Novel bioevaporation process for the zero-discharge treatment of highly concentrated organic wastewater.

Science.gov (United States)

Yang, Benqin; Zhang, Lei; Lee, Yongwoo; Jahng, Deokjin

2013-10-01

A novel process termed as bioevaporation was established to completely evaporate wastewater by metabolic heat released from the aerobic microbial degradation of the organic matters contained in the highly concentrated organic wastewater itself. By adding the glucose solution and ground food waste (FW) into the biodried sludge bed, the activity of the microorganisms in the biodried sludge was stimulated and the water in the glucose solution and FW was evaporated. As the biodegradable volatile solids (BVS) concentration in wastewater increased, more heat was produced and the water removal ratio increased. When the volatile solids (VS) concentrations of both glucose and ground FW were 120 g L(-1), 101.7% and 104.3% of the added water was removed, respectively, by completely consuming the glucose and FW BVS. Therefore, the complete removal of water and biodegradable organic contents was achieved simultaneously in the bioevaporation process, which accomplished zero-discharge treatment of highly concentrated organic wastewater. Copyright © 2013 Elsevier Ltd. All rights reserved.

Latex allergy in the workplace.

Science.gov (United States)

Toraason, M; Sussman, G; Biagini, R; Meade, J; Beezhold, D; Germolec, D

2000-11-01

While less than 1% of the general population is sensitized to latex, the U.S. Occupational Safety and Health Administration estimates that 8-12% of health-care workers are sensitized. The major source of workplace exposure is powdered natural rubber latex (NRL) gloves. NRL is harvested from HEVEA: brasiliensis trees and ammoniated to prevent coagulation resulting in the hydrolysis of the latex proteins. Prior to use in manufacturing, the latex is formulated by the addition of multiple chemicals. Thus, human exposure is to a mixture of residual chemicals and hydrolyzed latex peptides. Clinical manifestations include irritant contact dermatitis, allergic contact dermatitis (type IV), and type I immediate hypersensitivity response. Type I (IgE-mediated) NRL allergy includes contact urticaria, systemic urticaria, angioedema, rhinitis, conjunctivitis, bronchospasm, and anaphylaxis. Taking an accurate history, including questions on atopic status, food allergy, and possible reactions to latex devices makes diagnosis of type-I latex allergy possible. To confirm a diagnosis, either in vivo skin prick testing (SPT) or in vitro assays for latex-specific IgE are performed. While the SPT is regarded as a primary confirmatory test for IgE-mediated disease, the absence of a U.S. Food and Drug Administration-licensed HEVEA: brasiliensis latex extract has restricted its use in diagnosis. Serological tests have, therefore, become critically important as alternative diagnostic tests. Three manufacturers currently have FDA clearance for in vitro tests, to detect NRL-specific IgE. The commercially available assays may disagree on the antibody status of an individual serum, which may be due to the assay's detecting anti-NRL IgEs to different allergenic NRL proteins. Sensitized individuals produce specific IgE antibody to at least 10 potent HEVEA: allergens, Hev b 1-Hev b 10, each of which differs in its structure, size, and net charge. The relative content and ratios of Hevs in the

Monitoring of carbamazepine concentrations in wastewater and groundwater to quantify sewer leakage.

Science.gov (United States)

Fenz, R; Blaschke, A P; Clara, M; Kroiss, H; Mascher, D; Zessner, M

2005-01-01

Monitoring of carbamazepine concentrations in wastewater and groundwater enables us to identify and quantify sewer exfiltration. The antiepileptic drug carbamazepine is hardly removed in wastewater treatment plants and not or just slightly attenuated during bank infiltration and subsoil flow. Concentrations in wastewater are generally 1000 times higher than the limit of quantification. In contrast to . many other wastewater tracers carbamazepine is discharged to the environment only via domestic wastewater. The results from this study carried out in Linz, Austria indicate an average exfiltration rate of 1%, expressed as percentage of the dry weather flow that is lost to the groundwater on the city-wide scale. This rate is lower than sewage losses reported in most other studies which attempted to quantify exfiltration on the basis of groundwater pollution. However, it was also possible to identify one area with significantly higher sewage losses. This method seems to be very suitable for the verification of leakage models used to assess sewer exfiltration on a regional scale.

Antibacterial activity of the latex of Argemone ochroleuca Sweet

International Nuclear Information System (INIS)

Saad A. Alamri; Mahmoud F. Moustafa

2010-01-01

To investigate the antibacterial effect of the crude latex of Argemone ochroleuca (A. ochroleuca) as antibacterial potential against a range of human pathogenic bacteria. This study was carried out at King Khalid University, Abha, Kingdom of Saudi Arabia from January to March 2010. Seventeen ml of fresh latex from A. ochroleuca Sweet was collected, and the antibacterial activity of crude and diluted latex were examined using one ml of standardized inoculum suspension, and using the agar diffusion method test against Bacillus subtilis, Enterobacter aerogenes, Micrococcus luteus, Escherichia coli, and Staphylococcus aureus. All inoculated plates were incubated aerobically at 290C for 48 hours. The diameter of the zones of inhibition was measured to the nearest mm. The crude latex of A. ochroleuca exhibited a potent antibacterial effect on all bacterial strains examined. The zones of inhibition against the tested bacteria were found in the range of 9.30 - 40.3 mm along with their respective minimum inhibitory concentration values 100 ul/ml. The observable inhibition on selected bacteria by latex of A. ochroleuca makes it a promising alternative as a potential source of natural antibacterial (Author).

Evaluation of apparent viscosity of Para rubber latex by diffuse reflection near-infrared spectroscopy.

Science.gov (United States)

Sirisomboon, Panmanas; Chowbankrang, Rawiphan; Williams, Phil

2012-05-01

Near-infrared spectroscopy in diffuse reflection mode was used to evaluate the apparent viscosity of Para rubber field latex and concentrated latex over the wavelength range of 1100 to 2500 nm, using partial least square regression (PLSR). The model with ten principal components (PCs) developed using the raw spectra accurately predicted the apparent viscosity with correlation coefficient (r), standard error of prediction (SEP), and bias of 0.974, 8.6 cP, and -0.4 cP, respectively. The ratio of the SEP to the standard deviation (RPD) and the ratio of the SEP to the range (RER) for the prediction were 4.4 and 16.7, respectively. Therefore, the model can be used for measurement of the apparent viscosity of field latex and concentrated latex in quality assurance and process control in the factory.

Radiation vulcanization of natural rubber latex with low energy accelerator

Energy Technology Data Exchange (ETDEWEB)

Haque, Emdadul; Makuuchi, Keizo; Ikeda, Kenichi; Yoshii, Fumio; Kume Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Mitomo, Hiroshi [Gunma Univ., Faculty of Engineering, Department of Biological and Chemical Engineering, Kiryu, Gunma (Japan)

2001-03-01

The radiation vulcanization of natural rubber latex (RVNRL) with the recently installed electron beam (EB) pilot plant at Takasaki Radiation Chemistry Research Establishment, Takasaki, Japan has been discussed. The accelerating voltage and beam current of the plant are 250 kV and 10 mA respectively. The plant has a reaction vessel with the capacity of 18 liters latex to irradiate at a time. In order to obtain a suitable setting of experimental for RVNRL under EB of the plant the parameters such as irradiation time, defoamer concentration, volume of latex, beam current etc. are being optimized by varying the individual parameter at a constant set of the other variables. (author)

[Prevention of adverse effects in latex allergic patients: organizing a latex safe operating theatre].

Science.gov (United States)

Bonalumi, Sabrina; Barbonaglia, Patrizia; Bertocchi, Carmen

2006-01-01

In 2001 the General Health Direction of Region Lombardia approved (decree n. 22303) a guideline for the prevention of latex allergic reactions in patients and health care workers. This document provides general recommendations in order to standardize behaviors in regional health care facilities. The reason is due to a rise in the incident of reactions to latex products in the last 20 years. Nowadays the prevalence is higher in certain risk groups (subjected to frequent and repeated exposures) rather than the general population. The aim of the project was to organize a latex safe operating theatre in the Ospedale Maggiore Policlinico, Mangiagalli e Regina Elena of Milan (Fondazione) and to standardize behaviors in order to prevent adverse effects in latex allergic patients. Thanks to the literature review and the creation of a multidisciplinar team, we produced a protocol. Therefore, we requested manufacturers the certification of the latex content of their products. Results and conclusion. When latex allergic patients need to undergone surgery in our hospital, a latex safe operating theatre is organized by personnel following a multidisciplinar protocol. No allergic reactions were experienced during surgical procedures after the creation of an environment as free as possible from latex contamination. The project will involve an emergency room, one room or more of a ward and of the outpatients department.

Simulated Pathogen Concentrations in Locally-Collected Greywater and Wastewater

Data.gov (United States)

U.S. Environmental Protection Agency — This dataset contains simulated pathogen concentrations in locally-collected greywater and wastewater. Each .zip file includes 21 .csv files, each containing 10,000...

Radiation vulcanization of Philippine natural rubber latex

International Nuclear Information System (INIS)

Dela Rosa, Alumanda M.; Abad, Lucille V.; Sta, Lorna P.; Ana-Relleve; Tranquilan-Aranilla, Charito O.; Pascual, Cristina L.

1996-01-01

The response of Philippine natural rubber latex to radiation vulcanization and the stability of the irradiated natural rubber latex (INRL) upon storage and aging were investigated. Commercially available high ammonia (HA) concentrated lattices obtained from various rubber plantations in Mindanao Island were treated with 5 phr of n-butyl acrylate (nBA), and gamma-irradiated at the PNRI sup 60 Co irradiation facility at dose rate of 2.57 KGy/hr. Unirradiated cast latex films gave different green strength which varied from 2 - 11 MPa. Cast films from INRL exhibited maximum tensile strengths of 25 - 32 MPa at a radiation dose of 15 kGy. Higher tensile strengths were obtained from cast films with low Mg and high nitrogen contents. Thermal analysis using thermogravimetry (TG) revealed one major decomposition product at 374 degree C - 377 degree C. Its rate of decomposition decreased to a minimum at 15 kGy, then increased as radiation dose increased. This trend correlated well with the tensile strength measurements. The stability of the INRL upon storage and aging is an essential parameter to the rubber latex industry. For storage studies, INRL was stored for various periods of time. It was found that the pH and total solids content of the stored INRL did not change significantly after 12 months of storage; the MST values remained at above 100 seconds, and the viscosity decreased with time. The cast films exhibited a decline in tensile strength, modulus 300% and crosslinking density upon storage. While there were observed changes in the physical properties of the IRNL during the storage period, the data indicate that these properties were within values acceptable to the latex industry. Tests on the aging properties of INRL film were undertaken. It was shown that among the chemical antioxidants presently used by the latex industry. TNPP demonstrated the highest antioxidant property, followed by Antage DAHQ and Vulcanox BKF. Our data indicate that the natural rubber latex

Radiation vulcanization of Philippine natural rubber latex

International Nuclear Information System (INIS)

Dela Rosa, A.M.; Abad, L.V.; Sta.Ana-Relleve, L.P.; Tranquilan-Aranilla, C.O.; Pascual, C.L.

1996-01-01

The response of Philippine natural rubber latex to irradiation vulcanization and the stability of the irradiated natural rubber latex (INRL) upon storage and aging were investigated. Commercially available high ammonia (HA) concentrated latices obtained from various rubber plantations in Mindanao island were treated with 5 phr of n-butyl acrylate (nBA), and gamma-irradiated at the PNRI 60 Co irradiation facility at a dose rate of 2.57 kGy/hr. Unirradiated cast latex films gave different green strengths which varied from 2-11 MPa. Cast films from INRL exhibited maximum tensile strengths were obtained from cast films with low Mg and high nitrogen contents. Thermal analysis using thermogravimetry (TG) revealed one major decomposition product at 374 o -377 o C. Its rate of decomposition decreased to a minimum at 15 kGy, then increased as radiation dose was increased. This trend correlated well with the tensile strength measurements. The stability of the INRL upon storage and aging is an essential parameter to the rubbe latex industry. For storage studies, INRL was stored for various periods of time. It was found that the pH and total solids content of the stored INRL did not change significantly after 12 months of storage; the MST values remained at above 1000 seconds, and the viscosity decreased with time. The cast films exhibited a decline in tensile strength, modulus 300% , and crosslinking density upon storage. While there were observed changes in the physical properties of the INRL during the storage period, the data indicate that these properties were within values acceptable to the latex industry. Tests on the aging properties of INRL films were undertaken. It was shown that among the chemical antioxidants presently used by the latex industry, TNPP demonstrated the highest antioxidant property, followed by Antage DAHQ and Vulcanox BKF. Our data indicate that the natural rubber latex produced and processed in the Philippines is suited for radiation vulcanization

Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

International Nuclear Information System (INIS)

Dessouki, A.M.; Taher, N.H.; El-Nahas, H.H.

1996-01-01

The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the ζ potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs

Preparation of composites of national rubber latex (NRL) - portland cement mould. Vol. 3

Energy Technology Data Exchange (ETDEWEB)

Dessouki, A M; Taher, N H; El-Nahas, H H [National Center for Radiation Research and Technology, Atomic Energy Athority, Cairo (Egypt)

1996-03-01

The aim of this study is to prepare some polymeric mould using national rubber latex (NRL) - portland cement composites based on a delayed- action mechanism. Factors affecting the preparation process such as concentration, mixing percentage, additives and their effect on what is regarded as a delayed action coacervant combination was studied. Composites of national latex (NRL) - portland cement would were prepared as two separate parts. The stabilized natural rubber latex (NRL) 100 parts with hydroxy ethyl cellulose (HEC) 2 parts as stabilizer and a delayed - action coacervant (sodium meta silicate as a delaying agent) 5 parts on one hand and the dry blend of cement 65 parts soluble in 65 parts of water as a paste on the other hand were mixed thoroughly on site. (HEC) was added to the rubber latex to prevent the coagulation of the rubber latex with the electrolyte (sodium meta silicate) present in the rubber mixture. Two kinds of stabilization occurred in the rubber part, namely steric stabilization and the stabilization against electrolyte. The effect of delayed - action coacervant (sodium meta silicate) on the initial setting time of rubber - cement mould showed that the molding process did not occur at sodium meta silicate concentration less than 2.66 parts per 100 parts of rubber latex (phr), and the optimum concentration used was 5% parts of rubber latex. It was observed that addition of a delaying agent (Sodium meta silicate) to the rubber part enhanced the delaying mechanism in the time needed for the molding process, while the addition of the delaying agent to the cement part did not have any effect on retardation of the molding process. Chemical coacervants function mainly by reducing the {zeta} potential which is associated with the electrical double layer surrounding the latex particle. This reduction may brought about in at least three distinct ways which take place in the system studied. 5 figs., 3 tabs.

Transcript Profiling of Hevea brasiliensis during Latex Flow

Directory of Open Access Journals (Sweden)

Jinquan Chao

2017-11-01

Full Text Available Latex exploitation enhances latex regeneration in rubber trees. The latex exploitation-caused latex flow lasts from 10 min to a few hours, which is convenient for exploring the transcript profiling of latex metabolism-related genes at the different stages of latex flow. In the present study, the expression pattern of 62 latex metabolism-related genes involved in water transportation, carbohydrate metabolism, natural rubber biosynthesis, hormone signaling, ROS generation and scavenging, and latex coagulum across three stages of latex flow between rubber tree clones CATAS7-33-97 and CATAS8-79 were comparatively analyzed by quantitative real-time PCR. The two clones show differences in latex regeneration and have a different duration of latex flow. The results showed that the expression levels of 38 genes were significantly higher in CATAS8-79 latex than in CATAS7-33-97 during latex regeneration, while 45 genes had a notably higher expression level in CATAS8-79 latex during latex flow. Together with the activation of the MEP pathway and jasmonate pathway in CATAS8-79 latex, HbPIP1;3, HbPIP1;4, HbSUT3, HbSus3, HbHMGS1-2, HbMK should contribute to the high latex regeneration ability. The up-regulation of ethylene signaling and Hb44KD and the down-regulation of latex coagulation-related genes in CATAS8-79 latex might contribute to its longer latex flow duration. This study provides some cues for revealing the regulation of latex metabolism in rubber trees.

Latex allergy and filaggrin null mutations

DEFF Research Database (Denmark)

Carlsen, Berit C; Meldgaard, Michael; Hamann, Dathan

2011-01-01

to aeroallergens and it is possible that filaggrin null mutations also increase the risk of latex allergy. The aim of this paper was to examine the association between filaggrin null mutations and type I latex allergy. Methods Twenty latex allergic and 24 non-latex allergic dentists and dental assistants...... in the cases in this study may not have occurred through direct skin contact but through the respiratory organs via latex proteins that are absorbed in glove powder and aerosolized...

Treatment technology of low concentration uranium-bearing wastewater and its research progress

International Nuclear Information System (INIS)

Wei Guangzhi; Xu Lechang

2007-01-01

With growth of the discharged uranium-bearing wastewater capacity, a low cost and effective treatment technology is required to avoid transferring and diffusion of the radioactive nuclides. On the basis of analyses of the source and characteristics of the low-concentration uranium-bearing wastewater, the conventional treatment technologies, such as, flocculating settling, ion exchange, concentration, adsorption, and some innovatory technologies, such as, membrane, microorganism, phytoremediation and zero-valent iron technology are introduced. (authors)

Triterpenoid biosynthesis in Euphorbia lathyris latex

International Nuclear Information System (INIS)

Hawkins, D.R.

1987-11-01

The structures of triterpenols, not previously been known, from Euphorbia lathyris latex are reported. A method for quantifying very small amounts of these compounds was developed. Concerning the biochemistry of the latex, no exogenous cofactors were required for the biosynthesis and the addition of compounds such as NADPAH and ATP do not stimulate the biosynthesis. The addition of DTE or a similar anti-oxidant was found to help reduce the oxidation of the latex, thus increasing the length of time that the latex remains active. The requirement of a divalent cation and the preference for Mn in the pellet was observed. The effect of several inhibitors on the biosynthesis of the triterpenoids was examined. Mevinolin was found to inhibit the biosynthesis of the triterpenoids from acetate, but not mevalonate. A dixon plot of the inhibition of acetate incorporation showed an I 50 concentration of 3.2 μM. Fenpropimorph was found to have little or no effect on the biosynthesis. Tridemorph was found to inhibit the biosynthesis of all of the triterpenoids with an I 50 of 4 μM. It was also observed that the cyclopropyl containing triterpenols, cycloartenol and 24-methylenecycloartenol were inhibited much more strongly than those containing an 8-9 double bond, lanosterol and 24-methylenelanosterol. The evidence indicates, but does not definetely prove, that lanosterol and 24-methylenelanosterol are not made from cycloartenol and 24-methylenecycloartenol via a ring-opening enzyme such as cycloeucalenol-obtusifoliol isomerase. The possibilty that cycloartenol is made via lanosterol was investigated by synthesizing 4-R-4- 3 H-mevalonic acid and incubating latex with a mixture of this and 14 C-mevalonic acid. From the 3 H/ 14 C ratio it was shown that cycloartenol and 24-methylenecycloartenol are not made via an intermediate containing as 8-9 double bond. 88 refs., 15 figs., 30 tabs

Anti-ulcer activity of Synadenium grantii latex

Directory of Open Access Journals (Sweden)

Larissa L. G. Costa

2012-10-01

Full Text Available Synadenium grantii Hook f., Euphorbiaceae, is popularly known as leitosinha or janaúba. The diluted latex (18 drops/L of water is commonly used in the south of Brazil to treat gastric disturbances. This study evaluated phytochemical screening and toxicity using Artemia salina Leach of crude bark extract and also latex. The toxicity and the anti-ulcer activity of S. grantii latex were also tested in rats. Phytochemical results showed presence of tannins, terpenes, unsaponificable substances, coumarins and anthraquinones in the crude bark extract and terpenes in the latex. Gas chromatography-mass spectrometry (GC-MS analysis demonstrated the presence of diterpene tigliane esters in the latex, identified as 12-deoxyphorbol-13-(2-metilpropionate and phorbol 12,13,20-triacetate. The toxicity results using A. salina presented CL50 26.58μg/mL and CL50 778.66μg/mL, for the latex and the crude bark extract respectively. The toxicological hepatic parameters of the diluted latex were not different to the control group (p<0.05. The eosinophils cells showed an increase in both the diluted and pure latex groups. The pure latex showed gastric protection of 90% (p<0.05 and the diluted latex showed 6% compared to the negative control. Therefore, our data indicate that S. grantii latex, under research conditions presented gastric protection. Pure latex showed more toxicity than the diluted latex.

Impact of water management practice scenarios on wastewater flow and contaminant concentration.

Science.gov (United States)

Marleni, N; Gray, S; Sharma, A; Burn, S; Muttil, N

2015-03-15

Due to frequent droughts and rapid population growth in urban areas, the adoption of practices to reduce the usage of fresh water is on the rise. Reduction in usage of fresh water can be achieved through various local water management practices (WMP) such as Water Demand Management (WDM) and use of alternative water sources such as Greywater Recycling (GR) and Rainwater Harvesting (RH). While the positive effects of WMPs have been widely acknowledged, the implementation of WMPs is also likely to lower the wastewater flow and increase the concentration of contaminants in sewage. These in turn can lead to increases in sewer problems such as odour and corrosion. This paper analyses impacts of various WMP scenarios on wastewater flow and contaminant load. The Urban Volume and Quality (UVQ) model was used to simulate wastewater flow and the associated wastewater contaminants from different WMP scenarios. The wastewater parameters investigated were those which influence odour and corrosion problems in sewerage networks due to the formation of hydrogen sulphide. These parameters are: chemical oxygen demand (COD), nitrate (NO3(-)), sulphate (SO4(2-)), sulphide (S(2-)) and iron (Fe) that were contributed by the households (not including the biochemical process in sewer pipe). The results will help to quantify the impact of WMP scenarios on odour and corrosion in sewerage pipe networks. Results show that the implementation of a combination of WDM and GR had highly increased the concentration of all selected contaminant that triggered the formation of hydrogen sulphide, namely COD, sulphate and sulphide. On the other hand, the RH scenario had the least increase in the concentration of the contaminants, except iron concentrations. The increase in iron concentrations is actually beneficial because it inhibits the formation of hydrogen sulphide. Copyright © 2014 Elsevier Ltd. All rights reserved.

Latex Allergy In Health Care Workers

Directory of Open Access Journals (Sweden)

Hayriye Sarıcaoğlu

2013-05-01

Full Text Available Background and Design: We aimed to determine the frequency of latex allergy in our hospital and to to evaluate the clinical and demographical features of the cases.Materials and Methods: A detailed questionnaire was administered to healthcare workers by a physician. Skin prick test with latex and patch test with rubber chemicals and a piece of latex glove were performed for all healthcare workers. Latex-specific IgE was measured in serum.Results: The study sample consisted of 36 nurses, 14 doctors, and 50 healthcare workers. While 46 subjects had symptoms, 54 subjects had no symptoms. The relationship of clinical disease with working duration, exposure duration (hour/day, history of atopy, and drug/food allergies was statistically significant. Five nurses and 1 healthcare worker had positive skin prick test. Two of them had positive latex-specific IgE. Positive skin prick test statistically significantly correlated with occupation, working duration, exposure duration (hour/day and positive latex-specific IgE. Two nurses and 2 healthcare workers had positive latex-specific IgE. Two of them had positive skin prick test. Positive latexspecific IgE statistically significantly correlated with working duration, exposure duration, and positive skin prick test. Patch test with a piece of latex glove was negative in all subjects. Three healthcare workers had positive patch test with thiuram-mix, one of them had also positive patch test with mercaptobenzothiazole.Discussion: One of the risk factors for latex allergy is occupations involving frequent exposure to latex products. Latex allergy should be taken into consideration if type I hypersensitivity reactions occur in occupational groups at risk for anaphylactic reaction.

Experimental investigation of the effect of latex solid/water ratio on latex modified co-matrix mechanical properties

Directory of Open Access Journals (Sweden)

Ahmed M. Diab

2013-03-01

Full Text Available Numerous researches were performed on latex modified concretes and associated properties, however; some vital factors were not given attention in previous works. This study focus on new factor which significantly affects the properties of latex modified cement paste, mortar or concrete. This factor is termed as ‘latex solid/water ratio’ which is defined herein as the ratio of weight of solid latex to weight of total water content of cement composite including the water in latex itself. The effect of this factor on some properties of cement paste, mortar and concrete were experimentally evaluated. Properties of cement paste include the produced calcium hydroxide and ettringite content during hydration process, while those of cement mortar take account of absorption and effect of temperature on compressive strength. Furthermore, the effect of this factor on the compressive and flexural strengths, modulus of elasticity, water penetration depth and drying shrinkage of concrete were explored. Based on experimental evidences, and spite of using different cement contents, sources of latex, water–cement ratios and slump values, it can be generally concluded that the latex solid/water ratio is a dominant factor affecting different properties of latex modified mortars and concrete.

Advanced Oxidation Processes (AOPs for Refinery Wastewater Treatment Contains High Phenol Concentration

Directory of Open Access Journals (Sweden)

Azizah Alif Nurul

2018-01-01

Full Text Available Petroleum Refinery wastewater is characterized by a high phenol content. Phenol is toxic and resistant to biological processes for treatment of the petroleum refinery wastewater. The combination of an AOP and a biological process can be used for treatment of the refinery wastewater. It is necessary to conduct a study to determine the appropriate condition of AOP to meet the phenol removal level. Two AOP configurations were investigated: H2O2 / UV and H2O2 / UV / O3. From each process samples, COD, phenol and pH were measured. The oxidation was carried out until the targeted phenol concentration of treated effluent were obtained. The better result obtained by using process H2O2 / UV / O3 with the H2O2 concentration 1000 ppm. After 120 minutes, the final target has been achieved in which phenol concentration of 37.5 mg/L or phenol degradation of 93.75%.

Preparation of irradiated natural rubber latex-styrene copolymer for electrical gloves

International Nuclear Information System (INIS)

Made Sumarti Kardha

2010-01-01

Research on irradiated natural rubber latex-styrene copolymer to prepare electrical glove have been done. Vulcanization of natural rubber latex (NRL) was done by mixing 2 phr (per hundred of rubber) of normal butyl acrylate (n-BA) emulsion then irradiated with ã-ray "6"0Co at the dose of 30 kGy producing irradiated natural rubber latex (INRL). Natural rubber latex-styrene copolymers (SC) were prepared by mixing NRL and styrene monomer at styrene concentrations of 50 phr, 75 phr, 100 phr, 500 phr and irradiated at the doses of 15 kGy, 30 kGy and 45 kGy, then characterized their latex and film properties to obtain optimum SC of SC50. This optimum SC, SC50 then mixed with IRNL at the weight ratio of 0/100, 30/70, 50/50, 70/30 and 100/0, to produce irradiated natural rubber latex-styrene copolymer. The properties of copolymer rubber films made by dipping process i.e., % conversion, total solid content, latex viscosity, tensile strength, modulus 300 %, elongation at break, electrical resistance and dielectric constant were then characterized. Characterization result showed that (INRL-SC50) with 50/50 ratio irradiated at the dose of 30 kGy, have % conversion of 80.93 %, electrical resistivity of 1.73 x 10"1"4 Ohm cm and dielectric constant of 2.76 which fulfill the requirement as material for electrical gloves. (author)

Latex sensitisation in healthcare workers in Singapore.

Science.gov (United States)

Tang, M B Y; Leow, Y H; Ng, V; Koh, D; Goh, C L

2005-06-01

Epidemiological data on latex sensitisation among Asian healthcare workers is lacking. The aim of the study is to determine the rate of latex sensitisation in our healthcare workers. We recruited 313 healthcare workers, of which 46.6% were operating theatre staff and 53.4% were non-operating theatre staff. Seventy-one administrative staff served as controls. All participants answered a self-administered questionnaire relating to latex exposure and glove-related symptoms. Latex sensitisation was determined by skin prick testing to latex and latex-specific IgE detection. The prevalence of latex sensitisation among healthcare workers was 9.6%, with no difference between operating theatre and nonoperating theatre staff. Glove-related symptoms were reported in 13.7% of all healthcare workers, of which 22.9% were sensitised to latex. Only 26.7% of latex-sensitised healthcare workers had glove-related symptoms while the rest were asymptomatic. The most common symptoms were itch and hand eczema but the most important discriminating symptom was contact urticaria. Personal history of atopy was more common in sensitised healthcare workers (40.0%) compared to non-sensitised workers (31.8%). Only 1 out of 9 (11.2%) symptomatic latex-sensitised subjects had sought previous medical attention for the problem. Latex sensitisation among healthcare workers in Singapore should be considered a significant occupational health risk, as it is in the West. Increased screening and awareness of this problem is essential to identify those at risk.

Radiation vulcanization of natural rubber latex using irradiation n-butyl acrylate aqueous emulsion as sensitizer

International Nuclear Information System (INIS)

Vo Van Thien; Nguyen Quoc Hien; Keizo Makuuchi; Fumio Yoshii

2000-01-01

Natural rubber latex was vulcanized by gamma radiation with n-butyl acrylate aqueous emulsion irradiated at dose of 1.5 kGy as sensitizer. The total solid content of latex increases on the irradiation dose. The viscosity of latex on the standing time was investigated and became stable after one month of storage. The gel content of latex films increasing with irradiation dose and attained more than 94% at dose of 10 kGy. Tensile strength of films reached the values of 31MPa; 30 Mpa and 25 Mpa at vulcanization doses of 20 kGy, 15 kGy and 8 kGy for the concentrations of sensitizer 7 phr, 9 phr and 13 phr respectively. Elongation at break decreases as increasing dose. Tear strength of rubber films was from 30-40 N/mm. The tackiness of latex films decreases and smell of vulcanized latex is almost negligible. (author)

Triterpenoid biosynthesis in Euphorbia lathyris latex

Energy Technology Data Exchange (ETDEWEB)

Hawkins, D.R.

1987-11-01

The structures of triterpenols, not previously been known, from Euphorbia lathyris latex are reported. A method for quantifying very small amounts of these compounds was developed. Concerning the biochemistry of the latex, no exogenous cofactors were required for the biosynthesis and the addition of compounds such as NADPAH and ATP do not stimulate the biosynthesis. The addition of DTE or a similar anti-oxidant was found to help reduce the oxidation of the latex, thus increasing the length of time that the latex remains active. The requirement of a divalent cation and the preference for Mn in the pellet was observed. The effect of several inhibitors on the biosynthesis of the triterpenoids was examined. Mevinolin was found to inhibit the biosynthesis of the triterpenoids from acetate, but not mevalonate. A dixon plot of the inhibition of acetate incorporation showed an I/sub 50/ concentration of 3.2 ..mu..M. Fenpropimorph was found to have little or no effect on the biosynthesis. Tridemorph was found to inhibit the biosynthesis of all of the triterpenoids with an I/sub 50/ of 4 ..mu..M. It was also observed that the cyclopropyl containing triterpenols, cycloartenol and 24-methylenecycloartenol were inhibited much more strongly than those containing an 8-9 double bond, lanosterol and 24-methylenelanosterol. The evidence indicates, but does not definetely prove, that lanosterol and 24-methylenelanosterol are not made from cycloartenol and 24-methylenecycloartenol via a ring-opening enzyme such as cycloeucalenol-obtusifoliol isomerase. The possibilty that cycloartenol is made via lanosterol was investigated by synthesizing 4-R-4-/sup 3/H-mevalonic acid and incubating latex with a mixture of this and /sup 14/C-mevalonic acid. From the /sup 3/H//sup 14/C ratio it was shown that cycloartenol and 24-methylenecycloartenol are not made via an intermediate containing as 8-9 double bond. 88 refs., 15 figs., 30 tabs.

Aspects of Degradability and Aging of Natural Rubber Latex Films Obtained by Induced Ionizing Radiation Processes of Latex Vulcanization

International Nuclear Information System (INIS)

Parra, D. F.

2006-01-01

This study refers to the degradability of NRLF, natural rubber latex films, obtained by ionizing radiation. Three types of NRLF were prepared: irradiated latex, irradiated latex with about 1% of soy lecithin and sulfur-vulcanized latex, by cold vulcanization process. The films were buried in vases of two different kinds of soil: common soil and common soil with earthworm humus. Fast aging tests in laboratory with exposition to ultraviolet rays were done in irradiated latex films and irradiated latex films with soy lecithin. The results obtained after ten months of tests with buried films agree with the results of the fast aging tests, showing singularities of each type of soil and each kind of latex process. It also shows how weather inclemency can induce the films degradation process. The sulfur-vulcanized films were weakly degraded when buried. The films with lecithin and buried in vase with only common soil showed the biggest mass loss, but the films with lecithin buried in vases with common earthworm humus and soil increased their weigh and dimensions due to fungi formation. The irradiated latex films are more degradable then the sulfur-vulcanized films. The irradiated latex film, unlike the sulfur vulcanized film, showed high fungi colonization when buried. We conclude that the irradiated latex films are more easily biodegradable than the sulfur vulcanized latex films. The biodegradability increases with the addition of small amounts of soy lecithin (∼1%). The mechanical resistance of the buried films decreased related to the non-buried ones, proving that the outdoor aging in soil and the presence of fungi in the films can modify the mechanical properties of the irradiated latex owing to the biodegradation

Molluscicidal effect of Euphorbia umbellata (Pax Bruyns latex on Biomphalaria glabrata, Schistosoma mansoni host snail

Directory of Open Access Journals (Sweden)

Luciana Patrícia Lima Alves Pereira

2017-12-01

Full Text Available ABSTRACT Euphorbia umbellata (Pax Bruyns is an easily cultivated shrub, with occurrence in the tropical regions of the American and African continents. Chemical studies have revealed that the latex of this plant is rich in terpene compounds, which are highly toxic to snails Biomphalaria glabrata (Basommatophora: Planorbidae. The aim of this study was to evaluate the chemical composition and molluscicidal activity of the latex produced by E. umbellata, as well as the safety of its application in aquatic environments. The concentration of latex that killed 90% of the exposed snails after 24 h exposure (LC90 was 3.69 mg/L. Toxicity bioassays using Danio rerio (zebrafish revealed that these animals were less susceptible to latex than planorbids. However, it is important to perform other toxicity tests to ensure the feasibility of using latex to control populations of mollusks that contribute to schistosomiasis transmission. A phytochemical screening performed with the E. umbellata latex identified the triterpenoid and coumarin class. Further studies are warranted to isolate, identify, and test the active compounds of E. umbellata latex in B. glabrata.

Comparative study on plant latex particles and latex coagulation in Ficus benjamina, Campanula glomerata and three Euphorbia species.

Directory of Open Access Journals (Sweden)

Georg Bauer

Full Text Available Among latex-producing plants, mainly the latex of Hevea brasiliensis has been studied in detail so far, while comprehensive comparative studies of latex coagulation mechanisms among the more than 20,000 latex-bearing plant species are lacking. In order to give new insights into the potential variety of coagulation mechanisms, the untreated natural latices of five latex-bearing plants from the families Euphorbiaceae, Moraceae and Campanulaceae were visualised using Cryo-SEM and their particle size compared using the laser diffraction method. Additionally, the laticifers of these plants species were examined in planta via Cryo-SEM. Similar latex particle sizes and shape were found in Ficus benjamina and Hevea brasiliensis. Hence, and due to other similarities, we hypothesize comparable, mainly chemical, coagulation mechanisms in these two species, whereas a physical coagulation mechanism is proposed for the latex of Euphorbia spp. The latter mechanism is based on the huge amount of densely packed particles that after evaporation of water build a large surface area, which accelerates the coagulation procedure.

Osmotic de-swelling and swelling of latex dispersions

International Nuclear Information System (INIS)

Bonnet-Gonnet, Cecile

1993-01-01

This research thesis reports the comparison of, on the one hand, direct measurements of de-swelling resistance of latex dispersions obtained by osmotic pressure with, on the other hand, predictions made by models of electrostatic interactions. This resistance is explained in the case of sulphate-stabilised polystyrene particles (direct repulsion between charged particles), and in the case of copolymer (ps-pba) particles covered by an amphiphilic polymer (interactions between surface macromolecules and polymers). The study of de-swelling and swelling cycles highlights the existence of thresholds beyond which the concentrated dispersion has some cohesion. This irreversibility can be modelled by a Van der Waals attraction. The role of hydrophobic forces in latex destabilisation is studied [fr

Latex paint as a delivery vehicle for diethylphthalate and di-n-butylphthalate: predictable boundary layer concentrations and emission rates.

Science.gov (United States)

Schripp, Tobias; Salthammer, Tunga; Fauck, Christian; Bekö, Gabriel; Weschler, Charles J

2014-10-01

The description of emission processes of volatile and semi-volatile organic compounds (VOCs and SVOCs) from building products requires a detailed understanding of the material and the air flow conditions at the surface boundary. The mass flux between the surface of the material and air depends on the mass transfer coefficient (hm) through the boundary layer, the gas phase concentration of the target compound immediately adjacent to the material (y0), and the gas-phase concentration in bulk air (y(t)). In the present study emission experiments were performed in two chambers of quite different sizes (0.25 m(3) and 55 m(3)), and, in the larger chamber, at two different temperatures (23°C and 30°C). The emitting material was latex wall paint that had been doped with two plasticizers, diethylphthalate (DEP) and di-n-butylphthalate (DnBP). The phthalate content in the paint was varied in the small chamber experiment to evaluate the impact of the initial concentration in the bulk material (C0) on the emission rate. Boundary layer theory was applied to calculate hm for the specific phthalates from the Sherwood number (Sh) and the diffusion coefficient (Dair). Then y0 was determined based on the bulk gas-phase concentration at steady state (y¯). For both, DEP and DnBP, the y0 obtained was lower than the respective saturation vapor pressure (Ps). Furthermore, for both phthalates in latex paint, the material/air partition coefficient (C0/y0) was close in value to the octanol/air partition coefficient (KOA). This study provides a basis for designing phthalate emitting reference materials that mimic the emission behavior of common building materials. Copyright © 2014 Elsevier B.V. All rights reserved.

The physicochemical quality and meat microstructure of post laying hen with addition of Biduri (Calotropis gigantea) latex extract

Science.gov (United States)

Nuhriawangsa, A. M. P.; Hertanto, B. S.; Kartikasari, L. R.; Swastike, W.; Cahyadi, M.; Rasid, S.

2018-01-01

The objective of this study was to evaluate the effect of extract level of Biduri latex on the meat quality of laying hens. The materials of this research were Biduri latex and thigh meat from hens strain Lohman. The latex was tapped from a young tissue stem and centrifuged for its supernatant. Meats were smeared with latex, punctured and incubated for 30 minutes. Concentrations of latex were 0, 3, 6 and 9% from the weight of meat (w/w). The variables were water, dissolved protein, crude fat content, tenderness and microstructure of meat. The statistical analysis method using ANOVA and if there was a mean difference, Duncan test was used. Descriptive analysis was used for microstructures of meat by comparing its hydrolysis conditions. The study showed that fat had significant difference (P meat structure. The fat content increased with addition of 3% latex. The value of dissolved protein increased but tenderness decreased by addition extract of 6% latex. The addition of Biduri latex extract showed that hydrolysis in the microstructure of meat. The addition of 6% latex was the best meat quality.

Aggregation and charging of sulfate and amidine latex particles in the presence of oxyanions.

Science.gov (United States)

Sugimoto, Takuya; Cao, Tianchi; Szilagyi, Istvan; Borkovec, Michal; Trefalt, Gregor

2018-08-15

Electrophoretic mobility and time resolved light scattering are used to measure the effect on charging and aggregation of amidine and sulfate latex particles of different oxyanions namely, phosphate, arsenate, sulfate, and selenate. In the case of negatively charged sulfate latex particles oxyanions represent the coions, while they represent counterions in the case of the positively charged amidine latex. Repulsive interaction between the sulfate latex surface and the coions results in weak ion specific effects on the charging and aggregation. On the other hand the interaction of oxyanions with the amidine latex surface is highly specific. The monovalent dihydrogen phosphate ion strongly adsorbs to the positively charged surface and reverses the charge of the particle. This charge reversal leads also to the restabilization of the amidine latex suspension at the intermediate phosphate concentrations. In the case of dihydrogen arsenate the adsorption to amidine latex surface is weaker and no charge reversal and restabilization occurs. Similar differences are seen between the sulfate and selenate analogues, where selenate adsorbs more strongly to the surface as compared to the sulfate ion and invokes charge reversal. The present results indicate that ion specificity is much more pronounced in the case of counterions. Copyright © 2018 Elsevier Inc. All rights reserved.

Efficiency of 1,9- Nonane-diol-diacrylate as a radiation vulcanization accelerator for natural rubber latex

International Nuclear Information System (INIS)

Haque, M.E.

2003-09-01

The efficiency of 1,9- Nonane-diol-diacrylate (NDDA) as a radiation vulcanization accelerator (RVA) for natural rubber latex (NRL) was investigated. Both gamma rays and electron beam (EB) were used for vulcanizing NRL with NDDA. The radiation dose of gamma rays, concentration of NDDA required to vulcanize the latex were optimized. 20 kGy radiation dose of gamma rays and 5 phr concentration of NDDA were found optimum to get maximum tensile and related properties. NRL was vulcanized under EB to find out the optimum condition of irradiation with this RVA. The defoamer concentrations, length of irradiation time under EB, concentration of RVA were optimizer by changing various parameters of the EB machine with a constant set of the others. 0.2 phr defoamer concentration, 30 minutes irradiation time and 5 phr concentration of NDDA were found optimum for irradiation of NRL under the EB machine. Effect of low current and optimum volume of latex charged in the reaction vessel suitable for vulcanization at a time were found out. (author)

Preliminary Assessment of Growth Rates on Different Concentration of Microalgae Scenedesmus sp. in Industrial Meat Food Processing Wastewater

Directory of Open Access Journals (Sweden)

Latiffi Nur Atikah Ahmad

2017-01-01

Full Text Available This study is aimed to evaluate and access the growth rates and biomass productivity in different concentrations of microalgae Scenedesmus sp. using Industrial Meat Food Processing Wastewater as a media. The focus of this study is to determine the best concentrations of microalgae Scenedesmus sp. in raw wastewater in terms of kinetics of cells growth rates. The study verified that concentration of 1×106 cells/ml of microalgae gives the highest specific growth rates of biomass at 0.4488 day-1 and 1720 cells/ml/day compare to the other concentrations, while the lowest occurred at concentration of 1×103 cells/ml at 0.4108 day-1 and 14.9 cells/ml/day. The result shows the different concentration of microalgae Scenedesmus sp. culturing in Industrial Food Processing Wastewater influence the cells growth of biomass and the optimum were obtained at concentration of 1×106 cells/ml which suggested use for Industrial Meat Food Processing Wastewater Treatment purposed. With this finding, it should be seemly to adopt and applied efficiently in treating the wastewater especially for Scenedesmus sp. type of microalgae.

Formation of titanate nanostructures under different NaOH concentration and their application in wastewater treatment

International Nuclear Information System (INIS)

Huang Jiquan; Cao Yongge; Deng Zhonghua; Tong Hao

2011-01-01

The effects of the concentration of NaOH on the formation and transformation of various titanate nanostructures were studied. With increasing NaOH concentration, three different formation mechanisms were proposed. Nanotubes can only be obtained under moderate NaOH conditions, and should transform into nanowires with prolonged hydrothermal treatment, and their formation rate is accelerated by increasing NaOH concentration. Low concentration of NaOH results in the direct formation of nanowires, while extra high concentration of NaOH leads to the formation of amorphous nanoparticles. Adsorption and photocatalysis studies show that titanate nanowires and nanotubes might be potential adsorbents for the removal of both heavy metal ions and dyes and photocatalysts for the removal of dyes from wastewater. -- Graphical abstract: The morphologies of the titanates depend deeply on the concentration of NaOH. With increasing NaOH concentration, three different formation mechanisms were proposed. The application of these titanate nanostructures in the wastewater treatment was studied. Display Omitted Research highlights: → Effect of NaOH concentration on the structures of various titanates was reported. → Three different formation mechanisms were presented with increasing NaOH concentration. → Various titanates were used as adsorbents/photocatalysts in wastewater treatment.

[Latex allergy in a population at risk].

Science.gov (United States)

Ruiz Fernández, M; Flores Sandoval, G; Orea Solano, M

1999-01-01

The allergy to latex is an illness whose prevalence has been increased in very significant form in the last years. To know the allergy incidence to latex in population of risk, as well as to identify the related sintomatology and the importance or paper that play the atopia antecedents and time of contact with latex for the development of the illness. We carry out a prospective, descriptive, experimental and traverse study in population of risk, in the service of Allergy and clinical Immunology of the Hospital Regional Lic. Adolfo López Mateos, ISSSTE. One hundred patients of both sexes were included, with age of 20 to 50 years, with the antecedent of being personal medical and paramedic and to have presented contact with latex material in a minimum period of one year. They were carried out clinical history with registration of sintomatology nasal, bronchial, cutaneous and associated to contact with latex. They were carried out cutaneous test for prick to latex with positive control with the help of histamine solution and negative control with solution of Evans and immediate reading of the same one. 22% of the patients in study, they presented positive skin test latex, with a time of exhibition 10 year-old average, 68% presented antecedent of atopy personal, family and, likewise the associate sintomatology was in a 33.3% dermatology, 54.5 nasal, nobody presented bronchial symptoms and a 9% asymptomatic was reported. We support that the immediate skin test latex for Prick is an important parameter of support diagnosis for allergy to type 1 latex.

Nitrile versus Latex for Glove Juice Sampling.

Science.gov (United States)

Landers, Timothy F; Dent, Anthony

2014-01-01

The objective of this study was to explore the utility of nitrile gloves as a replacement for latex surgical gloves in recovering bacteria from the hands. Two types of nitrile gloves were compared to latex gloves using the parallel streak method. Streaks of Klebsiella pneumoniae and Staphylococcus aureus were made on tryptic soy agar plates, and the zones of inhibition were measured around pieces of glove material placed on the plates. Latex gloves produced a mean zone of inhibition of 0.28 mm, compared to 0.002 mm for nitrile gloves (pnitrile may be a viable alternative to latex in glove juice sampling methods, since nitrile avoids the risk of latex exposure.

Isolation rubber latex binary composites consisting of cotton and poly-N, N-dimethyl-N, N-diallilammony chloride

Directory of Open Access Journals (Sweden)

J. Cornejo Tueros

2012-01-01

Full Text Available The paper discusses the application of rubber from latex binary coagulating agent consisting of cotton - textile waste and polymeric quaternary ammonium salts. The influence on the process of extracting rubber from latex flow coagulating agent temsperatury and concentration of the dispersed phase.

Latex improvement of recycled asphalt pavement

Science.gov (United States)

Drennon, C.

1982-08-01

The performance of a single unmodified milled recycled asphalt concrete was compared to milled asphalt concrete modified by addition of three types of rubber latex. Latex was added at 2, 3, 5, and 8 percent latex by weight of asphalt in the asphalt concrete. Lattices used were a styrene butadiene (SBR), a natural rubber (NR), an acrylonitrile butadiene (NBR), and four varieties of out of specification SBR lattices. Marshall tests, while indecisive, showed a modest improvement in properties of SBR and NR added material at 3 and 5 percent latex. Addition of NBR latex caused deterioration in Marshall stability and flow over that of control. Repeated load tests were run using the indirect tensile test, analyzed by the VESYS program, which computes life of pavements. Repeated load tests showed improvement in asphalt concrete life when 3 and 5 percent SBR was added. Improvement was also shown by the out of specification SBR.

Detection of latex allergens by immunoelectron microscopy in ambient air (PM10) in Oslo, Norway (1997-2003).

Science.gov (United States)

Namork, Ellen; Kurup, Viswanath P; Aasvang, Gunn Marit; Johansen, Bjørn V

2004-11-01

The authors collected ambient air along two highways in Oslo to investigate the annual variations in particulate matter (PM10) and the presence of latex as an outdoor allergen. PMI, was monitored for a period of five years, during which time the use of studded winter tires was reduced. The presence of latex and of common aeroallergens was examined directly on the collection filters with immunoelectron microscopy visualized in a scanning electron microscope. The annual variation in PM10 was similar over the five years of sampling, with increased mass concentrations in winter. Statistical analysis indicated no major effect from the change to nonstudded tires. The most important factors influencing the PM10 concentration were meteorological parameters like wind and rain. Immnunolabeling of the filters showed latex as an outdoor allergen that adhered to carbon aggregates from vehicle emission. The results also indicated cross-reactive epitopes among the common allergens investigated, which for sensitized subjects may add to the risk of developing latex allergy.

Radiation-induced grafting polymerization of MMA onto polybutadiene rubber latex

International Nuclear Information System (INIS)

Peng Jing; Wang Maolin; Qiao Jinliang; Wei Genshuan

2005-01-01

The grafting of methyl methacrylate (MMA) onto polybutadiene rubber latex by the direct radiation method was carried out. The effects of monomer concentration, absorbed dose and dose rate of gamma rays on the grafting yield were investigated. The graft copolymers were characterized by transmission electron microscopy (TEM), FTIR spectroscopy, and differential scanning calorimetry. TEM photographs revealed that the core-shell structures of latex particles are formed at low MMA content, and with the increasing of MMA content, the semi-IPN-like structure with core-shell could be developed due to the high gel fraction of polybutadiene (PBD) seed particles. In addition, infrared analysis confirmed that MMA could be grafted onto PBD molecular chains effectively under appropriate irradiation conditions. The interfacial adhesion between PBD rubber (core) and PMMA (shell) phases could be enhanced with the increase of MMA concentration

Wastewater treatment and pollution control in Indonesia

International Nuclear Information System (INIS)

Danu, Sugiarto

2006-01-01

Present status of radiation facilities for Co-60 gamma ray irradiation and electron beam irradiation in Indonesia is first presented. Wastewater treatment is explained: kinds of waste, industrial, agricultural, municipal and nuclear. Each liquid wastewater containing various kinds of contaminants, radioactive or non-radioactive is differently treated by waste treatment industries. On-going project is use of electron beams in which combination with ozone to reduce chlorinated solvent, disinfected sludge from sewage treatment containing organic and inorganic components for soil fertilizer, and high color river water for water supplying. The cost factor and the effect of combined treatment are being examined. Other on-going projects are applications of electron beams for vulcanization of natural rubber latex and flue gas treatment by BATAN. (S. Ohno)

Exploiting epoxidized natural rubber latex (ENRL) as a starting raw material for latex-based products

Science.gov (United States)

Siti Nor Qamarina, M.; Fatimah Rubaizah, M. R.; Nurul Suhaira, A.; Norhanifah, M. Y.

2017-12-01

Epoxidized natural rubber latex (ENRL) is a chemically modified natural rubber latex produced from epoxidation process that involves usage of organic peracids. Conversion of the ENRL into dry rubber products has been known to exhibit many beneficial properties, however limited published works were found on diversifiying the ENRL latex-based products applications. In this preliminary work, different source of raw materials and neutralization systems were investigated. The objective was to explore possibilities in producing distinctive ENRL. Findings have demonstrated that different source of raw materials and neutralization systems influenced the typical ENRL specifications, stability behavior and particle size distribution. Morphological observations performed on these ENRL systems appeared to agree with the ENRL characteristics achieved. Since experimenting these two main factors resulted in encouraging ENRL findings, detailed work shall be further scrutinized to search for an optimum condition in producing marketable ENRL specifically for latex-based products applications.

Emotion with tears decreases allergic responses to latex in atopic eczema patients with latex allergy.

Science.gov (United States)

Kimata, Hajime

2006-07-01

Allergic responses are enhanced by stress, whereas they are reduced by laughter in atopic eczema patients. Emotion with tears decreases plasma IL-6 levels in patients with rheumatoid arthritis. Thus, the effect of emotion with tears on allergic responses in patients with atopic eczema was studied. Sixty patients with atopic eczema having latex allergy viewed both the weather information video and the heart-warming movie, Kramer vs. Kramer. Just before and immediately after viewing each video, allergic responses to latex were measured. Viewing the weather information video did not cause emotion with tears in any patients, and it failed to modulate allergic responses. In contrast, viewing Kramer vs. Kramer caused emotion with tears in 44 of 60 patients, and it reduced allergic skin wheal responses to latex and latex-specific IgE production in them. Emotion with tears reduced allergic responses, and it may be useful in the treatment of allergic diseases.

Maillard Reaction in Natural Rubber Latex: Characterization and Physical Properties of Solid Natural Rubber

Directory of Open Access Journals (Sweden)

S. Montha

2016-01-01

Full Text Available Maillard reaction in Natural Rubber (NR latex was investigated by treating fresh NR latex with glutaraldehyde (C5H8O2 in amounts of 0, 50, 100, and 200 mmol/kg of latex. Protein cross-linking in fresh NR latex and solid NR was confirmed by using sodium dodecylsulfate polyacrylamide gel electrophoresis (SDS-PAGE and attenuated total reflection infrared (ATR-IR spectroscopy, respectively. It was found that degree of protein cross-linking in NR increased with increasing C5H8O2 concentration. Physical properties of untreated and treated NR substances in terms of gel content, initial Wallace plasticity (P0, plasticity retention index (PRI, Mooney viscosity, and tensile strength were carefully explored. Results clearly showed that the Maillard cross-linking of proteins had remarkable effect on bulk NR properties, that is, solvent resistance, hardness, resistance to oxidation, rheological behavior, and resistance to stretching out.

Experimental study on the drying of natural latex medical gloves

Science.gov (United States)

Chankrachang, Mano; Yongyingsakthavorn, Pisit; Tohsan, Atitaya; Nontakaew, Udomkiat

2018-01-01

The purpose of this research was to study latex film drying at 70 °C using a laboratory drying oven. Two different total solid content (TSC) latex compounds, which 45% TSC and 35% TSC were used. The undried latex films were prepared according to the common procedures used in latex gloves manufacturers, that is, by dry coagulant dipping process. The experimental results such as initial moisture content, the amount of moisture and drying time of latex films in each latex compound formula were determined. After that, the results were projected to calculate on the production capacity expand by 1 million piece/day of natural latex medical gloves. Finally, the rate of moisture entering the latex drying oven and the energy consumption of the drying oven were estimated. The results indicated that when the 35% TSC of latex compound was used. The initial moisture content of latex film was higher than 45% TSC of latex compound about 7%. The drying time of 35% TSC was longer than 45% TSC for 2.5 min and consume more energy about 10%. As a result, the 45% TSC latex compound was the better way to saving energy and managing humidity in the production line. Therefore, it was found to very useful to an approximate design length and size of actual of latex drying oven and the rate of moisture entering the oven as well.

A pilot-scale forward osmosis membrane system for concentrating low-strength municipal wastewater: performance and implications

Science.gov (United States)

Wang, Zhiwei; Zheng, Junjian; Tang, Jixu; Wang, Xinhua; Wu, Zhichao

2016-02-01

Recovery of nutrients and energy from municipal wastewater has attracted much attention in recent years; however, its efficiency is significantly limited by the low-strength properties of municipal wastewater. Herein, we report a pilot-scale forward osmosis (FO) system using a spiral-wound membrane module to concentrate real municipal wastewater. Under active layer facing feed solution mode, the critical concentration factor (CCF) of this FO system was determined to be 8 with 0.5 M NaCl as draw solution. During long-term operation at a concentration factor of 5, (99.8 ± 0.6)% of chemical oxygen demand and (99.7 ± 0.5)% of total phosphorus rejection rates could be achieved at a flux of 6 L/(m2 h) on average. In comparison, only (48.1 ± 10.5)% and (67.8 ± 7.3)% rejection of ammonium and total nitrogen were observed. Cake enhanced concentration polarization is a major contributor to the decrease of water fluxes. The fouling also led to the occurrence of a cake reduced concentration polarization effect, improving ammonium rejection rate with the increase of operation time in each cycle. This work demonstrates the applicability of using FO process for wastewater concentrating and also limitations in ammonium recovery that need further improvement in future.

Nitrile versus Latex for Glove Juice Sampling.

Directory of Open Access Journals (Sweden)

Timothy F Landers

Full Text Available The objective of this study was to explore the utility of nitrile gloves as a replacement for latex surgical gloves in recovering bacteria from the hands. Two types of nitrile gloves were compared to latex gloves using the parallel streak method. Streaks of Klebsiella pneumoniae and Staphylococcus aureus were made on tryptic soy agar plates, and the zones of inhibition were measured around pieces of glove material placed on the plates. Latex gloves produced a mean zone of inhibition of 0.28 mm, compared to 0.002 mm for nitrile gloves (p<.001. While the parallel streak method is not intended as a quantitative estimate of antimicrobial properties, these results suggest that nitrile may be a viable alternative to latex in glove juice sampling methods, since nitrile avoids the risk of latex exposure.

Latex and friends

CERN Document Server

Dongen, M R C van

2012-01-01

LaTeX is a free, automated state-of-the-art typesetting system. This book teaches all the ins and outs of LaTeX which are needed to write an article, report, thesis, or book. The book teaches by example, giving many worked out examples showing input and output side by side. The book presents the most recent techniques for presenting data plots, complex graphics, and computer presentations, but does not require previous knowledge. However, it is also a reference for the more seasoned user, with pointers to modern techniques and packages. Recurring themes in the book are consistent and effective

Identification, quantification, spatiotemporal distribution and genetic variation of major latex secondary metabolites in the common dandelion (Taraxacum officinale agg.).

Science.gov (United States)

Huber, Meret; Triebwasser-Freese, Daniella; Reichelt, Michael; Heiling, Sven; Paetz, Christian; Chandran, Jima N; Bartram, Stefan; Schneider, Bernd; Gershenzon, Jonathan; Erb, Matthias

2015-07-01

The secondary metabolites in the roots, leaves and flowers of the common dandelion (Taraxacum officinale agg.) have been studied in detail. However, little is known about the specific constituents of the plant's highly specialized laticifer cells. Using a combination of liquid and gas chromatography, mass spectrometry and nuclear magnetic resonance spectrometry, we identified and quantified the major secondary metabolites in the latex of different organs across different growth stages in three genotypes, and tested the activity of the metabolites against the generalist root herbivore Diabrotica balteata. We found that common dandelion latex is dominated by three classes of secondary metabolites: phenolic inositol esters (PIEs), triterpene acetates (TritAc) and the sesquiterpene lactone taraxinic acid β-D-glucopyranosyl ester (TA-G). Purification and absolute quantification revealed concentrations in the upper mgg(-1) range for all compound classes with up to 6% PIEs, 5% TritAc and 7% TA-G per gram latex fresh weight. Contrary to typical secondary metabolite patterns, concentrations of all three classes increased with plant age. The highest concentrations were measured in the main root. PIE profiles differed both quantitatively and qualitatively between plant genotypes, whereas TritAc and TA-G differed only quantitatively. Metabolite concentrations were positively correlated within and between the different compound classes, indicating tight biosynthetic co-regulation. Latex metabolite extracts strongly repelled D. balteata larvae, suggesting that the latex constituents are biologically active. Copyright © 2015 Elsevier Ltd. All rights reserved.

Preliminary Study on the Effect of Wastewater Storage in Septic Tank on E. coli Concentration in Summer

Directory of Open Access Journals (Sweden)

James K. Bradshaw

2013-07-01

Full Text Available On-site wastewater treatment systems (OWTS work by first storing the wastewater in a septic tank before releasing it to soils for treatment that is generally effective and sustainable. However, it is not clear how the abundance of E. coli changes during its passage through the tank. In this study, which was conducted under the UGA young Scholar Program in summer of 2010, we examined the change in wastewater quality parameters during the passage of the wastewater through the tank and after its release into soil. We collected wastewater samples at the inlet and outlet of an experimental septic tank in addition to obtaining water samples from lysimeters below trenches where the drainpipes were buried. We report that E. coli concentration was higher by 100-fold in the septic tank effluent than influent wastewater samples, indicating the growth of E. coli inside the tank under typical Georgian summer weather. This is contrary to the assumption that E. coli cells do not grow outside their host and suggests that the microbial load of the wastewater is potentially enhanced during its storage in the tank. Electrical conductivity, pH and nitrogen were similar between the influent and effluent wastewater samples. E. coli and total coliform concentrations were mainly below detection in lysimeter samples, indicating the effectiveness of the soil in treating the wastewater.

Cement-latex grouting mortar for cementing boreholes

Energy Technology Data Exchange (ETDEWEB)

Kateev, I S; Golyshkina, L A; Gorbunova, I V; Kurochkin, B M; Vakula, Ya V

1980-01-01

The need for the development of cement-latex grouting mortar for the purpose of separating strata when reinforcing boreholes at deposits in the Tatar Associated SSR is evaluated. Results of studies of the physical and mechanical properties of cement-latex grouting mortar systems (mortar plus brick) are presented. Formulas for preparing cement-latex grouting mortor are evaluated and results of industrial tests of such mortars shown.

Concentrations, Stability, and Isolation of the Furan Fatty Acid 9-(3-Methyl-5-pentylfuran-2-yl)-nonanoic Acid from Disposable Latex Gloves.

Science.gov (United States)

Müller, Marco; Hogg, Melanie; Ulms, Kerstin; Vetter, Walter

2017-09-13

Because of their antioxidant properties, furan fatty acids (furan-FAs) are valuable minor compounds with a widespread occurrence in all living matter. Unfortunately, pure standards are not readily available, because they usually contribute only 1% to the lipid fraction. A known exception of this is the milky fluid of Hevea brasiliensis, commonly known as latex, in which the furan-FA 9-(3-methyl-5-pentylfuran-2-yl)-nonanoic acid (9M5) contributes about 90% to the triacylglycerides. In this study, we investigated the content of 9M5 in 30 different disposable latex gloves, which ranged from 0.7 to 8.2 mg/g of glove. The light degradability of 9M5 in latex gloves was investigated, and different amounts of 9M5 in disposable latex gloves were attributed to varying exposure time to light. Additionally, over 100 mg of the methyl or ethyl ester of 9M5 (purity of >98%) could be extracted from disposable latex gloves, employing cold extraction and silver ion chromatography. With this method, standards for the quantitation of furan-FAs are obtained easily and rapidly in all laboratories.

Jackfruit anaphylaxis in a latex allergic patient.

Science.gov (United States)

Wongrakpanich, Supakanya; Klaewsongkram, Jettanong; Chantaphakul, Hiroshi; Ruxrungtham, Kiat

2015-03-01

Several fruits have been reported to crossreact with latex antigen in latex allergy patients but little is known regarding tropical fruits in particular. Here we report the case of a 34-year old nurse who developed anaphylaxis following the ingestion of dried jackfruit (Artocarpus heterophyllus). The patient had a history of chronic eczema on both hands resulting from a regular wear of latex gloves. She and her family also had a history of atopy (allergic rhinitis and/or atopic dermatitis). The results of skin prick tests were positive for jackfruit, latex glove, kiwi and papaya, but the test was negative for banana. While we are reporting the first case of jackfruit anaphylaxis, further research needs to be conducted to identify the mechanisms underlying it. In particular, in-vitro studies need to be designed to understand if the anaphylaxis we describe is due to a cross reactivity between latex and jackfruit or a coincidence of allergy to these 2 antigens.

A novel arctigenin-containing latex glove prevents latex allergy by inhibiting type I/IV allergic reactions.

Science.gov (United States)

Wang, Yong-Xin; Xue, Dan-Ting; Liu, Meng; Zhou, Zheng-Min; Shang, Jing

2016-03-01

The present study aimed at developing a natural compound with anti-allergic effect and stability under latex glove manufacturing conditions and investigating whether its anti-allergic effect is maintained after its addition into the latex. The effects of nine natural compounds on growth of the RBL-2H3 cells and mouse primary spleen lymphocytes were determined using MTT assay. The compounds included glycyrrhizin, osthole, tetrandrine, tea polyphenol, catechin, arctigenin, oleanolic acid, baicalin and oxymatrine. An ELISA assay was used for the in vitro anti-type I/IV allergy screening; in this process β-hexosaminidase, histamine, and IL-4 released from RBL-2H3 cell lines and IFN-γ and IL-2 released from mouse primary spleen lymphocytes were taken as screening indices. The physical stability of eight natural compounds and the dissolubility of arctigenin, selected based on the in vitro pharnacodynamaic screening and the stability evaluation, were detected by HPLC. The in vivo pharmacodynamic confirmation of arctigenin and final latex product was evaluated with a passive cutaneous anaphylaxis (PCA) model and an allergen-specific skin response model. Nine natural compounds showed minor growth inhibition on RBL-2H3 cells and mouse primary spleen lymphocytes. Baicalin and arctigenin had the best anti-type I and IV allergic effects among the natural compounds based on the in vitro pharmacodynamic screening. Arctigenin and catechin had the best physical stability under different manufacturing conditions. Arctigenin was the selected for further evaluation and proven to have anti-type I and IV allergic effects in vivo in a dose-dependent manner. The final product of the arctigenin-containing latex glove had anti-type I and IV allergic effects in vivo which were mainly attributed to arctigenin as proved from the dissolubility results. Arctigenin showed anti-type I and IV allergic effects in vitro and in vivo, with a good stability under latex glove manufacturing conditions

THE USE OF HALLOYSITE TO REDUCE POLLUTIONS CONCENTRATION IN MUNICIPAL WASTEWATER

Directory of Open Access Journals (Sweden)

Alicja Machnicka

2016-12-01

Full Text Available One of the methods of municipal wastewater treatment allows the use of biofilters. The study used a bed filled halloysite. In operation of the bed, depending on the hydraulic load, the concentration of phosphate, ammonium and organic matter was reduced. Highest reduction of the concentration PO43- (89% and N – NH4+ (81% in the waste water of the hydraulic load – 0,04 m3/m2h was obtained. The concentration of the organic substrate was reduced by approximately 86%.

Allergy to latex in health workers

Directory of Open Access Journals (Sweden)

Fajardo-Zapata, Álvaro L.

2015-01-01

Full Text Available Introduction: A common and growing problem in hospitals is hypersensitivity to rubber latex antigens, since many products, including gloves, are manufactured from this material, with the consequent possibility of producing allergy in persons who use them. Objective: To find out if health workers at a fourth level clinic in Bogotá, Colombia, are allergic to rubber latex, in relation to the use of gloves. Materials and methods: Descriptive, cross-sectional study of a non-probabilistic intentional-type sample in each one of four hospital units. A survey was applied to participants. Results: 16 of the 26 persons (61.5% with history of allergic processes manifested some kind of reaction when they had contact with latex gloves; the problem was more significant in the nursing personnel compared to physicians. Conclusions: The exposure to latex gloves may be generating the appearance of allergic occupational disease in health workers.

The preparation of RVNRL using Malaysian-produced latexes

International Nuclear Information System (INIS)

Zin, W.M. bin W.; Mohid, N. bte; Hasan, J. bin; Noor, W.K.A. bte W.M.; Jaafar, Zulkifli

1993-01-01

This research project was carried out using latexes supplied by three of the suppliers in Malaysia. From the results of studies carried out in search of the best sensitiser for RVNRL preparation, the use of n-butyl acrylate (n-BA) as a sensitiser gave the most promising results. However, its use as a sensitiser is not universal to all latexes available in the country. The problem was overcome by using different formulations for different latexes. For the latex supplied by Golden Hope (Hytex), a combination of sensitisers i.e. n-BA plus 2-ethyl hexyl acrylate (2-EHA) with a 10% potassium hydroxide solution as the stabilizer, was required. Latex supplied by MARDEC (Matex), seemed to need only n-BA as the sensitiser. However, a stabilizer was still required and the use of a 10% KOH solution was found to be suitable. A large range of stabilizers and sensitisers were applicable to Guthrie latex. The use of n-BA as the sensitiser and potassium laurylic acid as the stabilizer seemed the most favourable formulation. All the results are discussed in the form of a correlation between dose and the tensile properties of RVNRL vulcanizates, equilibrium swelling ratio and standing time of the latex formulation. (author)

A Latex Metabolite Benefits Plant Fitness under Root Herbivore Attack.

Directory of Open Access Journals (Sweden)

Meret Huber

2016-01-01

Full Text Available Plants produce large amounts of secondary metabolites in their shoots and roots and store them in specialized secretory structures. Although secondary metabolites and their secretory structures are commonly assumed to have a defensive function, evidence that they benefit plant fitness under herbivore attack is scarce, especially below ground. Here, we tested whether latex secondary metabolites produced by the common dandelion (Taraxacum officinale agg. decrease the performance of its major native insect root herbivore, the larvae of the common cockchafer (Melolontha melolontha, and benefit plant vegetative and reproductive fitness under M. melolontha attack. Across 17 T. officinale genotypes screened by gas and liquid chromatography, latex concentrations of the sesquiterpene lactone taraxinic acid β-D-glucopyranosyl ester (TA-G were negatively associated with M. melolontha larval growth. Adding purified TA-G to artificial diet at ecologically relevant concentrations reduced larval feeding. Silencing the germacrene A synthase ToGAS1, an enzyme that was identified to catalyze the first committed step of TA-G biosynthesis, resulted in a 90% reduction of TA-G levels and a pronounced increase in M. melolontha feeding. Transgenic, TA-G-deficient lines were preferred by M. melolontha and suffered three times more root biomass reduction than control lines. In a common garden experiment involving over 2,000 T. officinale individuals belonging to 17 different genotypes, high TA-G concentrations were associated with the maintenance of high vegetative and reproductive fitness under M. melolontha attack. Taken together, our study demonstrates that a latex secondary metabolite benefits plants under herbivore attack, a result that provides a mechanistic framework for root herbivore driven natural selection and evolution of plant defenses below ground.

A Latex Metabolite Benefits Plant Fitness under Root Herbivore Attack.

Science.gov (United States)

Huber, Meret; Epping, Janina; Schulze Gronover, Christian; Fricke, Julia; Aziz, Zohra; Brillatz, Théo; Swyers, Michael; Köllner, Tobias G; Vogel, Heiko; Hammerbacher, Almuth; Triebwasser-Freese, Daniella; Robert, Christelle A M; Verhoeven, Koen; Preite, Veronica; Gershenzon, Jonathan; Erb, Matthias

2016-01-01

Plants produce large amounts of secondary metabolites in their shoots and roots and store them in specialized secretory structures. Although secondary metabolites and their secretory structures are commonly assumed to have a defensive function, evidence that they benefit plant fitness under herbivore attack is scarce, especially below ground. Here, we tested whether latex secondary metabolites produced by the common dandelion (Taraxacum officinale agg.) decrease the performance of its major native insect root herbivore, the larvae of the common cockchafer (Melolontha melolontha), and benefit plant vegetative and reproductive fitness under M. melolontha attack. Across 17 T. officinale genotypes screened by gas and liquid chromatography, latex concentrations of the sesquiterpene lactone taraxinic acid β-D-glucopyranosyl ester (TA-G) were negatively associated with M. melolontha larval growth. Adding purified TA-G to artificial diet at ecologically relevant concentrations reduced larval feeding. Silencing the germacrene A synthase ToGAS1, an enzyme that was identified to catalyze the first committed step of TA-G biosynthesis, resulted in a 90% reduction of TA-G levels and a pronounced increase in M. melolontha feeding. Transgenic, TA-G-deficient lines were preferred by M. melolontha and suffered three times more root biomass reduction than control lines. In a common garden experiment involving over 2,000 T. officinale individuals belonging to 17 different genotypes, high TA-G concentrations were associated with the maintenance of high vegetative and reproductive fitness under M. melolontha attack. Taken together, our study demonstrates that a latex secondary metabolite benefits plants under herbivore attack, a result that provides a mechanistic framework for root herbivore driven natural selection and evolution of plant defenses below ground.

[Anaphylactic reaction to latex during spinal anesthesia: a case report].

Science.gov (United States)

Ueda, Narumi; Kitamura, Rie; Wakamori, Takeshi; Nakamura, Kumi; Konishi, Keisuke

2008-05-01

A 46-year-old man, with a history of atopic dermatitis and bronchial asthma, underwent surgery for an inguinal hernia. Forty-three minutes subsequent to spinal anesthesia, the patient complained suddenly of dyspnea with wheezing. Blood pressure decreased and skin eruption was observed on his chest. Postoperative laboratory tests revealed high IgE concentration, and a skin test confirmed an allergy to latex. The patient's allergic reaction was easily overlooked because of his history of bronchial asthma and the possibility that the hypotension was caused by the high spinal anesthesia. Latex allergy should be considered in any suspicious case presenting with these symptoms during surgery. After recovery, a skin test should be used to confirm the allergy to avoid repeated allergic episodes.

Plant latex lipase as biocatalysts for biodiesel production | Mazou ...

African Journals Online (AJOL)

Plant latex lipase as biocatalysts for biodiesel production. ... This paper provides an overview regarding the main aspects of latex, such as the reactions catalyzed, physiological functions, specificities, sources and their industrial applications. Keywords: Plant latex, lipase, Transesterification, purification, biodiesel ...

Ten years incidence of natural rubber latex sensitization and symptoms in a prospective cohort of health care workers using non-powdered latex gloves 2000-2009.

Science.gov (United States)

Larese Filon, Francesca; Bochdanovits, Letizia; Capuzzo, Chiara; Cerchi, Roberto; Rui, Francesca

2014-07-01

To assess the incidence of sensitization and gloves-related symptoms in 10-year follow-up in a group of health care workers (9,660 person-years) using non-powdered latex gloves from 2000 to 2009 and to examine related factors. We studied 2,053 health care workers in Trieste Hospitals by means of skin prick test for latex extract, patch tests and medical examinations. We report the incidence of latex sensitization among workers using non-powdered latex gloves. The incidence of latex sensitization, rhinitis, asthma, urticaria, irritant and allergic contact dermatitis were 1.0; 0.12; 0.21; 0.72; 2.39 and 2.50 cases per 1,000 person-years, respectively. Respiratory symptoms and urticaria were positively related with latex sensitization (OR = 8.0; 95 % CL 1.27-48.6), with common allergic respiratory symptoms (OR = 4.19; 95 % CL 1.04-16.8) and with familial atopy (OR = 4.47; 95 % CL 1.1-17.9). The incidence of latex sensitization and latex-related symptoms were very low but subjects with allergic symptoms related to common allergens are at higher risk. The use of non-latex gloves is suggested for them.

More math into Latex

CERN Document Server

Grätzer, George

2007-01-01

For close to two decades, Math into Latex has been the standard introduction and complete reference for writing articles and books containing mathematical formulas. In this fourth edition, the reader is provided with important updates on articles and books. An important new topic is discussed: transparencies (computer projections). Key features of More Math into Latex, 4th edition: Installation instructions for PC and Mac users; An example-based, visual approach and a gentle introduction with the Short Course; A detailed exposition of multiline math formulas with a Visual Guide; A unified appr

Effect of Amphiphilic Alkyl Chain Length Upon Purified LATEX Stability

International Nuclear Information System (INIS)

Amira Amir Hassan; Amir Hashim Mohd Yatim

2015-01-01

Rubber particles in purified latex (PL) are stabilized by a film of protein and fatty acid soap (surfactant). Saturated straight-chain fatty acid soaps can assist an enhancement of latex stability. However, whether the alkyl chain length plays an important role in increasing the stability is still an issue. The aim of this study is to investigate the effect of alkyl chain length of anionic surfactant on the stability of purified latex. The fatty acid soap of decanoate (9), laurate (11), sodium dodecyl sulphate (SDS) (12) and palmitate (15) were used. The numbers in parentheses indicating the number of carbon present in alkyl chain of the soap. The results showed that the impact of alkyl chain length on the stability of latex is in the order of laurate > decanoate > SDS > palmitate > purified latex accordingly. The alkyl chain length does giving a significant effect on latex stability after longer stirring time. The particle size of latex with the presence of surfactant is greater compare to a single particle itself due to extension of particles diameter. Thus suitable interaction of the nonpolar tail of surfactant with the hydrophobic regions of latex surface played a major role in maintaining a stable latex system. (author)

Involvement of Crawling and Attached Ciliates in the Aggregation of Particles in Wastewater Treatment Plants

Directory of Open Access Journals (Sweden)

Lucía Arregui

2008-01-01

Full Text Available The biological community in activated sludge wastewater plants is organized within this ecosystem as bioaggregates or flocs, in which the biotic component is embedded in a complex matrix comprised of extracellular polymeric substances mainly of microbial origin. The aim of this work is to study the role of different floc-associated ciliates commonly reported in wastewater treatment plants-crawling Euplotes and sessile Vorticella- in the formation of aggregates. Flocs, in experiments with ciliates and latex beads, showed more compactation and cohesion among particles than those in the absence of ciliates. Ciliates have been shown to contribute to floc formation through different mechanisms such as the active secretion of polymeric substances (extrusomes, their biological activities (movement and feeding strategies, or the cysts formation capacity of some species. Staining with lectins coupled to fluorescein showed that carbohydrate of the matrix contained glucose, manose, N-acetyl-glucosamine and galactose. Protein fraction revealed over the latex beads surfaces could probably be of bacterial origin, but nucleic acids represented an important fraction of the extracellular polymeric substances of ciliate origin.

Tensile properties of latex paint films with TiO2 pigment

Science.gov (United States)

Hagan, Eric W. S.; Charalambides, Maria N.; Young, Christina T.; Learner, Thomas J. S.; Hackney, Stephen

2009-05-01

The tensile properties of latex paint films containing TiO2 pigment were studied with respect to temperature, strain-rate and moisture content. The purpose of performing these experiments was to assist museums in defining safe conditions for modern paintings held in collections. The glass transition temperature of latex paint binders is in close proximity to ambient temperature, resulting in high strain-rate dependence in typical exposure environments. Time dependence of modulus and failure strain is discussed in the context of time-temperature superposition, which was used to extend the experimental time scale. Nonlinear viscoelastic material models are also presented, which incorporate a Prony series with the Ogden or Neo-Hookean hyperelastic function for different TiO2 concentrations.

The Synthesis and Modification of Nanosized Clickable Latex Particles

KAUST Repository

Almahdali, Sarah

2013-05-01

This research aims to add to the current knowledge available for miniemulsion polymerization reactions and to use this knowledge to synthesize multifunctional nanosized latex particles that have the potential to be used in catalysis. The physical properties of the latex can be adjusted to suit various environments due to the multiple functional groups present. For this research, styrene, pentafluorostyrene, azidomethyl styrene, pentafluorostyrene with azidomethyl styrene and pentafluorostyrene with styrene latexes were produced, and analyzed by dynamic light scattering. The latexes were synthesized using a miniemulsion polymerization technique found through this research. Potassium oleate and potassium 1,1,2,2,3,3,4,4-nonafluorobutane-1-sulfonate were used as surfactants during the miniemulsion polymerization reaction to synthesize pentafluorostyrene with azidomethyl styrene latex. Transmission electron microscopy data and dynamic light scattering data have been collected to analyze the structure of this latex, and it has been synthesized using a number of conditions, differing in reaction time, surfactant amount and sonication methods. We have also improved the solubility of the latex through a copper(I) catalyzed 1,3-dipolar azide-alkyne reaction, by clicking (polyethylene glycol)5000 onto the azide functional groups.

[Latex allergy in a paediatric hospital. Characteristics and risk factors].

Science.gov (United States)

Bailey, Michael; Norambuena, Ximena; Roizen, Gigia; Rodríguez, Jorge; Quezada, Arnoldo

The prevalence of latex sensitisation varies according to the population studied. There are various risk factors that increase latex sensitisation, such as genetic risk, atopy, and multiple surgeries. To characterise patients referred to an Immunology Unit with suspected latex allergy, and to analyse their clinical features and risk factors. A retrospective, descriptive study was conducted on children suspected of latex allergy. Their medical records were reviewed in order to assess symptoms with contact or exposure to latex materials. Known risk factors to latex sensitisation, such as pathologies requiring repeated surgery (spina bifida, myelomeningocele, scoliosis and nephro-urological alterations), atopy (rhinitis, asthma, atopic dermatitis) were investigated. A prick test and/or specific IgE to latex were also performed. A multivariate logistic regression model was performed to find associations between symptoms triggered by exposure to latex with underlying diseases and other risk conditions. A total of 106 patients were enrolled in the study, of whom 50 were evaluable. At diagnosis 96% of patients were older than five years. Most of the risk factors described were observable in these patients, such as multiple surgeries, neurological and nephro-urological malformations, surgery before one year-old, and repeated bladder catheterisation. After latex exposure, mucous cutaneous manifestations were the most common (52%), followed by respiratory symptoms (36%). All patients were sensitised and allergic to latex. Latex allergy is a significant problem in children with risk factors. The results shown in this study raise important challenges for preventive measures and awareness. Copyright © 2016 Sociedad Chilena de Pediatría. Publicado por Elsevier España, S.L.U. All rights reserved.

Isolation and characterization of latex-specific promoters from Papaver somniferum L.

OpenAIRE

Raymond, Michelle Jean

2004-01-01

The pharmacologically important alkaloids morphine and codeine are found in latex of opium poppy (Papaver somniferum). Latex is harbored in laticifers, a specialized vascular cell-type. Isolation and characterization of latex-specific genes may provide a useful tool to metabolically engineer increased alkaloid production. Previous research in the Nessler laboratory identified genes that exhibit latex-specific gene expression. Latex-specific genes were an 2-oxoglutarate-dioxygense (DIOX), ...

Antimicrobial activity of a 48-kDa protease (AMP48) from Artocarpus heterophyllus latex.

Science.gov (United States)

Siritapetawee, J; Thammasirirak, S; Samosornsuk, W

2012-01-01

Artocarpus heterophyllus (jackfruit) is a latex producing plant. Plant latex is produced from secretory cells and contains many intergradients. It also has been used in folk medicine. This study aimed to purify and characterize the biological activities of a protease from jackfruit latex. A protease was isolated and purified from crude latex of a jackfruit tree by acid precipitation and ion exchange chromatography. The proteolytic activities of protein were tested using gelatin- and casein-zymography. The molecular weight and isoelectric point (pl) of protein were analysed by SDS/12.5% PAGE and 2D-PAGE, respectively. Antimicrobial activity of protein was analysed by broth microdilution method. In addition, the antibacterial activity of protein against Pseudomonas aeruginosa ATCC 27853 was observed and measured using atomic force microscopy (AFM) technique. The purified protein contained protease activity by digesting gelatin- and casein-substrates. The protease was designated as antimicrobial protease-48 kDa or AMP48 due to its molecular mass on SDS-PAGE was approximately 48 kDa. The isoelectric point (pl) of AMP48 was approximately 4.2. In addition, AMP48 contained antimicrobial activities by it could inhibit the growths of Pseudomonas aeruginosa ATCC 27853 and clinical isolated Candida albicans at minimum inhibitory concentration (MIC) 2.2 mg/ml and Minimum microbicidal concentration (MMC) 8.8 mg/ml. AFM image also supported the antimicrobial activities of AMP48 by the treated bacterial morphology and size were altered from normal.

Thermodynamics of swelling of latex particles with two monomers

NARCIS (Netherlands)

Maxwell, I.A.; Kurja, J.; van Doremaele, G.H.J.; German, A.L.

1992-01-01

The partitioning of 2 monomers between the latex particle, monomer droplet, and aq. phases of an emulsion polymer latex are measured at satn. swelling of the latex particle phase (corresponding to intervals I and II of an emulsion polymn.). The monomer (Me acrylate, Bu acrylate, styrene) and polymer

Determination of cyanide and nitrate concentrations in drinking, irrigation, and wastewaters

Directory of Open Access Journals (Sweden)

Seyed Reza Mousavi

2013-01-01

Full Text Available Background: The chemical contamination of water is a major concern for the environmental and health authorities globally. Some anions present in the water are required for human health, but some of them are harmful. Free cyanide and nitrate are amongst the toxic agents in the aquatic environment. Cyanide is highly toxic for human beings. Industrial plants could be attributed to a major source of these toxic agents. Therefore, cyanide and nitrate concentrations in the drinking and irrigation water wells in the high industrial plants were evaluated. Materials and Methods: The samples (57 were taken from drinking and irrigation water wells as well as from a wastewater refinery in north of Mashhad in three stages - March 2009, June 2010, and July 2010. Determination of cyanide and nitrate were performed by a spectrophotometer using commercially available kits according to the manufacturer′s protocols. Results: Cyanide and nitrate concentrations in the drinking water samples of the three stages were 0.0050 ± 0.0007, 0.0070 ± 0.0018, 0.0008 ± 0.0014 mg/L and 6.50 ± 2.80, 7.20 ± 1.80, 7.50 ± 1.90 mg/L, respectively. Cyanide mean concentration during March, June, and July was significant (P = 0.001, whereas nitrate mean concentration was not (P = 0.5. Cyanide and nitrate concentrations in the irrigation water samples of the three stages were 0.0140 ± 0.0130, 0.0077 ± 0.0025, 0.0087 ± 0.0047 mg/L and 12.37 ± 8.12, 8.04 ± 3.99, 8.40 ± 2.60 mg/L, respectively. Cyanide (P = 0.754 and nitrate (P = 0.705 concentrations were not significant during three occasions. Cyanide and nitrate concentrations in the wastewaters of the three stages were 0.1020 ± 0.033, 0.1180 ± 0.033, 0.1200 ± 0.035 mg/L and 1633.80 ± 40.74, 279.00 ± 152.17, 298.40 ± 304.74 mg/L, respectively. Cyanide (P = 0.731 and nitrate (P = 0.187 concentration in wastewaters were not significant during different months. Conclusion: Although nitrate and cyanide concentrations in

Encapsulation of Clay Platelets inside Latex Particles

NARCIS (Netherlands)

Voorn, D.J.; Ming, W.; Herk, van A.M.; Fernando, R.H.; Sung, Li-Piin

2009-01-01

We present our recent attempts in encapsulating clay platelets inside latex particles by emulsion polymerization. Face modification of clay platelets by cationic exchange has been shown to be insufficient for clay encapsulation, leading to armored latex particles. Successful encapsulation of

Study on grafting of monomer onto natural rubber latex by radiation technique

International Nuclear Information System (INIS)

Nguyen Tan Man; Le Hai; Tran Thi Tam; Le Huu Tu, Pham Thi Sam; Dao Minh Phuong; Ha Thuc Huy

2004-01-01

Radiation vulcanization of natural rubber latex has been extensively developed through programmers assisted by the IAEA and UNDP under RCA in Asia and Pacific Region. R-D has been done in most of the Member States with technical assistance from Japan's Takasaki Radiation Chemistry Establishment. Radiation vulcanized natural rubber latex (RVNRL) has many advantages over the conventional sulfur vulcanized latex, such as absence of nitrosamine and low cytotoxicity. Radiation crosslinking is a room temperature process, itself an important cost advantage, it is easily controlled and desired extend of crosslinking is easily achieved by controlling the dose (irradiation time). Disadvantages of RVNRL to be improved are poor physical properties of film such as low tensile strength and tear strength. The research groups of Japan, Thailand and Indonesia concentrated on the improvement of physical properties of RVNRL using radiation grafted PMMA as additive [2]. F. Sundardi and W. Sofiarti have reported that tensile strength and hardness increased by radiation grafting of styrene onto NR [5]. Ono et al have reported the grafting of MMA onto NR by gamma irradiation at a dose of 5 kGy for producing thermoplastic elastomers [4]. The objective of this project is to report the results of studies of radiation graft-copolymerization of methyl methacrylate (MMA) or styrene (St) onto natural rubber latex in order to improve their physico-mechanical properties and evaluation of grafted material using Small-Angle Neutron Scattering through FNCA Project. The grafting degree of MMA and St onto NR increased with the increase of irradiation dose and monomer concentration. The alteration of grafted products structure was determined by IR method. Tensile strength, Shore A hardness, 100% modulus of grafted products increased with the increase of monomer concentration and irradiation dose while elongation at break decreased. The grafted products were characterized by Transmission Electron

Anticancer activity of flavonol and flavan-3-ol rich extracts from Croton celtidifolius latex.

Science.gov (United States)

Biscaro, Fernanda; Parisotto, Eduardo Benedetti; Zanette, Vanilde Citadini; Günther, Tania Mara Fischer; Ferreira, Eduardo Antonio; Gris, Eliana Fortes; Correia, João Francisco Gomes; Pich, Claus Tröger; Mattivi, Fulvio; Filho, Danilo Wilhelm; Pedrosa, Rozangela Curi

2013-06-01

Croton celtidifolius Baill (Euphorbiaceae) is a tree found in the Atlantic Forest in Southern Brazil, where it is commonly known as "Sangue-de-Dragão". Its red latex is used traditionally for treating ulcers, diabetes and cancer. To evaluate antitumor activities of Croton celtififolius latex in vitro and in vivo. Phytochemical analyses were conducted using HPLC-DAD-MS. Cytotoxic, nuclease and pro-apoptotic properties were determined using the tetrazolium salt assay (MTT), plasmid DNA damage assay and ethidium bromide (EB)/acridine orange methods, respectively, and antitumor activity was determined in the Ehrlich ascites carcinoma (EAC) mouse model. Phytochemical studies indicated a high phenol content of flavonols (45.67 ± 0.24 and 18.01 ± 0.23 mg/mL of myricetin and quercetin, respectively) and flavan-3-ols (114.12 ± 1.84 and 1527.41 ± 16.42 mg/L of epicatechin and epigallocatechin, respectively) in latex. These compounds reduced MCF-7 and EAC cell viability in the MTT assay (IC50 = 169.0 ± 1.8 and 187.0 ± 2.2 μg/mL, respectively). Latex compounds caused significant DNA fragmentation and increased the number of apoptotic cells (negative control (NC), 12%; latex, 41%) as indicated by differential staining in the EB/acridine orange assay. The in vivo latex treatment at 3.12 mg/kg/day reduced the body weight by 7.57 ± 2.04 g and increased median survival time to 17.5 days when compared to the NC group (13.0 days). In addition, the highest latex concentration inhibited tumor growth by 56%. These results agree with ethno-pharmacological reports showing cytotoxicity and antitumor activity of C. celtidifolius latex. The mechanism of antitumor action may be related to direct DNA fragmentation that reduces survival and induces apoptosis.

Preparation of highly stabilised natural rubber latex for radiation vulcanisation

International Nuclear Information System (INIS)

Kulatunge, S.S.; Nadarajah, M.; Kalyani, N.M.V.; Chandralal, H.N.K.K.; Devendra, R.

1996-01-01

There is a bright future for radiation vulcanised natural rubber latex (RVNRL) but there are problems in manufacturing it as the centrifuged latex to be used for radiation has to be kept for at least a month or sometimes even three to six months before adding the sensitisers and even then the latex sometimes coagulates on adding the sensitisers. This paper describes a process by which the latex can be stabilised by addition of an anionic soap before centrifuging so that it has a high mechanical stability and hence can be used even within one week of the manufacture of the centrifuged latex

Latex allergy: new insights to explain different sensitization profiles in different risk groups.

Science.gov (United States)

Peixinho, C; Tavares-Ratado, P; Tomás, M R; Taborda-Barata, L; Tomaz, C T

2008-07-01

Differences in latex allergen sensitization profiles have been described between children subjected to repetitive surgical interventions and health care workers (HCW). 'Major' allergens for patients with spina bifida are Hev b 1, 3 and 7, while for HCW, 'major' allergens are Hev b 2, 5, 6.01 and 13. The reason for these differential sensitization profiles is currently unknown. To investigate latex allergen profiles on internal and external surfaces of natural rubber latex gloves. Eighty-two samples of commonly used surgical gloves (41 glove brands) were used for analysis. Specific allergen levels of Hev b 1, 3, 5 and 6.02 on both surfaces of the gloves were quantified using an enzyme immunometric assay, a FITkit (FIT Biotech, Tampere, Finland). Differences in allergen levels were observed between internal and external surfaces of all glove types. Concentrations of Hev b 1 and Hev b 3 were significantly higher on external surfaces, while internal surfaces had higher allergen levels of Hev b 5 and Hev b 6.02. Analysis of surgical and examination gloves, powdered and nonpowdered gloves also showed that the content of Hev b 5 and Hev b 6.02 was significantly higher on internal surfaces while that of Hev b 1 and Hev b 3 was higher on external surfaces. Our study showed different allergen profiles on internal and external surfaces of natural rubber latex gloves. These results may suggest a relationship between latex allergen localization and sensitization routes in different risk groups.

Particle size, morphology and color tunable ZnO:Eu{sup 3+} nanophosphors via plant latex mediated green combustion synthesis

Energy Technology Data Exchange (ETDEWEB)

Chandrasekhar, M. [Prof. C.N.R. Rao Centre for Advanced Materials, Tumkur University, Tumkur 572 103 (India); Department of Physics, Acharya Institute of Technology, Bangalore 560 107 (India); Nagabhushana, H., E-mail: bhushanvlc@gmail.com [Prof. C.N.R. Rao Centre for Advanced Materials, Tumkur University, Tumkur 572 103 (India); Sharma, S.C. [B.S. Narayan Centre of Excellence for Advanced Materials, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); Department of Mechanical Engineering, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); Sudheer kumar, K.H. [Department of Environmental Science, Kuvempu University, Shankarghatta, Shimoga 577 451 (India); Department of Chemistry, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); B.S. Narayan Centre of Excellence for Advanced Materials, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); Dhananjaya, N. [Department of Physics, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); B.S. Narayan Centre of Excellence for Advanced Materials, B.M.S. Institute of Technology, Yelahanka, Bangalore 560 064 (India); Sunitha, D.V. [Prof. C.N.R. Rao Centre for Advanced Materials, Tumkur University, Tumkur 572 103 (India); Shivakumara, C. [Solid State and Structural Chemistry Unit, Indian Institute of Science, Bangalore 560 012 (India); Nagabhushana, B.M. [Department of Chemistry, M.S. Ramaiah Institute of Technology, Bangalore 560 054 (India)

2014-01-25

Highlights: • ZnO:Eu{sup 3+} phosphors were prepared by green synthesis route. • Morphology and particle size was tuned by varying the concentration of plant latex. • The phosphor show excellent chromaticity coordinates in the white region. -- Abstract: Efficient ZnO:Eu{sup 3+} (1–11 mol%) nanophosphors were prepared for the first time by green synthesis route using Euphorbia tirucalli plant latex. The final products were well characterized by powder X-ray diffraction (PXRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV–visible spectroscopy (UV–Vis), Fourier transform infrared spectroscopy (FTIR), etc. The average particle size of ZnO:Eu{sup 3+} (7 mol%) was found to be in the range 27–47 nm. With increase of plant latex, the particle size was reduced and porous structure was converted to spherical shaped particles. Photoluminescence (PL) spectra indicated that the peaks situated at ∼590, 615, 648 and 702 nm were attributed to the {sup 5}D{sub 0} → {sup 7}F{sub j(j=1,2,3,4)} transitions of Eu{sup 3+} ions. The highest PL intensity was recorded for 7 mol% with Eu{sup 3+} ions and 26 ml plant latex concentration. The PL intensity increases with increase of plant latex concentration up to 30 ml and there after it decreases. The phosphor prepared by this method show spherical shaped particles, excellent chromaticity co-ordinates in the white light region which was highly useful for WLED’s. Further, present method was reliable, environmentally friendly and alternative to economical routes.

EB treatment of wastewater and progress of on-going project in China

International Nuclear Information System (INIS)

Wang Zhiguang

2006-01-01

Electron beam processing has been widely used in China in the fields of radiation crosslinking cables and wires, heat shrinkable material, foam materials, irradiated latex and polymers, sterilization, removal SOx and NOx of flue gas, chemical industry, industrial CT, electron instrument, and so on. However, EB treatment of wastewater is mostly under study in laboratory. The manufacture of electron accelerators has also become a comparatively independent industry in China. (author)

Influence of wastewater characteristics on methane potential in food-processing industry wastewaters

DEFF Research Database (Denmark)

Maya Altamira, Larisa; Baun, Anders; Angelidaki, Irini

2008-01-01

) were compared to the theoretical methane yields (Bo,th) in order to evaluate the biodegradability of the tested wastewaters and the influence of their physico-chemical characteristics. The analytical method applied to quantify the wastewaters’ organic content proved to influence the estimation...... of their theoretical yields. The substrate:inoculum ratio as well as the dilution factor of the wastewaters influenced the ultimate practical methane yields differently in each of the wastewaters assessed. Substrate chemical oxygen demand (COD) concentrations did not present any influence on ultimate practical methane...... yields; on the other hand, it was found that they were affected positively by concentrations of total inorganic carbon when wastewaters were 25% and 50% diluted and affected negatively by concentrations of total acetate when wastewaters were undiluted. Carbohydrate and protein concentrations affected...

The Morphology of Emulsion Polymerized Latex Particles

Science.gov (United States)

Wignall, G. D.; Ramakrishnan, V. R.; Linne, M. A.; Klein, A.; Sperling, L. H.; Wai, M. P.; Gelman, R. A.; Fatica, M. G.; Hoerl, R. H.; Fisher, L. W.

1987-11-01

Under monomer starved feed conditions, emulsion polymerization of perdeuterated methyl methacrylate and styrene in the presence of preformed polymethylmethacrylate latexes resulted in particles with a core-shell morphology, as determined by small-angle neutron scattering (SANS) analysis for a hollow sphere. The locus of polymerization of the added deuterated monomer is therefore at the particle surface. In similar measurements a statistical copolymer of styrene and methyl methacrylate was used as seed particles for further polymerization of trideuteromethyl methacrylate. The resulting polymer latex was again shown to have a core-shell morphological structure as determined by SANS. SANS experiments were also undertaken on polystyrene latexes polymerized by equilibrium swelling methods, with deuterated polymer forming the first or second step. The experiments covered a molecular weight range of 6 x 10{sup 4} 10{sup 6} the molecular weights are consistent with the experimental errors, indicating that the deuterium labeled molecules are randomly distributed in the latex. These results led to the finding that the polymer chains were constrained in the latex particles by factors of 2 to 4 from the relaxed coil dimensions. For M molecules. Several models were examined, including the possible development of core-shell structures at lower molecular weights.

Membrane distillation for wastewater reverse osmosis concentrate treatment with water reuse potential

KAUST Repository

Naidu, Gayathri; Jeong, Sanghyun; Choi, Youngkwon; Vigneswaran, Saravanamuthu

2016-01-01

Membrane distillation (MD) was evaluated as a treatment option of wastewater reverse osmosis concentrate (WWROC) discharged from wastewater reclamation plants (WRPs). A direct contact MD (DCMD), at obtaining 85% water recovery of WWROC showed only 13–15% flux decline and produced good quality permeate (10–15 µS/cm, 99% ion rejection) at moderate feed temperature of 55 °C. Prevalent calcium carbonate (CaCO3) deposition on the MD membrane occurred in treating WWROC at elevated concentrations. The combination of low salinity and loose CaCO3 adhesion on the membrane did not significantly contribute to DCMD flux decline. Meanwhile, high organic content in WWROC (58–60 mg/L) resulted in a significant membrane hydrophobicity reduction (70% lower water contact angle than virgin membrane) attributed to low molecular weight organic adhesion onto the MD membrane. Granular activated carbon (GAC) pretreatment helped in reducing organic contents of WWROC by 46–50%, and adsorbed a range of hydrophobic and hydrophilic micropollutants. This ensured high quality water production by MD (micropollutants-free) and enhanced its reuse potential. The MD concentrated WWROC was suitable for selective ion precipitation, promising a near zero liquid discharge in WRPs.

Membrane distillation for wastewater reverse osmosis concentrate treatment with water reuse potential

KAUST Repository

Naidu, Gayathri

2016-11-29

Membrane distillation (MD) was evaluated as a treatment option of wastewater reverse osmosis concentrate (WWROC) discharged from wastewater reclamation plants (WRPs). A direct contact MD (DCMD), at obtaining 85% water recovery of WWROC showed only 13–15% flux decline and produced good quality permeate (10–15 µS/cm, 99% ion rejection) at moderate feed temperature of 55 °C. Prevalent calcium carbonate (CaCO3) deposition on the MD membrane occurred in treating WWROC at elevated concentrations. The combination of low salinity and loose CaCO3 adhesion on the membrane did not significantly contribute to DCMD flux decline. Meanwhile, high organic content in WWROC (58–60 mg/L) resulted in a significant membrane hydrophobicity reduction (70% lower water contact angle than virgin membrane) attributed to low molecular weight organic adhesion onto the MD membrane. Granular activated carbon (GAC) pretreatment helped in reducing organic contents of WWROC by 46–50%, and adsorbed a range of hydrophobic and hydrophilic micropollutants. This ensured high quality water production by MD (micropollutants-free) and enhanced its reuse potential. The MD concentrated WWROC was suitable for selective ion precipitation, promising a near zero liquid discharge in WRPs.

Composite poly(methyl methacrylate-methacrylic acid-2-hydroxyethyl methacrylate) latex for immunoassay. The case of plasminogen.

Science.gov (United States)

Miksa, B; Wilczynska, M; Cierniewski, C; Basinska, T; Slomkowski, S

1995-01-01

Poly(methyl methacrylate-methacrylic acid-2-hydroxyethyl methacrylate) latex (ACRYLAT) was synthesized by radical precipitation polymerization. The mass median diameter (MMD) and the geometrical standard deviation (GSD) of the ACRYLAT particles were 138 nm and 1.2, respectively. The concentration of the titrable carboxylic groups in the surface layer of latex particles was equal to 8.41 x 10(-6) mol m-2. Latex was able to bind up to 2.82 x 10(-7) mol of 1-aminopyrene per 1 m2 of the surface of the latex particles due to the ionic interactions between carboxylate anions and ammonium cations of protonated 1-aminopyrene. ACRYLAT was able to immobilize covalently human serum albumin in amounts up to 0.23 mg m-2. Aggregation of ACRYLAT with immobilized HSA, induced with specific antibodies (anti-HSA), was investigated turbidimetrically. The results indicated that in the model turbidimetric immunoassay, ACRYLAT coated with HSA can be used for the detection of anti-HSA in the goat anti-HSA serum diluted from 50 to 7000-fold. Immobilization of rabbit antibodies to plasminogen (anti-Plg) to ACRYLAT via the epsilon-aminocaproic acid linkers provided particles which were used for the development of the turbidimetric immunoassay for plasminogen. In this assay plasminogen could be detected in concentration ranging from 0.75 to 75 micrograms ml-1 in the blood plasma.

CHARACTERIZATION AND RECYCLING OF WASTE WATER FROM GUAYULE LATEX EXTRACTION

Science.gov (United States)

Guayule commercialization for latex production to be used in medical products and other applications is now a reality. Currently, waste water following latex extraction is discharged into evaporation ponds. As commercialization reaches full scale, the liquid waste stream from latex extraction will b...

EDITORIALS Latex allergy: 'Plight, rights and fights'

African Journals Online (AJOL)

anaphylaxis and life-threatening food allergies to cross-reacting fruit allergens such as kiwi, banana, tomato and chestnuts). Latex allergy is also encountered more frequently in children with spina bifida than in other hospitalised children.[7] Sensitisation is usually confirmed by commercial latex allergy skinprick testing or by ...

Size effects of latex nanomaterials on lung inflammation in mice

International Nuclear Information System (INIS)

Inoue, Ken-ichiro; Takano, Hirohisa; Yanagisawa, Rie; Koike, Eiko; Shimada, Akinori

2009-01-01

Effects of nano-sized materials (nanomaterials) on sensitive population have not been well elucidated. This study examined the effects of pulmonary exposure to (latex) nanomaterials on lung inflammation related to lipopolysaccharide (LPS) or allergen in mice, especially in terms of their size-dependency. In protocol 1, ICR male mice were divided into 8 experimental groups that intratracheally received a single exposure to vehicle, latex nanomaterials (250 μg/animal) with three sizes (25, 50, and 100 nm), LPS (75 μg/animal), or LPS plus latex nanomaterials. In protocol 2, ICR male mice were divided into 8 experimental groups that intratracheally received repeated exposure to vehicle, latex nanomaterials (100 μg/animal), allergen (ovalbumin: OVA; 1 μg/animal), or allergen plus latex nanomaterials. In protocol 1, latex nanomaterials with all sizes exacerbated lung inflammation elicited by LPS, showing an overall trend of amplified lung expressions of proinflammatory cytokines. Furthermore, LPS plus nanomaterials, especially with size less than 50 nm, significantly elevated circulatory levels of fibrinogen, macrophage chemoattractant protein-1, and keratinocyte-derived chemoattractant, and von Willebrand factor as compared with LPS alone. The enhancement tended overall to be greater with the smaller nanomaterials than with the larger ones. In protocol 2, latex nanomaterials with all sizes did not significantly enhance the pathophysiology of allergic asthma, characterized by eosinophilic lung inflammation and Igs production, although latex nanomaterials with less than 50 nm significantly induced/enhanced neutrophilic lung inflammation. These results suggest that latex nanomaterials differentially affect two types of (innate and adaptive immunity-dominant) lung inflammation

Laboratory Study on Possibility of Using Eichhornia To Decrease The Concentrations of Some Heavy Metals in Industrial Wastewater

International Nuclear Information System (INIS)

Alia, T.; Juniedi, H.; Salama, L.

2009-01-01

In this study Eichhornia crassipes was used under varying conditions of heavy metals concentrations, due to typical study for wastewater concentrations from the batteries factories, to decrease them. Moreover, the concentrations in different media of the plants have been distributed depending on the Response Surface design for three factors 100- 300 mg Pb/l, 15-50 mg Cd/l, 5-10 mg Mn/l which are the concentrations of heavy metals in the wastewater of batteries factories. The experiment has continued for fourteen days in which a study has been made for the current changes over the plants endurance for the different concentrations by continuing the morphologic changes which have appeared through this period. The heavy metals concentrations of the media were measured during two days. At the end of the experiment, analyses for metals were also carried out on the plant samples to determine the effect of different media on metal accumulation by roots and aerial parts of the plants. The results showed that the plant can absorb heavy metals from the industrial wastewater which is polluted by them, but at certain concentrations. It is unable to survive in a mixture of high heavy metals concentrations of these three factors together (Pb, Cd, Mn). (author)

Syntheses of crosslinked latex nanoparticles using differential microemulsion polymerization

Science.gov (United States)

Hassmoro, N. F.; Rusop, M.; Abdullah, S.

2013-06-01

The differential microemulsion polymerization was used to synthesize latex nanoparticles. In this paper, 1, 3-butylene glycol dimethacrylate (1, 3-BGDMA) was used as a crosslinker respectively 1-5 weight% of monomer total. Butyl acrylate (BA), butyl methacrylate (BMA), and methacrylic acid (MAA) was used as the monomer. The thin film of latex nanoparticles were prepared by using spin coating method and have been dried at 100°C for 5 minutes. The amount of the crosslinker added in the polymerization was optimized and we found that the particle sizes fall in the range of 30-60 nm. The structural morphology of the uncrosslinked latex represented the most homogeneous image compared to the crosslinked latex. The effect of the amount of crosslinker on the particle sizes investigated by the Zeta-sizer Nano series while Atomic Force microscopy (AFM) was used to study the structural properties of latex nanoparticles.

Syntheses of crosslinked latex nanoparticles using differential microemulsion polymerization

International Nuclear Information System (INIS)

Hassmoro, N F; Abdullah, S; Rusop, M

2013-01-01

The differential microemulsion polymerization was used to synthesize latex nanoparticles. In this paper, 1, 3-butylene glycol dimethacrylate (1, 3-BGDMA) was used as a crosslinker respectively 1–5 weight% of monomer total. Butyl acrylate (BA), butyl methacrylate (BMA), and methacrylic acid (MAA) was used as the monomer. The thin film of latex nanoparticles were prepared by using spin coating method and have been dried at 100°C for 5 minutes. The amount of the crosslinker added in the polymerization was optimized and we found that the particle sizes fall in the range of 30–60 nm. The structural morphology of the uncrosslinked latex represented the most homogeneous image compared to the crosslinked latex. The effect of the amount of crosslinker on the particle sizes investigated by the Zeta-sizer Nano series while Atomic Force microscopy (AFM) was used to study the structural properties of latex nanoparticles.

Home Healthcare Workers: How to Prevent Latex Allergies

Science.gov (United States)

... can help prevent allergic reactions for both home healthcare workers and their clients. LATEX EXPOSURE REACTIONS Three ... being used). • Inform your employer and your personal healthcare professionals that you have latex allergy. • Wear a ...

Synthesis and characterization of poly (n-butyl acrylate)-poly (methyl methacrylate) latex interpenetrating polymer networks by radiation-induced seeded emulsion polymerization

Energy Technology Data Exchange (ETDEWEB)

Yu Haibo [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Peng Jing [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China)], E-mail: jpeng@pku.edu.cn; Zhai Maolin; Li Jiuqiang; Wei Genshuan [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Qiao Jinliang [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); SINOPEC Beijing Research Institute of Chemical Industry, Beijing 100013 (China)

2007-11-15

A series of latex interpenetrating polymer networks (LIPNs) were prepared via a two-stage emulsion polymerization of methyl methacrylate (MMA) or mixture of MMA and n-butyl acrylate (n-BA) on crosslinked poly(n-butyl acrylate)(PBA) seed latex using {sup 60}Co {gamma}-ray radiation. The particles of resultant latex were produced with diameters between 150 and 250 nm. FTIR spectra identified the formation of crosslinked copolymers of PMMA or P(MMA-co-BA). Dynamic light scattering (DLS) showed that with increasing n-BA concentration in second-stage monomers, the particle size of LIPN increased. Transmission electron microscope(TEM) photographs showed that the morphology of resultant acrylate interpenetrating polymer network (IPN) latex varied from the distinct core-shell structure to homogenous particle structure with the increase of n-BA concentration, and the morphology was mainly controlled by the miscibility between crosslinked PBA seed and second-stage copolymers and polarity of P(MMA-co-BA)copolymers. In addition, differential scanning calorimeter (DSC) measurements indicated the existence of reinforced miscibility between PBA seed and P(MMA-co-BA)copolymer in prepared LIPNs.

Influence of light presence and biomass concentration on nutrient kinetic removal from urban wastewater by Scenedesmus obliquus.

Science.gov (United States)

Ruiz, J; Arbib, Z; Alvarez-Díaz, P D; Garrido-Pérez, C; Barragán, J; Perales, J A

2014-05-20

This work was aimed at studying the effect of light-darkness and high-low biomass concentrations in the feasibility of removing nitrogen and phosphorus from urban treated wastewater by the microalga Scenedesmus obliquus. Laboratory experiments were conducted in batch, where microalgae were cultured under different initial biomass concentrations (150 and 1500mgSSl(-1)) and light conditions (dark or illuminated). Nutrient uptake was more dependent on internal nutrient content of the biomass than on light presence or biomass concentration. When a maximum nitrogen or phosphorus content in the biomass was reached (around 8% and 2%, respectively), the removal of that nutrient was almost stopped. Biomass concentration affected more than light presence on the nutrient removal rate, increasing significantly with its increase. Light was only required to remove nutrients when the maximum nutrient storage capacity of the cells was reached and further growth was therefore needed. Residence times to maintain a stable biomass concentration, avoiding the washout of the reactor, were much higher than those needed to remove the nutrients from the wastewater. This ability to remove nutrients in the absence of light could lead to new configurations of reactors aimed to wastewater treatment. Copyright © 2014 Elsevier B.V. All rights reserved.

Angiogenic activity of Synadenium umbellatum Pax latex

Directory of Open Access Journals (Sweden)

PR. Melo-Reis

Full Text Available Synadenium umbellatum Pax, popularly known as "cola-nota", is a medicinal plant that grows in tropical regions. Latex of this plant is used to treat various diseases such as diabetes mellitus, Hansen´s disease, tripanosomiases, leukemia and several malignant tumors. In the present study, the angiogenic activity of S. umbellatum latex was evaluated using the chick embryo chorioallantoic membrane (CAM assay. Results showed significant increase of the vascular net (p < 0.05 compared to the negative control (H2O. The histological analysis was in accordance with the results obtained. In conclusion, our data indicate that S. umbellatum latex, under the conditions of this research, presented angiogenic effect.

Enhanced protein adsorption and patterning on nanostructured latex-coated paper.

Science.gov (United States)

Juvonen, Helka; Määttänen, Anni; Ihalainen, Petri; Viitala, Tapani; Sarfraz, Jawad; Peltonen, Jouko

2014-06-01

Specific interactions of extracellular matrix proteins with cells and their adhesion to the substrate are important for cell growth. A nanopatterned latex-coated paper substrate previously shown to be an excellent substrate for cell adhesion and 2D growth was studied for directed immobilization of proteins. The nanostructured latex surface was formed by short-wavelength IR irradiation of a two-component latex coating consisting of a hydrophilic film-forming styrene butadiene acrylonitrile copolymer and hydrophobic polystyrene particles. The hydrophobic regions of the IR-treated latex coating showed strong adhesion of bovine serum albumin (cell repelling protein), fibronectin (cell adhesive protein) and streptavidin. Opposite to the IR-treated surface, fibronectin and streptavidin had a poor affinity toward the untreated pristine latex coating. Detailed characterization of the physicochemical surface properties of the latex-coated substrates revealed that the observed differences in protein affinity were mainly due to the presence or absence of the protein repelling polar and charged surface groups. The protein adsorption was assisted by hydrophobic (dehydration) interactions. Copyright © 2014 Elsevier B.V. All rights reserved.

Seasonal variation of diclofenac concentration and its relation with wastewater characteristics at two municipal wastewater treatment plants in Turkey.

Science.gov (United States)

Sari, Sevgi; Ozdemir, Gamze; Yangin-Gomec, Cigdem; Zengin, Gulsum Emel; Topuz, Emel; Aydin, Egemen; Pehlivanoglu-Mantas, Elif; Okutman Tas, Didem

2014-05-15

The pharmaceutically active compound diclofenac has been monitored during one year at separate treatment units of two municipal wastewater treatment plants (WWTPs) to evaluate its seasonal variation and the removal efficiency. Conventional wastewater characterization was also performed to assess the possible relationship between conventional parameters and diclofenac. Diclofenac concentrations in the influent and effluent of both WWTPs were detected in the range of 295-1376 and 119-1012ng/L, respectively. Results indicated that the higher diclofenac removal efficiency was observed in summer season in both WWTPs. Although a consistency in diclofenac removal was observed in WWTP_1, significant fluctuation was observed at WWTP_2 based on seasonal evaluation. The main removal mechanism of diclofenac in the WWTPs was most often biological (55%), followed by UV disinfection (27%). When diclofenac removal was evaluated in terms of the treatment units in WWTPs, a significant increase was achieved at the treatment plant including UV disinfection unit. Based on the statistical analysis, higher correlation was observed between diclofenac and suspended solids concentrations among conventional parameters in the influent whereas the removal of diclofenac was highly correlated with nitrogen removal efficiency. Copyright © 2014 Elsevier B.V. All rights reserved.

Extractable proteins from field radiation vulcanized natural rubber latex

Energy Technology Data Exchange (ETDEWEB)

Parra, Duclerc F. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil)]. E-mail: dfparra@ipen.br; Pinto Martins, Carlos Felipe [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil); Collantes, Hugo D.C. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil); Lugao, Ademar B. [Chemical and Environmental Centre, Nuclear Energy Research Institute, Av. Lineu Prestes, 2242-CEP Sao Paulo (Brazil)

2005-07-01

The type I allergy associated with the use of natural rubber latex (NRL) products is caused by the NRL proteins leached by the sweat or other body fluids. Makuuchi's group proposed for the first time the proteins removal by the addition of water-soluble polymers (WSP) on radiation vulcanization of natural rubber latex (RVNRL) that is a promising process under development in many countries. In this study, Brazilian field natural rubber was irradiated with a {sup 60}Co gamma source to reduce the content of WSP in the final product. WSP was used as additive to improve the extraction of protein. After irradiation the RVNRL was centrifuged to extract the WSP and proteins. The analytical methodology for protein content was based on the modified Lowry method according to ASTM D5712. Protein determination was carried out in serum of latex and in the extracts of the gloves. The concentration of extractable water-soluble proteins in serum of irradiated field NRL (NRL1), not irradiated one (NRL2); of twice centrifuged sample with polymer additive NRL (NRL3) and of the glove manufactured (NRLG) are compared with commercial glove (CG). The irradiation process increases the extractable water-soluble proteins, EP, as reported in the literature. In this study the use of polymeric additive on the bi-centrifugation process to remove protein was successful and the EP of the glove obtained in NRL3 was at around 40% of the commercial glove.

Effect of arbuscular mycorrhizal and bacterial inocula on nitrate concentration in mesocosms simulating a wastewater treatment system relying on phytodepuration.

Science.gov (United States)

Lingua, Guido; Copetta, Andrea; Musso, Davide; Aimo, Stefania; Ranzenigo, Angelo; Buico, Alessandra; Gianotti, Valentina; Osella, Domenico; Berta, Graziella

2015-12-01

High nitrogen concentration in wastewaters requires treatments to prevent the risks of eutrophication in rivers, lakes and coastal waters. The use of constructed wetlands is one of the possible approaches to lower nitrate concentration in wastewaters. Beyond supporting the growth of the bacteria operating denitrification, plants can directly take up nitrogen. Since plant roots interact with a number of soil microorganisms, in the present work we report the monitoring of nitrate concentration in macrocosms with four different levels of added nitrate (0, 30, 60 and 90 mg l(-1)), using Phragmites australis, inoculated with bacteria or arbuscular mycorrhizal fungi, to assess whether the use of such inocula could improve wastewater denitrification. Higher potassium nitrate concentration increased plant growth and inoculation with arbuscular mycorrhizal fungi or bacteria resulted in larger plants with more developed root systems. In the case of plants inoculated with arbuscular mycorrhizal fungi, a faster decrease of nitrate concentration was observed, while the N%/C% ratio of the plants of the different treatments remained similar. At 90 mg l(-1) of added nitrate, only mycorrhizal plants were able to decrease nitrate concentration to the limits prescribed by the Italian law. These data suggest that mycorrhizal and microbial inoculation can be an additional tool to improve the efficiency of denitrification in the treatment of wastewaters via constructed wetlands.

Studies on physico-chemical and mechanical properties of the irradiated latex modified mortar

International Nuclear Information System (INIS)

Yassene, A.A.M.A.

2009-01-01

This thesis contains three chapter; chapter(I): Introduction and literature review on:- Introduction to polymer. - Mechanism of polymer-cement co-matrix formation.-Sulphate attack. - Solidification /stabilization of heavy metal in cement mortar. chapter(II): Materials and experimental techniques that include: 1- Preparation of latex polymer films from different polymer latices of styrene butadine rubber latex (SBR), poly (styrene-acrylic ester) latex (SAE) and vinylacetate /versatic -ester copolymer latex (C2A). The effect of γ-irradiation dose on the physico - chemical and mechanical properties of different latex polymer films was studied.2- Preparation of latex polymer-modified cement mortar with different ratios of cement: latex polymer and different curing method.3- Solidification /stabilization (S/S) of electroplating heavy metal precipitate in latex polymer- modified mortar with different cement /electroplating heavy metal sludge ratio. chapter(III) results and discussion

PS-HEMA latex fractionation by sedimentation and colloidal crystallization

Directory of Open Access Journals (Sweden)

Cardoso André H.

1999-01-01

Full Text Available A poly(styrene-co-hydroxyethylmethacrylate latex underwent sedimentation under gravity followed by an spontaneous and extensive colloidal crystallization. It was then fractionated in three visually distinguishable layers. Latex aliquots layers were sampled at different heigths and the particles were characterized by PCS, microelectrophoresis, infrared spectra and analytical electron microscopy. The major fraction was opalescent and contained the colloidal crystals settled in the bottom of the liquid. Two other latex fractions were obtained, which differed in their chemical compositions, particle sizes and topochemical features from the self-arraying particles. Macrocrystallization of the fractionated latex yielded high quality crystals with a low frequency of defects, which confirms that particle chemical homogeneity is an important factor for particle self-arraying.

Statistical Analysis Of Heavy Metals Concentration In Watermelon Plants Irrigated By Wastewater

Science.gov (United States)

Khanjani, M. J.; Maghsoudi moud, A. A.; Saffari, V. R.; Hashamipor, S. M.; Soltanizadeh, M.

2008-01-01

Concentration of heavy metals in vegetables irrigated by urban wastewater is a cause of serious concern due to the potentials health problems of consuming contaminated produce. In this study it is tried to model the concentration of heavy metals (Cd, Cr, Cu, Fe,…) as a function of their concentration in watermelon roots and stems. Our study shows there is a good relationship between them for most of collected data. By measuring the concentration in root and stem of watermelon plant samples before harvesting, the concentration of heavy metal in watermelon's fruit can be estimated by presented mathematical models. This study shows the concentrations of heavy metals in fruits, roots and stems of watermelon plants are very high and in dangerous level when irrigated by municipal waste water.

A One Year Study on the Concentrations of Norovirus and Enteric Adenoviruses in Wastewater and A Surface Drinking Water Source in Norway.

Science.gov (United States)

Grøndahl-Rosado, Ricardo C; Yarovitsyna, Ekaterina; Trettenes, Elin; Myrmel, Mette; Robertson, Lucy J

2014-12-01

Enteric viruses transmitted via the faecal-oral route occur in high concentrations in wastewater and may contaminate drinking water sources and cause disease. In order to quantify enteric adenovirus and norovirus genotypes I and II (GI and GII) impacting a drinking source in Norway, samples of surface water (52), wastewater inlet (64) and outlet (59) were collected between January 2011 and April 2012. Samples were concentrated in two steps, using an electropositive disc filter and polyethylene glycol precipitation, followed by nucleic acid extraction and analysis by quantitative polymerase chain reaction. Virus was detected in 47/52 (90.4%) of surface water, 59/64 (92%) of wastewater inlet and 55/59 (93%) of wastewater outlet samples. Norovirus GI occurred in the highest concentrations in surface water (2.51e + 04) and adenovirus in wastewater (2.15e + 07). While adenovirus was the most frequently detected in all matrices, norovirus GI was more frequently detected in surface water and norovirus GII in wastewater. This study is the first in Norway to monitor both sewage and a drinking water source in parallel, and confirms the year-round presence of norovirus and adenovirus in a Norwegian drinking water source.

Latex paint as a delivery vehicle for diethylphthalate and di-n-butylphthalate

DEFF Research Database (Denmark)

Schripp, Tobias; Salthammer, Tunga; Fauck, Christian

2014-01-01

gas-phase concentration at steady state(y). For both, DEP and DnBP, the y0 obtained was lower than the respective saturation vapor pressure (Ps). Furthermore, for both phthalates in latex paint, the material/air partition coefficient (C0/y0) was close in value to the octanol/air partition coefficient...

Synthesis and characterization of fluorinated polyacrylate latex emulsified with novel surfactants.

Science.gov (United States)

Zhang, Cuifeng; Xu, Tingting; Bao, Zhongbin; Chen, Lijun

2017-01-01

The fluorinated polyacrylate latex were successfully prepared with semi- continuous seeded emulsion polymerization of butyl acrylate (BA), methyl methacrylate (MMA) and hexafluorobutyl methacrylate (HFMA) which was initiated with potassium persulfate (KPS) initiator and emulsified with the novel mixed surfactants of sodium lauryl glutamate (SLG) and alkylphenol ethoxylates (OP-10). The structure of the resultant latex was confirmed by Fourier transform infrared spectroscopy (FTIR). The particle size of the latex was measured by Zetatrac dynamic light scattering detector. The film of latex was tested by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and contact angle (CA). The optimum conditions of preparing the novel fluorinated polyacrylate latex are optimized and the results are as follows: the amount of emulsifiers is 4.0%; mass ratio of SLG to OP-10 is 1:1, the amount of the initiator is 0.6%. The mass ratio of MMA to BA is 1:1 and the amount of HFMA is 7.0%. In this case, the conversion is high and the polymerization stability is good. In addition, the water resistance and thermal properties of the latex films were improved significantly in comparison with the film of the latex prepared without the fluorinated monomer.

Plant latex: a promising antifungal agent for post harvest disease control.

Science.gov (United States)

Sibi, G; Wadhavan, Rashmi; Singh, Sneha; Shukla, Abhilasha; Dhananjaya, K; Ravikumar, K R; Mallesha, H

2013-12-01

Bioactive compounds from plant latex are potential source of antifungic against post harvest pathogens. Latex from a total of seven plant species was investigated for its phytochemical and antifungal properties. Six fungi namely Aspergillus fumigatus, A. niger, A. terreus, F. solani, P. digitatum and R. arrhizus were isolated from infected fruits and vegetables and tested against various solvent extracts of latex. Analysis of latex extracts with phytochemical tests showed the presence of alkaloids, flavonoids, glycosides, phenols, saponins, steroids, tannins and terpenoids. Antifungal assay revealed the potential inhibitory activity of petroleum ether extracts against the postharvest fungal isolates. Various degree of sensitivity was observed irrespective of plant species studied with A. terreus and P. digitatum as the most susceptible ones. F. solani and A. fumigatus were moderately sensitive to the latex extracts tested. Among the plants, latex of Thevetia peruviana (75.2%) and Artocarpus heterophyllus (64.8%) were having potential antifungal activity against the isolates followed by Manilkara zapota (51.1%). In conclusion, use of plant latex makes interest to control postharvest fungal diseases and is fitting well with the concept of safety for human health and environment.

Drying of latex films and coatings: Reconsidering the fundamental mechanisms

DEFF Research Database (Denmark)

Kiil, Søren

2006-01-01

The two existing theories describing drying of latex films or coatings are reconsidered. Subsequently, a novel mathematical drying model is presented, the simulations of which can match and explain experimental drying rate data of two previous investigations with latex films. In contrast to previ......The two existing theories describing drying of latex films or coatings are reconsidered. Subsequently, a novel mathematical drying model is presented, the simulations of which can match and explain experimental drying rate data of two previous investigations with latex films. In contrast...... to previous model studies, but in agreement with observations, simulations suggest that during the falling rate period of the drying process of a latex film, a porous skin of partly coalesced latex particles is indeed formed, which limits transport of water vapour from the receding air-liquid interphase...... to the surface of the film. The value of the effective diffusion coefficient of water vapour in the dry and partly coalesced layer (7 x 10(-7) m(2)/s at 19-24 degrees C), the adjustable parameter of the model for the falling rate period, was found to be independent of initial wet film thickness (89-1322 mu m...

Regional variability in bed-sediment concentrations of wastewater compounds, hormones and PAHs for portions of coastal New York and New Jersey impacted by hurricane Sandy

Science.gov (United States)

Phillips, Patrick J.; Gibson, Cathy A; Fisher, Shawn C.; Fisher, Irene; Reilly, Timothy J.; Smalling, Kelly L.; Romanok, Kristin M.; Foreman, William T.; ReVello, Rhiannon C.; Focazio, Michael J.; Jones, Daniel K.

2016-01-01

Bed sediment samples from 79 coastal New York and New Jersey, USA sites were analyzed for 75 compounds including wastewater associated contaminants, PAHs, and other organic compounds to assess the post-Hurricane Sandy distribution of organic contaminants among six regions. These results provide the first assessment of wastewater compounds, hormones, and PAHs in bed sediment for this region. Concentrations of most wastewater contaminants and PAHs were highest in the most developed region (Upper Harbor/Newark Bay, UHNB) and reflected the wastewater inputs to this area. Although the lack of pre-Hurricane Sandy data for most of these compounds make it impossible to assess the effect of the storm on wastewater contaminant concentrations, PAH concentrations in the UHNB region reflect pre-Hurricane Sandy conditions in this region. Lower hormone concentrations than predicted by the total organic carbon relation occurred in UHNB samples, suggesting that hormones are being degraded in the UHNB region.

Semipermeable membrane devices concentrate mixed function oxygenase inducers from oil sands and refinery wastewaters

International Nuclear Information System (INIS)

Parrott, J.L.; Hewitt, L.M.

2002-01-01

The health of fish in the Athabasca River was examined to determine the effects of both natural and anthropogenic oil sands exposure on liver mixed function oxygenase (MFO) enzymes. Semipermeable membrane devices (SPMD) were used to concentrate bioavailable compounds that may result in MFO induction. The SPMDs were used for a period of 2 weeks in the Steepbank River as well as in oil refinery wastewater and intake ponds. They were then tested to see if they induced ethoxyresorufin-O-deethylase (EROD) activity in hepatoma cells, a cell line derived from a liver cancer of a small fish. SPMDs from the wastewater pond contained potent EROD inducers in fish liver cells. SPMDs from the Athabasca River exhibited some EROD inducers, but they were 1/100 as potent as those of the refinery wastewater. The characteristics of MFO inducers from refinery wastewater were different from natural inducers from the oil sands in the Athabasca and Steepbank Rivers. For instance, log Kow was less than 5 for refinery wastewater, but it was greater than 5 for Athabasca River wastewater and from natural oil sands exposure. In the case of the Steepbank River, the pattern of MFO induction was similar to the MFO induction seen in wild fish.The highest MFO inducers were found to be in the area of the mine, suggesting and anthropogenic pollution source. The less potent inducers were in the area of the natural and undisturbed oil sands. Very few inducers were found outside of the oil sands formation

Study on Relationship between Seasonal Temperatures and Municipal Wastewater Pollutant Concentration and Removal Rate

Directory of Open Access Journals (Sweden)

Yuan Shaoxiong

2016-01-01

Full Text Available In this study, the temperatures, pollutant concentrations and other indicators of municipal wastewater influent and effluent were tested for 7 months in 6 constructed wetland microcosms; the hydraulic retention time is 2 days. The results indicated that for both influent and effluent, there was a highly significant negative correlation (P<0.01 between the temperature and the pollutant concentrations, there was a significant difference (P<0.05 between seasonal temperatures, and the pollutant concentrations in summer and autumn were significantly different from those in winter (P<0.05. Furthermore, a regression analysis of pollutant concentration (y based on changes in water temperature (x in different seasons was performed. The analysis revealed that the relationship has the form ‘y = a -bx + cx2’, that under certain circumstances, pollutant concentrations can be calculated based on the temperature, and that the concentrations of NH4-N, Total Phosphorus (TP and Soluble Reactive Phosphorus (SRP had a significantly negative correlation with their removal rate (P < 0.01. However, seasonal temperature clearly did not have a direct impact on the pollutant concentration, and some studies have indicated that the different manners in which urban residents use water as the temperature changes may be the real reason that the pollutant concentrations of municipal wastewater vary with seasonal temperature. Furthermore, when designing and operating constructed wetlands, the impact of the changes in pollutant concentrations generated by seasonal temperature should be fully considered, dilution and other means should be taken to ensure purification.

A Reappraisal of Online Mathematics Teaching Using LaTeX

Directory of Open Access Journals (Sweden)

Eamon Costello

2009-12-01

Full Text Available The mathematics language LaTeX is often seen outside of academic circles as a legacy technology that is awkward to use. MathML - a verbose language designed for data-exchange, and to be written and understood by machines - is sometimes by contrast seen as something that will aid online mathematics and lack of browser support for it bemoaned. However LaTeX can already do many of the things that MathML might promise. LaTeX is here proposed as a language from which small fragments, with concise syntax, can be used by people to easily create and share mathematical expressions online. The capability to embed fragments of LaTeX code in online discussions is described here and its impact on a group of educators and learners evaluated. Here LaTeX is posited as a useful tool for facilitating asynchronous, online, collaborative learning of mathematics.

Thrombin like activity of Asclepias curassavica L. latex: action of cysteine proteases.

Science.gov (United States)

Shivaprasad, H V; Rajesh, R; Nanda, B L; Dharmappa, K K; Vishwanath, B S

2009-05-04

To validate the scientific basis of plant latex to stop bleeding on fresh cuts. Cysteine protease(s) from Asclepias curassavica (Asclepiadaceae) plant latex was assessed for pro-coagulant and thrombin like activities. A waxy material from the latex of Asclepias curassavica latex was removed by freezing and thawing. The resulted latex enzyme fraction was assayed for proteolytic activity using denatured casein as substrate. Its coagulant activity and thrombin like activity were determined using citrated plasma and pure fibrinogen, respectively. Inhibition studies were performed using specific protease inhibitors to know the type of protease. The latex enzyme fraction exhibited strong proteolytic activity when compared to trypsin and exerted pro-coagulant action by reducing plasma clotting time from 195 to 58 s whereas trypsin reduced clotting time marginally from 195 to 155 s. The pro-coagulant activity of this enzyme fraction was exerted by selectively hydrolyzing A alpha and B beta subunits of fibrinogen to form fibrin clot when pure fibrinogen was used as substrate as assessed by fibrinogen-agarose plate method and fibrinogen polymerization assay. Trypsin failed to induce any fibrin clot under similar conditions. The electrophoretic pattern of latex enzyme fraction-induced fibrin clot was very much similar to that of thrombin-induced fibrin clot and mimic thrombin like action. The proteolytic activity including thrombin like activity of Asclepias curassavica latex enzyme fraction was completely inhibited by iodoaceticacid (IAA). Cysteine proteases from Asclepias curassavica latex exhibited strong pro-coagulant action and were found to be specific in its action (Thrombin like). This could be the basis for the use of plant latex in pharmacological applications that justify their use as folk medicine.

Characterization of livestock wastewater at various stages of wastewater treatment plant

International Nuclear Information System (INIS)

Ting Teo Ming; Kim, Tak Hyun; Lee, Myun Joo

2007-01-01

A characterization study has been conducted at Gongju Livestock Wastewater Treatment Plant, Gongju, South Korea. It is owned and operated by the government with treatment capacity of 250 tons per day. Livestock wastewater was collected from individual farmer and treated at the treatment plant. The centralized livestock wastewater treatment plant has various treatment processes namely pre-treatment, anaerobic digestion, nitrification, de-nitrification , chemical treatment, sand filtration and ozonization. The livestock wastewater was characterized by high COD, SS, T-N and T-P with concentration of 20600 mg/l, 6933 mg/l, 2820 mg/l and 700 mg/ l, respectively. After the wastewater has undergone various treatment processes it was discharged to waterways with concentration of COD, SS, T-N and T-P at 105 mg/l, 73 mg/l, 2.1 mg/l and 9 mg/l, respectively. This is part of the study to investigate the potential of irradiation to be applied at the centralized livestock wastewater treatment plant. Although livestock wastewater can be potentially applied to crop as source of nutrients it also affect the water quality due to runoff and leaching. When the wastewater applied at the rates in excess of crop uptake rates, the excess wastewater could potentially enter surface and groundwater and polluted them. (author)

Alergia látex-fruta Latex-fruit allergy

Directory of Open Access Journals (Sweden)

Flávia Andréia MARIN

2002-01-01

Full Text Available O látex está sendo considerado o alergênico do ano 2000, tendo em vista que inúmeros indivíduos, principalmente profissionais da área de saúde e pacientes submetidos a várias intervenções diagnósticas e terapêuticas, estão freqüentemente expostos aos alérgenos do látex, presentes em produtos de borracha natural. As manifestações clínicas conseqüentes às reações alérgicas de hipersensibilidade imediata vão desde rinite, urticária, conjuntivite, angioedema, asma, até anafilaxia. Estudos recentes estão demonstrando que pacientes alérgicos ao látex desenvolvem concomitantemente sensibilização a certos alimentos de origem vegetal, especialmente frutas como papaia, figo, banana, abacate, kiwi, pêssego, abacaxi, melão e castanha, acreditando-se numa provável ocorrência de reações cruzadas entre os alérgenos do látex e destas frutas. Faz-se, então, uma revisão sobre a alergia ao látex, em particular sobre os grupos de risco, incluindo a presença de reatividade cruzada entre o látex e as frutas.The latex is being considered the allergenic agent of the year 2000, taking into account that several individuals, mainly health care professionals, and patients who had undergone many diagnostic and therapeutic interventions, are frequently exposed to latex allergens, which are present in natural rubber latex products. The clinical manifestations, derived from allergic reactions of immediate hypersensitivity vary from since rhinitis, conjunctivitis, urticaria, angioedema, asthma, to anaphylaxis. Recent researches are demonstrating that patients allergic to latex develop concomitantly sensitization to certain vegetable foods, especially fruits like papaya, fig, banana, avocado, kiwi, peach, pineapple, melon and chestnut, and a probable occurrence of cross reaction between allergens of latex and of these fruits is believed. A review is made about latex allergy, in particular about risk groups, including the presence of

Pilot Scale Production of Irradiated Natural Rubber Latex and its Dipping Products

Directory of Open Access Journals (Sweden)

M. Utama

2005-07-01

Full Text Available One hundred and fifty kg natural rubber latex (NRL before and after concentration were added with 3 phr (part hundred ratio of rubber normal butyl acrylate, then the mixture were irradiated at 25 kGy by gamma rays of 60Co in pilot scale. The irradiated natural rubber latex (INRL were then being to use for producing rubber products such as condom, surgical gloves, and spygmomanometer in factory scale. The quality of INRL and rubber products such as : total solid content (TSC, dry rubber content (DRC, KOH, VFA and MST number, tensile strength, modulus, elongation at break, extractable protein content, and response against Type I allergy etc. were evaluated. The economic aspect for producing INRL by means of Gamma Irradiator (GI and Electron Beam Machine (EBM such as payback period (PP, net present value (NPV and internal rate return (IRR were calculated. The results showed that the latex properties of INRL such as DRC, TSC, KOH, VFA, and MST number are not only found to the requirement of the ISO 2004 standard but also the latex has low protein, lipid, and carbohydrate content. The physical and mechanical properties (tensile strength, modulus, and elongation at break of rubber dipping products such as condom, gloves, and sphygmomanometer are not only found to the requirement of ISO 4074, ISO 10282, and ANSI/AAMI SP-1994 standards, but also the allergic response tested clinical latex-sensitive protein allergen by ELISA test on gloves, and by SPT test on condom are found to be negative. It indicates that production of INRL or PVNRL or RVNRL by EBM 250 keV/10 mA, was more cheap than by using gamma γ irradiator 200 kCi, or sulfur vulcanization. The value of PBP (payback period was 2,1 years, NPV (net present value was 4,250 US $, PI (profitability index 1,06 and IRR (internal rate of returns was 25,0%.

Structure and dynamics of concentrated dispersions of polystyrene latex spheres in glycerol: Static and dynamic x-ray scattering

International Nuclear Information System (INIS)

Lumma, D.; Lurio, L. B.; Borthwick, M. A.; Falus, P.; Mochrie, S. G. J.

2000-01-01

X-ray photon correlation spectroscopy and small-angle x-ray scattering measurements are applied to characterize the dynamics and structure of concentrated suspensions of charge-stabilized polystyrene latex spheres dispersed in glycerol, for volume fractions between 2.7% and 52%. The static structures of the suspensions show essentially hard-sphere behavior. The short-time dynamics shows good agreement with predictions for the wave-vector-dependent collective diffusion coefficient, which are based on a hard-sphere model [C. W. J. Beenakker and P. Mazur, Physica A 126, 349 (1984)]. However, the intermediate scattering function is found to violate a scaling behavior found previously for a sterically stabilized hard-sphere suspension [P. N. Segre and P. N. Pusey, Phys. Rev. Lett. 77, 771 (1996)]. Our measurements are parametrized in terms of a viscoelastic model for the intermediate scattering function [W. Hess and R. Klein, Adv. Phys. 32, 173 (1983)]. Within this framework, two relaxation modes are predicted to contribute to the decay of the dynamic structure factor, with mode amplitudes depending on both wave vector and volume fraction. Our measurements indicate that, for particle volume fractions smaller than about 0.30, the intermediate scattering function is well described in terms of single-exponential decays, whereas a double-mode structure becomes apparent for more concentrated systems

Microwave enhanced Fenton-like process for the treatment of high concentration pharmaceutical wastewater

International Nuclear Information System (INIS)

Yang Yu; Wang Peng; Shi Shujie; Liu Yuan

2009-01-01

This paper explored a novel process for wastewater treatment, i.e. microwave enhanced Fenton-like process. This novel process was introduced to treat high concentration pharmaceutical wastewater with initial COD loading of 49,912.5 mg L -1 . Operating parameters were investigated and the optimal condition included as follows: microwave power was 300 W, radiation time was 6 min, initial pH was 4.42, H 2 O 2 dosage was 1300 mg L -1 and Fe 2 (SO 4 ) 3 dosage was 4900 mg L -1 , respectively. Within the present experimental condition used, the COD removal and UV 254 removal reached to 57.53% and 55.06%, respectively, and BOD 5 /COD was enhanced from 0.165 to 0.470. The variation of molecular weight distribution indicated that both macromolecular substances and micromolecular substances were eliminated quite well. The structure of flocs revealed that one ferric hydrated ion seemed to connect with another ferric hydrated ion and/or organic compound molecule to form large-scale particles by means of van der waals force and/or hydrogen bond. Subsequently, these particles aggregated to form flocs and settled down. Comparing with traditional Fenton-like reaction and conventional heating assisted Fenton-like reaction, microwave enhanced Fenton-like process displayed superior treatment efficiency. Microwave was in favor of improving the degradation efficiency, the settling quality of sludge, as well as reducing the yield of sludge and enhancing the biodegradability of effluent. Microwave enhanced Fenton-like process is believed to be a promising treatment technology for high concentration and biorefractory wastewater.

Rapid and efficient treatment of wastewater with high-concentration heavy metals using a new type of hydrogel-based adsorption process.

Science.gov (United States)

Zhou, Guiyin; Liu, Chengbin; Chu, Lin; Tang, Yanhong; Luo, Shenglian

2016-11-01

In this study, a new type of double-network hydrogel sorbent was developed to remove heavy metals in wastewater. The amino-functionalized Starch/PAA hydrogel (NH2-Starch/PAA) could be conducted in a wide pH and the adsorption process could rapidly achieve the equilibrium. The adsorption capacity got to 256.4mg/g for Cd(II). Resultantly, even though Cd(II) concentration was as high as 180mg/L, the Cd(II) could be entirely removed using 1g/L sorbent. Furthermore, the desirable mechanical durability of the adsorbent allowed easy separation and reusability. In the fixed-bed column experiments, the treatment volume of the effluent with a high Cd(II) concentration of 200mg/L reached 2400BV (27.1L) after eight times cycle. The NH2-Starch/PAA overcame the deficiency of conventional sorbents that could not effectively treat the wastewater with relatively high metal concentrations. This work provides a new insight into omnidirectional enhancement of sorbents for removing high-concentration heavy metals in wastewater. Copyright © 2016 Elsevier Ltd. All rights reserved.

Radiation vulcanization of natural rubber latex sensitized with commercial gases

International Nuclear Information System (INIS)

Chirinos, H.; Lugao, A.

2002-01-01

The industrial activities using natural rubber latex are fully compatible with rural areas in Amazon and other places in Brazil, as well as in other tropical countries. However the classical sulfur vulcanization presents many occupational problems for the workers in rural areas. Radiation vulcanization of natural rubber latex is a much more friendly process as sulfur compounds are not needed for crosslinking, although chemicals as acrylate monomers, particularly multifunctional acrylates are still used as sensitizers for radiation processes. Two commercial gases, acetylene and butadiene, were selected as sensitizers for the radiation vulcanization of natural rubber latex instead of acrylates. These gases accelerate the crosslinking rates of the cure process and lower the radiation dose required to achieve vulcanization of natural rubber latex and improve the mechanical properties to reduce the tackiness of rubber goods. (author)

Radiation vulcanization of natural rubber latex sensitized with commercial gases

Energy Technology Data Exchange (ETDEWEB)

Chirinos, H.; Lugao, A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

2002-07-01

The industrial activities using natural rubber latex are fully compatible with rural areas in Amazon and other places in Brazil, as well as in other tropical countries. However the classical sulfur vulcanization presents many occupational problems for the workers in rural areas. Radiation vulcanization of natural rubber latex is a much more friendly process as sulfur compounds are not needed for crosslinking, although chemicals as acrylate monomers, particularly multifunctional acrylates are still used as sensitizers for radiation processes. Two commercial gases, acetylene and butadiene, were selected as sensitizers for the radiation vulcanization of natural rubber latex instead of acrylates. These gases accelerate the crosslinking rates of the cure process and lower the radiation dose required to achieve vulcanization of natural rubber latex and improve the mechanical properties to reduce the tackiness of rubber goods. (author)

Nitrification of an industrial wastewater in a moving-bed biofilm reactor: effect of salt concentration.

Science.gov (United States)

Vendramel, Simone; Dezotti, Marcia; Sant'Anna, Geraldo L

2011-01-01

Nitrification of wastewaters from chemical industries can pose some challenges due to the presence of inhibitory compounds. Some wastewaters, besides their organic complexity present variable levels of salt concentration. In order to investigate the effect of salt (NaCl) content on the nitrification of a conventional biologically treated industrial wastewater, a bench scale moving-bed biofilm reactor was operated on a sequencing batch mode. The wastewater presenting a chloride content of 0.05 g l(-1) was supplemented with NaCl up to 12 g Cl(-) l(-1). The reactor operation cycle was: filling (5 min), aeration (12 or 24h), settling (5 min) and drawing (5 min). Each experimental run was conducted for 3 to 6 months to address problems related to the inherent wastewater variability and process stabilization. A PLC system assured automatic operation and control of the pertinent process variables. Data obtained from selected batch experiments were adjusted by a kinetic model, which considered ammonia, nitrite and nitrate variations. The average performance results indicated that nitrification efficiency was not influenced by chloride content in the range of 0.05 to 6 g Cl(-) l(-1) and remained around 90%. When the chloride content was 12 g Cl(-) l(-1), a significant drop in the nitrification efficiency was observed, even operating with a reaction period of 24 h. Also, a negative effect of the wastewater organic matter content on nitrification efficiency was observed, which was probably caused by growth of heterotrophs in detriment of autotrophs and nitrification inhibition by residual chemicals.

An integrated membrane bioreactor - nanofiltration concept with concentrate recirculation for wastewater treatment and nutrient recovery

NARCIS (Netherlands)

Kappel, C.

2014-01-01

Increasing water shortages drive the need for water reuse. Membranes are a very suitable technology for purification of wastewater. Membrane bioreactor (MBR) permeate can be polished by nanofiltration (NF), allowing the production of high quality reusable water. The NF concentrate potentially is an

Antimicrobial activity of latex silver nanoparticles using Calotropis procera

Directory of Open Access Journals (Sweden)

Nadia Hussein Mohamed

2014-11-01

Conclusions: It can be concluded that serum latex of Calotropis procera was found to display strong potential for the synthesis of AgNPs as antimicrobial agents through rapid reduction of silver ions (Ag+ to Ag0. The green synthesized AgNPs were found to show higher antimicrobial efficacy than crude latex.

Immune response modulation by curcumin in a latex allergy model

Directory of Open Access Journals (Sweden)

Raju Raghavan

2007-01-01

Full Text Available Abstract Background There has been a worldwide increase in allergy and asthma over the last few decades, particularly in industrially developed nations. This resulted in a renewed interest to understand the pathogenesis of allergy in recent years. The progress made in the pathogenesis of allergic disease has led to the exploration of novel alternative therapies, which include herbal medicines as well. Curcumin, present in turmeric, a frequently used spice in Asia has been shown to have anti-allergic and inflammatory potential. Methods We used a murine model of latex allergy to investigate the role of curcumin as an immunomodulator. BALB/c mice were exposed to latex allergens and developed latex allergy with a Th2 type of immune response. These animals were treated with curcumin and the immunological and inflammatory responses were evaluated. Results Animals exposed to latex showed enhanced serum IgE, latex specific IgG1, IL-4, IL-5, IL-13, eosinophils and inflammation in the lungs. Intragastric treatment of latex-sensitized mice with curcumin demonstrated a diminished Th2 response with a concurrent reduction in lung inflammation. Eosinophilia in curcumin-treated mice was markedly reduced, co-stimulatory molecule expression (CD80, CD86, and OX40L on antigen-presenting cells was decreased, and expression of MMP-9, OAT, and TSLP genes was also attenuated. Conclusion These results suggest that curcumin has potential therapeutic value for controlling allergic responses resulting from exposure to allergens.

Organic contaminants in onsite wastewater treatment systems

Science.gov (United States)

Conn, K.E.; Siegrist, R.L.; Barber, L.B.; Brown, G.K.

2007-01-01

Wastewater from thirty onsite wastewater treatment systems was sampled during a reconnaissance field study to quantify bulk parameters and the occurrence of organic wastewater contaminants including endocrine disrupting compounds in treatment systems representing a variety of wastewater sources and treatment processes and their receiving environments. Bulk parameters ranged in concentrations representative of the wide variety of wastewater sources (residential vs. non-residential). Organic contaminants such as sterols, surfactant metabolites, antimicrobial agents, stimulants, metal-chelating agents, and other consumer product chemicals, measured by gas chromatography/mass spectrometry were detected frequently in onsite system wastewater. Wastewater composition was unique between source type likely due to differences in source water and chemical usage. Removal efficiencies varied by engineered treatment type and physicochemical properties of the contaminant, resulting in discharge to the soil treatment unit at ecotoxicologically-relevant concentrations. Organic wastewater contaminants were detected less frequently and at lower concentrations in onsite system receiving environments. Understanding the occurrence and fate of organic wastewater contaminants in onsite wastewater treatment systems will aid in minimizing risk to ecological and human health.

Capacitance Regression Modelling Analysis on Latex from Selected Rubber Tree Clones

International Nuclear Information System (INIS)

Rosli, A D; Baharudin, R; Hashim, H; Khairuzzaman, N A; Mohd Sampian, A F; Abdullah, N E; Kamaru'zzaman, M; Sulaiman, M S

2015-01-01

This paper investigates the capacitance regression modelling performance of latex for various rubber tree clones, namely clone 2002, 2008, 2014 and 3001. Conventionally, the rubber tree clones identification are based on observation towards tree features such as shape of leaf, trunk, branching habit and pattern of seeds texture. The former method requires expert persons and very time-consuming. Currently, there is no sensing device based on electrical properties that can be employed to measure different clones from latex samples. Hence, with a hypothesis that the dielectric constant of each clone varies, this paper discusses the development of a capacitance sensor via Capacitance Comparison Bridge (known as capacitance sensor) to measure an output voltage of different latex samples. The proposed sensor is initially tested with 30ml of latex sample prior to gradually addition of dilution water. The output voltage and capacitance obtained from the test are recorded and analyzed using Simple Linear Regression (SLR) model. This work outcome infers that latex clone of 2002 has produced the highest and reliable linear regression line with determination coefficient of 91.24%. In addition, the study also found that the capacitive elements in latex samples deteriorate if it is diluted with higher volume of water. (paper)

Natural membranes of Hevea brasiliensis latex as delivery system for Casearia sylvestris leaf components

Directory of Open Access Journals (Sweden)

Flávio A. Carvalho

Full Text Available ABSTRACT Natural latex from Hevea brasiliensis (Wild. ex A.Juss Müll.Arg., Euphorbiaceae, showed angiogenic action and Casearia sylvestris Sw., Salicaceae, leaf derivatives presented anti-inflammatory and wound healing activities. Therefore, an association of these effects was interesting for wound healing applications. The aims of this study were the development of membranes of natural latex incorporated with C. sylvestris leaf derivatives (ethanolic extract, diterpene concentrated fraction and casearin J, their chemical and physical characterization, and the evaluation of in vitro skin permeation and retention of C. sylvestris bioactive secondary metabolites (diterpenes and phenolic compounds. The membranes were developed mixing hydroethanolic solutions of C. sylvestris derivatives with latex and drying them in a desiccator. They were characterized by infrared spectroscopy, scanning electron microscopy, water vapor permeability and mechanical resistance assays, demonstrating that all membranes were permeable, resistant and homogeneous in surfaces. The permeation and retention assays demonstrated dermal penetration of phenolic compounds for ethanolic extract membrane and of casearin-like clerodane diterpenes for all membranes, indicating that these membranes have great potential for therapeutical application as a topical system for C. sylvestris components releasing.

Decontamination of latex gloves; Decontamination de gants en latex

Energy Technology Data Exchange (ETDEWEB)

Boutot, P; Schipfer, P; Blachere, A [Commissariat a l' Energie Atomique, Chusclan (France). Centre de Production de Plutonium de Marcoule

1969-07-01

Initially the latex gloves used in controlled zones were processed after use as radioactive waste. In view of the continually increasing number used, however, the persons in charge of the SPRAR have considered the possibility of decontaminating the gloves and using them again after control. The recovery installations which have been developed were initially designed rather crudely and operated irregularly; they have been progressively improved as a result of the experience acquired; today they are more really an industrial concern, equipped with automatic machinery. In 1967 it has been possible with this set-up to recover 247000 pairs of gloves, representing nearly 70 per cent of the number treated. (author) [French] Initialement, les gants de latex utilises dans les zones controlees etaient conditionnes apres emploi comme dechets radioactifs. Mais, devant l'augmentation sans cesse croissante des quantites employees, les responsables du SPRAR ont envisage leur decontamination et leur recyclage apres controles. Les installations de recuperation mises au point, de conception artisanale et fonctionnant de maniere episodique au depart, se sont progressivement ameliorees au fur et a mesure de l'experience acquise; elles revetent aujourd'hui le caractere d'une exploitation industrielle equipee de machines automatiques. En 1967, ces nouvelles installations ont permis de recuperer 247000 paires de gants, ce qui represente pres de 70 pour cent des quantites traitees. (auteur)

Follow-up Study of Latex-allergic Health Care Workers in Japan

Directory of Open Access Journals (Sweden)

Akiko Yagami

2006-01-01

Conclusions: After avoiding latex products and following our educational suggestions, the patients' allergy symptoms had generally improved. This indicates that our countermeasures against latex allergy were largely successful.

Morphology and film formation of poly(butyl methacrylate)-polypyrrole core-shell latex particles

NARCIS (Netherlands)

Huijs, F; Lang, J

Core-shell latex particles made of a poly(butyl methacrylate) (PBMA) core and a thin polypyrrole (PPy) shell were synthesized by two-stage polymerization. In the first stage, PBMA latex particles were synthesized in a semicontinuous process by free-radical polymerization. PBMA latex particles were

Preparation and Characterization of Conducting Polymer Latices by Chemical Polymerization of Aniline or Anisidine in Presence of Latex: Study of Their Electroactivity and Anti-Corrosion Properties

Directory of Open Access Journals (Sweden)

Bakhshali Massoumi

2013-06-01

Full Text Available Poly (vinylacetate-co-butylmethacrylate was prepared in presence of potassium persulphate as an oxidizing agent in aqueous solution of dodecylbenzene sulfonate sodium as an emulsifying agent. Then, aniline was polymerized by chemical oxidation method at three different concentrations of aniline monomer (0.1, 0.2 and 0.3 M in toluene in presence of poly(vinylacetate-co-butylmethacrylate in order to obtain polyaniline/poly(vinylacetate-co-butylmethacrylate. To prepare conducting-latex of polyanisidine/poly(vinylacetate-co-butylmethacrylate the same method was employed as above for aniline monomer in obtaining conducting polyaniline/poly(vinylacetate-co-butylmethacrylate latex. In addition, the purification of conducting-latex polymers, polyaniline/poly(vinylacetate-co-butylmethacrylate and polyanisidine/poly(vinylacetate-co-butylmethacrylate was conducted and preparation of tin layer films of conducting-latex polymers was carried out by casting method on glassy lames. The electroactivity properties of the prepared latex-polymers, polyaniline/poly(vinylacetate-co-butylmethacrylate and polyanisidine/poly(vinylacetate-co-butylmethacrylate were investigated by cyclic voltammetery (CV. The voltamogrames showed that the latex films were electroactive. Because of conductivity and electroactivity, the obtained films may find applications in anti-corrosion coatings. The anti-corrosion properties of conducting-latex polymers were studied on aluminum surface by impedance technique. The structure of the prepared conducting-latex polymers was confirmed by Fourier transform infrared (FTIR. Finally, the electrical conductivity of synthesized conducting-latex polymers, polyaniline/poly(vinylacetate-co-butylmethacrylate and polyanisidine/poly(vinylacetate-co-butylmethacrylate was measured by four probe technique.

Latex allergies - for hospital patients

Science.gov (United States)

... ency/patientinstructions/000499.htm Latex allergies - for hospital patients To use the sharing features on this page, ... ADAM Health Solutions. About MedlinePlus Site Map FAQs Customer Support Get email updates Subscribe to RSS Follow ...

Installing fonts in LaTeX a user's experience

NARCIS (Netherlands)

Hanssen, F.T.Y.

2003-01-01

This paper presents a user's experience with installing fonts for use in LaTeX. It will be shown that it is not hard to make a standard Type 1 font work, if you use modern font installation software for LaTeX. All the steps necessary to install the example fonts will be shown. The example fonts used

Radioactive iodine (125I) labeling of latex particles

International Nuclear Information System (INIS)

Parikh, G.C.; Ho, C.K.

1977-01-01

The invention disclosed in this application is directed towards developing a radioiodination method which is applicable to the labeling of 2.02 micrometer (μm) and 0.37 micrometer (μm) diameter polyvinyltoluene latex particles that have been used as an immunoadsorbent. More particularly the overall method includes using an oxidation-reduction chemical reaction for tagging latex particles. Two methods are described. One, the hydrochloric acid method; and two, the nitric acid method

Rapid latex agglutination test for the serodiagnosis of human brucellosis

NARCIS (Netherlands)

Abdoel, Theresia H.; Smits, Henk L.

2007-01-01

We developed and evaluated a user-friendly latex agglutination assay for the serodiagnosis of human brucellosis. The assay was obtained by coating colored latex beads with Brucella lipopolysaccharides and drying of the activated beads onto white agglutination cards. Individual cards were sealed in a

LOL2 and LOL5 loci control latex production by laticifer cells in Euphorbia lathyris.

Science.gov (United States)

Castelblanque, Lourdes; Balaguer, Begoña; Marti, Cristina; Orozco, Marianela; Vera, Pablo

2018-06-07

Laticifers are specialized plant cells capable of indefinite elongation that ramify extensively and are responsible for latex biosynthesis and accumulation. However, the mechanisms underlying laticifer cell differentiation, growth and production of latex remain largely unknown. In a search for mutants showing enhanced accumulation of latex we identified two LOT OF LATEX (LOL) loci in Euphorbia lathyris. lol2 and lol5 mutants show enhanced production of latex contained within laticifer cells. The recessive lol2 mutant carries increased biosynthesis of the plant hormone jasmonoyl-isoleucine (JA-Ile) and therefore establishes a genetic link between jasmonic acid (JA) signaling and latex production in laticifers. Instead, heightened production of latex in lol5 plants obeys to enhanced proliferation of laticifer cells. Phylogenetic analysis of laticifer-expressed genes in E. lathyris and in two other latex-bearing species, Euphorbia corallioides and Euphorbia palustris, allowed the identification of canonical JA responsive elements present in the gene promoter regions of laticifer marker genes. Moreover, we identified that the hormone JA functions not as a morphogen for laticifer differentiation but as a trigger for the fill out of laticifers with latex and the associated triterpenoids. The identification of LOL loci represents a further step towards the understanding of mechanisms controlling latex production in laticifer cells. No claim to original US Government works New Phytologist © 2018 New Phytologist Trust.

Recent (2008-10) concentrations and isotopic compositions of nitrate and concentrations of wastewater compounds in the Barton Springs zone, south-central Texas, and their potential relation to urban development in the contributing zone

Science.gov (United States)

Mahler, Barbara J.; Musgrove, MaryLynn; Herrington, Chris; Sample, Thomas L.

2011-01-01

During 2008–10, the U.S. Geological Survey, in cooperation with the City of Austin, the City of Dripping Springs, the Barton Springs/Edwards Aquifer Conservation District, the Lower Colorado River Authority, Hays County, and Travis County, collected and analyzed water samples from five streams (Barton, Williamson, Slaughter, Bear, and Onion Creeks), two groundwater wells (Marbridge well [YD–58–50–704] and Buda well [LR–58–58–403]), and the main orifice of Barton Springs in Austin, Texas, with the objective of characterizing concentrations and isotopic compositions of nitrate and concentrations of wastewater compounds in the Barton Springs zone. The Barton Springs zone is in south-central Texas, an area undergoing rapid growth in population and in land area affected by development, with associated increases in wastewater generation. Over a period of 17 months, during which the hydrologic conditions transitioned from dry to wet, samples were collected routinely from the streams, wells, and spring and, in response to storms, from the streams and spring; some or all samples were analyzed for nitrate, nitrogen and oxygen isotopes of nitrate, and waste­water compounds. The median nitrate concentrations in routine samples from all sites were higher in samples collected during the wet period than in samples collected during the dry period, with the greatest difference for stream samples (0.05 milligram per liter during the dry period to 0.96 milligram per liter for the wet period). Nitrate concentrations in recent (2008–10) samples were elevated relative to concentrations in historical (1990–2008) samples from streams and from Barton Springs under medium- and high-flow conditions. Recent nitrate concentrations were higher than historical concentrations at the Marbridge well but the reverse was true at the Buda well. The elevated concentrations likely are related to the cessation of dry conditions coupled with increased nitrogen loading in the

Involvement of Ethylene in the Latex Metabolism and Tapping Panel Dryness of Hevea brasiliensis

Science.gov (United States)

Putranto, Riza-Arief; Herlinawati, Eva; Rio, Maryannick; Leclercq, Julie; Piyatrakul, Piyanuch; Gohet, Eric; Sanier, Christine; Oktavia, Fetrina; Pirrello, Julien; Kuswanhadi; Montoro, Pascal

2015-01-01

Ethephon, an ethylene releaser, is used to stimulate latex production in Hevea brasiliensis. Ethylene induces many functions in latex cells including the production of reactive oxygen species (ROS). The accumulation of ROS is responsible for the coagulation of rubber particles in latex cells, resulting in the partial or complete stoppage of latex flow. This study set out to assess biochemical and histological changes as well as changes in gene expression in latex and phloem tissues from trees grown under various harvesting systems. The Tapping Panel Dryness (TPD) susceptibility of Hevea clones was found to be related to some biochemical parameters, such as low sucrose and high inorganic phosphorus contents. A high tapping frequency and ethephon stimulation induced early TPD occurrence in a high latex metabolism clone and late occurrence in a low latex metabolism clone. TPD-affected trees had smaller number of laticifer vessels compared to healthy trees, suggesting a modification of cambial activity. The differential transcript abundance was observed for twenty-seven candidate genes related to TPD occurrence in latex and phloem tissues for ROS-scavenging, ethylene biosynthesis and signalling genes. The predicted function for some Ethylene Response Factor genes suggested that these candidate genes should play an important role in regulating susceptibility to TPD. PMID:26247941

Occurrence of Legionella in wastewater treatment plants linked to wastewater characteristics.

Science.gov (United States)

Caicedo, C; Beutel, S; Scheper, T; Rosenwinkel, K H; Nogueira, R

2016-08-01

In recent years, the occurrence of Legionella in wastewater treatment plants (WWTP) has often been reported. However, until now there is limited knowledge about the factors that promote Legionella's growth in such systems. The aim of this study was to investigate the chemical wastewater parameters that might be correlated to the concentration of Legionella spp. in WWTP receiving industrial effluents. For this purpose, samples were collected at different processes in three WWTP. In 100 % of the samples taken from the activated sludge tanks Legionella spp. were detected at varying concentrations (4.8 to 5.6 log GU/mL) by the quantitative real-time polymerase chain reaction method, but not by the culture method. Statistical analysis with various parameters yielded positive correlations of Legionella spp. concentration with particulate chemical oxygen demand, Kjeldahl nitrogen and protein concentration. Amino acids were quantified in wastewater and activated sludge samples at concentrations that may not support the growth of Legionella, suggesting that in activated sludge tanks this bacterium multiplied in protozoan hosts.

Concentrations of Mercury, Lead, Chromium, Cadmium, Arsenic and Aluminum in Irrigation Water Wells and Wastewaters Used for Agriculture in Mashhad, Northeastern Iran

Directory of Open Access Journals (Sweden)

SR Mousavi

2013-04-01

Full Text Available Background: Contamination of water by toxic chemicals has become commonly recognized as an environmental concern. Based on our clinical observation in Mashhad, northeastern Iran, many people might be at risk of exposure to high concentrations of toxic heavy metals in water. Because wastewater effluents as well as water wells have been commonly used for irrigation over the past decades, there has been some concern on the toxic metal exposure of crops and vegetables irrigated with the contaminated water. Objective: To measure the concentrations of mercury, lead, chromium, cadmium, arsenic and aluminium in irrigation water wells and wastewaters used for agriculture in Mashhad, northeastern Iran. Methods: 36 samples were taken from irrigation water wells and a wastewater refinery in North of Mashhad at four times—May 2008, March 2009, and June and July 2010. Atomic absorption spectrometry was used to measure the concentration of toxic metals. Graphite furnace was used for the measurement of lead, chromium, cadmium and aluminum. Mercury and arsenic concentrations were measured by mercury/hydride system. Results: Chromium, cadmium, lead and arsenic concentrations in the samples were within the standard range. The mean±SD concentration of mercury in irrigation wells (1.02±0.40 μg/L exceeded the FAO maximum permissible levels. The aluminum concentration in irrigation water varied significantly from month to month (p=0.03. All wastewater samples contained high mercury concentrations (6.64±2.53 μg/L. Conclusion: For high mercury and aluminum concentrations, the water sources studied should not be used for agricultural use. Regular monitoring of the level of heavy metals in water and employing the necessary environmental interventions in this area are strongly recommended.

Allergenicity of latex rubber products used in South African dental ...

African Journals Online (AJOL)

Fourteen latex examination gloves (powdered and non-powdered) and five dental rubber dams, representing 6 brands, from five dental academic institutions were analysed for latex allergens and total protein. Total protein content was determined using the BioRad DC protein assay kit and natural rubber allergen levels ...

The rapid determination of volatile fatty acid number in para rubber latex using fourier transform-near infrared spectroscopy based on quantification and discrimination model

Directory of Open Access Journals (Sweden)

Sureeporn Narongwongwattana

2015-09-01

Full Text Available Volatile Fatty Acid number (VFA no. is one of the parameters indicating the state of quality of Para rubber latex at that particular time. Most factories analyze this parameter using standard analytical method as in ISO 506:1992(E. Nevertheless, this procedure is complicated, chemical and time consuming, as well as skilled analyst required. Therefore, near infrared (NIR spectroscopy which is rapid, accurate and nonchemicals method was applied to determine the VFA no. in field latex and concentrated latex based on quantification and discriminant model. The best calibration equation was obtained from standard normal variate (SNV spectra in the region of 6109.7–5770.3, 4613.1–4242.9 cm-1 with R = 0.832, SECV = 0.036 and no bias. From the performance check, statistically it was found that SECV and bias were low enough for practical acceptance and the predicted VFA no. was not different significantly from actual VFA no. at 95% confidence intervals. In addition, discriminant model was developed to separate good quality latex from the deteriorated latex using VFA no. at 0.06 as standard as in ISO 2004:2010(E. The discriminant model can be used to screen the latex with overall accuracy of 91.86% in validation set.

Comparing the level of dexterity offered by latex and nitrile SafeSkin gloves.

Science.gov (United States)

Sawyer, Jo; Bennett, Allan

2006-04-01

An increase in the occurrence of latex allergy has been concurrent with the increasing use of latex gloves by laboratory and healthcare workers. In recent years nitrile gloves have been used to replace latex gloves to prevent latex allergy. Nitrile gloves offer a comparable level of protection against chemical and biological agents and are more puncture resistant. However, if manual dexterity is compromised by nitrile gloves to a greater degree than latex then this may increase the risk of sharps injuries. The Purdue pegboard test, which measures both gross and fine finger dexterity, was used to test the dexterity levels of two glove types used at HPA CEPR; Kimberly-Clark SafeSkin nitrile and latex laboratory gloves. There was a statistically significant 8.6% increase in fine finger dexterity provided by latex compared with nitrile SafeSkin laboratory gloves but no difference in gross dexterity between the glove types. There was no significant relationship between glove dexterity and age or gender. The selection of glove size was influenced by the digit length of participants. Moreover, those with longer, thinner fingers appeared to have an advantage when using nitrile SafeSkin gloves. The level of dexterity provided by latex and nitrile SafeSkin gloves for tasks on a gross dexterity level are comparable and health workers will benefit from the non-allergenic properties of nitrile. For tasks requiring fine finger dexterity nitrile SafeSkin gloves may impede dexterity. Despite this, the degree of restriction appears to have a negligible impact on safety in this study when compared with the risk of latex sensitization and subsequent allergy. In addition to glove material, working practices must also take into account glove size, fit, grip and thickness, as these factors can all influence dexterity.

Natural rubber latex: determination and interpretation of flow curves

Directory of Open Access Journals (Sweden)

Harrison Lourenço Corrêa

2015-08-01

Full Text Available AbstractAs consumers become more demanding, the importance grows of guaranteeing the quality of products. The employment of reliable testing techniques that assure the origin and characteristics of the inputs used by industry is a key factor in this respect. In the rubber processing industry, the most commonly used characterization tests include determination of the total solids and dry rubber content, mechanical stability, odor, color and presence of volatile compounds, among others. For the most part, these tests are sufficient for the latex transformation industry. However, in situations where there is a need to know the behavior of latex in reaction to the mechanical forces of machines (mixers, pumps, etc., other tests must be used. Rheological tests to determine viscoelastic data by means of plotting flow curves combined with the application of theoretical models can provide important details for characterization of different types of latex. This article presents the protocol employed by the Rheology and Image Laboratory of Rio de Janeiro State University (UERJ for the rheological study of Brazilian latex. The samples analyzed came from the state of São Paulo.

Latex glove sensitivity amongst diagnostic imaging healthcare personnel: a self-reporting investigation

International Nuclear Information System (INIS)

Healy, Jan; Brennan, Patrick C.; Bowden, Julie Anne

2003-01-01

The use of latex gloves has risen dramatically among healthcare workers resulting in an increase in the number of workers experiencing reactions to gloves. Little evidence of reactions among Irish healthcare workers is available. The current, self-reporting study investigated the prevalence to latex gloves amongst four professional groups within three Diagnostic Imaging Departments. Prevalence is similar to that demonstrated elsewhere with 18.3% of individuals expressing latex associated symptoms. Symptoms included itching and redness of hands, dry cracked skin, soreness of eyes and upper respiratory tract complaints. These results indicate that latex hypersensitivity is a real problem amongst Irish healthcare workers. This preliminary work provides the basis of a much larger controlled study currently being planned

Latex-modified fiber-reinforced concrete bridge deck overlay : construction/interim report.

Science.gov (United States)

1993-06-01

Latex-modified concrete (LMC) is Portland cement concrete (PCC) with an admixture of latex. LMC is considered to be nearly impermeable to chlorides and is extensively used to construct bridge deck overlays. Unfortunately, some of these overlays have ...

Identification and characterization of Euphorbia nivulia latex proteins.

Science.gov (United States)

Badgujar, Shamkant B; Mahajan, Raghunath T

2014-03-01

The protein profile of latex of Euphorbia nivulia Buch.-Ham. is established. Three new proteins viz., Nivulian-I, II and III have been purified to homogeneity from the latex. The relative molecular masses of Nivulian-I, II and III are 31,486.985, 43,670.846 and 52,803.470 Da respectively. Nivulian-I is a simple type of protein while Nivulian-II and III are glycoproteins. Peptide mass fingerprint analysis revealed peptides of these proteins match with Tubulin alpha-1 chain of Eleusine indica, Maturase K of Banksia quercifolia and hypothetical protein of Zea mays respectively. Tryptic digestion profile of Nivulian-I, II and III, infer the exclusive nature of latex origin proteins and may be new and are additive molecules in the dictionaries of phytoproteins or botany. This is the first of its kind, regarding characterization and validation of Nivulian-I, II and III with respect to peptide sequencing. Copyright © 2013 Elsevier B.V. All rights reserved.

Antimalarial Anthrone and Chromone from the Leaf Latex of Aloe ...

African Journals Online (AJOL)

In Ethiopian traditional medicine, the leaf latex of Aloe debranan Chrstian is used for the treatment of several diseases including malaria. In an ongoing search for effective, safe and cheap antimalarial agents from plants, the leaf latex of A. debrana was tested for its in vivo antimalarial activity, in a 4-day suppressive assay ...

Polylactide/Montmorillonite Hybrid Latex as a Barrier Coating for Paper Applications

Directory of Open Access Journals (Sweden)

Davide Bandera

2016-03-01

Full Text Available We developed a paper coating for the potential application in food packaging based on polylactide and montmorillonite. It is applied to the paper in the form of a stable, water-based latex with a solid content of 25–28 wt %. The latex is prepared from a commercially available polylactide, surfactants, montmorillonite, a plasticizer, chloroform (to be removed later and water by an emulsion/solvent evaporation procedure. This coating formulation is applied to the paper substrate by bar-coating, followed by hot-pressing at 150 °C. The coated papers achieved up to an 85% improvement in water vapor transmission rates when compared to the pristine papers. The coating latex is prepared from inexpensive materials and can be used for a solvent-free coating process. In addition, the ingredients of the latex are non-toxic; thus, the coated papers can be safely used for food packaging.

Physical-biopolymer characterization of polyhydroxybutyrate-co-hydroxyvalerate (PHBV) blended with natural rubber latex

Energy Technology Data Exchange (ETDEWEB)

Kuntanoo, K., E-mail: thip-kk@hotmail.com [Graduate School of Khon Kaen University, Khon Kaen, 40002 Thailand (Thailand); Promkotra, S., E-mail: sarunya@kku.ac.th [Department of Geotechnology, Faculty of Technology, Khon Kaen University, Khon Kaen 40002 Thailand (Thailand); Kaewkannetra, P., E-mail: paknar@kku.ac.th [Department of Biotechnology, Faculty of Technology, Khon Kaen University, Khon Kaen 40002 Thailand (Thailand)

2015-03-30

A biopolymer of polyhydroxybutyrate-co-hydroxyvalerate (PHBV) is blended with bio-based materials, natural rubber latex, to improve their microstructures. The various ratios between PHBV and natural rubber latex are examined to develop their mechanical properties. In general, physical properties of PHBV are hard, brittle and low flexible while natural rubber (NR) is presented itself as high elastic materials. Concentrations of the PHBV solution are constituted at 1%, 2% and 3% (w/v). The mixtures of their PHBV solutions to natural rubber latex are produced the blended films in three different ratios of 4:6, 5:5 and 6:4, respectively. They are characterized by appearance analyses which are the scanning electron microscope (SEM), universal testing machine (UTM) and differential scanning calorimetry (DSC). The SEM photomicrographs of the blended films and the controlled PHBV can provide the void distribution in the range of 12-14% and 19-21%, respectively. For mechanical properties of the blended films, the various elastic moduli of 1%, 2% and 3% (w/v) PHBV are the average of 773, 956 and 1,007 kPa, respectively. The tensile strengths of the blends increase with the increased concentrations of PHBV, similarly trend to the elastic modulus. The crystallization and melting behavior of unmixed PHBV and the blends are determined by DSC. Melting transition temperatures (T{sub m}) of the unmixed PHBV are stated two melting peak at 154°C and 173°C. Besides, the melting peaks of the blends alter in the range of 152-156°C and 168-171°C, respectively. According to morphology of the blends, the void distribution decreases twice compared to the unmixed PHBV. The results of mechanical properties and thermal analysis indicate that the blended PHBV can be developed their properties by more resilient and wide range of temperature than usual.

Study of Antibacterial Activity and Bacteriology of Latex from Asclepias syriaca L

Science.gov (United States)

McCay, Steven; Mahlberg, Paul

1973-01-01

Whole and fractionated latex of Asclepias syriaca was tested for antimicrobial or growth-promoting activity with 16 genera and species of bacteria. Latex and extracted fractions (distilled water, acetic acid, sodium bicarbonate, sulfuric acid, and ethyl ether) possessed no detectable antimicrobial activity. Comparison of growth curves of selected bacteria incubated with serum and rubber fractions, as well as controls, revealed no detectable inhibition of growth, except for a slight inhibitory response to autoclaved serum. Most bacteria were capable of utilizing latex for a substrate as indicated by the increased growth rate in the exponential phase. The stationary phase was entered simultaneously by both the treated cultures and the controls. Various bacteria cultured in a litmus latex mixture yielded populations which ranged from <104 organisms/ml for Lactobacillus casei, Staphylococcus aureus and Micrococcus lysodeikticus to 1.1 × 1010 organisms/ml for Clostridium acetobutylicum. Whole latex, as well as the serum and rubber fractions, support the growth of various bacteria, but under field conditions there is no evidence for systemic infection of this type of cell by bacteria. PMID:4790590

Application of radiation vulcanized natural rubber latex in Indonesia

International Nuclear Information System (INIS)

Soebianto, Y.S.; Wiwik Sofiarti; Razzak, M.T.

1996-01-01

The center has carried out R and D of Radiation Vulcanization Natural Rubber Latex (RVNRL) technology and introduced it to the industries since the inauguration and operation of the latex pilot plant in 1983. After years of experiences and the environmental consideration, n-butylacrylate (n-BA) has replaced CCI, as the sensitizer. Until now the introduction program shows that radiation vulcanized latex is more suitable for home industries than large industries. The obstacle of the program is the marketing of the dipped products. In spite of these problems, the introduction of this technology to the people in some undeveloped area of Java has supported the national program to improve their living standard. The problems of nitrosamine and protein allergic have turn up RVNRL to be the substitute of sulfur vulcanized latex in the future. The cooperation with a national condom manufacturer (PT Mitra Banjaran) has applied RVNRL for condom production in the large scale. Soft condoms with less probability of pinhole are obtained, but the technical problem is stickiness after pilling. Supply to a baby teat and a rubber thread manufacturer offers great advantages by not using any chemicals. In spite of the advantages, the problem of latex viscosity for dipping and the low modulus of elasticity of the threads arise. Through those input CAIR-BATAN is conducting the research and development in improving the crosslinking among the rubber particles that are supposed to be the reason of the stickiness and low modulus of elasticity. This effort is expected to be able to broaden the application of RVNRL, and it will be achieved only by the involvement of rubber chemist, rubber technologist, and radiation chemist

Histamine mediates the pro-inflammatory effect of latex of Calotropis procera in rats

Directory of Open Access Journals (Sweden)

Yatin M. Shivkar

2003-01-01

Full Text Available Introduction: Calotropis procera is known to produce contact dermatitis and the latex of this plant produces intense inflammation when injected locally. However, the precise mode of its pro-inflammatory effect is not known. In present study we have pharmacologically characterized the inflammation induced by latex of C. procera in a rat paw edema model and determined the role of histamine in latex-induced inflammation.

Pilot scale experiments on radiation vulcanization of NR latex

International Nuclear Information System (INIS)

Ridwan, M.

1985-01-01

The potential of irradiated latex as raw material of commercial use is under testing on pilot plant scale in Indonesia which has 225 kCi Co-60 irradiation facility and can irradiate 1000 tonnes of centrifuged latex per annum. The facility was jointly designed by BATAN of Indonesia and JAERI of Japan and was jointly financed by UNDP/IAEA, Government of Japan and Government of Indonesia under UNDP/IAEA Regional Cooperative Agreement Project on Industrial Application of Isotopes and Radiation Technology. The facility is a water pool type and can accommodate 400 kCi Co-60. The Co-60 rack has two shapes, plate and cylindrical shapes. The plate shape source is used for natural rubber latex irradiation and the cylindrical one is used for other irradiation services. The vulcanization system consists of three major components: emulsification unit, mixing unit and vulcanization reactor. The first two components are located outside shielded room while the third one in irradiation room. The radiation vulcanization process is a much simpler energy saving process compared to the conventional thermal process which has two vulcanization steps before and after dipping. The physical and mechanical properties of irradiated NR latex are comparable to those of sulfur vulcanized. (author)

THE IMPACT OF FOOD WASTE DISCHARGE INTO THE MUNICIPAL SEWERAGE ON COD CONCENTRATION IN URBAN WASTEWATER IN OLSZTYN

Directory of Open Access Journals (Sweden)

Wojciech Janczukowicz

2016-05-01

Full Text Available The operators of wastewater treatment plants in Poland have been observing an increase in the concentration of raw sewage for several years. In particular for organic substances. This is the effect of water consumption reduction, restoration of the sewerage networks, growing wealth, widespread waste of food. The most serious adverse, influencing on the municipal wastewater composition is colloid mills application in gastronomical objects and the discharge of shredded food waste to sewer. That widespread behavior has been noticed and negated, in 2010 year, by the common position of GIS and the ME. Far too late, which confirms the situation observed at the Olsztyn wastewater treatment plant, where the biggest increase of COD values ​​was observed in 2008–2010. The average concentration of COD of sewage in the period 2011–2014 was almost twice higher than in 1996, real PE is close to the design value, despite the fact that the hydraulic load of the object slightly exceeded 50% of design value. Removing such large organic pollutant loads generates high costs, that could be avoided by reasonable food waste management.

Study on irradiation condition in radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Zhu Nankang; Wang Chunlei; Makuuchi, K.; Yoshii, F.

1996-01-01

The effect of gamma rays irradiation dose rates on RVNRL preparation was studied using Malaysian latex added with O.2 phr of KOH and 5 phr n-BA. The results showed, to ensure the tensile strength of the latex film meet the requirement, when applying vulcanisation doses, Dv of 20 kGy 20 and 15 kGy, irradiation dose rates should not be greater than 0. 49 kGy/hr and 1. 6 kGy/hr respectively. Its was found that within the storage time of 20 days there was no change in the physical properties of the latex films

Effect of adding low-concentration of rhamnolipid on reactor performances and microbial community evolution in MBBRs for low C/N ratio and antibiotic wastewater treatment.

Science.gov (United States)

Peng, Pengcheng; Huang, Hui; Ren, Hongqiang

2018-05-01

This study aims to explore the potential of low-concentration of rhamnolipid in efficient treatment of wastewater with poor biodegradability. Six lab-scale moving bed biofilm reactors (MBBRs) were applied to investigate the effect of rhamnolipid concentration (0, 20, 50 mg/L) on pollutants removal, biomass accumulation, microbial morphology and community evolution in synthetic low C/N ratio (3:1) and antibiotic (50 μg/L tetracycline) wastewater. 20 mg/L rhamnolipid treated groups exhibited significant increase (p poorly biodegradable wastewater by biofilm process with moderate amount of rhamnolipid. Copyright © 2018 Elsevier Ltd. All rights reserved.

Respiratory and dermal symptoms in Thai nurses using latex products.

Science.gov (United States)

Supapvanich, C; Povey, A C; de Vocht, F

2013-09-01

Despite known health risks related to the use of powdered latex gloves (PLGs), they are still widely used in hospitals in developing countries due to the high cost of alternatives. To determine the prevalence of dermal and respiratory symptoms associated with latex glove use in nurses in Thailand and evaluate the influence of previously reported occupational risk factors in this population. A cross-sectional study in female nurses working in three Thai hospitals. Participants completed a questionnaire on demographics, occupational and personal history, use of latex products at work and dermal and respiratory symptoms attributed to occupational use of latex gloves. Of 899 nurses, 18% reported health effects attributed to the use of latex products. After adjustment for confounding, occupational risk factors associated with increased reporting of dermal symptoms included wearing more than 15 pairs of PLG per day (odds ratio (OR): 2.10, 95% confidence interval (CI): [1.32-3.34]), using chlorhexidine (OR: 2.07, 95% CI: [1.22-3.52]) and being an operating theatre nurse (OR: 2.46, 95% CI: [1.47-4.12]). Being a labour ward nurse (OR: 3.52, 95% CI: [1.26-9.85]) was the only factor associated with increased reporting of respiratory symptoms. Continuing use of PLGs in Thai nurses is associated with increased prevalence of dermal symptoms compared with data from developed countries. Measures to reduce such health effects are well established and should be considered. Additionally, replacement of chlorhexidine with an alternative detergent seems advisable.

Managing latex allergies at home

Science.gov (United States)

... Associate Clinical Professor of Medicine, Division of Allergy, Immunology, and Rheumatology, Georgetown University Medical School, Washington, DC. Also reviewed by David Zieve, MD, MHA, Isla Ogilvie, PhD, and the A.D.A.M. Related MedlinePlus Health Topics Latex Allergy Browse the Encyclopedia A.D.A. ...

Effect of heterogeneous distribution of crosslink density on physical properties of radiation vulcanized NR (Natural Rubber) latex film

International Nuclear Information System (INIS)

Keizo Makuuchi; Fumio Yoshii; Miura, H.; Murakami, K.

1996-01-01

Thus a study has been carried out to investigate the effect of particle to particle variation in crosslink density on physical properties of radiation vulcanized NR latex film. NR latex was irradiated in small bottle by γ rays without vulcanization accelerator to provide latex rubber particles having homogeneous distribution of crosslink density. The doses were 30, 50, 100, 250, 300, 400, 500 and 600 kGy. Weight swelling ratio, gel fraction, tensile strength and elongation at break of the latex film from the mixed latex were measured. The vulcanization dose of this latex was 250 kGy. Then the two different latexes were mixed in a such way to adjust the average dose of 250 kGy to prepare a latex consisting of rubber particles having heterogeneous distribution of crosslink density. Tensile strength of the latex film was depressed by mixing. The reduction increased with increasing the decrease of gel fraction by mixing. However the reduction was not serious when the dose difference of two latexes was less than 200 kGy

Effect of Cambi Thermal Hydrolysis Process-Anaerobic digestion treatment on concentrations on phthalate plasticisers in wastewater sludge

Science.gov (United States)

The impact of the recently implemented Cambi Thermal Hydrolysis Process™-Anaerobic Digestion (TH-AD) solids treatment method on concentrations of 4 phthalate plasticisers in wastewater sludge samples was explored in this study. Samples were analysed for diisononyl phthalate (DiNP), diisodecyl phthal...

Sustainable treatment of rubber latex processing wastewater : the UASB-system combined with aerobic post-treatment

NARCIS (Netherlands)

Viet Nguyen Trung,

1999-01-01

The main objective of this PhD-thesis is to assess the applicability of UASB-process for treating RLP wastewater and the feasibility of some adequate post-treatment processes for the effluent of the anaerobic treatment process.

The studies were carried out in The Netherlands during

Investigation of Sulfate concentration influence on Anaerobic Lagoon performance: Birjand Wastewater Treatment plant: A Case study

Directory of Open Access Journals (Sweden)

Mohammad Malakootian

2016-05-01

Full Text Available Background and Aim: In the present study the influence of the different sulfate concentration on the anaerobic lagoon stabilization was investigated. Materials and Methods: The present study is an experimental research carried out on anaerobic stabilization pond pilot for 7 months in Birjand wastewater treatment plant. After making sure of a steady state sulfate with different concentrations of 200, 300 and 400 mg/L were injected into the pilot. Then parameters including pH, organic nitrogen, ammonia nitrogen, BOD5, COD and nitrate were measured. All of the experiments were carried out according to the methods presented in the book "Standard Method" for the examination of water and wastewater (2005. Results: It was found that by increasing sulfate concentration from 200 to 300 mg/L all of parameters  except BOD5 (10% reduction had no significant changes., but by increasing the sulfate concentration from 200 to 400 mg/L the removal efficiency of the parameters such as BOD5, COD, Organic nitrogen, total kjeldahl nitrogen, nitrate and sulfate reduced to 11, 8, 12, 26, 6 and 10 percent, respectively. PH in the first stage was alkaline and then changed to acidic. Conclusion: Anaerobic stabilization ponds have different capacities for removal of organic compounds at different sulfate concentrations; so that; in sulfate concentration of 200 mg/L, the proper operation was seen and in concentration of 300 mg/L, sulfate-reducing bacteria get dominant and therefore odor is produced..  Alternatively, by increasing the concentration of sulphate to 400 mg/L, ammonia nitrogen increased 2.5 times (150% in the effluent.

Synthesis and Characterization of Core-Shell Acrylate Based Latex and Study of Its Reactive Blends

Directory of Open Access Journals (Sweden)

Ying Nie

2008-03-01

Full Text Available Techniques in resin blending are simple and efficient method for improving the properties of polymers, and have been used widely in polymer modification field. However, polymer latex blends such as the combination of latexes, especially the latexes with water-soluble polymers, were rarely reported. Here, we report a core-shell composite latex synthesized using methyl methacrylate (MMA, butyl acrylate (BA, 2-ethylhexyl acrylate (EHA and glycidyl methacrylate (GMA as monomers and ammonium persulfate and sodium bisulfite redox system as the initiator. Two stages seeded semi-continuous emulsion polymerization were employed for constructing a core-shell structure with P(MMA-co-BA component as the core and P(EHA-co-GMA component as the shell. Results of Transmission Electron Microscopy (TEM and Dynamics Light Scattering (DLS tests confirmed that the particles obtained are indeed possessing a desired core-shell structural character. Stable reactive latex blends were prepared by adding the latex with waterborne melamine-formaldehyde resin (MF or urea-formaldehyde resin (UF. It was found that the glass transition temperature, the mechanical strength and the hygroscopic property of films cast from the latex blends present marked enhancements under higher thermal treatment temperature. It was revealed that the physical properties of chemically reactive latexes with core-shell structure could be altered via the change of crosslinking density both from the addition of crosslinkers and the thermal treatment.

Progress in radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Makuuchi, Keizo

2000-01-01

Vulcanization dose defined as the radiation dose at which cross-linked natural rubber in latex has the maximum tensile strength can be reduced by adding carbon tetrachloride as a reaction accelerator. The radiation vulcanization of natural rubber latex was selected as one of regional projects of IAEA in 1989 and a pilot plant was built in Jakarta. The products from it were evaluated during 1983-1985, followed by IAEA decision to support the continued R and D study at Takasaki, JAERI. Various factors to improve the properties of the products have been studied. Several advantages of the process over conventional method, such as absence of N-nitrosoamines, low cytotoxicity, decomposability in the environment, transparency and softness, were confirmed. The technology has been transferred toward commercial application in Thailand, and pilot plants being set up in Indonesia, India, Malaysia and Thailand. Moreover, the process was found to be effective in reducing protein remaining in natural rubber latex products and the initial investment and irradiation cost was found to be greatly reduced by employing low energy electron accelerator. This paper reviews such progress. (S. Ohno)

Extractable protein of radiation vulcanized natural rubber latex

International Nuclear Information System (INIS)

Soebianto, Y.S.; Ratnayake, U.M.; Makuuchi, Keizo; Yoshii, Fumio; Kume, Tamikazu

2000-01-01

Protein remained in the latex products are reported to cause serious allergy. A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) in three different processes. The amount of WSP was 3 phr. It was only added to RVNRL (standard), added to re-centrifuged RVNRL (pre-centrifugation), and added to RVNRL followed by centrifugation (post-centrifugation). The protein content was determined by enhanced BCA method, and identified by SDS-PAGE. Extractable protein (EP) from the rubber has been reduced up to the minimum protein detection by combining WSP addition and centrifugation. Short leaching time (20-30 min.) can be achieved after the combine treatment, and SDS-PAGE confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The efficiency of protein removal by WSP depends on its molecular weight of WSP which relates to its water solubility. (author)

Treatment of wastewaters from manufactured gas plants

Energy Technology Data Exchange (ETDEWEB)

Cocheci, V.; Bogatu, C.; Radovan, C. [Technical University of Timisoara, Timisoara (Romania)

1995-12-31

The treatment of wastewaters with high concentrations of organic compounds often represents a difficult problem. In some cases, for the destruction and removal of toxic compounds using processes like biological and chemical oxidation were proposed. Wastewaters from manufactured gas plants contain high concentrations of organic pollutants and ammonia. In this paper a technology for the treatment of these wastewaters is proposed. The experiments were realized with wastewaters from two Romanian manufactured gas plants. The process consists of the following steps: polycondensation-settling-stripping-biological treatment-electrocoagulation-electrochemical oxidation, or chemical oxidation. 6 refs., 4 tabs.

Identification of some factors affecting pharmaceutical active compounds (PhACs) removal in real wastewater. Case study of fungal treatment of reverse osmosis concentrate.

Science.gov (United States)

Badia-Fabregat, Marina; Lucas, Daniel; Gros, Meritxell; Rodríguez-Mozaz, Sara; Barceló, Damià; Caminal, Glòria; Vicent, Teresa

2015-01-01

Many technologies are being developed for the efficient removal of micropollutants from wastewater and, among them, fungal degradation is one of the possible alternative biological treatments. In this article, some factors that might affect pharmaceutically active compounds (PhACs) removal in a fungal treatment of real wastewater were identified in batch bioreactor treating reverse osmosis concentrate (ROC) from urban wastewater treatment plant (WWTP). We found that degradation of PhACs by Trametes versicolor was enhanced by addition of external nutrients (global removal of 44%). Moreover, our results point out that high aeration might be involved in the increase in the concentration of some PhACs. In fact, conjugation and deconjugation processes (among others) affect the removal assessment of emerging contaminants when working with real concentrations in comparison to experiments with spiked samples. Moreover, factors that could affect the quantification of micropollutants at lab-scale experiments were studied. Copyright © 2014 Elsevier B.V. All rights reserved.

Improving of Water Resistance of Asphalt Concrete Wearing Course Using Latex-Bitumen Binder

Directory of Open Access Journals (Sweden)

Siswanto Henri

2017-01-01

Full Text Available It is well known that presence of water in a bituminous mix is a critical factor which can lead to premature failure of flexible pavements. This requires solutions one of which is to formulate an asphalt mix that has a high resistance to moisture and one way to do this is to mix latex with the asphalt mix. The purpose of this experimental study was to investigate the effect of water on Marshall stability of asphalt concrete wearing course (ACWC made with a latex-bitumen binder. Latex-bitumen was mixed with aggregate and four levels of latex content were investigated in this study, namely, 0%, 2%, 4% and 6% respectively by weight of asphalt. Wet procces was used in the blending of mixtures. The procedure used to obtain the optimum binder contents conformed to the Marshall procedure (SNI 06-2489-1991. Six Marshall specimens at optimum binder content were prepared for each binder mix investigated. Three of six specimens from each group were tested under Marshall standards. The remaining specimens were tested by immersion in a bath at 60°C for 24 hours. The Marshall index of retained stability was used to evaluate the effect of water on the Marshall stability of ACWC. The results indicated that the addition of up to 4% latex to ACWC mix increased the retained Marshall stability, whereas the addition of latex above 4% decreased the retained stability of the mixture. The addition of 4% CRM significantly improved the retained stability of the mixture and was the best latex – ACWC mix.

IMMEDIATE AND DELAYED HYPERSENSITIVITY REACTIONS TO LATEX GLOVES IN A DENTAL STUDENT. A case report.

Directory of Open Access Journals (Sweden)

Iliyana Stoeva

2011-08-01

Full Text Available The article presents a case of dental student with immediate and delayed hypersensitivity reaction to latex gloves. Symptoms appeared during the second year of regularly using of latex gloves. The student was with no history of allergies and no previous exposure to latex products.

Preparation of novel film-forming armoured latexes using silica nanoparticles as a pickering emulsion stabiliser.

Science.gov (United States)

Shiraz, Hana; Peake, Simon J; Davey, Tim; Cameron, Neil R; Tabor, Rico F

2018-05-15

Film-forming polymer latex particles of diameter acrylate (BA) as co-monomers, potassium persulphate (KPS) as an initiator and a commercially available colloidal nano-silica (Ludox®-TM40). It was found that pH control before polymerisation using methacrylic acid (MAA) facilitated the formation of armoured latexes, and mechanistic features of this process are discussed. An alternative, more robust protocol was developed whereby addition of vinyltriethoxysilane (VTES) to control wettability resulted in latexes completely armoured in colloidal nano-silica. The latexes were characterised using SEM, cryo-TEM and AFM imaging techniques. The mechanism behind the adsorption was investigated through surface pressure and contact angle measurements to understand the factors that influence this irreversible adsorption. Results indicate that nanoparticle attachment (but intriguingly not latex size) is dependent on particle wettability, providing new insight into the formation of nanoparticle-armoured latexes, along with opportunities for further development of diversely functionalized inorganic/organic polymer composite particles. Copyright © 2018 Elsevier Inc. All rights reserved.

Occurrence of bisphenol A in wastewater and wastewater sludge of CUQ treatment plant

Directory of Open Access Journals (Sweden)

Dipti Prakash Mohapatra

2011-09-01

Full Text Available The identification and quantification of bisphenol A (BPA in wastewater (WW and wastewater sludge (WWS is of major interest to assess the endocrine activity of treated effluent discharged into the environment. BPA is manufactured in high quantities fro its use in adhesives, powder paints, thermal paper and paper coatings among others. Due to the daily use of these products, high concentration of BPA was observed in WW and WWS. BPA was measured in samples from Urban Community of Quebec wastewater treatment plant located in Quebec (Canada using LC-MS/MS method. The results showed that BPA was present in significant quantities (0.07 μg L–1 to 1.68 μg L–1 in wastewater and 0.104 μg g–1 to 0.312 μg g–1 in wastewater sludge in the wastewater treatment plant (WWTP. The treatment plant is efficient (76 % in removal of pollutant from process stream, however, environmentally significant concentrations of 0.41 μg L–1 were still present in the treated effluent. Rheological study established the partitioning of BPA within the treatment plant. This serves as the base to judge the portion of the process stream requiring more treatment for degradation of BPA and also in selection of different treatment methods. Higher BPA concentration was observed in primary and secondary sludge solids (0.36 and 0.24 μg g–1, respectively as compared to their liquid counterpart (0.27 and 0.15 μg L–1, respectively separated by centrifugation. Thus, BPA was present in significant concentrations in the WWTP and mostly partitioned in the solid fraction of sludge (Partition coefficient (Kd for primary, secondary and mixed sludge was 0.013, 0.015 and 0.012, respectively.

Science and technology of rubber reclamation with special attention to NR based waste latex products

NARCIS (Netherlands)

Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

2006-01-01

A comprehensive overview of reclamation of cured rubber with special emphasis on latex reclamation is depicted in this paper. The latex industry has expanded over the years to meet the world demands for gloves, condoms, latex thread, etc. Due to the strict specifications for the products and the

Preliminary study of semi-refined carrageenan (SRC) as secondary gelling agent in natural rubber (NR) latex foam

Science.gov (United States)

Norhazariah, S.; Azura, A. R.; Azahari, B.; Sivakumar, R.

2017-12-01

Semi-refined carrageenan (SRC) product is considerably cheaper and easier to produce as a natural polysaccharide, which was utilized in food and other product application. However, the application in latex is limited. The aim of this work is to evaluate the SRC produced from low industrial grade seaweed (LIGS) in the latex foam application. The FTIR spectra showed the SRC produced as kappa type carrageenan with lower sulfur content compared to native LIGS. NR latex foam is produced by using the Dunlop method with some modifications. The effect of SRC loading as a secondary gelling agent in NR latex foam is investigated. The density and morphology of the NR latex foam with the addition of the SRC are analyzed. NR latex foam density increased with SRC loading and peaked at 1.8 phr SRC. The addition of SRC has induced the bigger cell size compared to the cell size of the control NR latex foam, as shown in the optical micrograph. It can be concluded that SRC LIGS could be acted as secondary gelling agent in NR latex foam.

Radiation vulcanization of natural rubber latex (NRL) using low energy electron beam accelerator

International Nuclear Information System (INIS)

Feroza Akhtar; Keizo Makuuchi; Fumio Yoshii

1996-01-01

The electron beam induced vulcanization of natural rubber latex has been studied using low energy Electron Beam (EB) accelerators of 300, 250 and 175 keV ne latex was irradiated in a special type stainless steel reaction reactor with a stirrer at the bottom of the reactor. From the results it was found that 300 and 250 keV accelerators could effectively vulcanize NRL. But accelerator of 175 keV is too low energy to vulcanize the latex. At the same time a drum type irradiator where thin layer of NRL was irradiated by accelerator, was used for vulcanization of NRL. This type of irradiator also showed good physical properties of vulcanized latex. The effects of beam current and stirrer speed on vulcanization were studied

Concentration, composition, bioavailability, and N-nitrosodimethylamine formation potential of particulate and dissolved organic nitrogen in wastewater effluents: A comparative study

International Nuclear Information System (INIS)

Hu, Haidong; Ma, Haijun; Ding, Lili; Geng, Jinju; Xu, Ke; Huang, Hui; Zhang, Yingying; Ren, Hongqiang

2016-01-01

Wastewater-derived organic nitrogen (org-N) can act as both nutrients and carcinogenic nitrogenous disinfection byproduct precursors. In this study, the concentration, composition, bioavailability, and N-nitrosodimethylamine (NDMA) formation potential of particulate organic nitrogen (PON) from three different municipal wastewater treatment plants were characterized and compared with that of effluent dissolved organic nitrogen (DON). The average effluent PON and DON concentrations ranged from 0.09 to 0.55 mg N/L and from 0.91 to 1.88 mg N/L, respectively. According to principal component analysis, org-N composition and characterization differed in PON and DON samples (n = 20). Compared with DON, PON tended to be enriched in protein and nucleic acids, and showed a more proteinaceous character. Composition of org-N functional groups estimated from the X-ray photoelectron spectroscopy N 1s spectra indicate no significant differences in the molecular weight distribution of the protein-like materials between PON and DON. Moreover, PON exhibited a significantly higher bioavailability (61.0 ± 13.3%) compared to DON (38.5 ± 12.4%, p < 0.05, t-test) and a significantly higher NDMA yields (791.4 ± 404.0 ng/mg-N) compared to DON (374.8 ± 62.5 ng/mg-N, p < 0.05, t-test). Accordingly, PON contributed to approximately 12.3–41.7% of the total bioavailable org-N and 22.0–38.4% of the total NDMA precursors in wastewater effluents. Thus, the potential adverse effects of PON on wastewater discharge and reuse applications should not be overlooked, even though it only accounted for 7.4–26.8% of the total effluent org-N. - Highlights: • The concentration, composition, bioavailability, and NDMA FP of PON and DON in wastewater effluents are compared. • PON is enriched in protein and nucleic acids. • PON is more bioavailable and shows higher NDMA yields compared to DON. • PON contributes12–42% of total bioavailable org-N and 22–38% of total NDMA precursors. �

Concentration, composition, bioavailability, and N-nitrosodimethylamine formation potential of particulate and dissolved organic nitrogen in wastewater effluents: A comparative study

Energy Technology Data Exchange (ETDEWEB)

Hu, Haidong; Ma, Haijun; Ding, Lili; Geng, Jinju; Xu, Ke; Huang, Hui; Zhang, Yingying; Ren, Hongqiang, E-mail: hqren@nju.edu.cn

2016-11-01

Wastewater-derived organic nitrogen (org-N) can act as both nutrients and carcinogenic nitrogenous disinfection byproduct precursors. In this study, the concentration, composition, bioavailability, and N-nitrosodimethylamine (NDMA) formation potential of particulate organic nitrogen (PON) from three different municipal wastewater treatment plants were characterized and compared with that of effluent dissolved organic nitrogen (DON). The average effluent PON and DON concentrations ranged from 0.09 to 0.55 mg N/L and from 0.91 to 1.88 mg N/L, respectively. According to principal component analysis, org-N composition and characterization differed in PON and DON samples (n = 20). Compared with DON, PON tended to be enriched in protein and nucleic acids, and showed a more proteinaceous character. Composition of org-N functional groups estimated from the X-ray photoelectron spectroscopy N 1s spectra indicate no significant differences in the molecular weight distribution of the protein-like materials between PON and DON. Moreover, PON exhibited a significantly higher bioavailability (61.0 ± 13.3%) compared to DON (38.5 ± 12.4%, p < 0.05, t-test) and a significantly higher NDMA yields (791.4 ± 404.0 ng/mg-N) compared to DON (374.8 ± 62.5 ng/mg-N, p < 0.05, t-test). Accordingly, PON contributed to approximately 12.3–41.7% of the total bioavailable org-N and 22.0–38.4% of the total NDMA precursors in wastewater effluents. Thus, the potential adverse effects of PON on wastewater discharge and reuse applications should not be overlooked, even though it only accounted for 7.4–26.8% of the total effluent org-N. - Highlights: • The concentration, composition, bioavailability, and NDMA FP of PON and DON in wastewater effluents are compared. • PON is enriched in protein and nucleic acids. • PON is more bioavailable and shows higher NDMA yields compared to DON. • PON contributes12–42% of total bioavailable org-N and 22–38% of total NDMA precursors. �

Treatment of highly concentrated tannery wastewater using electrocoagulation: Influence of the quality of aluminium used for the electrode

International Nuclear Information System (INIS)

Elabbas, S.; Ouazzani, N.; Mandi, L.; Berrekhis, F.; Perdicakis, M.; Pontvianne, S.; Pons, M-N.; Lapicque, F.; Leclerc, J-P

2016-01-01

Highlights: • COD and Cr(III) species can be simultaneously removed by electrocoagulation. • Cu-containing Al alloy is more efficient than pure Al as electrodes. • Dilution of too concentrated tannery wastewater is required for efficient treatment. - Abstract: This paper deals with the ability of electrocoagulation (EC) to remove simultaneously COD and chromium from a real chrome tanning wastewater in a batch stirred electro-coagulation cell provided with two aluminium-based electrodes (aluminium/copper/magnesium alloy and pure aluminium). Effects of operating time, current density and initial concentration of Cr(III) and COD have been investigated. The concentrations of pollutants have been successfully reduced to environmentally acceptable levels even if the concentrated effluent requires a long time of treatment of around 6 h with a 400 A/m"2 current density. The aluminium alloy was found to be more efficient than pure aluminium for removal of COD and chromium. Dilution of the waste has been tested for treatment: high abatement levels could be obtained with shorter time of treatment and lower current densities. Energy consumption of the electrocoagulation process was also discussed. The dilution by half of the concentrated waste leads to a higher abatement performance of both COD and chromium with the best energy efficiency.

Treatment of highly concentrated tannery wastewater using electrocoagulation: Influence of the quality of aluminium used for the electrode

Energy Technology Data Exchange (ETDEWEB)

Elabbas, S.; Ouazzani, N.; Mandi, L. [Laboratoire d’Hydrobiologie, Ecotoxicologie et Assainissement (LHEA, URAC 33), Faculté de Sciences Semlalia, BP 2390, Université Cadi Ayyad, Marrakech (Morocco); Centre National d’Etude et de Recherche sur l’Eau et l’Energie (CNEREE), Université Cadi Ayyad, BP 511, Marrakech (Morocco); Berrekhis, F. [Equipe de Physico-chimie des Matériaux, Ecole Normale Supérieure, Université Cadi Ayyad, BP 2400, 40000 Marrakech (Morocco); Perdicakis, M. [Laboratoire de Chimie Physique et Microbiologie pour l’Environnement (LCPME) UMR 7564, Université de Lorraine—CNRS, 405 rue de Vandoeuvre, F-54602 Villers-lès Nancy Cedex (France); Pontvianne, S.; Pons, M-N.; Lapicque, F. [Laboratoire Réactions et Génie des Procédés (LRGP) UMR 7274, CNRS, Université de Lorraine, 1 rue Grandville, BP 20451, 54001 Nancy cedex (France); Leclerc, J-P, E-mail: jean-pierre.leclerc@univ-lorraine.fr [Laboratoire Réactions et Génie des Procédés (LRGP) UMR 7274, CNRS, Université de Lorraine, 1 rue Grandville, BP 20451, 54001 Nancy cedex (France)

2016-12-05

Highlights: • COD and Cr(III) species can be simultaneously removed by electrocoagulation. • Cu-containing Al alloy is more efficient than pure Al as electrodes. • Dilution of too concentrated tannery wastewater is required for efficient treatment. - Abstract: This paper deals with the ability of electrocoagulation (EC) to remove simultaneously COD and chromium from a real chrome tanning wastewater in a batch stirred electro-coagulation cell provided with two aluminium-based electrodes (aluminium/copper/magnesium alloy and pure aluminium). Effects of operating time, current density and initial concentration of Cr(III) and COD have been investigated. The concentrations of pollutants have been successfully reduced to environmentally acceptable levels even if the concentrated effluent requires a long time of treatment of around 6 h with a 400 A/m{sup 2} current density. The aluminium alloy was found to be more efficient than pure aluminium for removal of COD and chromium. Dilution of the waste has been tested for treatment: high abatement levels could be obtained with shorter time of treatment and lower current densities. Energy consumption of the electrocoagulation process was also discussed. The dilution by half of the concentrated waste leads to a higher abatement performance of both COD and chromium with the best energy efficiency.

Latex Rubber Gloves as a Sampling Dosimeter Using a Novel Surrogate Sampling Device.

Science.gov (United States)

Sankaran, Gayatri; Lopez, Terry; Ries, Steve; Ross, John; Vega, Helen; Eastmond, David A; Krieger, Robert I

2015-01-01

Pesticide exposure during harvesting of crops occurs primarily to the workers' hands. When harvesters wear latex rubber gloves for personal safety and hygiene harvesting reasons, gloves accumulate pesticide residues. Hence, characterization of the gloves' properties may be useful for pesticide exposure assessments. Controlled field studies were conducted using latex rubber gloves to define the factors that influence the transfer of pesticides to the glove and that would affect their use as a residue monitoring device. A novel sampling device called the Brinkman Contact Transfer Unit (BCTU) was constructed to study the glove characteristics and residue transfer and accumulation under controlled conditions on turf. The effectiveness of latex rubber gloves as sampling dosimeters was evaluated by measuring the transferable pesticide residues as a function of time. The validation of latex rubber gloves as a residue sampling dosimeter was performed by comparing pesticide transfer and dissipation from the gloves, with the turf transferable residues sampled using the validated California (CA) Roller, a standard measure of residue transfer. The observed correlation (Pearson's correlation coefficient R(2)) between the two methods was .84 for malathion and .96 for fenpropathrin, indicating that the BCTU is a useful, reliable surrogate tool for studying available residue transfer to latex rubber gloves under experimental conditions. Perhaps more importantly, these data demonstrate that latex gloves worn by workers may be useful quantifiable matrices for measuring pesticide exposure.

The effect of proteins on the aging properties of radiation vulcanized natural rubber latex

International Nuclear Information System (INIS)

Abad, L.V.

1993-01-01

The effect of natural rubber latex (NRL) proteins on the aging properties of NRL films was investigated. SDS-PAGE electrophoresis of the rubber proteins in NRL (Sri-Lanka) indicated a total of 18 proteins. A sharp decrease in tensile strength was observed after aging when NRL films were leached in 1% NH 4 OH. However, when these films were soaked in ethanol prior to leaching, the aging properties approximated those of the unleashed samples. Electrophoretic analysis of the proteins present in the NH 3 extracts of leached RVNRL films showed a high concentration of the protein herein. This protein was not found in the NH 3 extracts of ethanol soaked films. NRL proteins were shown to decelerate the aging process of Radiation Vulcanized Natural Rubber Latex (RVNRL) films. Among the proteins, herein exhibited good anti-aging properties. The hydrolyzates from NR proteins also enhanced considerably the aging properties of RVNRL. (auth.). 8 refs.; 40 figs.; 30 tabs

Labbtex: Toolbox para generación de informes en LATEX para Matlab

Directory of Open Access Journals (Sweden)

José Luis Almazán Gárate

2012-10-01

Full Text Available En este artículo se presenta el software desarrollado por el Equipo H3lite dentro del Departamento de Ingeneniería Civil. Transportes de la Escuela de Ingenieros de Caminos, Canales y Puertos de la Universidad Politécnica de Madrid para la generación de informes enLATEX mediante el software Matlab® y la integración en sus rutinas, Labbtex.La librería Labbtex proporciona un marco flexible para mezclar texto y código Matlab® para la generación automática de documentos. Un rchivo fuente simple contiene el texto de documentación y el código Matlab, al correr la aplicación se genera un documento final LATEX que contiene el texto, gráficos y tablas indicados con el formato de un documento LATEX. El código Matlab genera un documento LATEX usando la sintaxis. Así, LATEX (para composición de texto de alta calidad y Matlab® (para cálculo matemático pueden usarse simultáneamente. Esto permite la generación de informes en tiempo real con un uso de recursos mínimo.

Latex Allergy - A Case Report

Directory of Open Access Journals (Sweden)

Dr. Athma Prasanna

2005-10-01

Full Text Available The usage of rubber and its products are not uncommon in various walks of life. A continuous exposure or contact may sensitize the human body, causing reactions from mild to fatal. Despite the availability of the literature, medical personnel are still unaware of the implications of the use of latex materials.

Solid state NMR and LVSEM studies on the hardening of latex modified tile mortar systems

International Nuclear Information System (INIS)

Rottstegge, J.; Arnold, M.; Herschke, L.; Glasser, G.; Wilhelm, M.; Spiess, H.W.; Hergeth, W.D.

2005-01-01

Construction mortars contain a broad variety of both inorganic and organic additives beside the cement powder. Here we present a study of tile mortar systems based on portland cement, quartz, methyl cellulose and different latex additives. As known, the methyl cellulose stabilizes the freshly prepared cement paste, the latex additive enhances final hydrophobicity, flexibility and adhesion. Measurements were performed by solid state nuclear magnetic resonance (NMR) and low voltage scanning electron microscopy (LVSEM) to probe the influence of the latex additives on the hydration, hardening and the final tile mortar properties. While solid state NMR enables monitoring of the bulk composition, scanning electron microscopy affords visualization of particles and textures with respect to their shape and the distribution of the different phases. Within the alkaline cement paste, the poly(vinyl acetate) (VAc)-based latex dispersions stabilized by poly(vinyl alcohol) (PVA) were found to be relatively stable against hydrolysis. The influence of the combined organic additives methyl cellulose, poly(vinyl alcohol) and latexes stabilized by poly(vinyl alcohol) on the final silicate structure of the cement hydration products is small. But even small amounts of additives result in an increased ratio of ettringite to monosulfate within the final hydrated tile mortar as monitored by 27 Al NMR. The latex was found to be adsorbed to the inorganic surfaces, acting as glue to the inorganic components. For similar latex water interfaces built up by poly(vinyl alcohol), a variation in the latex polymer composition results in modified organic textures. In addition to the networks of the inorganic cement and of the latex, there is a weak network build up by thin polymer fibers, most probably originating from poly(vinyl alcohol). Besides the weak network, polymer fibers form well-ordered textures covering inorganic crystals such as portlandite

Current as an indicator of ammonia concentration during wastewater treatment in an integrated microbial electrolysis cell - Nitrification system

DEFF Research Database (Denmark)

Zhao, Nannan; Angelidaki, Irini; Zhang, Yifeng

2018-01-01

with synthetic ammonia-rich wastewater. A good linear relationship (R2 = 0.9419) was observed between current (0.5130–3.906 mA) and ammonia levels (0–62.1 mg NH4+-N/L). Such linear relationship was always obtained regardless of the tested external power supply or wastewater pH. The external electrochemical cell......A key challenge for ammonia monitoring during nitrogen removal process is the extra cost and toxic reagent consuming. Herein the feasibility of current generated by an integrated microbial electrolysis cell (MEC) - nitrification reactor as an indicator of initial ammonia levels (NH3/NH4......+) in wastewater was explored. In this loop system, ammonia was first oxidized to nitrate in the nitrification reactor, and then the effluent was introduced into the cathode of MEC where nitrate was reduced as electron acceptor. The correlation between current and ammonia concentration was first investigated...

Latex medical gloves

DEFF Research Database (Denmark)

Palosuo, Timo; Antoniadou, Irini; Gottrup, Finn

2011-01-01

Many hospitals have implemented policies to restrict or ban the use of devices made of natural rubber latex (NRL) in healthcare as precautionary measures against the perceived risk of NRL allergy. Changes in glove technology, progress in measuring the specific allergenic potential of gloves...... properties of NRL and synthetic gloves and the role of glove powder. The review shows that NRL medical gloves, when compared with synthetic gloves, tend to be stronger, more flexible and better accepted by clinicians. The introduction of powder-free gloves has been associated with reductions in protein...

The role of proteins on the thermal oxidative aging of radiation vulcanized natural rubber latex

International Nuclear Information System (INIS)

Abad, L.V.; Rosa, A. de la; Keizo Makuuchi; Fumio Yoshii

1996-01-01

The effect of Hevea latex proteins on the aging properties of radiation vulcanized natural rubber latex (RVNRL) was investigated. Unpurified RVNRL films exhibited better aging properties than the purified RVNRL films. A sharp decrease in tensile strength was observed after aging when RVNRL films were leached in 1% NH sub 4 OH. However, when these films were soaked in ethanol prior to leaching, the aging properties approximated those of the unleached samples. Kjeldahl and FT-IR analyses of the leached and unleached RVNRL films indicated a higher protein content for both the unleached and ethanol-soaked films than for leached films. Electrophoretic analysis of the proteins present in the NH, extracts of leached RVNRL films showed a high concentration of hevein. This protein was not found in the ATH, extracts of ethanol soaked films. Hevein was shown to improve the aging properties of RVNRL

Formation of Defect-Free Latex Films on Porous Fiber Supports

KAUST Repository

Lively, Ryan P.

2011-09-28

We present here the creation of a defect-free polyvinylidene chloride barrier layer on the lumen-side of a hollow fiber sorbent. Hollow fiber sorbents have previously been shown to be promising materials for enabling low-cost CO 2 capture, provided a defect-free lumen-side barrier layer can be created. Film experiments examined the effect of drying rate, latex age, substrate porosity (porous vs nonporous), and substrate hydrophobicity/ hydrophilicity. Film studies show that in ideal conditions (i.e., slow drying, fresh latex, and smooth nonporous substrate), a defect-free film can be formed, whereas the other permutations of the variables investigated led to defective films. These results were extended to hollow fiber sorbents, and despite using fresh latex and relatively slow drying conditions, a defective lumen-side layer resulted. XRD and DSC indicate that polyvinylidene chloride latex develops crystallinity over time, thereby inhibiting proper film formation as confirmed by SEM and gas permeation. This and other key additional challenges associated with the porous hollow fiber substrate vs the nonporous flat substrate were overcome. By employing a toluene-vapor saturated drying gas (a swelling solvent for polyvinylidene chloride) a defect-free lumen-side barrier layer was created, as investigated by gas and water vapor permeation. © 2011 American Chemical Society.

Isotactic polypropylene/carbon nanotube composites prepared by latex technology: Electrical conductivity study

NARCIS (Netherlands)

Grossiord, N.; Wouters, M.E.L.; Miltner, H.E.; Lu, K.; Loos, J.; Van Mele, B.; Koning, C.E.

2010-01-01

Several series of nanocomposites were prepared using a latex-based process, the main step of which consisted of mixing an aqueous suspension of exfoliated carbon nanotubes (CNTs) and a polymer latex. In the present work, a systematic study on the electrical properties of fully amorphous (polystyrene

THE EFFECT OF INFLUENT CONCENTRATION AND HYDRAULIC LOADING RATE (HLR TO BOD AND COD REMOVAL ON ARTIFICIAL DOMESTIC WASTEWATER TREATMENT (GREY WATER USING UASB REACTOR

Directory of Open Access Journals (Sweden)

Syafrudin Syafrudin

2014-05-01

Full Text Available Upflow anaerobic sludge blanket (UASB reactor is one of anaerobic biological treatment was develop in late 1970’s. UASB reactor is suitable for the tropic areas because it has a high temperature about 20°-30°C. Domestic wastewater is divided into two types, namely black water and grey water. But in this case used domestic grey water. Grey water is household wastewater from showers, sinks and kitchen. Grey water has a total 75% of the domestic wastewater volume. The research was conducted in laboratory scale. This study performed a variation of Hydraulic Loading Rate (HLR and the influent concentration. There were 25 reactors include 5 variations of influent concentration and 5 Hydraulic Loading Rate’s (HLR variation. The research could asses BOD5 and COD removal with treatment in UASB. Efficiency of BOD5 removal by varying the influent concentration and HLR was about 38%-75% and COD was about 40%-77%. The lower concentration could be increase efficiency BOD5 and COD removal. Influent concentration optimum occurred when middle concentration was about 840 mg/L COD and HLR optimum was 0,05 m3/m2/hour.

Proceedings of the international symposium on radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Machi, Sueo

1990-01-01

The First International Symposium on Radiation Vulcanization of Natural Rubber Latex (RVNRL) was held from 26 to 28 July 1989 at Tokyo and Takasaki. In these proceedings, thirty six papers presented at the Symposium are compiled. Main topics are commercial application of RVNRL, characterization of NR latex and vulcanization, properties of radiation vulcanized NR latex, development of sensitizers, mechanism of RVNRL, RVNRL with electron beams, and new Co-60 irradiator for RVNRL. Absence of nitrosamines and low cytotoxicity of radiation vulcanized NR latex are recognized as the remarkable advantages of RVNRL. The radiation vulcanization process for the production of protective rubber gloves for radioactive contamination was presented as the first commercial success in RVNRL. It was reported that various kinds of rubber articles for medical uses have being developed in West Germany. A sensitizer system consisting of n-butyl acrylate and t-butyl hydroperoxide was found to reduce the vulcanization dose to 8 kGy. (author)

CDNA library from the Latex of Hevea brasiliensis

Directory of Open Access Journals (Sweden)

Wilaiwan Chotigeat

2010-12-01

Full Text Available Latex from Hevea brasiliensis contains 30-50% (w/w of natural rubber (cis-1,4-polyisoprene, the important rawmaterial for many rubber industries. We have constructed a cDNA library from the latex of H. brasiliensis to investigate theexpressed genes and molecular events in the latex. We analyzed 412 expressed sequence tags (ESTs. More than 90% of theEST clones showed homology to previously described sequences in public databases. Functional classification of the ESTsshowed that the largest category were proteins of unknown function (30.1%, 11.4% of ESTs encoded for rubber synthesisrelatedproteins (RS and 8.5% for defense or stress related proteins (DS. Those with no significant homology to knownsequences (NSH accounted for 8.7%, primary metabolism (PM and gene expression and RNA metabolism were 7.8% and6.6%, respectively. Other categories included, protein synthesis-related proteins (6.6%, chromatin and DNA metabolism(CDM 3.9%, energy metabolism (EM 3.4%, cellular transport (CT 3.2%, cell structure (CS 3.2%, signal transduction (ST2.2%, secondary metabolism (SM 1.7%, protein fate (PF 2.2%, and reproductive proteins (RP 0.7%.

Pilot scale experiments on radiation vulcanization of NR latex

Science.gov (United States)

Ridwan, M.

The potential of irradiated latex as raw material of commercial use is under testing on pilot plant scale in Indonesia which has 225 kCi Co-60 irradiation facility and can irradiate 1000 tonnes of centrifuged latex per annum. The facility was jointly designed by BATAN of Indonesia and JAERI of Japan and was jointly financed by UNDP/IAEA, Government of Japan and Government of Indonesia under UNDP/IAEA Regional Cooperative Agreement Project on Industrial Application of Isotopes and Radiation Technology. The facility is a water pool type and can accomodate 400 kCi Co-60. The Co-60 rack has two shapes, plate and cylindrical shapes. The plate shape source is used for natural rubber latex irradiation and the cylindrical one is used for other irradiation services. The vulcanization system consists of three major components : emulsification unit ( height : 650 mm, diameter 500 mm ), mixing unit ( height : 1900mm, diameter 1200 mm ) and vulcanization reactor ( height : 1800 mm, diameter 1300 mm ). The first two components are located outside shielded room while the third one-in irradiation room. The radiation vulcanization process is a much simpler energy saving process comparedto the conventional thermal process which has two vulcanization steps before and after dipping. The physical and mechanical properties of irradiated NR Latex are comparable to those of sulfur vulcanized, and depend on many factors such as irradiation dose, sensitizer content, dry rubber content and storage time.

Mixtures of latex particles and the surfactant of opposite charge used as interface stabilizers--influence of particle contact angle, zeta potential, flocculation and shear energy.

Science.gov (United States)

Deleurence, Rémi; Parneix, Caroline; Monteux, Cécile

2014-09-28

We investigate the stabilization of air-water interfaces by mixtures of negatively charged latex particles (sulfate polystyrene) and cationic surfactants (alkyl trimethylammonium bromides). First we report results concerning the binding of surfactant molecules to the latex particles. As the surfactant concentration increases, the charge of the particles reverses, from negative to positive, because CnTAB first binds electrostatically to the latex particles and then through hydrophobic interaction with the monolayer already adsorbed on the particles as well as directly with the hydrophobic surface of the latex. Over a large range of surfactant concentrations around the charge inversion, a strong flocculation is observed and 100 μm large aggregates form in the suspension. Unlike previous studies published on mixtures of inorganic particles with oppositely charged surfactants, we show that we can vary the sign of the zeta potential of the particles without changing the contact angle of the particles over a large range of surfactant concentrations. Indeed, the latex particles that we study are more hydrophobic than inorganic particles, hence adding moderate concentrations of the surfactant results in a weak variation of the contact angle while the charge of the particles can be reversed. This enables decoupling of the effect of zeta potential and contact angle on the interfacial properties of the mixtures. Our study shows that the contact angle and the charge of the particles are not sufficient parameters to control the foam properties, and the key-parameters are the flocculation state and the shear energy applied to produce the foam. Indeed, flocculated samples, whatever the sign of the zeta potential, enable production of a stable armour at the interface. The large aggregates do not adsorb spontaneously at the interface because of their large size, however when a large shear energy is used to produce the foam very stable foam is obtained, where particles are trapped

Latex imaging by environmental STEM: application to the study of the surfactant outcome in hybrid alkyd/acrylate systems.

Science.gov (United States)

Faucheu, Jenny; Chazeau, Laurent; Gauthier, Catherine; Cavaillé, Jean-Yves; Goikoetxea, Monika; Minari, Roque; Asua, José M

2009-09-01

Among other uses, latexes are a successful alternative to solvent-borne binders for coatings. Efforts are made to produce hybrid nanostructured latexes containing an acrylic phase and an alkyd phase. However, after the film-forming process, the surfactant used to stabilize these latexes remains in the film, and its location can have a drastic effect on the application properties. Among the processing parameters, the alkyd hydrophobicity can strongly influence this location. This article aims at the imaging of these surfactant molecules in two hybrid latexes with different hydrophobicity level of the alkyd resin. A first part of this paper is dedicated to the understanding of the contrast provided by the surfactant in environmental STEM imaging of latexes. Then, the influence of surfactant-polymer affinity on the surfactant location after film-forming of those hybrid alkyd/acrylate latexes is studied by this technique. It is shown that in the hybrid latex with an alkyd shell (obtained with the most hydrophilic resin), the surfactant molecules tend to remain buried in the alkyd phase. Conversely, in the hybrid latex with an acrylate shell (in the case of the most hydrophobic resin), the surfactant molecules tend to gather into islands like in pure acrylate latex films.

Latex-modified grouts for in-situ stabilization of buried transuranic/mixed waste

International Nuclear Information System (INIS)

Allan, M.L.

1996-06-01

The Department of Applied Science at Brookhaven national Laboratory was requested to investigate latex-modified grouts for in-situ stabilization of buried TRU/mixed waste for INEL. The waste exists in shallow trenches that were backfilled with soil. The objective was to formulate latex-modified grouts for use with the jet grouting technique to enable in-situ stabilization of buried waste. The stabilized waste was either to be left in place or retrieved for further processing. Grouting prior to retrieval reduces the potential release of contaminants. Rheological properties of latex-modified grouts were investigated and compared with those of conventional neat cement grouts used for jet grouting

Concentrations and Toxic Equivalency of Polychlorinated Biphenyls in Polish Wastewater Treatment Plant Effluents.

Science.gov (United States)

Urbaniak, Magdalena; Kiedrzyńska, Edyta

2015-10-01

Wastewater treatment plants (WWTPs) are widely recognized as important sources of toxic contaminants such as polychlorinated biphenyls (PCBs). An example is given in the present paper, where concentrations of 12 dioxin-like PCBs (dl-PCBs) congeners were investigated in effluents from 14 WWTPs of different sizes, using gas chromatography tandem-mass spectrometry. The results obtained demonstrate that the smallest WWTPs are characterized by the highest total dl-PCB concentration of 102.69 pg/L, roughly twice those of medium-size and large WWTPs, i.e. 41.14 and 48.29 pg/L, respectively. In all cases, the concentrations obtained were generated mostly by increased contributions of PCB-77, PCB-105 and PCB-118 which constituted 48 %-59 % of the mean dl-PCB concentration. The results also reveal a predominance of mono-ortho over non-ortho PCBs. All three types of WWTP effluent were found to have similar toxic equivalency (TEQ) values, ranging from 0.31 for large to 0.37 pg TEQ/L for medium WWTPs.

Phytotoxicity testing of winery wastewater for constructed wetland treatment.

Science.gov (United States)

Arienzo, Michele; Christen, Evan W; Quayle, Wendy C

2009-09-30

Rapid and inexpensive phytotoxicity bioassays for winery wastewater (WW) are important when designing winery wastewater treatment systems involving constructed wetlands. Three macrophyte wetland species (Phragmites australis, Schoenoplectus validus and Juncus ingens) were tested using a pot experiment simulating a wetland microcosm. The winery wastewater concentration was varied (0.5%, 5%, 10%, 25%, 50%, 75% and 100%) and pH was corrected for some concentrations using lime as an amendment. The tolerance of the three aquatic macrophytes species to winery wastewater was studied through biomass production, total chlorophyll and nitrogen, phosphorous and potassium tissue concentrations. The results showed that at greater than 25% wastewater concentration all the macrophytes died and that Phragmites was the least hardy species. At less than 25% wastewater concentration the wetland microcosms were effective in reducing chemical oxygen demand, phenols and total soluble solids. We also evaluated the performance of two laboratory phytotoxicity assays; (1) Garden Cress (Lepidium sativum), and (2) Onion (Allium coepa). The results of these tests revealed that the effluent was highly toxic with effective concentration, EC(50), inhibition values, as low as 0.25%. Liming the WW increased the EC(50) by 10 fold. Comparing the cress and onion bioassays with the wetland microcosm results indicated that the thresholds for toxicity were of the same order of magnitude. As such we suggest that the onion and cress bioassays could be effectively used in the wine industry for rapid wastewater toxicity assessment.

Radiation vulcanization of natural rubber latex with low energy accelerator-II

Energy Technology Data Exchange (ETDEWEB)

Haque, Md. Emdadul; Makuuchi, Keizo; Ikeda, Kenichi; Yoshii, Fumio; Kume, Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Mitomo, Hiroshi [Gunma Univ., Faculty of Engineering, Dept. of Biological and Chemical Engineering, Kiryu, Gunma (Japan)

2002-03-01

The natural rubber latex (NRL) was radiation vulcanized under a low energy electron accelerator. Accelerating voltage and maximum beam current of this accelerator are 250 kV and 10 mA respectively. Irradiation was carried out in a reaction vessel with constant stirring. The capacity of the vessel is 18 liters. Radiation vulcanization accelerators (RVA) were normal butyl acrylate (n-BA) and nonane-diol-diacrylate (NDDA). NDDA has no bad smell like that of n-BA. 20 minutes irradiation time is enough to vulcanize 14 liters of latex when 5 phr RVA (both types) are used. Maximum of {approx}30 MPa tensile strength was obtained with 5 phr NDD-A. However the remained NDDA is difficult to remove due to high molecular weight. Water-extractable proteins content was determined in dipped films for various leaching conditions without and with additive (polyvinyl alcohol, PVA). Water extractable proteins content is reduced to {<=} 41 by adding 5 phr PVA and leaching for 8 hours. The tackiness of the dipped films is reduced to 0.1 from 9 gf by mixing 6 phr PVA with the irradiated latex. Hand gloves (surgical and examination) were successfully produced from the irradiated latex. (author)

Biodegradability and aging study of rubber films obtained by gamma radiation vulcanization processes of latex

International Nuclear Information System (INIS)

Martins, Carlos Felipe Pinto

2005-01-01

The natural rubber latex (NRL) is industrially crosslinked by the conventional process of vulcanization, which uses sulphur and heat. Otherwise, the network can also be done by the alternative process with ionizing radiation. In this work the crosslinking of NRL was studied by the comparison of the conventional vulcanization system and the ionizing radiation process of 60 C source. The products obtained, the irradiated latex, the irradiated latex with approximately 1% of soy lecithin and the sulphur vulcanized latex were tested by accelerated aging with ultraviolet (UV) and outdoor aging with compostage, tensile strength at break, swelling and gel fraction, fungi micro biota, scanning electron microscopy (SEM), infrared spectroscopy (FTIR) and thermogravimetry and differential scanning calorimetry analysis (TG and DSC). The results showed that the aging with microorganisms have a great influence in the physical properties of the samples. The thermal stability order observed showed that the sulphur vulcanized latex is more resistant, what is probably associated to a network more stable under the aging conditions. On the other hand, the irradiated latex showed intense biodegradation aspects, particularly with the presence of the soy lecithin. (author)

Tofu wastewater treatment by sediment microbial fuel cells

Science.gov (United States)

Rinaldi, W.; Abubakar; Rahmi, R. F.; Silmina

2018-03-01

This research aimed to measure power density generated by sediment microbial fuel cells (SMFCs) by varying anode position and wastewater concentration. Anode position was varied at 2 cm and 4 cm under the surface of sediment, while wastewater concentration varied into 25%, 50%, 75% and 100%. The electrodes employed was stainless steel mesh, while the organic subtrate source was taken from wastewater of soybean washing and boiling process. The sediment was taken from the Lamnyong River around the outlet of tofu industry wastewater. SMFCs was run until the power density was relatively small. The produced electricity represented in power density. The results of this research showed that power density was decreased over time. Generated power density by varying 2 cm and 4 cm position of anode under the sediment surface was not significantly different, while the lowest wastewater concentration, 25%, gave the highest power density.

Organic Wastewater Compounds, Pharmaceuticals, andColiphage in Ground Water Receiving Discharge from OnsiteWastewater Treatment Systems near La Pine, Oregon:Occurrence and Implications for Transport

Science.gov (United States)

Hinkle, Stephen J.; Weick, Rodney J.; Johnson, Jill M.; Cahill, Jeffery D.; Smith, Steven G.; Rich, Barbara J.

2005-01-01

The occurrence of organic wastewater compounds (components of 'personal care products' and other common household chemicals), pharmaceuticals (human prescription and nonprescription medical drugs), and coliphage (viruses that infect coliform bacteria, and found in high concentrations in municipal wastewater) in onsite wastewater (septic tank effluent) and in a shallow, unconfined, sandy aquifer that serves as the primary source of drinking water for most residents near La Pine, Oregon, was documented. Samples from two types of observation networks provided basic occurrence data for onsite wastewater and downgradient ground water. One observation network was a group of 28 traditional and innovative (advanced treatment) onsite wastewater treatment systems and associated downgradient drainfield monitoring wells, referred to as the 'innovative systems network'. The drainfield monitoring wells were located adjacent to or under onsite wastewater treatment system drainfield lines. Another observation network, termed the 'transect network', consisted of 31 wells distributed among three transects of temporary, stainless-steel-screened, direct-push monitoring wells installed along three plumes of onsite wastewater. The transect network, by virtue of its design, also provided a basis for increased understanding of the transport of analytes in natural systems. Coliphage were frequently detected in onsite wastewater. Coliphage concentrations in onsite wastewater were highly variable, ranging from less than 1 to 3,000,000 plaque forming units per 100 milliliters. Coliphage were occasionally detected (eight occurrences) at low concentrations in samples from wells located downgradient from onsite wastewater treatment system drainfield lines. However, coliphage concentrations were below method detection limits in replicate or repeat samples collected from the eight sites. The consistent absence of coliphage detections in the replicate or repeat samples is interpreted to indicate

Thermodynamics of swelling of latex particles with two monomers: a sensitivity analysis

NARCIS (Netherlands)

Maxwell, I.A.; Noel, E.F.J.; Schoonbrood, H.A.S.; German, A.L.

1993-01-01

A sensitivity anal. is performed to det. at what conditions the simplified model for swelling of latex particles by two monomers or two solvents is valid. This model proposes that, inter alia, the fractions of two monomers in the latex particles and in the monomer droplets are equal. The model is a

Color Spectrum Properties of Pure and Non-Pure LATEX in Discriminating Rubber Clone Series

International Nuclear Information System (INIS)

Noor Aishah Khairuzzaman; Hadzli Hashim; Nina Korlina Madzhi; Noor Ezan Abdullah; Faridatul Aima Ismail; Ahmad Faiz Sampian; Azhana Fatnin Che Will

2015-01-01

A study of color spectrum properties for pure and non-pure latex in discriminating rubber clone series has been presented in this paper. There were five types of clones from the same series being used as samples in this study named RRIM2002, RRIM2007, RRIM2008, RRIM2014, and RRIM3001. The main objective is to identify the significant color spectrum (RGB) from pure and non-pure latex that can discriminate rubber clone series. The significant information of color spectrum properties for pure and non-pure latex is determined by using spectrometer and Statistical Package for the Social Science (SPSS). Visible light spectrum (VIS) is used as a radiation light of the spectrometer to emit light to the surface of the latex sample. By using SPSS software, the further numerical analysis of color spectrum properties is being conducted. As the conclusion, blue color spectrum for non-pure is able to discriminate for all rubber clone series whereas only certain color spectrum can differentiate several clone series for pure latex. (author)

Detection of a wide variety of human and veterinary fluoroquinolone antibiotics in municipal wastewater and wastewater-impacted surface water.

Science.gov (United States)

He, Ke; Soares, Ana Dulce; Adejumo, Hollie; McDiarmid, Melissa; Squibb, Katherine; Blaney, Lee

2015-03-15

As annual sales of antibiotics continue to rise, the mass of these specially-designed compounds entering municipal wastewater treatment systems has also increased. Of primary concern here is that antibiotics can inhibit growth of specific microorganisms in biological processes of wastewater treatment plants (WWTPs) or in downstream ecosystems. Growth inhibition studies with Escherichia coli demonstrated that solutions containing 1-10 μg/L of fluoroquinolones can inhibit microbial growth. Wastewater samples were collected on a monthly basis from various treatment stages of a 30 million gallon per day WWTP in Maryland, USA. Samples were analyzed for the presence of 11 fluoroquinolone antibiotics. At least one fluoroquinolone was detected in every sample. Ofloxacin and ciprofloxacin exhibited detection frequencies of 100% and 98%, respectively, across all sampling sites. Concentrations of fluoroquinolones in raw wastewater were as high as 1900 ng/L for ciprofloxacin and 600 ng/L for ofloxacin. Difloxacin, enrofloxacin, fleroxacin, moxifloxacin, norfloxacin, and orbifloxacin were also detected at appreciable concentrations of 9-170 ng/L. The total mass concentration of fluoroquinolones in raw wastewater was in the range that inhibited E. coli growth, suggesting that concerns over antibiotic presence in wastewater and wastewater-impacted surface water are valid. The average removal efficiency of fluoroquinolones during wastewater treatment was approximately 65%; furthermore, the removal efficiency for fluoroquinolones was found to be negatively correlated to biochemical oxygen demand removal and positively correlated to phosphorus removal. Copyright © 2014 Elsevier B.V. All rights reserved.

Extractable proteins from electron beam (EB) irradiated natural rubber (NR) latex

International Nuclear Information System (INIS)

Feroza Akhtar; Fumio Yoshii; Keizo Makuuchi

1996-01-01

The protein assay of natural rubber latex (NRL) vulcanized by low energy electron beam (EB, 300 keV, 30 mA) has been carried out using Bicinchoninic acid (BCA) reagent. Extractable protein in irradiated latex film was determined by measuring the absorption of colored solution at 562 nm using UV spectrometer. The effect of various radiation doses on the extractable protein content of NRL was investigated. It was ,found that the quantities of extractable protein increases with radiation dose. When compared with ,gamma-ray irradiated samples the same trend was observed. Electron beam irradiated latex films are leached in 1% (ammonia water for various lengths of time. From the results it was established that within 2 hours of leaching in ammonia water most of the extractable protein (96%) were removed from rubber film

Antioxidant and sensitizer effect on the stability of natural rubber latex vulcanized by gamma rays

International Nuclear Information System (INIS)

Canavel, V.

1993-01-01

The natural rubber latex was vulcanized by gamma rays and electrons beam, in the presence and absence of sensitizer at room temperature. The sensitizers were the following; n-butyl acrylate (n-BA) / t-butyl hydroperoxide (t-B H) / KOH, C Cl 4 / potassium laurate and n-BA / KOH. The studied antioxidants, Irganox 1520, Vulcanox SP and Vulcanox BKF, were added to the latex after irradiation. Among the studied antioxidants in function of tensile strength (TS) after the aging of rubber plates, the Irganox was the best efficient on the gamma vulcanization in the presence of n-BA/t-B H/KOH, because only 0,20 p hr is enough to obtain the greatest increase of TS, that was 34%, 12 MPa to 16 MPa. The formulating method of latex with the sensitizer constituted the 3,0 p hr of n-BA/ 0,1 p hr of t-B H and 0,2 p hr of KOH, was evaluated respecting the TS of rubber plates. The electrons beam vulcanization produces the greatest reversible perturbance in the colloidal stability of latex after irradiation caused by radiolytic species absorption that promotes the increase of particle size. The antioxidant also contributes to reversible destabilization of gamma irradiated latex, because it is also adsorbed by particles surface. The relation between the latex viscosity and the TS of respective rubber plates is reverse, showing the latex stability affects the quality of rubber goods. (author)

The entry of free radicals into polystyrene latex particles

International Nuclear Information System (INIS)

Adams, M.E.; Trau, M.; Gilbert, R.C.; Napper, D.R.

1988-01-01

Mechanistic understanding of the processes governing the kinetics of emulsion polymerization has both scientific and technical interest. One component of this process that is poorly understood at present is that of free radical entry into latex particles. Measurements were made of the entry rate coefficient as a function of temperature for free radicals entering polystyrene latex particles in seeded emulsion polymerizations initiated by γ-rays. The activation energy for entry was found to be less than 24 ± 3 kJ mol -1 , consistent with entry being controlled by a physical (e.g. diffusional) rather than a chemical process. Measurement of the entry rate coefficient as a function of the γ-ray dose rate suggested that the factors that determine the entry rate when the primary free radicals are uncharged are similar to those that determine the entry rate for charged free radicals derived from chemical initiation by peroxydisulfate. This result was consistent with measurements of the entry rate coefficient of charged free radicals derived from peroxydisulfate; these data were found to be virtually independent of both the extent of the latex surface coverage by the anionic surfactant sodium dodecyl sulfate and the ionic strength of the continuous phase. The data refute several proposals given in the literature for the rate-determining step for entry, being inconsistent with control by collision of free radicals with the latex particles, surfactant desorption, and an electrostatic barrier arising from the colloidal nature of the entering free radical. The origin of the activation energy for entry remains obscure

Hierarchically structured self-supported latex films for flexible and semi-transparent electronics

International Nuclear Information System (INIS)

Määttänen, Anni; Ihalainen, Petri; Törngren, Björn; Rosqvist, Emil; Pesonen, Markus; Peltonen, Jouko

2016-01-01

Graphical abstract: - Highlights: • Transparent self-supported latex films were fabricated by a peel-off process. • Various template substrates were used for creating e.g. hierarchically structured latex films. • Ultra-thin and semi-transparent conductive gold electrodes were evaporated on the latex films.Electrochemical experiments were carried out to verify the applicability of the electrodes. - Abstract: Different length scale alterations in topography, surface texture, and symmetry are known to evoke diverse cell behavior, including adhesion, orientation, motility, cytoskeletal condensation, and modulation of intracellular signaling pathways. In this work, self-supported latex films with well-defined isotropic/anisotropic surface features and hierarchical morphologies were fabricated by a peel-off process from different template surfaces. In addition, the latex films were used as substrates for evaporated ultrathin gold films with nominal thicknesses of 10 and 20 nm. Optical properties and topography of the samples were characterized using UV–vis spectroscopy and Atomic Force Microscopy (AFM) measurements, respectively. The latex films showed high-level transmittance of visible light, enabling the fabrication of semi-transparent gold electrodes. Electrochemical impedance spectroscopy (EIS) measurements were carried out for a number of days to investigate the long-term stability of the electrodes. The effect of 1-octadecanethiol (ODT) and HS(CH_2)_1_1OH (MuOH) thiolation and protein (human serum albumin, HSA) adsorption on the impedance and capacitance was studied. In addition, cyclic voltammetry (CV) measurements were carried out to determine active medicinal components, i.e., caffeic acid with interesting biological activities and poorly water-soluble anti-inflammatory drug, piroxicam. The results show that the fabrication procedure presented in this study enables the formation of platforms with hierarchical morphologies for multimodal (optical and

Hierarchically structured self-supported latex films for flexible and semi-transparent electronics

Energy Technology Data Exchange (ETDEWEB)

Määttänen, Anni, E-mail: anni.maattanen@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Ihalainen, Petri, E-mail: petri.ihalainen@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Törngren, Björn, E-mail: bjorn.torngren@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Rosqvist, Emil, E-mail: emil.rosqvist@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Pesonen, Markus, E-mail: markus.pesonen@abo.fi [Physics, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland); Peltonen, Jouko, E-mail: jouko.peltonen@abo.fi [Laboratory of Physical Chemistry, Faculty of Science and Engineering, Center for Functional Materials, Åbo Akademi University, Porthaninkatu 3, 20500, Turku (Finland)

2016-02-28

Graphical abstract: - Highlights: • Transparent self-supported latex films were fabricated by a peel-off process. • Various template substrates were used for creating e.g. hierarchically structured latex films. • Ultra-thin and semi-transparent conductive gold electrodes were evaporated on the latex films.Electrochemical experiments were carried out to verify the applicability of the electrodes. - Abstract: Different length scale alterations in topography, surface texture, and symmetry are known to evoke diverse cell behavior, including adhesion, orientation, motility, cytoskeletal condensation, and modulation of intracellular signaling pathways. In this work, self-supported latex films with well-defined isotropic/anisotropic surface features and hierarchical morphologies were fabricated by a peel-off process from different template surfaces. In addition, the latex films were used as substrates for evaporated ultrathin gold films with nominal thicknesses of 10 and 20 nm. Optical properties and topography of the samples were characterized using UV–vis spectroscopy and Atomic Force Microscopy (AFM) measurements, respectively. The latex films showed high-level transmittance of visible light, enabling the fabrication of semi-transparent gold electrodes. Electrochemical impedance spectroscopy (EIS) measurements were carried out for a number of days to investigate the long-term stability of the electrodes. The effect of 1-octadecanethiol (ODT) and HS(CH{sub 2}){sub 11}OH (MuOH) thiolation and protein (human serum albumin, HSA) adsorption on the impedance and capacitance was studied. In addition, cyclic voltammetry (CV) measurements were carried out to determine active medicinal components, i.e., caffeic acid with interesting biological activities and poorly water-soluble anti-inflammatory drug, piroxicam. The results show that the fabrication procedure presented in this study enables the formation of platforms with hierarchical morphologies for multimodal

Elements of the LaTeX system for the development of large publications

DEFF Research Database (Denmark)

Andersen, Esben Sloth

This document presents gives a quick overview over the LATEX system from the viewpoint of the production of books and complex papers. Thereby it provides the starting point for the author's selection of a set of LATEX packages and the development of related commands....

Prevalence of Allergy to Natural Rubber Latex and Potential Cross Reacting Food in Operation Room Staff in Shiraz Hospitals -2006

Directory of Open Access Journals (Sweden)

H Nabavizade

2007-07-01

Full Text Available Introduction & Objective: Allergic reactions to natural rubber latex have increased during past 10 years especially among health care workers and patients with high exposure to latex allergens. Allergic reaction to latex is related to many diseases like occupational asthma. This study was performed to determine the prevalence of allergy to natural rubber latex and potential cross reacting food in operation room staff in Shiraz hospitals. Materials & Methods: In this cross-sectional descriptive study five hundred eighty operation room staff of ten private and state hospitals in Shiraz completed latex allergy questionnaire. They were questioned about personal history and previous history of latex sensitivity, symptoms of latex reactivity and about other allergies particularly to foods that may cross react with latex. Informed consent was obtained and skin prick testing was performed with natural rubber latex. Skin prick tests were done with three potentially cross reacting food (banana, Kiwi, and potato. The obtained data were analyzed with SPSS software and Chi-square test. Results: Among the 580 operation room workers 104 (17.9 % of participants were positive to latex skin test. We found a significant association between positive skin test to latex in operation room staff and atopy, urticaria and food allergy. Positive skin test to latex related to positive kiwi skin test (p<0.05. The prevalence did not vary by sex, age, education, surgical and non surgical glove users, history of contact dermatitis or smoking status. Conclusion: Latex allergy has a high prevalence in personnel of operation room. Evaluation of present symptom and prediction of future disease necessitate screening test in individuals at risk.

Glove powder's carrying capacity for latex protein: analysis using the ASTM ELISA test.

Science.gov (United States)

Beezhold, D; Horton, K; Hickey, V; Daddona, J; Kostyal, D

2003-01-01

Glove donning powders carry latex proteins and disperse them into the workplace environment. We have used the ASTM D6499 ELISA to quantify the amount of latex antigen bound to and carried by glove powders. We could differentiate between a small amount of protein actually bound to the powders and a larger amount carried by the powder. Enhanced binding of a major allergen, Hev b 5, to the starch powders was demonstrated by Western blot. The D6499 ELISA is able to measure total latex antigen, soluble and powder bound, simultaneously without the need to centrifuge the samples.

Analysis of Aqueous Extractable Protein in Radiation Pre vulcanized Natural Rubber Latex (RVNRL) And Sulphur Pre vulcanized Natural Rubber Latex (SVNRL)

International Nuclear Information System (INIS)

Sofian Ibrahim; Mohd Noor Wadi Mat Lazim; Syuhada Ramli; Keong, C.C.; Khairul Hisyam Mohd Yusof; Muhammad Saiful Omar; Najib Mohd Zakey; Hafizuddin Maseri; Noor Hasni Mohd Ali

2015-01-01

The use of radiation do not only produces Radiation Pre vulcanized Natural Rubber Latex (RVNRL) that can be used for the production of nitrosamines free products, moreover, RVNRL also able to exclude type IV allergy that caused by high protein content in the products. Leaching water from production of finger coat from RVNRL and Sulphur Pre vulcanized Natural rubber Latex (SVNRL) has been collected. Extractable protein content from water samples measured according to the test protocol ASTM D5712-2010. Water from leaching process of finger coat made from RVNRL showed a higher protein content than SVNRL. This explains why RVNRL based products contain very low protein content and thus reduce the risk of Type IV allergy. (author)

Latex-mediated synthesis of ZnS nanoparticles: green synthesis approach

Energy Technology Data Exchange (ETDEWEB)

Hudlikar, Manish; Joglekar, Shreeram [University of Pune, Division of Biochemistry, Department of Chemistry (India); Dhaygude, Mayur [National Chemical Laboratory, Polymer Science and Engineering Division (India); Kodam, Kisan, E-mail: kodam@chem.unipune.ac.in [University of Pune, Division of Biochemistry, Department of Chemistry (India)

2012-05-15

A low-cost, green synthesis of ZnS nanoparticles is reported using 0.3 % latex solution prepared from Jatropha curcas L. ZnS nanoparticles were characterized by X-ray diffraction, selected area electron diffraction, transmission electron microscopy, energy dispersive analysis of X-rays, UV-vis optical absorption and photoluminescence techniques. Fourier Transform Infrared Spectroscopy was performed to find the role of cyclic peptides namely curcacycline A (an octapeptide), curcacycline B (a nonapeptide) and curcain (an enzyme) as a possible reducing and stabilizing agents present in the latex of J. curcas L. The average size of ZnS nanoparticles was found to be 10 nm. Latex of J. curcas L. itself acts as a source of sulphide (S{sup -2}) ions that are donated to Zn ions under present experimental conditions. Source of sulphide (S{sup -2}) ions is still unclear, but we speculate that cysteine or thiol residues present in enzyme curcain may be donating these sulphide (S{sup -2}) ions.

Latex-mediated synthesis of ZnS nanoparticles: green synthesis approach

Science.gov (United States)

Hudlikar, Manish; Joglekar, Shreeram; Dhaygude, Mayur; Kodam, Kisan

2012-05-01

A low-cost, green synthesis of ZnS nanoparticles is reported using 0.3 % latex solution prepared from Jatropha curcas L. ZnS nanoparticles were characterized by X-ray diffraction, selected area electron diffraction, transmission electron microscopy, energy dispersive analysis of X-rays, UV-vis optical absorption and photoluminescence techniques. Fourier Transform Infrared Spectroscopy was performed to find the role of cyclic peptides namely curcacycline A (an octapeptide), curcacycline B (a nonapeptide) and curcain (an enzyme) as a possible reducing and stabilizing agents present in the latex of J. curcas L. The average size of ZnS nanoparticles was found to be 10 nm. Latex of J. curcas L. itself acts as a source of sulphide (S-2) ions that are donated to Zn ions under present experimental conditions. Source of sulphide (S-2) ions is still unclear, but we speculate that cysteine or thiol residues present in enzyme curcain may be donating these sulphide (S-2) ions.

Latex-mediated synthesis of ZnS nanoparticles: green synthesis approach

International Nuclear Information System (INIS)

Hudlikar, Manish; Joglekar, Shreeram; Dhaygude, Mayur; Kodam, Kisan

2012-01-01

A low-cost, green synthesis of ZnS nanoparticles is reported using 0.3 % latex solution prepared from Jatropha curcas L. ZnS nanoparticles were characterized by X-ray diffraction, selected area electron diffraction, transmission electron microscopy, energy dispersive analysis of X-rays, UV–vis optical absorption and photoluminescence techniques. Fourier Transform Infrared Spectroscopy was performed to find the role of cyclic peptides namely curcacycline A (an octapeptide), curcacycline B (a nonapeptide) and curcain (an enzyme) as a possible reducing and stabilizing agents present in the latex of J. curcas L. The average size of ZnS nanoparticles was found to be 10 nm. Latex of J. curcas L. itself acts as a source of sulphide (S −2 ) ions that are donated to Zn ions under present experimental conditions. Source of sulphide (S −2 ) ions is still unclear, but we speculate that cysteine or thiol residues present in enzyme curcain may be donating these sulphide (S −2 ) ions.

Latex glove sensitivity amongst diagnostic imaging healthcare ...

African Journals Online (AJOL)

kemrilib

Sciences, Faculty of Health Sciences and Technology, University of Nigeria, Enugu Campus, Enugu. State, Nigeria. .... Occupation. No of .... latex protein residue and act as a hapten or .... at Work Act, 1989 and the safety, Health and Welfare at.

Incidence of latex harvesting technologies on agronomic and ...

African Journals Online (AJOL)

Incidence of latex harvesting technologies on agronomic and physiological parameters and profitability of some rapid metabolic class clones of rubber tree ( Hevea brasiliensis ) in southwestern Côte d'Ivoire.

Radiation prevulcanized natural rubber latex: Cytotoxicity and safety evaluation on animal

Energy Technology Data Exchange (ETDEWEB)

Keong, C C; Zin, W M Wan; Ibrahim, P; Ibrahim, S, E-mail: chai@nuclearmalaysia.gov.my [Malaysian Nuclear Agency, Bangi, 43000 Kajang, Selangor (Malaysia)

2010-05-15

Radiation prevulcanized natural rubber latex (RVNRL) was claimed to be more user friendly than natural rubber latex prevulcanized by sulphur curing system. The absence of Type IV allergy inducing chemicals in RVNRL make it a suitable material for manufacturing of many kinds of latex products, especially those come into direct contact with users. This paper reveals and discusses the findings of cytotoxicity test and safety evaluation on animal for RVNRL. The test was done on RVNRL films prepared by coagulant dipping method and RVNRL dipped products produced by latex dipped product manufacturers. Cytotocixity test was carried out on mammalian cell culture American Type Culture Collection CCL 81, Vero. Results indicated that no cytotoxic effect from RVNRL films and products was found on the cell culture. Two animal studies, namely dermal sensitization study and primary skin irritation study, were done on gloves made from RVNRL. Albino white guinea pigs were used as test subjects in dermal sensitization study and results showed no sensitization induced by the application of test material in the guinea pigs. Primary skin irritation study was done on New Zealand white rabbits and results showed that the product tested was not corrosive and was not a primary irritant

Radiation prevulcanized natural rubber latex: Cytotoxicity and safety evaluation on animal

International Nuclear Information System (INIS)

Keong, C C; Zin, W M Wan; Ibrahim, P; Ibrahim, S

2010-01-01

Radiation prevulcanized natural rubber latex (RVNRL) was claimed to be more user friendly than natural rubber latex prevulcanized by sulphur curing system. The absence of Type IV allergy inducing chemicals in RVNRL make it a suitable material for manufacturing of many kinds of latex products, especially those come into direct contact with users. This paper reveals and discusses the findings of cytotoxicity test and safety evaluation on animal for RVNRL. The test was done on RVNRL films prepared by coagulant dipping method and RVNRL dipped products produced by latex dipped product manufacturers. Cytotocixity test was carried out on mammalian cell culture American Type Culture Collection CCL 81, Vero. Results indicated that no cytotoxic effect from RVNRL films and products was found on the cell culture. Two animal studies, namely dermal sensitization study and primary skin irritation study, were done on gloves made from RVNRL. Albino white guinea pigs were used as test subjects in dermal sensitization study and results showed no sensitization induced by the application of test material in the guinea pigs. Primary skin irritation study was done on New Zealand white rabbits and results showed that the product tested was not corrosive and was not a primary irritant

Latex content and biomass increase in Mycorrhizal guayule (Parthenium argentatum) under field conditions

Energy Technology Data Exchange (ETDEWEB)

Bloss, H.E.; Pfeiffer, C.M.

1984-01-01

Guayule seedlings were inoculated with two Glomus species in pasteurised soil and grown in the glasshouse without added fertilizer for 8 weeks prior to transplanting to the field. The survival rate of transplanted guayule seedlings was increased by inoculation with vesicular arbuscular mycorrhizal fungi compared wtih uninoculated controls. Inoculated guayule had greater concentrations of Ca, Fe, Mg and Mn at six months of age, and greater concentrations of Ca, Mg, and Zn at 12 months of age than did uninoculated plants. The latex content of both roots and shoots of guayule was greater in inoculated than in uninoculated guayule plants at 12 and 18 months of age. The resin content remained unchanged between treatments irrespective of sampling date.

Soybean oil in water-borne coatings and latex film formation study by AC impedance

Science.gov (United States)

Jiratumnukul, Nantana

Conventional coalescing agents such as butyl cellosolve, butyl carbitol, and TexanolRTM are widely use in the latex coatings industry to facilitate film formation at ambient temperature. Coalescent aids are composed of solvents with low evaporation rates. After water evaporates, coalescent aids would help soften polymer molecules and form continuous films, then gradually evaporates from the film. Coalescent aids, therefore, are considered as volatile organic compounds (VOC), which are of environmental concern. The main purpose of this research project was to prepare a fatty acid glycol ester from soybean oil and glycol (polyols). The soybean oil glycol ester can be used as a coalescent aid in latex paint formulation. The soybean oil glycol ester not only lowered the minimum film formation temperature of latex polymers and continuous film formed at ambient temperature, but also after it has facilitated film formation, does not substantially evaporate, but becomes part of the film. Soybean oil glycol esters, therefore, can reduce the VOC levels and facilitate film formation of latex paints. In the second part of this research AC-Impedance was used to investigate the efficiency of soybean oil coalescent aid in latex film formation relative to the conventional ones. The coating resistance showed that the efficiency of film formation was increased as a function of dry time. The coating resistance also exhibited the effect of soybean oil ester in latex film formation in the same fashion as a conventional coalescent aid, TexanolRTM.

Concentrations of prioritized pharmaceuticals in effluents from 50 large wastewater treatment plants in the US and implications for risk estimation

Science.gov (United States)

We measured the concentrations of 56 active pharmaceutical ingredients (APIs) and seven metabolites, including 50 prioritized APIs, in 24-hour composite effluent samples collected from 50 very large municipal wastewater treatment plants across the US. Hydrochlorothiazide was foun...

Antibiotics in Wastewater of a Rural and an Urban Hospital before and after Wastewater Treatment, and the Relationship with Antibiotic Use—A One Year Study from Vietnam

Directory of Open Access Journals (Sweden)

La Thi Quynh Lien

2016-06-01

Full Text Available Hospital effluents represent an important source for the release of antibiotics and antibiotic resistant bacteria into the environment. This study aims to determine concentrations of various antibiotics in wastewater before and after wastewater treatment in a rural hospital (60 km from the center of Hanoi and in an urban hospital (in the center of Hanoi in Vietnam, and it aims to explore the relationship between antibiotic concentrations in wastewater before wastewater treatment and quantities of antibiotics used in the rural hospital, over a period of one year in 2013. Water samples were collected using continuous sampling for 24 h in the last week of every month. The data on quantities of antibiotics delivered to all inpatient wards were collected from the Pharmacy department in the rural hospital. Solid-phase extraction and high performance liquid chromatography-tandem mass spectrometry were used for chemical analysis. Significant concentrations of antibiotics were present in the wastewater both before and after wastewater treatment of both the rural and the urban hospital. Ciprofloxacin was detected at the highest concentrations in the rural hospital’s wastewater (before treatment: mean = 42.8 µg/L; after treatment: mean = 21.5 µg/L. Metronidazole was detected at the highest concentrations in the urban hospital’s wastewater (before treatment: mean = 36.5 µg/L; after treatment: mean = 14.8 µg/L. A significant correlation between antibiotic concentrations in wastewater before treatment and quantities of antibiotics used in the rural hospital was found for ciprofloxacin (r = 0.78; p = 0.01 and metronidazole (r = 0.99; p < 0.001.

Antibiotics in Wastewater of a Rural and an Urban Hospital before and after Wastewater Treatment, and the Relationship with Antibiotic Use—A One Year Study from Vietnam

Science.gov (United States)

Lien, La Thi Quynh; Hoa, Nguyen Quynh; Chuc, Nguyen Thi Kim; Thoa, Nguyen Thi Minh; Phuc, Ho Dang; Diwan, Vishal; Dat, Nguyen Thanh; Tamhankar, Ashok J.; Lundborg, Cecilia Stålsby

2016-01-01

Hospital effluents represent an important source for the release of antibiotics and antibiotic resistant bacteria into the environment. This study aims to determine concentrations of various antibiotics in wastewater before and after wastewater treatment in a rural hospital (60 km from the center of Hanoi) and in an urban hospital (in the center of Hanoi) in Vietnam, and it aims to explore the relationship between antibiotic concentrations in wastewater before wastewater treatment and quantities of antibiotics used in the rural hospital, over a period of one year in 2013. Water samples were collected using continuous sampling for 24 h in the last week of every month. The data on quantities of antibiotics delivered to all inpatient wards were collected from the Pharmacy department in the rural hospital. Solid-phase extraction and high performance liquid chromatography-tandem mass spectrometry were used for chemical analysis. Significant concentrations of antibiotics were present in the wastewater both before and after wastewater treatment of both the rural and the urban hospital. Ciprofloxacin was detected at the highest concentrations in the rural hospital’s wastewater (before treatment: mean = 42.8 µg/L; after treatment: mean = 21.5 µg/L). Metronidazole was detected at the highest concentrations in the urban hospital’s wastewater (before treatment: mean = 36.5 µg/L; after treatment: mean = 14.8 µg/L). A significant correlation between antibiotic concentrations in wastewater before treatment and quantities of antibiotics used in the rural hospital was found for ciprofloxacin (r = 0.78; p = 0.01) and metronidazole (r = 0.99; p < 0.001). PMID:27314366

Phytochemical characterization, antimicrobial activity and reducing potential of seed oil, latex, machine oil and presscake of Jatropha curcas.

Science.gov (United States)

Sharma, Amit Kumar; Gangwar, Mayank; Kumar, Dharmendra; Nath, Gopal; Kumar Sinha, Akhoury Sudhir; Tripathi, Yamini Bhushan

2016-01-01

This study aims to evaluate the antimicrobial activity, phytochemical studies and thin layer chromatography analysis of machine oil, hexane extract of seed oil and methanol extract of presscake & latex of Jatropha curcas Linn (family Euphorbiaceae). J. curcas extracts were subjected to preliminary qualitative phytochemical screening to detect the major phytochemicals followed by its reducing power and content of phenol and flavonoids in different fractions. Thin layer chromatography was also performed using different solvent systems for the analysis of a number of constituents in the plant extracts. Antimicrobial activity was evaluated by the disc diffusion method, while the minimum inhibitory concentration, minimum bactericidal concentration and minimum fungicidal concentration were calculated by micro dilution method. The methanolic fraction of latex and cake exhibited marked antifungal and antibacterial activities against Gram-positive and Gram-negative bacteria. Phytochemical analysis revealed the presence of alkaloids, saponins, tannins, terpenoids, steroids, glycosides, phenols and flavonoids. Reducing power showed dose dependent increase in concentration compared to standard Quercetin. Furthermore, this study recommended the isolation and separation of bioactive compounds responsible for the antibacterial activity which would be done by using different chromatographic methods such as high-performance liquid chromatography (HPLC), GC-MS etc. The results of the above study suggest that all parts of the plants possess potent antibacterial activity. Hence, it is important to isolate the active principles for further testing of antimicrobial and other biological efficacy.

Test trial radiation vulcanization of natural rubber latex in Jakarta Indonesia

International Nuclear Information System (INIS)

Devendra, R.; Kulatunge, S.S.; Chandralal, H.N.K.K.; Kalyani, N.M.V.; Seneviratne, J.; Wellage, S.

1994-01-01

Radiation vulcanization of natural rubber latex (RVNRL) can be used to make large quantities of specially stabilized latex. It is possible to obtain RVNRL films of tensile strength over 25 MPa. The films could be either coagulant dipped or cast. It is very important to determine the correct radiation dose which gives the maximum tensile strength. Cross linking density or prevulcanized relax modulus (PRM) at 100% is a reliable property to control the prevulcanization

Occurrence of antibiotics in pharmaceutical industrial wastewater, wastewater treatment plant and sea waters in Tunisia.

Science.gov (United States)

Tahrani, Leyla; Van Loco, Joris; Ben Mansour, Hedi; Reyns, Tim

2016-04-01

Antibiotics are among the most commonly used group of pharmaceuticals in human medicine. They can therefore reach surface and groundwater bodies through different routes, such as wastewater treatment plant effluents, surface runoff, or infiltration of water used for agricultural purposes. It is well known that antibiotics pose a significant risk to environmental and human health, even at low concentrations. The aim of the present study was to evaluate the presence of aminoglycosides and phenicol antibiotics in municipal wastewaters, sea water and pharmaceutical effluents in Tunisia. All analysed water samples contained detectable levels of aminoglycoside and phenicol antibiotics. The highest concentrations in wastewater influents were observed for neomycin and kanamycin B (16.4 ng mL(-1) and 7.5 ng mL(-1), respectively). Chloramphenicol was found in wastewater influents up to 3 ng mL(-1). It was observed that the waste water treatment plants were not efficient in completely removing these antibiotics. Chloramphenicol and florfenicol were found in sea water samples near aquaculture sites at levels up to, respectively, 15.6 ng mL(-1) and 18.4 ng mL(-1). Also aminoglycoside antibiotics were found near aquaculture sites with the highest concentration of 3.4 ng mL(-1) for streptomycin. In pharmaceutical effluents, only gentamycin was found at concentrations up to 19 ng mL(-1) over a sampling period of four months.

Use of micrometric latex beads to improve the porosity of hydroxyapatite obtained by chemical coprecipitation method

Science.gov (United States)

Webler, G. D.; Rodrigues, W. C.; Silva, A. E. S.; Silva, A. O. S.; Fonseca, E. J. S.; Degenhardt, M. F. S.; Oliveira, C. L. P.; Otubo, L.; Barros Filho, D. A.

2018-04-01

Hydroxyapatite is one of the most important biomaterials whose application mainly extends to implants and drug delivery. This work will discuss the changes in the pore size distribution of hydroxyapatite when there are latex beads present during the synthesis. These changes were monitored using different techniques: small angle X-ray scattering, X-ray diffraction, thermal gravimetrical analysis, N2 adsorption, scanning and transmission electron microscopy. Latex beads and hydroxyapatite form a single nanocomposite with well-distinguished inorganic and organic phases. Latex bead removal in the temperature range of 300-600 °C did not modify the original crystalline structure of hydroxyapatite. However, the latex beads favored an increase in the adsorption capacity of mesopores at temperatures higher than their glassy transition (Tg). The main result of this research work consists on the increase of surface area and pore size distribution obtained after the removal of latex beads template. Latex beads have been used in a different approach changing the porosity of hydroxyapatite scaffolds not only introducing new routes for cell integration but also broadening the pore size distribution which can result in a more high efficiency for drug release in living cells.

Concentrations of prioritized pharmaceuticals in effluents from 50 large wastewater treatment plants in the US and implications for risk estimation

International Nuclear Information System (INIS)

Kostich, Mitchell S.; Batt, Angela L.; Lazorchak, James M.

2014-01-01

We measured concentrations of 56 active pharmaceutical ingredients (APIs) in effluent samples from 50 large wastewater treatment plants across the US. Hydrochlorothiazide was found in every sample. Metoprolol, atenolol, and carbamazepine were found in over 90% of the samples. Valsartan had the highest concentration (5300 ng/L), and also had the highest average concentration (1600 ng/L) across all 50 samples. Estimates of potential risks to healthy human adults were greatest for six anti-hypertensive APIs (lisinopril, hydrochlorothiazide, valsartan, atenolol, enalaprilat, and metoprolol), but nevertheless suggest risks of exposure to individual APIs as well as their mixtures are generally very low. Estimates of potential risks to aquatic life were also low for most APIs, but suggest more detailed study of potential ecological impacts from four analytes (sertraline, propranolol, desmethylsertraline, and valsartan). -- Highlights: • Report concentrations of 56 pharmaceuticals in effluents from 50 wastewater plants. • Model and measurements agree that potential risks to healthy adult humans are low. • Model and measurements agree some uncertainties remain about risks to aquatic life. -- Measurements of pharmaceuticals in municipal effluent suggest risks of exposure to healthy human adults are low, but suggest the need for study of potential impacts on aquatic life

Production Of Hollow Toy Product From Radiation Pre vulcanized Natural Rubber Latex (RVNRL) By Using Casting And Moulding Technique

International Nuclear Information System (INIS)

Mohd Noorwadi Mat Lazim; Sofian Ibrahim; Muhammad Saiful Omar

2013-01-01

Hollow toy products are very synonym to the child from the age of months since it able to stimulating each of their sense such as sight, hearing, taste, touch and smell. Most of hollow toy products are made from natural rubber latex by using moulding and casting technique. The moulding and casting technique is a manufacturing process by pored liquid latex into a mould, which contain cavity of the desired shape. The mould made from plaster of Paris able to absorbs water from latex meanwhile the presence of calcium ions from plaster of Paris will tend to diffuse into latex thus promote formation of deposit on surface of cavity mould. To improve the quality and safety of hollow toy product made from latex, Radiation Pre vulcanized Natural Rubber Latex (RVNRL) has been identified to be used because it can fulfill the standard requirement for latex and also due to its special abilities such as lower modulus (soft latex products), nitrosamines free, low in nitrosatables, free from chemical accelerators induced allergies and better biodegradability. This paper identify the problem appears from the process of making hollow toy products from RVNRL by using moulding and casting technique. (author)

Biodegradability and aging study of rubber films obtained by gamma radiation vulcanization processes of latex; Estudo da biodegradabilidade e envelhecimento de filmes de borracha obtidos por processos de vulcanizacao do latex por radiacao induzida de fonte gama

Energy Technology Data Exchange (ETDEWEB)

Martins, Carlos Felipe Pinto

2005-07-01

The natural rubber latex (NRL) is industrially crosslinked by the conventional process of vulcanization, which uses sulphur and heat. Otherwise, the network can also be done by the alternative process with ionizing radiation. In this work the crosslinking of NRL was studied by the comparison of the conventional vulcanization system and the ionizing radiation process of {sup 60}C source. The products obtained, the irradiated latex, the irradiated latex with approximately 1% of soy lecithin and the sulphur vulcanized latex were tested by accelerated aging with ultraviolet (UV) and outdoor aging with compostage, tensile strength at break, swelling and gel fraction, fungi micro biota, scanning electron microscopy (SEM), infrared spectroscopy (FTIR) and thermogravimetry and differential scanning calorimetry analysis (TG and DSC). The results showed that the aging with microorganisms have a great influence in the physical properties of the samples. The thermal stability order observed showed that the sulphur vulcanized latex is more resistant, what is probably associated to a network more stable under the aging conditions. On the other hand, the irradiated latex showed intense biodegradation aspects, particularly with the presence of the soy lecithin. (author)

Rubber/clay nanocomposites by combined latex compounding and melt mixing: A masterbatch process

International Nuclear Information System (INIS)

Tan, Jinghua; Wang, Xiaoping; Luo, Yuanfang; Jia, Demin

2012-01-01

Highlights: → Rubber/Ca-montmorillonite nanocomposites were prepared by the masterbatch process. → Latex compounding method is efficient to improve the Ca-montmorillonite dispersion. → Exfoliated structure was obtained in the masterbatch by latex compounding method. → Intercalated and exfoliated structures were achieved in the vulcanizate. → The properties of vulcanizate are improved by the addition of Ca-montmorillonite. -- Abstract: Rubber/Ca-montmorillonite (Ca-MMT) nanocomposites with well exfoliated Ca-MMT layers were prepared by combination of latex compounding and melt mixing. Firstly, a high Ca-MMT content masterbatch was co-coagulated by natural rubber (NR) latex and modified Ca-MMT aqueous suspension through latex compounding. The masterbatch was added in the system of styrene butadiene rubber (SBR) and epoxidized natural rubber (ENR) by melt mixing subsequently. The X-ray diffraction (XRD) and transmission electronic microscopy (TEM) results showed that intercalated and exfoliated nanocomposites were obtained by the masterbatch technique. The effects of modified Ca-MMT introduction into the rubber matrix, via the masterbatch technique, on the properties of the resulting composites were studied. It was found that the vulcanization was hindered by the incorporation of modified Ca-MMT, while mechanical performances, thermal stability and aging resistance were improved. The increasingly glass transition temperature and the storage modulus with the loading of modified Ca-MMT were measured by dynamic mechanical analysis (DMA).

Diagnosis of toxoplasmosis in pregnancy. Evaluation of latex-protein complexes by immnunoagglutination.

Science.gov (United States)

Peretti, Leandro E; Gonzalez, Verónica D G; Marcipar, Iván S; Gugliotta, Luis M

2017-07-01

The aim of this work was to obtain a reagent based on latex particles for ruling out acute toxoplasmosis in pregnant women by immunoagglutination (IA). Latex-protein complexes (LPC) were previously synthesized coupling the recombinant protein of Toxoplasma gondii P22Ag and the homogenate of the parasite to latex particles with different size, chemical functionality and charge density. LPC were tested in IA assays against a panel of 72 pregnant women serum samples. Results were analysed through receiver operating characteristic curves, determining area under the curve (AUC), sensitivity, specificity positive and negative predictive values (PPV and NPV, respectively). It was observed that the antigenicity of proteins was not affected during sensitization by either physical adsorption or covalent coupling. The best results in the sense of maximizing discrimination of low avidity sera from chronic ones were observed for the IA test based on latex particles with carboxyl functionality and the recombinant P22Ag, obtaining an AUC of 0·94, a sensitivity of 100% and a NPV of 100%. In this way, the proposed test could be useful for the toxoplasmosis diagnosis in pregnant women, with the advantages of being cheap, rapid and easy to be implemented.

Optimization of the Ethanol Fermentation of Cassava Wastewater ...

African Journals Online (AJOL)

This research work focused on the optimisation of the cassava wastewater medium for ethanol fermentation. The main thrust was the investigation of the influence of the glucose concentration, nutrient (NH4Cl) level, and cell concentration on the yield of ethanol from cassava wastewater. Twenty experiments based on ...

Towards anti-corrosion coatings from surfactant-free latexes based on maleic anhydride containing polymers

NARCIS (Netherlands)

Soer, W.J.; Ming, W.; Koning, C.E.; Benthem, van R.A.T.M.

2008-01-01

We report on the film formation of surfactant-free, artificial latexes based on copolymers containing maleic anhydride. Different metallic substrates, such as aluminum, steel and magnesium alloys, were coated with three different latexes. A commercial polyester based coating was used as a

Latex allergy and occupational asthma in health care workers: adverse outcomes.

OpenAIRE

Amr, Sania; Bollinger, Mary E.

2004-01-01

The prevalence of natural rubber latex (NRL) allergy has been estimated to be 5-18% in health care workers, and latex exposure has been one of the leading causes of occupational asthma in the last several years. We present the cases of two nurses who developed sensitivity to NRL, both with dermatologic symptoms and respiratory symptoms that included asthma. They were referred to the University of Maryland for evaluation of their allergies, then for occupational and environmental consults. The...

Radiation graft copolymerization of n-butyl acrylate on natural rubber latex

International Nuclear Information System (INIS)

Sundardi, F.; Kadariah, S.

1986-01-01

A method of radiation graft copolymerization of n-butyl acrylate (NBA) on natural rubber (NR) latex has been studied. The rate of conversion increases with the increase of NBA in latex. An irradiation dose of about 12 kGy is needed to obtain 90% conversion with 40 phr of NBA in latex. Tensile strength, tear strength, and elongation at break of grafted NR are found to decrease with increasing degree of grafting. The physical strength of a vulcanizate prepared from a mixture of NR and ply-NBA was found to be better than that of NBA-NR graft copolymer vulcanizate. The graft copolymerization reaction takes place in the outer layer of NR particles, and because the secondary bonds between poly-NBA molecules may be weaker than those between NR molecules, the existence of a poly-NBA layer in NR particles will decrease its physical strength

Synergetic effect of copper-plating wastewater as a catalyst for the destruction of acrylonitrile wastewater in supercritical water oxidation

Energy Technology Data Exchange (ETDEWEB)

Shin, Young Ho; Lee, Hong-shik; Lee, Young-Ho [School of Chemical and Biological Engineering and Institute of Chemical Processes, Seoul National University, 599 Gwanangno, Gwanak-gu, Seoul 151-744 (Korea, Republic of); Kim, Jaehoon; Kim, Jae-Duck [Supercritical Fluid Research Laboratory, Energy and Environment Research Division, Korea Institute of Science and Technology (KIST), 39-1 Hawolgok-dong, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Lee, Youn-Woo, E-mail: ywlee@snu.ac.kr [School of Chemical and Biological Engineering and Institute of Chemical Processes, Seoul National University, 599 Gwanangno, Gwanak-gu, Seoul 151-744 (Korea, Republic of)

2009-08-15

A new supercritical water oxidation process for the simultaneous treatment of mixed wastewater containing wastewater from acrylonitrile manufacturing processes and copper-plating processes was investigated using a continuous tubular reactor system. Experiments were carried out at temperatures ranging from 400 to 600 deg. C and a pressure of 25 MPa. The residence time was fixed at 2 s by changing the flow rates of feeds, depending on reaction temperature. The initial total organic carbon (TOC) concentration of the wastewaters and the O{sub 2} concentration at the reactor inlet were kept constant at 0.49 and 0.74 mol/L. It was confirmed that the copper-plating wastewater accelerated the TOC conversion of acrylonitrile wastewater from 17.6% to 67.3% at a temperature of 450 deg. C. Moreover, copper and copper oxide nanoparticles were generated in the process of supercritical water oxidation (SCWO) of mixed wastewater. 99.8% of copper in mixed wastewater was recovered as solid copper and copper oxides at a temperature of 600 deg. C, with their average sizes ranging from 150 to 160 nm. Our study showed that SCWO provides a synergetic effect for simultaneous treatment of acrylonitrile and copper-plating wastewater. During the reaction, the oxidation rate of acrylonitrile wastewater was enhanced due to the in situ formation of nano-catalysts of copper and/or copper oxides, while the exothermic decomposition of acrylonitrile wastewater supplied enough heat for the recovery of solid copper and copper oxides from copper-plating wastewater. The synergetic effect of wastewater treatment by the newly proposed SCWO process leads to full TOC conversion, color removal, detoxification, and odor elimination, as well as full recovery of copper.

Effects of returning NF concentrate on the MBR-NF process treating antibiotic production wastewater.

Science.gov (United States)

Li, Kun; Cheng, Yutao; Wang, Jianxing; Zhang, Junya; Liu, Jibao; Yu, Dawei; Li, Mingyue; Wei, Yuansong

2016-07-01

The optimization of the nanofiltration (NF) concentrate backflow ratio (R cb) and the influence of the NF concentrate on the performance of membrane bioreactor-nanofiltration (MBR-NF) process treating antibiotic production wastewater were investigated on a laboratory scale. The R cb was optimized at 60 % based on the removal rates of chemical oxygen demand (COD) and NH4 (+)-N by MBR. Data analyses indicated that salinity brought by NF concentrate is the major driver leading to the decrease of sludge activity, especially at a high R cb. EPS analysis showed that electric conductivity (EC), proteins in soluble microbial products (SMP), and SMP brought by NF concentrate are the dominant factors causing the severe membrane fouling in MBR. Furthermore, undegradable substances including fulvic acid-like and humic acid-like compounds accumulated in NF concentrate showed significant influence on fouling of NF. MBR could well degrade small MW compounds in NF concentrate, which confirmed the enhancement of organic removal efficiency by recycling the NF concentrate to MBR. The MBR-NF process showed a relatively stable performance at the R cb of 60 % (volume reduction factor (VRF) = 5), and the NF permeate could satisfy the water quality standard for fermentation process with a water recovery rate of 90.9 %.

Control of Sewer systems and Wastewater treatment plants using pollutant concentration profiles

DEFF Research Database (Denmark)

Bechmann, Henrik; Nielsen, Marinus K.; Madsen, Henrik

1998-01-01

On-line measurements of pollutants in the wastewater combined with grey-box modelling are used to estimate the amount of deposits in the sewer system. The pollutant mass flow at the wastewater treatment plant is found to consist of a diurnal profile minus the deposited amount of pollutants...

Effect of salt type and concentration on the growth and lipid content of Chlorella vulgaris in synthetic saline wastewater for biofuel production.

Science.gov (United States)

Church, Jared; Hwang, Jae-Hoon; Kim, Keug-Tae; McLean, Rebecca; Oh, You-Kwan; Nam, Bora; Joo, Jin Chul; Lee, Woo Hyoung

2017-11-01

Microalgae can offer several benefits for wastewater treatment with their ability to produce large amounts of lipids for biofuel production and the high economic value of harvested biomass for biogas and fertilizer. This study found that salt concentration (∼45gL -1 ) had more of an effect than salt type on metabolisms of Chlorella vulgaris for wastewater treatment and biofuel production. Salinity stress decreased the algal growth rate in wastewater by 0.003day -1 permScm -1 and slightly reduced nutrient removal rates. However, salinity stress was shown to increase total lipid content from 11.5% to 16.1% while also increasing the saturated portions of fatty acids in C. vulgaris. In addition, salinity increased the algal settling rate from 0.06 to 0.11mday -1 which could potentially reduce the cost of harvesting for algal biofuel production. Overall, C. vulgaris makes a suitable candidate for high salinity wastewater cultivation and biofuel production. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effects of oil sands wastewater on fish resulting from exposure to sub-lethal concentrations

International Nuclear Information System (INIS)

Birkholz, D.A.; Goudey, J.S.; Balch, G.C.; Nelson, L.R.; MacKinnon, M.

1995-01-01

Rainbow trout, Oncorhynchus mykiss, were exposed to sub-lethal concentrations of oil sands wastewater in flow through laboratory experiments as well as to artificial ponds containing sub-lethal concentrations of tailings pond water and fine tails in order to study the viability of the wet landscape remediation option. Large (200--300 g) fish were used for all the exposures in this preliminary study and the following data were collected: blood cell counts, sex hormone concentrations, sexual maturation, stress protein concentrations, PAH-metabolites in bile, condition factors, liver somatic indices, mixed function oxygenase induction, PAHs in muscle, external condition and the condition of internal organs. The data obtained from this study revealed no adverse effects upon fish during extended field exposures. Given similar exposure conditions in the release waters of a wet landscape reclamation, the data suggest that there may be no adverse effects upon fish, however, longer term studies, other indicator organisms and additional chronic tests should be conducted

Evaluation of peptides release using a natural rubber latex biomembrane as a carrier.

Science.gov (United States)

Miranda, M C R; Borges, F A; Barros, N R; Santos Filho, N A; Mendonça, R J; Herculano, R D; Cilli, E M

2018-05-01

The biomembrane natural (NRL-Natural Rubber Latex), manipulated from the latex obtained from the rubber tree Hevea brasiliensis, has shown great potential for application in biomedicine and biomaterials. Reflecting the biocompatibility and low bounce rate of this material, NRL has been used as a physical barrier to infectious agents and for the controlled release of drugs and extracts. The aim of the present study was to evaluate the incorporation and release of peptides using a latex biomembrane carrier. After incorporation, the release of material from the membrane was observed using spectrophotometry. Analyses using HPLC and mass spectroscopy did not confirm the release of the antimicrobial peptide [W 6 ]Hylin a1 after 24 h. In addition, analysis of the release solution showed new compounds, indicating the degradation of the peptide by enzymes contained in the latex. Additionally, the release of a peptide with a shorter sequence (Ac-WAAAA) was evaluated, and degradation was not observed. These results showed that the use of NRL as solid matrices as delivery systems of peptide are sequence dependent and could to be evaluated for each sequence.

Frequent IgE sensitization to latex, cow's milk, and egg in children with short bowel syndrome.

Science.gov (United States)

Mazon, Angel; Solera, Eva; Alentado, Noemi; Oliver, Fernando; Pamies, Rafael; Caballero, Luis; Nieto, Antonio; Dalmau, Jaime

2008-03-01

Children with short bowel syndrome (SBS) undergo frequent operations, so they are at risk for sensitizing to latex. There have been isolated reports of sensitization to food in these children. In a cross-sectional study, we assessed sensitization to latex, cow's milk, and egg with skin prick tests (SPT) and serum-specific immunoglobulin E (IgE) in 14 children with SBS. Data were collected about the number of operations with latex devices, serum total IgE, and history of feeding with milk formula. Ten children were sensitized to latex (specific IgE median: 6.7 kU/l, range: 0.5-33). Compared with those non-sensitized, sensitized children had significantly (p range: 0.5-21.1 kU/l), and five to egg (specific IgE median: 0.68, range: 0.58-2.17 kU/l). Except for some isolated days with cow's milk formula, the children had been initially fed with a diet without intact cow's milk proteins. Sensitization to latex, cow's milk, and egg is very frequent in children with SBS. They should be treated in a latex-free environment since the very early stages of the disease, and should be routinely studied regarding food sensitization, as this might contribute as an added factor in the chronic diarrhea of these patients.

The influence of the microbial quality of wastewater, lettuce cultivars and enumeration technique when estimating the microbial contamination of wastewater-irrigated lettuce.

Science.gov (United States)

Makkaew, P; Miller, M; Cromar, N J; Fallowfield, H J

2017-04-01

This study investigated the volume of wastewater retained on the surface of three different varieties of lettuce, Iceberg, Cos, and Oak leaf, following submersion in wastewater of different microbial qualities (10, 10 2 , 10 3 , and 10 4 E. coli MPN/100 mL) as a surrogate method for estimation of contamination of spray-irrigated lettuce. Uniquely, Escherichia coli was enumerated, after submersion, on both the outer and inner leaves and in a composite sample of lettuce. E. coli were enumerated using two techniques. Firstly, from samples of leaves - the direct method. Secondly, using an indirect method, where the E. coli concentrations were estimated from the volume of wastewater retained by the lettuce and the E. coli concentration of the wastewater. The results showed that different varieties of lettuce retained significantly different volumes of wastewater (p 0.01) were detected between E. coli counts obtained from different parts of lettuce, nor between the direct and indirect enumeration methods. Statistically significant linear relationships were derived relating the E. coli concentration of the wastewater in which the lettuces were submerged to the subsequent E. coli count on each variety the lettuce.

The evolution and use of a personal LaTeX metapackage

DEFF Research Database (Denmark)

Andersen, Esben Sloth

This document defines and describes esameta.sty and its variant esametaps.sty. They are personal LATEX packages that largely consist of calls of other packages. These 'metapackages' are selected to help the development of the author's complex book and paper projects-but some of his decisions migh...... be of more general relevance. The use of the LATEX system of 'literate programming' and the testing the compatibility of new commands and packages with the previously included parts of the metapackage should also be noticed....

Residual monomer reduction in polymer latex products by extraction with supercritical carbon dioxide

NARCIS (Netherlands)

Aerts, M.; Meuldijk, J.; Kemmere, M.F.; Keurentjes, J.T.F.

2011-01-01

Extraction of residual monomer from a latex product with supercritical carbon dioxide ((sc)CO2) in a column was studied. Operating conditions were chosen at 35¿°C and 100 bar. For reducing the residual styrene level in a polystyrene latex from 104 ppm to 100¿ppm and from 104 ppm to 10¿ppm, a

Incidence of latex harvesting technologies on agronomic and ...

African Journals Online (AJOL)

parameters and profitability of some rapid metabolic class clones of rubber ... of hormonal stimulation had no negative influence on the vegetative growth ..... yield (2597) was obtained with the control ..... metabolic energy of latex vessels as.

Changes in chemical permeation of disposable latex, nitrile, and vinyl gloves exposed to simulated movement.

Science.gov (United States)

Phalen, Robert N; Le, Thi; Wong, Weng Kee

2014-01-01

Glove movement can affect chemical permeation of organic compounds through polymer glove products. However, conflicting reports make it difficult to compare the effects of movement on chemical permeation through commonly available glove types. The aim of this study was to evaluate the effect of movement on chemical permeation of an organic solvent through disposable latex, nitrile, and vinyl gloves. Simulated whole-glove permeation testing was conducted using ethyl alcohol and a previously designed permeation test system. With exposure to movement, a significant decrease (p ≤ 0.001) in breakthrough time (BT) was observed for the latex (-23%) and nitrile gloves (-31%). With exposure to movement, only the nitrile glove exhibited a significant increase (p ≤ 0.001) in steady-state permeation rate (+47%) and cumulative permeation at 30 min (+111%). Even though the nitrile glove provided optimum chemical resistance against ethyl alcohol, it was most affected by movement. With exposure to movement, the latex glove was an equivalent option for overall worker protection, because it was less affected by movement and the permeation rate was lower than that of the nitrile glove. In contrast, the vinyl glove was the least affected by movement, but did not provide adequate chemical resistance to ethyl alcohol in comparison with the nitrile and latex gloves. Glove selection should take movement and polymer type into account. Some glove polymer types are less affected by movement, most notably the latex glove in this test. With nitrile gloves, at least a factor of three should be used when attempting to assign a protection factor when repetitive hand motions are anticipated. Ultimately, the latex gloves outperformed nitrile and vinyl in these tests, which evaluated the effect of movement on chemical permeation. Future research should aim to resolve some of the observed discrepancies in test results with latex and vinyl gloves.

Prevalence of manufacturing defects in latex examination gloves used in selected dental practices in central Saudi Arabia.

Science.gov (United States)

Al-Swuailem, Abdullah S

2014-07-01

To assess the defect rates in latex examination gloves used in selected dental practices in Riyadh, Saudi Arabia. In this cross-sectional study, a total of 796 latex examination gloves were collected from 5 governmental hospitals and 5 private dental practices between April 2012 and May 2012. The gloves were assessed for presence of defects visually (VT) and using water inflation test (WIT). One and 2 sample t-tests were used to assess significant differences in defect rates among each latex brand, and between governmental hospitals and private dental practices. Defects in latex gloves were more likely to be identified using WIT compared with VT (20.2% versus 4.3%, p=0.000). Using WIT, examined latex gloves had a defect rate approximately 8 times the acceptable quality level of 2.5% (20.2%, p=0.000). Using WIT, gloves used in private dental practices had significantly higher defect rates compared with governmental dental clinics (25.6% versus 14.6%, p=0.006). Most latex examination gloves used in the sampled governmental dental clinics and private dental practices in Riyadh had significantly higher preexisting defect rates than acceptable standard levels.

Comparative evaluation of Type 1 latex hypersensitivity in patients with chronic urticaria, rubber factory workers and healthy control subjects

NARCIS (Netherlands)

Piskin, Gamze; Akyol, Aynur; Uzar, Hatice; Tulek, Necla; Boyvat, Ayse; Gurgey, Erbak

2003-01-01

Latex hypersensitivity manifests itself most commonly with contact urticaria. In this study, we investigated the frequency of latex hypersensitivity as a possible aetiological factor in patients with chronic urticaria (CU) and compared latex hypersensitivity of CU patients (n = 50) with that of

A study of using polythiol compounds and 2-ethyl-hexyl-acrylate with carbon tetrachloride as sensitizers for radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Polsuksiri, C.

1989-01-01

Experiments on using 3 different compounds of polythiol and an acrylate as sensitizer for radiation vulcanization were conducted. It was found that 1,4 butane diol propane tris-3-mercapto propionate showed the tendency to be a good sensitizer. The tensile strength of the rubber film prepared from the irradiated latex was found to be 14 MPa at sensitizer concentration of 1 phr and radiation dose of 45 kGy. As for 2-ethyl hexyl acrylate (2EHA), the maximum tensile strength of rubber film was found to be 23 MPa at concentration of 3 phr and radiation dose of 35 kGy. The mixture of 2 EHA and CCl 4 at various ratio was also used as sensitizer. The optimum ratio was found to be 5:1 at concentration of 6 phr and radiation dose of 15 kGy. The maximum tensile strength was as high as 25 MPa. The study also revealed that the radiation vulcanized latex with crosslink density of about 18x10 18 C.L./cm 3 would give the rubber film of highest tensile strength

Phytochemical characterization, antimicrobial activity and reducing potential of seed oil, latex, machine oil and presscake of Jatropha curcas

Directory of Open Access Journals (Sweden)

Amit Sharma

2016-06-01

Full Text Available Objective: This study aims to evaluate the antimicrobial activity, phytochemical studies and thin layer chromatography analysis of machine oil, hexane extract of seed oil and methanol extract of presscake& latex of Jatropha curcas Linn (family Euphorbiaceae. Materials and Methods: J. curcas extracts were subjected to preliminary qualitative phytochemical screening to detect the major phytochemicals followed by its reducing power and content of phenol and flavonoids in different fractions. Thin layer chromatography was also performed using different solvent systems for the analysis of a number of constituents in the plant extracts. Antimicrobial activity was evaluated by the disc diffusion method, while the minimum inhibitory concentration, minimum bactericidal concentration and minimum fungicidal concentration were calculated by micro dilution method. Results: The methanolic fraction of latex and cake exhibited marked antifungal and antibacterial activities against Gram-positive and Gram-negative bacteria. Phytochemical analysis revealed the presence of alkaloids, saponins, tannins, terpenoids, steroids, glycosides, phenols and flavonoids. Reducing power showed dose dependent increase in concentration compared to standard Quercetin. Furthermore, this study recommended the isolation and separation of bioactive compounds responsible for the antibacterial activity which would be done by using different chromatographic methods such as high-performance liquid chromatography (HPLC, GC-MS etc. Conclusion: The results of the above study suggest that all parts of the plants possess potent antibacterial activity. Hence, it is important to isolate the active principles for further testing of antimicrobial and other biological efficacy.

Extractable protein of radiation vulcanized natural rubber latex

International Nuclear Information System (INIS)

Soebianto, Y.S.; Upul, R.M.; Makuuchi, K.; Yoshii, F.; Kume, T.

2000-01-01

A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) as much as 3 phr in three different processes: added to RVNRL, added to re-centrifuged RVNRL, and added to RVNRL followed by centrifugation. The protein content was determined by enhanced BCA method, and identified by SDS-PAGE analysis. Addition of WSP followed by centrifugation reduces EP up to the minimum protein detection, and shortens the leaching time to 20-30 min. SDS-PAGE analysis confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The molecular weight of WSP dictates the efficiency of protein removal. (author)

Extractable protein of radiation vulcanized natural rubber latex

Energy Technology Data Exchange (ETDEWEB)

Soebianto, Y.S. [Center for Research and Development of Isotopes and Radiation Technology, BATAN, Jakarta (Indonesia); Upul, R.M. [Rubber Research Institute of Sri Lanka, Ratmalana (Sri Lanka); Makuuchi, K.; Yoshii, F.; Kume, T. [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

2000-03-01

A new method to reduce the protein level in the latex products by irradiation is reported. Water soluble protein (WSP) solution (10%) was added into radiation vulcanized NR latex (RVNRL) as much as 3 phr in three different processes: added to RVNRL, added to re-centrifuged RVNRL, and added to RVNRL followed by centrifugation. The protein content was determined by enhanced BCA method, and identified by SDS-PAGE analysis. Addition of WSP followed by centrifugation reduces EP up to the minimum protein detection, and shortens the leaching time to 20-30 min. SDS-PAGE analysis confirms the reduction of soluble protein in the serum phase, and disappearance of protein bands in the rubber extract. Protein-WSP interaction produces water soluble complex, and removed by centrifugation. The molecular weight of WSP dictates the efficiency of protein removal. (author)

Solubility of mixed monomers of tetrafluoroethylene and propylene in water and latex

International Nuclear Information System (INIS)

Watanabe, Hiromasa; Okamoto, Jiro

1978-03-01

For kinetical analysis of the emulsion copolymerization of tetrafluoroethylene with propylene and selection of the optimum reaction conditions, the monomer concentrations and composition of the polymer particle were measured and the relations with reaction conditions were determined. Solubilities of tetrafluoroethylene and propylene in water increase with pressure. solubility of propylene is larger than that of tetrafluoroethylene. Solubility of the mixed monomers in water and latex increases with pressure and propylene concentration and decreases with temperature. Propylene concentration in the dissolved monomers is dependent on its concentration in the gas phase and independent of pressure and temperature. The monomer concentrations and the composition were estimated from measurements. Under propylene concentration in the gas phase of 0 to 40 wt % at 30 Kg/cm 2 G and 40 0 C, the monomer concentration and propylene fraction of the polymer particle are 17 -- 27% and 0 -- 62% respectively. The amount of propylene in the particle increases with its fraction in the gas phase, but the amount of tetrafluoroethylene is independent of its fraction in the gas phase. Monomer composition of the polymer particle is dependent on monomer composition of the gas phase and independent of temperature and pressure. The concentration in the polymer particle is 17% at propylene concentration 10 mole % in the gas phase. (auth.)

Evaluation of methods using celite to concentrate norovirus, adenovirus and enterovirus from wastewater

Science.gov (United States)

Enteroviruses, noroviruses and adenoviruses are among the most common viruses infecting humans worldwide. These viruses are shed in the feces of infected individuals and can accumulate in wastewater. Therefore, wastewater is a source of a potentially diverse group of enteric viru...

NR based curred latex material reclaimed with 2,2'-dibenzamidodiphenyldisulphide in truck tyre tread compound

NARCIS (Netherlands)

Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

2006-01-01

It is observed that reclamation of natural rubber latex based rubber using 2,2'-dibenzamidodiphenyldisulphide as reclaiming agent is an optional methodology for recycling of waste latex rubber (WLR). For progressive replacement of virgin natural rubber by the reclaim, two alternatives curing system

Latex agglutination test (LAT) for the diagnosis of typhoid fever.

Science.gov (United States)

Sahni, Gopal Shankar

2013-06-01

The efficacy of latex agglutination test in the rapid diagnosis of typhoid fever was studied and the result compared with that of blood culture. This study included 80 children suffering from typhoid fever, among which 40 were confirmed by blood culture isolation and 40 had possible typhoid fever based on high Widal's titre (a four-fold rise in the titre of antibody to typhi "O" and "H" antigen was considered as a positive Widal's test result). Eighty children, 40 with febrile illness confirmed to be other than typhoid and 40 normal healthy children were used as negative controls. The various groups were: (i) Study group ie, group I had 40 children confirmed by culture isolation of Salmonella typhi(confirmed typhoid cases). (ii) Control groups ie, (a) group II with 40 febrile controls selected from paediatrics ward where cause other than S typhi has been established, (b) group III with 40 afebrile healthy controls that were siblings of the children admitted in paediatric ward for any reason with no history of fever and TAB vaccination in the last one year, and (c) group IV with 40 children with high Widal's titre in paired sera sample. Widal's test with paired sera with a one week interval between collections were done in all 40 patients. Latex aggtutination test which could detect 900 ng/ml of antigen as observed in checker board titration, was positive in all 40 children from group I who had positive blood culture and in 30 children from group IV who had culture negative and had high Widal's titre positive. Latex agglutination test was positive in 4 children in group II and none in group III. Using blood culture positive cases as true positive and children in groups II and III as true negative, the test had a sensitivity of 100% and specificity of 96%. Latex agglutination test was found to be significantly sensitive (100%) and specific (96%) and could detect 75% more cases in group IV (possible typhoid cases). Thus latex agglutination test can be used for rapid

Developing on-site paper colorimetric monitoring technique for quick evaluating copper ion concentration in mineral wastewater

Science.gov (United States)

Liu, Guokun; Peng, Jingji; Zheng, Hong; Yuan, Dongxing

2018-05-01

With the reinforce of the copper mining, the on-site monitoring of the accompanied effluent discharge is highly demanded for the emergency response to minimize the negative effect of the effluent on the surrounding ecosystem. On the basis of the specific interaction between Cu2+ and L-Cysteine (L-Cys), which was modified on gold nanoparticles (Au NPs), and the aggregation dependent surface plasmon resonance (SPR) of Au NPs, we developed an easy-on-going paper colorimetric method for the quick evaluating the copper ion concentration in the waste water excreted from the copper mine. The color change of L-Cys modified Au NPs (L-Cys-Au NPs)immobilized on a filter paper was very sensitive to the Cu2+ concentration and free of interference from other metal ions typically in waste water. The proposed paper colorimetry has the LOD of 0.09 mg/L and the linear range of 0.1-10 mg/L, respectively, with the RSD (n = 5) was 6.6% for 1 mg/L Cu2+ and 3.5% for 5 mg/L Cu2+. The quantitative analysis results for the mineral wastewater is in good agreement the China National Environmental Protection Standards HJ485-2009, which indicates the current method could be developed to the on-site detection technique for the emergency response in monitoring Cu2+ in industrial wastewater or polluted water.

Minimizing surgical skin incision scars with a latex surgical glove.

Science.gov (United States)

Han, So-Eun; Ryoo, Suk-Tae; Lim, So Young; Pyon, Jai-Kyung; Bang, Sa-Ik; Oh, Kap-Sung; Mun, Goo-Hyun

2013-04-01

The current trend in minimally invasive surgery is to make a small surgical incision. However, the excessive tensile stress applied by the retractors to the skin surrounding the incision often results in a long wound healing time and extensive scarring. To minimize these types of wound problems, the authors evaluated a simple and cost-effective method to minimize surgical incision scars based on the use of a latex surgical glove. The tunnel-shaped part of a powder-free latex surgical glove was applied to the incision and the dissection plane. It was fixed to the full layer of the dissection plane with sutures. The glove on the skin surface then was sealed with Ioban (3 M Health Care, St. Paul, MN, USA) to prevent movement. The operation proceeded as usual, with the retractor running through the tunnel of the latex glove. It was possible to complete the operation without any disturbance of the visual field by the surgical glove, and the glove was neither torn nor separated by the retractors. The retractors caused traction and friction during the operation, but the extent of damage to the postoperative skin incision margin was remarkably less than when the operation was performed without a glove. This simple and cost-effective method is based on the use of a latex surgical glove to protect the surgical skin incision site and improve the appearance of the postoperative scar. This journal requires that authors assign a level of evidence to each article. For a full description of these Evidence-Based Medicine ratings, please refer to the Table of Contents or the online Instructions to Authors www.springer.com/00266 .

Gamma irradiator design concepts for radiation vulcanisation of natural rubber latex

International Nuclear Information System (INIS)

Aggarwal, K.S.; Muralidharan, P.; Apte, M.G.; Kalurkar, A.R.; Shah, B.M.

1990-01-01

Radiation vulcanisation of natural rubber latex (NRL) is a new and yet unproven technology and one which involves undefined problems of consumer acceptance and high degree of radiation risk. Therefore, the designer should take care that the initial capital cost of the plant is as low as possible to keep the unit processing cost low during the initial lean period of the product requirement by the market. Three irradiators to process natural rubber latex have been designed as per capacity requirement of the user. Their salient features are described. (author). 2 tabs., 24 figs

Status RVNRL in German latex industry and its introduction to the European market

International Nuclear Information System (INIS)

Bez, W.

1996-01-01

Reasons to look for an alternative crosslinking system avoiding sulphur curing was the restrictive policy of the German Health Authorities concerning nitrosamines. It was concluded that radiation curing offers further advantages . By avoiding the accelerators, type IV allergy is excluded, cytotoxicity is minimised to a very low level, films have better clarity and when thoroughly leached higher electrical resistance. Treatment of waste give no SO sub 2 emissions by burning, no Zinc in the ashes and possibly better microbial degradation. A development was carried out to irradiate natural latex by electron beam with a Dynamitron equipment. It was found trimethylolpropanetrimethacrylate to be a suitable sensitizer. Because of to high prices this development was interrupted. For future application trials and efforts to introduce RVNRL in the market gamma ray radiated natural latex either from Batan, Indonesia or MINT, Malaysia are used. Mainly dipped goods were produce, but radiated natural latex has shown good results in other processes. During discussions with customers it has proved necessary to establish specifications for RVNRL. A serious problem using natural latex for the production of medical devices is the type I allergy. Attempts are made to dip surgical gloves, leach them thoroughly and control extractable proteins were reduced to the very low level of 6.5 μg/g. Out of 18 patients sensitive to natural latex protein wearing gloves made from RVNRL only six have shown a positive response. That means RVNRL could help to solve the protein allergy problem. Further developments on this line are scheduled

Prevalence of Allergy to Natural Rubber Latex and Potential Cross Reacting Food in Operation Room Staff in Shiraz Hospitals -2006

OpenAIRE

H Nabavizade; R Amin

2007-01-01

Introduction & Objective: Allergic reactions to natural rubber latex have increased during past 10 years especially among health care workers and patients with high exposure to latex allergens. Allergic reaction to latex is related to many diseases like occupational asthma. This study was performed to determine the prevalence of allergy to natural rubber latex and potential cross reacting food in operation room staff in Shiraz hospitals. Materials & Methods: In this cross-sectional descr...

Purification of papain from fresh latex of Carica papaya

Directory of Open Access Journals (Sweden)

Rubens Monti

2000-01-01

Full Text Available In the present study we wish to report a method of crystallizing papain from fresh papaya latex which gave higher yields than previously reported. This method does not involve the use of sulphydryl reagents. The papain thus obtained is practically pure and shows a single band when submitted to electrophoresis on polyacrylamide gel, and is identical to the papain obtained by other methods. In routine enzymatic assays, specific activity was measured using Z-gly-pNP and BAEE as substrates. Papain crystallized by this method, without the use of high concentrations of salts or thiol-containing substances such as cysteine and dithiothreitol, is obtained in the form of a complex with natural inhibitors existent in latex which can be removed by dialysis.No presente trabalho apresenta-se um método de cristalização da papaína oriunda do látex fresco de mamão, o qual apresenta uma alta produtividade em relação aos métodos previamente descritos. A metodologia aqui descrita não envolve o uso de reagentes sulfidrílicos, a papaína foi obtida de forma praticamente pura, apresentando uma simples banda quando submetida a eletroforese, e com propriedades idênticas àquelas obtidas por outros métodos. A atividade específica foi determinada utilizando Z-gly-pNP e BAEE como substrato. A papaína obtida por essa metodologia, sem uso de substâncias tais como cisteína e ditiotreitol, apresenta-se na forma de um complexo com inibidores naturais, os quais podem ser removidos por diálise.

Analysis of Treated Wastewater Produced from Al-Lajoun Wastewater Treatment Plant, Jordan

Directory of Open Access Journals (Sweden)

Waleed Manasreh

2009-01-01

Full Text Available Assessment of treated wastewater produced from Al-Lajoun collection tanks of the wastewater treatment plant in Karak province was carried out in term of physical properties, its major ionic composition, heavy metals and general organic content, for both wastewater influent and effluent. Sampling was done in two periods during (2005-2006 summer season and during winter season to detect the impact of climate on treated wastewater quality. Soil samples were collected from Al-Lajoun valley where the treated wastewater drained, to determine the heavy metal and total organic carbon concentrations at same time. The study showed that the treated wastewater was low in its heavy metals contents during both winter and summer seasons, which was attributed to high pH value enhancing their precipitations. Some of the major ions such as Cl-, Na+, HCO33-, Mg2+ in addition to biological oxygen demand and chemical oxygen demand were higher than the recommended Jordanian guidelines for drained water in valleys. The treated wastewater contained some organic compounds of toxic type such as polycyclic aromatic hydrocarbons. Results showed that the soil was low in its heavy metal contents and total organic carbon with distance from the discharging pond, which attributed to the adsorption of heavy metals, total organic carbon and sedimentation of suspended particulates. From this study it was concluded that the treated wastewater must be used in situ for production of animal fodder and prohibit its contact with the surface and groundwater resources of the area specially Al-Mujeb dam where it is collected.

Turbidity-based monitoring of particle concentrations and flocculant requirement in wastewater pre-treatment

NARCIS (Netherlands)

Mels, A.R.; Spanjers, H.; Klapwijk, A.

2004-01-01

The removal of particulate organic material in the first step of wastewater treatment may result in significant savings of reactor volume and energy at wastewater treatment plants, because the organic loading to pursuing unit operations can be reduced. This article describes experiments into the

CHEMICAL EXAMINATION OF JACK TREE LATEX AND

Indian Academy of Sciences (India)

and on Saponification yielded fatty acids, Volatile as well as non-volatile. The unsaponifiable portion on repeated crystallisation provided a crystal- line, sharp melting compound which was identified as artostenone? from a. Latex (200 c.c.). ത്ത min- pe. Coagulum (A) Aqueous alcoholic solution (B). Acetone or ethyl acetate ...

Efficacy of protection by latex gloves during orthodontic therapy.

Science.gov (United States)

Doll, G M; Zentner, A; Balan, R; Sergl, H G

2000-01-01

The wearing of gloves during orthodontic or dental treatment is generally indicated for reasons of hygiene and protection against infection. This study was aimed at determining the extent and localization of perforations caused by the various orthodontic treatment techniques and interrupting the infection barrier. The impermeability was tested by means of a water retention test according to European standard EN 455, Part 1, performed on 1600 Centramed (Centramed, Koblenz), Tekmedic and SafeEx non-sterile disposable latex gloves (both by Safe Med, Switzerland) and Safe Gan latex gloves with an additional acrylate coating (also by Safe Med). The perforation rate in unused gloves was between 0.5% and 7.5%, rising on average to 11% with increasing use. 36% of the total number of lesions resulted from handling removable appliances, and 57% from handling fixed appliances, especially when replacing arch wires and elastics. Most lesions were in the thumb, index finger and palm region. Only 18% of the defects were noticed by the dentists themselves. The gloves worn by beginners in their first year of postgraduate orthodontic training had about twice as many defects as those worn by qualified orthodontists. When patients with an increased risk of infection are to be treated, additional hand disinfection measures should be taken and 2 pairs of gloves worn in view of the relatively unreliable protection offered by commercially available latex gloves.

Characteristic of natural rubber latex-methyl metha-crylate copolymer in mineral lubricant base oil

International Nuclear Information System (INIS)

Meri Suhartini; Rahmawati

2010-01-01

Natural rubber latex-methyl methacrylate copolymer was diluted in xylene, then diluted in four types of lubricant base oil with concentrations of 0.25%, 1%, 5%, and 10%. The mixed solutions were analyzed to obtain kinematics viscosity, viscosity index, density, ash content, metal content, flash point, shear stability and total alkali number. The viscosity index of sample, increased by adding the copolymer solution. The results showed that lubricant base oil of High Viscosity index (HVI) 60 and mixed HVI 60: HVI 650 gave optimum viscosity index. The higher concentration of polymer added into base lubricant oil, the higher viscosity index obtained. The shear stability test showed that the kinematics viscosity of sample decreased 6.5% after 60 minutes of treatment test. (author)

Segregation of metals-containing wastewater by pH

International Nuclear Information System (INIS)

Taylor, P.A.; McTaggart, D.R.

1990-10-01

A pH-based sampling system has shown that there is a high correlation between low pH and metals contamination for the wastewater from the 4500 area (manhole 190) and the 2000 area (pump station). Wastewater from the Radiochemical Engineering Development Center (REDC) and the High Flux Isotope Reactor (HFIR) has not shown any metals concentrations above the National Pollutant Discharge Elimination System (NPDES) permit limits for the Nonradiological Wastewater Treatment Plant (NRWTP). It is recommended that pH be used as the diversion criteria for wastewater from manhole 190 and the pump station to be sent to the metals tank of the NRWTP. Any wastewater with a pH less than 6.0 or greater than 10.0 should be sent to the metals tank. Based on the results of 29 weeks of sampling, it is expected that on the order of 36m 3 /wk (9500 gal/wk) of wastewater will be diverted to the metals tank of the NRWTP. Wastewater from REDC and HFIR can be sent to the nonmetals tank, but it should be sampled periodically and analyzed by Inductively Coupled Plasma (ICP) spectrophotometer to confirm that the metals concentration is not increasing. 1 ref., 2 figs., 9 tabs

Spatial and temporal shifts in gross primary productivity, respiration, and nutrient concentrations in urban streams impacted by wastewater treatment plant effluent

Science.gov (United States)

Ledford, S. H.; Toran, L.

2017-12-01

Impacts of wastewater treatment plant effluent on nutrient retention and stream productivity are highly varied. The working theory has been that large pulses of nutrients from plants may hinder in-stream nutrient retention. We evaluated nitrate, total dissolved phosphorus, and dissolved oxygen in Wissahickon Creek, an urban third-order stream in Montgomery and Philadelphia counties, PA, that receives effluent from four wastewater treatment plants. Wastewater treatment plant effluent had nitrate concentrations of 15-30 mg N/L and total dissolved phosphorus of 0.3 to 1.8 mg/L. Seasonal longitudinal water quality samples showed nitrate concentrations were highest in the fall, peaking at 22 mg N/L, due to low baseflow, but total dissolved phosphorous concentrations were highest in the spring, reaching 0.6 mg/L. Diurnal dissolved oxygen patterns above and below one of the treatment plants provided estimates of gross primary productivity (GPP) and ecosystem respiration (ER). A site 1 km below effluent discharge had higher GPP in April (80 g O2 m-2 d-1) than the site above the plant (28 g O2 m-2 d-1). The pulse in productivity did not continue downstream, as the site 3 km below the plant had GPP of only 12 g O2 m-2 d-1. Productivity fell in June to 1-2 g O2 m-2 d-1 and the differences in productivity above and below plants were minimal. Ecosystem respiration followed a similar pattern in April, increasing from -17 g O2 m-2 d-1 above the plant to -47 g O2 m-2 d-1 1 km below the plant, then decreasing to -8 g O2 m-2 d-1 3 km below the plant. Respiration dropped to -3 g O2 m-2 d-1 above the plant in June but only fell to -9 to -10 g O2 m-2 d-1 at the two downstream sites. These findings indicate that large nutrient pulses from wastewater treatment plants spur productivity and respiration, but that these increases may be strongly seasonally dependent. Examining in-stream productivity and respiration is critical in wastewater impacted streams to understanding the seasonal and

Study on concentrating treatment test of simulated radioactive wastewater containing boron by reverse osmosis membrane in PWR NPP

International Nuclear Information System (INIS)

Ye Xinnan; Jiang Baihua; Fan Wenwen; Zhang Zhiyin; Yang Cangsheng

2015-01-01

The reverse osmosis membrane equipment in PWR NPP was employed to investigate the application of pilot scale system in the radioactive wastewater treatment at the full recirculation operation. The removal performance of the equipment for the boron and the radioactivity nuclide were studied, respectively. The experimental results show that the removal efficiency of the aromatic polyamide composite reverse osmosis membrane for boron is over 83.3% and the concentration of boron in concentrate is over 10000 mg/L. The experimental results also show that the removal efficiency of two nuclides including cobalt and cesium is over 97.9%. (authors)

Assessment of the mutagenic and antimutagenic activity of Synadenium umbellatum Pax latex by micronucleus test in mice

Directory of Open Access Journals (Sweden)

PR. Melo-Reis

Full Text Available Synadenium umbellatum Pax, popularly known as "cola-nota", is a medicinal plant that grows in tropical regions. The latex of this plant is used against various diseases, such as diabetes mellitus, leprosy, tripanosomiasis, leukemia, and several malignant tumors. The mutagenic, antimutagenic, and cytotoxic effects of the latex of this plant were investigated by measuring the frequency of micronuclei in mice bone marrow cells. To evaluate mutagenicity, the animals were treated with four doses of latex (10, 30, 50, and 100 mg/kg body weight. To study the antimutagenic activity, the animals were simultaneously treated with latex and mitomycin C (4 mg/kg. The cytotoxicity was evaluated by polychromatic and normochromatic erythrocytes ratio. Our results showed a significant increase of frequency of micronucleated polychromatic erythrocytes (MNPCE compared to the negative control group (p 0.05 was detected at the doses of 50 and 100 mg/kg. Under our experimental conditions, the results obtained indicate strong mutagenic and cytotoxic activity of S. umbellatum latex except the dose of 10 mg/kg and moderate antimutagenic effect at lower doses.

Copolymer natural latex in concrete: Dynamic evaluation through energy dissipation of polymer modified concrete

Science.gov (United States)

Andayani, Sih Wuri; Suratman, Rochim; Imran, Iswandi; Mardiyati

2018-05-01

Portland cement concrete have been used in construction due to its strength and ecomical value. But it has some limitations, such low flexural strength, low tensile strength, low chemical resistant and etc. Due to its limitations in flexural and tensile strength, Portland cement concrete more susceptible by seismic force. There are some methods for improving its limitations. Polymer addition into concrete mixture could be one of solution for improving the flexural and tensile strength, in aiming to get erthquake resistant properties. Also, the eartquake resistant could be achieved by improving energy dissipation capacity. In this research, the earthquake resistant evalution was approached from dynamic evaluation through energy dissipation capacity, after polymer addition as concrete additives. The polymers were natural latex (Indonesian naural resource) grafted with styrene and methacrylate, forming copolymer - natural latex methacrylate (KOLAM) and copolymer - natural latex styrene (KOLAS). They were added into concrete mixture resulting polymer modified concrete. The composition of polymer are 1%, 5% and 10% weight/weight of cement. The higher capacity of energy dissipation will give more capability in either absorbing or dissipating energy, and it was predicted would give better earthquake resistant.. The use of KOLAM gave better performance than KOLAS in energy dissipation capacity. It gave about 46% for addition of 1% w/w compared to Portland cement concrete. But for addition 5% w/w and 10% w/w, they gave about 7% and 5% higher energy dissipation capacity. The KOLAM addition into concrete mixture would reduce the maximum impact load with maximumabout 35% impact load reducing after 1% w/w addition. The higher concentration of KOLAM in concrete mixture, lower reducing of impact load, they were about 4% and 3% for KOLAM 5% and 10%. For KOLAS addition in any compositions, there were no positive trend either in energy dissipation capacity or impact load properties

Effects of radio sensitizers in the vulcanization of natural rubber latex induced by gamma radiation

International Nuclear Information System (INIS)

Souza, A. de; Canavel, V.; Araujo, S.C. de; Guedes, S.M.L.

1992-01-01

The effect of C Cl 4 and n-butyl acrylate as a sensitizer for radiation vulcanization of 60% DRC natural rubber latex with gamma rays, was studied relating tensile strength of vulcanized latex. The vulcanization dose is 200 kGy for natural rubber latex and it decreases to 40 kGy and to 9 kGy in the presence of C Cl 4 / potassium laureate and n-butyl acrylate / t-butyl hydroperoxide, respectively. The H 2 O 2 as a co-sensitizer does not change the efficiency of the combination of these sensitizers. The IV spectra show the formation of C=O after the irradiation as consequence of oxidation reactions. (author)

Optical response of a flat metallic surface coated with a monolayer array of latex spheres

International Nuclear Information System (INIS)

Shi Lei; Liu Xiaohan; Yin Haiwei; Zi Jian

2010-01-01

We report on the fabrication, characterization and simulation of a structure consisting of a flat metallic surface coated with a monolayer array of latex spheres. This structure shows interesting optical response: over flat metallic surfaces a series of reflection minima appear in reflection spectra. Numerical simulations revealed that the structure can support two types of surface modes: surface plasmon-polaritons bound at the metallic surface and guided modes confined to the array of latex spheres, or their hybrids. Both experimental and theoretical results indicated that these surface modes show well-defined band structures due to the introduced periodicity by the monolayer array of latex spheres.

Development assessment of natural latex membranes: a new proposal for the treatment of amblyopia

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, Jaqueline Alves; Rosa, Suelia Rodrigues Fleury, E-mail: jackalvesribeiro@gmail.com [Laboratorio de Engenharia e Biomaterial (BioEngLab), Faculdade Gama, Universidade de Brasilia (UnB), DF (Brazil); Leite, Cicilia Raquel Maia; Vasconcelos, Claudio Lopes; Soares, Joao Maria [Universidade do Estado do Rio Grande do Norte (UERN), Mossoro, RN (Brazil)

2017-05-15

The ophthalmic dysfunction amblyopia, commonly known as lazy eye, is characterized by decreased vision in one eye due to improper development in childhood. The aim of this study was to obtain and characterize natural rubber membranes and to assess their utility as an eye film capable of altering the passage of light. The latex membranes were produced using the Van Gogh method and the deposition technique and were analyzed by physical and chemical methods to determine the properties of latex in natura and of natural rubber membranes. The materials were characterized by X-ray diffractometry, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, analysis of water sorption and light crossing analysis. We report here a new approach to the treatment of patients with amblyopia using latex membranes. (author)

Development assessment of natural latex membranes: a new proposal for the treatment of amblyopia

International Nuclear Information System (INIS)

Ribeiro, Jaqueline Alves; Rosa, Suelia Rodrigues Fleury; Leite, Cicilia Raquel Maia; Vasconcelos, Claudio Lopes; Soares, Joao Maria

2017-01-01

The ophthalmic dysfunction amblyopia, commonly known as lazy eye, is characterized by decreased vision in one eye due to improper development in childhood. The aim of this study was to obtain and characterize natural rubber membranes and to assess their utility as an eye film capable of altering the passage of light. The latex membranes were produced using the Van Gogh method and the deposition technique and were analyzed by physical and chemical methods to determine the properties of latex in natura and of natural rubber membranes. The materials were characterized by X-ray diffractometry, scanning electron microscopy, thermogravimetry, differential scanning calorimetry, analysis of water sorption and light crossing analysis. We report here a new approach to the treatment of patients with amblyopia using latex membranes. (author)

Determination of beta-adrenergic receptor blocking pharmaceuticals in united states wastewater effluent

Energy Technology Data Exchange (ETDEWEB)

Huggett, D.B.; Khan, I.A.; Foran, C.M.; Schlenk, D

2003-02-01

This is the first report of beta-adrenergic receptor antagonist pharmaceuticals in United States wastewater effluent. - Beta adrenergic receptor antagonists ({beta}-Blockers) are frequently prescribed medications in the United States and have been identified in European municipal wastewater effluent, however no studies to date have investigated these compounds in United States wastewater effluent. Municipal wastewater effluent was collected from treatment facilities in Mississippi, Texas, and New York to investigate the occurrence of metoprolol, nadolol, and propranolol. Propranolol was identified in all wastewater samples analyzed (n=34) at concentrations {<=}1.9 {mu}g/l. Metoprolol and nadolol were identified in {>=}71% of the samples with concentrations of metoprolol {<=}1.2 {mu}g/l and nadolol {<=}0.36 {mu}g/l. Time course studies at both Mississippi plants and the Texas plant indicate that concentrations of propranolol, metoprolol, and nadolol remain relatively constant at each sampling period. This study indicates that {beta}-Blockers are present in United States wastewater effluent in the ng/l to {mu}g/l range.

Effect of rootstock on the scion of Hevea brasiliensis through metabolic analysis of latex samples by 1H NMR

Directory of Open Access Journals (Sweden)

Eduardo Sanches Pereira do Nascimento

2011-01-01

Full Text Available In this study, the effect of rootstock on grafting through metabolomic analysis of latex (Hevea brasiliensis samples was verified by 1H nuclear magnetic resonance (NMR and multivariate data analysis. Sixteen metabolites present in the latex cytosol were characterized by NMR. PCA analysis showed that the latex samples of the RR and GR groups can be differentiated. The GR group samples present a metabolic profile similar to the RR group samples, while the RG group is in an intermediate position between RR and GG groups. Sucrose and formate contributed greatly to the separation obtained by PCA, presenting a good correlation between the results. 1H NMR was an efficient technique to differentiate latex samples from different types of rootstocks and grafting and in the future could be used to predict rubber production by latex analysis.

Effect of gamma radiation dose and sensitizer on the physical properties of irradiated natural rubber latex

International Nuclear Information System (INIS)

Komgrit, R.; Thawat, C.; B, Tripob; Wirach, T.

2009-07-01

Full text: The vulcanization of natural rubber latex can be induced by gamma radiation, which enhances cross-linking within the rubber matrix. The purpose of this research is to investigate the effect of gamma radiation dose and sensitizers on the physical properties of irradiated natural rubber. Three sensitizers n-butyl acrylate (n-B A), tetrachloroethylene (C 2 Cl 4 ) and trichloromethane (CHCl 3 ) were mixed with natural rubber latex before irradiation with gamma ray dose varied from 14 to 22 kGy. Results showed that the mixture of three sensitizers with specific ratios effectively induced the cross-linking of natural rubber latex. The cross-linking ratio and improved physical properties increased with increasing gamma dose. Therefore, the mixture ratios of n-B A, C 2 Cl 4 and CHCl 3 have shown to be a critical parameter in the vulcanization of natural rubber latex by gamma radiation

Removal of ammonia nitrogen in wastewater by microwave radiation: A pilot-scale study

International Nuclear Information System (INIS)

Lin Li; Chen Jing; Xu Zuqun; Yuan Songhu; Cao Menghua; Liu Huangcheng; Lu Xiaohua

2009-01-01

A large removal of ammonia nitrogen in wastewater has been achieved by microwave (MW) radiation in our previous bench-scale study. This study developed a continuous pilot-scale MW system to remove ammonia nitrogen in real wastewater. A typical high concentration of ammonia nitrogen contaminated wastewater, the coke-plant wastewater from a Coke company, was treated. The output power of the microwave reactor was 4.8 kW and the handling capacity of the reactor was about 5 m 3 per day. The ammonia removal efficiencies under four operating conditions, including ambient temperature, wastewater flow rate, aeration conditions and initial concentration were evaluated in the pilot-scale experiments. The ammonia removal could reach about 80% for the real coke-plant wastewater with ammonia nitrogen concentrations of 2400-11000 mg/L. The running cost of the MW technique was a little lower than the conventional steam-stripping method. The continuous microwave system showed the potential as an effective method for ammonia nitrogen removal in coke-plant water treatment. It is proposed that this process is suitable for the treatment of toxic wastewater containing high concentrations of ammonia nitrogen.

The Synthesis and Modification of Nanosized Clickable Latex Particles

KAUST Repository

Almahdali, Sarah

2013-01-01

This research aims to add to the current knowledge available for miniemulsion polymerization reactions and to use this knowledge to synthesize multifunctional nanosized latex particles that have the potential to be used in catalysis. The physical

Partial swelling of latex particles by two monomers

NARCIS (Netherlands)

Noel, E.F.J.; Maxwell, I.A.; German, A.L.

1993-01-01

The swelling of polymeric latex particles with solvent and monomer is of great importance for the emulsion polymn. process in regard to compn. drift and rate of polymn. For the monomer combination, Me acrylate-vinyl acetate, both satn. and partial swelling were detd. exptl. Theories for satn.

Effects of ionizing radiation on struvite crystallization of livestock wastewater

International Nuclear Information System (INIS)

Kim, Tak- Hyun; Nam, Yun-Ku; Joo Lim, Seung

2014-01-01

Livestock wastewater is generally very difficult to be treated by conventional wastewater treatment techniques because it contains high-strength organics (COD), ammonium (NH 4 + ), phosphate (PO 4 3− ) and suspended solids. Struvite crystallization has been recently studied for the simultaneous removal of NH 4 + and PO 4 3− . In this study, gamma ray irradiation was carried out prior to struvite crystallization of the anaerobically digested livestock wastewater. The effects of gamma ray irradiation on the struvite crystallization of livestock wastewater were investigated. As a result, gamma ray irradiation can decrease the concentration of COD, NH 4 + and PO 4 3− contained in the livestock wastewater. This results in not only an enhancement of the struvite crystallization efficiency but also a decrease in the chemical demands for the struvite crystallization of livestock wastewater. - Highlights: • Gamma ray was applied prior to struvite crystallization of livestock wastewater. • Gamma ray resulted in an enhancement of struvite crystallization efficiency. • This is due to the decrease of COD concentration by gamma ray irradiation

Wastewater treatment of chemical laboratory using electro assisted-phytoremediation (EAPR)

Science.gov (United States)

Putra, Rudy Syah; Trahadinata, Gilang Ahmad; Latif, Arif; Solehudin, Mochamad

2017-03-01

The EAPR process using water hyacinth (Eichornia crassipes) on the wastewater treatment of chemical laboratory had been evaluated. The purpose of the EAPR process was to decrease the BOD, COD and heavy metal concentration in the wastewater. The effectiveness of the process on the wastewater treatment was evaluated using COD, BOD, and heavy metal (Pb, Cu) concentration, respectively. The result showed that the EAPR process decrease the COD, BOD, Pb and Cu in the 4 h of EAPR process. Those concentrations were met the water quality standard of class IV according to government regulation No. 82/2001 regarding the water quality management and water pollution control of the Republic of Indonesia.

Latex Imaging by Environmental STEM: Application to the Study of the Surfactant Outcome in Hybrid Alkyd/Acrylate Systems

OpenAIRE

Faucheu , Jenny; Chazeau , Laurent; Gauthier , Catherine; Cavaille , Jean-Yves; Goikoetxea , Monika; Minari , Roque; Asua , Jose M.

2009-01-01

International audience; Among other uses. latexes are a successful alternative to solvent-borne binders for coatings. Efforts are made to produce hybrid nanostructured latexes containing an acrylic phase and an alkyd phase, However, after the film-forming process, the surfactant used to stabilize these latexes remains in the film, and its location can have a drastic effect on the application properties. Among the processing parameters, the alkyd hydrophobicity can strongly influence this loca...

[Source identification of toxic wastewaters in a petrochemical industrial park].

Science.gov (United States)

Yang, Qian; Yu, Yin; Zhou, Yue-Xi; Chen, Xue-Min; Fu, Xiao-Yong; Wang, Miao

2014-12-01

Petrochemical wastewaters have toxic impacts on the microorganisms in biotreatment processes, which are prone to cause deterioration of effluent quality of the wastewater treatment plants. In this study, the inhibition effects of activated sludge's oxygen consumption were tested to evaluate the toxicity of production wastewaters in a petrochemical industrial park. The evaluation covered the wastewaters from not only different production units in the park, but also different production nodes in each unit. No direct correlation was observed between the toxicity effects and the organic contents, suggesting that the toxic properties of the effluents could not be predicted by the organic contents. In view of the variation of activated sludge sensitivity among different tests, the toxicity data were standardized according to the concentration-effect relationships of the standard toxic substance 3, 5-dichlorophenol on each day, in order to improve the comparability among the toxicity data. Furthermore, the Quality Emission Load (QEL) of corresponding standard toxic substance was calculated by multiplying the corresponding 3, 5-dichlorophenol concentration and the wastewater flow quantity, to indicate the toxicity emission contribution of each wastewater to the wastewater treatment plant. According to the rank list of the toxicity contribution of wastewater from different units and nodes, the sources of toxic wastewater in the petrochemical industrial park were clearly identified. This study provides effective guidance for source control of wastewater toxicity in the large industrial park.

Oxygen enriched air using membrane for palm oil wastewater treatment

Directory of Open Access Journals (Sweden)

Ramlah Mohd Tajuddin

2002-11-01

Full Text Available A research aimed to explore new method of aeration using oxygen enriched air performance on BOD reduction of palm oil wastewater was conducted. The oxygen enriched air was obtained from an Oxygen Enriched System (OES developed using asymmetric polysulfone hollow fiber membrane with composition consisting of PSF: 22%, DMAc: 31.8%, THF: 31.8%, EtOH: 14.4%. Palm oil wastewater samples were taken from facultative pond effluent. These samples were tested for its initial biochemical oxygen demand (BOD, total suspended solids (TSS, pH, conductivity, turbidity, dissolved oxygen (DO, suspended solids (SS, and total dissolved solids (TDS before being subjected to two modes of aeration system, that is diffused air and oxygen enriched air. These water quality concentrations were tested for every 20 minutes for two-hour period during the aeration process. Results of BOD, TSS, pH, conductivity, DO, SS and TDS concentrations against time of samples from the two modes of aeration were then compared. It was found that DO concentration achieved in oxygen enriched air aeration was better than aeration using diffused air system. Aeration using OES improve the DO concentration in the wastewater and thus improve the BOD reduction and also influence other physical characteristics of wastewater. This phenomenon indicates the advantage of using air with higher oxygen concentration for wastewater aeration instead of diffused air system.

Concentrating molasses distillery wastewater using biomimetic forward osmosis (FO) membranes

DEFF Research Database (Denmark)

Singh, N.; Petrinic, I.; Hélix-Nielsen, Claus

2018-01-01

Treatment of sugarcane molasses distillery wastewater is challenging due to the presence of complex phenolic compounds (melanoidins and polyphenols) having antioxidant properties. Due to zero liquid discharge regulations, Indian distilleries continue to explore effective treatment options...

Green synthesis of colloidal silver nanoparticles using natural rubber latex extracted from Hevea brasiliensis.

Science.gov (United States)

Guidelli, Eder José; Ramos, Ana Paula; Zaniquelli, Maria Elisabete D; Baffa, Oswaldo

2011-11-01

Colloidal silver nanoparticles were synthesized by an easy green method using thermal treatment of aqueous solutions of silver nitrate and natural rubber latex (NRL) extracted from Hevea brasiliensis. The UV-Vis spectra detected the characteristic surface plasmonic absorption band around 435 nm. Both NRL and AgNO(3) contents in the reaction medium have influence in the Ag nanoparticles formation. Lower AgNO(3) concentration led to decreased particle size. The silver nanoparticles presented diameters ranging from 2 nm to 100 nm and had spherical shape. The selected area electron diffraction (SAED) patterns indicated that the silver nanoparticles have face centered cubic (fcc) crystalline structure. FTIR spectra suggest that reduction of the silver ions are facilitated by their interaction with the amine groups from ammonia, which is used for conservation of the NRL, whereas the stability of the particles results from cis-isoprene binding onto the surface of nanoparticles. Therefore natural rubber latex extracted from H. brasiliensis can be employed in the preparation of stable aqueous dispersions of silver nanoparticles acting as a dispersing and/or capping agent. Moreover, this work provides a new method for the synthesis of silver nanoparticles that is simple, easy to perform, pollutant free and inexpensive. Copyright © 2011 Elsevier B.V. All rights reserved.

Design and operation of UASB—A/O process for treatment starch and VB12 wastewater

Directory of Open Access Journals (Sweden)

Yuanyuan CHEN

2016-12-01

Full Text Available Starch and VB12 wastewater with higher COD and ammonia nitrogen concentration, contains a large number of difficult biodegradable material, complex composition, is difficult to deal with. In recent years, with the increasingly stringent wastewater discharge standards, require the use of a stable and efficient wastewater treatment process for purification treatment of high concentration of ammonia nitrogen in wastewater and the refractory organic pollutants, to achieve discharge standards. Upflow Anaerobic Sludge Blanket (UASB—Anoxic/Oxic(A/O process was employed in a wastewater treatment of starch and Vitamin B12 wastewater, which was 5 000 m3/d with highly concentrated organic pollutants and ammonia. The efficiency and reliability of the process has been proven. The results of the system operation show that the concentration of the effluent COD, ammonia and total nitrogen (TN were at 78.4 mg/L, 18.7 mg/L and 41.1 mg/L, and the treatment efficiencies of COD, ammonia and TN reached over 99%, 92.1%, 82.7%, respectively, when the influent COD and TN concentration were in the ranges of 8 544~9 720 mg/L and 240~250 mg/L. The quality of the treated wastewater met the first-class discharge standards in Integrated Wastewater Discharge Standard(GB 8978—1996.

[Changes in the peripheral blood of workers engaged in ethylbenzene-styrene and synthetic rubber and latex manufacture].

Science.gov (United States)

Khristeva, V

1986-01-01

A total of 67 workers were examined from the production of "Ethyl benzene-styrene" and 184 workers from the production of "Synthetic rubber and latex", as well as a control group of 59 employees. The workers from the first production are exposed to the effect of styrene, ethyl benzene and toluene. The concentrations of the substances surpass MAC, with several times, at the majority of the working places. The workers with a length of service over 10 years predominate. The workers from the second production are exposed to the combined effect of styrene and divinyl, their concentrations fluctuating from 2 to 8 times over MAC. The workers with a length of service over 10 years are 71.7%. The deviations, established in the hematological indices studied are compared with the results from a study on the workers from those productions of 6 years ago. Dynamics in the changes was established among the workers from the production of "Synthetic rubber and latex", associated with the duration of occupational exposure to styrene and divinyl. In case of a shorter length of service, the deviations are functional (reduction of peroxidase activity in granulocytes), increase of hemoglobin and hematocrit, associated with the adaptive reaction of organism. Pronounced anemic syndrome was established in a considerable number (24 workers) after an exposure of 10 years as well as lymphocytosis (35 subjects) and leukopenia (9 subjects).

Concentration of PAHs in Municipal Wastewater in Selected Sewer Collectors of the Upper Silesian Urban Area, Poland

Directory of Open Access Journals (Sweden)

Pistelok Franciszek

2014-12-01

(GC-MS. The concentrations of 16 PAHs sum (EPA list ranged between 1.025 and 3.056 μg/L. Phenanthrene dominated in nearly all the analysed samples. The contents of PAHs, which are priority hazardous substances according to the directive, were high in the analysed samples. The obtained results and the analysis of diagnostic ratios for the emissions of PAHs into the air helped to reach the conclusion that traffic emissions were the main source of PAHs in the examined wastewater.

Extractable protein content of radiation vulcanized natural rubber latex films

International Nuclear Information System (INIS)

Ma'zam Md Said; Wan Manshol Wan Zin

1996-01-01

The effects of processing conditions on extractable protein content of coagulant dipped radiation vulcanized natural rubber latex films have been investigated. Drying of wet-gel of radiation vulcanized latex films even at a relatively low temperature of 70 degree C resulted in increases of extractable protein content of the films. The extractable protein content is dependent upon both the temperature and time of drying of wet-gel deposit. Wet-gel leaching of film alone is not adequate to reduce the extractable protein content of films to low levels. Combination of wet-gel leaching, post-leaching, a dip in corn starch slurry, followed by drying at a low temperature of 70 degree C reduces the extractable protein content of films to very low levels

Advances in HTGR Wastewater Treatment System Design

International Nuclear Information System (INIS)

Li Junfeng; Qiu Yu; Wang Jianlong; Jia Fei

2014-01-01

The source terms of radioactive wastewater from HTR-PM were introduced. Concentration process should be used to reduce volume. A radioactive wastewater treatment system was designed by using Disc tubular reverse osmosis (DTRO) membrane system. The pretreatment system was simplify by using a cartridge filter. A three-stage membrane system was built. The operated characters to treat low and intermediate radioactive waste water were studied. A concentration rates of 25-50 is reached. The decontamination factor of the membrane system can reach 30-100. (author)

Green Approach in the Bio-removal of Heavy Metals from wastewaters

Directory of Open Access Journals (Sweden)

Gani Paran

2017-01-01

Full Text Available Cultivation of microalgae has been suggested as a green approach for a sustainable wastewater treatment especially heavy metal bioremediation. This study investigated the bio-removal of zinc (Zn, iron (Fe, cadmium (Cd and manganese (Mn from domestic wastewater (DW and food processing wastewater (FW using green microalgae, Botryococcus sp.. The total of five treatments represented by five different cell concentrations (1×103, 1×104, 1×105, 1×106 and 1×107 cells/mL of Botryococcus sp. in the wastewaters medium. The results revealed high removal efficiency of Zn, Fe, Cd and Mn after 18 days of the culture compared to control (wastewaters without algae. In DW , Zn, Fe, Cd and Mn were successfully removed at the highest efficiencies up to 71.5%, 51.2%, 83.5% and 97.2%, respectively while in FW, the same metal concentrations were reduced by up to 64.4%, 53.3%, 52.9% and 26.7%, respectively. Overall, most of the algae cell concentrations tested were successfully reducing the metals contaminant presence in both wastewaters and provides a baseline for further phycoremediation coupled with biomass production.

Bioremediation of wastewater using microalgae

Science.gov (United States)

Chalivendra, Saikumar

Population expansion and industrial development has deteriorated the quality of freshwater reservoirs around the world and has caused freshwater shortages in certain areas. Discharge of industrial effluents containing toxic heavy metals such as Cd and Cr into the environment have serious impact on human, animal and aquatic life. In order to solve these problems, the present study was focused on evaluating and demonstrating potential of microalgae for bioremediation of wastewater laden with nitrogen (N) in the form of nitrates, phosphorous (P) in the form of phosphates, chromium (Cr (VI)) and cadmium (Cd (II)). After screening several microalgae, Chlorella vulgaris and algae taken from Pleasant Hill Lake were chosen as candidate species for this study. The viability of the process was demonstrated in laboratory bioreactors and various experimental parameters such as contact time, initial metal concentration, algae concentration, pH and temperature that would affect remediation rates were studied. Based on the experimental results, correlations were developed to enable customizing and designing a commercial Algae based Wastewater Treatment System (AWTS). A commercial AWTS system that can be easily customized and is suitable for integration into existing wastewater treatment facilities was developed, and capital cost estimates for system including installation and annual operating costs were determined. The work concludes that algal bioremediation is a viable alternate technology for treating wastewater in an economical and sustainable way when compared to conventional treatment processes. The annual wastewater treatment cost to remove N,P is ~26x lower and to remove Cr, Cd is 7x lower than conventional treatment processes. The cost benefit analysis performed shows that if this technology is implemented at industrial complexes, Air Force freight and other Department of Defense installations with wastewater treatment plants, it could lead to millions of dollars in

Effect of Phosphate levels on vegetables irrigated with wastewater

Science.gov (United States)

Oladeji, S. O.; Saeed, M. D.

2018-04-01

This study examined accumulation of phosphate ions in wastewater and vegetables through man-made activities. Phosphate level was determined in wastewater and vegetables collected on seasonal basis along Kubanni stream in Zaria using UV/Visible and Smart Spectro Spectrophotometers for their analyses. Results obtained show that phosphate concentrations ranged from 3.85 – 42.33 mg/L in the first year and 15.60 – 72.80 mg/L in the second year for wastewater whereas the vegetable had levels of 3.80 – 23.65 mg/kg in the year I and 7.48 – 27.15 mg/kg in the year II. Further statistical tests indicated no significant difference in phosphate levels across the locations and seasons for wastewater and vegetables evaluated. Correlation results for these two years indicated negative (r = -0.062) relationship for wastewater while low (r = 0.339) relationship noticed for vegetables planted in year I to that of year II. Phosphate concentrations obtained in this study was higher than Maximum Contaminant Levels set by Standard Organization such as WHO and FAO for wastewater whereas vegetables of the sampling sites were not contaminated with phosphate ions. Irrigating farmland with untreated wastewater has negative consequence on the crops grown with it.

Identification of wastewater processes

DEFF Research Database (Denmark)

Carstensen, Niels Jacob

The introduction of on-line sensors for monitoring of nutrient salts concentrations on wastewater treatment plants with nutrient removal, opens a wide new area of modelling wastewater processes. The subject of this thesis is the formulation of operational dynamic models based on time series...... of ammonia, nitrate, and phosphate concentrations, which are measured in the aeration tanks of the biological nutrient removal system. The alternatign operation modes of the BIO-DENITRO and BIO-DENIPHO processes are of particular interest. Time series models of the hydraulic and biological processes are very......-known theory of the processes with the significant effects found in data. These models are called grey box models, and they contain rate expressions for the processes of influent load of nutrients, transport of nutrients between the aeration tanks, hydrolysis and growth of biomass, nitrification...

Radiation vulcanization of natural rubber latex using 250 keV electron beam machine

Energy Technology Data Exchange (ETDEWEB)

Chirinos, H.; Yoshii, F.; Makuuchi, K.; Lugao, A. E-mail: ablugao@net.ipen.br

2003-08-01

The sensitized radiation vulcanization of natural rubber latex has been carried out with 250 keV electrons. Latex was irradiated over a range of the beam current from 5 to 20 mA in the presence of sensitizers like the n-butyl acrylate (n-BA). The vulcanization dose decreases with increasing beam current condition. The rate of vulcanization (R{sub vul}) depends on the beam current (I) as given by the equation R{sub vul}=kI{sup 0.6}.

Determination of beta-adrenergic receptor blocking pharmaceuticals in united states wastewater effluent

International Nuclear Information System (INIS)

Huggett, D.B.; Khan, I.A.; Foran, C.M.; Schlenk, D.

2003-01-01

This is the first report of beta-adrenergic receptor antagonist pharmaceuticals in United States wastewater effluent. - Beta adrenergic receptor antagonists (β-Blockers) are frequently prescribed medications in the United States and have been identified in European municipal wastewater effluent, however no studies to date have investigated these compounds in United States wastewater effluent. Municipal wastewater effluent was collected from treatment facilities in Mississippi, Texas, and New York to investigate the occurrence of metoprolol, nadolol, and propranolol. Propranolol was identified in all wastewater samples analyzed (n=34) at concentrations ≤1.9 μg/l. Metoprolol and nadolol were identified in ≥71% of the samples with concentrations of metoprolol ≤1.2 μg/l and nadolol ≤0.36 μg/l. Time course studies at both Mississippi plants and the Texas plant indicate that concentrations of propranolol, metoprolol, and nadolol remain relatively constant at each sampling period. This study indicates that β-Blockers are present in United States wastewater effluent in the ng/l to μg/l range

Evaluation of advanced wastewater treatment systems for water reuse in the era of advanced wastewater treatment

Science.gov (United States)

Kon, Hisao; Watanabe, Masahiro

This study focuses on effluent COD concentration from wastewater treatment in regards to the reduction of pathogenic bacteria and trace substances in public waters. The main types of secondary wastewater treatment were conventional activated sludge processes. Recently, however, advance wastewater treatment processes have been developed aimed at the removal of nitrogen and phosphorus, and the effluent quality of these processes was analyzed in this study. Treatment processes for water reclamation that make effluent to meet the target water quality for reuse purposes were selected and also optimum design parameters for these processes were proposed. It was found that the treatment cost to water reclamation was greatly affected by the effluent COD of the secondary treatment. It is important to maintain low COD concentration in the secondary treated effluent. Therefore, it is considered that adequate cost benefits would be obtained by achieving target COD quality through shifting from a conventional activated sludge process to an advanced treatment process.

Laboratory evaluation of a simple and rapid latex agglutination assay for the serodiagnosis of typhoid fever

NARCIS (Netherlands)

Abdoel, Theresia H.; Pastoor, Rob; Smits, Henk L.; Hatta, Mochammad

2007-01-01

A latex agglutination assay for the serodiagnosis of typhoid fever was evaluated on samples collected from patients with clinical suspicion of typhoid fever in South Sulawesi, Indonesia, where the disease is endemic. The latex assay is very easy to use, gives a rapid result and may be used as a

Biohydrogen production and wastewater treatment from organic wastewater by anaerobic fermentation with UASB

Science.gov (United States)

Wang, Lu; Li, Yong-feng; Wang, Yi-xuan; Yang, Chuan-ping

2010-11-01

In order to discuss the ability of H2-production and wastewater treatment, an up-flow anaerobic sludge bed (UASB) using a synthesized substrate with brown sugar wastewater was conducted to investigate the hydrogen yield, hydrogen producing rate, fermentation type of biohydrogen production, and the chemical oxygen demand (COD) removal rate, respectively. The results show that when the biomass of inoculants was 22.5 g SSṡL-1 and the influent concentration, hydraulic retention time (HRT) and initial pH were within the ranges of 4000˜6000 mg CODṡL-1, 8 h and 5-5.5, respectively, and the biohydrogen producing reactor could work effectively. The maximum hydrogen production rate is 5.98 Lṡd-1. Simultaneously, the concentration of ethanol and acetic acid is around 80% of the aqueous terminal production in the system, which presents the typical ethanol type fermentation. pH is at the range of 4˜4.5 during the whole performing process, however, the removal rate of COD is just about 20%. Therefore, it's still needs further research to successfully achieve the biohydrogen production and wastewater treatment, simultaneously.

Process design of high-concentration benzimidazole wastewater treatment based on the molecular structure of contaminants.

Science.gov (United States)

Li, Chenru; Qian, Kun; Liu, Qinyao; Zhang, Qianyi; Yao, Chen; Song, Wei; Wang, Yihong

2018-04-01

Benzimidazole is an important intermediate in industry and it is usually difficult to be degraded by many treatment technologies. Looking for a highly effective, environment-friendly degradation process for benzimidazole wastewater is of great significance to reduce pollution. Based on the structure of contaminants, the micro-electrolysis (ME) coupled with the Fenton technique was chosen to degrade the industrial benzimidazole wastewater. Special feeding was applied to maintain the suitable hydrogen peroxide (H 2 O 2 ) concentration to produce the hydroxyl radicals (•OH) as much as possible and protect •OH from being quenched by excess H 2 O 2 according to the reaction mechanism. The results showed that this combined technique was highly efficient to decompose benzimidazole compounds. More chemical oxygen demand (COD) could be reduced when flow control was used, compared to the flow not being controlled. The COD removal rate could reach 85.2% at optimal parameters. Then the effluent of this process was combined with the existing biochemical system for further degradation. The studies of Ultraviolet Spectrophotometry, Fourier Transform Infrared Spectroscopy and Liquid Chromatography Mass Spectrometry showed that both 2-(a-Hydroxyethyl) benzimidazole and 2-Acetylbenzimidazole were decomposed to the isopropanolamine and aniline after the ME treatment; then the intermediates were oxidized into oxalic acid after the Fenton reaction.

Future wastewater solutions: removal of pharmaceuticals in conventional wastewater treatment plants

DEFF Research Database (Denmark)

Jensen, Thomas

Residues of pharmaceuticals, personal care products and industrial chemicals find their way into the environment mainly through incomplete removal in the conventional urban wastewater treatment plants (WWTPs) and appear as micro-pollutants at pg L-1 to μg L-1 concentrations. WWTPs were designed...

Heavy metal pollution of vegetable crops irrigated with wastewater ...

African Journals Online (AJOL)

144) and edible parts of both exotic and traditional vegetables (samples = 240) irrigated with wastewater from some parts of Accra were studied. The concentrations of heavy metals in mg/l were quantified in wastewater from Accra and ...

Low field NMR study of the latex derived from Brosimum parinarioides - Moraceae

International Nuclear Information System (INIS)

Miguez, Eduardo; Tavares, Maria Ines B.

2009-01-01

Brosimum parinarioides is a tree found in the Amazonia forest and its latex (Leite de Amapa) is often used like food and by the popular medicine in the treatment of tuberculosis and asthma. Being swallowed in nature, its necessary determinate the stability degree of this latex in the storage conditions in which is used in Amazonia. The analyses of T 2 data showed that the limit of stability is not longer than six month in the storage conditions used by the population of Amazonia. The Low field NMR proved to be an efficient method for this kind of study. (author)

Characterization of Wastewaters obtained from Hatay Tanneries

Directory of Open Access Journals (Sweden)

Şana Sungur

2017-06-01

Full Text Available The leather tanning industry is one of the most significant pollutants in terms of both conventional and toxic parameters. On the other hand, leather industry has an important economic role both in Turkey and in the World. In this study, wastewater samples were taken from 15 different tanneries in the Hatay Region. Wastewaters obtained from liming process and chromium tanning process was analyzed. Sulfide, chromium (III, chromium (VI, oil and grease, total suspended solids (TSS, organic matters, biochemical oxygen demand (BOD, chemical oxygen demand (COD, pH and alkalinity were determined according to Turkish Standard Methods. The determined averages values belong to wastewaters obtained from liming process were as following: pH 11.71; COD 16821 mg L-1; BOD 4357 mg L-1; TSS 39023 mg L-1; oil and grease 364 mg L-1; S-2 concentration 802 mg L-1; alkalinity 2115 mg L-1. The determined averages values belong to wastewaters obtained from chromium tanning process were also as following: pH 4.23; COD 6740 mg L-1; BOD 377 mg L-1; Cr+3 concentrations 372 mg L-1; Cr+6 concentrations 127 mg L-1; TSS 14553 mg L-1; oil and grease 343 mg L-1. The results of all analyzes were higher than wastewater discharge standards. As a result, it’s necessary to use more effective treatments in order to reduce the negative impacts of leather tanning industry that affect environment, natural water resources and at last human health and welfare.

Effect of cellulose nanocrystals from corn cob with dispersion agent polyvinyl pyrrolidone in natural rubber latex film after aging treatment

Science.gov (United States)

Harahap, H.; Ridha, M.; Halimatuddahliana; Taslim; Iriany

2018-02-01

This study about the resistance of natural rubber latex films using nanocrystals cellulose filler from corn cob waste by aging treatment. Corn cob used as organic filler composed of cellulose, hemicellulose, and lignin. Each component has a potential for reuse, such as cellulose. Cellulose from corn cob has potential application as a filler prepared by hydrolysis process using a strong acid. The producing of natural rubber latex films through coagulant dowsing process. This research started with the pre-vulcanization process of natural rubber latex at 70 °C and followed by process of vulcanization at 110 °C for 20 minutes. Natural rubber latex films that have been produced continued with the aging treatment at 70 °C for 168 hours. The mechanical properties of natural rubber latex films after aging treatment are the tensile strength, elongation at break, M100 and M300 have performed.

EFFECT OF THE PHASE STRUCTURE EVOLUTION ON THE PROPERTIES OF FILMS FORMED FROM PBA/P(ST-CO-MMA)COMPOSITE LATEX

Institute of Scientific and Technical Information of China (English)

无

2008-01-01

A group of heterogeneous latexes poly(butyl acrylate)/poly(styrene-co-methyl methacrylate)(PBA/P(St-co-MMA))were prepared by a semi-continuous seeded emulsion polymerization process under monomer starved conditions.The glass transition temperature(Tg)and the mechanical properties of the film formed from the composite latex changed with the evolution of the particle morphology.A photon transmission method was used to monitor the phase structure evolution of films which were prepared from core-shell PBA/P(St-co-MMA)latex at room temperature and annealed at 383 K above Tg of the polymers.In addition,the changes of the surface of the film formed from the composite latex with time at 383 K were observed by AFM.The evidence illustrated that the film formed from the core-shell latex particles was metastable.The rearrangement of the phases could occur under proper conditions.

Characteristics of Red Algae Bioplastics/Latex Blends under Tension

Directory of Open Access Journals (Sweden)

M. Nizar Machmud

2013-10-01

Full Text Available Cassava, corn, sago and the other food crops have been commonly used as raw materials to produce green plastics. However, plastics produced from such crops cannot be tailored to fit a particular requirement due to their poor water resistance and mechanical properties. Nowadays, researchers are hence looking to get alternative raw materials from the other sustainable resources to produce plastics. Their recent published studies have reported that marine red algae, that has been already widely used as a raw material for producing biofuels, is one of the potential algae crops that can be turned into plastics. In this work, Eucheuma Cottonii, that is one of the red alga crops, was used as raw material to produce plastics by using a filtration technique. Selected latex of Artocarpus altilis and Calostropis gigantea was separately then blended with bioplastics derived from the red algae, to replace use of glycerol as plasticizer. Role of the glycerol and the selected latex on physical and mechanical properties of the red algae bioplastics obtained under a tensile test performed at room temperature are discussed. Tensile strength of some starch-based plastics collected from some recent references is also presented in this paperDoi: 10.12777/ijse.5.2.81-88 [How to cite this article: Machmud, M.N., Fahmi, R.,  Abdullah, R., and Kokarkin, C.  (2013. Characteristics of Red Algae Bioplastics/Latex Blends under Tension. International Journal of Science and Engineering, 5(2,81-88. Doi: 10.12777/ijse.5.2.81-88

Production of Spirulina sp by utilization of wastewater from the powder type energy drinks

Science.gov (United States)

Sumantri, Indro; Priyambada, Ika Bagus

2015-12-01

Wastewater of energy drink type of powder produced when the the production equipment required cleaning treatment to produce one taste to others. These equipments washed by water, so that, it produced wastewater. It contains high organic substances and classified as high degradable due to food product. The content of wastewater is high carbon and nitrogen substances. Microalgae is an autotrophic microorganism, live without carbon presence, utilized to digest the substances in wastewater especially for nitrogen substances. Spirulina sp is the type of microalgae selected to utilize the wastewater of energy drink, the selection criteria is the size of Spirulina sp is relatively large and easy to separated from its solution. The experiment conducted by cultivate the seeding microalgae with certain nutrients until the certain volume. The synthetic wastewater obtained from one of energy drink type of powder with commercial brand as Kuku Bima Ener-G, the wastewater concentration selected under the close to the real condition of wastewater as basis of COD measurement (6 sachet/L or COD of 12.480mg/L) and aqueous concentration (1 sachet/L or COD of 2080mg/L). The batch experiments with 1L volume conducted and with variable of percent volume of wastewater added in order to observe the growth of microlagae. The response of the microalgae growth obtained by increasing the optical density of the microalgae solution and continued by calculation for the growth rate of microalgae. The result of the experiments indicated that for the aqueous concentration (1 sachet/L or COD of 2080mg/L) the optimum added of wastewater is 40 % with growrate of 0.55/day while for the concentrated wastewater (6 sachet/L or COD of 12.480mg/L), the optimum condition is 25 % wastewater added with growth rate of 0.43/day.

LaTeX - Know what you are missing

Directory of Open Access Journals (Sweden)

Gunther Maier

2016-11-01

Full Text Available This article gives a brief introduction to \\LaTeX\\ and related tools. The aim is to give an overview, to demonstrate the flexibility and versatility of the software, and to assist the reader taking first steps using it. The article links to a number of valuable resources for further information.

Radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Wan Manshol bin Wan Zin; Norjanah binti Mohid

1994-01-01

This paper describes the experimental techniques and the results of radiation vulcanization of natural rubber latex carried out on several high ammonia latices available in the country. The efficiency of various sensitisers and stabilisers used were evaluated in terms of the gamma radiation dose required to produce the maximum tensile strengths. The extent of crosslinking of RVNRL sample films were estimated by equilibrium swelling ratio measurements. The stability of pre-irradiated and post-irradiated samples were monitored using viscosity measurements as the parameter

Marine bacterial prodigiosin as dye for rubber latex, polymethyl ...

African Journals Online (AJOL)

Prodigiosin is known for its immunomodulatory, antibacterial, antimycotic, antimalarial, algicidal and anticancer activities. Here, we reported the evaluation of prodigiosin pigment as a dyeing agent in rubber latex, paper and polymethyl methacrylate (PMMA) so that it can be considered as an alternative to synthetic pigments.

Assessment of adverse reactions to latex gloves use among nurses ...

African Journals Online (AJOL)

... to latex is a common problem among nurses and other health care workers. ... There was significant association between family history and occurrence of ... These effects may vary in severity from skin problems to anaphylactic shock.

Dynamics of Nutrients Transport in Onsite Wastewater Treatment Systems

Science.gov (United States)

Toor, G.; De, M.

2013-05-01

Domestic wastewater is abundant in nutrients¬ that originate from various activities in the households. In developed countries, wastewater is largely managed by (1) centralized treatment where wastewater from large population is collected, treated, and discharged and (2) onsite treatment where wastewater is collected from an individual house, treated, and dispersed onsite; this system is commonly known as septic system or onsite wastewater treatment system (OWTS) and consist of a septic tank (collects wastewater) and drain-field (disperses wastewater in soil). In areas with porous sandy soils, the transport of nutrients from drain-field to shallow groundwater is accelerated. To overcome this limitation, elevated disposal fields (commonly called mounds) on top of the natural soil are constructed to provide unsaturated conditions for wastewater treatment. Our objective was to study the dynamics of nitrogen (N) and phosphorus (P) transport in the vadose zone and groundwater in traditional and advanced OWTS. Soil water samples were collected from the vadose zone by using suction cup lysimeters and groundwater samples were collected by using piezometers. Collected samples (wastewater, soil-water, groundwater) were analyzed for various water quality parameters. The pH (4.39-4.78) and EC (0.28-0.34 dS/m) of groundwater was much lower than both wastewater and soil-water. In contrast to >50 mg/L of ammonium-N in wastewater, concentrations in all lysimeters (0.02-0.81 mg/L) and piezometers (0.01-0.82 mg/L) were 99% disappeared (primarily nitrified) in the vadose zone (20 mg/L in the vadose zones of traditional systems (drip dispersal and gravel trench). Concentrations of chloride showed a distinct pattern of nitrate-N breakthrough in vadose zone and groundwater; the groundwater nitrate-N was elevated upto 19.2 mg/L after wastewater delivery in tradional systems. Total P in the wastewater was ~10 mg/L, but low in all lysimeters (0.046-1.72 mg/L) and piezometers (0.01-0.78 mg

Cryptosporidium and Giardia removal by secondary and tertiary wastewater treatment.

Science.gov (United States)

Taran-Benshoshan, Marina; Ofer, Naomi; Dalit, Vaizel-Ohayon; Aharoni, Avi; Revhun, Menahem; Nitzan, Yeshayahu; Nasser, Abidelfatah M

2015-01-01

Wastewater disposal may be a source of environmental contamination by Cryptosporidium and Giardia. This study was conducted to evaluate the prevalence of Cryptosporidium oocysts and Giardia cysts in raw and treated wastewater effluents. A prevalence of 100% was demonstrated for Giardia cysts in raw wastewater, at a concentration range of 10 to 12,225 cysts L(-1), whereas the concentration of Cryptosporidium oocysts in raw wastewater was 4 to 125 oocysts L(-1). The removal of Giardia cysts by secondary and tertiary treatment processes was greater than those observed for Cryptosporidium oocysts and turbidity. Cryptosporidium and Giardia were present in 68.5% and 76% of the tertiary effluent samples, respectively, at an average concentration of 0.93 cysts L(-1) and 9.94 oocysts L(-1). A higher detection limit of Cryptosporidium oocysts in wastewater was observed for nested PCR as compared to immune fluorescent assay (IFA). C. hominis was found to be the dominant genotype in wastewater effluents followed by C. parvum and C. andersoni or C. muris. Giardia was more prevalent than Cryptosporidium in the studied community and treatment processes were more efficient for the removal of Giardia than Cryptosporidium. Zoonotic genotypes of Cryptosporidium were also present in the human community. To assess the public health significance of Cryptosporidium oocysts present in tertiary effluent, viability (infectivity) needs to be assessed.

Microaerobic biodegradation of high organic load wastewater by ...

African Journals Online (AJOL)

USER

2010-06-21

Jun 21, 2010 ... concentration in the simulated wastewater as in the RCVBN medium. Optimization of wastewater composition and treatment conditions. SW with pollutants strength of 3600 mgl-1 COD was used to incubate the phototrophic bacteria microaerobically in the light (appro- ximately 2000 lx), the COD reduction ...

Formation of Defect-Free Latex Films on Porous Fiber Supports

KAUST Repository

Lively, Ryan P.; Mysona, Joshua A.; Chance, Ronald R.; Koros, William J.

2011-01-01

a defect-free lumen-side barrier layer can be created. Film experiments examined the effect of drying rate, latex age, substrate porosity (porous vs nonporous), and substrate hydrophobicity/ hydrophilicity. Film studies show that in ideal conditions

The construction and commissioning of MINT's latex irradiator

International Nuclear Information System (INIS)

Razali Hamzah; Muhd Khairi Muhd Said; Muhd Ariff Hamzah; Wan Manshol Wan Zin; Taiman Kadni

1996-01-01

The construction and installation of MINT's automatic continuous latex irradiator is described. MINT cooperated with NUKEM to design the plant. Construction was done by local building consultants and local contractor. The installation of the plant includes local fabrication components and imported components. The plant is automatically controlled by a computer system. Features of plant is described

Anaerobic biodegradation of a petrochemical waste-water using biomass support particles

International Nuclear Information System (INIS)

Sharma, S.; Ramakrishna, C.; Desai, J.D.; Bhatt, N.M.

1994-01-01

During the anaerobic biodegradation of effluent from a dimethyl terephthalate (DMT) manufacturing plant, reduction in chemical oxygen demand (COD) degradation and biogas formation was observed after the waste-water concentration exceeded 25% of added feed COD. This condition reverted back to normal after 25-30 days when the DMT waste-water concentration in the feed was brought down to a non-toxic level. However, the above effects were observed only after the concentration of DMT waste-water reached more than 75% of added feed COD when biomass support particles (BSP) were augmented to the system. In the BSP system, a biomass concentration of up to 7000 mg/l was retained and the sludge retention time increased to >200 days compared to 2200 mg/l and 8-10 days, respectively, in the system without BSP (control). Formaldehyde in the waste-water was found to be responsible for the observed toxicity. The BSP system was found to resist formaldehyde toxicity of up to 375 mg/l as against 125 mg/l in the control system. Moreover, the BSP system recovered from the toxicity much faster (15 days) than the control (25-30 days). The advantages of the BSP system in anaerobic treatment of DMT waste-water are discussed. (orig.)

[Electricity generation from sweet potato fuel ethanol wastewater using microbial fuel cell technology].

Science.gov (United States)

Cai, Xiao-Bo; Yang, Yi; Sun, Yan-Ping; Zhang, Liang; Xiao, Yao; Zhao, Hai

2010-10-01

Air cathode microbial fuel cell (MFC) were investigated for electricity production from sweet potato fuel ethanol wastewater containing 5000 mg/L of chemical oxygen demand (COD). Maximum power density of 334.1 mW/m2, coulombic efficiency (CE) of 10.1% and COD removal efficiency of 92.2% were approached. The effect of phosphate buffer solution (PBS) and COD concentration on the performance of MFC was further examined. The addition of PBS from 50 mmol/L to 200 mmol/L increased the maximum power density and CE by 33.4% and 26.0%, respectively. However, the COD removal efficiency was not relative to PBS concentration in the wastewater. When the COD increased from 625 mg/L to 10 000 mg/L, the maximum value of COD removal efficiency and the maximum power density were gained at the wastewater strength of 5 000 mg/L. But the CE ranged from 28.9% to 10.3% with a decreasing trend. These results demonstrate that sweet potato fuel ethanol wastewater can be used for electricity generation in MFC while at the same time achieving wastewater treatment. The increasing of PBS concentration can improve the power generation of MFC. The maximum power density of MFC increases with the rise of COD concentration, but the electricity generation will decrease for the acidification of high wastewater concentration.

Mechanical and Permeability Characteristics of Latex-Modified Pre-Packed Pavement Repair Concrete as a Function of the Rapid-Set Binder Content

Directory of Open Access Journals (Sweden)

Jae-Woong Han

2015-10-01

Full Text Available We evaluated the strength and durability characteristics of latex-polymer-modified, pre-packed pavement repair concrete (LMPPRC with a rapid-set binder. The rapid-set binder was a mixture of rapid-set cement and silica sand, where the fluidity was controlled using a latex polymer. The resulting mix exhibited a compressive strength of ¥21 MPa and a flexural strength of ¥3.5 MPa after 4 h of curing (i.e., the traffic opening term for emergency repairs of pavement. The ratio of latex polymer to rapid-set binder material was varied through 0.40, 0.33, 0.29, and 0.25. Mechanical characterization revealed that the mechanical performance, permeability, and impact resistance increased as the ratio of latex polymer to rapid-set binder decreased. The mixture exhibited a compressive strength of ¥21 MPa after 4 h when the ratio of latex polymer to rapid-set binder material was ¤0.29. The mixture exhibited a flexural strength of ¥3.5 MPa after 4 h when the ratio of latex polymer to rapid-set binder material was ¤0.33. The permeability resistance to chloride ions satisfied 2000 C after 7 days of curing for all ratios. The ratio of latex polymer to rapid-set binder material that satisfied all conditions for emergency pavement repair was ¤0.29.

A cost-benefit analysis of methods for the determination of biomass concentration in wastewater treatment.

Science.gov (United States)

Hernandez, J E; Bachmann, R T; Edyvean, R G J

2006-01-01

The measurement of biomass concentration is important in biological wastewater treatment. This paper compares the accuracy and costs of the traditional volatile suspended solids (VSS) and the proposed suspended organic carbon (SOC) methods. VSS and SOC values of a dilution system were very well correlated (R(2)=0.9995). VSS and SOC of 16 samples were determined, the mean SOC/VSS ratio (0.52, n=16, sigma=0.01) was close to the theoretical value (0.53). For costing analysis, two hypothetical cases were analysed. In case A, it is assumed that 108 samples are analysed annually from two continuous reactors. Case B represents a batch experiment to be carried out in 24 incubated serum bottles. The savings, when using the SOC method, were 11,987 pounds for case A and 90 pounds for case B. This study suggests the use of SOC method as a time saving and lower cost biomass concentration measurement.

Study of glucoamylase immobilization in butadiene nitrile latex membrane

International Nuclear Information System (INIS)

Miller, E.

1992-01-01

Attempts have been undetaken to immobilize glucoamylaze by means of butadiene nitrile latex in the presence of a chemical initiator and 60 Co γ-radiation. The activity, stability of conjugates in the membrane and permeability of oxygen in these membranes were determined. (author) 14 refs.; 5 figs

Prevalence and clinical impact of sensitization to latex and fruits in dentistry students at the University of Antioquia, and its relationship with allergy to fruits

Directory of Open Access Journals (Sweden)

Echenique Manrique, Alejandro

2015-04-01

Full Text Available Objective: To determine the prevalence and clinical impact of sensitization to latex and to five tropical fruits (banana, avocado, kiwi, pineapple and passion fruit in dentistry students. Methods: Analytical cross-sectional study of 128 dentistry students at University of Antioquia in Medellín, Colombia. Information was collected by means of a questionnaire and skin prick tests with latex and fruits were done. Results: All students reported having had contact with latex. Nine of them informed at least one episode of adverse reaction to contact with latex without proof of sensitization to it. Five reported at least one reaction with one of the fruits, but skin prick tests were negative. Four of the 14 students who reported gastrointestinal symptoms were sensitized to latex or to one of the tested fruits. Overall, latex sensitization rate was 3.1%. Conclusion: This percentage of sensitization to latex is lower than that in other studies; this may be due to the expression of immune mechanisms other than IgE mediation. We failed to demonstrate a higher sensitization rate to latex as students advanced in their career. The association between gastrointestinal symptoms and sensitization to both fruit and latex is to be emphasized.

Using natural zeolites to improve anaerobic abattoir wastewater treatment

International Nuclear Information System (INIS)

Diaz-Jimenez, L.; Herrera-Ramirez, E.; Carlos Hernandez, S

2009-01-01

Slaughterhouse wastewater have high concentrations of soluble and insoluble organics which represents environmental troubles, E. G. de oxygenation of rivers, underground water contamination. Anaerobic digestion is an efficient process for wastewater treatment. Performance are increased using microorganisms supported on porous solids. (Author)

Using natural zeolites to improve anaerobic abattoir wastewater treatment

Energy Technology Data Exchange (ETDEWEB)

Diaz-Jimenez, L.; Herrera-Ramirez, E.; Carlos Hernandez, S

2009-07-01

Slaughterhouse wastewater have high concentrations of soluble and insoluble organics which represents environmental troubles, E. G. de oxygenation of rivers, underground water contamination. Anaerobic digestion is an efficient process for wastewater treatment. Performance are increased using microorganisms supported on porous solids. (Author)

Cost evaluation of radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Makuuchi, K.

2003-01-01

Cost of radiation vulcanized NR latex was evaluated. The plant would be built in an existing dipping factory in an industrial area in a Southeast Asian country. One thousands dry tons of NR latex are vulcanized with a low energy electron accelerator. The electron accelerator is a self-shielding low energy type. The maximum accelerating voltage is 300 kV and the output power is 10 kW. The total construction cost of the plant is $400,000 including electron accelerator and other equipments. Costs of raw materials and utilities are $1.165 and $0.023 per one kg of product, respectively. The fixed costs of the plant consist of labor costs, labor overhead, maintenance, plant overhead, depreciation, and bank interest. It is $0.190/kg of product. The company overhead for operation including company management, R and D and insurance is $0.044/kg of product. Thus, the total production cost is estimated to be $1.422/kg of product. (author)

Review of wastewater problems and wastewater-management planning in the San Francisco Bay region, California

Science.gov (United States)

Hines, Walter G.

1973-01-01

The San Francisco Bay region has suffered adverse environmental effects related to the discharge of municipal-, industrial-, and agricultural- wastewater and storm-water runoff. Specific pollutional properties of theses discharges are not well understood in all cases although the toxic materials and aquatic-plant nutrients (biostimulants) found in municipal and industrial waterwater are considered to be a major cause of regional water-quality problems. Other water-quality problems in the region are commonly attributed to pesticides found in agricultural wastewater and potentially pathogenic bacteria in municipal-wastewater discharges and in storm-water runoff. The geographical distribution and magnitude of wastewater discharges in the bay region, particularly those from municipalities and industries, is largely a function of population, economic growth, and urban development. As might be expected, the total volume of wastewater has increased in a trend paralleling this growth and development. More significant, perhaps, is the fact that the total volume parameters such as BOD (biochemical oxygen demand), biostimulant concentrations, and toxicity, has increased despite large expenditures on new and improved municipal- and industrial-wastewater-treatment plants. Also, pollutant loadings from other major source, such as agriculture and storm-water runoff, have increased. At the time of writing (1972), many Federal, State, regional, and local agencies are engaged in a comprehensive wastewater-management-planning effort for the entire bay region. Initial objectives of this planning effort are: (1) the consolidation and coordination of loosely integrated wastewater-management facilities and (2) the elimination of wastewater discharges to ecologically sensitive areas, such as fresh-water streams and shallow extremities of San Francisco Bay. There has been some investigation of potential long-range wastewater-management alternatives based upon disposal in deep water in the

Preliminary Study on the Effect of Wastewater Storage in Septic Tank on E. coli Concentration in Summer

OpenAIRE

Appling, Dominique; Habteselassie, Mussie; Radcliffe, David; Bradshaw, James

2013-01-01

On-site wastewater treatment systems (OWTS) work by first storing the wastewater in a septic tank before releasing it to soils for treatment that is generally effective and sustainable. However, it is not clear how the abundance of E. coli changes during its passage through the tank. In this study, which was conducted under the UGA young Scholar Program in summer of 2010, we examined the change in wastewater quality parameters during the passage of the wastewater through the tank and after it...

Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

Energy Technology Data Exchange (ETDEWEB)

Karim, Ahmad Fikri Abdul, E-mail: a.fikri-89@yahoo.com; Ariff, Zulkifli Mohamad [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Pulau Pinang (Malaysia); Ismail, Hanafi [Cluster for Polymer Composites (CPC), Science and Engineering Research Centre, Engineering Campus, Universiti Sains Malaysia,14300 Nibong Tebal, Pulau Pinang (Malaysia)

2015-07-22

This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed by using scanning electron microscopy (SEM)

Mechanical and morphological properties of kenaf powder filled natural rubber latex foam

International Nuclear Information System (INIS)

Karim, Ahmad Fikri Abdul; Ariff, Zulkifli Mohamad; Ismail, Hanafi

2015-01-01

This research is carried out by incorporate kenaf powder with natural rubber latex (NRL) compound and is foamed to make natural rubber latex foam (NRLF) by using a well known technique called Dunlop method. Different loading of kenaf powder was added to NRL compound and was foamed to make NRLF. The tensile properties, and morphology of kenaf filled NRLF was studied. Increase in kenaf loading reduced the tensile strength and elongation at break and of a compound. Modulus at 100% elongation of the compound increased with increased in filler loading. The morphological and micro structural characterization has been performed by using scanning electron microscopy (SEM)

A LaTeX graphics routine for drawing Feynman diagrams

International Nuclear Information System (INIS)

Levine, M.J.S.

1990-01-01

FEYNMAN is a LaTeX macropackage which allows the user to construct a versatile range of Feynman diagrams within the text of a document. Diagrams of publication quality may be drawn with relative ease and rapidity. (orig.)

Investigations into the biodegradation of microcystin-LR in wastewaters

International Nuclear Information System (INIS)

Ho, Lionel; Hoefel, Daniel; Palazot, Sebastien; Sawade, Emma; Newcombe, Gayle; Saint, Christopher P.; Brookes, Justin D.

2010-01-01

Microcystins are potent hepatotoxins that can be produced by cyanobacteria. These organisms can proliferate in wastewaters due to a number of factors including high concentrations of nutrients for growth. As treated wastewaters are now being considered as supplementary drinking water sources, in addition to their frequent use for irrigated agriculture, it is imperative that these wastewaters are free of toxins such as microcystins. This study investigated the potential for biodegradation of microcystin-LR (MCLR) in wastewaters through a biological sand filtration experiment and in static batch reactor experiments. MCLR was effectively removed at a range of concentrations and at various temperatures, with degradation attributed to the action of microorganisms indigenous to the wastewaters. No hepatotoxic by-products were detected following the degradation of MCLR as determined by a protein phosphatase inhibition assay. Using TaqMan polymerase chain reaction, the first gene involved in bacterial degradation of MCLR (mlrA) was detected and the responsible bacteria shown to increase with the amount of MCLR being degraded. This finding suggested that the degradation of MCLR was dependent upon the abundance of MCLR-degrading organisms present within the wastewater, and that MCLR may provide bacteria with a significant carbon source for proliferation; in turn increasing MCLR removal.

Heat recovery from wastewater systems; Waermerueckgewinnung aus Abwassersystemen

Energy Technology Data Exchange (ETDEWEB)

Wanner, O.

2004-07-01

Wastewater contains large amounts of heat energy which can be recovered by means of a heat pump and a heat exchanger installed in the sewer system. Practical problems, which may arise and have been investigated in this research project, are the reduction of the heat transfer efficiency due to heat exchanger fouling and the reduction of the nitrification capacity of downstream wastewater treatment plants due to lower wastewater temperatures. A mathematical model was developed by which the decrease of the wastewater temperature in the treatment plant influent can be determined as a function of the amount of heat energy gathered from the wastewater in the sewer system. By this model the variation in time and space of the wastewater temperature in a sewer pipe is calculated for given hydraulics, geometry and environmental conditions. By analysis of data from a large wastewater treatment plant and simulations with a calibrated model, the effect of lowered influent temperatures on nitrification safety, total nitrogen removal efficiency and ammonium effluent concentrations could be quantified. A procedure is suggested by which the reserve nitrification capacity of an existing treatment plant and the increase of the ammonium effluent concentration resulting from a permanent decrease of the wastewater influent temperature can be estimated. By experiments with a pilot scale heat exchanger in a small wastewater channel, the significance of parameters known to have an effect on fouling was investigated and measures to reduce fouling were tested. The measures tested included controlled variation of the wastewater flow velocity (flushing), coatings and finish of the heat exchanger surface and obstacles mounted on the surface. The best results were obtained by regular short term increases of the flow velocity. By this measure, the efficiency of the fouled heat exchanger, which on the average was 60% of the efficiency of the clean heat exchanger, could repeatedly be raised to an

Green mediated synthesis and characterization of ZnO nanoparticles using Euphorbia Jatropa latex as reducing agent

Directory of Open Access Journals (Sweden)

M.S. Geetha

2016-09-01

Full Text Available Presently the progress of green chemistry in the synthesis of nanoparticles with the use of plants has engrossed a great attention. This study reports the synthesis of ZnO using latex of Euphorbia Jatropa as reducing agent. As prepared product was characterized by powder X-ray diffractometer (PXRD, Fourier transform infra-red spectroscopy (FTIR, scanning electron microscopy–energy dispersive spectroscopy (SEM–EDS, transmission electron microscopy (TEM, X-ray photo electron spectroscopy (XPS, Rietveld refinement, UV–Visible spectroscopy and photoluminescence (PL. The concentration of plant latex plays an important role in controlling the size of the particle and its morphology. PXRD graphs showed the well crystallisation of the particles. The average particle size was calculated using Scherrer equation and advanced Williamson Hall (WH plots. The average particle size was around 15 nm. This result was also supported by SEM and TEM analyses. FTIR shows the characteristic peak of ZnO at 435 cm−1. SEM and TEM micrographs show that the particles were almost hexagonal in nature. EDS of SEM analysis confirmed that the elements are only Zn and O. EDS confirmed purity of ZnO. Atomic states were confirmed by XPS results. Crystal parameters were determined using Rietveld refinement. From UV–Visible spectra average energy gap was calculated which is ∼3.63 eV. PL studies showed UV emission peak at 392 nm and broad band visible emission centred in the range 500–600 nm. The Commission International de I'Eclairage and colour correlated temperature coordinates were estimated for ZnO prepared using 2 ml, 4 ml and 6 ml Jatropa latex. The results indicate that the phosphor may be suitable for white light emitting diode (WLED. The study fruitfully reveals simple, fast, economical and eco friendly method of synthesis of multifunctional ZnO nanoparticles (Nps.

Conceptual design for treatment of mining and metallurgical wastewaters which contains arsenic and antimony

Directory of Open Access Journals (Sweden)

Željko Kamberović

2012-12-01

Full Text Available This paper presents a preliminary design for treatment of mining and metallurgical wastewaters (MMW from the basin of antimony “Zajača“, which contains high concentrations of arsenic and antimony. MMW have been investigated in laboratory, due to large difference in concentrations of pollutants. Metallurgical wastewaters were treated using iron (II-sulfate and lime milk used to adjust the pH value at 7. After chemical treatment of metallurgical wastewater and its joining with mining wastewater, residual amount of arsenic in water was below maximum allowed concentrations, while the concentration of antimony, remained above the maximum allowed value. The final phase of purification process was performed using ion exchange resin. After treatment of MMW, they can be used as technical water in the smelting process of secondary raw lead materials.

Oil-Acrylic hybrid latexes as binders for waterborne coatings

NARCIS (Netherlands)

Hamersveld, E.M.S.; Es, van J.J.G.S.; German, A.L.; Cuperus, F.P.; Weissenborn, P.; Hellgren, A.C.

1999-01-01

The combination of the characteristics of oil, or alkyd, emulsions and acrylic latexes in a waterborne binder has been the object of various studies in the past. Strategies for combining the positive properties of alkyds, e.g. autoxidative curing, gloss and penetration in wood, with the fast drying

Oil-acrylic hybrid latexes as binders for waterborne coatings

NARCIS (Netherlands)

Hamersveld, van E.M.S.; Es, van J.; German, A.L.; Cuperus, F.P.; Weissenborn, P.; Hellgren, A.C.

1999-01-01

The combination of the characteristics of oil, or alkyd, emulsions and acrylic latexes in a waterborne binder has been the object of various studies in the past. Strategies for combining the positive properties of alkyds, e.g. autoxidative curing, gloss and penetration in wood, with the fast drying

Latex allergy in an infant with acquired hydrocephalus | Ehiozw ...

African Journals Online (AJOL)

We report the case of a 3 month old male infant with acquired hydrocephalus undergoing ventriculo-peritoneal shunt insertion who developed wheals and suffered a respiratory arrest following contact with latex gloves. The need for anaesthetists to effectively diagnose and properly manage this rare clinical entity is ...

Surfactant and counter-ion distribution in styrene-butyl acrylate-acrylic acid dry latex submonolayers

Directory of Open Access Journals (Sweden)

Keslarek Amauri José

2004-01-01

Full Text Available Styrene-butyl acrylate-acrylic acid latex submonolayers prepared using a non-reactive phosphate surfactant together with a reactive sulfonate surfactant were examined in a transmission microscope using electron energy loss spectroscopy imaging (ESI-TEM. Phosphorus is nearly absent from the particles core but it is detected in a thick shell and in unusual, strongly scattering structures with a low carbon content, and largely made out of inorganic phosphate. P is also dispersed outside the particles, while S is uniformly distributed within then. The Na and N elemental maps show that the respective monovalent ions (Na+ and NH4+ have different distributions, in the latex: Na signal within the particles is stronger than in the background, while N is accumulated at the particle borders. The distributions of surfactant and counter-ions are thus different from some current assumptions, but they support recent results on the distribution of ionic constituents in latex films, by scanning electric potential microscopy.

Extraction and comparison of proteins from natural rubber latex by conventional and ionizing radiation methods

International Nuclear Information System (INIS)

Rogero, Sizue O.; Spencer, Patrick J.; Campos, Vania E.; Lusvarghi, Fabio M.; Higa, Olga Z.

1997-01-01

Several proteins in natural rubber latex (NRL) have been assigned to be significant allergens. It is known that proteins submitted to ionizing radiation suffer denaturation and immunochemical modification resulting in low antigenic reactivity. The aim of this study was to extract and compare water extractable proteins from NRL films vulcanized by conventional and by ionizing radiation methods. SDS-polyacrylamide gel electrophoresis (SDS--PAGE) and high pressure liquid chromatography (HPLC) showed a diffuse protein band of about 14 KDa, which we believe is rubber elongation factor (REF), in both eluates, but smaller in latex film vulcanized by ionizing radiation. REF has been suggested to be a major latex allergen. These data suggest that ionizing radiation vulcanization could be an useful method for the production of NRL goods with low antigenicity. (author). 8 refs., 2 figs., 1 tab

The polymerization of aniline in polystyrene latex particles

Czech Academy of Sciences Publication Activity Database

Blinova, Natalia V.; Reynaud, S.; Roby, F.; Trchová, Miroslava; Stejskal, Jaroslav

2010-01-01

Roč. 160, 15/16 (2010), s. 1598-1602 ISSN 0379-6779 R&D Projects: GA AV ČR IAA400500905; GA ČR GA203/08/0686; GA ČR GA202/09/1626 Institutional research plan: CEZ:AV0Z40500505 Keywords : polyaniline * polystyrene latex * polyaniline-polystyrene composite Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.871, year: 2010

Acetylcholinesterase Inhibitory and Antioxidant Properties of Euphorbiacharacias Latex

Directory of Open Access Journals (Sweden)

Francesca Pintus

2013-03-01

Full Text Available The aim of the present study was to evaluate the acetylcholinesterase inhibitory capacity and the antioxidant properties of extracts of Euphorbia characias latex, a Mediterranean shrub. We performed a new extraction method involving the use of the trichloroacetic acid. The extract showed high antioxidant activity, was rich in total polyphenolic and flavonoid content and exhibited substantial inhibition of acetylcholinesterase activity.

Phenol Removal from Industrial Wastewater by HRP Enzyme

Directory of Open Access Journals (Sweden)

Iran Alemzadeh

2009-01-01

Full Text Available In this research, horseradish peroxidase for phenol removal was utilized. First, the process was studied at the laboratory scale using a synthetic phenol solution (1-10 mM. Results showed that horseradish peroxidase (HRP could effectively remove phenolic compounds from wastewater and that the catalytic capability of the enzyme was maintained for a wide range of pH, temperature, and aromatic concentration levels. The performance conditions were optimized for at lease 95% and 100% removal of phenolic compounds for both actual and synthetic wastewaters under high and low phenol concentrations (1 and 10 mM. The phenolic wastewater used was an olive mill effluent with a phenol concentration of 1221 mg/L (13 mM and a pH value of 3.5. At the end of the reaction, the phenolic compounds changed to insoluble polymers and precipitated. Each enzyme/wastewater system was optimized for the following chemical dosages: hydrogen peroxide, enzyme, polyethylene glycol (PEG, and buffer. Furthermore, the reaction time to achieve at least 95% phenol removal was determined. According to the results, COD and BOD reduced to 58% and 78%, respectively. Experimental results showed an increase in H2O2 concentration beyond the optimum dose resulting from enzyme inactivation, thus reducing the phenol removal efficiency. On the other hand, increasing the enzyme, PEG, and/or reaction time beyond the optimum values resulted in only a marginal increase in removal efficiency.

Type I allergy to natural rubber latex and type IV allergy to rubber chemicals in health care workers with glove-related skin symptoms.

Science.gov (United States)

Nettis, E; Assennato, G; Ferrannini, A; Tursi, A

2002-03-01

It has been established that there are type I and type IV allergens in latex gloves. The purpose of the study was to establish the prevalence of rubber glove-induced skin symptoms among health care workers in one Italian hospital. Health care workers (n = 1584) were evaluated using a written questionnaire and 295 respondents with glove-induced skin symptoms were tested. We performed: skin prick test with latex glove extract and commercial latex, and environmental and food allergens; glove use test; patch tests with a rubber additive series; and RASTs. Hospital employees who used or had used latex gloves at work were 1294. Three hundred and sixteen (24.4%) reported glove-induced symptoms, namely, cutaneous symptoms in all the cases and non-cutaneous symptoms in 105 subjects (8.1%). Twenty-seven of the 295 symptomatic employees tested (9.1%) were latex sensitive. Thirty-one patients (10.5%) exhibited positive patch test to rubber-related allergens. The most positive readings were obtained from the Thiuram mix and the Carba mix, with 12 and 9 positivities, respectively. The risk factors for latex skin sensitization were: a previous history of atopy and asthma; history of surgery; pre-existing hand dermatitis; work-related symptoms; and positive skin tests to common inhalant and certain foods (P skin complaints of latex gloves are related to skin irritation rather than to allergy. The immediate allergy to latex and the delayed allergy to rubber chemicals suggest that all the health care workers with glove-related dermatitis should undergo both skin prick test and glove use test to detect type I hypersensitivity to latex, and patch test to detect type IV hypersensitivity to rubber chemicals.

Removal of Lead from Wastewater Contaminated with Chemical Synthetic Dye by Aspergillus terreus

Directory of Open Access Journals (Sweden)

Lamyai Neeratanaphan

2015-07-01

Full Text Available Novel isolated microorganisms have been demonstrated to efficiently remove lead from wastewater contaminated with chemical synthetic dye. In this study, the physical and chemical parameters of wastewater samples (including Pb concentrations were analyzed before and after treatment with microorganisms. The highest Pb concentration detected in wastewater was 0.788 mg/l. Investigations of the Pb tolerance and removal capacities of microorganism strains isolated from the wastewater sediment resulted in the selection of three fungal isolates (F102, F203 and F302. Interestingly, isolate F203 had a Pb tolerance of up to 100 mg/l. Using DNA barcoding and morphological characteristics, fungal isolate F203 was identified as Aspergillus terreus. Wastewater characteristics before treatment included a grayish black color with pH, TDS, BOD, COD and Pb concentrations higher than the Thailand standard values. Wastewater qualities after treatment with A. terreus showed definite improvement; however, the values of certain parameters were still higher than the allowed values based on the Thailand standard. The only improvement that fell within the allowed standard was the Pb concentration. Next, A. terreus was used for Pb adsorption in wastewater with an initial Pb concentration of 0.788 mg/l at time points corresponding to 0, 24, 48, 72, 96, 120, 144 and 168 h of incubation. The results showed that A. terreus could adsorb and remove higher amounts of Pb from wastewater than the other fungal isolates. Time course adsorption analysis showed the remaining Pb concentrations as 0.788, 0.213, 0.162, 0.117, 0.100, 0.066, 0.042 and 0.032 mg/l, respectively; the percentage of Pb removal could be estimated as 0, 72.97, 79.44, 85.15, 87.31, 91.62, 94.67 and 95.94%, respectively. In conclusion, A. terreus possessed the ability to adsorb up to 96% of Pb from chemical synthetic dye within 168 h. Thus, A. terreus might be suitable for adaptation and use in Pb treatment.

Biosorption of hexavalent chromium in a tannery industry wastewater using fungi species

International Nuclear Information System (INIS)

Sivakumar, D.

2016-01-01

The isolated fungi species of different kinds from chromium contaminated soil sites located in Nagalkeni, Chennai were used for reducing chromium(VI) in a tannery industry wastewater of Nagalkeni, Chennai. The experiments were conducted to know biosorption potential of isolated fungi species for removing chromium(VI) in a tannery industry wastewater against the different p H, fungi biomass and chromium(VI) concentration (dilution ratio). The results of this study indicated that the order of maximum removal of chromium(VI) by an isolated fungi species at an optimum pH of 3, fungi biomass of 4g and an initial chromium(VI) concentration of 18.125 mg/L (dilution ratio 4) is A. niger > A. flavus > A. fumigatus > A. nidulans > A. heteromorphus > A. foetidus > A. viridinutans. This study found that the maximum removal of chromium(VI) was achieved by Aspergillus niger (96.3 %) than other fungi species at chromium(VI) concentration of 18.125 mg/L in a tannery industry wastewater. The chromium removal from tannery industry wastewater was validated by checking chromium removal in an aqueous solution and by checking the removal efficiency of other parameters in a tannery industry wastewater using same isolated A. niger. Biosorption model was proposed to simulate the experimental condition for removing chromium(VI) in a tannery industry wastewater by all isolated fungi species. The R2 and x2 values of the proposed model predicted that the proposed biosorption model is very much useful for predicting the trend of reduction potential of chromium(VI) in a tannery industry wastewater by all isolated fungi species. This study suggested that one could select the type of fungi species, ion concentration level, selection of treatment period, quantity of biomass to be used, and p H level of the medium, to achieve the highest reduction of any toxic metals from any contaminated water, wastewater and soil environment.

Treatment of marine sewage pumpout and RV park pumpout wastewater containing high strength concentrations of formaldehyde

International Nuclear Information System (INIS)

Salonich, J.

2002-01-01

'Full text:' A consortium of companies has developed an integrated 'on-site' wastewater treatment technology that is capable of handling and degrading RV Park and Marine Sewage Pumpout Wastes which contain formaldehyde [35 - 80 mg/L]. Boat and RV owners add formaldehyde to their toilets to eliminate odors. When these materials are pumped out they are high in solids content and have high concentrations of HCHO, which makes them difficult to degrade at POTWs. At the heart of this process is 1. An aeration tank with a Venturi Aerator totally external to the tank and 2. The addition of a blend of cultured bacteria that have selected for their ability to degrade formaldehyde. For a complete 'on-site' treatment system Bioclere Trickling Filters can follow this aeration/bacterial treatment system. This is an ideal system configuration for remote locations (RV Parks) or for fresh water lake Marinas looking to reduce their disposal costs and for groundwater discharge with no adverse effect on water quality. Until the development of the formaldehyde degrading bacteria for an industrial wastewater process there were no cultures commercially available specifically for degrading formaldehyde. The most commonly used bacteria were pseudomonas strains for carbohydrate or hydrocarbon wastewater extracted from activated sludge plants. And since formaldehyde is infinitely soluble in a liquid it is difficult to degrade or mineralize. The process in an activated sludge WWTP plant took over 72 hours. With the newly selected consortia of cultures, HCHO can be degraded in 12-14 hours on a batch basis. This is accomplished in a uniquely configured aeration tank where the 'environment' of the tank is constantly conditioned by a Venturi Aerator which strips carbon dioxide generated by the aerobes to maintain a neutral pH, and provide high levels of DO (>5.0 mg/L) to keep the process aerobic. (author)

Content of Asthmagen Natural Rubber Latex Allergens in Commercial Disposable Gloves.

Science.gov (United States)

Bittner, C; Garrido, M V; Krach, L H; Harth, V

The use of natural rubber latex (NRL) gloves in many occupations may lead to latex sensitization, allergic asthma, and skin reactions. Due to their good properties and environmental safety NRL gloves are still being used in the healthcare setting, but also in the food industry, by hairdressers, cleaners, etc. The aim of our study was to assess the protein and NRL allergen content in commercial gloves by different methods, including a new assay. Twenty commercially available NRL gloves were analyzed. Protein extraction was performed according to the international standard ASTM D-5712. Total protein content was measured with a modified Lowry method, NRL content with the CAP Inhibition Assay, the Beezhold ELISA Inhibition Assay, and an innovative ELISA with IgY-antibodies extracted from eggs of NRL-immunized hens (IgY Inhibition Assay). We found a high protein content in a range of 215.0-1304.7 μg/g in 8 out of the 20 NRL gloves. Seven of the 20 gloves were powdered, four of them with a high protein content. In gloves with high protein content, the immunological tests detected congruently high levels of NRL allergen. We conclude that a high percentage of commercially available NRL gloves still represent a risk for NRL allergy, including asthma. The modified Lowry Method allows to infer on the latex allergen content.

Define of internal recirculation coefficient for biological wastewater treatment in anoxic and aerobic bioreactors

Science.gov (United States)

Rossinskyi, Volodymyr

2018-02-01

The biological wastewater treatment technologies in anoxic and aerobic bioreactors with recycle of sludge mixture are used for the effective removal of organic compounds from wastewater. The change rate of sludge mixture recirculation between bioreactors leads to a change and redistribution of concentrations of organic compounds in sludge mixture in bioreactors and change hydrodynamic regimes in bioreactors. Determination of the coefficient of internal recirculation of sludge mixture between bioreactors is important for the choice of technological parameters of biological treatment (wastewater treatment duration in anoxic and aerobic bioreactors, flow capacity of recirculation pumps). Determination of the coefficient of internal recirculation of sludge mixture requires integrated consideration of hydrodynamic parameter (flow rate), kinetic parameter (rate of oxidation of organic compounds) and physical-chemical parameter of wastewater (concentration of organic compounds). The conducted numerical experiment from the proposed mathematical equations allowed to obtain analytical dependences of the coefficient of internal recirculation sludge mixture between bioreactors on the concentration of organic compounds in wastewater, the duration of wastewater treatment in bioreactors.

Trialed production of low protein irradiated natural rubber latex in factory scale by gamma irradiation technique

International Nuclear Information System (INIS)

Utama, Marga; Herwinarni, S.; Halik, H.M.; Siswanto; Suharyanto; Syamsu, Y.; Handoko, B.

2006-01-01

Four tons fresh field natural rubber latex (FNRL) with total solid content 30% were added with 2 phr (part hundred ratio of rubber) normal butyl acrylate (nBA) then irradiated by gamma rays at 25 kGy. The irradiated FNRL was centrifuged, then the properties of irradiated centrifuged natural rubber latex (INRL) and its film were measured before and after storage for 5 months. It is found that the INRL is stable latex during storage in 5 months, with lowest protein, and free nitrosamine content. The tensile strength of INRL film was 24-27 MPa, and modulus 600% was 1,5-2,0 MPa, elongation at break was 900%, and hardness was 27-29 Shore A, while the extractable protein content less than 100 μg/g. (author)

Morphologic evaluation of the use of a latex prosthesis in videolaparoscopic inguinoplasty: an experimental study in dogs Avaliação morfológica da utilização de prótese de latex na inguinoplastia videolaparoscópica: estudo experimental em cães

Directory of Open Access Journals (Sweden)

Luiz Henrique de Sousa

2011-01-01

Full Text Available PURPOSE: To evaluate the morphological aspects of the behavior of 4 types of latex biomembranes implanted in preperitoneal videolaparoscopic inguinoplasty. METHODS: Sixteen inguinoplasties were performed in 12 dogs: group 1 received an impermeable latex biomembrane in the right inguinal region and a prolene prosthesis, as control, in the contralateral inguinal region; groups 2, 3 and 4 received latex biomembranes respectively containing impermeable polyamide, 1-mm thick porous polyamide and 0.5-mm thick porous polyamide. Macro- and microscopic evaluations of the inguinal region and of the removed implants were made on the 7th, 14th, 21st and 28th days in group 1 and on the 28th postoperative day in the other groups. RESULTS: We observed absence of hematoma, seroma and infection; presence of tortuosities; induction of vascular neoformation, inflammatory reaction and collagen deposition, and full encystment of the latex biomembranes, except that with fine porous polyamide, which was partially incorporated, with the formation of microcysts. No latex biomembrane induced fibrosis as observed in the prolene control group. CONCLUSIONS: The biomembranes maintain induction of the healing process without fibrosis, are fully encysted and, except for the one with fine porous polyamide, are not incorporated into adjacent tissues. The latex biomembrane, with or without polyamide, is not recommended as a separate material for preperitoneal inguinoplasty.OBJETIVO: Avaliar aspectos morfológicos do comportamento de 4 tipos de biomembranas de latex, colocadas pré-peritonealmente em cães, por inguinoplastia videolaparoscópica. MÉTODOS: Dezesseis inguinoplastias em 12 cães: grupo 1, com biomembrana de latex impermeável inguinal direita em quatro cães e prótese de prolene, como controle, contra-lateral; grupos 2, 3 e 4, com biomembrana de latex respectivamente de poliamida impermeável, poliamida porosa com 1mm de espessura e poliamida porosa com 0,5mm de

Whole-transcriptome survey of the putative ATP-binding cassette (ABC) transporter family genes in the latex-producing laticifers of Hevea brasiliensis.

Science.gov (United States)

Zhiyi, Nie; Guijuan, Kang; Yu, Li; Longjun, Dai; Rizhong, Zeng

2015-01-01

The ATP-binding cassette (ABC) proteins or transporters constitute a large protein family in plants and are involved in many different cellular functions and processes, including solute transportation, channel regulation and molecular switches, etc. Through transcriptome sequencing, a transcriptome-wide survey and expression analysis of the ABC protein genes were carried out using the laticiferous latex from Hevea brasiliensis (rubber tree). A total of 46 putative ABC family proteins were identified in the H. brasiliensis latex. These consisted of 12 'full-size', 21 'half-size' and 13 other putative ABC proteins, and all of them showed strong conservation with their Arabidopsis thaliana counterparts. This study indicated that all eight plant ABC protein paralog subfamilies were identified in the H. brasiliensis latex, of which ABCB, ABCG and ABCI were the most abundant. Real-time quantitative reverse transcription-polymerase chain reaction assays demonstrated that gene expression of several latex ABC proteins was regulated by ethylene, jasmonic acid or bark tapping (a wound stress) stimulation, and that HbABCB15, HbABCB19, HbABCD1 and HbABCG21 responded most significantly of all to the abiotic stresses. The identification and expression analysis of the latex ABC family proteins could facilitate further investigation into their physiological involvement in latex metabolism and rubber biosynthesis by H. brasiliensis.

Optimization model for the design of distributed wastewater treatment networks

Directory of Open Access Journals (Sweden)

Ibrić Nidret

2012-01-01

Full Text Available In this paper we address the synthesis problem of distributed wastewater networks using mathematical programming approach based on the superstructure optimization. We present a generalized superstructure and optimization model for the design of the distributed wastewater treatment networks. The superstructure includes splitters, treatment units, mixers, with all feasible interconnections including water recirculation. Based on the superstructure the optimization model is presented. The optimization model is given as a nonlinear programming (NLP problem where the objective function can be defined to minimize the total amount of wastewater treated in treatment operations or to minimize the total treatment costs. The NLP model is extended to a mixed integer nonlinear programming (MINLP problem where binary variables are used for the selection of the wastewater treatment technologies. The bounds for all flowrates and concentrations in the wastewater network are specified as general equations. The proposed models are solved using the global optimization solvers (BARON and LINDOGlobal. The application of the proposed models is illustrated on the two wastewater network problems of different complexity. First one is formulated as the NLP and the second one as the MINLP. For the second one the parametric and structural optimization is performed at the same time where optimal flowrates, concentrations as well as optimal technologies for the wastewater treatment are selected. Using the proposed model both problems are solved to global optimality.

COD fractions changes in the SBR-type reactor treating municipal wastewater with controlled percentage of dairy sewage

Directory of Open Access Journals (Sweden)

Struk-Sokołowska Joanna

2017-01-01

Full Text Available The aim of study was to investigate the influence of percentage of dairy wastewater in the municipal wastewater on the changes of COD fractions during the cycle of SBR-type reactor. The scope of the research included physicochemical analyses of municipal wastewater without dairy wastewater, dairy wastewater, mixture of municipal and dairy wastewater as well as treated sewage. Both the concentrations and the proportions between COD fractions changed in the SBR cycle. In raw municipal and dairy wastewater - XS, insoluble hardly bio-degradable fraction of COD dominated (49.6 and 64.5% respectively. In treated wastewater SI, COD for dissolved compounds that are not biologically decomposed (inert (from 62.1 to 74.6% dominated, while XS fraction was from 19.1 to 24.4%. The consumption rate of organic compounds depended on the type of COD fraction, SBR cycle phase and the percentage of dairy wastewater. The highest rates of organic compounds consumption were noted in the phase of mixing. In the case of fraction SI, no differences in concentration in the SBR cycle time, were found. Concentration of COD in treated wastewater was from 34.8 to 58.9 mgO2·L-1 (efficiency wastewater treatment from 96.0 to 98.6%.

Growth of young Tabebuia aurea seedlings under irrigation with wastewater from fish farming

Directory of Open Access Journals (Sweden)

José R. de S. Pinto

2016-06-01

Full Text Available ABSTRACT This study aimed to evaluate the growth of young Tabebuia aurea seedlings irrigated with different concentrations of wastewater from fish farming. The experiment was conducted in a seedling nursery, from June to August 2013. The treatments consisted of five concentrations of wastewater from fish farming diluted in freshwater (0, 25, 50, 75 and 100% of wastewater. Plant height, stem diameter and plant height/stem diameter ratio were evaluated every 15 days to verify the effects of treatments on seedlings growth. At the end of the experiment, individual leaf area, leaf area, leaf dry matter, stem dry matter, root dry matter, total dry matter and Dickson quality index were also evaluated. The reuse of wastewater from fish farming diluted at concentrations of 25 and 50% in freshwater is a viable alternative in the production of Tabebuia aurea seedlings. However, higher concentrations hinder the production of seedlings of this species.

Removal of Chromium and Cadmium from Wastewater in Waste Stabilization Ponds, Yazd-Iran

Directory of Open Access Journals (Sweden)

Mohammad Reza Samaei

2016-04-01

Full Text Available Background: Heavy metals have destructive and irreversible effects on the human, plants and animals. Some industries in Yazd enter industrial wastewater to municipal wastewater collection system. This can lead to high levels of heavy metals in wastewater and in turn in the wastewater treatment plant effluent. Methods: This study was carried out during four months from December 22, 2009 to May 20, 2010. The experiment was performed on the inflow, outlet of anaerobic pond and first and second facultative ponds of wastewater treatment plant and then transferred to the laboratory and measured by atomic absorption spectroscopy. Results: The results of the experiments showed that the average cadmium concentrations in the inflow, anaerobic pond outlet, and first and second facultative pond outlet were 0.0066, 0.0087, 0.0076, and 0.0083μg/l, respectively. The average amounts of chromium in the inflow, anaerobic pond outlet, and first and second facultative pond outlet were 0.0076, 0.0065, 0.0043, and 0.0056 μg/l, respectively. Cadmium concentration in the effluent was higher than standard. Conclusion: The comparison of the obtained data with Iranian standards for wastewater treatment for reuse in irrigation shows that the cadmium concentration exceeded the standard and the chromium concentration was lower than the standard. Therefore, it is not suitable for reuse in the crop farms and aquatic life

Removal of phosphate from greenhouse wastewater using hydrated lime.

Science.gov (United States)

Dunets, C Siobhan; Zheng, Youbin

2014-01-01

Phosphate (P) contamination in nutrient-laden wastewater is currently a major topic of discussion in the North American greenhouse industry. Precipitation of P as calcium phosphate minerals using hydrated lime could provide a simple, inexpensive method for retrieval. A combination of batch experiments and chemical equilibrium modelling was used to confirm the viability of this P removal method and determine lime addition rates and pH requirements for greenhouse wastewater of varying nutrient compositions. Lime: P ratio (molar ratio of CaMg(OH)₄: PO₄‒P) provided a consistent parameter for estimating lime addition requirements regardless of initial P concentration, with a ratio of 1.5 providing around 99% removal of dissolved P. Optimal P removal occurred when lime addition increased the pH from 8.6 to 9.0, suggesting that pH monitoring during the P removal process could provide a simple method for ensuring consistent adherence to P removal standards. A Visual MINTEQ model, validated using experimental data, provided a means of predicting lime addition and pH requirements as influenced by changes in other parameters of the lime-wastewater system (e.g. calcium concentration, temperature, and initial wastewater pH). Hydrated lime addition did not contribute to the removal of macronutrient elements such as nitrate and ammonium, but did decrease the concentration of some micronutrients. This study provides basic guidance for greenhouse operators to use hydrated lime for phosphate removal from greenhouse wastewater.

Polybutadiene latex particle size distribution analysis utilizing a disk centrifuge

NARCIS (Netherlands)

Verdurmen, E.M.F.J.; Albers, J.G.; German, A.L.

1994-01-01

Polybutadiene (I) latexes prepd. by emulsifier-free emulsion polymn. and having particle diam. 50-300 nm for both unimodal and bimodal particles size distributions were analyzed by the line-start (LIST) method in a Brookhaven disk centrifuge photosedimentometer. A special spin fluid was designed to

Effects of the summer holiday season on UV filter and illicit drug concentrations in the Korean wastewater system and aquatic environment.

Science.gov (United States)

Kim, Ki Yong; Ekpeghere, Kalu Ibe; Jeong, Hee-Jin; Oh, Jeong-Eun

2017-08-01

Seasonal variations in the concentrations of eight ultraviolet (UV) filters and 22 illicit drugs including their metabolites in the Korean aquatic environment were investigated. Seawater samples from three beaches, water samples from two rivers, and influents and effluents from three wastewater treatment plants were analyzed. The UV filter concentrations in the seawater, river water, and effluent samples were 39.4-296, 35.4-117, and 6.84-51.1 ng L -1 , respectively. The total UV filter concentrations in the seawater samples were 1.9-4.4 times higher at the peak of the holiday season than outside the peak holiday season. An environmental risk assessment showed that ethylhexyl methoxy cinnamate (EHMC) could cause adverse effects on aquatic organisms in the seawater at the three beaches during the holiday period. Seven of the 22 target illicit drugs including their metabolites were detected in the wastewater influent samples, and the total illicit drug concentrations in the influent samples were 0.08-65.4 ng L -1 . The estimated daily consumption rates for cis-tramadol (Cis-TRM), methamphetamine (MTP), meperidine (MEP), and codeine (COD) were 25.7-118.4, 13.8-36.1, 1.36-12.6, and 1.75-8.64 mg d -1 (1000 people) -1 , respectively. In popular vacation area, the illicit drug consumption rates (Cis-TRM, MTP and MEP) were 1.6-2.6 times higher at the peak of the summer holiday season than at the beginning of the summer. Copyright © 2017 Elsevier Ltd. All rights reserved.

Insights on the Phytochemical Profile (Cyclopeptides and Biological Activities of Calotropis procera Latex Organic Fractions

Directory of Open Access Journals (Sweden)

Thiago Lustosa Jucá

2013-01-01

Full Text Available Calotropis procera is a medicinal plant whose pharmacological properties are associated with its latex. Here, the Calotropis procera latex fractions were investigated in an attempt to trace its phytochemical profile and measure its anti-inflammatory and toxicity activity. The crude latex was partitioned, yielding five fractions (49.4% hexane, 5.2% dichloromethane, 2.0% ethyl acetate, 2.1% n-butanol, and 41.1% aqueous. Phytochemical screening and spectroscopy analysis revealed that dichloromethane is the most chemically diverse fraction. Triterpenes were detected in both the hexane and dichloromethane fractions, while flavonoids were detected in the dichloromethane and ethyl acetate fractions. These fractions were cytotoxic to cancer cell lines (LD50 0.05 to 3.9 μg/mL and lethal to brine shrimp (LD50 10.9 to 65.7 μg/mL. Reduced neutrophil migration in rats was observed in carrageenan-induced peritonitis for the dichloromethane (67%, ethyl acetate (56%, and aqueous (72% fractions. A positive reaction with tolidine and ninhydrin suggested that cyclopeptides are in the ethyl acetate fraction. It is therefore concluded that Calotropis procera latex dichloromethane and ethyl acetate fractions exhibit both in vitro and in vivo activities as well as anti-inflammatory properties. Cyclopeptide detection is especially interesting because previous attempts to investigate these low-molecular cyclic amino acid sequences in C. procera have failed.

Assay of anti-HBs antibodies using a recombinant antigen and latex particle counting: comparison with five commercial tests.

Science.gov (United States)

Galanti, L M; Cornu, C; Masson, P L; Robert, A R; Becheanu, D; Lamy, M E; Cambiaso, C L

1991-05-01

An assay of anti-HBs antibodies based on agglutination of latex particles coated with recombinant HBs-antigen was compared with Abbott radioimmunoassay (Abbott-RIA), which uses a human plasma-derived antigen. The population examined consisted of 76 Abbott-RIA anti-HBs-negative prevaccinated subjects and 1044 serum samples anti-HBs found positive by Abbott-RIA, including 283 samples of subjects vaccinated either with a human plasma-derived vaccine (group A; n = 180) or with a recombinant vaccine (group B; n = 103). Correlation coefficients between the two techniques were respectively r = 0.89 for the whole population (n = 1044), r = 0.98 in group A and r = 0.74 in group B. Anti-HBs titres were higher with latex than with RIA in group B as shown by the regression slopes: latex = 508 + 1.11 RIA in group A and latex = -1138 + 3.97 RIA in group B, suggesting that some vaccinated subjects from group B produced antibodies against epitopes proper to the recombinant antigen. In the prevaccinated population and in group A, the latex results were compared with those of radioimmunoassays (Abbott, Sorin) and enzyme immunoassays (Behring, Roche, Pasteur). Only the Roche-EIA detected anti-HBs in the prevaccinated subjects. The correlation between the various immunoassays was r greater than 0.96 only for values higher than 100 IU/l.

Modification of Wastewater Treatment Technology at Cottonseed Oil Plant

Directory of Open Access Journals (Sweden)

Alshabab Mary Shick

2016-01-01

Full Text Available Wastewaters from cottonseed oil producing plant in Syria were studied in laboratory experiments. Aim of the study was to suggest modification of wastewater treatment technology in order to increase its efficiency. Concentration of pollutants in wastewaters was controlled by measurement of COD. According to the results of experiments it was suggested to decrease significantly (8-20 times dosages of reagents (acidifier, coagulant, flocculant in several actual stages of treatment (acidification, separation, coagulation and sedimentation and add stage of dispersed air flotation before coagulation treatment. The modified wastewater treatment technology would reduce COD to the values allowed for irrigation waters by Syrian National Standard.

Clonal stability of latex yield in eleven clones of Hevea brasiliensis Muell. Arg.

Directory of Open Access Journals (Sweden)

K.O. Omokhafe

2003-01-01

Full Text Available Eleven Hevea brasiliensis clones were evaluated for clonal stability of latex yield. A randomized complete block design was used with four replicates, two locations, seven years and three periods per year. Stability analysis was based on clone x year and clone x year x location interactions. Five stability parameters viz environmental variance, shukla's stability variance, regression of clonal latex yield on environmental index, variance due to regression and variance due to deviation from regression were applied. There was significant clone x environment effect at the two levels of interaction. Among the eleven clones, C 162 was outstanding for clonal stability and it can serve as donor parent for stability alleles. Three clones (C 76, C 150 and C 154 were also stable. The four stable clones (C 76, C 150, C 154 and C 162 are suitable for broad-spectrum recommendation for latex yield. Five clones (C 83, C 143, C 163, C 202 and RRIM 600 will require environment-specific recommendation because of their unstable phenotype. The stability feature of two clones (C 145 and C 159 was not clear and this will be investigated in subsequent studies.

Safety Evaluation Test on Human for Radiation Pre vulcanised Natural Rubber Latex (RVNRL)

International Nuclear Information System (INIS)

Pairu Ibrahim; Wan Manshol Wan Zain; Chai, Chee Keong; Sofian Ibrahim; Saadiah Sulaiman; Sharifah Ismail

2010-01-01

This paper discussed about clinical test conducted to determine safety evaluations on human for latex examination gloves and latex films made from Radiation Vulcanized Natural Rubber Latex (RVNRL). Two types of test were being adopted which are i) Modified Draize-95 test and ii) Patch Test on Sensitized Individuals. Modified Draize-95 test was conducted on 200 non-sensitized human subjects and Patch Test on Sensitized Individuals was conducted on 25 individuals who are allergic to the defined major chemical sensitizer presents in natural rubber product. It was found that Modified Draize-95 test has prove that there is no clinical evidence on the presence of residual chemical additives at the level that may induce Type IV allergy in the un sensitized general user population in the RVNRL gloves. Meanwhile Patch Test on Sensitized Individuals has proved that the patch test conducted using the test article on 25 individuals who are allergic to the defined major chemical sensitizers present in natural rubber products, thiuram, carbamates or thiazoles produced a negative response, meeting the pre requirement for the claim of reduced reaction-inducing potential. (author)

High-rate fermentative hydrogen production from beverage wastewater

International Nuclear Information System (INIS)

Sivagurunathan, Periyasamy; Sen, Biswarup; Lin, Chiu-Yue

2015-01-01

Highlights: • Hybrid immobilized-bacterial cells show stable operation over 175 days. • Low HRT of 1.5 h shows peak hydrogen production rate of 55 L/L-d. • Electricity generation is 9024 kW-d from 55 L/L-d hydrogen using beverage wastewater. • Granular sludge formed only at 2–3 h HRT with presence of Selenomonas sp. - Abstract: Hydrogen production from beverage industry wastewater (20 g/L hexose equivalent ) using an immobilized cell reactor with a continuous mode of operation was studied at various hydraulic retention times (HRT, 8–1.5 h). Maximum hydrogen production rate (HPR) of 55 L/L-d was obtained at HRT 1.5 h (an organic loading of 320 g/L-d hexose equivalent ). This HPR value is much higher than those of other industrial wastewaters employed in fermentative hydrogen production. The cell biomass concentration peaked at 3 h HRT with a volatile suspended solids (VSS) concentration of 6.31 g/L (with presence of self-flocculating Selenomonas sp.), but it dropped to 3.54 gVSS/L at 1.5 h HRT. With the shortening of HRT, lactate concentration increased but the concentration of the dominant metabolite butyrate did not vary significantly. The Clostridium species dynamics was not significantly affected, but total microbial community structure changed with respect to HRT variation as evident from PCR–DGGE analyses. Analysis of energy production rate suggests that beverage wastewater is a high energy yielding feedstock, and can replace 24% of electricity consumption in a model beverage industry

Reuse of wastewater from pulp industry for the optimization of fungal xylanase production

Directory of Open Access Journals (Sweden)

Geisiany Maria de Queiroz-Fernandes

2017-05-01

Full Text Available The production of enzymes using agro-industrial waste is a low cost alternative for the reuse of byproducts, with the subsequent impact decrease on the environment. Current analysis produced xylanase using fungus Aspergillus niger, with two types of wastewater generated during the pulp chemical bleaching phase as inducers. Xylanase was produced by submerged liquid fermentation and factorial design optimized parameters that influence production (concentration of wastewater and production period. Initial culture conditions (pH, temperature and agitation were optimized independently. Alkaline wastewater was more effective than acidic wastewater for the induction of xylanase in optimized conditions: 50% of culture medium, 7-day production, 30°C, pH 6.0 and agitation at 160 rpm. Despite different results, acidic and alkaline wastewaters induced xylanase production by A. niger when employed in concentrations lower than or equal to 50% of culture medium and in the most optimal conditions described above. Alkaline wastewater is highlighted as the most efficient for such production.

Trial Production of Surgical Gloves from Irradiated Natural Rubber Latex on Factory Scale

Directory of Open Access Journals (Sweden)

M. Utama

2005-07-01

Full Text Available Trial production of surgical gloves from irradiated natural rubber latex at the PT. Laxindo Utama Serang Banten glove factory has been carried out. The variation of heating temperature and leaching time during processing were evaluated. The physical and mechanical properties and the protein allergen respond of surgical gloves using ELISA method were measured. The results showed that the physical and mechanical of surgical gloves such as tensile strength, modulus, and elongation at break arefound to meet the requirements of the ISO or SNI standard for surgical gloves. While the allergic response through clinical tested latex-sensitive protein allergen known as ELISA test is found to be negative.

Latex allergy: assessment of knowledge, appropriate use of gloves and prevention practice among hospital healthcare workers.

Science.gov (United States)

Al-Niaimi, F; Chiang, Y Z; Chiang, Y N; Williams, J

2013-01-01

Healthcare workers and patients are often exposed to natural rubber latex (NRL) through contact with gloves and various healthcare products, which can potentially cause allergic reactions, with varying degrees of severity. In 2008, the Royal College of Physicians published their first evidence-based guidance on occupational health interventions for latex allergy, which emphasized the importance of healthcare workers having knowledge of latex allergy. This study aimed to survey the knowledge of healthcare workers (n = 156) about latex gloves and NRL allergy, routine prevention practice and the appropriate use of gloves in patient care. Healthcare workers in a large teaching hospital were surveyed using a standard questionnaire. We found that only 1% of healthcare workers were able to correctly match the appropriate gloves to the specifically designed procedure. More than half (n = 74.53%) were unable to recognize the presentation of type 1 allergy to NRL. Of the 156 participants, 131 (84%) considered that they would benefit from training about NRL allergy and the use of different types of gloves in clinical care. This survey indicates the importance of education regarding appropriate use of gloves and prevention of NRL allergy among healthcare workers, and dermatologists should play an important role in facilitating this. © The Author(s). CED © 2012 British Association of Dermatologists.

Effect of copolymer latexes on physicomechanical properties of mortar containing high volume fly ash as a replacement material of cement.

Science.gov (United States)

Negim, El-Sayed; Kozhamzharova, Latipa; Gulzhakhan, Yeligbayeva; Khatib, Jamal; Bekbayeva, Lyazzat; Williams, Craig

2014-01-01

This paper investigates the physicomechanical properties of mortar containing high volume of fly ash (FA) as partial replacement of cement in presence of copolymer latexes. Portland cement (PC) was partially replaced with 0, 10, 20, 30 50, and 60% FA. Copolymer latexes were used based on 2-hydroxyethyl acrylate (2-HEA) and 2-hydroxymethylacrylate (2-HEMA). Testing included workability, setting time, absorption, chemically combined water content, compressive strength, and scanning electron microscopy (SEM). The addition of FA to mortar as replacement of PC affected the physicomechanical properties of mortar. As the content of FA in the concrete increased, the setting times (initial and final) were elongated. The results obtained at 28 days of curing indicate that the maximum properties of mortar occur at around 30% FA. Beyond 30% FA the properties of mortar reduce and at 60% FA the properties of mortar are lower than those of the reference mortar without FA. However, the addition of polymer latexes into mortar containing FA improved most of the physicomechanical properties of mortar at all curing times. Compressive strength, combined water, and workability of mortar containing FA premixed with latexes are higher than those of mortar containing FA without latexes.

Phycoremediation of Heavy Metals in Wet Market Wastewater

Science.gov (United States)

Apandi, Najeeha; Saphira Radin Mohamed, Radin Maya; Al-Gheethi, Adel; Latiffi, Atikah; Nor Hidayah Arifin, Siti; Gani, Paran

2018-04-01

The efficiency of phycoremediation using microalgae for removing nutrients and heavy metals from wastewaters has been proved. However, the differences in the composition of wastewaters as well as microalgae species play an important role in the efficient of this process. Therefore, the present study aimed to investigate the effectiveness of Scenedesmus sp. to removal of heavy metals from wet market wastewater. Scenedesmus sp. was inoculated with 106 cells/mL into each wet market wastewater concentration included 10, 25, 50, 75 and 100% and incubated for 18 days. The highest growth rate was recorded in 50% WM with a maximum dry weight of 2006 mg L-1 which subsequently removed 93.06% of Cd, 91.5% of Cr, 92.47% of Fe, 92.40% of Zn. These findings reflected the high potential of Scenedesmus sp. in the treatment of wet market wastewater and production microalgae biomass.

Diagnosis of Trichomonous vaginalis by microscopy, latex agglutination, diamond's media, and PCR in symptomatic women, Khartoum, Sudan.

Science.gov (United States)

Saleh, Amir M; Abdalla, Hamid S; Satti, Abdelsalam B; Babiker, Suad M; Gasim, Gasim I; Adam, Ishag

2014-03-06

Trichomoniasis is the most common sexually transmitted disease. However, limited data are available on an effective technique for the diagnosis of Trichomonas vaginalis. A cross-sectional study was conducted to evaluate the accuracy of wet mount microscopy, latex agglutination, Diamond's media, and polymerase chain reaction (PCR) for detection of T. vaginalis among symptomatic women who attended the gynecological clinic at Khartoum, Sudan. Of the 297 women studied, 252 (84.8%) were positive for T. vaginalis by wet mount microscopy, 257 (86.5%) by latex agglutination, 253 (85.2%) by Diamond's media, and 253 (85.2%) by PCR. The sensitivity and specificity of wet mount microscopy were 99.2% and 97.7%, respectively, compared with PCR. The sensitivity and specificity of latex agglutination and Diamond's media were 99.6% and 88.6%, and 100.0% and 86.4%, respectively, compared with PCR. In this study, wet mount microscopy, latex agglutination, and Diamond's media were found to be highly sensitive and specific. However, the availability and cost effectiveness might limit the use of Diamond's media and PCR in routine practice. The virtual slide(s) for this article can be found here: http://www.diagnosticpathology.diagnomx.eu/vs/7859723851211496.

Treatment of highly concentrated tannery wastewater using electrocoagulation: Influence of the quality of aluminium used for the electrode.

Science.gov (United States)

Elabbas, S; Ouazzani, N; Mandi, L; Berrekhis, F; Perdicakis, M; Pontvianne, S; Pons, M-N; Lapicque, F; Leclerc, J-P

2016-12-05

This paper deals with the ability of electrocoagulation (EC) to remove simultaneously COD and chromium from a real chrome tanning wastewater in a batch stirred electro-coagulation cell provided with two aluminium-based electrodes (aluminium/copper/magnesium alloy and pure aluminium). Effects of operating time, current density and initial concentration of Cr(III) and COD have been investigated. The concentrations of pollutants have been successfully reduced to environmentally acceptable levels even if the concentrated effluent requires a long time of treatment of around 6h with a 400A/m(2) current density. The aluminium alloy was found to be more efficient than pure aluminium for removal of COD and chromium. Dilution of the waste has been tested for treatment: high abatement levels could be obtained with shorter time of treatment and lower current densities. Energy consumption of the electrocoagulation process was also discussed. The dilution by half of the concentrated waste leads to a higher abatement performance of both COD and chromium with the best energy efficiency. Copyright © 2016 Elsevier B.V. All rights reserved.

Effect of Irrigation with Wastewater on Certain Soil Physical and Chemical properties

Directory of Open Access Journals (Sweden)

Farzad Rohani Shahraki

2005-03-01

Full Text Available Depending on effluent characteristics, irrigation with wastewater plant effluent can be either beneficial or harmful. To investigate the effects of nine years of irrigation with North Isfahan Wastewater Treatment Plant effluent on physical and chemical properties of soil, a study was carried out using a randomized complete block design with three replications. Treatments included: 1 raw wastewater; 2 effluent from primary settling basin; 3 final plant effluent and 4 well water. To investigate soil physical and chemical properties, samples were taken from depths of 0-5 cm and 5-10 cm from each plot. The results showed that raw wastewater COD and SS were higher than the Iranian Standard limits for use in irrigation. So were BOD5 and turbidity of effluent from primary sedimentation tanks. From the results obtained, the raw wastewater may be considered to be of medium quality. However, regarding other parameters such as EC, SAR, Na and Pb, the quality of the raw wastewater was considerably higher than that of well water. All treatments showed medium infiltrability with respect to chloride concentration. The concentration of lead in well water was higher than in treated wastewater. It should be noted that lead concentration in all samples was less than the standard limits. The average soil bulk density and percentage of moisture in FC did not follow any specific trend. The results indicate that the soil irrigated with effluent over the nine years had a lower bulk density, a higher percentage of moisture, and a lower infiltration compared to adjacent soil not irrigated with wastewater. Analysis of variance for all results did not confirm any significant differences among treatments.

Design Criteria for Process Wastewater Pretreatment Facilities

Science.gov (United States)

1988-05-01

Stripping Column H13 ’Re Purpose: The purpose of this report, is to provide design criteria for pretreatment needs for ’ I. INTRODUCTION ’". discharge of...which a portion of the vessel is filled with packing. Packing materials vary from corrugated steel to bundles of fibers (Langdon et al., 1972) to beds...concentration(s) using Table 20. Wastewater treatability studies should be considered as a process-screening tool for all wastewater streams for

Enhanced biodegradation of methylhydrazine and hydrazine contaminated NASA wastewater in fixed-film bioreactor.

Science.gov (United States)

Nwankwoala, A U; Egiebor, N O; Nyavor, K

2001-01-01

The aerobic biodegradation of National Aeronautics and Space Administration (NASA) wastewater that contains mixtures of highly concentrated methylhydrazine/hydrazine, citric acid and their reaction product was studied on a laboratory-scale fixed film trickle-bed reactor. The degrading organisms, Achromobacter sp., Rhodococcus B30 and Rhodococcus J10, were immobilized on coarse sand grains used as support-media in the columns. Under continuous flow operation, Rhodococcus sp. degraded the methylhydrazine content of the wastewater from a concentration of 10 to 2.5 mg/mL within 12 days and the hydrazine from approximately 0.8 to 0.1 mg/mL in 7 days. The Achromobacter sp. was equally efficient in degrading the organics present in the wastewater, reducing the concentration of the methylhydrazine from 10 to approximately 5 mg/mL within 12 days and that of the hydrazine from approximately 0.8 to 0.2 mg/mL in 7 days. The pseudo first-order rate constants of 0.137 day(-1) and 0.232 day(-1) were obtained for the removal of methylhydrazine and hydrazine, respectively, in wastewater in the reactor column. In the batch cultures, rate constants for the degradation were 0.046 and 0.079 day(-1) for methylhydrazine and hydrazine respectively. These results demonstrate that the continuous flow bioreactor afford greater degradation efficiencies than those obtained when the wastewater was incubated with the microbes in growth-limited batch experiments. They also show that wastewater containing hydrazine is more amenable to microbial degradation than one that is predominant in methylhydrazine, in spite of the longer lag period observed for hydrazine containing wastewater. The influence of substrate concentration and recycle rate on the degradation efficiency is reported. The major advantages of the trickle-bed reactor over the batch system include very high substrate volumetric rate of turnover, higher rates of degradation and tolerance of the 100% concentrated NASA wastewater. The

Study of Growth Process and Phenol Biodegradation by a Bacterium Isolated from Wastewater (in vitro

Directory of Open Access Journals (Sweden)

Somayye Eskandary

2011-07-01

Full Text Available Phenol is a carbonic compound that is dangerous for humans at a concentration of 0.5 ppm in the environment. The best phenol removal from coal tar wastewaters is achieved by bioremediation. In this study, we isolated indigenous bacteria from phenolic wastewater and adapted it to a high concentration of phenol for its removal from wastewater. We also investigated the growth and removal curves of the bacteria in media with 2000 and 4000 ppm of phenol. It was observed that after lag phases of 24 and 48 hours, they grew and removed all of the phenol concentration over 264 and 312 hours. It was also found that this isolate was able to remove 2233 ppm of phenol in natural wastewater over a period of 120 hours. Identification tests showed that it is a gram-negative bactetium possibly belonging to the pseudomonas species. Phenol concentrations in wastewater can be reduced over a shorter period of time by using either this isolate alone or a group of them.

Kinetic studies on purification capability of channel flow type wastewater treatment plant

Energy Technology Data Exchange (ETDEWEB)

Hashimoto, S [Fukui Institute of Technology, Fukui (Japan); Furukawa, K; Kim, J [Osaka Univ., Osaka (Japan). Faculty of Engineering

1990-10-01

In order to develop a wastewater treatment process of secondary effluent and a wastewater treatment process of a farm village, some experiments have been carried out using bench scale and full scale hydroponic type wastewater treatment plant. This wastewater treatment system mainly consists of water channels and hydroponic water tanks. The authors carried out of a kinetic study for purification capability of the water channels while assuring the growth of microorganism in the treatment scheme. It was shown experimentally that the channel flow type wastewater treatment plant had a high TOC removal capability regardless of the kind of contact material and treatment time. Activated sludge microorganism concentration in water channels was obtained by kinetic estimation from the measured effluent suspended solid concentration. Estimated amount of activated sludge in water channels comprised only 11.5-37.4 percent of the measured amounts of withdrawn sludge, indicating high photosynthesis production of algae in water channels. 8 refs., 4 figs., 5 tabs.

Radio-vulcanization of natural rubber in the latex phase. Study of an experimental 1 tonne per hour production; Radio-vulcanisation du caoutchouc naturel en phase latex. Etude d'une production experimentale de 1 tonne par heure

Energy Technology Data Exchange (ETDEWEB)

Leveque, P; Puig, J R; Roudeix, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-07-01

After briefly reviewing the main research carried out on the radio-vulcanization of latex and elastomers, a description is given of 4 types of cell which have been used successively with a view to industrial irradiation. They have made it possible to acquire the information necessary for resolving the main problem arising during irradiation - the formation of coagulum. The first two cell are designed for irradiation by a horizontal beam ('Dynamitron'), the two others use a vertical beam ('Circe'). The study of the properties of the rubber obtained shows it to compare favorably with 'Revultex'. In the appendix are given some characteristics of natural latex and information about its processing. (authors) [French] Apres un rappel des principales etudes sur la radio-vulcanisation du latex et des elastomeres, on decrit les quatre types de cellules successivement essayes en vue de l'irradiation industrielle. Ils ont permis d'acquerir les informations necessaires a la resolution du probleme principal pose par l'irradiation, la formation de coagulum au cours de celle,-ci. Les deux premiers sont concus pour l'irradiation par un faisceau horizontal ('Dynamitron'), les derniers par un faisceau vertical ('Circe'). L'etude des proprietes du caoutchouc obtenu montre qu'il se compare favorablement au 'Revultex'. Un apercu est donne en annexe des caracteristiques du latex naturel et de sa mise en oeuvre. (auteurs)

Synthesis and characterization of novel fluoroalkyl-terminated hyperbranched polyurethane latex

Science.gov (United States)

Xu, Wei; Zhao, Weijia; Hao, Lifen; Wang, Sha; Pei, Mengmeng; Wang, Xuechuan

2018-04-01

Waterborne polyurethane (PU) emulsions are widely used in various fields and the demand for them is ever-increasing over the years. However, the hydrophilic chain extender inevitably bonded into the PU backbone can affect the water tolerance of PU. Thus, it is of great importance to improve PU water resistance effectively. Herein, novel fluoroalkyl-terminated hyperbranched polyurethane (HBPUF) latex was accordingly synthesized by graft reaction of perfluorohexyl ethyl alcohol and hyperbranched polyurethane (HBPU), which was previously obtained from interaction between hydroxyl-terminated hyperbranched polymer and PU prepolymer manufactured via the acetone process, as well as using neutralization, adding water, and high-speed stirring operations. We characterized the resultants and investigated its surface properties by IR, NMR, TEM, XRD, TGA, DSC, FE-SEM, AFM, XPS, and contact angle measurements, etc. IR and NMR tests confirmed that the fluorinated fragments had been grafted onto the tail end of HBPU. TEM, XRD, DSC, and FE-SEM results all accounted for the fact that there were multi-crystals in PU, HBPU and HBPUF. TGA results showed that thermal stabilities of the PU, HBPU, and HBPUF latex films were enhanced in turn. XPS and AFM analyses demonstrated that the fluorine-containing segments from the HBPUF terminals were prone to migrate and enrich on the film-air surface of the HBPUF latex film, which made water contact angle and water absorption of the HBPUF film be as 113.9° and 11.1%, respectively, compared to those of the PU film (77.8° and 136.2%). This research indicates that water resistance of the PU film can be efficiently enhanced by fluorinated polyurethane with novel fluoroalkyl-terminated hyperbranched structure.

Sediment diffusion method improves wastewater nitrogen removal in the receiving lake sediments.

Science.gov (United States)

Aalto, Sanni L; Saarenheimo, Jatta; Ropponen, Janne; Juntunen, Janne; Rissanen, Antti J; Tiirola, Marja

2018-07-01

Sediment microbes have a great potential to transform reactive N to harmless N 2 , thus decreasing wastewater nitrogen load into aquatic ecosystems. Here, we examined if spatial allocation of the wastewater discharge by a specially constructed sediment diffuser pipe system enhanced the microbial nitrate reduction processes. Full-scale experiments were set on two Finnish lake sites, Keuruu and Petäjävesi, and effects on the nitrate removal processes were studied using the stable isotope pairing technique. All nitrate reduction rates followed nitrate concentrations, being highest at the wastewater-influenced sampling points. Complete denitrification with N 2 as an end-product was the main nitrate reduction process, indicating that the high nitrate and organic matter concentrations of wastewater did not promote nitrous oxide (N 2 O) production (truncated denitrification) or ammonification (dissimilatory nitrate reduction to ammonium; DNRA). Using 3D simulation, we demonstrated that the sediment diffusion method enhanced the contact time and amount of wastewater near the sediment surface especially in spring and in autumn, altering organic matter concentration and oxygen levels, and increasing the denitrification capacity of the sediment. We estimated that natural denitrification potentially removed 3-10% of discharged wastewater nitrate in the 33 ha study area of Keuruu, and the sediment diffusion method increased this areal denitrification capacity on average 45%. Overall, our results indicate that sediment diffusion method can supplement wastewater treatment plant (WWTP) nitrate removal without enhancing alternative harmful processes. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

Inhibitory effects of ZnO nanoparticles on aerobic wastewater biofilms from oxygen concentration profiles determined by microelectrodes

International Nuclear Information System (INIS)

Hou, Jun; Miao, Lingzhan; Wang, Chao; Wang, Peifang; Ao, Yanhui; Qian, Jin; Dai, Shanshan

2014-01-01

Highlights: • Temporal and spatial inhibitory effects of ZnO NPs on biofilms were investigated. • 50 mg/L nano-ZnO inhibited the microbial activities only in biofilm outer layer. • Adsorbed ZnO NPs had no adverse effects on the cell membrane integrity of biofilms. • Dissolution of ZnO NPs to toxic zinc ions was the main mechanism of toxicity. - Abstract: The presence of ZnO NPs in waste streams can negatively affect the efficiency of biological nutrient removal from wastewater. However, details of the toxic effects of ZnO NPs on microbial activities of wastewater biofilms have not yet been reported. In this study, the temporal and spatial inhibitory effects of ZnO NPs on the O 2 respiration activities of aerobic wastewater biofilms were investigated using an O 2 microelectrode. The resulting time–course microelectrode measurements demonstrated that ZnO NPs inhibited O 2 respiration within 2 h. The spatial distributions of net specific O 2 respiration were determined in biofilms with and without treatment of 5 or 50 mg/L ZnO NPs. The results showed that 50 mg/L of nano-ZnO inhibited the microbial activities only in the outer layer (∼200 μm) of the biofilms, and bacteria present in the deeper parts of the biofilms became even more active. Scanning electron microscopy (SEM) analysis showed that the ZnO NPs were adsorbed onto the biofilm, but these NPs had no adverse effects on the cell membrane integrity of the biofilms. It was found that the inhibition of O 2 respiration induced by higher concentrations of ZnO NPs (50 mg/L) was mainly due to the release of zinc ions by dissolution of the ZnO NPs

Inhibitory effects of ZnO nanoparticles on aerobic wastewater biofilms from oxygen concentration profiles determined by microelectrodes

Energy Technology Data Exchange (ETDEWEB)

Hou, Jun [Key Laboratory of Integrated Regulation and Resources Development on Shallow Lakes, Ministry of Education, Hohai University, Nanjing 210098 (China); College of Environment, Hohai University, Nanjing 210098 (China); Miao, Lingzhan, E-mail: mlz1988@126.com [Key Laboratory of Integrated Regulation and Resources Development on Shallow Lakes, Ministry of Education, Hohai University, Nanjing 210098 (China); College of Environment, Hohai University, Nanjing 210098 (China); Wang, Chao, E-mail: hhuhjy973@126.com [Key Laboratory of Integrated Regulation and Resources Development on Shallow Lakes, Ministry of Education, Hohai University, Nanjing 210098 (China); College of Environment, Hohai University, Nanjing 210098 (China); Wang, Peifang; Ao, Yanhui; Qian, Jin; Dai, Shanshan [Key Laboratory of Integrated Regulation and Resources Development on Shallow Lakes, Ministry of Education, Hohai University, Nanjing 210098 (China); College of Environment, Hohai University, Nanjing 210098 (China)

2014-07-15

Highlights: • Temporal and spatial inhibitory effects of ZnO NPs on biofilms were investigated. • 50 mg/L nano-ZnO inhibited the microbial activities only in biofilm outer layer. • Adsorbed ZnO NPs had no adverse effects on the cell membrane integrity of biofilms. • Dissolution of ZnO NPs to toxic zinc ions was the main mechanism of toxicity. - Abstract: The presence of ZnO NPs in waste streams can negatively affect the efficiency of biological nutrient removal from wastewater. However, details of the toxic effects of ZnO NPs on microbial activities of wastewater biofilms have not yet been reported. In this study, the temporal and spatial inhibitory effects of ZnO NPs on the O{sub 2} respiration activities of aerobic wastewater biofilms were investigated using an O{sub 2} microelectrode. The resulting time–course microelectrode measurements demonstrated that ZnO NPs inhibited O{sub 2} respiration within 2 h. The spatial distributions of net specific O{sub 2} respiration were determined in biofilms with and without treatment of 5 or 50 mg/L ZnO NPs. The results showed that 50 mg/L of nano-ZnO inhibited the microbial activities only in the outer layer (∼200 μm) of the biofilms, and bacteria present in the deeper parts of the biofilms became even more active. Scanning electron microscopy (SEM) analysis showed that the ZnO NPs were adsorbed onto the biofilm, but these NPs had no adverse effects on the cell membrane integrity of the biofilms. It was found that the inhibition of O{sub 2} respiration induced by higher concentrations of ZnO NPs (50 mg/L) was mainly due to the release of zinc ions by dissolution of the ZnO NPs.

The fate of wastewater-derived NDMA precursors in the aquatic environment.

Science.gov (United States)

Pehlivanoglu-Mantas, Elif; Sedlak, David L

2006-03-01

To assess the stability of precursors of the chloramine disinfection byproduct N-nitrosodimethylamine (NDMA) under conditions expected in effluent-dominated surface waters, effluent samples from four municipal wastewater treatment plants were subjected to chlorination and chloramination followed by incubation in the presence of inocula derived from activated sludge. Samples subjected to free chlorine disinfection showed lower initial concentrations of NDMA precursors than those that were not chlorinated or were disinfected with pre-formed chloramines. For chloraminated and control (unchlorinated) treatments, the concentration of NDMA precursors decreased by an average of 24% over the 30-day incubation in samples from three of the four facilities. At the fourth facility, where samples were collected on three different days, NDMA precursor concentrations decreased by approximately 80% in one sample and decreased by less than 20% in the other two samples. In contrast to the low reactivity of the NDMA precursors, NDMA disappeared within 30 days under the conditions employed in these experiments. These results and measurements made in an effluent-dominated river suggest that although NDMA may be removed after wastewater effluent is discharged, wastewater-derived NDMA precursors could persist long enough to form significant concentrations of NDMA in drinking water treatment plants that use water originating from sources that are subjected to wastewater effluent discharges.

The Effect of Ozone and Zeolite Concentration to the Performance of the Treatment of Wastewater Containing Heavy Metal Using Flotation Process

Directory of Open Access Journals (Sweden)

Eva Karamah

2010-10-01

Full Text Available Industrial wastewater which contains heavy metal cannot be disposed to the environment directly, due to its toxicity. In this research, separation of metal from wastewater was conducted by sorptive flotation method, using Lampung natural zeolite as bonding agent. The most common diffuser used in the flotation process is air or oxygen. In this research, ozone is used as diffuser because it is a stronger oxidant and more dissolvable in water than oxygen. Besides, ozone is a coagulant aid and disinfectant. With ozone as diffuser, it is expected that the process become faster with higher efficiency. This research was conducted to determine ozone effectiveness as diffuser, compared with other diffuser, and also to determine optimum concentration and effectiveness of zeolite in flotation of iron, nickel and copper. The research result shows that separation of iron with air diffuser is 90.8%, air-oxygen diffuser is 95.7%, air-ozone (from air diffuser is 99.7%, and air-ozone (from oxygen diffuser is 99.7%. Natural zeolite is effective as bonding agent with optimum concentration equal to 2 gram/liter, producing separation percentage for iron equal to 99.70%, copper equal to 88.98% and Nickel equal to 98.46%.

HIGH-RATE ANAEROBIC TREATMENT OF ALCOHOLIC WASTEWATERS

Directory of Open Access Journals (Sweden)

Florencio L.

1997-01-01

Full Text Available Modern high-rate anaerobic wastewater treatment processes are rapidly becoming popular for industrial wastewater treatment. However, until recently stable process conditions could not be guaranteed for alcoholic wastewaters containing higher concentrations of methanol. Although methanol can be directly converted into methane by methanogens, under specific conditions it can also be converted into acetate and butyrate by acetogens. The accumulation of volatile fatty acids can lead to reactor instability in a weakly buffered reactor. Since this process was insufficiently understood, the application of high-rate anaerobic reactors was highly questionable. This research investigated the environmental factors that are of importance in the predominance of methylotrophic methanogens over acetogens in a natural mixed culture during anaerobic wastewater treatment in upflow anaerobic sludge bed reactors. Technological and microbiological aspects were investigated. Additionally, the route by which methanol is converted into methane is also presented

Radiation Vulcanization of Natural Rubber Latex (RVNRL): A Potential Material for Nuclear Power Plant Gloves

International Nuclear Information System (INIS)

Pairu Ibrahim; Wan Manshol Wan Zain; Keong, C.C.; Mohd Noorwadi Mat Lazim

2011-01-01

Radiation vulcanization of natural rubber latex has great potential for the production of nuclear power plant gloves due to its low ash and mineral content. And this is in-line with the role played by Malaysian Nuclear Agency as Technical Supporting Organization for Nuclear Power Program. This paper discussed the evaluation done to determine ash content in RVNRL and SVNRL films. Both samples were prepared using casting technique and the properties were compared. Films prepared from raw latex without any vulcanizing agent were regarded as a control. (author)

Effect of Copolymer Latexes on Physicomechanical Properties of Mortar Containing High Volume Fly Ash as a Replacement Material of Cement

Directory of Open Access Journals (Sweden)

El-Sayed Negim

2014-01-01

Full Text Available This paper investigates the physicomechanical properties of mortar containing high volume of fly ash (FA as partial replacement of cement in presence of copolymer latexes. Portland cement (PC was partially replaced with 0, 10, 20, 30 50, and 60% FA. Copolymer latexes were used based on 2-hydroxyethyl acrylate (2-HEA and 2-hydroxymethylacrylate (2-HEMA. Testing included workability, setting time, absorption, chemically combined water content, compressive strength, and scanning electron microscopy (SEM. The addition of FA to mortar as replacement of PC affected the physicomechanical properties of mortar. As the content of FA in the concrete increased, the setting times (initial and final were elongated. The results obtained at 28 days of curing indicate that the maximum properties of mortar occur at around 30% FA. Beyond 30% FA the properties of mortar reduce and at 60% FA the properties of mortar are lower than those of the reference mortar without FA. However, the addition of polymer latexes into mortar containing FA improved most of the physicomechanical properties of mortar at all curing times. Compressive strength, combined water, and workability of mortar containing FA premixed with latexes are higher than those of mortar containing FA without latexes.

Application of cell-based assays for toxicity characterization of complex wastewater matrices: Possible applications in wastewater recycle and reuse.

Science.gov (United States)

Shrivastava, Preeti; Naoghare, Pravin K; Gandhi, Deepa; Devi, S Saravana; Krishnamurthi, Kannan; Bafana, Amit; Kashyap, Sanjay M; Chakrabarti, Tapan

2017-08-01

Exposure to pre-concentrated inlet or outlet STP wastewater extracts at different concentrations (0.001% to 1%) induced dose-dependent toxicity in MCF-7 cells, whereas drinking water extracts did not induce cytotoxicity in cells treated. GC-MS analysis revealed the occurrence of xenobiotic compounds (Benzene, Phthalate, etc.) in inlet/outlet wastewater extracts. Cells exposed to inlet/outlet extract showed elevated levels of reactive oxygen species (ROS: inlet: 186.58%, ploss of mitochondrial membrane potential (Δψm: inlet, 74.91%, pcontrol. These concentrations induced DNA damage (Tail length: inlet: 34.4%, pcontrol (Tail length: 7.5%). Cell cycle analysis displayed drastic reduction in the G1 phase in treated cells (inlet, G1:45.0%; outlet, G1:58.3%) compared to the control (G1:67.3%). Treated cells showed 45.18% and 28.0% apoptosis compared to the control (1.2%). Drinking water extracts did not show any significant alterations with respect to ROS, Δψm, DNA damage, cell cycle and apoptosis compared to the control. Genes involved in cell cycle and apoptosis were found to be differentially expressed in cells exposed to inlet/outlet extracts. Herein, we propose cell-based toxicity assays to evaluate the efficacies of wastewater treatment and recycling processes. Copyright © 2017 Elsevier Inc. All rights reserved.

Thermochemical Wastewater Valorization via Enhanced Microbial Toxicity Tolerance

Energy Technology Data Exchange (ETDEWEB)

Beckham, Gregg T [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Thelhawadigedara, Lahiru Niroshan Jayakody [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Johnson, Christopher W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Pleitner, Brenna P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Cleveland, Nicholas S [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Michener, William E [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Olstad-Thompson, Jessica L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Vardon, Derek R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Whitham, Jason M. [Oak Ridge National Laboratory; Giannone, Richard J. [Oak Ridge National Laboratory; Klingeman, Dawn M. [Oak Ridge National Laboratory; Brown, Robert C. [Iowa State University; Brown, Steven D. [Oak Ridge National Laboratory; LanzaTech, Inc.; Hettich, Robert L. [Oak Ridge National Laboratory; Guss, Adam M. [Oak Ridge National Laboratory

2018-04-17

Thermochemical (TC) biomass conversion processes such as pyrolysis and liquefaction generate considerable amounts of wastewater, which often contains highly toxic compounds that are incredibly challenging to convert via standard wastewater treatment approaches such as anaerobic digestion. These streams represent a cost for TC biorefineries, and a potential valorization opportunity, if effective conversion methods are developed. The primary challenge hindering microbial conversion of TC wastewater is toxicity. In this study, we employ a robust bacterium, Pseudomonas putida, with TC wastewater streams to demonstrate that aldehydes are the most inhibitory compounds in these streams. Proteomics, transcriptomics, and fluorescence-based immunoassays of P. putida grown in a representative wastewater stream indicate that stress results from protein damage, which we hypothesize is a primary toxicity mechanism. Constitutive overexpression of the chaperone genes, groEL, groES, and clpB, in a genome-reduced P. putida strain improves the tolerance towards multiple TC wastewater samples up to 200-fold. Moreover, the concentration ranges of TC wastewater are industrially relevant for further bioprocess development for all wastewater streams examined here, representing different TC process configurations. Furthermore, we demonstrate proof-of-concept polyhydroxyalkanoate production from the usable carbon in an exemplary TC wastewater stream. Overall, this study demonstrates that protein quality control machinery and repair mechanisms can enable substantial gains in microbial tolerance to highly toxic substrates, including heterogeneous waste streams. When coupled to other metabolic engineering advances such as expanded substrate utilization and enhanced product accumulation, this study generally enables new strategies for biological conversion of highly-toxic, organic-rich wastewater via engineered aerobic monocultures or designer consortia.

Use of hydroponics culture to assess nutrient supply by treated wastewater.

Science.gov (United States)

Adrover, Maria; Moyà, Gabriel; Vadell, Jaume

2013-09-30

The use of treated wastewater for irrigation is increasing, especially in those areas where water resources are limited. Treated wastewaters contain nutrients that are useful for plant growth and help to reduce fertilizers needs. Nutrient content of these waters depends on the treatment system. Nutrient supply by a treated wastewater from a conventional treatment plant (CWW) and a lagooned wastewater from the campus of the University of Balearic Islands (LWW) was tested in an experiment in hydroponics conditions. Half-strength Hoagland nutrient solution (HNS) was used as a control. Barley (Hordeum vulgare L.) seedlings were grown in 4 L containers filled with the three types of water. Four weeks after planting, barley was harvested and root and shoot biomass was measured. N, P, K, Ca, Mg, Na and Fe contents were determined in both tissues and heavy metal concentrations were analysed in shoots. N, P and K concentrations were lower in LWW than in CWW, while HNS had the highest nutrient concentration. Dry weight barley production was reduced in CWW and LWW treatments to 49% and 17%, respectively, comparing to HNS. However, to a lesser extent, reduction was found in shoot and root N content. Treated wastewater increased Na content in shoots and roots of barley and Ca and Cr content in shoots. However, heavy metals content was lower than toxic levels in all the cases. Although treated wastewater is an interesting water resource, additional fertilization is needed to maintain a high productivity in barley seedlings. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effect of algal density in bead, bead size and bead concentrations ...

African Journals Online (AJOL)

Effect of algal density in bead, bead size and bead concentrations on wastewater nutrient removal. ... African Journal of Biotechnology ... The bioreactor containing algal beads (4 mm diameter) with 1.5 x 106 cells bead-1 (cell stocking) at concentration of 10.66 beads ml-1 wastewater (1:3 bead: wastewater, v/v) achieved ...

Thermal-kinetic study of natural rubber latex films vulcanized by using gamma radiation; Estudo termo-cinetico de filmes de latex de borracha natural de Hevea brasiliensis vulcanizada por radiacao gama

Energy Technology Data Exchange (ETDEWEB)

Leal, Ana Paula Pinho Rodrigues; Barros, Glaucione Gomes de [Brasilia Univ., DF (Brazil). Inst. de Quimica; Guedes, Selma M.L. [Instituto de Pesquisa em Energia Nuclear, Sao Paulo, SP (Brazil)

1999-07-01

Vulcanization of natural rubber latex by ionization radiation produces the crosslink in disperse latex particles. Advantages over conventional process of vulcanization are: the absence of carcinogenic nitrosamines, low cytotoxicity and better degradation at room conditions, due to mainly to the absence of sulfur, zinc oxide and dithiocarbamates. Thermogravimetric analysis (TG) is the measurement of the weight change of a material as a function of temperature and time. TG data different heat speed provide an alternative model of the kinetics of degradation of polymeric materials. The kinetic studies of this material showed a single degradation process at least for 76,5% of mass loss. The activation energy was 49 Kcal/mol. For higher mass loss (85%) the degradation was characterized by associate mechanism. (author)

Two-year survey of specific hospital wastewater treatment and its impact on pharmaceutical discharges.

Science.gov (United States)

Wiest, Laure; Chonova, Teofana; Bergé, Alexandre; Baudot, Robert; Bessueille-Barbier, Frédérique; Ayouni-Derouiche, Linda; Vulliet, Emmanuelle

2018-04-01

It is well known that pharmaceuticals are not completely removed by conventional activated sludge wastewater treatment plants. Hospital effluents are of major concern, as they present high concentrations of pharmaceutically active compounds. Despite this, these specific effluents are usually co-treated with domestic wastewaters. Separate treatment has been recommended. However, there is a lack of information concerning the efficiency of separate hospital wastewater treatment by activated sludge, especially on the removal of pharmaceuticals. In this context, this article presents the results of a 2-year monitoring of conventional parameters, surfactants, gadolinium, and 13 pharmaceuticals on the specific study site SIPIBEL. This site allows the characterization of urban and hospital wastewaters and their separate treatment using the same process. Flow proportional sampling, solid-phase extraction, and liquid chromatography coupled with tandem mass spectrometry were used in order to obtain accurate data and limits of quantification consistent with ultra-trace detection. Thanks to these consolidated data, an in-depth characterization of urban and hospital wastewaters was realized, as well as a comparison of treatment efficiency between both effluents. Higher concentrations of organic carbon, AOX, phosphates, gadolinium, paracetamol, ketoprofen, and antibiotics were observed in hospital wastewaters compared to urban wastewaters. Globally higher removals were observed in the hospital wastewater treatment plant, and some parameters were shown to be of high importance regarding removal efficiencies: hydraulic retention time, redox conditions, and ambient temperature. Eleven pharmaceuticals were still quantified at relevant concentrations in hospital and urban wastewaters after treatment (e.g., up to 1 μg/L for sulfamethoxazole). However, as the urban flow was about 37 times higher than the hospital flow, the hospital contribution appeared relatively low compared to

Technology of Anticorrosive Protection of Steel Constructions by Coatings Based on Rapid-Hardening Bitumen-Latex Emulsion

Directory of Open Access Journals (Sweden)

Nykyforchyn, H.M.

2016-01-01

Full Text Available The recipes of rapid-hardening bitumen-latex emulsions and coatings on its base are created, in-laboratory tests of their physical, chemical and anticorrosive properties are carried out. The technology of anticorrosive protection and the installation technical documentation for making of aqueous bitumen-latex emulsion is developed, installation is mounted and a pilot lot of rapid-hardening emulsion is produced. Experimental-industrial approbation of the technology of coating formation on pipes in oil and gas industry is carried out.

Livestock wastewater treatment by zeolite ion exchange and gamma-ray irradiation

International Nuclear Information System (INIS)

Lee, Sang Ryul; Kim, Tak Hyun; Lee, Myun Joo

2008-01-01

Livestock wastewater containing high concentrations of organic matters and ammonia-nitrogen has been known as one of the recalcitrant wastewater. It is difficult to treat by conventional wastewater treatment techniques. This study was carried out to evaluate the feasibility of zeolite ion exchange and gamma-ray irradiation treatment of livestock wastewater. The removal efficiencies of SCOD Cr and NH3-N were significantly enhanced by gamma-ray irradiation after zeolite ion exchange as a pre-treatment. However, the effects of zeolite particle size on the SCOD Cr and NH 3 -N removal efficiencies were insignificant. These results indicate that the combined process of zeolite ion exchange and gamma-ray irradiation has potential for the treatment of livestock wastewater

The application of ionising radiation in industrial wastewater treatment technology

Energy Technology Data Exchange (ETDEWEB)

Kos, L. [Inst. of Knitting Technology and Techniques, Lodz (Poland); Perkowski, J. [Inst. of Applied Radiation Chemistry, Technical Univ. of Lodz, Lodz (Poland); Ledakowicz, S. [Dept. of Bioprocess Engineering, Technical Univ. of Lodz, Lodz (Poland)

2003-07-01

An attempt was made to apply radiation techniques in the treatment of industrial wastewater from a dairy, brewery and sugar factory. For degradation of pollutants present in the wastewater, the following methods were used: irradiation, irradiation combined with aeration, ozonation, and combined irradiation and ozonation. For all three types of wastewater, the best method among these listed above appeared to be the method of irradiation combined with ozonation. Most degradable was the wastewater produced in sugar factories, and the least biodegradable appeared to be dairy wastewater. Depending on the dose of ozone and radiation, a maximum 60% reduction of COD was obtained. No effect of the wastewater aeration on its degradation by radiation was found. Changes in the content of mineral compounds were observed in none of the cases. The process of biological treatment of wastewater was carried out in a low-loaded, wetted bed. Pretreatment of the wastewater had no significant effect on the improvement of the biological step operation. Some effect was observed only in the case of the wastewater coming from a sugar factory. For medium concentrated wastewater from food industry, it is not economically justified to apply the pretreatment with the use of ionising radiation. (orig.)

Isolation of natural inhibitors of papain obtained from Carica papaya latex

Directory of Open Access Journals (Sweden)

Rubens Monti

2004-09-01

Full Text Available Studies were carried out to natural papain inhibitor from papaya latex. Fresh latex from green fruits of Carica papaya was collected and immediately transported in ice bath to the lab, from which three fractions with inhibitor effect of esterase papain activity were isolated by latex dialysis, Sephadex G-25 gel filtration and ionic exchange chromatography in SP-Sephadex C-25. The isolated fractions, identified as inhibitors I and II, showed a negative reaction with ninhydrin; however, the fraction identified as P-III showed positive reaction with ninhydrin. Kinetics data showed non-competitive inhibition (inhibitor I and uncompetitive (inhibitors II and P-III.Este trabalho apresenta novos dados sobre inibidores naturais de papaína. O látex fresco de frutos verdes de Carica papaya foi coletado pela manhã em plantações da região de Araraquara, SP, Brasil e imediatamente transportado ao laboratório em banho de gelo. Três frações com efeito inibitório da atividade esterásica da papaína foram isoladas a partir do látex fresco, através de diálise, filtração em Sephadex G-25 e cromatografia em SP-Sephadex C-25. As frações isoladas identificadas como inibidores I e II, mostraram reação negativa à ninidrina; entretanto, a fração identificada como P-III mostrou reação positiva. Dados cinéticos revelaram inibição não-competitiva (inibidor I e incompetitiva (inibidores II e P-III.

Current technologies for biological treatment of textile wastewater--a review.

Science.gov (United States)

Sarayu, K; Sandhya, S

2012-06-01

The release of colored wastewater represents a serious environmental problem and public health concern. Color removal from textile wastewater has become a big challenge over the last decades, and up to now, there is no single and economically attractive treatment method that can effectively decolorize the wastewater. Effluents from textile manufacturing, dyeing, and finishing processes contain high concentrations of biologically difficult-to-degrade or even inert auxiliaries, chemicals like acids, waxes, fats, salts, binders, thickeners, urea, surfactants, reducing agents, etc. The various chemicals such as biocides and stain repellents used for brightening, sequestering, anticreasing, sizing, softening, and wetting of the yarn or fabric are also present in wastewater. Therefore, the textile wastewater needs environmental friendly, effective treatment process. This paper provides a critical review on the current technology available for decolorization and degradation of textile wastewater and also suggests effective and economically attractive alternatives.

Concentrations of prioritized pharmaceuticals in effluents from 50 large wastewater treatment plants in the US and implications for risk estimation.

Science.gov (United States)

Kostich, Mitchell S; Batt, Angela L; Lazorchak, James M

2014-01-01

We measured concentrations of 56 active pharmaceutical ingredients (APIs) in effluent samples from 50 large wastewater treatment plants across the US. Hydrochlorothiazide was found in every sample. Metoprolol, atenolol, and carbamazepine were found in over 90% of the samples. Valsartan had the highest concentration (5300 ng/L), and also had the highest average concentration (1600 ng/L) across all 50 samples. Estimates of potential risks to healthy human adults were greatest for six anti-hypertensive APIs (lisinopril, hydrochlorothiazide, valsartan, atenolol, enalaprilat, and metoprolol), but nevertheless suggest risks of exposure to individual APIs as well as their mixtures are generally very low. Estimates of potential risks to aquatic life were also low for most APIs, but suggest more detailed study of potential ecological impacts from four analytes (sertraline, propranolol, desmethylsertraline, and valsartan). Published by Elsevier Ltd.

Potential of quixaba (Sideroxylon obtusifolium latex as a milk-clotting agent

Directory of Open Access Journals (Sweden)

Anna Carolina da Silva

2013-09-01

Full Text Available There are several obstacles to the use of chymosin in cheese production. Consequently, plant proteases have been studied as possible rennet substitutes, but most of these enzymes are unsuitable for the manufacture of cheese. The aim of this study was to evaluate the potential of latex from Sideroxylon obtusifolium as a source of milk-clotting proteases and to partially characterize the enzyme. The enzyme extract showed high protease and coagulant activities, with an optimal pH of 8.0 and temperature of 55 °C. The enzyme was stable in wide ranges of temperature and pH. Its activity was not affected by any metal ions tested; but was inhibited by phenylmethanesulfonyl fluoride and pepstatin. For the coagulant activity, the optimal concentration of CaCl2 was 10 µmol L- 1. Polyacrylamide gel electrophoresis showed four bands, with molecular weights between 17 and 64 kDa. These results indicate that the enzyme can be applied to the cheese industry.

Banyan latex: a facile fuel for the multifunctional properties of MgO nanoparticles prepared via auto ignited combustion route

International Nuclear Information System (INIS)

Anil Kumar, M R; Nagaswarupa, H P; Gurushantha, K; Pratapkumar, C; Prashantha, S C; Shashishekar, T R; Anantharaju, K S; Nagabhushana, H; Sharma, S C; Vidya, Y S; Daruka Prasad, B; Vivek Babu, C S; Vishnu Mahesh, K R

2015-01-01

MgO nanoparticles (MNPs) were prepared by a solution combustion route using banyan tree (BT) latex and glycine as fuels. The powder x-ray diffraction results indicate the formation of a single cubic phase and the crystallite size obtained from transmission electron microscopy was found to be ∼10–15 nm. Scanning electron microscopy result reveals spherical-shaped particles obtained with BT latex. However, in a chemical route, porous and agglomerated particles were obtained. The energy band gap of MNPs obtained using BT latex and a chemical route were found to be in the range 4.85–5.0 eV. Photoluminescence peaks observed at 473, 514, and 588 nm when excited at 433 nm, which were attributed to surface defects. The enhanced photocatalytic activities of spherical MgO were due to smaller crystallite size, higher surface defects, dye sensitization, and capability to reduce the electron–hole pair recombination. Further, green-synthesized MNPs exhibit superior antifungal activity against various plant pathogens. The present studies demonstrated a green engineering route for the synthesis of multifunctional MNPs using BT latex. (paper)

Potential exposure and treatment efficiency of nanoparticles in water supplies based on wastewater reclamation

DEFF Research Database (Denmark)

Kirkegaard, Peter; Hansen, Steffen Foss; Rygaard, Martin

2015-01-01

Water scarcity brings an increased focus on wastewater reclamation for drinking water supply. Meanwhile, the production volume of nanoparticles (NPs) is rapidly increasing, but to date there has been little attention given to the fate of NPs in water systems based on wastewater reclamation. We have...... investigated the possible concentrations of silver (Ag), titanium dioxide (TiO2), and zinc oxide (ZnO) nanoparticles in tap water for water supplies based on reclaimed wastewater. Tap water concentrations of the NPs were assessed by mass flow analyses of two typical wastewater reclamation concepts: 1) advanced...... studies are available on the removal efficiencies of NPs by advanced water treatment processes with a majority of the identified studies focusing on removal efficiencies in wastewater treatment plants and fate in surface waters. The NP removal efficiency of several treatment processes is unknown...

Evaluation of polar organic micropollutants as indicators for wastewater-related coastal water quality impairment

International Nuclear Information System (INIS)

Nödler, Karsten; Tsakiri, Maria; Aloupi, Maria; Gatidou, Georgia; Stasinakis, Athanasios S.; Licha, Tobias

2016-01-01

Results from coastal water pollution monitoring (Lesvos Island, Greece) are presented. In total, 53 samples were analyzed for 58 polar organic micropollutants such as selected herbicides, biocides, corrosion inhibitors, stimulants, artificial sweeteners, and pharmaceuticals. Main focus is the application of a proposed wastewater indicator quartet (acesulfame, caffeine, valsartan, and valsartan acid) to detect point sources and contamination hot-spots with untreated and treated wastewater. The derived conclusions are compared with the state of knowledge regarding local land use and infrastructure. The artificial sweetener acesulfame and the stimulant caffeine were used as indicators for treated and untreated wastewater, respectively. In case of a contamination with untreated wastewater the concentration ratio of the antihypertensive valsartan and its transformation product valsartan acid was used to further refine the estimation of the residence time of the contamination. The median/maximum concentrations of acesulfame and caffeine were 5.3/178 ng L"−"1 and 6.1/522 ng L"−"1, respectively. Their detection frequency was 100%. Highest concentrations were detected within the urban area of the capital of the island (Mytilene). The indicator quartet in the gulfs of Gera and Kalloni (two semi-enclosed embayments on the island) demonstrated different concentration patterns. A comparatively higher proportion of untreated wastewater was detected in the gulf of Gera, which is in agreement with data on the wastewater infrastructure. The indicator quality of the micropollutants to detect wastewater was compared with electrical conductivity (EC) data. Due to their anthropogenic nature and low detection limits, the micropollutants are superior to EC regarding both sensitivity and selectivity. The concentrations of atrazine, diuron, and isoproturon did not exceed the annual average of their environmental quality standards (EQS) defined by the European Commission. At two

Sulfonated macro-RAFT agents for the surfactant-free synthesis of cerium oxide-based hybrid latexes.

Science.gov (United States)

Garnier, Jérôme; Warnant, Jérôme; Lacroix-Desmazes, Patrick; Dufils, Pierre-Emmanuel; Vinas, Jérôme; van Herk, Alex

2013-10-01

Three types of amphiphatic macro-RAFT agents were employed as compatibilizers to promote the polymerization reaction at the surface of nanoceria for the synthesis of CeO2-based hybrid latexes. Macro-RAFT copolymers and terpolymers were first synthesized employing various combinations of butyl acrylate as a hydrophobic monomer and acrylic acid (AA) and/or 2-acrylamido-2-methylpropane sulfonic acid (AMPS) as hydrophilic monomers. After characterizing the adsorption of these macro-RAFT agents at the cerium oxide surface by UV-visible spectrometry, emulsion copolymerization reactions of styrene and methyl acrylate were then carried out in the presence of the surface-modified nanoceria. Dynamic Light Scattering and cryo-Transmission Electron Microscopy were employed to confirm the hybrid structure of the final CeO2/polymer latexes, and proved that the presence of acrylic acid units in amphiphatic macro-RAFT agents enabled an efficient formation of hybrid structures, while the presence of AMPS units, when combined with AA units, resulted in a better distribution of cerium oxide nanoclusters between latex particles. Copyright © 2013 Elsevier Inc. All rights reserved.

Mechanism of n-butyl acrylate sensitization action in radiation vulcanization of natural rubber latex

International Nuclear Information System (INIS)

Sabharwal, S.; Chaudhari, C.V.; Bhardwaj, Y.K.; Majali, A.B.; Das, T.N.

1996-01-01

In order to understand the role of n-butyl acrylate (nBA) in radiation vulcanization of natural rubber latex, pulse radiolysis technique has been utilized to study the reactions of the transient species produced by reaction of OH . , e- aq and H . atoms with nBA in aqueous solutions. The results show that transients produced by reaction of e- aq with nBA alone are capable of propagating the polymerization reaction and enhance the vulcanization process. These results have been further confirmed by studying the effect of electron scavengers on the vulcanization behaviour of natural rubber latex in presence of nBA. (author). 3 refs., 3 figs

Electrochemical oxidation of ammonia-containing wastewater using Ti/RuO2-Pt electrode

Directory of Open Access Journals (Sweden)

Wei-wu Hu

2009-12-01

Full Text Available The electrochemical oxidation degradation processes for artificial and actual wastewater containing ammonia were carried out with a Ti/RuO2-Pt anode and a Ti plate cathode. We studied the effects of different current densities, space sizes between the two electrodes, and amounts of added NaCl on ammonia-containing wastewater treatment. It was shown that, after a 30-min treatment under the optimal conditions, which were a current density of 20 mA/cm2, a space size between the two electrodes of 1 cm, and an added amount of 0.5 g/L of NaCl, the COD concentration in municipal wastewater was 40 mg/L, a removal rate of 90%; and the NH3-N concentration was 7 mg/L, a removal rate of 88.3%. The effluent of municipal wastewater qualified for Class A of the Discharge Standard of Pollutants for Municipal Wastewater Treatment Plant (GB18918-2002.

Potassium Permanganate as an Alternative for Gold Mining Wastewater Treatment

Science.gov (United States)

Ordiales, M.; Fernández, D.; Verdeja, L. F.; Sancho, J.

2015-09-01

The feasibility of using potassium permanganate as a reagent for cyanide oxidation in wastewater was experimentally studied. Both artificial and production wastewater from two different gold mines were tested. The experiments had three goals: determine the optimum reagent concentration and reaction time required to achieve total cyanide removal, obtain knowledge of the reaction kinetics, and improve the management of the amount of reagent. The results indicate that potassium permanganate is an effective and reliable oxidizing agent for the removal of cyanide from gold mining wastewater.

Analysis of some pharmaceuticals in municipal wastewater of Almadinah Almunawarah

KAUST Repository

Shraim, Amjad; Diab, Atef; Alsuhaimi, Awadh; Niazy, Esmail; Metwally, Mohammed; Amad, Maan H.; Sioud, Salim; Dawoud, Abdulilah

2012-01-01

The chemical pollution of water resources is a major challenge facing the humanity in this century. Pharmaceuticals and personal care products (PPCPs) are a group of emerging environmental chemical pollutants distinguished by their bioactivity and high solubility. They may also cause health complications to humans and living organisms. Pharmaceuticals enter the environment, mainly via wastewater and can eventually reach the surface and ground water. Despite this, PPCPs received less attention as environmental pollutants than other chemical pollutants (e.g. heavy metals and pesticides). The purpose of this work was to investigate the presence of some of the most frequently dispensed drugs for the residents of Almadinah Almunawarah, Saudi Arabia in the municipal wastewater before and after treatment. For this purpose, wastewater samples were collected biweekly from the city’s sewage treatment plant for a period of 4 months and analyzed the targeted drugs using tandem LC–MS. Out of the 19 investigated drugs, 5 pharmaceuticals have been found in concentrations greater than the limit of detection in both the influents and effluents of the sewage treatment plant. As expected, the concentrations of investigated pharmaceuticals in the wastewater were found to be low. These drugs and their average concentrations (in ng mL−1) in the influents were: acetaminophen (38.9), metformin (15.2), norfluoxetine (7.07), atenolol (2.04), and cephalexin (1.88). Meanwhile, the effluents contained slightly lower levels (in ng mL−1) than those of influents: acetaminophen (31.2), metformin (3.19), norfluoxetine (7.25), atenolol (0.545), and cephalexin (1.53). The results of this study supported by many other investigations indicate the inefficiency of current conventional wastewater treatment protocols in eliminating such a group of active and potentially hazardous pollutants from the wastewater.

Analysis of some pharmaceuticals in municipal wastewater of Almadinah Almunawarah

KAUST Repository

Shraim, Amjad

2012-11-29

The chemical pollution of water resources is a major challenge facing the humanity in this century. Pharmaceuticals and personal care products (PPCPs) are a group of emerging environmental chemical pollutants distinguished by their bioactivity and high solubility. They may also cause health complications to humans and living organisms. Pharmaceuticals enter the environment, mainly via wastewater and can eventually reach the surface and ground water. Despite this, PPCPs received less attention as environmental pollutants than other chemical pollutants (e.g. heavy metals and pesticides). The purpose of this work was to investigate the presence of some of the most frequently dispensed drugs for the residents of Almadinah Almunawarah, Saudi Arabia in the municipal wastewater before and after treatment. For this purpose, wastewater samples were collected biweekly from the city’s sewage treatment plant for a period of 4 months and analyzed the targeted drugs using tandem LC–MS. Out of the 19 investigated drugs, 5 pharmaceuticals have been found in concentrations greater than the limit of detection in both the influents and effluents of the sewage treatment plant. As expected, the concentrations of investigated pharmaceuticals in the wastewater were found to be low. These drugs and their average concentrations (in ng mL−1) in the influents were: acetaminophen (38.9), metformin (15.2), norfluoxetine (7.07), atenolol (2.04), and cephalexin (1.88). Meanwhile, the effluents contained slightly lower levels (in ng mL−1) than those of influents: acetaminophen (31.2), metformin (3.19), norfluoxetine (7.25), atenolol (0.545), and cephalexin (1.53). The results of this study supported by many other investigations indicate the inefficiency of current conventional wastewater treatment protocols in eliminating such a group of active and potentially hazardous pollutants from the wastewater.

Analysis of some pharmaceuticals in municipal wastewater of Almadinah Almunawarah

Directory of Open Access Journals (Sweden)

Amjad Shraim

2017-02-01

Full Text Available The chemical pollution of water resources is a major challenge facing the humanity in this century. Pharmaceuticals and personal care products (PPCPs are a group of emerging environmental chemical pollutants distinguished by their bioactivity and high solubility. They may also cause health complications to humans and living organisms. Pharmaceuticals enter the environment, mainly via wastewater and can eventually reach the surface and ground water. Despite this, PPCPs received less attention as environmental pollutants than other chemical pollutants (e.g. heavy metals and pesticides. The purpose of this work was to investigate the presence of some of the most frequently dispensed drugs for the residents of Almadinah Almunawarah, Saudi Arabia in the municipal wastewater before and after treatment. For this purpose, wastewater samples were collected biweekly from the city's sewage treatment plant for a period of 4 months and analyzed the targeted drugs using tandem LC–MS. Out of the 19 investigated drugs, 5 pharmaceuticals have been found in concentrations greater than the limit of detection in both the influents and effluents of the sewage treatment plant. As expected, the concentrations of investigated pharmaceuticals in the wastewater were found to be low. These drugs and their average concentrations (in ng mL−1 in the influents were: acetaminophen (38.9, metformin (15.2, norfluoxetine (7.07, atenolol (2.04, and cephalexin (1.88. Meanwhile, the effluents contained slightly lower levels (in ng mL−1 than those of influents: acetaminophen (31.2, metformin (3.19, norfluoxetine (7.25, atenolol (0.545, and cephalexin (1.53. The results of this study supported by many other investigations indicate the inefficiency of current conventional wastewater treatment protocols in eliminating such a group of active and potentially hazardous pollutants from the wastewater.

Properties and Characterization of Kenaf-Filled Natural Rubber Latex Foam

Directory of Open Access Journals (Sweden)

Ahmad Fikri Abdul Karim

2015-12-01

Full Text Available Kenaf powder was incorporated with natural rubber latex (NRL compound and foamed to make natural rubber latex foam (NRLF by using a well known technique called the Dunlop method. Different loadings of kenaf powder were added to NRL compound and was foamed to make NRLF. The mechanical properties, density, compression, thermal, and micro-structural characterization of control NRLF and kenaf incorporated NRLF were studied. Increasing content of kenaf reduced the tensile strength, elongation at break, and compressive strength of a NRLF. Modulus at 100% elongation and density of the NRLF increased with an increase in filler loading. Higher kenaf loading indicated higher elasticity of kenaf-filled NRLF, but the recovery percentage of kenaf-filled NRLF decreased with increasing kenaf loading. From thermogravimetric analysis (TGA result, an increase in the amount of kenaf loading from 1 to 7 phr increased the thermal stability of kenaf-filled NRLF. Morphological and micro-structural characterization performed by using scanning electron microscopy (SEM showed that kenaf powder filled up the micro-sized pores in the open cell structure of kenaf-filled NRLF.

Separation of Tritium from Wastewater

International Nuclear Information System (INIS)

JEPPSON, D.W.

2000-01-01

A proprietary tritium loading bed developed by Molecular Separations, Inc (MSI) has been shown to selectively load tritiated water as waters of hydration at near ambient temperatures. Tests conducted with a 126 (micro)C 1 tritium/liter water standard mixture showed reductions to 25 (micro)C 1 /L utilizing two, 2-meter long columns in series. Demonstration tests with Hanford Site wastewater samples indicate an approximate tritium concentration reduction from 0.3 (micro)C 1 /L to 0.07 (micro)C 1 /L for a series of two, 2-meter long stationary column beds Further reduction to less than 0.02 (micro)C 1 /L, the current drinking water maximum contaminant level (MCL), is projected with additional bed media in series. Tritium can be removed from the loaded beds with a modest temperature increase and the beds can be reused Results of initial tests are presented and a moving bed process for treating large quantities of wastewaters is proposed. The moving bed separation process appears promising to treat existing large quantities of wastewater at various US Department of Energy (DOE) sites. The enriched tritium stream can be grouted for waste disposition. The separations system has also been shown to reduce tritium concentrations in nuclear reactor cooling water to levels that allow reuse. Energy requirements to reconstitute the loading beds and waste disposal costs for this process appear modest

Lipid production from tapioca wastewater by culture of Scenedesmus sp. with simultaneous BOD, COD and nitrogen removal

Science.gov (United States)

Romaidi; Hasanudin, Muhammad; Kholifah, Khusnul; Maulidiyah, Alik; Putro, Sapto P.; Kikuchi, Akira; Sakaguchi, Toshifumi

2018-05-01

The use of microalgae to produce biodiesel or possibly remove nutrients from industrial wastewater has gained important attention during recent years due to their photosynthetic rate and its versatile nature to grow in various wastewater systems. In this study, a microalgae, Scenedesmus sp., was cultured to enhance the lipid production and nutrients removal from tapioca wastewater sample. To assess lipid production, Scenedesmus sp. was cultured in different concentration of tapioca wastewater sample (from 0 to 100 %), and nutrient removal including BOD, COD, NH4, NO2, NO3 level by Scenedesmus sp. was assessed in 100% of tapioca wastewater culture. After 8 days of culture, it was found out that 50% of tapioca wastewater sample resulted in highest concentration of lipid content than that of the other concentrations. The level of environment indicator as nutrient removal such as BOD, COD, NH4, NO2, NO3 were also decreased up to 74%, 72%, 95%, 91%, and 91%, respectively. The pH condition changed from initial condition acidic (pH: 4) to neutral or basic condition (pH: 7-8) as recommended in wastewater treatment system. This research provided a novel approach and achieved efficient simultaneous lipid production and nutrients removal from tapioca wastewater sample by Scenedesmus’s culture system.

texreg: Conversion of Statistical Model Output in R to LATEX and HTML Tables

Directory of Open Access Journals (Sweden)

Philip Leifeld

2013-11-01

Full Text Available A recurrent task in applied statistics is the (mostly manual preparation of model output for inclusion in LATEX, Microsoft Word, or HTML documents usually with more than one model presented in a single table along with several goodness-of-fit statistics. However, statistical models in R have diverse object structures and summary methods, which makes this process cumbersome. This article first develops a set of guidelines for converting statistical model output to LATEX and HTML tables, then assesses to what extent existing packages meet these requirements, and finally presents the texreg package as a solution that meets all of the criteria set out in the beginning. After providing various usage examples, a blueprint for writing custom model extensions is proposed.

Hierarchically structured self-supported latex films for flexible and semi-transparent electronics

Science.gov (United States)

Määttänen, Anni; Ihalainen, Petri; Törngren, Björn; Rosqvist, Emil; Pesonen, Markus; Peltonen, Jouko

2016-02-01

Different length scale alterations in topography, surface texture, and symmetry are known to evoke diverse cell behavior, including adhesion, orientation, motility, cytoskeletal condensation, and modulation of intracellular signaling pathways. In this work, self-supported latex films with well-defined isotropic/anisotropic surface features and hierarchical morphologies were fabricated by a peel-off process from different template surfaces. In addition, the latex films were used as substrates for evaporated ultrathin gold films with nominal thicknesses of 10 and 20 nm. Optical properties and topography of the samples were characterized using UV-vis spectroscopy and Atomic Force Microscopy (AFM) measurements, respectively. The latex films showed high-level transmittance of visible light, enabling the fabrication of semi-transparent gold electrodes. Electrochemical impedance spectroscopy (EIS) measurements were carried out for a number of days to investigate the long-term stability of the electrodes. The effect of 1-octadecanethiol (ODT) and HS(CH2)11OH (MuOH) thiolation and protein (human serum albumin, HSA) adsorption on the impedance and capacitance was studied. In addition, cyclic voltammetry (CV) measurements were carried out to determine active medicinal components, i.e., caffeic acid with interesting biological activities and poorly water-soluble anti-inflammatory drug, piroxicam. The results show that the fabrication procedure presented in this study enables the formation of platforms with hierarchical morphologies for multimodal (optical and electrical) real-time monitoring of length-scale-dependent biomaterial-surface interactions.

An evidence-based approach to medication preparation for the surgical patient at risk for latex allergy: is it time to stop being stopper poppers?

Science.gov (United States)

Heitz, James W; Bader, Stephen O

2010-09-01