Effects of acid conditions on element distribution beneath a sulphur basepad

International Nuclear Information System (INIS)

Sevigny, J.H.; Fennell, J.W.; Sharma, A.

1997-04-01

A reconnaissance-scale study was conducted to determine the extent of acid conditions beneath a sulphur basepad at Canadian Occidental's Balzac sour gas plant and to examine the effects of acid conditions on element distribution in the subsurface. Sulphur which is extracted from sour natural gas is stored in large blocks directly on the ground. The elemental sulphur will oxidize to H 2 SO 4 under aerobic conditions and with the proper microorganisms can result in possible removal of metals from the soil and transportation in the groundwater. The basepad at the sour gas plant is 36 years old and is covered by about 1 metre of elemental sulphur. EM31 terrain conductivity and electrical resistivity tomography geophysical surveys were conducted to determine aerial and subsurface bulk electrical conductivity. The objective was to locate the indurated layer using the geophysical techniques and soil boring. The extent of acid conditions beneath the sulphur block was determined. Migration rates for the site were also estimated. Results suggested that minimal soil and groundwater impact can be expected from sulphur blocks overlying properly buffered soils, and that synthetic liners beneath sulphur blocks may not be a necessary measure at sour gas plants in Alberta. 19 refs., 6 tabs., 6 figs., 5 appendices

Anion-exchange Studies of Radioactive Trace Elements in Sulphuric Acid Solutions

Energy Technology Data Exchange (ETDEWEB)

Samsahl, K

1963-01-15

As part of a chemical group separation procedure used as a pretreatment in gamma spectrometric analysis, a study has been made of the adsorption from sulphuric acid solutions on strongly basic anion exchange resins, prepared in the hydroxide and the sulphate forms, of trace activities of Na, P, K, Ca, Sc, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Rb, Sr, Zr, Nb, Mo, Tc, Ag, Cd, In, Cs, Ba, La, Ce, Hf, Ta, W, Ir, Pa and Np. Besides adsorbing some of the trace elements in the solution, the anion exchange resin in the hydroxide form will neutralize the bulk of the sulphuric acid. This makes possible the subsequent sequential separation of chloride complexes on short anion-exchange columns by a stepwise increasing of the HCl concentration of the solution. On the basis of the results obtained in the present and earlier experiments, a new improved chemical group-separation procedure for mixtures of radioactive trace elements is outlined.

SULPHUR-CONTAINING AMINO ACIDS METABOLISM IN EXPERIMENTAL HYPER- AND HYPOTHYROIDISM IN RATS.

Science.gov (United States)

Nechiporuk, V; Zaichko, N; Korda, М; Melnyk, A; Koloshko, O

2017-10-01

Hyper- and hypothyroidism are some of the most common endocrinopathies that cause many metabolic disorders including amino acids metabolism. However, a specific molecular mechanism of thyroid hormones influence on sulphur-containing amino acids metabolism has not been established. The aim of our research was to investigate experimentally the influence of thyroid gland functional state on the main enzymatic systems of sulphur-containing amino acids metabolism in liver and kidneys, the content of homocysteine, cysteine and H2S in blood. The rats were administered with L-thyroxine and mercazolil to simulate the states of hyper- and hypothyroidism, which were confirmed by the content of fT3, fT4 and TSH in the blood. In liver and kidneys of the animals with hypothyroidism we observed the decrease in the activity of enzymes of remethylation cycle of S-adenosylmethioninsyntase, S-adenosylhomocysteinhyhdrolase, betaine-homocysteine methyltransferase. Suppression of transsulfuration transformation of homocysteine to cysteine in hypothyroidism was mainly due to the inhibition of cystathionine synthase activity of cystathionine-β-synthase, wherein cystathionase activity of cystathionine-γ-lyase was not changed. In animals with hypothyroidism we also noticed the inhibition of cysteine desulfunation reactions: the activity of enzymes of cystathionine-β-synthase, cystathionine-γ-lyase and cysteine aminotransferase significantly decreased in liver and kidneys. Experimental hyperthyroidism was accompanied by increase in activity of remethylation cycle enzymes, increase in cystationine synthase activity of cystathionine-β-synthase in liver and activity of these enzymes in kidneys. The simulation of hyperthyroidism led to the decrease of homocysteine concentration, and of hypothyroidism - to the increase of homocysteine and cysteine concentrations and reduced H2S content in blood of the animals. Thus, the significant risk factors for the development of atherosclerosis

Total mineral material, acidity, sulphur, and nitrogen in rain and snow at Kentville, Nova Scotia

Energy Technology Data Exchange (ETDEWEB)

Herman, F A; Gorham, E

1957-01-01

Analyses of total ash, sulphur, ph, ammonia, and nitrate nitrogen have been made on 23 monthly precipitation samples and 17 individual snow samples collected between June 1952 and May 1954 at Kentville, Nova Scotia, in a predominantly agricultural area. Mean annual supply of total mineral ash was 95 kg/ha, of sulphur 9.1 hg/ha, of ammonia nitrogen 2.8 kg/ha, and of nitrate nitrogen 1.1 kg/ha. Average pH was 5.7, and rains more acid than this exhibited higher levels of both nitrate and sulphur, and a marked correlation between the latter and ammonia. Snow samples had much lower concentrations of ash, sulphur, and nitrogen than rain samples collected in the same months, which may perhaps indicate a lower efficiency of snow flakes in removing materials from the atmosphere.

The non-participation of organic sulphur in acid mine drainage generation.

Science.gov (United States)

Casagrande, D J; Finkelman, R B; Caruccio, F T

1989-12-01

Acid mine drainage is commonly associated with land disturbances that encounter and expose iron sulphides to oxidising atmospheric conditions. The attendant acidic conditions solubilise a host of trace metals. Within this flow regime the potential exists to contaminate surface drinking water supplies with a variety of trace materials. Accordingly, in evaluating the applications for mines located in the headwaters of water sheds, the pre-mining prediction of the occurrence of acid mine drainage is of paramount importance.There is general agreement among investigators that coal organic sulphur is a nonparticipant in acid mine drainage generation; however, there is no scientific documentation to support this concensus. Using simulated weathering, kinetic, mass balance, petrographic analysis and a peroxide oxidation procedure, coal organic sulphur is shown to be a nonparticipant in acid mine drainage generation. Calculations for assessing the acid-generating potential of a sedimentary rock should not include organic sulphur content.

Ethanol and biogas production after steam pretreatment of corn stover with or without the addition of sulphuric acid

Directory of Open Access Journals (Sweden)

Bondesson Pia-Maria

2013-01-01

which the slurry from the pretreatment was divided into a solid fraction and a liquid fraction. The solid fraction was subjected to SSF, while the liquid fraction, together with the filtered residual from SSF, was used in AD. Using sulphuric acid in AD did not inhibit the reaction, which may be due to the low concentration of sulphuric acid used. In contrast, a pretreatment step without sulphuric acid resulted not only in higher concentrations of inhibitors, which affected the ethanol yield, but also in lower methane production.

Electrolytes for methanol-air fuel cells. I. The performance of methanol electro-oxidation catalysts in sulphuric acid and phosphoric acid electrolytes

Energy Technology Data Exchange (ETDEWEB)

Andrew, M.R.; McNicol, B.D.; Short, R.T.; Drury, J.S.

1977-03-01

Phosphoric acid and sulphuric acid have been compared as potential electrolytes for methanol-air fuel cells. The performances of typical electro-oxidation catalysts were measured in both electrolytes over a range of concentrations. With all catalysts the activity falls with increasing acid concentration. While this is to some extent due to the decrease in water activity at higher concentrations it seems that with both acids there is significant poisoning of the catalyst. The results can be explained for both electrolytes by assuming that adsorption of undissociated acid poisons the catalyst surfaces and that the reaction rate on the poisoned surfaces is proportional to the water activity.

Effect of Schiff's Bases as Corrosion Inhibitors on Mild Steel in Sulphuric Acid

Directory of Open Access Journals (Sweden)

R. K. Upadhyay

2007-01-01

Full Text Available Mass loss and thermometric methods have been used to study the corrosion inhibitory effect of synthesised Schiff's bases viz. N-(furfurilidine – 4- methoxy aniline (SB1, N-(furfurilidine – 4- methylaniline (SB2, N-(salicylidine – 4- methoxy aniline (SB3, N-(cinnamalidine – 4 –methoxy aniline (SB4 and N-(cinnamalidine - 2-methylaniline (SB5 on mild steel in sulphuric acid solutions. Results show that both methods have good agreement with each other and inhibition efficiency depends upon the concentration of inhibitor as well as that of acid. Maximum inhibition efficiency is shown at highest concentration of Schiff's bases at the highest strength of acid.

Evaluation of the protein concentration in enzymes via the determination of sulphur by TXRF

International Nuclear Information System (INIS)

Mertens, M.; Rittmeyer, C.; Kolbesen, B.O.

2000-01-01

Total reflection x-ray fluorescence spectrometry (TXRF) offers many advantages for the identification of trace elements in biological samples like enzymes, tissues or plants. Without any preliminary treatment elements may be determined with high accuracy especially transition metals like Fe, Ni, Cu, Mo and the alkaline earth metal Ca. A further aspect of the investigation of enzymes is the simple and simultaneous determination of light elements. Especially sulphur is of interest. The element sulphur exists mainly in the two amino, acids methionine and cysteine as well as in iron-sulphur clusters and may be used for an easy and simultaneous calculation of the protein concentration. Hence the quantitative determination of sulphur by TXRF allows a cross-check regarding of the conventional quantitative determination of protein concentration by, for example, the Lowry method. On the basis of three enzymes of different origins and molecular weights the presentation will show the influence of the bio-organic matrix and different buffer media on element determination by TXRF. As is already known the influence of the matrix on the detection of light elements is stronger than on transition metals. It can be discussed whether layer thickness and layer effects of the drying residues (characterization by SEM and thickness profilometer (ALPHA-step)) and / or self absorption effects as well as the excitation are of significance. The results indicate that with enzymes of low molecular weight a reliable determination of sulphur is possible whereas those with higher molecular weights gave poorer results on account of the matrix effects described. (author)

Sulphur recirculation for reduced boiler corrosion; Minskad pannkorrosion med svavelrecirkulation

Energy Technology Data Exchange (ETDEWEB)

Andersson, Sven; Karlsson, Martin (Goetaverken Miljoe AB, Goeteborg (Sweden)); Blomqvist, Evalena; Baefver, Linda; Claesson, Frida; Davidsson, Kent (SP Sveriges Tekniska Forskningsinstitut, Boraas (Sweden)); Froitzheim, Jan; Pettersson, Jesper; Steenari, Britt-Marie (Chalmers Tekniska Hoegskola, Oorganisk miljoekemi, Goeteborg (Sweden))

2010-03-15

Sulphur recirculation is a new technology for reducing boiler corrosion and dioxin formation, which was demonstrated in full-scale tests performed at the Renova Waste to Energy plant at Saevenaes in Goeteborg (Sweden). Sulphur is recirculated from the flue gas cleaning back to the boiler, which reduces the chloride content of the deposits, which in turn reduces boiler corrosion and dioxin formation. Sulphur dioxide was separated from the flue gas in a wet scrubber by adding hydrogen peroxide, producing sulphuric acid. The sulphuric acid was injected into the furnace using nozzles with atomization air, surrounded by recirculated flue gas for improved mixing. By recirculating the sulphur, the sulphur dioxide concentration was increased in the boiler. Each sulphur atom passed the boiler several times and no external sulphur had to be added. Dioxin, ash, deposits and particle samplings together with 1000 h corrosion probe measurements were performed for normal operation (reference) and with sulphur recirculation respectively. During spring 2009, reference measurements were made and the recirculation system was installed and tested. During autumn 2009, a long term test with sulphur recirculation was made. An SO{sub 2} concentration of approximately 800 mg/m3 (n, d.g.) was maintained in the boiler by the system except during a period of extremely low sulphur content in the waste. The sulphur dioxide stack concentrations have been far below the emission limit. Sulphuric acid dew point measurements have shown that the sulphuric acid dosage did not lead to elevated SO{sub 3} concentrations, which may otherwise lead to low temperature corrosion. The chlorine content of both fly ash and boiler ash decreased and the sulphur content increased during the sulphur recirculation tests. The molar chlorine/sulphur ratio (Cl/S) decreased by two thirds in the fly ash as well as in the boiler ash, except for one sample. With sulphur recirculation in operation, the deposit growth was

Green approach to corrosion inhibition of mild steel in hydrochloric acid and sulphuric acid solutions by the extract of Murraya koenigii leaves

Energy Technology Data Exchange (ETDEWEB)

Quraishi, M.A., E-mail: maquraishi@rediffmail.com [Department of Applied Chemistry, Institute of Technology, Banaras Hindu University, Varanasi 221005 (India); Singh, Ambrish; Singh, Vinod Kumar [Udai Pratap Autonomous College, Varanasi 221002 (India); Yadav, Dileep Kumar; Singh, Ashish Kumar [Department of Applied Chemistry, Institute of Technology, Banaras Hindu University, Varanasi 221005 (India)

2010-07-01

The inhibition of the corrosion of mild steel in hydrochloric acid and sulphuric acid solutions by the extract of Murraya koenigii leaves has been studied using weight loss, electrochemical impedance spectroscopy (EIS), linear polarization and potentiodynamic polarization techniques. Inhibition was found to increase with increasing concentration of the leaves extract. The effect of temperature, immersion time and acid concentration on the corrosion behavior of mild steel in 1 M HCl and 0.5 M H{sub 2}SO{sub 4} with addition of extract was also studied. The inhibition was assumed to occur via adsorption of the inhibitor molecules on the metal surface. The adsorption of the extract on the mild steel surface obeys the Langmuir adsorption isotherm. The activation energy as well as other thermodynamic parameters (Q, {Delta}H*, and {Delta}S*) for the inhibition process was calculated. These thermodynamic parameters show strong interaction between inhibitor and mild steel surface. The results obtained show that the extract of the leaves of M. koenigii could serve as an effective inhibitor of the corrosion of mild steel in hydrochloric and sulphuric acid media.

Comparison of methods for the determination of reduced inorganic sulphur in acid sulphate soils

International Nuclear Information System (INIS)

Santomartino, S.L.

1999-01-01

Full text: The management of acid sulphate soils requires analytical methods that provide accurate data on the quantity of reduced inorganic sulphur within a soil, as it is this fraction that produces acid upon oxidation. This study uses sulphidic Coode Island Silt samples to compare common analytical methods including POCAS (Peroxide Oxidation-Combined Acidity and Sulphate) which consists of TSA (Total Sulphidic Acidity), S pos (Peroxide Oxidisable Sulphur), TOS (Total Oxidisable Sulphur) and chromium-reducible sulphur. The determination of total sulphur by Leco sulphur is strongly correlated with, but slightly less than, that analysed by XRF. Comparison of soil sulphide content by chromium-reducible sulphur, TSA and TOS methods indicates that TOS values are substantially higher than both other methods. The problem with the TOS method lies in the sulphate extraction procedure. Hot distilled water and HCI are commonly used as extractants, however hot distilled water fails to remove organic sulphur, thereby overestimating the sulphide content of the soil. Leco carbon analyses verify that a substantial proportion of organic matter exists within the samples. The HCI extraction process, which uses Ion Chromatography to analyse for sulphate, produces highly inaccurate results due to the interference of the sulphate peak by the chloride peak during analysis. An alternative method involving HCI extraction and XRF analysis of the soil residue is currently being undertaken. The use of KCI to extract sulphate generally produces values similar to the hot distilled water method. The sulphidic content measured by TSA is strongly correlated with, but slightly higher than that determined by the chromium-reducible sulphur method. This is attributed to the use of hydrogen peroxide in the TSA method, which oxidises organic matter to organic acids in addition to oxidising sulphides. These preliminary findings indicate that the chromium-reducible sulphur method is the most suitable

Accidental sulphuric acid poisoning in a newborn | Abdulkadir ...

African Journals Online (AJOL)

Accidental sulphuric acid poisoning in a newborn. I Abdulkadir, L Hassan, F Abdullahi, FD Akeredolu, S Purdue, M Okpe, AM Sobowale, OA Adewumi, U Abdullahi, MA Onadiran, TT Sholadoye, S Baba, WN Ogala ...

Sulphate sulphur concentration in vegetable crops, soil and ground water in the region affected by the sulphur dioxide emission from Plock oil refinery (central Poland)

International Nuclear Information System (INIS)

Mikula, W.

1995-01-01

Research was carried out in 1984-1990 in the region affected by the sulphur dioxide emission from one of the greatest oil refineries in Europe (Plock, central Poland). The sulphate sulphur concentration in the vegetable crops (red beet, carrot, parsley, bean, cabbage and dill), the soil and in ground water was defined in selected allotment gardens of Plock city and in a household garden located in the rural area about 25 km from the town. The highest amount of sulphur was found in the vegetable crops cultivated in the garden situated in the closest vicinity of the refinery. Sulphate sulphur contents harmful for plants (above 0.50 per cent d.m.) were noted in cabbage and carrot leaves in almost all the gardens (except one). The soil in all examined gardens was characterised by high sulphate sulphur concentration, which considerably exceeds the maximum amount admissible for light soil in Poland, i.e. 0.004 per cent d.m. The sulphate sulphur concentration in ground water in all the gardens exceeded the highest permissible content in drinking water in Poland. The sulphate sulphur content in the soil and ground water was not significantly dependent on the garden's distance from the refinery. Generally, the above normal sulphate sulphur concentrations occurred quite universally in the examined region and they concerned all the considered environmental components (vegetable crops, soil, ground water) and all the gardens. 22 refs., 6 tabs

Sulphur recovery and sulphur emissions at Alberta sour gas plants : annual report for 2005

International Nuclear Information System (INIS)

2005-01-01

The sulphur recovery of Alberta's grandfathered sour gas plants is monitored by the Alberta Energy and Utilities Board. This report provides an annual summary of industry performance for sulphur recovery at large acid gas flaring sour gas plants, and sulphur recovery at all acid gas injection sour gas plants. It follows Interim Directive (ID) 2001-3 which stipulates guidelines for sulphur recovery for the province of Alberta. It includes a list of grandfathered and non grandfathered plants in Alberta. Grandfathered sulphur recovery plants that exceed expectations have the option to file a sulphur emission performance credit report and can use the credits to meet some of their sulphur requirement in the future. Acid gas flaring plants face more stringent requirements and cannot earn credits. Several plants have degrandfathered in the past 5 years. Eleven have made upgrades, 4 have been relicensed to meet the requirements for new plants, and 4 have shut down. Forty-one grandfathered plants remain. Sulphur emissions have decreased 39 per cent for grandfathered acid gas flaring plants, and 28 per cent for grandfathered sulphur recovery plants. 10 tabs., 3 figs

Wet precipitators for sulphuric acid plants

International Nuclear Information System (INIS)

Ojanpera, R.O.

1989-01-01

Both the service requirements and design construction details have changed considerably in recent years for wet electrostatic precipitators as used for gas cleaning ahead of metallurgical sulphuric acid plants. Increased concern over acid quality has resulted in more emphasis on dust efficiencies compared to collection of acid mist. Also, higher static operating pressures have caused large structural loads on casing and internal components. In this paper these two issues are addressed in the following ways: Recognition that all dusts do not collect similarly. The mechanism by which various dusts collect affect the design of the entire wet gas cleaning system. Use of both traditional and newer materials of construction to accommodate the higher design pressures while still maintaining corrosion resistance

Passivation of chalcopyrite during the leaching with sulphuric acid solution in presence of sodium nitrate

Directory of Open Access Journals (Sweden)

Sokić Miroslav D.

2010-01-01

Full Text Available In this work, the process of the chalcopyrite leaching in sulphuric acid solution was investigated. Sodium nitrate was used as oxidant in the leaching process. Chemical reactions of leaching and their thermodynamic possibilities are predicted based on the calculated Gibbs energies and analysis of E−pH diagrams. The negative values of the Gibbs energy show that all chemical reactions are thermodynamically feasible at atmospheric pressure and in a temperature range 25-90°C. At high electrode potential and low pH values, Cu2+, Fe2+ and Fe3+ ions exist in water solutions. The increase of temperature reduces the probability of Fe3+ ion existence in the system. The chalcopyrite concentrate, enriched in the “Rudnik” flotation plant, with 27.08% Cu, 25.12% Fe, 4.15% Zn and 2.28% Pb was used in the work. XRD and DTA analysis of the concentrate reveals that the sample contains mainly the chalcopyrite with small amount of sphalerite. For the description of the reaction of leaching process the leach residuals, obtained at different conditions, were chosen for XRD, TG/DTA and SEM/EDX analyses. The elemental sulphur and chalcopyrite phases identified in leach residuals confirm our prediction that the elemental sulphur is formed during the leaching process. Accordingly, elemental sulphur is the main product of the reaction, while a minor amount of sulphide sulphur is oxidized to sulphate during the leaching. The sulphur formed during the reaction was precipitated at the particle surfaces, and slowed down the leaching rate in the final stage of leaching process. In the initial stage, the reaction rate was controlled by the surface reaction. The mechanism, latter has been changed into a diffusion controlled one.

Kinetics and mechanism of sphalerite leaching by sodium nitrate in sulphuric acid solution

Directory of Open Access Journals (Sweden)

Sokić M.

2012-01-01

Full Text Available Interest for application of hydrometallurgical processes in a processing of complex sulphide ores and concentrates has increased in recent years. Their application provides better metal recoveries and reduced emission of gaseous and toxic ageneses in the environment. The kinetics and mechanism of sphalerite leaching from complex sulphide concentrate with sulphuric acid and sodium nitrate solution at standard conditions was presented in this paper. The influences of temperature and time on the leaching degree of zinc were investigated and kinetic analysis of the process was accomplished. With temperature increasing from 60 to 90°C, the zinc leaching increased from 25.23% to 71.66% after 2 hours, i.e. from 59.40% to 99.83% after 4 hours. The selected kinetic model indicated that the diffusion through the product layer was the rate-controlling step during the sphalerite leaching. The activation energy was determined to be 55 kJ/mol in the temperature range 60-90°C. XRD, light microscopy and SEM/EDX analyses of the complex concentrate and leach residue confirmed formation of elemental sulphur and diffusion-controlled leaching mechanism.

THE SOLUBILITY OF MILAS BAUXITE ORE IN SULPHURIC ACI

Directory of Open Access Journals (Sweden)

Mustafa GULFEN

2001-06-01

Full Text Available The effects of calcination conditions,sulphuric acid concentrations and dissolvingtemperature and period as parameters to thesolubility of the bauxite ore from Gobekdagı reservesin Mugla-Milas region were investigated. The bauxitesamples were calcined in different periods at differenttemperatures. Then the solubility of the calcinedbauxite samples in sulphuric acid solution wasexamined. Dissolving activation energy (Ea wascalculated using the optimum kinetics equation andthe results obtained from the solubility studiesexamined dissolving temperatures and periods

An analytical procedure for determination of sulphur species and isotopes in boreal acid sulphate soils and sediments

Directory of Open Access Journals (Sweden)

K. BACKLUND

2008-12-01

Full Text Available An analytical scheme suitable for boreal acid sulphate (AS soils and sediments was developed on the basis of existing methods. The presented procedure can be used to quantify and discriminate among acid volatile sulphide, cold chromium reducible sulphur, hot chromium reducible sulphur, elemental sulphur, sulphate sulphur, organic sulphur, total reducible sulphur and total sulphur. The sulphur fractions are recovered as either Ag2S or BaSO4 precipitates and can further be used for isotope analysis. Overlaps between sulphur species are common during speciation, and must be minimized. Some of these overlaps are caused by poor sampling and storage, inappropriate conditions during the distillation, or natural variations in the sample (e.g. Fe3+ interference and grain size. The procedural impact was determined by conducting tests on both artificial and natural samples containing one or several sulphur species. The method is applied on reduced sediment from an AS soil locality (Överpurmo and a brackish lake (Larsmo Lake in western Finland and the results, including S-isotopes, are discussed.;

Analyses on the formation of atmospheric particles and stabilized sulphuric acid clusters

Energy Technology Data Exchange (ETDEWEB)

Paasonen, P.

2012-11-01

Aerosol particles have various effects on our life. They affect the visibility and have diverse health effects, but are also applied in various applications, from drug inhalators to pesticides. Additionally, aerosol particles have manifold effects on the Earths' radiation budget and thus on the climate. The strength of the aerosol climate effect is one of the factors causing major uncertainties in the global climate models predicting the future climate change. Aerosol particles are emitted to atmosphere from various anthropogenic and biogenic sources, but they are also formed from precursor vapours in many parts of the world in a process called atmospheric new particle formation (NPF). The uncertainties in aerosol climate effect are partly due to the current lack of knowledge of the mechanisms governing the atmospheric NPF. It is known that gas phase sulphuric acid most certainly plays an important role in atmospheric NPF. However, also other vapours are needed in NPF, but the exact roles or even identities of these vapours are currently not exactly known. In this thesis I present some of the recent advancements in understanding of the atmospheric NPF in terms of the roles of the participating vapours and the meteorological conditions. Since direct measurements of new particle formation rate in the initial size scale of the formed particles (below 2 nm) are so far infrequent in both spatial and temporal scales, indirect methods are needed. The work presented on the following pages approaches the NPF from two directions: by analysing the observed formation rates of particles after they have grown to sizes measurable with widely applied instruments (2 nm or larger), and by measuring and modelling the initial sulphuric acid cluster formation. The obtained results can be summarized as follows. (1) The observed atmospheric new particle formation rates are typically connected with sulphuric acid concentration to the power close to two. (2) Also other compounds, most

Effects of cold stratification, sulphuric acid, submersion in hot and ...

African Journals Online (AJOL)

Effects of cold stratification, sulphuric acid, submersion in hot and tap water pretreatments in the greenhouse and open field conditions on germination of bladder-Senna ( Colutea armena Boiss. and Huet.) seeds.

SOSA – a new model to simulate the concentrations of organic vapours and sulphuric acid inside the ABL – Part 1: Model description and initial evaluation

DEFF Research Database (Denmark)

Boy, M.; Sogachev, Andrey; Lauros, J.

2010-01-01

Chemistry in the atmospheric boundary layer (ABL) is controlled by complex processes of surface fluxes, flow, turbulent transport, and chemical reactions. We present a new model SOSA (model to simulate the concentration of organic vapours and sulphuric acid) and attempt to reconstruct the emissions...... in the surface layer we were able to get a reasonable description of turbulence and other quantities through the ABL. As a first application of the model, we present vertical profiles of organic compounds and discuss their relation to newly formed particles....

SOSA – a new model to simulate the concentrations of organic vapours and sulphuric acid inside the ABL – Part 1: Model description and initial evaluation

DEFF Research Database (Denmark)

Boy, M.; Sogachev, Andrey; Lauros, J.

2011-01-01

Chemistry in the atmospheric boundary layer (ABL) is controlled by complex processes of surface fluxes, flow, turbulent transport, and chemical reactions. We present a new model SOSA (model to simulate the concentration of organic vapours and sulphuric acid) and attempt to reconstruct the emissions...... in the surface layer we were able to get a reasonable description of turbulence and other quantities through the ABL. As a first application of the model, we present vertical profiles of organic compounds and discuss their relation to newly formed particles....

Automatic colorimetric determination of low concentrations of sulphate for measuring sulphur dioxide in ambient air

Energy Technology Data Exchange (ETDEWEB)

Persson, G A

1966-01-01

An automatic colorimetric method for the determination of low concentrations of sulphate (0-10 microgram/ml) using the thoron indicator is described. Total amounts of sulphate as small as 0.3 micrograms can be determined. The sulphate is precipitated with barium perchlorate and the excess of barium is indicated with 1-(o-arsenophenylazo)-2-naphthol-3-6-disulfonic acid(thoron). The procedure is worked out primarily for the determination of sulphur dioxide in air after absorption in diluted hydrogen peroxide.

Cellulose sulphuric acid as a biodegradable catalyst for conversion ...

Indian Academy of Sciences (India)

This article describes simple and efficient method for the diazotization and azidation of different aromatic amines over cellulose sulphuric acid, sodium nitrite and sodium azide under mild conditions at room temperature. Various aryl amines possessing electron-withdrawing groups or electron-donating groups have been ...

Acid curing and baking of bastnasite ore and concentrate

International Nuclear Information System (INIS)

Topkaya, Y.; Akkurt, S.

1998-01-01

Full text: In this study, the hydrometallurgical evaluation of a rare earth ore as well as a concentrate obtained from this was done at laboratory. For the mentioned study, a bastnasite type rare earth ore located in Beylikahir in Turkey was used. The total rare earth oxide (REO) content of the deposit was estimated to be 1 million tons with an average concentration of 3.42%REO. The rare earths were contained in bastnasite mineral. The other constituents of the ore were calcium fluoride (52.5%), barite (25.4%), calcite (2.8%) and minor amounts of thorium, iron, manganese, etc. The bastnasite mineral occurred either as cement material between fluoride and barite particles or as intimately associated with these minerals. The rare earth elements were enriched considerably in sub-sieve sizes. After extensive research about the physical concentration of this ore, two different metallurgical routes were followed for the extraction of REE from the ore itself or the preconcentrate obtained by attrition scrubbing and desliming by cyclones. In order to increase the grade of the concentrate, upgrading of the preconcentrate by multigravity was also tried. The two metallurgical routes tested were: Sulphuric acid curing and water leaching; Sulphuric acid baking and subsequent water leaching. The results of the leaching experiments were found to be quite promising. Leach recoveries up to 90% were easily obtainable. In the case of acid baking, hydrofluoric acid recover as a by-product was also possible

Past and future trends in concentrations of sulphur and nitrogen compounds in the Arctic

DEFF Research Database (Denmark)

Hole, Lars R.; Christensen, Jesper H.; Ruoho-Airola, Tuija

2009-01-01

Recent trends in nitrogen and sulphur compounds in air and precipitation from a range of Arctic monitoring stations are presented, with seasonal data from the late 70s to 2004 or 2005. Earlier findings of declining sulphur concentrations are confirmed for most stations, while the pattern is less ...

In-situ Spectroscopic Studies and Modelling of Crystallization Processes of Sulphuric Acid Catalysts

DEFF Research Database (Denmark)

Oehlers, C.; Fehrmann, Rasmus; Masters, Stephen Grenville

1996-01-01

Deactivation of commercial and prototype sulphuric acid catalysts has been investigated in-situ by ESR spectroscopy. The influence of support pore structure,and the chemical composition of the catalyst and the gas phase was dicussed.A statistical lattice model was applied to describe the crystall......Deactivation of commercial and prototype sulphuric acid catalysts has been investigated in-situ by ESR spectroscopy. The influence of support pore structure,and the chemical composition of the catalyst and the gas phase was dicussed.A statistical lattice model was applied to describe...

Influence of solid loading on D-xylose production through dilute sulphuric acid hydrolysis of olive stones

Directory of Open Access Journals (Sweden)

Cuevas, M.

2015-09-01

Full Text Available The selective hydrolysis of hemicellulose from olive stones was attempted in order to achieve a maximum D-xylose yield. For this aim, batch hydrolysis was conducted under different operating conditions of temperature, acid concentration and solid loading. Firstly, distilled water, sulphuric acid and nitric acid were assessed as hydrolytic agents at different temperatures (200, 205, 210 and 220 °C and at a fixed acid concentration (0.025 M. Sulphuric acid and 200 °C were selected for the subsequent dilute acid hydrolysis optimization based on the obtained D-xylose yields. The combined influence of solid loading (from 29.3 to 170.7 g olive stones into 300 mL acid solution and sulphuric acid concentration (0.006–0.034 M on the release of D-xylose was then estimated by response surface methodology. According to a statistical analysis, both parameters had significant interaction effects on D-xylose production. The results illustrated that the higher the solid loading, the higher the required acid concentration. The decrease in the solid/liquid ratio in the reactor had a positive effect on D-xylose extraction and on the amount of acid used. The optimum solid loading and sulphuric acid concentration were determined to be 50 g (solid/liquid ratio 1/6 and 0.016 M, respectively. Under these conditions, the predicted D-xylose yield (expressed as g of sugar per 100 g of dry matter fed was 20.4 (87.2% of maximum attainable.Se ha desarrollado una hidrólisis selectiva de la fracción hemicelulósica del hueso de aceituna con el fin de obtener el máximo rendimiento de D-xilosa. Para ello las hidrólisis se llevaron a cabo en un reactor discontinuo a distintas condiciones de temperatura, concentración de ácido y carga de sólidos. En primer lugar se evaluó la capacidad hidrolítica del agua destilada y de los ácidos nítrico y sulfúrico a distintas temperaturas (200, 205, 210 y 220°C manteniendo fija la concentración de ácido (0,025 M. A partir de

Effects of sulphuric acid, mechanical scarification and wet heat ...

African Journals Online (AJOL)

Effects of different treatment methods on the germination of seeds of Parkia biglobosa (mimosaceae) were carried out. Prior treatment of seeds with sulphuric acid, wet heat and mechanical scarification were found to induce germination of the dormant seeds. These methods could be applied to raise seedlings of the plant for ...

Synergistic inhibition between o-phenanthroline and chloride ion for steel corrosion in sulphuric acid

International Nuclear Information System (INIS)

Li Xueming; Tang Libin; Li Lin; Mu Guannan; Liu Guangheng

2006-01-01

The corrosion inhibition of cold rolled steel in 0.5 M sulphuric acid in the presence of o-phenanthroline and sodium chloride (NaCl) has been investigated by using weight loss and electrochemical techniques. The experimental data suggest that the inhibition efficiency increases with increasing NaCl concentration in the presence of 0.0002 M o-phenanthroline, but decreases with increasing temperature. A synergistic effect is observed when o-phenanthroline and chloride ions are used together to prevent cold rolled steel corrosion in 0.5 M sulphuric acid. The polarization curves showed that the complex of o-phenanthroline and NaCl acts as a mixed type inhibitor. The experimental results suggested that the presence of chloride ions in the solution stabilized the adsorption of o-phenanthroline molecules on the metal surface and improved the inhibition efficiency of o-phenanthroline. The adsorption of the complex accords with the Langmuir adsorption isotherm. Some thermodynamic parameters such as adsorption heat, adsorption entropy and adsorption free energy have been calculated by employing thermodynamic equations. Kinetic parameters such as apparent activation energy and pre-exponential factor have been calculated and discussed

Sulphur fertilization influences the sulphur species composition in Allium sativum: sulphomics using HPLC-ICPMS/MS-ESI-MS/MS.

Science.gov (United States)

Raab, Andrea; Ronzan, Marilena; Feldmann, Joerg

2017-10-18

Garlic (A. sativum) contains a large number of small sulphur (S)-containing metabolites, which are important for its taste and smell and vary with A. sativum variety and growth conditions. This study was designed to investigate the influence of different sulphur-fertilization regimes on low molecular weight S-species by attempting the first sulphur mass balance in A. sativum roots and bulbs using HPLC-ICPMS/MS-ESI-MS/MS. Species unspecific quantification of acid soluble S-containing metabolites was achieved using HPLC-ICP-MS/MS. For identification of the compounds, high resolution ESI-MS (Orbitrap LTQ and q-TOF) was used. The plants contained up to 54 separated sulphur-containing compounds, which constitute about 80% of the total sulphur present in A. sativum. The roots and bulbs of A. sativum contained the same compounds, but not necessarily the same amounts and proportions. The S-containing metabolites in the roots reacted more sensitively to manipulations of sulphur fertilization than those compounds in the bulbs. In addition to known compounds (e.g. γ-glutamyl-S-1-propenylcysteine) we were able to identify and partially quantify 31 compounds. Three as yet undescribed S-containing compounds were also identified and quantified for the first time. Putative structures were assigned to the oxidised forms of S-1-propenylmercaptoglutathione, S-2-propenylmercaptoglutathione, S-allyl/propenyl-containing PC-2 and 2-amino-3-[(2-carboxypropyl)sulfanyl]propanoic acid. The parallel use of ICP-MS/MS as a sulphur-specific detector and ESI-MS as a molecular detector simplifies the identification and quantification of sulphur containing metabolites without species specific standards. This non-target analysis approach enables a mass balance approach and identifies the occurrence of the so far unidentified organosulphur compounds. The experiments showed that the sulphur-fertilization regime does not influence sulphur-speciation, but the concentration of some S

Determination of sulphur with total reflection x-ray spectrometry

International Nuclear Information System (INIS)

Steinmeyer, S.; Kolbesen, B.O.

2000-01-01

The potential and limitations of total reflection x-ray spectrometry (TXRF) were tested for the quantitative determination of the light element sulphur in inorganic and biological samples. As representatives of inorganic samples alkali, transition metal, magnesium and aluminum sulphates were investigated. As biological samples the sulphur containing amino acid methionine and the pharmaceutical drug insulin were chosen. All measurements were performed on a TXRF-spectrometer EXTRA IIA (Atomika Instruments, Oberschleissheim/Germany) using tungsten L-radiation as the excitation tube. Various concentrations of all samples ranging from 20 mg/l to 0.5 mg/l were determined. In addition the surface topography and thickness of the dry residue of these samples were investigated with SEM and a thickness profilometer (Alpha-Step). The result show that the reliable determination of sulphur in sulphates depends on the cation involved. Alkali sulphates like Na 2 SO 4 , or K 2 SO 4 form bulky residues resulting in significant deviations of the recovery rate of sulphur. In this case the use of smoothing detergents like 1 % HF, 1 % malic acid and 2 % hydrazinhydrat was found to be necessary for accurate determination. The results for the biological samples agree well with the expected values. The investigations lead to the conclusion that TXRF combined with a proper samples preparation is well suited for the determination of sulphur in different samples with various concentrations and matrices. (author)

Intensification of zinc dissolution process in sulphuric acid

Directory of Open Access Journals (Sweden)

Stanojević D.

2005-01-01

Full Text Available Many high purity salts are produced by dissolving pure metal in non-oxidizing mineral acids. If hydrogen overpotential on the given metal is high, then the rate of overall process is defined by reaction of hydrogen ion reduction. This study investigated the possibility of accelerated dissolving of metal zinc in sulphuric acid by introducing copper cathode on which evolving hydrogen is much easier than on zinc. It was found out that the acceleration of zinc dissolving is possible and, at constant surface of copper cathode depends on the quality of electrical contact between copper electrode and zinc.

Effects of structural and textural grain characteristics on leaching of sulphide minerals from a polymetallic concentrate by sodium nitrate and sulphuric acid solution

Directory of Open Access Journals (Sweden)

Sokić Miroslav D.

2017-01-01

Full Text Available In this paper, the influence of structural and textural characteristics of sulfide minerals on their leaching from a polymetallic concentrate by sulfuric acid and sodium nitrate solution is presented. The starting material was Pb–Zn–Cu sulphide polymetallic concentrate enriched during the flotation of a polymetallic ore in the "Rudnik" flotation plant (Rudnik – Serbia. Leaching experiments were carried out in a closed glass reactor, which provides stable hermetic conditions and allows heating at constant temperature. Chemical, XRD, qualitative and quantitative microscopic and SEM/EDX analyses were used to characterizes samples of the polymetallic concentrate and leach residue. It was determined that chalcopyrite, sphalerite, galena, pyrrhotite and quartz were present in the polymetallic concentrate. The content of sulphide minerals was 69.5%, of which 60.9% occurred as liberated grains: 88.3% of chalcopyrite, 59.3% of sphalerite, 25.1% of galena and 51.6% of pirrhotite. The rest of chalcopyrite, sphalerite, galena and pirrhotite grains were in the forms of inclusions, impregnations, and simple and complex intergrowths. During the leaching process by sodium nitrate and sulphuric acid solution, it was shown previously that the leaching rate of sulphide minerals decreased with time while a part of the sulphide minerals remained in the leach residue. After leaching at 80°C for 120 min, the yields were 69.8, 82.7 and 67.1% for Cu, Zn and Fe, respectively. Lead, in the form of insoluble anglesite, remained in the leach residue. In addition to the anglesite, unleached sulfide minerals and quartz, elemental sulfur was found in the solid residue. The content of sulphide minerals was 35% of which 33.7% minerals occur independently. In specific, 54.7% of chalcopyrite, 31.9% of sphalerite, 8.2% of galena and 37.6% of pyrrhotite appear as separate grains with highly corroded surfaces. Therefore, the structural assembly of sulphide grains in the

Kinetics of bromide catalysed oxidation of dextrose by cerium (IV) in aqueous sulphuric acid solution

International Nuclear Information System (INIS)

Sharma, J.; Sah, M.P.

1994-01-01

Kinetics of bromide catalysed oxidation of dextrose by Ce IV in aqueous sulphuric acid medium show first order dependence each in dextrose and cerium(IV). The reaction rate decreases on increasing the concentration of hydrogen ion. The increase in [HSO 4 - ] or [SO 4 2- ] decreases the rate. The bromide ion shows positive catalytic effect on the reaction rate. The value of activation energy has been calculated and a suitable mechanism confirming to the kinetic data is proposed. (author). 3 refs., 3 tabs

Growth of Sulphuric Acid Nanoparticles Under Wet and Dry Conditions

Czech Academy of Sciences Publication Activity Database

Škrabalová, Lenka; Brus, David; Antilla, T.; Ždímal, Vladimír; Lihavainen, H.

2014-01-01

Roč. 14, č. 12 (2014), s. 6461-6475 ISSN 1680-7316 R&D Projects: GA AV ČR IAA200760905 Grant - others:AFCEP(FI) 1118615 Institutional support: RVO:67985858 Keywords : binary nucleation * sulphuric acid - water * condensational growth Subject RIV: BJ - Thermodynamics Impact factor: 5.053, year: 2014

Quantification of sulphur amino acids by ultra-high performance liquid chromatography in aquatic invertebrates.

Science.gov (United States)

Thera, Jennifer C; Kidd, Karen A; Dodge-Lynch, M Elaine; Bertolo, Robert F

2017-12-15

We examined the performance of an ultra-high performance liquid chromatography method to quantify protein-bound sulphur amino acids in zooplankton. Both cysteic acid and methionine sulfone were linear from 5 to 250 pmol (r 2  = 0.99), with a method detection limit of 13 pmol and 9 pmol, respectively. Although there was no matrix effect on linearity, adjacent peaks and co-eluting noise from the invertebrate proteins increased the detection limits when compared to common standards. Overall, performance characteristics were reproducible and accurate, and provide a means for quantifying sulphur amino acids in aquatic invertebrates, an understudied group. Copyright © 2017 Elsevier Inc. All rights reserved.

Empirical modeling of solvent extraction of uranium from sulphuric acid medium using PC-88A and TOPO as extractants

International Nuclear Information System (INIS)

Biswas, S.; Roy, S.B.; Pathak, P.N.; Manchanda, V.K.; Singh, D.K.

2011-01-01

Extraction behavior of uranium (VI) from sulphuric acid medium using PC-88A (H 2 A 2 , dimer form) and a mixture of PC-88A + TOPO in n-dodecane has been investigated. The extraction data have been used to develop a mathematical model correlating percentage extraction (%E) with PC-88A and TOPO concentration. It can be used to predict the steady-state concentrations of metal ion under the conditions of the present work. (author)

Hydrothermal Alteration in an Acid-Sulphate Geothermal Field: Sulphur Springs, Saint Lucia

Science.gov (United States)

Joseph, E. P.; Barrett, T. J.

2017-12-01

Sulphur Springs is a vigorous geothermal field associated with the Soufrière Volcanic Centre in southern Saint Lucia. Bubbling hydrothermal pools are rich in sodium-calcium sulphate, with pHs of 3-7 and temperatures of 41-97ºC. Fumaroles have temperatures up to, and at times above, 100°C. Gases from bubbling pools and fumaroles have high contents of CO2 (601-993 mmol/mol) and H2S (3-190 mmol/mol). To investigate the nature and extent of hydrothermal alteration, detailed chemical analysis was carried out on 25 altered rocks, 10 sediments from pools and creeks in the main discharge area, and 15 little-altered rocks up to 2 km away from geothermal field. Eight altered samples were also analysed for stable isotope compositions, with mineralogy determined by X-ray diffraction and mineral liberation analysis. Least-altered host rocks comprise calc-alkaline feldspar-quartz-porphyritic dacites of near-uniform composition that form massive domes and volcaniclastic units. These rocks were emplaced 10-30 Ka ago (Lindsay et al. 2013). Within the geothermal field, the dacites have been highly altered to kaolinite, quartz, cristobalite, alunite, natroalunite, smectite, native sulphur, jarosite, gypsum and amorphous compounds. Muds from grey to blackish hydrothermal pools additionally contain iron sulphides, mainly pyrite. Despite intense alteration of the original dacites, Zr and Ti have remained essentially immobile, allowing the calculation of mass changes. Major depletions of Fe, Mg, Ca, Na and commonly Si occur over an area of at least 200 x 400 m. The most altered rocks also show losses of Al, light REE and Y, implying leaching by highly acidic waters. A few altered rocks have, however, gained Al together with Si and P. Also present are m-scale zones of silica + native sulphur, wherein the silica appears to represent a residue from the leaching of dacite, rather than a hydrothermal addition. Delta-34S values of samples containing mixtures of sulphates, native sulphur and

Sulphurous mineral waters

Directory of Open Access Journals (Sweden)

Iluta Alexandru

2011-09-01

Full Text Available Sulphurous waters contain at least 1mg H2S, HS, S or thiosulphate per liter or complex colloidal sulfur water is presented as of simple or mixed sulphide (alkali, carbonated, chlorinated sodium.In the sulphurous waters, sulfur is found in several forms (hydrogen sulfide, free sulfide, sulfide groups, polysulfides acids. Yellow, opalescent white precipitate and deposit a glass of water on the bottom of sulphur oxidation by indicates the intensity of the wateroxidation process by oxygen in the air.

Effects of sulphuric acid and hot water treatments on seed ...

African Journals Online (AJOL)

A study was carried out to investigate the effects of sulphuric acid and hot water treatments on the germination of Tamarind (Tamarindus indica L). Seeds were placed on moistened filter papers in 28 cm diameter Petri dishes under laboratory condition for germination. 330 seeds of T. indica (10 seeds per Petri dish) with ...

Concentration levels and spatial distribution of sulphur and metals in fine-grained sediments in western Finland

Directory of Open Access Journals (Sweden)

M. ÅSTRÖM

2008-12-01

Full Text Available On the coastal plains of Finland, widespread Holocene marine and lacustrine sediments have developed into acid sulphate soil as a result of extensive artificial drainage for agricultural purposes. This has caused a variety of environmental problems. The aim of this study was to determine the concentration levels and spatial distribution of sulphur, carbon and metals [titanium, vanadium, chromium, manganese (Mn, iron, cobalt (Co, nickel (Ni, copper (Cu, zinc (Zn] in these sediments, in order to increase the geochemical understanding of the parent materials from which acid sulphate soil develops. Sediment samples were collected at 317 sites from a depth of 1.5–3 m. While the sediments have high S (sulphide concentrations (median = 0.54% and thus a strong acidification potential, they carry transition metals mainly in smallsized silicates close to “background concentrations” far below contamination limits. The previously documented extensive release of Co, Cu, Mn, Ni and Zn from oxidised and acidified layers of these sediments (i.e. acid sulphate soil is thus not explained by anomalously high natural or anthropogenic metal concentrations of the soils/sediments, but by an inherent highly mobile metal pool. Spatial-distribution maps highlight areas of elevated S and Mn concentrations, where it is likely that ditching and subsequent oxidation will result in an exceptionally large release of protons and Mn respectively.;

Quantitative Aspects of Sulphur Metabolism in the Ruminant

Energy Technology Data Exchange (ETDEWEB)

Landis, J. [Institut fuer Tierernaehrung, Eidgenoessische Technische Hochschule, Zurich (Switzerland)

1968-07-01

In a series of four experiments {sup 35}S sulphate was given intra-ruminally to lactating dairy goats at feeding times (twice daily) during periods of 10 to 11 d. Rumen contents were sampled on the 8th, 9th and 10th day of {sup 35}S application. Radioactivity was determined in the volatile sulphur fraction (sulphide-sulphur) and in protein-bound sulphur (fraction insoluble in trichloroacetic acid). The ratio between the specific activities of protein sulphur and of sulphide sulphur was considered to be an estimate for that fraction of sulphur-containing amino acids present in the proteins of rumen contents, which was synthesized by microorganisms. This interpretation is based on the assumption that sulphide is the most important source of inorganic sulphur for the synthesis of sulphur amino acids and that incorporation of inorganic sulphur compounds of a a higher state of oxidation into organic molecules may quantitatively be neglected. In three experiments the animals received rations containing 16% to 17% crude protein. In these experiments the ratio of specific activities of protein and sulphide sulphur was found to vary from 0.32 to 0.41. According to the assumptions mentioned above, this would indicate that 32 to 41% of the total amount of protein-bound sulphur amino acids were synthesized by microorganisms from inorganic (sulphide) sulphur. In the fourth experiment the animal received a ration containing only 10% protein but supplemented with urea to bring the total crude protein content to 13%. In this experiment the ratio of specific activities was 0.70, indicating a much higher contribution of microbial synthesis of sulphur amino acids than in the experiments with a more abundant protein supply. The time course of the specific activity of protein-bound-sulphur in the milk is taken as a reference base for an interpretation of labelling of body proteins in terms of turnover rates.

Solid state radiolysis of sulphur-containing amino acids. Cysteine, cystine and methionine

International Nuclear Information System (INIS)

Franco Cataldo; Pietro Ragni; Susana Iglesias-Groth; Arturo Manchado

2011-01-01

The sulphur-containing proteinaceous amino acids l-cysteine, l-cystine and l-methionine were irradiated in the solid state to a dose of 3.2 MGy. This dose corresponds to that delivered by radionuclide decay in a timescale of 1.05 x 10 9 years to the organic matter buried at a depth >20 m in comets and asteroids. The purity of the sulphur-containing amino acids was studied by differential scanning calorimetry (DSC) before and after the solid state radiolysis and the preservation of the chirality after the radiolysis was studied by chirooptical methods (optical rotatory dispersion, ORD) and by FT-IR spectroscopy. Although the high radiation dose of 3.2 MGy delivered, all the amino acids studied show a high radiation resistance. The best radiation resistance was offered by l-cysteine. The radiolysis of l-cysteine leads to the formation of l-cystine. The radiation resistance of l-methionine is not at the level of l-cysteine but also l-methionine is able to survive the dose of 3.2 MGy. Furthermore in all cases examined the preservation of chirality after radiolysis was clearly observed by the ORD spectroscopy although a certain level of radioracemization was measured in all cases. The radioracemization is minimal in the case of l-cysteine and is more pronounced in the case of l-methionine. In conclusion, the study shows that the sulphur-containing amino acids can survive for 1.05 x 10 9 years and, after extrapolation of the data, even to the age of the Solar System i.e. to 4.6 x 10 9 years. (author)

Sources of increase in lowermost stratospheric sulphurous and carbonaceous aerosol background concentrations during 1999–2008 derived from CARIBIC flights

Directory of Open Access Journals (Sweden)

Johan Friberg

2014-03-01

Full Text Available This study focuses on sulphurous and carbonaceous aerosol, the major constituents of particulate matter in the lowermost stratosphere (LMS, based on in situ measurements from 1999 to 2008. Aerosol particles in the size range of 0.08–2 µm were collected monthly during intercontinental flights with the CARIBIC passenger aircraft, presenting the first long-term study on carbonaceous aerosol in the LMS. Elemental concentrations were derived via subsequent laboratory-based ion beam analysis. The stoichiometry indicates that the sulphurous fraction is sulphate, while an O/C ratio of 0.2 indicates that the carbonaceous aerosol is organic. The concentration of the carbonaceous component corresponded on average to approximately 25% of that of the sulphurous, and could not be explained by forest fires or biomass burning, since the average mass ratio of Fe to K was 16 times higher than typical ratios in effluents from biomass burning. The data reveal increasing concentrations of particulate sulphur and carbon with a doubling of particulate sulphur from 1999 to 2008 in the northern hemisphere LMS. Periods of elevated concentrations of particulate sulphur in the LMS are linked to downward transport of aerosol from higher altitudes, using ozone as a tracer for stratospheric air. Tropical volcanic eruptions penetrating the tropical tropopause are identified as the likely cause of the particulate sulphur and carbon increase in the LMS, where entrainment of lower tropospheric air into volcanic jets and plumes could be the cause of the carbon increase.

Silica Sulphuric Acid as an Efficient Catalyst for the Catalytic and ...

African Journals Online (AJOL)

NJD

presence of a catalytic amount of silica sulphuric acid under micellar media in moderate to good yields. KEYWORDS. Sodium ... Production of aromatic nitro compounds is an important industrial process and involves the unsolved problems of ... V7 and Re9) and titanium and chromium silicates.10 Some of the procedures ...

Procedure for recovery from an uranium containing concentrate and phosphoric acid, as well as an uranium containing concentrate and phosphoric acid obtained by this procedure

International Nuclear Information System (INIS)

1980-01-01

The phosphate ore is dissolved in sulphuric acid and the formed calcium sulphate is separated from the solution. The uranium is then precipitated by adding ammonium fluoride solution to the remaining phosphoric acid solution. When the phosphate ore is dissolved in sulphuric acid, fluorine gas is liberated and this is then used to produce the ammonium fluoride solution. (Th.P.)

Process for treatment of pyrochlore concentrates

International Nuclear Information System (INIS)

Charlot, G.

1976-01-01

A continuous process is described for extraction of niobium, rare earths and thorium from niobium ore concentrates which includes digesting the ore with a hot solution containing 13 to 16 moles of sulphuric acid per liter, diluting the solution to a concentration of 10 to 13 moles of sulphuric acid per liter, separating the insolubles from the solution which includes alkaline earth sulphates and the sulphates of thorium and rare earths that are present, reducing titanium in solution to the trivalent state and diluting the solution to a concentration of 5 to 7 moles of sulphuric acid per liter, separating the precipitated niobium oxide and sulphates of thorium and rare earths, and then concentrating the resulting solution to the level desired for recycle to the digestion stage. 10 Claims, No Drawings

Molecular understanding of sulphuric acid-amine particle nucleation in the atmosphere.

Science.gov (United States)

Almeida, João; Schobesberger, Siegfried; Kürten, Andreas; Ortega, Ismael K; Kupiainen-Määttä, Oona; Praplan, Arnaud P; Adamov, Alexey; Amorim, Antonio; Bianchi, Federico; Breitenlechner, Martin; David, André; Dommen, Josef; Donahue, Neil M; Downard, Andrew; Dunne, Eimear; Duplissy, Jonathan; Ehrhart, Sebastian; Flagan, Richard C; Franchin, Alessandro; Guida, Roberto; Hakala, Jani; Hansel, Armin; Heinritzi, Martin; Henschel, Henning; Jokinen, Tuija; Junninen, Heikki; Kajos, Maija; Kangasluoma, Juha; Keskinen, Helmi; Kupc, Agnieszka; Kurtén, Theo; Kvashin, Alexander N; Laaksonen, Ari; Lehtipalo, Katrianne; Leiminger, Markus; Leppä, Johannes; Loukonen, Ville; Makhmutov, Vladimir; Mathot, Serge; McGrath, Matthew J; Nieminen, Tuomo; Olenius, Tinja; Onnela, Antti; Petäjä, Tuukka; Riccobono, Francesco; Riipinen, Ilona; Rissanen, Matti; Rondo, Linda; Ruuskanen, Taina; Santos, Filipe D; Sarnela, Nina; Schallhart, Simon; Schnitzhofer, Ralf; Seinfeld, John H; Simon, Mario; Sipilä, Mikko; Stozhkov, Yuri; Stratmann, Frank; Tomé, Antonio; Tröstl, Jasmin; Tsagkogeorgas, Georgios; Vaattovaara, Petri; Viisanen, Yrjo; Virtanen, Annele; Vrtala, Aron; Wagner, Paul E; Weingartner, Ernest; Wex, Heike; Williamson, Christina; Wimmer, Daniela; Ye, Penglin; Yli-Juuti, Taina; Carslaw, Kenneth S; Kulmala, Markku; Curtius, Joachim; Baltensperger, Urs; Worsnop, Douglas R; Vehkamäki, Hanna; Kirkby, Jasper

2013-10-17

Nucleation of aerosol particles from trace atmospheric vapours is thought to provide up to half of global cloud condensation nuclei. Aerosols can cause a net cooling of climate by scattering sunlight and by leading to smaller but more numerous cloud droplets, which makes clouds brighter and extends their lifetimes. Atmospheric aerosols derived from human activities are thought to have compensated for a large fraction of the warming caused by greenhouse gases. However, despite its importance for climate, atmospheric nucleation is poorly understood. Recently, it has been shown that sulphuric acid and ammonia cannot explain particle formation rates observed in the lower atmosphere. It is thought that amines may enhance nucleation, but until now there has been no direct evidence for amine ternary nucleation under atmospheric conditions. Here we use the CLOUD (Cosmics Leaving OUtdoor Droplets) chamber at CERN and find that dimethylamine above three parts per trillion by volume can enhance particle formation rates more than 1,000-fold compared with ammonia, sufficient to account for the particle formation rates observed in the atmosphere. Molecular analysis of the clusters reveals that the faster nucleation is explained by a base-stabilization mechanism involving acid-amine pairs, which strongly decrease evaporation. The ion-induced contribution is generally small, reflecting the high stability of sulphuric acid-dimethylamine clusters and indicating that galactic cosmic rays exert only a small influence on their formation, except at low overall formation rates. Our experimental measurements are well reproduced by a dynamical model based on quantum chemical calculations of binding energies of molecular clusters, without any fitted parameters. These results show that, in regions of the atmosphere near amine sources, both amines and sulphur dioxide should be considered when assessing the impact of anthropogenic activities on particle formation.

An approach for degradation of grape seed and skin proanthocyanidin polymers into oligomers by sulphurous acid.

Science.gov (United States)

Luo, Lanxin; Cui, Yan; Cheng, Jinhui; Fang, Bairui; Wei, Zongmin; Sun, Baoshan

2018-08-01

To develop an efficient method for degradation of grape seed and skin proanthocyanidins polymers into oligomers, an optimized sulphurous acid degradation conditions for grape seed with the temperature of 60 °C, reaction time of 60 min and sample-sulphurous acid ratio of 1:0.2, and for grape skin with the temperature of 40 °C, reaction time of 60 min and sample-sulphurous acid ratio of 1:0.2, were established. Afterwards, HSCCC and prep-HPLC were used to fractionate and isolate individual proanthocyanidin oligomers from the degradation products. Total of ten dimeric or trimeric procyanidins were obtained, and most of them presented high yield (from 0.7 mg to 13.6 mg per run in grape seed and from 0.5 mg to 4.1 mg per run in grape skin) and high purity (over 90%). The proposed method provides a new way for large preparation of oligomeric proanthocyanidins from naturally abundant and wasted polymeric ones. Copyright © 2018 Elsevier Ltd. All rights reserved.

Impact of sulphur fumigation on the chemistry of ginger.

Science.gov (United States)

Wu, Cheng-Ying; Kong, Ming; Zhang, Wei; Long, Fang; Zhou, Jing; Zhou, Shan-Shan; Xu, Jin-Di; Xu, Jun; Li, Song-Lin

2018-01-15

Ginger (Zingiberis Rhizoma), a commonly-consumed food supplement, is often sulphur-fumigated during post-harvest handling, but it remains unknown if sulphur fumigation induces chemical transformations in ginger. In this study, the effects of sulphur fumigation on ginger chemicals were investigated by ultra-high performance liquid chromatography coupled with quadrupole time-of-flight mass spectrometry (UHPLC-QTOF-MS/MS)-based metabolomics. The results showed that sulphur fumigation significantly altered the holistic chemical profile of ginger by triggering chemical transformations of certain original components. 6-Gingesulphonic acid, previously reported as a naturally-occurring component in ginger, was revealed to be a sulphur fumigation-induced artificial derivative, which was deduced to be generated by electrophilic addition of 6-shogaol to sulphurous acid. Using UHPLC-QTOF-MS/MS extracting ion analysis with 6-gingesulphonic acid as a characteristic chemical marker, all the commercial ginger samples inspected were determined to be sulphur-fumigated. The research outcomes provide a chemical basis for further comprehensive safety and efficacy evaluations of sulphur-fumigated ginger. Copyright © 2017 Elsevier Ltd. All rights reserved.

The recuperation of sulphuric acid out of contaminated solutions by electro electrodialysis

International Nuclear Information System (INIS)

Cattoir, S.

1997-05-01

The dismantling of a nuclear reactor results in large amounts of contaminated waste. The amount of waste is minimized by so-called decontamination processes. These decontamination processes result in decontaminated metal as well as contaminated effluents, containing acid and metal salts. Standard treatment of these effluents involves neutralisation of the acid using sodium hydroxide, resulting in the precipitation of hydroxides; and evaporation of the solvent. However, if the acid is extracted out of the decontamination effluents prior to neutralisation, this acid can be re-used in the decontamination process, substantially reducing the final waste. This report investigates the possibility of using Electro Electrodialysis (EED) for the extraction of 900 moles of sulphuric acid out of a 1 m 3 contaminated solution, containing 22 kg of ferrous, chromous, cerous and nickel ions and 1000 moles of sulphuric acid. EED removes acids out of acid/salts solutions, using an electrolyser equipped with an anionic membrane: the acid-anion is displaced by migration through the membrane while the proton is displaced by electrolysis. This report gives a full description of the technique, the lab-scale apparatus, the analyses involved in studying the technique on lab-scale or monitoring it on full scale, the choice of electrode and membrane and of process parameters such as temperature and current density. On lab scale, EED can displace 90% of the acid out of the acid/salt solution just described, at a current density as high as 0.14 A.cm -2 , at 50 degrees Celsius, if the cathode and the anode are of smoothed platina or of platinised titanium, and the anion selective membrane is the Neosepta AMH -membrane of Tokuyama. The study of EED still needs to be completed with a further study of metal deposition on the cathode, and a comparison of the technique to other (electro)membrane techniques

Effect of Nitric and Oxalic Acid Addition on Hard Anodizing of AlCu4Mg1 in Sulphuric Acid

Directory of Open Access Journals (Sweden)

Maximilian Sieber

2018-02-01

Full Text Available The anodic oxidation process is an established means for the improvement of the wear and corrosion resistance of high-strength aluminum alloys. For high-strength aluminum-copper alloys of the 2000 series, both the current efficiency of the anodic oxidation process and the hardness of the oxide coatings are significantly reduced in comparison to unalloyed substrates. With regard to this challenge, recent investigations have indicated a beneficial effect of nitric acid addition to the commonly used sulphuric acid electrolytes both in terms of coating properties and process efficiency. The present work investigates the anodic oxidation of the AlCu4Mg1 alloy in a sulphuric acid electrolyte with additions of nitric acid as well as oxalic acid as a reference in a full-factorial design of experiments (DOE. The effect of the electrolyte composition on process efficiency, coating thickness and hardness is established by using response functions. A mechanism for the participation of the nitric acid additive during the oxide formation is proposed. The statistical significance of the results is assessed by an analysis of variance (ANOVA. Eventually, scratch testing is applied in order to evaluate the failure mechanisms and the abrasion resistance of the obtained conversion coatings.

Use of PSA for design of emergency mitigation systems in a hydrogen production plant using General Atomics SI cycle technology. Section 2: Sulphuric acid decomposition

International Nuclear Information System (INIS)

Mendoza, A.; Nelson, P.F.; Francois, J.L.

2010-01-01

Throughout the past decades, the need to reduce greenhouse gas emissions has prompted the development of technologies for the production of clean fuels through the use of zero emissions primary energy resources, such as heat from high temperature nuclear reactors. One of the most promising of these technologies is the generation of hydrogen by the sulphur-iodine cycle coupled to a high temperature nuclear reactor, initially proposed by General Atomics. By its nature and because these will have to be large-scale plants, development of these technologies from its current phase to its procurement and construction phase, will have to incorporate emergency mitigation systems in all its sections and nuclear-chemical 'tie-in points' to prevent unwanted events that can compromise the integrity of the plant and the nearby population centres. For the particular case of the SI thermochemical cycle, a large number of safety studies have been developed; however, most of these studies have focused on hydrogen explosions and failures in the primary cooling system. While these are the most catastrophic events, it is also true that there are many other events that without having a direct impact on the nuclear-chemical coupling, could jeopardise plant operations, safety of people in nearby communities and bring economic consequences. This study examined one of these events, which is the formation of a toxic cloud driven by an uncontrolled leakage of concentrated sulphuric acid in the second section of the General Atomics SI cycle. In this section, the concentration of sulphuric acid is close to 90% in conditions of high temperature and positive pressure. Under these conditions, sulphuric acid and sulphur oxides from the reactor would immediately form a toxic cloud, that in contact with operators could cause fatalities, or could produce choking, respiratory problems and eye irritation to people in neighbouring towns. The methodology used for this analysis is the design based on

Forest fuel and sulphur

International Nuclear Information System (INIS)

Lundborg, A.

1994-10-01

This report illustrates the sulphur cycle in forest fuel and in the forest ecosystem. The hypothesis is that sulphur dioxide from combustion of forest fuel is not more acidifying than sulphur that is mineralized from tree biomass if it is left in the forest instead of being burnt. The report gives an overview of the sulphur cycle in general together with the acidifying effect of sulphur. The sulphur content in wood biomass is about 1 mg/g in the needles and 0.2-0.3 mg/g in wood. Chipped forest fuel contains 0.2-0.5 mg S/g. A removal of 40 tonnes of felling residues per hectare may contain about 8-30 kg S. The sulphur occurs both in organic, often reduced, form and as sulphate. In situations of high availability to sulphur there will be an increased proportion of sulphate. After combustion some, perhaps half, of the sulphur is left in the ashes, most of which appears to be sulphate. In mineralisation of reduced organic sulphur, of type R-SH, the sulphur is released in the form of sulphide. Hydrogen sulphide, H2S, can be oxidised by microbes to sulphate, which should be acidifying (2 H+ will remain). A very rough estimate suggests that emissions of sulphur dioxide from forest fuel, spread over the period the trees are growing, and on the area from which the trees are taken, corresponds to 0.5% of the sulphur deposition in southern Sweden. Sulphur emissions from biofuel combustion are much lower than Sweden's and the EU's most stringent emission limits for coal. Whole-tree removal with return of ashes will theoretically give a considerable reduction in soil acidity since large quantities of nitrogen are removed and thus the acidifying effect of nitrogen will not occur. This should be of greater importance for forest acidification than the effect of biomass sulphur. 80 refs, numerous tabs

Evaluation of Plants and Weeds Extract on the Corrosion Inhibition of Mild Steel in Sulphuric Acid

Directory of Open Access Journals (Sweden)

Abida Begum

2011-01-01

Full Text Available Experiments were performed in order to determine the inhibitive effects of extracts of plants and weeds namely Parthenium hysterophorus, Dathura stromonium, Azadirachta indica, Helianthus annuus leaves extract for mild steel in sulphuric acid by using weight loss and thermometric technique. Results demonstrated that, all the experimental inhibitors show an adsorption on steel surface according to Langmuir’s isotherm. The inhibition efficiency increased with increase in the concentration of all tested inhibitors to attain a maximum value at 1.0%. Free energy values for adsorption process show that the process is spontaneous. The kinetic treatment of the results shows first order kinetics.

Effect of aliphatic, monocarboxylic, dicarboxylic, heterocyclic and sulphur-containing amino acids on Leishmania spp. chemotaxis.

Science.gov (United States)

Diaz, E; Zacarias, A K; Pérez, S; Vanegas, O; Köhidai, L; Padrón-Nieves, M; Ponte-Sucre, A

2015-11-01

In the sand-fly mid gut, Leishmania promastigotes are exposed to acute changes in nutrients, e.g. amino acids (AAs). These metabolites are the main energy sources for the parasite, crucial for its differentiation and motility. We analysed the migratory behaviour and morphological changes produced by aliphatic, monocarboxylic, dicarboxylic, heterocyclic and sulphur-containing AAs in Leishmania amazonensis and Leishmania braziliensis and demonstrated that L-methionine (10-12 m), L-tryptophan (10-11 m), L-glutamine and L-glutamic acid (10-6 m), induced positive chemotactic responses, while L-alanine (10-7 m), L-methionine (10-11 and 10-7 m), L-tryptophan (10-11 m), L-glutamine (10-12 m) and L-glutamic acid (10-9 m) induced negative chemotactic responses. L-proline and L-cysteine did not change the migratory potential of Leishmania. The flagellum length of L. braziliensis, but not of L. amazonensis, decreased when incubated in hyperosmotic conditions. However, chemo-repellent concentrations of L-alanine (Hypo-/hyper-osmotic conditions) and L-glutamic acid (hypo-osmotic conditions) decreased L. braziliensis flagellum length and L-methionine (10-11 m, hypo-/hyper-osmotic conditions) decreased L. amazonensis flagellum length. This chemotactic responsiveness suggests that Leishmania discriminate between slight concentration differences of small and structurally closely related molecules and indicates that besides their metabolic effects, AAs play key roles linked to sensory mechanisms that might determine the parasite's behaviour.

An evaluation of ambient sulphur dioxide concentrations from passive degassing of the Sulphur Springs, Saint Lucia geothermal system: Implications for human health

Science.gov (United States)

Joseph, Erouscilla P.; Beckles, Denise M.; Cox, Leonette; Jackson, Viveka B.; Alexander, Dominic

2015-10-01

Sulphur Springs Park in Saint Lucia is a site of energetic geothermal activity associated with the potentially active Soufrière Volcanic Centre. The Park is one of Saint Lucia's most important tourist attractions, and is marketed as the 'world's only drive-in volcano'. It has an on-site staff of tour guides and vendors, as well as over 200,000 visitors annually. There are also a number of residents living in the areas bordering the Park. Recreational use is made of the geothermal waters for bathing, application of mud masques, and in some cases drinking. As part of the University of the West Indies, Seismic Research Centre's (UWI-SRC's) overall volcano monitoring programme for Saint Lucia, the volcanic emissions at Sulphur Springs (hot springs, mud pools and fumaroles) have been regularly monitored since 2001. In recent years, visitors, staff, and management at the Park have expressed concern about the health effects of exposure to volcanic emissions from the hydrothermal system. In response to this, SRC has expanded its regular geothermal monitoring programme to include a preliminary evaluation of ambient sulphur dioxide (SO2) concentrations in and around the Park, to assess the possible implications for human health. Passive diffusion tubes were used to measure the atmospheric SO2 concentrations at various sites in Sulphur Springs Park (SSP), in the town of Soufrière and in the capital of Castries. Measurements of average monthly ambient SO2 with the passive samplers indicated that during the dry season period of April to July 2014 concentration at sites closest to the main vents at SSP (Group 1), which are routinely used by staff and visitors, frequently exceeded the WHO 10-minute AQG for SO2 of 500 μg/m3. However, for sites that were more distal to the main venting area (Groups 2 and 3), the average monthly ambient SO2 did not exceed the WHO 10-minute AQG for SO2 of 500 μg/m3 during the entire monitoring period. The measured concentrations and dispersion

Optimization of the 3-Point Bending Failure of Anodized Aluminum Formed in Tartaric/Sulphuric Acid Using Doehlert Design

Science.gov (United States)

Bensalah, W.; Feki, M.; De-Petris Wery, M.; Ayedi, H. F.

2015-02-01

The bending failure of anodized aluminum in tartaric/sulphuric acid bath was modeled using Doehlert design. Bath temperature, anodic current density, sulphuric acid, and tartaric acid concentrations were retained as variables. Thickness measurements and 3-point bending experiments were conducted. The deflection at failure ( D f) and the maximum load ( F m) of each sample were, then, deducted from the corresponding flexural responses. The treatment of experimental results has established mathematical models of second degree reflecting the relation of cause and effect between the factors and the studied properties. The optimum path study of thickness, deflection at failure, and maximum load, showed that the three optima were opposite. Multicriteria optimization using the desirability function was achieved in order to maximize simultaneously the three responses. The optimum conditions were: C tar = 18.2 g L-1, T = 17.3 °C, J = 2.37 A dm-2, C sul = 191 g L-1, while the estimated response values were e = 57.7 µm, D f = 5.6 mm, and F m = 835 N. Using the established models, a mathematical correlation was found between deflection at failure and thickness of the anodic oxide layer. Before bending tests, aluminum oxide layer was examined by scanning electron microscopy (SEM) and atomic force microscopy. After tests, the morphology and the composition of the anodic oxide layer were inspected by SEM, optical microscopy, and glow-discharge optical emission spectroscopy.

Investigating the significance of zero-point motion in small molecular clusters of sulphuric acid and water

International Nuclear Information System (INIS)

Stinson, Jake L.; Ford, Ian J.; Kathmann, Shawn M.

2014-01-01

The nucleation of particles from trace gases in the atmosphere is an important source of cloud condensation nuclei, and these are vital for the formation of clouds in view of the high supersaturations required for homogeneous water droplet nucleation. The methods of quantum chemistry have increasingly been employed to model nucleation due to their high accuracy and efficiency in calculating configurational energies; and nucleation rates can be obtained from the associated free energies of particle formation. However, even in such advanced approaches, it is typically assumed that the nuclei have a classical nature, which is questionable for some systems. The importance of zero-point motion (also known as quantum nuclear dynamics) in modelling small clusters of sulphuric acid and water is tested here using the path integral molecular dynamics method at the density functional level of theory. The general effect of zero-point motion is to distort the mean structure slightly, and to promote the extent of proton transfer with respect to classical behaviour. In a particular configuration of one sulphuric acid molecule with three waters, the range of positions explored by a proton between a sulphuric acid and a water molecule at 300 K (a broad range in contrast to the confinement suggested by geometry optimisation at 0 K) is clearly affected by the inclusion of zero point motion, and similar effects are observed for other configurations

Interactions of meteoric smoke particles with sulphuric acid in the Earth's stratosphere

Directory of Open Access Journals (Sweden)

R. W. Saunders

2012-05-01

Full Text Available Nano-sized meteoric smoke particles (MSPs with iron-magnesium silicate compositions, formed in the upper mesosphere as a result of meteoric ablation, may remove sulphuric acid from the gas-phase above 40 km and may also affect the composition and behaviour of supercooled H₂SO₄-H₂O droplets in the global stratospheric aerosol (Junge layer.

This study describes a time-resolved spectroscopic analysis of the evolution of the ferric (Fe³⁺ ion originating from amorphous ferrous (Fe²⁺-based silicate powders dissolved in varying Wt % sulphuric acid (30–75 % solutions over a temperature range of 223–295 K. Complete dissolution of the particles was observed under all conditions. The first-order rate coefficient for dissolution decreases at higher Wt % and lower temperature, which is consistent with the increased solution viscosity limiting diffusion of H₂SO₄ to the particle surfaces. Dissolution under stratospheric conditions should take less than a week, and is much faster than the dissolution of crystalline Fe²⁺ compounds.

The chemistry climate model UMSLIMCAT (based on the UKMO Unified Model was then used to study the transport of MSPs through the middle atmosphere. A series of model experiments were performed with different uptake coefficients. Setting the concentration of 1.5 nm radius MSPs at 80 km to 3000 cm⁻³ (based on rocket-borne charged particle measurements, the model matches the reported Wt % Fe values of 0.5–1.0 in Junge layer sulphate particles, and the MSP optical extinction between 40 and 75 km measured by a satellite-borne spectrometer, if the global meteoric input rate is about 20 tonnes per day. The model indicates that an uptake coefficient ≥0.01 is required to account for the observed two orders of magnitude depletion of H₂SO₄ vapour above 40 km.

Steam reforming of commercial ultra-low sulphur diesel

Energy Technology Data Exchange (ETDEWEB)

Boon, J.; Van Dijk, E.; De Munck, S.; Van den Brink, R. [Energy research Centre of The Netherlands, ECN Hydrogen and Clean Fossil Fuels, P.O. Box 1, NL1755ZG Petten (Netherlands)

2011-03-11

Two main routes for small-scale diesel steam reforming exist: low-temperature pre-reforming followed by well-established methane steam reforming on the one hand and direct steam reforming on the other hand. Tests with commercial catalysts and commercially obtained diesel fuels are presented for both processes. The fuels contained up to 6.5 ppmw sulphur and up to 4.5 vol.% of biomass-derived fatty acid methyl ester (FAME). Pre-reforming sulphur-free diesel at around 475C has been tested with a commercial nickel catalyst for 118 h without observing catalyst deactivation, at steam-to-carbon ratios as low as 2.6. Direct steam reforming at temperatures up to 800C has been tested with a commercial precious metal catalyst for a total of 1190 h with two catalyst batches at steam-to-carbon ratios as low as 2.5. Deactivation was neither observed with lower steam-to-carbon ratios nor for increasing sulphur concentration. The importance of good fuel evaporation and mixing for correct testing of catalysts is illustrated. Diesel containing biodiesel components resulted in poor spray quality, hence poor mixing and evaporation upstream, eventually causing decreasing catalyst performance. The feasibility of direct high temperature steam reforming of commercial low-sulphur diesel has been demonstrated.

Steam reforming of commercial ultra-low sulphur diesel

Science.gov (United States)

Boon, Jurriaan; van Dijk, Eric; de Munck, Sander; van den Brink, Ruud

Two main routes for small-scale diesel steam reforming exist: low-temperature pre-reforming followed by well-established methane steam reforming on the one hand and direct steam reforming on the other hand. Tests with commercial catalysts and commercially obtained diesel fuels are presented for both processes. The fuels contained up to 6.5 ppmw sulphur and up to 4.5 vol.% of biomass-derived fatty acid methyl ester (FAME). Pre-reforming sulphur-free diesel at around 475 °C has been tested with a commercial nickel catalyst for 118 h without observing catalyst deactivation, at steam-to-carbon ratios as low as 2.6. Direct steam reforming at temperatures up to 800 °C has been tested with a commercial precious metal catalyst for a total of 1190 h with two catalyst batches at steam-to-carbon ratios as low as 2.5. Deactivation was neither observed with lower steam-to-carbon ratios nor for increasing sulphur concentration. The importance of good fuel evaporation and mixing for correct testing of catalysts is illustrated. Diesel containing biodiesel components resulted in poor spray quality, hence poor mixing and evaporation upstream, eventually causing decreasing catalyst performance. The feasibility of direct high temperature steam reforming of commercial low-sulphur diesel has been demonstrated.

Tracer study on sulphur use efficiency in potato-barley sequence on acid soil of Shimla

International Nuclear Information System (INIS)

Sud, K.C.; Sharma, R.C.; Sharma, N.K.

1999-01-01

Controlled studies were conducted on acidic soil of Fagu (Shimla) to study the efficiency of labelled ammonium sulphate as effected by farmyard manure (FYM) on potato (Solanum tuberosum L.) and its residual effect on succeeding barley (Hordeum vulgare L.). The direct and residual effects of FYM and sulphur on dry matter yield and S concentration in potato and barley plants were significant. Applied FYM had a positive effect on radioassay values i.e. % Sdff and % S utilization by potato from labelled S carrier, whereas, the residual effect of applied S on barley was more than its direct effect on potato. Results indicate that combined application of S and FYM resulted in 3.4 per cent more S contribution to barley crop and was reflected in % S utilization values. (author)

The role of phosphate additive in stabilization of sulphuric-acid-based vanadium(V) electrolyte for all-vanadium redox-flow batteries

Science.gov (United States)

Roznyatovskaya, Nataliya V.; Roznyatovsky, Vitaly A.; Höhne, Carl-Christoph; Fühl, Matthias; Gerber, Tobias; Küttinger, Michael; Noack, Jens; Fischer, Peter; Pinkwart, Karsten; Tübke, Jens

2017-09-01

Catholyte in all-vanadium redox-flow battery (VRFB) which consists of vanadium salts dissolved in sulphuric acid is known to be stabilized by phosphoric acid to slow down the thermal aging at temperatures higher than 40 °C. To reveal the role of phosphoric acid, the thermally-induced aggregation is investigated using variable-temperature 51V, 31P, 17O, 1H nuclear magnetic resonance (NMR) spectroscopy and dynamic light scattering (DLS). The results indicate that the thermal stabilization of vanadium(V) electrolyte is attained by the involvement of monomeric and dimeric vanadium(V) species in the reaction with phosphoric acid which is concurrent to the formation of neutral hydroxo-aqua vanadium(V) precipitation precursor. The dimers are stabilized by counter ions due to association reaction or if such stabilization is not possible, precipitation of vanadium pentoxide is favored. The evolution of particles size distributions at 50 °C in electrolyte samples containing 1.6 M vanadium and 4.0 M total sulphate and the pathways of precipitate formation are discussed. The optimal total phosphate concentration is found to be of 0.15 M. However, the induction time is assumed to be dependent not only on the total phosphate concentrations, but also on the ratio of total vanadium(V) to sulphate concentrations.

Effects of sulphur ion implantation on the electrochemical behaviour of two stainless steels in sulphuric medium

International Nuclear Information System (INIS)

Nader-Roux, J.; Becdelievre, A.M. de; Gaillard, F.; Roux, R.; Becdelievre, J. de

1986-01-01

The electrochemical behaviour in sulphuric acid of two austenitic stainless steels (AISI 304 L and AISI 321) modified by sulphur ion implantation has been studied. Surface analysis of oxygen and sulphur by LEEIXS and XRFS were performed before and after polarization on unimplanted and on implanted samples. I/E curves with implanted steels reveal an important corrosion peak (α peak) recovering widely the active peak of unimplanted samples. For high implanted doses, another peak (β peak) appears in the passive range. High doses implanted steels polarized in the range of the α peak exhibit a sulphur enriched black surface layer. SEM examination of this layer shows it is constituted by flakes rolling up themselves. The formation of a superficial non-protective sulphide layer and the internal stresses of this layer explain the corrosion enhancement of sulphur implanted materials. After dissolution of this layer the behaviour of unimplanted steels is found again. (author)

Enhancement of the Inhibitor Efficiency of Atropine Methochloride in Corrosion Control of Mild Steel in Sulphuric Acid

Directory of Open Access Journals (Sweden)

Abida Begum

2008-01-01

Full Text Available The inhibition efficiency and synergistic behaviour of 10-4 M Atropine methochloride was carried out using mass loss and polarisation methods in the presence of (i metal ions, Ni2+ and Cu2+ between 10-2 M to 10-6 M concentrations, (ii different concentrations of metal ions and 10-3 M I-, 10-3 M Cl- and 10-3 M Br- solutions and (iii different metal ions, 10-3M I- and at three different temperatures. The analysis reveals that the inhibition efficiency of Atropine methochloride was maximum at 10-2 M in 5 hours of immersion period. Halides decreased the corrosion rate of mild steel in Sulphuric acid. The decrease is maximum with 10-3 M I-. As the temperature increased from 298K to 308K, the inhibition efficiency gradually decreased. The inhibitor was found to be effective up to 303K

Influence of molybdate species on the tartaric acid/sulphuric acid anodic films grown on AA2024 T3 aerospace alloy

Energy Technology Data Exchange (ETDEWEB)

Garcia-Rubio, M. [Departamento de Quimica-Fisica Aplicada, Universidad Autonoma de Madrid, 28049 Madrid (Spain); Department of Surface Technologies, Engineering of Materials and Processes, Airbus Spain, Av. John Lennon s/n 28906 Getafe (Spain); Ocon, P. [Departamento de Quimica-Fisica Aplicada, Universidad Autonoma de Madrid, 28049 Madrid (Spain)], E-mail: pilar.ocon@uam.es; Climent-Font, A. [Departamento de Fisica Aplicada, Universidad Autonoma de Madrid (UAM), 28049 Madrid (Spain); Centro de Micro-Analisis de Materiales (CMAM), Universidad Autonoma de Madrid (UAM), 28049 Madrid (Spain); Smith, R.W. [Unidad de Microanalisis de Materiales, Parque Cientifico de Madrid (PCM), Campus de Cantoblanco, 28049 Madrid (Spain); Curioni, M.; Thompson, G.E.; Skeldon, P. [Corrosion and Protection Centre, School of Materials, University of Manchester, M60 1QD England (United Kingdom); Lavia, A.; Garcia, I. [Department of Surface Technologies, Engineering of Materials and Processes, Airbus Spain, Av. John Lennon s/n 28906 Getafe (Spain)

2009-09-15

AA2024 T3 alloy specimens have been anodised in tartaric acid/sulphuric media and tartaric acid/sulphuric media containing sodium molybdate; molybdate species were added to the anodising bath to enhance further the protection provided by the porous anodic film developed over the macroscopic alloy surface. Morphological characterisation of the anodic films formed in both electrolytes was undertaken using scanning electron and transmission electron microscopies; the chemical compositions of the films were determined by Rutherford backscattering spectroscopy that was complemented by elemental depth profiling using rf-glow discharge optical emission spectrometry. The electrochemical behaviour was evaluated using potentiodynamic polarisations and electrochemical impedance spectroscopy; the corrosion performance was examined after salt spray testing. The porous anodic film morphology was little influenced by the addition of molybdate salt, although thinner films were generated in its presence. Chemical composition of the anodic film was roughly similar; however, addition of sodium molybdate in the anodizing bath resulted in residues of molybdate species in the porous skeleton and improved corrosion resistance measured by electrochemical techniques that was confirmed by salt spray testing.

Influence of molybdate species on the tartaric acid/sulphuric acid anodic films grown on AA2024 T3 aerospace alloy

International Nuclear Information System (INIS)

Garcia-Rubio, M.; Ocon, P.; Climent-Font, A.; Smith, R.W.; Curioni, M.; Thompson, G.E.; Skeldon, P.; Lavia, A.; Garcia, I.

2009-01-01

AA2024 T3 alloy specimens have been anodised in tartaric acid/sulphuric media and tartaric acid/sulphuric media containing sodium molybdate; molybdate species were added to the anodising bath to enhance further the protection provided by the porous anodic film developed over the macroscopic alloy surface. Morphological characterisation of the anodic films formed in both electrolytes was undertaken using scanning electron and transmission electron microscopies; the chemical compositions of the films were determined by Rutherford backscattering spectroscopy that was complemented by elemental depth profiling using rf-glow discharge optical emission spectrometry. The electrochemical behaviour was evaluated using potentiodynamic polarisations and electrochemical impedance spectroscopy; the corrosion performance was examined after salt spray testing. The porous anodic film morphology was little influenced by the addition of molybdate salt, although thinner films were generated in its presence. Chemical composition of the anodic film was roughly similar; however, addition of sodium molybdate in the anodizing bath resulted in residues of molybdate species in the porous skeleton and improved corrosion resistance measured by electrochemical techniques that was confirmed by salt spray testing.

Ergo betters estimates after shaky first years. [Recovery of gold, uranium and sulphuric acid

Energy Technology Data Exchange (ETDEWEB)

1982-05-20

Having completed its fourth year of full operation, East Rand Gold and Uranium (ERGO) has established itself as a succesful low-cost gold producer. The recovering of gold, uranium and sulphuric acid from some old slimes dams has beaten its production estimates for 1981 till the end of March 1982. Overall Ergo has settled down well from its first years of production.

Development of the floating sulphur biofilm reactor for sulphide ...

African Journals Online (AJOL)

Development of the floating sulphur biofilm reactor for sulphide oxidation in biological water treatment systems. ... The effect of influent sulphide concentrations, flow rate and reactor dimensions on the sulphur biofilm formation were investigated for the optimisation of elemental sulphur recovery and sulphide removal ...

Evaluation of modified atmosphere bag and sulphur dioxide concentrations applied on highbush blueberries fruit (Vaccinium corymbosum L.) cv. Emerald

OpenAIRE

Rodríguez, Mario; Wyss, Anddy; Hormazábal, Nelson

2015-01-01

Aiming to evaluate techniques for modified atmosphere and application of sulphur anhydride upon parameters of quality of postharvest on blueberry fruit (Vaccinium corymbosum L.) cv. Emerald, an experiment of six treatments was conducted, given by the combination of two factors, modified atmosphere (with and without) and different concentrations of sulphur dioxide (generated by 0, 1 and 2 g of sodium metabisulphite) during 7, 14, 21 and 28 days at 0 °C. The dose of 2 g of modified atmosphere s...

Extraction mechanism of Sc(III) from sulphuric acid solution by primary amine N1923

International Nuclear Information System (INIS)

Le Shaoming; Li Deqian; Ni Jiazan

1987-01-01

The extraction mechanism of Sc(III) from sulphuric acid solution by primary amine N 1923 (RNH 2 ) has been investigated by means of slope, isomolar continuous variation and saturation methods. The effect of temperature on the extraction of Sc(III) is observed. The extraction equilibrium constant and thermodynamic functions (ΔH, ΔS and ΔG) are obtained. The IR and NMR of extracted compound are measured

Enhanced high temperature thermoelectric response of sulphuric acid treated conducting polymer thin films

KAUST Repository

Sarath Kumar, S. R.; Kurra, Narendra; Alshareef, Husam N.

2015-01-01

We report the high temperature thermoelectric properties of solution processed pristine and sulphuric acid treated poly(3, 4-ethylenedioxythiophene):poly(4-styrenesulfonate) (or PEDOT:PSS) films. The acid treatment is shown to simultaneously enhance the electrical conductivity and Seebeck coefficient of the metal-like films, resulting in a five-fold increase in thermoelectric power factor (0.052 W/m. K ) at 460 K, compared to the pristine film. By using atomic force micrographs, Raman and impedance spectra and using a series heterogeneous model for electrical conductivity, we demonstrate that acid treatment results in the removal of PSS from the films, leading to the quenching of accumulated charge-induced energy barriers that prevent hopping conduction. The continuous removal of PSS with duration of acid treatment also alters the local band structure of PEDOT:PSS, resulting in simultaneous enhancement in Seebeck coefficient.

Enhanced high temperature thermoelectric response of sulphuric acid treated conducting polymer thin films

KAUST Repository

Sarath Kumar, S. R.

2015-11-24

We report the high temperature thermoelectric properties of solution processed pristine and sulphuric acid treated poly(3, 4-ethylenedioxythiophene):poly(4-styrenesulfonate) (or PEDOT:PSS) films. The acid treatment is shown to simultaneously enhance the electrical conductivity and Seebeck coefficient of the metal-like films, resulting in a five-fold increase in thermoelectric power factor (0.052 W/m. K ) at 460 K, compared to the pristine film. By using atomic force micrographs, Raman and impedance spectra and using a series heterogeneous model for electrical conductivity, we demonstrate that acid treatment results in the removal of PSS from the films, leading to the quenching of accumulated charge-induced energy barriers that prevent hopping conduction. The continuous removal of PSS with duration of acid treatment also alters the local band structure of PEDOT:PSS, resulting in simultaneous enhancement in Seebeck coefficient.

Recovery of uranium in the production of concentrated phosphoric acid by a hemihydrate process

International Nuclear Information System (INIS)

Nakajima, S.; Miyamoto, M.

1983-01-01

Nissan Chemical Industries as manufacturers of phosphoric acid have studied the recovery of uranium, based on a concentrated phosphoric acid production process. The process consists of two stages, a hemihydrate stage with a formation of hemihydrate and a filtration section, followed by a dihydrate stage with hydration and a filtration section. In the hemihydrate stage, phosphate is treated with a mixture of phosphoric acid and sulphuric acid to produce phosphoric acid and hydrous calcium sulphate; the product is recovered in the filtration section and its concentration is 40-50% P 2 O 3 . In the dihydrate stage, the hemihydrate is transformed by re-dissolution and hydration, producing hydrous calcium sulphate, i.e. gypsum. This process therefore comprises two parts, each with different acid concentrations. As the extraction of uranium is easier in the case of a low concentration of phosphoric acid, the process consists of the recovery of uranium starting from the filtrate of the hydration section. The tests have shown that the yield of recovery of uranium was of the order of 80% disregarding the handling losses and no disadvantageous effect has been found in the combination of the process of uranium extraction with the process of concentrated phosphoric acid production. Compared with the classical process where uranium is recovered from acid with 30% P 2 O 5 , the process of producing high-concentration phosphoric acid such as the Nissan process, in which the uranium recovery is effected from acid with 15% P 2 O 5 from the hydration section, presents many advantages [fr

Kinetics and thermodynamics of aluminium dissolution in 1.0M sulphuric acid containing chloride ions

Energy Technology Data Exchange (ETDEWEB)

Abdel-Gaber, A.M. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt)]. E-mail: ashrafmoustafa@yahoo.com; Abd-El-Nabey, B.A. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt); Sidahmed, I.M. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt); El-Zayady, A.M. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt); Saadawy, M. [Department of Chemistry, Faculty of Science, Alexandria University, P.O. Box 426, Ibrahimia, Alexandria 21321 (Egypt)

2006-08-01

The dissolution of aluminium in 1M sulphuric acid solutions containing different chloride ion concentrations (0.01-0.06M) were studied at 25, 30, 35 and 40deg. C using electrochemical impedance spectroscopy (EIS) technique and polarization curves measurements. The kinetic rate equation, under the experimental condition described, was derived and found to verify the following relationship:V=k{sub obs}K{sub 2}C{sub Cl{sup -}}{sup n}1+K{sub 2}C{sub Cl{sup -}}{sup n}where V is the corrosion rate, k{sub obs} and K{sub 2} are the dissolution rate constant of aluminium oxide-chloride complex and the equilibrium constant of chloride ions adsorbed at aluminium oxide surface, respectively. The kinetic and thermodynamic energy parameters were calculated and their values indicate that chloride ions are chemisorbed onto the aluminium oxide surface and the formation of oxide-chloride complex is the rate-determining step.

Total vs. internal element concentrations in Scots pine needles along a sulphur and metal pollution gradient

International Nuclear Information System (INIS)

Rautio, Pasi; Huttunen, Satu

2003-01-01

Different methods should be used for foliar analyses of trees used as bioindicators of pollution, than those analyses used in nutritional studies of trees. - Analysis of foliar elements is a commonly used method for studying tree nutrition and for monitoring the impacts of air pollutants on forest ecosystems. Interpretations based on the results of foliar element analysis may, however, be different in nutrition vs. monitoring studies. We studied the impacts of severe sulphur and metal (mainly Cu and Ni) pollution on the element concentrations (Al, Ca, Cu, Fe, K, Mg, Mn, Ni, P, Pb, S and Zn) in Scots pine (Pinus sylvestris L.) foliage along an airborne sulphur and metal pollution gradient. Emphasis was put on determining the contribution of air-borne particles that have accumulated on needle surfaces to the total foliage concentrations. A comparison of two soil extraction methods was carried out in order to obtain a reliable estimate of plant-available element concentrations in the soil. Element concentrations in the soil showed only a weak relationship with internal foliar concentrations. There were no clear differences between the total and internal needle S concentrations along the gradient, whereas at the plot closest to the metal smelter complex the total Cu concentrations in the youngest needles were 1.3-fold and Ni concentrations over 1.6-fold higher than the internal needle concentrations. Chloroform-extracted surface wax was found to have Ni and Cu concentrations of as high as 3000 and 600 μg/g of wax, respectively. Our results suggest that bioindicator studies (e.g. monitoring studies) may require different foliar analysis techniques from those used in studies on the nutritional status of trees

Sulphur output from oil sands : dramatically changing Alberta's sulphur balance

International Nuclear Information System (INIS)

D'Aquin, G.

2008-01-01

This paper discussed sulphur production from Alberta's gas and oil sands industries. While sulfur derived from natural gas production in the province is expected to decline as natural gas reserves diminish, Alberta's oil sands contain high amounts of sulphur. It is not yet known how much sulphur will be produced from the province's oil sands facilities. Alberta had considerable stockpiles of sulphur in the 1970s. By 1980, inventories began to decline. By 1996, output had increased to 7.1 million tonnes. Alberta's sulphur inventory reached 9.7 million tonnes following the collapse of the Soviet Union's government mandated fertilizer industry. In 2006, sulphur supplies in Alberta reached 12 million tonnes. Reduced global output has now lowered sulphur stockpiles. Increases in sulphur prices tend to reduce market demand, and lower prices will not typically change the volume of sulphur produced as a byproduct of oil and gas operations. Bitumen-derived sulphur output is expected to exceed gas-derived sulphur output in the near future. Sulphur from oil sands processing is expected to increase by 5 million tonnes by 2017. Increased sulphur production levels in Alberta will present a significant challenge for all sectors of the hydrocarbon industry. It was concluded that developing a plan for storing, selling or disposing of the sulphur will help to ensure the profitability of oil sands operations

Sumpor u ugljenu (Sulphur in Coal

Directory of Open Access Journals (Sweden)

Rađenović, A.

2004-12-01

utilisation of coals with low sulphur concentrations (typically < 1 wt %, the removal of cleaning prior to utilisation. The methods for the removal of sulphur from coal can be divided into: physical, chemical and microbiological. The mineral sulphur components can be removed or reduced by commercial methods of coal washing, flotation and agglomeration. A number of chemical desulphurization for the removal of, both, pyritic and organic sulphur have been advocated. The chemical desulphurization methods however, have two major drawbacks. Namely, they are often expensive and they destroy the caking properties of coal. Certain microorganisms have been used to consume or convert selectively most of the pyritic sulphur as well as some of the organic sulphur in coal. The process is also cheaper than chemical desulphurization and does not affect the caking properties of coking coal.

Multistage dilute acid leaching of a medium grade iron ore to super-concentrate

Directory of Open Access Journals (Sweden)

Adeleke A.A.

2014-01-01

Full Text Available The phosphorous laden Koton Karfe iron ore is a medium grade iron ore deposit in Nigeria that can be upgraded as a super-concentrate for use at the Aladja Steel Midrex plant. The 75 μm size sample fraction of the ore was preconcentrated with shaking table and leached in the oven at atmospheric pressure with dilute hydrochloric acid in single and multistage leaching sequences of H2O-HCl-H2O and HCl-H2O-H2O. The as-received, as-tabled and asleached samples were then subjected to X-ray fluorescence and microscopic analyses. The results obtained showed that the H2O-HCl-H2O route produced a higher grade concentrate that assayed 68.54% Fe indicating about 58% upgrade in iron content; while the phosphorus and sulphur contents were reduced by about 77 and 99.6% respectively. In addition, the silicon, manganese, and titanium contents were drastically reduced, while potassium was completely eliminated. The upgrade of iron content in the ore to 68.54% and the drastic reduction in phosphorous and sulphur contents has thus rendered the Koton Karfe iron ore suitable for use as a super concentrate for the Aladja steel plant direct reduction iron making process.

The effects of added sulphur amino acids, threonine and an ideal amino acid ratio on nitrogen metabolism in mature, overweight dogs.

Science.gov (United States)

Bohaty, Robin E; de Godoy, Maria R C; McLeod, Kyle R; Harmon, David L

2012-02-01

The objectives of this study were to investigate the effects of added essential amino acids in conjunction with a dietary lysine/MJ of 0.72 on nitrogen (N) metabolism in dogs. Treatments were; a control diet, a diet that provided an ideal amino acid profile (IAA), a diet with added total sulphur amino acids (TSAA), and a diet with added TSAA and threonine (TT). Diets were fed to eight overweight, mature, female hounds using a replicated 4 x 4 Latin Square design. Food intake was similar across treatments, however, food N intake was higher (p dogs formulated to provide a 0.72 g lysine/MJ ME ratio.

Study of the sulfuric acid leaching and bacterial leaching of low grade uranium ore by orbital shaker experiment

International Nuclear Information System (INIS)

Li Guangyue; Liu Yulong; Wang Yongdong; Ding Dexin

2009-01-01

The sulphuric acid leaching and bacteria leaching by orbital shaker experiments were conducted for the low grade uranium ore from a uranium mine in Guangdong Province. The results show that, when the concentration of sulphuric acid and that of slurry were 30 g/L and 25%, respectively, the conditions were most favourable for sulphuric acid leaching and the rate of leaching reached 92.92%, that, when pH value was 1.5, inoculation amount, 10%, concentration of slurry, 10%, the conditions were most favourable for bacteria leaching and the rate of leaching reached 95.93%, that, compared with sulphuric acid leaching, bacteria leaching decreased sulphuric acid consumption by 17.2% and increased the rate of leaching by 3%, and that, under the most favourable conditions for suphuric acid leaching, if 1% natrium chlorate was added, the rate of leaching increased to 96.46%, but 10 kg of natrium chlorate was consumed for 1 ton of uranium ore. (authors)

Concentration of volatile sulphur-containing compounds along the gastrointestinal tract of pigs fed a high-sulphur or a low-sulphur diet

DEFF Research Database (Denmark)

Poulsen, Henrik Vestergaard; Canibe, Nuria; Finster, Kai

2010-01-01

Volatile sulphur-containing compounds (VSC) are formed in large quantities in the gastrointestinal tract (GI-tract) of pigs and upon excretion from the animal; these compounds are released from the faeces causing emission of foul odour. However, very little is known about the rate and extent of t...

Sulphur in Poland

Directory of Open Access Journals (Sweden)

Seman Peter

2001-12-01

Full Text Available Poland belongs to one of the last countries with native sulphur mining. Its history begun in 15th century. Deposit area of Tarnobrzeg re-presents 80% of all known sulphur reserves in this country. All of explored deposits in this area were created by metasomatic alteration of sulphur bearing limestones with sulphur mineralised liquids, which arised from melt gypsum. The average content is 25 - 30% of sulphur in Tarnobrzeg area. Considerable parts of deposits are created by calcite and native sulphur. Gypstone, baryte and stroncianite have only minera-logic occurencies. The extensive native sulphur deposits account for 88% of the country´s sulphur production. There were five sulphur mines in operation: Jeziórko, Grêbów, Machów I, Machów II and Basznia, but operations in Basznia were ended in 1992 and Machów and Machów II were liquidated. The sixth mine Osiek is currently producing. Only the Machów I mine operated an open-pit extraction and refining process, the other four mines producing sulphur using a modified Frasch method that gives elemental sulphur of up to 99,9% purity. Sulphur is an important export commodity with foreign sales totalling around 1.5 - 2.5 Mt/y. Modern benefication methods, which allowing to achieve sulphur from hydrocarbons, are causing decrease of native sulphur prices in the world and bringing about reduction of mining activities for this raw material in Poland.

Effective closed form mathematical approach to determine kinetic constants of NR vulcanized with sulphur and accelerators at different concentrations

Energy Technology Data Exchange (ETDEWEB)

Milani, Gabriele, E-mail: milani@stru.polimi.it, E-mail: gabriele.milani@polimi.it [Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milan (Italy); Hanel, Thomas; Donetti, Raffaella [Pirelli Tyre, Via Alberto e Piero Pirelli 25, 20126 Milan (Italy); Milani, Federico [CHEMCO Consultant, Via J.F. Kennedy 2, 45030 Occhiobello (Italy)

2015-03-10

The basic reaction scheme due to Han and co-workers for NR vulcanized with sulphur is adopted and modified taking into account the single contributions of the different accelerators, focusing in particular on some experimental data ad hoc obtained at Pirelli’s laboratories, where NR was vulcanized at different temperatures (from 150 to 180 °C) and concentrations of sulphur, using TBBS and DPG in the mixture as co-agents. Typically, the chain reactions are initiated by the formation of macro-compounds that are responsible of the formation of the unmatured crosslinked polymer. This first reaction depends on the reciprocal concentrations of all components and their chemical nature. In presence of two accelerators, it was considered that the reactions between each single accelerator and the NR raw material occur in parallel, making the reasonable assumption that there are no mutual reactions between the two accelerators. From the kinetic scheme adopted, a closed form solution was found for the crosslink density, with the only limitation that the induction period is excluded from computations. Even kinetic constants are evaluated in closed form, avoiding a numerically demanding least-squares best fitting on rheometer experimental data. Two series of experiments available, relying into rheometer curves at different temperatures and different concentrations of sulphur and accelerator, are utilized to evaluate the fitting capabilities of the mathematical model. Very good agreement between numerical output and experimental data is experienced in all cases analysed.

Concerning the acid dew point in waste gases from combustion processes

Energy Technology Data Exchange (ETDEWEB)

Knoche, K.F.; Deutz, W.; Hein, K.; Derichs, W.

1986-09-01

The paper discusses the problems associated with the measurement of acid dew point and of sulphuric acid-(say SO/sub 3/-)concentrations in the flue gas from brown coal-fired boiler plants. The sulphuric acid content in brown coal flue gas has been measured at 0.5 to 3 vpm in SO/sub 2/ concentrations of 200 to 800 vpm. Using a conditional equation, the derivation of which from new formulae for phase stability is described in the paper, an acid dew point temperature of 115 to 125/sup 0/C is produced.

Sulphur levels in saliva as an estimation of sulphur status in cattle: a validation study

NARCIS (Netherlands)

Dermauw, V.; Froidmont, E.; Dijkstra, J.; Boever, de J.L.; Vyverman, W.; Debeer, A.E.; Janssens, G.P.J.

2012-01-01

Effective assessment of sulphur (S) status in cattle is important for optimal health, yet remains difficult. Rumen fluid S concentrations are preferred, but difficult to sample under practical conditions. This study aimed to evaluate salivary S concentration as estimator of S status in cattle.

Solving the sulphur situation : research assesses viability of burying sulphur

International Nuclear Information System (INIS)

Proce, B.

2006-01-01

Oil sands mining companies are looking for ways to manage growing levels of sulphur production from the Athabasca region. Infrastructure is not in place to economically transport the sulphur even though there is a global market for it. Sulphur cannot be stockpiled indefinitely as it can react with air to produce sulphur dioxide. Although above-ground sulphur storage has been regulated for more than 30 years, the underground storage of sulphur is still in a research and development phase. Alberta Sulphur Research Ltd. is currently conducting an ongoing experiment in which 100 tonne test blocks have been buried above and below the water table so that surrounding areas could be monitored over a period of years. A series of tests is being conducted to examine changes in pH in water and sulphate levels. A multi-layered engineering casing to contain the sulphur and prevent seepage is also being investigated. Once stored underground, operators also have to consider how the sulphur will be accessed in the future, as it is subject to government royalties. The storage of sulphur may have economic benefits as the product can be sold when prices are high. Most sulphur produced in Alberta is sold as an export product in the United States for use in products such as fertilizer. Shell Canada penetrated the Chinese market in 2001 and has since become one of Canada's largest sulphur exporters. Shell has also introduced a number of products using sulphur, including fertilizers, enhanced asphalt, and concrete. It was concluded that companies must take action now to mitigate future losses and to utilize current markets in order to remain competitive. 3 figs

Determination of the O/M ratios of polynary uranium oxides by Ce(IV)-Fe(II) back titration after dissolution in mixed sulphuric and phosphoric acids.

Science.gov (United States)

Fujino, T; Sato, N; Yamada, K

1996-01-01

Uranium (IV) in polynary uranium oxides is determined after the solid has been dissolved in a warm mixed solution of sulphuric and phosphoric acids containing excess Ce(IV). The latter is titrated with a Fe(II) standard solution using ferroin as indicator. This method is especially effective for (mixed) uranium oxides which are difficult to dissolve in hot Ce(IV) sulphuric acid. The standard deviation of the determined x value in polynary oxides is estimated to be below +/- 0.004 for samples of 10-30 mg.

Maximum production rate optimization for sulphuric acid decomposition process in tubular plug-flow reactor

International Nuclear Information System (INIS)

Wang, Chao; Chen, Lingen; Xia, Shaojun; Sun, Fengrui

2016-01-01

A sulphuric acid decomposition process in a tubular plug-flow reactor with fixed inlet flow rate and completely controllable exterior wall temperature profile and reactants pressure profile is studied in this paper by using finite-time thermodynamics. The maximum production rate of the aimed product SO 2 and the optimal exterior wall temperature profile and reactants pressure profile are obtained by using nonlinear programming method. Then the optimal reactor with the maximum production rate is compared with the reference reactor with linear exterior wall temperature profile and the optimal reactor with minimum entropy generation rate. The result shows that the production rate of SO 2 of optimal reactor with the maximum production rate has an increase of more than 7%. The optimization of temperature profile has little influence on the production rate while the optimization of reactants pressure profile can significantly increase the production rate. The results obtained may provide some guidelines for the design of real tubular reactors. - Highlights: • Sulphuric acid decomposition process in tubular plug-flow reactor is studied. • Fixed inlet flow rate and controllable temperature and pressure profiles are set. • Maximum production rate of aimed product SO 2 is obtained. • Corresponding optimal temperature and pressure profiles are derived. • Production rate of SO 2 of optimal reactor increases by 7%.

Effect of sulphur forms on colour and residue of sulphur during the storage at drying grapes by sulphur

Directory of Open Access Journals (Sweden)

Boztepe Özlem

2016-01-01

Full Text Available Turkey is the world leader in the manufacture and export of seedless raisins. Requirement of golden bleached raisins is increasing in food Industry of especially cake, bread and pastry year by year. In this research, the lowest residual value and the practical realization of such production was intended to determine by drying grapes with application of sulphur. In this case, sulphur residue and colour situations were determined during 12-mounth-storage according to sulphur forms. In this study sulphur studies were applied by Vitis Vinifera cv. “Sultani Çekirdeksiz” with Na2S2O5, which is liquid source of sulphur and SO2, which is gas source of sulphur. SO2 application were studied during 3, 6 and 8 hours and liquid form of sulphur is Na2S2O5 that was used during by 10, 20 and 30 minutes. Applications were prepared with 3 replicates which contain 20 kg fresh grape in each replicate. In conclusion, changes in dried grape have been identified in point of colour (chroma and hue and the sulphur content was determined according to sulphur forms in packing. Gas form of sulphur (SO2 which was applied 3 hours, gave the best result during 12-mounth-storage for colour and sulphur residue.

Sulphurous Mineral Waters: New Applications for Health

Directory of Open Access Journals (Sweden)

Jose Manuel Carbajo

2017-01-01

Full Text Available Sulphurous mineral waters have been traditionally used in medical hydrology as treatment for skin, respiratory, and musculoskeletal disorders. However, driven by recent intense research efforts, topical treatments are starting to show benefits for pulmonary hypertension, arterial hypertension, atherosclerosis, ischemia-reperfusion injury, heart failure, peptic ulcer, and acute and chronic inflammatory diseases. The beneficial effects of sulphurous mineral waters, sulphurous mud, or peloids made from sulphurous mineral water have been attributed to the presence of sulphur mainly in the form of hydrogen sulphide. This form is largely available in conditions of low pH when oxygen concentrations are also low. In the organism, small amounts of hydrogen sulphide are produced by some cells where they have numerous biological signalling functions. While high levels of hydrogen sulphide are extremely toxic, enzymes in the body are capable of detoxifying it by oxidation to harmless sulphate. Hence, low levels of hydrogen sulphide may be tolerated indefinitely. In this paper, we review the chemistry and actions of hydrogen sulphide in sulphurous mineral waters and its natural role in body physiology. This is followed by an update of available data on the impacts of exogenous hydrogen sulphide on the skin and internal cells and organs including new therapeutic possibilities of sulphurous mineral waters and their peloids.

Electrochemical dissolution of tin in methanesulphonic acid solutions

NARCIS (Netherlands)

de Greef, R.A.T.; Janssen, L.J.J.

2001-01-01

High-rate electroplating of tin on a moving steel strip is generally carried out in cells with dimensionally stable anodes. To obtain a matt tin deposit a concentrated acidic tin methanesulphonate solution containing a small concentration of sulphuric acid is used. The concentrated tin

Determination of the O/M ratios of polynary uranium oxides by Ce(IV)-Fe(II) back titration after dissolution in mixed sulphuric and phosphoric acids

International Nuclear Information System (INIS)

Fujino, T.; Sato, N.; Yamada, K.

1996-01-01

Uranium (IV) in polynary uranium oxides is determined after the solid has been dissolved in a warm mixed solution of sulphuric and phosphoric acids containing excess Ce(IV). The latter is titrated with a Fe(II) standard solution using ferroin as indicator. This method is especially effective for (mixed) uranium oxides which are difficult to dissolve in hot Ce(IV) sulphuric acid. The standard deviation of the determined x value in polynary oxides is estimated to be below ± 0.004 for samples of 10-30 mg. (orig.)

Leaching of a Cu-Co ore from Congo using sulphuric acidhydrogen peroxide leachants

Directory of Open Access Journals (Sweden)

Seo S.Y.

2013-01-01

Full Text Available A Cu-Co ore from Katinga Province, the Republic of Congo containing 1.5% Co and 1.6% Cu was tested to determine the leachability of Cu and Co using sulphuric acid and hydrogen peroxide mixtures at different conditions. Without hydrogen peroxide, the maximum extraction of copper and cobalt were found to be ~80% and ~15%, respectively when the acid concentration was varied between 0.36 - 1.1M. When hydrogen peroxide was added (0.008-0.042M, Cu recovery was enhanced to ~90%. Recoveries of ~90% of Co could be achieved at 20ºC, using leachants consisting of 0.36M sulphuric acid and 0.025M hydrogen peroxide after 3 hours. The reaction time to reach 90% Co extraction was reduced to less than 2 hours at 30ºC. Stabcal modelling of the Eh-pH diagrams shows the importance of hydrogen peroxide as a reductant. The decrease of solution potential (300-350 mV by adding hydrogen peroxide was confirmed by Eh measurements during the tests. The leaching follows the shrinking core model kinetics, where the rate constant is linearly dependent on hydrogen peroxide concentration in the range 0-0.025M and proportional to (1/r2 where r is the average radius of the mineral particles. The activation energy for the leaching process is 72.3 kJ/mol.

Reinforced sulphur concrete

NARCIS (Netherlands)

2014-01-01

Reinforced sulphur concrete wherein one or more metal reinforcing members are in contact with sulphur concrete is disclosed. The reinforced sulphur concrete comprises an adhesion promoter that enhances the interaction between the sulphur and the one or more metal reinforcing members.

On the effects of organic matter and sulphur-containing compounds on the CCN activation of combustion particles

Directory of Open Access Journals (Sweden)

A. Petzold

2005-01-01

Full Text Available The European PartEmis project (Measurement and prediction of emissions of aerosols and gaseous precursors from gas turbine engines was focussed on the characterisation and quantification of exhaust emissions from a gas turbine engine. The combustion aerosol characterisation included on-line measurements of mass and number concentration, size distribution, mixing state, thermal stability of internally mixed particles, hygroscopicity, cloud condensation nuclei (CCN activation potential, and off-line analysis of chemical composition. Based on this extensive data set, the role of sulphuric acid coating and of the organic fraction of the combustion particles for the CCN activation was investigated. Modelling of CCN activation was conducted using microphysical and chemical properties obtained from the measurements as input data. Coating the combustion particles with water-soluble sulphuric acid, increases the potential CCN activation, or lowers the activation diameter, respectively. The adaptation of a Köhler model to the experimental data yielded coatings from 0.1 to 3 vol-% of water-soluble matter, which corresponds to an increase in the fraction of CCN-activated combustion particles from ≤10−4 to ≌10−2 at a water vapour saturation ratio Sw=1.006. Additional particle coating by coagulation of combustion particles and aqueous sulphuric acid particles formed by nucleation further reduces the CCN activation diameter. In contrast, particles containing a large fraction of non-volatile organic compounds grow significantly less at high relative humidity than particles with a lower content of non-volatile OC. The resulting reduction in the potential CCN activation with an increasing fraction of non-volatile OC becomes visible as a trend in the experimental data. While a coating of water-soluble sulphuric acid increases the potential CCN activation, or lowers the activation diameter, respectively, the non-volatile organic compounds, mainly found at

Vapor mercury uptake with sulphur impregnated active carbons derived using sulphur dioxide

International Nuclear Information System (INIS)

Tong, S.; Methta, H.; Ahmed, I.; Morris, E.; Fuentes de Maria, L.; Jia, C.Q.

2008-01-01

Active carbon adsorption is the primary technology used for removal of vapour mercury from flue gases in coal-fired power plants, municipal solid waste combustors, and other sources. It can be carried out using two different processes, notably injection of powder active carbon into flue gas streams upstream of the particulate collection devices, and filtration with a granular active carbon fixed bed downstream of the flue gas desulphurization units and/or particulate collectors. This paper presented an investigation of vapour mercury uptake performance of laboratory-made sulphur impregnated active carbons (SIACs) using a fixed bed reactor in a temperature range of 25 to 200 degrees Celsius. The materials and methods as well as the properties of activated carbons studied were presented. The experimental set-up was also described. The paper discussed the effects of initial concentration, the flow rate, the loading amount of SIACs, temperature, and the sulphur impregnation on the mercury uptake performance. The study showed that SIACs produced with sulphur dioxide exhibited a more complicated behaviour when temperature was varied, implying a mixed adsorption mechanism. 10 refs., 3 tabs., 8 figs

Sulphur output from oil sands : dramatically changing Alberta's sulphur balance

Energy Technology Data Exchange (ETDEWEB)

D' Aquin, G. [Con-Sul Inc., Bigfork, MT (United States)

2008-07-01

This paper discussed sulphur production from Alberta's gas and oil sands industries. While sulfur derived from natural gas production in the province is expected to decline as natural gas reserves diminish, Alberta's oil sands contain high amounts of sulphur. It is not yet known how much sulphur will be produced from the province's oil sands facilities. Alberta had considerable stockpiles of sulphur in the 1970s. By 1980, inventories began to decline. By 1996, output had increased to 7.1 million tonnes. Alberta's sulphur inventory reached 9.7 million tonnes following the collapse of the Soviet Union's government mandated fertilizer industry. In 2006, sulphur supplies in Alberta reached 12 million tonnes. Reduced global output has now lowered sulphur stockpiles. Increases in sulphur prices tend to reduce market demand, and lower prices will not typically change the volume of sulphur produced as a byproduct of oil and gas operations. Bitumen-derived sulphur output is expected to exceed gas-derived sulphur output in the near future. Sulphur from oil sands processing is expected to increase by 5 million tonnes by 2017. Increased sulphur production levels in Alberta will present a significant challenge for all sectors of the hydrocarbon industry. It was concluded that developing a plan for storing, selling or disposing of the sulphur will help to ensure the profitability of oil sands operations.

The recovery of uranium, gold and sulphur from residues from South African mines

International Nuclear Information System (INIS)

Toens, P.D.

1978-10-01

The slimes dams resulting from the operations of gold and gold/uranium mines situated within the Witwatersrand Basin contain low concentrations of gold, uranium and pyrite. As a result of a marked increase in the prices of both gold and uranium in recent years, two schemes involving the recovery of these minerals also the manufacture of sulphuric acid as a by-product are operating profitably. Further schemes are under investigation [af

Gas chromatography and silver-ion high-performance liquid chromatography analysis of conjugated linoleic acid isomers in free fatty acid form using sulphuric acid in methanol as catalyst.

Science.gov (United States)

Luna, Pilar; Juárez, Manuela; de la Fuente, Miguel Angel

2008-09-12

This study used GC and silver-ion HPLC to examine the effects of temperature and time on methylation of individual and mixtures of conjugated linoleic acid (CLA) isomers in free fatty acid form using sulphuric acid as catalyst. In the conditions tested (temperatures between 20 and 50 degrees C and times between 10 and 60 min) methylation was complete while avoiding isomerization of conjugated dienes and the formation of artefacts that could interfere with chromatographic determinations. An analytical method using solvent extraction of the lipids followed by selective elution of the free fatty acids from aminopropyl bonded phase columns and methylation with H(2)SO(4) in mild conditions was then applied to determine the CLA isomers in free fatty acid form in rumen fluid, and the results were evaluated.

Morphology and evolution of sulphuric acid caves in South Italy

Science.gov (United States)

D'Angeli, Ilenia M.; De Waele, Jo; Galdenzi, Sandro; Madonia, Giuliana; Parise, Mario; Vattano, Marco

2016-04-01

Sulphuric acid speleogenesis (SAS) related to the upwelling of acid water enriched in H2S and CO2 represents an unusual way of cave development. Since meteoric infiltration waters are not necessarily involved in speleogenesis, caves can form without the typical associated karst expressions (i.e. dolines) at the surface. The main mechanism of sulphuric acid dissolution is the oxidation of H2S (Jones et al., 2015) which can be amplified by bacterial mediation (Engel et al., 2004). In these conditions, carbonate dissolution associated with gypsum replacement, is generally believed to be faster than the normal epigenic one (De Waele et al., 2016). In Italy several SAS caves have been identified, but only few systems have been studied in detail: Frasassi and Acquasanta Terme (Marche)(Galdenzi et al., 2010), Monte Cucco (Umbria) (Galdenzi & Menichetti, 1995), and Montecchio (Tuscany) (Piccini et al., 2015). Other preliminary studies have been carried out in Calabria (Galdenzi, 2007) and Sicily (De Waele et al., 2016). Several less studied SAS cave systems located in South Italy, and in particular in Apulia (Santa Cesarea Terme), Sicily (Acqua Fitusa, Acqua Mintina) and Calabria (Mt. Sellaro and Cassano allo Ionio) have been selected in the framework of a PhD thesis on SAS caves and their speleogenesis. Using both limestone tablet weight loss (Galdenzi et al., 2012) and micro erosion meter (MEM) (Furlani et al., 2010) methods the dissolution rate above and under water in the caves will be quantified. Geomorphological observations, landscape analysis using GIS tools, and the analysis of gypsum and other secondary minerals (alunite and jarosite) (stable isotopes and dating) will help to reconstruct the speleogenetic stages of cave formation. Preliminary microbiological analysis will determine the microbial diversity and ecology in the biofilms. References Engel S.A., Stern L.A., Bennett P.C., 2004 - Microbial contributions to cave formation: New insight into sulfuric acid

Sulphur uptake and yield of soybean as influenced by sulphur fertilization

International Nuclear Information System (INIS)

Shamima, N.; Farid, A. T. M.

2005-01-01

Effect of sulphur fertilization (0, 20, 40, 60 and 80 kg/ha) on sulphur uptake and seed yield was studied in sohag and Bangladesh soybean-4 varieties in the field of Bangladesh Agricultural Research Institute, Gazipur during the winter (rabi) seasons of 2000-2001 and 2001-2002 in grey Terrace soil (Albaquept). Addition of slphur fertilizer exerted significant influence on the yield attributes of soybean varieties. Sulphur uptake also significantly responded to the application of sulphur fertilizer. Variety Bangladesh soybean-4 was found superior to sohag in respect of sulphur uptake and yield. Greater sulphur utilization was observed at lower levels of fertilizer application. Seed yield and sulphur uptake were increased with the application of 40 kg/ ha for sohag and 60 kg/ha for Bangladesh soybean-4. Response of seed yield to added sulphur was quadratic. The economic optimum doses were found to be 49 kg s/ha for sohag and 52 kg s/ha for Bangladesh soybean-4, yielding 2060 and 2354 kg/ha, respectively. (author)

Uranium adsorption from the sulphuric acid leach liquor containing more chlorides with cation-exchange resin SL-406

International Nuclear Information System (INIS)

Hu Jun; Wang Zhaoguo; Chi Renqing; Niu Xuejun

1994-01-01

The feasibility of uranium adsorption was studied from the sulphuric acid leach liquor of a uranium ore containing more chlorides with cation-exchange resin SL-406. The influence of some factors on uranium adsorption was investigated. It was shown that the resin possesses better selectivity, stability and higher capacity. It can be effectively used to recovery uranium from leach liquors of uranium ores containing more chlorides

Radioisotopic determination methods of sulphur dispersion and sulphur blooming in rubber compounds

International Nuclear Information System (INIS)

Goraczka, W.; Koczorowska, E.

1997-01-01

It is well known that the concentration of sulphur in rubber compounds essentially effects the structure of the vulkanizate network. But there are no efficient and accurate methods to estimate the dispersion and migration (blooming) of curatives in raw rubber. In the work radioisotope methods have been analyzed to study the dispersion of curatives, physical and chemical processes in rubber and to optimize technical conditions of tire production. The radioactivity of the 35 S isotope introduced into rubber compounds has been measured by volumetric and surface methods. It was proved that the radioisotopic methods can be used in the studies. Experimental data of the effect of selected technological factors on these processes are presented. Rubber compounds containing soluble sulphur were made for such investigations. These methods permit detection of concentrations 10 -6 g of the radioactive isotope per 0.1 g of rubber compound. The sensitivity of these methods enables the investigation of radioisotope behaviour in rubber compounds during processing on an industrial scale without any hazards for workers

The use of ion-selective membranes for the recovery of sulphuric acid out of contaminated solutions. Comparing electrodialysis, electro electrodialysis and diffusion dialysis

International Nuclear Information System (INIS)

Cattoir, S.

1998-02-01

The amount of waste arising from dismantled reactors is minimized by decontamination processes. These processes result in contaminated effluents, containing acid and metal salts. The quantity of final waste can be substantially reduced when the acid is extracted out of the decontamination effluents prior to neutralisation. This report discusses three membrane techniques for the displacement of acids out of mixed acid/salt solutions: electrodialysis (ED), electro electrodialysis (EED) and diffusion dialysis (DD). EED uses an electrical potential difference across an anion-selective membrane; DD uses a concentration difference across an anion-selective membrane; ED uses an electrical potential difference, across an anion- and a cation-selective membrane. EED can displace up to 90% of the sulphuric acid, the amount of metal ions in the displaced-acid solution is less than 1% of the ions in the original contaminated solution. Treatment costs are estimated to about 18 Belgian Francs per litre. In DD the purity of the displaced acid is comparable to EED. Treatment costs are about 21 Belgian Francs per litre. In ED 90% acid-displacement is easily reached, but 5% metal ions are also displaced. Treatment costs are about 6 Belgian Francs per litre. Therefore, in spite of the lower purity of the resulting acid, ED is economically speaking the best choice

Effect of sulphuric acid concentration on electroosmotic flow through polymer electrolyte membranes in PEM fuel cells. Paper no. IGEC-1-061

International Nuclear Information System (INIS)

Karimi, G.; Li, X.

2005-01-01

Polymer electrolyte membrane (PEM) fuel cells are highly efficient and environmentally clean, and hence one of the most promising power sources for both stationary and mobile applications. The operations of PEM fuel cells are complicated by the electroosmotic flow of water from anode to cathode through the polymer electrolyte membrane leading to the membrane dehydration and fuel cell performance degradations. In this study, electro osmotic flow in polymer electrolyte membranes is modeled by incorporating the electro kinetic effects in the presence of euphoric acid. The governing Poisson-Boatman and the Nervier-Stokes equations were solved numerically for a single membrane pore to determine the electro osmotic flow distributions through the membrane over a wide range of acid concentrations. The presence of euphoric acid modifies the protons distribution in the membrane and hence alters the driving force for electroosmotic drag. Numerical results indicate that the electro osmotic flow increases steadily with acid concentration. The water transport due to electro osmosis is almost doubled at 2 M acid concentration compared with that of non-doped membrane. The value of electroosmotic drag coefficient however falls steadily with acid concentration due to the presence of a larger number of protons in the electrolyte. (author)

Nitrogen and Sulphur Relations in Effecting Yield and Quality of Cereals and Oilseed Crops

Directory of Open Access Journals (Sweden)

B.K. Nad

2001-01-01

Full Text Available Nitrogen and sulphur, both vital structural elements, are especially needed for the synthesis of proteins and oils. Investigations revealed the required application of sulphur is one half to one third the amount of nitrogen, and the ratio becomes narrower in mustard (Brassica juncea L., followed by wheat and rice. The efficiency of an increased level of nitrogen required a proportionately higher amount of sulphur. A critical investigation on the effective utilization of applied vis-à-vis absorbed nitrogen in wheat and mustard envisaged accumulation of NO3-N in vegetative parts when sulphur remained proportionately low. Application of sulphur hastened the chemical reduction of absorbed NO3– for its effective utilization. The effect was more pronounced in mustard than in wheat. Easily available forms of sulphur, like ammonium sulphate and gypsum, as compared to pyrite or elemental sulphur, maintained adequate N to S ratio in rice, resulting in a reduction in the percent of unfilled grain, a major consideration in rice yield. A narrow N to S ratio, with both at higher levels, increased the oil content but raised the saponification value of the oil, a measure of free fatty acids. Whereas, a proportionately narrow N to S ratio at moderate dose resulted in adequately higher seed and oil yield with relatively low saponification value, associated with increased iodine value of the oil, indicating respectively low free fatty acids and higher proportion of unsaturated fatty acids, an index for better quality of the oil.

Sulphur highways : value-added solutions to create sulphur demand

Energy Technology Data Exchange (ETDEWEB)

Macedo, R.

2010-09-15

Producers generally view sulphur as a nuisance with essentially no benefit. In Alberta, a greater portion of sulphur production will shift from natural gas to the oilsands producing areas where there is limited infrastructure to move it out. Increased amounts of sour oil and gas production together with greater fuel desulphurization have also led to more sulphur being produced. In order to address the inevitable storage issue, Shell is considering value-added uses for the product, such as sulphur asphalt. The company developed Thiopave, a sulphur-based product for use in asphalt paving mixtures that can improve the mechanical performance of asphalt. The sulphur can be added to the asphalt mix as a solid pellet, which helps reduce the emission of sulphur vapour, odour and eye irritation. Twenty Thiopave projects are planned for the 2010 paving season in 9 U.S. states and 2 Canadian provinces. Sulphur Enhanced Asphalt Modifier (SEAM) was the first generation of Thiopave developed in 2003. SEAM replaces 20 to 25 percent by volume of the bitumen in asphalt mix. The properties allow Thiopave-enhanced roads to perform better than conventional roads in both consistently high temperature regions and climates with wide temperature variations. In 2007, an asphalt mix containing 40 percent by mass of Thiopave was used in a trial in Qatar. The Thiopave asphalt mix was compared with a conventional mix at temperatures ranging from 10 to 40 degrees C to determine the stiffness ratio. It was determined that Thiopave mixes containing high-penetration bitumen can be used to build temperature resistant roads that are stiffer in hot summer temperatures while improving the pavement's cold weather cracking performance. 1 ref., 4 figs.

Effects of sulphuric acid pollution on the biology of streams in the Transvaal, South Africa

Energy Technology Data Exchange (ETDEWEB)

Harrison, A D

1958-01-01

Strongly acid effluents or drainage waters are produced during gold and coal mining activities in the Transvaal. Sulphuric acid is produced during oxidation of pyrites exposed by mining operations and much of it finds its way into streams and creates serious pollution problems. The object of this paper is to give a short account of the effects of this acid pollution on the biology of these streams. The first streams considered are the Klip and Klipspruit near their confluence at Olifantsvlei, near Johannesburg. These were studied during a two-year investigation of the area. Both receive acid pollution from gold mine dumps and slimes dams, the seepages from which have pH values as low as 2.3. Both streams run over dolomite formations so the acid is gradually neutralised but highly mineralised, permanently hard water results. The Klip and the Klipspruit join in the middle of a y-shaped, swampy area, each stream coming down one of the upper arms of the y. A sampling station was set up on each where it runs slowly through the swamp just before confluence.

European transboundary acidifying air pollution. Ten years calculated fields and budgets to the end of the first Sulphur Protocol

Energy Technology Data Exchange (ETDEWEB)

Barrett, K.; Seland, Oe.; Foss, A.; Mylona, S.; Sandnes, H.; Styve, H.; Tarrason, L.

1995-07-01

The Cooperative Programme for the Monitoring and Evaluation of the Long Range Transmission and Air Pollutants in Europe, EMEP, plays an integral part in data collection and scientific cooperation for implementation of the 1979 Geneva Convention on Long Range Transboundary Air Pollution. Within EMEP, the Meteorological Synthesizing Centre - West (MSC-W) is an international technical centre. The purpose of the MSC-W, focusing in part on acidifying substances, is to estimate the concentrations of relevant sulphur and nitrogen pollutants across Europe on the basis of emission information and meteorological data, and to estimate the transboundary fluxes of these substances. Responding to these specific obligations, the report presents calculations of sulphur and nitrogen concentrations and depositions and of their transboundary fluxes. The calculations are performed by the receptor oriented one layer trajectory (Lagrangian) acid deposition model, which during 1995 has been used to estimate acidifying pollutant fluxes for the ten year period 1985-1994. This corresponds to the period between initial signing and conclusion of the first Sulphur Protocol, signed in Helsinki in 1985. 90 refs., 42 figs., 43 tabs.

Hydrofluoric–nitric–sulphuric-acid surface treatment of tungsten for carbon fibre-reinforced composite hybrids in space applications

Energy Technology Data Exchange (ETDEWEB)

Kanerva, M., E-mail: Mikko.Kanerva@aalto.fi [Aalto University, School of Engineering, Department of Applied Mechanics, P.O.B. 14300, FI-00076 Aalto (Finland); Johansson, L.-S.; Campbell, J.M. [Aalto University, School of Chemical Technology, Department of Forest Products Technology, P.O.B. 16300, FI-00076 Aalto (Finland); Revitzer, H. [Aalto University, School of Chemical Technology, Department of Chemistry, P.O.B. 16300, FI-00076 Aalto (Finland); Sarlin, E. [Tampere University of Technology, Department of Materials Science, P.O.B. 589, FI-33101 Tampere (Finland); Brander, T.; Saarela, O. [Aalto University, School of Engineering, Department of Applied Mechanics, P.O.B. 14300, FI-00076 Aalto (Finland)

2015-02-15

Highlights: • XPS and AFM analysis of the effect of hydrofluoric–nitric–sulphuric-acid on tungsten. • Dreiling's model established 54.4% thinning of WO{sub 3} due to 67 s treatment. • Strain energy release rate increased ≈8.4 J/m{sup 2} at the interface. • Failure loci analysis expressed the oxide and carbon fibre surfaces as weak points. - Abstract: Hybrid material systems, such as combinations of tungsten foils and carbon fibre-reinforced plastic (CFRP), are replacing metal alloy concepts in spacecraft enclosures. However, a good adhesion between the tungsten oxide scale and the epoxy resin used is required. Here, the effects of a hydrofluoric–nitric–sulphuric-acid (HFNS) treatment on tungsten oxides and subsequent adhesion to CFRP are analysed using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and fracture testing. The work shows that HFNS treatment results in decreased oxygen content, over 50% thinner tungsten trioxide (WO{sub 3}) layer and increased nano-roughness on thin tungsten foils. Fracture testing established a 39% increase in the average critical strain for tungsten–CFRP specimens after HFNS treatment was carried out on tungsten. The effect of the oxide scale modification regarding the critical strain energy release rate was ΔG{sub c}≈ 8.4 J/m{sup 2}.

Sulphur cement pre-composition and process for preparing such sulphur cement pre-composition

NARCIS (Netherlands)

2013-01-01

The invention provides a process for the preparation of a sulphur cement pre-composition comprising reacting sulphur modifier with polysulphide-containing organosilane to obtain in the presence of sulphur the sulphur cement pre-composition, wherein the organosilane has the general molecular formula:

Polioencephalomalacia in ruminants caused by excessive amount of sulphur - a review

Directory of Open Access Journals (Sweden)

Lutnicki Krzysztof

2014-06-01

Full Text Available Polioencephalomalacia as a result of sulphur excess is a growing problem in cattle and sheep, mainly in young, growing animals. It is common in different regions of the world. The disease develops favoured by certain conditions such as sustained provision of feed and water with high sulphur content, use of dietary supplements containing sulphur, and a habitat with high hydrogen sulphide concentration. Pathogenesis of the disease is complex, but very important are oxidative-antioxidative imbalance, dysfunction of vessels, and secondary cerebral cortex ischaemia as a result of direct and/or indirect action of sulphur metabolites, namely hydrogen sulphide, sulphides, and sulphites. Clinical signs and changes in the cerebral cortex in the form of degenerative necrotic lesions are similar to those observed in polioencephalomalacia caused by vitamin B1 deficiency, and lead and salt intoxication. Highly increased sulphur content (more than 0.3-0.4 of dry matter in the diet is the basis for differential diagnosis, as well the high concentration of hydrogen sulphide in gas and sulphides in rumen fluid. In prophylaxis and treatment the most important measure is to limit sulphur intake and in acute cases to neutralise low pH in rumen and administer vitamin B1 injections.

Concentration and transport of nitrate by the mat-forming sulphur bacterium Thioploca

Science.gov (United States)

Fossing, H.; Gallardo, V. A.; Jørgensen, B. B.; Hüttel, M.; Nielsen, L. P.; Schulz, H.; Canfield, D. E.; Forster, S.; Glud, R. N.; Gundersen, J. K.; Küver, J.; Ramsing, N. B.; Teske, A.; Thamdrup, B.; Ulloa, O.

1995-04-01

MARINE species of Thioploca occur over 3,000 km along the continental shelf off Southern Peru and North and Central Chile1-4. These filamentous bacteria live in bundles surrounded by a common sheath and form thick mats on the sea floor under the oxygen-minimum zone in the upwelling region, at between 40 and 280 m water depth. The metabolism of this marine bacterium5,6 remained a mystery until long after its discovery1,7. We report here that Thioploca cells are able to concentrate nitrate to up to 500 mM in a liquid vacuole that occupies >80% of the cell volume. Gliding filaments transport this nitrate 5-10 cm down into the sediment and reduce it, with concomitant oxidation of hydrogen sulphide, thereby coupling the nitrogen and sulphur cycles in the sediment.

Enhanced corrosion resistance of stainless steel type 316 in sulphuric acid solution using eco-friendly waste product

Science.gov (United States)

Sanni, O.; Popoola, A. P. I.; Fayomi, O. S. I.

2018-06-01

Literature has shown that different organic compounds are effective corrosion inhibitors for metal in acidic environments. Such compounds usually contain oxygen, nitrogen or sulphur and function through adsorption on the metal surface, thereby creating a barrier for corrosion attack. Unfortunately, these organic compounds are toxic, scarce and expensive. Therefore, plants, natural product and natural oils have been posed as cheap, environmentally acceptable, abundant, readily available and effective molecules having low environmental impact. The corrosion resistance of austenitic stainless steel Type 316 in the presence of eco-friendly waste product was studied using weight loss and potentiodynamic polarization techniques in 0.5 M H2SO4. The corrosion rate and corrosion potential of the steel was significantly altered by the studied inhibitor. Results show that increase in concentration of the inhibitor hinders the formation of the passive film. Experimental observation shows that its pitting potential depends on the concentration of the inhibitor in the acid solution due to adsorption of anions at the metal film interface. The presence of egg shell powder had a strong influence on the corrosion resistance of stainless steel Type 316 with highest inhibition efficiency of 94.74% from weight loss analysis, this is as a result of electrochemical action and inhibition of the steel by the ionized molecules of the inhibiting compound which influenced the mechanism of the redox reactions responsible for corrosion and surface deterioration. Inhibitor adsorption fits the Langmuir isotherm model. The two methods employed for the corrosion assessment were in good agreement.

Contribution to the study of the electrochemical behaviour of titanium and of its industrial shores in sulphuric environment. Characteristics of their resistance to pitting corrosion in neutral and acid halogenous environment

International Nuclear Information System (INIS)

Petit, Jacques-Alain

1975-01-01

After a presentation of the general metallurgical, physical, and corrosion resistance characteristics of titanium and of its alloys, this research thesis presents the experimental means, discusses the influence of experimental conditions on the assessment of the electrochemical behaviour of titanium and of its alloys. It reports an investigation of the cathodic behaviour of non-alloyed titanium and notably the hydrogen release kinetics in a concentrated acid environment. It discusses the influence of alloy composition on their cathodic behaviour, addresses the anodic behaviour of titanium and of its alloys in sulphuric environment, and the pitting corrosion of titanium and of its alloys in an acid and neutral halogenous environment [fr

Design and modeling of an advanced marine machinery system including waste heat recovery and removal of sulphur oxides

DEFF Research Database (Denmark)

Frimann Nielsen, Rasmus; Haglind, Fredrik; Larsen, Ulrik

2014-01-01

the efficiency of machinery systems. The wet sulphuric acid process is an effective way of removing flue gas sulphur oxides from land-based coal-fired power plants. Moreover, organic Rankine cycles (ORC) are suitable for heat to power conversion for low temperature heat sources. This paper describes the design...... that an ORC placed after the conventional waste heat recovery system is able to extract the sulphuric acid from the exhaust gas, while at the same time increase the combined cycle thermal efficiency by 2.6%. The findings indicate that the technology has potential in marine applications regarding both energy...... and modeling of a highly efficient machinery system which includes the removal of exhaust gas sulphur oxides. The system consists of a two-stroke diesel engine, the wet sulphuric process for sulphur removal, a conventional steam Rankine cycle and an ORC. Results of numerical modeling efforts suggest...

Separation of thorium (IV) from lanthanide concentrate (LC) and water leach purification (WLP) residue

International Nuclear Information System (INIS)

AL-Areqi, Wadeeah M.; Majid, Amran Ab.; Sarmani, Sukiman

2014-01-01

Thorium (IV) content in industrial residue produced from rare earth elements production industry is one of the challenges to Malaysian environment. Separation of thorium from the lanthanide concentrate (LC) and Water Leach Purification (WLP) residue from rare earth elements production plant is described. Both materials have been tested by sulphuric acid and alkaline digestions. Th concentrations in LC and WLP were determined to be 1289.7 ± 129 and 1952.9±17.6 ppm respectively. The results of separation show that the recovery of Th separation from rare earth in LC after concentrated sulphuric acid dissolution and reduction of acidity to precipitate Th was found 1.76-1.20% whereas Th recovery from WLP was less than 4% after concentrated acids and alkali digestion processes. Inductively Coupled Plasma-Mass Spectroscopy (ICP-MS) was used to determine Th concentrations in aqueous phase during separation stages. This study indicated that thorium maybe exists in refractory and insoluble form which is difficult to separate by these processes and stays in WLP residue as naturally occurring radioactive material (NORM)

Leaching of vanadium from sulphuric acid manufacture spent catalysts

Directory of Open Access Journals (Sweden)

García, Diego Juan

2001-02-01

Full Text Available Recovery of vanadium contained in spent catalysts from the manufacture of sulphuric acid has been studied in this work, resulting in an industrial multistage process for the treatment of them avoiding direct deposition or dumping. Characterization of supplied spent catalysts samples, confirmed vanadium levels showed in the literature. The study of variables influencing leaching process: type of leaching agent, leaching agent concentration, S/L ratio, stirring speed and temperature, allows to fix the most advantageous conditions using industrial application criterion and verifying that the process is difusión controlled. The work is completed by developing an industrial leaching cycle simulation with the aim of reproducing real performance of spent catalyst, proposing operating conditions, and verifying the non-toxic character of the final residue obtained.

En el presente trabajo se ha estudiado la recuperación del vanadio contenido en los catalizadores agotados procedentes de la fabricación del ácido sulfúrico, planteando un proceso industrial multietapa para el tratamiento de estos residuos, evitando su deposición o vertido directos. La caracterización de las muestras de catalizadores agotados disponibles confirmó los valores encontrados en la bibliografía. Se estudiaron las variables que influyen en el proceso de lixiviación (tipo de agente de lixiviación y concentración del mismo, relación S/L, velocidad de agitación y temperatura definiendo las condiciones más adecuadas desde el punto de vista industrial y verificando que el proceso está controlado por mecanismos difusionales. El trabajo se completa con la simulación de un ciclo industrial de lavado del catalizador y la verificación de la nula toxicidad de los lixiviados obtenidos por degradación del residuo final. 24 Aplicación de la resistencia de ruido al estudio de pinturas ricas en zinc Noise resistance applied to the study of zinc rich paints

Temperature Effects on Stainless Steel 316L Corrosion in the Environment of Sulphuric Acid (H2SO4)

Science.gov (United States)

Ayu Arwati, I. G.; Herianto Majlan, Edy; Daud, Wan Ramli Wan; Shyuan, Loh Kee; Arifin, Khuzaimah Binti; Husaini, Teuku; Alfa, Sagir; Ashidiq, Fakhruddien

2018-03-01

In its application, metal is always in contact with its environment whether air, vapor, water, and other chemicals. During contact, chemical interactions emerge between metals and their respective environments such that the metal surface corrodes. This study aims to determine the corrosion rate of 316L stainless steel sulphuric acid environment (H2SO4) with weight loss and electrochemical methods. The corrosion rate (CR) is value of 316L stainless steel by weight loss method with sulfuric acid (H2SO4) with concentration of 0.5 M. The result obtained in conjunction with the increase of temperature the rate of erosion obtained appears to be larger, with a consecutive 3 hour the temperature of 50°C is 0.27 mg/cm2h, temperature 70°C 0.38 mg/cm2h, and temperature 90 °C 0.52 mg/cm2h. With the electrochemical method, the current value increases by using a C350 potentiostal tool. The higher the current, the longer the time the corrosion rate increases, where the current is at 90 °C with a 10-minute treatment time of 0.0014736 A. The 316L stainless steel in surface metal morphology is shown by using a Scanning Electron Microscope (SEM).

Acid-catalysed xylose dehydration into furfural in the presence of kraft lignin.

Science.gov (United States)

Lamminpää, Kaisa; Ahola, Juha; Tanskanen, Juha

2015-02-01

In this study, the effects of kraft lignin (Indulin AT) on acid-catalysed xylose dehydration into furfural were studied in formic and sulphuric acids. The study was done using D-optimal design. Three variables in both acids were included in the design: time (20-80 min), temperature (160-180°C) and initial lignin concentration (0-20 g/l). The dependent variables were xylose conversion, furfural yield, furfural selectivity and pH change. The results showed that the xylose conversion and furfural yield decreased in sulphuric acid, while in formic acid the changes were minor. Additionally, it was showed that lignin has an acid-neutralising capacity, and the added lignin increased the pH of reactant solutions in both acids. The pH rise was considerably lower in formic acid than in sulphuric acid. However, the higher pH did not explain all the changes in conversion and yield, and thus lignin evidently inhibits the formation of furfural. Copyright © 2014 Elsevier Ltd. All rights reserved.

Measurements for the determination of acid dew point and SO[sub 3] concentration in the flue gas of utility boilers

Energy Technology Data Exchange (ETDEWEB)

Derichs, W.; Menden, W.; Ebel, P.K. (RWE Energie AG, Bergheim (Germany))

1991-10-01

Until now, the well-known measuring systems for determining acid dewpoint have been applied primarily to flue gases from oil-fired combustion. Using an acid dewpoint measuring system which has now been available on the market for some time, it is possible to measure the acid dewpoint reliably and continuously in flue gas from coal-fired combustion, with low SO[sub 3] concentrations. This measuring system has also been used for flue gas from which the dust and sulphur have been removed as well as for untreated flue gas of conventional combustion systems with gas, oil, hard coal and brown coal firing and also in fluidized bed combustion systems. 6 refs., 11 figs., 2 tabs.

Molecular understanding of sulphuric acid-amine particle nucleation in the atmosphere

CERN Document Server

Almeida, João; Kürten, Andreas; Ortega, Ismael K; Kupiainen-Määttä, Oona; Praplan, Arnaud P; Adamov, Alexey; Amorim, Antonio; Bianchi, Federico; Breitenlechner, Martin; David, André; Dommen, Josef; Donahue, Neil M; Downard, Andrew; Dunne, Eimear; Duplissy, Jonathan; Ehrhart, Sebastian; Flagan, Richard C; Franchin, Alessandro; Guida, Roberto; Hakala, Jani; Hansel, Armin; Heinritzi, Martin; Henschel, Henning; Jokinen, Tuija; Junninen, Heikki; Kajos, Maija; Kangasluoma, Juha; Keskinen, Helmi; Kupc, Agnieszka; Kurtén, Theo; Kvashin, Alexander N; Laaksonen, Ari; Lehtipalo, Katrianne; Leiminger, Markus; Leppä, Johannes; Loukonen, Ville; Makhmutov, Vladimir; Mathot, Serge; McGrath, Matthew J; Nieminen, Tuomo; Olenius, Tinja; Onnela, Antti; Petäjä, Tuukka; Riccobono, Francesco; Riipinen, Ilona; Rissanen, Matti; Rondo, Linda; Ruuskanen, Taina; Santos, Filipe D; Sarnela, Nina; Schallhart, Simon; Schnitzhofer, Ralf; Seinfeld, John H; Simon, Mario; Sipilä, Mikko; Stozhkov, Yuri; Stratmann, Frank; Tomé, Antonio; Tröstl, Jasmin; Tsagkogeorgas, Georgios; Vaattovaara, Petri; Viisanen, Yrjo; Virtanen, Annele; Vrtala, Aron; Wagner, Paul E; Weingartner, Ernest; Wex, Heike; Williamson, Christina; Wimmer, Daniela; Ye, Penglin; Yli-Juuti, Taina; Carslaw, Kenneth S; Kulmala, Markku; Curtius, Joachim; Baltensperger, Urs; Vehkamaki, Hanna; Kirkby, Jasper

2013-01-01

Nucleation of aerosol particles from trace atmospheric vapours is thought to provide up to half of global cloud condensation nuclei. Aerosols can cause a net cooling of climate by scattering sunlight and by leading to smaller but more numerous cloud droplets, which makes clouds brighter and extends their lifetimes. Atmospheric aerosols derived from human activities are thought to have compensated for a large fraction of the warming caused by greenhouse gases. However, despite its importance for climate, atmospheric nucleation is poorly understood. Recently, it has been shown that sulphuric acid and ammonia cannot explain particle formation rates observed in the lower atmosphere. It is thought that amines may enhance nucleation, but until now there has been no direct evidence for amine ternary nucleation under atmospheric conditions. Here we use the CLOUD (Cosmics Leaving OUtdoor Droplets) chamber at CERN and find that dimethylamine above three parts per trillion by volume can enhance particle formation rates ...

Characterization of acid tar waste from benzol purification | Danha ...

African Journals Online (AJOL)

The use of concentrated sulphuric acid to purify benzene, toluene and xylene produces acidic waste known as acid tar. The characterization of the acid tar to determine the composition and physical properties to device a way to use the waste was done. There were three acid tars two from benzene (B acid tar), toluene and ...

Study of oxidation-reduction reactions of plutonium and neptunium in sulphuric-phosphoric acid media

International Nuclear Information System (INIS)

Moiseev, I.V.; Kuperman, A.Ya.; Borodina, N.N.; Galkina, V.N.; Vinokurov, V.A.

1976-01-01

Potentiostatic, coulometric, potentiometric, and amperometric methods have been used for determining the rate constants of disproportionation (ksub(d)) of plutonium(5) and neptunium (5) and normal real redox potentials (Esub(0)sup(p)) of the following ion pairs in sulphur-phosphoric-acid media: PuOsub(2)sup(2)sup(+) (PuO 2 + , Pu 4+ /Pu 3+ , NpO 2 2+ /NpO 2 + , NpO 2 2+ /Np 4+ , NpO 2 + /Np 4+ , and Fe 3+ /Fe 2+ . The regularities have been shown of changing ksub(d) and Esub(o)sup(p) as a function of H 2 SO 4 and H 3 PO 4 concentration. It has been established that for plutonium and neptunium a linear correlation is observed between lg ksub(d) and Esub(o)sup(p) of the ion pairs NpO 2 2+ /NpO 2 + , NpO 2 2 /Np 4+ , NpO 2 + /Np 4+ and PuO 2 2+ /PuO 2 + in a wide range of their values. The correlation coefficient is close to unity in all cases (no less than 0.96). The results of investigations have made it possible to recommend optimum compositions of background electrolytes for performing continuous amperostatic coulometric titration of Pusup((6)) and Npsup((6)) up to four valent state by electrogenerated ions of iron (2)

Distribution of sulphur and trace elements in peat. [Literature survey with some additional sulphur analyses

Energy Technology Data Exchange (ETDEWEB)

Huttunen, S; Karhu, M

1981-01-01

A survey on the literature and contemporary research was made on peat sulphur and trace element studies. Marked variance between different peatlands and peat types has been noted. The available information is still inadequate for generalizations or statistical analysis mainly due to methodological variations and temporal and spatial variations in results. At the moment, the criteria applied in peatland inventories and evaluations are inadequate with respect to peat quality determinations. To some extent the quality of fuel peat should be determined in a mire inventory prior to peatland utilization. The areas over sulphide clay and some sulphate depositions may considerably increase the peat sulphur content. A proposal has been made to include the sulphur content monitoring in the cases where it exceeds 0.3 per cent. The trace elements may also bring about an increase in peat emissions if the deepest peat layers or polluted layers are burnt. The most important elements in this respect are Al, Fe, Mn, Pb, Zn, V, Ni, Hg, Cu, Cr, as well as As and U. The first ten because of the relatively high concentrations and last two because of pollution or toxocity and ore deposit factors. The peat hydrogen ion concentration has a positive correlation with copper and vanadium. The correlation is positive with the cobalt and nickel contents when the pH is low, and negative at a higher pH. A general peat type correlation shows maximum trace element contents in basal Carex peats with subsoil effects. The peat ash content and the Ti, Pb, V, Cr, Ni and S contents have positive correlations.

The recuperation of sulphuric acid out of contaminated solutions by electro electrodialysis; De recuperatie van zwavelzuur uit gecontamineerde oplossingen door elektro elektrodialyse

Energy Technology Data Exchange (ETDEWEB)

Cattoir, S

1997-05-01

The dismantling of a nuclear reactor results in large amounts of contaminated waste. The amount of waste is minimized by so-called decontamination processes. These decontamination processes result in decontaminated metal as well as contaminated effluents, containing acid and metal salts. Standard treatment of these effluents involves neutralisation of the acid using sodium hydroxide, resulting in the precipitation of hydroxides; and evaporation of the solvent. However, if the acid is extracted out of the decontamination effluents prior to neutralisation, this acid can be re-used in the decontamination process, substantially reducing the final waste. This report investigates the possibility of using Electro Electrodialysis (EED) for the extraction of 900 moles of sulphuric acid out of a 1 m{sup 3} contaminated solution, containing 22 kg of ferrous, chromous, cerous and nickel ions and 1000 moles of sulphuric acid. EED removes acids out of acid/salts solutions, using an electrolyser equipped with an anionic membrane: the acid-anion is displaced by migration through the membrane while the proton is displaced by electrolysis. This report gives a full description of the technique, the lab-scale apparatus, the analyses involved in studying the technique on lab-scale or monitoring it on full scale, the choice of electrode and membrane and of process parameters such as temperature and current density. On lab scale, EED can displace 90% of the acid out of the acid/salt solution just described, at a current density as high as 0.14 A.cm{sup -2}, at 50 degrees Celsius, if the cathode and the anode are of smoothed platina or of platinised titanium, and the anion selective membrane is the Neosepta AMH -membrane of Tokuyama. The study of EED still needs to be completed with a further study of metal deposition on the cathode, and a comparison of the technique to other (electro)membrane techniques.

Biological parameters in technogenic soils of a former sulphur mine

Science.gov (United States)

Siwik-Ziomek, Anetta; Brzezińska, Małgorzata; Lemanowicz, Joanna; Koper, Jan; Szarlip, Paweł

2018-04-01

This study was conducted on the soils originating from a reclamation area of the former sulphur mine in Tarnobrzeg, Poland. Soil was sampled 16 years after the completion of mining works with the open-pit method at Machów, as well as 7 years after sulphur mining via the `smelting' method in the Jeziórko mine was abandoned. Several biological parameters were examined: soil respiration, soil microbial biomass and the activity of rhodanese and arylsulphatase enzymes taking part in sulphur transformation within the site's soils. The soils showed a high total sulphur and sulphates content. The SO42- constituted a large fraction of total sulphur, in some cases, exceeding 80% or even 95% of total sulphur. The soil pH decreased due to the degrading effects of sulphur mining. In the soils studied from the locations with the lowest soil pH value, no activity of arylsulphatase was reported and the activity of rhodanese was lowest. The highest soil respiration values were recorded from the 0-5 cm layer in the areas covered with forest vegetation. A high soil respiration value at the waste heap at Machów wherein a very high concentration of Stot and SO42- was observed can be due to the ability of fungi to produce hyphal strands and to survive unfavourable conditions.

Assessing the suitability of Norway spruce wood as an environmental archive for sulphur

International Nuclear Information System (INIS)

Barrelet, T.; Ulrich, A.; Rennenberg, H.; Zwicky, C.N.; Kraehenbuehl, U.

2008-01-01

The aim of this study was to assess the suitability of Norway spruces (Picea abies L. Karst.) as an environmental archive for sulphur. For this purpose spruce trees were sampled in two distinct regions of Switzerland: the Alps and the Swiss Plateau, which differ significantly with respect to S immission. Wood samples were measured using two methods: LASER Ablation high resolution inductively coupled plasma mass spectrometry (LA-HR-ICP-MS) and inductively coupled plasma optical emission spectrometry (ICP-OES) after acid digestion. Independently corroborated by previous measurements of sulphur in peat bogs, the rise and fall of sulphur dioxide pollution in Switzerland appears to be reflected in spruce wood sulphur content. While the wood sulphur content profile of trees sampled in the Alps is relatively flat, the profiles of trees located on the Swiss Plateau display a characteristic sulphur peak. This corresponds to air pollution data in the different regions and indicates that the trees reacted on the changing S supply and recorded a pollution signal in the wood. - Norway spruce is a suitable archive for sulphur when physiological aspects and limitations are taken into account

Anionic Surfactant as a Corrosion Inhibitor for Synthesized Ferrous Alloy in Acidic Solution

Directory of Open Access Journals (Sweden)

Farida Kellou-Kerkouche

2013-01-01

Full Text Available The effect of temperature on the corrosion behaviour of a synthesized iron-based alloy in 1 N sulphuric acid solution has been examined by means of three electrochemical techniques. Thereafter, we studied the influence of an anionic surfactant (sodium dodecyl benzene sulfonate at various concentrations on the electrochemical behaviour of the ferrous alloy. The obtained results show that the temperature increase reduced the performance of the used alloy, in the acidic environment. Otherwise, the surfactant inhibits the alloy dissolution in the sulphuric acid, through its adsorption on the metal surface without modifying the mechanism of corrosion process. We also noticed that the highest inhibition effect is obtained at a concentration above its critical micelle concentration (CMC. Langmuir adsorption isotherm fits well with the experimental data.

Selective environmental stress from sulphur emitted by continental flood basalt eruptions

Science.gov (United States)

Schmidt, Anja; Skeffington, Richard; Thordarson, Thorvaldur; Self, Stephen; Forster, Piers; Rap, Alexandru; Ridgwell, Andy; Fowler, David; Wilson, Marjorie; Mann, Graham; Wignall, Paul; Carslaw, Ken

2016-04-01

Several biotic crises during the past 300 million years have been linked to episodes of continental flood basalt volcanism, and in particular to the release of massive quantities of magmatic sulphur gas species. Flood basalt provinces were typically formed by numerous individual eruptions, each lasting years to decades. However, the environmental impact of these eruptions may have been limited by the occurrence of quiescent periods that lasted hundreds to thousands of years. Here we use a global aerosol model to quantify the sulphur-induced environmental effects of individual, decade-long flood basalt eruptions representative of the Columbia River Basalt Group, 16.5-14.5 million years ago, and the Deccan Traps, 65 million years ago. For a decade-long eruption of Deccan scale, we calculate a decadal-mean reduction in global surface temperature of 4.5 K, which would recover within 50 years after an eruption ceased unless climate feedbacks were very different in deep-time climates. Acid mists and fogs could have caused immediate damage to vegetation in some regions, but acid-sensitive land and marine ecosystems were well-buffered against volcanic sulphur deposition effects even during century-long eruptions. We conclude that magmatic sulphur from flood basalt eruptions would have caused a biotic crisis only if eruption frequencies and lava discharge rates had been high and sustained for several centuries at a time.

Determination of the optimum standardised ileal digestible sulphur amino acids to lysine ratio in weaned pigs challenged with enterotoxigenic Escherichia coli

DEFF Research Database (Denmark)

Capozzalo, M. M.; Resink, J. W.; Htoo, J. K.

2017-01-01

This experiment tested the hypothesis that pigs challenged with an enterotoxigenic strain of E. coli (ETEC) would require a higher sulphur amino acids (SAA) to Lys ratio (SAA:Lys). Pigs (n = 120) weighing 7.4 ± 0.52 kg (mean ± SD) and weaned at 27 d (Pietrain genotype, mixed sex) were stratified...

Separation of uranium, molibdenum and vanadium in sulphuric solutions by extraction with alamine 336

International Nuclear Information System (INIS)

Floh, B.

1976-01-01

Alamine 336 - varsol - sulphuric acid-water system used for uranium, molibdenum and vanadium extraction, from sulphuric leaching and an appropriate plan for fractioning those elements are investigated. The behavior of cited elements in pure solutions followed by interaction that occurs in both bynary and tertiary systems are studied. Distribution coefficient is regarded for measuring such effects [pt

Strange and non-strange baryon and antibaryon production in sulphur-tungsten and sulphur-sulphur interactions at 200 A Gev/c

Energy Technology Data Exchange (ETDEWEB)

Holme, A.K.

1995-11-01

The author has studied production of strange and multistrange baryons and antibaryons in central sulphur-tungsten, sulphur-sulphur, and lead-lead interactions at relativistic energies. The spectra of strange baryons and antibaryons provide information about the dynamics of hadronic matter under the extreme conditions realised in these collisions. The particle ratios allow the degree and the nature of the flavour equilibrium to be studied, while the transverse mass distributions provide independent information of the temperatures achieved. 143 refs.

Strange and non-strange baryon and antibaryon production in sulphur-tungsten and sulphur-sulphur interactions at 200 A Gev/c

International Nuclear Information System (INIS)

Holme, A.K.

1995-11-01

The author has studied production of strange and multistrange baryons and antibaryons in central sulphur-tungsten, sulphur-sulphur, and lead-lead interactions at relativistic energies. The spectra of strange baryons and antibaryons provide information about the dynamics of hadronic matter under the extreme conditions realised in these collisions. The particle ratios allow the degree and the nature of the flavour equilibrium to be studied, while the transverse mass distributions provide independent information of the temperatures achieved. 143 refs

Uptake and metabolism of sulphur dioxide by Arabidopsis thaliana

NARCIS (Netherlands)

van der Kooij, T.A.W.; De Kok, L.J.; Haneklaus, S.; Schnug, E.

Arabidopsis thaliana (L.) Heynh. was exposed to various concentrations of SO2 during almost the entire life cycle. No negative effects of SO2 on shoot biomass production were observed. There was a linear relation between the deposition of SO2 and the atmospheric SO2 concentration. Sulphur

Use of stable sulphur isotopes to monitor directly the behaviour of sulphur in coal during thermal desulphurization

Science.gov (United States)

Liu, Chao-Li; Hackley, Keith C.; Coleman, D.D.

1987-01-01

A method has been developed using stable sulphur isotope analyses to monitor the behaviour of sulphur forms in a coal during thermal desulphurization. In this method, the natural stable isotopic composition of the pyritic and organic sulphur in coal is used as a tracer to follow their mobility during the desulphurization process. This tracer method is based on the fact that the isotopic compositions of pyritic and organic sulphur are significantly different in some coals. Isotopic results of pyrolysis experiments at temperatures ranging from 350 to 750 ??C indicate that the sulphur released with the volatiles is predominantly organic sulphur. The pyritic sulphur is evolved in significant quantities only when pyrolysis temperatures exceed 500 ??C. The presence of pyrite seems to have no effect on the amount of organic sulphur evolved during pyrolysis. The chemical and isotopic mass balances achieved from three different samples of the Herrin (No. 6) coal of the Illinois Basin demonstrate that this stable isotope tracer method is quantitative. The main disadvantage of this tracing technique is that not all coals contain isotopically distinct organic and pyritic sulphur. ?? 1987.

Effect of NPK fertilization and elemental sulphur on growth and yield of lowbush blueberry

Directory of Open Access Journals (Sweden)

M. STARAST

2008-12-01

Full Text Available The aim of the research was to determine the effect of fertilizers on the pH of former arable soils and on the growth and the yield of the lowbush blueberry (Vaccinium angustifolium Ait.. Lowbush blueberry fertilization experiments were established in 1999 at two locations – at Kärla, Saaremaa, West Estonia and at Vasula, Tartu County, South Estonia. Experimental sites were situated on different soils: soil pHKCl at Kärla was 5.5 and at Vasula 6.2. Elemental sulphur and acidifying fertilizers (ammonium sulfate, potassium sulfate and superphosphate were used in both plantations. Fertilizers were applied based on nutrient in the soil and sulphur was applied at 100 g m–2. Plant growth was recorded in 2001, 2002 and 2003. A positive influence of NPK fertilization on yield was found in both Kärla and Vasula, and yield were 336 g and 41 g higher compared to the control, respectively. The vegetative growth and yield of blueberry depended significantly on soil pH. Elemental sulphur increased soil acidity and on loamy sand soil did not increase plant productivity. The sulphur effect on soil pH began to decrease three years after application. Sulphur can be recommended to increase soil acidity in nutrient-rich soil but, not nutrient poor soil with light texture, where only NPK fertilizers were effective.;

Regional modelling of anthropogenic sulphur in Southeast Asia

Science.gov (United States)

Engardt, M.; Leong, C. P.

A co-operative research project between the Malaysian Meteorological Service (MMS) and the Swedish Meteorological and Hydrological Institute (SMHI) focussing on the usage of an atmospheric transport and chemistry model, has just been initiated. Here, we describe the main features of the dispersion model and discuss a first set of calculations in light of available measurements of sulphuric species in Southeast Asia. According to our results, anthropogenic sulphur concentrations and depositions are particularly high near the large cities of the region, around a metal smelter in the southern Philippines, and in a region extending from northern Vietnam into southeastern China. These areas coincide with the high-emissions regions of Southeast Asia and we tentatively conclude that regional transport of acidifying species is not as far-reaching as in the mid-latitudes. From our calculations, and from supporting measurements we conclude that most of rural Southeast Asia is not yet severely affected by anthropogenic sulphur, but given the rapid rate of economical development in this region the situation may deteriorate quickly. Areas that are particularly at risk include the large cities, northern Vietnam, most of central Thailand, most of peninsular Malaysia, eastern Sumatra and parts of Java, all of which receive total-sulphur depositions in excess of 0.5 g S m -2 yr -1. Our model simulates sulphate in precipitation in accordance with measurements, but it has a tendency to overestimate atmospheric SO 2. It remains to be investigated whether this is a problem in the model formulation or a result of unrepresentative sampling. An immediate continuation of this study should be performed with higher spatial resolution than the currently used 100×100 km 2. Other imperfections in this model study, which should be addressed in future work, include parameterised vertical transport in deep convective clouds, the influence of natural emissions (primarily from volcanoes) on the

Effects of Different Forms and Doses of Sulphur Application on Wheat

Directory of Open Access Journals (Sweden)

Halil Erdem

2016-11-01

Full Text Available Deficiency of sulphur (S is an important limiting factor of plant growth for sustainable agricultural production. The decline in sulphur dioxide emission, decrease in S-containing fertilizer consumption due to the high cost of S-fertilizers, breeding of new high yielding species are the well known causes of S-deficiency. A greenhouse experiment was conducted to investigate the effects of several doses of K2SO4-S, CaSO4-S and elemental-S applied on growth, shoot dry matter yield, S and N concentrations of wheat cultivar. The experiments were conducted in three soils differed from available S concentrations. Effects of different S-treatments (0, 25, 50 and 100 mg S kg-1 and S-forms had significant effects on shoot dry matter yields of plants. Sulphur from different S-sources did not increase shoot S-concentrations in Eskisehir and Konya soils, but increase was significant obtained in the Harran soil. Shoot S-concentration in Harran soil for zero K2SO4 treatment was 0.09%, the values were 0.22, 0.26 and 0.27% respectively for 25, 50 and 100 mg kg-1 treatments. The results indicated significant effects of S-treatments on plant growth and yield mostly based on soil properties, especially the available S-levels

Distribution of sulphur and trace elements in peat. A literature survey with some additional sulphur analyses

Energy Technology Data Exchange (ETDEWEB)

Huttunen, S; Karhu, M

1981-01-01

A survey on the literature and contemporary research was made on peat sulphur and trace element studies. Marked variance between different peatlands and peat types has been noted. The available information is still inadequate for generalizations or statistical analysis mainly due to methodological variations and temporal and spatial variations in results. At the moment, the criteria applied in peatland inventories and evaluations are inadequate with respect to peat quality determinations. To some extent the quality of fuel peat should be determined in a mire inventory prior to peatland utilization. The areas over sulphide clay and some sulphate depositions may considerably increase the peat sulphur content. A proposal has been made to include the sulphur content monitoring in the cases where it exceeds 0.3 per cent. The trace elements may also bring about an increase in peat emissions if the deepest peat layers or polluted layers are burnt. The most important elements in this respect are Al, Fe, Mn, Pb, Zn, V, Ni, Hg, Cu, Cr, as well as As and U. The first ten because of the relatively high concentrations and last two because of pollution or toxocity and ore deposit factors. The peat hydrogen ion concentration has a positive correlation with copper and vanadium. The correlation is positive with the cobalt and nickel contents when the pH is low, and negative at a higher pH. A general peat type correlation shows maximum trace element contents in basal Carex peats with subsoil effects. The peat ash content and the Ti, Pb, V, Cr, Ni, and S contents have positive correlations. (Refs. 290).

Spectrophotometric determination of tungsten with salicylic acid

International Nuclear Information System (INIS)

Goncalves, Z.C.

1976-10-01

The method comprises the complexation of tungsten with salicylic acid in concentrated sulphuric acid yielding a reddish color. The maximum absorbance of the complex lies within 410-420 nm, 420 nm being the chosen wavelenght. The final concentration of salicylic acid is 0,080 g/ml. The sensitivity is 0,13 μg W(%T) -1 ml -1 . Titanium, vanadium, rhenium, niobium and molybdenum interferes and must be separated, titanium being the strongest interferent. The separation procedures, advantages of the process, stoichiometric relations and equilibrium constant are discussed. (Author) [pt

Measurement of sulphur-35 in the coolant gas of the Windscale Advanced Gas-Cooled Reactor

International Nuclear Information System (INIS)

Sandalls, F.J.

1978-03-01

Sulphur is an important element in some food chains and the release of radioactive sulphur to the environment must be closely controlled if the chemical form is such that it is available or potentially available for entering food chains. The presence of sulphur-35 in the coolant gas of the Windscale Advanced Gas-Cooled Reactor warranted a study to assess the quantity and chemical form of the radioactive sulphur in order to estimate the magnitude of the potential environmental hazard which might arise from the release of coolant gas from Civil Advanced Gas-Cooled Reactors. A combination of gas chromatographic and radiochemical analyses revealed carbonyl sulphide to be the only sulphur-35 compound present in the coolant gas of the Windscale Reactor. The concentration of carbonyl sulphide was found to lie in the range 40 to 100 x 10 -9 parts by volume and the sulphur-35 specific activity was about 20 mCi per gramme. The analytical techniques are described in detail. The sulphur-35 appears to be derived from the sulphur and chlorine impurities in the graphite. A method for the preparation of carbonyl sulphide labelled with sulphur-35 is described. (author)

Isotopic equilibria between sulphur solute species at high temperature

International Nuclear Information System (INIS)

Robinson, B.W.

1978-01-01

Sulphur solute species in ore solutions and geothermal discharges include HSO 4 - , SO 4 2- , H 2 S, and HS - , as well as the ion-paired species, NaHS 0 , NaHSO 4 - and Na 2 SO 4 0 . Observed sulphate-sulphide fractionation factors and the rates of attainment of isotopic equilibrium are likely to depend on the nature of the sulphur species actually taking part in these isotopic equilibria. Preliminary experiments in alkaline solution (pH 10.1 at 20 0 C) were carried out in a gold cell. No significant isotope fractionation was observed between the SO 4 2- and HS - in 29 days at 200 0 C, 63days at 300 0 C, or 90 days at 250 0 C. However, similar experiments at 350 0 C in sealed gold capsules at room temperature pH 8.5 showed slow exchange(t( 1 / 2 ) was calculated to be 510 days for the SO 4 2- -HS - exchange reaction using the theoretical fractionation of 20.2 0 / 00 ). The addition of NaCl appeared to have no affect on the exchange. However, pH strongly controls the reaction rate, and exchange probably involves H 2 S and the HSO 4 - ion. Additional preliminary experiments were conducted with a fivefold increase in the sulphur concentration; a decrease in t( 1 / 2 ) to 142 days resulted. Some inter-relationship between sulphur concentration and exchange rate thus exists. The important controlling parameters of isotope exchange (temperature, pH, and ΣS) can be seen to have influenced exchange in natural systems.(auth.)

Corrosion Inhibition of Aluminium in Acid Media By Citrullus Colocynthis Extract

OpenAIRE

Chauhan, Rajkiran; Garg, Urvija; Tak, R. K.

2011-01-01

Inhibition of corrosion of aluminium in acid solution by methanol extract of Citrullus colocynthis plant has been studied using mass loss and thermometric measurements. It has been found that the plant extract act as a good corrosion inhibitor for aluminium in all concentrations of sulphuric and hydrochloric acid solution. The inhibition action depends on the concentration of acid and inhibitor. Results for mass loss and thermometric measurement indicate that inhibition efficiency increase wi...

Modelled transport and deposition of sulphur over Southern Africa

CSIR Research Space (South Africa)

Zunckel, M

2000-01-01

Full Text Available Ambient SO2 concentrations and atmospheric deposition of sulphur resulting from emissions on the industrialised highveld region of South Africa are estimated using the multi-scale atmospheric transport and chemistry (MATCH) modelling system...

Probing into the effects of a magnetic field on the electrode processes of iron in sulphuric acid solutions with dichromate based on the fundamental electrochemistry kinetics

International Nuclear Information System (INIS)

Lu Zhanpeng; Huang Delun; Yang Wu

2005-01-01

The effects of an applied magnetic field on the electrode processes of iron in sulphuric acid solutions with dichromate have been investigated by electrochemical measurements. Open circuit potentials, cathodic and anodic polarisation curves, values of polarisation resistance were measured in the presence or absence of a 0.4 T horizontal magnetic field (HMF). A potentiostatic polarisation plus magnetic field perturbation technique was used to study the effect of the magnetic field on open circuit corrosion. Cathodic reaction rates at open circuit potentials for iron in sulphuric acid solutions containing dichromate ions are controlled by both the electron-transfer process and the diffusion process. A magnetic field made the open circuit potential move in the positive direction, and changes of the open circuit potentials due to the magnetic field increase with increasing dichromate concentration. When iron was potentiostatically polarised at open circuit potentials in the absence of a magnetic field, a cathodic current was observed after a magnetic field was imposed. Such cathodic currents induced by the magnetic field increases with increasing dichromate concentration. The positive shifts of open circuit potential, the decrease of polarisation resistance, and the occurrence of cathodic currents induced by the magnetic field are caused by the accelerating effect of magnetic field on the cathodic diffusion process. Measured current densities showed lower, equal, or higher values in the presence of the magnetic field than those in the absence of a magnetic field at certain anodic potentials. This effect of the magnetic field is related to the contribution of the cathodic and anodic reactions to the measured current and the types of rate-determining steps for each reaction at certain potentials. The applied magnetic field significantly decreased the polarisation resistance. The experimental results in this paper are formulated based on the fundamental electrochemistry

Sulphur in liquid fuels 2002

Energy Technology Data Exchange (ETDEWEB)

Guthrie, J. [Environment Canada, Gatineau, PQ (Canada). Fuels Div., Oil, Gas and Energy Branch ; Sabourin, R. [Carleton Univ., Ottawa, ON (Canada)

2003-08-01

Environment Canada has developed new regulations for sulphur content in fuels in an effort to align with requirements recently passed by the U.S. Environmental Protection Agency. This report summarizes data regarding sulphur content in liquid fuels for the year 2002. The requirements of the Sulphur in Gasoline Regulation came into effect in 2002, limiting the average sulphur content of gasoline to 150 mg/kg. In January 2005, a 30 mg/kg average limit will come into effect. Also, in July 2002, the Sulphur in Diesel Fuel Regulation stipulated a maximum limit of 500 mg/kg for on-road diesel fuel. The new regulation continues this limit until mid-2006 at which time a 15 mg/kg limit will come into effect for on-road diesel fuel. Nationally, the average sulphur content in gasoline in 2002 was 246 mg/kg, which was 14.3 per cent lower than in 2001. The data covers the period from January 1 to December 31, 2002 and was obtained from petroleum refineries and importing companies that are required to submit quarterly information to the regional office of Environment Canada. Failure to comply results in penalties. The report includes data for aviation turbo fuel, motor gasoline, aviation gasoline, kerosene oil, low-sulphur diesel fuel, diesel fuel, light fuel oil, and heavy fuel oil. 16 tabs., 17 figs., 7 appendices.

Effect of elemental sulphur and compost on pH, electrical ...

African Journals Online (AJOL)

Safir

2012-01-19

Jan 19, 2012 ... 42/34. T.N.V. 4.5. P (mg kg-1) ... and extracted with 2.0 M HCl) were measured with similar methods ... react with carbonate in calcareous soil and neutralize it. Neilson ... oxidation in soil, the sulphuric acid formed reacted with.

Selective removal of chromium from sulphuric acid leach liquor of ilmenite ore by solvent extraction with trioctylamine

Directory of Open Access Journals (Sweden)

E.O. Olanipekun

2000-12-01

Full Text Available The selective removal of chromium, a trace impurity that degrades the whiteness of titanium(IV oxide pigments, from sulphuric acid leach liquor of ilmenite, was investigated by solvent extraction with xylene solutions of trioctylamine. Important factors of commercial significance affecting the extraction operation have been examined. More than 99% of the chromium was selectively removed in multiple batch extractions from the leach liquor and titanium losses were minimal (< 1%. The chromium content of extracted solutions was reduced to less than 1 ppm and thermal hydrolysis of these solutions yielded white titanium(IV oxide pigments that are suitable for use in the coatings pigment industry.

Volatile sulphur compounds in morning breath of human volunteers.

NARCIS (Netherlands)

Snel, J.; Burgering, M.; Smit, B.; Noordman, W.; Tangerman, A.; Winkel, E.G.; Kleerebezem, M.

2011-01-01

OBJECTIVE: morning breath contains elevated concentrations of volatile sulphur components (VSCs). Therefore, morning breath is recognised as a surrogate target for interventions on breath quality. Nevertheless, factors influencing morning breath are poorly understood. Our aim was to evaluate

Volatile sulphur compounds in morning breath of human volunteers

NARCIS (Netherlands)

Snel, Johannes; Burgering, Maurits; Smit, Bart; Noordman, Wouter; Tangerman, Albert; Winkel, Edwin G.; Kleerebezem, Michiel

Objective: Morning breath contains elevated concentrations of volatile sulphur components (VSCs). Therefore, morning breath is recognised as a surrogate target for interventions on breath quality. Nevertheless, factors influencing morning breath are poorly understood. Our aim was to evaluate

Chemical dosimetry at less than 1000 rad: aqueous trimesic acid solutions

International Nuclear Information System (INIS)

Matthews, R.W.; Wilson, J.G.

1981-01-01

Aqueous solutions of trimesic acid were investigated for possible use as a chemical dosimeter. In aerated 10 -2 M sulphuric acid solution containing 10 -3 M trimesic acid, a highly fluorescent product is formed with its maximum fluorescence at 450nm when excited by 350nm light. The product has fluorescence characteristics very similar to quinine in 0.05 M sulphuric acid. The fluorescence intensity is linear with dose in the range 1-1000 rad and a precision of +-2% was obtained from a number of runs. Solutions are stable for at least several days before and after irradiation. The yield is little affected by moderate changes in trimesic acid concentration, oxygen concentration, water purity, energy of radiation and irradiation temperature. The small dependence of the yield on dose rate and the effect of measurement temperature on the fluorescence signal have been quantified. The most significant factor affecting the fluorescence signal is the hydrogen ion concentration of the solution. In aerated neutral and alkaline (pH 10) solutions, hydroxytrimesic acid (HTMA) is formed with G(HTMA) equal to 2.07 +- 0.04 and 2.21 +- 0.04, for 10 -3 M trimesate. In these solutions, G(HTMA) increases appreciably with increase in the trimesate concentration. The main fluorescent product formed in irradiated acid solutions was not identified but it was not HTMA. (author)

Abatements of reduced sulphur compounds, colour, and organic matter from indigo dyeing effluents by electrocoagulation.

Science.gov (United States)

Tünay, Olcay; Simşeker, Merve; Kabdaşli, Isik; Olmez-Hanci, Tugba

2014-08-01

In the present study, the treatability of indigo dyeing effluents by the electrocoagulation (EC) process using stainless steel electrodes was experimentally investigated. The samples used were concentrated with main pollutant parameters of chemical oxygen demand (COD) (1000-1100 mg/L), reduced sulphur species (over 2000 mg SO2-(3)/L), and colour (0.12-0.13 1/cm). The study focused on the effect of main operation parameters on the EC process performance in terms of abatement of reduced sulphur compounds as well as decolourization and organic matter reduction. Results indicated that the performance of EC proved to be high providing total oxidation of the reduced sulphur compounds, almost complete decolourization, and COD removal up to 90%. Increasing applied current density from 22.5 to 45 mA/cm2 appreciably improved abatement of the reduced sulphur compounds for Sample I, but a further increase in the applied current density to 67.5 mA/cm2 did not accelerate the conversion rate to sulphate. The process performance was adversely affected by increasing initial concentration of the reduced sulphur compounds. Decolourization and organic matter removal efficiency enhanced with increasing applied current density. The main removal mechanism of the reduced sulphur compounds by EC was explained as conversion to sulphate via oxidation. Conversion rate to sulphate fitted pseudo-first-order kinetics very well.

Acid-digestion plant for plutonium-contaminated waste at the Swiss Federal Institute for Reactor Research

International Nuclear Information System (INIS)

Guentensperger, M.A.

1981-01-01

At the Swiss Federal Institute for Reactor Research (EIR), plutonium-contaminated material (PCM) is accumulated in the ''hot-laboratory''. Acid digestion has been chosen for conditioning the combustible PCM at EIR. The acid-digestion process is based on the carbonization and oxidative decomposition of the PCM by means of concentrated sulphuric and nitric acids at temperatures around 250 0 C. The design study for the acid-digestion plant (ADA) for EIR has almost been completed, and the detailed design has begun. The shredded waste will be fed batchwise on to the surface of hot sulphuric acid in the digester tray where carbonization occurs. The oxidation of the carbonized particles to gaseous products occurs in the heater vessel where nitric acid is added to accelerate the reaction. The inorganic residues of the digested PCM accumulate in the heater vessel as suspended particles. Periodically the acid is drained and the solid residue is separated. The gaseous effluents pass through a battery of oxidation/absorption columns where SO 2 and NOsub(x) are oxidized to sulphuric and nitric acids, respectively. These acids are almost entirely absorbed in the washing solution which is fed continuously to the acid-rectification system. The separated and reconcentrated acids are reused. For safety reasons the ADA will be semi-automatic; the principal alarms are transmitted to a control centre. Automatic shut-down is achieved by cutting off the heater current and adding cold sulphuric acid. (author)

Sulphur simulations for East Asia using the MATCH model with meteorological data from ECMWF

Energy Technology Data Exchange (ETDEWEB)

Engardt, Magnuz

2000-03-01

As part of a model intercomparison exercise, with participants from a number of Asian, European and American institutes, sulphur transport and conversion calculations were conducted over an East Asian domain for 2 different months in 1993. All participants used the same emission inventory and simulated concentration and deposition at a number of prescribed geographic locations. The participants were asked to run their respective model both with standard parameters, and with a set of given parameters, in order to examine the different behaviour of the models. The study included comparison with measured data and model-to-model intercomparisons, notably source-receptor relationships. We hereby describe the MATCH model, used in the study, and report some typical results. We find that although the standard and the prescribed set of model parameters differed significantly in terms of sulphur conversion and wet scavenging rate, the resulting change in atmospheric concentrations and surface depositions only change marginally. We show that it is often more critical to choose a representative gridbox value than selecting a parameter from the suite available. The modelled, near-surface, atmospheric concentration of sulphur in eastern China is typically 5- 10 {mu}g S m{sup -3}, with large areas exceeding 20 {mu}g S m{sup -3}. In southern Japan the values range from 2-5 {mu}g S m{sup -3} . Atmospheric SO{sub 2} dominates over sulphate near the emission regions while sulphate concentrations are higher over e.g. the western Pacific. The sulphur deposition exceeds several g sulphur m{sup -2} year{sup -1} in large areas of China. Southern Japan receives 03-1 g S m{sup -2} year{sup -1}. In January, the total wet deposition roughly equals the dry deposition, in May - when it rains more in the domain - total wet deposition is ca. 50% larger than total dry deposition.

Three-decade changes in chemical composition of precipitation in Guangzhou city, southern China: has precipitation recovered from acidification following sulphur dioxide emission control?

Directory of Open Access Journals (Sweden)

Yunting Fang

2013-09-01

Full Text Available We examined if precipitation had recovered from acidification in Guangzhou, the third biggest city in China, and if sulphur deposition in precipitation had decreased, and to what extent if yes, following abatement strategies in sulphur dioxide (SO2 emission and energy use implemented since 2001. SO2 emissions were decreasing steadily since 2001, but a marked recovery of precipitation acidity occurred only since 2005; precipitation pH values decreased from 4.65 in 2001 to 4.34 in 2005 and then increased to 5.08 in 2010, while in the same period acid rain (pH<5.6 frequency increased from 70% to 81% and then decreased to 48%. During this period, the change in pH value and sulphate concentration more reflected the patterns of SO2 emission at provincial and national scales than at the local scale, suggesting that precipitation chemical composition was largely controlled by the emissions of pollutants from surrounding areas of the study city. Since 2001, sulphate deposition in precipitation decreased significantly (by 40% but nitrogen deposition remained unaltered. More importantly, the current sulphur (43 kg S ha−1 yr−1 as sulphate and nitrogen depositions (35 kg N ha−1 yr−1 as ammonium plus nitrate in 2010 were still among the highest in China. These results highlight the fact that ambient sulphur and nitrogen deposition still pose a threat to the health of both terrestrial and aquatic ecosystems. Precipitation may become more acidified in the future because the deposition of alkaline dusts containing calcium is also likely to decrease with stricter SO2 emission control policy and reduced construction activities. Additionally, we recommend that a reduction of emissions of nitrogen and chlorine bearing pollutants is urgently required for complete control on acid deposition.

A new biological method for preparing certain sulphurated substances labelled with S35

International Nuclear Information System (INIS)

Chapeville, F.; Maier-Huser, H.; Fromageot, P.

1962-01-01

Previous investigations have shown that the yolk-sac of embryonic bird's eggs can be used to produce the following reactions: (a) reduction of sulphate to sulphite; (b) fixation of the sulphite on the carbon chain produced by the desulf-hydration of l-cysteine, with formation of l-cysteic acid; (c) decarboxylation of the l-cysteine acid into taurine. The enzymatic system which causes reaction (b) has been purified. It also acts as a catalyst in the sulphur-exchange between the cysteine and the mineral sulphide. The authors have utilized these data in preparing sulphurated substances labelled with S 35 : taurine S 35 , l-cysteine S 35 and l-cysteic acid S 35 . For each of the three, they discuss the chemical reactions involved, the methods of preparation, the experimental conditions of extraction and purity-control, together with the yields and specific activities obtained. (authors) [fr

Interrogating trees for isotopic archives of atmospheric sulphur deposition and comparison to speleothem records

International Nuclear Information System (INIS)

Wynn, P.M.; Loader, N.J.; Fairchild, I.J.

2014-01-01

Palaeorecords which depict changes in sulphur dynamics form an invaluable resource for recording atmospheric pollution. Tree rings constitute an archive that are ubiquitously available and can be absolutely dated, providing the potential to explore local- to regional-scale trends in sulphur availability. Rapid isotopic analysis by a novel “on-line” method using elemental analyser isotope ratio mass spectrometry (EA-IRMS) is developed, achieving sample precision of <0.4‰ using sample sizes of 40 mg wood powder. Tree cores from NE Italy show trends in pollution, evidenced through increasing concentrations of sulphur towards the youngest growth, and inverse trends in sulphur isotopes differentiating modern growth with light sulphur isotopes (+0.7‰) from pre-industrial growth (+7.5‰) influenced by bedrock composition. Comparison with speleothem records from the same location demonstrate replication, albeit offset in isotopic value due to groundwater storage. Using EA-IRMS, tree ring archives form a valuable resource for understanding local- to regional-scale sulphur pollution dynamics. - Highlights: • Sulphur isotopes from tree rings are analysed using ‘on-line’ EA combustion. • Isotopes differentiate modern growth influenced by pollution from pre-industrial growth. • Biogeochemical cycling imparts minimal delay in sulphur incorporation into tree rings. • Trends in pollution are replicated between speleothems and trees from the same location. - Sulphur isotopes extracted from tree ring records are used to identify twentieth century pollution dynamics at the local- to regional-scale

Adsorption of sulphuric acid on smectite from acidic aqueous solutions Adsorção de ácido sulfúrico em esmectita de soluções aquosas ácidas

Directory of Open Access Journals (Sweden)

E. L. Tavani

1999-05-01

Full Text Available The adsorption of sulphuric acid on smectite from acidic aqueous solutions was studied. The amounts of cations dissolved in each equilibrium solution were determined by chemical analysis. Simultaneously, the original smectite and the smectite after each test were characterized by infrared, X-ray diffraction and swelling index. The results obtained permitted us to determine that the substitutions of the exchange cations and the chemical attack occurred at very different acid concentrations and treatment times. It was established that during the acid treatment of the smectite, a progressive damage of its crystalline structure was produced. Finally, the influences of the substitution of exchange cations and of the chemical attack in the swelling index were determined.A adsorção de ácido sulfúrico em esmectita de soluções aquosas ácidas é estudada. As concentrações de cátions dissolvidos em cada solução em equilíbrio foram determinadas por análise química. As esmectitas original e após cada teste foram simultaneamente caracterizadas por infravermelho, difração de raios X e índice de crescimento. Os resultados obtidos permitiram determinar que as substituições dos cátions de troca e o ataque químico ocorreram em diferentes concentrações de ácido e tempos de tratamento. Foi verificado que durante o tratamento em ácido da esmectita foi produzido um dano progressivo da sua estrutura cristalina. Finalmente foram determinadas as influências da substituição dos cátions de troca e do ataque químico no índice de crescimento.

Sulphur removal from used automotive lubricating oil by ionizing radiation

International Nuclear Information System (INIS)

Scapin, Marcos Antonio; Duarte, Celina Lopes; Sato, Ivone Mulako

2007-01-01

Following the worldwide evolution with the purpose of a higher control of vehicular emissions, the specialists have looked for clean technologies and efficient procedures to make vehicular emissions free of pollutants. Much attention is given to the sulphur concentration in the gasoline, diesel and lubricating oils. The ionizing radiation is a promising technology for the removal of this pollutant when compared to other conventional treatment methods. In this work, the ionizing radiation was used to remove in significant levels the presence of sulphur in automotive motor oil. A 1000 mL sample of used automotive lubricating oil from a gas station was collected. This sample was fractioned and irradiated with 10, 20 50, 100, 200 and 500 kGy doses in a 60 Co irradiator (GAMMACELL-220 - 12 kCi). The 50 and 70% (v/v) of MilliQ water and 30% (v/v) of hydrogen peroxide was used to improve the radiolysis The sulphur element before and after the irradiation was determined by X-ray fluorescence technique (WDXRF) using the Fundamental Parameters Method. The results showed approximately 70% sulphur removal at 500 kGy irradiation dose with 70% (v/v) of MilliQ water addition. (author)

Integrated laboratory scale demonstration experiment of the hybrid sulphur cycle and preliminary scale-up

International Nuclear Information System (INIS)

Leybros, J.; Rivalier, P.; Saturnin, A.; Charton, S.

2010-01-01

The hybrid sulphur cycle is today one of the most promising processes to produce hydrogen on a massive scale within the scope of high temperature nuclear reactors development. Thus, the Fuel Cycle Technology Department at CEA Marcoule is involved in studying the hybrid sulphur process from a technical and economical performance standpoint. Based on mass and energy balance calculations, a ProsimPlus TM flow sheet and a commercial plant design were prepared. This work includes a study on sizing of the main equipment. The capital cost has been estimated using the major characteristics of main equipment based upon formulae and charts published in literature. A specific approach has been developed for electrolysers. Operational costs are also proposed for a plant producing 1000 mol/s H 2 . Bench scale and pilot experiments must focus on the electrochemical step due to limited experimental data. Thus, a pilot plant with a hydrogen capacity of 100 NL/h was built with the aim of acquiring technical and technological data for electrolysis. This pilot plant was designed to cover a wide range of operating conditions: sulphuric acid concentrations up to 60 wt.%, temperatures up to 100 deg. C and pressures up to 10 bar. New materials and structures recently developed for fuel cells, which are expected to yield significant performance improvements when applied to classical electrochemical processes, will be tested. All experiments will be coupled with phenomenological simulation tools developed jointly with the experimental programme. (authors)

Removing sulphur oxides from a fluid stream

Science.gov (United States)

Katz, Torsten; Riemann, Christian; Bartling, Karsten; Rigby, Sean Taylor; Coleman, Luke James Ivor; Lail, Marty Alan

2014-04-08

A process for removing sulphur oxides from a fluid stream, such as flue gas, comprising: providing a non-aqueous absorption liquid containing at least one hydrophobic amine, the liquid being incompletely miscible with water; treating the fluid stream in an absorption zone with the non-aqueous absorption liquid to transfer at least part of the sulphur oxides into the non-aqueous absorption liquid and to form a sulphur oxide-hydrophobic amine-complex; causing the non-aqueous absorption liquid to be in liquid-liquid contact with an aqueous liquid whereby at least part of the sulphur oxide-hydrophobic amine-complex is hydrolyzed to release the hydrophobic amine and sulphurous hydrolysis products, and at least part of the sulphurous hydrolysis products is transferred into the aqueous liquid; separating the aqueous liquid from the non-aqueous absorption liquid. The process mitigates absorbent degradation problems caused by sulphur dioxide and oxygen in flue gas.

Experiences in sulphur capture in a 30 MWth Circulating Fluidized Bed boiler under oxy-combustion conditions

International Nuclear Information System (INIS)

Gómez, M.; Fernández, A.; Llavona, I.; Kuivalainen, R.

2014-01-01

CO 2 and SO 2 from fossil fuel combustion are contributors to greenhouse effect and acid rain respectively. Oxy-combustion technology produces a highly concentrated CO 2 stream almost ready for capture. Circulating Fluidized Bed (CFB) boiler technology allows in-situ injection of calcium-based sorbents for efficient SO 2 capture. CIUDEN's 30 MWth CFB boiler, supplied by Foster Wheeler and located at the Technology Development Centre for CO 2 Capture and Transport (es.CO 2 ) in Spain, is the first of its kind for executing test runs at large pilot scale under both air-combustion and oxy-combustion conditions. In this work, SO 2 emissions under different scenarios have been evaluated. Variables such as limestone composition, Ca/S molar ratio and bed temperature among others have been considered along different test runs in both air-combustion and oxy-combustion conditions to analyse its influence on SO 2 abatement. Fly and bottom ash, together with flue gas analysis have been carried-out. Desulphurization performance tests results are presented. - Highlights: •Sulphur capture efficiency (%) was higher in oxy-combustion compared to air-combustion in a 30 MW thermal CFB boiler using anthracite and limestone as sulphur sorbent. •For a Ca/S molar ratio higher than 2.6 there was barely any improvement on sulphur capture efficiency for both air-combustion and oxy-combustion conditions in a 30 MW thermal CFB boiler using anthracite and limestone as sulphur sorbent. •Optimum temperature for sulphur capture at a fixed Ca/S molar ratio is around 880–890 °C under oxy-combustion conditions and for anthracite coal with limestone as sorbent in a 30 MW thermal CFB boiler

LEACH ARCILLAS ACTIVATED PARTIAL ACID SULFURICO

OpenAIRE

Romero Y Otiniano, P.; Pizarra Cabrera, R.

2014-01-01

This work is concerned with the activation of calcium bentonite from Junín- Perú (with a moisture content of 24.1% and an average of particle size 40 µ ) with sulphuric acid. The parameters studied are the ratio of bentonite to acid solution, acid concentration and reaction time to boiling temperatura of the mixture. The optimum conditions obtained are the following: 0.47 kg. of bentonite/kg. of acid solution to 4.8 N, 4 h of treatment to 104 ºC and the conversion of 45.6% alumina and 73.5% o...

Atmospheric dry and wet deposition of sulphur and nitrogen species and assessment of critical loads of acidic deposition exceedance in South Africa

Directory of Open Access Journals (Sweden)

Stuart J. Piketh

2011-03-01

Full Text Available We tested the hypothesis that acidic atmospheric pollution deposition, originating from the South African central industrial area, poses an environmental threat across a larger region within the dispersal footprint. A network of 37 passive monitoring sites to measure SO₂ and NO₂ was operated from August 2005 to September 2007. The area extended over the entire northern and eastern interior of South Africa. Monitoring locations were chosen to avoid direct impacts from local sources such as towns, mines and highways. Dry deposition rates of SO₂ and NO₂ were calculated from the measured concentrations. Concentrations of sulphur and nitrogen species in wet deposition from a previous study were used in conjunction with measured rainfall for the years 2006 and 2007 to estimate the wet deposition over the region. The calculated total (non-organic acidic deposition formed the basis for an assessment of exceedance of critical loads based on sensitivity of the regional soils. Regional soil sensitivity was determined by combining two major soil attributes available in the World Inventory of Soil Emission Potentials (International Soil Reference and Information Centre. Results indicate that certain parts of the central pollution source area on the South African Highveld have the potential for critical load exceedance, while limited areas downwind show lower levels of exceedance. Areas upwind and remote areas up and downwind, including forested areas of the Drakensberg escarpment, do not show any exceedance of the critical loads.

Pyroclastic sulphur eruption at Poas Volcano, Costa Rica

Energy Technology Data Exchange (ETDEWEB)

Francis, P.W.; Thorpe, R.S.; Brown, G.C.; Glasscock, J.

1980-01-01

The recent Voyager missions to Jupiter have highlighted the role of sulphur in volcanic processes on io. Although fumarolic sulphur and SO/sub 2/ gas are almost universal in terrestrial active volcanoes, and rare instances of sulphur lava flows have been reported, sulphur in a pyroclastic form has only been described from Poas Volcano, Costa Rica. Here we amplify the original descriptions by Bennett and Raccichini and describe a recent eruption of pyroclastic sulphur scoria and ejected blocks that are characterised by miniature sulphur stalactites and stalagmites.

Simultaneous analysis of gaseous and particulate sulphur in the atmosphere by x-ray fluorescence spectrometry

International Nuclear Information System (INIS)

Matsuda, Yatsuka; Mamuro, Tetsuo

1975-01-01

An analytical technique for the simultaneous measurements of the atmospheric concentrations of SO 2 gas and sulphur absorbed by aerosol particles has been developed. Aerosol particles are collected on membrane filter and at the same time SO 2 gas is captured on alkali impregnated filter. The sulphur content in each filter is measured by an energy dispersive X -ray fluorescence spectrometer consisting of a Si(Li) semiconductor detector connected to a multi-channel pulse height analyzer and an excitation source of 55 Fe. Two methods are acceptable for the determination of the sulphur content in impregnated filter by X-ray fluorescence analysis. In the first method X-ray fluorescence analysis is made after the collected sulphur gas diffused and distributed uniformly enough throughout the filter, and in the second method X-ray fluorescence analysis gas to be finished before the diffusion of the collected sulphur becomes appreciable. (author)

Acid digestion of organic materials

International Nuclear Information System (INIS)

Capp, P.D.

1988-01-01

To overcome the high temperatures involved in straight incineration of organic waste and the difficulty of extracting actinides from the ash various research establishments throughout the world, including Winfrith and Harwell in the UK, have carried out studies on an alternative chemical combustion method known as acid digestion. The basis of the technique is to digest the waste in concentrated sulphuric acid containing a few percent of nitric acid at a temperature of about 250 0 C. Acid digestion residues consist mainly of non-refractory inorganic sulphates and oxides from which any actinide materials can easily be extracted. (author)

Changes in the content of water-soluble sulphur in the soil after an application of straw and elemental sulphur

Directory of Open Access Journals (Sweden)

Pavel Ryant

2007-01-01

Full Text Available The changes in the content of water-soluble sulphur in the soil after the application of straw and elemental sulphur (ES were explored in a 2-year vegetation pot experiment. The following variants were included in the experiment: 1 unfertilised control; 2 wheat straw; 3 rape straw; 4 ES; 5 wheat straw + ES; 6 rape straw + ES. The two types of straw were applied in a dose of 32 g of dry matter and elemental sulphur was applied in a dose of 0.42 g per pot, i.e. 6 kg of soil. The unsatisfactory C:N ratio in the straw was optimised to 25:1 by adding nitrogen in urea. Soil samples were taken prior to sowing of the model plant (spring wheat in 2005 and white mustard in 2006 and then in regular monthly intervals until harvesting (5 times a year. The content of water-soluble sulphur in the soil was evaluated by multifactorial analysis of variance monitoring the effect of the crop, date of soil sampling, application of straw and elemental sulphur.The contents of water-soluble sulphur differed statistically significantly (P > 0.999 when growing the individual model plants. When growing white mustard in 2006 the amount of available sulphur was by 1/5 higher and could have been partly affected by the warm year 2006, as compared to 2005 when spring wheat was grown. Significant differences (P > 0.999 were also discovered among the dates of soil sampling; higher values were detected before the sowing of model plants, i.e. after incubation in the winter, during vegetation the content of water-soluble sulphur decreased and sulphur showed the significantly highest values at the harvest of model plants. When wheat straw was applied the sulphur content did not increase and this may be associated with the wide C:S ratio, whereas after the application of rape straw the content of water-soluble sulphur increased by one third more than in the unfertilised control. The application of elemental sulphur also significantly increased the amount of water-soluble sulphur in

Determination of the optimum standardised ileal digestible sulphur amino acids to lysine ratio in weaned pigs challenged with enterotoxigenic Escherichia coli

DEFF Research Database (Denmark)

Capozzalo, M. M.; Resink, J. W.; Htoo, J. K.

2017-01-01

This experiment tested the hypothesis that pigs challenged with an enterotoxigenic strain of E. coli (ETEC) would require a higher sulphur amino acids (SAA) to Lys ratio (SAA:Lys). Pigs (n = 120) weighing 7.4 ± 0.52 kg (mean ± SD) and weaned at 27 d (Pietrain genotype, mixed sex) were stratified...... into 1 of 6 treatments based on weaning weight, sex and genotype for the F4 fimbria receptor (n = 20). Five diets were formulated with increasing ratios of standardised ileal digestible (SID) sulphurSAA:Lys. Pigs were housed in pens of 4 during an adaptation period of 6 d after which time pigs were...... housed individually. Pigs fed different SID SAA:Lys levels were infected with ETEC (5 mL, 1.13 × 108 CFU/mL, serotype O149:K91:K88) on d 8, 9, and 10 after weaning. The sixth diet, which contained 0.55 SID SAA:Lys and corresponded to current NRC recommendations, was allocated to 2 groups of pigs either...

Yeast strains role on the sulphur dioxyde combinations of wines obtained from noble rot and raisining grapes

Directory of Open Access Journals (Sweden)

Isabelle Masneuf-Pomarède

2000-03-01

Full Text Available The influence of four industrial and indigenous yeast strains on the sulphur dioxide combinations of wines obtained from noble rot and raisining grapes is studied in different growth of the Sauternes area and one growth in the Jurançon area. The analysis of ketonic compounds (pyruvic acid and 2-oxo-glutaric acid, acetaldehyde and PC50 on the wines clearly showed significant statistical difference between the yeast strains for the sulphur dioxide combination. By adding the same dosage of sulphiting, the free SO2 levels are variable depending on the yeast strain used. One strain (Zymaflore ST, isolated from a spontaneous fermentation of a botrytised must, giving wines with low PC50 values, is well adapted for the noble rot must vinification. The choice of the yeast strain is a parameter of importance to limit the sulphur dioxide amount in the wines.

Effect of Adenine Concentration on the Corrosion Inhibition of Aisi ...

African Journals Online (AJOL)

This gave a surface coverage of 0.8956 and corrosion penetration rate of 0.022132mm/yr. Hence, the best adenine concentration for the corrosion inhibition of alloys 304L in 1.0M sulphuric acid solution to obtain optimum inhibition efficiency is 0.011M. Keywords: Corrosion, AISI 304L Steel, Inhibition efficiency, Degree of ...

Passive remediation of acid mine drainage using cryptocrystalline magnesite: a batch experimental and geochemical modelling approach

CSIR Research Space (South Africa)

Masindi, Vhahangwele

2015-10-01

Full Text Available Acid mine drainage is generated when mining activities expose sulphidic rock to water and oxygen leading to generation of sulphuric acid effluents rich in Fe, Al, SO (Sup4) and Mn with minor concentrations of Zn, Cu, Mg, Ca, Pb depending...

Sulphur capture by co-firing sulphur containing fuels with biomass fuels - optimization

International Nuclear Information System (INIS)

Nordin, A.

1992-12-01

Previous results concerning co-firing of high sulphur fuels with biomass fuels have shown that a significant part of the sulphur can be absorbed in the ash by formation of harmless sulphates. The aim of this work has been to (i) determine the maximum reduction that can be obtained in a bench scaled fluidized bed (5 kW); (ii) determine which operating conditions will give maximum reduction; (iii) point out the importance and applicability of experimental designs and multivariate methods when optimizing combustion processes; (iv) determine if the degree of sulphur capture can be correlated to the degree of slagging, fouling or bed sintering; and (v) determine if further studies are desired. The following are some of the more important results obtained: - By co-firing peat with biomass, a total sulphur retention of 70 % can be obtained. By co-firing coal with energy-grass, the total SO 2 emissions can be reduced by 90 %. - Fuel feeding rate, amount of combustion air and the primary air ratio were the most important operating parameters for the reduction. Bed temperature and oxygen level seem to be the crucial physical parameters. - The NO emissions also decreased by the sulphur reducing measures. The CO emissions were relatively high (130 mg/MJ) compared to large scale facilities due to the small reactor and the small fluctuations in the fuel feeding rate. The SO 2 emissions could however be reduced without any increase in CO emissions. - When the reactor was fired with a grass, the bed sintered at a low temperature ( 2 SO 4 and KCl are formed no sintering problems were observed. (27 refs., 41 figs., 9 tabs., 3 appendices)

Thermal stability studies on atomically clean and sulphur passivated InGaAs surfaces

Energy Technology Data Exchange (ETDEWEB)

Chauhan, Lalit; Hughes, Greg [School of Physical Sciences, Dublin City University, Glasnevin, Dublin 9 (Ireland)

2013-03-15

High resolution synchrotron radiation core level photoemission measurements have been used to study the high temperature stability of sulphur passivated InGaAs surfaces and comparisons made with atomically clean surfaces subjected to the same annealing temperatures. Sulphur passivation of clean InGaAs surfaces prepared by the thermal removal of an arsenic capping layer was carried out using an in situ molecular sulphur treatment in ultra high vacuum. The elemental composition of the surfaces of these materials was measured at a series of annealing temperatures up to 530 C. Following a 480 C anneal In:Ga ratio was found to have dropped by 33% on sulphur passivated surface indicating a significant loss of indium, while no drop in indium signal was recorded at this temperature on the atomically InGaAs surface. No significant change in the As surface concentration was measured at this temperature. These results reflect the reduced thermal stability of the sulphur passivated InGaAs compared to the atomically clean surface which has implications for device fabrication. (Copyright copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effectiveness of Higher Fatty Acids C8, C10 and C12, Dimethyl Dicarbonate and Sulphur Dioxide for Inhibition of Re-fermentation and Malolactic Activities in Wine

Directory of Open Access Journals (Sweden)

Mojmír Baroň

2014-01-01

Full Text Available The issue of preventing the re-fermentation and protection against undesirable malolactic fermentation (MLF in order to safe content of acids in wine is very complicated. In this paper the saturated higher fatty acids (HFA – C8, C10 and C12, dimethyldicarbonate (DMDC and sulphur dioxide (SO2 were tested. The re-fermentation test showed the strongest inhibition power at ratio 2:8, 1:9 and 0:10 as C8:C10 acids – 65 days without re-fermentation. MLF experiments confirmed that addition of SO2 into the fermenting media causes rapid inhibition of lactic acid bacteria metabolic activity. Malic acid concentrations were proportionally decreasing during 6 days of experiment and at the end the content of this acid varied between 0.16 and 0.22 g/L, the only exception formed a variant with the addition of SO2 (1.57 g/L of malic acid. After calculation of the average consumption rate of malic acid, the results showed the inhibition power – SO2 (81.05% followed by variant of 40 mg/L mixture of HFA (40.76%, a variant of 200 mg/L of DMDC (31.98% and a variant of 20 mg/L mixture of HFA (12.59%. The addition of HFA can significantly reduce the dosage of other preservatives, especially SO2. Based on results, this method can be recommend in the production of wines with residual sugar and also wines made from over-mature material to prevent undesirable MLF.

CLINSULF sub-dew-point process for sulphur recovery

Energy Technology Data Exchange (ETDEWEB)

Heisel, M.; Marold, F.

1988-01-01

In a 2-reactor system, the CLINSULF process allows very high sulphur recovery rates. When operated at 100/sup 0/C at the outlet, i.e. below the sulphur solidification point, a sulphur recovery rate of more than 99.2% was achieved in a 2-reactor series. Assuming a 70% sulphur recovery in an upstream Claus furnace plus sulphur condenser, an overall sulphur recovery of more than 99.8% results for the 2-reactor system. This is approximately 2% higher than in conventional Claus plus SDP units, which mostly consist of 4 reactors or more. This means the the CLINSULF SSP process promises to be an improvement both in respect of efficiency and low investment cost.

Design and modeling of an advanced marine machinery system including waste heat recovery and removal of sulphur oxides

DEFF Research Database (Denmark)

Frimann Nielsen, Rasmus; Haglind, Fredrik; Larsen, Ulrik

2013-01-01

-stroke diesel engine and a conventional waste heat recovery system. The results suggest that an organic Rankine cycle placed after the conventional waste heat recovery system is able to extract the sulphuric acid from the exhaust gas, while at the same time increase power generation from waste heat by 32...... consists of a two-stroke diesel engine, the wet sulphuric process for sulphur removal and an advanced waste heat recovery system including a conventional steam Rankine cycle and an organic Rankine cycle. The results are compared with those of a state-of-the-art machinery system featuring a two...

Sulphur removal in IGCC projects

Energy Technology Data Exchange (ETDEWEB)

Cross, F. (Parsons (United Kingdom))

1998-01-01

The technology for recovering elemental sulphur from H[sub 2]S bearing gases is well established. The modified Claus Process is the principal work-horse in sulphur recovery and can customarily achieve conversion efficiencies of 95% or better. Nowadays, such a level of recovery is no longer sufficient in most instances and sulphur recovery facility must then include some form of enhanced recovery, usually by treating the Claus tail gas. A number of processes have been introduced to enable the overall recovery to be increased. Recoveries in excess of 99% are both feasible and economic. Use of oxygen in place has become very popular in cases where oxygen is available cheaply or where capacity increases are designed. Most IGCC projects needing an air separation plant would automatically benefit from extending the use of oxygen to the sulphur recovery plant. The most popular route to minimising sulphur emissions in the context of IGCC projects has involved an oxygen based Claus plant followed by tail gas hydrogenation, hydrogen sulphide recovery and its recycle to the Claus section. The recovery of H[sub 2]S from the Claus tail gas can be integrated with the main gas treating system in the gasification plant. The cost advantage of doing so is significant. Parsons has been involved with the technology since 1949 and has been responsible for developments such as the ammonia burning Claus and jointly with Unocal, the BSRP tail gas process and Selectox processes. Recent innovations in response changing environmental and production requirements have included catalytic and tail gas processes which reduce sulphur emissions. 6 figs., 2 tabs.

Sulphur removal in IGCC projects

Energy Technology Data Exchange (ETDEWEB)

Cross, F. [Parsons (United Kingdom)

1998-12-31

The technology for recovering elemental sulphur from H{sub 2}S bearing gases is well established. The modified Claus Process is the principal work-horse in sulphur recovery and can customarily achieve conversion efficiencies of 95% or better. Nowadays, such a level of recovery is no longer sufficient in most instances and sulphur recovery facility must then include some form of enhanced recovery, usually by treating the Claus tail gas. A number of processes have been introduced to enable the overall recovery to be increased. Recoveries in excess of 99% are both feasible and economic. Use of oxygen in place has become very popular in cases where oxygen is available cheaply or where capacity increases are designed. Most IGCC projects needing an air separation plant would automatically benefit from extending the use of oxygen to the sulphur recovery plant. The most popular route to minimising sulphur emissions in the context of IGCC projects has involved an oxygen based Claus plant followed by tail gas hydrogenation, hydrogen sulphide recovery and its recycle to the Claus section. The recovery of H{sub 2}S from the Claus tail gas can be integrated with the main gas treating system in the gasification plant. The cost advantage of doing so is significant. Parsons has been involved with the technology since 1949 and has been responsible for developments such as the ammonia burning Claus and jointly with Unocal, the BSRP tail gas process and Selectox processes. Recent innovations in response changing environmental and production requirements have included catalytic and tail gas processes which reduce sulphur emissions. 6 figs., 2 tabs.

Acid hydrolysis of kallar grass (leptochloa fusca) for the production

International Nuclear Information System (INIS)

Chughtai, F.A.; Shah, M.H.

1993-01-01

Acid hydrolysis of kallar grass (leptochloa fusca) was carried of with various concentrations of sulphuric acid, ortho phosphoric acid and hydrochloric acid to produce furfural. The study revealed that activity of various hydrolysing acids to produce furfural from kallar grass was of the following order H/sub 2/SO/sub 4/ > H/sub 3/PO/sub 4/ > HCl. Optimum yield (4.78%) of the produce was obtained when the material was digested with 19% H/sub 2/SO/sub 4/ for a period of 20 minutes. (author)

Assessment of pollution due to oxides of sulphur and nitrogen at Tarapur

International Nuclear Information System (INIS)

Sudheendran, V.; Pimple, K.G.; Rao, D.D.; Chandramouli, S.; Iyer, R.S.; Hegde, A.G.

1995-01-01

An Environmental Survey Laboratory (ESL) was established in 1964 to monitor and assess the dispersion of radioactive releases from the power station in the environmental matrices. ESL has been making measurements of ambient sulphur dioxide concentration in the atmosphere at a few selected locations since 1984. The residential areas which are in the vicinity of the chemical zone experience acute effects of sulphur dioxide pollution from time to time depending upon the seasonal variations of meteorological parameters. The proposed commissioning of a thermal power station in the region (Dahanu) gives added importance to the estimation of SO 2 and NO 2 concentrations in the atmosphere. The paper presents data and assessment of the prevailing status with respect to above pollutants close to the industrial zone. (author). 5 refs., 3 tabs., 2 figs

Simultaneous analyses of gaseous and particulate sulphur compounds in the atmosphere by x-ray fluorescence spectrometry, (1)

International Nuclear Information System (INIS)

Matsuda, Yatsuka; Mamuro, Tetsuo

1974-01-01

An analytical technique for the simultaneous measurements of the atmospheric concentrations of SO 2 gas and sulphur absorbed by aerosol particles has been developed. Aerosol particles are collected on membrane filter and at the same time SO 2 gas is captured on alkali impregnated filter. The sulphur content in each filter is measured by an energy dispersive X-ray fluorescence spectrometer consisting of a Si(Li) semiconductor detector connected to a multichannel pulse hight analyzer and an excitation source of 55 Fe. Two methods are acceptable for the determination of the sulphur content in impregnated filter by X-ray fluorescence analysis. In the first method X-ray fluorescence analysis is made after the collected sulphur has diffused and distributed uniformly enough throughout filter, and in the second method X-ray fluorescence analysis has to be finished before the diffusion of the collected sulphur becomes appreciable. (auth.)

Impact of pedospheric and atmospheric sulphur nutrition on sulphur metabolism of Allium cepa L., a species with a potential sink capacity for secondary sulphur compounds

NARCIS (Netherlands)

Durenkamp, M.; De Kok, L.J.

Onion (Afflum cepa L.) was able to use atmospheric H2S as sole sulphur source for growth. The foliarly absorbed H2S was rapidly metabolized into water-soluble, non-protein thiol compounds, including cysteine, and subsequently into other sulphur compounds in the shoots. In H2S-exposed plants, the

Reprint of “Experiences in sulphur capture in a 30 MWth Circulating Fluidized Bed boiler under oxy-combustion conditions”

International Nuclear Information System (INIS)

Gómez, M.; Fernández, A.; Llavona, I.; Kuivalainen, R.

2015-01-01

CO 2 and SO 2 from fossil fuel combustion are contributors to greenhouse effect and acid rain respectively. Oxy-combustion technology produces a highly concentrated CO 2 stream almost ready for capture. Circulating Fluidized Bed (CFB) boiler technology allows in-situ injection of calcium-based sorbents for efficient SO 2 capture. CIUDEN's 30 MWth CFB boiler, supplied by Foster Wheeler and located at the Technology Development Centre for CO 2 Capture and Transport (es.CO 2 ) in Spain, is the first of its kind for executing test runs at large pilot scale under both air-combustion and oxy-combustion conditions. In this work, SO 2 emissions under different scenarios have been evaluated. Variables such as limestone composition, Ca/S molar ratio and bed temperature among others have been considered along different test runs in both air-combustion and oxy-combustion conditions to analyse its influence on SO 2 abatement. Fly and bottom ash, together with flue gas analysis have been carried-out. Desulphurization performance tests results are presented. - Highlights: • Sulphur capture efficiency (%) was higher in oxy-combustion compared to air-combustion in a 30 MW thermal CFB boiler using anthracite and limestone as sulphur sorbent. • For a Ca/S molar ratio higher than 2.6 there was barely any improvement on sulphur capture efficiency for both air-combustion and oxy-combustion conditions in a 30 MW thermal CFB boiler using anthracite and limestone as sulphur sorbent. • Optimum temperature for sulphur capture at a fixed Ca/S molar ratio is around 880–890 °C under oxy-combustion conditions and for anthracite coal with limestone as sorbent in a 30 MW thermal CFB boiler

Harties' two-man acid plant now fully on stream

International Nuclear Information System (INIS)

Anon.

1979-01-01

Hartebeesfontein gold mine is the most modern of its kind in South Africa. Only two men are required to operate this R12 million acid plant. The plant is capable of producing 140 000 t of sulphuric acid a year, and will meet its own uranium recovery process requirements as well as those of other uranium producers in the Klerksdorp and Stilfontein areas. In simplified form the process involves roasting pyrite to form sulphur dioxide. This is then cleaned, dried, heated and reacted over catalyst to produce sulphur tri-oxide which is combined with water to form sulphuric acid. Where the pyrite is gold-bearing, the resultant calcines from the roasting process are pumped to the mine's recovery plant where the residual gold is extracted. The main reason for the construction of the plant was to supply Hartebeesfontein and other uranium producers in the Klerksdorp and Stilfontein areas with sulphuric acid which is used in the uranium leaching process

Sulphur oxidising bacteria in mangrove ecosystem: A review ...

African Journals Online (AJOL)

Sulphur-oxidizing bacteria such as photoautotrophs, chemolithotrophs and heterotrophs play an important role in the mangrove environment for the oxidation of the toxic sulphide produced by sulphur reducing bacteria and act as a key driving force behind all sulphur transformations in the mangrove ecosystem which is ...

Sulphur-containing compounds in sulphur-rich crude oils from hypersaline lake sediments and their geochemical implications

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Guoying, S.; Jiamo, F.; Brassell, S.C.; Gowar, A.P.; Eglinton, G.; Leeuw, J.W. de; Schenck, P.A.

1987-01-01

Three sulphur-rich commercial crude oils have been studied, which contain sulphur as high as up to 4 —12 %. These samples were collected from Tertiary hypersaline lake sediments of the Jianghan Basin, Hubei Province at different depths, but above the oil generation threshold (2200m). FPD-GC and

Feasibility study of various sulphonation methods for transforming carbon nanotubes into catalysts for the esterification of palm fatty acid distillate

International Nuclear Information System (INIS)

Shuit, Siew Hoong; Tan, Soon Huat

2014-01-01

Highlights: • First report on the production of biodiesel from low-value industrial by-product using sulphonated MWCNTs as catalyst. • Various sulphonation methods were used to transform MWCNTs into catalysts. • SO 3 H were successfully grafted on the surface of MWCNTs, which resulted in a high biodiesel yield and reuse capacity. • The maximum FAME yield by sulphonated MWCNTs was higher than for other popular solid acid catalysts. - Abstract: Sulphonated multi-walled carbon nanotubes were synthesised and utilised as catalysts to transform palm fatty acid distillate, the low-value by-product of palm oil refineries, into the more valuable product of biodiesel. The most common method to prepare carbon-based solid acid catalysts is thermal treatment with concentrated sulphuric acid, which is a time-consuming and energy-intensive process. Therefore, the feasibility of other sulphonation methods, such as the in situ polymerisation of acetic anhydride and sulphuric acid, the thermal decomposition of ammonium sulphate and the in situ polymerisation of poly(sodium4-styrenesulphonate), were examined in this study. The esterification reaction was performed at 170 °C for 3 h at a methanol to palm fatty acid distillate ratio of 20 and catalyst loading of 2 wt% in a pressurised reactor. The fatty acid methyl esters yields achieved by the sulphonated multi-walled carbon nanotubes prepared via thermal treatment with concentrated sulphuric acid, the in situ polymerisation of acetic anhydride and sulphuric acid, the thermal decomposition of ammonium sulphate and the in situ polymerisation of poly(sodium4-styrenesulphonate) were 78.1%, 85.8%, 88.0% and 93.4%, respectively. All catalysts could maintain a high catalytic activity even during the fifth cycle. Among the sulphonation methods, the in situ polymerisation of poly(sodium4-styrenesulphonate) produced the catalyst with the highest acid group density. In addition, the resonance structures of the benzenesulphonic acid

The useful application of sulphur-bound waste materials

NARCIS (Netherlands)

Alkemade, M.M.C.; Koene, J.I.A.

1996-01-01

An immobilization process is described which is based on sulphur (instead of cement) as a binding agent for the treatment of hazardous waste materials. Elemental sulphur is able to bind chemically metals such as mercury and, to a lesser extent, lead as metal sulphides. Furthermore, sulphur forms a

Utilization of activated carbon loaded with sulphur for sulphur fertilization in agriculture; Verwertung von mit Schwefel beladener Aktivkohle als Schwefelduenger in der Landwirtschaft

Energy Technology Data Exchange (ETDEWEB)

Kirfel, Kristina; Hoffmann, Heide [Humboldt Univ. Berlin (Germany). AG Agraroekologie und Oekologischer Landbau

2013-01-15

Due to the decrease of atmospheric sulphur deposition, sulphur fertilization has gained significance for agriculture in recent years. Carbon-sulphur-pellets (CSP), activated carbon pellets loaded with sulphur, previously used for desulphurization in biogas plants, are up to now disposed of as waste. In this context the question arises if CSP could be of use for sulphur fertilization of agricultural crops. The objective of this study was to test sulphur release and plant availability from, and plant tolerance towards CSP. A pot experiment using Zea mays with different shares of CSP was carried out. Leaf green intensity of vital plants, indicating plants' current nutritional status, was measured and differences in plant development were documented regularly. At the end of the trial period biomass and elemental contents of the test plants, as well as electrical conductivity and pH-value of the substrate-CSP-mixtures were determined. Amendments of 0.2 m.-% to 1.0 m.-% had a positive effect on plants' dry mass yield; higher shares led to considerable yield losses. By addition of CSP, sulphur content in the plant dry mass increased compared to the control without sulphur fertilization. This result indicates that sulphur adsorbed to activated carbon becomes plant available when applicated to cultural substrate. (orig.)

Environmental aspects of sulphuric acid in situ leach uranium mining in the permafrost zone (Vitim District, Russian Federation)

International Nuclear Information System (INIS)

Fazlullin, M.I.; Boitsov, A.V.

2002-01-01

Currently in situ leaching pilot tests are in progress at the Khiagda deposit, Vitim District, Russian Federation. The deposit is of the sandstone basal channel type, or paleovalley type in the Russian classification. It contains about 15 000 mt U at an ore grade averaging 0.05% U. Mineralization occurs in permeable unconsolidated Neogene fluvial sediments located below the permafrost which extends to 100 m deep. The basement rock is Paleozoic granite. Neogene-Quaternary basalts overlap the ore hosting sediments. The thickness of the ore host horizon varies from a few meters to 120 m. The depth of mineralization averages 170 m. Ore bodies are of lens and strataform shape. The following types of underground waters have been identified: groundwaters of the near surface or active layer, the aquifer in the Neogene volcanics, the ore host aquifer of the Neogene permeable sediments and fault related waters. The permeability in the ore bearing horizon varies from 0.1 to 20 m/day (averages 2 to 3 m/day). The waters of the productive aquifer are not suitable for industrial nor potable water supply due to their initial chemical composition. The ore host horizons occur between two impermeable horizons, which confine leaching solutions. Using sulphuric acid solutions as leaching reagent decreases the pH and increases Total Dissolved Solids (TDS) of the groundwaters within the leaching area due to concentration of sulphate-ion and other dissolved components. Principal components contaminating the underground waters are sulphates of aluminium, manganese, nickel and chrome. Their content during leaching significantly exceeds initial values. The available information on residual acid migration with the ground water shows that the concentration of contaminants significantly decreases away from the leaching contour. This occurs due to precipitation of contaminants during migration of the underground water from ISL sites. The external contour of the contamination aureole is defined

Isolation and fractionation of soil humin using alkaline urea and dimethylsulphoxide plus sulphuric acid

Science.gov (United States)

Song, Guixue; Hayes, Michael H. B.; Novotny, Etelvino H.; Simpson, Andre J.

2011-01-01

Humin, the most recalcitrant and abundant organic fraction of soils and of sediments, is a significant contributor to the stable carbon pool in soils and is important for the global carbon budget. It has significant resistance to transformations by microorganisms. Based on the classical operational definition, humin can include any humic-type substance that is not soluble in water at any pH. We demonstrate in this study how sequential exhaustive extractions with 0.1 M sodium hydroxide (NaOH) + 6 M urea, followed by dimethylsulphoxide (DMSO) + 6% ( v/ v) sulphuric acid (H2SO4) solvent systems, can extract 70-80% of the residual materials remaining after prior exhaustive extractions in neutral and aqueous basic media. Solid-state 13C NMR spectra have shown that the components isolated in the base + urea system were compositionally similar to the humic and fulvic acid fractions isolated at pH 12.6 in the aqueous media. The NMR spectra indicated that the major components isolated in the DMSO + H2SO4 medium had aliphatic hydrocarbon associated with carboxyl functionalities and with lesser amounts of carbohydrate and peptide and minor amounts of lignin-derived components. The major components will have significant contributions from long-chain fatty acids, waxes, to cuticular materials. The isolates in the DMSO + H2SO4 medium were compositionally similar to the organic components that resisted solvation and remained associated with the soil clays. It is concluded that the base + urea system released humic and fulvic acids held by hydrogen bonding or by entrapment within the humin matrix. The recalcitrant humin materials extracted in DMSO + H2SO4 are largely biological molecules (from plants and the soil microbial population) that are likely to be protected from degradation by their hydrophobic moieties and by sorption on the soil clays. Thus, the major components of humin do not satisfy the classical definitions for humic substances which emphasise that these arise from

Determination of sulphur-35 impurity in solutions of phosphorus-32

International Nuclear Information System (INIS)

Rodriguez Pasques, R.H.; Iglicki, F.A; Cittadini, P.E.

1982-01-01

A method has been developed in order to evaluate the activity of sulphur-35 impurity in solutions of phosphorus-32. The procedure is based on the precipitation on benzidine sulphate in acid solution and further purification by dissolving and reprecipitating under appropriate conditions. 35 S beta radiation is measured with and end-window gas counter. A correction for any remaining 32 P is determined by differential absorption through aluminum. (author) [es

Preparation and characterization compatible pellets for immobilization of colloidal sulphur nanoparticles

Science.gov (United States)

Adlim, M.; Zarlaida, F.; Khaldun, I.; Dewi, R.; Jamilah, M.

2018-03-01

Mercury pollution in atmosphere is dominated by mercury vapour release from coal burning and gold-amalgam separation in gold mining. The initial steps in formulating a compatible mercury absorbent for mercury stabilization was fabrication of pellet supported colloidal sulphur. Sulphur is used to stabilize mercury vapour by formation of metacinnabar that has much lower toxicity. The sulphur reactivity toward mercury vapour can be enhanced by using colloidal sulphur nanoparticles immobilized on compatible pellets. Clay pellets would have heat resistance but in fact, they were less stable in aqueous solution although their stability increased with inclusion of rice husk ash and sawdust or pineapple leaf fibre in the composite. Pellets made of rice husk ash and polyvinyl acetate were stable in water at least for 24 hours. Sulphur from thiosulfate precursor that immobilized onto surface of pellet using chitosan as the stabilizer and the binding agent gave lower sulphur content compared to sulphur from other precursors (sulphur powder and sulphur-CS2). Sulphur from thiosulfate precursor was in form of colloid, has nanosize, and disperse particles on the surface of rice husk ash pellets. Sulphur immobilization methods affect on sulphur particles exposure on the pellet surface.

Nuclear physical express analysis of solid fuel sulphur content

International Nuclear Information System (INIS)

Pak, Yu.; Ponomaryova, M

2005-01-01

Full text: Sulphur content is an important qualitative coal parameter. The problem of coal sulphur content determining remains one of the most important both in Kazakhstan and in other coal-mining countries. The traditional method of sampling, the final stage of which is chemical analysis of coal for sulphur, is characterized by high labour intensity and low productivity. That's why it is ineffective for mass express analytical quality control and technological schemes of coal processing control. In this connection it is very urgent to develop a method of coal sulphur content on the base of a series nuclear-geophysical equipment with an isotope source of primary radiation, allowing to increase analysis representativity and maximally take into account coal real composition inconstancy. To solve the problem set it is necessary to study the main laws of X-ray-radiometric method applied to the coal quality analysis for working out instrumental methods of speed determining of coal sulphur content with satisfactory accuracy for technological tasks, to determine laws of changing the flows of characteristic X-ray and scattered radiation from coal sulphur content of various real composition and to optimize methodical and hardware parameters, providing minimal error of sulphur content control. On the base of studying laws of real composition coal components and their interconnections with sulphur content there has been substantiated the expediency of using hardware functions of calcium and iron to control coal sulphur contents; there has been suggested a model to estimate the methodical error of coal sulphur content determining on the base of the data about sensitivity to sulphur and effecting factors using ultimate methods of coal components substitution methods allowing to optimize sulphur control parameters; there has been worked out an algorithm of X-ray-radiometric control of sulphur content based on the sequential radiating the analyzed coal with gamma-radiation of

Sulphur isotope variations in the atmosphere

International Nuclear Information System (INIS)

Newman, L.; Krouse, H.R.; Grinenko, V.A.

1991-01-01

The measurement of the isotope ratios of sulphur and oxygen can in principal be used to assess sulphur inputs into, transformation within, and removal from the atmosphere. Major inputs arise from both anthropogenic and biogenic activities. Transformations arise from oxidation, neutralization, and other chemical reactions. Advection causes dilution and the main removal processes are dry deposition (governed by gravitation and diffusion) and rain. The admixture of sources can be discerned from their isotopic signatures whereas transformations and removal can be followed from the isotopic fractionation that might occur. In this chapter, the atmospheric sulphur cycle and the associated chemistry are summarized. Also presented is information on natural isotopic variations and fundamental concepts relating to the use of isotopic data to delineate anthropogenic S in the atmosphere. Examples of successful applications of these concepts are given. Finally, consideration is given to the potential of using isotopically enriched sulphur to study transport and transformation of atmospheric S compounds. Refs, figs and tabs

The recovery of sulphur, uranium and gold from residues in OFS scheme

International Nuclear Information System (INIS)

Ruhmer, W.T.; Botha, F.; Adams, J.S.

1978-01-01

This article describes a project comprising three plants for the flotation of pyrite, a twin-stream uranium plant in which high-grade slimes and pyrite can be leached separately, a pyrite burning sulphuric acid plant, and a plant for the recovery of gold from calcines. Details of these plants including capital costs and estimate production are given

Impurity photovoltaic effect in silicon solar cell doped with sulphur: A numerical simulation

International Nuclear Information System (INIS)

Azzouzi, Ghania; Chegaar, Mohamed

2011-01-01

The impurity photovoltaic effect (IPV) has mostly been studied in various semiconductors such as silicon, silicon carbide and GaAs in order to increase infrared absorption and hence cell efficiency. In this work, sulphur is used as the IPV effect impurity incorporated in silicon solar cells. For our simulation we use the numerical device simulator (SCAPS). We calculate the solar cell performances (short circuit current density J sc , open circuit voltage V oc , conversion efficiency η and quantum efficiency QE). We study the influence of light trapping and certain impurity parameters like impurity concentration and position in the gap on the solar cell performances. Simulation results for IPV effect on silicon doped with sulphur show an improvement of the short circuit current and the efficiency for sulphur energy levels located far from the middle of the band gap especially at E c -E t =0.18 eV.

Biodesulphurisation of high sulphur coal by heap leaching

Energy Technology Data Exchange (ETDEWEB)

J. Cara; M.T. Carballo; A. Moran; D. Bonilla; O. Escolano; F.J. Garcia Frutos [Universidad de Leon, Leon (Spain). Departamento de Ingenieria Quimica

2005-10-01

The biodesulphurisation of coal carried out in pile could be an interesting option to clean coal. In view of the good results obtained in biodesulphurisation test column at lab scale on a sample of semianthracite coal that proceed of an industrial plant with a high sulphur content, mainly pyritic sulphur, the feasibility of the process at pilot plant scale was studied. The pile was formed with 6 ton of gravity middlings coal sample with a grain size -12+0.5 mm from S.A. Hullera Vasco-Leonesa industrial plant. The coal has a total sulphur content of 3.78% and a pyritic sulphur content of 2.88%, the rest of sulphur is organic sulphur. The biodesulphurisation process in pilot plant follows three stages: stabilization of the pile, biodesulphurisation and washing. Heap was sampled twice during stabilisation stage, at the end of desulphurisation process and finally once washed. A pyritic sulphur removal of 39% and total sulphur removal of 23% was obtained. To complete the bioleaching process, the treatment of purge of leachate was carried out with the objective to recycling to head of process. The best treatment was a pre-treatment of the leachate until pH 4, and further treatment by reverse osmosis of the clarified water. Comparing this process with conventional precipitation to reach disposal limits, the reagents consumption and sludges were reduced considerably and due to the high quality of permeate it permits to recycle it to head of process. 18 refs., 6 figs., 6 tabs.

Extraction of niobium and tantalum with bis-2-ethylhexyl acetamide

International Nuclear Information System (INIS)

Ohmori, Hiroshi; Shibata, Junji; Sano, Makoto; Nishimura, Sanji

1986-01-01

Extraction of Nb and Ta from acid solutions with bis-2-ethylhexyl acetamide and stripping of these metals with sulphuric acid solutions were investigated. The organic phase was a binary solution of bis-2-ethylhexyl acetamide and xylene, while the aqueous phase was composed of hydrofluoric acid solution or hydrofluoric-sulphuric acid solution containing 3.5 - 13 kg/m 3 Nb and 5 - 10 kg/m 3 Ta. Sulphuric acid, hydrochloric acid and nitric acid were used as salting out agents to understand the effect on the extraction. Both metals were not sufficiently extracted from hydrofluoric acid solutions, whereas the extraction of both metals remarkably increased with an addition of sulphuric acid to the aqueous phase. The separation factor decreased with an increase in the concentration of hydrofluoric acid at the constant sulphuric acid concentration of 5.8N, and both metals were completely coextracted in the aqueous condition of 6N hydrofluoric acid and 8N sulphuric acid. The stripping occurred for both metals with a high efficiency, when water or dilute sulphuric acid solution was used as a stripping agent. The increase in sulphuric acid concentration caused less stripping of Ta, while the stripping of Nb was maintained at 80 % up to 7N sulphuric acid. The separation factor reached the maximum with the value of 116 in the use of 6.5N sulphuric acid. The extraction behavior of Fe(II), Fe(III), Sn(IV) and Mn(II) was also examined with the results that these metals were not extracted even to the extent of the lowest limit of atomic absorption spectrophotometer. Moreover, the comparison of this extractant with MIBK and TBP, which were in common use, was carried out. (author)

Sulphur mustard degradation on zirconium doped Ti-Fe oxides

Energy Technology Data Exchange (ETDEWEB)

Stengl, Vaclav, E-mail: stengl@iic.cas.cz [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i 250 68 Husinec-Rez (Czech Republic); Grygar, Tomas Matys [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i 250 68 Husinec-Rez (Czech Republic); Oplustil, Frantisek; Nemec, Tomas [Military Technical Institute of Protection Brno Veslarska 230, 628 00 Brno (Czech Republic)

2011-09-15

Highlights: {yields} New stechiometric materials for sulphur mustard degradation. {yields} High degree of degradation, more then 95% h{sup -1}. {yields} One-pot synthesis procedure. - Abstract: Zirconium doped mixed nanodispersive oxides of Ti and Fe were prepared by homogeneous hydrolysis of sulphate salts with urea in aqueous solutions. Synthesized nanodispersive metal oxide hydroxides were characterised as the Brunauer-Emmett-Teller (BET) surface area and Barrett-Joiner-Halenda porosity (BJH), X-ray diffraction (XRD), infrared (IR) spectroscopy, scanning electron microscopy (SEM) with energy-dispersive X-ray (EDX) microanalysis, and acid-base titration. These oxides were taken for an experimental evaluation of their reactivity with sulphur mustard (chemical warfare agent HD or bis(2-chloroethyl)sulphide). The presence of Zr{sup 4+} dopant tends to increase both the surface area and the surface hydroxylation of the resulting doped oxides in such a manner that it can contribute to enabling the substrate adsorption at the oxide surface and thus accelerate the rate of degradation of warfare agents. The addition of Zr{sup 4+} to the hydrolysis of ferric sulphate with urea shifts the reaction route and promotes formation of goethite at the expense of ferrihydrite. We discovered that Zr{sup 4+} doped oxo-hydroxides of Ti and Fe exhibit a higher degradation activity towards sulphur mustard than any other yet reported reactive sorbents. The reaction rate constant of the slower parallel reaction of the most efficient reactive sorbents is increased with the increasing amount of surface base sites.

Fermentative utilization of glycerol residue for the production of acetic acid

Science.gov (United States)

Irvan; Trisakti, B.; Hasibuan, R.; Joli, M.

2018-02-01

Glycerol residue, frequently known as pitch, is a waste produced from the downstream product of crude glycerine distillation. With the increasing need of pure glycerine in the world, the glycerol residue produced is also increasing. Glycerol residue is a solid waste at room temperature, highly alkaline (pH > 13), corrosive, and categorized as hazardous and poisonous waste. In this research, acetic acid was produced from glycerol residue through the anaerobic fermentation process by using purple non-sulphur photosynthetic bacteria. The purpose of this study was to find out the influence of concentration change of glycerol residue on time and to find out the possibility of glycerol residue to be utilized as acetic acid. In this research, at first 400 g of glycerol residue was diluted with 200 ml of distilled water to change the glycerine phase, from solid to liquid at room temperature, acidified by using hydrochloric acid until pH 2. The top layer formed was fatty acid and triglycerides that should be removed. Meanwhile, the bottom layer was diluted glycerol residue which was then neutralized with caustic soda. To produce acetic acid, glycerol residue with various concentrations, salt, and purple non-sulphur photosynthetic bacteria were put together into a 100 ml bottle which had been previously sterilized, then incubated for four weeks under the light of 40-watt bulb. The result showed that on the 28th day of fermentation, the produced acetic acid were 0.28, 1.85, and 0.2% (w/w) by using glycerine with the concentration of 0.5, 1.0, and 1.5% (w/w), respectively.

Potential to reduce emissions of sulphur dioxide through reducing sulphur levels in heavy and light fuel oils - a discussion paper

International Nuclear Information System (INIS)

Tushingham, M.; Bellamy, J.

2001-01-01

Background information on the sulphur levels in light fuel oil (used in residential heating) and heavy fuel oil (used as industrial fuel oil) is provided. In addition to the description of sulphur levels in light and heavy fuel oils, the report also provides a summary of regulatory limits in Canada and elsewhere, and a description of the emission benefits of decreasing sulphur in fuels. 4 refs., 10 tabs., 12 figs

Source of sulphur in the Ebro Basin (Northern Spain). Tertiary nonmarine evaporite deposits as evidenced by sulphur isotopes

International Nuclear Information System (INIS)

Birnbaum, S.J.; Coleman, D.

1979-01-01

The Ebro Basin is an intermontane basin, located in northern Spain, filled with Tertiary (largely Oligocene and Miocene) elastic and chemical deposits. Sulphur isotopes are utilized to determine the source of sulphur in the sulphate deposits (predominantly gypsum with accessory thenardite, mirabolite and epsomite). Data obtained from Tertiary gypsum rocks produce a range of delta 34 S values from +9.16% to + 14.02% with a mean of +13.61%. Data obtained from Triassic gypsum rocks (in source area) produce a range from +13.73% to +15.14%, with a mean of +14.66%. Values for Tertiary marine water range from +18% to +24%. These data indicate a nonmarine origin for sulpur within the Tertiary sulphate rocks. The contribution of Triassic sulphur to the groundwater system, plus varying degrees of dilution by isotopically lighter (atmospheric and sulphide) sulphur, best explains the isotopic ratios observed in the Tertiary Basin deposits. (Auth.)

The mechanism of photosystem-II inactivation during sulphur deprivation-induced H2 production in Chlamydomonas reinhardtii.

Science.gov (United States)

Nagy, Valéria; Vidal-Meireles, André; Podmaniczki, Anna; Szentmihályi, Klára; Rákhely, Gábor; Zsigmond, Laura; Kovács, László; Tóth, Szilvia Z

2018-05-01

Sulphur limitation may restrain cell growth and viability. In the green alga Chlamydomonas reinhardtii, sulphur limitation may induce H 2 production lasting for several days, which can be exploited as a renewable energy source. Sulphur limitation causes a large number of physiological changes, including the inactivation of photosystem II (PSII), leading to the establishment of hypoxia, essential for the increase in hydrogenase expression and activity. The inactivation of PSII has long been assumed to be caused by the sulphur-limited turnover of its reaction center protein PsbA. Here we reinvestigated this issue in detail and show that: (i) upon transferring Chlamydomonas cells to sulphur-free media, the cellular sulphur content decreases only by about 25%; (ii) as demonstrated by lincomycin treatments, PsbA has a significant turnover, and other photosynthetic subunits, namely RbcL and CP43, are degraded more rapidly than PsbA. On the other hand, sulphur limitation imposes oxidative stress early on, most probably involving the formation of singlet oxygen in PSII, which leads to an increase in the expression of GDP-L-galactose phosphorylase, playing an essential role in ascorbate biosynthesis. When accumulated to the millimolar concentration range, ascorbate may inactivate the oxygen-evolving complex and provide electrons to PSII, albeit at a low rate. In the absence of a functional donor side and sufficient electron transport, PSII reaction centers are inactivated and degraded. We therefore demonstrate that the inactivation of PSII is a complex and multistep process, which may serve to mitigate the damaging effects of sulphur limitation. © 2018 The Authors The Plant Journal © 2018 John Wiley & Sons Ltd.

Corrosion Inhibition of Aluminium in Acid Media By Citrullus Colocynthis Extract

Directory of Open Access Journals (Sweden)

Rajkiran Chauhan

2011-01-01

Full Text Available Inhibition of corrosion of aluminium in acid solution by methanol extract of Citrullus colocynthis plant has been studied using mass loss and thermometric measurements. It has been found that the plant extract act as a good corrosion inhibitor for aluminium in all concentrations of sulphuric and hydrochloric acid solution. The inhibition action depends on the concentration of acid and inhibitor. Results for mass loss and thermometric measurement indicate that inhibition efficiency increase with increasing inhibitor concentration. The inhibition action of the plant extract is discussed in view of Langmuir adsorption isotherm. It has been observed that the adsorption of the extract on aluminium surface is a spontaneous process. The plant extract provides a good protection to aluminium against corrosion.

A new approach for the determination of sulphur in food samples by high-resolution continuum source flame atomic absorption spectrometer.

Science.gov (United States)

Ozbek, N; Baysal, A

2015-02-01

The new approach for the determination of sulphur in foods was developed, and the sulphur concentrations of various fresh and dried food samples determined using a high-resolution continuum source flame atomic absorption spectrometer with an air/acetylene flame. The proposed method was optimised and the validated using standard reference materials, and certified values were found to be within the 95% confidence interval. The sulphur content of foods ranged from less than the LOD to 1.5mgg(-1). The method is accurate, fast, simple and sensitive. Copyright © 2014 Elsevier Ltd. All rights reserved.

How sulphur was dislodged to sustain plant operation

International Nuclear Information System (INIS)

Verma, A.N.; Agarwal, A.K.

1997-01-01

Heavy Water Plant (Kota) employs chemical exchange between water and hydrogen sulphide gas. Formation of sulphur is a known phenomena during production of heavy water in G.S. process plants. It is observed that after three years of plant operation this sulphur is enough to choke the cold tower trays causing flooding of exchange towers and resultant decrease in throughput. G.S. process plants normally go for major turn around once in four years when sulphur is either manually cleaned or removed by steam wash after hydrogen sulphide gas has been removed from the system and towers have been fully decontaminated. As throughput starts decreasing after third year and plant operation becomes more difficult in fourth year, HWP (Kota) had evolved a procedure of heating the towers for dislodging sulphur from sieve trays when plant is running. With these procedures plant operation could be sustained without tower floodings even in fourth year, before plant could go for major turn around for manual removal of sulphur

Analytical procedure for the titrimetric determination of uranium in concentrates

International Nuclear Information System (INIS)

Florence, T.M.; Pakalns, P.

1989-01-01

In 1964 Davis and gray published a titrimetric method for uranium which does not require column reductors, electronic instruments or inert atmospheres, and is sufficiently selective to enable uranium to be determined without prior separation. The method involves reduction of uranium (VI) to (IV) by ferrous sulphate in concentrated phosphoric acid medium. The excess ion (II) is then selectively oxidised by nitric acid using molybdenum catalyst. After addition of sulphuric acid and dilution with water, the uranium (IV) is titrated with standard potassium dichromate, using barium diphenylamine sulphonate indicator. This method has been found to be simple, precise and reliable, and applicable to a wide range of uranium-containing materials. The method given here for determining uranium in concentrates is essentially that of Davies and Gray. Its applications, apparatus, reagents, procedures and accuracy and precision are discussed. 10 refs

Transport and concentration of abscisic acid (ABA) and auxin (IAA) in deciduous and coniferous trees. Transport und Gehalt von Abscisinsaeure (ABA) und Auxin (IAA) in Laub- und Nadelblaettern

Energy Technology Data Exchange (ETDEWEB)

Hartung, W.

1988-09-01

Abscisic acid and indoleacetic acid were chosen to examine whether intact deciduous and coniferous tissues from spruce, hemlock fir, spinage, barley and sorrel or isolated mesophyll protoplasts from barley and closing cell preparations from Valerianella locusta are affected by sulphur dioxide in terms of changes in the concentration, transportation and distribution of such plant hormones. The distribution of phytohormones like ABA and IAA over the individual cell compartments is determined by the different pH gradients of the latter. Owing to their acidity these hormones are accumulated in alkaline cell inclusion bodies like chloroplasts and cytosol. Potentially acid air pollutants like SO{sub 2} and NO{sub x} lead to acidification of previously alkaline cell compartments, due to which fact the cellular pH gradients are reduced. This, in turn, gives rise to a redistribution of phytohormones to the effect that certain target cells such as closing cells of leaves or meristem cells come under the influence of altered hormone concentrations and compositions. This is bound to affect the processes controlling the development, growth and stress behaviour of plants. (orig.) With 55 refs., 2 tabs., 16 figs.

Physico-chemical conversion of sulphur dioxide in a power plant plume

International Nuclear Information System (INIS)

Lewin, E.E.

1978-03-01

A review is given of the actual knowledge of SO 2 atmospheric processes gained from laboratory and field experiments. Implementation is described of the instrumentation, operational procedures and analytical methods in connection with a field study of the conversion and dispersion of SO 2 in an oil-fired power plant plume. Furthermore, the preliminary results are included of five experiments performed until the end of 1976. Measurements were performed from an aircraft and included continuous registration of NOsub(x), SO 2 , SF 6 , and particle concentrations, as well as temperature and humidity. It was planned to label sulphur from the source in question with sulphur-35. However, this part of the experiment had to be abandoned because of public opinion on the use of radioactive tracers. Sulphur hexafluoride was used as an internal tracer for the plume. A half-life for SO 2 of about 30 min was determined from one of the experiments. In this connection the possibility of using NOsub(x) as a conservative tracer is shown. Possible ways of removal are discussed and the rate of two of the processes is calculated by means of a model describing the chemical conversion in a dispersing plume. (author)

Organic sulphur in macromolecular sedimentary organic matter. II. Analysis of distributions of sulphur-containing pyrolysis products using multivariate techniques

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Eglinton, T.I.; Pool, W.; Leeuw, J.W. de; Eijkel, G.; Boon, J.J.

1992-01-01

This study describes the analysis of sulphur-containing products from Curie-point pyrolysis (Py) of eighty-five samples (kerogens, bitumen, and petroleum asphaltenes and coals) using gas chromatography (GC) in combination with sulphur-selective detection. Peak areas of approximately forty individual

Relationship between sulphate and sulphur dioxide in the air

Energy Technology Data Exchange (ETDEWEB)

Fugas, M; Gentilizza, M

1978-01-01

The relationship between the sulphate in suspended particulates and sulphur dioxide in the air was studied in various urban and industrial areas. The relationship is best described by the equation y = ax/sup b/, where y is the percentage of the sulphate S in the total S (sulphate and sulphur dioxide) and x is the concentration of the total S in the air. The regression coefficients a and b seem to be characteristics of the area. In urban areas studied so far a was between 316 and 378 and b between -0.74 and -0.83. In industrial areas polluted by dust which contains elevated concentrations of metals a was between 91 and 107 and b between -0.35 and -0.49. In the area polluted by cement dust there was practically no correlation between the sulphate S (%) and the total S, but a relatively high correlation between absolute amounts of the sulphate S and the total S. The relations indicate that the limitation of SO/sub 2/ conversion is influenced by aerosol composition. Aerosols containing certain metals may promote the conversion by a catalytic effect while alkaline substances by increasing the pH. Whether this can only happen in the plume or in the air as well remains to be clarified.

Effect of Simulated Acid Rain on the Germination, Growth, Elements, Protein and Photosynthetic Pigments Contents in Tomato (Lycopersicon esculentum

Directory of Open Access Journals (Sweden)

M. Askary

2014-04-01

Full Text Available Uncontrolled use of fossil fuels in industries and the transport sector has led to an increase in concentrations of gaseous pollutants such as sulphur dioxide (SO2, nitrogen dioxide (NO2 and their derivatives and ozone (O3. In addition to dry and wet deposition of these gases has been the major route of influx in ionic form into the ecosystem. This investigation was evaluated the effects of simulated acid rain (SAR with different pH (6.8 as control, 6.5, 6, 5.5, 5, 4.5, 4, 3.5, 3 and 2.5 on germination, growth, elements, protein, photosynthetic pigments contents of Lycopersicon esculentum in hydroponic culture. Experiments were conducted at research laboratory of arak university in summer of 1391. Results were showed that from pH=6.8 until pH=5/5 significantly increased P and K and protein content, root and shoot dry and wet weight. SAR exposure with high acidity (pH=5/5 until pH=2.5 significantly suppressed germination, growth index, measured elements as P and K, protein and photosynthetic pigments, while significant increased sulphur contect from 150% to 550% compared to controls. Maximal amounts sulphur were measured in pH=2/5. Acid rain in low pH were decrease plant growth and make protein and incearsed sulphur content in leaf. As regards, low acidity promoted the growth of tomato plants and high acidity inhibit, Therefore, it is recommended that tomato plants cultures in soils with low acidity.

Influence of sulphur addition on emissions of organic substances during combustion; Inverkan av formen av svaveladditiv paa emissionerna av kolmonoxid och organiska aemnen vid foerbraenning

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik; Jonsson, Claes; Almark, Matts; Berg, Magnus; Streibel, Thorsten; Zimmermann, Ralf

2008-02-15

Reduction of emissions of carbon monoxide and organic substances by injecting either ammonium sulphate or elemental sulphur and the importance of the point of injection has been investigated in full scale in a grate-fired bark boiler. The effect was monitored downstream of the economizer and air preheater, immediately upstream of the electrostatic precipitator. Concentrations determined in the comprehensive monitoring program include principally carbon monoxide, TOC and several organic substances, including PAH, PCDD/F and polychlorinated benzenes (PCBz). Additionally, the gaseous PAH were determined on-line using a novel mass spectrometer, REMPI-TOF MS, that measures specifically the 2- to 4-ring PAH's. All concentrations of substances of interest here fluctuate in concert and peak simultaneously. The relationship between the concentrations is not straightforward: there appears to be a threshold in carbon monoxide concentration. Below this threshold, the concentration of organics is low and above it concentrations increase rapidly with increasing carbon monoxide concentration. It has been confirmed that using sulphur additives not only reduces the concentration of carbon monoxide, but also that of organic substances in the flue gases. These additives do not only reduce the mean level of concentrations, but also dampen the fluctuations in these concentrations. Any measure leading to a reduction in carbon monoxide will also decrease the concentration of most organics, under the conditions prevalent in this boiler. Both additives tested are equally effective per kg of pure sulphur. The point of injection, in the fuel or above the grate, is not important. The PCDD/F concentration in the flue gases is very low even without additives, and the effect of sulphur on these emissions is therefore difficult to observe. Here, the effect is masked by the variation of data. The PAH concentration is lowered by an injection of sulphur additives. The variation in data is though

Influence of sulphur addition on emissions of organic substances during combustion; Inverkan av formen av svaveladditiv paa emissionerna av kolmonoxid och organiska aemnen vid foerbraenning

Energy Technology Data Exchange (ETDEWEB)

Bjurstroem, Henrik; Jonsson, Claes; Almark, Matts; Berg, Magnus; Streibel, Thorsten; Zimmermann, Ralf

2008-02-15

Reduction of emissions of carbon monoxide and organic substances by injecting either ammonium sulphate or elemental sulphur and the importance of the point of injection has been investigated in full scale in a grate-fired bark boiler. The effect was monitored downstream of the economizer and air preheater, immediately upstream of the electrostatic precipitator. Concentrations determined in the comprehensive monitoring program include principally carbon monoxide, TOC and several organic substances, including PAH, PCDD/F and polychlorinated benzenes (PCBz). Additionally, the gaseous PAH were determined on-line using a novel mass spectrometer, REMPI-TOF MS, that measures specifically the 2- to 4-ring PAH's. All concentrations of substances of interest here fluctuate in concert and peak simultaneously. The relationship between the concentrations is not straightforward: there appears to be a threshold in carbon monoxide concentration. Below this threshold, the concentration of organics is low and above it concentrations increase rapidly with increasing carbon monoxide concentration. It has been confirmed that using sulphur additives not only reduces the concentration of carbon monoxide, but also that of organic substances in the flue gases. These additives do not only reduce the mean level of concentrations, but also dampen the fluctuations in these concentrations. Any measure leading to a reduction in carbon monoxide will also decrease the concentration of most organics, under the conditions prevalent in this boiler. Both additives tested are equally effective per kg of pure sulphur. The point of injection, in the fuel or above the grate, is not important. The PCDD/F concentration in the flue gases is very low even without additives, and the effect of sulphur on these emissions is therefore difficult to observe. Here, the effect is masked by the variation of data. The PAH concentration is lowered by an injection of sulphur additives. The variation in data is

Velocity of crack growing of Inconel-600, sensitized, contaminated with sulphur in PWR type reactors

International Nuclear Information System (INIS)

Castano, M. L.; Blazquez, F.; Gomez Briceno, D.; Lagares, A.

1998-01-01

The origin of the vessel head penetration cracking of Jose Cabrera NPP has been attributed to an IGA/SCC process in a highly sensitized Alloy 600 assisted by sulphur species, as both acid sulphates and reduced species originated by the thermal breakdown of the cationic resins present in the primary coolant. The thermal degradation of the cationic resins leads sulphonic acid group scission and sulphates. Under the operating conditions the reduction of sulphates to sulphides is produced. The sulphides formed from the reduction of sulphate can precipitate with metallic cations and be incorporated into the oxide layers of the materials, preferably into nickel alloys. Others components at Jose Cabrera NPP are fabricated from sensitized alloy 600, as bottom vessel penetrations. In order to determine the influence of sulphur incorporated to the oxide layers of bottom vessel penetration alloy 600, an experimental work has been performed to obtained crack growth rate data under PWR primary conditions on sensitized alloy 600. (Author) 5 refs

Mechanism of the transpassive dissolution and secondary passivation of chromium in sulphuric acid solutions

International Nuclear Information System (INIS)

Bojinov, M.; Betova, I.; Raicheff, R.; Fabricius, G.; Laitinen, T.; Saario, T.

1998-01-01

The transpassive dissolution and secondary passivation of Cr in 1..10 M H 2 SO 4 solutions were studied by a combination of different electrochemical methods. The steady-state polarization curves for transpassive dissolution exhibited a Tafel behaviour with a slope being independent on the acid concentration. Lower dissolution rates were measured for higher acid concentrations. Ring-disk measurements showed a release of both soluble Cr(VI) and Cr(III) during transpassivity. Impedance spectra were qualititatively similar in all acid concentrations, comprising one capacitive and two inductive semicircles. A kinetic model comprising two parallel transpassive dissolution paths was consistent with the experimental results. Typical passivation diagrams were observed for Cr in 10 M H 2 SO 4 , and a secondary passive state was established at higher potentials. The formation of the secondary passive film was confirmed by contact electric resistance (CER) measurements. A renewed version of the surface charge approach was consistent with the experimental results in the region of the secondary passivation. (orig.)

Esterification with ethanol to produce biodiesel from high acidity raw materials. Kinetic studies and analysis of secondary reactions

Energy Technology Data Exchange (ETDEWEB)

Pisarello, M.L.; Dalla Costa, B.; Mendow, G.; Querini, C.A. [Instituto de Investigaciones en Catalisis y Petroquimica (INCAPE)-(FIQ-UNL, CONICET), Santiago del Estero 2654-Santa Fe, S3000AOJ (Argentina)

2010-09-15

In this work, the esterification reaction of free fatty acids (FFA) in sunflower oil, coconut oil and concentrated FFA, with ethanol, methanol and ethanol 96%, using homogeneous acid catalysts to produce biodiesel is studied. Kinetic parameters are estimated with a simplified model, and then used to predict the reaction behavior. Reactions other than the reversible esterification are considered to explain the behavior that this system displays. Such reactions are the triglycerides conversion by acid catalyzed transesterification and hydrolysis. In addition, we include kinetic studies of the reaction that occur between the sulphuric acid and methanol (or ethanol), forming mono and dialkylsulphates. This reaction produces water and consumes methanol (or ethanol), and consequently has a direct impact in the esterification reaction rate and equilibrium conversion. The concentration of sulphuric acid decreases to less than 50% of the initial value due to the reaction with the alcohol. A minimum in the acidity due to the free fatty acids as a function of time was clearly observed during the reaction, which has not been reported earlier. This behavior is related to the consecutive reactions that take place during the esterification of FFA in the presence of triglycerides. The phase separation due to the presence of water, which is generated during the reaction, is also studied. (author)

The reducibility of sulphuric acid and sulphate in aqueous solution (translated from German)

International Nuclear Information System (INIS)

Grauer, R.

1990-07-01

In connection with the Swedish project for the final storage of spent fuel elements it was necessary to assess whether dissolved sulphate can corrode the copper canister without the intervention of sulphate-reducing bacteria. A simple reaction between copper and sulphate is thermodynamically impossible. On the other hand, copper can react to give copper sulphide if an additional electron donor such as iron is available. Because little specific information is available about this subject the problem was extended to the much more general question of the reducibility of sulphur in dilute aqueous solution. It is a part of the general knowledge of chemistry, and there is also unanimity about it in the geochemical literature, that purely chemical reduction of sulphate does not take place in dilute solution at temperatures below 100 degrees C. This fact is, however, poorly documented and it was therefore necessary to substantiate it by drawing on numerous individual findings from different areas of pure and applied chemistry. The investigation confirms that sulphur in dilute solution is completely inert towards chemical reducing agents and also to cathodic reduction. Thus corrosion of copper by sulphate under final-storage conditions and in the absence of sulphate reducing bacteria can be ruled out with a probability verging on certainty. (85 refs.)

Development of a Linear Flow Channel Reactor for sulphur removal ...

African Journals Online (AJOL)

2013-09-23

Sep 23, 2013 ... gation of sulphur production in floating sulphur biofilms as a means for addressing this problem. These 50 µm ... Preliminary studies on the use of the FSB system for sulphur removal in Integrated Managed Passive Treatment ...

Fractal and variability analysis of simulations in ozone level due to oxides of nitrogen and sulphur

Science.gov (United States)

Bhardwaj, Rashmi; Pruthi, Dimple

2017-10-01

Air pollution refers to the release of pollutants into the air. These pollutants are detrimental to human the planet as a whole. Apart from causing respiratory infections and pulmonary disorders, rising levels of Nitrogen Dioxide is worsening ozone pollution. Formation of Ground-level ozone involves nitrogen oxides and volatile gases in the sunlight. Volatile gases are emitted from vehicles primarily. Ozone is harmful gas and its exposure can trigger serious health effects as it damages lung tissues. In order to decrease the level of ozone, level of oxides leading to ozone formation has to be dealt with. This paper deals with the simulations in ozone due to oxides of nitrogen and sulphur. The data from Central Pollution Control Board shows positive correlation for ozone with oxides of sulphur and nitrogen for RK Puram, Delhi in India where high concentration of ozone has been found. The correlation between ozone and sulphur, nitrogen oxides is moderate during summer while weak during winters. Ozone with nitrogen and sulphur dioxide follow persistent behavior as Hurst exponent is between 0.5 and 1. The fractal dimension for Sulphur dioxide is 1.4957 indicating the Brownian motion. The behavior of ozone is unpredictable as index of predictability is close to zero.

Distribution of sulphur into products from waste tire pyrolysis

International Nuclear Information System (INIS)

Susa, D.; Haydary, J.; Markos, J.

2012-01-01

Tire pyrolysis is getting growing attention as an effective waste tire disposal method in comparison to environmentally less friendly methods like dumping or incineration. But the scrap tire sulphur content can be a potential obstacle to scrap tire utilization as a fuel. In this paper the distribution of sulphur into tire pyrolysis yields, solid (char) and liquid (tar), was investigated. The pyrolysis experiments were carried out under different conditions to determine the partitioning of sulphur into pyrolysis products. The influence of different temperatures and reaction times was investigated in a laboratory flow reactor under nitrogen atmosphere. Solid and liquid residues were collected and analyzed by elemental analysis. The sulphur content in residual char and tar was determined using an elemental analyzer and the sulphur forms in tar were characterized by the X-ray photoelectron spectroscopy (XPS). (Authors)

Sulphur containing novel extractants for extraction-separation of palladium (II)

International Nuclear Information System (INIS)

Shukla, J.P.; Sawant, S.R.; Anil Kumar; Singh, R.K.

1995-01-01

Extraction performance of palladium (II) by sulphur containing extragents has unequivocally established their strong extraction ability toward this thiophilic soft metal. Hence a comprehensive investigative study was initiated by us to examine selective reversible extraction-separation of trace and macro amounts of palladium (II) from both aqueous nitric acid as well as hydrochloric acid media into 1,2-dichloroethane by 1,10-dithia-18 crown-6 (1,10-DT18C6), S 6 -pentano-36 (S 6 -P-36) and bis (2-ethylhexyl) sulphoxide (BESO) dissolved in toluene. From the study of aqueous phase acidity, reagent concentration, period of equilibration, diluent, strippant and diverse ions, conditions are established from its quantitative and reversible extraction. Recovery of Pd(II) from loaded thiacrown and sulphoxide phase is easily accomplished by using sodium thiocyanate, ammonium thiocyanate, thiourea, sodium thiosulphate and mixture of (2M Na 2 CO 3 + 0.5 NH 4 OH) (only for BESO) as the strippants. The lack of interference from even appreciable amounts of contaminants like 137 Cs, 106 Ru, 233 U and 239 Pu may be considered as one of the outstanding advantages of the method. Application of these extractants has been successfully tested for the recovery of palladium from high active waste matrix. The extracted complex from both the thiacrowns has been characterized by elemental analyses and UV-Visible spectra, confirmed to be PdA 2 .T (A = NO - 3 , Cl - ) from dilute (pH ∼ 2) acid solutions while composition of organic species with palladium for the sulphoxide, has also been confirmed to be disolvate of the type Pd(NO 3 ) 2 .2BESO. (author). 52 refs., 6 tabs., 6 figs

Discontinuities in Jovian sulphur plasma

Energy Technology Data Exchange (ETDEWEB)

Mekler, Y [Jet Propulsion Lab., Pasadena, CA (USA); Eviatar, A; Siscoe, G L

1979-10-01

In recent years, the Jovian sulphur nebula, which is the only component of the thermal plasma in the magnetosphere of Jupiter which emits in the visible, has been the subject of considerable study. A large number of investigators have come up with widely differing models for the density, composition and temperature of the Jovian magnetospheric plasma. In this paper a different characteristic of the sulphur emission, namely its radial distribution is discussed and an attempt is made to assess its implications for the plasma and magnetic field configuration of the inner magnetosphere of Jupiter.

Acid hydrolysis of Curcuma longa residue for ethanol and lactic acid fermentation.

Science.gov (United States)

Nguyen, Cuong Mai; Nguyen, Thanh Ngoc; Choi, Gyung Ja; Choi, Yong Ho; Jang, Kyoung Soo; Park, Youn-Je; Kim, Jin-Cheol

2014-01-01

This research examines the acid hydrolysis of Curcuma longa waste, to obtain the hydrolysate containing lactic acid and ethanol fermentative sugars. A central composite design for describing regression equations of variables was used. The selected optimum condition was 4.91% sulphuric acid, 122.68°C and 50 min using the desirability function under the following conditions: the maximum reducing sugar (RS) yield is within the limited range of the 5-hydroxymethylfurfural (HMF) and furfural concentrations. Under the condition, the obtained solution contained 144 g RS/L, 0.79 g furfural/L and 2.59 g HMF/L and was directly fermented without a detoxification step. The maximum product concentration, average productivity, RS conversion and product yield were 115.36 g/L, 2.88 g/L/h, 89.43% and 64% for L-lactic acid; 113.92 g/L, 2.59 g/L/h, 88.31% and 63.29% for D-lactic acid; and 55.03 g/L, 1.38 g/L/h, 42.66 and 30.57%, respectively, for ethanol using a 7-L jar fermenter. Copyright © 2013. Published by Elsevier Ltd.

MCB-2 concentration meter for boric acid

International Nuclear Information System (INIS)

Lisecki, W.

1978-01-01

The principles are explained of the thermal neutron absorption method for monitoring boric acid concentration in the WWER type reactor coolant. The design principles and the characteristics of four variants are described of the MSB-2 type boric acid concentration monitor developed by IBJ. (B.S.)

Sulphur poisoning of palladium catalysts used for methane combustion: Effect of the support

International Nuclear Information System (INIS)

Escandon, Lara S.; Ordonez, Salvador; Vega, Aurelio; Diez, Fernando V.

2008-01-01

Four different supported palladium catalysts (using alumina, silica, zirconia and titania as supports), prepared by incipient wetness impregnation, were tested as catalysts for methane oxidation in presence of sulphur dioxide. The catalyst supported on zirconia showed the best performance, whereas the silica-supported one showed the fastest deactivation. Temperature-programmed desorption experiments of the poisoned catalysts suggest that SO 2 adsorption capacity of the support plays a key role in the catalyst poisoning. In order to study the effect of promoters, expected to improve the thermal stability and thioresistance of the catalyst, commercial zirconia modified by yttrium and lantane was tested as supports. It was found that the presence of these promoters does not improve the performance of the zirconia-supported catalyst. A deactivation model - considering two different active sites (fresh and poisoning), pseudo-first order dependence on methane concentration and poisoning rate depending on sulphur concentration and fraction of non-poisoned palladium - was used for modelling the deactivation behaviour

The fate of sulphur in the Cu-based Chemical Looping with Oxygen Uncoupling (CLOU) Process

International Nuclear Information System (INIS)

Adánez-Rubio, Iñaki; Abad, Alberto; Gayán, Pilar; García-Labiano, Francisco; Diego, Luis F. de; Adánez, Juan

2014-01-01

Highlights: • 15 h of CLOU experiments using lignite were carried out in a continuously unit. • The sulphur split between fuel- and air-reactor streams in the process was analysed. • Most of the sulphur introduced with the fuel exits as SO 2 at the fuel-reactor. • The use of a carbon separation system to reduce the S emission was evaluated. • Coals with high S content can be burnt in a CLOU process with a Cu-based material. - Abstract: The Chemical Looping with Oxygen Uncoupling (CLOU) process is a type of Chemical Looping Combustion (CLC) technology that allows the combustion of solid fuels with air, as with conventional combustion, through the use of oxygen carriers that release gaseous oxygen inside the fuel reactor. The aim of this work was to study the behaviour of the sulphur present in fuel during CLOU combustion. Experiments using lignite as fuel were carried out in a continuously operated 1.5 kW th CLOU unit during more than 15 h. Particles containing 60 wt.% CuO on MgAl 2 O 4 , prepared by spray drying, were used as the oxygen carrier in the CLOU process. The temperature in the fuel reactor varied between 900 and 935 °C. CO 2 capture, combustion efficiency and the sulphur split between fuel and air reactor streams in the process were analysed. Complete combustion of the fuel to CO 2 and H 2 O was found in all experiments. Most of the sulphur introduced with the fuel exited as SO 2 at the fuel reactor outlet, although a small amount of SO 2 was measured at the air reactor outlet. The SO 2 concentration in the air reactor exit flow decreased as the temperature in the fuel reactor increased. A carbon capture efficiency of 97.6% was achieved at 935 °C, with 87.9 wt.% of the total sulphur exiting as SO 2 in the fuel reactor. Both the reactivity and oxygen transport capacity of the oxygen carrier were unaffected during operation with a high sulphur content fuel, and agglomeration problems did not occur. Predictions were calculated regarding the use

Solvent extraction of titanium (IV) from sulphuric acid media by cyanex 921 and tri-butylphosphate

International Nuclear Information System (INIS)

Nayl, A.A.; Aly, H.F.

2009-01-01

titanium and its compounds found different useful applications in the nuclear and radioactive waste treatment fields. extraction behavior of titanium (IV) from sulfuric acid by commercial tri-octylphosphine oxide (CYANEX 921) and tributylphosphate (TBP)has been investigated. effects of contact time, sulfuric acid concentration in the aqueous phase, the extractants concentration in the organic phase, and the temperature on the extraction of titanium by the two systems were studied. it is found that extraction equilibrium of titanium is reached after 10-15 min and 4 min for CYANEX 921 and TBP, respectively . the extraction of Ti(IV) by 0.15 M CYANEX 921 in kerosene increases with the increase in sulfuric acid concentration to reach a maximum extraction of 91% at 7.0 m acid concentration. for the TBP system, the maximum extraction of titanium was 79% using 1.0 M TBP in kerosene from 4.0 m H 2 SO 4 solution . the effect of temperature was also evaluated. Na 2 CO 3 was used as a good stripping agent compared with other reagents. the interaction of Ti(IV) in sulfate medium and different sulfate species in sulfuric acid are reviewed. within the literature survey together with analysis of the extraction results , it can be concluded that titanium extracted by CYANEX 921 as Ti O (HSO 4 ) 2 .2 CYANEX 921 whereby in case of TBP, the extracted species is TiOSO 4 .2 TBP

Short term effects of ambient sulphur dioxide and particulate matter on mortality in 12 European cities : Results from time series data from the APHEA project

NARCIS (Netherlands)

Katsouyanni, K; Touloumi, G; Spix, C; Schwartz, J; Balducci, F; Medina, S; Rossi, G; Wojtyniak, B; Sunyer, J; Bacharova, L; Schouten, JP; Ponka, A; Anderson, HR

1997-01-01

Objectives: To carry out a prospective combined quantitative analysis of the associations between all cause mortality and ambient particulate matter and sulphur dioxide. . Design: Analysis of time series data on daily number of deaths from all causes and concentrations of sulphur dioxide and

Sulphur self–retention and sulphur dioxide capture with active calcium minerals in mineral–rich coals / Mchabe, D.

OpenAIRE

Mchabe, Dursman

2011-01-01

In order to provide information for the development of clean coal technology, the sulphur self–retention and sulphur dioxide capturing properties of minerals present in low grade coals was investigated. This study consisted of detailed mineral analyses of coal and ash samples using results obtained from QEMSCAN and separate retention (coal) and capture (ash) experiments with laboratory scale reactors. Typical South African coal samples were used in this study. The ash content v...

Muon transfer to sulphur dioxide

International Nuclear Information System (INIS)

Mulhauser, F.; Schneuwly, H.

1993-01-01

A systematic study of muon capture and muon transfer has been performed in seven different H 2 + SO 2 gas mixtures. From the single-exponential time structure of the muonic sulphur x-rays, one determines the lifetime of the μp atoms under the given experimental conditions. The reduced muon transfer rates to the sulphur dioxide molecule, deduced from these lifetimes, all agree well with each other. The muonic oxygen time spectra show an additional structure as if μp atoms of another kind were present. Comparable time structures are observed in a D 2 + SO 2 mixture. (author)

Availability and uptake of sulphur by mustard in three soils in Udaipur valley

International Nuclear Information System (INIS)

Kataria, S.K.; Shriniwas

1976-01-01

The differential behaviour of three soils (Bargaon, Bhatewar red and Bhatewar black) for availability of sulphur to mustard was studied in a greenhouse pot culture experiment using five doses of sulphur (0,20,40,80,120 ppm) applied as 35 S tagged ammonium sulphate. Application of sulphur significantly increased the dry matter of mustard over control, however, maximum dry matter was obtained when sulphur was applied at 40 ppm level, thereafter, any higher doses did not prove beneficial. Sulphur content in the plant tissue and percent of sulphur in the plant derived from fertilizer increased with successive doses of applied sulphur. (author)

SULPHUR AVAILABILITY IN BRAZILIAM SOILS: RESPONSE TO SULPHUR FERTILIZING IN PRESENCE AND AUSENCE OF LIMING DISPONIBILIDADE DE ENXOFRE EM SOLOS BRASILEIROS: RESPOSTA À ADUBAÇÃO SULFATADA NA PRESENÇA E AUSÊNCIA DE CALAGEM

Directory of Open Access Journals (Sweden)

Eurípedes Malavolta

2007-09-01

Full Text Available

A greenhouse experiment was carried out with surface samples of 12 soils from the States of São Paulo, Minas Gerais and Goiás (Brazil. Carbon (C content varied from 0.50 to 3.03%, sulphur from 0.0104 to 0.0319% and clay varied from 8 to 60%. Corn (Zea mays L. was grown in two successive croppings in presence of three rates of S (0, 20 and 40 ppm applied as gypsum, previously incubated in presence and absence of lime. Dry matter production did not show significant difference due to the two croppings of the soils; sulphur uptake, otherwise, was thoroughly lower in the second cropping, indicating the depletion of native and applied sulphur. Sandy soils have a lower supplying power of sulphur due to its effective small reserve. Clayey soils, moreover “cerrado” soils with higher carbon contents, possess greater croppings and sulphur uptake potentials, provided the soil acidity is neutralized. Liming, besides its role as soil acidity neutralizer and as calcium and magnesium supplier, showed positive interaction with sulphur and a synergistic effect on the depletion of soils native sulphur. The rates of sulphur which maximized dry matter yield and sulphur absorption varied in the range of 20 to 70 ppm, being the highest requirements found in clayey soils with no liming.

Conduziu-se um experimento em casa de vegetação com amostras superficiais de 12 solos, provenientes dos Estados de São Paulo, Minas Gerais e Goiás (Brasil, com teores de carbono variando entre 0,5 e 3,03%, de enxofre total entre 0,0104 e 0,319% e de argila entre 8 e 60%. Os solos foram submetidos a dois cultivos sucessivos com milho (Zea mays L., com os tratamentos: 12 solos, 3 doses de gesso (0, 20 e 40 ppm de S, previamente incubados na ausência e presença de calagem. A produção de matéria seca da parte a

Energetic and exergetic life cycle analysis to explain the hidden costs and effects of current sulphur utilisation

NARCIS (Netherlands)

Brehmer, B.; Sanders, J.P.M.

2007-01-01

Typically life cycle analyses of the fertiliser industry are based on averages of outdated technology. Sulphur is a major element, emerging as a primary nutrient on its own accord and as a feed for other fertiliser production, namely phosphoric acid. Recent developments sparked by governmental

High Concentrations of Tranexamic Acid Inhibit Ionotropic Glutamate Receptors.

Science.gov (United States)

Lecker, Irene; Wang, Dian-Shi; Kaneshwaran, Kirusanthy; Mazer, C David; Orser, Beverley A

2017-07-01

The antifibrinolytic drug tranexamic acid is structurally similar to the amino acid glycine and may cause seizures and myoclonus by acting as a competitive antagonist of glycine receptors. Glycine is an obligatory co-agonist of the N-methyl-D-aspartate (NMDA) subtype of glutamate receptors. Thus, it is plausible that tranexamic acid inhibits NMDA receptors by acting as a competitive antagonist at the glycine binding site. The aim of this study was to determine whether tranexamic acid inhibits NMDA receptors, as well as α-amino-3-hydroxy-5-methyl-4-isoxazolepropionic acid and kainate subtypes of ionotropic glutamate receptors. Tranexamic acid modulation of NMDA, α-amino-3-hydroxy-5-methyl-4-isoxazolepropionic acid, and kainate receptors was studied using whole cell voltage-clamp recordings of current from cultured mouse hippocampal neurons. Tranexamic acid rapidly and reversibly inhibited NMDA receptors (half maximal inhibitory concentration = 241 ± 45 mM, mean ± SD; 95% CI, 200 to 281; n = 5) and shifted the glycine concentration-response curve for NMDA-evoked current to the right. Tranexamic acid also inhibited α-amino-3-hydroxy-5-methyl-4-isoxazolepropionic acid receptors (half maximal inhibitory concentration = 231 ± 91 mM; 95% CI, 148 to 314; n = 5 to 6) and kainate receptors (half maximal inhibitory concentration = 90 ± 24 mM; 95% CI, 68 to 112; n = 5). Tranexamic acid inhibits NMDA receptors likely by reducing the binding of the co-agonist glycine and also inhibits α-amino-3-hydroxy-5-methyl-4-isoxazolepropionic acid and kainate receptors. Receptor blockade occurs at high millimolar concentrations of tranexamic acid, similar to the concentrations that occur after topical application to peripheral tissues. Glutamate receptors in tissues including bone, heart, and nerves play various physiologic roles, and tranexamic acid inhibition of these receptors may contribute to adverse drug effects.

Inhibitive action of some plant extracts on the corrosion of steel in acidic media

Energy Technology Data Exchange (ETDEWEB)

Abdel-Gaber, A.M. [Department of Chemistry, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt)]. E-mail: ashrafmoustafa@yahoo.com; Abd-El-Nabey, B.A. [Department of Chemistry, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt); Sidahmed, I.M. [Department of Chemistry, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt); El-Zayady, A.M. [Department of Chemistry, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt); Saadawy, M. [Department of Chemistry, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt)

2006-09-15

The effect of extracts of Chamomile (Chamaemelum mixtum L.), Halfabar (Cymbopogon proximus), Black cumin (Nigella sativa L.), and Kidney bean (Phaseolus vulgaris L.) plants on the corrosion of steel in aqueous 1 M sulphuric acid were investigated by electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization techniques. EIS measurements showed that the dissolution process of steel occurs under activation control. Potentiodynamic polarization curves indicated that the plant extracts behave as mixed-type inhibitors. The corrosion rates of steel and the inhibition efficiencies of the extracts were calculated. The results obtained show that the extract solution of the plant could serve as an effective inhibitor for the corrosion of steel in sulphuric acid media. Inhibition was found to increase with increasing concentration of the plant extract up to a critical concentration. The inhibitive actions of plant extracts are discussed on the basis of adsorption of stable complex at the steel surface. Theoretical fitting of different isotherms, Langmuir, Flory-Huggins, and the kinetic-thermodynamic model, were tested to clarify the nature of adsorption.

Effect of sulphur on the strengthening of a Zr-Nb alloy

International Nuclear Information System (INIS)

Chang, K.I.; Hong, S.I.

2008-01-01

The effect of sulphur on the strengthening and the thermally activated deformation of cold-worked Zr-1 Nb alloy was investigated. In the present study, the sulphur strengthening was observed even at room temperature unlike the previous study of Ferrer et al. The flow stress increased by 65 MPa at room temperature with the addition of sulphur as little as 20 ppm. With further increase of sulphur content up to 300 ppm, negligible change of the flow stress was observed. The additive strengthening behavior in which the entire stress-strain curve shift upward by the friction stress due to the addition of sulphur was observed in the Zr-Nb alloy of the present study. The activation volume decreased slightly (from 110b 3 to 80b 3 ) with the addition of 300 ppm sulphur at room temperature. The rate-controlling mechanism of the deformation can best be explained by the dislocation interaction mechanism in which the segregation of alloying elements such as oxygen and sulphur atoms affects the activation length of dislocations

Production of Itaconic Acid from Jatropha curcas Seed Cake by Aspergillus terreus

Directory of Open Access Journals (Sweden)

Amina M. AHMED EL-IMAM

2013-02-01

Full Text Available Submerged substrate fermentation of Jatropha seed cake, a by-product of oil extraction from Jatropha curcas seed was carried out using Aspergillus terreus for the production of itaconic acid. The Jatropha seed cake was initially converted into fermentable sugars by dilute acid hydrolysis using 50% sulphuric acid. The rate of hydrolysis was 1.04 gL-1. The fermentation process was carried out at room temperature, agitation of 400 rpm and three physico-chemical parameters (pH, inoculum size and substrate concentration were varied. Itaconic acid and glucose assays were carried out by spectrophotometry and Dinitrosalicylic acid methods respectively daily. Maximum yield of itaconic acid was 48.70 gL-1 at 5 ml of inoculum size, 50 g substrate concentration and pH 1.5. The residual glucose concentration increased for the first two days of fermentation after which it began to decrease as the itaconic acid concentration increased. The least concentration of itaconic acid observed was 6.00 gL-1, obtained after 24 hours of fermentation with 4 ml inoculum size, 50 g substrate concentration and at pH 1.5. The findings of this work indicate that Jatropha curcas seed cake is a suitable substrate for itaconic acid production.

Organically bound sulphur in coal: A molecular approach

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Leeuw, J.W. de

1992-01-01

A critical review of literature concerning the molecular characterization of low and high molecular weight organosulphur constitutents present in coal as well as a detailed analysis of organic sulphur compounds present in flash evaporates and pyrolysates of a suite of coals ranging in sulphur

Association between Serum Unmetabolized Folic Acid Concentrations and Folic Acid from Fortified Foods.

Science.gov (United States)

Palchetti, Cecília Zanin; Paniz, Clóvis; de Carli, Eduardo; Marchioni, Dirce M; Colli, Célia; Steluti, Josiane; Pfeiffer, Christine M; Fazili, Zia; Guerra-Shinohara, Elvira Maria

2017-01-01

To investigate the association between serum unmetabolized folic acid (UMFA) concentrations and folic acid from fortified foods and nutrients known as dietary methyl-group donors (folate, methionine, choline, betaine and vitamins B2, B6 and B12) in participants exposed to mandatory fortification of wheat and maize flours with folic acid. Cross-sectional study carried out with 144 healthy Brazilian participants, both sexes, supplement nonusers. Serum folate, UMFA, vitamin B12 and total plasma homocysteine (tHcy) were biochemically measured. Dietary intake was assessed by 2 non-consecutive 24-hour dietary recalls (24-HRs) and deattenuated energy-adjusted nutrient data were used for statistical analysis. Ninety eight (68.1%) participants were women. Median (interquartile range) age was 35.5 (28.0-52.0) years. Elevated serum folate concentrations (>45 nmol/L) were found in 17 (11.8%), while folate deficiency ( 1 nmol/L (90th percentile). UMFA concentrations were positively correlated with folic acid intake and negatively correlated to choline, methionine and vitamin B6 intakes. Participants in the lowest quartile of UMFA concentrations had lower dietary intake of total folate (DFEs) and folic acid, and higher dietary intake of methionine, choline and vitamin B6 than participants in the highest quartile of UMFA. Folic acid intake (OR [95% CI] = 1.02 [1.01-1.04)] and being a male (OR [95% CI] = 0.40 [0.19-0.87) were associated with increased and reduced odds for UMFA concentrations > 0.55 nmol/L (median values), respectively. UMFA concentrations were directly influenced by folic acid intake from fortified foods in a healthy convenience sample of adult Brazilians exposed to mandatory flour fortification with folic acid.

Amino acid composition of some Mexican foods.

Science.gov (United States)

Morales de León, Josefina; Camacho, M Elena; Bourges, Héctor

2005-06-01

Knowledge of the amino acid composition of foods is essential to calculate their chemical score, which is used to predict protein quality of foods and diets. Though amino acid composition of many foods is reasonably well established, better knowledge is needed on native foods consumed in different regions and countries. This paper presents the amino acid composition of different presentations of raw and processed foods produced and consumed in Mexico. The amino acid composition was determined using Beckman amino acid analyzers (models 116 and 6300). Tryptophan was determined using the Spies and Chambers method. Of the different foods analyzed, some comments are made on native or basic foods in Mexico: Spirulin, where lysine is the limiting amino acid, with a chemical score of 67%, is a good source of tryptophan (1.16g/16 gN); amaranth contains high levels of sulphur amino acids (4.09 to 5.34 g/16gN), with a protein content of 15 g/100g; and pulque, a Pre-Hispanic beverage that contains high levels of tryptophan (2.58 g/16 gN) and sulphur amino acids (2.72 g/16 gN). Finally, insects are good sources of sulphur amino acids and lysine.

Reactions of sulphur mustard on impregnated carbons.

Science.gov (United States)

Prasad, G K; Singh, Beer

2004-12-31

Activated carbon of surface area 1100 m2/gm is impregnated with 4% sodium hydroxide plus 3% Cr(VI) as CrO3 with and without 5% ethylene diamine (EDA), 4% magnesium nitrate and 5% ruthenium chloride by using their aqueous solutions. These carbons are characterized for surface area analysis by BET conventional method and exposed to the vapours of sulphur mustard (HD) at room temperature (30 degrees C). After 24 h, the reaction products are extracted in dichloromethane and analyzed using gas chromatography and mass spectrometry (GC-MS). Hemisulphur mustard, thiodiglycol, 1,4-oxathiane are observed to be the products of reaction between sulphur mustard and NaOH/CrO3/C system, whereas on NaOH/CrO3/EDA/C system HD reacted to give 1,4-thiazane. On Mg(NO3)2/C system it gave hemisulphur mustard and thiodiglycol. On RuCl3/C system it degraded to divinyl sulphone. Residual sulphur mustard is observed along with reaction products in all systems studied. Reaction mechanisms are also proposed for these interesting surface reactions. Above-mentioned carbons can be used in filtration systems for protection against hazardous gases such as sulphur mustard.

Reactions of sulphur mustard on impregnated carbons

International Nuclear Information System (INIS)

Prasad, G.K.; Singh, Beer

2004-01-01

Activated carbon of surface area 1100 m 2 /gm is impregnated with 4% sodium hydroxide plus 3% Cr(Vi) as CrO 3 with and without 5% ethylene diamine (EDA), 4% magnesium nitrate and 5% ruthenium chloride by using their aqueous solutions. These carbons are characterized for surface area analysis by BET conventional method and exposed to the vapours of sulphur mustard (HD) at room temperature (30 deg. C). After 24 h, the reaction products are extracted in dichloromethane and analyzed using gas chromatography and mass spectrometry (GC-MS). Hemisulphur mustard, thiodiglycol, 1,4-oxathiane are observed to be the products of reaction between sulphur mustard and NaOH/CrO 3 /C system, whereas on NaOH/CrO 3 /EDA/C system HD reacted to give 1,4-thiazane. On Mg(NO 3 ) 2 /C system it gave hemisulphur mustard and thiodiglycol. On RuCl 3 /C system it degraded to divinyl sulphone. Residual sulphur mustard is observed along with reaction products in all systems studied. Reaction mechanisms are also proposed for these interesting surface reactions. Above-mentioned carbons can be used in filtration systems for protection against hazardous gases such as sulphur mustard

A new technology aimed at re-establishing a global sulphur supply/demand balance

International Nuclear Information System (INIS)

Slavens, A.F.; Jorgensen, C.; Ogg, D.

2009-01-01

The world's sulphur supply is mainly determined by involuntary production of elemental sulphur during the processing of oil and gas. As a result, sulphur supply is decoupled from demand, resulting in an imbalance between the two. For almost two decades, sulphur supply has exceeded demand, which has raised significant concerns for oil and gas producers such as where to store all of the excess sulphur, and how to transport a low-value commodity to market in an economically attractive fashion. Black and Veatch is involved in the development of a new technology called sulphur to energy process (STEP TM ) which has the potential to assist in balancing global sulphur supply and demand, as well as affording other benefits such as low-emission energy production. This paper presented the potential merits of the STEP as a means to reestablish a global sulphur supply/demand balance for the world trading market. It explored the other potential benefits that may result from the use of this new technology and compared STEP to other technologies and operating schemes that regulate sulphur supply. It was concluded that STEP has the potential to allow the processor to produce elemental sulphur when demand is high, or to provide safe and ecological disposal when demand is low, with the added benefits of energy recovery from the sulphur combustion process, and sour gas reservoir sweetening over time as sulphur dioxide reacts with hydrogen sulphide present in the reservoir. 13 refs., 3 tabs., 22 figs

Acid leaching of coal: to produce clean fuels from Turkish lignite

Energy Technology Data Exchange (ETDEWEB)

Seferinoglu, Meryem [Mineral Research and Exploration Directorate (Turkey)], email: meryem_seferinoglu66@yahoo.com; Duzenli, Derya [Ankara Central Laboratory (Turkey)

2011-07-01

With the increasing concerns about the environment, energy producers and governments are looking at developing clean energy sources. However, Turkey has limited clean energy resources and is using low grade coal which has high sulphur content as an alternative energy source. The aim of this paper is to study the possibility of generating clean fuel from Edirne Lignite and to get a better understanding of chemical mechanisms involved in coal leaching with hydrofluoric acid (HF) solutions. Leaching was conducted on Edirne Lignite with HF solution at ambient temperature and the effects of parameters such as reaction time and concentration of acid solutions on the process were evaluated. The optimum conditions were found and it was shown that ash levels can be reduced from 28.9% to 10.5% and the calorific value increased by 500kcal/kg with the HF leaching method. This study demonstrated that the production of clean fuel from high sulphur lignite is possible.

Increasing the efficiency of sulphur dioxide in wine by using of saturated higher fatty acids

Directory of Open Access Journals (Sweden)

Petra Bábíková

2012-01-01

Full Text Available This work is aimed on stopping of alcoholic fermentation to leave residual sugar and the possibility of sulfur dioxide reduction in wine technology and storage. As a very good opportunity showed mixture of higher saturated fatty acids with a reduced dose of sulfur dioxide. Experiments have confirmed that the concentration of viable yeasts in 1 ml of wine for variants treated with a mixture of fatty acids is significantly lower than in variants treated with sulfur dioxide alone. Then was monitored the influence of fatty acids on stored wine with residual sugar. At this point a dramatically prolongation of interval to secondary fermentation (depreciation of wine in the bottle was confirmed. Finally, attention was paid to influence on the organoleptic characteristics of wine treated this way. In this case, it is possible to consider the recommended concentration of fatty acid below the threshold of susceptibility.

SULPHUR CONTAINING LICKS AND THEIR EFFECT ON THE ...

African Journals Online (AJOL)

amounts of sulphur, there are some of particular importance such as the vitamins thiamine and biotin. Sulphur is also ingested in the inorganic sulphide and sulphate forms, fractions of which are utilized in metabolic processes, whereas substantial portions are also excreted. It has been determined that thiol cornpounds.

Role of sulphur in rice production

International Nuclear Information System (INIS)

Sachdev, Pamila; Sachdev, M.S.

2002-01-01

Sulphur is an essential plant nutrient growing in international importance. Rice farmers usually apply nitrogen, phosphorus and potassium at high rates to the crop. Whenever there is an imbalance between off take and input of nutrients, it may lead to a decline in soil fertility and increase incidence of deficiencies of certain plant nutrients especially sulphur and zinc. On the basis of available information, nutritional requirement, uptake values, crop response and measures to overcome S deficiency are some of the aspects critically dealt with

Radiation-induced graft copolymerization of methyl acrylate and acrylic acid onto rubber wood fiber

International Nuclear Information System (INIS)

Saliza Jam; Mansor Ahmad; Wan Md Zin Wan Yunus; Khairul Zaman Mohd Dahlan

2001-01-01

Graft copolymerization of methyl acrylate and acrylic acid monomers onto rubber wood fiber (RWF) was carried out by simultaneous radiation-induced technique. The parameters affecting the grafting reaction were investigated and the optimum conditions for both monomers obtained are as follows: impregnation time = 16 hours, total dose = 30 kGy, methanol : water ratio, 3:1, monomers concentration = 40 v/v % and sulphuric acid concentration = 0.1 mol/L. Fourier Transform Infrared (FTIR), thermogravimetry analysis (TGA), and scanning electron microscope (SEM) analyses used to characterize graft copolymers. The structural investigation by x-ray diffraction (XRD) shows the degree of crystallinity of rubber wood fiber decreased with the incorporation of poly(methyl acrylate) and poly(acrylic acid) grafts. (Author)

Serum bile acid concentrations in dairy cattle with hepatic lipidosis.

Science.gov (United States)

Garry, F B; Fettman, M J; Curtis, C R; Smith, J A

1994-01-01

This study was designed to evaluate serum bile acid measurements as indicatory, of liver function and/or hepatic fat infiltration in dairy cattle. Serum bile acid concentrations were measured in healthy dairy cattle at different stages of lactation after fasting or feeding. Bile acid concentrations were compared with liver fat content and sulfobromophthalein (BSP) half-life (T 1/2). Serum bile acid concentrations were higher in cows in early lactation and with higher daily milk production. Compared with prefasting values, bile acid concentrations were decreased at 8, 14, and 24 hours of fasting. Blood samples from fed cows at 1- to 2-hour intervals had wide and inconsistent variations in bile acid concentration. Because serum bile acids correlated well with BSP T 1/2, it is suggested that both measurements evaluate a similar aspect of liver function. Neither bile acids nor BSP T 1/2 correlated with differences in liver fat content among cows. Because of large variability in serum bile acid concentrations in fed cows and the lack of correlation of measured values with liver fat content, bile acid determinations do not appear useful for showing changes in hepatic function in fed cows with subclinical hepatic lipidosis nor serve as a screening test for this condition.

Levels of cystathionine gamma lyase production by Geotrichum candidum in synthetic media and correlation with the presence of sulphur flavours in cheese.

Science.gov (United States)

Gente, Stéphanie; La Carbona, Stéphanie; Guéguen, Micheline

2007-03-10

Geotrichum candidum is a cheese-ripening agent with the potential to produce sulphur flavour compounds in soft cheeses. We aimed to develop an alternative test for predicting the aromatic (sulphur flavours) potential of G. candidum strains in soft cheese. Twelve strains of G. candidum with different levels of demethiolase activity (determined by a chemical method) in YEL-met (yeast extract, lactate methionine) medium were studied. We investigated cgl (cystathionine gamma lyase) gene expression after culture in three media - YEL-met, casamino acid and curd media - and then carried out sensory analysis on a Camembert cheese matrix. We found no correlation between demethiolase activity in vitro and cgl gene expression. Sensory analysis (detection of sulphur flavours) identified different aromatic profiles linked to cgl expression, but not to demethiolase activity. The RT-PCR technique described here is potentially useful for predicting the tendency of a given strain of G. candidum to develop sulphur flavours in cheese matrix. This is the first demonstration that an in vitro molecular approach could be used as a predictive test for evaluating the potential of G. candidum strains to generate sulphur compounds in situ (Camembert cheese matrix).

Effect of oxygen potential on sulphur dioxide activation of oil sands fluid coke and characteristics of activated coke in mercury adsorption

International Nuclear Information System (INIS)

Morris, E.A.; Jia, C.Q.; Tong, S.

2007-01-01

A sulphur-impregnated activated carbon (SIAC) technology was modified for use in copper smelters in order to mitigate mercury and sulphur dioxide (SO 2 ) emissions. Elemental sulphur was captured as a co-product. The study examined the feasibility of reducing levels of SO 2 using fluid coke in the copper smelter flue. SIAC properties were optimized in order to capture vapour phase mercury. Raw fluid coke samples were used to measure SO 2 flow rates. Gas composition was varied to mimic concentrations found during normal operation of copper converters. Gas chromatography was used to analyze reactions products and to prove the hypothesis that mercury capacity is influenced by the oxygen potential of the activation gas due to changes in surface sulphur types developed from reduced sulphur species. Results of the study showed that oxygen levels at 5 per cent did not play a significant role in pore development. It was concluded that increased residence times contributed to reductions in SO 2 and elemental S yields. 13 refs., 1 tab., 7 figs

Recovery of alumina from khushab bauxite by leaching with sulphuric acid and removal of iron impurity by ethanol

International Nuclear Information System (INIS)

Tariq, M.; Iqbal, M.M.; Shafiq, M.; Aziz, A.

2014-01-01

Bauxite is heterogeneous material principally composed of aluminum oxide minerals and found in all continents. It is being used in chemical, cement, refractory, abrasive, fertilizer, steel and other industries. In order to extract the alumina, the calcined samples of bauxite of Khushab area were ground to -710 meum. Sulphuric acid of purity 40% was used as leaching agent and slurry of pulp density 14% was prepared by dissolving 60 ml acid in 20 gm sample. The leaching was carried out at 90 degree C for 2 hours. The iron impurity was removed by ethanol of purity 68%. The drying, dehydration and desulphurization temperatures were kept 105 degree C, 450 degree C and 850 degree C respectively in all the stages of the process. Alumina recoveries from four samples of Sultan Mehdhi, Chamil More, Niaz Mine and Nadi locations were 20.8%, 9.81%, 15.47% and 7.78% respectively. Iron was almost completely removed as the analysis shows that the Fe/sub 2/O/sub 3/ removal was from 97.8% to 99.6%. It is concluded that leaching efficiency was quite encouraging except Nadi ore sample. However the iron free alumina recoveries were low as the analysis of Fe/sub 2/O/sub 3/ processed residue shows that it contains 72.72% to 92.94% of leached alumina in all the four experiments. (author)

Studies on the microbial sulphur cycle in acid ponds in the Niederlausitz mining region in Brandenburg; Untersuchungen zum mikrobiellen Schwefelkreislauf in sauren Tagebau-Restseen der Niederlausitz (Brandenburg)

Energy Technology Data Exchange (ETDEWEB)

Meier, J

2001-07-01

The water quality of the acid ponds in the Niederlausitz brown coal mining region is characterised by pH values below 3 and high concentrations of dissolved iron (up to 10 mM) and sulphate (up to 30 mM). The development of these ponds is determined by the equilibrium that arises between acidifying and alkalinising processes. Acidity develops through weathering and oxidation of iron sulphides in the mining refuse, whereas alkalinity arises through the reduction of iron (III) and sulphate in the pond sediments, a process associated with the oxidation of organic matter. The purpose of the present study was to examine the influence of sulphate reduction and sulphur oxidation on the neutralising potential of the sediments in acid ponds and to characterise and identify the microorganisms involved in these processes. Comparative explorations were performed in two acid waters, namely ponds 111 and 107, and in a neutral water, namely pond B, in a semi-natural area of the Niederlausitz region. [German] Die Wasserqualitaet der sauren Bergbau-Restseen im Braunkohlerevier der Niederlausitz ist durch pH-Werte unter pH 3 und hohe Konzentrationen an geloestem Eisen (bis zu 10 mM) und Sulfat (bis zu 30 mM) gekennzeichnet. Die Entwicklung der Restseen wird durch das Gleichgewicht von aziditaets- und alkalinitaetsbildenden Prozessen bestimmt. Aziditaet entsteht bei der Verwitterung bzw. der Oxidation der Eisensulfide im Kippmassiv, waehrend Alkalinitaet bei der an die Oxidation organischer Substanz gekoppelte Reduktion von Eisen(III) und Sulfat in den Sedimenten der Seen gebildet wird. In der vorliegenden Arbeit wurde der Einfluss der Sulfratreduktion und der Schwefeloxidation auf das Neutralisierungspotenzial der Sedimente der sauren Restseen untersucht sowie die an diesen Prozessen beteiligten Mikroorganismen charakterisiert und identifiziert. Vergleichende Untersuchungen wurden in zwei sauren, Restsee 111 und 107, und in einem neutralen Gewaesser, Restsee B, im naturnahen Bereich

Mathematical modelling of demineralisation of high sulphur coal by bioleaching

Energy Technology Data Exchange (ETDEWEB)

Weerasekara, N.S.; Frutos, F.J.G.; Cara, J.; Lockwood, F.C. [University of London Imperial College of Science Technology & Medicine, London (United Kingdom)

2008-02-15

During coal combustion various toxic compounds are generated from its sulphur content. Their environmental impacts are considered to be very important. While there are various conventional preparation methods to remove the sulphur in the fuel, recent work reveals that newly-isolated micro-organisms, naturally present in coal, have the ability to reduce its sulphur content. The removal of sulphur using biological leaching involving acidophilic iron oxidising bacteria like Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans are examined and a computational technique based on computational fluid dynamics is developed to model the biological leaching of sulphur from coal. The model was validated against a pack-column experiment carried out for iron separation during 60 days. The mathematical model predicted iron separation over time is similar to experimental measurements, with an average difference of 5.5%. According to the experimental results, there was an overall reduction of 33% of pyrite, whereas the model prediction was 32%. The model results shows overall good agreement with pack-column experimental data.

Transformation and Deposition of Sulphur and Nitrogen Compounds in the Marine Boundary Layer

Energy Technology Data Exchange (ETDEWEB)

Hertel, O

1995-10-01

In this thesis the author performs a model study of the transformation and deposition of sulphur and nitrogen compounds in the marine boundary layer, including source-receptor relationships. The central part of the study is the development and testing of a variable scale trajectory model for Europe, with special emphasis on modelling the concentrations of gases and aerosols in the marine atmosphere and the deposition to sea. A one-dimensional version of the model was developed to model the chemical degradation of dimethyl sulphide (DMS) in the marine boundary layer. Although the model reproduces the observed levels of DMS and methane sulphonic acid (MSA) well, the calculated DMS concentration is not always in phase with observed levels, probably because of a local coastal emission that is correlated with the shifting tide. Another version of the trajectory model, Atmospheric Chemistry and Deposition model (ACDEP), was developed to study the deposition of nitrogen compounds to the Danish sea waters. This model uses a new numerical scheme, the Eulerian Backward Iterative method. The model is able to reproduce observations of air concentrations and wet deposition fairly well; data for dry deposition were not available. The model was also used for calculation of deposition of nitrogen compounds to the Kattegat. Finally, a sensitivity study was performed on the model. 175 refs., 87 figs., 32 tabs.

The nitric acid decomposition of calcined danburite concentrate of Ak-Arkhar Deposit

International Nuclear Information System (INIS)

Kurbonov, A.S.; Mamatov, E.D.; Suleymani, M.; Borudzherdi, A.; Mirsaidov, U.M.

2011-01-01

Present article is devoted to nitric acid decomposition of calcined danburite concentrate of Ak-Arkhar Deposit of Tajikistan. The obtaining of boric acid from pre backed danburite concentrate by decomposition of nitric acid was studied. The chemical composition of danburite concentrate was determined. The laboratory study of danburite leaching by nitric acid was conducted. The influence of temperature, process duration, nitric acid concentration on nitric acid decomposition of calcined danburite concentrate of Ak-Arkhar Deposit was studied as well. The optimal conditions of nitric acid decomposition of calcined danburite concentrate of Ak-Arkhar Deposit, including temperature, process duration, nitric acid concentration and particle size were proposed.

Antioxidant and antibacterial properties of Ziziphus mucronata and ...

African Journals Online (AJOL)

sulphuric acid reagent, Fehling's solution, concentrated sulphuric acid, ferric chloride, Drangendorff's reagent, acetic anhydride, 2, 2-diphenyl-1-picrylhydrazyl (DPPH), p-iodonitrotetrazolium violet, Methods: Antibacterial activity was evaluated using ...

Sulphur Extraction at Bryan Mound

Energy Technology Data Exchange (ETDEWEB)

Kirby, Carolyn L [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lord, Anna C. Snider [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-08-01

The Bryan Mound caprock was subjected to extens ive sulphur mining prior to the development of the Strategic Petroleum Reserve. Undoubtedl y, the mining has modified the caprock integrity. Cavern wells at Bryan Mound have been subject to a host of well integr ity concerns with many likely compromised by the cavernous capro ck, surrounding corrosive environment (H ₂ SO ₄ ), and associated elevated residual temperatures al l of which are a product of the mining activities. The intent of this study was to understand the sulphur mining process and how the mining has affected the stability of the caprock and how the compromised caprock has influenced the integrity of the cavern wells. After an extensiv e search to collect pert inent information through state agencies, literature sear ches, and the Sandia SPR librar y, a better understanding of the caprock can be inferred from the knowledge gaine d. Specifically, the discovery of the original ore reserve map goes a long way towards modeling caprock stability. In addition the gained knowledge of sulphur mining - subs idence, superheated corrosive wa ters, and caprock collapse - helps to better predict the post mi ning effects on wellbore integrity. This page intentionally left blank

Sulphur isotope measurements on sulphates from Antarctic atmospheric precipitations, lake waters and salt efflorescences: a contribution to the study of the natural sulphur cycle

International Nuclear Information System (INIS)

Wand, U.; Maass, I.; Haendel, D.

1987-01-01

Sulphur isotope analyses are an important tool for the study of the natural sulphur cycle. However, on the northern hemisphere such studies particularly of the atmospheric component of the cycle are seriously hampered and in many regions practically impossible because of the high emission rate of anthropogenic sulphur. Only in remote areas of the world such as the Antarctic 34 S analyses can be used with success to identify the various natural sulphur sources (marine, biogenic and volcanic sources). We report here preliminary results of 34 S isotope measurements on sulphates from recent atmospheric precipitations (snow), lake waters and salt efflorescences sampled in the Schirmacher Oasis and the Wohlthat Massif, central Queen Maud Land, East Antarctica. Except for 4 efflorescence samples the sulphates investigated in this work are enriched in 34 S relative to the meteoritic sulphur standard (CDT). On an average the sulphates of our study area are isotopically lighter than those from the McMurdo region, South Victoria land. The latter region is characterized by the predominance of salts of marine origin. (author)

Extraction of uranium from phosphoric-hydrobromic acid mixture by N-lauryl tri alkyl methylamine

Energy Technology Data Exchange (ETDEWEB)

Guirguis, L A [Nuclear materials authority, Cairo, (Egypt); Tadros, N A [Hot laboratories center, atomic energy authority, Cairo, (Egypt)

1995-10-01

A uranium recovery process from phosphoric acid produced by the dihydrate method was elaborated. Decomposition of phosphate rock containing 0.02% U is carried out with sulphuric acid. Crude phosphoric acid is filtered off, steam concentrated to 45% P{sub 2} O{sub 5} (6.27 M) and then clarified with activated clay and carbon. The clear phosphoric acid is introduced to uranium extraction after the addition of 0.88 M hydrobromic acid by 0.134 M amberlite LA.2 and 5% decanol, as a modifier, in kerosene. While 10% ammonium sulphate solution is used for stripping. Over 90% uranium recovery is obtained. 6 figs., 1 tab.

21 CFR 146.148 - Reduced acid frozen concentrated orange juice.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Reduced acid frozen concentrated orange juice. 146... Canned Fruit Juices and Beverages § 146.148 Reduced acid frozen concentrated orange juice. (a) Reduced acid frozen concentrated orange juice is the food that complies with the requirements for composition...

Selective methods for polyphenols and sulphur dioxide determination in wines.

Science.gov (United States)

García-Guzmán, Juan J; Hernández-Artiga, María P; Palacios-Ponce de León, Lourdes; Bellido-Milla, Dolores

2015-09-01

A critical review to the methods recommended by international bodies and widely used in the winery industry and research studies was performed. A Laccase biosensor was applied to the selective determination of polyphenols in wines. The biosensor response was characterised and it responds mainly to o-diphenols which are the principal polyphenols responsible for the stability and sensory qualities of wines. The spectrophotometric method to determine free and total sulphur dioxide recommended for beers was applied directly to wines. A sampling of 14 red and white wines was performed and they were analysed for biosensor polyphenol index (IBP) and sulphur dioxide concentration (SO2). The antioxidant capacity by the ABTS(+) spectrophotometric method was also determined. A correlation study was performed to elucidate the influence of the polyphenols and SO2 on the wines stability. High correlations were found between IBP and antioxidant capacity and low correlation between SO2 and antioxidant capacity. To evaluate the benefits of wine drinking a new parameter (IBP/SO2) is proposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Combined experimental and numerical kinetic characterization of NR vulcanized with sulphur, N terbutyl, 2 benzothiazylsulphenamide and N,N diphenyl guanidine

Energy Technology Data Exchange (ETDEWEB)

Milani, G., E-mail: gabriele.milani@polimi.it [Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milan (Italy); Hanel, T.; Donetti, R. [Pirelli Tyre, Via Alberto e Piero Pirelli 25, 20126 Milan (Italy); Milani, F. [Chem. Co, Via J.F.Kennedy 2, 45030 Occhiobello (Italy)

2016-06-08

The paper presents the final results of a comprehensive experimental and numerical analysis aimed at deeply investigating the behavior of Natural Rubber (NR) vulcanized with sulphur in presence of different accelerators during standard rheometer tests. NR in presence of sulphur and two different accelerators (DPG and TBBS) in various concentrations is investigated, changing the curing temperature in the range 150-180°C and obtaining rheometer curves with a step of 10°C. Sulphur-TBBS concentrations considered are 1-1, 1-3, 3-3 and 3-1, with DPG at 1-4 phr respectively. A total of 48 experimental rheometer curves is so obtained. To fit experimental data, the general reaction scheme proposed by Han and co-workers for vulcanized sulphur NR is re-adapted and suitably modified taking into account the single contributions of the different accelerators. Chain reactions initiated by the formation of macro-compounds responsible for the formation of the unmatured crosslinked polymer are accounted for. In presence of two accelerators, reactions are assumed to proceed in parallel, making the practically effective hypothesis that there is no interaction between the two accelerators. From the simplified kinetic scheme adopted, a closed form solution is found for the crosslink density, with the only limitation that the induction period is excluded from computations. For each experimented case on the same blend, reaction kinetic constants provided by the model are utilized to deduce their trend in the Arrhenius space, also outside the temperature range inspected. Rather close linearity is found in the majority of the cases. A comparative analysis is carefully conducted among the constants at the different concentrations of S, TBBS and DPG investigated, allowing a prediction of curing behavior at any vulcanization temperature and with concentrations not experimentally tested, without the need of addition costly experimentation.

Combined experimental and numerical kinetic characterization of NR vulcanized with sulphur, N terbutyl, 2 benzothiazylsulphenamide and N,N diphenyl guanidine

International Nuclear Information System (INIS)

Milani, G.; Hanel, T.; Donetti, R.; Milani, F.

2016-01-01

The paper presents the final results of a comprehensive experimental and numerical analysis aimed at deeply investigating the behavior of Natural Rubber (NR) vulcanized with sulphur in presence of different accelerators during standard rheometer tests. NR in presence of sulphur and two different accelerators (DPG and TBBS) in various concentrations is investigated, changing the curing temperature in the range 150-180°C and obtaining rheometer curves with a step of 10°C. Sulphur-TBBS concentrations considered are 1-1, 1-3, 3-3 and 3-1, with DPG at 1-4 phr respectively. A total of 48 experimental rheometer curves is so obtained. To fit experimental data, the general reaction scheme proposed by Han and co-workers for vulcanized sulphur NR is re-adapted and suitably modified taking into account the single contributions of the different accelerators. Chain reactions initiated by the formation of macro-compounds responsible for the formation of the unmatured crosslinked polymer are accounted for. In presence of two accelerators, reactions are assumed to proceed in parallel, making the practically effective hypothesis that there is no interaction between the two accelerators. From the simplified kinetic scheme adopted, a closed form solution is found for the crosslink density, with the only limitation that the induction period is excluded from computations. For each experimented case on the same blend, reaction kinetic constants provided by the model are utilized to deduce their trend in the Arrhenius space, also outside the temperature range inspected. Rather close linearity is found in the majority of the cases. A comparative analysis is carefully conducted among the constants at the different concentrations of S, TBBS and DPG investigated, allowing a prediction of curing behavior at any vulcanization temperature and with concentrations not experimentally tested, without the need of addition costly experimentation.

Effect of vermicomposting on calcium, sulphur and some heavy metal content of different biodegradable organic wastes under liming and microbial inoculation.

Science.gov (United States)

Das, Debabrata; Bhattacharyya, Pradip; Ghosh, B C; Banik, Pabitra

2012-01-01

A study was conducted to evaluate the changes in total calcium and sulphur and some heavy metal (Zn, Cu, and Pb) concentration of different organic wastes affected by liming and microorganism inoculation. Vermicomposting was an effective technology for disposal of organic substrates like municipal solid wastes (MSW), possessing comparatively higher concentration of heavy metals. The addition of lime in initial organic substrates significantly (P ≤ 0.05) increased total calcium and total sulphur content of vermicomposts. Inoculation of microorganisms significantly (P ≤ 0.05) reduced the heavy metal content of final products as compared to control. Fungal strains were comparatively more effective in detoxification of heavy metals than B. polymyxa.

Being green on sulphur: Targets, measures and side-effects

DEFF Research Database (Denmark)

Kontovas, Christos A.; Panagakos, George; Psaraftis, Harilaos N.

2016-01-01

to sea to reduce congestion, and might ultimately (under certain circumstances) increase the overall level of CO2 emissions along the entire supply chain. The purpose of this chapter is to investigate the potential effect of sulphur regulations on the share of cargo transported by the waterborne mode vis......Green House Gas (GHG) emissions are not the only emissions of concern to the international transport community. SOx emissions are non-GHG emissions that are caused by the presence of sulphur in the fuel. As the maximum percentage of sulphur in automotive and aviation fuels is strictly regulated...

Distribution and isotopic abundance of sulphur in recent marine sediments off southern California

Energy Technology Data Exchange (ETDEWEB)

Kaplan, I R; Emergy, K O; Rittenberg, S C

1963-01-01

Analyses of sulphur compounds in basin sediments off southern California indicate that elemental sulphur, free sulphide, hydrotroilite, organic sulphur, sulphate and pyrite are present in quantities that vary with environment and depth in the sediments. Pyrite is generally the most abundant form, occurring in oxidizing as well as in reducing sediments and often constituting 90% of total sulphur. A material balance indicates that the total sulphur content is far in excess of the sulphate-sulphur initially trapped in the interstitial water. This evidence, together with failure to detect significant alternate sources, suggests that sulphate-sulphur is extracted from the overlying sea water at the sediment-water interface. Isotope measurements confirm many of the conclusions suggested by the quantitative chemical analyses. The show that biological sulphate reduction is the single most important process in the sulphur cycle. The sulphide released is converted to hydrotrolite and then to pyrite. Elemental and organic sulphur appear to be continually forming and reacting in the sediment column. The organic sulphur released from decaying organic matter apparently plays only a small role in the sulphur economy. Enrichment in S/sup 32/ ranging from 9 to 62% was measured in pyrite fragments, a spread similar to that previously observed in ancient sediments. Data from field and laboratory experiments were combined to determine rate of sulphate reduction, number of sulphate reducing bacteria and the amount of organic matter decomposed during sulphate reduction in the sediment, as well as rate of renewal of water in the basins. The results suggest that the methods used may have many applications for elucidating in situ rate processes.

Occurrence and Determination of Haloacetic Acids in Metro Manila Drinking Water

Directory of Open Access Journals (Sweden)

Irene B. Rodriguez

2009-12-01

Full Text Available Haloacetic acids are found in chlorinated water with high organic matter content. An analytical method based on a US EPA method for measuring these compounds in water is described. The optimized method used diethyl ether as extraction solvent with sulphuric acid-methanol as esterification agent and subsequent detection by gas chromatography-electron capture detection. Evaluation of this method showed that it was linear in the concentration range of 10 to 150 µg L-1 and the method detection limits were from 17 to 57 µg L-1. Although the method demonstrated low recoveries (16 to 43%, it is useful in the quantitative determination of monochloroacetic acid as well as the qualitative determination of other haloacetic acids in water. Drinking water samples taken from different areas in Metro Manila serviced by the local treatment plants were analysed using the method. Monochloroacetic acid, monobromoacetic acid, and bromochloroacetic acid were detected in these samples. Monochloroacetic acid was quantified and found in concentrations ranging from 19 to 157 µg L-1. In most of the water samples, the concentration of monochloroacetic acid exceeded the US EPA maximum allowable total concentration of 60 µg L-1 for the five haloacetic acids (monochloro-, dichloro-, trichloro-, monobromo-, and dibromoacetic acids in drinking water. This initial study established the occurrence of potentially harmful haloacetic acids in the local drinking water supplies.

The X-ray fluorescent method for determination of total sulphur in bituminous coals

International Nuclear Information System (INIS)

Widowska-Kusmierska, J.; Siess, K.

1979-01-01

The X-ray fluorescent technique for the determination of total sulphur covering concentrations from 0,1 to 10% has been applied for bituminous coals showing a great variability in qualitative and quantitative composition of mineral matter (ash). The described method is a quick one giving results during one hour. The obtained good accuracy of determinations gives prospects for wide industrial application. (author)

Pyrotechnic countermeasures: IV. Radiometric performance of a sulphur-based Flare composition

Energy Technology Data Exchange (ETDEWEB)

Koch, Ernst-Christian [NATO Munitions Safety Information Analysis Center (MSIAC), Brussels (Belgium)

2008-10-15

Radiometric performance of a sulphur-based flare composition has been investigated. Composition comprising sulphur, potassium perchlorate and antimony sulphide has acceptable band ratio but an order of magnitude weaker spectral efficiency than typical carbon-based compositions. The use of other sulphur compounds with potential for increased performance is discussed. For part III see Ref. [1]. (Abstract Copyright [2008], Wiley Periodicals, Inc.)

Sulphur XANES Analysis of Cultured Human Prostate Cancer Cells

International Nuclear Information System (INIS)

Kwiatek, W.M.; Podgorczyk, M.; Paluszkiewicz, Cz.; Balerna, A.; Kisiel, A.

2008-01-01

Prostate cancer is one of the most commonly diagnosed cancers in men throughout the world. It is believed that changes to the structure of protein binding sites, altering its metabolism, may play an important role in carcinogenesis. Sulphur, often present in binding sites, can influence such changes through its chemical speciation. Hence there is a need for precise investigation of coordination environment of sulphur. X-ray absorption near edge structure spectroscopy offers such possibility. Cell culture samples offer histologically well defined areas of good homogeneity, suitable for successful and reliable X-ray absorption near edge structure analysis. This paper presents sulphur speciation data collected from three different human prostate cancer cell lines (PC-3, LNCaP and DU-145). Sulphur X-ray absorption near edge structure analysis was performed on K-edge structure. The spectra of cells were compared with those of cancerous tissue and with organic substances as well as inorganic compounds. (authors)

Accidental sulphuric acid poisoning in a newborn

African Journals Online (AJOL)

2015-05-18

May 18, 2015 ... CASE REPORT. Niger J Paed 2015; 42 (3):237 –240. Abdulkadir I. Hassan L. Abdullahi F. Akeredolu FD. Purdue S. Okpe M. Sobowale AM. Adewumi OA. Abdullahi U. Onadiran ... Recommended management protocols include resting the esophagus or the ... of acid 5 hours prior to presentation. The acid ...

Fluence of dielectric constant (D), (H/sup +/) and (SO/sub 4/sup -2/) on the rate of redox reaction between tris (2,2-bipyridine) iron (II) and ceric sulphate in aqueous sulphuric acid medium

International Nuclear Information System (INIS)

Khattak, R.; Naqvi, I.I.; Farrukh, M.A.

2007-01-01

Kinetic of the redox reaction between tris (2,2-bipyridine)iron(II) cation and ceric sulphate has been studied in aqueous sulphuric acid medium. Different methods were employed for the determination of order of reaction. The order of reaction is found to be first with respect to reductant however retarding effect of increasing initial concentration of oxidant is found. Influence of (H/sup +/), (SO/sub 4/sup 2-) and dielectric constant (D) on the rate of redox reaction has also been studied. Increase in (H/sup +/) and dielectric constant of the medium retard the rate while enhancement of the (SO/sub 4/sup 2-/) accelerates the rate first and then the reaction goes towards retardation. Effects of (H/sup +/) and (SO/sub 4/sup 2-/) were studied by using acetic acid-sodium acetate buffer for the first one and varying ionic concentrations of the salt sodium sulphate for the latter one, whereas dielectric constant was varied by using 0%, 10% and 20% ethanol-water mixtures. Results of effects of each one of the factors i.e., H/sup +/, SO/sub 4/sup 2-/ and dielectric constant (D) have been compared and on the basis of these factors, (Ce(SO/sub 4/ )/sub 3/)/sup 2-/ is suggested to be the active species of cerium(IV). However a rate law consistent with the observed kinetic data has also been derived supporting the proposed mechanism. (author)

Characterization of selectively etched halloysite nanotubes by acid treatment

Science.gov (United States)

Garcia-Garcia, Daniel; Ferri, Jose M.; Ripoll, Laura; Hidalgo, Montserrat; Lopez-Martinez, Juan; Balart, Rafael

2017-11-01

Halloysite nanotubes (HNTs) are a type of naturally occurring inorganic nanotubes that are characterized by a different composition between their external and internal walls. The internal walls are mainly composed of alumina whilst external walls are composed of silica. This particular structure offers a dual surface chemistry that allows different selective surface treatments which can be focused on increasing the lumen, increasing porosity, etc. In this work, HNTs were chemically treated with different acids (sulphuric, acetic and acrylic acid), for 72 h at a constant temperature of 50 °C. As per the obtained results, the treatment with sulphuric acid is highly aggressive and the particular shape of HNTs is almost lost, with a remarkable increase in porosity. The BET surface area increases from 52.9 (untreated HNTs) up to 132.4 m2 g-1 with sulphuric acid treatment, thus showing an interesting potential in the field of catalysis. On the other hand, the treatment with acetic acid led to milder effects with a noticeable increase in the lumen diameter that changed from 13.8 nm (untreated HNTs) up to 18.4 nm which the subsequent increase in the loading capacity by 77.8%. The aluminium content was measured by X-ray fluorescence (XRF) and laser induced breakdown spectroscopy (LIBS). The final results using two systems, suggest a good correlation between the acid strength and the aluminium reduction. Consequently, is possible to conclude that new applications for HNTs can be derived from selective etching with acids. Sulphuric acid widens the potential of HNTs in the field of catalysis while weak acids such as acetic and acrylic acids give a controlled and homogeneous lumen increase with the corresponding increase in the loading capacity.

Comparison of the effect of gamma irradiation, heat-radiation combination, and sulphur dioxide generating pads on decay and quality of grapes

International Nuclear Information System (INIS)

Thomas, Paul; Brij Bhushan; Joshi, M.R.

1995-01-01

Effect of gamma irradiation, heat-radiation combination and in-package sulphur dioxide fumigation on fungal decay, and quality of seedless grape cultivars, Thompson, Sonaka and Tas-A-Ganesh was evaluated under different storage regimes. Irradiation at 2 kGy or a combination of hot water dip (50 degC, 5 min), plus irradiation (1 kGy) showed less spoilage due to Rhizopus spp. and Botrytis spp. in grapes packaged in tissue paper lined boxes and stored at 4 deg, 15 deg and 25 degC. Storage in polyethylene lined boxes increased the fungal rot. In-package sulphur dioxide generating pad was most effective for control of decay in polyethylene lined boxes stored at 10 deg and 20 degC, but caused berry bleaching. Irradiation at 2.5 or 3.5 kGy controlled decay at 10 degC, but not so effectively at 20 degC. Organoleptic quality, berry firmness, and soluble solids were not affected by irradiation, but decreases in titratable acids and ascorbic acid were recorded. Packaging in polyethylene lined boxes retained berry turgidity, while slight shrivelling occurred in tissue paper lined boxes. The results indicate that gamma irradiation has potential as an alternative to sulphur dioxide fumigation for decay control during shipping and storage. (author). 20 refs., 4 tabs

Soybean epoxide production with in situ peracetic acid using homogeneous catalysis

Directory of Open Access Journals (Sweden)

Luis Alejandro Boyacá Mendivelso

2010-01-01

Full Text Available Using vegetable oils has become an excellent option for petrochemical product substitution. The epoxides obtained from such oils have wide applications as plastifiers and PVC stabilisers and as raw material in polyol synthesis for the polyurethane industry. This paper presents soybean oil epoxidation using a homogeneous catalyst in a well-mixed, stirred reactor being operated in iso- thermal conditions. The best result achieved was a 6.4% oxyrane oxygen content using hydrogen peroxide (25% molar excess, a- cetic acid (5% p/p and sulphuric acid (2% p/p concentrations at 80°C.

Cadmium Alters the Concentration of Fatty Acids in THP-1 Macrophages.

Science.gov (United States)

Olszowski, Tomasz; Gutowska, Izabela; Baranowska-Bosiacka, Irena; Łukomska, Agnieszka; Drozd, Arleta; Chlubek, Dariusz

2018-03-01

Fatty acid composition of human immune cells influences their function. The aim of this study was to evaluate the effects of known toxicant and immunomodulator, cadmium, at low concentrations on levels of selected fatty acids (FAs) in THP-1 macrophages. The differentiation of THP-1 monocytes into macrophages was achieved by administration of phorbol myristate acetate. Macrophages were incubated with various cadmium chloride (CdCl 2 ) solutions for 48 h at final concentrations of 5 nM, 20 nM, 200 nM, and 2 μM CdCl 2 . Fatty acids were extracted from samples according to the Folch method. The fatty acid levels were determined using gas chromatography. The following fatty acids were analyzed: long-chain saturated fatty acids (SFAs) palmitic acid and stearic acid, very long-chain saturated fatty acid (VLSFA) arachidic acid, monounsaturated fatty acids (MUFAs) palmitoleic acid, oleic acid and vaccenic acid, and n-6 polyunsaturated fatty acids (PUFAs) linoleic acid and arachidonic acid. Treatment of macrophages with very low concentrations of cadmium (5-200 nM) resulted in significant reduction in the levels of arachidic, palmitoleic, oleic, vaccenic, and linoleic acids and significant increase in arachidonic acid levels (following exposure to 5 nM Cd), without significant reduction of palmitic and stearic acid levels. Treatment of macrophages with the highest tested cadmium concentration (2 μM) produced significant reduction in the levels of all examined FAs: SFAs, VLSFA, MUFAs, and PUFAs. In conclusion, cadmium at tested concentrations caused significant alterations in THP-1 macrophage fatty acid levels, disrupting their composition, which might dysregulate fatty acid/lipid metabolism thus affecting macrophage behavior and inflammatory state.

Efficacy and phytotoicity of lime sulphur in organic apple production

NARCIS (Netherlands)

Holb, I.J.; Jong, de P.F.; Heijne, B.

2003-01-01

Curative and preventive efficacy and phytotoxicity of lime sulphur spray schedules, based on a warning system, were evaluated in the Netherlands during two growing seasons under field conditions. In most cases, lime sulphur treatments applied either curatively or preventively resulted in

The role of acid anion on the inhibition of the acidic corrosion of steel by lupine extract

Energy Technology Data Exchange (ETDEWEB)

Abdel-Gaber, A.M. [Chemistry Department, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt)], E-mail: ashrafmoustafa@yahoo.com; Abd-El-Nabey, B.A.; Saadawy, M. [Chemistry Department, Faculty of Science, Alexandria University, Ibrahimia, P.O. Box 426, Alexandria 21321 (Egypt)

2009-05-15

The inhibitive effect of lupine (Lupinous albus L.) extract on the corrosion of steel in aqueous solution of 1 M sulphuric and 2 M hydrochloric acids was investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Potentiodynamic polarization curves indicated that the lupine extract acts as a mixed-type inhibitor. EIS measurements showed that the dissolution process is under activation control. The inhibition efficiency of the extract obtained from impedance and polarization measurements was in a good agreement and was found to increase with increasing concentration of the extract. The obtained results showed that, the lupine extract could serve as an effective inhibitor for the corrosion of steel in acid media and the extract was more effective in case of hydrochloric acid. Theoretical fitting of the corrosion data to the kinetic-thermodynamic model was tested to show the nature of adsorption.

The implications of the new sulphur limits on the European Ro-Ro sector

DEFF Research Database (Denmark)

Zis, Thalis; Psaraftis, Harilaos N.

-based alternatives. The exact repercussions of the new sulphur limits are difficult to identify in the wake of significant recent reductions of the fuel prices for both low-sulphur and heavy fuel oil. This paper presents a modal split model that estimates modal shifts vis-a-vis competing maritime and land......In an effort to reduce the environmental impacts of maritime transportation, the International Maritime Organization (IMO) designated special Sulphur Emission ControlAreas (SECAs) where ships are required to use low-sulphur fuel. In January 2015, the sulphur limit within SECAs was lowered to 0.......1%, which can only be achieved if vessels are using pricier ultra-low sulphur fuel, or invest in abatement technologies. The increased operating costs borne by Ro-Ro operators in SECAs due to the stricter limits can result in the shutting down of some routes and a redistribution of cargo flows with land...

Sulphur-oxidising and Sulphate-reducing Communities in Brazilian Mangrove Sediments

NARCIS (Netherlands)

Varon-Lopez, Maryeimy; Dias, A.C.F; Fasanella, C.C.; Durrer, A.; Melo, I.S.; Kuramae, E.E.; Andreote, F.D.

2014-01-01

Mangrove soils are anaerobic environments rich in sulphate and organic matter. Although the sulphur cycle is one of the major actors in this ecosystem, little is known regarding the sulphur bacteria communities in mangrove soils. We investigated the abundance, composition and diversity of

Simultaneous Determination of Sulphur metabolites in Arabidopsis thaliana via LC-ESI-MS/MS and 34S-metabolic Labelling

NARCIS (Netherlands)

Hsieh, Chin-Lin; Yeh, Kai-Wun; De Kok, Luit J.; Pan, Ryh-Nan; Kuo, Yueh-Hsiung; Tseng, Mei-Hwei

2012-01-01

Introduction Sulphur-containing metabolites play an important role in metabolism and homeostasis. Determination of these metabolites is challenging owing to their low concentrations and the interference in mass spectrometry analysis. Objective To develop a sensitive and accurate method based on

Effect of Hydrochloric Acid Concentration on the Conversion of Sugarcane Bagasse to Levulinic Acid

Science.gov (United States)

Anggorowati, Heni; Jamilatun, Siti; Cahyono, Rochim B.; Budiman, Arief

2018-01-01

Levulinic acid is a new green platform chemical used to the synthesis of a variety of materials for numerous applications such as fuel additives, polymers and resins. It can be produced using renewable resources such as biomass like sugarcane bagasse which are cheap and widely available as waste in Indonesia. In this study, sugarcane bagasse was hydrolyzed using hydrochloric acid with a solid liquid ratio 1:10. The effects of hydrochloric acid concentration at temperature of 180 °C and reaction time of 30 min were studied. The presence of levulinic acid in product of hydrolysis was measured with gas chromatography (GC). It was found that the highest concentration of levulinic acid was obtained at 1 M hydrochloric acid in 25.56 yield%.

Interaction of magnesium diboride with HΛ2O, HΛ2OΛ2 and with acids

International Nuclear Information System (INIS)

Lyashenko, V.I.; Kosolapova, T.Ya.; Serebryakova, T.I.

1985-01-01

Chemical stability of magnesium diboride in some agressive media is investigated. It is shown that magnesium diboride possesses high chemical activity in relation to acids (nitric, phosphoric, hydrochloric, sulphuric). The fluohydric acid and hydrogen peroxide completely decompose magnesium boride. The kinetics of MgB 2 decomposition in aqueous solutions of acids (hydrochloric, sulphuric, nitric) and in water is studied. Activation energies and solubility rate constants are calculated

Maximum permissible continuous release rates of phosphorus-32 and sulphur-35 to atmosphere in a milk producing area

Energy Technology Data Exchange (ETDEWEB)

Bryant, P M

1963-01-01

A method is given for calculating, for design purposes, the maximum permissible continuous release rates of phosphorus-32 and sulphur-35 to atmosphere with respect to milk contamination. In the absence of authoritative advice from the Medical Research Council, provisional working levels for the concentration of phosphorus-32 and sulphur-35 in milk are derived, and details are given of the agricultural assumptions involved in the calculation of the relationship between the amount of the nuclide deposited on grassland and that to be found in milk. The agricultural and meteorological conditions assumed are applicable as an annual average to England and Wales. The results (in mc/day) for phosphorus-32 and sulphur-35 for a number of stack heights and distances are shown graphically; typical values, quoted in a table, include 20 mc/day of phosphorus-32 and 30 mc/day of sulfur-35 as the maximum permissible continuous release rates with respect to ground level releases at a distance of 200 metres from pastureland.

Analytical protocols for the determination of sulphur compounds characteristic of the metabolism of Chlorobium limicola

Directory of Open Access Journals (Sweden)

A. Aliboni

2015-09-01

Full Text Available Chlorobium limicola belongs to the green sulphur bacteria that has a potential for technological applications such as biogas clean up oxidising hydrogen sulphide to elemental sulphur through photosynthetic process. In the present work, analytical methods are described for the determination of different sulphur species in C. limicola cultures – sulphide by GC-FPD, sulphate by ionic HPLC and elemental sulphur by RP HPLC. The latter method eliminates the need for chloroform extraction of water suspensions of elemental sulphur. Data from sulphide and elemental sulphur analyses have been compared with ones coming from more traditional analytical methodologies.

Performance evaluation of high-sulphur coal-fired USC plant integrated with SNOX and CO2 capture sections

International Nuclear Information System (INIS)

Cau, Giorgio; Tola, Vittorio; Bassano, Claudia

2015-01-01

In recent years coal-fired power plants have increased their role in the global energy scenario thanks to reliability, security of fuel supply and lower cost of fuel and electricity. In this framework global warming issues require a sustainable use of coal and great efforts for greenhouse gases reduction, addressing research and development projects towards more efficient solutions in terms of efficiency and environmental impact. With this aim in this paper a performance assessment of an Ultra Super Critical (USC) steam plant integrated with a CO 2 removal section was carried out. The study is based on simulation models specifically developed through Aspen-Plus and Gate-Cycle software platforms. Performance was assessed referring to typical USC commercial size plants (400–600 MW), fuelled by a mix of a low-sulphur coal and a Sardinian (Sulcis) high-sulphur coal. The USC plant, based on a reheated and regenerative Rankine cycle, is integrated with an SNOX section, with integrated DeNO x and DeSO x processes, and a low temperature CO 2 capture section. The SNOX technology shows several advantages in comparison to conventional de-nitrification and de-sulphuration systems. In particular it is capable to remove both nitrogen and sulphur oxides, requiring less energy absorption compared to traditional FGD systems, allowing a further preheating of the combustion air and without producing process waste. Besides the SNOX releases a commercial product as the sulphuric acid (H 2 SO 4 ) and operational costs are reduced when sulphur content in the coal increases. The CO 2 capture system was based on a chemical absorption process. A conventional system based on an amine (monoethanolamine, MEA) aqueous solution was considered. In order to match high pressure and purity CO 2 transportation requirements, the CO 2 removal section is also integrated with a conditioning and compression section. A performance assessment of the USC plant was carried out varying the high-sulphur coal

Sulphur and lead isotopes in strata-bound deposits, ch. 8

International Nuclear Information System (INIS)

Sangster, D.F.

1976-01-01

The use of sulphur and lead isotopes as isotopic tracers in the study of ore deposits containing these elements is reviewed. A discussion of the general theory, including abundance and fractionation of sulphur isotopes, single-stage leads, and anomalous leads (two-stage) is given. Attention is paid to sulphur isotopes enclosed in deposits which are located in marine host rocks and in rocks of continental or near-continental origin, as well as in deposits of the conglomerate-U(-Au) type. The lead isotope content of volcanogenic massive sulphide deposits and carbonate-hosted lead-zinc deposits is discussed

New method of measuring lichen respiration: response of selected species to temperature, pH and sulphur dioxide

Energy Technology Data Exchange (ETDEWEB)

Baddeley, M S; Ferry, B W; Finegan, E J

1971-01-01

The respiration of selected lichens and their response to temperature, pH and sulphur dioxide concentration were investigated in aqueous solution using an oxygen electrode. Respiration rates increased to a maximum at 40/sup 0/ C although some individual species showed variations from this general pattern. The optimal pH for respiration was found to be 4.2 except in Hypogymnia physodes (3.2) and Ramalina fastigiata (5.2). Sulfur dioxide at concentrations similar to those likely to be encountered in heavily polluted areas in nature had marked inhibitory effects of the respiration rate of all species investigated but as these variations did not entirely correspond to the tolerances of the species in the field some other factors must also be involved in the sensitivity of lichens to sulphur dioxide pollution. The advantages of using an oxygen electrode rather than manometric or other techniques in studies on the respiration rate of lichens are discussed. 29 references, 3 figures, 2 tables.

Mesoporous titanium-manganese dioxide for sulphur mustard and soman decontamination

International Nuclear Information System (INIS)

Stengl, Vaclav; Bludska, Jana; Oplustil, Frantisek; Nemec, Tomas

2011-01-01

Highlights: → New nano-dispersive materials for warfare agents decontamination. → 95% decontamination activities for sulphur mustard. → New materials base on titanium and manganese oxides. -- Abstract: Titanium(IV)-manganese(IV) nano-dispersed oxides were prepared by a homogeneous hydrolysis of potassium permanganate and titanium(IV) oxo-sulphate with 2-chloroacetamide. Synthesised samples were characterised using Brunauer-Emmett-Teller (BET) surface area and Barrett-Joiner-Halenda porosity (BJH), X-ray diffraction (XRD), infrared spectroscopy (IR), and scanning electron microscopy (SEM). These oxides were taken for an experimental evaluation of their reactivity with sulphur mustard (HD or bis(2-chloroethyl)sulphide) and soman (GD or (3,3'-dimethylbutan-2-yl)-methylphosphonofluoridate). Mn 4+ content affects the decontamination activity; with increasing Mn 4+ content the activity increases for sulphur mustard and decreases for soman. The best decontamination activities for sulphur mustard and soman were observed for samples TiMn 3 7 with 18.6 wt.% Mn and TiMn 5 with 2.1 wt.% Mn, respectively.

Effects of acidic deposition on the erosion of carbonate stone - experimental results from the U. S. National Acid Precipitation Assessment Program (NAPAP)

Energy Technology Data Exchange (ETDEWEB)

Baedecker, P.A.; Reddy, M.M.; Reimann, K.J.; Sciammarella, C.A. (US Geological Survey, Reston, VA (USA))

1992-06-01

Test briquettes and slabs of freshly quarried limestone and marble have been exposed to the environment to quantify the incremental effects of wet and dry deposition of hydrogen ion, sulphur dioxide, and nitrogen oxides on stone erosion. Erosion due to grain loss did not seem to be influenced by rainfall acidity, but may be influenced by dry deposition of sulphur dioxide between rainfall events. Chemical analyses of the run-off solutions suggest that around 30% of erosion by dissolution can be attributed to the wet deposition of hydrogen ion and the dry deposition of sulphur dioxide and nitric acid between rain events. The remaining 70% of erosion by dissolution is accounted for by the solubility of carbonate stone in 'clean' rain. 17 refs., 4 figs., 7 tabs.

Selective separation of indium by iminodiacetic acid chelating resin

International Nuclear Information System (INIS)

Fortes, M.C.B.; Benedetto, J.S.; Martins, A.H.

2007-01-01

- Indium can be recovered by treating residues, flue dusts, slags, and metallic intermediates in zinc smelting. This paper investigates the adsorption characteristics of indium and iron on an iminodiacetic acid chelating resin, Amberlite R IRC748 (Rohm and Haas Co.-USA). High concentrations of iron are always present in the aqueous feed solution of indium recovery. In addition, the chemical behaviour of iron in adsorptive systems is similar to that of indium. The metal concentrations in the aqueous solution were based on typical indium sulfate leach liquor obtained from zinc hydrometallurgical processing in a Brazilian plant. The ionic adsorption experiments were carried out by the continuous column method. Amberlite R IRC748 resin had a high affinity for indium under acidic conditions. Indium ions adsorbed onto the polymeric resin were eluted with a 0.5 mol/dm 3 sulphuric acid solution passed through the resin bed in the column. 99.5% pure indium sulfate aqueous solution was obtained using the iminodiacetic acid chelating resin Amberlite R IRC748. (author)

Effect of Thiobacillus thioparus 1904 and sulphur addition on odour emission during aerobic composting.

Science.gov (United States)

Gu, Wenjie; Sun, Wen; Lu, Yusheng; Li, Xia; Xu, Peizhi; Xie, Kaizhi; Sun, Lili; Wu, Hangtao

2018-02-01

The effects of sulphur and Thiobacillus thioparus 1904 on odour emissions during composting were studied. Results indicated that the sulphur addition reduced the pH and decreased cumulative emission of ammonia and the nitrogen loss by 47.80% and 44.23%, respectively, but the amount of volatile sulphur compounds (VSCs) and the sulphur loss increased. The addition of T. thioparus 1904 effectively reduced the cumulative emissions of H 2 S, methyl sulphide, methanethiol, dimethyl disulphide and the sulphur loss by 33.24%, 81.24%, 32.70%, 54.22% and 54.24%, respectively. T. thioparus 1904 also limited the nitrogen loss. The combined application of sulphur and T. thioparus 1904 resulted in the greatest amount of nitrogen retention. The accumulation of ammonia emissions was reduced by 63.33%, and the nitrogen loss was reduced by 71.93%. The combined treatment did not increase the emission of VSCs. The application of sulphur and T. thioparus 1904 may help to control the odour of compost. Copyright © 2017. Published by Elsevier Ltd.

Optimization of digestion parameters for analysing the total sulphur of mine tailings by inductively coupled plasma optical emission spectrometry.

Science.gov (United States)

Alam, Raquibul; Shang, Julie Q; Cheng, Xiangrong

2012-05-01

The oxidation of sulphidic mine tailings and consequent acid generation poses challenges for the environment. Accurate and precise analysis of sulphur content is necessary for impact assessment and management of mine tailings. Here, the authors aim at developing a rapid and easy digestion procedure, which may analyse and measure the total amount of sulphur in mine tailings by using inductively coupled plasma. For evaluating effects of several variables, the researchers used a univariate (analysis of variance (ANOVA)) strategy and considered factors such as composition of the acid mixture, heating time, and refluxing device to optimize the performance. To do the experiment, the researchers have used two certified reference materials (KZK-1 and RTS-2) and samples of tailings from Musselwhite mine. ANOVA result shows that heating time is the most influencing factor on acid digestion of the reference materials whereas in case of a digestion of tailings sample, hydrochloric acid proved to be the most significant parameter. Satisfactory results between the measured and referenced values are found for all experiments. It is found that the aqua regia (1 ml HNO(3) + 3 ml HCl) digestion of 0.1 g of samples after only 40 min of heating at 95°C produced fast, safe, and accurate analytical results with a recovery of 97% for the selected reference materials.

Sulphur in the Sculptor dwarf spheroidal galaxy. Including NLTE corrections

NARCIS (Netherlands)

Skúladóttir, Á.; Andrievsky, S. M.; Tolstoy, E.; Hill, V.; Salvadori, S.; Korotin, S. A.; Pettini, M.

In Galactic halo stars, sulphur has been shown to behave like other α-elements, but until now, no comprehensive studies have been done on this element in stars of other galaxies. Here, we use high-resolution ESO VLT/FLAMES/GIRAFFE spectra to determine sulphur abundances for 85 stars in the Sculptor

Effects of Low Phytanic Acid-Concentrated DHA on Activated Microglial Cells: Comparison with a Standard Phytanic Acid-Concentrated DHA.

Science.gov (United States)

Ruiz-Roso, María Belén; Olivares-Álvaro, Elena; Quintela, José Carlos; Ballesteros, Sandra; Espinosa-Parrilla, Juan F; Ruiz-Roso, Baltasar; Lahera, Vicente; de Las Heras, Natalia; Martín-Fernández, Beatriz

2018-05-30

Docosahexaenoic acid (DHA, 22:6 n-3) is an essential omega-3 (ω-3) long chain polyunsaturated fatty acid of neuronal membranes involved in normal growth, development, and function. DHA has been proposed to reduce deleterious effects in neurodegenerative processes. Even though, some inconsistencies in findings from clinical and pre-clinical studies with DHA could be attributed to the presence of phytanic acid (PhA) in standard DHA treatments. Thus, the aim of our study was to analyze and compare the effects of a low PhA-concentrated DHA with a standard PhA-concentrated DHA under different neurotoxic conditions in BV-2 activated microglial cells. To this end, mouse microglial BV-2 cells were stimulated with either lipopolysaccharide (LPS) or hydrogen peroxide (H 2 O 2 ) and co-incubated with DHA 50 ppm of PhA (DHA (PhA:50)) or DHA 500 ppm of PhA (DHA (PhA:500)). Cell viability, superoxide anion (O 2 - ) production, Interleukin 6 (L-6), cyclooxygenase-2 (COX-2), inducible nitric oxide synthase (iNOS), glutathione peroxidase (GtPx), glutathione reductase (GtRd), Caspase-3, and the brain-derived neurotrophic factor (BDNF) protein expression were explored. Low PhA-concentrated DHA protected against LPS or H 2 O 2 -induced cell viability reduction in BV-2 activated cells and O 2 - production reduction compared to DHA (PhA:500). Low PhA-concentrated DHA also decreased COX-2, IL-6, iNOS, GtPx, GtRd, and SOD-1 protein expression when compared to DHA (PhA:500). Furthermore, low PhA-concentrated DHA increased BDNF protein expression in comparison to DHA (PhA:500). The study provides data supporting the beneficial effect of low PhA-concentrated DHA in neurotoxic injury when compared to a standard PhA-concentrated DHA in activated microglia.

Sulphur in the metal poor globular cluster NGC 6397

Science.gov (United States)

Koch, A.; Caffau, E.

2011-10-01

Sulphur (S) is a non-refractory α-element that is not locked into dust grains in the interstellar medium. Thus no correction to the measured, interstellar sulphur abundance is needed and it can be readily compared to the S content in stellar photospheres. Here we present the first measurement of sulphur in the metal poor globular cluster (GC) NGC 6397, as detected in a MIKE/Magellan high signal-to-noise, high-resolution spectrum of one red giant star. While abundance ratios of sulphur are available for a larger number of Galactic stars down to an [Fe/H] of ~ -3.5 dex, no measurements in globular clusters more metal poor than -1.5 dex have been reported so far. We find aNLTE, 3-D abundance ratio of [S/Fe] = +0.52 ± 0.20 (stat.) ± 0.08 (sys.), based on theS I, Multiplet 1 line at 9212.8 Å. This value is consistent with a Galactic halo plateau as typical of other α-elements in GCs and field stars, but we cannot rule out its membership with a second branch of increasing [S/Fe] with decreasing [Fe/H], claimed in the literature, which leads to a large scatter at metallicities around - 2 dex. The [S/Mg] and [S/Ca] ratios in this star are compatible with a Solar value to within the (large) uncertainties. Despite the very large scatter in these ratios across Galactic stars between literature samples, this indicates that sulphur traces the chemical imprints of the other α-elements in metal poor GCs. Combined with its moderate sodium abundance ([S/Na]NLTE = 0.48), the [S/Fe] ratio in this GC extends a global, positive S-Na correlation that is not seen in field stars and might indicate that proton-capture reactions contributed to the production of sulphur in the (metal poor) early GC environments. This paper includes data gathered with the 6.5 m Magellan Telescopes located at Las Campanas Observatory, Chile.

Ultrasound-assisted extraction for total sulphur measurement in mine tailings

International Nuclear Information System (INIS)

Khan, Adnan Hossain; Shang, Julie Q.; Alam, Raquibul

2012-01-01

Highlights: ► We develop a total sulphur measuring procedure of mine tailings. ► Ultrasound is used in the sample pre-treatment process. ► Full factorial design is applied to identify the best level of effecting factors. - Abstract: A sample preparation method for percentage recovery of total sulphur (%S) in reactive mine tailings based on ultrasound-assisted digestion (USAD) and inductively coupled plasma-optical emission spectroscopy (ICP-OES) was developed. The influence of various methodological factors was screened by employing a two-level and three-factor (2 3 ) full factorial design and using KZK-1, a sericite schist certified reference material (CRM), to find the optimal combination of studied factors and %S. Factors such as the sonication time, temperature and acid combination were studied, with the best result identified as 20 min of sonication, 80 °C temperature and 1 ml of HNO 3 :1 ml of HCl, which can achieve 100% recovery for the selected CRM. Subsequently a fraction of the 2 3 full factorial design was applied to mine tailings. The percentage relative standard deviation (%RSD) for the ultrasound method is less than 3.0% for CRM and less than 6% for the mine tailings. The investigated method was verified by X-ray diffraction analysis. The USAD method compared favorably with existing methods such as hot plate assisted digestion method, X-ray fluorescence and LECO™-CNS method.

First prokaryotic biodiversity assessment using molecular techniques of an acidic river in Neuquén, Argentina.

Science.gov (United States)

Urbieta, M Sofía; González Toril, E; Aguilera, A; Giaveno, M Alejandra; Donati, E

2012-07-01

Two acidic hot springs close to the crater of Copahue Volcano (Neuquén, Argentina) are the source of the Río Agrio. The river runs several kilometres before flowing into Caviahue Lake. Along the river, temperature, iron, other metal and proton concentrations decrease gradually with distance downstream. From the source to the lake and depending on the season, pH can rise from 1.0 (or even less) to about 4.0, while temperature values decrease from 70°C to 15°C. Water samples were taken from different stations on the river selected according to their physicochemical parameters. In order to assess prokaryotic biodiversity throughout the water column, different and complementary molecular biology techniques were used, mainly in situ hybridisation and 16S rRNA gene cloning and sequencing. All microorganisms found are typical of acidic environments. Sulphur-oxidizing bacteria like Acidithiobacillus thiooxidans and Acidithiobacillus albertensis were detected in every station. Moderately thermophile iron- and sulphur-oxidizing bacteria like members of Alicyclobacillus and Sulfobacillus genera were also ubiquitous. Strict iron-oxidizing bacteria like Leptospirillum and Ferrimicrobium were present at the source of the river, but disappeared downstream where iron concentrations were much lower. Iron-oxidizing, mesophilic Ferroplasma spp. were the main archaea found. The data presented in this work represent the first molecular assessment of this rare natural acidic environment.

Sulphur loading of respirable and inhalable dust at a platinum smelter / Swanepoel J.D.

OpenAIRE

Swanepoel, Johannes Deon.

2012-01-01

The contribution that sulphur, in the form of sulphates, has on ill health is still a focal point of many a study, especially in environmental studies depicting the effects that particulate air pollution has on health. Although the implication of sulphur on particulate matter is not yet well defined, numerous studies do state that the presence of sulphur on particulate matter contributes to poor health. Sulphur adhered to dust has been associated with cardiovascular mortality and the ability ...

Valorisation of waste ilmenite mud in the manufacture of sulphur polymer cement.

Science.gov (United States)

Contreras, Manuel; Gázquez, Manuel Jesús; García-Díaz, Irene; Alguacil, Francisco J; López, Félix A; Bolívar, Juan Pedro

2013-10-15

This paper reports the preparation of sulphur polymer cements (SPCs) incorporating waste ilmenite mud for use in concrete construction works. The ilmenite mud raw material and the mud-containing SPCs (IMC-SPCs) were characterised physico-chemically and radiologically. The optimal IMC-SPC mixture had a sulphur/mud ratio (w/w) of 1.05 (mud dose 20 wt%); this cement showed the greatest compressive strength (64 MPa) and the lowest water absorption coefficient (0.4 g cm(-2) at 28 days). Since ilmenite mud is enriched in natural radionuclides, such as radium isotopes (2.0·10(3) Bq kg(-1)(228)Ra and 5.0·10(2) Bq kg(-1)(226)Ra), the IMC-SPCs were subjected to leaching experiments, which showed their environmental impact to be negligible. The activity concentration indices for the different radionuclides in the IMC-SPCs containing 10% and 20% ilmenite mud met the demands of international standards for materials used in the construction of non-residential buildings. Copyright © 2013 Elsevier Ltd. All rights reserved.

Muonium states and dynamics in phosphorus and sulphur

International Nuclear Information System (INIS)

Cox, S.F.J.; Cottrell, S.P.; Hopkins, G.A.; Kay, M.; Pratt, F.L.

1997-01-01

The various states formed by positive muons implanted into phosphorus and sulphur have been characterized as a model for interstitial hydrogen, of which little is known in these elements. Repolarization studies reveal muonium-like states in each case, giving estimates of the hyperfine parameters and, for sulphur at least, an indication of the coexistence of a molecular radical state. The longitudinal-field relaxation functions suggest conversion of the paramagnetic states to diamagnetic, i.e. ionization or chemical reaction, in competition with strong spin-lattice relaxation

Inhibitory effect of non-ionic surfactants of the TRITON-X series on the corrosion of carbon steel in sulphuric acid

International Nuclear Information System (INIS)

Fuchs-Godec, R.

2007-01-01

The corrosion inhibition characteristics of non-ionic surfactants of the TRITON-X series, known as TRITON-X-100 and TRITON-X-405, on stainless steel (SS) type X4Cr13 in sulphuric acid were investigated by potentiodynamic polarisation measurements. It was found that these surfactants act as good inhibitors of the corrosion of stainless steel in 2 mol L -1 H 2 SO 4 solution, but the inhibition efficiency strongly depends on the electrode potential. The polarisation data showed that the non-ionic surfactants used in this study acted as mixed-type inhibitors and adsorb on the stainless steel surface, in agreement with the Flory-Huggins adsorption isotherm. Calculated ΔG ads values are -57.79 kJ mol -1 for TRITON-X-100, and -87.5 kJ mol -1 for TRITON-X-405. From the molecular structure it can be supposed that these surfactants adsorb on the metal surface through two lone pairs of electrons on the oxygen atoms of the hydrophilic head group, suggesting a chemisorption mechanism

Comparative study on sulphur reduction from heavy petroleum - Solvent extraction and microwave irradiation approach

Energy Technology Data Exchange (ETDEWEB)

Mohammed, Abdullahi Dyadya; Isah, Abubakar Garba; Umaru, Musa; Ahmed, Shehu [Department of Chemical Engineering, Federal University of Technology, P.M.B 65, Minna (Nigeria); Abdullahi, Yababa Nma [National Petroleum Investment Management Services (Nigeria National Petroleum Corporation), Lagos (Nigeria)

2012-07-01

Sulphur- containing compounds in heavy crude oils are undesirable in refining process as they affect the quality of the final product, cause catalyst poisoning and deactivation in catalytic converters as well as causing corrosion problems in oil pipelines, pumps and refining equipment aside environmental pollution from their combustion and high processing cost. Sulphur reduction has being studied using microwave irradiation set at 300W for 10 and 15minutes and oxidative- solvent extraction method using n- heptane and methanol by 1:1, 1:2 and 1:3 crude- solvent ratios after being oxidized with hydrogen peroxide, H2O2 oxidants. Percentage sulphur removal with n- heptane solvent by 1:1 and 1:2 are 81.73 and 85.47%; but extraction using methanol by different observed ratios gave less sulphur reduction. Indeed when microwave irradiated at 300W for 10 and 15minutes, 53.68 and 78.45% reduction were achieved. This indicates that microwave irradiation had caused oxidation by air in the oven cavity and results to formation of alkyl radicals and sulphoxide from sulphur compound in the petroleum. The prevailing sulphur found in the crude going by FT-IR results is sulphides which oxidized to sulphoxide or sulphones. It is clear that sulphur extraction with heptane is more efficient than microwave irradiation but economically due to demands for solvent and its industrial usage microwave irradiation can serve as alternative substitute for sulphur reduction in petroleum. Sulphur reduction by microwave radiation should be up- scaled from laboratory to a pilot plant without involving extraction column in the refining.

Sulphur and nitrogen supply - soil acidification and the absorption of nutrients in plants; Svovel og nitrogentilfoersel - jordforsuring og plantenes naeringstilgang

Energy Technology Data Exchange (ETDEWEB)

Abrahamsen, G

1996-01-01

Ecologically, soil is of the greatest interest as a growth medium for plants, and which affects the quality of ground water and surface water. In this connection, the paper looks upon how the increased deposition of sulphur, nitrogen and hydrogen ions affect the quality of soil as a growth medium for plants. Topics cover: Interaction between soil and plants, effects of acid rain in soil, and the effects of acid rain on plants. 11 refs., 1 tab.

Esterification of Free Fatty Acid in Crude Palm Oil Off Grade

Directory of Open Access Journals (Sweden)

Muhammad Dani Supardan

2009-12-01

Full Text Available The esterification of free fatty acids (FFA found in crude palm oil (CPO off grade with methanol is a promising technique to convert FFA into valuable fatty acid methyl ester (FAME, biodiesel and obtain a FFA-free oil that can be further transesterified using alkali bases. In this work, the effects of the main variables involved in the esterification process i.e. alcohol to oil molar ratio, reaction temperature, agitation speed and the initial amount of FFA of oil, were studied in the presence of sulphuric acid as catalyst at concentration of 1%-w. The experimental results show that the esterification process could lead to a practical and cost effective FFA removal unit in front of typical oil transesterification for biodiesel production. Keywords: CPO off grade, esterification, free fatty acid

78 FR 64526 - Information Collection Activities: Sulphur Operations; Submitted for Office of Management and...

Science.gov (United States)

2013-10-29

...: Sulphur Operations; Submitted for Office of Management and Budget (OMB) Review; Comment Request ACTION: 30... paperwork requirements in the regulations under Subpart P, Sulphur Operations. This notice also provides the..., Currently Under Review). SUPPLEMENTARY INFORMATION: Title: 30 CFR 250, Subpart P, Sulphur Operations. OMB...

Sulphur self as a bioindicator of air pollution

International Nuclear Information System (INIS)

Sihelska, N.; Semerad, M.; Cernansky, S.; Ruzickova, J.; Takacova, A.

2015-01-01

Road transport is one of the major sources of air polluting emissions. An average passenger car produces emissions of 228 g/km, trucks produce emissions of around 317 g/km. Emissions from combustion engines contain carbon dioxide, water vapour, nitrogen oxides, ammonia, carbon monoxide, unburned hydrocarbons, sulphur dioxide and various solids. Emissions also contain compounds of toxic metals/metalloids - arsenic, cadmium, chrome, nickel and lead. To detect metal/metalloid contamination from vehicle emissions, samples were collected and analyzed from biomass and soil near Bratislava's busiest road. We focused our attention on concentration of metals/metalloids in Laetiporus sulphureus because it's a very popular edible mushroom. Mushrooms are very good proxies for the state of nearby environment because of their excellent accumulation ability. (authors)

Ball-milling synthesis of ZnO@sulphur/carbon nanotubes and Ni(OH)_2@sulphur/carbon nanotubes composites for high-performance lithium-sulphur batteries

International Nuclear Information System (INIS)

Gu, Xingxing; Tong, Chuan-jia; Wen, Bo; Liu, Li-min; Lai, Chao; Zhang, Shanqing

2016-01-01

Highlights: • Metal oxides or hydroxides coating sulfur-based composite are successfully prepared. • Large-scale synthesis can be realized via the facile wet ball-milling strategy. • Density functional theory (DFT) calculation is applied to calculate adsorption energy. • ZnO exhibits a higher adsorption energy for Li_2S_8 than that Ni(OH)_2. • ZnO@sulphur/carbon nanotubes composite show excellent cycle and discharge performance. - Abstract: Zinc oxide wrapped sulphur/carbon nanotubes (ZnO@S/CNT) and nickel hydroxide wrapped sulphur/carbon nanotubes (Ni(OH)_2@S/CNT) nanocomposites are prepared using a simple, low cost and scalable ball-milling method. As the cathodes in Li-S batteries, the as-prepared ZnO@S/CNT composite illustrates a superior high initial capacity of 1663 mAh g"−"1 at a charge/discharge rate of 160 mA g"−"1, and maintains a reversible capacity at approximately 942 mAh g"−"1 after 70 cycles. While for Ni(OH)_2@S/CNT composites, its initial capacity is also as high as 1331 mAh g"−"1, but a poorer cycling stability is presented. When the charge/discharge current is increased to 1600 mA g"−"1, a high reversible capacity of 698 mAh g"−"1 after 200 cycles still can be obtained for the ZnO@S/CNT composite, far better than that of Ni(OH)_2@S/CNT composites. The better cycling performance and high discharge capacity can be attributed to the strong interactions between ZnO and S_x"2"− species, which is verified by the density functional theory (DFT) calculation result that the ZnO exhibits a higher adsorption energy for Li_2S_8 than the Ni(OH)_2.

Mesoporous titanium-manganese dioxide for sulphur mustard and soman decontamination

Energy Technology Data Exchange (ETDEWEB)

Stengl, Vaclav, E-mail: stengl@iic.cas.cz [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i., 250 68 Rez (Czech Republic); Bludska, Jana [Department of Solid State Chemistry, Institute of Inorganic Chemistry AS CR v.v.i., 250 68 Rez (Czech Republic); Oplustil, Frantisek; Nemec, Tomas [Military Technical Institute of Protection Brno, Veslarska 230, 628 00 Brno (Czech Republic)

2011-11-15

Highlights: {yields} New nano-dispersive materials for warfare agents decontamination. {yields} 95% decontamination activities for sulphur mustard. {yields} New materials base on titanium and manganese oxides. -- Abstract: Titanium(IV)-manganese(IV) nano-dispersed oxides were prepared by a homogeneous hydrolysis of potassium permanganate and titanium(IV) oxo-sulphate with 2-chloroacetamide. Synthesised samples were characterised using Brunauer-Emmett-Teller (BET) surface area and Barrett-Joiner-Halenda porosity (BJH), X-ray diffraction (XRD), infrared spectroscopy (IR), and scanning electron microscopy (SEM). These oxides were taken for an experimental evaluation of their reactivity with sulphur mustard (HD or bis(2-chloroethyl)sulphide) and soman (GD or (3,3'-dimethylbutan-2-yl)-methylphosphonofluoridate). Mn{sup 4+} content affects the decontamination activity; with increasing Mn{sup 4+} content the activity increases for sulphur mustard and decreases for soman. The best decontamination activities for sulphur mustard and soman were observed for samples TiMn{sub 3}7 with 18.6 wt.% Mn and TiMn{sub 5} with 2.1 wt.% Mn, respectively.

Rheology of dilute acid hydrolyzed corn stover at high solids concentration.

Science.gov (United States)

Ehrhardt, M R; Monz, T O; Root, T W; Connelly, R K; Scott, C T; Klingenberg, D J

2010-02-01

The rheological properties of acid hydrolyzed corn stover at high solids concentration (20-35 wt.%) were investigated using torque rheometry. These materials are yield stress fluids whose rheological properties can be well represented by the Bingham model. Yield stresses increase with increasing solids concentration and decrease with increasing hydrolysis reaction temperature, acid concentration, and rheometer temperature. Plastic viscosities increase with increasing solids concentration and tend to decrease with increasing reaction temperature and acid concentration. The solids concentration dependence of the yield stress is consistent with that reported for other fibrous systems. The changes in yield stress with reaction conditions are consistent with observed changes in particle size. This study illustrates that torque rheometry can be used effectively to measure rheological properties of concentrated biomass.

Effect of strong acids on red mud structural and fluoride adsorption properties.

Science.gov (United States)

Liang, Wentao; Couperthwaite, Sara J; Kaur, Gurkiran; Yan, Cheng; Johnstone, Dean W; Millar, Graeme J

2014-06-01

The removal of fluoride using red mud has been improved by acidifying red mud with hydrochloric, nitric and sulphuric acid. The acidification of red mud causes sodalite and cancrinite phases to dissociate, confirmed by the release of sodium and aluminium into solution as well as the disappearance of sodalite bands and peaks in infrared and X-ray diffraction data. The dissolution of these mineral phases increases the amount of available iron and aluminium oxide/hydroxide sites that are accessible for the adsorption of fluoride. However, concentrated acids have a negative effect on adsorption due to the dissolution of these iron and aluminium oxide/hydroxide sites. The removal of fluoride is dependent on the charge of iron and aluminium oxide/hydroxides on the surface of red mud. Acidifying red mud with hydrochloric, nitric and sulphuric acid resulted in surface sites of the form ≡SOH2(+) and ≡SOH. Optimum removal is obtained when the majority of surface sites are in the form ≡SOH2(+) as the substitution of a fluoride ion does not cause a significant increase in pH. This investigation shows the importance of having a low and consistent pH for the removal of fluoride from aqueous solutions using red mud. Copyright © 2014 Elsevier Inc. All rights reserved.

Leaching of copper concentrates with high arsenic content in chlorine-chloride media

International Nuclear Information System (INIS)

Herreros, O.; Fuentes, G.; Quiroz, R.; Vinals, J.

2003-01-01

This work reports the results of copper concentrates leaching which have high arsenic concepts (up to 2.5%). The treatments were carried out using chlorine that forms from sodium hypochlorite and sulphuric acid. The aim of this work is to obtain a solution having high copper content 4 to 6 g/l and 5 to 7 g/l free acid in order to submit it directly to a solvent extraction stage. In addition, this solution should have minimum content of arsenic and chloride ions. To carry out this investigation, an acrylic reactor was constructed where the leaching tests were made at constant temperature in a thermostatic bath under atmospheric pressure. The concentrate samples were obtained from mineral processing plants from Antofagasta, Chile. Typical variables were studied, such as leaching agent concentration, leaching time, pulp density and temperature among others. Some of the residues were analyzed by XRD and EPS. On the other hand, the solutions were analyzed by Atomic Absorption Spectroscopy. The results indicate solutions having the contents stated above can be obtained. (Author) 19 refs

Chelated Nitrogen-Sulphur-Codoped TiO2: Synthesis, Characterization, Mechanistic, and UV/Visible Photocatalytic Studies

Directory of Open Access Journals (Sweden)

Hayat Khan

2017-01-01

Full Text Available This study presents in detail the physicochemical, photoluminescent, and photocatalytic properties of carboxylic acid chelated nitrogen-sulphur-codoped TiO2. From the Fourier transform infrared spectroscopic study, it was revealed that the formate group formed bidentate bridging linkage while the acetate group coordinated in a bidentate chelating mode with a titanium precursor. In compliance with X-ray diffraction data, the anatase to rutile transformation temperature was extended due to carboxylic acid chelation and NS codoping. Raman analysis indicated four Raman peaks at 146, 392, 512, and 632 cm−1 for the precalcined chelated TiO2; on incorporation with NS dopants, an increase in Raman intensity for these peaks was recorded, indicating the structure stability of the anatase phase. Furthermore, X-ray photoelectron spectroscopic study revealed the presence of anionic doping of nitrogen and cationic doping of sulphur in the lattice of TiO2. When evaluating the UV-visible photodegradation rate of 4-chlorophenol, the modified TiO2 (NS0.06-TFA showed the highest photocatalytic activity. In connection with the activity tests, several scavenger agents were employed to elucidate the significance of the different reactive oxidizing species during the photocatalytic process. Moreover, the transfer pathways of photogenerated carriers and the photocatalytic reaction mechanism of modified TiO2 were also explained in detail.

Urban acid deposition in Greater Manchester

Energy Technology Data Exchange (ETDEWEB)

Lee, D.S.; Longhurst, J.W.S.; Gee, D.R.; Hare, S.E. (Manchester Polytechnic, Manchester (UK). Acid Rain Information Centre)

1989-08-01

Data are presented from a monitoring network of 18 bulk precipitation collectors and one wet-only collector in the urban area of Greater Manchester, in the north west of England. Weekly samples were analysed for all the major ions in precipitation along with gaseous nitrogen dioxide concentrations from diffusion tubes. Statistical analysis of the data shows significant spatial variation of non marine sulphate, nitrate, ammonium, acidity and calcium concentrations, and nitrogen dioxide concentrations. Calcium is thought to be responsible for the buffering of acidity and is of local origin. Wet deposition is the likely removal process for calcium in the atmosphere and probably by below cloud scavenging. Nitrate and ammonium concentrations and depositions show close spatial, temporal and statistical association. Examination of high simultaneous episodes of nitrate and ammonium deposition shows that these depositions cannot be explained in terms of trajectories and it is suggested that UK emissions of ammonia may be important. Statistical analysis of the relationships between nitrate and ammonium depositions, concentrations and precipitation amount suggest that ammonia from mesoscale sources reacts reversibly with nitric acid aerosol and is removed by below cloud scavenging. High episodes of the deposition of non marine sulphate are difficult to explain by trajectory analysis alone, perhaps suggesting local sources. In a comparison between wet deposition and bulk deposition, it was shown that only 15.2% of the non marine sulphur was dry deposited to the bulk precipitation collector. 63 refs., 86 figs., 31 tabs.

Electrochemical Determination of Low Molecular Mass Thiols Content in Potatoes (Solanum tuberosum Cultivated in the Presence of Various Sulphur Forms and Infected by Late Blight (Phytophora infestans

Directory of Open Access Journals (Sweden)

Rene Kizek

2008-05-01

Full Text Available In the present paper potato plants were cultivated in the presence of ammonium sulphate or elemental sulphur supplementation into the soil to reveal the effects of different sulphur forms on content of nitrogen, phosphorus, potassium, calcium, magnesium and sulphur, and yield of tubers. During the investigation of the influence of different sulphur forms on yield of potato tubers we did not observe significant changes. Average weight of tubers of control plants per one experimental pot was 355 g. Application of sulphur in both forms resulted in moderate potato tubers weight reduction per one experimental pot compared to control group; average value ranged from 320 to 350 g per one experimental pot. Further we treated the plants with two different supplementation of sulphur with cadmium(II ions (4 mg of cadmium(II acetate per kilogram of the soil. The significantly lowest cadmium content (p < 0.05 was determined in tissues of plants treated with the highest dosage of elemental sulphur (0.64 mg Cd/kg compared to control plants (0.82 mg Cd/kg. We also aimed our attention on the cadmium content in proteins, lipids or soluble carbohydrates and ash. Application of sulphate as well as elemental sulphur resulted in significant cadmium content reduction in lipid fraction compared to control plants. In addition to this we quantified content of low molecular mass thiols in potatoes tissues. To determine the thiols content we employed differential pulse voltammetry Brdicka reaction. After twelve days of the treatment enhancing of thiols level was observed in all experimental groups regardless to applied sulphur form and its concentration. Finally we evaluated the effect of sulphur supplementation on Phytophora infestans infection of potato plants.

Sulphur management in onion (Allium cepa) cultivation in hills of Himachal Pradesh.

Science.gov (United States)

Jaggi, R C; Sharma, R K

2010-05-01

Field experiment were conducted at CSK HPKV Research Farm, Palampur during Rabi seasons of 2000-01 and 2001-02, to study the response of onion (Allium cepa var Patna red) at four sulphur levels (0, 15, 30 and 60 kg ha(-1)) applied through Gypsum and S95. The analysis was done to allocate the limited availability of sulphur for maximizing net profit over fertilizer cost. The results show that the dose of sulphur under its full availability is 43.02 kg ha(-1). But under its scarce availability the maximum benefit would occur when it is applied up to 32.11 kg ha(-1) followed by even distribution of fertilizer i.e. 20 kg ha(-1). The returns following sulphur application at these rates, would be Rs 69340, 73092 and 68700 ha(-1) respectively.

High pressure treatments accelerate changes in volatile composition of sulphur dioxide-free wine during bottle storage.

Science.gov (United States)

Santos, Mickael C; Nunes, Cláudia; Rocha, M Angélica M; Rodrigues, Ana; Rocha, Sílvia M; Saraiva, Jorge A; Coimbra, Manuel A

2015-12-01

The impact of high hydrostatic pressure (HHP) treatments on volatile composition of sulphur dioxide-free wines during bottle storage was studied. For this purpose, white and red wines were produced without sulphur dioxide (SO2) and, at the end of the alcoholic fermentation, the wines were pressurised at 500 MPa and 425 MPa for 5 min. Wine with 40 ppm of SO2 and a wine without a preservation treatment were used as controls. More than 160 volatile compounds, distributed over 12 chemical groups, were identified in the wines by an advanced gas chromatography technique. The pressurised wines contained a higher content of furans, aldehydes, ketones, and acetals, compared with unpressurised wines after 9 months of storage. The changes in the volatile composition indicate that HHP treatments accelerated the Maillard reaction, and alcohol and fatty acid oxidation, leading to wines with a volatile composition similar to those of faster aged and/or thermally treated wines. Copyright © 2015 Elsevier Ltd. All rights reserved.

Heavy metal concentration of settled surface dust in residential building

International Nuclear Information System (INIS)

Nor Aimi abdul Wahab; Fairus Muhamad Darus; Norain Isa; Siti Mariam Sumari; Nur Fatihah Muhamad Hanafi

2012-01-01

The concentrations of heavy metals (Cu, Ni, Pb and Zn) in settled surface dust were collected from nine residential buildings in different areas in Seberang Prai Tengah District, Pulau Pinang. The samples of settled surface dust were collected in 1 m 2 area by using a polyethylene brush and placed in the dust pan by sweeping the living room floor most accessible to the occupants. Heavy metals concentrations were determined by using inductively coupled plasma optical emission spectrometer (ICP-OES) after digestion with nitric acid and sulphuric acid. The results show that the range of heavy metals observed in residential buildings at Seberang Prai Tengah were in the range of 2.20-14.00 mg/ kg, 1.50-32.70 mg/ kg, 1.50-76.80 mg/ kg and 14.60-54.40 mg/ kg for Cu, Ni, Pb and Zn respectively. The heavy metal concentration in the investigated areas followed the order: Pb > Zn > Ni > Cu. Statistical analysis indicates significant correlation between all the possible pairs of heavy metal. The results suggest a likely common source for the heavy metal contamination, which could be traced most probably to vehicular emissions, street dust and other related activities. (author)

Integrated sulphur management : gas, oil sands, reclamation and the challenges of fluctuating demand

International Nuclear Information System (INIS)

Pineau, R.

2009-01-01

International Commodities Export Corporation is a privately held company that provides fully integrated service offerings to add maximum value in designing, building, owning, and operating sulphur assets. The company also offers in-house, engineering, procurement and project management, as well as supply management, transportation and distribution services. It also has expertise in marine transportation. This presentation discussed integrated sulphur management, with particular focus on gas, oil sands, reclamation and the challenges of fluctuating demand. The presentation provided an overview of the sulphur market and oil sands sulphur. Key considerations for oil sands producers were also presented. The challenges of fluctuating demand include price and volume considerations; logistics; geography and distance to market; export/offshore versus domestic/United States; seasonal considerations; and an inelastic sulphur market. The presentation concluded with a status update of ICEC's initiative and the advantages of Prince Rupert, an economically viable export infrastructure to producers without onsite forming facilities. figs

Effect of Nitric Acid Concentrations on Synthesis and Stability of Maghemite Nanoparticles Suspension

Directory of Open Access Journals (Sweden)

Irwan Nurdin

2014-01-01

Full Text Available Maghemite (γ-Fe2O3 nanoparticles have been synthesized using a chemical coprecipitation method at different nitric acid concentrations as an oxidizing agent. Characterization of all samples performed by several techniques including X-ray diffraction (XRD, transmission electron microscopy (TEM, alternating gradient magnetometry (AGM, thermogravimetric analysis (TGA, dynamic light scattering (DLS, and zeta potential. The XRD patterns confirmed that the particles were maghemite. The crystallite size of all samples decreases with the increasing concentration of nitric acid. TEM observation showed that the particles have spherical morphology with narrow particle size distribution. The particles showed superparamagnetic behavior with decreased magnetization values at the increasing concentration of nitric acid. TGA measurement showed that the stability temperature decreases with the increasing concentration of nitric acid. DLS measurement showed that the hydrodynamic particle sizes decrease with the increasing concentration of nitric acid. Zeta potential values show a decrease with the increasing concentration of nitric acid. The increasing concentration of nitric acid in synthesis of maghemite nanoparticles produced smaller size particles, lower magnetization, better thermal stability, and more stable maghemite nanoparticles suspension.

High serum uric acid concentration predicts poor survival in patients with breast cancer.

Science.gov (United States)

Yue, Cai-Feng; Feng, Pin-Ning; Yao, Zhen-Rong; Yu, Xue-Gao; Lin, Wen-Bin; Qian, Yuan-Min; Guo, Yun-Miao; Li, Lai-Sheng; Liu, Min

2017-10-01

Uric acid is a product of purine metabolism. Recently, uric acid has gained much attraction in cancer. In this study, we aim to investigate the clinicopathological and prognostic significance of serum uric acid concentration in breast cancer patients. A total of 443 female patients with histopathologically diagnosed breast cancer were included. After a mean follow-up time of 56months, survival was analysed using the Kaplan-Meier method. To further evaluate the prognostic significance of uric acid concentrations, univariate and multivariate Cox regression analyses were applied. Of the clinicopathological parameters, uric acid concentration was associated with age, body mass index, ER status and PR status. Univariate analysis identified that patients with increased uric acid concentration had a significantly inferior overall survival (HR 2.13, 95% CI 1.15-3.94, p=0.016). In multivariate analysis, we found that high uric acid concentration is an independent prognostic factor predicting death, but insufficient to predict local relapse or distant metastasis. Kaplan-Meier analysis indicated that high uric acid concentration is related to the poor overall survival (p=0.013). High uric acid concentration predicts poor survival in patients with breast cancer, and might serve as a potential marker for appropriate management of breast cancer patients. Copyright © 2017 Elsevier B.V. All rights reserved.

Chronic aspartame intake causes changes in the trans-sulphuration pathway, glutathione depletion and liver damage in mice

Directory of Open Access Journals (Sweden)

Isabela Finamor

2017-04-01

Full Text Available No-caloric sweeteners, such as aspartame, are widely used in various food and beverages to prevent the increasing rates of obesity and diabetes mellitus, acting as tools in helping control caloric intake. Aspartame is metabolized to phenylalanine, aspartic acid, and methanol. Our aim was to study the effect of chronic administration of aspartame on glutathione redox status and on the trans-sulphuration pathway in mouse liver. Mice were divided into three groups: control; treated daily with aspartame for 90 days; and treated with aspartame plus N-acetylcysteine (NAC. Chronic administration of aspartame increased plasma alanine aminotransferase (ALT and aspartate aminotransferase activities and caused liver injury as well as marked decreased hepatic levels of reduced glutathione (GSH, oxidized glutathione (GSSG, γ-glutamylcysteine ​​(γ-GC, and most metabolites of the trans-sulphuration pathway, such as cysteine, S-adenosylmethionine (SAM, and S-adenosylhomocysteine ​​(SAH. Aspartame also triggered a decrease in mRNA and protein levels of the catalytic subunit of glutamate cysteine ligase (GCLc and cystathionine γ-lyase, and in protein levels of methionine adenosyltransferase 1A and 2A. N-acetylcysteine prevented the aspartame-induced liver injury and the increase in plasma ALT activity as well as the decrease in GSH, γ-GC, cysteine, SAM and SAH levels and GCLc protein levels. In conclusion, chronic administration of aspartame caused marked hepatic GSH depletion, which should be ascribed to GCLc down-regulation and decreased cysteine levels. Aspartame triggered blockade of the trans-sulphuration pathway at two steps, cystathionine γ-lyase and methionine adenosyltransferases. NAC restored glutathione levels as well as the impairment of the trans-sulphuration pathway.

Chronic aspartame intake causes changes in the trans-sulphuration pathway, glutathione depletion and liver damage in mice.

Science.gov (United States)

Finamor, Isabela; Pérez, Salvador; Bressan, Caroline A; Brenner, Carlos E; Rius-Pérez, Sergio; Brittes, Patricia C; Cheiran, Gabriele; Rocha, Maria I; da Veiga, Marcelo; Sastre, Juan; Pavanato, Maria A

2017-04-01

No-caloric sweeteners, such as aspartame, are widely used in various food and beverages to prevent the increasing rates of obesity and diabetes mellitus, acting as tools in helping control caloric intake. Aspartame is metabolized to phenylalanine, aspartic acid, and methanol. Our aim was to study the effect of chronic administration of aspartame on glutathione redox status and on the trans-sulphuration pathway in mouse liver. Mice were divided into three groups: control; treated daily with aspartame for 90 days; and treated with aspartame plus N-acetylcysteine (NAC). Chronic administration of aspartame increased plasma alanine aminotransferase (ALT) and aspartate aminotransferase activities and caused liver injury as well as marked decreased hepatic levels of reduced glutathione (GSH), oxidized glutathione (GSSG), γ-glutamylcysteine ​​(γ-GC), and most metabolites of the trans-sulphuration pathway, such as cysteine, S-adenosylmethionine (SAM), and S-adenosylhomocysteine ​​(SAH). Aspartame also triggered a decrease in mRNA and protein levels of the catalytic subunit of glutamate cysteine ligase (GCLc) and cystathionine γ-lyase, and in protein levels of methionine adenosyltransferase 1A and 2A. N-acetylcysteine prevented the aspartame-induced liver injury and the increase in plasma ALT activity as well as the decrease in GSH, γ-GC, cysteine, SAM and SAH levels and GCLc protein levels. In conclusion, chronic administration of aspartame caused marked hepatic GSH depletion, which should be ascribed to GCLc down-regulation and decreased cysteine levels. Aspartame triggered blockade of the trans-sulphuration pathway at two steps, cystathionine γ-lyase and methionine adenosyltransferases. NAC restored glutathione levels as well as the impairment of the trans-sulphuration pathway. Copyright © 2017. Published by Elsevier B.V.

Effect of sulphur fertilisation on yield and quality of white mustard seeds

Directory of Open Access Journals (Sweden)

Pavel Ryant

2009-01-01

Full Text Available The objective of the present study was to estimate the effect of different forms of sulphur on yields and qualitative parameters of white mustard seeds. This topic was studied in 2004 in the form of a pot trial in a vegetation hall and linked up with an identical experiment with spring wheat conducted in 2003. Besides the control variant not fertilised with sulphur (1 we fertilised the soil with elemental sulphur (2, ammonium sulphate (3 and gypsum (4 and applied foliar dressing of elemental sulphur with bentonite (5. For all variants the nitrogen dose was 0.9 g per pot (0.15 g . kg−1 of soil and for va­riants 2 to 4 it was 1 g of sulphur per pot (0.17 g. kg−1 of soil. Foliar dressing of elemental sulphur (S0 was not applied until the stage of six true leaves in a dose of 10 kg per ha (0.032 g per pot.Significantly higher yields of white mustard seeds were achieved after foliar application of S0 which can be also due to its fungicide action. The variants where gypsum was applied showed the highest average number of branches and pods and also straw yields. After gypsum fertilisation or foliar application of S0 the oil content in the mustard seeds exceeded 25%; this is the minimal content required for the production of good quality mustard. The 1000-seed weight was significantly higher after foliar application of S0. The proportion of seeds greyish on the surface, a sign of mildew, significantly decreased after fertilisation with all forms of sulphur, but most of all after foliar application of S0.Fertilisation with ammonium sulphate reduced the exchangeable soil reaction after harvest. On the other hand gypsum alkalised the soil environment and increased the content of available calcium and water-soluble sulphur. The soil of the variant where foliar dressing of S0 was applied had a higher content of available calcium after harvest. The least amount of available sulphur and phosphorus in the soil was seen after foliar

Acid ran and below-cloud scavenging in south-western China

International Nuclear Information System (INIS)

Tanner, P.A.; Lei, H.C.; Huang, M.Y.; Shen, Z.L.

1997-01-01

Major urban areas in south-western China exhibit unique air pollution problems due to increasing use of high sulphur-content fuels in an environment of unfavourable topography and climate. Ambient levels of sulphur dioxide exceed the air quality objectives, and this gas is the major precursor of acid rain. Cloudwater chemistry studies are reported for urban, suburban and countryside locations, during the period 1985-89. Although cloudwater acidity was found to increase towards the cloud base, the acidity was much greater for rainwater samples collected simultaneously, and was more pronounced in urban rather than neighbouring suburban or countryside regions. The main contribution to the acidity arises from below-cloud scavenging of gas and aerosol and model calculations are able to simulate this behaviour

Biotic conversion of sulphate to sulphide and abiotic conversion of sulphide to sulphur in a microbial fuel cell using cobalt oxide octahedrons as cathode catalyst.

Science.gov (United States)

Chatterjee, Pritha; Ghangrekar, M M; Rao, Surampalli; Kumar, Senthil

2017-05-01

Varying chemical oxygen demand (COD) and sulphate concentrations in substrate were used to determine reaction kinetics and mass balance of organic matter and sulphate transformation in a microbial fuel cell (MFC). MFC with anodic chamber volume of 1 L, fed with wastewater having COD of 500 mg/L and sulphate of 200 mg/L, could harvest power of 54.4 mW/m 2 , at a Coulombic efficiency of 14%, with respective COD and sulphate removals of 90 and 95%. Sulphide concentration, even up to 1500 mg/L, did not inhibit anodic biochemical reactions, due to instantaneous abiotic oxidation to sulphur, at high inlet sulphate. Experiments on abiotic oxidation of sulphide to sulphur revealed maximum oxidation taking place at an anodic potential of -200 mV. More than 99% sulphate removal could be achieved in a MFC with inlet COD/sulphate of 0.75, giving around 1.33 kg/m 3  day COD removal. Bioelectrochemical conversion of sulphate facilitating sulphur recovery in a MFC makes it an interesting pollution abatement technique.

Hair analysis as a useful procedure for detection of vapour exposure to chemical warfare agents: simulation of sulphur mustard with methyl salicylate.

Science.gov (United States)

Spiandore, Marie; Piram, Anne; Lacoste, Alexandre; Josse, Denis; Doumenq, Pierre

2014-06-01

Chemical warfare agents (CWA) are highly toxic compounds which have been produced to kill or hurt people during conflicts or terrorist attacks. Despite the fact that their use is strictly prohibited according to international convention, populations' exposure still recently occurred. Development of markers of exposure to CWA is necessary to distinguish exposed victims from unexposed ones. We present the first study of hair usage as passive sampler to assess contamination by chemicals in vapour form. This work presents more particularly the hair adsorption capacity for methyl salicylate used as a surrogate of the vesicant sulphur mustard. Chemical vapours toxicity through the respiratory route has historically been defined through Haber's law's concentration-time (Ct) product, and vapour exposure of hair to methyl salicylate was conducted with various times or doses of exposure in the range of incapacitating and lethal Ct products corresponding to sulphur mustard. Following exposure, extraction of methyl salicylate from hair was conducted by simple soaking in dichloromethane. Methyl salicylate could be detected on hair for vapour concentration corresponding to about one fifth of the sulphur mustard concentration that would kill 50% of exposed individuals (LCt50). The amount of methyl salicylate recovered from hair increased with time or dose of exposure. It showed a good correlation with the concentration-time product, suggesting that hair could be used like a passive sampler to assess vapour exposure to chemical compounds. It introduces great perspectives concerning the use of hair as a marker of exposure to CWA. Copyright © 2014 John Wiley & Sons, Ltd.

Determination of concentration and molar absorptivity of hypochlorous acid and hypobromous acid species by hydrogen peroxide titration

Science.gov (United States)

Uehara, H.; Arakaki, T.

2017-12-01

Hypochlorous acid and hypobromous acid (abbreviated as "HypoX acids") are the main ingredients of bleaching and bactericides. The HypoX acids change their chemical forms depending on environmental factors such as pH and various chemical reactions. For example, it has been reported that hypobromite ion in water changes to carcinogenic bromate by photochemical reaction with ultraviolet light. In this study, concentrations of HypoX acids were determined by UV-VIS absorbance measurement utilizing the fact that HypoX acids react with hydrogen peroxide and do not co-exist in the solution. The method for determining the concentration by titration with hydrogen peroxide can be carried out simpler and more efficiently than the DPD method or the current titration method generally used for chlorine concentration measurement. Molar absorptivity between 250 - 500 nm of HypoX acids, including their conjugate base species, was determined by solving theoretical acid-base formula including molar fraction of each chemical species at various pHs. Molar absorptivity of OCl- and OBr- between 250 - 500 nm was determined based on the concentrations obtained from titration with hydrogen peroxide and absorbance at pH > 10, where OCl- and OBr- dominate. Furthermore, the HypoX acids solutions were irradiated with a solar simulator, and the photolysis rate constants were obtained. Based on those values, the half-lives were calculated and the behavior of HypoX acids in the environment was elucidated.

Investigation of the possibility of binding fly ash particles by elemental sulphur

Directory of Open Access Journals (Sweden)

Vidojković V.

2006-01-01

Full Text Available Thermal power plants in Serbia use lignite for electrical power production The secondary product of coal combustion is fly ash in the amount of 17%. Fly ash causes the pollution of air, water and soil, and also cause many human, especially lung diseases. Secondary sulphur is a product of crude oil refining. The aim of this study was to investigate the use of sulphur as a bonding material in ultra fine particle agglomeration (smaller than 63 μm in fly ash. The agglomeration should make the ash particles larger and heavy enough to fall without flying fractions. The experiments showed that during the homogenization of the ashes and sulphur from 150 to 170 °C in a reactor with intensive mixing, an amount of 15% sulphur was sufficient to bond particles and cause agglomeration without visible flying fractions.

Assessment of acidity levels in Eucalyptus Camaldulensis barks ...

African Journals Online (AJOL)

Bark samples of Eucalyptus camaldulensis obtained from Bauchi and Gombe States were analysed spectrophotometrically for their sulphate-sulphur content. The aim was to assess the extent of sulphur pollution in the environment. The results showed that S concentration ranged from 0.79 to 1.70mg/g for samples from ...

Study and application on lean resin converting in uranium mill

International Nuclear Information System (INIS)

Zhao Shaoxi; Huang Qijin; Zhu Shuguang; Yi Faqing; Du Wenjie

2012-01-01

The field test about sulphuric acid used to convert lean resin was finished. The results indicated sulphuric acid could replace chlorin in lean resin and could be reclaimed to desorption procedure. The consumption of NaCl decreased, the chlorin concentration of tailing decreased too. Both of uranium loss and waste water volume were reduced. The uranium concentration of tailing decreased and energy saving and emission reduction can be achieved. (authors)

Ultrasound-assisted extraction for total sulphur measurement in mine tailings

Energy Technology Data Exchange (ETDEWEB)

Khan, Adnan Hossain, E-mail: ad_li2@yahoo.com [Department of Civil and Environmental Engineering, University of Western Ontario (Canada); Shang, Julie Q.; Alam, Raquibul [Department of Civil and Environmental Engineering, University of Western Ontario (Canada)

2012-10-15

Highlights: Black-Right-Pointing-Pointer We develop a total sulphur measuring procedure of mine tailings. Black-Right-Pointing-Pointer Ultrasound is used in the sample pre-treatment process. Black-Right-Pointing-Pointer Full factorial design is applied to identify the best level of effecting factors. - Abstract: A sample preparation method for percentage recovery of total sulphur (%S) in reactive mine tailings based on ultrasound-assisted digestion (USAD) and inductively coupled plasma-optical emission spectroscopy (ICP-OES) was developed. The influence of various methodological factors was screened by employing a two-level and three-factor (2{sup 3}) full factorial design and using KZK-1, a sericite schist certified reference material (CRM), to find the optimal combination of studied factors and %S. Factors such as the sonication time, temperature and acid combination were studied, with the best result identified as 20 min of sonication, 80 Degree-Sign C temperature and 1 ml of HNO{sub 3}:1 ml of HCl, which can achieve 100% recovery for the selected CRM. Subsequently a fraction of the 2{sup 3} full factorial design was applied to mine tailings. The percentage relative standard deviation (%RSD) for the ultrasound method is less than 3.0% for CRM and less than 6% for the mine tailings. The investigated method was verified by X-ray diffraction analysis. The USAD method compared favorably with existing methods such as hot plate assisted digestion method, X-ray fluorescence and LECO Trade-Mark-Sign -CNS method.

Transport of metals and sulphur in magmas by flotation of sulphide melt on vapour bubbles

Science.gov (United States)

Mungall, J. E.; Brenan, J. M.; Godel, B.; Barnes, S. J.; Gaillard, F.

2015-03-01

Emissions of sulphur and metals from magmas in Earth’s shallow crust can have global impacts on human society. Sulphur-bearing gases emitted into the atmosphere during volcanic eruptions affect climate, and metals and sulphur can accumulate in the crust above a magma reservoir to form giant copper and gold ore deposits, as well as massive sulphur anomalies. The volumes of sulphur and metals that accumulate in the crust over time exceed the amounts that could have been derived from an isolated magma reservoir. They are instead thought to come from injections of multiple new batches of vapour- and sulphide-saturated magmas into the existing reservoirs. However, the mechanism for the selective upward transfer of sulphur and metals is poorly understood because their main carrier phase, sulphide melt, is dense and is assumed to settle to the bottoms of magma reservoirs. Here we use laboratory experiments as well as gas-speciation and mass-balance models to show that droplets of sulphide melt can attach to vapour bubbles to form compound drops that float. We demonstrate the feasibility of this mechanism for the upward mobility of sulphide liquids to the shallow crust. Our work provides a mechanism for the atmospheric release of large amounts of sulphur, and contradicts the widely held assumption that dense sulphide liquids rich in sulphur, copper and gold will remain sequestered in the deep crust.

the amino acid composition of selected south african feed ingredients

African Journals Online (AJOL)

of assessing the balance of amino acids, each is presented as a percentage of the requirements of broilers up to 3 weeks of age. ... nutritional importance of the total sulphur amino acids .... out and the primary amino acid analysis result sheet.

Ion exchange separation of low boric acid concentrations from water

International Nuclear Information System (INIS)

Kysela, J.; Brabec, J.; Peterka, F.

1975-01-01

Boric acid poisoning of the moderator of the TR-O experimental heavy water reactor was studied. The possibility is discussed of removing boric acid from heavy water by means of a strong basic anion exchanger, below the residual concentration of 0.01 mg B/l. Measurements of the usable capacities of the strong basic anion exchanger Zerollit FF showed that the penetration of boric acid during the sorption period does not exceed the value of 0.015 mg B/l. The dependence was found of capacity on the boric acid concentration in the solution. Analytical methods used to determine B in water are also described. (author)

Hypothermia reduces sulphur mustard toxicity

International Nuclear Information System (INIS)

Mi Lei; Gong Wenrong; Nelson, Peggy; Martin, Leanne; Sawyer, Thomas W.

2003-01-01

The effect of temperature on the development of sulphur mustard (HD)-induced toxicity was investigated in first passage cultures of human skin keratinocytes and on hairless guinea pig skin. When cells exposed to HD were incubated at 37 deg. C, a concentration-dependent decline in viability was observed that was maximal by 2 days. In contrast, no significant HD-induced toxicity was evident up to 4 days posttreatment when the cells were incubated at 25 deg. C. However, these protective effects were lost by 24 h when the cells were switched back to 37 deg. C. The protective effects of hypothermia were also demonstrated when apoptotic endpoints were examined. The HD concentration-dependent induction of fragmented DNA (as quantitated using soluble DNA and the TUNEL reaction), morphology, and p53 expression were all significantly depressed when cell cultures were incubated at 25 deg. C compared to 37 deg. C. When animals were exposed to HD vapour for 2, 4, and 6 min and left at room temperature, lesions were produced whose severity was dependent on exposure time and that were maximal by 72 h posttreatment. Moderate cooling (5-10 deg. C) of HD exposure sites posttreatment (4-6 h) significantly reduced the severity of the resultant lesions. However, in contrast to the in vitro results, these effects were permanent. It appears that the early and noninvasive act of cooling HD-exposed skin may provide a facile means of reducing the severity of HD-induced cutaneous lesions

Effect of succinic acid concentration in poly(glycerol citrate/succinate) properties

International Nuclear Information System (INIS)

Brioude, Michel M.; Guimaraes, Danilo H.; Fiuza, Raigenis P.; Jose, Nadia M.

2011-01-01

In this work were prepared and characterized polymer based on glycerol, citric and succinic acid, in three different ratios to evaluate the effect of succinic acid concentration in materials properties. The polymers were obtained by polycondensation reaction between polyol and poly acids, and were characterized by X-ray diffraction (XRD), infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), scanning differential calorimetry (DSC), scanning electron microscopy (SEM). The materials are amorphous polyesters and its thermal and morphological properties change depending on the succinic acid concentration. (author)

Effect of feedstock end boiling point on product sulphur during ultra deep diesel hydrodesulphurization

Energy Technology Data Exchange (ETDEWEB)

Stratiev, D.; Ivanov, A.; Jelyaskova, M. [Lukoil Neftochim Bourgas AD, Bourgas (Bulgaria)

2004-12-01

An investigation was carried out to test the feasibility of producing 50 and 10 ppm sulphur diesel in a conventional hydrotreating unit operating at low pressure conditions by varying the feedstock end boiling point. Middle distillate fractions distilled from a mixture of Ural crude oil, reduced crude, vacuum gas oil, naphtha and low sulphur crude oils with 95% vol. points of 274, 359, 343, 333, and 322 C (ASTM D-86 method) and sulphur contents of 0.36, 0.63, 0.99, 0.57, and 0.47%, respectively, were hydrotreated using the Akzo Nobel Stars family Co-Mo KF-757 catalyst in a trickle bed pilot plant at following conditions: reactor inlet temperature range of 320-360 C; liquid hourly space velocity (LHSV) range of 1-2 h{sup -1}; total reactor pressure of 3.5 MPa; treating gas: feedstock ratio of 250 Nm{sup 3}/m{sup 3}. It was found that the determinant factor for the attainment of ultra low sulphur levels during middle distillate hydrodesulphurization was not the total sulphur content in the feed but the content of the material boiling above 340 C (according to TBP). For all LHSVs and reactor inlet temperatures studied the product sulphur dependence on the feed 340 C+ fraction content was approximated by second order power law. The specification of 50 ppm sulphur was achieved with all studied feedstocks. However the 10ppm sulphur limit could be met only by feedstocks with 95% vol. points below 333 C, which is accompanied by about 10% reduction of the diesel potential. The hydrotreatment tests on a blend 80% straight run gas oil (ASTM D-86 95% vol. of 274 C)/20%FCC LCO (ASTM D-86 95% vol. of 284 C) showed product sulphur levels which were not higher than those obtained by hydrotreatment of the straight run gas oil, indicating that undercutting the FCC LCO gives the refiner the opportunity to increase the potential for the production of 10 ppm sulphur diesel at the conditions of the conventional hydrotreating unit operating at low pressure. The product cetane index was

How do organic vapors contribute to new-particle formation?

CERN Document Server

Donahue, Neil M; Chuang, Wayne; Riipinen, Ilona; Riccobono, Francesco; Schobesberger, Siegfried; Dommen, Josef; Baltensperger, Urs; Kulmala, Markku; Worsnop, Douglas R; Vehkamaki, Hanna

2013-01-01

Highly oxidised organic vapors can effectively stabilize sulphuric acid in heteronuclear clusters and drive new-particle formation. We present quantum chemical calculations of cluster stability, showing that multifunctional species can stabilize sulphuric acid and also present additional polar functional groups for subsequent cluster growth. We also model the multi-generation oxidation of vapors associated with secondary organic aerosol formation using a two-dimensional volatility basis set. The steady-state saturation ratios and absolute concentrations of extremely low volatility products are sufficient to drive new-particle formation with sulphuric acid at atmospherically relevant rates.

Dispersion of sulphur in the northern hemisphere. A study with a 3-dimensional time-resolved model

Energy Technology Data Exchange (ETDEWEB)

Tarrason, L

1996-12-31

This thesis on atmospheric dispersion of sulphur presents a calculation of intercontinental transport of oxidized sulphur and allocates different contributions to sulphur background levels over Europe. It is found that a significant fraction of anthropogenic sulphur (AS) is transported out of continental boundaries thus affecting the background levels over major parts of the northern hemisphere. Over Europe, the contribution of AS from North America is similar in amount to that of Asian AS and natural sources from the North Atlantic Ocean. Although the yearly contribution of intercontinental transport to deposition of sulphur over Europe is quite small, it can be much more important over certain areas and seasons and is comparable to the contributions from individual European countries. The calculations are based on a three-dimensional Eulerian time-resolved model that describes sulphur dispersion in the atmosphere in connection with large-scale synoptic flows and agree well with observations. The thesis emphasizes the role of synoptic scale atmospheric motions in determining intercontinental transport of sulphur. It indicates the need to resolve individual cyclones and anticyclones in order to describe the dispersion and distribution of atmospheric sulphur in the northern hemisphere and stresses the value of comparing model calculations with observations, both in atmospheric chemistry studies and in climate applications. 260 refs., 50 figs., 17 tabs.

Dispersion of sulphur in the northern hemisphere. A study with a 3-dimensional time-resolved model

Energy Technology Data Exchange (ETDEWEB)

Tarrason, L.

1995-12-31

This thesis on atmospheric dispersion of sulphur presents a calculation of intercontinental transport of oxidized sulphur and allocates different contributions to sulphur background levels over Europe. It is found that a significant fraction of anthropogenic sulphur (AS) is transported out of continental boundaries thus affecting the background levels over major parts of the northern hemisphere. Over Europe, the contribution of AS from North America is similar in amount to that of Asian AS and natural sources from the North Atlantic Ocean. Although the yearly contribution of intercontinental transport to deposition of sulphur over Europe is quite small, it can be much more important over certain areas and seasons and is comparable to the contributions from individual European countries. The calculations are based on a three-dimensional Eulerian time-resolved model that describes sulphur dispersion in the atmosphere in connection with large-scale synoptic flows and agree well with observations. The thesis emphasizes the role of synoptic scale atmospheric motions in determining intercontinental transport of sulphur. It indicates the need to resolve individual cyclones and anticyclones in order to describe the dispersion and distribution of atmospheric sulphur in the northern hemisphere and stresses the value of comparing model calculations with observations, both in atmospheric chemistry studies and in climate applications. 260 refs., 50 figs., 17 tabs.

Effect of Sulphur Fertilization on Grain Quality and Protein Composition of Durum Wheat (Triticum durum Desf.

Directory of Open Access Journals (Sweden)

Marianna Pompa

2009-12-01

Full Text Available The reduction of atmosphere emission of SO2 and the massive use of fertilizers high in nitrogen and phosphorus resulted in a decrease of the sulphur content in the soil. In durum wheat cultivation, sulphur supply plays a key role not only for plant growth, but also for grain quality. Sulphur is an essential macronutrient primarily used to synthesize methionine and cysteine and it is also involved in establishing protein structures by disulphide bonds. The aim of this study was to evaluate the effect of sulphur nutrition on grain quality and protein composition of durum wheat cultivars grown under water deficit conditions, typical of Mediterranean areas. To this purpose, in the 2003-2004 and 2004-2005 crop seasons a field trial was carried out by comparing two water regimes (irrigated and rainfed, two sulphur fertilizer levels and two durum wheat cultivars. Under our experimental conditions, an increase in protein and gluten content in the rainfed treatment and a positive effect of sulphur fertilization on quality parameters were observed. Few changes were observed in protein composition in response to sulphur fertilization.

ORGANIC ACIDS CONCENTRATION IN WINE STOCKS AFTER Saccharomyces cerevisiae FERMENTATION

Directory of Open Access Journals (Sweden)

V. N. Bayraktar

2013-04-01

Full Text Available The biochemical constituents in wine stocks that influence the flavor and quality of wine are investigated in the paper. The tested parameters consist of volume fraction of ethanol, residual sugar, phenolic compounds, tartaric, malic, citric, lactic, acetic acids, titratable acidity and volatile acids. The wine stocks that were received from white and red grape varieties Tairov`s selection were tested. There was a correlation between titratable acidity and volatile acids in the wine stocks from white and red grape varieties. High correlation was also found between lactic and acetic acids, between volatile acids, acetic acid and sugar. It was determined that wine stocks with a high concentration of ethanol originated from those yeast strains of Saccharomyces cerevisiae, in a fermented grape must of high speed of enzyme activity. The taste of wine stocks correlated with the ratio of tartaric to malic acid. Analysis showed significant differences between the varieties of white and red wine stocks in concentrations of organic acids, phenolic compounds, residual sugar, and volume fraction of ethanol. Positive correlation was indicated for both studied groups for volatile acids and acetic acid, tartaric, malic, lactic acids and total sugar. Prospective yeast cultures with high productivity of alcohol (ethanol were selected for winemaking biotechnology.

Remediation of grey forest soils heavily polluted with heavy metals by means of their leaching at acidic pH followed by the soil reclamation by means of neutralization and bacterial manure addition

Science.gov (United States)

Georgiev, Plamen; Groudev, Stoyan; Spasova, Irena; Nicolova, Marina

2014-05-01

Some grey forest soils in Western Bulgaria are heavily polluted with heavy metals (copper, lead, and zinc), arsenic, and uranium due to the infiltration of acid mine drainage generated at the abandoned uranium mine Curilo. This paper presents some results from a study about soil remediation based on the contaminants leaching from the topsoil by means of irrigation with solutions containing sulphuric acid or its in situ generation by means of sulphur-oxidizing chemolithotrophic bacteria in or without the presence of finely cut straw. These methods were tested in large scale zero suction lysimeters. The approaches based on S° and finely cut straw addition was the most efficient amongst the tested methods and for seven months of soil remediation the concentration of all soil contaminants were decreased below the relevant Maximum Admissible Concentration (MAC). Neutralization of the soil acidity was applied as a next stage of soil reclamation by adding CaCO3 and cow manure. As a result, soil pH increased from strongly acidic (2.36) to slightly acidic (6.15) which allowed subsequent addition of humic acids and bacterial manure to the topsoil. The soil habitat changed in this way facilitated the growth of microorganisms which restored the biogeochemical cycles of nitrogen and carbon to the levels typical for non-polluted grey forest soil.

Mantle to surface degassing of carbon- and sulphur-rich alkaline magma at El Hierro, Canary Islands

Science.gov (United States)

Longpré, Marc-Antoine; Stix, John; Klügel, Andreas; Shimizu, Nobumichi

2017-02-01

Basaltic volcanoes transfer volatiles from the mantle to the surface of the Earth. The quantification of deep volatile fluxes relies heavily on estimates of the volatile content of primitive magmas, the best archive of which is provided by melt inclusions. Available data from volcanoes producing mafic alkaline lavas in a range of tectonic settings suggest high volatile fluxes, but information remains sparse, particularly for intraplate ocean islands. Here we present measurements of volatile and trace element concentrations, as well as sulphur speciation, in olivine-hosted melt inclusions and matrix glasses from quenched basanite lava balloon samples from the 2011-2012 submarine eruption at El Hierro, Canary Islands. The results reveal remarkably high concentrations of dissolved volatiles and incompatible trace elements in this magma, with ∼80 ppm Nb and up to 3420 ppm CO2, 3.0 wt.% H2O and 5080 ppm S. Reconstructed primitive CO2 contents, considering CO2/Nb systematics and possible CO2 sequestration in shrinkage bubbles, reach weight percent levels, indicating that carbon is a major constituent of Canary Island magmas at depth and that exsolution of a CO2-rich fluid begins in the mantle at pressures in excess of 1 GPa. Correlations between sulphur concentration, sulphur speciation and water content suggest strong reduction of an initially oxidised mantle magma, likely controlled by coupled H2O and S degassing. This late-stage redox change may have triggered sulphide saturation, recorded by globular sulphide inclusions in clinopyroxene and ulvöspinel. The El Hierro basanite thus had a particularly high volatile-carrying capacity and released a minimum of 1.3-2.1 Tg CO2 and 1.8-2.9 Tg S to the environment, causing substantial stress on the local submarine ecosystem. These results highlight the important contribution of alkaline ocean island volcanoes, such as the Canary Islands, to volatile fluxes from the mantle.

Sulphur Mustard Poisoning and Its Complications in Iranian Veterans

Directory of Open Access Journals (Sweden)

Beeta Balali-Mood

2009-09-01

Full Text Available Sulphur mustard is a chemical warfare agent, which was largelyused during the World War One and in Iraq-Iran conflict. It mayalso be used as a chemical terrorism agent. Therefore, medicalprofessions should have sufficient knowledge and be preparedfor medical intervention of any such chemical attack.Sulphur mustard exerts direct toxic effects on the eyes, skin,and respiratory tract, with subsequent systemic actions on thenervous, immunologic, hematologic, digestive, and reproductivesystems. It is an alkylating agent that affects DNA synthesis andthus, delayed complications have been considered since theWorld War One. Cases of malignancies in the target organs particularlyin hematopoietic, respiratory, and digestive systemswere reported. Common delayed respiratory complications includechronic bronchitis, bronchiectasis, frequent bronchopneumonia,and pulmonary fibrosis, all of which tend to deterioratewith time. Severe dry skin, delayed keratitis, and reduction ofnatural killer cells with subsequent increased risk of infectionsand malignancies are also among the most distressing long-termconsequences of sulphur mustard intoxication. However, despiteextensive research that has been conducted on Iranian veteransduring the past decades, major gaps continue to remain in thesulphur mustard literature. Immunological and neurological dysfunctionsand the relationship between exposure to sulphur mustardand mutagenicity, carcinogenicity, and teratogenicity areimportant fields that require further studies, particularly on Iranianveterans with chronic health problems caused by sulphurmustard poisoning. There is also a paucity of information on themedical management of acute and delayed toxic effects of sulphurmustard poisoning, a subject that greatly challenges themedical professions.

Investigations of the changes in the bentonite structure caused by the different treatments

OpenAIRE

Stojiljković S.; Stamenković M.; Kostić D.; Miljković M.; Arsić B.; Savić I.; Savić I.

2015-01-01

The bentonite was treated in different ways and the changes in structure were monitored. Acid activation with sulphuric acid of investigated bentonite caused the increase in specific volume of micropore-mesopore. It was shown that activation by acid obtained at a constant temperature and constant period of time provides the possibility to obtain samples of bentonite of searched porosity only by changing the concentration of sulphuric and hydrochloric acid. ...

STUDIES OF METHOD FOR DETERMINING THE PROTEIN CONCENTRATION OF "MALEIN PPD" BY THE KJELDAHL METHOD

Directory of Open Access Journals (Sweden)

Ciuca, V

2017-06-01

Full Text Available Glanders is a contagious and fatal disease of horses, donkeys, and mules, caused by infection with the bacterium Burkholderia mallei. The pathogen causes nodules and ulcerations in the upper respiratory tract and lungs. Glanders is transmissible to humans by direct contact with diseased animals or with infected or contaminated material. In the untreated acute disease, the mortality rate can reach 95% within 3 weeks Malein PPD - the diagnostic product contain max 2mg/ml Burkholderia mallei. The amount of protein in the biological product "Malein PPD" is measured as nitrogen from protein molecule, applying the Kjeldahl (method determination of nitrogen by sulphuric acid digestion. The validation study aims to demonstrate the determination of the protein of the Malein PPD, by sulphuric acid digestion, it is an appropriate analytical method, reproducible and meets the quality requirements of diagnostic reagents. The paper establishes the performance characteristics of the method considered and identify the factors that influence these characteristics. The method for determining the concentration of protein, by the Kjeldahl method is considered valid if the results obtained for each validation parameter are within the admissibility criteria.The validation procedure includes details on protocol working to determine the protein of the Malein PPD, validation criteria, experimental results, mathematical calculations.

assessment of acidity levels in eucalyptus camaldulensis barks from ...

African Journals Online (AJOL)

BARTH EKWUEME

Bark samples of Eucalyptus camaldulensis obtained from Bauchi and Gombe States were analysed spectrophotometrically for their sulphate-sulphur content. The aim was to assess the extent of sulphur pollution in the environment. The results showed that S concentration ranged from 0.79 to 1.70mg/g for samples from ...

Growth and yield response of sunflower (helianthus annuus l.) to sulphur and boron application

International Nuclear Information System (INIS)

Tahir, M.; Shah, S.A.; Tanveer, A.; Rehman, H.U.

2014-01-01

An experiment was conducted to study the growth and yield response of sunflower to sulphur and boron application. Sulphur (control, 15, 30 kg/ha) and foliar sprays of 1% boron solution (control, spray at 4 week after emergence, 20 days after first spray, at 4 weeks after germination + 20 days after first spray) was applied in soil. The results showed significant increase of all growth and yield parameters by varying levels of sulphur and boron application. Application of 30 kg sulphur/ha enhanced stem diameter (1.99 cm), number of achene per head (765.75) and oil content (36.42%). In case of combined use of sulphur and boron application, maximum plant height (171 cm), head diameter (20.71 cm), 1000-achene weight (54.56 g), biological yield (16.49 t/ha) and achene yield (3.99 t/ha) was recorded by the application of 2 sprays of boron solution (1%) at 4 weeks after germination and reproductive stage. (author)

Chemical and isotopic characteristics of geothermal fluids from Sulphur Springs, Saint Lucia

Science.gov (United States)

Joseph, Erouscilla P.; Fournier, Nicolas; Lindsay, Jan M.; Robertson, Richard; Beckles, Denise M.

2013-03-01

Sulphur Springs is a vigorous, geothermal field associated with the active Soufrière Volcanic Centre in southern Saint Lucia, Lesser Antilles island arc. The 'Sulphur Springs Park' is an important tourist attraction (touted as the 'world's only drive-through volcano') with some of the hot pools being developed into recreational pools. Some 200,000 people visit the park each year. Since 2001, the hydrothermal fluids of Sulphur Springs have been sampled as part of an integrated volcanic monitoring programme for the island. Gas and water samples were analysed to characterise the geochemistry of the hydrothermal system, and to assess the equilibrium state and subsurface temperatures of the reservoir. This has also enabled us, for the first time, to establish baseline data for future geochemical monitoring. The gases are of typical arc-type composition, with N2 excess and low He and Ar content. The dry gas composition is dominated by CO2 (ranging from 601-993 mmol/mol), with deeper magmatic sourced H2S-rich vapour undergoing boiling and redox changes in the geothermal reservoir to emerge with a hydrothermal signature in the fumarolic gases. Fluid contributions from magmatic degassing are also evident, mainly from the moderate to high contents of HCl and deeply-sourced H2S gas, respectively. Sulphur Springs hydrothermal waters have acid-sulphate type compositions (SO4 = 78-4008 mg/L; pH = 3-7), and are of primarily meteoric origin which have been affected by evaporation processes based on the enrichment in both δ18O and δD (δ18O = - 1 to 15‰ and δD = - 9 to 14‰ respectively) in relation to the global meteoric water line (GMWL). These waters are steam-heated water typically formed by absorption of H2S-rich gases in the near surface oxygenated groundwaters. Reservoir temperatures calculated from the evaluation of gas equilibria in the CO2-CH4-H2 system reveal higher temperatures (190 to 300 °C) than those derived from quartz geothermometry (95 to 169 °C), which

Sulphur isotopes in a metamorphogenic gold deposit, Macraes mine, Otago Schist, New Zealand

International Nuclear Information System (INIS)

Craw, D.; Hall, A.J.; Fallick, A.E.; Boyce, A.J.

1995-01-01

The Macraes gold quartz vein deposit, New Zealand, is located in a shear zone cutting greenschist facies metasediments of the Otago Schist. The deposit has been interpreted as being metamorphogenic in origin as there is no evidence for coeval magmatic activity in the Otago Schist orogen. The immediate host rock at the Macraes deposit is pyritic (δ 34 S = -2.7 to -1.3 per mil ) and locally weakly graphitic schist, a rare rock type in the Otago Schist. Sulphur isotope analyses of pyrite and arsenopyrite extracts from auriferous veins and wall-rock schist provide a similar narrow range in δ 34 S values, from -3.0 to -1.0 per mil (n=9). The lack of isotopically depleted sulphur, the narrow range in values, and the replacement sulphide textures help discount a primary bacteriogenic origin for host-rock sulphide. Sulphide in both veins and wall rock is of hydrothermal origin. Sulphides in metasediments and metavolcanics elsewhere in the Otago Schist have δ 34 S in the narrow range -6 to +6 per mil. The sulphur isotope data are consistent with origin of hydrothermal sulphur within the metamorphic pile but provide no constraint on specific rock types which contributed the sulphur to the hydrothermal fluid. The study demonstrates that sulphur isotopic signatures near zero per mil can arise without any direct magmatic input into the mineralisation process. (author). 34 refs., 2 figs., 1 tab

Origin of organic sulphur compounds and sulphur-containing high molecular weight substances in sediments and immature crude oils

NARCIS (Netherlands)

Sinninghe Damsté, J.S.; Rijpstra, W.I.C.; Leeuw, J.W. de; Schenck, P.A.

1988-01-01

The distribution patterns of Organic Sulphur Compounds (OSC), occurring in certain sediments and immature crude oils, were compared with those of the corresponding hydrocarbons. Because of the complexity of the OSC mixtures, they were desulphurized to hydrocarbons (n-alkanes, isoprenoid alkanes,

Inhibition of fatty acid mobilization by arterial free fatty acid concentration

DEFF Research Database (Denmark)

Madsen, J; Bülow, J; Nielsen, N E

1986-01-01

Subcutaneous, inguinal adipose tissue from dogs was perfused with blood in which the free fatty acid (FFA) concentration was varied corresponding to FFA/albumin molar ratios between 1 and 6. Otherwise the composition of the perfusate was kept constant. In order to stimulate lipolysis, isoprenaline...

Modified sulphur cement: A low porosity encapsulation material for low, medium and alpha waste

International Nuclear Information System (INIS)

Dalen, A. van; Rijpkema, J.E.

1989-01-01

Modified sulphur cement, available under the trade name Chement 2000, is a thermoplastic candidate material for the matrix of low, intermediate and alpha radioactive waste. The main source of sulphur is the desulphurization of fossil fuels. In view of the future increase of this product a modified compound of sulphur has been developed at the US Bureau of Mines. Modified sulphur cement as matrix material has properties in common with Portland or blast furnace cement and bitumen. The mechanical strength is comparable to hydraulic cement products. The process to incorporate waste materials is identical to bitumization. The leachability and the resistance to attack by chemicals is nearly the same as for bituminized products. This study showed also that the radiation resistance is high without radiolytic gas production and without change in dimensions (swelling). The rigidity of the matrix is a disadvantage when internal pressures are built up. The thermal conductivity and the heat of combustion of sulphur is low resulting in slow damage to the waste form under fire conditions, even when the temperature of self ignition in air is 220 0 C. The low leachability, the very slow effective diffusion of H 2 O and HTO, and the low permeability is due to the small pore diameters in the modified sulphur matrix. The loading capacity of modified sulphur cement depends on grain size and distribution and is for ungraded ashes, precipitates, dried sludges, etc., in the order of 40-50% of weight. The price of Chement 2000 per tonne is equal to those of blown bitumen

Feasibility of high-resolution continuum source molecular absorption spectrometry in flame and furnace for sulphur determination in petroleum products

Science.gov (United States)

Kowalewska, Zofia

2011-07-01

For the first time, high-resolution molecular absorption spectrometry with a high-intensity xenon lamp as radiation source has been applied for the determination of sulphur in crude oil and petroleum products. The samples were analysed as xylene solutions using vaporisation in acetylene-air flame or in an electrothermally heated graphite furnace. The sensitive rotational lines of the CS molecule, belonging to the ∆ν = 0 vibrational sequence within the electronic transition X 1∑ + → A 1П, were applied. For graphite furnace molecular absorption spectrometry, the Pd + Mg organic modifier was selected. Strong interactions with Pd atoms enable easier decomposition of sulphur-containing compounds, likely through the temporal formation of Pd xS y molecules. At the 258.056 nm line, with the wavelength range covering central pixel ± 5 pixels and with application of interactive background correction, the detection limit was 14 ng in graphite furnace molecular absorption spectrometry and 18 mg kg -1 in flame molecular absorption spectrometry. Meanwhile, application of 2-points background correction found a characteristic mass of 12 ng in graphite furnace molecular absorption spectrometry and a characteristic concentration of 104 mg kg -1 in flame molecular absorption spectrometry. The range of application of the proposed methods turned out to be significantly limited by the properties of the sulphur compounds of interest. In the case of volatile sulphur compounds, which can be present in light petroleum products, severe difficulties were encountered. On the contrary, heavy oils and residues from distillation as well as crude oil could be analysed using both flame and graphite furnace vaporisation. The good accuracy of the proposed methods for these samples was confirmed by their mutual consistency and the results from analysis of reference samples (certified reference materials and home reference materials with sulphur content determined by X-ray fluorescence

Feasibility of high-resolution continuum source molecular absorption spectrometry in flame and furnace for sulphur determination in petroleum products

Energy Technology Data Exchange (ETDEWEB)

Kowalewska, Zofia, E-mail: zofia.kowalewska@obr.pl

2011-07-15

For the first time, high-resolution molecular absorption spectrometry with a high-intensity xenon lamp as radiation source has been applied for the determination of sulphur in crude oil and petroleum products. The samples were analysed as xylene solutions using vaporisation in acetylene-air flame or in an electrothermally heated graphite furnace. The sensitive rotational lines of the CS molecule, belonging to the {Delta}{nu} = 0 vibrational sequence within the electronic transition X{sup 1}{Sigma}{sup +} {yields} A{sup 1}{Pi}, were applied. For graphite furnace molecular absorption spectrometry, the Pd + Mg organic modifier was selected. Strong interactions with Pd atoms enable easier decomposition of sulphur-containing compounds, likely through the temporal formation of Pd{sub x}S{sub y} molecules. At the 258.056 nm line, with the wavelength range covering central pixel {+-} 5 pixels and with application of interactive background correction, the detection limit was 14 ng in graphite furnace molecular absorption spectrometry and 18 mg kg{sup -1} in flame molecular absorption spectrometry. Meanwhile, application of 2-points background correction found a characteristic mass of 12 ng in graphite furnace molecular absorption spectrometry and a characteristic concentration of 104 mg kg{sup -1} in flame molecular absorption spectrometry. The range of application of the proposed methods turned out to be significantly limited by the properties of the sulphur compounds of interest. In the case of volatile sulphur compounds, which can be present in light petroleum products, severe difficulties were encountered. On the contrary, heavy oils and residues from distillation as well as crude oil could be analysed using both flame and graphite furnace vaporisation. The good accuracy of the proposed methods for these samples was confirmed by their mutual consistency and the results from analysis of reference samples (certified reference materials and home reference materials with

Airborne Precursors Predict Maternal Serum Perfluoroalkyl Acid Concentrations.

Science.gov (United States)

Makey, Colleen M; Webster, Thomas F; Martin, Jonathan W; Shoeib, Mahiba; Harner, Tom; Dix-Cooper, Linda; Webster, Glenys M

2017-07-05

Human exposure to persistent perfluoroalkyl acids (PFAAs), including perfluorooctanoic acid (PFOA), perfluorononanoic acid (PFNA), and perfluorooctanesulfonate (PFOS), can occur directly from contaminated food, water, air, and dust. However, precursors to PFAAs (PreFAAs), such as dipolyfluoroalkyl phosphates (diPAPs), fluorotelomer alcohols (FTOHs), perfluorooctyl sulfonamides (FOSAs), and sulfonamidoethanols (FOSEs), which can be biotransformed to PFAAs, may also be a source of exposure. PFAAs were analyzed in 50 maternal sera samples collected in 2007-2008 from participants in Vancouver, Canada, while PFAAs and PreFAAs were measured in matching samples of residential bedroom air collected by passive sampler and in sieved vacuum dust (<150 μm). Concentrations of PreFAAs were higher than for PFAAs in air and dust. Positive associations were discovered between airborne 10:2 FTOH and serum PFOA and PFNA and between airborne MeFOSE and serum PFOS. On average, serum PFOS concentrations were 2.3 ng/mL (95%CI: 0.40, 4.3) higher in participants with airborne MeFOSE concentrations in the highest tertile relative to the lowest tertile. Among all PFAAs, only PFNA in air and vacuum dust predicted serum PFNA. Results suggest that airborne PFAA precursors were a source of PFOA, PFNA, and PFOS exposure in this population.

Fasting plasma chenodeoxycholic acid and cholic acid concentrations are inversely correlated with insulin sensitivity in adults

Directory of Open Access Journals (Sweden)

Laville Martine

2011-07-01

Full Text Available Abstract Background Accumulating data suggest a novel role for bile acids (BAs in modulating metabolic homeostasis. BA treatment has been shown to improve glucose tolerance and to increase energy expenditure in mice. Here, we investigated the relationship between fasting plasma BAs concentrations and metabolic parameters in humans. Findings Fasting plasma glucose, insulin and lipid profile were measured in 14 healthy volunteers, 20 patients with type 2 diabetes (T2D, and 22 non-diabetic abdominally obese subjects. Insulin sensitivity was also assessed by the determination of the glucose infusion rate (GIR during a hyperinsulinemic-euglycemic clamp in a subgroup of patients (9 healthy and 16 T2D subjects. Energy expenditure was measured by indirect calorimetry. Plasma cholic acid (CA, chenodeoxycholic acid (CDCA and deoxycholic acid (DCA concentrations were analyzed by gas chromatograph-mass spectrometry. In univariable analysis, a positive association was found between HOMA-IR and plasma CDCA (β = 0.09, p = 0.001, CA (β = 0.03, p = 0.09 and DCA concentrations (β = 0.07, p Conclusions Both plasma CDCA, CA and DCA concentrations were negatively associated with insulin sensitivity in a wide range of subjects.

Forced swimming and imipramine modify plasma and brain amino acid concentrations in mice.

Science.gov (United States)

Murakami, Tatsuro; Yamane, Haruka; Tomonaga, Shozo; Furuse, Mitsuhiro

2009-01-05

The relationships between monoamine metabolism and forced swimming or antidepressants have been well studied, however information is lacking regarding amino acid metabolism under these conditions. Therefore, the aim of the present study was to investigate the effects of forced swimming and imipramine on amino acid concentrations in plasma, the cerebral cortex and the hypothalamus in mice. Forced swimming caused cerebral cortex concentrations of L-glutamine, L-alanine, and taurine to be increased, while imipramine treatment caused decreased concentrations of L-glutamate, L-alanine, L-tyrosine, L-methionine, and L-ornithine. In the hypothalamus, forced swimming decreased the concentration of L-serine while imipramine treatment caused increased concentration of beta-alanine. Forced swimming caused increased plasma concentration of taurine, while concentrations of L-serine, L-asparagine, L-glutamine and beta-alanine were decreased. Imipramine treatment caused increased plasma concentration of all amino acid, except for L-aspartate and taurine. In conclusion, forced swimming and imipramine treatment modify central and peripheral amino acid metabolism. These results may aid in the identification of amino acids that have antidepressant-like effects, or may help to refine the dosages of antidepressant drugs.

Relations between fatty acid synthesis, pyruvate concentration and cell concentration of suspensions of isolated rat hepatocytes

NARCIS (Netherlands)

Beynen, A.C.; Geelen, M.J.H.

1984-01-01

1. 1. The cell concentration of suspensions of isolated rat hepatocytes affects both the rate of pyruvate accumulation in the incubation medium and the rate of fatty acid synthesis. 2. 2. At low cell concentrations pyruvate accumulation is directly related to the cell concentration but levels off

Metabolic syndrome, alcohol consumption and genetic factors are associated with serum uric acid concentration.

Directory of Open Access Journals (Sweden)

Blanka Stibůrková

Full Text Available Uric acid is the end product of purine metabolism in humans, and increased serum uric acid concentrations lead to gout. The objective of the current study was to identify factors that are independently associated with serum uric acid concentrations in a cohort of Czech control individuals.The cohort consisted of 589 healthy subjects aged 18-65 years. We studied the associations between the serum uric acid concentration and the following: (i demographic, anthropometric and other variables previously reported to be associated with serum uric acid concentrations; (ii the presence of metabolic syndrome and the levels of metabolic syndrome components; and (iii selected genetic variants of the MTHFR (c.665C>T, c.1286A>C, SLC2A9 (c.844G>A, c.881G>A and ABCG2 genes (c.421C>A. A backward model selection procedure was used to build two multiple linear regression models; in the second model, the number of metabolic syndrome criteria that were met replaced the metabolic syndrome-related variables.The models had coefficients of determination of 0.59 and 0.53. The serum uric acid concentration strongly correlated with conventional determinants including male sex, and with metabolic syndrome-related variables. In the simplified second model, the serum uric acid concentration positively correlated with the number of metabolic syndrome criteria that were met, and this model retained the explanatory power of the first model. Moderate wine drinking did not increase serum uric acid concentrations, and the urate transporter ABCG2, unlike MTHFR, was a genetic determinant of serum uric acid concentrations.Metabolic syndrome, moderate wine drinking and the c.421C>A variant in the ABCG gene are independently associated with the serum uric acid concentration. Our model indicates that uric acid should be clinically monitored in persons with metabolic syndrome.

Prediction of sulphur content in the industrial hydrotreatment process

Energy Technology Data Exchange (ETDEWEB)

Lukec, Ivana; Lukec, Darko [Model d.o.o, Pazinska 36, 10110 Zagreb (Croatia); Sertic-Bionda, Katica [Faculty of Chemical Engineering and Technology, Marulicev trg 19, 10000, Zagreb (Croatia)

2008-03-15

The artificial neural network models were developed to determine sulphur content in the hydrotreatment product. Two models for two different types of feed were developed: light gas oil and vacuum gas oil. The developed ANN models use 6 input variables that are continuously measured in the process and are in accordance with the engineering knowledge and thermodynamics of hydrotreatment processes. Given models show good predictability of sulphur content in the hydrotreatment product and are, therefore, used in practice for continuous monitoring and optimization. This kind of application can be easily developed in any other hydrotreatment process with the available adequate historical data. (author)

Effects on grape amino acid concentration through foliar application of three different elicitors.

Science.gov (United States)

Gutiérrez-Gamboa, G; Portu, J; Santamaría, P; López, R; Garde-Cerdán, T

2017-09-01

Elicitors play an important role in the defense against pathogens as an alternative to chemical pesticides by increasing secondary metabolites. Their effect on grape amino acid has been little investigated. Thus, the aim of this research was to study the influence of methyl jasmonate (MeJ), chitosan (CHT), and a yeast extract (YE) on grape amino acid composition, through foliar applications to grapevines. The must amino acid concentration was analyzed by HPLC. The results showed that CHT and YE treatments decreased the must concentration of several amino acids, affecting total amino acid content (from 2364 to 1961, and 1818mg/L, respectively). However, MeJ treatment had a slight effect on grape amino acid content, increasing the concentration of Met (from 8.95 to 12.13mg/L) and Phe (from 7.96 to 9.29mg/L). It seems to be that, the resistance induction through CHT and YE treatments results in physiological costs to grapevines associated with a decrease on grape amino acid concentration. Consequently, MeJ applications, as a viticultural practice, could be a better tool than CHT and YE treatments, because did not affect grape amino acid concentration. Copyright © 2017 Elsevier Ltd. All rights reserved.

Amino Acid Composition of an Organic Brown Rice Protein Concentrate and Isolate Compared to Soy and Whey Concentrates and Isolates.

Science.gov (United States)

Kalman, Douglas S

2014-06-30

A protein concentrate (Oryzatein-80™) and a protein isolate (Oryzatein-90™) from organic whole-grain brown rice were analyzed for their amino acid composition. Two samples from different batches of Oryzatein-90™ and one sample of Oryzatein-80™ were provided by Axiom Foods (Los Angeles, CA, USA). Preparation and analysis was carried out by Covance Laboratories (Madison, WI, USA). After hydrolysis in 6-N hydrochloric acid for 24 h at approximately 110 °C and further chemical stabilization, samples were analyzed by HPLC after pre-injection derivitization. Total amino acid content of both the isolate and the concentrate was approximately 78% by weight with 36% essential amino acids and 18% branched-chain amino acids. These results are similar to the profiles of raw and cooked brown rice except in the case of glutamic acid which was 3% lower in the isolate and concentrate. The amino acid content and profile of the Oryzatein-90™ isolate was similar to published values for soy protein isolate but the total, essential, and branched-chain amino acid content of whey protein isolate was 20%, 39% and 33% greater, respectively, than that of Oryzatein-90™. These results provide a valuable addition to the nutrient database of protein isolates and concentrates from cereal grains.

A novel approach to mitigating sulphur dioxide emissions and producing a mercury sorbent material using oil-sands fluid coke

International Nuclear Information System (INIS)

Morris, E.; Jia, C.Q.; Tong, S.

2008-01-01

Pyrometallurgical smelting operations are a major source of sulphur dioxide (SO 2 ) which is a precursor to acid rain and increased levels of UV-B penetration in boreal lakes. Mercury is also released in copper smelter off-gas, which can bioaccumulate and cause neurological disorders and death in humans. Fluid coke is produced in massive quantities as a by-product of bitumen upgrading at Syncrude Canada's facility in Fort McMurray, Alberta. Oilsands fluid coke can be used to reduce SO 2 and produce elemental sulphur as a co-product. This process was dubbed SOactive. The reaction physically activates the fluid coke to produce a sulphur-impregnated activated carbon (SIAC) which is known as ECOcarbon. Some studies have indicated that SIAC is well suited for the removal of vapour phase mercury, mainly due to the formation of stable mercuric sulphide species. This paper discussed the findings made to date in relation to the SOactive process and the characterization of ECOcarbons. The paper discussed the use of fluid coke for reducing SO 2 emissions while producing elemental sulphur as well as coke-SO 2 -oxygen (O 2 ) and coke-SO 2 -water (H 2 O) systems. The paper also examined the production of SIAC products for use in capturing vapour phase mercury. The paper presented the materials and methodology, including an illustration of the apparatus used in reduction of SO 2 and activation of fluid coke. It was concluded that more work is still needed to analyse the effect of O 2 and SO 2 reduction and SIAC properties under smelter flue gas conditions. 10 refs., 1 tab., 8 figs

Wolframite Conversion in Treating a Mixed Wolframite-Scheelite Concentrate by Sulfuric Acid

Science.gov (United States)

Shen, Leiting; Li, Xiaobin; Zhou, Qiusheng; Peng, Zhihong; Liu, Guihua; Qi, Tiangui; Taskinen, Pekka

2018-02-01

Complete wolframite conversion in sulfuric acid is significant for expanding the applicability of the sulfuric acid method for producing ammonium paratungstate. In this paper, the conversion of wolframite in treating a mixed wolframite-scheelite concentrate by sulfuric acid was studied systematically. The results show that the conversion of wolframite in sulfuric acid is more difficult than that of scheelite, requiring rigorous reaction conditions. A solid H2WO4 layer forms on the surfaces of the wolframite particles and becomes denser with increasing H2SO4 concentration, thus hindering the conversion. Furthermore, the difficulty in wolframite conversion can be mainly attributed to the accumulation of Fe2+ (and/or Mn2+) in the H2SO4 solution, which can be solved by reducing Fe2+ (and/or Mn2+) concentration through oxidization and/or a two-stage process. Additionally, the solid converted product of the mixed wolframite-scheelite concentrate has an excellent leachability of tungsten in an aqueous ammonium carbonate solution at ambient temperature, with approximately 99% WO3 recovery. This work presents a route for manufacturing ammonium paratungstate by treating the mixed concentrate in sulfuric acid followed by leaching in ammonium carbonate solution.

Trend of heavy metal and sulphur deposition in Finland from the 1980`s to 1990`s

Energy Technology Data Exchange (ETDEWEB)

Kubin, E.; Lippo, H. [Forest Research Inst., Muhos (Finland)

1995-12-31

The moss technique to survey atmospheric heavy metal deposition was developed in Sweden in the late 1960`s. The surveys has extended from regional and national basis to cover all the Nordic countries in 1985, to northern Europe in 1990 and to a large part of Europe in 1990-92. National reports have also been published in many countries. The Forest Research Institute established a network of 3009 secret permanent monitoring sites all over the country in 1985 and 1986 for forest inventory and for monitoring the situation and changes in the forests. One essential part has been to study the effects of air pollution - including heavy metal and sulphur deposition on forests. Deposition has been monitored by collecting bioindicators and analysing the element concentrations. The purpose of this report is to show the trend of the heavy metal and sulphur deposition from the 1980`s to 1990`s and in addition to produce information about the emission sources. (author)

Trend of heavy metal and sulphur deposition in Finland from the 1980`s to 1990`s

Energy Technology Data Exchange (ETDEWEB)

Kubin, E; Lippo, H [Forest Research Inst., Muhos (Finland)

1996-12-31

The moss technique to survey atmospheric heavy metal deposition was developed in Sweden in the late 1960`s. The surveys has extended from regional and national basis to cover all the Nordic countries in 1985, to northern Europe in 1990 and to a large part of Europe in 1990-92. National reports have also been published in many countries. The Forest Research Institute established a network of 3009 secret permanent monitoring sites all over the country in 1985 and 1986 for forest inventory and for monitoring the situation and changes in the forests. One essential part has been to study the effects of air pollution - including heavy metal and sulphur deposition on forests. Deposition has been monitored by collecting bioindicators and analysing the element concentrations. The purpose of this report is to show the trend of the heavy metal and sulphur deposition from the 1980`s to 1990`s and in addition to produce information about the emission sources. (author)

Effect of postreatment on the corrosion behaviour of tartaric-sulphuric anodic films

Energy Technology Data Exchange (ETDEWEB)

Garcia-Rubio, M. [Departamento de Quimica-Fisica Aplicada, Universidad Autonoma de Madrid, 28049 Madrid (Spain); Department of Surface Technologies, Engineering of Materials and Processes, Airbus Spain, Av. John Lennon s/n 28906 Getafe (Spain); Lara, M.P. de [Departamento de Quimica-Fisica Aplicada, Universidad Autonoma de Madrid, 28049 Madrid (Spain); Ocon, P. [Departamento de Quimica-Fisica Aplicada, Universidad Autonoma de Madrid, 28049 Madrid (Spain)], E-mail: pilar.ocon@uam.es; Diekhoff, S. [Fraunhofer-IFAM, Lesumer Heerstrasse 36, 28717 Bremen (Germany); Beneke, M. [Department of Surface Technologies, Engineering of Materials and Processes, Airbus Deutschland, GmbH Hunefeldstr. 1-5, 28199 Bremen (Germany); Lavia, A.; Garcia, I. [Department of Surface Technologies, Engineering of Materials and Processes, Airbus Spain, Av. John Lennon s/n 28906 Getafe (Spain)

2009-08-30

Unclad and clad AA2024 T3 specimens were anodised in a chromium-free tartaric-sulphuric acid bath (TSA) and subsequently postreated by different processes including impregnation in a cold, concentrated chromate solution, Cr-free hot-water sealing, and dichromate hot-water sealing. The purpose of this work is to evaluate the effectiveness of the classical postreatments used in the aircraft industry on the TSA-anodic films and their corrosion resistance behaviour. TSA-anodic films were characterised by scanning electron microscopy (SEM) and their thicknesses were measured by SEM and the eddy current method. Electrochemical impedance spectroscopy (EIS) was used to characterise the barrier and porous layers, and jointly with potentiodynamic polarisation allowed the evaluation of corrosion resistance parameters with immersion time in NaCl solution for anodised and postreated specimens. In all cases the postreatments increased the resistance of the barrier layer against degradation. However, the NaCl electrolyte easily penetrated TSA-anodised porous layers when they were not postreated, while penetration was slightly more difficult in cold-postreated specimens. The effective pore plugging was observed in the sealed TSA specimens resulting in an improved corrosion resistance. On the other hand, unsealed clad AA2024 specimens showed a self-sealing process of the TSA-anodic layer, which was slower for the cold chromate solution-postreated specimens.

Effect of postreatment on the corrosion behaviour of tartaric-sulphuric anodic films

International Nuclear Information System (INIS)

Garcia-Rubio, M.; Lara, M.P. de; Ocon, P.; Diekhoff, S.; Beneke, M.; Lavia, A.; Garcia, I.

2009-01-01

Unclad and clad AA2024 T3 specimens were anodised in a chromium-free tartaric-sulphuric acid bath (TSA) and subsequently postreated by different processes including impregnation in a cold, concentrated chromate solution, Cr-free hot-water sealing, and dichromate hot-water sealing. The purpose of this work is to evaluate the effectiveness of the classical postreatments used in the aircraft industry on the TSA-anodic films and their corrosion resistance behaviour. TSA-anodic films were characterised by scanning electron microscopy (SEM) and their thicknesses were measured by SEM and the eddy current method. Electrochemical impedance spectroscopy (EIS) was used to characterise the barrier and porous layers, and jointly with potentiodynamic polarisation allowed the evaluation of corrosion resistance parameters with immersion time in NaCl solution for anodised and postreated specimens. In all cases the postreatments increased the resistance of the barrier layer against degradation. However, the NaCl electrolyte easily penetrated TSA-anodised porous layers when they were not postreated, while penetration was slightly more difficult in cold-postreated specimens. The effective pore plugging was observed in the sealed TSA specimens resulting in an improved corrosion resistance. On the other hand, unsealed clad AA2024 specimens showed a self-sealing process of the TSA-anodic layer, which was slower for the cold chromate solution-postreated specimens.

Sources of atmospheric acidity

International Nuclear Information System (INIS)

Clarke, A.G.

1992-01-01

The emissions of acid gases from anthropogenic sources and their impact on the environment are the main concern of this book. However, that impact can only be assessed if all the naturally occurring sources of these gases are also known and can be quantified. Given the widely dispersed nature of the natural sources and the problems of measurement of trace species at low concentrations, often in remote regions, the quantification is a very difficult task. Nevertheless, considerable progress has been made over the last decade. In this chapter both man-made and natural sources of atmospheric acidity will be reviewed, but the emphasis will be placed not so much on the global balances as on the scale of the natural sources in relation to the man-made sources. This requires that the very uneven geographical distribution of emissions and the lifetime of individual chemical species be taken into account. The emissions considered are sulphur compounds, nitrogen compounds, chlorine compounds and organic acids. The anthropogenic sources discussed are the combustion of fossil fuels and certain industrial processes. Emissions data for anthropogenic sources are given for the United Kingdom, Europe, USA and globally. A list of 95 references is given. (Author)

WATER PINCH TECHNOLOGY APPLICATION TO MINIMIZE SULPHUROUS WASTEWATER IN AN OIL REFINERY

Directory of Open Access Journals (Sweden)

Gabriel Orlando Lobelles Sardiñas

2017-01-01

Full Text Available In oil refining industries there is a high water consumption, which influences the high production costs and impacts the environment due to the discharge of their wastes. It is known that there are no technological conditions for the reuse of industrial water at the oil refineries, based on hydroskimming processes. The objective of this study is to implement the process integration methodology, Water Pinch, to a sour water stripper unit, as a unitary process of an oil refinery, to minimize the amount of sulphurous waste water and reduce contamination of the bay that receives these wastes. The technology is applied to evaluate the volume of sulphurous wastewater generated in the Cienfuegos oil refinery. This technology allows identifying opportunities for recovery and reuse of water, based on concentration ranges of contaminants. To achieve this purpose, a sour water stripper tower was assessed with the help of Water Pinch software, which provided an optimized distribution network, as a proposed technological improvement. This facilitated to recover and reuse 667 757, 28 m3 of water per year, and 1 035 023, 78 CUC were saved, at the same time the amount of polluting effluents decreased in approximately 2 % of non-reusable treated water.

Nitrogen balance, plasma free amino acid concentrations and urinary orotic acid excretion during long-term fasting in cats.

Science.gov (United States)

Biourge, V; Groff, J M; Fisher, C; Bee, D; Morris, J G; Rogers, Q R

1994-07-01

The purpose of this study was to ascertain the changes in nitrogen balance, plasma free amino acid concentrations, urinary orotic acid excretion and body weight during long-term fasting in adult obese cats. Results from eight cats that fasted rather than eat an unpalatable diet are reported. After 5 to 6 wk of weight loss, six of the eight cats developed signs of hepatic lipidosis, and the livers of all cats were severely infiltrated with lipids. Cats lost (mean +/- SE) 33.2 +/- 1.4% of their pre-fasting body weight. Mean nitrogen balance (+/- SE) was -547 +/- 54 mg.d-1.kg-2/3 for the first week, and then the net nitrogen losses decreased to a plateau (-303 +/- 52 mg.d-1.kg-2/3) after 4 wk. Fasting was associated with a decrease in plasma concentration of essential amino acids. When plasma amino acid concentrations were considered individually, concentrations of alanine, methionine, taurine, citrulline, arginine and tryptophan decreased the most (> or = 50%), whereas concentrations of glutamine, glutamate and ornithine significantly increased. Orotic acid was not detected in the urine during the fast. After 1 wk of fasting, obese cats had reduced nitrogen excretion, but not to the same extent as has been shown in obese humans or obese rats. It is suggested that the availability of several amino acids may become limiting for liver protein synthesis during fasting and that these deficiencies may contribute to the development of hepatic lipidosis. Orotic acid was not linked to hepatic lipidosis caused by fasting in cats.

Studies on the availability of sulphur in four soil series of soil and water management project, Patiala

International Nuclear Information System (INIS)

Sharma, Kesho Ram; Dev, G.

1974-01-01

Differential behaviour of four soils series (Banra, Fatehpur, Temple and Samana) for availability of S to wheat (Kalyan-sona) was studied in a pot experiment using five doses of labelled sulphur (0, 5, 10, 20 and 40 kg/ha) applied as (NH 4 ) 2 35 SO 4 . The yield, sulphur content and total removal of sulphur by plant, was found dependent upon sulphur supplying power of the soil, which was confirmed by the radioassay data as well. (author)

Discharging a Li-S battery with ultra-high sulphur content cathode using a redox mediator.

Science.gov (United States)

Kim, Kwi Ryong; Lee, Kug-Seung; Ahn, Chi-Yeong; Yu, Seung-Ho; Sung, Yung-Eun

2016-08-30

Lithium-sulphur batteries are under intense research due to the high specific capacity and low cost. However, several problems limit their commercialization. One of them is the insulating nature of sulphur, which necessitates a large amount of conductive agent and binder in the cathode, reducing the effective sulphur load as well as the energy density. Here we introduce a redox mediator, cobaltocene, which acts as an electron transfer agent between the conductive surface and the polysulphides in the electrolyte. We confirmed that cobaltocene could effectively convert polysulphides to Li2S using scanning electron microscope, X-ray absorption near-edge structure and in-situ X-ray diffraction studies. This redox mediator enabled excellent electrochemical performance in a cathode with ultra-high sulphur content (80 wt%). It delivered 400 mAh g(-1)cathode capacity after 50 cycles, which is equivalent to 800 mAh g(-1)S in a typical cathode with 50 wt% sulphur. Furthermore, the volumetric capacity was also dramatically improved.

Utilización de azufre micronizado en la corrección del pH de compost de residuos de poda Correction of the pH of pruning waste compost with micronized sulphur

Directory of Open Access Journals (Sweden)

L.A. Barbaro

2010-12-01

Full Text Available Los compost actualmente son muy utilizados como componentes de sustratos, aunque en algunos casos presentan pH alcalinos y causan problemas nutricionales. Por ello se recomienda hacer una corrección previa a su utilización o luego de elaborar el sustrato. Algunas alternativas para bajar el pH es mezclando el compost con materiales ácidos o mediante la adición de azufre, sulfato ferroso u otros compuestos azufrados. El objetivo de este trabajo fue corregir el pH de un compost de residuos de poda con azufre micronizado y hallar la dosis adecuada para el pH deseado. Se conformaron siete tratamientos, incorporando al compost de poda diferentes dosis de azufre micronizado: 0, 1, 2, 3, 4, 6 y 8 g/litro. Al compost de cada tratamiento se le midió el pH semanalmente y una vez estabilizados se analizó la conductividad eléctrica, concentración de nitrato, calcio, magnesio, potasio y sodio. Para un pH entre 5,3 y 6,2 se necesitaron 2 a 3 g de azufre/litro. El pH del compost disminuyó con el incremento de la dosis de azufre, y la CE aumentó. El azufre micronizado es una alternativa viable para corregir el pH del compost de restos de poda a los valores deseados.Nowadays, composts are widely used for incorporation into substrates and in some cases they present alkaline pH, causing nutritional problems. Therefore, it is suggested that a correction should be made prior to its use or after its preparation. Some alternatives to decrease pH values are mixing compost with acid materials or adding sulphur, ferrous sulphate or other sulphur compounds. The aim of this work was to correct the pH of pruning waste compost with micronized sulphur and find the appropriate dose for the desired pH. Seven treatments were performed incorporating different doses of micronized sulphur: 0, 1, 2, 3, 4, 6 and 8 g per liter of compost. Compost pH was measured weekly in each treatment. Once stabilized, electrical conductivity and concentration of nitrate, calcium, magnesium

Circadian changes in endogenous concentrations of indole-3-acetic acid, melatonin, serotonin, abscisic acid and jasmonic acid in Characeae (Chara australis Brown).

Science.gov (United States)

Beilby, Mary J; Turi, Christina E; Baker, Teesha C; Tymm, Fiona Jm; Murch, Susan J

2015-01-01

Giant-celled Characeae (Chara australis Brown), grown for 4 months on 12/12 hr day/night cycle and summer/autumn temperatures, exhibited distinct concentration maxima in auxin (indole-3-acetic acid; IAA), melatonin and serotonin about 4 hr after subjective daybreak. These concentration peaks persisted after 3 day pretreatment in continuous darkness: confirming a circadian rhythm, rather than a response to "light on." The plants pretreated for 3 d in continuous light exhibited several large IAA concentration maxima throughout the 24 hr. The melatonin and serotonin concentrations decreased and were less synchronized with IAA. Chara plants grown on 9/15 hr day/night cycle for 4 months and winter/spring temperatures contained much smaller concentrations of IAA, melatonin and serotonin. The IAA concentration maxima were observed in subjective dark phase. Serotonin concentration peaks were weakly correlated with those of IAA. Melatonin concentration was low and mostly independent of circadian cycle. The "dark" IAA concentration peaks persisted in plants treated for 3 d in the dark. The plants pretreated for 3 d in the light again developed more IAA concentration peaks. In this case the concentration maxima in melatonin and serotonin became more synchronous with those in IAA. The abscisic acid (ABA) and jasmonic acid (JA) concentrations were also measured in plants on winter regime. The ABA concentration did not exhibit circadian pattern, while JA concentration peaks were out of phase with those of IAA. The data are discussed in terms of crosstalk between metabolic pathways.

The separation of sulphur-35 and phosphorus-32 from urine and their subsequent estimation

International Nuclear Information System (INIS)

Kramer, G.H.

1981-07-01

A method has been developed that will specifically separate sulphur-35 and phosphorus-32 from urine. Interfering cations are removed by cation exchange and differential precipitation is used to remove the unwanted anion(s). The anion of interest is estimated by liquid scintillation counting and recoveries are 95% for sulphur-35 and 70% for phosphorus-32. The detection limits for sulphur-35 and phosphorus-32 are estimated to be 1.5 pCi and 1.3 pCi, respectively (1 pCi = 37 mBq)

Sulphur-oxidizing and sulphate-reducing communities in Brazilian mangrove sediments.

Science.gov (United States)

Varon-Lopez, Maryeimy; Dias, Armando Cavalcante Franco; Fasanella, Cristiane Cipolla; Durrer, Ademir; Melo, Itamar Soares; Kuramae, Eiko Eurya; Andreote, Fernando Dini

2014-03-01

Mangrove soils are anaerobic environments rich in sulphate and organic matter. Although the sulphur cycle is one of the major actors in this ecosystem, little is known regarding the sulphur bacteria communities in mangrove soils. We investigated the abundance, composition and diversity of sulphur-oxidizing (SOB) and sulphate-reducing (SRB) bacteria in sediments from three Brazilian mangrove communities: two contaminated, one with oil (OilMgv) and one with urban waste and sludge (AntMgv), and one pristine (PrsMgv). The community structures were assessed using quantitative real-time polymerase chain reaction (qPCR), polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) and clone libraries, using genes for the enzymes adenosine-5'-phosphosulphate reductase (aprA) and sulphite reductase (Dsr) (dsrB). The abundance for qPCR showed the ratio dsrB/aprA to be variable among mangroves and higher according to the gradient observed for oil contamination in the OilMgv. The PCR-DGGE patterns analysed by Nonmetric Multidimensional Scaling revealed differences among the structures of the three mangrove communities. The clone libraries showed that Betaproteobacteria, Gammaproteobacteria and Deltaproteobacteria were the most abundant groups associated with sulphur cycling in mangrove sediments. We conclude that the microbial SOB and SRB communities in mangrove soils are different in each mangrove forest and that such microbial communities could possibly be used as a proxy for contamination in mangrove forests. © 2013 John Wiley & Sons Ltd and Society for Applied Microbiology.

Amino Acid Composition of an Organic Brown Rice Protein Concentrate and Isolate Compared to Soy and Whey Concentrates and Isolates

Directory of Open Access Journals (Sweden)

Douglas S. Kalman

2014-06-01

Full Text Available A protein concentrate (Oryzatein-80™ and a protein isolate (Oryzatein-90™ from organic whole-grain brown rice were analyzed for their amino acid composition. Two samples from different batches of Oryzatein-90™ and one sample of Oryzatein-80™ were provided by Axiom Foods (Los Angeles, CA, USA. Preparation and analysis was carried out by Covance Laboratories (Madison, WI, USA. After hydrolysis in 6-N hydrochloric acid for 24 h at approximately 110 °C and further chemical stabilization, samples were analyzed by HPLC after pre-injection derivitization. Total amino acid content of both the isolate and the concentrate was approximately 78% by weight with 36% essential amino acids and 18% branched-chain amino acids. These results are similar to the profiles of raw and cooked brown rice except in the case of glutamic acid which was 3% lower in the isolate and concentrate. The amino acid content and profile of the Oryzatein-90™ isolate was similar to published values for soy protein isolate but the total, essential, and branched-chain amino acid content of whey protein isolate was 20%, 39% and 33% greater, respectively, than that of Oryzatein-90™. These results provide a valuable addition to the nutrient database of protein isolates and concentrates from cereal grains.

Adsorption of volatile sulphur compounds onto modified activated carbons: Effect of oxygen functional groups

International Nuclear Information System (INIS)

Vega, Esther; Lemus, Jesús; Anfruns, Alba; Gonzalez-Olmos, Rafael; Palomar, José; Martin, María J.

2013-01-01

Highlights: • HNO 3 oxidation incorporates a higher amount of functionalities than O 3 oxidation. • The loss of porosity is compensated by the massive incorporation of oxygen groups. • HNO 3 oxidation increases OH groups in AC and the ETM and DMS adsorption capacities. • The oxygen functional groups in the AC surface did not affect the DMDS adsorption. • COSMO-RS predicts the important role of OH groups for VSC adsorption. -- Abstract: The effect of physical and chemical properties of activated carbon (AC) on the adsorption of ethyl mercaptan, dimethyl sulphide and dimethyl disulphide was investigated by treating a commercial AC with nitric acid and ozone. The chemical properties of ACs were characterised by temperature programme desorption and X-ray photoelectron spectroscopy. AC treated with nitric acid presented a larger amount of oxygen functional groups than materials oxidised with ozone. This enrichment allowed a significant improvement on adsorption capacities for ethyl mercaptan and dimethyl sulphide but not for dimethyl disulphide. In order to gain a deeper knowledge on the effect of the surface chemistry of AC on the adsorption of volatile sulphur compounds, the quantum-chemical COSMO-RS method was used to simulate the interactions between AC surface groups and the studied volatile sulphur compounds. In agreement with experimental data, this model predicted a greater affinity of dimethyl disulphide towards AC, unaffected by the incorporation of oxygen functional groups in the surface. Moreover, the model pointed out to an increase of the adsorption capacity of AC by the incorporation of hydroxyl functional groups in the case of ethyl mercaptan and dimethyl sulphide due to the hydrogen bond interactions

Adsorption of volatile sulphur compounds onto modified activated carbons: Effect of oxygen functional groups

Energy Technology Data Exchange (ETDEWEB)

Vega, Esther, E-mail: esther@lequia.udg.cat [LEQUIA, Institute of the Environment, University of Girona, Campus Montilivi, Girona, Catalonia E-17071 (Spain); Lemus, Jesús [Universidad de Madrid, Sección de Ingeniería Química, Cantoblanco, Madrid E-28049 (Spain); Anfruns, Alba; Gonzalez-Olmos, Rafael [LEQUIA, Institute of the Environment, University of Girona, Campus Montilivi, Girona, Catalonia E-17071 (Spain); Palomar, José [Universidad de Madrid, Sección de Ingeniería Química, Cantoblanco, Madrid E-28049 (Spain); Martin, María J. [LEQUIA, Institute of the Environment, University of Girona, Campus Montilivi, Girona, Catalonia E-17071 (Spain)

2013-08-15

Highlights: • HNO{sub 3} oxidation incorporates a higher amount of functionalities than O{sub 3} oxidation. • The loss of porosity is compensated by the massive incorporation of oxygen groups. • HNO{sub 3} oxidation increases OH groups in AC and the ETM and DMS adsorption capacities. • The oxygen functional groups in the AC surface did not affect the DMDS adsorption. • COSMO-RS predicts the important role of OH groups for VSC adsorption. -- Abstract: The effect of physical and chemical properties of activated carbon (AC) on the adsorption of ethyl mercaptan, dimethyl sulphide and dimethyl disulphide was investigated by treating a commercial AC with nitric acid and ozone. The chemical properties of ACs were characterised by temperature programme desorption and X-ray photoelectron spectroscopy. AC treated with nitric acid presented a larger amount of oxygen functional groups than materials oxidised with ozone. This enrichment allowed a significant improvement on adsorption capacities for ethyl mercaptan and dimethyl sulphide but not for dimethyl disulphide. In order to gain a deeper knowledge on the effect of the surface chemistry of AC on the adsorption of volatile sulphur compounds, the quantum-chemical COSMO-RS method was used to simulate the interactions between AC surface groups and the studied volatile sulphur compounds. In agreement with experimental data, this model predicted a greater affinity of dimethyl disulphide towards AC, unaffected by the incorporation of oxygen functional groups in the surface. Moreover, the model pointed out to an increase of the adsorption capacity of AC by the incorporation of hydroxyl functional groups in the case of ethyl mercaptan and dimethyl sulphide due to the hydrogen bond interactions.

Tracer-aided studies on the fate and effects of sulphur dioxide in Spinacia oleracea L. and Triticum vulgare. Part of a coordinated programme on isotopic-tracer-aided studies of atmospheric sulphur pollutant - plant interactions

International Nuclear Information System (INIS)

Plesnicar, M.

1982-06-01

Wheat, Triticum vulgare and spinach, Spinacia oleracea plants were exposed to two different concentrations of 35 SO 2 - released by lactic acid from Na 2 35 SO 3 - for 45 minutes, and distribution of radioactivity was studied in leaves, stem and roots. After 24 hours, the specific activity of the leaves of both plants was reduced while that of the roots was increased, suggesting 35 S translocation from leaves to roots. Translocation to the stem and roots of 35 S products was much higher in wheat than in spinach. In leaves of both plant species, ethanol-soluble products were much higher than the ethanol-insoluble fraction during the first 6 hours of exposure. The ethanol-soluble fraction contained sulphate, sulphite and unidentified material. The study suggests that SO 2 is metabolized in preference to endogenous S, that the wheat plant is more susceptible to SO 2 , and that tolerance is related to the capacity of converting SO 2 to sulphate and reducing its further conversion. Uptake of 35 SO 2 by young and old wheat and spinach plants was studied with a view to determining susceptibility to SO 2 exposure as a function of the developmental stage of the plant. In wheat, young plants metabolize endogenous sulphur in preference to absorbed SO 2 while older plants are active in converting absorbed sulphur into organic (ethanol-insoluble) form. In spinach, young plants are more active in transporting 35 S products from leaves to roots and older plants show higher incorporation percentage of 35 S into the organic fraction of leaves. Uptake of 1- 14 C-acetate by lipids of leaf discs from spinach and wheat was investigated in normal and SO 2 -stressed plants. The incorporation of radioacetate into lipids of leaf tissues of both plants was strongly inhibited in SO0 plants. Also U- 14 C-lysine incorporation into proteins of leaf tissue was significantly inhibited by 0.2-2.0 ppm aqueous SO 2

Effects of acid concentration on intramolecular charge transfer ...

Indian Academy of Sciences (India)

rate. Time-dependent density functional theory calculations have been performed to understand the observed spectroscopic results. Keywords. Intramolecular charge transfer; absorption and fluorescence; time resolved fluorescence measurements; acid concentration dependence; time-dependent density functional theory.

The effect of concentration of glycerol and electric current on the morphology and particle size of electrodeposited cadmium powder

Directory of Open Access Journals (Sweden)

S. G. Viswanath

2013-06-01

Full Text Available Cadmium powder was obtained by electrodeposition of cadmium from glycerol and sulphuric acid. The morphology and particle size of these powders were studied. Broken dendrites, intermingled with spongy and irregular particles were observed in the powder. Around 60% of particles were below 100 µm. XRD studies showed that particles with sizes between 212.2 and 303.2 nm were present in the powder. The apparent density of cadmium powder decreased with increase in concentration of glycerol. The stability of the powder and current efficiency were also studied

Rubber composites cured with sulphur and peroxide and ...

Indian Academy of Sciences (India)