detrital rockforming minerals, the feldspar, quartz-porphyry and quartz. (A.L.)

XPS and FTIR spectroscopic study on microwave treated high phosphorus iron ore

International Nuclear Information System (INIS)

Omran, Mamdouh; Fabritius, Timo; Elmahdy, Ahmed M.; Abdel-Khalek, Nagui A.; El-Aref, Mortada; Elmanawi, Abd El-Hamid

2015-01-01

Highlights: • The effect of microwave radiation on structure and chemical state of high phosphorus iron ore was studied. • FTIR analyses showed that after microwave radiation the functional chemical groups of phosphorus bearing minerals (fluorapatite) dissociated. • High resolution XPS analyses of Fe 2p peaks showed that after microwave radiation a portion of Fe(+III) was reduced to Fe(+II). • Microwave radiation had a positive effect on the magnetic properties of iron oxide, through formation of ferromagnetic phases. - Abstract: A growing interest in microwave heating has emerged recently. Several potential microwave applications regarding minerals’ processing have been investigated. This paper investigates the effect of microwave radiation on Egyptian high phosphorus iron ore. Three different iron ore samples have varying Fe 2 O 3 and P 2 O 5 contents and mineralogical textures were studied. A comparative study has been carried out between untreated and microwave treated iron ore. XRD and FTIR analyses showed that after microwave radiation the crystallinity of iron bearing minerals (hematite) increased, while the functional chemical groups of phosphorus bearing minerals (fluorapatite) and other gangues dissociated. High resolution XPS analyses of Fe 2p peaks showed that after microwave radiation a portion of Fe(+III) was reduced to Fe(+II). This means that after microwave radiation iron oxide (hematite, Fe 3+ ) transformed into more magnetic phase. The results indicated that microwave radiation had a positive effect on the magnetic properties of iron oxide, through formation of ferromagnetic phases

Nanoscale Study of Clausthalite-Bearing Symplectites in Cu-Au-(U Ores: Implications for Ore Genesis

Directory of Open Access Journals (Sweden)

Nicholas D. Owen

2018-02-01

Full Text Available Symplectites comprising clausthalite (PbSe and host Cu-(Fe-sulphides (chalcocite, bornite, and chalcopyrite are instructive for constraining the genesis of Cu-Au-(U ores if adequately addressed at the nanoscale. The present study is carried out on samples representative of all three Cu-(Fe-sulphides displaying clausthalite inclusions that vary in size, from a few µm down to the nm-scale (<5 nm, as well as in morphology and inclusion density. A Transmission Electron Microscopy (TEM study was undertaken on foils prepared by Focussed Ion Beam and included atom-scale High-Angle Annular Dark-Field Scanning TEM (HAADF-STEM imaging. Emphasis is placed on phase relationships and their changes in speciation during cooling, as well as on boundaries between inclusions and host sulphide. Three species from the chalcocite group (Cu2–xS are identified as 6a digenite superstructure, monoclinic chalcocite, and djurleite. Bornite is represented by superstructures, of which 2a and 4a are discussed here, placing constraints for ore formation at T > 265 °C. A minimum temperature of 165 °C is considered for clausthalite-bearing symplectites from the relationships with antiphase boundaries in 6a digenite. The results show that alongside rods, blebs, and needle-like grains of clausthalite within the chalcocite that likely formed via exsolution, a second, overprinting set of replacement textures, extending down to the nanoscale, occurs and affects the primary symplectites. In addition, other reactions between pre-existing Se, present in solid solution within the Cu-(Fe-sulphides, and Pb, transported within a fluid phase, account for the formation of composite, commonly pore-attached PbSe and Bi-bearing nanoparticles within the chalcopyrite. The inferred reorganisation of PbSe nanoparticles into larger tetragonal superlattices represents a link between the solid solution and the symplectite formation and represents the first such example in natural materials

Enumeration and characterization of microorganisms associated with the uranium ore deposit at Cigar Lake, Canada. Informal report

International Nuclear Information System (INIS)

Francis, A.J.; Joshi-Tope, G.; Gillow, J.B.; Dodge, C.J.

1994-03-01

The high-grade uranium deposit at Cigar Lake, Canada, is being investigated as a natural analog for the disposal of nuclear fuel waste. Geochemical aspects of the site have been studied in detail, but the microbial ecology has not been fully investigated. Microbial populations in an ore sample and in groundwater samples from the vicinity of the ore zone were examined to determine their effect on uranium mobility. Counts of the total number of bacteria and of respiring bacteria were obtained by direct microscopy, and the viable aerobic and anaerobic bacteria were assessed as colony forming units (CFUs) by the dilution plating technique. In addition, the population distribution of denitrifiers, fermenters, iron- and sulfur-oxidizers, iron- and sulfate-reducers, and methanogens was determined by the most probable number (MPN) technique

Radiometric enrichment of nonradioactive ores

International Nuclear Information System (INIS)

Mokrousov, V.A.; Lileev, V.A.

1979-01-01

Considered are the methods of mineral enrichment based on the use of the radioation of various types. The physical essence of enrichment processes is presented, their classification is given. Described are the ore properties influencing the efficiency of radiometric enrichment, methods of the properties study and estimation of ore enrichment. New possibilities opened by radiometric enrichment in the technology of primary processing of mineral raw materials are elucidated. A considerable attention is paid to the main and auxiliary equipment for radiometric enrichment. The foundations of the safety engineering are presented in a brief form. Presented are also results of investigations and practical works in the field of enrichment of ores of non-ferrous, ferrous and non-metallic minerals with the help of radiometric methods

Effect of desliming on the flotation of a complax copper ore from China

Directory of Open Access Journals (Sweden)

Chen Yong

2016-01-01

Full Text Available The complex copper oxide ore sample was taken from Deerni copper deposit, Qinghai Province of China. Batch flotation tests had been conducted to upgrade the copper concentrate by conventional amyl xanthate reagents under 73% -74 μm of the particle size; however, the unsatisfied results (Cu grade of 18.21% and recovery of 59.25% were obtained. Also there are a large amount of slimes trapped in the concentrate and high-dosages consumption of reagents, for example, more than 2.5 kg/t sodium sulfide and 1.5 kg/t sodium silicate at only one-staged roughing. Based on the analysis of the sample, most of gangues are clay, feldspar and mica, which may easy to over-grind and deteriorate the flotation process either on reagents consumption or slurry fluidity or viscosity. A hydro-cyclone had been introduced to pre-concentrate the oxide ore by scrubbing the slime before flotation, which can result obviously in reducing the dosages of sodium sulfide from 2.5 Kg/t to 1 Kg/t, and raising the grade of Cu in the concentrate from 18.21% to 26.65% at the expense of about 1% recovery of Cu. In this paper, the effects on the recovery of Cu by the different dosages of flotation reagents with or without de-sliming were studied, with the objective of determining the different effects on the functions of flotation reagents by slime during flotation.

Radiation protection of workers in mining and processing of uranium ore

International Nuclear Information System (INIS)

Khan, A.H.; Sahoo, S.K; Puranik, V.D.

2003-01-01

Low grade of uranium ore mined from three underground mines is processed in a mill at Jaduguda in eastern India to recover uranium concentrate in the form of yellow cake. Radiation protection of workers is given due importance at all stages of these operations. Dedicated Health Physics Units and Environmental Survey Laboratories established at the site regularly carry out in-plant and environmental surveillance to keep radiation exposure of workers and the members of public within the limits prescribed by the regulatory body. The limits set by the national regulatory body based on the international standards recommended by the ICRP and the IAEA are followed. In the uranium mines, external gamma radiation, radon and airborne activity due to radioactive dust are monitored. Similarly, in the uranium ore processing mill, gamma radiation and airborne radioactivity due to long-lived α-emitters are monitored. Personal dosimeters are also issued to workers. The total radiation exposure of workers from external and internal sources is evaluated from the area and personal monitoring data. It has been observed that the average radiation dose to workers has been below 10 mSvy -1 and all exposures are well below 20 mSvy -1 at all stages of operations. Adequate ventilation is provided during mining and ore processing operations to keep the concentrations of airborne radioactivity well below the derived limits. Workers use personal protective appliances, where necessary, as a supplementary means of control. The monitoring methodologies, results and control measures are presented in the paper. (author)

Geological structure and prospects of noble metal ore mineralization of the Khayrkhan gabbroid massif (Western Mongolia)

Science.gov (United States)

Kurumshieva, K. R.; Gertner, I. F.; Tishin, P. A.

2017-12-01

An analysis of the distribution of noble metals in zones of sulfide mineralization makes it possible to justify the isolation of four ore-bearing horizons with a specific geochemical zonation. A rise in the gold content relative to palladium and platinum is observed from the bottom upwards along the section of the stratified series of gabbroids. The study of the mineral phases of sulphides and the noble minerals itself indicates the evolution of hydrothermal solutions, which determines the different activity and mobility of the fluid (mercury, tellurium, sulfur) and ore (copper, nickel, iron, platinum, gold and silver) components.

The use of radiometric-logging techniques to determine uranium grade in certain mineralised Karoo boreholes

International Nuclear Information System (INIS)

Corner, B.; De Beer, G.P.

1976-05-01

During the period September-October 1975, 22 mineralised boreholes in nine different Karoo uranium occurrences were logged radiometrically with the aim of determining to what accuracy the actual uranium grade could be predicted from the gamma logs. The true uranium grades of the mineralised zones logged were known from existing chemical analyses. The results showed that the uranium grades could be predicted to an accuracy of better than 10% through the use of gamma-logging equipment calibrated at Pelindaba, provided that the ore was in equilibrium and that little or no thorium was present. Disequilibrium is, however, prevalent in the Karoo, and in the holes logged it occurred by depletion of uranium relative to its gamma-emitting daughter products. Such effects were mostly confined to the zone above the water table, and it is concluded that for Karoo-type occurrences, the high radiometric background levels observed over extended distances in some boreholes were indicative of radon-gas buildup, and hence of disequilibrium. It is further concluded that radiometric borehole logging can largely replace chemical analyses in the determination of uranium grade for ore-reserve calculations, although chemical checks for disequilibrium would always be necessary [af

Effect of particle size on the froth floatation of Sokoto phosphate ore

Directory of Open Access Journals (Sweden)

U.A. Hassan

2016-06-01

Full Text Available Effect of particle size on the froth floatation of Sokoto phosphate ore for its beneficiation has been investigated and established. The research has been conducted using various reagents, pH(s at different sieve size fractions. Bench scale flotation tests were carried out on -250+180μm, -180+106μm, -106+75μm, -75+45μm and -45+38μm particle size fractions after screening in order to determine the optimum flotation feed size distribution using 1 liter Denver flotation cell. The results of the scoping flotation studies using a conditioning Pulp Density of 60%Solids, pH9, 800g/t reagent dosage for AERO704 Promoter (Fatty Acid and flotation pulp density of 28.5% Solids show that +106μm particle size gave the highest assay content of 20.4% P2O5 with a recovery of 76.2% compared to +38μm (19.9%P2O5 and recovery of 43.2% and +180μm (19.4%P2O5 and 24.1% recovery in their floats (concentrates but with no perfect separation as the tailings fraction also contained similar grades with slight differences.

Ore reserve estimation of uranium deposit Zirovski vrh

International Nuclear Information System (INIS)

Lukacs, E.

1979-01-01

The uranium ore deposit Zirovski vrh is in the Permian sediments of Northwest Yugoslavia. Lenticular bodies occur at several stratiform levels in grey, medium-grained sandstone. The ore deposit will be mined entirely by underground methods. It is possible to define three stages of deposit evaluation requiring different densities of exploration effort: preliminary evaluation of in situ ore reserves; evaluation of mineable ore reserves; evaluation of production capability and mine planning. The drilling density increases markedly with each succeeding stage. The optimal drilling density for all three stages of evaluation should be determined, but there is some concern that too close spaced drilling would considerably increase the exploration costs without a corresponding increase in effectiveness. On the other hand, too sparsely spaced drilling may result in some difficulties in following the ore in mining. The paper treats the problem of the density of drilling for evaluation of mineable ore reserves compared to that required for mine planning and mine production capability. The purpose of investigation of mineral raw materials is to define economic deposits (ore bodies). To evaluate the deposit economically an accurate reserve estimate is required. If it is accordingly established that such an estimate is within the degree of admissible error, the purpose of the exploration is satisfied. However, the problem as to whether the drilling grid is sufficiently dense remains, because the majority of estimates of ore reserves do not provide a measure of the reliability of the estimate. (author)

A statistical approach to the experimental design of the sulfuric acid leaching of gold-copper ore

Directory of Open Access Journals (Sweden)

Mendes F.D.

2003-01-01

Full Text Available The high grade of copper in the Igarapé Bahia (Brazil gold-copper ore prevents the direct application of the classic cyanidation process. Copper oxides and sulfides react with cyanides in solution, causing a high consumption of leach reagent and thereby raising processing costs and decreasing recovery of gold. Studies have showm that a feasible route for this ore would be a pretreatment for copper minerals removal prior to the cyanidation stage. The goal of this experimental work was to study the experimental conditions required for copper removal from Igarapé Bahia gold-copper ore by sulfuric acid leaching by applying a statistical approach to the experimental design. By using the Plackett Burman method, it was possible to select the variables that had the largest influence on the percentage of copper extracted at the sulfuric acid leaching stage. These were temperature of leach solution, stirring speed, concentration of sulfuric acid in the leach solution and particle size of the ore. The influence of the individual effects of these variables and their interactions on the experimental response were analyzed by applying the replicated full factorial design method. Finally, the selected variables were optimized by the ascending path statistical method, which determined the best experimental conditions for leaching to achieve the highest percentage of copper extracted. Using the optimized conditions, the best leaching results showed a copper extraction of 75.5%.

Geology of eastern Smith Lake ore trend, Grants mineral belt

International Nuclear Information System (INIS)

Ristorcelli, S.J.

1980-01-01

The sandstones in the Brushy Basin Member of the Morrison Formation (Jurassic) are the ore-bearing horizons of the eastern Smith Lake area. The Brushy Basin Member in this district consists of three sandstones with interbedded mudstones. Only the lower two sandstones contain ore. The sandstones are fine to coarse grained, well rounded, and arkosic, representing continental stream sediments. The lower sandstone contains rollfront ore. The redox interface is laterally extensive and well defined, extending at least 7 mi (11 km) west of the Bluewater fault zone. The ore generally occurs at the redox boundary but occasionally will be up to 1500 ft (450 m) updip. Limonitic alteration, where present, is downdip from the hematitic zone and is 100-1,500 ft (30 to 450 m) wide. The middle sandstone contains both trend ore and roll-front ore. The trend ore occurs downdip from the redox front in unoxidized ground. The redox front in the middle sand is also laterally extensive but displays a wedge shape, rather than a C shape. The clay assemblages of the two types of ore are different: the trend ore occurs in sands with the pore spaces filled with kaolinite; the roll-front ore is associated with altered illite-montmorillonite as grain coatings. Hematitic alteration is asociated with the latter. A second stage of kaolinite coats the illite-montmorillonite. Two periods of mineralization are suggested, but no absolute dates are known. The trend ore is the oldest (Jurassic) and is similar to the ore found in unoxidized ground elsewhere in the Grants region. The rollfront ore could be Laramide or post-Laramide because of its association with local Laramide structures

The actual status of uranium ore resources at Eko Remaja Sector: the need of verification of resources computation and geometrical form of mineralization zone by mining test

International Nuclear Information System (INIS)

Johan Baratha; Muljono, D.S.; Agus Sumaryanto; Handoko Supalal

1996-01-01

Uranium ore resources calculation was done after ending all of geological work step. Estimation process of ore resources was started from evaluation drilling, continued with borehole logging. From logging, the result has presented in anomaly graphs, then was processed to determine thickness and grade value of ore. Those mineralization points were correlated one another to form mineralization zones which have direction of N 270 degree to N 285 degree with 70 degree dip to North. From Grouping the mineralization distribution, 19 mineralization planes was constructed which contain 553 ton of U 3 O 8 measured. It is suggested that before expanding measured ore deposit area, mining test should be done first at certain mineralization planes to prove the method applied to calculate the reserve. Results form mining test could be very useful to reevaluate all the work-step done. (author); 4 refs; 2 tabs; 8 figs

Iron Ore Industry Emissions as a Potential Ecological Risk Factor for Tropical Coastal Vegetation

Science.gov (United States)

Kuki, Kacilda N.; Oliva, Marco A.; Pereira, Eduardo G.

2008-07-01

In the coastal zone of the Espírito Santo state, Brazil, fragments of restinga, which form a natural ecosystem, share their space with an increasing number of iron ore industries. The iron ore dust and SO2 originating from the industry processing activities can interfere with the vegetation of the adjacent ecosystems at various levels. This study was undertaken in order to evaluate the effects of industry emissions on representative members of the restinga flora, by measuring physiological and phenological parameters. Foliar samples of Ipomoea pes caprae, Canavalia rosea, Sophora tomentosa, and Schinus terebinthifolius were collected at three increasing distances from an ore industry (1.0, 5.0, and 15.0 km), and were assessed for their dust deposition, chlorophyll, and Fe content. Phenological monitoring was focused on the formation of shoots, flowers, and fruits and was also performed throughout the course of a year. The results showed that the edaphic characteristics and the mineral constitutions of the plants were affected by industry emissions. In addition, the chlorophyll content of the four species increased with proximity to the industry. Phenological data revealed that the reproductive effort, as measured by fruit production, was affected by emissions and S. tomentosa was the most affected species. The use of an integrative approach that combines biochemical and ecological data indicates that the restinga flora is under stress due to industry emissions, which on a long-term basis may put the ecosystem at risk.

Micro-mechanical investigation of the effect of fine content on mechanical behavior of gap graded granular materials using DEM

Directory of Open Access Journals (Sweden)

Taha Habib

2017-01-01

Full Text Available In this paper, we present a micro-mechanical study of the effect of fine content on the behavior of gap graded granular samples by using numerical simulations performed with the Discrete Element Method. Different samples with fine content varied from 0% to 30% are simulated. The role of fine content in reinforcing the granular skeleton and in supporting the external deviatoric stress is then brought into the light.

Ore grade manganese nodules from the central Indian basin: an evaluation

Digital Repository Service at National Institute of Oceanography (India)

Sudhakar, M.

Comparative studies on manganese nodules from two different areas (S and R) in the Central Indian Basin show distinct variations in their composition, grade (percent Ni + Cu), and abundance (kg/m2), which are explained in terms of various genetic...

Trace and rare earth elements fractionation in volcanic- and sediment-hosted Mn ores: a study case of Sardinia (western Italy).

Science.gov (United States)

Sinisi, Rosa

2015-04-01

It is widely accepted that, regardless of the geological environment (continental, marine or hydrothermal), the occurrences of clay minerals and/or mineral phases with clay-type crystal structure (as zeolites and Mn-oxides), play a key role in the trace elements and REEs uptake processes. The REE resources are produced mostly from ion-adsorption type REE deposits of southern China that are formed by weathering of granitic rocks and subsequent chemical adsorption of REE on clay minerals. A significant group of minerals with a high metal uptake capacity is represented by Mn oxides. Their "tunnel" structure, in fact, allows both the absorption (inside the minerals) and adsorption (outside the minerals) of cations and anions producing metal accumulations with economic and environmental significance. However, the ores, mainly that forming within sedimentary environment, often have impurities due to presence of minerals unrelated to mineralization. These minerals can significantly alter the compositional features of the ores and suggest misleading conclusions. In Sardinia (Italy, western Mediterranean), Mn-oxide mineralizations occur and recently their origin has been discussed and identified (Sinisi et al. 2012). In this study the mineralogical and chemical compositions of the Sardinian sediment-hosted and volcanic-hosted Mn-ore are exhibit exploring the possibility that they can represent exploitable trace and REE mineralizations. High contents of metals characterize these Mn deposits. Besides some trace elements (Ni, Cr, Zn, Cu, As, Pb, and U) that commonly typify the Mn oxi-hydroxide ores, all rare earth elements showed high concentrations in the Sardinian deposits, comparable to those of the main actually exploited REE sinks. For this reason, a simple statistical data treatment (R-mode Factor Analysis) was performed on fifteen and nineteen samples of sediment-hosted and volcanic-hosted Mn ore respectively, in order to identify both the mineral phases trapping trace

The physical hydrogeology of ore deposits

Science.gov (United States)

Ingebritsen, Steven E.; Appold, M.S.

2012-01-01

Hydrothermal ore deposits represent a convergence of fluid flow, thermal energy, and solute flux that is hydrogeologically unusual. From the hydrogeologic perspective, hydrothermal ore deposition represents a complex coupled-flow problem—sufficiently complex that physically rigorous description of the coupled thermal (T), hydraulic (H), mechanical (M), and chemical (C) processes (THMC modeling) continues to challenge our computational ability. Though research into these coupled behaviors has found only a limited subset to be quantitatively tractable, it has yielded valuable insights into the workings of hydrothermal systems in a wide range of geologic environments including sedimentary, metamorphic, and magmatic. Examples of these insights include the quantification of likely driving mechanisms, rates and paths of fluid flow, ore-mineral precipitation mechanisms, longevity of hydrothermal systems, mechanisms by which hydrothermal fluids acquire their temperature and composition, and the controlling influence of permeability and other rock properties on hydrothermal fluid behavior. In this communication we review some of the fundamental theory needed to characterize the physical hydrogeology of hydrothermal systems and discuss how this theory has been applied in studies of Mississippi Valley-type, tabular uranium, porphyry, epithermal, and mid-ocean ridge ore-forming systems. A key limitation in the computational state-of-the-art is the inability to describe fluid flow and transport fully in the many ore systems that show evidence of repeated shear or tensional failure with associated dynamic variations in permeability. However, we discuss global-scale compilations that suggest some numerical constraints on both mean and dynamically enhanced crustal permeability. Principles of physical hydrogeology can be powerful tools for investigating hydrothermal ore formation and are becoming increasingly accessible with ongoing advances in modeling software.

Soil Contamination at the Historical Zn-Pb Ore Mining Sites (Southern Poland

Directory of Open Access Journals (Sweden)

Aleksander-Kwaterczak U.

2013-04-01

Full Text Available Results of metals analyses in soil profiles sampled at two 18/19th century mine shafts of the Trzebinia lead-zinc ore mining region in southern Poland are presented. Waste dump sites located at these shafts exhibit initial pedogenesis with clear differences in zinc and cadmium content between soil horizons which changes in depth across each of the investigated dump. The highest metal concentrations occur in horizons containing excavated ore-bearing Triassic dolomites, soils buried beneath are less polluted whereas, initial A0 soil horizons are virtually unpolluted. Relatively low downward metal migration in profiles to the horizons underlying the dumps is related to alkaline pH of soils. Migration appear to be important in the more acidic soils of outer zones in the two dump sites overgrown either with coniferous and deciduous trees.

Acid pre-treatment method for in situ ore leaching

International Nuclear Information System (INIS)

Mallon, R.G.; Braun, R.L.

1975-01-01

An acid leaching method is described for the recovery of a desired element from a subterranean rubblized body of primary ore containing the element and also having associated therewith a carbonate mineral wherein the rubblized ore body is flooded with an aqueous acidic solution in order to release carbon dioxide from the associated carbonate mineral. After a substantial portion of the available carbon dioxide is released and removed from the ore body, as by venting to the atmosphere, an oxidizing gas is introduced into the flooded, rubblized ore to oxidize the ore and form an acid leach solution effective in the presence of the dissolved oxidizing gas to dissolve the ore and cause the desired element to go into solution. The leach solution is then circulated to the surface where the metal values are recovered therefrom

Influence of ore processing activity on Hg, As and Sb contamination and fractionation in soils in a former mining site of Monte Amiata ore district (Italy).

Science.gov (United States)

Protano, Giuseppe; Nannoni, Francesco

2018-05-01

A geochemical study was carried out at the former Abbadia San Salvatore (ASS) mining site of the Monte Amiata ore district (Italy). Hg, As and Sb total contents and fractionation using a sequential extraction procedure were determined in soil and mining waste samples. Ore processing activities provided a different contribution to Hg contamination and concentration in soil fractions, influencing its behaviour as volatility and availability. Soils of roasting zone showed the highest Hg contamination levels mainly due to the deposition of Hg released as Hg 0 by furnaces during cinnabar roasting. High Hg contents were also measured in waste from the lower part of mining dump due to the presence of cinnabar. The fractionation pattern suggested that Hg was largely as volatile species in both uncontaminated and contaminated soils and mining waste, and concentrations of these Hg species increased as contamination increased. These findings were in agreement with the fact that the ASS mining site is characterized by high Hg concentrations in the air and the presence of Hg 0 liquid droplets in soil. Volatile Hg species were also prevalent in uncontaminated soils likely because the Monte Amiata region is an area characterized by anomalous fluxes of gaseous Hg from natural and anthropogenic inputs. At the ASS mining site soils were also contaminated by Sb, while As contents were comparable with its local background in soil. In all soil and waste samples Sb and As were preferentially in residual fraction. Copyright © 2018 Elsevier Ltd. All rights reserved.

Chemical composition of hydrothermal ores from Mid-Okinawa trough and Suiyo Seamount determined by neutron activation analysis

International Nuclear Information System (INIS)

Noguchi, Takuroh; Taira, Naoto; Oomori, Tamotsu; Taira, Hatsuo; Tanahara, Akira; Takada, Jitsuya

2007-01-01

Neutron activation analysis of 13 hydrothermal ore samples (70 subsamples) collected from the Mid-Okinawa Trough and Suiyo Seamount revealed higher contents of precious metal such as Au and Ag, and those of As, Sb, Ga, and Hg than those from mid-ocean ridge hydrothermal systems. In addition, the Mid-Okinawa Trough samples were richer in Ag and Sb than those from the Suiyo Seamount. The geochemical differences among these hydrothermal ore deposits are regarded as reflecting both differences in the chemical composition of the hosted magma of hydrothermal system and the abundance of sediments that is reacted with hydrothermal fluids. (author)

Experimental study on bio-leaching of high sulphuric acid consumption uranium ore by adding sulphide

International Nuclear Information System (INIS)

Meng Yunsheng; Zheng Ying; Liu Hui; Cheng Hao; Zhou Lei; Liu Chao; Fan Baotuan; Li Jianhua

2012-01-01

In order to decrease acid consumption and increase leaching rate, an experiment on bio-leach-ing of low grade uranium ore by adding sulphide was done. Compared with conventional leaching method, the leaching rate of uranium is improved by 3% and the leaching period was reduced to 60 days from 90 days by bio-leaching method of adding sulphide. In order to decrease acid consumption with bio-leaching by adding sulphide obviously, robust bacteria to sulphide should be chosen. (authors)

Characteristics of sandstone-type uranium mineralization and ore-controlling factors in Wukurqi ore district at southern margin of Yili basin, Xinjiang

International Nuclear Information System (INIS)

Li Xigen

2002-01-01

With the theories of hydrogenic uranium deposit in the nineties, Wukurqi ore district as a new area was found by the regional prediction and prospecting. Specially, through uranium ore prospecting of about three years, certain prospective reserves are generally controlled in the area. These reserves are hosted in V cyclothem of Middle-Lower Jurassic series, and some prospective reserves are hosted in II and VII cyclothems. By analyzing and summarizing characteristics of sandstone-type uranium mineralization and its ore-controlling factors in Wukurqi ore district, the author provides a foundation for developing further prospecting in this area

Geostatistical Approach to Estimating the Gold Ore Characteristics and Gold Reserves: A Case Study Daksa Area, Quang Nam Province, Viet Nam

Science.gov (United States)

Luan Truong, Xuan; Luong Le, Van; Quang Truong, Xuan

2015-04-01

Daksa gold deposit is the biggest gold deposits in Vietnam. The Daksa geological structure complicated, distributed mainly metamorphosed sedimentary NuiVu formation (PR3-?1nv2). The sulfide gold ore bodies distributed in quartz schist, quartz - biotite related to faut and distribution wing anticline. The gold ore bodies form circuits, network circuits, circuits lenses; fill the cup surface layer of the developing northeast - southwest; is the less than or west longitude north - SE. The results show that, Au and accompanying elements (Ag, Pb and Zn) have correlated pretty closely. All of its consistent with the logarithmic distribution standard, in accordance with the law of distribution of content mineral rare. The structure functions have nugget effect and spherical models with show that Au and accompanying elements special variation are changes. Au contents shown local anisotropy, no clearly anisotropy (K=1,17) and weakly anisotropy (K=1,4). Intensity mineralization of the ore bodies are quite high with demand spherical conversion coefficient ranging from 0.49 to 0.75 and from 0.66 to 0.97 (for other body). With nugget effects, ore bodies shown that it is consistent with mineralization in the ore bodies study, ore erasable, micro vein, infilling fractures in quartz vein. All of variogram presents local anisotropy, indicated gold mineralization at study area has least two-mineralization stages, consistent with the analysis of mineralography samples. By the results of the structure function study, the authors present the system optimization for exploration deposit and used to evaluate gold reserves by Ordinary Kriging. High accuracy of Kriging estimation results are expressed in the minimum Kriging variance, by compare the results calculated by some other methods (such as distance inverse weighting method, ..) and specially compare to the results of a some blocks have been exploited. Key words: Geostat and gold deposits VN. Daksa and gold mineralization. Geostat

Komatiites and nickel sulfide ores of the Black Swan area, Yilgarn Craton, Western Australia. 2: Geology and genesis of the orebodies

Science.gov (United States)

Dowling, S. E.; Barnes, S. J.; Hill, R. E. T.; Hicks, J. D.

2004-11-01

The Black Swan Ultramafic Succession hosts a number of magmatic Fe Ni Cu PGE sulfide ore shoots, ranging from high grade massive ore to low grade disseminated sulfides. Of these, the most economically significant is the Silver Swan massive sulfide orebody, associated with the basal contact of the succession. The deposit varies in thickness between 5 and 20 m, reaches a N S strike length of 75 m, extends for at least 1.2 km of vertical plunge and is open at depth. Overlying matrix (net-textured) ore is rare. Inclusions of dacite are abundant within the lower 5 m of the massive sulfide. They range from angular fragments through smooth sinuous and plumose morphologies to fine lace-like intergrowths with the sulfide matrix, and comprise variable proportions of cores of porphyritic dacite and carapaces with skeletal plagioclase phenocrysts. Dynamic crystallisation and kinetic melting textures in the carapaces indicate that the inclusions have been heated to various temperatures, some well above their liquidus temperature. The composition of the inclusions ranges from a perfect match with the immediate footwall dacites to mixtures of dacite with up to 30% komatiite. The consistent thickness of the inclusion-bearing basal layer within the massive sulphide is interpreted as the extent of 3-D physical connectivity between the inclusions and a partially molten underlying hybrid layer. Primary contacts between the Silver Swan massive sulfide orebody and overlying ultramafic rocks are marked by thin rinds containing coarse-grained chevron-textured chromites with skeletal textures. Compositions of these chromites match those from Kambalda, Perseverance and other localities, and are inconsistent with a metamorphic origin. They are interpreted as markers of primary magmatic contacts. The combination of this feature with the general paucity of matrix ore implies that the massive ore accumulated and solidified before the accumulation of the overlying thick sequence of olivine

Pleistocene apparent ages by U-Pb isotope and U-series methods for uranium ore in Dakota Sandstone near Gallup, New Mexico

International Nuclear Information System (INIS)

Ludwig, K.R.; Szabo, B.J.; Granger, H.C.

1977-01-01

Radiometric dates of a high-grade uranium ore from the Hogback No. 4 mine in Dakota Sandstone near Gallup, N. Mex., indicate a late Pleistocene age of mineralization. The 206 Pb/ 238 U and 207 Pb/ 235 U apparent ages of about 70,000 y and 100,000 y, respectively, are discordant, but are in broad agreement with the discordant 230 Th/ 238 U and 230 Pa/ 235 U apparent ages of 130,000 y and 78,000 y, respectively. Although it is not clear how the analyzed sample relates to the main period of mineralization at this mine, these dates are consistent with previous age limits suggested for Dakota Sandstone uranium ores

XPS and FTIR spectroscopic study on microwave treated high phosphorus iron ore

Energy Technology Data Exchange (ETDEWEB)

Omran, Mamdouh, E-mail: mamdouh.omran@oulu.fi [Process Metallurgy Research Group, Faculty of Technology, University of Oulu (Finland); Mineral Processing and Agglomeration Lab, Central Metallurgical Research and Development Institute, Cairo (Egypt); Fabritius, Timo [Process Metallurgy Research Group, Faculty of Technology, University of Oulu (Finland); Elmahdy, Ahmed M.; Abdel-Khalek, Nagui A. [Mineral Processing and Agglomeration Lab, Central Metallurgical Research and Development Institute, Cairo (Egypt); El-Aref, Mortada; Elmanawi, Abd El-Hamid [Geology Department, Faculty of Science, Cairo University, Giza 12613 (Egypt)

2015-08-01

Highlights: • The effect of microwave radiation on structure and chemical state of high phosphorus iron ore was studied. • FTIR analyses showed that after microwave radiation the functional chemical groups of phosphorus bearing minerals (fluorapatite) dissociated. • High resolution XPS analyses of Fe 2p peaks showed that after microwave radiation a portion of Fe(+III) was reduced to Fe(+II). • Microwave radiation had a positive effect on the magnetic properties of iron oxide, through formation of ferromagnetic phases. - Abstract: A growing interest in microwave heating has emerged recently. Several potential microwave applications regarding minerals’ processing have been investigated. This paper investigates the effect of microwave radiation on Egyptian high phosphorus iron ore. Three different iron ore samples have varying Fe{sub 2}O{sub 3} and P{sub 2}O{sub 5} contents and mineralogical textures were studied. A comparative study has been carried out between untreated and microwave treated iron ore. XRD and FTIR analyses showed that after microwave radiation the crystallinity of iron bearing minerals (hematite) increased, while the functional chemical groups of phosphorus bearing minerals (fluorapatite) and other gangues dissociated. High resolution XPS analyses of Fe 2p peaks showed that after microwave radiation a portion of Fe(+III) was reduced to Fe(+II). This means that after microwave radiation iron oxide (hematite, Fe{sup 3+}) transformed into more magnetic phase. The results indicated that microwave radiation had a positive effect on the magnetic properties of iron oxide, through formation of ferromagnetic phases.

Summary of the mineralogy of the Colorado Plateau uranium ores

Science.gov (United States)

Weeks, Alice D.; Coleman, Robert Griffin; Thompson, Mary E.

1956-01-01

In the Colorado Plateau uranium has been produced chiefly from very shallow mines in carnotite ores (oxidized vanadiferous uranium ores) until recent deeper mining penetrated black unoxidized ores in water-saturated rocks and extensive exploration has discovered many deposits of low to nonvanadiferous ores. The uranium ores include a wide range from highly vanadiferous and from as much as one percent to a trace of copper, and contain a small amount of iron and traces of lead, zinc, molybdenum, cobalt, nickel, silver, manganese, and other metals. Recent investigation indicates that the carnotite ores have been derived by progressive oxidation of primary (unoxidized) black ores that contain low-valent uranium and vanadium oxides and silicates. The uranium minerals, uraninite and coffinite, are associated with coalified wood or other carbonaceous material. The vanadium minerals, chiefly montroseite, roscoelite, and other vanadium silicates, occur in the interstices of the sandstone and in siltstone and clay pellets as well as associated with fossil wood. Calcite, dolomite, barite and minor amounts of sulfides, arsenides, and selenides occur in the unoxidized ore. Partially oxidized vanadiferous ore is blue black, purplish brown, or greenish black in contrast to the black or dark gray unoxidized ore. Vanadium combines with uranium to form rauvite. The excess vanadium is present in corvusite, fernandinite, melanovanadite and many other quadrivalent and quinquevalent vanadium minerals as well as in vanadium silicates. Pyrite and part or all of the calcite are replaced by iron oxides and gypsum. In oxidized vanadiferous uranium ores the uranium is fixed in the relatively insoluble minerals carnotite and tyuyamunite, and the excess vanadium commonly combines with one or more of the following: calcium, sodium, potassium, magnesium, aluminum, iron, copper, manganese, or barium, or rarely it forms the hydrated pentoxide. The relatively stable vanadium silicates are little

Composite correlation filter for O-ring detection in stationary colored noise

Science.gov (United States)

Hassebrook, Laurence G.

2009-04-01

O-rings are regularly replaced in aircraft and if they are not replaced or if they are installed improperly, they can result in catastrophic failure of the aircraft. It is critical that the o-rings be packaged correctly to avoid mistakes made by technicians during routine maintenance. For this reason, fines may be imposed on the o-ring manufacturer if the o-rings are packaged incorrectly. That is, a single o-ring must be packaged and labeled properly. No o-rings or more than one o-ring per package is not acceptable. We present an industrial inspection system based on real-time composite correlation filtering that has successfully solved this problem in spite of opaque paper o-ring packages. We present the system design including the composite filter design.

Significance of mineralogy in the development of flowsheets for processing uranium ores

International Nuclear Information System (INIS)

1980-01-01

This report has been prepared from material developed at and subsequent to a consultants' meeting held in Vienna in January 1978. The main purpose of the meeting was to prepare a document in the form of a guide for planning and developing treatment flowsheets for uranium ore processing. It was apparent that ore mineralogy, analysed, described and interpreted in ways most meaningful to the metallurgist, is the most essential information required for forming the basis of such planning. This topic, here termed metallurgical mineralogy, is therefore a major theme of this publication. In preparing the report the Agency has borne in mind the important need to impart the experience and knowledge gained in the more developed countries to those who are in the early stages of exploiting their uranium resources. The contents may be criticized as lacking, in some respects, the requisite depth and detail of treatment. The Agency and the consultants are conscious of the need to expand the information in a number of ways. However, the report is presented in its present form in the belief that, as the first attempt to correlate, on a world-wide basis, ore type with processing, it will be considered as a useful basis for future development of these themes

Ore potential of basic rocks in Finland

International Nuclear Information System (INIS)

Reino, J.; Ekberg, M.; Heinonen, P.; Karppanen, T.; Hakapaeae, A.; Sandberg, E.

1993-02-01

The report is associated with a study programme on basic rocks, which has the aim to complement the preliminary site investigations on repository for TVO's (Teollisuuden Voima Oy) spent nuclear fuel. The report comprises a mining enterprise's view of the ore potential of basic plutonic rocks in Finland. The ores associated with basic plutonic rocks are globally known and constitute a significant share of the global mining industry. The ores comprise chromium, vanadium-titanium-iron, nickel-copper and platinum group element ores. The resources of the metals in question and their mining industry are examined globally. A review of the use of these metals in the industry is presented as well. General factors affecting the mining industry, such as metal prices, political conjunctures, transport facilities, environmental requirements and raw material sources for the Finnish smelters have been observed from the point of view of their future effect on exploration activity and industrial development in Finland. Information on ores and mineralizations associated with Finnish basic rocks have been compiled in the report. The file comprises 4 chromium occurrences, 8 vanadium-titanium-iron occurrences, 13 PGE occurrences and 38 nickel-copper occurrences

Testing of X-ray radiometric enrichnment of polymetallic ores

International Nuclear Information System (INIS)

Eliseev, N.I.; Panova, N.I.; Kirbitova, N.V.; Shramm, E.O.; Efremov, Yu.G.

1987-01-01

Testing of X-ray radiometric method of sorting of polymetallic ores using the developed X-ray radiometric device was conducted. It was shown that introduction of preliminary concentration at the factory made the method of fragment separation to be the perspective one, enabling to elevate the factory production with respect to commercial ore and reduce the cost of ore processing. In the case of preliminary concentration, conducted at the mine, it is advisable to perform ore sorting in the flow formed to monolayer

X-ray fluorescence separation of pure lead-zinc ores

International Nuclear Information System (INIS)

Lapshin, S.A.; Filippov, O.K.; Khachatryan, L.S.; Rudnev, B.P.

1987-01-01

To evaluate the influence of the previous concentration of polymetallic ores by the radiometric separation method on indices of flotation and gravitation enrichments, investigations were carried out using ore sample (1.94%Pb, 1.13% Zn) from a lead-zink ore deposit. It is shown that the results obtained on the enrichment of the ore and products of X-ray radiometric separation are similar. However previous removal (up to 40%) of dead rock permits to reduce sharply grinding and transpot costs

A Comparative Analysis of Uranium Ore using Laser Fluorimetric and gamma Spectrometry Techniques

International Nuclear Information System (INIS)

Madbouly, M.; Nassef, M. H.; El-Mongy, S.A.; Diab, A.M.

2009-01-01

A developed chemical separation method was used for the analysis of uranium in a standard U-ore (IAEA-RGU-1) by LASER fluorimetric technique. The non-destructive gamma assay technique was also applied to verify and compare the uranium content analyzed using laser technique. The results of the uranium analysis obtained by laser fluorimetry were found to be in the range of 360 - 420 μg/g with an average value of 390 μg/g. The bias between the measured and the certified value does not exceed 9.9%. For gamma-ray spectrometric analysis, the results of the measured uranium content were found to be in the range of 393.8 - 399.4 μg/g with an average value of 396.3 μg/g. The % difference in the case of γ- assay was 1.6 %. In general, the methods of analysis used in this study are applicable for a precise determination of uranium. It can be concluded that, laser analysis is preferred for assay of uranium ore due to the required small sample weight, the low time of sample preparation and cost of analysis.

Sintering-alkaline processing of borosilicate ores of Tajikistan

International Nuclear Information System (INIS)

Nazarov, F.A.

2018-01-01

The aim of the work is to study the processes of decomposition of boron-containing ore by sintering with NaOH, finding the optimal parameters of the decomposition process, studying the kinetics of processes and developing the technological foundations for ore processing. The processes of borosilicate ore processing were studied by sintering with NaOH. Possible mechanisms of chemical reactions of the process of sintering-alkaline decomposition of boron-containing ore are established, the results of which are substantiated by physicochemical methods of analysis. A principal technological scheme for processing of borosilicate ores by a sintering-alkaline method has been developed. In the first chapter, data on alkaline and caking processes for processing boron-containing and aluminium comprising raw materials are available in the literature. Based on this, the directions of our own research are outlined. The second chapter is devoted to the study of the chemical and mineralogical compositions of borosilicate ores and their concentrates with the help of X-ray phase and chemical analysis methods, the stoichiometric calculation of the formation of aluminum, iron, and boron salts has been carried out, and a thermodynamic analysis of the processes of sintering borosilicate ores with alkali has been considered. The third chapter presents the results of a study of sintering-alkaline method of processing of initial borosilicate ore of the Ak-Arkhar Deposit and its concentrate without calcination and after calcination. The kinetics of sintering of borosilicate ores with sodium hydroxide was studied. The optimal conditions of borosilicate ore sintering before and after the preliminary calcination with alkali were determined. Optimal parameters of the sintering process have been found: sintering temperature 800-8500 deg C, duration of the process - 60 minutes, mass ratio of NaOH to raw materials 2: 1. The conditions for sintering of borosilicate concentrate with alkali have been

Multi-column bioleaching of a uranium ore

International Nuclear Information System (INIS)

Meng Yunsheng; Zheng Ying; Liu Hui; Cheng Hao

2014-01-01

The technology of bioleaching uranium ore can increase the uranium leaching rate and shorten the leaching uranium period, save consumption of acid and oxidant, lower production costs. An experiment on multi-column bioleaching of a uranium ore was done using mesophilic bacteria, the average uranium recovery of 90% was achieved in 39 days. Compared with traditional process, leaching period was shortened to 39 d from 59 d, acid consumption and liquid-solid ratio were also reduced. The results showed it is suitable to bioleach the uranium ore. (authors)

Iron from Zealandic bog iron ore -

DEFF Research Database (Denmark)

Lyngstrøm, Henriette Syrach

2011-01-01

og geologiske materiale, metallurgiske analyser og eksperimentel arkæologiske forsøg - konturerne af en jernproduktion med udgangspunkt i den sjællandske myremalm. The frequent application by archaeologists of Werner Christensen’s distribution map for the occurrence of bog iron ore in Denmark (1966...... are sketched of iron production based on bog iron ore from Zealand....

Chemical fingerprint of iron oxides related to iron enrichment of banded iron formation from the Cauê Formation - Esperança Deposit, Quadrilátero Ferrífero, Brazil: a laser ablation ICP-MS study

Directory of Open Access Journals (Sweden)

Lucilia Aparecida Ramos de Oliveira

Full Text Available Chemical signatures of iron oxides from dolomitic itabirite and high-grade iron ore from the Esperança deposit, located in the Quadrilátero Ferrífero, indicate that polycyclic processes involving changing of chemical and redox conditions are responsible for the iron enrichment on Cauê Formation from Minas Supergroup. Variations of Mn, Mg and Sr content in different generations of iron oxides from dolomitic itabirite, high-grade iron ore and syn-mineralization quartz-carbonate-hematite veins denote the close relationship between high-grade iron ore formation and carbonate alteration. This indicates that dolomitic itabirite is the main precursor of the iron ore in that deposit. Long-lasting percolation of hydrothermal fluids and shifts in the redox conditions have contributed to changes in the Y/Ho ratio, light/heavy rare earth elements ratio and Ce anomaly with successive iron oxide generations (martite-granular hematite, as well as lower abundance of trace elements including rare earth elements in the younger specularite generations.

Experiment on bio-leaching of associated molybdenum and uranium ore

International Nuclear Information System (INIS)

Zheng Ying; Fan Baotuan; Liu Jian; Meng Yunsheng; Liu Chao

2007-01-01

Column leaching experiment results on associated molybdenum uranium ore by bacteria (T. f) are introduced. The ore are leached for 210 days using bacteria domesticated to tolerate molybdenum, the leaching of uranium is of 98% and leaching of molybdenum is of 41%. Sulphuric acid produced by bio-oxidation of sulfides in ore can meet the demand of ore leaching. (authors)

NRC's limit on intake of uranium-ore dust

International Nuclear Information System (INIS)

McGuire, S.A.

1983-04-01

In 1960 the Atomic Energy Commission adopted an interim limit on the intake by inhalation of airborne uranium-ore dust. This report culminates two decades of research aimed at establishing the adequacy of that limit. The report concludes that the AEC underestimated the time that thorium-230, a constituent of uranium-ore dust, would remain in the human lung. The AEC assumed that thorium-230 in ore dust would behave like uranium with a 120-day biological half-life in the lung. This report concludes that the biological half-life is actually on the order of 1 year. Correcting the AEC's underestimate would cause a reduction in the permitted airborne concentration of uranium-ore dust. However, another factor that cancels the need for that reduction was found. The uranium ore dust in uranium mills was found to occur with very large particle sizes (10-micron activity median aerodynamic diameter). The particles are so large that relatively few of them are deposited in the pulmonary region of the lung, where they would be subject to long-term retention. Instead they are trapped in the upper regions of the respiratory tract, subsequently swallowed, and then rapidly excreted from the body through the gastrointestinal tract. The two effects are of about the same magnitude but in opposing directions. Thus the present uranium-ore dust intake limit in NRC regulations should provide a level of protection consistent with that provided for other airborne radioactive materials. The report recalculates the limit on intake of uranium-ore dust using the derived air concentrations (DAC) from the International Commission on Radiological Protection's recent Publication 30. The report concludes that the silica contained in uranium-ore dust is a greater hazard to workers than the radiological hazard

The Krásná Hora, Milešov, and Příčovy Sb-Au ore deposits, Bohemian Massif: mineralogy, fluid inclusions, and stable isotope constraints on the deposit formation

Science.gov (United States)

Němec, Matěj; Zachariáš, Jiří

2018-02-01

The Krásná Hora-Milešov and Příčovy districts (Czech Republic) are the unique examples of Sb-Au subtype orogenic gold deposits in the Bohemian Massif. They are represented by quartz-stibnite veins and massive stibnite lenses grading into low-grade, disseminated ores in altered host rocks. Gold postdates the stibnite and is often replaced by aurostibite. The ore zones are hosted by hydrothermally altered dikes of lamprophyres (Krásná Hora-Milešov) or are associated with local strike-slip faults (Příčovy). Formation of Sb-Au deposits probably occurred shortly after the main gold-bearing event (348-338 Ma; Au-only deposits) in the central part of the Bohemian Massif. Fluid inclusion analyses suggest that stibnite precipitated at 250 to 130 °C and gold at 200 to 130 °C from low-salinity aqueous fluids. The main quartz gangue hosting the ore precipitated from the same type of fluid at about 300 °C. Early quartz-arsenopyrite veins are not associated with the Sb-Au deposition and formed from low-salinity, aqueous-carbonic fluid at higher pressure and temperature ( 250 MPa, 400 °C). The estimated oxygen isotope composition of the ore-bearing fluid (4 ± 1‰ SMOW; based on post-ore calcite) suggests its metamorphic or mixed magmatic-metamorphic origin and excludes the involvement of meteoric water. Rapid cooling of warm hydrothermal fluids reacting with "cold" host rock was probably the most important factor in the formation of both stibnite and gold.

Collective sulphide flotation of the polymetallic molybdenic ore

International Nuclear Information System (INIS)

Mazanek, C.; Maselko, J.; Rycerz, L.

1980-01-01

Results of investigations on polymetallic molybdenic ore are presented. The useful minerals of this ore are as follows: molybdenite, sphalerite, galena and chalcopyrite whereas quartz, feldspars, chlorite and sericite are barren rocks. The flotation process parameters are established i.e. the consumption of flotation reagents, the flotation time and the most advantageous grain composition of the ore submitted to flotation. Taking into consideration the established parameters, a collective sulphide flotation of ore and a control flotation of wastes were carried out. The obtained concentrate was submitted to a single cleaning flotation whereby a concentrate was obtained containing: 4,65% Mo, 2,51% Cu, 0,9% Zn, 0,69% Pb, and 1,4% Bi. (author)

The applications of microwave energy to improve grindability and extraction of gold ores

Energy Technology Data Exchange (ETDEWEB)

Huang, J.H

2000-10-01

In this study, the applications of microwave energy in gold ore processing were investigated. An investigation of microwave heating characteristics indicated that the heating rate of an ore was not only related to the applied microwave field, but also to the mineralogy of the ore. Heating rate and the difference between the bulk temperature of an ore and the local temperature of high dielectric loss minerals increased with applied microwave power level, the content of high dielectric loss minerals, the particle size of the ore and the disseminated high dielectric loss minerals. The relationship between heating rate and surrounding environment is also discussed in this study. Investigations indicated that the microwave exposure could reduce the grindability of ores. For the Lihir gold ore, a decrease of 11% in the comparative grindability was obtained when it was exposed to 1500W microwave energy for 8 minutes. The decrease in grinding resistance resulted predominantly from the fractures induced by thermal stresses and differential thermal expansion of mineral phases during microwave heating. Experimental results showed that marcasite and pyrite could be decomposed into elemental sulphur and pyrrhotite-like Fe-S phases in an inert atmosphere, or oxidised into a porous hematite (Fe{sub 2}O{sub 3}) in an air atmosphere when they were exposed to microwaves. Microwave power had a significant impact on the decomposition of pyrite and marcasite. Marcasite was more readily decomposed than pyrite at the same exposure conditions. Scanning electron microscope (SEM), optical microscope, and X-ray diffraction results indicated that the alterations during microwave treatment were complex. Some intermediate products (e.g. Fe{sub (1-x)}S) were formed before the sulphides were completely oxidised into hematite (Fe{sub 2}O{sub 3}). Oxidation developed from the surfaces into the cores of the microwaved particles. Metallic particles were also formed during microwave exposure. Lihir

The applications of microwave energy to improve grindability and extraction of gold ores

International Nuclear Information System (INIS)

Huang, J.H.

2000-10-01

In this study, the applications of microwave energy in gold ore processing were investigated. An investigation of microwave heating characteristics indicated that the heating rate of an ore was not only related to the applied microwave field, but also to the mineralogy of the ore. Heating rate and the difference between the bulk temperature of an ore and the local temperature of high dielectric loss minerals increased with applied microwave power level, the content of high dielectric loss minerals, the particle size of the ore and the disseminated high dielectric loss minerals. The relationship between heating rate and surrounding environment is also discussed in this study. Investigations indicated that the microwave exposure could reduce the grindability of ores. For the Lihir gold ore, a decrease of 11% in the comparative grindability was obtained when it was exposed to 1500W microwave energy for 8 minutes. The decrease in grinding resistance resulted predominantly from the fractures induced by thermal stresses and differential thermal expansion of mineral phases during microwave heating. Experimental results showed that marcasite and pyrite could be decomposed into elemental sulphur and pyrrhotite-like Fe-S phases in an inert atmosphere, or oxidised into a porous hematite (Fe 2 O 3 ) in an air atmosphere when they were exposed to microwaves. Microwave power had a significant impact on the decomposition of pyrite and marcasite. Marcasite was more readily decomposed than pyrite at the same exposure conditions. Scanning electron microscope (SEM), optical microscope, and X-ray diffraction results indicated that the alterations during microwave treatment were complex. Some intermediate products (e.g. Fe (1-x) S) were formed before the sulphides were completely oxidised into hematite (Fe 2 O 3 ). Oxidation developed from the surfaces into the cores of the microwaved particles. Metallic particles were also formed during microwave exposure. Lihir gold ore, in which

Origin of ores of endogeneous uranium ore deposits

International Nuclear Information System (INIS)

Kasanskij, V.I.; Laverov, N.P.; Tugarinov, A.I.

1976-01-01

The consideration mainly includes those endogenous uranium ore deposits of which more exact data are available, such as precambrian ones in areas of proto-activated old platforms, deposits of palaeozoic fold areas, and mesozoic deposits in areas of tectonic-magnetic activation. Their genesis and typical characters are mentioned and conclusions on the general distribution of the deposits are drawn. (author)

Mining of sedimentary-type ore deposits