The 2-D lattice theory of Flower Constellations

Science.gov (United States)

Avendaño, Martín E.; Davis, Jeremy J.; Mortari, Daniele

2013-08-01

The 2-D lattice theory of Flower Constellations, generalizing Harmonic Flower Constellations (the symmetric subset of Flower Constellations) as well as the Walker/ Mozhaev constellations, is presented here. This theory is a new general framework to design symmetric constellations using a 2× 2 lattice matrix of integers or by its minimal representation, the Hermite normal form. From a geometrical point of view, the phasing of satellites is represented by a regular pattern (lattice) on a two-Dimensional torus. The 2-D lattice theory of Flower Constellations does not require any compatibility condition and uses a minimum set of integer parameters whose meaning are explored throughout the paper. This general minimum-parametrization framework allows us to obtain all symmetric distribution of satellites. Due to the J_2 effect this design framework is meant for circular orbits and for elliptical orbits at critical inclination, or to design elliptical constellations for the unperturbed Keplerian case.

Indigenous lunar construction materials

Science.gov (United States)

Rogers, Wayne P.; Sture, Stein

1991-01-01

The utilization of local resources for the construction and operation of a lunar base can significantly reduce the cost of transporting materials and supplies from Earth. The feasibility of processing lunar regolith to form construction materials and structural components is investigated. A preliminary review of potential processing methods such as sintering, hot-pressing, liquification, and cast basalt techniques, was completed. The processing method proposed is a variation on the cast basalt technique. It involves liquification of the regolith at 1200-1300 C, casting the liquid into a form, and controlled cooling. While the process temperature is higher than that for sintering or hot-pressing (1000-1100 C), this method is expected to yield a true engineering material with low variability in properties, high strength, and the potential to form large structural components. A scenario for this processing method was integrated with a design for a representative lunar base structure and potential construction techniques. The lunar shelter design is for a modular, segmented, pressurized, hemispherical dome which could serve as habitation and laboratory space. Based on this design, estimates of requirements for power, processing equipment, and construction equipment were made. This proposed combination of material processing method, structural design, and support requirements will help to establish the feasibility of lunar base construction using indigenous materials. Future work will refine the steps of the processing method. Specific areas where more information is needed are: furnace characteristics in vacuum; heat transfer during liquification; viscosity, pouring and forming behavior of molten regolith; design of high temperature forms; heat transfer during cooling; recrystallization of basalt; and refinement of estimates of elastic moduli, compressive and tensile strength, thermal expansion coefficient, thermal conductivity, and heat capacity. The preliminary

Construction materials and Radon

International Nuclear Information System (INIS)

Paschuk, Sergei A.; Correa, Janine Nicolosi; Loriane, Fior; Schelin, Hugo R.; Pottker, Fabiana; Paula Melo, Vicente de

2008-01-01

Full text: Current studies have been performed with the aim to find the correlation of radon concentration in the air and used construction materials. At the first stage of the measurements different samples of materials used in civil construction were studied as a source of radon in the air and at the second step it was studied the radon infiltration insulation using different samples of finishing materials. For 222 Rn concentration measurements related to different construction materials as well as for the studies of radon emanation and its reduction, the sealed cell chambers, of approximately 60 x 60cm 2 , have been built using the ceramic and concrete blocks. This construction has been performed within protected and isolated laboratory environment to maintain the air humidity and temperature stable. These long term measurements have been performed using polycarbonate alpha track passive detectors. The exposure time was set about 15 days considering previous calibration performed at the Institute of Radiation Protection and Dosimetry (IRD/CNEN), where the efficiency of 70% was obtained for the density of alpha particle tracks about 13.8 cm -2 per exposure day and per kBq/m 3 of radon activity concentration. The chemical development of alpha tracks has been achieved by electrochemical etching. The track identification and counting have been done using a code based on the MATLAB Image Processing Toolbox. The cell chambers have been built following four principle steps: 1) Assembling the walls using the blocks and mortar; 2) Plaster installation; 3) Wall surface finishing using the lime; 4) Wall surface insulation by paint. Making the comparison between three layers installed at the masonry walls from concrete and ceramic blocks, it could be concluded that only wall painting with acrylic varnish attended the expectation and reduced the radon emanation flow by the factor of 2.5 approximately. Studied construction materials have been submitted the instant

Frontier constellations

DEFF Research Database (Denmark)

Eilenberg, Michael

2014-01-01

expansion, population resettlement and securitization, and the confluence of these dynamic processes creates special frontier constellations. Through the case of the Indonesian-Malaysian borderlands, I explore how processes of frontier colonization through agricultural expansion have been a recurrent...

Open Sourcing Social Change: Inside the Constellation Model

Directory of Open Access Journals (Sweden)

Tonya Surman

2008-09-01

Full Text Available The constellation model was developed by and for the Canadian Partnership for Children's Health and the Environment. The model offers an innovative approach to organizing collaborative efforts in the social mission sector and shares various elements of the open source model. It emphasizes self-organizing and concrete action within a network of partner organizations working on a common issue. Constellations are self-organizing action teams that operate within the broader strategic vision of a partnership. These constellations are outwardly focused, placing their attention on creating value for those in the external environment rather than on the partnership itself. While serious effort is invested into core partnership governance and management, most of the energy is devoted to the decision making, resources and collaborative effort required to create social value. The constellations drive and define the partnership. The constellation model emerged from a deep understanding of the power of networks and peer production. Leadership rotates fluidly amongst partners, with each partner having the freedom to head up a constellation and to participate in constellations that carry out activities that are of more peripheral interest. The Internet provided the platform, the partner network enabled the expertise to align itself, and the goal of reducing chemical exposure in children kept the energy flowing. Building on seven years of experience, this article provides an overview of the constellation model, discusses the results from the CPCHE, and identifies similarities and differences between the constellation and open source models.

Sensor Webs to Constellations

Science.gov (United States)

Cole, M.

2017-12-01

Advanced technology plays a key role in enabling future Earth-observing missions needed for global monitoring and climate research. Rapid progress over the past decade and anticipated for the coming decades have diminished the size of some satellites while increasing the amount of data and required pace of integration and analysis. Sensor web developments provide correlations to constellations of smallsats. Reviewing current advances in sensor webs and requirements for constellations will improve planning, operations, and data management for future architectures of multiple satellites with a common mission goal.

Satellite constellation design and radio resource management using genetic algorithm.

OpenAIRE

Asvial, Muhamad.

2003-01-01

A novel strategy for automatic satellite constellation design with satellite diversity is proposed. The automatic satellite constellation design means some parameters of satellite constellation design can be determined simultaneously. The total number of satellites, the altitude of satellite, the angle between planes, the angle shift between satellites and the inclination angle are considered for automatic satellite constellation design. Satellite constellation design is modelled using a mult...

Sustainable construction : towards a strategic approach to construction material management for waste reduction

OpenAIRE

Abarca Guerrero, L.; Scheublin, F.J.M.; Egmond - de Wilde De Ligny, van, E.L.C.; Lambert, A.J.D.

2008-01-01

The construction sector plays a key role in shaping and developing the built environment. It also has an undisputed and significant impact on it due to the amounts of materials extracted and produced as waste. The construction industry has emphasized to recycling construction waste (CW), however, relatively less emphasis has been paid on construction waste minimization. CW reduction can be achieved through changes in design concepts, material and construction methods selection and material ma...

49 CFR 176.96 - Materials of construction.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Materials of construction. 176.96 Section 176.96 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... Requirements for Barges § 176.96 Materials of construction. Barges used to transport hazardous materials must...

Night sky a field guide to the constellations

CERN Document Server

Poppele, Jonathan

2009-01-01

Stargazing is among the most peaceful and inspiring outdoor activities. Night Sky, the award-winning book by Jonathan Poppele, makes it more fun than ever! Take a simple approach to finding 62 constellations by focusing on one constellation at a time, instead of attempting to study dizzying charts. Start with the easy-to-find constellations during each season and work toward the more difficult ones. Better yet, you'll learn how to locate any constellation in relation to the Big Dipper, the North Star and the top of the sky. With two ways to locate each constellation, you'll know where in the sky to look and what to look for! Along the way, you'll be introduced to mythology, facts and tidbits, as well as details about the planets, solar system and more! As an added bonus, the book comes with a red-light flashlight for night reading.

Aquarius-Pisces Constellation Boundary Update

Science.gov (United States)

Durst, Steve

2017-06-01

Observation, mapping and study of Galaxy Stars has provided humanity direction, foundation, clarity and understanding through the ages.Human civilization advances itself using increasing intelligence and knowledge to develop tools and know how, the science of constellation star maps included: All that has been created by humanity, is to serve humanity.When people continue to use constellation star maps that no longer serve people effectively, the maps are updated, as is now the Aquarius-Pisces Constellation Boundary Update (APCBU), which marks 2000 as the year the Sun is in Aquarius at the vernal equinox.The 21st Century APCBU accounts for and incorporates science factors of precession, relativity and galacticity for professional astronomers, and social imperatives of increasing freedom, liberation and egalitarian culture for the 7.5 billion people of Earth.Twenty years into this first century of a new millennium and a new age is an effective time for an APCBU of such elegant simplicity that it changes less than 0.1% of the area of the IAU 1930 official constellation map, which marks 2597 about the year the Sun is in Aquarius at the time of the vernal equinox.The 21st Century APCBU results provide clarity and direction for humanity's next 2,000 years, if not 10,000 or 12,000 years, and advance the official astronomy / science start of the Aquarius Age -- long anticipated, desired, and imperative, especially in America -- by some 600 years.How much attention is increasingly focused on this region of the sky -- such as the recent discovery of 7 Earth-like worlds orbiting the Trappist-1 star in the Aquarius constellation -- will be an epochal 21st Century phenomenon of human science, society, and starlife.

Crater Constellation

Science.gov (United States)

Murdin, P.

2000-11-01

(the Cup; abbrev. Crt, gen. Crateris; area 282 sq. deg.) A southern constellation which lies to the south-west of Virgo, and culminates at midnight in mid-March. It represents the cup of the god Apollo in Greek mythology (see Corvus). Its brightest stars were cataloged by Ptolemy (c. AD 100-175) in the Almagest....

Drug policy constellations: A Habermasian approach for understanding English drug policy.

Science.gov (United States)

Stevens, Alex; Zampini, Giulia Federica

2018-07-01

It is increasingly accepted that a view of policy as a rational process of fitting evidence-based means to rationally justified ends is inadequate for understanding the actual processes of drug policy making. We aim to provide a better description and explanation of recent English drug policy decisions. We develop the policy constellation concept from the work of Habermas, in dialogue with data from two contemporary debates in English policy; on decriminalisation of drug possession and on recovery in drug treatment. We collect data on these debates through long-term participant observation, stakeholder interviews (n = 15) and documentary analysis. We show the importance of social asymmetries in power in enabling structurally advantaged groups to achieve the institutionalisation of their moral preferences as well as the reproduction of their social and economic power through the deployment of policies that reflect their material interests and normative beliefs. The most influential actors in English drug policy come together in a 'medico-penal constellation', in which the aims and practices of public health and social control overlap. Formal decriminalisation of possession has not occurred, despite the efforts of members of a challenging constellation which supports it. Recovery was put forward as the aim of drug treatment by members of a more powerfully connected constellation. It has been absorbed into the practice of 'recovery-oriented' drug treatment in a way that maintains the power of public health professionals to determine the form of treatment. Actors who share interests and norms come together in policy constellations. Strategic action within and between constellations creates policies that may not take the form that was intended by any individual actor. These policies do not result from purely rational deliberation, but are produced through 'systematically distorted communication'. They enable the most structurally favoured actors to institutionalise

Guidebook to the Constellations Telescopic Sights, Tales, and Myths

CERN Document Server

Simpson, Phil

2012-01-01

This handbook is a guide to exploring the night sky and its wonderful telescopic sights. All eighty-eight officially recognized constellations in both hemispheres are presented in natural groups, related by their origin and location. The author, a former astronomy instructor and planetarium director, has for over thirty-five years, researched myths from all over the world to identify the most memorable stories which link multiple constellations in a single story. Thus, the interested observer may discover that it will be easier to use already known constellations to locate and remember new constellations. The author has found that showing each constellation figure with a simple line drawing is helpful for remembering each constellation. He includes photographs of many of the brighter celestial objects, as well as many accompanying drawings which illustrate how the telescopic views differ from the photographs. One way to use this handbook, which is useful to beginners as well as experienced astronomers, is to ...

23 CFR 633.207 - Construction labor and materials.

Science.gov (United States)

2010-04-01

... 23 Highways 1 2010-04-01 2010-04-01 false Construction labor and materials. 633.207 Section 633... OPERATIONS REQUIRED CONTRACT PROVISIONS Federal-Aid Contracts (Appalachian Contracts) § 633.207 Construction labor and materials. (a) Construction and materials shall be in accordance with the State highway...

[Materials for construction sector].

Science.gov (United States)

Macchia, C

2012-01-01

The construction sector is characterized by high complexity due to several factors. There are a lot of processes within the building sites and they need the use of different materials with the help of appropriate technologies. Traditional materials have evolved and diversified, meanwhile new products and materials appeared and still appear, offering services which meet user needs, but that often involve risks to the health of workers. Research in the field of materials, promoted and carried out at various levels, has led to interesting results, encoded in the form of rules and laws.

43 CFR 12.830 - Buy American Act-Construction materials.

Science.gov (United States)

2010-10-01

... 43 Public Lands: Interior 1 2010-10-01 2010-10-01 false Buy American Act-Construction materials... Assistance Programs Buy American Act-Construction Materials § 12.830 Buy American Act—Construction materials...—Construction Materials (a) The Buy American Act (41 U.S.C. 10) provides that the Government give preference to...

Influential Factors Affecting Materials Management in Construction Projects

Directory of Open Access Journals (Sweden)

Jusoh Zairra Mat

2017-12-01

Full Text Available Construction projects are more often than not plagued by poor performances such as delays, cost overrun, low productivity, construction wastes and compromised quality. Amongst the critical contributory factors of poor project performances, is the ineffectiveness of materials management occurring in the construction sites. Indeed, materials management is a very important component for construction projects. However, there are only limited numbers of research available regarding this topic. Thus, this research focuses its study on materials management, specifically in identifying the influential factors that affect materials management in the construction project activities. Literatures from books, journal articles and conference papers related to poor project performances and materials management have been reviewed. Consequently, this study sorted the salient influential factors and categorized them based on their specific group. Out of 47 factors identified, they are classified into 8 groups. They are (1 site condition; (2 planning and handling on site; (3 management; (4 materials; (5 supplier and manufacturer default; (6 transportation; (7 contractual; and (8 governmental interferences. In conclusion, this study contends that by identifying the influential factors affecting materials management, it will help construction players to avoid the occurrence of those factors and will minimize the negative impacts on the overall performance of construction projects. Hence, the handling-over of project will be according to schedule and not delayed by materials mismanagement.

46 CFR 154.1702 - Materials of construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Materials of construction. 154.1702 Section 154.1702... § 154.1702 Materials of construction. When Table 4 references one of the following paragraphs in this section, the materials in the referenced paragraph must not be in components that contact the cargo liquid...

Nondestructive evaluation ultrasonic methods for construction materials

International Nuclear Information System (INIS)

Chilibon, I.; Zisu, T.; Raetchi, V.

2002-01-01

The paper presents some ultrasonic methods for evaluation of physical-mechanical properties of construction materials (bricks, concrete, BCA), such as: pulse method, examination methods, and direct measurement of the propagation velocity and impact-echo method. Utilizing these nondestructive evaluation ultrasonic methods it can be determined the main material parameters and material characteristics (elasticity coefficients, density, propagation velocity, ultrasound attenuation, etc.) of construction materials. These method are suitable for construction materials because the defectoscopy methods for metallic materials cannot be utilized, due to its rugged and non-homogeneous structures and grate attenuation coefficients of ultrasound propagation through materials. Also, the impact-echo method is a technique for flaw detection in concrete based on stress wave propagation. Studies have shown that the impact-echo method is effective for locating voids, honeycombing, delaminating, depth of surface opening cracks, and measuring member thickness

Construction materials, monuments and environment

Science.gov (United States)

Prikryl, R.; Siegesmund, S.; Török, A.; Brimblecombe, P.; Gomez-Heras, M.

2012-04-01

Construction materials (natural stone, aggregates, bricks, cement, lime, mortar, etc.) form a wide and heterogeneous group both from the genetic and technological point of view. These materials deserve attention from the scientific community due to their long-term use, importance for society and sensitivity to the environment. Most geomaterials have also been used in important monuments designated as a part of the World Cultural Heritage and/or make part of national monuments. Despite of the wide-ranges of studies and our rapidly increasing understanding of material behaviour, our knowledge is still rather limited in many aspects. This concerns the characterisation of traditional raw materials, the knowledge of their processing and use, and/or durability and compatibility assessment. The exploitation and sustainable use of these materials are also new and emerging challenges in the modern society. The use of local materials for monuments can be considered as a part of our cultural and technological heritage, which has, however, significantly deteriorated during the past several decades. This paper summarizes the general topics related to a modern analysis of traditional construction materials derived from the Earth, and on the characteristic aspects of the behaviour of these materials on selected monuments.

Level-2 product generation for the Swarm satellite constellation mission

DEFF Research Database (Denmark)

Olsen, Poul Erik Holmdahl; Tøffner-Clausen, Lars; Olsen, Nils

In order to take advantage of the unique constellation aspect of ESA's Swarm constellation mission, considerably advanced data analysis tools have been developed. The Swarm ESL/SCARF (Satellite Constellation Application and Research Facility), a consortium of several research institutions, derives...

Self-Organized Construction with Continuous Building Material

DEFF Research Database (Denmark)

Heinrich, Mary Katherine; Wahby, Mostafa; Divband Soorati, Mohammad

2016-01-01

Self-organized construction with continuous, structured building material, as opposed to modular units, offers new challenges to the robot-based construction process and lends the opportunity for increased flexibility in constructed artifact properties, such as shape and deformation. As an example...... investigation, we look at continuous filaments organized into braided structures, within the context of bio-hybrids constructing architectural artifacts. We report the result of an early swarm robot experiment. The robots successfully constructed a braid in a self-organized process. The construction process can...... be extended by using different materials and by embedding sensors during the self-organized construction directly into the braided structure. In future work, we plan to apply dedicated braiding robot hardware and to construct sophisticated 3-d structures with local variability in patterns of filament...

46 CFR 164.006-3 - Construction, materials, and workmanship.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Construction, materials, and workmanship. 164.006-3..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL MATERIALS Deck Coverings for Merchant Vessels § 164.006-3 Construction, materials, and workmanship. (a) It is the intent of this specification to obtain a...

Identification of Key Indicators for Sustainable Construction Materials

Directory of Open Access Journals (Sweden)

Humphrey Danso

2018-01-01

Full Text Available Studies on sustainable construction materials are on the rise with their environmental, social, and economic benefits. This study identifies the key indicators for measuring sustainable construction materials. The design used for the study was that of a survey which relied on a questionnaire with five-point Likert scale to generate data for the analysis. For this purpose, 25 indicators from the three dimensions (environmental, social, and economic identified from the literature were presented to the respondents in a structured questionnaire, and responses were collected and analysed using SPSS. The study identified three key environmental indicators for measuring sustainable construction materials, and these indicators are human toxicity, climate change, and solid waste. Furthermore, adaptability, thermal comfort, local resources, and housing for all were identified as the four key social indicators for sustainable construction materials. In addition, maintenance cost, operational cost, initial cost, long-term savings, and life span were found to be the five key economic indicators for measuring sustainable construction materials. The study therefore suggests that these twelve indicators should be considered in future studies that seek to measure sustainable construction materials.

Precipitation from the GPM Microwave Imager and Constellation Radiometers

Science.gov (United States)

Kummerow, Christian; Randel, David; Kirstetter, Pierre-Emmanuel; Kulie, Mark; Wang, Nai-Yu

2014-05-01

Satellite precipitation retrievals from microwave sensors are fundamentally underconstrained requiring either implicit or explicit a-priori information to constrain solutions. The radiometer algorithm designed for the GPM core and constellation satellites makes this a-priori information explicit in the form of a database of possible rain structures from the GPM core satellite and a Bayesian retrieval scheme. The a-priori database will eventually come from the GPM core satellite's combined radar/radiometer retrieval algorithm. That product is physically constrained to ensure radiometric consistency between the radars and radiometers and is thus ideally suited to create the a-priori databases for all radiometers in the GPM constellation. Until a robust product exists, however, the a-priori databases are being generated from the combination of existing sources over land and oceans. Over oceans, the Day-1 GPM radiometer algorithm uses the TRMM PR/TMI physically derived hydrometer profiles that are available from the tropics through sea surface temperatures of approximately 285K. For colder sea surface temperatures, the existing profiles are used with lower hydrometeor layers removed to correspond to colder conditions. While not ideal, the results appear to be reasonable placeholders until the full GPM database can be constructed. It is more difficult to construct physically consistent profiles over land due to ambiguities in surface emissivities as well as details of the ice scattering that dominates brightness temperature signatures over land. Over land, the a-priori databases have therefore been constructed by matching satellite overpasses to surface radar data derived from the WSR-88 network over the continental United States through the National Mosaic and Multi-Sensor QPE (NMQ) initiative. Databases are generated as a function of land type (4 categories of increasing vegetation cover as well as 4 categories of increasing snow depth), land surface temperature and

Information-Theoretic Analysis of a Family of Improper Discrete Constellations

Directory of Open Access Journals (Sweden)

Ignacio Santamaria

2018-01-01

Full Text Available Non-circular or improper Gaussian signaling has proven beneficial in several interference-limited wireless networks. However, all implementable coding schemes are based on finite discrete constellations rather than Gaussian signals. In this paper, we propose a new family of improper constellations generated by widely linear processing of a square M-QAM (quadrature amplitude modulation signal. This family of discrete constellations is parameterized by κ , the circularity coefficient and a phase ϕ . For uncoded communication systems, this phase should be optimized as ϕ * ( κ to maximize the minimum Euclidean distance between points of the improper constellation, therefore minimizing the bit error rate (BER. For the more relevant case of coded communications, where the coded symbols are constrained to be in this family of improper constellations using ϕ * ( κ , it is shown theoretically and further corroborated by simulations that, except for a shaping loss of 1.53 dB encountered at a high signal-to-noise ratio (snr, there is no rate loss with respect to the improper Gaussian capacity. In this sense, the proposed family of constellations can be viewed as the improper counterpart of the standard proper M-QAM constellations widely used in coded communication systems.

Streamlining the Design Tradespace for Earth Imaging Constellations

Science.gov (United States)

Nag, Sreeja; Hughes, Steven P.; Le Moigne, Jacqueline J.

2016-01-01

Satellite constellations and Distributed Spacecraft Mission (DSM) architectures offer unique benefits to Earth observation scientists and unique challenges to cost estimators. The Cost and Risk (CR) module of the Tradespace Analysis Tool for Constellations (TAT-C) being developed by NASA Goddard seeks to address some of these challenges by providing a new approach to cost modeling, which aggregates existing Cost Estimating Relationships (CER) from respected sources, cost estimating best practices, and data from existing and proposed satellite designs. Cost estimation through this tool is approached from two perspectives: parametric cost estimating relationships and analogous cost estimation techniques. The dual approach utilized within the TAT-C CR module is intended to address prevailing concerns regarding early design stage cost estimates, and offer increased transparency and fidelity by offering two preliminary perspectives on mission cost. This work outlines the existing cost model, details assumptions built into the model, and explains what measures have been taken to address the particular challenges of constellation cost estimating. The risk estimation portion of the TAT-C CR module is still in development and will be presented in future work. The cost estimate produced by the CR module is not intended to be an exact mission valuation, but rather a comparative tool to assist in the exploration of the constellation design tradespace. Previous work has noted that estimating the cost of satellite constellations is difficult given that no comprehensive model for constellation cost estimation has yet been developed, and as such, quantitative assessment of multiple spacecraft missions has many remaining areas of uncertainty. By incorporating well-established CERs with preliminary approaches to approaching these uncertainties, the CR module offers more complete approach to constellation costing than has previously been available to mission architects or Earth

Research Progress of Building Materials Used in Construction Land

Science.gov (United States)

Niu, Yan

2018-01-01

Construction land preparation is an important aspect of land remediation project. The research of materials in the process of land improvement is the foundation and the core. Therefore, it is necessary to study the materials that may be involved in the process of building land preparation. In this paper, the research on the construction materials such as recycled concrete, geosynthetics, soil stabilizers, soil improvers, building insulation materials and inorganic fibrous insulation materials, which are commonly used in construction sites, is reviewed and discussed in this paper. Land remediation project involved in the construction of land materials to provide reference.

SATELLITE CONSTELLATION DESIGN PARAMETER

Indian Academy of Sciences (India)

First page Back Continue Last page Overview Graphics. SATELLITE CONSTELLATION DESIGN PARAMETER. 1. ORBIT CHARACTERISTICS. ORBITAL HEIGHT >= 20,000 KM. LONGER VISIBILITY; ORBITAL PERIOD. PERTURBATIONS(MINIMUM). SOLAR RADIATION PRESSURE (IMPACTS ECCENTRICITY); LUNI ...

48 CFR 25.605 - Evaluating offers of foreign construction material.

Science.gov (United States)

2010-10-01

... foreign construction material. 25.605 Section 25.605 Federal Acquisition Regulations System FEDERAL... American Act-Construction Materials 25.605 Evaluating offers of foreign construction material. (a) If the... evaluation factors to the offer incorporating the use of such foreign construction material as follows: (1...

Small Satellite Constellations for Geospace Sciences

Science.gov (United States)

Spence, H. E.

2016-12-01

The recent National Academy of Sciences Solar and Space Physics Decadal Survey (DS) identified community-consensus science priorities for the decade spanning 2013 - 2022. In this talk, we discuss the ways by which small satellite constellations are already and may soon accelerate progress toward achieving many of these science targets. The DS outlined four overarching science goals: (1) determine the origins of the Sun's activity and predict the variations in the space environment; (2) determine the dynamics and coupling of Earth's magnetosphere, ionosphere, and atmosphere and their response to solar and terrestrial inputs; (3) determine the interaction of the Sun with the solar system and the interstellar medium; and, (4) discover and characterize fundamental processes that occur both within the heliosphere and throughout the universe. These DS science goals provide the context for key science challenges in the three connected parts of the system that encompass all of solar and space physics, herein referred to as geospace: the Sun and heliosphere; the coupled solar wind-magnetosphere system; and, the coupled atmosphere-ionosphere-magnetosphere system. The DS further presented the role that small satellites play in resolving many of these science challenges, with a particular emphasis on the role that constellations of small satellites will play. While once considered by many as being "futuristic" or even "unrealizable", constellations of small satellites are already making important contributions to geospace science and with the promise for more to come. Using the DS as a guidepost, in this presentation, we outline representative small satellite constellation missions alread underway, some in development, and others notionally proposed over the next several years that employ small satellite constellations to tackle large science imperatives. Finally, we give examples of key small satellite technologies in development that will potentially enable great scientific

Construction and material specification

Science.gov (United States)

2002-01-01

These Construction and Material Specifications are written to the Bidder before award of the : Contract and to the Contractor after award of the Contract. The sentences that direct the Contractor to perform Work are written as commands. For example, ...

46 CFR 160.053-3 - Materials, construction and workmanship.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, construction and workmanship. 160.053-3..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Work Vests, Unicellular Plastic Foam § 160.053-3 Materials, construction and workmanship. (a) General. Except as otherwise specifically...

46 CFR 160.038-3 - Materials, workmanship, and construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, workmanship, and construction. 160.038-3..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Magazine Chests, Portable, for Merchant Vessels § 160.038-3 Materials, workmanship, and construction. (a) Portable magazine chests shall...

Management of waste from packaging of construction materials in building construction works

OpenAIRE

González Pericot, Natalia; Río Merino, Mercedes del

2011-01-01

Every material arriving at the construction site comes protected in some type of packaging, fundamentally cardboard, plastic or wood, and presently the great majority of these packagings finish in a container mixed with the rest of waste of the construction work. The increasing tendency to use prefabricated materials increases the volume of packaging necessary in product transport; in addition, the traditional materials also arrive more protected with packaging. A specific management for ...

Environmental impacts of construction materials. A report on the contribution of construction materials to greenhouse gas emissions of construction; Rakennusmateriaalien ympaeristoevaikutukset. Selvitys rakennusmateriaalien vaikutuksesta rakentamisen kasvihuonekaasupaeaestoeihin, tiivistelmaeraportti

Energy Technology Data Exchange (ETDEWEB)

Ruuska, A.; Haekkinen, T.; Vares, S.; Korhonen, M.-R.; Myllymaa, T.

2013-05-15

As the energy performance of new construction improves and the related greenhouse gas (GHG) emissions diminish the carbon footprint of construction materials becomes more important. One objective in the current government's programme is to take into account construction materials and products in the energy performance assessment of buildings. At the request of the Ministry of the Environment, VTT Technical Research Centre of Finland and the Finnish Environment Institute analysed, through a case study, the significance of the environmental impacts of construction materials. The aim was to develop preliminary recommendations for guiding construction. The case study calculated the overall GHG emissions from the materials used in an apartment building over its life cycle and estimated the range of emissions. In addition, the amount of construction waste was assessed, as was the effects of waste management and waste utilisation processes on GHG emissions. This report presents a summary of the results. According to this case study, GHG emissions can vary in typical multi-storey residential buildings within the range of 1 to 2.2 or 1 to 3.9 when the site foundation work also taken into account. The study shows that the construction materials and related processes contribute significantly to the GHG emissions of a building over its life cycle. In fact the level of significance is of the same order as the heating of spaces in an A-class energy performance building. The efficient recycling of materials can contribute to reductions in GHG emissions. The study showed that the estimated benefit was 9 % of the total life-cycle emissions. In the future, specific assessments of different types of waste could look at opportunities for the recycling and reuse of critical materials. Plastics and wood are especially important waste components. Future research topics include improving the use of recycled materials, collecting information on user experiences and enhancing quality

Methodology and Method and Apparatus for Signaling with Capacity Optimized Constellations

Science.gov (United States)

Barsoum, Maged F. (Inventor); Jones, Christopher R. (Inventor)

2017-01-01

Communication systems are described that use geometrically shaped constellations that have increased capacity compared to conventional constellations operating within a similar SNR band. In several embodiments, the geometrically shaped is optimized based upon a capacity measure such as parallel decoding capacity or joint capacity. In many embodiments, a capacity optimized geometrically shaped constellation can be used to replace a conventional constellation as part of a firmware upgrade to transmitters and receivers within a communication system. In a number of embodiments, the geometrically shaped constellation is optimized for an Additive White Gaussian Noise channel or a fading channel.

46 CFR 162.017-3 - Materials, construction, and workmanship.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, construction, and workmanship. 162.017-3..., CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL ENGINEERING EQUIPMENT Valves, Pressure-Vacuum Relief, for Tank Vessels § 162.017-3 Materials, construction, and workmanship. (a) The valves shall be of...

46 CFR 58.05-1 - Material, design and construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Material, design and construction. 58.05-1 Section 58.05... AUXILIARY MACHINERY AND RELATED SYSTEMS Main Propulsion Machinery § 58.05-1 Material, design and construction. (a) The material, design, construction, workmanship, and arrangement of main propulsion machinery...

Constellation labeling optimization for bit-interleaved coded APSK

Science.gov (United States)

Xiang, Xingyu; Mo, Zijian; Wang, Zhonghai; Pham, Khanh; Blasch, Erik; Chen, Genshe

2016-05-01

This paper investigates the constellation and mapping optimization for amplitude phase shift keying (APSK) modulation, which is deployed in Digital Video Broadcasting Satellite - Second Generation (DVB-S2) and Digital Video Broadcasting - Satellite services to Handhelds (DVB-SH) broadcasting standards due to its merits of power and spectral efficiency together with the robustness against nonlinear distortion. The mapping optimization is performed for 32-APSK according to combined cost functions related to Euclidean distance and mutual information. A Binary switching algorithm and its modified version are used to minimize the cost function and the estimated error between the original and received data. The optimized constellation mapping is tested by combining DVB-S2 standard Low-Density Parity-Check (LDPC) codes in both Bit-Interleaved Coded Modulation (BICM) and BICM with iterative decoding (BICM-ID) systems. The simulated results validate the proposed constellation labeling optimization scheme which yields better performance against conventional 32-APSK constellation defined in DVB-S2 standard.

Materials in machine, plant, and apparatus construction

International Nuclear Information System (INIS)

Blumenauer, H.; Hampe, E.; Hoehne, D.

1983-01-01

The subject is covered under the following headings: principles of materials economy and selection, designation of materials, general construction materials; materials for tools, materials for low temperatures, materials for high temperatures, materials for corrosive stress, materials with high wear resistance and friction materials, sliding and bearing materials, materials for spring load, materials for joints, and materials for nuclear reactors

Sustainable material selection for construction industry

DEFF Research Database (Denmark)

Govindan, Kannan; Shankar, Madan; Kannan, Devika

2016-01-01

a hybrid multi criteria decision making (MCDM) methodology with a specific examination of the UAE. The indicators collected from existing literatures were used in evaluation of sustainable construction materials with the assistance of construction sector-based respondents. The proposed framework...

Textile materials for lightweight constructions technologies, methods, materials, properties

CERN Document Server

2016-01-01

In this book, experts on textile technologies convey both general and specific informa­tion on various aspects of textile engineering, ready-made technologies, and textile chemistry. They describe the entire process chain from fiber materials to various yarn constructions, 2D and 3D textile constructions, preforms, and interface layer design. In addition, the authors introduce testing methods, shaping and simulation techniques for the characterization of and structural mechanics calculations on anisotropic, pliable high-performance textiles, including specific examples from the fields of fiber plastic composites, textile concrete, and textile membranes. Readers will also be familiarized with the potential offered by increasingly popular textile structures, for instance in the fields of composite technology, construction technology, security technology, and membrane technology. Textile materials and semi-finished products have widely varied potential characteristics, and are commonly used as essential element...

Cluster analysis of received constellations for optical performance monitoring

NARCIS (Netherlands)

van Weerdenburg, J.J.A.; van Uden, R.; Sillekens, E.; de Waardt, H.; Koonen, A.M.J.; Okonkwo, C.

2016-01-01

Performance monitoring based on centroid clustering to investigate constellation generation offsets. The tool allows flexibility in constellation generation tolerances by forwarding centroids to the demapper. The relation of fibre nonlinearities and singular value decomposition of intra-cluster

48 CFR 25.204 - Evaluating offers of foreign construction material.

Science.gov (United States)

2010-10-01

... foreign construction material. 25.204 Section 25.204 Federal Acquisition Regulations System FEDERAL ACQUISITION REGULATION SOCIOECONOMIC PROGRAMS FOREIGN ACQUISITION Buy American Act-Construction Materials 25.204 Evaluating offers of foreign construction material. (a) Offerors proposing to use foreign...

48 CFR 1325.204 - Evaluating offers of foreign construction material.

Science.gov (United States)

2010-10-01

... foreign construction material. 1325.204 Section 1325.204 Federal Acquisition Regulations System DEPARTMENT OF COMMERCE SOCIOECONOMIC PROGRAMS FOREIGN ACQUISITION Buy American Act-Construction Materials 1325.204 Evaluating offers of foreign construction material. The designee authorized to specify a...

Activity measurements of radon from construction materials

Energy Technology Data Exchange (ETDEWEB)

Fior, L.; Nicolosi Correa, J. [Federal University of Technology - Parana, UTFPR, Av. Sete de Setembro, 3165, Curitiba, PR 80230-901 (Brazil); Paschuk, S.A., E-mail: spaschuk@gmail.com [Federal University of Technology - Parana, UTFPR, Av. Sete de Setembro, 3165, Curitiba, PR 80230-901 (Brazil); Denyak, V.V. [Federal University of Technology - Parana, UTFPR, Av. Sete de Setembro, 3165, Curitiba, PR 80230-901 (Brazil); Schelin, H.R. [Federal University of Technology - Parana, UTFPR, Av. Sete de Setembro, 3165, Curitiba, PR 80230-901 (Brazil); Pele Pequeno Principe Research Institute, Av. Silva Jardim, 1632, Curitiba, PR 80250-200 (Brazil); Soreanu Pecequilo, B.R. [Institute of Nuclear and Energetic Researches, IPEN, Av. Prof. Lineu Prestes, 2242-/05508-000 Sao Paulo (Brazil); Kappke, J. [Federal University of Technology - Parana, UTFPR, Av. Sete de Setembro, 3165, Curitiba, PR 80230-901 (Brazil)

2012-07-15

This work presents the results of radon concentration measurements of construction materials used in the Brazilian industry, such as clay (red) bricks and concrete blocks. The measurements focused on the detection of indoor radon activity during different construction stages and the analysis of radionuclides present in the construction materials. For this purpose, sealed chambers with internal dimensions of approximately 60 Multiplication-Sign 60 Multiplication-Sign 60 cm{sup 3} were built within a protected and isolated laboratory environment, and stable air humidity and temperature levels were maintained. These chambers were also used for radon emanation reduction tests. The chambers were built in four major stages: (1) assembly of the walls using clay (red) bricks, concrete blocks, and mortar; (2) installation of plaster; (3) finishing of wall surface using lime; and (4) insulation of wall surface and finishing using paint. Radon measurements were performed using polycarbonate etched track detectors. By comparing the three layers applied to the masonry walls, it was concluded that only the last step (wall painting using acrylic varnish) reduced the radon emanation, by a factor of approximately 2. Samples of the construction materials (clay bricks and concrete blocks) were ground, homogenized, and subjected to gamma-ray spectrometry analysis to evaluate the activity concentrations of {sup 226}Ra, {sup 232}Th and {sup 40}K. The values for the index of the activity concentration (I), radium equivalent activity (Ra{sub eq}), and external hazard index (H{sub ext}) showed that these construction materials could be used without restrictions or concern about the equivalent dose limit (1 mSv/year). - Highlights: Black-Right-Pointing-Pointer Radon activity in air related to building materials was measured. Black-Right-Pointing-Pointer The index of activity concentration of building materials was evaluated. Black-Right-Pointing-Pointer The radium equivalent activity of

Radiometric and geometric assessment of data from the RapidEye constellation of satellites

Science.gov (United States)

Chander, Gyanesh; Haque, Md. Obaidul; Sampath, Aparajithan; Brunn, A.; Trosset, G.; Hoffmann, D.; Roloff, S.; Thiele, M.; Anderson, C.

2013-01-01

To monitor land surface processes over a wide range of temporal and spatial scales, it is critical to have coordinated observations of the Earth's surface using imagery acquired from multiple spaceborne imaging sensors. The RapidEye (RE) satellite constellation acquires high-resolution satellite images covering the entire globe within a very short period of time by sensors identical in construction and cross-calibrated to each other. To evaluate the RE high-resolution Multi-spectral Imager (MSI) sensor capabilities, a cross-comparison between the RE constellation of sensors was performed first using image statistics based on large common areas observed over pseudo-invariant calibration sites (PICS) by the sensors and, second, by comparing the on-orbit radiometric calibration temporal trending over a large number of calibration sites. For any spectral band, the individual responses measured by the five satellites of the RE constellation were found to differ B2B) alignment of the image data sets. The position accuracy was assessed by comparing the RE imagery against high-resolution aerial imagery, while the B2B characterization was performed by registering each band against every other band to ensure that the proper band alignment is provided for an image product. The B2B results indicate that the internal alignments of these five RE bands are in agreement, with bands typically registered to within 0.25 pixels of each other or better.

Consumer Perceptions of Service Constellations : Implications for Service Innovation

NARCIS (Netherlands)

van Riel, A.C.R.; Calabretta, G.; Driessen, P.H.; Hillebrand, B.; Humphreys, A.; Krafft, M.; Beckers, S.F.M.

2013-01-01

Purpose - The purpose of this paper is to investigate how the service constellation perspective affects innovation strategies and potentially contributes to the innovation literature, proposing a research agenda. Design/methodology/approach - By analyzing the notion of a service constellation, the

48 CFR 625.204 - Evaluating offers of foreign construction material.

Science.gov (United States)

2010-10-01

... foreign construction material. 625.204 Section 625.204 Federal Acquisition Regulations System DEPARTMENT OF STATE SOCIOECONOMIC PROGRAMS FOREIGN ACQUISITION Buy American Act-Construction Materials 625.204 Evaluating offers of foreign construction material. (b) The head of the contracting activity is the agency...

Sibling constellation effects on learning and career aspirations of pupils.

OpenAIRE

KOROTVIČKOVÁ, Blanka

2012-01-01

The thesis "Sibling Constellation Effects on Learning and Career Aspirations of Pupils" is aimed at the description of a relationship between birth order and personality development. It also deals with the general characteristics of sibling constellation and its historical development. It points out the importance of sibling constellation in human life and presents the personality description with regard to birth order in relation to parents, siblings, peers, education and occupation. The the...

Methods and Apparatuses for Signaling with Geometric Constellations in a Raleigh Fading Channel

Science.gov (United States)

Barsoum, Maged F. (Inventor); Jones, Christopher R. (Inventor)

2017-01-01

Communication systems are described that use signal constellations, which have unequally spaced (i.e. `geometrically` shaped) points. In many embodiments, the communication systems use specific geometric constellations that are capacity optimized at a specific SNR, over the Raleigh fading channel. In addition, ranges within which the constellation points of a capacity optimized constellation can be perturbed and are still likely to achieve a given percentage of the optimal capacity increase compared to a constellation that maximizes d.sub.min, are also described. Capacity measures that are used in the selection of the location of constellation points include, but are not limited to, parallel decode (PD) capacity and joint capacity.

Origins of the ancient constellations: I. The Mesopotamian traditions

Science.gov (United States)

Rogers, J. H.

1998-02-01

In the sky-map of ancient Babylon, constellations had two different roles, and thus developed into two overlapping traditions. One set of constellations represented the gods and their symbols; the other set represented rustic activities and provided a farming calendar. Many constellations were shared by the two traditions, but in some regions of sky there were alternative divine and rustic figures. These figures developed in stages from ~3200 BC to ~500 BC. Of the divine set, the most important (although the last to be finalised) were the twelve zodiacal signs, plus several associated animals (the serpent, crow, eagle, and fish), which were all transmitted to the classical Greek sky-map that we still use today. Conversely, the rustic constellations of workers and tools and animals were not transmitted to the West. However, a few of them may have survived in Bedouin Arab sky-maps of the first millennium AD.

Sustainable Management of Construction and Demolition Materials

Science.gov (United States)

This web page discusses how to sustainably manage construction and demolition materials, Information covers, what they are, and how builders, construction crews, demolition teams,and deign practitioners can divert C&D from landfills.

Dark Energy, Dark Matter and Science with Constellation-X

Science.gov (United States)

Cardiff, Ann Hornschemeier

2005-01-01

Constellation-X, with more than 100 times the collecting area of any previous spectroscopic mission operating in the 0.25-40 keV bandpass, will enable highthroughput, high spectral resolution studies of sources ranging from the most luminous accreting supermassive black holes in the Universe to the disks around young stars where planets form. This talk will review the updated Constellation-X science case, released in booklet form during summer 2005. The science areas where Constellation-X will have major impact include the exploration of the space-time geometry of black holes spanning nine orders of magnitude in mass and the nature of the dark energy and dark matter which govern the expansion and ultimate fate of the Universe. Constellation-X will also explore processes referred to as "cosmic feedback" whereby mechanical energy, radiation, and chemical elements from star formation and black holes are returned to interstellar and intergalactic medium, profoundly affecting the development of structure in the Universe, and will also probe all the important life cycles of matter, from stellar and planetary birth to stellar death via supernova to stellar endpoints in the form of accreting binaries and supernova remnants. This talk will touch upon all these areas, with particular emphasis on Constellation-X's role in the study of Dark Energy.

When Construction Material Traders Goes Electronic: Analysis of SMEs in Malaysian Construction Industry

OpenAIRE

Dzul Fahmi Nordin; Rosmini Omar

2012-01-01

This paper analyzed the perception of e-commerce application services by construction material traders in Malaysia. Five attributes were tested: usability, reputation, trust, privacy and familiarity. Study methodology consists of survey questionnaire and statistical analysis that includes reliability analysis, factor analysis, ANOVA and regression analysis. The respondents were construction material traders, including hardware stores in Klang Valley, Kuala Lumpur. Find...

EVALUATION OF CAUSES OF CONSTRUCTION MATERIAL WASTE

African Journals Online (AJOL)

Osondu

factors contributing to construction material waste generation on building sites in Rivers State, ... the studied factors at every level of the construction processes and in their waste management plan. ..... Evaluation of Solid Waste in Building.

Trade-space Analysis for Constellations

Science.gov (United States)

Le Moigne, J.; Dabney, P.; de Weck, O. L.; Foreman, V.; Grogan, P.; Holland, M. P.; Hughes, S. P.; Nag, S.

2016-12-01

Traditionally, space missions have relied on relatively large and monolithic satellites, but in the past few years, under a changing technological and economic environment, including instrument and spacecraft miniaturization, scalable launchers, secondary launches as well as hosted payloads, there is growing interest in implementing future NASA missions as Distributed Spacecraft Missions (DSM). The objective of our project is to provide a framework that facilitates DSM Pre-Phase A investigations and optimizes DSM designs with respect to a-priori Science goals. In this first version of our Trade-space Analysis Tool for Constellations (TAT-C), we are investigating questions such as: "How many spacecraft should be included in the constellation? Which design has the best cost/risk value?" The main goals of TAT-C are to: Handle multiple spacecraft sharing a mission objective, from SmallSats up through flagships, Explore the variables trade space for pre-defined science, cost and risk goals, and pre-defined metrics Optimize cost and performance across multiple instruments and platforms vs. one at a time. This paper describes the overall architecture of TAT-C including: a User Interface (UI) interacting with multiple users - scientists, missions designers or program managers; an Executive Driver gathering requirements from UI, then formulating Trade-space Search Requests for the Trade-space Search Iterator first with inputs from the Knowledge Base, then, in collaboration with the Orbit & Coverage, Reduction & Metrics, and Cost& Risk modules, generating multiple potential architectures and their associated characteristics. TAT-C leverages the use of the Goddard Mission Analysis Tool (GMAT) to compute coverage and ancillary data, streamlining the computations by modeling orbits in a way that balances accuracy and performance. TAT-C current version includes uniform Walker constellations as well as Ad-Hoc constellations, and its cost model represents an aggregate model

Toxic or dangerous substances present construction materials

International Nuclear Information System (INIS)

Campos Alvarado, A.

2003-01-01

The purpose of this investigation is the elaboration of a guide which could be used as a support and consultation concerning the topic of safety in the construction, specifically in the area of the use and managing of material and dangerous substances; considering the possible dangers to medium and long term that some of the common construction materials represent for the health. The gathered information is the result of the review of bibliographical material, the visits to public institutions at national level and to international offices which representation in our country, this way as a work of field and of study of the national market, among others. Besides important consult through the Internet checking many sites of interest with the finality of getting more updated information as possible, like that as the consultation to professionals and workers related to the construction area. (Author) [es

Activity measurements of radon from construction materials.

Science.gov (United States)

Fior, L; Nicolosi Corrêa, J; Paschuk, S A; Denyak, V V; Schelin, H R; Soreanu Pecequilo, B R; Kappke, J

2012-07-01

This work presents the results of radon concentration measurements of construction materials used in the Brazilian industry, such as clay (red) bricks and concrete blocks. The measurements focused on the detection of indoor radon activity during different construction stages and the analysis of radionuclides present in the construction materials. For this purpose, sealed chambers with internal dimensions of approximately 60×60×60 cm3 were built within a protected and isolated laboratory environment, and stable air humidity and temperature levels were maintained. These chambers were also used for radon emanation reduction tests. The chambers were built in four major stages: (1) assembly of the walls using clay (red) bricks, concrete blocks, and mortar; (2) installation of plaster; (3) finishing of wall surface using lime; and (4) insulation of wall surface and finishing using paint. Radon measurements were performed using polycarbonate etched track detectors. By comparing the three layers applied to the masonry walls, it was concluded that only the last step (wall painting using acrylic varnish) reduced the radon emanation, by a factor of approximately 2. Samples of the construction materials (clay bricks and concrete blocks) were ground, homogenized, and subjected to gamma-ray spectrometry analysis to evaluate the activity concentrations of 226Ra, 232Th and 40K. The values for the index of the activity concentration (I), radium equivalent activity (Raeq), and external hazard index (Hext) showed that these construction materials could be used without restrictions or concern about the equivalent dose limit (1 mSv/year). Copyright © 2011 Elsevier Ltd. All rights reserved.

The lost constellations a history of obsolete, extinct, or forgotten star lore

CERN Document Server

Barentine, John C

2016-01-01

Casual stargazers are familiar with many classical figures and asterisms composed of bright stars (e.g., Orion and the Plough), but this book reveals not just the constellations of today but those of yesteryear. The history of the human identification of constellations among the stars is explored through the stories of some influential celestial cartographers whose works determined whether new inventions survived. The history of how the modern set of 88 constellations was defined by the professional astronomy community is recounted, explaining how the constellations described in the book became permanently “extinct.”  Dr. Barentine addresses why some figures were tried and discarded, and also directs observers to how those figures can still be picked out on a clear night if one knows where to look. These lost constellations are described in great detail using historical references, ennabling observers to rediscover them on their own surveys of the sky. Treatment of the obsolete constellations as ...

Sustainable construction : towards a strategic approach to construction material management for waste reduction

NARCIS (Netherlands)

Abarca Guerrero, L.; Scheublin, F.J.M.; Egmond - de Wilde De Ligny, van E.L.C.; Lambert, A.J.D.

2008-01-01

The construction sector plays a key role in shaping and developing the built environment. It also has an undisputed and significant impact on it due to the amounts of materials extracted and produced as waste. The construction industry has emphasized to recycling construction waste (CW), however,

Considering Materials Management in Construction: An Exploratory Study

Directory of Open Access Journals (Sweden)

Zakaria Dakhli

2018-03-01

Full Text Available While materials count for a considerable amount of construction costs, the way materials are managed seems to be improvised rather than approached methodically. This study investigates the practice of novel techniques used to manage materials in the construction industry. Techniques that have already proven themselves to be efficient ways to manage the production pace within the industry include the pull system, Just-In-Time, Kitting and off-site fabrication. These are explained and assessed in the context of the French construction industry through an exploratory study, supported by a questionnaire completed by contractors. The results reveal that a clear plan to manage materials on-site is lacking among the respondents, creating common inventory problems. This research provides evidence to support the central role played by an efficient management of material flow on-site. It also highlights the obstacles that hinder the adoption of innovative techniques, such as sub-contractor coordination.

Mass of materials: the impact of designers on construction ergonomics.

Science.gov (United States)

Smallwood, John

2012-01-01

Many construction injuries are musculoskeletal related in the form of sprains and strains arising from the handling of materials, which are specified by designers. The paper presents the results of a study conducted among delegates attending two 'designing for H&S' (DfH&S) seminars using a questionnaire. The salient findings include: the level of knowledge relative to the mass and density of materials is limited; designers generally do not consider the mass and density of materials when designing structures and elements and specifying materials; to a degree designers appreciate that the mass and density of materials impact on construction ergonomics; designers rate their knowledge of the mass and density of materials as limited, and designers appreciate the potential of the consideration of the mass and density of materials to contribute to an improvement in construction ergonomics. Conclusions include: designers lack the requisite knowledge relative to the mass and density of materials; designers are thus precluded from conducting optimum design hazard identification and risk assessments, and tertiary built environment designer education does not enlighten designers relative to construction ergonomics. Recommendations include: tertiary built environment designer education should construction ergonomics; professional associations should raise the level of awareness relative to construction ergonomics, and design practices should include a category 'mass and density of materials' in their practice libraries.

Natural and construction materials and plant products. Raw materials, constructional physics, design and construction. 2. upd. and enl. ed.; Natuerliche und pflanzliche Baustoffe. Rohstoff - Bauphysik - Konstruktion

Energy Technology Data Exchange (ETDEWEB)

Holzmann, Gerhard; Wangelin, Matthias; Bruns, Rainer

2012-07-01

The book discusses all relevant renewable constructional materials made from fibre or dyeing plants along with their physical and chemical fundamentals. Protection of resources, environmental protection, and pollutants in constructional materials are gone into as well. [German] Dieses Buch behandelt alle wichtige nachwachsenden, pflanzlichen Baustoffe aus Faser- und Faerberpflanzen sowie dazugehoerige physikalische und chemische Grundlagen. Angesprochen werden auch Ressourcen- und Umweltschutz sowie Schadstoffe aus Bauprodukten.

Improved candidate generation and coverage analysis methods for design optimization of symmetric multi-satellite constellations

Science.gov (United States)

Matossian, Mark G.

1997-01-01

Much attention in recent years has focused on commercial telecommunications ventures involving constellations of spacecraft in low and medium Earth orbit. These projects often require investments on the order of billions of dollars (US$) for development and operations, but surprisingly little work has been published on constellation design optimization for coverage analysis, traffic simulation and launch sequencing for constellation build-up strategies. This paper addresses the two most critical aspects of constellation orbital design — efficient constellation candidate generation and coverage analysis. Inefficiencies and flaws in the current standard algorithm for constellation modeling are identified, and a corrected and improved algorithm is presented. In the 1970's, John Walker and G. V. Mozhaev developed innovative strategies for continuous global coverage using symmetric non-geosynchronous constellations. (These are sometimes referred to as rosette, or Walker constellations. An example is pictured above.) In 1980, the late Arthur Ballard extended and generalized the work of Walker into a detailed algorithm for the NAVSTAR/GPS program, which deployed a 24 satellite symmetric constellation. Ballard's important contribution was published in his "Rosette Constellations of Earth Satellites."

Constellation and Mapping Optimization of APSK Modulations used in DVB-S2

Directory of Open Access Journals (Sweden)

L. Jordanova

2014-10-01

Full Text Available This article represents the algorithms of APSK constellation and mapping optimization. The dependencies of the symbol error probability Ps on the parameters of the 16APSK and 32APSK constellations are examined and several options that satisfy the requirements to the minimum value of Ps are selected. Mapping optimization is carried out for the selected APSK constellations. BER characteristics of the satellite DVB-S2 channels are represented when using optimized and standard 16APSK and 32APSK constellations and a comparative analysis of the results achieved is made.

Automating Trend Analysis for Spacecraft Constellations

Science.gov (United States)

Davis, George; Cooter, Miranda; Updike, Clark; Carey, Everett; Mackey, Jennifer; Rykowski, Timothy; Powers, Edward I. (Technical Monitor)

2001-01-01

Spacecraft trend analysis is a vital mission operations function performed by satellite controllers and engineers, who perform detailed analyses of engineering telemetry data to diagnose subsystem faults and to detect trends that may potentially lead to degraded subsystem performance or failure in the future. It is this latter function that is of greatest importance, for careful trending can often predict or detect events that may lead to a spacecraft's entry into safe-hold. Early prediction and detection of such events could result in the avoidance of, or rapid return to service from, spacecraft safing, which not only results in reduced recovery costs but also in a higher overall level of service for the satellite system. Contemporary spacecraft trending activities are manually intensive and are primarily performed diagnostically after a fault occurs, rather than proactively to predict its occurrence. They also tend to rely on information systems and software that are oudated when compared to current technologies. When coupled with the fact that flight operations teams often have limited resources, proactive trending opportunities are limited, and detailed trend analysis is often reserved for critical responses to safe holds or other on-orbit events such as maneuvers. While the contemporary trend analysis approach has sufficed for current single-spacecraft operations, it will be unfeasible for NASA's planned and proposed space science constellations. Missions such as the Dynamics, Reconnection and Configuration Observatory (DRACO), for example, are planning to launch as many as 100 'nanospacecraft' to form a homogenous constellation. A simple extrapolation of resources and manpower based on single-spacecraft operations suggests that trending for such a large spacecraft fleet will be unmanageable, unwieldy, and cost-prohibitive. It is therefore imperative that an approach to automating the spacecraft trend analysis function be studied, developed, and applied to

CubeSat constellation design for air traffic monitoring

Science.gov (United States)

Nag, Sreeja; Rios, Joseph L.; Gerhardt, David; Pham, Camvu

2016-11-01

Suitably equipped global and local air traffic can be tracked. The tracking information may then be used for control from ground-based stations by receiving the Automatic Dependent Surveillance-Broadcast (ADS-B) signal. In this paper, we describe a tool for designing a constellation of small satellites which demonstrates, through high-fidelity modeling based on simulated air traffic data, the value of space-based ADS-B monitoring. It thereby provides recommendations for cost-efficient deployment of a constellation of small satellites to increase safety and situational awareness in the currently poorly-served surveillance area of Alaska. Air traffic data were obtained from NASA's Future ATM Concepts Evaluation Tool, for the Alaskan airspace over one day. The results presented were driven by MATLAB and the satellites propagated and coverage calculated using AGI's Satellite Tool. While Ad-hoc and precession spread constellations have been quantitatively evaluated, Walker constellations show the best performance in simulation. Sixteen satellites in two perpendicular orbital planes are shown to provide more than 99% coverage over representative Alaskan airspace and the maximum time gap where any airplane in Alaska is not covered is six minutes, therefore meeting the standard set by the International Civil Aviation Organization to monitor every airplane at least once every fifteen minutes. In spite of the risk of signal collision when multiple packets arrive at the satellite receiver, the proposed constellation shows 99% cumulative probability of reception within four minutes when the airplanes are transmitting every minute, and at 100% reception probability if transmitting every second. Data downlink can be performed using any of the three ground stations of NASA Earth Network in Alaska.

46 CFR 160.062-3 - Materials, construction, workmanship, and performance requirements.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, construction, workmanship, and performance...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Releases. Lifesaving Equipment, Hydraulic and Manual § 160.062-3 Materials, construction, workmanship, and performance...

46 CFR 160.057-3 - Materials, workmanship, construction, and performance requirements.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, workmanship, construction, and performance...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Floating Orange Smoke Distress Signals (15 Minutes) § 160.057-3 Materials, workmanship, construction, and performance...

46 CFR 160.037-3 - Materials, workmanship, construction, and performance requirements.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, workmanship, construction, and performance...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hand Orange Smoke Distress Signals § 160.037-3 Materials, workmanship, construction, and performance requirements. (a...

46 CFR 160.031-3 - Materials, construction, workmanship, and performance requirements.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, construction, workmanship, and performance...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Line-Throwing Appliance, Shoulder Gun Type (and Equipment) § 160.031-3 Materials, construction, workmanship, and...

46 CFR 160.036-3 - Materials, workmanship, construction and performance requirements.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, workmanship, construction and performance...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hand-Held Rocket-Propelled Parachute Red Flare Distress Signals § 160.036-3 Materials, workmanship, construction and...

46 CFR 160.040-3 - Materials, construction, workmanship, and performance requirements.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, construction, workmanship, and performance...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Line-Throwing Appliance, Impulse-Projected Rocket Type (and Equipment) § 160.040-3 Materials, construction, workmanship...

46 CFR 160.024-3 - Materials, workmanship, construction, and performance requirements.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, workmanship, construction, and performance...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Pistol-Projected Parachute Red Flare Distress Signals § 160.024-3 Materials, workmanship, construction, and performance...

46 CFR 160.058-3 - Materials, workmanship, construction and performance requirements.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, workmanship, construction and performance...) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Desalter Kits, Sea Water, for Merchant Vessels § 160.058-3 Materials, workmanship, construction and performance...

Open Sourcing Social Change: Inside the Constellation Model

OpenAIRE

Tonya Surman; Mark Surman

2008-01-01

The constellation model was developed by and for the Canadian Partnership for Children's Health and the Environment. The model offers an innovative approach to organizing collaborative efforts in the social mission sector and shares various elements of the open source model. It emphasizes self-organizing and concrete action within a network of partner organizations working on a common issue. Constellations are self-organizing action teams that operate within the broader strategic vision of a ...

Highland rural constellations. Territory occupation logics and models of order at the North of Traslasierra [Córdoba, Argentina

Directory of Open Access Journals (Sweden)

Fernando Diaz Terreno

2013-07-01

Full Text Available A set of intentioned readings made on an ancient Córdoba’s landscape reveal the occupation logics developed over centuries of territorial construction. These logics result from the combination of cultural ways of domination and exploitation of space, technical resources available and the natural landscape conditions imposed. From these processes, models of territorial order emerge as operational synthesis from the accumulation of human labor in the territory, gathering –in their own material structure– the key for future planning criteria. Just like constellation structures, order models express a form of spatial organization and some type of rurality specific from Northern Traslasierra. The aim is to arrive at a deep understanding of this postponed territory, show its cultural and natural resources and, through those, build a territorial narrative that places them back on the map of Córdoba’s regions.

Utilization of Construction Waste Composite Powder Materials as Cementitious Materials in Small-Scale Prefabricated Concrete

OpenAIRE

Cuizhen Xue; Aiqin Shen; Yinchuan Guo; Tianqin He

2016-01-01

The construction and demolition wastes have increased rapidly due to the prosperity of infrastructure construction. For the sake of effectively reusing construction wastes, this paper studied the potential use of construction waste composite powder material (CWCPM) as cementitious materials in small-scale prefabricated concretes. Three types of such concretes, namely, C20, C25, and C30, were selected to investigate the influences of CWCPM on their working performances, mechanical properties, ...

Zwitterionic materials for antifouling membrane surface construction.

Science.gov (United States)

He, Mingrui; Gao, Kang; Zhou, Linjie; Jiao, Zhiwei; Wu, Mengyuan; Cao, Jialin; You, Xinda; Cai, Ziyi; Su, Yanlei; Jiang, Zhongyi

2016-08-01

Membrane separation processes are often perplexed by severe and ubiquitous membrane fouling. Zwitterionic materials, keeping electric neutrality with equivalent positive and negative charged groups, are well known for their superior antifouling properties and have been broadly utilized to construct antifouling surfaces for medical devices, biosensors and marine coatings applications. In recent years, zwitterionic materials have been more and more frequently utilized for constructing antifouling membrane surfaces. In this review, the antifouling mechanisms of zwitterionic materials as well as their biomimetic prototypes in cell membranes will be discussed, followed by the survey of common approaches to incorporate zwitterionic materials onto membrane surfaces including surface grafting, surface segregation, biomimetic adhesion, surface coating and so on. The potential applications of these antifouling membranes are also embedded. Finally, we will present a brief perspective on the future development of zwitterionic materials modified antifouling membranes. Membrane fouling is a severe problem hampering the application of membrane separation technology. The properties of membrane surfaces play a critical role in membrane fouling and antifouling behavior/performance. Antifouling membrane surface construction has evolved as a hot research issue for the development of membrane processes. Zwitterionic modification of membrane surfaces has been recognized as an effective strategy to resist membrane fouling. This review summarizes the antifouling mechanisms of zwitterionic materials inspired by cell membranes as well as the popular approaches to incorporate them onto membrane surfaces. It can help form a comprehensive knowledge about the principles and methods of modifying membrane surfaces with zwitterionic materials. Finally, we propose the possible future research directions of zwitterionic materials modified antifouling membranes. Copyright © 2016 Acta Materialia Inc

Information systems for material flow management in construction processes

Science.gov (United States)

Mesároš, P.; Mandičák, T.

2015-01-01

The article describes the options for the management of material flows in the construction process. Management and resource planning is one of the key factors influencing the effectiveness of construction project. It is very difficult to set these flows correctly. The current period offers several options and tools to do this. Information systems and their modules can be used just for the management of materials in the construction process.

Innovative Materials and Techniques in Concrete Construction : ACES Workshop

CERN Document Server

2012-01-01

Recent years have seen enormous advances in the technology of concrete as a material, through which its strength, compactness and ductility can reach levels never dreamed of before. Thanks to these improved material properties, the strength and durability of concrete structures is greatly improved, their weight and dimensions reduced, the scope of concrete as a structural material is widened and – despite the higher material costs – overall economy is possible, with positive impacts on sustainability as well. Similar advances are underway in reinforcing materials, notably high strength steel and fibre-reinforced polymers, and in the way they are combined with concrete into high performance structures. Developments in materials and equipment, as well as new concepts, have lead to innovative construction techniques, reducing cost and construction time and making possible the application of concrete under extreme conditions of construction or environment. All these advances will be highlighted in the book by...

Signal Constellations for Multilevel Coded Modulation with Sparse Graph Codes

NARCIS (Netherlands)

Cronie, H.S.

2005-01-01

A method to combine error-correction coding and spectral efficient modulation for transmission over channels with Gaussian noise is presented. The method of modulation leads to a signal constellation in which the constellation symbols have a nonuniform distribution. This gives a so-called shape gain

48 CFR 252.225-7044 - Balance of Payments Program-Construction Material.

Science.gov (United States)

2010-10-01

... Program-Construction Material. 252.225-7044 Section 252.225-7044 Federal Acquisition Regulations System...—Construction Material. As prescribed in 225.7503(a), use the following clause: Balance of Payments Program—Construction Material (JAN 2009) (a) Definitions. As used in this clause— Commercially available off-the-shelf...

Materials for construction and civil engineering science, processing, and design

CERN Document Server

Margarido, Fernanda

2015-01-01

This expansive volume presents the essential topics related to construction materials composition and their practical application in structures and civil installations. The book's diverse slate of expert authors assemble invaluable case examples and performance data on the most important groups of materials used in construction, highlighting aspects such as nomenclature, the properties, the manufacturing processes, the selection criteria, the products/applications, the life cycle and recyclability, and the normalization. Civil Engineering Materials: Science, Processing, and Design is ideal for practicing architects; civil, construction, and structural engineers, and serves as a comprehensive reference for students of these disciplines. This book also: ·       Provides a substantial and detailed overview of traditional materials used in structures and civil infrastructure ·       Discusses properties of natural and synthetic materials in construction and materials' manufacturing processes ·  �...

Human Systems Integration in Practice: Constellation Lessons Learned

Science.gov (United States)

Zumbado, Jennifer Rochlis

2012-01-01

NASA's Constellation program provided a unique testbed for Human Systems Integration (HSI) as a fundamental element of the Systems Engineering process. Constellation was the first major program to have HSI mandated by NASA's Human Rating document. Proper HSI is critical to the success of any project that relies on humans to function as operators, maintainers, or controllers of a system. HSI improves mission, system and human performance, significantly reduces lifecycle costs, lowers risk and minimizes re-design. Successful HSI begins with sufficient project schedule dedicated to the generation of human systems requirements, but is by no means solely a requirements management process. A top-down systems engineering process that recognizes throughout the organization, human factors as a technical discipline equal to traditional engineering disciplines with authority for the overall system. This partners with a bottoms-up mechanism for human-centered design and technical issue resolution. The Constellation Human Systems Integration Group (HSIG) was a part of the Systems Engineering and Integration (SE&I) organization within the program office, and existed alongside similar groups such as Flight Performance, Environments & Constraints, and Integrated Loads, Structures and Mechanisms. While the HSIG successfully managed, via influence leadership, a down-and-in Community of Practice to facilitate technical integration and issue resolution, it lacked parallel top-down authority to drive integrated design. This presentation will discuss how HSI was applied to Constellation, the lessons learned and best practices it revealed, and recommendations to future NASA program and project managers. This presentation will discuss how Human Systems Integration (HSI) was applied to NASA's Constellation program, the lessons learned and best practices it revealed, and recommendations to future NASA program and project managers on how to accomplish this critical function.

Ice as a Construction Material

Science.gov (United States)

Zuppero, Anthony; Lewis, Joseph

1998-01-01

The use of ice as a construction material is discussed. A model of an ice tire torus space ship, which slowly spins to produce artificial gravity is proposed. The size of the ship, needed to support a given number of people and the required envelope mass is presented.

Control system design for the constellation acquisition phase of the LISA mission

Energy Technology Data Exchange (ETDEWEB)

Cirillo, Francesca; Gath, Peter F, E-mail: francesca.cirillo@astrium.eads.ne, E-mail: peter.gath@astrium.eads.ne [Astrium GmbH Satellites, 88039 Friedrichshafen (Germany)

2009-03-01

The objective of the constellation acquisition phase for the LISA mission is to establish the three laser links between the three spacecraft of the LISA constellation so that the interferometric measurements for the science experiment can commence. The laser beam acquisition for LISA is extremely challenging given the 5 million km distance between the spacecraft, the inherent limits of the attitude sensors accuracy, the orbit determination accuracy issues and the time required to phase-lock the incoming and outgoing laser signals. This paper presents the design of the control system for the acquisition phase of the LISA constellation: the acquisition operational procedure is outlined, guidance laws are defined together with the Gyro Mode attitude control principle, which implements a Kalman filter for disturbances rejection purposes. Constellation-wide non-linear simulations demonstrate that the LISA constellation acquisition phase is feasible by means of the proposed control strategy.

Control system design for the constellation acquisition phase of the LISA mission

International Nuclear Information System (INIS)

Cirillo, Francesca; Gath, Peter F

2009-01-01

The objective of the constellation acquisition phase for the LISA mission is to establish the three laser links between the three spacecraft of the LISA constellation so that the interferometric measurements for the science experiment can commence. The laser beam acquisition for LISA is extremely challenging given the 5 million km distance between the spacecraft, the inherent limits of the attitude sensors accuracy, the orbit determination accuracy issues and the time required to phase-lock the incoming and outgoing laser signals. This paper presents the design of the control system for the acquisition phase of the LISA constellation: the acquisition operational procedure is outlined, guidance laws are defined together with the Gyro Mode attitude control principle, which implements a Kalman filter for disturbances rejection purposes. Constellation-wide non-linear simulations demonstrate that the LISA constellation acquisition phase is feasible by means of the proposed control strategy.

Indigenous Construction Materials for Theater Facilities

Science.gov (United States)

2013-09-01

is shown as a step-by-step plan in Figure 1. ERDC TR-13-13 5 Figure 1. Infrastructure planning. The pyramid can be initially divided into two...disadvantages in terms of constructability, structural integrity, environmental impact, and sociocultural impacts. The lower portions of the pyramid ...United States or the Nile in Sudan and Egypt ) is vital to the local economy and can provide a means for transport- ing such construction materials

Constellation Program Human-System Integration Requirements. Revision E, Nov. 19, 2010

Science.gov (United States)

Dory, Jonathan

2010-01-01

The Human-Systems Integration Requirements (HSIR) in this document drive the design of space vehicles, their systems, and equipment with which humans interface in the Constellation Program (CxP). These requirements ensure that the design of Constellation (Cx) systems is centered on the needs, capabilities, and limitations of the human. The HSIR provides requirements to ensure proper integration of human-to-system interfaces. These requirements apply to all mission phases, including pre-launch, ascent, Earth orbit, trans-lunar flight, lunar orbit, lunar landing, lunar ascent, Earth return, Earth entry, Earth landing, post-landing, and recovery. The Constellation Program must meet NASA's Agency-level human rating requirements, which are intended to ensure crew survival without permanent disability. The HSIR provides a key mechanism for achieving human rating of Constellation systems.

Planning and scheduling algorithms for the COSMO-SkyMed constellation

NARCIS (Netherlands)

Bianchessi, Nicola; Righini, Giovanni

2008-01-01

The COSMO-SkyMed satellite constellation for the observation of the Earth is made of four satellites equipped with radar instruments and is intended for dual use, i.e. for security as well as for environmental monitoring purpose. The planning and scheduling problem for the COSMO-SkyMed constellation

Natural radioactivity in construction materials; Natuerliche Radioaktivitaet in Bauprodukten

Energy Technology Data Exchange (ETDEWEB)

Hoffmann, Bernd [Bundesamt fuer Strahlenschutz, Berlin (Germany)

2017-04-01

Rocks and soils contain traces of uranium and thorium and their daughter products, also the primordial nuclide K-40. Most construction materials are produced from mineral raw materials and residuals from industrial processes, thus natural radionuclides can be detected. The radionuclide concentrations are relevant with respect to radiation protection. Radionuclides in construction materials can cause indoor radiation exposure due to their gamma radiation and due to inhalation of radon a gaseous nuclide that can diffuse out of the materials. Based on new legal developments in the European Union the Bundesamt fuer Strahlenschutz is now again concerned with radiation protection issues of building materials.

Material and construction of primary components

International Nuclear Information System (INIS)

Kaser, A.; Wallner, F.

1978-01-01

The construction of SNR's requires specific properties of the materials, i.e. high strength at temperatures of 600 0 C, adequate creep rupture strength, low long-time embrittlement. Aspects are given for optimalization of the mentioned properties with regard to safe manufacture especially good weldability. The austenitic material X6CrNil811 similar the type AISI 304 SS finally was chosen. Besides the fundamental analysis of the material properties it will be reported about the experiences gained during the manufacturing of the essential components. (author)

49 CFR 178.358-2 - Materials of construction and other requirements.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Materials of construction and other requirements... Materials of construction and other requirements. (a) Phenolic foam insulation must be fire resistant and... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS...

49 CFR 178.356-2 - Materials of construction and other requirements.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Materials of construction and other requirements... Materials of construction and other requirements. (a) Phenolic foam insulation must be fire-resistant and... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS...

Constellations-driven innovation

DEFF Research Database (Denmark)

Hansbøl, Mikala

2011-01-01

The paper presents a science and technology studies and actor-network-theory inspired approach to understanding the development and ongoing re-didactication and re-design of a Danish developed presentation tool called the Theme Board (Tematavlen.dk). It is argued that this approach provides a par...... a particularly useful point of departure for engaging in researching innovation and didactic design of digital teaching and learning instruments such as the Theme Board that are programmed and serviced 'in the sky'. I call this approach: constellation-driven innovations....

Constructing bald eagle nests with natural materials

Science.gov (United States)

T. G. Grubb

1995-01-01

A technique for using natural materials to build artificial nests for bald eagles (Haliaeetus leucocephalus) and other raptors is detailed. Properly constructed nests are as permanently secured to the nest tree or cliff substrate as any eagle-built nest or human-made platform. Construction normally requires about three hours and at least two people. This technique is...

CEOS precipitation constellation

Science.gov (United States)

Neeck, Steven P.; Oki, Riko

2007-10-01

The outcomes of the 19th Committee on Earth Observing Satellites (CEOS) Plenary held in London in November 2005, recognized that the CEOS Implementation Plan for Space-Based Observations for Global Earth Observation System of Systems (GEOSS) should: - identify the supply of space-based observations required to satisfy the requirements expressed by the 10-year implementation plan for GEOSS; and - propose an innovative process whereby the many disparate types of Earth observing programs funded by CEOS Member agencies might contribute to the supply of the required observations. The CEOS Task Force charged with drafting the CEOS Implementation Plan for Space-Based Observations for GEOSS focused its early efforts on the creation of a 'new planning process' which would satisfy the various criteria demanded by member space agencies, and which would hopefully encourage a new phase of specificity and focus in the multi-lateral co-operation efforts undertaken by space agencies under the CEOS umbrella - resulting in improved engagement of all CEOS Members and real implementation results. The CEOS Constellations is the title given to this new process, and four pilot studies have been initiated in order to pioneer and test the concept. The Japan Aerospace Exploration Agency (JAXA) and the National Aeronautics and Space Administration (NASA) were selected as the lead agencies for the study of the development of a CEOS Precipitation Constellation with the support of other CEOS space agency and user community participants. The goals, approach, and anticipated outcomes for the study will be discussed.

Construction demolition wastes, Waelz slag and MSWI bottom ash: a comparative technical analysis as material for road construction.

Science.gov (United States)

Vegas, I; Ibañez, J A; San José, J T; Urzelai, A

2008-01-01

The objective of the study is to analyze the technical suitability of using secondary materials from three waste flows (construction and demolition waste (CDW), Waelz slag and municipal solid waste incineration (MSWI) bottom ash), under the regulations and standards governing the use of materials for road construction. A detailed technical characterization of the materials was carried out according to Spanish General Technical Specifications for Road Construction (PG3). The results show that Waelz slag can be adequate for using in granular structural layers, while CDW fits better as granular material in roadbeds. Likewise, fresh MSWI bottom ash can be used as roadbed material as long as it does not contain a high concentration of soluble salts. This paper also discusses the adequacy of using certain traditional test methods for natural soils when characterizing secondary materials for use as aggregates in road construction.

Additive Construction with Mobile Emplacement (ACME) / Automated Construction of Expeditionary Structures (ACES) Materials Delivery System (MDS)

Science.gov (United States)

Mueller, R. P.; Townsend, I. I.; Tamasy, G. J.; Evers, C. J.; Sibille, L. J.; Edmunson, J. E.; Fiske, M. R.; Fikes, J. C.; Case, M.

2018-01-01

The purpose of the Automated Construction of Expeditionary Structures, Phase 3 (ACES 3) project is to incorporate the Liquid Goods Delivery System (LGDS) into the Dry Goods Delivery System (DGDS) structure to create an integrated and automated Materials Delivery System (MDS) for 3D printing structures with ordinary Portland cement (OPC) concrete. ACES 3 is a prototype for 3-D printing barracks for soldiers in forward bases, here on Earth. The LGDS supports ACES 3 by storing liquid materials, mixing recipe batches of liquid materials, and working with the Dry Goods Feed System (DGFS) previously developed for ACES 2, combining the materials that are eventually extruded out of the print nozzle. Automated Construction of Expeditionary Structures, Phase 3 (ACES 3) is a project led by the US Army Corps of Engineers (USACE) and supported by NASA. The equivalent 3D printing system for construction in space is designated Additive Construction with Mobile Emplacement (ACME) by NASA.

On the optimum signal constellation design for high-speed optical transport networks.

Science.gov (United States)

Liu, Tao; Djordjevic, Ivan B

2012-08-27

In this paper, we first describe an optimum signal constellation design algorithm, which is optimum in MMSE-sense, called MMSE-OSCD, for channel capacity achieving source distribution. Secondly, we introduce a feedback channel capacity inspired optimum signal constellation design (FCC-OSCD) to further improve the performance of MMSE-OSCD, inspired by the fact that feedback channel capacity is higher than that of systems without feedback. The constellations obtained by FCC-OSCD are, however, OSNR dependent. The optimization is jointly performed together with regular quasi-cyclic low-density parity-check (LDPC) code design. Such obtained coded-modulation scheme, in combination with polarization-multiplexing, is suitable as both 400 Gb/s and multi-Tb/s optical transport enabling technology. Using large girth LDPC code, we demonstrate by Monte Carlo simulations that a 32-ary signal constellation, obtained by FCC-OSCD, outperforms previously proposed optimized 32-ary CIPQ signal constellation by 0.8 dB at BER of 10(-7). On the other hand, the LDPC-coded 16-ary FCC-OSCD outperforms 16-QAM by 1.15 dB at the same BER.

Power constellations between Roma pupils and their teachers

Directory of Open Access Journals (Sweden)

Iveta Rožníčková

2017-11-01

Full Text Available The goal of this empirical study is to describe power constellations that are generated in interactions between Roma pupils and their teachers, and also to summarize the basic findings of this research and to point out some real situations that can occur during the teaching lessons. The first part of the thesis describes the differences in the social interaction of Roma pupils. The second part is focused on the authority of the teachers and also on using this authority during the lessons. The third part is focused on pupils‘ strategies that are created based on the requirements of teachers. The basic findings of the research are selected in the methodological section. The research survey revealed five power constellations, which are the subject of this empirical study. The empirical study suggests how teachers and pupils define and shape relationships. From the present paper, a lot of influences are involved in the formation of power constellation, ranging from the personality of the teachers, socializing in school, through family upbringing to cultural differences.

Mathematical Methods of System Analysis in Construction Materials

Science.gov (United States)

Garkina, Irina; Danilov, Alexander

2017-10-01

System attributes of construction materials are defined: complexity of an object, integrity of set of elements, existence of essential, stable relations between elements defining integrative properties of system, existence of structure, etc. On the basis of cognitive modelling (intensive and extensive properties; the operating parameters) materials (as difficult systems) and creation of the cognitive map the hierarchical modular structure of criteria of quality is under construction. It actually is a basis for preparation of the specification on development of material (the required organization and properties). Proceeding from a modern paradigm (model of statement of problems and their decisions) of development of materials, levels and modules are specified in structure of material. It when using the principles of the system analysis allows to considered technological process as the difficult system consisting of elements of the distinguished specification level: from atomic before separate process. Each element of system depending on an effective objective is considered as separate system with more detailed levels of decomposition. Among them, semantic and qualitative analyses of an object (are considered a research objective, decomposition levels, separate elements and communications between them come to light). Further formalization of the available knowledge in the form of mathematical models (structural identification) is carried out; communications between input and output parameters (parametrical identification) are defined. Hierarchical structures of criteria of quality are under construction for each allocated level. On her the relevant hierarchical structures of system (material) are under construction. Regularities of structurization and formation of properties, generally are considered at the levels from micro to a macrostructure. The mathematical model of material is represented as set of the models corresponding to private criteria by which separate

46 CFR 160.013-3 - Materials, workmanship, and construction details.

Science.gov (United States)

2010-10-01

... 46 Shipping 6 2010-10-01 2010-10-01 false Materials, workmanship, and construction details. 160.013-3 Section 160.013-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT... materials, workmanship, and construction details shall be in substantial compliance with the provisions of...

Optimal Maintenance for Stochastically Degrading Staellite Constellations

National Research Council Canada - National Science Library

Cook, Timothy J

2005-01-01

.... Previous work has developed a methodology to compute an optimal replacement policy for a satellite constellation in which satellites were viewed as binary entities, either operational or failed...

46 CFR 50.20-30 - Alternative materials or methods of construction.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Alternative materials or methods of construction. 50.20... ENGINEERING GENERAL PROVISIONS Plan Submittal and Approval § 50.20-30 Alternative materials or methods of construction. (a) When new or alternative procedures, designs, or methods of construction are submitted for...

Construction material processed using lunar simulant in various environments

Science.gov (United States)

Chase, Stan; Ocallaghan-Hay, Bridget; Housman, Ralph; Kindig, Michael; King, John; Montegrande, Kevin; Norris, Raymond; Vanscotter, Ryan; Willenborg, Jonathan; Staubs, Harry

1995-01-01

The manufacture of construction materials from locally available resources in space is an important first step in the establishment of lunar and planetary bases. The objective of the CoMPULSIVE (Construction Material Processed Using Lunar Simulant In Various Environments) experiment is to develop a procedure to produce construction materials by sintering or melting Johnson Space Center Simulant 1 (JSC-1) lunar soil simulant in both earth-based (1-g) and microgravity (approximately 0-g) environments. The characteristics of the resultant materials will be tested to determine its physical and mechanical properties. The physical characteristics include: crystalline, thermal, and electrical properties. The mechanical properties include: compressive tensile, and flexural strengths. The simulant, placed in a sealed graphite crucible, will be heated using a high temperature furnace. The crucible will then be cooled by radiative and forced convective means. The core furnace element consists of space qualified quartz-halogen incandescent lamps with focusing mirrors. Sample temperatures of up to 2200 C are attainable using this heating method.

Aspects of new material application for boilers construction

International Nuclear Information System (INIS)

Czerniawski, R.

1996-01-01

Review of steel types commonly used for energetic boilers construction has been done. The worldwide trends in new materials application for improvement of boilers quality have been discussed. The mechanical properties of boiler construction steels have been shown and compared. 3 refs, 5 figs, 1 tab

Constellation Lessons Learned Executive Summary

Science.gov (United States)

Thomas, L. Dale; Neubek, Deb

2011-01-01

This slide presentation reviews the lessons learned from the Constellation Program (CxP) and identified several factors that contributed to the inability of the CxP to meet the cost and schedule commitments. The review includes a significant section on the context in which the CxP operated since new programs are likely to experience the same constraints.

Materials of construction for silicon crystal growth

Science.gov (United States)

Leipold, M. H.; Odonnell, T. P.; Hagan, M. A.

1980-01-01

The performance of materials for construction and in contact with molten silicon for crystal growth is presented. The basis for selection considers physical compatibility, such as thermal expansion and strength, as well as chemical compatibility as indicated by contamination of the silicon. A number of new high technology materials are included as well as data on those previously used. Emphasis is placed on the sources and processing of such materials in that results are frequently dependent on the way a material is prepared as well as its intrinsic constituents.

Exploring the Architectural Tradespace of Severe Weather Monitoring Nanosatellite Constellations

Science.gov (United States)

Hitomi, N.; Selva, D.; Blackwell, W. J.

2014-12-01

MicroMAS-1, a 3U nanosatellite developed by MIT/LL, MIT/SSL, and University of Massachusetts, was launched on July 13, 2014 and is scheduled for deployment from the International Space Station in September. The development of MicroMAS motivates an architectural analysis of a constellation of nanosatellites with the goal of drastically reducing the cost of observing severe storms compared with current monolithic missions such as the Precision and All-Weather Temperature and Humidity (PATH) mission from the NASA Decadal Survey. Our goal is to evolve the instrument capability on weather monitoring nanosatellites to achieve higher performance and better satisfy stakeholder needs. Clear definitions of performance requirements are critical in the conceptual design phase when much of the project's lifecycle cost and performance will be fixed. Ability to perform trade studies and optimization of performance needs with instrument capability will enable design teams to focus on key technologies that will introduce high value and high return on investment. In this work, we approach the significant trades and trends of constellations for monitoring severe storms by applying our rule-based decision support tool. We examine a subset of stakeholder groups listed in the OSCAR online database (e.g., weather, climate) that would benefit from severe storm weather data and their respective observation requirements (e.g. spatial resolution, accuracy). We use ten parameters in our analysis, including atmospheric temperature, humidity, and precipitation. We compare the performance and cost of thousands of different possible constellations. The constellations support hyperspectral sounders that cover different portions of the millimeter-wave spectrum (50-60 GHz, 118GHz, 183GHz) in different orbits, and the performance results are compared against those of the monolithic PATH mission. Our preliminary results indicate that constellations using the hyperspectral millimeter wave sounders can

Typology of person-environment fit constellations: a platform addressing accessibility problems in the built environment for people with functional limitations.

Science.gov (United States)

Slaug, Björn; Schilling, Oliver; Iwarsson, Susanne; Carlsson, Gunilla

2015-09-02

Making the built environment accessible for all regardless of functional capacity is an important goal for public health efforts. Considerable impediments to achieving this goal suggest the need for valid measurements of acccessibility and for greater attention to the complexity of person-environment fit issues. To address these needs, this study aimed to provide a methodological platform, useful for further research and instrument development within accessibility research. This was accomplished by the construction of a typology of problematic person-environment fit constellations, utilizing an existing methodology developed to assess and analyze accessibility problems in the built environment. By means of qualitative review and statistical methods we classified the person-environment fit components covered by an existing application which targets housing accessibility: the Housing Enabler (HE) instrument. The International Classification of Functioning, Disability and Health (ICF) was used as a conceptual framework. Qualitative classification principles were based on conceptual similarities and for quantitative analysis of similarities, Principal Component Analysis was carried out. We present a typology of problematic person-environment fit constellations classified along three dimensions: 1) accessibility problem range and severity 2) aspects of functioning 3) environmental context. As a result of the classification of the HE components, 48 typical person-environment fit constellations were recognised. The main contribution of this study is the proposed typology of person-environment fit constellations. The typology provides a methodological platform for the identification and quantification of problematic person-environment fit constellations. Its link to the globally accepted ICF classification system facilitates communication within the scientific and health care practice communities. The typology also highlights how relations between aspects of functioning

Regional positioning using a low Earth orbit satellite constellation

Science.gov (United States)

Shtark, Tomer; Gurfil, Pini

2018-02-01

Global and regional satellite navigation systems are constellations orbiting the Earth and transmitting radio signals for determining position and velocity of users around the globe. The state-of-the-art navigation satellite systems are located in medium Earth orbits and geosynchronous Earth orbits and are characterized by high launching, building and maintenance costs. For applications that require only regional coverage, the continuous and global coverage that existing systems provide may be unnecessary. Thus, a nano-satellites-based regional navigation satellite system in Low Earth Orbit (LEO), with significantly reduced launching, building and maintenance costs, can be considered. Thus, this paper is aimed at developing a LEO constellation optimization and design method, using genetic algorithms and gradient-based optimization. The preliminary results of this study include 268 LEO constellations, aimed at regional navigation in an approximately 1000 km × 1000 km area centered at the geographic coordinates [30, 30] degrees. The constellations performance is examined using simulations, and the figures of merit include total coverage time, revisit time, and geometric dilution of precision (GDOP) percentiles. The GDOP is a quantity that determines the positioning solution accuracy and solely depends on the spatial geometry of the satellites. Whereas the optimization method takes into account only the Earth's second zonal harmonic coefficient, the simulations include the Earth's gravitational field with zonal and tesseral harmonics up to degree 10 and order 10, Solar radiation pressure, drag, and the lunisolar gravitational perturbation.

The research on the material management system in nuclear power plant construction process

International Nuclear Information System (INIS)

Liu Xuegeng; Huang Zhongping

2010-01-01

According to the module construction speciality of nuclear power plant, this article analyzes the relationship between the actual amount of the material transported to the construction site and the planed needs of the material, and points out the zero inventory management target in the nuclear power plant construction site. Based on this, the article put forward a nuclear power plant material management system which is based on the 'pull' information driver. This system is composed by material coding sub-system, procurement and site material integrated management sub-system and project control sub-system, and is driven by the material demand from construction site to realize the JIT purchasing. This structure of the system can reduce the gap between the actual amount of the material transported to the site and the planed needs of the material and achieve the target of reducing storage at construction site. (authors)

Impact of eccentricity build-up and graveyard disposal Strategies on MEO navigation constellations

Science.gov (United States)

Radtke, Jonas; Domínguez-González, Raúl; Flegel, Sven K.; Sánchez-Ortiz, Noelia; Merz, Klaus

2015-12-01

With currently two constellations being in or close to the build-up phase, in a few years the Medium Earth Orbit (MEO) region will be populated with four complete navigation systems in relatively close orbital altitudes: The American GPS, Russian GLONASS, European Galileo, and Chinese BeiDou. To guarantee an appropriate visibility of constellation satellites from Earth, these constellations rely on certain defined orbits. For this, both the repeat pattern, which is basically defined by the semimajor axis and inclination, as well as the orbital planes, which are defined by the right ascension of ascending node, are determining values. To avoid an overcrowding of the region of interest, the disposal of satellites after their end-of-life is recommended. However, for the MEO region, no internationally agreed mitigation guidelines exist. Because of their distances to Earth, ordinary disposal manoeuvres leading to a direct or delayed re-entry due to atmospheric drag are not feasible: The needed fuel masses for such manoeuvres are by far above the reasonable limits and available fuel budgets. Thus, additional approaches have to be applied. For this, in general two options exist: disposal to graveyard orbits or the disposal to eccentricity build-up orbits. In the study performed, the key criterion for the graveyard strategy is that the disposed spacecraft must keep a safe minimum distance to the altitude of the active constellation on a long-term time scale of up to 200 years. This constraint imposes stringent requirements on the stability of the graveyard orbit. Similar disposals are also performed for high LEO satellites and disposed GEO payloads. The eccentricity build-up strategy on the other hand uses resonant effects between the Earth's geopotential, the Sun and the Moon. Depending on the initial conditions, these can cause a large eccentricity build-up, which finally can lead to a re-entry of the satellite. In this paper, the effects of applying either the first or

Optimising material procurement for construction waste minimization: An exploration of success factors

OpenAIRE

Ajayi, SO; Oyedele, LO; Akinade, OO; Bilal, M; Alaka, HA; Owolabi, HA

2017-01-01

Although construction waste occurs during the actual construction activities, there is an understanding that it is caused by activities and actions at design, materials procurement and construction stages of project delivery processes. This study investigates the material procurement and logistics measures for mitigating waste generated by construction activities. In a bid to explore the phenomenon from the perspectives of experts from the construction industry, this study used a combination ...

Intelligent Materials Tracking System for Construction Projects Management

Directory of Open Access Journals (Sweden)

Narimah Kasim

2015-05-01

Full Text Available An essential factor adversely affecting the performance of construction projects is the improper handling of materials during site activities. In addition, paper-based reports are mostly used to record and exchange information related to the material components within the supply chain, which is problematic and inefficient. Generally, technologies (such as wireless systems and RFID are not being adequately used to overcome human errors and are not well integrated with project management systems to make tracking and management of materials easier and faster. Findings from a literature review and surveys showed that there is a lack of positive examples of such tools having been used effectively. Therefore, this research focused on the development of a materials tracking system that integrates RFID-based materials management with resources modelling to improve on-site materials tracking. Rapid prototyping was used to develop the system and testing of the system was carried out to examine the functionality and working appropriately. The proposed system is intended to promote the employment of RFID for automatic materials tracking with integration of resource modelling (Microsoft (R Office Project in the project management system in order to establish which of the tagged components are required resources for certain project tasks. In conclusion, the system provides an automatic and easy tracking method for managing materials during materials delivery and inventory management processes in construction projects.

Needs study of polymer materials concrete constructions; Behovsstudie av polymera material i betongkonstruktioner

Energy Technology Data Exchange (ETDEWEB)

Blomfeldt, Thomas; Bergsjoe, Petter

2013-02-15

Polymeric materials are frequently used in concrete constructions at hydro and nuclear power facilities. They are most commonly used as expansion joints, seals, lead-thought's, coatings and as additives in cement or mortar. Polymeric materials in concrete constructions are difficult to evaluate, since they are often located within the concrete construction. In some cases the materials have been in place for over 30 years. In addition, these materials are also used to a great extent e.g. as protective coating on all concrete in a nuclear power plant or as several kilometres of joints. Replacing these materials is difficult, time consuming and very costly. That is why it is of great importance to evaluate their actual status and life-time expectancy with the largest possible precision. This report summarises the research needs in nuclear and hydro power regarding polymers in concrete constructions. During the project information has been gathered through inspections, interviews and surveys, to obtain the clearest possible picture of which polymeric components that have a need of in-depth research. In this project the nuclear power plants Oskarshamn (O1, O2 and O3), Forsmark (F2) and Ringhals (R1, R2 and R3) were visited. In the field of hydro power the concrete laboratory of Vattenfall R and D in Aalvkarleby and the hydro power plants of Aalvkarleby and Olidan were visited. The studies indicate that there are different needs for hydro and nuclear power. The survey showed that hydro-power facilities have a greater interest in joints. The nuclear power plants are more interested in components that are related to either the plant's security or if the component could lead to high future maintenance costs.

46 CFR 160.023-3 - Materials, workmanship, construction, and performance requirements.

Science.gov (United States)

2010-10-01

... requirements. 160.023-3 Section 160.023-3 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) EQUIPMENT, CONSTRUCTION, AND MATERIALS: SPECIFICATIONS AND APPROVAL LIFESAVING EQUIPMENT Hand Combination... requirements. (a) The materials, construction, workmanship, general and detail requirements shall conform to...

Molecular tools for the construction of peptide-based materials.

Science.gov (United States)

Ramakers, B E I; van Hest, J C M; Löwik, D W P M

2014-04-21

Proteins and peptides are fundamental components of living systems where they play crucial roles at both functional and structural level. The versatile biological properties of these molecules make them interesting building blocks for the construction of bio-active and biocompatible materials. A variety of molecular tools can be used to fashion the peptides necessary for the assembly of these materials. In this tutorial review we shall describe five of the main techniques, namely solid phase peptide synthesis, native chemical ligation, Staudinger ligation, NCA polymerisation, and genetic engineering, that have been used to great effect for the construction of a host of peptide-based materials.

48 CFR 52.225-10 - Notice of Buy American Act Requirement-Construction Materials.

Science.gov (United States)

2010-10-01

... Requirement-Construction Materials. 52.225-10 Section 52.225-10 Federal Acquisition Regulations System FEDERAL... Provisions and Clauses 52.225-10 Notice of Buy American Act Requirement—Construction Materials. As prescribed... Materials (FEB 2009) (a) Definitions. “Commercially available off-the-shelf (COTS) item,” “construction...

The possibility of using materials based on secondary gravel in civil construction

Directory of Open Access Journals (Sweden)

Galitskova Yulia

2017-01-01

Full Text Available By now, the wear and tear of housing stock is more than 50%. Each year the number of old and dilapidated housing is growing, but it is gradually replaced by modern buildings. However, wastes accumulated from dismantling of buildings and constructions, are underutilized and, usually are just stored at landfills, or used for temporary roads construction. The purpose of this research is to define construction wastes characteristics and to explore possibilities for recycling of wastes from construction materials production. The paper also analyzes housing stock condition and basic requirements to building materials used in construction; and demonstrates results building materials based on secondary gravel investigation. While working with materials based on waste requirements the authors conducted laboratory research. Thus, the paper presents the analysis of laboratory tests results that made it possible to draw conclusions about the possible use of building materials based on secondary gravel and about their conformity to specified requirements. The researchers also developed proposals and recommendations to improve the competitiveness of such materials.

Light Water Reactor Sustainability Constellation Pilot Project FY11 Summary Report

International Nuclear Information System (INIS)

Johansen, R.

2011-01-01

Summary report for Fiscal Year 2011 activities associated with the Constellation Pilot Project. The project is a joint effor between Constellation Nuclear Energy Group (CENG), EPRI, and the DOE Light Water Reactor Sustainability Program. The project utilizes two CENG reactor stations: R.E. Ginna and Nine Point Unit 1. Included in the report are activities associate with reactor internals and concrete containments.

Towards high-performance materials for road construction

Science.gov (United States)

Gladkikh, V.; Korolev, E.; Smirnov, V.

2017-10-01

Due to constant increase of traffic, modern road construction is in need of high-performance pavement materials. The operational performance of such materials can be characterized by many properties. Nevertheless, the most important ones are resistance to rutting and resistance to dynamical loads. It was proposed earlier to use sulfur extended asphalt concrete in road construction practice. To reduce the emission of sulfur dioxide and hydrogen sulfide during the concrete mix preparation and pavement production stages, it is beneficial to make such a concrete on the base of complex sulfur modifier. In the present work the influence of the complex modifier to mechanical properties of sulfur extended asphalt concrete was examined. It was shown that sulfur extended asphalt concrete is of high mechanical properties. It was also revealed that there as an anomalous negative correlations between strain capacity, fatigue life and fracture toughness.

Recent trend in construction materials field. Kenzai bun[prime]ya ni okeru saikin no doko

Energy Technology Data Exchange (ETDEWEB)

Tominaga, M [Kawasaki Steel Corp., Tokyo (Japan)

1992-09-01

The Japanese construction industry, the construction market and the technical trend of construction materials made by Kawasaki Steel Group were described. The roles of the steel industry in the construction material market are to increase the ratio of steel used in construction, to manufacture steel products of high value added and to develop new applications. Appearance and good design are required to provide for the construction materials made of processed steel in addition to the necessary functions. In the construction material market, qualitative changes in needs are taking place, such as labor saving shortening of construction period and simplification of construction management. Kawasaki Steel Group intends to expand the integrated business such as system building, external wall materials for buildings made of metals, highly corrosion resistant stainless steel for metallic roof field, and roof materials of the heat insulation, good appearance and horizontally covering type based on the overall business strategy. In addition, Kawasaki Steel Group is expanding the Kawasaki Design Steel Plaza and its construction material research laboratory to cope with the trend of diversified functions and design of construction goods and of making kinds of construction material much more and to develop more rational construction techniques. 1 ref., 8 figs.

Waste glass as eco-friendly replacement material in construction products

Science.gov (United States)

Sharma, Gayatri; Sharma, Anu

2018-05-01

Atpresent time the biggest issue is increasing urban population, industrialization and development all over the world. The quantity of the raw materials of construction products like cement, concrete etc is gradually depleting. This is important because if we don't find the alternative material to accomplish need of this industry, with every year it will put pressure on natural resources which are limited in quantity. This major issue can be solved by partial replacing with waste glass of different construction products. This paper gives an overview of the current growth and recycling situation of waste glass and point out the direction for the proper use of waste glass as replacement of construction material. These will not only help in the reuse of waste glass but also create eco-friendly environment.

Enablers of Innovation in the Construction Material Industry

DEFF Research Database (Denmark)

Wandahl, Søren; Lassen, Astrid Heidemann; Jacobsen, Alexia

2014-01-01

, which creates a strong interdependence between the different supply network partners and can be seen as a hindrance for innovation. Innovation models must embrace such a contemporary business structures, where competition often takes place between supply chains rather than between individual companies......The construction material industry is often acknowledged as slightly more innovative than the overall construction industry and could hence serve as a valuable learning place for how innovation could flourish in the construction industry. Construction is viewed as network or supply chain based......, it was found that different approaches for facilitating this journey exists, based on company characteristics. This paper adds to the body of knowledge on how to succeed with innovation in the construction industry. The increased awareness of an open and cooperative approach to innovation is of value both...

Comparative evaluation of low cost materials as constructed wetland filling media

Science.gov (United States)

Pinho, Henrique J. O.; Vaz, Mafalda M.; Mateus, Dina M. R.

2017-11-01

Three waste materials from civil construction activities were assessed as low cost alternative filling materials used in Constructed Wetlands (CW). CW are green processes for wastewater treatment, whose design includes an appropriate selection of vegetation and filling material. The sustainability of such processes may be incremented using recovered wastes as filling materials. The abilities of the materials to support plant growth and to contribute to pollutants removal from wastewater were assessed and compared to expanded clay, a filling usually used in CW design. Statistical analysis, using one-way ANOVA and Welch's ANOVA, demonstrate that limestone fragments are a better choice of filling material than brick fragments and basalt gravel.

Earth Radiation Imbalance from a Constellation of 66 Iridium Satellites: Technological Aspects

Science.gov (United States)

Wiscombe, W.; Chiu, C. J-Y.

2012-01-01

Iridium Communications Inc. is launching a new generation of polar orbiting communication satellites in 2015-2017. Iridium will provide a hosted payload bay on each of the 66 satellites (plus 6 in-space spares). This offers the potential for a paradigm shift in the way we measure Earth radiation imbalance from space, as well as massive cost savings. Because the constellation provides 24/7 global coverage, there is no need to account for diurnal cycle via extrapolations from uncalibrated narrowband geostationary imagers. And the spares can be rolled over to view the Sun and deep space, then transfer their calibration to the other members of the constellation during the frequent cross-overs. In part using simulations of the constellation viewing realistic Earth scenes, this presentation will address the technological aspects of such a constellation: (1) the calibration strategy; (2) the highly-accurate and stable radiometers for measuring outgoing flux; and (3) the GRACE-inspired algorithms for representing the outgoing flux field in spherical harmonics and thus achieving rv500-km spatial resolution and two-hour temporal resolution.

Estimating construction and demolition debris generation using a materials flow analysis approach.

Science.gov (United States)

Cochran, K M; Townsend, T G

2010-11-01

The magnitude and composition of a region's construction and demolition (C&D) debris should be understood when developing rules, policies and strategies for managing this segment of the solid waste stream. In the US, several national estimates have been conducted using a weight-per-construction-area approximation; national estimates using alternative procedures such as those used for other segments of the solid waste stream have not been reported for C&D debris. This paper presents an evaluation of a materials flow analysis (MFA) approach for estimating C&D debris generation and composition for a large region (the US). The consumption of construction materials in the US and typical waste factors used for construction materials purchasing were used to estimate the mass of solid waste generated as a result of construction activities. Debris from demolition activities was predicted from various historical construction materials consumption data and estimates of average service lives of the materials. The MFA approach estimated that approximately 610-78 × 10(6)Mg of C&D debris was generated in 2002. This predicted mass exceeds previous estimates using other C&D debris predictive methodologies and reflects the large waste stream that exists. Copyright © 2010 Elsevier Ltd. All rights reserved.

SmallSat Constellation Inter-satellite Link System Simulator

Data.gov (United States)

National Aeronautics and Space Administration — Goddard Space Flight Center Distributed Space Mission (DSM) seeks to design and develop the technologies required to achieve the mission goals.  For a constellation...

International Earth Science Constellation (ESC) Introduction

Science.gov (United States)

Guit, William J.; Machado, Michael J.

2016-01-01

This is the Welcome and Introduction presentation for the International Earth Science Constellation (ESC) Mission Operations Working Group (MOWG) meeting held in Albuquerque NM from September 27-29. It contains an org chart, charter, history, significant topics to be discussed, AquaAura 2017 inclination adjust maneuver calendar, a-train long range plans, upcoming events, and action items.

Fire-resistant materials for aircraft passenger seat construction

Science.gov (United States)

Fewell, L. L.; Tesoro, G. C.; Moussa, A.; Kourtides, D. A.

1979-01-01

The thermal response characteristics of fabric and fabric-foam assemblies are described. The various aspects of the ignition behavior of contemporary aircraft passenger seat upholstery fabric materials relative to fabric materials made from thermally stable polymers are evaluated. The role of the polymeric foam backing on the thermal response of the fabric-foam assembly is also ascertained. The optimum utilization of improved fire-resistant fabric and foam materials in the construction of aircraft passenger seats is suggested.

The construction of irradiated material examination facility

International Nuclear Information System (INIS)

Ro, Seung Gy; Lee, Key Soon; Herr, Young Hoi

1990-03-01

A detail design of the examination process, the hot cell facility and the annexed facility of the irradiated material examination facility (IMEF) which will be utilized to examine and evaluate physical and mechanical properties of neutron-irradiated materials, has been performed. Also a start-up work of the underground structure construction has been launched out. The project management and tasks required for the license application were duly carried out. The resultant detail design data will be used for the next step. (author)

Distribution of materials in construction and demolition waste in Portugal.

Science.gov (United States)

Coelho, André; de Brito, Jorge

2011-08-01

It may not be enough simply to know the global volume of construction and demolition waste (CDW) generated in a certain region or country if one wants to estimate, for instance, the revenue accruing from separating several types of materials from the input entering a given CDW recycling plant. A more detailed determination of the distribution of the materials within the generated CDW is needed and the present paper addresses this issue, distinguishing different buildings and types of operation (new construction, retrofitting and demolition). This has been achieved by measuring the materials from buildings of different ages within the Portuguese building stock, and by using direct data from demolition/retrofitting sites and new construction average values reported in the literature. An attempt to establish a benchmark with other countries is also presented. This knowledge may also benefit industry management, especially that related to CDW recycling, helping to optimize procedures, equipment size and operation and even industrial plant spatial distribution. In an extremely competitive market, where as in Portugal low-tech and high environmental impact procedures remain the norm in the construction industry (in particular, the construction waste industry), the introduction of a successful recycling industry is only possible with highly optimized processes and based on a knowledge-based approach to problems.

Precise orbit determination of Multi-GNSS constellation including GPS GLONASS BDS and GALIEO

Science.gov (United States)

Dai, Xiaolei

2014-05-01

In addition to the existing American global positioning system (GPS) and the Russian global navigation satellite system (GLONASS), the new generation of GNSS is emerging and developing, such as the Chinese BeiDou satellite navigation system (BDS) and the European GALILEO system. Multi-constellation is expected to contribute to more accurate and reliable positioning and navigation service. However, the application of multi-constellation challenges the traditional precise orbit determination (POD) strategy that was designed usually for single constellation. In this contribution, we exploit a more rigorous multi-constellation POD strategy for the ongoing IGS multi-GNSS experiment (MGEX) where the common parameters are identical for each system, and the frequency- and system-specified parameters are employed to account for the inter-frequency and inter-system biases. Since the authorized BDS attitude model is not yet released, different BDS attitude model are implemented and their impact on orbit accuracy are studied. The proposed POD strategy was implemented in the PANDA (Position and Navigation Data Analyst) software and can process observations from GPS, GLONASS, BDS and GALILEO together. The strategy is evaluated with the multi-constellation observations from about 90 MGEX stations and BDS observations from the BeiDou experimental tracking network (BETN) of Wuhan University (WHU). Of all the MGEX stations, 28 stations record BDS observation, and about 80 stations record GALILEO observations. All these data were processed together in our software, resulting in the multi-constellation POD solutions. We assessed the orbit accuracy for GPS and GLONASS by comparing our solutions with the IGS final orbit, and for BDS and GALILEO by overlapping our daily orbit solution. The stability of inter-frequency bias of GLONASS and inter-system biases w.r.t. GPS for GLONASS, BDS and GALILEO were investigated. At last, we carried out precise point positioning (PPP) using the multi-constellation

Investigations of construction materials by means of cracking mechanics

International Nuclear Information System (INIS)

Bilous, W.; Wasiak, J.

1995-01-01

The diagnostic procedure for typical construction materials based on cracking tests has been presented. Results of investigations for aluminium base alloys and tungsten sintered materials have been shown and discussed. Application of the method for pipelines testing has been also performed. 6 figs, 2 tabs

Trade-Space Analysis Tool for Constellations (TAT-C)

Science.gov (United States)

Le Moigne, Jacqueline; Dabney, Philip; de Weck, Olivier; Foreman, Veronica; Grogan, Paul; Holland, Matthew; Hughes, Steven; Nag, Sreeja

2016-01-01

Traditionally, space missions have relied on relatively large and monolithic satellites, but in the past few years, under a changing technological and economic environment, including instrument and spacecraft miniaturization, scalable launchers, secondary launches as well as hosted payloads, there is growing interest in implementing future NASA missions as Distributed Spacecraft Missions (DSM). The objective of our project is to provide a framework that facilitates DSM Pre-Phase A investigations and optimizes DSM designs with respect to a-priori Science goals. In this first version of our Trade-space Analysis Tool for Constellations (TAT-C), we are investigating questions such as: How many spacecraft should be included in the constellation? Which design has the best costrisk value? The main goals of TAT-C are to: Handle multiple spacecraft sharing a mission objective, from SmallSats up through flagships, Explore the variables trade space for pre-defined science, cost and risk goals, and pre-defined metrics Optimize cost and performance across multiple instruments and platforms vs. one at a time.This paper describes the overall architecture of TAT-C including: a User Interface (UI) interacting with multiple users - scientists, missions designers or program managers; an Executive Driver gathering requirements from UI, then formulating Trade-space Search Requests for the Trade-space Search Iterator first with inputs from the Knowledge Base, then, in collaboration with the Orbit Coverage, Reduction Metrics, and Cost Risk modules, generating multiple potential architectures and their associated characteristics. TAT-C leverages the use of the Goddard Mission Analysis Tool (GMAT) to compute coverage and ancillary data, streamlining the computations by modeling orbits in a way that balances accuracy and performance.TAT-C current version includes uniform Walker constellations as well as Ad-Hoc constellations, and its cost model represents an aggregate model consisting of

Constellation Program: Lessons Learned. Volume 1; Executive Summary

Science.gov (United States)

Rhatigan, Jennifer L. (Editor)

2011-01-01

This document (Volume I) provides an executive summary of the lessons learned from the Constellation Program. A companion Volume II provides more detailed analyses for those seeking further insight and information. In this volume, Section 1.0 introduces the approach in preparing and organizing the content to enable rapid assimilation of the lessons. Section 2.0 describes the contextual framework in which the Constellation Program was formulated and functioned that is necessary to understand most of the lessons. Context of a former program may seem irrelevant in the heady days of new program formulation. However, readers should take some time to understand the context. Many of the lessons would be different in a different context, so the reader should reflect on the similarities and differences in his or her current circumstances. Section 3.0 summarizes key findings developed from the significant lessons learned at the program level that appear in Section 4.0. Readers can use the key findings in Section 3.0 to peruse for particular topics, and will find more supporting detail and analyses in Section 4.0 in a topical format. Appendix A contains a white paper describing the Constellation Program formulation that may be of use to readers wanting more context or background information. The reader will no doubt recognize some very similar themes from previous lessons learned, blue-ribbon committee reviews, National Academy reviews, and advisory panel reviews for this and other large-scale human spaceflight programs; including Apollo, Space Shuttle, Shuttle/Mir, and the ISS. This could represent an inability to learn lessons from previous generations; however, it is more likely that similar challenges persist in the Agency structure and approach to program formulation, budget advocacy, and management. Perhaps the greatest value of these Constellation lessons learned can be found in viewing them in context with these previous efforts to guide and advise the Agency and its

RECOMMENDED FOUNDATION FILL MATERIALS CONSTRUCTION STANDARD OF THE FLORIDA RADON RESEARCH PROGRAM

Science.gov (United States)

The report summarizes the technical basis for a recommended foundation fill materials standard for new construction houses in Florida. he radon-control construction standard was developed by the Florida Radon Research Program (FRRP). ill material standards are formulated for: (1)...

Materials and techniques for model construction

Science.gov (United States)

Wigley, D. A.

1985-01-01

The problems confronting the designer of models for cryogenic wind tunnel models are discussed with particular reference to the difficulties in obtaining appropriate data on the mechanical and physical properties of candidate materials and their fabrication technologies. The relationship between strength and toughness of alloys is discussed in the context of maximizing both and avoiding the problem of dimensional and microstructural instability. All major classes of materials used in model construction are considered in some detail and in the Appendix selected numerical data is given for the most relevant materials. The stepped-specimen program to investigate stress-induced dimensional changes in alloys is discussed in detail together with interpretation of the initial results. The methods used to bond model components are considered with particular reference to the selection of filler alloys and temperature cycles to avoid microstructural degradation and loss of mechanical properties.

Optimal signal constellation design for ultra-high-speed optical transport in the presence of nonlinear phase noise.

Science.gov (United States)

Liu, Tao; Djordjevic, Ivan B

2014-12-29

In this paper, we first describe an optimal signal constellation design algorithm suitable for the coherent optical channels dominated by the linear phase noise. Then, we modify this algorithm to be suitable for the nonlinear phase noise dominated channels. In optimization procedure, the proposed algorithm uses the cumulative log-likelihood function instead of the Euclidian distance. Further, an LDPC coded modulation scheme is proposed to be used in combination with signal constellations obtained by proposed algorithm. Monte Carlo simulations indicate that the LDPC-coded modulation schemes employing the new constellation sets, obtained by our new signal constellation design algorithm, outperform corresponding QAM constellations significantly in terms of transmission distance and have better nonlinearity tolerance.

Relationships between Social Cognition and Sibling Constellations.

Science.gov (United States)

Goebel, Barbara L.

1985-01-01

First and second born college students (N=178) responded to measures of four social cognition factors. Multivariate analysis of variance identified relationships of social cognition factors with five sibling constellation components: subject's sex, subject's birth order (first or second), adjacent first or second born sibling's sex, spacing…

77 FR 11168 - In the Matter of Exelon Corporation; Constellation Energy Group, Inc.; Nine Mile Nuclear Station...

Science.gov (United States)

2012-02-24

... and NPF-69] In the Matter of Exelon Corporation; Constellation Energy Group, Inc.; Nine Mile Nuclear..., LLC (Exelon Ventures), and Constellation Energy Nuclear Group, LLC (CENG), acting on behalf of itself... Nuclear Advisory Committee of Constellation Energy Nuclear Group, LLC, shall prepare an Annual Report...

Constellation Map: Downstream visualization and interpretation of gene set enrichment results [version 1; referees: 2 approved

Directory of Open Access Journals (Sweden)

Yan Tan

2015-06-01

Full Text Available Summary: Gene set enrichment analysis (GSEA approaches are widely used to identify coordinately regulated genes associated with phenotypes of interest. Here, we present Constellation Map, a tool to visualize and interpret the results when enrichment analyses yield a long list of significantly enriched gene sets. Constellation Map identifies commonalities that explain the enrichment of multiple top-scoring gene sets and maps the relationships between them. Constellation Map can help investigators take full advantage of GSEA and facilitates the biological interpretation of enrichment results. Availability: Constellation Map is freely available as a GenePattern module at http://www.genepattern.org.

A platform for communicating construction material information between e-commerce systems

Institute of Scientific and Technical Information of China (English)

Stephen C W Kong; LI Heng; SHEN Qi-ping

2004-01-01

E-commerce systems for construction material procurement are becoming increasingly important in Hong Kong. These E-commerce systems are non-interoperable and create problems for the buyers who use these systems to purchase construction materials. This paper presents the mobile agent-based approach and Web serv-ices-based approach for enabling interoperation of these systems in the E-Union environment.

Development of construction materials like concrete from lunar soils without water

Science.gov (United States)

Desai, Chandra S.; Saadatmanesh, H.; Frantziskonis, G.

1989-01-01

The development of construction materials such as concrete from lunar soils without the use of water requires a different methodology than that used for conventional terrestrial concrete. A unique approach is attempted that utilizes factors such as initial vacuum and then cyclic loading to enhance the mechanical properties of dry materials similar to those available on the moon. The application of such factors is expected to allow reorientation, and coming together, of particles of the materials toward the maximum theoretical density. If such a density can provide deformation and strength properties for even a limited type of construction, the approach can have significant application potential, although other factors such as heat and chemicals may be needed for specific construction objectives.

Beyond the material grave: Life Cycle Impact Assessment of leaching from secondary materials in road and earth constructions

International Nuclear Information System (INIS)

Schwab, Oliver; Bayer, Peter; Juraske, Ronnie; Verones, Francesca; Hellweg, Stefanie

2014-01-01

Highlights: • We model environmental impacts of leaching from secondary construction material. • Industrial wastes in construction contain up to 45,000 t heavy metals per year (D). • In a scenario, 150 t are leached to the environment within 100 years after construction. • All heavy metals but As, Sb and Mo are adsorbed by 20 cm subsoil in this scenario. • Environmental impacts depend on material, pollutant, construction type, and geography. - Abstract: In industrialized countries, large amounts of mineral wastes are produced. They are re-used in various ways, particularly in road and earth constructions, substituting primary resources such as gravel. However, they may also contain pollutants, such as heavy metals, which may be leached to the groundwater. The toxic impacts of these emissions are so far often neglected within Life Cycle Assessments (LCA) of products or waste treatment services and thus, potentially large environmental impacts are currently missed. This study aims at closing this gap by assessing the ecotoxic impacts of heavy metal leaching from industrial mineral wastes in road and earth constructions. The flows of metals such as Sb, As, Pb, Cd, Cr, Cu, Mo, Ni, V and Zn originating from three typical constructions to the environment are quantified, their fate in the environment is assessed and potential ecotoxic effects evaluated. For our reference country, Germany, the industrial wastes that are applied as Granular Secondary Construction Material (GSCM) carry more than 45,000 t of diverse heavy metals per year. Depending on the material quality and construction type applied, up to 150 t of heavy metals may leach to the environment within the first 100 years after construction. Heavy metal retardation in subsoil can potentially reduce the fate to groundwater by up to 100%. One major challenge of integrating leaching from constructions into macro-scale LCA frameworks is the high variability in micro-scale technical and geographical factors

Beyond the material grave: Life Cycle Impact Assessment of leaching from secondary materials in road and earth constructions

Energy Technology Data Exchange (ETDEWEB)

Schwab, Oliver [Swiss Federal Institute of Technology Zurich, Institute of Environmental Engineering, John-von-Neumann-Weg 9, 8093 Zurich (Switzerland); Karlsruhe Institute of Technology, Institute for Geography and Geoecology, Adenauerring 20, 76131 Karlsruhe (Germany); Bayer, Peter, E-mail: bayer@erdw.ethz.ch [Swiss Federal Institute of Technology Zurich, Geological Institute, Sonneggstrasse 5, 8092 Zurich (Switzerland); Juraske, Ronnie [Swiss Federal Institute of Technology Zurich, Institute of Environmental Engineering, John-von-Neumann-Weg 9, 8093 Zurich (Switzerland); Verones, Francesca [Swiss Federal Institute of Technology Zurich, Institute of Environmental Engineering, John-von-Neumann-Weg 9, 8093 Zurich (Switzerland); Department of Environmental Science, Institute for Water and Wetland Research, Radboud University Nijmegen, P.O. Box 9010, 6500 GL Nijmegen (Netherlands); Hellweg, Stefanie [Swiss Federal Institute of Technology Zurich, Institute of Environmental Engineering, John-von-Neumann-Weg 9, 8093 Zurich (Switzerland)

2014-10-15

Highlights: • We model environmental impacts of leaching from secondary construction material. • Industrial wastes in construction contain up to 45,000 t heavy metals per year (D). • In a scenario, 150 t are leached to the environment within 100 years after construction. • All heavy metals but As, Sb and Mo are adsorbed by 20 cm subsoil in this scenario. • Environmental impacts depend on material, pollutant, construction type, and geography. - Abstract: In industrialized countries, large amounts of mineral wastes are produced. They are re-used in various ways, particularly in road and earth constructions, substituting primary resources such as gravel. However, they may also contain pollutants, such as heavy metals, which may be leached to the groundwater. The toxic impacts of these emissions are so far often neglected within Life Cycle Assessments (LCA) of products or waste treatment services and thus, potentially large environmental impacts are currently missed. This study aims at closing this gap by assessing the ecotoxic impacts of heavy metal leaching from industrial mineral wastes in road and earth constructions. The flows of metals such as Sb, As, Pb, Cd, Cr, Cu, Mo, Ni, V and Zn originating from three typical constructions to the environment are quantified, their fate in the environment is assessed and potential ecotoxic effects evaluated. For our reference country, Germany, the industrial wastes that are applied as Granular Secondary Construction Material (GSCM) carry more than 45,000 t of diverse heavy metals per year. Depending on the material quality and construction type applied, up to 150 t of heavy metals may leach to the environment within the first 100 years after construction. Heavy metal retardation in subsoil can potentially reduce the fate to groundwater by up to 100%. One major challenge of integrating leaching from constructions into macro-scale LCA frameworks is the high variability in micro-scale technical and geographical factors

The NASA CYGNSS Small Satellite Constellation

Science.gov (United States)

Ruf, C. S.; Gleason, S.; McKague, D. S.; Rose, R.; Scherrer, J.

2017-12-01

The NASA Cyclone Global Navigation Satellite System (CYGNSS) is a constellation of eight microsatellite observatories that was launched into a low (35°) inclination, low Earth orbit on 15 December 2016. Each observatory carries a 4-channel GNSS-R bistatic radar receiver. The radars are tuned to receive the L1 signals transmitted by GPS satellites, from which near-surface ocean wind speed is estimated. The mission architecture is designed to improve the temporal sampling of winds in tropical cyclones (TCs). The 32 receive channels of the complete CYGNSS constellation, combined with the 30 GPS satellite transmitters, results in a revisit time for sampling of the wind of 2.8 hours (median) and 7.2 hours (mean) at all locations between 38 deg North and 38 deg South latitude. Operation at the GPS L1 frequency of 1575 MHz allows for wind measurements in the TC inner core that are often obscured from other spaceborne remote sensing instruments by intense precipitation in the eye wall and inner rain bands. An overview of the CYGNSS mission wil be presented, followed by early on-orbit status and results.

46 CFR 58.50-15 - Alternate material for construction of independent fuel tanks.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Alternate material for construction of independent fuel...) MARINE ENGINEERING MAIN AND AUXILIARY MACHINERY AND RELATED SYSTEMS Independent Fuel Tanks § 58.50-15 Alternate material for construction of independent fuel tanks. (a) Materials other than those specifically...

Utilization of Construction Waste Composite Powder Materials as Cementitious Materials in Small-Scale Prefabricated Concrete

Directory of Open Access Journals (Sweden)

Cuizhen Xue

2016-01-01

Full Text Available The construction and demolition wastes have increased rapidly due to the prosperity of infrastructure construction. For the sake of effectively reusing construction wastes, this paper studied the potential use of construction waste composite powder material (CWCPM as cementitious materials in small-scale prefabricated concretes. Three types of such concretes, namely, C20, C25, and C30, were selected to investigate the influences of CWCPM on their working performances, mechanical properties, and antipermeability and antifrost performances. Also the effects of CWCPM on the morphology, hydration products, and pore structure characteristics of the cement-based materials were analyzed. The results are encouraging. Although CWCPM slightly decreases the mechanical properties of the C20 concrete and the 7 d compressive strengths of the C25 and C30 concretes, the 28 d compressive strength and the 90 d flexural strength of the C25 and C30 concretes are improved when CWCPM has a dosage less than 30%; CWCPM improves the antipermeability and antifrost performances of the concretes due to its filling and pozzolanic effects; the best improvement is obtained at CWCPM dosage of 30%; CWCPM optimizes cement hydration products, refines concrete pore structure, and gives rise to reasonable pore size distribution, therefore significantly improving the durability of the concretes.

29 CFR 779.336 - Sales of building materials for commercial property construction.

Science.gov (United States)

2010-07-01

... property construction. Sales of building materials to a contractor or speculative builder for the... 29 Labor 3 2010-07-01 2010-07-01 false Sales of building materials for commercial property construction. 779.336 Section 779.336 Labor Regulations Relating to Labor (Continued) WAGE AND HOUR DIVISION...

A primer on wood as dock construction material

Science.gov (United States)

Stan Lebow

2007-01-01

To be a successful marina owner and operator, it’s important to understand all the facets of one’s facility, including the intricacies of one part of the marina that most boaters take for granted: the docks. When it comes to dock construction, marinas have a wide-range of materials to choose from, with one of the most commonly used materials being preservative-treated...

Methodology for the Assessment of the Ecotoxicological Potential of Construction Materials

Science.gov (United States)

Rodrigues, Patrícia; Silvestre, José D.; Flores-Colen, Inês; Viegas, Cristina A.; de Brito, Jorge; Kurad, Rawaz; Demertzi, Martha

2017-01-01

Innovation in construction materials (CM) implies changing their composition by incorporating raw materials, usually non-traditional ones, which confer the desired characteristics. However, this practice may have unknown risks. This paper discusses the ecotoxicological potential associated with raw and construction materials, and proposes and applies a methodology for the assessment of their ecotoxicological potential. This methodology is based on existing laws, such as Regulation (European Commission) No. 1907/2006 (REACH—Registration, Evaluation, Authorization and Restriction of Chemicals) and Regulation (European Commission) No. 1272/2008 (CLP—Classification, Labelling and Packaging). Its application and validation showed that raw material without clear evidence of ecotoxicological potential, but with some ability to release chemicals, can lead to the formulation of a CM with a slightly lower hazardousness in terms of chemical characterization despite a slightly higher ecotoxicological potential than the raw materials. The proposed methodology can be a useful tool for the development and manufacturing of products and the design choice of the most appropriate CM, aiming at the reduction of their environmental impact and contributing to construction sustainability. PMID:28773011

Methodology for the Assessment of the Ecotoxicological Potential of Construction Materials.

Science.gov (United States)

Rodrigues, Patrícia; Silvestre, José D; Flores-Colen, Inês; Viegas, Cristina A; de Brito, Jorge; Kurad, Rawaz; Demertzi, Martha

2017-06-13

Innovation in construction materials (CM) implies changing their composition by incorporating raw materials, usually non-traditional ones, which confer the desired characteristics. However, this practice may have unknown risks. This paper discusses the ecotoxicological potential associated with raw and construction materials, and proposes and applies a methodology for the assessment of their ecotoxicological potential. This methodology is based on existing laws, such as Regulation (European Commission) No. 1907/2006 (REACH-Registration, Evaluation, Authorization and Restriction of Chemicals) and Regulation (European Commission) No. 1272/2008 (CLP-Classification, Labelling and Packaging). Its application and validation showed that raw material without clear evidence of ecotoxicological potential, but with some ability to release chemicals, can lead to the formulation of a CM with a slightly lower hazardousness in terms of chemical characterization despite a slightly higher ecotoxicological potential than the raw materials. The proposed methodology can be a useful tool for the development and manufacturing of products and the design choice of the most appropriate CM, aiming at the reduction of their environmental impact and contributing to construction sustainability.

Scheduling algorithms for rapid imaging using agile Cubesat constellations

Science.gov (United States)

Nag, Sreeja; Li, Alan S.; Merrick, James H.

2018-02-01

Distributed Space Missions such as formation flight and constellations, are being recognized as important Earth Observation solutions to increase measurement samples over space and time. Cubesats are increasing in size (27U, ∼40 kg in development) with increasing capabilities to host imager payloads. Given the precise attitude control systems emerging in the commercial market, Cubesats now have the ability to slew and capture images within short notice. We propose a modular framework that combines orbital mechanics, attitude control and scheduling optimization to plan the time-varying, full-body orientation of agile Cubesats in a constellation such that they maximize the number of observed images and observation time, within the constraints of Cubesat hardware specifications. The attitude control strategy combines bang-bang and PD control, with constraints such as power consumption, response time, and stability factored into the optimality computations and a possible extension to PID control to account for disturbances. Schedule optimization is performed using dynamic programming with two levels of heuristics, verified and improved upon using mixed integer linear programming. The automated scheduler is expected to run on ground station resources and the resultant schedules uplinked to the satellites for execution, however it can be adapted for onboard scheduling, contingent on Cubesat hardware and software upgrades. The framework is generalizable over small steerable spacecraft, sensor specifications, imaging objectives and regions of interest, and is demonstrated using multiple 20 kg satellites in Low Earth Orbit for two case studies - rapid imaging of Landsat's land and coastal images and extended imaging of global, warm water coral reefs. The proposed algorithm captures up to 161% more Landsat images than nadir-pointing sensors with the same field of view, on a 2-satellite constellation over a 12-h simulation. Integer programming was able to verify that

Design and construction of the Fuels and Materials Examination Facility

International Nuclear Information System (INIS)

Burgess, C.A.

1979-01-01

Final design is more than 85 percent complete on the Fuels and Materials Examination Facility, the facility for post-irradiation examination of the fuels and materials tests irradiated in the FFTF and for fuel process development, experimental test pin fabrication and supporting storage, assay, and analytical chemistry functions. The overall facility is generally described with specific information given on some of the design features. Construction has been initiated and more than 10% of the construction contracts have been awarded on a fixed price basis

7 CFR 1717.605 - Design standards, plans and specifications, construction standards, and RUS accepted materials.

Science.gov (United States)

2010-01-01

..., construction standards, and RUS accepted materials. 1717.605 Section 1717.605 Agriculture Regulations of the... standards, plans and specifications, construction standards, and RUS accepted materials. All borrowers... system design, construction standards, and the use of RUS accepted materials. Borrowers must comply with...

77 FR 23117 - Rigging Equipment for Material Handling Construction Standard; Correction and Technical Amendment

Science.gov (United States)

2012-04-18

... Equipment for Material Handling Construction Standard; Correction and Technical Amendment AGENCY... AND HEALTH REGULATIONS FOR CONSTRUCTION Subpart H--Materials Handling, Storage, Use, and Disposal 0 1... amendment. SUMMARY: OSHA is correcting its sling standard for construction titled ``Rigging Equipment for...

Alternatives to Conventional Construction Materials on Landfills. A Guide; Alternativa konstruktionsmaterial paa deponier. Vaegledning

Energy Technology Data Exchange (ETDEWEB)

Rihm, Thomas; Rogbeck, Yvonne; Svedberg, Bo; Eriksson, Maria

2009-03-15

Before a landfill can be sited, an application for a permit from the authorities is required. Already in the application process the consequences concerning impact on human health and on the environment must be described, including descriptions of e.g. bottom liners and capping constructions. Since there is a long period of time between when the permit is given and when the capping will be carried out, it is common practice, either to postpone decisions concerning capping details, or to delegate the decisions to the supervisory authorities to be made at a later stage. All constructions must however be approved by the authorities before they can be carried out. A construction must fulfil the demands for its function. For the capping this means that the percolation through it must be low, even in a long time perspective. A construction may not in itself cause adverse environmental effects, e.g. leaching of hazardous substances from the construction material. Thus, there are functional as well as environmental demands. Beside the functional demands given in the Swedish legislation, notably in the ordinance on landfilling, the construction must be physically stable, also in a long time perspective. The materials in the construction must have sufficient strength, and may not change over time, e.g. due to degradation, which could lead to malfunction. Demands on environmental behaviour can be divided into two parts. Humans and animals must be kept from direct contact with dangerous substances including dermal contact, inhalation of dust or gases and oral intake of soil, plants or berries. Secondly, dangerous substances may not be spread with surface or ground water to an extent that could lead to adverse effects on human health or on the environment. The impact on the environment is not only depending of the materials being used, but also on the construction design, where in the landfill the construction is situated and, not least, how the landfill is located. It is

Human Activity Recognition Using Hierarchically-Mined Feature Constellations

NARCIS (Netherlands)

Oikonomopoulos, A.; Pantic, Maja

In this paper we address the problem of human activity modelling and recognition by means of a hierarchical representation of mined dense spatiotemporal features. At each level of the hierarchy, the proposed method selects feature constellations that are increasingly discriminative and

End-to-End Trade-space Analysis for Designing Constellation Missions

Science.gov (United States)

LeMoigne, J.; Dabney, P.; Foreman, V.; Grogan, P.; Hache, S.; Holland, M. P.; Hughes, S. P.; Nag, S.; Siddiqi, A.

2017-12-01

Multipoint measurement missions can provide a significant advancement in science return and this science interest coupled with many recent technological advances are driving a growing trend in exploring distributed architectures for future NASA missions. Distributed Spacecraft Missions (DSMs) leverage multiple spacecraft to achieve one or more common goals. In particular, a constellation is the most general form of DSM with two or more spacecraft placed into specific orbit(s) for the purpose of serving a common objective (e.g., CYGNSS). Because a DSM architectural trade-space includes both monolithic and distributed design variables, DSM optimization is a large and complex problem with multiple conflicting objectives. Over the last two years, our team has been developing a Trade-space Analysis Tool for Constellations (TAT-C), implemented in common programming languages for pre-Phase A constellation mission analysis. By evaluating alternative mission architectures, TAT-C seeks to minimize cost and maximize performance for pre-defined science goals. This presentation will describe the overall architecture of TAT-C including: a User Interface (UI) at several levels of details and user expertise; Trade-space Search Requests that are created from the Science requirements gathered by the UI and validated by a Knowledge Base; a Knowledge Base to compare the current requests to prior mission concepts to potentially prune the trade-space; a Trade-space Search Iterator which, with inputs from the Knowledge Base, and, in collaboration with the Orbit & Coverage, Reduction & Metrics, and Cost& Risk modules, generates multiple potential architectures and their associated characteristics. TAT-C leverages the use of the Goddard Mission Analysis Tool (GMAT) to compute coverage and ancillary data, modeling orbits to balance accuracy and performance. The current version includes uniform and non-uniform Walker constellations as well as Ad-Hoc and precessing constellations, and its

Autonomous Scheduling Requirements for Agile Cubesat Constellations in Earth Observation

Science.gov (United States)

Nag, S.; Li, A. S. X.; Kumar, S.

2017-12-01

Distributed Space Missions such as formation flight and constellations, are being recognized as important Earth Observation solutions to increase measurement samples over space and time. Cubesats are increasing in size (27U, 40 kg) with increasing capabilities to host imager payloads. Given the precise attitude control systems emerging commercially, Cubesats now have the ability to slew and capture images within short notice. Prior literature has demonstrated a modular framework that combines orbital mechanics, attitude control and scheduling optimization to plan the time-varying orientation of agile Cubesats in a constellation such that they maximize the number of observed images, within the constraints of hardware specs. Schedule optimization is performed on the ground autonomously, using dynamic programming with two levels of heuristics, verified and improved upon using mixed integer linear programming. Our algorithm-in-the-loop simulation applied to Landsat's use case, captured up to 161% more Landsat images than nadir-pointing sensors with the same field of view, on a 2-satellite constellation over a 12-hour simulation. In this paper, we will derive the requirements for the above algorithm to run onboard small satellites such that the constellation can make time-sensitive decisions to slew and capture images autonomously, without ground support. We will apply the above autonomous algorithm to a time critical use case - monitoring of precipitation and subsequent effects on floods, landslides and soil moisture, as quantified by the NASA Unified Weather Research and Forecasting Model. Since the latency between these event occurrences is quite low, they make a strong case for autonomous decisions among satellites in a constellation. The algorithm can be implemented in the Plan Execution Interchange Language - NASA's open source technology for automation, used to operate the International Space Station and LADEE's in flight software - enabling a controller

Development of apparatus and procedures for evaluating radon-resistant construction materials

International Nuclear Information System (INIS)

Pugh, T.D.; Greenfield, M.B.; MacKenzie, J.; Meijer, R.J. de

1992-01-01

Laboratory facilities and apparatus have been constructed to measure radon exhalation from, and radon permeability through, various construction materials. This phase of the project has focused on development of test apparatus and evaluation of instrumentation. Results indicate significant spatial variability in the radon permeability of polyethylene, even when all test samples were selected from the same roll of material, and when no visible differentiation could be made regarding sample quality. Implications for code enforcement are described, and recommendations are offered for refinement of equipment and the measurement process, prioritization of future materials testing, and specific building code provisions, based on our results

APM for a Constellation Intersatellite Link - EM Qualification and Lessons Learned

Science.gov (United States)

Hartel, Frank; Kozilek, Horst

2016-01-01

For an Intersatellite Link (ISL) of a future constellation program, a study phase was initiated by ESA to design a mechanism for Radio Frequency communication. Airbus DS Friedrichshafen (ADSF) proposed a design based on the Antenna Pointing Mechanism (APM) family with modifications that met the stated needs of the constellation. A qualification program was started beginning in September 2015 to verify the launch and thermal loads and the equipment performance (Radio Frequency, Pointing, Microvibration and Magnetic Moment). Technical challenges identified with the Engineering Model will be discussed within this paper.

77 FR 11169 - In the Matter of Exelon Corporation; Constellation Energy Group, Inc.; R.E. Ginna Nuclear Power...

Science.gov (United States)

2012-02-24

... Constellation Energy Nuclear Group, LLC (CENG), acting on behalf of itself, and the licensee, requested that the... Constellation Energy Nuclear Group, LLC, shall prepare an Annual Report regarding the status of foreign... or part, of Constellation Energy Nuclear Group, LLC. The Report shall be submitted to the NRC within...

Leaching of additives from construction materials to urban storm water runoff.

Science.gov (United States)

Burkhardt, M; Zuleeg, S; Vonbank, R; Schmid, P; Hean, S; Lamani, X; Bester, K; Boller, M

2011-01-01

Urban water management requires further clarification about pollutants in storm water. Little is known about the release of organic additives used in construction materials and the impact of these compounds to storm water runoff. We investigated sources and pathways of additives used in construction materials, i.e., biocides in facades' render as well as root protection products in bitumen membranes for rooftops. Under wet-weather conditions, the concentrations of diuron, terbutryn, carbendazim, irgarol 1051 (all from facades) and mecoprop in storm water and receiving water exceeded the predicted no-effect concentrations values and the Swiss water quality standard of 0.1 microg/L. Under laboratory conditions maximum concentrations of additives were in the range of a few milligrams and a few hundred micrograms per litre in runoff of facades and bitumen membranes. Runoff from aged materials shows approximately one to two orders of magnitude lower concentrations. Concentrations decreased also during individual runoff events. In storm water and receiving water the occurrence of additives did not follow the typical first flush model. This can be explained by the release lasting over the time of rainfall and the complexity of the drainage network. Beside the amounts used, the impact of construction materials containing hazardous additives on water quality is related clearly to the age of the buildings and the separated sewer network. The development of improved products regarding release of hazardous additives is the most efficient way of reducing the pollutant load from construction materials in storm water runoff.

Adaptation and Re-Use of Spacecraft Power System Models for the Constellation Program

Science.gov (United States)

Hojnicki, Jeffrey S.; Kerslake, Thomas W.; Ayres, Mark; Han, Augustina H.; Adamson, Adrian M.

2008-01-01

NASA's Constellation Program is embarking on a new era of space exploration, returning to the Moon and beyond. The Constellation architecture will consist of a number of new spacecraft elements, including the Orion crew exploration vehicle, the Altair lunar lander, and the Ares family of launch vehicles. Each of these new spacecraft elements will need an electric power system, and those power systems will need to be designed to fulfill unique mission objectives and to survive the unique environments encountered on a lunar exploration mission. As with any new spacecraft power system development, preliminary design work will rely heavily on analysis to select the proper power technologies, size the power system components, and predict the system performance throughout the required mission profile. Constellation projects have the advantage of leveraging power system modeling developments from other recent programs such as the International Space Station (ISS) and the Mars Exploration Program. These programs have developed mature power system modeling tools, which can be quickly modified to meet the unique needs of Constellation, and thus provide a rapid capability for detailed power system modeling that otherwise would not exist.

Advantages and challenges of dissimilar materials in automotive lightweight construction

Science.gov (United States)

Weberpals, Jan-Philipp; Schmidt, Philipp A.; Böhm, Daniel; Müller, Steffen

2015-03-01

The core of future automotive lightweight materials is the joining technology of various material mixes. The type of joining will be essential, particularly in electrified propulsion systems, especially as an improved electrical energy transmission leads to a higher total efficiency of the vehicle. The most evident parts to start the optimization process are the traction battery, the electrical performance modules and the engines. Consequently aluminum plays a very central role for lightweight construction applications. However, the physical-technical requirements of components often require the combination with other materials. Thus the joining of mixed material connections is an essential key technology for many of the current developments, for example in the areas E-Mobility, solar energy and lightweight construction. Due to these advantages mixed material joints are already established in the automotive industry and laser beam remote welding is now a focus technology for mixed material connections. The secret of the laser welding process with mixed materials lies within the different areas of the melting phase diagram depending on the mixing ratio and the cooling down rate. According to that areas with unwanted, prim, intermetallic phases arise in the fusion zone. Therefore, laser welding of mixed material connections can currently only be used with additional filler in the automotive industry.

Case Study: LCA Methodology Applied to Materials Management in a Brazilian Residential Construction Site

Directory of Open Access Journals (Sweden)

João de Lassio

2016-01-01

Full Text Available The construction industry is increasingly concerned with improving the social, economic, and environmental indicators of sustainability. More than ever, the growing demand for construction materials reflects increased consumption of raw materials and energy, particularly during the phases of extraction, processing, and transportation of materials. This work aims to help decision-makers and to promote life cycle thinking in the construction industry. For this purpose, the life cycle assessment (LCA methodology was chosen to analyze the environmental impacts of building materials used in the construction of a residence project in São Gonçalo, Rio de Janeiro, Brazil. The LCA methodology, based on ISO 14040 and ISO 14044 guidelines, is applied with available databases and the SimaPro program. As a result, this work shows that there is a substantial waste of nonrenewable energy, increasing global warming and harm to human health in this type of construction. This study also points out that, for this type of Brazilian construction, ceramic materials account for a high percentage of the mass of a total building and are thus responsible for the majority of environmental impacts.

An analytical framework for common-pool resource–large technical system (CPR-LTS constellations

Directory of Open Access Journals (Sweden)

Pär Blomkvist

2013-02-01

Full Text Available This paper introduces an analytical framework for a special phenomenon: when a common-pool resource (CPR institution and a large technical system (LTS are connected and mutually interdependent. The CPR in this case is a node managed by its appropriators within a centrally planned and managed system; here named CPR-LTS constellations. Our framework is empirically derived from two historical investigations of CPR institutions within two LTSs, the agricultural-technical system and the road transport system of Sweden. By comparing similarities and differences it is possible to identify paths to successes and failures. To understand why one survived and the other disappeared we connect Elinor Ostrom’s theories about management of CPRs with Thomas P. Hughes’s theories about LTSs. We are proposing a framework that can bridge the gap between theories about management of CPRs and LTSs. By combining the two theories it should be possible to better understand how small-scale producers using bottom-up CPRs can be linked to top-down LTSs.We will argue that to fit within an LTS, a CPR needs alignment between different parts or components within the constellation/system and alignment with other systems and institutions in society. We propose three analytical levels to deal with the phenomenon of aligning a CPR project to an existing, large sociotechnical system:Local alignment (CPR: How are CPRs organized and managed at local sites?Sociotechnical alignment (CPR-LTS: How are CPRs connected to the sociotechnical system?Contextual alignment: How are CPR-LTS constellations aligned with neighboring institutions and systems in society?Our work indicates that for successful management of a CPR-LTS constellation it is important that the CPR be included in legislation and that government agencies support the CPR in alignment with the LTS. Legislators must recognize the CPR-part in the CPR-LTS constellation so that its institutional body is firmly established in

Characterizing material properties of cement-stabilized rammed earth to construct sustainable insulated walls

Directory of Open Access Journals (Sweden)

Rishi Gupta

2014-01-01

Full Text Available Use of local materials can reduce the hauling of construction materials over long distances, thus reducing the greenhouse gas emissions associated with transporting such materials. Use of locally available soils (earth for construction of walls has been used in many parts of the world. Owing to the thermal mass of these walls and the potential to have insulation embedded in the wall section has brought this construction material/technology at the forefront in recent years. However, the mechanical properties of the rammed earth and the parameters required for design of steel reinforced walls are not fully understood. In this paper, the author presents a case study where full-scale walls were constructed using rammed earth to understand the effect of two different types of shear detailing on the structural performance of the walls. The mechanical properties of the material essential for design such as compressive strength of the material including effect of coring on the strength, pull out strength of different rebar diameters, flexural performance and out-of-plane bending on walls was studied. These results are presented in this case study.

Role of coal combustion products in sustainable construction materials

Energy Technology Data Exchange (ETDEWEB)

Naik, T.R.; Siddique, R.; Vaniker, S. [University of Wisconsin-Milwaukee, Milwaukee, WI (USA). UWM Center for Products Utilization, College of Engineering and Applied Science

2003-07-01

The paper describes various coal combustion products, CCPs produced in the process of power generation. These include fly ash, bottom ash, boiler slag and flue gas desulfurization products. Typical test protocol used for testing, analysis and evaluation of CCPs, as well as the current best recycling use options for these materials are discussed. Materials, productions, properties, and potential applications in the manufacture of emerging materials for sustainable construction, as well as environmental impact are also briefly discussed. 47 refs., 16 figs., 8 tabs.

High-density arrays of x-ray microcalorimeters for Constellation-X

Science.gov (United States)

Kilbourne, Caroline A.; Bandler, Simon R.; Brown, Ari D.; Chervenak, James A.; Figueroa-Feliciano, Enectali; Finkbeiner, Fred M.; Iyomoto, Naoko; Kelley, Richard L.; Porter, F. Scott; Saab, Tarek; Sadleir, John; White, Jennifer

2006-06-01

We have been developing x-ray microcalorimeters for the Constellation-X mission. Devices based on superconducting transition-edge sensors (TES) have demonstrated the potential to meet the Constellation-X requirements for spectral resolution, speed, and array scale (> 1000 pixels) in a close-packed geometry. In our part of the GSFC/NIST collaboration on this technology development, we have been concentrating on the fabrication of arrays of pixels suitable for the Constellation-X reference configuration. We have fabricated 8x8 arrays with 0.25-mm pixels arranged with 92% fill factor. The pixels are based on Mo/Au TES and Bi/Cu or Au/Bi absorbers. We have achieved a resolution of 4.0 eV FWHM at 6 keV in such devices, which meets the Constellation-X resolution requirement at 6 keV. Studies of the thermal transport in our Bi/Cu absorbers have shown that, while there is room for improvement, for 0.25-mm pixels the standard absorber design is adequate to avoid unacceptable line-broadening from position dependence caused by thermal diffusion. In order to improve reproducibility and to push closer to the 2-eV goal at 6 keV, however, we are refining the design of the TES and the interface to the absorber. Recent efforts to introduce a barrier layer between the Bi and the Mo/Au to avoid variable interface chemistry and thus improve the reproducibility of device characteristics have thus far yielded unsatisfactory results. However, we have developed a new set of absorber designs with contacts to the TES engineered to allow contact only in regions that do not serve as the active thermometer. We have further constrained the design so that a low-resistance absorber will not electrically short the TES. It is with such a design that we have achieved 4.0 eV resolution at 6 keV.

Meta-analysis of the antecedent and consequent constructs of materialism

Directory of Open Access Journals (Sweden)

Fernando de Oliveira Santini

2017-10-01

Full Text Available Purpose – Materialism has been gaining ground in the academic field, especially from the 1980s on, given the relevance of understanding sentiments connected to possessing and acquiring goods. Thus, this meta-analysis was carried out to assess the antecedents and consequents of materialism. Design/methodology/approach – Based on a systematic review, we gathered a total 77 articles that examined those aspects, generating 99 effects-sizes and a cumulative sample of 40,288 studied individuals. Findings – The antecedents of materialism that showed a significant relationship with this construct were: perceived hedonic value, interpersonal influence, life satisfaction, and income. As for the consequents, we observed significance for purchase intention, impulsive buying, compulsive buying, conspicuous consumption, status consumption, and consumer involvement. Regarding the moderating effect, we observed that small samples produce greater effects. Furthermore, for the relationship between materialism and purchase intention, there are stronger effects for surveys conducted in Western countries. Originality/value – Based on the methodology applied in this study, we expected a solid and generalizable contribution regarding construct materialism.

Going Beyond Einstein with the Constellation-X Mission

Science.gov (United States)

White, Nicholas

2007-01-01

The Constellation-X mission will address the questions: "What happens to matter close to a black hole?" and "What is Dark Energy?" These questions are central to the NASA Beyond Einstein Program, where Constellation-X plays a central role. The mission will address these questions by using high throughput X-ray spectroscopy to observe the effects of strong gravity close to the event horizon of black holes, and to observe the formation and evolution of clusters of galaxies in order to precisely determine Cosmological parameters. To achieve these primary science goals requires a factor of 25-100 increase in sensitivity for high resolution X-ray spectroscopy.'The mission will also perform routine high-resolution X-ray spectroscopy of faint 2nd extended X-ray source populations. This will provide diagnostic information such as density, elemental abundances, velocity; and ionization state for a wide range of astrophysical problems, including new constraints on the Neutron Star equation of state.

Unvulcanized elastomeric waterproofing materials for construction application

Directory of Open Access Journals (Sweden)

O. V. Karmanova

2016-01-01

Full Text Available In the construction was widespread elastomer profiles, which have the ability to swell in water. Such products should have a high capacity for swelling, elasticity, resistance to weathering. At the present time for these purposes are used materials, mostly of foreign origin. With the increasing pace of construction in Russia the problem of replacement of imported materials is particularly relevant. The work was dedicated to the creation of water-swellable elastomer materials using bentonite powders and study of their properties. Сomparative testing of imported and domestic hydrophilic sealants were held. Rationale and choice of components for the cords of bentonite was conducted. Polymer base is saturated ethylene-propylene rubber. Bentonite from different manufacturers used to increase the swelling of the samples. Filler added in an amount of 50–100 phr. The elastomeric compositions were prepared using laboratory roller at a temperature of 60 ± 5° C. Profiling was performed on a syringe-machine at a temperature of 120° C. Extrusion indicator of the mixtures were evaluated on a 10-point scale (German-Russian system. It is found that high swelling products provided using field Azerbaijan bentonite. It is noted that the dosage of bentonite than 150 w.p. deteriorates technological properties of bentonite cords. It has been shown that activation of the bentonite and sodium carbonate chloride can significantly improve product swelling, wherein the bentonite content of the composition was 150–200 w.p.

78 FR 32385 - Exelon Generation Company, LLC; CER Generation II, LLC; Constellation Mystic Power, LLC...

Science.gov (United States)

2013-05-30

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. EL13-64-000] Exelon Generation Company, LLC; CER Generation II, LLC; Constellation Mystic Power, LLC; Constellation NewEnergy...) Rules of Practice and Procedure, 18 CFR 385.207, Exelon Generation Company, LLC, CER Generation II, LLC...

Raw material selection for object construction

CSIR Research Space (South Africa)

Perlow, J

2017-11-01

Full Text Available on their visual appearance. In particular, we present a method for an agent to recognise the required unseen raw material images and link them to corresponding novel object images. This capability provides an agent with an increased degree of resourcefulness... construction from component parts, and in doing so we provide a benchmark for future work to compare against within Minecraft and ShapeNet domains. II. BACKGROUND Our model is inspired by Siamese neural networks, a class of neural network that includes multiple...

Expanding Application of Perforated Metal Materials in Construction and Architecture

Science.gov (United States)

Mironovs, V.; Tatarinov, A.; Gorbacova, S.

2017-10-01

Perforated metal materials (PMM) combine a range of properties, including rigidity, strength, lightweight, small thickness, a dosed transparency and decorative attractiveness. All these bring new application effects in construction industry and architecture. Nowadays, PMM are widely used in design of facades and interiors all over the world, becoming more popular in Latvia as well. The paper touches several aspects of PMM applications, including its decoration function, shadowing of sunlight, sound and noise barrier function and the problem of corrosion when exploited outdoors. Possible perfection may include using different coatings, multi-layer design variants and integration with other constructional materials in order to provide better sound absorption, corrosion resistance and functionality.

Drivers militating against the pricing of sustainable construction materials: The Ghanaian quantity surveyors perspective

Directory of Open Access Journals (Sweden)

Ernest Kissi

2018-06-01

Full Text Available Sustainability has in recent times attained much acceptance as a result of its positive impact on the environment, social and economic issues. Nevertheless, in developing countries, the price of sustainable construction materials are too high. The aim of the study was to examine drivers militating against the pricing of sustainable construction materials. Through an in-depth review of literature as well as an interview survey, questionnaire was designed and administered to practicing quantity surveyors. Data generated from the survey was analysed using Principal Component Analysis which resulted four main drivers. These included: awareness challenge (AC, sustainability measurement tools challenge (SMTC, economic challenge (EC, and information challenge (IC. The study offers useful lessons on sustainable practices that pricing experts in the construction industry can draw on when pricing.The need for this study cannot be doubted since the consciousness of such challenges will help in resolving issues associated with pricing of sustainable construction materials. Keywords: Drivers, Militating, Pricing, Sustainable construction materials, Ghanaian

Construction of a test embankment using a sand-tire shred mixture as fill material.

Science.gov (United States)

Yoon, Sungmin; Prezzi, Monica; Siddiki, Nayyar Zia; Kim, Bumjoo

2006-01-01

Use of tire shreds in construction projects, such as highway embankments, is becoming an accepted way of beneficially recycling scrap tires. However, in the last decade there was a decline in the use of pure tire shreds as fill materials in embankment construction, as they are susceptible to fire hazards due to the development of exothermic reactions. Tire shred-sand mixtures, on the other hand, were found to be effective in inhibiting exothermic reactions. When compared with pure tire shreds, tire shred-sand mixtures are less compressible and have higher shear strength. However, the literature contains limited information on the use of tire shred-soil mixtures as a fill material. The objectives of this paper are to discuss and evaluate the feasibility of using tire shred-sand mixtures as a fill material in embankment construction. A test embankment constructed using a 50/50 mixture, by volume, of tire shreds and sand was instrumented and monitored to: (a) determine total and differential settlements; (b) evaluate the environmental impact of the embankment construction on the groundwater quality due to leaching of fill material; and (c) study the temperature variation inside the embankment. The findings in this research indicate that mixtures of tire shreds and sand are viable materials for embankment construction.

Utilization of stabilized municipal waste combustion ash residues as construction material

International Nuclear Information System (INIS)

Shieh, C.S.

1992-01-01

Stabilized municipal waste combustion (MWC) ash residues were investigated for their potential as construction material that can be beneficially used in terrestrial and marine environments. End-use products, such as patio stones, brick pavers, solid blocks, and reef units, were fabricated and tested for their engineering and chemical characteristics. engineering feasibility and environmental acceptability of using stabilized ash residues as construction material are discussed in this paper. Ash samples were collected from two mass-burn facilities and one refuse derived fuel (RDF) facility in Florida

Supporting nurse mentor development: An exploration of developmental constellations in nursing mentorship practice.

Science.gov (United States)

MacLaren, Julie-Ann

2018-01-01

Supervised practice as a mentor is currently an integral component of nurse mentor education. However, workplace education literature tends to focus on dyadic mentor-student relationships rather than developmental relationships between colleagues. This paper explores the supportive relationships of nurses undertaking a mentorship qualification, using the novel technique of constellation development to determine the nature of workplace support for this group. Semi-structured interviews were conducted with three recently qualified nurse mentors. All participants developed a mentorship constellation identifying colleagues significant to their own learning in practice. These significant others were also interviewed alongside practice education, and nurse education leads. Constellations were analysed in relation to network size, breadth, strength of relationships, and attributes of individuals. Findings suggest that dyadic forms of supervisory mentorship may not offer the range of skills and attributes that developing mentors require. Redundancy of mentorship attributes within the constellation (overlapping attributes between members) may counteract problems caused when one mentor attempts to fulfil all mentorship roles. Wider nursing teams are well placed to provide the support and supervision required by mentors in training. Where wider and stronger networks were not available to mentorship students, mentorship learning was at risk. Crown Copyright © 2017. Published by Elsevier Ltd. All rights reserved.

48 CFR 52.225-12 - Notice of Buy American Act Requirement-Construction Materials Under Trade Agreements.

Science.gov (United States)

2010-10-01

... Requirement-Construction Materials Under Trade Agreements. 52.225-12 Section 52.225-12 Federal Acquisition...—Construction Materials Under Trade Agreements. As prescribed in 25.1102(d)(1), insert the following provision: Notice of Buy American Act Requirement—Construction Materials Under Trade Agreements (FEB 2009) (a...

The use of bio-based materials to reduce the environmental impact of construction

OpenAIRE

Lawrence, Michael

2014-01-01

In the UK, the construction industry is responsible for over 50 % of total carbon emissions. 20% of these carbon emissions are embodied within the construction and materials of buildings and the balance is expended in environmental control (heating, lighting, air conditioning) and other ‘in use’ aspects of occupation of buildings. This is replicated in other countries to a similar extent. This lecture identifies ways in which the use of bio-based construction materials can significantly reduc...

Quality and safety of construction materials

International Nuclear Information System (INIS)

Rodulfo Zabala, L.

2015-01-01

CEPCO represents 20 industrial sectors, which take charge of construction materials production, and whose expectations of European and Spanish legislation observance (specially the articles related to quality, security and environmental respect) reach a very high level. This performance is equally taken to their internal competitiveness and to their huge international enlargement produced on the recent years. In addition to this principle, the Confederation includes its own this principle, the Confederation includes its own doctrine of trying to consolidate important heights of quality related to the evolution of the product trough I+D+i. (Author)

Constellations of Next Generation Gravity Missions: Simulations regarding optimal orbits and mitigation of aliasing errors

Science.gov (United States)

Hauk, M.; Pail, R.; Gruber, T.; Purkhauser, A.

2017-12-01

The CHAMP and GRACE missions have demonstrated the tremendous potential for observing mass changes in the Earth system from space. In order to fulfil future user needs a monitoring of mass distribution and mass transport with higher spatial and temporal resolution is required. This can be achieved by a Bender-type Next Generation Gravity Mission (NGGM) consisting of a constellation of satellite pairs flying in (near-)polar and inclined orbits, respectively. For these satellite pairs the observation concept of the GRACE Follow-on mission with a laser-based low-low satellite-to-satellite tracking (ll-SST) system and more precise accelerometers and state-of-the-art star trackers is adopted. By choosing optimal orbit constellations for these satellite pairs high frequency mass variations will be observable and temporal aliasing errors from under-sampling will not be the limiting factor anymore. As part of the European Space Agency (ESA) study "ADDCON" (ADDitional CONstellation and Scientific Analysis Studies of the Next Generation Gravity Mission) a variety of mission design parameters for such constellations are investigated by full numerical simulations. These simulations aim at investigating the impact of several orbit design choices and at the mitigation of aliasing errors in the gravity field retrieval by co-parametrization for various constellations of Bender-type NGGMs. Choices for orbit design parameters such as altitude profiles during mission lifetime, length of retrieval period, value of sub-cycles and choice of prograde versus retrograde orbits are investigated as well. Results of these simulations are presented and optimal constellations for NGGM's are identified. Finally, a short outlook towards new geophysical applications like a near real time service for hydrology is given.

NASA's Constellation Program: Milestones Towards the Frontier

Science.gov (United States)

Hanley, Jeffrey M.; Thomas, Lawrence D.; Rhatigan, Jennifer L.; Boatright, Tony J.

2009-01-01

This slide presentation reviews the status and progress made in the Constellation Program's work towards the goal of lunar and Martian exploration flights. It includes views of the various components of the program, and reviews the status of the engine tests, and the development of the Ares I-X towards test launch, the Orion Crew Module, the launch abort system, and the ground operations facilities.

Cost Indexing and Unit Price Adjustments for Construction Materials

Science.gov (United States)

2012-10-30

This project was focused on the assimilation of information regarding unit price adjustment clauses, or PACs, : that are offered for construction materials at the state Departments of Transportation (DOTs). It is intended to : provide the South Carol...

A novel abutment construction technique for rapid bridge construction : controlled low strength Materials (CLSM) with full-height concrete panels.

Science.gov (United States)

2012-01-01

One of the major obstacles facing rapid bridge construction for typical span type bridges is the time required to construct bridge abutments and foundations. This can be remedied by using the controlled low strength materials (CLSM) bridge abutment. ...

Utilization of ashes as construction materials in landfills; Askanvaendning i deponier

Energy Technology Data Exchange (ETDEWEB)

Tham, Gustav [Telge AB, Soedertaelje (Sweden); Ifwer, Karin [AaF-Process AB, Stockholm (Sweden)

2006-03-15

Large amounts of material will be needed to cover landfill sites in Sweden and other EU states over the next ten years. It is estimated that more than one hundred million tons of material will be required in Sweden alone in order to comply with the EU Landfill Directive (1999/31/EC). Suitable natural materials to be used in landfill cover constructions are not available on site. This report summarises the present use of secondary construction material in waste management with a focus on incineration ash. Information from eleven landfill sites has been compiled and includes the practical experience of using ash as the primary material in landfill cover. Other applications of using ash on landfill sites are also discussed. According to Swedish law, a complete cover of a landfill site consists of five different layers, each having its own specific function. The permeability of the total cover should then satisfy the permeability requirements of 50 litres per square meter and year for non-hazardous waste landfill sites and 5 litres per square meter and year for those with hazardous waste. The main purpose of this report is to describe how ash is used in the different layers and discuss the advantages or disadvantages of the techniques applied. Various landfill sites have submitted information ranging from small test areas on a pilot scale to full scale application of techniques on several hectares. Each project is part of the general Vaermeforsk research program for 2003-2005, Environmentally proper use of ash. The overall results show that incineration ash is a suitable material for use in liner constructions, either alone, or mixed with sewage sludge. Data from water percolating below the liner has indicated that the liners can meet permeability requirements. Special techniques for applying the various layers have been described. It is important to have materials readily available for an area, in order to avoid long period of exposure to dry or wet weather. Some

Temporal Probabilistic Constellation Shaping for WDM Optical Communication Systems

DEFF Research Database (Denmark)

Yankov, Metodi Plamenov; Forchhammer, Søren

2016-01-01

Finite state machine sources transmitting QPSK are studied as input to WDM optical fiber systems with ideal distributed Raman amplification. The probabilities of successive constellation symbols are shaped for nonlinear transmission and gains of around 500km (5-10%) are demonstrated...

Temporal Probabilistic Constellation Shaping for WDM Optical Communication Systems

OpenAIRE

Yankov, Metodi Plamenov; Forchhammer, Søren

2016-01-01

Finite state machine sources transmitting QPSK are studied as input to WDM optical fiber systems with ideal distributed Raman amplification. The probabilities of successive constellation symbols are shaped for nonlinear transmission and gains of around 500km (5-10%) are demonstrated

BRITE-Constellation: Nanosatellites for precision photometry of bright stars

Science.gov (United States)

Weiss, W. W.; Moffat, A. F. J.; Schwarzenberg-Czerny, A.; Koudelka, O. F.; Grant, C. C.; Zee, R. E.; Kuschnig, R.; Mochnacki, St.; Rucinski, S. M.; Matthews, J. M.; Orleański, P.; Pamyatnykh, A. A.; Pigulski, A.; Alves, J.; Guedel, M.; Handler, G.; Wade, G. A.; Scholtz, A. L.; Scholtz

2014-02-01

BRITE-Constellation (where BRITE stands for BRIght Target Explorer) is an international nanosatellite mission to monitor photometrically, in two colours, brightness and temperature variations of stars brighter than V ~ 4, with precision and time coverage not possible from the ground. The current mission design consists of three pairs of 7 kg nanosats (hence ``Constellation'') from Austria, Canada and Poland carrying optical telescopes (3 cm aperture) and CCDs. One instrument in each pair is equipped with a blue filter; the other, a red filter. The first two nanosats (funded by Austria) are UniBRITE, designed and built by UTIAS-SFL (University of Toronto Institute for Aerospace Studies-Space Flight Laboratory) and its twin, BRITE-Austria, built by the Technical University Graz (TUG) with support of UTIAS-SFL. They were launched on 25 February 2013 by the Indian Space Agency, under contract to the Canadian Space Agency. Each BRITE instrument has a wide field of view (~ 24 degrees), so up to 15 bright stars can be observed simultaneously in 32 × 32 sub-rasters. Photometry (with reduced precision but thorough time sampling) of additional fainter targets will be possible through on-board data processing. A critical technical element of the BRITE mission is the three-axis attitude control system to stabilize a nanosat with very low inertia. The pointing stability is better than 1.5 arcminutes rms, a significant advance by UTIAS-SFL over any previous nanosatellite. BRITE-Constellation will primarily measure p- and g-mode pulsations to probe the interiors and ages of stars through asteroseismology. The BRITE sample of many of the brightest stars in the night sky is dominated by the most intrinsically luminous stars: massive stars seen at all evolutionary stages, and evolved medium-mass stars at the very end of their nuclear burning phases (cool giants and AGB stars). The Hertzsprung-Russell diagram for stars brighter than mag V=4 from which the BRITE-Constellation sample

Constellations of gaps in Eratosthenes sieve

OpenAIRE

Holt, Fred B.

2015-01-01

A few years ago we identified a recursion that works directly with the gaps among the generators in each stage of Eratosthenes sieve. This recursion provides explicit enumerations of sequences of gaps among the generators, which sequences are known as constellations. Over the last year we identified a discrete linear system that exactly models the population of any gap across all stages of the sieve. In August 2014 we summarized our results from analyzing this discrete model on populations of...

The Use Potential of Traditional Building Materials for the Realization of Structures by Modern Methods of Construction

Science.gov (United States)

Spišáková, Marcela; Mačková, Daniela

2015-11-01

The sustainable building has taken off in recent years with many investors looking for new and different methods of construction. The traditional building materials can be made out of natural materials, while others can help to lower energy costs of the occupant once built. Regardless of what the goal of the investor is, traditional building materials and their use is on the rise. The submitted paper provides an overview of natural building materials and possible modern building systems using these construction materials. Based on the questionnaire survey is defined the use potential of traditional building materials for the realization of the construction by methods of modern constructions and then are determined the drivers and barriers of traditional materials through using modern methods of construction. Considering the analysis of the achieved results, we can identify the gaps in the construction market in Slovakia and also to assess the perception of potential investors in the field of traditional building materials use, which is the purpose of submitted paper.

The Utilization of Graphene Oxide in Traditional Construction Materials: Asphalt

Directory of Open Access Journals (Sweden)

Wenbo Zeng

2017-01-01

Full Text Available In the advanced research fields of solar cell and energy storing materials, graphene and graphene oxide (GO are two of the most promising materials due to their high specific surface area, and excellent electrical and physical properties. However, they was seldom studied in the traditional materials because of their high cost. Nowadays, graphene and GO are much cheaper than before with the development of production technologies, which provides the possibility of using these extraordinary materials in the traditional construction industry. In this paper, GO was selected as a nano-material to modify two different asphalts. Then a thin film oven test and a pressure aging vessel test were applied to simulate the aging of GO-modified asphalts. After thermal aging, basic physical properties (softening point and penetration were tested for the samples which were introduced at different mass ratios of GO (1% and 3% to asphalt. In addition, rheological properties were tested to investigate how GO could influence the asphalts by dynamic shearing rheometer tests. Finally, some interesting findings and potential utilization (warm mixing and flame retardants of GO in asphalt pavement construction were explained.

The Utilization of Graphene Oxide in Traditional Construction Materials: Asphalt.

Science.gov (United States)

Zeng, Wenbo; Wu, Shaopeng; Pang, Ling; Sun, Yihan; Chen, Zongwu

2017-01-07

In the advanced research fields of solar cell and energy storing materials, graphene and graphene oxide (GO) are two of the most promising materials due to their high specific surface area, and excellent electrical and physical properties. However, they was seldom studied in the traditional materials because of their high cost. Nowadays, graphene and GO are much cheaper than before with the development of production technologies, which provides the possibility of using these extraordinary materials in the traditional construction industry. In this paper, GO was selected as a nano-material to modify two different asphalts. Then a thin film oven test and a pressure aging vessel test were applied to simulate the aging of GO-modified asphalts. After thermal aging, basic physical properties (softening point and penetration) were tested for the samples which were introduced at different mass ratios of GO (1% and 3%) to asphalt. In addition, rheological properties were tested to investigate how GO could influence the asphalts by dynamic shearing rheometer tests. Finally, some interesting findings and potential utilization (warm mixing and flame retardants) of GO in asphalt pavement construction were explained.

Approximating the constellation constrained capacity of the MIMO channel with discrete input

DEFF Research Database (Denmark)

Yankov, Metodi Plamenov; Forchhammer, Søren; Larsen, Knud J.

2015-01-01

In this paper the capacity of a Multiple Input Multiple Output (MIMO) channel is considered, subject to average power constraint, for multi-dimensional discrete input, in the case when no channel state information is available at the transmitter. We prove that when the constellation size grows, t...... for the equivalent orthogonal channel, obtained by the singular value decomposition. Furthermore, lower bounds on the constrained capacity are derived for the cases of square and tall MIMO matrix, by optimizing the constellation for the equivalent channel, obtained by QR decomposition....

The Promotion Strategy of Green Construction Materials: A Path Analysis Approach

Directory of Open Access Journals (Sweden)

Chung-Fah Huang

2015-10-01

Full Text Available As one of the major materials used in construction, cement can be very resource-consuming and polluting to produce and use. Compared with traditional cement processing methods, dry-mix mortar is more environmentally friendly by reducing waste production or carbon emissions. Despite the continuous development and promotion of green construction materials, only a few of them are accepted or widely used in the market. In addition, the majority of existing research on green construction materials focuses more on their physical or chemical characteristics than on their promotion. Without effective promotion, their benefits cannot be fully appreciated and realized. Therefore, this study is conducted to explore the promotion of dry-mix mortars, one of the green materials. This study uses both qualitative and quantitative methods. First, through a case study, the potential of reducing carbon emission is verified. Then a path analysis is conducted to verify the validity and predictability of the samples based on the technology acceptance model (TAM in this study. According to the findings of this research, to ensure better promotion results and wider application of dry-mix mortar, it is suggested that more systematic efforts be invested in promoting the usefulness and benefits of dry-mix mortar. The model developed in this study can provide helpful references for future research and promotion of other green materials.

The Promotion Strategy of Green Construction Materials: A Path Analysis Approach.

Science.gov (United States)

Huang, Chung-Fah; Chen, Jung-Lu

2015-10-14

As one of the major materials used in construction, cement can be very resource-consuming and polluting to produce and use. Compared with traditional cement processing methods, dry-mix mortar is more environmentally friendly by reducing waste production or carbon emissions. Despite the continuous development and promotion of green construction materials, only a few of them are accepted or widely used in the market. In addition, the majority of existing research on green construction materials focuses more on their physical or chemical characteristics than on their promotion. Without effective promotion, their benefits cannot be fully appreciated and realized. Therefore, this study is conducted to explore the promotion of dry-mix mortars, one of the green materials. This study uses both qualitative and quantitative methods. First, through a case study, the potential of reducing carbon emission is verified. Then a path analysis is conducted to verify the validity and predictability of the samples based on the technology acceptance model (TAM) in this study. According to the findings of this research, to ensure better promotion results and wider application of dry-mix mortar, it is suggested that more systematic efforts be invested in promoting the usefulness and benefits of dry-mix mortar. The model developed in this study can provide helpful references for future research and promotion of other green materials.

Development and mechanical properties of construction materials from lunar simulants

Science.gov (United States)

Desai, Chandra S.

1990-01-01

The development of construction materials such as concrete from lunar soils without the use of water requires a different methodology than that used for conventional terrestrial concrete. Currently, this research involves two aspects: (1) liquefaction of lunar simulants with various additives in a furnace so as to produce a construction material like an intermediate ceramic; and (2) cyclic loading of simulant with different initial vacuums and densities with respect to the theoretical maximum densities (TMD). In both cases, bending, triaxial compression, extension, and hydrostatic tests will be performed to define the stress-strain strength response of the resulting materials. In the case of the intermediate ceramic, bending and available multiaxial test devices will be used, while for the compacted case, tests will be performed directly in the new device. The tests will be performed by simulating in situ confining conditions. A preliminary review of high-purity metal is also conducted.

Review on the Traditional Uses and Potential of Totora (Schoenoplectus Californicus) as Construction Material

Science.gov (United States)

Hidalgo-Cordero, Juan Fernando; García-Navarro, Justo

2017-10-01

The recent advances in the wood construction field have demonstrated the feasibility and advantages of using wood-based materials in tall buildings structures and other constructive uses, which could lead to a net reduction in CO2eq emissions of the construction sector by replacing high-energy consuming materials like concrete or steel, with wood and biomass-based materials. Among these biomass-based materials are the Non-Timber Forest Products (NTFP)which are plantsthat canprovide important contributionsto the construction sector and help to reduce the net CO2eq emissions of the building industry. One of these plants is the totora (Schoenoplectus Californicus) that has been long used by several communities for making handicrafts and as construction material. Recent studies on this plant have analyzed its properties and its feasibility to be used for producing materials of interest to the contemporary building industry. The totora is a bulrush that grows in lakes and marshes in America from California to Chile and some of the Pacific islands. It grows from the sea level to 4500maasl, it can grow in fresh water and estuaries, and it is resistant to water level changes and drought. This bulrush has been used by many cultures as medicine, food, forage, material for building houses, boats and different handicrafts. The most important examples of the use of totora in the world are the floating islands of the Uros in Lake Titicaca. The Uros people have developed traditional techniques for building their homes, boats, and even the artificial islands where they live on with methods based almost exclusively on the totora. This way of living and production system has been maintained for more than 500 years. This review is about the main constructive techniques that have been used for traditional construction in totora and some of therecent researches that have been made on this subject. Experiments in architecture and industrial design objects made with totora have shown its

Low cost construction technologies and materials - case study Mozambuique

CSIR Research Space (South Africa)

Kuchena, JC

2009-09-01

Full Text Available Low cost or affordable construction technologies and materials are often touted as a panacea in meeting the ever growing demand for rapid housing delivery in developing economies. Mozambique as with most of the developing world, from both historical...

Video Games, Identity, and the Constellation of Information

Science.gov (United States)

Martin, Crystle

2012-01-01

This article explores the identity of youth in relation to the information sources they choose in the constellation of information of video games, using the massively multiplayer online game "World of Warcraft" as an example. From this study, several identities are recognized that are combinations of the participants skill and level in the game,…

RapidEye constellation relative radiometric accuracy measurement using lunar images

Science.gov (United States)

Steyn, Joe; Tyc, George; Beckett, Keith; Hashida, Yoshi

2009-09-01

The RapidEye constellation includes five identical satellites in Low Earth Orbit (LEO). Each satellite has a 5-band (blue, green, red, red-edge and near infrared (NIR)) multispectral imager at 6.5m GSD. A three-axes attitude control system allows pointing the imager of each satellite at the Moon during lunations. It is therefore possible to image the Moon from near identical viewing geometry within a span of 80 minutes with each one of the imagers. Comparing the radiometrically corrected images obtained from each band and each satellite allows a near instantaneous relative radiometric accuracy measurement and determination of relative gain changes between the five imagers. A more traditional terrestrial vicarious radiometric calibration program has also been completed by MDA on RapidEye. The two components of this program provide for spatial radiometric calibration ensuring that detector-to-detector response remains flat, while a temporal radiometric calibration approach has accumulated images of specific dry dessert calibration sites. These images are used to measure the constellation relative radiometric response and make on-ground gain and offset adjustments in order to maintain the relative accuracy of the constellation within +/-2.5%. A quantitative comparison between the gain changes measured by the lunar method and the terrestrial temporal radiometric calibration method is performed and will be presented.

Prevention of radioactive gas seeping into buildings through constructive materials

International Nuclear Information System (INIS)

Khaydarov, R.A.; Gapurova, O.U.; Khaydarov, R.R.

2004-01-01

Full text: One of possible method of realization of the terrorist acts is using gases and liquids, which easily permeate through the constructive materials of walls, floor, ceiling, roof, etc. into buildings by the capillary action of the pores. Toxic volatile organic compounds, organic and inorganic gases, radioactive elements, especially, which emits alpha particles can be used as the dangerous substances. Increased ventilation may help in removing the gases, but can actually increase the gases level by increasing the suction through the pores of concrete. If the gases and liquids are soluble in water and are easily volatilized from it, they can also get by groundwater up to underground structures and penetrate inside through opening and pores in concrete or pushed by hydrostatic pressure. The purpose of this work is creating a method to reduce concentration of toxic and radioactive gases in homes, buildings, underground buildings, tunnels, hangars, garages, bomb shelters, etc. The most effective method to prevent penetration of radionuclides into premises of buildings and underground structures through walls, roofs, floors is using special chemicals, which seal micropores inside the construction materials against gases. Worked out chemicals which consist of blend of polymeric compounds are described in the paper. Radioactive gases permeability in constructive materials after treatment by chemicals was studied. Influence of types of cement, sand and gypsum, preliminary treatment by different chemicals, different types of polymeric compounds, time between treatments, moisture of materials, time between preparation of chemicals and treatment of materials (aging of chemicals), time between treatment of concrete and testing (aging of treated concrete) were examined. Experiments have shown that our method allows reducing the coefficient of gas permeability 200 - 400 times

Analysis and design of Cubesat constellation for the Mediterranean south costal monitoring against illegal immigration

Science.gov (United States)

Lazreg, Nissen; Ben Bahri, Omar; Besbes, Kamel

2018-02-01

Costal monitoring is focused on fast response to illegal immigration and illegal ship traffic. Especially, the illegal ship traffic has been present in media since April 2015, as the number of reported deaths of immigrants crossing the Mediterranean significantly increased. Satellite images provide a possibility to at least partially control both types of events. This paper defines the principal criteria to select the best satellite constellation architecture for maritime and coastal monitoring, filling the gaps of imagery techniques in term of real-time control. The primary purpose of a constellation is to obtain global measurement improving the temporal resolution. The small size and low-cost are the main factors, which make CubeSats ideal for use in constellations. We propose a constellation of 9 Cubesats distributed evenly in 3 different planes. This reduces the revisit time enhancing the coverage duration. In addition, it also allows observing fire, damage on building and similar disasters. In this analysis, the performance criteria were reported such as the revisit time, the vision duration and the area coverage.

Constellation Shaping for Fiber-optic Channels with QAM and High Spectral Efficiency

DEFF Research Database (Denmark)

Yankov, Metodi Plamenov; Zibar, Darko; Larsen, Knud J.

2014-01-01

In this letter the fiber-optic communication channel with Quadrature Amplitude Modulation (QAM) input constella- tion is treated. Using probabilistic shaping, we show that high order QAM constellations can achieve and slightly exceed the lower bound on the channel capacity, set by ring constellat......In this letter the fiber-optic communication channel with Quadrature Amplitude Modulation (QAM) input constella- tion is treated. Using probabilistic shaping, we show that high order QAM constellations can achieve and slightly exceed the lower bound on the channel capacity, set by ring...... constellations in [1]. We then propose a mapping function for turbo coded bit interleaved coded modulation based on optimization of the mu- tual information between the channel input and output. Using this mapping, spectral efficiency as high as 6.5 bits/s/Hz/polarization is achieved on a simulated single...... channel long-haul fiber-optical link excluding the pilot overhead, used for synchronization, and taking into account frequency and phase mismatch impairments, as well as laser phase noise and analog-to-digital conversion quantization impairments. The simulations suggest that major improvements can...

Beyond the material grave: Life Cycle Impact Assessment of leaching from secondary materials in road and earth constructions.

Science.gov (United States)

Schwab, Oliver; Bayer, Peter; Juraske, Ronnie; Verones, Francesca; Hellweg, Stefanie

2014-10-01

In industrialized countries, large amounts of mineral wastes are produced. They are re-used in various ways, particularly in road and earth constructions, substituting primary resources such as gravel. However, they may also contain pollutants, such as heavy metals, which may be leached to the groundwater. The toxic impacts of these emissions are so far often neglected within Life Cycle Assessments (LCA) of products or waste treatment services and thus, potentially large environmental impacts are currently missed. This study aims at closing this gap by assessing the ecotoxic impacts of heavy metal leaching from industrial mineral wastes in road and earth constructions. The flows of metals such as Sb, As, Pb, Cd, Cr, Cu, Mo, Ni, V and Zn originating from three typical constructions to the environment are quantified, their fate in the environment is assessed and potential ecotoxic effects evaluated. For our reference country, Germany, the industrial wastes that are applied as Granular Secondary Construction Material (GSCM) carry more than 45,000 t of diverse heavy metals per year. Depending on the material quality and construction type applied, up to 150 t of heavy metals may leach to the environment within the first 100 years after construction. Heavy metal retardation in subsoil can potentially reduce the fate to groundwater by up to 100%. One major challenge of integrating leaching from constructions into macro-scale LCA frameworks is the high variability in micro-scale technical and geographical factors, such as material qualities, construction types and soil types. In our work, we consider a broad range of parameter values in the modeling of leaching and fate. This allows distinguishing between the impacts of various road constructions, as well as sites with different soil properties. The findings of this study promote the quantitative consideration of environmental impacts of long-term leaching in Life Cycle Assessment, complementing site-specific risk

The Use Potential of Traditional Building Materials for the Realization of Structures by Modern Methods of Construction

Directory of Open Access Journals (Sweden)

Spišáková Marcela

2015-11-01

Full Text Available The sustainable building has taken off in recent years with many investors looking for new and different methods of construction. The traditional building materials can be made out of natural materials, while others can help to lower energy costs of the occupant once built. Regardless of what the goal of the investor is, traditional building materials and their use is on the rise. The submitted paper provides an overview of natural building materials and possible modern building systems using these construction materials. Based on the questionnaire survey is defined the use potential of traditional building materials for the realization of the construction by methods of modern constructions and then are determined the drivers and barriers of traditional materials through using modern methods of construction. Considering the analysis of the achieved results, we can identify the gaps in the construction market in Slovakia and also to assess the perception of potential investors in the field of traditional building materials use, which is the purpose of submitted paper.

Decontamination of radionuclides on construction materials

International Nuclear Information System (INIS)

Samuleev, P.V.; Andrews, W.S.; Creber, K.A.M.; Velicogna, D.

2013-01-01

A wide variety of materials can become contaminated by radionuclides, either from a terrorist attack or an industrial or nuclear accident. The final disposition of these materials depends, in large part, on the effectiveness of decontamination measures. This study reports on investigations into the decontamination of a selection of building materials. The aim has been to find an effective, easy-to-use and inexpensive decontamination system for radionuclides of cesium and cobalt, considering both the chemical and physical nature of these potential contaminants. The basic method investigated was surface washing, due to its ease and simplicity. In the present study, a basic decontamination formulation was modified by adding isotope-specific sequestering agents, to enhance the removal of cesium(I) and cobalt(II) from such construction materials as concrete, marble, aluminum and painted steel. Spiking solutions contained 134 Cs or 60 Co, which were prepared by neutron activation in the SLOWPOKE-2 nuclear reactor facility at the Royal Military College of Canada. Gamma spectroscopy was used to determine the decontamination efficiency. The results showed that the addition of sequestering agents generally improved the radiological decontamination. Although the washing of both cesium and cobalt from non-porous materials, such as aluminum and painted steel, achieved a 90-95 % removal, the decontamination of concrete and marble was more challenging, due to the porous nature of the materials. Nevertheless, the removal efficiency from 6-year-old concrete increased from 10 % to approximately 50 % for cobalt(II), and from 18 to 55 % for cesium(I), with the use of isotope binding agents, as opposed to a simple water wash. (author)

AN ASSESSMENT OF FACTORS AFFECTING MATERIAL STOCK CONTROL PRACTICE ON SELECTED CONSTRUCTION SITES IN NIGERIA

OpenAIRE

Adafin, Johnson Kayode; Ayodele, Elijah Olusegun; Daramola, Olufemi

2011-01-01

This research examines the stock control methods utilized by construction firms on construction sites with a view to assessing the factors affecting material stock control practice by construction firms as well as determining the impact of factors affecting material stock control on building project performance. Data were collected with the aid of well-structured questionnaire administered on a number of construction professionals and technicians in some randomly selected building constructio...

Low-complexity blind equalization for OFDM systems with general constellations

KAUST Repository

Al-Naffouri, Tareq Y.; Dahman, Ala A.; Sohail, Muhammad Sadiq; Xu, Weiyu; Hassibi, Babak

2012-01-01

This paper proposes a low-complexity algorithm for blind equalization of data in orthogonal frequency division multiplexing (OFDM)-based wireless systems with general constellations. The proposed algorithm is able to recover the transmitted data

Quality control of three main materials for civil construction of nuclear power plant

International Nuclear Information System (INIS)

Wang Feng

2011-01-01

The construction and operation of nuclear power plant is a systematic engineering. To ensure quality and safety of nuclear power plants, each work from design to operation can have certain impact on the quality and safety of the project. The quality of each related work shall be controlled. Starting from the quality control over raw materials for the civil construction of nuclear power plant, this article mainly analyzes how to control the quality and manage the three main materials of steel, concrete and modular parts in the civil construction. (author)

Construction and commissioning of workrooms for handling of unsealed radioactive materials

International Nuclear Information System (INIS)

Weinhold, G.; Jost, E.; Koenig, W.

1976-03-01

The requirements prescribed for planning, design and construction of type II and III workrooms for handling of unsealed sources are outlined. The 'Guide Concerning Construction and Equipment of Rooms for Handling of Radioactive Materials' is explained and supplemented in part. Furthermore, problems of radiation protection organization and measuring techniques are discussed. (author)

Measurements of the radioactivity of power plant by-products processed into construction materials

International Nuclear Information System (INIS)

Marcinkowski, S.A.; Dudelewski, H.A.

1992-01-01

The subject of the recycling of residual products comprising, inter alia, fly ash and slags accuring from the combustion of black and brown coal in modern coal dust boilers in the power industry has been topical for a number of years. Numerous discussions and articles in technical periodicals and the daily press have revolved around the problem of the radioactivity of construction materials or construction elements obtained from fly ash or slags of power plant. In Poland, this was a forbidden subject until the publication in 1980 by the Warsaw institute of construction technology of standard no. 234 entitled: 'Recommendations for establishing the natural radioactivity of products processed into construction materials'. (orig.) [de

Aeolian sands as material to construct low-volume roads

CSIR Research Space (South Africa)

Paige-Green, P

2011-07-01

Full Text Available Aeolian sands are widespread in many semi-arid to arid areas of the world and often provide the only economic source of construction materials for low volume roads. Experience in southern Africa over a number of decades has shown that provided...

Center for Coal-Derived Low Energy Materials for Sustainable Construction

Energy Technology Data Exchange (ETDEWEB)

Jewell, Robert; Robl, Tom; Rathbone, Robert

2012-06-30

The overarching goal of this project was to create a sustained center to support the continued development of new products and industries that manufacture construction materials from coal combustion by-products or CCB’s (e.g., cements, grouts, wallboard, masonry block, fillers, roofing materials, etc). Specific objectives includes the development of a research kiln and associated system and the formulation and production of high performance low-energy, low-CO2 emitting calcium sulfoaluminate (CAS) cement that utilize coal combustion byproducts as raw materials.

Options and recommendations for a web database of material and construction inspection.

Science.gov (United States)

2015-02-01

The Illinois Department of Transportation (IDOT) has been using software developed in-house for their : materials management and construction project management needs. The primary packages under : review MISTIC (Materials Management) and ICORS (Const...

Vegetable Fibers for Composite Materials In Constructive Sector

Science.gov (United States)

Giglio, Francesca; Savoja, Giulia

2017-08-01

The aim of the research is to study and to test bio-mixture for laminas to use in construction field components. Composite materials are becoming more common in different sectors, but their embodied energy is an environmental problem. For this, in recent years, the researchers investigate new mixtures for composites, in particular with vegetable fibers and bio-based epoxy resin. The research carried out different laboratory tests for material and mechanical characterization, starting from the analysis of vegetable fibers, and arriving to test different kind of laminas with sundry fabrics and bio-based epoxy resin. In the most general organization of the theme, the research has the overall objective to contribute to reduce composites environmental impacts, with the promotion of local production chains about innovative materials from renewable and sustainable sources.

Tabitha's One Teacher Rural School: Insights into the Arts through the Use of a Story Constellation

Science.gov (United States)

Garvis, Susanne

2011-01-01

This paper presents a story constellation about a beginning teacher (who is also the principal) located in a one-teacher school in an isolated community in Queensland, Australia. The constellation documents the teacher's self-efficacy for teaching the arts (music, dance, drama, visual arts and media). Tabitha, the participant, shares insights…

29 CFR 779.335 - Sales of building materials for residential or farm building construction.

Science.gov (United States)

2010-07-01

... materials for residential or farm building construction. Section 3(n) of the Act, as amended, excludes from... 29 Labor 3 2010-07-01 2010-07-01 false Sales of building materials for residential or farm building construction. 779.335 Section 779.335 Labor Regulations Relating to Labor (Continued) WAGE AND...

Materials Design and System Construction for Conventional and New-Concept Supercapacitors.

Science.gov (United States)

Wu, Zhong; Li, Lin; Yan, Jun-Min; Zhang, Xin-Bo

2017-06-01

With the development of renewable energy and electrified transportation, electrochemical energy storage will be more urgent in the future. Supercapacitors have received extensive attention due to their high power density, fast charge and discharge rates, and long-term cycling stability. During past five years, supercapacitors have been boomed benefited from the development of nanostructured materials synthesis and the promoted innovation of devices construction. In this review, we have summarized the current state-of-the-art development on the fabrication of high-performance supercapacitors. From the electrode material perspective, a variety of materials have been explored for advanced electrode materials with smart material-design strategies such as carbonaceous materials, metal compounds and conducting polymers. Proper nanostructures are engineered to provide sufficient electroactive sites and enhance the kinetics of ion and electron transport. Besides, new-concept supercapacitors have been developed for practical application. Microsupercapacitors and fiber supercapacitors have been explored for portable and compact electronic devices. Subsequently, we have introduced Li-/Na-ion supercapacitors composed of battery-type electrodes and capacitor-type electrode. Integrated energy devices are also explored by incorporating supercapacitors with energy conversion systems for sustainable energy storage. In brief, this review provides a comprehensive summary of recent progress on electrode materials design and burgeoning devices constructions for high-performance supercapacitors.

Improved Suction Technique for the Characterization of Construction Materials

DEFF Research Database (Denmark)

Thygesen, Lisbeth Garbrecht; Hansen, Kurt Kielsgaard

2007-01-01

The suction technique is a method from soil science that is used for the study of moisture storage capacity in porous construction materials at high relative humidity levels (above approximately 93%). The samples to be studied are placed in a pressurized container (an extractor) on a water...

The application of waste fly ash and construction-waste in cement filling material in goaf

Science.gov (United States)

Chen, W. X.; Xiao, F. K.; Guan, X. H.; Cheng, Y.; Shi, X. P.; Liu, S. M.; Wang, W. W.

2018-01-01

As the process of urbanization accelerated, resulting in a large number of abandoned fly ash and construction waste, which have occupied the farmland and polluted the environment. In this paper, a large number of construction waste and abandoned fly ash are mixed into the filling material in goaf, the best formula of the filling material which containing a large amount of abandoned fly ash and construction waste is obtained, and the performance of the filling material is analyzed. The experimental results show that the cost of filling material is very low while the performance is very good, which have a good prospect in goaf.

Radiation damage of the construction materials, Phase I, Part I- Radiation damage of the construction steels

International Nuclear Information System (INIS)

Lazarevic, Dj.

1962-10-01

The objective of this task was testing the mechanical properties of stainless steels having different grain size. Being an important material used mainly for reactor vessel construction stainless steel will be exposed to neutron flux in the RA reactor for testing

CubeSat constellations for disaster management in remote areas

Science.gov (United States)

Santilli, Giancarlo; Vendittozzi, Cristian; Cappelletti, Chantal; Battistini, Simone; Gessini, Paolo

2018-04-01

In recent years, CubeSats have considerably extended their range of possible applications, from a low cost means to train students and young researchers in space related activities up to possible complementary solutions to larger missions. Increasingly popular, whereas CubeSats are still not a solution for all types of missions, they offer the possibility of performing ambitious scientific experiments. Especially worth considering is the possibility of performing Distributed Space Missions, in which CubeSat systems can be used to increase observation sampling rates and resolutions, as well as to perform tasks that a single satellite is unable to handle. The cost of access to space for traditional Earth Observation (EO) missions is still quite high. Efficient architecture design would allow reducing mission costs by employing CubeSat systems, while maintaining a level of performance that, for some applications, could be close to that provided by larger platforms, and decreasing the time needed to design and deploy a fully functional constellation. For these reasons many countries, including developing nations, agencies and organizations are looking to CubeSat platforms to access space cheaply with, potentially, tens of remote sensing satellites. During disaster management, real-time, fast and continuous information broadcast is a fundamental requirement. In this sense, a constellation of small satellites can considerably decrease the revisit time (defined as the time elapsed between two consecutive observations of the same point on Earth by a satellite) over remote areas, by increasing the number of spacecraft properly distributed in orbit. This allows collecting as much data as possible for the use by Disaster Management Centers. This paper describes the characteristics of a constellation of CubeSats built to enable access over the most remote regions of Brazil, supporting an integrated system for mitigating environmental disasters in an attempt to prevent the

Radon diffusion through sandy construction materials: effect of temperature and grain size

International Nuclear Information System (INIS)

Narula, A.K.; Goyal, S.K.; Jain, Ravinder; Kant, Krishan; Yadav, Mani Kant; Chauhan, R.P.; Chakarvarti, S.K.

2013-01-01

Radon appears mainly by diffusion process from the point of origin, say, under ground soil and building materials used in construction of house following alpha decay of radium. The radon diffusion through different building construction materials can be compared by calculating radon diffusion coefficient for them. In the present work, we studied the effect of temperature and grain size on radon diffusion of coarse sand as construction material. The coarse sand was collected from Yamuna river bed, originated from Himalayas. For this study, a steel pipe of diameter 10 cm and length 30 cm., divided into four sectors of equal size, was filled in different sectors with different grain sized (800, 600 and 425 μm) sand as building construction material. A number LR-115 type-II particle track detectors were placed with inter-detector distance of 10 cm in the sectorial compartments. The bottom end of steel pipe assembly was fixed with a radon chamber containing radon source with upper end sealed with a cap. The whole arrangement was then placed into a sand-clay pipe wrapped around by a controlled heating filament, resulting into temperature variations from 25℃ to 60℃. After 100 days interval, the detectors were retrieved processed, and the α - tracks counted for the calculation of radon concentration. It is observed that the radon diffusion coefficient increases with the increase in temperature and decreases with decrease in grain size of the coarse sand. (author)

Application of Nanotechnology-Based Thermal Insulation Materials in Building Construction

Directory of Open Access Journals (Sweden)

Bozsaky David

2016-03-01

Full Text Available Nanotechnology-based materials have previously been used by space research, pharmaceuticals and electronics, but in the last decade several nanotechnology-based thermal insulation materials have appeared in building industry. Nowadays they only feature in a narrow range of practice, but they offer many potential applications. These options are unknown to most architects, who may simply be afraid of these materials owing to the incomplete and often contradictory special literature. Therefore, they are distrustful and prefer to apply the usual and conventional technologies. This article is intended to provide basic information about nanotechnology-based thermal insulation materials for designers. It describes their most important material properties, functional principles, applications, and potential usage options in building construction.

Leo Satellite Communication through a LEO Constellation using TCP/IP Over ATM

Science.gov (United States)

Foore, Lawrence R.; Konangi, Vijay K.; Wallett, Thomas M.

1999-01-01

The simulated performance characteristics for communication between a terrestrial client and a Low Earth Orbit (LEO) satellite server are presented. The client and server nodes consist of a Transmission Control Protocol /Internet Protocol (TCP/IP) over ATM configuration. The ATM cells from the client or the server are transmitted to a gateway, packaged with some header information and transferred to a commercial LEO satellite constellation. These cells are then routed through the constellation to a gateway on the globe that allows the client/server communication to take place. Unspecified Bit Rate (UBR) is specified as the quality of service (QoS). Various data rates are considered.

Materials Design and System Construction for Conventional and New‐Concept Supercapacitors

Science.gov (United States)

Wu, Zhong; Li, Lin

2017-01-01

With the development of renewable energy and electrified transportation, electrochemical energy storage will be more urgent in the future. Supercapacitors have received extensive attention due to their high power density, fast charge and discharge rates, and long‐term cycling stability. During past five years, supercapacitors have been boomed benefited from the development of nanostructured materials synthesis and the promoted innovation of devices construction. In this review, we have summarized the current state‐of‐the‐art development on the fabrication of high‐performance supercapacitors. From the electrode material perspective, a variety of materials have been explored for advanced electrode materials with smart material‐design strategies such as carbonaceous materials, metal compounds and conducting polymers. Proper nanostructures are engineered to provide sufficient electroactive sites and enhance the kinetics of ion and electron transport. Besides, new‐concept supercapacitors have been developed for practical application. Microsupercapacitors and fiber supercapacitors have been explored for portable and compact electronic devices. Subsequently, we have introduced Li‐/Na‐ion supercapacitors composed of battery‐type electrodes and capacitor‐type electrode. Integrated energy devices are also explored by incorporating supercapacitors with energy conversion systems for sustainable energy storage. In brief, this review provides a comprehensive summary of recent progress on electrode materials design and burgeoning devices constructions for high‐performance supercapacitors. PMID:28638780

WET-WEATHER POLLUTION PREVENTION THROUGH MATERIALS SUBSTITUTION AS PART OF INDUSTRIAL CONSTRUCTION

Science.gov (United States)

A literature review of urban stormwater runoff and building/construction materials has shown that many materials such as galvanized metal, concrete, asphalt, and wood products, have the potential to release pollutants into urban stormwater runoff and snowmelt. However, much of th...

Evaluating the Readability of Radio Frequency Identification for Construction Materials

Directory of Open Access Journals (Sweden)

Younghan Jung

2017-01-01

Full Text Available Radio Frequency Identification (RFID, which was originally introduced to improve material handling and speed production as part of supply chain management, has become a globally accepted technology that is now applied on many construction sites to facilitate real-time information visibility and traceability. This paper describes a senior undergraduate project for a Construction Management (CM program that was specifically designed to give the students a greater insight into technical research in the CM area. The students were asked to determine whether it would be possible to utilize an RFID system capable of tracking tagged equipment, personnel and materials across an entire construction site. This project required them to set up an experimental program, execute a series of experiments, analyze the results and summarize them in a report. The readability test was performed using an active Ultra-High frequency (UHF, 433.92 MHz RFID system with various construction materials, including metal, concrete, wood, plastic, and aluminum. The readability distance distances are measured for each of the six scenarios. The distance at which a tag was readable with no obstructions was found to be an average of 133.9m based on three measurements, with a standard deviation of 3.9m. This result confirms the manufacturer’s claimed distance of 137.2m. The RFID tag embedded under 50.8mm of concrete was readable for an average distance of only 12.2m, the shortest readable distance of any of the scenarios tested. At the end of the semester, faculty advisors held an open discussion session to gather feedback and elicit the students’ reflections on their research experiences, revealing that the students’ overall impressions of their undergraduate research had positively affected their postgraduate education plans.

Family constellation as a treatment for overcoming the consequences of violence on victims

Directory of Open Access Journals (Sweden)

Hrnčić Jasna

2017-01-01

Full Text Available The subject of this paper is the implementation of family constellations by Bert Hellinger in work with clients with special emphasis on victims of physical and sexual violence. Although extremely popular in Europe and the world it has not been presented in Serbian scientific literature. As the approach has been developed in Germany as an answer to the situation where a significant part of population was a victim or perpetrator of violence during the Second World War causing suffering not only to them, but also to their offsprings, it offers a special contribution to the work with victims of violence. The aims of the paper are the presentation and analysis of the implementation of family constellations by Bert Hellinger and their effects generally in work with clients as well as with victims of physical and sexual violence. The technique of family constellations based on systemic and phenomenological approach is presented and discussed. Work is in the group, where participants form the circle and person who seeks problem resolution invites representatives - persons who are crucial for problem solution previously agreed with constellation facilitator - constellator. The constellator communicate with the representatives, encouraging them to express feelings, sensations and movement that will facilitate progress towards finding the optimal solution. The basic theoretical concepts are also analysed, including two types of conscience (individual and family, three basic principles of orders of love (principle of equal right to belong, principle of balance between giving and taking and principle of order and three levels of the soul (individual, family and great soul. The approach to overcoming consequences of violence on victims of physical violence and incest through symbolic interconnecting with the perpetrator is analysed. When it is applied to violence the victim has an opportunity to get a more comprehensive understanding and to experience an

Modern diaper performance: construction, materials, and safety review.

Science.gov (United States)

Dey, Swatee; Kenneally, Dianna; Odio, Mauricio; Hatzopoulos, Ioannis

2016-07-01

A review of the literature on diapers and diaper rash reveals that many clinicians are unfamiliar with modern diaper construction and materials as well as diaper safety testing methods. Typical modern diapers do not contain ingredients of concern such as latex and disperse dyes, but use ingredients such as spandex and pigments with a favorable safety profile. Today's disposable diaper is a high performance product whose carefully designed layers and liners provide optimal urine and feces absorption and an ever more clothing-like and comfortable fit. This is possible due to a variety of specialized polymer materials that provide optimal absorption of urine and feces, thereby minimizing skin exposure. © 2016 The International Society of Dermatology.

Global communication using a constellation of low earth meridian orbits

Science.gov (United States)

Oli, P. V. S.; Nagarajan, N.; Rayan, H. R.

1993-07-01

The concept of 'meridian orbits' is briefly reviewed. It is shown that, if a satellite in the meridian orbit makes an odd number of revolutions per day, then the satellite passes over the same set of meridians twice a day. Satellites in such orbits pass over the same portion of the sky twice a day and every day. This enables a user to adopt a programmed mode of tracking, thereby avoiding a computational facility for orbit prediction, look angle generation, and auto tracking. A constellation of 38 or more satellites placed in a 1200 km altitude circular orbit is favorable for global communications due to various factors. It is shown that appropriate phasing in right ascension of the ascending node and mean anomaly results in a constellation, wherein each satellite appears over the user's horizon one satellite after another. Visibility and coverage plots are provided to verify the continuous coverage.

Natural road construction materials of Southern Africa

CSIR Research Space (South Africa)

Weinert, HH

1980-01-01

Full Text Available respectively. p. 210. column 4: Insert Notre in rect311glc directly below heading Matrix. p. 240, paragraph 5, line 4: J 770 should read I 700. I ~I -~ r THE NATURAL ROAD CONSTRUCTION MATERIALS OF SOUTHERN AFRICA ACADEMICA I PRETORIA ICAPE TOWN ISBN... and the author acknowledges gratefully the valuable assistance and the trouble taken by the following persons: Southern African road authorities: Mr W. J. Biesenbach, Mr H. K. Geel, Mr C. L. Laubscher, Mr G. P. Marais, Mr R. L. Mitchell, Mr I. P. A. Smit, Mr C...

Properties of Residue from Olive Oil Extraction as a Raw Material for Sustainable Construction Materials. Part I: Physical Properties

Directory of Open Access Journals (Sweden)

Almudena Díaz-García

2017-01-01

Full Text Available Action on climate, the environment, and the efficient use of raw materials and resources are important challenges facing our society. Against this backdrop, the construction industry must adapt to new trends and environmentally sustainable construction systems, thus requiring lines of research aimed at keeping energy consumption in new buildings as low as possible. One of the main goals of this research is to efficiently contribute to reducing the amount of residue from olive oil extraction using a two-phase method. This can be achieved by producing alternative structural materials to be used in the construction industry by means of a circular economy. The technical feasibility of adding said residue to ceramic paste was proven by analyzing the changes produced in the physical properties of the paste, which were then compared to the properties of the reference materials manufactured with clay without residue. Results obtained show that the heating value of wet pomace can contribute to the thermal needs of the sintering process, contributing 30% of energy in pieces containing 3% of said material. Likewise, adding larger amounts of wet pomace to the clay body causes a significant decrease in bulk density values.

Properties of Residue from Olive Oil Extraction as a Raw Material for Sustainable Construction Materials. Part I: Physical Properties.

Science.gov (United States)

Díaz-García, Almudena; Martínez-García, Carmen; Cotes-Palomino, Teresa

2017-01-25

Action on climate, the environment, and the efficient use of raw materials and resources are important challenges facing our society. Against this backdrop, the construction industry must adapt to new trends and environmentally sustainable construction systems, thus requiring lines of research aimed at keeping energy consumption in new buildings as low as possible. One of the main goals of this research is to efficiently contribute to reducing the amount of residue from olive oil extraction using a two-phase method. This can be achieved by producing alternative structural materials to be used in the construction industry by means of a circular economy. The technical feasibility of adding said residue to ceramic paste was proven by analyzing the changes produced in the physical properties of the paste, which were then compared to the properties of the reference materials manufactured with clay without residue. Results obtained show that the heating value of wet pomace can contribute to the thermal needs of the sintering process, contributing 30% of energy in pieces containing 3% of said material. Likewise, adding larger amounts of wet pomace to the clay body causes a significant decrease in bulk density values.

Challenges of UK/Irish Contractors regarding Material Management and Logistics in Confined Site Construction

Directory of Open Access Journals (Sweden)

Spillane, John P

2011-12-01

Full Text Available The aim of this paper is to identify the various managerial issues encountered by UK/Irish contractors in the management of materials in confined urban construction sites. Through extensive literature review, detailed interviews, case studies, cognitive mapping, causal loop diagrams, questionnaire survey and documenting severity indices, a comprehensive insight into the materials management concerns within a confined construction site environment is envisaged and portrayed. The leading issues highlighted are: that contractors’ material spatial requirements exceed available space, it is difficult to coordinate the storage of materials in line with the programme, location of the site entrance makes delivery of materials particularly difficult, it is difficult to store materials on-site due to the lack of space, and difficult to coordinate the storage requirements of the various sub-contractors. With the continued development of confined urban centres and the increasing high cost of materials, any marginal savings made on-site would translate into significant monetary savings at project completion. Such savings would give developers a distinct competitive advantage in this challenging economic climate. As on-site management professionals successfully identify, acknowledge and counteract the numerous issues illustrated, the successful management of materials on a confined urban construction site becomes attainable.

Fiscal 2000 survey report. Survey and study of constellation satellites technology; 2000 nendo chosa hokokusho. Konsutereshon eisei gijutsu ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Demands for constellation satellites were surveyed and satellite systems were studied for extracting basic technical tasks relative to constellation satellite systems and for drafting space verification plans. For a constellation satellite system to accomplish its missions, two or more satellites have to be simultaneously navigated. It is assumed that its field of application will cover earth observation, information communication, risk management, disaster prevention, and the like. With such applications taken into consideration, surveys and studies were conducted about the need and marketability of constellation satellites, need of state-level involvement, and requests for missions to be imposed on a constellation system. For plural satellites to satisfy mission requests by coordinating with each other, it will be necessary to develop basic technologies, such as navigational guidance, communications control, system autonomous management, and operation on the ground. Functions and performance that a constellation satellite system are requested to have and basic technologies to be studied and developed were extracted, and space verification plans were drafted. (NEDO)

Value-Based Business-IT Alignment in Networked Constellations of Enterprises

NARCIS (Netherlands)

Gordijn, Jaap; van Eck, Pascal; Cox, K.; Dubois, E.; Pigneur, Y.; Bleistein, S.J.; Verner, J.; Davis, A.M.; Wieringa, Roelf J.

Business-ICT alignment is the problem of matching ICTservices with the requirements of the business. In businesses of any significant size, business-ICT alignment is a hard problem, which is currently not solved completely. With the advent of networked constellations of enterprises, the problem gets

Evaluation on construction quality of pit filler material of cavern type radioactive waste disposal facility

International Nuclear Information System (INIS)

Takechi, Shin-ichi; Yokozeki, Kosuke; Shimbo, Hiroshi; Terada, Kenji; Akiyama, Yoshihiro; Yada, Tsutomu; Tsuji, Yukikazu

2014-01-01

The pit filler material of the underground cavern-type radioactive waste disposal facility, which is poured directly around the radioactive waste packages where high temperature environment is assumed by their decay heat, is concerned to be adversely affected on the filling behavior and its hardened properties. There also are specific issues that required quality of construction must be achieved by unmanned construction with remote operation, because the pit filler construction shall be done under radiation environment. In this paper, the mix proportion of filler material is deliberated with filling experiments simulating high temperature environment, and also the effect of temperature on hardened properties are confirmed with high temperature curing test. Subsequently, the feasibility of unmanned construction method of filler material by pumping, and by movable bucket, are comparatively discussed through a real size demonstration. (author)

A Duration Prediction Using a Material-Based Progress Management Methodology for Construction Operation Plans

Directory of Open Access Journals (Sweden)

Yongho Ko

2017-04-01

Full Text Available Precise and accurate prediction models for duration and cost enable contractors to improve their decision making for effective resource management in terms of sustainability in construction. Previous studies have been limited to cost-based estimations, but this study focuses on a material-based progress management method. Cost-based estimations typically used in construction, such as the earned value method, rely on comparing the planned budget with the actual cost. However, accurately planning budgets requires analysis of many factors, such as the financial status of the sectors involved. Furthermore, there is a higher possibility of changes in the budget than in the total amount of material used during construction, which is deduced from the quantity take-off from drawings and specifications. Accordingly, this study proposes a material-based progress management methodology, which was developed using different predictive analysis models (regression, neural network, and auto-regressive moving average as well as datasets on material and labor, which can be extracted from daily work reports from contractors. A case study on actual datasets was conducted, and the results show that the proposed methodology can be efficiently used for progress management in construction.

Waste-efficient materials procurement for construction projects: A structural equation modelling of critical success factors.

Science.gov (United States)

Ajayi, Saheed O; Oyedele, Lukumon O

2018-05-01

Albeit the understanding that construction waste is caused by activities ranging from all stages of project delivery process, research efforts have been concentrated on design and construction stages, while the possibility of reducing waste through materials procurement process is widely neglected. This study aims at exploring and confirming strategies for achieving waste-efficient materials procurement in construction activities. The study employs sequential exploratory mixed method approach as its methodological framework, using focus group discussion, statistical analysis and structural equation modelling. The study suggests that for materials procurement to enhance waste minimisation in construction projects, the procurement process would be characterised by four features. These include suppliers' commitment to low waste measures, low waste purchase management, effective materials delivery management and waste-efficient Bill of Quantity, all of which have significant impacts on waste minimisation. This implies that commitment of materials suppliers to such measures as take back scheme and flexibility in supplying small materials quantity, among others, are expected of materials procurement. While low waste purchase management stipulates the need for such measures as reduced packaging and consideration of pre-assembled/pre-cut materials, efficient delivery management entails effective delivery and storage system as well as adequate protection of materials during the delivery process, among others. Waste-efficient specification and bill of quantity, on the other hand, requires accurate materials take-off and ordering of materials based on accurately prepared design documents and bill of quantity. Findings of this study could assist in understanding a set of measures that should be taken during materials procurement process, thereby corroborating waste management practices at other stages of project delivery process. Copyright © 2018. Published by Elsevier Ltd.

Toxic substances or dangerous presents in the construction materials

International Nuclear Information System (INIS)

Campos Alvarado, A.

2003-01-01

The purpose of this work of investigation is the elaboration of a guide who serves as support and consults in the referring thing to the subject of the security in the construction, specifically in and area of the use and handling of materials and dangerous substances; Considering the possible dangers to medium and long term that some of but the common construction equipments represent for the health. The obtained data is a bibliographical review, the visits to public institutions and international offices with representation in our country, as well as a work of field and study of the national market, among others. In addition it made an important consultation through network Internet reviewing many sites of with the purpose of obtaining the data but updated interest possible, as well as the consultation to professionals and workers with the area of the construction. (Author) [es

Challenges of UK/Irish Contractors regarding Material Management and Logistics in Confined Site Construction

OpenAIRE

Spillane, John P; Oyedele, Lukumon O; Von Meding, Jason; Konanahalli, Ashwini; Jaiyeoba, Babatunde E; Tijani, Iyabo K

2011-01-01

The aim of this paper is to identify the various managerial issues encountered by UK/Irish contractors in the management of materials in confined urban construction sites. Through extensive literature review, detailed interviews, case studies, cognitive mapping, causal loop diagrams, questionnaire survey and documenting severity indices, a comprehensive insight into the materials management concerns within a confined construction site environment is envisaged and portrayed. The leading issues...

USE OF MIRROR PATTERN CUTTING OF NETTING MATERIALS FOR CONSTRUCTION OF LAKE BEACH SEINES

Directory of Open Access Journals (Sweden)

A. Nazarov

2014-12-01

Full Text Available Purpose. Justification and calculation of a new methodological approach to the construction of a standard beach seine (502 / 302 х 3.75 with the use of the properties of mirror netting ensuring the saving of the netting material, reduction of weight, price and drag resistance. Methodology. The carp age group selectivity of the constructed seine was assessed within fish fauna monitoring based on the catch analysis of monitoring gill nets with mesh sizes of 30-130 mm according to generally accepted methods [9, 10]. Calculation of netting materials and ropes was carried out according to generally accepted methods [12-14]. Seine resistance was calculated according to N. T. Senin formula for different netting materials and the angles of the movement of different seine parts in water [2]. The gear reliability and data processing were carried out according to standard methods [11, 14, 15]. Findings. A variant of the construction of the maximum lightweight beach lake seines made of mirror pattern netting taking into account the properties of the mirror pattern netting material, reduction of weight, price and drag resistance has been proposed. The provided recalculation of the properties of a serial seine made of rhombic mesh for the mirror netting seine taking into account netting properties allowed: 1 reducing the seine drag resistance value by 1,4 times; 2 reducing the weight of netting materials by 16.3% compared to the prototype; 3 increasing the seine selectivity when fishing older age groups of carp in non-drainable ponds. Originality. We presented the method of the calculation and construction of lake beach seines made of mirror netting, analyzed the technological stages of the construction of mirror netting, determined main qualitative and technological parameters, which had effect on the conditions of the construction and reliability of such fishing gears. A new method of the use of an insert of the combined netting material cutting ensuring

Environmentally Sustainable Construction Products and Materials – Assessment of release

DEFF Research Database (Denmark)

Wahlström, Margareta; Laine-Yliijoki, Jutta; Järnström, helena

The construction sector consumes yearly about half of all natural resourcesextracted in Europe and their transformation into building products has huge energy demands. Therefore the focus of today’s environmental policy is on the building end-of-life scenarios and material efficiency. Here waste...... hardly any construction product is designed keeping recycling/reuse in mind, the “Design for theEnvironment” -concept is one of the key steps towards increased recycling and reuse and thereby towards minimal environmental impacts. This project has been carried out by VTT with cooperation with the Danish...

Microbial biotechnology approaches to mitigating the deterioration of construction and heritage materials.

Science.gov (United States)

Junier, Pilar; Joseph, Edith

2017-09-01

Microorganisms are the main engines of elemental cycling in this planet and therefore have a profound impact on both organic and mineral substrates. As such, past and present human-made structures and cultural heritage can be negatively affected by microbial activity. Processes such as bioweathering (rocks and minerals), biodeterioration (organic substrates) or biocorrosion (metals) participate to the degradation or structural damage of construction and heritage materials. This structural damage can cause major economic losses (e.g. replacement of cast-iron pipes in water distribution networks), and in the case of heritage materials, the entire loss of invaluable objects or monuments. Even though one can regard the influence of microbial activity on construction and heritage materials as negative, remarkably, the same metabolic pathways involved in degradation can be exploited to increase the stability of these materials. © 2017 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

Exploring Database Improvements for GPM Constellation Precipitation Retrievals

Science.gov (United States)

Ringerud, S.; Kidd, C.; Skofronick Jackson, G.

2017-12-01

The Global Precipitation Measurement Mission (GPM) offers an unprecedented opportunity for understanding and mapping of liquid and frozen precipitation on a global scale. GPM mission development of physically based retrieval algorithms, for application consistently across the constellation radiometers, relies on combined active-passive retrievals from the GPM core satellite as a transfer standard. Radiative transfer modeling is then utilized to compute a priori databases at the frequency and footprint geometry of each individual radiometer. The Goddard Profiling Algorithm (GPROF) performs constellation retrievals across the GPM databases in a Bayesian framework, constraining searches using model data on a pixel-by-pixel basis. This work explores how the retrieval might be enhanced with additional information available within the brightness temperature observations themselves. In order to better exploit available information content, model water vapor is replaced with retrieved water vapor. Rather than treating each footprint as a 1D profile alone in space, information regarding Tb variability in the horizontal is added as well as variability in the time dimension. This additional information is tested and evaluated for retrieval improvement in the context of the Bayesian retrieval scheme. Retrieval differences are presented as a function of precipitation and surface type for evaluation of where the added information proves most effective.

Research on constellation refueling based on formation flying

Science.gov (United States)

Bo, Xu; Feng, Quansheng

2011-06-01

A new scheme for refueling satellite constellation is proposed in this paper. Compared with the traditional research, where the satellite refueling is implemented through spacecraft rendezvous and docking, the new pattern studied here is based on formation flying, and it is more feasible, safer and more reliable. On the grounds of the proposed pattern, two refueling strategies are studied. The first is called single supplier refueling (SSR) based on formation flying. In this scenario, one fuel-sufficient satellite called a supplier, departs from its parking orbit, and after a series of orbit maneuvers, arrives at the target constellation that consists of multiple fuel-deficient satellites called workers. It then transfers equal fuel to each worker within the prescribed mission time. The second strategy is called double suppliers refueling (DSR) based on formation flying. This time two suppliers take charge of refueling half of the workers respectively in the same way as SSR. Using a genetic algorithm, the orbit of a supplier with a minimum consumption of fuel can be obtained once the mission time is fixed. Simulation results indicate that DSR is superior to SSR and that this dominance will be more distinct as the number of workers increases and the mission time decreases.

Fluidized bed combustion bottom ash: A better and alternative geo-material resource for construction.

Science.gov (United States)

Mandal, A K; Paramkusam, Bala Ramudu; Sinha, O P

2018-04-01

Though the majority of research on fly ash has proved its worth as a construction material, the utility of bottom ash is yet questionable due to its generation during the pulverized combustion process. The bottom ash produced during the fluidized bed combustion (FBC) process is attracting more attention due to the novelty of coal combustion technology. But, to establish its suitability as construction material, it is necessary to characterize it thoroughly with respect to the geotechnical as well as mineralogical points of view. For fulfilling these objectives, the present study mainly aims at characterizing the FBC bottom ash and its comparison with pulverized coal combustion (PCC) bottom ash, collected from the same origin of coal. Suitability of FBC bottom ash as a dike filter material in contrast to PCC bottom ash in replacing traditional filter material such as sand was also studied. The suitability criteria for utilization of both bottom ash and river sand as filter material on pond ash as a base material were evaluated, and both river sand and FBC bottom ash were found to be satisfactory. The study shows that FBC bottom ash is a better geo-material than PCC bottom ash, and it could be highly recommended as an alternative suitable filter material for constructing ash dikes in place of conventional sand.

Construction raw materials policy and supply practices in Northwestern Europe

NARCIS (Netherlands)

Meulen, M.J. van der; Koopmans, T.P.F.; Pietersen, H.S.

2003-01-01

The present contribution is an inventory of the construction raw materials policy and supply practices in The Netherlands, Belgium, North Rhine-Westphalia, Lower Saxony, Great Britain, Norway and Denmark. The work has been commissioned by the Dutch government in order to benchmark its domestic

A satellite constellation optimization for a regional GNSS remote sensing mission

Science.gov (United States)

Gavili Kilaneh, Narin; Mashhadi Hossainali, Masoud

2017-04-01

Due to the recent advances in the Global Navigation Satellite System Remote sensing (GNSS¬R) applications, optimization of a satellite orbit to investigate the Earth's properties seems significant. The comparison of the GNSS direct and reflected signals received by a Low Earth Orbit (LEO) satellite introduces a new technique to remotely sense the Earth. Several GNSS¬R missions including Cyclone Global Navigation Satellite System (CYGNSS) have been proposed for different applications such as the ocean wind speed and height monitoring. The geometric optimization of the satellite orbit before starting the mission is a key step for every space mission. Since satellite constellation design varies depending on the application, we have focused on the required geometric criteria for oceanography applications in a specified region. Here, the total number of specular points, their spatial distribution and the accuracy of their position are assumed to be sufficient for oceanography applications. Gleason's method is used to determine the position of specular points. We considered the 2-D lattice and 3-D lattice theory of flower constellation to survey whether a circular orbit or an elliptical one is suitable to improve the solution. Genetic algorithm is implemented to solve the problem. To check the visibility condition between the LEO and GPS satellites, the satellite initial state is propagated by a variable step size numerical integration method. Constellation orbit parameters achieved by optimization provide a better resolution and precession for the specular points in the study area of this research.

Oriented strand board: new material for building construction

International Nuclear Information System (INIS)

Paridah Md Tahir; Ong, L.L.

2001-01-01

The paper will attempt to show the suitability and competitiveness of oriented strand board (OSB) in building construction. One important factor underlining the success of this product is the availability of the wood raw material. Plantation timbers such as rubberwood, paraserianthes falcataria, acacia crassicarpa, A. auriculiformis and A. mangium have been identified as the major source of this industry. We will focus on the domestic market as well as export market especially on the Asia Pacific region

Ground test of satellite constellation based quantum communication

OpenAIRE

Liao, Sheng-Kai; Yong, Hai-Lin; Liu, Chang; Shentu, Guo-Liang; Li, Dong-Dong; Lin, Jin; Dai, Hui; Zhao, Shuang-Qiang; Li, Bo; Guan, Jian-Yu; Chen, Wei; Gong, Yun-Hong; Li, Yang; Lin, Ze-Hong; Pan, Ge-Sheng

2016-01-01

Satellite based quantum communication has been proven as a feasible way to achieve global scale quantum communication network. Very recently, a low-Earth-orbit (LEO) satellite has been launched for this purpose. However, with a single satellite, it takes an inefficient 3-day period to provide the worldwide connectivity. On the other hand, similar to how the Iridium system functions in classic communication, satellite constellation (SC) composed of many quantum satellites, could provide global...

Attribute and topology based change detection in a constellation of previously detected objects

Science.gov (United States)

Paglieroni, David W.; Beer, Reginald N.

2016-01-19

A system that applies attribute and topology based change detection to networks of objects that were detected on previous scans of a structure, roadway, or area of interest. The attributes capture properties or characteristics of the previously detected objects, such as location, time of detection, size, elongation, orientation, etc. The topology of the network of previously detected objects is maintained in a constellation database that stores attributes of previously detected objects and implicitly captures the geometrical structure of the network. A change detection system detects change by comparing the attributes and topology of new objects detected on the latest scan to the constellation database of previously detected objects.

BAVP: Blockchain-Based Access Verification Protocol in LEO Constellation Using IBE Keys

Directory of Open Access Journals (Sweden)

Songjie Wei

2018-01-01

Full Text Available LEO constellation has received intensive research attention in the field of satellite communication. The existing centralized authentication protocols traditionally used for MEO/GEO satellite networks cannot accommodate LEO satellites with frequent user connection switching. This paper proposes a fast and efficient access verification protocol named BAVP by combining identity-based encryption and blockchain technology. Two different key management schemes with IBE and blockchain, respectively, are investigated, which further enhance the authentication reliability and efficiency in LEO constellation. Experiments on OPNET simulation platform evaluate and demonstrate the effectiveness, reliability, and fast-switching efficiency of the proposed protocol. For LEO networks, BAVP surpasses the well-known existing solutions with significant advantages in both performance and scalability which are supported by theoretical analysis and simulation results.

Environmental Impacts and Embodied Energy of Construction Methods and Materials in Low-Income Tropical Housing

Directory of Open Access Journals (Sweden)

Arman Hashemi

2015-06-01

Full Text Available This paper evaluates the current conditions of Ugandan low-income tropical housing with a focus on construction methods and materials in order to identify the key areas for improvement. Literature review, site visits and photographic surveys are carried out to collect relevant information on prevailing construction methods/materials and on their environmental impacts in rural areas. Low quality, high waste, and energy intensive production methods, as well as excessive soil extraction and deforestation, are identified as the main environmental damage of the current construction methods and materials. The embodied energy is highlighted as the key area which should be addressed to reduce the CO2 emissions of low-income tropical housing. The results indicate that the embodied energy of fired bricks in Uganda is up to 5.7 times more than general clay bricks. Concrete walling is identified as a much more environmentally friendly construction method compared to brick walling in East African countries. Improving fuel efficiency and moulding systems, increasing access to renewable energy sources, raising public awareness, educating local manufacturers and artisans, and gradual long-term introduction of innovative construction methods and materials which are adapted to local needs and conditions are some of the recommended actions to improve the current conditions.

Radiometric analysis of construction materials using HPGe gamma-ray spectrometry.

Science.gov (United States)

Khandaker, M U; Jojo, P J; Kassim, H A; Amin, Y M

2012-11-01

Concentrations of primordial radionuclides in common construction materials collected from the south-west coastal region of India were determined using a high-purity germanium gamma-ray spectrometer. Average specific activities (Bq kg(-1)) for (238)U((226)Ra) in cement, brick, soil and stone samples were obtained as 54 ± 13, 21 ± 4, 50 ± 12 and 46 ± 8, respectively. Respective values of (232)Th were obtained as 65 ± 10, 21 ± 3, 58 ± 10 and 57 ± 12. Concentrations of (40)K radionuclide in cement, brick, soil and stone samples were found to be 440 ± 91, 290 ± 20, 380 ± 61 and 432 ± 64, respectively. To evaluate the radiological hazards, radium equivalent activity, various hazard indices, absorbed dose rate and annual effective dose have been calculated, and compared with the literature values. Obtained data could be used as reference information to assess any radiological contamination due to construction materials in future.

Construction cost impacts related to manpower, material, and equipment factors in contractor firms perspective

Science.gov (United States)

Husin, Saiful; Abdullah, Riza, Medyan; Afifuddin, Mochammad

2017-11-01

Risk can be defined as consequences which possible happened inscrutably. Although an activity has planned as good as possible, but it keep contains uncertainty. Implementation of construction project was encountering various risk impacts from a number of risk factors. This study was intended to analyze the impacts of construction cost to for contractor firms as construction project executor related to the factors of manpower, material and equipment. The study was using data obtained from questionnaires distributed to 15 large qualification contractor firms. The period of study classified into conflict period (2000-2004), post tsunami disaster rehabilitation and reconstruction period (2005-2009), and post rehabilitation and reconstruction period (2010-present). The statistical analysis of severity index and variance used to analyze the data. The three risk factors reviewed generally affected the cost in a medium impact. The high impact occurred in minor variables, which are `increase in material prices', `theft of materials', and `the fuel scarcity'. In overall, the three risk factors and the observed period contributed significant impact on construction costs.

Program-oriented approach to resource saving issues in construction materials industry

Directory of Open Access Journals (Sweden)

Novikova Galina

2017-01-01

Full Text Available The construction as a sector of the economy is one of the largest consumers of energy resources, and the building materials industry is today one of the most energy-intensive construction industry. At the enterprises of the building materials industry the different approaches and methods are used to solve resource and energy problems. Energy saving is considered not as an complex approach in the enterprise activity, but as activity for the implementation of specific energy-saving projects, which have limitations in time and in resources. The authors suggest to use a softwareoriented approach to solving the problems of resource and energy saving. For practical application of program-oriented approach we offer to use a structuring method of the decision-making, not previously used to solve problems of resource and energy saving.

Radiation properties of moving constellations of (nano) satellites: A complexity study

NARCIS (Netherlands)

Bruinsma, Wessel P.; Hes, Robin P.; Bosma, Sjoerd; Lager, Ioan E.; Bentum, Marinus Jan

2016-01-01

The (computational) complexity involved by beamforming in moving constellations of (nano) satellites is investigated by means of illustrative numerical experiments. While the number of radiators in such three-dimensional (3D) array antennas is not large, evaluating their radiation patterns entails

Fabrication of Porous Ceramic-Geopolymer Based Material to Improve Water Absorption and Retention in Construction Materials: A Review

Science.gov (United States)

Jamil, N. H.; Ibrahim, W. M. A. W.; Abdullah, M. M. A. B.; Sandu, A. V.; Tahir, M. F. M.

2017-06-01

Porous ceramic nowadays has been investigated for a variety of its application such as filters, lightweight structural component and others due to their specific properties such as high surface area, stability and permeability. Besides, it has the properties of low thermal conductivity. Various formation techniques making these porous ceramic properties can be tailored or further fine-tuned to obtain the optimum characteristic. Porous materials also one of the good candidate for absorption properties. Conventional construction materials are not design to have good water absorption and retention that lead to the poor performance on these criteria. Temperature is a major driving force for moisture movement and influences sorption characteristics of many constructions materials. The effect of elevated temperatures on the water absorption coefficient and retention remain as critical issue that need to be investigated. Therefore, this paper will review the process parameters in fabricating porous ceramic for absorption properties.

Lunar materials for construction of space manufacturing facilities

Science.gov (United States)

Criswell, D. R.

1977-01-01

Development of industrial operations in deep space would be prohibitively expensive if most of the construction and expendable masses had to be transported from earth. Use of lunar materials reduces the needed investments by a factor of 15 to 20. It is shown in this paper that judicious selection of lunar materials will allow one to obtain hydrogen, nitrogen, carbon, helium and other specific elements critical to the support of life in large space habitats at relatively low costs and lower total investment even further. Necessary selection techniques and extraction schemes are outlined. In addition, tables are presented of the oxide and elemental abundances characteristic of the mare and highland regions of the moon which should be useful in evaluating what can be extracted from the lunar soils.

Improvement of the material and transport component of the system of construction waste management

Science.gov (United States)

Kostyshak, Mikhail; Lunyakov, Mikhail

2017-10-01

Relevance of the topic of selected research is conditioned with the growth of construction operations and growth rates of construction and demolition wastes. This article considers modern approaches to the management of turnover of construction waste, sequence of reconstruction or demolition processes of the building, information flow of the complete cycle of turnover of construction and demolition waste, methods for improvement of the material and transport component of the construction waste management system. Performed analysis showed that mechanism of management of construction waste allows to increase efficiency and environmental safety of this branch and regions.

Superface energy of several construction materials

Directory of Open Access Journals (Sweden)

Otero, J. L.

2006-09-01

Full Text Available Inverse gas chromatography at infinite dilution was used to characterize the surface of different construction materials (marble, sandstone, granite and brick. Surface energy can be divided into two components: dispersive and polar or acid-base. The highest dispersive energy value was found for sandstone, while the values for the other three materials were all very similar. The lower dispersive energy variation exhibited by sandstone with temperature changes is an indication that substances interact equally well with its surface at any temperature. All the materials were found to be amphoteric, with both acid and alkaline components, although acidity was greater in granite and brick and sandstone and marble had higher alkalinity.En este trabajo se ha realizado la caracterización de la superficie de diferentes materiales de construcción (mármol,arenisca, granito y ladrillo mediante cromatografía inversa gas-sólido a dilución infinita. La energía superficial se puede dividir en dos componentes: dispersiva y ácido-base. Los valores obtenidos para la energía dispersiva son bastante parecidas para mármol, granito y ladrillo, mientras que el valor más alto corresponde a la arenisca. Además, este material presenta una menor variación de la energía dispersiva con la temperatura lo que indica que la interacción de cualquier sustancia con su superficie se dará a cualquier temperatura. Por lo que respecta a las componentes ácido-base, se ha observado que todos los materiales poseen ambas componentes lo que indica un carácter anfótero, sin embargo, la acidez es mayor en el granito y en el ladrillo, mientras que la basicidad es mayor en la arenisca y en el mármol.

Symbolics of the constellations of sagittarius and centaurus in russian traditional culture

Science.gov (United States)

Bagdasarov, R.

2001-12-01

Centaurus falls into the category of 'imaginary animals'. The Russian tradition used not only the symbol Sgr (a result of its acquaintance with the circle of Zodiac), but also the symbol Cen, which fact, as we shall demonstrate, is an evidence of certain mythological-astronomical conceptions. Both the constellations Sagittarius (Sgr) and Centaurus (Cen) are usually represented as versions of the picture of a fantastic being, a Centaur, shaped as man from head to waist, and as an animal, mostly, a horse, from waist down. 'Centaurus' (from the Greek word kev (or kevw)) for 'kill' and o, for 'bull') means 'bull killer', and is probably related to the opposition of the zodiacal constellations Taurus and Sagittarius. When the latter begins to rise on to the night sky, the former disappears completely from view. Sagittarius is represented at ancient monuments related to astronomy as a centaur holding a bow and pointing at certain stars. The constellation of Centaurus is also symbolised by a centaur, but holding not a bow, but a staff or a spear in one hand and an 'animal of sacrifice' in the other (Higinus, Astronomica, III, 37, 1; Chernetsov, 1975, Figure 1). The attributes stand for the Peliases Spear (The Mithological Dictionary, 1991), depicted in astrological maps as The Spear of Centaurus1, The Wolf (Lupus), the Panther or the Beast (Flammarion, 1994).

A framework of analysis for field experiments with alternative materials in road construction.

Science.gov (United States)

François, D; Jullien, A

2009-01-01

In France, a wide variety of alternative materials is produced or exists in the form of stockpiles built up over time. Such materials are distributed over various regions of the territory depending on local industrial development and urbanisation trends. The use of alternative materials at a national scale implies sharing local knowledge and experience. Building a national database on alternative materials for road construction is useful in gathering and sharing information. An analysis of feedback from onsite experiences (back analysis) is essential to improve knowledge on alternative material use in road construction. Back analysis of field studies has to be conducted in accordance with a single common framework. This could enable drawing comparisons between alternative materials and between road applications. A framework for the identification and classification of data used in back analyses is proposed. Since the road structure is an open system, this framework has been based on a stress-response approach at both the material and structural levels and includes a description of external factors applying during the road service life. The proposal has been shaped from a review of the essential characteristics of road materials and structures, as well as from the state of knowledge specific to alternative material characterisation.

Neutron diffraction measurements of residual stresses in NPP construction materials

International Nuclear Information System (INIS)

Hinca, R.; Bokuchava, G.

2001-01-01

Neutron diffraction is one of the most powerful methods for condensed matter studies. This method is used for non-destructive determination of residual stresses in material. The fundamental aspects of neutron diffraction are discussed, together with a brief description of the experimental facility. The principal advantage of using neutrons rather than the more conventional X-rays is the fact that neutron can penetrate deeply (2-4 cm for steel and more than 10 cm for aluminium) into metals to determine internal parameters within the bulk of materials. We present results of measurements residual stresses in NPP construction material - austenitic stainless steel (Cr-18%, Ni-10%, Ti-1%) coated with high-nickel alloy. (authors)

Generalized BICM-T transceivers: Constellation and multiplexer design

KAUST Repository

Malik, Muhammad Talha

2013-09-01

Recently, it has been shown that the performance of bit-interleaved coded modulation (BICM) using convolutional codes in nonfading channels can be significantly improved if the coded bits are not interleaved at all. This particular BICM design is referred to as BICM trivial (BICM-T) and is shown to be asymptotically as good as Ungerboeck\\'s one dimensional (1D) trellis coded modulation (TCM). This BICM-T design and analysis considered a simple case of rate 1/2 channel encoder with equally spaced 16-ary quadrature amplitude modulation (QAM) constellation where the code rate matches with the modulation order as required in TCM transmission. In this paper, we consider and analyze a new BICM-T design that uses a non equally spaced signal constellation in conjunction with a bit level multiplexer. With this design and analysis, one can not only exploit the full benefit of BICM-T design by jointly optimizing different transceiver\\'s modules but also enjoys the same design flexibility as the traditional BICM to independently choose the code rate and the modulation order. The presented numerical results for 64-ary QAM with rate 1/3 code shows that the considered design can offer gains up to 2.5 dB over the traditional optimal BICM design for a target bit error rate (BER) of 10-6. © 2013 IEEE.

Heuristic economic assessment of the Afghanistan construction materials sector: cement and dimension stone production

Science.gov (United States)

Mossotti, Victor G.

2014-01-01

Over the past decade, the U.S. Government has invested more than $106 billion for physical, societal, and governmental reconstruction assistance to Afghanistan (Special Inspector General for Afghanistan Reconstruction, 2012a). This funding, along with private investment, has stimulated a growing demand for particular industrial minerals and construction materials. In support of this effort, the U.S. Geological Survey released a preliminary mineral assessment in 2007 on selected Afghan nonfuel minerals (Peters and others, 2007). More recently, the 2007 mineral assessment was updated with the inclusion of a more extensive array of Afghan nonfuel minerals (Peters and others, 2011). As a follow-up on the 2011 assessment, this report provides an analysis of the current use and prospects of the following Afghan industrial minerals required to manufacture construction materials: clays of various types, bauxite, gypsum, cement-grade limestone, aggregate (sand and gravel), and dimension stone (sandstone, quartzite, granite, slate, limestone, travertine, marble). The intention of this paper is to assess the: Use of Afghan industrial minerals to manufacture construction materials, Prospects for growth in domestic construction materials production sectors, Factors controlling the competitiveness of domestic production relative to foreign imports of construction materials, and Feasibility of using natural gas as the prime source of thermal energy and for generating electrical energy for cement production. The discussion here is based on classical principles of supply and demand. Imbedded in these principles is an understanding that the attributes of supply and demand are highly variable. For construction materials, demand for a given product may depend on seasons of the year, location of construction sites, product delivery time, political factors, governmental regulations, cultural issues, price, and how essential a given product might be to the buyer. Moreover, failure on the

Cubesat Constellation Design for Air Traffic Monitoring

Science.gov (United States)

Nag, Sreeja; Rios, Joseph Lucio; Gerhardt, David; Pham, Camvu

2015-01-01

Suitably equipped global and local air traffic can be tracked. The tracking information may then be used for control from ground-based stations by receiving the Automatic Dependent Surveillance-Broadcast (ADS-B) signal. The ADS-B signal, emitted from the aircraft's Mode-S transponder, is currently tracked by terrestrial based receivers but not over remote oceans or sparsely populated regions such as Alaska or the Pacific Ocean. Lack of real-time aircraft time/location information in remote areas significantly hinders optimal planning and control because bigger "safety bubbles" (lateral and vertical separation) are required around the aircraft until they reach radar-controlled airspace. Moreover, it presents a search-and-rescue bottleneck. Aircraft in distress, e.g. Air France AF449 that crashed in 2009, take days to be located or cannot be located at all, e.g. Malaysia Airlines MH370 in 2014. In this paper, we describe a tool for designing a constellation of small satellites which demonstrates, through high-fidelity modeling based on simulated air traffic data, the value of space-based ADS-B monitoring and provides recommendations for cost-efficient deployment of a constellation of small satellites to increase safety and situational awareness in the currently poorly-served surveillance area of Alaska. Air traffic data has been obtained from the Future ATM Concepts Evaluation Tool (FACET), developed at NASA Ames Research Center, simulated over the Alaskan airspace over a period of one day. The simulation is driven by MATLAB with satellites propagated and coverage calculated using AGI's Satellite ToolKit(STK10).

Measurement of color in different construction materials. The restoration in sandstone buildings

Directory of Open Access Journals (Sweden)

García Pascua, N.

1999-03-01

Full Text Available The use of construction materials and their subsequent repair purposes include a search of knowledge and preservation of their original appearance. For this reason, the main aim of this study is to determine a color range which does not change with the possible actions on a building, both when restoration works which imply the use and repair of "ancient" materials are carried out, and when construction is carried out with new materials. It is necessary to obtain the quantification of this property in order to check its variation over the passage of time. Each construction material must be taken into account as an isolated problem, since the color is different in each case.

El empleo de materiales de construcción y la aplicación sobre ellos de productos de reparación requiere un detallado estudio sobre su forma de actuación y la importancia de la conservación del aspecto original de los mismos. Por este motivo, el objetivo principal de este estudio es el determinar un intervalo de color que se conserve a pesar de todas las posibles intervenciones que se acometan en el edificio, tanto cuando se realizan trabajos de restauración, que implican el uso y reparación de materiales "viejos", o bien cuando se llevan a cabo trabajos de construcción con materiales nuevos. Es necesario cuantificar dicha propiedad para poder controlar el paso del tiempo. Cada material de construcción debe ser considerado como un problema aislado, ya que el color es distinto en cada caso.

Does the Constellation Program Offer Opportunities to Achieve Space Science Goals in Space?

Science.gov (United States)

Thronson, Harley A.; Lester, Daniel F.; Dissel, Adam F.; Folta, David C.; Stevens, John; Budinoff, Jason G.

2008-01-01

Future space science missions developed to achieve the most ambitious goals are likely to be complex, large, publicly and professionally very important, and at the limit of affordability. Consequently, it may be valuable if such missions can be upgraded, repaired, and/or deployed in space, either with robots or with astronauts. In response to a Request for Information from the US National Research Council panel on Science Opportunities Enabled by NASA's Constellation System, we developed a concept for astronaut-based in-space servicing at the Earth-Moon L1,2 locations that may be implemented by using elements of NASA's Constellation architecture. This libration point jobsite could be of great value for major heliospheric and astronomy missions operating at Earth-Sun Lagrange points. We explored five alternative servicing options that plausibly would be available within about a decade. We highlight one that we believe is both the least costly and most efficiently uses Constellation hardware that appears to be available by mid-next decade: the Ares I launch vehicle, Orion/Crew Exploration Vehicle, Centaur vehicle, and an airlock/servicing node developed for lunar surface operations. Our concept may be considered similar to the Apollo 8 mission: a valuable exercise before descent by astronauts to the lunar surface.

Weight and cost analysis of large wind turbine rotors constructed from conventional materials and from advanced composite materials

Energy Technology Data Exchange (ETDEWEB)

van Holten, Th

1982-07-01

Cost calculations and cost analyses of the blades and the (teetering) hubs of large wind turbines. The blades are of different shapes, construction and materials (aluminium, steel and glass reinforced plastics). Teetering hubs are heavy and complicated steel constructions, necessary to minimize material fatigue. In large wind turbines with a diameter of 60 to 100 m or even more the rotor mass (hubs and blades together) may vary from 46,000 to 216,000 kg. Costs are estimated to be DFL. 16/kg, both for teetering hubs and/or blades made of glass reinforced plastics. Due to lack of experience and of exact knowledge of the loads appearing during operation under field conditions the uncertainty factor may be 10% to 15%.

Determination of radon exhalation from construction materials using VOC emission test chambers.

Science.gov (United States)

Richter, M; Jann, O; Kemski, J; Schneider, U; Krocker, C; Hoffmann, B

2013-10-01

The inhalation of (222) Rn (radon) decay products is one of the most important reasons for lung cancer after smoking. Stony building materials are an important source of indoor radon. This article describes the determination of the exhalation rate of stony construction materials by the use of commercially available measuring devices in combination with VOC emission test chambers. Five materials - two types of clay brick, clinker brick, light-weight concrete brick, and honeycomb brick - generally used for wall constructions were used for the experiments. Their contribution to real room concentrations was estimated by applying room model parameters given in ISO 16000-9, RP 112, and AgBB. This knowledge can be relevant, if for instance indoor radon concentration is limited by law. The test set-up used here is well suited for application in test laboratories dealing with VOC emission testing. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Application of RFID combined with blockchain technology in logistics of construction materials

Directory of Open Access Journals (Sweden)

Lanko A.

2018-01-01

Full Text Available Nowadays, almost none of the fields of human activity can do without supply chain management. In addition, implementation of one in construction companies contributes to major economic benefits. The article considers the application feasibility of blockchain in logistics of construction materials through the usage of RFID technology. An example of introduction to the process of manufacturing and delivery of ready-mixed concrete is given. The main advantages, shortcomings, perspectives, as well as difficulties arising in the implementation of blockchain technology in the construction industry are described. Special attention is paid to the applicability of these technologies.

Ion irradiation studies of construction materials for high-power accelerators

Science.gov (United States)

Mustafin, E.; Seidl, T.; Plotnikov, A.; Strašík, I.; Pavlović, M.; Miglierini, M.; Stanćek, S.; Fertman, A.; Lanćok, A.

The paper reviews the activities and reports the current results of GSI-INTAS projects that are dealing with investigations of construction materials for high-power accelerators and their components. Three types of materials have been investigated, namely metals (stainless steel and copper), metallic glasses (Nanoperm, Finemet and Vitrovac) and organic materials (polyimide insulators and glass fiber reinforced plastics/GFRP). The materials were irradiated by different ion beams with various fluencies and energies. The influence of radiation on selected physical properties of these materials has been investigated with the aid of gamma-ray spectroscopy, transmission Mössbauer spectroscopy (TMS), conversion electrons Mössbauer spectroscopy (CEMS), optical spectroscopy (IR and UV/VIS) and other analytical methods. Some experiments were accompanied with computer simulations by FLUKA, SHIELD and SRIM codes. Validity of the codes was verified by comparison of the simulation results with experiments. After the validation, the codes were used to complete the data that could not be obtained experimentally.

Kinematic-PPP using Single/Dual Frequency Observations from (GPS, GLONASS and GPS/GLONASS) Constellations for Hydrography

Science.gov (United States)

Farah, Ashraf

2018-03-01

Global Positioning System (GPS) technology is ideally suited for inshore and offshore positioning because of its high accuracy and the short observation time required for a position fix. Precise point positioning (PPP) is a technique used for position computation with a high accuracy using a single GNSS receiver. It relies on highly accurate satellite position and clock data that can be acquired from different sources such as the International GNSS Service (IGS). PPP precision varies based on positioning technique (static or kinematic), observations type (single or dual frequency) and the duration of observations among other factors. PPP offers comparable accuracy to differential GPS with safe in cost and time. For many years, PPP users depended on GPS (American system) which considered the solely reliable system. GLONASS's contribution in PPP techniques was limited due to fail in maintaining full constellation. Yet, GLONASS limited observations could be integrated into GPS-based PPP to improve availability and precision. As GLONASS reached its full constellation early 2013, there is a wide interest in PPP systems based on GLONASS only and independent of GPS. This paper investigates the performance of kinematic PPP solution for the hydrographic applications in the Nile river (Aswan, Egypt) based on GPS, GLONASS and GPS/GLONASS constellations. The study investigates also the effect of using two different observation types; single-frequency and dual frequency observations from the tested constellations.

Constructing Ontology for Knowledge Sharing of Materials Failure Analysis

Directory of Open Access Journals (Sweden)

Peng Shi

2014-01-01

Full Text Available Materials failure indicates the fault with materials or components during their performance. To avoid the reoccurrence of similar failures, materials failure analysis is executed to investigate the reasons for the failure and to propose improved strategies. The whole procedure needs sufficient domain knowledge and also produces valuable new knowledge. However, the information about the materials failure analysis is usually retained by the domain expert, and its sharing is technically difficult. This phenomenon may seriously reduce the efficiency and decrease the veracity of the failure analysis. To solve this problem, this paper adopts ontology, a novel technology from the Semantic Web, as a tool for knowledge representation and sharing and describes the construction of the ontology to obtain information concerning the failure analysis, application area, materials, and failure cases. The ontology represented information is machine-understandable and can be easily shared through the Internet. At the same time, failure case intelligent retrieval, advanced statistics, and even automatic reasoning can be accomplished based on ontology represented knowledge. Obviously this can promote the knowledge sharing of materials service safety and improve the efficiency of failure analysis. The case of a nuclear power plant area is presented to show the details and benefits of this method.

Naturally occurring radioactive materials in construction integrating radiation protection in Reuse

CERN Document Server

Schroeyers, Wouter

2017-01-01

Naturally Occurring Radioactive Materials in Construction (COST Action NORM4Building) discusses the depletion of energy resources and raw materials and its huge impact not only on the building market, but also in the development of new synthetic building materials, whereby the reuse of various (waste) residue streams becomes a necessity. It is based on the outcome of COST Action TU 1301, where scientists, regulators, and representatives from industry have come together to present new findings, sharing knowledge, experiences, and technologies to stimulate research on the reuse of residues containing enhanced concentrates of natural radionuclides (NORM) in tailor-made building materials. Chapters address legislative issues, measurement, and assessment of building materials, physical and chemical aspects, from raw materials, to residues with enhanced concentrations of natural radionuclides (NORM), processes, building products containing NORM, and end-of-life and reuse requirements. Presents a holistic app...

The use of shale ash in dry mix construction materials

Science.gov (United States)

Gulbe, L.; Setina, J.; Juhnevica, I.

2017-10-01

The research was made to determine the use of shale ash usage in dry mix construction materials by replacing part of cement amount. Cement mortar ZM produced by SIA Sakret and two types of shale ashes from Narva Power plant (cyclone ash and electrostatic precipitator ash) were used. Fresh mortar properties, hardened mortar bulk density, thermal conductivity (λ10, dry) (table value) were tested in mortar ZM samples and mortar samples in which 20% of the amount of cement was replaced by ash. Compressive strenght, frost resistance and resistance to sulphate salt solutions were checked. It was stated that the use of electrostatic precipitator ash had a little change of the material properties, but the cyclone ash significantly reduced the mechanical strength of the material.

Mix design and mechanical performance of geopolymer binder for sustainable construction and building material

Science.gov (United States)

Saeli, Manfredi; Novais, Rui M.; Seabra, Maria Paula; Labrincha, João A.

2017-11-01

Sustainability in construction is a major concern worldwide, due to the huge volume of materials and energy consumed by this sector. Associated supplementing industries (e.g. Portland cement production) constitute a significant source of CO2 emissions and global warming. Valorisation and reuse of industrial wastes and by-products make geopolymers a solid and sustainable via to be followed as a valid alternative to Portland cement. In this work the mix design of a green fly ash-based geopolymer is evaluated as an environmentally friendly construction material. In the pursuit of sustainability, wastes from a regional kraft pulp industry are exploited for the material processing. Furthermore, a simple, reproducible, and low-cost manufacture is used. The mix design is hence optimised in order to improve the desirable mechanical performance of the material intended for structural applications in construction. Tests indicate that geopolymers may efficiently substitute the ordinary Portland cement as a mortar/concrete binder. Furthermore, valorisation and reuse of wastes in geopolymers is a suboptimal way of gaining financial surplus for the involved industrial players, while contributes for the implementation of a desirable circular economy.

Reuse of conditional released materials from decommissioning; a review of approaches and scenarios with long-term constructions - 59149

International Nuclear Information System (INIS)

Daniska, Vladimir; Pritrsky, Jozef; Ondra, Frantisek; Zachar, Matej; Necas, Vladimir

2012-01-01

Paper presents the overall scope and actual results of the project for evaluation of representative scenarios for reuse of conditionally released materials from decommissioning. Aim of the project is to evaluate the possibilities of reuse of conditionally released steels and concrete in technical constructions which guarantee the long-term preservation of design properties over periods of 50-100 years. Interaction of conditionally released materials with public is limited and predictable due to design and purpose of selected constructions and due to fact that in many scenarios these materials are embedded in non-radioactive materials such as bars in reinforced concrete. Worker's scenarios for preparation, operation and maintenance of these constructions are analysed in detail including the manufacturing of elements for these constructions. Project aims to evaluate the scenarios of reuse of conditionally released materials in a complex way in order to develop the data for designers of scenarios and to evaluate the volumes of conditionally released materials based on facility (to be decommissioned) inventory data. The long-term constructions considered are bridges, tunnels, roads, railway constructions, industrial buildings, power industry equipment and others. Evaluation covers following areas: - Analysis of activities for manufacturing of reinforcement bars, rolled steel sheets and other steel elements and analysis of activities for construction of evaluated scenarios in order to evaluate the external exposure of professionals performing these activities; - Analysis of external exposure of professionals involved in operation and maintenance of the long-term constructions; analysis of external exposure of public groups which are exposed to evaluated constructions; - Analysis of internal exposure of public groups from the radionuclides released from the evaluated scenarios based on models for migration of radionuclides from the long-term constructions to critical

The CEOS-Land Surface Imaging Constellation Portal for GEOSS: A resource for land surface imaging system information and data access

Science.gov (United States)

Holm, Thomas; Gallo, Kevin P.; Bailey, Bryan

2010-01-01

The Committee on Earth Observation Satellites is an international group that coordinates civil space-borne observations of the Earth, and provides the space component of the Global Earth Observing System of Systems (GEOSS). The CEOS Virtual Constellations concept was implemented in an effort to engage and coordinate disparate Earth observing programs of CEOS member agencies and ultimately facilitate their contribution in supplying the space-based observations required to satisfy the requirements of the GEOSS. The CEOS initially established Study Teams for four prototype constellations that included precipitation, land surface imaging, ocean surface topography, and atmospheric composition. The basic mission of the Land Surface Imaging (LSI) Constellation [1] is to promote the efficient, effective, and comprehensive collection, distribution, and application of space-acquired image data of the global land surface, especially to meet societal needs of the global population, such as those addressed by the nine Group on Earth Observations (GEO) Societal Benefit Areas (SBAs) of agriculture, biodiversity, climate, disasters, ecosystems, energy, health, water, and weather. The LSI Constellation Portal is the result of an effort to address important goals within the LSI Constellation mission and provide resources to assist in planning for future space missions that might further contribute to meeting those goals.

Feasibility of coal fly ash based bricks and roof tiles as construction materials: a review

Directory of Open Access Journals (Sweden)

Akhtar M.N.

2017-01-01

Full Text Available The aim of present study is to investigate about the potential use of coal fly ash along with other natural and solid wastes for the production of coal fly ash based bricks and roof tiles. The study is based on the comprehensive reviews available from the previous experimental data on coal fly ash based bricks and roof tiles. The study intendeds to provide the essential technical information and data for the use of fly ash mix with other solid wastes and reveal their suitability as construction materials. It has been found that samples were non-hazardous in nature and vigorously used as an additional construction materials and their compositions are perfectly fit to make the strong composite material for bricks and tiles. The three past studies have been demonstrated that, fly ash based bricks and roof tiles provides a sustainable supplement to the traditional clay bricks and roof tiles, that not only increases the efficiency of traditional bricks and roof tiles but also helps significantly to reduce the environmental issues associated with the disposal of these waste materials. In addition to this study highlights the potential use of fly ash for producing sustainable construction materials.

Construction Time of Three Wall Types Made of Locally Sourced Materials: A Comparative Study

OpenAIRE

Wojciech Drozd; Agnieszka Leśniak; Sebastian Zaworski

2018-01-01

Similarly to any other industry, the construction sector puts emphasis on innovativeness, unconventional thinking, and alternative ideas. At present, when sustainable development, ecology, and awareness of people’s impact on the environment grow in importance, low impact buildings can become an innovative alternative construction technology for the highly industrialized construction sector. The paper presents a comparative study of three walls made of available materials used locally, which c...

Optimizing the Attitude Control of Small Satellite Constellations for Rapid Response Imaging

Science.gov (United States)

Nag, S.; Li, A.

2016-12-01

Distributed Space Missions (DSMs) such as formation flight and constellations, are being recognized as important solutions to increase measurement samples over space and time. Given the increasingly accurate attitude control systems emerging in the commercial market, small spacecraft now have the ability to slew and point within few minutes of notice. In spite of hardware development in CubeSats at the payload (e.g. NASA InVEST) and subsystems (e.g. Blue Canyon Technologies), software development for tradespace analysis in constellation design (e.g. Goddard's TAT-C), planning and scheduling development in single spacecraft (e.g. GEO-CAPE) and aerial flight path optimizations for UAVs (e.g. NASA Sensor Web), there is a gap in open-source, open-access software tools for planning and scheduling distributed satellite operations in terms of pointing and observing targets. This paper will demonstrate results from a tool being developed for scheduling pointing operations of narrow field-of-view (FOV) sensors over mission lifetime to maximize metrics such as global coverage and revisit statistics. Past research has shown the need for at least fourteen satellites to cover the Earth globally everyday using a LandSat-like sensor. Increasing the FOV three times reduces the need to four satellites, however adds image distortion and BRDF complexities to the observed reflectance. If narrow FOV sensors on a small satellite constellation were commanded using robust algorithms to slew their sensor dynamically, they would be able to coordinately cover the global landmass much faster without compensating for spatial resolution or BRDF effects. Our algorithm to optimize constellation satellite pointing is based on a dynamic programming approach under the constraints of orbital mechanics and existing attitude control systems for small satellites. As a case study for our algorithm, we minimize the time required to cover the 17000 Landsat images with maximum signal to noise ratio fall

SAC-C Mission and the Morning Constellation

Science.gov (United States)

Colomb, F. R.; Alonso, C.; Hofmann, C.; Frulla, L.; Nollmann, I.; Milovich, J.; Kuba, J.; Ares, F.; Kalemkarian, M.

2002-01-01

components (ICARE), provided by CNES will permit improvement of risk estimation models for radiation effect on last generation integrated circuit technology. . On June 14th, 2000 CONAE and NASA signed an amendment to the Memorandum of Understanding for the SAC-C mission in order that the SAC-C satellite, were included in a constellation - named "Morning Constellation". It is integrated by USA satellites Landsat 7, EO 1, Terra, and Argentine SAC-C that feature on-board instruments from the United States, Argentina, Denmark, Italy, France, and Japan. The four satellite tracks on the Earth's surface are the same, their orbital height being 705 km and their inclination, 98.21 degrees. They cross the Equator at 10:00, 10:01, 10:15, and 10:30 hours, respectively (local time). Satellites comply with the World Wide Reference System. The Constellation has been working since March 2001 as a single mission and several cooperative activities have been undertaken and will be presented in this paper. Several jointly sponsored technical workshops have been held, and also collaborative spacecraft navigation experiments have been made. One of the objectives of the AM Constellation is the collaboration in the case of emergencies, NASA and CONAE agreed to give preference in those situation in the planification of their satellite acquisitions. From all the possible hazardous events, the most important for the country are fire and floods. In relation to fires, CONAE is presently adapting and developing the algorithms for using MODIS data to generate a fire map product. Additionally research on fire detection is carried out using the data from the HSTC camera. In relation to flooding, CONAE works in cooperation to national institutions providing the data and, in some cases, producing flood extent maps. In particular MMRS data is demonstrating to be very effective due to its spectral and radiometric resolutions, and its large swath which is well suited for extended countries like Argentina.

Natural disaster reduction applications of the Chinese small satellite constellation for environment and disaster monitoring and forecasting

Science.gov (United States)

Liu, Sanchao; Fan, Yida; Gao, Maofang

2013-10-01

The Small Satellite Constellation for Environment and Disaster Monitoring and Forecasting (SSCEDMF) is an important component of Chinese satellites earth observation system. The first stage of SSCEDMF is composed by "2+1" satellites. The 2 optical satellites (HJ-1-A and HJ-1-B) and 1 S band microwave satellite (HJ-1-C) were successful launched on September 6, 2008 and November 19, 2012 respectively. This article introduced SSCEDMF characteristic and the disaster reduction application system and satellites on-orbit test works, and also analyzed the application capacity in natural disasters included flood, ice flooding, wild fire, severely drought, snow disasters, large area landslide and debris flow, sea ice, earthquake recovering, desertification and plant diseases and insect pests. Furthermore, we show some cases of China's and other countries' new natural disasters forecasting, monitoring, assessment and recovery construction.

The design and networking of dynamic satellite constellations for global mobile communication systems

Science.gov (United States)

Cullen, Cionaith J.; Benedicto, Xavier; Tafazolli, Rahim; Evans, Barry

1993-01-01

Various design factors for mobile satellite systems, whose aim is to provide worldwide voice and data communications to users with hand-held terminals, are examined. Two network segments are identified - the ground segment (GS) and the space segment (SS) - and are seen to be highly dependent on each other. The overall architecture must therefore be adapted to both of these segments, rather than each being optimized according to its own criteria. Terrestrial networks are grouped and called the terrestrial segment (TS). In the SS, of fundamental importance is the constellation altitude. The effect of the altitude on decisions such as constellation design choice and on network aspects like call handover statistics are fundamental. Orbit resonance is introduced and referred to throughout. It is specifically examined for its useful properties relating to GS/SS connectivities.

Material characteristics and construction methods for a typical research reactor concrete containment in Iran

International Nuclear Information System (INIS)

Ebrahimia, Mahsa; Suha, Kune Y.; Eghbalic, Rahman; Jahan, Farzaneh Asadi malek

2012-01-01

Generally selecting an appropriate material and also construction style for a concrete containment due to its function and special geometry play an important role in applicability and also construction cost and duration decrease in a research reactor (RR) project. The reactor containment enclosing the reactor vessel comprises physical barriers reflecting the safety design and construction codes, regulations and standards so as to prevent the community and the environment from uncontrolled release of radioactive materials. It is the third and the last barrier against radioactivity release. It protects the reactor vessel from such external events as earthquake and aircraft crash as well. Thus, it should be designed and constructed in such a manner as to withstand dead and live loads, ground and seismic loads, missiles and aircraft loads, and thermal and shrinkage loads. This study aims to present a construction method for concrete containment of a typical RR in Iran. The work also presents an acceptable characteristic for concrete and reinforcing re bar of a typical concrete containment. The current study has evaluated the various types of the RR containments. The most proper type was selected in accordance with the current knowledge and technology of Iran

Material characteristics and construction methods for a typical research reactor concrete containment in Iran

Energy Technology Data Exchange (ETDEWEB)

Ebrahimia, Mahsa; Suha, Kune Y. [Seoul National Univ., Seoul (Korea, Republic of); Eghbalic, Rahman; Jahan, Farzaneh Asadi malek [School of Architecture and Urbanism, Qazvin (Iran, Islamic Republic of)

2012-10-15

Generally selecting an appropriate material and also construction style for a concrete containment due to its function and special geometry play an important role in applicability and also construction cost and duration decrease in a research reactor (RR) project. The reactor containment enclosing the reactor vessel comprises physical barriers reflecting the safety design and construction codes, regulations and standards so as to prevent the community and the environment from uncontrolled release of radioactive materials. It is the third and the last barrier against radioactivity release. It protects the reactor vessel from such external events as earthquake and aircraft crash as well. Thus, it should be designed and constructed in such a manner as to withstand dead and live loads, ground and seismic loads, missiles and aircraft loads, and thermal and shrinkage loads. This study aims to present a construction method for concrete containment of a typical RR in Iran. The work also presents an acceptable characteristic for concrete and reinforcing re bar of a typical concrete containment. The current study has evaluated the various types of the RR containments. The most proper type was selected in accordance with the current knowledge and technology of Iran.

Nonlinear pre-coding apparatus of multi-antenna system, has pre-coding unit that extents original constellation points of modulated symbols to several constellation points by using limited perturbation vector

DEFF Research Database (Denmark)

2008-01-01

A Coding/Modulating units (200-1-200-N) outputs modulated symbols by modulating coding bit streams based on certain modulation scheme. The limited perturbation vector is calculated by using distribution of perturbation vectors. The original constellation points of modulated symbols are extended t...

Introducing Textiles as Material of Construction of Ethanol Bioreactors

Directory of Open Access Journals (Sweden)

Osagie A. Osadolor

2014-11-01

Full Text Available The conventional materials for constructing bioreactors for ethanol production are stainless and cladded carbon steel because of the corrosive behaviour of the fermenting media. As an alternative and cheaper material of construction, a novel textile bioreactor was developed and examined. The textile, coated with several layers to withstand the pressure, resist the chemicals inside the reactor and to be gas-proof was welded to form a 30 L lab reactor. The reactor had excellent performance for fermentative production of bioethanol from sugar using baker’s yeast. Experiments with temperature and mixing as process parameters were performed. No bacterial contamination was observed. Bioethanol was produced for all conditions considered with the optimum fermentation time of 15 h and ethanol yield of 0.48 g/g sucrose. The need for mixing and temperature control can be eliminated. Using a textile bioreactor at room temperature of 22 °C without mixing required 2.5 times longer retention time to produce bioethanol than at 30 °C with mixing. This will reduce the fermentation investment cost by 26% for an ethanol plant with capacity of 100,000 m3 ethanol/y. Also, replacing one 1300 m3 stainless steel reactor with 1300 m3 of the textile bioreactor in this plant will reduce the fermentation investment cost by 19%.

Simulating The Impact Of The Material Flow In The Jordanian Construction Supply Chain And Its Impact On Project Performance

Directory of Open Access Journals (Sweden)

Dr. Ghaith Al-Werikat

2017-03-01

Full Text Available With the new developments and challenges within the construction industry improving the construction supply chain is becoming a major concern to both governments and industries. Improving the construction supply chain helps in improving the quality of construction projects reducing cost wastes delays and other disruptions. This paper discusses the analysis of material flow in the construction supply chain. The methodology consisted of preliminary investigations survey and simulation development to analyse the extent of impact that material flow has on construction projects in Jordan. Both the main survey and the investigations revealed that material flow delays are caused mainly by 3 types of delays late delivery wrong specification and material damaged on site. The highest impact regarding late deliveries was scaffolding with a 16 probability of occurrence a 2-day delay on the activitys duration. Concrete ranked highest regarding wrong specification with a 19 probability of occurrence an 8-day delay the activitys duration. Regarding materials damaged on site bricks ranked highest with a 9 probability of occurrence a 3-day delay on the duration. The simulation results exhibited a delay of 50 on the projects duration and a probability of a delay occurring is 9.2.

Cost Effective Persistent Regional Surveillance with Reconfigurable Satellite Constellations

Science.gov (United States)

2015-04-24

GPIM AF-M315E Propulsion System,” 49th AIAA/ASME/SAE/ASEE Joint Propulsion Conference & Exhibit, San Jose , California, 15-17 July 2013, 2013. [15...earthquakes, floods, and volcanoes . The PDF, shown in Figure 11, is comprised of a 2.5 minute grid of global multi-hazard total economic loss risks...and Mortari, D., “The Lattice Theory of Flower Constellations,” Proceedings of the 2010 Space Flight Mechanics Meeting Conference. San Diego, CA

Asynchronous Processing of a Constellation of Geostationary and Polar-Orbiting Satellites for Fire Detection and Smoke Estimation

Science.gov (United States)

Hyer, E. J.; Peterson, D. A.; Curtis, C. A.; Schmidt, C. C.; Hoffman, J.; Prins, E. M.

2014-12-01

The Fire Locating and Monitoring of Burning Emissions (FLAMBE) system converts satellite observations of thermally anomalous pixels into spatially and temporally continuous estimates of smoke release from open biomass burning. This system currently processes data from a constellation of 5 geostationary and 2 polar-orbiting sensors. Additional sensors, including NPP VIIRS and the imager on the Korea COMS-1 geostationary satellite, will soon be added. This constellation experiences schedule changes and outages of various durations, making the set of available scenes for fire detection highly variable on an hourly and daily basis. Adding to the complexity, the latency of the satellite data is variable between and within sensors. FLAMBE shares with many fire detection systems the goal of detecting as many fires as possible as early as possible, but the FLAMBE system must also produce a consistent estimate of smoke production with minimal artifacts from the changing constellation. To achieve this, NRL has developed a system of asynchronous processing and cross-calibration that permits satellite data to be used as it arrives, while preserving the consistency of the smoke emission estimates. This talk describes the asynchronous data ingest methodology, including latency statistics for the constellation. We also provide an overview and show results from the system we have developed to normalize multi-sensor fire detection for consistency.

Materials-of-Construction Radiation Sensitivity for a Fission Surface Power Convertor

Science.gov (United States)

Bowman, Cheryl L.; Geng, Steven M.; Niedra, Janis M.; Sayir, Ali; Shin, Eugene E.; Sutter, James K.; Thieme, Lanny G.

2007-01-01

A fission reactor combined with a free-piston Stirling convertor is one of many credible approaches for producing electrical power in space applications. This study assumes dual-opposed free-piston Stirling engines/linear alternators that will operate nominally at 825 K hot-end and 425 K cold-end temperatures. The baseline design options, temperature profiles, and materials of construction discussed here are based on historical designs as well as modern convertors operating at lower power levels. This notional design indicates convertors primarily made of metallic components that experience minimal change in mechanical properties for fast neutron fluences less than 10(sup 20) neutrons per square centimeter. However, these radiation effects can impact the magnetic and electrical properties of metals at much lower fluences than are crucial for mechanical property integrity. Moreover, a variety of polymeric materials are also used in common free-piston Stirling designs for bonding, seals, lubrication, insulation and others. Polymers can be affected adversely by radiation doses as low as 10(sup 5) - 10(sup 10) rad. Additionally, the absorbing dose rate, radiation hardness, and the resulting effect (either hardening or softening) varies depending on the nature of the particular polymer. The classes of polymers currently used in convertor fabrication are discussed along possible substitution options. Thus, the materials of construction of prototypic Stirling convertor engines have been considered and the component materials susceptible to damage at the lowest neutron fluences have been identified.

Mission Status for Earth Science Constellation MOWG Meeting at KSC: EOS Aura

Science.gov (United States)

Fisher, Dominic

2017-01-01

This will be presented at the Earth Science Constellation Mission Operations Working Group (MOWG) meeting at KSC (Kennedy Space Center) in December 2017 to discus EOS (Earth Observing System) Aura status. Reviewed and approved by Eric Moyer, ESMO (Earth Sciences Mission Operations) Deputy Project Manager.

The HUMSAT System: a CubeSat-based Constellation for In-situ and Inexpensive Environmental Measurements

Science.gov (United States)

Tubío-Pardavila, R.; Vigil, S. A.; Puig-Suari, J.; Aguado Agelet, F.

2014-12-01

There is a requirement for low cost in-situ measurements of environmental parameters such as air quality, meteorological data, and water quality in remote areas. Currently available solutions for such measurements include remote sensing from satellite and aircraft platforms, and in-situ measurements from mobile and aircraft platforms. Fixed systems such as eddy covariance networks, tall towers, and the Total Carbon Column Observing Network (TCCON) are providing precision greenhouse gas measurements. Within this context, the HUMSAT system designed by the University of Vigo (Spain) will complement existing high-precision measurement systems with low cost in-situ ground based sensors in remote locations using a constellation of CubeSats as a communications relay. The HUMSAT system standardizes radio communications in between deployed sensors and the CubeSats of the constellation, which act as store and forward satellites to ground stations for uploading to the internet. Current ground stations have been established at the University of Vigo (Spain) and California Polytechnic State University (Cal Poly). Users of the system may deploy their own environmental sensors to meet local requirements. The sensors will be linked to a low-cost satellite data transceiver using a standard HUMSAT protocol. The transceiver is capable of receiving data from the HUMSAT constellation to remotely reconfigure sensors without the need of physically going to the sensor location. This transceiver uses a UHF channel around 437 MHz to exchange short data messages with the sensors. These data messages can contain up to 32 bytes of useful information and are transmitted at a speed around 300 bps. The protocol designed for this system handles the access to the channel by all these elements and guarantees a correct transmission of the information in such an scenario. The University of Vigo has launched the first satellite of the constellation, the HUMSAT-D CubeSat in November 2013 and has

the suitability of lime rice husk ash cement as construction material

African Journals Online (AJOL)

NIJOTECH

Enugu State University of Science and Technology, Enugu, Nigeria. ... It was therefore concluded that high percentage contents of silica, ... the Lime Rice Husk Ash cement when used as a construction material would depend ... thermal treatment of the silica in the husk .... test specimen in their moulds were stored in a.

BRITE-Constellation Science Operations

Science.gov (United States)

Kuschnig, R.

2017-09-01

BRITE-Constellation is a nanosatellite mission designed for stellar astrophysical research in collaboration between Austria, Canada and Poland. A fleet of six spacecrafts was funded, built and launched, two from each country, all designed to perform precise time-series photometry of the brightest stars in the sky. While the spacecrafts have the same basic design, three satellites host an instrument sensitive in a red bandpass, the others, for a blue wavelength range. From the six satellites launched, five are operational. The sixth one did not separate from the upper stage of the rocket and remains idle. The first pair, the Austrian satellites, started to collect science measurements with their wide field (˜24°) cameras in early December 2013. Since then, more than 340 stars were observed during 16 campaigns, the majority for more than 100 days (up to 168 days) continuously. In total, more than 2.1 million measurements have been collected so far. Originally, the limiting magnitude for target stars was set to \\mag(V)=4. However, even stars as faint as \\mag(V)=6.5 have been observed with sufficient precision. This is a review of science operations conducted during the past 3.5 years.

A mars communication constellation for human exploration and network science

Science.gov (United States)

Castellini, Francesco; Simonetto, Andrea; Martini, Roberto; Lavagna, Michèle

2010-01-01

This paper analyses the possibility of exploiting a small spacecrafts constellation around Mars to ensure a complete and continuous coverage of the planet, for the purpose of supporting future human and robotic operations and taking advantage of optical transmission techniques. The study foresees such a communications mission to be implemented at least after 2020 and a high data-rate requirement is imposed for the return of huge scientific data from massive robotic exploration or to allow video transmissions from a possible human outpost. In addition, the set-up of a communication constellation around Mars would give the opportunity of exploiting this multi-platform infrastructure to perform network science, that would largely increase our knowledge of the planet. The paper covers all technical aspects of a feasibility study performed for the primary communications mission. Results are presented for the system trade-offs, including communication architecture, constellation configuration and transfer strategy, and the mission analysis optimization, performed through the application of a multi-objective genetic algorithm to two models of increasing difficulty for the low-thrust trajectory definition. The resulting communication architecture is quite complex and includes six 530 kg spacecrafts on two different orbital planes, plus one redundant unit per plane, that ensure complete coverage of the planet’s surface; communications between the satellites and Earth are achieved through optical links, that allow lower mass and power consumption with respect to traditional radio-frequency technology, while inter-satellite links and spacecrafts-to-Mars connections are ensured by radio transmissions. The resulting data-rates for Earth-Mars uplink and downlink, satellite-to-satellite and satellite-to-surface are respectively 13.7 Mbps, 10.2 Mbps, 4.8 Mbps and 4.3 Mbps, in worst-case. Two electric propulsion modules are foreseen, to be placed on a C3˜0 escape orbit with two

Selective classification and quantification model of C&D waste from material resources consumed in residential building construction.

Science.gov (United States)

Mercader-Moyano, Pilar; Ramírez-de-Arellano-Agudo, Antonio

2013-05-01

The unfortunate economic situation involving Spain and the European Union is, among other factors, the result of intensive construction activity over recent years. The excessive consumption of natural resources, together with the impact caused by the uncontrolled dumping of untreated C&D waste in illegal landfills have caused environmental pollution and a deterioration of the landscape. The objective of this research was to generate a selective classification and quantification model of C&D waste based on the material resources consumed in the construction of residential buildings, either new or renovated, namely the Conventional Constructive Model (CCM). A practical example carried out on ten residential buildings in Seville, Spain, enabled the identification and quantification of the C&D waste generated in their construction and the origin of the waste, in terms of the building material from which it originated and its impact for every m(2) constructed. This model enables other researchers to establish comparisons between the various improvements proposed for the minimization of the environmental impact produced by building a CCM, new corrective measures to be proposed in future policies that regulate the production and management of C&D waste generated in construction from the design stage to the completion of the construction process, and the establishment of sustainable management for C&D waste and for the selection of materials for the construction on projected or renovated buildings.

Understanding Business Strategies of Networked Value Constellations Using Goal- and Value Modeling

NARCIS (Netherlands)

Gordijn, Jaap; Petit, Michael; Wieringa, Roelf J.

2006-01-01

In goal-oriented requirements engineering (GORE), one usually proceeds from a goal analysis to a requirements specification, usually of IT systems. In contrast, we consider the use of GORE for the design of IT-enabled value constellations, which are collections of enterprises that jointly satisfy a

Building new meanings in technical English from the perspective of the lexical constellation model

Directory of Open Access Journals (Sweden)

Camino Rea Rizzo

2010-10-01

Full Text Available The need to name and communicate to others new concepts in specific domains of human activity leads to the formation of new terms. However, many of the technical words in English are not new from the point of view of form. They rather derive from the common stock of general language: new lexical units are built from already existing forms and/or meanings. The original form is used for naming a new concept by adding a distinctive specialized lexical feature while keeping some semantic features of the original concept. In this paper, we aim at explaining and visualizing the nature of some of the processes that allow for the construction of new senses in technical words through a branching and expanding process, as explained in the lexical constellation model. The analysis is performed on three words widely used in telecommunication English: “bus”, “hub” and “chip”. The understanding of the process may be of great help for learners of ESP in general and technical English in particular.

The CEOS Atmospheric Composition Constellation: Enhancing the Value of Space-Based Observations

Science.gov (United States)

Eckman, Richard; Zehner, Claus; Al-Saadi, Jay

2015-01-01

The Committee on Earth Observation Satellites (CEOS) coordinates civil space-borne observations of the Earth. Participating agencies strive to enhance international coordination and data exchange and to optimize societal benefit. In recent years, CEOS has collaborated closely with the Group on Earth Observations (GEO) in implementing the Global Earth Observing System of Systems (GEOSS) space-based objectives. The goal of the CEOS Atmospheric Composition Constellation (ACC) is to collect and deliver data to improve monitoring, assessment and predictive capabilities for changes in the ozone layer, air quality and climate forcing associated with changes in the environment through coordination of existing and future international space assets. A project to coordinate and enhance the science value of a future constellation of geostationary sensors measuring parameters relevant to air quality supports the forthcoming European Sentinel-4, Korean GEMS, and US TEMPO missions. Recommendations have been developed for harmonization to mutually improve data quality and facilitate widespread use of the data products.

The interhemispheric and F region dynamo currents revisited with the Swarm constellation

DEFF Research Database (Denmark)

Luehr, Hermann; Kervalishvili, Guram; Michaelis, Ingo

2015-01-01

Based on magnetic field data sampled by the Swarm satellite constellation it is possible for the first time to determine uniquely F region currents at low latitudes. Initial results are presented from the first 200days of formation flight (17 April to 5 November 2014). Detailed results have been...

EOS Aqua: Mission Status at the Earth Science Constellation (ESC) Mission Operations Working Group (MOWG) Meeting at the Kennedy Space Center (KSC)

Science.gov (United States)

Guit, Bill

2017-01-01

This presentation at the Earth Science Constellation Mission Operations Working Group meeting at KSC in December 2017 to discuss EOS (Earth Observing System) Aqua Earth Science Constellation status. Reviewed and approved by Eric Moyer, ESMO (Earth Science Mission Operations) Deputy Project Manager.

Aspects of new material application for boilers construction; Aspekty wdrazania nowych materialow w budowie kotlow

Energy Technology Data Exchange (ETDEWEB)

Czerniawski, R. [RAFAKO S.A., Raciborz (Poland)

1996-12-31

Review of steel types commonly used for energetic boilers construction has been done. The worldwide trends in new materials application for improvement of boilers quality have been discussed. The mechanical properties of boiler construction steels have been shown and compared. 3 refs, 5 figs, 1 tab.

Assessment on the sustainable use of alternative construction materials as a substitute to natural aggregates

CSIR Research Space (South Africa)

George, Theresa B

2016-08-01

Full Text Available , and identifies potential construction materials such as glass, slags and recycled asphalt pavement (RAP) that are locally available as alternative aggregate materials to virgin aggregates. An economic cost analysis conducted indicated that it is more cost...

Determination of the long-term release of metal(loid)s from construction materials using DGTs.

Science.gov (United States)

Schmukat, A; Duester, L; Ecker, D; Heininger, P; Ternes, T A

2013-09-15

Long-term leaching experiments are crucial to estimate the potential release of dangerous substances from construction materials. The application of Diffuse Gradients in Thin film (DGT) in static-batch experiments was tested to study the long-term release of metal(loid)s from construction materials for hydraulic engineering, for half a year. Long-term release experiments are essential to improve calculations of the life-time release for this materials. DGTs in batch experiments were found to be a space and labour efficient application, which enabled (i) to study, in a non-invasive manner, the total release of nine metal(loid)s for half a year, (ii) to differentiate between release mechanisms and (iii) to study mechanisms which were contrary to the release or caused experimental artefacts in the batch experiments. For copper slag (test material) it was found that eight metal(loid)s were released over the whole time period of 184 d. Cu, Ni and Pb were found to be released, predominantly caused by (the) weathering of sulphide minerals. Only for Zn a surface depletion mechanism was identified. The results from the long-term batch experiments deliver new information on the release of metal(loid)s during the life cycle of construction materials with regard to river basin management objectives. Copyright © 2013 Elsevier B.V. All rights reserved.

Materials requirements for the ITER vacuum vessel and in-vessel components - approaching the construction phase

International Nuclear Information System (INIS)

Barabash, V.; Ioki, K.; Pick, M.; Girard, J.P.; Merola, M.

2007-01-01

Full text of publication follows: The ITER activities are fully devoted toward its construction. In accordance with the ITER integrated project schedule, the procurement specifications for the manufacturing of the Vacuum Vessel should be prepared by March 2008 and the procurement specifications for the in-vessel components (first wall/blanket, divertor) by 2009. To update the design, considering design and technology evolution, the ITER Design Review has been launched. Among the various topics being discussed are the important issues related to selection of materials, material procurement, and assessment of performance during operation. The main requirements related to materials for the vacuum vessel and the in-vessel components are summarized in the paper. The specific licensing requirements are to be followed for structural materials of pressure and nuclear pressure equipment components for construction of ITER. In addition, the procurements in ITER will be done mostly 'in-kind' and it is assumed that materials for these components will be produced by different Parties. However, in accordance with the regulatory requirements and quality requirements for operation, common specifications and the general rules to fulfill these requirements are to be adopted. For some ITER components (e.g. first wall, divertor high heat flux components), the ultimate qualification of the joining technologies (Be/Cu, SS/Cu, CFC/Cu, W/Cu) is under final evaluation. Successful accomplishment of the qualification program will allow to proceed with procurements of the components for ITER. The criteria for acceptance of these components and materials after manufacturing are described and the main results will be reported. Additional materials issues, which come from the on-going manufacturing R and D program, will be also described. Finally, further materials activity during the construction phase, needs for final qualification and acceptance of materials are discussed. (authors)

Marine dredged sediments as new materials resource for road construction.

Science.gov (United States)

Siham, Kamali; Fabrice, Bernard; Edine, Abriak Nor; Patrick, Degrugilliers

2008-01-01

Large volumes of sediments are dredged each year in Europe in order to maintain harbour activities. With the new European Union directives, harbour managers are encouraged to find environmentally sound solutions for these materials. This paper investigates the potential uses of Dunkirk marine dredged sediment as a new material resource for road building. The mineralogical composition of sediments is evaluated using X-ray diffraction and microscopy analysis. Since sediments contain a high amount of water, a dewatering treatment has been used. Different suitable mixtures, checking specific geotechnical criteria as required in French standards, are identified. The mixtures are then optimized for an economical reuse. The mechanical tests conducted on these mixtures are compaction, bearing capacity, compression and tensile tests. The experimental results show the feasibility of the beneficial use of Dunkirk marine dredged sand and sediments as a new material for the construction of foundation and base layers for roads. Further research is now needed to prove the resistance of this new material to various environmental impacts (e.g., frost damage).

Sheep Wool as a Construction Material for Energy Efficiency Improvement

Directory of Open Access Journals (Sweden)

Azra Korjenic

2015-06-01

Full Text Available The building sector is responsible for 40% of the current CO2 emissions as well as energy consumption. Sustainability and energy efficiency of buildings are currently being evaluated, not only based on thermal insulation qualities and energy demands, but also based on primary energy demand, CO2 reductions and the ecological properties of the materials used. Therefore, in order to make buildings as sustainable as possible, it is crucial to maximize the use of ecological materials. This study explores alternative usage of sheep wool as a construction material beyond its traditional application in the textile industry. Another goal of this research was to study the feasibility of replacement of commonly used thermal insulations with natural and renewable materials which have better environmental and primary energy values. Building physics, energy and environmental characteristics were evaluated and compared based on hygrothermal simulation and ecological balance methods. The observations demonstrate that sheep wool, compared with mineral wool and calcium silicate, provides comparable thermal insulation characteristics, and in some applications even reveals better performance.

Determining the Supply of Material Resources for High-Rise Construction: Scenario Approach

Science.gov (United States)

Minnullina, Anna; Vasiliev, Vladimir

2018-03-01

This article presents a multi-criteria approach to determining the supply of material resources for high-rise construction under certain and uncertain conditions, which enables integrating a number of existing models into a fairly compact generalised economic and mathematical model developed for two extreme scenarios.

Characterization of tissue-equivalent materials for use in construction of physical phantoms

International Nuclear Information System (INIS)

Souza, Edvan V. de; Oliveira, Alex C.H. de; Vieira, Jose W.; Lima, Fernando R.A.

2013-01-01

Phantoms are physical or computational models used to simulate the transport of ionizing radiation, their interactions with human body tissues and evaluate the deposition of energy. Depending on the application, you can build phantoms of various types and features. The physical phantoms are made of materials with behavior similar to human tissues exposed to ionizing radiation, the so-called tissue-equivalent materials. The characterization of various tissue-equivalent materials is important for the choice of materials to be used is appropriate, seeking a better cost-benefit ratio. The main objective of this work is to produce tables containing the main characteristics of tissue-equivalent materials. These tables were produced in Microsoft Office Excel. Among the main features of tissue-equivalent materials that were added to the tables, are density, chemical composition, physical state, chemical stability and solubility. The main importance of this work is to contribute to the construction of high-quality physical phantoms and avoid the waste of materials

Simulation studies to determine the gamma radiation dose due to natural radioactivity in construction materials in dwellings

International Nuclear Information System (INIS)

Shetty, P.G.; Chougaonkar, M.P.; Mayya, Y.S.; Puranik, V.D.

2008-01-01

Gamma radiation dose is imparted to the living due to the natural radionuclides present in the environmental materials, including the building materials used for construction of dwellings. The radionuclides responsible for natural radiation dose are the primordial radionuclides of 232 Th, 238 U series and the 40 K. These nuclides together with their daughters give rise to external gamma ray dose as well as the inhalation doses arising from the short-lived radon/thoron gases and their progenies that are exhaled from the walls of the construction materials. The radioactivity inside a room and the radiation dose caused by it mainly depends on the concentration of the above mentioned radionuclides in the building materials and type/properties like thickness, density etc. of the material used for construction. A computational model for a standard house (without windows and door) has been designed using Monte Carlo N-particle code (MCNP). The code works on probability theory. The present paper discusses the individual contribution of doses from 40 K, uranium and thorium series. Further variation in the gamma doses due to different building materials and densities are also discussed. (author)

Assessment of impact of construction materials on the ecological safety of home

Directory of Open Access Journals (Sweden)

Zhigulina Anna

2017-01-01

Full Text Available The article deals with the problems of creating environmentally friendly aerial environment within residential premises. The main sources causing air pollution of urban housing are determined and classified. The origins of air pollution sources of residential premises are adopted as the classifying criterion. The sources of contamination are defined and assessed. Particular attention is paid to the choice of environmentally friendly building materials. The methodology for assessing toxicity of industrial waste used in the production of housing materials is developed to assess the comfort and environmental safety of home. The idea of creating “Residential buldings ID” containing information on the construction materials used is introduced.

The distribution of common construction materials at risk to acid deposition in the United States

Science.gov (United States)

Lipfert, Frederick W.; Daum, Mary L.

Information on the geographic distribution of various types of exposed materials is required to estimate the economic costs of damage to construction materials from acid deposition. This paper focuses on the identification, evaluation and interpretation of data describing the distributions of exterior construction materials, primarily in the United States. This information could provide guidance on how data needed for future economic assessments might be acquired in the most cost-effective ways. Materials distribution surveys from 16 cities in the U.S. and Canada and five related databases from government agencies and trade organizations were examined. Data on residential buildings are more commonly available than on nonresidential buildings; little geographically resolved information on distributions of materials in infrastructure was found. Survey results generally agree with the appropriate ancillary databases, but the usefulness of the databases is often limited by their coarse spatial resolution. Information on those materials which are most sensitive to acid deposition is especially scarce. Since a comprehensive error analysis has never been performed on the data required for an economic assessment, it is not possible to specify the corresponding detailed requirements for data on the distributions of materials.

Determining the Environmental Benefits of Ultra High Performance Concrete as a Bridge Construction Material

Science.gov (United States)

Lande Larsen, Ingrid; Granseth Aasbakken, Ida; O'Born, Reyn; Vertes, Katalin; Terje Thorstensen, Rein

2017-10-01

Ultra High Performance Concrete (UHPC) is a material that is attracting attention in the construction industry due to the high mechanical strength and durability, leading to structures having low maintenance requirements. The production of UHPC, however, has generally higher environmental impact than normal strength concrete due to the increased demand of cement required in the concrete mix. What is still not sufficiently investigated, is if the longer lifetime, slimmer construction and lower maintenance requirements lead to a net environmental benefit compared to standard concrete bridge design. This study utilizes life cycle assessment (LCA) to determine the lifetime impacts of two comparable highway crossing footbridges spanning 40 meters, designed respectively with UHPC and normal strength concrete. The results of the study show that UHPC is an effective material for reducing lifetime emissions from construction and maintenance of long lasting infrastructure, as the UHPC design outperforms the normal strength concrete bridge in most impact categories.

Materials development and field demonstration of high-recycled-content concrete for energy-efficient building construction; FINAL

International Nuclear Information System (INIS)

Ostowari, Ken; Nosson, Ali

2000-01-01

The project developed high-recycled-content concrete material with balanced structural and thermal attributes for use in energy-efficient building construction. Recycled plastics, tire, wool, steel and concrete were used as replacement for coarse aggregates in concrete and masonry production. With recycled materials the specific heat and thermal conductivity of concrete could be tailored to enhance the energy-efficiency of concrete buildings. A comprehensive field project was implemented which confirmed the benefits of high-recycled-content concrete for energy-efficient building construction

Westward tilt of low-latitude plasma blobs as observed by the Swarm constellation

DEFF Research Database (Denmark)

Park, Jaeheung; Luehr, Hermann; Michaelis, Ingo

2015-01-01

In this study we investigate the three-dimensional structure of low-latitude plasma blobs using multi-instrument and multisatellite observations of the Swarm constellation. During the early commissioning phase the Swarm satellites were flying at the same altitude with zonal separation of about 0...

SCARF - The Swarm Satellite Constellation Application and Research Facility

DEFF Research Database (Denmark)

Olsen, Nils

2014-01-01

Swarm, a three-satellite constellation to study the dynamics of the Earth's magnetic field and its interactions with the Earth system, has been launched in November 2013. The objective of the Swarm mission is to provide the best ever survey of the geomagnetic field and its temporal evolution, which...... conductivity, thermospheric mass density and winds, field-aligned currents, an ionospheric plasma bubble index, the ionospheric total electron content and the dayside equatorial zonal electrical field will be calculated. This service is expected to be operational for a period of at least 5 years. The present...

Natural radioactivity in Slovak construction materials and the indoor dose rate from building materials

International Nuclear Information System (INIS)

Cabanekova, H.; Vladar, M.

1998-01-01

For keeping the population exposure al low as reasonably achievable (recommended by the Slovak regulations), the radioactive content of primordial radionuclides in building materials and products have not to exceed 370 Bq kg -1 of radium equivalent activity and 120 Bq kg -1 of 226 Ra. Samples of building materials (cement, stone, fly-ash, light concrete, slag, dross, sand dolomite. etc.) user for construction of the residential buildings were collected, milled and screened with 2-3 cm sieve. After drying, the samples were stored in 450 cm 3 sealed polyethylene containers for a 30 day period. All samples were measured in a 4 π geometry usually for 60,000 seconds. Measurements of 226 Ra, 232 Th and 40 K concentrations were carried out by high resolution gamma-ray spectrometry. The primordial radionuclides 226 and 232 Th were assessed through their progeny photo-peaks 214 Bi (609 keV), 214 Pb (295 keV, 351 keV) 228 Ac (338 keV, 911 keV) and 212 Pb (238 keV). The specific activity of both nuclides has been determined as weighted average of their photo-peaks. 40 K was measured directly via its 1460 keV peak. Until now, about 600 samples of building materials have been measured. The obtained radium equivalent activity in various types of building materials and mean annual effective doses of gamma radiation are presented. (J.K.)

What the Heliophysics System Observatory is teaching us about future constellations

Science.gov (United States)

Angelopoulos, V.

2017-12-01

Owing to the benign space weather during the recent solar cycle numerous Heliophysics missions have outlived their original purpose and have exceeded expectations in terms of science return. The simultaneous availability of several multi-spacecraft fleets also offers conjunction opportunities that compounds their science yield. It allows the Heliophysics System, a vast region of Sun-Earth interactions, to be peered through the colletive eyes of a fortuitous grand Observatory. The success of this Heliophysics/Geospace System Observatory (H/GSO) has been partly due to fuel resources available on THEMIS, allowing it to reconfigure its orbit lines of apsides, apogees and mean anomalies to optimize conjunctions with the rest of the H/GSO. The other part of the success has been a mandatory open data policy, the accessibility of the data though common data formats, unified analysis tools (e.g. SPEDAS) and distributed data repositories. Future constellations are motivated by the recent science lessons learned: Tight connections between dayside and nightside processes, evidenced by fortuitous conjunctions of ground and space-based assets, suggest that regional activations drive classical global modes of circulation. Like regional tornadoes and hurricanes synthesize global atmospheric weather that cannot be studied with 5 weather stations alone, one per continent, so do dayside reconnection, and nightside injections require more than a handful of point measurements. Like atmospheric weather, space weather too requires networks of stations built to meet a minimum set of requirements to "play together" and build on each other over time. Like Argo's >3000 buoys have revolutionized research, modeling and prediction by global circulation models, "space buoys" can study space weather fronts and double-up as monitors and inputs to space weather models, increasing fidelity and advance warning. Reconfigurability can allow versatility as the scientific targets adjust to the knowledge

Non-destructive study of new construction materials for advanced nuclear reactors

International Nuclear Information System (INIS)

Simeg Veternikova, J.; Slugen, V.; Sabelova, V.; Sojak, S.; Petriska, M.

2013-01-01

Microstructure of new construction steels for advanced reactor systems with different type of structure: oxide dispersion strengthened steel - ODS Eurofer (20% Cr), ferritic-martensitic steel Eurofer 97 and austenitic steel NF 709 were studied by positron annihilation lifetime spectroscopy. Samples were measured before and after helium ion implantation (He"+); therefore microstructure changes and radiation resistance to alpha particles of these steels were observed. Defect accumulation due to the radiation treatment was assumed in all investigated materials; therefore positron mean-lifetimes will increase up with notable change. The paper compares radiation damage of different type of structure and point out to the most radiation resistant structure/material from the investigated ones. (authors)

Tentative to use wastes from thermal power plants for construction building materials

Science.gov (United States)

Bui, Quoc-Bao; Phan, To-Anh-Vu; Tran, Minh-Tung; Le, Duc-Hien

2018-04-01

Thermal power plants (TPP) generates wastes (bottom and fly ashes) which become a serious environmental problem in Vietnam. Indeed, although in several countries fly ash can be used for cement industry, fly ash from actual TPP in Vietnam does not have enough good quality for cement production, because the fly ash treatment phase has not yet included in the generations of existing Vietnamese TPP. That is why bottom ash and fly ash purely become wastes and their evacuation is an urgent demand of the society. This paper presents an investigation using fly and bottom ashes in the manufacturing of construction materials. The main aims of this study is to reduce environmental impacts of fly and bottom ashes, and to test another non-conventional binder to replace cement in the manufacture of unburnt bricks. Several proportions of fly ash, bottom ash, cement, gravel, sand and water were tested to manufacture concretes. Then, geopolymer was prepared from the fly ash and an activator. Specimens were tested in uniaxial compressions. Results showed that the cement concrete tested had the compressive strengths which could be used for low rise constructions and the material using geopolymer could be used for non-load-bearing materials (unburnt bricks).

New Experiences in Dike Construction with Soil-Ash Composites and Fine-Grained Dredged Materials

Directory of Open Access Journals (Sweden)

Duszyński Remigiusz

2017-12-01

Full Text Available The supporting structure inside a coastal dike is often made of dredged non-uniform sand with good compaction properties. Due to the shortage of natural construction material for both coastal and river dikes and the surplus of different processed materials, new experiments were made with sand-ash mixtures and fine-grained dredged materials to replace both dike core and dike cover materials resulting in economical, environmentally friendly and sustainable dikes. Ash from EC Gdańsk and dredged sand from the Vistula river were mixed to form an engineering material used for dike construction. The optimum sand-ash composites were applied at a field test site to build a large-scale research dike. Fine-grained dredged materials from Germany were chosen to be applied in a second full-scale research dike in Rostock. All materials were investigated according to the standards for soil mechanical analysis. This includes basic soil properties, mechanical characteristics, such as grain-size distribution, compaction parameters, compressibility, shear strength, and water permeability. In the field, the infiltration of water into the dike body as well as the erosion resistance of the cover material against overflowing water was determined. Results of both laboratory and field testing are discussed in this paper. In conclusion, the mixing of bottom ash with mineral soil, such as relatively uniform dredged sand, fairly improves the geotechnical parameters of the composite, compared to the constituents. Depending on the composite, the materials may be suitable to build a dike core or an erosion-resistant dike cover.

New Experiences in Dike Construction with Soil-Ash Composites and Fine-Grained Dredged Materials

Science.gov (United States)

Duszyński, Remigiusz; Duszyńska, Angelika; Cantré, Stefan

2017-12-01

The supporting structure inside a coastal dike is often made of dredged non-uniform sand with good compaction properties. Due to the shortage of natural construction material for both coastal and river dikes and the surplus of different processed materials, new experiments were made with sand-ash mixtures and fine-grained dredged materials to replace both dike core and dike cover materials resulting in economical, environmentally friendly and sustainable dikes. Ash from EC Gdańsk and dredged sand from the Vistula river were mixed to form an engineering material used for dike construction. The optimum sand-ash composites were applied at a field test site to build a large-scale research dike. Fine-grained dredged materials from Germany were chosen to be applied in a second full-scale research dike in Rostock. All materials were investigated according to the standards for soil mechanical analysis. This includes basic soil properties, mechanical characteristics, such as grain-size distribution, compaction parameters, compressibility, shear strength, and water permeability. In the field, the infiltration of water into the dike body as well as the erosion resistance of the cover material against overflowing water was determined. Results of both laboratory and field testing are discussed in this paper. In conclusion, the mixing of bottom ash with mineral soil, such as relatively uniform dredged sand, fairly improves the geotechnical parameters of the composite, compared to the constituents. Depending on the composite, the materials may be suitable to build a dike core or an erosion-resistant dike cover.

A Construction System for CALL Materials from TV News with Captions

Science.gov (United States)

Kobayashi, Satoshi; Tanaka, Takashi; Mori, Kazumasa; Nakagawa, Seiichi

Many language learning materials have been published. In language learning, although repetition training is obviously necessary, it is difficult to maintain the learner's interest/motivation using existing learning materials, because those materials are limited in their scope and contents. In addition, we doubt whether the speech sounds used in most materials are natural in various situations. Nowadays, some TV news programs (CNN, ABC, PBS, NHK, etc.) have closed/open captions corresponding to the announcer's speech. We have developed a system that makes Computer Assisted Language Learning (CALL) materials for both English learning by Japanese and Japanese learning by foreign students from such captioned newscasts. This system computes the synchronization between captions and speech by using HMMs and a forced alignment algorithm. Materials made by the system have following functions: full/partial text caption display, repetition listening, consulting an electronic dictionary, display of the user's/announcer's sound waveform and pitch contour, and automatic construction of a dictation test. Materials have following advantages: materials present polite and natural speech, various and timely topics. Furthermore, the materials have the following possibility: automatic creation of listening/understanding tests, and storage/retrieval of the many materials. In this paper, firstly, we present the organization of the system. Then, we describe results of questionnaires on trial use of the materials. As the result, we got enough accuracy on the synchronization between captions and speech. Speaking totally, we encouraged to research this system.

Developing improved opportunities for the recycling and reuse of materials in road, bridge, and construction projects.

Science.gov (United States)

2014-12-01

The use of recycled and reused materials in transportation construction reduces consumption of non-renewable : resources. The objective of this research was to develop opportunities for improving the recycling and reuse of : materials in road and bri...

Effect of interface of electronics devices constructed with different materials to X-ray

International Nuclear Information System (INIS)

Mu Weibing; Chen Panxun

2003-01-01

The behavior of X-ray nearby interface which is constructed with different materials is introduced in this paper. And the affect to electronics devices of this behavior is analyzed, the affect factors of four interfaces are calculated by Monte-Carlo method

Constructing a large variety of Dirac-cone materials in the Bi(1-x)Sb(x) thin film system.

Science.gov (United States)

Tang, Shuang; Dresselhaus, Mildred S

2012-12-21

We theoretically predict that a large variety of Dirac-cone materials can be constructed in Bi(1-x)Sb(x) thin films and we here show how to construct single-, bi- and tri-Dirac-cone materials with various amounts of wave vector anisotropy. These different types of Dirac cones can be of special interest to electronic device design, quantum electrodynamics and other fields.

TFTR materials issues and problems during design and construction

International Nuclear Information System (INIS)

Sabado, M.; Little, R.

1984-01-01

TFTR as well as its contemporaries, T15, JT60, and JET, have important contributions to make towards our understanding of plasma conditions in the thermonuclear regime. One of the main objectives of TFTR is to produce fusion power densities approaching those in a fusion reactor, approx.= 1 Wcm -3 at Q approx.= 1-2. TFTR will be the first tokamak to routinely use deuterium tritium, and produce approx.= 10 19 fusion neutrons per pulse. With startup of TFTR on December 24, 1982, the demonstration of physics feasibility of 'breakeven' is close at hand. Since TFTR performance will be reactor relevant, the capability of materials/components to withstand the hostile effects of a plasma environment will be presented. It is intended that designers of future fusion devices benefit from the materials technology developments and applications on TFTR. In an attempt to comply with this mandate, this paper will describe TFTR issues on materials, their developments, selections, problems, and solutions. Special emphasis will be given, in particular, to the impurity control devices in TFTR, namely, the limiter and surface pumping system located inside the vacuum vessel. The plasma will interact with these components and they will be subjected to disruptions, a vacuum of 10 -6 to 10 -8 torr and a nominal temperatures of 0 C. 'Painful' materials development problems encountered will be reviewed, as well as important 'lessons learned'. A briefing on the materials of construction will be given, with some comments on the problems that developed and their solutions. (orig.)

3D printing for construction: a procedural and material-based approach

Directory of Open Access Journals (Sweden)

A. Nadal

2017-06-01

Full Text Available 3D printing for construction is stagnated at an early stage of development, especially regarding material optimization and procedural issues. These limitations are due to the specific knowledge that these technologies imply, the total cost of the machinery involved, and the lack of clear procedural guidelines. This paper presents a methodology that aims at overcoming these limitations through a workflow that allows for the ease of use of 6-axis robotic arms. A technique for the optimization of material usage is presented. A test case that shows the integration the design-to-fabrication process combining Integrated Robotic Systems (IRS and Additive Layer Manufacturing (ALM techniques is discussed. A structure-based approach to material optimization and smart infill patterning is introduced. A 0.4 x 0.4 x 1.5 m test part is shown as technological demonstrator.

Titanium oxo-clusters: precursors for a Lego-like construction of nanostructured hybrid materials.

Science.gov (United States)

Rozes, Laurence; Sanchez, Clément

2011-02-01

Titanium oxo-clusters, well-defined monodispersed nano-objects, are appropriate nano-building blocks for the preparation of organic-inorganic materials by a bottom up approach. This critical review proposes to present the different structures of titanium oxo-clusters referenced in the literature and the different strategies followed to build up hybrid materials with these versatile building units. In particular, this critical review cites and reports on the most important papers in the literature, concentrating on recent developments in the field of synthesis, characterization, and the use of titanium oxo-clusters for the construction of advanced hybrid materials (137 references).

Numerical and Experimental Analysis on Inorganic Phase Change Material Usage in Construction

Science.gov (United States)

Muthuvel, S.; Saravanasankar, S.; Sudhakarapandian, R.; Muthukannan, M.

2014-12-01

This work demonstrates the significance of Phase Change Material (PCM) in the construction of working sheds and product storage magazines in fireworks industries to maintain less temperature variation by passive cooling. The inorganic PCM, namely Calcium Chloride Hexahydrate (CCH) is selected in this study. First, the performance of two models with inbuilt CCH was analysed, using computational fluid dynamics. A significant change in the variation of inner wall temperature was observed, particularly during the working hours. This is mainly due to passive cooling, where the heat transfer from the surroundings to the room is partially used for the phase change from solid to liquid. The experiment was carried out by constructing two models, one with PCM packed in hollow brick walls and roof, and the other one as a conventional construction. The experimental results show that the temperature of the room got significantly reduced up to 7 °C. The experimental analysis results had good agreement with the numerical analysis results, and this reveals the advantage of the PCM in the fireworks industry construction.

The Role of Cloud and Precipitation Radars in Convoys and Constellations

Science.gov (United States)

Tanelli, Simone; Durden, Stephen L.; Im, Eastwood; Sadowy, Gregory A.

2013-01-01

We provide an overview of which benefits a radar, and only a radar, can provide to any constellation of satellites monitoring Earth's atmosphere; which aspects instead are most useful to complement a radar instrument to provide accurate and complete description of the state of the troposphere; and finally which goals can be given a lower priority assuming that other types of sensors will be flying in formation with a radar.

NASA Materials Research for Extreme Conditions

Science.gov (United States)

Sharpe, R. J.; Wright, M. D.

2009-01-01

This Technical Memorandum briefly covers various innovations in materials science and development throughout the course of the American Space program. It details each innovation s discovery and development, explains its significance, and describes the applications of this material either in the time period discovered or today. Topics of research include silazane polymers, solvent-resistant elastomeric polymers (polyurethanes and polyisocyanurates), siloxanes, the Space Shuttle thermal protection system, phenolic-impregnated carbon ablator, and carbon nanotubes. Significance of these developments includes the Space Shuttle, Apollo programs, and the Constellation program.

New Construction and Catalyst Support Materials for Water Electrolysis at Elevated Temperatures

DEFF Research Database (Denmark)

Nikiforov, Aleksey

4 reports results of testing dierent types of commercially available stainless steels, Ni-based alloys as well as titanium and tantalum as possible metallic bipolar plates and construction materials for HTPEMEC. The corrosion resistance was measured under simulated conditions of high temperature PEM...... steam electrolyzer. Steady-state voltammetry was used in combination with scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX) to evaluate the stability of the mentioned materials. It was found that stainless steels were the least resistant to corrosion under strong anodic...... stainless steel showed outstanding resistance to corrosion in selected media, while passivation of titanium was weak, and the highest rate of corrosion among all tested materials was observed for titanium at 120 °C. Today, there is a high interest in the eld towards investigation of new catalyst materials...

Study of capability of microorganisms to develop on construction materials used in space objects

Science.gov (United States)

Rakova, N.; Svistunova, Y.; Novikova, N.

One of the most topical issues nowadays in the whole set of space research is the study of microbiological risks (medical, technical, technological). Experiments held onboard MIR station and International Space Station (ISS) clearly demonstrated capacity of microorganisms to contaminate the environment, equipment and belonging of habitual compartments of space objects. In this connection microorganisms-biodestructors play an important role. In their vital functioning they are capable of causing biological damage of different polymers, biocorrosion of metals which can lead to serious difficulties in performing long-term flights, namely the planned mission to Mars. Our purpose was to study capability of growth and reproduction of microorganisms on construction materials of various chemical composition as the first stage of biodestruction process. In our research we used "flight" strains of bacteria (Bacillus subtilus, Staphylococcus epidermidis, Staphylococcus saprophyticus, Pseudomonas pumilus etc.) recovered from the ISS environment in several missions. For control we used "earth" bacteria species with typical properties. To model the environment of the ISS we took construction materials which are widely used in the interior and equipment of the ISS. The results we've obtained show that some microorganisms are capable of living and reproducing themselves on construction materials and their capability is more pronounced than that of the "earth" species. The best capability for growth and reproduction was characteristic of Bacillus subtilus.

The DUBAISAT-2/DEIMOS-2 constellation: public-private cooperation between Emirates and Spain

Science.gov (United States)

Pirondini, Fabrizio; Al Marri, Salem

2014-10-01

The Emirates Institution for Advanced Science and Technology (EIAST) was established by the Dubai Government in 2006 with the goal of promoting a culture of advanced scientific research and technology innovation in Dubai and the UAE, and enhancing technology innovation and scientific skills among UAE nationals. EIAST launched in November 2013 the DubaiSat-2, its second Earth Observation satellite, and the first to provide VHR multispectral imagery. The satellite has successfully completed its in-orbit commissioning and it is now fully operational. ELECNOR DEIMOS is a private Spanish company, part of the Elecnor industrial group, which owns and operates DEIMOS-1, the first Spanish Earth Observation satellite, launched in 2009. ELECNOR DEIMOS launched in June 2014 its second satellite, DEIMOS-2, a VHR, agile satellite capable of providing 4-bands multispectral imagery. The whole end-to-end DEIMOS- 2 system has been designed to provide a cost-effective and highly responsive service to cope with the increasing need of fast access to VHR imagery. The two satellites, with a mass of 300 kg each, were developed in cooperation with Satrec-I (South Korea), and are based on the SpaceEye-1 platform. The two satellites have an identical payload, and produce 75- cm resolution pan-sharpened imagery across a 12-km swath. Together, they have a combined collection capacity of more than 300,000 sqkm per day. EIAST and ELECNOR DEIMOS have set up a unique, trans-national public-private partnership to operate the two satellites as a constellation, jointly commercialize the imagery of both satellites, and interchange technical and operational information to increase the efficiency of both systems. The operations of the constellation are based on four ground stations: Al Khawaneej (Dubai), Puertollano (Spain), Kiruna (Sweden) and Inuvik (Canada), which assure at least a contact per orbit with each satellite. The constellation functionalities of the ground segment were developed by EIAST

Dosimetry of radium equivalent in construction material of brick works in Sao Jose do Sabugi City - Paraiba, Brazil

International Nuclear Information System (INIS)

Araujo, Eduardo Eudes Nobrega de; Santos Junior, Jose Araujo dos; Amaral, Romilton dos Santos; Santos, Josineide Marques do Nascimento; Spacov, Isabel Cristina Guerra; Fernandez, Zahily Herrero

2015-01-01

The earth's crust has in its composition the Naturally Occurring Radioactive Material (NORM) that may have increased concentration due to activities of exploration and extraction of environmental resources. The civil construction is an economic activity that requires the use of much of the natural resources, such as the raw material of brick works, like clays, mainly used for the production of bricks and tiles. These construction materials may contain high levels of natural radioactive elements, even with concentrations higher than the limits established, given that the levels vary according to the composition of rocks and soil, due to the geological formation and may result in increased exposure of humans to natural radioactive activities. In this context, the radioecological dosimetry is defined in terms of Radium Equivalent activity (Ra eq ), that ensure radiometric conditions for the use of material derived from clays before its final application in housing construction, an initiative that ensures the radioecological safety of population. Thus, this study aimed to establish the calculation of Ra eq in the raw material of brick works located in Sao Jose do Sabugi city, state of Paraiba, in an area adjacent to the uranium deposits of Espinharas, to estimate the risks associated with primordial radionuclides attributed to TENORM activities (Technologically Enhanced Naturally Occurring Radioactive Materials) from the extraction and use of clay as a raw material in the manufacture of bricks and tiles. Analyses were performed by High Resolution Gamma Spectrometry, with HPGe-Be detector, assuming the state of secular radioactive equilibrium. The results ranged from 183.2 to 747.78 Bq/kg, with an average of 494.6 Bq/kg which exceeded the limit of 370 Bq/kg established by UNSCEAR for construction materials. Some samples obtained values exceeded by up the double this limit, suggesting control and radiometric certification for application of this material. (author)

Dosimetry of radium equivalent in construction material of brick works in Sao Jose do Sabugi City - Paraiba, Brazil

Energy Technology Data Exchange (ETDEWEB)

Araujo, Eduardo Eudes Nobrega de; Santos Junior, Jose Araujo dos; Amaral, Romilton dos Santos; Santos, Josineide Marques do Nascimento; Spacov, Isabel Cristina Guerra; Fernandez, Zahily Herrero, E-mail: eduardo.eudes@ufpe.br, E-mail: jaraujo@ufpe.br, E-mail: romilton@ufpe.br, E-mail: neideden@hotmail.com, E-mail: isabelspacov@gmail.com, E-mail: zahily1985@gmail.com [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Departamento de Energia Nuclear. Grupo de Radioecologia

2015-07-01

The earth's crust has in its composition the Naturally Occurring Radioactive Material (NORM) that may have increased concentration due to activities of exploration and extraction of environmental resources. The civil construction is an economic activity that requires the use of much of the natural resources, such as the raw material of brick works, like clays, mainly used for the production of bricks and tiles. These construction materials may contain high levels of natural radioactive elements, even with concentrations higher than the limits established, given that the levels vary according to the composition of rocks and soil, due to the geological formation and may result in increased exposure of humans to natural radioactive activities. In this context, the radioecological dosimetry is defined in terms of Radium Equivalent activity (Ra{sub eq}), that ensure radiometric conditions for the use of material derived from clays before its final application in housing construction, an initiative that ensures the radioecological safety of population. Thus, this study aimed to establish the calculation of Ra{sub eq} in the raw material of brick works located in Sao Jose do Sabugi city, state of Paraiba, in an area adjacent to the uranium deposits of Espinharas, to estimate the risks associated with primordial radionuclides attributed to TENORM activities (Technologically Enhanced Naturally Occurring Radioactive Materials) from the extraction and use of clay as a raw material in the manufacture of bricks and tiles. Analyses were performed by High Resolution Gamma Spectrometry, with HPGe-Be detector, assuming the state of secular radioactive equilibrium. The results ranged from 183.2 to 747.78 Bq/kg, with an average of 494.6 Bq/kg which exceeded the limit of 370 Bq/kg established by UNSCEAR for construction materials. Some samples obtained values exceeded by up the double this limit, suggesting control and radiometric certification for application of this material

A Constellation of CubeSat InSAR Sensors for Rapid-Revisit Surface Deformation Studies

Science.gov (United States)

Wye, L.; Lee, S.; Yun, S. H.; Zebker, H. A.; Stock, J. D.; Wicks, C. W., Jr.; Doe, R.

2016-12-01

The 2007 NRC Decadal Survey for Earth Sciences highlights three major Earth surface deformation themes: 1) solid-earth hazards and dynamics; 2) human health and security; and 3) land-use change, ecosystem dynamics and biodiversity. Space-based interferometric synthetic aperture radar (InSAR) is a key change detection tool for addressing these themes. Here, we describe the mission and radar payload design for a constellation of S-band InSAR sensors specifically designed to provide the global, high temporal resolution, sub-cm level deformation accuracy needed to address some of the major Earth system goals. InSAR observations with high temporal resolution are needed to properly monitor certain nonlinearly time-varying features (e.g., unstable volcanoes, active fault lines, and heavily-used groundwater or hydrocarbon reservoirs). Good temporal coverage is also needed to reduce atmospheric artifacts by allowing multiple acquisitions to be averaged together, since each individual SAR measurement is corrupted by up to several cm of atmospheric noise. A single InSAR platform is limited in how often it can observe a given scene without sacrificing global spatial coverage. Multiple InSAR platforms provide the spatial-temporal flexibility required to maximize the science return. However, building and launching multiple InSAR platforms is cost-prohibitive for traditional satellites. SRI International (SRI) and our collaborators are working to exploit developments in nanosatellite technology, in particular the emergence of the CubeSat standard, to provide high-cadence InSAR capabilities in an affordable package. The CubeSat Imaging Radar for Earth Science (CIRES) subsystem, a prototype SAR elec­tronics package developed by SRI with support from a 2014 NASA ESTO ACT award, is specifically scaled to be a drop-in radar solution for resource-limited delivery systems like CubeSats and small airborne vehicles. Here, we present our mission concept and flow-down requirements for a

Construction projects using alternative materials: a framework to assess their sustainability.

OpenAIRE

Fevre-Gautier , Anne-Lise; Beylot , Antoine; Vaxelaire , Stéphane; Michel , Pascale; Brullot , Sabrina; Lannou , Grégory; Stoos , Marion

2012-01-01

The increasing use of alternative materials and local solutions for construction projects raises questions about success conditions and criteria for the economic feasibility and global sustainability of such projects. Among others, how can design conditions - especially regarding the decision process - determine their success? We will present the results of a two-years project conducted from February 2010 to March 2012 in collaboration with ADEME (French agency of environment and energy contr...

Materials Design and System Construction for Conventional and New?Concept Supercapacitors

OpenAIRE

Wu, Zhong; Li, Lin; Yan, Jun?min; Zhang, Xin?bo

2017-01-01

With the development of renewable energy and electrified transportation, electrochemical energy storage will be more urgent in the future. Supercapacitors have received extensive attention due to their high power density, fast charge and discharge rates, and long?term cycling stability. During past five years, supercapacitors have been boomed benefited from the development of nanostructured materials synthesis and the promoted innovation of devices construction. In this review, we have summar...

The Swarm Satellite Constellation Application and Research Facility (SCARF) and Swarm data products

DEFF Research Database (Denmark)

Olsen, Nils; Friis-Christensen, Eigil; Floberghagen, R.

2013-01-01

Swarm, a three-satellite constellation to study the dynamics of the Earth's magnetic field and its interactions with the Earth system, is expected to be launched in late 2013. The objective of the Swarm mission is to provide the best ever survey of the geomagnetic field and its temporal evolution...

Composite Materials for Low-Temperature Applications

Science.gov (United States)

2008-01-01

Composite materials with improved thermal conductivity and good mechanical strength properties should allow for the design and construction of more thermally efficient components (such as pipes and valves) for use in fluid-processing systems. These materials should have wide application in any number of systems, including ground support equipment (GSE), lunar systems, and flight hardware that need reduced heat transfer. Researchers from the Polymer Science and Technology Laboratory and the Cryogenics Laboratory at Kennedy Space Center were able to develop a new series of composite materials that can meet NASA's needs for lightweight materials/composites for use in fluid systems and also expand the plastic-additive markets. With respect to thermal conductivity and physical properties, these materials are excellent alternatives to prior composite materials and can be used in the aerospace, automotive, military, electronics, food-packaging, and textile markets. One specific application of the polymeric composition is for use in tanks, pipes, valves, structural supports, and components for hot or cold fluid-processing systems where heat flow through materials is a problem to be avoided. These materials can also substitute for metals in cryogenic and other low-temperature applications. These organic/inorganic polymeric composite materials were invented with significant reduction in heat transfer properties. Decreases of 20 to 50 percent in thermal conductivity versus that of the unmodified polymer matrix were measured. These novel composite materials also maintain mechanical properties of the unmodified polymer matrix. These composite materials consist of an inorganic additive combined with a thermoplastic polymer material. The intrinsic, low thermal conductivity of the additive is imparted into the thermoplastic, resulting in a significant reduction in heat transfer over that of the base polymer itself, yet maintaining most of the polymer's original properties. Normal

Research into Behaviour Patterns Typical for Consumers of Construction Material as the Mission of Ecological Management

Directory of Open Access Journals (Sweden)

Ivanova Zinaida

2016-01-01

Full Text Available The objective of the co-authors is to study the motivation of purchasers of construction/finishing materials and the criteria that govern their selection. No systemic studies of consumer behavioral models and stereotypes in respect of residential housing have been performed so far. However, the environmentally determined management techniques, applicable to the production of building materials and construction of residential housing, are highly relevant both worldwide and in the Russian Federation. The co-authors have developed an original research methodology, drafted a questionnaire, and conducted a pilot survey. Its findings have proven that the price and quality of construction materials are the main factors that influence the decision making process in favor of particular items. Mere 14% of the respondents chose environmental friendliness as the decision making criterion. The findings of the focus group projects have also proven the trustworthiness of the stereotypes and behavioral models identified by the co-authors. The co-authors make a conclusion that further sociological surveys are needed to implement the patterns of environmentally determined management and to influence the value paradigms of the population.

Preparation and properties of hybrid materials for high-rise constructions

Directory of Open Access Journals (Sweden)

Matseevich Tatyana

2018-01-01

Full Text Available The theme of the research is important because it allows to use hybrid materials as finishing in the high-rise constructions. The aim of the study was the development of producing coloured hybrid materials based on liquid glass, a polyisocyanate, epoxy resin and 2.4-toluylenediisocyanate. The detailed study of the process of stress relaxation at different temperatures in the range of 20-100°C was provided. The study found that the obtained materials are subject to the simplified technology. The materials easy to turn different colors, and dyes (e.g. Sudan blue G are the catalysts for the curing process of the polymeric precursors. The materials have improved mechanical relaxation properties, possess different color and presentable, can be easily combined with inorganic base (concrete, metal. The limit of compressive strength varies from 32 to 17.5 MPa at a temperature of 20 to 100°C. The values σ∞ are from 20.4 to 7.7 MPa within the temperature range from 20 to 100°C. The physical parameters of materials were evaluated basing on the data of stress relaxation: the initial stress σ0, which occurs at the end of the deformation to a predetermined value; quasi-equilibrium stress σ∞, which persists for a long time relaxation process. Obtained master curves provide prediction relaxation behavior for large durations of relaxation. The study obtained new results. So, the addition of epoxy resin in the composition of the precursor improves the properties of hybrid materials. By the method of IR spectroscopy identified chemical transformations in the course of obtaining the hybrid material. Evaluated mechanical performance of these materials is long-time. Applied modern physically-based memory functions, which perfectly describe the stress relaxation process.

Preparation and properties of hybrid materials for high-rise constructions

Science.gov (United States)

Matseevich, Tatyana

2018-03-01

The theme of the research is important because it allows to use hybrid materials as finishing in the high-rise constructions. The aim of the study was the development of producing coloured hybrid materials based on liquid glass, a polyisocyanate, epoxy resin and 2.4-toluylenediisocyanate. The detailed study of the process of stress relaxation at different temperatures in the range of 20-100°C was provided. The study found that the obtained materials are subject to the simplified technology. The materials easy to turn different colors, and dyes (e.g. Sudan blue G) are the catalysts for the curing process of the polymeric precursors. The materials have improved mechanical relaxation properties, possess different color and presentable, can be easily combined with inorganic base (concrete, metal). The limit of compressive strength varies from 32 to 17.5 MPa at a temperature of 20 to 100°C. The values σ∞ are from 20.4 to 7.7 MPa within the temperature range from 20 to 100°C. The physical parameters of materials were evaluated basing on the data of stress relaxation: the initial stress σ0, which occurs at the end of the deformation to a predetermined value; quasi-equilibrium stress σ∞, which persists for a long time relaxation process. Obtained master curves provide prediction relaxation behavior for large durations of relaxation. The study obtained new results. So, the addition of epoxy resin in the composition of the precursor improves the properties of hybrid materials. By the method of IR spectroscopy identified chemical transformations in the course of obtaining the hybrid material. Evaluated mechanical performance of these materials is long-time. Applied modern physically-based memory functions, which perfectly describe the stress relaxation process.

Review of the proposed materials of construction for the SBWR and AP600 advanced reactors

International Nuclear Information System (INIS)

Diercks, D.R.; Shack, W.J.; Chung, H.M.; Kassner, T.F.

1994-06-01

Two advanced light water reactor (LWR) concepts, namely the General Electric Simplified Boiling Water Reactor (SBWR) and the Westinghouse Advanced Passive 600 MWe Reactor (AP600), were reviewed in detail by Argonne National Laboratory. The objectives of these reviews were to (a) evaluate proposed advanced-reactor designs and the materials of construction for the safety systems, (b) identify all aging and environmentally related degradation mechanisms for the materials of construction, and (c) evaluate from the safety viewpoint the suitability of the proposed materials for the design application. Safety-related systems selected for review for these two LWRs included (a) reactor pressure vessel, (b) control rod drive system and reactor internals, (c) coolant pressure boundary, (d) engineered safety systems, (e) steam generators (AP600 only), (f) turbines, and (g) fuel storage and handling system. In addition, the use of cobalt-based alloys in these plants was reviewed. The selected materials for both reactors were generally sound, and no major selection errors were found. It was apparent that considerable thought had been given to the materials selection process, making use of lessons learned from previous LWR experience. The review resulted in the suggestion of alternate an possibly better materials choices in a number of cases, and several potential problem areas have been cited

Economic impact of using nonmetallic materials in low to intermediate temperature geothermal well construction

Energy Technology Data Exchange (ETDEWEB)

1979-12-01

Four appendices are included. The first covers applications of low-temperature geothermal energy including industrial processes, agricultural and related processes, district heating and cooling, and miscellaneous. The second discusses hydrogeologic factors affecting the design and construction of low-temperature geothermal wells: water quality, withdrawal rate, water depth, water temperature, basic well designs, and hydrogeologic provinces. In the third appendix, properties of metallic and nonmetallic materials are described, including: specific gravity, mechanical strength properties, resistance to physical and biological attack, thermal properties of nonmetallics, fluid flow characteristics, corrosion resistance, scaling resistance, weathering resistance of nonmetallics, and hydrolysis resistance of nonmetallics. Finally, special considerations in the design and construction of low-temperature geothermal wells using nonmetallics materials are covered. These include; drilling methods, joining methods, methods of casing and screen installation, well cementing, and well development. (MHR)

A comparative toxicity assessment of materials used in aquatic construction.

Science.gov (United States)

Lalonde, Benoit A; Ernst, William; Julien, Gary; Jackman, Paula; Doe, Ken; Schaefer, Rebecca

2011-10-01

Comparative toxicity testing was performed on selected materials that may be used in aquatic construction projects. The tests were conducted on the following materials: (1) untreated wood species (hemlock [Tsuga ssp], Western red cedar (Thuja plicata), red oak [Quercus rubra], Douglas fir [Pseudotsuga menziesii], red pine [Pinus resinosa], and tamarack [Larix ssp]); (2) plastic wood; (3) Ecothermo wood hemlock stakes treated with preservatives (e.g., chromated copper arsenate [CCA], creosote, alkaline copper quaternary [ACQ], zinc naphthenate, copper naphthenate, and Lifetime Wood Treatment); (4) epoxy-coated steel; (5) hot-rolled steel; (6) zinc-coated steel; and (7) concrete. Those materials were used in acute lethality tests with rainbow trout, Daphnia magna, Vibrio fischeri and threespine stickleback. The results indicated the following general ranking of the materials (from the lowest to highest LC(50) values); ACQ > creosote > zinc naphthenate > copper naphthenate > CCA (treated at 22.4 kg/m(3)) > concrete > red pine > western red cedar > red oak > zinc-coated steel > epoxy-coated steel > CCA (6.4 kg/m(3)). Furthermore, the toxicity results indicated that plastic wood, certain untreated wood species (hemlock, tamarack, Douglas fir, and red oak), hot-rolled steel, Ecothermo wood, and wood treated with Lifetime Wood Treatment were generally nontoxic to the test species. © Springer Science+Business Media, LLC 2011

Fluxgate Magnetometry on the Experimental Albertan Satellite #1 (Ex-Alta-1) CubeSat Mission: Steps Toward a Magnetospheric Constellation Mission

Science.gov (United States)

Mann, I. R.; Miles, D.; Nokes, C.; Cupido, C.; Elliott, D.; Ciurzynski, M.; Barona, D.; Narod, B. B.; Bennest, J.; Pakhotin, I.; Kale, A.; Bruner, B.; Haluza-DeLay, T.; Forsyth, C.; Rae, J.; Lange, C.; Sameoto, D.; Milling, D. K.

2017-12-01

Making low noise magnetic measurements is a significant challenge to the use of cube-satellite (CubeSat) platforms for scientific constellation class missions for studies of geospace. We describe the design, validation, and test, and initial on-orbit results from a miniature, low-mass, low-power, and low-magnetic noise boom-mounted fluxgate magnetometer flown on the University of Alberta Experimental Albertan Satellite #1 (Ex-Alta-1) Cube Satellite, launched in 2017 from the International Space Station as part of the QB50 constellation mission. The miniature instrument achieves a magnetic noise floor of 150-200 pT/√Hz at 1 Hz, consumes 400 mW of power, has a mass of 121 g (sensor and boom), stows on the hull, and deploys on a 60 cm boom from a three-unit CubeSat reducing the noise from the onboard reaction wheel to less than 1.5 nT at the sensor. The instrument's capabilities are being demonstrated and validated in space with flight on Ex-Alta-1. We present on-orbit data from the boom-deployment and initial operations of the fluxgate sensor and illustrate the potential scientific returns and utility of using CubeSats carrying such fluxgate magnetometers to constitute a magnetospheric constellation mission. We further illustrate the value of scientific constellations using example data from the low-Earth orbit European Space Agency Swarm mission. Swarm data reveal significant changes in the spatiotemporal characteristics of the magnetic fields in the coupled magnetosphere-ionosphere system, even when the spacecraft are separated by only approximately 10 s along track and approximately 1.4° in longitude. This indicates the likely energetic significance of Alfven wave dynamics, and we use Swarm measurements to illustrate the value of satellite constellations for diagnosing magnetosphere-ionosphere coupling even in low-Earth orbit.

Construction of Multimedia Courseware and Web-based E-Learning Courses of "Biomedical Materials".

Science.gov (United States)

Xiaoying, Lu; Jian, He; Tian, Qin; Dongxu, Jiang; Wei, Chen

2005-01-01

In order to reform the traditional teaching methodology and to improve the teaching effect, we developed new teaching system for course "Biomedical Materials" in our university by the support of the computer technique and Internet. The new teaching system includes the construction of the multimedia courseware and web-based e-learning courses. More than 2000 PowerPoint slides have been designed and optimized and flash movies for several capitals are included. On the basis of this multimedia courseware, a web-based educational environment has been established further, which includes course contents, introduction of the teacher, courseware download, study forum, sitemap of the web, and relative link. The multimedia courseware has been introduced in the class teaching for "Biomedical Materials" for 6 years and a good teaching effect has been obtained. The web-based e-learning courses have been constructed for two years and proved that they are helpful for the students by their preparing and reviewing the teaching contents before and after the class teaching.

Reliability of construction materials

International Nuclear Information System (INIS)

Merz, H.

1976-01-01

One can also speak of reliability with respect to materials. While for reliability of components the MTBF (mean time between failures) is regarded as the main criterium, this is replaced with regard to materials by possible failure mechanisms like physical/chemical reaction mechanisms, disturbances of physical or chemical equilibrium, or other interactions or changes of system. The main tasks of the reliability analysis of materials therefore is the prediction of the various failure reasons, the identification of interactions, and the development of nondestructive testing methods. (RW) [de

NVENTIONS IN THE NANOTECHNOLOGICAL AREA PROVIDE INCREASED RESISTANCE OF CONSTRUCTION MATERIALS AND PRODUCTS TO OPERATIONAL LOAD

Directory of Open Access Journals (Sweden)

VLASOV Vladimir Alexeevich

2013-12-01

Full Text Available The invention «Dispersion of Carbon Nanotubes (RU 2494961» can be used in production of modifying additives for construction materials. Dispersion of carbon nanotubes contains, mass %: carbon nanotubes 1–20; surface active agent – sodium chloride of sulfonated derived naphthalene 1–20; fumed silica 5–15; water – the rest. Dispersion can additionally contain ethylene glycol as antifreeze. Dispersion is steady in storage, it is soluble in water, provides increased strength of construction materials. Invention «Building Structures Reinforcement Composition (RU 2493337» can beused in construction to reinforce concrete, brick and masonry structures. Composition contains glass or basalt roving taken in quantity 90÷100 parts by weight, soaked in polymer binder based on epoxy taken in quantity 0,001÷1,5 parts by weight. This invention provides high resistance to operational load.

Knowledge sharing in construction partnering projects - redundancy, boundary objects and brokers

DEFF Research Database (Denmark)

Koch, Christian; Thuesen, Christian

2013-01-01

is on two dialogue excerpts, one on process, and one on product knowledge exchanges. The diversity and disjunctive feature of the practices form a condition of possibility for knowledge handling and synthesis into the built construct. Relation-based interaction is necessary with boundary objects and brokers......This article adopts practice-based theory for understanding inter-organisational knowledge work and extends it with a discussion of the role of redundancy. In this view, a constellation of firms is a multiple configuration of communities of practices, characterised by overlapping practises......, multiple memberships and different levels of participation, and accompanied by a governance frame. The paper discusses central mechanisms for coordinating knowledge in such a complex construction project. The knowledge relations are conceptualised through focusing on redundancy, understood as negotiated...

Cubesat-Based Dtv Receiver Constellation for Ionospheric Tomography

Science.gov (United States)

Bahcivan, H.; Leveque, K.; Doe, R. A.

2013-12-01

The Radio Aurora Explorer mission, funded by NSF's Space Weather and Atmospheric Research program, has demonstrated the utility of CubeSat-based radio receiver payloads for ionospheric research. RAX has primarily been an investigation of microphysics of meter-scale ionospheric structures; however, the data products are also suitable for research on ionospheric effects on radio propagation. To date, the spacecraft has acquired (1) ground-based UHF radar signals that are backscattered from meter-scale ionospheric irregularities, which have been used to measure the dispersion properties of meter-scale plasma waves and (2) ground-based signals, directly on the transmitter-spacecraft path, which have been used to measure radio propagation disturbances (scintillations). Herein we describe the application of a CubeSat constellation of UHF receivers to expand the latter research topic for global-scale ionospheric tomography. The enabling factor for this expansion is the worldwide availability of ground-based digital television (DTV) broadcast signals whose characteristics are optimal for scintillation analysis. A significant part of the populated world have transitioned, or soon to be transitioned, to DTV. The DTV signal has a standard format that contains a highly phase-stable pilot carrier that can be readily adapted for propagation diagnostics. A multi-frequency software-defined radar receiver, similar to the RAX payload, can measure these signals at a large number of pilot carrier frequencies to make radio ray and diffraction tomographic measurements of the ionosphere and the irregularities contained in it. A constellation of CubeSats, launched simultaneously, or in sequence over years, similar to DMSPs, can listen to the DTV stations, providing a vast and dense probing of the ionosphere. Each spacecraft can establish links to a preprogrammed list of DTV stations and cycle through them using time-division frequency multiplexing (TDFM) method. An on board program can

Mission studies on constellation of LEO satellites with remote-sensing and communication payloads

Science.gov (United States)

Chen, Chia-Ray; Hwang, Feng-Tai; Hsueh, Chuang-Wei

2017-09-01

Revisiting time and global coverage are two major requirements for most of the remote sensing satellites. Constellation of satellites can get the benefit of short revisit time and global coverage. Typically, remote sensing satellites prefer to choose Sun Synchronous Orbit (SSO) because of fixed revisiting time and Sun beta angle. The system design and mission operation will be simple and straightforward. However, if we focus on providing remote sensing and store-and-forward communication services for low latitude countries, Sun Synchronous Orbit will not be the best choice because we need more satellites to cover the communication service gap in low latitude region. Sometimes the design drivers for remote sensing payloads are conflicted with the communication payloads. For example, lower orbit altitude is better for remote sensing payload performance, but the communication service zone will be smaller and we need more satellites to provide all time communication service. The current studies focus on how to provide remote sensing and communication services for low latitude countries. A cost effective approach for the mission, i.e. constellation of microsatellites, will be evaluated in this paper.

BAVP: Blockchain-Based Access Verification Protocol in LEO Constellation Using IBE Keys

OpenAIRE

Wei, Songjie; Li, Shuai; Liu, Peilong; Liu, Meilin

2018-01-01

LEO constellation has received intensive research attention in the field of satellite communication. The existing centralized authentication protocols traditionally used for MEO/GEO satellite networks cannot accommodate LEO satellites with frequent user connection switching. This paper proposes a fast and efficient access verification protocol named BAVP by combining identity-based encryption and blockchain technology. Two different key management schemes with IBE and blockchain, respectively...

Computer modelling of structures with account of the construction stages and the time dependent material properties

Directory of Open Access Journals (Sweden)

Traykov Alexander

2015-01-01

Full Text Available Numerical studies are performed on computer models taking into account the stages of construction and time dependent material properties defined in two forms. A 2D model of three storey two spans frame is created. The first form deals with material defined in the usual design practice way - without taking into account the time dependent properties of the concrete. The second form creep and shrinkage of the concrete are taken into account. Displacements and internal forces in specific elements and sections are reported. The influence of the time dependent material properties on the displacement and the internal forces in the main structural elements is tracked down. The results corresponding to the two forms of material definition are compared together as well as with the results obtained by the usual design calculations. Conclusions on the influence of the concrete creep and shrinkage during the construction towards structural behaviour are made.

A Challenging Trio in Space 'Routine' Operations of the Swarm Satellite Constellation

Science.gov (United States)

Diekmann, Frank-Jurgen; Clerigo, Ignacio; Albini, Giuseppe; Maleville, Laurent; Neto, Alessandro; Patterson, David; Nino, Ana Piris; Sieg, Detlef

2016-08-01

Swarm is the first ESA Earth Observation Mission with three satellites flying in a semi-controlled constellation. The trio is operated from ESA's satellite control centre ESOC in Darmstadt, Germany. The Swarm Flight Operations Segment consists of the typical elements of a satellite control system at ESOC, but had to be carefully tailored for this innovative mission. The main challenge was the multi-satellite system of Swarm, which necessitated the development of a Mission Control System with a multi-domain functionality, both in hardware and software and covering real-time and backup domains. This was driven by the need for extreme flexibility for constellation operations and parallel activities.The three months of commissioning in 2014 were characterized by a very tight and dynamically changing schedule of activities. All operational issues could be solved during that time, including the challenging orbit acquisition phase to achieve the final constellation.Although the formal spacecraft commissioning phase was concluded in spring 2014, the investigations for some payload instruments continue even today. The Electrical Field Instruments are for instance still being tested in order to characterize and improve science data quality. Various test phases also became necessary for the Accelerometers on the Swarm satellites. In order to improve the performance of the GPS Receivers for better scientific exploitation and to minimize the failures due to loss of synchronization, a number of parameter changes were commanded via on-board patches.Finally, to minimize the impact on operations, a new strategy had to be implemented to handle single/multi bit errors in the on-board mass Memories, defining when to ignore and when to restore the memory via a re-initialisation.The poster presentation summarizes the Swarm specific ground segment elements of the FOS and explains some of the extended payload commissioning operations, turning Swarm into a most demanding and challenging

78 FR 30295 - Constellation Energy Commoditiesgroup, Inc., ENI USA Gas Marketing LLC, Sequent Energy Canada...

Science.gov (United States)

2013-05-22

..., 13-37-NG, 13-24-NG, 13-28-LNG, and 13-32-LNG] Constellation Energy Commoditiesgroup, Inc., ENI USA... natural gas from/to Canada. Group, Inc. 3247 03/05/13 12-161-LNG...... ENI USA Gas Order granting blanket...

A quantitative evaluation of the environmental impact of the mega constellations

OpenAIRE

Rossi, A.; Alessi, E.M.; Valsecchi, G.B.; Lewis, H.; Radtke, J.; Bombardelli, C.; Bastida Virgili, B.

2017-01-01

The main focus of this work is to highlight the main parameters driving the future evolution of the debris environment, in presence of the planned LEO mega constellation of satellites. First, in order to identify the most important parameters that are actually driving the evolution of the environment and in an effort to discriminate between possibly equivalent scenarios, we applied tools from the statistical sciences, namely the Wilcoxon signed rank test, a non-parametric test which allows us...

Comparative researches concerning cleaning chosen construction materials surface layer using UV and IR laser radiation

International Nuclear Information System (INIS)

Napadlek, W.; Marczak, J.; Kubicki, J.; Szudrowicz, M.

2002-01-01

The paper presents comparative research studies of cleaning out of deposits and pollution disposals on different constructional materials like; steel, cast iron, aluminium, copper by using UV and IR laser radiation of wavelength λ =1.064 μm; λ = 0.532 μm; λ = 0.355 μm and λ = 0.266 μm and also impulse laser TEA CO 2 at radiation λ = 10.6 μm were used for the experiments. Achieved experimental results gave us basic information on parameters and conditions and application of each used radiation wavelength. Each kind of pollution and base material should be individually treated, selecting the length of wave and radiation energy density. Laser microtreatment allows for broad cleaning application of the surface of constructional materials as well as may be used in future during manufacturing processes as: preparation of surface for PVD technology, galvanotechnics, cleaning of the surface of machine parts etc. (author)

48 CFR 52.225-11 - Buy American Act-Construction Materials under Trade Agreements.

Science.gov (United States)

2010-10-01

... safety systems, such as emergency lighting, fire alarm, and audio evacuation systems, that are discrete... 50 percent of the cost of all its components. Components of foreign origin of the same class or kind... description of the foreign and domestic construction materials; (B) Unit of measure; (C) Quantity; (D) Price...

Microstructures and physical properties of waste garnets as a promising construction materials

Directory of Open Access Journals (Sweden)

Habeeb Lateef Muttashar

2018-06-01

Full Text Available Rapid industrial growth has witnessed the ever-increasing utilization of sand from rivers for various construction purposes, which caused an over-exploitation of rivers’ beds and disturbed the eco-system. strong engineering properties of waste garnets offer a recycling alternative to create efficient construction materials. Recycling of garnets provides a cost-effective and environmentally responsible solution rather than dumping it as industrial waste. In this spirit, this article presents an investigation into the capacity of spent garnets as sand replacement. The main parameters studied were the evolution of leaching performance, microstructure of the raw spent garnet and sand specimens. The microstructures, boning vibrations and thermal properties of the raw materials were determined using X-ray diffraction (XRD, field emission scanning microscopy (FESEM, Fourier transform infrared (FTIR spectroscopy, and thermo gravimetric analysis (TGA. Admirable features of the results suggest that the spent garnet is proven to be suitable replacement of sand. It is established that proper exploitation of spent garnet as an alternative to sand could save the earth from depleting the natural resources which is essential for sustainable development. Keywords: Spent garnet, Sand, Micro-structures, Recycling, Concrete

Classical and modern control strategies for the deployment, reconfiguration, and station-keeping of the National Aeronautics and Space Administration (NASA) Benchmark Tetrahedron Constellation

Science.gov (United States)

Capo-Lugo, Pedro A.

Formation flying consists of multiple spacecraft orbiting in a required configuration about a planet or through Space. The National Aeronautics and Space Administration (NASA) Benchmark Tetrahedron Constellation is one of the proposed constellations to be launched in the year 2009 and provides the motivation for this investigation. The problem that will be researched here consists of three stages. The first stage contains the deployment of the satellites; the second stage is the reconfiguration process to transfer the satellites through different specific sizes of the NASA benchmark problem; and, the third stage is the station-keeping procedure for the tetrahedron constellation. Every stage contains different control schemes and transfer procedures to obtain/maintain the proposed tetrahedron constellation. In the first stage, the deployment procedure will depend on a combination of two techniques in which impulsive maneuvers and a digital controller are used to deploy the satellites and to maintain the tetrahedron constellation at the following apogee point. The second stage that corresponds to the reconfiguration procedure shows a different control scheme in which the intelligent control systems are implemented to perform this procedure. In this research work, intelligent systems will eliminate the use of complex mathematical models and will reduce the computational time to perform different maneuvers. Finally, the station-keeping process, which is the third stage of this research problem, will be implemented with a two-level hierarchical control scheme to maintain the separation distance constraints of the NASA Benchmark Tetrahedron Constellation. For this station-keeping procedure, the system of equations defining the dynamics of a pair of satellites is transformed to take in account the perturbation due to the oblateness of the Earth and the disturbances due to solar pressure. The control procedures used in this research will be transformed from a continuous

FORMOSAT-3/COSMIC Spacecraft Constellation System, Mission Results, and Prospect for Follow-On Mission

Directory of Open Access Journals (Sweden)

Chen-Joe Fong

2009-01-01

Full Text Available The FORMOSAT-3/COSMIC spacecraft constellation consisting of six LEO satellites is the world's first operational GPS Radio Occultation (RO mission. The mission is jointly developed by Taiwan¡¦s National Space Organization (NSPO and the United States¡¦UCAR in collaboration with NSF, USAF, NOAA, NASA, NASA's Jet Propulsion Laboratory, and the US Naval Research Laboratory. The FORMOSAT-3/COSMIC satellites were successfully launched from Vandenberg US AFB in California at 0140 UTC 15 April 2006 into the same orbit plane of the designated 516 km altitude. The mission goal is to deploy the six satellites into six orbit planes at 800 km altitude with a 30-degree separation for evenly distributed global coverage. All six FORMOSAT-3/COSMIC satellites are currently maintaining a satisfactory good state-of-health. Five out of six satellites have reached their final mission orbit of 800 km as of November 2007. The data as received by FORMOSAT-3/COSMIC satellites constellation have been processed in near real time into 2500 good ionospheric profiles and 1800 good atmospheric profiles per day. These have outnumbered the worldwide radiosondes (~900 mostly over land launched from the ground per day. The processed atmospheric RO data have been assimilated into the Numerical Weather Prediction (NWP models for real-time weather prediction and typhoon/hurricane forecasting by many major weather centers in the world. This paper describes the FORMOSAT-3/COSMIC satellite constellation system performance and the mission results that span the period from April 2006 to October 2007; and reviews the prospect of a future follow-on mission.

Our Pittsburgh Constellation

Science.gov (United States)

Turnshek, Diane

2015-08-01

Riding on the Pittsburgh mayor’s keen interest in astronomy and the ongoing change of 40,000 city lights from mercury and sodium vapor to shielded LEDs, we organized a series of city-wide celestial art projects to bring attention to the skies over Pittsburgh. Light pollution public talks were held at the University of Pittsburgh’s Allegheny Observatory and other colleges. Earth Hour celebrations kicked off an intensive year of astronomy outreach in the city. Lights went out on March 28, 2015 from 8:30 to 9:30 pm in over fifty buildings downtown and in Oakland (the “Eds and Meds” center, where many Pittsburgh universities and hospitals are located). Our art contest was announced at the De-Light Pittsburgh celebration at the Carnegie Science Center during Astronomy Weekend. “Our Pittsburgh Constellation” is an interactive Google map of all things astronomical in the city. Different colored stars mark locations of planetariums, star parties, classes, observatories, lecture series, museums, telescope manufacturers and participating art galleries. Contest entrants submitted artwork depicting their vision of the constellation figure that incorporates and connects all the “stars” in our custom city map. Throughout the year, over a dozen artists ran workshops on painting star clusters, galaxies, nebulae, comets, planets and aurorae with discussions of light pollution solutions and scientific explanations of what the patrons were painting, including demonstrations with emission tubes and diffraction grating glasses. We will display the celestial art created in this International Year of Light at an art gallery as part of the City’s Department of Innovation & Performance March 2016 Earth Hour gala. We are thankful for the Astronomical Footprint grant from the Heinz Endowments, which allowed us to bring the worlds of science and art together to enact social change.

Development of Additive Construction Technologies for Application to Development of Lunar/Martian Surface Structures Using In-Situ Materials

Science.gov (United States)

Werkheiser, Niki J.; Fiske, Michael R.; Edmunson, Jennifer E.; Khoshnevis, Berokh

2015-01-01

For long-duration missions on other planetary bodies, the use of in situ materials will become increasingly critical. As human presence on these bodies expands, so must the breadth of the structures required to accommodate them including habitats, laboratories, berms, radiation shielding for natural radiation and surface reactors, garages, solar storm shelters, greenhouses, etc. Planetary surface structure manufacturing and assembly technologies that incorporate in situ resources provide options for autonomous, affordable, pre-positioned environments with radiation shielding features and protection from micrometeorites, exhaust plume debris, and other hazards. The ability to use in-situ materials to construct these structures will provide a benefit in the reduction of up-mass that would otherwise make long-term Moon or Mars structures cost prohibitive. The ability to fabricate structures in situ brings with it the ability to repair these structures, which allows for the self-sufficiency and sustainability necessary for long-duration habitation. Previously, under the auspices of the MSFC In-Situ Fabrication and Repair (ISFR) project and more recently, under the jointly-managed MSFC/KSC Additive Construction with Mobile Emplacement (ACME) project, the MSFC Surface Structures Group has been developing materials and construction technologies to support future planetary habitats with in-situ resources. One such additive construction technology is known as Contour Crafting. This paper presents the results to date of these efforts, including development of novel nozzle concepts for advanced layer deposition using this process. Conceived initially for rapid development of cementitious structures on Earth, it also lends itself exceptionally well to the automated fabrication of planetary surface structures using minimally processed regolith as aggregate, and binders developed from in situ materials as well. This process has been used successfully in the fabrication of

Development and mechanical properties of construction materials from lunar simulant

Science.gov (United States)

Desai, Chandra S.

1992-01-01

Development of versatile engineering materials from locally available materials in space is an important step toward the establishment of outposts on the Moon and Mars. Development of the technologies for manufacture of structural and construction materials on the Moon, utilizing local lunar soil (regolith), without the use of water, is an important element for habitats and explorations in space. It is also vital that the mechanical behavior such as strength and tensile, flexural properties, fracture toughness, ductility, and deformation characteristics are defined toward establishment of the ranges of engineering applications of the materials developed. The objectives include two areas: (1) thermal 'liquefaction' of lunar simulant (at about 1100 C) with different additives (fibers, powders, etc.), and (2) development and use of a new triaxial test device in which lunar simulants are first compacted under cycles of loading, and then tested with different vacuums and initial confining or in situ stress. Details of the development of intermediate ceramic composites (ICC) and testing for their flexural and compression characteristics were described in various reports and papers. The subject of behavior of compacted simulant under vacuum was described in previous progress reports and publications; since the presently available device allows vacuum levels up to only 10(exp -4) torr, it is recommended that a vacuum pump that can allow higher levels of vacuum be utilized for further investigation.

Development of construction materials using nano-silica and aggregates recycled from construction and demolition waste.

Science.gov (United States)

Mukharjee, Bibhuti Bhusan; Barai, Sudhirkumar V

2015-06-01

The present work addresses the development of novel construction materials utilising commercial grade nano-silica and recycled aggregates retrieved from construction and demolition waste. For this, experimental work has been carried out to examine the influence of nano-silica and recycled aggregates on compressive strength, modulus of elasticity, water absorption, density and volume of voids of concrete. Fully natural and recycled aggregate concrete mixes are designed by replacing cement with three levels (0.75%, 1.5% and 3%) of nano-silica. The results of the present investigation depict that improvement in early days compressive strength is achieved with the incorporation of nano-silica in addition to the restoration of reduction in compressive strength of recycled aggregate concrete mixes caused owing to the replacement of natural aggregates by recycled aggregates. Moreover, the increase in water absorption and volume of voids with a reduction of bulk density was detected with the incorporation of recycled aggregates in place of natural aggregates. However, enhancement in density and reduction in water absorption and volume of voids of recycled aggregate concrete resulted from the addition of nano-silica. In addition, the results of the study reveal that nano-silica has no significant effect on elastic modulus of concrete. © The Author(s) 2015.

Exploring the Importance of Employing Bio and Nano-Materials for Energy Efficient Buildings Construction

Directory of Open Access Journals (Sweden)

Mona Naguib

2017-03-01

Full Text Available The continued and increasing use of ordinary building materials to house the ever-growing world population ensures growing contributions of carbon (C to the active carbon cycle through carbon dioxide (C02 emissions from combustion and chemical reactions in the raw material to the atmosphere. To minimize this, materials should be conserved, reduce their unnecessary use, produce them more benignly and make them last longer, recycle and reuse materials. Thus, paper will focus on exploring alternative building materials and systems that can be developed in order to balance atmospheric carbon dioxide.  It also presents the Bio-inspired architecture approach that embraces the eco-friendly practices of using Biomaterials and Nano-materials for sustainable dwelling construction through a number of examples that shows how a building can be strongly related to its site.

Stimulating the use of secondary materials in the construction industry: The role of certification

NARCIS (Netherlands)

van Eijk, R.J.; Brouwers, Jos

2002-01-01

Introduction of secondary materials in the construction industry is quite difficult and has not always been successful, even when they satisfy all necessary product demands and environmental (leaching) conditions. Besides the financial and commercial aspects the main problem is convincing the user

Stimulating The Use Of Secondary Materials In The Construction Industry: The Role Of Certification

NARCIS (Netherlands)

van Eijk, R.J.; Brouwers, Jos

2002-01-01

Introduction of secondary materials in the construction industry is quite difficult and has not always been successful, even when they satisfy all necessary product demands and environmental (leaching) conditions. Besides the financial and commercial aspects the main problem is convincing the user

The Orion Constellation as an Installation: An Innovative Three-Dimensional Teaching and Learning Environment

Science.gov (United States)

Brown, Daniel

2013-01-01

Visualizing the three-dimensional distribution of stars within a constellation is highly challenging for both students and educators, but when carried out in an interactive collaborative way, it can create an ideal environment to explore common misconceptions about size and scale within astronomy. We present how the common tabletop activities…

A walk through the heavens a guide to stars and constellations and their legends

CERN Document Server

Heifetz, Milton D

2004-01-01

A Walk through the Heavens is a beautiful and easy-to-use guide to the constellations of the northern hemisphere. Written for the complete beginner, this practical guide introduces the patterns of the starry skies in a memorable way. No equipment is needed, apart from normal sight and clear skies.

Construction material

Science.gov (United States)

Wagh, Arun S [Orland Park, IL; Antink, Allison L [Bolingbrook, IL

2008-07-22

A structural material of a polystyrene base and the reaction product of the polystyrene base and a solid phosphate ceramic is applied as a slurry which includes one or more of a metal oxide or a metal hydroxide with a source of phosphate to produce a phosphate ceramic and a poly (acrylic acid or acrylate) or combinations or salts thereof and polystyrene or MgO applied to the polystyrene base and allowed to cure so that the dried aqueous slurry chemically bonds to the polystyrene base. A method is also disclosed of applying the slurry to the polystyrene base.

CONSTRUCTION MATERIALS FROM WASTE PRODUCTS

Directory of Open Access Journals (Sweden)

Тахира Далиевна Сидикова

2016-02-01

Full Text Available We have studied the physical and chemical processes occurring during the thermal treatment of ceramic masses on the basis of compositions of natural raw materials and waste processing facilities. The study of structures of ceramic samples species has shown different types of crystalline phases.The results have shown that the waste of Kaytashsky tungsten-molybdenum ores (KVMR may be used as the main raw material to develop new compositions for ceramic materials. The optimal compositions of ceramic tiles for the masses and technological parameters of obtaining sintered materials based on the compositions of kaolin fireclay KVMR have been developed.It has been found that the use of the waste of Kaytashskoy tungsten-molybdenum ore (KVMR in the composition of the ceramic material will expand the raw material base of ceramic production, reduce the roasting temperature and the cost of ceramic materials and products.

Proposal for Construction/Demonstration/Implementation of A Material Handling System

International Nuclear Information System (INIS)

Jim Jnatt

2001-01-01

Vortec Corporation, the United States Enrichment Corporation (USEC) and DOE/Paducah propose to complete the technology demonstration and the implementation of the Material Handling System developed under Contract Number DE-AC21-92MC29120. The demonstration testing and operational implementation will be done at the Paducah Gaseous Diffusion Plant. The scope of work, schedule and cost for the activities are included in this proposal. A description of the facility to be constructed and tested is provided in Exhibit 1, attached. The USEC proposal for implementation at Paducah is presented in Exhibit 2, and the commitment letters from the site are included in Exhibit 3. Under our agreements with USEC, Bechtel Jacobs Corporation and DOE/Paducah, Vortec will be responsible for the construction of the demonstration facility as documented in the engineering design package submitted under Phase 4 of this contract on August 9, 2001. USEC will have responsibility for the demonstration testing and commercial implementation of the plant. The demonstration testing and initial commercial implementation of the technology will be achieved by means of a USEC work authorization task with the Bechtel Jacobs Corporation. The initial processing activities will include the processing of approximately 4,250 drums of LLW. Subsequent processing of LLW and TSCA/LLW will be done under a separate contract or work authorization task. To meet the schedule for commercial implementation, it is important that the execution of the Phase 4 project option for construction of the demonstration system be executed as soon as possible. The schedule we have presented herein assumes initiation of the construction phase by the end of September 2001. Vortec proposes to complete construction of the demonstration test system for an estimated cost of $3,254,422. This price is based on the design submitted to DOE/NETL under the Phase 4 engineering design deliverable (9 august 2001). The cost is subject to the

A miniature, low-power scientific fluxgate magnetometer: A stepping-stone to cube-satellite constellation missions

Science.gov (United States)

Miles, D. M.; Mann, I. R.; Ciurzynski, M.; Barona, D.; Narod, B. B.; Bennest, J. R.; Pakhotin, I. P.; Kale, A.; Bruner, B.; Nokes, C. D. A.; Cupido, C.; Haluza-DeLay, T.; Elliott, D. G.; Milling, D. K.

2016-12-01

Difficulty in making low noise magnetic measurements is a significant challenge to the use of cube-satellite (CubeSat) platforms for scientific constellation class missions to study the magnetosphere. Sufficient resolution is required to resolve three-dimensional spatiotemporal structures of the magnetic field variations accompanying both waves and current systems of the nonuniform plasmas controlling dynamic magnetosphere-ionosphere coupling. This paper describes the design, validation, and test of a flight-ready, miniature, low-mass, low-power, and low-magnetic noise boom-mounted fluxgate magnetometer for CubeSat applications. The miniature instrument achieves a magnetic noise floor of 150-200 pT/√Hz at 1 Hz, consumes 400 mW of power, has a mass of 121 g (sensor and boom), stows on the hull, and deploys on a 60 cm boom from a three-unit CubeSat reducing the noise from the onboard reaction wheel to less than 1.5 nT at the sensor. The instrument's capabilities will be demonstrated and validated in space in late 2016 following the launch of the University of Alberta Ex-Alta 1 CubeSat, part of the QB50 constellation mission. We illustrate the potential scientific returns and utility of using a CubeSats carrying such fluxgate magnetometers to constitute a magnetospheric constellation using example data from the low-Earth orbit European Space Agency Swarm mission. Swarm data reveal significant changes in the spatiotemporal characteristics of the magnetic fields in the coupled magnetosphere-ionosphere system, even when the spacecraft are separated by only approximately 10 s along track and approximately 1.4° in longitude.

Long term integrity of spent fuel and construction materials for dry storage facilities

Energy Technology Data Exchange (ETDEWEB)

Saegusa, T [CRIEPI (Japan)

2012-07-01

In Japan, two dry storage facilities at reactor sites have already been operating since 1995 and 2002, respectively. Additionally, a large scale dry storage facility away from reactor sites is under safety examination for license near the coast and desired to start its operation in 2010. Its final storage capacity is 5,000tU. It is therefore necessary to obtain and evaluate the related data on integrity of spent fuels loaded into and construction materials of casks during long term dry storage. The objectives are: - Spent fuel rod: To evaluate hydrogen migration along axial fuel direction on irradiated claddings stored for twenty years in air; To evaluate pellet oxidation behaviour for high burn-up UO{sub 2} fuels; - Construction materials for dry storage facilities: To evaluate long term reliability of welded stainless steel canister under stress corrosion cracking (SCC) environment; To evaluate long term integrity of concrete cask under carbonation and salt attack environment; To evaluate integrity of sealability of metal gasket under long term storage and short term accidental impact force.

A comparison of results for samples collected with bailers constructed of different materials

International Nuclear Information System (INIS)

Thomey, N.; Ogle, R.; Jackson, J.

1992-01-01

A bailer is one of the most common sampling devices used to collect ground water samples. Bailers constructed from various materials are available; teflon, polyvinyl chloride (PVC), polyethylene, and stainless steel are all commonly used. It is widely recognized that sample results can be affected by the material from which the bailer is constructed. Teflon and stainless steel are usually recommended based upon their inert properties. The cost of these bailers is significantly higher than other types. For the purposes of petroleum storage tank investigations, sampling devices that would not compromise sample quality but be more economical than teflon or stainless steel would be especially desirable. Water samples were collected using the different types of bailers; teflon, stainless steel, PVC, and polyethylene. Split samples were analyzed for benzene, toluene, ethylbenzene, total xylenes, and Total Petroleum Hydrocarbons. The analytical results were compared to determine if differences were due to normal analytical variances or due to interaction of the sample with the sampling device. No difference was noted in the results which were obtained

48 CFR 252.225-7045 - Balance of Payments Program-Construction Material Under Trade Agreements.

Science.gov (United States)

2010-10-01

.... Designated country means— (1) A World Trade Organization Government Procurement Agreement (WTO GPA) country... another country, has been substantially transformed in a Free Trade Agreement country into a new and... Program-Construction Material Under Trade Agreements. 252.225-7045 Section 252.225-7045 Federal...

Nanosatellites constellation as an IoT communication platform for near equatorial countries

Science.gov (United States)

Narayanasamy, A.; Ahmad, Y. A.; Othman, M.

2017-11-01

Anytime, anywhere access for real-time intelligence by Internet of Things (IoT) is changing the way that the whole world will operate as it moves toward data driven technologies. Over the next five years, IoT related devices going to have a dramatic breakthrough in current and new applications, not just on increased efficiency and cost reduction on current system, but it also will make trillion-dollar revenue generation and improve customer satisfaction. IoT communications is the networking of intelligent devices which enables data collection from remote assets. It covers a broad range of technologies and applications which connect to the physical world while allowing key information to be transferred automatically. The current terrestrial wireless communications technologies used to enable this connectivity include GSM, GPRS, 3G, LTE, WIFI, WiMAX and LoRa. These connections occur short to medium range distance however, none of them can cover a whole country or continent and the networks are getting congested with the multiplication of IoT devices. In this study, we discuss a conceptual design of a nanosatellite constellation those can provide a space-based communication platform for IoT devices for near Equatorial countries. The constellation design i.e. the orbital plane and number of satellites and launch deployment concepts are presented.

Investigation of Preservice Science Teachers' Comprehension of the Star, Sun, Comet and Constellation Concepts

Science.gov (United States)

Cevik, Ebru Ezberci; Kurnaz, Mehmet Altan

2017-01-01

The purpose of this study is to reveal preservice science teachers' perceptions related to the sun, star, comet and constellation concepts. The research was carried out by 56 preservice science teachers (4th grade) at Kastamonu University taking astronomy course in 2014-2015 academic year. For data collection open-ended questions that required…

Nondestructive indication of fatigue damage and residual lifetime in ferromagnetic construction materials

Czech Academy of Sciences Publication Activity Database

Tomáš, Ivan; Kovářík, O.; Vértesy, G.; Kadlecová, Jana

2014-01-01

Roč. 25, č. 6 (2014), "065601-1"-"065601-10" ISSN 0957-0233. [International Symposium on Measurement Technology and Intelligent Instruments /11./ (ISMTII). Aachen, 01.07.2013-03.07.2013] R&D Projects: GA ČR(CZ) GAP108/12/1872 Institutional support: RVO:68378271 Keywords : fatigue * residual lifetime * magnetic nondestructive evaluation * ferromagnetic construction materials Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.433, year: 2014

Activation of accelerator construction materials by heavy ions

Energy Technology Data Exchange (ETDEWEB)

Katrík, P., E-mail: p.katrik@gsi.de [GSI Darmstadt, Planckstrasse 1, D-64291 (Germany); Mustafin, E. [GSI Darmstadt, Planckstrasse 1, D-64291 (Germany); Hoffmann, D.H.H. [TU Darmstadt, Schlossgartenstraße 9, D-64289 (Germany); Pavlovič, M. [FEI STU Bratislava, Ilkovičova 3, SK-81219 (Slovakia); Strašík, I. [GSI Darmstadt, Planckstrasse 1, D-64291 (Germany)

2015-12-15

Activation data for an aluminum target irradiated by 200 MeV/u {sup 238}U ion beam are presented in the paper. The target was irradiated in the stacked-foil geometry and analyzed using gamma-ray spectroscopy. The purpose of the experiment was to study the role of primary particles, projectile fragments, and target fragments in the activation process using the depth profiling of residual activity. The study brought information on which particles contribute dominantly to the target activation. The experimental data were compared with the Monte Carlo simulations by the FLUKA 2011.2c.0 code. This study is a part of a research program devoted to activation of accelerator construction materials by high-energy (⩾200 MeV/u) heavy ions at GSI Darmstadt. The experimental data are needed to validate the computer codes used for simulation of interaction of swift heavy ions with matter.

THE COMPLEX USE OF LOCAL TYPES OF FUEL IN THE POROUS CONSTRUCTION MATERIALS PRODUCTION

Directory of Open Access Journals (Sweden)

N. P. Voronova

2014-01-01

Full Text Available The article presents a comprehensive low-waste technology is the use of local fuels, which can be used in the technology of some porous building materials. Also provides new methods of preparation of porous building materials based on aggloporite using local fuels and waste energy on the basis of milled peat, fuel briquettes and wood chips allow to replace expensive imported components that comprise the raw mixtures (coal, anthracite.On the basis of mathematical modeling of cooling in reheat furnaces pusher drive developed a method of engineering calculation mode batch hardening in agglomeration. Submitted constructive solution for the development of the cooling charge with thermophysical rational justification cooling modes. A study of the temperature distribution within the charge depending on the different speeds of the belt sintering machine, and hence on the cooling time.The characteristics of the raw material deposits "Fanipol" and the optimal composition of the charge which includes loam, coal, milled peat. In industrial research obtained aggloporite this formulation has shown positive results in strength and density. Established that by decreasing the particle size of the fuel increases the redox potential of the combustion products, which reduces the height of the oxidizing zone and the speed of the sintering raw mix. These processes increase the productivity of sinter machine.Technology is implemented on the "Minsk factory of building materials". The tests analyzed production technology porous construction materials using milled peat with the addition of sawdust. The study results recommend further use of sapropel, which cost significantly lower raw material mixture of submissions and in their physical and mechanical properties much closer to the properties of milled peat.

USAGE OF FILTERS FROM FIBROUS MATERIALS IN AMELIORATIVE AND HYDRO-TECHNICAL CONSTRUCTION

Directory of Open Access Journals (Sweden)

V. T. Klimkov

2016-01-01

Full Text Available Construction of first drainage tubular systems has been facing such problem as their protection against silting-up by soil particles penetrating through input openings. Searches and investigations have led to usage of various fibrous materials which are playing the role of filters. At the beginning glass-fibre mats have been widely applied for this purpose. However, the mats possessing good filtration properties have had a number of fundamental disadvantages. Works executed at the Institute of Mechanics of Metal Polymeric Systems (Gomel, Republic of Belarus have played a big role in usage of plastic materials. A new technology has been developed with the purpose to obtain thermally-bonded fibres from thermoplastic material. The fibres have been called as polyethylene mats. Investigation of their properties has been carried out under load and it has revealed that their lateral and longitudinal permeability becomes equal at specified pressures, in other words the material takes an isotropic state. The considered interactions of filtrating material and skeleton frame have shown that the main water filtration occurs directly above perforation holes while the material above blind frame sections does not participate in the process. Due to this a new design of the filtrating element has been developed and it can be used in water intake systems for surface and underground water. The filtrating element consists of the skeleton frame with openings and a filtration covering which is installed on the frame. Water-feeding groove cavities are located on the skeleton frame and they are dispersing from perforation holes in the form of beams. These grooves can have side branches of the second, third and other orders. As beam-like arrangement of grooves creates the shortest flow paths for filtrated water from periphery to frame holes and area of groove cross section exceeds the area of poral holes in water in-take covering by a factor of hundreds, it is possible

Temperament and attachment: one construct or two?

Science.gov (United States)

Mangelsdorf, S C; Frosch, C A

1999-01-01

In this chapter we described the constructs of temperament and attachment and have discussed similarities and differences between the two. We addressed the issue of whether temperament contributes to overall attachment security or to the specific type of attachment that children display. We conclude that although temperament may influence the type of secure and insecure attachment relationship children form with their parent, temperament alone will not determine if a child is classified as securely or insecurely attached. We presented evidence suggesting that certain dimensions of temperament, specifically negative emotionality, may be associated with infants' behavior during the Strange Situation, such as proneness-to-distress during separations. However, we noted that these temperament dimensions do not predict overall security of attachment. It is likely that although no single temperament characteristic, such as proneness-to-distress, in and of itself determines overall attachment security, it is possible that a constellation of temperament characteristics may be more strongly related to attachment security. The examination of constellations of temperament characteristics may be particularly useful for furthering our understanding of individual differences within attachment classifications. Such an approach may elucidate the reasons why infants are classified into one subgroup of secure, insecure-avoidant, or insecure-resistant attachment versus another subgroup. Furthermore, we suggest that the collection of findings regarding temperament and attachment not only underscores the importance of a transactional approach to early social-emotional development, but emphasizes that temperament and attachment can make unique and interactive contributions to children's social-emotional functioning. That is, the goodness-of-fit between infant and parent characteristics may best predict security of attachment. Although child characteristics clearly contribute to the

Flower elliptical constellation of millimeter-wave radiometers for precipitating cloud monitoring at geostationary scale

Science.gov (United States)

Marzano, F. S.; Cimini, D.; Montopoli, M.; Rossi, T.; Mortari, D.; di Michele, S.; Bauer, P.

2009-04-01

Millimeter-wave observation of the atmospheric parameters is becoming an appealing goal within satellite radiometry applications. The major technological advantage of millimeter-wave (MMW) radiometers is the reduced size of the overall system, for given performances, with respect to microwave sensor. On the other hand, millimeter-wave sounding can exploit window frequencies and various gaseous absorption bands at 50/60 GHz, 118 GHz and 183 GHz. These bands can be used to estimate tropospheric temperature profiles, integrated water vapor and cloud liquid content and, using a differentia spectral mode, light rainfall and snowfall. Millimeter-wave radiometers, for given observation conditions, can also exhibit relatively small field-of-views (FOVs), of the order of some kilometers for low-Earth-orbit (LEO) satellites. However, the temporal resolution of LEO millimeter-wave system observations remains a major drawback with respect to the geostationary-Earth-orbit (GEO) satellites. An overpass every about 12 hours for a single LEO platform (conditioned to a sufficiently large swath of the scanning MMW radiometer) is usually too much when compared with the typical temporal scale variation of atmospheric fields. This feature cannot be improved by resorting to GEO platforms due to their high orbit altitude and consequent degradation of the MMW-sensor FOVs. A way to tackle this impasse is to draw our attention at the regional scale and to focus non-circular orbits over the area of interest, exploiting the concept of micro-satellite flower constellations. The Flower Constellations (FCs) is a general class of elliptical orbits which can be optimized, through genetic algorithms, in order to maximize the revisiting time and the orbital height, ensuring also a repeating ground-track. The constellation concept nicely matches the choice of mini-satellites as a baseline choice, due to their small size, weight (less than 500 kilograms) and relatively low cost (essential when

Advanced FRP for flooring in buildings: a low carbon material application in the construction industry

OpenAIRE

Gao, Yijian

2013-01-01

Fibre-reinforced polymers (FRP) are building materials that permit both the improvement of long-term building performance and the simplification of the construction process, thanks to their high specific strength, low thermal conductivity, good environmental resistance, and ability to be formed into complex shapes. FRP materials are well-suited to fulfilling many building functions. By integrating traditionally separate building systems and layers into single function-integrated components, a...

Perceived visual informativeness (PVI): construct and scale development to assess visual information in printed materials.

Science.gov (United States)

King, Andy J; Jensen, Jakob D; Davis, LaShara A; Carcioppolo, Nick

2014-01-01

There is a paucity of research on the visual images used in health communication messages and campaign materials. Even though many studies suggest further investigation of these visual messages and their features, few studies provide specific constructs or assessment tools for evaluating the characteristics of visual messages in health communication contexts. The authors conducted 2 studies to validate a measure of perceived visual informativeness (PVI), a message construct assessing visual messages presenting statistical or indexical information. In Study 1, a 7-item scale was created that demonstrated good internal reliability (α = .91), as well as convergent and divergent validity with related message constructs such as perceived message quality, perceived informativeness, and perceived attractiveness. PVI also converged with a preference for visual learning but was unrelated to a person's actual vision ability. In addition, PVI exhibited concurrent validity with a number of important constructs including perceived message effectiveness, decisional satisfaction, and three key public health theory behavior predictors: perceived benefits, perceived barriers, and self-efficacy. Study 2 provided more evidence that PVI is an internally reliable measure and demonstrates that PVI is a modifiable message feature that can be tested in future experimental work. PVI provides an initial step to assist in the evaluation and testing of visual messages in campaign and intervention materials promoting informed decision making and behavior change.

Combination of precise GNSS orbit and clock solutions in a multi-constellation, multi-frequency environment

Science.gov (United States)

Ortiz Geist, Estefania

2015-04-01

Precise GNSS orbit and clock solutions are essential for the generation of the Terrestrial Reference Frame (TRF) and required for a broad variety of applications. Over the last decades the combination products of the International GNSS Service (IGS) have become the standard for all kinds of GNSS applications requiring highest accuracy. The emerging new GNSS constellations Galileo, BeiDou and the QZSS as well as the modernization of the already established GPS and GLONASS constellations will stimulate a new development in the GNSS data processing in order to gain be best benefit from the new signals and systems for geodetic and geodynamic applications. This introduces the question regarding the influence of this development on the orbit and clock products. What are the consequences for the consistency of the contributions from the Analysis Centres (ACs) of the IGS and how does the combination procedure need to react on his development? Another set of questions is related to the expected scenario in which not all IGS ACs will likely include all GNSS. The algorithm for the orbit and clock combination needs to be adapted for a multi-system combination to keep on one hand the internal consistency between the GNSS during the combination procedure but also consider the differences in the expected orbit qualities between the satellite systems (e.g., due to the number of satellites or network coverage). To investigate these questions ESOC and AIUB have agreed on a joint research fellowship for three years. The objective of this research is to analyse the capabilities and challenges when combining hybrid multi-GNSS solutions and to develop a concept, which compares and combines orbit and clock contributions to come up with a consistent, reliable, truly combined multi-GNSS combination product. Well-defined test scenarios shall be constructed and analysed based on the GNSS data processing software packages in the two institutions, namely "NAPEOS" and "Bernese GNSS Software

Analysis of chromium and sulphate origins in construction recycled materials based on leaching test results.

Science.gov (United States)

Del Rey, I; Ayuso, J; Galvín, A P; Jiménez, J R; López, M; García-Garrido, M L

2015-12-01

Twenty samples of recycled aggregates from construction and demolition waste (CDW) with different compositions collected at six recycling plants in the Andalusia region (south of Spain) were characterised according to the Landfill Directive criteria. Chromium and sulphate were identified as the most critical compounds in the leachates. To detect the sources of these two pollutant constituents in recycled aggregate, environmental assessments were performed on eight construction materials (five unused ceramic materials, two old crushed concretes and one new mortar manufactured in the laboratory). The results confirmed that leached sulphate and Cr were mainly released by the ceramic materials (bricks and tiles). To predict the toxicological consequences, the oxidation states of Cr (III) and Cr (VI) were measured in the leachates of recycled aggregates and ceramic materials classified as non-hazardous. The bricks and tiles mainly released total Cr as Cr (III). However, the recycled aggregates classified as non-hazardous according to the Landfill Directive criteria mainly released Cr (VI), which is highly leachable and extremely toxic. The obtained results highlight the need for legislation that distinguishes the oxidative state in which chromium is released into the environment. Leaching level regulations must not be based solely on total Cr, which can lead to inaccurate predictions. Copyright © 2015 Elsevier Ltd. All rights reserved.

Rapid Construction of Fe-Co-Ni Composition-Phase Map by Combinatorial Materials Chip Approach.

Science.gov (United States)

Xing, Hui; Zhao, Bingbing; Wang, Yujie; Zhang, Xiaoyi; Ren, Yang; Yan, Ningning; Gao, Tieren; Li, Jindong; Zhang, Lanting; Wang, Hong

2018-03-12

One hundred nanometer thick Fe-Co-Ni material chips were prepared and isothermally annealed at 500, 600, and 700 °C, respectively. Pixel-by-pixel composition and structural mapping was performed by microbeam X-ray at synchrotron light source. Diffraction images were recorded at a rate of 1 pattern/s. The XRD patterns were automatically processed, phase-identified, and categorized by hierarchical clustering algorithm to construct the composition-phase map. The resulting maps are consistent with corresponding isothermal sections reported in the ASM Alloy Phase Diagram Database, verifying the effectiveness of the present approach in phase diagram construction.

Leaching of additives from construction materials to urban storm water runoff

DEFF Research Database (Denmark)

Burkhardt, Mike; Zuleeg, S.; Boller, M.

2011-01-01

Urban water management requires further clarification about pollutants in storm water. Little is known about the release of organic additives used in construction materials and the impact of these compounds to storm water runoff. We investigated sources and pathways of additives used...... shows approximately one to two orders of magnitude lower concentrations. Concentrations decreased also during individual runoff events. In storm water and receiving water the occurrence of additives did not follow the typical first flush model. This can be explained by the release lasting over the time...

Social construction and materiality: the limits of indeterminacy in therapeutic settings.

Science.gov (United States)

Lannamann, J W

1998-01-01

By drawing parallels between the courtroom testimony of a Christian Science practitioner and an intersession conversation between systemic family therapists, I critique the abstract idealism of language-centered social constructionism. I argue that social constructionist inquiry that highlights the indeterminacy of meaning without a corresponding emphasis on the responsive embodied practices of family members glosses over the material conditions shaping the politics of interaction. The implications of this problem are discussed as they relate to the setting of family therapy, where social construction theory is often used to guide practical interventions.

BER analysis for MPAM signal constellations in the presence of fading and ADC quantization noise

NARCIS (Netherlands)

Rizvi, U.H.; Janssen, G.J.M.; Weber, J.H.

2009-01-01

In this letter, closed-form expressions for the bit error rate of M-ary pulse amplitude modulated signal constellations as a function of the analog-to-digital converter word length, the signal-to-noise ratio and the fading distribution, are derived. These results allow for a rapid and accurate

The design, construction and testing of packaging[Radioactive materials

Energy Technology Data Exchange (ETDEWEB)

NONE

1976-07-01

Essentially uniform regulations, based on the IAEA Regulations for the Safe Transport of Radioactive Materials, have been adopted on a world-wide basis with the aim of ensuring safety in the transport of radioactive and fissile substances by road, rail, sea and air. The application of these regulations over a period of almost 20 years has resulted in practically complete safety in the sense that there has been no evidence of death or injury that could be attributed to the special properties of the material even when consignments were involved in serious accidents. In the regulations, reliance is placed, to the greatest extent possible, on the packaging to provide adequate shielding and containment of the contents under both normal transport and accident conditions. The Agency organized an international seminar in 1971 to consider the performance tests that have to be applied to packaging to demonstrate compliance with the regulatory requirements. The general conclusion was that the testing programme specified in the regulations was adequate for the near future, but that further consideration should be given to assessing the risks presented by the increasing volume of transport. The second international seminar, which is the subject of this report, dealt with all aspects of the design, construction and testing of packaging for the transport both of relatively small quantities of radioactive substances, which are being used to an ever increasing extent for medical and research purposes, and of the much larger quantities arising in various stages of the nuclear fuel cycle. The programme covered the general requirements for packaging; risk assessment for the transport of various radioactive and fissile substances, including plutonium; specific features of the design and construction of packaging; quality assurance; damage simulation tests, including calculational methods and scale-model testing; tests for the retention of shielding and containment after damage; and the

Kennedy Space Center: Constellation Program Electrical Ground Support Equipment Research and Development

Science.gov (United States)

McCoy, Keegan

2010-01-01

The Kennedy Space Center (KSC) is NASA's spaceport, launching rockets into space and leading important human spaceflight research. This spring semester, I worked at KSC on Constellation Program electrical ground support equipment through NASA's Undergraduate Student Research Program (USRP). This report includes a discussion of NASA, KSC, and my individual research project. An analysis of Penn State's preparation of me for an internship and my overall impressions of the Penn State and NASA internship experience conclude the report.

EI Scale: an environmental impact assessment scale related to the construction materials used in the reinforced concrete

Directory of Open Access Journals (Sweden)

Gilson Morales

2010-12-01

Full Text Available This study aimed to create EI Scal, an environmental impact assessment scal, related to construction materials used in the reinforced concrete structure production. The main reason for that was based on the need to classify the environmental impact levels through indicators to assess the damage level process. The scale allowed converting information to estimate the environmental impact caused. Indicators were defined trough the requirements and classification criteria of impact aspects considering the eco-design theory. Moreover, the scale allowed classifying the materials and processes environmental impact through four score categories which resulted in a single final impact score. It was concluded that the EI scale could be cheap, accessible, and relevant tool for environmental impact controlling and reduction, allowing the planning and material specification to minimize the construction negative effects caused in the environment.

Estimation of the magnetic field gradient tensor using the Swarm constellation

DEFF Research Database (Denmark)

Kotsiaros, Stavros; Finlay, Chris; Olsen, Nils

2014-01-01

For the first time, part of the magnetic field gradient tensor is estimated in space by the Swarm mission. We investigate the possibility of a more complete estimation of the gradient tensor exploiting the Swarm constellation. The East-West gradients can be approximated by observations from...... deviations compared to conventional vector observations at almost all latitudes. Analytical and numerical analysis of the spectral properties of the gradient tensor shows that specific combinations of the East-West and North-South gradients have almost identical signal content to the radial gradient...

Brownfields Recover Your Resources - Reduce, Reuse, and Recycle Construction and Demolition Materials at Land Revitalization Projects

Science.gov (United States)

This document provides background information on how the sustainable reuse of brownfield properties includes efforts to reduce the environmental impact by reusing and recycling materials generated during building construction, demolition, or renovation.

ALLUVIAL DEPOSITS AS A SUBSOIL AND MATERIAL FOR BASIC HYDRO-TECHNICAL CONSTRUCTIONS

Directory of Open Access Journals (Sweden)

Jędrzej Wierzbicki

2015-11-01

Full Text Available The article presents an analysis of geotechnical parameters of the alluvial deposit (the areas of the Vistula and Warta river valleys with a view to using the soil as an earth construction material and as a foundation for buildings constructed on the grounds tested. Strength and deformation parameters of the subsoil tested were identified by the CPTU (cone penetration test and DMT (flat dilatometer test methods, as well as by the vane test (VT. The article includes the analysis of overconsolidation process of the soil tested and a formula for the identification of the overconsolidation ratio OCR. Equation 4 reflects the relation between the undrained shear strength and plasticity of the silts analyzed and the OCR value. The analysis resulted in the determination of the Nkt coefficient, which might be used to identify the undrained shear strength of both sediments tested. On the basis of a detailed analysis of changes in terms of the constrained oedometric modulus M0, the relations between the said modulus, the liquidity index and the OCR value were identified. Mayne’s formula (1995 was used to determine the M0 modulus from the CPTU test. The usefulness of the alluvial deposit as an earth construction material was analysed after their structure had been destroyed and compacted with a Proctor apparatus. In cases of samples characterized by different water content and soil particle density, the analysis of changes in terms of cohesion and the internal friction angle proved that these parameters are influenced by the soil phase composition. On the basis of the tests, it was concluded that the most desirable shear strength parameters are achieved when the silt is compacted below the optimum water content.

Construction and testing of simple airfoils to demonstrate structural design, materials choice, and composite concepts

Science.gov (United States)

Bunnell, L. Roy; Piippo, Steven W.

1993-01-01

The objective of this educational exercise is to have students build and evaluate simple wing structures, and in doing so, learn about materials choices and lightweight construction methods. A list of equipment and supplies and the procedure for the experiment are presented.

Life Cycle Greenhouse Gas Emissions and Energy Analysis of Passive House with Variable Construction Materials

Science.gov (United States)

Baďurová, Silvia; Ponechal, Radoslav; Ďurica, Pavol

2013-11-01

The term "passive house" refers to rigorous and voluntary standards for energy efficiency in a building, reducing its ecological footprint. There are many ways how to build a passive house successfully. These designs as well as construction techniques vary from ordinary timber constructions using packs of straw or constructions of clay. This paper aims to quantify environmental quality of external walls in a passive house, which are made of a timber frame, lightweight concrete blocks and sand-lime bricks in order to determine whether this constructional form provides improved environmental performance. Furthermore, this paper assesses potential benefit of energy savings at heating of houses in which their external walls are made of these three material alternatives. A two storey residential passive house, with floorage of 170.6 m2, was evaluated. Some measurements of air and surface temperatures were done as a calibration etalon for a method of simulation.

Analysis of Construction Material Procurement Retardation on Sepaku-Petung Rigid Pavement Improvement Project in East Kalimantan Province

Directory of Open Access Journals (Sweden)

Rama Nugraha

2017-11-01

Full Text Available his study aims to know the factors influencing the retardation in procurement of construction materials on Sepaku-Petung pavement improvement project in East Kalimantan Province;to know the most dominant factor affecting the retardation in procurement of construction materials on Sepaku-Petung pavement improvement project in East Kalimantan Province; to determine what strategies that minimize the waiting time of materials in the improvement of Sepaku-Petung pavement project in East Kalimantan Province. This study used quantitative research method. The data was collected through interview, questionnaire distribution, and discussion forum. Based on the results of research and data analysis conducted, it can be concluded thatsuppliers, contractors, field conditions, and unpredictable conditionswere affecting the retardation in procurement of materials in the pavement improvement project in East Kalimantan. Field condition was the most dominant factors in the realization of Sepaku-Petung pavement improvement project in East Kalimantan province. Type B (Retarding Admixtures could be added to retard the time-binding of the concrete (setting time, therefore minimizing material procurement waiting time. The contractor should also build his own supplier close to the project site to reduce the distance between the concrete supplier location and the project site.

Extraterrestrial materials processing and construction

Science.gov (United States)

Criswell, D. R.

1978-01-01

Applications of available terrestrial skills to the gathering of lunar materials and the processing of raw lunar materials into industrial feed stock were investigated. The literature on lunar soils and rocks was reviewed and the chemical processes by which major oxides and chemical elements can be extracted were identified. The gathering of lunar soil by means of excavation equipment was studied in terms of terrestrial experience with strip mining operations on earth. The application of electrostatic benefication techniques was examined for use on the moon to minimize the quantity of materials requiring surface transport and to optimize the stream of raw materials to be transported off the moon for subsequent industrial use.

Electrochemical construction

Science.gov (United States)

Einstein, Harry; Grimes, Patrick G.

1983-08-23

An electrochemical cell construction features a novel co-extruded plastic electrode in an interleaved construction with a novel integral separator-spacer. Also featured is a leak and impact resistant construction for preventing the spill of corrosive materials in the event of rupture.

Cross section for calculating the helium formation rate in construction materials irradiated by nucleons at energies to 800 MeV

International Nuclear Information System (INIS)

Konobeev, A.Yu.; Korovin, Yu.A.

1992-01-01

Recently, effects related to the formation of helium in irradiated construction materials have been studied extensively. Data on the nuclear cross sections for producing helium in these materials form the initial information necessary for such investigations. If the spectrum of the incoming particles is known, the value of the helium production cross section makes it possible to calculate the helium generation rate. In recent years, plans and simulating experiments on radiating materials with high-energy particles made it necessary to determine the helium production cross sections in constructionmaterials, which are irradiated by protons and neutrons with energies to 800 MeV. Helium-formation cross sections have been calculated at these energies. However, a correct description of the experimental data for various construction materials does not yet exist. For example, the calculated helium-formation cross sections turned out to overestimate the experimental data, and to underestimate the experimental data. The objective here is to calculate the helium-formation cross sections for various construction materials, which are irradiated by protons and neutrons to energies from 20 to 800 MeV, and to analyze the probable causes of deviations between experimental and earlier calculated cross sections

Stars, Manuscripts, and Astrolabes-The Stellar Constellations in a Group of Medieval Manuscripts between Latin Literature and a New Science of the Stars

Science.gov (United States)

Metzger, W.

2011-06-01

The European Middle Ages inherited star names and constellations from Roman antiquity, mostly via Latin literary texts. When, from the 11th century onwards, Arabic texts and instruments became available, figures and vocabulary at first where not compatible with this tradition. The example of an excerpt from Pseudo-Hyginus De Astronomia shows, how a Roman text on the constellations was revised and supplemented with the names of the astrolabe-stars to combine the two different traditions.

BRITE Constellation: data processing and photometry

Science.gov (United States)