Lossy compression of TPC data and trajectory tracking efficiency for the ALICE experiment

International Nuclear Information System (INIS)

Nicolaucig, A.; Ivanov, M.; Mattavelli, M.

2003-01-01

In this paper a quasi-lossless algorithm for the on-line compression of the data generated by the Time Projection Chamber (TPC) detector of the ALICE experiment at CERN is described. The algorithm is based on a lossy source code modeling technique, i.e. it is based on a source model which is lossy if samples of the TPC signal are considered one by one; conversely, the source model is lossless or quasi-lossless if some physical quantities that are of main interest for the experiment are considered. These quantities are the area and the location of the center of mass of each TPC signal pulse, representing the pulse charge and the time localization of the pulse. So as to evaluate the consequences of the error introduced by the lossy compression process, the results of the trajectory tracking algorithms that process data off-line after the experiment are analyzed, in particular, versus their sensibility to the noise introduced by the compression. Two different versions of these off-line algorithms are described, performing cluster finding and particle tracking. The results on how these algorithms are affected by the lossy compression are reported. Entropy coding can be applied to the set of events defined by the source model to reduce the bit rate to the corresponding source entropy. Using TPC simulated data according to the expected ALICE TPC performance, the compression algorithm achieves a data reduction in the range of 34.2% down to 23.7% of the original data rate depending on the desired precision on the pulse center of mass. The number of operations per input symbol required to implement the algorithm is relatively low, so that a real-time implementation of the compression process embedded in the TPC data acquisition chain using low-cost integrated electronics is a realistic option to effectively reduce the data storing cost of ALICE experiment

Influence of compressive stress in TGO layer on impedance spectroscopy from TBC coatings

Energy Technology Data Exchange (ETDEWEB)

Kang, To; Zhang, Jianhai; Yuan, Maodan; Song, Sungjin; Kim, Hakjoon; Kim, Yongseok; Seok, Changsung [Sungkyunkwan Univ., Suwon (Korea, Republic of)

2013-02-15

Impedance spectroscopy is a non destructive evaluation (NDE) method first proposed and developed for evaluating TGO layers with compressive stress inside thermally degraded plasma sprayed thermal barrier coatings (PS TBCs). A bode plot (phase angle ({Dirac_h}) vs. frequency (f)) was used to investigate the TGO layer on electrical responses. In our experimental study, the phase angle of Bode plots is sensitive for detecting TGO layers while applying compressive stress on thermal barrier coatings. It is difficult to detect TGO layers in samples isothermally aged for 100hrs and 200hrs without compressive stress, and substantial change of phase was observed these samples with compressive stress. Also, the frequency shift of the phase angle and change of the phase angle are observed in samples isothermally aged for more than 400hrs.

Tensile and compressive failure modes of laminated composites loaded by fatigue with different mean stress

Science.gov (United States)

Rotem, Assa

1990-01-01

Laminated composite materials tend to fail differently under tensile or compressive load. Under tension, the material accumulates cracks and fiber fractures, while under compression, the material delaminates and buckles. Tensile-compressive fatigue may cause either of these failure modes depending on the specific damage occurring in the laminate. This damage depends on the stress ratio of the fatigue loading. Analysis of the fatigue behavior of the composite laminate under tension-tension, compression-compression, and tension-compression had led to the development of a fatigue envelope presentation of the failure behavior. This envelope indicates the specific failure mode for any stress ratio and number of loading cycles. The construction of the fatigue envelope is based on the applied stress-cycles to failure (S-N) curves of both tensile-tensile and compressive-compressive fatigue. Test results are presented to verify the theoretical analysis.

Intrinsic Compressive Stress in Polycrystalline Films is Localized at Edges of the Grain Boundaries

Science.gov (United States)

Vasco, Enrique; Polop, Celia

2017-12-01

The intrinsic compression that arises in polycrystalline thin films under high atomic mobility conditions has been attributed to the insertion or trapping of adatoms inside grain boundaries. This compression is a consequence of the stress field resulting from imperfections in the solid and causes the thermomechanical fatigue that is estimated to be responsible for 90% of mechanical failures in current devices. We directly measure the local distribution of residual intrinsic stress in polycrystalline thin films on nanometer scales, using a pioneering method based on atomic force microscopy. Our results demonstrate that, at odds with expectations, compression is not generated inside grain boundaries but at the edges of gaps where the boundaries intercept the surface. We describe a model wherein this compressive stress is caused by Mullins-type surface diffusion towards the boundaries, generating a kinetic surface profile different from the mechanical equilibrium profile by the Laplace-Young equation. Where the curvatures of both profiles differ, an intrinsic stress is generated in the form of Laplace pressure. The Srolovitz-type surface diffusion that results from the stress counters the Mullins-type diffusion and stabilizes the kinetic surface profile, giving rise to a steady compression regime. The proposed mechanism of competition between surface diffusions would explain the flux and time dependency of compressive stress in polycrystalline thin films.

Soil Compressibility Models for a Wide Stress Range

KAUST Repository

Chong, Song-Hun; Santamarina, Carlos

2016-01-01

Soil compressibility models with physically correct asymptotic void ratios are required to analyze situations that involve a wide stress range. Previously suggested models and other functions are adapted to satisfy asymptotic void ratios at low

Trajectories of post-traumatic stress disorder symptoms among youth exposed to both natural and technological disasters.

Science.gov (United States)

Osofsky, Joy D; Osofsky, Howard J; Weems, Carl F; King, Lucy S; Hansel, Tonya C

2015-12-01

Theorists and researchers have demonstrated multiple trajectories of symptoms following disasters (Ecology and Society, 13, 2008, 9), highlighting the importance of obtaining more knowledge about exposed youth who demonstrate resilience as well as those who suffer chronic difficulties. This paper examines trajectories of post-traumatic stress disorder (PTSD) symptoms following exposure to hurricanes and the Deepwater Horizon Oil Spill to increase understanding of resilience and chronic reactions to both natural and technological disasters. A multiwave longitudinal design was used to follow N = 4,619 youth who were evaluated for PTSD symptoms, hurricane exposure, and oil spill exposure/stress at four time points over a period of 4 years. Trajectories were identified with cluster analyses and multilevel modeling. Individual trajectories were statistically identified consistent with theory. The largest group exhibited stable-low symptoms (52%), a second group showed steep declines following initial symptoms (21%), a third group exhibited increasing symptoms (18%), and a fourth group showed stable-high symptoms (9%). Both hurricane exposure and oil spill stress predicted trajectories and overall levels of PTSD symptoms. Results identified an effect of oil spill stress and hurricane exposure on symptom levels and trajectories of exposed youth. Results provide prospective data to support theories of multiple symptom trajectories following disasters and reinforce the importance of research that utilizes a developmental perspective to consider the long-term effects of disasters in youth. Findings highlight the importance of identifying symptoms and predictors of resilience as well as factors that contribute to resilience. © 2015 Association for Child and Adolescent Mental Health.

Irreversible data compression concepts with polynomial fitting in time-order of particle trajectory for visualization of huge particle system

International Nuclear Information System (INIS)

Ohtani, H; Ito, A M; Hagita, K; Kato, T; Saitoh, T; Takeda, T

2013-01-01

We propose in this paper a data compression scheme for large-scale particle simulations, which has favorable prospects for scientific visualization of particle systems. Our data compression concepts deal with the data of particle orbits obtained by simulation directly and have the following features: (i) Through control over the compression scheme, the difference between the simulation variables and the reconstructed values for the visualization from the compressed data becomes smaller than a given constant. (ii) The particles in the simulation are regarded as independent particles and the time-series data for each particle is compressed with an independent time-step for the particle. (iii) A particle trajectory is approximated by a polynomial function based on the characteristic motion of the particle. It is reconstructed as a continuous curve through interpolation from the values of the function for intermediate values of the sample data. We name this concept ''TOKI (Time-Order Kinetic Irreversible compression)''. In this paper, we present an example of an implementation of a data-compression scheme with the above features. Several application results are shown for plasma and galaxy formation simulation data

Estimation of the iron loss in deep-sea permanent magnet motors considering seawater compressive stress.

Science.gov (United States)

Xu, Yongxiang; Wei, Yanyu; Zou, Jibin; Li, Jianjun; Qi, Wenjuan; Li, Yong

2014-01-01

Deep-sea permanent magnet motor equipped with fluid compensated pressure-tolerant system is compressed by the high pressure fluid both outside and inside. The induced stress distribution in stator core is significantly different from that in land type motor. Its effect on the magnetic properties of stator core is important for deep-sea motor designers but seldom reported. In this paper, the stress distribution in stator core, regarding the seawater compressive stress, is calculated by 2D finite element method (FEM). The effect of compressive stress on magnetic properties of electrical steel sheet, that is, permeability, BH curves, and BW curves, is also measured. Then, based on the measured magnetic properties and calculated stress distribution, the stator iron loss is estimated by stress-electromagnetics-coupling FEM. At last the estimation is verified by experiment. Both the calculated and measured results show that stator iron loss increases obviously with the seawater compressive stress.

Estimation of the Iron Loss in Deep-Sea Permanent Magnet Motors considering Seawater Compressive Stress

Directory of Open Access Journals (Sweden)

Yongxiang Xu

2014-01-01

Full Text Available Deep-sea permanent magnet motor equipped with fluid compensated pressure-tolerant system is compressed by the high pressure fluid both outside and inside. The induced stress distribution in stator core is significantly different from that in land type motor. Its effect on the magnetic properties of stator core is important for deep-sea motor designers but seldom reported. In this paper, the stress distribution in stator core, regarding the seawater compressive stress, is calculated by 2D finite element method (FEM. The effect of compressive stress on magnetic properties of electrical steel sheet, that is, permeability, BH curves, and BW curves, is also measured. Then, based on the measured magnetic properties and calculated stress distribution, the stator iron loss is estimated by stress-electromagnetics-coupling FEM. At last the estimation is verified by experiment. Both the calculated and measured results show that stator iron loss increases obviously with the seawater compressive stress.

Magneto thermal convection in a compressible couple-stress fluid

Energy Technology Data Exchange (ETDEWEB)

Singh, Mahinder [Lovely School of Science, Dept. of Mathematics, Lovely Professional Univ., Phagwara (India); Kumar, Pardeep [Dept. of Mathematics, ICDEOL, H.P. Univ., Shimla (India)

2010-03-15

The problem of thermal instability of compressible, electrically conducting couple-stress fluids in the presence of a uniform magnetic field is considered. Following the linearized stability theory and normal mode analysis, the dispersion relation is obtained. For stationary convection, the compressibility, couple-stress, and magnetic field postpone the onset of convection. Graphs have been plotted by giving numerical values of the parameters to depict the stability characteristics. The principle of exchange of stabilities is found to be satisfied. The magnetic field introduces oscillatory modes in the system that were non-existent in its absence. The case of overstability is also studied wherein a sufficient condition for the non-existence of overstability is obtained. (orig.)

Study of the stress-strain state of compressed concrete elements with composite reinforcement

Directory of Open Access Journals (Sweden)

Bondarenko Yurii

2017-01-01

Full Text Available The efficiency analysis of the application of glass composite reinforcement in compressed concrete elements as a load-carrying component has been performed. The results of experimental studies of the deformation-strength characteristics of this reinforcement on compression and compressed concrete cylinders reinforced by this reinforcement are presented. The results of tests and mechanisms of sample destruction have been analyzed. The numerical analysis of the stress-strain state has been performed for axial compression of concrete elements with glasscomposite reinforcement. The influence of the reinforcement percentage on the stressed state of a concrete compressed element with the noted reinforcement is estimated. On the basis of the obtained results, it is established that the glass-composite reinforcement has positive effect on the strength of the compressed concrete elements. That is, when calculating the load-bearing capacity of such structures, the function of composite reinforcement on compression should not be neglected.

Compressive intrinsic stress originates in the grain boundaries of dense refractory polycrystalline thin films

Energy Technology Data Exchange (ETDEWEB)

Magnfält, D., E-mail: danma@ifm.liu.se; Sarakinos, K. [Nanoscale Engineering Division, Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden); Fillon, A.; Abadias, G. [Institut P' , Département Physique et Mécanique des Matériaux, Université de Poitiers-CNRS-ENSMA, SP2MI, Téléport 2, Bd M. et P. Curie, F-86962 Chasseneuil-Futuroscope (France); Boyd, R. D.; Helmersson, U. [Plasma and Coatings Physics Division, Department of Physics, Chemistry and Biology (IFM), Linköping University, SE-581 83 Linköping (Sweden)

2016-02-07

Intrinsic stresses in vapor deposited thin films have been a topic of considerable scientific and technological interest owing to their importance for functionality and performance of thin film devices. The origin of compressive stresses typically observed during deposition of polycrystalline metal films at conditions that result in high atomic mobility has been under debate in the literature in the course of the past decades. In this study, we contribute towards resolving this debate by investigating the grain size dependence of compressive stress magnitude in dense polycrystalline Mo films grown by magnetron sputtering. Although Mo is a refractory metal and hence exhibits an intrinsically low mobility, low energy ion bombardment is used during growth to enhance atomic mobility and densify the grain boundaries. Concurrently, the lateral grain size is controlled by using appropriate seed layers on which Mo films are grown epitaxially. The combination of in situ stress monitoring with ex situ microstructural characterization reveals a strong, seemingly linear, increase of the compressive stress magnitude on the inverse grain size and thus provides evidence that compressive stress is generated in the grain boundaries of the film. These results are consistent with models suggesting that compressive stresses in metallic films deposited at high homologous temperatures are generated by atom incorporation into and densification of grain boundaries. However, the underlying mechanisms for grain boundary densification might be different from those in the present study where atomic mobility is intrinsically low.

Effect of the compressive stress on both polarization rotation and phase transitions in PMN-30%PT single crystal

Directory of Open Access Journals (Sweden)

Hui Zhang

2014-05-01

Full Text Available In this paper, we have investigated the dependence of both the electromechanical effect and the electrostriction on the compressive stress in PMN-30%PT single crystal on the basis of single domain polarization rotation model. In the model, the electroelastic energy induced by the compressive stress is taken into account. The results have demonstrated that the compressive stress can lead to a significant change in the initial polarization state in the crystal. The reason lies in the stress induced anisotropy which is the coupling between the compressive stress and the electrostrictive coefficients. Thus, the initial polarization state in single crystal is determined by the combination of both electrocrystalline anisotropy and the stress induced anisotropy. The compressive stress along the [100] axis can make the polarization in the crystal be perpendicular to the stress direction, and make it difficult to be polarized to the saturation. This model is useful for better understanding both the polarization rotation and electromechanical effect in ferroelectric crystals with the compressive stress present.

Posttraumatic stress symptom trajectories among children exposed to violence.

Science.gov (United States)

Miller-Graff, Laura E; Howell, Kathryn H

2015-02-01

Little research has examined the developmental course of posttraumatic stress symptoms (PTSS) in children. The current study aimed to identify developmental trajectories of PTSS in childhood and to examine predictors of symptom presentation in 1,178 children from the Longitudinal Studies of Child Abuse and Neglect (LONGSCAN) studies, a consortium of studies focusing on the causes and effects of child maltreatment. Most children had a history of documented reports with Child Protective Services (CPS) and all were identified as living in high-risk environments. Using group-based trajectory modeling, 3 unique developmental trajectories were identified: Resilient, Clinical-Improving (PTSS in the clinical range at baseline then declining over time), and Borderline-Stable (chronically subclinical PTSS). Children in the Clinical-Improving group were more likely than children in the Resilient group to have reports of physical abuse (RRR = 1.76), emotional abuse (RRR = 2.55), neglect (RRR = 1.57), and exposure to violence at home and in the community (RRR = 1.04). Children in the Borderline-Stable group were more likely than children in the Resilient group to have a CPS history of neglect (RRR = 2.44) and exposure to violence at home and in the community (RRR = 1.04). Many children living in high-risk environments exhibit resilience to PTSS, but exposure to witnessed violence and neglect appear to put children at chronic risk for poor adjustment. These children may require more intensive, integrated clinical services that attend to multiple adverse experiences. Copyright © 2015 International Society for Traumatic Stress Studies.

Mapping concentrations of posttraumatic stress and depression trajectories following Hurricane Ike.

Science.gov (United States)

Gruebner, Oliver; Lowe, Sarah R; Tracy, Melissa; Joshi, Spruha; Cerdá, Magdalena; Norris, Fran H; Subramanian, S V; Galea, Sandro

2016-08-25

We investigated geographic concentration in elevated risk for a range of postdisaster trajectories of chronic posttraumatic stress symptom (PTSS) and depression symptoms in a longitudinal study (N = 561) of a Hurricane Ike affected population in Galveston and Chambers counties, TX. Using an unadjusted spatial scan statistic, we detected clusters of elevated risk of PTSS trajectories, but not depression trajectories, on Galveston Island. We then tested for predictors of membership in each trajectory of PTSS and depression (e.g., demographic variables, trauma exposure, social support), not taking the geographic nature of the data into account. After adjusting for significant predictors in the spatial scan statistic, we noted that spatial clusters of PTSS persisted and additional clusters of depression trajectories emerged. This is the first study to show that longitudinal trajectories of postdisaster mental health problems may vary depending on the geographic location and the individual- and community-level factors present at these locations. Such knowledge is crucial to identifying vulnerable regions and populations within them, to provide guidance for early responders, and to mitigate mental health consequences through early detection of mental health needs in the population. As human-made disasters increase, our approach may be useful also in other regions in comparable settings worldwide.

Discrete fracture in quasi-brittle materials under compressive and tensile stress states

CSIR Research Space (South Africa)

Klerck, PA

2004-01-01

Full Text Available A method for modelling discrete fracture in geomaterials under tensile and compressive stress fields has been developed based on a Mohr-Coulomb failure surface in compression and three independent anisotropic rotating crack models in tension...

A novel method for estimating soil precompression stress from uniaxial confined compression tests

DEFF Research Database (Denmark)

Lamandé, Mathieu; Schjønning, Per; Labouriau, Rodrigo

2017-01-01

. Stress-strain curves were obtained by performing uniaxial, confined compression tests on undisturbed soil cores for three soil types at three soil water potentials. The new method performed better than the Gompertz fitting method in estimating precompression stress. The values of precompression stress...... obtained from the new method were linearly related to the maximum stress experienced by the soil samples prior to the uniaxial, confined compression test at each soil condition with a slope close to 1. Precompression stress determined with the new method was not related to soil type or dry bulk density......The concept of precompression stress is used for estimating soil strength of relevance to fieldtraffic. It represents the maximum stress experienced by the soil. The most recently developed fitting method to estimate precompression stress (Gompertz) is based on the assumption of an S-shape stress...

Compressing spatio-temporal trajectories

DEFF Research Database (Denmark)

Gudmundsson, Joachim; Katajainen, Jyrki; Merrick, Damian

2009-01-01

such that the most common spatio-temporal queries can still be answered approximately after the compression has taken place. In the process, we develop an implementation of the Douglas–Peucker path-simplification algorithm which works efficiently even in the case where the polygonal path given as input is allowed...... to self-intersect. For a polygonal path of size n, the processing time is O(nlogkn) for k=2 or k=3 depending on the type of simplification....

Mechanical Stresses Induced by Compression in Castings of the Load-carrying Grate

Directory of Open Access Journals (Sweden)

Słowik J.

2016-06-01

Full Text Available The main aim of this study was to examine the compression-induced state of stress arising in castings of the guide grates during operation in pusher-type furnaces for heat treatment. The effect of grate compression is caused by its forced movement in the furnace. The introduction of flexible segments to the grate structure changes in a significant way the stress distribution, mainly by decreasing its value, and consequently considerably extends the lifetime of the grates. The stress distribution was examined in the grates with flexible segments arranged crosswise (normal to the direction of the grate compression and lengthwise (following the direction of force. A regression equation was derived to describe the relationship between the stress level in a row of ribs in the grate and the number of flexible segments of a lengthwise orientation placed in this row. It was found that, regardless of the distribution of the flexible segments in a row, the stress values were similar in all the ribs included in this row, and in a given row of the ribs/flexible segments a similar state of stress prevailed, irrespective of the position of this row in the whole structure of the grate and of the number of the ribs/flexible segments introduced therein. Parts of the grate responsible for the stress transfer were indicated and also parts which play the role of an element bonding the structure.

Long-term trajectories of posttraumatic stress disorder in veterans: the role of social resources.

Science.gov (United States)

Karstoft, Karen-Inge; Armour, Cherie; Elklit, Ask; Solomon, Zahava

2013-12-01

To (1) identify long-term trajectories of combat-induced posttraumatic stress disorder (PTSD) symptoms over a 20-year period from 1983 to 2002 in veterans with and without combat stress reaction (CSR) and (2) identify social predictors of these trajectories. A latent growth mixture modeling analysis on PTSD symptoms was conducted to identify PTSD trajectories and predictors. PTSD was defined according to DSM-III and assessed through the PTSD Inventory. Israeli male veterans with (n = 369) and without (n = 306) CSR were queried at 1, 2, and 20 years after war about combat exposure, military unit support, family environment, and social reintegration. For both study groups, we identified 4 distinct trajectories with varying prevalence across groups: resilience (CSR = 34.4%, non-CSR = 76.5%), recovery (CSR = 36.3%, non-CSR = 10.5%), delayed onset (CSR = 8.4%, non-CSR = 6.9%), and chronicity (CSR = 20.9%, non-CSR = 6.2%). Predictors of trajectories in both groups included perception of war threat (ORs = 1.59-2.47, P values ≤ .30), and negative social reintegration (ORs = 0.24-0.51, P values ≤ .047). Social support was associated with symptomatology only in the CSR group (ORs = 0.40-0.61, P values ≤ .045), while family coherence was predictive of symptomatology in the non-CSR group (OR = 0.76, P = .015) but not in the CSR group. Findings confirmed heterogeneity of long-term sequelae of combat, revealing 4 trajectories of resilience, recovery, delay, and chronicity in veterans with and without CSR. Symptomatic trajectories were more prevalent for the CSR group, suggesting that acute functional impairment predicts pathological outcomes. Predictors of symptomatic trajectories included perceived threat and social resources at the family, network, and societal levels. © Copyright 2013 Physicians Postgraduate Press, Inc.

Postdeployment Suicidal Ideations and Trajectories of Posttraumatic Stress Disorder in Danish Soldiers

DEFF Research Database (Denmark)

Madsen, T.; Karstoft, K. I.; Bertelsen, Mette

2014-01-01

Objective: Suicidal ideation in veterans is of great concern. The objective of this study is to examine how heterogeneous posttraumatic stress disorder (PTSD) trajectories are associated with postdeployment suicidal ideation in veterans 2.5 years postdeployment to a combat zone in Afghanistan....... If PTSD trajectories are associated with postdeployment suicidal ideations, then the accumulative knowledge on what characterizes veterans falling into different PTSD trajectories may provide better opportunities for early identification of suicidal high-risk veterans. Method: In this prospective study...... of PTSD (measured by the PTSD Checklist, Civilian Version) and other mental and physical health variables, demographics, and social and combat-related factors. Suicidal ideation was measured by an item from the European Parasuicide Study Interview Schedule II. In a previous study based on soldiers from...

Foam behavior of solid glass spheres – Zn22Al2Cu composites under compression stresses

International Nuclear Information System (INIS)

Aragon-Lezama, J.A.; Garcia-Borquez, A.; Torres-Villaseñor, G.

2015-01-01

Solid glass spheres – Zn22Al2Cu composites, having different densities and microstructures, were elaborated and studied under compression. Their elaboration process involves alloy melting, spheres submersion into the liquid alloy and finally air cooling. The achieved composites with densities 2.6884, 2.7936 and 3.1219 g/cm 3 were studied in casting and thermally induced, fine-grain matrix microstructures. Test samples of the composites were compressed at a 10 −3 s −1 strain rate, and their microstructure characterized before and after compression by using optical and scanning electron microscopes. Although they exhibit different compression behavior depending on their density and microstructure, all of them show an elastic region at low strains, reach their maximum stress (σ max ) at hundreds of MPa before the stress fall or collapse up to a lowest yield point (LYP), followed by an important plastic deformation at nearly constant stress (σ p ): beyond this plateau, an extra deformation can be limitedly reached only by a significant stress increase. This behavior under compression stresses is similar to that reported for metal foams, being the composites with fine microstructure which nearest behave to metal foams under this pattern. Nevertheless, the relative values of the elastic modulus, and maximum and plateau stresses do not follow the Ashby equations by changing the relative density. Generally, the studied composites behave as foams under compression, except for their peculiar parameters values (σ max , LYP, and σ p )

Six years after the wave. Trajectories of posttraumatic stress following a natural disaster.

Science.gov (United States)

Johannesson, Kerstin Bergh; Arinell, Hans; Arnberg, Filip K

2015-12-01

The characteristics of long-term trajectories of distress after disasters are unclear, since few studies include a comparison group. This study examines trajectories of recovery among survivors in comparison to individuals with indirect exposure. Postal surveys were sent to Swedish tourists, repatriated from the 2004 Indian Ocean tsunami (n=2268), at 1, 3, and 6 years after the tsunami to assess posttraumatic stress (PTS) and poor mental health. Items were used to ascertain high and moderate disaster exposure groups and an indirect exposure comparison group. Long-term PTS trajectories were best characterized by a resilient (72.3%), a severe chronic (4.6%), a moderate chronic (11.2%) and a recovering (11.9%) trajectory. Trajectories reported higher levels of PTS than the comparison group. Exposure severity and bereavement were highly influential risk factors. These findings have implications regarding anticipation of long-term psychological adjustment after natural disasters and need for interventions after a single traumatic event with few secondary stressors. Copyright © 2015 Elsevier Ltd. All rights reserved.

Shot-peening effect on the structure, microhardness, and compressive stresses of the austenitic steel 1.4539

Directory of Open Access Journals (Sweden)

Barbara Nasiłowska

2015-06-01

Full Text Available This article presents shot-peening effect on the structure, microhardness, and compressive stresses of the austenitic steel 1.4539. The research shows strengthening of the top layer and the formation of compressive stresses in the subsurface layers of the shot-peening elements.[b]Keyword[/b]: austenitic steel 1.4539, residual stresses, Waisman-Phillips’a method

Compressive pre-stress effects on magnetostrictive behaviors of highly textured Galfenol and Alfenol thin sheets

Directory of Open Access Journals (Sweden)

Julia R. Downing

2017-05-01

Full Text Available Fe-Ga (Galfenol and Fe-Al (Alfenol are rare-earth-free magnetostrictive alloys with mechanical robustness and strong magnetoelastic coupling. Since highly textured Galfenol and Alfenol thin sheets along orientations have been developed with magnetostrictive performances of ∼270 ppm and ∼160 ppm, respectively, they have been of great interest in sensor and energy harvesting applications. In this work, we investigate stress-dependent magnetostrictive behaviors in highly textured rolled sheets of NbC-added Fe80Al20 and Fe81Ga19 alloys with a single (011 grain coverage of ∼90%. A compact fixture was designed and used to introduce a uniform compressive pre-stress to those thin sheet samples along a [100] direction. As compressive pre-stress was increased to above 100 MPa, the maximum observed magnetostriction increased 42% in parallel magnetostriction along the stress direction, λ//, in highly textured (011 Fe81Ga19 thin sheets for a compressive pre-stress of 60 MPa. The same phenomena were observed for (011 Fe80Al20 (maximum increase of 88% with a 49 MPa compressive stress. This trend is shown to be consistent with published results on the effect of pre-stress on magnetostriction in rods of single crystal and textured polycrystalline Fe-Ga alloy of similar compositions, and single crystal data gathered using our experimental set up. Interestingly, the saturating field (Hs does not vary with pre-stresses, while the saturating field in rod-shaped samples of Fe-Ga increases with an increase of pre-stress. This suggests that for a range of compressive pre-stresses, thin sheet samples have larger values of d33 transduction coefficients and susceptibility than rod-shaped samples of similar alloy compositions, and hence they should provide performance benefits when used in sensor and actuator device applications. Thus, we discuss potential reasons for the unexpected trends in Hs with pre-stress, and present preliminary results from tests conducted

The influence of pre-deployment cognitive ability on post-traumatic stress disorder symptoms and trajectories

DEFF Research Database (Denmark)

Sørensen, Holger J; Andersen, Søren B; Karstoft, Karen-Inge

2016-01-01

(based on logical, verbal, numerical and spatial reasoning) were converted to a mean of 100 and with a standard deviation of 15. Results Higher pre-deployment cognitive ability scores were associated with lower risk of PTSD symptoms as assessed by the Posttraumatic Stress Disorder Checklist......-Civilian Version (PCL-C) 2.5 years post-deployment (OR=0.97; 95% CI 0.95-1.00) after adjustment for educational length, baseline PCL-C score and perceived war-zone stress. Compared to a resilient trajectory, a non-resilient relieved-worsening trajectory (high baseline mental symptoms, being symptom free during...

Effects of tensile and compressive stresses on irradiation-induced swelling in AISI 316

International Nuclear Information System (INIS)

Lauritzen, T.; Bell, W.L.; Konze, G.M.; Rosa, J.M.; Vaidyanathan, S.; Garner, F.A.

1985-05-01

The results of two recent experiments indicate that the current perception of stress-affected swelling needs revision. It appears that compressive stresses do not delay swelling as previously modeled but actually accelerate swelling at a rate comparable to that induced by tensile stresses

Foam behavior of solid glass spheres – Zn22Al2Cu composites under compression stresses

Energy Technology Data Exchange (ETDEWEB)

Aragon-Lezama, J.A., E-mail: alja@correo.azc.uam.mx [Departamento de Materiales, Universidad Autónoma Metropolitana-A, Avenida San Pablo 180, Colonia Reynosa Tamaulipas, 02200 México, D.F., México (Mexico); Garcia-Borquez, A., E-mail: a.garciaborquez@yahoo.com.mx [Ciencia de Materiales, ESFM – Instituto Politécnico Nacional, Edif. 9, Unid. Prof. A. Lopez Mateos, Colonia Lindavista, 07738 México, D.F., México (Mexico); Torres-Villaseñor, G., E-mail: gtorres@unam.mx [Departamento de Metálicos y Cerámicos, Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México, Apdo., P 70-360, México, D.F., México (Mexico)

2015-06-25

Solid glass spheres – Zn22Al2Cu composites, having different densities and microstructures, were elaborated and studied under compression. Their elaboration process involves alloy melting, spheres submersion into the liquid alloy and finally air cooling. The achieved composites with densities 2.6884, 2.7936 and 3.1219 g/cm{sup 3} were studied in casting and thermally induced, fine-grain matrix microstructures. Test samples of the composites were compressed at a 10{sup −3} s{sup −1} strain rate, and their microstructure characterized before and after compression by using optical and scanning electron microscopes. Although they exhibit different compression behavior depending on their density and microstructure, all of them show an elastic region at low strains, reach their maximum stress (σ{sub max}) at hundreds of MPa before the stress fall or collapse up to a lowest yield point (LYP), followed by an important plastic deformation at nearly constant stress (σ{sub p}): beyond this plateau, an extra deformation can be limitedly reached only by a significant stress increase. This behavior under compression stresses is similar to that reported for metal foams, being the composites with fine microstructure which nearest behave to metal foams under this pattern. Nevertheless, the relative values of the elastic modulus, and maximum and plateau stresses do not follow the Ashby equations by changing the relative density. Generally, the studied composites behave as foams under compression, except for their peculiar parameters values (σ{sub max}, LYP, and σ{sub p})

Experimental study on ultimate strength and strain behavior of concrete under biaxial compressive stresses

International Nuclear Information System (INIS)

Onuma, Hiroshi; Aoyagi, Yukio

1976-01-01

The purpose of this investigation was to study the ultimate strength failure mode and deformation behavior of concrete under short-term biaxial compressive stresses, as an aid to design and analyze the concrete structures subjected to multiaxial compression such as prestressed or reinforced concrete vessel structures. The experimental work on biaxial compression was carried out on the specimens of three mix proportions and different ages with 10cm x 10cm x 10cm cubic shape in a room controlled at 20 0 C. The results are summarized as follows. (1) To minimize the surface friction between specimens and loading platens, the pads of teflon sheets coated with silicone grease were used. The coefficient of friction was measured and was 3 percent on the average. (2) The test data showed that the strength of the concrete subjected to biaxial compression increased as compared to uniaxial compressive strength, and that the biaxial strength increase was mainly dependent on the ratio of principal stresses, and it was hardly affected by mix proportions and ages. (3) The maximum increase of strength, which occurred at the stress ratio of approximately sigma 2 /sigma 1 = 0.6, was about 27 percent higher than the uniaxial strength of concrete. (4) The ultimate strength in case of biaxial compression could be approximated by the parabolic equation. (Kako, I.)

Peace and war: trajectories of posttraumatic stress disorder symptoms before, during, and after military deployment in Afghanistan.

Science.gov (United States)

Berntsen, Dorthe; Johannessen, Kim B; Thomsen, Yvonne D; Bertelsen, Mette; Hoyle, Rick H; Rubin, David C

2012-12-01

In the study reported here, we examined posttraumatic stress disorder (PTSD) symptoms in 746 Danish soldiers measured on five occasions before, during, and after deployment to Afghanistan. Using latent class growth analysis, we identified six trajectories of change in PTSD symptoms. Two resilient trajectories had low levels across all five times, and a new-onset trajectory started low and showed a marked increase of PTSD symptoms. Three temporary-benefit trajectories, not previously described in the literature, showed decreases in PTSD symptoms during (or immediately after) deployment, followed by increases after return from deployment. Predeployment emotional problems and predeployment traumas, especially childhood adversities, were predictors for inclusion in the nonresilient trajectories, whereas deployment-related stress was not. These findings challenge standard views of PTSD in two ways. First, they show that factors other than immediately preceding stressors are critical for PTSD development, with childhood adversities being central. Second, they demonstrate that the development of PTSD symptoms shows heterogeneity, which indicates the need for multiple measurements to understand PTSD and identify people in need of treatment.

Acculturative stress is associated with trajectory of anxiety symptoms during pregnancy in Mexican-American women.

Science.gov (United States)

Preciado, Andrea; D'Anna-Hernandez, Kimberly

2017-05-01

Over half of pregnant women report anxiety symptoms and these symptoms may be precipitated by stressful experiences. Anxiety rates may be higher in Mexican-American women who experience sociocultural stressors, such as acculturation, acculturative stress and discrimination. However, the role of such stressors on the trajectory of anxiety symptoms across pregnancy is not yet known. Mexican-American women (n=151) completed surveys across pregnancy about acculturation, acculturative stress, perceived discrimination, and state anxiety. Multilevel modeling found that acculturation (Anglo orientation, b=0.050, SE=0.379, t (137.561)=0.134, p=0.894; Mexican orientation, b=0.775, SE=0.692, t (133.424)=1.121, p=0.264) and perceived discrimination (b=-1.259, SE=0.921, t (137.489)=-1.367, p=0.174) were not associated with the trajectory of anxiety symptoms. However, acculturative stress, even while controlling for perceived stress, was associated with high levels of anxiety symptoms that were elevated early in pregnancy (b=-0.045, SE=0.022, t (135.749)=-2, p=0.047). This work highlights the unique role of acculturative stress in risk for prenatal anxiety in early pregnancy. Copyright © 2016. Published by Elsevier Ltd.

Size scale dependence of compressive instabilities in layered composites in the presence of stress gradients

DEFF Research Database (Denmark)

Poulios, Konstantinos; Niordson, Christian Frithiof

2016-01-01

The compressive strength of unidirectionally or layer-wise reinforced composite materials in direction parallel to their reinforcement is limited by micro-buckling instabilities. Although the inherent compressive strength of a given material micro-structure can easily be determined by assessing its...... compressive stress but also on spatial stress or strain gradients, rendering failure initiation size scale dependent. The present work demonstrates and investigates the aforementioned effect through numerical simulations of periodically layered structures withnotches and holes under bending and compressive...... loads, respectively. The presented results emphasize the importance of the reinforcing layer thickness on the load carrying capacity of the investigated structures, at a constant volumetric fraction of the reinforcement. The observed strengthening at higher values of the relative layer thickness...

Maternal depression and trajectories of adolescent depression: The role of stress responses in youth risk and resilience.

Science.gov (United States)

Monti, Jennifer D; Rudolph, Karen D

2017-10-01

This study examined the independent and interactive contributions of maternal depression and youth stress responses to trajectories of youth depression in adolescence. Youths (n = 165, M age = 12.43, SD = 1.18) and their maternal caregivers participated in a 4-year longitudinal study. Mothers and youths were administered diagnostic interviews assessing depression, and youths provided reports of their responses to peer stress. Consistent with an interactive model, adaptive responses to stress (high effortful engagement and low involuntary disengagement) buffered the effect of maternal depression on initial levels and trajectories of youth depression, with gender differences emerging. Consistent with a dual-risk model, maternal depression and maladaptive responses to stress (high effortful disengagement and involuntary engagement) contributed additive risks such that youths displayed the highest levels of depression when they were exposed to maternal depression and showed maladaptive stress responses. This research provides novel evidence that responses to stress contribute to individual differences in depression among offspring of depressed mothers, and suggests that responses to stress are an important target for efforts to promote resilience in at-risk youth.

Optimum injection pressure of a cavitating jet on introduction of compressive residual stress into stainless steel

International Nuclear Information System (INIS)

Soyama, Hitoshi; Nagasaka, Kazuya; Takakuwa, Osamu; Naito, Akima

2011-01-01

In order to mitigate stress corrosion cracking of components used for nuclear power plants, introduction of compressive residual stress into sub-surface of the components is an effective maintenance method. The introduction of compressive residual stress using cavitation impact generated by injecting a high speed water jet into water was proposed. Water jet peening is now applying to reduce stress corrosion cracking of shrouds in the nuclear power plants. However, accidental troubles such as dropping off the components and cutting of the pipes by the jet occurred at the maintenance. In order to peen by the jet without damage, optimum injection pressure of the jet should be revealed. In the case of 'cavitation peening', cavitation is generated by injecting the high speed water jet into water. As working pressure at the cavitation peening is the pressure at cavitation bubble collapse, the injection pressure of the jet is not main parameter. The cavitation impact is increasing with the scale of the jet, i.e., scaling effect of the cavitation. It was revealed that the large scale jet at low injection pressure can introduce compressive residual stress into stainless steel comparing with the small scale jet at high injection pressure. As expected, a water jet at high injection pressure might make damage of the components. Namely, in order to avoid damage of the components, the jet at the low injection pressure will be suit for the introduction of compressive residual stress. In the present paper, in order to make clear optimum injection pressure of the cavitating jet for the introduction of compressive residual stress without damage, the residual stress of stainless steel treated by the jet at various injection pressure was measured by using an X-ray diffraction method. The injection pressure of the jet p 1 was varied from 5 MPa to 300 MPa. The diameter of the nozzle throat of the jet d was varied from 0.35 mm to 2.0 mm. The residual stress changing with depth was

Compressive stress-electrical conductivity characteristics of multiwall carbon nanotube networks

Czech Academy of Sciences Publication Activity Database

Slobodian, P.; Říha, Pavel; Lengálová, A.; Sáha, P.

2011-01-01

Roč. 46, č. 9 (2011), s. 3186-3190 ISSN 0022-2461 R&D Projects: GA AV ČR IAA200600803 Institutional research plan: CEZ:AV0Z20600510 Keywords : carbon nanotube network * compression * electrical conductivity * stress sensor Subject RIV: BK - Fluid Dynamics Impact factor: 2.015, year: 2011

Microstructure Evolution and Flow Stress Model of a 20Mn5 Hollow Steel Ingot during Hot Compression.

Science.gov (United States)

Liu, Min; Ma, Qing-Xian; Luo, Jian-Bin

2018-03-21

20Mn5 steel is widely used in the manufacture of heavy hydro-generator shaft due to its good performance of strength, toughness and wear resistance. However, the hot deformation and recrystallization behaviors of 20Mn5 steel compressed under high temperature were not studied. In this study, the hot compression experiments under temperatures of 850-1200 °C and strain rates of 0.01/s-1/s are conducted using Gleeble thermal and mechanical simulation machine. And the flow stress curves and microstructure after hot compression are obtained. Effects of temperature and strain rate on microstructure are analyzed. Based on the classical stress-dislocation relation and the kinetics of dynamic recrystallization, a two-stage constitutive model is developed to predict the flow stress of 20Mn5 steel. Comparisons between experimental flow stress and predicted flow stress show that the predicted flow stress values are in good agreement with the experimental flow stress values, which indicates that the proposed constitutive model is reliable and can be used for numerical simulation of hot forging of 20Mn5 hollow steel ingot.

Similar post-stress metabolic trajectories in young and old flies.

Science.gov (United States)

Colinet, Hervé; Renault, David

2018-02-01

Homeostenosis (i.e. decline in stress resistance and resilience with age) is a fundamental notion of the biogerontology and physiology of aging. Stressful situations typically challenge metabolic homeostasis and the capacity to recover from a stress-induced metabolic disorder might be particularly compromised in senescent individuals. In the present work, we report the effects of aging on low temperature stress tolerance and metabolic profiles in Drosophila melanogaster females of different ages. Adult flies aged 4, 16, 30 and 44days were subjected to acute and chronic cold stress, and data confirmed a strong decline in cold tolerance and resilience of old flies compared to young counterparts. Using quantitative target GC-MS analysis, we found distinct metabolic phenotypes between young (4day-old) and old (44day-old) flies, with glycolytic pathways being differentially affected between the two age groups. We also compared the robustness of metabolic homeostasis in young vs. old flies when exposed to cold stress using time-series metabolic analysis. In both age groups, we found evidence of strong alteration of metabolic profiles when flies were exposed to low temperature stress. Interestingly, the temporal metabolic trajectories during the recovery period were similar in young and old flies, despite strong differences in thermotolerance. In conclusion, metabolic signatures markedly changed with age and homeostenosis was observed in the phenotypic response to cold stress. However, these changes did not reflect in different temporal homeostatic response at metabolic level. Copyright © 2017 Elsevier Inc. All rights reserved.

Compressible Analysis of Bénard Convection of Magneto Rotatory Couple-Stress Fluid

Directory of Open Access Journals (Sweden)

Mehta C.B.

2018-02-01

Full Text Available Thermal Instability (Benard’s Convection in the presence of uniform rotation and uniform magnetic field (separately is studied. Using the linearized stability theory and normal mode analyses the dispersion relation is obtained in each case. In the case of rotatory Benard’s stationary convection compressibility and rotation postpone the onset of convection whereas the couple-stress have duel character onset of convection depending on rotation parameter. While in the absence of rotation couple-stress always postpones the onset of convection. On the other hand, magnetic field on thermal instability problem on couple-stress fluid for stationary convection couple-stress parameter and magnetic field postpones the onset of convection. The effect of compressibility also postpones the onset of convection in both cases as rotation and magnetic field. Graphs have been plotted by giving numerical values to the parameters to depict the stationary characteristics. Further, the magnetic field and rotation are found to introduce oscillatory modes which were non-existent in their absence and then the principle of exchange of stability is valid. The sufficient conditions for non-existence of overstability are also obtained.

Bulk hydrodynamic stability and turbulent saturation in compressing hot spots

Science.gov (United States)

Davidovits, Seth; Fisch, Nathaniel J.

2018-04-01

For hot spots compressed at constant velocity, we give a hydrodynamic stability criterion that describes the expected energy behavior of non-radial hydrodynamic motion for different classes of trajectories (in ρR — T space). For a given compression velocity, this criterion depends on ρR, T, and d T /d (ρR ) (the trajectory slope) and applies point-wise so that the expected behavior can be determined instantaneously along the trajectory. Among the classes of trajectories are those where the hydromotion is guaranteed to decrease and those where the hydromotion is bounded by a saturated value. We calculate this saturated value and find the compression velocities for which hydromotion may be a substantial fraction of hot-spot energy at burn time. The Lindl (Phys. Plasmas 2, 3933 (1995)] "attractor" trajectory is shown to experience non-radial hydrodynamic energy that grows towards this saturated state. Comparing the saturation value with the available detailed 3D simulation results, we find that the fluctuating velocities in these simulations reach substantial fractions of the saturated value.

High Temperature Uniaxial Compression and Stress-Relaxation Behavior of India-Specific RAFM Steel

Science.gov (United States)

Shah, Naimish S.; Sunil, Saurav; Sarkar, Apu

2018-05-01

India-specific reduced activity ferritic martensitic steel (INRAFM), a modified 9Cr-1Mo grade, has been developed by India as its own structural material for fabrication of the Indian Test Blanket Module (TBM) to be installed in the International Thermonuclear Energy Reactor (ITER). The extensive study on mechanical and physical properties of this material has been currently going on for appraisal of this material before being put to use in the ITER. High temperature compression, stress-relaxation, and strain-rate change behavior of the INRAFM steel have been investigated. The optical microscopic and scanning electron microscopic characterizations were carried out to observe the microstructural changes that occur during uniaxial compressive deformation test. Comparable true plastic stress values at 300 °C and 500 °C and a high drop in true plastic stress at 600 °C were observed during the compression test. Stress-relaxation behaviors were investigated at 500 °C, 550 °C, and 600 °C at a strain rate of 10-3 s-1. The creep properties of the steel at different temperatures were predicted from the stress-relaxation test. The Norton's stress exponent (n) was found to decrease with the increasing temperature. Using Bird-Mukherjee-Dorn relationship, the temperature-compensated normalized strain rate vs stress was plotted. The stress exponent (n) value of 10.05 was obtained from the normalized plot. The increasing nature of the strain rate sensitivity (m) with the test temperature was found from strain-rate change test. The low plastic stability with m 0.06 was observed at 600 °C. The activation volume (V *) values were obtained in the range of 100 to 300 b3. By comparing the experimental values with the literature, the rate-controlling mechanisms at the thermally activated region of high temperature were found to be the nonconservative movement of jogged screw dislocations and thermal breaking of attractive junctions.

Prenatal exposure to disaster-related traumatic stress and developmental trajectories of temperament in early childhood: Superstorm Sandy pregnancy study.

Science.gov (United States)

Zhang, Wei; Rajendran, Khushmand; Ham, Jacob; Finik, Jackie; Buthmann, Jessica; Davey, Kei; Pehme, Patricia M; Dana, Kathryn; Pritchett, Alexandra; Laws, Holly; Nomura, Yoko

2018-07-01

Little is known about the impact of prenatal maternal stress (PNMS) on the developmental trajectory of temperament and few studies have been able to incorporate a natural disaster as a quasi-experimental stressor. The current study investigated PNMS related to Superstorm Sandy ('Sandy'), a hurricane that struck the New York metropolitan area in October 2012, in terms of objective exposure during pregnancy, subjective stress reaction as assessed by maternal symptoms of post-traumatic stress, and their impact on the developmental changes in temperament during early childhood. A subsample of 318 mother-child dyads was drawn from the Stress in Pregnancy Study. Temperament was measured at 6, 12, 18, and 24 months of age. Objective exposure was associated with greater High-Intensity Pleasure, Approach, Perceptual Sensitivity and Fearfulness, but lower Cuddliness and Duration of Orientation at 6 months. Objective exposure and its interaction with subjective stress reaction predicted developmental changes in temperament. In particular, objective exposure was linked to greater increases in Activity Level but decreases in High-Intensity Pleasure, Approach, and Fearfulness. The combination of objective exposure and subjective stress reaction was also associated with greater increases in Activity Level. Temperament was measured solely via maternal report. Trimester-specific effects of Sandy on temperament were not examined. This is the first study to examine the effects of prenatal maternal exposure to a natural disaster on trajectories of early childhood temperament. Findings suggest that both objective stress exposure and subjective stress reaction in-utero predict developmental trajectories of temperament in early childhood. Copyright © 2018 Elsevier B.V. All rights reserved.

Density and permeability of a loess soil: long-term organic matter effect and the response to compressive stress

DEFF Research Database (Denmark)

Arthur, Emmanuel; Schjønning, Per; Møldrup, Per

2013-01-01

to compressive stress, undisturbed soil cores were collected from a long-term fertilisation experiment in Bad Lauchstädt in Germany, including combinations of animal manure and mineral fertilisers. The cores were drained to -100 hPa matric potential and exposed to uniaxial confined compression (200k......Pa). Investigated indicators for compression resistance included compression index, precompression stress, and resistance and resilience indices based on measured soil physical properties (bulk density, air-filled porosity, air permeability, and void ratio). Soil resilience was assessed following exposure...... but the correlation was not significant. However, initial bulk density (ρbi) and initial gravimetric water content (wi) were significantly positively correlated to the indices of soil compression resistance, with the effect of ρbi being significantly stronger. Significant recovery of airfilled porosity and air...

Analytic examination of mechanism for compressive residual stress introduction with low plastic strain using peening

International Nuclear Information System (INIS)

Ishibashi, Ryo; Hato, Hisamitsu; Miyazaki, Katsumasa; Yoshikubo, Fujio

2016-01-01

Our goal for this study was to understand the cause of the differences in surface properties between surfaces processed using water jet peening (WJP) and shot peening (SP) and to examine the compressive residual stress introduction process with low plastic strain using SP. The dynamic behaviors of stress and strain in surfaces during these processes were analyzed through elasto-plastic calculations using a finite-element method program, and the calculated results were compared with measured results obtained through experiments. Media impacting a surface results in a difference in the hardness and microstructure of the processed surface. During SP, a shot deforms the surface locally with stress concentration in the early stages of the impact, while shock waves deform the surface evenly throughout the wave passage across the surface during WJP. A shot with a larger diameter creates a larger impact area on the surface during shot impact. Thus, SP with a large-diameter shot suppresses the stress concentration under the same kinetic energy condition. As the shot diameter increases, the equivalent plastic strain decreases. On the other hand, the shot is subject to size restriction since the calculated results indicate the compressive residual stress at the surface decreased and occasionally became almost zero as the shot diameter increased. Thus, compressive residual stress introduction with low plastic strain by using SP is considered achievable by using shots with a large diameter and choosing the appropriate peening conditions. (author)

In vitro degradation kinetics of pure PLA and Mg/PLA composite: Effects of immersion temperature and compression stress.

Science.gov (United States)

Li, Xuan; Chu, Chenglin; Wei, Yalin; Qi, Chenxi; Bai, Jing; Guo, Chao; Xue, Feng; Lin, Pinghua; Chu, Paul K

2017-01-15

The effects of the immersion temperature and compression stress on the in vitro degradation behavior of pure poly-lactic acid (pure-PLA) and PLA-based composite unidirectionally reinforced with micro-arc oxidized magnesium alloy wires (Mg/PLA or MAO-MAWs/PLA) are investigated. The degradation kinetics of pure-PLA and the PLA matrix in MAO-MAWs/PLA exhibit an Arrhenius-type behavior. For the composite, the synergic degradation of MAO-MAWs maintains a steady pH and mitigates the degradation of PLA matrix during immersion. However, the external compression stress decreases the activation energy (E a ) and pre-exponential factor (k 0 ) consequently increasing the degradation rate of PLA. Under a compression stress of 1MPa, E a and k 0 of pure PLA are 57.54kJ/mol and 9.74×10 7 day -1 , respectively, but 65.5kJ/mol and 9.81×10 8 day -1 for the PLA matrix in the composite. Accelerated tests are conducted in rising immersion temperature in order to shorten the experimental time. Our analysis indicates there are well-defined relationships between the bending strength of the specimens and the PLA molecular weight during immersion, which are independent of the degradation temperature and external compression stress. Finally, a numerical model is established to elucidate the relationship of bending strength, the PLA molecular weight, activation energy, immersion time and temperature. We systematically evaluate the effects of compression stress and temperature on the degradation properties of two materials: (pure-PLA) and MAO-MAWs/PLA (or Mg/PLA). The initial in vitro degradation kinetics of the unstressed or stressed pure-PLA and MAO-MAWs/PLA composite is confirmed to be Arrhenius-like. MAO-MAWs and external compression stress would influence the degradation activation energy (E a ) and pre-exponential factor (k 0 ) of PLA, and we noticed there is a linear relationship between E a and ln k 0 . Thereafter, we noticed that Mg 2+ , not H + , plays a significant role on the

Toward compression of small cell population: harnessing stress in passive regions of dielectric elastomer actuators

Science.gov (United States)

Poulin, Alexandre; Rosset, Samuel; Shea, Herbert

2014-03-01

We present a dielectric elastomer actuator (DEA) for in vitro analysis of mm2 biological samples under periodic compressive stress. Understanding how mechanical stimuli affect cell functions could lead to significant advances in diseases diagnosis and drugs development. We previously reported an array of 72 micro-DEAs on a chip to apply a periodic stretch to cells. To diversify our cell mechanotransduction toolkit we have developed an actuator for periodic compression of small cell populations. The device is based on a novel design which exploits the effects of non-equibiaxial pre-stretch and takes advantage of the stress induced in passive regions of DEAs. The device consists of two active regions separated by a 2mm x 2mm passive area. When connected to an AC high-voltage source, the two active regions periodically compress the passive region. Due to the non-equibiaxial pre-stretch it induces uniaxial compressive strain greater than 10%. Cells adsorbed on top of this passive gap would experience the same uniaxial compressive stain. The electrodes configuration confines the electric field and prevents it from reaching the biological sample. A thin layer of silicone is casted on top of the device to ensure a biocompatible environment. This design provides several advantages over alternative technologies such as high optical transparency of the area of interest (passive region under compression) and its potential for miniaturization and parallelization.

Experimental Study on Properties of Methane Diffusion of Coal Block under Triaxial Compressive Stress

Science.gov (United States)

Zhao, Hong-Bao

2014-01-01

Taking the standard size coal block samples defined by ISRM as research objects, both properties of methane diffusion of coal block under triaxial compressive stress and characteristic influences caused by methane pressure were systematically studied with thermo-fluid-solid coupling with triaxial servocontrolled seepage equipment of methane-containing coal. The result shows the methane diffusion property of coal block under triaxial compressive stress was shown in four-stage as follow, first is sharply reduce stage, second is hyperbolic reduce stage, third is close to a fixed value stage, fourth stage is 0. There is a special point making the reduced rate of characteristic curve of methane diffusion speed become sharply small; the influences of shape of methane diffusion speed characteristic curve caused by methane pressure are not obvious, which only is shown in numerical size of methane diffusion speed. Test time was extended required by appear of the special point makes the reduce rate of methane diffusion speed become sharply small. The fitting four-phase relation of methane diffusion of coal block under triaxial compressive stress was obtained, and the idea is proposed that influences of the fitting four-phase relation caused by methane pressure were only shown in value of fitting parameters. PMID:25531000

Compressed sensing along physically plausible sampling trajectories in MRI

International Nuclear Information System (INIS)

Chauffert, Nicolas

2015-01-01

Magnetic Resonance Imaging (MRI) is a non-invasive and non-ionizing imaging technique that provides images of body tissues, using the contrast sensitivity coming from the magnetic parameters (T_1, T_2 and proton density). Data are acquired in the κ-space, corresponding to spatial Fourier frequencies. Because of physical constraints, the displacement in the κ-space is subject to kinematic constraints. Indeed, magnetic field gradients and their temporal derivative are upper bounded. Hence, the scanning time increases with the image resolution. Decreasing scanning time is crucial to improve patient comfort, decrease exam costs, limit the image distortions (eg, created by the patient movement), or decrease temporal resolution in functional MRI. Reducing scanning time can be addressed by Compressed Sensing (CS) theory. The latter is a technique that guarantees the perfect recovery of an image from under sampled data in κ-space, by assuming that the image is sparse in a wavelet basis. Unfortunately, CS theory cannot be directly cast to the MRI setting. The reasons are: i) acquisition (Fourier) and representation (wavelets) bases are coherent and ii) sampling schemes obtained using CS theorems are composed of isolated measurements and cannot be realistically implemented by magnetic field gradients: the sampling is usually performed along continuous or more regular curves. However, heuristic application of CS in MRI has provided promising results. In this thesis, we aim to develop theoretical tools to apply CS to MRI and other modalities. On the one hand, we propose a variable density sampling theory to answer the first impediment. The more the sample contains information, the more it is likely to be drawn. On the other hand, we propose sampling schemes and design sampling trajectories that fulfill acquisition constraints, while traversing the κ-space with the sampling density advocated by the theory. The second point is complex and is thus addressed step by step

Modeling parenting stress trajectories among low-income young mothers across the child's second and third years: Factors accounting for stability and change.

Science.gov (United States)

Chang, Yiting; Fine, Mark A

2007-12-01

This study investigated parenting stress trajectories among low-income young mothers and the factors that are associated with change and stability of parenting stress as children aged from 14 to 36 months old. With a sample of 580 young mothers who applied to the Early Head Start Program, growth mixture modeling identified 3 trajectory classes of parenting stress: a chronically high group (7% of the sample), an increasing group (10% of the sample), and a decreasing group (83% of the sample). Maternal personal resources distinguished between the increasing and decreasing classes, whereas maternal personal resources, child characteristics, and contextual influences explained differences between the chronically high and decreasing trajectory classes. Findings suggest that for interventions to be effective, programs need to assess maternal, child, and contextual factors to better address the particular unique needs of young mothers.

Design and analysis of a toroidal tester for the measurement of core losses under axial compressive stress

Energy Technology Data Exchange (ETDEWEB)

Alatawneh, Natheer, E-mail: natheer80@yahoo.com [Department of Mining and Materials Engineering, McGill University, QC H3A 0G4 (Canada); Rahman, Tanvir; Lowther, David A. [Department of Electrical and Computer Engineering, McGill University, QC H3A 0E9 (Canada); Chromik, Richard [Department of Mining and Materials Engineering, McGill University, QC H3A 0G4 (Canada)

2017-06-15

Highlights: • Develop a toroidal tester for magnetic measurements under compressive axial stress. • The shape of the toroidal ring has been verified using 3D stress analysis. • The developed design has been prototyped, and measurements were carried out. • Physical explanations for the core loss trend due to stress are provided. - Abstract: Electric machine cores are subjected to mechanical stresses due to manufacturing processes. These stresses include radial, circumferential and axial components that may have significant influences on the magnetic properties of the electrical steel and hence, on the output and efficiencies of electrical machines. Previously, most studies of iron losses due to mechanical stress have considered only radial and circumferential components. In this work, an improved toroidal tester has been designed and developed to measure the core losses and the magnetic properties of electrical steel under a compressive axial stress. The shape of the toroidal ring has been verified using 3D stress analysis. Also, 3D electromagnetic simulations show a uniform flux density distribution in the specimen with a variation of 0.03 T and a maximum average induction level of 1.5 T. The developed design has been prototyped, and measurements were carried out using a steel sample of grade 35WW300. Measurements show that applying small mechanical stresses normal to the sample thickness rises the delivered core losses, then the losses decrease continuously as the stress increases. However, the drop in core losses at high stresses does not go lower than the free-stress condition. Physical explanations for the observed trend of core losses as a function of stress are provided based on core loss separation to the hysteresis and eddy current loss components. The experimental results show that the effect of axial compressive stress on magnetic properties of electrical steel at high level of inductions becomes less pronounced.

Numerical Analysis of Joule Heating Behavior and Residual Compressive Stress around Crack Tip under High Electric Load

Directory of Open Access Journals (Sweden)

Thomas Jin-Chee Liu

2017-01-01

Full Text Available This paper discusses the Joule heating effect and residual compressive stress near the crack tip under the electro-thermo-structural coupling state. For the crack tip field, the compressive condition is important for retarding or stopping the crack growth.

Parenting stress trajectories in mothers of very preterm infants to 2 years.

Science.gov (United States)

Gray, Peter H; Edwards, Dawn M; Gibbons, Kristen

2018-01-01

To examine levels of parenting stress in mothers of preterm and term infants when the children were 2 years old; to determine the trajectory of stress over three time periods and to examine the association of maternal and neonatal factors and developmental outcomes with parenting stress. It is a prospective longitudinal study to determine parenting stress in mothers of preterm and term infants with outcomes having been previously obtained at 4 and 12 months. At 2 years, 79 preterm mothers (96 babies) and 64 term mothers (77 babies) participated. The mothers completed the Parenting Stress Index-Short Form (PSI-SF), the Depression, Anxiety, Stress Scale (DASS) and the Child Behaviour Checklist (CBCL). The infants had a neurological examination and the Bayley-III scales were administered. The mean total PSI-SF at 2 years was significantly higher for the preterm group compared with the term group of mothers (p=0.007). There was a significant increase in the mean total PSI over time for the preterm mothers (pparenting stress and abnormal scores on the DASS (pparenting stress and maternal demographics, neonatal factors or Bayley-III results. Parenting stress in mothers of preterm infants continues to be high at 2 years having increased over time. Maternal mental health problems and infant behavioural issues contribute to the stress. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

The effect of through-thickness compressive stress on mode II interlaminar fracture toughness

NARCIS (Netherlands)

Catalanotti, G.; Furtado, C.; Scalici, T.; Pitarresi, G.; van der Meer, F.P.; Camanho, PP

2017-01-01

The effect of through-thickness compressive stress on mode II interlaminar fracture toughness is investigated experimentally and replicated numerically. The modified Transverse Crack Tensile specimen recently proposed by the authors is used, together with an experimental device designed to apply

Expanded heat treatment to form residual compressive hoop stress on inner surface of zirconium alloy tubing

International Nuclear Information System (INIS)

Megata, Masao

1997-01-01

A specific heat treatment process that introduces hoop stress has been developed. This technique can produce zirconium alloy tubing with a residual compressive hoop stress near the inner surface by taking advantage of the mechanical anisotropy in hexagonal close-packed zirconium crystal. Since a crystal having its basal pole parallel to the tangential direction of the tubing is easier to exhibit plastic elongation under the hoop stress than that having its basal pole parallel to the radial direction, the plastic and elastic elongation can coexist under a certain set of temperature and hoop stress conditions. The mechanical anisotropy plays a role to extend the coexistent stress range. Thus, residual compressive hoop stress is formed at the inner surface where more plastic elongation occurs during the heat treatment. This process is referred to as expanded heat treatment. Since this is a fundamental crystallographic principle, it has various applications. The application to improve PCI/SCC (pellet cladding interaction/stress corrosion cracking) properties of water reactor fuel cladding is promising. Excellent results were obtained with laboratory-scale heat treatment and an out-reactor iodine SCC test. These results included an extension of the time to SCC failure. (author)

Stress-dislocation interaction mechanism in low-temperature thermo-compression sintering of Ag NPs

Science.gov (United States)

Wang, Fuliang; Tang, Zikai; He, Hu

2018-04-01

The sintering of metal nanoparticles (NPs) has been widely studied in the field of nanotechnology, and low-temperature sintering has become the industry standard. In this study, a molecular dynamics (MD) model was established to study the sintering behaviour of silver NPs during low-temperature thermo-compression. Primarily, we studied the sintering process, in which the ratio of neck radius to particle radius (x/r) changes. Under a uniaxial pressure, the maximum ratio in the temperature range 420-425 K was 1. According to the change of x/r, the process can be broken down into three stages: the neck-formation stage, neck-growth stage, and neck-stability stage. In addition, the relationship between potential energy, internal stress, and dislocation density during sintering is discussed. The results showed that cycling internal stress played an important role in sintering. Under the uniaxial pressure, the stress-dislocation interaction was found to be the major mechanism for thermo-compression sintering because the plastic deformation product dislocation intensified the diffusion of atoms. Also, the displacement vector, the mean square displacement, and the changing crystal structure during sintering were studied.

Stress-dislocation interaction mechanism in low-temperature thermo-compression sintering of Ag NPs

Directory of Open Access Journals (Sweden)

Fuliang Wang

2018-04-01

Full Text Available The sintering of metal nanoparticles (NPs has been widely studied in the field of nanotechnology, and low-temperature sintering has become the industry standard. In this study, a molecular dynamics (MD model was established to study the sintering behaviour of silver NPs during low-temperature thermo-compression. Primarily, we studied the sintering process, in which the ratio of neck radius to particle radius (x/r changes. Under a uniaxial pressure, the maximum ratio in the temperature range 420–425 K was 1. According to the change of x/r, the process can be broken down into three stages: the neck-formation stage, neck-growth stage, and neck-stability stage. In addition, the relationship between potential energy, internal stress, and dislocation density during sintering is discussed. The results showed that cycling internal stress played an important role in sintering. Under the uniaxial pressure, the stress-dislocation interaction was found to be the major mechanism for thermo-compression sintering because the plastic deformation product dislocation intensified the diffusion of atoms. Also, the displacement vector, the mean square displacement, and the changing crystal structure during sintering were studied.

Reliability analysis and optimisation of subsea compression system facing operational covariate stresses

International Nuclear Information System (INIS)

Okaro, Ikenna Anthony; Tao, Longbin

2016-01-01

This paper proposes an enhanced Weibull-Corrosion Covariate model for reliability assessment of a system facing operational stresses. The newly developed model is applied to a Subsea Gas Compression System planned for offshore West Africa to predict its reliability index. System technical failure was modelled by developing a Weibull failure model incorporating a physically tested corrosion profile as stress in order to quantify the survival rate of the system under additional operational covariates including marine pH, temperature and pressure. Using Reliability Block Diagrams and enhanced Fusell-Vesely formulations, the whole system was systematically decomposed to sub-systems to analyse the criticality of each component and optimise them. Human reliability was addressed using an enhanced barrier weighting method. A rapid degradation curve is obtained on a subsea system relative to the base case subjected to a time-dependent corrosion stress factor. It reveals that subsea system components failed faster than their Mean time to failure specifications from Offshore Reliability Database as a result of cumulative marine stresses exertion. The case study demonstrated that the reliability of a subsea system can be systematically optimised by modelling the system under higher technical and organisational stresses, prioritising the critical sub-systems and making befitting provisions for redundancy and tolerances. - Highlights: • Novel Weibull Corrosion-Covariate model for reliability analysis of subsea assets. • Predict the accelerated degradation profile of a subsea gas compression. • An enhanced optimisation method based on Fusell-Vesely decomposition process. • New optimisation approach for smoothening of over- and under-designed components. • Demonstrated a significant improvement in producing more realistic failure rate.

Trajectories of posttraumatic stress symptoms (PTSS) after major war among Palestinian children: Trauma, family- and child-related predictors.

Science.gov (United States)

Punamäki, Raija-Leena; Palosaari, Esa; Diab, Marwan; Peltonen, Kirsi; Qouta, Samir R

2015-02-01

Research shows great individual variation in changes in posttraumatic stress symptoms (PTSSs) after major traumas of terrorist attacks, military combat, and natural disasters. Earlier studies have identified specific mental health trajectories both in children and adults. This study aimed, first, to identify potential PTSS-related trajectories by using latent class growth analyses among children in a three-wave assessment after the 2008/2009 War on Gaza, Palestine. Second, it analyzed how family- and child related factors (e.g., attachment relations, posttraumatic cognitions (PTCs), guilt, and emotion regulation) associate with the trajectory class membership. The sample consisted of 240 Palestinian children (49.4% girls and 50.6% boys) of 10-13 years of age (M=11.29, SD=0.68), who completed PTSS (CRIES) assessments at 3 (T1), 5 (T2), and 11 (T3) months after the war. Children reported their personal exposure to war trauma, attachment style, cognitive trauma processing, and emotion regulation, and their parents reported family war trauma exposure and attachment style. Results revealed a three-trajectory solution, a majority of children belonging to the Recovery trajectory (n=183), and a minority belonged either to Resistant trajectory (n=29) or to Increasing symptoms trajectory (n=28). Low levels of negative posttraumatic cognitive appraisals, feelings of guilt and emotion regulation were characteristic of children in the Resistant trajectory as compared to Increasing symptoms trajectory. Father׳s attachment security was further associated with the Resistant trajectory membership. Children׳s attachment avoidance and high parental trauma were typical to children in Recovery trajectory (as compared to the Increasing symptoms trajectory). Copyright © 2014 Elsevier B.V. All rights reserved.

Comparison of measured and computed radial trajectories of plasma focus devices UMDPF1 and UMDPF0

Energy Technology Data Exchange (ETDEWEB)

Lim, L. H.; Yap, S. L., E-mail: yapsl@um.edu.my; Lim, L. K.; Lee, M. C.; Poh, H. S.; Ma, J. [Plasma Technology Research Centre, Department of Physics, Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia); Yap, S. S. [UMPEDAC, University of Malaya, 50603 Kuala Lumpur (Malaysia); Faculty of Engineering, Multimedia University, Cyberjaya, 63100 Selangor (Malaysia); Lee, S. [Plasma Technology Research Centre, Department of Physics, Faculty of Science, University of Malaya, 50603 Kuala Lumpur (Malaysia); INTI International University, 71800 Nilai (Malaysia); Institute for Plasma Focus Studies, 32 Oakpark Drive, Chadstone 3148 (Australia)

2015-09-15

In published literature, there has been scant data on radial trajectory of the plasma focus and no comparison of computed with measured radial trajectory. This paper provides the first such comparative study. We compute the trajectories of the inward-moving radial shock and magnetic piston of UMDPF1 plasma focus and compare these with measured data taken from a streak photograph. The comparison shows agreement with the measured radial trajectory in terms of average speeds and general shape of trajectory. This paper also presents the measured trajectory of the radially compressing piston in another machine, the UMDPF0 plasma focus, confirming that the computed radial trajectory also shows similar general agreement. Features of divergence between the computed and measured trajectories, towards the end of the radial compression, are discussed. From the measured radial trajectories, an inference is made that the neutron yield mechanism could not be thermonuclear. A second inference is made regarding the speeds of axial post-pinch shocks, which are recently considered as a useful tool for damage testing of fusion-related wall materials.

Compression Characteristics of Solid Wastes as Backfill Materials

OpenAIRE

Meng Li; Jixiong Zhang; Rui Gao

2016-01-01

A self-made large-diameter compression steel chamber and a SANS material testing machine were chosen to perform a series of compression tests in order to fully understand the compression characteristics of differently graded filling gangue samples. The relationship between the stress-deformation modulus and stress-compression degree was analyzed comparatively. The results showed that, during compression, the deformation modulus of gangue grew linearly with stress, the overall relationship bet...

Efficient One-click Browsing of Large Trajectory Sets

DEFF Research Database (Denmark)

Krogh, Benjamin Bjerre; Andersen, Ove; Lewis-Kelham, Edwin

2014-01-01

presents a novel query type called sheaf, where users can browse trajectory data sets using a single mouse click. Sheaves are very versatile and can be used for location-based advertising, travel-time analysis, intersection analysis, and reachability analysis (isochrones). A novel in-memory trajectory...... index compresses the data by a factor of 12.4 and enables execution of sheaf queries in 40 ms. This is up to 2 orders of magnitude faster than existing work. We demonstrate the simplicity, versatility, and efficiency of sheaf queries using a real-world trajectory set consisting of 2.7 million...

p38 MAPK mediated in compressive stress-induced chondrogenesis of rat bone marrow MSCs in 3D alginate scaffolds.

Science.gov (United States)

Li, Juan; Zhao, Zhihe; Yang, Jingyuan; Liu, Jun; Wang, Jun; Li, Xiaoyu; Liu, Yurong

2009-12-01

Mesenchymal stem cells (MSCs) are well known to have the capability to form bone and cartilage, and chondrogenesis derived from MSCs is reported to be affected by mechanical stimuli. This research was aimed to study the effects of cyclic compressive stress on the chondrogenic differentiation of rat bone marrow-derived MSCs (BMSCs) which were encapsulated in alginate scaffolds and cultured with or without chondrogenic medium, and to investigate the role of p38 MAPK phospho-relay cascade in this process. The results show that the gene expression of chondrocyte-specific markers of Col2alpha1, aggrecan, Sox9, Runx2, and Ihh was upregulated by dynamic compressive stress introduced at the 8th day of chondrogenic differentiation in vitro. The p38 MAPK was activated by chondrogenic cytokines in a slow and lagged way, but activated by cyclic compressive stimulation in a rapid and transient manner. And inhibition of p38 activity with SB203580 suppressed gene expression of chondrocyte-specific genes stimulated by chondrogenic medium and (or) cyclic compressive stress. These findings suggest that p38 MAPK signal acts as an essential mediator in the mechano-biochemical transduction and subsequent transcriptional regulation in the process of chondrogenesis.

Individual trajectories in stress covary with immunity during recovery from cancer diagnosis and treatments.

Science.gov (United States)

Thornton, Lisa M; Andersen, Barbara L; Crespin, Timothy R; Carson, William E

2007-02-01

Research connects stressful events with altered immune regulation, but the role of subjective stress is uncertain. Using a longitudinal design, we provide a statistically powerful test of the relationship between subjective stress (perceived stress, emotional distress) and immunity (T cell blastogenesis, natural killer cell cytotoxicity, [NKCC]) as individuals adjust to a severe stressor, a cancer diagnosis and its treatments. Women with regional breast cancer (N=113) were assessed at diagnosis/surgery and reassessed 4, 8, 12, and 18 months later. Latent growth curve analysis tested two hypotheses: (1) initial levels of subjective stress will correlate inversely with initial levels of immunity, and (2) rate of change in subjective stress will correlate inversely with rate of change in immunity. As predicted by Hypothesis 1, participants with high initial subjective stress showed poor initial blastogenesis. As predicted by Hypothesis 2, participants exhibiting an early, rapid decline in subjective stress also showed rapid improvement in NKCC. Follow-up analyses revealed perceived stress to be strongly related to immune function, while emotional distress was not. This is the first study to investigate trajectories in stress and immunity during recovery from a major stressor. Results imply that NK and T cells are sensitive to different aspects of the stress response. While T cell blastogenesis correlated with initial (peak) subjective stress, NKCC correlated with change (improvement) in subjective stress. These data highlight the importance of subjective stress, particularly stress appraisals, in the immune response to a major stressor.

Field Measurement of Dynamic Compressive Stress Response of Pavement-Subgrade Induced by Moving Heavy-Duty Trucks

Directory of Open Access Journals (Sweden)

Lingshi An

2018-01-01

Full Text Available This paper presents the dynamic compressive stress response of pavement-subgrade induced by moving heavy-duty trucks. In order to study the distribution characteristic of dynamic pressure of pavement-subgrade in more detail, truck loadings, truck speeds, and dynamic pressure distributions at different depths were monitored under twenty-five working conditions on the section of Qiqihar-Nenjiang Highway in Heilongjiang Province, China. The effects of truck loading, truck speed, and depth on dynamic compressive stress response can be concluded as follows: (1 increasing truck loading will increase the dynamic pressure amplitude of subgrade-pavement and dominant frequencies are close to the characteristic frequencies caused by heavy-duty trucks at the speed of 70 km/h; (2 as truck speed increases, the dynamic pressure amplitudes of measuring points have an increasing tendency; the dynamic pressure spectrums are also significantly influenced by truck speed: the higher the truck speed, the wider the spectrum and the higher the dominant frequencies; (3 as depth increases, the dynamic pressure amplitudes of measuring points decrease rapidly. The influence of the front axle decreases gradually until disappearing and the compressive stress superposition phenomenon caused by rear double axles can be found with increasing depth.

Cell cytoskeletal changes effected by static compressive stress lead to changes in the contractile properties of tissue regenerative collagen membranes

Directory of Open Access Journals (Sweden)

K Gellynck

2013-06-01

Full Text Available Static compressive stress can influence the matrix, which subsequently affects cell behaviour and the cell’s ability to further transform the matrix. This study aimed to assess response to static compressive stress at different stages of osteoblast differentiation and assess the cell cytoskeleton’s role as a conduit of matrix-derived stimuli. Mouse bone marrow mesenchymal stem cells (MSCs (D1 ORL UVA, osteoblastic cells (MC3T3-E1 and post-osteoblast/pre-osteocyte-like cells (MLO-A5 were seeded in hydrated and compressed collagen gels. Contraction was quantified macroscopically, and cell morphology, survival, differentiation and mineralisation assessed using confocal microscopy, alamarBlue® assay, real-time quantitative reverse transcription polymerase chain reaction (RT-qPCR and histological stains, respectively. Confocal microscopy demonstrated cell shape changes and favourable microfilament organisation with static compressive stress of the collagen matrix; furthermore, cell survival was greater compared to the hydrated gels. The stage of osteoblast differentiation determined the degree of matrix contraction, with MSCs demonstrating the greatest amount. Introduction of microfilament disrupting inhibitors confirmed that pre-stress and tensegrity forces were under the influence of gel density, and there was increased survival and differentiation of the cells within the compressed collagen compared to the hydrated collagen. There was also relative stiffening and differentiation with time of the compressed cell-seeded collagen, allowing for greater manipulation. In conclusion, the combined collagen chemistry and increased density of the microenvironment can promote upregulation of osteogenic genes and mineralisation; MSCs can facilitate matrix contraction to form an engineered membrane with the potential to serve as a ‘pseudo-periosteum’ in the regeneration of bone defects.

Creep and creep recovery of concrete subjected to triaxial compressive stresses at elevated temperature

International Nuclear Information System (INIS)

Ohnuma, Hiroshi; Abe, Hirotoshi

1979-01-01

In order to design rationally the vessels made of prestressed concrete for nuclear power stations and to improve the accuracy of high temperature creep analysis, the Central Research Institute of Electric Power Industry had carried out the proving experiments with scale models. In order to improve the accuracy of analysis, it is important to grasp the creep behavior of the concrete subjected to triaxial compressive stresses at high temperature as the basic property of concrete, because actual prestressed concrete vessels are in such conditions. In this paper, the triaxial compression creep test at 60 deg. C using the concrete specimens with same mixing ratio as the scale models is reported. The compressive strength of the concrete at the age of 28 days was 406 kg/cm 2 , and the age of the concrete at the time of loading was 63 days. Creep and creep recovery were measured for 5 months and 2 months, respectively. The creep of concrete due to uniaxial compression increased with temperature rise, and the creep strain at 60 deg. C was 2.54 times as much as that at 20 deg. C. The effective Poisson's ratio in triaxial compression creep was 0.15 on the average, based on the creep strain due to uniaxial compression at 60 deg. C. The creep recovery rate in high temperature, triaxial compression creep was 33% on the average. (Kako, I.)

Exposure to Violence during Adolescence as a Predictor of Perceived Stress Trajectories in Emerging Adulthood.

Science.gov (United States)

Heinze, Justin E; Stoddard, Sarah A; Aiyer, Sophie M; Eisman, Andria B; Zimmerman, Marc A

2017-01-01

Early exposure to violence during adolescence is related to negative psycho-social outcomes later in life. In the present study, we examined the influence of cumulative exposure to violence during adolescence and trajectories of perceived stress in emerging adulthood in a sample of at-risk urban youth ( N = 850; 80.1% African American; 50% female). Growth curve modeling indicated an overall decrease in reported stress as individuals aged. Baseline levels of violence exposure ( M age = 14.9) were associated with higher perceived stress levels in emerging adulthood ( M age = 20.1), but also slightly more negative perceived stress slopes from adolescence into emerging adulthood ( M age = 15.9-22.1). Individuals reporting increased violence exposure over time during adolescence also reported higher perceived stress levels in emerging adulthood ( M age = 20.1). Associations held after controlling for demographics and baseline functioning variables. The results suggest that violence exposure may disrupt normative adaptation to daily stressors in emerging adulthood.

Pattern formation under residual compressive stress in free sustained aluminum films

International Nuclear Information System (INIS)

Yu Senjiang; Ye Quanlin; Zhang Yongju; Cai Pinggen; Xu Xiaojun; Chen Jiangxing; Ye Gaoxiang

2005-01-01

A nearly free sustained aluminum (Al) film system has been successfully fabricated by vapor phase deposition of Al atoms on silicone oil surfaces and an unusual type of ordered patterns at the micrometer scale has been systematically studied. The ordered patterns are composed of a large number of parallel key-shaped domains and possess a sandwiched structure. The nucleation and growth of the patterns are very susceptible to the growth period, deposition rate, nominal film thickness and location of the film. The experiment shows that the ordered patterns are induced by the residual compressive stress in the film owing to contraction of the liquid surface after deposition. The appearance of these stress relief patterns generally represents the stress distribution in the nearly free sustained Al films, which mainly results from the characteristic boundary condition and the nearly zero adhesion of the solid-liquid interface

Design and analysis of a toroidal tester for the measurement of core losses under axial compressive stress

Science.gov (United States)

Alatawneh, Natheer; Rahman, Tanvir; Lowther, David A.; Chromik, Richard

2017-06-01

Electric machine cores are subjected to mechanical stresses due to manufacturing processes. These stresses include radial, circumferential and axial components that may have significant influences on the magnetic properties of the electrical steel and hence, on the output and efficiencies of electrical machines. Previously, most studies of iron losses due to mechanical stress have considered only radial and circumferential components. In this work, an improved toroidal tester has been designed and developed to measure the core losses and the magnetic properties of electrical steel under a compressive axial stress. The shape of the toroidal ring has been verified using 3D stress analysis. Also, 3D electromagnetic simulations show a uniform flux density distribution in the specimen with a variation of 0.03 T and a maximum average induction level of 1.5 T. The developed design has been prototyped, and measurements were carried out using a steel sample of grade 35WW300. Measurements show that applying small mechanical stresses normal to the sample thickness rises the delivered core losses, then the losses decrease continuously as the stress increases. However, the drop in core losses at high stresses does not go lower than the free-stress condition. Physical explanations for the observed trend of core losses as a function of stress are provided based on core loss separation to the hysteresis and eddy current loss components. The experimental results show that the effect of axial compressive stress on magnetic properties of electrical steel at high level of inductions becomes less pronounced.

The effects of compressive stress and contamination liquids on the ultrasonic detection of fatigue cracks

International Nuclear Information System (INIS)

Wooldridge, A.B.

1980-01-01

The influence of compressive stress on the reflection and transmission of ultrasound has been investigated for fatigue cracks. An examination has been made of the shear wave corner echoes from surface breaking fatigue cracks which were grown at constant stress intensity factor to control the roughness of the faces. In this way a correlation has been established between the roughness of the surfaces and the ultrasonic response at both zero load and under stress. The effect of liquids in the cracks has also been studied and the results compared with theoretical predictions for a thin sided parallel gap. (author)

Analysis of internal stress and anelasticity in the shock-compressed state from unloading wave data

International Nuclear Information System (INIS)

Johnson, J.N.; Lomdahl, P.S.; Wills, J.M.

1991-01-01

This paper reports on time resolved shock-wave measurements have often been used to infer microstructural behavior in crystalline solids. The authors apply this approach to an interpretation of the release-wave response of an aluminum alloy (6061-T6) as it is dynamically unloaded from a shock-compressed state of 20.7 GPa. The anelastic behavior in the initial portion of the unloading wave is attributed to the accumulation of internal stresses created by the shock process. Specific internal-stress models which are investigated are the double pile-up, the single pile-up, and single dislocation loops between pinning points. It is found that the essential characteristics of double and single pile-ups can be represented by a single dislocation between two pinned dislocations of like sing. Calculations of anelastic wave speeds at constant unloading strain rate are then compared with experimental data. The results suggest that the residual internal stress is due to pinned loops of density 10 15 M - 2 , and the viscous drag coefficient in the shock-compressed state is on the order of 10 - 7 MPa s (approximately two orders of magnitude greater than expected under ambient conditions)

Cell-like pressure sensors reveal increase of mechanical stress towards the core of multicellular spheroids under compression.

Science.gov (United States)

Dolega, M E; Delarue, M; Ingremeau, F; Prost, J; Delon, A; Cappello, G

2017-01-27

The surrounding microenvironment limits tumour expansion, imposing a compressive stress on the tumour, but little is known how pressure propagates inside the tumour. Here we present non-destructive cell-like microsensors to locally quantify mechanical stress distribution in three-dimensional tissue. Our sensors are polyacrylamide microbeads of well-defined elasticity, size and surface coating to enable internalization within the cellular environment. By isotropically compressing multicellular spheroids (MCS), which are spherical aggregates of cells mimicking a tumour, we show that the pressure is transmitted in a non-trivial manner inside the MCS, with a pressure rise towards the core. This observed pressure profile is explained by the anisotropic arrangement of cells and our results suggest that such anisotropy alone is sufficient to explain the pressure rise inside MCS composed of a single cell type. Furthermore, such pressure distribution suggests a direct link between increased mechanical stress and previously observed lack of proliferation within the spheroids core.

Development of in-situ rock shear test under low compressive to tensile normal stress

International Nuclear Information System (INIS)

Nozaki, Takashi; Shin, Koichi

2003-01-01

The purpose of this study is to develop an in-situ rock shear testing method to evaluate the shear strength under low normal stress condition including tensile stress, which is usually ignored in the assessment of safety factor of the foundations for nuclear power plants against sliding. The results are as follows. (1) A new in-situ rock shear testing method is devised, in which tensile normal stress can be applied on the shear plane of a specimen by directly pulling up a steel box bonded to the specimen. By applying the counter shear load to cancel the moment induced by the main shear load, it can obtain shear strength under low normal stress. (2) Some model tests on Oya tuff and diatomaceous mudstone have been performed using the developed test method. The shear strength changed smoothly from low values at tensile normal stresses to higher values at compressive normal stresses. The failure criterion has been found to be bi-linear on the shear stress vs normal stress plane. (author)

Distinct Trajectories of Cortisol Response to Prolonged Acute Stress Are Linked to Affective Responses and Hippocampal Gray Matter Volume in Healthy Females.

Science.gov (United States)

Admon, Roee; Treadway, Michael T; Valeri, Linda; Mehta, Malavika; Douglas, Samuel; Pizzagalli, Diego A

2017-08-16

The development of robust laboratory procedures for acute stress induction over the last decades has greatly advanced our understanding of stress responses in humans and their underlying neurobiological mechanisms. Nevertheless, attempts to uncover linear relationships among endocrine, neural, and affective responses to stress have generally yielded inconsistent results. Here, 79 healthy females completed a well established laboratory procedure of acute stress induction that was modified to prolong its effect. Endocrinological and subjective affect assessments revealed stress-induced increases in cortisol release and negative affect that persisted 65 and 100 min after stress onset, respectively, confirming a relatively prolonged acute stress induction. Applying latent class linear mixed modeling on individuals' patterns of cortisol responses identified three distinct trajectories of cortisol response: the hyper-response ( n = 10), moderate-response ( n = 21), and mild-response ( n = 48) groups. Notably, whereas all three groups exhibited a significant stress-induced increase in cortisol release and negative affect, the hyper-response and mild-response groups both reported more negative affect relative to the moderate-response group. Structural MRI revealed no group differences in hippocampal and amygdala volumes, yet a continuous measure of cortisol response (area under the curve) showed that high and low levels of stress-induced cortisol release were associated with less hippocampal gray matter volume compared with moderate cortisol release. Together, these results suggest that distinct trajectories of cortisol response to prolonged acute stress among healthy females may not be captured by conventional linear analyses; instead, quadratic relations may better describe links between cortisol response to stress and affective responses, as well as hippocampal structural variability. SIGNIFICANCE STATEMENT Despite substantial research, it is unclear whether and how

When Natural Disaster Follows Economic Downturn: The Incremental Impact of Multiple Stressor Events on Trajectories of Depression and Posttraumatic Stress Disorder.

Science.gov (United States)

Mandavia, Amar D; Bonanno, George A

2018-04-29

To determine whether there were incremental mental health impacts, specifically on depression trajectories, as a result of the 2008 economic crisis (the Great Recession) and subsequent Hurricane Sandy. Using latent growth mixture modeling and the ORANJ BOWL dataset, we examined prospective trajectories of depression among older adults (mean age, 60.67; SD, 6.86) who were exposed to the 2 events. We also collected community economic and criminal justice data to examine their impact upon depression trajectories. Participants (N=1172) were assessed at 3 times for affect, successful aging, and symptoms of depression. We additionally assessed posttraumatic stress disorder (PTSD) symptomology after Hurricane Sandy. We identified 3 prospective trajectories of depression. The majority (83.6%) had no significant change in depression from before to after these events (resilience), while 7.2% of the sample increased in depression incrementally after each event (incremental depression). A third group (9.2%) went from high to low depression symptomology following the 2 events (depressive-improving). Only those in the incremental depression group had significant PTSD symptoms following Hurricane Sandy. We identified a small group of individuals for whom the experience of multiple stressful events had an incremental negative effect on mental health outcomes. These results highlight the importance of understanding the perseveration of depression symptomology from one event to another. (Disaster Med Public Health Preparedness. 2018;page 1 of 10).

Stress transmission through Ti-Ni alloy, titanium and stainless steel in impact compression test.

Science.gov (United States)

Yoneyama, T; Doi, H; Kobayashi, E; Hamanaka, H; Tanabe, Y; Bonfield, W

2000-06-01

Impact stress transmission of Ti-Ni alloy was evaluated for biomedical stress shielding. Transformation temperatures of the alloy were investigated by means of DSC. An impact compression test was carried out with use of split-Hopkinson pressure-bar technique with cylindrical specimens of Ti-Ni alloy, titanium and stainless steel. As a result, the transmitted pulse through Ti-Ni alloy was considerably depressed as compared with those through titanium and stainless steel. The initial stress reduction was large through Ti-Ni alloy and titanium, but the stress reduction through Ti-Ni alloy was more continuous than titanium. The maximum value in the stress difference between incident and transmitted pulses through Ti-Ni alloy or titanium was higher than that through stainless steel, while the stress reduction in the maximum stress through Ti-Ni alloy was statistically larger than that through titanium or stainless steel. Ti-Ni alloy transmitted less impact stress than titanium or stainless steel, which suggested that the loading stress to adjacent tissues could be decreased with use of Ti-Ni alloy as a component material in an implant system. Copyright 2000 Kluwer Academic Publishers

Elastic stresses and plastic deformations in 'Santa Clara' tomato fruits caused by package dependent compression

Directory of Open Access Journals (Sweden)

PEREIRA ADRIANA VARGAS

2000-01-01

Full Text Available The objective of this work was to study the fruit compression behavior aiming to develop new tomato packages. Deformations caused by compression forces were observed inside packages and in individual 'Santa Clara' tomato fruit. The forces applied by a transparent acrylic lever to the fruit surface caused pericarp deformation and the flattened area was proportional to the force magnitude. The deformation was associated to the reduction in the gas volume (Vg, caused by expulsion of the air from the loculus cavity and reduction in the intercellular air volume of the pericarp. As ripening advanced, smaller fractions of the Vg reduced by the compressive force were restored after the stress was relieved. The lack of complete Vg restoration was an indication of permanent plastic deformations of the stressed cells. Vg regeneration (elastic recovery was larger in green fruits than in the red ones. The ratio between the applied force and the flattened area (flattening pressure, which depends on cell turgidity, decreased during ripening. Fruit movements associated with its depth in the container were observed during storage in a transparent glass container (495 x 355 x 220 mm. The downward movement of the fruits was larger in the top layers because these movements seem to be driven by a summation of the deformation of many fruits in all layers.

Allometric trajectories and "stress"

NARCIS (Netherlands)

Anfodillo, Tommaso; Petit, Giai; Sterck, Frank; Lechthaler, Silvia; Olson, Mark E.

2016-01-01

The term "stress" is an important but vague term in plant biology. We show situations in which thinking in terms of "stress" is profitably replaced by quantifying distance from functionally optimal scaling relationships between plant parts. These relationships include, for example, the

Effects of increasing the allowable compressive stress at release on the shear strength of prestressed concrete girders.

Science.gov (United States)

2008-09-01

In recent years, several research projects have been conducted to study the feasibility of increasing the allowable : compressive stress in concrete at prestress transfer, currently defined as 0.60f'ci in the AASHTO LRFD Bridge : Design Specification...

Trajectories of depressive symptoms among high risk African-American adolescents.

Science.gov (United States)

Repetto, Paula B; Caldwell, Cleopatra H; Zimmerman, Marc A

2004-12-01

To examine the trajectories of depressive symptoms among African-American youth and the psychosocial factors associated with these trajectories. The sample included 579 African-American adolescents who were at risk of dropping out of school, interviewed annually starting from ninth grade for 4 years. The measures included depressive symptoms, anxiety symptoms, self-esteem, stress, and active coping; all self-reported. We used cluster analysis to develop longitudinal trajectories of depression in our sample. Four different trajectories of depressive symptoms were found that represented the changes in depressive symptoms among the participants. These trajectories are: consistently high (15.9%), consistently low (21.1%), decreasing (41.8%), and increasing (21.2%) depressive symptoms. The results from the comparisons of the trajectories indicated that adolescents who presented consistently high levels of depressive symptoms were more likely to be female, reported more anxiety symptoms, lower self-esteem, higher stress, and lower grade point average (GPA) compared with adolescent members of the other trajectories. Depressive symptoms may be manifested in different ways according to the patterns of change. Different correlates are associated with these trajectories of depressive symptoms and provide insights about the antecedents and consequences of the patterns of change in depressive symptoms.

Influence of transverse compressive stress on Ic degradation of Ag alloy sheathed Bi-2223 tapes

International Nuclear Information System (INIS)

Oh, S S; Ha, D W; Ha, H S; Park, C; Kwon, Y K; Ryu, K S; Shin, H S

2004-01-01

In order to investigate the degradation of critical current (I c ) in the Ag alloy sheathed Bi-2223 tapes due to a transverse compressive stress introduced during manufacturing and operation of the HTS systems, a sample holder consisting of the upper block made of Ti alloy and the lower support plate made of glass fibre reinforced plastic was prepared. A shorter spacing of voltage taps caused large degradation of critical current with respect to compressive stress. It was found that the extent of the I c degradation is proportional to the initial critical current density of the tapes. Through the experiment optimizing the shape of voltage terminals and the pressing load for the continuous contact type 4-probe I c measurement system, it was found that the conical shape tip with large curvature radius was effective in suppressing the I c degradation in Bi-2223 tapes during the I c measurement. A hard alloy sheath of Ag-0.6wt%Mn was found to be quite tolerant to the I c degradation against the pressing load of voltage terminals

Modification of Flow Stress Curves and Constitutive Equations During Hot Compression Deformation of 5083 Aluminum Alloy

Directory of Open Access Journals (Sweden)

FU Ping

2017-08-01

Full Text Available The flow stress behavior of 5083 aluminum alloy was investigated under hot compression deformation at 523-723K,strain rates of 0.01-10s-1 and true strains of 0-0.7 with Gleeble-3800 thermal simulator. Based on the heat transfer effect on alloy deformation heat effect, the flow stress curves were corrected. The results show that influence of heat conduction can not be neglected and becomes more obvious with the increase of true strain. The corrected flow stress has little influence on the peak stress, but the steady flow stress softening trends to be diminished to some degree. The flow stress can be predicted by the Zener-Hollomon parameters in the constitutive equation. The corrected measured value exhibits a good agreement with the flow stress predicted by the constitutive equation, and the average relative error is only 5.21%.

QTAIM and Stress Tensor Characterization of Intramolecular Interactions Along Dynamics Trajectories of a Light-Driven Rotary Molecular Motor.

Science.gov (United States)

Wang, Lingling; Huan, Guo; Momen, Roya; Azizi, Alireza; Xu, Tianlv; Kirk, Steven R; Filatov, Michael; Jenkins, Samantha

2017-06-29

A quantum theory of atoms in molecules (QTAIM) and stress tensor analysis was applied to analyze intramolecular interactions influencing the photoisomerization dynamics of a light-driven rotary molecular motor. For selected nonadiabatic molecular dynamics trajectories characterized by markedly different S 1 state lifetimes, the electron densities were obtained using the ensemble density functional theory method. The analysis revealed that torsional motion of the molecular motor blades from the Franck-Condon point to the S 1 energy minimum and the S 1 /S 0 conical intersection is controlled by two factors: greater numbers of intramolecular bonds before the hop-time and unusually strongly coupled bonds between the atoms of the rotor and the stator blades. This results in the effective stalling of the progress along the torsional path for an extended period of time. This finding suggests a possibility of chemical tuning of the speed of photoisomerization of molecular motors and related molecular switches by reshaping their molecular backbones to decrease or increase the degree of coupling and numbers of intramolecular bond critical points as revealed by the QTAIM/stress tensor analysis of the electron density. Additionally, the stress tensor scalar and vector analysis was found to provide new methods to follow the trajectories, and from this, new insight was gained into the behavior of the S 1 state in the vicinity of the conical intersection.

Trajectories of maternal stress and anxiety from pregnancy to three years and child development at 3 years of age: Findings from the All Our Families (AOF) pregnancy cohort.

Science.gov (United States)

Mughal, Muhammad Kashif; Giallo, Rebecca; Arnold, Paul; Benzies, Karen; Kehler, Heather; Bright, Katherine; Kingston, Dawn

2018-07-01

Existing literature on maternal distress has focused on stress and anxiety during the pregnancy or postnatally and their relationship with child development. However, few studies have investigated the association between maternal stress and anxiety symptoms over time and child development in preschool children. The aim of this study was to examine the association between trajectories of maternal stress and anxiety symptoms from mid-pregnancy to three years postpartum and child development at age three years. Data were analyzed from 1983 mother-child dyads who participated in the three year follow-up of the All Our Families (AOF) study. Latent class analysis (LCA) was conducted to identify trajectories of women's stress and anxiety across from mid-pregnancy to three years postpartum. Multivariate logistic regression was used to explore the relationship between the stress and anxiety trajectories and child developmental delays while adjusting for the covariates. LCA identified three distinct trajectories of maternal stress and anxiety symptoms over time. Multivariate analysis showed mothers assigned to the high anxiety symptoms class had an increased risk (adjusted OR 2.80, 95% CI 2.80 (1.42 ─ 5.51), p = 0.003) of having a child with developmental delays at 3 years. The use of self-reported maternal mental health symptoms and no data on fathers' mental health are our study's limitations. The findings from a population-based Canadian sample provide empirical support for a relationship between maternal anxiety overtime and risk of child developmental delays. Identifying and supporting mothers experiencing high anxiety symptoms in the perinatal period may mitigate the risk of these delays in children. Copyright © 2018 Elsevier B.V. All rights reserved.

Inhomogeneous Relaxation of a Molecular Layer on an Insulator due to Compressive Stress

Science.gov (United States)

Bocquet, F.; Nony, L.; Mannsfeld, S. C. B.; Oison, V.; Pawlak, R.; Porte, L.; Loppacher, Ch.

2012-05-01

We discuss the inhomogeneous stress relaxation of a monolayer of hexahydroxytriphenylene (HHTP) which adopts the rare line-on-line (LOL) coincidence on KCl(001) and forms moiré patterns. The fact that the hexagonal HHTP layer is uniaxially compressed along the LOL makes this system an ideal candidate to discuss the influence of inhomogeneous stress relaxation. Our work is a combination of noncontact atomic force microscopy experiments, density functional theory and potential energy calculations, and a thorough interpretation by means of the Frenkel-Kontorova model. We show that the assumption of a homogeneous molecular layer is not valid for this organic-inorganic heteroepitaxial system since the best calculated energy configuration correlates with the experimental data only if inhomogeneous relaxations of the layer are taken into account.

Simulations of High Speed Fragment Trajectories

Science.gov (United States)

Yeh, Peter; Attaway, Stephen; Arunajatesan, Srinivasan; Fisher, Travis

2017-11-01

Flying shrapnel from an explosion are capable of traveling at supersonic speeds and distances much farther than expected due to aerodynamic interactions. Predicting the trajectories and stable tumbling modes of arbitrary shaped fragments is a fundamental problem applicable to range safety calculations, damage assessment, and military technology. Traditional approaches rely on characterizing fragment flight using a single drag coefficient, which may be inaccurate for fragments with large aspect ratios. In our work we develop a procedure to simulate trajectories of arbitrary shaped fragments with higher fidelity using high performance computing. We employ a two-step approach in which the force and moment coefficients are first computed as a function of orientation using compressible computational fluid dynamics. The force and moment data are then input into a six-degree-of-freedom rigid body dynamics solver to integrate trajectories in time. Results of these high fidelity simulations allow us to further understand the flight dynamics and tumbling modes of a single fragment. Furthermore, we use these results to determine the validity and uncertainty of inexpensive methods such as the single drag coefficient model.

Compressions of electrorheological fluids under different initial gap distances.

Science.gov (United States)

Tian, Yu; Wen, Shizhu; Meng, Yonggang

2003-05-01

Compressions of electrorheological (ER) fluids have been carried out under different initial gap distances and different applied voltages. The nominal yield stresses of the compressed ER fluid under different conditions, according to the mechanics of compressing continuous fluids considering the yield stress of the plastic fluid, have been calculated. Curves of nominal yield stress under different applied voltages at an initial gap distance of 4 mm overlapped well and were shown to be proportional to the square of the external electric field and agree well with the traditional description. With the decrease of the initial gap distance, the difference between the nominal yield stress curves increased. The gap distance effect on the compression of ER fluids could not be explained by the traditional description based on the Bingham model and the continuous media theory. An explanation based on the mechanics of particle chain is proposed to describe the gap distance effect on the compression of ER fluids.

Failure behaviour of carbon/carbon composite under compression

Energy Technology Data Exchange (ETDEWEB)

Tushtev, K.; Grathwohl, G. [Universitaet Bremen, Advanced Ceramics, Bremen (Germany); Koch, D. [Deutsches Zentrum fuer Luft- und Raumfahrt, Institut fuer Bauweisen- und Konstruktionsforschung, Keramische Verbundstrukturen, Stuttgart (Germany); Horvath, J.

2012-11-15

In this work the properties of Carbon/Carbon-material are investigated under quasi-static compression and model-like characterized. The investigated material was produced by pyrolysis of a Carbon/Carbon - composite of bidirectionally reinforced fabric layers. For the compression tests, a device to prevent additional bending stress was made. The stress-strain behaviour of this material has been reproduced in various publications. This will be discussed on the fracture behaviour and compared the experimental results from the compression tests with the characteristics of tensile and shear tests. The different compression and tensile properties of stiffness, poisson and strength were assessed. Differences between the tensile and compression behaviour resulting from on-axis tests by micro buckling and crack closure and off-axis experiments by superimposed pressure normal stresses that lead to increased shear friction. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Comorbidity amplifies the effects of post-9/11 posttraumatic stress disorder trajectories on health-related quality of life.

Science.gov (United States)

Li, Jiehui; Zweig, Kimberly Caramanica; Brackbill, Robert M; Farfel, Mark R; Cone, James E

2018-03-01

The present study aims to examine the impact of physical and mental health comorbidities on the association between post-9/11 posttraumatic stress disorder (PTSD) trajectories over 10 years and health-related quality of life (HRQOL) among 9/11-exposed persons. 30,002 responding adult World Trade Center Health Registry enrollees reporting no pre-9/11 PTSD were studied. PTSD trajectories (chronic, delayed, remitted, no PTSD) were defined based on a 17-item PTSD Checklist-Specific to 9/11 across three waves of survey data. Three indicators of poor HRQOL were defined based on CDC HRQOL-4 measures. We computed age-adjusted prevalence of physical and mental health comorbidity (depression/anxiety) by PTSD trajectory and used modified Poisson regression to assess the effect of PTSD trajectory on poor HRQOL prevalence, accounting for comorbidity. Age-adjusted prevalence of overall comorbid conditions was 95.8 and 61.4% among the chronic and no-PTSD groups, respectively. Associations between 9/11-related PTSD trajectories and poor HRQOL were significant and became greater when comorbidity was included. Adjusted prevalence ratios were elevated for fair/poor health status (APR 7.3, 95% CI 6.5, 8.2), ≥ 14 unhealthy days (4.7; 95% CI 4.4, 5.1), and ≥ 14 activity limitation days during the last 30 days (9.6; 95% CI 8.1, 11.4) in the chronic PTSD group with physical and mental health comorbidity compared to those without PTSD and comorbidity; similar associations were observed for delayed PTSD. Ten years post-9/11 physical and mental health comorbidities have a substantial impact on the PTSD trajectories and HRQOL association. The need for early identification and treatment of PTSD and comorbidity should be emphasized to potentially improve HRQOL.

Longitudinal Study of Headache Trajectories in the Year After Mild Traumatic Brain Injury: Relation to Posttraumatic Stress Disorder Symptoms.

Science.gov (United States)

Sawyer, Kathryn; Bell, Kathleen R; Ehde, Dawn M; Temkin, Nancy; Dikmen, Sureyya; Williams, Rhonda M; Dillworth, Tiara; Hoffman, Jeanne M

2015-11-01

To examine headache trajectories among persons with mild traumatic brain injury (MTBI) in the year after injury and the relation of headache trajectory to posttraumatic stress disorder (PTSD) at 1 year postinjury. Prospective, longitudinal study. Participants were recruited through a university medical center and participated in follow-up assessments by telephone. Prospectively enrolled individuals (N=212) within 1 week of MTBI who were hospitalized for observation or other system injuries. Participants were assessed at baseline and 3, 6, and 12 months postinjury. Not applicable. Participants rated average headache pain intensity using the 0 to 10 numerical rating scale at each assessment period. The PTSD Checklist-Civilian Version was completed at 12 months postinjury. Latent class growth analysis produced a 4-trajectory group model, with groups labeled resolved, worsening, improving, and chronic. Multivariate regression modeling revealed that younger age and premorbid headache correlated with membership in the worse trajectory groups (worsening and chronic; PHeadache is common in the year after MTBI, with younger people, persons who previously had headaches, and persons with PTSD more likely to report chronic or worsening headache. Further research is needed to examine whether PTSD symptoms exacerbate headaches or whether problematic headache symptoms exacerbate PTSD. Copyright © 2015 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Dynamic compressive properties and failure mechanism of glass fiber reinforced silica hydrogel

International Nuclear Information System (INIS)

Yang Jie; Li Shukui; Yan Lili; Huo Dongmei; Wang Fuchi

2010-01-01

The dynamic compressive properties of glass fiber reinforced silica (GFRS) hydrogel were investigated using a spilt Hopkinson pressure bar. Failure mechanism of GFRS hydrogel was studied by scanning electron microscopy (SEM). Result showed that dynamic compressive stresses were much higher than the quasi-static compressive stresses at the same strain. The dynamic compressive strength was directly proportional to the strain rate with same sample dimensions. The dynamic compressive strength was directly proportional to the sample basal area at same strain rate. Dynamic compressive failure strain was small. At high strain rates, glass fibers broke down and separated from the matrix, pores shrank rapidly. Failure resulted from the increase of lateral tensile stress in hydrogel under dynamic compression.

Predicting guar seed splitting by compression between two plates using Hertz theory of contact stresses.

Science.gov (United States)

Vishwakarma, R K; Shivhare, U S; Nanda, S K

2012-09-01

Hertz's theory of contact stresses was applied to predict the splitting of guar seeds during uni-axial compressive loading between 2 rigid parallel plates. The apparent modulus of elasticity of guar seeds varied between 296.18 and 116.19 MPa when force was applied normal to hilum joint (horizontal position), whereas it varied between 171.86 and 54.18 MPa when force was applied in the direction of hilum joint (vertical position) with in moisture content range of 5.16% to 15.28% (d.b.). At higher moisture contents, the seeds yielded after considerable deformation, thus showing ductile nature. Distribution of stresses below the point of contact were plotted to predict the location of critical point, which was found at 0.44 to 0.64 mm and 0.37 to 0.53 mm below the contact point in vertical and horizontal loading, respectively, depending upon moisture content. The separation of cotyledons from each other initiated before yielding of cotyledons and thus splitting of seed took place. The relationships between apparent modulus of elasticity, principal stresses with moisture content were described using second-order polynomial equations and validated experimentally. Manufacture of guar gum powder requires dehulling and splitting of guar seeds. This article describes splitting behavior of guar seeds under compressive loading. Results of this study may be used for design of dehulling and splitting systems of guar seeds. © 2012 Institute of Food Technologists®

A measurement method for piezoelectric material properties under longitudinal compressive stress–-a compression test method for thin piezoelectric materials

International Nuclear Information System (INIS)

Kang, Lae-Hyong; Lee, Dae-Oen; Han, Jae-Hung

2011-01-01

We introduce a new compression test method for piezoelectric materials to investigate changes in piezoelectric properties under the compressive stress condition. Until now, compression tests of piezoelectric materials have been generally conducted using bulky piezoelectric ceramics and pressure block. The conventional method using the pressure block for thin piezoelectric patches, which are used in unimorph or bimorph actuators, is prone to unwanted bending and buckling. In addition, due to the constrained boundaries at both ends, the observed piezoelectric behavior contains boundary effects. In order to avoid these problems, the proposed method employs two guide plates with initial longitudinal tensile stress. By removing the tensile stress after bonding a piezoelectric material between the guide layers, longitudinal compressive stress is induced in the piezoelectric layer. Using the compression test specimens, two important properties, which govern the actuation performance of the piezoelectric material, the piezoelectric strain coefficients and the elastic modulus, are measured to evaluate the effects of applied electric fields and re-poling. The results show that the piezoelectric strain coefficient d 31 increases and the elastic modulus decreases when high voltage is applied to PZT5A, and the compression in the longitudinal direction decreases the piezoelectric strain coefficient d 31 but does not affect the elastic modulus. We also found that the re-poling of the piezoelectric material increases the elastic modulus, but the piezoelectric strain coefficient d 31 is not changed much (slightly increased) by re-poling

Lagrangian statistics in compressible isotropic homogeneous turbulence

Science.gov (United States)

Yang, Yantao; Wang, Jianchun; Shi, Yipeng; Chen, Shiyi

2011-11-01

In this work we conducted the Direct Numerical Simulation (DNS) of a forced compressible isotropic homogeneous turbulence and investigated the flow statistics from the Lagrangian point of view, namely the statistics is computed following the passive tracers trajectories. The numerical method combined the Eulerian field solver which was developed by Wang et al. (2010, J. Comp. Phys., 229, 5257-5279), and a Lagrangian module for tracking the tracers and recording the data. The Lagrangian probability density functions (p.d.f.'s) have then been calculated for both kinetic and thermodynamic quantities. In order to isolate the shearing part from the compressing part of the flow, we employed the Helmholtz decomposition to decompose the flow field (mainly the velocity field) into the solenoidal and compressive parts. The solenoidal part was compared with the incompressible case, while the compressibility effect showed up in the compressive part. The Lagrangian structure functions and cross-correlation between various quantities will also be discussed. This work was supported in part by the China's Turbulence Program under Grant No.2009CB724101.

β-distribution for Reynolds stress and turbulent heat flux in relaxation turbulent boundary layer of compression ramp

Science.gov (United States)

Hu, YanChao; Bi, WeiTao; Li, ShiYao; She, ZhenSu

2017-12-01

A challenge in the study of turbulent boundary layers (TBLs) is to understand the non-equilibrium relaxation process after sep-aration and reattachment due to shock-wave/boundary-layer interaction. The classical boundary layer theory cannot deal with the strong adverse pressure gradient, and hence, the computational modeling of this process remains inaccurate. Here, we report the direct numerical simulation results of the relaxation TBL behind a compression ramp, which reveal the presence of intense large-scale eddies, with significantly enhanced Reynolds stress and turbulent heat flux. A crucial finding is that the wall-normal profiles of the excess Reynolds stress and turbulent heat flux obey a β-distribution, which is a product of two power laws with respect to the wall-normal distances from the wall and from the boundary layer edge. In addition, the streamwise decays of the excess Reynolds stress and turbulent heat flux also exhibit power laws with respect to the streamwise distance from the corner of the compression ramp. These results suggest that the relaxation TBL obeys the dilation symmetry, which is a specific form of self-organization in this complex non-equilibrium flow. The β-distribution yields important hints for the development of a turbulence model.

Electrochemical behavior of single-walled carbon nanotube supercapacitors under compressive stress.

Science.gov (United States)

Li, Xin; Rong, Jiepeng; Wei, Bingqing

2010-10-26

The effect of compressive stress on the electrochemical behavior of flexible supercapacitors assembled with single-walled carbon nanotube (SWNT) film electrodes and 1 M aqueous electrolytes with different anions and cations were thoroughly investigated. The under-pressed capacitive and resistive features of the supercapacitors were studied by means of cyclic voltammetry measurements and electrochemical impedance analysis. The results demonstrated that the specific capacitance increased first and saturated in corresponding decreases of the series resistance, the charge-transfer resistance, and the Warburg diffusion resistance under an increased pressure from 0 to 1723.96 kPa. Wettability as well as ion-size effect of different aqueous electrolytes played important roles to determine the pressure dependence behavior of the suerpcapacitors under an applied pressure. An improved high-frequency capacitive response with 1172 Hz knee frequency, which is significantly higher compared to reported values, was observed under the compressive pressure of 1723.96 kPa, indicating an improving and excellent high-power capability of the supercapacitors under the pressure. The experimental results and the thorough analysis described in this work not only provide fundamental insight of pressure effects on supercapacitors but also give an important guideline for future design of next generation flexible/stretchable supercapacitors for industrial and consumer applications.

Development of the apparatus for measuring magnetic properties of electrical steel sheets in arbitrary directions under compressive stress normal to their surface

Science.gov (United States)

Maeda, Yoshitaka; Urata, Shinya; Nakai, Hideo; Takeuchi, Yuuya; Yun, Kyyoul; Yanase, Shunji; Okazaki, Yasuo

2017-05-01

In designing motors, one must grasp the magnetic properties of electrical steel sheets considering actual conditions in motors. Especially important is grasping the stress dependence of magnetic power loss. This paper describes a newly developed apparatus to measure two-dimensional (2-D) magnetic properties (properties under the arbitrary alternating and the rotating flux conditions) of electrical steel sheets under compressive stress normal to the sheet surface. The apparatus has a 2-D magnetic excitation circuit to generate magnetic fields in arbitrary directions in the evaluation area. It also has a pressing unit to apply compressive stress normal to the sheet surface. During measurement, it is important to apply uniform stress throughout the evaluation area. Therefore, we have developed a new flux density sensor using needle probe method. It is composed of thin copper foils sputtered on electrical steel sheets. By using this sensor, the stress can be applied to the surface of the specimen without influence of this sensor. This paper described the details of newly developed apparatus with this sensor, and measurement results of iron loss by using are shown.

Influence of applied compressive stress on the hysteresis curves and magnetic domain structure of grain-oriented transverse Fe-3%Si steel

International Nuclear Information System (INIS)

Perevertov, O; Schäfer, R

2012-01-01

The influence of an applied compressive stress on the hysteresis curve and domain structure in conventional (1 1 0) [0 0 1] Fe-3%Si steel cut transverse to the rolling direction is studied. Quasistatic hysteresis loops under compressive stress up to 75 MPa were measured. The magnetic domains and magnetization processes were observed by longitudinal Kerr microscopy at different levels of stress. It is shown that the bulk hysteresis loop can be described with a good accuracy by the action of an effective field, which is the product of the stress and a function of magnetization. Domain observations have shown that the reasons for the effective field are demagnetizing fields due to the disappearance of supplementary domains along [0 1 0] and [1 0 0] at low fields and different domain systems in different grains at moderate fields. The latter are caused by differences in grain sensitivity to stress depending on the degree of misorientation. A decrease in the effective field above 1 T is connected with a transformation of all grains into the same domain system—the column pattern. (paper)

Effects of applied stress ratio on the fatigue behavior of additively manufactured porous biomaterials under compressive loading.

Science.gov (United States)

de Krijger, Joep; Rans, Calvin; Van Hooreweder, Brecht; Lietaert, Karel; Pouran, Behdad; Zadpoor, Amir A

2017-06-01

Additively manufactured (AM) porous metallic biomaterials are considered promising candidates for bone substitution. In particular, AM porous titanium can be designed to exhibit mechanical properties similar to bone. There is some experimental data available in the literature regarding the fatigue behavior of AM porous titanium, but the effect of stress ratio on the fatigue behavior of those materials has not been studied before. In this paper, we study the effect of applied stress ratio on the compression-compression fatigue behavior of selective laser melted porous titanium (Ti-6Al-4V) based on the diamond unit cell. The porous titanium biomaterial is treated as a meta-material in the context of this work, meaning that R-ratios are calculated based on the applied stresses acting on a homogenized volume. After morphological characterization using micro computed tomography and quasi-static mechanical testing, the porous structures were tested under cyclic loading using five different stress ratios, i.e. R = 0.1, 0.3, 0.5, 0.7 and 0.8, to determine their S-N curves. Feature tracking algorithms were used for full-field deformation measurements during the fatigue tests. It was observed that the S-N curves of the porous structures shift upwards as the stress ratio increases. The stress amplitude was the most important factor determining the fatigue life. Constant fatigue life diagrams were constructed and compared with similar diagrams for bulk Ti-6Al-4V. Contrary to the bulk material, there was limited dependency of the constant life diagrams to mean stress. The notches present in the AM biomaterials were the sites of crack initiation. This observation and other evidence suggest that the notches created by the AM process cause the insensitivity of the fatigue life diagrams to mean stress. Feature tracking algorithms visualized the deformation during fatigue tests and demonstrated the root cause of inclined (45°) planes of specimen failure. In conclusion, the R

Compression behavior of a ferritic-martensitic Cr-Mo steel

DEFF Research Database (Denmark)

Zhang, Zhenbo; Mishin, Oleg; Pantleon, Wolfgang

2012-01-01

The compression behavior of a ferritic-martensitic Cr-Mo steel is characterized for strain rates ranging from 10-4 s-1 to 10-1 s-1 and engineering strains up to 40%. Adiabatic heating causes a reduction in flow stress during continuous compression at a strain rate of 10-1 s-1. No reduction...... in the flow stress is observed if interrupted compression tests are performed with loading and holding steps. Two work-hardening stages with work-hardening rates decreasing linearly with the flow stress are identified and interpreted in terms of the KocksMecking model. The microstructural evolution...

Cortisol responses to psychosocial stress predict depression trajectories: social-evaluative threat and prior depressive episodes as moderators.

Science.gov (United States)

Morris, Matthew C; Rao, Uma; Garber, Judy

2012-12-20

Alterations of hypothalamic-pituitary-adrenal (HPA) function are well-established in adults with current depression. HPA alterations may persist into remission and confer increased risk for recurrence. A modified version of the Trier Social Stress Test (TSST) was administered at baseline to 32 young adults with remitted major depressive disorder and 36 never-depressed controls. Participants were randomly assigned to either a 'high-stress' condition involving social evaluation or a 'low-stress' control condition. Cortisol concentrations were measured in saliva samples throughout the TSST. Participants were assessed again after 6 months for the occurrence of stressful life events and depressive symptoms/disorders during the follow-up period. Participants who exhibited enhanced cortisol reactivity in the low-stress condition showed increases in depressive symptoms over follow-up, after controlling for stressful life events during the follow-up period. Anticipatory stress cortisol and cortisol reactivity each interacted with history of depressive episodes to predict depression trajectories. The single TSST administration limits conclusions about whether alterations of cortisol reactivity represent trait-like vulnerability factors or consequences ("scars') of past depression. These results extend previous findings on stress sensitivity in depression and suggest that altered HPA function during remission could reflect an endophenotype for vulnerability to depression recurrence. Findings support interactive models of risk for depression recurrence implicating HPA function, depression history, and sensitivity to minor stressors. Results may have implications for interventions that match treatment approaches to profiles of HPA function. Copyright © 2012 Elsevier B.V. All rights reserved.

On Compression of a Heavy Compressible Layer of an Elastoplastic or Elastoviscoplastic Medium

Science.gov (United States)

Kovtanyuk, L. V.; Panchenko, G. L.

2017-11-01

The problem of deformation of a horizontal plane layer of a compressible material is solved in the framework of the theory of small strains. The upper boundary of the layer is under the action of shear and compressing loads, and the no-slip condition is satisfied on the lower boundary of the layer. The loads increase in absolute value with time, then become constant, and then decrease to zero.Various plasticity conditions are consideredwith regard to the material compressibility, namely, the Coulomb-Mohr plasticity condition, the von Mises-Schleicher plasticity condition, and the same conditions with the viscous properties of the material taken into account. To solve the system of partial differential equations for the components of irreversible strains, a finite-difference scheme is developed for a spatial domain increasing with time. The laws of motion of elastoplastic boundaries are presented, the stresses, strains, rates of strain, and displacements are calculated, and the residual stresses and strains are found.

Compressive behavior of fine sand.

Energy Technology Data Exchange (ETDEWEB)

Martin, Bradley E. (Air Force Research Laboratory, Eglin, FL); Kabir, Md. E. (Purdue University, West Lafayette, IN); Song, Bo; Chen, Wayne (Purdue University, West Lafayette, IN)

2010-04-01

The compressive mechanical response of fine sand is experimentally investigated. The strain rate, initial density, stress state, and moisture level are systematically varied. A Kolsky bar was modified to obtain uniaxial and triaxial compressive response at high strain rates. A controlled loading pulse allows the specimen to acquire stress equilibrium and constant strain-rates. The results show that the compressive response of the fine sand is not sensitive to strain rate under the loading conditions in this study, but significantly dependent on the moisture content, initial density and lateral confinement. Partially saturated sand is more compliant than dry sand. Similar trends were reported in the quasi-static regime for experiments conducted at comparable specimen conditions. The sand becomes stiffer as initial density and/or confinement pressure increases. The sand particle size become smaller after hydrostatic pressure and further smaller after dynamic axial loading.

Development of the apparatus for measuring magnetic properties of electrical steel sheets in arbitrary directions under compressive stress normal to their surface

Directory of Open Access Journals (Sweden)

Yoshitaka Maeda

2017-05-01

Full Text Available In designing motors, one must grasp the magnetic properties of electrical steel sheets considering actual conditions in motors. Especially important is grasping the stress dependence of magnetic power loss. This paper describes a newly developed apparatus to measure two-dimensional (2-D magnetic properties (properties under the arbitrary alternating and the rotating flux conditions of electrical steel sheets under compressive stress normal to the sheet surface. The apparatus has a 2-D magnetic excitation circuit to generate magnetic fields in arbitrary directions in the evaluation area. It also has a pressing unit to apply compressive stress normal to the sheet surface. During measurement, it is important to apply uniform stress throughout the evaluation area. Therefore, we have developed a new flux density sensor using needle probe method. It is composed of thin copper foils sputtered on electrical steel sheets. By using this sensor, the stress can be applied to the surface of the specimen without influence of this sensor. This paper described the details of newly developed apparatus with this sensor, and measurement results of iron loss by using are shown.

Evaluation of polymerization shrinkage, polymerization shrinkage stress, wear resistance, and compressive strength of a silorane-based composite: A finite element analysis study

Directory of Open Access Journals (Sweden)

Suresh Mitthra

2017-01-01

Full Text Available Background: Understanding the mechanical properties is important in predicting the clinical behavior of composites. Finite element analysis (FEA evaluates properties of materials replicating clinical scenario. Aim: This study evaluated polymerization shrinkage and stress, wear resistance (WR, and compressive strength (CS of silorane in comparison with two methacrylate resins. Settings and Design: This study design was a numerical study using FEA. Materials and Methods: Three-dimensional (3D models of maxillary premolar with Class I cavities (2 mm depth, 4 mm length, and 2.5 mm width created and restored with silorane, nanohybrid, and microhybrid; Groups I, II, and III, respectively. Loads of 200–600 N were applied. Polymerization shrinkage was first determined by displacement produced in the X, Y, and Z planes. Maximum stress distribution due to shrinkage was calculated using AN SYS software. 3D cube models of composite resins were simulated with varying filler particle size. Similar loads were applied. WR and compressive stress were calculated: K W L/H and load/cross-sectional area, respectively. Statistical analysis done using one-way ANOVA, Kruskal–Wallis, and Tukey's honestly significant difference test (P < 0.05. Results: Polymerization shrinkage (0.99% and shrinkage stress (233.21 Mpa of silorane were less compared to microhybrid (2.14% and 472.43 Mpa and nanohybrid (2.32% and 464.88 Mpa. Silorane (7.92×/1011 μm/mm3 and nanohybrid (7.79×/1011 showed superior WR than microhybrid (1.113×/1017. There was no significant difference in compressive stress among the groups. Conclusion: Silorane exhibited less polymerization shrinkage and shrinkage stress compared to methacrylates. Silorane and nanohybrid showed greater WR compared to microhybrid. CS of all groups was similar.

Response of notched AS4/PEEK laminates to tension/compression loading

Science.gov (United States)

Simonds, Robert A.; Stinchcomb, Wayne W.

1989-01-01

Fatigue life, damage-initiation and propagation, and residual strength data are presently examined to ascertain the response of notched AS4/PEEK specimens to fully reversed tension/compression loading. Stiffness measurements made during the low-level fatigue history show that compression stiffness and tension stiffness degrade throughout the fatigue life. Damage to specimens fatigued at higher cyclic stresses developed primarily in the direction perpendicular to the loading. As in the case of specimens fatigued at lower stress levels, residual compressive stress decreased with damage development.

High level compressive residual stresses produced in aluminum alloys by laser shock processing

International Nuclear Information System (INIS)

Gomez-Rosas, G.; Rubio-Gonzalez, C.; Ocana, J.L; Molpeceres, C.; Porro, J.A.; Chi-Moreno, W.; Morales, M.

2005-01-01

Laser shock processing (LSP) has been proposed as a competitive alternative technology to classical treatments for improving fatigue and wear resistance of metals. We present a configuration and results for metal surface treatments in underwater laser irradiation at 1064 nm. A convergent lens is used to deliver 1.2 J/cm 2 in a 8 ns laser FWHM pulse produced by 10 Hz Q-switched Nd:YAG, two laser spot diameters were used: 0.8 and 1.5 mm. Results using pulse densities of 2500 pulses/cm 2 in 6061-T6 aluminum samples and 5000 pulses/cm 2 in 2024 aluminum samples are presented. High level of compressive residual stresses are produced -1600 MPa for 6061-T6 Al alloy, and -1400 MPa for 2024 Al alloy. It has been shown that surface residual stress level is higher than that achieved by conventional shot peening and with greater depths. This method can be applied to surface treatment of final metal products

Particular mechanism for continuously varying the compression ratio for an internal combustion engine

Science.gov (United States)

Raţiu, S.; Cătălinoiu, R.; Alexa, V.; Miklos, I.; Cioată, V.

2018-01-01

Variable compression ratio (VCR) is a technology to adjust the compression ratio of an internal combustion engine while the engine is in operation. The paper proposes the presentation of a particular mechanism allowing the position of the top dead centre to be changed, while the position of the bottom dead centre remains fixed. The kinematics of the mechanism is studied and its trajectories are graphically represented for different positions of operation.

SharkDB: an in-memory column-oriented storage for trajectory analysis

KAUST Repository

Zheng, Bolong; Wang, Haozhou; Zheng, Kai; Su, Han; Liu, Kuien; Shang, Shuo

2017-01-01

The last decade has witnessed the prevalence of sensor and GPS technologies that produce a high volume of trajectory data representing the motion history of moving objects. However some characteristics of trajectories such as variable lengths and asynchronous sampling rates make it difficult to fit into traditional database systems that are disk-based and tuple-oriented. Motivated by the success of column store and recent development of in-memory databases, we try to explore the potential opportunities of boosting the performance of trajectory data processing by designing a novel trajectory storage within main memory. In contrast to most existing trajectory indexing methods that keep consecutive samples of the same trajectory in the same disk page, we partition the database into frames in which the positions of all moving objects at the same time instant are stored together and aligned in main memory. We found this column-wise storage to be surprisingly well suited for in-memory computing since most frames can be stored in highly compressed form, which is pivotal for increasing the memory throughput and reducing CPU-cache miss. The independence between frames also makes them natural working units when parallelizing data processing on a multi-core environment. Lastly we run a variety of common trajectory queries on both real and synthetic datasets in order to demonstrate advantages and study the limitations of our proposed storage.

SharkDB: an in-memory column-oriented storage for trajectory analysis

KAUST Repository

Zheng, Bolong

2017-05-05

The last decade has witnessed the prevalence of sensor and GPS technologies that produce a high volume of trajectory data representing the motion history of moving objects. However some characteristics of trajectories such as variable lengths and asynchronous sampling rates make it difficult to fit into traditional database systems that are disk-based and tuple-oriented. Motivated by the success of column store and recent development of in-memory databases, we try to explore the potential opportunities of boosting the performance of trajectory data processing by designing a novel trajectory storage within main memory. In contrast to most existing trajectory indexing methods that keep consecutive samples of the same trajectory in the same disk page, we partition the database into frames in which the positions of all moving objects at the same time instant are stored together and aligned in main memory. We found this column-wise storage to be surprisingly well suited for in-memory computing since most frames can be stored in highly compressed form, which is pivotal for increasing the memory throughput and reducing CPU-cache miss. The independence between frames also makes them natural working units when parallelizing data processing on a multi-core environment. Lastly we run a variety of common trajectory queries on both real and synthetic datasets in order to demonstrate advantages and study the limitations of our proposed storage.

Involvement of upper torso stress amplification, tissue compression and distortion in the pathogenesis of keloids.

Science.gov (United States)

Bux, Shamin; Madaree, Anil

2012-03-01

Keloids are benign tumours composed of fibrous tissue produced during excessive tissue repair triggered by minor injury, trauma or surgical incision. Although it is recognized that keloids have a propensity to form in the upper torso of the body, the predisposing factors responsible for this have not been investigated. It is crucial that the aetiopathoical factors implicated in keloid formation be established to provide guidelines for well-informed more successful treatment. We compared keloid-prone and keloid-protected skin, identified pertinent morphological differences and explored how inherent structural characteristics and intrinsic factors may promote keloid formation. It was determined that keloid prone areas were covered with high tension skin that had low stretch and a low elastic modulus when compared with skin in keloid protected areas where the skin was lax with a high elastic modulus and low pre-stress level. Factors contributing to elevated internal stress in keloid susceptible skin were the protrusion of hard connective tissue such as bony prominences or cartilage into the dermis of skin as well as inherent skin characteristics such as the bundled arrangement of collagen in the reticular dermis, the existent high tension, the low elastic modulus, low stretch ability, contractile forces exerted by wound healing fibroblastic cells and external forces. Stress promotes keloid formation by causing dermal distortion and compression which subsequently stimulate proliferation and enhanced protein synthesis in wound healing fibroblastic cells. The strain caused by stress also compresses and occludes microvessels causing ischaemic effects and reperfusion injury which stimulate growth when blood rich in growth factors returns to the tissue. The growth promoting effects of increased internal stress, primarily, and growth factors released by reperfusing blood, manifest in keloid formation. Other inherent skin characteristics promoting keloid growth during the

Markers of Oxidative Stress in Human Milk do not Differ by Maternal BMI But are Related to Infant Growth Trajectories.

Science.gov (United States)

Young, Bridget E; Patinkin, Zachary W; Pyle, Laura; de la Houssaye, Becky; Davidson, Barbara S; Geraghty, Sheela; Morrow, Ardythe L; Krebs, Nancy

2017-06-01

Objective Obesity in adults is associated with inflammation and oxidative stress. Whether or not this phenotype is reflected in human milk (HM) composition, or may impact infant growth remains unknown. We investigated whether HM from overweight/obese (OW/Ob) mothers exhibited higher concentrations of inflammatory cytokines and markers of oxidative stress. We also correlated these bioactive components with infant growth patterns. Methods This was an observational cohort of 56 breastfeeding mothers and their infants [33 normal weight (NW) and 23 OW/Ob]. Infants were followed until 6 months of age and HM collected at 2-weeks and 4-months. Results Markers of oxidative stress, 8-hydroxy-deoxyguanosine (8OHdG) and 4-hydroxynonenol (HNE), decreased in HM over time (p < 0.001) and did not differ between NW and OW/Ob women. Concentrations of inflammatory cytokines, IL-6, IL-8, and TNF-α, were all inter-correlated (p < 0.001) but did not differ between NW and OW/Ob women. HM fat, protein, lactose, and total calories did not differ between NW and OW/Ob women. Infant growth patterns did not differ by group. In a model of infant weight-for-length-Z score trajectory, there was a significant interaction between both lactose and 8OHdG with maternal group: HM lactose and 8OHdG concentrations were both positively associated with increases in WLZ trajectory only among infants breastfed by OW/Ob mothers. Conclusions for Practice HM composition was relatively stable between NW and OW/Ob women. In exclusively breastfed infants, HM concentrations of lactose and 8OHdG, a marker of oxidative stress, may contribute to regulation of infant weight gain, especially among infants of OW/Ob women.

Comparison of Open-Hole Compression Strength and Compression After Impact Strength on Carbon Fiber/Epoxy Laminates for the Ares I Composite Interstage

Science.gov (United States)

Hodge, Andrew J.; Nettles, Alan T.; Jackson, Justin R.

2011-01-01

Notched (open hole) composite laminates were tested in compression. The effect on strength of various sizes of through holes was examined. Results were compared to the average stress criterion model. Additionally, laminated sandwich structures were damaged from low-velocity impact with various impact energy levels and different impactor geometries. The compression strength relative to damage size was compared to the notched compression result strength. Open-hole compression strength was found to provide a reasonable bound on compression after impact.

Tensile and compressive behavior of Borsic/aluminum

Science.gov (United States)

Herakovich, C. T.; Davis, J. G., Jr.; Viswanathan, C. N.

1977-01-01

The results of an experimental investigation of the mechanical behavior of Borsic/aluminum are presented. Composite laminates were tested in tension and compression for monotonically increasing load and also for variable loading cycles in which the maximum load was increased in each successive cycle. It is shown that significant strain-hardening, and corresponding increase in yield stress, is exhibited by the metal matrix laminates. For matrix dominated laminates, the current yield stress is essentially identical to the previous maximum stress, and unloading is essentially linear with large permanent strains after unloading. For laminates with fiber dominated behavior, the yield stress increases with increase in the previous maximum stress, but the increase in yield stress does not keep pace with the previous maximum stress. These fiber dominated laminates exhibit smaller nonlinear strains, reversed nonlinear behavior during unloading, and smaller permanent strains after unloading. Compression results from sandwich beams and flat coupons are shown to differ considerably. Results from beam specimens tend to exhibit higher values for modulus, yield stress, and strength.

Compression characteristics and permeability of saturated Gaomiaozi ca-bentonite

International Nuclear Information System (INIS)

Sun Wenjing; Sun De'an; Fang Lei

2012-01-01

The compression characteristics and permeability of compacted Gaomiaozi Ca-bentonite saturated by the water uptake tests are studied by conducting a series of one-dimension compression tests. The permeability coefficient can be calculated by the Terzaghi's one-dimensional consolidation theory after the consolidation coefficient is obtained by the square root of time method. It is found that the compression curves of compacted specimens saturated by the water uptake tests tend to be consistent in the relatively high stress range. The compression indexes show a linear decrease with increasing dry density and the swelling index is a constant. The permeability coefficient decreases with increasing compression stress, and they show the linear relationship in double logarithmic coordinates. Meanwhile, the permeability coefficient shows a linear decrease with decreasing void ratio, which has no relationship with initial states, stress states and stress paths. The permeability coefficient k of GMZ Ca-bentonite at dry density Pd of 1.75 g/cm 3 can be calculated as 2.0 × 10 -11 cm/s by the linear relationship between Pd and log k. It is closed to the permeability coefficient of GMZ Ca-bentonite with the same dry density published in literature, which testifies that the method calculating the permeability coefficient is feasible from the consolidation coefficient obtained by the consolidation test. (authors)

Analysis of isoclinic fringes of a circular disk under diametric compression

International Nuclear Information System (INIS)

Jung, Girl; Park, Tae Geun; Yang, Min Bok; Kim, Myung Soo; Baek, Tae Hyun

2005-01-01

This paper presents the process for obtaining isoclinic fringes from experiment and compares the experimental results with theoretical calculations. In this experiment, the polaris cope named 'Stress master' is used as a primary tool, combined with a circular disk made of urethane rubber called as 'Photoflex' and a CCD camera to record the isoclinic fringes. In photoelasticity, isoclinics can be used to get the stress trajectories and then to analyze the whole field stresses. But it must be emphasized that isoclinic fringes are not themselves stress trajectories. In this paper, isoclinics are measured accurately by use of sharpening technique. Experimental results are comparable to those of theory.

Pre-event trajectories of mental health and health-related disabilities, and post-event traumatic stress symptoms and health : A 7-wave population-based study

NARCIS (Netherlands)

van der Velden, Peter; Bosmans, Mark; van der Meulen, Erik; Vermunt, J.K.

2016-01-01

It is unknown to what extent classes of trajectories of pre-event mental health problems (MHP) and health-related disabilities (HRD), predict post-event traumatic stress symptoms (PTSS), MHP and HRD. Aim of the present 7-wave study was to assess the predictive values using a representative sample of

Effect of transverse compression on I/sub c/ of Nb3Sn multifilamentary wire

International Nuclear Information System (INIS)

Specking, W.; Goldacker, W.; Fluekiger, R.

1988-01-01

The effect of transverse compressive stress on critical current in bronze processed Nb 3 Sn multifilamentary wires was measured at 13.5 T. For the same wire the critical current was more sensitive to this stress than to axial stress. An increase in this stress first caused a slight enhancement of the critical current followed by a drastic decrease of 50 percent at a stress equal to 100 MPa. X-ray diffraction under transverse compression revealed a decrease in the spacing between the lattice planes parallel to the wire axis. This provided a physical basis for the initial enhancement of the critical current under transverse compressive stress

Stress relaxation in vanadium under shock and shockless dynamic compression

International Nuclear Information System (INIS)

Kanel, G. I.; Razorenov, S. V.; Garkushin, G. V.; Savinykh, A. S.; Zaretsky, E. B.

2015-01-01

Evolutions of elastic-plastic waves have been recorded in three series of plate impact experiments with annealed vanadium samples under conditions of shockless and combined ramp and shock dynamic compression. The shaping of incident wave profiles was realized using intermediate base plates made of different silicate glasses through which the compression waves were entered into the samples. Measurements of the free surface velocity histories revealed an apparent growth of the Hugoniot elastic limit with decreasing average rate of compression. The growth was explained by “freezing” of the elastic precursor decay in the area of interaction of the incident and reflected waves. A set of obtained data show that the current value of the Hugoniot elastic limit and plastic strain rate is rather associated with the rate of the elastic precursor decay than with the local rate of compression. The study has revealed the contributions of dislocation multiplications in elastic waves. It has been shown that independently of the compression history the material arrives at the minimum point between the elastic and plastic waves with the same density of mobile dislocations

Residual Stress State in Single-Edge Notched Tension Specimen Caused by the Local Compression Technique

Directory of Open Access Journals (Sweden)

Huang Yifan

2016-12-01

Full Text Available Three-dimensional (3D finite element analyses (FEA are performed to simulate the local compression (LC technique on the clamped single-edge notched tension (SE(T specimens. The analysis includes three types of indenters, which are single pair of cylinder indenters (SPCI, double pairs of cylinder indenters (DPCI and single pair of ring indenters (SPRI. The distribution of the residual stress in the crack opening direction in the uncracked ligament of the specimen is evaluated. The outcome of this study can facilitate the use of LC technique on SE(T specimens.

The relationship between trajectories of family/cultural stressors and depression and suicidal ideation among substance using Mexican-American adults.

Science.gov (United States)

Saint Onge, Jarron M; Cepeda, Alice; Lee King, Patricia A; Valdez, Avelardo

2013-12-01

We used an intersectional minority stress perspective to examine the association between family/cultural stress and mental health among substance-using Mexican-Americans. Employing a unique longitudinal sample of 239 socioeconomically disadvantaged, non-injecting heroin-using Mexican-Americans from San Antonio, Texas, we examined how culturally relevant stressors are related to depression and suicidal ideation. First, we identified depression and suicidal ideation prevalence rates for this disadvantaged sample. Second, we determined how cultural stress is experienced over time using stress trajectories. Third, we evaluated how family/cultural stressors and stress trajectories are related to depression and suicidal ideation outcomes. Results showed high rates of baseline depression (24 %) and suicidal ideation (30 %). We used latent class growth analysis to identify three primary stress trajectories (stable, high but decreasing, and increasing) over three time points during 1 year. We found that the increasing stressors trajectory was associated with higher rates of depression and suicidal ideation, and that stress trajectories had unique relationships with mental illness. We also showed that baseline stressors, sum stressors, and high but decreasing stressors maintained positive associations with mental illness after controlling for baseline depression. Our results highlight the importance of focusing on within-group, culturally specific stressors and addressing both operant and cumulative stressors in the study of mental health for marginalized populations and suggest the importance of early intervention in minimizing stressors.

Academic and Workplace-related Visual Stresses Induce Detectable Deterioration Of Performance, Measured By Basketball Trajectories and Astigmatism Impacting Athletes Or Students In Military Pilot Training.

Science.gov (United States)

Mc Leod, Roger D.

2004-03-01

Separate military establishments across the globe can confirm that a high percentage of their prospective pilots-in-training are no longer visually fit to continue the flight training portion of their programs once their academic coursework is completed. I maintain that the visual stress induced by those intensive protocols can damage the visual feedback mechanism of any healthy and dynamic system beyond its usual and ordinary ability to self-correct minor visual loss of acuity. This deficiency seems to be detectable among collegiate and university athletes by direct observation of the height of the trajectory arc of a basketball's flight. As a particular athlete becomes increasingly stressed by academic constraints requiring long periods of concentrated reading under highly static angular convergence of the eyes, along with unfavorable illumination and viewing conditions, eyesight does deteriorate. I maintain that induced astigmatism is a primary culprit because of the evidence of that basketball's trajectory! See the next papers!

The Diagonal Compression Field Method using Circular Fans

DEFF Research Database (Denmark)

Hansen, Thomas

2005-01-01

This paper presents a new design method, which is a modification of the diagonal compression field method, the modification consisting of the introduction of circular fan stress fields. The traditional method does not allow changes of the concrete compression direction throughout a given beam...... if equilibrium is strictly required. This is conservative, since it is not possible fully to utilize the concrete strength in regions with low shear stresses. The larger inclination (the smaller -value) of the uniaxial concrete stress the more transverse shear reinforcement is needed; hence it would be optimal...... if the -value for a given beam could be set to a low value in regions with high shear stresses and thereafter increased in regions with low shear stresses. Thus the shear reinforcement would be reduced and the concrete strength would be utilized in a better way. In the paper it is shown how circular fan stress...

Compressive Failure of Fibre Reinforced Materials

DEFF Research Database (Denmark)

Jensen, Henrik Myhre

2003-01-01

Compressive failure of uni-directional fibre composites by the kink band mechanism is analysed taking into account effects of residual stresses. Two criteria for determining the strength of the composite material have been investigated: Kink band formation at a bifurcation stress in a composite...... with perfectly aligned fibres, and kink band formation at a peak stress in a composite with a band of imperfect material....

Measurement of the through thickness compression of a battery separator

Science.gov (United States)

Yan, Shutian; Huang, Xiaosong; Xiao, Xinran

2018-04-01

The mechanical integrity of the separator is critical to the reliable operation of a battery. Due to its minimal thickness, compression experiments with a single/a few layers of separator are difficult to perform. In this work, a capacitance based displacement set-up has been developed for the measurement of the through thickness direction (TTD) compression stress-strain behavior of the separator and the investigation of its interaction with the electrode. The experiments were performed for a stack of two layers of Celgard 2400 separator, NMC cathode, and separator/NMC cathode/separator stack in both dry and wet (i.e. submersed in dimethyl carbonate DMC) conditions. The experimental results reveal that the separator compression modulus can be significantly affected by the presence of DMC. The iso-stress based rule of mixtures was used to compute the compressive stress-strain curve for the stack from that of the separator and NMC layer. The computed curve agreed with the experimental curve reasonably well up to about 0.16 strain but deviated significantly to a softer response at higher strains. The results suggest that, in the stack, the TTD compressive deformation of the separator is influenced by the NMC cathode.

3D characterization of coal strains induced by compression, carbon dioxide sorption, and desorption at in-situ stress conditions

International Nuclear Information System (INIS)

Pone, J. Denis N.; Halleck, Phillip M.; Mathews, Jonathan P.

2010-01-01

Sequestration of carbon dioxide in unmineable coal seams is an option to combat climate change and an opportunity to enhance coalbed methane production. Prediction of sequestration potential in coal requires characterization of porosity, permeability, sorption capacity and the magnitude of swelling due to carbon dioxide uptake or shrinkage due to methane and water loss. Unfortunately, the majority of data characterizing coal-gas systems have been obtained from powdered, unconfined coal samples. Little is known about confined coal behavior during carbon dioxide uptake and methane desorption. The present work focuses on the characterization of lithotype specific deformation, and strain behavior during CO 2 uptake at simulated in-situ stress conditions. It includes the evaluation of three-dimensional strain induced by the confining stress, the sorption, and the desorption of carbon dioxide. X-ray computed tomography allowed three-dimensional characterization of the bituminous coal deformation samples under hydrostatic stress. The application of 6.9 MPa of confining stress contributes an average of - 0.34% volumetric strain. Normal strains due to confining stress were - 0.08%, - 0.15% and - 0.11% along the x, y and z axes respectively. Gas injection pressure was 3.1 MPa and the excess sorption was 0.85 mmol/g. Confined coal exposed to CO 2 for 26 days displays an average volumetric expansion of 0.4%. Normal strains due to CO 2 sorption were 0.11%, 0.22% and 0.11% along x, y and z axes. Drainage of the CO 2 induced an average of - 0.33% volumetric shrinkage. Normal strains due to CO 2 desorption were - 0.23%, - 0.08% and - 0.02% along x, y and z axes. Alternating positive and negative strain values observed along the sample length during compression, sorption and desorption respectively emphasized that both localized compression/compaction and expansion of coal will occur during CO 2 sequestration. (author)

Effect of Applied Stress and Temperature on Residual Stresses Induced by Peening Surface Treatments in Alloy 600

Science.gov (United States)

Telang, A.; Gnäupel-Herold, T.; Gill, A.; Vasudevan, V. K.

2018-04-01

In this study, the effects of applied tensile stress and temperature on laser shock peening (LSP) and cavitation shotless peening (CSP)-induced compressive residual stresses were investigated using neutron and x-ray diffraction. Residual stresses on the surface, measured in situ, were lower than the applied stress in LSP- and CSP-treated Alloy 600 samples (2 mm thick). The residual stress averaged over the volume was similar to the applied stress. Compressive residual stresses on the surface and balancing tensile stresses in the interior relax differently due to hardening induced by LSP. Ex situ residual stress measurements, using XRD, show that residual stresses relaxed as the applied stress exceeded the yield strength of the LSP- and CSP-treated Alloy 600. Compressive residual stresses induced by CSP and LSP decreased by 15-25% in magnitude, respectively, on exposure to 250-450 °C for more than 500 h with 10-11% of relaxation occurring in the first few hours. Further, 80% of the compressive residual stresses induced by LSP and CSP treatments in Alloy 600 were retained even after long-term aging at 350 °C for 2400 h.

Analysis of compressive fracture in rock using statistical techniques

Energy Technology Data Exchange (ETDEWEB)

Blair, S.C.

1994-12-01

Fracture of rock in compression is analyzed using a field-theory model, and the processes of crack coalescence and fracture formation and the effect of grain-scale heterogeneities on macroscopic behavior of rock are studied. The model is based on observations of fracture in laboratory compression tests, and incorporates assumptions developed using fracture mechanics analysis of rock fracture. The model represents grains as discrete sites, and uses superposition of continuum and crack-interaction stresses to create cracks at these sites. The sites are also used to introduce local heterogeneity. Clusters of cracked sites can be analyzed using percolation theory. Stress-strain curves for simulated uniaxial tests were analyzed by studying the location of cracked sites, and partitioning of strain energy for selected intervals. Results show that the model implicitly predicts both development of shear-type fracture surfaces and a strength-vs-size relation that are similar to those observed for real rocks. Results of a parameter-sensitivity analysis indicate that heterogeneity in the local stresses, attributed to the shape and loading of individual grains, has a first-order effect on strength, and that increasing local stress heterogeneity lowers compressive strength following an inverse power law. Peak strength decreased with increasing lattice size and decreasing mean site strength, and was independent of site-strength distribution. A model for rock fracture based on a nearest-neighbor algorithm for stress redistribution is also presented and used to simulate laboratory compression tests, with promising results.

Elastic-plastic behaviour of thick-walled containers considering plastic compressibility

International Nuclear Information System (INIS)

Betten, J.; Frosch, H.G.

1983-01-01

In this paper the elastic-plastic behaviour of thick-walled pressure vessels with internal and external pressure is studied. To describe the mechanical behaviour of isotropic, plastic compressible materials we use a plastic potential which is a single-valued function of the principle stresses. For cylinders and spheres an analytic expression for the computation of stresses and residual stresses is specified. Afterwards the strains are calculated by using the finite difference method. Some examples will high-light the influence of the plastic compressibility on the behaviour of pressure vessels. (orig.) [de

Isentropic compression with the SPHINX machine

International Nuclear Information System (INIS)

D'almeida, T; Lasalle, F.; Morell, A.; Grunenwald, J.; Zucchini, F.; Loyen, A.

2013-01-01

The SPHINX machine is a generator of pulsed high power (Class 6 MA, 1 μs) that can be used in the framework of inertial fusion for achieving isentropic compression experiments. The magnetic field created by the current impulse generates a quasi-isentropic compression of a metallic liner. In order to optimize this mode of operation, the current impulse is shaped through a device called DLCM (Dynamic Load Current Multiplier). The DLCM device allows both the increase of the amplitude of the current injected into the liner and its shaping. Some preliminary results concerning an aluminium liner are reported. The measurement of the speed of the internal surface of the liner during its implosion and over a quite long trajectory has been possible by interferometry and the results agree well with simulations based on the experimental value of the current delivered to the liner

The thermoviscoplastic response of polycrystalline tungsten in compression

International Nuclear Information System (INIS)

Lennon, A.M.; Ramesh, K.T.

2000-01-01

The thermomechanical response of commercially pure polycrystalline tungsten was investigated over a wide range of strain rates and temperatures. The material was examined in two forms: one an equiaxed recrystallized microstructure and the other a heavily deformed extruded microstructure that was loaded in compression along the extrusion axis. Low strain rate (10 -3 -10 0 s -1 ) compression experiments were conducted on an MTS servo-hydraulic load frame equipped with an infra-red furnace capable of sustaining specimen temperatures in excess of 600 C. High strain rate (10 3 -10 4 s -1 ) experiments were performed on a compression Kolsky bar equipped with an infra-red heating system capable of developing specimen temperatures as high as 800 C. Pressure-shear plate impact experiments were used to obtain shear stress versus shear strain curves at very high rates (∝10 4 -10 5 s -1 ). The recrystallized material was able to sustain very substantial plastic deformations in compression (at room temperature), with a flow stress that appears to be rate-dependent. Intergranular microcracks were developed during the compressive deformations. Under quasi-static loadings a few relatively large axial splitting cracks were formed, while under dynamic loadings a very large number of small, uniformly distributed microcracks (that did not link up to form macrocracks) were developed. The rate of nucleation of microcracks increased dramatically with strain rate. The extruded tungsten is also able to sustain large plastic deformations in compression, with a flow stress that increases with the rate of deformation. The strain hardening of the extruded material is lower than that of the recrystallized material, and is relatively insensitive to the strain rate. (orig.)

Mental health trajectories and their embeddedness in work and family circumstances: a latent state-trait approach to life-course trajectories.

Science.gov (United States)

Cullati, Stéphane; Courvoisier, Delphine S; Burton-Jeangros, Claudine

2014-09-01

Mental health trajectories are known to be influenced by work and family circumstances. However, few studies have examined both of these influences simultaneously in a longitudinal manner. The life-course perspective stresses the importance of examining trajectories in terms of both stable and dynamic components. In this article we use structural equation models (latent state-trait, LST) to distinguish the stable and situational components of mental health trajectories and hypothesise that situational mental health is influenced by satisfaction with work and family, and this effect differs by gender. An analysis of data from a nationally representative sample of 1616 working Swiss residents (2000-2006) shows that mental health trajectories are mostly stable and only slightly sensitive to situational influences. However, situational influences in a given wave do predict situational influences in the next wave. Satisfaction with work and family influences situational mental health in both genders, but the impact is greater for men. In conclusion, the LST approach allows for the examination of mental health trajectories from a life-course perspective by distinguishing stable and situational components. Mental health trajectories are more stable and constant than they are dependent on work and family circumstances, and men are more sensitive to family circumstances than women. © 2014 The Authors. Sociology of Health & Illness © 2014 Foundation for the Sociology of Health & Illness/John Wiley & Sons.

Posttraumatic Stress Symptoms and Trajectories in Child Sexual Abuse Victims: An Analysis of Sex Differences Using the National Survey of Child and Adolescent Well-Being

Science.gov (United States)

Maikovich, Andrea Kohn; Koenen, Karestan C.; Jaffee, Sara R.

2009-01-01

Very few studies have prospectively examined sex differences in posttraumatic stress symptoms and symptom trajectories in youth victimized by childhood sexual abuse. This study addresses that question in a relatively large sample of children, drawn from the National Survey of Child and Adolescent Well-Being, who were between the ages of 8-16 years…

Preliminary Investigation of Workplace-Provided Compressed Mindfulness-Based Stress Reduction with Pediatric Medical Social Workers.

Science.gov (United States)

Trowbridge, Kelly; Mische Lawson, Lisa; Andrews, Stephanie; Pecora, Jodi; Boyd, Sabra

2017-11-01

Mindfulness practices, including mindfulness meditation, show promise for decreasing stress among health care providers. This exploratory study investigates the feasibility of a two-day compressed mindfulness-based stress reduction (cMBSR) course provided in the hospital workplace with pediatric health care social workers. The standard course of Jon Kabat-Zinn's MBSR requires a participant commitment to eight weeks of instruction consisting of one 2.5-hour-per-week class, a single day retreat, and 45 minutes of practice for six of seven days each week. Commitments to family, work, caregiving, education, and so on, as well as limitations such as distance, may prevent health care providers from participating in a standard MBSR course. Using t tests, researchers measured the effect of cMBSR on (a) positive and negative experiences in pediatric social work, (b) perceived stress, (c) mindfulness, and (d) caring self-efficacy (as a component of patient- and family-centered care). Results included significant differences between the pre- and post-intervention outcome variables on the Professional Quality of Life Secondary Traumatic Stress subscale, the Mindful Attention and Awareness Scale, and the Caring Efficacy Scale. Findings found adequate evidence for the feasibility of cMBSR design and for a need of a more rigorous study of the effects of the cMBSR intervention. © 2017 National Association of Social Workers.

Compressive strength of brick masonry made with weak mortars

DEFF Research Database (Denmark)

Pedersen, Erik Steen; Hansen, Klavs Feilberg

2013-01-01

in the joint will ensure a certain level of load-carrying capacity. This is due to the interaction between compression in the weak mortar and tension in the adjacent bricks. This paper proposes an expression for the compressive strength of masonry made with weak lime mortars (fm... of masonry depends only on the strength of the bricks. A compression failure in masonry made with weak mortars occurs as a tension failure in the bricks, as they seek to prevent the mortar from being pressed out of the joints. The expression is derived by assuming hydrostatic pressure in the mortar joints......, which is the most unfavourable stress distribution with respect to tensile stresses in bricks. The expression is compared with the results of compression tests of masonry made with weak mortars. It can take into account bricks with arbitrary dimensions as well as perforated bricks. For a stronger mortar...

Evaluation of shear-compressive strength properties for laminated GFRP composites in electromagnet system

Science.gov (United States)

Song, Jun Hee; Kim, Hak Kun; Kim, Sam Yeon

2014-07-01

Laminated fiber-reinforced composites can be applied to an insulating structure of a nuclear fusion device. It is necessary to investigate the interlaminar fracture characteristics of the laminated composites for the assurance of design and structural integrity. The three methods used to prepare the glass fiber reinforced plastic composites tested in this study were vacuum pressure impregnation, high pressure laminate (HPL), and prepreg laminate. We discuss the design criteria for safe application of composites and the shear-compressive test methods for evaluating mechanical properties of the material. Shear-compressive tests could be performed successfully using series-type test jigs that were inclined 0°, 30°, 45°, 60°, and 75° to the normal axis. Shear strength depends strongly on the applied compressive stress. The design range of allowable shear stress was extended by use of the appropriate composite fabrication method. HPL had the largest design range, and the allowable interlaminar shear stress was 0.254 times the compressive stress.

Atomistic simulation of rapid compression of fractured silicon carbide

International Nuclear Information System (INIS)

Romano, A.; Li, J.; Yip, S.

2006-01-01

Deformation mechanisms of a crack in silicon carbide under high-rate compression are investigated by molecular dynamics simulation. The penny-shaped crack is in tension throughout the simulation while a variable compression is applied in an in-plane direction. Two different mechanisms of crack-tip response are observed: (1) At low tension, a disordered band forms from the crack surface in the direction orthogonal to the compression, which grows as the compressional force is increased in a manner suggesting a stress-induced transition from an ordered to a disordered phase. Moreover the crack is observed to close. (2) At a tension sufficient to allow the crack to remain open, the compressional stress induces formation of disordered regions along the boundaries of the opened crack, which grow and merge into a band as the compression proceeds. This process is driven by bending of the initial crack, which transforms into a curved slit. This mechanism induces incorporation of fragments of perfect crystal into the disordered band. Similar mechanisms have been experimentally observed to occur in porous SiC under high-strain rate compression

Strain Rate Dependence of Compressive Yield and Relaxation in DGEBA Epoxies

Science.gov (United States)

Arechederra, Gabriel K.; Reprogle, Riley C.; Clarkson, Caitlyn M.; McCoy, John D.; Kropka, Jamie M.; Long, Kevin N.; Chambers, Robert S.

2015-03-01

The mechanical response in uniaxial compression of two diglycidyl ether of bisphenol-A epoxies were studied. These were 828DEA (Epon 828 cured with diethanolamine (DEA)) and 828T403 (Epon 828 cured with Jeffamine T-403). Two types of uniaxial compression tests were performed: A) constant strain rate compression and B) constant strain rate compression followed by a constant strain relaxation. The peak (yield) stress was analyzed as a function of strain rate from Eyring theory for activation volume. Runs at different temperatures permitted the construction of a mastercurve, and the resulting shift factors resulted in an activation energy. Strain and hold tests were performed for a low strain rate where a peak stress was lacking and for a higher strain rate where the peak stress was apparent. Relaxation from strains at different places along the stress-strain curve was tracked and compared. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Allometric trajectories and "stress": a quantitative approach

Directory of Open Access Journals (Sweden)

Tommaso Anfodillo

2016-11-01

Full Text Available The term stress is an important but vague term in plant biology. We show situations in which thinking in terms of stress is profitably replaced by quantifying distance from functionally optimal scaling relationships between plant parts. These relationships include, for example, the often-cited one between leaf area and sapwood area, which presumably reflects mutual dependence between source and sink tissues and which scales positively within individuals and across species. These relationships seem to be so basic to plant functioning that they are favored by selection across nearly all plant lineages. Within a species or population, individuals that are far from the common scaling patterns are thus expected to perform negatively. For instance, too little leaf area (e.g. due to herbivory or disease per unit of active stem mass would be expected to incur to low carbon income per respiratory cost and thus lead to lower growth. We present a framework that allows quantitative study of phenomena traditionally assigned to stress, without need for recourse to this term. Our approach contrasts with traditional approaches for studying stress, e.g. revealing that small stressed plants likely are in fact well suited to local conditions. We thus offer a quantitative perspective to the study of phenomena often referred to under such terms as stress, plasticity, adaptation, and acclimation.

Allometric Trajectories and "Stress": A Quantitative Approach.

Science.gov (United States)

Anfodillo, Tommaso; Petit, Giai; Sterck, Frank; Lechthaler, Silvia; Olson, Mark E

2016-01-01

The term "stress" is an important but vague term in plant biology. We show situations in which thinking in terms of "stress" is profitably replaced by quantifying distance from functionally optimal scaling relationships between plant parts. These relationships include, for example, the often-cited one between leaf area and sapwood area, which presumably reflects mutual dependence between sources and sink tissues and which scales positively within individuals and across species. These relationships seem to be so basic to plant functioning that they are favored by selection across nearly all plant lineages. Within a species or population, individuals that are far from the common scaling patterns are thus expected to perform negatively. For instance, "too little" leaf area (e.g., due to herbivory or disease) per unit of active stem mass would be expected to incur to low carbon income per respiratory cost and thus lead to lower growth. We present a framework that allows quantitative study of phenomena traditionally assigned to "stress," without need for recourse to this term. Our approach contrasts with traditional approaches for studying "stress," e.g., revealing that small "stressed" plants likely are in fact well suited to local conditions. We thus offer a quantitative perspective to the study of phenomena often referred to under such terms as "stress," plasticity, adaptation, and acclimation.

Effect of compressive stress on stability of N-doped p-type ZnO

International Nuclear Information System (INIS)

Chen Xingyou; Zhang Zhenzhong; Jiang Mingming; Wang Shuangpeng; Li Binghui; Shan Chongxin; Liu Lei; Zhao Dongxu; Shen Dezhen; Yao Bin

2011-01-01

Nitrogen-doped p-type zinc oxide (p-ZnO:N) thin films were fabricated on a-/c-plane sapphire (a-/c-Al 2 O 3 ) by plasma-assisted molecular beam epitaxy. Hall-effect measurements show that the p-type ZnO:N on c-Al 2 O 3 degenerated into n-type after a preservation time; however, the one grown on a-Al 2 O 3 showed good stability. The conversion of conductivity in the one grown on c-Al 2 O 3 ascribed to the faster disappearance of N O and the growing N 2(O) , which is demonstrated by x-ray photoelectron spectroscopy (XPS). Compressive stress, caused by lattice misfit, was revealed by Raman spectra and optical absorption spectra, and it was regarded as the root of the instability in ZnO:N.

On the characterisation of the dynamic compressive behaviour of silicon carbides subjected to isentropic compression experiments

Directory of Open Access Journals (Sweden)

Zinszner Jean-Luc

2015-01-01

Full Text Available Ceramic materials are commonly used as protective materials particularly due to their very high hardness and compressive strength. However, the microstructure of a ceramic has a great influence on its compressive strength and on its ballistic efficiency. To study the influence of microstructural parameters on the dynamic compressive behaviour of silicon carbides, isentropic compression experiments have been performed on two silicon carbide grades using a high pulsed power generator called GEPI. Contrary to plate impact experiments, the use of the GEPI device and of the lagrangian analysis allows determining the whole loading path. The two SiC grades studied present different Hugoniot elastic limit (HEL due to their different microstructures. For these materials, the experimental technique allowed evaluating the evolution of the equivalent stress during the dynamic compression. It has been observed that these two grades present a work hardening more or less pronounced after the HEL. The densification of the material seems to have more influence on the HEL than the grain size.

Compressive strength evolution of thermally-stressed Saint Maximin limestone.

Science.gov (United States)

Farquharson, J.; Griffiths, L.; Baud, P.; Wadsworth, F. B.; Heap, M. J.

2017-12-01

The Saint Maximin quarry (Oise, France) opened in the early 1600s, and its limestone has been used extensively as masonry stone, particularly during the classical era of Parisian architecture from the 17th century onwards. Its widespread use has been due to a combination of its regional availability, its high workability, and its aesthetic appeal. Notable buildings completed using this material include sections of the Place de la Concorde and the Louvre in Paris. More recently, however, it has seen increasing use in the construction of large private residences throughout the United States as well as extensions to private institutions such as Stanford University. For any large building, fire hazard can be a substantial concern, especially in tectonically active areas where catastrophic fires may arise following large-magnitude earthquakes. Typically, house fires burn at temperatures of around 600 °C ( 1000 F). Given the ubiquity of this geomaterial as a building stone, it is important to ascertain the influence of heating on the strength of Saint Maximin limestone (SML), and in turn the structural stability of the buildings it is used in. We performed a series of compressive tests and permeability measurements on samples of SML to determine its strength evolution in response to heating to incrementally higher temperatures. We observe that the uniaxial compressive strength of SML decreases from >12 MPa at room temperature to 400 °C). We anticipate that this substantial weakening is in part a result of thermal microcracking, whereby changes in temperature induce thermal stresses due to a mismatch in thermal expansion between the constituent grains. This mechanism is compounded by the volumetric increase of quartz through its alpha - beta transition at 573 °C, and by the thermal decomposition of calcite. To track the formation of thermal microcracks, we monitor acoustic emissions, a common proxy for microcracking, during the heating of an SML sample. The

Influence of applied compressive stress on the hysteresis curves and magnetic domain structure of grain-oriented transverse Fe–3%Si steel

Czech Academy of Sciences Publication Activity Database

Perevertov, Oleksiy; Schäfer, R.

2012-01-01

Roč. 45, č. 13 (2012), "135001-1"-"135001-11" ISSN 0022-3727 Grant - others:GA AV ČR(CZ) M100100906 Institutional research plan: CEZ:AV0Z10100520 Keywords : hysteresis curve * magnetic domains * compressive stress * goss steel * effective field Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.528, year: 2012

Time-resolved shock compression of porous rutile: Wave dispersion in porous solids

Energy Technology Data Exchange (ETDEWEB)

Anderson, M.U.; Graham, R.A.; Holman, G.T.

1993-08-01

Rutile (TiO{sub 2}) samples at 60% of solid density have been shock-loaded from 0.21 to 6.1 GPa with sample thickness of 4 mm and studied with the PVDF piezoelectric polymer stress-rate gauge. The technique uses a copper capsule to contain the sample which has PVDF gauge packages in direct contact with front and rear surfaces. A precise measure is made of the compressive stress wave velocity through the sample, as well as the input and propagated shock stress. Initial density is known from sample preparation, and the amount of shock-compression is calculated from the measurement of shock velocity and input stress. Shock states and re-shock states are measured. Observed data are consistent with previously published high pressure data. It is observed that rutile has a ``crush strength`` near 6 GPa. Propagated stress-pulse rise times vary from 234 to 916 nsec. Propagated stress-pulse rise times of shock-compressed HMX, 2Al + Fe{sub 2}O{sub 3}, 3Ni + Al, and 5Ti + 3Si are presented.

Behavior of porous tungsten under shock compression at room temperature

International Nuclear Information System (INIS)

Dandekar, D.P.; Lamothe, R.M.

1977-01-01

This work reports the results of room-temperature shock-compression experiments on porous tungsten. The porous tungsten was fabricated by sintering 1-μm tungsten particles. The initial density of the material was 15290 kg/m 3 . Around 97% of the pores in the material were interconnected. The main features of the results are as follows: (1) porous tungsten behaves as a linear elastic material to 1.43 GPa; (2) the shock wave following the elastic precursor is unstable in the material in the stress range 1.43--2.7 GPa; (3) a stable two-wave structure is established at and above 6.4 GPa; (4) the response of porous tungsten is accurately described by the Mie-Grueneisen equation of state at stresses above 4.9 GPa, the stress at which the voids suffer a complete extinction in the material; (5) the deformations induced in the material due to shock compression are irreversible; (6) the recentered Hugoniot of porous tungsten becomes stiffer with the increasing magnitude of initial compressive stress

Compressibility of 304 Stainless Steel Powder Metallurgy Materials Reinforced with 304 Short Stainless Steel Fibers.

Science.gov (United States)

Yao, Bibo; Zhou, Zhaoyao; Duan, Liuyang; Xiao, Zhiyu

2016-03-04

Powder metallurgy (P/M) technique is usually used for manufacturing porous metal materials. However, some P/M materials are limitedly used in engineering for their performance deficiency. A novel 304 stainless steel P/M material was produced by a solid-state sintering of 304 stainless steel powders and 304 short stainless steel fibers, which were alternately laid in layers according to mass ratio. In this paper, the compressive properties of the P/M materials were characterized by a series of uniaxial compression tests. The effects of fiber content, compaction pressure and high temperature nitriding on compressive properties were investigated. The results indicated that, without nitriding, the samples changed from cuboid to cydariform without damage in the process of compression. The compressive stress was enhanced with increasing fiber content ranging from 0 to 8 wt.%. For compaction pressure from 55 to 75 MPa, greater compaction pressure improved compressive stress. Moreover, high temperature nitriding was able to significantly improve the yield stress, but collapse failure eventually occurred.

Accurately tracking single-cell movement trajectories in microfluidic cell sorting devices.

Science.gov (United States)

Jeong, Jenny; Frohberg, Nicholas J; Zhou, Enlu; Sulchek, Todd; Qiu, Peng

2018-01-01

Microfluidics are routinely used to study cellular properties, including the efficient quantification of single-cell biomechanics and label-free cell sorting based on the biomechanical properties, such as elasticity, viscosity, stiffness, and adhesion. Both quantification and sorting applications require optimal design of the microfluidic devices and mathematical modeling of the interactions between cells, fluid, and the channel of the device. As a first step toward building such a mathematical model, we collected video recordings of cells moving through a ridged microfluidic channel designed to compress and redirect cells according to cell biomechanics. We developed an efficient algorithm that automatically and accurately tracked the cell trajectories in the recordings. We tested the algorithm on recordings of cells with different stiffness, and showed the correlation between cell stiffness and the tracked trajectories. Moreover, the tracking algorithm successfully picked up subtle differences of cell motion when passing through consecutive ridges. The algorithm for accurately tracking cell trajectories paves the way for future efforts of modeling the flow, forces, and dynamics of cell properties in microfluidics applications.

Accurately tracking single-cell movement trajectories in microfluidic cell sorting devices.

Directory of Open Access Journals (Sweden)

Jenny Jeong

Full Text Available Microfluidics are routinely used to study cellular properties, including the efficient quantification of single-cell biomechanics and label-free cell sorting based on the biomechanical properties, such as elasticity, viscosity, stiffness, and adhesion. Both quantification and sorting applications require optimal design of the microfluidic devices and mathematical modeling of the interactions between cells, fluid, and the channel of the device. As a first step toward building such a mathematical model, we collected video recordings of cells moving through a ridged microfluidic channel designed to compress and redirect cells according to cell biomechanics. We developed an efficient algorithm that automatically and accurately tracked the cell trajectories in the recordings. We tested the algorithm on recordings of cells with different stiffness, and showed the correlation between cell stiffness and the tracked trajectories. Moreover, the tracking algorithm successfully picked up subtle differences of cell motion when passing through consecutive ridges. The algorithm for accurately tracking cell trajectories paves the way for future efforts of modeling the flow, forces, and dynamics of cell properties in microfluidics applications.

Developmental trajectories of brain maturation and behavior: Relevance to major mental illnesses

Directory of Open Access Journals (Sweden)

Sedona Lockhart

2018-05-01

Full Text Available Adverse events in childhood and adolescence, such as social neglect or drug abuse, are known to lead to behavioral changes in young adulthood. This is particularly true for the subset of people who are intrinsically more vulnerable to stressful conditions. Yet the underlying mechanisms for such developmental trajectory from early life insult to aberrant adult behavior remains elusive. Adolescence is a period of dynamic physiological, psychological, and behavioral changes, encompassing a distinct neurodevelopmental stage called the ‘critical period’. During adolescence, the brain is uniquely susceptible to stress. Stress mediators may lead to disturbances to biological processes that can cause permanent alterations in the adult stage, even as severe as the onset of mental illness when paired with genetic risk and environmental factors. Understanding the molecular factors governing the critical period and how stress can disturb the maturation processes will allow for better treatment and prevention of late adolescent/young adult onset psychiatric disorders. Keywords: Adolescence, Critical period, Developmental trajectory, Brain maturation, Adult behavior

Magnetic compression into Brillouin flow

International Nuclear Information System (INIS)

Becker, R.

1977-01-01

The trajectories of beam edge electrons are calculated in the transition region between an electrostatic gun and an increasing magnetic field for various field shapes, transition length, and cathode fluxes, assuming that the resultant beam is of Brillouin flow type. The results give a good physical interpretation to the axial gradient of the magnetic field being responsible for the amount of magnetic compression and also for the proper injection conditions. Therefore it becomes possible to predict from the known characteristics of any fairly laminary electrostatic gun the necessary axial gradient of the magnetic field and the axial position of the gun with respect to the field build-up. (orig.) [de

Quasi-static and ratcheting properties of trabecular bone under uniaxial and cyclic compression.

Science.gov (United States)

Gao, Li-Lan; Wei, Chao-Lei; Zhang, Chun-Qiu; Gao, Hong; Yang, Nan; Dong, Li-Min

2017-08-01

The quasi-static and ratcheting properties of trabecular bone were investigated by experiments and theoretical predictions. The creep tests with different stress levels were completed and it is found that both the creep strain and creep compliance increase rapidly at first and then increase slowly as the creep time goes by. With increase of compressive stress the creep strain increases and the creep compliance decreases. The uniaxial compressive tests show that the applied stress rate makes remarkable influence on the compressive behaviors of trabecular bone. The Young's modulus of trabecular bone increases with increase of stress rate. The stress-strain hysteresis loops of trabecular bone under cyclic load change from sparse to dense with increase of number of cycles, which agrees with the change trend of ratcheting strain. The ratcheting strain rate rapidly decreases at first, and then exhibits a relatively stable and small value after 50cycles. Both the ratcheting strain and ratcheting strain rate increase with increase of stress amplitude or with decrease of stress rate. The creep model and the nonlinear viscoelastic constitutive model of trabecular bone were proposed and used to predict its creep property and rate-dependent compressive property. The results show that there are good agreements between the experimental data and predictions. Copyright © 2017 Elsevier B.V. All rights reserved.

Research on the compressive strength of a passenger vehicle roof

Science.gov (United States)

Zhao, Guanglei; Cao, Jianxiao; Liu, Tao; Yang, Na; Zhao, Hongguang

2017-05-01

To study the compressive strength of a passenger vehicle roof, this paper makes the simulation test on the static collapse of the passenger vehicle roof and analyzes the stress and deformation of the vehicle roof under pressure in accordance with the Roof Crush Resistance of Passenger Cars (GB26134-2010). It studies the optimization on the major stressed parts, pillar A, pillar B and the rail of roof, during the static collapse process of passenger vehicle roof. The result shows that the thickness of pillar A and the roof rail has significant influence on the compressive strength of the roof while that of pillar B has minor influence on the compressive strength of the roof.

3D characterization of coal strains induced by compression, carbon dioxide sorption, and desorption at in-situ stress conditions

Energy Technology Data Exchange (ETDEWEB)

Pone, J. Denis N.; Halleck, Phillip M.; Mathews, Jonathan P. [Department of Energy and Mineral Engineering and The EMS Energy Institute, The Pennsylvania State University, University Park, PA 16802 (United States)

2010-06-01

Sequestration of carbon dioxide in unmineable coal seams is an option to combat climate change and an opportunity to enhance coalbed methane production. Prediction of sequestration potential in coal requires characterization of porosity, permeability, sorption capacity and the magnitude of swelling due to carbon dioxide uptake or shrinkage due to methane and water loss. Unfortunately, the majority of data characterizing coal-gas systems have been obtained from powdered, unconfined coal samples. Little is known about confined coal behavior during carbon dioxide uptake and methane desorption. The present work focuses on the characterization of lithotype specific deformation, and strain behavior during CO{sub 2} uptake at simulated in-situ stress conditions. It includes the evaluation of three-dimensional strain induced by the confining stress, the sorption, and the desorption of carbon dioxide. X-ray computed tomography allowed three-dimensional characterization of the bituminous coal deformation samples under hydrostatic stress. The application of 6.9 MPa of confining stress contributes an average of - 0.34% volumetric strain. Normal strains due to confining stress were - 0.08%, - 0.15% and - 0.11% along the x, y and z axes respectively. Gas injection pressure was 3.1 MPa and the excess sorption was 0.85 mmol/g. Confined coal exposed to CO{sub 2} for 26 days displays an average volumetric expansion of 0.4%. Normal strains due to CO{sub 2} sorption were 0.11%, 0.22% and 0.11% along x, y and z axes. Drainage of the CO{sub 2} induced an average of - 0.33% volumetric shrinkage. Normal strains due to CO{sub 2} desorption were - 0.23%, - 0.08% and - 0.02% along x, y and z axes. Alternating positive and negative strain values observed along the sample length during compression, sorption and desorption respectively emphasized that both localized compression/compaction and expansion of coal will occur during CO{sub 2} sequestration. (author)

Compressive buckling of black phosphorene nanotubes: an atomistic study

Science.gov (United States)

Nguyen, Van-Trang; Le, Minh-Quy

2018-04-01

We investigate through molecular dynamics finite element method with Stillinger-Weber potential the uniaxial compression of armchair and zigzag black phosphorene nanotubes. We focus especially on the effects of the tube’s diameter with fixed length-diameter ratio, effects of the tube’s length for a pair of armchair and zigzag tubes of equal diameters, and effects of the tube’s diameter with fixed lengths. Their Young’s modulus, critical compressive stress and critical compressive strain are studied and discussed for these 3 case studies. Compressive buckling was clearly observed in the armchair nanotubes. Local bond breaking near the boundary occurred in the zigzag ones under compression.

Cyclic compressive creep-elastoplastic behaviors of in situ TiB_2/Al-reinforced composite

International Nuclear Information System (INIS)

Zhang, Qing; Zhang, Weizheng; Liu, Youyi; Guo, BingBin

2016-01-01

This paper presents a study on the cyclic compressive creep-elastoplastic behaviors of a TiB_2-reinforced aluminum matrix composite (ZL109) at 350 °C and 200 °C. According to the experimental results, under cyclic elastoplasticity and cyclic coupled compressive creep-elastoplasticity, the coupled creep will cause changes in isotropic stress and kinematic stress. Isotropic stress decreases with coupled creep, leading to cyclic softening. Positive kinematic stress, however, increases with coupled creep, leading to cyclic hardening. Transmission electron microscopy (TEM) observations of samples under cyclic compressive creep-elastoplasticity with different temperatures and strain amplitudes indicate that more coupled creep contributes to more subgrain boundaries but fewer intracrystalline dislocations. Based on the macro tests and micro observations, the micro mechanism of compressive creep's influence on cyclic elastoplasticity is elucidated. Dislocations recovering with coupled creep leads to isotropic softening, whereas subgrain structures created by coupled creep lead to kinematic hardening during cyclic deformation.

An experimental study on the effects of compressive stress on the fatigue crack growth of low-alloy steel

International Nuclear Information System (INIS)

Jones, D.P.; Hoppe, R.G.; James, B.A.

1993-01-01

A series of fatigue crack growth rate tests was conducted in order to study effects of negative stress ratio on fatigue crack growth rate of low-alloy steel in air. Four-point bend specimens were used to simulate linear stress distributions typical of pressure vessel applications. This type of testing adds to knowledge on negative stress ratio effects for low-alloy steels obtained in the past from uniform tension-compression tests. Applied bending stress range was varied over twice the yield strength. Load control was used for tests for which the stress range was less than twice the yield strength and deflection control was used for the higher stress range tests. Crack geometries were both short and long fatigue cracks started at notches and tight fatigue cracks for which crack closure could occur over the full crack face. Results are presented in terms of the stress intensity factor ratio R = K MIN /K MAX . The negative R-ratio test results were correlated to an equation of the form da/dN = C[ΔK/(A-R)] n , where A, C, and n are curve fitting parameters. It was found that effects of negative R-ratio on fatigue crack growth rates for even the high stress range tests could be bounded by correlating the above equation to only positive R-ratio test results and extending the resulting equation into the negative R-ratio regime

Trajectories of Diurnal Cortisol in Mothers of Children with Autism and Other Developmental Disabilities: Relations to Health and Mental Health

Science.gov (United States)

Dykens, Elisabeth M.; Lambert, Warren

2013-01-01

This study used a stress biomarker, diurnal cortisol, to identify how elevated stress in mothers of children and adults with autism and other disabilities relates to their health and mental health. Based on semi-parametric, group-based trajectory analysis of 91 mothers, two distinctive cortisol trajectories emerged: blunted (63%) or steep (37%).…

A Decade of War: Prospective Trajectories of Posttraumatic Stress Disorder Symptoms Among Deployed US Military Personnel and the Influence of Combat Exposure.

Science.gov (United States)

Donoho, Carrie J; Bonanno, George A; Porter, Ben; Kearney, Lauren; Powell, Teresa M

2017-12-15

Posttraumatic stress disorder (PTSD) is a common psychiatric disorder among service members and veterans. The clinical course of PTSD varies between individuals, and patterns of symptom development have yet to be clearly delineated. Previous studies have been limited by convenience sampling, short follow-up periods, and the inability to account for combat-related trauma. To determine the trajectories of PTSD symptoms among deployed military personnel with and without combat exposure, we used data from a population-based representative sample of 8,178 US service members who participated in the Millennium Cohort Study from 2001 to 2011. Using latent growth mixture modeling, trajectories of PTSD symptoms were determined in the total sample, as well as in individuals with and without combat exposure, respectively. Overall, 4 trajectories of PTSD were characterized: resilient, pre-existing, new-onset, and moderate stable. Across all trajectories, combat-deployed service members diverged from non-combat-deployed service members, even after a single deployment. The former also generally had higher PTSD symptoms. Based on the models, nearly 90% of those without combat exposure remained resilient over the 10-year period, compared with 80% of those with combat exposure. Findings demonstrate that although the clinical course of PTSD symptoms shows heterogeneous patterns of development, combat exposure is uniformly associated with poor mental health. Published by Oxford University Press on behalf of the Johns Hopkins Bloomberg School of Public Health 2017. This work is written by (a) US Government employee(s) and is in the public domain in the US.

Stress-assisted crystallisation in anodic titania

International Nuclear Information System (INIS)

Vanhumbeeck, Jean-Francois; Tian He; Schryvers, Dominique; Proost, Joris

2011-01-01

Research highlights: → Correlations between microstructure and internal stress during Ti anodising are established. → Large internal compressive stresses are accumulated in the film during anodising upto 12 V. →A transition from compressive to tensile stress is observed when the cell voltage exceeds 12 V. → At 40 V, the oxide films consist of two regions with different compositions and microstructures. Crystallisation of amorphous to anatase TiO 2 contributes to the compressive stress relaxation. - Abstract: The relationship between the microstructural and internal stress evolution during Ti anodising is discussed. Samples anodised galvanostatically to 12 V and 40 V, corresponding to different stages of the internal stress evolution, were examined by in-plane and cross-section transmission electron microscopy. Electron diffraction patterns have been complemented with stoichiometry data obtained from energy loss near edge structure spectra. The sample anodised to 40 V was observed to consist of two regions, with a crystallised inner region adjacent to the metal/oxide interface. Crystallisation of this region is associated with the presence of large compressive internal stresses which build up during anodising up to 12 V.

Laser-induced generation of pure tensile stresses

International Nuclear Information System (INIS)

Niemz, M.H.; Lin, C.P.; Pitsillides, C.; Cui, J.; Doukas, A.G.; Deutsch, T.F.

1997-01-01

While short compressive stresses can readily be produced by laser ablation, the generation of pure tensile stresses is more difficult. We demonstrate that a 90 degree prism made of polyethylene can serve to produce short and pure tensile stresses. A compressive wave is generated by ablating a thin layer of strongly absorbing ink on one surface of the prism with a Q-switched frequency-doubled Nd:YAG laser. The compressive wave driven into the prism is reflected as a tensile wave by the polyethylene-air interface at its long surface. The low acoustic impedance of polyethylene makes it ideal for coupling tensile stresses into liquids. In water, tensile stresses up to -200bars with a rise time of the order of 20 ns and a duration of 100 ns are achieved. The tensile strength of water is determined for pure tensile stresses lasting for 100 ns only. The technique has potential application in studying the initiation of cavitation in liquids and in comparing the effect of compressive and tensile stress transients on biological media. copyright 1997 American Institute of Physics

Compressibility of 304 Stainless Steel Powder Metallurgy Materials Reinforced with 304 Short Stainless Steel Fibers

Directory of Open Access Journals (Sweden)

Bibo Yao

2016-03-01

Full Text Available Powder metallurgy (P/M technique is usually used for manufacturing porous metal materials. However, some P/M materials are limitedly used in engineering for their performance deficiency. A novel 304 stainless steel P/M material was produced by a solid-state sintering of 304 stainless steel powders and 304 short stainless steel fibers, which were alternately laid in layers according to mass ratio. In this paper, the compressive properties of the P/M materials were characterized by a series of uniaxial compression tests. The effects of fiber content, compaction pressure and high temperature nitriding on compressive properties were investigated. The results indicated that, without nitriding, the samples changed from cuboid to cydariform without damage in the process of compression. The compressive stress was enhanced with increasing fiber content ranging from 0 to 8 wt.%. For compaction pressure from 55 to 75 MPa, greater compaction pressure improved compressive stress. Moreover, high temperature nitriding was able to significantly improve the yield stress, but collapse failure eventually occurred.

Pressure-Induced Changes in Inter-Diffusivity and Compressive Stress in Chemically Strengthened Glass

DEFF Research Database (Denmark)

Svenson, Mouritz Nolsøe; Thirion, Lynn M.; Youngman, Randall E.

chamber to compress bulk glass samples isostatically up to 1 GPa at elevated temperature before or after the ion exchange treatment of an industrial sodium-magnesium aluminosilicate glass. Compression of the samples prior to ion exchange leads to a decreased Na+-K+ inter-diffusivity, increased compressive...

Synthesis of asymmetric movement trajectories in timed rhythmic behaviour by means of frequency modulation.

Science.gov (United States)

Waadeland, Carl Haakon

2017-01-01

Results from different empirical investigations on gestural aspects of timed rhythmic movements indicate that the production of asymmetric movement trajectories is a feature that seems to be a common characteristic of various performances of repetitive rhythmic patterns. The behavioural or neural origin of these asymmetrical trajectories is, however, not identified. In the present study we outline a theoretical model that is capable of producing syntheses of asymmetric movement trajectories documented in empirical investigations by Balasubramaniam et al. (2004). Characteristic qualities of the extension/flexion profiles in the observed asymmetric trajectories are reproduced, and we conduct an experiment similar to Balasubramaniam et al. (2004) to show that the empirically documented movement trajectories and our modelled approximations share the same spectral components. The model is based on an application of frequency modulated movements, and a theoretical interpretation offered by the model is to view paced rhythmic movements as a result of an unpaced movement being "stretched" and "compressed", caused by the presence of a metronome. We discuss our model construction within the framework of event-based and emergent timing, and argue that a change between these timing modes might be reflected by the strength of the modulation in our model. Copyright © 2016 Elsevier B.V. All rights reserved.

Triaxial-compression extraction of pore water from unsaturated tuff, Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Yang, I.C.; Turner, A.K.; Sayre, T.M.; Montazer, P.

1988-01-01

The purpose of this experiment was to design and validate methods for extracting uncontaminated pore water from nonwelded parts of this tuff. Pore water is needed for chemical analysis to help characterize the local hydrologic system. A standard Hoek-Franklin triaxial cell was modified to create a chemically inert pore-water-extraction system. Experimentation was designed to determine the optimum stress and duration of triaxial compression for efficient extraction of uncontaminated pore water. Experimental stress paths consisted of a series of increasing stress levels. Trial axial stress levels ranged from 41 to 190 megapascals with lateral confining stresses of 34 to 69 megapascals. The duration of compression at any given stress level lasted from 10 minutes to 15 hours. A total of 40 experimental extraction trials were made. Tuff samples used in these tests were collected from drill-hole core from the Paintbrush nonwelded unit at Yucca Mountain. Pore water was extracted from tuff samples that had a water content greater than 13 percent by weight. Two stress paths have been determined to be applicable for future pore-water extraction from nonwelded tuff at Yucca Mountain. The initial water content of a sample affects the selection of an appropriate period of compression. 39 refs., 55 figs

Job satisfaction developmental trajectories and health: A life course perspective.

Science.gov (United States)

Dirlam, Jonathan; Zheng, Hui

2017-04-01

Understanding the health consequence of job dissatisfaction becomes increasingly important because job insecurity, stress and dissatisfaction have significantly increased in the United States in the last decade. Despite the extensive work in this area, prior studies nonetheless may underestimate the harmful effect of job dissatisfaction due to the cross-sectional nature of their data and sample selection bias. This study applies a life-course approach to more comprehensively examine the relationship between job satisfaction and health. Using data from the NLSY 1979 cohort, we estimate group based job satisfaction trajectories of respondents starting at age 25 and ending at age 39. Four job satisfaction trajectory groups are identified, a consistently high satisfaction group, a downward group, an upward group, and a lowest satisfaction group. We examine the effects of these trajectories on several physical and mental health outcomes of respondents in their early forties. We find membership in the lowest job satisfaction trajectory group to be negatively associated with all five mental health outcomes, supporting the accumulation of risks life course model. Those in the upward job satisfaction trajectory group have similar health outcomes to those in the high job satisfaction trajectory group, supporting the social mobility life course model. Overall, we find the relationship between job satisfaction trajectories and health to be stronger for mental health compared to physical health. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effect of initial stress induced during the steel manufacturing process on the welding residual stress in multi-pass butt welding

Directory of Open Access Journals (Sweden)

Jeong-ung Park

2018-03-01

Full Text Available A residual stress generated in the steel structure is broadly categorized into initial residual stress during manufacturing steel material, welding residual stress caused by welding, and heat treatment residual stress by heat treatment. Initial residual stresses induced during the manufacturing process is combined with welding residual stress or heat treatment residual stress, and remained as a final residual stress. Because such final residual stress affects the safety and strength of the structure, it is of utmost importance to measure or predict the magnitude of residual stress, and to apply this point on the design of the structure. In this study, the initial residual stress of steel structures having thicknesses of 25 mm and 70 mm during manufacturing was measured in order to investigate initial residual stress (hereinafter, referred to as initial stress. In addition, thermal elastic plastic FEM analysis was performed with this initial condition, and the effect of initial stress on the welding residual stress was investigated. Further, the reliability of the FE analysis result, considering the initial stress and welding residual stress for the steel structures having two thicknesses, was validated by comparing it with the measured results. In the vicinity of the weld joint, the initial stress is released and finally controlled by the weld residual stress. On the other hand, the farther away from the weld joint, the greater the influence of the initial stress. The range in which the initial stress affects the weld residual stress was not changed by the initial stress. However, in the region where the initial stress occurs in the compressive stress, the magnitude of the weld residual compressive stress varies with the compression or tension of the initial stress. The effect of initial stress on the maximum compression residual stress was far larger when initial stress was considered in case of a thickness of 25 mm with a value of 180�

DNABIT Compress - Genome compression algorithm.

Science.gov (United States)

Rajarajeswari, Pothuraju; Apparao, Allam

2011-01-22

Data compression is concerned with how information is organized in data. Efficient storage means removal of redundancy from the data being stored in the DNA molecule. Data compression algorithms remove redundancy and are used to understand biologically important molecules. We present a compression algorithm, "DNABIT Compress" for DNA sequences based on a novel algorithm of assigning binary bits for smaller segments of DNA bases to compress both repetitive and non repetitive DNA sequence. Our proposed algorithm achieves the best compression ratio for DNA sequences for larger genome. Significantly better compression results show that "DNABIT Compress" algorithm is the best among the remaining compression algorithms. While achieving the best compression ratios for DNA sequences (Genomes),our new DNABIT Compress algorithm significantly improves the running time of all previous DNA compression programs. Assigning binary bits (Unique BIT CODE) for (Exact Repeats, Reverse Repeats) fragments of DNA sequence is also a unique concept introduced in this algorithm for the first time in DNA compression. This proposed new algorithm could achieve the best compression ratio as much as 1.58 bits/bases where the existing best methods could not achieve a ratio less than 1.72 bits/bases.

Compressibility, turbulence and high speed flow

CERN Document Server

Gatski, Thomas B

2009-01-01

This book introduces the reader to the field of compressible turbulence and compressible turbulent flows across a broad speed range through a unique complimentary treatment of both the theoretical foundations and the measurement and analysis tools currently used. For the computation of turbulent compressible flows, current methods of averaging and filtering are presented so that the reader is exposed to a consistent development of applicable equation sets for both the mean or resolved fields as well as the transport equations for the turbulent stress field. For the measurement of turbulent compressible flows, current techniques ranging from hot-wire anemometry to PIV are evaluated and limitations assessed. Characterizing dynamic features of free shear flows, including jets, mixing layers and wakes, and wall-bounded flows, including shock-turbulence and shock boundary-layer interactions, obtained from computations, experiments and simulations are discussed. Key features: * Describes prediction methodologies in...

Jamming by compressing a system of granular crosses

Science.gov (United States)

Zheng, Hu; Wang, Dong; Barés, Jonathan; Behringer, Robert

2017-06-01

A disordered stress-free granular packing can be jammed, transformed into a mechanically rigid structure, by increasing the density of particles or by applying shear deformation. The jamming behavior of systems made of 2D circular discs has been investigated in detail, but very little is known about jamming for non-spherical particles, and particularly, non-convex particles. Here, we perform an experimental study on jamming by compression of a system of quasi-2D granular crosses made of photo-elastic crosses. We measure the pressure evolution during cyclic compression and decompression. The Jamming packing fraction of these quasi-2D granular crosses is ϕJ ≃ 0.475, which is much smaller than the value ϕJ ≃ 0.84 for-2D granular disks. The packing fraction shifts systematically to higher values under compressive cycling, corresponding to systematic shifts in the stress-strain response curves. Associated with these shifts are rotations of the crosses, with minimal changes in their centers of mass.

Advances in compressible turbulent mixing

International Nuclear Information System (INIS)

Dannevik, W.P.; Buckingham, A.C.; Leith, C.E.

1992-01-01

This volume includes some recent additions to original material prepared for the Princeton International Workshop on the Physics of Compressible Turbulent Mixing, held in 1988. Workshop participants were asked to emphasize the physics of the compressible mixing process rather than measurement techniques or computational methods. Actual experimental results and their meaning were given precedence over discussions of new diagnostic developments. Theoretical interpretations and understanding were stressed rather than the exposition of new analytical model developments or advances in numerical procedures. By design, compressibility influences on turbulent mixing were discussed--almost exclusively--from the perspective of supersonic flow field studies. The papers are arranged in three topical categories: Foundations, Vortical Domination, and Strongly Coupled Compressibility. The Foundations category is a collection of seminal studies that connect current study in compressible turbulent mixing with compressible, high-speed turbulent flow research that almost vanished about two decades ago. A number of contributions are included on flow instability initiation, evolution, and transition between the states of unstable flow onset through those descriptive of fully developed turbulence. The Vortical Domination category includes theoretical and experimental studies of coherent structures, vortex pairing, vortex-dynamics-influenced pressure focusing. In the Strongly Coupled Compressibility category the organizers included the high-speed turbulent flow investigations in which the interaction of shock waves could be considered an important source for production of new turbulence or for the enhancement of pre-existing turbulence. Individual papers are processed separately

Advances in compressible turbulent mixing

Energy Technology Data Exchange (ETDEWEB)

Dannevik, W.P.; Buckingham, A.C.; Leith, C.E. [eds.

1992-01-01

This volume includes some recent additions to original material prepared for the Princeton International Workshop on the Physics of Compressible Turbulent Mixing, held in 1988. Workshop participants were asked to emphasize the physics of the compressible mixing process rather than measurement techniques or computational methods. Actual experimental results and their meaning were given precedence over discussions of new diagnostic developments. Theoretical interpretations and understanding were stressed rather than the exposition of new analytical model developments or advances in numerical procedures. By design, compressibility influences on turbulent mixing were discussed--almost exclusively--from the perspective of supersonic flow field studies. The papers are arranged in three topical categories: Foundations, Vortical Domination, and Strongly Coupled Compressibility. The Foundations category is a collection of seminal studies that connect current study in compressible turbulent mixing with compressible, high-speed turbulent flow research that almost vanished about two decades ago. A number of contributions are included on flow instability initiation, evolution, and transition between the states of unstable flow onset through those descriptive of fully developed turbulence. The Vortical Domination category includes theoretical and experimental studies of coherent structures, vortex pairing, vortex-dynamics-influenced pressure focusing. In the Strongly Coupled Compressibility category the organizers included the high-speed turbulent flow investigations in which the interaction of shock waves could be considered an important source for production of new turbulence or for the enhancement of pre-existing turbulence. Individual papers are processed separately.

Effect of compressive stress on stability of N-doped p-type ZnO

Energy Technology Data Exchange (ETDEWEB)

Chen Xingyou [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 3888 Dongnanhu Road, Changchun 130033 (China); Graduate School of the Chinese Academy of Sciences, Beijing 100049 (China); Zhang Zhenzhong; Jiang Mingming; Wang Shuangpeng; Li Binghui; Shan Chongxin; Liu Lei; Zhao Dongxu; Shen Dezhen [Key Laboratory of Excited State Processes, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 3888 Dongnanhu Road, Changchun 130033 (China); Yao Bin [State Key Laboratory of Superhard Materials and College of Physics, Jilin University, Changchun 130023 (China)

2011-08-29

Nitrogen-doped p-type zinc oxide (p-ZnO:N) thin films were fabricated on a-/c-plane sapphire (a-/c-Al{sub 2}O{sub 3}) by plasma-assisted molecular beam epitaxy. Hall-effect measurements show that the p-type ZnO:N on c-Al{sub 2}O{sub 3} degenerated into n-type after a preservation time; however, the one grown on a-Al{sub 2}O{sub 3} showed good stability. The conversion of conductivity in the one grown on c-Al{sub 2}O{sub 3} ascribed to the faster disappearance of N{sub O} and the growing N{sub 2(O)}, which is demonstrated by x-ray photoelectron spectroscopy (XPS). Compressive stress, caused by lattice misfit, was revealed by Raman spectra and optical absorption spectra, and it was regarded as the root of the instability in ZnO:N.

Pathways to change: Use trajectories following trauma-informed treatment of women with co-occurring post-traumatic stress disorder and substance use disorders.

Science.gov (United States)

López-Castro, Teresa; Hu, Mei-Chen; Papini, Santiago; Ruglass, Lesia M; Hien, Denise A

2015-05-01

Despite advances towards integration of care for women with co-occurring substance use disorder (SUD) and post-traumatic stress disorder (PTSD), low abstinence rates following SUD/PTSD treatment remain the norm. The utility of investigating distinct substance use trajectories is a critical innovation in the detection and refining of effective interventions for this clinical population. The present study reanalysed data from the largest randomised clinical trial to date for co-occurring SUD and PTSD in women (National Drug Abuse Treatment Clinical Trials Network; Women and Trauma Study). Randomised participants (n = 353) received one of two interventions in addition to treatment as usual for SUD: (i) trauma-informed integrative treatment for PTSD/SUD; or (ii) an active control psychoeducation course on women's health. The present study utilised latent growth mixture models (LGMM) with multiple groups to estimate women's substance use patterns during the 12-month follow-up period. Findings provided support for three different trajectories of substance use in the post-treatment year: (i) consistently low likelihood and use frequency; (ii) consistently high likelihood and use frequency; and (iii) high likelihood and moderate use frequency. Covariate analyses revealed improvement in PTSD severity was associated with membership in a specific substance use trajectory, although receiving trauma-informed treatment was not. Additionally, SUD severity, age and after-care efforts were shown to be related to trajectory membership. Findings highlight the necessity of accounting for heterogeneity in post-treatment substance use, relevance of trauma-informed care in SUD recovery and benefits of incorporating methodologies like LGMM when evaluating SUD treatment outcomes. © 2015 Australasian Professional Society on Alcohol and other Drugs.

Design for limit stresses of orange fruits (Citrus sinensis under axial and radial compression as related to transportation and storage design

Directory of Open Access Journals (Sweden)

Christopher Chukwutoo Ihueze

2017-01-01

Full Text Available This article employed the Hertz contact stress theory and the finite element method to evaluate the maximum contact pressure and the limit stresses of orange fruit under transportation and storage. The elastic properties of orange fruits subjected to axial and axial contact were measured such that elastic limit force, elastic modulus, Poisson’s ratio and bioyield stress were obtained as 18 N, 0.691 MPa, 0.367, 0.009 MPa for axial compression and for radial loading were 15.69 N, 0.645 MPa, 0.123, 0.010 MPa. The Hertz maximum contact pressure was estimated for axial and radial contacts as 0.036 MPa. The estimated limiting yield stress estimated as von Mises stresses for the induced surface stresses of the orange topologies varied from 0.005 MPa–0.03 MPa. Based on the distortion energy theory (DET the yield strength of orange fruit is recommended as 0.03 MPa while based on the maximum shear stress theory (MSST is 0.01 MPa for the design of orange transportation and storage system.

Elastic-plastic transition on rotating spherical shells in dependence of compressibility

Directory of Open Access Journals (Sweden)

Thakur Pankaj

2017-01-01

Full Text Available The purpose of this paper is to establish the mathematical model on the elastic-plastic transitions occurring in the rotating spherical shells based on compressibility of materials. The paper investigates the elastic-plastic stresses and angular speed required to start yielding in rotating shells for compressible and incompressible materials. The paper is based on the non-linear transition theory of elastic-plastic shells given by B.R. Seth. The elastic-plastic transition obtained is treated as an asymptotic phenomenon at critical points & the solution obtained at these points generates stresses. The solution obtained does not require the use of semi-empirical yield condition like Tresca or Von Mises or other certain laws. Results are obtained numerically and depicted graphically. It has been observed that Rotating shells made of the incompressible material are on the safer side of the design as compared to rotating shells made of compressible material. The effect of density variation has been discussed numerically on the stresses. With the effect of density variation parameter, rotating spherical shells start yielding at the internal surface with the lower values of the angular speed for incompressible/compressible materials.

Mechanical Behavior of Red Sandstone under Incremental Uniaxial Cyclical Compressive and Tensile Loading

Directory of Open Access Journals (Sweden)

Baoyun Zhao

2017-01-01

Full Text Available Uniaxial experiments were carried out on red sandstone specimens to investigate their short-term and creep mechanical behavior under incremental cyclic compressive and tensile loading. First, based on the results of short-term uniaxial incremental cyclic compressive and tensile loading experiments, deformation characteristics and energy dissipation were analyzed. The results show that the stress-strain curve of red sandstone has an obvious memory effect in the compressive and tensile loading stages. The strains at peak stresses and residual strains increase with the cycle number. Energy dissipation, defined as the area of the hysteresis loop in the stress-strain curves, increases nearly in a power function with the cycle number. Creep test of the red sandstone was also conducted. Results show that the creep curve under each compressive or tensile stress level can be divided into decay and steady stages, which cannot be described by the conventional Burgers model. Therefore, an improved Burgers creep model of rock material is constructed through viscoplastic mechanics, which agrees very well with the experimental results and can describe the creep behavior of red sandstone better than the Burgers creep model.

A Constitutive Model for Unsaturated soils based on a Compressibility Framework dependent on Suction and Degree of Saturation

Directory of Open Access Journals (Sweden)

Sitarenios Panagiotis

2016-01-01

Full Text Available The Modified Cam Clay model is extended to account for the behaviour of unsaturated soils using Bishop’s stress. To describe the Loading – Collapse behaviour, the model incorporates a compressibility framework with suction and degree of saturation dependent compression lines. For simplicity, the present paper describes the model in the triaxial stress space with characteristic simulations of constant suction compression and triaxial tests, as well as wetting tests. The model reproduces an evolving post yield compressibility under constant suction compression, and thus, can adequately describe a maximum of collapse.

Experimental Characteristics of Dry Stack Masonry under Compression and Shear Loading

Directory of Open Access Journals (Sweden)

Kun Lin

2015-12-01

Full Text Available The behavior of dry stack masonry (DSM is influenced by the interaction of the infill with the frame (especially the joints between bricks, which requires further research. This study investigates the compression and shear behaviors of DSM. First, a series of compression tests were carried out on both masonry prism with mortar (MP_m and DSM prism (MP_ds. The failure mode of each prism was determined. Different from the MP_m, the stress-strain relationship of the MP_ds was characterized by an upward concavity at the initial stage. The compression strength of the MP_ds was slightly reduced by 15%, while the elastic modulus was reduced by over 62%. In addition, 36 shear-compression tests were carried out under cyclic loads to emphasize the influence of various loads on the shear-compression behavior of DSM. The results showed that the Mohr-Coulomb friction law adequately represents the failure of dry joints at moderate stress levels, and the varying friction coefficients under different load amplitudes cannot be neglected. The experimental setup and results are valuable for further research.

Experimental Characteristics of Dry Stack Masonry under Compression and Shear Loading.

Science.gov (United States)

Lin, Kun; Totoev, Yuri Zarevich; Liu, Hongjun; Wei, Chunli

2015-12-12

The behavior of dry stack masonry (DSM) is influenced by the interaction of the infill with the frame (especially the joints between bricks), which requires further research. This study investigates the compression and shear behaviors of DSM. First, a series of compression tests were carried out on both masonry prism with mortar (MP_m) and DSM prism (MP_ds). The failure mode of each prism was determined. Different from the MP_m, the stress-strain relationship of the MP_ds was characterized by an upward concavity at the initial stage. The compression strength of the MP_ds was slightly reduced by 15%, while the elastic modulus was reduced by over 62%. In addition, 36 shear-compression tests were carried out under cyclic loads to emphasize the influence of various loads on the shear-compression behavior of DSM. The results showed that the Mohr-Coulomb friction law adequately represents the failure of dry joints at moderate stress levels, and the varying friction coefficients under different load amplitudes cannot be neglected. The experimental setup and results are valuable for further research.

Predicting the compressibility behaviour of tire shred samples for landfill applications.

Science.gov (United States)

Warith, M A; Rao, Sudhakar M

2006-01-01

Tire shreds have been used as an alternative to crushed stones (gravel) as drainage media in landfill leachate collection systems. The highly compressible nature of tire shreds (25-47% axial strain on vertical stress applications of 20-700 kPa) may reduce the thickness of the tire shred drainage layer to less than 300 mm (minimum design requirement) during the life of the municipal solid waste landfill. There hence exists a need to predict axial strains of tire shred samples in response to vertical stress applications so that the initial thickness of the tire shred drainage layer can be corrected for compression. The present study performs one-dimensional compressibility tests on four tire shred samples and compares the results with stress/strain curves from other studies. The stress/strain curves are developed into charts for choosing the correct initial thickness of tire shred layers that maintain the minimum thickness of 300 mm throughout the life of the landfill. The charts are developed for a range of vertical stresses based on the design height of municipal waste cell and bulk unit weight of municipal waste. Experimental results also showed that despite experiencing large axial strains, the average permeability of the tire shred sample consistently remained two to three orders of magnitude higher than the design performance criterion of 0.01cm/s for landfill drainage layers. Laboratory experiments, however, need to verify whether long-term chemical and bio-chemical reactions between landfill leachate and the tire shred layer will deteriorate their mechanical functions (hydraulic conductivity, compressibility, strength) beyond permissible limits for geotechnical applications.

A trajectory description of quantum processes. II. Applications. A Bohmian perspective

Energy Technology Data Exchange (ETDEWEB)

Sanz, Angel S.; Miret-Artes, Salvador [CSIC, Madrid (Spain). Inst. de Fisica Fundamental (IFF-CSIC)

2014-07-01

Presents a thorough introduction to, and treatment of, trajectory-based quantum-mechanical calculations. Useful for a wide range of scattering problems. Presents the applications of the trajectory description of basic quantum processes. Trajectory-based formalisms are an intuitively appealing way of describing quantum processes because they allow the use of ''classical'' concepts. Beginning as an introductory level suitable for students, this two-volume monograph presents (1) the fundamentals and (2) the applications of the trajectory description of basic quantum processes. This second volume is focussed on simple and basic applications of quantum processes such as interference and diffraction of wave packets, tunneling, diffusion and bound-state and scattering problems. The corresponding analysis is carried out within the Bohmian framework. By stressing its interpretational aspects, the book leads the reader to an alternative and complementary way to better understand the underlying quantum dynamics.

Isentropic compression studies using the NHMFL single turn

Energy Technology Data Exchange (ETDEWEB)

Tasker, Douglas G [Los Alamos National Laboratory; Mielke, Charles [Los Alamos National Laboratory; Rodriguez, George [Los Alamos National Laboratory; Rickel, Dwight [Los Alamos National Laboratory

2010-10-19

Magnetic isentropic compression experiments (ICE) provide the most accurate shock free compression data for materials at megabar stresses. Recent ICE experiments performed on the Sandia Z-machine (Asay, 1999) and at the Los Alamos High Explosive Pulsed Power facility (Tasker, 2006) are providing our nation with data on material properties in extreme dynamic high stress environments. The LANL National High Magnetic Field Laboratory (NHMFL) can offer a less complex ICE experiment at high stresses (up to {approx}1Mbar) with a high sample throughput and relatively low cost. This is not to say that the NHMFL technique will replace the other methods but rather complement them. For example, NHMFL-ICE is ideal for the development of advanced diagnostics, e.g., to detect phase changes. We will discuss the physics of the NHMFL-ICE experiments and present data from the first proof-of-principle experiments that were performed in September 2010.

Modeling and control of tissue compression and temperature for automation in robot-assisted surgery.

Science.gov (United States)

Sinha, Utkarsh; Li, Baichun; Sankaranarayanan, Ganesh

2014-01-01

Robotic surgery is being used widely due to its various benefits that includes reduced patient trauma and increased dexterity and ergonomics for the operating surgeon. Making the whole or part of the surgical procedure autonomous increases patient safety and will enable the robotic surgery platform to be used in telesurgery. In this work, an Electrosurgery procedure that involves tissue compression and application of heat such as the coaptic vessel closure has been automated. A MIMO nonlinear model characterizing the tissue stiffness and conductance under compression was feedback linearized and tuned PID controllers were used to control the system to achieve both the displacement and temperature constraints. A reference input for both the constraints were chosen as a ramp and hold trajectory which reflect the real constraints that exist in an actual surgical procedure. Our simulations showed that the controllers successfully tracked the reference trajectories with minimal deviation and in finite time horizon. The MIMO system with controllers developed in this work can be used to drive a surgical robot autonomously and perform electrosurgical procedures such as coaptic vessel closures.

Compressive behavior of pervious concretes and a quantification of the influence of random pore structure features

International Nuclear Information System (INIS)

Deo, Omkar; Neithalath, Narayanan

2010-01-01

Research highlights: → Identified the relevant pore structure features of pervious concretes, provided methodologies to extract those, and quantified the influence of these features on compressive response. → A model for stress-strain relationship of pervious concretes, and relationship between model parameters and parameters of the stress-strain relationship developed. → Statistical model for compressive strength as a function of pore structure features; and a stochastic model for the sensitivity of pore structure features in strength prediction. - Abstract: Properties of a random porous material such as pervious concrete are strongly dependent on its pore structure features, porosity being an important one among them. This study deals with developing an understanding of the material structure-compressive response relationships in pervious concretes. Several pervious concrete mixtures with different pore structure features are proportioned and subjected to static compression tests. The pore structure features such as pore area fractions, pore sizes, mean free spacing of the pores, specific surface area, and the three-dimensional pore distribution density are extracted using image analysis methods. The compressive stress-strain response of pervious concretes, a model to predict the stress-strain response, and its relationship to several of the pore structure features are outlined. Larger aggregate sizes and increase in paste volume fractions are observed to result in increased compressive strengths. The compressive response is found to be influenced by the pore sizes, their distributions and spacing. A statistical model is used to relate the compressive strength to the relevant pore structure features, which is then used as a base model in a Monte-Carlo simulation to evaluate the sensitivity of the predicted compressive strength to the model terms.

Study on residual stress across the pipes' thickness using outer surface rapid heating. Development of pipe outer surface irradiated laser stress improvement process (L-SIP)

International Nuclear Information System (INIS)

Ohta, Takahiro; Terasaki, Toshio

2009-01-01

The new process called L-SIP (outer surface irradiated Laser Stress Improvement Process) is developed to improve the tensile residual stress of the inner surface near the butt welded joints of pipes in the compression stress. The temperature gradient occurs in the thickness of pipes in heating the outer surface rapidly by laser beam. By the thermal expansion difference between the inner surface and the outer surface, the compression plastic strain generates near the outer surface and the tensile plastic strain generates near the inner surface of pipes. The compression stress occurs near the inner surface of pipes by the plastic deformation. In this paper, the theoretical equation which calculates residual stress distribution from the inherent strain distribution in the thickness of pipes is derived. And, the relation between the distribution of temperature and the residual stress in the thickness is examined for various pipes size. (1) By rapidly heating from the outer surface, the residual stress near the inner surface of the pipe is improved to the compression stress. (2) Pipes size hardly affects the distribution of the residual stress in the stainless steel pipes for piping (JISG3459). (3) The temperature rising area from the outside is smaller, the area of the compression residual stress near the inner surface becomes wider. (author)

Estimation of fracture conditions of ceramics by thermal shock with laser beams based on the maximum compressive stress criterion

International Nuclear Information System (INIS)

Akiyama, Shigeru; Amada, Shigeyasu.

1992-01-01

Structural ceramics are attracting attention in the development of space planes, aircraft and nuclear fusion reactors because they have excellent wear-resistant and heat-resistant characteristics. However, in some applications it is anticipated that they will be exposed to very-high-temperature environments of the order of thousands of degrees. Therefore, it is very important to investigate their thermal shock characteristics. In this report, the distributions of temperatures and thermal stresses of cylindrically shaped ceramics under irradiation by laser beams are discussed using the finite-element computer code (MARC) with arbitrary quadrilateral axisymmetric ring elements. The relationships between spot diameters of laser beams and maximum values of compressive thermal stresses are derived for various power densities. From these relationships, a critical fracture curve is obtained, and it is compared with the experimental results. (author)

Characterization of the constitutive behavior of municipal solid waste considering particle compressibility.

Science.gov (United States)

Lü, Xilin; Zhai, Xinle; Huang, Maosong

2017-11-01

This paper presents a characterization of the mechanical behavior of municipal solid waste (MSW) under consolidated drained and undrained triaxial conditions. The constitutive model was established based on a deviatoric hardening plasticity model. A power form function and incremental hyperbolic form function were proposed to describe the shear strength and the hardening role of MSW. The stress ratio that corresponds to the zero dilatancy was not fixed but depended on mean stress, making the Rowe's rule be able to describe the stress-dilatancy of MSW. A pore water pressure reduction coefficient, which attributed to the compressibility of a particle and the solid matrix, was introduced to the effective stress formulation to modify the Terzaghi's principle. The effects of particle compressibility and solid matrix compressibility on the undrained behavior of MSW were analyzed by parametric analysis, and the changing characteristic of stress-path, stress-strain, and pore-water pressure were obtained. The applicability of the proposed model on MSW under drained and undrained conditions was verified by model predictions of three triaxial tests. The comparison between model simulations and experiments indicated that the proposed model can capture the observed different characteristics of MSW response from normal soil, such as nonlinear shear strength, pressure dependent stress dilatancy, and the reduced value of pore water pressure. Copyright © 2017 Elsevier Ltd. All rights reserved.

Residual stress measurement in 304 stainless steel weld overlay pipes

International Nuclear Information System (INIS)

Yen, H.J.; Lin, M.C.C.; Chen, L.J.

1996-01-01

Welding overlay repair (WOR) is commonly employed to rebuild piping systems suffering from intergranular stress corrosion cracking (IGSCC). To understand the effects of this repair, it is necessary to investigate the distribution of residual stresses in the welding pipe. The overlay welding technique must induce compressive residual stress at the inner surface of the welded pipe to prevent IGSCC. To understand the bulk residual stress distribution, the stress profile as a function of location within wall is examined. In this study the full destructive residual stress measurement technique -- a cutting and sectioning method -- is used to determine the residual stress distribution. The sample is type 304 stainless steel weld overlay pipe with an outside diameter of 267 mm. A pipe segment is cut from the circular pipe; then a thin layer is removed axially from the inner to the outer surfaces until further sectioning is impractical. The total residual stress is calculated by adding the stress relieved by cutting the section away to the stress relieved by axially sectioning. The axial and hoop residual stresses are compressive at the inner surface of the weld overlay pipe. Compressive stress exists not only at the surface but is also distributed over most of the pipe's cross section. On the one hand, the maximum compressive hoop residual stress appears at the pipe's inner surface. The thermal-mechanical induced crack closure from significant compressive residual stress is discussed. This crack closure can thus prevent IGSCC very effectively

The long range migration of hydrogen through Zircaloy in response to tensile and compressive stress gradients

International Nuclear Information System (INIS)

Kammenzind, B.F.; Berquist, B.M.; Bajaj, R.; Kreyns, P.H.; Franklin, D.G.

1998-01-01

Zircaloy-4, which is used widely as a core structural material in pressurized water reactors (PWRs), picks up hydrogen during service. Hydrogen solubility in Zircaloy-4 is low and zirconium hydride phases precipitate after the Zircaloy-4 lattice becomes supersaturated with hydrogen. These hydrides embrittle the Zircaloy-4, degrading its mechanical performance as a structural material. Because hydrogen can move rapidly through the Zircaloy-4 lattice, the potential exists for large concentrations of hydride to accumulate in local regions of a Zircaloy component remote from its point of entry into the component. Much has been reported in the literature regarding the long range migration of hydrogen through Zircaloy under concentration gradients and temperature gradients. Relatively little has been reported, however, regarding the long range migration of hydrogen under stress gradients. This paper presents experimental results regarding the long range migration of hydrogen through Zircaloy in response to both tensile and compressive stress gradients. The importance of this driving force for hydrogen migration relative to concentration and thermal gradients is discussed

Implementation of 3D spatial indexing and compression in a large-scale molecular dynamics simulation database for rapid atomic contact detection

Directory of Open Access Journals (Sweden)

Toofanny Rudesh D

2011-08-01

Full Text Available Abstract Background Molecular dynamics (MD simulations offer the ability to observe the dynamics and interactions of both whole macromolecules and individual atoms as a function of time. Taken in context with experimental data, atomic interactions from simulation provide insight into the mechanics of protein folding, dynamics, and function. The calculation of atomic interactions or contacts from an MD trajectory is computationally demanding and the work required grows exponentially with the size of the simulation system. We describe the implementation of a spatial indexing algorithm in our multi-terabyte MD simulation database that significantly reduces the run-time required for discovery of contacts. The approach is applied to the Dynameomics project data. Spatial indexing, also known as spatial hashing, is a method that divides the simulation space into regular sized bins and attributes an index to each bin. Since, the calculation of contacts is widely employed in the simulation field, we also use this as the basis for testing compression of data tables. We investigate the effects of compression of the trajectory coordinate tables with different options of data and index compression within MS SQL SERVER 2008. Results Our implementation of spatial indexing speeds up the calculation of contacts over a 1 nanosecond (ns simulation window by between 14% and 90% (i.e., 1.2 and 10.3 times faster. For a 'full' simulation trajectory (51 ns spatial indexing reduces the calculation run-time between 31 and 81% (between 1.4 and 5.3 times faster. Compression resulted in reduced table sizes but resulted in no significant difference in the total execution time for neighbour discovery. The greatest compression (~36% was achieved using page level compression on both the data and indexes. Conclusions The spatial indexing scheme significantly decreases the time taken to calculate atomic contacts and could be applied to other multidimensional neighbor discovery

Implementation of 3D spatial indexing and compression in a large-scale molecular dynamics simulation database for rapid atomic contact detection.

Science.gov (United States)

Toofanny, Rudesh D; Simms, Andrew M; Beck, David A C; Daggett, Valerie

2011-08-10

Molecular dynamics (MD) simulations offer the ability to observe the dynamics and interactions of both whole macromolecules and individual atoms as a function of time. Taken in context with experimental data, atomic interactions from simulation provide insight into the mechanics of protein folding, dynamics, and function. The calculation of atomic interactions or contacts from an MD trajectory is computationally demanding and the work required grows exponentially with the size of the simulation system. We describe the implementation of a spatial indexing algorithm in our multi-terabyte MD simulation database that significantly reduces the run-time required for discovery of contacts. The approach is applied to the Dynameomics project data. Spatial indexing, also known as spatial hashing, is a method that divides the simulation space into regular sized bins and attributes an index to each bin. Since, the calculation of contacts is widely employed in the simulation field, we also use this as the basis for testing compression of data tables. We investigate the effects of compression of the trajectory coordinate tables with different options of data and index compression within MS SQL SERVER 2008. Our implementation of spatial indexing speeds up the calculation of contacts over a 1 nanosecond (ns) simulation window by between 14% and 90% (i.e., 1.2 and 10.3 times faster). For a 'full' simulation trajectory (51 ns) spatial indexing reduces the calculation run-time between 31 and 81% (between 1.4 and 5.3 times faster). Compression resulted in reduced table sizes but resulted in no significant difference in the total execution time for neighbour discovery. The greatest compression (~36%) was achieved using page level compression on both the data and indexes. The spatial indexing scheme significantly decreases the time taken to calculate atomic contacts and could be applied to other multidimensional neighbor discovery problems. The speed up enables on-the-fly calculation

Mechanical behavior and microstructure during compression of semi-solid ZK60-RE magnesium alloy at high solid content

International Nuclear Information System (INIS)

Shan Weiwei; Luo Shoujing

2007-01-01

Mechanical behavior during compression of semi-solid ZK60-RE magnesium alloy at high solid content is researched in this paper. The alloy was prepared from ZK60 alloy and rare earth elements by casting, equal channel angular extruding, and liquidus forging. Semi-solid isothermal pre-treatment was carried out to make the grains globular before the compression. Here, several groups of true strain-true stress curves with different variables during compression are given to make comparisons of their mechanical behaviors. Liquid paths were the most essential to deformation, and its variation during compression depends on the strain rate. Here, thixotropic strength is defined as the true stress at the first peak in the true stress-true strain curve

Wearing graduated compression stockings augments cutaneous vasodilation in heat-stressed resting humans.

Science.gov (United States)

Fujii, Naoto; Nikawa, Toshiya; Tsuji, Bun; Kondo, Narihiko; Kenny, Glen P; Nishiyasu, Takeshi

2017-05-01

We investigated whether graduated compression induced by stockings enhances cutaneous vasodilation in passively heated resting humans. Nine habitually active young men were heated at rest using water-perfusable suits, resulting in a 1.0 °C increase in body core temperature. Heating was repeated twice on separate occasions while wearing either (1) stockings that cause graduated compression (pressures of 26.4 ± 5.3, 17.5 ± 4.4, and 6.1 ± 2.0 mmHg at the ankle, calf, and thigh, respectively), or (2) loose-fitting stockings without causing compression (Control). Forearm vascular conductance during heating was evaluated by forearm blood flow (venous occlusion plethysmography) divided by mean arterial pressure to estimate heat-induced cutaneous vasodilation. Body core (esophageal), skin, and mean body temperatures were measured continuously. Compared to the Control, forearm vascular conductance during heating was higher with graduated compression stockings (e.g., 23.2 ± 5.5 vs. 28.6 ± 5.8 units at 45 min into heating, P = 0.001). In line with this, graduated compression stockings resulted in a greater sensitivity (27.5 ± 8.3 vs. 34.0 ± 9.4 units °C -1 , P = 0.02) and peak level (25.5 ± 5.8 vs. 29.7 ± 5.8 units, P = 0.004) of cutaneous vasodilation as evaluated from the relationship between forearm vascular conductance with mean body temperature. In contrast, the mean body temperature threshold for increases in forearm vascular conductance did not differ between the Control and graduated compression stockings (36.5 ± 0.1 vs. 36.5 ± 0.2 °C, P = 0.85). Our results show that graduated compression associated with the use of stockings augments cutaneous vasodilation by modulating sensitivity and peak level of cutaneous vasodilation in relation to mean body temperature. However, the effect of these changes on whole-body heat loss remains unclear.

Experimental investigation and empirical modelling of FDM process for compressive strength improvement

Directory of Open Access Journals (Sweden)

Anoop K. Sood

2012-01-01

Full Text Available Fused deposition modelling (FDM is gaining distinct advantage in manufacturing industries because of its ability to manufacture parts with complex shapes without any tooling requirement and human interface. The properties of FDM built parts exhibit high dependence on process parameters and can be improved by setting parameters at suitable levels. Anisotropic and brittle nature of build part makes it important to study the effect of process parameters to the resistance to compressive loading for enhancing service life of functional parts. Hence, the present work focuses on extensive study to understand the effect of five important parameters such as layer thickness, part build orientation, raster angle, raster width and air gap on the compressive stress of test specimen. The study not only provides insight into complex dependency of compressive stress on process parameters but also develops a statistically validated predictive equation. The equation is used to find optimal parameter setting through quantum-behaved particle swarm optimization (QPSO. As FDM process is a highly complex one and process parameters influence the responses in a non linear manner, compressive stress is predicted using artificial neural network (ANN and is compared with predictive equation.

The impact of life stress on adult depression and anxiety is dependent on gender and timing of exposure.

Science.gov (United States)

Herbison, Carly E; Allen, Karina; Robinson, Monique; Newnham, John; Pennell, Craig

2017-10-01

There is debate about the relative importance of timing of stressful events prenatally and over the life course and risk for subsequent depressive/anxious illness. The aim of this study was to examine the relative roles of prenatal stress and postnatal stress trajectories in predicting depression and anxiety in early adulthood in males and females. Exposure to life stress events was examined in the Western Australian Pregnancy Cohort (Raine) Study during pregnancy and ages 1, 2, 3, 5, 8, 10, 14, and 17 years. At age 20, offspring completed the Depression Anxiety Stress Scale. Prenatal stress and trajectories of stress events from age 1 to 17 were analyzed in linear regression analyses. Five postnatal stress trajectories were identified. In females, medium to high chronic stress exposure or exposure during puberty/adolescence predicted depression and anxiety symptoms while low or reduced stress exposure over the life course did not, after adjustment for relevant confounders. High stress early in pregnancy contributed to male depression/anxiety symptoms independent of postnatal stress trajectory. In females, postnatal stress trajectory was more important than prenatal stress in predicting depression/anxiety symptoms. Interventions focused on reducing and managing stress events around conception/pregnancy and exposure to chronic stress are likely to have beneficial outcomes on rates of depression and anxiety in adults.

Stress in ion-implanted CVD Si3N4 films

International Nuclear Information System (INIS)

EerNisse, E.P.

1977-01-01

The compressive stress buildup caused in chemical-vapor-deposited (CVD) Si 3 N 4 films by ion implantation is shown to be caused entirely by atomic collision effects, ionization effects being unimportant. The stress introduction rate is shown to be independent of CVD processing variables and O content of the film. The maximum attainable compressive stress change is 3.5 x 10 10 dyn/cm 2 , resulting in a maximum net compressive stress of 2 x 10 10 dyn/cm 2 for films on Si where the as-deposited films inherently have 1.5 x 10 10 dyn/cm 2 tensile stress before ion implantation. Results are presented which show that O in the films inhibits thermal annealing of the ion-implantation-induced compressive stress. Results for introduction rate and annealing effects are presented in normalized form so that workers can use the effects for intentional stress level adjustment in the films to reduce probability of cracking and detachment

Latent trajectories of internalizing symptoms from preschool to school age: A multi-informant study in a high-risk sample.

Science.gov (United States)

Klein, Annette M; Schlesier-Michel, Andrea; Otto, Yvonne; White, Lars O; Andreas, Anna; Sierau, Susan; Bergmann, Sarah; Perren, Sonja; von Klitzing, Kai

2018-04-29

Recent proposals suggest early adversity sets in motion particularly chronic and neurobiologically distinct trajectories of internalizing symptoms. However, few prospective studies in high-risk samples delineate distinct trajectories of internalizing symptoms from preschool age onward. We examined trajectories in a high-risk cohort, oversampled for internalizing symptoms, several preschool risk/maintenance factors, and school-age outcomes. Parents of 325 children completed the Strengths and Difficulties Questionnaire on up to four waves of data collection from preschool (3-5 years) to school age (8-9 years) and Preschool Age Psychiatric Assessment interviews at both ages. Multi-informant data were collected on risk factors and symptoms. Growth mixture modelling identified four trajectory classes of internalizing symptoms with stable low, rising low-to-moderate, stable moderate, and stable high symptoms. Children in the stable high symptom trajectory manifested clinically relevant internalizing symptoms, mainly diagnosed with anxiety disorders/depression at preschool and school age. Trajectories differed regarding loss/separation experience, maltreatment, maternal psychopathology, temperament, and stress-hormone regulation with loss/separation, temperament, maternal psychopathology, and stress-hormone regulation (trend) significantly contributing to explained variance. At school age, trajectories continued to differ on symptoms, disorders, and impairment. Our study is among the first to show that severe early adversity may trigger a chronic and neurobiologically distinct internalizing trajectory from preschool age onward.

Elastic-Plastic Behaviour of Ultrasonic Assisted Compression of Polyvinyl Chloride (PVC) Foam

Science.gov (United States)

Muhalim, N. A. D.; Hassan, M. Z.; Daud, Y.

2018-04-01

The present study aims to investigate the elastic-plastic behaviour of ultrasonic assisted compression of PVC closed-cell foam. A series of static and ultrasonic compression test of PVC closed-cell foam were conducted at a constant cross head speed of 30 mm/min on dry surface condition. For quasi-static test, specimen was compressed between two rigid platens using universal testing machine. In order to evaluate the specimen behavior under ultrasonic condition, specimen was placed between a specifically design double-slotted block horn and rigid platen. The horn was designed and fabricated prior to the test as a medium to transmit the ultrasonic vibration from the ultrasonic transducer to the working specimen. It was tuned to a frequency of 19.89 kHz in longitudinal mode and provided an average oscillation amplitude at 6 µm on the uppermost surface. Following, the characteristics of stress-strain curves for quasi-static and ultrasonic compression tests were analyzed. It was found that the compressive stress was significantly reduced at the onset of superimposed ultrasonic vibration during plastic deformation.

Impact of thermal stress on evolutionary trajectories of pathogen resistance in three-spined stickleback (Gasterosteus aculeatus).

Science.gov (United States)

Schade, Franziska M; Shama, Lisa N S; Wegner, K Mathias

2014-07-26

Pathogens are a major regulatory force for host populations, especially under stressful conditions. Elevated temperatures may enhance the development of pathogens, increase the number of transmission stages, and can negatively influence host susceptibility depending on host thermal tolerance. As a net result, this can lead to a higher prevalence of epidemics during summer months. These conditions also apply to marine ecosystems, where possible ecological impacts and the population-specific potential for evolutionary responses to changing environments and increasing disease prevalence are, however, less known. Therefore, we investigated the influence of thermal stress on the evolutionary trajectories of disease resistance in three marine populations of three-spined sticklebacks Gasterosteus aculeatus by combining the effects of elevated temperature and infection with a bacterial strain of Vibrio sp. using a common garden experiment. We found that thermal stress had an impact on fish weight and especially on survival after infection after only short periods of thermal acclimation. Environmental stress reduced genetic differentiation (QST) between populations by releasing cryptic within-population variation. While life history traits displayed positive genetic correlations across environments with relatively weak genotype by environment interactions (GxE), environmental stress led to negative genetic correlations across environments in pathogen resistance. This reversal of genetic effects governing resistance is probably attributable to changing environment-dependent virulence mechanisms of the pathogen interacting differently with host genotypes, i.e. GPathogenxGHostxE or (GPathogenxE)x(GHostxE) interactions, rather than to pure host genetic effects, i.e. GHostxE interactions. To cope with climatic changes and the associated increase in pathogen virulence, host species require wide thermal tolerances and pathogen-resistant genotypes. The higher resistance we found

Trajectories of dental anxiety in a birth cohort

Science.gov (United States)

Thomson, W. M.; Broadbent, J. M.; Locker, D.; Poulton, R.

2010-01-01

Objective To examine predictors of dental anxiety trajectories in a longitudinal study of New Zealanders. Methods Prospective study of a complete birth cohort born in 1972/73 in Dunedin, New Zealand, with dental anxiety scale (DAS) scores and dental utilization determined at ages 15, 18, 26 and 32 years. Personality traits were assessed at a superfactor and (more fine-grained) subscale level via the Multidimensional Personality Questionnaire at age 18 years. Group-based trajectory analysis was used to identify dental anxiety trajectories. Results DAS scores from at least three assessments were available for 828 participants. Six dental anxiety trajectories were observed: stable nonanxious low (39.6%); stable nonanxious medium (37.9%); recovery (1.6%); adult-onset anxious (7.7%); stable anxious (7.2%) and adolescent-onset anxious (5.9%). Multivariate analysis showed that males and those with higher DMFS at age 15 years were more likely to be in the stable nonanxious low trajectory group. Membership of the stable nonanxious medium group was predicted by the dental caries experience at age 15 years. Participants who had lost one or more teeth between ages 26 and 32 years had almost twice the relative risk for membership of the adult-onset anxious group. Personality traits predicted group membership. Specifically, high scorers (via median split) on the ‘stress reaction’ subscale had over twice the risk of being in the stable anxious group; low scorers on the traditionalism subscale were more likely to be members of the recovery trajectory group; and high scorers on the ‘social closeness’ subscale had half the risk of being in the stable anxious group. Dental caries experience at age 5 years was also a predictor for the stable anxious group. Membership of the late-adolescent-onset anxious group was predicted by higher dental caries experience by age 15 years, but none of the other predictors was significant. Conclusion Six discrete trajectories of dental anxiety

An experimental study of the effects of bodyside compression on forward swept sidewall compression inlets ingesting a turbulent boundary layer

Science.gov (United States)

Rodi, Patrick E.

1993-01-01

Forward swept sidewall compression inlets have been tested in the Mach 4 Blowdown Facility at the NASA Langley Research Center to study the effects of bodyside compression surfaces on inlet performance in the presence of an incoming turbulent boundary layer. The measurements include mass flow capture and mean surface pressure distributions obtained during simulated combustion pressure increases downstream of the inlet. The kerosene-lampblack surface tracer technique has been used to obtain patterns of the local wall shear stress direction. Inlet performance is evaluated using starting and unstarting characteristics, mass capture, mean surface pressure distributions and permissible back pressure limits. The results indicate that inlet performance can be improved with selected bodyside compression surfaces placed between the inlet sidewalls.

Pregnancy Anxiety and Prenatal Cortisol Trajectories

Science.gov (United States)

Kane, Heidi S.; Schetter, Christine Dunkel; Glynn, Laura M.; Hobel, Calvin J.; Sandman, Curt A.

2014-01-01

Pregnancy anxiety is a potent predictor of adverse birth and infant outcomes. The goal of the current study was to examine one potential mechanism whereby these effects may occur by testing associations between pregnancy anxiety and maternal salivary cortisol on 4 occasions during pregnancy in a sample of 448 women. Higher mean levels of pregnancy anxiety over the course of pregnancy predicted steeper increases in cortisol trajectories compared to lower pregnancy anxiety. Significant differences between cortisol trajectories emerged between 30 to 31 weeks of gestation. Results remained significant when adjusted for state anxiety and perceived stress. Neither changes in pregnancy anxiety over gestation, nor pregnancy anxiety specific to only a particular time in pregnancy predicted cortisol. These findings provide support for one way in which pregnancy anxiety may influence maternal physiology and contribute to a growing literature on the complex biological pathways linking pregnancy anxiety to birth and infant outcomes. PMID:24769094

DNABIT Compress – Genome compression algorithm

Science.gov (United States)

Rajarajeswari, Pothuraju; Apparao, Allam

2011-01-01

Data compression is concerned with how information is organized in data. Efficient storage means removal of redundancy from the data being stored in the DNA molecule. Data compression algorithms remove redundancy and are used to understand biologically important molecules. We present a compression algorithm, “DNABIT Compress” for DNA sequences based on a novel algorithm of assigning binary bits for smaller segments of DNA bases to compress both repetitive and non repetitive DNA sequence. Our proposed algorithm achieves the best compression ratio for DNA sequences for larger genome. Significantly better compression results show that “DNABIT Compress” algorithm is the best among the remaining compression algorithms. While achieving the best compression ratios for DNA sequences (Genomes),our new DNABIT Compress algorithm significantly improves the running time of all previous DNA compression programs. Assigning binary bits (Unique BIT CODE) for (Exact Repeats, Reverse Repeats) fragments of DNA sequence is also a unique concept introduced in this algorithm for the first time in DNA compression. This proposed new algorithm could achieve the best compression ratio as much as 1.58 bits/bases where the existing best methods could not achieve a ratio less than 1.72 bits/bases. PMID:21383923

Vacancy behavior in a compressed fcc Lennard-Jones crystal

International Nuclear Information System (INIS)

Beeler, J.R. Jr.

1981-12-01

This computer experiment study concerns the determination of the stable vacancy configuration in a compressed fcc Lennard-Jones crystal and the migration of this defect in a compressed crystal. Isotropic and uniaxial compression stress conditions were studied. The isotropic and uniaxial compression magnitudes employed were 0.94 less than or equal to eta less than or equal to 1.5, and 1.0 less than or equal to eta less than or equal to 1.5, respectively. The site-centered vacancy (SCV) was the stable vacancy configuration whenever cubic symmetry was present. This includes all of the isotropic compression cases and the particular uniaxial compression case (eta = √2) that give a bcc structure. In addition, the SCV was the stable configuration for uniaxial compression eta 1.20, the SV-OP is an extended defect and, therefore, a saddle point for SV-OP migration could not be determined. The mechanism for the transformation from the SCV to the SV-OP as the stable form at eta = 1.29 appears to be an alternating sign [101] and/or [011] shear process

Stress anisotropy and stress gradient in magnetron sputtered films with different deposition geometries

International Nuclear Information System (INIS)

Zhao, Z.B.; Yalisove, S.M.; Bilello, J.C.

2006-01-01

Mo films were deposited via magnetron sputtering with two different deposition geometries: dynamic deposition (moving substrate) and static deposition (fixed substrate). The residual stress and structural morphologies of these films were investigated, with particular focus on in-plane anisotropy of the biaxial stress and stress gradient across the film thickness. The results revealed that the Mo films developed distinct states of residual stress, which depended on both deposition geometry and film thickness. With the dynamic geometry, the Mo films generally exhibited anisotropic stress. Both the degree of anisotropy and the magnitude of stress varied as functions of film thickness. The variation of stress was linked to the evolution of anisotropic microstructures in the films. The Mo films from the static geometry developed isotropic residual stress, which was more compressive and noticeably larger in magnitude than that of the Mo films from the dynamic geometry. Aside from these disparities, the two types of Mo films (i.e., anisotropic and isotropic) exhibited notably similar trends of stress variation with film thickness. Depth profiling indicated the presence of large stress gradients for the Mo films, irrespective of the deposition geometries. This observation seems to be consistent with the premise that Mo films develop a zone T structure, which is inherently inhomogeneous along the film thickness. Moreover, the largest stress gradient for both types of deposition geometries arises at roughly the same film depth (∼240 nm from substrate), where the stresses sharply transits from highly compressive to less compressive or even tensile. This appears to correspond to the boundary region that separates two distinct stages of microstructural evolution, a feature unique to zone T-type structure

Free compression tube. Applications

Science.gov (United States)

Rusu, Ioan

2012-11-01

During the flight of vehicles, their propulsion energy must overcome gravity, to ensure the displacement of air masses on vehicle trajectory, to cover both energy losses from the friction between a solid surface and the air and also the kinetic energy of reflected air masses due to the impact with the flying vehicle. The flight optimization by increasing speed and reducing fuel consumption has directed research in the aerodynamics field. The flying vehicles shapes obtained through studies in the wind tunnel provide the optimization of the impact with the air masses and the airflow along the vehicle. By energy balance studies for vehicles in flight, the author Ioan Rusu directed his research in reducing the energy lost at vehicle impact with air masses. In this respect as compared to classical solutions for building flight vehicles aerodynamic surfaces which reduce the impact and friction with air masses, Ioan Rusu has invented a device which he named free compression tube for rockets, registered with the State Office for Inventions and Trademarks of Romania, OSIM, deposit f 2011 0352. Mounted in front of flight vehicles it eliminates significantly the impact and friction of air masses with the vehicle solid. The air masses come into contact with the air inside the free compression tube and the air-solid friction is eliminated and replaced by air to air friction.

Stress relaxation in quasi-two-dimensional self-assembled nanoparticle monolayers

Science.gov (United States)

Boucheron, Leandra S.; Stanley, Jacob T.; Dai, Yeling; You, Siheng Sean; Parzyck, Christopher T.; Narayanan, Suresh; Sandy, Alec R.; Jiang, Zhang; Meron, Mati; Lin, Binhua; Shpyrko, Oleg G.

2018-05-01

We experimentally probed the stress relaxation of a monolayer of iron oxide nanoparticles at the water-air interface. Upon drop-casting onto a water surface, the nanoparticles self-assembled into islands of two-dimensional hexagonally close packed crystalline domains surrounded by large voids. When compressed laterally, the voids gradually disappeared as the surface pressure increased. After the compression was stopped, the surface pressure (as measured by a Wilhelmy plate) evolved as a function of the film aging time with three distinct timescales. These aging dynamics were intrinsic to the stressed state built up during the non-equilibrium compression of the film. Utilizing x-ray photon correlation spectroscopy, we measured the characteristic relaxation time (τ ) of in-plane nanoparticle motion as a function of the aging time through both second-order and two-time autocorrelation analysis. Compressed and stretched exponential fitting of the intermediate scattering function yielded exponents (β ) indicating different relaxation mechanisms of the films under different compression stresses. For a monolayer compressed to a lower surface pressure (between 20 mN/m and 30 mN/m), the relaxation time (τ ) decreased continuously as a function of the aging time, as did the fitted exponent, which transitioned from being compressed (>1 ) to stretched (stress release through crystalline domain reorganization. However, for a monolayer compressed to a higher surface pressure (around 40 mN/m), the relaxation time increased continuously and the compressed exponent varied very little from a value of 1.6, suggesting that the system may have been highly stressed and jammed. Despite the interesting stress relaxation signatures seen in these samples, the structural ordering of the monolayer remained the same over the sample lifetime, as revealed by grazing incidence x-ray diffraction.

Mechanics of the Compression Wood Response: II. On the Location, Action, and Distribution of Compression Wood Formation.

Science.gov (United States)

Archer, R R; Wilson, B F

1973-04-01

A new method for simulation of cross-sectional growth provided detailed information on the location of normal wood and compression wood increments in two tilted white pine (Pinus strobus L.) leaders. These data were combined with data on stiffness, slope, and curvature changes over a 16-week period to make the mechanical analysis. The location of compression wood changed from the under side to a flank side and then to the upper side of the leader as the geotropic stimulus decreased, owing to compression wood action. Its location shifted back to a flank side when the direction of movement of the leader reversed. A model for this action, based on elongation strains, was developed and predicted the observed curvature changes with elongation strains of 0.3 to 0.5%, or a maximal compressive stress of 60 to 300 kilograms per square centimeter. After tilting, new wood formation was distributed so as to maintain consistent strain levels along the leaders in bending under gravitational loads. The computed effective elastic moduli were about the same for the two leaders throughout the season.

A Constitutive Model for Unsaturated soils based on a Compressibility Framework dependent on Suction and Degree of Saturation

OpenAIRE

Sitarenios Panagiotis; Kavvadas Michael

2016-01-01

The Modified Cam Clay model is extended to account for the behaviour of unsaturated soils using Bishop’s stress. To describe the Loading – Collapse behaviour, the model incorporates a compressibility framework with suction and degree of saturation dependent compression lines. For simplicity, the present paper describes the model in the triaxial stress space with characteristic simulations of constant suction compression and triaxial tests, as well as wetting tests. The model reproduces an evo...

Dynamic High-Temperature Characterization of an Iridium Alloy in Compression at High Strain Rates

Energy Technology Data Exchange (ETDEWEB)

Song, Bo [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Experimental Environment Simulation Dept.; Nelson, Kevin [Sandia National Lab. (SNL-CA), Livermore, CA (United States). Mechanics of Materials Dept.; Lipinski, Ronald J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Advanced Nuclear Fuel Cycle Technology Dept.; Bignell, John L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Structural and Thermal Analysis Dept.; Ulrich, G. B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Radioisotope Power Systems Program; George, E. P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Radioisotope Power Systems Program

2014-06-01

Iridium alloys have superior strength and ductility at elevated temperatures, making them useful as structural materials for certain high-temperature applications. However, experimental data on their high-temperature high-strain-rate performance are needed for understanding high-speed impacts in severe elevated-temperature environments. Kolsky bars (also called split Hopkinson bars) have been extensively employed for high-strain-rate characterization of materials at room temperature, but it has been challenging to adapt them for the measurement of dynamic properties at high temperatures. Current high-temperature Kolsky compression bar techniques are not capable of obtaining satisfactory high-temperature high-strain-rate stress-strain response of thin iridium specimens investigated in this study. We analyzed the difficulties encountered in high-temperature Kolsky compression bar testing of thin iridium alloy specimens. Appropriate modifications were made to the current high-temperature Kolsky compression bar technique to obtain reliable compressive stress-strain response of an iridium alloy at high strain rates (300 – 10000 s^-1) and temperatures (750°C and 1030°C). Uncertainties in such high-temperature high-strain-rate experiments on thin iridium specimens were also analyzed. The compressive stress-strain response of the iridium alloy showed significant sensitivity to strain rate and temperature.

Compressive properties of silica aerogel at 295, 76, and 20K

International Nuclear Information System (INIS)

Arvidson, J.M.; Scull, L.L.

1986-01-01

Specimens of silica aerogel were tested in compression at 295, 76, and 20 K in a helium gas environment. The properties reported include Young's modulus, the proportional limit, and yield strength. Compressive stress-versus-strain curves at these temperatures are also given. A test apparatus was developed specifically to determine the compressive properties of low strength materials. To measure specimen strain a concentric, overlapping-cylinder, capacitance extensometer was developed. This frictionless device has the capability to conduct variable temperature tests at any temperature from 1.8 to 295 K. Results from the compression tests indicate that at low temperatures the material is not only stronger, but tougher. During 295-K compression tests, the samples fractured and, in some cases, crumbled. After 76- or 20-K compression tests, the specimens remained intact

Compressibility effects in the shear layer over a rectangular cavity

Energy Technology Data Exchange (ETDEWEB)

Beresh, Steven J.; Wagner, Justin; Casper, Katya Marie

2016-10-26

we studied the influence of compressibility on the shear layer over a rectangular cavity of variable width in a free stream Mach number range of 0.6–2.5 using particle image velocimetry data in the streamwise centre plane. As the Mach number increases, the vertical component of the turbulence intensity diminishes modestly in the widest cavity, but the two narrower cavities show a more substantial drop in all three components as well as the turbulent shear stress. Furthermore, this contrasts with canonical free shear layers, which show significant reductions in only the vertical component and the turbulent shear stress due to compressibility. The vorticity thickness of the cavity shear layer grows rapidly as it initially develops, then transitions to a slower growth rate once its instability saturates. When normalized by their estimated incompressible values, the growth rates prior to saturation display the classic compressibility effect of suppression as the convective Mach number rises, in excellent agreement with comparable free shear layer data. The specific trend of the reduction in growth rate due to compressibility is modified by the cavity width.

Behaviour of soil-cement specimens in unconfined dynamic compression

Science.gov (United States)

Davies, J.; Fendukly, L. M.

1994-06-01

The response of the cement-stabilized red marl to dynamic loading in compression has been investigated over a range of cement contents and curing times. Specimens were subjected to different stress levels below unconfined compressive strength, at a frequency of 5 Hz, and a fatigue relationship for the material was developed. The value of resilient modulus was found to be greater than the modulus of elasticity for the same cement content and curing time.

Stress State Analysis and Failure Mechanisms of Masonry Columns Reinforced with FRP under Concentric Compressive Load

Directory of Open Access Journals (Sweden)

Jiří Witzany

2016-04-01

Full Text Available The strengthening and stabilization of damaged compressed masonry columns with composites based on fabrics of high-strength fibers and epoxy resin, or polymer-modified cement mixtures, belongs to novel, partially non-invasive and reversible progressive methods. The stabilizing and reinforcing effect of these fabrics significantly applies to masonry structures under concentric compressive loading whose failure mechanism is characterized by the appearance and development of vertical tensile cracks accompanied by an increase in horizontal masonry strain. During the appearance of micro and hairline cracks (10−3 to 10−1 mm, the effect of non-pre-stressed wrapping composite is very small. The favorable effect of passive wrapping is only intensively manifested after the appearance of cracks (10−1 mm and bigger at higher loading levels. In the case of “optimum” reinforcement of a masonry column, the experimental research showed an increase in vertical displacements δy (up to 247%, horizontal displacements δx (up to 742% and ultimate load-bearing capacity (up to 136% compared to the values reached in unreinforced masonry columns. In the case of masonry structures in which no intensive “bed joint filler–masonry unit” interaction occurs, e.g., in regular coursed masonry with little differences in the mechanical characteristics of masonry units and the binder, the reinforcing effect of the fabric applies only partially.

The impact of mineral composition on compressibility of saturated soils

OpenAIRE

Dolinar, Bojana

2012-01-01

This article analyses the impact of soils` mineral composition on their compressibility. Physical and chemical properties of minerals which influence the quantity of intergrain water in soils and, consequently, the compressibility of soils are established by considering the previous theoretical findings. Test results obtained on artificially prepared samples are used to determine the analytical relationship between the water content and stress state, depending on the mineralogical properties ...

Orion Exploration Flight Test 1 (EFT-1) Best Estimated Trajectory Development

Science.gov (United States)

Holt, Greg N.; Brown, Aaron

2016-01-01

The Orion Exploration Flight Test 1 (EFT-1) mission successfully flew on Dec 5, 2014 atop a Delta IV Heavy launch vehicle. The goal of Orions maiden flight was to stress the system by placing an uncrewed vehicle on a high-energy trajectory replicating conditions similar to those that would be experienced when returning from an asteroid or a lunar mission. The Orion navigation team combined all trajectory data from the mission into a Best Estimated Trajectory (BET) product. There were significant challenges in data reconstruction and many lessons were learned for future missions. The team used an estimation filter incorporating radar tracking, onboard sensors (Global Positioning System and Inertial Measurement Unit), and day-of-flight weather balloons to evaluate the true trajectory flown by Orion. Data was published for the entire Orion EFT-1 flight, plus objects jettisoned during entry such as the Forward Bay Cover. The BET customers include approximately 20 disciplines within Orion who will use the information for evaluating vehicle performance and influencing future design decisions.

Long range trajectories

Energy Technology Data Exchange (ETDEWEB)

Allen, P. W.; Jessup, E. A.; White, R. E. [Air Resources Field Research Office, Las Vegas, Nevada (United States)

1967-07-01

A single air molecule can have a trajectory that can be described with a line, but most meteorologists use single lines to represent the trajectories of air parcels. A single line trajectory has the disadvantage that it is a categorical description of position. Like categorized forecasts it provides no qualification, and no provision for dispersion in case the parcel contains two or more molecules which may take vastly different paths. Diffusion technology has amply demonstrated that an initial aerosol cloud or volume of gas in the atmosphere not only grows larger, but sometimes divides into puffs, each having a different path or swath. Yet, the average meteorologist, faced with the problem of predicting the future motion of a cloud, usually falls back on the line trajectory approach with the explanation that he had no better tool for long range application. In his more rational moments, he may use some arbitrary device to spread his cloud with distance. One such technique has been to separate the trajectory into two or more trajectories, spaced about the endpoint of the original trajectory after a short period of travel, repeating this every so often like a chain reaction. This has the obvious disadvantage of involving a large amount of labor without much assurance of improved accuracy. Another approach is to draw a circle about the trajectory endpoint, to represent either diffusion or error. The problem then is to know what radius to give the circle and also whether to call it diffusion or error. Meteorologists at the Nevada Test Site (NTS) are asked frequently to provide advice which involves trajectory technology, such as prediction of an aerosol cloud path, reconstruction of the motion of a volume of air, indication of the dilution, and the possible trajectory prediction error over great distances. Therefore, we set out, nearly three years ago, to provide some statistical knowledge about the status of our trajectory technology. This report contains some of the

Behavior of quenched and tempered steels under high strain rate compression loading

International Nuclear Information System (INIS)

Meyer, L.W.; Seifert, K.; Abdel-Malek, S.

1997-01-01

Two quenched and tempered steels were tested under compression loading at strain rates of ε = 2.10 2 s -1 and ε = 2.10 3 s -1 . By applying the thermal activation theory, the flow stress at very high strain rates of 10 5 to 10 6 s -1 is derived from low temperature and high strain rate tests. Dynamic true stress - true strain behaviour presents, that stress increases with increasing strain until a maximum, then it decreases. Because of the adiabatic process under dynamic loading the maximum flow stress will occur at a lower strain if the strain rate is increased. Considering strain rate, strain hardening, strain rate hardening and strain softening, a constitutive equation with different additive terms is successfully used to describe the behaviour of material under dynamic compression loading. Results are compared with other models of constitutive equations. (orig.)

Compressive response and deformation mechanisms of vertically aligned helical carbon nanotube forests

Science.gov (United States)

Scheffer, V. C.; Thevamaran, R.; Coluci, V. R.

2018-01-01

We study the dynamic compressive response of vertically aligned helical carbon nanotube forests using a mesoscale model. To describe the compressive response, the model includes the helical geometry of the constituent coils, the entanglement between neighboring coils, and the sideway interactions among coils. Coarse-grained simulations show forest densification and stress localization, which are caused by different deformation mechanisms such as coil packing, buckling, and crushing. We find that these mechanisms depend on the initial overlap between coils and lead to a nonlinear stress-strain behavior that agrees with recent impact experiments. The nonlinear stress-strain behavior was shown to be composed of an initial linear increase of stress in strain followed by an exponential growth. These regimes are an outcome of the characteristics of both the individual coils and the entangled morphology of the forests.

Compressive strength, plastic flow properties, and surface frictional effects of 1100, 3003 and 6061 aluminum alloys

Energy Technology Data Exchange (ETDEWEB)

Pinkerton, Gary Wayne [Univ. of Illinois, Urbana-Champaign, IL (United States)

1993-01-01

The purpose of this study is to find aluminum alloys that are effective for use as wire vacuum seals in the 800MeV particle accelerator located at the Louis Anderson Meson Physics Facility (LAMPF) in Los Alamos, NM. Three alloys, Al 1100, Al 3003, and Al 6061, are investigated under uniaxial compression to determine stresses for a given height reduction from 0 to 70 percent, and to find plastic flow and surface interaction effects. Right-circular cylindrical specimens are compressed on-end (cylindrically) and radially (for modeling as compressed wire). Aluminum 1100 and 3003 alloys are compared for length to diameter ratios of 1 and 2 for both compression types, and are then compared to results of radial compression of annealed small diameter Al 1100 wire currently used at LAMPE. The specimens are also compressed between three different platen surfaces, polished steel, etched steel, and aluminum 6061-T6, to determine effects of friction. The Al 3003 alloy exhibits 20 to 25% lower stresses at all height reductions than Al 1100 for both cylindrical and radial compression.

Compressive strength, plastic flow properties, and surface frictional effects of 1100, 3003 and 6061 aluminum alloys

International Nuclear Information System (INIS)

Pinkerton, G.W.

1993-01-01

The purpose of this study is to find aluminum alloys that are effective for use as wire vacuum seals in the 800MeV particle accelerator located at the Louis Anderson Meson Physics Facility (LAMPF) in Los Alamos, NM. Three alloys, Al 1100, Al 3003, and Al 6061, are investigated under uniaxial compression to determine stresses for a given height reduction from 0 to 70 percent, and to find plastic flow and surface interaction effects. Right-circular cylindrical specimens are compressed on-end (cylindrically) and radially (for modeling as compressed wire). Aluminum 1100 and 3003 alloys are compared for length to diameter ratios of 1 and 2 for both compression types, and are then compared to results of radial compression of annealed small diameter Al 1100 wire currently used at LAMPE. The specimens are also compressed between three different platen surfaces, polished steel, etched steel, and aluminum 6061-T6, to determine effects of friction. The Al 3003 alloy exhibits 20 to 25% lower stresses at all height reductions than Al 1100 for both cylindrical and radial compression

Trajectory Browser Website

Science.gov (United States)

Foster, Cyrus; Jaroux, Belgacem A.

2012-01-01

The Trajectory Browser is a web-based tool developed at the NASA Ames Research Center to be used for the preliminary assessment of trajectories to small-bodies and planets and for providing relevant launch date, time-of-flight and V requirements. The site hosts a database of transfer trajectories from Earth to asteroids and planets for various types of missions such as rendezvous, sample return or flybys. A search engine allows the user to find trajectories meeting desired constraints on the launch window, mission duration and delta V capability, while a trajectory viewer tool allows the visualization of the heliocentric trajectory and the detailed mission itinerary. The anticipated user base of this tool consists primarily of scientists and engineers designing interplanetary missions in the context of pre-phase A studies, particularly for performing accessibility surveys to large populations of small-bodies. The educational potential of the website is also recognized for academia and the public with regards to trajectory design, a field that has generally been poorly understood by the public. The website is currently hosted on NASA-internal URL http://trajbrowser.arc.nasa.gov/ with plans for a public release as soon as development is complete.

Superposition of Stress Fields in Diametrically Compressed Cylinders

Directory of Open Access Journals (Sweden)

João Augusto de Lima Rocha

Full Text Available Abstract The theoretical analysis for the Brazilian test is a classical plane stress problem of elasticity theory, where a vertical force is applied to a horizontal plane, the boundary of a semi-infinite medium. Hypothesizing a normal radial stress field, the results of that model are correct. Nevertheless, the superposition of three stress fields, with two being based on prior results and the third based on a hydrostatic stress field, is incorrect. Indeed, this work shows that the Cauchy vectors (tractions are non-vanishing in the parallel planes in which the two opposing vertical forces are applied. The aim of this work is to detail the process used in the construction of the theoretical model for the three stress fields used, with the objective being to demonstrate the inconsistency often stated in the literature.

Dislocations and point defects in hydrostatically compressed crystal

International Nuclear Information System (INIS)

Kosevich, A.M.; Tokij, V.V.; Strel'tsov, V.A.

1978-01-01

Within the framework of the theory of finite deformations, the elastic fields are considered, which are induced by the sources of internal stresses in a crystal compressed under a high pressure. In the case of a hydrostatically compressed crystal with defects, the use of a variation principle is discussed. Using the smallness of distorsions, the linear theory of elastic fields of defects in the crystal compressed under a high pressure, is developed. An analysis of the main relationships of the theory results in the following conclusion: in a course of the linear approximation the taking into account of the hydrostatic pressure brings to the renorming of the elasticity moduli and to the replacing of the hydrostatic parameters of defects by their values in the compressed crystal. That conclusion allows the results of the elasticity linear theory of the crystal with defects to be used to the full extent

influence of relative humidity on tensile and compressive creep

African Journals Online (AJOL)

HOD

creep specimens were cured in a fog room at 99% RH and 20 oC until the beginning of the tests in the controlled environment creep rooms. To eliminate the influence of stress level and age of loading, a uniform stress of 12.26MPa was used for the three compressive creep tests and the specimens were all loaded at the.

Mesoscopic analyses of porous concrete under static compression and drop weight impact tests

DEFF Research Database (Denmark)

Agar Ozbek, A.S.; Pedersen, R.R.; Weerheijm, J.

2008-01-01

was considered as a four-phase material incorporating aggregates, bulk cement paste, interfacial transition zones and meso-size air pores. The stress-displacement relations obtained from static compression tests, the stress values, and the corresponding damage levels provided by the drop weight impact tests were......The failure process in highly porous concrete was analyzed experimentally and numerically. A triaxial visco-plastic damage model and a mesoscale representation of the material composition were considered to reproduce static compression and drop weight impact tests. In the mesoscopic model, concrete...

Shock compression and quasielastic release in tantalum

International Nuclear Information System (INIS)

Johnson, J.N.; Hixson, R.S.; Tonks, D.L.; Gray, G.T. III

1994-01-01

Previous studies of quasielastic release in shock-loaded FCC metals have shown a strong influence of the defect state on the leading edge, or first observable arrival, of the release wave. This is due to the large density of pinned dislocation segments behind the shock front, their relatively large pinning separation, and a very short response time as determined by the drag coefficient in the shock-compressed state. This effect is entirely equivalent to problems associated with elastic moduli determination using ultrasonic methods. This is particularly true for FCC metals, which have an especially low Peierls stress, or inherent lattice resistance, that has little influence in pinning dislocation segments and inhibiting anelastic deformation. BCC metals, on the other hand, have a large Peierls stress that essentially holds dislocation segments in place at low net applied shear stresses and thus allows fully elastic deformation to occur in the complete absence of anelastic behavior. Shock-compression and release experiments have been performed on tantalum (BCC), with the observation that the leading release disturbance is indeed elastic. This conclusion is established by examination of experimental VISAR records taken at the tantalum/sapphire (window) interface in a symmetric-impact experiment which subjects the sample to a peak longitudinal stress of approximately 7.3 GPa, in comparison with characteristic code calculations. copyright 1994 American Institute of Physics

Three-dimensional numerical simulation for plastic injection-compression molding

Science.gov (United States)

Zhang, Yun; Yu, Wenjie; Liang, Junjie; Lang, Jianlin; Li, Dequn

2018-03-01

Compared with conventional injection molding, injection-compression molding can mold optical parts with higher precision and lower flow residual stress. However, the melt flow process in a closed cavity becomes more complex because of the moving cavity boundary during compression and the nonlinear problems caused by non-Newtonian polymer melt. In this study, a 3D simulation method was developed for injection-compression molding. In this method, arbitrary Lagrangian- Eulerian was introduced to model the moving-boundary flow problem in the compression stage. The non-Newtonian characteristics and compressibility of the polymer melt were considered. The melt flow and pressure distribution in the cavity were investigated by using the proposed simulation method and compared with those of injection molding. Results reveal that the fountain flow effect becomes significant when the cavity thickness increases during compression. The back flow also plays an important role in the flow pattern and redistribution of cavity pressure. The discrepancy in pressures at different points along the flow path is complicated rather than monotonically decreased in injection molding.

Evaluation of residual stress in sputtered tantalum thin-film

Energy Technology Data Exchange (ETDEWEB)

Al-masha’al, Asa’ad, E-mail: asaad.al@ed.ac.uk; Bunting, Andrew; Cheung, Rebecca

2016-05-15

Highlights: • Tantalum thin-films have been deposited by DC magnetron sputtering system. • Thin-film stress is observed to be strongly influenced by sputtering pressure. • Transition towards the compressive stress is ascribed to the annealing at 300 °C. • Expose thin-film to air ambient or ion bombardment lead to a noticeable change in the residual stress. - Abstract: The influence of deposition conditions on the residual stress of sputtered tantalum thin-film has been evaluated in the present study. Films have been deposited by DC magnetron sputtering and curvature measurement method has been employed to calculate the residual stress of the films. Transitions of tantalum film stress from compressive to tensile state have been observed as the sputtering pressure increases. Also, the effect of annealing process at temperature range of 90–300 °C in oxygen ambient on the residual stress of the films has been studied. The results demonstrate that the residual stress of the films that have been deposited at lower sputtering pressure has become more compressive when annealed at 300 °C. Furthermore, the impact of exposure to atmospheric ambient on the tantalum film stress has been investigated by monitoring the variation of the residual stress of both annealed and unannealed films over time. The as-deposited films have been exposed to pure Argon energy bombardment and as result, a high compressive stress has been developed in the films.

Stress in hard metal films

NARCIS (Netherlands)

Janssen, G.C.A.M.; Kamminga, J.D.

2004-01-01

In the absence of thermal stress, tensile stress in hard metal films is caused by grain boundary shrinkage and compressive stress is caused by ion peening. It is shown that the two contributions are additive. Moreover tensile stress generated at the grain boundaries does not relax by ion

Management by Trajectory: Trajectory Management Study Report

Science.gov (United States)

Leiden, Kenneth; Atkins, Stephen; Fernandes, Alicia D.; Kaler, Curt; Bell, Alan; Kilbourne, Todd; Evans, Mark

2017-01-01

In order to realize the full potential of the Next Generation Air Transportation System (NextGen), improved management along planned trajectories between air navigation service providers (ANSPs) and system users (e.g., pilots and airline dispatchers) is needed. Future automation improvements and increased data communications between aircraft and ground automation would make the concept of Management by Trajectory (MBT) possible.

Biaxial failure criteria and stress-strain response for concrete of containment structure

International Nuclear Information System (INIS)

Lee, S. K.; Woo, S. K.; Song, Y. C.; Kweon, Y. K.; Cho, C. H.

2001-01-01

Biaxial failure criteria and stress-strain response for plain concrete of containment structure on nuclear power plants are studied under uniaxial and biaxial stress(compression-compression, compression-tension, and tension-tension combined stress). The concrete specimens of a square plate type are used for uniaxial and biaxial loading. The experimental data indicate that the strength of concrete under biaxial compression, f 2 /f 1 =-1/-1, is 17 percent larger than under uniaxial compression and the poisson's ratio of concrete is 0.1745. On the base of the results, a biaxial failure envelope for plain concrete that the uniaxial strength is 5660 psi are provided, and the biaxial failure behaviors for three biaxial loading areas are plotted respectively. And, various analytical equations having the reliability are proposed for representations of the biaxial failure criteria and stress-strain response curves of concrete

Influence of Ni Solute segregation on the intrinsic growth stresses in Cu(Ni) thin films

International Nuclear Information System (INIS)

Kaub, T.M.; Felfer, P.; Cairney, J.M.; Thompson, G.B.

2016-01-01

Using intrinsic solute segregation in alloys, the compressive stress in a series of Cu(Ni) thin films has been studied. The highest compressive stress was noted in the 5 at.% Ni alloy, with increasing Ni concentration resulting in a subsequent reduction of stress. Atom probe tomography quantified Ni's Gibbsian interfacial excess in the grain boundaries and confirmed that once grain boundary saturation is achieved, the compressive stress was reduced. This letter provides experimental support in elucidating how interfacial segregation of excess adatoms contributes to the post-coalescence compressive stress generation mechanism in thin films. - Graphical abstract: Cu(Ni) film stress relationship with Ni additions. Atom probe characterization confirms solute enrichment in the boundaries, which was linked to stress response.

Comparison of the compressive yield response of aggregated suspensions: Pressure filtration, centrifugation, and osmotic consolidation

International Nuclear Information System (INIS)

Miller, K.T.; Melant, R.M.; Zukoski, C.F.

1996-01-01

The compressive rheological responses of suspensions containing flocculated kaolin, alumina (average particle sizes of 0.2 and 0.5 microm), and hydrous zirconia (average particle sizes of 8, 57, and 139 nm) particles have been measured using three different techniques: pressure filtration, volume fraction profile during centrifugation, and sediment height during centrifugation at multiple spinning speeds. While the volume fraction profile technique appears to be experimentally most robust, equivalent responses are found using the different techniques, indicating that the compressive yield stress is a material property of a given suspension. The compressive yield stress of each suspension increases rapidly with volume fraction but cannot be generally described using simple power-law or exponential fits. The compressive yield stress also increases with the inverse square of particle size. The packing behavior of the suspensions undergoing osmotic consolidation is compared with the mechanical compressive yield response. Some suspensions exhibited the same packing behavior as in the mechanical techniques, while others consistently packed to higher densities during osmotic consolidation. Although equivalent osmotic and mechanical loads do not always result in the same volume fractions, the similar increases in volume fraction with applied driving force suggest that both the osmotic and mechanical techniques are controlled by the force needed to rearrange the particle network

Channeling of protons in various types of radially compressed carbon nanotubes

International Nuclear Information System (INIS)

Karabarbounis, A.; Sarros, S.; Trikalinos, Ch.

2015-01-01

Channeling of 10 MeV protons in various types of radially compressed chiral carbon nanotubes is considered. Monte Carlo simulation program is used for the calculation of the trajectories, energy losses and angular distributions of protons in nanotubes of various lengths, where the potential in Doyle–Turner approximation is used to describe the interaction between a proton and a nanotube. Carbon nanotubes, which are considered, are radially compressed at the centre or at both ends. The results show that in some cases a decreased angular distribution of the beam is observed, compared with propagation through a straight nanotube. Furthermore, the energy distribution of channeled protons in nanotubes present a series of small peaks besides a main one, the number of which depends on the nanotube length and the angle of incidence, which in some cases are significantly high

Channeling of protons in various types of radially compressed carbon nanotubes

Energy Technology Data Exchange (ETDEWEB)

Karabarbounis, A. [Department of Physics, Section of Nuclear and Particle Physics, University of Athens, Panepistimioupolis, Ilissia, 15771 Athens (Greece); Sarros, S., E-mail: stsarros@phys.uoa.gr [Department of Physics, Section of Nuclear and Particle Physics, University of Athens, Panepistimioupolis, Ilissia, 15771 Athens (Greece); Trikalinos, Ch. [Department of Philosophy and History of Science, University of Athens, Panepistimioupolis, Ilissia, 15771 Athens (Greece)

2015-07-15

Channeling of 10 MeV protons in various types of radially compressed chiral carbon nanotubes is considered. Monte Carlo simulation program is used for the calculation of the trajectories, energy losses and angular distributions of protons in nanotubes of various lengths, where the potential in Doyle–Turner approximation is used to describe the interaction between a proton and a nanotube. Carbon nanotubes, which are considered, are radially compressed at the centre or at both ends. The results show that in some cases a decreased angular distribution of the beam is observed, compared with propagation through a straight nanotube. Furthermore, the energy distribution of channeled protons in nanotubes present a series of small peaks besides a main one, the number of which depends on the nanotube length and the angle of incidence, which in some cases are significantly high.

Laser quench hardening of steel: Effects of superimposed elastic pre-stress on the hardness and residual stress distribution

Science.gov (United States)

Meserve, Justin

Cold drawn AISI 4140 beams were LASER surface hardened with a 2 kW CO2 LASER. Specimens were treated in the free state and while restrained in a bending fixture inducing surface tensile stresses of 94 and 230 MPa. Knoop hardness indentation was used to evaluate the through thickness hardness distribution, and a layer removal methodology was used to evaluate the residual stress distribution. Results showed the maximum surface hardness attained was not affected by pre-stress during hardening, and ranged from 513 to 676 kg/mm2. The depth of effective hardening varied at different magnitudes of pre-stress, but did not vary proportionately to the pre-stress. The surface residual stress, coinciding with the maximum compressive residual stress, increased as pre-stress was increased, from 1040 MPa for the nominally treated specimens to 1270 MPa for specimens pre-stressed to 230 MPa. The maximum tensile residual stress observed in the specimens decreased from 1060 MPa in the nominally treated specimens to 760 MPa for specimens pre-stressed to 230 MPa. Similarly, thickness of the compressive residual stress region increased and the depth at which maximum tensile residual stress occurred increased as the pre-stress during treatment was increased Overall, application of tensile elastic pre-stress during LASER hardening is beneficial to the development of compressive residual stress in AISI 4140, with minimal impact to the hardness attained from the treatment. The newly developed approach for LASER hardening may support efforts to increase both the wear and fatigue resistance of parts made from hardenable steels.

Internal stress control of boron thin film

Energy Technology Data Exchange (ETDEWEB)

Satomi, N.; Kitamura, M.; Sasaki, T.; Nishikawa, M. [Osaka Univ., Suita (Japan). Graduate Sch. of Eng.

1998-09-01

The occurrence of stress in thin films has led to serious stability problems in practical use. We have investigated the stress in the boron films to find the deposition condition of the boron films with less stress. It was found that the stress in the boron film varies sufficiently from compressive to tensile stress, that is from -1.0 to 1.4 GPa, depending on the evaporation conditions, such as deposition rate and the substrate temperature. Hydrogen ion bombardment resulted in the enhancement of the compressive stress, possibly due to ion peening effect, while under helium ion bombardment, stress relief was observed. The boron film with nearly zero stress was obtained by the evaporation at a deposition rate of 0.5 nm s{sup -1} and substrate temperature of 300 C. (orig.) 12 refs.

Internal stress control of boron thin film

International Nuclear Information System (INIS)

Satomi, N.; Kitamura, M.; Sasaki, T.; Nishikawa, M.

1998-01-01

The occurrence of stress in thin films has led to serious stability problems in practical use. We have investigated the stress in the boron films to find the deposition condition of the boron films with less stress. It was found that the stress in the boron film varies sufficiently from compressive to tensile stress, that is from -1.0 to 1.4 GPa, depending on the evaporation conditions, such as deposition rate and the substrate temperature. Hydrogen ion bombardment resulted in the enhancement of the compressive stress, possibly due to ion peening effect, while under helium ion bombardment, stress relief was observed. The boron film with nearly zero stress was obtained by the evaporation at a deposition rate of 0.5 nm s -1 and substrate temperature of 300 C. (orig.)

Thermal effect on gravity waves in a compressible liquid layer over a ...

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

Abstract. This paper deals with the effect of temperature on gravity waves in a compressible liquid layer over a solid half-space. It has been assumed that the liquid layer is under the action of gravity, while the solid half-space is under the influence of initial compressive hydrostatic stress. When the temperature of the.

Dynamic compressive response of wrought and additive manufactured 304L stainless steels

Directory of Open Access Journals (Sweden)

Nishida Erik

2015-01-01

Full Text Available Additive manufacturing (AM technology has been developed to fabricate metal components that include complex prototype fabrication, small lot production, precision repair or feature addition, and tooling. However, the mechanical response of the AM materials is a concern to meet requirements for specific applications. Differences between AM materials as compared to wrought materials might be expected, due to possible differences in porosity (voids, grain size, and residual stress levels. When the AM materials are designed for impact applications, the dynamic mechanical properties in both compression and tension need to be fully characterized and understood for reliable designs. In this study, a 304L stainless steel was manufactured with AM technology. For comparison purposes, both the AM and wrought 304L stainless steels were dynamically characterized in compression Kolsky bar techniques. They dynamic compressive stress-strain curves were obtained and the strain rate effects were determined for both the AM and wrought 304L stainless steels. A comprehensive comparison of dynamic compressive response between the AM and wrought 304L stainless steels was performed. SAND2015-0993 C.

Material Compressing Test of the High Polymer Part Used in Draft Gear of Heavy Load Locomotive

Directory of Open Access Journals (Sweden)

Wei Yangang

2016-01-01

Full Text Available According to the actual load cases of heavy load locomotive, the material compressing tests of the high polymer parts used in the locomotive are researched. The relationship between stress and strain during the material compressing are acquired by means of comparing the many results of the material compressing tests under different test condition. The relationship between stress and strain during the material compressing is nonlinear in large range of strain, but the relationship is approximately linear in small range of strain. The material of the high polymer made in China and the material of the high polymer imported are compared through the tests. The results show that the compressing property of the material of the high polymer made in China and the material of the high polymer imported are almost same. The research offers the foundation to study the structure elasticity of the draft gear.

Biomechanical effects of spinal cord compression due to ossification of posterior longitudinal ligament and ligamentum flavum: a finite element analysis.

Science.gov (United States)

Kim, Yoon Hyuk; Khuyagbaatar, Batbayar; Kim, Kyungsoo

2013-09-01

Ossification of the posterior longitudinal ligament (OPLL) and ossification of the ligamentum flavum (OLF) have been recognized as causes of myelopathy due to thickening of the ligaments resulting in narrowing of the spinal canal and compression of the spinal cord. However, few studies have focused on predicting stress distribution under conditions of OPLL and OLF based on clinical aspects such as the relationship between level of stress and severity of neurologic symptoms because direct in vivo measurement of stress is very restrictive. In this study, a three-dimensional finite element model of the spinal cord in T12-L1 was developed based on MR images. The von-Mises stresses in the cord and the cross-sectional area of the cord were investigated for various grades and shapes of spinal cord compression in OPLL and OLF. Substantial increases in maximum stresses resulting in the manifestation of spinal cord symptoms occurred when the cross-sectional area was reduced by 30-40% at 60% compression of the antero-posterior diameter of the cord in OPLL and at 4mm compression in OLF. These results indicate that compression greater than these thresholds may induce spinal symptoms, which is consistent with clinical observations. Copyright © 2013 IPEM. Published by Elsevier Ltd. All rights reserved.

Interactions between the phase stress and the grain-orientation-dependent stress in duplex stainless steel during deformation

International Nuclear Information System (INIS)

Jia, N.; Peng, R. Lin; Wang, Y.D.; Chai, G.C.; Johansson, S.; Wang, G.; Liaw, P.K.

2006-01-01

The development of phase stress and grain-orientation-dependent stress under uniaxial compression was investigated in a duplex stainless steel consisting of austenite and ferrite. Using in situ neutron diffraction measurements, the strain response of several h k l planes to the applied compressive stress was mapped as a function of applied stress and sample direction. Analysis based on the experimental results and elastoplastic self-consistent simulations shows that phase stresses of thermal origin further increase during elastic loading but decrease with increased plastic deformation. Grain-orientation-dependent stresses become significant in both austenite and ferrite after loading into the plastic region. After unloading from the plastic regime, a considerable intergranular stress remains in the austenitic phase and dominates over the phase stress. This study provides fundamental experimental inputs for future micromechanical modeling aiming at the evaluation and prediction of the mechanical performance of multiphase materials

Trajectories of martian habitability.

Science.gov (United States)

Cockell, Charles S

2014-02-01

Beginning from two plausible starting points-an uninhabited or inhabited Mars-this paper discusses the possible trajectories of martian habitability over time. On an uninhabited Mars, the trajectories follow paths determined by the abundance of uninhabitable environments and uninhabited habitats. On an inhabited Mars, the addition of a third environment type, inhabited habitats, results in other trajectories, including ones where the planet remains inhabited today or others where planetary-scale life extinction occurs. By identifying different trajectories of habitability, corresponding hypotheses can be described that allow for the various trajectories to be disentangled and ultimately a determination of which trajectory Mars has taken and the changing relative abundance of its constituent environments.

Thermal effect on gravity waves in a compressible liquid layer over a ...

Indian Academy of Sciences (India)

This paper deals with the effect of temperature on gravity waves in a compressible liquid layer over a solid half-space. It has been assumed that the liquid layer is under the action of gravity, while the solid half-space is under the influence of initial compressive hydrostatic stress. When the temperature of the half-space is ...

Process and application of shock compression by nanosecond pulses of frequency-doubled Nd:YAG laser

Science.gov (United States)

Sano, Yuji; Kimura, Motohiko; Mukai, Naruhiko; Yoda, Masaki; Obata, Minoru; Ogisu, Tatsuki

2000-02-01

The authors have developed a new process of laser-induced shock compression to introduce a residual compressive stress on material surface, which is effective for prevention of stress corrosion cracking (SCC) and enhancement of fatigue strength of metal materials. The process developed is unique and beneficial. It requires no pre-conditioning for the surface, whereas the conventional process requires that the so-called sacrificial layer is made to protect the surface from damage. The new process can be freely applied to water- immersed components, since it uses water-penetrable green light of a frequency-doubled Nd:YAG laser. The process developed has the potential to open up new high-power laser applications in manufacturing and maintenance technologies. The laser-induced shock compression process (LSP) can be used to improve a residual stress field from tensile to compressive. In order to understand the physics and optimize the process, the propagation of a shock wave generated by the impulse of laser irradiation and the dynamic response of the material were analyzed by time-dependent elasto-plastic calculations with a finite element program using laser-induced plasma pressure as an external load. The analysis shows that a permanent strain and a residual compressive stress remain after the passage of the shock wave with amplitude exceeding the yield strength of the material. A practical system materializing the LSP was designed, manufactured, and tested to confirm the applicability to core components of light water reactors (LWRs). The system accesses the target component and remotely irradiates laser pulses to the heat affected zone (HAZ) along weld lines. Various functional tests were conducted using a full-scale mockup facility, in which remote maintenance work in a reactor vessel could be simulated. The results showed that the system remotely accessed the target weld lines and successfully introduced a residual compressive stress. After sufficient training

Use of compressed-air storage systems; Einsatz von Druckluftspeichersystemen

Energy Technology Data Exchange (ETDEWEB)

Cyphely, I.; Rufer, A.; Brueckmann, Ph.; Menhardt, W.; Reller, A.

2004-07-01

This final report issued by the Swiss Federal Office of Energy (SFOE) looks at the use of compressed air as a means of storing energy. Historical aspects are listed and compressed-air storage as an alternative to current ideas that use electrolysis and hydrogen storage is discussed. The storage efficiency advantages of compressed-air storage is stressed and the possibilities it offers for compensating the stochastic nature of electricity production from renewable energy sources are discussed. The so-called BOP (Battery with Oil-hydraulics and Pneumatics) principle for the storage of electricity is discussed and its function is described. The advantages offered by such a system are listed and the development focus necessary is discussed.

Predictors of Psychological Distress Trajectories in the First Year After a Breast Cancer Diagnosis

Directory of Open Access Journals (Sweden)

Jin-Hee Park, RN, Ph.D.

2017-12-01

Full Text Available Purpose: Psychological distress is a significant and ongoing problem for breast cancer. These mental health problems are often neglected as they are not always properly understood. This study was performed to explore the trajectory of psychological distress over 1 year since breast cancer surgery and to identify the associated factors for the trajectory. Methods: One hundred seventeen women who underwent surgery for breast cancer completed the psychological distress thermometer and problem lists from after surgery to 12 months after surgery. Information on their sociodemographic and clinical characteristics was also obtained. Group-based trajectory modeling was performed to identify the distinct trajectories of psychological distress. Chi-square test and logistic regression analysis were performed to determine predictors of psychological distress trajectories. Results: A two-group linear trajectory model was optimal for modeling psychological distress (Bayesian information criterion = −777.41. Group-based trajectory modeling identified consistently high-distress (19.4% and low-decreasing distress (80.6% trajectories. Old age, depression, nervousness, and pain were significant predictors of consistently high-distress trajectory. Conclusion: Our results indicate that distinct trajectory groups can be used as a screening tool to identify patients who may be at an increased risk of psychological distress over time. Screening for psychological distress during disease diagnosis is important and necessary to identify patients who are at an increased risk of elevated distress or at risk of experiencing psychological distress over time. Keywords: anxiety, breast neoplasms, depression, pain, psychological stress

A novel full-field experimental method to measure the local compressibility of gas diffusion media

Energy Technology Data Exchange (ETDEWEB)

Lai, Yeh-Hung; Li, Yongqiang [Electrochemical Energy Research Lab, GM R and D, Honeoye Falls, NY 14472 (United States); Rock, Jeffrey A. [GM Powertrain, Honeoye Falls, NY 14472 (United States)

2010-05-15

The gas diffusion medium (GDM) in a proton exchange membrane (PEM) fuel cell needs to simultaneously satisfy the requirements of transporting reactant gases, removing product water, conducting electrons and heat, and providing mechanical support to the membrane electrode assembly (MEA). Concerning the localized over-compression which may force carbon fibers and other conductive debris into the membrane to cause fuel cell failure by electronically shorting through the membrane, we have developed a novel full-field experimental method to measure the local thickness and compressibility of GDM. Applying a uniform air pressure upon a thin polyimide film bonded on the top surface of the GDM with support from the bottom by a flat metal substrate and measuring the thickness change using the 3-D digital image correlation technique with an out-of-plane displacement resolution less than 0.5 {mu}m, we have determined the local thickness and compressive stress/strain behavior in the GDM. Using the local thickness and compressibility data over an area of 11.2 mm x 11.2 mm, we numerically construct the nominal compressive response of a commercial Toray trademark TGP-H-060 based GDM subjected to compression by flat platens. Good agreement in the nominal stress/strain curves from the numerical construction and direct experimental flat-platen measurement confirms the validity of the methodology proposed in this article. The result shows that a nominal pressure of 1.4 MPa compressed between two flat platens can introduce localized compressive stress concentration of more than 3 MPa in up to 1% of the total area at various locations from several hundred micrometers to 1 mm in diameter. We believe that this full-field experimental method can be useful in GDM material and process development to reduce the local hard spots and help to mitigate the membrane shorting failure in PEM fuel cells. (author)

A novel full-field experimental method to measure the local compressibility of gas diffusion media

Science.gov (United States)

Lai, Yeh-Hung; Li, Yongqiang; Rock, Jeffrey A.

The gas diffusion medium (GDM) in a proton exchange membrane (PEM) fuel cell needs to simultaneously satisfy the requirements of transporting reactant gases, removing product water, conducting electrons and heat, and providing mechanical support to the membrane electrode assembly (MEA). Concerning the localized over-compression which may force carbon fibers and other conductive debris into the membrane to cause fuel cell failure by electronically shorting through the membrane, we have developed a novel full-field experimental method to measure the local thickness and compressibility of GDM. Applying a uniform air pressure upon a thin polyimide film bonded on the top surface of the GDM with support from the bottom by a flat metal substrate and measuring the thickness change using the 3-D digital image correlation technique with an out-of-plane displacement resolution less than 0.5 μm, we have determined the local thickness and compressive stress/strain behavior in the GDM. Using the local thickness and compressibility data over an area of 11.2 mm × 11.2 mm, we numerically construct the nominal compressive response of a commercial Toray™ TGP-H-060 based GDM subjected to compression by flat platens. Good agreement in the nominal stress/strain curves from the numerical construction and direct experimental flat-platen measurement confirms the validity of the methodology proposed in this article. The result shows that a nominal pressure of 1.4 MPa compressed between two flat platens can introduce localized compressive stress concentration of more than 3 MPa in up to 1% of the total area at various locations from several hundred micrometers to 1 mm in diameter. We believe that this full-field experimental method can be useful in GDM material and process development to reduce the local hard spots and help to mitigate the membrane shorting failure in PEM fuel cells.

Compressive creep of silicon nitride

International Nuclear Information System (INIS)

Silva, C.R.M. da; Melo, F.C.L. de; Cairo, C.A.; Piorino Neto, F.

1990-01-01

Silicon nitride samples were formed by pressureless sintering process, using neodymium oxide and a mixture of neodymium oxide and yttrio oxide as sintering aids. The short term compressive creep behaviour was evaluated over a stress range of 50-300 MPa and temperature range 1200 - 1350 0 C. Post-sintering heat treatments in nitrogen with a stepwise decremental variation of temperature were performed in some samples and microstructural analysis by X-ray diffraction and transmission electron microscopy showed that the secondary crystalline phase which form from the remnant glass are dependent upon composition and percentage of aditives. Stress exponent values near to unity were obtained for materials with low glass content suggesting grain boundary diffusion accommodation processes. Cavitation will thereby become prevalent with increase in stress, temperature and decrease in the degree of crystallization of the grain boundary phase. (author) [pt

The role of locus of control and coping style in predicting longitudinal PTSD-trajectories after combat exposure.

Science.gov (United States)

Karstoft, Karen-Inge; Armour, Cherie; Elklit, Ask; Solomon, Zahava

2015-05-01

While longitudinal posttraumatic stress responses are known to be heterogeneous, little is known about predictors of those responses. We investigated if locus of control (LOC) and coping style are associated with long-term PTSD-trajectories after exposure to combat. Six hundred and seventy five Israeli soldiers with or without combat stress reaction (CSR) from the Lebanon war were assessed 1, 2, and 20 years after the war. Combat exposure, LOC, and coping style were then investigated as covariates of the trajectories of resilience, recovery, delayed onset, and chronicity. Symptomatic trajectories in the CSR and the non-CSR group were significantly associated to varying degrees with perceived life threat during combat (ORs: 1.76-2.53), internal LOC (0.77-0.87), emotional coping style (0.28-0.34), and low use of problem-focused coping (2.12-3.11). In conclusion, assessment of LOC and coping can aid prediction of chronic PTSD outcomes of combat exposure. Copyright © 2015 Elsevier Ltd. All rights reserved.

Usefulness of injecting local anesthetic before compression in stereotactic vacuum-assisted breast biopsy

International Nuclear Information System (INIS)

Matsuura, Akiko; Urashima, Masaki; Nishihara, Reisuke

2009-01-01

Stereotactic vacuum-assisted breast biopsy is a useful method of breast biopsy. However, some patients feel unbearable breast pain due to compression. Breast pain due to compression caused the fact that the breast cannot be compressed sufficiently. Sufficient compression is important to fix the breast in this method. Breast pain during this procedure is problematic from the perspectives of both stress and fixing the breast. We performed biopsy in the original manner by injecting local anesthetic before compression, in order to relieve breast pain due to compression. This was only slightly different in order from the standard method, and there was no need for any special technique or device. This way allowed for even higher breast compression, and all of the most recent 30 cases were compressed at levels greater than 120N. This approach is useful not only for relieving pain, but also for fixing the breast. (author)

Lattice strains in gold and rhenium under nonhydrostatic compression to 37 GPa

International Nuclear Information System (INIS)

Duffy, Thomas S.; Shen, Guoyin; Heinz, Dion L.; Shu, Jinfu; Ma, Yanzhang; Mao, Ho-Kwang; Hemley, Russell J.; Singh, Anil K.

1999-01-01

Using energy-dispersive x-ray diffraction techniques together with the theory describing lattice strains under nonhydrostatic compression, the behavior of a layered sample of gold and rhenium has been studied at pressures of 14-37 GPa. For gold, the uniaxial stress component t is consistent with earlier studies and can be described by t=0.06+0.015P where P is the pressure in GPa. The estimated single-crystal elastic moduli are in reasonable agreement with trends based on extrapolated low-pressure data. The degree of elastic anisotropy increases as α, the parameter which characterizes stress-strain continuity across grain boundaries, is reduced from 1.0 to 0.5. For rhenium, the apparent equation of state has been shown to be strongly influenced by nonhydrostatic compression, as evidenced by its dependence on the angle ψ between the diffracting plane normal and the stress axis. The bulk modulus obtained by inversion of nonhydrostatic compression data can differ by nearly a factor of 2 at angles of 0 degree sign and 90 degree sign . On the other hand, by a proper choice of ψ, d spacings corresponding to quasihydrostatic compression can be obtained from data obtained under highly nonhydrostatic conditions. The uniaxial stress in rhenium over the pressure range from 14-37 GPa can be described by t=2.5+0.09P. The large discrepancy between x-ray elastic moduli and ultrasonic data and theoretical calculations indicates that additional factors such as texturing or orientation dependence of t need to be incorporated to more fully describe the strain distribution in hexagonal-close-packed metals. (c) 1999 The American Physical Society

Overview of the testing activities on ITER sub-scale pre-compression rings

Energy Technology Data Exchange (ETDEWEB)

Rossi, Paolo, E-mail: paolo.rossi@enea.it [Associazione EURATOM-ENEA sulla Fusione, C.R. Frascati, C.P. 65, 00044 Frascati, Rome (Italy); Capobianchi, Mario; Crescenzi, Fabio; Massimi, Alberto; Mugnaini, Giampiero; Pizzuto, Aldo [Associazione EURATOM-ENEA sulla Fusione, C.R. Frascati, C.P. 65, 00044 Frascati, Rome (Italy); Knaster, Juan [ITER Organisation, Route de Vinon sur Verdon, 13115, St. Paul lez Durance (France); Rajainmaki, Hannu [FUSION FOR ENERGY, Josep Pla no. 2, Torres Diagonal Litoral Edificio B3, 08019 Barcelona (Spain)

2012-08-15

Highlights: Black-Right-Pointing-Pointer ENEA developed a high strength glass fiber-epoxy composite for ITER pre-compression rings. Black-Right-Pointing-Pointer High UTS values were obtained at RT on linear specimens (2200 MPa) and on scaled ring mock-ups (1550 MPa). Black-Right-Pointing-Pointer Creep tests showed very low creep strain and creep rates. Black-Right-Pointing-Pointer Long term tests showed no significant stress relaxation on the ring mock-ups. - Abstract: After a first R and D and testing activity to develop and characterize by tensile and creep tests a high strength glass fiber-epoxy composite as reference material for the manufacture of ITER pre-compression rings, ENEA designed and manufactured a dedicated testing facility and different sub-scale composite ring mock-ups in order to characterize their mechanical properties. The paper reports the results of the overall testing activities performed during the last years on a total number of eleven sub-scale pre-compression ring mock-ups manufactured by winding S2 glass fibers on a diameter of 1 m (1/5 of the full scale) both by vacuum pressure epoxy impregnation (VPI) and filament wet winding techniques (WW). The first three rings were manufactured by ENEA Frascati thanks to a particular VPI technique; one of them was used as base composite material to manufacture different sets of specimens for shear, compression and non destructive tests (NDT). Then, five other mock-ups were manufactured following ENEA VPI process and three using WW technique by two different industrial companies. The rings were tested in ENEA Frascati in a dedicated hydraulic testing machine consisting of 18 radial actuators working in position control with a total load capability of 1000 tons. The complete testing campaign consisted of six ultimate tensile strength (UTS) tests and four stress relaxation (SR) tests. The tests demonstrated that the composite (S2 glass-epoxy) is a valid and viable solution for the ITER pre-compression

Optimizing beam transport in rapidly compressing beams on the neutralized drift compression experiment – II

Directory of Open Access Journals (Sweden)

Anton D. Stepanov

2018-03-01

Full Text Available The Neutralized Drift Compression Experiment-II (NDCX-II is an induction linac that generates intense pulses of 1.2 MeV helium ions for heating matter to extreme conditions. Here, we present recent results on optimizing beam transport. The NDCX-II beamline includes a 1-m-long drift section downstream of the last transport solenoid, which is filled with charge-neutralizing plasma that enables rapid longitudinal compression of an intense ion beam against space-charge forces. The transport section on NDCX-II consists of 28 solenoids. Finding optimal field settings for a group of solenoids requires knowledge of the envelope parameters of the beam. Imaging the beam on the scintillator gives the radius of the beam, but the envelope angle is not measured directly. We demonstrate how the parameters of the beam envelope (radius, envelop angle, and emittance can be reconstructed from a series of images taken by varying the B-field strengths of a solenoid upstream of the scintillator. We use this technique to evaluate emittance at several points in the NDCX-II beamline and for optimizing the trajectory of the beam at the entry of the plasma-filled drift section. Keywords: Charged-particle beams, Induction accelerators, Beam dynamics, Beam emittance, Ion beam diagnostics, PACS Codes: 41.75.-i, 41.85.Ja, 52.59.Sa, 52.59.Wd, 29.27.Eg

Cross-coupling effects in chemically non-equilibrium viscous compressible flows

International Nuclear Information System (INIS)

Kustova, E.V.; Giordano, D.

2011-01-01

Graphical abstract: Self-cosistent kinetic-theory description of chemical-reaction rates and mean normal stress in one-temperature viscous compressible gas flows. Reaearch highlights: → In chemically non-equilibrium viscous compressible flows, the rate of each reaction depends on the velocity divergence and rates of all other reactions. → Cross effects between the rates of chemical reactions and normal mean stress can be found in the symmetric form and expressed in terms of the reaction affinities. → In the case of small affinities, the entropy production is unconditionally non-negative; in the case of finite affinities, the entropy production related to the scalar forces has no definite sign. - Abstract: A closed self-consistent description of a one-temperature non-equilibrium reacting flow is presented on the basis of the kinetic theory methods. A general case including internal degrees of freedom, dissociation-recombination and exchange reactions, and arbitrary values of affinities of chemical reactions is considered. Chemical-reaction rates and mean normal stress in viscous compressible flows are studied and a symmetric cross coupling between these terms is found. It is shown that the rate of each chemical reaction and the mean normal stress depend on velocity divergence and affinities of all chemical reactions; the law of mass action is violated in viscous flows. The results obtained in the frame of linear irreversible thermodynamics can be deduced from the proposed model for the particular case of small affinities. The reciprocal Onsager-Casimir relations are verified, the symmetry of kinetic coefficients is demonstrated, and the entropy production in a viscous flow is studied.

Relationship Factors and Trajectories of Intimate Partner Violence among South African Women during Pregnancy and the Postpartum Period

Science.gov (United States)

Groves, Allison K.; McNaughton-Reyes, H. Luz; Foshee, Vangie A.; Moodley, Dhayendre; Maman, Suzanne

2014-01-01

Intimate partner violence (IPV) is a significant public health problem in South Africa. However, there is limited research on whether and how IPV changes during pregnancy and the postpartum period and on the factors that might affect women's risk during this time. In this study, we describe the mean trajectories of physical and psychological IPV during pregnancy and the postpartum period and examine whether relationship power, partner social support, and relationship stress are associated with women's trajectories of IPV. Data come from a longitudinal study with 1,480 women recruited during pregnancy between May 2008 and June 2010 at a public clinic in Durban. Women completed behavioral assessments at their first antenatal visit, at fourteen weeks and at nine months postpartum. Women's experiences of IPV were measured at all three time points and relationship power, partner social support and relationship stress were each measured at the baseline assessment. We used multilevel random coefficients growth modeling to build our models. The mean trajectory for both types of IPV was flat which means that, on average, there was not significant change in levels of IPV over pregnancy and the postpartum period. However, there was significant individual variability in trajectories of IPV over the study period. Women who had higher relationship power had lower levels of physical and psychological IPV over time than women with lower relationship power. Additionally, women with higher relationship stress and lower partner support had higher levels of psychological IPV at pregnancy. Interventions that maximize women's relationship power and partner social support and minimize relationship stress during this transformative time are needed. PMID:25268363

Adaptive robust trajectory tracking control of a parallel manipulator driven by pneumatic cylinders

Directory of Open Access Journals (Sweden)

Ce Shang

2016-04-01

Full Text Available Due to the compressibility of air, non-linear characteristics, and parameter uncertainties of pneumatic elements, the position control of a pneumatic cylinder or parallel platform is still very difficult while comparing with the systems driven by electric or hydraulic power. In this article, based on the basic dynamic model and descriptions of thermal processes, a controller integrated with online parameter estimation is proposed to improve the performance of a pneumatic cylinder controlled by a proportional valve. The trajectory tracking error is significantly decreased by applying this method. Moreover, the algorithm is expanded to the problem of posture trajectory tracking for the three-revolute prismatic spherical pneumatic parallel manipulator. Lyapunov’s method is used to give the proof of stability of the controller. Using NI-CompactRio, NI-PXI, and Veristand platform as the realistic controller hardware and data interactive environment, the adaptive robust control algorithm is applied to the physical system successfully. Experimental results and data analysis showed that the posture error of the platform could be about 0.5%–0.7% of the desired trajectory amplitude. By integrating this method to the mechatronic system, the pneumatic servo solutions can be much more competitive in the industrial market of position and posture control.

Stress path dependent hydromechanical behaviour of heterogeneous carbonate rock

Directory of Open Access Journals (Sweden)

Dimanov A.

2010-06-01

Full Text Available The influence of stress paths, representative of reservoir conditions, on the hydromechanical behavior of a moderately heterogeneous carbonate has been investigated. Multiscale structural heterogeneities, common for instance in carbonate rocks, can strongly alter the mechanical response and significantly influence the evolution of flow properties with stress. Using a triaxial cell, the permeability evolutions during compression and the effects of brittle (fracture and plastic (pore collapse deformations at yield, were measured. A strong scattering was observed on the mechanical response both in term of compressibility and failure threshold. Using the porosity scaling predicted by an adapted effective medium theory (based on crack growth under Hertzian contact, we have rescaled the critical pressures by the normalized porosity deviation. This procedure reduces efficiently the scattering, revealing in the framework of proportional stress path loading, a linear relation between the critical pressures and the stress path parameter through all the deformation regimes. It leads to a new formulation for the critical state envelope in the 'mean stress, deviatoric stress' diagram. The attractive feature of this new yield envelope formulation relies on the fact that only the two most common different mechanical tests 'Uniaxial Compression' and 'Hydrostatic Compression', are needed to define entirely the yield envelope. Volumic strains and normalized permeabilities are finally mapped in the stresses diagram and correlated.

PANTHER. Trajectory Analysis

Energy Technology Data Exchange (ETDEWEB)

Rintoul, Mark Daniel [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Wilson, Andrew T. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Valicka, Christopher G. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Kegelmeyer, W. Philip [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Shead, Timothy M. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Newton, Benjamin D. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Czuchlewski, Kristina Rodriguez [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

2015-09-01

We want to organize a body of trajectories in order to identify, search for, classify and predict behavior among objects such as aircraft and ships. Existing compari- son functions such as the Fr'echet distance are computationally expensive and yield counterintuitive results in some cases. We propose an approach using feature vectors whose components represent succinctly the salient information in trajectories. These features incorporate basic information such as total distance traveled and distance be- tween start/stop points as well as geometric features related to the properties of the convex hull, trajectory curvature and general distance geometry. Additionally, these features can generally be mapped easily to behaviors of interest to humans that are searching large databases. Most of these geometric features are invariant under rigid transformation. We demonstrate the use of different subsets of these features to iden- tify trajectories similar to an exemplar, cluster a database of several hundred thousand trajectories, predict destination and apply unsupervised machine learning algorithms.

An exponential material model for prediction of the flow curves of several AZ series magnesium alloys in tension and compression

International Nuclear Information System (INIS)

Fereshteh-Saniee, F.; Barati, F.; Badnava, H.; Fallah Nejad, Kh.

2012-01-01

Highlights: ► The exponential model can represent flow behaviors of AZ series Mg alloys very well. ► Strain rate sensitivities of AZ series Mg alloys in compression are nearly the same. ► Effect of zinc element on tensile activation energy is higher than on compressive one. ► Activation energies of AZ80 and AZ81 in tension were greater than in compression. ► Tensile and compressive rate sensitivities of AZ80 are not close to each other. -- Abstract: This paper is concerned with flow behaviors of several magnesium alloys, such as AZ31, AZ80 and AZ81, in tension and compression. The experiments were performed at elevated temperatures and for various strain rates. In order to eliminate the effect of inhomogeneous deformation in tensile and compression tests, the Bridgeman’s and numerical correction factors were respectively employed. A two-section exponential mathematical model was also utilized for prediction of flow stresses of different magnesium alloys in tension and compression. Moreover, based on the compressive flow model proposed, the peak stress and the relevant true strain could be estimated. The true stress and strain of the necking point can also be predicted using the corresponding relations. It was found that the flow behaviors estimated by the exponential flow model were encouragingly in very good agreement with experimental findings.

DNABIT Compress – Genome compression algorithm

OpenAIRE

Rajarajeswari, Pothuraju; Apparao, Allam

2011-01-01

Data compression is concerned with how information is organized in data. Efficient storage means removal of redundancy from the data being stored in the DNA molecule. Data compression algorithms remove redundancy and are used to understand biologically important molecules. We present a compression algorithm, “DNABIT Compress” for DNA sequences based on a novel algorithm of assigning binary bits for smaller segments of DNA bases to compress both repetitive and non repetitive DNA sequence. Our ...

Stress gradients in CrN coatings

NARCIS (Netherlands)

Janssen, G.C.A.M.; Tichelaar, F.D.; Visser, C.C.G.

2006-01-01

Stress in hard films is the net sum of tensile stress generated at the grain boundaries, compressive stress due to ion peening, and thermal stress due to the difference in thermal expansion of the coating and substrate. The tensile part due to grain boundaries is thickness dependent. The other two

Factors that Influence Trajectories of Delinquency Throughout Adolescence.

Science.gov (United States)

Evans, Sara Z; Simons, Leslie Gordon; Simons, Ronald L

2016-01-01

Given that one of the most powerful predictors of adult crime is the presence of behavior problems in childhood and adolescence, there is a need to further understand factors that determine behavior patterns during this developmental stage. This study focuses on stressful life experiences such as exposure to delinquent peers, racial discrimination, as well as family characteristics such as parenting style and family transitions. Data come from four waves of the Family and Community Health Survey, an African-American sample. The present study investigates 354 males from this dataset. We utilize a group-based trajectory model to estimate the number and type of trajectories of delinquency. We then estimate multinomial regression models to predict trajectory group membership. The results indicated that there were four distinct groups of offenders (negligible delinquents; early starter/declining; late starter; and early starter/chronic offenders). We predicted group membership using both early predictors and measures of change in these predictors across the study period. The results indicated that individuals who experience greater racial discrimination (both early in childhood and throughout adolescence) are more likely to be in trajectory groups that begin offending early and persist through adolescence. Additionally, those respondents who reported having friends with greater delinquent behavior were more likely to be in groups that began their offending early in life and persisted when compared to groups who started later or desisted as they entered adulthood. The results contribute to developmental research and provide information that may be helpful in preventing adolescents from persisting in antisocial behavior as they enter adulthood.

Compressive Behavior of Fiber-Reinforced Concrete with End-Hooked Steel Fibers.

Science.gov (United States)

Lee, Seong-Cheol; Oh, Joung-Hwan; Cho, Jae-Yeol

2015-03-27

In this paper, the compressive behavior of fiber-reinforced concrete with end-hooked steel fibers has been investigated through a uniaxial compression test in which the variables were concrete compressive strength, fiber volumetric ratio, and fiber aspect ratio (length to diameter). In order to minimize the effect of specimen size on fiber distribution, 48 cylinder specimens 150 mm in diameter and 300 mm in height were prepared and then subjected to uniaxial compression. From the test results, it was shown that steel fiber-reinforced concrete (SFRC) specimens exhibited ductile behavior after reaching their compressive strength. It was also shown that the strain at the compressive strength generally increased along with an increase in the fiber volumetric ratio and fiber aspect ratio, while the elastic modulus decreased. With consideration for the effect of steel fibers, a model for the stress-strain relationship of SFRC under compression is proposed here. Simple formulae to predict the strain at the compressive strength and the elastic modulus of SFRC were developed as well. The proposed model and formulae will be useful for realistic predictions of the structural behavior of SFRC members or structures.

Mechanical Properties of Steel-FRP Composite Bars under Tensile and Compressive Loading

Directory of Open Access Journals (Sweden)

Zeyang Sun

2017-01-01

Full Text Available The factory-produced steel-fiber reinforced polymer composite bar (SFCB is a new kind of reinforcement for concrete structures. The manufacturing technology of SFCB is presented based on a large number of handmade specimens. The calculated stress-strain curves of ordinary steel bar and SFCB under repeated tensile loading agree well with the corresponding experimental results. The energy-dissipation capacity and residual strain of both steel bar and SFCB were analyzed. Based on the good simulation results of ordinary steel bar and FRP bar under compressive loading, the compressive behavior of SFCB under monotonic loading was studied using the principle of equivalent flexural rigidity. There are three failure modes of SFCB under compressive loading: elastic buckling, postyield buckling, and no buckling (ultimate compressive strength is reached. The increase in the postyield stiffness of SFCB rsf can delay the postyield buckling of SFCB with a large length-to-diameter ratio, and an empirical equation for the relationship between the postbuckling stress and rsf is suggested, which can be used for the design of concrete structures reinforced by SFCB to consider the effect of reinforcement buckling.

Safety for Compressed Gas and Air Equipment. Module SH-26. Safety and Health.

Science.gov (United States)

Center for Occupational Research and Development, Inc., Waco, TX.

This student module on safety for compressed gas and air equipment is one of 50 modules concerned with job safety and health. This module presents technical data about commonly used gases and stresses the procedures necessary for safe handling of compressed gases. Following the introduction, 14 objectives (each keyed to a page in the text) the…

Modeling Compressed Turbulence with BHR

Science.gov (United States)

Israel, Daniel

2011-11-01

Turbulence undergoing compression or expansion occurs in systems ranging from internal combustion engines to supernovae. One common feature in many of these systems is the presence of multiple reacting species. Direct numerical simulation data is available for the single-fluid, low turbulent Mach number case. Wu, et al. (1985) compared their DNS results to several Reynolds-averaged Navier-Stokes models. They also proposed a three-equation k - ɛ - τ model, in conjunction with a Reynolds-stress model. Subsequent researchers have proposed alternative corrections to the standard k - ɛ formulation. Here we investigate three variants of the BHR model (Besnard, 1992). BHR is a model for multi-species variable-density turbulence. The three variants are the linear eddy-viscosity, algebraic-stress, and full Reynolds-stress formulations. We then examine the predictions of the model for the fluctuating density field for the case of variable-density turbulence.

Adaptive Trajectory Design

Data.gov (United States)

National Aeronautics and Space Administration — Adaptive Trajectory Design (ATD) is an original concept for quick and efficient end-to-end trajectory designs using proven piece-wise dynamical methods. With ongoing...

Hot Deformation Behavior and a Two-Stage Constitutive Model of 20Mn5 Solid Steel Ingot during Hot Compression

Directory of Open Access Journals (Sweden)

Min Liu

2018-03-01

Full Text Available 20Mn5 steel is widely used in the manufacture of heavy hydro-generator shaft forging due to its strength, toughness, and wear resistance. However, the hot deformation and recrystallization behaviors of 20Mn5 steel compressed under a high temperature were not studied. For this article, hot compression experiments under temperatures of 850–1200 °C and strain rates of 0.01 s−1–1 s−1 were conducted using a Gleeble-1500D thermo-mechanical simulator. Flow stress-strain curves and microstructure after hot compression were obtained. Effects of temperature and strain rate on microstructure are analyzed. Based on the classical stress-dislocation relationship and the kinetics of dynamic recrystallization, a two-stage constitutive model is developed to predict the flow stress of 20Mn5 steel. Comparisons between experimental flow stress and predicted flow stress show that the predicted flow stress values are in good agreement with the experimental flow stress values, which indicates that the proposed constitutive model is reliable and can be used for numerical simulation of hot forging of 20Mn5 solid steel ingot.

Compressive failure with interacting cracks

International Nuclear Information System (INIS)

Yang Guoping; Liu Xila

1993-01-01

The failure processes in concrete and other brittle materials are just the results of the propagation, coalescence and interaction of many preexisting microcracks or voids. To understand the real behaviour of the brittle materials, it is necessary to bridge the gap from the relatively matured one crack behaviour to the stochastically distributed imperfections, that is, to concern the crack propagation and interaction of microscopic mechanism with macroscopic parameters of brittle materials. Brittle failure in compression has been studied theoretically by Horii and Nemat-Nasser (1986), in which a closed solution was obtained for a preexisting flaw or some special regular flaws. Zaitsev and Wittmann (1981) published a paper on crack propagation in compression, which is so-called numerical concrete, but they did not take account of the interaction among the microcracks. As for the modelling of the influence of crack interaction on fracture parameters, many studies have also been reported. Up till now, some researcher are working on crack interaction considering the ratios of SIFs with and without consideration of the interaction influences, there exist amplifying or shielding effects of crack interaction which are depending on the relative positions of these microcracks. The present paper attempts to simulate the whole failure process of brittle specimen in compression, which includes the complicated coupling effects between the interaction and propagation of randomly distributed or other typical microcrack configurations step by step. The lengths, orientations and positions of microcracks are all taken as random variables. The crack interaction among many preexisting random microcracks is evaluated with the help of a simple interaction matrix (Yang and Liu, 1991). For the subcritically stable propagation of microcracks in mixed mode fracture, fairly known maximum hoop stress criterion is adopted to compute branching lengths and directions at each tip of the crack

Residual stress in deuterium implanted nominal copper coatings

International Nuclear Information System (INIS)

Inal, M. Y.; Alam, M.; Peascoe, R. A.; Watkins, T. R.

2000-01-01

The effects of deuterium (D) implantation on the residual stresses in Cu and CuAl 2 phases present in nominal Cu coatings (containing Al) deposited on Al-alloy (Al-6061) substrates were measured using an x-ray diffraction technique. The coatings were deposited by radio frequency magnetron sputtering of a pure Cu target under identical conditions and Al was incorporated in the coatings during growth by diffusion from the substrate. Deuterium was implanted in the coatings at energies of 40 or 40+120 keV with fluences of 1x10 21 , 2x10 21 , or 3x10 21 D + /m 2 . Pole figures of the Cu phase in the coatings prior to and after implantation indicated no effect of implantation on the fibrous texture. Triaxial stress analysis indicated the surface normal stress component to be negligible in Cu and slightly tensile in CuAl 2 under all conditions. Furthermore, under all conditions, the in-plane residual stresses in both phases were found to be compressive and nearly isotropic. The magnitude of the isotropic compressive stress was always higher in CuAl 2 as compared to Cu. The compressive residual stresses in the Cu phase changed only mildly with increasing coating weight, ion energy, and fluence. However, in the CuAl 2 phase the compressive residual stresses changed markedly with increasing ion energy (initial decrease followed by leveling off) and increasing ion fluence (initial decrease followed by an increase), but remained unaffected by increasing coating weight. (c) 2000 American Institute of Physics

The fatigue behavior of composite laminates under various mean stresses

Science.gov (United States)

Rotem, A.

1991-01-01

A method is developed for predicting the S-N curve of a composite laminate which is subjected to an arbitrary stress ratio, R (minimum stress/maximum stress). The method is based on the measuring of the S-N behavior of two distinct cases, tension-tension and compression-compression fatigue loadings. Using these parameters, expressions are formulated that estimate the fatigue behavior under any stress ratio loading. Experimental results from the testing of graphite/epoxy laminates, with various structures, are compared with the predictions and show good agreement.

Compressive Deformation Behavior of Closed-Cell Micro-Pore Magnesium Composite Foam

Directory of Open Access Journals (Sweden)

Jing Wang

2018-05-01

Full Text Available The closed-cell micro-pore magnesium composite foam with hollow ceramic microspheres (CMs was fabricated by a modified melt foaming method. The effect of CMs on the compressive deformation behavior of CM-containing magnesium composite foam was investigated. Optical microscopy and scanning electron microscopy were used for observation of the microstructure. Finite element modeling of the magnesium composite foam was established to predict localized stress, fracture of CMs, and the compressive deformation behavior of the foam. The results showed that CMs and pores directly affected the compressive deformation behavior of the magnesium composite foam by sharing a part of load applied on the foam. Meanwhile, the presence of Mg2Si phase influenced the mechanical properties of the foam by acting as the crack source during the compression process.

Failure Waves in Shock-Compressed Glasses

International Nuclear Information System (INIS)

Kanel, G. I.

2006-01-01

The failure wave is a network of cracks that are nucleated on the surface and propagate into the elastically stressed body. It is a mode of catastrophic fracture in an elastically stressed media whose relevance is not limited to impact events. In the paper, main properties of the failure waves are summarized and discussed. It has been shown that the failure wave is really a wave process which is characterized by small increase of the longitudinal stress and corresponding increments of the particle velocity and the density. The propagation velocity of the failure wave is less than the sound speed; it is not directly related to the compressibility but is determined by the crack growth speed. The failure wave is steady if the stress state ahead of it is supported unchanging. In some sense the process is similar to a subsonic combustion wave. Computer simulations based on the phenomenological combustion-like model reproduces well all kinematical aspects of the phenomenon

The interaction of fatigue cracks with a residual stress field using thermoelastic stress analysis and synchrotron X-ray diffraction experiments

Science.gov (United States)

Amjad, Khurram; Asquith, David; Sebastian, Christopher M.; Wang, Wei-Chung

2017-01-01

This article presents an experimental study on the fatigue behaviour of cracks emanating from cold-expanded holes utilizing thermoelastic stress analysis (TSA) and synchrotron X-ray diffraction (SXRD) techniques with the aim of resolving the long-standing ambiguity in the literature regarding potential relaxation, or modification, of beneficial compressive residual stresses as a result of fatigue crack propagation. The crack growth rates are found to be substantially lower as the crack tip moved through the residual stress zone induced by cold expansion. The TSA results demonstrated that the crack tip plastic zones were reduced in size by the presence of the residual compressive stresses induced by cold expansion. The crack tip plastic zones were found to be insignificant in size in comparison to the residual stress zone resulting from cold expansion, which implied that they were unlikely to have had a notable impact on the surrounding residual stresses induced by cold expansion. The residual stress distributions measured along the direction of crack growth, using SXRD, showed no signs of any significant stress relaxation or redistribution, which validates the conclusions drawn from the TSA data. Fractographic analysis qualitatively confirmed the influence on crack initiation of the residual stresses induced by the cold expansion. It was found that the application of single compressive overload caused a relaxation, or reduction in the residual stresses, which has wider implications for improving the fatigue life. PMID:29291095

Fracture Behaviours in Compression-loaded Triangular Corrugated Core Sandwich Panels

Directory of Open Access Journals (Sweden)

Zaid N.Z.M.

2016-01-01

Full Text Available The failure modes occurring in sandwich panels based on the corrugations of aluminium alloy, carbon fibre-reinforced plastic (CFRP and glass fibre-reinforced plastic (GFRP are analysed in this work. The fracture behaviour of these sandwich panels under compressive stresses is determined through a series of uniform lateral compression performed on samples with different cell wall thicknesses. Compression test on the corrugated-core sandwich panels were conducted using an Instron series 4505 testing machine. The post-failure examinations of the corrugated-core in different cell wall thickness were conducted using optical microscope. Load-displacement graphs of aluminium alloy, GFRP and CFRP specimens were plotted to show progressive damage development with five unit cells. Four modes of failure were described in the results: buckling, hinges, delamination and debonding. Each of these failure modes may dominate under different cell wall thickness or loading condition, and they may act in combination. The results indicate that thicker composites corrugated-core panels tend can recover more stress and retain more stiffness. This analysis provides a valuable insight into the mechanical behaviour of corrugated-core sandwich panels for use in lightweight engineering applications.

Compressible turbulent flows: aspects of prediction and analysis

Energy Technology Data Exchange (ETDEWEB)

Friedrich, R. [TU Muenchen, Garching (Germany). Fachgebiet Stroemungsmechanik

2007-03-15

variation as sources in the pressure Poisson equation rather than wave propagation phenomena. This opens new challenges to turbulence modellers and underlines the need to treat compressibility effects via the full Reynolds stress equations. (orig.)

First application of the 3D-MHB on dynamic compressive behavior of UHPC

Directory of Open Access Journals (Sweden)

Cadoni Ezio

2015-01-01

Full Text Available In order to study the dynamic behaviour of material in confined conditions a new machine was conceived and called 3D-Modified Hopkinson Bar (3D-MHB. It is a Modified Hopkinson Bar apparatus designed to apply dynamic loading in materials having a tri-axial stress state. It consists of a pulse generator system (with pre-tensioned bar and brittle joint, 1 input bar, and 5 output bars. The first results obtained on Ultra High Performance Concrete in compression with three different mono-axial compression states are presented. The results show how the pre-stress states minimize the boundary condition and a more uniform response is obtained.

Application of PDF methods to compressible turbulent flows

Science.gov (United States)

Delarue, B. J.; Pope, S. B.

1997-09-01

A particle method applying the probability density function (PDF) approach to turbulent compressible flows is presented. The method is applied to several turbulent flows, including the compressible mixing layer, and good agreement is obtained with experimental data. The PDF equation is solved using a Lagrangian/Monte Carlo method. To accurately account for the effects of compressibility on the flow, the velocity PDF formulation is extended to include thermodynamic variables such as the pressure and the internal energy. The mean pressure, the determination of which has been the object of active research over the last few years, is obtained directly from the particle properties. It is therefore not necessary to link the PDF solver with a finite-volume type solver. The stochastic differential equations (SDE) which model the evolution of particle properties are based on existing second-order closures for compressible turbulence, limited in application to low turbulent Mach number flows. Tests are conducted in decaying isotropic turbulence to compare the performances of the PDF method with the Reynolds-stress closures from which it is derived, and in homogeneous shear flows, at which stage comparison with direct numerical simulation (DNS) data is conducted. The model is then applied to the plane compressible mixing layer, reproducing the well-known decrease in the spreading rate with increasing compressibility. It must be emphasized that the goal of this paper is not as much to assess the performance of models of compressibility effects, as it is to present an innovative and consistent PDF formulation designed for turbulent inhomogeneous compressible flows, with the aim of extending it further to deal with supersonic reacting flows.

Elastic stress transmission and transformation (ESTT) by confined liquid: A new mechanics for fracture in elastic lithosphere of the earth

Science.gov (United States)

Xu, Xing-Wang; Peters, Stephen; Liang, Guang-He; Zhang, Bao-Lin

2016-01-01

We report on a new mechanical principle, which suggests that a confined liquid in the elastic lithosphere has the potential to transmit a maximum applied compressive stress. This stress can be transmitted to the internal contacts between rock and liquid and would then be transformed into a normal compressive stress with tangential tensile stress components. During this process, both effective compressive normal stress and tensile tangential stresses arise along the liquid–rock contact. The minimum effective tensile tangential stress causes the surrounding rock to rupture. Liquid-driven fracture initiates at the point along the rock–liquid boundary where the maximum compressive stress is applied and propagates along a plane that is perpendicular to the minimum effective tensile tangential stress and also is perpendicular to the minimum principal stress.

The Taylor relation in compression deformed Ge single crystals

International Nuclear Information System (INIS)

Nyilas, K; Ungar, T; Dupas, C; Martin, J L; Kruml, T

2010-01-01

Ge single crystals are deformed in compression at 850K and the same strain rate to various extents of strains. In each sample, the internal stress is measured through stress reduction tests and the dislocation densities by X-ray measurements. Data about these two parameters follow fairly well the Taylor-Saada relation, provided a correction term is added. It probably corresponds to dislocations which are seen by X-rays, though they do not contribute to crystal hardening.

Stress strain flow curves for Cu-OFP

International Nuclear Information System (INIS)

Sandstroem, Rolf; Hallgren, Josefin

2009-04-01

Stress strain curves of oxygen free copper alloyed with phosphorus Cu-OFP have been determined in compression and tension. The compression tests were performed at room temperature for strain rates between 10 -5 and 10 -3 1/s. The tests in tension covered the temperature range 20 to 175 deg C for strain rates between 10 -7 and 5x10 -3 1/s. The results in compression and tension were close for similar strain rates. A model for stress strain curves has been formulated using basic dislocation mechanisms. The model has been set up in such a way that fitting of parameters to the curves is avoided. By using a fundamental creep model as a basis a direct relation to creep data has been established. The maximum engineering flow stress in tension is related to the creep stress giving the same strain rate. The model reproduces the measured flow curves as function of temperature and strain rate in the investigated interval. The model is suitable to use in finite-element computations of structures in Cu-OFP

Characterization of Human Dental Pulp Tissue Under Oscillatory Shear and Compression.

Science.gov (United States)

Ozcan, Burak; Bayrak, Ece; Erisken, Cevat

2016-06-01

Availability of material as well as biological properties of native tissues is critical for biomaterial design and synthesis for regenerative engineering. Until recently, selection of biomaterials and biomolecule carriers for dental pulp regeneration has been done randomly or based on experience mainly due to the absence of benchmark data for dental pulp tissue. This study, for the first time, characterizes the linear viscoelastic material functions and compressive properties of human dental pulp tissue harvested from wisdom teeth, under oscillatory shear and compression. The results revealed a gel-like behavior of the pulp tissue over the frequency range of 0.1-100 rps. Uniaxial compression tests generated peak normal stress and compressive modulus values of 39.1 ± 20.4 kPa and 5.5 ± 2.8 kPa, respectively. Taken collectively, the linear viscoelastic and uniaxial compressive properties of the human dental pulp tissue reported here should enable the better tailoring of biomaterials or biomolecule carriers to be employed in dental pulp regeneration.

Modelling and simulation of the compressible turbulence in supersonic shear flows

International Nuclear Information System (INIS)

Guezengar, Dominique

1997-02-01

This research thesis addresses the modelling of some specific physical problems of fluid mechanics: compressibility (issue of mixing layers), large variations of volumetric mass (boundary layers), and anisotropy (compression ramps). After a presentation of the chosen physical modelling and numerical approximation, the author pays attention to flows at the vicinity of a wall, and to boundary conditions. The next part addresses existing compressibility models and their application to the calculation of supersonic mixing layers. A critical assessment is also performed through calculations of boundary layers and of compression ramps. The next part addresses problems related to large variations of volumetric mass which are not taken by compressibility models into account. A modification is thus proposed for the diffusion term, and is tested for the case of supersonic boundary layers and of mixing layers with high density rates. Finally, anisotropy effects are addressed through the implementation of Explicit Algebraic Stress k-omega Turbulence models (EARSM), and their tests on previously studied cases [fr

Estimation of hardness and compressive strength of SP 100 aluminum powder epoxy

Energy Technology Data Exchange (ETDEWEB)

Han, Jeong Young [Pusan National Univ., Busan (Korea, Republic of); Kim, Myung Hun [Korea Institute of Footwear and Leather Technology, Busan (Korea, Republic of); Kang, Sung Soo [Jeonju Univ., Jeonju (Korea, Republic of)

2012-09-15

In this study, we performed experimental tests on five SP 100 aluminum powder epoxy specimens with several after curing conditions in order to estimate their hardness with temperature and compressive strength. In the surface hardness test, it was found that the higher the after curing temperature, the higher was the hardness. In particular, it was found that the hardness of the specimens in cases 3 and 4 was much higher than in the other cases. In addition, in the compression tests carried out to evaluate the compressive strength, it was found that the specimens showed relatively similar stiffness and strength with after curing, and specimens with no after curing showed compression stress strain curves similar to those of thermoplastic resins.

Estimation of hardness and compressive strength of SP 100 aluminum powder epoxy

International Nuclear Information System (INIS)

Han, Jeong Young; Kim, Myung Hun; Kang, Sung Soo

2012-01-01

In this study, we performed experimental tests on five SP 100 aluminum powder epoxy specimens with several after curing conditions in order to estimate their hardness with temperature and compressive strength. In the surface hardness test, it was found that the higher the after curing temperature, the higher was the hardness. In particular, it was found that the hardness of the specimens in cases 3 and 4 was much higher than in the other cases. In addition, in the compression tests carried out to evaluate the compressive strength, it was found that the specimens showed relatively similar stiffness and strength with after curing, and specimens with no after curing showed compression stress strain curves similar to those of thermoplastic resins

Permeability of Concrete with Recycled Concrete Aggregate and Pozzolanic Materials under Stress.

Science.gov (United States)

Wang, Hailong; Sun, Xiaoyan; Wang, Junjie; Monteiro, Paulo J M

2016-03-30

The research reported herein studied the permeability of concrete containing recycled-concrete aggregate (RA), superfine phosphorous slag (PHS), and ground granulated blast-furnace slag (GGBS) with and without stress. Test results showed that the chloride diffusion coefficient of RA concrete (RAC) without external loads decreased with time, and the permeability of RAC is much lower than that of the reference concrete due to the on-going hydration and the pozzolanic reaction provided by the PHS and GGBS additives in the RAC mixture. The permeability of chloride under flexural load is much more sensitive than that under compressive load due to the differences in porosity and cracking pattern. At low compressive stress levels, the permeability of chloride decreased by the closing of pores and microcracks within RAC specimens. However, in a relatively short time the chloride diffusion coefficient and the chloride content increased rapidly with the increase of compressive stress when it exceeded a threshold stress level of approximate 35% of the ultimate compressive strength. Under flexural stress, the chloride transport capability increased with the increase of stress level and time. At high compressive and flexural stress levels, creep had a significant effect on the permeability of chloride in the RAC specimens due to the damage from the nucleation and propagation of microcracks over time. It is apparent that mortar cracking has more of a significant effect on the chloride transport in concrete than cracking in the interfacial transition zone (ITZ).

The Diagonal Compression Field Method using Circular Fans

DEFF Research Database (Denmark)

Hansen, Thomas

2006-01-01

is a modification of the traditional method, the modification consisting of the introduction of circular fan stress fields. To ensure proper behaviour for the service load the -value ( = cot, where  is the angle relative to the beam axis of the uniaxial concrete compression) chosen should not be too large...

[Contact characteristics research of acetabular weight-bearing area with different internal fixation methods after compression fracture of acetabular dome].

Science.gov (United States)

Xu, Bowen; Zhang, Qingsong; An, Siqi; Pei, Baorui; Wu, Xiaobo

2017-08-01

To establish the model of compression fracture of acetabular dome, and to measure the contact characteristics of acetabular weight-bearing area of acetabulum after 3 kinds of internal fixation. Sixteen fresh adult half pelvis specimens were randomly divided into 4 groups, 4 specimens each group. Group D was the complete acetabulum (control group), and the remaining 3 groups were prepared acetabular dome compression fracture model. The fractures were fixed with reconstruction plate in group A, antegrade raft screws in group B, and retrograde raft screws in group C. The pressure sensitive films were attached to the femoral head, and the axial compression test was carried out on the inverted single leg standing position. The weight-bearing area, average stress, and peak stress were measured in each group. Under the loading of 500 N, the acetabular weight-bearing area was significantly higher in group D than in other 3 groups ( P area were significantly higher in group B and group C than in group A, and the average stress and peak stress were significantly lower than in group A ( P 0.05). For the compression fracture of the acetabular dome, the contact characteristics of the weight-bearing area can not restore to the normal level, even if the anatomical reduction and rigid internal fixation were performed; compared with the reconstruction plate fixation, antegrade and retrograde raft screws fixations can increase the weight-bearing area, reduce the average stress and peak stress, and reduce the incidence of traumatic arthritis.

Trajectories of self-rated health among veterans: a latent growth curve analysis of the impact of posttraumatic symptoms.

Science.gov (United States)

Benyamini, Yael; Ein-Dor, Tsachi; Ginzburg, Karni; Solomon, Zahava

2009-04-01

To examine the effects of combat stress reaction (CSR) and posttraumatic stress symptoms (PTS) on the level and trajectories of self-rated health (SRH) over 20 years after war exposure. A total of 675 veterans comprising two groups, a CSR group (n = 369) and a matched control group without CSR (n = 306), were assessed in a prospective longitudinal design, 1, 2, 3, and 20 years after their participation in the 1982 Lebanon War. SRH and PTS were assessed repeatedly, at each point of measurement. The CSR participants showed more impaired initial SRH than the controls. Although the CSR group showed an improvement in SRH over time, its SRH level remained lower than that of the control group in all 4 points in time. Initial levels of PTS were associated with more impaired SRH and lower improvement over time. In addition, increased levels of PTS in the first follow-up period were related to poorer SRH, in comparison to the predicted trajectory on the basis of CSR and initial PTS. Stress reaction to war trauma affected the trajectory of SRH over a 20-year period. Although the differences between veterans who had shown acute stress reaction and those who had not persisted over the entire period, there was slow improvement in SRH over time among the more impaired CSR group. PTS in the first years after the war slowed this improvement and thus played a key role in the relationship between war trauma and physical health.

Stress and resource pathways connecting early socioeconomic adversity to young adults' physical health risk.

Science.gov (United States)

Wickrama, Kandauda K A S; Lee, Tae Kyoung; O'Neal, Catherine Walker; Kwon, Josephine A

2015-05-01

Although research has established the impact of early stress, including stressful life contexts, and early resources, such as educational attainment, on various adolescent health outcomes, previous research has not adequately investigated "integrative models" incorporating both stress and resource mediational pathways to explain how early socioeconomic adversity impacts physical health outcomes, particularly in early life stages. Data on early childhood/adolescent stress and socioeconomic resources as well as biomarkers indicating physical health status in young adulthood were collected from 11,798 respondents (54 % female) over a 13-year period from youth participating in the National Study of Adolescent Health (Add Health). Physical health risk in young adulthood was measured using a composite index of nine regulatory biomarkers of cardiovascular and metabolic systems. Heterogeneity in stress and socioeconomic resource pathways was assessed using latent class analysis to identify clusters, or classes, of stress and socioeconomic resource trajectories. The influence of early socioeconomic adversity on young adults' physical health risk, as measured by biomarkers, was estimated, and the role of stress and socioeconomic resource trajectory classes as linking mechanisms was assessed. There was evidence for the influence of early socioeconomic adversity on young adults' physical health risk directly and indirectly through stress and socioeconomic resource trajectory classes over the early life course. These findings suggest that health models should be broadened to incorporate both stress and resource experiences simultaneously. Furthermore, these findings have prevention and intervention implications, including the importance of early socioeconomic adversity and key intervention points for "turning" the trajectories of at-risk youth.

Computing with spatial trajectories

CERN Document Server

2011-01-01

Covers the fundamentals and the state-of-the-art research inspired by the spatial trajectory data Readers are provided with tutorial-style chapters, case studies and references to other relevant research work This is the first book that presents the foundation dealing with spatial trajectories and state-of-the-art research and practices enabled by trajectories

Residual stresses in laser direct metal deposited Waspaloy

Energy Technology Data Exchange (ETDEWEB)

Moat, R.J., E-mail: richard.moat@manchester.ac.uk [School of Materials, University of Manchester, Grosvenor Street, Manchester M1 7HS (United Kingdom); Pinkerton, A.J.; Li, L. [Laser Processing Research Centre, School of Mechanical, Aerospace and Civil Engineering, University of Manchester, M60 1QD (United Kingdom); Withers, P.J.; Preuss, M. [School of Materials, University of Manchester, Grosvenor Street, Manchester M1 7HS (United Kingdom)

2011-03-15

Research highlights: {yields} Neutron diffraction and the contour method show good agreement. {yields} Tensile stresses found parallel to the surfaces. {yields} Compressive stresses within the bulk of the structures. {yields} Residual stress weakly dependent on the laser pulse parameters. {yields} Maximum tensile residual stress unaffected across range of pulse parameters used. - Abstract: This paper reports a study into the effect of laser pulse length and duty cycle on the residual stress distributions in multi-track laser direct metal deposits of Waspaloy onto an Inconel 718 substrate. The residual stresses have been evaluated using neutron diffraction and the contour method, while electron microscopy and micro hardness indentation have been used to map the concomitant microstructural variation. In all cases, near the tops of the deposited walls, the longitudinal stresses are tensile towards the mid-length of the wall, while the stresses perpendicular to the substrate are negligible. By contrast near the base of the walls, the stresses along the direction of deposition are small, while the stresses perpendicular to the substrate are compressive at the centre and tensile towards the ends. Consistent with previous observations, the stresses parallel to free surfaces are tensile, balanced by compressive stresses in the interior (an inverse quench stress profile). These profiles have been found to be weakly dependent on the laser pulse parameters, most notably an increase in tensile stress gradient with increasing duty cycle, but the maximum residual stresses are largely unaffected. Furthermore, microstructural analysis has shown that the effect of laser pulse parameters on grain morphology in multi-track thick walls is less marked than previously reported for single-track wall structures.

Residual stresses in laser direct metal deposited Waspaloy

International Nuclear Information System (INIS)

Moat, R.J.; Pinkerton, A.J.; Li, L.; Withers, P.J.; Preuss, M.

2011-01-01

Research highlights: → Neutron diffraction and the contour method show good agreement. → Tensile stresses found parallel to the surfaces. → Compressive stresses within the bulk of the structures. → Residual stress weakly dependent on the laser pulse parameters. → Maximum tensile residual stress unaffected across range of pulse parameters used. - Abstract: This paper reports a study into the effect of laser pulse length and duty cycle on the residual stress distributions in multi-track laser direct metal deposits of Waspaloy onto an Inconel 718 substrate. The residual stresses have been evaluated using neutron diffraction and the contour method, while electron microscopy and micro hardness indentation have been used to map the concomitant microstructural variation. In all cases, near the tops of the deposited walls, the longitudinal stresses are tensile towards the mid-length of the wall, while the stresses perpendicular to the substrate are negligible. By contrast near the base of the walls, the stresses along the direction of deposition are small, while the stresses perpendicular to the substrate are compressive at the centre and tensile towards the ends. Consistent with previous observations, the stresses parallel to free surfaces are tensile, balanced by compressive stresses in the interior (an inverse quench stress profile). These profiles have been found to be weakly dependent on the laser pulse parameters, most notably an increase in tensile stress gradient with increasing duty cycle, but the maximum residual stresses are largely unaffected. Furthermore, microstructural analysis has shown that the effect of laser pulse parameters on grain morphology in multi-track thick walls is less marked than previously reported for single-track wall structures.

Residual stress evaluation in brittle coatings using indentation technique combined with in-situ bending

International Nuclear Information System (INIS)

Futakawa, Masatoshi; Steinbrech, R.W.; Tanabe, Yuji; Hara, Toshiaki

2000-01-01

The indentation crack length approach was adopted and further elaborated to evaluate residual stress and toughness of the brittle coatings: two kinds of glass coatings on steel. The influence of the residual stress on indentation cracking was examined in as-received coating condition and by in-situ superimposing a counteracting tensile stress. For purpose of providing reference toughness values stress-free pieces of separated coating material have also been examined. Thus results of the two complementary sets of experiments were assumed to prove self-consistently toughness and residual stress data of the coating. In particular, the in-situ bending of specimen in combination with the indentation test allowed us to vary deliberately the residual stress situation in glass coating. Thus experiments which utilized the combination of bending test and micro-indentation were introduced as a method to provide unambiguous information about residual compressive stress. Toughness and residual compressive stress of glass coatings used in this study were 0.46-0.50 MPa·m 1/2 and 94-111 MPa, respectively. Furthermore, a thermoelastic calculation of the residual compressive stress was performed and it is found that the value of residual compressive stress at coating surface of specimen was 90-102 MPa. (author)

Modeling of coupled thermodynamic and geomechanical performance of underground compressed air energy storage in lined rock caverns

Energy Technology Data Exchange (ETDEWEB)

Rutqvist, Jonny; Kim, Hyung-Mok; Ryu, Dong-Woo; Synn, Joong-Ho; Song, Won-Kyong

2012-06-01

We applied coupled nonisothermal, multiphase fluid flow and geomechanical numerical modeling to study the coupled thermodynamic and geomechanical performance of underground compressed air energy storage (CAES) in concrete-lined rock caverns. The paper focuses on CAES in lined caverns at relatively shallow depth (e.g., 100 m depth) in which a typical CAES operational pressure of 5 to 8 MPa is significantly higher than both ambient fluid pressure and in situ stress. We simulated a storage operation that included cyclic compression and decompression of air in the cavern, and investigated how pressure, temperature and stress evolve over several months of operation. We analyzed two different lining options, both with a 50 cm thick low permeability concrete lining, but in one case with an internal synthetic seal such as steel or rubber. For our simulated CAES system, the thermodynamic analysis showed that 96.7% of the energy injected during compression could be recovered during subsequent decompression, while 3.3% of the energy was lost by heat conduction to the surrounding media. Our geomechanical analysis showed that tensile effective stresses as high as 8 MPa could develop in the lining as a result of the air pressure exerted on the inner surface of the lining, whereas thermal stresses were relatively smaller and compressive. With the option of an internal synthetic seal, the maximum effective tensile stress was reduced from 8 to 5 MPa, but was still in substantial tension. We performed one simulation in which the tensile tangential stresses resulted in radial cracks and air leakage though the lining. This air leakage, however, was minor (about 0.16% of the air mass loss from one daily compression) in terms of CAES operational efficiency, and did not significantly impact the overall energy balance of the system. However, despite being minor in terms of energy balance, the air leakage resulted in a distinct pressure increase in the surrounding rock that could be

Identifying Trajectories of Borderline Personality Features in Adolescence: Antecedent and Interactive Risk Factors.

Science.gov (United States)

Haltigan, John D; Vaillancourt, Tracy

2016-03-01

To examine trajectories of adolescent borderline personality (BP) features in a normative-risk cohort (n = 566) of Canadian children assessed at ages 13, 14, 15, and 16 and childhood predictors of trajectory group membership assessed at ages 8, 10, 11, and 12. Data were drawn from the McMaster Teen Study, an on-going study examining relations among bullying, mental health, and academic achievement. Participants and their parents completed a battery of mental health and peer relations questionnaires at each wave of the study. Academic competence was assessed at age 8 (Grade 3). Latent class growth analysis, analysis of variance, and logistic regression were used to analyze the data. Three distinct BP features trajectory groups were identified: elevated or rising, intermediate or stable, and low or stable. Parent- and child-reported mental health symptoms, peer relations risk factors, and intra-individual risk factors were significant predictors of elevated or rising and intermediate or stable trajectory groups. Child-reported attention-deficit hyperactivity disorder (ADHD) and somatization symptoms uniquely predicted elevated or rising trajectory group membership, whereas parent-reported anxiety and child-reported ADHD symptoms uniquely predicted intermediate or stable trajectory group membership. Child-reported somatization symptoms was the only predictor to differentiate the intermediate or stable and elevated or rising trajectory groups (OR 1.15, 95% CI 1.04 to 1.28). Associations between child-reported reactive temperament and elevated BP features trajectory group membership were 10.23 times higher among children who were bullied, supporting a diathesis-stress pathway in the development of BP features for these youth. Findings demonstrate the heterogeneous course of BP features in early adolescence and shed light on the potential prodromal course of later borderline personality disorder. © The Author(s) 2015.

Geological background of the estimation of natural stresses in soil body

Directory of Open Access Journals (Sweden)

Chernyshev Sergey Nikolaevich

2015-01-01

Full Text Available Initial and boundary conditions are always given for solving the problem of calculating the interaction of tunnels and other underground structures with soil and rocks. The same conditions are set for calculating the surface buildings. These initial data for calculation are divided into three groups: 1 the geometrical shape of the layers of rocks (geological structure; 2 the parameters of the strength and compressibility of rocks; 3 compressive stresses in the array. These data all over the world are set with engineering surveys. In engineering surveys there are good methods of determining the source of the data 1 and 2. But there is no available methodology for determining the natural stress state. Therefore, compressive and tensile stresses are usually determined by mathematical modeling. The calculation of the compressive stresses is done on the basis of the following hypotheses: compressive stresses are created by the weight of rocks; they go down in proportion to the density of rocks; the main normal stress is has a vertical direction; normal stress in horizontal direction is smaller. The value of the horizontal stress is was calculated using Poisson’s ratio. This hypothesis of the nineteenth century was used another 50 years ago, when it was not known exactly about the movement of the continents and when compressive stresses in the earth’s crust have not yet been measured. Today a universal application of this hypothesis is not correct. Now the application of this hypothesis in many cases is not correct. In this research paper an attempt is made to specify the area, in which the above hypothesis can be used. This is done on the basis of current scientific evidence. Abroad this way of calculating tunnels and other underground structures and bases of buildings should be done taking into account the real field of natural stresses. The geological characteristics of the location of the axes of stresses in soil body are based on the study of

Exposure to stressors and trajectories of perceived stress among older adults.

Science.gov (United States)

Vasunilashorn, Sarinnapha; Lynch, Scott M; Glei, Dana A; Weinstein, Maxine; Goldman, Noreen

2015-03-01

Models of stress incorporate both the environmental demands experienced by individuals (stressors) and the appraisal of these life events (perceptions). Because little is known about the extent to which experience and perceptions are related, we examine this relationship in a nationally representative population of older Taiwanese adults. Using growth models applied to data from 3 waves (1999, 2003, and 2007) of the Taiwan Longitudinal Study of Aging, we (a) investigate patterns of change in perceived stress in later adulthood and (b) examine how experienced stressors influence perceived stress. Participants were asked to report the presence of, and in some cases the degree of, exposure to stressors including total number of medical conditions, difficulty with activities of daily living, difficulty with mobility functions, being financially worse off compared with the prior wave, experiencing the death of a child, and experiencing a marital disruption. Items reflecting perceived stress included concerns about various domains pertaining to the respondent and his/her family member. Our results indicate that exposure to stressors increases, whereas perceived stress decreases, over time. Change in exposure to stressors is not generally associated with change in perceptions of stress, with the exception of a summary measure of health-related exposure to stressors. An increase in poor health over time is related to an increase in perceived stress in all domains. The results underscore the importance of distinguishing between perceptions of stress and exposure to stressors when studying the links between stress and health among older adults. Furthermore, the diminishing linkage between experienced stressors and perceptions of stress suggests that older adults' appraisal may be an adaptive coping strategy that emerges to buffer some of the difficulties that are inevitable in later life. © The Author 2014. Published by Oxford University Press on behalf of The

Comparative data compression techniques and multi-compression results

International Nuclear Information System (INIS)

Hasan, M R; Ibrahimy, M I; Motakabber, S M A; Ferdaus, M M; Khan, M N H

2013-01-01

Data compression is very necessary in business data processing, because of the cost savings that it offers and the large volume of data manipulated in many business applications. It is a method or system for transmitting a digital image (i.e., an array of pixels) from a digital data source to a digital data receiver. More the size of the data be smaller, it provides better transmission speed and saves time. In this communication, we always want to transmit data efficiently and noise freely. This paper will provide some compression techniques for lossless text type data compression and comparative result of multiple and single compression, that will help to find out better compression output and to develop compression algorithms

Neurofilaments Function as Shock Absorbers: Compression Response Arising from Disordered Proteins

Science.gov (United States)

Kornreich, Micha; Malka-Gibor, Eti; Zuker, Ben; Laser-Azogui, Adi; Beck, Roy

2016-09-01

What can cells gain by using disordered, rather than folded, proteins in the architecture of their skeleton? Disordered proteins take multiple coexisting conformations, and often contain segments which act as random-walk-shaped polymers. Using x-ray scattering we measure the compression response of disordered protein hydrogels, which are the main stress-responsive component of neuron cells. We find that at high compression their mechanics are dominated by gaslike steric and ionic repulsions. At low compression, specific attractive interactions dominate. This is demonstrated by the considerable hydrogel expansion induced by the truncation of critical short protein segments. Accordingly, the floppy disordered proteins form a weakly cross-bridged hydrogel, and act as shock absorbers that sustain large deformations without failure.

On the compression behaviour of the Callovo-Oxfordian argillite

International Nuclear Information System (INIS)

Mohajerani, M.; Delage, P.; Monfared, M.; Sulem, J.; Tang, A.M.; Schroeder, C.

2010-01-01

Document available in extended abstract form only. In the framework of research into radioactive waste disposal, it was decided to investigate some aspects of the volume change behaviour of the Callovo-Oxfordian argillite, a possible host rock in which the ANDRA underground laboratory of Bure (East of France) has been excavated. To do so, high pressure oedometers able to apply a maximum load of 113 MPa were used. Oedometers are widely used in Soil mechanics but not so much in Rock mechanics. In spite of applying combined stress/strain conditions (controlled vertical stress with no radial strain allowed) in which the radial stress is not controlled, their advantage is to be simple and robust to use (easy long term stress control and strain measurements). They provide a simple way to investigate the elastoplastic behaviour of soils, particularly regarding the elastic modulus, yield point and plastic compressibility. A high pressure oedometer developed at UR Navier/CERMES was used. The apparatus is a double lever arm device able to apply a maximum axial stress of 113 MPa on a specimen contained in a rigid ring of diameter 38 mm. The sample is 10 mm high. Vertical strains are monitored by using an electronic strain transducer connected to a data acquisition system. Previous calibration of the system was carried out by running a test with no sample in the ring so as to account for the effects of the compression of the top and bottom porous disks, of cell and of the piston. A reversible response of the system was observed after applying various loading cycles between 0 and 113 MPa. The specimen was trimmed by using a diamond corer of corresponding diameter and placed inside the oedometer ring. The top and bottom faces of the sample were polished by using sand paper so as to get two flat, regular and parallel faces. The ring was placed into the oedometer cell with dry porous stones and specimen was loaded under 1 MPa to ensure good contact with the porous stones and the

Phase transitions during compression and decompression of clots from platelet-poor plasma, platelet-rich plasma and whole blood.

Science.gov (United States)

Liang, Xiaojun; Chernysh, Irina; Purohit, Prashant K; Weisel, John W

2017-09-15

Blood clots are required to stem bleeding and are subject to a variety of stresses, but they can also block blood vessels and cause heart attacks and ischemic strokes. We measured the compressive response of human platelet-poor plasma (PPP) clots, platelet-rich plasma (PRP) clots and whole blood clots and correlated these measurements with confocal and scanning electron microscopy to track changes in clot structure. Stress-strain curves revealed four characteristic regions, for compression-decompression: (1) linear elastic region; (2) upper plateau or softening region; (3) non-linear elastic region or re-stretching of the network; (4) lower plateau in which dissociation of some newly made connections occurs. Our experiments revealed that compression proceeds by the passage of a phase boundary through the clot separating rarefied and densified phases. This observation motivates a model of fibrin mechanics based on the continuum theory of phase transitions, which accounts for the pre-stress caused by platelets, the adhesion of fibrin fibers in the densified phase, the compression of red blood cells (RBCs), and the pumping of liquids through the clot during compression/decompression. Our experiments and theory provide insights into the mechanical behavior of blood clots that could have implications clinically and in the design of fibrin-based biomaterials. The objective of this paper is to measure and mathematically model the compression behavior of various human blood clots. We show by a combination of confocal and scanning electron microscopy that compression proceeds by the passage of a front through the sample that separates a densified region of the clot from a rarefied region, and that the compression/decompression response is reversible with hysteresis. These observations form the basis of a model for the compression response of clots based on the continuum theory of phase transitions. Our studies may reveal how clot rheology under large compression in vivo due

Failure Mechanisms of Brittle Rocks under Uniaxial Compression

Science.gov (United States)

Liu, Taoying; Cao, Ping

2017-09-01

The behaviour of a rock mass is determined not only by the properties of the rock matrix, but mostly by the presence and properties of discontinuities or fractures within the mass. The compression test on rock-like specimens with two prefabricated transfixion fissures, made by pulling out the embedded metal inserts in the pre-cured period was carried out on the servo control uniaxial loading tester. The influence of the geometry of pre-existing cracks on the cracking processes was analysed with reference to the experimental observation of crack initiation and propagation from pre-existing flaws. Based on the rock fracture mechanics and the stress-strain curves, the evolution failure mechanism of the fissure body was also analyzed on the basis of exploring the law of the compression-shear crack initiation, wing crack growth and rock bridge connection. Meanwhile, damage fracture mechanical models of a compression-shear rock mass are established when the rock bridge axial transfixion failure, tension-shear combined failure, or wing crack shear connection failure occurs on the specimen under axial compression. This research was of significance in studying the failure mechanism of fractured rock mass.

Generic trajectory representation and trajectory following for wheeled robots

DEFF Research Database (Denmark)

Kjærgaard, Morten; Andersen, Nils Axel; Ravn, Ole

2014-01-01

will drive. Safe: Avoid fatal collisions. Based on a survey of existing methods and algorithms the article presents a generic way to represent constraints for different types of robots, a generic way to represent trajectories using Bëzier curves, a method to convert the trajectory so it can be driven...... in a smooth motion, a method to create a safe velocity profile for the robot, and a path following controller....

Temperature dependence of residual stress in TiC coated Mo

International Nuclear Information System (INIS)

Yoshizawa, I.; Fukutomi, M.; Kamada, K.

1984-01-01

The effects of fabrication temperature and heat treatment on the residual stress in TiC coated Mo have been studied by using X-ray diffractometry. TiC coatings on Mo single crystal substrates with (100) and (111) surfaces were carried out with the Activated Reactive Evaporation (ARE) method. It was found that all Mo substrates measured show tensile residual stresses, and their values decrease as the fabrication temperature increases from 300 to 700 0 C. On the other hand, TiC films measured showed compressive residual stresses, for both TiC/Mo(100) and TiC/Mo(111) specimens. These compressive stresses also decreased with increasing the fabrication temperature. The residual stresses measured were higher in TiC/Mo(100) than in TiC/Mo(111). It was found that the compressive stresses in as-grown TiC films change to the tensile stresses after annealing at 1700 0 C for 30 min. The preferred orientations of TiC films were observed to depend on the fabrication temperature. However, no epitaxial growth of TiC films was found as far as the present experiment was concerned. (orig.)

Relation Between Residual and Hoop Stresses and Rolling Bearing Fatigue Life

Science.gov (United States)

Oswald, Fred B.; Zaretsky, Erwin V.; Poplawski, Joseph V.

2015-01-01

Rolling-element bearings operated at high speed or high vibration may require a tight interference fit between the bore of the bearing and shaft to prevent rotation of the bearing bore around the shaft and fretting damage at the interfaces. Previous work showed that the hoop stresses resulting from tight interference fits can reduce bearing lives by as much as 65 percent. Where tight interference fits are required, case-carburized steel such as AISI 9310 or M50 NiL is often used because the compressive residual stresses inhibit subsurface crack formation and the ductile core inhibits inner-ring fracture. The presence of compressive residual stress and its combination with hoop stress also modifies the Hertz stress-life relation. This paper analyzes the beneficial effect of residual stresses on rolling-element bearing fatigue life in the presence of high hoop stresses for three bearing steels. These additional stresses were superimposed on Hertzian principal stresses to calculate the inner-race maximum shearing stress and the resulting fatigue life of the bearing. The load-life exponent p and Hertz stress-life exponent n increase in the presence of compressive residual stress, which yields increased life, particularly at lower stress levels. The Zaretsky life equation is described and is shown to predict longer bearing lives and greater load- and stress-life exponents, which better predicts observed life of bearings made from vacuum-processed steel.

Finite element analysis of maxillary bone stress caused by Aramany Class IV obturator prostheses.

Science.gov (United States)

Miyashita, Elcio Ricardo; Mattos, Beatriz Silva Câmara; Noritomi, Pedro Yoshito; Navarro, Hamilton

2012-05-01

The retention of an Aramany Class IV removable partial dental prosthesis can be compromised by a lack of support. The biomechanics of this obturator prosthesis result in an unusual stress distribution on the residual maxillary bone. This study evaluated the biomechanics of an Aramany Class IV obturator prosthesis with finite element analysis and a digital 3-dimensional (3-D) model developed from a computed tomography scan; bone stress was evaluated according to the load placed on the prosthesis. A 3-D model of an Aramany Class IV maxillary resection and prosthesis was constructed. This model was used to develop a finite element mesh. A 120 N load was applied to the occlusal and incisal platforms corresponding to the prosthetic teeth. Qualitative analysis was based on the scale of maximum principal stress; values obtained through quantitative analysis were expressed in MPa. Under posterior load, tensile and compressive stresses were observed; the tensile stress was greater than the compressive stress, regardless of the bone region, and the greatest compressive stress was observed on the anterior palate near the midline. Under an anterior load, tensile stress was observed in all of the evaluated bone regions; the tensile stress was greater than the compressive stress, regardless of the bone region. The Aramany Class IV obturator prosthesis tended to rotate toward the surgical resection when subjected to posterior or anterior loads. The amount of tensile and compressive stress caused by the Aramany Class IV obturator prosthesis did not exceed the physiological limits of the maxillary bone tissue. (J Prosthet Dent 2012;107:336-342). Copyright © 2012 The Editorial Council of the Journal of Prosthetic Dentistry. Published by Mosby, Inc. All rights reserved.

Compressive Fatigue in Wood

DEFF Research Database (Denmark)

Clorius, Christian Odin; Pedersen, Martin Bo Uhre; Hoffmeyer, Preben

1999-01-01

An investigation of fatigue failure in wood subjected to load cycles in compression parallel to grain is presented. Small clear specimens of spruce are taken to failure in square wave formed fatigue loading at a stress excitation level corresponding to 80% of the short term strength. Four...... frequencies ranging from 0.01 Hz to 10 Hz are used. The number of cycles to failure is found to be a poor measure of the fatigue performance of wood. Creep, maximum strain, stiffness and work are monitored throughout the fatigue tests. Accumulated creep is suggested identified with damage and a correlation...

The one-dimensional compression method for extraction of pore water from unsaturated tuff and effects on pore-water chemistry

Energy Technology Data Exchange (ETDEWEB)

Higgins, J.D.; Burger, P.A. [Colorado School of Mines, Golden, CO (United States); Yang, L.C. [Geological Survey, Denver, CO (United States)

1997-12-31

Study of the hydrologic system at Yucca Mountain, Nevada, requires extraction of pore-water samples from unsaturated tuff bedrock. Two generations of compression cells have been designed and tested for extracting representative, unaltered pore-water samples from unsaturated tuff cores. The one-dimensional compression cell has a maximum compressive stress rating of 552 MPa. Results from 86 tests show that the minimum degree of saturation for successful extraction of pore water was about 14% for non welded tuff and about 61% for densely welded tuff. The high-pressure, one-dimensional compression cell has a maximum compressive stress rating of 827 MPa. Results from 109 tests show that the minimum degree of saturation for successful extraction of pore water was about 7.5% for non welded tuff and about 34% for densely welded tuff. Geochemical analyses show that, in general, there is a decrease in ion concentration of pore waters as extraction pressures increase. Only small changes in pore-water composition occur during the one-dimensional extraction test.

Mechanical behavior and dynamic failure of high-strength ultrafine grained tungsten under uniaxial compression

International Nuclear Information System (INIS)

Wei, Q.; Jiao, T.; Ramesh, K.T.; Ma, E.; Kecskes, L.J.; Magness, L.; Dowding, R.; Kazykhanov, V.U.; Valiev, R.Z.

2006-01-01

We have systematically investigated the quasi-static and dynamic mechanical behavior (especially dynamic failure) of ultra-fine grained (UFG) tungsten (W) under uniaxial compression. The starting material is of commercial purity and large grain size. We utilized severe plastic deformation to achieve the ultrafine microstructure characterized by grains and subgrains with sizes of ∼500 nm, as identified by transmission electron microscopy. Results of quasi-static compression show that the UFG W behaves in an elastic-nearly perfect plastic manner (i.e., vanishing strain hardening), with its flow stress approaching 2 GPa, close to twice that of conventional coarse grain W. Post-mortem examinations of the quasi-statically loaded samples show no evidence of cracking, in sharp contrast to the behavior of conventional W (where axial cracking is usually observed). Under uniaxial dynamic compression (strain rate ∼10 3 s -1 ), the true stress-true strain curves of the UFG W exhibit significant flow softening, and the peak stress is ∼3 GPa. Furthermore, the strain rate sensitivity of the UFG W is reduced to half the value of the conventional W. Both in situ high-speed photography and post-mortem examinations reveal shear localization and as a consequence, cracking of the UFG W under dynamic uniaxial compression. These observations are consistent with recent observations on other body-centered cubic metals with nanocrystalline or ultrafine microstructures. The experimental results are discussed using existing models for adiabatic shear localization in metals

Efficient Lossy Compression for Compressive Sensing Acquisition of Images in Compressive Sensing Imaging Systems

Directory of Open Access Journals (Sweden)

Xiangwei Li

2014-12-01

Full Text Available Compressive Sensing Imaging (CSI is a new framework for image acquisition, which enables the simultaneous acquisition and compression of a scene. Since the characteristics of Compressive Sensing (CS acquisition are very different from traditional image acquisition, the general image compression solution may not work well. In this paper, we propose an efficient lossy compression solution for CS acquisition of images by considering the distinctive features of the CSI. First, we design an adaptive compressive sensing acquisition method for images according to the sampling rate, which could achieve better CS reconstruction quality for the acquired image. Second, we develop a universal quantization for the obtained CS measurements from CS acquisition without knowing any a priori information about the captured image. Finally, we apply these two methods in the CSI system for efficient lossy compression of CS acquisition. Simulation results demonstrate that the proposed solution improves the rate-distortion performance by 0.4~2 dB comparing with current state-of-the-art, while maintaining a low computational complexity.

Hydralazine inhibits compression and acrolein-mediated injuries in ex vivo spinal cord.

Science.gov (United States)

Hamann, Kristin; Nehrt, Genevieve; Ouyang, Hui; Duerstock, Brad; Shi, Riyi

2008-02-01

We have previously shown that acrolein, a lipid peroxidation byproduct, is significantly increased following spinal cord injury in vivo, and that exposure to neuronal cells results in oxidative stress, mitochondrial dysfunction, increased membrane permeability, impaired axonal conductivity, and eventually cell death. Acrolein thus may be a key player in the pathogenesis of spinal cord injury, where lipid peroxidation is known to be involved. The current study demonstrates that the acrolein scavenger hydralazine protects against not only acrolein-mediated injury, but also compression in guinea pig spinal cord ex vivo. Specifically, hydralazine (500 mumol/L to 1 mmol/L) can significantly alleviate acrolein (100-500 mumol/L)-induced superoxide production, glutathione depletion, mitochondrial dysfunction, loss of membrane integrity, and reduced compound action potential conduction. Additionally, 500 mumol/L hydralazine significantly attenuated compression-mediated membrane disruptions at 2 and 3 h following injury. This was consistent with our findings that acrolein-lys adducts were increased following compression injury ex vivo, an effect that was prevented by hydralazine treatment. These findings provide further evidence for the role of acrolein in spinal cord injury, and suggest that acrolein-scavenging drugs such as hydralazine may represent a novel therapy to effectively reduce oxidative stress in disorders such as spinal cord injury and neurodegenerative diseases, where oxidative stress is known to play a role.

Child anxiety symptoms related to longitudinal cortisol trajectories and acute stress responses: evidence of developmental stress sensitization.

Science.gov (United States)

Laurent, Heidemarie K; Gilliam, Kathryn S; Wright, Dorianne B; Fisher, Philip A

2015-02-01

Cross-sectional research suggests that individuals at risk for internalizing disorders show differential activation levels and/or dynamics of stress-sensitive physiological systems, possibly reflecting a process of stress sensitization. However, there is little longitudinal research to clarify how the development of these systems over time relates to activation during acute stress, and how aspects of such activation map onto internalizing symptoms. We investigated children's (n = 107) diurnal hypothalamic-pituitary-adrenal activity via salivary cortisol (morning and evening levels) across 29 assessments spanning 6+ years, and related longitudinal patterns to acute stress responses at the end of this period (age 9-10). Associations with child psychiatric symptoms at age 10 were also examined to determine internalizing risk profiles. Increasing morning cortisol levels across assessments predicted less of a cortisol decline following interpersonal stress at age 9, and higher cortisol levels during performance stress at age 10. These same profiles of high and/or sustained cortisol elevation during psychosocial stress were associated with child anxiety symptoms. Results suggest developmental sensitization to stress-reflected in rising morning cortisol and eventual hyperactivation during acute stress exposure-may distinguish children at risk for internalizing disorders. (PsycINFO Database Record (c) 2015 APA, all rights reserved).

Evolution of microstructure and residual stress on L1{sub 0} ordering in FePt thin films with different initial stress states

Energy Technology Data Exchange (ETDEWEB)

Hsiao, S.N., E-mail: pmami.hsiao@gmail.com [Department of Materials Science and Engineering, Feng Chia University, Taichung 407, Taiwan (China); Yuan, F.T. [iSentek Ltd., Advanced Sensor Laboratory, New Taipei City 221, Taiwan (China); Chen, S.K. [Department of Materials Science and Engineering, Feng Chia University, Taichung 407, Taiwan (China); Sun, A.C. [Department of Chemical Engineering and Materials Science, Yuan Ze University, Jungli 320, Taiwan (China); Su, S.H.; Chiu, K.F. [Department of Materials Science and Engineering, Feng Chia University, Taichung 407, Taiwan (China)

2016-01-15

We have characterized the dependence of microstructure, and internal strain/stress on L1{sub 0} ordering in 40 nm thick FePt films with different initial stresses. The microstructural and crystallographic results indicate that defect annihilation and grain growth induced an increase in tensile stress of ~1 GPa before extensive L1{sub 0} ordering. The induced tensile stress can efficiently facilitate the nucleation of L1{sub 0} phase owing to that the volume expansion of L1{sub 0} ordering and atomic rearrangement neutralizes the tensile stress. If the as-deposited FePt film has a highly compressive state, the induced tensile stress will be canceled out and ordering is retarded, which results in a higher ordering temperature. - Highlights: • Microstructure-stress connection in FePt films was studied. • Initial stress alters microstructure and stress evolution during annealing. • Densification induces tensile stress of ~1 GPa before extensive L1{sub 0} ordering. • Induced tensile stress can efficiently facilitate the nucleation of L1{sub 0} phase. • Compressively initial stress results in a higher ordering temperature .

Stress envelope of silicon carbide composites at elevated temperatures

International Nuclear Information System (INIS)

Nozawa, Takashi; Kim, Sunghun; Ozawa, Kazumi; Tanigawa, Hiroyasu

2014-01-01

To identify a comprehensive stress envelope, i.e., strength anisotropy map, of silicon carbide fiber-reinforced silicon carbide matrix composite (SiC/SiC composite) for practical component design, tensile and compressive tests were conducted using the small specimen test technique specifically tailored for high-temperature use. In-plane shear properties were, however, estimated using the off-axial tensile method and assuming that the mixed mode failure criterion, i.e., Tsai–Wu criterion, is valid for the composites. The preliminary test results indicate no significant degradation to either proportional limit stress (PLS) or fracture strength by tensile loading at temperatures below 1000 °C. A similarly good tolerance of compressive properties was identified at elevated temperatures, except for a slight degradation in PLS. With the high-temperature test data of tensile, compressive and in-plane shear properties, the stress envelopes at elevated temperatures were finally obtained. A slight reduction in the design limit was obvious at elevated temperatures when the compressive mode is dominant, whereas a negligibly small impact on the design is expected by considering the tensile loading case

Stress envelope of silicon carbide composites at elevated temperatures

Energy Technology Data Exchange (ETDEWEB)

Nozawa, Takashi, E-mail: nozawa.takashi67@jaea.go.jp [Japan Atomic Energy Agency, 2-166 Omotedate, Obuchi, Rokkasho, Aomori 039-3212 (Japan); Kim, Sunghun [Graduate School of Energy Science, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Ozawa, Kazumi; Tanigawa, Hiroyasu [Japan Atomic Energy Agency, 2-166 Omotedate, Obuchi, Rokkasho, Aomori 039-3212 (Japan)

2014-10-15

To identify a comprehensive stress envelope, i.e., strength anisotropy map, of silicon carbide fiber-reinforced silicon carbide matrix composite (SiC/SiC composite) for practical component design, tensile and compressive tests were conducted using the small specimen test technique specifically tailored for high-temperature use. In-plane shear properties were, however, estimated using the off-axial tensile method and assuming that the mixed mode failure criterion, i.e., Tsai–Wu criterion, is valid for the composites. The preliminary test results indicate no significant degradation to either proportional limit stress (PLS) or fracture strength by tensile loading at temperatures below 1000 °C. A similarly good tolerance of compressive properties was identified at elevated temperatures, except for a slight degradation in PLS. With the high-temperature test data of tensile, compressive and in-plane shear properties, the stress envelopes at elevated temperatures were finally obtained. A slight reduction in the design limit was obvious at elevated temperatures when the compressive mode is dominant, whereas a negligibly small impact on the design is expected by considering the tensile loading case.

30 CFR 75.1730 - Compressed air; general; compressed air systems.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Compressed air; general; compressed air systems... Compressed air; general; compressed air systems. (a) All pressure vessels shall be constructed, installed... Safety and Health district office. (b) Compressors and compressed-air receivers shall be equipped with...

Tension-Compression Fatigue Behavior of Plain Woven Kenaf/Kevlar Hybrid Composites

Directory of Open Access Journals (Sweden)

Suhad D. Salman

2016-02-01

Full Text Available The applications of hybrid natural/synthetic reinforced polymer composites have been rapidly gaining market share in structural applications due to their remarkable characteristics and the fact that most of the components made of these materials are subjected to cyclic loading. Their fatigue properties have received a lot of attention because predicting their behavior is a challenge due to the effects of the synergies between the fibers. The purpose of this work is to characterize the tension, compression, and tensile-compression fatigue behavior of six layers of Kevlar hybridized with one layer of woven kenaf reinforced epoxy, at a 35% weight fraction. Fatigue tests were carried out and loaded cyclically at 60%, 70%, 80%, and 90% of their ultimate compressive stress. The results give a complete description for tensile and compression properties and could be used to predict fatigue-induced failure mechanisms.

X-ray study of residual stress distribution of ground ceramics

International Nuclear Information System (INIS)

Sakaida, Yoshihisa; Tanaka, Keisuke; Ikuhara, Yuichi; Suzuki, Kenzi.

1997-01-01

The residual stress distribution of ground ceramics was determined from the eigen strain existing in the ground surface. The eigen strain of ground ceramics was tensile, and exponentially decreased with the distance from the surface. The residual stress distribution is given as a superposition of an exponential function of compression and a linear function. It is found that the actual residual stress distribution can be approximated by a compressive exponential function because the magnitude of tensile residual stress is negligibly small compared to the compressive residual stress. In the experiments, the diffraction angle was measured on ground silicon nitride for a wide range of sin 2 ψ using the glancing incidence X-ray diffraction technique. A strong nonlinearity was found in the 2θ-sin 2 ψ diagram at very high ψ-angles. From the analysis of nonlinearity, the residual stress distribution was determined. The residual stress distribution of silicon nitride coincided with the distribution calculated from the eigen strain distribution. Transmission electron microscopy was used to clarify the origin of generation of the residual stress. Both strain contrasts and microcracks were observed below the ground surface ; straight dislocations were also observed within silicon nitride grains near the ground surface. (author)

Strain-dependent dynamic compressive properties of magnetorheological elastomeric foams

Science.gov (United States)

Wereley, Norman M.; Perez, Colette; Choi, Young T.

2018-05-01

This paper addresses the strain-dependent dynamic compressive properties (i.e., so-called Payne effect) of magnetorheological elastomeric foams (MREFs). Isotropic MREF samples (i.e., no oriented particle chain structures), fabricated in flat square shapes (nominal size of 26.5 mm x 26.5 mm x 9.5 mm) were synthesized by randomly dispersing micron-sized iron oxide particles (Fe3O4) into a liquid silicone foam in the absence of magnetic field. Five different Fe3O4 particle concentrations of 0, 2.5, 5.0, 7.5, and 10 percent by volume fraction (hereinafter denoted as vol%) were used to investigate the effect of particle concentration on the dynamic compressive properties of the MREFs. The MREFs were sandwiched between two multi-pole flexible plate magnets in order to activate the magnetorheological (MR) strengthening effect. Under two different pre-compression conditions (i.e., 35% and 50%), the dynamic compressive stresses of the MREFs with respect to dynamic strain amplitudes (i.e., 1%-10%) were measured by using a servo-hydraulic testing machine. The complex modulus (i.e., storage modulus and loss modulus) and loss factors of the MREFs with respect to dynamic strain amplitudes were presented as performance indices to evaluate their strain-dependent dynamic compressive behavior.

Strain-dependent dynamic compressive properties of magnetorheological elastomeric foams

Directory of Open Access Journals (Sweden)

Norman M. Wereley

2018-05-01

Full Text Available This paper addresses the strain-dependent dynamic compressive properties (i.e., so-called Payne effect of magnetorheological elastomeric foams (MREFs. Isotropic MREF samples (i.e., no oriented particle chain structures, fabricated in flat square shapes (nominal size of 26.5 mm x 26.5 mm x 9.5 mm were synthesized by randomly dispersing micron-sized iron oxide particles (Fe3O4 into a liquid silicone foam in the absence of magnetic field. Five different Fe3O4 particle concentrations of 0, 2.5, 5.0, 7.5, and 10 percent by volume fraction (hereinafter denoted as vol% were used to investigate the effect of particle concentration on the dynamic compressive properties of the MREFs. The MREFs were sandwiched between two multi-pole flexible plate magnets in order to activate the magnetorheological (MR strengthening effect. Under two different pre-compression conditions (i.e., 35% and 50%, the dynamic compressive stresses of the MREFs with respect to dynamic strain amplitudes (i.e., 1%-10% were measured by using a servo-hydraulic testing machine. The complex modulus (i.e., storage modulus and loss modulus and loss factors of the MREFs with respect to dynamic strain amplitudes were presented as performance indices to evaluate their strain-dependent dynamic compressive behavior.

Size effect on compression properties of GaN nanocones examined using in situ transmission electron microscopy

International Nuclear Information System (INIS)

Kang, Shao-Hui; Fang, Te-Hua

2014-01-01

Highlights: • Strain-induced structural variations of GaN nanocones are estimated using in situ TEM. • Young’s modulus of GaN nanocones with a diameter of 100–350 nm are 190–290 GPa. • The E 2 peak was red-shifted, indicated increased compressive stress. - Abstract: Mechanical property measurements of single nanocones are challenging because the small scale of the nanostructures. In this study, critical-stress- and strain-induced structural variations of GaN nanocones are estimated using in situ transmission electron microscopy (TEM) compression experiments. For single GaN nanocones with a diameter of 100–350 nm, the Young’s modulus, plastic deformation energy (W p ), and elastic deformation energy (W e ) values were 190–290 GPa, 0.02–1.65 × 10 −11 J, and 0.04–3.85 × 10 −11 J, respectively. Raman spectra were used to measure GaN indentation. The E 2 peak was red-shifted, indicated increased compressive stress in the indented area

Autophagy is activated in compression-induced cell degeneration and is mediated by reactive oxygen species in nucleus pulposus cells exposed to compression.

Science.gov (United States)

Ma, K-G; Shao, Z-W; Yang, S-H; Wang, J; Wang, B-C; Xiong, L-M; Wu, Q; Chen, S-F

2013-12-01

To determine whether autophagy contributes to the pathogenesis of degenerative disc disease (DDD) or retards the intervertebral disc (IVD) degeneration, and investigate the possible relationship between compression-induced autophagy and intracellular reactive oxygen species (ROS) in nucleus pulposus (NP) cells in vitro. The autophagosome and autophagy-related markers were used to explore the role of autophagy in rat NP cells under compressive stress, which were measured directly by electronic microscopy, monodansylcadaverine (MDC) staining, immunofluorescence, western blot, and indirectly by analyzing the impact of pharmacological inhibitors of autophagy such as 3-methyladenine (3-MA) and chloroquine (CQ). And the relationship between autophagy and apoptosis was investigated by Annexin-V/propidium iodide (PI)-fluorescein staining. In addition, ROS were measured to determine whether these factors are responsible for the development of compression-induced autophagy. Our results indicated that rat NP cells activated autophagy in response to the same strong apoptotic stimuli that triggered apoptosis by compression. Autophagy and apoptosis were interconnected and coordinated in rat NP cells exposed to compression stimuli. Compression-induced autophagy was closely related to intracellular ROS production. Enhanced degradation of damaged components of NP cells by autophagy may be a crucial survival response against mechanical overload, and extensive autophagy may trigger autophagic cell death. Regulating autophagy and reducing the generation of intracellular ROS may retard IVD degeneration. Copyright © 2013 Osteoarthritis Research Society International. Published by Elsevier Ltd. All rights reserved.

Lunar and interplanetary trajectories

CERN Document Server

Biesbroek, Robin

2016-01-01

This book provides readers with a clear description of the types of lunar and interplanetary trajectories, and how they influence satellite-system design. The description follows an engineering rather than a mathematical approach and includes many examples of lunar trajectories, based on real missions. It helps readers gain an understanding of the driving subsystems of interplanetary and lunar satellites. The tables and graphs showing features of trajectories make the book easy to understand. .

Residual stress measurement in worked and heat treated steel by X-ray diffractometry

International Nuclear Information System (INIS)

Sinha, V.K.; Godaba, V.S.

2008-01-01

Investigations were made for residual stress measurement by X-ray diffractometry in the 1.14% C, 0.46% Mn, 0.16% Si, 0.11% S and 0.04% P steel samples subjected to inhomogeneous plastic deformation (cold upsetting in the range 7.7-21%), thermal gradient (quenching from 630 deg. C) and phase transformation (quenching from 850 deg. C), respectively. The results indicated that compressive residual stress at the surface increased in the samples with increasing deformation acquiring values in the range, -269.5 MPa to -374.7 MPa. In the samples quenched from 630 deg. C, the thermal stresses acquired increasing values in the range -83.9 MPa (compressive) to -188.1 MPa (compressive) with increased cooling rate. In the samples quenched from 850 deg. C, volume increase on account of austenite to martensite phase transformation ultimately dominated the thermal contraction resulting in residual stress at the surface from -329.3 MPa (compressive) to +61.7 MPa (tensile)

Optimal trajectories of aircraft and spacecraft

Science.gov (United States)

Miele, A.

1990-01-01

Work done on algorithms for the numerical solutions of optimal control problems and their application to the computation of optimal flight trajectories of aircraft and spacecraft is summarized. General considerations on calculus of variations, optimal control, numerical algorithms, and applications of these algorithms to real-world problems are presented. The sequential gradient-restoration algorithm (SGRA) is examined for the numerical solution of optimal control problems of the Bolza type. Both the primal formulation and the dual formulation are discussed. Aircraft trajectories, in particular, the application of the dual sequential gradient-restoration algorithm (DSGRA) to the determination of optimal flight trajectories in the presence of windshear are described. Both take-off trajectories and abort landing trajectories are discussed. Take-off trajectories are optimized by minimizing the peak deviation of the absolute path inclination from a reference value. Abort landing trajectories are optimized by minimizing the peak drop of altitude from a reference value. Abort landing trajectories are optimized by minimizing the peak drop of altitude from a reference value. The survival capability of an aircraft in a severe windshear is discussed, and the optimal trajectories are found to be superior to both constant pitch trajectories and maximum angle of attack trajectories. Spacecraft trajectories, in particular, the application of the primal sequential gradient-restoration algorithm (PSGRA) to the determination of optimal flight trajectories for aeroassisted orbital transfer are examined. Both the coplanar case and the noncoplanar case are discussed within the frame of three problems: minimization of the total characteristic velocity; minimization of the time integral of the square of the path inclination; and minimization of the peak heating rate. The solution of the second problem is called nearly-grazing solution, and its merits are pointed out as a useful

Semantic Enrichment of GPS Trajectories

NARCIS (Netherlands)

de Graaff, V.; van Keulen, Maurice; de By, R.A.

2012-01-01

Semantic annotation of GPS trajectories helps us to recognize the interests of the creator of the GPS trajectories. Automating this trajectory annotation circumvents the requirement of additional user input. To annotate the GPS traces automatically, two types of automated input are required: 1) a

Time of flight measurements of unirradiated and irradiated nuclear graphite under cyclic compressive load

Energy Technology Data Exchange (ETDEWEB)

Bodel, W., E-mail: william.bodel@hotmail.com [Nuclear Graphite Research Group, The University of Manchester (United Kingdom); Atkin, C. [Health and Safety Laboratory, Buxton (United Kingdom); Marsden, B.J. [Nuclear Graphite Research Group, The University of Manchester (United Kingdom)

2017-04-15

The time-of-flight technique has been used to investigate the stiffness of nuclear graphite with respect to the grade and grain direction. A loading rig was developed to collect time-of-flight measurements during cycled compressive loading up to 80% of the material's compressive strength and subsequent unloading of specimens along the axis of the applied stress. The transmission velocity (related to Young's modulus), decreased with increasing applied stress; and depending on the graphite grade and orientation, the modulus then increased, decreased or remained constant upon unloading. These tests were repeated while observing the microstructure during the load/unload cycles. Initial decreases in transmission velocity with compressive load are attributed to microcrack formation within filler and binder phases. Three distinct types of behaviour occur on unloading, depending on the grade, irradiation, and loading direction. These different behaviours can be explained in terms of the material microstructure observed from the microscopy performed during loading.

The influence of work-family conflict trajectories on self-rated health trajectories in Switzerland: a life course approach.

Science.gov (United States)

Cullati, Stéphane

2014-07-01

Self-rated health (SRH) trajectories tend to decline over a lifetime. Moreover, the Cumulative Advantage and Disadvantage (CAD) model indicates that SRH trajectories are known to consistently diverge along socioeconomic positions (SEP) over the life course. However, studies of working adults to consider the influence of work and family conflict (WFC) on SRH trajectories are scarce. We test the CAD model and hypothesise that SRH trajectories diverge over time according to socioeconomic positions and WFC trajectories accentuate this divergence. Using longitudinal data from the Swiss Household Panel (N = 2327 working respondents surveyed from 2004 to 2010), we first examine trajectories of SRH and potential divergence over time across age, gender, SEP and family status using latent growth curve analysis. Second, we assess changes in SRH trajectories in relation to changes in WFC trajectories and divergence in SRH trajectories according to gender, SEP and family status using parallel latent growth curve analysis. Three measures of WFC are used: exhaustion after work, difficulty disconnecting from work, and work interference in private family obligations. The results show that SRH trajectories slowly decline over time and that the rate of change is not influenced by age, gender or SEP, a result which does not support the CAD model. SRH trajectories are significantly correlated with exhaustion after work trajectories but not the other two WFC measures. When exhaustion after work trajectories are taken into account, SRH trajectories of higher educated people decline slower compared to less educated people, supporting the CAD hypothesis. Copyright © 2014 Elsevier Ltd. All rights reserved.

Evaluation of Full Reynolds Stress Turbulence Models in FUN3D

Science.gov (United States)

Dudek, Julianne C.; Carlson, Jan-Renee

2017-01-01

Full seven-equation Reynolds stress turbulence models are a relatively new and promising tool for todays aerospace technology challenges. This paper uses two stress-omega full Reynolds stress models to evaluate challenging flows including shock-wave boundary layer interactions, separation and mixing layers. The Wilcox and the SSGLRR full second-moment Reynolds stress models are evaluated for four problems: a transonic two-dimensional diffuser, a supersonic axisymmetric compression corner, a compressible planar shear layer, and a subsonic axisymmetric jet. Simulation results are compared with experimental data and results using the more commonly used Spalart-Allmaras (SA) one-equation and the Menter Shear Stress Transport (SST) two-equation models.

Effects of shot peening on the residual stress of welded SS400 steel

International Nuclear Information System (INIS)

Lee, Jong Man; Kim, Tae Hyung; Cheong, Seong Kyun; Lee, Seung Ho

2002-01-01

The fatigue life of structures is usually determined by welding zone. The tensile residual stress, which is induced by welding, reduces the fatigue life and fatigue strength of welded structures. If we remove the tensile residual stress or induce the compressive residual stress, the fatigue life of welded structures will be improved. The change of hardness and compressive residual stress of welded zone after shot peening was investigated in this paper. The results show that the hardness was increased by shot peening. The residual stress was reduced by shot peening

Intermittent pneumatic compression of legs increases microcirculation in distant skeletal muscle.

Science.gov (United States)

Liu, K; Chen, L E; Seaber, A V; Johnson, G W; Urbaniak, J R

1999-01-01

Intermittent pneumatic compression has been established as a method of clinically preventing deep vein thrombosis, but the mechanism has not been documented. This study observed the effects of intermittent pneumatic compression of legs on the microcirculation of distant skeletal muscle. The cremaster muscles of 80 male rats were exposed, a specially designed intermittent pneumatic-compression device was applied to both legs for 60 minutes, and the microcirculation of the muscles was assessed by measurement of the vessel diameter in three categories (10-20, 21-40, and 41-70 microm) for 120 minutes. The results showed significant vasodilation in arterial and venous vessels during the application of intermittent pneumatic compression, which disappeared after termination of the compression. The vasodilation reached a maximum 30 minutes after initiation of the compression and could be completely blocked by an inhibitor of nitric oxide synthase, NG-monomethyl-L-arginine (10 micromol/min). A 120-minute infusion of NG-monomethyl-L-arginine, beginning coincident with 60 minutes of intermittent pneumatic compression, resulted in a significant decrease in arterial diameter that remained at almost the same level after termination of the compression. The magnitude of the decrease in diameter in the group treated with intermittent pneumatic compression and NG-monomethyl-L-arginine was comparable with that in the group treated with NG-monomethyl-L-arginine alone. The results imply that the production of nitric oxide is involved in the positive influence of intermittent pneumatic compression on circulation. It is postulated that the rapid increase in venous velocity induced by intermittent pneumatic compression produces strong shear stress on the vascular endothelium, which stimulates an increased release of nitric oxide and thereby causes systemic vasodilation.

Kinematics, mechanics, and potential earthquake hazards for faults in Pottawatomie County, Kansas, USA

Science.gov (United States)

Ohlmacher, G.C.; Berendsen, P.

2005-01-01

Many stable continental regions have subregions with poorly defined earthquake hazards. Analysis of minor structures (folds and faults) in these subregions can improve our understanding of the tectonics and earthquake hazards. Detailed structural mapping in Pottawatomie County has revealed a suite consisting of two uplifted blocks aligned along a northeast trend and surrounded by faults. The first uplift is located southwest of the second. The northwest and southeast sides of these uplifts are bounded by northeast-trending right-lateral faults. To the east, both uplifts are bounded by north-trending reverse faults, and the first uplift is bounded by a north-trending high-angle fault to the west. The structural suite occurs above a basement fault that is part of a series of north-northeast-trending faults that delineate the Humboldt Fault Zone of eastern Kansas, an integral part of the Midcontinent Rift System. The favored kinematic model is a contractional stepover (push-up) between echelon strike-slip faults. Mechanical modeling using the boundary element method supports the interpretation of the uplifts as contractional stepovers and indicates that an approximately east-northeast maximum compressive stress trajectory is responsible for the formation of the structural suite. This stress trajectory suggests potential activity during the Laramide Orogeny, which agrees with the age of kimberlite emplacement in adjacent Riley County. The current stress field in Kansas has a N85??W maximum compressive stress trajectory that could potentially produce earthquakes along the basement faults. Several epicenters of seismic events (

In situ synchrotron X-ray diffraction of ferroelastic La0.8Ca0.2CoO3 ceramics during uniaxial compression

International Nuclear Information System (INIS)

Vullum, Per Erik; Mastin, Johann; Wright, Jonathan; Einarsrud, Mari-Ann; Holmestad, Randi; Grande, Tor

2006-01-01

Uniaxial compression of rhombohedral La 0.8 Ca 0.2 CoO 3 ceramics has been studied in situ using synchrotron X-ray diffraction. The intensities of Bragg reflections parallel and perpendicular to the stress field were simultaneously detected as a function of the stress. Reorientation of ferroelastic domains due to the uniaxial stress was demonstrated. With increasing stress the volume fraction of domains with the hexagonal c-axis parallel to the stress axis increased at the expense of domains with the c-axis perpendicular to the stress axis. The strain in the polycrystalline materials evolved unevenly with increasing stress due to crystallographic anisotropy. In energetically favourable domains with the c-axis parallel to the stress axis, the rhombohedral distortion from cubic symmetry increased, while the crystal structure became closer to cubic in domains with the c-axis perpendicular to the stress. Successive compression/decompression cycles to higher maximum stress resulted in a higher volume fraction of reoriented domains both at maximum stress and after decompression

Measurements of the tensile and compressive properties of micro-concrete used in the Winfrith missile impact experiments

International Nuclear Information System (INIS)

Wilson, P.A.

1982-10-01

Tests to determine the tensile and compressive properties of a micro-concrete mix are described. The material is a nominally 40MPa ultimate compressive strength concrete used in impact tests with scale models in the prediction of responses in prototype concrete structures. Compressive tests were intended to give complete stress-strain relationships beyond initial failure. Tensile properties were measured by the Brazilian splitting technique and direct tension dog-bone specimens for comparison reasons. (U.K.)

Is Seasonal Stress a Career Choice of Professional Accountants?

Science.gov (United States)

Cluskey, G. R., Jr.; Vaux, Alan C.

1997-01-01

Examines stressors on tax professionals during periods of relatively high stress and periods of low stress. Results indicate that the strongest stressor-strain relationship was for the group surveyed in January (high stress), indicating that workload compression contributes to seasonal occupational stress. Looks at implications for employee…

A coupled creep plasticity model for residual stress relaxation of a shot-peened nickel-based superalloy

Science.gov (United States)

Buchanan, Dennis J.; John, Reji; Brockman, Robert A.; Rosenberger, Andrew H.

2010-01-01

Shot peening is a commonly used surface treatment process that imparts compressive residual stresses into the surface of metal components. Compressive residual stresses retard initiation and growth of fatigue cracks. During component loading history, shot-peened residual stresses may change due to thermal exposure, creep, and cyclic loading. In these instances, taking full credit for compressive residual stresses would result in a nonconservative life prediction. This article describes a methodical approach for characterizing and modeling residual stress relaxation under elevated temperature loading, near and above the monotonic yield strength of INI 00. The model incorporates the dominant creep deformation mechanism, coupling between the creep and plasticity models, and effects of prior plastic strain to simulate surface treatment deformation.

New Regenerative Cycle for Vapor Compression Refrigeration

Energy Technology Data Exchange (ETDEWEB)

Mark J. Bergander

2005-08-29

The main objective of this project is to confirm on a well-instrumented prototype the theoretically derived claims of higher efficiency and coefficient of performance for geothermal heat pumps based on a new regenerative thermodynamic cycle as comparing to existing technology. In order to demonstrate the improved performance of the prototype, it will be compared to published parameters of commercially available geothermal heat pumps manufactured by US and foreign companies. Other objectives are to optimize the design parameters and to determine the economic viability of the new technology. Background (as stated in the proposal): The proposed technology closely relates to EERE mission by improving energy efficiency, bringing clean, reliable and affordable heating and cooling to the residential and commercial buildings and reducing greenhouse gases emission. It can provide the same amount of heating and cooling with considerably less use of electrical energy and consequently has a potential of reducing our nations dependence on foreign oil. The theoretical basis for the proposed thermodynamic cycle was previously developed and was originally called a dynamic equilibrium method. This theory considers the dynamic equations of state of the working fluid and proposes the methods for modification of T-S trajectories of adiabatic transformation by changing dynamic properties of gas, such as flow rate, speed and acceleration. The substance of this proposal is a thermodynamic cycle characterized by the regenerative use of the potential energy of two-phase flow expansion, which in traditional systems is lost in expansion valves. The essential new features of the process are: (1) The application of two-step throttling of the working fluid and two-step compression of its vapor phase. (2) Use of a compressor as the initial step compression and a jet device as a second step, where throttling and compression are combined. (3) Controlled ratio of a working fluid at the first and

Tension and Compression Creep Apparatus for wood-Plastic Composites

Science.gov (United States)

Scott E. Hamel; John C. Hermanson; Steven M. Cramer

2011-01-01

Design of structural members made of wood-plastic composites (WPC) is not possible without accurate test data for tension and compression. The viscoelastic behavior of these materials means that these data are required for both the quasi-static stress-strain response, and the long-term creep response. Their relative incompressibility causes inherent difficulties in...

Trajectory grouping structure

Directory of Open Access Journals (Sweden)

Maike Buchin

2015-03-01

Full Text Available The collective motion of a set of moving entities like people, birds, or other animals, is characterized by groups arising, merging, splitting, and ending. Given the trajectories of these entities, we define and model a structure that captures all of such changes using the Reeb graph, a concept from topology. The trajectory grouping structure has three natural parameters that allow more global views of the data in group size, group duration, and entity inter-distance. We prove complexity bounds on the maximum number of maximal groups that can be present, and give algorithms to compute the grouping structure efficiently. We also study how the trajectory grouping structure can be made robust, that is, how brief interruptions of groups can be disregarded in the global structure, adding a notion of persistence to the structure. Furthermore, we showcase the results of experiments using data generated by the NetLogo flocking model and from the Starkey project. The Starkey data describe the movement of elk, deer, and cattle. Although there is no ground truth for the grouping structure in this data, the experiments show that the trajectory grouping structure is plausible and has the desired effects when changing the essential parameters. Our research provides the first complete study of trajectory group evolvement, including combinatorial,algorithmic, and experimental results.

SeqCompress: an algorithm for biological sequence compression.

Science.gov (United States)

Sardaraz, Muhammad; Tahir, Muhammad; Ikram, Ataul Aziz; Bajwa, Hassan

2014-10-01

The growth of Next Generation Sequencing technologies presents significant research challenges, specifically to design bioinformatics tools that handle massive amount of data efficiently. Biological sequence data storage cost has become a noticeable proportion of total cost in the generation and analysis. Particularly increase in DNA sequencing rate is significantly outstripping the rate of increase in disk storage capacity, which may go beyond the limit of storage capacity. It is essential to develop algorithms that handle large data sets via better memory management. This article presents a DNA sequence compression algorithm SeqCompress that copes with the space complexity of biological sequences. The algorithm is based on lossless data compression and uses statistical model as well as arithmetic coding to compress DNA sequences. The proposed algorithm is compared with recent specialized compression tools for biological sequences. Experimental results show that proposed algorithm has better compression gain as compared to other existing algorithms. Copyright © 2014 Elsevier Inc. All rights reserved.

A plastic damage model with stress triaxiality-dependent hardening

International Nuclear Information System (INIS)

Shen Xinpu; Shen Guoxiao; Zhou Lin

2005-01-01

Emphases of this study were placed on the modelling of plastic damage behaviour of prestressed structural concrete, with special attention being paid to the stress-triaxiality dependent plastic hardening law and the corresponding damage evolution law. A definition of stress triaxiality was proposed and introduced in the model presented here. Drucker-Prager -type plasticity was adopted in the formulation of the plastic damage constitutive equations. Numerical validations were performed for the proposed plasticity-based damage model with a driver subroutine developed in this study. The predicted stress-strain behaviour seems reasonably accurate for the uniaxial tension and uniaxial compression compared with the experimental data reported in references. Numerical calculations of compressions under various hydrostatic stress confinements were carried out in order to validate the stress triaxiality dependent properties of the model. (authors)

Design Issues of the Pre-Compression Rings of Iter

Science.gov (United States)

Knaster, J.; Baker, W.; Bettinali, L.; Jong, C.; Mallick, K.; Nardi, C.; Rajainmaki, H.; Rossi, P.; Semeraro, L.

2010-04-01

The pre-compression system is the keystone of ITER. A centripetal force of ˜30 MN will be applied at cryogenic conditions on top and bottom of each TF coil. It will prevent the `breathing effect' caused by the bursting forces occurring during plasma operation that would affect the machine design life of 30000 cycles. Different alternatives have been studied throughout the years. There are two major design requirements limiting the engineering possibilities: 1) the limited available space and 2) the need to hamper eddy currents flowing in the structures. Six unidirectionally wound glass-fibre composite rings (˜5 m diameter and ˜300 mm cross section) are the final design choice. The rings will withstand the maximum hoop stresses machine operation. The present paper summarizes the pre-compression ring R&D carried out during several years. In particular, we will address the composite choice and mechanical characterization, assessment of creep or stress relaxation phenomena, sub-sized rings testing and the optimal ring fabrication processes that have led to the present final design.

Effects of LSP on micro-structures and residual stresses in a 4 mm CLAM steel weld joints

Energy Technology Data Exchange (ETDEWEB)

Chen, Xizhang, E-mail: chenxizhang@wzu.edu.cn [School of Mechanical and Electrical Engineering, Wenzhou University., Wenzhou 325035 (China); School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China); Fang, Yuanyuan [School of Materials Science and Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China); Zhang, Shuyan; Kelleher, Joe F. [ISIS, Rutherford Appleton Laboratory, Chilton, Didcot OX11 0QX (United Kingdom); Zhou, Jianzhong [School of Mechanical Engineering, Jiangsu University, Zhenjiang 212013, Jiangsu (China)

2015-05-15

The effects of laser shock processing (LSP) on the distribution of residual stress and micro-structure of China Low Activation Martensitic (CLAM) steel weldment were investigated via neutron diffraction and optical microscope (OM). A pair of 4 mm CLAM steel plates joined by GTA welding. Special attention is paid to the generation of high level compressive residual stresses introduced by LSP. Residual stress in longitudinal, normal and transversal direction at weldment surface and longitudinal stress through thickness are evaluated via neutron diffraction. Compressive residual stress after LSP occurred at more than 90% areas within the weld joint, it is almost double the areas of compressive stress compare to weldment surface before LSP. The maximum compressive normal residual stress becomes to −183 MPa after LSP from −63 MPa before LSP. The Modification of surface micro-structures including weld zone (WZ), heat affected zone (HAZ) and base metal (BM) are also discussed. Results to date demonstrate that laser shock processing has been a great potential method for the improvement of mechanical performance of components.

On elastic waves in an thinly-layered laminated medium with stress couples under initial stress

Directory of Open Access Journals (Sweden)

P. Pal Roy

1988-01-01

Full Text Available The present work is concerned with a simple transformation rule in finding out the composite elastic coefficients of a thinly layered laminated medium whose bulk properties are strongly anisotropic with a microelastic bending rigidity. These elastic coefficients which were not known completely for a layered laminated structure, are obtained suitably in terms of initial stress components and Lame's constants λi, μi of initially isotropic solids. The explicit solutions of the dynamical equations for a prestressed thinly layered laminated medium under horizontal compression in a gravity field are derived. The results are discussed specifying the effects of hydrostatic, deviatoric and couple stresses upon the characteristic propagation velocities of shear and compression wave modes.

Micromagnetic modeling of the effects of stress on magnetic properties

International Nuclear Information System (INIS)

Zhu, B.; Lo, C. C. H.; Lee, S. J.; Jiles, D. C.

2001-01-01

A micromagnetic model has been developed for investigating the effect of stress on the magnetic properties of thin films. This effect has been implemented by including the magnetoelastic energy term into the Landau - Lifshitz - Gilbert equation. Magnetization curves of a nickel film were calculated under both tensile and compressive stresses of various magnitudes applied along the field direction. The modeling results show that coercivity increased with increasing compressive stress while remanence decreased with increasing tensile stress. The results are in agreement with the experimental data in the literature and can be interpreted in terms of the effects of the applied stress on the irreversible rotation of magnetic moments during magnetization reversal under an applied field. [copyright] 2001 American Institute of Physics

Prenatal stress perception and coping strategies: Insights from a longitudinal prospective pregnancy cohort.

Science.gov (United States)

Goletzke, J; Kocalevent, R-D; Hansen, G; Rose, M; Becher, H; Hecher, K; Arck, P C; Diemert, A

2017-11-01

Prenatal distress has been linked to pregnancy complications and poor offspring's health, despite the fact that longitudinal assessments of various stress dimensions are still lacking. Hence, we aimed to assess perceived stress over the course of pregnancy. Moreover, we examined whether social support and coping styles are linked to prenatal stress trajectories. Data from 543 women participating in the PRINCE (Prenatal Identification of Children Health) study, a prospective population-based cohort study, was used for the present analyses. Once per trimester the women completed questionnaires regarding different psychometric measures, including the Perceived Stress Scale (PSS). Linear mixed regression models were used to examine perceived stress development longitudinally and to relate social support and coping styles to stress trajectories during pregnancy. A significant decrease of perceived stress was observed over the course of pregnancy. Stratifying the study sample according to parity, women delivering their first child had continuously lower perceived stress scores compared to women having already one or more children, and a significant decrease during pregnancy was exclusively observed in primiparous women. Both, positive coping strategies and higher perceived and received social support were independently associated with lower perceived stress, while evasive coping strategies were associated with higher levels of perceived stress. Our study reveals stress perception trajectories during pregnancies in primi- and multiparous women. Our findings underscore the need for intervention strategies aiming to improve social support and positive coping strategies especially in multiparous women in order to reduce the risks for adverse pregnancy outcomes. Copyright © 2017 Elsevier Inc. All rights reserved.

Influence of Fe underlayers on stress evolution of Ti in Ti/Fe multilayers

Energy Technology Data Exchange (ETDEWEB)

Wan, Li; Thompson, Gregory, E-mail: gthompson@eng.ua.edu [Department of Metallurgical Engineering, The University of Alabama, Tuscaloosa, Alabama 35487-0202 (United States)

2016-11-15

A series of 40–2 nm bilayer spacing Ti/Fe multilayers were sputter-deposited. As the length scale of individual Ti layers equaled to 2 nm, Ti phase transforms from a hexagonal close packed (hcp)-to-body centered cubic (bcc) crystal structures for equal layer thicknesses in Ti/Fe multilayers. Further equal reductions in bilayer spacing to less than 1 nm resulted in an additional transformation from a crystalline to amorphous structure. Atom probe tomography reveals significant intermixing between layers which contributes to the observed phase transformations. Real-time, intrinsic growth stress measurements were also performed to relate the adatom mobility to these phase transformations. For the hcp Ti/bcc Fe multilayers of equivalent volume fractions, the multilayers undergo an overall tensile stress state to a compressive stress state with decreasing bilayer thickness for the multilayers. When the above phase transformations occurred, a modest reduction in the overall compressive stress of the multilayer was noted. Depending on the Fe thickness, the Ti growth was observed to be a tensile to compressive growth change to a purely compressive growth for thinner bilayer spacing. Fe retained a tensile growth stress regardless of the bilayer spacing studied.

Methods for determining the carrying capacity of eccentrically compressed concrete elements

Directory of Open Access Journals (Sweden)

Starishko Ivan Nikolaevich

2014-04-01

Full Text Available The author presents the results of calculations of eccentrically compressed elements in the ultimate limit state of bearing capacity, taking into account all possiblestresses in the longitudinal reinforcement from the R to the R , caused by different values of eccentricity longitudinal force. The method of calculation is based on the simultaneous solution of the equilibrium equations of the longitudinal forces and internal forces with the equilibrium equations of bending moments in the ultimate limit state of the normal sections. Simultaneous solution of these equations, as well as additional equations, reflecting the stress-strain limit state elements, leads to the solution of a cubic equation with respect to height of uncracked concrete, or with respect to the carrying capacity. According to the author it is a significant advantage over the existing methods, in which the equilibrium equations using longitudinal forces obtained one value of the height, and the equilibrium equations of bending moments - another. Theoretical studies of the author, in this article and the reasons to calculate specific examples showed that a decrease in the eccentricity of the longitudinal force in the limiting state of eccentrically compressed concrete elements height uncracked concrete height increases, the tension in the longitudinal reinforcement area gradually (not abruptly goes from a state of tension compression, and load-bearing capacity of elements it increases, which is also confirmed by the experimental results. Designed journalist calculations of eccentrically compressed elements for 4 cases of eccentric compression, instead of 2 - as set out in the regulations, fully cover the entire spectrum of possible cases of the stress-strain limit state elements that comply with the European standards for reinforced concrete, in particular Eurocode 2 (2003.

Measurements of three dimensional residual stress distribution on laser irradiated spot

International Nuclear Information System (INIS)

Tanaka, Hirotomo; Akita, Koichi; Ohya, Shin-ichi; Sano, Yuji; Naito, Hideki

2004-01-01

Three dimensional residual stress distributions on laser irradiated spots were measured using synchrotron radiation to study the basic mechanism of laser peening. A water-immersed sample of high tensile strength steel was irradiated with Q-switched and frequency-doubled Nd:YAG laser. The residual stress depth profile of the sample was obtained by alternately repeating the measurement and surface layer removal by electrolytic polishing. Tensile residual stresses were observed on the surface of all irradiated spots, whereas residual stress changed to compressive just beneath the surface. The depth of compressive residual stress imparted by laser irradiation and plastic deformation zone increased with increasing the number of laser pulses irradiated on the same spot. (author)

Stress in Childhood and Adulthood: Effects on Marital Quality over Time

Science.gov (United States)

Umberson, Debra; Williams, Kristi; Powers, Daniel A.; Liu, Hui; Needham, Belinda

2005-01-01

We work from a stress and life course perspective to consider how stress affects trajectories of change in marital quality over time. Specifically, we ask whether stress is more likely to undermine the quality of marital experiences at different points in the life course. In addition, we ask whether the effects of adult stress on marital quality…

Trajectory similarity join in spatial networks

KAUST Repository

Shang, Shuo

2017-09-07

The matching of similar pairs of objects, called similarity join, is fundamental functionality in data management. We consider the case of trajectory similarity join (TS-Join), where the objects are trajectories of vehicles moving in road networks. Thus, given two sets of trajectories and a threshold θ, the TS-Join returns all pairs of trajectories from the two sets with similarity above θ. This join targets applications such as trajectory near-duplicate detection, data cleaning, ridesharing recommendation, and traffic congestion prediction. With these applications in mind, we provide a purposeful definition of similarity. To enable efficient TS-Join processing on large sets of trajectories, we develop search space pruning techniques and take into account the parallel processing capabilities of modern processors. Specifically, we present a two-phase divide-and-conquer algorithm. For each trajectory, the algorithm first finds similar trajectories. Then it merges the results to achieve a final result. The algorithm exploits an upper bound on the spatiotemporal similarity and a heuristic scheduling strategy for search space pruning. The algorithm\\'s per-trajectory searches are independent of each other and can be performed in parallel, and the merging has constant cost. An empirical study with real data offers insight in the performance of the algorithm and demonstrates that is capable of outperforming a well-designed baseline algorithm by an order of magnitude.

Personalized trajectory matching in spatial networks

KAUST Repository

Shang, Shuo

2013-07-31

With the increasing availability of moving-object tracking data, trajectory search and matching is increasingly important. We propose and investigate a novel problem called personalized trajectory matching (PTM). In contrast to conventional trajectory similarity search by spatial distance only, PTM takes into account the significance of each sample point in a query trajectory. A PTM query takes a trajectory with user-specified weights for each sample point in the trajectory as its argument. It returns the trajectory in an argument data set with the highest similarity to the query trajectory. We believe that this type of query may bring significant benefits to users in many popular applications such as route planning, carpooling, friend recommendation, traffic analysis, urban computing, and location-based services in general. PTM query processing faces two challenges: how to prune the search space during the query processing and how to schedule multiple so-called expansion centers effectively. To address these challenges, a novel two-phase search algorithm is proposed that carefully selects a set of expansion centers from the query trajectory and exploits upper and lower bounds to prune the search space in the spatial and temporal domains. An efficiency study reveals that the algorithm explores the minimum search space in both domains. Second, a heuristic search strategy based on priority ranking is developed to schedule the multiple expansion centers, which can further prune the search space and enhance the query efficiency. The performance of the PTM query is studied in extensive experiments based on real and synthetic trajectory data sets. © 2013 Springer-Verlag Berlin Heidelberg.

Countermeasures to stress corrosion cracking by stress improvement

International Nuclear Information System (INIS)

Umemoto, Tadahiro

1983-01-01

One of the main factors of the grain boundary stress corrosion cracking occurred in the austenitic stainless steel pipes for reactor cooling system was the tensile residual stress due to welding, and a number of methods have been proposed to reduce the residual stress or to change it to compressive stress. In this paper, on the method of improving residual stress by high frequency heating, which has been applied most frequently, the principle, important parameters and the range of application are explained. Also the other methods of stress improvement are outlined, and the merit and demerit of respective methods are discussed. Austenitic stainless steel and high nickel alloys have good corrosion resistance, high toughness and good weldability, accordingly they have been used for reactor cooling system, but stress corrosion cracking was discovered in both BWRs and PWRs. It occurs when the sensitization of materials, tensile stress and the dissolved oxygen in high temperature water exceed certain levels simultaneously. The importance of the residual stress due to welding, induction heating stress improvement, and other methods such as heat sink welding, last pass heat sink welding, back lay welding and TIG torch heating stress improvement are described. (Kako, I.)

Numerical analysis oriented biaxial stress-strain relation and failure criterion of plain concrete

International Nuclear Information System (INIS)

Link, J.

1975-01-01

A biaxial stress-strain relation and failure criterion is proposed, which is applicable to structural analysis methods. The formulation of material behavior of plain concrete in biaxial stress-state was developed. A nonlinear elastic, anisotropic stress-strain relation was derived with two moduli of elasticity, E 1 , E 2 and Poisson's ratios, ν 1 , ν 2 , which depend on the prevailing biaxial stress state. The stress-strain relation is valid in the whole biaxial stress field, that means with a smooth transition between the domains of tension/tension, tension/compression and compression/compression. The stress-dependent moduli E 1 , E 2 and the Poisson's ratios ν 1 , ν 2 are approximated by polynomials, trigonometrical and exponential functions. A failure criterion was defined by approximating the test results of the biaxial ultimate concrete strength with a 7th degree polynomial, which is also valid in the whole biaxial stress domain. The definition of the state of failure is given as a function of stresses as well as strains. Initial parameters of the formulation of the biaxial material behavior are the uniaxial cylindrical strength of concrete and the initial values of Young's modulus and Poisson's ratio. A simple expansion of this formulation makes it applicable not only to normal but also to light-weight concrete. Comparison of numerically calculated stress-strain curves up to the ultimate biaxial stresses which indicate the failure criteria with those obtained from tests show a very good agreement. It is shown, that the biaxial stress-strain relation can be extended for use in cases of triaxial tension/tension/compression stress state. Numerical examples of analysis of concrete slabs show the importance of incorporation of a realistic material behavior for better safety estimations

Trajectory planning and trajectory tracking for a small-scale helicopter in autorotation

NARCIS (Netherlands)

Taamallah, Skander; Bombois, Xavier; Van den Hof, Paul M.J.

2017-01-01

The design of a high-performance guidance and control system for a small-scale helicopterUnmanned Aerial Vehicle (UAV), with an engine OFF flight condition (i.e. autorotation), is known to be a challenging task. It is the purpose of this paper to present a Trajectory Planning (TP) and Trajectory

Radiological Image Compression

Science.gov (United States)

Lo, Shih-Chung Benedict

The movement toward digital images in radiology presents the problem of how to conveniently and economically store, retrieve, and transmit the volume of digital images. Basic research into image data compression is necessary in order to move from a film-based department to an efficient digital -based department. Digital data compression technology consists of two types of compression technique: error-free and irreversible. Error -free image compression is desired; however, present techniques can only achieve compression ratio of from 1.5:1 to 3:1, depending upon the image characteristics. Irreversible image compression can achieve a much higher compression ratio; however, the image reconstructed from the compressed data shows some difference from the original image. This dissertation studies both error-free and irreversible image compression techniques. In particular, some modified error-free techniques have been tested and the recommended strategies for various radiological images are discussed. A full-frame bit-allocation irreversible compression technique has been derived. A total of 76 images which include CT head and body, and radiographs digitized to 2048 x 2048, 1024 x 1024, and 512 x 512 have been used to test this algorithm. The normalized mean -square-error (NMSE) on the difference image, defined as the difference between the original and the reconstructed image from a given compression ratio, is used as a global measurement on the quality of the reconstructed image. The NMSE's of total of 380 reconstructed and 380 difference images are measured and the results tabulated. Three complex compression methods are also suggested to compress images with special characteristics. Finally, various parameters which would effect the quality of the reconstructed images are discussed. A proposed hardware compression module is given in the last chapter.

Model for field-induced reorientation strain in magnetic shape memory alloy with tensile and compressive loads

International Nuclear Information System (INIS)

Zhu Yuping; Dui Guansuo

2008-01-01

A model based on the micromechanical and the thermodynamic theory is presented for field-induced martensite reorientation in magnetic shape memory alloy (MSMA) single crystals. The influence of variants morphology and the material property to constitutive behavior is considered. The nonlinear and hysteretic strain and magnetization response of MSMA are investigated for two main loading cases, namely the magnetic field-induced reorientation of variants under constant compressive stress and tensile stress. The predicted results have shown that increasing tensile loading reduces the required field for actuation, while increasing compressive loads result in the required magnetic field growing considerably. It is helpful to design the intelligent composite with MSMA fibers

Impact compressive and bending behaviour of rocks accompanied by electromagnetic phenomena.

Science.gov (United States)

Kobayashi, Hidetoshi; Horikawa, Keitaro; Ogawa, Kinya; Watanabe, Keiko

2014-08-28

It is well known that electromagnetic phenomena are often observed preceding earthquakes. However, the mechanism by which these electromagnetic waves are generated during the fracture and deformation of rocks has not been fully identified. Therefore, in order to examine the relationship between the electromagnetic phenomena and the mechanical properties of rocks, uniaxial compression and three-point bending tests for two kinds of rocks with different quartz content, granite and gabbro, have been carried out at quasi-static and dynamic rates. Especially, in the bending tests, pre-cracked specimens of granite were also tested. Using a split Hopkinson pressure bar and a ferrite-core antenna in close proximity to the specimens, both the stress-strain (load-displacement) curve and simultaneous electromagnetic wave magnitude were measured. It was found that the dynamic compressive and bending strengths and the stress increase slope of both rocks were higher than those observed in static tests; therefore, there is a strain-rate dependence in their strength and stress increase rate. It was found from the tests using the pre-cracked bending specimens that the intensity of electromagnetic waves measured during crack extension increased almost proportionally to the increase of the maximum stress intensity factor of specimens. This tendency was observed in both the dynamic and quasi-static three-point bending tests for granite. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

Compression etiology in tendinopathy.

Science.gov (United States)

Almekinders, Louis C; Weinhold, Paul S; Maffulli, Nicola

2003-10-01

Recent studies have emphasized that the etiology of tendinopathy is not as simple as was once thought. The etiology is likely to be multifactorial. Etiologic factors may include some of the traditional factors such as overuse, inflexibility, and equipment problems; however, other factors need to be considered as well, such as age-related tendon degeneration and biomechanical considerations as outlined in this article. More research is needed to determine the significance of stress-shielding and compression in tendinopathy. If they are confirmed to play a role, this finding may significantly alter our approach in both prevention and in treatment through exercise therapy. The current biomechanical studies indicate that certain joint positions are more likely to place tensile stress on the area of the tendon commonly affected by tendinopathy. These joint positions seem to be different than the traditional positions for stretching exercises used for prevention and rehabilitation of tendinopathic conditions. Incorporation of different joint positions during stretching exercises may exert more uniform, controlled tensile stress on these affected areas of the tendon and avoid stresshielding. These exercises may be able to better maintain the mechanical strength of that region of the tendon and thereby avoid injury. Alternatively, they could more uniformly stress a healing area of the tendon in a controlled manner, and thereby stimulate healing once an injury has occurred. Additional work will have to prove if a change in rehabilitation exercises is more efficacious that current techniques.

Formation of Sheeting Joints as a Result of Compression Parallel to Convex Surfaces, With Examples from Yosemite National Park, California

Science.gov (United States)

Martel, S. J.

2008-12-01

The formation of sheeting joints has been an outstanding problem in geology. New observations and analyses indicate that sheeting joints develop in response to a near-surface tension induced by compressive stresses parallel to a convex slope (hypothesis 1) rather than by removal of overburden by erosion, as conventionally assumed (hypothesis 2). Opening mode displacements across the joints together with the absence of mineral precipitates within the joints mean that sheeting joints open in response to a near-surface tension normal to the surface rather than a pressurized fluid. Consideration of a plot of this tensile stress as a function of depth normal to the surface reveals that a true tension must arise in the shallow subsurface if the rate of that tensile stress change with depth is positive at the surface. Static equilibrium requires this rate (derivative) to equal P22 k2 + P33 k3 - ρ g cosβ, where k2 and k3 are the principal curvatures of the surface, P22 and P33 are the respective surface- parallel normal stresses along the principal curvatures, ρ is the material density, g is gravitational acceleration, and β is the slope. This derivative will be positive and sheeting joints can open if at least one principal curvature is sufficiently convex (negative) and the surface-parallel stresses are sufficiently compressive (negative). At several sites with sheeting joints (e.g., Yosemite National Park in California), the measured topographic curvatures and the measured surface-parallel stresses of about -10 MPa combine to meet this condition. In apparent violation of hypothesis 1, sheeting joints occur locally at the bottom of Tenaya Canyon, one of the deepest glaciated, U-shaped (concave) canyons in the park. The canyon-bottom sheeting joints only occur, however, where the canyon is convex downstream, a direction that nearly coincides with direction of the most compressive stress measured in the vicinity. The most compressive stress acting along the convex

Experimental investigation of dynamic compression and spallation of Cerium at pressures up to 6 GPa

Science.gov (United States)

Zubareva, A. N.; Kolesnikov, S. A.; Utkin, A. V.

2014-05-01

In this study the experiments on one-dimensional dynamic compression of Cerium (Ce) samples to pressures of 0.5 to 6 GPa using various types of explosively driven generators were conducted. VISAR laser velocimeter was used to obtain Ce free surface velocity profiles. The isentropic compression wave was registered for γ-phase of Ce at pressures lower than 0.76 GPa that corresponds to γ-α phase transition pressure in Ce. Shock rarefaction waves were also registered in several experiments. Both observations were the result of the anomalous compressibility of γ-phase of Ce. On the basis of our experimental results the compression isentrope of Ce γ-phase was constructed. Its comparison with volumetric compression curves allowed to estimate the magnitude of shear stress at dynamic compression conditions for Ce. Spall strength measurements were also conducted for several samples. They showed a strong dependence of the spall strength of Ce on the strain rate.

Experimental investigation of dynamic compression and spallation of cerium at pressures up to 6 GPa

International Nuclear Information System (INIS)

Zubareva, A N; Kolesnikov, S A; Utkin, A V

2014-01-01

In this study the experiments on one-dimensional dynamic compression of Cerium (Ce) samples to pressures of 0.5 to 6 GPa using various types of explosively driven generators were conducted. VISAR laser velocimeter was used to obtain Ce free surface velocity profiles. The isentropic compression wave was registered for γ-phase of Ce at pressures lower than 0.76 GPa that corresponds to γ-α phase transition pressure in Ce. Shock rarefaction waves were also registered in several experiments. Both observations were the result of the anomalous compressibility of γ-phase of Ce. On the basis of our experimental results the compression isentrope of Ce γ-phase was constructed. Its comparison with volumetric compression curves allowed to estimate the magnitude of shear stress at dynamic compression conditions for Ce. Spall strength measurements were also conducted for several samples. They showed a strong dependence of the spall strength of Ce on the strain rate.

Trajectories of schizotypy and their emotional and social functioning: An 18-month follow-up study.

Science.gov (United States)

Wang, Yi; Shi, Hai-Song; Liu, Wen-Hua; Xie, Dong-Jie; Geng, Fu-Lei; Yan, Chao; Wang, Ya; Xiao, Ya-Hui; So, Suzanne H W; Chiu, Chui-De; Leung, Patrick W L; Cheung, Eric F C; Gooding, Diane C; Chan, Raymond C K

2018-03-01

Schizotypy is a set of personality traits that convey liability to develop schizophrenia. Studying schizotypy in healthy individuals may facilitate the understanding of the psychopathological processes underlying schizophrenia. The present study aimed to examine the developmental trajectories of schizotypy over time using a longitudinal study design. The Chapman Scales for Psychosis Proneness were administered to 1541 college students at baseline, and subsequently at six-monthly intervals up to 18months. Latent class growth analysis was conducted to track the different trajectories. In addition, self-reported scales were used to measure idea of reference, emotional experiences and expression, stress and coping, as well as social functioning. We identified four latent classes with distinct trajectories: "nonschizotypy" group (LC1), "stable high schizotypy" group (LC3), "high reactive schizotypy" group (LC2) and "low reactive schizotypy" group (LC4). These findings suggest that there may be distinct developmental trajectories for schizotypy. Two groups may be of particular interest: the "stable high schizotypy" group that displayed the worst clinical and functioning outcomes on almost all measures and the "high reactive schizotypy" group characterized by a relatively rapid decline in functioning. Copyright © 2017 Elsevier B.V. All rights reserved.

INTERFACE RESIDUAL STRESSES IN DENTAL ZIRCONIA USING LAUE MICRO-DIFFRACTION

International Nuclear Information System (INIS)

Bale, H. A.; Tamura, N.; Coelho, P.G.; Hanan, J. C.

2009-01-01

Due to their aesthetic value and high compressive strength, dentists have recently employed ceramics for restoration materials. Among the ceramic materials, zirconia provides high toughness and crack resistant characteristics. Residual stresses develop in processing due to factors including grain anisotropy and thermal coefficient mismatch. In the present study, polychromatic X-ray (Laue) micro-diffraction provided grain orientation and residual stresses on a clinically relevant zirconia model ceramic disk. A 0.5 mm x 0.024 mm region on zirconia was examined on a 500 nm scale for residual stresses using a focused poly-chromatic synchrotron X-ray beam. Large stresses ranging from - to + 1GPa were observed at some grains. On average, the method suggests a relatively small compressive stress at the surface between 47 and 75 MPa depending on direction

The use of Stress Tensor Discriminator Faults in separating heterogeneous fault-slip data with best-fit stress inversion methods. II. Compressional stress regimes

Science.gov (United States)

Tranos, Markos D.

2018-02-01

Synthetic heterogeneous fault-slip data as driven by Andersonian compressional stress tensors were used to examine the efficiency of best-fit stress inversion methods in separating them. Heterogeneous fault-slip data are separated only if (a) they have been driven by stress tensors defining 'hybrid' compression (R constitute a necessary discriminatory tool for the establishment and comparison of two compressional stress tensors determined by a best-fit stress inversion method. The best-fit stress inversion methods are not able to determine more than one 'real' compressional stress tensor, as far as the thrust stacking in an orogeny is concerned. They can only possibly discern stress differences in the late-orogenic faulting processes, but not between the main- and late-orogenic stages.

Influence of alkali-silica reaction and crack orientation on the uniaxial compressive strength of concrete cores from slab bridges

DEFF Research Database (Denmark)

Antonio Barbosa, Ricardo; Gustenhoff Hansen, Søren; Hansen, Kurt Kielsgaard

2018-01-01

ASR-damaged flat slab bridges in service. Furthermore, the influence of the ASR-induced crack orientation on the compressive strength and the Young’s modulus is investigated. Uniaxial compression tests, visual observations, and thin section examinations were performed on more than 100 cores drilled...... from the three severely ASR-damaged flat slab bridges. It was found that the orientation of ASR-induced cracks has a significant influence on the uniaxial compressive strength and the stress-strain relationship of the tested cores. The compressive strength in a direction parallel to ASR cracks can...

Residual stress behaviors induced by laser peening along the edge of curved models

International Nuclear Information System (INIS)

Im, Jong Bin; Grandhi, Ramana V.; Ro, Young Hee

2012-01-01

Laser peening (LP) induces high magnitude compressive residual stresses in a small region of a component. The compressive residual stresses cause plastic deformation that is resistant to fatigue fracture. Fatigue cracks are generally nucleated at critical areas, and LP is applied for those regions so as to delay the crack initiation. Many critical regions are located on the edge of the curved portion of structures because of stress concentration effects. Several investigations that are available for straight components may not give meaningful guidelines for peening curved components. Therefore, in this paper, we investigate residual stress behaviors induced by LP along the edge of curved models. Three curved models that have different curvatures are investigated for peening performance. Two types of peening configurations, which are simultaneous corner shot and sequential corner shots, are considered in order to obtain compressive residual stresses along an edge. LP simulations of multiple shots are performed to identify overlapping effects on the edge portion of a curved model. In addition, the uncertainty calculation of residual stress induced by LP considering laser pulse duration is performed

Lunar Cube Transfer Trajectory Options

Science.gov (United States)

Folta, David; Dichmann, Donald James; Clark, Pamela E.; Haapala, Amanda; Howell, Kathleen

2015-01-01

Numerous Earth-Moon trajectory and lunar orbit options are available for Cubesat missions. Given the limited Cubesat injection infrastructure, transfer trajectories are contingent upon the modification of an initial condition of the injected or deployed orbit. Additionally, these transfers can be restricted by the selection or designs of Cubesat subsystems such as propulsion or communication. Nonetheless, many trajectory options can b e considered which have a wide range of transfer duration, fuel requirements, and final destinations. Our investigation of potential trajectories highlights several options including deployment from low Earth orbit (LEO) geostationary transfer orbits (GTO) and higher energy direct lunar transfer and the use of longer duration Earth-Moon dynamical systems. For missions with an intended lunar orbit, much of the design process is spent optimizing a ballistic capture while other science locations such as Sun-Earth libration or heliocentric orbits may simply require a reduced Delta-V imparted at a convenient location along the trajectory.

Biomechanical Property of a Newly Designed Assembly Locking Compression Plate: Three-Dimensional Finite Element Analysis

Directory of Open Access Journals (Sweden)

Jiang-Jun Zhou

2017-01-01

Full Text Available In this study, we developed and validated a refined three-dimensional finite element model of middle femoral comminuted fracture to compare the biomechanical stability after two kinds of plate fixation: a newly designed assembly locking compression plate (NALCP and a locking compression plate (LCP. CT data of a male volunteer was converted to middle femoral comminuted fracture finite element analysis model. The fracture was fixated by NALCP and LCP. Stress distributions were observed. Under slow walking load and torsion load, the stress distribution tendency of the two plates was roughly uniform. The anterolateral femur was the tension stress area, and the bone block shifted toward the anterolateral femur. Maximum stress was found on the lateral border of the number 5 countersink of the plate. Under a slow walking load, the NALCP maximum stress was 2.160e+03 MPa and the LCP was 8.561e+02 MPa. Under torsion load, the NALCP maximum stress was 2.260e+03 MPa and the LCP was 6.813e+02 MPa. Based on those results of finite element analysis, the NALCP can provide adequate mechanical stability for comminuted fractures, which would help fixate the bone block and promote bone healing.

Towards Efficient Search for Activity Trajectories

DEFF Research Database (Denmark)

Zheng, Kai; Shang, Shuo; Yuan, Jing

2013-01-01

, recent proliferation in location-based web applications (e.g., Foursquare, Facebook) has given rise to large amounts of trajectories associated with activity information, called activity trajectory. In this paper, we study the problem of efficient similarity search on activity trajectory database. Given...

Residual stress improving method for reactor structural component and residual stress improving device therefor

Energy Technology Data Exchange (ETDEWEB)

Enomoto, Kunio; Otaka, Masahiro; Kurosawa, Koichi; Saito, Hideyo; Tsujimura, Hiroshi; Tamai, Yasukata; Urashiro, Keiichi; Mochizuki, Masato

1996-09-03

The present invention is applied to a BWR type reactor, in which a high speed jetting flow incorporating cavities is collided against the surface of reactor structural components to form residual compression stresses on the surface layer of the reactor structural components thereby improving the stresses on the surface. Namely, a water jetting means is inserted into the reactor container filled with reactor water. Purified water is pressurized by a pump and introduced to the water jetting means. The purified water jetted from the water jetting means and entraining cavities is abutted against the surface of the reactor structural components. With such procedures, since the purified water is introduced to the water jetting means by the pump, the pump is free from contamination of radioactive materials. As a result, maintenance and inspection for the pump can be facilitated. Further, since the purified water injection flow entraining cavities is abutted against the surface of the reactor structural components being in contact with reactor water, residual compression stresses are exerted on the surface of the reactor structural components. As a result, occurrence of stress corrosion crackings of reactor structural components is suppressed. (I.S.)

Residual stress improving method for reactor structural component and residual stress improving device therefor

International Nuclear Information System (INIS)

Enomoto, Kunio; Otaka, Masahiro; Kurosawa, Koichi; Saito, Hideyo; Tsujimura, Hiroshi; Tamai, Yasukata; Urashiro, Keiichi; Mochizuki, Masato.

1996-01-01

The present invention is applied to a BWR type reactor, in which a high speed jetting flow incorporating cavities is collided against the surface of reactor structural components to form residual compression stresses on the surface layer of the reactor structural components thereby improving the stresses on the surface. Namely, a water jetting means is inserted into the reactor container filled with reactor water. Purified water is pressurized by a pump and introduced to the water jetting means. The purified water jetted from the water jetting means and entraining cavities is abutted against the surface of the reactor structural components. With such procedures, since the purified water is introduced to the water jetting means by the pump, the pump is free from contamination of radioactive materials. As a result, maintenance and inspection for the pump can be facilitated. Further, since the purified water injection flow entraining cavities is abutted against the surface of the reactor structural components being in contact with reactor water, residual compression stresses are exerted on the surface of the reactor structural components. As a result, occurrence of stress corrosion crackings of reactor structural components is suppressed. (I.S.)

Efficient Trajectory Options Allocation for the Collaborative Trajectory Options Program

Science.gov (United States)

Rodionova, Olga; Arneson, Heather; Sridhar, Banavar; Evans, Antony

2017-01-01

The Collaborative Trajectory Options Program (CTOP) is a Traffic Management Initiative (TMI) intended to control the air traffic flow rates at multiple specified Flow Constrained Areas (FCAs), where demand exceeds capacity. CTOP allows flight operators to submit the desired Trajectory Options Set (TOS) for each affected flight with associated Relative Trajectory Cost (RTC) for each option. CTOP then creates a feasible schedule that complies with capacity constraints by assigning affected flights with routes and departure delays in such a way as to minimize the total cost while maintaining equity across flight operators. The current version of CTOP implements a Ration-by-Schedule (RBS) scheme, which assigns the best available options to flights based on a First-Scheduled-First-Served heuristic. In the present study, an alternative flight scheduling approach is developed based on linear optimization. Results suggest that such an approach can significantly reduce flight delays, in the deterministic case, while maintaining equity as defined using a Max-Min fairness scheme.

Flight test trajectory control analysis

Science.gov (United States)

Walker, R.; Gupta, N.

1983-01-01

Recent extensions to optimal control theory applied to meaningful linear models with sufficiently flexible software tools provide powerful techniques for designing flight test trajectory controllers (FTTCs). This report describes the principal steps for systematic development of flight trajectory controllers, which can be summarized as planning, modeling, designing, and validating a trajectory controller. The techniques have been kept as general as possible and should apply to a wide range of problems where quantities must be computed and displayed to a pilot to improve pilot effectiveness and to reduce workload and fatigue. To illustrate the approach, a detailed trajectory guidance law is developed and demonstrated for the F-15 aircraft flying the zoom-and-pushover maneuver.

Compressive Residual Strains in Mineral Nanoparticles as a Possible Origin of Enhanced Crack Resistance in Human Tooth Dentin.

Science.gov (United States)

Forien, Jean-Baptiste; Fleck, Claudia; Cloetens, Peter; Duda, Georg; Fratzl, Peter; Zolotoyabko, Emil; Zaslansky, Paul

2015-06-10

The tough bulk of dentin in teeth supports enamel, creating cutting and grinding biostructures with superior failure resistance that is not fully understood. Synchrotron-based diffraction methods, utilizing micro- and nanofocused X-ray beams, reveal that the nm-sized mineral particles aligned with collagen are precompressed and that the residual strains vanish upon mild annealing. We show the link between the mineral nanoparticles and known damage propagation trajectories in dentin, suggesting a previously overlooked compression-mediated toughening mechanism.