Absolute production rate measurements of nitric oxide by an atmospheric pressure plasma jet (APPJ)

International Nuclear Information System (INIS)

Pipa, A V; Bindemann, T; Foest, R; Kindel, E; Roepcke, J; Weltmann, K-D

2008-01-01

Tunable diode laser absorption spectroscopy (TDLAS) has been applied to measure the absolute production rate of NO molecules in the gas phase of an atmospheric pressure plasma jet (APPJ) operating at rf (13.56 MHz) in argon with small (up to 1%) admixtures of air. The resulting NO production rates were found to be in the range (0.1-80) x 10 -3 sccm or (0.05-35) x 10 18 molecules s -1 depending on the experimental conditions. Maximum rates were obtained at 0.2% air. For TDLAS measurements the APPJ was arranged inside an astigmatic multi-pass cell of Herriott type with 100 m absorption length. The insertion into a closed volume differs slightly from the normal, open operation with the jet propagating freely into air. Therefore, the measuring results are compared with optical emission of the open jet to verify equivalent experimental conditions. The dependence of the optical emission of NO (237 nm) on power and gas mixture has been measured. The similar shape of the dependence of absorption and emission signals gives evidence that the comparability of experimental conditions is sufficiently satisfied. It is concluded that the NO production rate of the APPJ in ambient air can be characterized using TDLAS and provides reliable results in spite of differing experimental conditions due to the set-up.

New method of noncontact temperature measurement in on-line textile production

Science.gov (United States)

Cheng, Xianping; Song, Xing-Li; Deng, Xing-Zhong

1993-09-01

Based on the condition of textile production the method of infrared non-contact temperature measurement is adcpted in the heat-setting and drying heat-treatment process . This method is used to monitor the moving cloth. The temperature of the cloth is displayed rapidly and exactly. The principle of the temperature measurement is analysed theoretically in this paper. Mathematical analysis and calculation are used for introducing signal transmitting method. Adopted method of combining software with hardware the temperature is corrected and compensated with the aid of a single-chip microcomputer. The results of test indicate that the application of temperature measurement instrument provides reliable parameters in the quality control. And it is an important measure on improving the quality of products.

Telemetric measurement system of beehive environment conditions

Science.gov (United States)

Walendziuk, Wojciech; Sawicki, Aleksander

2014-11-01

This work presents a measurement system of beehive environmental conditions. The purpose of the device is to perform measurements of parameters such as ambient temperature, atmospheric pressure, internal temperature, humidity and sound level. The measured values were transferred to the MySQL database, which is located on an external server, with the use of GPRS protocol. A website presents the measurement data in the form of tables and graphs. The study also shows exemplary results of environmental conditions measurements recorded in the beehive by hour cycle.

Top quark production cross-section measurements

CERN Document Server

Chen, Ye; The ATLAS collaboration

2017-01-01

Measurements of the inclusive and differential cross-sections for top-quark pair and single top production cross sections in proton-proton collisions with the ATLAS detector at the Large Hadron Collider are presented at center-of-mass energies of 8 TeV and 13 TeV. The inclusive measurements reach high precision and are compared to the best available theoretical calculations. These measurements, including results using boosted tops, probe our understanding of top-pair production in the TeV regime. The results are compared to Monte Carlo generators implementing LO and NLO matrix elements matched with parton showers and NLO QCD calculations. For the t-channel single top measurement, the single top-quark and anti-top-quark total production cross-sections, their ratio, as well as differential cross sections are also presented. A measurement of the production cross-section of a single top quark in association with a W boson, the second largest single-top production mode, is also presented. Finally, measurements of ...

Measuring healthcare productivity - from unit to system level.

Science.gov (United States)

Kämäräinen, Vesa Johannes; Peltokorpi, Antti; Torkki, Paulus; Tallbacka, Kaj

2016-04-18

Purpose - Healthcare productivity is a growing issue in most Western countries where healthcare expenditure is rapidly increasing. Therefore, accurate productivity metrics are essential to avoid sub-optimization within a healthcare system. The purpose of this paper is to focus on healthcare production system productivity measurement. Design/methodology/approach - Traditionally, healthcare productivity has been studied and measured independently at the unit, organization and system level. Suggesting that productivity measurement should be done in different levels, while simultaneously linking productivity measurement to incentives, this study presents the challenges of productivity measurement at the different levels. The study introduces different methods to measure productivity in healthcare. In addition, it provides background information on the methods used to measure productivity and the parameters used in these methods. A pilot investigation of productivity measurement is used to illustrate the challenges of measurement, to test the developed measures and to prove the practical information for managers. Findings - The study introduces different approaches and methods to measure productivity in healthcare. Practical implications - A pilot investigation of productivity measurement is used to illustrate the challenges of measurement, to test the developed measures and to prove the practical benefits for managers. Originality/value - The authors focus on the measurement of the whole healthcare production system and try to avoid sub-optimization. Additionally considering an individual patient approach, productivity measurement is examined at the unit level, the organizational level and the system level.

Modifying Yeast Tolerance to Inhibitory Conditions of Ethanol Production Processes

DEFF Research Database (Denmark)

Caspeta, Luis; Castillo, Tania; Nielsen, Jens

2015-01-01

Saccharomyces cerevisiae strains having a broad range of substrate utilization, rapid substrate consumption, and conversion to ethanol, as well as good tolerance to inhibitory conditions are ideal for cost-competitive ethanol production from lignocellulose. A major drawback to directly design S....... cerevisiae tolerance to inhibitory conditions of lignocellulosic ethanol production processes is the lack of knowledge about basic aspects of its cellular signaling network in response to stress. Here, we highlight the inhibitory conditions found in ethanol production processes, the targeted cellular...... functions, the key contributions of integrated -omics analysis to reveal cellular stress responses according to these inhibitors, and current status on design-based engineering of tolerant and efficient S. cerevisiae strains for ethanol production from lignocellulose....

Fission product releases at severe LWR accident conditions: ORNL/CEA measurements versus calculations

Energy Technology Data Exchange (ETDEWEB)

Andre, B.; Ducros, G.; Leveque, J.P. [CEA Centre d`Etudes de Grenoble, 38 (France). Dept. de Thermohydraulique et de Physique; Osborne, M.F.; Lorenz, R.A. [Oak Ridge National Lab., TN (United States); Maro, D. [CEA Centre d`Etudes de Fontenay-aux-Roses, 92 (France). Dept. de Protection de l`Environnement et des Installations

1995-12-31

Experimental programs in the United States and France have followed similar paths in supplying much of the data needed to analyze severe accidents. Both the HI/VI program, conducted at the Oak Ridge National Laboratory (ORNL) under the sponsorship of the U. S. Nuclear Regulatory Commission (NRC), and the HEVA/VERCORS program, supported by IPSN-Commissariat a l`Energie Atomique (CEA) and carried out at the Centre d`Etudes Nucleaires de Grenoble, have studied fission product release from light water reactor (LWR) fuel samples during test sequences representative of severe accidents. Recognizing that more accurate data, i.e., a better defined source term, could reduce the safety margins included in the rather conservative source terms originating from WASH-1400, the primary objective of these programs has been to improve the data base concerning fission product release and behavior at high temperatures. To facilitate the comparison, a model based on fission product diffusion mechanisms that was developed at ORNL and adapted with CEA experimental data is proposed. This CEA model is compared with the ORNL experimental data in a blind test. The two experimental programs used similar techniques in out-of-pile studies. Highly irradiated fuel samples were heated in radiofrequency induction furnaces to very high temperatures (up to 2700 K at ORNL and 2750 K at CEA) in oxidizing (H{sub 2}O), reducing (H{sub 2}) or mixed (H{sub 2}O+H{sub 2}) environments. The experimental parameters, which were chosen from calculated accident scenarios, did not duplicate specific accidents, but rather emphasized careful control of test conditions to facilitate extrapolation of the results to a wide variety of accident situations. This paper presents a broad and consistent database from ORNL and CEA release results obtained independently since the early 1980`S. A comparison of CORSOR and CORSOR Booth calculations, currently used in safety analysis, and the experimental results is presented and

Shelf Life of Food Products: From Open Labeling to Real-Time Measurements.

Science.gov (United States)

Corradini, Maria G

2018-03-25

The labels currently used on food and beverage products only provide consumers with a rough guide to their expected shelf lives because they assume that a product only experiences a limited range of predefined handling and storage conditions. These static labels do not take into consideration conditions that might shorten a product's shelf life (such as temperature abuse), which can lead to problems associated with food safety and waste. Advances in shelf-life estimation have the potential to improve the safety, reliability, and sustainability of the food supply. Selection of appropriate kinetic models and data-analysis techniques is essential to predict shelf life, to account for variability in environmental conditions, and to allow real-time monitoring. Novel analytical tools to determine safety and quality attributes in situ coupled with modern tracking technologies and appropriate predictive tools have the potential to provide accurate estimations of the remaining shelf life of a food product in real time. This review summarizes the necessary steps to attain a transition from open labeling to real-time shelf-life measurements.

Assessing the Relationship Between Chronic Health Conditions and Productivity Loss Trajectories

Science.gov (United States)

Pranksy, Glenn

2014-01-01

Objective: To examine the relationship between health conditions and the risk for membership in longitudinal trajectories of productivity loss. Methods: Trajectories of productivity loss from the ages of 25 to 44 years, previously identified in the National Longitudinal Survey of Youth (NLSY79), were combined with information on health conditions from the age 40 years health module in the NLSY79. Multinomial logistic regression was used to examine the relative risk of being in the low-risk, early-onset increasing risk, late-onset increasing risk, or high-risk trajectories compared with the no-risk trajectory for having various health conditions. Results: The trajectories with the greatest probability of productivity loss longitudinally had a greater prevalence of the individual health conditions and a greater total number of health conditions experienced. Conclusions: Health conditions are associated with specific longitudinal patterns of experiencing productivity loss. PMID:25479294

Alternative indicators for measuring hospital productivity.

Science.gov (United States)

Serway, G D; Strum, D W; Haug, W F

1987-08-01

This article explores the premise that the appropriateness and usefulness of typical hospital productivity measures have been affected by three changes in delivery: Organizational restructuring and other definition and data source changes that make full-time equivalent employee (FTE) measurements ambiguous. Transition to prospective payment (diagnosis-related groups). Increase in capitation (prepaid, at risk) programs. The effects of these changes on productivity management indicate the need for alternative productivity indicators. Several productivity measures that complement these changes in internal operations and the external hospital business environment are presented. These are based on an analysis of four hospitals within a multihospital system, and an illustration and interpretation of an array of measures, based on ten months of actual data, is provided. In conclusion, the recommendation is made for hospital management to collect an expanded set of productivity measures and review them in light of changing expense and revenue management schemes inherent in new payment modes.

Modifying yeast tolerance to inhibitory conditions of ethanol production processes

Directory of Open Access Journals (Sweden)

Luis eCaspeta

2015-11-01

Full Text Available Saccharomyces cerevisiae strains having a broad range of substrate utilization, rapid substrate consumption and conversion to ethanol, as well as good tolerance to inhibitory conditions are ideal for cost-competitive ethanol production from lignocellulose. A major drawback to directly design S. cerevisiae tolerance to inhibitory conditions of lignocellulosic ethanol production processes is the lack of knowledge about basic aspects of its cellular signaling network in response to stress. Here we highlight the inhibitory conditions found in ethanol production processes, the targeted cellular functions, the key contributions of integrated –omics analysis to reveal cellular stress responses according to these inhibitors, and current status on design-based engineering of tolerant and efficient S. cerevisiae strains for ethanol production from lignocellulose.

Estimating product-to-product variations in metal forming using force measurements

NARCIS (Netherlands)

Havinga, Gosse Tjipke; Van Den Boogaard, Ton

2017-01-01

The limits of production accuracy of metal forming processes can be stretched by the development of control systems for compensation of product-to-product variations. Such systems require the use of measurements from each semi-finished product. These measurements must be used to estimate the final

Optimization of fermentation conditions for red pigment production ...

African Journals Online (AJOL)

An extracellular pigment-producing ascomycetous filamentous fungi belonging to the genera Penicillium was obtained from soil and its optimal culture conditions investigated. The optimal culture conditions for pigment production were as follows; soluble starch 2% (670 units), peptone (880 units), pH 9.0 (900 units); ...

Screening of culture condition for xylanase production by ...

African Journals Online (AJOL)

The study demonstrated not only the importance of the nature of the substrate in obtaining a system resistant to catabolic repression, but also the importance of the culture conditions for biosynthesis of this enzyme. T. viride showed a high potential for xylanase production under the conditions presented in these assays.

MEASURING PRODUCTIVITY OF SOFTWARE DEVELOPMENT TEAMS

Directory of Open Access Journals (Sweden)

Goparaju Purna Sudhakar

2012-02-01

Full Text Available This paper gives an exhaustive literature review of the techniques and models available tomeasure the productivity of software development teams. Definition of productivity, measuringindividual programmer’s productivity, and measuring software development team productivity arediscussed. Based on the literature review it was found that software productivity measurement canbe done using SLOC (Source Lines of Code, function points, use case points, object points, andfeature points. Secondary research findings indicate that the team size, response time, taskcomplexity, team climate and team cohesion have an impact on software development teamproductivity. List of factors affecting the software development team productivity are studied andreviewed.

Relationship between fumonisin production and FUM gene expression in Fusarium verticillioides under different environmental conditions.

Science.gov (United States)

Fanelli, Francesca; Iversen, Anita; Logrieco, Antonio F; Mulè, Giuseppina

2013-01-01

Fusarium verticillioides is the main source of fumonisins, a group of mycotoxins that can contaminate maize-based food and feed and cause diseases in humans and animals. The study of the effect of different environmental conditions on toxin production should provide information that can be used to develop strategies to minimize the risk. This study analysed the effect of temperature (15°C-35°C), water activity (a(w): 0.999-0.93), salinity (0-125 g l(-1) NaCl) and pH (5-8) on the growth and production of fumonisins B(1) (FB1), B(2) (FB2) and B(3) (FB3) and the expression of FUM1 and FUM21 in F. verticillioides. The highest growth rate was measured at 25°C, a(w) of 0.998-0.99 and 0-25 g l(-1) of NaCl. Optimal conditions for fumonisin production were 30°C, a(w) of 0.99, 25 g l(-1) of NaCl and pH 5; nevertheless, the strain showed a good adaptability and was able to produce moderate levels of fumonisins under a wide range of conditions. Gene expression mirrored fumonisin production profile under all conditions with the exception of temperature: FUM1 and FUM21 expression was highest at 15°C, while maximum fumonisin production was at 30°C. These data indicate that a post-transcriptional regulation mechanism could account for the different optimal temperatures for FUM gene expression and fumonisin production.

Measuring and improving productivity in general radiology.

Science.gov (United States)

Wilt, Michelle A; Miranda, Rafael; Johnson, C Daniel; Love, Peggy Sue

2010-10-01

The aim of this study was to determine a method of measuring productivity among general radiographers in a moderate-sized hospital and to improve and sustain productivity within that work area. The average times needed to perform the 13 most common examinations were measured. Performance of the various examinations was tracked and multiplied by the time allocated per procedure; this measure was divided by the length of the work shift to determine productivity. Productivity measures were shared among the work group, and decisions to improve productivity (eg, whether to fill open positions) were made by group members. Average time spent per examination type was calculated (range, 10 minutes to 1 hour 16 minutes). At baseline (February 2008), group productivity was 50%. Productivity increased during the first year of monitoring and was sustained through November 2009 (productivity range, 57%-63%). Yearly savings from not filling open positions were estimated to be $174,000. Productivity in a general radiology work area can be measured. Consensus among the work group helped increase productivity and assess progress. This methodology, if widely adopted, could be standardized and used to compare productivity across departments and institutions. Copyright © 2010 American College of Radiology. Published by Elsevier Inc. All rights reserved.

Primary production measurements at three reservoirs in the state of Sao Paulo, Brazil

International Nuclear Information System (INIS)

Jureidini, P.; Chinez, S.J.; Agudo, E.G.

1983-01-01

Primary production measurements were carried out at three reservoirs in the state of Sao Paulo, Barra Bonita, Paiva Castro and Ponte nova using the 14 C technique. Meanwhile, several physical and chemical parameters of these water were also evaluated, in order to find out the limnological conditions of these reservoirs. Primary production rates ranged from 7,6mg C/m 3 d at Ponte Nova, to 247,2mg C/m 3 d at Barra Bonita. There seems to be god correlation between water quality data and primary production measurements. Regarding the results, it may be stated that the Barra Bonita reservoir has reached the eutrophic level, while the other two exibit mesotrophic levels. As a way of testing the water quality data collected was used in Churchill and Nicholas model, issuing results in agreement with those of the primary production measurements. (Author) [pt

b-Production measurements with ATLAS

International Nuclear Information System (INIS)

Robins, Simon

2001-01-01

The Large Hadron Collider at CERN will produce b-hadrons with unprecedentedly high statistics, and with a higher energy reach than any previous machine. The ATLAS detector will offer excellent acceptance and performance for b physics studies and will make high statistics measurements of b-quark production to probe QCD. ATLAS can contribute to an understanding of the large discrepancy seen between the QCD prediction and Tevatron cross-section measurements. Measurements will be made of the absolute and differential production cross-sections. Measurements of bb-bar correlations will be made to test the NLO contributions to the cross-section and to place limits on non-perturbative effects

Estimating product-to-product variations in metal forming using force measurements

Science.gov (United States)

Havinga, Jos; van den Boogaard, Ton

2017-10-01

The limits of production accuracy of metal forming processes can be stretched by the development of control systems for compensation of product-to-product variations. Such systems require the use of measurements from each semi-finished product. These measurements must be used to estimate the final quality of each product. We propose to predict part of the product-to-product variations in multi-stage forming processes based on force measurements from previous process stages. The reasoning is that final product properties as well as process forces are expected to be correlated since they are both affected by material and process variation. In this study, an approach to construct a moving window process model based on historical data from the process is presented. These regression models can be built and updated in real-time during production. The approach is tested with data from a demonstrator process with cutting, deep drawing and bending stages. It is shown that part of the product-to-product variations in the process can be predicted with the developed process model.

Conditions and strategies for integrating ergonomics into product development

DEFF Research Database (Denmark)

Broberg, Ole

1996-01-01

Ergonomics considerations at the stage of product development in industry is a major strategy for prevention of work-related injuries and illnesses among employees at the time of manufacture of new products. This study elucidates some important conditions and possibilities for integrating...... such considerations during the product development process. Special attention is paid to the role of design and production engineers. Based on different understandings of the product development process four approaches to integration of ergonomics are outlined....

Open and continuous fermentation: products, conditions and bioprocess economy.

Science.gov (United States)

Li, Teng; Chen, Xiang-bin; Chen, Jin-chun; Wu, Qiong; Chen, Guo-Qiang

2014-12-01

Microbial fermentation is the key to industrial biotechnology. Most fermentation processes are sensitive to microbial contamination and require an energy intensive sterilization process. The majority of microbial fermentations can only be conducted over a short period of time in a batch or fed-batch culture, further increasing energy consumption and process complexity, and these factors contribute to the high costs of bio-products. In an effort to make bio-products more economically competitive, increased attention has been paid to developing open (unsterile) and continuous processes. If well conducted, continuous fermentation processes will lead to the reduced cost of industrial bio-products. To achieve cost-efficient open and continuous fermentations, the feeding of raw materials and the removal of products must be conducted in a continuous manner without the risk of contamination, even under 'open' conditions. Factors such as the stability of the biological system as a whole during long cultivations, as well as the yield and productivity of the process, are also important. Microorganisms that grow under extreme conditions such as high or low pH, high osmotic pressure, and high or low temperature, as well as under conditions of mixed culturing, cell immobilization, and solid state cultivation, are of interest for developing open and continuous fermentation processes. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

"Productivity performance measurement - follow-up"

DEFF Research Database (Denmark)

Kristensen, Troels

2008-01-01

The Danish Ministry of Health has published the third annual report on hospital productivity. This experience has contributed to policy goals becoming more detailed and ambitious. New policy goals are: to include hospital productivity measures at less aggregated levels, to include labour producti...... productivity and hospital psychiatric care, to provide web-based solutions that facilitate access to productivity data, and to develop new classifications of hospital levels related to structural reforms....

Calorimetric study on human erythrocyte glycolysis. Heat production in various metabolic conditions.

Science.gov (United States)

Minakami, S; de Verdier, C H

1976-06-01

The heat production of human erythrocytes was measured on a flow microcalorimeter with simultaneous analyses of lactate and other metabolites. The heat production connected with the lactate formation was about 17 kcal (71 kJ) per mol lactate formed which corresponded to the sum of heat production due to the formation of lactate from glucose and the heat production due to neutralization. The heat production rate increased as the pH of the suspension increased, corresponding to the increase in lactate formation. Glycolytic inhibitors such as fluoride and monoiodoacetate caused a decrease in the rate of heat production, whereas arsenate induced a large transient increase in heat production associated with a transient increase in lactate formation. Decrease in pyruvate concentration was usually associated with increase in heat production, although the decreased pyruvate concentration was coupled with formation of 2,3-bisphosphoglycerate. When inosine, dihydroxyacetone or D-glyceraldehyde was used as a substrate, an increase in the heat production rate was observed. Addition of methylene blue caused an oxygen uptake which was accompanied by a remarkable increase in heat production rate corresponding to about 160 kcal (670 kJ) per mol oxygen consumed. The value for heat production in red cells in the above-mentioned metabolic conditions was considered in relation to earlier known data on free energy and enthalpy changes of the different metabolic steps in the glycolytic pathway.

Substantiation of Payment Conditions for Products

Directory of Open Access Journals (Sweden)

I. M. Babuk

2004-01-01

Full Text Available The paper proposes a model that presupposes granting more favorable payment (discount conditions with the purpose to expedite payments for products. Dependence for calculation of discount rate has been deduced on the basis of information about an actual cost of debtor’s accounts receivable. The example of discount calculation depending on a maturity of debtor’s accounts receivable is given in the paper.

Performance Measurement in Global Product Development

DEFF Research Database (Denmark)

Taylor, Thomas Paul; Ahmed-Kristensen, Saeema

2013-01-01

there is a requirement for the process to be monitored and measured relative to the business strategy of an organisation. It was found that performance measurement is a process that helps achieve sustainable business success, encouraging a learning culture within organisations. To this day, much of the research into how...... performance is measured has focussed on the process of product development. However, exploration of performance measurement related to global product development is relatively unexplored and a need for further research is evident. This paper contributes towards understanding how performance is measured...

Measurement of delayed neutron-emitting fission products in nuclear reactor coolant water during reactor operation

International Nuclear Information System (INIS)

Anon.

1981-01-01

The method covers the detection and measurement of delayed neutron-emitting fission products contained in nuclear reactor coolant water while the reactor is operating. The method is limited to the measurement of the delayed neutron-emitting bromine isotope of mass 87 and the delayed neutron-emitting iodine isotope of mass 137. The other delayed neutron-emitting fission products cannot be accurately distinguished from nitrogen 17, which is formed under some reactor conditions by neutron irradiation of the coolant water molecules. The method includes a description of significance, measurement variables, interferences, apparatus, sampling, calibration, standardization, sample measurement procedures, system efficiency determination, calculations, and precision

Optimization of Fermentation Conditions for the Production of Bacteriocin Fermentate

Science.gov (United States)

2015-03-30

FERMENTATION CONDITIONS FOR THE PRODUCTION OF BACTERIOCIN “ FERMENTATE ” by Anthony Sikes Wayne Muller and Claire Lee March 2015...From - To) October 2010 – November 2013 4. TITLE AND SUBTITLE OPTIMIZATION OF FERMENTATION CONDITIONS FOR THE PRODUCTION OF BACTERIOCIN “ FERMENTATE ...nisin and pediocin. Whey + yeast extract was the best performing whey fermentation media. The nisin producer strain Lactococcus. lactis ssp. lactis was

Impact of Work Conditions on Productivity

Directory of Open Access Journals (Sweden)

Anton Petričević

2011-12-01

Full Text Available Every institution should monitor its productivity. If productivity is decreasing, particular measures should be taken. The aim of the paper was to analyse the situation in four institutions by means of questionnaires filled in by 135 respondents, and to point to the problems that were detected through questionnaires. To increase productivity, high levels of worker responsibility should be introduced within the framework of work process, taking into account work potentials of workers, quantity and quality of work. From the results obtained through this survey it was noted that an adequately motivated worker in comfortable work environment is willing to be fully devoted to work and achieve best results, thus ultimately contributing to the overall productivity. There should be a tendency to adequately reward every worker who is willing to commit to work during full working hours and to be responsible for his or her work. Every type of work can be defined by productivity function.

Measurements of Pair Production Under Channelling Conditions by 70-180 GeV Photons Incident on Single Crystals

CERN Multimedia

2002-01-01

This experiment will use the WA69 set-up to deliver a tagged photon beam in the energy range from 15~GeV to 150~GeV with a total angular spread of about @M~0.5~mrad. The incident photon direction is known to about 35~@mrad through the direction of the emitting electron. The photon beam is incident on an about 1~mm thick Ge single crystal in order to investigate pair production in single crystals. Above a certain energy threshold photons incident along crystal axis will show strongly increased pair production yi - the so-called .us Channelling Pair Production (ChPP). The produced pairs are analyzed in the @W-spectrometer. The large spread in incident photon angles offers an excellent opportunity to investigate in one single experiment the pair production in an angular region around a crystal axes and thereby compare ChPP with coherent (CPP) and incoherent (ICPP) processes. The very abrupt onset of ChPP (around threshold) will be measured and give a crucial test of the theoretical calculations. The differential...

Mixotrophic transition induced lipid productivity in Chlorella pyrenoidosa under stress conditions for biodiesel production

Directory of Open Access Journals (Sweden)

Hari Prasad Ratnapuram

2018-01-01

Full Text Available Influence of mixotrophic mode and its transition to various trophic modes under stress conditions was assessed during two stage cultivation of Chlorella pyrenoidosa. Significant lipid productivity was triggered under low light intensity, glucose + bicarbonate supplementation and nitrogen starvation. The association between biomass and lipid productivity, fatty acid composition during mixotrophic transition was critically evaluated. Biomass in growth phase (GP and stress phase (SP was 6.14 g/l and 5.14 g/l, respectively, in mixotrophic mode. Higher lipid productivity of 284 g/kg and 154.3 g/kg of neutral lipids was achieved in SP in mixotrophic-mixotrophic (MM and mixotrophic-heterotrophic (MH modes, respectively. Stress conditions resulted in high unsaturated fatty acid methyl esters in MH mode. In addition, neutral lipid content was 58% in MH and 52% in MM, that can be attributed to carbon source that is supplemented even in stress phase. Exploring such novel strategies can generate sustainable avenues for biodiesel production.

Robust Production Planning in Fashion Apparel Industry under Demand Uncertainty via Conditional Value at Risk

Directory of Open Access Journals (Sweden)

Abderrahim Ait-Alla

2014-01-01

Full Text Available This paper presents a mathematical model for robust production planning. The model helps fashion apparel suppliers in making decisions concerning allocation of production orders to different production plants characterized by different lead times and production costs, and in proper time scheduling and sequencing of these production orders. The model aims at optimizing these decisions concerning objectives of minimal production costs and minimal tardiness. It considers several factors such as the stochastic nature of customer demand, differences in production and transport costs and transport times between production plants in different regions. Finally, the model is applied to a case study. The results of numerical computations are presented. The implications of the model results on different fashion related product types and delivery strategies, as well as the model’s limitations and potentials for expansion, are discussed. Results indicate that the production planning model using conditional value at risk (CVaR as the risk measure performs robustly and provides flexibility in decision analysis between different scenarios.

Research and application of online measurement system of tire tread profile in automobile tire production

Science.gov (United States)

Wang, Pengyao; Chen, Xiangguang; Yang, Kai; Liu, Xuejiao

2017-01-01

To improve the measuring efficiency of width and thickness of tire tread in the process of automobile tire production, the actual condition for the tire production process is analyzed, and a fast online measurement system based on moving tire tread of tire specifications is established in this paper. The coordinate data of tire tread profile is acquired by 3D laser sensor, and we use C# language for programming which is an object-oriented programming language to complete the development of client program. The system with laser sensor can provide real-time display of tire tread profile and the data to require in the process of tire production. Experimental results demonstrate that the measuring precision of the system is <= 1mm, it can meet the measurement requirements of the production process, and the system has the characteristics of convenient installation and testing, system stable operation.

Effects of culture conditions on acetic acid production by bacteria ...

African Journals Online (AJOL)

SARAH

2015-11-30

Nov 30, 2015 ... acid under certain culture conditions similar to cocoa fermentation stress. However ... Keywords: Acetic acid bacteria, acetic acid production, Cocoa fermentation, culture conditions ..... American Society Microbiology Press, pp.

ATLAS measurements of vector boson production

CERN Document Server

Vittori, Camilla; The ATLAS collaboration

2016-01-01

Measurements of the Drell­Yan production of W and Z/gamma* bosons at the LHC provide a benchmark of our understanding of perturbative QCD and probe the proton structure in a unique way. The ATLAS collaboration has performed new high precision measurements at center­of­mass energies of 8 and 13 TeV. In the 8 TeV data, we present recent measurements in the di­lepton mass range up to the TeV scale, double­differentially in dilepton mass and rapidity(­separation). The measurements are compared to state­of­the­art calculations at NNLO in QCD and constrain the photon content of the proton. First precise inclusive measurements of W and Z production at 13 TeV are presented. W/Z and W charge ratios profit from a cancellation of experimental uncertainties. The angular distributions of the Drell­Yan lepton pairs around the Z­boson mass peak probe the underlying QCD dynamic of the Z­boson production mechanisms. We present a measurement of the complete set of angular coefficients describing these distributions...

Can the primary algae production be measured precisely?

International Nuclear Information System (INIS)

Olesen, M.; Lundsgaard, C.

1996-01-01

Algae production in seawater is extremely important as a basic link in marine food chains. Evaluation of the algae quantity is based on 14CO 2 tracer techniques while natural circulation and light absorption in seawater is taken insufficiently into account. Algae production can vary by 500% in similar nourishment conditions, but varying water mixing conditions. (EG)

Application of x-ray residual stress measurement to products

International Nuclear Information System (INIS)

Goto, T.; Iwamura, T.

1975-01-01

The X-ray residual stress measuring method is the only nondestructive method for measuring residual stress in polycrystalline materials. It is capable of obtaining information not only on macroscopic stress but also microscopic stress. The authors are employing this method for the development of pre-service and in-service inspection methods and for the improvement of various manufacturing techniques. In this paper, the results of measurement of some products as examples of its application are described. The examples introduced concern the following: (1) Selection of optimum conditions in heat treatment and stress-relief treatment. (2) Residual stress produced by mechanical processes such as autofrettage and flow form. (3) Check of manufacturing processes of rotary shaft and welded parts. (4) Estimation of fatigue strength of shot-peened part. (5) Detection of fatigue damage of shot-peened part. (auth.)

Light Conditions Affect the Measurement of Oceanic Bacterial Production via Leucine Uptake

Science.gov (United States)

Morán, Xosé Anxelu G.; Massana, Ramon; Gasol, Josep M.

2001-01-01

The effect of irradiance in the range of 400 to 700 nm or photosynthetically active radiation (PAR) on bacterial heterotrophic production estimated by the incorporation of 3H-leucine (referred to herein as Leu) was investigated in the northwestern Mediterranean Sea and in a coastal North Atlantic site, with Leu uptake rates ranging over 3 orders of magnitude. We performed in situ incubations under natural irradiance levels of Mediterranean samples taken from five depths around solar noon and compared them to incubations in the dark. In two of the three stations large differences were found between light and dark uptake rates for the surfacemost samples, with dark values being on average 133 and 109% higher than in situ ones. Data obtained in coastal North Atlantic waters confirmed that dark enclosure may increase Leu uptake rates more than threefold. To explain these differences, on-board experiments of Leu uptake versus irradiance were performed with Mediterranean samples from depths of 5 and 40 m. Incubations under a gradient of 12 to 1,731 μmol of photons m−2 s−1 evidenced a significant increase in incorporation rates with increasing PAR in most of the experiments, with dark-incubated samples departing from this pattern. These results were not attributed to inhibition of Leu uptake in the light but to enhanced bacterial response when transferred to dark conditions. The ratio of dark to light uptake rates increased as dissolved inorganic nitrogen concentrations decreased, suggesting that bacterial nutrient deficiency was overcome by some process occurring only in the dark bottles. PMID:11525969

Fixed target hadron production measurements

CERN Document Server

Panman, J

2009-01-01

The knowledge of light hadron production cross-sections in proton-nucleus interactions is an important prerequisite to the analysis of a wide variety of experiments. One of the important limiting factors for the precision of accelerator based and atmospheric neutrino oscillation experiments is the uncertainty in the composition and spectrum of the neutrino flux. Cosmic-ray experiments detecting extensive air-showers can greatly improve their ability to interpret the data when precise hadron production spectra are available over a large range of energies. Dedicated hadron production experiments have been taking data recently and are now publishing their results. Other experiments have just started their data-taking and plan to supply measurements which can significantly extend the kinematic range in which data will be available. Early measurements at the LHC can extend this range to much higher energies than available up to now. Recent results will be shown and compared with hadronic production models. An outl...

Measurement of Ozone Production Sensor

Directory of Open Access Journals (Sweden)

M. Cazorla

2010-05-01

Full Text Available A new ambient air monitor, the Measurement of Ozone Production Sensor (MOPS, measures directly the rate of ozone production in the atmosphere. The sensor consists of two 11.3 L environmental chambers made of UV-transmitting Teflon film, a unit to convert NO₂ to O₃, and a modified ozone monitor. In the sample chamber, flowing ambient air is exposed to the sunlight so that ozone is produced just as it is in the atmosphere. In the second chamber, called the reference chamber, a UV-blocking film over the Teflon film prevents ozone formation but allows other processes to occur as they do in the sample chamber. The air flows that exit the two chambers are sampled by an ozone monitor operating in differential mode so that the difference between the two ozone signals, divided by the exposure time in the chambers, gives the ozone production rate. High-efficiency conversion of NO₂ to O₃ prior to detection in the ozone monitor accounts for differences in the NO_x photostationary state that can occur in the two chambers. The MOPS measures the ozone production rate, but with the addition of NO to the sampled air flow, the MOPS can be used to study the sensitivity of ozone production to NO. Preliminary studies with the MOPS on the campus of the Pennsylvania State University show the potential of this new technique.

Measuring multifactor productivity growth

Czech Academy of Sciences Publication Activity Database

Wölfl, A.; Hájková, Dana

-, 2007/5 (2007), s. 1-45 Institutional research plan: CEZ:AV0Z70850503 Keywords : multifactor productivity growth * GDP growth * measuring Subject RIV: AH - Economics http://www.oecd.org/dataoecd/61/17/39522985.pdf

A combination of body condition measurements is more informative than conventional condition indices: temporal variation in body condition and corticosterone in brown tree snakes (Boiga irregularis).

Science.gov (United States)

Waye, Heather L; Mason, Robert T

2008-02-01

The body condition index is a common method for quantifying the energy reserves of individual animals. Because good body condition is necessary for reproduction in many species, body condition indices can indicate the potential reproductive output of a population. Body condition is related to glucocorticoid production, in that low body condition is correlated to high concentrations of corticosterone in reptiles. We compared the body condition index and plasma corticosterone levels of brown tree snakes on Guam in 2003 to those collected in 1992/1993 to determine whether that population still showed the chronic stress and poor condition apparent in the earlier study. We also examined the relationship between fat mass, body condition and plasma corticosterone concentrations as indicators of physiological condition of individuals in the population. Body condition was significantly higher in 2003 than in the earlier sample for mature male and female snakes, but not for juveniles. The significantly lower levels of corticosterone in all three groups in 2003 suggests that although juveniles did not have significantly improved energy stores they, along with the mature males and females, were no longer under chronic levels of stress. Although the wet season of 2002 was unusually rainy, low baseline levels of corticosterone measured in 2000 indicate that the improved body condition of snakes in 2003 is likely the result of long-term changes in prey populations rather than annual variation in response to environmental conditions.

Effect of diverse ecological conditions on biomass production of ...

African Journals Online (AJOL)

Kangaroo grass native to Australia is known as the best grass to grow on different environmental and soil conditions. Biomass production of any grass is the key factor to estimate that if the grass could fulfill the animal requirements. Biomass production of kangaroo grass was estimated in this study at three growth stages on ...

Working conditions, health and productivity among dentists in Swedish public dental care - a prospective study during a 5-year period of rationalisation

DEFF Research Database (Denmark)

Rolander, B.; Jonker, D.; Winkel, Jørgen

2013-01-01

' working conditions, health and productivity during a 5-year period. In 2003 and 2008, 65 dentists responded to questionnaires measuring work conditions and health. Treatment times for patients and productivity were tracked in electronic registers. Paired t-tests showed that the number of treated adult...... patients per dentist increased, and perceived physical working conditions improved while perceived work control and leadership deteriorated. Structural equation modelling showed that physical factors were important for health and productivity. When assessing risks in the work environment, there is a need...... to understand the interaction of effects on working conditions and health due to rationalisations so as to increase the sustainability of production systems. Practioner Summary: Dentistry in Sweden has undergone considerable change. Questionnaire surveys with dentists, undertaken in 2003 and 2008, found...

Determination of optimal conditions of oxytetracyclin production from streptomyces rimosus

International Nuclear Information System (INIS)

Zouaghi, Atef

2007-01-01

Streptomyces rimosus is an oxytetracycline (OTC) antibiotic producing bacteria that exhibited activities against gram positive and negative bacteria. OTC is used widely not only in medicine but also in production industry. The antibiotic production of streptomyces covers a very wide range of condition. However, antibiotic producers are particularly fastidious cultivated by proper selection of media such as carbon source. In present study we have optimised conditions of OTC production (Composition of production media, p H, shaking and temperature). The results have been shown that bran barley is the optimal media for OTC production at 28C pH5.8 at 150rpm for 5 days. For antibiotic determination, OTC was extracted with different organic solvent. Thin-layer chromatography system was used for separation and identification of OTC antibiotic. High performance liquid chromatographic (HPLC) method with ultraviolet detection for the analysis of OTC is applied to the determination of OTC purification. (Author). 24 refs

Questionnaire on the measurement condition of distribution coefficient

International Nuclear Information System (INIS)

Takebe, Shinichi; Kimura, Hideo; Matsuzuru, Hideo

2001-05-01

The distribution coefficient is used for various transport models to evaluate the migration behavior of radionuclides in the environment and is very important parameter in environmental impact assessment of nuclear facility. The questionnaire was carried out for the purpose of utilizing for the proposal of the standard measuring method of distribution coefficient. This report is summarized the result of questionnairing on the sampling methods and storage condition, the pretreatment methods, the analysis items in the physical/chemical characteristics of the sample, and the distribution coefficient measuring method and the measurement conditions in the research institutes within country. (author)

Luminosity measurement and beam condition monitoring at CMS

Energy Technology Data Exchange (ETDEWEB)

Leonard, Jessica Lynn [DESY, Zeuthen (Germany)

2015-07-01

The BRIL system of CMS consists of instrumentation to measure the luminosity online and offline, and to monitor the LHC beam conditions inside CMS. An accurate luminosity measurement is essential to the CMS physics program, and measurement of the beam background is necessary to ensure safe operation of CMS. In expectation of higher luminosity and denser proton bunch spacing during LHC Run II, many of the BRIL subsystems are being upgraded and others are being added to complement the existing measurements. The beam condition monitor (BCM) consists of several sets of diamond sensors used to measure online luminosity and beam background with a single-bunch-crossing resolution. The BCM also detects when beam conditions become unfavorable for CMS running and may trigger a beam abort to protect the detector. The beam halo monitor (BHM) uses quartz bars to measure the background of the incoming beams at larger radii. The pixel luminosity telescope (PLT) consists of telescopes of silicon sensors designed to provide a CMS online and offline luminosity measurement. In addition, the forward hadronic calorimeter (HF) will deliver an independent luminosity measurement, making the whole system robust and allowing for cross-checks of the systematics. Data from each of the subsystems will be collected and combined in the BRIL DAQ framework, which will publish it to CMS and LHC. The current status of installation and commissioning results for the BRIL subsystems are given.

Assessment of biogas production from MBT waste under different operating conditions

DEFF Research Database (Denmark)

Pantini, Sara; Verginelli, Jason; Lombardi, Francesco

2015-01-01

In this work, the influence of different operating conditions on the biogas production from mechanically-. biologically treated (MBT) wastes is investigated. Specifically, different lab-scale anaerobic tests varying the water content (26-43% w/w up to 75% w/w), the temperature (from 20 to 25......, the obtained results highlighted that the operative conditions can drastically affect the gas production from MET wastes. This suggests that particular caution should be paid when using the results of lab-scale tests for the evaluation of long-term behaviour expected in the field where the boundary conditions...

Production conditions of bioenergy in Swedish agriculture; Produktionsfoerutsaettningar foer biobraenslen inom svenskt jordbruk

Energy Technology Data Exchange (ETDEWEB)

Boerjesson, Paal

2007-05-15

The overall aim of this report is to analyse and describe the production conditions of bioenergy in Swedish agriculture and how these conditions can vary due to different factors. The conclusion is that the potential for producing bioenergy in Swedish agriculture will vary significantly depending on which energy crops are cultivated, which type of agricultural land is utilised and the geographical location of the production. Furthermore, different crop residues and other by-products from agriculture, utilised for energy purposes, will affect the bioenergy potential. To which extent this physical/biological potential will be utilised in the future depends mainly on economic conditions and financial considerations. These aspects are not included in this study. The report starts with a description of current crop production in Sweden, expressed in energy terms, the energy needed for this production and the regional variation in crop yields. The local variations in cultivation conditions are also analysed, as well as variations over the area of a single farm. Another aspect discussed is the production conditions of energy crops on previous farm land not currently utilised. The report includes an analysis of the potential supply of crop residues and other by-products for energy purposes, such as straw, tops and leaves of sugar beets, manure etc, as well as the regional variation of these residues and by-products. A similar analysis is made of the regional production conditions and potential biomass yields of traditional crops and new energy crops. These analyses also include energy balance calculations showing the energy input needed for different production systems in relation to the harvested biomass yield, and the potential for increased biomass yields in the future. Based on the findings of these various analyses, calculations are made showing some examples of how much bioenergy Swedish agriculture can deliver, depending on how much agricultural land is utilised for

Advanced haptic sensor for measuring human skin conditions

Science.gov (United States)

Tsuchimi, Daisuke; Okuyama, Takeshi; Tanaka, Mami

2010-01-01

This paper is concerned with the development of a tactile sensor using PVDF (Polyvinylidene Fluoride) film as a sensory receptor of the sensor to evaluate softness, smoothness, and stickiness of human skin. Tactile sense is the most important sense in the sensation receptor of the human body along with eyesight, and we can examine skin condition quickly using these sense. But, its subjectivity and ambiguity make it difficult to quantify skin conditions. Therefore, development of measurement device which can evaluate skin conditions easily and objectively is demanded by dermatologists, cosmetic industries, and so on. In this paper, an advanced haptic sensor system that can measure multiple information of skin condition in various parts of human body is developed. The applications of the sensor system to evaluate softness, smoothness, and stickiness of skin are investigated through two experiments.

Beyond Research Productivity: Matching Productivity Measures to Institutional Mission

Directory of Open Access Journals (Sweden)

Patricia Bartholomew

2016-11-01

Full Text Available Aim/Purpose: The aim of this paper is to develop a unified methodology inclusive of the three primary areas of faculty responsibility (teaching, research, and service to calculate departmental productivity that fills the gap in methodological bench-marking tools for overall faculty productivity. Background:\tA disproportionate number of departmental and faculty productivity indices in higher education rely solely on research. Productivity in other areas of faculty workload areas, like teaching and institutional and community service, are either measured separately or ignored all together – even when those activities are institutionally mandated. This does a disservice to those who work in those institutions and skews incentives. Methodology: This paper utilizes a unified methodology inclusive of the three primary areas of faculty responsibility (teaching, research, and service to calculate depart-mental productivity in five disparate departments (English, Biology, Mathematics, Sociology, and Computer Science common to two universities with differing missions (teaching and service. Findings: The results reveal the bias inherent in relying solely on research as a proxy for overall productivity in institutions that have differing missions. Recommendations for Practitioners: Utilizing better metrics informs higher education administrators, promotes better decision-making, and allows incentives to re-align with desired outcomes. Recommendation for Researchers: This paper recommends combing all aspects of faculty workload into a single benchmark index to better measure departmental productivity. Future Research: Further research into improving this simple index is warranted and would include how to account for quality and other facets of productivity.

ATLAS measurements of vector boson production

CERN Document Server

Levchenko, M; The ATLAS collaboration

2014-01-01

ATLAS measurements of vector boson production with associated jets Productions of light and heavy-flavour jets in association with a W or a Z boson in proton-proton collisions are important processes to study QCD in multi-scale environments and the proton parton content. The cross section, differential in several kinematics variables, have been measured with the ATLAS detector in 7 TeV proton-proton collisions and compared to high-order QCD calculations and Monte Carlo simulations. The results demonstrate the need for the inclusion of high-multiplicity matrix elements in the calculations of high jet multiplicities. The ratio of (Z+jets)/(W+jets) provides a precise test of QCD due to the large cancellations of theoretical and experimental uncertainties. Measurement of W+c production cross section has a unique sensitivity to the strange-quark density, which is poorly known at low x. W or Z boson production in association with b-quark jets, on the other hand, probes the b-quark density in the proton and the b-qu...

Measurement and characterization of fission products released from LWR fuel

International Nuclear Information System (INIS)

Osborne, M.F.; Collins, J.L.; Lorenz, R.A.; Norwood, K.S.; Strain, R.V.

1984-01-01

Samples of commercial LWR fuel have been heated under simulated accident conditions to determine the extent and the chemical forms of fission product release. Of the five tests discussed, the fractional releases of Kr, I, and Cs varied from proportional 2% at 1400 0 C to >50% at 2000 0 C; much smaller fractions of Ru, Ag, Sb, and Te were measured in some tests. The major chemical forms in the effluent appeared to include CsI, CsOH, Sb, Te, and Ag. (orig./HP)

Transaction costs and social networks in productivity measurement

DEFF Research Database (Denmark)

Henningsen, Geraldine; Henningsen, Arne; Henning, Christian H. C. A.

2015-01-01

and support. Hence, we use measures of a firm’s access to social networks as a proxy for the transaction costs the firm faces. We develop a microeconomic production model that takes into account transaction costs and networks. Using a data set of 384 Polish farms, we empirically estimate this model......We argue that in the presence of transaction costs, observed productivity measures may in many cases understate the true productivity, as production data seldom distinguish between resources entering the production process and resources of a similar type that are sacrificed for transaction costs....... Hence, both the absolute productivity measures and, more importantly, the productivity ranking will be distorted. A major driver of transaction costs is poor access to information and contract enforcement assistance. Social networks often catalyse information exchange as well as generate trust...

Conditions of viscosity measurement for detecting irradiated peppers

International Nuclear Information System (INIS)

Hayashi, Toru; Todoriki, Setsuko; Okadome, Hiroshi; Kohyama, Kaoru

1995-01-01

Viscosity of gelatinized suspensions of black and white peppers decreased depending upon dose. The viscosity was influenced by gelatinization and viscosity measurement conditions. The difference between unirradiated pepper and an irradiated one was larger at a higher pH and temperature for gelatinization. A viscosity parameter normalized with the starch content of pepper sample and the viscosity of a 5% suspension of corn starch could get rid of the influence of the conditions for viscosity measurement such as type of viscometer, shear rate and temperature. (author)

Conditional approval: Japan lowers the bar for regenerative medicine products.

Science.gov (United States)

Sipp, Douglas

2015-04-02

A new system for conditional approval of regenerative medicine products will allow products of undetermined efficacy to enter the Japanese market. The potential scientific, economic, and ethical implications of this program highlight the need for further discussion and refinement. Copyright © 2015 Elsevier Inc. All rights reserved.

Biological methane production under putative Enceladus-like conditions.

Science.gov (United States)

Taubner, Ruth-Sophie; Pappenreiter, Patricia; Zwicker, Jennifer; Smrzka, Daniel; Pruckner, Christian; Kolar, Philipp; Bernacchi, Sébastien; Seifert, Arne H; Krajete, Alexander; Bach, Wolfgang; Peckmann, Jörn; Paulik, Christian; Firneis, Maria G; Schleper, Christa; Rittmann, Simon K-M R

2018-02-27

The detection of silica-rich dust particles, as an indication for ongoing hydrothermal activity, and the presence of water and organic molecules in the plume of Enceladus, have made Saturn's icy moon a hot spot in the search for potential extraterrestrial life. Methanogenic archaea are among the organisms that could potentially thrive under the predicted conditions on Enceladus, considering that both molecular hydrogen (H 2 ) and methane (CH 4 ) have been detected in the plume. Here we show that a methanogenic archaeon, Methanothermococcus okinawensis, can produce CH 4 under physicochemical conditions extrapolated for Enceladus. Up to 72% carbon dioxide to CH 4 conversion is reached at 50 bar in the presence of potential inhibitors. Furthermore, kinetic and thermodynamic computations of low-temperature serpentinization indicate that there may be sufficient H 2 gas production to serve as a substrate for CH 4 production on Enceladus. We conclude that some of the CH 4 detected in the plume of Enceladus might, in principle, be produced by methanogens.

Why measure radon decay products?

International Nuclear Information System (INIS)

Rolle, R.; Lettner, H.

1997-01-01

Combined development in spectrometry, instrumentation and ventilation modelling with its dependence on short- and long-term weather fluctuations renders possible a new, economical metrology for radon decay products. Short-term measurements can, with few restrictions, be converted to annual exposures of an accuracy superior to that from conventional medium-term Rn gas measurements. (orig.) [de

Preliminary results of the BTF-104 experiment: an in-reactor test of fuel behaviour and fission-product release and transport under LOCA/LOECC conditions

Energy Technology Data Exchange (ETDEWEB)

Dickson, L W; Elder, P H; Devaal, J W; Irish, J D; Yamazaki, A R [Atomic Energy of Canada Ltd., Chalk River, ON (Canada)

1996-12-31

The BTF-104 experiment is one of a series of in-reactor tests being performed to measure fuel behaviour and fission-product release from nuclear fuel subjected to accident conditions. The primary objective of the BTF-104 experiment was to measure fission-product releases from a CANDU-sized fuel element under combined Loss-of-Coolant Accident (LOCA) and Loss-of-Emergency-Core-Cooling (LOECC) conditions at an average fuel temperature of about 1550 deg C. The preliminary results of the BTF-104 experiment are presented in this paper. (author). 6 refs., 12 figs.

Optimization of fermentation conditions for trehalose production by a ...

African Journals Online (AJOL)

user

2012-02-16

Feb 16, 2012 ... The culture conditions for the production of trehalose by Rhodotorula sp. strain were optimized. The optimum ... INTRODUCTION. Trehalose is a ..... Water interplay in trehalose ... In: Prescott DM (Ed.), Methods in Cell Biology.

FRESHWATER FISH FARMING CONDITIONS IN 1999 AND THE PRODUCTION PLAN FOR 2000

Directory of Open Access Journals (Sweden)

Zlatko Homen

2000-09-01

Full Text Available One of the activities of the Ministry of Agriculture and Forestry, Fishery and Mediterranean Agriculture Directorate, i. e. Fishery Directorate to be more specific, is the monitoring of conditions in freshwater fish farming. The objective of this work is to show conditions in freshwater fish farming during 1999. and to provide a production plan for 2000. It will also provide detailed insight into the present conditions in freshwater fish farming and into the production trends of this field. Regarding this issue, the »Questionnaire for the Monitoring of Conditions in Freshwater Fish Farming«, was sent to fish farmers aroud the country data was processed from 22 cap ponds and 13 trout ponds. Roughe estimates of conditions were conducted for 2 fish farms, since they haven’t yet returned the mandatoruy questionnaire, i. e. the necessary data. This work features data on the number of employees in fish farms, as well as their qualifications, on the actual production and distribution of farmed freshwater fish, on the areas where production was conducted and on the overall yield. Fish food, raw materials, used tools and incentive funds paid were also taken into consideration. The difficulties faced in this branch of the economy are also inicated. Compared to 1998, a slight decrease in the number of employees of freshwater fish farms has been recorded. The total number of employees in 1999 was 655, of which 555 were on carp ponds and 100 on trout ponds. Data on the qualifications of employees for 1999 show that most of them were unskilled workers, while highly skilled workers make up a minority in this work force. The total production of freshwater in 1999. amoounted to 6.185,51 tons. Of this amount 5.592,52 tons were warm-water fish specied and 592,99 tons were cold-water fish species. Compared to 1998, production decreased by 4,89 percent. Production for 2000 has been planned to increase by 22,15 percent, i. e. the production quantity is projected

Measuring on-shelf availability of FMCG products

Directory of Open Access Journals (Sweden)

Grubor Aleksandar

2015-01-01

Full Text Available Technological development and the process of globalization influence the increase of customers' awareness. In these circumstances they are becoming more demanding, expecting retailers to offer them the right product at the right time and at the right place. The result is one of the basic tasks of retailers, which reflects in providing an adequate level of product availability in retail stores. In order to prevent the stock-out situation, special attention should be dedicated to its identification and measurement. These operations are very important for establishing and implementing other various measures for increasing product availability and thus sales and competitiveness of retail companies. In this regard, besides theoretical considerations of product availability, we presented the basic methods for its measurement. Also, by using the sample of six Fast Moving Consumer goods categories, we applied the method based on the analysis of POS data. In addition to identifying the out-of-stock rates, we confirmed the results of other studies that product availability varies among different categories and retail stores.

Estimation of Aerodynamic Parameters in Conditions of Measurement

Directory of Open Access Journals (Sweden)

Htang Om Moung

2017-01-01

Full Text Available The paper discusses the problem of aircraft parameter identification in conditions of measurement noises. It is assumed that all the signals involved into the process of identification are subjects to measurement noises, that is measurement random errors normally distributed. The results of simulation are presented which show the relation between the noises standard deviations and the accuracy of identification.

Relationship between fumonisin production and FUM gene expression in Fusarium verticillioides under different environmental conditions

DEFF Research Database (Denmark)

Fanelli, Francesca; Iversen, Anita; Logrieco, Antonio F.

2013-01-01

Fusarium verticillioides is the main source of fumonisins, a group of mycotoxins that can contaminate maize-based food and feed and cause diseases in humans and animals. The study of the effect of different environmental conditions on toxin production should provide information that can be used...... to develop strategies to minimize the risk. This study analysed the effect of temperature (15°C-35°C), water activity (aw: 0.999-0.93), salinity (0-125 g l-1 NaCl) and pH (5-8) on the growth and production of fumonisins B1 (FB1), B2 (FB2) and B3 (FB3) and the expression of FUM1 and FUM21 in F....... verticillioides. The highest growth rate was measured at 25°C, aw of 0.998-0.99 and 0-25 g l-1 of NaCl. Optimal conditions for fumonisin production were 30°C, aw of 0.99, 25 g l-1 of NaCl and pH 5; nevertheless, the strain showed a good adaptability and was able to produce moderate levels of fumonisins under...

Measuring green productivity of country: A generlized metafrontier Malmquist productivity index approach

International Nuclear Information System (INIS)

Yu-Ying Lin, Eugene; Chen, Ping-Yu; Chen, Chi-Chung

2013-01-01

This paper measures environmental productivity in 70 countries over the period 1981–2007. Differences in green (environmental) productivity growth across countries under distinct country specific production frontier are measured using directional distance function model, which incorporates desirable output (GDP) and undesirable output (CO 2 emissions). The metafrontier which envelops the two country groups, developed countries and developing countries, are estimated using balanced panel data for the sample countries over the study period. A parametric method is used to compute technical efficiency change, technical change, and scale efficiency change, which aggregate to the generalized metafrontier Malmquist productivity index. The overall results indicated the two country groups operated under distinct stochastic production frontiers and therefore used different production technologies. It is found that developing countries achieved higher growth in their average environmental productivity relative to the metafrontier. Thus the results coincide with the convergence growth theory

Recruitment and condition of juvenile sandeel on the Faroe shelf in relation to primary production

DEFF Research Database (Denmark)

Eliasen, Kirstin; Reinert, Jákup; Gaard, Eilif

The food of early-life sandeel is dominated by zooplankton, which again depends on primary production. On the Faroe Shelf, measurements of accumulated new primary production and chlorophyll a during spring and summer have been carried out since 1990 and 1997, respectively. Large inter...... availability. We compare the time series from the sandeel 0-group surveys with data on phytoplankton production and biomass. The results confirm that survival and condition of the early-life stages of sandeel on the Faroe Shelf is dependent on the magnitude of the primary production. Although the sandeel......-annual variations in the onset of the spring bloom and its intensity have been observed. Since 1974 juvenile sandeels have been sampled annually on the Faroe shelf. These results also show large variations – both in number and in average length. Here, we investigate the variations in recruitment in relation to food...

Measurements of fusion product emission profiles in tokamaks

International Nuclear Information System (INIS)

Strachan, J.D.; Heidbrink, W.W.; Hendel, H.W.; Lovberg, J.; Murphy, T.J.; Nieschmidt, E.B.; Tait, G.D.; Zweben, S.J.

1986-11-01

The techniques and results of fusion product emission profile measurements are reviewed. While neutron source strength profile measurements have been attempted by several methods, neutron scattering is a limitation to the results. Profile measurements using charged fusion products have recently provided an alternative since collimation is much easier for the charged particles

Measurement of Charmonium Production Cross Section at LHCb

CERN Multimedia

Frosini, M

2010-01-01

The great abundance of charmonium states, collected from the start up of LHC, allows to study its production mechanism. In particular the total and differential $J/\\psi$ production cross section are measured in the transverse momentum range [0;10] GeV/$c$ and in the pseudorapidity range $y \\in$ [2.5;4]. The measurements are performed disentagling the prompt (direct production in $pp$ collisions and feed down from excited charmonium states) and delayed ($b$-hadron decays products) component.

Biosurfactant production using mixed cultures under non-aseptic conditions

International Nuclear Information System (INIS)

Vipulanandan, C.; Ghurye, G.L.; Willson, R.C.

1994-01-01

The use of surfactants is of increasing interest for remediation of petroleum hydrocarbons in groundwater and soil. Surfactants increase the accessibility of adsorbed hydrocarbons and mobilize immiscible petroleum hydrocarbons for treatment. Biosurfactants have the advantage of biodegradability and non-toxicity over their synthetic counterparts, and can be produced from renewable sources. In this study the production of biosurfactant from molasses was investigated in continuously stirred batch reactors. The effects of substrate concentration, yeast extract and peptone on biomass accumulation and biosurfactant production were investigated. Biosurfactant production was quantified by surface tension reduction and critical micelle dilution (CMD). Biosurfactant production was directly correlated with biomass production, and was improved with the addition of yeast extract. Centrifugation of the whole broth reduced surface tension. The performance of the biosurfactant produced from molasses under non-aseptic condition is comparable to other published results

Ceramic production during changing environmental/climatic conditions

Science.gov (United States)

Oestreich, Daniela B.; Glasmacher, Ulrich A.

2015-04-01

Ceramics, with regard to their status as largely everlasting everyday object as well as on the basis of their chronological sensitivity, reflect despite their simplicity the technological level of a culture and therefore also, directly or indirectly, the adaptability of a culture with respect to environmental and/or climatic changes. For that reason the question arises, if it is possible to identify changes in production techniques and raw material sources for ceramic production, as a response to environmental change, e.g. climate change. This paper will present results of a research about Paracas Culture (800 - 200 BC), southern Peru. Through several investigations (e.g. Schittek et al., 2014; Eitel and Mächtle, 2009) it is well known that during Paracas period changes in climate and environmental conditions take place. As a consequence, settlement patterns shifted several times through the various stages of Paracas time. Ceramics from three different sites (Jauranga, Cutamalla, Collanco) and temporal phases of the Paracas period are detailed archaeometric, geochemical and mineralogical characterized, e.g. Raman spectroscopy, XRD, and ICP-MS analyses. The aim of this research is to resolve potential differences in the chemical composition of the Paracas ceramics in space and time and to compare the data with the data sets of pre-Columbian environmental conditions. Thus influences of changing environmental conditions on human societies and their cultural conditions will be discussed. References Eitel, B. and Mächtle, B. 2009. Man and Environment in the eastern Atacama Desert (Southern Peru): Holocene climate changes and their impact on pre-Columbian cultures. In: Reindel, M. & Wagner, G. A. (eds.) New Technologies for Archaeology. Berlin Heidelberg: Springer-Verlag. Schittek, K., Mächtle, B., Schäbitz, F., Forbriger, M., Wennrich, V., Reindel, M., and Eitel, B.. Holocene environmental changes in the highlands of the southern Peruvian Andes (14° S) and their

Ultrasonic Technique for Density Measurement of Liquids in Extreme Conditions

Science.gov (United States)

Kazys, Rymantas; Sliteris, Reimondas; Rekuviene, Regina; Zukauskas, Egidijus; Mazeika, Liudas

2015-01-01

An ultrasonic technique, invariant to temperature changes, for a density measurement of different liquids under in situ extreme conditions is presented. The influence of geometry and material parameters of the measurement system (transducer, waveguide, matching layer) on measurement accuracy and reliability is analyzed theoretically along with experimental results. The proposed method is based on measurement of the amplitude of the ultrasonic wave, reflected from the interface of the solid/liquid medium under investigation. In order to enhance sensitivity, the use of a quarter wavelength acoustic matching layer is proposed. Therefore, the sensitivity of the measurement system increases significantly. Density measurements quite often must be performed in extreme conditions at high temperature (up to 220 °C) and high pressure. In this case, metal waveguides between piezoelectric transducer and the measured liquid are used in order to protect the conventional transducer from the influence of high temperature and to avoid depolarization. The presented ultrasonic density measurement technique is suitable for density measurement in different materials, including liquids and polymer melts in extreme conditions. A new calibration algorithm was proposed. The metrological evaluation of the measurement method was performed. The expanded measurement uncertainty Uρ = 7.4 × 10−3 g/cm3 (1%). PMID:26262619

Ultrasonic Technique for Density Measurement of Liquids in Extreme Conditions.

Science.gov (United States)

Kazys, Rymantas; Sliteris, Reimondas; Rekuviene, Regina; Zukauskas, Egidijus; Mazeika, Liudas

2015-08-07

An ultrasonic technique, invariant to temperature changes, for a density measurement of different liquids under in situ extreme conditions is presented. The influence of geometry and material parameters of the measurement system (transducer, waveguide, matching layer) on measurement accuracy and reliability is analyzed theoretically along with experimental results. The proposed method is based on measurement of the amplitude of the ultrasonic wave, reflected from the interface of the solid/liquid medium under investigation. In order to enhance sensitivity, the use of a quarter wavelength acoustic matching layer is proposed. Therefore, the sensitivity of the measurement system increases significantly. Density measurements quite often must be performed in extreme conditions at high temperature (up to 220 °C) and high pressure. In this case, metal waveguides between piezoelectric transducer and the measured liquid are used in order to protect the conventional transducer from the influence of high temperature and to avoid depolarization. The presented ultrasonic density measurement technique is suitable for density measurement in different materials, including liquids and polymer melts in extreme conditions. A new calibration algorithm was proposed. The metrological evaluation of the measurement method was performed. The expanded measurement uncertainty Uρ = 7.4 × 10(-3) g/cm(3) (1%).

Ultrasonic Technique for Density Measurement of Liquids in Extreme Conditions

Directory of Open Access Journals (Sweden)

Rymantas Kazys

2015-08-01

Full Text Available An ultrasonic technique, invariant to temperature changes, for a density measurement of different liquids under in situ extreme conditions is presented. The influence of geometry and material parameters of the measurement system (transducer, waveguide, matching layer on measurement accuracy and reliability is analyzed theoretically along with experimental results. The proposed method is based on measurement of the amplitude of the ultrasonic wave, reflected from the interface of the solid/liquid medium under investigation. In order to enhance sensitivity, the use of a quarter wavelength acoustic matching layer is proposed. Therefore, the sensitivity of the measurement system increases significantly. Density measurements quite often must be performed in extreme conditions at high temperature (up to 220 °C and high pressure. In this case, metal waveguides between piezoelectric transducer and the measured liquid are used in order to protect the conventional transducer from the influence of high temperature and to avoid depolarization. The presented ultrasonic density measurement technique is suitable for density measurement in different materials, including liquids and polymer melts in extreme conditions. A new calibration algorithm was proposed. The metrological evaluation of the measurement method was performed. The expanded measurement uncertainty Uρ = 7.4 × 10−3 g/cm3 (1%.

Measurement of concentration and size distribution of radon decay products in homes using air cleaners

International Nuclear Information System (INIS)

Montassier, N.; Hopke, P.K.; Shi, Y.; McCallum, B.

1992-01-01

By removing particles, air cleaners can also eliminate radon decay products. However, by removing the particles, the open-quotes unattachedclose quotes fraction of the radon progeny is increased leading to a higher dose per unit exposure. Thus, both the concentration and size distributions of the radon decay products are needed to evaluate air cleaners. Three types of room air cleaners, NO-RAD Radon Removal System, Electronic Air Cleaner and PUREFLOW Air Treatment System were tested in a single family home in Arnprior, Ontario (Canada). Semi-continuous measurements of radon gas concentration and radon decay product activity weighted size distribution were performed in the kitchen/dining room under real living conditions. The effects of air cleaners on both the concentration and size distribution of the radon decay products were measured, and their impact on the dose of radiation given to the lung tissue were examined

ATLAS measurement of Electroweak Vector Boson production

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00453010; The ATLAS collaboration

2017-01-01

The measurements of the Drell-Yan production of W and Z/γ⁎ bosons at the LHC provide a benchmark of our understanding of the perturbative QCD and probe the proton structure in a unique way. The ATLAS collaboration has performed new high precision measurements of the double differential cross-sections as a function of the dilepton mass and rapidity. The measurements are compared to state of calculations at NNLO in QCD and constrain the photon content of the proton. The angular distributions of the Drell-Yan lepton pairs around the Z-boson mass peak probe the underlying QCD dynamics of the Z-boson production mechanisms. The complete set of angular coefficients describing these distributions is presented and compared to theoretical predictions highlighting different approaches of the QCD and EW modelling. First precise inclusive measurements of W and Z production at 13 TeV are presented. $W/Z$ and $W^{+}/W^{−}$ ratios profit from a cancellation of experimental uncertainties.

The behaviour of transport from the fission products caesium and strontium in coated particles for high temperature reactors under irradiation conditions

International Nuclear Information System (INIS)

Zoller, P.

1976-07-01

At first survey is given about existing knowledge of the behaviour of caesium and strontium fission product transport in coated particles. In order to describe the complicated fission product transport mechanisms under irradiation conditions a suitable calculating model (SLIPPER) is taken over and modified to the special problems of an irradiation experiment. Fundamentally, the fission product transport is represented by the two contributions of diffusion and recoil, at which the diffusion is described by effective diffusion coefficients. In difference of that the possibility of a two-phase-diffusion is examined for the Cs diffusion in the fuel kernel. The model application on measuring results from irradiation experiments of KFA-Juelich and Mol-Belgien allowed the explanation from the characteristic of fission product transport in coated particles under irradiation conditions and produced effective diffusion coefficients for the fission products Cs and Sr. (orig.) [de

Optimizing Growth Conditions for Digoxin Production in Digitalis lanata Ehrh

Directory of Open Access Journals (Sweden)

Herman A. van Wietmarschen

2016-08-01

Full Text Available Objective: Digoxin is a therapeutic cardenolide widely used to treat various heart conditions such as atrial flutter, atrial fibrillation and heart failure in both Western as well as Chinese medicine. Digoxin is extracted from cultivated Digitalis lanata Ehrh. plants, known as Mao Hua Yang Di Huang in Chinese medicine. This manuscript presents two studies that were conducted to optimize the cultivation conditions for digoxin production in the TCM Mao Hua Yan Di Huang in a greenhouse under GAP conditions.

ESIAC: A data products system for ERTS imagery (time-lapse viewing and measuring)

Science.gov (United States)

Evans, W. E.; Serebreny, S. M.

1974-01-01

An Electronic Satellite Image Analysis Console (ESIAC) has been developed for visual analysis and objective measurement of earth resources imagery. The system is being employed to process imagery for use by USGS investigators in several different disciplines studying dynamic hydrologic conditions. The ESIAC provides facilities for storing registered image sequences in a magnetic video disc memory for subsequent recall, enhancement, and animated display in monochrome or color. The unique feature of the system is the capability to time-lapse the ERTS imagery and/or analytic displays of the imagery. Data products have included quantitative measurements of distances and areas, brightness profiles, and movie loops of selected themes. The applications of these data products are identified and include such diverse problem areas as measurement of snowfield extent, sediment plumes from estuary dicharge, playa inventory, phreatophyte and other vegetation changes. A comparative ranking of the electronic system in terms of accuracy, cost effectiveness and data output shows it to be a viable means of data analysis.

Measurement and characterization of fission products released from LWR fuel

International Nuclear Information System (INIS)

Osborne, M.F.; Collins, J.L.; Lorenz, R.A.; Norwood, K.S.; Strain, R.V.

1984-01-01

Samples of commercial LWR fuel have been heated under simulated accident conditions to determine the extent and the chemical forms of fission product release. This project was sponsored by the USNRC under a broad program of reactor safety studies. Of the five tests discussed, the fractional releases of Kr, I, and Cs varied from approx. 2% at 1400 0 C to >50% at 2000 0 C; much smaller fractions of Ru, Ag, Sb, and Te were measured in some tests. The major chemical forms in the effluent appeared to include CsI, CsOH, Sb, Te, and Ag

Performance of New and Upgraded Detectors for Luminosity and Beam Condition Measurement at CMS

CERN Document Server

Leonard, Jessica Lynn

2015-01-01

The beam monitoring and luminosity systems of the CMS experiment are enhanced by several new and upgraded sub-detectors to match the challenges of the LHC operation and physics program at increased energy and higher luminosity. A dedicated pixelated luminosity telescope is installed for a fast and precise luminosity measurement. This detector measures coincidences between several three-layer telescopes of silicon pixel detectors to arrive at luminosity for each colliding LHC bunch pair. An upgraded fast beam conditions monitor measures the particle flux using single crystalline diamond sensors. It is equipped with a dedicated front-end ASIC produced in 130 nm CMOS technology. The excellent time resolution is used to separate collision products from machine induced background, thus serving as online luminosity measurement. A new beam-halo monitor at larger radius exploits Cerenkov light from fused silica to provide direction sensitivity and excellent time resolution to separate incoming and outgoing particles....

Influence of synoptic condition and holiday effects on VOCs and ozone production in the Yangtze River Delta region, China

Science.gov (United States)

Xu, Zhengning; Huang, Xin; Nie, Wei; Chi, Xuguang; Xu, Zheng; Zheng, Longfei; Sun, Peng; Ding, Aijun

2017-11-01

Both anthropogenic emission and synoptic conditions play important roles in ozone (O3) formation and accumulation. In order to understand the influence of synoptic condition and holiday effects on ozone production in the Yangtze River Delta region, China, concentrations of speciated volatile organic compounds (VOCs) and O3 as well as other relevant trace gases were simultaneously measured at the Station for Observing Regional Processes of the Earth System (SORPES) in Nanjing around the National Day holidays of China in 2014, which featured substantial change of emissions and dominated by typical anti-cyclones. Different groups of VOC species and their chemical reactivities were comprehensively analyzed. We observed clear diurnal variations of short alkenes during the measurement period, considerable amount of short alkenes were observed during night (more than 10 ppb) while almost no alkenes were measured during daytime, which might be attributed to different chemical processes. The obvious enhancement of the VOC tracers during the National Day holidays (Oct. 1st-Oct. 7th) indicated that the holiday effect strongly influenced the distribution of VOC profile and chemical reactivity in the atmosphere. At the same time, two meso-scale anticyclone processes were also observed during the measurement period. The synoptic condition contributed to the accumulation of VOCs and other precursors, which consequently impacted the ozone production in this region. The integrated influence of synoptic and holiday effects was also analyzed with an Observation Based Model (OBM) based on simplified MCM (Master Chemical Mechanism) chemical mechanism. The calculated relative increment reactivity (RIR) of different VOC groups revealed that during the holidays, this region was in VOC-limited regime and the variation of RIR shows a close linkage to the development and elimination of anti-cyclones, indicating an in-negligible contribution of synoptic effect toward ozone production in this

Optimization of fermentation conditions for ethanol production from whey

Energy Technology Data Exchange (ETDEWEB)

Castillo, F J; Izaguirre, M F; Michelena, V; Moreno, B

1982-01-01

Optimal conditions for ethanol production in 7% whey solutions by the yeast Candida pseudotropicalis ATCC 8619 included an initial pH of 4.57 and 30 degrees. Complete fermentation of the available lactose took place without supplementary nutrients; additions of N and P salts, yeast extract, or corn steep liquor resulted in increased yeast production and lower ethanol yields. A possible correlation was observed between increases in yeast inocula and lactose utilization and ethanol production rates; 8.35 g ethanol/L was obtained within 22 hours by using a yeast inoculum of 13.9 g/L. No differences in fermentation rates or ethanol yields were observed when whole or deproteinized whey solutions were used. Concentrated whey permeates, obtained after removal of the valuable proteins from whey, can be effectively fermented for ethanol production.

Measurement of single top quark production with CMS

CERN Document Server

Andrea, Jeremy

2018-01-01

Several measurements of single top quark production in proton-proton collisions at the LHC at centre-of-mass energies of 7, 8 and 13 TeV, using data collected with the CMS experiment, are presented. The analyses investigate separately the productions of top via t-channel exchange, in association with a W boson (tW) or via the s-channel. Final states with at least one charged lepton and one b-jet are explored to measure inclusive production cross sections. Fiducial and differential cross section measurements in the t-channel are also reported. The measurements can be used to constrain directly the Vtb CKM matrix element by comparing with the most precise standard model theory predictions. Measurements of rare processes involving a top quark and a neutral EWK boson (Z or photon) are also discussed.

High-frequency productivity estimates for a lake from free-water CO2 concentration measurements

Science.gov (United States)

Provenzale, Maria; Ojala, Anne; Heiskanen, Jouni; Erkkilä, Kukka-Maaria; Mammarella, Ivan; Hari, Pertti; Vesala, Timo

2018-04-01

Lakes are important actors in biogeochemical cycles and a powerful natural source of CO2. However, they are not yet fully integrated in carbon global budgets, and the carbon cycle in the water is still poorly understood. In freshwater ecosystems, productivity studies have usually been carried out with traditional methods (bottle incubations, 14C technique), which are imprecise and have a poor temporal resolution. Consequently, our ability to quantify and predict the net ecosystem productivity (NEP) is limited: the estimates are prone to errors and the NEP cannot be parameterised from environmental variables. Here we expand the testing of a free-water method based on the direct measurement of the CO2 concentration in the water. The approach was first proposed in 2008, but was tested on a very short data set (3 days) under specific conditions (autumn turnover); despite showing promising results, this method has been neglected by the scientific community. We tested the method under different conditions (summer stratification, typical summer conditions for boreal dark-water lakes) and on a much longer data set (40 days), and quantitatively validated it comparing our data and productivity models. We were able to evaluate the NEP with a high temporal resolution (minutes) and found a very good agreement (R2 ≥ 0.71) with the models. We also estimated the parameters of the productivity-irradiance (PI) curves that allow the calculation of the NEP from irradiance and water temperature. Overall, our work shows that the approach is suitable for productivity studies under a wider range of conditions, and is an important step towards developing this method so that it becomes more widely used.

Production of native arbuscular mycorrhizal fungi inoculum under different environmental conditions

Directory of Open Access Journals (Sweden)

Yamir Torres-Arias

Full Text Available Abstract In order to obtain an arbuscular mycorrhizal fungi (AMF native inoculum from Sierra de Moa and determine the most appropriate conditions for its big scale production, four light and temperature combinations were tested in three plant species (Calophyllum antillanum, Talipariti elatum and Paspalum notatum. Growth and development parameters, as well as the mycorrhizal functioning of the seedlings were evaluated. The natural light treatment under high temperatures (L-H was the most suitable for the growth and development of the three plant species, showing the highest total biomass values, mainly of root, and a positive root-shoot ratio balance. This treatment also promoted higher values of root mycorrhizal colonization, external mycelium and AMF spore density. A total of 38 AMF species were identified among the plants and environmental conditions tested. Archaeospora sp.1, Glomus sp.5, Glomus brohultii and G. glomerulatum were observed in all the treatments. The L-H condition can be recommended for native inoculum production, as it promotes a better expression of the AM symbiosis and an elevated production of mycorrhizal propagules.

Direct measurement of thermal conductivity in solid iron at planetary core conditions.

Science.gov (United States)

Konôpková, Zuzana; McWilliams, R Stewart; Gómez-Pérez, Natalia; Goncharov, Alexander F

2016-06-02

The conduction of heat through minerals and melts at extreme pressures and temperatures is of central importance to the evolution and dynamics of planets. In the cooling Earth's core, the thermal conductivity of iron alloys defines the adiabatic heat flux and therefore the thermal and compositional energy available to support the production of Earth's magnetic field via dynamo action. Attempts to describe thermal transport in Earth's core have been problematic, with predictions of high thermal conductivity at odds with traditional geophysical models and direct evidence for a primordial magnetic field in the rock record. Measurements of core heat transport are needed to resolve this difference. Here we present direct measurements of the thermal conductivity of solid iron at pressure and temperature conditions relevant to the cores of Mercury-sized to Earth-sized planets, using a dynamically laser-heated diamond-anvil cell. Our measurements place the thermal conductivity of Earth's core near the low end of previous estimates, at 18-44 watts per metre per kelvin. The result is in agreement with palaeomagnetic measurements indicating that Earth's geodynamo has persisted since the beginning of Earth's history, and allows for a solid inner core as old as the dynamo.

Selection of culture medium and conditions for the production of ...

African Journals Online (AJOL)

oyaide

2013-05-15

May 15, 2013 ... improving the productivity and economical benefits in livestock production ... was to improve the yeast biomass production measured as dry cell ... the total livestock population in India was 1708 Million ... Media for culture maintenance and optimization .... which is very economical and efficient source for the.

Aircraft and ground vehicle friction measurements obtained under winter runway conditions

Science.gov (United States)

Yager, Thomas J.

1989-01-01

Tests with specially instrumented NASA B-737 and B-727 aircraft together with several different ground friction measuring devices have been conducted for a variety of runway surface types and wetness conditions. This effort is part of the Joint FAA/NASA Aircraft/Ground Vehicle Runway Friction Program aimed at obtaining a better understanding of aircraft ground handling performance under adverse weather conditions, and defining relationships between aircraft and ground vehicle tire friction measurements. Aircraft braking performance on dry, wet, snow-, and ice-covered runway conditions is discussed together with ground vehicle friction data obtained under similar runway conditions. For the wet, compacted snow- and ice-covered runway conditions, the relationship between ground vehicles and aircraft friction data is identified. The influence of major test parameters on friction measurements such as speed, test tire characteristics, and surface contaminant-type are discussed. The test results indicate that use of properly maintained and calibrated ground vehicles for monitoring runway friction conditions should be encouraged particularly under adverse weather conditions.

Classification of heart valve condition using acoustic measurements

Energy Technology Data Exchange (ETDEWEB)

Clark, G. [Lawrence Livermore National Lab., CA (United States)

1994-11-15

Prosthetic heart valves and the many great strides in valve design have been responsible for extending the life spans of many people with serious heart conditions. Even though the prosthetic valves are extremely reliable, they are eventually susceptible to long-term fatigue and structural failure effects expected from mechanical devices operating over long periods of time. The purpose of our work is to classify the condition of in vivo Bjork-Shiley Convexo-Concave (BSCC) heart valves by processing acoustic measurements of heart valve sounds. The structural failures of interest for Bscc valves is called single leg separation (SLS). SLS can occur if the outlet strut cracks and separates from the main structure of the valve. We measure acoustic opening and closing sounds (waveforms) using high sensitivity contact microphones on the patient`s thorax. For our analysis, we focus our processing and classification efforts on the opening sounds because they yield direct information about outlet strut condition with minimal distortion caused by energy radiated from the valve disc.

Optimum Conditions for Uricase Enzyme Production by Gliomastix gueg

Directory of Open Access Journals (Sweden)

Atalla, M. M.

2009-01-01

Full Text Available Nineteen strains of microorganisms were screened for uricase production. Gliomastix gueg was recognized to produce high levels of the enzyme. The optimum fermentation conditions for uricase production by Gliomastix gueg were examined. Results showed that uric acid medium was the most favorable one, the optimum temperature was at 30ºC, and incubation period required for maximum production was 8 days with aeration level at 150 rpm and at pH 8.0. Sucrose proved to be the best carbon source, uric acid was found to be the best nitrogen source. Both, dipotassium hydrogen phosphate and ferrous chloride as well as some vitamins gave the highest amount of uricase by Gliomastix gueg.

Health-related productivity losses increase when the health condition is co-morbid with psychological distress: findings from a large cross-sectional sample of working Australians.

Science.gov (United States)

Holden, Libby; Scuffham, Paul A; Hilton, Michael F; Ware, Robert S; Vecchio, Nerina; Whiteford, Harvey A

2011-05-31

The health condition of workers is known to impact on productivity outcomes. The relationship between health and productivity is of increasing interest amid the need to increase productivity to meet global financial challenges. Prevalence of psychological distress is also of growing concern in Australia with a two-fold increase in the prevalence of psychological distress in Australia from 1997-2005. We used the cross-sectional data set from the Australian Work Outcomes Research Cost-benefit (WORC) study to explore the impacts of health conditions with and without co-morbid psychological distress, compared to those with neither condition, in a sample of approximately 78,000 working Australians. The World Health Organisation Health and Performance Questionnaire was used which provided data on demographic characteristics, health condition and working conditions. Data were analysed using negative binomial logistic regression and multinomial logistic regression models for absenteeism and presenteeism respectively. For both absenteeism and presenteeism productivity measures there was a greater risk of productivity loss associated when health conditions were co-morbid with psychological distress. For some conditions this risk was much greater for those with co-morbid psychological distress compared to those without. Co-morbid psychological distress demonstrates an increased risk of productivity loss for a range of health conditions. These findings highlight the need for further research to determine whether co-morbid psychological distress potentially exacerbates lost productivity.

Local power production at the end consumer - legal, political and economical external conditions

International Nuclear Information System (INIS)

Grinden, Bjoern; Hunnes, Arngrim; Naesje, Paal; Wangensteen, Ivar; Morch, Andrei Z.

2002-12-01

The report deals with the external conditions for local power production, suggested as a production close to or at the end consumer. The political, legal and economical frame conditions for such production including rating are discussed. The report shall together with a technical report regarding appropriate technologies for such production (A5712), serve as a basis for case studies and monitors later in the project. Through the case studies it will be uncovered how the external conditions are functioning which will make foundations for recommendations concerning possible alterations in the conditions in order to make the local power production more profitable. In the discussion on the political and legal external conditions the system of today is studied. From the political area the general development is described and a short analysis is made of what to expect from case handling procedures, and some challenges are pointed out At present there is a simplified handling of cases of minor and smaller power plants. In order to obtain a more realistic construction of such plants the requirements of license handling may need sharpening. The tariffing of energy deliverance is studied. The regulations for tariffing and income regulation in the distribution network is mainly designed with the consumer and the central power production in mind. A study is made of how the regulations work, to what extent precessions and additional rules are needed and to what extent alterations in the regulations are needed in order to incorporate the local power production in a rational way. While a local power producer at best, will want a price for power which is sold at the power market of the size of 20 oere/kWh, the power will increase in value further down in the voltage level. At the 230 V level the power price will be of the size of 60 oere/kWh all expenses included and the network rent (during normal precipitation conditions). Therefore the production for own consumption will be met

Technological measures to improve automotive product quality

OpenAIRE

Gladkov, V.; Kruglov, S.

2010-01-01

The paper examines the basic technological measures aimed at improving product quality in automotive industry. While paying due attention to solving organizational and technological problems, including the development of certification systems for production processes, it is also necessary to improve the technical standards of specific technologies, equipment and materials as they largely determine product quality. Special emphasis is given to the importance of improving the production of auto...

Thermophysical Properties Measurement of High-Temperature Liquids Under Microgravity Conditions in Controlled Atmospheric Conditions

Science.gov (United States)

Watanabe, Masahito; Ozawa, Shumpei; Mizuno, Akotoshi; Hibiya, Taketoshi; Kawauchi, Hiroya; Murai, Kentaro; Takahashi, Suguru

2012-01-01

Microgravity conditions have advantages of measurement of surface tension and viscosity of metallic liquids by the oscillating drop method with an electromagnetic levitation (EML) device. Thus, we are preparing the experiments of thermophysical properties measurements using the Materials-Science Laboratories ElectroMagnetic-Levitator (MSL-EML) facilities in the international Space station (ISS). Recently, it has been identified that dependence of surface tension on oxygen partial pressure (Po2) must be considered for industrial application of surface tension values. Effect of Po2 on surface tension would apparently change viscosity from the damping oscillation model. Therefore, surface tension and viscosity must be measured simultaneously in the same atmospheric conditions. Moreover, effect of the electromagnetic force (EMF) on the surface oscillations must be clarified to obtain the ideal surface oscillation because the EMF works as the external force on the oscillating liquid droplets, so extensive EMF makes apparently the viscosity values large. In our group, using the parabolic flight levitation experimental facilities (PFLEX) the effect of Po2 and external EMF on surface oscillation of levitated liquid droplets was systematically investigated for the precise measurements of surface tension and viscosity of high temperature liquids for future ISS experiments. We performed the observation of surface oscillations of levitated liquid alloys using PFLEX on board flight experiments by Gulfstream II (G-II) airplane operated by DAS. These observations were performed under the controlled Po2 and also under the suitable EMF conditions. In these experiments, we obtained the density, the viscosity and the surface tension values of liquid Cu. From these results, we discuss about as same as reported data, and also obtained the difference of surface oscillations with the change of the EMF conditions.

Does Input Quality Drive Measured Differences in Firm Productivity?

DEFF Research Database (Denmark)

Fox, Jeremy T.; Smeets, Valerie Anne Rolande

is roughly of the same order of magnitude as some competitive effects found in the literature, but input quality measures do not explain most productivity dispersion, despite economically large production function coefficients. We find that the wage bill explains as much dispersion as human capital measures.......Firms in the same industry can differ in measured productivity by multiples of 3. Griliches (1957) suggests one explanation: the quality of inputs differs across firms. We add labor market history variables such as experience and firm and industry tenure, as well as general human capital measures...

Conditions for Productive Learning in Network Learning Environments

DEFF Research Database (Denmark)

Ponti, M.; Dirckinck-Holmfeld, Lone; Lindström, B.

2004-01-01

are designed without a deep understanding of the pedagogical, communicative and collaborative conditions embedded in networked learning. Despite the existence of good theoretical views pointing to a social understanding of learning, rather than a traditional individualistic and information processing approach......The Kaleidoscope1 Jointly Executed Integrating Research Project (JEIRP) on Conditions for Productive Networked Learning Environments is developing and elaborating conceptual understandings of Computer Supported Collaborative Learning (CSCL) emphasizing the use of cross-cultural comparative......: Pedagogical design and the dialectics of the digital artefacts, the concept of collaboration, ethics/trust, identity and the role of scaffolding of networked learning environments.   The JEIRP is motivated by the fact that many networked learning environments in various European educational settings...

Degradation of materials under conditions of thermochemical cycles for hydrogen production

International Nuclear Information System (INIS)

Klimas, S.J.; Searle, H.; Stolberg, L.

2010-01-01

A capsule method has been developed and employed to measure the degradation rates of selected materials under some of the most challenging conditions relevant to the sulphur-iodine (SI) and the copper-chlorine (Cu-Cl) thermochemical cycles for hydrogen production. The materials tested so far include metals and engineering alloys, structural and functional polymers, elastomers, carbon-based materials, ceramics and glasses, and composites. A number of characterization methods have been used to detect and quantify the degradation of the diverse materials and, when feasible, establish the mode of attack. The paper details the results of this ongoing experimental investigation. The investigation currently focuses on the copper-chlorine hybrid cycle. The environment representative of the conditions in the electrolyser subsystem was approximated with an aqueous solution of hydrochloric acid (13.6 mol/kg), copper(II) chloride (1.36 mol/kg) and copper(I) chloride (1.36 mol/kg) at 160°C and 2.5 MPa (absolute). The current (tentative) recommendations for the selection of the materials required for the construction of the electrolyser subsystem of the copper-chlorine hybrid cycle, and the associated rationale, are presented and discussed. (author)

Using Data Envelopment Analysis to Measure International Agricultural Efficiency and Productivity

OpenAIRE

Arnade, Carlos Anthony

1994-01-01

Numerous methods for measuring multifactor productivity have been used by economists. This report uses a recently developed approach, data envlopment analysis, to measure productivity. This method can be used not only to calculate productivity but also to divide productivity measures into indices that measure technical efficiency and technical change. Technical efficiency measures the efficiency with which resources are used. Technical change measures changes in output arising from improved t...

Use Conditions and Efficiency Measurements of DC Power Optimizers for Photovoltaic Systems: Preprint

Energy Technology Data Exchange (ETDEWEB)

Deline, C.; MacAlpine, S.

2013-10-01

No consensus standard exists for estimating annual conversion efficiency of DC-DC converters or power optimizers in photovoltaic (PV) applications. The performance benefits of PV power electronics including per-panel DC-DC converters depend in large part on the operating conditions of the PV system, along with the performance characteristics of the power optimizer itself. This work presents acase study of three system configurations that take advantage of the capabilities of DC power optimizers. Measured conversion efficiencies of DC-DC converters are applied to these scenarios to determine the annual weighted operating efficiency. A simplified general method of reporting weighted efficiency is given, based on the California Energy Commission's CEC efficiency rating and severalinput / output voltage ratios. Efficiency measurements of commercial power optimizer products are presented using the new performance metric, along with a description of the limitations of the approach.

Resistances to Scientific Knowledge Production of Comparative Measurements of Dropout and Completion in European Higher Education

Science.gov (United States)

Carlhed, Carina

2017-01-01

The article is a critical sociological analysis of current transnational practices on creating comparable measurements of dropout and completion in higher education and the consequences for the conditions of scientific knowledge production on the topic. The analysis revolves around questions of epistemological, methodological and symbolic types…

Device for measuring fission product density

International Nuclear Information System (INIS)

Kaneda, Mitsunori.

1980-01-01

Purpose: To determine the fission product density of xenon or the like and enable measurement of real time of fission product density in a reactor by calculating the disintegration and annihilation of the fission product on the basis of neutron detected output. Constitution: The neutron flux in a reactor is detected by a detector, and applied to first and second density calculators. Second fission product density signal of xenon or the like outputted from first device is again inputted to the device to form an annihilation signal due to disintegration to determine the present density of the second fission product of xenon or the like corresponding to the decrease of the neutron due to the poison of xeron or the like. Similarly, second device determines the first fission product density of iodine or the like. (Sekiya, K.)

Soil physical conditions in Nigerian savannas and biomass production

International Nuclear Information System (INIS)

Salako, F.K.

2004-01-01

Nigeria is located in the tropical zone, with a vast area having savanna vegetation. This is a region that is itself diverse, necessitating a classification into derived savanna, southern Guinea savanna and northern Guinea savanna. These classifications reflect environmental characteristics such as length of growing period, which for instance is 151-180 days for the northern Guinea savanna, 181-210 days for the southern Guinea savanna and 211-270 days for the derived savanna/coastal savanna. The major soils found in the various agro-ecological zones have coarse-textured surface soil, and are low in organic matter and chemical fertility. Although, yields can be improved by addition of inorganic and organic fertilizer, this can only be sustained and assured with high soil physical qualities. Soil physical qualities can be sustained at a high level with conservation tillage and soil conservation measures. Tillage is physical manipulation of the soil. Thus, the most profound effect of tillage is in relation to soil physical properties. For socio-economic and cultural reasons, manual tillage is still widely practiced in Africa as farming is largely at subsistence level. However, there are now a number of commercial farms especially for cash crop production in many parts of Africa. Many of these are located in locations which were hitherto reserved as forest and a need for sustainable production in pertinent to maintain ecological balance. Soils with coarse texture are not often sensitive to some physical parameters while some physical parameters are more relevant in a given study than others. Sustainable crop production researches in the tropics have focused on the role of planted fallows and their spatial arrangement (e.g., as in alley cropping) for many decades. Application of soil physics in the area of food production and environmental management still lags behind other sub-disciplines of soil science, particularly soil fertility in the tropics. A great challenge is

Health-related productivity losses increase when the health condition is co-morbid with psychological distress: findings from a large cross-sectional sample of working Australians

Directory of Open Access Journals (Sweden)

Vecchio Nerina

2011-05-01

Full Text Available Abstract Background The health condition of workers is known to impact on productivity outcomes. The relationship between health and productivity is of increasing interest amid the need to increase productivity to meet global financial challenges. Prevalence of psychological distress is also of growing concern in Australia with a two-fold increase in the prevalence of psychological distress in Australia from 1997-2005. Methods We used the cross-sectional data set from the Australian Work Outcomes Research Cost-benefit (WORC study to explore the impacts of health conditions with and without co-morbid psychological distress, compared to those with neither condition, in a sample of approximately 78,000 working Australians. The World Health Organisation Health and Performance Questionnaire was used which provided data on demographic characteristics, health condition and working conditions. Data were analysed using negative binomial logistic regression and multinomial logistic regression models for absenteeism and presenteeism respectively. Results For both absenteeism and presenteeism productivity measures there was a greater risk of productivity loss associated when health conditions were co-morbid with psychological distress. For some conditions this risk was much greater for those with co-morbid psychological distress compared to those without. Conclusions Co-morbid psychological distress demonstrates an increased risk of productivity loss for a range of health conditions. These findings highlight the need for further research to determine whether co-morbid psychological distress potentially exacerbates lost productivity.

Semi-spontaneous oral text production: measurements in clinical practice.

Science.gov (United States)

Lind, Marianne; Kristoffersen, Kristian Emil; Moen, Inger; Simonsen, Hanne Gram

2009-12-01

Functionally relevant assessment of the language production of speakers with aphasia should include assessment of connected speech production. Despite the ecological validity of everyday conversations, more controlled and monological types of texts may be easier to obtain and analyse in clinical practice. This article discusses some simple measurements for the analysis of semi-spontaneous oral text production by speakers with aphasia. Specifically, the measurements are related to the production of verbs and nouns, and the realization of different sentence types. The proposed measurements should be clinically relevant, easily applicable, and linguistically meaningful. The measurements have been applied to oral descriptions of the 'Cookie Theft' picture by eight monolingual Norwegian speakers, four with an anomic type of aphasia and four without any type of language impairment. Despite individual differences in both the clinical and the non-clinical group, most of the measurements seem to distinguish between speakers with and without aphasia.

Measurements of fission product concentrations in surface air at Bombay, India, during the period 1975-1981

International Nuclear Information System (INIS)

Eapen, C.D.; Rangarajan, C.; Menon, M.R.

1981-01-01

Measurements on airborne fallout radioactivity for the period 1975 up to the middle of 1981 are given. Normally, these measurements are confined to Bombay, but after nuclear tests, some of the other stations where these measurements were carried out in previous years are operated for some time to study the levels of fresh activity. The levels of the long-lived fission products 144 Ce, 106 Ru and 137 Cs, and the short-lived fission products 95 Zr and 140 Ba, were measured, whenever they could be detected following nuclear tests, and tabulated. The data indicate that the activity varies by large factors from tests of similar yield, depending on the meteorological and other conditions. It was determined that the travel time for the Chinese test debris from Lop Nor, China to the West-coast of India is 14 to 16 days

Quadratic measurement and conditional state preparation in an optomechanical system

DEFF Research Database (Denmark)

A. Brawley, George; Vanner, Michael A.; Bowen, Warwick P.

2014-01-01

We experimentally demonstrate, for the first time, quadratic measurement of mechanical motion in an optomechanical system. We use this nonlinear easurement to conditionally prepare classical non-Gaussian states of motion of a micro-mechanical oscillator.......We experimentally demonstrate, for the first time, quadratic measurement of mechanical motion in an optomechanical system. We use this nonlinear easurement to conditionally prepare classical non-Gaussian states of motion of a micro-mechanical oscillator....

Hierarchical Satellite-based Approach to Global Monitoring of Crop Condition and Food Production

Science.gov (United States)

Zheng, Y.; Wu, B.; Gommes, R.; Zhang, M.; Zhang, N.; Zeng, H.; Zou, W.; Yan, N.

2014-12-01

The assessment of global food security goes beyond the mere estimate of crop production: It needs to take into account the spatial and temporal patterns of food availability, as well as physical and economic access. Accurate and timely information is essential to both food producers and consumers. Taking advantage of multiple new remote sensing data sources, especially from Chinese satellites, such as FY-2/3A, HJ-1 CCD, CropWatch has expanded the scope of its international analyses through the development of new indicators and an upgraded operational methodology. The new monitoring approach adopts a hierarchical system covering four spatial levels of detail: global (sixty-five Monitoring and Reporting Units, MRU), seven major production zones (MPZ), thirty-one key countries (including China) and "sub- countries." The thirty-one countries encompass more that 80% of both global exports and production of four major crops (maize, rice, soybean and wheat). The methodology resorts to climatic and remote sensing indicators at different scales, using the integrated information to assess global, regional, and national (as well as sub-national) crop environmental condition, crop condition, drought, production, and agricultural trends. The climatic indicators for rainfall, temperature, photosynthetically active radiation (PAR) as well as potential biomass are first analysed at global scale to describe overall crop growing conditions. At MPZ scale, the key indicators pay more attention to crops and include Vegetation health index (VHI), Vegetation condition index (VCI), Cropped arable land fraction (CALF) as well as Cropping intensity (CI). Together, they characterise agricultural patterns, farming intensity and stress. CropWatch carries out detailed crop condition analyses for thirty one individual countries at the national scale with a comprehensive array of variables and indicators. The Normalized difference vegetation index (NDVI), cropped areas and crop condition are

The biotechnology of hydrogen production by Nostoc flagelliforme grown under chemostat conditions

Energy Technology Data Exchange (ETDEWEB)

Lichtl, R.R.; Bazin, M.J.; Hall, D.O. [Div. of Life Sciences, King`s College, London Univ. (United Kingdom)

1997-11-01

The potential of using N{sub 2}-fixing cyanobacteria to produce hydrogen photobiologically has stimulated research on the physiology and biotechnology of species exhibiting high H{sub 2} production rates over long periods of time. In this work Nostoc flagelliforme, a terrestrial N{sub 2}-fixing cyanobacterium, has been examined to establish its physiology and potential for H{sub 2} production under controlled conditions. Cell filaments of N. flagelliforme were purified and grown in liquid culture to optimize its H{sub 2} metabolism. In batch-grown cultures the activity of nitrogenase, the key enzyme for H{sub 2} production in N{sub 2}-fixing organisms, was found to be high only during a short phase of exponential growth. A chemostat system was thus constructed for long-term experiments using continuous cultures, with the aim of exploiting the exponential growth phase. The dilution rate (D) and environmental factors, such as N{sub 2} concentration in the gas phase and temperature, significantly influenced H{sub 2} production. Cells grown continuously under the optimized conditions of D=0.022 h{sup -1}, 34 C and 5.1 kPa N{sub 2} in the gas phase exhibited H{sub 2} production rates that were more than four times higher than the maximal rates under standard batch growth conditions. (orig.)

Vanillin production using metabolically engineered Escherichia coli under non-growing conditions

Directory of Open Access Journals (Sweden)

Fava Fabio

2007-04-01

Full Text Available Abstract Background Vanillin is one of the most important aromatic flavour compounds used in the food and cosmetic industries. Natural vanillin is extracted from vanilla beans and is relatively expensive. Moreover, the consumer demand for natural vanillin highly exceeds the amount of vanillin extracted by plant sources. This has led to the investigation of other routes to obtain this flavour such as the biotechnological production from ferulic acid. Studies concerning the use of engineered recombinant Escherichia coli cells as biocatalysts for vanillin production are described in the literature, but yield optimization and biotransformation conditions have not been investigated in details. Results Effect of plasmid copy number in metabolic engineering of E. coli for the synthesis of vanillin has been evaluated by the use of genes encoding feruloyl-CoA synthetase and feruloyl hydratase/aldolase from Pseudomonas fluorescens BF13. The higher vanillin production yield was obtained using resting cells of E. coli strain JM109 harbouring a low-copy number vector and a promoter exhibiting a low activity to drive the expression of the catabolic genes. Optimization of the bioconversion of ferulic acid to vanillin was accomplished by a response surface methodology. The experimental conditions that allowed us to obtain high values for response functions were 3.3 mM ferulic acid and 4.5 g/L of biomass, with a yield of 70.6% and specific productivity of 5.9 μmoles/g × min after 3 hours of incubation. The final concentration of vanillin in the medium was increased up to 3.5 mM after a 6-hour incubation by sequential spiking of 1.1 mM ferulic acid. The resting cells could be reused up to four times maintaining the production yield levels over 50%, thus increasing three times the vanillin obtained per gram of biomass. Conclusion Ferulic acid can be efficiently converted to vanillin, without accumulation of undesirable vanillin reduction/oxidation products

Vanillin production using metabolically engineered Escherichia coli under non-growing conditions.

Science.gov (United States)

Barghini, Paolo; Di Gioia, Diana; Fava, Fabio; Ruzzi, Maurizio

2007-04-16

Vanillin is one of the most important aromatic flavour compounds used in the food and cosmetic industries. Natural vanillin is extracted from vanilla beans and is relatively expensive. Moreover, the consumer demand for natural vanillin highly exceeds the amount of vanillin extracted by plant sources. This has led to the investigation of other routes to obtain this flavour such as the biotechnological production from ferulic acid. Studies concerning the use of engineered recombinant Escherichia coli cells as biocatalysts for vanillin production are described in the literature, but yield optimization and biotransformation conditions have not been investigated in details. Effect of plasmid copy number in metabolic engineering of E. coli for the synthesis of vanillin has been evaluated by the use of genes encoding feruloyl-CoA synthetase and feruloyl hydratase/aldolase from Pseudomonas fluorescens BF13. The higher vanillin production yield was obtained using resting cells of E. coli strain JM109 harbouring a low-copy number vector and a promoter exhibiting a low activity to drive the expression of the catabolic genes. Optimization of the bioconversion of ferulic acid to vanillin was accomplished by a response surface methodology. The experimental conditions that allowed us to obtain high values for response functions were 3.3 mM ferulic acid and 4.5 g/L of biomass, with a yield of 70.6% and specific productivity of 5.9 micromoles/g x min after 3 hours of incubation. The final concentration of vanillin in the medium was increased up to 3.5 mM after a 6-hour incubation by sequential spiking of 1.1 mM ferulic acid. The resting cells could be reused up to four times maintaining the production yield levels over 50%, thus increasing three times the vanillin obtained per gram of biomass. Ferulic acid can be efficiently converted to vanillin, without accumulation of undesirable vanillin reduction/oxidation products, using E. coli JM109 cells expressing genes from the ferulic

Supporting Hydrometeorological Research and Applications with Global Precipitation Measurement (GPM) Products and Services

Science.gov (United States)

Liu, Zhong; Ostrenga, D.; Vollmer, B.; Deshong, B.; MacRitchie, K.; Greene, M.; Kempler, S.

2016-01-01

Precipitation is an important dataset in hydrometeorological research and applications such as flood modeling, drought monitoring, etc. On February 27, 2014, the NASA Global Precipitation Measurement (GPM) mission was launched to provide the next-generation global observations of rain and snow (http:pmm.nasa.govGPM). The GPM mission consists of an international network of satellites in which a GPM Core Observatory satellite carries both active and passive microwave instruments to measure precipitation and serve as a reference standard, to unify precipitation measurements from a constellation of other research and operational satellites. The NASA Goddard Earth Sciences (GES) Data and Information Services Center (DISC) hosts and distributes GPM data. The GES DISC is home to the data archive for the GPM predecessor, the Tropical Rainfall Measuring Mission (TRMM). GPM products currently available include the following:1. Level-1 GPM Microwave Imager (GMI) and partner radiometer products2. Goddard Profiling Algorithm (GPROF) GMI and partner products (Level-2 and Level-3)3. GPM dual-frequency precipitation radar and their combined products (Level-2 and Level-3)4. Integrated Multi-satellitE Retrievals for GPM (IMERG) products (early, late, and final run)GPM data can be accessed through a number of data services (e.g., Simple Subset Wizard, OPeNDAP, WMS, WCS, ftp, etc.). A newly released Unified User Interface or UUI is a single interface to provide users seamless access to data, information and services. For example, a search for precipitation products will not only return TRMM and GPM products, but also other global precipitation products such as MERRA (Modern Era Retrospective-Analysis for Research and Applications), GLDAS (Global Land Data Assimilation Systems), etc.New features and capabilities have been recently added in GIOVANNI to allow exploring and inter-comparing GPM IMERG (Integrated Multi-satelliE Retrievals for GPM) half-hourly and monthly precipitation

Influence of product thickness, chamber pressure and heating conditions on production rate of freeze-dried yoghurt

Energy Technology Data Exchange (ETDEWEB)

Sharma, N.K. [G.B. Pant Univ., of Agriculture and Technology (India). Dept. of Mechanical Engineering; Arora, C.P. [Indian Inst. of Tech., New Delhi (India)

1995-06-01

The effects of product thickness, chamber pressure and heating conditions on product temperature profiles and production rate of freeze-dried yoghurt were investigated experimentally. Three sample thicknesses - 3.8 mm, 6.2 mm and 9.4 mm - were tested at chamber pressures of 0.01 and 0.5 mmHg. The production rate increased by decreasing product thickness in contact heating through the bottom of the frozen layer, whereas no significant change was observed in radiant heating. A reduction in chamber pressure from 0.50 to 0.01 mmHg increased the drying time in radiant heating. Maximum production rate was obtained when the thickness of dried product was 6.2 mm, when heat was transferred simultaneously through the frozen and dried layers, and the chamber pressure was at 0.01 mmHg. Use of the product tray developed in this study prevents the growth of dry layers at the contact surfaces. (Author)

Variation in supratentorial cerebrospinal fluid production rate in one day. Measurement by nontriggered phase-contrast magnetic resonance imaging

International Nuclear Information System (INIS)

Takahashi, Hiroto; Tanaka, Hisashi; Fujita, Norihiko; Murase, Kenya; Tomiyama, Noriyuki

2011-01-01

Measuring the cerebrospinal fluid (CSF) production rate is important for understanding the physiology related to normal conditions and neurological disorders. Triggered phase-contrast magnetic resonance imaging (MRI) has been used to measure CSF production rate, but the use of nontriggered phase-contrast MRI has not been reported. The purposes of this study were to assess the feasibility of using nontriggered phase-contrast MRI to measure CSF flow and to determine whether CSF production exhibits circadian rhythm. The feasibility of phase-contrast MRI was assessed with a phantom simulated human cerebral aqueduct. CSF flow through the cerebral aqueduct was measured with nontriggered phase-contrast MRI four times during 1 day in 10 normal volunteers. In the phantom study, linear regression analysis gave the following measured values (ml/h): 0.80 x (value of steady flow)-10.0 for triggered phase-contrast MRI and 1.27 x (value of steady flow)-12.2 for nontriggered phase-contrast MRI. One-factor analysis of variance showed no significant effect of the time of the measurements (P=0.47). The supratentorial CSF production rate was 510±549 ml/day (mean ± SD). Nontriggered phase-contrast MRI provided good estimates of the flow rate in the phantom study. We observed no circadian rhythm in CSF production. (author)

Productivity measurement and growth in Nigeria: challenges and prospects

Directory of Open Access Journals (Sweden)

Chibueze C. IKEJI

2010-12-01

Full Text Available Productivity (growth measurements (describing the assessment of an economy’s rate of change in the ratio of a volume measure of output to a volume measure of input use and related analysis are regular undertakings by staff of economic development of most nations and development institutions such as the OECD. Although they strive to accomplish objectives related to studying efficiency or the achievement of maximum output physically achievable under the use of current technology and given inputs, accounting for the contribution of real costs savings; introduction of benchmarks for production processes and to highlight living standards obtaining at points in time, its emphasis has been at the expense of examination of issues related to society (institutions, history, innovation and productivity change, which are concerned with promoting growth beyond mere productivity accounting. This paper has attempted to address all these issues as they pertain to Nigeria’s rather stagnant or declining economy. This slight modification was prompted by changes from philosophers concerned with the wider area of productivity measurement and change. The literature agrees that productivity measurement (growth accounting only “identified the significance of different proximate sources of growth” but fails to employ institutional, historical case studies to investigate the underlying causes of the growth, innovation and productivity change. Details of deficiencies related to the foregoing issues are examined and policy recommendations drafted and presented to assist practitioners, policy and decision makers and other stakeholders.

Development of plant condition measurement - The Jimah Model

Science.gov (United States)

Evans, Roy F.; Syuhaimi, Mohd; Mazli, Mohammad; Kamarudin, Nurliyana; Maniza Othman, Faiz

2012-05-01

The Jimah Model is an information management model. The model has been designed to facilitate analysis of machine condition by integrating diagnostic data with quantitative and qualitative information. The model treats data as a single strand of information - metaphorically a 'genome' of data. The 'Genome' is structured to be representative of plant function and identifies the condition of selected components (or genes) in each machine. To date in industry, computer aided work processes used with traditional industrial practices, have been unable to consistently deliver a standard of information suitable for holistic evaluation of machine condition and change. Significantly the reengineered site strategies necessary for implementation of this "data genome concept" have resulted in enhanced knowledge and management of plant condition. In large plant with high initial equipment cost and subsequent high maintenance costs, accurate measurement of major component condition becomes central to whole of life management and replacement decisions. A case study following implementation of the model at a major power station site in Malaysia (Jimah) shows that modeling of plant condition and wear (in real time) can be made a practical reality.

Development of plant condition measurement - The Jimah Model

International Nuclear Information System (INIS)

Evans, Roy F; Syuhaimi, Mohd; Mazli, Mohammad; Kamarudin, Nurliyana; Othman, Faiz Maniza

2012-01-01

The Jimah Model is an information management model. The model has been designed to facilitate analysis of machine condition by integrating diagnostic data with quantitative and qualitative information. The model treats data as a single strand of information - metaphorically a 'genome' of data. The 'Genome' is structured to be representative of plant function and identifies the condition of selected components (or genes) in each machine. To date in industry, computer aided work processes used with traditional industrial practices, have been unable to consistently deliver a standard of information suitable for holistic evaluation of machine condition and change. Significantly the reengineered site strategies necessary for implementation of this 'data genome concept' have resulted in enhanced knowledge and management of plant condition. In large plant with high initial equipment cost and subsequent high maintenance costs, accurate measurement of major component condition becomes central to whole of life management and replacement decisions. A case study following implementation of the model at a major power station site in Malaysia (Jimah) shows that modeling of plant condition and wear (in real time) can be made a practical reality.

Experimental measurements of negative hydrogen ion production from surfaces

International Nuclear Information System (INIS)

Graham, W.G.

1977-09-01

Experimental measurements of the production of H - from surfaces bombarded with hydrogen are reviewed. Some measurements of H + and H 0 production from surfaces are also discussed with particular emphasis on work which might be relevant to ion source applications

Measurements of radon exhalation from building materials under model climate conditions

International Nuclear Information System (INIS)

Jann, O.; Schneider, U.; Koeppke, J.; Lehmann, R.

2003-01-01

The inhalation of 222 Rn (radon) is the most important reason for lung cancer as a result of smoking. The cause for enhanced radon concentration in the air of buildings is mostly the building ground. But also building products can lead to increased radon concentrations in indoor air when the products contain raw materials or residues with higher contents of 226 Ra (radium), especially in combination with low air exchange rates. For a realistic estimation of radon concentrations it is helpful to perform emission tests on the basis of emission test chambers. Emissions test chambers are already used successfully for the measurement of volatile organic compounds (VOC) emitted from different materials and products. The analysis of radon in air was performed with a test device based on the principle of ionisation chamber (ATMOS 12 D). It could be show that radon concentrations emitted from building materials can be determined reliably if certain boundary conditions such as temperature, relative humidity and especially area specific air flow rate are met. It was also shown that reduced area specific air flow rates or reduced air exchange rates lead to higher radon concentrations. It is remarkable that no conclusion can be drawn from the activity concentration of radium to the radon concentration in the air. Therefore in some cases much higher radon concentrations in air were determined that had been expected. Obviously diffusion within the material plays an important role. (orig.)

Compatibility of Encore's formosa (Hymenoptera: aphelinidae) with commercial products under laboratory conditions

International Nuclear Information System (INIS)

Barrera Mojica, Jennifer; Carrascal, Jesus Armando; Numa, Stephanie; Rodriguez, Daniel; Cantor, Fernando

2013-01-01

The greenhouse white fly, Trialeurodes vaporariorum one of the major pests of tomatoes under greenhouse conditions, but, it's mainly controlled with chemical insecticides. However, there are alternative control strategies as entomopathogens fungi and parasitoids (Encarsia formosa). In this study we evaluated the compatibility of commercial product with adults and pupae of E. formosa under laboratory conditions. eight treatments were evaluated for adults and pupae of the parasitoid, including two concentrations of the entomopathogenic fungus Beauveria bassiana (5 x 107 and 5 x 109 conidia/ml), commercial doses of four chemical products commonly used to control pests on tomato crops and two controls. These treatments were applied directly on parasitoids, and their mortality rate on adults and pupae were recorded daily. There was no difference in E. formosa pupae among relative with the bacillus thuringiensis products (p > 0.05), indicating that it's compatible with the parasitoid pupae under laboratory conditions. Finally, it was found that products with active ingredients of tiocyclam hidrogenoxalato and B. thuringiensis are incompatibles with E. formosa adults under laboratory conditions.

Standardization of test conditions for gamma camera performance measurement

International Nuclear Information System (INIS)

Jordan, K.

1980-01-01

The actual way of measuring gamma camera performance is to use point sources or flood sources in air, often in combination with bar phantoms. This method mostly brings best performance parameters for cameras but it has nothing in common with the use of a camera in clinical practice. Particular in the case of low energy emitters, like Tc-99m, the influence of scattered radiation over the performance of cameras is very high. Therefore it is important to have test conditions of radionuclide imaging devices, that will approach as best as practicable the measuring conditions in clinical applications. It is therefore a good news that the International Electrochemical Commission IEC has prepared a draft 'Characteristics and test conditions of radionuclide imaging devices' which is now submitted to the national committees for formal approval under the Six Months' Rule. Some essential points of this document are discussed in the paper. (orig.) [de

Conditions for uniqueness of product representations for separable quantum channels and separable quantum states

International Nuclear Information System (INIS)

Cohen, Scott M.

2014-01-01

We give a sufficient condition that an operator sum representation of a separable quantum channel in terms of product operators is the unique product representation for that channel, and then provide examples of such channels for any number of parties. This result has implications for efforts to determine whether or not a given separable channel can be exactly implemented by local operations and classical communication. By the Choi-Jamiolkowski isomorphism, it also translates to a condition for the uniqueness of product state ensembles representing a given quantum state. These ideas follow from considerations concerning whether or not a subspace spanned by a given set of product operators contains at least one additional product operator

Metal complexation in near field conditions of nuclear waste repository - stability constant of copper complexation with cellulose degradation products, in alkaline conditions

International Nuclear Information System (INIS)

Guede, Kipre Bertin

2005-11-01

Copper is a stable element and spent fuel component which constitutes the radioactive waste. The reaction of Copper with cellulose degradation products in alkaline conditions was performed to mimic what occurs in near field conditions of nuclear waste repository. From the characteristics of Cu (II), this thesis aims at inferring the behaviour of radionuclides vis a vis the degradation products of cellulose. The contribution of the present work is therefore the assessment of the stability of the major cellulose degradation product, its affinity for Copper and the extent of the complexation function 13 between Cu (II) and the organic moieties. The formation of cellulose degradation products was followed by measurement of p11, Conductivity, Angle of rotation, relative abundance of aliphatics and aromatics (E4/E6 ) aid by UV-visible spectroscopy. The TOC was determined using the Walkley and Black titration after respectively 31 weeks and 13 weeks of degradation for the reaction mixtures T and A, N. The stability of the major degradation products gave the following figures: ISA(A): - 13 43.39 <ΔG -10639.88 ISA(N): - Ii 436.45<ΔG< -9103.6. The study of the characteristics of Gluconic Acid, as a model compound, was carried out in an attempt to give a general picture of the roper ties of cellulose degradation products. The Complexation between Cu (II) and the organic ligand (Cellulose degradation products) was performed using UV-visible spectroscopy and Ion Distribution technique. The Log B value obtained from the complexation studies at 336 nm for 1 = 0. I Ni NaClO4 and I = 0.01 M NaClO4, falls within a range of 3.48 to 3.74 for the standard reference material (Gluconic Acid), and within I .87 to 2.3 I, and I .6 to 2.01, respectively for the degradation Products ISA (A) and ISA(N). The ion distribution studies showed that: • In (he absence of the degradation product ISA and at pH = 3.68. 56. 17 % of Cu (II) was bound to the resin. • In the presence of ISA and at 2

Validation of the PROMIS® measures of self-efficacy for managing chronic conditions.

Science.gov (United States)

Gruber-Baldini, Ann L; Velozo, Craig; Romero, Sergio; Shulman, Lisa M

2017-07-01

The Patient-Reported Outcomes Measurement Information System ® (PROMIS ® ) was designed to develop, validate, and standardize item banks to measure key domains of physical, mental, and social health in chronic conditions. This paper reports the calibration and validation testing of the PROMIS Self-Efficacy for Managing Chronic Conditions measures. PROMIS Self-Efficacy for Managing Chronic Conditions item banks comprise five domains, Self-Efficacy for Managing: Daily Activities, Symptoms, Medications and Treatments, Emotions, and Social Interactions. Banks were calibrated in 1087 subjects from two data sources: 837 patients with chronic neurologic conditions (epilepsy, multiple sclerosis, neuropathy, Parkinson disease, and stroke) and 250 subjects from an online Internet sample of adults with general chronic conditions. Scores were compared with one legacy scale: Self-Efficacy for Managing Chronic Disease 6-Item scale (SEMCD6) and five PROMIS short forms: Global Health (Physical and Mental), Physical Function, Fatigue, Depression, and Anxiety. The sample was 57% female, mean age = 53.8 (SD = 14.7), 76% white, 21% African American, 6% Hispanic, and 76% with greater than high school education. Full-item banks were created for each domain. All measures had good internal consistency and correlated well with SEMCD6 (r  = 0.56-0.75). Significant correlations were seen between the Self-Efficacy measures and other PROMIS short forms (r  > 0.38). The newly developed PROMIS Self-Efficacy for Managing Chronic Conditions measures include five domains of self-efficacy that were calibrated across diverse chronic conditions and show good internal consistency and cross-sectional validity.

Diffusion modeling of fission product release during depressurized core conduction cooldown conditions

International Nuclear Information System (INIS)

Martin, R.C.

1991-01-01

A simple model for diffusion through the silicon carbide layer of TRISO particles is applied to the data for accident condition testing of fuel spheres for the High-Temperature Reactor program of the Federal Republic of Germany (FRG). Categorization of sphere release of 137 Cs based on fast neutron fluence permits predictions of release with an accuracy comparable to that of the US/FRG accident condition fuel performance model. Calculations are also performed for 85 Kr, 90 Sr, and 110m Ag. Diffusion of cesium through SiC suggests that models of fuel failure should consider fuel performance during repeated accident condition thermal cycling. Microstructural considerations in models of fission product release are discussed. The neutron-induced segregation of silicon within the SiC structure is postulated as a mechanism for enhanced fission product release during accident conditions. As oxygen-enhanced SiC decomposition mechanism is also discussed. (author). 12 refs, 11 figs, 2 tabs

Measurement of Single-top Quark Production with ATLAS Data

CERN Document Server

Holzbauer, J L

2011-01-01

Single-top production processes have been studied using 0.7 fb-1 of data from 7 TeV center-of-mass energy proton-proton collisions collected with the ATLAS detector at the LHC. Single-top is electroweak top production and the standard model includes three production modes. Each contains a Wtb vertex, allowing the possibility of a direct measurement of the CKM matrix element |Vtb|. Single-top could also be sensitive to new physics, such as flavor changing neutral currents or heavy W' bosons. Using cut-based selections, a limit of < 39.1 pb is set for dilepton Wt production and < 26.5 pb for s-channel production. For the t-channel measurement, both cut-based and neural network analyses are performed and the cross-section is measured to be 90 +32 -22 pb, where 65 +28 -19 pb is expected according to standard model.

Issues in Measurement and International Comparison of Productivity - An Overview

NARCIS (Netherlands)

Van Ark, Bart

1996-01-01

This paper reviews recent development in theory and measurement of productivity performance in an international comparative perspective. It emphasises the need for a better link between the theory and practice of measurement, in particular concerning measurement of productivity levels. The paper

A cloud-ozone data product from Aura OMI and MLS satellite measurements

Directory of Open Access Journals (Sweden)

J. R. Ziemke

2017-11-01

Full Text Available Ozone within deep convective clouds is controlled by several factors involving photochemical reactions and transport. Gas-phase photochemical reactions and heterogeneous surface chemical reactions involving ice, water particles, and aerosols inside the clouds all contribute to the distribution and net production and loss of ozone. Ozone in clouds is also dependent on convective transport that carries low-troposphere/boundary-layer ozone and ozone precursors upward into the clouds. Characterizing ozone in thick clouds is an important step for quantifying relationships of ozone with tropospheric H2O, OH production, and cloud microphysics/transport properties. Although measuring ozone in deep convective clouds from either aircraft or balloon ozonesondes is largely impossible due to extreme meteorological conditions associated with these clouds, it is possible to estimate ozone in thick clouds using backscattered solar UV radiation measured by satellite instruments. Our study combines Aura Ozone Monitoring Instrument (OMI and Microwave Limb Sounder (MLS satellite measurements to generate a new research product of monthly-mean ozone concentrations in deep convective clouds between 30° S and 30° N for October 2004–April 2016. These measurements represent mean ozone concentration primarily in the upper levels of thick clouds and reveal key features of cloud ozone including: persistent low ozone concentrations in the tropical Pacific of  ∼ 10 ppbv or less; concentrations of up to 60 pphv or greater over landmass regions of South America, southern Africa, Australia, and India/east Asia; connections with tropical ENSO events; and intraseasonal/Madden–Julian oscillation variability. Analysis of OMI aerosol measurements suggests a cause and effect relation between boundary-layer pollution and elevated ozone inside thick clouds over landmass regions including southern Africa and India/east Asia.

Dosimetric measurement of the disintegration rate of fission products

International Nuclear Information System (INIS)

Solymosi, J.; Nagy, L.G.; Zagyvai, P.

1992-01-01

Investigations on the disintegration rate of fission products of 238 U and 239 Pu are presented. The intensity of the β-and γ-radiation of fission products were measured continously in an interval of 1-1300 hours following the fission, offering the possibility for determining the general and specific characteristics of the individual fission products. A universal measuring procedure was elaborated for the rapid in situ determination of the dosimetric features of fission products, which is suitable for the accurate evaluation and prediction of external absorbed dose even in case of fission products of various origin and unknown composition. (author) 6 refs.; 7 figs.; 1 tab

Measuring Productivity Change without Neoclassical Assumptions: A Conceptual Analysis

NARCIS (Netherlands)

B.M. Balk (Bert)

2008-01-01

textabstractThe measurement of productivity change (or difference) is usually based on models that make use of strong assumptions such as competitive behaviour and constant returns to scale. This survey discusses the basics of productivity measurement and shows that one can dispense with most if not

Optimization of cultural conditions for biosurfactant production by Pleurotus djamor in solid state fermentation.

Science.gov (United States)

Velioglu, Zulfiye; Ozturk Urek, Raziye

2015-11-01

Being eco-friendly, less toxic, more biodegradable and biocompatible, biological surfactants have higher activity and stability compared to synthetic ones. In spite of the fact that there are abundant benefits of biosurfactants over the synthetic congeners, the problem related with the economical and large scale production proceeds. The utilization of several industrial wastes in the production media as substrates reduces the production cost. This current study aims optimization of biosurfactant production conditions by Pleurotus djamor, grown on sunflower seed shell, grape wastes or potato peels as renewable cheap substrates in solid state fermentation. After determination of the best substrate for biosurfactant production, we indicate optimum size and amount of solid substrate, volume of medium, temperature, pH and Fe(2+) concentrations on biosurfactant production. In optimum conditions, by reducing water surface tension to 28.82 ± 0.3 mN/m and having oil displacement diameter of 3.9 ± 0.3 cm, 10.205 ± 0.5 g/l biosurfactant was produced. Moreover, chemical composition of biosurfactant produced in optimum condition was determined by FTIR. Lastly, laboratory's large-scale production was carried out in optimum conditions in a tray bioreactor designed by us and 8.9 ± 0.5 g/l biosurfactant was produced with a significant surface activity (37.74 ± 0.3 mN/m). With its economical suggestions and applicability of laboratory's large-scale production, this work indicates the possibility of using low cost agro-industrial wastes as renewable substrates for biosurfactant production. Therefore, using economically produced biosurfactant will reduce cost in several applications such as bioremediation, oil recovery and biodegradation of toxic chemicals. Copyright © 2015 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

Conditional Standard Errors of Measurement for Scale Scores.

Science.gov (United States)

Kolen, Michael J.; And Others

1992-01-01

A procedure is described for estimating the reliability and conditional standard errors of measurement of scale scores incorporating the discrete transformation of raw scores to scale scores. The method is illustrated using a strong true score model, and practical applications are described. (SLD)

Measuring spatial variation in secondary production and food quality using a common consumer approach in Lake Erie

Science.gov (United States)

Larson, James H.; Richardson, William B.; Evans, Mary Anne; Schaeffer, Jeff; Wynne, Timothy; Bartsch, Michelle; Bartsch, Lynn; Nelson, J. C.; Vallazza, Jon M.

2016-01-01

Lake Erie is a large lake straddling the border of the U.S. and Canada that has become increasingly eutrophic in recent years. Eutrophication is particularly focused in the shallow western basin. The western basin of Lake Erie is hydrodynamically similar to a large estuary, with riverine inputs from the Detroit and Maumee Rivers mixing together and creating gradients in chemical and physical conditions. This study was driven by two questions: How does secondary production and food quality for consumers vary across this large mixing zone? and Are there correlations between cyanobacterial abundance and secondary production or food quality for consumers? Measuring spatial and temporal variation in secondary production and food quality is difficult for a variety of logistical reasons, so here a common consumer approach was used. In a common consumer approach, individuals of a single species are raised under similar conditions until placed in the field across environmental gradients of interest. After some period of exposure, the response of that common consumer is measured to provide an index of spatial variation in conditions. Here, a freshwater mussel (Lampsilis siliquoidea) was deployed at 32 locations that spanned habitat types and a gradient in cyanobacterial abundance in the western basin of Lake Erie to measure spatial variation in growth (an index of secondary production) and fatty acid (FA) content (an index of food quality). We found secondary production was highest within the Maumee rivermouth and lowest in the open waters of the lake. Mussel tissues in the Maumee rivermouth also included more eicosapentaenoic and docosapentaenoic fatty acids (EPA and DPA, respectively), but fewer bacterial FAs, suggesting more algae at the base of the food web in the Maumee rivermouth compared to open lake sites. The satellite-derived estimate of cyanobacterial abundance was not correlated to secondary production, but was positively related to EPA and DPA content in the

LDA measurements under plasma conditions

International Nuclear Information System (INIS)

Lesinski, J.; Mizera-Lesinska, B.; Fanton, J.C.; Boulos, M.I.

1979-01-01

A study was made of the application of Laser Doppler Anemometry (LDA) for the measurement of the fluid and particle velocities under plasma conditions. The flow configuration, is that of a dc plasma jet called the principal jet, in which an alumina powder of a mean particle diameter of 115 μm and a standard deviation of 11.3 μm was injected using a secondary jet. The plasma jet immerged from a 7.1 mm ID nozzle while that of the secondary jet was 2 nm in diameter. The secondary jet was introduced at the nozzle level of the plasma jet directed 90 0 to its axis. Details of the nozzle and the gas flow system are shown in Figure 2

A batch assay to measure microbial hydrogen sulfide production from sulfur-containing solid wastes

International Nuclear Information System (INIS)

Sun, Mei; Sun, Wenjie; Barlaz, Morton A.

2016-01-01

Large volumes of sulfur-containing wastes enter municipal solid waste landfills each year. Under the anaerobic conditions that prevail in landfills, oxidized forms of sulfur, primarily sulfate, are converted to sulfide. Hydrogen sulfide (H 2 S) is corrosive to landfill gas collection and treatment systems, and its presence in landfill gas often necessitates the installation of expensive removal systems. For landfill operators to understand the cost of managing sulfur-containing wastes, an estimate of the H 2 S production potential is needed. The objective of this study was to develop and demonstrate a biochemical sulfide potential (BSP) test to measure the amount of H 2 S produced by different types of sulfur-containing wastes in a relatively fast (30 days) and inexpensive (125 mL serum bottles) batch assay. This study confirmed the toxic effect of H 2 S on both sulfate reduction and methane production in batch systems, and demonstrated that removing accumulated H 2 S by base adsorption was effective for mitigating inhibition. H 2 S production potentials of coal combustion fly ash, flue gas desulfurization residual, municipal solid waste combustion ash, and construction and demolition waste were determined in BSP assays. After 30 days of incubation, most of the sulfate in the wastes was converted to gaseous or aqueous phase sulfide, with BSPs ranging from 0.8 to 58.8 mL H 2 S/g waste, depending on the chemical composition of the samples. Selected samples contained solid phase sulfide which contributed to the measured H 2 S yield. A 60 day incubation in selected samples resulted in 39–86% additional sulfide production. H 2 S production measured in BSP assays was compared with that measured in simulated landfill reactors and that calculated from chemical analyses. H 2 S production in BSP assays and in reactors was lower than the stoichiometric values calculated from chemical composition for all wastes tested, demonstrating the importance of assays to estimate the

High-frequency productivity estimates for a lake from free-water CO2 concentration measurements

Directory of Open Access Journals (Sweden)

M. Provenzale

2018-04-01

Full Text Available Lakes are important actors in biogeochemical cycles and a powerful natural source of CO2. However, they are not yet fully integrated in carbon global budgets, and the carbon cycle in the water is still poorly understood. In freshwater ecosystems, productivity studies have usually been carried out with traditional methods (bottle incubations, 14C technique, which are imprecise and have a poor temporal resolution. Consequently, our ability to quantify and predict the net ecosystem productivity (NEP is limited: the estimates are prone to errors and the NEP cannot be parameterised from environmental variables. Here we expand the testing of a free-water method based on the direct measurement of the CO2 concentration in the water. The approach was first proposed in 2008, but was tested on a very short data set (3 days under specific conditions (autumn turnover; despite showing promising results, this method has been neglected by the scientific community. We tested the method under different conditions (summer stratification, typical summer conditions for boreal dark-water lakes and on a much longer data set (40 days, and quantitatively validated it comparing our data and productivity models. We were able to evaluate the NEP with a high temporal resolution (minutes and found a very good agreement (R2 ≥ 0.71 with the models. We also estimated the parameters of the productivity–irradiance (PI curves that allow the calculation of the NEP from irradiance and water temperature. Overall, our work shows that the approach is suitable for productivity studies under a wider range of conditions, and is an important step towards developing this method so that it becomes more widely used.

Effect of mycorrhizas application on plant growth and nutrient uptake in cucumber production under field conditions

Energy Technology Data Exchange (ETDEWEB)

Ortas, I.

2010-07-01

Mycorrhizas application in horticultural production in the Eastern Mediterranean region of Turkey has been studied under field conditions for several years. The effects of different arbuscular mycorrhizal fungi (AMF) have been evaluated under field conditions for cucumber production. The parameters measured were seedling survival, plant growth and yield, and root colonization. In 1998 and 1999, Glomus mosseae and Glomus etunicatum inoculated cucumber seedlings were treated with and without P (100 kg P2O5 ha-1) application. A second experiment was set up to evaluate the response of cucumber to the inoculation with a consortia of indigenous mycorrhizae, G. mosseae, G. etunicatum, Glomus clarum, Glomus caledonium and a mixture of these four species. Inoculated and control non inoculated cucumber seedlings were established under field conditions in 1998, 2001, 2002 and 2004. Seedling quality, seedling survival under field conditions and yield response to mycorrhiza were tested. Fruits were harvested periodically; at blossom, plant leaves and root samples were taken for nutrient content and mycorrhizal colonization analysis respectively. The field experiment results showed that mycorrhiza inoculation significantly increased cucumber seedling survival, fruit yield, P and Zn shoot concentrations. Indigenous mycorrhiza inoculum was successful in colonizing plant roots and resulted in better plant growth and yield. The relative effectiveness of each of the inocula tested was not consistent in the different experiments, although inoculated plants always grew better than control no inoculated. The most relevant result for growers was the increased survival of seedlings. (Author) 20 refs.

Transaction costs and social networks in productivity measurement

DEFF Research Database (Denmark)

Henningsen, Geraldine; Henningsen, Arne; Henning, Christian H. C. A.

2015-01-01

. Hence, both the absolute productivity measures and, more importantly, the productivity ranking will be distorted. A major driver of transaction costs is poor access to information and contract enforcement assistance. Social networks often catalyse information exchange as well as generate trust...... and support. Hence, we use measures of a firm’s access to social networks as a proxy for the transaction costs the firm faces. We develop a microeconomic production model that takes into account transaction costs and networks. Using a data set of 384 Polish farms, we empirically estimate this model...... and compare different parametric, semiparametric, and nonparametric model specifications. Our results generally support our hypothesis. Especially, large trading networks and dense household networks have a positive influence on a farm’s productivity. Furthermore, our results indicate that transaction costs...

Integral measurements of neutron production in spallation targets

International Nuclear Information System (INIS)

Frehaut, J.; Deneuville, D.; Ledoux, X.; Lochard, J.P.; Longuet, J.L.; Petibon, E.; Alrick, K.; Bownan, D.; Cverna, F.; King, N.S.P.; Morgan, G.L.; Greene, G.; Hanson, A.; Snead, L.; Thompson, R.; Ward, T.

1998-01-01

Measurements of neutron production for thick iron, tungsten and lead targets of different diameter prototypic for spallation systems have been made at SATURNE in an incident proton energy range from 400 MeV to 2 GeV. TIERCE code system calculations are in good agreement with experiment for iron and large diameter tungsten and lead targets. They overestimate the measured neutron production for tungsten and lead targets for diameter ≤20 cm. (author)

PRODUCTION OF WIRE RML OF SQUARE PROFILE IN CONDITIONS OF BELORUSSIAN METALLURGICAL WORKS

Directory of Open Access Journals (Sweden)

D. G. Sachava

2010-01-01

Full Text Available It is shown that at using of profile (square wire RML in conditions of RUP «BMZ» for production of pipes of high pressure their production is cheapened, what attracts interest of consumer.

Ultraviolet Fluorescence LiDAR (UFL as a Measurement Tool for Water Quality Parameters in Turbid Lake Conditions

Directory of Open Access Journals (Sweden)

Heiko Balzter

2013-09-01

Full Text Available Despite longstanding contributions to oceanography, similar use of fluorescence light detection and ranging (LiDAR in lake settings is not routine. The potential for ship-mounted, multispectral Ultraviolet Fluorescence LiDAR (UFL to provide rapid, high-resolution data in variably turbid and productive lake conditions are investigated here through a series of laboratory tank and field measurements carried out on Lake Balaton, Hungary. UFL data, calibrated empirically to a set of coinciding conventionally-analyzed samples, provide simultaneous estimates of three important parameters-chlorophyll a(chla, total suspended matter (TSM and colored dissolved organic matter (CDOM. Successful UFL retrievals from both laboratory and field measurements were achieved for chla (0.01–378 mg∙m−3; R = 0.83–0.92, TSM (0.1–130 g∙m−3; R = 0.90–0.96 and CDOM (0.003–0.125 aCDOM(440; R = 0.80–0.97. Fluorescence emission at 685 nm is shown through tank measurements to display robust but distinct relationships with chla concentration for the two cultured algae species investigated (cyanobacteria, Cylindrospermopsis raciborskii, and chlorophyta, Scenedesmus armatus. The ratio between fluorescence emissions measured at 650 nm, related to the phycocyanin fluorescence maximum, to that at 685 nm is demonstrated to effectively distinguish these two species. Validation through both laboratory measurements and field measurements confirmed that site specific calibration is necessary. This study presents the first known assessment and application of ship-mounted fluorescence LiDAR in freshwater lake conditions and demonstrates the use of UFL in measuring important water quality parameters despite the more complicated hydro-optic conditions of inland waters.

Estimating back to front ratio of wire screen for measurement of thoron decay products

International Nuclear Information System (INIS)

Koli, Amruta; Khandare, Pallavi; Joshi, Manish; Mariam; Khan, Arshad; Sapra, B.K.

2016-01-01

Wire screens are widely used for measuring the fine fraction of radon/thoron decay products. Their capture efficiencies are generally defined at low aerosol concentration conditions as well as at low sampling flow rates. Effect of changes in sampling flow rate and aerosol concentration on wire screen capture efficiencies and counting correction factor has been studied in this work. Controlled experiments have been conducted using two different mesh sizes at two different aerosol concentration conditions. Experimental results were compared with the existing theories for capture efficiencies of wire screens given by Cheng and Yeh (1980) and Alonso et al. (2001); and semi empirical relation for the front to total ratio given by Solomon and Ren (1992). Theoretical predictions have been found to be relatively close to the experimental findings for moderate aerosol conditions but disagreement was observed in case of high aerosol concentration. The possible reasons for these differences have been discussed in this work. - Highlights: • Effect of Fiber Reynolds number on capture efficiency and back to front ratio of wire screen. • Experiments with Thoron decay products at moderate and elevated aerosol concentrations. • Comparison with theoretical estimates. • Fair agreement observed for moderate aerosol concentration.

Degradation of the pharmaceuticals diclofenac and sulfamethoxazole and their transformation products under controlled environmental conditions

International Nuclear Information System (INIS)

Poirier-Larabie, S.; Segura, P.A.; Gagnon, C.

2016-01-01

Contamination of the aquatic environment by pharmaceuticals via urban effluents is well known. Several classes of drugs have been identified in waterways surrounding these effluents in the last 15 years. To better understand the fate of pharmaceuticals in ecosystems, degradation processes need to be investigated and transformation products must be identified. Thus, this study presents the first comparative study between three different natural environmental conditions: photolysis and biodegradation in aerobic and anaerobic conditions both in the dark of diclofenac and sulfamethoxazole, two common drugs present in significant amounts in impacted surface waters. Results indicated that degradation kinetics differed depending on the process and the type of drug and the observed transformation products also differed among these exposure conditions. Diclofenac was nearly degraded by photolysis after 4 days, while its concentration only decreased by 42% after 57 days of exposure to bacteria in aerobic media and barely 1% in anaerobic media. For sulfamethoxazole, 84% of the initial concentration was still present after 11 days of exposure to light, while biodegradation decreased its concentration by 33% after 58 days of exposure under aerobic conditions and 5% after 70 days of anaerobic exposure. In addition, several transformation products were observed and persisted over time while others degraded in turn. For diclofenac, chlorine atoms were lost primarily in the photolysis, while a redox reaction was promoted by biodegradation under aerobic conditions. For sulfamethoxazole, isomerization was favored by photolysis while a redox reaction was also favored by the biodegradation under aerobic conditions. To summarize this study points out the occurrence of different transformation products under variable degradation conditions and demonstrates that specific functional groups are involved in the tested natural attenuation processes. Given the complexity of environmental

Degradation of the pharmaceuticals diclofenac and sulfamethoxazole and their transformation products under controlled environmental conditions

Energy Technology Data Exchange (ETDEWEB)

Poirier-Larabie, S. [Aquatic Contaminants Research Division, Science and Water Technology Directorate, Environment Canada, Montréal, Québec H2Y 2E7 (Canada); Segura, P.A. [Department of Chemistry, Université de Sherbrooke, Sherbrooke, Québec J1K 2R1 (Canada); Gagnon, C., E-mail: christian.gagnon@canada.ca [Aquatic Contaminants Research Division, Science and Water Technology Directorate, Environment Canada, Montréal, Québec H2Y 2E7 (Canada)

2016-07-01

Contamination of the aquatic environment by pharmaceuticals via urban effluents is well known. Several classes of drugs have been identified in waterways surrounding these effluents in the last 15 years. To better understand the fate of pharmaceuticals in ecosystems, degradation processes need to be investigated and transformation products must be identified. Thus, this study presents the first comparative study between three different natural environmental conditions: photolysis and biodegradation in aerobic and anaerobic conditions both in the dark of diclofenac and sulfamethoxazole, two common drugs present in significant amounts in impacted surface waters. Results indicated that degradation kinetics differed depending on the process and the type of drug and the observed transformation products also differed among these exposure conditions. Diclofenac was nearly degraded by photolysis after 4 days, while its concentration only decreased by 42% after 57 days of exposure to bacteria in aerobic media and barely 1% in anaerobic media. For sulfamethoxazole, 84% of the initial concentration was still present after 11 days of exposure to light, while biodegradation decreased its concentration by 33% after 58 days of exposure under aerobic conditions and 5% after 70 days of anaerobic exposure. In addition, several transformation products were observed and persisted over time while others degraded in turn. For diclofenac, chlorine atoms were lost primarily in the photolysis, while a redox reaction was promoted by biodegradation under aerobic conditions. For sulfamethoxazole, isomerization was favored by photolysis while a redox reaction was also favored by the biodegradation under aerobic conditions. To summarize this study points out the occurrence of different transformation products under variable degradation conditions and demonstrates that specific functional groups are involved in the tested natural attenuation processes. Given the complexity of environmental

Monitoring of transcriptional regulation in Pichia pastoris under protein production conditions

Directory of Open Access Journals (Sweden)

Bhattacharyya Anamitra

2007-06-01

Full Text Available Abstract Background It has become evident that host cells react to recombinant protein production with a variety of metabolic and intrinsic stresses such as the unfolded protein response (UPR pathway. Additionally, environmental conditions such as growth temperature may have a strong impact on cell physiology and specific productivity. However, there is little information about the molecular reactions of the host cells on a genomic level, especially in context to recombinant protein secretion. For the first time, we monitored transcriptional regulation of a subset of marker genes in the common production host Pichia pastoris to gain insights into the general physiological status of the cells under protein production conditions, with the main focus on secretion stress related genes. Results Overexpression of the UPR activating transcription factor Hac1p was employed to identify UPR target genes in P. pastoris and the responses were compared to those known for Saccharomyces cerevisiae. Most of the folding/secretion related genes showed similar regulation patterns in both yeasts, whereas genes associated with the general stress response were differentially regulated. Secretion of an antibody Fab fragment led to induction of UPR target genes in P. pastoris, however not to the same magnitude as Hac1p overproduction. Overexpression of S. cerevisiae protein disulfide isomerase (PDI1 enhances Fab secretion rates 1.9 fold, but did not relief UPR stress. Reduction of cultivation temperature from 25°C to 20°C led to a 1.4-fold increase of specific product secretion rate in chemostat cultivations, although the transcriptional levels of the product genes (Fab light and heavy chain were significantly reduced at the lower temperature. A subset of folding related genes appeared to be down-regulated at the reduced temperature, whereas transcription of components of the ER associated degradation and the secretory transport was enhanced. Conclusion Monitoring of

Measurement of beauty production from dimuon events at HERA

International Nuclear Information System (INIS)

2009-01-01

Beauty production in events containing two muons in the final state has been measured with the ZEUS detector at HERA using an integrated luminosity of 114 pb -1 . A low transverse-momentum threshold for muon identification, in combination with the large rapidity coverage of the ZEUS muon system, gives access to almost the full phase space for beauty production. The total cross section for beauty production in ep collisions at (s) 1/2 = 318 GeV has been measured to be σ tot (ep → b b-bar X) = 13.9 ± 1.5(stat.) +4.0 -4.3 (syst.) nb. Differential cross sections and a measurement of b b-bar correlations are also obtained, and compared to other beauty cross-section measurements, Monte Carlo models and next-to-leading-order QCD predictions.

Air-water flow measurement for ERVC conditions by LIF/PIV

International Nuclear Information System (INIS)

Yoon, Jong Woong; Jeong, Yong Hoon

2016-01-01

Critical heat flux (CHF) of the external reactor vessel wall is a safety limit that indicate the integrity of the reactor vessel during the situation. Many research conducted CHF experiments in the IVR-ERVC conditions. However, the flow velocity field which is an important factor in the CHF mechanism were not studied enough in the IVR-ERVC situations. In this study, flow measurements including velocity vector field and the liquid velocity in the IVR-ERVC conditions were studied. The air-water two phase flow loop simulating IVRERVC conditions was set up and liquid velocity field was measured by LIF/PIV technique in this study. The experiment was conducted with and without air injection conditions. For the air-water flow experiment, liquid velocity at the outside of two phase boundary layer became higher and the two phase boundary layer thickness became smaller when the mass flux increases. The velocity data obtained in this study are expected to improve the CHF correlation in the IVR-ERVC situations.

Air-water flow measurement for ERVC conditions by LIF/PIV

Energy Technology Data Exchange (ETDEWEB)

Yoon, Jong Woong; Jeong, Yong Hoon [KAIST, Daejeon (Korea, Republic of)

2016-05-15

Critical heat flux (CHF) of the external reactor vessel wall is a safety limit that indicate the integrity of the reactor vessel during the situation. Many research conducted CHF experiments in the IVR-ERVC conditions. However, the flow velocity field which is an important factor in the CHF mechanism were not studied enough in the IVR-ERVC situations. In this study, flow measurements including velocity vector field and the liquid velocity in the IVR-ERVC conditions were studied. The air-water two phase flow loop simulating IVRERVC conditions was set up and liquid velocity field was measured by LIF/PIV technique in this study. The experiment was conducted with and without air injection conditions. For the air-water flow experiment, liquid velocity at the outside of two phase boundary layer became higher and the two phase boundary layer thickness became smaller when the mass flux increases. The velocity data obtained in this study are expected to improve the CHF correlation in the IVR-ERVC situations.

Time-resolved Shielded-Pickup Measurements and Modeling of Beam Conditioning Effects on Electron Cloud Buildup at CesrTA

CERN Document Server

Crittenden, J A; Liu, X; Palmer, M A; Santos, S; Sikora, J P; Kato, S; Calatroni, S; Rumolo, G

2012-01-01

The Cornell Electron Storage Ring Test Accelerator program includes investigations into electron cloud buildup in vacuum chambers with various coatings. Two 1.1-mlong sections located symmetrically in the east and west arc regions are equipped with BPM-like pickup detectors shielded against the direct beam-induced signal. They detect cloud electrons migrating through an 18-mm-diameter pattern of 0.76 mm-diameter holes in the top of the chamber. A digitizing oscilloscope is used to record the signals, providing time-resolved information on cloud development. We present new measurements of the effect of beam conditioning on a newly-installed amorphous carbon coated chamber, as well as on an extensively conditioned chamber with a diamond-like carbon coating. The ECLOUD modeling code is used to quantify the sensitivity of these measurements to model parameters, differentiating between photoelectron and secondary-electron production processes.

Assessment of productivity loss in air-conditioned buildings using PMV index

Energy Technology Data Exchange (ETDEWEB)

Kosonen, R. [Halton OY, Kausala (Finland); Tan, F. [CapitaLand Commercial Limited, Singapore (Singapore)

2004-07-01

This theoretical study reports on the assessment of productivity loss in air-conditioned office buildings using the PMV approach and makes use of Wyon's reviews [D.P. Wyon, P.O. Fanger, B.W. Olesen, C.J.K. Pedersen, The mental performance of subjects clothed for comfort at two different air temperatures, Ergonomics 18 (1975) 358-374; D.P. Wyon, Individual microclimate control: required range, probable benefits and current feasibility, in: Proceedings of Indoor Air '96, Institute of Public Health, Tokyo, 1996; D.P. Wyon, Indoor environmental effects on productivity. IAQ 96 Paths to better building environments/Keynote address. Y. Kevin. Atlanta, ASHRAE, pp. 5-15] as the basis to compare and to relate how the productivity loss could be minimised through improved thermal comfort design criteria. The finding shows that task-related performance is significantly correlated with the human perception of thermal environment that in turn is dependent on temperatures. Different combinations of thermal criteria (air velocity, clo, metabolic, etc.) can lead to similar PMV value and the PMV equation is useful to predict productivity loss that is due to the rate of change in thermal conditions. The study also highlights the issues that remain to be resolved in future research. (author)

Release of fission products and post-pile creep behaviour of irradiated fuel rods stored under dry conditions

International Nuclear Information System (INIS)

Kaspar, G.; Peehs, M.; Bokelmann, R.; Jorde, D.; Schoenfeld, H.; Haas, W.; Bleier, A.; Rutsch, F.

1985-06-01

The release of moisture and fission products (Kr-85, H-3 and I-129) under dry storage conditions has been examined on six fuel rods which have become defective in the reactor. During the examinations, inert conditions prevailed and limited air inlet was allowed temporarily. The storage temperature was 400 0 C. The residual moisture content of the fuel rods was approx. 5 g. At the beginning of the test, the total moisture content and 0,05% (max.) of the fission gas inventory were released. Under inert conditions, fission gas was not released during a prolonged period of time. Under oxidizing conditions, however, fission gas was released in the course of UO 2 oxidation. Post-pile creep of Zircaloy cladding tubes was measured at temperatures between 350 and 395 0 C and interval gauge pressures between 69 and 110 bar. The creep curves indicate that the irradiated cladding tube specimens still bear internal residual stresses which contribute through their relaxation to the post-pile creep. (orig.) [de

Upgraded Fast Beam Conditions Monitor for CMS online luminosity measurement

CERN Document Server

Leonard, Jessica Lynn; Hempel, Maria; Henschel, Hans; Karacheban, Olena; Lange, Wolfgang; Lohmann, Wolfgang; Novgorodova, Olga; Penno, Marek; Walsh, Roberval; Dabrowski, Anne; Guthoff, Moritz; Loos, R; Ryjov, Vladimir; Burtowy, Piotr; Lokhovitskiy, Arkady; Odell, Nathaniel; Przyborowski, Dominik; Stickland, David P; Zagozdzinska, Agnieszka

2014-01-01

The CMS beam condition monitoring subsystem BCM1F during LHC Run I consisted of 8 individual diamond sensors situated around the beam pipe within the tracker detector volume, for the purpose of fast monitoring of beam background and collision products. Effort is ongoing to develop the use of BCM1F as an online bunch-by-bunch luminosity monitor. BCM1F will be running whenever there is beam in LHC, and its data acquisition is independent from the data acquisition of the CMS detector, hence it delivers luminosity even when CMS is not taking data. To prepare for the expected increase in the LHC luminosity and the change from 50 ns to 25 ns bunch separation, several changes to the system are required, including a higher number of sensors and upgraded electronics. In particular, a new real-time digitizer with large memory was developed and is being integrated into a multi-subsystem framework for luminosity measurement. Current results from Run II preparation will be discussed, including results from the January 201...

Continuous fermentative hydrogen production from cheese whey wastewater under thermophilic anaerobic conditions

Energy Technology Data Exchange (ETDEWEB)

Azbar, Nuri; Cetinkaya Dokgoez, F. Tuba; Keskin, Tugba; Korkmaz, Kemal S.; Syed, Hamid M. [Bioengineering Department, Faculty of Engineering, Ege University, EBILTEM, Bornova, 35100 Izmir (Turkey)

2009-09-15

Hydrogen (H{sub 2}) production from cheese processing wastewater via dark anaerobic fermentation was conducted using mixed microbial communities under thermophilic conditions. The effects of varying hydraulic retention time (HRT: 1, 2 and 3.5 days) and especially high organic load rates (OLR: 21, 35 and 47 g chemical oxygen demand (COD)/l/day) on biohydrogen production in a continuous stirred tank reactor were investigated. The biogas contained 5-82% (45% on average) hydrogen and the hydrogen production rate ranged from 0.3 to 7.9 l H{sub 2}/l/day (2.5 l/l/day on average). H{sub 2} yields of 22, 15 and 5 mmol/g COD (at a constant influent COD of 40 g/l) were achieved at HRT values of 3.5, 2, and 1 days, respectively. On the other hand, H{sub 2} yields were monitored to be 3, 9 and 6 mmol/g COD, for OLR values of 47, 35 and 21 g COD/l/day, when HRT was kept constant at 1 day. The total measurable volatile fatty acid concentration in the effluent (as a function of influent COD) ranged between 118 and 27,012 mg/l, which was mainly composed of acetic acid, iso-butyric acid, butyric acid, propionic acid, formate and lactate. Ethanol and acetone production was also monitored from time to time. To characterize the microbial community in the bioreactor at different HRTs, DNA in mixed liquor samples was extracted immediately for PCR amplification of 16S RNA gene using eubacterial primers corresponding to 8F and 518R. The PCR product was cloned and subjected to DNA sequencing. The sequencing results were analyzed by using MegaBlast available on NCBI website which showed 99% identity to uncultured Thermoanaerobacteriaceae bacterium. (author)

Determination of optimal conditions of oxytetracyclin production from streptomyces rimosus; Optimisation de la production de l'oxytetracycline par Streptomyces rimosus

Energy Technology Data Exchange (ETDEWEB)

Zouaghi, Atef [Institut National des Sciences Appliquees et de Technologie (Tunisia)

2007-07-01

Streptomyces rimosus is an oxytetracycline (OTC) antibiotic producing bacteria that exhibited activities against gram positive and negative bacteria. OTC is used widely not only in medicine but also in production industry. The antibiotic production of streptomyces covers a very wide range of condition. However, antibiotic producers are particularly fastidious cultivated by proper selection of media such as carbon source. In present study we have optimised conditions of OTC production (Composition of production media, p H, shaking and temperature). The results have been shown that bran barley is the optimal media for OTC production at 28C pH5.8 at 150rpm for 5 days. For antibiotic determination, OTC was extracted with different organic solvent. Thin-layer chromatography system was used for separation and identification of OTC antibiotic. High performance liquid chromatographic (HPLC) method with ultraviolet detection for the analysis of OTC is applied to the determination of OTC purification. (Author). 24 refs.

Trends in the market of poultry production in the conditions of globalization

Directory of Open Access Journals (Sweden)

Kyryliuk O.F.

2017-12-01

Full Text Available according to the author, in modern conditions of globalization of food markets, the researching the state of the domestic market of poultry products in order to provide the population with high-grade food products is important. It is established that the formation of demand in the poultry market is mainly due to production by domestic producers, while imports for the period under review are being reduced and meet mainly the needs of processing industry enterprises.

Measures for Increasing of Company’s Production Capacity

Directory of Open Access Journals (Sweden)

Ernesta Žikevičiūtė

2012-07-01

Full Text Available Production capacity improvements are poorly explored areas of economic literature and the existing methods are difficult to apply. For this reason, the organization has only a superficial analysis of capacity, but after all this time, each production company had to improve the production capacity for the market economy and the most economical use of production factors.This article explores the company’s production capacity for better use of tools. It also presents the capacity of their concept, establishment, evaluates the factors leading to their production capacity, for developing efficiency measures and model presentation.Article in Lithuanian

Phasor Measurement Unit under Interference Conditions

DEFF Research Database (Denmark)

Ghiga, Radu; Martin, Kenneth E.; Wu, Qiuwei

2017-01-01

interference condition scenarios. In the first scenario, noise is added to the PMU input signal. The test runs a sweep of Signalto-Noise Ratios (SNR) and the accuracy versus the noise level is obtained. The second scenario injects multiple harmonics with the input to test the influence on accuracy. The last...... scenario focuses on instrument transformer saturation which leads to a modified waveform injected in the PMU. This test goes through different levels of Current Transformer (CT) saturation and analyzes the effect of saturation on the accuracy of PMUs. The test results show PMU measurements will be degraded...

Control of polysilicon on-film particulates with on-product measurements

Science.gov (United States)

Barker, Judith B.; Chain, Elizabeth E.; Plachecki, Vincent E.

1997-08-01

Historically, a number of in-line particle measurements have been performed on separate test wafers included with product wafers during polysilicon processes. By performing film thickness and particulate measurements directly on product wafers, instead, a number of benefits accrue: (1) reduced test wafer usage, (2) reduced test wafer storage requirements, (3) reduced need for equipment to reclaim test wafers, (4) reduced need for direct labor to reclaim test wafers, and (5) reduced engineering 'false alarms' due to incorrectly processed test wafers. Implementation of on-product measurements for the polysilicon diffusion process required a number of changes in both philosophy and methodology. We show the necessary steps to implementation of on-product particle measurements with concern for overall manufacturing efficiency and the need to maintain appropriate control. Particle results from the Tencor 7600 Surfscan are presented.

Measurement of beauty production from dimuon events at HERA

Energy Technology Data Exchange (ETDEWEB)

Chekanov, S.; Derrick, M.; Magill, S. [Argonne National Laboratory, Argonne, IL (United States)] (and others)

2008-09-15

Beauty production in events containing two muons in the final state has been measured with the ZEUS detector at HERA using an integrated luminosity of 114 pb{sup -1}. A low transverse-momentum threshold for muon identification, in combination with the large rapidity coverage of the ZEUS muon system, gives access to almost the full phase space for beauty production. The total cross section for beauty production in ep collisions at {radical}(s) = 318 GeV has been measured to be {sigma}{sub tot}(ep {yields} b anti bX) = 13.9 {+-} 1.5(stat.){sub -4.3}{sup +4.0}(syst.) nb. Differential cross sections and a measurement of b anti b correlations are also obtained, and compared to other beauty cross-section measurements, Monte Carlo models and next-to-leading-order QCD predictions. (orig.)

Production of extracellular chitinase Beauveria bassiana under submerged fermentation conditions

Science.gov (United States)

Elawati, N. E.; Pujiyanto, S.; Kusdiyantini, E.

2018-05-01

Chitinase-producing microbes have attracted attention as one of the potential agents for control of phytopathogenic fungi and insect pests. The fungus that potentially produces chitinase is Beauveria bassiana. This study aims to determine the growth curve and chitinase activities of B. bassiana isolated from Helopeltis antonii insects after application. Method of measuring growth curve was done by dry cell period method, while for measurement of enzyme activity done by measuring absorbance at spectrophotometer. The results showed optimum growth time of B. bassiana with the highest cell count of 0.031 g on day 4 which was log phase, while the highest enzyme activity was 0,585 U / mL on the 4th day for 7 days incubation. Based on these results when correlated growth with enzyme production, chitinase enzyme products are produced in log phase and categorized as primary metabolism.

Conditions of milk production of family farms located in the municipality of Alegre – ES, Brazil

Directory of Open Access Journals (Sweden)

Francisca Carvalho Nascimento Neta

2015-12-01

Full Text Available The present study aimed to assess the conditions and practices of production of raw milk used by farmers, as well as the conditions of storage and of the facilities and structures of the locations of the four collective cooling tanks, in the municipality of Alegre – ES. Data on sanitization procedures and physical structure of barns, source and treatment of water, hygiene practices and health status of milkers, udder cleaning and disinfection procedures and sanitary control of the herd was collected. The physical structure of the locations of the tanks was also assessed. The barns were ventilated, protected from moisture and had covers, and few had cemented floor and milking parlor. A low percentage of producers performed pre (21% and post (6% dipping procedures. Only 1/4 of the farmers used the mug test. All equipment and tools were washed after milking, but few farmers (5% used sanitizers and 94% of the farms used untreated water. Only 8% of the milkers had the habit of washing their hands before milking, and 9% of them were aware of IN 62 regulation of the Ministry of Agriculture, Livestock and Supply. None of the facilities had protection against the entrance of insects, rodents and environmental contaminants. They were poorly sized, did not allow the application of adequate sanitary measures and sanitary conditions were deficient. The high level of nonconformities regarding good manufacturing practices for milk production reinforced the need for the implementation of Good Agricultural Practices in rural farms for the purpose of obtaining milk produced according to the quality standards, preventing losses and ensuring the sustainability of dairy production in the region.

Development of an instrument for direct ozone production rate measurements: measurement reliability and current limitations

Science.gov (United States)

Sklaveniti, Sofia; Locoge, Nadine; Stevens, Philip S.; Wood, Ezra; Kundu, Shuvashish; Dusanter, Sébastien

2018-02-01

Ground-level ozone (O3) is an important pollutant that affects both global climate change and regional air quality, with the latter linked to detrimental effects on both human health and ecosystems. Ozone is not directly emitted in the atmosphere but is formed from chemical reactions involving volatile organic compounds (VOCs), nitrogen oxides (NOx = NO + NO2) and sunlight. The photochemical nature of ozone makes the implementation of reduction strategies challenging and a good understanding of its formation chemistry is fundamental in order to develop efficient strategies of ozone reduction from mitigation measures of primary VOCs and NOx emissions. An instrument for direct measurements of ozone production rates (OPRs) was developed and deployed in the field as part of the IRRONIC (Indiana Radical, Reactivity and Ozone Production Intercomparison) field campaign. The OPR instrument is based on the principle of the previously published MOPS instrument (Measurement of Ozone Production Sensor) but using a different sampling design made of quartz flow tubes and a different Ox (O3 and NO2) conversion-detection scheme composed of an O3-to-NO2 conversion unit and a cavity attenuated phase shift spectroscopy (CAPS) NO2 monitor. Tests performed in the laboratory and in the field, together with model simulations of the radical chemistry occurring inside the flow tubes, were used to assess (i) the reliability of the measurement principle and (ii) potential biases associated with OPR measurements. This publication reports the first field measurements made using this instrument to illustrate its performance. The results showed that a photo-enhanced loss of ozone inside the sampling flow tubes disturbs the measurements. This issue needs to be solved to be able to perform accurate ambient measurements of ozone production rates with the instrument described in this study. However, an attempt was made to investigate the OPR sensitivity to NOx by adding NO inside the instrument

Transformation of soil and vegetable conditions at oil production territories

Science.gov (United States)

Gatina, Evgeniia

2017-04-01

On the territory of modern oil production soil, vegetation, ecosystem conditions of the environment are significantly transformed. Researches have been conducted on the oil production territories located in a boreal coniferous forest natural zone from 2005 to 2015. Standard geobotanical and soil methods are used. Mechanical destruction of a plant cover, change of the water conditions, intake of oil products and salty waters in ecosystems, pollution of the atmosphere are considered as the major technology-related factors defining transformation of land ecosystems at operation of the oil field. Under the mechanical destruction of a plant cover the pioneer plant communities are formed. These communities are characterized by most reduced specific wealth with prevalence of types of meadow groups of plants and presence of types of wetland groups of plants. The biodiversity of biocenosis which are affected linear infrastructure facilities of oil production territories and change of the water conditions, decreases. It is observed decrease in species wealth, simplification of structure of communities. Under the salting of soils in ecosystems there is a decrease species diversity of communities to prevalence nitrophilous and meadow plant species. At the increased content of organic substances in the soils that is a consequence of intake of oil products, is characteristic increase in specific richness of communities, introduction of types of wetland and oligotrophic groups of plants in forest communities. Influence depends on distance to an influence source. In process of removal from a source of atmospheric pollution in forest communities there is a decrease in species diversity and complication of structure of community. It is caused by introduction of types of meadow groups of plants in ecotone sites of the forest communities located near a source of influence and restoration of structural features of forest communities in process of removal from an influence source

Changes in production efficiency in China identification and measuring

CERN Document Server

Xu, Bing; Watada, Junzo

2014-01-01

Evaluating  Production Efficiency in China examines production from engineering and statistics perspectives rather than from economics and mathematics perspectives. The authors present an observable benchmark as the criterion of the production efficiency to replace the unobservable production frontier surface. This book discusses several different computing technologies, controllable variable as a path of identification, changes in production efficiency by decision making on specific operating conditions, and optimal resource allocation. The book provides a channel to tap inside the success stories of China, exploiting the way of changes in production efficiency during China’s development in the past 30 years. This book examines the concepts and realization of production efficiencies across all areas of the economy. Also the book provides the perspective of foreign direct investment (FDI) absorption to identify how Chinese economy changes in production efficiency.

Evaluation of body condition score measured throughout lactation as an indicator of fertility in dairy cattle.

Science.gov (United States)

Banos, G; Brotherstone, S; Coffey, M P

2004-08-01

Body condition score (BCS) records of primiparous Holstein cows were analyzed both as a single measure per animal and as repeated measures per sire of cow. The former resulted in a single, average, genetic evaluation for each sire, and the latter resulted in separate genetic evaluations per day of lactation. Repeated measure analysis yielded genetic correlations of less than unity between days of lactation, suggesting that BCS may not be the same trait across lactation. Differences between daily genetic evaluations on d 10 or 30 and subsequent daily evaluations were used to assess BCS change at different stages of lactation. Genetic evaluations for BCS level or change were used to estimate genetic correlations between BCS measures and fertility traits in order to assess the capacity of BCS to predict fertility. Genetic correlation estimates with calving interval and non-return rate were consistently higher for daily BCS than single measure BCS evaluations, but results were not always statistically different. Genetic correlations between BCS change and fertility traits were not significantly different from zero. The product of the accuracy of BCS evaluations with their genetic correlation with the UK fertility index, comprising calving interval and non-return rate, was consistently higher for daily than for single BCS evaluations, by 28 to 53%. This product is associated with the conceptual correlated response in fertility from BCS selection and was highest for early (d 10 to 75) evaluations.

Measures to Evaluate the Effects of DBS on Speech Production

Science.gov (United States)

Weismer, Gary; Yunusova, Yana; Bunton, Kate

2011-01-01

The purpose of this paper is to review and evaluate measures of speech production that could be used to document effects of Deep Brain Stimulation (DBS) on speech performance, especially in persons with Parkinson disease (PD). A small set of evaluative criteria for these measures is presented first, followed by consideration of several speech physiology and speech acoustic measures that have been studied frequently and reported on in the literature on normal speech production, and speech production affected by neuromotor disorders (dysarthria). Each measure is reviewed and evaluated against the evaluative criteria. Embedded within this review and evaluation is a presentation of new data relating speech motions to speech intelligibility measures in speakers with PD, amyotrophic lateral sclerosis (ALS), and control speakers (CS). These data are used to support the conclusion that at the present time the slope of second formant transitions (F2 slope), an acoustic measure, is well suited to make inferences to speech motion and to predict speech intelligibility. The use of other measures should not be ruled out, however, and we encourage further development of evaluative criteria for speech measures designed to probe the effects of DBS or any treatment with potential effects on speech production and communication skills. PMID:24932066

THE SEED PRODUCTIVITY OF PLANTS IN CENOPOPULATION TULIPA BIFLORA UNDER THE CONDITIONS OF The Republic of Kalmykia

Directory of Open Access Journals (Sweden)

Aleksandra Sergeevna Ochirova

2017-12-01

Full Text Available Background: Viable seeds in the composition of populations are considered as an indicator of the life strategy of species. Hence, seed productivity can be considered as an important indicator of species adaptation to habitat conditions. The replaceable productivity of bulbous ephemeroids growing in arid conditions has not been studied sufficiently. In connection with the foregoing, our goal was to identify the seed productivity of plants in the tulip cenopopulations of the two-flowered tulip – Tulipa biflora Pall. (Liliaceae, which is recommended for protection in the conditions of Kalmykia. Materials and metods: Three cenopopulations of Tulipa biflora were studied in different plant communities on brown light loamy solonetzic soils. The sample size was no less than 30 plants of Tulipa biflora, their mature fruits were considered in the aspects of the measured features, their potential and actual seed production, as well as the percentage of seminification. The density of generative plants was taken into account at 10 sites of 0.5 square meters, located along the transect. Resalts: Biometric signs of the fetus in plants in Tulipa biflora populations were positively correlated with air temperature during the active vegetation period of the species. The potential and actual seed productivity of plants in the Tulipa biflora cenpopulations in 2017 is more than in 2016, however, the percentage of seminification marked the reverse results: in 2017 it was 4.7–10.4% lower. In this case, the plants of one of the Tulipa biflora cenopopulations, showed the greatest percentage of seminification in both studies: in 2016 – 77.5, in 2017 – 67.1 pieces of seeds per plant. The mature seed bank which is formed during the growing season in the cenopopulations of Tulipa biflora during the years under the study amounted to 782.8–1338.4 seeds per 1.0 sq.m. Conclusion: The idea of a bank of mature seeds was got – 782.8–1338.4 seeds per 1.0 m2, which is

The iMTA Productivity Cost Questionnaire: A Standardized Instrument for Measuring and Valuing Health-Related Productivity Losses.

Science.gov (United States)

Bouwmans, Clazien; Krol, Marieke; Severens, Hans; Koopmanschap, Marc; Brouwer, Werner; Hakkaart-van Roijen, Leona

2015-09-01

Productivity losses often contribute significantly to the total costs in economic evaluations adopting a societal perspective. Currently, no consensus exists on the measurement and valuation of productivity losses. We aimed to develop a standardized instrument for measuring and valuing productivity losses. A group of researchers with extensive experience in measuring and valuing productivity losses designed an instrument suitable for self-completion, building on preknowledge and evidence on validity. The instrument was designed to cover all domains of productivity losses, thus allowing quantification and valuation of all productivity losses. A feasibility study was performed to check the questionnaire's consistency and intelligibility. The iMTA Productivity Cost Questionnaire (iPCQ) includes three modules measuring productivity losses of paid work due to 1) absenteeism and 2) presenteeism and productivity losses related to 3) unpaid work. Questions for measuring absenteeism and presenteeism were derived from existing validated questionnaires. Because validated measures of losses of unpaid work are scarce, the questions of this module were newly developed. To enhance the instrument's feasibility, simple language was used. The feasibility study included 195 respondents (response rate 80%) older than 18 years. Seven percent (n = 13) identified problems while filling in the iPCQ, including problems with the questionnaire's instructions and routing (n = 6) and wording (n = 2). Five respondents experienced difficulties in estimating the time that would be needed for other people to make up for lost unpaid work. Most modules of the iPCQ are based on validated questions derived from previously available instruments. The instrument is understandable for most of the general public. Copyright © 2015 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

A batch assay to measure microbial hydrogen sulfide production from sulfur-containing solid wastes

Energy Technology Data Exchange (ETDEWEB)

Sun, Mei, E-mail: msun8@uncc.edu [Department of Civil, Construction, and Environmental Engineering, North Carolina State University, Campus Box 7908, Raleigh, NC (United States); Sun, Wenjie, E-mail: wsun@smu.edu [Department of Civil, Construction, and Environmental Engineering, North Carolina State University, Campus Box 7908, Raleigh, NC (United States); Department of Civil and Environmental Engineering, Southern Methodist University, PO Box 750340, Dallas, TX (United States); Barlaz, Morton A., E-mail: barlaz@ncsu.edu [Department of Civil, Construction, and Environmental Engineering, North Carolina State University, Campus Box 7908, Raleigh, NC (United States)

2016-05-01

Large volumes of sulfur-containing wastes enter municipal solid waste landfills each year. Under the anaerobic conditions that prevail in landfills, oxidized forms of sulfur, primarily sulfate, are converted to sulfide. Hydrogen sulfide (H{sub 2}S) is corrosive to landfill gas collection and treatment systems, and its presence in landfill gas often necessitates the installation of expensive removal systems. For landfill operators to understand the cost of managing sulfur-containing wastes, an estimate of the H{sub 2}S production potential is needed. The objective of this study was to develop and demonstrate a biochemical sulfide potential (BSP) test to measure the amount of H{sub 2}S produced by different types of sulfur-containing wastes in a relatively fast (30 days) and inexpensive (125 mL serum bottles) batch assay. This study confirmed the toxic effect of H{sub 2}S on both sulfate reduction and methane production in batch systems, and demonstrated that removing accumulated H{sub 2}S by base adsorption was effective for mitigating inhibition. H{sub 2}S production potentials of coal combustion fly ash, flue gas desulfurization residual, municipal solid waste combustion ash, and construction and demolition waste were determined in BSP assays. After 30 days of incubation, most of the sulfate in the wastes was converted to gaseous or aqueous phase sulfide, with BSPs ranging from 0.8 to 58.8 mL H{sub 2}S/g waste, depending on the chemical composition of the samples. Selected samples contained solid phase sulfide which contributed to the measured H{sub 2}S yield. A 60 day incubation in selected samples resulted in 39–86% additional sulfide production. H{sub 2}S production measured in BSP assays was compared with that measured in simulated landfill reactors and that calculated from chemical analyses. H{sub 2}S production in BSP assays and in reactors was lower than the stoichiometric values calculated from chemical composition for all wastes tested, demonstrating

Uncertainty of slip measurements in a cutting system of converting machinery for diapers production

Directory of Open Access Journals (Sweden)

D’Aponte F.

2015-01-01

Full Text Available In this paper slip measurements are described between the peripheral surfaces of knife and a not driven anvil cylinders in a high velocity, high quality cutting unit of a diaper production line. Laboratory tests have been carried out on a test bench with real scale components for possible on line application of the method. With reference to both starting and steady state conditions correlations with the process parameters have been found, achieving a very satisfactory reduction of the slip between the knife cylinder and the not driven anvil one. Accuracy evaluation of measurements allowed us to validate the obtained information and to evaluate the detection threshold of the measurement method in the present configuration The analysis of specific uncertainty contributions to the whole uncertainty could be also used, to further reduce the requested uncertainty of the measurement method.

Di-boson production measurements with the ATLAS detector

CERN Document Server

Chevalier, Laurent; The ATLAS collaboration

2015-01-01

Measurements diboson production cross sections in proton-proton interactions at 7 and 8 TeV are reported from the ATLAS experiment. The cross section results are measured in phase space regions defined by the decay kinematics and then extrapolated to the full phase spaces. Cross sections for WV (V=W or Z) production in the leptonic or semileptonic channels are compared to (N)NLO predictions of the Standard Model and are used to place constraints on anomalous triple-gauge-boson couplings. First LHC Run-2 results will be included if available.

Instrumentation for localized measurements in two-phase flow conditions

International Nuclear Information System (INIS)

Neff, G.G.; Averill, R.H.; Shurts, S.W.

1979-01-01

Three types of instrumentation that have been developed by EG and G Idaho, Inc., and its predecessor, Aerojet Nuclear company, at the Idaho National Engineering Laboratory to investigate two-phase flow phenomenon in a nuclear reactor at the Loss-of-Fluid Test (LOFT) facility are discussed: (a) a combination drag disc-turbine transducer (DTT), (b) a multibeam nuclear hardened gamma densitometer system, and (c) a conductivity sensitive liquid level transducer (LLT). The DTT obtains data on the complex problem of two-phase flow conditions in the LOFT primary coolant system during a loss-os-coolant experiment (LOCE). The discussion of the DTT describes how a turbine, measuring coolant velocity, and a drag disc, measuring coolant momentum flux, can provide valuable mass flow data. The nuclear hardened gamma densitometer is used to obtain density and flow regime information for two-phase flow in the LOFT primary coolant system during a LOCE. The LLT is used to measure water and steam conditions within the LOFT reactor core during a LOCE. The LLT design and the type of data obtained are described

Heating, Ventilation, and Air Conditioning Design Strategy for a Hot-Humid Production Builder

Energy Technology Data Exchange (ETDEWEB)

Kerrigan, P. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-03-01

BSC worked directly with the David Weekley Homes - Houston division to redesign three floor plans in order to locate the HVAC system in conditioned space. The purpose of this project is to develop a cost effective design for moving the HVAC system into conditioned space. In addition, BSC conducted energy analysis to calculate the most economical strategy for increasing the energy performance of future production houses. This is in preparation for the upcoming code changes in 2015. The builder wishes to develop an upgrade package that will allow for a seamless transition to the new code mandate. The following research questions were addressed by this research project: 1. What is the most cost effective, best performing and most easily replicable method of locating ducts inside conditioned space for a hot-humid production home builder that constructs one and two story single family detached residences? 2. What is a cost effective and practical method of achieving 50% source energy savings vs. the 2006 International Energy Conservation Code for a hot-humid production builder? 3. How accurate are the pre-construction whole house cost estimates compared to confirmed post construction actual cost? BSC and the builder developed a duct design strategy that employs a system of dropped ceilings and attic coffers for moving the ductwork from the vented attic to conditioned space. The furnace has been moved to either a mechanical closet in the conditioned living space or a coffered space in the attic.

Optimization on Pretreatment Conditions of Seaweed Liquid Waste for Bio ethanol Production

International Nuclear Information System (INIS)

Nur Zatul-Iffah Zakaria; Dachyar Arbain; Mohd Noor Ahmad; Mohd Irfan Hatim Mohamed Dzahir

2015-01-01

Seaweed liquid waste (SLW) from a non-conventional seaweed (Gracilaria sp.) drying process where the seaweed is ruptured and filter-squeezed has been investigated. The liquid contains proteins and minerals which potentially pollute the environment if it is not been properly treated. For that reason, this paper deals with study on the feasibility of SLW utilization as a feedstock for bio ethanol production. The fermentation of bio ethanol production was carried out by Saccharomyces cerevisiae in which ethanol produced was measured by gas chromatography. In order to increase its fermentable sugar content, the SLW was treated with dilute acid. Center composite design of response surface methodology (RSM) had been used to optimize the sugar content by varying the parameters involved in the dilute acid pretreatment conditions. These are sulphuric acid concentration (M), temperature (degree Celsius) and seaweed waste concentration (g/ ml). It was obtained that the R 2 value reached 0.97 indicating that the model is acceptable. The three parameters showed p-value less than 0.05 suggesting their significance interactions. The optimization resulted 25 times improvement of reducing sugar concentration. The reducing sugar resulting from the optimized pretreatment was later used as fermentation medium to produce ethanol up to 123.197 mg/ l. (author)

Measuring the coolness of interactive products

DEFF Research Database (Denmark)

Bruun, Anders; Raptis, Dimitrios; Kjeldskov, Jesper

2016-01-01

Coolness has recently started to be explored as a design goal for interactive products from practitioners as well as researchers within human–computer interaction (HCI), but there is still a need to further operationalise the concept and explore how we can measure it. Our contribution in this paper...

Radiation measurements during cavities conditioning on APS RF test stand

International Nuclear Information System (INIS)

Grudzien, D.M.; Kustom, R.L.; Moe, H.J.; Song, J.J.

1993-01-01

In order to determine the shielding structure around the Advanced Photon Source (APS) synchrotron and storage ring RF stations, the X-ray radiation has been measured in the near field and far field regions of the RF cavities during the normal conditioning process. Two cavity types, a prototype 352-MHz single-cell cavity and a 352-MHz five-cell cavity, are used on the APS and are conditioned in the RF test stand. Vacuum measurements are also taken on a prototype 352-MHz single-cell cavity and a 352-MHz five-cell cavity. The data will be compared with data on the five-cell cavities from CERN

Implications of energy efficiency measures in wheat production

DEFF Research Database (Denmark)

Meyer-Aurich, Andreas; Ziegler, T.; Scholz, L.

The economic and environmental effect of energy saving measures were analyzed for a typical wheat production system in Germany. The introduction of precision farming, reduced nitrogen fertilization and improved crop drying technologies proved to be efficient measures for enhancing energy efficiency...

Analytical measurements of fission products during a severe nuclear accident

Science.gov (United States)

Doizi, D.; Reymond la Ruinaz, S.; Haykal, I.; Manceron, L.; Perrin, A.; Boudon, V.; Vander Auwera, J.; tchana, F. Kwabia; Faye, M.

2018-01-01

The Fukushima accident emphasized the fact that ways to monitor in real time the evolution of a nuclear reactor during a severe accident remain to be developed. No fission products were monitored during twelve days; only dose rates were measured, which is not sufficient to carry out an online diagnosis of the event. The first measurements were announced with little reliability for low volatile fission products. In order to improve the safety of nuclear plants and minimize the industrial, ecological and health consequences of a severe accident, it is necessary to develop new reliable measurement systems, operating at the earliest and closest to the emission source of fission products. Through the French program ANR « Projet d'Investissement d'Avenir », the aim of the DECA-PF project (diagnosis of core degradation from fission products measurements) is to monitor in real time the release of the major fission products (krypton, xenon, gaseous forms of iodine and ruthenium) outside the nuclear reactor containment. These products are released at different times during a nuclear accident and at different states of the nuclear core degradation. Thus, monitoring these fission products gives information on the situation inside the containment and helps to apply the Severe Accident Management procedures. Analytical techniques have been proposed and evaluated. The results are discussed here.

Analytical measurements of fission products during a severe nuclear accident

Directory of Open Access Journals (Sweden)

Doizi D.

2018-01-01

Full Text Available The Fukushima accident emphasized the fact that ways to monitor in real time the evolution of a nuclear reactor during a severe accident remain to be developed. No fission products were monitored during twelve days; only dose rates were measured, which is not sufficient to carry out an online diagnosis of the event. The first measurements were announced with little reliability for low volatile fission products. In order to improve the safety of nuclear plants and minimize the industrial, ecological and health consequences of a severe accident, it is necessary to develop new reliable measurement systems, operating at the earliest and closest to the emission source of fission products. Through the French program ANR « Projet d’Investissement d’Avenir », the aim of the DECA-PF project (diagnosis of core degradation from fission products measurements is to monitor in real time the release of the major fission products (krypton, xenon, gaseous forms of iodine and ruthenium outside the nuclear reactor containment. These products are released at different times during a nuclear accident and at different states of the nuclear core degradation. Thus, monitoring these fission products gives information on the situation inside the containment and helps to apply the Severe Accident Management procedures. Analytical techniques have been proposed and evaluated. The results are discussed here.

Productivity benefits of industrial energy efficiency measures

Energy Technology Data Exchange (ETDEWEB)

Worrell, Ernst; Laitner, John A.; Michael, Ruth; Finman, Hodayah

2004-08-30

We review the relationship between energy efficiency improvement measures and productivity in industry. We review over 70 industrial case studies from widely available published databases, followed by an analysis of the representation of productivity benefits in energy modeling. We propose a method to include productivity benefits in the economic assessment of the potential for energy efficiency improvement. The case-study review suggests that energy efficiency investments can provide a significant boost to overall productivity within industry. If this relationship holds, the description of energy-efficient technologies as opportunities for larger productivity improvements has significant implications for conventional economic assessments. The paper explores the implications this change in perspective on the evaluation of energy-efficient technologies for a study of the iron and steel industry in the US. This examination shows that including productivity benefits explicitly in the modeling parameters would double the cost-effective potential for energy efficiency improvement, compared to an analysis excluding those benefits. We provide suggestions for future research in this important area.

Investigation of oil production conditions and production operation by solution gas drive in low permeable heterogeneous limestones

Energy Technology Data Exchange (ETDEWEB)

Lillie, W

1966-04-01

It was the purpose of this study to investigate the production of oil and gas from a low permeable heterogeneous limestone-reservoir by solution gas drive. The rock-samples were subjected to extensive petrolphysical analyses in order to characterize the pore structure of of the limestone material. Laboratory model flow tests were undertaken to outline in detail the production history during the pressure depletion process under reservoir conditions and by using original reservoir fluids. The experiments were carried out at different rates of pressure decline. It can be stated that the rate of pressure decline is the most important factor affecting the oil recovery and the development of the gas-oil-ratio in a model flow test. The present investigation leads to the following conclusion: It is posible to get reliable results which could be the base for a reservoir performance prediction only when the gas and oil phase are maintained at equilibrium conditions within the rock sample during the pressure decline. An additional calculation of the solution gas drive reservoir production history by the Tarner method shows a good agreement of the experimental and the calculated data. (40 refs.)

Sewage sludge hydrochars: properties and agronomic impact as related to different production conditions

Science.gov (United States)

Paneque, Marina; María De la Rosa, José; Aragón, Carlos; Kern, Jürgen; Conte, Pellegrino; Knicker, Heike

2015-04-01

amount of hydrochar equivalent to 5 and 25 t ha-1 were prepared in quadruplicate for each hydrochar using Lolium perenne as test plant (25 seeds per pot). Hydrochars were not washed before this experiment. Control pots, without hydrochar amendment, were also settled for comparison purposes (n=6). After adjusting the soil humidity to 60% of the maximum WHC, the pots were placed into a greenhouse under similar conditions than those reported by [3]. In this experiment germination, survival rates and biomass production per pot were measured periodically. Elemental analysis and the determination of several chemical properties of hydrochars such as pH, electrical conductivity and ash content were performed. Additionally, 13C solid-state nuclear magnetic resonance (NMR) was applied to elucidate the main chemical groups whereas fast field cycling (FFC) NMR relaxometry was valuable for investigating the porous structure and water dynamic in the different hydrochars. This work confirmed that production conditions of hydrochars vary their chemical properties and hence their agronomic effect. Biomass production raised significantly in presence of all hydrochars, being the response in presence of hydrochars produced at 200˚C significantly higher than the response in presence of hydrochars produced at 260˚C, whereas the residence time of the hydrochars in the reactor did not affect biomass productivity. Concerning the characterization data, hydrochars which showed the highest biomass production were those which contain the highest mineralized nitrogen content (NH4, NO2 and NO3) and a greater presence of alkyl carbons and carboxyl groups. Hydrochars FFC NMR relaxometry results show a lower T1 (longitudinal relaxation time) compared to the pure sewage sludge, which suggests that HTC processes reduced the average pore size of the system. This has further implications in the water and nutrient retention capacity of the hydrochars compared to the pure sewage sludge. Acknowledgements: The

Biological compost stability influences odor molecules production measured by electronic nose during food-waste high-rate composting

International Nuclear Information System (INIS)

D'Imporzano, Giuliana; Crivelli, Fernando; Adani, Fabrizio

2008-01-01

Composting is a technique that is used to convert organic waste into agriculturally useful products. Composting is an aerobic, solid-state biological process, which typically can be divided into two phases, a high-rate composting phase and a curing phase. High-rate composting plays an important role during the composting process, owing to the high microbial activity occurring during this phase. It requires an accurate plant design to prevent the formation of anaerobic conditions and odors. The formation of anaerobic conditions mainly depends on the rate of O 2 consumption needed to degrade the substrate, i.e., the biological stability of the substrate. In this study, we investigated the relationship between the biological activity, measured by the dynamic respiration index (DRI) and the odor molecules production, measured by an electronic nose (EN) during two food-waste high-rate composting processes. Although the O 2 concentration in the biomass free air space (FAS) was kept optimal (O 2 > 140 ml l -1 , v/v) during composting, strong anaerobic conditions developed. This was indicated by the high levels of sulfur compounds, methane, and hydrogen in the outlet air stream. Both the high level of O 2 consumption, needed to degrade the high-degradable water-soluble organic matter and the low water O 2 solubility, caused by high temperature reached in this stage (up to 60 deg. C), led to the anaerobic conditions observed in the biofilm-particle level. The application of the partial least square (PLS) analysis demonstrated a good regression between the DRI and the odor molecules produced that was detected by the EN (R 2 = 0.991; R 2 CV = 0.990), signifying the usefulness of the DRI as a parameter to estimate the potential production of odor molecules of the biomass

Evaluation of water quality conditions near proposed fish production sites associated with the Yakima Fisheries Project. Final report

International Nuclear Information System (INIS)

Dauble, D.d.; Mueller, R.P.; Martinson, G.A.

1994-05-01

In 1991, the Pacific Northwest Laboratory (PNL) began studying water quality at several sites in the Yakima River Basin for the Bonneville Power Administration. These sites were being proposed as locations for fish culture facilities as part of the Yakima Fisheries Project (YFP). Surface water quality parameters near the proposed fish culture facilities are currently suitable for fish production. Water quality conditions in the mainstream Yakima River and its tributaries are generally excellent in the upper part of the watershed (i.e., near Cle Elum), but they are only fair to poor for the river downstream of Union Gap (river mile 107). Water quality of the Naches River near Oak Flats is also suitable for fish production. Groundwater supplies near the proposed fish production facilities typically have elevated concentrations of metals and dissolved gases. These conditions can be mitigated using best engineering practices such as precipitation and degasification. Additionally, mixing with surface water may improve these conditions. Depending on the location and depth of the well, groundwater temperatures may be warmer than optimum for acclimating and holding juvenile and adult fish. Water quality parameters measured in the Yakima River and tributaries sometimes exceed the range of values described as acceptable for culture of salmonids and for the protection of other aquatic life. However, constituent concentrations are within ranges that exist in many northwest fish hatcheries. Additionally, site-specific tests conducted by PNL (i.e., live box exposures and egg incubation studies) indicate that fish can be successfully reared in surface and well water near the proposed facility sites. Thus, there appear to be no constraints to artificial production for the YFP

Genotypic interactions with potassium nutrition on fruit production in cotton (gossypium hirsutum l.) under irrigated conditions

International Nuclear Information System (INIS)

Makhdum, M.I.; Pervez, H.; Ashraf, M.

2005-01-01

A field experiment was conducted using four (Gossypium hirsutum l.) cultivars (OM-448, OM-I00, NIAB-Karishma, 5-12) at four rates of potassium (0, 62, 5, 125, 250 kg K ha-1) and with two sources of potassium (K/sub 2/S0/sub 4/, KCI) to determine the effects of potassium (K) fertilizer on fruit production under irrigated conditions. Cultivars differed significantly amongst themselves in production and retention of fruits per unit land area. The cultivars were categorized as OM-448>OM-1100>Karishma>5-12 in order of fruit production. The number of total fruiting positions increased with concurrent levels of K-fertilizer. The shedding of fruit was significantly reduced by application of 250 kg K ha-1 compared to zero K-rate treatment. The addition of K-fertilizer in the form of K/sub 2/S0/sub 4/ showed an edge over KCI in fruit production. A high degree of correlation (r 0.89**,0.91**, -0.8**) was measured between seed cotton yield and number of total fruiting positions, number of intact fruit and fruit shedding percentage respectively. (author)

Enhancing Ethanol Production by Fermentation Using Saccharomyces cereviseae under Vacuum Condition in Batch Operation

Directory of Open Access Journals (Sweden)

A Abdullah

2012-02-01

Full Text Available Ethanol is one of renewable energy, which considered being an excellent alternative clean-burning fuel to replaced gasoline. In fact, the application of ethanol as fuel still blended with gasoline. The advantages of using ethanol as fuel are that the raw material mostly from renewable resources and the product has low emission which means environmental friendly. Ethanol can be produced by fermentation of sugars (glucose/fructose. The constraint in the ethanol fermentation batch or continuous process is the ethanol product inhibition. Inhibition in ethanol productivity and cell growth can be overcome by taking the product continuously from the fermentor. The process can be done by using a vacuum fermentation. The objective of this research is to investigate the effect of pressure and glucose concentration in ethanol fermentation. The research was conducted in laboratory scale and batch process. Equipment consists of fermentor with vacuum system. The observed responses were dried cells of yeast, concentration of glucose, and concentration of ethanol. Observations were made every 4 hours during a day of experiment. The results show that the formation of ethanol has a growth-associated product characteristic under vacuum operation. Vacuum condition can increase the cell formation productivity and the ethanol formation, as it is compared with fermentation under atmospheric condition. The maximum cells productivity and ethanol formation in batch operation under vacuum condition was reached at 166.6 mmHg of pressure. The maximum numbers of cells and ethanol formation was reached at 141.2 mm Hg of pressure. High initial glucose concentration significantly can affect the productivity and the yield of ethanol.

Nitrous Oxide Production and Fluxes from Coastal Sediments under Varying Environmental Conditions

Science.gov (United States)

Ziebis, W.; Wankel, S. D.; de Beer, D.; Dentinger, J.; Buchwald, C.; Charoenpong, C.

2014-12-01

Although coastal zones represent important contributors to the increasing levels of atmospheric nitrous oxide (N2O), it is still unclear which role benthic processes play and whether marine sediments represent sinks or sources for N2O, since interactions among closely associated microbial groups lead to a high degree of variability. In addition, coastal areas are extremely dynamic regions, often exposed to increased nutrient loading and conditions of depleted oxygen. We investigated benthic N2O fluxes and how environmental conditions affect N2O production in different sediments at 2 different geographical locations (German Wadden Sea, a California coastal lagoon). At each location, a total of 32 sediment cores were taken in areas that differed in sediment type, organic content and pore-water nutrient concentrations, as well as in bioturbation activity. Parallel cores were incubated under in-situ conditions, low oxygen and increased nitrate levels for 10 days. Zones of N2O production and consumption were identified in intact cores by N2O microprofiles at the beginning and end of the experiments. In a collaborative effort to determine the dominant sources of N2O, samples were taken throughout the course of the experiments for the determination of the isotopic composition of N2O (as well as nitrate, nitrite and ammonium). Our results indicate that both, nitrate addition and low oxygen conditions in the overlying water, caused an increase of subsurface N2O production in most sediments, with a high variability between different sediment types. N2O production in the sediments was accompanied by N2O consumption, reducing the fluxes to the water column. In general, organic rich sediments showed the strongest response to environmental changes with increased production and efflux of N2O into the overlying water. Bioturbation activity added to the complexity of N2O dynamics by an increase in nitrification-denitrification processes, as well as enhanced pore-water transport

Measurement of Single-top Quark Production with the ATLAS Detector

CERN Document Server

Holzbauer, J L

2011-01-01

Single-top production has been studied with the ATLAS detector using 0.7 fb-1 of 2011 data recorded at 7 TeV center-of-mass energy. The measurement of electroweak production of top-quarks allows probes of the Wtb vertex and a direct measurement of the CKM matrix element |V_tb|. It is also expected to be sensitive to new physics such as flavor changing neutral currents or heavy W production. The t-channel cross-section measurements are performed using both a cut-based and neural network approach, while a cut-based selection in the dilepton channel is used to derive a limit on the associated (Wt) production. An observed cross-section of 90 +32 -22 pb (65 +28 -19 pb expected) is obtained for the t-channel, which is consistent with the Standard Model expectation. For the Wt production, an observed limit of < 39.1 pb (40.6 pb expected) is derived, which corresponds to about 2.5 times the Standard Model expectation.

Measuring method to impulse neutron scattering background in complicated ambient condition

International Nuclear Information System (INIS)

Tang Zhangkui; Peng Taiping; Tang Zhengyuan; Liu Hangang; Hu Mengchun; Fan Juan

2004-01-01

This paper introduced a measuring method and calculative formula about impulse neutron scattering background in complicated ambient condition. The experiment had been done in the lab, and the factors to affect measurement conclusion were analysised. (authors)

Comparison of the corrosion potential for stainless steel measured in-plant and in laboratory during BWR normal water chemistry conditions

International Nuclear Information System (INIS)

Molander, A.; Pein, K.; Tarkpea, P.; Takagi, Junichi; Karlberg, G.; Gott, K.

1998-01-01

To obtain reliable crack growth rate date for stainless steel in BWR environments careful laboratory simulation of the environmental conditions is necessary. In the plant the BWR normal water chemistry environment contains hydrogen peroxide, oxygen and hydrogen. However, in crack growth rate experiments in laboratories, the environment is normally simulated by adding 200 ppb oxygen to the high temperature water. Thus, as hydrogen peroxide is a more powerful oxidant than oxygen, it is to be expected that a lower corrosion potential will be measured in the laboratory than in the plant. To resolve this issue this work has been performed. In-plant and laboratory measurements have often been performed with somewhat different equipment, due to the special requirements concerning in-plant measurements. In this work such differences have been avoided and two identical sets of equipment for electrochemical measurements were built and used for measurements in-plant in a Swedish BWR and in high purity water in the laboratory. The host plant was Barsebaeck 1. Corrosion potential monitoring in-plant was performed under both NWC (Normal Water Chemistry) and HWC (Hydrogen Water Chemistry) conditions. This paper is, however, focused on NWC conditions. This is due to the fact, that the total crack growth obtained during a reactor cycle, can be determined by NWC conditions, even for plants running with HWC due to periodic stops in the hydrogen addition for turbine inspections or failure of the dosage or hydrogen production equipment. Thus, crack growth data for NWC is of great importance both for BWRs operating with HWC and NWC. Measurements in-plant and in the laboratory were performed during additions of oxygen and hydrogen peroxide to the autoclave systems. The corrosion potentials were compared for various conditions in the autoclaves, as well as versus in-plant in-pipe corrosion potentials. (J.P.N.)

Thickness measuring instrument for rubber cord calender production

International Nuclear Information System (INIS)

Ye Songfeng

1988-01-01

The thickness measuring gauge has been used to measure the rubber film thickness on the coating of textile cord at tire four cord calenders. Combined with micro-computer it completes the automatic control system and acheives automatic thickness measurement and adjustment. The fundamentals, construction, specifications, characteristic and application results are described. Prominent economic benefit has been gained for tire production

Electrical condition monitoring method for polymers

Science.gov (United States)

Watkins, Jr. Kenneth S.; Morris, Shelby J.; Masakowski, Daniel D.; Wong, Ching Ping; Luo, Shijian

2010-02-16

An electrical condition monitoring method utilizes measurement of electrical resistivity of a conductive composite degradation sensor to monitor environmentally induced degradation of a polymeric product such as insulated wire and cable. The degradation sensor comprises a polymeric matrix and conductive filler. The polymeric matrix may be a polymer used in the product, or it may be a polymer with degradation properties similar to that of a polymer used in the product. The method comprises a means for communicating the resistivity to a measuring instrument and a means to correlate resistivity of the degradation sensor with environmentally induced degradation of the product.

Diet and bioclimatic conditions on production and milk quality

Directory of Open Access Journals (Sweden)

F. P. Campos

2018-05-01

Full Text Available It was aimed to analyze the productive performance of lactating cows on isoprotein fed diets, at differentiated environmental conditions. Eight Holstein cows were used, grouped in two 4 × 4 balanced Latin squares design. The treatments were evaluated in 2 × 2 factorial designs: sources of roughage (corn silage – CS plus concentrate, and the combination of corn silage with sugarcane - CSSC, 1:1 on DM, plus concentrate and distinct environment (with= WS and without= OS, fan and nebulizers system= Sfn. The estimation of dry matter intake (DMI, productive performance and physicochemical parameters of milk were evaluated. There was no interaction effect of environment factors and source of forage. There was signiÀ cant effects for the source forage factors, where the DMI for the CSSC based diet was higher than the CS based diet in the effect of forage (4.22 vs. 4.06% BW, and 22.3 vs. 21.7 kg/d, respectively, P≤0.05, but with similar milk production correcting 3.5% fat (23.01 vs. 22.62, CSSC and CS; 22.85 vs. 22.78 kg/day, WS and OS, respectively, P≥0.05. The feed efÀ ciency and conversion was similar in both factors (102.8 vs. 104.7% and 0.99 vs. 1.0, CSSC and CS; 102.5 vs. 104.9% and 1.0 vs. 0.99, WS and OS, respectively, P≥0.05. The beneÀ t-diet cost ratio was higher for CS-based diet than for CSSC (7.44 vs. 6.97, P≤0.05. There were effects only in the forage factor for CP milk (3.26 vs. 3.23%, P≤0.05, lactose (4.54 vs. 4.49%, P≤0.05 and urea nitrogen in milk (23.21 vs. 20.71 mg/dL, P≤0.05 and the superiority arising from the CSSC-based diet in comparison to the CS diet. There was higher for T and THI (28.1 vs. 23.6°C and 75.1 vs. 71.1, respectively, P≤0.05, and lower RH to 2:00 pm (47.7 vs. 64.5%, P≤0.05. The linear score showed negative correlations with DMI, milk production, lactose and urea nitrogen (-0.36, -0.69, -0.44 and -0.32, P≤0.05, respectively. The use of the diet based on CSSC proposed increases in DMI and

Microcalorimetric measurements of heat production in human erythrocytes. IV. Comparison between different calorimetric techniques, suspension media, and preparation methods.

Science.gov (United States)

Monti, M; Wadsö, I

1976-10-01

Heat production in human erythrocytes from healthy subjects has been measured under different experimental conditions. Simultaneous measurements were made on the same samples using different types of microcalorimeters: a static ampoule calorimeter, an air perfusion calorimeter, and a flow calorimeter. Obtained heat effect values for specified standard conditions, P degrees, were within uncertainty limits the same for the different calorimeters. Cells were suspended either in autologous plasma or in a phosphate buffer. P degrees values for buffer suspensions were significantly higher than those for plasma suspensions. Erythrocyte samples prepared by the column adsorption technique gave higher P degrees values than those obtained by a conventional centrifugation procedure.

The Role of Condition-Specific Preference-Based Measures in Health Technology Assessment.

Science.gov (United States)

Rowen, Donna; Brazier, John; Ara, Roberta; Azzabi Zouraq, Ismail

2017-12-01

A condition-specific preference-based measure (CSPBM) is a measure of health-related quality of life (HRQOL) that is specific to a certain condition or disease and that can be used to obtain the quality adjustment weight of the quality-adjusted life-year (QALY) for use in economic models. This article provides an overview of the role and the development of CSPBMs, and presents a description of existing CSPBMs in the literature. The article also provides an overview of the psychometric properties of CSPBMs in comparison with generic preference-based measures (generic PBMs), and considers the advantages and disadvantages of CSPBMs in comparison with generic PBMs. CSPBMs typically include dimensions that are important for that condition but may not be important across all patient groups. There are a large number of CSPBMs across a wide range of conditions, and these vary from covering a wide range of dimensions to more symptomatic or uni-dimensional measures. Psychometric evidence is limited but suggests that CSPBMs offer an advantage in more accurate measurement of milder health states. The mean change and standard deviation can differ for CSPBMs and generic PBMs, and this may impact on incremental cost-effectiveness ratios. CSPBMs have a useful role in HTA where a generic PBM is not appropriate, sensitive or responsive. However, due to issues of comparability across different patient groups and interventions, their usage in health technology assessment is often limited to conditions where it is inappropriate to use a generic PBM or sensitivity analyses.

Photochemical processes and ozone production in Finnish conditions

Energy Technology Data Exchange (ETDEWEB)

Laurila, T; Hakola, H [Finnish Meteorological Inst., Helsinki (Finland). Air Quality Dept.

1997-12-31

Photochemical ozone production is observed in March-September. Highest ozone concentrations and production efficiencies are observed in spring in the northern parts and in summer in the southern parts of the country. VOC concentrations are relatively low compared to continental areas in general. During the growing season a substantial part of the total reactive mass of VOCs is of biogenic origin. Large forest areas absorb ozone substantially, decreasing the ambient ozone concentrations in central and northern parts of Finland where long-range transport of ozone is relatively important compared to local production. The aim of the work conducted at Finnish Meteorological Institute has been to characterise concentrations of photochemically active species in the boundary layer and their photochemical formation and deposition including the effects on vegetation. Also interactions between the boundary layer and free troposphere of ozone have been studied. In the future, fluxes of both biogenic species and air pollutants will be measured and the models will be further developed so that the photochemical and micrometeorological processes could be better understood

Photochemical processes and ozone production in Finnish conditions

Energy Technology Data Exchange (ETDEWEB)

Laurila, T.; Hakola, H. [Finnish Meteorological Inst., Helsinki (Finland). Air Quality Dept.

1996-12-31

Photochemical ozone production is observed in March-September. Highest ozone concentrations and production efficiencies are observed in spring in the northern parts and in summer in the southern parts of the country. VOC concentrations are relatively low compared to continental areas in general. During the growing season a substantial part of the total reactive mass of VOCs is of biogenic origin. Large forest areas absorb ozone substantially, decreasing the ambient ozone concentrations in central and northern parts of Finland where long-range transport of ozone is relatively important compared to local production. The aim of the work conducted at Finnish Meteorological Institute has been to characterise concentrations of photochemically active species in the boundary layer and their photochemical formation and deposition including the effects on vegetation. Also interactions between the boundary layer and free troposphere of ozone have been studied. In the future, fluxes of both biogenic species and air pollutants will be measured and the models will be further developed so that the photochemical and micrometeorological processes could be better understood

Measurement of broiler litter production rates and nutrient content using recycled litter.

Science.gov (United States)

Coufal, C D; Chavez, C; Niemeyer, P R; Carey, J B

2006-03-01

It is important for broiler producers to know litter production rates and litter nutrient content when developing nutrient management plans. Estimation of broiler litter production varies widely in the literature due to factors such as geographical region, type of housing, size of broiler produced, and number of flocks reared on the same litter. Published data for N, P, and K content are also highly variable. In addition, few data are available regarding the rate of production, characteristics, and nutrient content of caked litter (cake). In this study, 18 consecutive flocks of broilers were reared on the same litter in experimental pens under simulated commercial conditions. The mass of litter and cake produced was measured after each flock. Samples of all litter materials were analyzed for pH, moisture, N, P, and K. Average litter and cake moisture content were 26.4 and 46.9%, respectively. Significant variation in litter and cake nutrient content was observed and can largely be attributed to ambient temperature differences. Average litter, cake, and total litter (litter plus cake) production rates were 153.3, 74.8, and 228.2 g of dry litter material per kg of live broiler weight (g/kg) per flock, respectively. Significant variation in litter production rates among flocks was also observed. Cumulative litter, cake, and total litter production rates after 18 flocks were 170.3, 78.7, and 249.0 g/kg, respectively. The data produced from this research can be used by broiler producers to estimate broiler litter and cake production and the nutrient content of these materials.

Impacts of environmental conditions on product formation and morphology of Yarrowia lipolytica.

Science.gov (United States)

Timoumi, Asma; Guillouet, Stéphane E; Molina-Jouve, Carole; Fillaudeau, Luc; Gorret, Nathalie

2018-05-01

The yeast Yarrowia lipolytica is an industrially important microorganism with distinctive physiological and metabolic characteristics. A variety of external factors (e.g., pH, temperature, and nutrient availability) influences the behavior of the yeast and may act as stress conditions which the cells must withstand and adapt. In this mini review, the impacts of environmental factors on the morphology and metabolite production by Y. lipolytica are summarized. In this regard, detailed insights into the effectors involved in the dimorphic transition of Y. lipolytica, the cultivation conditions employed, as well as the methods applied for the morphological characterization are highlighted. Concerning the metabolism products, a special focus is addressed on lipid and citric acid metabolites which have attracted significant attention in recent years. The dependence of lipid and citric acid productivity on key process parameters, such as media composition and physico-chemical variables, is thoroughly discussed. This review attempts to provide a recent update on the topic and will serve as a meaningful resource for researchers working in the field.

Optimization of culture condition for ACEI and GABA production by lactic acid bacteria.

Science.gov (United States)

Tung, Yi-Ting; Lee, Bao-Hong; Liu, Chin-Feng; Pan, Tzu-Ming

2011-01-01

Gamma-aminobutyric acid (GABA) and angiotensin-converting enzyme inhibitor (ACEI) are compounds which can influence hypertension. The goal of this study is to optimize the culture condition for GABA and ACEI production by Lactobacillus plantarum NTU 102 fermented skim milk. In this study, we used 3-factor-3-level Box-Behnken design combining with response surface methodology, where the 3 factors represent the concentration of skim milk, the concentration of monosodium glutamate, and culture temperature. Best conditions for GABA and ACEI production differed. The results indicated that L. plantarum NTU 102 produced the highest combined levels of GABA and ACEI at 37 °C, in milk having 8% to 12% nonfat solids supplemented with 0.6% to 1% MSG. Agitation of the medium during fermentation had no effect on GABA or ACEI production but extended incubation (up to 6 d) increases levels of the bioactive compounds. L. plantarum NTU 102 fermented products may be a potential functional food source for regulating hypertension. © 2011 Institute of Food Technologists®

Reconstruction of photon number conditioned states using phase randomized homodyne measurements

International Nuclear Information System (INIS)

Chrzanowski, H M; Assad, S M; Bernu, J; Hage, B; Lam, P K; Symul, T; Lund, A P; Ralph, T C

2013-01-01

We experimentally demonstrate the reconstruction of a photon number conditioned state without using a photon number discriminating detector. By using only phase randomized homodyne measurements, we reconstruct up to the three photon subtracted squeezed vacuum state. The reconstructed Wigner functions of these states show regions of pronounced negativity, signifying the non-classical nature of the reconstructed states. The techniques presented allow for complete characterization of the role of a conditional measurement on an ensemble of states, and might prove useful in systems where photon counting still proves technically challenging. (paper)

Measurement of the perceived quality of a product

Directory of Open Access Journals (Sweden)

Maire J.-L.

2013-01-01

Full Text Available For some companies, visual inspection has become an essential step when seeking to improve the quality of their products. The aim of this control is to be sure of the perceived quality of the product, which often goes well beyond the quality expected by the customer. For this type of control, the controller should be able to detect any anomaly on a product, characterize this anomaly, and then evaluate it in order to decide if the product should be accepted or rejected. This paper describes how this characterization can be carried out and, more specifically, how to measure the impact of the local environment of an anomaly on the perceived quality of the product.

ALICE measurements of heavy-flavour production at the LHC

CERN Multimedia

CERN. Geneva

2012-01-01

The measurement of open charm and beauty production in Pb-Pb collisions at the LHC gives access to the mechanisms of heavy-quark transport and energy loss in hot and dense QCD matter. The ALICE apparatus allows us to measure heavy flavour particles over a wide acceptance, using hadronic and electronic final states at central rapidity and muonic final states at forward rapidity, in both cases with coverage down to low transverse momentum. These measurements, in pp collisions, besides constituting the reference for the heavy-ion studies, provide acceptance-wise unique information on heavy-quark production at LHC energies. After presenting results for pp collisions at centre-of-mass energies of 2.76 and 7 TeV, we focus on the observation of the suppression of heavy-flavour production in central Pb-Pb collisions and of the azimuthal anisotropy of charmed hadrons in semi-central collisions at 2.76 TeV.

Measurement of Scientific Productivity in R&D Sector: Changing paradigm.

Science.gov (United States)

Kumar, Abhishek; Srivastava, Alpana; Kumar, R P Jeevan; Tiwari, Rajesh K

2017-01-01

Scientific Productivity is a demand of policy makers for a judicious utilization of massive R&D budget allocated and utilized. A huge mass of intellectual assets is employed, which after investing manpower, infrastructure and lab consumables demand for a major outcome which contributes towards building nation's economy. Scientific productivity was only measured through publications or patents. Patents, earmarked as a strong parameter for innovation generation, where, Word Intellectual Property Organisation generated a data on applications for the top 20 offices for patents, where Australia, Brazil and Canada occupied top 3 positions. India ranked 9th with the total patent applications rising from 39762 (2010) to 42854 (2014) i.e. 15%, whereas, it contributes around 2% Patents (innovative productivity) on global scale. Many studies have come forward interestingly within scientific and academic domains in the form of measurement of scientific performance, however, development of productivity indicators and calculation of Scientific Productivity (SP) as a holistic evaluation system is a significant demand. SP, a herculean task is envisaged for productivity analysis and would submit significant factors towards fabricating an effective measurement engine in a holistic manner viable for an individual and organization, being supplementary to each other. This review projects the significance of performance measurement system in R&D through identification and standardization of key parameters. It also includes emphasis on inclusion of standardized parameters, effective for performance measurement which is applicable for scientists, technical staff as well as lab as a facility. This review aims at providing an insight to the evaluators, policy makers, and high level scientific panels to stimulate the scientific intellects on identified indicators so that their work proceeds to generate productive outcome contributing to the economic growth. Copyright© Bentham Science

Heating, Ventilation, and Air Conditioning Design Strategy for a Hot-Humid Production Builder

Energy Technology Data Exchange (ETDEWEB)

Kerrigan, P. [Building Science Corporation, Somerville, MA (United States)

2014-03-01

Building Science Corporation (BSC) worked directly with the David Weekley Homes - Houston division to develop a cost-effective design for moving the HVAC system into conditioned space. In addition, BSC conducted energy analysis to calculate the most economical strategy for increasing the energy performance of future production houses in preparation for the upcoming code changes in 2015. This research project addressed the following questions: 1. What is the most cost effective, best performing and most easily replicable method of locating ducts inside conditioned space for a hot-humid production home builder that constructs one and two story single family detached residences? 2. What is a cost effective and practical method of achieving 50% source energy savings vs. the 2006 International Energy Conservation Code for a hot-humid production builder? 3. How accurate are the pre-construction whole house cost estimates compared to confirmed post construction actual cost?

Comparing Effects of Feedstock and Run Conditions on Pyrolysis Products Produced at Pilot-Scale

Energy Technology Data Exchange (ETDEWEB)

Dunning, Timothy C [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gaston, Katherine R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wilcox, Esther [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-01-19

Fast pyrolysis is a promising pathway for mass production of liquid transportable biofuels. The Thermochemical Process Development Unit (TCPDU) pilot plant at NREL is conducting research to support the Bioenergy Technologies Office's 2017 goal of a $3 per gallon biofuel. In preparation for down select of feedstock and run conditions, four different feedstocks were run at three different run conditions. The products produced were characterized extensively. Hot pyrolysis vapors and light gasses were analyzed on a slip stream, and oil and char samples were characterized post run.

Sensor set-up for wireless measurement of automotive rim and wheel parameters in laboratory conditions

Science.gov (United States)

Borecki, M.; Prus, P.; Korwin-Pawlowski, M. L.; Rychlik, A.; Kozubel, W.

2017-08-01

Modern rims and wheels are tested at the design and production stages. Tests can be performed in laboratory conditions and on the ride. In the laboratory, complex and costly equipment is used, as for example wheel balancers and impact testers. Modern wheel balancers are equipped with electronic and electro-mechanical units that enable touch-less measurement of dimensions, including precision measurement of radial and lateral wheel run-out, automatic positioning and application of the counterweights, and vehicle wheel set monitoring - tread wear, drift angles and run-out unbalance. Those tests are performed by on-wheel axis measurements with laser distance meters. The impact tester enables dropping of weights from a defined height onto a wheel. Test criteria are the loss of pressure of the tire and generation of cracks in the wheel without direct impact of the falling weights. In the present paper, a set up composed of three accelerometers, a temperature sensor and a pressure sensor is examined as the base of a wheel tester. The sensor set-up configuration, on-line diagnostic and signal transmission are discussed.

Productive characteristics of age-3 brood brown trout (Salmo trutta reared in the conditions industrial aquaculture

Directory of Open Access Journals (Sweden)

L. Haloyan

2017-03-01

Full Text Available Purpose. Study and analysis of productive and reproductive parameters of brood brown trout reared in the conditions of industrial aquaculture with the use of feeding with specialized artificial feeds. Methodology. Fish rearing was performed using a technology traditional for rainbow trout. Biological evaluation of fish was performed on live material according to the scheme developed by I.F. Pravdin (1966 for salmonids. Fish were anesthetized with “Propiscin”. Metric parameters were measured with the aid of a ruler and caliper. Fish weight was determined on electronic balances. Eggs were preserved in a 4% formalin solution, weight of individual eggs was determined with the aid of torsion balances, egg diameter with a caliper. The duration of spermatozoid motility in males was determined under a microscope under 10X40 magnification with the aid of a stopwatch, sperm concentration was determined in a Goriaev chamber. Multiple regression analysis was performed in JMP IN 4 (SAS Institute. The factor was considered significant if р <0.05. Findings. Brood brown trout reared on specialized artificial feeds had following productive parameters: mean body weight of age-3 fish was 458 g in males and 453 g in females. Mean working fecundity of age-3 fish as 1847 eggs, mean relative working fecundity was 3971 eggs, the mean qualitative parameters of which were: weight of 61.5 g, diameter of 74.7 mm. The reproductive characteristics of age-3 males was high – mean fecundity was 1391 million sperm cells, their motility was 35 sec. Originality. For the first time we reared a stock of brood brown trout in industrial conditions with the use of feeding with specialized artificial feeds. Practical value. The obtained results are a component of the development of a complex technology of salmonid fish rearing with an objective to broad the assortment of valuable gourmet products and to justify the measures on artificial reproduction of brown trout in rivers of

The equipment for low radioactivity measurements in industrial and field conditions

International Nuclear Information System (INIS)

Malik, R.; Owczarczyk, A.; Szpilowski, S.; Zenczykiewicz, Z.

1992-01-01

The equipment for low radioactivity measurements in industrial and field conditions has been worked out. Three scintillation detectors applied work in coincidence system. Their scintillation crystals are divided one to another by lead shieldings. All measuring system is situated in a lead container with lead cover. The measuring vessel fills practically all free volume of the lead container. Their shape ensures the best possible measurement geometry. (author). 3 figs

Local conditional entropy in measure for covers with respect to a fixed partition

Science.gov (United States)

Romagnoli, Pierre-Paul

2018-05-01

In this paper we introduce two measure theoretical notions of conditional entropy for finite measurable covers conditioned to a finite measurable partition and prove that they are equal. Using this we state a local variational principle with respect to the notion of conditional entropy defined by Misiurewicz (1976 Stud. Math. 55 176–200) for the case of open covers. This in particular extends the work done in Romagnoli (2003 Ergod. Theor. Dynam. Syst. 23 1601–10), Glasner and Weiss (2006 Handbook of Dynamical Systems vol 1B (Amsterdam: Elsevier)) and Huang et al (2006 Ergod. Theor. Dynam. Syst. 26 219–45).

Molecular Identification of a Newly Isolated Bacillus subtilis BI19 and Optimization of Production Conditions for Enhanced Production of Extracellular Amylase.

Science.gov (United States)

Dash, Biplab Kumar; Rahman, M Mizanur; Sarker, Palash Kumar

2015-01-01

A study was carried out with a newly isolated bacterial strain yielding extracellular amylase. The phylogenetic tree constructed on the basis of 16S rDNA gene sequences revealed this strain as clustered with the closest members of Bacillus sp. and identified as Bacillus subtilis BI19. The effect of various fermentation conditions on amylase production through shake-flask culture was investigated. Rice flour (1.25%) as a cheap natural carbon source was found to induce amylase production mostly. A combination of peptone and tryptone as organic and ammonium sulfate as inorganic nitrogen sources gave highest yield. Maximum production was obtained after 24 h of incubation at 37 °C with an initial medium pH 8.0. Addition of surfactants like Tween 80 (0.25 g/L) and sodium lauryl sulfate (0.2 g/L) resulted in 28% and 15% increase in enzyme production, respectively. Amylase production was 3.06 times higher when optimized production conditions were used. Optimum reaction temperature and pH for crude amylase activity were 50 °C and 6.0, respectively. The crude enzyme showed activity and stability over a fair range of temperature and pH. These results suggest that B. subtilis BI19 could be exploited for production of amylase at relatively low cost and time.

A Novel Approach to Measuring Muscle Mechanics in Vehicle Collision Conditions

Directory of Open Access Journals (Sweden)

Simon Krašna

2017-06-01

Full Text Available The aim of the study was to evaluate a novel approach to measuring neck muscle load and activity in vehicle collision conditions. A series of sled tests were performed on 10 healthy volunteers at three severity levels to simulate low-severity frontal impacts. Electrical activity—electromyography (EMG—and muscle mechanical tension was measured bilaterally on the upper trapezius. A novel mechanical contraction (MC sensor was used to measure the tension on the muscle surface. The neck extensor loads were estimated based on the inverse dynamics approach. The results showed strong linear correlation (Pearson’s coefficient = 0.821 between the estimated neck muscle load and the muscle tension measured with the MC sensor. The peak of the estimated neck muscle force delayed 0.2 ± 30.6 ms on average vs. the peak MC sensor signal compared to the average delay of 61.8 ± 37.4 ms vs. the peak EMG signal. The observed differences in EMG and MC sensor collected signals indicate that the MC sensor offers an additional insight into the analysis of the neck muscle load and activity in impact conditions. This approach enables a more detailed assessment of the muscle-tendon complex load of a vehicle occupant in pre-impact and impact conditions.

LHCb: Measurement of $D^{\\pm}$ Production Asymmetry at LHCb

CERN Multimedia

Xing, Zhou

2012-01-01

Heavy quark production in 7 TeV pp collisions at the LHC need not be flavour symmetric. Here the production asymmetry, $A_p$ , between $D_s^+$ and $D_s^-$ mesons is measured using the $\\phi\\pi$ decay mode. The difference between $\\pi^+$ and $\\pi^-$ detection efficiencies is measured using the ratio of fully reconstructed to partially reconstructed $D^*$ decays. Using 1 fb$^{-1}$ of data collected with the LHCb detector, we find $A_p = (-0.39 \\pm 0.22 \\pm 0.08)$%.

Conditions for industrial production

DEFF Research Database (Denmark)

Jensen, Karsten Ingerslev; Schultz, Jørgen Munthe; Brauer, H.

1996-01-01

The possibility of an industrial aerogel glazing production is discussed with respect to sample size, sales volume and prices. Different ways of an industrial assembling line is outlined and the total costs of a 1 square meter aerogel glazing is calculated.......The possibility of an industrial aerogel glazing production is discussed with respect to sample size, sales volume and prices. Different ways of an industrial assembling line is outlined and the total costs of a 1 square meter aerogel glazing is calculated....

Guidelines for measuring the physical, chemical, and biological condition of wilderness ecosystems

Science.gov (United States)

Douglas G Fox; J. Christopher Bernabo; Betsy Hood

1987-01-01

Guidelines include a large number of specific measures to characterize the existing condition of wilderness resources. Measures involve the atmospheric environment, water chemistry and biology, geology and soils, and flora. Where possible, measures are coordinated with existing long-term monitoring programs. Application of the measures will allow more effective...

A new metric for measuring condition in large predatory sharks.

Science.gov (United States)

Irschick, D J; Hammerschlag, N

2014-09-01

A simple metric (span condition analysis; SCA) is presented for quantifying the condition of sharks based on four measurements of body girth relative to body length. Data on 104 live sharks from four species that vary in body form, behaviour and habitat use (Carcharhinus leucas, Carcharhinus limbatus, Ginglymostoma cirratum and Galeocerdo cuvier) are given. Condition shows similar levels of variability among individuals within each species. Carcharhinus leucas showed a positive relationship between condition and body size, whereas the other three species showed no relationship. There was little evidence for strong differences in condition between males and females, although more male sharks are needed for some species (e.g. G. cuvier) to verify this finding. SCA is potentially viable for other large marine or terrestrial animals that are captured live and then released. © 2014 The Fisheries Society of the British Isles.

Importance and condition of forage crops seed production in agriculture of the Republic of Serbia

OpenAIRE

Đokić Dragoslav; Terzić Dragan; Milenković Jasmina; Dinić Bora; Anđelković Bojan; Stanisavljević Rade; Barać Saša

2013-01-01

For contemporary and economical livestock production, especially cattle and sheep raising, it is necessary to achieve high production of livestock feed while reducing production costs. Improving the production of perennial grasses and legumes creates a good basis for the development of livestock production in different agro-ecological conditions of Serbia. It also establishes a link between farming and animal husbandry, which is of particular importance for the preservation and higher fertili...

Product Quality and Worker Quality

OpenAIRE

Abowd, John M; Kramarz, Francis

1995-01-01

We study the relation between product quality and worker quality using an economic model that, under certain conditions, provides a direct link between product price, product quality and work-force quality. Our measures of product quality are the evolution in the detailed product price relative to its product group, and the level of the product price relative to this group. Our worker quality measures are the firm's average person effect and personal characteristics effect from individual wag...

Product Quality and Worker Quality

OpenAIRE

John M. ABOWD; Françis KRAMARZ; Antoine MOREAU

1996-01-01

We study the relation between product quality and worker quality using an economic model that, under certain conditions, provides a direct link between product price, product quality and work force quality. Our measures of product quality are the evolution in the detailed product price relative to its product group and the level of the product price relative to this group. Our worker quality measures are the firm's average person effect and personal characteristics effect from individual wage...

Method s for Measuring Productivity in Libraries and Information Centres

Directory of Open Access Journals (Sweden)

Mohammad Alaaei

2009-04-01

Full Text Available   Within Information centers, productivity is the result of optimal and effective use of information resources, service quality improvement, increased user satisfaction, pleasantness of working environment, increased motivation and enthusiasm of staff to work better. All contribute to the growth and development of information centers. Thus these centers would need to be familiar with methods employed in productivity measurement. Productivity is one of the criteria for evaluating system performance. In the past decades particular emphasis has been placed on measurement and improvement of human resource, creativity, innovation and expert analysis. Contemplation and efforts made towards identification of problems and issues and new means to make more useful and better resource management is the very definition of productivity. Simply put, productivity is the relationship between system output and the elements garnered to produce these outputs. The causality between variables and factors impacting on productivity is very complex. In information centers, given the large volume of elements involved, it seems necessary to increase efficiency and productivity

A comparison of GC-FID and PTR-MS toluene measurements in ambient air under conditions of enhanced monoterpene loading

Directory of Open Access Journals (Sweden)

J. L. Ambrose

2010-07-01

Full Text Available Toluene was measured using both a gas chromatographic system (GC, with a flame ionization detector (FID, and a proton transfer reaction-mass spectrometer (PTR-MS at the AIRMAP atmospheric monitoring station Thompson Farm (THF in rural Durham, NH during the summer of 2004. Simultaneous measurements of monoterpenes, including α- and β-pinene, camphene, Δ ³-carene, and d-limonene, by GC-FID demonstrated large enhancements in monoterpene mixing ratios relative to toluene, with median and maximum enhancement ratios of ~2 and ~30, respectively. A detailed comparison between the GC-FID and PTR-MS toluene measurements was conducted to test the specificity of PTR-MS for atmospheric toluene measurements under conditions often dominated by biogenic emissions. We derived quantitative estimates of potential interferences in the PTR-MS toluene measurements related to sampling and analysis of monoterpenes, including fragmentation of the monoterpenes and some of their primary carbonyl oxidation products via reactions with H₃O⁺, O₂⁺ and NO⁺ in the PTR-MS drift tube. The PTR-MS and GC-FID toluene measurements were in good quantitative agreement and the two systems tracked one another well from the instrumental limits of detection to maximum mixing ratios of ~0.5 ppbv. A correlation plot of the PTR-MS versus GC-FID toluene measurements was described by the least squares regression equation y=(1.13± 0.02x−(0.008±0.003 ppbv, suggesting a small ~13% positive bias in the PTR-MS measurements. The bias corresponded with a ~0.055 ppbv difference at the highest measured toluene level. The two systems agreed quantitatively within the combined 1σ measurement precisions for 60% of the measurements. Discrepancies in the measured mixing ratios were not well correlated with enhancements in the monoterpenes. Better quantitative agreement between the two systems was obtained by

Corrosion-product transport, oxidation state and remedial measures

International Nuclear Information System (INIS)

Sawicki, J.A.; Brett, M.E.; Tapping, R.L.

1998-01-01

The issues associated with monitoring and controlling corrosion-product transport (CPT) in the balance-of-plant (BOP) and steam generators (SG) of CANDU stations are briefly reviewed. The efforts are focused on minimizing corrosion of carbon steel, which is used extensively in the CANDU primary and secondary systems. Emphasis is placed on the corrosion-product oxidation state as a monitor of water chemistry effectiveness, and as a monitor of system corrosion effects. The discussion is based mostly on the results and observations from Ontario Hydro plants, and their comparisons with PWRs. The effects of low oxygen and elevated hydrazine chemistry are reviewed, as well as the effects of lay-up and various start-up conditions. Progress in monitoring electrochemical potential (ECP) at Ontario Hydro plants and its relationship to the oxidation state of corrosion products is reviewed. Observations on corrosion-product transport on the primary side of steam generators are also discussed. (author)

Effect of bioconversion conditions on vanillin production by Amycolatopsis sp. ATCC 39116 through an analysis of competing by-product formation.

Science.gov (United States)

Ma, Xiao-kui; Daugulis, Andrew J

2014-05-01

This study investigated the effects of transformation conditions such as initial pH, the initial concentration of glucose and yeast extract in the medium, and the separate addition of ferulic acid and vanillic acid, on the production of vanillin through an analysis of competing by-product formation by Amycolatopsis sp. ATCC 39116. The extent and nature of by-product formation and vanillin yield were affected by initial pH and different initial concentrations of glucose and yeast extract in the medium, with a high yield of vanillin and high cell density obtained at pH 8.0, 10 g/l glucose, and 8 g/l yeast extract. High concentrations of ferulic acid were found to negatively affect cell density. Additional supplementation of 100 mg/l vanillic acid, a metabolically linked by-product, was found to result in a high concentration of vanillin and guaiacol, an intermediate of vanillin. Via an analysis of the effect of these transformation conditions on competing by-product formation, high concentrations of ferulic acid were transformed with a molar yield to vanillin of 96.1 and 95.2 %, by Amycolatopsis sp. ATCC 39116 and Streptomyces V1, respectively, together with a minor accumulation of by-products. These are among the highest performance values reported in the literature to date for Streptomyces in batch cultures.

Theoretical framework on selected core issues on conditions for productive learning in networked learning environments

DEFF Research Database (Denmark)

Dirckinck-Holmfeld, Lone; Svendsen, Brian Møller; Ponti, Marisa

The report documents and summarises the elements and dimensions that have been identified to describe and analyse the case studies collected in the Kaleidoscope Jointly Executed Integrating Research Project (JEIRP) on Conditions for productive learning in network learning environments.......The report documents and summarises the elements and dimensions that have been identified to describe and analyse the case studies collected in the Kaleidoscope Jointly Executed Integrating Research Project (JEIRP) on Conditions for productive learning in network learning environments....

Conditioning a segmented stem profile model for two diameter measurements

Science.gov (United States)

Raymond L. Czaplewski; Joe P. Mcclure

1988-01-01

The stem profile model of Max and Burkhart (1976) is conditioned for dbh and a second upper stem measurement. This model was applied to a loblolly pine data set using diameter outside bark at 5.3m (i.e., height of 17.3 foot Girard form class) as the second upper stem measurement, and then compared to the original, unconditioned model. Variance of residuals was reduced...

Measuring excess capital capacity in agricultural production

NARCIS (Netherlands)

Zhengfei, G.; Kumbhakar, S.C.; Myers, R.J.; Oude Lansink, A.G.J.M.

2009-01-01

We introduce the concept "excess capital capacity" and employ a stochastic input requirement frontier to measure excess capital capacity in agricultural production. We also propose a two-step estimation method that allows endogenous regressors in stochastic frontier models. The first step uses

Vaporization of low-volatile fission products under severe CANDU reactor accident conditions

International Nuclear Information System (INIS)

Lewis, B.J.; Corse, B.J.; Thompson, W.T.; Kaye, M.H.; Iglesias, F.C.; Elder, P.; Dickson, R.; Liu, Z.

1997-01-01

An analytical model has been developed to describe the release behaviour of low-volatile fission products from uranium dioxide fuel under severe reactor accident conditions. The effect of the oxygen potential on the chemical form and volatility of fission products is determined by Gibbs-energy minimization. The release kinetics are calculated according to the rate-controlling step of diffusional transport in the fuel matrix or fission product vaporization from the fuel surface. The effect of fuel volatilization (i.e., matrix stripping) on the release behaviour is also considered. The model has been compared to data from an out-of-pile annealing experiment performed in steam at the Chalk River Laboratories. (author)

Measuring intracellular redox conditions using GFP-based sensors

DEFF Research Database (Denmark)

Björnberg, Olof; Ostergaard, Henrik; Winther, Jakob R

2006-01-01

Recent years have seen the development of methods for analyzing the redox conditions in specific compartments in living cells. These methods are based on genetically encoded sensors comprising variants of Green Fluorescent Protein in which vicinal cysteine residues have been introduced at solvent......-exposed positions. Several mutant forms have been identified in which formation of a disulfide bond between these cysteine residues results in changes of their fluorescence properties. The redox sensors have been characterized biochemically and found to behave differently, both spectroscopically and in terms...... of redox properties. As genetically encoded sensors they can be expressed in living cells and used for analysis of intracellular redox conditions; however, which parameters are measured depends on how the sensors interact with various cellular redox components. Results of both biochemical and cell...

Measurement of charmed particle production in hadronic reactions

CERN Multimedia

2002-01-01

The aim of the experiment is to measure the production cross-section for charmed particles in hadronic reactions, study their production mechanism, and search for excited charmed hadrons.\\\\ \\\\ Charmed Mesons and Baryons will be measured in $\\pi$ and $p$ interactions on Beryllium between 100 and 200 GeV/c. The trigger will be on an electron from the leptonic decay of one charmed particle by signals from the Cerenkov counter (Ce), the electron trigger calorimeter (eCal), scintillation counters, and proportional wire chambers. The accompanying charmed particle will be measured via its hadronic decay in a two-stage magnetic spectrometer with drift chambers (arms 2, 3a, 3b, 3c), two large-area multicell Cerenkov counters (C2, C3) and a large-area shower counter ($\\gamma$-CAL). The particles which can be measured and identified include $\\gamma, e, \\pi^{\\pm}, \\pi^{0}, K^{\\pm}, p, \\bar{p}$ so that a large number of hadronic decay modes of charmed particles can be studied. \\\\ \\\\ A silicon counter telescope with 5 $\\m...

Effect of the Characters of Chitosans Used and Regeneration Conditions on the Yield and Physicochemical Characteristics of Regenerated Products

Directory of Open Access Journals (Sweden)

Chu Hsi Hsu

2015-04-01

Full Text Available The objective of this study was to explore the effect of the character of chitosans used, and the regeneration conditions employed on, the yield and physicochemical characteristics of regenerated products. Different concentrations of acetic acid were used to dissolve chitosans of 61.7% and 94.9% degree of deacetylation (DD, and weight-average molecular weight (Mw of 176 and 97 kDa, respectively; they were then precipitated with an 8 N NaOH solution, followed by washing and neutral and freeze drying to get the regenerated products. Yields of regenerated products and their physicochemical properties, such as ash content, bulk density, Mw, polydispersity index (PDI, DD, and crystallinity were measured. A higher concentration of acetic acid used resulted in a higher yield. The purity of the regenerated product increased significantly, whereas the bulk density and crystallinity decreased significantly after regeneration. The regeneration process showed its merits of narrowing down the PDI of regenerated products. The DD and structure of chitosan was changed insignificantly after the regeneration process.

Disintegration of the agricultural by-product wheat bran under subcritical conditions.

Science.gov (United States)

Reisinger, Michael; Tirpanalan, Özge; Pruksasri, Suwattana; Kneifel, Wolfgang; Novalin, Senad

2018-02-10

The disintegration of destarched wheat bran in water and sulfuric acid (pH 3) under subcritical conditions (275-300 °C) and at short reaction times (1-4 min) was investigated. A cascade process comprising a stepwise separation of the liquid was applied to reduce the formation of undesired degradation products. The highest degree of biomass disintegration (67% dry mass solubilization) was achieved by application of a cascade process at 275 °C (pH 3). Regarding the dissolution of carbohydrates (monomeric and oligomeric form), the total glucose yields remained below 60%, while the total xylose and arabinose yields were about 76% and 67%. Approximately 74% of the protein and 95% of the mineral fraction could be extracted. The application of the cascade process enabled a substantially reduced formation of degradation products. When operating hydrothermally and subcritically in order to avoid some problematic aspects of a biorefinery, an extensive disintegration and monomerization of wheat bran and its constituents remains difficult even under the tested conditions (300 °C, pH 3). However, the applied cascade process proved to be useful to increase the yields and to substantially reduce the formation of undesired degradation products. Despite this fact, increased water consumption has to be conceded. © 2018 Society of Chemical Industry. © 2018 Society of Chemical Industry.

Technical Note: Quantification of interferences of wet chemical HONO LOPAP measurements under simulated polar conditions

Directory of Open Access Journals (Sweden)

J. Kleffmann

2008-11-01

Full Text Available In the present pilot study, an optimized LOPAP instrument (LOng Path Absorption Photometer for the detection of nitrous acid (HONO in the atmosphere (DL 0.2 pptV was tested at the high alpine research station Jungfraujoch at 3580 m altitude in the Swiss Alps under conditions comparable to polar regions. HONO concentrations in the range <0.5–50 pptV with an average of 7.5 pptV were observed at the Jungfraujoch. The diurnal profiles obtained exhibited clear maxima at noon and minima with very low concentration during the night supporting the proposed photochemical production of HONO. In good agreement with recent measurements at the South Pole, it was demonstrated, that interferences of chemical HONO instruments can significantly influence the measurements and lead to considerable overestimations, especially for low pollution level. Accordingly, the active correction of interferences is of paramount importance for the determination of reliable HONO data.

Environmental Growing Conditions in Five Production Systems Induce Stress Response and Affect Chemical Composition of Cocoa (Theobroma cacao L.) Beans.

Science.gov (United States)

Niether, Wiebke; Smit, Inga; Armengot, Laura; Schneider, Monika; Gerold, Gerhard; Pawelzik, Elke

2017-11-29

Cocoa beans are produced all across the humid tropics under different environmental conditions provided by the region but also by the season and the type of production system. Agroforestry systems compared to monocultures buffer climate extremes and therefore provide a less stressful environment for the understory cocoa, especially under seasonally varying conditions. We measured the element concentration as well as abiotic stress indicators (polyamines and total phenolic content) in beans derived from five different production systems comparing monocultures and agroforestry systems and from two harvesting seasons. Concentrations of N, Mg, S, Fe, Mn, Na, and Zn were higher in beans produced in agroforestry systems with high stem density and leaf area index. In the dry season, the N, Fe, and Cu concentration of the beans increased. The total phenolic content increased with proceeding of the dry season while other abiotic stress indicators like spermine decreased, implying an effect of the water availability on the chemical composition of the beans. Agroforestry systems did not buffer the variability of stress indicators over the seasons compared to monocultures. The effect of environmental growing conditions on bean chemical composition was not strong but can contribute to variations in cocoa bean quality.

Measurements of the Vector boson production with the ATLAS Detector

CERN Document Server

Lapertosa, Alessandro; The ATLAS collaboration

2017-01-01

Measurements of the Drell-Yan production of W and Z/γ bosons at the LHC provide a benchmark of our understanding of perturbative QCD and probe the proton structure in a unique way. The ATLAS collaboration has performed new high precision measurements at center-of-mass energies of 7 TeV. The measurements are performed for W+, W− and Z/γ bosons integrated and as a function of the boson or lepton rapidity and the Z/γ∗ mass. Unprecedented precision is reached and strong constraints on Parton Distribution functions, in particular the strange density are found. Z cross sections are also measured at a center-of-mass energies of 8 TeV and 13 TeV, and cross-section ratios to the top-quark pair production have been derived. This ratio measurement leads to a cancellation of systematic effects and allows for a high precision comparison to the theory predictions. The production of jets in association with vector bosons is a further important process to study perturbative QCD in a multi-scale environment. The ATLAS ...

Measurements of the vector boson production with the ATLAS detector

CERN Document Server

Lapertosa, Alessandro; The ATLAS collaboration

2017-01-01

Measurements of the Drell-Yan production of $W$ and $Z$ bosons at the LHC provide a benchmark of our understanding of perturbative QCD and probe the proton structure in a unique way. The ATLAS collaboration has performed new high precision measurements at center-of-mass energies of 7 TeV. The measurements are performed for $W^+$, $W^{-}$ and $Z$ bosons integrated and as a function of the boson or lepton rapidity and the $Z$ mass. Unprecedented precision is reached and strong constraints on Parton Distribution Functions, in particular the strange density are found. $Z$ boson cross sections are also measured at a center-of-mass energies of 8 TeV and 13 TeV, and cross-section ratios to the top-quark pair production have been derived. This ratio measurement leads to a cancellation of systematic effects and allows for a high precision comparison to the theory predictions. The production of jets in association with vector bosons is a further important process to study perturbative QCD in a multi-scale environment. ...

Improved optimum condition for recovery and measurement of 210 ...

African Journals Online (AJOL)

The aim of this study was to determine the optimum conditions for deposition of 210Po and evaluate the accuracy and precision of the results for its determination in environmental samples. To improve the technique for measurement of polonium-210(210Po) in environmental samples. The optimization of five factors (volume ...

Stability and oxidation products of hydrolysable tannins in basic conditions detected by HPLC/DAD-ESI/QTOF/MS.

Science.gov (United States)

Tuominen, Anu; Sundman, Terhi

2013-01-01

Hydrolysable tannins occur in plants that are used for food or medicine by humans or herbivores. Basic conditions can alter the structures of tannins, that is, the oxidation of phenolic groups can lead to the formation of toxic quinones. Previously, these labile quinones and other oxidation products have been studied with colorimetric or electron paramagnetic resonance methods, which give limited information about products. To study the stability and oxidation products of hydrolysable tannins in basic conditions using HPLC with a diode-array detector (DAD) combined with electrospray ionisation (ESI) and quadrupole time-of-flight (QTOF) MS. Three galloyl glucoses, four galloyl derivatives with different polyols and three ellagitannins were purified from plants. The incubation reactions of tannins were monitored by HPLC/DAD at five pH values and in reduced oxygen conditions. Reaction products were identified based on UV spectra and mass spectral fragmentation obtained with the high-resolution HPLC/DAD-ESI/QTOF/MS. The use of a base-resistant HPLC column enabled injections without the sample pre-treatment and thus detection of short-lived products. Hydrolysable tannins were unstable in basic conditions and half-lives were mostly less than 10 min at pH 10. Degradation rates were faster at pH 11 but slower at milder pH. The HPLC analyses revealed that various products were formed and identified to be the result of hydrolysis, deprotonation and oxidation. Interestingly, the main hydrolysis product was ellagic acid; it was also formed from galloyl glucoses that do not contain oxidatively coupled galloyl groups in their initial structures. HPLD/DAD-ESI/QTOF/MS was an efficient method for the identification of polyphenol oxidation products and showed how different pH conditions determine the fate of hydrolysable tannins. Copyright © 2013 John Wiley & Sons, Ltd.

Effect of Feed Additives on Productivity and Campylobacter spp. Loads in Broilers Reared under Free Range Conditions.

Science.gov (United States)

Guyard-Nicodème, Muriel; Huneau-Salaün, Adeline; Tatone, Fabrizio A; Skiba, Fabien; Quentin, Maxime; Quesne, Ségolène; Poezevara, Typhaine; Chemaly, Marianne

2017-01-01

The poultry reservoir, especially broiler meat, is generally recognized as one of the most-important sources for human Campylobacteriosis. The measures to control Campylobacter targeted essentially the primary production level. The aim of this work was to evaluate the effectiveness of different treatments against natural Campylobacter colonization in a French experimental farm of free-range broilers during the whole rearing period. Five commercial products and a combination of two of them were tested and all the products were added to feed or to water at the dose recommended by the suppliers. Campylobacter loads in caeca and on carcasses of broilers at the slaughter were determined by culture methods. Natural contamination of the flock occurred at the end of the indoor rearing period between day 35 and day 42. At day 42, the multispecies probiotic added to the feed reduced the contamination of 0.55 log 10 CFU/g ( p = 0.02) but was not significant ( p > 0.05) at the end of rearing at day 78. However, another treatment, a combination of a cation exchange clay-based product in feed and an organic acid mixture (formic acid, sodium formate, lactic acid, propionic acid) in water, led to a slight but significant reduction of 0.82 ± 0.25 log 10 CFU/g ( p = 0.02) compared to the control group at day 78. Testing this combination in field conditions in several flocks is needed to determine if it is biologically relevant and if it could be a valuable measure to reduce Campylobacter in broiler flocks.

Effect of Feed Additives on Productivity and Campylobacter spp. Loads in Broilers Reared under Free Range Conditions

Directory of Open Access Journals (Sweden)

Muriel Guyard-Nicodème

2017-05-01

Full Text Available The poultry reservoir, especially broiler meat, is generally recognized as one of the most-important sources for human Campylobacteriosis. The measures to control Campylobacter targeted essentially the primary production level. The aim of this work was to evaluate the effectiveness of different treatments against natural Campylobacter colonization in a French experimental farm of free-range broilers during the whole rearing period. Five commercial products and a combination of two of them were tested and all the products were added to feed or to water at the dose recommended by the suppliers. Campylobacter loads in caeca and on carcasses of broilers at the slaughter were determined by culture methods. Natural contamination of the flock occurred at the end of the indoor rearing period between day 35 and day 42. At day 42, the multispecies probiotic added to the feed reduced the contamination of 0.55 log10 CFU/g (p = 0.02 but was not significant (p > 0.05 at the end of rearing at day 78. However, another treatment, a combination of a cation exchange clay-based product in feed and an organic acid mixture (formic acid, sodium formate, lactic acid, propionic acid in water, led to a slight but significant reduction of 0.82 ± 0.25 log10 CFU/g (p = 0.02 compared to the control group at day 78. Testing this combination in field conditions in several flocks is needed to determine if it is biologically relevant and if it could be a valuable measure to reduce Campylobacter in broiler flocks.

Does Input Quality Drive Measured Differences in Firm Productivity?

DEFF Research Database (Denmark)

Fox, Jeremy T.; Smeets, Valerie Anne Rolande

2011-01-01

One explanation for productivity dispersion is that the quality of inputs differs across firms. We add labor market history variables such as experience and firm and industry tenure, as well as general human capital measures such as schooling and sex. Adding these variables decreases the ratio...... of the 90th to 10th productivity quantiles from 3.27 to 2.68 across eight Danish manufacturing and service industries. We also use the wage bill and worker fixed effects. We find that the wage bill explains as much dispersion as human capital measures....

The Production Measurement Model of Open Pit Mine Based on Truck Operation Diagram

Directory of Open Access Journals (Sweden)

Sun Xiao-Yu

2016-01-01

Full Text Available Conventional production measurement of truck dispatching system in open pit mine has not been effectively expressed by a mathematical model, which brings a negative effect on the subsequent data mining and a compatibility issue to apply the production measurement with fixed assignment of truck. In this study, based on the proposed concept that truck is not only the carrier of transport material, but also act as the bridges and linkages between the loading sites and the unloading sites, a new truck operation diagram was established, which was further developed to a basic data matrix and a production measurement model. The new model allowed to calculatethe production measurement of the transport, loading, unloading, material and etc, respectively, as well as with any calculation in combination of more than one factor as needed.It solved the compatibility issue between conventional production measurement and the production measurement of fixed assignment of truck with good practical results.

Molecular Identification of a Newly Isolated Bacillus subtilis BI19 and Optimization of Production Conditions for Enhanced Production of Extracellular Amylase

Directory of Open Access Journals (Sweden)

Biplab Kumar Dash

2015-01-01

Full Text Available A study was carried out with a newly isolated bacterial strain yielding extracellular amylase. The phylogenetic tree constructed on the basis of 16S rDNA gene sequences revealed this strain as clustered with the closest members of Bacillus sp. and identified as Bacillus subtilis BI19. The effect of various fermentation conditions on amylase production through shake-flask culture was investigated. Rice flour (1.25% as a cheap natural carbon source was found to induce amylase production mostly. A combination of peptone and tryptone as organic and ammonium sulfate as inorganic nitrogen sources gave highest yield. Maximum production was obtained after 24 h of incubation at 37°C with an initial medium pH 8.0. Addition of surfactants like Tween 80 (0.25 g/L and sodium lauryl sulfate (0.2 g/L resulted in 28% and 15% increase in enzyme production, respectively. Amylase production was 3.06 times higher when optimized production conditions were used. Optimum reaction temperature and pH for crude amylase activity were 50°C and 6.0, respectively. The crude enzyme showed activity and stability over a fair range of temperature and pH. These results suggest that B. subtilis BI19 could be exploited for production of amylase at relatively low cost and time.

HYDROLOGIC CONDITIONS AFFECTING THE TROPOSPHERIC FLUX OF VINCLOZOLIN AND ITS DEGRADATION PRODUCTS

Science.gov (United States)

A laboratory chamber was used to determine hydrologic conditions that lead to the tropospheric flux of a suspected anti-androgenic dicarboximide fungicide, vinclozolin (3-(3,5-dichlorophenyl)-5-methyl-5-vinyl-oxzoli-dine-2,4-dione) and three degradation products from sterilized...

The application of conditioning paradigms in the measurement of pain.

Science.gov (United States)

Li, Jun-Xu

2013-09-15

Pain is a private experience that involves both sensory and emotional components. Animal studies of pain can only be inferred by their responses, and therefore the measurement of reflexive responses dominates the pain literature for nearly a century. It has been argued that although reflexive responses are important to unveil the sensory nature of pain in organisms, pain affect is equally important but largely ignored in pain studies primarily due to the lack of validated animal models. One strategy to begin to understand pain affect is to use conditioning principles to indirectly reveal the affective condition of pain. This review critically analyzed several procedures that are thought to measure affective learning of pain. The procedures regarding the current knowledge, the applications, and their advantages and disadvantages in pain research are discussed. It is proposed that these procedures should be combined with traditional reflex-based pain measurements in future studies of pain, which could greatly benefit both the understanding of neural underpinnings of pain and preclinical assessment of novel analgesics. © 2013 Elsevier B.V. All rights reserved.

Measurement of fission product release during LWR fuel failure

International Nuclear Information System (INIS)

Osetek, D.J.; King, J.J.

1979-01-01

The PBF is a specialized test reactor consisting of an annular core and a central test space 21 cm in diameter and 91 cm high. A test loop circulates coolant through the central experimental section at typical power reactor conditions. Light-water-reactor-type fuel rods are exposed to power bursts simulating reactivity insertion transients, and to power-cooling-mismatch conditions during which the rods are allowed to operate in film boiling. Fission product concentrations in the test loop coolant are continuously monitored during these transients by a Ge(Li) detector based gamma spectrometer. Automatic batch processing of pulse height spectra results in a list of radionuclide concentrations present in the loop coolant as a function of time during the test. Fission product behavior is then correlated to test parameters and posttest examination of the fuel rods. Data are presented from Test PCM-1

The influence of local effects on thermal sensation under non-uniform environmental conditions — Gender differences in thermophysiology, thermal comfort and productivity during convective and radiant cooling

DEFF Research Database (Denmark)

Schellen, L.; Loomans, M.G.L.C.; de Wit, M.H.

2012-01-01

, thermal comfort and productivity in response to thermal non-uniform environmental conditions. Twenty healthy subjects (10 males and 10 females, age 20–29years) were exposed to two different experimental conditions: a convective cooling situation (CC) and a radiant cooling situation (RC). During...... the experiments physiological responses, thermal comfort and productivity were measured. The results show that under both experimental conditions the actual mean thermal sensation votes significantly differ from the PMV-index; the subjects are feeling colder than predicted. Furthermore, the females are more...... of the occupants. Non-uniform thermal conditions, which may occur due to application of high temperature cooling systems, can be responsible for discomfort. Contradictions in literature exist regarding the validity of the often used predicted mean vote (PMV) index for both genders, and the index is not intended...

Diatom production in the marine environment : implications for larval fish growth and condition

DEFF Research Database (Denmark)

St. John, Michael; Clemmesen, C.; Lund, T.

2001-01-01

To test the effects of diatom production on larval fish growth and condition. laboratory experiments were performed with larval North Sea cod reared on different algal food chains. These food chains were based on cultures of (a) the diatoms Skeletonema costatum and Thalassiosira weissflogii: (b....../omega6 fatty acids in the algal source had no significant effect. The highest and lowest growth rates were observed in food chains based on H. triquetra and T. weissflogii. respectively (means for days 14-16 of 4.0 and - 4.7). The mixed diatom/dinoflagellate diet resulted in inter- mediate growth rates...... and condition. Regressions of growth rates against EPA and DHA content indicated no inhibitory effect of diatom production on growth in larval cod...

Effect of body condition score at mating on the reproductive performance of Kivircik sheep under an extensive production system.

Science.gov (United States)

Yilmaz, Murat; Altin, Tufan; Karaca, Orhan; Cemal, Ibrahim; Bardakcioglu, Husnu Erbay; Yilmaz, Onur; Taskin, Turgay

2011-12-01

The aim of this study was to determine the effects of the body condition score (BCS) of ewes before and during the mating season on their reproductive performance under an extensive production system. In this study, 240 Kivircik sheep from the flocks of two breeders were used for over a 2-year period. The flocks were fed under extensive conditions on natural pastures throughout the year. The ewes were synchronized in two different periods, one of which was 45 days before the other. Before the introduction of rams to the ewes, the ewes were weighed after measuring their BCS. Detailed records were kept for every flock in each year. We found significant effects of BCS on pregnancy rate, lambing rate (P < 0.05) and fecundity (P < 0.05). The BCS for the highest pregnancy, lambing rate, and fecundity was determined between 2.01 and 3.00, while the lowest rates for these traits were ≤ 1.50. The highest rates of the pregnancy rate, lambing rate, and fecundity and gestation productivity were 75.9%, 70.9%, 1.11 and 3.34 kg, respectively.

USDA Foreign Agricultural Service overview for operational monitoring of current crop conditions and production forecasts.

Science.gov (United States)

Crutchfield, J.

2016-12-01

The presentation will discuss the current status of the International Production Assessment Division of the USDA ForeignAgricultural Service for operational monitoring and forecasting of current crop conditions, and anticipated productionchanges to produce monthly, multi-source consensus reports on global crop conditions including the use of Earthobservations (EO) from satellite and in situ sources.United States Department of Agriculture (USDA) Foreign Agricultural Service (FAS) International Production AssessmentDivision (IPAD) deals exclusively with global crop production forecasting and agricultural analysis in support of the USDAWorld Agricultural Outlook Board (WAOB) lockup process and contributions to the World Agricultural Supply DemandEstimates (WASE) report. Analysts are responsible for discrete regions or countries and conduct in-depth long-termresearch into national agricultural statistics, farming systems, climatic, environmental, and economic factors affectingcrop production. IPAD analysts become highly valued cross-commodity specialists over time, and are routinely soughtout for specialized analyses to support governmental studies. IPAD is responsible for grain, oilseed, and cotton analysison a global basis. IPAD is unique in the tools it uses to analyze crop conditions around the world, including customweather analysis software and databases, satellite imagery and value-added image interpretation products. It alsoincorporates all traditional agricultural intelligence resources into its forecasting program, to make the fullest use ofavailable information in its operational commodity forecasts and analysis. International travel and training play animportant role in learning about foreign agricultural production systems and in developing analyst knowledge andcapabilities.

Assessment of global precipitation measurement satellite products over Saudi Arabia

Science.gov (United States)

Mahmoud, Mohammed T.; Al-Zahrani, Muhammad A.; Sharif, Hatim O.

2018-04-01

Most hydrological analysis and modeling studies require reliable and accurate precipitation data for successful simulations. However, precipitation measurements should be more representative of the true precipitation distribution. Many approaches and techniques are used to collect precipitation data. Recently, hydrometeorological and climatological applications of satellite precipitation products have experienced a significant improvement with the emergence of the latest satellite products, namely, the Integrated Multi-satellitE Retrievals for Global Precipitation Measurement (GPM) mission (IMERG) products, which can be utilized to estimate and analyze precipitation data. This study focuses on the validation of the IMERG early, late and final run rainfall products using ground-based rain gauge observations throughout Saudi Arabia for the period from October 2015 to April 2016. The accuracy of each IMERG product is assessed using six statistical performance measures to conduct three main evaluations, namely, regional, event-based and station-based evaluations. The results indicate that the early run product performed well in the middle and eastern parts as well as some of the western parts of the country; meanwhile, the satellite estimates for the other parts fluctuated between an overestimation and an underestimation. The late run product showed an improved accuracy over the southern and western parts; however, over the northern and middle parts, it showed relatively high errors. The final run product revealed significantly improved precipitation estimations and successfully obtained higher accuracies over most parts of the country. This study provides an early assessment of the performance of the GPM satellite products over the Middle East. The study findings can be used as a beneficial reference for the future development of the IMERG algorithms.

Enhancing Ethanol Production by Fermentation Using Saccharomyces cereviseae under Vacuum Condition in Batch Operation

Directory of Open Access Journals (Sweden)

A Abdullah

2012-04-01

Full Text Available Ethanol is one of renewable energy, which considered being an excellent alternativeclean-burning fuel to replaced gasoline. In fact, the application of ethanol as fuel still blended withgasoline. The advantages of using ethanol as fuel are that the raw material mostly from renewableresources and the product has low emission which means environmental friendly. Ethanol can beproduced by fermentation of sugars (glucose/fructose. The constraint in the ethanol fermentationbatch or continuous process is the ethanol product inhibition. Inhibition in ethanol productivityand cell growth can be overcome by taking the product continuously from the fermentor. Theprocess can be done by using a vacuum fermentation. The objective of this research is toinvestigate the effect of pressure and glucose concentration in ethanol fermentation. The researchwas conducted in laboratory scale and batch process. Equipment consists of fermentor withvacuum system. The observed responses were dried cells of yeast, concentration of glucose, andconcentration of ethanol. Observations were made every 4 hours during a day of experiment. Theresults show that the formation of ethanol has a growth-associated product characteristic undervacuum operation. Vacuum condition can increase the cell formation productivity and the ethanolformation, as it is compared with fermentation under atmospheric condition. The maximum cellsproductivity and ethanol formation in batch operation under vacuum condition was reached at166.6 mmHg of pressure. The maximum numbers of cells and ethanol formation was reached at141.2 mm Hg of pressure. High initial glucose concentration significantly can affect the productivityand the yield of ethanol.

Experiment on Measurement of Interfacial Tension for Subsurface Conditions of Light Oil from Thailand

Directory of Open Access Journals (Sweden)

Jiravivitpanya Jiramet

2017-01-01

Full Text Available One of enhanced oil recovery techniques to increase oil production is surfactant flooding. Surfactants are considered as effective chemical agents used in oilfield in Thailand. It is used to reduce the interfacial tension (IFT of two fluids and to make them flow easier in the reservoir. In this study, Monoethanolamide (MEA commonly used for carbon dioxide capture, is applied as a surfactant to reduce IFT between oil and brine. Therefore, the aim of this work is to investigate and measure the IFT based on the conditions of subsurface at the oilfield in Thailand. These parameters such as temperature, pressure, salinity as well as the concentration of surfactant are adjusted to investigate the effects on IFT reduction. From the results, it is reported that pressure from 1000 to 2000 psi and temperature varied from 70°C to 90°C can reduce IFT insignificantly. However, salinity and surfactant concentration are the main parameters that impact on the IFT reduction. It can greatly decrease IFT up to 87.13% for surfactant concentration and up to 74.06% for salinity. Finally, the results can be applied to use in the real field for enhanced oil production in Thailand.

Measuring the productivity of university research reactors

International Nuclear Information System (INIS)

Voth, M.H.

1989-01-01

University Research Reactors (URRs) on 33 campuses in the United States provide valuable contributions to academic instruction and research programs. In most cases, there are no alternative diagnostic techniques to supplant the need for a reactor and associated facilities. Since URRs constitute a major financial commitment, it is important that they be operated in a productive manner. Productivity may be defined as the sum of new knowledge generated, existing knowledge transferred to others, and analytical services provided to assist in the generation of new knowledge; another definition of productivity is this sum expressed as a function of the cost incurred. In either case, a consistent measurement is difficult and more qualitative than quantitative. A uniform reporting system has been proposed that defines simplified categories through which meaningful comparisons can be performed

Di-boson production measurements with the ATLAS detector

CERN Document Server

Chevalier, Laurent

2015-01-01

This talk covers the results of the measurements of diboson production cross sections in proton- proton interactions at 7 TeV in 2011 and at 8 TeV in 2012, performed by the ATLAS experiment. The cross sections are measured in phase space regions defined by the decay kinematics, the detector acceptance and then extrapolated to the full phase space. Cross sections for VV (V=W, Z, γ) production in the leptonic or semileptonic channels are compared to (N)NLO predictions of the Standard Model. Kinematic spectra are used to place constraints on anomalous triple-gauge-boson couplings. All cross sections are in agreement with the Standard Model predictions. No experimental evidence is found of anomalous triple-gauge-boson couplings. PACS: 14.70.-e Gauge bosons.

Cavity Ring-Down Spectroscopy for Gaseous Fission Products Trace Measurements in Sodium Fast Reactors

International Nuclear Information System (INIS)

Jacquet, P.; Pailloux, A.; Doizi, D.; Aoust, G.; Jeannot, J.-P.

2013-06-01

Safety and availability are key issues of the generation IV reactors. Hence, the three radionuclide confinement barriers, including fuel cladding, must stay tight during the reactor operation. During the primary gaseous failure, fission products xenon and krypton are released. Their fast and sensitive detection guarantees the first confinement barrier tightness. In the frame of the French ASTRID project, an optical spectroscopy technique - Cavity Ring Down Spectroscopy (CRDS) - is investigated for the gaseous fission products measurement. A dedicated CRDS set-up is needed to detect the rare gases with a commercial laser. Indeed, the CRDS is coupled to a glow discharge plasma, which generates a population of metastable atoms. The xenon plasma conditions are optimized to 110 Pa and 1.3 W (3 mA). The production efficiency of metastable Xe is then 0.8 %, stable within 0.5% during hours. The metastable number density is proportional to the xenon over argon molar fraction. The spectroscopic parameters of the strong 823.16 nm xenon transition are calculated and/or measured in order to optimize the fit of the experimental spectra and make a quantitative measurement of the metastable xenon. The CRDS is coupled to the discharge cell. The laser intensity inside the cavity is limited by the optical saturation process, resulting from the strong optical pumping of the metastable state. The resulting weak CRDS signal requires a fast and very sensitive photodetector. A 600 ppt xenon molar fraction was measured by CRDS. With the present set-up, the detection limits are estimated from the baseline noise to approximately 20 ppt for each even isotope, 60 ppt for the 131 Xe and 55 ppt for the 129 Xe. This sensitivity matches the specifications required for gaseous leak measurement; approximately 100 ppt for 133 Xe (4 GBq/m 3 ) and 10 ppb for stable isotopes. The odd isotopes are selectively measured, whereas the even isotopes overlap, a spectroscopic feature that applies for stable or

Evaluation of Culture Conditions for Tannase Production by Aspergillus niger GH1

Directory of Open Access Journals (Sweden)

Mario Cruz-Hernández

2006-01-01

Full Text Available Extra- and intracellular tannase production by Aspergillus niger GH1 has been evaluated using submerged (SmF and solid-state fermentation (SSF at different temperatures (30, 40 and 50 °C. Effects of initial substrate (tannic acid concentration, incubation time and temperature on tannase production in SSF have been studied. A. niger GH1 produced the highest tannase level (2291 U/L in SSF at 30 °C during the first 20 h of culture at tannic acid concentration of 50 g/L, and under these conditions enzyme production was entirely extracellular. The decline in tannase activity after 20 h of incubation was associated with a concomitant increase in protease activity.

Measurements of photon and jet production properties with ATLAS

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00237016; The ATLAS collaboration

2016-09-09

Summary of recent ATLAS measurements of jet and photon production using proton–proton (pp) collisions from the Large Hadron Collider. The charged-particle multiplicity in jets, and jet charge measurements are presented using 8 TeV pp collisions. Differential measurements of jet and photon cross-sections are shown for 7, 8 and 13 TeV pp collisions.

Electrochemical noise measurements under pressurized water reactor conditions

International Nuclear Information System (INIS)

Van Nieuwenhove, R.

2000-01-01

Electrochemical potential noise measurements on sensitized stainless steel pressure tubes under pressurized water reactor (PWR) conditions were performed for the first time. Very short potential spikes, believed to be associated to crack initiation events, were detected when stressing the sample above the yield strength and increased in magnitude until the sample broke. Sudden increases of plastic deformation, as induced by an increased tube pressure, resulted in slower, high-amplitude potential transients, often accompanied by a reduction in noise level

Investigation of Seepage Meter Measurements in Steady Flow and Wave Conditions.

Science.gov (United States)

Russoniello, Christopher J; Michael, Holly A

2015-01-01

Water exchange between surface water and groundwater can modulate or generate ecologically important fluxes of solutes across the sediment-water interface. Seepage meters can directly measure fluid flux, but mechanical resistance and surface water dynamics may lead to inaccurate measurements. Tank experiments were conducted to determine effects of mechanical resistance on measurement efficiency and occurrence of directional asymmetry that could lead to erroneous net flux measurements. Seepage meter efficiency was high (average of 93%) and consistent for inflow and outflow under steady flow conditions. Wave effects on seepage meter measurements were investigated in a wave flume. Seepage meter net flux measurements averaged 0.08 cm/h-greater than the expected net-zero flux, but significantly less than theoretical wave-driven unidirectional discharge or recharge. Calculations of unidirectional flux from pressure measurements (Darcy flux) and theory matched well for a ratio of wave length to water depth less than 5, but not when this ratio was greater. Both were higher than seepage meter measurements of unidirectional flux made with one-way valves. Discharge averaged 23% greater than recharge in both seepage meter measurements and Darcy calculations of unidirectional flux. Removal of the collection bag reduced this net discharge. The presence of a seepage meter reduced the amplitude of pressure signals at the bed and resulted in a nearly uniform pressure distribution beneath the seepage meter. These results show that seepage meters may provide accurate measurements of both discharge and recharge under steady flow conditions and illustrate the potential measurement errors associated with dynamic wave environments. © 2014, National Ground Water Association.

Measurement of heat stress conditions at cow level and comparison to climate conditions at stationary locations inside a dairy barn.

Science.gov (United States)

Schüller, Laura K; Heuwieser, Wolfgang

2016-08-01

The objectives of this study were to examine heat stress conditions at cow level and to investigate the relationship to the climate conditions at 5 different stationary locations inside a dairy barn. In addition, we compared the climate conditions at cow level between primiparous and multiparous cows for a period of 1 week after regrouping. The temperature-humidity index (THI) differed significantly between all stationary loggers. The lowest THI was measured at the window logger in the experimental stall and the highest THI was measured at the central logger in the experimental stall. The THI at the mobile cow loggers was 2·33 THI points higher than at the stationary loggers. Furthermore, the mean daily THI was higher at the mobile cow loggers than at the stationary loggers on all experimental days. The THI in the experimental pen was 0·44 THI points lower when the experimental cow group was located inside the milking parlour. The THI measured at the mobile cow loggers was 1·63 THI points higher when the experimental cow group was located inside the milking parlour. However, there was no significant difference for all climate variables between primiparous and multiparous cows. These results indicate, there is a wide range of climate conditions inside a dairy barn and especially areas with a great distance to a fresh air supply have an increased risk for the occurrence of heat stress conditions. Furthermore, the heat stress conditions are even higher at cow level and cows not only influence their climatic environment, but also generate microclimates within different locations inside the barn. Therefore climate conditions should be obtained at cow level to evaluate the heat stress conditions that dairy cows are actually exposed to.

Effect of fermentation conditions on lipase production by Candida utilis

Directory of Open Access Journals (Sweden)

SANJA Z. GRBAVCIC

2007-08-01

Full Text Available A wild yeast strain isolated from spoiled soybean oil and identified as Candida utilis initially presented rather low lipase activity (approximately 4 IU dm-3 in submerged culture in a universal yeast medium containing 2 % malt extract. Stu­dies were undertaken to improve the lipase production. The best yields of lipase were obtained with a medium supplemented with caprylic and oleic acids as indu­cers, but higher concentrations of the former (> 0.5 % had a negative effect on the lipase production and cell growth. The type of nitrogen source seemed also to be very important. The highest lipolytic activity of 284 IU dm-3 was achieved after 5 days of fermentation in a medium containing oleic acid and hydrolyzed casein as carbon and nitrogen sources, respectively, and supplemented with Tween 80®. It was shown that optimization of the fermentation conditions can lead to a significant improvement in the lipase production (more than 70-fold higher compared to the initial value obtained in the non-optimized medium.

Ordering Strategy for Fresh Agricultural Products in External Financing Condition

Institute of Scientific and Technical Information of China (English)

Wenyi; DU

2014-01-01

This paper firstly introduced the two stage supply chain consisting of single agricultural product producer and fund restraint retailer.Then,it analyzed the influence of bank interest rate on order quantity,wholesale price and expected profit of retailer and producer on the condition of retailer taking external loan strategy.Studies have shown that when the bank interest rate is in(0,0.9),the order quantity of agricultural products is a decreasing function of bank interest rate; when the bank interest rate is in(0,1),wholesale price of agricultural products decreases with increase in the bank interest rate; when the bank interest rate is in(0,0.6),the expected profit of retailer is a decreasing function of bank interest rate; when the bank interest rate is in(0,1),the expected profit of producer decreases with increase in the bank interest rate.Finally,through simulation calculation examples,it verified suitability of the conclusion,in the hope of providing reference and application value for management of supply chain.

Alkaline conditions stimulate the production of 1,3-propanediol in Lactobacillus panis PM1 through shifting metabolic pathways.

Science.gov (United States)

Grahame, Douglas A S; Kang, Tae Sun; Khan, Nurul H; Tanaka, Takuji

2013-07-01

A novel Lactobacillus panis PM1 isolate was found to be capable of converting glycerol to 1,3-propanediol (1,3-PDO), an increasingly valuable commodity chemical. In this study the effects of various process parameters, including glucose and glycerol concentrations, inoculum size, temperature, aeration, pH, and carbon source were examined to determine the optimal conditions for the production of 1,3-PDO using a culture method simulating late log to early stationary phases. Inoculum size did not influence the production of 1,3-PDO, and temperature variance showed similar 1,3-PDO production between 25 and 37 °C under the examined conditions. Glycerol concentration and pH played a primary role in the final concentration of 1,3-PDO. The highest production occurred at 150-250 mM glycerol when 50 mM glucose was available. Alkaline initial conditions (pH 9-10) stimulated the production of 1,3-PDO which concurrently occurred with increased acetic acid production. Under these conditions, 213.6 mM of 1,3-PDO were produced from 300 mM glycerol (conversion efficiency was 71 %). These observations indicated that the production of 1,3-PDO was associated with the shift of the metabolic end-product ethanol to acetic acid, and that this shift resulted in an excess concentration of NADH available for the processing of glycerol to 1,3-PDO.

Comparison of hydrogen-production capability of four different Enterobacteriaceae strains under growing and non-growing conditions

Energy Technology Data Exchange (ETDEWEB)

Seol, Eunhee; Kim, Seohyoung; Raj, S. Mohan; Park, Sunghoon [Department of Chemical and Biochemical Engineering, Pusan National University, Busan 609-735 (Korea)

2008-10-15

Non-growing cells can function as whole-cell biocatalysts for hydrogen (H{sub 2}) production, a process that has recently drawn much attention. In order to evaluate their potential as whole-cell biocatalysts, we compared the H{sub 2}-production capability of four Enterobacteriaceae strains (Citrobacter amalonaticus Y19, Escherichia coli K-12 MG1655, Escherichia coli DJT135, and Enterobacter aerogenes) under growing and non-growing conditions. We evaluated their H{sub 2}-production activity at varying temperatures (25-45 C) and pH conditions (6.0-8.0) using glucose or formate as the carbon source. Under growing conditions with 10 mM glucose as a substrate, E. aerogenes exhibited the highest H{sub 2}-production activity (17.0 {+-} 0.2 {mu}mol H{sub 2} mg cell{sup -1} h{sup -1}) among the four strains, but the final H{sub 2} yield was similar (1.7-1.8 mol H{sub 2} mol{sup -1} glucose) in all four strains. H{sub 2} production in the four strains proceeded through a formate-dependent pathway that involved the formate hydrogen lyase (FHL) complex. Under non-growing conditions with 20 mM formate as a substrate, we obtained high H{sub 2}-production activities, in the range of 95.5-195.2 {mu}mol H{sub 2} mg cell{sup -1} h{sup -1}, with E. coli DJT135 exhibiting the highest activity (195.2 {mu}mol H{sub 2} mg{sup -1} h{sup -1}) at pH 6.0 and 45 C. In contrast, using glucose as the carbon substrate in non-growing cell experiments greatly reduced the H{sub 2}-production activity to 6.1-7.7 {mu}mol H{sub 2} mg cell{sup -1} h{sup -1}. This study indicated that formate is a better substrate than glucose for H{sub 2} production by non-growing cells, and that the H{sub 2}-production performance among the strains did not vary significantly, with the exception of E. coli K-12 MG1655. (author)

Productivity Measurement in Manufacturing and the Expenditure Approach

DEFF Research Database (Denmark)

Schjerning, Bertel; Sørensen, Anders

2008-01-01

This paper studies conversion factors based on the expenditure approach and evaluates the appropriateness for international comparisons of output levels in manufacturing. We apply a consistency check based on the insight that relative productivity levels should be invariant to the choice of base....... The conclusion is insensitive to the applied method for developing conversion factors. The implication is that we cannot measure relative productivity levels in manufacturing across countries using the expenditure approach....

Productivity in Pediatric Palliative Care: Measuring and Monitoring an Elusive Metric.

Science.gov (United States)

Kaye, Erica C; Abramson, Zachary R; Snaman, Jennifer M; Friebert, Sarah E; Baker, Justin N

2017-05-01

Workforce productivity is poorly defined in health care. Particularly in the field of pediatric palliative care (PPC), the absence of consensus metrics impedes aggregation and analysis of data to track workforce efficiency and effectiveness. Lack of uniformly measured data also compromises the development of innovative strategies to improve productivity and hinders investigation of the link between productivity and quality of care, which are interrelated but not interchangeable. To review the literature regarding the definition and measurement of productivity in PPC; to identify barriers to productivity within traditional PPC models; and to recommend novel metrics to study productivity as a component of quality care in PPC. PubMed ® and Cochrane Database of Systematic Reviews searches for scholarly literature were performed using key words (pediatric palliative care, palliative care, team, workforce, workflow, productivity, algorithm, quality care, quality improvement, quality metric, inpatient, hospital, consultation, model) for articles published between 2000 and 2016. Organizational searches of Center to Advance Palliative Care, National Hospice and Palliative Care Organization, National Association for Home Care & Hospice, American Academy of Hospice and Palliative Medicine, Hospice and Palliative Nurses Association, National Quality Forum, and National Consensus Project for Quality Palliative Care were also performed. Additional semistructured interviews were conducted with directors from seven prominent PPC programs across the U.S. to review standard operating procedures for PPC team workflow and productivity. Little consensus exists in the PPC field regarding optimal ways to define, measure, and analyze provider and program productivity. Barriers to accurate monitoring of productivity include difficulties with identification, measurement, and interpretation of metrics applicable to an interdisciplinary care paradigm. In the context of inefficiencies

Corrosion-product transport, oxidation state and remedial measures

International Nuclear Information System (INIS)

Sawicki, J.A.; Brett, M.E.; Tapping, R.L.

1998-10-01

The issues associated with monitoring and controlling corrosion-product transport (CPT) in the balance-of-plant (BOP) and steam generators (SG) of CANDU stations are briefly reviewed. Efforts are focused on minimizing corrosion of carbon steel, which is used extensively in the CANDU primary and secondary systems. Emphasis is placed on the corrosion-product oxidation state as a monitor of water chemistry effectiveness and as a monitor of system corrosion effects. The discussion is based mostly on the results of observations from Ontario Hydro plants, and their comparisons with pressurized-water reactors. The effects of low oxygen and elevated hydrazine chemistry are reviewed, as well as the effects of layup and various startup conditions. Progress in monitoring electrochemical potential (ECP) at Ontario Hydro plants and its relationship to the oxidation state of corrosion products is reviewed. Observations on CPT on the primary side of SGs are also discussed. (author)

Techniques of treatment or conditioning for waste arising from 131I production

International Nuclear Information System (INIS)

Dellamono, J.C.

1989-07-01

Distillation, evaporation/crystallization, direct immobilization and some chemical like precipitation and reduction were studied as techniques of treatment or conditioning for waste arising from 131 I production. The description of all techniques studied, as well as evaluation and discussion of the results are presented. (author) [pt

Measurement of Survival Time in Brachionus Rotifers: Synchronization of Maternal Conditions.

Science.gov (United States)

Kaneko, Gen; Yoshinaga, Tatsuki; Gribble, Kristin E; Welch, David M; Ushio, Hideki

2016-07-22

Rotifers are microscopic cosmopolitan zooplankton used as models in ecotoxicological and aging studies due to their several advantages such as short lifespan, ease of culture, and parthenogenesis that enables clonal culture. However, caution is required when measuring their survival time as it is affected by maternal age and maternal feeding conditions. Here we provide a protocol for powerful and reproducible measurement of the survival time in Brachionus rotifers following a careful synchronization of culture conditions over several generations. Empirically, poor synchronization results in early mortality and a gradual decrease in survival rate, thus resulting in weak statistical power. Indeed, under such conditions, calorie restriction (CR) failed to significantly extend the lifespan of B. plicatilis although CR-induced longevity has been demonstrated with well-synchronized rotifer samples in past and present studies. This protocol is probably useful for other invertebrate models, including the fruitfly Drosophila melanogaster and the nematode Caenorhabditis elegans, because maternal age effects have also been reported in these species.

Production bias: A proposed modification of the driving force for void swelling under cascade damage conditions

International Nuclear Information System (INIS)

Woo, C.H.; Garner, F.A.

1991-11-01

A new concept of point-defect production as the main driving force for void swelling under cascade damage conditions is proposed. This concept takes into account the recombination and formation of immobile clusters and loops of vacancies and interstitials in the cascade region. The life times of the clusters and loops due to desolution are strong functions of the temperature, as well as their vacancy and interstitial nature. The resulting biased production of free point defects from the internal sources is shown to be a strong driving force for void swelling. The characteristics of void swelling due to production bias are described and compared with experimental results. We conclude that the production bias concept provides a good description of void swelling under cascade damage conditions

Production bias: A proposed modification of the driving force for void swelling under cascade damage conditions

International Nuclear Information System (INIS)

Woo, C.H.; Singh, B.N.; Garner, F.A.

1992-01-01

A new concept of point defect production as the main driving force for void swelling under cascade damage conditions is proposed. This concept takes into account the recombination and formation of immobile clusters and loops of vacancies and interstitials in the cascade region. The lifetimes of the clusters and loops due to desolution are strong functions of the temperature, as well as their vacancy and interstitial nature. The resulting biased production of free point defects from the internal sources is shown to be a strong driving force for void swelling. The characteristics of void swelling due to production bias are described and compared with experimental results. We conclude that the production bias concept provides a good description of void swelling under cascade damage conditions. (orig.)

Single top-quark production cross section measurements using the ATLAS detector at the LHC

CERN Document Server

Rieck, Patrick; The ATLAS collaboration

2016-01-01

Measurements of single top­quark production in proton proton collisions are presented. The measurements include the first such measurements from the 13 TeV ATLAS dataset. In the leading order process, a W boson is exchanged in the t­channel. The single top­quark and anti­top total production cross sections, their ratio, as well as a measurement of the inclusive production cross section is presented. At 8 TeV, differential cross­section measurements of the t­channel process are also presented, these measurements include limits on anomalous contributions to the Wtb vertex. A measurement of the production cross section of a single top quark in association with a W boson, the second largest single­top production mode, is also presented. Finally, evidence for single­top production in the 8 TeV ATLAS dataset is presented. All measurements are compared to state­of­ the­art theoretical calculations.

Do dose area product meter measurements reflect radiation doses ...

African Journals Online (AJOL)

Enrique

SA JOURNAL OF RADIOLOGY • August 2004. Abstract. This study determined the correlation between radiation doses absorbed by health care workers and dose area product meter (DAP) measurements at Universitas Hospital, Bloemfontein. The DAP is an instrument which accurately measures the radiation emitted from ...

Do dose area product meter measurements reflect radiation doses ...

African Journals Online (AJOL)

This study determined the correlation between radiation doses absorbed by health care workers and dose area product meter (DAP) measurements at Universitas Hospital, Bloemfontein. The DAP is an instrument which accurately measures the radiation emitted from the source. The study included the interventional ...

Experimental measurement of compressibility coefficients of synthetic sandstone in hydrostatic conditions

International Nuclear Information System (INIS)

Asaei, H; Moosavi, M

2013-01-01

For the characterization of the mechanical behavior of porous media in elastic conditions, the theory of poroelasticity is used. The number of poroelastic coefficients is greater in elastic conditions because of the complexity of porous media. The laboratory measurement of poroelastic coefficients needs a system that can control and measure the variables of poroelasticity. In this paper, experimental measurements of these coefficients are presented. Laboratory tests are performed using a system designed by the authors. Laboratory hydrostatic tests are performed on cylindrical samples in drained, pore pressure loading, undrained and dry conditions. Compressibilities (bulk and pore compressibility), effective stress and Skempton coefficients are measured by these tests. Samples are made of a composition (sand and cement) and are made by a compaction process synthetically. Calibration tests are performed for the setup to identify possible errors in the system and to correct the results of the main tests. This is done by performing similar compressibility tests at each stress level on a cylindrical steel sample (5.47 mm in diameter) with a longitudinal hole along it (hollow cylinder). A steel sample is used to assume an incompressible sample. The results of the tests are compared with the theory of poroelasticity and the obtained graphs and their errors are analyzed. This study shows that the results of the drained and pore pressure loading tests are compatible with poroelastic formulation, while the undrained results have errors because of extra fluid volume in the pore pressure system and calibration difficulties. (paper)

A computer controlled ultrasonic measurement and testequipment for rotation-symmetrical products

International Nuclear Information System (INIS)

Abend, K.; Lang, R.; Schmidt, U.; Schuett, U.; Sterberg, W.

1976-01-01

During production of rotation-symmetrical thin wall precision tubes, dimensions must be measured and the tubes have to be inspected for surface defects. Within the production area of the tubes, several measurement points for different applications are located at different places. The paper describes their on-line connection to a process-computer system

Evaluation of Water Quality Conditions Near Proposed Fish Production Sites Associated with the Yakima Fisheries Project, 1991-1993 Final Report.

Energy Technology Data Exchange (ETDEWEB)

Dauble, Dennis D.

1994-05-01

In 1991, the Pacific Northwest Laboratory (PNL) began studying water quality at several sites in the Yakima River Basin for the Bonneville Power Administration. These sites were being proposed as locations for fish culture facilities as part of the Yakima Fisheries Project (YFP). Surface water quality parameters near the proposed fish culture facilities are currently suitable for fish production. Water quality conditions in the mainstream Yakima River and its tributaries are generally excellent in the upper part of the watershed (i.e., near Cle Elum), but they are only fair to poor for the river downstream of Union Gap (river mile 107). Water quality of the Naches River near Oak Flats is also suitable for fish production. Groundwater supplies near the proposed fish production facilities typically have elevated concentrations of metals and dissolved gases. These conditions can be mitigated using best engineering practices such as precipitation and degasification. Additionally, mixing with surface water may improve these conditions. Depending on the location and depth of the well, groundwater temperatures may be warmer than optimum for acclimating and holding juvenile and adult fish. Water quality parameters measured in the Yakima River and tributaries sometimes exceed the range of values described as acceptable for culture of salmonids and for the protection of other aquatic life. However, constituent concentrations are within ranges that exist in many northwest fish hatcheries. Additionally, site-specific tests conducted by PNL (i.e., live box exposures and egg incubation studies) indicate that fish can be successfully reared in surface and well water near the proposed facility sites. Thus, there appear to be no constraints to artificial production for the YFP.

Production of radioactive sodium under working conditions for investigation into petroleum boreholes

International Nuclear Information System (INIS)

Kostin, Yu.I.; Gulin, Yu.A.; Sokolov, Yu.I.; Zhuvagin, I.G.

1976-01-01

Because it is advisable to use short-lived isotopes in monitoring the condition of boreholes, procedures are proposed for preparing 0.1-0.5 mC of Na 24 (half-life is 14.9 hr.) during a cycle under production conditions. It is recommended that baking soda should be used as activation material and an ampule polonium and beryllium neutron source with an activity of about 15 to 20 mC should be used as a source. Each operation uses 80 kg of baking soda and the activation lasts 30 to 50 hr

Effect of production conditions on the stability of a human bifidobacterial species Bifidobacterium longum in yogurt.

Science.gov (United States)

Abe, F; Tomita, S; Yaeshima, T; Iwatsuki, K

2009-12-01

Human bifidobacteria are more sensitive to external environmental factors than animal bifidobacteria, and it is difficult to ensure their stable survival in yogurt. The purpose of this investigation was to observe the survival of human bifidobacteria in yogurts produced under various production conditions. Frozen or lyophilized bifidobacteria starters containing Bifidobacterium longum BB536 originally isolated from an infant, and commercial lyophilized yogurt starters were used for yogurt preparation. After producing yogurts under various conditions, the survival of bifidobacteria in these yogurts over various storage periods was observed. Although there were some differences in bifidobacterial survival in yogurt between various production conditions, more than 1.0 x 10(7) CFU g(-1) of Bif. longum survived in yogurt after 35 days' storage at 5 degrees C. Lower fermentation temperature (37 degrees C) and inclusion of Lactococcus lactis in the starter significantly (P yogurt. In this investigation, the human bifidobacterial strain Bif. longum survived adequately in yogurt, although the fermentation temperature and starter composition affect bifidobacterial survival. This investigation indicates that stable probiotic yogurt using human bifidobacteria can be produced by choosing optimal production conditions.

Measurement of photon production cross sections with the ATLAS detector

CERN Document Server

Turra, Ruggero; The ATLAS collaboration

2017-01-01

The production of prompt isolated photons at hadron colliders provides a stringent test of perturbative QCD and can be used to probe the proton structure. The ATLAS Collaboration has performed precise measurements of the inclusive production of isolated prompt photons at a centre-of-mass energy of 13 TeV, differential in both rapidity and photon transverse momentum. In addition, the integrated and differential cross sections for isolated photon pairs at 8 TeV have been measured. The results are compared with state-of-the-art theory predictions at NLO in QCD and with predictions of several MC generators. The production of prompt photons in association with jets provides an additional testing ground for perturbative QCD (pQCD) with a hard colourless probe less affected by hadronisation effects than jet production. The dynamics of isolated-photon plus jet production in pp collisions at a centre-of-mass energy of 8 and 13 TeV will be presented and discussed.

Biomass and cellulosic ethanol production of forage sorghum under limited water conditions

Science.gov (United States)

A two year field study was conducted to evaluate biofuel production potential of two forage sorghum cultivars differing in brown midrib trait under non-irrigated and deficit irrigation conditions in the semiarid Southern High Plains of the U.S. Cultivar SP1990 (non-bmr = conventional cell wall comp...

Heterologous production of Pseudomonas aeruginosa rhamnolipid under anaerobic conditions for microbial enhanced oil recovery.

Science.gov (United States)

Zhao, F; Shi, R; Zhao, J; Li, G; Bai, X; Han, S; Zhang, Y

2015-02-01

The ex situ application of rhamnolipid to enhance oil recovery is costly and complex in terms of rhamnolipid production and transportation, while in situ production of rhamnolipid is restricted by the oxygen-deficient environments of oil reservoirs. To overcome the oxygen-limiting conditions and to circumvent the complex regulation of rhamnolipid biosynthesis in Pseudomonas aeruginosa, an engineered strain Pseudomonas stutzeri Rhl was constructed for heterologous production of rhamnolipid under anaerobic conditions. The rhlABRI genes for rhamnolipid biosynthesis were cloned into a facultative anaerobic strain Ps. stutzeri DQ1 to construct the engineered strain Rhl. Anaerobic production of rhamnolipid was confirmed by thin layer chromatography and Fourier transform infrared analysis. Rhamnolipid product reduced the air-water surface tension to 30.3 mN m(-1) and the oil-water interfacial tension to 0.169 mN m(-1). Rhl produced rhamnolipid of 1.61 g l(-1) using glycerol as the carbon source. Rhl anaerobic culture emulsified crude oil up to EI24 ≈ 74. An extra 9.8% of original crude oil was displaced by Rhl in the core flooding test. Strain Rhl achieved anaerobic production of rhamnolipid and worked well for enhanced oil recovery in the core flooding model. The rhamnolipid produced by Rhl was similar to that of the donor strain SQ6. This is the first study to achieve anaerobic and heterologous production of rhamnolipid. Results demonstrated the potential feasibility of Rhl as a promising strain to enhance oil recovery through anaerobic production of rhamnolipid. © 2014 The Society for Applied Microbiology.

Nitrous oxide production during nitrification from organic solid waste under temperature and oxygen conditions.

Science.gov (United States)

Nag, Mitali; Shimaoka, Takayuki; Komiya, Teppei

2016-11-01

Landfill aeration can accelerate the biological degradation of organic waste and reduce methane production; however, it induces nitrous oxide (N2O), a potent greenhouse gas. Nitrification is one of the pathways of N2O generation as a by-product during aerobic condition. This study was initiated to demonstrate the features of N2O production rate from organic solid waste during nitrification under three different temperatures (20°C, 30°C, and 40°C) and three oxygen concentrations (5%, 10%, and 20%) with high moisture content and high substrates' concentration. The experiment was carried out by batch experiment using Erlenmeyer flasks incubated in a shaking water bath for 72 h. A duplicate experiment was carried out in parallel, with addition of 100 Pa of acetylene as a nitrification inhibitor, to investigate nitrifiers' contribution to N2O production. The production rate of N2O ranged between 0.40 × 10(-3) and 1.14 × 10(-3) mg N/g-DM/h under the experimental conditions of this study. The rate of N2O production at 40°C was higher than at 20°C and 30°C. Nitrification was found to be the dominant pathway of N2O production. It was evaluated that optimization of O2 content is one of the crucial parameters in N2O production that may help to minimize greenhouse gas emissions and N turnover during aeration.

Hydrogen production by Chlamydomonas reinhardtii under light driven sulfur deprived condition

Energy Technology Data Exchange (ETDEWEB)

Vijayaraghavan, Krishnan; Karthik, Rajendran [Biotechnology Research Division, Department of Biotechnology, Prathyusha Institute of Technology and Management, Aranvoyalkuppam, Thiruvallur District 602025, Tamil Nadu (India); Kamala Nalini, S.P. [Department of Biotechnology, Vel Group of Educational Institutions, Avadi, Alamadhi Road, Chennai 600062, Tamil Nadu (India)

2009-10-15

This article explores the possibility of demonstrating sustainable photohydrogen production using Chlamydomonas reinhardtii when grown in sulfur deprived photoautotrophic condition. The hydrogen evolving capability of the algal species was monitored based on alternating light and dark period. Investigation was carried out during the day time in order to exploit the solar energy for meeting the demand of the light period. The results showed that when the reactor was operated at varying photoperiod namely 2, 3 and 4 h of alternating light and dark period, the gas generation was found to be 32 {+-} 4, 63 {+-} 7 and 52 {+-} 5 mL/h, while the corresponding hydrogen content was 47, 86 and 87% respectively. Functional components of hydrogen generation reaction centers were also analyzed, which showed that the PS(I) reaction centers were involved in hydrogen production pathway, as the light absorption by PS(I) was prerequisite for hydrogen generation under sulfur deprived photoautotrophic condition. The findings showed a higher gas yield and hydrogen content under dark period, whereas under light period the gas content was below detectable level for hydrogen due to the reversible hydrogenase reaction. (author)

Evaluation and prioritization of rice production practices and constraints under temperate climatic conditions using Fuzzy Analytical Hierarchy Process (FAHP)

International Nuclear Information System (INIS)

Mir, S.A.; Padma, T.

2016-01-01

Due to overwhelming complex and vague nature of interactions between multiple factors describing agriculture, Multi-Criteria Decision Making (MCDM) methods are widely used from farm to fork to facilitate systematic and transparent decision support, figure out multiple decision outcomes and equip decision maker with confident decision choices in order to choose best alternative. This research proposes a Fuzzy Analytical Hierarchy Process (FAHP) based decision support to evaluate and prioritize important factors of rice production practices and constraints under temperate climatic conditions and provides estimate of weightings, which measure relative importance of critical factors of the crop under biotic, abiotic, socio-economic and technological settings. The results envisage that flood, drought, water logging, late sali, temperature and rainfall are important constraints. However, regulating transplantation time; maintaining planting density; providing training to the educated farmers; introducing high productive varieties like Shalimar Rice-1 and Jhelum; better management of nutrients, weeds and diseases are most important opportunities to enhance rice production in the region. Therefore, the proposed system supplements farmers with precise decision information about important rice production practices, opportunities and constraints.

Evaluation and prioritization of rice production practices and constraints under temperate climatic conditions using Fuzzy Analytical Hierarchy Process (FAHP

Directory of Open Access Journals (Sweden)

Shabir A. Mir

2016-12-01

Full Text Available Due to overwhelming complex and vague nature of interactions between multiple factors describing agriculture, Multi-Criteria Decision Making (MCDM methods are widely used from farm to fork to facilitate systematic and transparent decision support, figure out multiple decision outcomes and equip decision maker with confident decision choices in order to choose best alternative. This research proposes a Fuzzy Analytical Hierarchy Process (FAHP based decision support to evaluate and prioritize important factors of rice production practices and constraints under temperate climatic conditions and provides estimate of weightings, which measure relative importance of critical factors of the crop under biotic, abiotic, socio-economic and technological settings. The results envisage that flood, drought, water logging, late sali, temperature and rainfall are important constraints. However, regulating transplantation time; maintaining planting density; providing training to the educated farmers; introducing high productive varieties like Shalimar Rice-1 and Jhelum; better management of nutrients, weeds and diseases are most important opportunities to enhance rice production in the region. Therefore, the proposed system supplements farmers with precise decision information about important rice production practices, opportunities and constraints.

Evaluation and prioritization of rice production practices and constraints under temperate climatic conditions using Fuzzy Analytical Hierarchy Process (FAHP)

Energy Technology Data Exchange (ETDEWEB)

Mir, S.A.; Padma, T.

2016-07-01

Due to overwhelming complex and vague nature of interactions between multiple factors describing agriculture, Multi-Criteria Decision Making (MCDM) methods are widely used from farm to fork to facilitate systematic and transparent decision support, figure out multiple decision outcomes and equip decision maker with confident decision choices in order to choose best alternative. This research proposes a Fuzzy Analytical Hierarchy Process (FAHP) based decision support to evaluate and prioritize important factors of rice production practices and constraints under temperate climatic conditions and provides estimate of weightings, which measure relative importance of critical factors of the crop under biotic, abiotic, socio-economic and technological settings. The results envisage that flood, drought, water logging, late sali, temperature and rainfall are important constraints. However, regulating transplantation time; maintaining planting density; providing training to the educated farmers; introducing high productive varieties like Shalimar Rice-1 and Jhelum; better management of nutrients, weeds and diseases are most important opportunities to enhance rice production in the region. Therefore, the proposed system supplements farmers with precise decision information about important rice production practices, opportunities and constraints.

Measurement framework for product service system performance of generator set distributors

Science.gov (United States)

Sofianti, Tanika D.

2017-11-01

Selling Generator Set (Genset) in B2B market, distributors assisted manufacturers to sell products. This is caused by the limited resources owned by the manufacturer for adding service elements. These service elements are needed to enhance the competitiveness of the generator sets. Some genset distributors often sell products together with supports to their customers. Industrial distributor develops services to meet the needs of the customer. Generator set distributors support machines and equipment produced by manufacturer. The services delivered by the distributors could enhance value obtained by the customers from the equipment. Services provided to customers in bidding process, ordering process of the equipment from the manufacturer, equipment delivery, installations, and the after sales stage. This paper promotes framework to measure Product Service System (PSS) of Generator Set distributors in delivering their products and services for the customers. The methodology of conducting this research is by adopting the perspective of the providers and customers and by taking into account the tangible and intangible products. This research leads to the idea of improvement of current Product Service System of a Genset distributor. This research needs further studies in more detailed measures and the implementation of measurement tools.

Consolidated bioprocessing strategy for ethanol production from Jerusalem artichoke tubers by Kluyveromyces marxianus under high gravity conditions.

Science.gov (United States)

Yuan, W J; Chang, B L; Ren, J G; Liu, J P; Bai, F W; Li, Y Y

2012-01-01

Developing an innovative process for ethanol fermentation from Jerusalem artichoke tubers under very high gravity (VHG) conditions. A consolidated bioprocessing (CBP) strategy that integrated inulinase production, saccharification of inulin contained in Jerusalem artichoke tubers and ethanol production from sugars released from inulin by the enzyme was developed with the inulinase-producing yeast Kluyveromyces marxianus Y179 and fed-batch operation. The impact of inoculum age, aeration, the supplementation of pectinase and nutrients on the ethanol fermentation performance of the CBP system was studied. Although inulinase activities increased with the extension of the seed incubation time, its contribution to ethanol production was negligible because vigorously growing yeast cells harvested earlier carried out ethanol fermentation more efficiently. Thus, the overnight incubation that has been practised in ethanol production from starch-based feedstocks is recommended. Aeration facilitated the fermentation process, but compromised ethanol yield because of the negative Crabtree effect of the species, and increases the risk of contamination under industrial conditions. Therefore, nonaeration conditions are preferred for the CBP system. Pectinase supplementation reduced viscosity of the fermentation broth and improved ethanol production performance, particularly under high gravity conditions, but the enzyme cost should be carefully balanced. Medium optimization was performed, and ethanol concentration as high as 94·2 g l(-1) was achieved when 0·15 g l(-1) K(2) HPO(4) was supplemented, which presents a significant progress in ethanol production from Jerusalem artichoke tubers. A CBP system using K. marxianus is suitable for efficient ethanol production from Jerusalem artichoke tubers under VHG conditions. Jerusalem artichoke tubers are an alternative to grain-based feedstocks for ethanol production. The high ethanol concentration achieved using K. marxianus with the

The Validation of the GEWEX SRB Surface Shortwave Flux Data Products Using BSRN Measurements: A Systematic Quality Control, Production and Application Approach

Science.gov (United States)

Zhang, Taiping; Stackhouse, Paul W., Jr.; Gupta, Shashi K.; Cox, Stephen J.; Mikovitz, J. Colleen; Hinkelman, Laura M.

2013-01-01

The NASA/GEWEX Surface Radiation Budget (SRB) project has produced a 24.5-year continuous record of global shortwave and longwave radiation fluxes at TOA and the Earth's surface from satellite measurements. The time span of the data is from July 1983 to December 2007, and the spatial resolution is 11 latitude11 longitude. The inputs of the latest version (Release 3.0) include the GEOS Version 4.0.3 meteorological information and cloud properties derived from ISCCP DX data. The SRB products are available on 3-hourly, 3-hourly-monthly, daily and monthly time scales. To assess the quality of the product, we extensively validated the SRB data against 5969 site-months of groundbased measurements from 52 Baseline Surface Radiation Network (BSRN) stations. This paper describes first the characteristics of the BSRN data and the GEWEX SRB data, the methodology for quality control and processing of the shortwave BSRN data, and then the systematic SRB-BSRN comparisons. It is found that, except for occasional extreme outliers as seen in scatter plots, the satellite-based surface radiation data generally agree very well with BSRN measurements. Specifically, the bias/RMS for the daily and monthly mean shortwave fluxes are, respectively, -3.6/35.5 and -5.2/23.3W1 m2 under all-sky conditions.

Measuring a Country's Product Ladder and Technology Level based on Trade Flow

Directory of Open Access Journals (Sweden)

Jong-il Kim

2006-06-01

Full Text Available This study tries to quantify the technology level of products based on the concept of product ladder. While many studies on country technology competitiveness use the aggregate indices such as total factor productivity and revealed comparative advantage, this study estimates the ranking of about 2000 products in product ladder by using SITC 5 digit level export data. Based on the product ladder, this study measures the country and industry ranking and explores the characteristics of the ranking. It provides the international comparison of inter-industry and intra-industry ranking differences in product ladder. The statistical relationships between the ranking in product ladder and the determinants of technology level such as R&D and physical capital investment and wage, confirms that the measured ranking in product ladder could be regarded as an indirect indicator of technology level. The product ladder is applied to the estimation of production function to see the effect of the product differentiation on labor productivity.

HbA2 measurements in β-thalassemia and in other conditions

Directory of Open Access Journals (Sweden)

Giovanni Ivaldi

2014-09-01

Full Text Available Quite a few papers have been written on the significance of elevated hemoglobin (Hb A2 as a parameter for the diagnosis of β-thalassemia trait, on the cutoff values to be used in diagnostics and on the significance and effects of factors reducing or elevating the expression of HbA2 and last but not least on the need for reliable measurement methods and precise calibrations with accurate standards. However, little has been published on the causes that elevate or reduce the HbA2 levels in β- and a-thalassemia and in other conditions. For a better understanding of the value of a precise measurement of this parameter we summarize and elucidate in this review the direct and indirect mechanisms that cause the variations in HbA2 expression and that influence the value of this parameter in particular conditions. We conclude by explaining the advantages and disadvantages of trusting on a precise measurement in the complete diagnostic contest.

Hospitals Productivity Measurement Using Data Envelopment Analysis Technique.

Science.gov (United States)

Torabipour, Amin; Najarzadeh, Maryam; Arab, Mohammad; Farzianpour, Freshteh; Ghasemzadeh, Roya

2014-11-01

This study aimed to measure the hospital productivity using data envelopment analysis (DEA) technique and Malmquist indices. This is a cross sectional study in which the panel data were used in a 4 year period from 2007 to 2010. The research was implemented in 12 teaching and non-teaching hospitals of Ahvaz County. Data envelopment analysis technique and the Malmquist indices with an input-orientation approach, was used to analyze the data and estimation of productivity. Data were analyzed using the SPSS.18 and DEAP.2 software. Six hospitals (50%) had a value lower than 1, which represents an increase in total productivity and other hospitals were non-productive. the average of total productivity factor (TPF) was 1.024 for all hospitals, which represents a decrease in efficiency by 2.4% from 2007 to 2010. The average technical, technologic, scale and managerial efficiency change was 0.989, 1.008, 1.028, and 0.996 respectively. There was not a significant difference in mean productivity changes among teaching and non-teaching hospitals (P>0.05) (except in 2009 years). Productivity rate of hospitals had an increasing trend generally. However, the total average of productivity was decreased in hospitals. Besides, between the several components of total productivity, variation of technological efficiency had the highest impact on reduce of total average of productivity.

Validation and Recommendation of Methods to Measure Biogas Production Potential of Animal Manure

Directory of Open Access Journals (Sweden)

C. H. Pham

2013-06-01

Full Text Available In developing countries, biogas energy production is seen as a technology that can provide clean energy in poor regions and reduce pollution caused by animal manure. Laboratories in these countries have little access to advanced gas measuring equipment, which may limit research aimed at improving local adapted biogas production. They may also be unable to produce valid estimates of an international standard that can be used for articles published in international peer-reviewed science journals. This study tested and validated methods for measuring total biogas and methane (CH4 production using batch fermentation and for characterizing the biomass. The biochemical methane potential (BMP (CH4 NL kg−1 VS of pig manure, cow manure and cellulose determined with the Moller and VDI methods was not significantly different in this test (p>0.05. The biodegradability using a ratio of BMP and theoretical BMP (TBMP was slightly higher using the Hansen method, but differences were not significant. Degradation rate assessed by methane formation rate showed wide variation within the batch method tested. The first-order kinetics constant k for the cumulative methane production curve was highest when two animal manures were fermented using the VDI 4630 method, indicating that this method was able to reach steady conditions in a shorter time, reducing fermentation duration. In precision tests, the repeatability of the relative standard deviation (RSDr for all batch methods was very low (4.8 to 8.1%, while the reproducibility of the relative standard deviation (RSDR varied widely, from 7.3 to 19.8%. In determination of biomethane concentration, the values obtained using the liquid replacement method (LRM were comparable to those obtained using gas chromatography (GC. This indicates that the LRM method could be used to determine biomethane concentration in biogas in laboratories with limited access to GC.

Operating conditions of T.B.P. line uranium purification plant, for uranium dioxide production

International Nuclear Information System (INIS)

Vardich, R.N.; La Gamma, A.M.; Anasco, R.; Soler, S.M.G. de; Isnardi, E.; Gea, V.; Chiaraviglio, R.; Matyjasczyk, E.; Aramayo, R.

1992-01-01

In this contribution are presented the operative conditions and the results obtained step of the Uranium dioxide production plant of Argentina. The refining step involve the Uranium concentrate dissolution, the silica ageing, the filtration and liquid - liquid extraction with n-tributyl phosphate solution in kerosene. The established operative conditions allow to obtain Uranyl nitrate solutions of nuclear purity in industrial scale. (author)

Biodiesel production process optimization and characterization to assess the suitability of the product for varied environmental conditions

Energy Technology Data Exchange (ETDEWEB)

Eevera, T.; Rajendran, K.; Saradha, S. [Department of Biotechnology, Periyar Maniammai University, Periyar Nagar, Vallam, Thanjavur, Tamilnadu 613 403 (India)

2009-03-15

In this study, both edible (coconut oil, palm oil, groundnut oil, and rice bran oil) and non-edible oils (pongamia, neem and cotton seed oil) were used to optimize the biodiesel production process variables like catalyst concentration, amount of methanol required for reaction, reaction time and reaction temperature. The fuel properties like specific gravity, moisture content, refractive index, acid value, iodine number, saponification value and peroxide value were estimated. Based on the cetane number and iodine value, the methyl esters obtained from palm and coconut oils were not suitable to use as biodiesel in cold weather conditions, but for hot climate condition biodiesel obtained from the remaining oil sources is suitable. (author)

Stability studies needed to define the handling and transport conditions of sensitive pharmaceutical or biotechnological products.

Science.gov (United States)

Ammann, Claude

2011-12-01

Many pharmaceutical or biotechnological products require transport using temperature-controlled systems to keep their therapeutic properties. There are presently no official guidelines for testing pharmaceutical products in order to define suitable transport specifications. After reviewing the current guidance documents, this paper proposes a methodology for testing pharmaceutical products and defining appropriate transport conditions.

Measurements of Drell-Yan and vector boson plus jet productions in ATLAS

CERN Document Server

Donadelli, Marisilvia; The ATLAS collaboration

2015-01-01

The inclusive production of W and Z bosons as well the off-shell Z/gamma* production at hadron colliders provide a benchmark of our understanding of quantum chromodynamic (QCD) and electroweak (EW) processes. The measurement of their production cross-sections can be compared to theory calculations at NNLO QCD and have an impact on our knowledge of the parton densities of the proton. The production of heavy flavour in association with a W or Z boson represent important backgrounds to Higgs and BSM studies and are challenging to calculate in QCD. During the LHC Run 1, several precision measurements were performed by the ATLAS experiment using pp data at 7 TeV of integrated as well as differential cross sections. Comparisons are made to a diverse set of state-­of­the­-art NLO QCD calculations, some of which are interfaced to MC generators for parton showering and hadronization. Z+bb production probes the b­-quark production by high-­order QCD processes. Measurement of W+c production cross section has a uniq...

Economic analysis of sunflower production in the view of orobanche resistance conditions

International Nuclear Information System (INIS)

Semerci, A.

2013-01-01

The objective of this research is to determine the use of production factors in 3 different types of sunflower production with respect to orobanche resistance in the agricultural enterprises in Thrace Region which is located at European continent of Turkey. The data used in this research have been obtained through questionnaire technique from 571 agricultural enterprises which were determined by Stratified Random Sampling Method in 2009. It has been reached to the highest yield by 189.30 kg da-1 and the highest gross profit by 37.91 US$ da-1 in the production of sunflower, resistant to orobanche. In the research, it has been determined that the rate of soil testing among the sunflower producers is considerably low and almost the whole of the production has been made under rainfed conditions. As a result of the research, it has been concluded that orobanche resistant sunflower, which has higher water productivity than other cultivars by 367.13 g m/sup 3/, will have a higher proportion in the sunflower cultivation areas in future because of its higher contribution to producer welfare. (author)

Fuel behaviour and fission product release under realistic hydrogen conditions comparisons between HEVA 06 test results and Vulcain computations

International Nuclear Information System (INIS)

Dumas, J.M.; Lhiaubet, G.

1989-07-01

The HEVA 06 test was designed to simulate the conditions existing at the time when fission products are released from irradiated fuel under hydrogen conditions occurring in a PWR core at low pressure. The test conditions were defined from results provided by the core degradation module of the ESCADRE system (1): VULCAIN. This computer code has been recently used to analyse the early core degradation of a 900 MWe PWR in the AF accident sequence (as defined in WASH - 1400, USNRC - 1975). In this scenario, the core would begin to uncover about one day after scram with the system pressure at about 0.4 MPa. The fission product release starts 70 minutes after core dewatering. The F.P. are transferred to the core outlet in an increasingly hydrogen-rich steam atmosphere. The carrier gas is nearly pure hydrogen in the time period 100 - 130 minutes after core uncovering. A large release of F.P. is predicted in the upper part of the core when the steam starvation occurs. At that time, two thirds of the cladding have been oxidised on an average. Before each HEVA test a fuel sample with a burn-up of 36 GWd/tU is reirradiated in order to observe the release of short-lived fission products. A pre-oxidation was primarely conducted in the HEVA 06 test at a temperature of 1300 0 C and controlled to reach a 2/3 cladding oxidation state. Then the steam was progressively replaced by hydrogen and a heat-up rate of 1.5 0 C/s was induced to reach a temperature of 2100 0 C. The fuel was maintained at this temperature for half an hour in hydrogen. The volatile F.P. release kinetics were observed by on-line gamma spectrometry. Pre test calculations of F.P. release kinetics performed with the EMIS module based on the CORSOR models (3) are compared with the test results. Measured releases of cesium and iodine are really lower than those predicted. Axial and radial F.P. distributions in the fuel pellets are available from gamma tomography measurements performed after the test. Tellurium seems

Importance and condition of forage crops seed production in agriculture of the Republic of Serbia

Directory of Open Access Journals (Sweden)

Đokić Dragoslav

2013-01-01

Full Text Available For contemporary and economical livestock production, especially cattle and sheep raising, it is necessary to achieve high production of livestock feed while reducing production costs. Improving the production of perennial grasses and legumes creates a good basis for the development of livestock production in different agro-ecological conditions of Serbia. It also establishes a link between farming and animal husbandry, which is of particular importance for the preservation and higher fertility of arable land and the protection of agro-ecosystems. An important factor for the cheaper production of livestock feed is the possibility to provide sufficient quantities of quality seeds at affordable prices. Production of quality seeds of local varieties of perennial legumes is possible to obtain sufficient amounts of good quality forage. Current situation in forage crop seed production of the Republic of Serbia is unsatisfactory because the seed of perennial grasses are mostly imported. Domestic production of alfalfa, red clover and birdsfoot trefoil met domestic needs only in some years. Seed of imported varieties are often not satisfactory because those varieties are not adapted to our local agro-ecological conditions. The present results provide the basis and direction for further researches that may provide solutions to increase seed yields and which will be widely accepted in practice, which will make the production more cost-effective. Institute for forage crops Kruševac is making a significant contribution to the development of technology of seed productions, especially alfalfa, red clover and perennial grasses. Therefore the role of the Institute is very important and necessary link between production, processing and trading seeds of perennial legumes and grasses in Serbia.

Biogas production from high-yielding energy crops in boreal conditions

Energy Technology Data Exchange (ETDEWEB)

Seppala, M.

2013-11-01

In this thesis, the methane production potential of traditional and novel energy crops was evaluated in boreal conditions. The highest methane yield per hectare was achieved with maize (4 000-9 200 m{sup 3}CH{sub 4} ha{sup -1} a{sup -1}) and the second highest with brown knapweed (2 700-6 100 m{sup 3}CH{sub 4} ha{sup -1} a{sup -1}). Recently, the most feasible energy crop, grass, produced 1 200-3 600 m{sup 3}CH{sub 4} ha{sup -1} a{sup -1}. The specific methane yields of traditional and novel energy crops varied from 170-500 l kg{sup -1} volatile solid (VS). The highest specific methane yields were obtained with maize, while the novel energy crops were at a lower range. The specific methane yields decreased in the later harvest time with maize and brown knapweed, and the specific methane yield of the grasses decreased from the 1st to 2nd harvests. Maize and brown knapweed produced the highest total solid (TS) yields per hectare 13-23 tTS ha{sup -1}, which were high when compared with the TS yields of grasses (6-13 tTS ha{sup -1}). The feasibility of maize and brown knapweed in co-digestion with liquid cow manure, in continuously stirred tank reactors (CSTR), was evaluated. According to the CSTR runs, maize and brown knapweed are suitable feeds and have stable processes, producing the highest methane yields (organic loading rate 2 kgVS m{sup -3}d{sup -1}), with maize at 259 l kgVS{sup -1} and brown knapweed at 254 l kgVS{sup -1}. The energy balance (input/output) of the cultivation of the grasses, maize and brown knapweed was calculated in boreal conditions, and it was better when the digestate was used as a fertilizer (1.8-4.8 %) than using chemical fertilizers (3.7-16.2 %), whose production is the most energy demanding process in cultivation. In conclusion, the methane production of maize, grasses and novel energy crops can produce high methane yields and are suitable feeds for anaerobic digestion. The cultivation managements of maize and novel energy crops for

External quality measurements reveal internal processes

NARCIS (Netherlands)

Schouten, R.E.; Costa, J.M.; Kooten, van O.

2003-01-01

With the present developments in CA technology it becomes possible to fine tune the storage conditions to the specific needs of the product. This generates the need to know the exact quality conditions of the product before storage starts. By measuring the initial quality we can determine these

Can ensemble condition in a hall be improved and measured?

DEFF Research Database (Denmark)

Gade, Anders Christian

1988-01-01

of the ceiling reflectors; and (c) changing the position of the orchestra on the platform. These variables were then tested in full scale experiments in the hall including subjective evaluation by the orchestra in order to verify their effects under practical conditions. New objective parameters, which showed......In collaboration with the Danish Broadcasting Corporation an extensive series of experiments has been carried out in The Danish Radio Concert Hall with the practical purpose of trying to improve the ensemble conditions on the platform for the resident symphony orchestra. First, a series...... very high correlations with the subjective data, also made it possible to compare the improvements with conditions as recently measured in famous European Halls. Besides providing the needed results, the experiments also shed some light on how musicians change their criteria for judging acoustic...

Profit and Risk Measures in Oil Production Optimization

DEFF Research Database (Denmark)

Capolei, Andrea; Foss, Bjarne; Jørgensen, John Bagterp

2015-01-01

In oil production optimization, we usually aim to maximize a deterministic scalar performance index such as the profit over the expected reservoir lifespan. However, when uncertainty in the parameters is considered, the profit results in a random variable that can assume a range of values dependi...... pro and cons for each of them. Finally, among the presented risk measures, we identify two of them as appropriate risk measures when minimizing the risk....

Modelling of Ethanol Production from Red Beet Juice by Saccharomyces cerevisiae under Thermal and Acid Stress Conditions

Directory of Open Access Journals (Sweden)

Donaji Jiménez-Islas

2014-01-01

Full Text Available In this work the effects of pH and temperature on ethanol production from red beet juice by the strains Saccharomyces cerevisiae ITD00196 and S. cerevisiae ATCC 9763 are studied. Logistic, Pirt, and Luedeking-Piret equations were used to describe quantitatively the microbial growth, substrate consumption, and ethanol production, respectively. The two S. cerevisiae strains used in this study were able to produce ethanol with high yield and volumetric productivity under acid and thermal stress conditions. The equations used to model the fermentation kinetics fit very well with the experimental data, thus establishing that ethanol production was growth associated under the evaluated conditions. The yeast S. cerevisiae ITD00196 had the best fermentative capacity and could be considered as an interesting option to develop bioprocesses for ethanol production.

Measuring production loss due to health and work environment problems: construct validity and implications.

Science.gov (United States)

Karlsson, Malin Lohela; Bergström, Gunnar; Björklund, Christina; Hagberg, Jan; Jensen, Irene

2013-12-01

The aim was to validate two measures of production loss, health-related and work environment-related production loss, concerning their associations with health status and work environment factors. Validity was assessed by evaluating the construct validity. Health problems related and work environment-related problems (or factors) were included in separate analyses and evaluated regarding the significant difference in proportion of explained variation (R) of production loss. health problems production loss was not found to fulfill the criteria for convergent validity in this study; however, the measure of work environment-related production loss did fulfill the criteria that were set up. The measure of work environment-related production loss can be used to screen for production loss due to work environment problems as well as an outcome measure when evaluating the effect of organizational interventions.

Effect of ultraviolet rays upon the productivity and adaptive possibilities of sows raised under industrial conditions

International Nuclear Information System (INIS)

Stefanova, S.; Benkov, M.; Panev, P.; Zlatev, D.

1983-01-01

Two experiments, aimed at establishing the effect of treatment with UV-rays on productivity of sows, the growth rate of pigs up to weaning, their adaptive reactions, and the micro-climate on the premises were carried out with 60 sows, divided into two groups: group i (controls) raised on premises without treatment with UV-rays, and group ii (experimental) raised on premises under treatment with UV-rays. Both nursing sows and piglets until their weaning were raised under industrial conditions. Type PRK-2 mercury lamp of 120 V, 3.75 A, and 375 W was used as a source of UV-rays. Each animal was exposed to irradiation daily for a period of 2 min. The live weight of sows, prolificacy, live weight of pigs at weaning and number of culled pigs during the sucking period, were checked. The adaptive reactions of sows and pigs were examined by ACT-hormon testing. Before treatment and 3 h after treatment with this hormone leucocyte, eosinophile and erythrocyte count and the haemoglobin, Ca, blood sugar, total protein, albumin and globulin in the blood were checked. The temperature, moisture, velocity of movement and gas composition of air were measured prior to blood sampling. Under the conditions existing in industrial pig-breeding complexes ensuring complete feeding of animals UV-treatment did not produce essential effects on the productivity of sows and the growth rate of pigs as well as on the adaptive reactions of animals and the micro-climate on the premises

Effect of ultraviolet rays upon the productivity and adaptive possibilities of sows raised under industrial conditions

Energy Technology Data Exchange (ETDEWEB)

Stefanova, S; Benkov, M; Panev, P; Zlatev, D [Pig-Breeding Research Institute, Shumen (Bulgaria)

1983-01-01

Two experiments, aimed at establishing the effect of treatment with UV-rays on productivity of sows, the growth rate of pigs up to weaning, their adaptive reactions, and the micro-climate on the premises were carried out with 60 sows, divided into two groups: group i (controls) raised on premises without treatment with UV-rays, and group ii (experimental) raised on premises under treatment with UV-rays. Both nursing sows and piglets until their weaning were raised under industrial conditions. Type PRK-2 mercury lamp of 120 V, 3.75 A, and 375 W was used as a source of UV-rays. Each animal was exposed to irradiation daily for a period of 2 min. The live weight of sows, prolificacy, live weight of pigs at weaning and number of culled pigs during the sucking period, were checked. The adaptive reactions of sows and pigs were examined by ACTH-hormone testing. Before treatment and 3 h after treatment with this hormone leucocyte, eosinophile and erythrocyte count and the hemoglobin, Ca, blood sugar, total protein, albumin and globulin in the blood were checked. The temperature, moisture, velocity of movement and gas composition of air were measured prior to blood sampling. Under the conditions existing in industrial pig-breeding complexes ensuring complete feeding of animals UV-treatment did not produce essential effects on the productivity of sows and the growth rate of pigs as well as on the adaptive reactions of animals and the micro-climate on the premises.

Analysis of the environmental conditions at Gale Crater from MSL/REMS measurements

Energy Technology Data Exchange (ETDEWEB)

Martinez, G.; Torre-Juarez, M. de la; Vicente-Retortillo, A.; Kemppinen, O.; Renno, N.; Lemmon, M.

2016-07-01

The environmental conditions at Gale Crater during the first 1160 sols of the Mars Science Laboratory (MSL) mission are assessed using measurements taken by the Rover Environmental Monitoring Station (REMS) on-board the MSL Curiosity rover. REMS is a suite of sensors developed to assess the environmental conditions along the rover traverse. In particular, REMS has been measuring atmospheric pressure, atmospheric and ground temperature, relative humidity, UV radiation flux and wind speed. Here we analyze processed data with the highest confidence possible of atmospheric pressure, atmospheric and ground temperature and relative humidity. In addition, we estimate the daily UV irradiation at the surface of Gale Crater using dust opacity values derived from the Mastcam instrument. REMS is still in operation, but it has already provided the most comprehensive coverage of surface environmental conditions recorded by a spacecraft landed on Mars. (Author)

Cultivating conditions effects on kefiran production by the mixed culture of lactic acid bacteria imbedded within kefir grains.

Science.gov (United States)

Zajšek, Katja; Goršek, Andreja; Kolar, Mitja

2013-08-15

The influence of fermentation temperature, agitation rate, and additions of carbon sources, nitrogen sources, vitamins and minerals on production of kefiran by kefir grains lactic acid bacteria was studied in a series of experiments. The main aim of the work was to increase the exopolysaccharide (EPS) production where customised milk was used as fermentation medium. It was proved that the controlling of culturing conditions and the modifying of fermentation medium conditions (i.e., carbon, nitrogen, mineral sources and vitamins) can dramatically enhance the production of the EPS. The temperature and agitation rate were critical for kefiran production during the 24 h cultivation of grains; our optimised conditions being 25°C and 80 rpm, respectively. In addition, when optimising the effects of additional nutrition, it was found that 5% (w/v) lactose, 0.1% (w/v) thiamine, and 0.1% (w/v) FeCl3 led to the maximal production of EPS. The results indicate that nutrients can be utilised to improve the production of EPS and that good kefir grains growth does not appear to be a determining factor for a high production yield of EPS. Copyright © 2013 Elsevier Ltd. All rights reserved.

Single Top quark production cross-section measurements using the ATLAS detector at the LHC

CERN Document Server

Jimenez Pena, Javier; The ATLAS collaboration

2018-01-01

Measurements of single top-quark production in proton-proton collisions are presented based on the 13 TeV and 8 TeV ATLAS datasets. In the leading order process, a W-boson is exchanged in the t-channel. The cross-section for the production of single top-quarks and single antitop-quarks, their ratio, as well as differential cross-section measurements are also reported. Measurements of the inclusive and differential cross-sections for the production of a single top quark in association with a W-boson, the second largest single top production mode are also presented. Evidence for the s-channel single top-quark production in the 8 TeV dataset is presented. Finally, the first measurement of the tZq electroweak production is presented. All measurements are compared to state-of-the art theoretical calculations. (On behalf of the ATLAS collaboration)

Patient empowerment in long-term conditions: development and preliminary testing of a new measure

Science.gov (United States)

2013-01-01

Background Patient empowerment is viewed by policy makers and health care practitioners as a mechanism to help patients with long-term conditions better manage their health and achieve better outcomes. However, assessing the role of empowerment is dependent on effective measures of empowerment. Although many measures of empowerment exist, no measure has been developed specifically for patients with long-term conditions in the primary care setting. This study presents preliminary data on the development and validation of such a measure. Methods We conducted two empirical studies. Study one was an interview study to understand empowerment from the perspective of patients living with long-term conditions. Qualitative analysis identified dimensions of empowerment, and the qualitative data were used to generate items relating to these dimensions. Study two was a cross-sectional postal study involving patients with different types of long-term conditions recruited from general practices. The survey was conducted to test and validate our new measure of empowerment. Factor analysis and regression were performed to test scale structure, internal consistency and construct validity. Results Sixteen predominately elderly patients with different types of long-term conditions described empowerment in terms of 5 dimensions (identity, knowledge and understanding, personal control, personal decision-making, and enabling other patients). One hundred and ninety seven survey responses were received from mainly older white females, with relatively low levels of formal education, with the majority retired from paid work. Almost half of the sample reported cardiovascular, joint or diabetes long-term conditions. Factor analysis identified a three factor solution (positive attitude and sense of control, knowledge and confidence in decision making and enabling others), although the structure lacked clarity. A total empowerment score across all items showed acceptable levels of internal

Population-level body condition correlates with productivity in an arctic wader, the dunlin Calidris alpina, during post-breeding migration.

Directory of Open Access Journals (Sweden)

Grzegorz Neubauer

Full Text Available Weather and predation constitute the two main factors affecting the breeding success of those Arctic waders whose productivity is highly variable over the years. We tested whether reproductive success is associated with the post-breeding condition of adults, in which in 'good' years (with warm weather, plentiful food and low predation pressure the condition of breeders and their productivity is high. To verify this hypothesis, we used a 10-year dataset comprising 20,792 dunlins Calidris alpina, trapped during migration at a stopover site on the southern Baltic Sea shore. Males were consistently in a slightly worse condition than females, likely due to male-biased parental investment in brood rearing. Annual productivity indices were positively correlated with the respective condition indices of breeders from the Eurasian Arctic, indicating that in 'good' years, despite great effort spent on reproduction, breeders leave the breeding grounds in better condition. The pattern did not hold for 1992: productivity was low, but the average condition of adults during migration was the highest noted over the decade. We suggest that the delayed effect of the Mount Pinatubo eruption in the Philippines in 1991, could be responsible for the unexpected high condition of Arctic breeders in 1992. High population-level average condition, coupled with the low productivity could stem from severe weather caused by the volcano eruption a year before and strong predation pressure, which in turn lead to a reduced investment in reproduction. The importance of large-scale episodic phenomena, like this volcano eruption, may blur the statistical associations of wildlife with local environmental drivers.

Population-level body condition correlates with productivity in an arctic wader, the dunlin Calidris alpina, during post-breeding migration.

Science.gov (United States)

Neubauer, Grzegorz; Pilacka, Lucyna; Zieliński, Piotr; Gromadzka, Jadwiga

2017-01-01

Weather and predation constitute the two main factors affecting the breeding success of those Arctic waders whose productivity is highly variable over the years. We tested whether reproductive success is associated with the post-breeding condition of adults, in which in 'good' years (with warm weather, plentiful food and low predation pressure) the condition of breeders and their productivity is high. To verify this hypothesis, we used a 10-year dataset comprising 20,792 dunlins Calidris alpina, trapped during migration at a stopover site on the southern Baltic Sea shore. Males were consistently in a slightly worse condition than females, likely due to male-biased parental investment in brood rearing. Annual productivity indices were positively correlated with the respective condition indices of breeders from the Eurasian Arctic, indicating that in 'good' years, despite great effort spent on reproduction, breeders leave the breeding grounds in better condition. The pattern did not hold for 1992: productivity was low, but the average condition of adults during migration was the highest noted over the decade. We suggest that the delayed effect of the Mount Pinatubo eruption in the Philippines in 1991, could be responsible for the unexpected high condition of Arctic breeders in 1992. High population-level average condition, coupled with the low productivity could stem from severe weather caused by the volcano eruption a year before and strong predation pressure, which in turn lead to a reduced investment in reproduction. The importance of large-scale episodic phenomena, like this volcano eruption, may blur the statistical associations of wildlife with local environmental drivers.

Removal of pharmaceutical and personal care products (PPCPs) under nitrifying and denitrifying conditions.

Science.gov (United States)

Suarez, Sonia; Lema, Juan M; Omil, Francisco

2010-05-01

The contribution of volatilization, sorption and transformation to the removal of 16 Pharmaceutical and Personal Care Products (PPCPs) in two lab-scale conventional activated sludge reactors, working under nitrifying (aerobic) and denitrifying (anoxic) conditions for more than 1.5 years, have been assessed. Pseudo-first order biological degradation rate constants (k(biol)) were calculated for the selected compounds in both reactors. Faster degradation kinetics were measured in the nitrifying reactor compared to the denitrifying system for the majority of PPCPs. Compounds could be classified according to their k(biol) into very highly (k(biol)>5Lg(SS)(-1)d(-1)), highly (1fragrances (HHCB, AHTN and ADBI) were transformed to a large extent under aerobic (>75%) and anoxic (>65%) conditions, whereas naproxen (NPX), ethinylestradiol (EE2), roxithromycin (ROX) and erythromycin (ERY) were only significantly transformed in the aerobic reactor (>80%). The anti-depressant citalopram (CTL) was moderately biotransformed under both, aerobic and anoxic conditions (>60% and >40%, respectively). Some compounds, as carbamazepine (CBZ), diazepam (DZP), sulfamethoxazole (SMX) and trimethoprim (TMP), manifested high resistance to biological transformation. Solids Retention Time (SRT(aerobic) >50d and 20d and <20d) had a slightly positive effect on the removal of FLX, NPX, CTL, EE2 and natural estrogens (increase in removal efficiencies <10%). Removal of diclofenac (DCF) in the aerobic reactor was positively affected by the development of nitrifying biomass and increased from 0% up to 74%. Similarly, efficient anoxic transformation of ibuprofen (75%) was observed after an adaptation period of 340d. Temperature (16-26 degrees C) only had a slight effect on the removal of CTL which increased in 4%.

Trends, productivity losses, and associated medical conditions among toxoplasmosis deaths in the United States, 2000-2010.

Science.gov (United States)

Cummings, Patricia L; Kuo, Tony; Javanbakht, Marjan; Sorvillo, Frank

2014-11-01

Few studies have quantified toxoplasmosis mortality, associated medical conditions, and productivity losses in the United States. We examined national multiple cause of death data and estimated productivity losses caused by toxoplasmosis during 2000-2010. A matched case-control analysis examined associations between comorbid medical conditions and toxoplasmosis deaths. In total, 789 toxoplasmosis deaths were identified during the 11-year study period. Blacks and Hispanics had the highest toxoplasmosis mortality compared with whites. Several medical conditions were associated with toxoplasmosis deaths, including human immunodeficiency virus (HIV), lymphoma, leukemia, and connective tissue disorders. The number of toxoplasmosis deaths with an HIV codiagnosis declined from 2000 to 2010; the numbers without such a codiagnosis remained static. Cumulative disease-related productivity losses for the 11-year period were nearly $815 million. Although toxoplasmosis mortality has declined in the last decade, the infection remains costly and is an important cause of preventable death among non-HIV subgroups. © The American Society of Tropical Medicine and Hygiene.

Measurements of the Vector boson production with the ATLAS Detector

CERN Document Server

Weber, Stephen Albert; The ATLAS collaboration

2018-01-01

Measurements of the Drell-Yan production of W and Z bosons at the LHC are an essential part of the ATLAS standard model physics program. These processes are a probe to understand perturbative QCD and the structure of the proton. Differential measurements of the Z boson cross section produced in association with jets can be compared to different LO and NLO MC generators to test the accuracy of these predictions. A selection of recent results are presented on varying studies of W and Z boson production.

Convexity Conditions and the Legendre-Fenchel Transform for the Product of Finitely Many Positive Definite Quadratic Forms

International Nuclear Information System (INIS)

Zhao Yunbin

2010-01-01

While the product of finitely many convex functions has been investigated in the field of global optimization, some fundamental issues such as the convexity condition and the Legendre-Fenchel transform for the product function remain unresolved. Focusing on quadratic forms, this paper is aimed at addressing the question: When is the product of finitely many positive definite quadratic forms convex, and what is the Legendre-Fenchel transform for it? First, we show that the convexity of the product is determined intrinsically by the condition number of so-called 'scaled matrices' associated with quadratic forms involved. The main result claims that if the condition number of these scaled matrices are bounded above by an explicit constant (which depends only on the number of quadratic forms involved), then the product function is convex. Second, we prove that the Legendre-Fenchel transform for the product of positive definite quadratic forms can be expressed, and the computation of the transform amounts to finding the solution to a system of equations (or equally, finding a Brouwer's fixed point of a mapping) with a special structure. Thus, a broader question than the open 'Question 11' in Hiriart-Urruty (SIAM Rev. 49, 225-273, 2007) is addressed in this paper.

Work climate and work load measurement in production room of Batik Merak Manis Laweyan

Science.gov (United States)

Suhardi, Bambang; Simanjutak, Sry Yohana; Laksono, Pringgo Widyo; Herjunowibowo, Dewanto

2017-11-01

The work environment is everything around the labours that can affect them in the exercise of duties and work that is charged. In a work environment, there are workplace climate and workload which affect the labour in force carrying out its work. The working climate is one of the physical factors that could potentially cause health problems towards labour at extreme conditions of hot and cold that exceed the threshold limit value allowed by the standards of health. The climate works closely related to the workload accepted by workers in the performance of their duties. The influence of workload is pretty dominant against the performance of human resources and may cause negative effects to the safety and health of the labours. This study aims to measure the effect of the work climate and the workload against workers productivity. Furthermore, some suggestions to increase the productivity also been recommended. The research conducted in production room of Batik Merak Manis Laweyan. The results showed that the workplace climate and the workload at eight stations in production room of Merak Manis does not agree to the threshold limit value that has been set. Therefore, it is recommended to add more opening windows to add air velocity inside the building thus the humidity and temperature might be reduced.

Microalgae for high-value compounds and biofuels production: a review with focus on cultivation under stress conditions.

Science.gov (United States)

Markou, Giorgos; Nerantzis, Elias

2013-12-01

Microalgal biomass as feedstock for biofuel production is an attracting alternative to terrestrial plant utilization for biofuels production. However, today the microalgal cultivation systems for energy production purposes seem not yet to be economically feasible. Microalgae, though cultivated under stress conditions, such as nutrient starvation, high salinity, high temperature etc. accumulate considerable amounts (up to 60-65% of dry weight) of lipids or carbohydrates along with several secondary metabolites. Especially some of the latter are valuable compounds with an enormous range of industrial applications. The simultaneous production of lipids or carbohydrates for biofuel production and of secondary metabolites in a biorefinery concept might allow the microalgal production to be economically feasible. This paper aims to provide a review on the available literature about the cultivation of microalgae for the accumulation of high-value compounds along with lipids or carbohydrates focusing on stress cultivation conditions. © 2013.

Effect of Light Intensities and Atmospheric Gas Conditions on Biohydrogen Production of Microalgae Isolated from Fisheries Wastewater

Directory of Open Access Journals (Sweden)

Mujalin Pholchan

2017-06-01

Full Text Available Recently, the fishery farming industry has been developed rapidly due to increasing demand and consumption as well as the depletion of wild fish resources. Production processes in the industry usually generate large amounts of wastewater containing high nutrients, posing a threat to downstream water. However, phytoplankton removal techniques commonly used to counteract the threat, though appearing to have low efficiency, are timeconsuming and less sustainable. Microalgae are photosynthetic microorganisms that convert solar energy into hydrogen. Using the isolated algae from fish farms as a source of renewable energy production could be a promising choice for handling fisheries wastewater in a more efficient manner. However, hydrogen production processes from algae still need more studies as their efficiencies vary between algae species and growth factors. In this work, the efficiency of hydrogen production from Scenedesmus accuminatus and Arthrospira platensis harvested from fish farms under three different light intensity conditions and three atmospheric gas conditions was determined. The results showed that the best conditions for hydrogen production from both species included 24 h darkness and carbon dioxide addition. Under the atmospheric gas combination of 99% argon and 1% carbon dioxide, S. accuminatus could produce hydrogen gas as high as 0.572 mol H2/mgCh h within 12 h, while the highest hydrogen production (0.348 mol H2/mgCh h obtained from A. platensis was found under the atmospheric gas mixture of 98% argon and 2% carbon dioxide. Interestingly, S. accuminatus appeared to produce more hydrogen than A. platensis under the same conditions.

Modeling real conditions of 'Ukrytie' object in 3D measurement

International Nuclear Information System (INIS)

Podbereznyj, S.S.

2001-01-01

The article covers a technology of creation on soft products basis for designing: AutoCad, and computer graphics and animation 3D Studio, 3DS MAX, of 3D model of geometrical parameters of current conditions of building structures, technological equipment, fuel-containing materials, concrete, water of ruined Unit 4, 'Ukryttia' object, of Chernobyl NPP. The model built using the above technology will be applied in the future as a basis when automating the design and computer modeling of processes at the 'Ukryttia' object

Optimization of fermentation conditions for 1,3-propanediol production by marine Klebsiella pneumonia HSL4 using response surface methodology

Science.gov (United States)

Li, Lili; Zhou, Sheng; Ji, Huasong; Gao, Ren; Qin, Qiwei

2014-09-01

The industrially important organic compound 1,3-propanediol (1,3-PDO) is mainly used as a building block for the production of various polymers. In the present study, response surface methodology protocol was followed to determine and optimize fermentation conditions for the maximum production of 1,3-PDO using marine-derived Klebsiella pneumoniae HSL4. Four nutritional supplements together with three independent culture conditions were optimized as follows: 29.3 g/L glycerol, 8.0 g/L K2 HPO4, 7.6 g/L (NH4)2 SO4, 3.0 g/L KH2 PO4, pH 7.1, cultivation at 35°C for 12 h. Under the optimal conditions, a maximum 1,3-PDO concentration of 14.5 g/L, a productivity of 1.21 g/(L·h) and a conversion of glycerol of 0.49 g/g were obtained. In comparison with the control conditions, fermentation under the optimized conditions achieved an increase of 38.8% in 1,3-PDO concentration, 39.0% in productivity and 25.7% in glycerol conversion in flask. This enhancement trend was further confirmed when the fermentation was conducted in a 5-L fermentor. The optimized fermentation conditions could be an important basis for developing lowcost, large-scale methods for industrial production of 1,3-PDO in the future.

Analysis of corrosion product transport in PWR primary system under non-convective condition

International Nuclear Information System (INIS)

Han, Byoung Sub

1992-02-01

The increase of occupational radiation exposure (ORE) due to the increase of the operational period at existing nuclear power plant and also the publication of the new version of ICRP recommendation (ICRP publication No. 60) for radiological protection require much more strict reduction of radiation buildup in the nuclear power plant. The major sources of the radiation, i.e. the radioactive corrosion-products, are generated by the neutron activation of the corrosion products at the reactor core, and then the radioactive corrosion products are transported to the outside of the core, and accumulated near the steam generator side at PWR. Major radioactive corrosion-products of interest in PWR are Cr 51 ,: Mn 54 ,: Co 58 ,: Fe 59 and Co 60 . Among them Co 58 and Co 60 are known to contribute approximately more than 70% of the total ORE. Thus our main concerns are focused on predicting the transport and deposition of the Co radionuclides and suggesting the optimizing method which can minimize and control the ORE of the nuclear power plant. It is well known that Co-source is most effectively controlled by pH-solubility radiation control, and also some complex computer codes such as CORA and PACTOLE have been developed and revised to predict the corrosion product behavior. However these codes still imply some intrisic problems in simulating the real behavior of corrosion products in the reactor because of 1) the lack of important experimental data, coefficients and parameters of the transport and reactions under actual high temperature and pressure conditions, 2) no general theoretical modelling which can describe such many different mechanisms involved in the corrosion product movements, 3) the newly developed and measured behavior of the corrosion product transport mechanism. Since no sufficient and detailed information is available from the above-mentioned codes (also due to propriority problems), we concentrate on developing a new computer code, CP-TRAN (Corrosion

In situ trace gas and particle measurements in the summer lower stratosphere during STREAM II. Implications for O{sub 3} production

Energy Technology Data Exchange (ETDEWEB)

Bregman, A; Lelieveld, J; Scheeren, H A [Institute for Marine and Atmospheric Sciences, Utrecht (Netherlands); Arnold, F; Buerger, V; Schneider, J [Max-Planck-Inst. for Nuclear Physics, Heidelberg (Germany); Fischer, H; Waibel, A [Max-Planck-Inst. fuer Chemie, Mainz (Germany); Siegmund, P C; Wauben, W M.F. [Koninklijk Nederlands Meteorologisch Inst., De Bilt (Netherlands); Stroem, J [Stockholm Univ. (Sweden). Dept. of Meteorology

1998-12-31

In situ aircraft measurements of O{sub 3}, CO, HNO{sub 3}, and aerosol particles are presented, performed over the North Sea region in the summer lower stratosphere during the STREAM-II campaign (Stratosphere Troposphere Experiments by Aircraft Measurements). Elevated CO mixing ratios are attributed to mixing of polluted tropospheric air into the lowermost extra-tropical stratosphere. Model calculations illustrate that the O{sub 3} production efficiency of NO{sub x} is smaller than previously assumed, under conditions with relatively high HNO{sub 3} mixing ratios, as observed during STREAM-II. The model simulations further suggest a relatively high O{sub 3} production efficiency from CO oxidation, as a result of the relatively high ambient HNO{sub 3} and NO{sub x} concentrations, implying that upward transport of CO rich air enhances O{sub 3} production in the lowermost stratosphere. (author) 13 refs.

In situ trace gas and particle measurements in the summer lower stratosphere during STREAM II. Implications for O{sub 3} production

Energy Technology Data Exchange (ETDEWEB)

Bregman, A.; Lelieveld, J.; Scheeren, H.A. [Institute for Marine and Atmospheric Sciences, Utrecht (Netherlands); Arnold, F.; Buerger, V.; Schneider, J. [Max-Planck-Inst. for Nuclear Physics, Heidelberg (Germany); Fischer, H.; Waibel, A. [Max-Planck-Inst. fuer Chemie, Mainz (Germany); Siegmund, P.C.; Wauben, W.M.F. [Koninklijk Nederlands Meteorologisch Inst., De Bilt (Netherlands); Stroem, J. [Stockholm Univ. (Sweden). Dept. of Meteorology

1997-12-31

In situ aircraft measurements of O{sub 3}, CO, HNO{sub 3}, and aerosol particles are presented, performed over the North Sea region in the summer lower stratosphere during the STREAM-II campaign (Stratosphere Troposphere Experiments by Aircraft Measurements). Elevated CO mixing ratios are attributed to mixing of polluted tropospheric air into the lowermost extra-tropical stratosphere. Model calculations illustrate that the O{sub 3} production efficiency of NO{sub x} is smaller than previously assumed, under conditions with relatively high HNO{sub 3} mixing ratios, as observed during STREAM-II. The model simulations further suggest a relatively high O{sub 3} production efficiency from CO oxidation, as a result of the relatively high ambient HNO{sub 3} and NO{sub x} concentrations, implying that upward transport of CO rich air enhances O{sub 3} production in the lowermost stratosphere. (author) 13 refs.

LEP measurements on production, mass, lifetime of beauty particles

International Nuclear Information System (INIS)

Wormser, G.

1993-10-01

Present knowledge about the individual properties of the different beauty particles is discussed using the results of the LEP experiments. Individual lifetimes for B d 0 and B + are found to be equal within 10% whilst a 15% precision is reached for B s 0 and Λ b . The Λ b lifetime is found to be smaller than τ B + with a 2.7 σ significance. The production rate of each of these particles is measured at the 20% level. Preliminary evidence for Ξ b production has been reported. Finally, the B s 0 meson mass has been measured to be 5373 ± 4 MeV/c 2 . (author) 24 refs., 9 figs., 5 tabs

Quantitative approach for optimizing e-beam condition of photoresist inspection and measurement

Science.gov (United States)

Lin, Chia-Jen; Teng, Chia-Hao; Cheng, Po-Chung; Sato, Yoshishige; Huang, Shang-Chieh; Chen, Chu-En; Maruyama, Kotaro; Yamazaki, Yuichiro

2018-03-01

Severe process margin in advanced technology node of semiconductor device is controlled by e-beam metrology system and e-beam inspection system with scanning electron microscopy (SEM) image. By using SEM, larger area image with higher image quality is required to collect massive amount of data for metrology and to detect defect in a large area for inspection. Although photoresist is the one of the critical process in semiconductor device manufacturing, observing photoresist pattern by SEM image is crucial and troublesome especially in the case of large image. The charging effect by e-beam irradiation on photoresist pattern causes deterioration of image quality, and it affect CD variation on metrology system and causes difficulties to continue defect inspection in a long time for a large area. In this study, we established a quantitative approach for optimizing e-beam condition with "Die to Database" algorithm of NGR3500 on photoresist pattern to minimize charging effect. And we enhanced the performance of measurement and inspection on photoresist pattern by using optimized e-beam condition. NGR3500 is the geometry verification system based on "Die to Database" algorithm which compares SEM image with design data [1]. By comparing SEM image and design data, key performance indicator (KPI) of SEM image such as "Sharpness", "S/N", "Gray level variation in FOV", "Image shift" can be retrieved. These KPIs were analyzed with different e-beam conditions which consist of "Landing Energy", "Probe Current", "Scanning Speed" and "Scanning Method", and the best e-beam condition could be achieved with maximum image quality, maximum scanning speed and minimum image shift. On this quantitative approach of optimizing e-beam condition, we could observe dependency of SEM condition on photoresist charging. By using optimized e-beam condition, measurement could be continued on photoresist pattern over 24 hours stably. KPIs of SEM image proved image quality during measurement and

Conditional stability for a single interior measurement

International Nuclear Information System (INIS)

Honda, Naofumi; McLaughlin, Joyce; Nakamura, Gen

2014-01-01

An inverse problem to identify unknown coefficients of a partial differential equation by a single interior measurement is considered. The equation considered in this paper is a strongly elliptic second order scalar equation which can have complex coefficients in a bounded domain with C 2 boundary. We are given a single interior measurement. This means that we know a given solution of the forward equation in this domain. The equation includes some model equations arising from acoustics, viscoelasticity and hydrology. We assume that the coefficients are piecewise analytic. Our major result is the local Hölder stability estimate for identifying the unknown coefficients. If the unknown coefficient is a complex coefficient in the principal part of the equation, we assumed a condition which we name admissibility assumption for the real part and imaginary part of the difference of two complex coefficients. This admissibility assumption is automatically satisfied if the complex coefficients are real valued. For identifying either the real coefficient in the principal part or the coefficient of the 0th order of the equation, the major result implies global uniqueness for the identification. (paper)

NMR chemical shift and J coupling parameterization and quantum mechanical reference spectrum simulation for selected nerve agent degradation products in aqueous conditions.

Science.gov (United States)

Koskela, Harri; Anđelković, Boban

2017-10-01

The spectral parameters of selected nerve agent degradation products relevant to the Chemical Weapons Convention, namely, ethyl methylphosphonate, isopropyl methylphosphonate, pinacolyl methylphosphonate and methylphosphonic acid, were studied in wide range of pH conditions and selected temperatures. The pH and temperature dependence of chemical shifts and J couplings was parameterized using Henderson-Hasselbalch-based functions. The obtained parameters allowed calculation of precise chemical shifts and J coupling constants in arbitrary pH conditions and typical measurement temperatures, thus facilitating quantum mechanical simulation of reference spectra in the chosen magnetic field strength for chemical verification. Copyright © 2017 John Wiley & Sons, Ltd. Copyright © 2017 John Wiley & Sons, Ltd.

Measurements of the vector boson production with the ATLAS detector

Science.gov (United States)

Lapertosa, A.

2018-01-01

Measurements of the Drell-Yan production of W and Z bosons at the LHC provide a benchmark of our understanding of perturbative QCD and probe the proton structure in a unique way. The ATLAS collaboration has performed new high precision measurements at a center-of-mass energy of 7 TeV. The measurements are performed for W+, W- and Z bosons integrated and as a function of the boson or lepton rapidity and the Z mass. Unprecedented precision is reached and strong constraints on Parton Distribution Functions, in particular the strange density are found. Z boson cross sections are also measured at center-of-mass energies of 8 TeV and 13 TeV, and cross-section ratios to the top-quark pair production have been derived. This ratio measurement leads to a cancellation of systematic effects and allows for a high precision comparison to the theory predictions. The production of jets in association with vector bosons is a further important process to study perturbative QCD in a multi-scale environment. The ATLAS collaboration has performed new measurements of Z boson plus jets cross sections, differential in several kinematic variables, in proton-proton collision data taken at a center-of-mass energy of 13 TeV. The measurements are compared to state-of-the art theory predictions. They are sensitive to higher-order pQCD effects, probe flavour and mass schemes and can be used to constrain the proton structure. In addition, a new measurement of the splitting scales of the kt jet-clustering algorithm for final states containing a Z boson candidate at a center-of-mass energy of 8 TeV is presented.

Growth, photosynthetic pigments and production of essential oil of long-pepper under different light conditions

Directory of Open Access Journals (Sweden)

VANDIMILLI A. LIMA

Full Text Available ABSTRACT Piper hispidinervum C. DC. is popularly known as long-pepper and it owns a commercial value due to the essential oil it produces. Long-pepper oil is rich in safrole and eugenoln components that have insecticidal, fungicidal and bactericidal activity. It has been establish that to medicinal plants light influences not only growth but also essential oil production. The growth, the content of photosynthetic pigments and the essential oil production of Piper hispidinervum at greenhouses with different light conditions was evaluated. The treatments were characterized by cultivation of plants for 180 days under different light conditions, produced by shading greenhouses with 50% and 30% of natural incident irradiance, two colored shading nets red (RN and blue (BN both blocking 50% of the incident radiation and one treatment at full-sun (0% of shade. The results showed that the treatments of 50% shade and RN and BN were the ones which stimulated the greater growth. Blue and red light also had the best production of photosynthetic pigments. Essential oil yielded more under full sun therefore this is the most indicated condition to produce seedlings for the chemical and pharmaceutical industry.

Growth, photosynthetic pigments and production of essential oil of long-pepper under different light conditions.

Science.gov (United States)

Lima, Vandimilli A; Pacheco, Fernanda V; Avelar, Rafaella P; Alvarenga, Ivan C A; Pinto, José Eduardo B P; Alvarenga, Amauri A DE

2017-01-01

Piper hispidinervum C. DC. is popularly known as long-pepper and it owns a commercial value due to the essential oil it produces. Long-pepper oil is rich in safrole and eugenoln components that have insecticidal, fungicidal and bactericidal activity. It has been establish that to medicinal plants light influences not only growth but also essential oil production. The growth, the content of photosynthetic pigments and the essential oil production of Piper hispidinervum at greenhouses with different light conditions was evaluated. The treatments were characterized by cultivation of plants for 180 days under different light conditions, produced by shading greenhouses with 50% and 30% of natural incident irradiance, two colored shading nets red (RN) and blue (BN) both blocking 50% of the incident radiation and one treatment at full-sun (0% of shade). The results showed that the treatments of 50% shade and RN and BN were the ones which stimulated the greater growth. Blue and red light also had the best production of photosynthetic pigments. Essential oil yielded more under full sun therefore this is the most indicated condition to produce seedlings for the chemical and pharmaceutical industry.

On-line tritium production and heat deposition rate measurements at the Lotus facility

International Nuclear Information System (INIS)

Joneja, O.P.; Scherrer, P.; Anand, R.P.

1994-01-01

Integral tritium production and heat deposition measurement in a prototype fusion blanket would enable verification of the computational codes and the data based employed for the calculations. A large number of tritium production rate measurements have been reported for different type of blankets, whereas the direct heat deposition due to the mixed radiation field in the fusion environment, is still in its infancy. In order to ascertain the kerma factors and the photon production libraries, suitable techniques must be developed to directly measure the nuclear heat deposition rates in the materials required for the fusion systems. In this context, at the Lotus facility, we have developed an extremely efficient double ionizing chamber, for the on-line tritium production measurements and employed a pure graphite calorimeter to measure the nuclear heat deposition due to the mixed radiation field of the 14 MeV, Haefely neutron generator. This paper presents both systems and some of the recent measurements. (authors). 8 refs., 13 figs

Optimization of fermentation conditions for the production of curcumin by engineered Escherichia coli.

Science.gov (United States)

Couto, Márcia R; Rodrigues, Joana L; Rodrigues, Lígia R

2017-08-01

Curcumin is a plant secondary metabolite with outstanding therapeutic effects. Therefore, there is a great interest in developing new strategies to produce this high-value compound in a cheaper and environmentally friendly way. Curcumin heterologous production in Escherichia coli using artificial biosynthetic pathways was previously demonstrated using synthetic biology approaches. However, the culturing conditions to produce this compound were not optimized and so far only a two-step fermentation process involving the exchange of culture medium allowed high concentrations of curcumin to be obtained, which limits its production at an industrial scale. In this study, the culturing conditions to produce curcumin were evaluated and optimized. In addition, it was concluded that E. coli BL21 allows higher concentrations of curcumin to be produced than E. coli K-12 strains. Different isopropyl β-d-thiogalactopyranoside concentrations, time of protein expression induction and substrate type and concentration were also evaluated. The highest curcumin production obtained was 959.3 µM (95.93% of per cent yield), which was 3.1-fold higher than the highest concentration previously reported. This concentration was obtained using a two-stage fermentation with lysogeny broth (LB) and M9. Moreover, terrific broth was also demonstrated to be a very interesting alternative medium to produce curcumin because it also led to high concentrations (817.7 µM). The use of this single fermentation medium represents an advantage at industrial scale and, although the final production is lower than that obtained with the LB-M9 combination, it leads to a significantly higher production of curcumin in the first 24 h of fermentation. This study allowed obtaining the highest concentrations of curcumin reported so far in a heterologous organism and is of interest for all of those working with the heterologous production of curcuminoids, other complex polyphenolic compounds or plant secondary

Latest LHCb measurements of Electroweak Boson Production in Run-1

CERN Document Server

CERN. Geneva

2015-01-01

We present the latest LHCb measurements of forward Electroweak Boson Production using proton-proton collisions recorded in LHC Run-1. The seminar shall discuss measurements of the 8 TeV W & Z boson production cross-sections. These results make use of LHCb's excellent integrated luminosity determination to provide constraints on the parton distribution functions which describe the inner structure of the proton. These LHCb measurements probe a region of phase space at low Bjorken-x where the other LHC experiments have limited sensitivity. We also present measurements of cross-section ratios, and ratios of results in 7 TeV and 8 TeV proton-proton collisions. These results provide precision tests of the Standard Model. The seminar shall also present a measurement of the forward-backward asymmetry (A_FB) in Z boson decays to two muons. This result allows for precision tests of the coupling of the Z boson to left and right handed particles, providing sensitivity to the effective weak mixing angle (...

Measurement of W/Z production with the ATLAS detector

CERN Document Server

Sauvan, JB; The ATLAS collaboration

2012-01-01

The production of W and Z bosons at the LHC has been measured with the ATLAS detector. These measurements include inclusive and differential cross sections, $W$ polarisation, and the polarisation of tau leptons from W decays. They show sensitivity to the proton structure and are also used to test predictions from perturbative QCD and phenomenological models.

Identification of complex model thermal boundary conditions based on exterior temperature measurement

International Nuclear Information System (INIS)

Lu Jianming; Ouyang Guangyao; Zhang Ping; Rong Bojun

2012-01-01

Combining the advantages of the finite element software in temperature field analyzing with the multivariate function optimization arithmetic, a feasibility method based on the exterior temperature was proposed to get the thermal boundary conditions, which was required in temperature field analyzing. The thermal boundary conditions can be obtained only by some temperature measurement values. Taking the identification of the convection heat transfer coefficient of a high power density diesel engine cylinder head as an example, the calculation result shows that when the temperature measurement error was less than 0.5℃, the maximum relative error was less than 2%. It is shown that the new method was feasible (authors)

Optimization of the production conditions of the lipase produced by Bacillus cereus from rice flour through Plackett-Burman Design (PBD) and response surface methodology (RSM).

Science.gov (United States)

Vasiee, Alireza; Behbahani, Behrooz Alizadeh; Yazdi, Farideh Tabatabaei; Moradi, Samira

2016-12-01

In this study, the screening of lipase positive bacteria from rice flour was carried out by Rhodamin B agar plate method. Bacillus cereus was identified by 16S rDNA method. Screening of the appropriate variables and optimization of the lipase production was performed using Plackett-Burman design (PBD) and response surface methodology (RSM). Among the isolated bacteria, an aerobic Bacillus cereus strain was recognized as the best lipase-producing bacteria (177.3 ± 20 U/ml). Given the results, the optimal enzyme production conditions were achieved with coriander seed extract (CSE)/yeast extract ratio of 16.9 w/w, olive oil (OO) and MgCl 2 concentration of 2.37 g/L and 24.23 mM, respectively. In these conditions, the lipase activity (LA) was predicted 343 U/mL that was approximately close to the predicted value (324 U/mL), which was increased 1.83 fold LA compared with the non-optimized lipase. The kinetic parameters of V max and K m for the lipase were measured 0.367 μM/min.mL and 5.3 mM, respectively. The lipase producing Bacillus cereus was isolated and RSM was used for the optimization of enzyme production. The CSE/yeast extract ratio of 16.9 w/w, OO concentration of 2.37 g/L and MgCl 2 concentration of 24.23 mM, were found to be the optimal conditions of the enzyme production process. LA at optimal enzyme production conditions was observed 1.83 times more than the non-optimal conditions. Ultimately, it can be concluded that the isolated B. cereus from rice flour is a proper source of lipase. Copyright © 2016 Elsevier Ltd. All rights reserved.

Method s for Measuring Productivity in Libraries and Information Centres

OpenAIRE

Mohammad Alaaei

2009-01-01

  Within Information centers, productivity is the result of optimal and effective use of information resources, service quality improvement, increased user satisfaction, pleasantness of working environment, increased motivation and enthusiasm of staff to work better. All contribute to the growth and development of information centers. Thus these centers would need to be familiar with methods employed in productivity measurement. Productivity is one of the criteria for evaluating system perfor...

Energy production from grassland - Assessing the sustainability of different process chains under German conditions

International Nuclear Information System (INIS)

Roesch, Christine; Skarka, J.; Raab, K.; Stelzer, V.

2009-01-01

In many regions of Europe, grassland shapes the landscape and fulfils important functions in protecting nature, soil, and water. However, the traditional uses of grassland for forage production are vanishing with progress in breeding and structural adaptations in agriculture. On the other hand, the demand for biomass energy is rising due to political sustainability goals and financial measures to support renewable energy. Against this background, the Institute for Technology Assessment and Systems Analysis investigated the applicability, economic efficiency, and sustainability of different techniques for energy production from grassland as well as from grassland converted into maize fields or short-rotation poplars under German conditions. The results show that despite relatively high energy prices and the financial support for bioenergy, the effects of energy production from grassland on employment in agriculture and farmers' income are modest. What is beneficial are savings in non-renewable energy, reductions in greenhouse gas emissions, and local provision of energy carriers. If grassland biomass (grass silage or hay) is used for energy purposes, this brings the further advantages of preserving biodiversity and the cultural landscape and protecting of soil and groundwater. Negative impacts on sustainable development result from an increase in emissions, which leads to acidification, eutrophication, and risks to human health. The overall evaluation indicates that short-rotation poplars are comparatively advantageous from the economic and ecological point of view. Therefore, a development plan for grassland is required to identify areas where grassland could be used as an energy resource or where it would be favourable to install energy plantations with fast-growing perennial plants

Monte Carlo Method with Heuristic Adjustment for Irregularly Shaped Food Product Volume Measurement

Directory of Open Access Journals (Sweden)

Joko Siswantoro

2014-01-01

Full Text Available Volume measurement plays an important role in the production and processing of food products. Various methods have been proposed to measure the volume of food products with irregular shapes based on 3D reconstruction. However, 3D reconstruction comes with a high-priced computational cost. Furthermore, some of the volume measurement methods based on 3D reconstruction have a low accuracy. Another method for measuring volume of objects uses Monte Carlo method. Monte Carlo method performs volume measurements using random points. Monte Carlo method only requires information regarding whether random points fall inside or outside an object and does not require a 3D reconstruction. This paper proposes volume measurement using a computer vision system for irregularly shaped food products without 3D reconstruction based on Monte Carlo method with heuristic adjustment. Five images of food product were captured using five cameras and processed to produce binary images. Monte Carlo integration with heuristic adjustment was performed to measure the volume based on the information extracted from binary images. The experimental results show that the proposed method provided high accuracy and precision compared to the water displacement method. In addition, the proposed method is more accurate and faster than the space carving method.

Monte Carlo method with heuristic adjustment for irregularly shaped food product volume measurement.

Science.gov (United States)

Siswantoro, Joko; Prabuwono, Anton Satria; Abdullah, Azizi; Idrus, Bahari

2014-01-01

Volume measurement plays an important role in the production and processing of food products. Various methods have been proposed to measure the volume of food products with irregular shapes based on 3D reconstruction. However, 3D reconstruction comes with a high-priced computational cost. Furthermore, some of the volume measurement methods based on 3D reconstruction have a low accuracy. Another method for measuring volume of objects uses Monte Carlo method. Monte Carlo method performs volume measurements using random points. Monte Carlo method only requires information regarding whether random points fall inside or outside an object and does not require a 3D reconstruction. This paper proposes volume measurement using a computer vision system for irregularly shaped food products without 3D reconstruction based on Monte Carlo method with heuristic adjustment. Five images of food product were captured using five cameras and processed to produce binary images. Monte Carlo integration with heuristic adjustment was performed to measure the volume based on the information extracted from binary images. The experimental results show that the proposed method provided high accuracy and precision compared to the water displacement method. In addition, the proposed method is more accurate and faster than the space carving method.

LHCb: Measurement of $J/\\psi$ production cross-section at LHCb

CERN Multimedia

Zhang, Y

2011-01-01

The measurement of the $J/\\psi$ production cross-section with the LHCb detector is presented. The cross-section is measured as a function of the $J/\\psi$ transverse momentum and rapidity, in the forward region. Contributions from prompt $J/\\psi$ and $J/\\psi$ from $b$ are measured separately. Prospects for measurements of the $J/\\psi$ polarisation with a full angular analysis are also shown.

Assessment of GPM-IMERG and Other Precipitation Products against Gauge Data under Different Topographic and Climatic Conditions in Iran: Preliminary Results

Directory of Open Access Journals (Sweden)

Ehsan Sharifi

2016-02-01

Full Text Available The new generation of weather observatory satellites, namely Global Precipitation Measurement (GPM constellation satellites, is the lead observatory of the 10 highly advanced earth orbiting weather research satellites. Indeed, GPM is the first satellite that has been designed to measure light rain and snowfall, in addition to heavy tropical rainfall. This work compares the final run of the Integrated Multi-satellitE Retrievals for GPM (IMERG product, the post real time of TRMM and Multi-satellite Precipitation Analysis (TMPA-3B42 and the Era-Interim product from the European Centre for Medium Range Weather Forecasts (ECMWF against the Iran Meteorological Organization (IMO daily precipitation measured by the synoptic rain-gauges over four regions with different topography and climate conditions in Iran. Assessment is implemented for a one-year period from March 2014 to February 2015. Overall, in daily scale the results reveal that all three products lead to underestimation but IMERG performs better than other products and underestimates precipitation slightly in all four regions. Based on monthly and seasonal scale, in Guilan all products, in Bushehr and Kermanshah ERA-Interim and in Tehran IMERG and ERA-Interim tend to underestimate. The correlation coefficient between IMERG and the rain-gauge data in daily scale is far superior to that of Era-Interim and TMPA-3B42. On the basis of daily timescale of bias in comparison with the ground data, the IMERG product far outperforms ERA-Interim and 3B42 products. According to the categorical verification technique in this study, IMERG yields better results for detection of precipitation events on the basis of Probability of Detection (POD, Critical Success Index (CSI and False Alarm Ratio (FAR in those areas with stratiform and orographic precipitation, such as Tehran and Kermanshah, compared with other satellite/model data sets. In particular, for heavy precipitation (>15 mm/day, IMERG is superior to

The Eocene Arctic Azolla bloom: environmental conditions, productivity and carbon drawdown.

Science.gov (United States)

Speelman, E N; Van Kempen, M M L; Barke, J; Brinkhuis, H; Reichart, G J; Smolders, A J P; Roelofs, J G M; Sangiorgi, F; de Leeuw, J W; Lotter, A F; Sinninghe Damsté, J S

2009-03-01

Enormous quantities of the free-floating freshwater fern Azolla grew and reproduced in situ in the Arctic Ocean during the middle Eocene, as was demonstrated by microscopic analysis of microlaminated sediments recovered from the Lomonosov Ridge during Integrated Ocean Drilling Program (IODP) Expedition 302. The timing of the Azolla phase (approximately 48.5 Ma) coincides with the earliest signs of onset of the transition from a greenhouse towards the modern icehouse Earth. The sustained growth of Azolla, currently ranking among the fastest growing plants on Earth, in a major anoxic oceanic basin may have contributed to decreasing atmospheric pCO2 levels via burial of Azolla-derived organic matter. The consequences of these enormous Azolla blooms for regional and global nutrient and carbon cycles are still largely unknown. Cultivation experiments have been set up to investigate the influence of elevated pCO2 on Azolla growth, showing a marked increase in Azolla productivity under elevated (760 and 1910 ppm) pCO2 conditions. The combined results of organic carbon, sulphur, nitrogen content and 15N and 13C measurements of sediments from the Azolla interval illustrate the potential contribution of nitrogen fixation in a euxinic stratified Eocene Arctic. Flux calculations were used to quantitatively reconstruct the potential storage of carbon (0.9-3.5 10(18) gC) in the Arctic during the Azolla interval. It is estimated that storing 0.9 10(18) to 3.5 10(18) g carbon would result in a 55 to 470 ppm drawdown of pCO2 under Eocene conditions, indicating that the Arctic Azolla blooms may have had a significant effect on global atmospheric pCO2 levels through enhanced burial of organic matter.

Open-charm production measurements with ALICE at the LHC

International Nuclear Information System (INIS)

Pagano, P.

2016-01-01

The LHC heavy-ion physics program aims at investigating the properties of strongly-interacting matter under extreme conditions of temperature and energy density where the formation of the Quark-Gluon Plasma (QGP) is expected. Heavy-flavour hadrons, containing charm and beauty quarks, are considered efficient probes to investigate the properties of the QGP produced in heavy-ion collisions. Heavy quarks are produced in hard partonic scattering processes in the initial stage of hadronic collisions and propagate through the hot and dense medium created in the collision losing energy interacting with the medium via radiative and collisional processes. The high precision tracking, good vertexing capabilities and excellent particle identification offered by the ALICE experiment allow us to measure particles containing heavy quarks in a wide transversemomentum range in pp, p-Pb and Pb-Pb collisions. A review of the main results on prompt D-mesons production, reconstructed via their hadronic decays at mid-rapidity, in pp collisions at √s = 7 TeV, p-Pb collisions at √s_N_N = 5.02 TeV and Pb-Pb collisions at √s_N_N = 2.76 TeV will be shown

Chronic condition self-management surveillance: what is and what should be measured?

Science.gov (United States)

Ruiz, Sarah; Brady, Teresa J; Glasgow, Russell E; Birkel, Richard; Spafford, Michelle

2014-06-19

The rapid growth in chronic disease prevalence, in particular the prevalence of multiple chronic conditions, poses a significant and increasing burden on the health of Americans. Maximizing the use of proven self-management (SM) strategies is a core goal of the US Department of Health and Human Services. Yet, there is no systematic way to assess how much SM or self-management support (SMS) is occurring in the United States. The purpose of this project was to identify appropriate concepts or measures to incorporate into national SM and SMS surveillance. A multistep process was used to identify candidate concepts, assess existing measures, and select high-priority concepts for further development. A stakeholder survey, an environmental scan, subject matter expert feedback, and a stakeholder priority-setting exercise were all used to select the high-priority concepts for development. The stakeholder survey gathered feedback on 32 candidate concepts; 9 concepts were endorsed by more than 66% of respondents. The environmental scan indicated few existing measures that adequately reflected the candidate concepts, and those that were identified were generally specific to a defined condition and not gathered on a population basis. On the basis of the priority setting exercises and environmental scan, we selected 1 concept from each of 5 levels of behavioral influence for immediate development as an SM or SMS indicator. The absence of any available measures to assess SM or SMS across the population highlights the need to develop chronic condition SM surveillance that uses national surveys and other data sources to measure national progress in SM and SMS.

Green Fodder Production and Water Use Efficiency of Some Forage Crops under Hydroponic Conditions

OpenAIRE

Ghazi N. Al-Karaki; M. Al-Hashimi

2012-01-01

The objectives of this study were to evaluate five forage crops (alfalfa (Medicago sativa), barley (Hordeum vulgare), cowpea (Vigna unguiculata), sorghum (Sorghum bicolor), and wheat (Triticum aestivum)) for green fodder production and water use efficiency under hydroponic conditions. The experiment has been conducted under temperature-controlled conditions (24 ± 1°C) and natural window illumination at growth room of Soilless Culture Laboratory, Arabian Gulf University, Manama, Bahrain. The r...

Accredited dose measurements for validation of radiation sterilized products

DEFF Research Database (Denmark)

Miller, A.

1993-01-01

for control of radiation sterilization. The accredited services include: 1. 1. Irradiation of dosimeters and test samples with cobalt-60 gamma rays. 2. 2. Irradiation of dosimeters and test samples with 10 MeV electrons. 3. 3. Issue of and measurement with calibrated dosimeters. 4. 4. Measurement...... of the dosimetric parameters of an irradiation facility. 5. 5. Measurement of absorbed dose distribution in irradiated products. The paper describes these services and the procedures necessary for their execution....

Experimental investigation on local parameter measurement using optical probes in two-phase flow under rolling condition

International Nuclear Information System (INIS)

Tian Daogui; Sun Licheng; Yan Changqi; Liu Guoqiang

2013-01-01

In order to get more local interfacial information as well as to further comprehend the intrinsic mechanism of two-phase flow under rolling condition, a method was proposed to measure the local parameters by using optical probes under rolling condition in this paper. An experimental investigation of two-phase flow under rolling condition was conducted using the probe fabricated by the authors. It is verified that the probe method is feasible to measure the local parameters in two'-phase flow under rolling condition. The results show that the interfacial parameters distribution near wall region has a distinct periodicity due to the rolling motion. The averaged deviation of the void fraction measured by the probe from that obtained from measured pressure drop is about 8%. (authors)

Top quark pair production cross-section measurements and measurements of $t\\bar{t}+X$ with the ATLAS and CMS detectors

CERN Document Server

Sidoti, Antonio; The ATLAS collaboration

2016-01-01

We present measurements of the inclusive and differential top-quark pair production cross sections in proton-proton collisions with the ATLAS and CMS detector at the LHC. Measurements have been performed at a center of mass energy of 8 TeV and 13 TeV. The inclusive measurements reach high precision and are compared to the best available theoretical calculations. Differential measurements of the kinematic properties of top quark pair production are also discussed. The production of top-quark pairs in association with W and Z bosons is also presented. These processes are important backgrounds to searches for new physics and are all compared to the best available theoretical calculations.

Modeling a Sustainable Salt Tolerant Grass-Livestock Production System under Saline Conditions in the Western San Joaquin Valley of California

Directory of Open Access Journals (Sweden)

Stephen R. Kaffka

2013-09-01

Full Text Available Salinity and trace mineral accumulation threaten the sustainability of crop production in many semi-arid parts of the world, including California’s western San Joaquin Valley (WSJV. We used data from a multi-year field-scale trial in Kings County and related container trials to simulate a forage-grazing system under saline conditions. The model uses rainfall and irrigation water amounts, irrigation water quality, soil, plant, and atmospheric variables to predict Bermuda grass (Cynodon dactylon (L. Pers. growth, quality, and use by cattle. Simulations based on field measurements and a related container study indicate that although soil chemical composition is affected by irrigation water quality, irrigation timing and frequency can be used to mitigate salt and trace mineral accumulation. Bermuda grass yields of up to 12 Mg dry matter (DM·ha−1 were observed at the field site and predicted by the model. Forage yield and quality supports un-supplemented cattle stocking rates of 1.0 to 1.2 animal units (AU·ha−1. However, a balance must be achieved between stocking rate, desired average daily gain, accumulation of salts in the soil profile, and potential pollution of ground water from drainage and leaching. Using available weather data, crop-specific parameter values and field scale measurements of soil salinity and nitrogen levels, the model can be used by farmers growing forages on saline soils elsewhere, to sustain forage and livestock production under similarly marginal conditions.

Innovative Equipment and Production Method for Mixed Fodder in the Conditions of Agricultural Enterprises

Science.gov (United States)

Sabiev, U. K.; Demchuk, E. V.; Myalo, V. V.; Soyunov, A. S.

2017-07-01

It is recommended to feed the cattle and poultry with grain fodder in the form of feed mixture balanced according to the content. Feeding of grain fodder in the form of stock feed is inefficient and economically unreasonable. The article is devoted to actual problem - the preparation of mixed fodder in the conditions of agricultural enterprises. Review and critical analyses of mixed fodder assemblies and aggregates are given. Structural and technical schemes of small-size mixed fodder aggregate with intensified attachments of vibrating and percussive action for preparation of bulk feed mixture in the conditions of agricultural enterprises were developed. The mixed fodder aggregate for its preparation in the places of direct consumption from own grain fodder production and purchased protein and vitamin supplements is also suggested. Mixed fodder aggregate allows to get prepared mixed fodder of high uniformity at low cost of energy and price of production that is becoming profitable for livestock breeding. Model line-up of suggested mixed fodder aggregate with different productivity both for small and big agricultural enterprises is considered.

Effect of redox conditions on bacterial and fungal biomass and carbon dioxide production in Louisiana coastal swamp forest sediment

International Nuclear Information System (INIS)

Seo, Dong Cheol; DeLaune, Ronald D.

2010-01-01

Fungal and bacterial carbon dioxide (CO 2 ) production/emission was determined under a range of redox conditions in sediment from a Louisiana swamp forest used for wastewater treatment. Sediment was incubated in microcosms at 6 Eh levels (-200, -100, 0, + 100, + 250 and + 400 mV) covering the anaerobic range found in wetland soil and sediment. Carbon dioxide production was determined by the substrate-induced respiration (SIR) inhibition method. Cycloheximide (C 15 H 23 NO 4 ) was used as the fungal inhibitor and streptomycin (C 21 H 39 N 7 O 12 ) as the bacterial inhibitor. Under moderately reducing conditions (Eh > + 250 mV), fungi contributed more than bacteria to the CO 2 production. Under highly reducing conditions (Eh ≤ 0 mV), bacteria contributed more than fungi to the total CO 2 production. The fungi/bacteria (F/B) ratios varied between 0.71-1.16 for microbial biomass C, and 0.54-0.94 for microbial biomass N. Under moderately reducing conditions (Eh ≥ + 100 mV), the F/B ratios for microbial biomass C and N were higher than that for highly reducing conditions (Eh ≤ 0 mV). In moderately reducing conditions (Eh ≥ + 100 mV), the C/N microbial biomass ratio for fungi (C/N: 13.54-14.26) was slightly higher than for bacteria (C/N: 9.61-12.07). Under highly reducing redox conditions (Eh ≤ 0 mV), the C/N microbial biomass ratio for fungi (C/N: 10.79-12.41) was higher than for bacteria (C/N: 8.21-9.14). For bacteria and fungi, the C/N microbial biomass ratios under moderately reducing conditions were higher than that in highly reducing conditions. Fungal CO 2 production from swamp forest could be of greater ecological significance under moderately reducing sediment conditions contributing to the greenhouse effect (GHE) and the global warming potential (GWP). However, increases in coastal submergence associated with global sea level rise and resultant decrease in sediment redox potential from increased flooding would likely shift CO 2 production to bacteria

Plant community, primary productivity, and environmental conditions following wetland re-establishment in the Sacramento-San Joaquin Delta, California

Science.gov (United States)

Miller, R.L.; Fujii, R.

2010-01-01

Wetland restoration can mitigate aerobic decomposition of subsided organic soils, as well as re-establish conditions favorable for carbon storage. Rates of carbon storage result from the balance of inputs and losses, both of which are affected by wetland hydrology. We followed the effect of water depth (25 and 55 cm) on the plant community, primary production, and changes in two re-established wetlands in the Sacramento San-Joaquin River Delta, California for 9 years after flooding to determine how relatively small differences in water depth affect carbon storage rates over time. To estimate annual carbon inputs, plant species cover, standing above- and below-ground plant biomass, and annual biomass turnover rates were measured, and allometric biomass models for Schoenoplectus (Scirpus) acutus and Typha spp., the emergent marsh dominants, were developed. As the wetlands developed, environmental factors, including water temperature, depth, and pH were measured. Emergent marsh vegetation colonized the shallow wetland more rapidly than the deeper wetland. This is important to potential carbon storage because emergent marsh vegetation is more productive, and less labile, than submerged and floating vegetation. Primary production of emergent marsh vegetation ranged from 1.3 to 3.2 kg of carbon per square meter annually; and, mid-season standing live biomass represented about half of the annual primary production. Changes in species composition occurred in both submerged and emergent plant communities as the wetlands matured. Water depth, temperature, and pH were lower in areas with emergent marsh vegetation compared to submerged vegetation, all of which, in turn, can affect carbon cycling and storage rates. ?? Springer Science+Business Media B.V. 2009.

Optimization of culture conditions for gamma-aminobutyric acid production in fermented adzuki bean milk

Directory of Open Access Journals (Sweden)

Hung Yi Song

2018-01-01

Full Text Available γ-Aminobutyric acid (GABA, a nonprotein amino acid, is widely distributed in nature and fulfills several physiological functions. In this study, various lactic acid strains commonly used to produce fermented milk products were inoculated into adzuki bean milk for producing GABA. The high GABA producing strain was selected in further experiment to improve the GABA production utilizing culture medium optimization. The results demonstrated that adzuki bean milk inoculated with Lactobacillus rhamnosus GG increased GABA content from 0.05 mg/mL to 0.44 mg/mL after 36 hours of fermentation, which showed the greatest elevation in this study. Furthermore, the optimal cultural condition to adzuki bean milk inoculated with L. rhamnosus GG to improve the GABA content was performed using response surface methodology. The results showed that GABA content was dependent on the addition of galactose, monosodium glutamate, and pyridoxine with which the increasing ratios of GABA were 23–38%, 24–68%, and 8–36%, respectively. The optimal culture condition for GABA production of adzuki bean milk was found at the content of 1.44% galactose, 2.27% monosodium glutamate, and 0.20% pyridoxine. Under the optimal cultural condition, the amount of GABA produced in the fermented adzuki bean milk was 1.12 mg/mL, which was 22.4-fold higher than that of the unfermented adzuki bean milk (0.05 mg/100 mL. The results suggested that the optimized cultural condition of adzuki bean milk inoculated with L. rhamnosus GG can increase GABA content for consumers as a daily supplement as suggested.

Measurement of plasma production and neutralization in gas neutralizers

International Nuclear Information System (INIS)

Maor, D.; Meron, M.; Johnson, B.; Jones, K.; Agagu, A.; Hu, B.

1986-01-01

In order to satisfy the need of experimental data for the designing of gas neutralizers we have started a project aimed at measuring all relevant cross sections for the charge exchange of H - , H 0 and H + projectiles, as well as the cross sections for the production of ions in the target. The expected results of these latter measurements are shown schematically

Characterization of Adipose Tissue Product Quality Using Measurements of Oxygen Consumption Rate.

Science.gov (United States)

Suszynski, Thomas M; Sieber, David A; Mueller, Kathryn; Van Beek, Allen L; Cunningham, Bruce L; Kenkel, Jeffrey M

2018-03-14

Fat grafting is a common procedure in plastic surgery but associated with unpredictable graft retention. Adipose tissue (AT) "product" quality is affected by the methods used for harvest, processing and transfer, which vary widely amongst surgeons. Currently, there is no method available to accurately assess the quality of AT. In this study, we present a novel method for the assessment of AT product quality through direct measurements of oxygen consumption rate (OCR). OCR has exhibited potential in predicting outcomes following pancreatic islet transplant. Our study aim was to reapportion existing technology for its use with AT preparations and to confirm that these measurements are feasible. OCR was successfully measured for en bloc and postprocessed AT using a stirred microchamber system. OCR was then normalized to DNA content (OCR/DNA), which represents the AT product quality. Mean (±SE) OCR/DNA values for fresh en bloc and post-processed AT were 149.8 (± 9.1) and 61.1 (± 6.1) nmol/min/mg DNA, respectively. These preliminary data suggest that: (1) OCR and OCR/DNA measurements of AT harvested using conventional protocol are feasible; and (2) standard AT processing results in a decrease in overall AT product quality. OCR measurements of AT using existing technology can be done and enables accurate, real-time, quantitative assessment of the quality of AT product prior to transfer. The availability and further validation of this type of assay could enable optimization of fat grafting protocol by providing a tool for the more detailed study of procedural variables that affect AT product quality.

Pressure retarded osmosis for energy production: membrane materials and operating conditions.

Science.gov (United States)

Kim, H; Choi, J-S; Lee, S

2012-01-01

Pressure retarded osmosis (PRO) is a novel membrane process to produce energy. PRO has the potential to convert the osmotic pressure difference between fresh water (i.e. river water) and seawater to electricity. Moreover, it can recover energy from highly concentrated brine in seawater desalination. Nevertheless, relatively little research has been undertaken for fundamental understanding of the PRO process. In this study, the characteristics of the PRO process were examined using a proof-of-concept device. Forward osmosis (FO), reverse osmosis (RO), and nanofiltration (NF) membranes were compared in terms of flux rate and concentration polarization ratio. The results indicated that the theoretical energy production by PRO depends on the membrane type as well as operating conditions (i.e. back pressure). The FO membrane had the highest energy efficiency while the NF membrane had the lowest efficiency. However, the energy production rate was low due to high internal concentration polarization (ICP) in the PRO membrane. This finding suggests that the control of the ICP is essential for practical application of PRO for energy production.

Eddy correlation measurements in wet environmental conditions

Science.gov (United States)

Cuenca, R. H.; Migliori, L.; O Kane, J. P.

2003-04-01

The lower Feale catchment is a low-lying peaty area of 200 km^2 situated in southwest Ireland that is subject to inundation by flooding. The catchment lies adjacent to the Feale River and is subject to tidal signals as well as runoff processes. Various mitigation strategies are being investigated to reduce the damage due to flooding. Part of the effort has required development of a detailed hydrologic balance for the study area which is a wet pasture environment with local field drains that are typically flooded. An eddy correlation system was installed in the summer of 2002 to measure components of the energy balance, including evapotranspiration, along with special sensors to measure other hydrologic variables particular to this study. Data collected will be essential for validation of surface flux models to be developed for this site. Data filtering is performed using a combination of software developed by the Boundary-Layer Group (BLG) at Oregon State University together with modifications made to this system for conditions at this site. This automated procedure greatly reduces the tedious inspection of individual records. The package of tests, developed by the BLG for both tower and aircraft high frequency data, checks for electronic spiking, signal dropout, unrealistic magnitudes, extreme higher moment statistics, as well as other error scenarios not covered by the instrumentation diagnostics built into the system. Critical parameter values for each potential error were developed by applying the tests to real fast response turbulent time series. Potential instrumentation problems, flux sampling problems, and unusual physical situations records are flagged for removal or further analysis. A final visual inspection step is required to minimize rejection of physically unusual but real behavior in the time series. The problems of data management, data quality control, individual instrumentation sensitivity, potential underestimation of latent and sensible heat

Measuring and managing radiologist productivity, part 1: clinical metrics and benchmarks.

Science.gov (United States)

Duszak, Richard; Muroff, Lawrence R

2010-06-01

Physician productivity disparities are not uncommonly debated within radiology groups, sometimes in a contentious manner. Attempts to measure productivity, identify and motivate outliers, and develop equitable management policies can present challenges to private and academic practices alike but are often necessary for a variety of professional, financial, and personnel reasons. This is the first of a two-part series that will detail metrics for evaluating radiologist productivity and review published benchmarks, focusing primarily on clinical work. Issues and limitations that may prevent successful implementation of measurement systems are explored. Part 2 will expand that discussion to evaluating nonclinical administrative and academic activities, outlining advantages and disadvantages of addressing differential productivity, and introducing potential models for practices seeking to motivate physicians on the basis of both clinical and nonclinical work.

Evidence for WZ Production and a Measurement of the WZ Production Cross Section

Energy Technology Data Exchange (ETDEWEB)

Degenhardt, James D. [Univ. of Michigan, Ann Arbor, MI (United States)

2007-05-01

This dissertation describes a test of the Standard Model (SM) of particle physics by measuring the probability, or cross section, of simultaneously producing a W boson and a Z boson from proton-antiproton collisions. The SM predicts the cross section of WZ production to be 3.68 ± 0.25 pb. The SM and physics of WZ production are described in Chapter 2 of this dissertation. The 1.96 TeV center-of-mass energy proton-antiproton collisions are provided by the Fermi National Accelerator Laboratory (FNAL) Tevatron Collider. The W and Z particles are detected using the D0 detector, which is described in Chapter 3. The data were collected by the detector during 2002-2006 corresponding to 1 fb^-1 of p{bar p} collisions. This data set is described in Chapter 6. The measurement uses the trilepton (evee, μvee, evμμ, and μvμμ) decay channels, in which a W decays to a charged lepton plus a neutrino and a Z decays to a pair of charged leptons. The W and Z particle selection criteria, detection efficiency, and background determination are described in Chapter 7. We observe 13 candidate events in 1 fb^-1 of p$\\bar{p}$ collisions. In this data set we expect to see 4.5 ± 0.6 background events, and we expect to see 9.2 ± 1.0 signal events. The probability of 4.5 ± 0.6 background events to fluctuate to 13 or more events is 1.2 x 10^-3 which is a 3.0 σ deviation from the background estimate. A log likelihood method is used to determine the most likely cross section as determined by the measured signal efficiencies, the expected backgrounds, and the observed data. Presented in Chapter 8 is a measurement of the cross section for p$\\bar{p}$ → WZ + X at √s = 1.96 TeV. The WZ diboson production cross section is measured to be σ_WZ = 2.7$+1.7\\atop{-1.3}$ pb. This is in agreement with the predicted Standard Model cross section.

ATLAS reach for Quarkonium production and polarization measurements

CERN Document Server

Etzion, Erez; 8th International Conference on Hyperons, Charm and Beauty Hadrons

2009-01-01

The ATLAS detector at CERN's LHC is preparing to take data from the first proton-proton collisions expected in the next few months. We report on the analysis of simulated data samples for production of heavy Quarkonium states J/psi and Upsilon, corresponding to an integrated luminosity of 10 pb^-1 with center of mass energy of 14 TeV expected at the early ATLAS data. We review various aspects of prompt Quarkonium production at LHC: the accessible ranges in transverse momentum and pseudorapidity, spin alignment of vector states, separation of color octet and color singlet production mechanism and feasibility of observing radiative decays Xi_c and Xi_b decays. Strategies of various measurements are outlined and methods of separating promptly produced J/psi and Upsilon mesons from various backgrounds are discussed.

The measurement of interplanetary scintillations in conditions of strong radio interference

International Nuclear Information System (INIS)

Duffett-Smith, P.J.

1980-01-01

Observations of interplanetary scintillations (IPS) are often severely limited by interference from man-made transmissions within the receiver pass-band. A new method of measuring IPS is described which can give useful data even in conditions of bad interference. (author)

Fast freeze-drying cycle design and optimization using a PAT based on the measurement of product temperature.

Science.gov (United States)

Bosca, Serena; Barresi, Antonello A; Fissore, Davide

2013-10-01

This paper is focused on the use of an innovative Process Analytical Technology for the fast design and optimization of freeze-drying cycles for pharmaceuticals. The tool is based on a soft-sensor, a device that uses the experimental measure of product temperature during freeze-drying, a mathematical model of the process, and the Extended Kalman Filter algorithm to estimate the sublimation flux, the residual amount of ice in the vial, and some model parameters (heat and mass transfer coefficients). The accuracy of the estimations provided by the soft-sensor has been shown using as test case aqueous solutions containing different excipients (sucrose, polyvinylpyrrolidone), processed at various operating conditions, pointing out that the soft-sensor allows a fast estimation of model parameters and product dynamics without involving expensive hardware or time consuming analysis. The possibility of using the soft-sensor to calculate in-line (or off-line) the design space of the primary drying phase is here presented and discussed. Results evidences that by this way, it is possible to identify the values of the heating fluid temperature that maintain product temperature below the limit value, as well as the operating conditions that maximize the sublimation flux. Various experiments have been carried out to test the effectiveness of the proposed approach for a fast design of the cycle, evidencing that drying time can be significantly reduced, without impairing product quality. Copyright © 2013 Elsevier B.V. All rights reserved.

Methods for measuring of fuel can deformation under radiation conditions

International Nuclear Information System (INIS)

Zelenchuk, A.V.; Fetisov, B.V.; Lakin, Yu.G.; Tonkov, V.Yu.

1978-01-01

The possibility for measuring fuel can deformation under radiation conditions by means of the acoustic method and tensoresistors is considered. The construction and operation of the in-pile facility for measuring creep of the fuel can specimen loaded by the internal pressure is described. The data on neutron radiation effect on changes in creep rate for zirconium fuel can are presented. The results obtained with tensoresistors are in a good agreement with those obtained by the acoustic method, which enables to recommend the use of both methods for the irradiation creep investigation of the fuel element cans

Standardization of test conditions for gamma camera performance measurement

International Nuclear Information System (INIS)

Jordan, K.

1982-02-01

The way of measuring gamma camera performance is to use point sources or flood sources in air, often in combination with bar phantoms. This method has nothing in common with the use of a camera in clinical practice. Particularly in the case of low energy emitters, like Tc-99m, the influence of scattered radiation over the performance of cameras is very high. The IEC document 'Characteristics and test conditions of radionuclide imaging devices' is discussed

PRODUCTIVITY OF MICROALGAE CHLORELLA VULGARIS IN LABORATORY CONDITION

Directory of Open Access Journals (Sweden)

Agnieszka Patyna

2017-06-01

Full Text Available Algae biomass is increasingly regarded as a potential resource that could be used to produce biofuels, electricity and heat. Algae contain a lot of nutrients, so they can be used as food for humans and livestock. Because of their valuable composition (many nutrients they are used as supplements of balanced diet, in turn taking into account their biosorption abbility they are used to detoxification of human body. Algae cultivation does not demand large areas of land to expose cells to sunlight, so their production rate is higher than vascular plants. Moreover algae cultivation lets to achieve high biomass concentration. Important cultivation factors are: illumination (light intensity is an important factor because it drives photosynthesis, CO2 supply, culture medium and mixing. The experimental research was conducted using Chlorella vulgaris BA 002 strain. The aim of this study was to determine the effectiveness of biomass growth in laboratory condition.

Measurement of open beauty production at HERA in the D*μ final state

International Nuclear Information System (INIS)

Chekanov, S.; Derrick, M.; Magill, S.

2006-09-01

The production of beauty quarks with a D *± and a muon in the final state has been measured with the ZEUS detector at HERA using an integrated luminosity of 114 pb -1 . Low transverse-momentum thresholds for the muon and D * meson allow a measurement of beauty production closer to the production threshold than previous measurements. The beauty signal was extracted using the charge correlations and angular distributions of the muon with respect to the D * meson. Cross sections for photoproduction and deep inelastic scattering are somewhat higher than, but compatible with, next-to-leading-order QCD predictions, and compatible with other measurements. (orig.)

Poly(3-hydroxybutyrate) production in an integrated electromicrobial setup: Investigation under stress-inducing conditions

KAUST Repository

Al Rowaihi, Israa Salem; Paillier, Alexis; Rasul, Shahid; Karan, Ram; Grö tzinger, Stefan Wolfgang; Takanabe, Kazuhiro; Eppinger, Jö rg

2018-01-01

extorquens AM1 and Cupriavidus necator H16. This setup allows to investigate the influence of different stress conditions, such as coexisting electrolysis, relatively high salinity, nutrient limitation, and starvation, on the production of PHB. The overall

Top quark pair production measurements using the ATLAS detector at the LHC

CERN Document Server

Yamauchi, Katsuya; The ATLAS collaboration

2015-01-01

Measurements of the inclusive top quark pair production cross sections in proton-proton collisions with the ATLAS detector at the Large Hadron Collider are presented. The most precise result requires opposite sign electrons and muons and uses the full data-set at a centre-of-mass energy of 7 and 8 TeV. In addition, differential measurements of the top transverse momentum and kinematic properties of the top-anti-top pair are discussed. These measurements, including results using boosted tops, probe our understanding of top pair production in the TeV regime. The results, unfolded to particle and parton level, are compared to recent Monte Carlo generators implementing LO and NLO matrix elements matched with parton showers and NLO QCD calculations. In addition, measurements of the production of top quark pairs in association with gauge bosons or jets are presented.

β-cell serotonin production is associated with female sex, old age, and diabetes-free condition.

Science.gov (United States)

Kim, Yeong Gi; Moon, Joon Ho; Kim, Kyuho; Kim, Hyeongseok; Kim, Juok; Jeong, Ji-Seon; Lee, Junguee; Kang, Shinae; Park, Joon Seong; Kim, Hail

2017-11-25

Serotonin is known to be present in pancreatic β-cells and to play several physiological roles, including insulin secretion, β-cell proliferation, and paracrine inhibition of α-cells. However, the serotonin production of different cell lines and islets has not been compared based on age, sex, and diabetes related conditions. Here, we directly compared the serotonin concentrations in βTC and MIN6 cell lines, as well as in islets from mice using ultra-performance liquid chromatography tandem mass spectrometry. The average serotonin concentration was 5-10 ng/mg protein in the islets of male and non-pregnant female mice. The serotonin level was higher in females than males at 8 weeks, although there was no difference at 1 year. Furthermore, we observed serotonin by immunofluorescence staining in the pancreatic tissues of mice and human. Serotonin was detected by immunofluorescence staining in a portion of β-cells from islets of old female mice, but not of male or young female mice. A similar pattern was observed in human pancreas as well. In humans, serotonin production in β-cells was associated with a diabetes-free condition. Thus, serotonin production in β-cells was associated with old age, female sex, and diabetes-free condition. Copyright © 2017 Elsevier Inc. All rights reserved.

Measurement of Single-top t-channel Production Using ATLAS Data

CERN Document Server

Holzbauer, Jenny; Schwienhorst, R; Repko, W; Lapidus, L; Pratt, S

2012-01-01

This document reports the measurement of the single-top t-channel cross-section using data from the ATLAS detector, located at the Large Hadron Collider on the border of France and Switzerland. The data used were collected during the first half of 2011, from proton-proton collisions with a 7 TeV center-of-mass collision energy. Single-top is electroweak top-quark production and t-channel is one of the standard model production modes. To isolate this production, selections are applied to find events with a similar final state. A cut-based analysis is used to further isolate the signal using a series of selections in several orthogonal kinematic regions. Finally, a statistical analysis is performed to determine the measured cross-section and the CKM matrix element |Vtb|. The cross-section for top and anti-top production is considered separately and the resulting cross-sections are σ t+ = 59 +18 -16 pb for the positive charge channel and σ t- = 33 +13 -12 pb for the negative charge chan...

Optimization of the growth conditions for amylase production by bacillus licheniformis 208 isolated from local hotsprings of karachi

International Nuclear Information System (INIS)

Asad, W.; Saleem, F.; Ajaz, M.; Rasool, S.A.

2014-01-01

Studies on the optimum conditions for the production of extracellular amylase were carried out with a newly isolated strain of Bacillus 208 from the hotsprings in Karachi. The optimum temperature, initial medium pH and incubation period for amylase production were 50 degree C, 7.0 and 24 hrs respectively. Furthermore, cells when grown in the complex media showed high amylase production compared to the minimal medium. Effect of different carbon sources revealed that soluble starch (1%) increased the amylase yield significantly. Peptone (as nitrogen source) gave higher yield as compared to other nitrogen sources tested. Under optimized conditions, the organism entered the stationary phase after 12 hrs and amylase production was observed to be maximum at 24th hrs of cultivation. Enzyme production regulation is influenced by catabolite repression. Reduction in enzyme production was observed in the presence of EDTA while addition of tween 20 and CaCl/sub 2/ helped to enhance the enzyme production. (author)

Cellulase production by Trichoderma harzianum in static and mixed solid-state fermentation reactors under nonaseptic conditions

Energy Technology Data Exchange (ETDEWEB)

Deschamps, F.; Giuliano, C.; Asther, M.; Huet, M.C.; Roussos, S.

1985-09-01

Cellulase production from lignocellulosic materials was studied in solid-state cultivation by both static and mixed techniques under nonaseptic conditions. The effects of fermentation conditions, such as moisture content, pH, temperature, and aeration, on cellulase production by Trichoderma harzianum using a mixture of wheat straw (80%) and bran (20%) were investigated. With a moisture content of 74% and a pH of 5.8, 18 IU filter paper activity and 198 IU endoglucanase activity/g initial substrate content were obtained in 66 hours. The extension from static column cultivation to stirred tank reactor of 65 l capacity gave similar yields of cellulase.

Optimization of simultaneous saccharification and fermentation conditions with amphipathic lignin derivatives for concentrated bioethanol production.

Science.gov (United States)

Cheng, Ningning; Koda, Keiichi; Tamai, Yutaka; Yamamoto, Yoko; Takasuka, Taichi E; Uraki, Yasumitsu

2017-05-01

Amphipathic lignin derivatives (A-LDs) prepared from the black liquor of soda pulping of Japanese cedar are strong accelerators for bioethanol production under a fed-batch simultaneous enzymatic saccharification and fermentation (SSF) process. To improve the bioethanol production concentration, conditions such as reaction temperature, stirring program, and A-LDs loadings were optimized in both small scale and large scale fed-batch SSF. The fed-batch SSF in the presence of 3.0g/L A-LDs at 38°C gave the maximum ethanol production and a high enzyme recovery rate. Furthermore, a jar-fermenter equipped with a powerful mechanical stirrer was designed for 1.5L-scale fed-batch SSF to achieve rigorous mixing during high substrate loading. Finally, the 1.5L fed-batch SSF with a substrate loading of 30% (w/v) produced a high ethanol concentration of 87.9g/L in the presence of A-LDs under optimized conditions. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

Population ecology of the mallard: II. Breeding habitat conditions, size of the breeding populations, and production indices

Science.gov (United States)

Pospahala, Richard S.; Anderson, David R.; Henny, Charles J.

1974-01-01

production from the July Production Survey were studied in detail. Several indices relating to production showed marked declines from west to east in the Prairie-Parkland Area, these are: (1) density of breeding mallards (per square mile and per May pond), (2) brood density (per square mile and per July pond), (3) average brood size (all species combined), and (4) brood survival from class II to class III. An index to late nesting and renesting efforts was highest during years when midsummer water conditions were good. Production rates of many ducks breeding in North America appear to be regulated by both density-dependent and density-independent factors. Spacing of birds in the Prairie-Parkland Area appeared to be a key factor in the density-dependent regulation of the population. The spacing mechanism, in conjunction with habitat conditions, influenced some birds to overfly the primary breeding grounds into less favorable habitats to the north and northwest where the production rate may be suppressed. The production rate of waterfowl in the Prairie Parkland Area seems to be independent of density (after emigration has taken place) because the production index appears to be a linear function of the number of breeding birds in the area. Similarly, the production rate of waterfowl in northern Saskatchewan and northern Manitoba appeared to be independent of density. Production indices in these northern areas appear to be a linear function of the size of the breeding population. Thus, the density and distribution of breeding ducks is probably regulated through a spacing mechanism that is at least partially dependent on measurable environmental factors. The result is a density-dependent process operating to ultimately effect the production and production rate of breeding ducks on a continent-wide basis. Continental production, and therefore the size of the fall population, is probably partially regulated by the number of birds that are distributed north and northwest into