WorldWideScience

Sample records for comprehensive design operating

  1. FIELD TEST PROGRAM TO DEVELOP COMPREHENSIVE DESIGN, OPERATING, AND COST DATA FOR MERCURY CONTROL SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    Michael D. Durham

    2004-10-01

    PG&E NEG Salem Harbor Station Unit 1 was successfully tested for applicability of activated carbon injection as a mercury control technology. Test results from this site have enabled a thorough evaluation of mercury control at Salem Harbor Unit 1, including performance, estimated cost, and operation data. This unit has very high native mercury removal, thus it was important to understand the impacts of process variables on native mercury capture. The team responsible for executing this program included plant and PG&E headquarters personnel, EPRI and several of its member companies, DOE, ADA, Norit Americas, Inc., Hamon Research-Cottrell, Apogee Scientific, TRC Environmental Corporation, Reaction Engineering, as well as other laboratories. The technical support of all of these entities came together to make this program achieve its goals. Overall the objectives of this field test program were to determine the mercury control and balance-of-plant impacts resulting from activated carbon injection into a full-scale ESP on Salem Harbor Unit 1, a low sulfur bituminous-coal-fired 86 MW unit. It was also important to understand the impacts of process variables on native mercury removal (>85%). One half of the gas stream was used for these tests, or 43 MWe. Activated carbon, DARCO FGD supplied by NORIT Americas, was injected upstream of the cold side ESP, just downstream of the air preheater. This allowed for approximately 1.5 seconds residence time in the duct before entering the ESP. Conditions tested in this field evaluation included the impacts of the Selective Non-Catalytic Reduction (SNCR) system on mercury capture, of unburned carbon in the fly ash, of adjusting ESP inlet flue gas temperatures, and of boiler load on mercury control. The field evaluation conducted at Salem Harbor looked at several sorbent injection concentrations at several flue gas temperatures. It was noted that at the mid temperature range of 322-327 F, the LOI (unburned carbon) lost some of its

  2. FIELD TEST PROGRAM TO DEVELOP COMPREHENSIVE DESIGN, OPERATING, AND COST DATA FOR MERCURY CONTROL SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    Michael D. Durham

    2003-05-01

    With the Nation's coal-burning utilities facing the possibility of tighter controls on mercury pollutants, the U.S. Department of Energy is funding projects that could offer power plant operators better ways to reduce these emissions at much lower costs. Mercury is known to have toxic effects on the nervous system of humans and wildlife. Although it exists only in trace amounts in coal, mercury is released when coal burns and can accumulate on land and in water. In water, bacteria transform the metal into methylmercury, the most hazardous form of the metal. Methylmercury can collect in fish and marine mammals in concentrations hundreds of thousands times higher than the levels in surrounding waters. One of the goals of DOE is to develop technologies by 2005 that will be capable of cutting mercury emissions 50 to 70 percent at well under one-half of today's costs. ADA Environmental Solutions (ADA-ES) is managing a project to test mercury control technologies at full scale at four different power plants from 2000--2003. The ADA-ES project is focused on those power plants that are not equipped with wet flue gas desulfurization systems. ADA-ES has developed a portable system that will be tested at four different utility power plants. Each of the plants is equipped with either electrostatic precipitators or fabric filters to remove solid particles from the plant's flue gas. ADA-ES's technology will inject a dry sorbent, such as activated carbon, which removes the mercury and makes it more susceptible to capture by the particulate control devices. A fine water mist may be sprayed into the flue gas to cool its temperature to the range where the dry sorbent is most effective. PG&E National Energy Group is providing two test sites that fire bituminous coals and both are equipped with electrostatic precipitators and carbon/ash separation systems. Wisconsin Electric Power Company is providing a third test site that burns Powder River Basin (PRB) coal and

  3. FIELD TEST PROGRAM TO DEVELOP COMPREHENSIVE DESIGN, OPERATING, AND COST DATA FOR MERCURY CONTROL SYSTEMS

    Energy Technology Data Exchange (ETDEWEB)

    Michael D. Durham

    2005-03-17

    Brayton Point Unit 1 was successfully tested for applicability of activated carbon injection as a mercury control technology. Test results from this site have enabled a thorough evaluation of the impacts of future mercury regulations to Brayton Point Unit 1, including performance, estimated cost, and operation data. This unit has variable (29-75%) native mercury removal, thus it was important to understand the impacts of process variables and activated carbon on mercury capture. The team responsible for executing this program included: (1) Plant and PG&E National Energy Group corporate personnel; (2) Electric Power Research Institute (EPRI); (3) United States Department of Energy National Energy Technology Laboratory (DOE/NETL); (4) ADA-ES, Inc.; (5) NORIT Americas, Inc.; (6) Apogee Scientific, Inc.; (7) TRC Environmental Corporation; (8) URS Corporation; (9) Quinapoxet Solutions; (10) Energy and Environmental Strategies (EES); and (11) Reaction Engineering International (REI). The technical support of all of these entities came together to make this program achieve its goals. Overall, the objectives of this field test program were to determine the impact of activated carbon injection on mercury control and balance-of-plant processes on Brayton Point Unit 1. Brayton Point Unit 1 is a 250-MW unit that fires a low-sulfur eastern bituminous coal. Particulate control is achieved by two electrostatic precipitators (ESPs) in series. The full-scale tests were conducted on one-half of the flue gas stream (nominally 125 MW). Mercury control sorbents were injected in between the two ESPs. The residence time from the injection grid to the second ESP was approximately 0.5 seconds. In preparation for the full-scale tests, 12 different sorbents were evaluated in a slipstream of flue gas via a packed-bed field test apparatus for mercury adsorption. Results from these tests were used to determine the five carbon-based sorbents that were tested at full-scale. Conditions of interest

  4. The high performance HMI handbook a comprehensive guide to designing, implementing and maintaining effective HMIs for industrial plant operations

    CERN Document Server

    Hollifield, Bill; Nimmo, Ian; Habibi, Eddie

    2008-01-01

    The High Performance HMI Handbook is the first and only comprehensive book containing the best-practice principles for assessing, designing, and implementing proper process control Human-Machine Interfaces (HMIs). Poorly designed and poorly performing Human Machine Interfaces (HMIs) are rampant throughout the process industries. They can degrade safety, production, quality, and profitability. Time after time, they are cited as contributing factors to major industrial accidents. The book contains experience and intellectual property that has never before been released, It is jointly authored by 2 companies, PAS and User Centered Design Services (UCDS), who have decades of experience in process control, HMI design, and human factors. The book reveals many poor yet common HMI practices, provides the justification for change, and shows in great detail the best way to design and implement a truly High Performance HMI. It contains over 90 color illustrations, plus many relevant real world examples, anecdotes, and ...

  5. Listening Comprehension: Approach, Design, Procedure.

    Science.gov (United States)

    Richards, Jack C.

    1983-01-01

    Three dimensions in the teaching of listening comprehension are outlined: (1) a theory is presented that takes account of the cognitive processes used (approach); (2) listeners' needs are analyzed and a taxonomy of microskills and objectives for teaching them are proposed (design); and (3) classroom exercises and activities are suggested…

  6. Comprehensive Performance Nutrition for Special Operations Forces.

    Science.gov (United States)

    Daigle, Karen A; Logan, Christi M; Kotwal, Russ S

    2015-01-01

    Special Operations Forces (SOF) training, combat, and contingency operations are unique and demanding. Performance nutrition within the Department of Defense has emphasized that nutrition is relative to factors related to the desired outcome, which includes successful performance of mentally and physically demanding operations and missions of tactical and strategic importance, as well as nonoperational assignments. Discussed are operational, nonoperational, and patient categories that require different nutrition strategies to facilitate category-specific performance outcomes. Also presented are 10 major guidelines for a SOF comprehensive performance nutrition program, practical nutrition recommendations for Special Operators and medical providers, as well as resources for dietary supplement evaluation. Foundational health concepts, medical treatment, and task-specific performance factors should be considered when developing and systematically implementing a comprehensive SOF performance nutrition program. When tailored to organizational requirements, SOF unit- and culture-specific nutrition education and services can optimize individual Special Operator performance, overall unit readiness, and ultimately, mission success. 2015.

  7. The Comprehensive Approach Concept in Multinational Operations

    Directory of Open Access Journals (Sweden)

    Neag Mihai-Marcel

    2017-12-01

    Full Text Available The planning of operations is regulated by documents covering the participation of forces in military actions in a national and multinational context. The process of planning the operations has been adapted to conceptual planning progress. The concept of allied effect-based operations, which was an alternative to old national concepts, has undergone transformations, so the process of planning operations at allied level is currently based on the concept of a comprehensive approach, which is a strategic concept, do not give up effects. The term action-based operations has been replaced by the term “thought-based thinking” and belongs to the general concept of comprehensive approach. If the planning process meant the effects, so the main planning objectives were the effects, then the planning was based on concrete objectives, the effects being maintained for the economy of effort and maximizing efficiency, the main purpose of the effects being the evaluation of the operations. From this point of view, we consider that the concept has not been abandoned, what has changed, it was just the working method, the subject being still topical.

  8. [Designing and Operating a Comprehensive Mental Health Management System to Support Faculty at a University That Contains a Medical School and University Hospital].

    Science.gov (United States)

    Kawanishi, Chiaki

    2016-01-01

    In Japan, healthcare professionals and healthcare workers typically practice a culture of self-assessment when it comes to managing their own health. Even where this background leads to instances of mental health disorders or other serious problems within a given organization, such cases are customarily addressed by the psychiatrists or psychiatric departments of the facilities affected. Organized occupational mental health initiatives for professionals and workers within the healthcare system are extremely rare across Japan, and there is little recognition of the need for such initiatives even among those most directly affected. The author has some experience designing and operating a comprehensive health management system to support students and faculty at a university in the Tokyo Metropolitan Area that contains a medical school and university hospital. At this university, various mental health-related problems were routinely being allowed to develop into serious cases, while the fundamental reforms required by the health management center and the mental health management scheme organized through the center had come to represent a challenge for the entire university. From this initial situation, we undertook several successive initiatives, including raising the number of staff in the health management center and its affiliated organizations, revising and drafting new health management rules and regulations, launching an employment support and management system, implementing screenings to identify people with mental ill-health, revamping and expanding a counselling response system, instituting regular collaboration meetings with academic affairs staff, and launching educational and awareness-raising activities. This resulted in the possibility of intervention in all cases of mental health crisis, such as suicidal ideation. We counted more than 2,400 consultations (cumulative total number; more than half of consultations was from the medical school, postgraduate

  9. A comprehensive approach to assess operational resilience

    NARCIS (Netherlands)

    Stolker, R.J.M.; Karydas, D.M.; Rouvroye, J.L.; Hollnagel, E.; Pieri, F.

    2008-01-01

    This paper presents a first attempt to apply Multi-Attribute Utility Theory (MAUT) to the concept of resilience. The focus of this paper is measuring the management performance of operational resilience in an organization. Operational resilience refers to the ability of an organization to prevent

  10. Comprehensive Solutions for Integration of Solar Resources into Grid Operations

    Energy Technology Data Exchange (ETDEWEB)

    Pennock, Kenneth [AWS Truepower, LLC, Albany, NY (United States); Makarov, Yuri V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rajagopal, Sankaran [Siemens Energy, Erlangen (Germany); Loutan, Clyde [California Independent System Operator; Etingov, Pavel V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Miller, Laurie E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lu, Bo [Siemens Energy, Erlangen (Germany); Mansingh, Ashmin [Siemens Energy, Erlangen (Germany); Zack, John [MESO, Inc., Raleigh, NC (United States); Sherick, Robert [Southern California Edison, Rosemead, CA (United States); Romo, Abraham [Southern California Edison; Habibi-Ashrafi, Farrokh [Southern California Edison; Johnson, Raymond [Southern California Edison

    2016-01-14

    The need for proactive closed-loop integration of uncertainty information into system operations and probability-based controls is widely recognized, but rarely implemented in system operations. Proactive integration for this project means that the information concerning expected uncertainty ranges for net load and balancing requirements, including required balancing capacity, ramping and ramp duration characteristics, will be fed back into the generation commitment and dispatch algorithms to modify their performance so that potential shortages of these characteristics can be prevented. This basic, yet important, premise is the motivating factor for this project. The achieved project goal is to demonstrate the benefit of such a system. The project quantifies future uncertainties, predicts additional system balancing needs including the prediction intervals for capacity and ramping requirements of future dispatch intervals, evaluates the impacts of uncertainties on transmission including the risk of overloads and voltage problems, and explores opportunities for intra-hour generation adjustments helping to provide more flexibility for system operators. The resulting benefits culminate in more reliable grid operation in the face of increased system uncertainty and variability caused by solar power. The project identifies that solar power does not require special separate penetration level restrictions or penalization for its intermittency. Ultimately, the collective consideration of all sources of intermittency distributed over a wide area unified with the comprehensive evaluation of various elements of balancing process, i.e. capacity, ramping, and energy requirements, help system operators more robustly and effectively balance generation against load and interchange. This project showed that doing so can facilitate more solar and other renewable resources on the grid without compromising reliability and control performance. Efforts during the project included

  11. FIELD TEST PROGRAM TO DEVELOP COMPREHENSIVE DESIGN, OPERATING AND COST DATA FOR MERCURY CONTROL SYSTEMS ON NON-SCRUBBED COAL-FIRED BOILERS

    International Nuclear Information System (INIS)

    C. Jean Bustard

    2001-01-01

    With the Nation's coal-burning utilities facing the possibility of tighter controls on mercury pollutants, the U.S. Department of Energy is funding projects that could offer power plant operators better ways to reduce these emissions at much lower costs. Mercury is known to have toxic effects on the nervous system of humans and wildlife. Although it exists only in trace amounts in coal, mercury is released when coal burns and can accumulate on land and in water. In water, bacteria transform the metal into methylmercury, the most hazardous form of the metal. Methylmercury can collect in fish and marine mammals in concentrations hundreds of thousands times higher than the levels in surrounding waters. One of the goals of DOE is to develop technologies by 2005 that will be capable of cutting mercury emissions 50 to 70 percent at well under one-half of today's costs. ADA Environmental Solutions (ADA-ES) is managing a project to test mercury control technologies at full scale at four different power plants from 2000 to 2003. The ADA-ES project is focused on those power plants that are not equipped with wet flue gas desulfurization systems. ADA-ES will develop a portable system that will be moved to four different utility power plants for field testing. Each of the plants is equipped with either electrostatic precipitators or fabric filters to remove solid particles from the plant's flue gas. ADA-ES's technology will inject a dry sorbent, such as fly ash or activated carbon, that removes the mercury and makes it more susceptible to capture by the particulate control devices. A fine water mist may be sprayed into the flue gas to cool its temperature to the range where the dry sorbent is most effective. PG and E National Energy Group is providing two test sites that fire bituminous coals and are both equipped with electrostatic precipitators and carbon/ash separation systems. Wisconsin Electric Power Company is providing a third test site that burns Powder River Basin (PRB

  12. FIELD TEST PROGRAM TO DEVELOP COMPREHENSIVE DESIGN, OPERATING AND COST DATA FOR MERCURY CONTROL SYSTEMS ON NON-SCRUBBED COAL-FIRED BOILERS

    International Nuclear Information System (INIS)

    C. Jean Bustard

    2002-01-01

    With the Nation's coal-burning utilities facing the possibility of tighter controls on mercury pollutants, the U.S. Department of Energy is funding projects that could offer power plant operators better ways to reduce these emissions at much lower costs. Mercury is known to have toxic effects on the nervous system of humans and wildlife. Although it exists only in trace amounts in coal, mercury is released when coal burns and can accumulate on land and in water. In water, bacteria transform the metal into methylmercury, the most hazardous form of the metal. Methylmercury can collect in fish and marine mammals in concentrations hundreds of thousands times higher than the levels in surrounding waters. One of the goals of DOE is to develop technologies by 2005 that will be capable of cutting mercury emissions 50 to 70 percent at well under one-half of today's costs. ADA Environmental Solutions (ADA-ES) is managing a project to test mercury control technologies at full scale at four different power plants from 2000-2003. The ADA-ES project is focused on those power plants that are not equipped with wet flue gas desulfurization systems. ADA-ES will develop a portable system that will be moved to four different utility power plants for field testing. Each of the plants is equipped with either electrostatic precipitators or fabric filters to remove solid particles from the plant's flue gas. ADA-ES's technology will inject a dry sorbent, such as fly ash or activated carbon, that removes the mercury and makes it more susceptible to capture by the particulate control devices. A fine water mist may be sprayed into the flue gas to cool its temperature to the range where the dry sorbent is most effective. PG and E National Energy Group is providing two test sites that fire bituminous coals and are both equipped with electrostatic precipitators and carbon/ash separation systems. Wisconsin Electric Power Company is providing a third test site that burns Powder River Basin (PRB

  13. FIELD TEST PROGRAM TO DEVELOP COMPREHENSIVE DESIGN, OPERATING AND COST DATA FOR MERCURY CONTROL SYSTEMS ON NON-SCRUBBED COAL-FIRED BOILERS

    International Nuclear Information System (INIS)

    C. Jean Bustard

    2001-01-01

    With the Nation's coal-burning utilities facing the possibility of tighter controls on mercury pollutants, the U.S. Department of Energy is funding projects that could offer power plant operators better ways to reduce these emissions at much lower costs. Mercury is known to have toxic effects on the nervous system of humans and wildlife. Although it exists only in trace amounts in coal, mercury is released when coal burns and can accumulate on land and in water. In water, bacteria transform the metal into methylmercury, the most hazardous form of the metal. Methylmercury can collect in fish and marine mammals in concentrations hundreds of thousands times higher than the levels in surrounding waters. One of the goals of DOE is to develop technologies by 2005 that will be capable of cutting mercury emissions 50 to 70 percent at well under one-half of today's costs. ADA Environmental Solutions (ADA-ES) is managing a project to test mercury control technologies at full scale at four different power plants from 2000-2003. The ADA-ES project is focused on those power plants that are not equipped with wet flue gas desulfurization systems. ADA-ES will develop a portable system that will be moved to four different utility power plants for field testing. Each of the plants is equipped with either electrostatic precipitators or fabric filters to remove solid particles from the plant's flue gas. ADA-ES's technology will inject a dry sorbent, such as fly ash or activated carbon, that removes the mercury and makes it more susceptible to capture by the particulate control devices. A fine water mist may be sprayed into the flue gas to cool its temperature to the range where the dry sorbent is most effective. PG and E National Energy Group is providing two test sites that fire bituminous coals and are both equipped with electrostatic precipitators and carbon/ash separation systems. Wisconsin Electric Power Company is providing a third test site that burns Powder River Basin coal

  14. FIELD TEST PROGRAM TO DEVELOP COMPREHENSIVE DESIGN, OPERATING AND COST DATA FOR MERCURY CONTROL SYSTEMS ON NON-SCRUBBED COAL-FIRED BOILERS

    International Nuclear Information System (INIS)

    C. Jean Bustard

    2001-01-01

    With the Nation's coal-burning utilities facing the possibility of tighter controls on mercury pollutants, the U.S. Department of Energy is funding projects that could offer power plant operators better ways to reduce these emissions at much lower costs. Mercury is known to have toxic effects on the nervous system of humans and wildlife. Although it exists only in trace amounts in coal, mercury is released when coal burns and can accumulate on land and in water. In water, bacteria transform the metal into methylmercury, the most hazardous form of the metal. Methylmercury can collect in fish and marine mammals in concentrations hundreds of thousands times higher than the levels in surrounding waters. One of the goals of DOE is to develop technologies by 2005 that will be capable of cutting mercury emissions 50 to 70 percent at well under one-half of today's costs. ADA Environmental Solutions (ADA-ES) is managing a project to test mercury control technologies at full scale at four different power plants from 2000-2003. The ADA-ES project is focused on those power plants that are not equipped with wet flue gas desulfurization systems. ADA-ES will develop a portable system that will be moved to four different utility power plants for field testing. Each of the plants is equipped with either electrostatic precipitators or fabric filters to remove solid particles from the plant's flue gas. ADA-ES's technology will inject a dry sorbent, such as fly ash or activated carbon, that removes the mercury and makes it more susceptible to capture by the particulate control devices. A fine water mist may be sprayed into the flue gas to cool its temperature to the range where the dry sorbent is most effective. PG and E National Energy Group is providing two test sites that fire bituminous coals and are both equipped with electrostatic precipitators and carbon/ash separation systems. Wisconsin Electric Power Company is providing a third test site that burns Powder River Basin (PRB

  15. Discourse in Systemic Operational Design

    National Research Council Canada - National Science Library

    DiPasquale, Joseph A

    2007-01-01

    .... The monograph presents alternative ways to consider discourse, the implications of this for theory of Systemic Operational Design, and how these alternatives can lead to a richer understanding...

  16. Design for maintenance during operation

    International Nuclear Information System (INIS)

    Barton, P.H.; Lyerly, H.D.

    1976-01-01

    Design of a nuclear power plant for safe, reliable and efficient operation involves much more than theory, regulations, regulatory guides, procedures, inspectors, and even quality assurance. It also involves a full knowledge and understanding of the activities which must be carried out to operate and maintain the plant. It must be remembered that a nuclear power plant is different from fossil designs and the designer must constantly keep in mind that access by people to every component is required for maintenance

  17. Comprehensive evaluation method in application of nuclear DCS product design

    International Nuclear Information System (INIS)

    Wang Weixin; Zhao Zhemin; Shi Yingbin

    2014-01-01

    In order to select the best design proposal in short time, the TOPSIS comprehensive evaluation method in the nuclear power plant DCS product design was introduced. It can intuitively show the different design proposals good or not good by data and shorten the time of the design proposal optimization. The design proposal selected by this method will be more reasonable and has good comprehensive performance indexes. The TOPSIS comprehensive evaluation method achieves good result in one of the nuclear power plant DCS cabinet design proposal optimization. (authors)

  18. Operational amplifiers theory and design

    CERN Document Server

    Huijsing, Johan

    2017-01-01

    This proven textbook guides readers to a thorough understanding of the theory and design of operational amplifiers (OpAmps). The core of the book presents systematically the design of operational amplifiers, classifying them into a periodic system of nine main overall configurations, ranging from one gain stage up to four or more stages. This division enables circuit designers to recognize quickly, understand, and choose optimal configurations. Characterization of operational amplifiers is given by macro models and error matrices, together with measurement techniques for their parameters. Definitions are given for four types of operational amplifiers depending on the grounding of their input and output ports. Many famous designs are evaluated in depth, using a carefully structured approach enhanced by numerous figures. In order to reinforce the concepts introduced and facilitate self-evaluation of design skills, the author includes problems with detailed solutions, as well as simulation exercises. Provides te...

  19. [Comprehensive system integration and networking in operating rooms].

    Science.gov (United States)

    Feußner, H; Ostler, D; Kohn, N; Vogel, T; Wilhelm, D; Koller, S; Kranzfelder, M

    2016-12-01

    comprehensive surveillance and control system integrating all devices and functions is a precondition for realization of the operating room of the future. Multiple proprietary integrated operation room systems are currently available with a central user interface; however, they only cover a relatively small part of all functionalities. Internationally, there are at least three different initiatives to promote a comprehensive systems integration and networking in the operating room: the Japanese smart cyber operating theater (SCOT), the American medical device plug-and-play interoperability program (MDPnP) and the German secure and dynamic networking in operating room and hospital (OR.NET) project supported by the Federal Ministry of Education and Research. Within the framework of the internationally advanced OR.NET project, prototype solution approaches were realized, which make short-term and mid-term comprehensive data retrieval systems probable. An active and even autonomous control of the medical devices by the surveillance and control system (closed loop) is expected only in the long run due to strict regulatory barriers.

  20. Small-State Special Operations in a Comprehensive Stabilisation Context

    DEFF Research Database (Denmark)

    Johnsen, Anton Asklund

    takeaways were: Special operations as a force multiplier: Can special operations enable other stabilisation agents, locals as well as internationals, to accomplish their missions more effectively? This includes NGOs, diplomats or other officials, other military units, etc. How can the mindset required...... to enable ‘whole-of-government’ approaches be promoted? Economy of force considerations: Are special operations truly a cheaper means of reaching certain ends? When are small and indirect approaches involving special operations forces effective and when are they not? Special operations as expansion......“Small-State Special Operations in a Comprehensive Stabilisation Context: What to Know and Where to Go?” was the headline of a conference held at the Royal Danish Defence College, facilitated by the Institute for Strategy. As a product of this conference, a report has been written which highlights...

  1. Ergonomic design for operator flexibility

    International Nuclear Information System (INIS)

    Pope, R.H.

    1980-01-01

    The Three Mile Island accident highlighted the importance of ergonomic design of control rooms. Emphasis has been on a reappraisal of the reactor/operator interface, but in the United Kingdom the CEGB maintains that safe efficient operation needs a centralised information system optimised for all control room staff. (author)

  2. Designing Facilities for Collaborative Operations

    Science.gov (United States)

    Norris, Jeffrey; Powell, Mark; Backes, Paul; Steinke, Robert; Tso, Kam; Wales, Roxana

    2003-01-01

    A methodology for designing operational facilities for collaboration by multiple experts has begun to take shape as an outgrowth of a project to design such facilities for scientific operations of the planned 2003 Mars Exploration Rover (MER) mission. The methodology could also be applicable to the design of military "situation rooms" and other facilities for terrestrial missions. It was recognized in this project that modern mission operations depend heavily upon the collaborative use of computers. It was further recognized that tests have shown that layout of a facility exerts a dramatic effect on the efficiency and endurance of the operations staff. The facility designs (for example, see figure) and the methodology developed during the project reflect this recognition. One element of the methodology is a metric, called effective capacity, that was created for use in evaluating proposed MER operational facilities and may also be useful for evaluating other collaboration spaces, including meeting rooms and military situation rooms. The effective capacity of a facility is defined as the number of people in the facility who can be meaningfully engaged in its operations. A person is considered to be meaningfully engaged if the person can (1) see, hear, and communicate with everyone else present; (2) see the material under discussion (typically data on a piece of paper, computer monitor, or projection screen); and (3) provide input to the product under development by the group. The effective capacity of a facility is less than the number of people that can physically fit in the facility. For example, a typical office that contains a desktop computer has an effective capacity of .4, while a small conference room that contains a projection screen has an effective capacity of around 10. Little or no benefit would be derived from allowing the number of persons in an operational facility to exceed its effective capacity: At best, the operations staff would be underutilized

  3. Towards the Comprehensive Design of Energy Infrastructures

    NARCIS (Netherlands)

    Scholten, D.J.; Kunneke, R.W.

    2016-01-01

    Energy infrastructures are increasingly perceived as complex, adaptive socio-technical systems. Their design has not kept up; it is still fragmented between an engineering and economic dimension. While economists focus on a market design that addresses potential market failures and imperfections,

  4. Operations Monitoring Assistant System Design

    Science.gov (United States)

    1986-07-01

    Logic. Artificial Inteligence 25(1)::75-94. January.18. 41 -Nils J. Nilsson. Problem-Solving Methods In Artificli Intelligence. .klcG raw-Hill B3ook...operations monitoring assistant (OMA) system is designed that combines operations research, artificial intelligence, and human reasoning techniques and...KnowledgeCraft (from Carnegie Group), and 5.1 (from Teknowledze). These tools incorporate the best methods of applied artificial intelligence, and

  5. Comprehensive computational design of ordered peptide macrocycles

    Science.gov (United States)

    Hosseinzadeh, Parisa; Bhardwaj, Gaurav; Mulligan, Vikram Khipple; Shortridge, Matthew D.; Craven, Timothy W.; Pardo-Avila, Fátima; Rettie, Stephen A.; Kim, David E.; Silva, Daniel-Adriano; Ibrahim, Yehia M.; Webb, Ian K.; Cort, John R.; Adkins, Joshua N.; Varani, Gabriele; Baker, David

    2018-01-01

    Mixed-chirality peptide macrocycles such as cyclosporine are among the most potent therapeutics identified to date, but there is currently no way to systematically search the structural space spanned by such compounds. Natural proteins do not provide a useful guide: Peptide macrocycles lack regular secondary structures and hydrophobic cores, and can contain local structures not accessible with L-amino acids. Here, we enumerate the stable structures that can be adopted by macrocyclic peptides composed of L- and D-amino acids by near-exhaustive backbone sampling followed by sequence design and energy landscape calculations. We identify more than 200 designs predicted to fold into single stable structures, many times more than the number of currently available unbound peptide macrocycle structures. Nuclear magnetic resonance structures of 9 of 12 designed 7- to 10-residue macrocycles, and three 11- to 14-residue bicyclic designs, are close to the computational models. Our results provide a nearly complete coverage of the rich space of structures possible for short peptide macrocycles and vastly increase the available starting scaffolds for both rational drug design and library selection methods. PMID:29242347

  6. Design Principles for a Comprehensive Library System.

    Science.gov (United States)

    Uluakar, Tamer; And Others

    1981-01-01

    Describes an online design featuring circulation control, catalog access, and serial holdings that uses an incremental approach to system development. Utilizing a dedicated computer, this second of three releases pays particular attention to present and predicted computing capabilities as well as trends in library automation. (Author/RAA)

  7. Comprehensive computational design of ordered peptide macrocycles

    Energy Technology Data Exchange (ETDEWEB)

    Hosseinzadeh, Parisa; Bhardwaj, Gaurav; Mulligan, Vikram K.; Shortridge, Matthew D.; Craven, Timothy W.; Pardo-Avila, Fatima; Rettie, Stephan A.; Kim, David E.; Silva, Daniel A.; Ibrahim, Yehia M.; Webb, Ian K.; Cort, John R.; Adkins, Joshua N.; Varani, Gabriele; Baker, David

    2017-12-14

    Mixed chirality peptide macrocycles such as cyclosporine are among the most potent therapeutics identified to-date, but there is currently no way to systematically search through the structural space spanned by such compounds for new drug candidates. Natural proteins do not provide a useful guide: peptide macrocycles lack regular secondary structures and hydrophobic cores and have different backbone torsional constraints. Hence the development of new peptide macrocycles has been approached by modifying natural products or using library selection methods; the former is limited by the small number of known structures, and the latter by the limited size and diversity accessible through library-based methods. To overcome these limitations, here we enumerate the stable structures that can be adopted by macrocyclic peptides composed of L and D amino acids. We identify more than 200 designs predicted to fold into single stable structures, many times more than the number of currently available unbound peptide macrocycle structures. We synthesize and characterize by NMR twelve 7-10 residue macrocycles, 9 of which have structures very close to the design models in solution. NMR structures of three 11-14 residue bicyclic designs are also very close to the computational models. Our results provide a nearly complete coverage of the rich space of structures possible for short peptide based macrocycles unparalleled for other molecular systems, and vastly increase the available starting scaffolds for both rational drug design and library selection methods.

  8. Facility design, installation and operation

    International Nuclear Information System (INIS)

    Fleischmann, A.W.

    1985-01-01

    Problems that may arise when considering the design, construction and use of a facility that could contain up to tens of petabecquerel of either cobalt-60 or caesium-137 are examined. The safe operation of an irradiation facility depends on an appreciation of the in built safety systems, adequate training of personnel and the existence of an emergency system

  9. Study on supporting system for operator's comprehensive understanding

    International Nuclear Information System (INIS)

    Yoshikawa, Shinji

    1996-01-01

    Power Reactor and Nuclear Fuel Development Corp. has participated in the development of a system to support the process of operator's plant understanding by the use of information processing techniques such as artificial intelligence since 1994. Analysis and model formation of the process leading to operator's comprehensive understanding of plant (mental model) are undertaken attempting to determine the basic structure of the mental model available for the description of knowledge using the precedent survey and to observe how to utilize operator's own knowledge. After consideration of the way by which plant operators utilize their physical knowledges and the knowledges of physical observation in practice, a basic structure composed of 3 components a qualitative causal network, a hierarchical function model and 3 links joining the two was proposed for the mental model. A questionnaire survey on operator's statements was made and the contents were assigned in several categories for objective analysis. An unified form usable to make a data base was established. Further, we have a plan to develop the first proto-type system to promote operator's understanding by 1998. (M.N.)

  10. Operator theory a comprehensive course in analysis, part 4

    CERN Document Server

    Simon, Barry

    2015-01-01

    A Comprehensive Course in Analysis by Poincaré Prize winner Barry Simon is a five-volume set that can serve as a graduate-level analysis textbook with a lot of additional bonus information, including hundreds of problems and numerous notes that extend the text and provide important historical background. Depth and breadth of exposition make this set a valuable reference source for almost all areas of classical analysis. Part 4 focuses on operator theory, especially on a Hilbert space. Central topics are the spectral theorem, the theory of trace class and Fredholm determinants, and the study of

  11. Facility design, construction, and operation

    International Nuclear Information System (INIS)

    1995-04-01

    France has been disposing of low-level radioactive waste (LLW) at the Centre de Stockage de la Manche (CSM) since 1969 and now at the Centre de Stockage de l'Aube (CSA) since 1992. In France, several agencies and companies are involved in the development and implementation of LLW technology. The Commissariat a l'Energie Atomic (CEA), is responsible for research and development of new technologies. The Agence National pour la Gestion des Dechets Radioactifs is the agency responsible for the construction and operation of disposal facilities and for wastes acceptance for these facilities. Compagnie Generale des Matieres Nucleaires provides fuel services, including uranium enrichment, fuel fabrication, and fuel reprocessing, and is thus one generator of LLW. Societe pour les Techniques Nouvelles is an engineering company responsible for commercializing CEA waste management technology and for engineering and design support for the facilities. Numatec, Inc. is a US company representing these French companies and agencies in the US. In Task 1.1 of Numatec's contract with Martin Marietta Energy Systems, Numatec provides details on the design, construction and operation of the LLW disposal facilities at CSM and CSA. Lessons learned from operation of CSM and incorporated into the design, construction and operating procedures at CSA are identified and discussed. The process used by the French for identification, selection, and evaluation of disposal technologies is provided. Specifically, the decisionmaking process resulting in the change in disposal facility design for the CSA versus the CSM is discussed. This report provides' all of the basic information in these areas and reflects actual experience to date

  12. Operational Design for Peace Enforcement: Lessons for the Operational Staff

    National Research Council Canada - National Science Library

    Neumann, Michael

    2004-01-01

    U.S. involvement in Somalia serves as a useful case study of the unique challenges an operational staff may face when applying operational design to the planning and execution of a peace enforcement operation. U.S...

  13. Systemic Operational Design: Enhancing the Joint Operation Planning Process

    National Research Council Canada - National Science Library

    Delacruz, Victor J

    2007-01-01

    Operational level commanders and their staffs require relevant and current joint doctrine that articulates the critical function of operational design and its role in the Joint Operation Planning Process (JOPP...

  14. A comprehensive survey of brain interface technology designs.

    Science.gov (United States)

    Mason, S G; Bashashati, A; Fatourechi, M; Navarro, K F; Birch, G E

    2007-02-01

    In this work we present the first comprehensive survey of Brain Interface (BI) technology designs published prior to January 2006. Detailed results from this survey, which was based on the Brain Interface Design Framework proposed by Mason and Birch, are presented and discussed to address the following research questions: (1) which BI technologies are directly comparable, (2) what technology designs exist, (3) which application areas (users, activities and environments) have been targeted in these designs, (4) which design approaches have received little or no research and are possible opportunities for new technology, and (5) how well are designs reported. The results of this work demonstrate that meta-analysis of high-level BI design attributes is possible and informative. The survey also produced a valuable, historical cross-reference where BI technology designers can identify what types of technology have been proposed and by whom.

  15. Safety of research reactors (Design and Operation)

    International Nuclear Information System (INIS)

    Dirar, H. M.

    2012-06-01

    The primary objective of this thesis is to conduct a comprehensive up-to-date literature review on the current status of safety of research reactor both in design and operation providing the future trends in safety of research reactors. Data and technical information of variety selected historical research reactors were thoroughly reviewed and evaluated, furthermore illustrations of the material of fuel, control rods, shielding, moderators and coolants used were discussed. Insight study of some historical research reactors was carried with considering sample cases such as Chicago Pile-1, F-1 reactor, Chalk River Laboratories,. The National Research Experimental Reactor and others. The current status of research reactors and their geographical distribution, reactor category and utilization is also covered. Examples of some recent advanced reactors were studied like safety barriers of HANARO of Korea including safety doors of the hall and building entrance and finger print identification which prevent the reactor from sabotage. On the basis of the results of this research, it is apparent that a high quality of safety of nuclear reactors can be attained by achieving enough robust construction, designing components of high levels of efficiency, replacing the compounds of the reactor in order to avoid corrosion and degradation with age, coupled with experienced scientists and technical staffs to operate nuclear research facilities.(Author)

  16. Comprehensive analysis of a Radiology Operations Management computer system.

    Science.gov (United States)

    Arenson, R L; London, J W

    1979-11-01

    The Radiology Operations Management computer system at the Hospital of the University of Pennsylvania is discussed. The scheduling and file room modules are based on the system at Massachusetts General Hospital. Patient delays are indicated by the patient tracking module. A reporting module allows CRT/keyboard entry by transcriptionists, entry of standard reports by radiologists using bar code labels, and entry by radiologists using a specialty designed diagnostic reporting terminal. Time-flow analyses demonstrate a significant improvement in scheduling, patient waiting, retrieval of radiographs, and report delivery. Recovery of previously lost billing contributes to the proved cost effectiveness of this system.

  17. The design and application of comprehensive interventional surgery record:evaluation of its usefulness

    International Nuclear Information System (INIS)

    Li Xue; Chen Jinhua; Li Jun

    2010-01-01

    Objective: To design a comprehensive interventional surgery record form in order to standardize and simplify interventional work process and to increase the operative safety. Methods: A comprehensive interventional surgery record form was designed by the authors, which was suitable for making necessary record of different kinds of interventional procedures, for counting operation time, X-ray exposure time and for recording the dose, velocity and injection pressure of the contrast agent used in interventional procedure. The record form made a close combination of the nursing notes with the technological information and focused on compiling the clinical key points. The record form included independent parts for taking the preoperative, in-operative and postoperative facts and evaluations. The corresponding items after employing this record form were compared with that before using this form. The usefulness of the form was evaluated. Results: The use of comprehensive interventional surgery record form overcame the limitations of previously used interventional record chart. The previous record chart paid attention only to the vital signs and operative process, while the newly designed form emphasized the scientific management, which would make the therapeutic procedure to be more standard and the control of X-ray dose and contrast media dosage to be more strict, providing powerful data for scientific administration. After using the comprehensive interventional surgery record form both the nurses' and technicians' comprehensive abilities were improved markedly. Conclusion: The specific and comprehensive interventional record form designed by the authors fully meets the requirements of various interventional procedures, reflecting the particular needs for medical record. The use of this record form can standardize the administration of clinical interventional work. (authors)

  18. Modeling and Design of Container Terminal Operations

    NARCIS (Netherlands)

    D. Roy (Debjit); M.B.M. de Koster (René)

    2014-01-01

    textabstractDesign of container terminal operations is complex because multiple factors affect the operational perfor- mance. These factors include: topological constraints, a large number of design parameters and settings, and stochastic interactions that interplay among the quayside, vehicle

  19. Industrial and process furnaces principles, design and operation

    CERN Document Server

    Jenkins, Barrie

    2014-01-01

    Furnaces sit at the core of all branches of manufacture and industry, so it is vital that these are designed and operated safely and effi-ciently. This reference provides all of the furnace theory needed to ensure that this can be executed successfully on an industrial scale. Industrial and Process Furnaces: Principles, 2nd Edition provides comprehensive coverage of all aspects of furnace operation and design, including topics essential for process engineers and operators to better understand furnaces. This includes: the combustion process and its control, furnace fuels, efficiency,

  20. Operations Management and Curriculum Design.

    Science.gov (United States)

    Slack, Nigel

    1983-01-01

    The last few years have seen developments in the academic treatment of operations management which both broaden the subject to include a much wider range of industries in the nonmanufacturing sectors and place the operations function in a more strategic context. (MEAD Subscriptions, CSML, University of Lancaster, Lancaster LA1 4YX, England) (SSH)

  1. Forest Fire Management: A Comprehensive And Operational Approach

    Science.gov (United States)

    Fabrizi, Roberto; Perez, Bruno; Gomez, Antonio

    2013-12-01

    Remote sensing plays an important role in obtaining rapid and complete information on the occurrence and evolution in space and time of forest fires. In this paper, we present a comprehensive study of fire events through Earth Observation data for early warning, crisis monitoring and post-event damage assessment or a synthesis of the fire event, both in a wide spatial range (local to regional) and temporal scale (short to long term). The fire products are stored and distributed by means of a WebGIS and a Geoportal with additional auxiliary geospatial data. These products allow fire managers to perform analysis and decision making in a more comprehensive manner.

  2. Sustainable Rest Area Design and Operations

    Science.gov (United States)

    2017-10-01

    One way in which State Departments of Transportation (DOTs) can modernize their rest areas while reducing operations and maintenance costs is by incorporating sustainable practices into rest area design and operations. Sustainability practices that D...

  3. Designing and conducting survey research a comprehensive guide

    CERN Document Server

    Rea, Louis M

    2014-01-01

    The industry standard guide, updated with new ideas and SPSS analysis techniques Designing and Conducting Survey Research: A Comprehensive Guide Fourth Edition is the industry standard resource that covers all major components of the survey process, updated to include new data analysis techniques and SPSS procedures with sample data sets online. The book offers practical, actionable guidance on constructing the instrument, administrating the process, and analyzing and reporting the results, providing extensive examples and worksheets that demonstrate the appropriate use of survey and data tech

  4. Danish Special Operations - Comprehensive Reorganization and Innovation are Necessary

    DEFF Research Database (Denmark)

    Jensen, Lars H. Ehrensvärd

    This fourth paper in a series of research briefs about Danish special operations is focusing on how a "system's failure" has blocked the development of Danish special operations for almost 50 years. The brief suggests the repair of this system's failure by creating either a fourth service...... or a special operations command. The paper points out that a political decision is necessary, as there is no known empirical evidence that the conventional military has ever created any special operations institutions by it's own will. (The establishment of a Danish Special Operations Command was actually...

  5. Operational Intelligence and Operational Design: Thinking about Operational Art

    Science.gov (United States)

    2011-06-01

    captured it best when he wrote, ―Operational intelligence is more or less the fusion of 45 Kent... Market Garden….‖34 Additionally, Drea concluded that the strong-minded General Douglas MacArthur‘s ―sense of destiny‖ shaped his strategic concepts...1960. Memorandum RM-4172-ISA, Santa Monica, CA: The RAND Corporation, September 1964. The Bible . New International Version. Hitchcock, Walter T., ed

  6. A comprehensive operating room information system using the Kinect sensors and RFID.

    Science.gov (United States)

    Nouei, Mahyar Taghizadeh; Kamyad, Ali Vahidian; Soroush, Ahmad Reza; Ghazalbash, Somayeh

    2015-04-01

    Occasionally, surgeons do need various types of information to be available rapidly, efficiently and safely during surgical procedures. Meanwhile, they need to free up hands throughout the surgery to necessarily access the mouse to control any application in the sterility mode. In addition, they are required to record audio as well as video files, and enter and save some data. This is an attempt to develop a comprehensive operating room information system called "Medinav" to tackle all mentioned issues. An integrated and comprehensive operating room information system is introduced to be compatible with Health Level 7 (HL7) and digital imaging and communications in medicine (DICOM). DICOM is a standard for handling, storing, printing, and transmitting information in medical imaging. Besides, a natural user interface (NUI) is designed specifically for operating rooms where touch-less interactions with finger and hand tracking are in use. Further, the system could both record procedural data automatically, and view acquired information from multiple perspectives graphically. A prototype system is tested in a live operating room environment at an Iranian teaching hospital. There are also contextual interviews and usability satisfaction questionnaires conducted with the "MediNav" system to investigate how useful the proposed system could be. The results reveal that integration of these systems into a complete solution is the key to not only stream up data and workflow but maximize surgical team usefulness as well. It is now possible to comprehensively collect and visualize medical information, and access a management tool with a touch-less NUI in a rather quick, practical, and harmless manner.

  7. How Mode of Delivery Affects Comprehension of an Operations Management Simulation: Online vs Face-to-Face Classrooms

    Science.gov (United States)

    Riley, Jason M.; Ellegood, William A.; Solomon, Stanislaus; Baker, Jerrine

    2017-01-01

    Purpose: This study aims to understand how mode of delivery, online versus face-to-face, affects comprehension when teaching operations management concepts via a simulation. Conceptually, the aim is to identify factors that influence the students' ability to learn and retain new concepts. Design/methodology/approach: Leveraging Littlefield…

  8. Post-'92 Helsinki. Towards an operational institution for comprehensive security

    International Nuclear Information System (INIS)

    Ghebali, V.Y.

    1992-01-01

    Discussing the concept of comprehensive security the author reviews aims of the Forum for Security Cooperation to be held in Vienna in September 1992. They are: 1. To negotiate specific new conventional disarmament measures, provisions harmonizing the obligations assumed under various international instruments in this area; 2. To provide a framework for consultation, cooperation and ongoing dialogue on security questions; 3. To elaborate on the theme of conflict prevention

  9. Discourse in Systemic Operational Design

    Science.gov (United States)

    2007-05-22

    narrative theory and theories of agency in the education of officers about design use and practice. This comes from the idea that if 1 the discourse of... educational philosophy reference points, the same knowledge may be processed in significantly different ways. Similarly, these differences inform the...feminine reproductive health often places normal occurrences such as menstruation in a negative, pathological frame of reference relative to male health

  10. Comprehensive, Integrated Reconstruction Operations: We Need a Master Plan

    National Research Council Canada - National Science Library

    Dosa, Brian L

    2007-01-01

    The U.S. military has historically played a critical role during post-conflict stability operations, contributing to the overall goal of achieving long term security and securing our strategic interests...

  11. Thermal power plant design and operation

    CERN Document Server

    Sarkar, Dipak

    2015-01-01

    Thermal Power Plant: Design and Operation deals with various aspects of a thermal power plant, providing a new dimension to the subject, with focus on operating practices and troubleshooting, as well as technology and design. Its author has a 40-long association with thermal power plants in design as well as field engineering, sharing his experience with professional engineers under various training capacities, such as training programs for graduate engineers and operating personnel. Thermal Power Plant presents practical content on coal-, gas-, oil-, peat- and biomass-fueled thermal power

  12. Maintenance analysis method and operational feedback: a comprehensive maintenance management

    International Nuclear Information System (INIS)

    Mathieu Riou; Victor Planchon

    2006-01-01

    Full text of publication follows: Current periodic inspections program carried out on the COGEMA LOGISTICS casks is required by regulations and approved by the competent Authority. Thus, Safety and casks conformity to the according certificate of approval are guaranteed. Nonetheless, based on experience it appeared that some maintenance operations did not seem relevant or were redundant. Then, it was decided to rethink completely our maintenance program to reach the following objectives: - Set up the 'a minima' required inspection operations required to guarantee Safety and conformity to the certificate of approval, - Optimize criteria and periodicities of inspections taking into account: operational feedback, routine inspections carried out for each transport, regulations, environmental impact (ALARA, waste reduction,...), cost-effectiveness (reduction of cask's immobilization period,...). - Set up a maintenance program in Safety Analysis Reports that: stands alone (no need to check the specification or the certificate of approval to have the complete list of inspections mandatory to guarantee Safety), gives objectives instead of means of controls. This approach needs then to be re-evaluated by the competent Authority. Study's scope has been limited to the TN TM 12 cask family which is intensely used. COGEMA LOGISTICS has a high operational feedback on these casks. After Authority agreement, and in accordance with its requirements, study will then be extended to the other casks belonging to the COGEMA LOGISTICS cask fleet. Actually, the term 'maintenance' is linked to 'Base maintenance' and 'Main maintenance' and implicitly means that the cask is immobilized for a given period. To emphasize the modifications, the term 'maintenance' is no longer used and is substituted by 'periodic upkeep'. By changing the name, COGEMA LOGISTICS wants to emphasize that: some operations can for instance be realized while the cask is unloaded, periodicities are thought in terms of

  13. Indications of comprehensiveness in the pedagogical relationship: a design to be constructed in nursing education.

    Science.gov (United States)

    Lima, Margarete Maria de; Reibnitz, Kenya Schmidt; Kloh, Daiana; Martini, Jussara Gue; Backes, Vania Marli Schubert

    2017-11-27

    To analyze how the indications of comprehensiveness translate into the teaching-learning process in a nursing undergraduate course. Qualitative case study carried out with professors of a Nursing Undergraduate Course. Data collection occurred through documentary analysis, non-participant observation and individual interviews. Data analysis was guided from an analytical matrix following the steps of the operative proposal. Eight professors participated in the study. Some indications of comprehensiveness such as dialogue, listening, mutual respect, bonding and welcoming are present in the daily life of some professors. The indications of comprehensiveness are applied by some professors in the pedagogical relationship. The results refer to the Comprehensiveness of teaching-learning in a single and double loop model, and in this the professor and the student assume an open posture for new possibilities in the teaching-learning process. Comprehensiveness, as it is recognized as a pedagogical principle, allows the disruption of a professor-centered teaching and advances in collective learning, enabling the professor and student to create their own design anchored in a reflective process about their practices and the reality found in the health services.

  14. Applying operating experience to design the CANDU 3 process

    International Nuclear Information System (INIS)

    Harris, D.S.; Hinchley, E.M.; Pauksens, J.; Snell, V.; Yu, S.K.W.

    1991-01-01

    The CANDU 3 is an advanced, smaller (450 MWe), standardized version of the CANDU now being designed for service later in the decade and beyond. The design of this evolutionary nuclear power plant has been carefully planned and organized to gain maximum benefits from new technologies and from world experience to date in designing, building, commissioning and operating nuclear power stations. The good performance record of existing CANDU reactors makes consideration of operating experience from these plants a particularly vital component of the design process. Since the completion of the first four CANDU 6 stations in the early 1980s, and with the continuing evolution of the multi-unit CANDU station designs since then, AECL CANDU has devised several processes to ensure that such feedback is made available to designers. An important step was made in 1986 when a task force was set up to review and process ideas arising from the commissioning and early operation of the CANDU 6 reactors which were, by that time, operating successfully in Argentina and Korea, as well as the Canadian provinces of Quebec and New Brunswick. The task force issued a comprehensive report which, although aimed at the design of an improved CANDU 6 station, was made available to the CANDU 3 team. By that time also, the Institute of Power Operations (INPO) in the U.S., of which AECL is a Supplier Participant member, was starting to publish Good Practices and Guidelines related to the review and the use of operating experiences. In addition, details of significant events were being made available via the INPO SEE-IN (Significant Event Evaluation and Information Network) Program, and subsequently the CANNET network of the CANDU Owners' Group (COG). Systematic review was thus possible by designers of operations reports, significant event reports, and related documents in a continuing program of design improvement. Another method of incorporating operations feedback is to involve experienced utility

  15. Applying operating experience to design the CANDU 3 process

    Energy Technology Data Exchange (ETDEWEB)

    Harris, D S; Hinchley, E M; Pauksens, J; Snell, V; Yu, S K.W. [AECL-CANDU, Ontario (Canada)

    1991-04-01

    The CANDU 3 is an advanced, smaller (450 MWe), standardized version of the CANDU now being designed for service later in the decade and beyond. The design of this evolutionary nuclear power plant has been carefully planned and organized to gain maximum benefits from new technologies and from world experience to date in designing, building, commissioning and operating nuclear power stations. The good performance record of existing CANDU reactors makes consideration of operating experience from these plants a particularly vital component of the design process. Since the completion of the first four CANDU 6 stations in the early 1980s, and with the continuing evolution of the multi-unit CANDU station designs since then, AECL CANDU has devised several processes to ensure that such feedback is made available to designers. An important step was made in 1986 when a task force was set up to review and process ideas arising from the commissioning and early operation of the CANDU 6 reactors which were, by that time, operating successfully in Argentina and Korea, as well as the Canadian provinces of Quebec and New Brunswick. The task force issued a comprehensive report which, although aimed at the design of an improved CANDU 6 station, was made available to the CANDU 3 team. By that time also, the Institute of Power Operations (INPO) in the U.S., of which AECL is a Supplier Participant member, was starting to publish Good Practices and Guidelines related to the review and the use of operating experiences. In addition, details of significant events were being made available via the INPO SEE-IN (Significant Event Evaluation and Information Network) Program, and subsequently the CANNET network of the CANDU Owners' Group (COG). Systematic review was thus possible by designers of operations reports, significant event reports, and related documents in a continuing program of design improvement. Another method of incorporating operations feedback is to involve experienced utility

  16. Operational Design that Synthesizes Art and Science

    Science.gov (United States)

    2011-05-04

    FINAL 3. DATES COVERED (From - To) Feb - May 2011 4. TITLE AND SUBTITLE OPERATIONAL DESIGN THAT SYNTHESIZES ART AND SCIENCE 5a...TITLE AND SUBTITLE Operational Design That Synthesizes Art And Science 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR...proponents of EBO view warfare as only a science and not a combination of art and science . 9 Another main point of contention centered on the term

  17. Advanced CANDU reactor design for operability

    International Nuclear Information System (INIS)

    Hopwood, J.M.; Lalonde, R.; Soulard, M.

    2003-01-01

    This paper outlines design features and engineering processes in the ACR TM development program which contribute to excellence in performance and low operating cost. AECL recognizes that future plant owners will place a high priority in these operational characteristics. A successful next generation plant will have a best-in-class capability, both in its design characteristics, in the engineering philosophy and program adopted during the product development, and in the vendor's approach to operating station support. The ACR program addresses each of these drivers. Operability considerations are built-in to the design at an overall, plant wide level. For example, based on the strong CANDU 6 operating record, targets for standard outage duration, time between outages and component durability are set, while the design engineering is managed to achieve these targets. The ultimate maintenance target for the ACR, once initial operating experience has been gained, is to operate with a 21-day standard maintenance outage at an interval of once every three years. At the detailed design level, close attention is paid to space allocation, to enable good maintenance access. Selection of components also places emphasis on maintainability based on the extensive and current experience with CANDU projects. (author)

  18. Design of operator interfaces for ''bumpless'' transfers between operator behaviors

    International Nuclear Information System (INIS)

    Lindsay, R.W.; Brown-VanHoozer, S.A.

    1993-01-01

    Advances in the science and art of man-machine interface design have taken major strides forward for interface design practitioners with the advent of the computer. one concern still extant, however, is the need for design of interfaces that minimize confusion when an operator is required to shift from the different levels of cognitive control of skill, rule, and knowledge-based behaviors, (e.g., if an operator is following a set of procedures and a procedural error is noted by the operator, the behavior may, of necessity, shift from rule-based to a knowledge-based behavior). Shifting of the cognitive control levels requires that the information to be displayed to the operator should be designed so that a ''bumpless'' transfer can be made between the behavioral modes, thus reducing the possibility of error. This paper introduces a way to design human interfaces so that skill, rule, and knowledge-based behaviors are supported and provides for the necessary interchanges between behavioral types

  19. Economic aspects of comprehensive mechanization of mining operations. [Poland

    Energy Technology Data Exchange (ETDEWEB)

    Zemla, F

    1978-02-01

    The development of mining equipment for longwall mining and effects of mechanization of mining operations on labor productivity and output of underground coal mines in Poland from 1950 to 1976 are discussed. Mining equipment used from 1950 to 1960 (cutters, steel or timber supports, chain conveyors, drilling and blasting), from 1960 to 1970 (cutter loaders, chain conveyors and steel supports), from 1970 to 1976 (shearer loaders, chain conveyors and powered or shield supports) is analyzed. Coal output of faces mined by mechanized equipment increased from 9.7% in 1950 to 63.1% in 1969 and to 87.6% of total coal output in 1976. The total coal output of underground coal mines increased from 99.1 Mt in 1959 to 125.0 Mt in 1969 and 179.3 Mt in 1976. Labor productivity per miner increased from 1.561 t/d in 1959 to 2.529 t/d in 1969 and to 3.433 t/d in 1976.

  20. Fast-track surgery: Toward comprehensive peri-operative care.

    Science.gov (United States)

    Nanavati, Aditya J; Prabhakar, S

    2014-01-01

    Fast-track surgery is a multimodal approach to patient care using a combination of several evidence-based peri-operative interventions to expedite recovery after surgery. It is an extension of the critical pathway that integrates modalities in surgery, anesthesia, and nutrition, enforces early mobilization and feeding, and emphasizes reduction of the surgical stress response. It entails a great partnership between a surgeon and an anesthesiologist with several other specialists to form a multi-disciplinary team, which may then engage in patient care. The practice of fast-track surgery has yielded excellent results and there has been a significant reduction in hospital stay without a rise in complications or re-admissions. The effective implementation begins with the formulation of a protocol, carrying out each intervention and gathering outcome data. The care of a patient is divided into three phases: Before, during, and after surgery. Each stage needs active participation of few or all the members of the multi-disciplinary team. Other than surgical technique, anesthetic drugs, and techniques form the cornerstone in the ability of the surgeon to carry out a fast-track surgery safely. It is also the role of this team to keep abreast with the latest development in fast-track methodology and make appropriate changes to policy. In the Indian healthcare system, there is a huge benefit that may be achieved by the successful implementation of a fast-track surgery program at an institutional level. The lack of awareness regarding this concept, fear and apprehension regarding its implementation are the main barriers that need to be overcome.

  1. Design and operation of hybrid cooling towers

    International Nuclear Information System (INIS)

    Alt, W.

    1987-01-01

    The first hybrid cooling tower at a coal-fired power station with a waste heat output of 550 MW has been in operation since the middle of 1985. Experience during the construction stage and the initial period of operation has confirmed the correctness of the design standards and of the design itself and, of course, also offers a wealth of knowledge to be observed on future construction projects. A second cooling tower of similar design is being erected at the present time. This cooling tower serves a power station unit with 2500 MW of waste heat output. The programme for this cooling tower offers the possibility for all the accumulated and evaluated experience to be of influence both on the design and also on the method of operation. This paper reports on the details. (orig.) [de

  2. The design of operating procedures manuals for nuclear power plants

    International Nuclear Information System (INIS)

    Bohr, E.; Preuss, W.; Reinartz, G.; Thau, G.

    1977-03-01

    This report describes the findings of a research on the desirable design of operating procedures manuals for nuclear power plants. The work was supported by a grant of the Federal Department of the Interior. Information was acquired from different sources. Interviews and discussions on manual design were carried out with manual users in nuclear power plants. Moreover, tasks carried out using procedures were either observed or, alternatively, the manner of using procedures was elicited by interviews. In addition, manual writers, managers from manufacturers and utilities, nuclear experts, and individuals involved in manual specification activities were interviewed. A major source of information has been the pertinent scientific and technical findings scattered in the literature on topics such as instructional technology, engineering psychology, psycholinguistics, and typography. A comprehensive bibliography is included. General rules are established on designing instructional material for use on the job, aiming at increasing their legability, comprehensibility, and suitability to guide human performance. The application of these rules to the design of individual operating procedures is demonstrated. Recommendations are given on the design, layout, development and implementation of manuals. (orig.) [de

  3. Design basis for the NRC Operations Center

    Energy Technology Data Exchange (ETDEWEB)

    Lindell, M.K.; Wise, J.A.; Griffin, B.N.; Desrosiers, A.E.; Meitzler, W.D.

    1983-05-01

    This report documents the development of a design for a new NRC Operations Center (NRCOC). The project was conducted in two phases: organizational analysis and facility design. In order to control the amount of traffic, congestion and noise within the facility, it is recommended that information flow in the new NRCOC be accomplished by means of an electronic Status Information Management System. Functional requirements and a conceptual design for this system are described. An idealized architectural design and a detailed design program are presented that provide the appropriate amount of space for operations, equipment and circulation within team areas. The overall layout provides controlled access to the facility and, through the use of a zoning concept, provides each team within the NRCOC the appropriate balance of ready access and privacy determined from the organizational analyses conducted during the initial phase of the project.

  4. Design basis for the NRC Operations Center

    International Nuclear Information System (INIS)

    Lindell, M.K.; Wise, J.A.; Griffin, B.N.; Desrosiers, A.E.; Meitzler, W.D.

    1983-05-01

    This report documents the development of a design for a new NRC Operations Center (NRCOC). The project was conducted in two phases: organizational analysis and facility design. In order to control the amount of traffic, congestion and noise within the facility, it is recommended that information flow in the new NRCOC be accomplished by means of an electronic Status Information Management System. Functional requirements and a conceptual design for this system are described. An idealized architectural design and a detailed design program are presented that provide the appropriate amount of space for operations, equipment and circulation within team areas. The overall layout provides controlled access to the facility and, through the use of a zoning concept, provides each team within the NRCOC the appropriate balance of ready access and privacy determined from the organizational analyses conducted during the initial phase of the project

  5. Design and operation of radiation facilities

    International Nuclear Information System (INIS)

    Gay, H.G.

    1983-01-01

    The design, manufacture, and operation of Cobalt-60 Radiation Processing Facilities is a well established technology. However, the products requiring radiation processing are constantly increasing. Product and dose variations create different requirements in the irradiator design. Several basic design concepts which have been developed and installed by Atomic Energy of Canada Limited are discussed. Irradiators are most efficient when designed to handle a limited product density range at an established dose. Requirements for irradiators to process a multitude of different products at different doses leads to a reduction of irradiator efficiency with resultant increase in processing costs

  6. Proximity operations concept design study, task 6

    Science.gov (United States)

    Williams, A. N.

    1990-01-01

    The feasibility of using optical technology to perform the mission of the proximity operations communications subsystem on Space Station Freedom was determined. Proximity operations mission requirements are determined and the relationship to the overall operational environment of the space station is defined. From this information, the design requirements of the communication subsystem are derived. Based on these requirements, a preliminary design is developed and the feasibility of implementation determined. To support the Orbital Maneuvering Vehicle and National Space Transportation System, the optical system development is straightforward. The requirements on extra-vehicular activity are such as to allow large fields of uncertainty, thus exacerbating the acquisition problem; however, an approach is given that could mitigate this problem. In general, it is found that such a system could indeed perform the proximity operations mission requirement, with some development required to support extra-vehicular activity.

  7. CV controls from design to operation

    CERN Document Server

    Blanc, D

    2002-01-01

    The cooling and Ventilation (CV) group has emphasised the need to redefine its organisational structure at the end of 98. The main objective of this operation was to ensure the CV group to be more competitive and efficient through the growing tasks of the LHC projects. The main evolution given to this reorganisation is that the new structure is more project oriented and then operates on three distinct axes: Design, Work and Operation. Process control project management requires a complete and early interaction and participation of all the actors involved. This procedure to be efficient and constructive must be considered and performed not only during the design stage but along the project planning phases and must go beyond the completion work including the process control operation activity. The paper explains the present project management for process control. It describes the present constraints and gives suggestions to a different approach to these projects to improve performances and efficiency of a contr...

  8. Optimization of ejector design and operation

    Directory of Open Access Journals (Sweden)

    Kuzmenko Konstantin

    2016-01-01

    Full Text Available The investigation aims at optimization of gas ejector operation. The goal consists in the improvement of the inflator design so that to enable 50 liters of gas inflation within ~30 milliseconds. For that, an experimental facility was developed and fabricated together with the measurement system to study pressure patterns in the inflator path.

  9. Energy conservation aircraft design and operational procedures

    Energy Technology Data Exchange (ETDEWEB)

    Poisson-Quinton, P.

    1978-01-01

    The paper reviews studies associated with improved fuel efficiency. Several aircraft design concepts are described including: (1) increases in aerodynamic efficiency through decreased friction drag, parasitic drag, and drag due to lift, (2) structural efficiency and the implementation of composite materials, (3) active control technology, (4) the optimization of airframe-engine integration, and (5) VTOL and STOL concepts. Consideration is also given to operational procedures associated with flight management, terminal-area operations, and the influence of environmental noise constraints on fuel economy.

  10. Designing for transportation management and operations : a primer.

    Science.gov (United States)

    2013-02-01

    This primer is focused on the collaborative and systematic consideration of management and operations during transportation : project design and development. This is termed designing for operations. Effectively designing for operations involves...

  11. Environmental design of the Olympic Dam operations

    International Nuclear Information System (INIS)

    Middleton, B.A.

    1989-01-01

    Environmental Design of The Olympic Dam Operations has been required to take into account the Environmental Management Programme as approved by the South Australian Government and radiological protection standards as determined by the Commonwealth of Australia's Code of Practice on Radiation Protection in the Mining and Milling of Radioactive Ores 1987. The article describes the natural environment, project assessment and infrastructure relating to the environmental design. The radiological standards refer to the control of exposure to radiation above naturally occurring background levels both for employees and for members of the public. 2 tabs., maps

  12. Alara applied to iter design and operation

    International Nuclear Information System (INIS)

    Uzan-Elbez, Joelle; Rodriguez-Rodrigo, Lina; Porfiri, Maria Teresa; Taylor, Neil; Gordon, Charles; Garin, Pascal; Girard, Jean-Philippe

    2005-01-01

    Based on the existing data on ITER and the safety options for licensing ITER in Cadarache, the present work assesses the application of the as-low-as-reasonably-achievable (ALARA) principle, as it has been implemented in the design of ITER and will be applied during ITER operation, as well as the compliance of the design with EUR/96-29 directive and regulation applicable in France. The preliminary occupational radiation exposure estimate gives a value of about 250 man mSv/a, which is half the annual target for ITER and comes essentially from maintenance activities. Some examples of the approach are presented

  13. Sustainable Telemedicine: Designing and Building Infrastructure to Support a Comprehensive Telemedicine Practice.

    Science.gov (United States)

    Kreofsky, Beth L H; Blegen, R Nicole; Lokken, Troy G; Kapraun, Susan M; Bushman, Matthew S; Demaerschalk, Bart M

    2018-04-16

    Telemedicine services in medical institutions are often developed in isolation of one another and not as part of a comprehensive telemedicine program. The Center for Connected Care is the administrative home for a broad range of telehealth services at Mayo Clinic. This article speaks of real-time video services, referenced as telemedicine throughout. This article discusses how a large healthcare system designed and built the infrastructure to support a comprehensive telemedicine practice. Based on analysis of existing services, Mayo Clinic developed a multifaceted operational plan that addressed high-priority areas and outlined clear roles and responsibilities of the Center for Connected Care and that of the clinical departments. The plan set priorities and a direction that would lead to long-term success. The plan articulated the governing and operational infrastructure necessary to support telemedicine by defining the role of the Center for Connected Care as the owner of core administrative operations and the role of the clinical departments as the owners of clinical telemedicine services. Additional opportunities were identified to develop product selection processes, implementation services, and staffing models that would be applied to ensure successful telemedicine deployment. The telemedicine team within the Center for Connected Care completed 45 business cases resulting in 54 implementations. The standardization of core products along with key operational offerings around implementation services, and the establishment of a 24/7 support model resulted in improved provider satisfaction and fewer reported technical issues. The foundation for long-term scalability and growth was developed by centralizing operations of telemedicine services, implementing sustainable processes, employing dedicated qualified personnel, and deploying robust products.

  14. Circulating fluidized bed boilers design and operations

    CERN Document Server

    Basu, Prabir

    1991-01-01

    This book provides practicing engineers and students with insight into the design and operation of circulating fluidized bed (CFB) boilers. Through a combination of theoretical concepts and practical experience, this book gives the reader a basic understanding of the many aspects of this subject.Important environmental considerations, including solid waste disposal and predicted emissions, are addressed individually in separate chapters. This book places an emphasis on combustion, hydrodynamics, heat transfer, and material issues, and illustrates these concepts with numerous examples of pres

  15. An operating nuclear utility's experience with the ALARA design of a new nuclear unit

    International Nuclear Information System (INIS)

    Rodgers, R.C.

    1985-01-01

    This talk presents a review of how operating experience at Northeast Utilities has been factored into the design of a new nuclear unit and the development and management of the radiation protection program. Their operational experience has indicated that there are two facets to keeping radiation exposures ALARA. The first is the proper ALARA design of the unit. The other facet is the design of a comprehensive radiation protection program. The author discusses these facets in some detail

  16. Small sodium valve design and operating experience

    International Nuclear Information System (INIS)

    McGough, C.B.

    1974-01-01

    The United States Liquid Metal Fast Breeder Reactor program (LMFBR) includes an extensive program devoted to the development of small sodium valves. This program is now focused on the development and production of valves for the Fast Flux Test Facility (FFTF) now under construction near Richland, Washington. Other AEC support facilities, such as various test loops located at the Liquid Metal Engineering Center (LMEC), Los Angeles, California, and at the Hanford Engineering Development Laboratory (HEDL), Richland, Washington, also have significant requirements for small sodium valves, and valves similar in design to the FFTF valves are being supplied to these AEC laboratories for use in their critical test installations. A principal motivation for these valve programs, beyond the immediate need to provide high-reliability valves for FFTF and the support facilities, is the necessity to develop small valve technology for the Clinch River Breeder Reactor Plant (CRBRP). FFTF small sodium valve design and development experience will be directly applied to the CRBRP program. Various test programs have been, and are being, conducted to verify the performance and integrity of the FFTF valves, and to uncover any potential problems so that they can be corrected before the valves are placed in service in FFTF. The principal small sodium valve designs being utilized in current U.S. programs, the test and operational experience obtained to date on them, problems uncovered, and future development and testing efforts being planned are reviewed. The standards and requirements to which the valves are being designed and fabricated, the valve designs in current use, valve operators, test and operating experience, and future valve development plans are summarized. (U.S.)

  17. Practical applications of technica data to waterflood design and operation

    Energy Technology Data Exchange (ETDEWEB)

    Greenwell, H E

    1965-03-01

    Two principles must be applied to the practical use of technical data in designing and operating water injection systems. The first is that corrosion must be tied inseparably to considerations of injection well plugging. Corrosion and plugging represent a single problem. This problem may be solved by applying research information to system conditions of water source. The second principle that must be applied is that current, past, and future results of research in this area can be utilized most directly by first measuring the conditions that actually exist in the system, or in the source water. Two things must be known: contents and composition of all materials not in solution under system conditions; and relatively comprehensive analyses of the water. They are needed for each water source and at each point in the system where some change could be occurring. These studies will generally disclose practical operating requirements.

  18. The EPR-a comprehensive design concept against external events

    International Nuclear Information System (INIS)

    Stoll, U.; Waas, U.

    2006-01-01

    The main objective of design provisions against external hazards is to ensure that the safety functions required to bring the plant to safe shutdown are not inadmissibly affected by any external hazards that might be postulated for the intended site of the plant. In the design of the European Pressurized Water Reactor (EPR) particular attention was paid to external hazards such as earthquake, airplane crash, and explosion pressure wave. The standard EPR covers a large range of possible site conditions, the design earthquake enveloping safe shutdown earthquakes (SSE) to be expected for potential sites. The loads for the design basis airplane crash and - if required - for the design extension airplane crash as well as for external Explosion Pressure Wave are defined depending on site specific requirements. Protection against other external load cases such as extreme winds and external flooding is also included in the standard design

  19. Design and Operation of Distribution Markets

    Science.gov (United States)

    Parhizi, Sina

    in the electricity markets, and an analytical model is presented for design and operation of such markets.

  20. Facilitating Comprehension, Connection and Commitment to Environmentally Responsible Design

    Science.gov (United States)

    Boehm, Sarah

    2015-01-01

    Given the increased awareness of the negative effects the building industry has on the environment, designs produced without considering sustainability of the planet can no longer be accepted. Although the concepts of sustainability and environmental responsibility are not new to the field of interior design, a review of the literature reveals…

  1. The EPR-a comprehensive design concept against external events

    International Nuclear Information System (INIS)

    Waas, U.; Stoll, U.

    2005-01-01

    The main objective of design provisions against external hazards is to ensure that the safety functions required to bring the plant to safe shutdown are not inadmissible affected. In the design of the EPR particular attention was paid to the following external hazards: Earthquake, Airplane crash, Explosion pressure wave. The design concept for these events is discussed below. The standard EPR covers a large range of possible site conditions, the design earthquake enveloping safe shutdown earthquakes (SSE) to be expected for potential sites. The Basic Design was developed for the seismic loads given in the European Utility Requirements with a horizontal free field Peak Ground Acceleration (PGA) for all site conditions of 0.25 g. The seismic protection is based on a deterministic design approach, with the intention of ensuring the safety functions in case of SSE. The loads for the design basis airplane crash and - if required - for the design extension airplane crash are defined depending on site specific requirements. For the design basis airplane crash as defined in Finland the safety goals are fulfilled for postulated single failure and preventive maintenance as well as for specific unlikely scenarios with local impacts where one redundant train is assumed to be lost. For the design extension airplane crash no single failure and preventive maintenance are assumed. Reactor building (RB), fuel building (FB), safeguard building (SB) 2 and 3 are protected by design against airplane crash. The common base mat of the RB, FB and SBs ensures global stability. To avoid penetration the wall thickness of the outer building structures of RB, FB and SB2/3 is set at 1.80 m (result of an optimization process). To rule out major induced vibrations due to airplane crash the inner building structures are decoupled from the outer walls. The SB 1 and SB4, the main steam and feedwater valve compartments, the diesel buildings and the service water pump buildings are protected against

  2. A Comprehensive Framework for Evaluation in Design Science Research

    DEFF Research Database (Denmark)

    Pries-Heje, Jan; Baskerville, Richard; Venable, John

    2012-01-01

    Evaluation is a central and essential activity in conducting rigorous Design Science Research (DSR), yet there is surprisingly little guidance about designing the DSR evaluation activity beyond suggesting possible methods that could be used for evaluation. This paper extends the notable exception...... of the existing framework of Pries-Heje et al [11] to address this problem. The paper proposes an extended DSR evaluation framework together with a DSR evaluation design method that can guide DSR researchers in choosing an appropriate strategy for evaluation of the design artifacts and design theories that form...... the output from DSR. The extended DSR evaluation framework asks the DSR researcher to consider (as input to the choice of the DSR evaluation strategy) contextual factors of goals, conditions, and constraints on the DSR evaluation, e.g. the type and level of desired rigor, the type of artifact, the need...

  3. The design process of a reading comprehension manual

    Directory of Open Access Journals (Sweden)

    Sergio Alonso Lopera Medina

    2015-05-01

    Full Text Available Material design is an important part in the teaching practices. This article describes the process of material design of a foreign language (FL reading manual for undergraduate students at Universidad de Antioquia (Medellín – Colombia. A case study was used as a research method. Four in-service English teachers based their inquiry following the reflective approach of professional development. They also took into account the guidelines to design teaching materials proposed by Howard and Major (2004.  Some of the results of their inquiry for the design of the manual involve contextualization, personalization, and students’ needs. A sample of a reading strategy is given in order to illustrate how teachers worked and designed the manual as a product of their inquiry. Conclusions suggest that this professional development practice helped teachers become more aware of their own teaching realities and also helped them to understand their beliefs and practice in teaching reading as a foreign language.

  4. SWR 1000: Efficient design for operational excellence

    International Nuclear Information System (INIS)

    Brettschuh, W.

    2008-01-01

    The SWR 1000 boiling water reactor (BWR) offers all of the advantages associated with an advanced plant design, i.e. excellent safety performance and competitive power generation costs, in the medium capacity range (1000-1250 MW). The economic efficiency of this medium-sized plant in comparison with large-capacity designs is achieved by using very simple passive safety equipment, simplified plant operating systems, and a very simple plant configuration. Systems engineering is thus optimized, reducing dependence on electrical and instrumentation and control (I and C) systems. The fuel assemblies deployed in the SWR 1000 core are enlarged from a 10 x 10 to a 12 x 12 rod array. This cuts down the total number of fuel assemblies in the core and hence also the number of control rods and control rod drives, as well as in-core neutron flux monitors. The design owes its competitiveness to the fact that investment, maintenance and fuel cycle costs are all lower. In addition, refueling outages are shorter, thanks to the reduced scope for outage activities. For example, there are no bolted reactor internal joints, and the SWR 1000 has a permanently installed reactor vessel-to-drywell seal. Replacement of in-core detectors is carried out from below, and does not affect the critical path of the outage. Furthermore all in-service -inspections (ISIs) on the reactor pressure vessel (RPV) and its nozzles can be undertaken from the outside, so that no extended ISI outages are necessary. As in existing plants, forced coolant circulation is utilized, ensuring problem-free startup and enabling plant operators to adjust power rapidly in the high power range (70%-100%). This is achieved without moving the control rods, and allows both spectral-shift and stretch-out operation. The considerable gains provided by forced coolant circulation, in terms of operational flexibility and fuel utilization, mean that the investment and maintenance costs of the pumps are covered within just a few

  5. 46 CFR 109.527 - Cranes: Operator designation.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Cranes: Operator designation. 109.527 Section 109.527... OPERATIONS Cranes § 109.527 Cranes: Operator designation. (a) The master or person in charge shall designate, in writing, each crane operator. (b) The master or person in charge shall ensure that only designated...

  6. Biogas plants: Design, construction and operation

    International Nuclear Information System (INIS)

    2001-01-01

    At the big readiness of waste coming from the agricultural activities are looked for the production of Energy and Payments, the biogas like product of the organic decomposition under anaerobic conditions, their composition and characteristic. The elements that conform the design as the digester, the storage, the load tanks and it discharges and the conduction is described and analyzed. They are given a series of elements to obtain the characteristics of the system possible to place as: planning, calculations, evaluation, execution and operation. Lastly the steps are indicated that should be continued in the construction of the plant including planning for the work

  7. Theory, design, and operation of liquid metal fast breeder reactors, including operational health physics

    International Nuclear Information System (INIS)

    Adams, S.R.

    1985-10-01

    A comprehensive evaluation was conducted of the radiation protection practices and programs at prototype LMFBRs with long operational experience. Installations evaluated were the Fast Flux Test Facility (FFTF), Richland, Washington; Experimental Breeder Reactor II (EBR-II), Idaho Falls, Idaho; Prototype Fast Reactor (PFR) Dounreay, Scotland; Phenix, Marcoule, France; and Kompakte Natriumgekuhlte Kernreak Toranlange (KNK II), Karlsruhe, Federal Republic of Germany. The evaluation included external and internal exposure control, respiratory protection procedures, radiation surveillance practices, radioactive waste management, and engineering controls for confining radiation contamination. The theory, design, and operating experience at LMFBRs is described. Aspects of LMFBR health physics different from the LWR experience in the United States are identified. Suggestions are made for modifications to the NRC Standard Review Plan based on the differences

  8. Theory, design, and operation of liquid metal fast breeder reactors, including operational health physics

    Energy Technology Data Exchange (ETDEWEB)

    Adams, S.R.

    1985-10-01

    A comprehensive evaluation was conducted of the radiation protection practices and programs at prototype LMFBRs with long operational experience. Installations evaluated were the Fast Flux Test Facility (FFTF), Richland, Washington; Experimental Breeder Reactor II (EBR-II), Idaho Falls, Idaho; Prototype Fast Reactor (PFR) Dounreay, Scotland; Phenix, Marcoule, France; and Kompakte Natriumgekuhlte Kernreak Toranlange (KNK II), Karlsruhe, Federal Republic of Germany. The evaluation included external and internal exposure control, respiratory protection procedures, radiation surveillance practices, radioactive waste management, and engineering controls for confining radiation contamination. The theory, design, and operating experience at LMFBRs is described. Aspects of LMFBR health physics different from the LWR experience in the United States are identified. Suggestions are made for modifications to the NRC Standard Review Plan based on the differences.

  9. The evolution of NATO’s comprehensive approach to crisis management operations

    Directory of Open Access Journals (Sweden)

    Guillem Colom Piella

    2012-04-01

    Full Text Available The crisis management operations, post-war stabilisation and nation-building that has taken place since the end of the Cold War has all highlighted the extreme need to harmonise multinational and inter-agency cooperation in order to increase the coherence and effectiveness of the operation. That is the basic principle of Comprehensive Approach, which is defined as the coordination of strategies and actions of the participating actors in crisis management and at all levels, stages and planes of same. The NATO has also incorporated these advances into the area of crisis management, as a result of which, since 2006, it has been defining its own concept of Comprehensive Approach for non-Article 5 missions, and as a central theme in its political-military strategy for the present and immediate future.

  10. Extraneous Information and Graph Comprehension: Implications for Effective Design Choices

    Science.gov (United States)

    Stewart, Brandie M.; Cipolla, Jessica M.; Best, Lisa A.

    2009-01-01

    Purpose: The purpose of this paper is to examine if university students could accurately extract information from graphs presented in 2D or 3D formats with different colour hue variations or solid black and white. Design/methodology/approach: Participants are presented with 2D and 3D bar and pie charts in a PowerPoint presentation and are asked to…

  11. Comprehensive Educational Assessment for the States: The Duplex Design.

    Science.gov (United States)

    Bock, R. Darrell; Mislevy, Robert

    State testing programs often attempt to provide annual information for use in student guidance and qualification, school and program evaluation, and broad policy decisions. With the development of a new type of assessment instrument, the "duplex design," the several functions of state testing programs can be served in a single test…

  12. Comprehensive Test Ban Treaty (CTBT) monitoring station operating regime influence on radionuclide detection sensitivity

    International Nuclear Information System (INIS)

    Williams, D.L.

    1999-01-01

    International Monitoring System (IMS) stations are being deployed worldwide in support of the Comprehensive [Nuclear] Test Ban Treaty (CTBT). The highly sensitive radionuclide monitoring stations regularly sample airborne radionuclide particulates to determine whether fission products are present in the atmosphere that may be indicative of a nuclear weapons test. Standards have been set for these stations regarding their operation regime and the minimum detectable concentrations (MDCs) for specific radionuclides likely to be present after a nuclear weapons test. This study uses actual CTBT monitoring data to relate a subset of the specified operational standards with the listed MDC limits. It is determined that a relationship exists between the specified operational regime and the MDC values. Since the background radioactivity is largely a function of the radon and thoron progeny, longer decay operational regimes allow for a reduction in the background. For longer lived radionuclides, this corresponds to a reduction in MDC. (author)

  13. Buffer mass test - Heater design and operation

    International Nuclear Information System (INIS)

    Nilsson, J.; Ramqvist, G.; Pusch, R.

    1984-06-01

    The nuclear waste is assumed to be contained in cylindrical metal canisters which will be inserted in deposition holes. Heat is generated as a result of the continuing decay of the radioactive waste and in the Buffer Mass Test (BMT) the heat flux expected from such canisters was simulated by the use of six electric heaters. the heaters were constructed partly of aluminium and partly of stainless steel. They are 1520 mm in length and 380 mm in diameter, and give a maximum power output of 3000 W. The heater power can be monitored by panel meters coupled to a computer-based data acquisition system. Both the heater and the control system were manufactured with a high degree of redundancy in case of component failure. This report describes the design, construction, testing, installation and necessary tools for heater installation and dismantling operation. (author)

  14. Cooling tower drift: experiment design for comprehensive case study

    International Nuclear Information System (INIS)

    Laulainen, N.S.

    1978-01-01

    A drift experiment program to develop a data base which can be used for validation of drift deposition models has been formulated. The first field effort is designed for a suitable mechanical-draft cooling tower to be selected after site visits have been conducted. The discussion here demonstrates the importance of characterizing the droplet size spectrum emitted from the tower and to accurately account for droplet evaporation, because the downwind droplet deposition patterns and near-surface airborne concentrations are extremely sensitive to these parameters

  15. Operational resilience: concepts, design and analysis

    Science.gov (United States)

    Ganin, Alexander A.; Massaro, Emanuele; Gutfraind, Alexander; Steen, Nicolas; Keisler, Jeffrey M.; Kott, Alexander; Mangoubi, Rami; Linkov, Igor

    2016-01-01

    Building resilience into today’s complex infrastructures is critical to the daily functioning of society and its ability to withstand and recover from natural disasters, epidemics, and cyber-threats. This study proposes quantitative measures that capture and implement the definition of engineering resilience advanced by the National Academy of Sciences. The approach is applicable across physical, information, and social domains. It evaluates the critical functionality, defined as a performance function of time set by the stakeholders. Critical functionality is a source of valuable information, such as the integrated system resilience over a time interval, and its robustness. The paper demonstrates the formulation on two classes of models: 1) multi-level directed acyclic graphs, and 2) interdependent coupled networks. For both models synthetic case studies are used to explore trends. For the first class, the approach is also applied to the Linux operating system. Results indicate that desired resilience and robustness levels are achievable by trading off different design parameters, such as redundancy, node recovery time, and backup supply available. The nonlinear relationship between network parameters and resilience levels confirms the utility of the proposed approach, which is of benefit to analysts and designers of complex systems and networks.

  16. Integrated safeguards and facility design and operations

    International Nuclear Information System (INIS)

    Tape, J.W.; Coulter, C.A.; Markin, J.T.; Thomas, K.E.

    1987-01-01

    The integration of safeguards functions to deter or detect unauthorized actions by an insider requires the careful communication and management of safeguards-relevant information on a timely basis. The traditional separation of safeguards functions into physical protection, materials control, and materials accounting often inhibits important information flows. Redefining the major safeguards functions as authorization, enforcement, and verification, and careful attention to management of information from acquisition to organization, to analysis, to decision making can result in effective safeguards integration. The careful inclusion of these ideas in facility designs and operations will lead to cost-effective safeguards systems. The safeguards authorization function defines, for example, personnel access requirements, processing activities, and materials movements/locations that are permitted to accomplish the mission of the facility. Minimizing the number of authorized personnel, limiting the processing flexibility, and maintaining up-to-date flow sheets will facilitate the detection of unauthorized activities. Enforcement of the authorized activities can be achieved in part through the use of barriers, access control systems, process sensors, and health and safety information. Consideration of safeguards requirements during facility design can improve the enforcement function. Verification includes the familiar materials accounting activities as well as auditing and testing of the other functions

  17. Design and validation of a comprehensive fecal incontinence questionnaire.

    Science.gov (United States)

    Macmillan, Alexandra K; Merrie, Arend E H; Marshall, Roger J; Parry, Bryan R

    2008-10-01

    Fecal incontinence can have a profound effect on quality of life. Its prevalence remains uncertain because of stigma, lack of consistent definition, and dearth of validated measures. This study was designed to develop a valid clinical and epidemiologic questionnaire, building on current literature and expertise. Patients and experts undertook face validity testing. Construct validity, criterion validity, and test-retest reliability was undertaken. Construct validity comprised factor analysis and internal consistency of the quality of life scale. The validity of known groups was tested against 77 control subjects by using regression models. Questionnaire results were compared with a stool diary for criterion validity. Test-retest reliability was calculated from repeated questionnaire completion. The questionnaire achieved good face validity. It was completed by 104 patients. The quality of life scale had four underlying traits (factor analysis) and high internal consistency (overall Cronbach alpha = 0.97). Patients and control subjects answered the questionnaire significantly differently (P validity testing. Criterion validity assessment found mean differences close to zero. Median reliability for the whole questionnaire was 0.79 (range, 0.35-1). This questionnaire compares favorably with other available instruments, although the interpretation of stool consistency requires further research. Its sensitivity to treatment still needs to be investigated.

  18. Association of pre-operative medication use with post-operative delirium in surgical oncology patients receiving comprehensive geriatric assessment.

    Science.gov (United States)

    Jeong, Young Mi; Lee, Eunsook; Kim, Kwang-Il; Chung, Jee Eun; In Park, Hae; Lee, Byung Koo; Gwak, Hye Sun

    2016-07-07

    Older patients undergoing surgery tend to have a higher frequency of delirium. Delirium is strongly associated with poor surgical outcomes. This study evaluated the association between pre-operative medication use and post-operative delirium (POD) in surgical oncology patients receiving comprehensive geriatric assessment (CGA). A total of 475 patients who were scheduled for cancer surgery and received CGA from January 2014 to June 2015 were included. Pre-operative medication review through CGA was conducted on polypharmacy (≥5 medications), delirium-inducing medications (DIMs), fall-inducing medications (FIMs), and potentially inappropriate medications (PIMs). POD was confirmed by psychiatric consultation, and DSM-V criteria were used for diagnosing delirium. The model fit of the prediction model was assessed by computing the Hosmer-Lemeshow goodness-of-fit test. Effect size was measured using the Nagelkerke R(2). Discrimination of the model was assessed by an analysis of the area under receiver operating curve (AUROC). Two models were constructed for multivariate analysis based on univariate analysis; model I included dementia and DIM in addition to age and sex, and model II included PIM instead of DIM of model I. Every one year increase of age increased the risk of POD by about 1.1-fold. DIM was a significant factor for POD after adjusting for confounders (AOR 12.78, 95 % CI 2.83-57.74). PIM was also a significant factor for POD (AOR 5.53, 95 % CI 2.03-15.05). The Hosmer-Lemeshow test results revealed good fits for both models (χ(2) = 3.842, p = 0.871 for model I and χ(2) = 8.130, p = 0.421 for model II). The Nagelkerke R(2) effect size and AUROC for model I was 0.215 and 0.833, respectively. Model II had the Nagelkerke R(2)effect size of 0.174 and AUROC of 0.819. These results suggest that pharmacists' comprehensive review for pre-operative medication use is critical for the post-operative outcomes like delirium in older patients.

  19. Deep Learning Object-Recognition in a Design-to-Robotic-Production and -Operation Implementation

    NARCIS (Netherlands)

    Liu Cheng, A.; Bier, H.H.; Mostafavi, S.S.

    2017-01-01

    This paper presents a new instance in a series of discrete proof-of-concept implementations of comprehensively intelligent built-environments based on Design-to-Robotic-Production and -Operation (D2RP&O) principles developed at Delft University of Technology (TUD). With respect to D2RP, the

  20. Sodium Fire Demonstration Facility Design and Operation

    International Nuclear Information System (INIS)

    Cho, Youngil; Kim, Jong-Man; Lee, Jewhan; Hong, Jonggan; Yeom, Sujin; Cho, Chungho; Jung, Min-Hwan; Gam, Da-Young; Jeong, Ji-Young

    2014-01-01

    Although sodium has good characteristics such as high heat transfer rate and stable nuclear property, it is difficult to manage because of high reactivity. Sodium is solid at the room temperature and it easily reacts with oxygen resulting in fire due to the reaction heat. Thus, sodium must be stored in a chemically stable place, i.e., an inert gas-sealed or oil filled vessel. When a sodium fire occurs, the Na 2 O of white fume is formed. It is mainly composed of Na 2 O 2 , NaOH, and Na 2 CO 3 , ranging from 0.1 to several tens of micrometers in size. It is known that the particle size increases by aggregation during floating in air. Thus, the protection method is important and should be considered in the design and operation of a sodium system. In this paper, sodium fire characteristics are described, and the demonstration utility of outbreak of sodium fire and its extinguishing is introduced. In this paper, sodium fire characteristics and a demonstration facility are described. The introduced sodium fire demonstration facility is the only training device used to observe a sodium fire and extinguish it domestically. Furthermore, the type of sodium fire will be diversified with the enhancement of the utility. It is expected that this utility will contribute to experience in the safe treatment of sodium by the handlers

  1. Cloud Computing for Mission Design and Operations

    Science.gov (United States)

    Arrieta, Juan; Attiyah, Amy; Beswick, Robert; Gerasimantos, Dimitrios

    2012-01-01

    The space mission design and operations community already recognizes the value of cloud computing and virtualization. However, natural and valid concerns, like security, privacy, up-time, and vendor lock-in, have prevented a more widespread and expedited adoption into official workflows. In the interest of alleviating these concerns, we propose a series of guidelines for internally deploying a resource-oriented hub of data and algorithms. These guidelines provide a roadmap for implementing an architecture inspired in the cloud computing model: associative, elastic, semantical, interconnected, and adaptive. The architecture can be summarized as exposing data and algorithms as resource-oriented Web services, coordinated via messaging, and running on virtual machines; it is simple, and based on widely adopted standards, protocols, and tools. The architecture may help reduce common sources of complexity intrinsic to data-driven, collaborative interactions and, most importantly, it may provide the means for teams and agencies to evaluate the cloud computing model in their specific context, with minimal infrastructure changes, and before committing to a specific cloud services provider.

  2. Designing information visualizations for elite soccer children's different levels of comprehension

    DEFF Research Database (Denmark)

    Herdal, Thor; Pedersen, Jeppe Gerner; Knudsen, Søren

    2016-01-01

    We describe a study that sought to understand elite soccer children's use of visualizations to learn about, and improve their own sports performance. We specifically investigate how visualizations support the players' data comprehension. In this process, we design and evaluate visualizations base...... on real data. Finally, we discuss how the players' level of comprehension might depend on factors such as their general literacy and visualization literacy, and the role of visualization in coaching children....

  3. [A comprehensive approach to designing of magnetotherapy techniques based on the Atos device].

    Science.gov (United States)

    Raĭgorodskiĭ, Iu M; Semiachkin, G P; Tatarenko, D A

    1995-01-01

    The paper determines how to apply a comprehensive approach to designing magnetic therapeutical techniques based on concomitant exposures to two or more physical factors. It shows the advantages of the running pattern of a magnetic field and photostimuli in terms of optimization of physiotherapeutical exposures. An Atos apparatus with an Amblio-1 attachment is used as an example to demonstrate how to apply the comprehensive approach for ophthalmology.

  4. Design of JRR-4 operation Supporting System

    International Nuclear Information System (INIS)

    Takahashi, Hiroki; Arai, Nobuyoshi; Yamamoto, Kazuyoshi; Yoritsune, Tsutomu

    1999-01-01

    A work on the Japan Research Reactor No. 4 (JRR-4) core modification from high-enriched fuels to low-enriched ones was started in 1996 and completed in May 1998. As a part of the work, Operation Supporting System (OSS) was adopted for the purpose of reducing load of operator, preventing operator's error and supplying operation data to users. As the result of adopting this system, integrated monitoring, automation of part of reactor operation and data management were realized. In addition, the cooling control system was compacted. (author)

  5. A Study of Wind Turbine Comprehensive Operational Assessment Model Based on EM-PCA Algorithm

    Science.gov (United States)

    Zhou, Minqiang; Xu, Bin; Zhan, Yangyan; Ren, Danyuan; Liu, Dexing

    2018-01-01

    To assess wind turbine performance accurately and provide theoretical basis for wind farm management, a hybrid assessment model based on Entropy Method and Principle Component Analysis (EM-PCA) was established, which took most factors of operational performance into consideration and reach to a comprehensive result. To verify the model, six wind turbines were chosen as the research objects, the ranking obtained by the method proposed in the paper were 4#>6#>1#>5#>2#>3#, which are completely in conformity with the theoretical ranking, which indicates that the reliability and effectiveness of the EM-PCA method are high. The method could give guidance for processing unit state comparison among different units and launching wind farm operational assessment.

  6. Comprehensive Surgical Coaching Enhances Surgical Skill in the Operating Room: A Randomized Controlled Trial.

    Science.gov (United States)

    Bonrath, Esther M; Dedy, Nicolas J; Gordon, Lauren E; Grantcharov, Teodor P

    2015-08-01

    The aim of the study was to determine whether individualized coaching improved surgical technical skill in the operating room to a higher degree than current residency training. Clinical training in the operating room is a valuable opportunity for surgeons to acquire skill and knowledge; however, it often remains underutilized. Coaching has been successfully used in various industries to enhance performance, but its role in surgery has been insufficiently investigated. This randomized controlled trial was conducted at one surgical training program. Trainees undergoing a minimally invasive surgery rotation were randomized to either conventional training (CT) or comprehensive surgical coaching (CSC). CT included ward and operating room duties, and regular departmental teaching sessions. CSC comprised performance analysis, debriefing, feedback, and behavior modeling. Primary outcome measures were technical performance as measured on global and procedure-specific rating scales, and surgical safety parameters, measured by error count. Operative performance was assessed by blinded video analysis of the first and last cases recorded by the participants during their rotation. Twenty residents were randomized and 18 completed the study. At posttraining the CSC group (n = 9) scored significantly higher on a procedure-specific skill scale compared with the CT group (n = 9) [median, 3.90 (interquartile range, 3.68-4.30) vs 3.60 (2.98-3.70), P = 0.017], and made fewer technical errors [10 (7-13) vs 18 (13-21), P = 0.003]. Significant within-group improvements for all skill metrics were only noted in the CSC group. Comprehensive surgical coaching enhances surgical training and results in skill acquisition superior to conventional training.

  7. A comprehensive study of different gases in inductively coupled plasma torch operating at one atmosphere

    International Nuclear Information System (INIS)

    Punjabi, Sangeeta B.; Joshi, N. K.; Mangalvedekar, H. A.; Lande, B. K.; Das, A. K.; Kothari, D. C.

    2012-01-01

    A numerical study is done to understand the possible operating regimes of RF-ICP torch (3 MHz, 50 kW) using different gases for plasma formation at atmospheric pressure. A two dimensional numerical simulation of RF-ICP torch using argon, nitrogen, oxygen, and air as plasma gas has been investigated using computational fluid dynamic (CFD) software fluent (c) . The operating parameters varied here are central gas flow, sheath gas flow, RF-power dissipated in plasma, and plasma gas. The temperature contours, flow field, axial, and radial velocity profiles were investigated under different operating conditions. The plasma resistance, inductance of the torch, and the heat distribution for various plasma gases have also been investigated. The plasma impedance of ICP torch varies with different operating parameters and plays an important role for RF oscillator design and power coupling. These studies will be useful to decide the design criteria for ICP torches required for different material processing applications.

  8. Systemic Operational Design: Bringing Efficacy to the Operational Level of War

    National Research Council Canada - National Science Library

    Bernard, Barrett M

    2007-01-01

    The premise of this monograph is that the Elements of Operational Design are incapable of linking the tactical employment of forces to strategic objectives and that Systemic Operational Design is a viable alternative...

  9. Ecological Equivalence Assessment Methods: What Trade-Offs between Operationality, Scientific Basis and Comprehensiveness?

    Science.gov (United States)

    Bezombes, Lucie; Gaucherand, Stéphanie; Kerbiriou, Christian; Reinert, Marie-Eve; Spiegelberger, Thomas

    2017-08-01

    In many countries, biodiversity compensation is required to counterbalance negative impacts of development projects on biodiversity by carrying out ecological measures, called offset when the goal is to reach "no net loss" of biodiversity. One main issue is to ensure that offset gains are equivalent to impact-related losses. Ecological equivalence is assessed with ecological equivalence assessment methods taking into account a range of key considerations that we summarized as ecological, spatial, temporal, and uncertainty. When equivalence assessment methods take into account all considerations, we call them "comprehensive". Equivalence assessment methods should also aim to be science-based and operational, which is challenging. Many equivalence assessment methods have been developed worldwide but none is fully satisfying. In the present study, we examine 13 equivalence assessment methods in order to identify (i) their general structure and (ii) the synergies and trade-offs between equivalence assessment methods characteristics related to operationality, scientific-basis and comprehensiveness (called "challenges" in his paper). We evaluate each equivalence assessment methods on the basis of 12 criteria describing the level of achievement of each challenge. We observe that all equivalence assessment methods share a general structure, with possible improvements in the choice of target biodiversity, the indicators used, the integration of landscape context and the multipliers reflecting time lags and uncertainties. We show that no equivalence assessment methods combines all challenges perfectly. There are trade-offs between and within the challenges: operationality tends to be favored while scientific basis are integrated heterogeneously in equivalence assessment methods development. One way of improving the challenges combination would be the use of offset dedicated data-bases providing scientific feedbacks on previous offset measures.

  10. Autonomous Operations Design Guidelines for Flight Hardware

    Data.gov (United States)

    National Aeronautics and Space Administration — SSC experimentally modified an autonomous operations flexible system suite developed for a ground application for a flight system under development by JSC. The...

  11. Quantum Operator Design for Lattice Baryon Spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Lichtl, Adam [Carnegie Mellon Univ., Pittsburgh, PA (United States)

    2006-09-07

    A previously-proposed method of constructing spatially-extended gauge-invariant three-quark operators for use in Monte Carlo lattice QCD calculations is tested, and a methodology for using these operators to extract the energies of a large number of baryon states is developed. This work is part of a long-term project undertaken by the Lattice Hadron Physics Collaboration to carry out a first-principles calculation of the low-lying spectrum of QCD. The operators are assemblages of smeared and gauge-covariantly-displaced quark fields having a definite flavor structure. The importance of using smeared fields is dramatically demonstrated. It is found that quark field smearing greatly reduces the couplings to the unwanted high-lying short-wavelength modes, while gauge field smearing drastically reduces the statistical noise in the extended operators.

  12. LOFT fuel design and operating experience

    International Nuclear Information System (INIS)

    Russell, M.L.

    1979-01-01

    The objective of the LOFT fuel design and fabrication effort was to provide a pressurized water reactor core that has (1) materials and geometric features to ensure that heat transfer, hydraulic, mechanical, chemical, metallurgical and nuclear behaviors are typical of large pressurized water reactors (PWR) during the loss-of-coolant accident (LOCA) sequence and (2) test instrumentation for measurement of core conditions. The LOFT core is unique because it is designed for exposure to several LOCAs without loss of function. This paper summarizes the design effort and extent to which the design objectives have been achieved

  13. Database/Operating System Co-Design

    OpenAIRE

    Giceva, Jana

    2016-01-01

    We want to investigate how to improve the information flow between a database and an operating system, aiming for better scheduling and smarter resource management. We are interested in identifying the potential optimizations that can be achieved with a better interaction between a database engine and the underlying operating system, especially by allowing the application to get more control over scheduling and memory management decisions. Therefore, we explored some of the issues that arise ...

  14. Exploration on the matching between Optical Comprehensive Design Experiment and Washington Accord

    Science.gov (United States)

    Cao, Yiping; Chen, Wenjing; Zhang, Qican; Liu, Yuankun; Li, Dahai; Zhou, Xinzhi; Wei, Jun

    2017-08-01

    Common problems faced in optical comprehensive design experiment and going against the Washington Accord are pointed out. For resolving these problems, an instructional and innovative teaching scheme for Optics Comprehensive Design Experiment is proposed. We would like to understand the student that can improve the hands-on practical ability, theory knowledge understanding ability, complex problem solving ability, engineering application ability, cooperative ability after tracking and researching the student who have attended the class about Optical Comprehensive Design Experiment, We found that there are some problems on the course such as the experiment content vague, the student beginning less time, phase separation theory and engineering application, the experiment content lack of selectivity and so on. So we have made some improvements reference to the Washington Accord for the class teaching plan about Optical Comprehensive Design Experiment. This class must relevant to the engineering basic courses, professional foundation course and the major courses, so far as to the future study and work that which can play a role in inheriting and continuity to the students. The Optical Comprehensive Design Experiment teaching program requires students learning this course to have learnt basic courses like analog electronics technique, digital electronic technique, applied optics and computer and other related courses which students are required to comprehensively utilize. This teaching scheme contains six practical complex engineering problems which are respectively optical system design, light energy meter design, illuminometer design, material refractive index measuring system design, light intensity measuring system design and open design. Establishing the optional experiment and open experiment can provide students with a greater choice and enhance the students' creativity, vivid teaching experimental teachers and enriching contents of experiment can make the

  15. Considerations regarding design of ion exchange columns for applications in heavy water nuclear reactors- a comprehensive review

    International Nuclear Information System (INIS)

    Joginder Kumar; Nema, M.K.

    2000-01-01

    In nuclear reactor applications the principal role of the purification system is to maintain a satisfactory chemistry of moderator and coolant which are different at various stages of reactor operations e.g. during reactor start up, for removal of neutron poison from the moderator, the purification flows are much different compared to steady state operation of the reactor. In order to cater to varying requirements regarding purification load, optimisation in connection with ion exchange column design plays an important role and becomes very challenging in Heavy Water Nuclear Reactors mainly due to the fact that heavy water is very very expensive. In this paper a comprehensive review is made for various designs adopted so far regarding IX column in Indian PHWRs of 220 MWe size for normal operations. Design and operating experience regarding large size IX column used for occasional needs during dilute chemical decontamination of 220 MWe PHWRs is also discussed. The experience regarding development testing of the proposed design of ion exchange column for 500 MWe PHWRs is also discussed

  16. The Value of the Operational Principle in Instructional Design

    Science.gov (United States)

    Gibbons, Andrew S.

    2009-01-01

    Formal design studies are increasing our insight into design processes, including those of instructional design. Lessons are being learned from other design fields, and new techniques and concepts can be imported as they are demonstrated effective. The purpose of this article is to introduce a design concept--the "operational principle"--for…

  17. Operation and Design of Diabatic Distillation Processes

    DEFF Research Database (Denmark)

    Bisgaard, Thomas

    Diabatic operation of a distillation column implies that heat is exchanged in one or more stages in the column. The most common way of realising diabatic operation is by internal heat integration resulting in a heat-integrated distillation column (HIDiC). When operating the rectifying section...... at a higher pressure, a driving forcefor transferring heat from the rectifying section to the stripping section is achieved. As a result, the condenser and reboiler duties can be significantly reduced. For two-product distillation, the HIDiC is a favourable alternative to the conventional distillation column....... Energy savings up to 83% are reported for the HIDiC compared to the CDiC, while the reported economical savings are as high as 40%. However, a simpler heat-integrated distillation column configuration exists, which employs compression in order to obtain a direct heat integration between the top vapour...

  18. LOFT instrumented fuel design and operating experience

    International Nuclear Information System (INIS)

    Russell, M.L.

    1979-01-01

    A summary description of the Loss-of-Fluid Test (LOFT) system instrumented core construction details and operating experience through reactor startup and loss-of-coolant experiment (LOCE) operations performed to date are discussed. The discussion includes details of the test instrumentation attachment to the fuel assembly, the structural response of the fuel modules to the forces generated by a double-ended break of a pressurized water reactor (PWR) coolant pipe at the inlet to the reactor vessel, the durability of the LOFT fuel and test instrumentation, and the plans for incorporation of improved fuel assembly test instrumentation features in the LOFT core

  19. Operational amplifier circuits analysis and design

    CERN Document Server

    Nelson, J C C

    1995-01-01

    This book, a revised and updated version of the author's Basic Operational Amplifiers (Butterworths 1986), enables the non-specialist to make effective use of readily available integrated circuit operational amplifiers for a range of applications, including instrumentation, signal generation and processing.It is assumed the reader has a background in the basic techniques of circuit analysis, particularly the use of j notation for reactive circuits, with a corresponding level of mathematical ability. The underlying theory is explained with sufficient but not excessive, detail. A range of compu

  20. KALIMER design database development and operation manual

    International Nuclear Information System (INIS)

    Jeong, Kwan Seong; Hahn, Do Hee; Lee, Yong Bum; Chang, Won Pyo

    2000-12-01

    KALIMER Design Database is developed to utilize the integration management for Liquid Metal Reactor Design Technology Development using Web Applications. KALIMER Design database consists of Results Database, Inter-Office Communication (IOC), 3D CAD database, Team Cooperation System, and Reserved Documents. Results Database is a research results database for mid-term and long-term nuclear R and D. IOC is a linkage control system inter sub project to share and integrate the research results for KALIMER. 3D CAD Database is a schematic design overview for KALIMER. Team Cooperation System is to inform team member of research cooperation and meetings. Finally, KALIMER Reserved Documents is developed to manage collected data and several documents since project accomplishment

  1. Consideration of dismantling operations in the design

    International Nuclear Information System (INIS)

    Dubourg; Bonin.

    1984-12-01

    This analysis shows that the parameters and the constraints taken into account at the design level to facilitate the exploitation and the maintenance make the dismantling and its preparation easier [fr

  2. KALIMER design database development and operation manual

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Kwan Seong; Hahn, Do Hee; Lee, Yong Bum; Chang, Won Pyo

    2000-12-01

    KALIMER Design Database is developed to utilize the integration management for Liquid Metal Reactor Design Technology Development using Web Applications. KALIMER Design database consists of Results Database, Inter-Office Communication (IOC), 3D CAD database, Team Cooperation System, and Reserved Documents. Results Database is a research results database for mid-term and long-term nuclear R and D. IOC is a linkage control system inter sub project to share and integrate the research results for KALIMER. 3D CAD Database is a schematic design overview for KALIMER. Team Cooperation System is to inform team member of research cooperation and meetings. Finally, KALIMER Reserved Documents is developed to manage collected data and several documents since project accomplishment.

  3. Work Zone Design and Operations Enhancements

    Science.gov (United States)

    2010-02-01

    Oregon Department of Transportation contractors are required to implement Traffic Control Plans (TCPs) to protect and direct traffic through work zones. The design and implementation of TCPs have shown variation from project-to-project across the Sta...

  4. Aggregation Operator Based Fuzzy Pattern Classifier Design

    DEFF Research Database (Denmark)

    Mönks, Uwe; Larsen, Henrik Legind; Lohweg, Volker

    2009-01-01

    This paper presents a novel modular fuzzy pattern classifier design framework for intelligent automation systems, developed on the base of the established Modified Fuzzy Pattern Classifier (MFPC) and allows designing novel classifier models which are hardware-efficiently implementable....... The performances of novel classifiers using substitutes of MFPC's geometric mean aggregator are benchmarked in the scope of an image processing application against the MFPC to reveal classification improvement potentials for obtaining higher classification rates....

  5. Instructor/Operator Station (IOS) Design Guide.

    Science.gov (United States)

    1988-02-01

    INSTRUTOR /OPERATOR STATION (IOS) AI O...The three functional categories also define three different users in terms of jobs and qualifications (if the functions have been allocated to manual ...function manually (e.g., collect the data S required from schedules, printed course outlines and telephone calls to training and facility managers).

  6. Operating system design the Xinu approach

    CERN Document Server

    Comer, Douglas

    2015-01-01

    The book guides readers through the construction of a conventional process-based operating system using practical, straightforward primitives. It gives the implementation details of one set of primitives, usually the most popular set. Once readers understand how primitives can be implemented on conventional hardware, they can then easily implement alternative versions.

  7. Methodology for Designing Operational Banking Risks Monitoring System

    Science.gov (United States)

    Kostjunina, T. N.

    2018-05-01

    The research looks at principles of designing an information system for monitoring operational banking risks. A proposed design methodology enables one to automate processes of collecting data on information security incidents in the banking network, serving as the basis for an integrated approach to the creation of an operational risk management system. The system can operate remotely ensuring tracking and forecasting of various operational events in the bank network. A structure of a content management system is described.

  8. Impact of LMFBR operating experience on PFBR design

    International Nuclear Information System (INIS)

    Bhoje, S.B.; Chetal, S.C.; Chellapandi, P.; Govindarajan, S.; Lee, S.M.; Kameswara Rao, A.S.L.; Prabhakar, R.; Raghupathy, S.; Sodhi, B.S.; Sundaramoorthy, T.R.; Vaidyanathan, G.

    2000-01-01

    PFBR is a 500 MWe, sodium cooled, pool type, fast breeder reactor currently under detailed design. It is essential to reduce the capital cost of PFBR in order to make it competitive with thermal reactors. Operating experience of LMFBRs provides a vital input towards simplification of the design, improving its reliability, enhancing safety and achieving overall cost reduction. This paper includes a summary of LMFBR operating experience and details the design features of PFBR as influenced by operating experience of LMFBRs. (author)

  9. Constructed wetlands for pollution control: processes, performance, design and operation

    National Research Council Canada - National Science Library

    2000-01-01

    .... Types of constructed wetland, major design parameters, role of vegetation, hydraulic patterns, loadings, treatment efficiency, construction, operation and maintenance costs are discussed in depth...

  10. Design of comprehensive general maintenance service system of aerial reconnaissance camera

    Directory of Open Access Journals (Sweden)

    Li Xu

    2016-01-01

    Full Text Available Aiming at the problem of lack of security equipment for airborne reconnaissance camera and universal difference between internal and external field and model, the design scheme of comprehensive universal system based on PC-104 bus architecture and ARM wireless test module is proposed is proposed using the ATE design. The scheme uses the "embedded" technology to design the system, which meets the requirements of the system. By using the technique of classified switching, the hardware resources are reasonably extended, and the general protection of the various types of aerial reconnaissance cameras is realized. Using the concept of “wireless test”, the test interface is extended to realize the comprehensive protection of the aerial reconnaissance camera and the field. The application proves that the security system works stably, has good generality, practicability, and has broad application prospect.

  11. Meter Designs Reduce Operation Costs for Industry

    Science.gov (United States)

    2013-01-01

    Marshall Space Flight Center collaborated with Quality Monitoring and Control (QMC) of Humble, Texas, through a Space Act Agreement to design a balanced flow meter for the Space Shuttle Program. QMC founded APlus-QMC LLC to commercialize the technology, which has contributed to 100 new jobs, approximately $250,000 in yearly sales, and saved customers an estimated $10 million.

  12. Design of motors for inverter operation

    Energy Technology Data Exchange (ETDEWEB)

    Haring, T. [ABB Motors OY, Vaasa (Finland)

    2000-07-01

    This paper describes very practical principles of how an induction motor should be designed for converter application. The main focus targets the efficiency of the motor and drive. The results presented are based on actual test motors and FEM-calculation simulations. FEM-calculation together with a time-stepping function is a powerful tool for estimating magnetic flux densities, iron losses, current densities and corresponding losses in windings, in other words a tool for optimisation of the motor design. Time-stepping is rather time consuming because all the circuit equations must be solved for each time-step, but it provides a way to estimate the iron losses; hysteresis and eddy current losses as well as current distribution and current losses. The calculation tool also provides the possibility to check if an existing motor is feasible for a converter drive. Alternatively if a motor is only to be supplied by a converter there are many more degrees of freedom in the electrical design and the motor may be optimised for that converter drive by incorporationg rather simple design changes. Additionally a design compromise, ''a general purpose motor'' useable for DOL and feasible for converter drive can be produced following the principles presented herewith. The converter types which are considered are indirect types and mainly voltage source converters since they are the most common on the market and are ''general purpose converters'' and providing a certain freedom to select the motor for the drive. Current source converters require ''matching'' with the motor and therefore need a precise knowledge of the motor equivalent circuit, making the selection of the motor more complicated. (orig.)

  13. Modeling and Simulation for Mission Operations Work System Design

    Science.gov (United States)

    Sierhuis, Maarten; Clancey, William J.; Seah, Chin; Trimble, Jay P.; Sims, Michael H.

    2003-01-01

    Work System analysis and design is complex and non-deterministic. In this paper we describe Brahms, a multiagent modeling and simulation environment for designing complex interactions in human-machine systems. Brahms was originally conceived as a business process design tool that simulates work practices, including social systems of work. We describe our modeling and simulation method for mission operations work systems design, based on a research case study in which we used Brahms to design mission operations for a proposed discovery mission to the Moon. We then describe the results of an actual method application project-the Brahms Mars Exploration Rover. Space mission operations are similar to operations of traditional organizations; we show that the application of Brahms for space mission operations design is relevant and transferable to other types of business processes in organizations.

  14. A Case Against Systematic Operational Design

    Science.gov (United States)

    2009-01-01

    timing, and logistics), and the enemy (relative skill, competence, and the will to fight). In contrast, Li strategy focused on the physical aspects of...Washington, DC, December 2008, available at <www.operationaldesign.com/RESTRICTED/ coursebook /ARCENT/ARCENT%20coursebook. html>. 3 Patrick E. McGlade... coursebook / ARCENT/01Event_15-19%20DEC%2008/ TAB%20I_Renewing%20the%20Core%20of%20 OperationalArt.pdf>. 24 Green, 24. 25 Ibid., 24; Wass de Czege, 4. 26

  15. Artificial intelligence in process design and operation

    International Nuclear Information System (INIS)

    Sudduth, A.L.

    1988-01-01

    Artificial Intelligence (AI) has recently become prominent in the discussion of computer applications in the utility business. In order to assess this technology, a research project was performed to determine whether software development techniques based on AI could be used to facilitate management of information associated with the design of a generating station. The approach taken was the development of an expert system, using a relatively simple set of rules acting on a more complex knowledge base. A successful prototype for the application was developed and its potential extension to a production environment demonstrated. During the course of prototype development, other possible applications of AI in design engineering were discovered, and areas of particular interest selected for further investigation. A plan for AI R and D was formulated. That plan and other possible future work in AI are discussed

  16. LOFT fuel design and operating experience

    International Nuclear Information System (INIS)

    Russell, M.L.

    1978-01-01

    The purpose of the LOFT fuel is to provide a pressurized water reactor core that has (1) test instrumentation for measurement of core conditions and (2) materials and geometric features to ensure heat transfer, hydraulic, mechanical, chemical, metallurgical and nuclear behaviors are typical of large pressurized water reactors (LPWRS) during the loss-of-coolant accident (LOCA) sequence. The LOFT core is unique because it is designed for exposure to several LOCAs without loss of function

  17. Small sodium valve design and operating experience

    International Nuclear Information System (INIS)

    Abramson, R.; Elie, X.; Vercasson, M.; Nedelec, J.

    1974-01-01

    Conventionally, valves for sodium pipes smaller than 125 mm in diameter are called ''small sodium valves''. However, this limit should rather be considered as the lower limit o ''large sodium valves''. In fact, both the largest sizes of small valves and the smallest of large valves can be found in the range of 125-300 mm in diameter. Thus what is said about small valves also applies, for a few valve types, above the 125 mm limit. Sodium valves are described here in a general manner, with no manufacturing details except when necessary for understanding valve behavior. Operating experience is pointed out wherever possible. Finally, some information is given about ongoing or proposed development plans. (U.S.)

  18. Design of a steganographic virtual operating system

    Science.gov (United States)

    Ashendorf, Elan; Craver, Scott

    2015-03-01

    A steganographic file system is a secure file system whose very existence on a disk is concealed. Customarily, these systems hide an encrypted volume within unused disk blocks, slack space, or atop conventional encrypted volumes. These file systems are far from undetectable, however: aside from their ciphertext footprint, they require a software or driver installation whose presence can attract attention and then targeted surveillance. We describe a new steganographic operating environment that requires no visible software installation, launching instead from a concealed bootstrap program that can be extracted and invoked with a chain of common Unix commands. Our system conceals its payload within innocuous files that typically contain high-entropy data, producing a footprint that is far less conspicuous than existing methods. The system uses a local web server to provide a file system, user interface and applications through a web architecture.

  19. HIFOGS: Its design, operations and calibration

    Science.gov (United States)

    Witteborn, Fred C.; Cohen, Martin; Bregman, Jesse D.; Heere, Karen R.; Greene, Thomas P.; Wooden, Diane H.

    The High-efficiency, Infrared Faint Object Grating Spectrometer (HIFOGS) provides spectral coverage of selectable portions of the 3 to 18 micron range at resolving powers from 00 to 1000 using 120 Si/Bi detectors. Additional coverage to 30 microns is provided by a bank of 32 Si:P detectors. Selectable apertures, gratings and band-pass filters provide flexibility to this system. Software for operation of HIFOGS and reduction of the data runs on a MacIntosh computer. HIFOGS has been used to establish celestial flux standards using 3 independent approaches: comparison to star models, comparisons to asteroid models and comparisons to laboratory blackbodies. These standards are expected to have wide application in astronomical thermal-infrared spectroscopy.

  20. Design and operation of the Sandia Pilot Plant

    International Nuclear Information System (INIS)

    Morris, M.E.

    1980-01-01

    An 8 ton/day dry sewage sludge irradiator was designed and constructed at Sandia National Laboratories in the last half of 1977 and in 1978; and was charged with 137 Cs and made operational in the spring of 1979. The design of the major subsystems of the irradiator is described. Subsequent operational experiences are also summarized

  1. Design of Air Traffic Control Operation System

    Directory of Open Access Journals (Sweden)

    Gabriela STROE

    2017-09-01

    Full Text Available This paper presents a numerical simulation for a different aircraft, based on the specific aircraft data that can be incorporated in the model and the equations of motions which can be consequently solved. The aircraft flight design involves various technical steps and requires the use of sophisticated software having modeling and simulation capabilities. Within the flight simulation model, the aerodynamic model can be regarded as the most complex and most important. With appropriate aerodynamic modeling the aerodynamic forces and moments acting on the aircraft's center of gravity can be numerically solved with accuracy. These forces and moments are further used to solve the equations of motion. The development of control and computing technology makes it possible for advanced flight control strategy. The advanced control techniques tend to make the control design and their implementation much more complicated with more control loops or channels; in this line, the autopilot of modern aircrafts includes a variety of automatic control systems that aid and support the flight navigation, flight management, and perform the enhancing and/or augmenting of the stability characteristics of the airplane. Therefore in this context it is very important to choose the dynamic that will satisfy the performance and robustness specifications.

  2. 40 CFR 264.273 - Design and operating requirements.

    Science.gov (United States)

    2010-07-01

    ... the facility permit how the owner or operator will design, construct, operate, and maintain the land..., construct, operate, and maintain the treatment zone to minimize run-off of hazardous constituents during the... maintain a run-on control system capable of preventing flow onto the treatment zone during peak discharge...

  3. Evaluating hospital design from an operations management perspective.

    Science.gov (United States)

    Vos, Leti; Groothuis, Siebren; van Merode, Godefridus G

    2007-12-01

    This paper describes an evaluation method for the assessment of hospital building design from the viewpoint of operations management to assure that the building design supports the efficient and effective operating of care processes now and in the future. The different steps of the method are illustrated by a case study. In the case study an experimental design is applied to assess the effect of used logistical concepts, patient mix and technologies. The study shows that the evaluation method provides a valuable tool for the assessment of both functionality and the ability to meet future developments in operational control of a building design.

  4. Designing visual displays and system models for safe reactor operations

    Energy Technology Data Exchange (ETDEWEB)

    Brown-VanHoozer, S.A.

    1995-12-31

    The material presented in this paper is based on two studies involving the design of visual displays and the user`s prospective model of a system. The studies involve a methodology known as Neuro-Linguistic Programming and its use in expanding design choices from the operator`s perspective image. The contents of this paper focuses on the studies and how they are applicable to the safety of operating reactors.

  5. Engineering Design and Operation Report: Biological ...

    Science.gov (United States)

    Many regions in the United States have excessive levels of ammonia in their drinking water sources (e.g., ground and surface waters) as a result of naturally occurring processes, agricultural and urban runoff, concentrated animal feeding operations, municipal wastewater treatment plants, and other sources. Ammonia is not regulated by the U.S. Environmental Protection Agency (EPA) as a contaminant. Based on a 2003 World Health Organization (WHO) assessment, ammonia levels in groundwater are typically below 0.2 milligrams per liter (mg/L), and do not pose a direct health concern at levels expected in drinking water (WHO 2003); however, they may pose a concern when nitrification of significant levels of ammonia from the source water occurs in the drinking water distribution system. Specifically, this nitrification, which is the conversion of the ammonia to nitrite and nitrate by bacteria, leads to water quality issues, such as potential corrosion problems, oxidant demand, taste and odor complaints, and elevated nitrite levels (Bremer et al.,2001; Fleming et al., 2005; Lee et al., 1980; Odell et al., 1996; Rittman & Snoeyink, 1984; Suffet et al., 1996). The EPA’s regulatory limits for nitrite and nitrate (at the entry point to the distribution system) are 0.1 and 10 mg N/L, respectively. Ammonia in water may also pose problems with water treatment effectiveness. For example, in source waters containing both ammonia and arsenic, the ammonia may negatively impact

  6. Snow model design for operational purposes

    Science.gov (United States)

    Kolberg, Sjur

    2017-04-01

    A parsimonious distributed energy balance snow model intended for operational use is evaluated using discharge, snow covered area and grain size; the latter two as observed from the MODIS sensor. The snow model is an improvement of the existing GamSnow model, which is a part of the Enki modelling framework. Core requirements for the new version have been: 1. Reduction of calibration freedom, motivated by previous experience of non-identifiable parameters in the existing version 2. Improvement of process representation based on recent advances in physically based snow modelling 3. Limiting the sensitivity to forcing data which are poorly known over the spatial domain of interest (often in mountainous areas) 4. Preference for observable states, and the ability to improve from updates. The albedo calculation is completely revised, now based on grain size through an emulation of the SNICAR model (Flanner and Zender, 2006; Gardener and Sharp, 2010). The number of calibration parameters in the albedo model is reduced from 6 to 2. The wind function governing turbulent energy fluxes has been reduced from 2 to 1 parameter. Following Raleigh et al (2011), snow surface radiant temperature is split from the top layer thermodynamic temperature, using bias-corrected wet-bulb temperature to model the former. Analyses are ongoing, and the poster will bring evaluation results from 16 years of MODIS observations and more than 25 catchments in southern Norway.

  7. Influence of probabilistic safety analysis on design and operation of PWR plants

    International Nuclear Information System (INIS)

    Bastl, W.; Hoertner, H.; Kafka, P.

    1978-01-01

    This paper gives a comprehensive presentation of the connections and influences of probabilistic safety analysis on design and operation of PWR plants. In this context a short historical retrospective view concerning probabilistic reliability analysis is given. In the main part of this paper some examples are presented in detail, showing special outcomes of such probabilistic investigations. Additional paragraphs illustrate some activities and issues in the field of probabilistic safety analysis

  8. The investigation of the design of hybrid operating room

    International Nuclear Information System (INIS)

    Jiang Weihao; Li Jun

    2011-01-01

    Objective: To investigate the design of the interventional operating room that can meet the needs of modern DSA operation, and the overall arrangement of the hybrid operating room should be reasonable, practical and perspective. Methods: The experience and understanding obtained from the designing and planning of the new Building of Radiology and Surgery in authors' hospital were summarized. In order to meet the requirements of aseptic surgical practices and a full-featured hybrid operating room the following factors should be carefully and synthetically taken into account: the room size, the functional sub-areas, the operational procedures, the aseptic specification, etc. Results: The sufficient verification and scientific design were the important link for building a hybrid operating room. It could provide the surgeons and interventional physicians with more alternative operating methods and it could represent the development trend of medical technology. Conclusion: When planning and designing a new DSA operating room, various factors related to the interventional procedures, such as the room size, the functional sub-areas, the operational procedures and the aseptic specification, should be carefully and synthetically taken into account. The standard of aseptic procedure must be strictly complied with and the various functional sub-areas need to be rationally distributed. The design of hybrid operating room, which joins the functions of both open surgery and interventional management together, should be scientific, practical and perspective. (authors)

  9. The enhancement of Ignalina NPP in design and operational safety

    International Nuclear Information System (INIS)

    Negrivoda, G.

    1999-01-01

    Enhancement of Ignalina NPP design include: core design improvements; fuel channel integrity (multiple pressure tube rupture); improvements of shutdown systems; improvements of instrumentation and control devices; containment strength and tightness; design basis accident analysis; improvements of safety and support systems; seismic safety enhancement; Year 2000 project; cracks in pipes. Enhancement of operational safety includes: quality assurance; configuration management; safety management and safety culture; emergency operating procedures; training and full scope simulator; in-service inspection; fire protection and ageing monitoring and management

  10. The State of Design : A Comprehensive Literature Review to Chart the Design Science Research Discourse

    NARCIS (Netherlands)

    Thakurta, Rahul; Mueller, Benjamin; Ahlemann, Frederik; Hoffman, David

    Design science is an increasingly popular research paradigm in the information systems discipline. De- spite a recognition of the design science research par- adigm, questions are being raised about the nature of its existence and its contributions. Central to this ar- gument is the understanding of

  11. Operating system design the Xinu approach, Linksys version

    CERN Document Server

    Press, CRC

    2011-01-01

    Introduction and OverviewOperating SystemsApproach Used In The TextA Hierarchical DesignThe Xinu Operating SystemWhat An Operating System Is NotAn Operating System Viewed From The OutsideRemainder Of The TextConcurrent Execution And Operating System ServicesProgramming Models For Multiple ActivitiesOperating System ServicesConcurrent Processing Concepts And TerminologyDistinction Between Sequential And Concurrent ProgramsMultiple Processes Sharing A Single Piece Of CodeProcess Exit And Process TerminationShared Memory, Race Conditions, And SynchronizationSemaphores And Mutual ExclusionType Nam

  12. Assessment of Offshore Wind System Design, Safety, and Operation Standards

    Energy Technology Data Exchange (ETDEWEB)

    Sirnivas, Senu [National Renewable Energy Lab. (NREL), Golden, CO (United States); Musial, Walt [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bailey, Bruce [AWS Trupower LLC, Albany, NY (United States); Filippelli, Matthew [AWS Trupower LLC, Albany, NY (United States)

    2014-01-01

    This report is a deliverable for a project sponsored by the U.S. Department of Energy (DOE) entitled National Offshore Wind Energy Resource and Design Data Campaign -- Analysis and Collaboration (contract number DE-EE0005372; prime contractor -- AWS Truepower). The project objective is to supplement, facilitate, and enhance ongoing multiagency efforts to develop an integrated national offshore wind energy data network. The results of this initiative are intended to 1) produce a comprehensive definition of relevant met-ocean resource assets and needs and design standards, and 2) provide a basis for recommendations for meeting offshore wind energy industry data and design certification requirements.

  13. CVISN operational and architectural compatibility handbook (COACH). Part 1, Operational concept and top-level design checklists

    Science.gov (United States)

    1999-04-22

    The CVISN Operational and Architectural Compatibility Handbook (COACH) provides a comprehensive checklist of what is required to conform with the Commercial Vehicle Information Systems and Networks (CVISN) operational concepts and architecture. It is...

  14. Incorporating operational experience and design changes in availability forecasts

    International Nuclear Information System (INIS)

    Norman, D.

    1988-01-01

    Reliability or availability forecasts which are based solely on past operating experience will be precise if the sample is large enough, and unbiased if nothing in the future design, environment, operating region or anything else changes. Unfortunately, life is never like that. This paper considers the methodology and philosophy of modifying forecasts based on past experience to take account also of changes in design, construction methods, operating philosophy, environments, operator training and so on, between the plants which provided the operating experience and the plant for which the forecast is being made. This emphasises the importance of collecting, assessing, and learning from past data and of a thorough knowledge of future designs, and procurement, operation, and maintenance policies. The difference between targets and central estimates is also discussed. The paper concludes that improvements in future availability can be made by learning from past experience, but that certain conditions must be fulfilled in order to do so. (author)

  15. Comprehension with Instructional Media for Middle School Science: Holistic Performative Design Strategy and Cognitive Load

    Science.gov (United States)

    Peterson, Matthew Owen

    This study identifies three distinct levels of text-image integration in page design in a linear relationship of lesser to greater integration: prose primary, prose subsumed, and fully integrated strategies. Science textbook pages were redesigned according to these holistic design strategies for 158 7th-grade students. There were three separate treatment tests, as well as a pre-test and post-test, and pilot tests with both undergraduate students and the subjects themselves. Subjects found the fully integrated strategy to produce the most visually interesting designs and the prose primary strategy to produce the least interesting, with prose subsumed definitively in between (according to 95% confidence intervals). The strategy employed significantly altered interest in science subject matter in one of three treatments (ANOVA, P=0.0446), where a Student's t-test revealed that the prose subsumed strategy produced higher interest in subject matter than prose primary. The strategy employed significantly altered comprehension of abstract relationships in one of three treatments (ANOVA, P=0.0202), where a Student's t-test revealed that the fully integrated strategy resulted in greater comprehension than prose primary. For the same treatment condition significant differences were found through ANOVA for factual-level knowledge (P=0.0289) but not conceptual-level knowledge ( P=0.0586). For factual-level knowledge prose primary resulted in lesser comprehension than both prose subsumed and fully integrated. Comprehension is defined according to cognitive load theory. No strategy impact on perception of task difficulty was found. This study was approved by North Carolina State University's Institutional Review Board and Wake County Public School System's Research Review Committee.

  16. Design parameters and operating characteristics of animal waste anaerobic digestion systems - swine and poultry

    Energy Technology Data Exchange (ETDEWEB)

    Hill, D T

    1983-01-01

    The development and validation of a comprehensive dynamic simulation model of the anaerobic fermentation of animal waste have been described by Hill. This model has proved to be highly accurate, both qualitatively and quantitatively, in predicting the steady-state methane productivity of conventional fermentation plants and in simulating the transient-state response of semi-batch fed digesters. Simulation studies using this model have been performed and results have been used to develop design recommendations for steady-state operations. These simulation studies have also produced a start-up procedure that will ensure successful initial operation of the digestion system and, more importantly, have allowed determination of the operational techniques that will provide recovery from failure due to organic overloading or excessively short detention time. This paper describes the results of these studies for swine and poultry (caged layer) waste and presents the design recommendations and operating techniques developed from the simulations. (Refs. 11).

  17. The development of an ergonomics standard for the design of operator interfaces

    International Nuclear Information System (INIS)

    Kirwan, B.; Reed, J.; Litherland, M.

    1990-01-01

    BNFL has realised the need to take a consistent approach to the ergonomic design of operator interfaces. Towards this aim, a design standard document has been produced under the direction of a principal design engineer based on the key ergonomics aspects of plant design. The standard was requested by the designers, and the original standard was produced by ergonomists working on BNFL projects. This standard was then reviewed by a large number of key design and operations personnel, and a series of multidisciplinary meetings produced the final version. The standard contains six sections (ergonomics requirements for the design of Control Rooms, Consoles and Panels Design, Labelling, VDU Systems, Alarm Systems and Colour Coding) containing approximately 180 guidelines in text format or supplemented by diagrams and tables. Each guideline is classified as either mandatory or advisory. A high proportion of effort concentrated on making the document usable by designers. The standard is not intended to be fully comprehensive, since the range of possible variations in the designs of interfaces makes such a task intractable at this stage. However, the document does ensure that account is taken of ergonomics throughout the design phase, and particularly in the early phases whilst design change is still cost-effective, and that designers are aware of the important issues and principles. (author)

  18. Operator model-based design and evaluation of advanced systems

    International Nuclear Information System (INIS)

    Schryver, J.C.

    1988-01-01

    A multi-level operator modeling approach is recommended to provide broad support for the integrated design of advanced control and protection systems for new nuclear power plants. Preliminary design should address the symbiosis of automated systems and human operator by giving careful attention to the roles assigned to these two system elements. A conceptual model of the operator role is developed in the context of a command control-communication problem. According to this approach, joint responsibility can be realized in at least two ways: sharing or allocation. The inherent stabilities of different regions of the operator role space are considered

  19. Advances in new WWER designs to improve operation and maintenance

    International Nuclear Information System (INIS)

    Dragunov, Y.G.; Ryzhov, S.B.; Podshibiakin, A.K.; Vasilchenko, I.N.; Repin, A.I.; Nikitenko, M.P.; Konoplev, N.P.; Fil, N.S.

    2000-01-01

    Economic operational indices of WWER-type reactors show their competitiveness in all the countries where these reactors operate. Advanced WWERs being designed and constructed now have the improved characteristics of economical efficiency and are more convenient for operation and maintenance. Many technical solutions aimed at improvement of the operational performance are implemented in the design of WWER-1000/V-392 and WWER-640/V-407, and these reactors are the important basis for the nuclear power expansion in Russia. Some of these solutions are considered in the present paper. (author)

  20. Innovative product design based on comprehensive customer requirements of different cognitive levels.

    Science.gov (United States)

    Li, Xiaolong; Zhao, Wu; Zheng, Yake; Wang, Rui; Wang, Chen

    2014-01-01

    To improve customer satisfaction in innovative product design, a topology structure of customer requirements is established and an innovative product approach is proposed. The topology structure provides designers with reasonable guidance to capture the customer requirements comprehensively. With the aid of analytic hierarchy process (AHP), the importance of the customer requirements is evaluated. Quality function deployment (QFD) is used to translate customer requirements into product and process design demands and pick out the technical requirements which need urgent improvement. In this way, the product is developed in a more targeted way to satisfy the customers. the theory of innovative problems solving (TRIZ) is used to help designers to produce innovative solutions. Finally, a case study of automobile steering system is used to illustrate the application of the proposed approach.

  1. Innovative Product Design Based on Comprehensive Customer Requirements of Different Cognitive Levels

    Directory of Open Access Journals (Sweden)

    Xiaolong Li

    2014-01-01

    Full Text Available To improve customer satisfaction in innovative product design, a topology structure of customer requirements is established and an innovative product approach is proposed. The topology structure provides designers with reasonable guidance to capture the customer requirements comprehensively. With the aid of analytic hierarchy process (AHP, the importance of the customer requirements is evaluated. Quality function deployment (QFD is used to translate customer requirements into product and process design demands and pick out the technical requirements which need urgent improvement. In this way, the product is developed in a more targeted way to satisfy the customers. the theory of innovative problems solving (TRIZ is used to help designers to produce innovative solutions. Finally, a case study of automobile steering system is used to illustrate the application of the proposed approach.

  2. Increasing Student Interest and Comprehension of Production Planning and Control and Operations Performance Measurement Concepts Using a Production Line Game

    Science.gov (United States)

    Cox, James F., III; Walker, Edward D., II

    2005-01-01

    Production planning and control (PPC) systems and operations performance measures are topics that students generally find both boring and difficult to understand. In the article, the authors present a production line game that they have found to be an effective tool to increase student interest in the topics as well as student comprehension. The…

  3. [Comprehensive care program for the mentally ill in Spanish prisons (PAIEM): assessment after four years operation].

    Science.gov (United States)

    Sanz, J; Gómez-Pintado, P; Ruiz, A; Pozuelo, F; Arroyo, J M

    2014-01-01

    To assess the comprehensive care program for the mentally ill in prison (PAIEM), which has been implemented for 3 years in Spanish prisons with the aim of improving processes and results. Descriptive study of the data gathered from an anonymous questionnaire completed by members of the PAIEM team in prisons. Frequency distributions were obtained of all the variables relating to facts, attitudes, opinions, experiences, situations and processes of the PAIEM. 91.2% of the PAIEM teams responded. Psychologists, educators, doctors and social workers were the professionals that collaborated most actively in the PAIEM (73%-84%) and were the ones to act most frequently as tutors. The mentally ill are usually located in ordinary modules (80%). The most commonly used activities for their psycho-social rehabilitation are self care (73%), education for health, preparation for daily life and social skills (more than 60%). Interventions with families are basically by telephone (79%). Bivariate analysis showed that the PAIEMs that operate most effectively are those that coordinate well with other technical teams, that prepare referral more than six months prior to release and ones where the NGOs process the referrals. Over 71% of the professionals observed improvements of disabilities and needs in over half the patients more than half of the professionals involved are satisfied (3.4/5) with their participation, although they acknowledge that there is a greater work load. The activities of the PAIEM are adequate, especially in the phases of early detection, stabilisation and rehabilitation and less so in the social incorporation phase, which improves when the third sector intervenes in referrals of patients to the social health care network outside prison.

  4. Designing nuclear power plants for improved operation and maintenance

    International Nuclear Information System (INIS)

    1996-09-01

    The purpose of this publication is to compile demonstrated, experience based design guidelines for improving the operability and maintainability of nuclear power plants. The guidelines are for use principally in the design of new nuclear power plants, but should also be useful in upgrading existing designs. The guidelines derive from the experience of operating and maintaining existing nuclear power plants as well as from the design of recent plants. In particular these guidelines are based on and consistent with both the EPRI advanced Light Water Reactor Utility Requirements Document, Volume 1, and the European Utility Requirements for LWR Nuclear Power Plants. 6 refs, 1 fig

  5. Designing nuclear power plants for improved operation and maintenance

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-09-01

    The purpose of this publication is to compile demonstrated, experience based design guidelines for improving the operability and maintainability of nuclear power plants. The guidelines are for use principally in the design of new nuclear power plants, but should also be useful in upgrading existing designs. The guidelines derive from the experience of operating and maintaining existing nuclear power plants as well as from the design of recent plants. In particular these guidelines are based on and consistent with both the EPRI advanced Light Water Reactor Utility Requirements Document, Volume 1, and the European Utility Requirements for LWR Nuclear Power Plants. 6 refs, 1 fig.

  6. Design and operating experiences with 50MW steam generator

    International Nuclear Information System (INIS)

    Kawara, M.; Yamaki, H.; Kanamori, A.; Tanaka, K.; Takahashi, T.

    1975-01-01

    The main purpose of the 50 MW steam generator is to have experiences of manufacturing and operation with large scale steam generator including necessary research and development works which can be reflected on the design and fabrication of 'Monju' (Japan 300 MWe prototype LMFBR). The detailed design of the 50 MW steam, generator was begun on March, 1972 and succeeded in the demonstration of 72 hours continuous operation with full power on June, 1974. It has been successfully operated since then, the performances of which have been evaluated through various kinds of tests. In this paper, the following items are mainly discussed system design, thermal and hydraulic design, structure and fabrication and some experiences on testing operation including cleaning and sodium flushing of equipment, sodium level control system, the behavior of hydrogen detection system and general outlook of the performance. (author)

  7. Reactor helium system, design specification, operation and handling

    International Nuclear Information System (INIS)

    Badrljica, R.

    1984-06-01

    Apart from detailed design specification of the helium cover gas system of the Ra reactor, this document includes description of the operating regime, instructions for manipulations in the system with the aim of achieving and maintaining stationary gas circulation [sr

  8. Design and operating experiences with 50MW steam generator

    Energy Technology Data Exchange (ETDEWEB)

    Kawara, M; Yamaki, H; Kanamori, A; Tanaka, K; Takahashi, T

    1975-07-01

    The main purpose of the 50 MW steam generator is to have experiences of manufacturing and operation with large scale steam generator including necessary research and development works which can be reflected on the design and fabrication of 'Monju' (Japan 300 MWe prototype LMFBR). The detailed design of the 50 MW steam, generator was begun on March, 1972 and succeeded in the demonstration of 72 hours continuous operation with full power on June, 1974. It has been successfully operated since then, the performances of which have been evaluated through various kinds of tests. In this paper, the following items are mainly discussed system design, thermal and hydraulic design, structure and fabrication and some experiences on testing operation including cleaning and sodium flushing of equipment, sodium level control system, the behavior of hydrogen detection system and general outlook of the performance. (author)

  9. Designing visual displays and system models for safe reactor operations

    International Nuclear Information System (INIS)

    Brown-VanHoozer, S.A.

    1995-01-01

    The material presented in this paper is based on two studies involving the design of visual displays and the user's prospective model of a system. The studies involve a methodology known as Neuro-Linguistic Programming and its use in expanding design choices from the operator's perspective image. The contents of this paper focuses on the studies and how they are applicable to the safety of operating reactors

  10. Design and operating condition. Consequences for EDF NPP's chemistry

    International Nuclear Information System (INIS)

    Bretelle, Jean-Luc; Stutzmann, Agnes; Nordmann, Francis

    2009-01-01

    Since the beginning of the French nuclear programme in 1977, four major types of design have been commissioned, the fifth one being under construction (EPR). The paper points out advantages and drawbacks of chemistry choices for the primary, secondary and tertiary systems in French NPP, for each design particularity and it describes the corresponding operating conditions. Chemistry option proposals are drawn for the future of the French fleet, taking into account the material behaviour and the operation improvement. (orig.)

  11. The electron test accelerator safety in design and operation

    International Nuclear Information System (INIS)

    McKeown, J.

    1980-06-01

    The Electron Test Accelerator is being designed as an experiment in accelerator physics and technology. With an electron beam power of up to 200 kW the operation of the accelerator presents a severe radiation hazard as well as rf and electrical hazards. The design of the safety system provides fail-safe protection while permitting flexibility in the mode of operation and minimizing administrative controls. (auth)

  12. The Design of a Capability-Based Distributed Operating System

    NARCIS (Netherlands)

    Mullender, Sape J.; Tanenbaum, A.S.

    Fifth-generation computer systems will use large numbers of processors to achieve high performance. In this paper a capability-based operating system designed for this environment is discussed. Capability-based operating systems have traditionally required large, complex kernels to manage the use of

  13. The Alternative Design Features for Safety Enhancement in Shutdown Operation

    International Nuclear Information System (INIS)

    Oh, Hae Cheol; Kim, Myung Ki; Chung, Bag Soon; Seo, Mi Ro

    2009-01-01

    PSA can be used to confirm that the new plant design is complied with the applicable safety goals, and to select among the alternate design options. A shutdown PSA provides insight for outage planning schedule, outage management practices, and design modifications. Considering the results of both LPSD PSA studies and operating experiences for low power and shutdown, the improvements can be proposed to reduce the high risk contribution. The improvements/enhancements during shutdown operation may be divided into categories such as hardware, administrative management, and operational procedure. This paper presents on an example how the risk related to an accidental situation can be reduced, focusing the hardware design changes for the newly designed NPPs

  14. Solid Waste Operations Complex W-113, Detail Design Report (Title II). Volume 1: Title II design report

    International Nuclear Information System (INIS)

    1995-09-01

    The Solid Waste Retrieval Facility--Phase 1 (Project W113) will provide the infrastructure and the facility required to retrieve from Trench 04, Burial ground 4C, contact handled (CH) drums and boxes at a rate that supports all retrieved TRU waste batching, treatment, storage, and disposal plans. This includes (1) operations related equipment and facilities, viz., a weather enclosure for the trench, retrieval equipment, weighing, venting, obtaining gas samples, overpacking, NDE, NDA, shipment of waste and (2) operations support related facilities, viz., a general office building, a retrieval staff change facility, and infrastructure upgrades such as supply and routing of water, sewer, electrical power, fire protection, roads, and telecommunication. Title I design for the operations related equipment and facilities was performed by Raytheon/BNFL, and that for the operations support related facilities including infrastructure upgrade was performed by KEH. These two scopes were combined into an integrated W113 Title II scope that was performed by Raytheon/BNFL. Volume 1 provides a comprehensive narrative description of the proposed facility and systems, the basis for each of the systems design, and the engineering assessments that were performed to support the technical basis of the Title II design. The intent of the system description presented is to provide WHC an understanding of the facilities and equipment provided and the A/E's perspective on how these systems will operate

  15. Design-for-variety, postponement, and operational performance

    DEFF Research Database (Denmark)

    Boer, Henrike Engele Elisabeth

    2015-01-01

    Design for variety (DFV) practices such as product modularization, platform thinking and design for manufacturing/assembly have been suggested to yield considerable operational performance benefits. Some of these performance effects can be expected in all manufacturing settings, including the pos...

  16. Design, construction and operation features of high-rise structures

    Science.gov (United States)

    Mylnik, Alexey; Mylnik, Vladimir; Zubeeva, Elena; Mukhamedzhanova, Olga

    2018-03-01

    The article considers design, construction and operation features of high-rise facilities. The analysis of various situations, that come from improper designing, construction and operation of unique facilities, is carried out. The integrated approach is suggested, when the problems of choosing acceptable constructional solutions related to the functional purpose, architectural solutions, methods of manufacturing and installation, operating conditions for unique buildings and structures are being tackled. A number of main causes for the emergency destruction of objects under construction and operation is considered. A number of measures are proposed on the basis of factor classification in order to efficiently prevent the situations, when various negative options of design loads and emergency impacts occur.

  17. Cryogenic propellant management: Integration of design, performance and operational requirements

    Science.gov (United States)

    Worlund, A. L.; Jamieson, J. R., Jr.; Cole, T. W.; Lak, T. I.

    1985-01-01

    The integration of the design features of the Shuttle elements into a cryogenic propellant management system is described. The implementation and verification of the design/operational changes resulting from design deficiencies and/or element incompatibilities encountered subsequent to the critical design reviews are emphasized. Major topics include: subsystem designs to provide liquid oxygen (LO2) tank pressure stabilization, LO2 facility vent for ice prevention, liquid hydrogen (LH2) feedline high point bleed, pogo suppression on the Space Shuttle Main Engine (SSME), LO2 low level cutoff, Orbiter/engine propellant dump, and LO2 main feedline helium injection for geyser prevention.

  18. High Altitude Venus Operations Concept Trajectory Design, Modeling and Simulation

    Science.gov (United States)

    Lugo, Rafael A.; Ozoroski, Thomas A.; Van Norman, John W.; Arney, Dale C.; Dec, John A.; Jones, Christopher A.; Zumwalt, Carlie H.

    2015-01-01

    A trajectory design and analysis that describes aerocapture, entry, descent, and inflation of manned and unmanned High Altitude Venus Operation Concept (HAVOC) lighter-than-air missions is presented. Mission motivation, concept of operations, and notional entry vehicle designs are presented. The initial trajectory design space is analyzed and discussed before investigating specific trajectories that are deemed representative of a feasible Venus mission. Under the project assumptions, while the high-mass crewed mission will require further research into aerodynamic decelerator technology, it was determined that the unmanned robotic mission is feasible using current technology.

  19. Multicriteria analysis of product operational effectiveness at design stages

    Science.gov (United States)

    Irzaev, G. Kh

    2018-03-01

    The multicriteria rapid assessment method of techno-economic parameters of new products is developed. It avoids expensive engineering changes during the operational stages through the analysis of external and internal factors at an early stage in the design that affect the maintainability and manufacturability of the product. The expert selection of the initial multitude of indicators from the five enlarged criteria groups and their subsequent pairwise comparison allow one to distinguish the complex compliance criteria of product design with the average and optimum values of the operational effectiveness. The values comparison provides an opportunity to decide on the continuation of the process for designing and preparation of the product manufacture.

  20. Supplemental design requirements document solid waste operations complex

    International Nuclear Information System (INIS)

    Ocampo, V.P.; Boothe, G.F.; Broz, D.R.; Eaton, H.E.; Greager, T.M.; Huckfeldt, R.A.; Kooiker, S.L.; Lamberd, D.L.; Lang, L.L.; Myers, J.B.

    1994-11-01

    This document provides additional and supplemental information to the WHC-SD-W112-FDC-001, WHC-SD-W113-FDC-001, and WHC-SD-W100-FDC-001. It provides additional requirements for the design and summarizes Westinghouse Hanford Company key design guidance and establishes the technical baseline agreements to be used for definitive design common to the Solid Waste Operations Complex (SWOC) Facilities (Project W-112, Project W-113, and WRAP 2A)

  1. Design of CMOS CFOA Based on Pseudo Operational Transconductance Amplifier

    OpenAIRE

    Hassan Jassim Motlak

    2015-01-01

    A novel design technique employing CMOS Current Feedback Operational Amplifier (CFOA) is presented. The feature of consumption very low power in designing pseudo-OTA is used to decreasing the total power consumption of the proposed CFOA. This design approach applies pseudo-OTA as input stage cascaded with buffer stage. Moreover, the DC input offset voltage and harmonic distortion (HD) of the proposed CFOA are very low values compared with the conventional CMOS CFOA due to...

  2. From “Comprehensive Transportation Hub” to “City New Sitting Room”---Overall the design about Jinan East district comprehensive transportation hub

    Science.gov (United States)

    Lv, Jie; Guo, Jianmin; Li, Jin

    2017-08-01

    integrated transport hub or high-speed rail station often talked about, often known as the “city portal” and the title of “city window”, so the comprehensive transportation hub or the high-speed rail station of a city is very important to a region or a provincial. At the same time, it reflects that the managers and users of a city only focus on the comprehensive transportation hub of transportation service function and ignore her cities attributes and functions. Jinan east district comprehensive transportation hub in the beginning of design is given a feature that it has to serve both the traffic and city. We are trying to build a new center for Jinan east new town, the window to welcome people, the city hall of hospitality.

  3. Implications of steady-state operation on divertor design

    International Nuclear Information System (INIS)

    Sevier, D.L.; Reis, E.E.; Baxi, C.B.; Silke, G.W.; Wong, C.P.C.; Hill, D.N.

    1996-01-01

    As fusion experiments progress towards long pulse or steady state operation, plasma facing components are undergoing a significant change in their design. This change represents the transition from inertially cooled pulsed systems to steady state designs of significant power handling capacity. A limited number of Plasma Facing Component (PFC) systems are in operation or planning to address this steady state challenge at low heat flux. However in most divertor designs components are required to operate at heat fluxes at 5 MW/m 2 or above. The need for data in this area has resulted in a significant amount of thermal/hydraulic and thermal fatigue testing being done on prototypical elements. Short pulse design solutions are not adequate for longer pulse experiments and the areas of thermal design, structural design, material selection, maintainability, and lifetime prediction are undergoing significant changes. A prudent engineering approach will guide us through the transitional phase of divertor design to steady-state power plant components. This paper reviews the design implications in this transition to steady state machines and the status of the community efforts to meet evolving design requirements. 54 refs., 5 figs., 2 tabs

  4. Zebrafish housing systems: a review of basic operating principles and considerations for design and functionality.

    Science.gov (United States)

    Lawrence, Christian; Mason, Timothy

    2012-01-01

    The strategies for housing zebrafish used in biomedical research have evolved considerably over the past three decades. To keep pace with the rapid expansion and development of the zebrafish model system, the field has generally moved from keeping fish at the level of aquarium hobbyist to that of industrialized, recirculating aquaculture. Numerous commercial system vendors now offer increasingly sophisticated housing systems based on design principles that maximize the number of animals that can be housed in a given space footprint, and they are thus able to support large and diverse research programs. This review is designed to provide managers, lab animal veterinarians, investigators, and other parties responsible for care and use of these animals with a comprehensive overview of the basic operating and design principles of zebrafish housing systems. This information can be used to help plan the construction of new facilities and/or the upgrade and maintenance of existing operations.

  5. Principles of Design And Operations Of Wastewater Treatment Pond Systems For Plant Operators, Engineers, And Managers

    Science.gov (United States)

    Wastewater pond systems provide reliable, low cost, and relatively low maintenance treatment for municipal and industrial discharges. However, they do have certain design, operations, and maintenance requirements. While the basic models have not changed in the 30-odd years sinc...

  6. Liquid metal cooled reactors: Experience in design and operation

    International Nuclear Information System (INIS)

    2007-12-01

    on key fast reactor technology aspects in an integrative sense useful to engineers, scientists, managers, university students and professors. This publication has been prepared to contribute toward the IAEA activity to preserve the knowledge gained in the liquid metal cooled fast reactor (LMFR) technology development. This technology development and experience include aspects addressing not only experimental and demonstration reactors, but also all activities from reactor construction to decommissioning. This publication provides a survey of worldwide experience gained over the past five decades in LMFR development, design, operation and decommissioning, which has been accumulated through the IAEA programmes carried out within the framework of the TWG-FR and the Agency's INIS and NKMS

  7. System 80+TM standard plant: Design and operations overview

    International Nuclear Information System (INIS)

    Matzie, R.A.; Ritterbusch, S.E.

    1999-01-01

    The System 80+ Standard Plant Design is a 1400 MWe evolutionary Advanced Light Water Reactor (ALWR), designed to meet the Electric Power Research Institute (EPRI) ALWR Utility Requirements Document (URD) and the demands of the international market for nuclear power plants which are not only safer but also more economical to maintain and operate. ABB Combustion Engineering Nuclear Power used a defense-in-depth process that (1) adds design margin to basic components to improve performance during normal operation and to decrease the likelihood of an unanticipated transient or an accident, (2) improves the redundancy and diversity of safety systems in order to mitigate design basis accidents and prevent severe accidents, and (3) improves severe accident mitigation capability. This paper describes the most important improved systems and components with emphasis on severe accident prevention and mitigation capability. The improved design features were implemented in an evolutionary manner using proven components. This approach ensures that the plant operates safely and economically, as demonstrated by operating plants in the US and the Republic of Korea. Detailed studies, summarized in this paper, have shown that the System 80+ plant availability is expected to exceed the ALWR requirement of 87% and that the annual operations and maintenance costs are expected to be reduced by $14 million. (author)

  8. Low-voltage CMOS operational amplifiers theory, design and implementation

    CERN Document Server

    Sakurai, Satoshi

    1995-01-01

    Low-Voltage CMOS Operational Amplifiers: Theory, Design and Implementation discusses both single and two-stage architectures. Opamps with constant-gm input stage are designed and their excellent performance over the rail-to-rail input common mode range is demonstrated. The first set of CMOS constant-gm input stages was introduced by a group from Technische Universiteit, Delft and Universiteit Twente, the Netherlands. These earlier versions of circuits are discussed, along with new circuits developed at the Ohio State University. The design, fabrication (MOSIS Tiny Chips), and characterization of the new circuits are now complete. Basic analog integrated circuit design concepts should be understood in order to fully appreciate the work presented. However, the topics are presented in a logical order and the circuits are explained in great detail, so that Low-Voltage CMOS Operational Amplifiers can be read and enjoyed by those without much experience in analog circuit design. It is an invaluable reference boo...

  9. Operation and maintenance requirements of system design bases

    International Nuclear Information System (INIS)

    Banerjee, A.K.; Hanley, N.E.

    1989-01-01

    All system designs make assumptions about system operation testing, inspection, and maintenance. Existing industry codes and standards explicitly address design requirements of new systems, while issues related to system and plant reliability, life, design margins, effects of service conditions, operation, maintenance, etc., usually are implicit. However, system/component design documents of existing power plants often address the code requirements without considering the operation, maintenance, inspection, and testing (OMIT) requirements. The nuclear industry is expending major efforts at most nuclear power plants to reassemble and/or reconstitute system design bases. Stone ampersand Webster Engineering Corporation (SWEC) recently addressed the OMIT requirements of system/component design as an integral part of a utility's preventive maintenance program. For each component, SWEC reviewed vendor recommendations, NPRDS data/industry experience, the existing maintenance program, component service conditions, and actual plant experience. A maintenance program that considers component service conditions and plant experience ensures a connection between maintenance and design basis. Root cause analysis of failure and engineering evaluation of service condition are part of the program. System/component OMIT requirements also are compared against system design, service condition, degradation mechanism, etc., through system/component life-cycle evaluation

  10. Operability design review of prototype large breeder reactor (PLBR) designs. Final report, September 1981

    International Nuclear Information System (INIS)

    Beakes, J.H.; Ehman, J.R.; Jones, H.M.; Kinne, B.V.T.; Price, C.M.; Shores, S.P.; Welch, J.K.

    1981-09-01

    Prototype Large Breeder Reactor (PLBR) designs were reviewed by personnel with extensive power plant operations experience. Fourteen normal and off-normal events, such as startup, shutdown, refueling, reactor scram and loss of feedwater, were evaluated using an operational evaluation methodology which is designed to facilitate talk-through sessions on operational events. Human factors engineers participated in the review and assisted in developing and refining the review methodologies. Operating experience at breeder reactor facilities such as Experimental Breeder Reactor-II (EBR-II), Enrico Fermi Atomic Power Plant - Unit 1, and the Fast Flux Test Facility (FFTF) was gathered, analyzed, and used to determine whether lessons learned from operational experience had been incorporated into the PLBR designs. This eighteen month effort resulted in approximately one hundred specific recommendations for improving the operability of PLBR designs

  11. Design and development of remotely operated coolant channel cutting machine

    International Nuclear Information System (INIS)

    Suthar, R.L.; Sinha, A.K.; Srikrishnamurty, G.

    1994-01-01

    One of the coolant tubes of Narora Atomic Power Station (NAPS) reactor needs to be removed. To remove a coolant tube, four cutting operations, (liner tube cutting, end-fitting cutting, machining of seal weld of bellow ring and finally coolant tube cutting) are required to be carried out. A remotely operated cutting machine to carry out all these operations has been designed and developed by Central Workshops. This machine is able to cut at the exact location because of numerically controlled axial and radial travel of tool. Only by changing the tool head and tool holder, same machine can be used for various types of cutting/machining operations. This report details the design, manufacture, assembly and testing work done on the machine. (author). 4 figs

  12. Design, Fabrication, and Initial Operation of a Reusable Irradiation Facility

    International Nuclear Information System (INIS)

    Heatherly, D.W.; Thoms, K.R.; Siman-Tov, I.I.; Hurst, M.T.

    1999-01-01

    A Heavy-Section Steel Irradiation (HSSI) Program project, funded by the US Nuclear Regulatory Commission, was initiated at Oak Ridge National Laboratory to develop reusable materials irradiation facilities in which metallurgical specimens of reactor pressure vessel steels could be irradiated. As a consequence, two new, identical, reusable materials irradiation facilities have been designed, fabricated, installed, and are now operating at the Ford Nuclear Reactor at the University of Michigan. The facilities are referred to as the HSSI-IAR facilities with the individual facilities being designated as IAR-1 and IAR-2. This new and unique facility design requires no cutting or grinding operations to retrieve irradiated specimens, all capsule hardware is totally reusable, and materials transported from site to site are limited to specimens only. At the time of this letter report, the facilities have operated successfully for approximately 2500 effective full-power hours

  13. Knowledge representation and knowledge base design for operator advisor system

    International Nuclear Information System (INIS)

    Hangos, K.M.; Sziano, T.; Tapolcai, L.

    1990-01-01

    The problems of knowledge representation, knowledge base handling and design has been described for an Operator Advisor System in the Paks Nuclear Power Plant. The Operator Advisor System is to be implemented as a part of the 5th and 6th unit. The knowledge of the Operator Advisor system is described by a few elementary knowledge items (diagnostic event functions, fault graph, action trees), weighted directed graphs have been found as their common structure. List-type and relational representation of these graphs have been used for the on-line and off-line part of the knowledge base respectively. A uniform data base design and handling has been proposed which consists of a design system, a knowledge base editor and a knowledge base compiler

  14. OPERATIONS RESEARCH IN THE DESIGN OF MANAGEMENT INFORMATION SYSTEMS

    Science.gov (United States)

    management information systems is concerned with the identification and detailed specification of the information and data processing...of advanced data processing techniques in management information systems today, the close coordination of operations research and data systems activities has become a practical necessity for the modern business firm.... information systems in which mathematical models are employed as the basis for analysis and systems design. Operations research provides a

  15. Designing for nuclear power plant maintainability and operability

    International Nuclear Information System (INIS)

    Pedersen, T.J.

    1998-01-01

    Experience has shown that maintenance and operability aspects must be addressed in the design work. ABB Atom has since long an ambition of achieving optimised, overall plant designs, and efficient feedback of growing operating experience has stepwise eliminated shortcomings, and yielded better and better plant operating performances. The records of the plants of the latest design versions are very good; four units in Sweden have operated at an energy availability of 90.1%, and the two Olkiluoto units in Finland at a load factor of 92.7%, over the last decade. The occupational radiation exposures have also been at a low level. The possibilities for implementing 'lessons learned' in existing plants are obviously limited by practical constraints. In Finland and Sweden, significant modernisations are still underway, however, involving replacement of mechanical equipment, and upgrading and backfitting of I and C systems on a large scale, in most of the plants. The BWR 90 design focuses on meeting requirements from utilities as well as new regulatory requirements, with a particular emphasis on the consequences of severe accidents; there shall be no large releases to the environment. Other design improvements involve: all-digital I and C systems and enhanced human factors engineering to improve work environment for operators, optimisation of buildings and containment to decrease construction time and costs, and selection of materials as well as maintenance of operating procedures to reduce radiation exposures even further. The BWR 90 design was offered to Finland in the early 1990s, but development work continues. It has been selected by a number of European utilities for assessing its conformance with the European Utility Requirements (EUR), aiming at a specific EUR Volume 3 for the BWR 90. Some characteristics of the ABB BWRs, with emphasis on features of importance for achieving improved economy and enhanced safety, are described below. (author)

  16. Embedded real-time operating system micro kernel design

    Science.gov (United States)

    Cheng, Xiao-hui; Li, Ming-qiang; Wang, Xin-zheng

    2005-12-01

    Embedded systems usually require a real-time character. Base on an 8051 microcontroller, an embedded real-time operating system micro kernel is proposed consisting of six parts, including a critical section process, task scheduling, interruption handle, semaphore and message mailbox communication, clock managent and memory managent. Distributed CPU and other resources are among tasks rationally according to the importance and urgency. The design proposed here provides the position, definition, function and principle of micro kernel. The kernel runs on the platform of an ATMEL AT89C51 microcontroller. Simulation results prove that the designed micro kernel is stable and reliable and has quick response while operating in an application system.

  17. Deepen the Teaching Reform of Operating System, Cultivate the Comprehensive Quality of Students

    Science.gov (United States)

    Liu, Jianjun

    2010-01-01

    Operating system is the core course of the specialty of computer science and technology. To understand and master the operating system will directly affect students' further study on other courses. The course of operating system focuses more on theories. Its contents are more abstract and the knowledge system is more complicated. Therefore,…

  18. The assessment of eco-design with a comprehensive index incorporating environmental impact and economic profit

    Science.gov (United States)

    Yang, Shuo; Fu, Yun; Wang, Xiuteng; Xu, Bingsheng; Li, Zheng

    2017-11-01

    Eco-design is an advanced design approach which plays an important part in the national innovation project and serves as a key point for the successful transformation of the supply structure. However, the practical implementation of the pro-environmental designs and technologies always faces a dilemma situation, where some processes can effectively control their emissions to protect the environment at relatively high costs, while others pursue the individual interest in making profit by ignoring the possible adverse environmental impacts. Thus, the assessment on the eco-design process must be carried out based on the comprehensive consideration of the economic and environmental aspects. Presently, the assessment systems in China are unable to fully reflect the new environmental technologies regarding their innovative features or performance. Most of the assessment systems adopt scoring method based on the judgments of the experts, which are easy to use but somewhat subjective. The assessment method presented in this paper includes the environmental impact (EI) assessment based on LCA principal and willingness-to-pay theory, and economic profit (EP) assessment mainly based on market price. The results from the assessment are in the form of EI/EP, which evaluate the targeted process from a combined perspective of environmental and economic performance. A case study was carried out upon the utilization process of coal fly ash, which indicates the proposed method can compare different technical processes in an effective and objective manner, and provide explicit and insightful suggestions for decision making.

  19. Axiomatic Design of a Framework for the Comprehensive Optimization of Patient Flows in Hospitals

    Directory of Open Access Journals (Sweden)

    Gabriele Arcidiacono

    2017-01-01

    Full Text Available Lean Management and Six Sigma are nowadays applied not only to the manufacturing industry but also to service industry and public administration. The manifold variables affecting the Health Care system minimize the effect of a narrow Lean intervention. Therefore, this paper aims to discuss a comprehensive, system-based approach to achieve a factual holistic optimization of patient flows. This paper debates the efficacy of Lean principles applied to the optimization of patient flows and related activities, structures, and resources, developing a theoretical framework based on the principles of the Axiomatic Design. The demand for patient-oriented and efficient health services leads to use these methodologies to improve hospital processes. In the framework, patients with similar characteristics are clustered in families to achieve homogeneous flows through the value stream. An optimization checklist is outlined as the result of the mapping between Functional Requirements and Design Parameters, with the right sequence of the steps to optimize the patient flow according to the principles of Axiomatic Design. The Axiomatic Design-based top-down implementation of Health Care evidence, according to Lean principles, results in a holistic optimization of hospital patient flows, by reducing the complexity of the system.

  20. Axiomatic Design of a Framework for the Comprehensive Optimization of Patient Flows in Hospitals

    Science.gov (United States)

    Arcidiacono, Gabriele; Matt, Dominik T.; Rauch, Erwin

    2017-01-01

    Lean Management and Six Sigma are nowadays applied not only to the manufacturing industry but also to service industry and public administration. The manifold variables affecting the Health Care system minimize the effect of a narrow Lean intervention. Therefore, this paper aims to discuss a comprehensive, system-based approach to achieve a factual holistic optimization of patient flows. This paper debates the efficacy of Lean principles applied to the optimization of patient flows and related activities, structures, and resources, developing a theoretical framework based on the principles of the Axiomatic Design. The demand for patient-oriented and efficient health services leads to use these methodologies to improve hospital processes. In the framework, patients with similar characteristics are clustered in families to achieve homogeneous flows through the value stream. An optimization checklist is outlined as the result of the mapping between Functional Requirements and Design Parameters, with the right sequence of the steps to optimize the patient flow according to the principles of Axiomatic Design. The Axiomatic Design-based top-down implementation of Health Care evidence, according to Lean principles, results in a holistic optimization of hospital patient flows, by reducing the complexity of the system. © 2017 Gabriele Arcidiacono et al.

  1. Design features and operating characteristics of the MC-50 cyclotron

    International Nuclear Information System (INIS)

    Bak, Hae Ill; Bak, Joo Shik

    1989-01-01

    The MC-50 cyclotron at Korean Cancer Center Hospital is now operational for neutron therapy and medical radioisotope production. Design features, mechanical structures and operating characteristics of the MC-50 are described in this paper. Optimum operating condition for this cyclotron has been determined by the repetitive running, and the performances of the internal beam have been investigated through the measurements of intensity and spatial distribution of the internal beam as a function of the radius of the cyclotron. Routinely, the 40 μA of 50 MeV protons have been obtained at first Faraday cup with a extraction efficiency of 61%. (Author)

  2. Ergonomics design and operator training as contributors to human reliability

    International Nuclear Information System (INIS)

    Jackson, A.R.G.; Madden, V.J.; Umbers, I.G.; Williams, J.C.

    1987-01-01

    The safe operation of nuclear reactors depends not only on good physical safety engineering but on the human operators as well. The Central Electricity Generating Board's approach to human reliability includes the following aspects: ergonomics design (task analysis and the development of man-machine interfaces), analysis of human reliability, operational feedback, staff training and assessment, maintenance management, research programmes and management. This paper describes how these combine to achieve the highest practicable level of human reliability, not only for the Sizewell-B pressurized water reactor, but also for the Board's gas-cooled reactors. Examples are used to illustrate the topics considered. (UK)

  3. Practical considerations in the design and operation of superconducting structures

    International Nuclear Information System (INIS)

    Schwettman, H.A.

    1975-01-01

    During the past few years, considerable experience has been gained in the operation of prototype superconducting accelerators under beam line conditions. As a result of this experience, important aspects of structure design and important questions related to the long term operation of superconducting structures have been brought into sharper focus. For applications where low power loss and high duty factor, or exceptional beam quality and stable operation, are essential properties, and where modest energy gradients can be tolerated, superconducting structures are distinctly superior to conventional room temperature structures. (auth)

  4. Design of an operations manager selection system in service encounter

    Directory of Open Access Journals (Sweden)

    Tanawin Nunthaphanich

    2015-10-01

    Full Text Available The purpose of this study is to provide criteria for selecting operations managers at the ‘service encounter’ for mobile telecommunication companies, and develop a system for this multi-criteria decision-making scheme based on the Analytical Hierarchy Process (AHP. There are three main criteria for evaluating the capability of service-encounter operation managers: (1 the ability to design service process; (2 the ability to operate service process; (3 the ability to conduct improvement. The AHP operation manager selection tool was developed based on the complex problems at the service encounter. It was created as a decision support system which was used to recruit and evaluate operations managers’ capability for the purpose of career advancement.

  5. Job training planning and design for process plant operators

    Energy Technology Data Exchange (ETDEWEB)

    Wirstad, J.

    1983-01-01

    A method is presented by which process plant operators for nuclear power plants are trained in Sweden. It works by a top-down method of systems analysis which can be integrated into the analysis, specification, and design of the process automation system. The training methods can also be adapted to existing automation systems and operating schedules. The author's method is based on the principle that training programs should be based on job requirements, e.g. operator tasks in common, less frequent, and rare operating conditions. Procedures have been tested for the following steps: Job analysis, analysis of knowledge and experience required, analysis of operator training requirements, set-up and organisation of the training programme, achievement control, evaluation of the training programme.

  6. Job training planning and design for process plant operators

    International Nuclear Information System (INIS)

    Wirstad, J.

    1983-01-01

    A method is presented by which process plant operators for nuclear power plants are trained in Sweden. It works by a top-down method of systems analysis which can be integrated into the analysis, specification, and design of the process automation system. The training methods can also be adapted to existing automation systems and operating schedules. The author's method is based on the principle that training programs should be based on job requirements, e.g. operator tasks in common, less frequent, and rare operating conditions. Procedures have been tested for the following steps: Job analysis, analysis of knowledge and experience required, analysis of operator training requirements, set-up and organisation of the training programme, achievement control, evaluation of the training programme. (orig./HP) [de

  7. Role of operator response guidelines in CANDU 9 design program

    International Nuclear Information System (INIS)

    Jaitly, R.K.

    2000-01-01

    The CANDU 9 is a large version of the CANDU Pressurized Heavy Water Reactor (PHWR) system developed in Canada. With an electrical output of approximately 935 MWe, the CANDU 9 complements the established mid-size CANDU 6 (700 MWe) and makes use of proven technology updated with state of the art features resulting from ongoing development. The CANDU 9 builds on the reactor and process system designs of the operating Darlington and Bruce B plants, and incorporates a modified CANDU 6 station layout, as well as improved construction methods and operational features. A high level of standardization has always been a feature of CANDU reactors. This theme is emphasized in the CANDU 9; all key components (reactor core, steam generators, coolant pumps, pressure tubes, etc.) are of the same design as those proven in service in the operating CANDU power stations. Including Probabilistic Safety Assessment (PSA) as part of the CANDU 9 design process from the outset of the program was seen as key to ensuring completeness of safety related requirements. The PSA work provided an in-depth understanding of the plant response to various postulated accidents. As well, the time frame for recovery and the related operator actions were identified. This information together with AECL's experience in supporting the development of Emergency Operating Procedures (EOPs) for the operating CANDU reactors are the basis for preparation of CANDU 9 Operator Response Guidelines (ORGs). Technical content, format and human factors considerations adopted for the ORGs are such that these can be readily converted to EOPs. The scope of ORGs includes generic as well as event specific ORGs. This dual approach is required to provide defense-in-depth. This paper describes the process used to prepare ORGs for the CANDU 9 reactor and discusses important benefits gained from the application of ORGs as input to the control center design and future preparation of the EOPs. (author)

  8. The Stochastic Multicloud Model as part of an operational convection parameterisation in a comprehensive GCM

    Science.gov (United States)

    Peters, Karsten; Jakob, Christian; Möbis, Benjamin

    2015-04-01

    An adequate representation of convective processes in numerical models of the atmospheric circulation (general circulation models, GCMs) remains one of the grand challenges in atmospheric science. In particular, the models struggle with correctly representing the spatial distribution and high variability of tropical convection. It is thought that this model deficiency partly results from formulating current convection parameterisation schemes in a purely deterministic manner. Here, we use observations of tropical convection to inform the design of a novel convection parameterisation with stochastic elements. The novel scheme is built around the Stochastic MultiCloud Model (SMCM, Khouider et al 2010). We present the progress made in utilising SMCM-based estimates of updraft area fractions at cloud base as part of the deep convection scheme of a GCM. The updraft area fractions are used to yield one part of the cloud base mass-flux used in the closure assumption of convective mass-flux schemes. The closure thus receives a stochastic component, potentially improving modeled convective variability and coherence. For initial investigations, we apply the above methodology to the operational convective parameterisation of the ECHAM6 GCM. We perform 5-year AMIP simulations, i.e. with prescribed observed SSTs. We find that with the SMCM, convection is weaker and more coherent and continuous from timestep to timestep compared to the standard model. Total global precipitation is reduced in the SMCM run, but this reduces i) the overall error compared to observed global precipitation (GPCP) and ii) middle tropical tropospheric temperature biases compared to ERA-Interim. Hovmoeller diagrams indicate a slightly higher degree of convective organisation compared to the base case and Wheeler-Kiladis frequency wavenumber diagrams indicate slightly more spectral power in the MJO range.

  9. Applying principles of Design For Assembly to ITER maintenance operations

    International Nuclear Information System (INIS)

    Heemskerk, Cock; de Baar, Marco; Elzendoorn, Ben; Koning, Jarich; Verhoeven, Toon; Vreede, Fred de

    2009-01-01

    In ITER, maintenance operations in the vessel and in the Hot Cell will be largely done by Remote Handling (RH). Remotely performed maintenance actions tend to be more time-costly than actions performed by direct human access. With a human operator in the control loop and adequate situational feedback, a two-armed master slave manipulator system can mimic direct access with dexterous manipulation, tactile feedback and vision. But even then, turnaround times are still very high. Adapting the design for simplified maintenance operations can yield significant time savings. One of the methods known to produce a simpler, more robust design, which is also better suited for handling with robots, is Design For Assembly (DFA). This paper discusses whether and how the principles of DFA can be applied to simplify maintenance operations for ITER. While DFA is normally used with series-production and ITER is a unique product, it is possible to apply the principles of DFA to ITER maintenance operations. Furthermore, DFA's principles can be applied at different abstraction levels. Combining principles of DFA with Virtual Reality leads to new insights and provides additional value.

  10. Design of casks: incorporating operational feedback from maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Bimet, F.; Hartenstein, M. [COGEMA Logistics, Saint Quentin (France)

    2004-07-01

    Casks are designed to conform to regulations and to client specifications. Essential areas such as easy operation, low costs of maintenance, low operation and maintenance doses, limited waste, are not explicitly covered. Notwithstanding, COGEMA LOGISTICS uses all feedback available, so that casks are designed to be easy, safe and economical to operate and maintain. Maintenance is an activity where you do spot items that old-time designers could have made better, and things that users should not have done. Thanks to quality assurance, there are a number of data available, waiting to be collected and exploited; they have to be identified, located, retrieved, and analysed. Using information such as wear, damage, use of spare parts, access problems helps to make casks ever better. It leads to more efficient concepts, and to upgrades on existing designs; it also allows to integrate environmental considerations, inter alia in the choice of materials and in maintenance methods. It is necessary for the designer to interact with the users, the cask owners, the maintenance providers, in order to gather all relevant information and events. This is made easier when all these actors are ''under one roof'', or have very close ties. This paper presents COGEMA LOGISTICS methods for collecting and analysing all these experiences waiting to be used. It explains our process for analysing data, preparing yearly reports that are made available to our designers. It describes how each new design is subject to a maintainability study, using this feedback, so that the cask safety is always assured, that radiological doses are kept to a minimum, and that operating and maintenance costs will remain as low as possible.

  11. Design of casks: incorporating operational feedback from maintenance

    International Nuclear Information System (INIS)

    Bimet, F.; Hartenstein, M.

    2004-01-01

    Casks are designed to conform to regulations and to client specifications. Essential areas such as easy operation, low costs of maintenance, low operation and maintenance doses, limited waste, are not explicitly covered. Notwithstanding, COGEMA LOGISTICS uses all feedback available, so that casks are designed to be easy, safe and economical to operate and maintain. Maintenance is an activity where you do spot items that old-time designers could have made better, and things that users should not have done. Thanks to quality assurance, there are a number of data available, waiting to be collected and exploited; they have to be identified, located, retrieved, and analysed. Using information such as wear, damage, use of spare parts, access problems helps to make casks ever better. It leads to more efficient concepts, and to upgrades on existing designs; it also allows to integrate environmental considerations, inter alia in the choice of materials and in maintenance methods. It is necessary for the designer to interact with the users, the cask owners, the maintenance providers, in order to gather all relevant information and events. This is made easier when all these actors are ''under one roof'', or have very close ties. This paper presents COGEMA LOGISTICS methods for collecting and analysing all these experiences waiting to be used. It explains our process for analysing data, preparing yearly reports that are made available to our designers. It describes how each new design is subject to a maintainability study, using this feedback, so that the cask safety is always assured, that radiological doses are kept to a minimum, and that operating and maintenance costs will remain as low as possible

  12. New Clean Air Act complicates power plant operation, design

    International Nuclear Information System (INIS)

    Smock, R.W.

    1991-01-01

    In November the president signed into law the new Clean Air Act, ushering in a new era in the power generation industry. This paper reviews the six important sections of the Clean Air Act and their impact on power plant operation and design

  13. 40 CFR 264.221 - Design and operating requirements.

    Science.gov (United States)

    2010-07-01

    ..., and other equipment; and human error. (h) A surface impoundment must have dikes that are designed... (CONTINUED) STANDARDS FOR OWNERS AND OPERATORS OF HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES... external hydrogeologic forces), physical contact with the waste or leachate to which they are exposed...

  14. Comparative Analysis of Possible Designs for Flexible Distribution System Operation

    DEFF Research Database (Denmark)

    Lin, Jeremy; Knezovic, Katarina

    2016-01-01

    for achieving the most efficient utilization of these resources while meeting the forecasted load. In this paper, we present possible system design frameworks proposed for flexible distribution system operation. Critical evaluations and comparison of these models are made based on a number of key attributes...

  15. Design and operations at the National Tritium Labelling Facility

    International Nuclear Information System (INIS)

    Morimoto, H.; Williams, P.G.

    1991-09-01

    The National Tritium Labelling Facility (NTLF) is a multipurpose facility engaged in tritium labeling research. It offers to the biomedical research community a fully equipped laboratory for the synthesis and analysis of tritium labeled compounds. The design of the tritiation system, its operations and some labeling techniques are presented

  16. Small nuclear reactor safety design requirements for autonomous operation

    International Nuclear Information System (INIS)

    Kozier, K.S.; Kupca, S.

    1997-01-01

    Small nuclear power reactors offer compelling safety advantages in terms of the limited consequences that can arise from major accident events and the enhanced ability to use reliable, passive means to eliminate their occurrence by design. Accordingly, for some small reactor designs featuring a high degree of safety autonomy, it may be-possible to delineate a ''safety envelope'' for a given set of reactor circumstances within which safe reactor operation can be guaranteed without outside intervention for time periods of practical significance (i.e., days or weeks). The capability to operate a small reactor without the need for highly skilled technical staff permanently present, but with continuous remote monitoring, would aid the economic case for small reactors, simplify their use in remote regions and enhance safety by limiting the potential for accidents initiated by inappropriate operator action. This paper considers some of the technical design options and issues associated with the use of small power reactors in an autonomous mode for limited periods. The focus is on systems that are suitable for a variety of applications, producing steam for electricity generation, district heating, water desalination and/or marine propulsion. Near-term prospects at low power levels favour the use of pressurized, light-water-cooled reactor designs, among which those having an integral core arrangement appear to offer cost and passive-safety advantages. Small integral pressurized water reactors have been studied in many countries, including the test operation of prototype systems. (author)

  17. Computational tools for cyclotron design, commissioning, and operation

    International Nuclear Information System (INIS)

    Kost, C.J.

    1989-05-01

    Many support systems are required in the design, commissioning, and normal operation of a modern cyclotron. Presented is an overview of the computing environment developed during these various stages at TRIUMF. The current computing environment is also discussed, with emphasis on how one can provide an integrated system which is user-friendly

  18. Cognitive task analysis and the design of computerized operator aids

    International Nuclear Information System (INIS)

    Andersson, H.

    1985-01-01

    The new technological possibilities have led to the initiation of many projects for the design and evaluation of computerized operator support systems to be implemented in nuclear power plant control rooms. A typical finding so far has been that operators often have a positive attitude towards such systems but still don't use them very much, mostly because they find almost the same information on the conventional control boards which they are accustomed to use. Still, however, there is a widely shared belief that conventional control rooms have short-comings that make the use of computerized aids necessary. One reason for the limited success so far is that the new systems often are poorly integrated with the existing conventional instrumentation and with the working procedures. The reluctance to use new computer based aids, despite their nice features, is therefore probably caused by an inadequate task analysis made prior to the design of these computerized operator support systems

  19. Examples of radiation protection optimization in design and operation

    International Nuclear Information System (INIS)

    Gonzalez, A.J.; Palacios, E.; Curti, A.; Agatiello, O.; Majchrzak, J.

    1982-01-01

    The practical use of the requirement of optimization of radiological protection is presented. Application examples for designing ventilation systems and for maintenance operations of nuclear plants are given. A method is developed for the application of the optimization requirement to the design of ventilation systems in contaminated environments. Representative values of the main parameters are presented and their relevant features are discussed. A practical example shows actual results for a radioisotope production plant. Causes influencing collective doses incurred by the workers during maintenance operations are analyzed. A method is presented for the optimization of both the level of training of personnel and the apportionment of individual doses. As an example, this methodology is applied to the maintenance operations in a nuclear power plant. (author)

  20. Focused cathode design to reduce anode heating during vircator operation

    Energy Technology Data Exchange (ETDEWEB)

    Lynn, Curtis F.; Dickens, James C.; Neuber, Andreas A. [Center for Pulsed Power and Power Electronics, Department of Electrical and Computer Engineering, Texas Tech University, Lubbock, Texas 79409 (United States)

    2013-10-15

    Virtual cathode oscillators, or vircators, are a type of high power microwave device which operates based on the instability of a virtual cathode, or cloud of electrons, which forms when electron current injected into the drift tube exceeds the space charge limited current within the drift tube. Anode heating by the electron beam during vircator operation ultimately limits achievable pulse lengths, repetition rates, and the duration of burst mode operation. This article discusses a novel cathode design that focuses electrons through holes in the anode, thus significantly reducing anode heating by the electrons emitted from the cathode during the first transit through the A-K gap. Reflexing electrons continue to deposit energy on the anode; however, the discussed minimization of anode heating by main beam electrons has the potential to enable higher repetition rates as well as efficiency and longer diode lifetime. A simulation study of this type of cathode design illustrates possible advantages.

  1. Design and Realization of Silhouette Operation Platform Based on GIS

    Science.gov (United States)

    Fu, Jia; Cui, Xinqiang; Yuan, Zhengteng

    2018-01-01

    Artificial weather effects after several generations of unremitting efforts in many provinces, municipalities and districts have become a regular business to serve the community. In the actual operation of the actual impact of weather operations, onsite job terminal system functional integration is not high, such as the operation process cumbersome operation instructions unreasonable, the weather data lag, the data form of a single factor and other factors seriously affect the weather conditions, Sexual and intuitive improvement. Therefore, this paper adopts the Android system as the carrier for the design and implementation of the silhouette intelligent terminal system. The intelligent terminal system has carried on the preliminary deployment trial in the real-time intelligent command system which realizes the weather operation in a province, and has formed a centralized, unified and digital artificial influence in combination with the self-developed multi-function server system platform and the remote centre command system Weather operation communication network, to achieve intelligent terminal and remote centre commander between the efficient, timely and stable information exchange, improve the shadow of the economic and social benefits, basically reached the initial design purpose.

  2. Design, installation, and initial use of a smart operator aid

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, J A; Lau, S H; Kwok, Kwan S; Kim, Keung Koo [Nuclear Reactor Laboratory, Massachusetts Institute of Technology, Cambridge, MA (United States)

    1992-07-01

    This paper reviews the design, installation, and initial use of a smart operator aid that was developed to assist licensed personnel with the performance of power adjustments on the 5-MWt MIT Research Reactor (MITR-II). The aid is a computer-generated, predictive display that enables console operators to visualize the consequences of a planned control action prior to implementing that action. The motivation for the development of this display was the observation that present-time control decisions are made by comparing a plant's expected behavior to the desired response. Thus, an operator will achieve proper control only to the degree that he or she is capable of anticipating plant response. This may be difficult if the plant's dynamics are non-linear, time delayed, or counter-intuitive. A study was therefore undertaken at the MITR-II to determine whether operator performance could be improved by using digital technology to provide visual displays of projected plant behavior. It was found that, while the use of predictive information had to be learned, operator performance did improve as a result of its availability. Information is presented on the display's design, the computer system utilized for its implementation, operator response to the display, and the possible extension of this concept to the control of steam generator level. (author)

  3. Design, installation, and initial use of a smart operator aid

    International Nuclear Information System (INIS)

    Bernard, J.A.; Lau, S.H.; Kwok, Kwan S.; Kim, Keung Koo

    1992-01-01

    This paper reviews the design, installation, and initial use of a smart operator aid that was developed to assist licensed personnel with the performance of power adjustments on the 5-MWt MIT Research Reactor (MITR-II). The aid is a computer-generated, predictive display that enables console operators to visualize the consequences of a planned control action prior to implementing that action. The motivation for the development of this display was the observation that present-time control decisions are made by comparing a plant's expected behavior to the desired response. Thus, an operator will achieve proper control only to the degree that he or she is capable of anticipating plant response. This may be difficult if the plant's dynamics are non-linear, time delayed, or counter-intuitive. A study was therefore undertaken at the MITR-II to determine whether operator performance could be improved by using digital technology to provide visual displays of projected plant behavior. It was found that, while the use of predictive information had to be learned, operator performance did improve as a result of its availability. Information is presented on the display's design, the computer system utilized for its implementation, operator response to the display, and the possible extension of this concept to the control of steam generator level. (author)

  4. Design and Construction of Operation Bridge for Research Reactor

    International Nuclear Information System (INIS)

    Jung, Kwangsub; Choi, Jinbok; Lee, Jongmin; Oh, Jinho

    2015-01-01

    The operation bridge contains a lower working deck mounted on a saddle that travels on rails. Upright members are mounted on the saddle to support the upper structure and two hoist monorails. The saddle contains an anti-derail system that is composed of seismic lugs and guide rollers. The operation bridge travels along the rails to transport the fuel assembly, irradiated object, and reactor components in the pools by using tools. Hoists are installed at the top girder. The hoist is suspended from the monorail by means of a motor driven trolley that runs along the monorail. Movements of hoist and trolley are controlled by using the control pendant switch. Processes of design and construction of the operation bridge for the research reactor are introduced. The operation bridge is designed under consideration of functions of handling equipment in the pool and operational limits for safety. Structural analysis is carried out to evaluate the structural integrity in the seismic events. Tests and inspections are also performed during fabrication and installation to confirm the function and safety of the operation bridge

  5. Design, installation, and initial use of a smart operator aid

    International Nuclear Information System (INIS)

    Bernard, J.A.; Lau, Shing Hei; Kwok, K.S.; Kim, Keung Koo

    1992-01-01

    This paper reviews the design, installation, and initial use of a smart operator aid that was developed to assist licensed personnel with the performance of power adjustments on the 5-MWt MIT Research Reactor (MITR-II). The aid is a computer-generated, predictive display that enables console operators to visualize the consequences of a planned control action prior to implementing that action. The motivation for the development of this display was the observation that present-time control decisions are made by comparing a plant's expected behavior to the desired response. Thus, an operator will achieve proper control only to the degree that he or she is capable of anticipating plant response. This may be difficult if the plant's dynamics are non-linear, time delayed, or counter-intuitive. A study was therefore undertaken at the MITR-11 to determine whether operator performance could be improved by using digital technology to provide visual displays of projected plant behavior. It was found that, while the use of predictive information had to be learned, operator performance did improve as a result of its availability. Information is presented on the display's design, the computer system utilized for its implementation, operator response to the display, and the possible extension of this concept to the control of steam generator level. 16 refs., 8 figs

  6. Operation and design selection of high temperature superconducting magnetic bearings

    International Nuclear Information System (INIS)

    Werfel, F N; Floegel-Delor, U; Riedel, T; Rothfeld, R; Wippich, D; Goebel, B

    2004-01-01

    Axial and radial high temperature superconducting (HTS) magnetic bearings are evaluated by their parameters. Journal bearings possess advantages over thrust bearings. High magnetic gradients in a multi-pole permanent magnet (PM) configuration, the surrounding melt textured YBCO stator and adequate designs are the key features for increasing the overall bearing stiffness. The gap distance between rotor and stator determines the specific forces and has a strong impact on the PM rotor design. We report on the designing, building and measuring of a 200 mm prototype 100 kg HTS bearing with an encapsulated and thermally insulated melt textured YBCO ring stator. The encapsulation requires a magnetically large-gap (4-5 mm) operation but reduces the cryogenic effort substantially. The bearing requires 3 l of LN 2 for cooling down, and about 0.2 l LN 2 h -1 under operation. This is a dramatic improvement of the efficiency and in the practical usage of HTS magnetic bearings

  7. The Algorithm for Algorithms: An Evolutionary Algorithm Based on Automatic Designing of Genetic Operators

    Directory of Open Access Journals (Sweden)

    Dazhi Jiang

    2015-01-01

    Full Text Available At present there is a wide range of evolutionary algorithms available to researchers and practitioners. Despite the great diversity of these algorithms, virtually all of the algorithms share one feature: they have been manually designed. A fundamental question is “are there any algorithms that can design evolutionary algorithms automatically?” A more complete definition of the question is “can computer construct an algorithm which will generate algorithms according to the requirement of a problem?” In this paper, a novel evolutionary algorithm based on automatic designing of genetic operators is presented to address these questions. The resulting algorithm not only explores solutions in the problem space like most traditional evolutionary algorithms do, but also automatically generates genetic operators in the operator space. In order to verify the performance of the proposed algorithm, comprehensive experiments on 23 well-known benchmark optimization problems are conducted. The results show that the proposed algorithm can outperform standard differential evolution algorithm in terms of convergence speed and solution accuracy which shows that the algorithm designed automatically by computers can compete with the algorithms designed by human beings.

  8. Design, analysis, operation, and advanced control of hybrid renewable energy systems

    Science.gov (United States)

    Whiteman, Zachary S.

    Because using non-renewable energy systems (e.g., coal-powered co-generation power plants) to generate electricity is an unsustainable, environmentally hazardous practice, it is important to develop cost-effective and reliable renewable energy systems, such as photovoltaics (PVs), wind turbines (WTs), and fuel cells (FCs). Non-renewable energy systems, however, are currently less expensive than individual renewable energy systems (IRESs). Furthermore, IRESs based on intermittent natural resources (e.g., solar irradiance and wind) are incapable of meeting continuous energy demands. Such shortcomings can be mitigated by judiciously combining two or more complementary IRESs to form a hybrid renewable energy system (HRES). Although previous research efforts focused on the design, operation, and control of HRESs has proven useful, no prior HRES research endeavor has taken a systematic and comprehensive approach towards establishing guidelines by which HRESs should be designed, operated, and controlled. The overall goal of this dissertation, therefore, is to establish the principles governing the design, operation, and control of HRESs resulting in cost-effective and reliable energy solutions for stationary and mobile applications. To achieve this goal, we developed and demonstrated four separate HRES principles. Rational selection of HRES type: HRES components and their sizes should be rationally selected using knowledge of component costs, availability of renewable energy resources, and expected power demands of the application. HRES design: by default, the components of a HRES should be arranged in parallel for increased efficiency and reliability. However, a series HRES design may be preferred depending on the operational considerations of the HRES components. HRES control strategy selection: the choice of HRES control strategy depends on the dynamics of HRES components, their operational considerations, and the practical limitations of the HRES end-use. HRES data

  9. A comprehensive framework to quantify energy savings potential from improved operations of commercial building stocks

    International Nuclear Information System (INIS)

    Azar, Elie; Menassa, Carol C.

    2014-01-01

    While studies highlight the significant impact of actions performed by occupants and facility managers on building energy performance, current policies ignore the importance of human actions and the potential energy savings from a more efficient operation of building systems. This is mainly attributed to the lack of methods that evaluate non-technological drivers of energy use for large stocks of commercial buildings to support policy making efforts. Therefore, this study proposes a scientific approach to quantifying the energy savings potential due to improved operations of any stock of commercial buildings. The proposed framework combines energy modeling techniques, studies on human actions in buildings, and surveying and sampling methods. The contributions of this study to energy policy are significant as they reinforce the role of human actions in energy conservation, and support efforts to integrate operation-focused solutions in energy conservation policy frameworks. The framework's capabilities are illustrated in a case study performed on the stock of office buildings in the United States (US). Results indicate a potential 21 percent reduction in the current energy use levels of these buildings through realistic changes in current building operation patterns. - Highlights: • Human actions highly influence energy performance of commercial building stocks. • It is challenging to quantify operation-related energy savings potential. • The proposed framework quantifies potential energy savings from improved operations. • The framework can be applied on any stock of commercial buildings. • Applications include support for operation-focused solutions in energy policies

  10. Efficient design and operation of a data acquisition system for pressurized pipeline systems.

    Science.gov (United States)

    Kim, S

    2006-01-01

    The unsteady flow analysis of pipeline systems provides useful guidelines for implementing data acquisition components such as data filtering ranges, sensor locations and sampling frequencies. A theoretical integration among hydraulics, free vibration analysis and signal processing is proposed for a comprehensive approach aiming at enhanced design and operation of data acquisition system. Transient analysis is performed to extract flow variation by a valve modulation in a pipeline system. Frequency transformation analysis is developed to convert pressure variations between time domain and frequency domain. Free vibration analysis provides spatial distribution of impedance characteristics and pressure variation for determining optimum sensor location. A real-time filter can be designed to secure valid signals of any particular unsteady event. Hypothetical and experimental applications show that the proposed method has potentials of the leakage detection of a pipeline system as well as an efficient design of data acquisition system.

  11. Improving sustainability during hospital design and operation a multidisciplinary evaluation tool

    CERN Document Server

    Bottero, Marta; Buffoli, Maddalena; Lettieri, Emanuele

    2015-01-01

    This book describes the Sustainable High Quality Healthcare (SustHealth) project, which had the goal of developing an original multidisciplinary evaluation tool that can be applied to assess and improve hospitals’ overall sustainability. The comprehensive nature of the appraisal offered by this tool exceeds the scope of most current rating systems, which typically permit a thorough evaluation of relevant environmental factors when designing a new building but fail to consider social and economic impacts of the design phase or the performance of the hospital’s operational structure in these fields. The multidisciplinary evaluation system was developed, from its very inception through to its testing, by following a scientific experimental method in which a global perspective was constantly maintained, as opposed to a focus only on specific technical issues. Application of the SustHealth rating tool to a currently functioning hospital, or one under design, will identify weaknesses and guide users to potentia...

  12. Advanced operator interface design for CANDU-3 fuel handling system

    International Nuclear Information System (INIS)

    Arapakota, D.

    1995-01-01

    The Operator Interface for the CANDU 3 Fuel Handling (F/H) System incorporates several improvements over the existing designs. A functionally independent sit-down CRT (cathode-ray tube) based Control Console is provided for the Fuel Handling Operator in the Main Control Room. The Display System makes use of current technology and provides a user friendly operator interface. Regular and emergency control operations can be carried out from this control console. A stand-up control panel is provided as a back-up with limited functionality adequate to put the F/H System in a safe state in case of an unlikely non-availability of the Plant Display System or the F/H Control System'. The system design philosophy, hardware configuration and the advanced display system features are described in this paper The F/H Operator Interface System developed for CANDU 3 can be adapted to CANDU 9 as well as to the existing stations. (author)

  13. Advanced operator interface design for CANDU-3 fuel handling system

    Energy Technology Data Exchange (ETDEWEB)

    Arapakota, D [Atomic Energy of Canada Ltd., Saskatoon, SK (Canada)

    1996-12-31

    The Operator Interface for the CANDU 3 Fuel Handling (F/H) System incorporates several improvements over the existing designs. A functionally independent sit-down CRT (cathode-ray tube) based Control Console is provided for the Fuel Handling Operator in the Main Control Room. The Display System makes use of current technology and provides a user friendly operator interface. Regular and emergency control operations can be carried out from this control console. A stand-up control panel is provided as a back-up with limited functionality adequate to put the F/H System in a safe state in case of an unlikely non-availability of the Plant Display System or the F/H Control System`. The system design philosophy, hardware configuration and the advanced display system features are described in this paper The F/H Operator Interface System developed for CANDU 3 can be adapted to CANDU 9 as well as to the existing stations. (author).

  14. Operator Station Design System - A computer aided design approach to work station layout

    Science.gov (United States)

    Lewis, J. L.

    1979-01-01

    The Operator Station Design System is resident in NASA's Johnson Space Center Spacecraft Design Division Performance Laboratory. It includes stand-alone minicomputer hardware and Panel Layout Automated Interactive Design and Crew Station Assessment of Reach software. The data base consists of the Shuttle Transportation System Orbiter Crew Compartment (in part), the Orbiter payload bay and remote manipulator (in part), and various anthropometric populations. The system is utilized to provide panel layouts, assess reach and vision, determine interference and fit problems early in the design phase, study design applications as a function of anthropometric and mission requirements, and to accomplish conceptual design to support advanced study efforts.

  15. Smart home design and operation preferences of Americans and Koreans.

    Science.gov (United States)

    Jeong, Kyeong-Ah; Salvendy, Gavriel; Proctor, Robert W

    2010-05-01

    The purpose of the present study was to generate both culture-specific and universal design and operational guidelines for smart homes. Questionnaire surveys were performed in the USA and South Korea to collect data on preferences for various aspects of the design and operation of smart homes. The factors that the survey participants considered most important were derived through factor analyses of the survey data and the responses of Americans and Koreans were compared to generate culture-specific guidelines. The five factors derived were: 1) environmental connection and control; 2) smart devices (appliances) and their control; 3) physical safety and security concerns; 4) comfort and relaxation issues; 5) control restriction issues. The two cultures showed different preference structures with statistical significance for all five factors. Prediction capability of the derived factors was also examined through multiple regressions for buying intention, interest, self-vision of living, moving intention, living satisfaction and perceived time and effort savings. 'Environmental connection and control' and 'smart devices (appliances) and their control' seemed to be the most influential factors for Americans and Koreans, respectively. STATEMENT OF RELEVANCE: Analysis of a survey of design and operational preferences for smart homes yielded five factors on which US and South Korean respondents differed. These factors form the basis for culture-specific guidelines, which, along with universal guidelines, should be followed in design of user-centred smart homes.

  16. Design and operation of radioactive waste incineration facilities

    International Nuclear Information System (INIS)

    1992-01-01

    The purpose of this guide is to provide safety guidance for the design and operation of radioactive waste incineration facilities. The guide emphasizes the design objectives and system requirements to be met and provides recommendations for the procedure of process selection and equipment design and operation. It is recognized that some incinerators may handle only very low or 'insignificant' levels of radioactivity, and in such cases some requirements or recommendations of this guide may not fully apply. Nevertheless, it is expected that any non-compliance with the guide will be addressed and justified in the licensing process. It is also recognized that the regulatory body may place a limit on the level of the radioactivity of the waste to be incinerated at a specific installation. For the purpose of this guide an insignificant level of release of radioactivity may typically be defined as either the continuous or single event release of the design basis radionuclide inventory that represents a negligible risk to the population, the operating personnel, and/or the environment. The guidance on what constitutes a negligible risk and how to translate negligible risk or dose into level of activity can be found in Safety Series No. 89, IAEA, Vienna. 20 refs, 1 fig

  17. Issues at stake when considering long term storage of HLW. A comprehensive approach to designing the facility

    International Nuclear Information System (INIS)

    Marvy, A.; Ochem, D.

    2002-01-01

    CEA has been conducting a comprehensive R and D program to identify and study key HLW storage design criteria to possibly meet the lifetime goal of a century and beyond. A novel approach is being used since such installations must be understood as a global system comprised of various materials and hardware components, canisters, concrete and steel structures and specific procedures covering engineering steps from construction to operation including monitoring, care and maintenance as well as licensing. The challenge set by such a lifetime design goal made the R and D people focus on issues at stake and relevant to long term HLW storage in particular heat management, the effect of time on materials and the sustainability of care and maintenance. This opened up the R and D field from fundamental research areas to more conventional and technical aspects. Two major guiding principles have been devised as key design goals for the storage concepts under consideration. One is the paramount function of retrievability, which must allow the safe retrieval of any HLW package from the facility at any given time. Next is the passive containment philosophy requiring that a two-barrier system be considered. In the case of spent fuel, CEA's early assessment of the long-term behaviour of cladding shows that it cannot qualify as a reliable barrier over a long period of time. Therefore, the overriding strategy of preventing corrosion and material degradation to achieve canister protection, and therefore containment of radioactive material throughout the time of period envisaged, is at the heart of the R and D program and several design alternatives are being studied to meet that objective. For instance available thermal power from SF is used to establish dry corrosion conditions within the storage facility. The paper reviews all of these different R and D and engineering aspects. (author)

  18. Design improvements, construction and operating experience with BWRs in Japan

    International Nuclear Information System (INIS)

    Uchigasaki, G.; Yokomi, M.; Sasaki, M.; Aoki, R.; Hashimoto, H.

    1983-01-01

    (1) The first domestic-made 1100-MW(e) BWR in Japan commenced commercial operation in April 1982. The unit is the leading one of the subsequent three in Fukushima Daini nuclear power station owned by the Tokyo Electric Power Company Inc. (Tepco). Based on the accumulated construction and operation experience of 500-MW(e) and 800-MW(e) class BWRs, improvements in various aspects during both the design and construction stages were introduced in core and fuel design with advanced gadolinia distribution, reactor feedwater treatment technology for crud reduction, a radwaste island, control and instrumentation to cope with the lessons learned through Three Mile Island assessment etc. (2) Based on many operating experiences with BWRs, an improved BWR core, which has easier operability and higher load factor than the conventional core, has been developed. The characteristic of the improved core is ''axially two-zoned uranium enrichment distribution''; the enrichment of the upper part of the fuel is slightly higher than that of the lower part. Through the improved core it became possible to optimize the axial power flattening and core reactivity control separately by axial enrichment distribution and burnable poison content. The improved fuels were loaded into operating BWRs and successfully proved the performance by this experience. (3) To shorten annual outage time, to reduce radiation exposure, to save manpower, and to achieve high reliability and safety of inspection operation, the remote automatic service and inspection equipment were developed in Japan. This paper presents the concept, distinctive features, and actual operation experience of the automatic refuelling machine, control-rod drive (CRD) remote-handling machine, improved main steam line isolation plug, and the automated ultrasonic inspection system with a computerized data processing unit, which have been developed by Hitachi, Ltd. with excellent results. (author)

  19. Applying technology to operator requirements in medical equipment design.

    Science.gov (United States)

    Woodring, P L

    1986-01-01

    The methodology used by the author consists of the following elements: Expose the design team to the user environment, followed by question and answer periods with users while still in the use environment. Place biomedical engineers in the leading teaching institutions where they will have day-to-day exposure to the use of products similar to the one being designed. Bring biomedical engineers back into the company as part of the design team. Expose concepts to focus groups while the product is in the definition stage. Bring a select group of users into the design review process. Evaluate the ease of use of the device as part of clinical trials. Establish a means of monitoring product performance after the product has been released. How well such a methodology will work in any particular environment is a function of management's recognition of the concept that ease of operator use is a vital element to the overall success of the product.

  20. Operation Design of Wind Turbines in Strong Wind Conditions

    DEFF Research Database (Denmark)

    Shen, Wen Zhong; Montes, Melissa Barroso; Odgaard, Peter Fogh

    2012-01-01

    and variable speed pitch regulated wind turbines. The variable speed design is more suitable for wind turbines to run at very high wind speeds which can help the turbine braking system to stop the turbine at the new "cut-out" wind speed. Reference power, rotational speed and pitch angle have been designed...... optimally. In order to reduce the possible increased loading, fatigue due to the wind gusts, control strategies have been considered for both constant sped and variable speed pitch regulated wind turbines. The control study shows that the designed controllers can reduce the standard deviations efficiently......In order to reduce the impact on the electrical grid from the shutdown of MW wind turbines at wind speeds higher than the cut-out wind speed of 25 m/s, we propose in this paper to run the turbines at high wind speeds up to 40 m/s. Two different operation designs are made for both constant speed...

  1. Design of relative trajectories for in orbit proximity operations

    Science.gov (United States)

    Opromolla, Roberto; Fasano, Giancarmine; Rufino, Giancarlo; Grassi, Michele

    2018-04-01

    This paper presents an innovative approach to design relative trajectories suitable for close-proximity operations in orbit, by assigning high-level constraints regarding their stability, shape and orientation. Specifically, this work is relevant to space mission scenarios, e.g. formation flying, on-orbit servicing, and active debris removal, which involve either the presence of two spacecraft carrying out coordinated maneuvers, or a servicing/recovery spacecraft (chaser) performing monitoring, rendezvous and docking with respect to another space object (target). In the above-mentioned scenarios, an important aspect is the capability of reducing collision risks and of providing robust and accurate relative navigation solutions. To this aim, the proposed approach exploits a relative motion model relevant to two-satellite formations, and developed in mean orbit parameters, which takes the perturbation effect due to secular Earth oblateness, as well as the motion of the target along a small-eccentricity orbit, into account. This model is used to design trajectories which ensure safe relative motion, to minimize collision risks and relax control requirements, providing at the same time favorable conditions, in terms of target-chaser relative observation geometry for pose determination and relative navigation with passive or active electro-optical sensors on board the chaser. Specifically, three design strategies are proposed in the context of a space target monitoring scenario, considering as design cases both operational spacecraft and debris, characterized by highly variable shape, size and absolute rotational dynamics. The effectiveness of the proposed design approach in providing favorable observation conditions for target-chaser relative pose estimation is demonstrated within a simulation environment which reproduces the designed target-chaser relative trajectory, the operation of an active LIDAR installed on board the chaser, and pose estimation algorithms.

  2. A review on the sustainability of constructed wetlands for wastewater treatment: Design and operation.

    Science.gov (United States)

    Wu, Haiming; Zhang, Jian; Ngo, Huu Hao; Guo, Wenshan; Hu, Zhen; Liang, Shuang; Fan, Jinlin; Liu, Hai

    2015-01-01

    Constructed wetlands (CWs) have been used as a green technology to treat various wastewaters for several decades. CWs offer a land-intensive, low-energy, and less-operational-requirements alternative to conventional treatment systems, especially for small communities and remote locations. However, the sustainable operation and successful application of these systems remains a challenge. Hence, this paper aims to provide and inspire sustainable solutions for the performance and application of CWs by giving a comprehensive review of CWs' application and the recent development on their sustainable design and operation for wastewater treatment. Firstly, a brief summary on the definition, classification and application of current CWs was presented. The design parameters and operational conditions of CWs including plant species, substrate types, water depth, hydraulic load, hydraulic retention time and feeding mode related to the sustainable operation for wastewater treatments were then discussed. Lastly, future research on improving the stability and sustainability of CWs were highlighted. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Design of Packet-Based Block Codes with Shift Operators

    Directory of Open Access Journals (Sweden)

    Jacek Ilow

    2010-01-01

    Full Text Available This paper introduces packet-oriented block codes for the recovery of lost packets and the correction of an erroneous single packet. Specifically, a family of systematic codes is proposed, based on a Vandermonde matrix applied to a group of k information packets to construct r redundant packets, where the elements of the Vandermonde matrix are bit-level right arithmetic shift operators. The code design is applicable to packets of any size, provided that the packets within a block of k information packets are of uniform length. In order to decrease the overhead associated with packet padding using shift operators, non-Vandermonde matrices are also proposed for designing packet-oriented block codes. An efficient matrix inversion procedure for the off-line design of the decoding algorithm is presented to recover lost packets. The error correction capability of the design is investigated as well. The decoding algorithm, based on syndrome decoding, to correct a single erroneous packet in a group of n=k+r received packets is presented. The paper is equipped with examples of codes using different parameters. The code designs and their performance are tested using Monte Carlo simulations; the results obtained exhibit good agreement with the corresponding theoretical results.

  4. Design of Packet-Based Block Codes with Shift Operators

    Directory of Open Access Journals (Sweden)

    Ilow Jacek

    2010-01-01

    Full Text Available This paper introduces packet-oriented block codes for the recovery of lost packets and the correction of an erroneous single packet. Specifically, a family of systematic codes is proposed, based on a Vandermonde matrix applied to a group of information packets to construct redundant packets, where the elements of the Vandermonde matrix are bit-level right arithmetic shift operators. The code design is applicable to packets of any size, provided that the packets within a block of information packets are of uniform length. In order to decrease the overhead associated with packet padding using shift operators, non-Vandermonde matrices are also proposed for designing packet-oriented block codes. An efficient matrix inversion procedure for the off-line design of the decoding algorithm is presented to recover lost packets. The error correction capability of the design is investigated as well. The decoding algorithm, based on syndrome decoding, to correct a single erroneous packet in a group of received packets is presented. The paper is equipped with examples of codes using different parameters. The code designs and their performance are tested using Monte Carlo simulations; the results obtained exhibit good agreement with the corresponding theoretical results.

  5. Design basis programs and improvements in plant operation

    International Nuclear Information System (INIS)

    Metcalf, M.F.

    1991-01-01

    Public Service Electric and Gas (PSE and G) Company operates three commercial nuclear power plants in southern New Jersey. The three plants are of different designs and vintages (two pressurized water reactors licensed in 1976 and 1980 and one boiling water reactor licensed in 1986). As the industry recognized the need to develop design basis programs, PSE and G also realized the need after a voluntary 52-day shutdown of one unit because of electrical design basis problems. In its drive to be a premier electric utility, PSE and G has been aggressively active in developing design basis documents (DBDs) with supporting projects and refined uses to obtain the expected value and see the return on investment. Progress on Salem is nearly 75% complete, while Hope Creek is 20% complete. To data, PSE and G has experienced success in the use of DBDs in areas such as development of plant modifications, development of the reliability-centered maintenance program, procedure upgrades, improved document retrieval, resolution of regulatory issues, and training. The paper examines the design basis development process, supporting projects, and expected improvements in plant operations as a result of these efforts

  6. Microprocessors & their operating systems a comprehensive guide to 8, 16 & 32 bit hardware, assembly language & computer architecture

    CERN Document Server

    Holland, R C

    1989-01-01

    Provides a comprehensive guide to all of the major microprocessor families (8, 16 and 32 bit). The hardware aspects and software implications are described, giving the reader an overall understanding of microcomputer architectures. The internal processor operation of each microprocessor device is presented, followed by descriptions of the instruction set and applications for the device. Software considerations are expanded with descriptions and examples of the main high level programming languages (BASIC, Pascal and C). The book also includes detailed descriptions of the three main operatin

  7. Power electronics basics operating principles, design, formulas, and applications

    CERN Document Server

    Rozanov, Yuriy; Chaplygin, Evgeny; Voronin, Pavel

    2015-01-01

    Power Electronics Basics: Operating Principles, Design, Formulas, and Applications provides fundamental knowledge for the analysis and design of modern power electronic devices. This concise and user-friendly resource:Explains the basic concepts and most important terms of power electronicsDescribes the power assemblies, control, and passive components of semiconductor power switchesCovers the control of power electronic devices, from mathematical modeling to the analysis of the electrical processesAddresses pulse-width modulation, power quality control, and multilevel, modular, and multicell

  8. Design of a Power Tool Attachment for Sawing Operation

    Directory of Open Access Journals (Sweden)

    Mayur Appaiah

    2015-07-01

    Full Text Available The Design of a Power Tool Attachment for Sawing Operation is discussed. First, the Target Specifications are established. The Design work is carried out, especially that of the Main Shaft and Support Tube. Calculations and Finite Element Analysis (FEA are also done. The Prototype is fabricated and assembled. The Testing of the prototype is done, by Sawing commercial plywood of maximum thickness 25mm. Weight of the Attachment is 1.3 kg, and the Machine is easy to use, benefitting unskilled users.

  9. Optimal Design and Operation of Permanent Irrigation Systems

    Science.gov (United States)

    Oron, Gideon; Walker, Wynn R.

    1981-01-01

    Solid-set pressurized irrigation system design and operation are studied with optimization techniques to determine the minimum cost distribution system. The principle of the analysis is to divide the irrigation system into subunits in such a manner that the trade-offs among energy, piping, and equipment costs are selected at the minimum cost point. The optimization procedure involves a nonlinear, mixed integer approach capable of achieving a variety of optimal solutions leading to significant conclusions with regard to the design and operation of the system. Factors investigated include field geometry, the effect of the pressure head, consumptive use rates, a smaller flow rate in the pipe system, and outlet (sprinkler or emitter) discharge.

  10. Design of Omni Directional Remotely Operated Vehicle (ROV)

    Science.gov (United States)

    Rahimuddin; Hasan, Hasnawiya; Rivai, Haryanti A.; Iskandar, Yanu; Claudio, P.

    2018-02-01

    Nowadays, underwater activities are increased with the increase of oil resources finding. The gap between demand and supply of oil and gas cause engineers to find oil and gas resources in deep water. In other side, high risk of working in deep underwater environment can cause a dangerous situation for human. Therefore, many research activities are developing an underwater vehicle to replace the human’s work such as ROV or Remotely Operated Vehicles. The vehicle operated using tether to transport the signals and electric power from the surface vehicle. Arrangements of weight, buoyancy, and the propeller placements are significant aspect in designing the vehicle’s performance. This paper presents design concept of ROV for survey and observation the underwater objects with interaction vectored propellers used for vehicle’s motions.

  11. A discussion on turbine design for safe operation

    International Nuclear Information System (INIS)

    Brekke, H

    2012-01-01

    The paper gives a brief description of the hydraulic design of Francis and Pelton runners. The dynamic behaviour at part load has been a major problem for low head and medium head Francis turbines. The main reason for this has been inter blade separation and unstable swirl flow in the draft tube. A description is given on the hydraulic design of X-BLADE runners to obtain stable operation on the whole range of operation by reducing the cross flow. A classical theoretical analysis is also given on the dynamic hydraulic load on Pelton buckets. Several CFD analyses of this non stationary flow have been presented during the last decade, but the velocity distribution in the jets have not been correct. Experimental research work is presented on the complexity of this problem.

  12. Transferring Knowledge from Building Operation to Design: A literature review

    DEFF Research Database (Denmark)

    Rasmussen, Helle Lohmann; Jensen, Per Anker; Gregg, Jay Sterling

    . Knowing that the list lacks inputs from cultural and organizational theory, the paper suggests that further research should focus on taking these suggestions to an operational level for the benefit of FM, building clients and design teams. Furthermore, it is found that major concepts that could......As a solution to the previously identified gap between expected and actual building performance, this paper investigates how knowledge can be transferred from operation to design. This is assumed to help bridge the gap and increase the performance of new built facilities. By conducting a systematic...... literature review, it is found, that the theoretical approach in the reviewed articles has a significant impact on the level of how applicable the recommendations are in practice. Furthermore, a list of identified tools to enable knowledge transfer is provided, including POE, PPP and building commissioning...

  13. A discussion on turbine design for safe operation

    Science.gov (United States)

    Brekke, H.

    2012-11-01

    The paper gives a brief description of the hydraulic design of Francis and Pelton runners. The dynamic behaviour at part load has been a major problem for low head and medium head Francis turbines. The main reason for this has been inter blade separation and unstable swirl flow in the draft tube. A description is given on the hydraulic design of X-BLADE runners to obtain stable operation on the whole range of operation by reducing the cross flow. A classical theoretical analysis is also given on the dynamic hydraulic load on Pelton buckets. Several CFD analyses of this non stationary flow have been presented during the last decade, but the velocity distribution in the jets have not been correct. Experimental research work is presented on the complexity of this problem.

  14. Improved NGL recovery designs maximize operating flexibility and product recoveries

    International Nuclear Information System (INIS)

    Wilkinson, J.D.; Hudson, H.M.

    1992-01-01

    This paper reports that the historically cyclical nature in the market for ethane and propane has demonstrated the need for flexible natural gas liquids (NGL) recovery plants. NEwly developed and patented processes are now available which can provide ultra-high recovery of ethane (95%+) when demand for ethane is high and provide essentially complete ethane rejection without the normally concomitant reduction in propane recovery. This provides plant operators the flexibility to respond more readily to NGL market conditions, thus maximizing plant operating profits. The new process designs provide this flexibility without increasing utility requirements. In fact, utility consumption is often lower when compared to conventional designs. This same process technology can also be easily retrofit into existing plants with relatively quick payout of the modifications from both recovery and efficiency improvements

  15. GE-Hitachi ABWR Design for 60 Years of Operation

    International Nuclear Information System (INIS)

    Hoang Xuan Hoa

    2011-01-01

    The GE Hitachi ABWR design benefits from the experiences of the prior generation BWRs in operation since the 1970s, and the knowledge learned from years of technical research on the aging effects on reactor systems, structures and components. The impact of exposure to neutrons over time to the reactor pressure vessel and internal components was evaluated to confirm their structural integrity. Other time-based plant analyses, such as fatigue vibration and corrosion effect, have also been performed on the ABWR to support a 60-year plant life assumption. Finally, operating experience and aging lessons learned have been used to verify the maintenance plans for plant aging management are acceptable to support operation up to 60 years. (author)

  16. Designing and operating infrastructure for nonstationary flood risk management

    Science.gov (United States)

    Doss-Gollin, J.; Farnham, D. J.; Lall, U.

    2017-12-01

    Climate exhibits organized low-frequency and regime-like variability at multiple time scales, causing the risk associated with climate extremes such as floods and droughts to vary in time. Despite broad recognition of this nonstationarity, there has been little theoretical development of ideas for the design and operation of infrastructure considering the regime structure of such changes and their potential predictability. We use paleo streamflow reconstructions to illustrate an approach to the design and operation of infrastructure to address nonstationary flood and drought risk. Specifically, we consider the tradeoff between flood control and conservation storage, and develop design and operation principles for allocating these storage volumes considering both a m-year project planning period and a n-year historical sampling record. As n increases, the potential uncertainty in probabilistic estimates of the return periods associated with the T-year extreme event decreases. As the duration m of the future operation period decreases, the uncertainty associated with the occurrence of the T-year event also increases. Finally, given the quasi-periodic nature of the system it may be possible to offer probabilistic predictions of the conditions in the m-year future period, especially if m is small. In the context of such predictions, one can consider that a m-year prediction may have lower bias, but higher variance, than would be associated with using a stationary estimate from the preceding n years. This bias-variance trade-off, and the potential for considering risk management for multiple values of m, provides an interesting system design challenge. We use wavelet-based simulation models in a Bayesian framework to estimate these biases and uncertainty distributions and devise a risk-optimized decision rule for the allocation of flood and conservation storage. The associated theoretical development also provides a methodology for the sizing of storage for new

  17. Operating experience and design criteria of sodium valves

    International Nuclear Information System (INIS)

    Markford, D.

    1974-01-01

    The information presented refers to sodium valve development for KNK and SNR-300 as well as for sodium test facilities on the INTERATOM site at Bensberg. Well in advance of KNK-I a number of sodium test facilities have been operated containing small and medium size valves of different design and manufacturer. The more stringent requirements for long range safe and reliable operation in KNK-I put forth a development program for the main primary and secondary circuit sodium valves. Operational experience gave rise to modification of the stem seal arrangement mainly, so KNK-II (which is the fast core for KNK reactor) will be run with modified sodium valves. Main pipe diameters in SNR-300 are in the range of 600 mm. Valve designs with rising shafts would require excessive space in the primary circuit cavities, therefore efforts have been directed towards introduction of different type valves. Due to the requirements of after-heat-removal a valve type with control capability had to be chosen. A special design of butterfly valves was selected for the primary and secondary circuits of SNR-300. The development and tests performed with this type of valve are described. In the field of small sodium valves, tests with a 50 mm diameter freeze-seal valve are reported, and the current status of bellows-seal-valves to be inserted into SNR-300 is discussed. (U.S.)

  18. Design Knowledge and Design Change Management in the Operation of Nuclear Fleets

    International Nuclear Information System (INIS)

    Pelin, H.

    2016-01-01

    Full text: The operating lifetime of a nuclear plant spans several decades. During this time, the plant may undergo design changes resulting from experience feedback, new knowledge or requirements, and safety reviews. To ensure that safety remains optimized, these changes must be carried out with a full understanding of and without compromising the design intent. The licensee holds prime responsibility for the safety of the plant, and fully responsible for design change management. It fulfils this responsibility by establishing a formal system for ensuring the safety of the plant design throughout its lifetime, which includes establishing a formally designated entity within its management system, referred to as the Design Authority. The establishment of a Design Authority may be challenging for many operators. Therefore the licensee may allocate tasks to external organizations—the original designers—that have a specialized knowledge of specific parts of the plant, including vendors and equipment suppliers. Utilities operating plants of similar design should take advantage of this similarity to manage their knowledge through an international fleet-wide approach, facilitating sharing of experience and enabling similar solutions to be adopted for design changes. Opportunities for exchanges brought by owners’ groups, and other operators’ groups should be fully developed. (author

  19. Nuclear Design Study for Reduced Boron Concentration Operation

    International Nuclear Information System (INIS)

    Daing, Aung Tharn; Kim, Myung Hyun

    2008-01-01

    In PWR, Boron Dilution Accident (BDA) which is an inadvertent reduction of the soluble boron concentration in the primary coolant, can lead to a positive reactivity insertion and a power increase. In this study, an optimal Low Boron Concentration (LBC) core design will be developed by reducing an excess reactivity so as to possess passive inherently safety features as well as one of attentively preventive measures of BDA scenarios. The scope of the research project concerning the change of operational procedure in chemical shim system, will involve three main parts namely, nuclear design for LBC core, feasibility check on the proposed core in safety and costs, and PSA approach on design change benefits. In addition, successful system analysis of the reactivity effects due to boron dilution transients, require a full coupling between core thermal hydraulic, reactor dynamics, and the use of Computational Fluid Dynamics (CFD) codes

  20. Nuclear Design Study for Reduced Boron Concentration Operation

    Energy Technology Data Exchange (ETDEWEB)

    Daing, Aung Tharn; Kim, Myung Hyun [Kyung Hee University, Yongin (Korea, Republic of)

    2008-10-15

    In PWR, Boron Dilution Accident (BDA) which is an inadvertent reduction of the soluble boron concentration in the primary coolant, can lead to a positive reactivity insertion and a power increase. In this study, an optimal Low Boron Concentration (LBC) core design will be developed by reducing an excess reactivity so as to possess passive inherently safety features as well as one of attentively preventive measures of BDA scenarios. The scope of the research project concerning the change of operational procedure in chemical shim system, will involve three main parts namely, nuclear design for LBC core, feasibility check on the proposed core in safety and costs, and PSA approach on design change benefits. In addition, successful system analysis of the reactivity effects due to boron dilution transients, require a full coupling between core thermal hydraulic, reactor dynamics, and the use of Computational Fluid Dynamics (CFD) codes.

  1. Verification of design rules for EUROFER under TBM operating conditions

    International Nuclear Information System (INIS)

    Sunyk, R.; Aktaa, J.

    2007-01-01

    The aim of the activity presented in this work is, firstly, an evaluation of existing design rules considered for austenitic steels exhibiting cycle-by-cycle hardening, in contrast to the reduced-activation ferritic-martensitic steels (RAFM), which soften under cyclic loading. Secondly, we are aimed in a definition of the range of operating temperatures and loads for the current design of the test blanket module (TBM). Results of cycling tests of the EUROFER 97 have been thereby used to adjust material parameters needed for an ABAQUS-own combined non-linear isotropic-kinematic hardening model. Furthermore, a visco-plastic material model considering material damage and implemented recently as an ABAQUS user material (UMAT) has been also applied for simulations. Some important design rules within the elastic route have been evaluated and their predictions have been compared to results of cyclic simulations using the advanced material models mentioned above

  2. Design and Operation of 3-Pin FTL HVAC System

    International Nuclear Information System (INIS)

    Chi, D. Y.; Sim, B. S.; Park, S. K.; Park, K. N.; Lee, J. M.; Ahn, S. H.; Lee, C. Y.; Kim, Y. J.

    2005-01-01

    According to the increasing demand for irradiation tests to develop new fuels, the 3-Pin FTL(Fuel Test Loop for 3 pin test fuel) facility has now been under design to conduct in-core fuel performance tests at the operating conditions, which will be installed at HANARO. The HVAC system of the FTL will be dependent on that of the HANARO. The FTL has three equipments rooms, which are the room 1, room 2 and the control room. The high pressure and high temperature equipments will be installed in the room 1. The atmosphere of the room 1 shall be maintained under the designed condition. This paper describes the design of the FTL HVAC system in the room 1

  3. Preliminary design implications of SSC fixed-target operation

    International Nuclear Information System (INIS)

    Zisman, M.S.

    1984-06-01

    This paper covers some of the accelerator physics issues relevant to a possible fixed-target operating mode for the Superconducting Super Collider (SSC). In the brief time available, no attempt has been made to design this capability into the SSC. Rather, I have tried to evaluate what the performance of such a machine might be, and to indicate the hardware implications and extraction considerations that would be part of an actual design study. Where appropriate, parameters and properties of the present LBL design for the SSC have been used; these should be taken as being representative of the general class of small-aperture, high-field colliders being considered by the accelerator physics community. Thus, the numerical examples given here must ultimately be reexamined in light of the actual parameters of the particular accelerator being considered

  4. Designing and psychoanalysis: A comprehensive questionnaire on coping with domestic violence against women in Iranian society.

    Science.gov (United States)

    Mohhamadian, Zeinab; Mohtashami, Jamileh; Rohani, Camelia; Jamshidi, Tayebeh

    2018-01-01

    Domestic violence is the third sociopathology after addiction and child abuse in Iran. Fifty-six percent of Iranian women in the range of 17-32 years old are exposed to the highest domestic violence. Objective: The aim of this study was to design and psychoanalyze a comprehensive questionnaire on coping with domestic violence against women in Iranian society. This study was carried out on a random sample of women exposed to domestic violence and referred to the health and care center of Shahid Beheshti University of Medical Sciences in Tehran, and Forensic Medical Centers in Urmia city (Iran), in 2017. Two hundred questionnaires were distributed among the participants. One hundred sixty-eight questionnaires were returned to the researchers for data analysis. Eight of those were excluded from the analysis because of incompleteness. Finally, exploratory factor analysis was performed. After reviewing the literature, a questionnaire with 32 items was developed. Content validity ratio (0.95) and content validity index (0.97) were obtained. The results of exploratory factor analysis indicated that the questionnaire explained 69.34% of the data variance. Cronbach's alpha coefficient, and test-retest methods were used for determining the reliability and the obtained value, which were 0.82 and 0.81, respectively. Validity and reliability of the questionnaire with 32 items were confirmed. The tool can be utilized to measure how women cope with domestic violence.

  5. Role of cognitive models of operators in the design, operation and licensing of nuclear power plants

    International Nuclear Information System (INIS)

    Rasmussen, J.

    1982-01-01

    Cognitive models of the behavior of nuclear power plant operators - that is, models developed in terms of human properties rather than external task characteristics - are assuming increasingly important roles in plant design, operation and licensing. This is partly due to an increased concern for human decision making during unfamiliar plant conditions, and partly due to problems that arise when modern information technology is used to support operators in complex situations. Some of the problems identified during work on interface design and risk analysis are described. First, the question of categories of models is raised. Next, the use of cognitive models for system design is discussed. The use of the available cognitive models for more effective operator training is also advocated. The need for using cognitive models in risk analysis is also emphasized. Finally, the sources of human performance data, that is, event reports, incident analysis, experiments, and training simulators are mentioned, and the need for a consistent framework for data analysis based on cognitive models is discussed

  6. Structured tradeoffs preference elicitation: Evaluating CRWMS design and operations

    International Nuclear Information System (INIS)

    Hartman, H.

    1994-01-01

    Preliminary studies over the past few years have yielded multiple design and operations alternatives for the planned Civilian Radioactive Waste Management System (CRWMS). Waste isolation, pre-closure health and safety, and life cycle cost are among the many factors considered in developing these alternatives. The task of CRWMS designers is complicated by substantial heat and nuclear radiation energy output of the spent nuclear fuel and high level waste intended for disposal in an underground repository. Not only must the usual effectiveness, operability and cost objectives be balanced, but done so in the context of a constantly changing environment. Particular alternatives sometimes are favored by virtue of their outstanding performance relative to one of these factors. The Ultimate success of the potential repository, however, depends on reaching a defensible and traceable final decision through simultaneous and systematic weighing of all relevant factors. This paper documents the outcome of Structured Tradeoffs Preference (STP) elicitation as a method for the simultaneous and systematic weighing of factors relevant to repository thermal loading, waste package (WP) design, and emplacement mode decisions. The study provided a low-cost early indication of directions of further research on CRWMS design and operations likely to be most fruitful. The method of STP elicitation was utilized to avoid potential biases documented in other efforts which use only unstructured decision making, or open-quotes well-considered judgmentclose quotes. The STP elicitation procedure presented here complements the use of a parameter network-model pyramid suggested elsewhere in this proceedings to provide a framework for precisely articulating technical questions needing answers. It also forms an independent crosscheck of systems engineering study results and performance assessment modeling

  7. Information management system for design, construction and operation of nuclear power plants

    International Nuclear Information System (INIS)

    Bolch, M.C.; Jones, C.R.

    1990-01-01

    This paper describes the principal requirements and features of a computerized information management system (IMS) believed to be a necessary part of the program to design, build and operate the next generation of nuclear power plants in the United States. This way a result of extensive review and input from an industry group studying future nuclear power plant construction improvements. The needs of the power plant constructor, owner and operator for such a computerized technical data base are described in terms of applications and scope and timing of turnover of the IMS by the plant designer. The applications cover the full life cycle of the plant including project control, construction activities, quality control, maintenance and operation. The scope of the IMS is also described in terms of the technical data to be included, hardware and software capabilities and training. The responsibilities of the plant designer for developing the IMS and generating the technical data base is defined as part of the plant process. The requirements to be met include a comprehensive plant data model and computer system hardware and software

  8. Information management system for design, construction and operation of nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Bolch, M.C. (Duke Power Co. (US)); Jones, C.R. (S. Levy Inc. (US))

    1990-01-01

    This paper describes the principal requirements and features of a computerized information management system (IMS) believed to be a necessary part of the program to design, build and operate the next generation of nuclear power plants in the United States. This way a result of extensive review and input from an industry group studying future nuclear power plant construction improvements. The needs of the power plant constructor, owner and operator for such a computerized technical data base are described in terms of applications and scope and timing of turnover of the IMS by the plant designer. The applications cover the full life cycle of the plant including project control, construction activities, quality control, maintenance and operation. The scope of the IMS is also described in terms of the technical data to be included, hardware and software capabilities and training. The responsibilities of the plant designer for developing the IMS and generating the technical data base is defined as part of the plant process. The requirements to be met include a comprehensive plant data model and computer system hardware and software.

  9. Design and operation of the Surry Radwaste Facility

    International Nuclear Information System (INIS)

    Morris, L.L.; Halverson, W.C.

    1993-01-01

    In September 1991, Virginia Power started processing radioactive waste with a new Radwaste Facility at the Surry Power Station near Norfolk, Virginia. The Surry Radwaste Facility (SRF) was designed to process and store liquid waste, laundry waste, dry active waste, radioactive filters and spent ion-exchange resin. It also provides on-site decontamination services and a fully equipped hot machine shop. The NRC has recognized that the amount of planning and design, and the attention to detail, that was expended on the SRF Project in order to minimize personnel exposure and ensure efficient operation, is a licensee strength. Through its first year of operation, the facility has proven very successful. Using evaporation and demineralization, over 30 million liters of liquid have been released with no chemical impurities or detectable radioactivity (excluding tritium). Over 623,000 liters of concentrated boric acid waste liquid have been processed with the Bitumen Solidification System yielding 139,880 liters (660 drums) of low level Class A-Stable waste. Additional economic benefits will be realized as the effectiveness of the processing systems continues to improve due to increased operational experience and ergonomics

  10. A comprehensive study of the characterization of particulate matter emissions from a Delmarva broiler poultry operation

    Science.gov (United States)

    Carter, Shannon E.

    Particulate matter (PM) emissions from agricultural practices, including those from animal feeding operations (AFO's) have become an increasingly important topic, and has generated considerable interest from local and state agencies, as well as, the local community over the past decade. Because of growth in population, and an increase in commercial and residential development within close proximity to these operations, which house a large number of animals in confinement, and because of a better understanding of the effects of exposure to airborne contaminants on health, this has lead to an increase in concerns and a demand for more research to be conducted on PM from AFO's. Particulate matter generated within, and emitted from, AFO's can carry with it various components including metals and microorganisms that can negatively affect health. This research was conducted in order to verify if PM from a broiler poultry operation on Delmarva has the potential to become a health concern. The first step was to determine concentrations of two size segregated fractions of PM from indoor and outdoor sampling sites over four seasonal periods, early summer (ES), late summer (LS), Fall (F), and Winter (W). Both PM10 and PM2.5 were collected because of their classification from the Environmental Protection Agency as having the ability to cause significant health effects with short-term exposure. Next, temporal and spatial characteristics were investigated to determine their effects on PM concentrations over the four seasonal periods. Following this, the chemical composition and morphology of PM10 and PM2.5 generated from the broiler poultry operation was investigated. Finally, further detailed information was obtained on arsenic speciation and oxidation state in PM to investigate toxicity. Arsenic use in the poultry industry has been occurring for a number of decades, and is most frequently administered in the organic form. However, studies have shown that these organo

  11. Design and operation of liquid-liquid extractors

    International Nuclear Information System (INIS)

    Wangquian Zhao.

    1996-01-01

    The performance of liquid-liquid extraction columns, with regard to design and operation, has been theoretically and experimentally studied in this work. Under the assumption of plug flow conditions, simple models for both differential and stagewise columns have been developed to establish quantitative relationships between the variables involved for the purpose of the prediction of extraction column performance. Although both models were developed at the beginning of the century, the analytical solutions are available only for the case of linear equilibria. This restriction is relaxed in this work by deriving analytical solutions for the case of curved equilibria. Two reliable models, namely the diffusion and backflow models, which allow for the effect of axial mixing on mass transfer, are available. Under the assumption of constant parameters, the analytical solutions of both models can be obtained. However, these analytical solutions for both models have complex form and are difficult to use in design since iterative solutions are required. To overcome this difficulty, approximate design equations with acceptable accuracy for both models are presented in this work which enable column height or the number of real stages to be obtained directly from specified separation, operating conditions, mass transfer and eddy diffusion coefficients and system properties. The proposed design equations are simple and suitable for manual calculation. They are preferable to previous simplified methods and purely empirical methods. The analytical solutions are restricted to constant parameters and simple linear equilibrium relationship. In order to design columns more accurately and to predict their performance more confidently, the axial variations of parameters and nonlinear relationship must be taken into account. In this work, a mathematical model based on population balance equation is formulated for the prediction of variations of drop size and holdup along the column

  12. Synthetic viewing: Comprehensive work representation making remote work more transparent to the operator

    International Nuclear Information System (INIS)

    Leinemann, K.; Katz, F.; Knueppel, H.

    1994-01-01

    To support the operator remote handling a number of well-developed techniques is available like transmission of forces, movements, and dexterous skills in general using masterslave manipulators equipped with special tools. In addition several types of transporters are available to position manipulators and tools. But there is a serious bottle-neck in viewing: the number of cameras is restricted and the cameras may in most cases not be positioned as to provide sufficient information. In order to improve this situation an integration of closed-loop TV and artificial viewing by sensor controlled computer graphics has been introduced successfully by KfK at JET. This integrated viewing subsystem combines not only those two techniques by providing the two views but also enhances the conventional camera control by a computer graphics model-based control. Practical experience has shown that the concept of viewing needs to be extended. Just seeing where things are is insufficient for the operators to perform their remote handling task properly. More information is required about the status of all equipment pieces involved and about the status of the entire handling task. Viewing for remote handling applications needs to include the display of such status information in a suitable form

  13. Synthetic viewing: comprehensive work representation, making remote work clearer to the operator

    International Nuclear Information System (INIS)

    Leinemann, K.; Katz, F.; Knueppel, H.; Olbrich, W.; Maisonnier, D.

    1995-01-01

    Maintenance work in fusion plants such as the ITER plant will be carried out fully remotely, without any direct view on to the work scene. The basic sources of information about the state of the work are video monitors. In a first development step, this viewing channel was enhanced by three-dimensional computer graphics controlled by signals of motion sensors (such as joint angle sensors) of the real maintenance devices. However, experience has shown that more information is required about the status of all pieces of equipment involved and about the status of the entire handling task, if the work is to be done properly. Viewing for remote handling applications needs to include the display of such status information in a suitable form. Of special importance in this sense is the representation of the work procedures on the computer display, enabling the operator to grasp at a glance the actual state of the work and the details about the subtask to be executed next. The tool providing this ''synthetic'' viewing but also task-suited to planning, training and controlling support for the operator is the remote handling workstation. The prototype of a remote handling workstation was successfully used in the first complete Karlsruhe experiment for in-torus handling. (orig.)

  14. XMM-Newton operations beyond the design lifetime

    Science.gov (United States)

    Parmar, Arvind N.; Kirsch, Marcus G. F.; Muñoz, J. Ramon; Santos-Lleo, Maria; Schartel, Norbert

    2012-09-01

    After more than twelve years in orbit and two years beyond the design lifetime, XMM-Newton continues its near faultless operations providing the worldwide astronomical community with an unprecedented combination of imaging and spectroscopic X-ray capabilities together with simultaneous optical and ultra-violet monitoring. The interest from the scientific community in observing with XMM-Newton remains extremely high with the last annual Announcement of Observing Opportunity (AO-11) attracting proposals requesting 6.7 times more observing time than was available. Following recovery from a communications problem in 2008, all elements of the mission are stable and largely trouble free. The operational lifetime if currently limited by the amount of available hydrazine fuel. XMM-Newton normally uses reaction wheels for attitude control and fuel is only used when offsetting reaction wheel speed away from limiting values and for emergency Sun acquisition following an anomaly. Currently, the hydrazine is predicted to last until around 2020. However, ESA is investigating the possibility of making changes to the operations concept and the onboard software that would enable lower fuel consumption. This could allow operations to well beyond 2026.

  15. Conceptual design of autonomous operation system for nuclear power plants

    International Nuclear Information System (INIS)

    Endou, A.; Saiki, A.; Miki, T.; Himeno, Y.

    1993-01-01

    Conceptual design of an autonomous operation system for nuclear power plants has been carried out. Prime objective is to grade up operation reliability by eliminating human factors and enhancing control capabilities. For this objective, operators' role and traditional controllers are replaced with artificial intelligence (AI). Norms of autonomy are defined as (a) to maintain its own basic functions, (b) to protect oneself from catastrophic events, (c) to reorganize oneself in case of its partial failure, (d) to harmonize with the environment, and (e) to improve its performance by itself. For the present, a great emphasis is put on realizing humanlike knowledge-based decision-making process by AI in accordance with the norms (a) and (c). To do this, the authors take a model-based approach and it is intended to make modeling of a problem-solving process from multiple viewpoints and structurization of knowledge used in the process. A hierarchical distributed cooperative system configuration is adopted to allow to dynamically reorganize system functions and it is realized by an object-oriented multi-agent system. Plural agents based on different methodology from each other are applied to individual function or methodology diversity is assured to prevent loss of system functions by common cause failure and to reorganize integrant agents. A prototype autonomous operation system is now under development. (orig.)

  16. Enhancement of pressurizer safety valve operability by seating design improvement

    International Nuclear Information System (INIS)

    Moisidis, N.T.; Ratiu, M.D.

    1995-01-01

    Operating conditions specific to pressurizer safety valves (PSVs) have led to numerous problems and have caused industry and NRC concerns regarding the adequacy of spring-loaded self-actuated safety valves for reactor coolant system (RCS) overpressure protection. Specific concerns are: setpoint drift, spurious actuations, and pressure protection. Specific concerns are: setpoint drift, spurious actuations, and leakage. Based on testing and valve construction analysis of a Crosby model 6M6 PSV (Moisidis and Ratiu, 1992), it was established that the primary contributor to the valve problems is a susceptibility to weak seating. To eliminate spring instability, a new spring washer was designed, which guides the spring and precludes its rotation from the reference installed position. Results of tests performed on a prototype PSV equipped with the modified upper spring washer has shown significant improvements in valve operability and a consistent setpoint reproducibility to less than ±1% of the PSV setpoint (testing of baseline, unmodified valve, resulted in a setpoint drift of ± 2%). Enhanced valve operability will result in a significant decrease in operating and maintenance costs associated with valve maintenance and testing. In addition, the enhanced setpoint reproducibility will allow the development of a nitrogen to steam correlation for future in-house PSV testing which will result in further reductions in costs associated with valve testing

  17. Enhancement of pressurizer safety valve operability by seating design improvement

    International Nuclear Information System (INIS)

    Moisidis, N.T.; Ratiu, M.D.

    1994-01-01

    Operating conditions specific to Pressurizer Safety Valves (PSVs) have led to numerous problems and have caused industry and NRC concerns regarding the adequacy of spring loaded self-actuated safety valves for Reactor Coolant System (RCS) overpressure protection. Specific concerns are: setpoint drift, spurious actuations and leakage. Based on testing and valve construction analysis of a Crosby model 6M6 PSV, it was established that the primary contributor to the valve problems is a susceptibility to weak seating. To eliminate spring instability, a new spring washer was designed, which guides the spring and precludes its rotation from the reference installed position. Results of tests performed on a prototype PSV equipped with the modified upper spring washer has shown significant improvements in valve operability and a consistent setpoint reproducibility to less than ±1% of the PSV setpoint (testing of baseline, unmodified valve, resulted in a setpoint drift of ±2%). Enhanced valve operability will result in a significant decrease in operating and maintenance costs associated with valve maintenance and testing. In addition, the enhanced setpoint reproducibility will allow the development of a nitrogen to steam correlation for future in-house PSV testing which will result in further reductions in costs associated with valve testing

  18. A knowledge-centered paradigm for operations and design

    International Nuclear Information System (INIS)

    Perin, C.

    2005-01-01

    A paradigm premised on the reactor design basis and on its systems, structures, and components also governs nuclear power plant operations. This machine-centered paradigm emphasizes a functional and discipline-based division of responsibilities, which can create hierarchical 'silos' and 'stovepipes' inhibiting the development and lateral exchange of knowledge about safety-critical system interactions. A knowledge-centered paradigm instead encourages the timely development, analysis, and exchange of information about system conditions and their likely consequences. This new paradigm puts operational focus on the importance of operating experience, informative root cause analyses, effective corrective actions, and cross-discipline exchange and cooperation. Although the knowledge-centered paradigm is already central to three main strategies of risk reduction, it is less likely to be recognized as such in terms of priorities, resources, and training: configuration control, control room operations, and root cause analysis. To maintain the capacity for safe shutdown and to preserve public trust, the knowledge-centered paradigm places as high a priority on interactions of safety-critical knowledge as it does on interactions of safety-critical systems, structures, and components. (author)

  19. Design requirements, operation and maintenance of gas-cooled reactors

    International Nuclear Information System (INIS)

    1989-06-01

    At the invitation of the Government of the USA the Technical Committee Meeting on Design Requirements, Operation and Maintenance of Gas-Cooled Reactors, was held in San Diego on September 21-23, 1988, in tandem with the GCRA Conference. Both meetings attracted a large contingent of foreign participants. Approximately 100 delegates from 18 different countries participated in the Technical Committee meeting. The meeting was divided into three sessions: Gas-cooled reactor user requirement (8 papers); Gas-cooled reactor improvements to facilitate operation and maintenance (10 papers) and Safety, environmental impacts and waste disposal (5 papers). A separate abstract was prepared for each of these 23 papers. Refs, figs and tabs

  20. Design, commissioning and operation of the Swiss Light Source SLS

    International Nuclear Information System (INIS)

    Streun, Andreas

    2003-01-01

    The Swiss Light Source (SLS) at the Paul Scherrer Institute (PSI) is the most recent 3rd generation light source coming to operation. It consists of a 12- TBA storage ring of 288 m circumference providing 5 nm rad emittance at 2.4 GeV, a novel type of full energy booster synchrotron and a 100 MeV linac. The initial four beamlines cover protein X-ray crystallography (PX), materials science (MS), surface and interface spectroscopy (SIS) and microscopy (SIM). We will review the project history, describe the design concepts of the accelerators and the technical subsystems, and report on the commissioning process and the status of operation by end of 2002. (author)

  1. Design of a Comprehensive Biochemistry and Molecular Biology Experiment: Phase Variation Caused by Recombinational Regulation of Bacterial Gene Expression

    Science.gov (United States)

    Sheng, Xiumei; Xu, Shungao; Lu, Renyun; Isaac, Dadzie; Zhang, Xueyi; Zhang, Haifang; Wang, Huifang; Qiao, Zheng; Huang, Xinxiang

    2014-01-01

    Scientific experiments are indispensable parts of Biochemistry and Molecular Biology. In this study, a comprehensive Biochemistry and Molecular Biology experiment about "Salmonella enterica" serovar Typhi Flagellar phase variation has been designed. It consisted of three parts, namely, inducement of bacterial Flagellar phase variation,…

  2. Membrane Bioreactors design and operation improvements: The Spanish Experience

    International Nuclear Information System (INIS)

    Iglesias Esteban, R.; Ortega de Miguel, E.; Martinez Tarifa, M. A.; Simon Andreu, P.; Moragas Bouyart, L.; Garcia Fernandez, E.; Robuste Cartro, J.; Rodriguez-Roda layret, I.

    2012-01-01

    A Membrane Bioreactor (MBR) is a modification of a conventional activated sludge (CAS) plant where the secondary settling ins replaced by a low pressure ultrafiltration (UF) or micro filtration (MF) membranes separation process in order to obtain an effluent almost free of suspended solids and microorganisms. since the first MBR installation in 2002, the number and capacity of these systems have exponentially increased in spain, driven by the high quality of the effluent which allows direct reuse and discharge into environmentally sensitive areas, the compactness and automation of these plants and the possibility of upgrading existing wastewater treatment plants (WWTP) which no longer reach the required effluent quality levels. There were 45 operating MBR systems in 2011 and the total municipal wastewater treatment capacity by this type of plants will be about 90 hm 3 in 204 when the current projects have been implemented. Today, Spain public and private wastewater management agencies consider MBR plants as an alternative of treatment but first they had to face a complex learning period to operate and design this kind of system. A significant progress has been made over the last years, but especially energy efficiency responds to the challenge of continuous improvement. Membrane fouling control consumes most of the energy involved in the process therefore, anti fouling materials and better membrane air-scour systems that allow the frequency and intensity of air flow to be controlled in realtime, are being investigated. This brings MBR closer to the CAS process in terms of energy efficiency. Breakthroughs in the design and operation of MBR plants are being collected in a guide for the implementation of MBR led by CEDEX, in which the main managers and operators are involved. This paper presents some of these improvements. (Author) 9 refs.

  3. Efficacy, complications, and cost of a comprehensive blood conservation program for cardiac operations.

    Science.gov (United States)

    Scott, W J; Rode, R; Castlemain, B; Kessler, R; Follis, F; Pett, S B; Wernly, J A

    1992-05-01

    We reviewed blood use in 118 consecutive patients who underwent primary, elective cardiac operations in 1989. In June 1989 we initiated a blood conservation program that included attempts to limit preoperative aspirin use, intraoperative phlebotomy and hemodilution, use of a cell conservation device (Electromedics, Inc., Englewood, Colo.) to concentrate residual oxygenator contents, reinfusion of chest drainage, and acceptance of a minimum hemoglobin level of 8.0 gm/dl in stable patients. Patient characteristics were similar for patients operated on both before (n = 58) and after (n = 60) initiation of the blood conservation program, except for age and preoperative aspirin use (both greater in postconservation patients). Fewer blood products were transfused (5.8 +/- 5.7 units per patient before conservation versus 4.0 +/- 7.4 units per patient after conservation; p = 0.005). More complete data were available for 82 patients (40 patients before conservation and 42 after conservation). In the postconservation patients, 20 of 42 had 575 +/- 140 ml of blood withdrawn before cardiopulmonary bypass and reinfused afterward, 26 of 42 had 806 +/- 376 ml of blood processed with the cell conservation device returned, and 21 of 42 patients had an average of 287 +/- 127 ml of chest drainage reinfused. Chest tube drainage, postoperative hematologic parameters, and the prevalence of complications were not significantly different between groups. Stepwise linear regression analysis identified intraoperative withdrawal of blood before cardiopulmonary bypass, bypass duration, and preoperative hematocrit value as predictors of blood use. Intraoperative withdrawal of blood before cardiopulmonary bypass is an important conservation measure, and its use should be expanded.

  4. Framework for Integrating Safety, Operations, Security, and Safeguards in the Design and Operation of Nuclear Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Darby, John L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Horak, Karl Emanuel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); LaChance, Jeffrey L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Tolk, Keith Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Whitehead, Donnie Wayne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2007-10-01

    The US is currently on the brink of a nuclear renaissance that will result in near-term construction of new nuclear power plants. In addition, the Department of Energy’s (DOE) ambitious new Global Nuclear Energy Partnership (GNEP) program includes facilities for reprocessing spent nuclear fuel and reactors for transmuting safeguards material. The use of nuclear power and material has inherent safety, security, and safeguards (SSS) concerns that can impact the operation of the facilities. Recent concern over terrorist attacks and nuclear proliferation led to an increased emphasis on security and safeguard issues as well as the more traditional safety emphasis. To meet both domestic and international requirements, nuclear facilities include specific SSS measures that are identified and evaluated through the use of detailed analysis techniques. In the past, these individual assessments have not been integrated, which led to inefficient and costly design and operational requirements. This report provides a framework for a new paradigm where safety, operations, security, and safeguards (SOSS) are integrated into the design and operation of a new facility to decrease cost and increase effectiveness. Although the focus of this framework is on new nuclear facilities, most of the concepts could be applied to any new, high-risk facility.

  5. The HAL 9000 Space Operating System Real-Time Planning Engine Design and Operations Requirements

    Science.gov (United States)

    Stetson, Howard; Watson, Michael D.; Shaughnessy, Ray

    2012-01-01

    In support of future deep space manned missions, an autonomous/automated vehicle, providing crew autonomy and an autonomous response planning system, will be required due to the light time delays in communication. Vehicle capabilities as a whole must provide for tactical response to vehicle system failures and space environmental effects induced failures, for risk mitigation of permanent loss of communication with Earth, and for assured crew return capabilities. The complexity of human rated space systems and the limited crew sizes and crew skills mix drive the need for a robust autonomous capability on-board the vehicle. The HAL 9000 Space Operating System[2] designed for such missions and space craft includes the first distributed real-time planning / re-planning system. This paper will detail the software architecture of the multiple planning engine system, and the interface design for plan changes, approval and implementation that is performed autonomously. Operations scenarios will be defined for analysis of the planning engines operations and its requirements for nominal / off nominal activities. An assessment of the distributed realtime re-planning system, in the defined operations environment, will be provided as well as findings as it pertains to the vehicle, crew, and mission control requirements needed for implementation.

  6. Intrusion resistant underground structure (IRUS) : design and operations

    International Nuclear Information System (INIS)

    Lange, B.A.

    1997-01-01

    The safety case for the IRUS low-level radioactive waste disposal facility is based on the fact that IRUS will contain three specific types of wastes only. The types of these wastes are baled wastes, bituminized incinerator ash, and bituminized reverse osmosis concentrate. IRUS will be a below-ground vault consisting of an open bottom reinforced-concrete structure (approximate dimensions 30m x 20m x 8m) with a reinforced-concrete roof. This paper covers the vault design and construction and operational features. 2 tabs

  7. Design and operation of a thermionic converter in air

    International Nuclear Information System (INIS)

    Horner, M.H.; Begg, L.L.; Smith, J.N. Jr.; Geller, C.B.; Kallnowski, J.E.

    1995-01-01

    An electrically heated thermionic converter has been designed, built and successfully tested in air. Several unique features were incorporated in this converter: an integral cesium reservoir, innovative ceramic-to-metal seals, a heat rejection system coupling the collector to a low temperature heat sink and an innovative cylindrical heater filament. The converter was operated for extended periods of time with the emitter at about 1900 K. the collector at about 700 K, and a power density of over 2 w(e)/sq. cm. Input power transients were run between 50% and 100% thermal power, at up to 1% per second, without instabilities in performance

  8. Microfabricated thermal modulator for comprehensive two-dimensional micro gas chromatography: design, thermal modeling, and preliminary testing.

    Science.gov (United States)

    Kim, Sung-Jin; Reidy, Shaelah M; Block, Bruce P; Wise, Kensall D; Zellers, Edward T; Kurabayashi, Katsuo

    2010-07-07

    In comprehensive two-dimensional gas chromatography (GC x GC), a modulator is placed at the juncture between two separation columns to focus and re-inject eluting mixture components, thereby enhancing the resolution and the selectivity of analytes. As part of an effort to develop a microGC x microGC prototype, in this report we present the design, fabrication, thermal operation, and initial testing of a two-stage microscale thermal modulator (microTM). The microTM contains two sequential serpentine Pyrex-on-Si microchannels (stages) that cryogenically trap analytes eluting from the first-dimension column and thermally inject them into the second-dimension column in a rapid, programmable manner. For each modulation cycle (typically 5 s for cooling with refrigeration work of 200 J and 100 ms for heating at 10 W), the microTM is kept approximately at -50 degrees C by a solid-state thermoelectric cooling unit placed within a few tens of micrometres of the device, and heated to 250 degrees C at 2800 degrees C s(-1) by integrated resistive microheaters and then cooled back to -50 degrees C at 250 degrees C s(-1). Thermal crosstalk between the two stages is less than 9%. A lumped heat transfer model is used to analyze the device design with respect to the rates of heating and cooling, power dissipation, and inter-stage thermal crosstalk as a function of Pyrex-membrane thickness, air-gap depth, and stage separation distance. Experimental results are in agreement with trends predicted by the model. Preliminary tests using a conventional capillary column interfaced to the microTM demonstrate the capability for enhanced sensitivity and resolution as well as the modulation of a mixture of alkanes.

  9. Fuel element structure - design, production and operational behaviour

    International Nuclear Information System (INIS)

    Pott, G.; Dietz, W.

    1985-01-01

    The lectures held at the meeting of the fuel element section of the Kerntechnische Gesellschaft gives a survey of developments in fuel element structure design for PWR-type, BWR-type and fast breeder reactors. For better utilization of the fuel, concepts have been developed for re-usable, removable and thus repairable fuel elements. Furthermore, the manufacturing methods for fuel element structures were refined to achieve better quality and more efficient manufacturing methods. Statements on the dimensional behaviour and on the mechanical stability of fuel element structures in normal and accident operation could be made on the basis of post-irradiation inspections. Finally, the design, manufacture and irradiation behaviour of graphite reflectors in HTGR-type reactors are described. The 12 lectures have been recorded in the data base separately. (RF) [de

  10. Design of inventory pools in spare part support operation systems

    Science.gov (United States)

    Mo, Daniel Y.; Tseng, Mitchell M.; Cheung, Raymond K.

    2014-06-01

    The objective of a spare part support operation is to fulfill the part request order with different service contracts in the agreed response time. With this objective to achieve different service targets for multiple service contracts and the considerations of inventory investment, it is not only important to determine the inventory policy but also to design the structure of inventory pools and the order fulfilment strategies. In this research, we focused on two types of inventory pools: multiple inventory pool (MIP) and consolidated inventory pool (CIP). The idea of MIP is to maintain separated inventory pools based on the types of service contract, while CIP solely maintains a single inventory pool regardless of service contract. Our research aims to design the inventory pool analytically and propose reserve strategies to manage the order fulfilment risks in CIP. Mathematical models and simulation experiments would be applied for analysis and evaluation.

  11. Simulation of gas turbines operating in off-design condition

    Energy Technology Data Exchange (ETDEWEB)

    Walter, Arnaldo [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Energia]. E-mail: walter@fem.unicamp.br

    2000-07-01

    In many countries thermal power plants based on gas turbines have been the main option for new investment into the electric system due to their relatively high efficiency and low capital cost. Cogeneration systems based on gas turbines have also been an important option for the electric industry. Feasibility studies of power plants based on gas turbine should consider the effect of atmospheric conditions and part-load operation on the machine performance. Doing this, an off-design procedure is required. A G T off-design simulation procedure is described in this paper. Ruston R M was used to validate the simulation procedure that, general sense, presents deviations lower than 2.5% in comparison to manufacturer's data. (author)

  12. Design of the ITER magnets to provide plasma operational flexibility

    International Nuclear Information System (INIS)

    Mitchell, N.; Bessette, D.; Ferrari, M.; Huguet, M.; Jong, C.; Takahashi, Y.; Yoshida, K.; Maix, R.; Krivchenkov, Y.; Zapretilina, E.

    2005-01-01

    The ITER magnets have been optimised and refined since the ITER Final Design Report (FDR) in 2001. Multiple design options have been eliminated and there is improved ability to drive a wide range of plasma configurations. Design iterations on the TF out of plane supports have eliminated stress concentrations in the inner keyways and have led to the choice of a so called friction-joint on the outside. The closure procedure for the TF case has been changed, with a new case segmentation, less risk of winding pack damage from shrinkage and better filling of the case-winding gaps. Selection of compact joints for the CS has enabled the peak field and cyclic stress levels in the conductor to be reduced while maintaining the flux capability. The uncertainty in the nuclear heat levels in the inner legs of the TF coils, and the need to operate with plasma nuclear powers from 360 to 700MW, lead to a thermal screen on the inside of the case with variable cooling capability. The electrical insulation specification has been refined after irradiation test results to give a better margin on the onset of degradation after operation to 3MWa/m 2 . The RWM stabilisation provided by the side CC has been extended by accepting higher voltages and heating from AC losses. R and D results from the model coil tests have shown lower than expected design margins for the Nb3Sn conductors. This has been offset by adopting the latest advances in strand performance, and the margins of the new conductor will be confirmed by testing in 2005. Preparation for procurement is underway with considerations on technically acceptable ways of splitting the magnet supply. (author)

  13. The design of a comprehensive microsimulator of household vehicle fleet composition, utilization, and evolution.

    Science.gov (United States)

    2012-01-01

    The report describes a comprehensive vehicle fleet composition, utilization, and evolution : simulator that can be used to forecast household vehicle ownership and mileage by type of : vehicle over time. The components of the simulator are developed ...

  14. Thermodynamic analysis of combined cycle under design/off-design conditions for its efficient design and operation

    International Nuclear Information System (INIS)

    Zhang, Guoqiang; Zheng, Jiongzhi; Xie, Angjun; Yang, Yongping; Liu, Wenyi

    2016-01-01

    Highlights: • Based on the PG9351FA gas turbine, two gas-steam combined cycles are redesigned. • Analysis of detailed off-design characteristics of the combined cycle main parts. • Suggestions for improving design and operation performance of the combined cycle. • Higher design efficiency has higher off-design efficiency in general PR range. • High pressure ratio combined cycles possess good off-design performance. - Abstract: To achieve a highly efficient design and operation of combined cycles, this study analyzed in detail the off-design characteristics of the main components of three combined cycles with different compressor pressure ratios (PRs) based on real units. The off-design model of combined cycle was built consisting of a compressor, a combustor, a gas turbine, and a heat recovery steam generator (HRSG). The PG9351FA unit is selected as the benchmark unit, on the basis of which the compressor is redesigned with two different PRs. Then, the design/off-design characteristics of the three units with different design PRs and the interactive relations between topping and bottoming cycles are analyzed with the same turbine inlet temperature (TIT). The results show that the off-design characteristics of the topping cycle affect dramatically the combined cycle performance. The variation range of the exergy efficiency of the topping cycle for the three units is between 11.9% and 12.4% under the design/off-design conditions. This range is larger than that of the bottoming cycle (between 9.2% and 9.5%). The HRSG can effectively recycle the heat/heat exergy of the gas turbine exhaust. Comparison among the three units shows that for a traditional gas-steam combined cycle, a high design efficiency results in a high off-design efficiency in the usual PR range. The combined cycle design efficiency of higher pressure ratio is almost equal to that of the PG9351FA, but its off-design efficiency is higher (maximum 0.42%) and the specific power decreases. As for

  15. Design and practice of a comprehensively functional integrated management information system for major construction

    Science.gov (United States)

    Liu, Yuling; Wang, Xiaoping; Zhu, Yuhui; Fei, Lanlan

    2017-08-01

    This paper introduces a Comprehensively Functional Integrated Management Information System designed for the Optical Engineering Major by the College of Optical Science and Engineering, Zhejiang University, which combines the functions of teaching, students learning, educational assessment and management. The system consists of 5 modules, major overview, online curriculum, experiment teaching management, graduation project management and teaching quality feedback. The major overview module introduces the development history, training program, curriculums and experiment syllabus and teaching achievements of optical engineering major in Zhejiang University. The Management Information System is convenient for students to learn in a mobile and personalized way. The online curriculum module makes it very easy for teachers to setup a website for new curriculums. On the website, teachers can help students on their problems about the curriculums in time and collect their homework online. The experiment teaching management module and the graduation project management module enables the students to fulfill their experiment process and graduation thesis under the help of their supervisors. Before students take an experiment in the lab, they must pass the pre-experiment quiz on the corresponding module. After the experiment, students need to submit the experiment report to the web server. Moreover, the module contains experiment process video recordings, which are very helpful to improve the effect of the experiment education. The management of the entire process of a student's graduation program, including the project selection, mid-term inspection, progress report of every two weeks, final thesis, et al, is completed by the graduation project management module. The teaching quality feedback module is not only helpful for teachers to know whether the education effect of curriculum is good or not, but also helpful for the administrators of the college to know whether the

  16. Software features and applications in process design, integration and operation

    Energy Technology Data Exchange (ETDEWEB)

    Dhole, V. [Aspen Tech Limited, Warrington (United Kingdom)

    1999-02-01

    Process engineering technologies and tools have evolved rapidly over the last twenty years. Process simulation/modeling, advanced process control, on-line optimisation, production planning and supply chain management are some of the examples of technologies that have rapidly matured from early commercial prototypes and concepts to established tools with significant impact on profitability of process industry today. Process Synthesis or Process Integration (PI) in comparison is yet to create its impact and still remains largely in the domain of few expert users. One of the key reasons as to why PI has not taken off is because the PI tools have not become integral components of the standard process engineering environments. On the last 15 years AspenTech has grown from a small process simulation tool provider to a large multinational company providing a complete suite of process engineering technologies and services covering process design, operation, planning and supply chain management. Throughout this period, AspenTech has acquired experience in rapidly evolving technologies from their early prototype stage to mature products and services. The paper outlines AspenTech`s strategy of integrating PI with other more established process design and operational improvement technologies. The paper illustrates the key elements of AspenTech`s strategy via examples of software development initiatives and services projects. The paper also outlines AspenTech`s future vision of the role of PI in process engineering. (au)

  17. Developing a Comprehensive Model of Intensive Care Unit Processes: Concept of Operations.

    Science.gov (United States)

    Romig, Mark; Tropello, Steven P; Dwyer, Cindy; Wyskiel, Rhonda M; Ravitz, Alan; Benson, John; Gropper, Michael A; Pronovost, Peter J; Sapirstein, Adam

    2015-04-23

    This study aimed to use a systems engineering approach to improve performance and stakeholder engagement in the intensive care unit to reduce several different patient harms. We developed a conceptual framework or concept of operations (ConOps) to analyze different types of harm that included 4 steps as follows: risk assessment, appropriate therapies, monitoring and feedback, as well as patient and family communications. This framework used a transdisciplinary approach to inventory the tasks and work flows required to eliminate 7 common types of harm experienced by patients in the intensive care unit. The inventory gathered both implicit and explicit information about how the system works or should work and converted the information into a detailed specification that clinicians could understand and use. Using the ConOps document, we created highly detailed work flow models to reduce harm and offer an example of its application to deep venous thrombosis. In the deep venous thrombosis model, we identified tasks that were synergistic across different types of harm. We will use a system of systems approach to integrate the variety of subsystems and coordinate processes across multiple types of harm to reduce the duplication of tasks. Through this process, we expect to improve efficiency and demonstrate synergistic interactions that ultimately can be applied across the spectrum of potential patient harms and patient locations. Engineering health care to be highly reliable will first require an understanding of the processes and work flows that comprise patient care. The ConOps strategy provided a framework for building complex systems to reduce patient harm.

  18. Operator interface design considerations for a PACS information management system

    Science.gov (United States)

    Steinke, James E.; Nabijee, Kamal H.; Freeman, Rick H.; Prior, Fred W.

    1990-08-01

    As prototype PACS grow into fully digital departmental and hospital-wide systems, effective information storage and retrieval mechanisms become increasingly important. Thus far, designers of PACS workstations have concentrated on image communication and display functionality. The new challenge is to provide appropriate operator interface environments to facilitate information retrieval. The "Marburg Model" 1 provides a detailed analysis of the functions, control flows and data structures used in Radiology. It identifies a set of "actors" who perform information manipulation functions. Drawing on this model and its associated methodology it is possible to identify four modes of use of information systems in Radiology: Clinical Routine, Research, Consultation, and Administration. Each mode has its own specific access requirements and views of information. An operator interface strategy appropriate for each mode will be proposed. Clinical Routine mode is the principal concern of PACS primary diagnosis workstations. In a full PACS implementation, such workstations must provide a simple and consistent navigational aid for the on-line image database, a local work list of cases to be reviewed, and easy access to information from other hospital information systems. A hierarchical method of information access is preferred because it provides the ability to start at high-level entities and iteratively narrow the scope of information from which to select subsequent operations. An implementation using hierarchical, nested software windows which fulfills such requirements shall be examined.

  19. The IXV Ground Segment design, implementation and operations

    Science.gov (United States)

    Martucci di Scarfizzi, Giovanni; Bellomo, Alessandro; Musso, Ivano; Bussi, Diego; Rabaioli, Massimo; Santoro, Gianfranco; Billig, Gerhard; Gallego Sanz, José María

    2016-07-01

    The Intermediate eXperimental Vehicle (IXV) is an ESA re-entry demonstrator that performed, on the 11th February of 2015, a successful re-entry demonstration mission. The project objectives were the design, development, manufacturing and on ground and in flight verification of an autonomous European lifting and aerodynamically controlled re-entry system. For the IXV mission a dedicated Ground Segment was provided. The main subsystems of the IXV Ground Segment were: IXV Mission Control Center (MCC), from where monitoring of the vehicle was performed, as well as support during pre-launch and recovery phases; IXV Ground Stations, used to cover IXV mission by receiving spacecraft telemetry and forwarding it toward the MCC; the IXV Communication Network, deployed to support the operations of the IXV mission by interconnecting all remote sites with MCC, supporting data, voice and video exchange. This paper describes the concept, architecture, development, implementation and operations of the ESA Intermediate Experimental Vehicle (IXV) Ground Segment and outlines the main operations and lessons learned during the preparation and successful execution of the IXV Mission.

  20. Spent Nuclear Fuel Cold Vacuum Drying facility comprehensive formal design review report

    International Nuclear Information System (INIS)

    HALLER, C.S.

    1999-01-01

    The majority of the Cold Vacuum Drying Facility (CVDF) design and construction is complete; isolated portions are still in the design and fabrication process. The project commissioned a formal design review to verify the sufficiency and accuracy of current design media to assure that: (1) the design completely and accurately reflects design criteria, (2) design documents are consistent with one another, and (3) the design media accurately reflects the current design. This review is a key element in the design validation and verification activities required by SNF-4396, ''Design Verification and Validation Plan For The Cold Vacuum Drying Facility''. This report documents the results of the formal design review

  1. Development of cloud-operating platform for detention facility design

    Science.gov (United States)

    Tun Lee, Kwan; Hung, Meng-Chiu; Tseng, Wei-Fan; Chan, Yi-Ping

    2017-04-01

    In the past 20 years, the population of Taiwan has accumulated in urban areas. The land development has changed the hydrological environment and resulted in the increase of surface runoff and shortened the time to peak discharge. The change of runoff characteristics increases the flood risk and reduces resilient ability of the city during flood. Considering that engineering measures may not be easy to implement in populated cities, detention facilities set on building basements have been proposed to compromise the increase of surface runoff resulting from development activities. In this study, a web-based operational platform has been developed to integrate the GIS technologies, hydrological analyses, as well as relevant regulations for the design of detention facilities. The design procedure embedded in the system includes a prior selection of type and size of the detention facility, integrated hydrological analysis for the developing site, and inspection of relevant regulations. After login the platform, designers can access the system database to retrieve road maps, land use coverages, and storm sewer information. Once the type, size, inlet, and outlet of the detention facility are assigned, the system can acquire the rainfall intensity-duration-frequency information from adjacent rain gauges to perform hydrological analyses for the developing site. The increase of the runoff volume due to the development and the reduction of the outflow peak through the construction of the detention facility can be estimated. The outflow peak at the target site is then checked with relevant regulations to confirm the suitability of the detention facility design. The proposed web-based platform can provide a concise layout of the detention facility and the drainageway of the developing site on a graphical interface. The design information can also be delivered directly through a web link to authorities for inspecting to simplify the complex administrative procedures.

  2. Environmental monitoring program design for uranium refining and conversion operations

    International Nuclear Information System (INIS)

    1984-08-01

    The objective of this study was to develop recommendations for the design of environmental monitoring programs at Canadian uranium refining and conversion operations. In order to develop monitoring priorities, chemical and radioactive releases to the air and water were developed for reference uranium refining and conversion facilities. The relative significance of the radioactive releases was evaluated through a pathways analysis which estimated dose to individual members of the critical receptor group. The effects of chemical releases to the environment were assessed by comparing predicted air and water contaminant levels to appropriate standards or guidelines. For the reference facilities studied, the analysis suggested that environmental effects are likely to be dominated by airborne release of both radioactive and nonradioactive contaminants. Uranium was found to be the most important radioactive species released to the air and can serve as an overall indicator of radiological impacts for any of the plants considered. The most important nonradioactive air emission was found to be fluoride (as hydrogen fluoride) from the uranium hexafluoride plant. For the uranium trioxide and uranium dioxide plants, air emissions of oxides of nitrogen were considered to be most important. The study recommendations for the design of an environmental monitoring program are based on consideration of those factors most likely to affect local air and water quality, and human radiation exposure. Site- and facility-specific factors will affect monitoring program design and the selection of components such as sampling media, locations and frequency, and analytical methods

  3. Design and Analysis for an Operator's Action Sharing System

    International Nuclear Information System (INIS)

    Jung, Yeonsub; Seong, Nokyu

    2013-01-01

    In the paper, contrary to HRP approach, no more FPD is introduced because there is no room to install. The same workstation and the same LDP should be utilized for ream transparency. A action sharing system will be introduced at ShinKori 3,4 MCR, and further applied to other APR1400 plant if necessary. The project started and applied by the end of 2014. Despite benefit of action sharing system, there are lots of challenges to overcome such as traffic load, and interfaces. The challenges have been analyzed thoroughly. Traffic load can be reduced through vector graphics, video driver, and capture and compressing techniques. Furthermore interfaces for action sharing system are developed and evaluated to reduce secondary workload. Advanced digital control rooms have lots of advantages compared to analog control room. They can integrate all process variables into more comprehensible forms. Advanced alarm processor can suppress trivial alarms, and P and ID based mimic isplays can be integrated with context sensitive menu for referencing. Moreover computer based procedures have been introduced at more advanced MCR. Because all these display appears at flat panel display (FPD), they can be easily modified if necessary. These days newly introduced MCRs are advanced types, and analog control rooms are no more built. In spite of this trend, advanced control rooms have shortage in view of team transparency. For example, shift supervisor cannot tell which devices reactor operator is manipulating. APR1400 MCR has large display panel to share the same situation awareness among crew member. Because LDP has fixed display comparing switchable display in FPD, situation awareness can be enhanced. However, even LDP cannot show the active device that crew member are manipulating due to either limited number of devices in LDP or no demarcation for the active device. During construction of ShinKori 3/4, the demarcation box for the active device has been introduced and called an Active

  4. Parametric Optimization of Some Critical Operating System Functions--An Alternative Approach to the Study of Operating Systems Design

    Science.gov (United States)

    Sobh, Tarek M.; Tibrewal, Abhilasha

    2006-01-01

    Operating systems theory primarily concentrates on the optimal use of computing resources. This paper presents an alternative approach to teaching and studying operating systems design and concepts by way of parametrically optimizing critical operating system functions. Detailed examples of two critical operating systems functions using the…

  5. The application of parameters for comprehensive smile esthetics by digital smile design programs: A review of literature

    Directory of Open Access Journals (Sweden)

    Doya Omar

    2018-01-01

    Full Text Available Cosmetic dentistry is increasingly becoming an issue of concern to patients who hope to improve their smile. A systematic and comprehensive dentofacial analysis must be performed before commencing esthetic treatment. Several computer software programs have been developed for digital smile design (DSD to assist clinicians in this process. This article compares DSD programs commonly used in cosmetic dentistry and their ability to assess esthetic parameters. A literature review was performed of current dentofacial aesthetic parameters and clinical applications of computer technology to assess facial, dentogingival and dental esthetics. Eight DSD programs (Photoshop CS6, Keynote, Planmeca Romexis Smile Design, Cerec SW 4.2, Aesthetic Digital Smile Design, Smile Designer Pro, DSD App and VisagiSMile were compared. Photoshop, Keynote and Aesthetic Digital Smile Design included the largest number of esthetic analysis parameters. Other studied DSD programs presented deficiencies in their ability to analyze facial esthetic parameters but included comprehensive dentogingival and dental esthetic functions. The DSD App, Planmeca Romexis Smile Design, and Cerec SW 4.2 were able to perform 3D analysis; furthermore, Cerec SW 4.2 and PRSD could be used jointly with CAD/CAM. The DSD App and Smile Designer Pro are available as mobile phone applications. It can be concluded that despite the fact that they were not specifically designed for dental diagnosis, Photoshop CS6 and Keynote provide a more comprehensive smile analysis than most specialized DSD programs. However, other program functions should also be considered when deciding which DSD program is applicable to individual clinical setups.

  6. Design and operation of a small (benchtop) pumped sodium loop

    International Nuclear Information System (INIS)

    Trevillion, E.A.; Rowe, D.M.J.

    1975-08-01

    The report outlines the design and operation of a small (benchtop) pumped sodium loop (sodium, 650g). The loop incorporates a diffusion cold trap to control the oxygen impurity level in the sodium and a sodium sampler/distillation unit to enable sodium samples to be analysed for impurities. Sodium flow rates of up to 5.5cm.s -1 (1cm 3 .s -1 ) have been achieved at temperatures up to 673.2K (400 0 C) and temperatures of up to 1023.2K (750 0 C) have been achieved under static conditions. A device for the addition and removal of metallic speciments to and from the loop sodium without contamination of either the specimens or the sodium is also described. (author)

  7. Safety in design and operation of low energy particle accelerators

    International Nuclear Information System (INIS)

    Badawy, I.

    1991-01-01

    This paper studies the safety in design and operation of low energy accelerators which produce beams of accelerated charged particles and radiations. As radiation sources, the accelerators are widely used in scientific research, industry, food and medical applications. The risks to human and environment are considered. The safety in accelerators is discussed-particularly-the shielding against ionizing radiations, overexposure to RF radiation fire hazards and power failures. Also the paper studies the emergency response at incidents. Emergency procedures are recommended for each type of emergency. Reporting to the competent Authority is also recommended to be prepared for each incident. The basic principles of regulatory control, licensing and inspections for accelerator facilities are discussed. The relation with the competent authority is pointed out. 4 fig

  8. The radioactive materials packaging handbook: Design, operations, and maintenance

    International Nuclear Information System (INIS)

    Shappert, L.B.; Bowman, S.M.; Arnold, E.D.

    1998-01-01

    As part of its required activities in 1994, the US Department of Energy (DOE) made over 500,000 shipments. Of these shipments, approximately 4% were hazardous, and of these, slightly over 1% (over 6,400 shipments) were radioactive. Because of DOE's cleanup activities, the total quantities and percentages of radioactive material (RAM) that must be moved from one site to another is expected to increase in the coming years, and these materials are likely to be different than those shipped in the past. Irradiated fuel will certainly be part of the mix as will RAM samples and waste. However, in many cases these materials will be of different shape and size and require a transport packaging having different shielding, thermal, and criticality avoidance characteristics than are currently available. This Handbook provides guidance on the design, testing, certification, and operation of packages for these materials

  9. Design of real-time operating system software

    International Nuclear Information System (INIS)

    Stafford, D.L.; Hulbert, A.J.

    1976-01-01

    Design of real-time data collection and control systems is complicated by problems not found in common sequential programming projects. Timing and synchronization are critical; data collection equipment is often completely foreign to mainframe programming facilities; operating system response to real-time events may be far too slow or too cumbersome. The philosophy at the Inhalation Toxicology Research Institute (ITRI) is to allow the investigators to do as much of their own programming as possible. Inasmuch as programming is not their primary responsibility or area of training, it is unreasonable to assume that they are familiar with the subtleties involved. The problem, therefore, has been to develop a system whereby investigators are able, with minimal consultation, to write, modify and otherwise maintain their own data collection and control programs and to do so with a minimum of destructive interaction with other data collection and control tasks

  10. Facilitating the design and operation of radiochemistry autosynthesizers

    International Nuclear Information System (INIS)

    Feliu, A.L.

    1990-01-01

    Both research and routine medical applications of positron emission tomography critically depend on rapid and reliable radiopharmaceutical syntheses. This work describes new computer techniques for controlling automated synthesizers, which feature: a graphical interface for easy operation, software reconfiguration without reprogramming to accommodate changes in chemistry, and both remote and unattended control modes. These concepts were implemented in a simple yet powerful program, PREPARE, which controls a commercially-built radiochemistry synthesizer, and in a fully-functional simulation, AUTOMATE, which explores synthesizer multitasking given a single PC. Unlike most black box and robotic approaches to radiochemistry synthesis which are highly chemistry- and hardware-specific, PREPARE and AUTOMATE have been designed as generic programs, supporting a palette of basic devices (valves, stepper motors, etc.)

  11. Design and operation of an interlaboratory comparison scheme

    International Nuclear Information System (INIS)

    Voiculescu, R. M.; Olteanu, M. C.; Nistor, V. M.

    2013-01-01

    The competence of laboratories is assessed by two complementary techniques. One of the techniques is the on-site evaluation following the requirements of ISO/IEC 17025:2005. The other one implies the proficiency testing which involves the determination of laboratory performance by means of interlaboratory comparisons, whereby the laboratory performs practical tests and their results are further compared with those of other laboratories. The paper treats one of the most important topics of the proficiency testing – the interlaboratory comparison (ILC). There will be presented the need, the purpose and the main objectives of an ILC and also a typically situation where an interlaboratory comparison exercise (for radio-analytical methods) was planned. A fully description of the design and operation of an ILC scheme is the main purpose of this paper. A special attention will be given to the data analysis and evaluation of interlaboratory comparison scheme results. (authors)

  12. Experiments simulation and design to set traffic lights operation rules

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez Garcia, J.A.

    2016-07-01

    In this paper it is used the experimental design to minimize the travel time of motor vehicles, in one of the most important avenues of Celaya City in Guanajuato, Mexico, by means of optimal synchronization of existing traffic lights. In the optimization process three factors are considered: the traffic lights’ cycle times, the synchrony defined as stepped, parallel and actual, and speed limit, each one with 3 evaluation levels. The response variables to consider are: motor vehicles’ travel time, fuel consumption and greenhouse effect gas (CO2) emissions. The different experiments are performed using the simulation model developed in the PTV-VISSIM software, which represents the vehicle traffic system. The obtained results for the different proposed scenarios allow to find proper levels at which the vehicle traffic system must be operated in order to improve mobility, to reduce contamination rates and decrease the fuel consumption for the different motor vehicles that use the avenue. (Author)

  13. Design, operation, and evaluation of the transportable vitrification system

    International Nuclear Information System (INIS)

    Zamecnik, J.R.; Young, S.R.; Hansen, E.K.; Whitehouse, J.C.

    1997-01-01

    The Transportable Vitrification System (TVS) is a transportable melter system designed to demonstrate the treatment of low-level and mixed hazardous and radioactive wastes such as wastewater treatment sludges, contaminated soils and incinerator ash. The TVS is a large-scale, fully integrated vitrification system consisting of melter feed preparation, melter, offgas, service, and control modules. The TVS was tested with surrogate waste at the Clemson University Environmental Systems Engineering Department's (ESED) DOE/Industry Center for Vitrification Research prior to being shipped to the DOE Oak Ridge Reservation (ORR) K-25 site for treatment of mixed waste. This testing, along with additional testing at ORR, proved that the TVS would be able to successfully treat mixed waste. These surrogate tests consistently produced glass that met the EPA Toxicity Characteristic Leaching Procedure (TCLP). Performance of the system resulted in acceptable emissions of regulated metals from the offgas system. The TVS is scheduled to begin mixed waste operations at ORR in June 1997

  14. The radioactive materials packaging handbook: Design, operations, and maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Shappert, L.B.; Bowman, S.M. [Oak Ridge National Lab., TN (United States); Arnold, E.D. [Lockheed Martin Energy Systems, Oak Ridge, TN (United States)] [and others

    1998-08-01

    As part of its required activities in 1994, the US Department of Energy (DOE) made over 500,000 shipments. Of these shipments, approximately 4% were hazardous, and of these, slightly over 1% (over 6,400 shipments) were radioactive. Because of DOE`s cleanup activities, the total quantities and percentages of radioactive material (RAM) that must be moved from one site to another is expected to increase in the coming years, and these materials are likely to be different than those shipped in the past. Irradiated fuel will certainly be part of the mix as will RAM samples and waste. However, in many cases these materials will be of different shape and size and require a transport packaging having different shielding, thermal, and criticality avoidance characteristics than are currently available. This Handbook provides guidance on the design, testing, certification, and operation of packages for these materials.

  15. Design and operational experience with a portable tritium cleanup system

    International Nuclear Information System (INIS)

    Maienschein, J.L.; Wilson, S.W.; Garcia, F.

    1991-06-01

    We built a portable tritium cleanup system to scavenge tritium from contaminated gases in any tritium-containing system in the LLNL Tritium Facility. The cleanup system uses standard catalytic oxidation of tritium to water followed by water removal with a molecular sieve dryer. The cleanup unit, complete with instrumentation, is contained in a portable cart that is rolled into place and connected to the apparatus to be cleaned. The cleanup systems is effective, low-tech, simple, and reliable. The nominal flow rate of the system is 30 liters/minute, and the decontamination factor is > 1000. In this paper we will show design information on our portable cleanup system, and will discuss our operational experience with it over the past several years

  16. Design of stirling engine operating at low temperature difference

    Directory of Open Access Journals (Sweden)

    Sedlák Josef

    2018-01-01

    Full Text Available There are many sources of free energy available in the form of heat that is often simply wasted. The aim of this paper is to design and build a low temperature differential Stirling engine that would be powered exclusively from heat sources such as waste hot water or focused solar rays. A prototype is limited to a low temperature differential modification because of a choice of ABSplus plastic as a construction material for its key parts. The paper is divided into two parts. The first part covers a brief history of Stirling engine and its applications nowadays. Moreover, it describes basic principles of its operation that are supplemented by thermodynamic relations. Furthermore, an analysis of applied Fused Deposition Modelling has been done since the parts with more complex geometry had been manufactured using this additive technology. The second (experimental part covers 4 essential steps of a rapid prototyping method - Computer Aided Design of the 3D model of Stirling engine using parametric modeller Autodesk Inventor, production of its components using 3D printer uPrint, assembly and final testing. Special attention was devoted to last two steps of the process since the surfaces of the printed parts were sandpapered and sprayed. Parts, where an ABS plus plastic would have impeded the correct function, had been manufactured from aluminium and brass by cutting operations. Remaining parts had been bought in a hardware store as it would be uneconomical and unreasonable to manufacture them. Last two chapters of the paper describe final testing, mention the problems that appeared during its production and propose new approaches that could be used in the future to improve the project.

  17. The design of intelligent support systems for nuclear reactor operators

    International Nuclear Information System (INIS)

    Bernard, J.A.

    1992-01-01

    This paper identifies factors relevant to the design of intelligent support systems and their use for the provision of real-time diagnostic information. As such, it constitutes a followup to the state-of-the-art review that was previously published by Bernard and Washio on the utilization of expert systems within the nuclear industry. Some major differences between intelligent-support tools and conventional expert systems are enumerated. In summary, conventional expert systems that encode experimental knowledge in production rules are not suitable vehicle for the creation of operator support systems. The principal difficulty is the need for real-time operation. This in turn means that intelligent support systems will have knowledge bases derived from temporally accurate plant models, inference engines that permit revisions in the search process to accommodate revised data, and man-machine interfaces that do not require any human input. Such systems will be heavily instrumented, and the associated knowledge bases will require a hierarchical organization to emulate human approaches to analysis

  18. Changing by Design: A Comprehensive Approach to School Reform. [Booklet with Audiotapes].

    Science.gov (United States)

    North Central Regional Educational Lab., Oak Brook, IL.

    Comprehensive school reform (CSR) focuses on reorganizing and revitalizing entire schools, rather than on implementing individual programs. The idea behind CSR is that schools cannot educate all students to high levels unless all the education system's components work together toward a common goal. Choosing a CSR model can be difficult and…

  19. Reading and Engineering: Elementary Students' Co-Application of Comprehension Strategies and Engineering Design Processes

    Science.gov (United States)

    Wilson-Lopez, Amy; Gregory, Stacie; Larsen, Victor

    2016-01-01

    For decades, researchers have asserted that K-12 teachers should embed reading comprehension instruction within each academic discipline, including "technical subjects" such as engineering. Recently, this assertion has become a source of controversy among researchers and practitioners who believe that time spent on teaching reading…

  20. ALT-II armor tile design for upgraded TEXTOR operation

    International Nuclear Information System (INIS)

    Newberry, B.L.; McGrath, R.T.; Watson, R.D.; Kohlhaas, W.; Finken, K.H.

    1994-01-01

    The upgrade of the TEXTOR tokamak at KFA Juelich was recently completed. This upgrade extended the TEXTOR pulse length from 5 seconds to 10 seconds. The auxiliary heating was increased to a total of 8.0 MW through a combination of neutral beam injection and radio frequency heating. Originally, the inertially cooled armor tiles of the full toroidal belt Advanced Limiter Test -- II (ALT-II) were designed for a 5-second operation with total heating of 6.0 MW. The upgrade of TEXTOR will increase the energy deposited per pulse onto the ALT-II by about 300%. Consequently, the graphite armor tiles for the ALT-II had to be redesigned to avoid excessively high graphite armor surface temperatures that would lead to unacceptable contamination of the plasma. This redesign took the form of two major changes in the ALT-II armor tile geometry. The first design change was an increase of the armor tile thermal mass, primarily by increasing the radial thickness of each tile from 17 mm to 20 mm. This increase in the radial tile dimension reduces the overall pumping efficiency of the ALT-II pump limiter by about 30%. The reduction in exhaust efficiency is unfortunate, but could be avoided only by active cooling of the ALT-II armor tiles. The active cooling option was too complicated and expensive to be considered at this time. The second design change involved redefining the plasma facing surface of each armor tile in order to fully utilize the entire surface area. The incident charged particle heat flux was distributed uniformly over the armor tile surfaces by carefully matching the radial, poloidal and toroidal curvature of each tile to the plasma flow in the TEXTOR boundary layer. This geometry redefinition complicates the manufacturing of the armor tiles, but results in significant thermal performance gains. In addition to these geometry upgrades, several material options were analyzed and evaluated

  1. The Mixed Waste Management Facility. Design basis integrated operations plan (Title I design)

    International Nuclear Information System (INIS)

    1994-12-01

    The Mixed Waste Management Facility (MWMF) will be a fully integrated, pilotscale facility for the demonstration of low-level, organic-matrix mixed waste treatment technologies. It will provide the bridge from bench-scale demonstrated technologies to the deployment and operation of full-scale treatment facilities. The MWMF is a key element in reducing the risk in deployment of effective and environmentally acceptable treatment processes for organic mixed-waste streams. The MWMF will provide the engineering test data, formal evaluation, and operating experience that will be required for these demonstration systems to become accepted by EPA and deployable in waste treatment facilities. The deployment will also demonstrate how to approach the permitting process with the regulatory agencies and how to operate and maintain the processes in a safe manner. This document describes, at a high level, how the facility will be designed and operated to achieve this mission. It frequently refers the reader to additional documentation that provides more detail in specific areas. Effective evaluation of a technology consists of a variety of informal and formal demonstrations involving individual technology systems or subsystems, integrated technology system combinations, or complete integrated treatment trains. Informal demonstrations will typically be used to gather general operating information and to establish a basis for development of formal demonstration plans. Formal demonstrations consist of a specific series of tests that are used to rigorously demonstrate the operation or performance of a specific system configuration

  2. Recent developments in the IAEA safety standards: design and operation of nuclear power plants

    International Nuclear Information System (INIS)

    Saito, Takehiko

    2004-01-01

    The IAEA has been publishing a wide variety of safety standards for nuclear and radiation related facilities and activities since 1978. In 1996, a more rigorously structured approach for the preparation and review of its safety standards was introduced. Currently, based on the approach, revision of most of the standards is in completion or near completion. The latest versions of the Safety Requirements for ''Design'' and ''Operation'' of nuclear power plants were respectively published in 2000. Currently, along with this revision of the Safety Requirements, many Safety Guides have been revised. In order to clarify the complicated revision procedure, an example of the entire revision process for a Safety Guide is provided. Through actual example of the revision process, enormous amount of work involved in the revision work is clearly indicated. The current status of all of the Safety Standards for Design and that for Operation of nuclear power plants are summarized. Summary of other IAEA safety standards currently revised and available related IAEA publications, together with information on the IAEA Web Site from where these documents can be downloaded, is also provided. The standards are reviewed to determine whether revision (or new issue) is necessary in five years following publication. The IAEA safety standards will continue to be updated through comprehensive and structured approach, collaboration of many experts of the world, and reflecting good practices of the world. The IAEA safety standards will serve to provide high level of safety assurance. (author)

  3. An independent spent-fuel storage installation at Surry Station: Design and operation

    International Nuclear Information System (INIS)

    McKay, H.S.; Wakeman, B.H.; Pickworth, J.M.; Routh, S.D.; Hopkins, W.C.

    1989-07-01

    Design and licensing of the Surry Power Station Independent Spent Fuel Storage Installation (ISFSI) was initiated in 1982 by Virginia Power as part of a comprehensive strategy to increase spent fuel storage capacity at the Station. Designed to use large, metal dry storage casks, the Surry ISFSI will accommodate 84 such casks with a total storage capacity of 811 MTU of spent PWR fuel assemblies. The ISFSI is located at the Surry Station in a wooded area approximately 1000 meters (3300 feet) east of the reactor facilities. Construction of the first of three reinforced concrete storage pads and its associated support systems was completed in March 1986. The operating license and Technical Specifications were issued by the US NRC on July 2, 1986. Initial loading operations of a General Nuclear Systems, Inc., CASTOR V/21 storage cask began in September 1986. The first two CASTOR V/21 casks were placed in storage at the ISFSI in December 1986. 16 refs., 33 figs., 16 tabs

  4. Lean Mission Operations Systems Design - Using Agile and Lean Development Principles for Mission Operations Design and Development

    Science.gov (United States)

    Trimble, Jay Phillip

    2014-01-01

    The Resource Prospector Mission seeks to rove the lunar surface with an in-situ resource utilization payload in search of volatiles at a polar region. The mission operations system (MOS) will need to perform the short-duration mission while taking advantage of the near real time control that the short one-way light time to the Moon provides. To maximize our use of limited resources for the design and development of the MOS we are utilizing agile and lean methods derived from our previous experience with applying these methods to software. By using methods such as "say it then sim it" we will spend less time in meetings and more time focused on the one outcome that counts - the effective utilization of our assets on the Moon to meet mission objectives.

  5. Design of comprehensive Alzheimer's disease centers to address unmet national needs.

    Science.gov (United States)

    Trojanowski, John Q; Arnold, Steven E; Karlawish, Jason H; Brunden, Kurt; Cary, Mark; Davatzikos, Christos; Detre, John; Gaulton, Glen; Grossman, Murray; Hurtig, Howard; Jedrziewski, Kathryn; McCluskey, Leo; Naylor, Mary; Polsky, Daniel; Schellenberg, Gerard D; Siderowf, Andrew; Shaw, Leslie M; Van Deerlin, Vivianna; Wang, Li-San; Werner, Rachel; Xie, Sharon X; Lee, Virginia M-Y

    2010-03-01

    The problem of Alzheimer's disease (AD) exemplifies the challenges of dealing with a broad range of aging-related chronic disorders that require long-term, labor-intensive, and expensive care. As the baby boom generation ages and brain diseases become more prevalent, the need to confront the pending health care crisis is more urgent than ever before. Indeed, there is now a critical need to expand significantly the national effort to solve the problem of AD, with special focus on prevention. The Campaign to Prevent Alzheimer's Disease by 2020 (PAD2020) aims to create a new paradigm for planning and supporting the organization of worldwide cooperative research networks to develop new technologies for early detection and treatments of aging-related memory and motor impairments. PAD 2020 is developing an implementation plan to justify (1) increasing the federal budget for research, (2) developing novel national resources to discover new interventions for memory and motor disorders, and (3) creating innovative and streamlined decision-making processes for selecting and supporting new ideas. Since 1978 the National Institute on Aging or National Institute of Health (NIH) established an extensive national network of AD research facilities at academic institutions including AD Centers (ADCs), Consortium to Establish a Registry for AD, AD Cooperative Study (ADCS), AD Drug Discovery Program, National Alzheimer's Coordinating Center, National Cell Repository for AD, and AD Neuroimaging Initiative. However, despite the success of these programs and their critical contributions, they are no longer adequate to meet the challenges presented by AD. PAD 2020 is designed to address these changes by improving the efficiency and effectiveness of these programs. For example, the ADCs (P30s and P50s) can be enhanced by converting some into Comprehensive Alzheimer's Disease Centers (CADCs) to support not only research, but also by being demonstration projects on care/treatment, clinical

  6. Candu Energy's Aging and Obsolescence Program and its Application to Operating Facilities and New Plant Design

    International Nuclear Information System (INIS)

    Dam, R.; Gold, R.; McCrea, L.

    2012-01-01

    While plant aging is inevitable, predictable and 'graceful 'aging' behavior can be achieved through the implementation of a comprehensive and integrated Plant Life Management (PLiM) program. Despite organizations like the IAEA and INPO placing more emphasis on equipment reliability, there is still a lack of completely integrated programs in the industry as evidenced by: - Piece-meal, often crisis-driven, implementation comprising many different, partial solutions; - Duplication of effort often seen when different groups work in 'silos'. A strategy which fits with existing plant processes and programs, and which coordinates a broad range of equipment reliability activities is key to achieving the desired results. An example of such a program is the Aging and Obsolescence Program (AOP). AOP follows application of INPO AP-913 guidance for equipment reliability. The program is augmented to include single point vulnerability identification, unified approach to short and long lived components, risk management, spare parts management, and the identification and resolution of obsolescence issues. The systematic nature of the program provides the needed foundation to old and new stations alike. For existing operating stations some of the key uses include outage interval extension, reduced forced outages, and/or outage time reduction, any of which can translate into improving plant performance, competitiveness, and significant dollars saved. Program elements applied to new plant design are commensurate with the industry direction to 'design for reliability', and has allowed Candu Energy to learn and to improve upon what it can offer to operating stations. This paper intends to describe the basic elements of Candu Energy's Aging and Obsolescence Program and will share some of the experience having applied it to existing operating stations, consider applications to support expanding regulatory requirements, and describe the integration into the design of new plants, promoting

  7. DESIGN MODELING OF A UNIVERSITY’S COMPREHENSIVE-INTEGRATED SECURITY SYSTEM

    Directory of Open Access Journals (Sweden)

    Marina V. Dulyasova

    2017-03-01

    Full Text Available Introduction: the safety of higher education institutions is considered to be of great importance nowadays. Security challenges need to be addressed through a comprehensive and integrative approach. This approach provides neutralisation of various threats systemically, risk prevention, minimisation of the tangible and moral harm. The project concept of “safe university” is proposed and substantiated for the above-mentioned purposes. Materials and Methods: the authors used a special literature survey on the issue, which is divided into three main groups of publications, where the complex security of educational institutions is considered in the context of the general theory of security, in the educational-methodical plan and within the framework of sociological, psychological and pedagogical approaches. The legislative and regulatory sources also indicated, legislative and regulatory legal acts reviews, “Safe City” concept, National standard “Information security technologies: complex and integrated ones. Standard requirements to architecture and technologies of intellectual systems of monitoring for safety of the companies and the territories” (State standard specification P 56875-2016, documents of higher education institutions, media reports. The analysis and generalisation of information was coupled with project modeling of the new comprehensive system of higher education institution security. Results: the authors introduce the concept, architecture and model of the comprehensive integrated higher education institution security, monitoring based on measures and indicators pertaining to implementation of standard requirements and level of satisfaction with safety, evaluation of the taken measures in terms of efficiency. Discussion and Conclusions: the main contours of the model for comprehensive integrated security system in a higher education institution and algorithm of interaction between the subjects are determined. These

  8. ALT-II armor tile design for upgraded TEXTOR operation

    International Nuclear Information System (INIS)

    Newberry, B.L.; McGrath, R.T.; Watson, R.D.

    1994-01-01

    The upgrade of the TEXTOR tokamak at KFA Julich will be completed in the spring of 1994. The upgrade will extend the TEXTOR pulse length from 5 seconds to 10 seconds. The auxiliary heating systems are also scheduled to be upgraded so that eventually a total of 8.0 MW auxiliary heating will be available through a combination of neutral beam injection and radio frequency heating. Originally, the inertially cooled armor tiles on the full toroidal belt Advanced Limiter Test - II (ALT-II) were designed for 5-second operation with a total heating power of 6.0 MW. The upgrade of TEXTOR will increase the energy deposited per pulse onto ALT-II by more than 300%. Consequently, the graphite armor tiles for ALT-II had to be redesigned in order to increase their thermal inertia and, thereby, avoid excessively high graphite armor surface temperatures that would lead to unacceptable contamination of the plasma. The armor tile thermal inertia had been increase primarily by expanding the radial thickness of the tiles from 17 mm to 20 mm. This increase in radial tile dimension will reduce the overall pumping efficiency of the ALT-II pump limiter by about 30%. The final armor tile design was a compromise between increasing the power handling capability and reducing the particle exhaust efficiency of ALT-II. The reduction in exhaust efficiency is unfortunate, but could only be avoided by active cooling of the ALT-II armor tiles. The active cooling option was too complicated and expensive to be considered at this time

  9. Dhruva: Main design features, operational experience and utilization

    Energy Technology Data Exchange (ETDEWEB)

    Agarwal, S.K. [Reactor Group, BARC, Trombay, Mumbai 400085 (India)]. E-mail: swarajagarwal2000@yahoo.com; Karhadkar, C.G. [Reactor Group, BARC, Trombay, Mumbai 400085 (India); Zope, A.K. [Reactor Group, BARC, Trombay, Mumbai 400085 (India); Singh, Kanchhi [Reactor Group, BARC, Trombay, Mumbai 400085 (India)

    2006-04-15

    Dhruva is a product of technological initiatives taken during mid seventies when a need was felt for another research reactor having a high neutron flux to meet the growing demands of research and development in the frontier areas of science and engineering. In addition production of radioisotopes of high specific activity and the diverse requirements of a broad based user community had to be synthesized into a viable system, which could be engineered within the limited means available in the country. This high neutron flux reactor was designed, constructed and commissioned entirely by Indian scientists and engineers and it reflects the country's resolve to achieve self-reliance in the nuclear reactor technology. Dhruva is a 100 MW (thermal) research reactor with metallic natural uranium as fuel, heavy water as moderator, coolant and reflector, giving a maximum thermal neutron flux of 1.8 x 10{sup 14} n/cm{sup 2}/s. Since its first criticality on 8th August 1985, a number of experimental facilities have been added which have proven to be highly attractive for universities and industrial researchers for their scientific merits in various fields. One of the major utilization areas has been the neutron beam research using several neutron spectrometers, all of which were built in-house. A guide tube facility comprising of two neutron guides and another experimental set-up with a multi-instrument beam line have enabled further enhancement of the utilization of this National Facility by the academic institutions in the country. Production of radioisotopes of high specific activity and in increased quantity has fulfilled growing demands for many applications. The write-up provides an overview of the reactor covering its design; layout, safety features, utilization and operating experience along with description of some of the specific experimental facilities.

  10. A comprehensive design methodology of organic Rankine cycles for the waste heat recovery of automotive heavy-duty diesel engines

    International Nuclear Information System (INIS)

    Amicabile, Simone; Lee, Jeong-Ik; Kum, Dongsuk

    2015-01-01

    One of the most promising approaches to recover the waste heat from internal combustion engines is the Organic Rankine Cycle owing to its efficiency and reliability. The design optimization of ORC, however, is nontrivial because there exist many design variables and practical considerations. The present paper proposes a comprehensive design methodology to optimize the Organic Rankine Cycles (ORC) considering a wide range of design variables as well as practical aspects such as component limitations and costs. The design process is comprised of three steps: heat source selection, candidate fluid selection, and thermodynamic cycle optimization. In order to select the best waste heat source, the available energy and other practical considerations of various heat sources have been compared. Among others, the Exhaust Gas Recirculation (EGR) cooler is found to be the best heat source, and thus used for the rest of this study. Based on a systematic working fluid analysis, Ethanol, Pentane, and R245fa are selected as three candidate fluids. For the comprehensive ORC optimization, four types of cycle layouts are considered; 1) subcritical cycle without a recuperator, 2) subcritical cycle with a recuperator, 3) supercritical without a recuperator, and 4) supercritical cycle with a recuperator. Four cycle layouts coupled with three candidate fluids give a total of twelve cycle analyses. Results show that the best performance is provided by the regenerative subcritical cycle with Ethanol, while the solution with minimum capital cost is the subcritical cycles with Ethanol but without a recuperator. - Highlights: • Selection of the best waste heat source of a diesel engine for a heat recovery system. • Screening process to identify the most suitable working fluids for the system. • Comprehensive ORC optimization is introduced for four types of cycle layouts. • Pay Back Time investigation to present the economic analysis of the cycles

  11. Design and operation of a remotely operated plutonium waste size reduction and material handling process

    International Nuclear Information System (INIS)

    Stewart, J.A. III; Charlesworth, D.L.

    1986-01-01

    Noncombustible 238 Pu and 239 Pu waste is generated as a result of normal operation and decommissioning activity at the Savannah River Plant, and is being retrievably stored there. As part of the long-term plant to process the stored waste and current waste for permanent disposal, a remote size reduction and material handling process is being cold-tested at Savannah River Laboratory. The process consists of a large, low-speed shredder and material handling system, a remote worktable, a bagless transfer system, and a robotically controlled manipulator. Initial testing of the shredder and material handling system and a cycle test of the bagless transfer system has been completed. Fabrication and acceptance testing of the Telerobat, a robotically controlled manipulator has been completed. Testing is scheduled to begin in 3/86. Design features maximizing the ability to remotely maintain the equipment were incorporated. Complete cold-testing of the equipment is scheduled to be completed in 1987

  12. Conducting and publishing design science research : Inaugural essay of the design science department of the Journal of Operations Management

    NARCIS (Netherlands)

    van Aken, Joan; Chandrasekaran, Aravind; Halman, Joop

    2016-01-01

    The new Design Science department at the Journal of Operations Management invites submissions using a design science research strategy for operations management (OM) issues. The objective of this strategy is to develop knowledge that can be used in a direct and specific way to design and implement

  13. Design and development of a Space Station proximity operations research and development mockup

    Science.gov (United States)

    Haines, Richard F.

    1986-01-01

    Proximity operations (Prox-Ops) on-orbit refers to all activities taking place within one km of the Space Station. Designing a Prox-Ops control station calls for a comprehensive systems approach which takes into account structural constraints, orbital dynamics including approach/departure flight paths, myriad human factors and other topics. This paper describes a reconfigurable full-scale mock-up of a Prox-Ops station constructed at Ames incorporating an array of windows (with dynamic star field, target vehicle(s), and head-up symbology), head-down perspective display of manned and unmanned vehicles, voice- actuated 'electronic checklist', computer-generated voice system, expert system (to help diagnose subsystem malfunctions), and other displays and controls. The facility is used for demonstrations of selected Prox-Ops approach scenarios, human factors research (work-load assessment, determining external vision envelope requirements, head-down and head-up symbology design, voice synthesis and recognition research, etc.) and development of engineering design guidelines for future module interiors.

  14. Design and operation of the Rover vacuum system

    International Nuclear Information System (INIS)

    Wagner, E.P. Jr.; Griffith, D.L.; Rivera, J.M.

    1997-01-01

    The Rover process for recovering unused uranium from graphite fuels was operated during 1983 and 1984, and then shut down in 1984. The first steps of the process used fluidized alumina beds to burn away the graphite and produce a uranium bearing ash. The ash was then transferred to a different process cell for acid dissolution. At the time of shutdown, a significant, but unmeasureable, quantity of highly enriched uranium was left in the process vessels. Normal decontamination procedures could not be used due to plugged process lines and the exclusion of moderator materials (water or finely divided organic substances) for criticality safety. The presence of highly enriched uranium in poorly defined quantity and configuration led to concerns for criticality safety, nuclear materials accountability, and physical security. A project was established to eliminate these concerns by cleaning and/or removing the process vessels, piping, and cells and sending the recovered Uranium Bearing Material (UBM) to secure storage. A key element of this project was the design of a system for collecting and transporting dry solids to a location where they could be loaded into critically favorable storage cans

  15. Optimum Design and Operation of Cyclic Storage Systems; Lumped Approach

    Directory of Open Access Journals (Sweden)

    Leila Ostadrahimi

    2007-01-01

    Full Text Available Conjunctive use of surface and groundwater resources is a preferred approach in water resources management. Compared to dam construction, groundwater has certain advantages, among which are less costs, less sedimentation and evaporation, fewer water quality problems, and less social and cultural problems. To reduce the major problems associated with the development of large-scale surface impoundment systems, cyclic storage systems can be used as an alternative. A cyclic storage system (CYCS is an integrated interactive system consisting of two subsystems of surface water storage (reservoir and groundwater; this system together with artificial recharge is able to satisfy the predefined demands with rather high reliability. In order to optimize these systems, one must consider the hydraulic interactions between all the components, but unfortunately it has been neglected in many studies. In this article, a nonlinear optimization model for design and operation of cyclic storage systems has been developed using the lumped approach. In order to evaluate the model, its results have been compared with the results of a model in which distributed approach had been deployed, and so the efficiency of lumped models to solve the problems of cyclic storage systems has been investigated.

  16. Nuclear safety approach for PWRs design and operation

    International Nuclear Information System (INIS)

    Vignon, D.

    1988-01-01

    The implementation of France's major nuclear programme - 56 PWR units in service or under construction - has gone hand in hand with the development of an original philosophy in the field of nuclear safety. From an initial core of deterministic safety philosophy current in the seventies, which has been wholly retained and in some instances refined, a range of additions has been made to include consideration of a number of additional situations based on a probabilistic approach. This has resulted in a better coherence for safety and a mitigation of the severe accident probability. Furthermore, the establishment of emergency plans has enabled the Safety Authorities and the operator to adopt a coherent and logical approach to severe accidents with the aim of achieving greater defence in depth, this has resulted in the provision of certain additional measures designed to further reduce the consequences of severe accidents. This paper describes the culmination of this work, as exemplified in the new 1 400MWe - N4 advanced plant series currently under construction, of which the essential elements are also incorporated into all previous units, thereby giving them an equivalent level of safety. This now constitutes the French safety policy with respect to PWR nuclear units

  17. Ergonomic design in the operating room: information technologies

    Science.gov (United States)

    Morita, Mark M.; Ratib, Osman

    2005-04-01

    The ergonomic design in the Surgical OR of information technology systems has been and continues to be a large problem. Numerous disparate information systems with unique hardware and display configurations create an environment similar to the chaotic environments of air traffic control. Patient information systems tend to show all available statistics making it difficult to isolate the key, relevant vitals for the patient. Interactions in this sterile environment are still being done with the traditional keyboard and mouse designed for cubicle office workflows. This presentation will address the shortcomings of the current design paradigm in the Surgical OR that relate to Information Technology systems. It will offer a perspective that addresses the ergonomic deficiencies and predicts how future technological innovations will integrate into this vision. Part of this vision includes a Surgical OR PACS prototype, developed by GE Healthcare Technologies, that addresses ergonomic challenges of PACS in the OR that include lack of portability, sterile field integrity, and UI targeted for diagnostic radiologists. GWindows (gesture control) developed by Microsoft Research and Voice command will allow for the surgeons to navigate and review diagnostic imagery without using the conventional keyboard and mouse that disrupt the integrity of the sterile field. This prototype also demonstrates how a wireless, battery powered, self contained mobile PACS workstation can be optimally positioned for a surgeon to reference images during an intervention as opposed to the current pre-operative review. Lessons learned from the creation of the Surgical OR PACS Prototype have demonstrated that PACS alone is not the end all solution in the OR. Integration of other disparate information systems and presentation of this information in simple, easy to navigate information packets will enable smoother interactions for the surgeons and other healthcare professionals in the OR. More intuitive

  18. Attention Process Training-3 to improve reading comprehension in mild aphasia: A single-case experimental design study.

    Science.gov (United States)

    Lee, Jaime B; Sohlberg, McKay Moore; Harn, Beth; Horner, Robert; Cherney, Leora R

    2018-06-04

    People with aphasia frequently present with nonlinguistic deficits, in addition to their compromised language abilities, which may contribute to their problems with reading comprehension. Treatment of attention, working memory and executive control may improve reading comprehension in individuals with aphasia, particularly those with mild reading problems. This single-case experimental design study evaluated the efficacy of Attention Process Training-3, an intervention combining direct attention training and metacognitive facilitation, for improving reading comprehension in individuals with mild aphasia. A multiple baseline design across six participants was used to evaluate treatment effects. The primary outcome measure was a maze reading task. Cognitive measures were administered pre- and post-treatment. Visual inspection of graphed maze reading performance data indicated a basic effect between APT-3 and improved maze reading for three of the six participants. Quantitative analyses, using Tau-U, corroborated findings identified through visual analysis. The overall effect size was significant (Tau = .48, p = .01). Results suggest that APT-3 has the potential to improve reading in individuals with aphasia, but that it may be more efficacious under certain conditions. Treatment and participant variables, including intensity of treatment and metacognitive strategy usage, are discussed as potential influences on participants' responsiveness to APT-3.

  19. Comprehensive Needs Assessment Study and Deployment of QFD Targeted at New Wheelchair Design

    Directory of Open Access Journals (Sweden)

    Sumit Desai

    2017-11-01

    Discussion: The results of this study are useful in understanding the perspective of Indian wheelchair users’ needs toward evidence-based wheelchair design. The design parameters with high absolute and relative technical importance can be selected to design new wheelchairs for Indian users in order to enhance the quality of life, comfort, and safety of people with disability.

  20. Greener manufacturing and operations: from design to delivery and back

    National Research Council Canada - National Science Library

    Sarkis, Joseph

    2001-01-01

    ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Joseph Sarkis, Clark University Graduate School of Management, USA 11 15 part 1. 1 : Operations Strategy and Policy...

  1. Enhancing Local Designers Skill in Rattan Furniture Industries in Cirebon through Comprehensive-Design Approach Regarding Buyers’ Dependencies Prevention

    Directory of Open Access Journals (Sweden)

    Andar Bagus Sriwarno

    2009-07-01

    Full Text Available Between the 1970s and the 1990s, the Indonesian economy has been transforming from an agriculture-based to an industry-based economy. According to this condition, Cirebon growth rapidly to export rattan goods even this city has no resources in rattan. The lack of design quality, export regulation and global economic crisis become the main factor to affect the decrease of company’s income at recent. Despite the crisis, government is now trying to recover by inviting design expert to improve design skills and capacity building of entrepreneurs in particular small-medium scale enterprises. This study aims to define why Cirebon still lags behind in industrial competitiveness regarding rattan furniture design. The intervention program of design is conducted to seek out the craftsman’s ability and determined the kind of design competitiveness advantages according their nature of business.

  2. The impact of home care nurses' numeracy and graph literacy on comprehension of visual display information: implications for dashboard design.

    Science.gov (United States)

    Dowding, Dawn; Merrill, Jacqueline A; Onorato, Nicole; Barrón, Yolanda; Rosati, Robert J; Russell, David

    2018-02-01

    To explore home care nurses' numeracy and graph literacy and their relationship to comprehension of visualized data. A multifactorial experimental design using online survey software. Nurses were recruited from 2 Medicare-certified home health agencies. Numeracy and graph literacy were measured using validated scales. Nurses were randomized to 1 of 4 experimental conditions. Each condition displayed data for 1 of 4 quality indicators, in 1 of 4 different visualized formats (bar graph, line graph, spider graph, table). A mixed linear model measured the impact of numeracy, graph literacy, and display format on data understanding. In all, 195 nurses took part in the study. They were slightly more numerate and graph literate than the general population. Overall, nurses understood information presented in bar graphs most easily (88% correct), followed by tables (81% correct), line graphs (77% correct), and spider graphs (41% correct). Individuals with low numeracy and low graph literacy had poorer comprehension of information displayed across all formats. High graph literacy appeared to enhance comprehension of data regardless of numeracy capabilities. Clinical dashboards are increasingly used to provide information to clinicians in visualized format, under the assumption that visual display reduces cognitive workload. Results of this study suggest that nurses' comprehension of visualized information is influenced by their numeracy, graph literacy, and the display format of the data. Individual differences in numeracy and graph literacy skills need to be taken into account when designing dashboard technology. © The Author 2017. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com

  3. The Work Design Questionnaire (WDQ): Developing and Validating a Comprehensive Measure for Assessing Job Design and the Nature of Work

    Science.gov (United States)

    Morgeson, Frederick P.; Humphrey, Stephen E.

    2006-01-01

    Although there are thousands of studies investigating work and job design, existing measures are incomplete. In an effort to address this gap, the authors reviewed the work design literature, identified and integrated previously described work characteristics, and developed a measure to tap those work characteristics. The resultant Work Design…

  4. A comprehensive continent-wide regionalisation investigation for daily design rainfall

    OpenAIRE

    F. Johnson; J. Green

    2018-01-01

    Study region: Australia. Study focus: Design rainfalls, in the form of Intensity Duration Frequency curves, are the standard input for most flood studies. Methods to combine rainfall data across space are required to provide optimal estimates of design rainfalls and constrain their uncertainty. This paper robustly investigates the use of a variety of regionalization methods to provide Australia wide design rainfall estimates using 8619 high quality rainfall stations. The influence of an indiv...

  5. Distributed Electric Propulsion Aircraft Comprehensive Analysis and Design Tool, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The solicitation seeks innovative approaches in designing and analyzing Distributed Electric Propulsion (DEP) aircraft to support ARMD's Strategic Thrust #3...

  6. Prosperity of Thought Versus Retreat of Application: A Comprehensive Approach in Urban Design Teaching

    Directory of Open Access Journals (Sweden)

    Abeer Mohamed Elshater

    2014-11-01

    Full Text Available This study focuses on a relevant question, practically in urban design studios; when will specialists discuss their educational visions around urban design in teaching plans? Currently, although Egyptian architecture and urban environments follow those of postwar European cities, numerous architectural schools teach the new urban design paradigm while ignoring the declining of cities. To reverse this trend, the author proposes that architectural educational institutions in Egypt need to alter their learning programs. Therefore, this study aims to create a new urban design module depends on outcomes based-learning consistent with the present Egyptian city scene on the basis of intended learning-outcomes.

  7. Design and Operation of a Cryogenic Nitrogen Pulsating Heat Pipe

    International Nuclear Information System (INIS)

    Fonseca, Luis Diego; Miller, Franklin; Pfotenhauer, John

    2015-01-01

    We report the design, experimental setup and successful test results using an innovative passive cooling system called a “Pulsating Heat Pipe” (PHP) operating at temperatures ranging from 77 K to 80 K and using nitrogen as the working fluid. PHPs, which transfer heat by two phase flow mechanisms through a closed loop tubing have the advantage that no electrical pumps are needed to drive the fluid flow. In addition, PHPs have an advantage over copper straps and thermal conductors since they are lighter in weight, exhibit lower temperature gradients and have higher heat transfer rates. PHPs consist of an evaporator section, thermally anchored to a solid, where heat is received at the saturation temperature where the liquid portion of the two-phase flow evaporates, and a condenser where heat is rejected at the saturation temperature where the vapor is condensed. The condenser section in our experiment has been thermally interfaced to a CT cryocooler from SunPower that has a cooling capacity of 10 W at 77 K. Alternating regions of liquid slugs and small vapor plugs fill the capillary tubing, with the vapor regions contracting in the condenser section and expanding in the evaporator section due to an electric heater that will generate heat loads up to 10 W. This volumetric expansion and contraction provides the oscillatory flow of the fluid throughout the capillary tubing thereby transferring heat from one end to the other. The thermal performance and temperature characteristics of the PHP will be correlated as a function of average condenser temperature, PHP fill liquid ratio, and evaporator heat load. The experimental data show that the heat transfer between the evaporator and condenser sections can produce an effective thermal conductivity up to 35000 W/m-K at a 3.5 W heat load. (paper)

  8. Design and Operation of a Cryogenic Nitrogen Pulsating Heat Pipe

    Science.gov (United States)

    Diego Fonseca, Luis; Miller, Franklin; Pfotenhauer, John

    2015-12-01

    We report the design, experimental setup and successful test results using an innovative passive cooling system called a “Pulsating Heat Pipe” (PHP) operating at temperatures ranging from 77 K to 80 K and using nitrogen as the working fluid. PHPs, which transfer heat by two phase flow mechanisms through a closed loop tubing have the advantage that no electrical pumps are needed to drive the fluid flow. In addition, PHPs have an advantage over copper straps and thermal conductors since they are lighter in weight, exhibit lower temperature gradients and have higher heat transfer rates. PHPs consist of an evaporator section, thermally anchored to a solid, where heat is received at the saturation temperature where the liquid portion of the two-phase flow evaporates, and a condenser where heat is rejected at the saturation temperature where the vapor is condensed. The condenser section in our experiment has been thermally interfaced to a CT cryocooler from SunPower that has a cooling capacity of 10 W at 77 K. Alternating regions of liquid slugs and small vapor plugs fill the capillary tubing, with the vapor regions contracting in the condenser section and expanding in the evaporator section due to an electric heater that will generate heat loads up to 10 W. This volumetric expansion and contraction provides the oscillatory flow of the fluid throughout the capillary tubing thereby transferring heat from one end to the other. The thermal performance and temperature characteristics of the PHP will be correlated as a function of average condenser temperature, PHP fill liquid ratio, and evaporator heat load. The experimental data show that the heat transfer between the evaporator and condenser sections can produce an effective thermal conductivity up to 35000 W/m-K at a 3.5 W heat load.

  9. MAIUS-1- Vehicle, Subsystems Design and Mission Operations

    Science.gov (United States)

    Stamminger, A.; Ettl, J.; Grosse, J.; Horschgen-Eggers, M.; Jung, W.; Kallenbach, A.; Raith, G.; Saedtler, W.; Seidel, S. T.; Turner, J.; Wittkamp, M.

    2015-09-01

    In November 2015, the DLR Mobile Rocket Base will launch the MAIUS-1 rocket vehicle at Esrange, Northern Sweden. The MAIUS-A experiment is a pathfinder atom optics experiment. The scientific objective of the mission is the first creation of a BoseEinstein Condensate in space and performing atom interferometry on a sounding rocket [3]. MAIUS-1 comprises a two-stage unguided solid propellant VSB-30 rocket motor system. The vehicle consists of a Brazilian 53 1 motor as 1 st stage, a 530 motor as 2nd stage, a conical motor adapter, a despin module, a payload adapter, the MAIUS-A experiment consisting of five experiment modules, an attitude control system module, a newly developed conical service system, and a two-staged recovery system including a nosecone. In contrast to usual payloads on VSB-30 rockets, the payload has a diameter of 500 mm due to constraints of the scientific experiment. Because of this change in design, a blunted nosecone is necessary to guarantee the required static stability during the ascent phase of the flight. This paper will give an overview on the subsystems which have been built at DLR MORABA, especially the newly developed service system. Further, it will contain a description of the MAIUS-1 vehicle, the mission and the unique requirements on operations and attitude control, which is additionally required to achieve a required attitude with respect to the nadir vector. Additionally to a usual microgravity environment, the MAIUS-l payload requires attitude control to achieve a required attitude with respect to the nadir vector.

  10. Universal Design for Learning: Cognitive Theory into Practice for Facilitating Comprehension in Early Literacy

    Science.gov (United States)

    Brand, Susan Trostle; Dalton, Elizabeth M.

    2012-01-01

    Addressing the unique needs of children of all ages and abilities, Universal Design for Learning (UDL) is gaining momentum in schools and preschools around the nation and the globe. This article explores Universal Design for Learning and its promising applications to a variety of reading and language arts experiences in the Early Childhood…

  11. Remedial design work plan for Lower East Fork Poplar Creek Operable Unit, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    1995-10-01

    The Remedial Design Work Plan (RDWP) for Lower East Fork Poplar Creek (EFPC) Operable Unit (OU) in Oak Ridge, Tennessee. This remedial action fits into the overall Oak Ridge Reservation (ORR) cleanup strategy by addressing contaminated floodplain soil. The objective of this remedial action is to minimize the risk to human health and the environment from contaminated soil in the Lower EFPC floodplain pursuant to the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) and the Federal Facility Agreement (FFA) (1992). In accordance with the FFA, a remedial investigation (RI) (DOE 1994a) and a feasibility study (DOE 1994b) were conducted to assess contamination of the Lower EFPC and propose remediation alternatives. The remedial investigation determined that the principal contaminant is mercury, which originated from releases during Y-12 Plant operations, primarily between 1953 and 1963. The recommended alternative by the feasibility study was to excavate and dispose of floodplain soils contaminated with mercury above the remedial goal option. Following the remedial investigation/feasibility study, and also in accordance with the FFA, a proposed plan was prepared to more fully describe the proposed remedy.

  12. Design of comprehensive plant information system considering maintenance indicators in nuclear power plant

    International Nuclear Information System (INIS)

    Takata, Takashi; Yamaguchi, Akira; Yamamoto, Akio

    2013-01-01

    A safety of a nuclear power plant must be ensured and maintained through its entire plant life. For this plant life cycle safety (PLCS), a comprehensive plant information system, in which an each maintenance record of the plant is taken into consideration, is of importance. In this paper, a development of a plant chart, which is a part of the information system, has been developed based on a defense-in-depth concept that is one of the most important concept to ensure the plant safety. In the chart, an updated probability of loss of a component or function is used as a maintenance indicator and a probabilistic risk assessment (PRA) method is applied to quantify the plant status in the chart. (author)

  13. Secure Retrieval of FFTF Testing, Design, and Operating Information

    International Nuclear Information System (INIS)

    Butner, R. Scott; Wootan, David W.; Omberg, Ronald P.; Makenas, Bruce J.; Nielsen, Deborah

    2009-01-01

    One of the goals of the Advanced Fuel Cycle Initiative (AFCI) is to preserve the knowledge that has been gained in the United States on Liquid Metal Reactors (LMR). In addition, preserving LMR information and knowledge is part of a larger international collaborative activity conducted under the auspices of the International Atomic Energy Agency (IAEA). A similar program is being conducted for EBR-II at the Idaho Nuclear Laboratory (INL) and international programs are also in progress. Knowledge preservation at the FFTF is focused on the areas of design, construction, startup, and operation of the reactor. As the primary function of the FFTF was testing, the focus is also on preserving information obtained from irradiation testing of fuels and materials. This information will be invaluable when, at a later date, international decisions are made to pursue new LMRs. In the interim, this information may be of potential use for international exchanges with other LMR programs around the world. At least as important in the United States, which is emphasizing large-scale computer simulation and modeling, this information provides the basis for creating benchmarks for validating and testing these large scale computer programs. Although the preservation activity with respect to FFTF information as discussed below is still underway, the team of authors above is currently retrieving and providing experimental and design information to the LMR modeling and simulation efforts for use in validating their computer models. On the Hanford Site, the FFTF reactor plant is one of the facilities intended for decontamination and decommissioning consistent with the cleanup mission on this site. The reactor facility has been deactivated and is being maintained in a cold and dark minimal surveillance and maintenance mode until final decommissioning is pursued. In order to ensure protection of information at risk, the program to date has focused on sequestering and secure retrieval

  14. Design and operation of gas-heated thermal pumping units

    Energy Technology Data Exchange (ETDEWEB)

    Rostek, H A [Ruhrgas A.G., Essen (Germany, F.R.)

    1979-03-01

    The first gas heat pump systems have been operated since spring 1977. These are applied in living houses, school, swimming pools, and sport places and administration buildings. The heating performance of these systems is 150-3800 kW. Two of these systems, one in a swimming pool and one in a house for several families are operating, each of them for one heating period. The operational experiences with these gas heat pumps are reported on, basing on measurement results. The experience gathered from the operation of gas heat pumps systems is applied to the planning of other plants. The development of a standardized gas heat pump-series is emphasized.

  15. [Effects of the new comprehensive system for designating illegal drug components on the abuse of designer drugs and future problems based on an online questionnaire].

    Science.gov (United States)

    Morino, Taichi; Okazaki, Mitsuhiro; Toda, Takaki; Yokoyama, Takashi

    2015-12-01

    Recently, the abuse of designer drugs has become a social problem. Designer drugs are created by modifying part of the chemical structure of drugs that have already been categorized as illegal, thereby creating a different chemical compound in order to evade Pharmaceutical Affairs Law regulations. The new comprehensive system for designating illegal drug components has been in effect since March 2013, and many designer drugs can now be regulated. We conducted an online questionnaire survey of people with a history of designer drug use to elucidate the effects of the new system on the abuse of designer drugs and to identify potential future problems. Over half the subjects obtained designer drugs only before the new system was implemented. Awareness of the system was significantly lower among subjects who obtained designer drugs for the first time after its introduction than those who obtained the drugs only before its implementation. Due to the new system, all methods of acquiring designer drugs saw decreases in activity. However, the ratio of the acquisition of designer drugs via the Internet increased. Since over 50% of the subjects never obtained designer drugs after the new system was introduced, goals that aimed to make drug procurement more difficult were achieved. However, awareness of the new system among subjects who obtained designer drugs after the new system was introduced was significantly low. Therefore, fostering greater public awareness of the new system is necessary. The results of the questionnaire also suggested that acquiring designer drugs through the Internet has hardly been affected by the new system. We strongly hope that there will be a greater push to restrict the sale of designer drugs on the Internet in the near future.

  16. Knowledge-based support for design and operational use of human-machine interfaces

    International Nuclear Information System (INIS)

    Johannsen, G.

    1994-01-01

    The possibilities for knowledge support of different human user classes, namely operators, operational engineers and designers of human-machine interfaces, are discussed. Several human-machine interface functionalities are briefly explained. The paper deals with such questions as which type of knowledge is needed for design and operation, how to represent it, where to get it from, how to process it, and how to consider and use it. The relationships between design and operational use are thereby emphasised. (author)

  17. Use of designated boat operators and designated drivers among college students.

    Science.gov (United States)

    Cheong, JeeWon; Hall, Nicole M; MacKinnon, David P

    2006-07-01

    Prior research has shown that designated drivers (DD) are widely used as a preventive measure for driving under the influence. Despite the prevalence of alcohol involvement in boating accidents, much less is known about the use of a designated boat operator (DBO). The current study investigated the prevalence of DBO use in recreational boating and compared the characteristics of DD users and DBO users. Several survey questionnaires were distributed to a group of undergraduate students at a large southwestern university for the purpose of investigating demographic characteristics, alcohol-use pattern, and other alcohol-related problem behaviors, such as driving and boating under the influence. Approximately 45% of the boaters reported they had drunk alcohol while boating, and approximately 70% had used a DBO in the most recent boating event. The DBO users were found to be similar to the DD users in terms of drinking pattern, age of drinking onset, and driving behaviors. High rates of alcohol use in recreational boating suggest the need for prevention strategies. Furthermore, future studies are needed to investigate the selection process of the DBOs and the differences between passengers and boat operators, which could shed light on strategies to prevent alcohol- involved boating injuries.

  18. Design and development of high voltage high power operational ...

    Indian Academy of Sciences (India)

    Applications of power operational amplifiers (opamps) are increasing day by day in the industry as they are used in audio amplifiers, Piezo transducer systems and the electron deflection systems. Power operational amplifiers have all the features of a general purpose opamp except the additional power handling capability.

  19. Nickel-Cadmium Battery Operation Management Optimization Using Robust Design

    Science.gov (United States)

    Blosiu, Julian O.; Deligiannis, Frank; DiStefano, Salvador

    1996-01-01

    In recent years following several spacecraft battery anomalies, it was determined that managing the operational factors of NASA flight NiCd rechargeable battery was very important in order to maintain space flight battery nominal performance. The optimization of existing flight battery operational performance was viewed as something new for a Taguchi Methods application.

  20. Design and modeling of reservoir operation strategies for sediment management

    NARCIS (Netherlands)

    Sloff, C.J.; Omer, A.Y.A.; Heynert, K.V.; Mohamed, Y.A.

    2015-01-01

    Appropriate operation strategies that allow for sediment flushing and sluicing (sediment routing) can reduce rapid storage losses of (hydropower and water-supply) reservoirs. In this study we have shown, using field observations and computational models, that the efficiency of these operations

  1. Radiation protection in the design and operation of Sizewell B

    International Nuclear Information System (INIS)

    Oldfield, M.

    1989-01-01

    This paper raises Health Physics operational issues specific to PWR or not previously encountered by the CEGB, which need to be resolved before the operation of Sizewell B and its replica successors. Staffing, access to contamination areas, training, temporary scaffolding and temporary lead shielding are discussed and the author makes some observations and suggestions. (author)

  2. Design of A Vibration and Stress Measurement System for an Advanced Power Reactor 1400 Reactor Vessel Internals Comprehensive Vibration Assessment Program

    International Nuclear Information System (INIS)

    Ko, Doyoung; Kim, Kyuhyung

    2013-01-01

    In accordance with the US Nuclear Regulatory Commission (US NRC), Regulatory Guide 1.20, the reactor vessel internals comprehensive vibration assessment program (RVI CVAP) has been developed for an Advanced Power Reactor 1400 (APR1400). The purpose of the RVI CVAP is to verify the structural integrity of the reactor internals to flow-induced loads prior to commercial operation. The APR1400 RVI CVAP consists of four programs (analysis, measurement, inspection, and assessment). Thoughtful preparation is essential to the measurement program, because data acquisition must be performed only once. The optimized design of a vibration and stress measurement system for the RVI CVAP is essential to verify the integrity of the APR1400 RVI. We successfully designed a vibration and stress measurement system for the APR1400 RVI CVAP based on the design materials, the hydraulic and structural analysis results, and performance tests of transducers in an extreme environment. The measurement system designed in this paper will be utilized for the APR1400 RVI CVAP as part of the first construction project in Korea

  3. DESIGN OF A VIBRATION AND STRESS MEASUREMENT SYSTEM FOR AN ADVANCED POWER REACTOR 1400 REACTOR VESSEL INTERNALS COMPREHENSIVE VIBRATION ASSESSMENT PROGRAM

    Directory of Open Access Journals (Sweden)

    DO-YOUNG KO

    2013-04-01

    Full Text Available In accordance with the US Nuclear Regulatory Commission (US NRC, Regulatory Guide 1.20, the reactor vessel internals comprehensive vibration assessment program (RVI CVAP has been developed for an Advanced Power Reactor 1400 (APR1400. The purpose of the RVI CVAP is to verify the structural integrity of the reactor internals to flow-induced loads prior to commercial operation. The APR1400 RVI CVAP consists of four programs (analysis, measurement, inspection, and assessment. Thoughtful preparation is essential to the measurement program, because data acquisition must be performed only once. The optimized design of a vibration and stress measurement system for the RVI CVAP is essential to verify the integrity of the APR1400 RVI. We successfully designed a vibration and stress measurement system for the APR1400 RVI CVAP based on the design materials, the hydraulic and structural analysis results, and performance tests of transducers in an extreme environment. The measurement system designed in this paper will be utilized for the APR1400 RVI CVAP as part of the first construction project in Korea.

  4. Bridging operation and design. The encounter between practical and discipline-based knowledge in offshore platform design

    Energy Technology Data Exchange (ETDEWEB)

    Husemoen, Mette Suzanne

    1998-12-31

    This thesis investigates the relationship between operations and design and the design process, taking as case studies the two new platforms of Phillips Petroleum Company Norway on Ekofisk II, the Ekofisk 2/4 X drilling and wellhead platform and the Ekofisk 2/4 J processing and transportation platform. The emphasis has been on how to take into account operational experience in design. The two research questions are: (1) Are operations and design two communities-of-practice based on different kinds of knowledge?, and (2) What are the conditions for bridging knowledge in operations and design? From the theory reviewed and the field data presented the study concludes that physical closeness and integration of operations and design personnel, experience from the other community-of-practice, and mutual sympathy, trust, and respect, are important factors in bridging knowledge of the operations and design communities-of-practice and creating innovative solutions in design which transcend the existing knowledge in operations and design. 66 refs., 28 figs., 8 tabs.

  5. Bridging operation and design. The encounter between practical and discipline-based knowledge in offshore platform design

    Energy Technology Data Exchange (ETDEWEB)

    Husemoen, Mette Suzanne

    1997-12-31

    This thesis investigates the relationship between operations and design and the design process, taking as case studies the two new platforms of Phillips Petroleum Company Norway on Ekofisk II, the Ekofisk 2/4 X drilling and wellhead platform and the Ekofisk 2/4 J processing and transportation platform. The emphasis has been on how to take into account operational experience in design. The two research questions are: (1) Are operations and design two communities-of-practice based on different kinds of knowledge?, and (2) What are the conditions for bridging knowledge in operations and design? From the theory reviewed and the field data presented the study concludes that physical closeness and integration of operations and design personnel, experience from the other community-of-practice, and mutual sympathy, trust, and respect, are important factors in bridging knowledge of the operations and design communities-of-practice and creating innovative solutions in design which transcend the existing knowledge in operations and design. 66 refs., 28 figs., 8 tabs.

  6. COST 296 scientific results designed for operational use

    Directory of Open Access Journals (Sweden)

    Michael Pezzopane

    2009-06-01

    ="margin: 0.0px 0.0px 0.0px 0.0px; font: 9.0px Times;">COST 296 Action prepared those services that implemented the new design techniques for the newly announced

    EU and ESA policy-Space Situation Awareness (SSA. COST 296 developments applied to nowcasting and forecasting services are an essential input to the Operational SSA Ionosphere.



  7. Practical design for robot operating in radiation condition

    International Nuclear Information System (INIS)

    Oomichi, Takeo; Isozaki, Yoshifumi

    2002-01-01

    It is proposed systematic design for radiation resistance robot based on irradiation test and estimating damage lifetime by reliable technology. Reducing design time and cost, key device IC is classified to non-exchange, no use and use after radiation test by analyzing robot function and IC function. Since the damage lifetime verified normal distribution under radiation test of IC, the proposed design method is effective for practical radiation resistance robot. (author)

  8. Database reliability engineering designing and operating resilient database systems

    CERN Document Server

    Campbell, Laine

    2018-01-01

    The infrastructure-as-code revolution in IT is also affecting database administration. With this practical book, developers, system administrators, and junior to mid-level DBAs will learn how the modern practice of site reliability engineering applies to the craft of database architecture and operations. Authors Laine Campbell and Charity Majors provide a framework for professionals looking to join the ranks of today’s database reliability engineers (DBRE). You’ll begin by exploring core operational concepts that DBREs need to master. Then you’ll examine a wide range of database persistence options, including how to implement key technologies to provide resilient, scalable, and performant data storage and retrieval. With a firm foundation in database reliability engineering, you’ll be ready to dive into the architecture and operations of any modern database. This book covers: Service-level requirements and risk management Building and evolving an architecture for operational visibility ...

  9. 40 CFR 264.1101 - Design and operating standards.

    Science.gov (United States)

    2010-07-01

    ... the American Concrete Institute (ACI) and the American Society of Testing Materials (ASTM) in judging... they are exposed; climatic conditions; and the stresses of daily operation, including the movement of...

  10. 40 CFR 265.1101 - Design and operating standards.

    Science.gov (United States)

    2010-07-01

    ... industry such as the American Concrete Institute (ACI) and the American Society of Testing Materials (ASTM... wastes to which they are exposed; climatic conditions; and the stresses of daily operation, including the...

  11. FFTF fuel pin design procedure verification for transient operation

    International Nuclear Information System (INIS)

    Baars, R.E.

    1975-05-01

    The FFTF design procedures for evaluating fuel pin transient performance are briefly reviewed, and data where available are compared with design procedure predictions. Specifically, burst conditions derived from Fuel Cladding Transient Tester (FCTT) tests and from ANL loss-of-flow tests are compared with burst pressures computed using the design procedure upon which the cladding integrity limit was based. Failure times are predicted using the design procedure for evaluation of rapid reactivity insertion accidents, for five unterminated TREAT experiments in which well characterized fuel failures were deliberately incurred. (U.S.)

  12. 30 CFR 250.1628 - Design, installation, and operation of production systems.

    Science.gov (United States)

    2010-07-01

    ... Operations § 250.1628 Design, installation, and operation of production systems. (a) General. All production... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Design, installation, and operation of production systems. 250.1628 Section 250.1628 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT OF...

  13. Conceptual design report for a remotely operated cask handling system

    International Nuclear Information System (INIS)

    Yount, J.A.; Berger, J.D.

    Recent advances in remote handling utilizing commercial robotics are conceptually applied to the problem of lowering operator cumulative dose and increasing throughput during cask handling operations in proposed nuclear waste container shipping and receiving facilities. The functional criteria for each subsystem are defined, and candidate systems are described. The report also contains a generic description of a waste receiving facility, to show possible deployment configurations for the equipment

  14. Designing Efficient and Effective, Operationally Relevant, High Altitude Training Profiles

    Science.gov (United States)

    2001-06-01

    Operational Medical Issues in Hypo-and Hyperbaric Conditions [les Questions medicales a caractere oprationel liees aux conditions hypobares ou... hyperbares ] To order the complete compilation report, use: ADA395680 The component part is provided here to allow users access to individually authored...Airforce was felt to meet this need and was recommended. Paper presented at the RTO HFM Symposium on "Operational Medical Issues in Hypo- and Hyperbaric

  15. Integrating Kano’s Model into Quality Function Deployment for Product Design: A Comprehensive Review

    Science.gov (United States)

    Ginting, Rosnani; Hidayati, Juliza; Siregar, Ikhsan

    2018-03-01

    Many methods and techniques are adopted by some companies to improve the competitiveness through the fulfillment of customer satisfaction by enhancement and improvement the product design quality. Over the past few years, several researcher have studied extensively combining Quality Function Deployment and Kano’s model as design techniques by focusing on translating consumer desires into a product design. This paper presents a review and analysis of several literatures that associated to the integration methodology of Kano into the QFD process. Various of international journal articles were selected, collected and analyzed through a number of relevant scientific publications. In-depth analysis was performed, and focused in this paper on the results, advantages and drawbacks of its methodology. In addition, this paper also provides the analysis that acquired in this study related to the development of the methodology. It is hopedd this paper can be a reference for other researchers and manufacturing companies to implement the integration method of QFD- Kano for product design.

  16. Toward a Current, Comprehensive, Integrative, and Flexible Model of Motivation for Instructional Design

    Science.gov (United States)

    Hardre, Patricia L.; Miller, Raymond B.

    2006-01-01

    Workplace motivation historically has been an HR function, with ID as a training function. This division produces a split between motivation and training, leaving them isolated from one another. Intervention design needs to include motivation throughout its phases, to maximize motivating opportunities for performance improvement. The current…

  17. Design of Virtual Environments for the Comprehension of Planetary Phenomena Based on Students' Ideas.

    Science.gov (United States)

    Bakas, Christos; Mikropoulos, Tassos A.

    2003-01-01

    Explains the design and development of an educational virtual environment to support the teaching of planetary phenomena, particularly the movements of Earth and the sun, day and night cycle, and change of seasons. Uses an interactive, three-dimensional (3D) virtual environment. Initial results show that the majority of students enthused about…

  18. Product quality driven design of bakery operations using dynamic optimization

    NARCIS (Netherlands)

    Hadiyanto, M.; Esveld, D.C.; Boom, R.M.; Straten, van G.; Boxtel, van A.J.B.

    2008-01-01

    Abstract Quality driven design uses specified product qualities as a starting point for process design. By backward reasoning the required process conditions and processing system were found. In this work dynamic optimization was used as a tool to generate processing solutions for baking processes

  19. Modelling, Design, Operability and Analysis of Reaction-Separation Systems

    DEFF Research Database (Denmark)

    Jimenez, Edgar Ramirez

    2006-01-01

    opførsel er essentiel for bedste valg af operationsstrategi kontrolstruktur. Denne modelbaserede metode har vist sit potentiale for mere komplekse RSE processer til at identificere de vigtigste problemer fra det integrerede design og kontrolproblem. Bemærk at identifikationen af de vigtige design og...

  20. The National Long Term Care Demonstration: operational issues encountered in developing the research design.

    Science.gov (United States)

    Carcagno, G J; Kemper, P

    1983-01-01

    This paper describes the design of the National Long Term Care Demonstration and its evaluation and discusses a number of operational issues encountered in the design process: simultaneous design of research and operations, identification of the target population, randomization, collection of comparable data, development of an assessment instrument, potential changes in existing programs, and termination planning.

  1. Prediction of contact mechanics in metal-on-metal Total Hip Replacement for parametrically comprehensive designs and loads.

    Science.gov (United States)

    Donaldson, Finn E; Nyman, Edward; Coburn, James C

    2015-07-16

    Manufacturers and investigators of Total Hip Replacement (THR) bearings require tools to predict the contact mechanics resulting from diverse design and loading parameters. This study provides contact mechanics solutions for metal-on-metal (MoM) bearings that encompass the current design space and could aid pre-clinical design optimization and evaluation. Stochastic finite element (FE) simulation was used to calculate the head-on-cup contact mechanics for five thousand combinations of design and loading parameters. FE results were used to train a Random Forest (RF) surrogate model to rapidly predict the contact patch dimensions, contact area, pressures and plastic deformations for arbitrary designs and loading. In addition to widely observed polar and edge contact, FE results included ring-polar, asymmetric-polar, and transitional categories which have previously received limited attention. Combinations of design and load parameters associated with each contact category were identified. Polar contact pressures were predicted in the range of 0-200 MPa with no permanent deformation. Edge loading (with subluxation) was associated with pressures greater than 500 MPa and induced permanent deformation in 83% of cases. Transitional-edge contact (with little subluxation) was associated with intermediate pressures and permanent deformation in most cases, indicating that, even with ideal anatomical alignment, bearings may face extreme wear challenges. Surrogate models were able to accurately predict contact mechanics 18,000 times faster than FE analyses. The developed surrogate models enable rapid prediction of MoM bearing contact mechanics across the most comprehensive range of loading and designs to date, and may be useful to those performing bearing design optimization or evaluation. Published by Elsevier Ltd.

  2. Architecture Studio Archive: A Case Study in the Comprehensive Digital Capture and Repository of Student Design Work as an Aid to Teaching, Research, and Accreditation

    Science.gov (United States)

    Anderson, Ross; Arndell, Michael; Christensen, Sten

    2009-01-01

    The "Architecture Studio Archive" pilot sought to form a comprehensive digital archive of the diverse student work conducted in the first year of the Bachelor of Design in Architecture Degree at the University of Sydney. The design studio is the primary vehicle for teaching architectural design. It is a locus for creative activity, with…

  3. Information architecture considerations in designing a comprehensive tuberculosis enterprise system in Western Kenya.

    Science.gov (United States)

    Gichoya, Judy; Pearce, Chris; Wickramasinghe, Nilmini

    2013-01-01

    Kenya ranks among the twenty-two countries that collectively contribute about 80% of the world's Tuberculosis cases; with a 50-200 fold increased risk of tuberculosis in HIV infected persons versus non-HIV hosts. Contemporaneously, there is an increase in mobile penetration and its use to support healthcare throughout Africa. Many are skeptical that such m-health solutions are unsustainable and not scalable. We seek to design a scalable, pervasive m-health solution for Tuberculosis care to become a use case for sustainable and scalable health IT in limited resource settings. We combine agile design principles and user-centered design to develop the architecture needed for this initiative. Furthermore, the architecture runs on multiple devices integrated to deliver functionality critical for successful Health IT implementation in limited resource settings. It is anticipated that once fully implemented, the proposed m-health solution will facilitate superior monitoring and management of Tuberculosis and thereby reduce the alarming statistic regarding this disease in this region.

  4. OFF-DESIGN OPERATION OF IMPELLER OF THE CENTRIFUGAL COMPRESSOR

    Directory of Open Access Journals (Sweden)

    Saim KOÇAK

    2004-02-01

    Full Text Available Inducer and discharge dimensions of impellers of centrifugal compressor are determined as a preliminary design. Blockage factor and inducer dimensionless mass flow are exercised in relation with the relative Mach number. The equation which will be based o off-design calculation, related with the discharge relative Mach number are iterated until it will equal to inducer dimensionless mass flow rate. Then discharge relative Mach number for off-design works is obtained. The results calculated in accordance with pressure, temperature and density are seen to be similar with the theoretical parameters.

  5. Operation technology of the ventilation system of the radioactive waste treatment facility(II) - Design and operation note

    Energy Technology Data Exchange (ETDEWEB)

    Lee, K. M.; Lee, B. C.; Bae, S. M. [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-12-01

    As the radioactive waste treatment work, such as compaction and/or solidification of wastes, are done directly by the workers in the Radioactive Waste Treatment Facility, the reasonable design and operation of the ventilation system is essential. In this report, the design criteria and specification of the ventilation equipment, system operation method are described for the effective design and operation of ventilation system in the radioactive waste treatment facility. And the anti-vibration work which was done in the Radioactive Waste Treatment Facility in KAERI to reduce the effect of vibration due to the continuous operation of big rotational equipment, the intake fans and the exhaust fans, are described in the report. 11 refs., 10 figs., 12 tabs. (Author)

  6. Design and operation of evaporators for radioactive wastes

    International Nuclear Information System (INIS)

    Yamomoto, Y.

    1968-01-01

    A manual dealing with the application of evaporators to the treatment of liquid radioactive wastes. This book is the second of three commissioned by the IAEA on the three on the three principal techniques for concentrating radioactive wastes, namely chemical precipitation, evaporation and ion-exchange. Informations on different types of evaporators and related equipment and their operational procedures are given in this document. It also gives different means of disposal of evaporator condensates and concentrates and a rough estimate of costs of radioactive waste evaporator plant and its operation. 58 refs, 43 figs, 5 tabs

  7. Design and operation of evaporators for radioactive wastes

    Energy Technology Data Exchange (ETDEWEB)

    Yamomoto, Y [comp.; Tokyo Univ. (Japan)

    1968-05-01

    A manual dealing with the application of evaporators to the treatment of liquid radioactive wastes. This book is the second of three commissioned by the IAEA on the three on the three principal techniques for concentrating radioactive wastes, namely chemical precipitation, evaporation and ion-exchange. Informations on different types of evaporators and related equipment and their operational procedures are given in this document. It also gives different means of disposal of evaporator condensates and concentrates and a rough estimate of costs of radioactive waste evaporator plant and its operation. 58 refs, 43 figs, 5 tabs.

  8. The SPS Beam quality monitor, from design to operation

    CERN Document Server

    Papotti, G; Follin, F; Shaposhnikova, E

    2011-01-01

    The SPS Beam Quality Monitor is a system that monitors longitudinal beam parameters on a cycle-by-cycle basis and prevents extraction to the LHC in case the specifications are not met. This avoids losses, unnecessary stress of machine protection components and luminosity degradation, additionally helping efficiency during the filling process. The system has been operational since the 2009 LHC run, checking the beam pattern, its correct position with respect to the LHC references, individual bunch lengths and stability. In this paper the algorithms used, the hardware implementation and the operational aspects are presented.

  9. A comprehensive review of microbial electrolysis cells (MEC reactor designs and configurations for sustainable hydrogen gas production

    Directory of Open Access Journals (Sweden)

    Abudukeremu Kadier

    2016-03-01

    Full Text Available Hydrogen gas has tremendous potential as an environmentally acceptable energy carrier for vehicles. A cutting edge technology called a microbial electrolysis cell (MEC can achieve sustainable and clean hydrogen production from a wide range of renewable biomass and wastewaters. Enhancing the hydrogen production rate and lowering the energy input are the main challenges of MEC technology. MEC reactor design is one of the crucial factors which directly influence on hydrogen and current production rate in MECs. The rector design is also a key factor to up-scaling. Traditional MEC designs incorporated membranes, but it was recently shown that membrane-free designs can lead to both high hydrogen recoveries and production rates. Since then multiple studies have developed reactors that operate without membranes. This review provides a brief overview of recent advances in research on scalable MEC reactor design and configurations.

  10. Roadmap for Integrating Sustainable Design into Site-Level Operations

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, Keith L.; Dorsey, Judy A.

    2000-04-19

    Sustainable Design recognizes that products and processes are interdependent with the environmental, economic, and social systems surrounding them and implements measures to prevent an unsustainable compromise to these systems.

  11. REQUIREMENTS FOR DESIGN, EQUIPMENT AND OPERATION MODE OF TAXI VEHICLES

    Directory of Open Access Journals (Sweden)

    Norayr Oganesovich Bludyan

    2015-09-01

    Full Text Available The analysis of international experience in application of requirements for the taxi vehicles design and equipment. The approaches to improvement of cabbing have been defined by determination of requirements for taxi vehicles.

  12. The Preliminary Design and Fabrication of a Manually Operated ...

    African Journals Online (AJOL)

    A ten (10) tonnes capacity agro waste manual briquetting machine have been designed and fabricated using locally available materials. The machine principal parts are made of frame, compaction chamber and base plate . Compaction ...

  13. Work zone design and operation enhancements : final report, March 2010.

    Science.gov (United States)

    2010-02-01

    Oregon Department of Transportation contractors are required to implement Traffic Control Plans (TCPs) to protect and direct traffic through work zones. The design and implementation of TCPs have shown variation from project-to-project across the Sta...

  14. CODP Co operative design process - from urban strategy to detail

    OpenAIRE

    Thunberg, Pär; Philipson, Olof

    2012-01-01

    This project investigates the cooperation between architect and engineer. The context of the investigation is the design of buildings for a sustainable society. The goal of the project is to further the development of the sustainable built society by increasing the knowledge of the interdisciplinary cooperation between these two fields. The focus is a close cooperation already from the start of a project. By involving both fields in the early design stages it is thought that the knowledge and...

  15. Design and operation of Alvand II C tokamak

    International Nuclear Information System (INIS)

    Avakian, M.; Azodi, H.; Naraghi, M.; Tabatabaie, H.; Rezvani, B.; Shahnazi, Sh.; Behrozinia, J.; Solaimani, M.

    1984-01-01

    ALVAND IIC is a research tokamak having a circular cross section with major radius of 45.5 cm and minor radius of 12.6 cm, which has been designed and constructed in the plasma physics division of NRC of AEOI. It is used for developing various diagnostics for low beta plasmas and study of the physical characteristics of these plasmas. This paper discusses the design of ALVAND IIC. (Author)

  16. Towards testability in smart card operating system design

    NARCIS (Netherlands)

    Hartel, Pieter H.; Cordonnier, V.; de Jong, Eduard K.; Quisquater, J.J.

    1994-01-01

    The operating system of a smart card is a safety critical system. Distributed in millions, smart cards with their small 8-bit CPU support applications where transferred values are only protected by the strength of a cryptographic protocol. This strength goes no further than the implementation of the

  17. Optimal scope of supply chain network & operations design

    NARCIS (Netherlands)

    Ma, N.

    2014-01-01

    The increasingly complex supply chain networks and operations call for the development of decision support systems and optimization techniques that take a holistic view of supply chain issues and provide support for integrated decision-making. The economic impacts of optimized supply chain are

  18. Tactical/Operational Decision Making for Designing Green Logistics Networks

    NARCIS (Netherlands)

    I. Mallidis (Ioannis); R. Dekker (Rommert); D. Vlachos (Dimitrios)

    2013-01-01

    textabstractCap and trade regulations along with an increasing consumer and company demand for green products and services constitute two major drivers for motivating corporations to adopt green practices. However, the adoption of such practices usually increases their operational costs. Therefore,

  19. Design Optimisation and Conrol of a Pilot Operated Seat Valve

    DEFF Research Database (Denmark)

    Nielsen, Brian; Andersen, Torben Ole; Hansen, Michael Rygaard

    2004-01-01

    The paper gives an approach for optimisation of the bandwidth of a pilot operated seat valve for mobile applications. Physical dimensions as well as parameters of the implemented control loop are optimised simultaneously. The frequency response of the valve varies as a function of the pressure drop...

  20. 40 CFR 264.301 - Design and operating requirements.

    Science.gov (United States)

    2010-07-01

    ... that is not located completely above the seasonal high water table must demonstrate that the operation... subsurface soil or ground water or surface water at anytime during the active life (including the closure... waste or leachate to which they are exposed, climatic conditions, the stress of installation, and the...

  1. Data-driven architectural design to production and operation

    NARCIS (Netherlands)

    Bier, H.H.; Mostafavi, S.

    2015-01-01

    Data-driven architectural production and operation explored within Hyperbody rely heavily on system thinking implying that all parts of a system are to be understood in relation to each other. These relations are established bi-directionally so that data-driven architecture is not only produced

  2. Operations Management in the Design and Execution of MBA Programs

    Science.gov (United States)

    Busing, Michael E.; Palocsay, Susan W.

    2016-01-01

    Master of business administration (MBA) programs are under intense pressure to improve efficiencies, lower tuition, and offer refreshed curriculum that is of high quality and regarded as relevant by the marketplace. In light of this environment, the authors propose a conceptual framework for effectively employing operations management (OM)…

  3. 40 CFR 265.443 - Design and operating requirements.

    Science.gov (United States)

    2010-07-01

    ... standards established by professional organizations generally recognized by industry such as the American Concrete Institute (ACI) and the American Society of Testing Materials (ASTM) in judging the structural..., climatic conditions, the stress of installation, and the stress of daily operations, e.g., variable and...

  4. 40 CFR 264.573 - Design and operating requirements.

    Science.gov (United States)

    2010-07-01

    ... professional organizations generally recognized by the industry such as the American Concrete Institute (ACI) or the American Society of Testing and Materials (ASTM) in judging the structural integrity..., climatic conditions, the stress of daily operations, e.g., variable and moving loads such as vehicle...

  5. Recommended Practices for the Safe Design and Operation of Flywheels

    Energy Technology Data Exchange (ETDEWEB)

    Bender, Donald Arthur [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-12-01

    Flywheel energy storage systems are in use globally in increasing numbers . No codes pertaining specifically to flywheel energy storage exist. A number of industrial incidents have occurred. This protocol recommends a technical basis for safe flywheel de sign and operation for consideration by flywheel developers, users of flywheel systems and standards setting organizations.

  6. Steam boilers : Process models for improved operation and design

    NARCIS (Netherlands)

    Ahnert, F.

    2007-01-01

    Biomass combustion can be an economic way to contribute to the reduction of CO2 emissions, which are a main suspect of the so-called greenhouse effect. In order to promote a widespread utilization of biomass combustion, operational problems like fuel treatment, slagging, fouling and corrosion have

  7. Basic national requirements for safe design, construction and operation

    International Nuclear Information System (INIS)

    Franzen, L.F.

    1980-01-01

    Nuclear power plants have to be save. Vendors and utilities operating such plants, are convinced that their plants meet this requirement. Who, however, is establishing the safety requirements to be met by those manufacturing and operating nuclear power plants. What are the mechanisms to control whether the features provided assure the required safety level. Who controls whether the required and planned safety features are really provided. Who is eventually responsible for assuring safety after commissioning of a nuclear power plant. These fundamental questions being raised in many discussions on safety and environmental protection are dealt with in the following sections: (1) Fundamental safety requirements on nuclear power plants, in which such items as risk, legal bases and licensing procedure are discussed, (2) Surveillance during construction, in which safety analysis report, siting, safety evaluation, document examination, quality assurance, and commissioning testing are dealt with, (3) Operating tests and conditions in which recurrent inspections, environmental protection during operation, investigation of abnormal occurences and backfitting requirements as reviewed, and (4) Safety philosophy and safety policy to conclude this presentation. The German approach to nuclear safety serves as an example for an effective way of assuring safe nuclear power. (orig.)

  8. Designing for Wide-Area Situation Awareness in Future Power Grid Operations

    Science.gov (United States)

    Tran, Fiona F.

    Power grid operation uncertainty and complexity continue to increase with the rise of electricity market deregulation, renewable generation, and interconnectedness between multiple jurisdictions. Human operators need appropriate wide-area visualizations to help them monitor system status to ensure reliable operation of the interconnected power grid. We observed transmission operations at a control centre, conducted critical incident interviews, and led focus group sessions with operators. The results informed a Work Domain Analysis of power grid operations, which in turn informed an Ecological Interface Design concept for wide-area monitoring. I validated design concepts through tabletop discussions and a usability evaluation with operators, earning a mean System Usability Scale score of 77 out of 90. The design concepts aim to support an operator's complete and accurate understanding of the power grid state, which operators increasingly require due to the critical nature of power grid infrastructure and growing sources of system uncertainty.

  9. Design and Operation of the Transformed National Healthy Start Evaluation.

    Science.gov (United States)

    Banks, Jamelle E; Dwyer, Maura; Hirai, Ashley; Ghandour, Reem M; Atrash, Hani K

    2017-12-01

    Purpose Improving pregnancy outcomes for women and children is one of the nation's top priorities. The Healthy Start (HS) program was created to address factors that contribute to high infant mortality rates (IMRs) and persistent disparities in IMRs. The program began in 1991 and was transformed in 2014 to apply lessons from emerging research, past evaluation findings, and expert recommendations. To understand the implementation and impact of the transformed program, there is a need for a robust and comprehensive evaluation. Description The national HS evaluation will include an implementation evaluation, which will describe program components that affect outcomes; a utilization evaluation, which will examine the characteristics of women and infants who did and did not utilize the program; and an outcome evaluation, which will assess the program's effectiveness with regard to producing expected outcomes among the target population. Data sources include the National HS Program Survey, a HS participant survey, and individual-level program data linked to vital records and the Pregnancy Risk Assessment Monitoring System (PRAMS) survey. Assessment Descriptive analyses will be used to examine differences in risk profiles between participants and non-participants, as well as to calculate penetration rates for high-risk women in respective service areas. Multivariable analyses will be used to determine the impact of the program on key outcomes and will explore variation by dose, type of services received, and grantee characteristics. Conclusion Evaluation findings are expected to inform program decisions and direction, including identification of effective program components that can be spread and scaled.

  10. Design, fabrication and operation of the LVDT based vertical dilatometer

    International Nuclear Information System (INIS)

    Manoj, N.; Kerkar, A.S.; Mathews, M.D.; Gautam, J.K.; Tyagi, A.K.; Thomas, K.C.

    2005-07-01

    This report provides the details of a dilatometer developed in-house to measure thermal expansion from room temperature to 1173 K. The instrument was designed, fabricated and tested for its satisfactory performance by analyzing the thermal expansion properties of several materials up to a maximum temperature of 1123 K. One of the important feature in this design is that, the instrument has been fabricated by using all indigenously available components. The sample loading and initial zero adjustment procedure has been made very simple in this design. The software for furnace temperature programming and control, data collection, data processing and plotting of the graph has also been developed. Provision for carrying out the measurements in vacuum as well as flowing gas have been provided. (author)

  11. Moderator purification and design modifications based on operation feedback

    Energy Technology Data Exchange (ETDEWEB)

    Das, S; Chakrabarti, A K; Shirolkar, K M; Sharma, V K [Nuclear Power Corporation, Bhabha Atomic Research Centre, Mumbai (India)

    1994-06-01

    Heavy water is used as a moderator in the Pressurized Heavy Water Reactors using natural uranium as a fissile fuel. The purification system is provided to maintain the purity of moderator heavy water so as to minimise the radiolytic decomposition of heavy water due to nuclear radiation which otherwise would lead to hazardous concentration of deuterium in the moderator cover gas. The presence of dissolved impurity in the moderator increases the radiolysis rate by impeding the reverse reaction and hence these must be removed. The purification system in general controls the chemistry of moderator by minimizing the corrosion of piping in the circuit and along with the liquid poison injection system adjusts the concentration of the poisons in the moderator. This paper describes the evolution of the purification system for the 500 MWe PHWRs based on various operating requirements and feedback from the operating stations. (author). 2 refs., 3 figs., 1 tab.

  12. Hydraulic screw fastening devices - design, maintenance, operational experience

    International Nuclear Information System (INIS)

    Lachner.

    1976-01-01

    With hydraulic screw fastening devices, pretension values with a maximum deviation of +-2.5% from the rated value can be achieved. This high degree of pretension accuracy is of considerable importance with regard to the safety factor required for the screw connection between reactor vessel head and reactor vessel. The operating rhythm of a nuclear power station with its refuelling art regular intervals makes further demands on the screw fastening device, in particular in connection with the transport of screws and for nuts. The necessary installations extend the screw fastening device into a combination of a high-pressure hydraulic cylinder system with an electrical or pneumoelectrical driving unit and an electrical control unit. Maintenance work is complicated by the large number of identical, highly stressed structural elements in connection with an unfavourable relation operating time/outage time. The problems have been perpetually reduced by close cooperation between the manufacturers and users of screw fastening devices. (orig./AK) [de

  13. Moderator purification and design modifications based on operation feedback

    International Nuclear Information System (INIS)

    Das, S.; Chakrabarti, A.K.; Shirolkar, K.M.; Sharma, V.K.

    1994-01-01

    Heavy water is used as a moderator in the Pressurized Heavy Water Reactors using natural uranium as a fissile fuel. The purification system is provided to maintain the purity of moderator heavy water so as to minimise the radiolytic decomposition of heavy water due to nuclear radiation which otherwise would lead to hazardous concentration of deuterium in the moderator cover gas. The presence of dissolved impurity in the moderator increases the radiolysis rate by impeding the reverse reaction and hence these must be removed. The purification system in general controls the chemistry of moderator by minimizing the corrosion of piping in the circuit and along with the liquid poison injection system adjusts the concentration of the poisons in the moderator. This paper describes the evolution of the purification system for the 500 MWe PHWRs based on various operating requirements and feedback from the operating stations. (author)

  14. Design and operation of remote maintenance systems in JET

    International Nuclear Information System (INIS)

    Raimondi, T.

    1987-01-01

    The JET tokamak is a joint European project aimed at proving the viability of nuclear fusion as a source of energy. A remote handling system is being developed for this large experimental facility. Force feedback servomanipulators and TV cameras are positioned at work locations by large transporters. Positioning and tele-operation are computer-assisted. Special tools are being devised to facilitate difficult tasks

  15. Optimizing Biorefinery Design and Operations via Linear Programming Models

    Energy Technology Data Exchange (ETDEWEB)

    Talmadge, Michael; Batan, Liaw; Lamers, Patrick; Hartley, Damon; Biddy, Mary; Tao, Ling; Tan, Eric

    2017-03-28

    The ability to assess and optimize economics of biomass resource utilization for the production of fuels, chemicals and power is essential for the ultimate success of a bioenergy industry. The team of authors, consisting of members from the National Renewable Energy Laboratory (NREL) and the Idaho National Laboratory (INL), has developed simple biorefinery linear programming (LP) models to enable the optimization of theoretical or existing biorefineries. The goal of this analysis is to demonstrate how such models can benefit the developing biorefining industry. It focuses on a theoretical multi-pathway, thermochemical biorefinery configuration and demonstrates how the biorefinery can use LP models for operations planning and optimization in comparable ways to the petroleum refining industry. Using LP modeling tools developed under U.S. Department of Energy's Bioenergy Technologies Office (DOE-BETO) funded efforts, the authors investigate optimization challenges for the theoretical biorefineries such as (1) optimal feedstock slate based on available biomass and prices, (2) breakeven price analysis for available feedstocks, (3) impact analysis for changes in feedstock costs and product prices, (4) optimal biorefinery operations during unit shutdowns / turnarounds, and (5) incentives for increased processing capacity. These biorefinery examples are comparable to crude oil purchasing and operational optimization studies that petroleum refiners perform routinely using LPs and other optimization models. It is important to note that the analyses presented in this article are strictly theoretical and they are not based on current energy market prices. The pricing structure assigned for this demonstrative analysis is consistent with $4 per gallon gasoline, which clearly assumes an economic environment that would favor the construction and operation of biorefineries. The analysis approach and examples provide valuable insights into the usefulness of analysis tools for

  16. Scaffolding and co-operative learning : Effects on reading comprehension and vocabulary knowledge in English as a foreign language

    NARCIS (Netherlands)

    Wachyunni, Sri

    2015-01-01

    For university students in Indonesia, English reading comprehension, which partially depends on vocabulary knowledge, is key to success in academic achievement. The current study was set up to compare the effect of two commonly known teaching interventions during a whole semester to improve reading

  17. Twelve-year follow-up of a randomized controlled trial of comprehensive physiotherapy following disc herniation operation.

    Science.gov (United States)

    Ebenbichler, Gerold R; Inschlag, Silke; Pflüger, Verena; Stemberger, Regina; Wiesinger, Günther; Novak, Klaus; Christoph, Krall; Resch, Karl L

    2015-06-01

    To evaluate the long-term effects of postoperative comprehensive physiotherapy starting one week after lumbar disc surgery. Twelve-year follow-up of a three-armed, randomized, controlled, single-blinded clinical trial. Department of Physical Medicine & Rehabilitation. Of 111 patients following first-time, uncomplicated lumbar disc surgery who participated in the original study and completed the treatment originally allocated, 74 ((67%; 29 (73%) physiotherapy, 22 (58%) sham therapy, 23 (68%) no therapy) completed a 12-year follow-up examination. In the original study, patients had been randomly assigned to comprehensive physiotherapy, sham intervention (neck massage), or no therapy. Low Back Pain Rating Scale; best score 0, worst score 130 points). At 12 years after surgery, the group participating in comprehensive physiotherapy had significantly better functional outcomes, as rated on the Low Back Pain Rating Score, than the untreated group (mean difference: -13.2 (95% CI: (-25.4; -1.0)). Equally, there was a clinically relevant, non-significant difference between the sham therapy and no therapy (mean difference: -12.5 (95%CI: -26.1; 1.1)). Consequently, the Low Back Pain Rating Score outcome did not differ between physiotherapy and sham therapy (mean difference: -0.7 (95%CI: -14.2; 12.8)). Participating in a comprehensive physiotherapy program following lumbar disc surgery may be associated with better long-term health benefits over no intervention, but may not be superior to sham therapy. © The Author(s) 2014.

  18. 20 CFR 662.430 - Under what conditions may One-Stop operators designated to operate in a One-Stop delivery system...

    Science.gov (United States)

    2010-04-01

    ... designated to operate in a One-Stop delivery system established prior to the enactment of WIA be designated... DESCRIPTION OF THE ONE-STOP SYSTEM UNDER TITLE I OF THE WORKFORCE INVESTMENT ACT One-Stop Operators § 662.430 Under what conditions may One-Stop operators designated to operate in a One-Stop delivery system...

  19. Joint Optimal Design and Operation of Hybrid Energy Storage Systems

    NARCIS (Netherlands)

    Y. Ghiassi-Farrokhfal (Yashar); C. Rosenberg; S. Keshav (Srinivasam); M.-B. Adjaho (Marie-Benedicte)

    2016-01-01

    markdownabstractThe wide range of performance characteristics of storage technologies motivates the use of a hybrid energy storage systems (HESS) that combines the best features of multiple technologies. However, HESS design is complex, in that it involves the choice of storage technologies, the

  20. design and operations challenges of a single toggle jaw crusher

    African Journals Online (AJOL)

    HOD

    [13] showed that the difference between Wall and Bond energies for hard rocks are .... advantages of retaining the structural design of the crusher and decreasing the ..... of aw crusher supporting structure fatigue failure”,. Stro niški Vestnik ...

  1. Programming biological operating systems: genome design, assembly and activation.

    Science.gov (United States)

    Gibson, Daniel G

    2014-05-01

    The DNA technologies developed over the past 20 years for reading and writing the genetic code converged when the first synthetic cell was created 4 years ago. An outcome of this work has been an extraordinary set of tools for synthesizing, assembling, engineering and transplanting whole bacterial genomes. Technical progress, options and applications for bacterial genome design, assembly and activation are discussed.

  2. Design and development of high voltage high power operational ...

    Indian Academy of Sciences (India)

    address this challenge, a) Designing a discrete power opamp with high .... the use of high-impedance feedback networks, thus minimizing their output loading ... Spice simulation is done for the circuit and results are given in figures 4a–c.

  3. Lessons from sexual and reproductive health voucher program design and function: a comprehensive review

    Science.gov (United States)

    2014-01-01

    Background Developing countries face challenges in financing healthcare; often the poor do not receive the most basic services. The past decade has seen a sharp increase in the number of voucher programs, which target output-based subsidies for specific services to poor and underserved groups. The dearth of literature that examines lessons learned risks the wheel being endlessly reinvented. This paper examines commonalities and differences in voucher design and implementation, highlighting lessons learned for the design of new voucher programmes. Methodology The methodology comprised: discussion among key experts to develop inclusion/exclusion criteria; up-dating the literature database used by the DFID systematic review of voucher programs; and networking with key contacts to identify new programs and obtain additional program documents. We identified 40 programs for review and extracted a dataset of more than 120 program characteristics for detailed analysis. Results All programs aimed to increase utilisation of healthcare, particularly maternal health services, overwhelmingly among low-income populations. The majority contract(ed) private providers, or public and private providers, and all facilitate(d) access to services that are well defined, time-limited and reflect the country’s stated health priorities. All voucher programs incorporate a governing body, management agency, contracted providers and target population, and all share the same incentive structure: the transfer of subsidies from consumers to service providers, resulting in a strong effect on both consumer and provider behaviour. Vouchers deliver subsidies to individuals, who in the absence of the subsidy would likely not have sought care, and in all programs a positive behavioural response is observed, with providers investing voucher revenue to attract more clients. A large majority of programs studied used targeting mechanisms. Conclusions While many programs remain too small to address

  4. Lessons from sexual and reproductive health voucher program design and function: a comprehensive review.

    Science.gov (United States)

    Grainger, Corinne; Gorter, Anna; Okal, Jerry; Bellows, Ben

    2014-04-29

    Developing countries face challenges in financing healthcare; often the poor do not receive the most basic services. The past decade has seen a sharp increase in the number of voucher programs, which target output-based subsidies for specific services to poor and underserved groups. The dearth of literature that examines lessons learned risks the wheel being endlessly reinvented. This paper examines commonalities and differences in voucher design and implementation, highlighting lessons learned for the design of new voucher programmes. The methodology comprised: discussion among key experts to develop inclusion/exclusion criteria; up-dating the literature database used by the DFID systematic review of voucher programs; and networking with key contacts to identify new programs and obtain additional program documents. We identified 40 programs for review and extracted a dataset of more than 120 program characteristics for detailed analysis. All programs aimed to increase utilisation of healthcare, particularly maternal health services, overwhelmingly among low-income populations. The majority contract(ed) private providers, or public and private providers, and all facilitate(d) access to services that are well defined, time-limited and reflect the country's stated health priorities. All voucher programs incorporate a governing body, management agency, contracted providers and target population, and all share the same incentive structure: the transfer of subsidies from consumers to service providers, resulting in a strong effect on both consumer and provider behaviour. Vouchers deliver subsidies to individuals, who in the absence of the subsidy would likely not have sought care, and in all programs a positive behavioural response is observed, with providers investing voucher revenue to attract more clients. A large majority of programs studied used targeting mechanisms. While many programs remain too small to address national-level need among the poor, large programs

  5. Design of Adaptive Organizations for Effects Based Operations

    Science.gov (United States)

    2009-04-04

    and one for type B. 57 Threat. <Sy<K^» TBM^I SdSQi jɛw» la** Fore* HHO System S| • -SrtN*i»-- R*l*i Sitt | AN/MIS € L / t.Ji.ii...Activity Diagram (OV-5). 58 • Operational Node • HHO HEMS SfftM ^mniarvl Control Intercept / ISiU« \\ \\ Au^honratioin./’ \\Fly (mto AORp ;^B...Assess Kill () Intercept Status Intercept ID int Intercept Node Intercept ID: int ThreatID: int HHO • Authorization t IssueAuthonzation (I

  6. Design and operation of the emergency support center, CAE

    International Nuclear Information System (INIS)

    Caro, R. J.; Lopez Trillo, E.

    2016-01-01

    The enhancements developed in Spain in the area of Emergency Management, as consequence of the accident at the Fukushima Dai-Ichi NPP in 2011, included the definition of new emergency response centers; Alternative Center for Emergency Management (CAGE) on each NPP and the Emergency Support Center (CAE), shared by all NPPs. This article summarizes the main features and operation activities undertaken since the establishment of the new CAE, centralized, external to the NPPs shared by all Spanish plants and managed by Tecnatom. (Author)

  7. A comprehensive guide for designing more efficient irrigation systems with respect to application control

    Science.gov (United States)

    Khaddam, Issam; Schuetze, Niels

    2017-04-01

    The worldwide water scarcity problems are expected to aggravate due to the increasing population and the need to produce more food. Irrigated agriculture is considered the highest consumer of fresh water resources with a rate exceeds 70% of global consumption. Consequently, an improvement in the efficiency of all irrigation methods, such as furrow or drip irrigation, becomes more necessary and urgent. Therefore, a more precise knowledge about soil water distribution in the root zone and the water balance components is required. For this purpose and as a part of the SAPHIR project (Saxonian Platform for high Performance Irrigation), a 2D simulation- based study was performed with virtual field conditions. The study investigates the most important design parameters of many irrigation systems, such as irrigation intensity and duration, and shows there influence on the water distribution efficiency. Furthermore, three main soil textures are used to test the impact of the soil hydraulic properties on irrigation effectiveness. A numerous number of irrigation scenarios of each irrigation system was simulated using HYDRUS 2D. Thereafter, the results were digitally calculated, compiled and made available online in the so called "Irrigation Atlases". The irrigation atlases provide graphical results of the soil moisture and pressure head distributions in the root zone. Moreover, they contain detailed information of the water balance for all simulated scenarios. The most studies evaluate the irrigation water demands on local, regional or global scales and for that an efficient water distribution is required. In this context, the irrigation atlases can serve as a valuable tool for the implementation of planned irrigation measures.

  8. Succinate overproduction: A case study of computational strain design using a comprehensive Escherichia coli kinetic model

    Directory of Open Access Journals (Sweden)

    Ali eKhodayari

    2015-01-01

    Full Text Available Computational strain design prediction accuracy has been the focus for many recent efforts through the selective integration of kinetic information into metabolic models. In general, kinetic model prediction quality is determined by the range and scope of genetic and/or environmental perturbations used during parameterization. In this effort, we apply the k-OptForce procedure on a kinetic model of E. coli core metabolism constructed using the Ensemble Modeling (EM method and parameterized using multiple mutant strains data under aerobic respiration with glucose as the carbon source. Minimal interventions are identified that improve succinate yield under both aerobic and anaerobic conditions to test the fidelity of model predictions under both genetic and environmental perturbations. Under aerobic condition, k-OptForce identifies interventions that match existing experimental strategies pointing at a number of unexplored flux redirections such as routing glyoxylate flux through the glycerate metabolism to improve succinate yield. Many of the identified interventions rely on the kinetic descriptions and would not be discoverable by a purely stoichiometric description. In contrast, under fermentative (anaerobic conditions, k-OptForce fails to identify key interventions including up-regulation of anaplerotic reactions and elimination of competitive fermentative products. This is due to the fact that the pathways activated under anaerobic conditions were not properly parameterized as only aerobic flux data were used in the model construction. This study shed light on the importance of condition-specific model parameterization and provides insight onto how to augment kinetic models so as to correctly respond to multiple environmental perturbations.

  9. Nd:YAG Laser Firmware Design under RTOS Operation

    Energy Technology Data Exchange (ETDEWEB)

    Kim, B. G.; Kim, W. Y.; Park, G. R.; Moon, D. S.; Hong, J. H.; Kim, H. J.; Cho, J. S. [Pusan National University (Korea)

    2000-07-01

    A pulsed Nd:YAG laser is used widely for materials processing and medical instrument. It's very important to control the laser energy density in those fields using a pulsed Nd:YAG laser. A pulse repetition rate and a pulse width are regarded as the most dominant factors to control the energy density of laser beam. In this paper, the alternating charge and discharge system was designed to adjust a pulse repetition rate. This system is controlled by microprocessor and allows to replace an expensive condenser for high frequency to cheap one of low frequency. In addition, The microcontroller monitors the flow of cooling water, short circuit, and miss firing and so on. We designed Nd:YAG laser firmware with smart microcontroller, and want to explain general matters about the firmware from now. (author). 8 refs., 6 figs.

  10. Design considerations and operational performance of Anaerobic Digester: A Review

    Directory of Open Access Journals (Sweden)

    Muzaffar Ahmad Mir

    2016-04-01

    Full Text Available Due to the decline in fossil fuel reservoirs, the researchers emphasized more on the production of biogas from organic waste. Producing the renewable energy from biodegradable waste helps to overcome the energy crisis and solid waste management, done by anaerobic digestion. Anaerobic digestion is controlled breakdown of organic matter into methane gas (60%, carbon dioxide (40%, trace components along with digested used as soil conditioner. However there is vast dearth of literature regarding the design considerations. The batch digestion system yields a cost-effective and economically viable means for conversion of the food waste to useful energy. It is therefore recommended that such process can be increasingly employed in order to get and simultaneously protect the environment .This paper aims to draw key analysis and concern about the design considerations, analysis of gas production, substrates and inoculums utilization, uses and impacts of biogas.

  11. Assessment of alternative vessel and blanket design on ITER operation

    Energy Technology Data Exchange (ETDEWEB)

    Cavinato, M., E-mail: mario.cavinato@f4e.europa.e [FUSION FOR ENERGY Joint Undertaking, 08019 Barcelona (Spain); Portone, A.; Saibene, G.; Sartori, R. [FUSION FOR ENERGY Joint Undertaking, 08019 Barcelona (Spain); Albanese, R.; Ambrosino, G.; Ariola, M. [Associazione Euratom-ENEA-CREATE, DIMET, Universita degli Studi di Napoli (Italy); Artaserse, G. [Associazione Euratom-ENEA-CREATE, DIMET, Universita degli Studi di Reggio Calabria (Italy); Mattei, M. [Associazione Euratom-ENEA-CREATE, DIAM, Seconda Universita di Napoli, Via Roma 29, Aversa, CE 81031 Italy (Italy); Pironti, A. [Associazione Euratom-ENEA-CREATE, DIMET, Universita degli Studi di Napoli (Italy); Villone, F. [Associazione Euratom-ENEA-CREATE, DIMET, Universita degli Studi di Cassino (Italy)

    2010-12-15

    In the framework of the ITER project, an investigation has been conducted on an alternative vessel and blanket design, aimed at reducing cost and production risk. The modifications proposed have a strong impact on plasma control since they affect the main conducting structures surrounding the plasma column, providing passive stabilization but at the same time shielding the field generated by the active coils to control the plasma motion and shape. An extensive analysis was performed to assess the plasma vertical controllability and the modified requirements to the in-vessel vertical stability coils system as well as to the external Poloidal Field coils system. A similar analysis was aimed at assessing the performance of the shape control system in presence of the modified structures. The effect on plasma breakdown was also evaluated in terms of maximum initial loop voltage, quality of magnetic null and the flux loss related to the breakdown delay that was quantified under the same hypothesis employed by ITER for the baseline design. Furthermore, the modified design presents issues for the magnetic diagnostic system, related to the shielding of the probes by the eddy currents, which were analysed with a 3D model. The results of the analyses performed have some general interest in particular regarding the influence on plasma stability of 3D structures with close proximity to the plasma. The present paper aims at giving an overview of the analyses that have been carried out and a summary of the results in terms of impact of the modified design on plasma control and scenario, and in general an evaluation of the role of passive structure in plasma vertical stability and shape control.

  12. Design and operation of a biomagnetic multichannel system

    International Nuclear Information System (INIS)

    Schneider, S.; Seifert, H.; Reichenberger, H.; Hoenig, H.E.

    1992-01-01

    This paper describes the design and optimization of the KRENIKON system for the measurement of magnetic fields of the brain and the heart. Aspects for the configuration of the sensor array are discussed. Special emphasis is given to the suppression of interferences by a combination of magnetic shielding with first-order gradiometers and to the construction of the gradiometer array in foil technology. (orig.)

  13. Network Design Guidance for the Global Special Operations Forces Network

    Science.gov (United States)

    2014-12-01

    an introduction to the Network Design Continuum. 170 Robert M. Hayden, “ Moral Vision and Impaired Insight: The Imagining of Other Peoples...CEO and municipal president were of an abstract nature, about moral courage and political principles, which he felt it was the task of the UN to...the actions needled to improv e or rorrect peri:lrmance, relativ e to the goals of the syste m. Determin ing how a system shoukl WJrk and how dlanges

  14. Thermal, operational, and economic aspects of repository design alternatives

    International Nuclear Information System (INIS)

    Closs, K.D.; Papp, R.; Bechthold, W.; Engelmann, H.J.; Hartje, B.

    1989-01-01

    This paper discusses how a broad spectrum of heat-generating nuclear waste types like reprocessing waste (HLW, ILW), spent LWR, and spent HTR fuel will be disposed of in a future German repository located in a salt dome. Different package and emplacement concepts for the various waste forms are feasible, ranging from pure borehole emplacement of canisters and drums to pure drift emplacement of heavily shielded casks as well as combinations of both concepts. Optimization of the whole back-end system (waste treatment, interim storage, and disposal) is performed taking into account thermal, operational, and economic aspects. From a radiological viewpoint, the drift emplacement concept is superior to all concepts in as much as the occupational dose is lowest and zero release from the casks is attainable during normal and anomalous repository operation. As far as economics are concerned, the cost of the heavily shielded casks necessary for drift emplacement contributes markedly to the overall cost of the whole back-end system. Drift emplacement can compete economically with the other concepts only if the casks are used both for interim storage and disposal

  15. Multi-operation cryptographic engine: VLSI design and implementation

    International Nuclear Information System (INIS)

    Selimis, George; Koufopavlou, Odysseas

    2005-01-01

    The environment of smart card lacks of system resources but the commercial and economic transactions via smart cards demand the use of certificated and secure cryptographic methods. In this paper a cryptographic approach in hardware for smart cards is proposed. The proposed system supports two basic operations of cryptography, authentication and encryption. The basic component of system is the one round of DES algorithm which supports the DES, Triple DES and the ANSI X9.17 standards. The proposed system is efficient in terms of area resources and techniques for low power consumption have applied. Due to the fact that the system is for smart card applications the overall throughput outperforms the typical smart card throughput standards

  16. Wind Power Plants Fundamentals, Design, Construction and Operation

    CERN Document Server

    Twele, Jochen

    2012-01-01

    Wind power plants teaches the physical foundations of usage of Wind Power. It includes the areas like Construction of Wind Power Plants, Design, Development of Production Series, Control, and discusses the dynamic forces acting on the systems as well as the power conversion and its connection to the distribution system. The book is written for graduate students, practitioners and inquisitive readers of any kind. It is based on lectures held at several universities. Its German version it already is the standard text book for courses on Wind Energy Engineering but serves also as reference for practising engineers.

  17. ANL small-sample calorimeter system design and operation

    International Nuclear Information System (INIS)

    Roche, C.T.; Perry, R.B.; Lewis, R.N.; Jung, E.A.; Haumann, J.R.

    1978-07-01

    The Small-Sample Calorimetric System is a portable instrument designed to measure the thermal power produced by radioactive decay of plutonium-containing fuels. The small-sample calorimeter is capable of measuring samples producing power up to 32 milliwatts at a rate of one sample every 20 min. The instrument is contained in two packages: a data-acquisition module consisting of a microprocessor with an 8K-byte nonvolatile memory, and a measurement module consisting of the calorimeter and a sample preheater. The total weight of the system is 18 kg

  18. A proposal for a comprehensive risk scoring system for predicting postoperative complications in octogenarian patients with medically operable lung cancer: JACS1303.

    Science.gov (United States)

    Saji, Hisashi; Ueno, Takahiko; Nakamura, Hiroshige; Okumura, Norihito; Tsuchida, Masanori; Sonobe, Makoto; Miyazaki, Takuro; Aokage, Keiju; Nakao, Masayuki; Haruki, Tomohiro; Ito, Hiroyuki; Kataoka, Kazuhiko; Okabe, Kazunori; Tomizawa, Kenji; Yoshimoto, Kentaro; Horio, Hirotoshi; Sugio, Kenji; Ode, Yasuhisa; Takao, Motoshi; Okada, Morihito; Chida, Masayuki

    2018-04-01

    Although some retrospective studies have reported clinicopathological scoring systems for predicting postoperative complications and survival outcomes for elderly lung cancer patients, optimized scoring systems remain controversial. The Japanese Association for Chest Surgery (JACS) conducted a nationwide multicentre prospective cohort and enrolled a total of 1019 octogenarians with medically operable lung cancer. Details of the clinical factors, comorbidities and comprehensive geriatric assessment were recorded for 895 patients to develop a comprehensive risk scoring (RS) system capable of predicting severe complications. Operative (30 days) and hospital mortality rates were 1.0% and 1.6%, respectively. Complications were observed in 308 (34%) patients, of whom 81 (8.4%) had Grade 3-4 severe complications. Pneumonia was the most common severe complication, observed in 27 (3.0%) patients. Five predictive factors, gender, comprehensive geriatric assessment75: memory and Simplified Comorbidity Score (SCS): diabetes mellitus, albumin and percentage vital capacity, were identified as independent predictive factors for severe postoperative complications (odds ratio = 2.73, 1.86, 1.54, 1.66 and 1.61, respectively) through univariate and multivariate analyses. A 5-fold cross-validation was performed as an internal validation to reconfirm these 5 predictive factors (average area under the curve 0.70). We developed a simplified RS system as follows: RS = 3 (gender: male) + 2 (comprehensive geriatric assessment 75: memory: yes) + 2 (albumin: <3.8 ng/ml) + 1 (percentage vital capacity: ≤90) + 1 (SCS: diabetes mellitus: yes). The current series shows that octogenarians can be successfully treated for lung cancer with surgical resection with an acceptable rate of severe complications and mortality. We propose a simplified RS system to predict severe complications in octogenarian patients with medically operative lung cancer. JACS1303 (UMIN000016756).

  19. 78 FR 59981 - Proposed Revision to Physical Security-Standard Design Certification and Operating Reactors

    Science.gov (United States)

    2013-09-30

    ... Design Certification and Operating Reactors AGENCY: Nuclear Regulatory Commission. ACTION: Standard... Design Certification and Operating Reactors.'' The NRC seeks comments on the proposed revised section of... subject): Federal Rulemaking Web site: Go to http://www.regulations.gov and search for Docket ID NRC-2013...

  20. Navigation and Alignment Aids Concept of Operations and Supplemental Design Information. Revision A

    Science.gov (United States)

    Kelly, Sean M.; Cryan, Scott P.

    2016-01-01

    The IDSS Navigation and Alignment Aids Concept of Operations and Supplemental Design Information document provides supplemental information to the IDSS IDD. The guide provides insight into the navigation and alignment aids design, and how those aids can be utilized by incoming vehicles for proximity operations and docking. The navigation aids are paramount to successful docking.

  1. Design/Operations review of core sampling trucks and associated equipment

    International Nuclear Information System (INIS)

    Shrivastava, H.P.

    1996-01-01

    A systematic review of the design and operations of the core sampling trucks was commissioned by Characterization Equipment Engineering of the Westinghouse Hanford Company in October 1995. The review team reviewed the design documents, specifications, operating procedure, training manuals and safety analysis reports. The review process, findings and corrective actions are summarized in this supporting document

  2. Design, development and operating experience with wet steam turbines

    International Nuclear Information System (INIS)

    Bolter, J.R.

    1989-01-01

    The paper first describes the special characteristics of wet steam units. It then goes on to discuss the principal features of the units manufactured by the author's company, the considerations on which the designs were based, and the development work carried out to validate them. Some of the design features such as the separator/reheater units and the arrangements for water extraction in the high pressure turbine are unconventional. An important characteristic of all nuclear plant is the combination of high capital cost and low fuel cost, and the consequent emphasis placed on high availability. The paper describes some service problems experienced with wet steam plant and how these were overcome with minimum loss of generation. The paper also describes a number of the developments for future wet steam plant which have evolved from these experiences, and from research and development programmes aimed at increasing the efficiency and reliability of both conventional and wet steam units. Blading, rotor construction and separator/reheater units are considered. (author)

  3. Advanced, Low/Zero Emission Boiler Design and Operation

    Energy Technology Data Exchange (ETDEWEB)

    Babcock/Wilcox; Illinois State Geological; Worley Parsons; Parsons Infrastructure/Technology Group

    2007-06-30

    In partnership with the U.S. Department of Energy's National Energy Technology Laboratory, B&W and Air Liquide are developing and optimizing the oxy-combustion process for retrofitting existing boilers as well as new plants. The main objectives of the project is to: (1) demonstrate the feasibility of the oxy-combustion technology with flue gas recycle in a 5-million Btu/hr coal-fired pilot boiler, (2) measure its performances in terms of emissions and boiler efficiency while selecting the right oxygen injection and flue gas recycle strategies, and (3) perform technical and economic feasibility studies for application of the technology in demonstration and commercial scale boilers. This document summarizes the work performed during the period of performance of the project (Oct 2002 to June 2007). Detailed technical results are reported in corresponding topical reports that are attached as an appendix to this report. Task 1 (Site Preparation) has been completed in 2003. The experimental pilot-scale O{sub 2}/CO{sub 2} combustion tests of Task 2 (experimental test performance) has been completed in Q2 2004. Process simulation and cost assessment of Task 3 (Techno-Economic Study) has been completed in Q1 2005. The topical report on Task 3 has been finalized and submitted to DOE in Q3 2005. The calculations of Task 4 (Retrofit Recommendation and Preliminary Design of a New Generation Boiler) has been completed in 2004. In Task 6 (engineering study on retrofit applications), the engineering study on 25MW{sub e} unit has been completed in Q2, 2008 along with the corresponding cost assessment. In Task 7 (evaluation of new oxy-fuel power plants concepts), based on the design basis document prepared in 2005, the design and cost estimate of the Air Separation Units, the boiler islands and the CO{sub 2} compression and trains have been completed, for both super and ultra-supercritical case study. Final report of Task-7 is published by DOE in Oct 2007.

  4. Formulation of the task on ergonomic designing of NPP operator activity

    International Nuclear Information System (INIS)

    Anokhin, A.N.

    1996-01-01

    One of the main causes of inefficiency of existing nuclear plant operator activity support means is the absence of common integrated system approach to ergonomic designing of operator activity. Some attempt to formalize the problem as a task of macro-ergonomic designing is made. The structure of anthropocentric functional model of human-operator-nuclear plant system operation is described. Operator activity is characterized by some resulting properties (such as reliability, etc.). These properties are influenced by human-operator internal properties and working environment external properties. The detailed classification of all these properties is offered. The main result of this work is the statement of tasks of operator activity macro-ergonomic designing based on the offered formalization

  5. Steam generator tube rupture risk impact on design and operation of French PWR plants

    International Nuclear Information System (INIS)

    Depond, G.; Sureau, H.

    1984-01-01

    The experience of steam generator tube leaks incidents in PWR plants has resulted in an increase of EDF analysis leading to improvements in design and post-accidental operation for new projects and operating plants. The accident consequences are minimized for each of the NSSS three barriers: first barrier: safeguard systems design and operating procedures relying upon core safety allow to maintain a low level of primary radioactivity, second barrier: steam generator design and periodic inspection allow to reduce tube ruptures risks and third barrier: atmospheric releases are reduced as a result of optimal recovery procedures, detection improvements and atmospheric steam valves design improvements. (orig.)

  6. The design of a 4’th order Bandpass Butterworth filter with one operational amplifier.

    OpenAIRE

    Gaunholt, Hans

    2008-01-01

    A numerical design method is presented for the design of all pole band pass active-RC filters applying just one operational amplifier. The operational amplifier model used is the integrator model: ωt/s where ωt is the unity gain fre-quency. The design method is used for the design of a fourth order band pass filter with Butterworth poles applying just one operational amplifier coupled as a unity gain amplifier. The unity gain amplifiers have the advantage of providing low power consumption, y...

  7. Wet steam turbines for nuclear generating stations -design and operating experience

    International Nuclear Information System (INIS)

    Usher, J.

    1977-01-01

    Lecture to the Institution of Nuclear Engineers, 11 Jan. 1977. The object of this lecture was to give an account of some design features of large wet steam turbines and to show by describing some recent operational experience how their design concepts were fulfilled. Headings are as follows: effects of wet steam cycle on turbine layout and operation (H.P. turbine, L.P. turbine); turbine control and operation; water separators; and steam reheaters. (U.K.)

  8. Conceptual Design of Operation Strategies for Hybrid Electric Aircraft

    Directory of Open Access Journals (Sweden)

    Julian Hoelzen

    2018-01-01

    Full Text Available Ambitious targets to reduce emissions caused by aviation in the light of an expected ongoing rise of the air transport demand in the future drive the research of propulsion systems with lower CO2 emissions. Regional hybrid electric aircraft (HEA powered by conventional gas turbines and battery powered electric motors are investigated to test hybrid propulsion operation strategies. Especially the role of the battery within environmentally friendly concepts with significantly reduced carbon footprint is analyzed. Thus, a new simulation approach for HEA is introduced. The main findings underline the importance of choosing the right power-to-energy-ratio of a battery according to the flight mission. The gravimetric energy and power density of the electric storages determine the technologically feasibility of hybrid concepts. Cost competitive HEA configurations are found, but do not promise the targeted CO2 emission savings, when the well-to-wheel system is regarded with its actual costs. Sensitivity studies are used to determine external levers that favor the profitability of HEA.

  9. Studies on optimal design and operation of integrated distillation arrangements

    Energy Technology Data Exchange (ETDEWEB)

    Christiansen, Atle Christer

    1997-12-31

    During the last decades, there has been growing concern in the chemical engineering environment over the task of developing more cost- and energy efficient process equipment. This thesis discusses measures for improving the end-use energy efficiency of separation systems. It emphasises a certain class of integrated distillation arrangements, in particular it considers means for direct coupling of distillation columns so as to use the underlying physics to facilitate more energy efficient separations. The numerical methods discussed are well suited to solve models of distillation columns. A tear and grid method is proposed that to some extent exploits the sparsity, since the number of tear variables required for solving a distillation model usually is rather small. The parameter continuation method described is well suited for ill-conditioned problems. The analysis of integrated columns is extended beyond the scope of numerical simulations by means of analytical results that applies in certain limiting cases. The consept of preferred separation, which is important for prefractionator arrangements, is considered. From this analysis is derived information that is important for the practical operation of such columns. Finally, the proposed numerical methods are used to optimize Petlyuk arrangements for separating ternary and quaternary mixtures. 166 refs., 130 figs., 20 tabs.

  10. Design, construction and operation of Ontario Hydro's CANDU plants

    International Nuclear Information System (INIS)

    Campbell, P.G.

    1981-06-01

    Ontario Hydro has been producing electricity commercially from nuclear power since 1968, using CANDU reactors which have proved enormously successful. The 206-MW Douglas Point station, nearly 10 times larger than the first Canadian power reactor, NPD-2, resulted from a cooperative effort between Atomic Energy of Canada Ltd., the provincial government of Ontario, and Ontario Hydro. This approach led to a basic working relationship between the parties, with Ontario Hydro acting as project manager and builder, and AECL acting as consultant with respect to the nuclear components. Before Douglas Point was fully commissioned Ontario Hydro was ready to commit itself to more nuclear stations, and work was started on the four-unit Pickering nuclear generating station. Multi-unit stations were adopted to achieve economies of scale, and the concept has been retained for all subsequent nuclear power plants constructed in the province. The organization of Ontario Hydro's project management, construction, and operation of nuclear generating stations is described. Performance of the existing stations and cost of the power they produce have been entirely acceptable

  11. Comprehensive Care

    Science.gov (United States)

    ... Comprehensive Care Share this page Facebook Twitter Email Comprehensive Care Understand the importance of comprehensive MS care ... In this article A complex disease requires a comprehensive approach Today multiple sclerosis (MS) is not a ...

  12. Control of occupational radiation exposures in TVA nuclear power plants - design and operating philosophy

    International Nuclear Information System (INIS)

    Belvin, E.A.; Lyon, M.; Beasley, E.G. Jr.; Zobel, W.; Stone, G.F.

    1976-01-01

    TVA has some 21,000 MWe of nuclear generation in various phases of design, construction, or operation. When Browns Ferry was designed in the late 1960's, there were no guidelines available regarding implant radiation control features, so TVA relied on good engineering and health physics judgement in developing its design and operating criteria for radiation protection. After two years of operation at Browns Ferry, the authors experience shows that their design criteria were in most cases adequate or more than adequate. However, several areas present continuing problems relative to radiation and contamination control. In view of the recent NRC ALARA guidelines, they have instituted a program to ensure that the ALARA concept is made an integral part of their design and operating plans. Administrative documents were issued giving management support to the ALARA concept. A 4-member management audit team consisting of representatives from their design, operating, and radiation protection groups was established to review the effectiveness of radiation protection design features and operating activities on a plant-by-plant basis. Reports and recommendations from these audits are sent to top-level management staff. Their goal is to maintain an audit-appraisal system consisting of in-plant awareness of radiation and contamination conditions, assessment of trends in occupational radiation exposures, and feedback to their designers regarding problems encountered during operation and maintenance activities

  13. The HRMT27 (Rodtarg) Experiment: Design, Operation and First Results

    CERN Document Server

    Torregrosa Martin, Claudio Leopoldo; Calviani, Marco; Butcher, Mark; Horvath, David; Fornasiere, Elvis; Gentini, Luca

    2016-01-01

    The HRMT27-Rodtarg- experiment used the HiRadMat facility at CERN to impact intense 440 GeV proton beams onto thin rods - 8 mm diameter, 140 length - made of high-density materials such as Ir, W, Ta, Mo among others. The purpose of the experiment was to reduce uncertainties on the CERN antiproton target material response and assess the material selection for its future redesign. The experiment was designed to recreate the extreme conditions reached in the target, estimated as an increase of temperature above 2000 ºC in less than 0.5 µs and a subsequent compressive-to-tensile pressure wave of several GPa. This document includes a detailed summary of the experimental setup and online recorded data. Results suggest that all the irradiated materials except tantalum suffered internal damage from conditions 5-7 lower than those reached in the AD-Target, while tantalum targets clearly showed the best dynamic response, remaining un-cracked during the experiment. Foreseen post irradiation examinations will complete ...

  14. Primary design and operation analysis of ITER air transfer system

    International Nuclear Information System (INIS)

    Wang Haitian; Li Ge; Qin Shijun

    2010-01-01

    Air transfer system (ATS) is a remote handling transfer, which can work in the nuclear radiation environment and can be driven by the electricity fully. Its motion power is provided by several servo motors. The remote control technology of ATS, which is China taking part in the plan of international Tokamak experimental reactor (ITER) and grasping this technology, is one of key technologies of ITER. The remote handling technology can lay the foundation for developing demonstration nuclear fusion power plant in China on self-reliance. Because there is gamma irradiation and hazard material in these ITER parts, all required maintenance of port plugs and inner components are been transmitted by ATS. The pick-up or drop-off these components are completed by means of a remotely controlled TCS system between the Vacuum Vessel and the Hot Cell through the bridge-gallery. Tokamak building includes three floors, including upper port, equatorial port and lower port, linked by a lift. According to each port level configuration and safety requirement, the radius of curvature with ATS trajectory is optimized, and a trajectory of each level is determined by positioned guidance beacons. At last, the results of computer aided design (CAD) show single trajectory guidance of ATS in each level is available. (authors)

  15. Design, Operation, and Controlled-Island Operation of the U.S. Department of Energy Solar Decathlon 2013 Microgrid

    Energy Technology Data Exchange (ETDEWEB)

    Kurnik, C. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Butt, R. S. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Metzger, I. [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Lavrova, O. [Univ. of New Mexico, Albuquerque, NM (United States); Patibandla, S. [Univ. of New Mexico, Albuquerque, NM (United States); Wagner, V. [Schneider Electric, Knoxville, TN (United States); Frankosky, M. [Schneider Electric, Knoxville, TN (United States); Wiegand, G. [MicroPlanet, Inc., Woodinville, WA (United States)

    2015-04-22

    This document reports on the design and operation of a high-capacity and high-penetration-ratio microgrid, which consists of 19 photovoltaic-powered residential houses designed by collegiate teams as part of their participation in the U.S. Department of Energy Solar Decathlon 2013. The microgrid was interconnected with the local utility, and resulting net-power and power-quality events were recorded in high detail (1-minute data sampling or better). Also, a controlled-island operation test was conducted to evaluate the microgrid response to additional events such as increased loads (e.g., from electric vehicles) and bypassing of voltage regulators. This temporary ground-laid microgrid was stable under nominal and island-operation conditions; adverse weather and loads did not lead to power-quality degradation.

  16. Design and performance of a clean and economic power supply targeting energy independence and operative security

    Energy Technology Data Exchange (ETDEWEB)

    Mushtaha, Mohammed

    2012-07-01

    Stand alone wind-diesel power systems address the major issues for the supply of remotely located consumers or the provision of enhanced energy independence. The specific configuration considered here comprises a prior wind turbine driven induction generator and a supplementary synchronous generator driven by a combustion engine, the latter caring for frequency control and reactive power balance. An accumulator-bank and a hydrogen storage path consisting of an electrolyzer and a hydrogen storage tank are added as short-term and long-term storage devices - respectively - in order to adjust volatile wind generation and varying load demand. The hydrogen re-conversion to electricity is achieved by design of the drive of the synchronous generator as a dual-fuel engine, fed with stored hydrogen primarily, and with diesel oil in case of the rare event of hydrogen storage emptiness. An elementary waste heat recovery from engine cooling water and from exhaust gases makes the system even more energy efficient and environment friendly. For proper sizing of the particular system components under minimization of the life cycle cost - which are composed of the initial installation cost, the replacement cost, the operation and maintenance cost as well as the remaining fuel cost - the meta-heuristic computational method of Particle Swarm Optimization (PSO) was applied. The crucial task of intelligently managing the energy storage strategy depending on their actual states of charge and the current excess power under a given load profile was solved by a fuzzy system and a subsequent time scheduler, the latter providing definite set-point steps for definite periods of time to the electrolyzer in order to achieve smooth and conservative operation. The concrete design and performance of the proposed system structure is shown with the two relevant application examples of independent electricity supply of the main hospital in Gaza-Strip, Palestine, and a remotely located dairy farm. For

  17. Plant designer's view of the operator's role in nuclear plant safety

    International Nuclear Information System (INIS)

    Corcoran, W.R.; Church, J.F.; Cross, M.T.; Porter, N.J.

    1981-01-01

    The nuclear plant operator's role supports the design assumptions and equipment with four functional tasks. He must set up th plant for predictable response to disturbances, operate the plant so as to minimize the likelihood and severity of event initiators, assist in accomplishing the safety functions, and feed back operating experiences to reinforce or redefine the safety analyses' assumptions. The latter role enhances the operator effectiveness in the former three roles. The Safety Level Concept offers a different perspective that enables the operator to view his roles in nuclear plant safety. This paper outlines the operator's role in nuclear safety and classifies his tasks using the Safety Level Concept

  18. Design of an operator support system for online maintenance at nuclear power plant

    International Nuclear Information System (INIS)

    Chu Yongyue; Li Huwei; Gao Qiang; Yi Yan; Yang Ming

    2013-01-01

    Online maintenance based on reliability centered management is pivotal for the safe and economical operation of Nuclear Power Plant (NPP). This paper presents an operator support system through which the operators can effectively manage plant configuration and identify the weaknesses in plant operation. The proposed operator support system is based on the GO-FLOW, which is a success-oriented availability analysis methodology and can be used for evaluating phased missions. In this paper, the design of the proposed operator support system is introduced through a case study of the Auxiliary Feed Water System (AFWS). (author)

  19. The ability of environmental healthcare design strategies To impact event related anxiety in paediatric patients: A comprehensive systematic review.

    Science.gov (United States)

    Norton-Westwood, Deborah; Pearson, Alan; Robertson-Malt, Suzanne

    Background Children's' hospitals are by definition hospitals specialized in all aspects of children's care, but are they and if so, how is that achieved? Are healthcare facilities more than a 'space' in which to ask medical questions, seek answers and obtain treatment? Some suggest that the very design of a space can positively or negatively impact healing, hence the term referred to by those in the architectural community as 'healing spaces'. To date empirical studies to provide evidence to this effect, although growing in number, are still few. What is known is that hospitals, doctor's offices and dental offices alike unintentionally create an atmosphere, particularly for children, that add to an already heightened level of anxiety and fear. Designing a children's hospital, unlike a generalist facility, presents a unique and significant challenge. Those involved in designing such hospitals are faced with the opportunity and responsibility to care for and respond to the needs of children across the age spectrum; infants to toddlers, school aged children to adolescents. As healthcare professionals and architects, it is our responsibility to create healthcare facilities that are of purposeful design; anticipating and alleviating children's anxiety and fear wherever possible.Objectives The objective of this systematic review is to evaluate the effects of environmental design strategies in healthcare institutions such as hospitals and dental offices on event-related anxiety in the paediatric population.Inclusion Criteria This comprehensive systematic review involved children from the age of 1 to 18 years of age admitted to a healthcare facility with the primary outcomes of interest being four key design strategies: positive distraction; elimination of environmental stressors; access to social support and choice (control); and connection to nature.Search Strategy Using the Joanna Briggs defined three step search strategy, both published and unpublished studies were

  20. Human factors in the design and operation of reactor-safety systems

    International Nuclear Information System (INIS)

    Brookes, M.J.

    1982-01-01

    This chapter examines the degree to which poor design of instruments may have contributed to the TMI accident. Among the issues to be considered are: details of the instrumentation; the relation between poor systems design and errors of judgement; and ways to design the control-room operator-machine interface so that human errors are avoided or minimized

  1. Design, construction, operation, shutdown and surveillance of repositories for solid radioactive wastes in shallow ground

    International Nuclear Information System (INIS)

    1984-01-01

    This report is a part of the IAEA publications under its Programme on Underground Disposal of Radioactive Wastes and is addressed to administrative and technical authorities and specialists who consider the shallow-ground disposal of low- and intermediate-level solid radioactive wastes of short half-lives. The report emphasizes the technological aspects, however it briefly discusses the safety philosophy and regulatory considerations too. The design, construction, operation, shutdown and surveillance of the repositories in shallow ground are considered in some detail, paying special attention to their interrelated aspects. In particular, a review is given of the following aspects: main design and construction considerations in relation to the natural features of the site; design and construction aspects during the repository development process; activities related to operational and post-operational stages of the repository; major steps in repository operation and essential activities in shutdown and operational and post-operational surveillance

  2. Design of an integrated operator support system for advanced NPP MCRs. Issues and perspectives

    International Nuclear Information System (INIS)

    Lee, Seung Jun; Seong Poong-Hyun

    2010-01-01

    Recently, human error has been highlighted as one of the main causes of accidents in nuclear power plants (NPPs). In order to prevent human errors during the main control room (MCR) operations, which are highly complex and mentally taxing activities, improved interfaces and operator support systems have been developed for advanced MCRs. Although operator support systems have the capability to improve the safety and reliability of an NPP, inappropriate designs can have adverse effects on the system safety. Designs based on systematic development frames and validation/verification of the systems are pivotal strategies to circumvent the negative effects of operator support systems. In this paper, an integrated operator support system designed to aid the cognitive activities of operators as well as theoretical and experimental evaluation methods of operator support systems are reviewed. From this review, it was concluded that not only issues about systems (e.g., the accuracy of the system outputs), but also issues about human operators who use the systems (for instance, information quality, the operator's trust and dependency on support systems) should be considered in the design of efficient operator support systems. (author)

  3. Design of a compressed air modulator to be used in comprehensive multidimensional gas chromatography and its application in the determination of pesticide residues in grapes

    NARCIS (Netherlands)

    Pizzutti, I.R.; Vreuls, J.J.; Kok, A; Roehrs, R.; Martel, S.; Friggi, C.A.; Zanella, R.

    2009-01-01

    In this study, a new modulator that is simple, robust and presents low operation costs, was developed. This modulator uses compressed air to cool two small portions in the first centimeters of the second chromatographic column of a comprehensive multidimensional gas chromatography (GC × GC) system.

  4. Improved Design of Crew Operation in Computerized Procedure System of APR1400

    Energy Technology Data Exchange (ETDEWEB)

    Seong, No Kyu; Jung, Yeon Sub; Sung, Chan Ho [KHNP, Daejeon (Korea, Republic of)

    2016-05-15

    The operators perform the paper-based procedures in analog-based conventional main control room (MCR) depending on only communications between operators except a procedure controller such as a Shift Supervisor (SS), however in digital-based MCR the operators can confirm the procedures simultaneously in own console when the procedure controller of computerized procedure (CP) opens the CP. The synchronization and a synchronization function between procedure controller and other operators has to be considered to support the function of crew operation. This paper suggests the improved design of crew operation in computerized procedure system of APR1400. This paper suggests the improved design of APR1400 CPS. These improvements can help operators perform the crew procedures more efficiently. And they reduce a burden of communication and misunderstanding of computerized procedures. These improvements can be applied to CPS after human factors engineering verification and validation.

  5. Pre-Swirl Stator and Propeller Design for Varying Operating Conditions

    DEFF Research Database (Denmark)

    Saettone, Simone; Regener, Pelle Bo; Andersen, Poul

    2016-01-01

    blades ahead of the propeller.This paper describes the hydrodynamic design of apre-swirl stator with radially variable pitch, paired with aconventional propeller. The aim is to achieve the highest possible effciency in various operating conditions, and to avoid effciency penalties in off-design operation.......To investigate the propeller and stator designs and configurations in different operating conditions, the computationally inexpensive vortex-lattice method is used a sa first step to optimize the geometry in an initial parameter study. Then the flow over hull, stator and propelleris simulated in a CFD...

  6. A Function-Behavior-State Approach to Designing Human Machine Interface for Nuclear Power Plant Operators

    Science.gov (United States)

    Lin, Y.; Zhang, W. J.

    2005-02-01

    This paper presents an approach to human-machine interface design for control room operators of nuclear power plants. The first step in designing an interface for a particular application is to determine information content that needs to be displayed. The design methodology for this step is called the interface design framework (called framework ). Several frameworks have been proposed for applications at varying levels, including process plants. However, none is based on the design and manufacture of a plant system for which the interface is designed. This paper presents an interface design framework which originates from design theory and methodology for general technical systems. Specifically, the framework is based on a set of core concepts of a function-behavior-state model originally proposed by the artificial intelligence research community and widely applied in the design research community. Benefits of this new framework include the provision of a model-based fault diagnosis facility, and the seamless integration of the design (manufacture, maintenance) of plants and the design of human-machine interfaces. The missing linkage between design and operation of a plant was one of the causes of the Three Mile Island nuclear reactor incident. A simulated plant system is presented to explain how to apply this framework in designing an interface. The resulting human-machine interface is discussed; specifically, several fault diagnosis examples are elaborated to demonstrate how this interface could support operators' fault diagnosis in an unanticipated situation.

  7. Optimum Design of a Coil Spring for Improving the Performance of a Spring -Operated Mechanism

    International Nuclear Information System (INIS)

    Lee, Dae Woo; Sohn, Jeong Hyun; Yoo, Wan Suk

    2016-01-01

    In this study, a release test bed is designed to evaluate the dynamic behaviors of a coil spring. From the release tests, the dynamic behaviors of a coil spring are analyzed. A lumped parameter spring model was established for numerical simulation of a spring. The design variables of a coil spring are optimized by using the design of experiments approach. Two-level factorial designs are used for the design optimization, and the primary effects of the design variables are analyzed. Based on the results of the interaction analysis and design sensitivity analysis, the level of the design variables is rearranged. Finally, the mixed-level factorial design is used for the optimum design process. According to the optimum design of the opening spring, the dynamic performance of the spring-operated mechanism increases by 2.90

  8. Integrating operation design into infrastructure planning to foster robustness of planned water systems

    Science.gov (United States)

    Bertoni, Federica; Giuliani, Matteo; Castelletti, Andrea

    2017-04-01

    Over the past years, many studies have looked at the planning and management of water infrastructure systems as two separate problems, where the dynamic component (i.e., operations) is considered only after the static problem (i.e., planning) has been resolved. Most recent works have started to investigate planning and management as two strictly interconnected faces of the same problem, where the former is solved jointly with the latter in an integrated framework. This brings advantages to multi-purpose water reservoir systems, where several optimal operating strategies exist and similar system designs might perform differently on the long term depending on the considered short-term operating tradeoff. An operationally robust design will be therefore one performing well across multiple feasible tradeoff operating policies. This work aims at studying the interaction between short-term operating strategies and their impacts on long-term structural decisions, when long-lived infrastructures with complex ecological impacts and multi-sectoral demands to satisfy (i.e., reservoirs) are considered. A parametric reinforcement learning approach is adopted for nesting optimization and control yielding to both optimal reservoir design and optimal operational policies for water reservoir systems. The method is demonstrated on a synthetic reservoir that must be designed and operated for ensuring reliable water supply to downstream users. At first, the optimal design capacity derived is compared with the 'no-fail storage' computed through Rippl, a capacity design function that returns the minimum storage needed to satisfy specified water demands without allowing supply shortfall. Then, the optimal reservoir volume is used to simulate the simplified case study under other operating objectives than water supply, in order to assess whether and how the system performance changes. The more robust the infrastructural design, the smaller the difference between the performances of

  9. Improving emergency management through shared information processing - considerations in Emergency Operations Center design

    International Nuclear Information System (INIS)

    DeBusk, R.E.; Walker, J.A.

    1987-01-01

    An Emergency Operations Center (EOC) is a shared information processing facility. Although seemingly obvious, many EOCs are designed and operated based on other criteria. The results, measured in terms of response effectiveness, are difficult to determine. A review of some recent disasters reveals a pattern of poor performance for the EOCs involved. These conclusions are tentative because so little research has been done on the design, operation, or evaluation of emergency operations centers. The EOC is not an onsite response command post but a facility removed from the response where tactical and strategic decisions are made based on information from the response site and elsewhere. The EOC is therefore the central focus of emergency information processing and higher-level decision making. Examining existing EOCs, several common functions emerge. These functions can be described in terms of shared information processing. However, many factors impact the design and operation of EOCs. Politics, budgets, and personal ambition are only a few such factors. Examining EOC design and operation in terms of shared information processing operationalized in the seven principal functions within the EOC provides a framework for establishing principles of EOC design and operation. In the response to emergencies such as Bhopal or Chernobyl the stakes are high. Applying new techniques and technologies of management systems can improve the probability of success. This research is a beginning step - to understand how EOCs function, to define the system. Predictive or prescriptive analysis must wait until sufficient empirical data is available to complete a descriptive model for EOC operations

  10. A Virtual Reality Framework to Optimize Design, Operation and Refueling of GEN-IV Reactors

    International Nuclear Information System (INIS)

    Rizwan-uddin; Nick Karancevic; Stefano Markidis; Joel Dixon; Cheng Luo; Jared Reynolds

    2008-01-01

    Many GEN-IV candidate designs are currently under investigation. Technical issues related to material, safety and economics are being addressed at research laboratories, industry and in academia. After safety, economic feasibility is likely to be the most important criterion in the success of GEN-IV design(s). Lessons learned from the designers and operators of GEN-II (and GEN-III) reactors must play a vital role in achieving both safety and economic feasibility goals

  11. A Virtual Reality Framework to Optimize Design, Operation and Refueling of GEN-IV Reactors.

    Energy Technology Data Exchange (ETDEWEB)

    Rizwan-uddin; Nick Karancevic; Stefano Markidis; Joel Dixon; Cheng Luo; Jared Reynolds

    2008-04-23

    many GEN-IV candidate designs are currently under investigation. Technical issues related to material, safety and economics are being addressed at research laboratories, industry and in academia. After safety, economic feasibility is likely to be the most important crterion in the success of GEN-IV design(s). Lessons learned from the designers and operators of GEN-II (and GEN-III) reactors must play a vital role in achieving both safety and economic feasibility goals.

  12. Impact of Concreteness on Comprehensibility, Interest, and Memory for Text: Implications for Dual Coding Theory and Text Design.

    Science.gov (United States)

    Sadoski, Mark; And Others

    1993-01-01

    The comprehensibility, interestingness, familiarity, and memorability of concrete and abstract instructional texts were studied in 4 experiments involving 221 college students. Results indicate that concreteness (ease of imagery) is the variable overwhelmingly most related to comprehensibility and recall. Dual coding theory and schema theory are…

  13. Scenario-based design: a method for connecting information system design with public health operations and emergency management.

    Science.gov (United States)

    Reeder, Blaine; Turner, Anne M

    2011-12-01

    Responding to public health emergencies requires rapid and accurate assessment of workforce availability under adverse and changing circumstances. However, public health information systems to support resource management during both routine and emergency operations are currently lacking. We applied scenario-based design as an approach to engage public health practitioners in the creation and validation of an information design to support routine and emergency public health activities. Using semi-structured interviews we identified the information needs and activities of senior public health managers of a large municipal health department during routine and emergency operations. Interview analysis identified 25 information needs for public health operations management. The identified information needs were used in conjunction with scenario-based design to create 25 scenarios of use and a public health manager persona. Scenarios of use and persona were validated and modified based on follow-up surveys with study participants. Scenarios were used to test and gain feedback on a pilot information system. The method of scenario-based design was applied to represent the resource management needs of senior-level public health managers under routine and disaster settings. Scenario-based design can be a useful tool for engaging public health practitioners in the design process and to validate an information system design. Copyright © 2011 Elsevier Inc. All rights reserved.

  14. The interactions of design, control and operability in reactive distillation systems

    DEFF Research Database (Denmark)

    Georgiadis, M.C.; Schenk, Myrian Andrea; Pistikopoulos, Stratos

    2002-01-01

    is a strong function of the process design and potential operability bottlenecks are identified. In the second approach, the process design and the control system are optimized simultaneously leading to a more economically beneficial and better controlled system than that obtained using the sequential......In this work the design and control of a reactive distillation column, described by a rigorous dynamic model, is tackled via two different optimization approaches. In the first, the steady-state process design and the control system are optimized sequentially. It is shown that operability...

  15. Design tools for computer-generated display of information to operators

    International Nuclear Information System (INIS)

    O'Brien, J.F.; Cain, D.G.; Sun, B.K.H.

    1985-01-01

    More and more computers are being used to process and display information to operators who control nuclear power plants. Implementation of computer-generated displays in power plant control rooms represents a considerable design challenge for industry designers. Over the last several years, the EPRI has conducted research aimed at providing industry designers tools to meet this new design challenge. These tools provide guidance in defining more 'intelligent' information for plant control and in developing effective displays to communicate this information to the operators. (orig./HP)

  16. On site PWR fuel inspection measurements for operational and design verification

    International Nuclear Information System (INIS)

    1996-01-01

    The on-site inspection of irradiated Pressurized Water Reactor (PWR) fuel and Non-Fuel Bearing Components (NFBC) is typically limited to visual inspections during refuelings using underwater TV cameras and is intended primarily to confirm whether the components will continue in operation. These inspections do not normally provide data for design verification nor information to benefit future fuel designs. Japanese PWR utilities and Nuclear Fuel Industries Ltd. designed, built, and performed demonstration tests of on-site inspection equipment that confirms operational readiness of PWR fuel and NFBC and also gathers data for design verification of these components. 4 figs, 3 tabs

  17. The Design and Implementation of Test System Based on Programmable Excitation Power Supply for Mining Comprehensive Protector

    Directory of Open Access Journals (Sweden)

    Zhi-jie Zhang

    2013-11-01

    Full Text Available As comprehensive protectors for coal mining (referred to comprehensive protectors in use are prone to fail, it can timely screen out the invalid comprehensive protector by periodic functional test when it is used (it is called test in use to ensure the production safety. The test in use needs the specialized test equipment, which is not used in delivery inspection by the manufacturers of comprehensive protectors. Thus, testing excitation power becomes a constraint for the improvement of the accuracy of test in use and the degree of automation. To solve the problem, this paper developed a power frequency programmed input-output testing excitation power supply, and on that basis it also realized the mining comprehensive protector test system in use with the excitation circuit and voltage program-controlled output.

  18. Recent advances and achievements in WWER-1000 fuel design performance and operation

    International Nuclear Information System (INIS)

    Vasilchenko, I.; Molchanov, V.

    2009-01-01

    In this paper the main results of TVS-2 (TVS-2M) basic design operation like TVS-2 - 1216 pcs., including 687 in operation, TVS-2M - 66 pcs. in operation (Balakovo-1); reliability -1,6·10-6 in 2008 and the Balakovo NPP capacity factor - 90% are presented. Average efficient operating time of the Balakovo power units, calculated capacity factor for the Balakovo NPP at transition to fuel cycle 3x1,5, contemporary operational requirements for fuel and their realization as well as SPND axial position variation in the core with TVS - 2M and CPS AR usage are shown

  19. Design and Implementation of Multi Agentbased Information Fusion System for Decision Making Support (A Case Study on Military Operation

    Directory of Open Access Journals (Sweden)

    Arwin Datunaya Wahyudi Sumari

    2013-09-01

    Full Text Available Quick, accurate, and complete information is highly required for supporting strategically impact decision making in a Military Operation (MO in order to reduce the decision cycle and to minimize the loss. For that purpose, we propose, design and implement a hierarchical Multi Agentbased Information Fusion System for Decision Making Support (MAIFSDMS. The information fusion is implemented by applying Maximum Score of the Total Sum of Joint Probabilities (MSJP fusion method and is done by a collection of Information Fusion Agents (IFA that forms a multiagent system. MAIFS uses a combination of generalization of Dasarathy and Joint Director’s Laboratory (JDL process models for information fusion mechanism. Information fusion products that are displayed in graphical forms provide comprehensive information regarding the MO’s area dynamics. By observing the graphics resulted from the information fusion, the commandant will have situational awareness and knowledge in order to make the most accurate strategic de cision as fast as possible.

  20. Customer Attraction in a Design-Build-Finance-Maintain-Operate Contract

    NARCIS (Netherlands)

    Favie, R.; Nordennen, van A.; Kleine, A.J.; Maas, G.J.; Ceric, A.; Radujkovic, M.

    2009-01-01

    In the Netherlands, large public customers use integrated contracts more and more often for complicated civil engineering and architectural works. Projects with integrated contracts such as Design, Build, Finance, Maintenance and Operate require tenderers to behave differently than they are

  1. Guidelines for the design and operation of makeup water treatment systems

    International Nuclear Information System (INIS)

    Lee, Y.H.; Planek, M.A.; Sopocy, D.M.; Tomaga, C.M.; Abrams, I.M.; Anderson, C.C.; Balazs, M.K.; Houskava, J.; Williams, R.

    1989-06-01

    These guidelines present the industry with a standardized program to ensure the optimum design and operation of their individual makeup water treatment systems. These guidelines present, in a non-technical and non-proprietary format, the makeup water treatment system design and operating topics that are discussed in detail in Volumes 1 and 2 of NP-6377-SL. The individual guidelines contained in Volumes 1 and 2 are presented as separate imperative statements, followed by a technical justification discussion, which provides further explanations. In addition and when applicable, the guidelines relate pertinent operational in regard to monitoring parameters for operation, alternative actions, troubleshooting, management responsibilities and shutdown practices. Design considerations are also addressed, when applicable, in regard to equipment cost and advantages and disadvantages for the design recommendations. Appendices provide background information for performance criteria, component description, economic evaluation procedures and definitions. 4 refs

  2. Compilation of Energy Efficient Concepts in Advanced Aircraft Design and Operations. Volume 1. Technical report

    National Research Council Canada - National Science Library

    Clyman, Milton

    1980-01-01

    .... The search addressed the technologies necessary to support next generation (IOC 1990+) air vehicle design and operation concepts that will reduce the requirement for natural petroleum-derived energy...

  3. Designing a Professional Development Plan for the Support Operations Officer of the Forward Support Company

    National Research Council Canada - National Science Library

    Zimmerman, Edward

    1999-01-01

    .... Based on these responsibilities, the research question (Does the Army need to design a specific professional development plan to train CSS lieutenants to serve as support operations officers in the FSC...

  4. Enhancing human performance in ship operations by modifying global design factors at the design stage

    International Nuclear Information System (INIS)

    Montewka, Jakub; Goerlandt, Floris; Innes-Jones, Gemma; Owen, Douglas; Hifi, Yasmine; Puisa, Romanas

    2017-01-01

    Usually the improvements of human performance in the course of ship design process is carried out by modifying local ergonomics, like electronic visualisation and information display systems on the bridge or in the engine control room, stair or hatch covers design. However, the effect of global design factors (GDFs), such as ship motion, whole body vibration and noise, on human performance has not been given attention before. Such knowledge would allow the improvements of human performance by effective design modification on very early stage of ship design process. Therefore, in this paper we introduce probabilistic models linking the effect of GDFs with the human performance suitable for ship design process. As a theoretical basis for modelling human performance the concept of Attention Management is utilized, which combines the theories described by Dynamic Adaptability Model, Cognitive Control Model and Malleable Attentional Resources Theory. Since the analysed field is characterised by a high degree of uncertainty, we adopt a specific modelling technique along with a validation framework that allows uncertainty treatment and helps the potential end-users to gain confidence in the models and the results that they yield. The proposed models are developed with the use Bayesian Belief Networks, which allows systematic translation of the available background knowledge into a coherent network and the uncertainty assessment and treatment. The obtained results are promising as the models are responsive to changes in the GDF nodes as expected. The models may be used as intended by naval architects and vessel designers, to facilitate risk-based ship design. - Highlights: • Models linking the effect of GDFs with the human performance are established. • Three global design factors (GDFs) are considered: ship motion, body vibration, noise. • Attention Management concept as theoretical base is modelled with Bayesian Networks. • Two models are developed that can be

  5. REVA Advanced Fuel Design and Codes and Methods - Increasing Reliability, Operating Margin and Efficiency in Operation

    Energy Technology Data Exchange (ETDEWEB)

    Frichet, A.; Mollard, P.; Gentet, G.; Lippert, H. J.; Curva-Tivig, F.; Cole, S.; Garner, N.

    2014-07-01

    Since three decades, AREVA has been incrementally implementing upgrades in the BWR and PWR Fuel design and codes and methods leading to an ever greater fuel efficiency and easier licensing. For PWRs, AREVA is implementing upgraded versions of its HTP{sup T}M and AFA 3G technologies called HTP{sup T}M-I and AFA3G-I. These fuel assemblies feature improved robustness and dimensional stability through the ultimate optimization of their hold down system, the use of Q12, the AREVA advanced quaternary alloy for guide tube, the increase in their wall thickness and the stiffening of the spacer to guide tube connection. But an even bigger step forward has been achieved a s AREVA has successfully developed and introduces to the market the GAIA product which maintains the resistance to grid to rod fretting (GTRF) of the HTP{sup T}M product while providing addition al thermal-hydraulic margin and high resistance to Fuel Assembly bow. (Author)

  6. Fibroid interventions: reducing symptoms today and tomorrow: extending generalizability by using a comprehensive cohort design with a randomized controlled trial.

    Science.gov (United States)

    AbdElmagied, Ahmed M; Vaughan, Lisa E; Weaver, Amy L; Laughlin-Tommaso, Shannon K; Hesley, Gina K; Woodrum, David A; Jacoby, Vanessa L; Kohi, Maureen P; Price, Thomas M; Nieves, Angel; Miller, Michael J; Borah, Bijan J; Gorny, Krzysztof R; Leppert, Phyllis C; Lemens, Maureen A; Stewart, Elizabeth A

    2016-09-01

    Uterine fibroids are an important source of morbidity for reproductive-aged women. Despite an increasing number of alternatives, hysterectomies account for about 75% of all fibroid interventional treatments. Evidence is lacking to help women and their health care providers decide among alternatives to hysterectomy. Fibroid Interventions: Reducing Symptoms Today and Tomorrow (NCT00995878, clinicaltrials.gov) is a randomized controlled trial to compare the safety, efficacy, and economics of 2 minimally invasive alternatives to hysterectomy: uterine artery embolization and magnetic resonance imaging-guided focused ultrasound surgery. Although randomized trials provide the highest level of evidence, they have been difficult to conduct in the United States for interventional fibroid treatments. Thus, contemporaneously recruiting women declining randomization may have value as an alternative strategy for comparative effectiveness research. We sought to compare baseline characteristics of randomized participants with nonrandomized participants meeting the same enrollment criteria and to determine whether combining the 2 cohorts in a comprehensive cohort design would be useful for analysis. Premenopausal women with symptomatic uterine fibroids seeking interventional therapy at 3 US academic medical centers were randomized (1:1) in 2 strata based on calculated uterine volume (<700 and ≥700 cc(3)) to undergo embolization or focused ultrasound surgery. Women who met the same inclusion criteria but declined randomization were offered enrollment in a parallel cohort. Both cohorts were followed up for a maximum of 36 months after treatment. The measures addressed in this report were baseline demographics, symptoms, fibroid and uterine characteristics, and scores on validated quality-of-life measures. Of 723 women screened, 57 were randomized and 49 underwent treatment (27 with focused ultrasound and 22 with embolization). Seven of the 8 women randomized but not treated were

  7. HMI design of MIRROR PLANT for Safe Operation and Application to Vinyl Acetate Monomer Process

    International Nuclear Information System (INIS)

    Hatsugai, Emiko; Nakaya, Makoto

    2014-01-01

    Dynamic plant simulators have always been used off-line for operator training and control loop design prior to the plant construction phase. Here, we propose on-line use of a dynamic simulator for the development of new plant operation. The developed MIRROR PLANT is an on-line dynamic plant simulator that can perfectly simulate dynamic plant behavior, and can also be used to forecast future plant behavior by making the computer run the simulation faster than real-time. Using the estimated and forecast data, the plant operator can detect abnormal situations in the plant. Before activating an alarm from the conventional control system, the operator will be able to perform proactive operation to maintain safety. In this paper, we propose a new human-machine interface (HMI) design to realize proactive operation and discuss application of the HMI to the vinyl acetate monomer process as an example of MIRROR PLANT

  8. Assessment of LWR piping design loading based on plant operating experience

    International Nuclear Information System (INIS)

    Svensson, P.O.

    1980-08-01

    The objective of this study has been to: (1) identify current Light Water Reactor (LWR) piping design load parameters, (2) identify significant actual LWR piping loads from plant operating experience, (3) perform a comparison of these two sets of data and determine the significance of any differences, and (4) make an evaluation of the load representation in current LWR piping design practice, in view of plant operating experience with respect to piping behavior and response to loading

  9. Proceedings of the 2. international conference on containment design and operation. Vol. 1,2

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence, S R

    1991-12-31

    The second international conference on containment design and operation included sessions on the following topics: plenary; commissioning and operation; regulatory and performance requirements; reliability, risk and severe accident evaluation; future containment systems; severe accident evaluation; activity transport experiments; activity transport analysis; containment design; future and filtered vent containment systems; containment response; hydrogen combustion. Due prominence was given to CANDU and other PHWR reactors, and to Canadian experiments. The individual papers have been abstracted separately.

  10. Mechanical testing - designers need: a view at component design and operations stages

    International Nuclear Information System (INIS)

    Shrivastava, S.K.

    2007-01-01

    Mechanical design of any component requires knowledge of values of various material properties which designer(s) make(s) use in designing the component. In design of nuclear power plant components, it assumes even greater importance in view of degree of precision and accuracy with which the values of various properties are required. This is in turn demands, high accuracy in testing machines and measuring methods. In this paper, attempt has been made to bring out that even from conventional tension test, how designer today looks for availability of engineering stress-strain diagram preferably through digitally acquired data points during the test from which he can derive values of Ramberg-Osgood parameters for use in fracture mechanics based analysis. Attempt has been also made to provide account of some of important fracture mechanics related tests which have been evolved in last two decades and designers need for evolution of simple test techniques to measure many more fracture mechanics related parameters as well as cater to constraints such as shape and size of material available from the components. Nuclear power plant has been primarily kept in view and ASME. Section III NB, ASME Section XI and relevant ASTM Standards have been taken as standard references. Further pressure retaining materials of pressure vessels/Reactor Pressure Vessels have been kept in view. (author)

  11. Conceptual design of PF coil system and operation scenario on inductively-operated day-long pulsed tokamak reactor

    International Nuclear Information System (INIS)

    Wang, J.F.; Yamamoto, T.; Ogawa, Y.

    1994-01-01

    It is said that disadvantages of pulsed operation in tokamak fusion reactor are fatigue problem of structural materials and an introduction of energy storage System to compensate the power during the dwell time. To overcome theses disadvantages the authors have designed an inductively-operated ultralong pulsed tokamak called (IDLT) reactor where plasma with a major radius of 10 m are employed so as to provide a magnetic flux necessary to sustain a plasma current inductively during 10 hours or more. This makes it possible to reduce the total cycle number to be around 10 4 during the life of the fusion plant. In pulsed operation reactors the shorter dwell time with a quick start-up and shut down of plasma is very convenient to realize a high availability of the power plant, but it will induce more severe conditions for the hardware design. The authors assumed the dwell time of 5∼10 minutes and analyzed the feasibility of plasma operation scenario for IDLT reactor, especially paying much attention to PF coil system. The stored energy of PF coil system becomes ∼100 GJ, which is comparable with that of toroidal field coil system. When the plasma current of 14 MA is ramped up with a time of 100 seconds, it is found that the maximum capacity of 1 GW is necessary for PF coil power supply. Engineering issues related with AC/hysterisis loss should be carefully examined

  12. How to open & operate a financially successful web site design business

    CERN Document Server

    Evans, Charlotte

    2009-01-01

    The Pricing & Ethical Guidelines Handbook published by the Graphic Arts Guild reports that the average cost of designing a Web site for a small corporation can range from 7,750 to 15,000. It is incredibly easy to see the enormous profit potential. Web design businesses can be run part- or full-time and can easily be started in your own home. As such, they are one of the fastest growing segments of the Internet economy. Here is the manual you need to cash in on this highly profitable segment of the industry. This book is a comprehensive and detailed study of the business side of Web site des

  13. Implementation of utilities operation and maintenance experience into the European pressurized water reactor design

    International Nuclear Information System (INIS)

    Zaiss, W.; Lallier, M.

    1999-01-01

    Since 1992 Electricite de France EDF and German Utilities GU work together with Nuclear Power International NPI, a subsidiary of Framatome and Siemens, in the development of the future European Pressurized Water Reactor EPR. The EPR is an evolutionary concept, based on the French N4 plants and the German KONVOI plants. From the beginning, experienced operation and maintenance people from the precursor plants participate at the design process. Their experience will lead to a plant, which is not only characterised by low investment costs, but also by good operability, high availability and low operation and maintenance costs. No expensive back-fittings should be necessary after commissioning, to reach these availability and maintenance targets. The utility specialists give design requirements for outage performance, system design, and layout. These design requirements are really determining the system performances, and not what was design basis before. It does not necessarily lead to system increases. Mainly it is a shifting of the emphasis to other items. There are even cases, where the system performances can be reduced. Mostly very small modifications, which are nearly cost neutral when implemented early in the design, have big impact on the further operation. If there are big cost influences, a sound balance between investment and gained availability is made together with the designers. There is very fruitful discussion between designers and operators, which is highly estimated by both sides. In this frame also new, revolutionary ideas are coming up, which are going mostly in the direction of investment cost reduction, without loosing operation freedom. It is the first time in Europe, that designers and operators are working so close together. It is also the first time, that the management and the decision making is dominated by the utilities. (author)

  14. 46 CFR 170.270 - Door design, operation, installation, and testing.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Door design, operation, installation, and testing. 170..., operation, installation, and testing. (a) Each Class 1 door must have a quick action closing device... the welding process so that the door frame is not distorted. (e) For each watertight door which is in...

  15. 78 FR 69139 - Physical Security-Design Certification and Operating Reactors

    Science.gov (United States)

    2013-11-18

    ... Operating Reactors AGENCY: Nuclear Regulatory Commission. ACTION: Standard review plan--draft section..., ``Physical Security--Design Certification and Operating Reactors.'' The public comment period was originally....regulations.gov and search for Docket ID NRC-2013-0225. Address questions about NRC dockets to Carol Gallagher...

  16. The design and operation of the THORP central control room: a human factors perspective

    International Nuclear Information System (INIS)

    Reed, Julie.

    1996-01-01

    The new Thermal Oxide Reprocessing Plant (THORP) at British Nuclear Fuels (BNFL) Sellafield Site is now operational. This paper describes the Central Control Room (CCR), focusing on the control system components. Throughout the design, commissioning and operation of THORP, human factors played an important part. (author)

  17. Fast reactor steam generators with sodium on the tube side. Design and operational parameters

    International Nuclear Information System (INIS)

    1994-01-01

    A comparison of design and operational characteristics as well as analysis of experience gained during the long terms operation of the Micro Module Inverse Steam Generator and Module Inverse Steam Generator at BOR 60 reactor are main aims of this technical report. 20 refs, 47 figs, 14 tabs

  18. The design and operation of the slow controls for the DELPHI experiment at LEP

    International Nuclear Information System (INIS)

    Adye, T.J.; Augustinus, A.; Doenszelmann, M.; Rovelli, T.; Sekulin, R.L.; Smith, G.R.

    1994-01-01

    The slow controls of the DELPHI detector enable a single operator to oversee the proper functioning of the apparatus and to diagnose faults as they occur. The hardware and software of this system, as well as their interface to the experiment and the operator, are described. Finally, we attempt to draw some conclusions from seven years' design work and the initial four years' operation of DELPHI. ((orig.))

  19. The design and operation of the slow controls for the DELPHI experiment at LEP

    International Nuclear Information System (INIS)

    Adye, T.J.; Sekulin, R.L.; Smith, G.R.; Augustinus, A.; Rovelli, T.

    1994-03-01

    The slow controls of the DELPHI detector enable a single operator to oversee the proper functioning of the apparatus and to diagnose faults as they occur. The hardware and software of this system, as well as their interface to the experiment and the operator, are described. Finally, we attempt to draw some conclusions from seven years' design work and the initial four years' operation of DELPHI. (author)

  20. The Effects of Phonological Short-Term Memory and Speech Perception on Spoken Sentence Comprehension in Children: Simulating Deficits in an Experimental Design

    Science.gov (United States)

    Higgins, Meaghan C.; Penney, Sarah B.; Robertson, Erin K.

    2017-01-01

    The roles of phonological short-term memory (pSTM) and speech perception in spoken sentence comprehension were examined in an experimental design. Deficits in pSTM and speech perception were simulated through task demands while typically-developing children (N = 71) completed a sentence-picture matching task. Children performed the control,…