Influence of high-energy milling on structure and microstructure of asbestos-cement materials

Science.gov (United States)

Iwaszko, Józef; Zawada, Anna; Lubas, Małgorzata

2018-03-01

Asbestos-Containing Waste (ACW) in the form of a fragment from an asbestos-cement board was subjected to high-energy milling in a planetary mill at a constant rotational speed of 650 rpm and for variable milling times: 1, 2, and 3 h. The initial and the milled materials were subjected to infrared spectroscopic examination to identify the asbestos variety and to evaluate changes in the structure caused by high-energy milling. FT-IR (Fourier Transform Infrared Spectroscopy) examinations followed optical microscopy and SEM (Scanning Electron Microscopy) studies as well as X-ray analysis of the phase composition. It was found that the asbestos fibres present in the asbestos-cement board were respirable fibres with pathogenic properties. Identifying asbestos using the spectroscopic method showed that chrysotile asbestos was present in the as-received ACW while no characteristics of absorption bands from crocidolite or amosite were found. The results of the spectroscopic examinations were confirmed by the X-ray phase analysis. During SEM investigations of the milled ACW, complete loss of the fibrous structure of chrysotile was observed. The FT-IR examinations of the milled material showed that with an increased milling time, the characteristic absorption bands characteristic for chrysotile diminished and already after 2 h of milling their almost complete decay was observed. Thereby, it was confirmed that high-energy milling results in destruction of the crystalline structure of the asbestos phase. The conducted studies have shown that the treatment of asbestos-cement materials using high-energy milling is an effective method for asbestos disposal, capable of competing with other technologies and solutions. Moreover, FT-IR spectroscopy was found to be useful to identify asbestos phases and to assess changes caused by high-energy milling.

Pulsed Corona Plasma Technology for Treating VOC Emissions from Pulp Mills

International Nuclear Information System (INIS)

Fridman, Alexander A.; Gutsol, Alexander; Kennedy, Lawrence A.; Saveliev, Alexei V.; Korobtsev, Sergey V.; Shiryaevsky, Valery L.; Medvedev, Dmitry

2004-01-01

Under the DOE Office of Industrial Technologies Forest Products program various plasma technologies were evaluated under project FWP 49885 ''Experimental Assessment of Low-Temperature Plasma Technologies for Treating Volatile Organic Compound Emissions from Pulp Mills and Wood Products Plants''. The heterogeneous pulsed corona discharge was chosen as the best non-equilibrium plasma technology for control of the vent emissions from HVLC Brownstock Washers. The technology for removal of Volatile Organic Compounds (VOCs) from gas emissions with conditions typical of the exhausts of the paper industry by means of pulsed corona plasma techniques presented in this work. For the compounds of interest in this study (methanol, acetone, dimethyl sulfide and ? -pinene), high removal efficiencies were obtained with power levels competitive with the present technologies for the VOCs removal. Laboratory experiments were made using installation with the average power up to 20 W. Pilot plant prepared for on-site test has average plasma power up to 6.4 kW. The model of the Pilot Plant operation is presented

Understanding dental CAD/CAM for restorations--dental milling machines from a mechanical engineering viewpoint. Part B: labside milling machines.

Science.gov (United States)

Lebon, Nicolas; Tapie, Laurent; Duret, Francois; Attal, Jean-Pierre

2016-01-01

Nowadays, dental numerical controlled (NC) milling machines are available for dental laboratories (labside solution) and dental production centers. This article provides a mechanical engineering approach to NC milling machines to help dental technicians understand the involvement of technology in digital dentistry practice. The technical and economic criteria are described for four labside and two production center dental NC milling machines available on the market. The technical criteria are focused on the capacities of the embedded technologies of milling machines to mill prosthetic materials and various restoration shapes. The economic criteria are focused on investment cost and interoperability with third-party software. The clinical relevance of the technology is discussed through the accuracy and integrity of the restoration. It can be asserted that dental production center milling machines offer a wider range of materials and types of restoration shapes than labside solutions, while labside solutions offer a wider range than chairside solutions. The accuracy and integrity of restorations may be improved as a function of the embedded technologies provided. However, the more complex the technical solutions available, the more skilled the user must be. Investment cost and interoperability with third-party software increase according to the quality of the embedded technologies implemented. Each private dental practice may decide which fabrication option to use depending on the scope of the practice.

Asphalt emulsion radon barrier systems for uranium mill tailings: an overview of the technology

International Nuclear Information System (INIS)

Baker, E.G.; Hartley, J.N.; Freeman, H.D.; Gates, T.E.; Nelson, D.A.; Dunning, R.L.

1984-03-01

Pacific Northwest Laboratory (PNL), under contract to the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project (UMTRAP) office, has developed an asphalt emulsion cover system to reduce the release of radon from uranium mill tailings. The system has been field tested at Grand Junction, Colorado. Results from laboratory and field tests indicate that this system is effective in reducing radon release to near-background levels ( -2 s -1 ) and has the properties required for long-term effectiveness and stability. Engineering specifications have been developed, and analysis indicates that asphalt emulsion covers are cost-competitive with other cover systems. This report summarizes the technology for asphalt emulsion radon barrier systems. 59 references, 45 figures, 36 tables

On the Recent Use of Membrane Technology for Olive Mill Wastewater Purification

OpenAIRE

Ochando-Pulido, Javier Miguel; Martinez-Ferez, Antonio

2015-01-01

Many reclamation treatments as well as integrated processes for the purification of olive mill wastewaters (OMW) have already been proposed and developed but not led to completely satisfactory results, principally due to complexity or cost-ineffectiveness. The olive oil industry in its current status, composed of little and dispersed factories, cannot stand such high costs. Moreover, these treatments are not able to abate the high concentration of dissolved inorganic matter present in these h...

Application of the novel mill tailings agglomeration technology for prevention of acid mine drainage

International Nuclear Information System (INIS)

Amaratunga, L.M.

1994-01-01

Acid generation and subsequent liberation of heavy metals results from the surface disposal of sulfide mineral bearing mill tailings. Most Canadian base metals such as Ni, Cu, Zn, and Pb, as well as uranium and precious metal milling operations are producers of reactive mill tailings containing the major sulfide gangue minerals such as pyrite, pyrrhotite and arsenopyrites. A novel disposal technology by cold-bond tailings agglomeration process (CBTA) is currently being developed at Laurentian University. This process has been adapted to prevent acid mine drainage from reactive mill tailings. A preliminary study was undertaken to evaluate the application of the concept of agglomeration of reactive mill tailings using various alkaline binders and incorporating suitable chemical additives. The binders and additives are selected for their effectiveness in the prevention or retardation of the initial chemical and biochemical oxidation reactions of sulfide mineral leading to acid generation. Following a cold-bond, cold curing tailings agglomeration process, various types and dosages of chemical binders and their additives were employed. The additives under investigation were lime, sodium lauryl sulfate, potassium phosphate dibasic, sodium chloride and sodium benzoate. Some of these chemicals are well known acid neutralizers and others are inexpensive anionic surfactants, detergents and fertilizers acting as bactericides. Most of these additives have been reported in the literature as effective chemical agents used in the prevention and control of acid mine drainage from sulfide minerals. The paper also presents a leachate study to investigate the acid generation potential from each batch of reactive tailings agglomerates containing various binders and non-toxic additives

Asphalt emulsion radon barrier systems for uranium mill tailings: an overview of the technology

Energy Technology Data Exchange (ETDEWEB)

Baker, E.G.; Hartley, J.N.; Freeman, H.D.; Gates, T.E.; Nelson, D.A.; Dunning, R.L.

1984-03-01

Pacific Northwest Laboratory (PNL), under contract to the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project (UMTRAP) office, has developed an asphalt emulsion cover system to reduce the release of radon from uranium mill tailings. The system has been field tested at Grand Junction, Colorado. Results from laboratory and field tests indicate that this system is effective in reducing radon release to near-background levels (<2.5 pCi m/sup -2/s/sup -1/) and has the properties required for long-term effectiveness and stability. Engineering specifications have been developed, and analysis indicates that asphalt emulsion covers are cost-competitive with other cover systems. This report summarizes the technology for asphalt emulsion radon barrier systems. 59 references, 45 figures, 36 tables.

Toward the complete utilization of rice straw: Methane fermentation and lignin recovery by a combinational process involving mechanical milling, supporting material and nanofiltration.

Science.gov (United States)

Sasaki, Kengo; Okamoto, Mami; Shirai, Tomokazu; Tsuge, Yota; Fujino, Ayami; Sasaki, Daisuke; Morita, Masahiko; Matsuda, Fumio; Kikuchi, Jun; Kondo, Akihiko

2016-09-01

Rice straw was mechanically milled using a process consuming 1.9MJ/kg-biomass, and 10g/L of unmilled or milled rice straw was used as the carbon source for methane fermentation in a digester containing carbon fiber textile as the supporting material. Milling increased methane production from 226 to 419mL/L/day at an organic loading rate of 2180mg-dichromate chemical oxygen demand/L/day, corresponding to 260mLCH4/gVS. Storage of the fermentation effluent at room temperature decreased the weight of the milled rice straw residue from 3.81 to 1.00g/L. The supernatant of the effluent was subjected to nanofiltration. The black concentrates deposited on the nanofiltration membranes contained 53.0-57.9% lignin. Solution nuclear magnetic resonance showed that lignin aromatic components such as p-hydroxyphenyl (H), guaiacyl (G), and syringyl (S) were retained primarily, and major lignin interunit structures such as the β-O-4-H/G unit were absent. This combinational process will aid the complete utilization of rice straw. Copyright © 2016. Published by Elsevier Ltd.

Passivity of the bars manufactured using current technologies: laser-sintering, casting, and milling

Science.gov (United States)

Popescu, Diana; Popescu, Sabin; Pop, Daniel; Jivanescu, Anca; Todea, Carmen

2014-01-01

Implant overdentures are often selected as therapeutic options for the treatment of edentulous mandibles. "Passive-fit" between the mesostructures and the implants plays an important role in the longevity of the implant-prosthetic assembly in the oral cavity. "Mis-fit" can cause mechanical or biological complications. The purpose of this test was to investigate the passive adaptation of the bars manufactured through different technologies, and in this respect two bars (short and long) were fabricated by each process: laser-sintering, milling, casting. The tensions induced by tightening the connection screw between the bars and the underlying implants were recorded using strain gauges and used as measuring and comparing tool in testing the bars' "passivity". The results of the test showed that the milled bars had the best "passive-fit", followed by laser-sintered bars, while cast bars had the lowest adaptation level.

Beneficial uses of paper mill residuals for New York State`s recycled-paper mills. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

This report evaluates the New York paper mill industry in terms of the productive management and treatment of solid wastes. It identifies current efforts by recycling mills to beneficially use paper mill residuals (often called sludge) and suggests additional options that should be considered by the industry in general and individual mills in particular. It also examines the regulations and economics affecting the mills and suggests actions that could improve the industry`s ability to convert wastes to value-added products. The report recommends that the mills should continue measures to reduce fiber and filler clay losses, promote the transfer of usable fiber and clay to mills able to use them, upgrade sludge dewatering capabilities, and take a more regional approach to solid waste disposal problems. State agencies are urged to support these efforts, encourage the development and commercialization of new beneficial use technologies, and reduce regulatory barriers whenever possible.

Descriptive documentation for New Mexico uranium milling model

International Nuclear Information System (INIS)

Bonem, G.; Livevano, R.J.

1981-01-01

The New Mexico Uranium Milling Model is a linear programming model. It can demonstrate how cost minimizing management can reduce the costs of milling uranium subject to a series of environmental, resource, and technological constraints. For example, if 15,000 tons were the targeted level of milling output, the model would provide the minimum cost of this production level, given certain levels of environmental, fuel, water, and technological constraints. The model was developed to allow state policymakers to assess the uranium industry from various standpoints. Through the use of the model, state policymakers can determine the effects of air and water discharge standards and limited capital availability on: milling costs of production; uses of electricity, fuel, and water; and levels of air and water emissions. The model covers the following: process technologies which are acid leach and carbonate leach; raw materials mix; air and water discharges; residual treatment process; and plant types

Replacing chemicals in recycle mills with mechanical alternatives

Energy Technology Data Exchange (ETDEWEB)

Institute of Paper Science Technology

2002-07-01

A high-intensity spark fired underwater decomposes a small amount of the water into hydroxyl radicals, which are strong oxidants. These are able to oxidize contaminants such as glue and wood pitch that enter paper recycling mills as a part of the incoming furnish and cost the industry several hundred million dollars. The sparking technique is safe, inexpensive, and is capable of treating large volumes of water, which makes it attractive for mill applications. Several mill trials were run. Sparking caused a decrease in the tack of the deposits in one case. Lower bleach use occurred in two other mills; sparking reduced the degree of ink reattachment to fiber. The payback for either application is attractive. Sparking induced deposition of contaminants in another mill, which is a positive development--if it can be controlled. The technique is also able to degas water and to oxidize odor-causing sulfur compounds. Although one unit has been purchased by a mill, second-order effects caused by the technology needs to be defined further before the technology can be broadly applied.

Matrix model of the grinding process of cement clinker in the ball mill

Science.gov (United States)

Sharapov, Rashid R.

2018-02-01

In the article attention is paid to improving the efficiency of production of fine powders, in particular Portland cement clinker. The questions of Portland cement clinker grinding in closed circuit ball mills. Noted that the main task of modeling the grinding process is predicting the granulometric composition of the finished product taking into account constructive and technological parameters used ball mill and separator. It is shown that the most complete and informative characterization of the grinding process in a ball mill is a grinding matrix taking into account the transformation of grain composition inside the mill drum. Shows how the relative mass fraction of the particles of crushed material, get to corresponding fraction. Noted, that the actual task of reconstruction of the matrix of grinding on the experimental data obtained in the real operating installations. On the basis of experimental data obtained on industrial installations, using matrix method to determine the kinetics of the grinding process in closed circuit ball mills. The calculation method of the conversion of the grain composition of the crushed material along the mill drum developed. Taking into account the proposed approach can be optimized processing methods to improve the manufacturing process of Portland cement clinker.

GEOMETRICAL CHARACTERIZATION OF MICRO END MILLING TOOLS

DEFF Research Database (Denmark)

Borsetto, Francesca; Bariani, Paolo

The milling process is one of the most common metal removal operation used in industry. This machining process is well known since the beginning of last century and has experienced, along the years, many improvements of the basic technology, as concerns tools, machine tools, coolants/lubricants, ......The milling process is one of the most common metal removal operation used in industry. This machining process is well known since the beginning of last century and has experienced, along the years, many improvements of the basic technology, as concerns tools, machine tools, coolants....../lubricants, milling strategies and controls. Moreover the accuracy of tool geometry directly affects the performance of the milling process influencing the dimensional tolerances of the machined part, the surface topography, the chip formation, the cutting forces and the tool-life. The dimensions of certain...... geometrical details, as for instance the cutting edge radius, are determined by characteristics of the manufacturing process, tool material, coating etc. While for conventional size end mills the basic tool manufacturing process is well established, the reduction of the size of the tools required...

Technological project of serpentine raw material milling from Dobšiná heaps

Directory of Open Access Journals (Sweden)

Alena Pietriková

2005-11-01

Full Text Available Serpentine heaps in the surrounding of Dobšiná are an old ecological problem of the city and at the same time a suitable material for the production of MgCl2 and SiO2. The technology of the production is based on the chemical processing of the raw material, which is preceded by the raw material preparation comprising of the mechanical and hydraulic sorting, milling and the magnetic separation operations.

Management of wastes from uranium mines and mills

International Nuclear Information System (INIS)

Thomas, K.T.

1981-01-01

Uranium mining and milling operations have not given rise to much concern about their hazards, and with advancing technologies for mill processing and waste management, the situation will continue to improve. However, the disposal of large quantities of waste produced in mining and milling does have an environmental impact, owing to the long half-lives and the ready availability of the toxic radionuclides Ra-226 and Rn-222. This article deals with the management of wastes from uranium mines and mills

Parametric optimization of CNC end milling using entropy ...

African Journals Online (AJOL)

Parametric optimization of CNC end milling using entropy measurement technique combined with grey-Taguchi method. ... International Journal of Engineering, Science and Technology ... Keywords: CNC end milling, surface finish, material removal rate (MRR), entropy measurement technique, Taguchi method ...

Uranium mining and milling

International Nuclear Information System (INIS)

Floeter, W.

1976-01-01

In this report uranium mining and milling are reviewed. The fuel cycle, different types of uranium geological deposits, blending of ores, open cast and underground mining, the mining cost and radiation protection in mines are treated in the first part of this report. In the second part, the milling of uranium ores is treated, including process technology, acid and alkaline leaching, process design for physical and chemical treatment of the ores, and the cost. Each chapter is clarified by added figures, diagrams, tables, and flowsheets. (HK) [de

EFFECT OF MILLING SOFTNESS ON BASIC TECHNOLOGICAL PARAMETERS OF WORT

Directory of Open Access Journals (Sweden)

Ján Mareček

2011-02-01

Full Text Available Crushing the malted grain in the process of milling enables extractive substances of malt to become available for water which accelerates dissolving and other chemical and physical processes during the time of mashing. The aim of this work was at the basis of performed analyses to evaluate to what extent the grist composition with regard to different proportion of meal fraction affects the amount of extract and other technological parameters of malt. Analyzed malt was made from four varieties of malting barley as are Nitran, Ebson, Malz and Xanadu coming from the harvest year 2009. Composition of malt grist in great extent influenced the entire process of mashing, lautering and the amount of extract. The highest values of extract were measured by all varieties at the variant III. with the highest content (50% of the softest fraction meal + powder meal. The difference between variant I. with 10% content of the softest fraction and variant III. with 50% content, was already 3%. The most significant increase of this parameter was found out by varieties Ebson and Malz. Mashing and lautering parameters have not been significantly influenced by the milling variants. More significant differences were found out with regard to wort turbidity. Only variety Malz showed out the turbidity up to 4 EBC units, measured by turbidity meter under the angle 90°. The highest turbidity was measured by variant I. with the lowest proportion of the fraction meal + powder meal.doi:10.5219/111

Colorado's prospectus on uranium milling

International Nuclear Information System (INIS)

Hazle, A.J.; Franz, G.A.; Gamewell, R.

1982-01-01

The first part of this paper will discuss Colorado's control of uranium mill tailings under Titles I and II of the Uranium Mill Tailings Radiation Control Act of 1978. Colorado has a legacy of nine inactive mill sites requiring reclamation under Title I, and two presently active plus a number of new mill proposals which must be regulated in accordance with Title II. Past failures in siting and control on the part of federal jurisdictions have left the state with a heavy legacy requiring extensive effort to address impacts to the state's environment and population. The second part of this paper will discuss the remedial action programme authorized under Public Law 92-314 for Mesa Country, where lack of federal control led to the dispersal of several hundred thousand tons of uranium mill tailings on thousands of properties, including hundreds of homes, schools and other structures. Successful completion of the State efforts under both programmes will depend on a high level of funding and on the maintenance of adequate regulatory standards. (author)

Clean Fuel, Clean Energy Conversion Technology: Experimental and Numerical Investigation of Palm Oil Mill Effluent Biogas Flameless Combustion

Directory of Open Access Journals (Sweden)

Seyed Ehsan Hosseini

2015-08-01

Full Text Available The combustion of effluent biogas from a palm oil mill is not feasible on a large scale because of its low calorific value (LCV. Therefore, the captured biogas is usually flared because of a lack of appropriate combustion technology. However, such biogas could be an excellent source of energy for combined heat and power (CHP generation in palm oil mills. In this paper, the feasibility of using biogas from palm oil mills in flameless combustion systems is investigated. In computational fluid dynamic (CFD modeling, a two-step reaction scheme is employed to simulate the eddy dissipation method (EDM. In such biogas flameless combustion, the temperature inside the chamber is uniform and hot spots are eliminated. The peak of the non-luminous flame volume and the maximum temperature uniformity occur under stoichiometric conditions when the concentration of oxygen in the oxidizer is 7%. In these conditions, as the concentration of oxygen in the oxidizer increases, the efficiency of palm oil mill effluent biogas flameless combustion increases. The maximum efficiency (around 61% in the experiment is achieved when the percentage of oxygen in the oxidizer is 7%.

Soil Carbon 4 per mille

Science.gov (United States)

Minasny, Budiman; van Wesemael, Bas

2017-04-01

The '4 per mille Soils for Food Security and Climate' was launched at the COP21 aiming to increase global soil organic matter stocks by 4 per mille (or 0.4 %) per year as a compensation for the global emissions of greenhouse gases by anthropogenic sources. This paper surveyed the soil organic carbon (SOC) stock estimates and sequestration potentials from 20 regions in the world (New Zealand, Chile, South Africa, Australia, Tanzania, Indonesia, Kenya, Nigeria, India, China Taiwan, South Korea, China Mainland, United States of America, France, Canada, Belgium, England & Wales, Ireland, Scotland, and Russia) and asked whether the 4 per mille initiative is feasible. This study highlights region specific efforts and scopes for soil carbon sequestration. Reported soil C sequestration rates generally show that under best management practices, 4 per mille or even higher sequestration rates can be accomplished. High C sequestration rates (up to 10 per mille) can be achieved for soils with low initial SOC stock (topsoil less than 30 t C ha-1), and at the first twenty years after implementation of best management practices. In addition, areas that have reached equilibrium but not at their saturation level will not be able to further increase their sequestration. We found that most studies on SOC sequestration globally only consider topsoil (up to 0.3 m depth), as it is considered to be most affected by management techniques. The 4 per mille initiative was based on a blanket calculation of the whole global soil profile C stock, however the potential to increase SOC is mostly on managed agricultural lands. If we consider 4 per mille on global topsoil of agricultural land, SOC sequestration is about 3.6 Gt C per year, which effectively offset 40% of global anthropogenic greenhouse gas emissions. As a strategy for climate change mitigation, soil carbon sequestration buys time over the next ten to twenty years while other effective sequestration and low carbon technologies become

Predictors of Associate's Degree Completion in Engineering and Engineering Technologies

Science.gov (United States)

Reys-Nickel, Lynsey L.

The purpose of this ex post facto study was to describe completers and non-completers of associate's degree programs in engineering and engineering technologies and determine whether and to what extent completion in these programs is a function of selected student-related variables and institutional variables. Data from the 2004/2009 Beginning Postsecondary Students Longitudinal Study (BPS: 04/09) of associate's degree completers and non-completers in engineering and engineering technologies were accessed and analyzed through PowerStats, a web-based data analysis tool from National Center for Education Statistics (NCES). Descriptive data indicated that, proportionally, engineering and engineering technologies completers were mostly White, married, middle income, employed part-time, enrolled full-time, did not hold a high school diploma or certificate, completed Trigonometry/Algebra II, had a father who's highest education level was an associate's degree, but did not know their mother's highest level of education, completed remedial coursework, and started college with the goal of earning an associate's degree. While more males enrolled in the programs, males and females demonstrated similar completion rates, proportionally--with females showing a slightly higher percentage of completion. Results from the logistic regression further indicated that the variables significant to completion in associate's degree programs in engineering and engineering technologies were gender and enrollment size. Findings suggested that female students were more likely to earn the degree, and that the larger the institution, the more likely the student would become a completer. However, since a major limitation of the study was the small weighted sample size, the results of the study are inconclusive in terms of the extent to which the findings can be generalized to the population of students in associate's degree programs in engineering and engineering technologies. This study fills a

STIMULATION TECHNOLOGIES FOR DEEP WELL COMPLETIONS

Energy Technology Data Exchange (ETDEWEB)

Stephen Wolhart

2003-06-01

The Department of Energy (DOE) is sponsoring a Deep Trek Program targeted at improving the economics of drilling and completing deep gas wells. Under the DOE program, Pinnacle Technologies is conducting a project to evaluate the stimulation of deep wells. The objective of the project is to assess U.S. deep well drilling & stimulation activity, review rock mechanics & fracture growth in deep, high pressure/temperature wells and evaluate stimulation technology in several key deep plays. Phase 1 was recently completed and consisted of assessing deep gas well drilling activity (1995-2007) and an industry survey on deep gas well stimulation practices by region. Of the 29,000 oil, gas and dry holes drilled in 2002, about 300 were drilled in the deep well; 25% were dry, 50% were high temperature/high pressure completions and 25% were simply deep completions. South Texas has about 30% of these wells, Oklahoma 20%, Gulf of Mexico Shelf 15% and the Gulf Coast about 15%. The Rockies represent only 2% of deep drilling. Of the 60 operators who drill deep and HTHP wells, the top 20 drill almost 80% of the wells. Six operators drill half the U.S. deep wells. Deep drilling peaked at 425 wells in 1998 and fell to 250 in 1999. Drilling is expected to rise through 2004 after which drilling should cycle down as overall drilling declines.

Comparison of high pressure homogenization and stirred bead milling for the production of nano-crystalline suspensions.

Science.gov (United States)

Nakach, Mostafa; Authelin, Jean-René; Perrin, Marc-Antoine; Lakkireddy, Harivardhan Reddy

2018-05-19

Currently, the two technologies primarily used for the manufacturing of nano-crystalline suspensions using top down process (i.e. wet milling) are high pressure homogenization (HPH) and stirred bead milling (SBM). These two technologies are based upon different mechanisms, i.e., cavitation forces for HPH and shear forces for stirred bead milling. In this article, the HPH and SBM technologies are compared in terms of the impact of the suspension composition the process parameters and the technological configuration on milling performances and physical quality of the suspensions produced. The data suggested that both HPH and SBM are suitable for producing nano-crystalline suspensions, although SBM appeared more efficient than HPH, since the limit of milling (d 50 ) for SBM was found to be lower than that obtained with HPH (100 nm vs 200 nm). For both these technologies, regardless of the process parameters used for milling and the scale of manufacturing, the relationship of d 90 versus d 50 could be described by a unique master curve (technology signature of milling pathway) outlining that the HPH leads to more uniform particle size distribution as compared to SBM. Copyright © 2018 Elsevier B.V. All rights reserved.

Milling technological experiments to reduce Fusarium toxin contamination in wheat

Directory of Open Access Journals (Sweden)

Véha A.

2015-01-01

Full Text Available We examine 4 different DON-toxin-containing (0.74 - 1.15 - 1.19 - 2.14 mg/kg winter wheat samples: they were debranned and undebranned, and we investigated the flour’s and the by-products’ (coarse, fine bran toxin content changes. SATAKE lab-debranner was used for debranning and BRABENDER lab-mill for the milling process. Without debranning, two sample flours were above the DON toxin limit (0.75 mg/kg, which are waste. By minimum debranning (and minimum debranning mass loss; 6-8%, our experience with whole flour is that the multi-stage debranning measurement significantly reduces the content of the flour’s DON toxin, while the milling by-products, only after careful consideration and DON toxin measurements, may be produced for public consumption and for feeding.

Stimulation Technologies for Deep Well Completions

Energy Technology Data Exchange (ETDEWEB)

Stephen Wolhart

2005-06-30

The Department of Energy (DOE) is sponsoring the Deep Trek Program targeted at improving the economics of drilling and completing deep gas wells. Under the DOE program, Pinnacle Technologies conducted a study to evaluate the stimulation of deep wells. The objective of the project was to review U.S. deep well drilling and stimulation activity, review rock mechanics and fracture growth in deep, high-pressure/temperature wells and evaluate stimulation technology in several key deep plays. This report documents results from this project.

A novel fabrication technology of in situ TiB2/6063Al composites: High energy ball milling and melt in situ reaction

International Nuclear Information System (INIS)

Zhang, S.-L.; Yang, J.; Zhang, B.-R.; Zhao, Y.-T.; Chen, G.; Shi, X.-X.; Liang, Z.-P.

2015-01-01

Highlights: • This paper presents a novel technology to fabricate the TiB 2 /6063Al composites. • The novel technology decreases in situ reaction temperature and shortens the time. • The reaction mechanism of in situ reaction at the low temperature is discussed. • Effect of ball milling time and in situ reaction time on the composites is studied. - Abstract: TiB 2 /6063Al matrix composites are fabricated from Al–TiO 2 –B 2 O 3 system by the technology combining high energy ball milling with melt in situ reaction. The microstructure and tensile properties of the composites are investigated by XRD, SEM, EDS, TEM and electronic tensile testing. The results indicate that high energy ball milling technology decreases the in situ reaction temperature and shortens the reaction time for Al–TiO 2 –B 2 O 3 system in contrast with the conventional melt in situ synthesis. The morphology of in situ TiB 2 particles is exhibited in irregular shape or nearly circular shape, and the average size of the particles is less than 700 nm, thereinto the minimum size is approximately 200 nm. In addition, the morphology and size of the reinforced particles are affected by the time of ball milling and in situ reaction. TEM images indicate that the interface between 6063Al matrix and TiB 2 particles is clear and no interfacial outgrowth is observed. Tensile testing results show that the as-cast TiB 2 /6063Al composites exhibit a much higher strength, reaching 191 MPa, which is 1.23 times as high as the as-cast 6063Al matrix. Besides, the tensile fracture surface of the composites displays the dimple-fracture character

Jaduguda uranium mill : rich experiences for future challenges

International Nuclear Information System (INIS)

Beri, K.K.

1991-01-01

India's only uranium milling plant at Jaduguda was commissioned in 1967-68 utilising low grade uranium ore. The flowsheet of the mill and controlling parameters were based on studies done on laboratory and pilot plant scale tests at the Bhabha Atomic Research Centre, Bombay. The mill has worked upto expectation except in few areas where modifications had to be done for smooth production. Apart from this improvements in operating practices have been done based on experience gained in operating the mill, incorporating the recent technological advances. In the recent past, the mill was expanded to increase the installed capacity by 40% and was commissioned in October 1987. The expanded mill has given the desired capacity and is working smoothly. The present paper deals with the experience gained in running the plant for the last 20 years and changes incorporated (author). 4 figs

Stimulation Technologies for Deep Well Completions

Energy Technology Data Exchange (ETDEWEB)

None

2003-09-30

The Department of Energy (DOE) is sponsoring the Deep Trek Program targeted at improving the economics of drilling and completing deep gas wells. Under the DOE program, Pinnacle Technologies is conducting a study to evaluate the stimulation of deep wells. The objective of the project is to assess U.S. deep well drilling & stimulation activity, review rock mechanics & fracture growth in deep, high pressure/temperature wells and evaluate stimulation technology in several key deep plays. An assessment of historical deep gas well drilling activity and forecast of future trends was completed during the first six months of the project; this segment of the project was covered in Technical Project Report No. 1. The second progress report covers the next six months of the project during which efforts were primarily split between summarizing rock mechanics and fracture growth in deep reservoirs and contacting operators about case studies of deep gas well stimulation.

3D technology in fine art and craft exploring 3D printing, scanning, sculpting and milling

CERN Document Server

Mongeon, Bridgette

2015-01-01

The possibilities for creation are endless with 3D printing, sculpting, scanning, and milling, and new opportunities are popping up faster than artists can keep up with them. 3D Technology in Fine Art and Craft takes the mystery out of these exciting new processes by demonstrating how to navigate their digital components and showing their real world applications. Artists will learn to incorporate these new technologies into their studio work and see their creations come to life in a physical form never before possible. Featuring a primer on 3D basics for beginners,interviews, tutorials, and ar

Wastes from former mining and milling activities in Tajikistan

International Nuclear Information System (INIS)

Mirsaidov, U.M.

2012-01-01

This article is devoted to wastes from former mining and milling activities in Tajikistan. Currently, the serious radiological and ecological problems in Tajikistan are uranium mining and milling activities consequences overcoming which intensively developed during the soviet period. After the collapse of USSR, the uranic ores extraction in Tajikistan stopped due to deposit's output completion on the territory of the republic. Remediation of mining and milling activities' sites became the most urgent once all mines were closed.

A novel fabrication technology of in situ TiB{sub 2}/6063Al composites: High energy ball milling and melt in situ reaction

Energy Technology Data Exchange (ETDEWEB)

Zhang, S.-L.; Yang, J. [School of Materials Science and Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013 (China); Zhang, B.-R. [School of Mechanical Engineering, Qilu University of Technology, Jinan, Shandong 250022 (China); Zhao, Y.-T., E-mail: 278075525@qq.com [School of Materials Science and Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013 (China); Chen, G.; Shi, X.-X.; Liang, Z.-P. [School of Materials Science and Engineering, Jiangsu University, Zhenjiang, Jiangsu 212013 (China)

2015-08-05

Highlights: • This paper presents a novel technology to fabricate the TiB{sub 2}/6063Al composites. • The novel technology decreases in situ reaction temperature and shortens the time. • The reaction mechanism of in situ reaction at the low temperature is discussed. • Effect of ball milling time and in situ reaction time on the composites is studied. - Abstract: TiB{sub 2}/6063Al matrix composites are fabricated from Al–TiO{sub 2}–B{sub 2}O{sub 3} system by the technology combining high energy ball milling with melt in situ reaction. The microstructure and tensile properties of the composites are investigated by XRD, SEM, EDS, TEM and electronic tensile testing. The results indicate that high energy ball milling technology decreases the in situ reaction temperature and shortens the reaction time for Al–TiO{sub 2}–B{sub 2}O{sub 3} system in contrast with the conventional melt in situ synthesis. The morphology of in situ TiB{sub 2} particles is exhibited in irregular shape or nearly circular shape, and the average size of the particles is less than 700 nm, thereinto the minimum size is approximately 200 nm. In addition, the morphology and size of the reinforced particles are affected by the time of ball milling and in situ reaction. TEM images indicate that the interface between 6063Al matrix and TiB{sub 2} particles is clear and no interfacial outgrowth is observed. Tensile testing results show that the as-cast TiB{sub 2}/6063Al composites exhibit a much higher strength, reaching 191 MPa, which is 1.23 times as high as the as-cast 6063Al matrix. Besides, the tensile fracture surface of the composites displays the dimple-fracture character.

Ball-milling-induced crystallization and ball-milling effect on thermal crystallization kinetics in an amorphous FeMoSiB alloy

International Nuclear Information System (INIS)

Guo, F.Q.; Lu, K.

1997-01-01

Microstructure evolution in a melt-spun amorphous Fe 77.2 Mo 0.8 Si 9 B 13 alloy subjected to high-energy ball milling was investigated by means of X-ray diffraction (XRD), a transmission electron microscope (TEM), and a differential scanning calorimeter (DSC). It was found that during ball milling, crystallization occurs in the amorphous ribbon sample with precipitation of an α-Fe solid solution, and the amorphous sample crystallizes completely into a single α-Fe nanostructure (rather than α-Fe and borides as in the usual thermal crystallization products) when the milling time exceeds 135 hours. The volume fraction of material crystallized was found to be approximately proportional to the milling time. The fully crystallized sample with a single α-Fe nanophase exhibits an intrinsic thermal stability against phase separation upon annealing at high temperatures. The ball-milling effect on the subsequent thermal crystallization of the amorphous phase in an as-milled sample was studied by comparison of the crystallization products and kinetic parameters between the as-quenched amorphous sample and the as-milled sample was studied by comparison of the crystallization products and kinetic parameters between the as-quenched amorphous sample and the as-milled partially crystallized samples. The crystallization temperatures and activation energies for the crystallization processes of the residual amorphous phase were considerably decreased due to ball milling, indicating that ball milling has a significant effect on the depression of thermal stability of the residual amorphous phase

Effect of the milling conditions on the degree of amorphization of selenium by milling in a planetary ball mill

International Nuclear Information System (INIS)

Ksiazek, K; Wacke, S; Gorecki, T; Gorecki, Cz

2007-01-01

The effect of the milling parameters (rotation speed of the milling device and duration of milling) on the phase composition of the products of milling of fully crystalline selenium has been investigated. The milling was conducted using a planetary micromill and the phase composition of the milling products was determined by differential thermal analysis. It has been found that ball milling leads to the partial amorphization of the starting crystalline material. The content of amorphous phase in the milling products depends, in a rather complicated way, on the milling parameters. At the milling parameters adopted in the present study, the milling product was never fully amorphous. The complicated way the milling parameters affect the content of amorphous phase in the milling products is a result of competition of two processes: amorphization due to deformation and refinement of grains of milled material and crystallization of the already produced amorphous material at the cost of heat evolved in the milling vial during the milling process

Practitioner Profile: An Interview With Amanda Mills

Directory of Open Access Journals (Sweden)

Amanda Mills

2012-01-01

Full Text Available For more than 25 years, Amanda Mills has been working with arts organizations across Canada and with artists of all kinds to assist them in achieving financial sanity. She has taught business management at the University of Victoria and has prepared thousands of tax returns for writers, visual artists, choreographers, actors, filmmakers, broadcasters, and creative entrepreneurs. Ten years ago, bringing together her work on trauma, with twenty years of business management, Mills founded Loose Change Financial Therapy – the place where money and feelings meet. Mills has presented Loose Change workshops for social workers, teachers, psychotherapists, artists, anti-poverty activists, sex trade workers, women’s groups, and the general public.  She has been a guest on major Canadian radio and television broadcasts and profiled in many major Canadian newspapers and periodicals. Mills is also a crisis counselor and co-wrote a bestselling book on recovering from trauma. A tax professional and business manager, she is certified as a financial counselor under the Bankruptcy and Insolvency Act. Mills is also currently completing a certificate in mediation.

Sustainable technologies for olive mill wastewater management (abstract)

Science.gov (United States)

The California olive oil industry produces more than 600 million gallons of wastewater each year. Olive mill wastewater (OMWW) is considered a highly polluting effluent due to its high organic load and resistance to biological degradation. A current trend in OMWW management is to not only decrease e...

Peculiarities of binding composition production in vortex jet mill

Science.gov (United States)

Zagorodnyuk, L. Kh; Lesovik, V. S.; Sumskoy, D. A.; Elistratkin, M. Yu; Makhortov, D. S.

2018-03-01

The article investigates the disintegration of perlite production waste in a vortex jet mill; the regularities of milling were established. Binding compositions were obtained at different ratios of cement vs. perlite sand production waste in the vortex jet mill in various milling regimes. The peculiarities of milling processes were studied, and technological and physicomechanical properties of the binding compositions were determined as well. The microstructure of the cement stones made of activated Portland cement and binding compositions in the vortex jet mill was elucidated by electron microscopy. The open pores of the cement-binding compositions prepared using perlite fillers were found to be filled by newgrowths at different stages of collective growth. The microstructure of the binding compositions is dense due to rationally proportioned composition, effective mineral filler— perlite waste — that creates additional substrates for internal composite microstructure formation, mechanochemical activation of raw mixture, which allows obtaining composites with required properties.

Uranium ore mill at Dolni Rozinka: 40 years of operation

International Nuclear Information System (INIS)

Toman, F.; Jezova, V.

2007-01-01

Uranium ore mined in the Rozna deposit is treated at a chemical treatment plant (a mill) situated in the close vicinity of the Rozna mine. In the mill, uranium is extracted from the crushed and ground-up ore by alkaline leaching. Uranium is then recovered from the solution by sorption on ion exchange resin; the next steps are precipitation and drying. Alkaline leaching is applied at the atmospheric pressure and the temperature of 80 deg C; the recovery factor is moving around 93%. The final product of the milling is uranium concentrate, ammonium diuranate (NH 4 ) 2 U 2 O 7 ), a so-called 'yellow cake' which is treated into a fuel for nuclear power plants in conversion facilities abroad. The milling is carried on under the condition of the closed cycle of technology water. Due to the positive annual precipitation balance, the over balance of technology water in tailings pond has to be purified before discharging into a river. Evaporation and membrane processes (electrodialysis and reverse osmosis) are used to purify the water. The mill at Dolni Rozinka has been in operation since 1968. It has processed 13.2 million tons of uranium ore which is about 14000 tons of uranium and purified more than 6 million m 3 of the over balanced technology water during 40 years. From the organizational point of view, the mine and the chemical treatment plant form the branch plant GEAM, which is a part of the state enterprise DIAMO. (author)

New technology for recycling materials from oily cold rolling mill sludge

Institute of Scientific and Technical Information of China (English)

Bo Liu; Shen-gen Zhang; Jian-jun Tian; De-an Pan; Ling Meng; Yang Liu

2013-01-01

Oily cold rolling mill (CRM) sludge is one of metallurgical industry solid wastes. The recycle of these wastes can not only protect the environment but also permit their reutilization. In this research, a new process of“hydrometallurgical treatment+hydrothermal synthesis”was investigated for the combined recovery of iron and organic materials from oily CRM sludge. Hydrometallurgical treatment, mainly including acid leaching, centrifugal separation, neutralization reaction, oxidizing, and preparation of hydrothermal reaction precursor, was first utilized for processing the sludge. Then, micaceous iron oxide (MIO) pigment powders were prepared through hydrothermal reaction of the obtained precursor in alkaline media. The separated organic materials can be used for fuel or chemical feedstock. The quality of the prepared MIO pigments is in accordance with the standards of MIO pigments for paints (ISO 10601-2007). This clean, eff ective, and economical technology off ers a new way to recycle oily CRM sludge.

Automatic in-process chatter avoidance in the high-speed milling process

NARCIS (Netherlands)

Dijk, van N.J.M.; Doppenberg, E.J.J.; Faassen, R.P.H.; Wouw, van de N.; Oosterling, J.A.J.; Nijmeijer, H.

2010-01-01

High-speed milling is often used in industry to maximize productivity of the manufacturing of high-technology components, such as aeronautical components, mold, and dies. The occurrence of chatter highly limits the efficiency and accuracy of high-speed milling operations. In this paper, two control

Einstein-Yang-Mills-Lorentz black holes

Energy Technology Data Exchange (ETDEWEB)

Cembranos, Jose A.R.; Gigante Valcarcel, Jorge [Universidad Complutense de Madrid, Departamento de Fisica Teorica I, Madrid (Spain)

2017-12-15

Different black hole solutions of the coupled Einstein-Yang-Mills equations have been well known for a long time. They have attracted much attention from mathematicians and physicists since their discovery. In this work, we analyze black holes associated with the gauge Lorentz group. In particular, we study solutions which identify the gauge connection with the spin connection. This ansatz allows one to find exact solutions to the complete system of equations. By using this procedure, we show the equivalence between the Yang-Mills-Lorentz model in curved space-time and a particular set of extended gravitational theories. (orig.)

Research on the characterization and conditioning of uranium mill tailings. III. Summary of uranium mill tailings conditioning research and implications regarding remedial actions

International Nuclear Information System (INIS)

Dreesen, D.R.; Cokal, E.J.; Thode, E.F.; Williams, J.M.

1983-06-01

This report summarizes the findings of research on uranium mill tailings conditioning technology development performed for the Department of Energy's (DOE) Uranium Mill Tailings Remedial Action Project (UMTRAP). Hazards and risks posed by tailings piles are discussed in relation to the goal of conditioning the tailings to reduce these hazards. The results of our efforts regarding characterization of tailings, removal of radionuclides, mineral recovery, thermal stabilization, and engineering/economic analysis of conditioning are presented. The implications of these results for remedial action plans are discussed and conclusions regarding the applicability of these technologies are also presented

Uranium milling costs

International Nuclear Information System (INIS)

Coleman, R.B.

1980-01-01

Basic process flowsheets are reviewed for conventional milling of US ores. Capital costs are presented for various mill capacities for one of the basic processes. Operating costs are shown for various mill capacities for all of the basic process flowsheets. The number of mills using, or planning to use, a particular process is reviewed. A summary of the estimated average milling costs for all operating US mills is shown

New Nanoparticles Dispersing Beads Mill with Ultra Small Beads and its Application

International Nuclear Information System (INIS)

Inkyo, M; Tahara, T; Imajyo, Y

2011-01-01

Two of the major problems related to nanoparticle dispersion with a conventional beads mill are re-agglomeration and damage to the crystalline structure of the particles. The Ultra Apex Mill was developed to solve these problems by enabling the use of ultra-small beads with a diameter of less than 0.1mm. The core of this breakthrough development is centrifugation technology which allows the use of beads as small as 0.015mm. When dispersing agglomerated nanoparticles the impulse of the small beads is very low which means there is little influence on the particles. The surface energy of the nanoparticles remains low so the properties are not likely to change. As a result, stable nanoparticle dispersions can be achieved without re-cohesion. The Ultra Apex Mill is superior to conventional beads mills that are limited to much larger bead sizes. The technology of the Ultra Apex Mill has pioneered practical applications for nanoparticles in various fields: composition materials for LCD screens, ink-jet printing, ceramic condensers and cosmetics.

Pilot scale hybrid processes for olive mill wastewater treatment, energy production and water reuse: comparison between fungal and electro-coagulation pre-treatments

International Nuclear Information System (INIS)

Sayadi, S.

2009-01-01

Olive oil mill wastewaters (OMW) cause disposal problems because they contain powerful pollutants such as phenolic compounds. Complete biodegradation or removal of these compounds is hardly achieved by a single treatment method. In this work, we investigated 2 integrated technologies for the treatment of the recalcitrant contaminants of OMW, allowing water recovery and reuse for agricultural purposes. (Author)

Pilot scale hybrid processes for olive mill wastewater treatment, energy production and water reuse: comparison between fungal and electro-coagulation pre-treatments

Energy Technology Data Exchange (ETDEWEB)

Sayadi, S.

2009-07-01

Olive oil mill wastewaters (OMW) cause disposal problems because they contain powerful pollutants such as phenolic compounds. Complete biodegradation or removal of these compounds is hardly achieved by a single treatment method. In this work, we investigated 2 integrated technologies for the treatment of the recalcitrant contaminants of OMW, allowing water recovery and reuse for agricultural purposes. (Author)

Control and prevention of seepage from uranium mill waste disposal facilities

International Nuclear Information System (INIS)

Williams, R.E.

1978-01-01

This paper constitutes an analysis of the technologies which are available for the prevention of movement of waste waters out of uranium mill waste disposal facilities via sub-surface routes. Hydrogeologic criteria for potential uranium mill waste disposal sites and mathematical modeling of contaminant migration in ground water are presented. Methods for prevention of seepage from uranium mill waste disposal facilities are investigated: liners, clay seals, synthetic polymeric membranes (PVC, polyethylene, chlorinated polyethylene, hypalon, butyl rubber, neoprene, elasticized polyolefin)

Radiation health and safety aspects in uranium milling

International Nuclear Information System (INIS)

Smart, B.C.

1982-01-01

This presentation deals mainly with radiation levels associated with the uranium milling operations, including yellowcake production. The regulation of uranium mills has not received much attention in the past because radiation levels have been generally low, and uranium milling has been substantially free of occupational illness. More attention is being directed towards minimizing exposures, and the Canadian Atomic Energy Control Board is working on new regulations which will reflect the recommendations of various hearings and the International Commission on Radiological Protection. Emphasis is now being placed on improving monitoring methods. At the beginning of 1982 a gamma dosimetry program will be put into effect for all uranium mine and mill workers. An improved method is also being sought to determine radon daughter exposures more accurately. It is expected that a better knowledge of monitoring and assessing thoron daughter levels in mine and mill facilities will be obtained soon. This radiation contribution will be included when calculating a combined radiation exposure factor for individual workers. Programs are underway to better monitor and assess uranium dust inhalation. Initial studies indicate that the present precautions taken to avoid dust inhalation at the mills are effective. A more complete study will be undertaken in 1982

Prototyping of Dental Structures Using Laser Milling

Science.gov (United States)

Andreev, A. O.; Kosenko, M. S.; Petrovskiy, V. N.; Mironov, V. D.

2016-02-01

The results of experimental studies of the effect of an ytterbium fiber laser radiation parameters on processing efficiency and quality of ZrO2 ceramics widely used in stomatology are presented. Laser operating conditions with optimum characteristics for obtaining high quality final surfaces and rapid material removal of dental structures are determined. The ability of forming thin-walled ceramic structures by laser milling technology (a minimum wall thickness of 50 μm) is demonstrated. The examples of three-dimensional dental structures created in computer 3D-models of human teeth using laser milling are shown.

A first experience with digital complete overdentures

Directory of Open Access Journals (Sweden)

Salwa Omar Bajunaid

2016-07-01

Full Text Available The development of computer-aided design/computer-aided manufacturing systems for dentistry in the 1980s resulted in the successful fabrication of crowns, fixed dental prostheses, and superstructures for both natural teeth and dental implants. Today, this technology is available for constructing digitally designed and milled, completely removable dental prostheses. The procedure uses clinical and laboratory protocols that allow fabrication of completely removable prostheses within two clinical appointments. The aim of this clinical report is to present the author’s first experience with digital complete overdentures, the practicality of this technology, and patient feedback. Compared with conventional overdentures, the fit of the digital prostheses was improved because the cameo and flanges of the prostheses were nicely shaped and rolled, and this enhanced their stability and retention. Occlusion was also excellent. However, aesthetics in terms of the alignment, shape, and size of the maxillary overdenture teeth were inacceptable. Despite some of the drawbacks identified in our study, the use of removable digital dentures does provide excellent adaptation of the denture base and requires fewer clinic visits. We anticipate that the unsatisfactory aesthetic outcomes presented in this report can be corrected with more experience. We also believe that acquiring an in-house scanning machine would be beneficial. We highly recommend including this technique in dental school curriculums at both the undergraduate and graduate levels in order to keep students and residents up to date on the latest technology available.

A first experience with digital complete overdentures.

Science.gov (United States)

Bajunaid, Salwa Omar

2016-07-01

The development of computer-aided design/computer-aided manufacturing systems for dentistry in the 1980s resulted in the successful fabrication of crowns, fixed dental prostheses, and superstructures for both natural teeth and dental implants. Today, this technology is available for constructing digitally designed and milled, completely removable dental prostheses. The procedure uses clinical and laboratory protocols that allow fabrication of completely removable prostheses within two clinical appointments. The aim of this clinical report is to present the author's first experience with digital complete overdentures, the practicality of this technology, and patient feedback. Compared with conventional overdentures, the fit of the digital prostheses was improved because the cameo and flanges of the prostheses were nicely shaped and rolled, and this enhanced their stability and retention. Occlusion was also excellent. However, aesthetics in terms of the alignment, shape, and size of the maxillary overdenture teeth were inacceptable. Despite some of the drawbacks identified in our study, the use of removable digital dentures does provide excellent adaptation of the denture base and requires fewer clinic visits. We anticipate that the unsatisfactory aesthetic outcomes presented in this report can be corrected with more experience. We also believe that acquiring an in-house scanning machine would be beneficial. We highly recommend including this technique in dental school curriculums at both the undergraduate and graduate levels in order to keep students and residents up to date on the latest technology available.

Environmental Development Plan: uranium mining, milling, and conversion

International Nuclear Information System (INIS)

1979-08-01

This Environmental Development Plan (EDP) identifies the planning and management requirements and schedules needed to evaluate and assess the environmental, health, and safety (EH and S) aspects of the uranium mining, milling, and conversion technologies. The plan represents the collective perceptions of EH and S concerns and requirements and knowledge of ongoing research programs of most of the Federal agencies involved in significant EH and S R and D program management, standards setting, or regulatory activities associated with uranium mining, milling, and conversion

A complete two-loop, five-gluon helicity amplitude in Yang-Mills theory

International Nuclear Information System (INIS)

Badger, Simon; Mogull, Gustav; Ochirov, Alexander; O’Connell, Donal

2015-01-01

We compute the integrand of the full-colour, two-loop, five-gluon scattering amplitude in pure Yang-Mills theory with all helicities positive, using generalized unitarity cuts. Tree-level BCJ relations, satisfied by amplitudes appearing in the cuts, allow us to deduce all the necessary non-planar information for the full-colour amplitude from known planar data. We present our result in terms of irreducible numerators, with colour factors derived from the multi-peripheral colour decomposition. Finally, the leading soft divergences are checked to reproduce the expected infrared behaviour.

A complete two-loop, five-gluon helicity amplitude in Yang-Mills theory

Energy Technology Data Exchange (ETDEWEB)

Badger, Simon; Mogull, Gustav; Ochirov, Alexander [Higgs Centre for Theoretical Physics, School of Physics and Astronomy, University of Edinburgh, Edinburgh EH9 3JZ, Scotland (United Kingdom); O’Connell, Donal [Higgs Centre for Theoretical Physics, School of Physics and Astronomy, University of Edinburgh, Edinburgh EH9 3JZ, Scotland (United Kingdom); Kavli Institute for Theoretical Physics, University of California, Santa Barbara, CA 93106-4030 (United States)

2015-10-09

We compute the integrand of the full-colour, two-loop, five-gluon scattering amplitude in pure Yang-Mills theory with all helicities positive, using generalized unitarity cuts. Tree-level BCJ relations, satisfied by amplitudes appearing in the cuts, allow us to deduce all the necessary non-planar information for the full-colour amplitude from known planar data. We present our result in terms of irreducible numerators, with colour factors derived from the multi-peripheral colour decomposition. Finally, the leading soft divergences are checked to reproduce the expected infrared behaviour.

Techno-economic and ex-ante environmental assessment of C6 sugars production from spruce and corn. Comparison of organosolv and wet milling technologies

NARCIS (Netherlands)

Moncada, Jonathan; Vural Gursel, Iris; Huijgen, Wouter J J; Dijkstra, Jan Wilco; Ramírez, Andrea

2018-01-01

This study assesses the techno-economic and environmental performance of C6 sugars production from softwood (spruce) and corn. Two technologies were considered in the assessment: organosolv of spruce woodchips (2nd generation) and corn wet milling (1st generation). Process models were developed to

Research on cutting vibration characteristics of face-milling involute gear

Directory of Open Access Journals (Sweden)

Chengzhe JIN

2017-10-01

Full Text Available Traditional machining methods, such as gear hobbing, gear shaping and gear milling, etc, are commonly used for cutting machining of gear tooth profile, which cannot meet huge machining demand of gears to a certain extent. This article proposes to utilize a face-milling machining method in involute gear machining, which can be used to reduce production cost effectively. Cutting vibration generated during cutting machining has a direct effect on the machining accuracy and machined surface quality of workpiece. Therefore, it is desiderated to perform in-depth research regarding this issue. ADAMS software was used to establish a rigid-flexible coupling virtual prototyping model of face-milling gear milling system and a cutting vibration system model. Cutting vibration analysis was performed for face-milling gear by adopting quick sine frequency sweep method, so that the frequency response characteristics of workpiece in three directions X, Y and Z and space were acquired. The research results will provide reference and theoretical foundation for actual application of face-milling gear machining technology.

Mill Designed Bio bleaching Technologies

Energy Technology Data Exchange (ETDEWEB)

Institute of Paper Science Technology

2004-01-30

generation of laccase has a broad spectrum of operating parameters. Nonetheless, the development of future genetically engineered laccases with enhanced temperature, pH and redox potentials will dramatically improve the overall process. A second challenge for LMS bleaching technologies is the need to develop effective, catalytic mediators. From the literature we already know this is feasible since ABTS and some inorganic mediators are catalytic. Unfortunately, the mediators that exhibit catalytic properties do not exhibit significant delignification properties and this is a challenge for future research studies. Potential short-term mill application of laccase has been recently reported by Felby132 and Chandra133 as they have demonstrated that the physical properties of linerboard can be improved when exposed to laccase without a chemical mediator. In addition, xxx has shown that the addition of laccase to the whitewater of the paper machine has several benefits for the removal of colloidal materials. Finally, this research program has presented important features on the delignification chemistry of LMS{sub NHA} and LMS{sub VA} that, in the opinion of the author, are momentous contributions to the overall LMS chemistry/biochemistry knowledge base which will continue to have future benefits.

Mechanical alloying and reactive milling in a high energy planetary mill

International Nuclear Information System (INIS)

Jiang Xianjin; Trunov, Mikhaylo A.; Schoenitz, Mirko; Dave, Rajesh N.; Dreizin, Edward L.

2009-01-01

Powder refinement in a planetary mill (Retsch PM 400-MA) is investigated experimentally and analyzed using discrete element modeling (DEM). Refinement is defined as the average size of the individual components in a composite powder. The specific milling dose, defined as the product of charge ratio and milling time, is used as an experimental parameter tracking the progress of the material refinement. This parameter is determined experimentally for milling of boron and titanium powders, for which the time of initiation of a self-sustained reaction is measured under different milling conditions. It is assumed that the reaction becomes self-sustaining when the same powder refinement is achieved. The DEM calculations established that the milling balls primarily roll along the milling container's perimeter. The inverse of the rate of energy dissipation resulting from this rolling motion is used as the DEM analog of the specific milling dose. The results correlate well with experimental observations.

Vertically and Horizontally Mounted Wind Mills : Wind Energy Production in Tampere University of Applied Sciences

OpenAIRE

Evdokimova, Ekaterina

2013-01-01

The purpose of this thesis was to gather information about vertical and horizontal wind mills and to complete a research on wind power production by wind mills which were installed in Tampere University of Applied Sciences. The horizontally mounted wind mill Windspot 3.5 and vertically mounted wind mill Cypress were installed in summer 2011 but they started functioning and supplying energy only during 2012. In the theoretical part of this thesis wind speed and wind power production is dis...

Yang-Mills correlation functions from integrable spin chains

International Nuclear Information System (INIS)

Roiban, Radu; Volovich, Anastasia

2004-01-01

The relation between the dilatation operator of N = 4 Yang-Mills theory and integrable spin chains makes it possible to compute the one-loop anomalous dimensions of all operators in the theory. In this paper we show how to apply the technology of integrable spin chains to the calculation of Yang-Mills correlation functions by expressing them in terms of matrix elements of spin operators on the corresponding spin chain. We illustrate this method with several examples in the SU(2) sector described by the XXX 1/2 chain. (author)

An introduction to Randell Mills' Grand Unified Theory of Classical Physics (GUT-CP) : an Eindhoven University of Technology Honors Program 2007-2008 research project

NARCIS (Netherlands)

van der Heijden, E.H.M.; van der Heijden, M.A.; Roosmalen, van J.; Verdonschot, S.; Kroesen, G.M.W.; Nijdam, S.

2008-01-01

This document represents the results of a year of research as part of the Honors Program of Eindhoven University of Technology. We heard about Randell L. Mills abandoning Quantum Mechanics and proposing an alternative theory. This sounded interesting enough to contact Gerrit M.W. Kroesen whose group

Identification of Technological Parameters of Ni-Alloys When Machining by Monolithic Ceramic Milling Tool

Science.gov (United States)

Czán, Andrej; Kubala, Ondrej; Danis, Igor; Czánová, Tatiana; Holubják, Jozef; Mikloš, Matej

2017-12-01

The ever-increasing production and the usage of hard-to-machine progressive materials are the main cause of continual finding of new ways and methods of machining. One of these ways is the ceramic milling tool, which combines the pros of conventional ceramic cutting materials and pros of conventional coating steel-based insert. These properties allow to improve cutting conditions and so increase the productivity with preserved quality known from conventional tools usage. In this paper, there is made the identification of properties and possibilities of this tool when machining of hard-to-machine materials such as nickel alloys using in airplanes engines. This article is focused on the analysis and evaluation ordinary technological parameters and surface quality, mainly roughness of surface and quality of machined surface and tool wearing.

Observables in topological Yang-Mills theories with extended shift supersymmetry

Energy Technology Data Exchange (ETDEWEB)

Constantinidis, Clisthenis P; Piguet, Olivier [Universidade Federal do Espirito Santo (UFES), Vitoria, ES (Brazil); Spalenza, Wesley [Scuola Internazionale Superiore di Studi Avanzati (SISSA), Trieste (Italy); Centro Brasileiro de Pesquisas Fsicas (CBPF), Rio de Janeiro (Brazil)

2006-01-01

We present a complete classification, at the classical level, of the observables of topological Yang-Mills theories with an extended shift supersymmetry of N generators, in any space-time dimension. The observables are defined as the Yang-Mills BRST cohomology classes of shift supersymmetry invariants. These cohomology classes turn out to be solutions of an N-extension of Witten's equivariant cohomology. This work generalizes results known in the case of shift supersymmetry with a single generator. (orig.)

Geothermal drilling and completion technology development program. Quarterly progress report, January-March 1980

Energy Technology Data Exchange (ETDEWEB)

Varnado, S.G. (ed.)

1980-04-01

The progress, status, and results of ongoing Research and Development (R and D) within the Geothermal Drilling and Completion Technology Development Program are described. The program emphasizes the development of geothermal drilling hardware, drilling fluids, completion technology, and lost circulation control methods. Advanced drilling systems are also under development. The goals of the program are to develop the technology required to reduce well costs by 25% by 1983 and by 50% by 1987.

Geometry of Yang-Mills fields

International Nuclear Information System (INIS)

Atiyah, M.F.

1978-01-01

In this talk I shall explain how information about classical solutions of Yang-Mills equations can be obtained, rather surprisingly, from algebraic geometry. Although direct physical interest is restricted to the case of four dimensions I shall begin by discussing the two-dimensional case. Besides preparing the ground for the four-dimensional problem this has independent mathematical (and possible physical) interest, and very complete results can be obtained. (orig.) [de

Microstructural evolution of nanostructured Ti0.9Al0.1N prepared by reactive ball-milling

International Nuclear Information System (INIS)

Bhaskar, U.K.; Bid, S.; Pradhan, S.K.

2011-01-01

Research highlights: → Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N powder has been prepared by ball-milling the 0.9 mol fraction of α-Ti (hcp) and 0.1 mol fraction of aluminum (fcc) powders under N 2 at room temperature. Initially, α-Ti phase partially transformed to the transient β-Ti phase and Ti 0.9 Al 0.1 N (fcc) phase is noticed to form after 3 h of milling. Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N phase is formed after 7 h of milling. The main features which are observed in the present study are stated below: 1.During ball-milling of α-Ti, the α-Ti phase partially converted to transient cubic β-Ti phase within 1 h of milling. 2.Ti 0.9 Al 0.1 N (fcc) phase is noticed to form after 3 h of milling. Complete formation of Ti 0.9 Al 0.1 N (fcc) is obtained at 7 h of milling which is lesser than complete formation time (9 h) of TiN. Doping Al atoms accelerates the formation of (TiAl)N phase. 3.The particle size of Ti 0.9 Al 0.1 N decrease rapidly up to 3 h and then increase slightly due to agglomeration effect. 4.The particle size of Ti 0.9 Al 0.1 N estimated from X-ray is in good agreement with that measured from HRTEM. - Abstract: Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N powder has been prepared by ball-milling the α-Ti (hcp) and aluminum (fcc) powders under N 2 at room temperature. Initially, α-Ti phase partially transformed to the transient cubic β-Ti phase and Ti 0.9 Al 0.1 N (fcc) phase is noticed to form after 3 h of milling. Nanocrystalline stoichiometric Ti 0.9 Al 0.1 N phase is formed after 7 h of milling. After 1 h of milling, all Al atoms are diffused into the α-Ti matrix. The transient β-Ti phase is noticed to form after 1 h of milling and disappears completely after 7 h of milling. Microstructure characterization of unmilled and ball-milled powders by analyzing XRD patterns employing the Rietveld structure refinement reveals the inclusion of Al and nitrogen atoms into the Ti lattice on the way to formation of Ti 0.9 Al 0.1 N

Bio-refinery system of DME or CH4 production from black liquor gasification in pulp mills.

Science.gov (United States)

Naqvi, M; Yan, J; Fröling, M

2010-02-01

There is great interest in developing black liquor gasification technology over recent years for efficient recovery of bio-based residues in chemical pulp mills. Two potential technologies of producing dimethyl ether (DME) and methane (CH(4)) as alternative fuels from black liquor gasification integrated with the pulp mill have been studied and compared in this paper. System performance is evaluated based on: (i) comparison with the reference pulp mill, (ii) fuel to product efficiency (FTPE) and (iii) biofuel production potential (BPP). The comparison with the reference mill shows that black liquor to biofuel route will add a highly significant new revenue stream to the pulp industry. The results indicate a large potential of DME and CH(4) production globally in terms of black liquor availability. BPP and FTPE of CH(4) production is higher than DME due to more optimized integration with the pulping process and elimination of evaporation unit in the pulp mill.

Fabrication of Biochips with Micro Fluidic Channels by Micro End-milling and Powder Blasting

Directory of Open Access Journals (Sweden)

Dong Sam Park

2008-02-01

Full Text Available For microfabrications of biochips with micro fluidic channels, a large number of microfabrication techniques based on silicon or glass-based Micro-Electro-Mechanical System (MEMS technologies were proposed in the last decade. In recent years, for low cost and mass production, polymer-based microfabrication techniques by microinjection molding and micro hot embossing have been proposed. These techniques, which require a proper photoresist, mask, UV light exposure, developing, and electroplating as a preprocess, are considered to have some problems. In this study, we propose a new microfabrication technology which consists of micro end-milling and powder blasting. This technique could be directly applied to fabricate the metal mold without any preprocesses. The metal mold with micro-channels is machined by micro end-milling, and then, burrs generated in the end-milling process are removed by powder blasting. From the experimental results, micro end-milling combined with powder blasting could be applied effectively for fabrication of the injection mold of biochips with micro fluidic channels.

Review of fugitive dust control for uranium mill tailings

International Nuclear Information System (INIS)

Li, C.T.; Elmore, M.R.; Hartley, J.N.

1983-01-01

An immediate concern associated with the disposal of uranium mill tailings is that wind erosion of the tailings from an impoundment area will subsequently deposit tailings on surrounding areas. Pacific Northwest Laboratory (PNL), under contract to the U.S. Nuclear Regulatory Commission, is investigating the current technology for fugitive dust control. Different methods of fugitive dust control, including chemical, physical, and vegetative, have been used or tested on mill tailings piles. This report presents the results of a literature review and discussions with manufacturers and users of available stabilization materials and techniques

Review of fugitive dust control for uranium mill tailings

Energy Technology Data Exchange (ETDEWEB)

Li, C.T.; Elmore, M.R.; Hartley, J.N.

1983-01-01

An immediate concern associated with the disposal of uranium mill tailings is that wind erosion of the tailings from an impoundment area will subsequently deposit tailings on surrounding areas. Pacific Northwest Laboratory (PNL), under contract to the U.S. Nuclear Regulatory Commission, is investigating the current technology for fugitive dust control. Different methods of fugitive dust control, including chemical, physical, and vegetative, have been used or tested on mill tailings piles. This report presents the results of a literature review and discussions with manufacturers and users of available stabilization materials and techniques.

Uranium-mill appraisal program

International Nuclear Information System (INIS)

Everett, R.J.; Cain, C.L.

1982-08-01

The results of special team appraisals at NRC-licensed uranium mills in the period May to November 1981 are reported. Since the Three Mile Island accident, NRC management has instituted a program of special team appraisals of radiation protection programs at certain NRC-licensed facilities. These appraisals were designed to identify weaknesses and strengths in NRC-licensed programs, including those areas not covered by explicit regulatory requirements. The regulatory requirements related to occupational radiation protection and environmental monitoring at uranium mills have been extensively upgraded in the past few years. In addition, there was some NRC staff concern with respect to the effectiveness of NRC licensing and inspection programs. In response to this concern and to changes in mill requirements, the NRC staff recommended that team appraisals be conducted at mills to determine the adequacy of mill programs, the effectiveness of the new requirements, and mill management implementation of programs and requirements. This report describes the appraisal scope and methodology as well as summary findings and conclusions. Significant weaknesses identified during the mill appraisals are discussed as well as recommendations for improvements in uranium mill programs and mill licensing and inspection

Predicting radon flux from uranium mill tailings

International Nuclear Information System (INIS)

Freeman, H.D.; Hartley, J.N.

1983-11-01

Pacific Northwest Laboratory (PNL), under contract to the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project (UMTRAP) office, is developing technology for the design of radon barriers for uranium mill tailings piles. To properly design a radon cover for a particular tailings pile, the radon flux emanating from the bare tailings must be known. The tailings characteristics required to calculate the radon flux include radium-226 content, emanating power, bulk density, and radon diffusivity. This paper presents theoretical and practical aspects of estimating the radon flux from an uranium tailings pile. Results of field measurements to verify the calculation methodology are also discussed. 24 references, 4 figures, 4 tables

Sustainability of uranium mining and milling: toward quantifying resources and eco-efficiency.

Science.gov (United States)

Mudd, Gavin M; Diesendorf, Mark

2008-04-01

The mining of uranium has long been a controversial public issue, and a renewed debate has emerged on the potential for nuclear power to help mitigate against climate change. The central thesis of pro-nuclear advocates is the lower carbon intensity of nuclear energy compared to fossil fuels, although there remains very little detailed analysis of the true carbon costs of nuclear energy. In this paper, we compile and analyze a range of data on uranium mining and milling, including uranium resources as well as sustainability metrics such as energy and water consumption and carbon emissions with respect to uranium production-arguably the first time for modern projects. The extent of economically recoverable uranium resources is clearly linked to exploration, technology, and economics but also inextricably to environmental costs such as energy/water/chemicals consumption, greenhouse gas emissions, and social issues. Overall, the data clearly show the sensitivity of sustainability assessments to the ore grade of the uranium deposit being mined and that significant gaps remain in complete sustainability reporting and accounting. This paper is a case study of the energy, water, and carbon costs of uranium mining and milling within the context of the nuclear energy chain.

Retrieving Storm Electric Fields From Aircraft Field Mill Data. Part I: Theory

Science.gov (United States)

Koshak, W. J.

2005-01-01

It is shown that the problem of retrieving storm electric fields from an aircraft instrumented with several electric field mill sensors can be expressed in terms of a standard Lagrange multiplier optimization problem. The method naturally removes aircraft charge from the retrieval process without having to use a high voltage stinger and linearly combined mill data values. It also allows a variety of user-supplied physical constraints (the so-called side constraints in the theory of Lagrange multipliers). Additionally, this paper introduces a novel way of performing the absolute calibration of an aircraft that has several benefits over conventional analyses. In the new approach, absolute calibration is completed by inspecting the time derivatives of mill and pitch data for a pitch down maneuver performed at high (greater than 1 km) altitude. In Part II of this study, the above methods are tested and then applied to complete a full calibration of a Citation aircraft.

Uranium Mill Tailings Radiation Control Act of 1978

International Nuclear Information System (INIS)

Magee, J.

1980-01-01

The long-term environmental effects of the Uranium Mill Tailings Radiation Control Act of 1978 address the public health hazards of radioactive wastes and recognize the significance of this issue to public acceptance of nuclear energy. Title I of the Act deals with stabilizing and controlling mill tailings at inactive sites and classifies the sites by priority. It represents a major Federal commitment. Title II changes and strengthens Nuclear Regulatory Commission authority, but it will have little overall impact. It is not possible to assess the Act's effect because there is no way to know if current technology will be adequate for the length of time required. 76 references

Scale-up of organic reactions in ball mills: process intensification with regard to energy efficiency and economy of scale.

Science.gov (United States)

Stolle, Achim; Schmidt, Robert; Jacob, Katharina

2014-01-01

The scale-up of the Knoevenagel-condensation between vanillin and barbituric acid carried out in planetary ball mills is investigated from an engineering perspective. Generally, the reaction proceeded in the solid state without intermediate melting and afforded selectively only one product. The reaction has been used as a model to analyze the influence and relationship of different parameters related to operation in planetary ball mills. From the viewpoint of technological parameters the milling ball diameter, dMB, the filling degree with respect to the milling balls' packing, ΦMB,packing, and the filling degree of the substrates with respect to the void volume of the milling balls' packing, ΦGS, have been investigated at different reaction scales. It was found that milling balls with small dMB lead to higher yields within shorter reaction time, treaction, or lower rotation frequency, rpm. Thus, the lower limit is set considering the technology which is available for the separation of the milling balls from the product after the reaction. Regarding ΦMB,packing, results indicate that the optimal value is roughly 50% of the total milling beakers' volume, VB,total, independent of the reaction scale or reaction conditions. Thus, 30% of VB,total are taken by the milling balls. Increase of the initial batch sizes changes ΦGS significantly. However, within the investigated parameter range no negative influence on the yield was observed. Up to 50% of VB,total can be taken over by the substrates in addition to 30% for the total milling ball volume. Scale-up factors of 15 and 11 were realized considering the amount of substrates and the reactor volume, respectively. Beside technological parameters, variables which influence the process itself, treaction and rpm, were investigated also. Variation of those allowed to fine-tune the reaction conditions in order to maximize the yield and minimize the energy intensity.

Integration of micro milling highspeed spindle on a microEDM-milling machine set-up

DEFF Research Database (Denmark)

De Grave, Arnaud; Hansen, Hans Nørgaard; Andolfatto, Loic

2009-01-01

In order to cope with repositioning errors and to combine the fast removal rate of micro milling with the precision and small feature size achievable with micro EDM milling, a hybrid micro-milling and micro-EDM milling centre was built and tested. The aim was to build an affordable set-up, easy...... by micro milling. Examples of test parts are shown and used as an experimental validation....

Biotechnological applications for the utilisation of wastes from palm oil mills

Energy Technology Data Exchange (ETDEWEB)

Cheah, S C; Ma, A N; Ooi, L C.L.; Ong, A S.H.

1988-05-01

The milling of oil palm fruits produces about two-and-a-half to three times as much effluent as oil does. It also generates a large amount of lignocellulosic wastes, mainly in the form of empty fruit bunches, press cake fibres and nut shell. Research efforts at PORIM have been directed towards the utilisation of these wastes as a means to solve the problem of environmental pollution as well as for the generation of economic returns for the mills. We have studied a thermophilic contact process for the anaerobic digestion of palm oil mill effluent and its potential for generating biogas for energy uses. Our work has also shown that the condensate derived from the fruit sterilisation process during milling is amenable to fermentation for the production of single cell protein (SCP) and exo-enzymes. The enzymes produced have been applied for oil clarification, oil recovery from press cake fibers and saccharification of the fibers for the production of sugar feedstocks. This paper will also introduce the concept of integrated waste management for the palm oil mill through the implementation of these technologies.

Real-time particle size analysis using focused beam reflectance measurement as a process analytical technology tool for a continuous granulation-drying-milling process.

Science.gov (United States)

Kumar, Vijay; Taylor, Michael K; Mehrotra, Amit; Stagner, William C

2013-06-01

Focused beam reflectance measurement (FBRM) was used as a process analytical technology tool to perform inline real-time particle size analysis of a proprietary granulation manufactured using a continuous twin-screw granulation-drying-milling process. A significant relationship between D20, D50, and D80 length-weighted chord length and sieve particle size was observed with a p value of 0.05).

Uranium Mill Tailings Management

International Nuclear Information System (INIS)

Nelson, J.D.

1982-01-01

This book presents the papers given at the Fifth Symposium on Uranium Mill Tailings Management. Advances made with regard to uranium mill tailings management, environmental effects, regulations, and reclamation are reviewed. Topics considered include tailings management and design (e.g., the Uranium Mill Tailings Remedial Action Project, environmental standards for uranium mill tailings disposal), surface stabilization (e.g., the long-term stability of tailings, long-term rock durability), radiological aspects (e.g. the radioactive composition of airborne particulates), contaminant migration (e.g., chemical transport beneath a uranium mill tailings pile, the interaction of acidic leachate with soils), radon control and covers (e.g., radon emanation characteristics, designing surface covers for inactive uranium mill tailings), and seepage and liners (e.g., hydrologic observations, liner requirements)

Preliminary Test of Upgraded Conventional Milling Machine into PC Based CNC Milling Machine

International Nuclear Information System (INIS)

Abdul Hafid

2008-01-01

CNC (Computerized Numerical Control) milling machine yields a challenge to make an innovation in the field of machining. With an action job is machining quality equivalent to CNC milling machine, the conventional milling machine ability was improved to be based on PC CNC milling machine. Mechanically and instrumentally change. As a control replacing was conducted by servo drive and proximity were used. Computer programme was constructed to give instruction into milling machine. The program structure of consists GUI model and ladder diagram. Program was put on programming systems called RTX software. The result of up-grade is computer programming and CNC instruction job. The result was beginning step and it will be continued in next time. With upgrading ability milling machine becomes user can be done safe and optimal from accident risk. By improving performance of milling machine, the user will be more working optimal and safely against accident risk. (author)

Unconstrained SU(2) and SU(3) Yang-Mills classical mechanics

International Nuclear Information System (INIS)

Dahmen, B.; Raabe, B.

1992-01-01

A systematic study of contraints in SU(2) and SU(3) Yang-Mills classical mechanics is performed. Expect for the SU(2) case with spatial angular momenta they turn out to be nonholonomic. The complete elimination of the unphysical gauge and rotatinal degrees of freedom is achieved using Dirac's constraint formalism. We present an effective unconstrained formulation of the general SU(2) Yang-Mills classical mechanics as well as for SU(3) in the subspace of vanishing spatial angular momenta that is well suited for further explicit dynamical investigations. (orig.)

Geothermal drilling and completion technology development program. Annual progress report, October 1979-September 1980

Energy Technology Data Exchange (ETDEWEB)

Varnado, S.G. (ed.)

1980-11-01

The progress, status, and results of ongoing research and development (R and D) within the Geothermal Drilling and Completion Technology Development Program are described. The program emphasizes the development of geothermal drilling hardware, drilling fluids, completion technology, and lost circulation control methods. Advanced drilling systems are also under development. The goals of the program are to develop the technology required to reduce well costs by 25% by 1983 and by 50% by 1987.

Study of the Utah uranium-milling industry. Volume I. A policy analysis

International Nuclear Information System (INIS)

Turley, R.E.

1980-05-01

This is the first volume of a two volume study of the Utah Uranium Milling Industry. The study was precipitated by a 1977 report issued by the Western Interstate Nuclear Board entitled Policy Recommendations on Financing Stabilization. Perpetual Surveillance and Maintenance of Uranium Mill Tailings. Volume I of this study is a policy analysis or technology assessment of the uranium milling industry in the state of Utah; specifically, the study addresses issues that deal with the perpetual surveillance, monitoring, and maintenance of uranium tailings piles at the end of uranium milling operations, i.e., following shutdown and decommissioning. Volume II of this report serves somewhat as an appendix. It represents a full description of the uranium industry in the state of Utah, including its history and statements regarding its future. The topics covered in volume I are as follows: today's uranium industry in Utah; management of the industry's characteristic nuclear radiation; uranium mill licensing and regulation; state licensing and regulation of uranium mills; forecast of future milling operations; policy needs relative to perpetual surveillance, monitoring, and maintenance of tailings; policy needs relative to perpetual oversight; economic aspects; state revenue from uranium; and summary with conclusions and recommendations. Appendices, figures and tables are also presented

VENVAL : a plywood mill cost accounting program

Science.gov (United States)

Henry Spelter

1991-01-01

This report documents a package of computer programs called VENVAL. These programs prepare plywood mill data for a linear programming (LP) model that, in turn, calculates the optimum mix of products to make, given a set of technologies and market prices. (The software to solve a linear program is not provided and must be obtained separately.) Linear programming finds...

Effects of Dry-Milling and Wet-Milling on Chemical, Physical and Gelatinization Properties of Rice Flour

Directory of Open Access Journals (Sweden)

Jitranut Leewatchararongjaroen

2016-09-01

Full Text Available Rice flour from nine varieties, subjected to dry- and wet-milling processes, was determined for its physical and chemical properties. The results revealed that milling method had an effect on properties of flour. Wet-milling process resulted in flour with significantly lower protein and ash contents and higher carbohydrate content. Wet-milled flour also tended to have lower lipid content and higher amylose content. In addition, wet-milled rice flour contained granules with smaller average size compared to dry-milled samples. Swelling power at 90 °C of wet-milled samples was higher while solubility was significantly lower than those of dry-milled flour. Dry milling process caused the destruction of the crystalline structure and yielded flour with lower crystallinity compared to wet-milling process, which resulted in significantly lower gelatinization enthalpy.

Maxillary arch rehabilitation using implant-supported computer-assisted design-computer-assisted manufacturing-milled titanium framework

Directory of Open Access Journals (Sweden)

Tulika S Khanna

2017-01-01

Full Text Available Esthetic and functional rehabilitation of completely edentulous maxillary arch with fixed implant supported prosthesis is a challenging task. Newer technologies such as computer assisted design computer assisted manufacturing (CAD CAM and cone beam conventional tomography play an important role in achieving predictable results. Full mouth porcelain fused to metal (PFM individual crowns on CAD CAM milled titanium framework provides positive esthetic and functional outcome. This is a case report of rehabilitation of partially edentulous maxillary arch patient. Staged rehabilitation of this patient was planned. In the first stage, root canal treatment of key abutment teeth was done, nonsalvageable teeth were removed, and immediate interim overdenture was provided. In the second stage, five Nobel Biocare dental implants were placed. After integration impressions were made, CAD CAM milled titanium bar was fabricated. Individual PFM crowns were made and cemented. This method gives better esthetic compared to acrylic fused to metal hybrid prosthesis with the advantage of retrievability just like screw retained prosthesis. Hence, this technique is good for rehabilitation of patients with high esthetic demands.

LIEKKI 2 - Combustion technology is environmental technology

Energy Technology Data Exchange (ETDEWEB)

Hupa, M. [Aabo Akademi, Turku (Finland)

1996-12-31

Finland has wide experience in applications of various combustion technologies and fuels and in supplying energy to industry and municipalities. Furthermore, combustion hardware and equipment are amongst our most important export products. Above all, fluidized bed boilers, recovery boilers for pulp mills and heavy diesel engines and diesel power plants have achieved excellent success in the world markets. Exports of these products alone have amounted to several billions of Finnish marks of annual sales in recent years. Within modern combustion technology, the objective is to control flue gas emissions as far as possible in the process itself, thus doing away with the need for the separate scrubbing of flue gases. To accomplish this it has been necessary to conduct a large amount of research on the details of the chemistry of combustion emissions and the flows in furnaces and engine cylinders. A host of completely new products are being developed for the combustion technology field. The LIEKKI programme has been particularly interested in so-called combined-cycle processes based on pressurized fluidized bed technology

Communication technologies to improve HPV vaccination initiation and completion: A systematic review.

Science.gov (United States)

Francis, Diane B; Cates, Joan R; Wagner, Kyla P Garrett; Zola, Tracey; Fitter, Jenny E; Coyne-Beasley, Tamera

2017-07-01

This systematic review examines the effectiveness of communication technology interventions on HPV vaccination initiation and completion. A comprehensive search strategy was used to identify existing randomized controlled trials testing the impact of computer-, mobile- or internet-based interventions on receipt of any dose of the HPV vaccine. Twelve relevant studies were identified with a total of 38,945 participants. The interventions were delivered using several different methods, including electronic health record (i.e. recall/reminder) prompts, text messaging, automated phone calls, interactive computer videos, and email. Vaccine initiation and completion was greater for technology-based studies relative to their control conditions. There is evidence that interventions utilizing communication technologies as their sole or primary mode for HPV vaccination intervention delivery may increase vaccination coverage. Communication technologies hold much promise for the future of HPV vaccination efforts, especially initiatives in practice-based settings. Copyright © 2017 Elsevier B.V. All rights reserved.

Investigation of the milling capabilities of the F10 Fine Grind mill using Box-Behnken designs.

Science.gov (United States)

Tan, Bernice Mei Jin; Tay, Justin Yong Soon; Wong, Poh Mun; Chan, Lai Wah; Heng, Paul Wan Sia

2015-01-01

Size reduction or milling of the active is often the first processing step in the design of a dosage form. The ability of a mill to convert coarse crystals into the target size and size distribution efficiently is highly desirable as the quality of the final pharmaceutical product after processing is often still dependent on the dimensional attributes of its component constituents. The F10 Fine Grind mill is a mechanical impact mill designed to produce unimodal mid-size particles by utilizing a single-pass two-stage size reduction process for fine grinding of raw materials needed in secondary processing. Box-Behnken designs were used to investigate the effects of various mill variables (impeller, blower and feeder speeds and screen aperture size) on the milling of coarse crystals. Response variables included the particle size parameters (D10, D50 and D90), span and milling rate. Milled particles in the size range of 5-200 μm, with D50 ranging from 15 to 60 μm, were produced. The impeller and feeder speeds were the most critical factors influencing the particle size and milling rate, respectively. Size distributions of milled particles were better described by their goodness-of-fit to a log-normal distribution (i.e. unimodality) rather than span. Milled particles with symmetrical unimodal distributions were obtained when the screen aperture size was close to the median diameter of coarse particles employed. The capacity for high throughput milling of particles to a mid-size range, which is intermediate between conventional mechanical impact mills and air jet mills, was demonstrated in the F10 mill. Prediction models from the Box-Behnken designs will aid in providing a better guide to the milling process and milled product characteristics. Copyright © 2014 Elsevier B.V. All rights reserved.

The U.S. regulatory framework for long-term management of uranium mill tailings

International Nuclear Information System (INIS)

Smythe, C.; Bierley, D.; Bradshaw, M.

1995-01-01

The US established the regulatory structure for the management, disposal, and long-term care of uranium mill tailings in 1978 with the passage of the Uranium Mill Tailings Radiation Control Act (UMTRCA) (Pub. L. 95-604). This legislation has governed the cleanup and disposal of uranium tailings at both inactive and active sites. The passage of the UMTRCA established a federal regulatory program for the cleanup and disposal of uranium mill tailings in the US. This program involves the DOE, the NRC, the EPA, various states and tribal governments, private licensees, and the general public. The DOE has completed surface remediation at 14 sites, with the remaining sites either under construction or in planning. The DOE's UMTRA Project has been very successful in dealing with public and agency demands, particularly regarding disposal site selection and transportation issues. The active sites are also being cleaned up, but at a slower pace than the inactive sites, with the first site tentatively scheduled for completion in 1996

Environmental impact of uranium mining and milling

International Nuclear Information System (INIS)

Dory, A.B.

1981-08-01

The author introduces the subject with an overview of the regulatory requirments and philosophy applied to uranium mines and mills. The special attention given to tailings management is highlighted, and a discussion of the basic environmental concerns is concluded with an itemizing of the main tasks facing the AECB. The extent of the environmental impact of uranium mining, milling and waste management is illustrated with specific details pertaining to mines in the Elliot Lake area. The author concludes that the impact on the ground and surface water system is not alarming, and the impact on air quality is not significant beyond a few hundred metres from the mining facilities. The publicly perceived impact is discussed, followed by a rationale for the continued licensing of new uranium mining operations complete with tailings management facilities

Comamonas sp. EB172 isolated from digester treating palm oil mill ...

African Journals Online (AJOL)

STORAGESEVER

2008-11-19

Nov 19, 2008 ... palm oil mill effluent as potential polyhydroxyalkanoate ... Technology, Faculty of Biotechnology and Biomolecular Sciences, Universiti Putra Malaysia, ... industry is actively looking for ways to minimize the ... methane gas.

Analysis of Ward identities in supersymmetric Yang-Mills theory

Science.gov (United States)

Ali, Sajid; Bergner, Georg; Gerber, Henning; Montvay, Istvan; Münster, Gernot; Piemonte, Stefano; Scior, Philipp

2018-05-01

In numerical investigations of supersymmetric Yang-Mills theory on a lattice, the supersymmetric Ward identities are valuable for finding the critical value of the hopping parameter and for examining the size of supersymmetry breaking by the lattice discretisation. In this article we present an improved method for the numerical analysis of supersymmetric Ward identities, which takes into account the correlations between the various observables involved. We present the first complete analysis of supersymmetric Ward identities in N=1 supersymmetric Yang-Mills theory with gauge group SU(3). The results indicate that lattice artefacts scale to zero as O(a^2) towards the continuum limit in agreement with theoretical expectations.

Einstein-Yang-Mills from pure Yang-Mills amplitudes

Energy Technology Data Exchange (ETDEWEB)

Nandan, Dhritiman; Plefka, Jan [Institut für Physik and IRIS Adlershof, Humboldt-Universität zu Berlin,Zum Großen Windkanal 6, D-12489 Berlin (Germany); Schlotterer, Oliver [Max-Planck-Institut für Gravitationsphysik, Albert-Einstein-Institut,Am Mühlenberg 1, D-14476 Potsdam (Germany); Wen, Congkao [I.N.F.N. Sezione di Roma Tor Vergata,Via della Ricerca Scientifica, 00133 Roma (Italy)

2016-10-14

We present new relations for scattering amplitudes of color ordered gluons and gravitons in Einstein-Yang-Mills theory. Tree-level amplitudes of arbitrary multiplicities and polarizations involving up to three gravitons and up to two color traces are reduced to partial amplitudes of pure Yang-Mills theory. In fact, the double-trace identities apply to Einstein-Yang-Mills extended by a dilaton and a B-field. Our results generalize recent work of Stieberger and Taylor for the single graviton case with a single color trace. As the derivation is made in the dimension-agnostic Cachazo-He-Yuan formalism, our results are valid for external bosons in any number of spacetime dimensions. Moreover, they generalize to the superamplitudes in theories with 16 supercharges.

7 CFR 868.310 - Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice...

Science.gov (United States)

2010-01-01

... Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice. (See also Â... Milled Rice Principles Governing Application of Standards § 868.310 Grades and grade requirements for the classes Long Grain Milled Rice, Medium Grain Milled Rice, Short Grain Milled Rice, and Mixed Milled Rice...

75 FR 71463 - Woodland Mills Corporation Mill Spring, NC; Notice of Revised Determination on Reconsideration

Science.gov (United States)

2010-11-23

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-73,695] Woodland Mills Corporation Mill Spring, NC; Notice of Revised Determination on Reconsideration By application dated July 22... regarding the eligibility of workers and former workers of Woodland Mills Corporation, Mill Spring, North...

Optimization of CNC end milling process parameters using PCA ...

African Journals Online (AJOL)

Optimization of CNC end milling process parameters using PCA-based Taguchi method. ... International Journal of Engineering, Science and Technology ... To meet the basic assumption of Taguchi method; in the present work, individual response correlations have been eliminated first by means of Principal Component ...

Uranium Mill Tailings Remedial Action Program. Annual status report

International Nuclear Information System (INIS)

1983-12-01

The FY 1983 project accomplishments are: completed the Remedial Action Plan and Phase I engineering design for the Canonsburg processing site; completed remedial action on an additional 52 vicinity properties and the inclusion of an additional 303 properties in the Uranium Mill Tailings Remedial Action Project; executed cooperative agreements with four states and the Navajo Nation; published the draft environmental impact statement for Salt Lake City site; and issued the approved Project Plan

Tailings technology. Decommissioning and rehabilitation remedial action technology development

International Nuclear Information System (INIS)

Ramsey, R.W. Jr.

1982-01-01

This paper is to provide an overview of technology requirements for long-term uranium mill tailings disposal and remedial actions for existing tailings to ensure their adequate disposal. The paper examines the scientific disciplines that are the basis for the technology of uranium mill tailings stabilization and the design of barriers to control radiological exposure or environmental degradation at the location of tailings disposal. The discussion is presented as a hypothetical course of instruction at a fictitious university. Features of six mechanisms of dispersal or intrusion are examined with brief discussion of the applicable technology development for each. The paper serves as an introduction to subsequent specific technology development papers in the session. (author)

Effects of Ultrasonics-Assisted Face Milling on Surface Integrity and Fatigue Life of Ni-Alloy 718

Science.gov (United States)

Suárez, Alfredo; Veiga, Fernando; de Lacalle, Luis N. López; Polvorosa, Roberto; Lutze, Steffen; Wretland, Anders

2016-11-01

This work investigates the effects of ultrasonic vibration-assisted milling on important aspects such us material surface integrity, tool wear, cutting forces and fatigue resistance. As an alternative to natural application of ultrasonic milling in brittle materials, in this study, ultrasonics have been applied to a difficult-to-cut material, Alloy 718, very common in high-temperature applications. Results show alterations in the sub-superficial part of the material which could influence fatigue resistance of the material, as it has been observed in a fatigue test campaign of specimens obtained with the application of ultrasonic milling in comparison with another batch obtained applying conventional milling. Tool wear pattern was found to be very similar for both milling technologies, concluding the study with the analysis of cutting forces, exhibiting certain improvement in case of the application of ultrasonic milling with a more stable evolution.

Unconstrained SU(2) and SU(3) Yang-Mills clasical mechanics

International Nuclear Information System (INIS)

Dahmen, B.; Raabe, B.

1992-01-01

A systematic study of constraints in SU(2) and SU(3) Yang-Mills classical mechanics is performed. Expect for the SU(2) case with vanishing spatial angular momenta they turn out to be non-holonomic. Using Dirac's constraint formalism we achieve a complete elimination of the unphysical gauge and rotational degrees of freedom. This leads to an effective unconstrained formulation both for the full SU(2) Yang-Mills classical mechanics and for the SU(3) case in the subspace of vanishing spatial angular momenta. We believe that our results are well suited for further explicit dynamical investigations. (orig.)

Research kinetic of motion of milling bodies in ball mill, outfit heat-exchange unit and calculation of its energy performance

Science.gov (United States)

Romanovich, A. A.; Romanovich, M. A.; Apukhtina, I. V.

2018-03-01

The article considers topical issues of energy saving in cement production with the use of a technological grinding complex, which includes a press roller grinder and a ball mill. Rational conditions of grinding are proposed for pre-shredded material through the installation of blade energy exchange devices (BEED) in the mill drum. The loading level in the first chamber varies periodically depending on the drum rotation angle, equipped with BEED. In the zone of BEED’s active action, there is a “scooping” of a part of grinding bodies together with crushed material, raising them to a height and giving them a longitudinally transverse movement, which is different from movement created in the mill without BEED. At the same time, additional work that consumes engine power is being done. A technique is proposed for calculating the additional engine power consumption of a mill, equipped with a BEED. This power is spent on creating a longitudinal-transverse motion of grinding bodies and its first and second chambers in areas of active influence of the BEED. Comparative analysis of results obtained experimentally and calculations of proposed equations show a high convergence of results. These analytical dependencies may be interest to Russian and foreign organizations that carry out their activities in the field of design and manufacture of cement equipment, as well as to cement producers.

Uranium-mill-tailings remedial-action project (UMTRAP) cover and liner technology development project

International Nuclear Information System (INIS)

Hartley, J.N.; Gee, G.W.; Freeman, H.D.; Cline, J.F.; Beedlow, P.A.; Buelt, J.L.; Relyea, J.R.; Tamura, T.

1982-01-01

Cover and liner systems for uranium mill tailings in the United States must satisfy stringent requirements regarding long-term stability, radon control, and radionuclide and hazardous chemical migration. The cover placed over a tailings pile serves three basic purposes: (1) to reduce the release of radon, (2) to prevent the intrusion of plant roots and burrowing animals into the tailings, and (3) to limit surface erosion. The liner placed under a tailings pile prevents the migration of radionuclides and hazardous chemicals to groundwater. Pacific Northwest Laboratory is developing and evaluating cover and liner systems that meet these objectives and conform to federal standards. The cover and liner technology discussed in this paper involves: (1) single and multilayer earthen cover systems, (2) asphalt emulsion radon barrier systems, (3) biobarrier systems, (4) revegetation and rock covers, and (5) asphalt, clay, and synthetic liner systems. These systems have been tested at the Grand Junction, Colorado, tailings pile, where they have been shown to effectively reduce radon releases and radionuclide and chemical migration

Getting nanometric MoO3 through chemical synthesis and high energy milling

International Nuclear Information System (INIS)

Santos-Beltrán, M.; Paraguay-Delgado, F.; Santos-Beltrán, A.; Fuentes, L.

2015-01-01

The effects of high energy mechanical milling (HEMM) were studied on the microstructure and optical properties of MoO 3 for hexagonal and orthorhombic phases. Employing HEMM was possible change particle size as a function of mechanical milling time, as well as the small quantity transformation percentage from hexagonal to orthorhombic phase. The relationship between microstrain and optical properties generated was studied. The electronic structures were calculated using the Density Functional Theory (DFT); to determinate partial density of state (PDOS). Band gap structure calculations show a good correlation between experimental and simulated data. The approximated values of microstrain, particle size, lattice parameters and oxygen vacancies were obtained employing the Rietveld refinement of X-ray diffraction patterns. Samples were characterized by electron microscopy techniques, surface area analysis (BET), thermal-gravimetric analysis (TGA), differential scanning calorimetry (DSC) and ultraviolet–visible spectroscopy (UV–Vis). It was possible, obtain particles with size below 40 nm by 30 min milling. - Graphical abstract: Orthorhombic phase, SEM image, SAED before milling, milling NPs, Particle size and band gap variation by milling time. - Highlights: • MoO 3 with hexagonal and orthorhombic structures was synthesized selectively. • By milling short time (30 m), it was possible get 40 nm diameter particles. • The band gap decrease for nanoparticles, then corroborated by simulation. • MoO 3 nanoparticles get high surface area for new technologic applications

Depreciation of bearing blocks of rollers of roller conveyers of rolling mills

Science.gov (United States)

Artiukh, Viktor; Belyaev, Michael; Ignatovich, Igor; Miloradova, Nadezda

2017-10-01

Essential increase in functional durability of a node of a roller of the roller conveyer of the rolling mill by the rational choice of parameters of the small-size shock-absorber (buffer adapter) is shown. At the same time dimensions of a node don’t change, costs of reconstruction are small. The possibility of management of loadings in a bearing node without change of technology parameters of the process which is carried out by the rolling mill is confirmed.

Evaluation of End Mill Coatings

Energy Technology Data Exchange (ETDEWEB)

L. J. Lazarus; R. L. Hester,

2005-08-01

Milling tests were run on families of High Speed Steel (HSS) end mills to determine their lives while machining 304 Stainless Steel. The end mills tested were made from M7, M42 and T15-CPM High Speed Steels. The end mills were also evaluated with no coatings as well as with Titanium Nitride (TiN) and Titanium Carbo-Nitride (TiCN) coatings to determine which combination of HSS and coating provided the highest increase in end mill life while increasing the cost of the tool the least. We found end mill made from M42 gave us the largest increase in tool life with the least increase in cost. The results of this study will be used by Cutting Tool Engineering in determining which end mill descriptions will be dropped from our tool catalog.

Bioassay for uranium mill tailings

International Nuclear Information System (INIS)

Tschaeche, A.N.

1986-01-01

Uranium mill tailings are composed of fine sand that contains, among other things, some uranium (U/sup 238/ primarily), and all of the uranium daughters starting with /sup 230/Th that are left behind after the usable uranium is removed in the milling process. Millions of pounds of tailings are and continue to be generated at uranium mills around the United States. Discrete uranium mill tailings piles exist near the mills. In addition, the tailings materials were used in communities situated near mill sites for such purposes as building materials, foundations for buildings, pipe runs, sand boxes, gardens, etc. The Uranium Mill Tailings Remedial Action Project (UMTRAP) is a U.S. Department of Energy Program designed with the intention of removing or stabilizing the mill tailings piles and the tailings used to communities so that individuals are not exposed above the EPA limits established for such tailings materials. This paper discusses the bioassay programs that are established for workers who remove tailings from the communities in which they are placed

Biomass torrefaction mill

Science.gov (United States)

Sprouse, Kenneth M.

2016-05-17

A biomass torrefaction system includes a mill which receives a raw biomass feedstock and operates at temperatures above 400 F (204 C) to generate a dusty flue gas which contains a milled biomass product.

Overview of milling techniques for improving the solubility of poorly water-soluble drugs

Directory of Open Access Journals (Sweden)

Zhi Hui Loh

2015-07-01

Full Text Available Milling involves the application of mechanical energy to physically break down coarse particles to finer ones and is regarded as a “top–down” approach in the production of fine particles. Fine drug particulates are especially desired in formulations designed for parenteral, respiratory and transdermal use. Most drugs after crystallization may have to be comminuted and this physical transformation is required to various extents, often to enhance processability or solubility especially for drugs with limited aqueous solubility. The mechanisms by which milling enhances drug dissolution and solubility include alterations in the size, specific surface area and shape of the drug particles as well as milling-induced amorphization and/or structural disordering of the drug crystal (mechanochemical activation. Technology advancements in milling now enable the production of drug micro- and nano-particles on a commercial scale with relative ease. This review will provide a background on milling followed by the introduction of common milling techniques employed for the micronization and nanonization of drugs. Salient information contained in the cited examples are further extracted and summarized for ease of reference by researchers keen on employing these techniques for drug solubility and bioavailability enhancement.

Oxidant reduction and biodegradability improvement of paper mill effluent by irradiation

International Nuclear Information System (INIS)

Tiezheng Wang; Waite, T.D.; Kurucz, C.

1994-01-01

Paper mill bleach processing wastewaters represent a large input of hazardous compounds to the environment and these compounds are usually non-biodegradable. A preliminary study using a 5000 Ci 60 Co gamma radiation source as a surrogate for electron beam irradiation, potentially an emerging technology for wastewater treatment, to treat a paper mill bleach effluent showed that for an absorbed dose of 800 krads, chemical oxygen demand (COD) was reduced by 13.5% and 5 day biochemical oxygen demand (BOD 5 ) was increased 58.6%. These changes altered the value of COD/BOD 5 from 14 to 5. For the same dose, the absorbable organic halogen (AOX) was reduced 76.2%. These results suggested the possibility of using the electron beam process to detoxify paper mill effluent thereby generating a more biodegradable wastewater. (author)

Surface Generation Modeling in Ball Nose End Milling: a review of relevant literature

DEFF Research Database (Denmark)

Bissacco, Giuliano

One of the most common metal removal operation used in industry is the milling process. This machining process is well known since the beginning of last century and has experienced, along the years, many improvements of the basic technology, as concerns tools, machine tools, coolants...... to be adjusted afterwards. Nevertheless, many efforts have been done during the last 50 years in order to realize prediction tools for machining processes and particularly for conventional turning and milling operations. Most of these models aim at prediction of cutting forces tool wear and tool life. However...... been addressed in this direction. Among all the machining operations, ball nose end milling has shown great potentials, particularly in machining of sculptured surfaces with high requirements in terms of surface finish; this is due to the good spatial agreement of the mill shape with the geometry...

Engineering Study for a Full Scale Demonstration of Steam Reforming Black Liquor Gasification at Georgia-Pacific's Mill in Big Island, Virginia; FINAL

International Nuclear Information System (INIS)

Robert De Carrera; Mike Ohl

2002-01-01

Georgia-Pacific Corporation performed an engineering study to determine the feasibility of installing a full-scale demonstration project of steam reforming black liquor chemical recovery at Georgia-Pacific's mill in Big Island, Virginia. The technology considered was the Pulse Enhanced Steam Reforming technology that was developed and patented by Manufacturing and Technology Conversion, International (MTCI) and is currently licensed to StoneChem, Inc., for use in North America. Pilot studies of steam reforming have been carried out on a 25-ton per day reformer at Inland Container's Ontario, California mill and on a 50-ton per day unit at Weyerhaeuser's New Bern, North Carolina mill

Process optimization and particle engineering of micronized drug powders via milling.

Science.gov (United States)

Brunaugh, A; Smyth, H D C

2017-11-13

Process control and optimization is a critical aspect of process analytical technology (PAT), quality by design (QbD), and the implementation of continuous manufacturing procedures. While process control and optimization techniques have been utilized in other manufacturing industries for decades, the pharmaceutical industry has only recently begun to adopt these procedures. Micronization, particularly milling, is a generally low-yield, high-energy consumption process that is well suited for a process optimization mindset. This review discusses optimization of the pharmaceutical milling process through design space development, theoretical and empirical modeling, and monitoring of critical quality attributes.

Self-Improving CNC Milling Machine

OpenAIRE

Spilling, Torjus

2014-01-01

This thesis is a study of the ability of a CNC milling machine to create parts for itself, and an evaluation of whether or not the machine is able to improve itself by creating new machine parts. This will be explored by using off-the-shelf parts to build an initial machine, using 3D printing/rapid prototyping to create any special parts needed for the initial build. After an initial working machine is completed, the design of the machine parts will be adjusted so that the machine can start p...

Microstructure and properties of copper composite containing in situ NbC reinforcement: Effects of milling speed

International Nuclear Information System (INIS)

Zuhailawati, Hussain; Salihin, Hassin Mohd; Mahani, Yusoff

2010-01-01

This paper presents a study on the effects of milling speed on the properties of in situ copper-based composite produced by mechanical alloying followed by cold pressing and sintering. A powdered mixture of copper, niobium and graphite with the composition of Cu-30%NbC was milled at various speeds (100, 200, 300 and 400 rpm). The NbC phase started to precipitate in the as-milled powder after 30 h milling at 400 rpm and the formation was completed after sintering at 950 o C. Enhancements of NbC phase formation with a reduction in Cu crystallite size were observed with the increase of milling speed. Density, hardness and electrical conductivity of the sintered composite were evaluated. An increase in milling speed resulted in an increase in sintered density and hardness but a reduction of electrical conductivity. The changes in the properties were correlated to the formation of NbC phase and refinement of copper and niobium carbide crystallite size since higher milling speed is associated with higher kinetic energy per hit.

On the Recent Use of Membrane Technology for Olive Mill Wastewater Purification

Directory of Open Access Journals (Sweden)

Javier Miguel Ochando-Pulido

2015-09-01

Full Text Available Many reclamation treatments as well as integrated processes for the purification of olive mill wastewaters (OMW have already been proposed and developed but not led to completely satisfactory results, principally due to complexity or cost-ineffectiveness. The olive oil industry in its current status, composed of little and dispersed factories, cannot stand such high costs. Moreover, these treatments are not able to abate the high concentration of dissolved inorganic matter present in these highly polluted effluents. In the present work, a review on the actual state of the art concerning the treatment and disposal of OMW by membranes is addressed, comprising microfiltration (MF, ultrafiltration (UF, nanofiltration (NF, and reverse osmosis (RO, as well as membrane bioreactors (MBR and non-conventional membrane processes such as vacuum distillation (VD, osmotic distillation (OD and forward osmosis (FO. Membrane processes are becoming extensively used to replace many conventional processes in the purification of water and groundwater as well as in the reclamation of wastewater streams of very diverse sources, such as those generated by agro-industrial activities. Moreover, a brief insight into inhibition and control of fouling by properly-tailored pretreatment processes upstream the membrane operation and the use of the critical and threshold flux theories is provided.

Procedure of uranium mine and mill facilities decommissioning work

International Nuclear Information System (INIS)

Li Renjie

1995-01-01

The procedure of decommissioning work of uranium mine and mill facilities includes three stages: preparation, on-the-spot construction and acceptance after being completed. The first stage, preparation, is discussed in detail, and it is presented to take the measures of strengthening leadership and improving leading body to conduct the decommissioning work best

Effect of milling duration on the evolution of shape memory properties in a powder processed Cu-Al-Ni-Ti alloy

Energy Technology Data Exchange (ETDEWEB)

Sharma, Mohit; Gupta, Gaurav K.; Shafeeq, Muhamed M.; Modi, Om P.; Prasad, Braj K. [CSIR - Advanced Materials and Processes Research Institute, Bhopal (India)

2013-09-15

The present work describes the effect of milling duration on the properties of a powder metallurgy processed Cu-Al-Ni-Ti shape memory alloy employing mechanical alloying. Powder mixtures milled for different durations were sintered in order to investigate the formation of solid solution and evolution of martensitic structure. The idea was to optimize the duration of milling (mechanical alloying) to obtain chemical homogeneity as well as shape memory properties in the processed material without undergoing extensive post homogenization treatment. The martensitic structure was noted to evolve in the powder mix milled for at least 16 hrs, whereas complete transformation to martensite occurred after milling for 40 hrs. Interestingly, the dissolution of alloying elements (to form the {beta} phase prior to the formation of martensite) was noted to complete partially only during mechanical alloying for 40 hrs and remaining during subsequent sintering for 1 hr. The hot pressed compacts of the powders milled for 40 hrs were chemically homogeneous and consisted of fully martensite phase, which is essential for the realization of shape memory properties. They also revealed almost 100% shape recovery at the applied pre-strain levels of 1 and 2%. (orig.)

Phytoremediation Potential of Vetiver System Technology for Improving the Quality of Palm Oil Mill Effluent

Directory of Open Access Journals (Sweden)

Negisa Darajeh

2014-01-01

Full Text Available Palm oil mill effluent (POME, a pollutant produced by the palm oil industry, was treated by the Vetiver system technology (VST. This technology was applied for the first time to treat POME in order to decrease biochemical oxygen demand (BOD and chemical oxygen demand (COD. In this study, two different concentrations of POME (low and high were treated with Vetiver plants for 2 weeks. The results showed that Vetiver was able to reduce the BOD up to 90% in low concentration POME and 60% in high concentration POME, while control sets (without plant only was able to reduce 15% of BOD. The COD reduction was 94% in low concentration POME and 39% in high concentration POME, while control just shows reduction of 12%. Morphologically, maximum root and shoot lengths were 70 cm, the number of tillers and leaves was 344 and 86, and biomass production was 4.1 kg m−2. These results showed that VST was effective in reducing BOD and COD in POME. The treatment in low concentration was superior to the high concentration. Furthermore, biomass of plant can be considered as a promising raw material for biofuel production while high amount of biomass was generated in low concentration of POME.

Decontamination effect of milling by a jet mill on bacteria in rice flour.

Science.gov (United States)

Sotome, Itaru; Nei, Daisuke; Tsuda, Masuko; Mohammed, Sharif Hossen; Takenaka, Makiko; Okadome, Hiroshi; Isobe, Seiichiro

2011-06-01

The decontamination effect of milling by a jet mill was investigated by counting the number of bacteria in brown and white rice flour with mean particle diameters of 3, 20, and 40µm prepared by the jet mill. In the jet mill, the particles are crushed and reduced in size by the mechanical impact caused by their collision. Although the brown and white rice grains were contaminated with approximately 10(6) and 10(5) CFU/g bacteria, the microbial load of the rice flour decreased as the mean particle diameter decreased, ultimately decreasing to approximately 104 and 103 CFU/g in the brown and white rice flour. The temperature and pressure changes of the sample were not considered to have an effect on reducing the bacterial count during the milling. Hence, it was thought that the rice flour was decontaminated by other effects.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

OpenAIRE

Garc?a Nieto, Paulino Jos?; Garc?a-Gonzalo, Esperanza; Ord??ez Gal?n, Celestino; Bernardo S?nchez, Antonio

2016-01-01

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism i...

Impacts of new environmental and safety regulations on uranium mining, milling and waste management in China

International Nuclear Information System (INIS)

Wang Yongping; Zheng Yuhui; Shi Xiangjun

2001-01-01

Nuclear power progress has triggered the development and innovation of nuclear fuel industries in China. At present the Chinese government has put more emphasis on industrial readjustment and technical innovation in uranium mining and milling in order to fuel the nuclear power development, satisfy environmental protection and improve economic efficiency of the industry. The current organizations and approval procedure for establishing regulations and the implementation and consequences of the regulations, technical polices and development strategies concerning uranium mining, milling, treatment of waste ores and mill tailings, and reduction of the workers' suffered exposure dose etc. in China are discussed and the economic, health and environmental impacts of the uranium mining and metallurgy with reformation achievement and the introduction of advanced technologies such as the in-situ leaching and heap leaching mining technologies are assessed in this paper. (author)

1981 radon barrier field test at Grand Junction uranium mill tailings pile

International Nuclear Information System (INIS)

Hartley, J.N.; Gee, G.W.; Baker, E.G.; Freeman, H.D.

1983-04-01

Technologies to reduce radon released from uranium mill tailings are being investigated by Pacific Northwest Laboratory as part of the Department of Energy's Uranium Mill Tailings Remedial Action Project (UMTRAP) Technology development program. These technologies include: (1) earthen cover systems, (2) multilayer cover systems, and (3) asphalt emulsion radon barrier systems. During the summer of 1981, a field test was initiated at the Grand Junction, Colorado, uranium tailings pile to evaluate and compare the effectiveness of each radon barrier system. Test plots cover about 1.2 ha (3 acres). The field test has demonstrated the effectiveness of all three cover systems in reducing radon release to near background levels ( 2 s - 1 ). In conjunction with the field tests, column tests (1.8 m diameter) were initiated with cover systems similar to those in the larger field test plots. The column tests allow a direct comparison of the two test procedures and also provide detailed information on radon transport

Bio-refinery system of DME or CH4 production from black liquor gasification in pulp mills

Energy Technology Data Exchange (ETDEWEB)

Raza, M.; Jinyue Yan (Dept. of Chemical Engineering and Technology/Energy Processes, Royal Institute of Technology, Stockholm (Sweden)). e-mail: rnaqvi@kth.se; Froeling, Morgan (Dept. of Chemical and Biological Engineering, Chalmers Univ. of Technology, Goeteborg (Sweden))

2009-07-01

The consumption of fossil fuels is rapidly increasing and there is an urgent need to develop technologies for renewable fuel production not only as alternatives but also as additional fuels. Efficient polygeneration of transportation fuels with heat and electricity is one of the innovative technologies which have potential to replace fossil fuels and mitigate climate change. Two potential technologies of producing dimethyl ether (DME) and methane (CH4) as alternative fuels integrated with black liquor gasification have been studied and compared in this paper. System performance is evaluated based on: (i) Comparison with the reference pulp mill, (ii) Fuel to product efficiency (FTPE) and (iii) Biofuel Production Potential (BPP). The comparison with the reference mill shows that black liquor to biofuel route will add a highly significant new revenue stream to the pulp industry. The results indicate a large potential of DME and CH4 production globally in terms of black liquor availability. BPP and FTPE of CH4 production is higher than DME due to more optimized integration with the pulping process and elimination of evaporation unit in the pulp mill

Uranium mill tailings management

International Nuclear Information System (INIS)

1982-01-01

Facilities for the disposal of uranium mill tailings will invariably be subjected to geomorphological and climatological influences in the long-term. Proceedings of a workshop discuss how the principles of geomorphology can be applied to the siting, design, construction, decommissioning and rehabilitation of disposal facilities in order to provide for long-term containment and stability of tailings. The characteristics of tailings and their behaviour after disposal influence the potential impacts which might occur in the long-term. Proceedings of another workshop examine the technologies for uranium ore processing and tailings conditioning with a view to identifying improvements that could be made in such characteristics

Loop groups and Yang-Mills theory in dimension two

DEFF Research Database (Denmark)

Gravesen, Jens

1990-01-01

Given a connection ω in a G-bundle over S2, then a process called radial trivialization from the poles gives a unique clutching function, i.e., an element γ of the loop group ΩG. Up to gauge equivalence, ω is completely determined by γ and a map f:S2 →g into the Lie algebra. Moreover, the Yang......-Mills function of ω is the sum of the energy of γ and the square of a certain norm of f. In particular, the Yang-Mills functional has the same Morse theory as the energy functional on ΩG. There is a similar description of connections in a G-bundle over an arbitrary Riemann surface, but so far not of the Yang...

Screening of plant species as ground cover on uranium mill tailings

International Nuclear Information System (INIS)

Venu Babu, P.; Eapen, S.

2012-01-01

The concept of construction of dams or holding areas for uranium mill tailings is relatively new in India and to date there is only one such facility being maintained by Uranium Corporation of India Limited (UCIL) at Jaduguda in Jharkhand. Due to the residual nature of radionuclides, chiefly uranium and its daughter products, special emphasis is given to the engineering aspects of the mill tailings ponds so as to ensure safety to general public for at least 200 years. Once a mill tailings pond reaches to its full capacity, creation of barrier layers over the mill tailings to prevent seepage of rain water and also erosion of mill tailings due to wind and water are advocated and a number of procedures are followed worldwide. Taking the extraordinary period of public safety to be assured, providing soil covers along with contouring and appropriate slopes over which vegetation is grown is gaining popularity. The vegetation not only reduces the impact of rain water hitting the soil cover, thereby reducing the soil erosion, but also lowers the moisture in the soil cover by extensive evapotranspiration, ensuring long term hydrological separation of the mill tailings underneath. Based on set criteria, applicable to the field scenario of mill tailings, a screening experiment was conducted under pot culture conditions to evaluate the survival and growth of different plant species. The plants after germination and hardening were transplanted into beakers containing mill tailings and periodical measurements on appropriate morphological characteristics such as plant height, length of twiners, number of tillers and number of leaves were recorded and evaluated. Of the twenty species tested in mill tailings, significant differences were noticed in the vigour of growth and several plant species could indeed establish well completing their life cycle including flowering and seed setting. Further, several leguminous species could also produce root nodules. It appears that the

Reducing water consumption in the paper mill; Paperitehtaan vedenkaeytoen vaehentaeminen (WACI) - EKY 02

Energy Technology Data Exchange (ETDEWEB)

Pekuri, T.; Pekkanen, A. [UPM-Kymmene Oyj, Valkeakoski (Finland)

1998-12-31

This WACI-project was divided into several subprojects, which were started with gathering of present knowledge and entering to laboratory and pilot tests. In some projects there were mill scale trials in water connections and internal purification systems. In the `Quality Demands of Water` subproject the process waters used in the printing paper machines of UPM-Kymmene were surveyed. Lab tests were made for the different applications like shower, washing, seal and dilution of internally purified circulation waters. In `Mechanical Pulp Washing` project the target was to study how the different water connections around the TMP washing press will affect the paper machine runnability. It was also started to develop separating technique for TMP fibre extractive. `Micro and Electroflotation` studies have been made mainly on pilot scale but also in new mill-scale unit. `Membrane Technology` research consisted of both lab, pilot and mill scale studies, where different membrane qualities with different process waters have been tested. `Evaporation` trials were made on pilot scale for different process waters and condensates and concentrates were analysed. Condensates were tested for different applications. The possibility to `Reuse Waste Water` concentrated mainly on how to remove the brown colour. `Simulations` were done to find out what will be the new dcs balance in different wet end processes after new water connections including so-called kidneys. In the `Paper Quality` subproject the effects of dcs on bonding ability of TMP fibres were studied on lab scale with artificial pitch component and also with circulation concentrates. This 2.5 year Tekes-project was completed at the end of April 1998. (orig.)

Reducing water consumption in the paper mill; Paperitehtaan vedenkaeytoen vaehentaeminen (WACI) - EKY 02

Energy Technology Data Exchange (ETDEWEB)

Pekuri, T; Pekkanen, A [UPM-Kymmene Oyj, Valkeakoski (Finland)

1999-12-31

This WACI-project was divided into several subprojects, which were started with gathering of present knowledge and entering to laboratory and pilot tests. In some projects there were mill scale trials in water connections and internal purification systems. In the `Quality Demands of Water` subproject the process waters used in the printing paper machines of UPM-Kymmene were surveyed. Lab tests were made for the different applications like shower, washing, seal and dilution of internally purified circulation waters. In `Mechanical Pulp Washing` project the target was to study how the different water connections around the TMP washing press will affect the paper machine runnability. It was also started to develop separating technique for TMP fibre extractive. `Micro and Electroflotation` studies have been made mainly on pilot scale but also in new mill-scale unit. `Membrane Technology` research consisted of both lab, pilot and mill scale studies, where different membrane qualities with different process waters have been tested. `Evaporation` trials were made on pilot scale for different process waters and condensates and concentrates were analysed. Condensates were tested for different applications. The possibility to `Reuse Waste Water` concentrated mainly on how to remove the brown colour. `Simulations` were done to find out what will be the new dcs balance in different wet end processes after new water connections including so-called kidneys. In the `Paper Quality` subproject the effects of dcs on bonding ability of TMP fibres were studied on lab scale with artificial pitch component and also with circulation concentrates. This 2.5 year Tekes-project was completed at the end of April 1998. (orig.)

Improving Energy Efficiency Via Optimized Charge Motion and Slurry Flow in Plant Scale Sag Mills

Energy Technology Data Exchange (ETDEWEB)

Raj K. Rajamani

2006-07-21

A research team from the University of Utah is working to make inroads into saving energy in these SAG mills. In 2003, Industries of the Future Program of the Department of Energy tasked the University of Utah team to build a partnership between the University and the mining industry for the specific purpose of reducing energy consumption in SAG mills. A partnership was formed with Cortez Gold Mines, Outokumpu Technology, Kennecott Utah Copper Corporation, and Process Engineering Resources Inc. At Cortez Gold Operations the shell and pulp lifters of the semiautogenous grinding mill was redesigned. The redesigned shell lifter has been in operation for over three years and the redesigned pulp lifter has been in operation for over nine months now. This report summarizes the dramatic reductions in energy consumption. Even though the energy reductions are very large, it is safe to say that a 20% minimum reduction would be achieved in any future installations of this technology.

Airborne effluent control at uranium mills

International Nuclear Information System (INIS)

Sears, M.B.

1976-01-01

The Oak Ridge National Laboratory has made an engineering cost--environmental benefit study of radioactive waste treatment systems for decreasing the amount of radioactive materials released from uranium ore processing mills. This paper summarizes the results of the study which pertain to the control and/or abatement of airborne radioactive materials from the mill processes. The tailings area is not included. Present practices in the uranium milling industry, with particular emphasis on effluent control and waste management, have been surveyed. A questionnaire was distributed to each active mill in the United States. Replies were received from about 75 percent of the mill operators. Visits were made to six operating uranium mills that were selected because they represented the different processes in use today and the newest, most modern in mill designs. Discussions were held with members of the Region IV Office of NRC and the Grand Junction Office of ERDA. Nuclear Science Abstracts, as well as other sources, were searched for literature pertinent to uranium mill processes, effluent control, and waste management

FM Interviews: Stephanie Mills

OpenAIRE

Valauskas, Edward

2002-01-01

Stephanie Mills is an author, editor, lecturer and ecological activist who has concerned herself with the fate of the earth and humanity since 1969, when her commencement address at Mills College in Oakland, Calif., drew the attention of a nation. Her speech, which the New York Times called "perhaps the most anguished statement" of the year's crop of valedictory speeches, predicted a bleak future. According to Mills, humanity was destined for suicide, the result of overpopulation and overuse ...

Disposal of olive mill wastewater with DC arc plasma method.

Science.gov (United States)

Ibrahimoglu, Beycan; Yilmazoglu, M Zeki

2018-07-01

Olive mill wastewater is an industrial waste, generated as a byproduct of olive oil production process and generally contains components such as organic matter, suspended solids, oil, and grease. Although various methods have been developed to achieve the disposal of this industrial wastewater, due to the low cost, the most common disposal application is the passive storage in the lagoons. The main objective of this study is to reduce pollution parameters in olive mill wastewater and draw water to discharge limits by using plasma technology. Plasma-assisted disposal of olive mill wastewater method could be an alternative disposal technique when considering potential utilization of treated water in agricultural areas and economic value of flammable plasma gas which is the byproduct of disposal process. According to the experimental results, the rates of COD (chemical oxygen demand) and BOD (biological oxygen demand) of olive mill wastewater are decreased by 94.42% and 95.37%, respectively. The dissolved oxygen amount is increased from 0.36 to 6.97 mg/l. In addition, plasma gas with high H 2 content and treated water that can be used in agricultural areas for irrigation are obtained from non-dischargeable wastewater. Copyright © 2018 Elsevier Ltd. All rights reserved.

Rough mill simulator version 3.0: an analysis tool for refining rough mill operations

Science.gov (United States)

Edward Thomas; Joel Weiss

2006-01-01

ROMI-3 is a rough mill computer simulation package designed to be used by both rip-first and chop-first rough mill operators and researchers. ROMI-3 allows users to model and examine the complex relationships among cutting bill, lumber grade mix, processing options, and their impact on rough mill yield and efficiency. Integrated into the ROMI-3 software is a new least-...

Prevention, Minimization and Control of Environmental Pollution at Mexico Sugar Mill

Directory of Open Access Journals (Sweden)

Dominguez-Manjarrez Candi Ashanti

2014-10-01

Full Text Available This research paper aims to recommend control measures directed towards preventing and minimizing pollution, looking forward to the improvement of the environmental management on the sugar industry in Mexico. This issue has been put on hold due to the necessity to address the economic, social and technological issues affecting it over time. In order to better understand the productive process and the actual problem that the industry is facing, while proposing effective and possible actions for improvement, a sugar mill type was selected as a case of study. A comprehensive assessment of the production process for the standard sugar was made, considering the activities in the field and at the mill. The proposed measures in the sugar mill allowed savings in consumption of ground water average 3,620 cubic meters per day, during the period of study, reduction in solid waste generated average 325 kilograms per day by implementing a waste separation program, and reducing atmospheric emissions of particles acting as fuel for a boiler operated with bagasse. The prevention, minimization and pollution control measures proposed can be applied to other mills in the country with the appropriate adaptations.

Containment systems for uranium-mill tailings

International Nuclear Information System (INIS)

Hartley, J.N.; Buelt, J.L.

1982-11-01

Cover and liner systems for uranium mill tailings in the United States must satisfy stringent requirements regarding long-term stability, radon control, and radionuclide and hazardous chemical migration. The cover and liner technology discussed in this paper involves: (1) single and multilayer earthen cover systems; (2) asphalt emulsion radon barrier systems; and (3) asphalt, clay, and synthetic liner systems. These systems have been field tested at the Grand Junction, Colorado, tailings pile, where they have been shown to effectively reduce radon releases and radionuclide and chemical migration

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data.

Science.gov (United States)

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-28

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC-MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc . Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC-MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

Directory of Open Access Journals (Sweden)

Paulino José García Nieto

2016-01-01

Full Text Available Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC in combination with multivariate adaptive regression splines (MARS technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC–MARS-based model was successfully used here to predict the milling tool flank wear (output variable as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC–MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed.

Hybrid ABC Optimized MARS-Based Modeling of the Milling Tool Wear from Milling Run Experimental Data

Science.gov (United States)

García Nieto, Paulino José; García-Gonzalo, Esperanza; Ordóñez Galán, Celestino; Bernardo Sánchez, Antonio

2016-01-01

Milling cutters are important cutting tools used in milling machines to perform milling operations, which are prone to wear and subsequent failure. In this paper, a practical new hybrid model to predict the milling tool wear in a regular cut, as well as entry cut and exit cut, of a milling tool is proposed. The model was based on the optimization tool termed artificial bee colony (ABC) in combination with multivariate adaptive regression splines (MARS) technique. This optimization mechanism involved the parameter setting in the MARS training procedure, which significantly influences the regression accuracy. Therefore, an ABC–MARS-based model was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. Regression with optimal hyperparameters was performed and a determination coefficient of 0.94 was obtained. The ABC–MARS-based model's goodness of fit to experimental data confirmed the good performance of this model. This new model also allowed us to ascertain the most influential parameters on the milling tool flank wear with a view to proposing milling machine's improvements. Finally, conclusions of this study are exposed. PMID:28787882

Effect of milling time on microstructure and properties of Nano-titanium polymer by high-energy ball milling

Science.gov (United States)

Wang, Bo; Wei, Shicheng; Wang, Yujiang; Liang, Yi; Guo, Lei; Xue, Junfeng; Pan, Fusheng; Tang, Aitao; Chen, Xianhua; Xu, Binshi

2018-03-01

Nano-titanium (Nano-Ti) was prepared by high-energy ball milling from pure Ti power and grinding agents (Epoxy resin) at room temperature. The effect of milling time on structure and properties of Nano-Ti polymer were investigated systematically. The results show that high-energy ball milling is an effective way to produce Nano-Ti polymer. The dispersion stability and compatibility between Ti power and grinding agents are improved by prolonging the milling time at a certain degree, that is to say, the optimization milling time is 240 min. The particle size of Ti powder and the diffraction peaks intensity of Ti decrease obviously as the milling time increases due to the compression stress, shear friction and other mechanical forces are formed during ball milling. FT-IR result displays that the wavenumber of all the bands move to lower wavenumber after ball milling, and the epoxy ring is open. The system internal energy rises owing to the broken epoxy group and much more Nano-Ti is formed to promote the grafting reaction between Nano-Ti and epoxy resin. The results from TEM and XPS also prove that. And the grafting ration is maximum as the milling time is 240 min, the mass loss ratio is 17.53%.

Focused ion beam milling of carbon fibres

International Nuclear Information System (INIS)

Huson, Mickey G.; Church, Jeffrey S.; Hillbrick, Linda K.; Woodhead, Andrea L.; Sridhar, Manoj; Van De Meene, Allison M.L.

2015-01-01

A focused ion beam has been used to mill both individual carbon fibres as well as fibres in an epoxy composite, with a view to preparing flat surfaces for nano-indentation. The milled surfaces have been assessed for damage using scanning probe microscopy nano-indentation and Raman micro-probe analysis, revealing that FIB milling damages the carbon fibre surface and covers surrounding areas with debris of disordered carbon. The debris is detected as far as 100 μm from the milling site. The energy of milling as well as the orientation of the beam was varied and shown to have an effect when assessed by Raman spectroscopy. - Highlights: • Focused ion beam (FIB) milling was used to mill flat surfaces on carbon fibres. • Raman spectroscopy showed amorphous carbon was generated during FIB milling. • The amorphous debris is detected as far as 100 μm from the milling site. • This surface degradation was confirmed by nano-indentation experiments.

DOE/Fossil Energy`s drilling, completion, and stimulation RD&D: A technologies/products overview

Energy Technology Data Exchange (ETDEWEB)

Duda, J.R.; Yost, A.B. II

1995-12-31

An overview of natural gas drilling, completion, and stimulation RD&D sponsored by the US Department of Energy is reported in this paper. Development of high rate-of-penetration drilling systems and underbalanced drilling technologies are detailed among other RD&D activities. The overview serves as a technology transfer medium and is intended to accelerate the deployment of the products and technologies described.

Architecture and environmental restoration: Remediating uranium mill tailings from buildings

International Nuclear Information System (INIS)

Teply, J.D.

1991-01-01

The US Department of Energy (DOE) Grand Junction Projects Office (GJPO) manages the Uranium Mill Tailings Remedial Action (UMTRA) Program in Grand Junction, Colorado. This program is a congressionally mandated clean up of by-product waste that resulted from the extraction of yellow cake from uranium ore. The by-product waste, a fine sand commonly called open-quotes mill tailingclose quotes is contaminated with low-level radioactivity. These mill tailings were available to the community for use as construction material from approximately 1952 to 1966; their use as bedding material for concrete slabs, utilities, backfill materials, concrete sand, and mortar created unique remediation problems that required innovative solutions. This paper describes how design personnel approach the remediation of structures, the evaluation of the buildings, and the factors that must be considered in completing the remediation design. This paper will not address the health risks of the tailings in an inhabited space, the remediation of exterior areas, or the process of determining where the tailings exist in the building

Annual status report on the Uranium Mill Tailings Remedial Action Program

International Nuclear Information System (INIS)

1992-12-01

This fourteenth annual status report for the Uranium Mill Tailings Remedial Action (UMTRA) Project Office summarizes activities of the Uranium Mill Tailings Remedial Action Surface (UMTRA-Surface) and Uranium Mill Tailings Remedial Action Groundwater (UMTRA-Groundwater) Projects undertaken during fiscal year (FY) 1992 by the US Department of Energy (DOE) and other agencies. Project goals for FY 1993 are also presented. An annual report of this type was a statutory requirement through January 1, 1986, pursuant to the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law (PL) 95-604. The DOE will continue to submit annual reports to DOE-Headquarters, the states, tribes, and local representatives through Project completion in order to inform the public of the yearly Project status. The purpose of the remedial action is to stabilize and control the tailings and other residual radioactive material (RRM) located on the inactive uranium processing sites in a safe and environmentally sound manner, and to minimize or eliminate potential health hazards. Commercial and residential properties near designated processing sites that are contaminated with material from the sites, herein referred to as ''vicinity properties (VP),'' are also eligible for remedial action. Included in the UMTRA Project are 24 inactive uranium processing sites and associated VPs located in 10 states, and the VPs associated with the Edgemont, South Dakota, uranium mill currently owned by the Tennessee Valley Authority (TVA) (Figure A.1, Appendix A)

Key technologies for well drilling and completion in ultra-deep sour gas reservoirs, Yuanba Gasfield, Sichuan Basin

Directory of Open Access Journals (Sweden)

Jiaxiang Xia

2016-12-01

Full Text Available The Yuanba Gasfield is a large gas field discovered by Sinopec in the Sichuan Basin in recent years, and another main exploration area for natural gas reserves and production increase after the Puguang Gasfield. The ultra-deep sour gas reservoir in the Yuanba Gasfield is characterized by complicated geologic structure, deep reservoirs and complex drilled formation, especially in the continental deep strata which are highly abrasive with low ROP (rate of penetration and long drilling period. After many years of drilling practice and technical research, the following six key drilling and completion technologies for this type reservoir are established by introducing new tools and technologies, developing specialized drill bits and optimizing drilling design. They are: casing program optimization technology for ROP increasing and safe well completion; gas drilling technology for shallow continental strata and high-efficiency drilling technology for deep high-abrasion continental strata; drilling fluid support technologies of gas–liquid conversion, ultra-deep highly-deviated wells and horizontal-well lubrication and drag reduction, hole stability control and sour gas contamination prevention; well cementing technologies for gas medium, deep-well long cementing intervals and ultra-high pressure small space; horizontal-well trajectory control technologies for measuring instrument, downhole motor optimization and bottom hole assembly design; and liner completion modes and completion string optimization technologies suitable for this gas reservoir. Field application shows that these key technologies are contributive to ROP increase and efficiency improvement of 7000 m deep horizontal wells and to significant operational cycle shortening.

Surface Quality of Staggered PCD End Mill in Milling of Carbon Fiber Reinforced Plastics

Directory of Open Access Journals (Sweden)

Guangjun Liu

2017-02-01

Full Text Available Machined surface quality determines the reliability, wear resistance and service life of carbon fiber reinforced plastic (CFRP workpieces. In this work, the formation mechanism of the surface topography and the machining defects of CFRPs are proposed, and the influence of milling parameters and fiber cutting angles on the surface quality of CFRPs is obtained, which can provide a reference for extended tool life and good surface quality. Trimming and slot milling tests of unidirectional CFRP laminates are performed. The surface roughness of the machined surface is measured, and the influence of milling parameters on the surface roughness is analyzed. A regression model for the surface roughness of CFRP milling is established. A significance test of the regression model is conducted. The machined surface topography of milling CFRP unidirectional laminates with different fiber orientations is analyzed, and the effect of fiber cutting angle on the surface topography of the machined surface is presented by using a digital super depth-of-field microscope and scanning electron microscope (SEM. To study the influence of fiber cutting angle on machining defects, the machined topography under different fiber orientations is analyzed. The slot milling defects and their formation mechanism under different fiber cutting angles are investigated.

Yang-Mills gravity in biconformal space

International Nuclear Information System (INIS)

Anderson, Lara B; Wheeler, James T

2007-01-01

We write a gravity theory with Yang-Mills-type action using the biconformal gauging of the conformal group. We show that the resulting biconformal Yang-Mills gravity theories describe 4-dim, scale-invariant general relativity in the case of slowly changing fields. In addition, we systematically extend arbitrary 4-dim Yang-Mills theories to biconformal space, providing a new arena for studying flat-space Yang-Mills theories. By applying the biconformal extension to a 4-dim pure Yang-Mills theory with conformal symmetry, we establish a 1-1, onto mapping between a set of gravitational gauge theories and 4-dim, flat-space gauge theories

Equations of motion for the new D=10 N=1 supergravity-Yang-Mills theory

International Nuclear Information System (INIS)

Vashakidze, Sh.I.

1988-01-01

An on-shell superfield formulation of the dual (type IB) ten-dimensional N=1 supergravity coupled to Yang-Mills theory is presented. The coupling is completely specified in superspace by A-tensor supercurrent which, at the same time, takes into account all superstring corrections in the slope parameter expansion. The complete set of equations of motion is derived

Operations improvement of the recycling water-cooling systems of sugar mills

Directory of Open Access Journals (Sweden)

Shcherbakov Vladimir Ivanovich

Full Text Available Water management in sugar factories doesn’t have analogues in its complexity among food industry enterprises. Water intensity of sugar production is very high. Circulation water, condensed water, pulp press water and others are used in technological processes. Water plays the main role in physical, chemical, thermotechnical processes of beet processing and sugar production. As a consequence of accession of Russia to the WTO the technical requirements for production processes are changing. The enforcements of ecological services to balance scheme of water consumption and water disposal increased. The reduction of fresh water expenditure is one of the main tasks in economy of sugar industry. The substantial role in fresh water expenditure is played by efficiency of cooling and aeration processes of conditionally clean waters of the 1st category. The article contains an observation of the technologies of the available solutions and recommendations for improving and upgrading the existing recycling water-cooling systems of sugar mills. The authors present the block diagram of the water sector of a sugar mill and a method of calculating the optimal constructive and technological parameters of cooling devices. Water cooling towers enhanced design and upgrades are offered.

Influence of rice sample preparation and milling procedures on milling quality appraisals

Science.gov (United States)

The objective of this research was to investigate the effect of sample preparation and milling procedure on milling quality appraisals of rough rice. Samples of freshly harvested medium-grain rice (M202) with different initial moisture contents (MCs) ranging from 20.2% to 25.1% (w.b.) were used for...

Influence of milling process on efavirenz solubility

Directory of Open Access Journals (Sweden)

Erizal Zaini

2017-01-01

Full Text Available Introduction: The aim of this study was to investigate the influence of the milling process on the solubility of efavirenz. Materials and Methods: Milling process was done using Nanomilling for 30, 60, and 180 min. Intact and milled efavirenz were characterized by powder X-ray diffraction, scanning electron microscopy (SEM, spectroscopy infrared (IR, differential scanning calorimetry (DSC, and solubility test. Results: The X-ray diffractogram showed a decline on peak intensity of milled efavirenz compared to intact efavirenz. The SEM graph depicted the change from crystalline to amorphous habit after milling process. The IR spectrum showed there was no difference between intact and milled efavirenz. Thermal analysis which performed by DSC showed a reduction on endothermic peak after milling process which related to decreasing of crystallinity. Solubility test of intact and milled efavirenz was conducted in distilled water free CO2with 0.25% sodium lauryl sulfate media and measured using high-performance liquid chromatography method with acetonitrile: distilled water (80:20 as mobile phases. The solubility was significantly increased (P < 0.05 after milling processes, which the intact efavirenz was 27.12 ± 2.05, while the milled efavirenz for 30, 60, and 180 min were 75.53 ± 1.59, 82.34 ± 1.23, and 104.75 ± 0.96 μg/mL, respectively. Conclusions: Based on the results, the solubility of efavirenz improved after milling process.

Yang-Mills-Chern-Simons supergravity

International Nuclear Information System (INIS)

Lue, H; Pope, C N; Sezgin, E

2004-01-01

N = (1, 0) supergravity in six dimensions admits AdS 3 x S 3 as a vacuum solution. We extend our recent results presented in Lue et al (2002 Preprint hep-th/0212323), by obtaining the complete N = 4 Yang-Mills-Chern-Simons supergravity in D = 3, up to quartic fermion terms, by S 3 group manifold reduction of the six-dimensional theory. The SU(2) gauge fields have Yang-Mills kinetic terms as well as topological Chern-Simons mass terms. There is in addition a triplet of matter vectors. After diagonalization, these fields describe two triplets of topologically-massive vector fields of opposite helicities. The model also contains six scalars, described by a GL(3, R)/SO(3) sigma model. It provides the first example of a three-dimensional gauged supergravity that can be obtained by a consistent reduction of string theory or M-theory and that admits AdS 3 as a vacuum solution. There are unusual features in the reduction from six-dimensional supergravity, owing to the self-duality condition on the 3-form field. The structure of the full equations of motion in N = (1, 0) supergravity in D = 6 is also elucidated, and the role of the self-dual field strength as torsion is exhibited

Uranium mill tailings conditioning technology

International Nuclear Information System (INIS)

Dreesen, D.R.; Cokal, E.J.; Wangen, L.E.; Williams, J.M.; O'Brien, P.D.; Thode, E.F.

1982-01-01

Conditioning of uranium mill tailings involves the physicochemical alteration of tailings to remove or immobilize mobile radionuclides and toxic trace elements before disposal in a repository. The principal immobilization approach under investigation is sintering tailings at high temperatures (1100-1200 deg. C) to radically alter the structure of tailings. This thermal stabilization at 1200 deg. C reduced radon emanation power for tailings sands by factors of 20 to 200 and for tailings fines by factors of 300 to 1100. Substantial reductions in the leachability of most contaminants have been found for thermally conditioned tailings. Obvious mineral transformations occur, including an increase in amorphous material, the conversion of gypsum to anhydrite and its subsequent decomposition, the disappearance of clay minerals, and some decrease in quartz content. A conceptual thermal stabilization process has been developed wherein obsolete coal-fired rotary cement kilns perform the sintering. An economic analysis of this conceptual process has shown that thermal stabilization can be competitive at certain tailings sites with other remedial actions requiring the excavation, transportation, and burial of tailings in a repository. An analysis of the long-term radiological hazard posed by untreated tailings and by tailings conditioned by radionuclide removal has illustrated the necessity of extracting both 226 Ra and 230 Th to achieve long-term hazard reductions. Sulphuric acid extraction of residual mineral values and important radionuclides from tailings has been investigated. Concentrated H 2 SO 4 can extract up to 80% of the 226 Ra, 70% of the Ba, and 90% of the 230 Th from tailings in a single stage extraction. An economic analysis of a sulphuric acid leach process was made to determine whether the value of minerals recovered from tailings would offset the leaching cost. For one relatively mineral-rich tailings pile, the U and V values would more than pay for the

Assessment of the best available wastewater management techniques for a textile mill: cost and benefit analysis.

Science.gov (United States)

Dogan, Bugce; Kerestecioglu, Merih; Yetis, Ulku

2010-01-01

In the present study, several water recovery and end-of-pipe wastewater treatment alternatives were evaluated towards the evaluation of Best Available Techniques (BATs) for the management of wastewaters from a denim textile mill in accordance with the European Union's Integrated Pollution Prevention and Control (IPPC) Directive. For this purpose, an assessment that translates the key environmental aspects into a quantitative measure of environmental performance and also financial analysis was performed for each of the alternatives. The alternatives considered for water recovery from dyeing wastewaters were nanofiltration (NF) with coagulation and/or microfiltration (MF) pre-treatment, ozonation or peroxone and Fenton oxidation. On the other hand, for the end-of-pipe treatment of the mill's mixed wastewater, ozonation, Fenton oxidation, membrane bioreactor (MBR) and activated sludge (AS) process followed by membrane filtration technologies were evaluated. The results have indicated that membrane filtration process with the least environmental impacts is the BAT for water recovery. On the other side, MBR technology has appeared as the BAT for the end-of-pipe treatment of the mill's mixed wastewater. A technical and financial comparison of these two BAT alternatives revealed that water recovery via membrane filtration from dyeing wastewaters is selected as the BAT for the water and wastewater management in the mill.

Tool Wear Analysis on Five-Axis Flank Milling for Curved Shape Part – Full Flute and Ground Shank End Mill

Directory of Open Access Journals (Sweden)

Syahrul Azwan Sundi

2017-01-01

Full Text Available This paper is a study on full flute (extra-long tool and ground shank end mill wear analysis by utilizing five-axis CNC to implement flank milling strategy on curved shape part. Five-axis machining eases the user to implement variations of strategy such as flank milling. Flank milling is different from point milling. Point milling cuts materials by using the tip of the tool whereas the flank milling uses the cutting tool body to cut material. The type of cutting tool used was end mill 10 mm diameter with High Speed Steel (HSS material. One factor at a time was utilized to analyze the overall data. Feed rate and spindle speed were the two main factors that been set up equally for both full flute and ground shank end mill. At the end of this research, the qualitative analysis based on tool wear between full flute and ground shank end mill is observed. Generally, both types of cutting tools showed almost the same failure indication such as broken edge or chipped off edge, formation of pinned hole on the surface and serration formation or built-up edge (BUE on the primary flute. However, the results obtained from the enlarged images which were captured by Optical Microscope indicated that, the ground shank end mill is better than the full flute end mill.

Particle deformation during stirred media milling

Science.gov (United States)

Hamey, Rhye Garrett

Production of high aspect ratio metal flakes is an important part of the paint and coating industry. The United States Army also uses high aspect ratio metal flakes of a specific dimension in obscurant clouds to attenuate infrared radiation. The most common method for their production is by milling a metal powder. Ductile metal particles are initially flattened in the process increasing the aspect ratio. As the process continues, coldwelding of metal flakes can take place increasing the particle size and decreasing the aspect ratio. Extended milling times may also result in fracture leading to a further decrease in the particle size and aspect ratio. Both the coldwelding of the particles and the breakage of the particles are ultimately detrimental to the materials performance. This study utilized characterization techniques, such as, light scattering and image analysis to determine the change in particle size as a function of milling time and parameters. This study proved that a fundamental relationship between the milling parameters and particle deformation could be established by using Hertz's theory to calculate the stress acting on the aluminum particles. The study also demonstrated a method by which milling efficiency could be calculated, based on the amount of energy required to cause particle deformation. The study found that the particle deformation process could be an energy efficient process at short milling times with milling efficiency as high as 80%. Finally, statistical design of experiment was used to obtain a model that related particle deformation to milling parameters, such as, rotation rate and milling media size.

Learning Activity Packets for Milling Machines. Unit I--Introduction to Milling Machines.

Science.gov (United States)

Oklahoma State Board of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

This learning activity packet (LAP) outlines the study activities and performance tasks covered in a related curriculum guide on milling machines. The course of study in this LAP is intended to help students learn to identify parts and attachments of vertical and horizontal milling machines, identify work-holding devices, state safety rules, and…

Application of controlled release technology to uranium mill tailings stabilization

International Nuclear Information System (INIS)

Burton, F.G.; Cataldo, D.A.; Cline, J.F.; Skiens, W.E.

1981-01-01

A trifluralin (herbicide) releasing device was developed with a theoretical effective lifetime in excess of 100 years. When placed in a layer in soil, the PCD system will prevent root penetration through that layer without harming the overlying vegetation. Equilibrium concentrations of trifluralin in soil can be adjusted (along with the theoretical life of the device) to suit specific needs. The present system was designed specifically to protect the asphalt layer or clay/aggregate barriers on uranium mill tailings piles; PCD devices composed of pellets could also be implanted over burial sites for radioactive and/or toxic materials, preventing translocation of those materials to plant shoots, and thence into the biosphere

STUDIES ON SELECTED PROPERTIES OF SURFACE LAYER OF C45 STEEL OBJECTS AFTER LASER CUTTING AND MILLING

Directory of Open Access Journals (Sweden)

Kazimierz Zaleski

2014-09-01

Full Text Available The article presents the results of studying the effects of technological parameters of milling upon surface roughness and microhardness of C45 steel objects after laser cutting. The metallographic structure formed as an effect of cutting by laser was also analyzed. The milling was performed on a FV-580a vertical machining centre. Depth of cut and feed per tooth were changed within the following range: ap = 0.09–0.18 mm and fz = 0.02–0.17 mm/tooth. To measure the surface roughness a Surtronic 3+ profile graphometer was used, whereas microhardness was measured with the use of a Leco LM 700AT microhardness tester. The surface roughness was significantly improved as a result of milling. The laser beam input and output zones were eliminated. Only a part of the layer hardened by laser cutting was removed while milling, in effect of which after milling the hardness of surface layer is much higher than hardness of the core.

Formation of metacinnabar by milling of liquid mercury and elemental sulfur for long term mercury storage

International Nuclear Information System (INIS)

Lopez, F.A.; Lopez-Delgado, A.; Padilla, I.; Tayibi, H.; Alguacil, F.J.

2010-01-01

In this paper we present the results of the formation of black HgS (metacinnabar) from liquid mercury and elemental sulfur using the mechanical energy provided by a ball mill in different conditions. Metacinnabar formation was observed even after short milling times (15 min) and unreacted liquid mercury was no longer detected after 60 min of milling. The reaction mechanism was monitored with a scanning electron microscope. The impact and friction forces of milling on the Hg and S mixture resulted in the formation of metacinnabar by reducing the size of mercury drops, giving rise to microspheres, and lowering the surface tension to allow sulfur grains to become adhered at the reaction interface. After 60 min of milling, the metacinnabar formation reaction was observed to be more than 99.99% complete, yielding a Toxicity Characteristic Leaching Procedure value of 3.1 μg/L Hg. The reaction product thus complies with the limits of the most stringent Universal Treatment Standard requirements, which allow a maximum TCLP concentration of 25 μg/L.

Nanocrystalline TiAl powders synthesized by high-energy ball milling: effects of milling parameters on yield and contamination

International Nuclear Information System (INIS)

Bhattacharya, Prajina; Bellon, Pascal; Averback, Robert S.; Hales, Stephen J.

2004-01-01

High-energy ball milling was employed to produce nanocrystalline Ti-Al powders. As sticking of the powders can be sufficiently severe to result in a near zero yield, emphasis was placed on varying milling conditions so as to increase the yield, while avoiding contamination of the powders. The effects of milling parameters such as milling tools, initial state of the powders and addition of process control agents (PCA's) were investigated. Cyclohexane, stearic acid and titanium hydride were used as PCA's. Milling was conducted either in a Cr-steel vial with C-steel balls, or in a tungsten carbide (WC) vial with WC balls, using either elemental or pre-alloyed powders. Powder samples were characterized using X-ray diffraction, scanning and transmission electron microscopy. In the absence of PCA's mechanical alloying in a WC vial and attrition milling in a Cr-steel vial were shown to lead to satisfactory yields, about 65-80%, without inducing any significant contamination of the powders. The results suggest that sticking of the powders on to the milling tools is correlated with the phase evolution occurring in these powders during milling

IMPACT OF DEPTH OF CUT ON CHIP FORMATION IN AZ91HP MAGNESIUM ALLOY MILLING WITH TOOLS OF VARYING CUTTING EDGE GEOMETRY

Directory of Open Access Journals (Sweden)

Olga Gziut

2015-05-01

Full Text Available Safety of Mg milling processes can be expressed by means of the form and the number of fractions of chips formed during milling. This paper presents the state of the art of magnesium alloys milling technology in the aspect of chip fragmentation. Furthermore, the impact of the depth of cut ap and the rake angle γ on the number of chip fractions was analysed in the study. These were conducted on AZ91HP magnesium cast alloy and milling was performed with carbide tools of varying rake angle values (γ = 5º and γ = 30º. It was observed that less intense chip fragmentation occurs with decreasing depth of cut ap. The number of chip fractions was lower at the tool rake angle of γ = 30º. The test results were formulated as technological recommendations according to the number of generated chip fractions.

Retrieving Storm Electric Fields from Aircraft Field Mill Data. Part 1; Theory

Science.gov (United States)

Koshak, W. J.

2006-01-01

It is shown that the problem of retrieving storm electric fields from an aircraft instrumented with several electric field mill sensors can be expressed in terms of a standard Lagrange multiplier optimization problem. The method naturally removes aircraft charge from the retrieval process without having to use a high voltage stinger and linearly combined mill data values. It allows a variety of user-supplied physical constraints (the so-called side constraints in the theory of Lagrange multipliers) and also helps improve absolute calibration. Additionally, this paper introduces an alternate way of performing the absolute calibration of an aircraft that has some benefits over conventional analyses. It is accomplished by using the time derivatives of mill and pitch data for a pitch down maneuver performed at high (greater than 1 km) altitude. In Part II of this study, the above methods are tested and then applied to complete a full calibration of a Citation aircraft.

The progress in the researches for uranium mill tailings cleaning treatment and no-waste uranium ore milling processes

International Nuclear Information System (INIS)

Wang Jintang

1990-01-01

The production of uranium mill tailings and their risk assessment are described. The moethods of uranium mill tailings disposal and management are criticized and the necessity of the researches for uranium mill tailings cleaning treatment and no-wasle uranium ore milling process are demonstrated. The progress for these researches in China and other countries with uranium production is reviewed, and the corresponding conclusions are reported

Microstructural Evolution, Thermodynamics, and Kinetics of Mo-Tm2O3 Powder Mixtures during Ball Milling

Directory of Open Access Journals (Sweden)

Yong Luo

2016-10-01

Full Text Available The microstructural evolution, thermodynamics, and kinetics of Mo (21 wt % Tm2O3 powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm2O3 to be decomposed and then dissolved into Mo crystal. After 96 h of ball milling, Tm2O3 was dissolved completely and the supersaturated nanocrystalline solid solution of Mo (Tm, O was obtained. The Mo lattice parameter increased with increasing ball-milling time, opposite for the Mo grain size. The size and lattice parameter of Mo grains was about 8 nm and 0.31564 nm after 96 h of ball milling, respectively. Ball milling induced the elements of Mo, Tm, and O to be distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo (21 wt % Tm2O3, it was mechanical work, not the negative heat of mixing, which provided the driving force to form a supersaturated nanocrystalline Mo (Tm, O solid solution.

75 FR 49524 - Woodland Mills Corporation, Mill Spring, NC; Notice of Affirmative Determination Regarding...

Science.gov (United States)

2010-08-13

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-73,695] Woodland Mills Corporation, Mill Spring, NC; Notice of Affirmative Determination Regarding Application for Reconsideration By application dated July 22, 2010, petitioners requested administrative [[Page 49525

Preliminary Study on Non-Fatal Occupational Injury among Operational Workers in Malaysia Palm Oil Mill

Directory of Open Access Journals (Sweden)

Ruslan Rumaizah

2017-01-01

Full Text Available Non-fatal occupational injury had becoming major global concern and its consequences to safety and health would be heavily burdening. The aim of this preliminary study was to investigate the distribution of non-fatal occupational injury among specific group of workers in palm oil mill and to acknowledge potential factors of injury causation. A questionnaire survey was designed to assess injury involvement during the employment period among operational workers of palm oil mill located in Southern Peninsular Malaysia. Thirty three (n= 33 workers volunteered and completed the questionnaire. Prevalence of injury among palm oil mill workers was 39.4% with sprain and burn were the common types of injury reported. Press Plant workers reported to have high cases of injuries. Majority of workers (78.8% stated noise was the main hazard in the palm oil mill, followed by heat hazard. Press Plant was identified as one of the specific risk group in palm oil mill based on the rate of injury occurrences reported by the workers. Exposure to noise hazard was estimated to be one of the potential factors of injury causation and further study should be made to measure the risk of hazard.

Safe management of wastes from the mining and milling of uranium and thorium ores

International Nuclear Information System (INIS)

1987-01-01

Wastes from the mining and milling of uranium and thorium ores pose potential environmental and public health problems because of their radioactivity and chemical composition. This document consists of two parts: a Code of Practice (Part I) and a Guide to the Code (Part II). The Code sets forth the requirements for the safe and responsible handling of the wastes resulting from the mining and milling of uranium and thorium ores, while the Guide presents further guidance in the use of the Code together with some discussion of the technology and concepts involved

Student Engagement and Completion in Precalculus Precalculus Mega Section: Efficiently Assisting Student Engagement and Completion with Communications and Information Technology

Science.gov (United States)

Brusi, Rima; Portnoy, Arturo; Toro, Nilsa

2013-01-01

The Precalculus Mega Section project was developed with the main purpose of improving the overall performance of the student body in Precalculus, an important gatekeeper course that affects student engagement and completion, with typical drop/failure rates of over 50 percent. Strategies such as integration of technology and additional practice…

Tool wear in terms of vibration effects in milling medium-density fibreboard with an industrial robot

International Nuclear Information System (INIS)

Tratar, Janez; Pusavec, Franci; Kopac, Janez

2014-01-01

Machining with robots represents a promising, highly flexible and cost effective alternative to standard machining and hand labour applications when machining mid tolerance soft material end products. One of the most challenging issues is to know the vibration characteristics in milling with the robots which greatly affect tool life. In general the technological bases of tool life expectancy while milling with robot arms are not available or studied. That's why the purpose of this paper is to investigate the influence of attained vibrations analysis during the milling process and correlated tool wear. Primarily the study is focused on tool wear according to the distance between the milling position and the robot's base. Results show that increasing distance between the robot's base and the milling position significantly affects tool wear because of the attained vibrations in proportion to the increasing distance respectively. Tool wear has also proved to be greater in comparison to machining with CNC machine and applicable new information for woodworking industry.

Preparation of 50Ni-45Ti-5Zr powders by high-energy ball milling and hot pressing

Energy Technology Data Exchange (ETDEWEB)

Marinzeck de Alcantara Abdala, Julia, E-mail: juabdala@yahoo.com.b [Instituto de Pesquisa e Desenvolvimento, Universidade do Vale do Paraiba, Av. Shishima Hifumi, 2911, 12244-000 Sao Jose dos Campos (Brazil); Bacci Fernandes, Bruno, E-mail: brunobacci@yahoo.com.b [Divisao de Engenharia Mecanica, Instituto Tecnologico de Aeronautica, Praca Marechal-do-Ar Eduardo Gomes, 50, 12228-904 Sao Jose dos Campos (Brazil); Santos, Dalcy Roberto dos, E-mail: dalcy@iae.cta.b [Instituto de Aeronautica e Espaco, Centro Tecnologico Aeroespacial, Praca Marechal-do-Ar Eduardo Gomes, 50, 12228-904 Sao Jose dos Campos (Brazil); Rodrigues Henriques, Vinicius Andre, E-mail: vinicius@iae.cta.b [Instituto de Aeronautica e Espaco, Centro Tecnologico Aeroespacial, Praca Marechal-do-Ar Eduardo Gomes, 50, 12228-904 Sao Jose dos Campos (Brazil); Moura Neto, Carlos de, E-mail: mneto@ita.b [Divisao de Engenharia Mecanica, Instituto Tecnologico de Aeronautica, Praca Marechal-do-Ar Eduardo Gomes, 50, 12228-904 Sao Jose dos Campos (Brazil); Saraiva Ramos, Alfeu, E-mail: alfeu@univap.b [Instituto de Pesquisa e Desenvolvimento, Universidade do Vale do Paraiba, Av. Shishima Hifumi, 2911, 12244-000 Sao Jose dos Campos (Brazil)

2010-04-16

This study reports on the preparation of the 50Ni-45Ti-5Zr (at.%) alloy by high-energy ball milling and hot pressing. The elemental powder mixture was processed in silicon nitride and hardened steel vials, and samples were collected after different milling times. To recover the previous powders in addition wet milling isopropyl alcohol (for 20 min) was adopted. The mechanically alloyed powders were hot-pressed under vacuum at 900 {sup o}C for 1 h using pressure levels close to 200 MPa. The milled powders were characterized by means of scanning electron microscopy, X-ray diffraction, and energy dispersive spectrometry techniques. It was noted that the ductile starting powders were continuously cold-welded during ball milling. This fact was more pronounced during the processing of 50Ni-45Ti-5Zr powders in hardened steel vial. After milling for 5 h, the results suggested that amorphous and nanocrystalline structures were achieved. The complete consolidation was found after hot pressing of mechanically alloyed 50Ni-45Ti-5Zr powders, and a large amount of the B2-NiTi phase was formed mainly after processing in stainless steel balls and vial.

Simulation of ball motion and energy transfer in a planetary ball mill

International Nuclear Information System (INIS)

Lu Sheng-Yong; Mao Qiong-Jing; Li Xiao-Dong; Yan Jian-Hua; Peng Zheng

2012-01-01

A kinetic model is proposed for simulating the trajectory of a single milling ball in a planetary ball mill, and a model is also proposed for simulating the local energy transfer during the ball milling process under no-slip conditions. Based on the kinematics of ball motion, the collision frequency and power are described, and the normal impact forces and effective power are derived from analyses of collision geometry. The Hertzian impact theory is applied to formulate these models after having established some relationships among the geometric, dynamic, and thermophysical parameters. Simulation is carried out based on two models, and the effects of the rotation velocity of the planetary disk Ω and the vial-to-disk speed ratio ω/Ω on other kinetic parameters is investigated. As a result, the optimal ratio ω/Ω to obtain high impact energy in the standard operating condition at Ω = 800 rpm is estimated, and is equal to 1.15. (interdisciplinary physics and related areas of science and technology)

Improving mine-mill water network design by reducing water and energy requirements

Energy Technology Data Exchange (ETDEWEB)

Gunson, A.J.; Klein, B.; Veiga, M. [British Columbia Univ., Vancouver, BC (Canada). Norman B. Keevil Inst. of Mining Engineering

2010-07-01

Mining is an energy-intensive industry, and most processing mills use wet processes to separate minerals from ore. This paper discussed water reduction, reuse and recycling options for a mining and mill operation network. A mine water network design was then proposed in order to identify and reduce water and system energy requirements. This included (1) a description of site water balance, (2) a description of potential water sources, (3) a description of water consumers, (4) the construction of energy requirement matrices, and (5) the use of linear programming to reduce energy requirements. The design was used to determine a site water balance as well as to specify major water consumers during mining and mill processes. Potential water supply combinations, water metering technologies, and recycling options were evaluated in order to identify the most efficient energy and water use combinations. The method was used to highlight potential energy savings from the integration of heating and cooling systems with plant water systems. 43 refs., 4 tabs., 3 figs.

Black holes with Yang-Mills hair

International Nuclear Information System (INIS)

Kleihaus, B.; Kunz, J.; Sood, A.; Wirschins, M.

1998-01-01

In Einstein-Maxwell theory black holes are uniquely determined by their mass, their charge and their angular momentum. This is no longer true in Einstein-Yang-Mills theory. We discuss sequences of neutral and charged SU(N) Einstein-Yang-Mills black holes, which are static spherically symmetric and asymptotically flat, and which carry Yang-Mills hair. Furthermore, in Einstein-Maxwell theory static black holes are spherically symmetric. We demonstrate that, in contrast, SU(2) Einstein-Yang-Mills theory possesses a sequence of black holes, which are static and only axially symmetric

Pulp mill as an energy producer

International Nuclear Information System (INIS)

Kaulamo, O.

1998-01-01

The recovery boilers of pulp mills are today the most significant producers of wood energy. The power-to-heat ratio of the power plant process, i.e., power yield, is poor in existing applications. In the study, an alternative of improving the power yield of conventional pulp mills significantly was studied by applying solutions used in power plants to a pulp mill. Extensive conversion of wood energy into electricity is possible only in the recovery boiler of the pulp mill and in a large combustion boiler of bark, wood waste and wood chips integrated to this boiler. Hence, the harvest and transports of wood raw materials, i.e. pulp wood and energy wood, are integrated, and the fraction going to cook and the energy wood fraction are separated at the pulp mill. The method guarantees competitive supply of energy wood. As a result a SELLUPOWER mill was designed, where the recovery boiler combusting black liquor and the large power plant boiler combusting energy wood are integrated to one unit and constructed to a power plant process with a high power-to-heat ratio. Necessary technical solutions, project costs and economical feasibility compared to a conventional pulp mill were determined, and the effect of different production-economical parameters was also studied. (orig.)

The Complete Chloroplast Genome Sequence of Tree of Heaven (Ailanthus altissima (Mill. (Sapindales: Simaroubaceae, an Important Pantropical Tree

Directory of Open Access Journals (Sweden)

Josphat K. Saina

2018-03-01

Full Text Available Ailanthus altissima (Mill. Swingle (Simaroubaceae is a deciduous tree widely distributed throughout temperate regions in China, hence suitable for genetic diversity and evolutionary studies. Previous studies in A. altissima have mainly focused on its biological activities, genetic diversity and genetic structure. However, until now there is no published report regarding genome of this plant species or Simaroubaceae family. Therefore, in this paper, we first characterized A. altissima complete chloroplast genome sequence. The tree of heaven chloroplast genome was found to be a circular molecule 160,815 base pairs (bp in size and possess a quadripartite structure. The A. altissima chloroplast genome contains 113 unique genes of which 79 and 30 are protein coding and transfer RNA (tRNA genes respectively and also 4 ribosomal RNA genes (rRNA with overall GC content of 37.6%. Microsatellite marker detection identified A/T mononucleotides as majority SSRs in all the seven analyzed genomes. Repeat analyses of seven Sapindales revealed a total of 49 repeats in A. altissima, Rhus chinensis, Dodonaea viscosa, Leitneria floridana, while Azadirachta indica, Boswellia sacra, and Citrus aurantiifolia had a total of 48 repeats. The phylogenetic analysis using protein coding genes revealed that A. altissima is a sister to Leitneria floridana and also suggested that Simaroubaceae is a sister to Rutaceae family. The genome information reported here could be further applied for evolution and invasion, population genetics, and molecular studies in this plant species and family.

John Stuart Mill: utilitarismo e liberalismo = John Stuart Mill: utilitarianism and liberalism

Directory of Open Access Journals (Sweden)

Simões, Mauro Cardoso

2013-01-01

Full Text Available Meu objetivo, neste trabalho, é investigar a compatibilidade das teses utilitaristas e liberais de John Stuart Mill. Apresentarei, inicialmente, os principais críticos da filosofia moral e política de Mill, para os quais o discípulo de Bentham teria abandonado o utilitarismo ou, ainda, não esclarecido suficientemente seu princípio da liberdade, o que o tornaria um pensador assistemático e inconsistente. Minha tese é contrária a tais interpretações, uma vez que sustenta ser Mill consistente. Em seguida, defenderei uma interpretação do princípio da liberdade e da individualidade, procurando demonstrar que seu utilitarismo é compatível com seu liberalismo

Decommissioning and disposal of foreign uranium mine and mill facilities

International Nuclear Information System (INIS)

Pan Yingjie; Xue Jianxin; Yuan Baixiang; Xu Lechang

2012-01-01

Disposal techniques in decommissioning of foreign uranium mine and mill facilities are systematically discussed, including covering of uranium tailing impoundment, drainaging and consolidation of uranium tailing, and treatment of mining waste water and polluted groundwater, and the costs associated with disposal are analyzed. The necessity of strengthening the decommissioning disposal technology research and international exchanges and cooperation is emphasized. (authors)

Numerical simulation study on rolling-chemical milling process of aluminum-lithium alloy skin panel

Science.gov (United States)

Huang, Z. B.; Sun, Z. G.; Sun, X. F.; Li, X. Q.

2017-09-01

Single curvature parts such as aircraft fuselage skin panels are usually manufactured by rolling-chemical milling process, which is usually faced with the problem of geometric accuracy caused by springback. In most cases, the methods of manual adjustment and multiple roll bending are used to control or eliminate the springback. However, these methods can cause the increase of product cost and cycle, and lead to material performance degradation. Therefore, it is of significance to precisely control the springback of rolling-chemical milling process. In this paper, using the method of experiment and numerical simulation on rolling-chemical milling process, the simulation model for rolling-chemical milling process of 2060-T8 aluminum-lithium alloy skin was established and testified by the comparison between numerical simulation and experiment results for the validity. Then, based on the numerical simulation model, the relative technological parameters which influence on the curvature of the skin panel were analyzed. Finally, the prediction of springback and the compensation can be realized by controlling the process parameters.

Optimization of FIB milling for rapid NEMS prototyping

DEFF Research Database (Denmark)

Malm, Bjarke; Petersen, Dirch Hjorth; Lei, Anders

2011-01-01

We demonstrate an optimized milling technique to focused ion beam (FIB) milling in template silicon membranes for fast prototyping of nanoelectromechanical systems (NEMS). Using a single-pass milling strategy the highly topology dependent sputtering rate is boosted and shorter milling time...... is achieved. Drift independence is obtained for small critical features using a radial scan strategy, and a back scan routine ensures minimal line width deviation removing redeposited material. Milling a design similar to a nano four-point probe with a pitch down to 400nm we display what optimized FIB milling...

Atomic disorder and amorphization of B2-structure CoZr by ball milling

International Nuclear Information System (INIS)

Zhou, G.F.; Bakker, H.

1996-01-01

For a considerable number of intermetallic compounds it has been found that ball milling introduces atomic (chemical) disorder. Disorder due to milling was demonstrated by x-ray diffraction in AlRu, crystallizing in the B2 structure (ordered b.c.c.) by a decrease of the intensity of superlattice reflections relative to fundamental reflections. The same technique was used to investigate disordering by milling in Ni 3 Al, crystallizing in the L1 2 structure (ordered f.c.c.). In both cases the disorder is anti-site disorder of both components, i.e. both atomic species substitute on the wrong sublattices. Besides x-ray diffraction measurements of magnetic properties turned out to be useful in monitoring structural changes due to milling. The change in the superconducting transition temperature, measured by magnetic a.c. susceptibility, was used to demonstrate atomic disordering by milling in Nb 3 Sn and Nb 3 Au. The type of disorder turned out to be anti-site disorder. Such a type of disorder occurs in the same materials also at high temperatures or after irradiation by neutrons. The disordering was accompanied by an increase of the lattice parameter. An increase in high-field magnetization accompanied by a decrease of the lattice parameter during milling was found in B2 CoGa and B2 CoAl. In principle in the completely ordered state both compounds are non-magnetic, because the CO atoms are shielded from one another by Ga and Al atoms, respectively. However, when a Co atom is transferred to the wrong sublattice, it is surrounded by Co atoms as nearest neighbors and bears a magnetic moment. This explains the strong increase of the magnetization due to milling

Reclamation plans at uranium mill tailings sites

International Nuclear Information System (INIS)

Abt, S.R.; Nelson, J.D.

1990-01-01

Long-term stability of waste impoundments is of concern because of the long time periods over which various types of waste may remain active. Over the past decade much technology has been developed specifically for reclamation of uranium mill tailings impoundments. Aspects of this technology will be discussed here and is presented as also being directly applicable to reclamation of industrial waste impoundments in general. The paper discusses Title I and Title II sites which represent two different generations in uranium tailings impoundment construction. The comparison between the two represent differences in philosophies as well as in impoundment type. Reclamation of uranium mill tailings impoundments in the U.S. is controlled by Federal legislation, which has set forth the regulatory framework for reclamation plan approval. Title I requirements govern government owned inactive sites and Title II requirements govern active tailings impoundments or those operated by private industries. While the Title I and Title II designation may result in a slightly different regulatory process, reclamation of uranium tailings sites has the same. Differences between Title I and Title II reclamation plans to achieve surface stability relate primarily to the embankment and surface covers. The differences in the cover designs result from site-specific conditions, rather than from differences in engineering approaches or the regulatory process. This paper discusses the site-specific conditions that affect the selection of cover designs, and provides a comparative example to illustrate the effect of this condition

Yang-Mills theory for non-semisimple groups

CERN Document Server

Nuyts, J; Nuyts, Jean; Wu, Tai Tsun

2003-01-01

For semisimple groups, possibly multiplied by U(1)'s, the number of Yang-Mills gauge fields is equal to the number of generators of the group. In this paper, it is shown that, for non-semisimple groups, the number of Yang-Mills fields can be larger. These additional Yang-Mills fields are not irrelevant because they appear in the gauge transformations of the original Yang-Mills fields. Such non-semisimple Yang-Mills theories may lead to physical consequences worth studying. The non-semisimple group with only two generators that do not commute is studied in detail.

Characterisation of Mn0.63Zn0.37Fe2O4 powders after intensive milling and subsequent thermal treatment

Directory of Open Access Journals (Sweden)

Labus Nebojša

2017-01-01

Full Text Available Commercial Mn-Zn powder (Mn0.63Zn0.37Fe2O4, 93 wt. % and Fe2O3 7 wt. % was milled 0.5, 1, 2 and 4 hours in a planetary ball mill. The goal was to observe intensive milling influences on oxidation and reduction processes that will happen during subsequent heating. Powders were characterized with XRD, SEM and particle seizer. Subsequent heating was monitored on TGA/DTA in an air atmosphere. After compaction of the milled powders, sintering was also performed in a dilatometric device. Sintered specimens were characterized micro structurally with SEM on a fresh breakage. Obtained differential TGA diagrams suggest intensive changes during prolonged milling of the oxidation kinetics on heating. Ferrite powders changed with milling as well as with second run heating were characterized to enable determination of the potentially best ratio of milling and heating to be applied to obtain the desired microstructure. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. OI172057 and Grant no. III45014

Chevron's Panna Maria mill process description

International Nuclear Information System (INIS)

Anon.

1979-01-01

Key features of Chevron's Uranium Mill located near Panna Maria, Texas, are described. The mill is designed to process a nominal 2500 dry tons/day of uranium bearing ore containing 15% uncombined moisture. The following operations at the mill are highlighted: ore receiving, grinding, leaching, countercurrent decantation and tailings disposal, filtering, solvent extraction, solvent stripping, precipitation, drying, and packaging

VOC Control in Kraft Mills; FINAL

International Nuclear Information System (INIS)

Zhu, J.Y.; Chai, X.-S.; Edwards, L.L.; Gu, Y.; Teja, A.S.; Kirkman, A.G.; Pfromm, P.H.; Rezac, M.E.

2001-01-01

The formation of volatile organic compounds (VOCs), such as methanol, in kraft mills has been an environmental concern. Methanol is soluble in water and can increase the biochemical oxygen demand. Furthermore, it can also be released into atmosphere at the process temperatures of kraft mill-streams. The Cluster Rule of the EPA now requires the control of the release of methanol in pulp and paper mills. This research program was conducted to develop a computer simulation tool for mills to predict VOC air emissions. To achieve the objective of the research program, much effort was made in the development of analytical techniques for the analysis of VOC and determination of vapor liquid partitioning coefficient of VOCs in kraft mill-streams using headspace gas chromatography. With the developed analytical tool, methanol formation in alkaline pulping was studied in laboratory to provide benchmark data of the amount of methanol formation in pulping in kraft mills and for the validation of VOC formation and vapor-liquid equilibrium submodels. Several millwide air and liquid samplings were conducted using the analytical tools developed to validate the simulation tool. The VOC predictive simulation model was developed based on the basic chemical engineering concepts, i.e., reaction kinetics, vapor liquid equilibrium, combined with computerized mass and energy balances. Four kraft mill case studies (a continuous digester, two brownstock washing lines, and a pre-evaporator system) are presented and compared with mill measurements. These case studies provide valuable, technical information for issues related to MACT I and MACT II compliance, such as condensate collection and Clean-Condensate-Alternatives (CCA)

In-situ grouting of uranium-mill-tailings piles: an assessment

International Nuclear Information System (INIS)

Tamura, T.; Boegly, W.J. Jr.

1983-05-01

Passage in 1978 of the Uranium Mill Tailings Radiation Control Act (UMTRCA) initiated a program of remedial action for 22 existing mill tailings piles generated in the period 1940 to 1970 as part of the nation's defense and nuclear power programs. The presence of these piles poses potential health and environmental contamination concerns. Possible remedial actions proposed include multilayer covers over the piles to reduce water infiltration, reduce radon gas releases, and reduce airborne transport of tailings fines. In addition, suggested remedial actions include (1) the use of liners to prevent groundwater contamination by leachates from the piles and (2) chemical stabilization of the tailings to retain the radioactive and nonradioactive sources of contamination. Lining of the piles would normally be applicable only to piles that are to be moved from their present location such that the liner could be placed between the tailings and the groundwater. However, by using civil engineering techniques developed for grouting rocks and soils for strength and water control, it may be possible to produce an in situ liner for piles that are not to be relocated. The Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project Office requested that ORNL assess the potential application of grouting as a remedial action. This report examines the types of grouts, the equipment available, and the costs, and assesses the possibility of applying grouting technology as a remedial action alternative for uranium mill tailings piles

In-situ grouting of uranium-mill-tailings piles: an assessment

Energy Technology Data Exchange (ETDEWEB)

Tamura, T.; Boegly, W.J. Jr.

1983-05-01

Passage in 1978 of the Uranium Mill Tailings Radiation Control Act (UMTRCA) initiated a program of remedial action for 22 existing mill tailings piles generated in the period 1940 to 1970 as part of the nation's defense and nuclear power programs. The presence of these piles poses potential health and environmental contamination concerns. Possible remedial actions proposed include multilayer covers over the piles to reduce water infiltration, reduce radon gas releases, and reduce airborne transport of tailings fines. In addition, suggested remedial actions include (1) the use of liners to prevent groundwater contamination by leachates from the piles and (2) chemical stabilization of the tailings to retain the radioactive and nonradioactive sources of contamination. Lining of the piles would normally be applicable only to piles that are to be moved from their present location such that the liner could be placed between the tailings and the groundwater. However, by using civil engineering techniques developed for grouting rocks and soils for strength and water control, it may be possible to produce an in situ liner for piles that are not to be relocated. The Department of Energy (DOE) Uranium Mill Tailings Remedial Action Project Office requested that ORNL assess the potential application of grouting as a remedial action. This report examines the types of grouts, the equipment available, and the costs, and assesses the possibility of applying grouting technology as a remedial action alternative for uranium mill tailings piles.

Treatment technologies of liquid and solid wastes from two-phase olive oil mills

Directory of Open Access Journals (Sweden)

Rincón, Bárbara

2006-03-01

Full Text Available Over the last 10 years the manufacture of olive oil has undergone important evolutionary changes in the equipment used for the separation of olive oil from the remaining components. The latest development has been the introduction of a two-phase centrifugation process in which a horizontally-mounted centrifuge is used for a primary separation of the olive oil fraction from the vegetable solid material and vegetation water. Therefore, the new two-phase olive oil mills produce three identifiable and separate waste streams. These are: 1 the wash waters from the initial cleansing of the fruit; 2 the wash waters from the secondary centrifuge and 3 the aqueous solid residues from the primary centrifugation. As well as offering process advantages they also reduce the water consumption of the mill. The introduction of this technology was carried out in 90% of Spanish olive oil factories. Therefore, the new twophase olive mill effluents (TPOME are made up of the mixture of effluents (1 and (2, the total volume of TPOME generated being around 0.25 l/kg of olives processed. In addition, the solid residue (two-phase olive pomace, TPOP has a high organic matter concentration giving an elevated polluting load and it cannot be easily handled by traditional technology which deals with the conventional three-phase olive cake.So, this paper aims to report the main features and characteristics of TPOME, and of TPOP, as compared to the classical olive mill wastewater (OMW and olive cake derived from the three-phase manufacturing process. The advantages and disadvantages of the two-phase decanting process will be summarized. Among the treatments reported for TPOME, aerobic processes in completely mixed and activated sludge reactor showed high COD removal efficiencies. Kinetic constants of the aerobic processes were also compared at different operational conditions. The report also includes the following findings: assays of anaerobic digestion of wastewaters from the

Galilean Yang-Mills theory

Energy Technology Data Exchange (ETDEWEB)

Bagchi, Arjun [Center for Theoretical Physics, Massachusetts Institute of Technology,77 Massachusetts Avenue, Cambridge, MA 02139 (United States); Basu, Rudranil [Saha Institute of Nuclear Physics,Block AF, Sector 1, Bidhannagar, Kolkata 700068 (India); Kakkar, Ashish [Indian Institute of Science Education and Research,Dr Homi Bhabha Road, Pashan. Pune 411008 (India); Mehra, Aditya [Indian Institute of Science Education and Research,Dr Homi Bhabha Road, Pashan. Pune 411008 (India); Van Swinderen Institute for Particle Physics and Gravity, University of Groningen, Nijenborgh 4, 9747 AG Groningen (Netherlands)

2016-04-11

We investigate the symmetry structure of the non-relativistic limit of Yang-Mills theories. Generalising previous results in the Galilean limit of electrodynamics, we discover that for Yang-Mills theories there are a variety of limits inside the Galilean regime. We first explicitly work with the SU(2) theory and then generalise to SU(N) for all N, systematising our notation and analysis. We discover that the whole family of limits lead to different sectors of Galilean Yang-Mills theories and the equations of motion in each sector exhibit hitherto undiscovered infinite dimensional symmetries, viz. infinite Galilean Conformal symmetries in D=4. These provide the first examples of interacting Galilean Conformal Field Theories (GCFTs) in D>2.

Galilean Yang-Mills theory

International Nuclear Information System (INIS)

Bagchi, Arjun; Basu, Rudranil; Kakkar, Ashish; Mehra, Aditya

2016-01-01

We investigate the symmetry structure of the non-relativistic limit of Yang-Mills theories. Generalising previous results in the Galilean limit of electrodynamics, we discover that for Yang-Mills theories there are a variety of limits inside the Galilean regime. We first explicitly work with the SU(2) theory and then generalise to SU(N) for all N, systematising our notation and analysis. We discover that the whole family of limits lead to different sectors of Galilean Yang-Mills theories and the equations of motion in each sector exhibit hitherto undiscovered infinite dimensional symmetries, viz. infinite Galilean Conformal symmetries in D=4. These provide the first examples of interacting Galilean Conformal Field Theories (GCFTs) in D>2.

Texture formation in iron particles using mechanical milling with graphite as a milling aid

Energy Technology Data Exchange (ETDEWEB)

Motozuka, S.; Hayashi, K. [Department of Mechanical Engineering, Gifu National College of Technology, 2236-2 Kamimakuwa, Motosu, Gifu 501-0495 (Japan); Tagaya, M. [Department of Materials Science and Technology, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka, Niigata 940-2188 (Japan); Morinaga, M. [Toyota Physical and Chemical Research Institute, 41-1, Yokomichi, Nagakute, Aichi 480-1192 (Japan)

2015-09-15

Crystallographically anisotropic platelet iron particles were successfully prepared using a conventional ball mill with addition of graphite (Gp) particles. The morphological and structural changes resulting from the milling were investigated using scanning electron microscopy and X-ray diffraction. The spherical iron particles were plastically deformed into platelet shapes during the milling. Simultaneously, it is suggested that the size of the Gp particles decreased and adhered as nanoparticles on the surface of the iron particles. The adhered Gp particles affected the plastic deformation behavior of the iron particles: the (001) planes of α-iron were oriented parallel to the particle face, and no preferred in-plane orientation was observed. This study not only details the preparation of soft magnetic metal particles that crystallographically oriented to enhance their magnetic properties but also provides new insight into the activities of the well-established and extensively studied mechanical milling method.

Texture formation in iron particles using mechanical milling with graphite as a milling aid

International Nuclear Information System (INIS)

Motozuka, S.; Hayashi, K.; Tagaya, M.; Morinaga, M.

2015-01-01

Crystallographically anisotropic platelet iron particles were successfully prepared using a conventional ball mill with addition of graphite (Gp) particles. The morphological and structural changes resulting from the milling were investigated using scanning electron microscopy and X-ray diffraction. The spherical iron particles were plastically deformed into platelet shapes during the milling. Simultaneously, it is suggested that the size of the Gp particles decreased and adhered as nanoparticles on the surface of the iron particles. The adhered Gp particles affected the plastic deformation behavior of the iron particles: the (001) planes of α-iron were oriented parallel to the particle face, and no preferred in-plane orientation was observed. This study not only details the preparation of soft magnetic metal particles that crystallographically oriented to enhance their magnetic properties but also provides new insight into the activities of the well-established and extensively studied mechanical milling method

Simulation of activational grinding for rhombic sulfur particles in a disintegrator (pinned disc mill

Directory of Open Access Journals (Sweden)

Farit Urakaev

2016-12-01

Full Text Available Based on the theoretical studies, complete picture of a mechanical processing of sulfur in the disintegrator is given. Kinematic and dynamic characteristics of elastic and inelastic collisions of particles of processed rhombic sulfur with rows of disintegrator fingers are calculated. Based on the analysis of the obtained dependency of the rotation frequency of the rotors offers, advices on selecting optimal conditions for activation milling of α-sulfur in the disintegrator are given. These results can be partially used in the processing of sulfur and in other types of shock grinding devices, in particular, jet mills.

Loop Amplitudes in Pure Yang-Mills from Generalised Unitarity

OpenAIRE

Brandhuber, Andreas; McNamara, Simon; Spence, Bill; Travaglini, Gabriele

2005-01-01

We show how generalised unitarity cuts in D = 4 - 2 epsilon dimensions can be used to calculate efficiently complete one-loop scattering amplitudes in non-supersymmetric Yang-Mills theory. This approach naturally generates the rational terms in the amplitudes, as well as the cut-constructible parts. We test the validity of our method by re-deriving the one-loop ++++, -+++, --++, -+-+ and +++++ gluon scattering amplitudes using generalised quadruple cuts and triple cuts in D dimensions.

Loop amplitudes in pure Yang-Mills from generalised unitarity

International Nuclear Information System (INIS)

Brandhuber, Andreas; McNamara, Simon; Spence, Bill; Travaglini, Gabriele

2005-01-01

We show how generalised unitarity cuts in D = 4-2ε dimensions can be used to calculate efficiently complete one-loop scattering amplitudes in non-supersymmetric Yang-Mills theory. This approach naturally generates the rational terms in the amplitudes, as well as the cut-constructible parts. We test the validity of our method by re-deriving the one-loop ++++, -+++, --++, -+-+ and +++++ gluon scattering amplitudes using generalised quadruple cuts and triple cuts in D dimensions

Loop amplitudes in pure Yang-Mills from generalised unitarity

Energy Technology Data Exchange (ETDEWEB)

Brandhuber, Andreas [Department of Physics, Queen Mary, University of London, Mile End Road, London, E1 4NS (United Kingdom); McNamara, Simon [Department of Physics, Queen Mary, University of London, Mile End Road, London, E1 4NS (United Kingdom); Spence, Bill [Department of Physics, Queen Mary, University of London, Mile End Road, London, E1 4NS (United Kingdom); Travaglini, Gabriele [Department of Physics, Queen Mary, University of London, Mile End Road, London, E1 4NS (United Kingdom)

2005-10-15

We show how generalised unitarity cuts in D = 4-2{epsilon} dimensions can be used to calculate efficiently complete one-loop scattering amplitudes in non-supersymmetric Yang-Mills theory. This approach naturally generates the rational terms in the amplitudes, as well as the cut-constructible parts. We test the validity of our method by re-deriving the one-loop ++++, -+++, --++, -+-+ and +++++ gluon scattering amplitudes using generalised quadruple cuts and triple cuts in D dimensions.

Use of Residual Solids from Pulp and Paper Mills for Enhancing Strength and Durability of Ready-Mixed Concrete

Energy Technology Data Exchange (ETDEWEB)

Tarun R. Naik; Yoon-moon Chun; Rudolph N. Kraus

2003-09-18

This research was conducted to establish mixture proportioning and production technologies for ready-mixed concrete containing pulp and paper mill residual solids and to study technical, economical, and performance benefits of using the residual solids in the concrete. Fibrous residuals generated from pulp and paper mills were used, and concrete mixture proportions and productions technologies were first optimized under controlled laboratory conditions. Based on the mixture proportions established in the laboratory, prototype field concrete mixtures were manufactured at a ready-mixed concrete plant. Afterward, a field construction demonstration was held to demonstrate the production and placement of structural-grade cold-weather-resistant concrete containing residual solids.

Four pillars of radio astronomy Mills, Christiansen, Wild, Bracewell

CERN Document Server

Frater, R H; Wendt, H W

2017-01-01

This is the story of Bernie Mills, Chris Christiansen, Paul Wild and Ron Bracewell, members of a team of radio astronomers that would lead Australia, and the world, into this new field of research. Each of the four is remembered for his remarkable work: Mills for the development the cross type instrument that now bears his name; Christiansen for the application of rotational synthesis techniques; Wild for the masterful joining of observations and theory to elicit the nature of the solar atmosphere; Bracewell for his contribution to imaging theory. As well, these Four Pillars are remembered for creating a remarkable environment for scientific discovery and for influencing the careers of future generations. Their pursuit of basic science helped pave the way for technological developments in areas ranging from Wi-Fi to sonar to medical imaging to air navigation, and for underpinning the foundations of modern cosmology and astrophysics.

Magnetic properties of ball-milled Fe0.6Mn0.1Al0.3 alloys

International Nuclear Information System (INIS)

Rebolledo, A.F.; Romero, J.J.; Cuadrado, R.; Gonzalez, J.M.; Pigazo, F.; Palomares, F.J.; Medina, M.H.; Perez Alcazar, G.A.

2007-01-01

The FeMnAl-disordered alloy system exhibits, depending on the composition and the temperature, a rich variety of magnetic phases including the occurrence of ferromagnetism, antiferromagnetism, paramagnetism and spin-glass and reentrant spin glass behaviors. These latter phases result from the presence of atomic disorder and magnetic dilution and from the competing exchange interactions taking place between an Fe atom and its Mn and Fe first neighbors. The use of mechanical alloying in order to prepare these alloys is specially interesting since it allows to introduce in a progressive way large amounts of disorder. In this work, we describe the evolution with the milling time of the temperature dependence of the magnetic properties of mechanically alloyed Fe 0.6 Mn 0.1 Al 0.3 samples. The materials were prepared in a planetary ball mill using a balls-to-powder mass ratio of 15:1 and pure (99.95 at%) Fe, Mn and Al powders for times up to 19 h. The X-rays diffraction (XRD) spectra show the coexistence of three phases at short milling times. For milling times over 6 h, only the FeMnAl ternary alloy BCC phase is observed. Moesbauer spectroscopy reveals the complete formation of the FeMnAl alloy after 9 h milling time. The magnetic characterization showed that all the samples were ferromagnetic at room temperature with coercivities decreasing from 105 Oe (3 h milled sample) down to 5 Oe in the case of the sample milled for 19 h

Complete Dentures Fabricated with CAD/CAM Technology and a Traditional Clinical Recording Method.

Science.gov (United States)

Janeva, Nadica; Kovacevska, Gordana; Janev, Edvard

2017-10-15

The introduction of computer-aided design/computer-aided manufacturing (CAD/CAM) technology into complete denture (CD) fabrication ushered in a new era in removable prosthodontics. Commercially available CAD/CAM denture systems are expected to improve upon the disadvantages associated with conventional fabrication. The purpose of this report is to present the workflow involved in fabricating a CD with a traditional clinical recording method and CAD/CAM technology and to summarize the advantages to the dental practitioner and the patient.

Current uranium mill licensing issues

International Nuclear Information System (INIS)

Scarano, R.A.

1977-01-01

The problems encountered to insure environmentally safe mining and milling of uranium ores are reviewed. Emphasis is placed on the management of tailings resulting from milling operations. It is pointed out that although the concentration of radioactivity in the tailings is relatively low, control measures are necessary because of the large quantities involved and because of the long half-life of the parent radionuclides present. The major concerns with mill tailings are radon release to the atmosphere and isolation of the tailings from the human environment. Since it is anticipated that the amount of tailings created by the year 2000 will be more than an order of magnitude greater than the quantities that have been generated during the past 30 years, it is recommended that all mill tailings storage areas be located remote from public contact and in areas such that disruption and dispersion by natural forces and seepage of toxic materials into ground water systems are reduced to the maximum extent achievable. Technical issues that receive attention during the NRC licensing process for uranium mills and the preparation of environmental impact statements are discussed briefly

Would John Stuart Mill have regulated pornography?

OpenAIRE

McGlynn, C.; Ward, I.

2014-01-01

John Stuart Mill dominates contemporary pornography debates where he is routinely invoked as an authoritative defence against regulation. This article, by contrast, argues that a broader understanding of Mill's ethical liberalism, his utilitarianism, and his feminism casts doubt over such an assumption. New insights into Mill's approach to sex, sexual activity, and the regulation of prostitution reveal an altogether more nuanced and activist approach. We conclude that John Stuart Mill would a...

Improving milling and production of a dust-producing unit equipped with hammer mills

Energy Technology Data Exchange (ETDEWEB)

Vorotnikov, Ye.G.; Nikiforov, A.A.; Rasputin, O.V.; Sukhunin, V.I.

1982-01-01

This paper presents generalized experience for deriving coarse ground coal dust in hammer mills by providing comparison data on improving efficiency of operation of the unit when switching to a coarser-type grind of the fuel. Need to have more precise formulas to calculate grinding potential of hammer mills when using a coarser grind is shown.

Wear of micro end mills

DEFF Research Database (Denmark)

Bissacco, Giuliano; Hansen, Hans Nørgaard; De Chiffre, Leonardo

2005-01-01

This paper addresses the important issue of wear on micro end mills considering relevant metrological tools for its characterization and quantification. Investigation of wear on micro end mills is particularly difficult and no data are available in the literature. Small worn volumes cause large...... part. For this investigation 200 microns end mills are considered. Visual inspection of the micro tools requires high magnification and depth of focus. 3D reconstruction based on scanning electron microscope (SEM) images and stereo-pair technique is foreseen as a possible method for quantification...

Retrieving Storm Electric Fields from Aircrfaft Field Mill Data: Part II: Applications

Science.gov (United States)

Koshak, William; Mach, D. M.; Christian H. J.; Stewart, M. F.; Bateman M. G.

2006-01-01

The Lagrange multiplier theory developed in Part I of this study is applied to complete a relative calibration of a Citation aircraft that is instrumented with six field mill sensors. When side constraints related to average fields are used, the Lagrange multiplier method performs well in computer simulations. For mill measurement errors of 1 V m(sup -1) and a 5 V m(sup -1) error in the mean fair-weather field function, the 3D storm electric field is retrieved to within an error of about 12%. A side constraint that involves estimating the detailed structure of the fair-weather field was also tested using computer simulations. For mill measurement errors of 1 V m(sup -l), the method retrieves the 3D storm field to within an error of about 8% if the fair-weather field estimate is typically within 1 V m(sup -1) of the true fair-weather field. Using this type of side constraint and data from fair-weather field maneuvers taken on 29 June 2001, the Citation aircraft was calibrated. Absolute calibration was completed using the pitch down method developed in Part I, and conventional analyses. The resulting calibration matrices were then used to retrieve storm electric fields during a Citation flight on 2 June 2001. The storm field results are encouraging and agree favorably in many respects with results derived from earlier (iterative) techniques of calibration.

Chemically milled alpha-case layer from Ti-6Al-4V alloy investment cast

CSIR Research Space (South Africa)

Mutombo, K

2011-06-01

Full Text Available The as cast Ti6Al4V, obtained after investment casting with yttria stabilized zirconia face-coat, was chemically milled using a mixture of hydrofluoric acid and nitric acid. This process removed completely the alpha-case layer. Lower hardness...

Effects of milling on functional properties of rice flour.

Science.gov (United States)

Kadan, R S; Bryant, R J; Miller, J A

2008-05-01

A commercial long-grain rice flour (CRF) and the flours made by using a pin mill and the Udy mill from the same batch of broken second-head white long-grain rice were evaluated for their particle size and functional properties. The purpose of this study was to compare the commercial rice flour milling method to the pin and Udy milling methods used in our laboratory and pilot plant. The results showed that pin milled flour had more uniform particle size than the other 2 milled flours. The chalky kernels found in broken white milled rice were pulverized more into fines in both Udy milled flour and CRF than in the pin milled flour. The excessive amount of fines in flours affected their functional properties, for example, WSI and their potential usage in the novel foods such as rice breads (RB). The RB made from CRF collapsed more than loaves made from pin milled Cypress long-grain flours.

Challenges with modifications of the McClean Lake mill to process midwest ore

International Nuclear Information System (INIS)

Nguyen, T.T.; Backham, L.

2010-01-01

Midwest is a unique uranium deposit with exceptionally high arsenic content. The ore body is located 17 km west of the McClean Lake operation. The McClean Lake mill will be modified to process Midwest ore and handle solid wastes from the Midwest water treatment plant. This paper describes the modifications required of the McClean Lake mill, process challenges associated with treatment of the arsenic, and the possibility of recovering nickel and cobalt as a by-product. It also reviews the complexity in the design of the Midwest water treatment facility which incorporates reverse osmosis technology with conventional physical-chemical water treatment. (author)

Reformation and utilization of complicated topography for a uranium mill

International Nuclear Information System (INIS)

Liu Taoan; Zhou Xinghuo; Lv Junwen

2004-01-01

It is successful for how to reform and utilized complicated topography in the design of general plan and transport for technological reformation of a uranium mill. The unfavorable factors of complicated topography are turned into favorable ones. The general plan is designed compactly and the land is economized. The transport is designed simply and directly. the leaching liquid flows by gravity so that the power is economical

77 FR 14837 - Bioassay at Uranium Mills

Science.gov (United States)

2012-03-13

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0057] Bioassay at Uranium Mills AGENCY: Nuclear Regulatory..., ``Bioassay at Uranium Mills.'' This guide describes a bioassay program acceptable to the NRC staff for uranium mills and applicable portions of uranium conversion facilities where the possibility of exposure...

Biogeochemistry of uranium mill wastes program overview and conclusions

International Nuclear Information System (INIS)

Dreesen, D.R.

1981-05-01

The major findings and conclusions are summarized for research on uranium mill tailings for the US Department of Energy and the US Nuclear Regulatory Commission. An overview of results and interpretations is presented for investigations of 222 Rn emissions, revegetation of tailings and mine spoils, and trace element enrichment, mobility, and bioavailability. A brief discussion addresses the implications of these findings in relation to tailings disposal technology and proposed uranium recovery processes

Electron backscatter diffraction applied to lithium sheets prepared by broad ion beam milling.

Science.gov (United States)

Brodusch, Nicolas; Zaghib, Karim; Gauvin, Raynald

2015-01-01

Due to its very low hardness and atomic number, pure lithium cannot be prepared by conventional methods prior to scanning electron microscopy analysis. Here, we report on the characterization of pure lithium metallic sheets used as base electrodes in the lithium-ion battery technology using electron backscatter diffraction (EBSD) and X-ray microanalysis using energy dispersive spectroscopy (EDS) after the sheet surface was polished by broad argon ion milling (IM). No grinding and polishing were necessary to achieve the sufficiently damage free necessary for surface analysis. Based on EDS results the impurities could be characterized and EBSD revealed the microsctructure and microtexture of this material with accuracy. The beam damage and oxidation/hydration resulting from the intensive use of IM and the transfer of the sample into the microscope chamber was estimated to be effect on the surface temperature. However, a cryo-stage should be used if available during milling to guaranty a heating artefact free surface after the milling process. © 2014 Wiley Periodicals, Inc.

40 CFR 61.142 - Standard for asbestos mills.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Standard for asbestos mills. 61.142... § 61.142 Standard for asbestos mills. (a) Each owner or operator of an asbestos mill shall either discharge no visible emissions to the outside air from that asbestos mill, including fugitive sources, or...

UMTRA -- The US Uranium Mill Tailings Remedial Action Project

International Nuclear Information System (INIS)

Lightner, R.; Cormier, C.; Bierley, D.

1995-01-01

In the late 1970s, the United States (US) established the first comprehensive regulatory structure for the management, disposal, and long-term care of wastes produced from its domestic uranium processing industry. This regulatory framework was established through the passage of the Uranium Mill Tailings Radiation Control Act of 1978, often referred to as UMTRCA. This legislation created the Uranium Mill Tailings Remedial Action (UMTRA) Project and assigned the US Department of Energy (DOE) the lead in conducting the required remedial action at 24 designated inactive uranium ore processing sites. With the majority of these 22 sites complete, the DOE's UMTRA Project has established a distinguished reputation for safely and effectively remediating these low-level waste sites in a complex regulatory and socioeconomic environment. This paper describes the past accomplishments and current status of the UMTRA Project and discusses the DOE's plans for addressing ground water contamination associated with these sites and its commitment to continuing the long-term care and management of these disposal cells

Hydrogen storage performances of LaMg{sub 11}Ni + x wt% Ni (x = 100, 200) alloys prepared by mechanical milling

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yanghuan, E-mail: zhangyh59@sina.com [Key Laboratory of Integrated Exploitation of Baiyun Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Department of Functional Material Research, Central Iron and Steel Research Institute, Beijing 100081 (China); Wang, Haitao [Key Laboratory of Integrated Exploitation of Baiyun Obo Multi-Metal Resources, Inner Mongolia University of Science and Technology, Baotou 014010 (China); Department of Functional Material Research, Central Iron and Steel Research Institute, Beijing 100081 (China); Zhai, Tingting; Yang, Tai; Yuan, Zeming; Zhao, Dongliang [Department of Functional Material Research, Central Iron and Steel Research Institute, Beijing 100081 (China)

2015-10-05

Highlights: • Amorphous and nanostructured alloys were prepared by mechanical milling. • The maximum discharge capacity of ball milled alloys reaches to 1053.5 mA h/g. • The addition of Ni significantly increases the discharge capacity. • Increasing milling time reduces the kinetic performances of ball milled alloys. - Abstract: In order to improve the hydrogen storage performances of Mg-based materials, LaMg{sub 11}Ni alloy was prepared by vacuum induction melting. Then the nanocrystalline/amorphous LaMg{sub 11}Ni + x wt% Ni (x = 100, 200) hydrogen storage alloys were synthesized by ball milling technology. The structure characterizations of the alloys were carried out by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical hydrogen storage characteristics were tested by using programmed control battery testing system. The electrochemical impedance spectra (EIS), potentiodynamic polarization curves and potential-step curves were also plotted by an electrochemical workstation (PARSTAT 2273). The results indicate that the as-milled alloys exhibit a nanocrystalline and amorphous structure, and the amorphization degree of the alloys visibly increases with extending milling time. Prolonging the milling duration markedly enhances the electrochemical discharge capacity and cyclic stability of the alloys. The electrochemical kinetics, including high rate discharge ability (HRD), charge transfer rate, limiting current density (I{sub L}), hydrogen diffusion coefficient (D), monotonously decrease with milling time prolonging.

Yang-Mills theory in Coulomb gauge; Yang-Mills-theorie in Coulombeichung

Energy Technology Data Exchange (ETDEWEB)

Feuchter, C.

2006-07-01

In this thesis we study the Yang-Mills vacuum structure by using the functional Schroedinger picture in Coulomb gauge. In particular we discuss the scenario of colour confinement, which was originally formulated by Gribov. After a short introduction, we recall some basic aspects of Yang-Mills theories, its canonical quantization in the Weyl gauge and the functional Schroedinger picture. We then consider the minimal Coulomb gauge and the Gribov problem of the gauge theory. The gauge fixing of the Coulomb gauge is done by using the Faddeev-Popov method, which enables the resolution of the Gauss law - the constraint on physical states. In the third chapter, we variationally solve the stationary Yang-Mills Schroedinger equation in Coulomb gauge for the vacuum state. Therefor we use a vacuum wave functional, which is strongly peaked at the Gribov horizon. The vacuum energy functional is calculated and minimized resulting in a set of coupled Schwinger-Dyson equations for the gluon energy, the ghost and Coulomb form factors and the curvature in gauge orbit space. Using the angular approximation these integral equations have been solved analytically in both the infrared and the ultraviolet regime. The asymptotic analytic solutions in the infrared and ultraviolet regime are reasonably well reproduced by the full numerical solutions of the coupled Schwinger-Dyson equations. In the fourth chapter, we investigate the dependence of the Yang-Mills wave functional in Coulomb gauge on the Faddeev-Popov determinant. (orig.)

Model-based Process Monitoring and Control of Micro-milling using Active Magnetic Bearings

NARCIS (Netherlands)

Blom, R.S.

2011-01-01

The process of micro-milling is a promising technology for the fabrication of micro-parts with arbitrary 3D features in a wide range of materials. However, as a result of the reduced dimensions, the susceptibility of the process for machine tool errors and vibrations is higher, having adverse

Uranium mill tailings management practices in Saskatchewan, Canada

International Nuclear Information System (INIS)

Clifton, A.W.; Barsi, R.G.; Melis, L.A.

1984-01-01

Uranium was discovered in Saskatchewan in 1934. The first major mill began operating at Beaverlodge in 1953; two other mills began production in the same area in 1955 and 1957. Waste management measures were limited at the early mills. A new generation of mills was brought into production beginning in 1975 utilizing engineered waste management systems. The paper presents a brief description of the geography and physical environment of northern Saskatchewan, Canada; reviews milling operations and waste managements systems; describes the evolution of waste management systems; and, comments on environmental control measures regulating the industry

Implementation of the Additional Protocol: Verification activities at uranium mines and mills

International Nuclear Information System (INIS)

Bragin, V.; Carlson, J.; Leslie, R.

2001-01-01

verify uranium production at the mine site per se would be both extremely difficult and time consuming. In any case, access to all parts of an underground mining operation could not be guaranteed during a short notice visit. Verification is feasible only at the last stage of the process where the uranium is present in a relatively pure form. Accordingly, on-site activities suggested in this paper focus on confirming consistency between declarations and likely production (to the extent that that is possible) at the product end of the mill, which is much the same for all technologies. The extent to which the Agency can have confidence in the production declared may depend on the degree of independent information available to corroborate production figures. While corroborating evidence may not verify production per se, it does provide an additional level of assurance that the information contained in a declaration is reasonably accurate and complete, provided the information comes from an independent source. Environmental sampling techniques (eg detection of gamma emitting radionuclides of uranium/thorium decay daughters, perhaps in tails) could also prove useful during on-site visits, particularly when inspecting those operations which may, for example, mine for six months of the year and mill for the remainder of the year. Absence of comparatively short-lived decay products in effluents would be indicative that the daughters had not been in recent contact with the parent, and thus that the mill had not been in recent operation. Th-234 (a daughter in the U-238 decay chain), with a half-life of some 24 days, would seem an ideal candidate to look for in determining whether a mill had been in recent operation. As an aside, it should be noted that environmental sampling could also prove a useful technique in providing to inspectors an additional level of assurance that undeclared nuclear activities, such as conversion or enrichment, were not being carried out clandestinely in

Blue-shift in photoluminescence of ion-milled HgCdTe films and relaxation of defects induced by the milling

International Nuclear Information System (INIS)

Pociask, M.; Izhnin, I.I.; Mynbaev, K.D.; Izhnin, A.I.; Dvoretsky, S.A.; Mikhailov, N.N.; Sidorov, Yu.G.; Varavin, V.S.

2010-01-01

Simultaneous measurements of electrical conductivity, the Hall coefficient, and photoluminescence (PL) spectra of ion-milled Hg 1 - x Cd x Te films (x ∼ 0.30 and 0.38) were performed during post-milling ageing of the films at 293 K. In the course of the PL study, a 'relaxation' of the blue-shift of the PL band of ion-milled Hg 0.70 Cd 0.30 Te was observed. The relaxation was caused by the decrease of the electron concentration due to gradual disintegration of defects induced by the milling. It is shown that while ion milling substantially changes the electrical properties of Hg 1 - x Cd x Te, its PL spectrum in the long-term is affected insignificantly.

KSC ADVANCED GROUND BASED FIELD MILL V1

Data.gov (United States)

National Aeronautics and Space Administration — The Advanced Ground Based Field Mill (AGBFM) network consists of 34 (31 operational) field mills located at Kennedy Space Center (KSC), Florida. The field mills...

Loop quantum corrected Einstein Yang-Mills black holes

Science.gov (United States)

Protter, Mason; DeBenedictis, Andrew

2018-05-01

In this paper, we study the homogeneous interiors of black holes possessing SU(2) Yang-Mills fields subject to corrections inspired by loop quantum gravity. The systems studied possess both magnetic and induced electric Yang-Mills fields. We consider the system of equations both with and without Wilson loop corrections to the Yang-Mills potential. The structure of the Yang-Mills Hamiltonian, along with the restriction to homogeneity, allows for an anomaly-free effective quantization. In particular, we study the bounce which replaces the classical singularity and the behavior of the Yang-Mills fields in the quantum corrected interior, which possesses topology R ×S2 . Beyond the bounce, the magnitude of the Yang-Mills electric field asymptotically grows monotonically. This results in an ever-expanding R sector even though the two-sphere volume is asymptotically constant. The results are similar with and without Wilson loop corrections on the Yang-Mills potential.

Energy efficiency improvement and cost saving opportunities for the Corn Wet Milling Industry: An ENERGY STAR Guide for Energy and Plant Managers

Energy Technology Data Exchange (ETDEWEB)

Galitsky, Christina; Worrell, Ernst; Ruth, Michael

2003-07-01

Corn wet milling is the most energy intensive industry within the food and kindred products group (SIC 20), using 15 percent of the energy in the entire food industry. After corn, energy is the second largest operating cost for corn wet millers in the United States. A typical corn wet milling plant in the United States spends approximately $20 to $30 million per year on energy, making energy efficiency improvement an important way to reduce costs and increase predictable earnings, especially in times of high energy-price volatility. This report shows energy efficiency opportunities available for wet corn millers. It begins with descriptions of the trends, structure and production of the corn wet milling industry and the energy used in the milling and refining process. Specific primary energy savings for each energy efficiency measure based on case studies of plants and references to technical literature are provided. If available, typical payback periods are also listed. The report draws upon the experiences of corn, wheat and other starch processing plants worldwide for energy efficiency measures. The findings suggest that given available resources and technology, there are opportunities to reduce energy consumption cost-effectively in the corn wet milling industry while maintaining the quality of the products manufactured. Further research on the economics of the measures, as well as the applicability of these to different wet milling practices, is needed to assess the feasibility of implementation of selected technologies at individual plants.

Development of uranium milling and conversion

International Nuclear Information System (INIS)

Takada, Shingo; Hirono, Shuichiro.

1983-11-01

The development and improvement of uranium milling and refining producing uranium tetrafluoride from ores by the wet process, without producing yellowcake as an intermediate product, have been carried out for over ten years with a small pilot plant (50 t-ore/day). In the past several years, a process for converting uranium tetrafluoride into hexafluoride has been developed successfully. To develop the process further, the construction of an integrated milling and conversion pilot plant (200 t-U/year) started in 1979 and was completed in 1981. This new plant has two systems of solvent extraction using tri-noctylamine: one of the systems treats the pregnant solution (uranyl sulphate) by heap-leaching followed by ion exchange, and the other treats the uranyl sulphate solution by dissolving imported yellowcake. The uranium loading solvents from the two systems are stripped with hydrochloric acid solution to obtain the concentrated uranium solution containing 100 g-U/1. Uranyl sulphate solution from the stripping circuit is reduced to a uranous sulphate solution by the electrolytic method. In a reduction cell, uranyl sulphate solution and dilute sulphuric acid are used respectively as catholyte and anolyte, and a cation exchange membrane is used to prevent re-oxidation of the uranous sulphate. In the following hydrofluorination step, uranium tetrafluoride, UF 4 .1-1.2H 2 O (particle size: 50-100μ), is produced continuously as the precipitate in an improved reaction vessel, and this makes it possible to simplify the procedures of liquid-solid separation, drying and granulation. The uranium tetrafluoride is dehydrated by heating to 350 0 C in an inert gas flow. The complete conversion from UF 4 into UF 6 is achieved by a fluidized-bed reactor and a high value of utilization efficiency of fluorine, over 99.9 percent, is attained at about 400 0 C. (author)

Estimated dose to man from uranium milling via the terrestrial food-chain pathway

Energy Technology Data Exchange (ETDEWEB)

Rayno, D.R.

1982-01-01

One of the major pathways of radiological exposure to man from uranium milling operations is through the terrestrial food chain. Studies by various investigators have shown the extent of uptake and distribution of U-238, U-234, Th-230, Ra-226, Pb-210, and Po-210 in plants and animals. These long-lived natural radioisotopes, all nuclides of the uranium decay series, are found in concentrated amounts in uranium mill tailings. Data from these investigations are used to estimate the dose to man from consumption of beef and milk contaminated by the tailings. This dose estimate from this technologically enhanced source is compared with that from average normal dietary intake of these radionuclides from natural sources.

Estimated dose to man from uranium milling via the terrestrial food-chain pathway

International Nuclear Information System (INIS)

Rayno, D.R.

1982-01-01

One of the major pathways of radiological exposure to man from uranium milling operations is through the terrestrial food chain. Studies by various investigators have shown the extent of uptake and distribution of U-238, U-234, Th-230, Ra-226, Pb-210, and Po-210 in plants and animals. These long-lived natural radioisotopes, all nuclides of the uranium decay series, are found in concentrated amounts in uranium mill tailings. Data from these investigations are used to estimate the dose to man from consumption of beef and milk contaminated by the tailings. This dose estimate from this technologically enhanced source is compared with that from average normal dietary intake of these radionuclides from natural sources

Remedial action plan and site design for stabilization of the inactive uranium mill tailings sites at Rifle, Colorado

Energy Technology Data Exchange (ETDEWEB)

1992-02-01

This appendix assesses the present conditions and data gathered about the two inactive uranium mill tailings sites near Rifle, Colorado, and the designated disposal site six miles north of Rifle in the area of Estes Gulch. It consolidates available engineering, radiological, geotechnical, hydrological, meteorological, and other information pertinent to the design of the Remedial Action Plan (RAP). The data characterize conditions at the mill, tailings, and disposal site so that the Remedial Action Contractor (RAC) may complete final designs for the remedial actions.

ROMI 4.0: Updated Rough Mill Simulator

Science.gov (United States)

Timo Grueneberg; R. Edward Thomas; Urs Buehlmann

2012-01-01

In the secondary hardwood industry, rough mills convert hardwood lumber into dimension parts for furniture, cabinets, and other wood products. ROMI 4.0, the US Department of Agriculture Forest Service's ROugh-MIll simulator, is a software package designed to simulate the cut-up of hardwood lumber in rough mills in such a way that a maximum possible component yield...

Optimisation of milling parameters using neural network

Directory of Open Access Journals (Sweden)

Lipski Jerzy

2017-01-01

Full Text Available The purpose of this study was to design and test an intelligent computer software developed with the purpose of increasing average productivity of milling not compromising the design features of the final product. The developed system generates optimal milling parameters based on the extent of tool wear. The introduced optimisation algorithm employs a multilayer model of a milling process developed in the artificial neural network. The input parameters for model training are the following: cutting speed vc, feed per tooth fz and the degree of tool wear measured by means of localised flank wear (VB3. The output parameter is the surface roughness of a machined surface Ra. Since the model in the neural network exhibits good approximation of functional relationships, it was applied to determine optimal milling parameters in changeable tool wear conditions (VB3 and stabilisation of surface roughness parameter Ra. Our solution enables constant control over surface roughness parameters and productivity of milling process after each assessment of tool condition. The recommended parameters, i.e. those which applied in milling ensure desired surface roughness and maximal productivity, are selected from all the parameters generated by the model. The developed software may constitute an expert system supporting a milling machine operator. In addition, the application may be installed on a mobile device (smartphone, connected to a tool wear diagnostics instrument and the machine tool controller in order to supply updated optimal parameters of milling. The presented solution facilitates tool life optimisation and decreasing tool change costs, particularly during prolonged operation.

Properties and sinterability of wet and dry attrition-milled OREOXed powder

International Nuclear Information System (INIS)

Lee, J. W.; Kim, J. H.; Kim, W. K.; Park, K. I.; Lee, J. W.

2001-01-01

The powder properties and sinterability were investigated with the powder prepared by wet and dry attrition milling of OREOX-treated powder. The OREOX-treated powder was prepared from the simulated spent fuel. Powder having less than 1 μm of average particle size could be obtained by dry milling, but not be obtained by wet milling. Thus, specific surface area of dry milled powder was higher than that of wet milled powder. With increasing of milling time, dry milled powder formed dense agglomerate while wet milled powder showed loose agglomerate. The pellets with higher than 95% T.D. of sintered density and larger than 7 μm of grain size were made with the milled powder regardless of milling method. The milling time in wet milling has greatly improved the sinterability. The pellets produced with dry milled powder have higher sintered density and larger grain size

Comparison of various milling modes combined to the enzymatic hydrolysis of lignocellulosic biomass for bioenergy production: Glucose yield and energy efficiency

International Nuclear Information System (INIS)

Licari, A.; Monlau, F.; Solhy, A.; Buche, P.; Barakat, A.

2016-01-01

Bagasse is an abundant by-product from sugarcane production that can be used for conversion into biofuels. Nonetheless, the recalcitrant structures of lignocellulosic fibers required a pretreatment prior conversion into biofuels. In this study, four mechanical deconstruction methods were compared in terms of energy demand and energy efficiency at lab scale: BM (ball mill), VBM (vibratory ball mill), CM (centrifugal mill) and JM (jet mill). Results indicate that VBM was more effective compared to BM, JM and CM in enzymatic accessibility and sugars solubilization: VBM-3h > BM-72 h > JM-5000 rpm > CM-0.12 mm. However, preliminary energetic assessment showed that at lab scale, the CM (centrifugal mill) as mechanical fractionation process appears to be the most efficient in terms of energy-efficiency (kg glucose/kWh) compared to BM, VBM and JM. A comparison with literature pretreatments data highlighted that fine and/or ultrafine milling process (BM, VBM, CM) are simpler saccharification technologies, which not required any chemical or water inputs, thus minimizing waste generation and treatment. - Highlights: • VBM (vibro ball milling) was the most effective in decreasing of cellulose crystallinity. • BM (ball milling) was the most effective in increasing surface area. • The highest energy efficiency was obtained with CM (centrifugal milling).

Pavement maintenance procedures with and without milling materials

Directory of Open Access Journals (Sweden)

Rafiqul A. Tarefder

2016-01-01

Full Text Available This study evaluates maintenance treatment followed by different Districts of New Mexico Department of Transportation (NMDOT. In addition, two case studies on the use of old pavement materials, called the “millings”, in maintenance projects are reported. Based on this study, it is observed that none of the Districts have a written procedure for maintenance work. Rather Districts rely on the experience of the maintenance crew for conducting maintenance projects. All Districts prefer to use chip seal for maintenance irrespective of distress conditions of the pavements. Patching and crack sealing are usually done before chip sealing to extend the life of the chip seals. Sand seal, scrub seal, and slurry seal projects are not done by District maintenance crews but by outside contractors. It is also observed that all Districts are interested in using millings in maintenance projects and most have already used millings in at least one maintenance project with some success and failure. Most of the Districts have used coarse fraction of millings in chip seal projects successfully. However, they failed to find a proper way to process the fine fractions of millings. Case Study I shows that fine millings can be used to construct thin overlay when mixed with emulsion in pug mill or hot drums. Case Study II concludes that fine millings can be used as fine/sand seal successfully following the same procedure and using the same equipment as chip seal. Keywords: Millings, Maintenance, Emulsion, Rutting, Pug-mill

Indian Americans at Mille Lacs.

Science.gov (United States)

Holbert, Victoria L.; And Others

The Training Center for Community Programs prepared a report on the Mille Lacs (Chippewa) Reservation in Minnesota. Data for the report were from 2 separate sources: a survey conducted by the Training Center with the assistance of the Mille Lacs community action program (1967) and an attitudinal survey conducted by Victoria Holbert during 1969.…

Ground beetle populations near a kraft mill

Energy Technology Data Exchange (ETDEWEB)

Freitag, R.; Hastings, L.; Mercer, W.R.; Smith, A.

1973-02-01

Twenty species of ground beetles (Family Carabidae) and one species of carrion beetle (Family Silphidae) were collected in six stations east of a kraft paper mill in Thunder Bay, Ontario, from May to August, 1971. The beetle population decreased markedly towards the mill. There was no apparent statistical difference in size variation of specimens near the mill and those further away.

21 CFR 515.10 - Medicated feed mill license applications.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Medicated feed mill license applications. 515.10... (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Applications § 515.10 Medicated feed mill license applications. (a) Medicated feed mill license applications (Forms FDA 3448) may...

Uranium Mill Tailings Remedial Action Project, fiscal year 1995 annual report to stakeholders

International Nuclear Information System (INIS)

1995-01-01

In 1978, Congress authorized the DOE to assess and clean up contamination at 24 designated former uranium processing sites. The DOE is also responsible for cleaning up properties in the vicinity of the sites where wind and water erosion deposited tailings or people removed them from the site for use in construction or landscaping projects. Cleanup is being undertaken in cooperation with state governments and Indian tribes within whose boundaries the sites are located. It is being conducted in two phases: the surface project and the ground water project. This report addresses specifics about both phases of the UMTRA Project. DOE's UMTRA Project is the world's largest materials management project ever undertaken to reduce or eliminate risk to the general public from exposure to potentially hazardous and radioactive materials. With an estimated cost at completion of nearly $2 billion for both phases of the UMTRA Project, and with the responsibility for encapsulating and isolating almost one-fourth of all the uranium mill tailings generated across the entire US (more than 44 million cubic yards), the UMTRA Project and its people have achieved a long record of safely and effectively completing its mission. It continually enhances its national reputation through its diligent process and cost efficiency as well as its international recognition for its technological innovation

High-energy ball milling of powder B-C mixtures

International Nuclear Information System (INIS)

Ramos, Alfeu S.; Taguchi, Simone P.; Ramos, Erika C.T.; Arantes, Vera L.; Ribeiro, Sebastiao

2006-01-01

The present work reports on the preparation of B-10 at.% C and B-18 at.% C powders by high-energy ball milling and further heat treatment. The milling process was carried out in a planetary ball mill. Following the milling process, powder samples were heat-treated at 1200 deg. C for 4 h using inert atmosphere. The milled and heat-treated B-10C and B-18C powders were characterized by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. A reduction on the intensity of B and C peaks was noticed after milling for 2 h, probably due the fine powder particle sizes because the pronounced fracture mechanism during ball milling of brittle starting components. The XRD patterns of B-10C and B-18C powders milled for 6 h indicated the presence of other peaks, suggesting that a metastable structure could have been formed. After milling for 90 h, these unknown peaks were still present. A large amount of B 4 C was formed after heat treatment at 1200 deg. C for 4 h beside these unknown peaks

The yang mills gravity dual

International Nuclear Information System (INIS)

Crooks, David E.; Evans, Nick

2003-01-01

We describe a ten dimensional supergravity geometry which is dual to a gauge theory that is non-supersymmetric Yang Mills in the infra-red but reverts to N=4 super Yang Mills in the ultra-violet. A brane probe of the geometry shows that the scalar potential of the gauge theory is stable. We discuss the infra-red behaviour of the solution. The geometry describes a Schroedinger equation potential that determines the glueball spectrum of the theory; there is a mass gap and a discrete spectrum. The glueball mass predictions match previous AdS/CFT Correspondence computations in the non-supersymmetric Yang Mills theory, and lattice data, at the 10% level. (author)

Simulation of Vibrations in Real Time Plane Milling with Spindle Speed Correction

Directory of Open Access Journals (Sweden)

I. I. Ivanov

2017-01-01

Full Text Available In milling the hard-to-machine materials vibrations (chatter often arise from the high cutting forces if a technological system is insufficiently rigid.The main way to suppress these vibrations is to increase a stiffness of the mounting system of the tool and the work-piece to be machined. However, sometimes this method doesn’t lead to desirable result because of high values of intrinsic pliability of the tool and the work-piece. Currently, there are more complicated methods to ensure milling process quality. Among them there are three main groups:mathematical simulation of milling process dynamics and computation of processing parameters which provide high quality of machined surface, low level of vibrations and static deflections of a tool and a work-piece;introduction of the active vibration suppression devices into machine tool design; such devices include a vibration sensor, a feedback circuit, and an actuator which induces kinematic or force action on the oscillatory system;control of processing parameters, mainly of rotation frequency for minimizing the amplitudes of vibrations.The paper studies one of the 3rd group methods. There is a suggestion to process a signal of vibrational accelerations in real time and detect a chatter onset. If the chatter has been detected its frequency is to be identified, and the new value of rotation speed is set:where Ω – rotation frequency, rot/s; p – the tool eigenfrequency value identified during processing, Hz; z – mill tooth number; i – positive integer number; ε<1 – small positive parameter. In the current research it is assumed that ε = 0,2.The formula has been chosen because at the rotation frequency axis where tooth pass frequency is slightly less than the eigenfrequency divided by the integer value there are stable zones of dynamics in the milling process.The study shows a developed model of the plane milling dynamics. It includes a dynamic model of the tool, a model of cutting

LONG-TERM DEMONSTRATION OF SORBENT ENHANCEMENT ADDITIVE TECHNOLOGY FOR MERCURY CONTROL

Energy Technology Data Exchange (ETDEWEB)

Jason D. Laumb; Dennis L. Laudal; Grant E. Dunham; John P. Kay; Christopher L. Martin; Jeffrey S. Thompson; Nicholas B. Lentz; Alexander Azenkeng; Kevin C. Galbreath; Lucinda L. Hamre

2011-05-27

Long-term demonstration tests of advanced sorbent enhancement additive (SEA) technologies have been completed at five coal-fired power plants. The targeted removal rate was 90% from baseline conditions at all five stations. The plants included Hawthorn Unit 5, Mill Creek Unit 4, San Miguel Unit 1, Centralia Unit 2, and Hoot Lake Unit 2. The materials tested included powdered activated carbon, treated carbon, scrubber additives, and SEAs. In only one case (San Miguel) was >90% removal not attainable. The reemission of mercury from the scrubber at this facility prevented >90% capture.

Treatment technologies of liquid and solid wastes from two-phase olive oil mills

OpenAIRE

Borja Padilla, Rafael; Raposo Bejines, Francisco; Rincón, Bárbara

2006-01-01

Over the last 10 years the manufacture of olive oil has undergone important evolutionary changes in the equipment used for the separation of olive oil from the remaining components. The latest development has been the introduction of a two-phase centrifugation process in which a horizontally-mounted centrifuge is used for a primary separation of the olive oil fraction from the vegetable solid material and vegetation water. Therefore, the new two-phase olive oil mills produce three ident...

Treatment technologies of liquid and solid wastes from two-phase olive oil mills

OpenAIRE

Rincón, Bárbara; Raposo, Francisco; Borja, Rafael

2006-01-01

Over the last 10 years the manufacture of olive oil has undergone important evolutionary changes in the equipment used for the separation of olive oil from the remaining components. The latest development has been the introduction of a two-phase centrifugation process in which a horizontally-mounted centrifuge is used for a primary separation of the olive oil fraction from the vegetable solid material and vegetation water. Therefore, the new two-phase olive oil mills produce three identifiabl...

Reactive-inspired ball-milling synthesis of an ODS steel: study of the influence of ball-milling and annealing

International Nuclear Information System (INIS)

Brocq, M.

2010-10-01

In the context of the development of new ODS (Oxide Dispersion Strengthened) steels as core materials in future nuclear reactors, we investigated a new process inspired by reactive ball-milling which consists in using YFe 3 andFe 2 O 3 as starting reactants instead of Y 2 O 3 to produce a dispersion of nano-oxides in a steel matrix and the influence of synthesis conditions on the nano-oxide characteristics were studied. For that aim, ODS steels were prepared by ball-milling and then annealed. Multi-scale characterizations were performed after each synthesis step, using notably atom probe tomography and small angle neutron scattering. The process inspired by reactive ball-milling was shown to be efficient for ODS steel synthesis, but it does not modify the nano-oxide characteristics as compared to those of oxides directly incorporated in the matrix by ball-milling. Broadly speaking, the nature of the starting oxygen bearing reactants has no influence on nano-oxide formation. Moreover, we showed that the nucleation of nano-oxides nucleation can start during milling and continues during annealing with a very fast kinetic. The final characteristics of nano-oxides formed in this way can be monitored through ball-milling parameters (intensity, temperature and atmosphere) and annealing parameters (duration and temperature). (author)

Yangian Symmetry of Scattering Amplitudes and the Dilatation Operator in N=4 Supersymmetric Yang-Mills Theory.

Science.gov (United States)

Brandhuber, Andreas; Heslop, Paul; Travaglini, Gabriele; Young, Donovan

2015-10-02

It is known that the Yangian of PSU(2,2|4) is a symmetry of the tree-level S matrix of N=4 super Yang-Mills theory. On the other hand, the complete one-loop dilatation operator in the same theory commutes with the level-one Yangian generators only up to certain boundary terms found by Dolan, Nappi, and Witten. Using a result by Zwiebel, we show how the Yangian symmetry of the tree-level S matrix of N=4 super Yang-Mills theory implies precisely the Yangian invariance, up to boundary terms, of the one-loop dilatation operator.

Critical management issues for the Uranium Mill Tailings Remedial Action (UMTRA) Project

International Nuclear Information System (INIS)

Themelis, J.G.; Krishnan, K.R.

1985-01-01

The Uranium Mill Tailings Radiation Control Act of 1978 (PL95-604) authorized the Secretary of Energy to enter into cooperative agreements with certain states and Indian Tribes to clean up 24 inactive uranium mill tailing sites and associated vicinity properties. The Uranium Mill Tailings Remedial Action (UMTRA) Project includes the three Federal agencies (EPA, DOE, and NRC), eleven state, Indian Tribes, and at least four major contractors. The UMTRA Project extends over a period of ten years. The standards for the Project require a design life of 1000 years with a minimum performance period of 200 years. This paper discusses the critical management issues in dealing with the UMTRA Project and identifies the development of solutions for many of those issues. The highlights to date are promulgation of EPA standards, continued support from Congress and participating states and Indian Tribes, significant leadership shown at all levels, establishment of credibility with the public, and continued motivation of the team. The challenge for tomorrow is making certain NRC will license the sites and maintaining the high level of coordination exhibited to date to assure Project completion on schedule

Uranium mill tailings remedial action project real estate management plan

International Nuclear Information System (INIS)

1994-09-01

This plan summarizes the real estate requirements of the US Department of Energy's (DOE) Uranium Mill Tailings Action (UMTRA) Project, identifies the roles and responsibilities of project participants involved in real estate activities, and describes the approaches used for completing these requirements. This document is intended to serve as a practical guide for all project participants. It is intended to be consistent with all formal agreements, but if a conflict is identified, the formal agreements will take precedence

Uranium mill tailings remedial action project real estate management plan

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

This plan summarizes the real estate requirements of the US Department of Energy`s (DOE) Uranium Mill Tailings Action (UMTRA) Project, identifies the roles and responsibilities of project participants involved in real estate activities, and describes the approaches used for completing these requirements. This document is intended to serve as a practical guide for all project participants. It is intended to be consistent with all formal agreements, but if a conflict is identified, the formal agreements will take precedence.

Uranium mill tailings

International Nuclear Information System (INIS)

McLaren, L.H.

1982-11-01

This bibliography contains information on uranium mill tailings included in the Department of Energy's Energy Data Base from January 1981 through October 1982. The abstracts are grouped by subject category as shown in the table of contents. Entries in the subject index also facilitate access by subject, e.g., Mill Tailings/Radiation Hazards. Within each category the arrangement is by report number for reports, followed by nonreports in reverse chronological order. These citations are to research reports, journal articles, books, patents, theses, and conference papers from worldwide sources. Five indexes, each preceded by a brief description, are provided: Corporate Author, Personal Author, Subject, Contract Number, and Report Number. (335 abstracts)

Geometrical characterization of micro end milling tools

DEFF Research Database (Denmark)

Borsetto, Francesca; Bariani, Paolo; Bissacco, Giuliano

2005-01-01

Performance of the milling process is directly affected by the accuracy of tool geometry. Development of methods suitable for dimensional characterization of such tools, with low measurement uncertainties is therefore of relevance. The present article focuses on the geometrical characterization...... of a flat micro end milling tool with a nominal mill diameter of 200 microns. An experimental investigation was carried out involving two different non-contact systems...

An extended topological Yang-Mills theory

International Nuclear Information System (INIS)

Deguchi, Shinichi

1992-01-01

Introducing infinite number of fields, we construct an extended version of the topological Yang-Mills theory. The properties of the extended topological Yang-Mills theory (ETYMT) are discussed from standpoint of the covariant canonical quantization. It is shown that the ETYMT becomes a cohomological topological field theory or a theory equivalent to a quantum Yang-Mills theory with anti-self-dual constraint according to subsidiary conditions imposed on state-vector space. On the basis of the ETYMT, we may understand a transition from an unbroken phase to a physical phase (broken phase). (author)

Contamination risk of stable isotope samples during milling.

Science.gov (United States)

Isaac-Renton, M; Schneider, L; Treydte, K

2016-07-15

Isotope analysis of wood is an important tool in dendrochronology and ecophysiology. Prior to mass spectrometry analysis, wood must be homogenized, and a convenient method involves a ball mill capable of milling samples directly in sample tubes. However, sample-tube plastic can contaminate wood during milling, which could lead to biological misinterpretations. We tested possible contamination of whole wood and cellulose samples during ball-mill homogenization for carbon and oxygen isotope measurements. We used a multi-factorial design with two/three steel milling balls, two sample amounts (10 mg, 40 mg), and two milling times (5 min, 10 min). We further analyzed abrasion by milling empty tubes, and measured the isotope ratios of pure contaminants. A strong risk exists for carbon isotope bias through plastic contamination: the δ(13) C value of polypropylene deviated from the control by -6.77‰. Small fibers from PTFE filter bags used during cellulose extraction also present a risk as the δ(13) C value of this plastic deviated by -5.02‰. Low sample amounts (10 mg) showed highest contamination due to increased abrasion during milling (-1.34‰), which is further concentrated by cellulose extraction (-3.38‰). Oxygen isotope measurements were unaffected. A ball mill can be used to homogenize samples within test tubes prior to oxygen isotope analysis, but not prior to carbon or radiocarbon isotope analysis. There is still a need for a fast, simple and contamination-free sample preparation procedure. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Microstructure-sensitive flow stress modeling for force prediction in laser assisted milling of Inconel 718

Directory of Open Access Journals (Sweden)

Pan Zhipeng

2017-01-01

Full Text Available Inconel 718 is a typical hard-to-machine material that requires thermally enhanced machining technology such as laser-assisted milling. Based upon finite element analysis, this study simulates the forces in the laser-assisted milling process of Inconel 718 considering the effects of grain growth due to γ' and γ" phases. The γ" phase is unstable and becomes the δ phase, which is likely to precipitate at a temperature over 750 °C. The temperature around the center of spot in the experiments is 850 °C, so the phase transformation and grain growth happen throughout the milling process. In the analysis, this study includes the microstructure evolution while accounting for the effects of dynamic recrystallization and grain growth through the Avrami model. The grain growth reduces the yield stress and flow stress, which improves the machinability. In finite element analysis (FEA, several boundary conditions of temperature varying with time are defined to simulate the movement of laser spot, and the constitutive model is described by Johnson-Cook equation. In experiments, this study collects three sets of cutting forces and finds that the predicted values are in close agreements with measurements especially in feed direction, in which the smallest error is around 5%. In another three simulations, this study also examines the effect of laser preheating on the cutting forces by comparison with a traditional milling process without laser assist. When the laser is off, the forces increase in all cases, which prove the softening effect of laser-assisted milling. In addition, when the axial depth of milling increases, the laser has a more significant influence, especially in axial direction, in which the force with laser is more than 18% smaller than the one without laser. Overall, this study validates the influence of laser-assisted milling on Inconel 718 by predicting the cutting forces in FEA.

National/international R and D programs on uranium mill tailings

International Nuclear Information System (INIS)

Hamel, P.E.

1981-05-01

The mining and milling of uranium ores results in the production of large quantities of wastes containing low concentrations of radionuclides such as uranium, thorium, radium, radon and their daughter products. The current concern of the regulatory authorities is with the extent of the problems and the disposal methods that must be required now to ensure that an acceptable level of protection is maintained in the long term. This concern is the subject of a number of R and D programs. In Canada, the Technical Planning Group on Uranium Tailings was established to review ongoing activities and to plan a research program on the management of wastes after the mine and mill have shut down. The Group has completed its review and a report containing its conclusions and recommendations for a proposed national R and D program has been prepared. Included is a proposal for a centralized organizational structure for the coordination and managment of the total program which is to be supported jointly by the federal government, two (Ontario, Saskatchewan) provincial governments, and uranium producers. At the international level, the Nuclear Energy Agency originated, in 1979, a program to study the extent of the long-term problems of uranium mill tailings, and to develop an internationally acceptable methodology for making rational decisions regarding their long-term management taking into account the ICRP principles and system of dose limitation

Uranium Mill Tailings Remedial Action Program. Annual status report

International Nuclear Information System (INIS)

1984-12-01

The Uranium Mill Tailings Remedial Action (UMTRA) Project FY 1984 major accomplishments are summarized. Twenty-five percent of the processing site remedial actions at Canonsburg, PA, were completed. Remedial action on 118 vicinity properties at four designated locations were initiated and survey and inclusion activities on a total of 420 vicinity properties were completed. The Environmental Impact Statement (EIS) for Salt Lake City, UT, and the Environmental Assessment (EA) for Shiprock, NM were published, and the preliminary draft EIS for Durango, CO, was prepared. Remedial Action Plans (RAPs) for Salt Lake City, UT, and Shiprock, NM were completed, and draft RAPs for Gunnison, CO, and Riverton, WY were prepared. Cooperative agreements with Oregon, Wyoming, and South Dakota were executed, and the Utah cooperative agreement was modified to assign the construction management responsibility to the state. An Interagency Agreement with TVA for disposal of the Edgemont vicinity property material was executed

Hydrogen storage thermodynamics and kinetics of LaMg11Ni + x wt.% Ni (x = 100, 200) alloys synthesized by mechanical milling

International Nuclear Information System (INIS)

Zhang, Yanghuan; Jia, Zhichao; Central Iron and Steel Research Institute, Beijing; Yuan, Zeming; Qi, Yan; Zhao, Dongliang; Hou, Zhonghui

2016-01-01

LaMg 11 Ni + x wt.% Ni (x = 100, 200) composite hydrogen storage alloys with a nanocrystalline/amorphous structure were synthesized using ball milling technology. The effects of Ni content and milling time on hydrogen storage thermodynamics and dynamics of the alloys were investigated systematically. The hydrogen desorption properties were assessed using a Sieverts apparatus and differential scanning calorimetry. The thermodynamic parameters for the hydrogen absorption and desorption were calculated using the Van't Hoff equation. The hydrogen desorption activation energies of the hydrogenated alloys were also estimated by Arrhenius and Kissinger methods. Results indicate that the amount of Ni added has no effect on the thermodynamics of the alloys, but it significantly improves their absorption and desorption kinetics. Furthermore, the milling time has a great influence on the hydrogen storage properties. To be specific, the hydrogen absorption capacities reach the maximum values with the variation of milling time, and the hydrogen desorption activation energy obviously decreases with increasing milling time.

Minimization of energy and surface roughness of the products machined by milling

Science.gov (United States)

Belloufi, A.; Abdelkrim, M.; Bouakba, M.; Rezgui, I.

2017-08-01

Metal cutting represents a large portion in the manufacturing industries, which makes this process the largest consumer of energy. Energy consumption is an indirect source of carbon footprint, we know that CO2 emissions come from the production of energy. Therefore high energy consumption requires a large production, which leads to high cost and a large amount of CO2 emissions. At this day, a lot of researches done on the Metal cutting, but the environmental problems of the processes are rarely discussed. The right selection of cutting parameters is an effective method to reduce energy consumption because of the direct relationship between energy consumption and cutting parameters in machining processes. Therefore, one of the objectives of this research is to propose an optimization strategy suitable for machining processes (milling) to achieve the optimum cutting conditions based on the criterion of the energy consumed during the milling. In this paper the problem of energy consumed in milling is solved by an optimization method chosen. The optimization is done according to the different requirements in the process of roughing and finishing under various technological constraints.

Self-dual solutions to Euclidean Yang-Mills equations

International Nuclear Information System (INIS)

Corrigan, E.

1979-01-01

The paper provides an introduction to two approaches towards understanding the classical Yang-Mills field equations. On the one hand, the work of Atiyah and Ward showed that the self-dual equations, which are non-linear, could be regarded as a set of linear equations which turned out to be related to each other by Baecklund transformations. Fundamental to their procedure was the observation that the information carried by the vector potential could be coded into the structure of certain analytic vector bundles over a three dimensional projective space. The classification of these bundles and the subsequent recovery of the gauge field led to the infinite set of ansaetze, corresponding to the sets of linear equation mentioned already. On the other hand, Atiyah, Hitchin, Drinfeld and Manin have recently constructed, completely algebraically, the bundles of interest and indicated how the Yang-Mills potential may be obtained. Remarkably, their construction differs very little as the gauge group is changed (to any of the classical compact groups) and, uses only the elementary operations of linear algebra to yield potentials as rational functions of the spatial coordinates. (Auth.)

Monticello Mill Tailings Site, Operable Unit lll, Annual Groundwater Report, May 2015 Through April 2016

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Jason [USDOE Office of Legacy Management (LM), Washington, DC (United States); Smith, Fred [Navarro Research and Engineering, Oak Ridge, TN (United States)

2016-10-01

This report provides the annual analysis of water quality restoration progress, cumulative through April 2016, for Operable Unit (OU) III, surface water and groundwater, of the U.S. Department of Energy (DOE) Office of Legacy Management (LM) Monticello Mill Tailings Site (MMTS). The MMTS is a Comprehensive Environmental Response, Compensation, and Liability Act National Priorities List site located in and near the city of Monticello, San Juan County, Utah. MMTS comprises the 110-acre site of a former uranium- and vanadium-ore-processing mill (mill site) and 1700 acres of surrounding private and municipal property. Milling operations generated 2.5 million cubic yards of waste (tailings) from 1942 to 1960. The tailings were impounded at four locations on the mill site. Inorganic constituents in the tailings drained from the impoundments to contaminate local surface water (Montezuma Creek) and groundwater in the underlying alluvial aquifer. Mill tailings dispersed by wind and water also contaminated properties surrounding and downstream of the mill site. Remedial actions to remove and isolate radiologically contaminated soil, sediment, and debris from the former mill site, Operable Unit I (OU I), and surrounding properties (OU II) were completed in 1999 with the encapsulation of the wastes in an engineered repository located on DOE property 1 mile south of the former mill site. This effectively removed the primary source of groundwater contamination; however, contamination of groundwater and surface water remains within OU III at levels that exceed water quality protection standards. Uranium is the primary contaminant of concern (COC). LM implemented monitored natural attenuation with institutional controls as the OU III remedy in 2004. Because groundwater restoration proceeded more slowly than expected and did not meet performance criteria established in the OU III Record of Decision (June 2004), LM implemented a contingency action in 2009 by an Explanation of

The Influence of Milling and Spark Plasma Sintering on the Microstructure and Properties of the Al7075 Alloy

Science.gov (United States)

Málek, Přemysl; Minárik, Peter; Novák, Pavel; Průša, Filip

2018-01-01

The compact samples of an Al7075 alloy were prepared by a combination of gas atomization, high energy milling, and spark plasma sintering. The predominantly cellular morphology observed in gas atomized powder particles was completely changed by mechanical milling. The continuous-like intermetallic phases present along intercellular boundaries were destroyed; nevertheless, a small amount of Mg(Zn,Cu,Al)2 phase was observed also in the milled powder. Milling resulted in a severe plastic deformation of the material and led to a reduction of grain size from several µm into the nanocrystalline region. The combination of these microstructural characteristics resulted in abnormally high microhardness values exceeding 300 HV. Consolidation through spark plasma sintering (SPS) resulted in bulk samples with negligible porosity. The heat exposition during SPS led to precipitation of intermetallic phases from the non-equilibrium microstructure of both gas atomized and milled powders. SPS of the milled powder resulted in a recrystallization of the severely deformed structure. An ultra-fine grained structure (grain size close to 500 nm) with grains divided primarily by high-angle boundaries was formed. A simultaneous release of stored deformation energy and an increase in the grain size caused a drop of microhardness to values close to 150 HV. This value was retained even after annealing at 425 °C. PMID:29614046

The Influence of Milling and Spark Plasma Sintering on the Microstructure and Properties of the Al7075 Alloy

Directory of Open Access Journals (Sweden)

Orsolya Molnárová

2018-04-01

Full Text Available The compact samples of an Al7075 alloy were prepared by a combination of gas atomization, high energy milling, and spark plasma sintering. The predominantly cellular morphology observed in gas atomized powder particles was completely changed by mechanical milling. The continuous-like intermetallic phases present along intercellular boundaries were destroyed; nevertheless, a small amount of Mg(Zn,Cu,Al2 phase was observed also in the milled powder. Milling resulted in a severe plastic deformation of the material and led to a reduction of grain size from several µm into the nanocrystalline region. The combination of these microstructural characteristics resulted in abnormally high microhardness values exceeding 300 HV. Consolidation through spark plasma sintering (SPS resulted in bulk samples with negligible porosity. The heat exposition during SPS led to precipitation of intermetallic phases from the non-equilibrium microstructure of both gas atomized and milled powders. SPS of the milled powder resulted in a recrystallization of the severely deformed structure. An ultra-fine grained structure (grain size close to 500 nm with grains divided primarily by high-angle boundaries was formed. A simultaneous release of stored deformation energy and an increase in the grain size caused a drop of microhardness to values close to 150 HV. This value was retained even after annealing at 425 °C.

The influence of parent concrete and milling intensity on the properties of recycled aggregates

NARCIS (Netherlands)

Lotfi, Somayeh; Rem, P.C.; Deja, J; Mroz, R; Di Maio, F.; Lotfi, S.; Bakker, M.; Hu, M.; Vahidi, A.

2017-01-01

The C2CA concrete recycling process consists of a combination of smart demolition, gentle grinding of the crushed concrete in an autogenous mill, and a novel dry classification technology called ADR to remove the fines. The` main factors in the C2CA process which influence the properties of Recycled

78 FR 31315 - Kraft Pulp Mills NSPS Review

Science.gov (United States)

2013-05-23

... Kraft Pulp Mills NSPS Review; Proposed Rule #0;#0;Federal Register / Vol. 78 , No. 100 / Thursday, May...-OAR-2012-0640; FRL-9815-9] RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection... performance standards for kraft pulp mills. These revised standards include particulate matter emission limits...

Improved oral bioavailability of probucol by dry media-milling.

Science.gov (United States)

Li, Jia; Yang, Yan; Zhao, Meihui; Xu, Hui; Ma, Junyuan; Wang, Shaoning

2017-09-01

The polymer/probucol co-milled mixtures were prepared to improve drug dissolution rate and oral bioavailability. Probucol, a BCS II drug, was co-milled together with Copovidone (Kollidon VA64, VA64), Soluplus, or MCC using the dry media-milling process with planetary ball-milling equipment. The properties of the milled mixtures including morphology, crystal form, vitro drug dissolution and in vivo oral bioavailability in rats were evaluated. Probucol existed as an amorphous in the matrix of the co-milled mixtures containing VA64, which helped to enhance drug dissolution. The ternary mixture composed of VA64, RH40, and probucol showed increased dissolution rates in both sink and non-sink conditions. It also had a higher oral bioavailability compared to the reference formulation. Dry-media milling of binary or ternary mixtures composed of drug, polymer and surfactant possibly have wide applications to improve dissolution rate and oral bioavailability of water-insoluble drugs. Copyright © 2017 Elsevier B.V. All rights reserved.

PENGARUH TEKNIK PENYAYATAN PAHAT MILLING PADA CNC MILLING 3 AXIS TERHADAP TINGKAT KEKASARAN PERMUKAAN BENDA BERKONTUR

Directory of Open Access Journals (Sweden)

Irawan Irawan

2016-06-01

Full Text Available Dalam perindustrian penggunaan mesin CNC Milling sangat di andalkan untuk mendapatkan hasil yang optimum baik secara kualitas maupun kuantitas. Akan tetapi muncul permasalahan,bagaimana pengaruh perbedaan teknik penyayatan terhadap nilai kekasaran permukaan benda kerja berkontur dalam proses milling CNC. Penelitian ini bertujuan untuk mengetahui pengaruh metode penyayatan pahat milling terhadap kekasaran permukaan benda kerja berkontur yang di hasilkan pada proses freis dengan menggunakan mesin milling CNC - 3Axis Makino S33. Peneliitan ini merancang dan membuat molding Cover stop kontak dikarenakan permukaan produk cover stop kontak memiliki permukaan yang berkontur. Molding ini terdiri dari Core dan Cavity. Benda kerja yang akan di ujicoba adalah bagian Core sebanyak 3 buah. Dalam pengerjaanya benda ujicoba diberikan perlakuan yang sama antara lain, kedalaman pemotongan, kecepatan spindle, dan jenis pahat yang di gunakan, kemudian dari ke 3 benda kerja tersebut masing- masing di tentukan 3 titik pengukuran. Dari hasil pengujian yang di peroleh kemudian dilakukan analisis tabel. Nilai kekasaran permukaan terendah (rata-rata kekasaran 0.899µ m dengan waktu permesinan tercepat (waktu proses 1 jam 08 menit pada penggunaan metode penyayatan 3D offset finishing. Penulis menyarankan agar dalam proses freis menggunakan mesin milling CNC 3Axis Makino S33 pada permukaan benda yang berkontur, untuk mendapatkan nilai kekasaran yang terendah disarankan menggunakan metode penyayatan 3D offset finishing.

BRST cohomology of N = 2 super-Yang-Mills theory in four dimensions

International Nuclear Information System (INIS)

Tanzini, A.; Ventura, O.S.; Vilar, L.C.Q.; Sorella, S.P.

2000-01-01

The BRST cohomology of the N = 2 supersymmetric Yang-Mills theory in four dimensions is discussed by making use of the twisted version of the N = 2 algebra. By the introduction of a set of suitable constant ghosts associated with the generators of N = 2, the quantization of the model can be done by taking into account both gauge invariance and supersymmetry. In particular, we show how the twisted N = 2 algebra can be used to obtain in a straightforward way the relevant cohomology classes. Moreover, we shall be able to establish a very useful relationship between the local gauge-invariant polynomial tr φ 2 and the complete N = 2 Yang-Mills action. This important relation can be considered as the first step towards a fully algebraic proof of the one-loop exactness of the N = 2 β-function.

Towards a manifestly gauge invariant and universal calculus for Jang-Mills theory

International Nuclear Information System (INIS)

Arnone, S.; Gatti, A.; Morris, T.R.

2002-01-01

A manifestly gauge invariant exact renormalization group for pure SU (N) Jang-Mills theory is proposed, along with the necessary gauge invariant regularisation which implements the effective cutoff. The latter is naturally incorporated by embedding the theory into a spontaneously broken SU(N/N) super-gauge theory, which guarantees finiteness to all orders in perturbation theory. The effective action, from which one extracts the physics, can be computed whilst manifestly preserving gauge invariance at each and every step. As an example, we give an elegant computation of the one-loop SU(N) Jang-Mills beta function, for the first time at finite N without any gauge fixing or ghosts. It is also completely independent of the details put in by hand, e.g. the choice of covariantisation and the cutoff profile, and, therefore, guides us to a procedure for streamlined calculations (Authors)

Model Predictive Control for an Industrial SAG Mill

DEFF Research Database (Denmark)

Ohan, Valeriu; Steinke, Florian; Metzger, Michael

2012-01-01

identication. When applied to MIMO systems we call this controller a MIMO-ARX based MPC. We use an industrial Semi-Autogenous Grinding (SAG) mill to illustrate the performance of this controller. SAG mills are the primary units in a grinding chain and also the most power consuming units. Therefore, improved...... control of SAG mills has the potential to signicantly improve eciency and reduce the specic energy consumption for mineral processes. Grinding circuits involving SAG mills are multivariate processes. Commissioning of a control system based on a classical single-loop controllers with logic is time...

Spinors in self-dual Yang-Mills fields in minkowski space

International Nuclear Information System (INIS)

Pervushin, V.N.

1981-01-01

Yang-Mills theory with infrared divergences removed by spontaneous vacuum symmetry breaking is considered. The corresponding vacuum fields are self-dual and are defined in the Minkowski space. The complete set of solutions of Dirac equations with self-dual fields, depending on certain arbitrary function, is found. Physical observables (charge, energy, spin) for the spinor fields within the self-dual vacuum are calculated and a Hermitean Hamiltonian is obtained. The physical picture corresponds to a relativistic generalization of the hadron bag model [ru

7 CFR 868.301 - Definition of milled rice.

Science.gov (United States)

2010-01-01

... 7 Agriculture 7 2010-01-01 2010-01-01 false Definition of milled rice. 868.301 Section 868.301... FOR CERTAIN AGRICULTURAL COMMODITIES United States Standards for Milled Rice Terms Defined § 868.301 Definition of milled rice. Whole or broken kernels of rice (Oryza sativa L.) from which the hulls and at...

Preliminary evaluation of uranium mill tailings conditioning as an alternative remedial action technology

International Nuclear Information System (INIS)

Dreesen, D.R.; Cokal, E.J.; Thode, E.F.; Wangen, L.E.; Williams, J.M.

1981-01-01

Conditioning of uranium mill tailings is being investigated as an alternative remedial action for inactive tailings piles to be stabilized by the US Department of Energy. Tailings from high priority sites have been characterized for elemental composition, mineralogy, aqueous leachable contaminants, and radon emanation power to provide a baseline to determine the environmental hazard control produced by conditioning. Thermal stabilization of tailings at high temperatures and removal of contaminants by sulfuric acid leaching are being investigated for technical merit as well as economic and engineering feasibility

Ethical Considerations in Technology Transfer.

Science.gov (United States)

Froehlich, Thomas J.

1991-01-01

Examines ethical considerations involved in the transfer of appropriate information technology to less developed countries. Approaches to technology are considered; two philosophical frameworks for studying ethical considerations are discussed, i.e., the Kantian approach and the utilitarian perspective by John Stuart Mill; and integration of the…

Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al₂O₃ Nanocomposite Synthesized by Ball Milling and Powder Metallurgy.

Science.gov (United States)

Toozandehjani, Meysam; Matori, Khamirul Amin; Ostovan, Farhad; Abdul Aziz, Sidek; Mamat, Md Shuhazlly

2017-10-26

The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al₂O₃ (Al-5Al₂O₃) has been investigated. Al-5Al₂O₃ nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al₂O₃ nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD) analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness ( HV ), nano-hardness ( HN ), and Young's modulus ( E ) of Al-5Al₂O₃ nanocomposites. HV , HN , and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively.

Fault Detection in Coal Mills used in Power Plants

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, Babak

2006-01-01

In order to achieve high performance and efficiency of coal-fired power plants, it is highly important to control the coal flow into the furnace in the power plant. This means suppression of disturbances and force the coal mill to deliver the required coal flow, as well as monitor the coal mill...... in order to detect faults in the coal mill when they emerge. This paper deals with the second objective. Based on a simple dynamic model of the energy balance a residual is formed for the coal mill. An optimal unknown input observer is designed to estimate this residual. The estimated residual is following...... tested on measured data of a fault in a coal mill, it can hereby be concluded that this residual is very useful for detecting faults in the coal mill....

Analytical Prediction of Three Dimensional Chatter Stability in Milling

Science.gov (United States)

Altintas, Yusuf

The chip regeneration mechanism during chatter is influenced by vibrations in three directions when milling cutters with ball end, bull nose, or inclined cutting edges are used. A three dimensional chatter stability is modeled analytically in this article. The dynamic milling system is formulated as a function of cutter geometry, the frequency response of the machine tool structure at the cutting zone in three Cartesian directions, cutter engagement conditions and material property. The dynamic milling system with nonlinearities and periodic delayed differential equations is reduced to a three dimensional linear stability problem by approximations based on the physics of milling. The chatter stability lobes are predicted in the frequency domain using the proposed analytical solution, and verified experimentally in milling a Titanium alloy with a face milling cutter having circular inserts.

STUDY OF CHIP IGNITION AND CHIP MORPHOLOGY AFTER MILLING OF MAGNESIUM ALLOYS

Directory of Open Access Journals (Sweden)

Ireneusz Zagórski

2016-12-01

Full Text Available The paper analyses the impact of specified technological parameters of milling (vc, fz, ap on time to ignition. Stages leading to chip ignition were analysed. Metallographic images of magnesium chip were presented. No significant difference was observed in time to ignition in different chip fractions. Moreover, the surface of chips was free of products of ignition and signs of strong oxidation.

Digital workflow for virtually designing and milling ceramic lithium disilicate veneers: a clinical report.

Science.gov (United States)

Zandinejad, A; Lin, W S; Atarodi, M; Abdel-Azim, T; Metz, M J; Morton, D

2015-01-01

Laminate veneers have been routinely used to restore and enhance the appearance of natural dentition. The traditional pathway for fabricating veneers consisted of making conventional polyvinyl siloxane impressions, producing stone casts, and fabricating final porcelain prostheses on stone dies. Pressed ceramics have successfully been used for laminate veneer fabrication for several years. Recently, digital computer-aided design/computer-aided manufacturing scanning has become commercially available to make a digital impression that is sent electronically to a dental laboratory or a chairside milling machine. However, technology has been developed to allow digital data acquisition in conjunction with electronically transmitted data that enables virtual design of restorations and milling at a remote production center. Following the aforementioned workflow will provide the opportunity to fabricate a physical cast-free restoration. This new technique has been reported recently for all-ceramic IPS e.max full-coverage pressed-ceramic restorations. However, laminate veneers are very delicate and technique-sensitive restorations when compared with all-ceramic full-coverage ones made from the same material. Complete digital design and fabrication of multiple consecutive laminate veneers seems to be very challenging. This clinical report presents the digital workflow for the virtual design and fabrication of multiple laminate veneers in a patient for enhancing the esthetics of his maxillary anterior teeth. A step-by-step process is presented with a discussion of the advantages and disadvantages of this novel technique. Additionally, the use of lithium disilicate ceramic as the material of choice and the rationale for such a decision is discussed.

Isolation of uranium mill tailings and their component radionuclides from the biosphere; some earth science perspectives

Science.gov (United States)

Landa, Edward

1980-01-01

Uranium mining and milling is an expanding activity in the. Western United States. Although the milling process yields a uranium concentrate, the large volume of tailings remaining contains about 85 percent of the radioactivity originally associated with the ore. By virtue of the physical and chemical processing of the ore and the redistribution of the contained radionuclides at the Earth's surface, these tailings constitute a technologically enhanced source of natural radiation exposure. Sources of potential human radiation exposure from uranium mill tailings include the emanation of radon gas, the transport of particles by wind and water, and the transport of soluble radionuclides, seeping from disposal areas, by ground water. Due to the 77,000 year half-life of thorium-230, the parent of radium-226, the environmental effects associated with radionuclides contained in these railings must be conceived of within the framework of geologic processes operating over geologic time. The magnitude of erosion of cover materials and tailings and the extent of geochemical mobilization of the contained radionuclides to the atmosphere and hydrosphere should be considered in the evaluation of the potential, long-term consequences of all proposed uranium mill tailings management plans.

Phase Transitions in Mechanically Milled Mn-Al-C Permanent Magnets

Directory of Open Access Journals (Sweden)

Michael J. Lucis

2014-04-01

Full Text Available Mn-Al powders were prepared by rapid solidification followed by high-energy mechanical milling. The rapid solidification resulted in single-phase ε. The milling was performed in both the ε phase and the τ phase, with the τ-phase formation accomplished through a heat treatment at 500 °C for 10 min. For the ε-milled samples, the conversion of the ε to the τ phase was accomplished after milling via the same heat treatment. Mechanical milling induced a significant increase in coercivity in both cases, reaching 4.5 kOe and 4.1 kOe, respectively, followed by a decrease upon further milling. The increase in coercivity was the result of grain refinement induced by the high-energy mechanical milling. Additionally, in both cases a loss in magnetization was observed. Milling in the ε phase showed a smaller decrease in the magnetization due to a higher content of the τ phase. The loss in magnetization was attributed to a stress-induced transition to the equilibrium phases, as no site disorder or oxidation was observed. Surfactant-assisted milling in oleic acid also improved coercivity, but in this case values reached >4 kOe and remained stable at least through 32 h of milling.

ADAPTIVE NEURO-FUZZY INFERENCE SYSTEM FOR END MILLING

Directory of Open Access Journals (Sweden)

ANGELOS P. MARKOPOULOS

2016-09-01

Full Text Available Soft computing is commonly used as a modelling method in various technological areas. Methods such as Artificial Neural Networks and Fuzzy Logic have found application in manufacturing technology as well. NeuroFuzzy systems, aimed to combine the benefits of both the aforementioned Artificial Intelligence methods, are a subject of research lately as have proven to be superior compared to other methods. In this paper an adaptive neuro-fuzzy inference system for the prediction of surface roughness in end milling is presented. Spindle speed, feed rate, depth of cut and vibrations were used as independent input variables, while roughness parameter Ra as dependent output variable. Several variations are tested and the results of the optimum system are presented. Final results indicate that the proposed model can accurately predict surface roughness, even for input that was not used in training.

Marginal and internal fit of pressed lithium disilicate inlays fabricated with milling, 3D printing, and conventional technologies.

Science.gov (United States)

Homsy, Foudda R; Özcan, Mutlu; Khoury, Marwan; Majzoub, Zeina A K

2017-09-29

The subtractive and additive computer-aided design and computer-aided manufacturing (CAD-CAM) of lithium disilicate partial coverage restorations is poorly documented. The purpose of this in vitro study was to compare the marginal and internal fit accuracy of lithium disilicate glass-ceramic inlays fabricated with conventional, milled, and 3-dimensional (3D) printed wax patterns. A dentoform mandibular first molar was prepared for a mesio-occlusal ceramic inlay. Five groups of 15 inlays were obtained through conventional impression and manual wax pattern (group CICW); conventional impression, laboratory scanning of the stone die, CAD-CAM milled wax blanks (group CIDW) or 3D printed wax patterns (group CI3DW); and scanning of the master preparation with intraoral scanner and CAD-CAM milled (group DIDW) or 3D printed wax patterns (group DI3DW). The same design was used to produce the wax patterns in the last 4 groups. The replica technique was used to measure marginal and internal adaptation by using stereomicroscopy. Mixed-model ANOVA was used to assess differences according to the groups and discrepancy location (α=.05). Group DIDW showed the smallest marginal discrepancy (24.3 μm) compared with those of groups CICW (45.1 μm), CIDW (33.7 μm), CI3DW (39.8 μm), and DI3DW (39.7 μm) (Pimpressions and subtractive milling of wax patterns resulted in better marginal and internal fit accuracy than either conventional impression/fabrication or additive 3D manufacturing. Three-dimensional printed wax patterns yielded fit values similar to those of the conventionally waxed inlays. Copyright © 2017 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Treatment of Olive Mill Wastewater and the Use of Polyphenols Obtained After Treatment

Directory of Open Access Journals (Sweden)

Semih Otles

2012-04-01

Full Text Available Olive mill wastes are signicant environmental problem especially in Mediterranean areas where they are generated in huge quantities in a short period of time. They are phytotoxic materials because of their high phenol, lipid and organic acid concentrations, but these wastes also contain valuable resources that could be recycled such as a large proportion of organic matter and a wide range of nutrients. The effluent from olive oil mills contains a large amount of polyphenols that have antioxidant properties. The market value of these antioxidants is high and they are commonly used in the food, cosmetics, pharmaceutics and chemical industries. For the management of olive mill wastewater (OMW and other olive residues, various treatment methods can be used. Many scientists work on more efficient and cheaper treatment alternatives. Due to the great variety of compounds in the waste, several technologies to remove the harmful compounds for the environment should be used single or together. Some of the most used OMW treatments are drying / evaporation, forced evaporation, thermal treatment, centrifugation-ultraltration, electrocoagulation, composting, lagooning, adsorption, powdered activated carbon, filtration, sand filtration, membrane filtration, ultrafiltration, precipitation / flocculation, distillation, electrolysis, co-composting, advanced oxidation processes (AOPs such as ozonation, hydrogen peroxide / ferrous iron oxidation (the so-called Fentons reagent. Several OMW treatment technologies have been developed aiming at the removal of the main toxic organic compounds. A lot of factors must be considered to choose the treatment methods among them the investment, required area, specic training of the workers, noise and odour emissions and seasonality of production.

Electron beam irradiation pretreatment and enzymatic saccharification of used newsprint and paper mill wastes

International Nuclear Information System (INIS)

Khan, A.W.; Labrie, J.-P.; McKeown, Joseph

1987-01-01

Electron beam pretreatment of used newsprint, pulp, as well as pulp recovered from clarifier sludge and paper mill sludge, caused the dissociation of cellulose from lignin, and rendered them suitable for enzymatic hydrolysis. A maximum dose of 1 MGy for newsprint and 1.5-2.0 MGy for pulp and paper mill sludge was required to render cellulose present in them in a form which, could be enzymatically saccharified to 90% of completion. Saccharification approaching the theoretical yield was obtained in 2 days with a cellulolytic enzyme system obtained from Trichoderma reesei. As a result of irradiation, water soluble lignin breakdown products, NaOH- soluble lignin, free cellobiose, glucose, mannose, xylose and their polymers, and acetic acid were produced from these materials. (author)

EPA's role in uranium mining and milling

International Nuclear Information System (INIS)

Smith, P.B.

1980-01-01

EPA's role and actions in regulating uranium mining and milling are reviewed and updated. Special emphasis is given to EPA's current activities under the Uranium Mill Tailings Radiation Control Act of 1978

globalization, technology transfer and the knowledge gap

African Journals Online (AJOL)

USER

2011-06-10

Jun 10, 2011 ... manufacturing technology to the less developed countries of the South (Nigeria) in ... the primary sources of progress (Mill 1846 cited .... globalization process as in Asia and Latin. America. The Nigerian technology dream is.

Reclamation of uranium mining and milling disturbances

International Nuclear Information System (INIS)

Farmer, E.E.; Schuman, G.E.

1987-01-01

Since 1945 the history of uranium mining and milling in the US has been a story of wide fluctuations in market prices and in mining and milling capacity. The late 1960's and the 1970's saw a sizeable reduction in the production of yellowcake because of an earlier over-supply, a leveling off of the military demand, and a failure of the nuclear electric power industry to create the anticipated commercial demand. The decline in the domestic production of yellowcake has continued through the early 1980's to the present. Today, there are five operating uranium mills in the US: one in Wyoming, two in Utah, one in New Mexico, and one in Texas. Of these five mills, three are operating on a reduced schedule, as little as three days a month. A significant portion of the current US production of uranium goes overseas to fulfill Japanese, French, and other European contracts. There is still a sizeable reclamation job to be accomplished on old uranium wastes, both tailings impoundments and overburden embankments. Before the Uranium Mill Tailings Control Act of 1978 (PL 95-604), reclamation was frequently omitted altogether, or else done in a haphazard fashion. We do not know the total area of unreclaimed, radioactive, uranium overburden wastes in the western US, but the area is large, probably several thousand hectares. Fortunately, these overburden wastes are almost entirely located in remote areas. Mill tailings are more difficult to reclaim than overburden, and tailings represent a more serious health hazards. There are approximately 25 million metric tons of unreclaimed uranium mill tailings, with variable health hazards, located in the US

Retrieving Storm Electric Fields From Aircraft Field Mill Data. Part 2; Applications

Science.gov (United States)

Koshak, W. J.; Mach, D. M.; Christian, H. J.; Stewart, M. F.; Bateman, M. G.

2005-01-01

The Lagrange multiplier theory and "pitch down method" developed in Part I of this study are applied to complete the calibration of a Citation aircraft that is instrumented with six field mill sensors. When side constraints related to average fields are used, the method performs well in computer simulations. For mill measurement errors of 1 V/m and a 5 V/m error in the mean fair weather field function, the 3-D storm electric field is retrieved to within an error of about 12%. A side constraint that involves estimating the detailed structure of the fair weather field was also tested using computer simulations. For mill measurement errors of 1 V/m, the method retrieves the 3-D storm field to within an error of about 8% if the fair weather field estimate is typically within 1 V/m of the true fair weather field. Using this side constraint and data from fair weather field maneuvers taken on 29 June 2001, the Citation aircraft was calibrated. The resulting calibration matrix was then used to retrieve storm electric fields during a Citation flight on 2 June 2001. The storm field results are encouraging and agree favorably with the results obtained from earlier calibration analyses that were based on iterative techniques.

Evaluation of internal fit of interim crown fabricated with CAD/CAM milling and 3D printing system.

Science.gov (United States)

Lee, Wan-Sun; Lee, Du-Hyeong; Lee, Kyu-Bok

2017-08-01

This study is to evaluate the internal fit of the crown manufactured by CAD/CAM milling method and 3D printing method. The master model was fabricated with stainless steel by using CNC machine and the work model was created from the vinyl-polysiloxane impression. After scanning the working model, the design software is used to design the crown. The saved STL file is used on the CAD/CAM milling method and two types of 3D printing method to produce 10 interim crowns per group. Internal discrepancy measurement uses the silicon replica method and the measured data are analyzed with One-way ANOVA to verify the statistic significance. The discrepancy means (standard deviation) of the 3 groups are 171.6 (97.4) µm for the crown manufactured by the milling system and 149.1 (65.9) and 91.1 (36.4) µm, respectively, for the crowns manufactured with the two types of 3D printing system. There was a statistically significant difference and the 3D printing system group showed more outstanding value than the milling system group. The marginal and internal fit of the interim restoration has more outstanding 3D printing method than the CAD/CAM milling method. Therefore, the 3D printing method is considered as applicable for not only the interim restoration production, but also in the dental prosthesis production with a higher level of completion.

( Rosa damascena Mill.) by microbial inoculation

African Journals Online (AJOL)

This study was carried out to determine the effects of microbial inoculation in breaking seed dormancy and on the germination of Rosa damascena Mill. Seeds of R. damascena Mill. are the most used scented rose species in rose oil production. The most important production centers around the world are Turkey and ...

Estimated dose to man from uranium milling via the beef/milk food-chain pathway

Energy Technology Data Exchange (ETDEWEB)

Rayno, D R

1983-12-01

One of the major pathways of radiological exposure to man from uranium milling operations is through the beef/milk food chain. Studies by various investigators have shown the extent of uptake and distribution of 238U, 234U, 230Th, 226Ra, 210Pb, and 210Po in plants and cattle. These long-lived natural radioisotopes, all nuclides of the uranium decay series, are found in concentrated amounts in uranium mill tailings. In this paper, data from these investigations are used to estimate the dose to man from consumption of beef and milk from cattle that have fed on forage contaminated with the tailings. The estimated doses from this technologically enhanced source are compared with those resulting from average dietary intake of these radionuclides from natural sources.

Application of grey fuzzy logic for the optimization of CNC milling parameters for Al–4.5%Cu–TiC MMCs with multi-performance characteristics

Directory of Open Access Journals (Sweden)

Biswajit Das

2016-06-01

Full Text Available With the major application of MMCs, it is thus necessary to develop an appropriate technology for their efficient machining. Milling is the most common and versatile technology among different machining processes, characterized by an extensive range of metal cutting capacity that places it in a central role in the manufacturing industries. In the present study an attempt has been made to find out the most optimal level of process parameters for CNC milling of Al–4.5%Cu–TiC metal matrix composites using grey-fuzzy algorithm. Taguchi's L25 orthogonal array design is used for performing CNC milling operation on the composite plates. The Grey fuzzy optimization of CNC milling parameters consist of three different output characteristics; such as, cutting force Fc, surface roughness Ra and surface roughness Rz. It was found that a cutting speed of 600 rpm, feed of 40 mm/min and a depth of cut of 0.30 mm is the optimal combination of CNC milling parameters that has produced a high value of grey fuzzy reasoning grade of 0.8191 which is close to the reference value. ANOVA analysis is carried out and it is found that among three different process parameters, the cutting speed played a major role on the determination of GFRG.

Yang-Mills analogs of general-relativistic solutions

International Nuclear Information System (INIS)

Singlton, D.

1998-01-01

Some solutions of Yang-Mills equations, which can be found with the use of the general relativistic theory and Yang-Mills theory, are discussed. Some notes concerning possible physical sense of these solutions are made. Arguments showing that some of such solutions in the Yang-Mills theory (similar to the general relativistic ones) may be connected with the confinement phenomenon are given in particular. The motion of probe particles located into the phonon potential similar to the Schwarz-Child one is briefly discussed for this purpose [ru

Milling and dispersion of multi-walled carbon nanotubes in texanol

Science.gov (United States)

Darsono, Nono; Yoon, Dang-Hyok; Kim, Jaemyung

2008-03-01

Rheological results were used to determine the optimum type of dispersant and its concentration for six commercial dispersants for the dispersion of multi-walled carbon nanotube (MWCNT) agglomerates in texanol. An unsaturated polycarboxylic acid copolymer (BYK P-104) exhibited the optimum performance with the lowest MWCNT slurry viscosity in texanol. The cutting and dispersion efficiencies of MWCNTs with 20 wt.% of BYK P-104 dispersant were compared using conventional ball milling and high energy milling, whereby the latter was found to be more effective. High energy milling for 2 h produced a large portion of MWCNT agglomerates smaller than 150 nm, showing a drastic increase in slurry viscosity due to the dispersion into individual CNTs. On the other hand, 120 h ball milling was required to achieve the agglomerate size of 300 nm with less viscosity increase upon milling. Decrease in the degree of MWCNT crystallinity was observed by both milling, even though 2 h high energy milling showed slightly less damage than 120 h ball milling based on XRD and Raman spectroscopy results.

Milling damage on Carbon Fibre Reinforced Polymer using TiAlN coated End mills

International Nuclear Information System (INIS)

Konneh, Mohamed; Kassim, Abdullah Abdul Rahman; Izman, Sudin

2015-01-01

This paper reports on the damage caused by milling Carbon Fibre Reinforced Composite (CFRP) with 2-flute 4 mm-diameter solid carbide end mills, coated with titanium aluminium nitride. The machining parameters considered in work are, rotation speed, feed rate and depth of cut. Experiments were designed based on Box-Behnken design and the experiments conducted on a Mikrotool DT-110 CNC micro machine. A laser tachometer was used to ascertain a rotational speed for conducting any machining trial. Optical microscopy examination reveals minimum delamination value of 4.05 mm at the spindle speed of 25,000 rpm, depth of cut of 50μm and feed rate of 3 mm/min and the maximum delamination value of 5.04 mm at the spindle speed of 35000 rpm, depth of cut of 150μm and feed rate of 9 mm/min A mathematical model relating the milling parameters and delamination has been established. (paper)

Milling damage on Carbon Fibre Reinforced Polymer using TiAlN coated End mills

Science.gov (United States)

Konneh, Mohamed; Izman, Sudin; Rahman Kassim, Abdullah Abdul

2015-07-01

This paper reports on the damage caused by milling Carbon Fibre Reinforced Composite (CFRP) with 2-flute 4 mm-diameter solid carbide end mills, coated with titanium aluminium nitride. The machining parameters considered in work are, rotation speed, feed rate and depth of cut. Experiments were designed based on Box-Behnken design and the experiments conducted on a Mikrotool DT-110 CNC micro machine. A laser tachometer was used to ascertain a rotational speed for conducting any machining trial. Optical microscopy examination reveals minimum delamination value of 4.05 mm at the spindle speed of 25,000 rpm, depth of cut of 50μm and feed rate of 3 mm/min and the maximum delamination value of 5.04 mm at the spindle speed of 35000 rpm, depth of cut of 150μm and feed rate of 9 mm/min A mathematical model relating the milling parameters and delamination has been established.

Niobium Carbide-Reinforced Al Matrix Composites Produced by High-Energy Ball Milling

Science.gov (United States)

Travessa, Dilermando Nagle; Silva, Marina Judice; Cardoso, Kátia Regina

2017-06-01

Aluminum and its alloys are key materials for the transportation industry as they contribute to the development of lightweight structures. The dispersion of hard ceramic particles in the Al soft matrix can lead to a substantial strengthening effect, resulting in composite materials exhibiting interesting mechanical properties and inspiring their technological use in sectors like the automotive and aerospace industries. Powder metallurgy techniques are attractive to design metal matrix composites, achieving a homogeneous distribution of the reinforcement into the metal matrix. In this work, pure aluminum has been reinforced with particles of niobium carbide (NbC), an extremely hard and stable refractory ceramic. Its use as a reinforcing phase in metal matrix composites has not been deeply explored. Composite powders produced after different milling times, with 10 and 20 vol pct of NbC were produced by high-energy ball milling and characterized by scanning electron microscopy and by X-ray diffraction to establish a relationship between the milling time and size, morphology, and distribution of the particles in the composite powder. Subsequently, an Al/10 pct NbC composite powder was hot extruded into cylindrical bars. The strength of the obtained composite bars is comparable to the commercial high-strength, aeronautical-grade aluminum alloys.

Nanograin formation in milled MoO3 powders

International Nuclear Information System (INIS)

Guerrero-Paz, J; Dorantes-Rosales, H; Aguilar-Martínez, J A; Garibay-Febles, V

2013-01-01

Powder of Molybdenum trioxide was milled for different times in horizontal ball mills. Such powder was characterized by TEM and XRD. Powder was rapidly de-agglomerated and fragmented up to attain nanoplates of two types, amorphous and crystalline. Finally, cold-welding of nanoplates occurred permitting some relaxation process to obtain a more stable energized structure consisting of equiaxial crystalline nanograins after 16 hours of milling.

40 CFR 63.1347 - Standards for raw and finish mills.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Standards for raw and finish mills. 63... and Operating Limits § 63.1347 Standards for raw and finish mills. The owner or operator of each new or existing raw mill or finish mill at a facility which is a major source subject to the provisions...

Surface water contamination by uranium Mining/Milling activities in Northern guangdong province, China

Energy Technology Data Exchange (ETDEWEB)

Wang, Jin; Song, Gang; Chen, Yongheng; Zhu, Li [Key Laboratory of Waters Safety and Protection in the Pearl River Delta, Ministry of Education, Guangzhou University, Guangzhou (China); Liu, Juan [Key Laboratory of Waters Safety and Protection in the Pearl River Delta, Ministry of Education, Guangzhou University, Guangzhou (China); Department of Geosciences, National Taiwan University, Taipei (China); Li, Hongchun [Department of Geosciences, National Taiwan University, Taipei (China); Xiao, Tangfu [State Key Laboratory of Environmental Geochemistry, Institute of Geochemistry, Chinese Academy of Sciences, Guiyang (China); Qi, Jianying [South China Institute of Environmental Science, Ministry of Environmental Protection, Guangzhou (China)

2012-12-15

The northern region of Guangdong Province, China, has suffered from the extensive mining/milling of uranium for several decades. In this study, surface waters in the region were analyzed by inductively coupled plasma optical emission spectrometry (ICP-OES) for the concentrations of uranium (U), thorium (Th), and non-radioactive metals (Fe, Mn, Mg, Li, Co, Cu, Ni, and Zn). Results showed highly elevated concentrations of the studied radionuclides and metals in the discharged effluents and the tailing seepage of the U mining/milling sites. Radionuclide and heavy metal concentrations were also observed to be overall enhanced in the recipient stream that collected the discharged effluents from the industrial site, compared to the control streams, and rivers with no impacts from the U mining/milling sites. They displayed significant spatial variations and a general decrease downstream away from upper point-source discharges of the industrial site. In addition, obvious positive correlations were found between U and Th, Fe, Zn, Li, and Co (R{sup 2} > 0.93, n = 28) in the studied water samples, which suggest for an identical source and transport pathway of these elements. In combination with present surface water chemistry and chemical compositions of uraniferous minerals, the elevation of the analyzed elements in the recipient stream most likely arose from the liquid effluents, processing water, and acid drainage from the U mining/milling facilities. The dispersion of radionuclides and hazardous metals is actually limited to a small area at present, but some potential risk should not be negligible for local ecosystem. The results indicate that environmental remediation work is required to implement and future cleaner production technology should be oriented to avoid wide dispersion of radioactivity and non-radioactive hazards in U mining/milling sites. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Lattice super-Yang-Mills: a virial approach to operator dimensions

International Nuclear Information System (INIS)

Callan, Curtis G.; Heckman, Jonathan; McLoughlin, Tristan; Swanson, Ian

2004-01-01

The task of calculating operator dimensions in the planar limit of N=4 super-Yang-Mills theory can be vastly simplified by mapping the dilatation generator to the Hamiltonian of an integrable spin chain. The Bethe ansatz has been used in this context to compute the spectra of spin chains associated with various sectors of the theory which are known to decouple in the planar (large-Nc) limit. These techniques are powerful at leading order in perturbation theory but become increasingly complicated beyond one loop in the 't Hooft parameter λ=gYM2Nc, where spin chains typically acquire long-range (non-nearest-neighbor) interactions. In certain sectors of the theory, moreover, higher-loop Bethe ansatze do not even exist. We develop a virial expansion of the spin chain Hamiltonian as an alternative to the Bethe ansatz methodology, a method which simplifies the computation of dimensions of multi-impurity operators at higher loops in λ. We use these methods to extract previously reported numerical gauge theory predictions near the BMN limit for comparison with corresponding results on the string theory side of the AdS/CFT correspondence. For completeness, we compare our virial results with predictions that can be derived from current Bethe ansatz technology

Biorefinery Concept Development Based on Wheat Flour Milling

Energy Technology Data Exchange (ETDEWEB)

Elliott, Douglas C.; Orth, Rick J.; Werpy, Todd A.; Gao, Johnway; Eakin, David E.; Schmidt, Andrew J.; Neuenschwander, Gary G.; Murry, J; Flagg, Anthony; Lahman, L; Mennel, D; Lin, C J.; Landucci, Ron; Crockett, John; Peterson, Charles L.

2002-09-22

We are developing an innovative process for the recovery of a starch-rich product from millfeed (the low-value byproduct of wheat flour milling); enzymatic processing of the starch to glucose; and the subsequent processes for conversion of that glucose into a value-added product by either a catalytic or a fermentation process. We have completed the development of the starch recovery step with enzymatic processing and the assessment of its economic viability. The processes to use the glucose product as feedstock for catalytic processing and fermentation processing have been tested in the laboratory. Catalytic processing of the glucose from the extracted starch for polyol production is based on catalytic hydrogenation to sorbitol. Alternatively, fermentation of the extracted starch-derived glucose also provides a pathway to value-added chemical products via a platform chemical, lactic acid. The paper includes results from all the processing areas addressed. Starch extraction and glucose generation from wheat milling byproducts are presented with laboratory and scaled-up processing results. Results of fermentation of the glucose product to lactic acid in shaker flask tests are presented, documenting the minimal requirements for nutrient addition. Stirred batch reactor tests of catalytic hydrogenation of the glucose product to sorbitol are presented with a discussion of contaminant effects on the catalyst.

Modeling the milling tool wear by using an evolutionary SVM-based model from milling runs experimental data

Science.gov (United States)

Nieto, Paulino José García; García-Gonzalo, Esperanza; Vilán, José Antonio Vilán; Robleda, Abraham Segade

2015-12-01

The main aim of this research work is to build a new practical hybrid regression model to predict the milling tool wear in a regular cut as well as entry cut and exit cut of a milling tool. The model was based on Particle Swarm Optimization (PSO) in combination with support vector machines (SVMs). This optimization mechanism involved kernel parameter setting in the SVM training procedure, which significantly influences the regression accuracy. Bearing this in mind, a PSO-SVM-based model, which is based on the statistical learning theory, was successfully used here to predict the milling tool flank wear (output variable) as a function of the following input variables: the time duration of experiment, depth of cut, feed, type of material, etc. To accomplish the objective of this study, the experimental dataset represents experiments from runs on a milling machine under various operating conditions. In this way, data sampled by three different types of sensors (acoustic emission sensor, vibration sensor and current sensor) were acquired at several positions. A second aim is to determine the factors with the greatest bearing on the milling tool flank wear with a view to proposing milling machine's improvements. Firstly, this hybrid PSO-SVM-based regression model captures the main perception of statistical learning theory in order to obtain a good prediction of the dependence among the flank wear (output variable) and input variables (time, depth of cut, feed, etc.). Indeed, regression with optimal hyperparameters was performed and a determination coefficient of 0.95 was obtained. The agreement of this model with experimental data confirmed its good performance. Secondly, the main advantages of this PSO-SVM-based model are its capacity to produce a simple, easy-to-interpret model, its ability to estimate the contributions of the input variables, and its computational efficiency. Finally, the main conclusions of this study are exposed.

Accuracy of Digitally Fabricated Wax Denture Bases and Conventional Completed Complete Dentures

Directory of Open Access Journals (Sweden)

Bogna Stawarczyk

2017-12-01

Full Text Available The purpose of this investigation was to analyze the accuracy of digitally fabricated wax trial dentures and conventionally finalized complete dentures in comparison to a surface tessellation language (STL-dataset. A generated data set for the denture bases and the tooth sockets was used, converted into STL-format, and saved as reference. Five mandibular and 5 maxillary denture bases were milled from wax blanks and denture teeth were waxed into their tooth sockets. Each complete denture was checked on fit, waxed onto the dental cast, and digitized using an optical laboratory scanning device. The complete dentures were completed conventionally using the injection method, finished, and scanned. The resulting STL-datasets were exported into the three-dimensional (3D software GOM Inspect. Each of the 5 mandibular and 5 maxillary complete dentures was aligned with the STL- and the wax trial denture dataset. Alignment was performed based on a best-fit algorithm. A three-dimensional analysis of the spatial divergences in x-, y- and z-axes was performed by the 3D software and visualized in a color-coded illustration. The mean positive and negative deviations between the datasets were calculated automatically. In a direct comparison between maxillary wax trial dentures and complete dentures, complete dentures showed higher deviations from the STL-dataset than the wax trial dentures. The deviations occurred in the area of the teeth as well as in the distal area of the denture bases. In contrast, the highest deviations in both the mandibular wax trial dentures and the mandibular complete dentures were observed in the distal area. The complete dentures showed higher deviations on the occlusal surfaces of the teeth compared to the wax dentures. Computer-aided design/computer-aided manufacturing (CAD/CAM-fabricated wax dentures exhibited fewer deviations from the STL-reference than the complete dentures. The deviations were significantly greater in the

77 FR 43369 - Alumax Mill Products, Inc. Doing Business as Alcoa Mill Products Texarkana a Subsidiary of Alcoa...

Science.gov (United States)

2012-07-24

... Products, Inc., a subsidiary of Alcoa, Inc. The intent of the Department's certification is to properly... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-71,149] Alumax Mill Products, Inc. Doing Business as Alcoa Mill Products Texarkana a Subsidiary of Alcoa, Inc. Nash, TX; Amended...

OPMILL - MICRO COMPUTER PROGRAMMING ENVIRONMENT FOR CNC MILLING MACHINES THREE AXIS EQUATION PLOTTING CAPABILITIES

Science.gov (United States)

Ray, R. B.

1994-01-01

OPMILL is a computer operating system for a Kearney and Trecker milling machine that provides a fast and easy way to program machine part manufacture with an IBM compatible PC. The program gives the machinist an "equation plotter" feature which plots any set of equations that define axis moves (up to three axes simultaneously) and converts those equations to a machine milling program that will move a cutter along a defined path. Other supported functions include: drill with peck, bolt circle, tap, mill arc, quarter circle, circle, circle 2 pass, frame, frame 2 pass, rotary frame, pocket, loop and repeat, and copy blocks. The system includes a tool manager that can handle up to 25 tools and automatically adjusts tool length for each tool. It will display all tool information and stop the milling machine at the appropriate time. Information for the program is entered via a series of menus and compiled to the Kearney and Trecker format. The program can then be loaded into the milling machine, the tool path graphically displayed, and tool change information or the program in Kearney and Trecker format viewed. The program has a complete file handling utility that allows the user to load the program into memory from the hard disk, save the program to the disk with comments, view directories, merge a program on the disk with one in memory, save a portion of a program in memory, and change directories. OPMILL was developed on an IBM PS/2 running DOS 3.3 with 1 MB of RAM. OPMILL was written for an IBM PC or compatible 8088 or 80286 machine connected via an RS-232 port to a Kearney and Trecker Data Mill 700/C Control milling machine. It requires a "D:" drive (fixed-disk or virtual), a browse or text display utility, and an EGA or better display. Users wishing to modify and recompile the source code will also need Turbo BASIC, Turbo C, and Crescent Software's QuickPak for Turbo BASIC. IBM PC and IBM PS/2 are registered trademarks of International Business Machines. Turbo

Fabrication of Al/A206–Al2O3 nano/micro composite by combining ball milling and stir casting technology

International Nuclear Information System (INIS)

Tahamtan, S.; Halvaee, A.; Emamy, M.; Zabihi, M.S.

2013-01-01

Highlights: ► Uniform distribution of alumina particles in molten Al alloy by using MMMC. ► Improvement in wettability of alumina particles with molten Al alloy by using MMMC. ► Porosity content in Al/A206-alumina composite decreased by using MMMC. ► Improvement in tensile strength of Al/A206-alumina composite by using MMMC. ► Decrease in interfacial reaction product by incorporating MMMC in semi-solid state. - Abstract: Al206/5vol.%Al 2 O 3p cast composites were fabricated by the injection of reinforcing particles into molten Al alloy in two different forms, i.e. as Al 2 O 3 particles and milled particulates of alumina with Al and Mg powders. The resultant milled powders (Master Metal Matrix Composite (MMMC)) were then added into the molten Al alloy both in semi-solid state and above liquidus temperature. Effects of powder addition technique, reinforcement particle size and casting temperature on distribution and incorporation of reinforcing particles into molten Al alloy were investigated. Morphology evolution of powders during milling, microscopic examinations of composite and matrix alloy were studied by scanning electron microscopy (SEM). X-ray diffraction (XRD) analysis was also used to determine the possible interaction between powders after ball milling process. Results showed that injection of powders in the form of MMMC leads to considerable improvement in incorporation and distribution of Al 2 O 3p in the Al206 matrix alloy leading to the improvement in tensile properties. Improvement in tensile properties is attributed to the better wetting of Al 2 O 3p by melt as well as removing microchannels and roughness on alumina particles as a consequence of ball milling process

Complete mitochondrial genome of Eruca sativa Mill. (Garden rocket.

Directory of Open Access Journals (Sweden)

Yankun Wang

Full Text Available Eruca sativa (Cruciferae family is an ancient crop of great economic and agronomic importance. Here, the complete mitochondrial genome of Eruca sativa was sequenced and annotated. The circular molecule is 247,696 bp long, with a G+C content of 45.07%, containing 33 protein-coding genes, three rRNA genes, and 18 tRNA genes. The Eruca sativa mitochondrial genome may be divided into six master circles and four subgenomic molecules via three pairwise large repeats, resulting in a more dynamic structure of the Eruca sativa mtDNA compared with other cruciferous mitotypes. Comparison with the Brassica napus MtDNA revealed that most of the genes with known function are conserved between these two mitotypes except for the ccmFN2 and rrn18 genes, and 27 point mutations were scattered in the 14 protein-coding genes. Evolutionary relationships analysis suggested that Eruca sativa is more closely related to the Brassica species and to Raphanus sativus than to Arabidopsis thaliana.

Optimal Cluster Mill Pass Scheduling With an Accurate and Rapid New Strip Crown Model

International Nuclear Information System (INIS)

Malik, Arif S.; Grandhi, Ramana V.; Zipf, Mark E.

2007-01-01

Besides the requirement to roll coiled sheet at high levels of productivity, the optimal pass scheduling of cluster-type reversing cold mills presents the added challenge of assigning mill parameters that facilitate the best possible strip flatness. The pressures of intense global competition, and the requirements for increasingly thinner, higher quality specialty sheet products that are more difficult to roll, continue to force metal producers to commission innovative flatness-control technologies. This means that during the on-line computerized set-up of rolling mills, the mathematical model should not only determine the minimum total number of passes and maximum rolling speed, it should simultaneously optimize the pass-schedule so that desired flatness is assured, either by manual or automated means. In many cases today, however, on-line prediction of strip crown and corresponding flatness for the complex cluster-type rolling mills is typically addressed either by trial and error, by approximate deflection models for equivalent vertical roll-stacks, or by non-physical pattern recognition style models. The abundance of the aforementioned methods is largely due to the complexity of cluster-type mill configurations and the lack of deflection models with sufficient accuracy and speed for on-line use. Without adequate assignment of the pass-schedule set-up parameters, it may be difficult or impossible to achieve the required strip flatness. In this paper, we demonstrate optimization of cluster mill pass-schedules using a new accurate and rapid strip crown model. This pass-schedule optimization includes computations of the predicted strip thickness profile to validate mathematical constraints. In contrast to many of the existing methods for on-line prediction of strip crown and flatness on cluster mills, the demonstrated method requires minimal prior tuning and no extensive training with collected mill data. To rapidly and accurately solve the multi-contact problem

46 CFR 50.25-3 - Manufacturer or mill certification.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Manufacturer or mill certification. 50.25-3 Section 50... PROVISIONS Acceptance of Material and Piping Components § 50.25-3 Manufacturer or mill certification. (a) A manufacturer or mill producing materials used in certain products for installation on inspected vessels, shall...

The role of microorganisms in the formation of pitch deposits in pulp and paper mills.

Science.gov (United States)

Stranger-Johannessen, M

1984-01-01

The cause of pitch deposit formation seems still not fully understood. The work reported here demonstrates that microorganisms effect the agglomeration of emulgated resin droplets and the formation of sticky precipitates. Pitch deposits from mills consist mainly of ethanol-soluble resins. It is also the ethanol-soluble fraction of wood resins which forms stable emulsions and which is easily agglomerated by microorganisms. Pitch deposits, collected from various pulp and paper mills, were all found to contain large amounts of microorganisms. Sterile resin emulsions prepared from pitch deposits remained stable over long periods. After inoculation with microorganisms the emulsions were destabilized and the resins completely precipitated as sticky lumps. Various bacteria and fungi are capable of agglomerating the resins, but species isolated from water, pulp and slime in paper mills were usually most effective. Resins from fresh wood were precipitated at a faster rate than aged resins. Problems of pitch formation can be considerably reduced when microbial growth is kept under control in the production system. To be effective, the control measures, e.g. slimicides, must be applied at the right place and time, and in the correct concentrations. This presupposes a thorough knowledge of the plant's microbiological condition which can only be obtained by microbiological examination. Practical cases of the appropriate application of biocides in pulp and paper mill systems are discussed.

Determination of the Tapping Part Diameter of the Thread Mill

Directory of Open Access Journals (Sweden)

A. E. Dreval'

2015-01-01

Full Text Available Currently, there is a tendency to increase the proportion of thread milling operations, among other ways of tapping, which is associated with increasing number of CNC machines, flexibility and versatility of the process.Developments presently existing in the RF and used in the thread mills deal, mainly, with the thread milling cutter designs, to process internal and external thread with straight flutes made from high-speed steel.The paper presents a technique to calculate and select the initial design parameters, i.e. the external diameter of the tapping part of thread milling cutter, which is chosen as a basic computational design. The analysis of directories of tool companies containing foreign de-signs of solid thread end-milling cutters has shown that most of them rep-resent the thread cutter designs made of solid carbide. There are solid and interlocking side milling cutters, which use a tapping part both as a single-disk and as a multi-disk one; chip flutes are made to be both as direct and as screw; solid designs of cutters are made from carbide with a diameter of up to 20 ... 25 mm; thread cutters can be left- and right-hand cutting; Designs of the combined thread mills are proposed; internal channels are used for coolant supply.It is shown that the purpose of the external diameter of the tapping part of the thread mill should take into account the effect of the thread mill diameter on the milling process performance, precision of thread profile received, taper thread, tool strength, and the volume of flutes.The analysis has shown that when choosing the external diameter of the thread mill it worth taking its maximum diameter to improve the char-acteristics of the process under the restrictions imposed on the accuracy of the formed thread.

Radiological health aspects of uranium milling

International Nuclear Information System (INIS)

Fisher, D.R.; Stoetzel, G.A.

1983-05-01

This report describes the operation of conventional and unconventional uranium milling processes, the potential for occupational exposure to ionizing radiation at the mill, methods for radiological safety, methods of evaluating occupational radiation exposures, and current government regulations for protecting workers and ensuring that standards for radiation protection are adhered to. In addition, a survey of current radiological health practices is summarized

Radiological health aspects of uranium milling

Energy Technology Data Exchange (ETDEWEB)

Fisher, D.R.; Stoetzel, G.A.

1983-05-01

This report describes the operation of conventional and unconventional uranium milling processes, the potential for occupational exposure to ionizing radiation at the mill, methods for radiological safety, methods of evaluating occupational radiation exposures, and current government regulations for protecting workers and ensuring that standards for radiation protection are adhered to. In addition, a survey of current radiological health practices is summarized.

Preparation of iron sulphides by high energy ball milling

DEFF Research Database (Denmark)

Lin, R.; Jiang, Jianzhong; Larsen, R.K.

1998-01-01

The reaction of a powder mixture consisting of 50 a.% Fe and 50 a.% S during high energy ball milling has been studied by x-ray diffraction and Mossbauer spectroscopy. After around 19 h of milling FeS2 and FeS havebeen formed. By further milling the FeS compound becomes dominating and only Fe......S with an average crystallite size of about 10 nm was observed after milling times longer than 67 h. Mossbauer spectra obtained with applied fields show that the particles are antiferromagnetic or have a strongly canted spin structure....

Value Added Products from Hemicellulose Utilization in Dry Mill Ethanol Plants

Energy Technology Data Exchange (ETDEWEB)

Rodney Williamson, ICPB; John Magnuson, PNNL; David Reed, INL; Marco Baez, Dyadic; Marion Bradford, ICPB

2007-03-30

The Iowa Corn Promotion Board is the principal contracting entity for this grant funded by the US Department of Agriculture and managed by the US Department of Energy. The Iowa Corn Promotion Board subcontracted with New Jersey Institute of Technology, KiwiChem, Pacific Northwest National Lab and Idaho National Lab to conduct research for this project. KiwiChem conducted the economic engineering assessment of a dry-mill ethanol plant. New Jersey Institute of Technology conducted work on incorporating the organic acids into polymers. Pacific Northwest National Lab conducted work in hydrolysis of hemicellulose, fermentation and chemical catalysis of sugars to value-added chemicals. Idaho National Lab engineered an organism to ferment a specific organic acid. Dyadic, an enzme company, was a collaborator which provided in-kind support for the project. The Iowa Corn Promotion Board collaborated with the Ohio Corn Marketing Board and the Minnesota Corn Merchandising Council in providing cost share for the project. The purpose of this diverse collaboration was to integrate the hydrolysis, the conversion and the polymer applications into one project and increase the likelihood of success. This project had two primary goals: (1) to hydrolyze the hemicellulose fraction of the distillers grain (DG) coproduct coming from the dry-mill ethanol plants and (2) convert the sugars derived from the hemicellulose into value-added co-products via fermentation and chemical catalysis.

Effects of X-ray irradiation to genetic transformation of Eruca sativa Mill mediated by agrobacterium rhizogenes

International Nuclear Information System (INIS)

Wu Zhenhua; Zhang Hong; Liu Bin; Li Ning; Niu Bingtao; Wang Genxuan; Li Sha; Sun Peng

2008-01-01

To investigate the effects of X-ray irradiation to the hairy root induction of Eruca sativa Mill, and to provide basic experimental data for concerted reaction of irradiation to the Genetic transformation technology. The aseptic cotyledons of Eruca sativa Mill were jointly treated with the X-ray at dose of 5, 10, 15, 20 Gy respectively and the different infected time, then the influence of explant age, pre-culturing time, dose of X-ray and infected time were studied. Furthermore, the hairy roots were testified in molecular level by the polymerase chain reaction(PCR). The irradiation of X-ray at dose of 15 Gy can improve the frequency of Eruca sativa Mill hairy root induction in a dose-dependent manner. Moreover, the transformation frequency in pre-infection plus irradiation group is higher than that in pre-irradiation plus infection group at the same irradiation dose. In addition, the PCR analysis also demonstrated that rolB gene of T-DNA from Ri plasmid had been integrated into the genome of the transformed roots. The irradiation of X-ray has some positive effects on the hairy root induction of Eruca sativa Mill, and the optimal revulsive dose is 15 Gy ora little bit more. (authors)

The Influence of Milling on the Dissolution Performance of Simvastatin

Directory of Open Access Journals (Sweden)

Thomas Rades

2010-12-01

Full Text Available Particle size reduction is a simple means to enhance the dissolution rate of poorly water soluble BCS-class II and IV drugs. However, the major drawback of this process is the possible introduction of process induced disorder. Drugs with different molecular arrangements may exhibit altered properties such as solubility and dissolution rate and, therefore, process induced solid state modifications need to be monitored. The aim of this study was two-fold: firstly, to investigate the dissolution rates of milled and unmilled simvastatin; and secondly, to screen for the main milling factors, as well as factor interactions in a dry ball milling process using simvastatin as model drug, and to optimize the milling procedure with regard to the opposing responses particle size and process induced disorder by application of a central composite face centered design. Particle size was assessed by scanning electron microscopy (SEM and image analysis. Process induced disorder was determined by partial least squares (PLS regression modeling of respective X-ray powder diffractograms (XRPD and Raman spectra. Valid and significant quadratic models were built. The investigated milling factors were milling frequency, milling time and ball quantity at a set drug load, out of which milling frequency was found to be the most important factor for particle size as well as process induced disorder. Milling frequency and milling time exhibited an interaction effect on the responses. The optimum milling settings using the maximum number of milling balls (60 balls with 4 mm diameter was determined to be at a milling frequency of 21 Hz and a milling time of 36 min with a resulting primary particle size of 1.4 μm and a process induced disorder of 6.1% (assessed by Raman spectroscopy and 8.4% (assessed by XRPD, at a set optimization limit of < 2 μm for particle size and < 10% for process induced disorder. This optimum was tested experimentally and the process induced disorder

7 CFR 58.419 - Curd mill and miscellaneous equipment.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Curd mill and miscellaneous equipment. 58.419 Section... Service 1 Equipment and Utensils § 58.419 Curd mill and miscellaneous equipment. Knives, hand rakes... of the curd mill should be of stainless steel. All pieces of equipment shall be so constructed that...

Development of an electromechanical principle for wet and dry milling

Science.gov (United States)

Halbedel, Bernd; Kazak, Oleg

2018-05-01

The paper presents a novel electromechanical principle for wet and dry milling of different materials, in which the milling beads are moved under a time- and local-variable magnetic field. A possibility to optimize the milling process in such a milling machine by simulation of the vector gradient distribution of the electromagnetic field in the process room is presented. The mathematical model and simulation methods based on standard software packages are worked out. The results of numerical simulations and experimental measurements of the electromagnetic field in the working chamber of a developed and manufactured laboratory plant correlate well with each other. Using the obtained operating parameters, dry milling experiments with crushed cement clinker and wet milling experiments of organic agents in the laboratory plant are performed and the results are discussed here.

Activity of Plodia interpunctella (Lepidoptera: Pyralidae) in and around flour mills.

Science.gov (United States)

Doud, C W; Phillips, T W

2000-12-01

Studies were conducted at two flour mills where male Indian meal moths, Plodia interpunctella (Hübner), were captured using pheromone-baited traps. Objectives were to determine the distribution of male P. interpunctella at different locations in and around the mills throughout the season, and to monitor moth activity before and after one of the mills was fumigated with methyl bromide to assess efficacy of treatment. Commercially available sticky traps baited with the P. interpunctella sex pheromone were placed at various locations outside and within the larger of the two mills (mill 1). Moths were captured inside mill 1 after methyl bromide fumigations. The highest numbers of P. interpunctella were caught outside the facility and at ground floor locations near outside openings. Additional traps placed in the rooms above the concrete stored-wheat silos at mill 1 during the second year captured more moths than did traps within the mill's production and warehouse areas. In another study, moths were trapped at various distances from a smaller flour mill (mill 2) to determine the distribution of moths outdoors relative to the mill. There was a negative correlation between moth capture and distance from the facility, which suggested that moth activity was concentrated at or near the flour mill. The effectiveness of the methyl bromide fumigations in suppressing moth populations could not be assessed with certainty because moths captured after fumigation may have immigrated from outside through opened loading bay warehouse doors. This study documents high levels of P. interpunctella outdoors relative to those recorded inside a food processing facility. Potential for immigration of P. interpunctella into flour mills and other stored product facilities from other sources may be greater than previously recognized. Moth entry into a food processing facility after fumigation is a problem that should be addressed by pest managers.

33 CFR 117.225 - Yellow Mill Channel.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Yellow Mill Channel. 117.225 Section 117.225 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements Connecticut § 117.225 Yellow Mill Channel. The...

Coal Moisture Estimation in Power Plant Mills

DEFF Research Database (Denmark)

Andersen, Palle; Bendtsen, Jan Dimon; Pedersen, Tom S.

2009-01-01

Knowledge of moisture content in raw coal feed to a power plant coal mill is of importance for efficient operation of the mill. The moisture is commonly measured approximately once a day using offline chemical analysis methods; however, it would be advantageous for the dynamic operation...... of the plant if an on-line estimate were available. In this paper we such propose an on-line estimator (an extended Kalman filter) that uses only existing measurements. The scheme is tested on actual coal mill data collected during a one-month operating period, and it is found that the daily measured moisture...

Revegetation and rock cover for stabilization of inactive uranium mill tailings disposal sites. Final report

Energy Technology Data Exchange (ETDEWEB)

Beedlow, P.A.

1984-05-01

Guidelines for using vegetation and rock to protect inactive uranium mill tailings from erosion were developed by Pacific Northwest Laboratory as part of the Department of Energy's Uranium Mill Tailings Remedial Action Project (UMTRAP) Technology Development program. Information on soils, climate, and vegetation were collected for 20 inactive tailings sites in the western United States. Sites were grouped according to similarities in climate and vegetation. Soil loss for those sites was characterized using the Universal Soil Loss Equation. Test plots were used to evaluate (1) the interaction between vegetation and sealant barrier systems and (2) the effects of surface rock on soil water and vegetation. Lysimeter and simulation studies were used to direct and support field experiments. 49 references, 17 figures, 16 tables.

Revegetation and rock cover for stabilization of inactive uranium mill tailings disposal sites. Final report

International Nuclear Information System (INIS)

Beedlow, P.A.

1984-05-01

Guidelines for using vegetation and rock to protect inactive uranium mill tailings from erosion were developed by Pacific Northwest Laboratory as part of the Department of Energy's Uranium Mill Tailings Remedial Action Project (UMTRAP) Technology Development program. Information on soils, climate, and vegetation were collected for 20 inactive tailings sites in the western United States. Sites were grouped according to similarities in climate and vegetation. Soil loss for those sites was characterized using the Universal Soil Loss Equation. Test plots were used to evaluate (1) the interaction between vegetation and sealant barrier systems and (2) the effects of surface rock on soil water and vegetation. Lysimeter and simulation studies were used to direct and support field experiments. 49 references, 17 figures, 16 tables

46 CFR 50.25-5 - Products requiring manufacturer or mill certification.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Products requiring manufacturer or mill certification... manufacturer or mill certification. (a) Products required to be certified by a manufacturer or by mill... accepted without referring to its manufacturer or mill certification, if: (1) The product is marked in...

FePt magnetic particles prepared by surfactant-assisted ball milling

Energy Technology Data Exchange (ETDEWEB)

Velasco, V., E-mail: vvjimeno@fis.ucm.es [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, P.O. Box 155, Las Rozas 28230 (Spain); Departamento de Física de Materiales, Universidad Complutense de Madrid, Madrid 28040 (Spain); Hernando, A.; Crespo, P. [Instituto de Magnetismo Aplicado, UCM-ADIF-CSIC, P.O. Box 155, Las Rozas 28230 (Spain); Departamento de Física de Materiales, Universidad Complutense de Madrid, Madrid 28040 (Spain)

2013-10-15

High-energy ball milling of Fe and Pt elemental powders has been carried out under dry and wet (in presence of solvent and surfactants) conditions. Dry milling leads to the formation of the disordered FCC-FePt alloy whereas by the wet milling procedure the main process is the decrease of Fe and Pt particle size, although some dissolution of Pt into Fe grains cannot be ruled out, and no hint of the formation of the FCC-FePt phase is observed even to milling times up to 20 h, as X-ray diffraction, electron microscopy and Mössbauer spectroscopy indicates. The as-milled particles were annealed at 600 °C for 2 h under Ar atmosphere. It is noticed that the disordered fcc-FePt phase observed in particles milled under dry conditions transform to ordered fct phase characterized by a hard magnetic behavior with a coercive field up to 10,000 Oe. However, those particles milled in the surfactant/solvent medium exhibit a soft magnetic behavior with a coercive field of 600 Oe. These results indicate that wet high-energy ball milling is not an adequate technique for obtaining single-phase FePt particles. - Highlights: • FePt particles have been obtained by high-energy ball milling. • In the presence of surfactants and solvents, almost no alloying process takes place. • After annealing, the coercive field of the FePt alloy particles increases from 150 Oe to 10,000 Oe.

Mineralogy and geochemistry of uranium mill tailings

International Nuclear Information System (INIS)

Pagel, M.; Somot, S.

2002-01-01

We have investigated three main types of uranium mill tailings: (1) acid mill tailings (Mounana, Gabon), (2) neutralized acid mill tailings (Ecarpiere and Jouac, France) and (3) alkaline mill tailings (Lodeve, France). We have focused especially on radium behaviour which is of major environmental concern in these tailings, but other metals were also studied. It is shown that in type 1 , trapping of 226 Ra by anglesite and barite is dominant whereas in types 2 and 3, 226 Ra is mainly or significantly scavenged by Fe- Mn oxyhydroxides. This study points out the importance of keeping conditions in which these oxyhydroxides will be stable for the long-term. Uranium would be also released during acidification of the tailings. This shows the importance to know more about the behavior of Ra during the crystallization of oxyhydroxides and during tailings diagenesis. Therefore, it is very important to study the sorption of Ra by clay minerals or late authigeneous minerals such as barite. (author)

75 FR 30844 - General Mills, Inc.; Withdrawal of Food Additive Petition

Science.gov (United States)

2010-06-02

...] (formerly Docket No. 2007F-0454) General Mills, Inc.; Withdrawal of Food Additive Petition AGENCY: Food and... 7M4770) had been filed by General Mills, Inc., One General Mills Blvd., Minneapolis, MN 55426. The... use in food production. General Mills, Inc., has now withdrawn the petition without prejudice to a...

Machinability Evaluation in Hard Milling of AISI D2 Steel

OpenAIRE

Gaitonde, Vinayak Neelakanth; Karnik, Sulse Ramesh; Maciel, Caio Henrique Alves; Rubio, Juan Carlos Campos; Abrão, Alexandre Mendes

2016-01-01

Milling of hardened steel components provides considerable benefits in terms of reduced manufacturing cost and time compared to traditional machining. Temperature variation in milling is an important factor affecting the wear of cutting tools. The poor selection of milling parameters may cause excessive tool wear and increased work surface roughness. Hence, there is a need to study the machinability aspects during milling of hardened steel components. In the present work, influence of cutting...

Annual status report on the Uranium Mill Tailings Remedial Action Program

International Nuclear Information System (INIS)

1989-12-01

This eleventh annual status report summarizes activities of the Uranium Mill Tailings Remedial Action (UMTRA) Project undertaken during Fiscal Year (FY) 1989 by the US Department of Energy (DOE) and other agencies. Project goals for FY 1990 are also presented. An annual report of this type was a statutory requirement through January 1, 1986, pursuant to the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law (PL) 95--604. The DOE will continue to submit an annual report through project completion in order to inform the public of yearly project status. Title I of the UMTRCA authorizes the DOE, in cooperation with affected states and Indian tribes within whose boundaries designated uranium processing sites are located, to provide a program of assessment and remedial action at such sites. The purpose of the remedial action is to stabilize and control the tailings and other residual radioactive materials located on the inactive uranium processing sites in a safe and environmentally sound manner and to minimize or eliminate potential radiation health hazards. Commercial and residential properties in the vicinity of designated processing sites that are contaminated with material from the sites, herein referred to as ''vicinity properties,'' are also eligible for remedial action. Included in the UMTRA Project are 24 inactive uranium processing sites and associated vicinity properties located in 10 states, and the vicinity properties associated with Edgemont, South Dakota, an inactive uranium mill currently owned by the Tennessee Valley Authority (TVA)

Annual status report on the Uranium Mill Tailings Remedial Action Program

Energy Technology Data Exchange (ETDEWEB)

1989-12-01

This eleventh annual status report summarizes activities of the Uranium Mill Tailings Remedial Action (UMTRA) Project undertaken during Fiscal Year (FY) 1989 by the US Department of Energy (DOE) and other agencies. Project goals for FY 1990 are also presented. An annual report of this type was a statutory requirement through January 1, 1986, pursuant to the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978, Public Law (PL) 95--604. The DOE will continue to submit an annual report through project completion in order to inform the public of yearly project status. Title I of the UMTRCA authorizes the DOE, in cooperation with affected states and Indian tribes within whose boundaries designated uranium processing sites are located, to provide a program of assessment and remedial action at such sites. The purpose of the remedial action is to stabilize and control the tailings and other residual radioactive materials located on the inactive uranium processing sites in a safe and environmentally sound manner and to minimize or eliminate potential radiation health hazards. Commercial and residential properties in the vicinity of designated processing sites that are contaminated with material from the sites, herein referred to as vicinity properties,'' are also eligible for remedial action. Included in the UMTRA Project are 24 inactive uranium processing sites and associated vicinity properties located in 10 states, and the vicinity properties associated with Edgemont, South Dakota, an inactive uranium mill currently owned by the Tennessee Valley Authority (TVA).

Analytical Modelling Of Milling For Tool Design And Selection

International Nuclear Information System (INIS)

Fontaine, M.; Devillez, A.; Dudzinski, D.

2007-01-01

This paper presents an efficient analytical model which allows to simulate a large panel of milling operations. A geometrical description of common end mills and of their engagement in the workpiece material is proposed. The internal radius of the rounded part of the tool envelope is used to define the considered type of mill. The cutting edge position is described for a constant lead helix and for a constant local helix angle. A thermomechanical approach of oblique cutting is applied to predict forces acting on the tool and these results are compared with experimental data obtained from milling tests on a 42CrMo4 steel for three classical types of mills. The influence of some tool's geometrical parameters on predicted cutting forces is presented in order to propose optimisation criteria for design and selection of cutting tools

IGCC power plant integrated to a Finnish pulp and paper mill. IEA Bioenergy. Techno-economic analysis activity

Energy Technology Data Exchange (ETDEWEB)

Koljonen, T.; Solantausta, Y. [VTT Energy, Espoo (Finland). New Energy Technologies; Salo, K.; Horvath, A. [Carbona Inc. (Finland)

1999-11-01

In Finland, the pulp and paper industry is the largest consumer of energy among the industries and its power demand will increase due to economical and strict environ- mental requirements. The ageing of oil and biomass boilers in Finland also represents a window of opportunity for the introduction of new environmentally sound technology with a high efficiency in power production, e.g., in biomass gasification. This site-specific study describes the technical and economic feasibility of a biomass gasification combined cycle producing heat and power for a typical Finnish pulp and paper mill. The mill produces SC (super calantered) paper 500 000 ADt/a. The paper mill employs sulphate pulp and GW (ground wood) pulp. The capacity of the pulp mill is 400 000 ADt/a (air dry ton/year) of which 120 000 ADt/a is used at the site. The heat demand of the integrate is covered by a recovery boiler and a bark boiler. A condensing steam turbine with two extractions generates electricity for the mill. The aim is to replace an old bark boiler by an IGCC (Integrated Gasification Combined Cycle) to enhance the economy and environmental performance of the power plant. The IGCC feasibility study is conducted for an pulp and paper integrate because of its suitable infrastructure for IGCC and a large amount of wood waste available at the site. For comparison, the feasibility of an IGCC integrated to a pulp mill is also assessed. The IGCC concept described is based on research and development work performed by Carbona, Inc., who acquired the rights for know-how of Enviropower, Inc. The operation and design of the IGCC concept is based on a 20 MWe gas turbine (MW151). The heat of gas turbine exhaust gas is utilised in a HRSG (Heat Recovery Steam Generator) of two pressure levels to generate steam for the pulp and paper mill and the steam turbine. The MCC power plant operates in condensing mode. The total investment cost of the IGCC plant is estimated at FIM 417 million (USD 83.4 million

IGCC power plant integrated to a Finnish pulp and paper mill. IEA Bioenergy. Techno-economic analysis activity

International Nuclear Information System (INIS)

Koljonen, T.; Solantausta, Y.

1999-01-01

In Finland, the pulp and paper industry is the largest consumer of energy among the industries and its power demand will increase due to economical and strict environ- mental requirements. The ageing of oil and biomass boilers in Finland also represents a window of opportunity for the introduction of new environmentally sound technology with a high efficiency in power production, e.g., in biomass gasification. This site-specific study describes the technical and economic feasibility of a biomass gasification combined cycle producing heat and power for a typical Finnish pulp and paper mill. The mill produces SC (super calantered) paper 500 000 ADt/a. The paper mill employs sulphate pulp and GW (ground wood) pulp. The capacity of the pulp mill is 400 000 ADt/a (air dry ton/year) of which 120 000 ADt/a is used at the site. The heat demand of the integrate is covered by a recovery boiler and a bark boiler. A condensing steam turbine with two extractions generates electricity for the mill. The aim is to replace an old bark boiler by an IGCC (Integrated Gasification Combined Cycle) to enhance the economy and environmental performance of the power plant. The IGCC feasibility study is conducted for an pulp and paper integrate because of its suitable infrastructure for IGCC and a large amount of wood waste available at the site. For comparison, the feasibility of an IGCC integrated to a pulp mill is also assessed. The IGCC concept described is based on research and development work performed by Carbona, Inc., who acquired the rights for know-how of Enviropower, Inc. The operation and design of the IGCC concept is based on a 20 MWe gas turbine (MW151). The heat of gas turbine exhaust gas is utilised in a HRSG (Heat Recovery Steam Generator) of two pressure levels to generate steam for the pulp and paper mill and the steam turbine. The MCC power plant operates in condensing mode. The total investment cost of the IGCC plant is estimated at FIM 417 million (USD 83.4 million

Higher derivative super Yang-Mills theories

International Nuclear Information System (INIS)

Bergshoeff, E.; Rakowski, M.; Sezgin, E.

1986-11-01

The most general higher derivative Yang-Mills actions of the type (F 2 +α2F 4 ) which are globally supersymmetric up to order α 2 in six and ten dimensional spacetimes are given. The F 4 -terms turn out to occur in the combination α 2 (tr F 4 - 1/4(tr F 2 ) 2 ), where the trace is over the Lorentz indices. This result agrees with the low energy limit of the open superstring in ten dimensions, where α is the string tension. Surprisingly, the transformation rules of the Yang-Mills multiplet receive order α 2 corrections even in the off-shell formulation. For the case of Abelian Yang-Mills group, the action is expressed in Born-Infeld form with a metric generically given by (1+α 2 F 2 +...). (author)

Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al2O3 Nanocomposite Synthesized by Ball Milling and Powder Metallurgy

Science.gov (United States)

Matori, Khamirul Amin; Ostovan, Farhad; Abdul Aziz, Sidek; Mamat, Md Shuhazlly

2017-01-01

The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al2O3 (Al-5Al2O3) has been investigated. Al-5Al2O3 nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al2O3 nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD) analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness (HV), nano-hardness (HN), and Young’s modulus (E) of Al-5Al2O3 nanocomposites. HV, HN, and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively. PMID:29072632

Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al2O3 Nanocomposite Synthesized by Ball Milling and Powder Metallurgy

Directory of Open Access Journals (Sweden)

Meysam Toozandehjani

2017-10-01

Full Text Available The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al2O3 (Al-5Al2O3 has been investigated. Al-5Al2O3 nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al2O3 nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness (HV, nano-hardness (HN, and Young’s modulus (E of Al-5Al2O3 nanocomposites. HV, HN, and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively.

33 CFR 117.800 - Mill Neck Creek.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Mill Neck Creek. 117.800 Section 117.800 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements New York § 117.800 Mill Neck Creek. The draw of the...

Agar agar-stabilized milled zerovalent iron particles for in situ groundwater remediation

Energy Technology Data Exchange (ETDEWEB)

Velimirovic, Milica; Schmid, Doris; Wagner, Stephan; Micić, Vesna; Kammer, Frank von der; Hofmann, Thilo, E-mail: thilo.hofmann@univie.ac.at

2016-09-01

Submicron-scale milled zerovalent iron (milled ZVI) particles produced by grinding macroscopic raw materials could provide a cost-effective alternative to nanoscale zerovalent iron (nZVI) particles for in situ degradation of chlorinated aliphatic hydrocarbons in groundwater. However, the aggregation and settling of bare milled ZVI particles from suspension presents a significant obstacle to their in situ application for groundwater remediation. In our investigations we reduced the rapid aggregation and settling rate of bare milled ZVI particles from suspension by stabilization with a “green” agar agar polymer. The transport potential of stabilized milled ZVI particle suspensions in a diverse array of natural heterogeneous porous media was evaluated in a series of well-controlled laboratory column experiments. The impact of agar agar on trichloroethene (TCE) removal by milled ZVI particles was assessed in laboratory-scale batch reactors. The use of agar agar significantly enhanced the transport of milled ZVI particles in all of the investigated porous media. Reactivity tests showed that the agar agar-stabilized milled ZVI particles were reactive towards TCE, but that their reactivity was an order of magnitude less than that of bare, non-stabilized milled ZVI particles. Our results suggest that milled ZVI particles could be used as an alternative to nZVI particles as their potential for emplacement into contaminated zone, their reactivity, and expected longevity are beneficial for in situ groundwater remediation. - Highlights: • Rapid aggregation and sedimentation were observed in bare milled ZVI particles. • Agar agar improved the stability of milled ZVI particle suspensions. • Agar agar enhanced the transport of milled ZVI particles in heterogeneous sands. • Agar agar reduced the reactivity of milled ZVI particles towards TCE.

Agar agar-stabilized milled zerovalent iron particles for in situ groundwater remediation

International Nuclear Information System (INIS)

Velimirovic, Milica; Schmid, Doris; Wagner, Stephan; Micić, Vesna; Kammer, Frank von der; Hofmann, Thilo

2016-01-01

Submicron-scale milled zerovalent iron (milled ZVI) particles produced by grinding macroscopic raw materials could provide a cost-effective alternative to nanoscale zerovalent iron (nZVI) particles for in situ degradation of chlorinated aliphatic hydrocarbons in groundwater. However, the aggregation and settling of bare milled ZVI particles from suspension presents a significant obstacle to their in situ application for groundwater remediation. In our investigations we reduced the rapid aggregation and settling rate of bare milled ZVI particles from suspension by stabilization with a “green” agar agar polymer. The transport potential of stabilized milled ZVI particle suspensions in a diverse array of natural heterogeneous porous media was evaluated in a series of well-controlled laboratory column experiments. The impact of agar agar on trichloroethene (TCE) removal by milled ZVI particles was assessed in laboratory-scale batch reactors. The use of agar agar significantly enhanced the transport of milled ZVI particles in all of the investigated porous media. Reactivity tests showed that the agar agar-stabilized milled ZVI particles were reactive towards TCE, but that their reactivity was an order of magnitude less than that of bare, non-stabilized milled ZVI particles. Our results suggest that milled ZVI particles could be used as an alternative to nZVI particles as their potential for emplacement into contaminated zone, their reactivity, and expected longevity are beneficial for in situ groundwater remediation. - Highlights: • Rapid aggregation and sedimentation were observed in bare milled ZVI particles. • Agar agar improved the stability of milled ZVI particle suspensions. • Agar agar enhanced the transport of milled ZVI particles in heterogeneous sands. • Agar agar reduced the reactivity of milled ZVI particles towards TCE.

Improved hydrogen sorption kinetics in wet ball milled Mg hydrides

Energy Technology Data Exchange (ETDEWEB)

Meng, Li

2011-05-04

In this work, wet ball milling method is used in order to improve hydrogen sorption behaviour due to its improved microstructure of solid hydrogen materials. Compared to traditional ball milling method, wet ball milling has benefits on improvement of MgH{sub 2} microstructure and further influences on its hydrogen sorption behavior. With the help of solvent tetrahydrofuran (THF), wet ball milled MgH{sub 2} powder has much smaller particle size and its specific surface area is 7 times as large as that of dry ball milled MgH{sub 2} powder. Although after ball milling the grain size is decreased a lot compared to as-received MgH{sub 2} powder, the grain size of wet ball milled MgH{sub 2} powder is larger than that of dry ball milled MgH{sub 2} powder due to the lubricant effect of solvent THF during wet ball milling. The improved particle size and specific surface area of wet ball milled MgH{sub 2} powder is found to be determining its hydrogen sorption kinetics especially at relatively low temperatures. And it also shows good cycling sorption behavior, which decides on its industrial applicability. With three different catalysts MgH{sub 2} powder shows improved hydrogen sorption behavior as well as the cyclic sorption behavior. Among them, the Nb{sub 2}O{sub 5} catalyst is found to be the most effective one in this work. Compared to the wet ball milled MgH{sub 2} powder, the particle size and specific surface area of the MgH{sub 2} powder with catalysts are similar to the previous ones, while the grain size of the MgH{sub 2} with catalysts is much finer. In this case, two reasons for hydrogen sorption improvement are suggested: one is the reduction of the grain size. The other may be as pointed out in some literatures that formation of new oxidation could enhance the hydrogen sorption kinetics, which is also the reason why its hydrogen capacity is decreased compared to without catalysts. After further ball milling, the specific surface area of wet ball milled Mg

Application of the Dose Limitation System to the Mining and Milling of Radioactive Ores

International Nuclear Information System (INIS)

1987-01-01

This publication is one of the Safety Guides to the Code of Practice on Radiation Protection of Workers in the Mining and Milling of Radioactive Ores, 1983 Edition, which was published as a joint IAEA/ILO/WHO publication (IAEA Safety Series No.26). This Safety Guide is intended to demonstrate as well as facilitate the application of the principles of optimization in the control of risk among the workers engaged in the mining and milling of radioactive ores and to give some guidance on suitable technology. The International Atomic Energy Agency, jointly with the World Health Organization, the International Labour Organisation and the OECD Nuclear Energy Agency, published the Basic Safety Standards for Radiation Protection, 1982 Edition (IAEA Safety Series No. 9). The Basic Safety Standards outline the principles of radiation protection and also the basic requirements to be followed in the implementation of radiation protection control. These principles are further developed in the case of mining and milling of radioactive ores in the joint IAEA/ILO/WHO Code of Practice on Radiation Protection of Workers in the Mining and Milling of Radioactive Ores (IAEA Safety Series No. 26). This Safety Guide on the Application of the Dose Limitation System to the Mining and Milling of Radioactive Ores was prepared by an Advisory Group which met for the first time in Portoroz, Yugoslavia, from 22 to 26 August 1983, and then again from 6 to 10 August 1984, in Vienna. Following the second Advisory Group meeting the draft was further reviewed by A. Dory from Canada who also was a participant of the two Advisory Group meetings held earlier. After the consultant's review the draft was circulated among the members of the Advisory Group for a further check. The final version of the draft was prepared by the Secretariat with the help of a consultant

Health physics program for the Edgemont Uranium Mill decommissioning project

International Nuclear Information System (INIS)

Polehn, J.L.; Wallace, R.G.; Reed, R.P.; Wilson, G.T.

1986-01-01

The Tennessee Valley Authority (TVA) is actively involved in decommissioning a uranium mill located near the town of Edgemont, South Dakota. The Edgemont Mill Decommissioning Project, which is unique in many respects, will involve dismantlement of the old inactive mill building and excavation and transportation of several million tons of uranium mill tailings to a permanent disposal site. To ensure that workers are adequately protected from radiation exposure during decommissioning operations, a health physics program appropriate for the decommissioning situation was developed. The Edgemont Mill Decommissioning Project Health Physics Manual (HPM) gives the programmatic requirements for worker radiation protection. The requirements of the HPM are implemented by means of detailed onsite operating procedures. The Edgemont project health physics program was developed using currently available regulations and guidance for an operating uranium mill with appropriate modifications for decommissioning. This paper discusses the development, implementation, and documentation of that program

Infrared finiteness in Yang--Mills theories

International Nuclear Information System (INIS)

Appelquist, T.; Carazzone, J.; Kluberg-Stern, H.; Roth, M.

1976-01-01

The infrared divergences of renormalizable theories with coupled massless fields (in particular, the Yang--Mills theory) are shown to cancel for transition probabilities corresponding to finite-energy-resolution detectors, just as in quantum electrodynamics. This result is established through lowest nontrivial order in perturbation theory for the detection of massive muons in a quantum electrodynamic theory containing massless electrons or the detection of massive quarks in a Yang--Mills theory

Asphalt emulsion radon barrier systems for uranium mill tailings - a summary of the technology

International Nuclear Information System (INIS)

Baker, E.G.; Hartley, J.N.; Freeman, H.D.

1983-11-01

Pacific Northwest Laboratory (PNL), has developed an asphalt emulsion cover system to reduce the release of radon from uranium mill tailings. The system has been field-tested at the tailings site in Grand Junction, Colorado. Results from laboratory and field tests indicate that this system effectively reduces radon release to near-background levels ( -2 s -1 ) and has the properties required for long-term effectiveness and stability. Engineering specifications have been developed, and a cost analysis indicates that asphalt emulsion covers are competitive with other cover systems. 6 references, 2 figures, 4 tables

Baseline risk assessment for groundwater contamination at the uranium mill tailings site near Monument Valley, Arizona

International Nuclear Information System (INIS)

1993-09-01

This baseline risk assessment evaluates potential impact to public health or the environment resulting from groundwater contamination at the former uranium mill processing site near Monument Valley, Arizona. The tailings and other contaminated material at this site are being relocated and stabilized in a disposal cell at Mexican Hat, Utah, through the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project. The tailings removal is planned for completion by spring 1994. After the tailings are removed, groundwater contamination at the site will continue to be evaluated. This risk assessment is the first document specific to this site for the Groundwater Project. It will be used to assist in determining what remedial action is needed for contaminated groundwater at the site

Analysis of crystallite size and microdeformation crystal lattice the tungsten carbide milling in mill high energy

International Nuclear Information System (INIS)

Silva, F.T. da; Nunes, M.A.M.; Souza, C.P. de; Gomes, U.U.

2010-01-01

The tungsten carbide (WC) has wide application due to its properties like high melting point, high hardness, wear resistance, oxidation resistance and good electrical conductivity. The microstructural characteristics of the starting powders influences the final properties of the carbide. In this context, the use of nanoparticle powders is an efficient way to improve the final properties of the WC. The high energy milling stands out from other processes to obtain nanometric powders due to constant microstructural changes caused by this process. Therefore, the objective is to undertake an analysis of microstructural characteristics on the crystallite size and microdeformations of the crystal lattice using the technique of X-ray diffraction (XRD) using the Rietveld refinement. The results show an efficiency of the milling process to reduce the crystallite size, leading to a significant deformation in the crystal lattice of WC from 5h milling. (author)

Degree of Milling Effect on Cold Water Rice Quality

Directory of Open Access Journals (Sweden)

Ujjwol Subedi

2018-05-01

Full Text Available The aim of this study was to examine the effects of degree of milling on various rice parameters such as proximate composition, and cooking properties using mathematical model. The experiments were performed in the laboratory of Food Research Division, Nepal Agricultural Research Council. The three different medium type rice varieties of Nepal (Lumle-2, Chhomrong and Machhapuchre-3 were exposed to five different degrees of milling (0%, 6%, 8%, 10% and 12%. The degree of milling (DM level significantly (P≤0.05 affected the milling recovery; head rice yield, nutrient content as well as cooking properties of the rice. Increase in DM resulted in further reduction of protein content, fat content, minerals, milled rice and head rice yield after bran layer was further removed. A positive correlation between DM used in present model, amylose content, kernel elongation and gruel solid loss was observed, however, with an increase in DM; amylose content, kernel elongation and gruel solid loss were found to be increased. Adopting 6 to 8% DM for commercial milling of rice might help to prevent quantitative, qualitative and nutritional loss along with retention of good cooking characteristics.

The dispersion of fine chitosan particles by beads-milling

Science.gov (United States)

Rochima, Emma; Utami, Safira; Hamdani, Herman; Azhary, Sundoro Yoga; Praseptiangga, Danar; Joni, I. Made; Panatarani, Camellia

2018-02-01

This research aimed to produce fine chitosan particles from a crab shell waste by beads-milling method by two different concentration of PEG as dispersing agent (150 and 300 wt. %). The characterization was performed to obtain the size and size distribution, the characteristics of functional groups and the degree of deacetylation. The results showed that the chitosan fine particles was obtained with a milling time 120 minutes with the best concentration of PEG 400 150 wt. %. The average particle size of the as-prepared suspension is 584 nm after addition of acetic acid solution (1%, v/v). Beads milling process did not change the glucosamine and N-acetylglucosamine content on chitosan structure which is indicated by degree of deacetylation higher than 70%. It was concluded that beads milling process can be applied to prepare chitosan fineparticles by proper adjustment in the milling time, pH and dosage of dispersing agent.

Investigation of the milling-induced thermal behavior of crystalline and amorphous griseofulvin.

Science.gov (United States)

Trasi, Niraj S; Boerrigter, Stephan X M; Byrn, Stephen Robert

2010-07-01

To gain a better understanding of the physical state and the unusual thermal behavior of milled griseofulvin. Griseofulvin crystals and amorphous melt quench samples were milled in a vibrating ball mill for different times and then analyzed using differential scanning calorimetry (DSC) and powder X-ray diffraction (PXRD). Modulated DSC (mDSC) and annealing studies were done for the milled amorphous samples to further probe the effects of milling. Milling of griseofulvin crystals results in decrease in crystallinity and amorphization of the compound. A double peak is seen for crystallization in the DSC, which is also seen for the milled melt quench sample. Both enthalpy and temperature of crystallization decrease for the milled melt quenched sample. Tg is visible under the first peak with the mDSC, and annealing shows that increasing milling time results in faster crystallization upon storage. Milling of griseofulvin results in the formation of an amorphous form and not a mesophase. It increases the amount of surface created and the overall energy of the amorphous griseofulvin, which leads to a decreased temperature of crystallization. The two exotherms in the DSC are due to some particles having nuclei on the surface.

Trend and current practices of palm oil mill effluent polishing: Application of advanced oxidation processes and their future perspectives.

Science.gov (United States)

Bello, Mustapha Mohammed; Abdul Raman, Abdul Aziz

2017-08-01

Palm oil processing is a multi-stage operation which generates large amount of effluent. On average, palm oil mill effluent (POME) may contain up to 51, 000 mg/L COD, 25,000 mg/L BOD, 40,000 TS and 6000 mg/L oil and grease. Due to its potential to cause environmental pollution, palm oil mills are required to treat the effluent prior to discharge. Biological treatments using open ponding system are widely used for POME treatment. Although these processes are capable of reducing the pollutant concentrations, they require long hydraulic retention time and large space, with the effluent frequently failing to satisfy the discharge regulation. Due to more stringent environmental regulations, research interest has recently shifted to the development of polishing technologies for the biologically-treated POME. Various technologies such as advanced oxidation processes, membrane technology, adsorption and coagulation have been investigated. Among these, advanced oxidation processes have shown potentials as polishing technologies for POME. This paper offers an overview on the POME polishing technologies, with particularly emphasis on advanced oxidation processes and their prospects for large scale applications. Although there are some challenges in large scale applications of these technologies, this review offers some perspectives that could help in overcoming these challenges. Copyright © 2017 Elsevier Ltd. All rights reserved.

Partial amorphization of an α-FeCr alloy by ball-milling

International Nuclear Information System (INIS)

Loureiro, J. M.; Costa, B. F. O.; Caer, G. Le; Delcroix, P.

2008-01-01

The structural changes of near-equiatomic α-FeCr alloys, ground in a vibratory mill in vacuum and in argon, were followed as a function of milling time. An amorphous phase forms in both cases but at a much faster rate when milling in argon than when milling in vacuum. Amorphisation by ball-milling of α-FeCr alloys is deduced to be an intrinsic phenomenon which is however speeded-up by oxygen. The amorphous phase crystallizes into a bcc Cr-rich phase and a bcc Fe-rich phase when annealed for short times.

Effect of kernel size and mill type on protein, milling yield, and baking quality of hard red spring wheat

Science.gov (United States)

Optimization of flour yield and quality is important in the milling industry. The objective of this study was to determine the effect of kernel size and mill type on flour yield and end-use quality. A hard red spring wheat composite sample was segregated, based on kernel size, into large, medium, ...

Investigations on d.c. conductivity behaviour of milled carbon fibre ...

Indian Academy of Sciences (India)

This paper reports the d.c. conductivity behaviour of milled carbon fibre reinforced polysulphide modified epoxy gradient composites. Milled carbon fibre reinforced composites having 3 vol. % of milled carbon fibre and poly sulphide modified epoxy resin have been developed. D.C. conductivity measurements are conducted ...

21 CFR 515.11 - Supplemental medicated feed mill license applications.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Supplemental medicated feed mill license... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Applications § 515.11 Supplemental medicated feed mill license applications. (a) After approval of a medicated feed...

Preparation of tungsten-iron carbide by ball milling

International Nuclear Information System (INIS)

Wang, G.M.; Campbell, S.J.; Calka, A.; Kaczmarek, W.A.

1996-01-01

Several sets of elemental powder mixtures of Fe-W-C (W 46 Fe 46 C 8 , W 60 Fe 20 C 20 and W 34 Fe 33 C 33 ) were ball milled using Uni-Ball mill for periods of up to 550 h in vacuum with a ball - to - powder ratio of about 35:1. Depending on the milling time, the main component of the as-milled materials was found to be solid solutions of Fe-W-C or Fe-C. Ternary phase W 3 Fe 3 C was obtained on annealing the as-milled materials at about 700 deg C. This product was then found to transfer to (FeW) 6 C on heat treatment at about 800 deg C. The resultant products of the annealing processes were found to depend not only on the annealing temperature, but also the starting composition, especially the initial carbon concentration. Detailed information on the structural and phase evolution during thermal treatment as measured using x-ray diffraction, Moessbauer spectroscopy and thermal analysis is presented. Special interest is focused on the competition for formation in this system between the Fe-C, W-Fe and W-C phases

CO2 laser milling of hard tissue

Science.gov (United States)

Werner, Martin; Ivanenko, Mikhail; Harbecke, Daniela; Klasing, Manfred; Steigerwald, Hendrik; Hering, Peter

2007-02-01

Drilling of bone and tooth tissue belongs to recurrent medical procedures (screw- and pin-bores, bores for implant inserting, trepanation etc.). Small round bores can be in general quickly produced with mechanical drills. Problems arise however by angled drilling, by the necessity to fulfill the drilling without damaging of sensitive soft tissue beneath the bone, or by the attempt to mill precisely noncircular small cavities. We present investigations on laser hard tissue "milling", which can be advantageous for solving these problems. The "milling" is done with a CO2 laser (10.6 μm) with pulse duration of 50 - 100 μs, combined with a PC-controlled galvanic beam scanner and with a fine water-spray, which helps to avoid thermal side-effects. The damaging of underlying soft tissue can be prevented through control of the optical or acoustical ablation signal. The ablation of hard tissue is accompanied with a strong glowing, which is absent during the laser beam action on soft tissue. The acoustic signals from the diverse tissue types exhibit distinct differences in the spectral composition. Also computer image analysis could be a useful tool to control the operation. Laser "milling" of noncircular cavities with 1 - 4 mm width and about 10 mm depth is particularly interesting for dental implantology. In ex-vivo investigations we found conditions for fast laser "milling" of the cavities without thermal damage and with minimal tapering. It included exploration of different filling patterns (concentric rings, crosshatch, parallel lines and their combinations), definition of maximal pulse duration, repetition rate and laser power, optimal position of the spray. The optimized results give evidences for the applicability of the CO2 laser for biologically tolerable "milling" of deep cavities in the hard tissue.

Machining NiTi micro-parts by micro-milling

International Nuclear Information System (INIS)

Weinert, K.; Petzoldt, V.

2008-01-01

The machinability of NiTi by milling has been examined using solid carbide end milling cutters. First results were obtained from machining simple slots applying TiAlN-coated tools with a diameter of 0.4 mm. The machining process was evaluated in terms of tool wear, cutting forces and machining quality. The tool wear and work piece quality was analysed with a scanning electron microscope and a white-light confocal microscope. Despite the poor machinability of NiTi good results concerning tool wear and shape accuracy of the milled slots were achieved. Essential for a good machining result is the application of minimum quantity lubrication. This clearly reduces NiTi adherences compared to dry machining. Work piece quality is improved and tool life is extended. Based on these results different structures could be produced by micro-milling

Towards the effective tool wear control in micro-EDM milling

DEFF Research Database (Denmark)

Bissacco, Giuliano; Valentincic, J.; Hansen, Hans Nørgaard

2010-01-01

The electrode wear in micro-electrical discharge milling (micro-EDM milling) is one of the main problems to be solved in order to improve machining accuracy. This paper presents an investigation on wear and material removal in micro-EDM milling for selected process parameter combinations typical...... of the accuracy of volume measurements on the electrode wear per discharge and on the material removal per discharge are discussed, and the issues limiting the applicability of real time wear sensing in micro-EDM milling are presented....

Massive Yang-Mills fields in the Kemmer's formulation

International Nuclear Information System (INIS)

Santana Cordolino, L.A. de.

1984-01-01

The Kemmer's equation, which describes the meson, is presented in the field theory formalism. Conservated, quantities are found through the Noether's identity. This formalism is used for masive Yang-Mills fields and two equations, similar to the Kemmer's equation, are obtained, although of different formates, both containing quadratic terms. In consequence two Lagrangians are defined, formally distint, for the Yang-Mills fields. The Schroedinger-like Hamiltonian is calculated for the first wave equations. This Hamiltonian presentes one spin-Yang-Mills field interaction term, PHI jk . (L.C.) [pt

Tungsten-nanodiamond composite powders produced by ball milling

Energy Technology Data Exchange (ETDEWEB)

Nunes, D., E-mail: daniela.nunes@ist.utl.pt [Associacao Euratom/IST, Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); ICEMS, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Livramento, V. [Associacao Euratom/IST, Instituto de Plasmas e Fusao Nuclear, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); Mardolcar, U.V. [Departamento de Fisica, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Centro de Ciencias Moleculares e Materiais, Faculdade de Ciencias da Universidade de Lisboa, Campo Grande, 1749-016 Lisboa (Portugal); Correia, J.B. [LNEG, Estrada do Paco do Lumiar, 1649-038 Lisboa (Portugal); Carvalho, P.A. [ICEMS, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Departamento de Bioengenharia, Instituto Superior Tecnico, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)

2012-07-15

The major challenge in producing tungsten-nanodiamond composites by ball milling lies in successfully dispersing carbon nanoparticles in the metallic matrix while keeping carbide formation at a minimum. Processing windows for carbide minimization have been established through systematic variation of the nanodiamond fraction, milling energy and milling time. Materials characterization has been carried out by X-ray diffraction, scanning and transmission electron microscopy and microhardness testing. Nanostructured matrices with homogeneously dispersed particles that preserved the diamond structure have been produced. Differential thermal analysis has been used to evaluate the composites thermal stability.

Ferromagnetic behavior of nanocrystalline Cu–Mn alloy prepared by ball milling

Energy Technology Data Exchange (ETDEWEB)

Mondal, B.N., E-mail: bholanath_mondal@yahoo.co.in [Department of Central Scientific Services, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700 032 (India); Sardar, G. [Department of Zoology, Baruipur College, South 24 parganas 743 610 (India); Nath, D.N. [Department of Physical Chemistry, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700 032 (India); Chattopadhyay, P.P. [Department of Metallurgy and Materials Engineering, Bengal Engineering and Science University, Shibpur, Howrah 711 103 (India)

2014-12-15

50Cu–50Mn (wt%) alloy was produced by ball milling. The milling was continued up to 30 h followed by isothermal annealing over a four interval of temperature from 350 to 650 °C held for 1 h. Crystallite size, lattice strain, lattice parameter were determined by Rietveld refinement structure analysis of X-ray diffraction data. The amount of dissolved/precipitated Mn (wt%) after ball milling/milling followed by annealing was calculated by quantative phase analysis (QPA). The increase of coercivity could be attributed to the introduction of lattice strain and reduction of crystallite size as a function of milling time. Electron paramagnetic resonance and superconducting quantum interface device analysis indicate that soft ferromagnetic behavior has been achieved by ball milled and annealed Cu–Mn alloy. The maximum coercivity value of Cu–Mn alloy obtained after annealing at 350 °C for 1 h is 277 Oe. - Highlights: • A small amount of Mn has dissolved in Cu after ball milling for 30 h. • Coercivity of the Cu–Mn alloy has increased with an increase in milling time. • Substantial MnO has formed after annealing at 650 °C for 1 h. • The ball milled and annealed alloy have revealed soft ferromagnetic behavior. • The alloy annealed at 350 °C shows the maximum value of coercivity.

Integrated chemical plants at the pulp mill

Energy Technology Data Exchange (ETDEWEB)

Ehtonen, P.; Hurme, M.; Jaervelaeinen, M.

1995-12-31

The goal of this paper is to present how the chemical plants can be integrated to the pulp mill. The integration renders possible to balance the chemical consumptions. The total mass balance of a pulp mill with the incoming fuel material and the outgoing waste and flue gases are discussed. The balance figures are presented for the chemicals of the modern fibre line, which will produce fully bleached softwood pulp with an improved effluent quality. The main benefits are lower chemical and transportation costs. The principal over-all plant process block diagrams and process descriptions are presented. The presented info system provides real time information on process and production status at overall mill and department levels. (author)

Structural and magnetic properties of ball milled copper ferrite

DEFF Research Database (Denmark)

Goya, G.F.; Rechenberg, H.R.; Jiang, Jianzhong

1998-01-01

The structural and magnetic evolution in copper ferrite (CuFe2O4) caused by high-energy ball milling are investigated by x-ray diffraction, Mössbauer spectroscopy, and magnetization measurements. Initially, the milling process reduces the average grain size of CuFe2O4 to about 6 nm and induces....... The canted spin configuration is also suggested by the observed reduction in magnetization of particles in the blocked state. Upon increasing the milling time, nanometer-sized CuFe2O4 particles decompose, forming alpha-Fe2O3 and other phases, causing a further decrease of magnetization. After a milling time...... of 98 h, alpha-Fe2O3 is reduced to Fe3O4, and magnetization increases accordingly to the higher saturation magnetization value of magnetite. Three sequential processes during high-energy ball milling are established: (a) the synthesis of partially inverted CuFe2O4 particles with a noncollinear spin...

Parametric Study of End Milling Glass Fibre Reinforced Composites

International Nuclear Information System (INIS)

Azmi, Azwan I.; Lin, Richard J. T.; Bhattacharyya, Debes

2011-01-01

This paper discusses the application of Taguchi 'Design of Experiment' method to investigate the effects of end milling parameters on machinability characteristics of unidirectional E-glass fibre reinforced polymer (GFRP) composites. A series of milling experiments were conducted using tungsten carbide end milling cutters at various spindle speeds, feed rates and depths of cut. Taguchi analysis was carried out and the signal to noise (S/N) ratio with analysis of variance (ANOVA) was employed to analyse the effects of those parameters on GFRP machinability. Overall, the results of the current investigations present some desirable combinations of the machining parameters that can further enhance the end milling machinability characteristics to suit the final requirements of the finished GFRP products.

Uranium mill tailings and radon

International Nuclear Information System (INIS)

Hanchey, L.A.

1981-01-01

The major health hazard from uranium mill tailings is presumed to be respiratory cancer resulting from the inhalation of radon daughter products. A review of studies on inhalation of radon and its daughters indicates that the hazard from the tailings is extremely small. If the assumptions used in the studies are correct, one or two people per year in the US may develop cancer as a result of radon exhaled from all the Uranium Mill Tailings Remedial Action Program sites. The remedial action should reduce the hazard from the tailings by a factor of about 100

Uranium mill tailings and radon

Energy Technology Data Exchange (ETDEWEB)

Hanchey, L A

1981-04-01

The major health hazard from uranium mill tailings is presumed to be respiratory cancer resulting from the inhalation of radon daughter products. A review of studies on inhalation of radon and its daughters indicates that the hazard from the tailings is extremely small. If the assumptions used in the studies are correct, one or two people per year in the United States may develop cancer as a result of radon exhaled from all the Uranium Mill Tailings Remedial Action program sites. The remedial action should reduce the hazard from the tailings by a factor of about 100.

Uranium mill tailings and radon

Energy Technology Data Exchange (ETDEWEB)

Hanchey, L A

1981-01-01

The major health hazard from uranium mill tailings is presumed to be respiratory cancer resulting from the inhalation of radon daughter products. A review of studies on inhalation of radon and its daughters indicates that the hazard from the tailings is extremely small. If the assumptions used in the studies are correct, one or two people per year in the US may develop cancer as a result of radon exhaled from all the Uranium Mill Tailings Remedial Action Program sites. The remedial action should reduce the hazard from the tailings by a factor of about 100.

Anticipated radiological impacts from the mining and milling of thorium for the nonproliferative fuels

International Nuclear Information System (INIS)

Meyer, H.R.; Till, J.E.

1978-01-01

Recent emphasis on proliferation-resistant fuel cycles utilizing thorium--uranium-233 fuels has necessitated evaluation of the potential radiological impact of mining and milling thorium ore. Therefore, an analysis has been completed of hypothetical mine-mill complexes using population and meteorological data representative of a thorium resource site in the Lemhi Pass area of Idaho/Montana, United States of America. Source terms for the site include thorium-232 decay chain radionuclides suspended as dusts and radon-220 and daughters initially released as gas. Fifty-year dose commitments to maximally exposed individuals of 2.4 mrem to total body, 9.5 mrem to bone, and 35 mrem to lungs are calculated to result from facility operation. Radium-228, thorium-228, thorium-232 and lead-212 (daughter of radon-220) are found to be the principal contributors to dose. General population doses for a 50-mile radius surrounding the facility are estimated to be 0.05 man-rem to total body, 0.1 man-rem to bone, and 0.7 man-rem to lungs. Generally speaking, the results of this study indicate that the radiological aspects of thorium mining and milling should pose no significant problems with regard to implementation of thorium fuel cycles

Defect induced electronic states and magnetism in ball-milled graphite.

Science.gov (United States)

Milev, Adriyan; Dissanayake, D M A S; Kannangara, G S K; Kumarasinghe, A R

2013-10-14

The electronic structure and magnetism of nanocrystalline graphite prepared by ball milling of graphite in an inert atmosphere have been investigated using valence band spectroscopy (VB), core level near-edge X-ray absorption fine structure (NEXAFS) spectroscopy and magnetic measurements as a function of the milling time. The NEXAFS spectroscopy of graphite milled for 30 hours shows simultaneous evolution of new states at ~284.0 eV and at ~290.5 eV superimposed upon the characteristic transitions at 285.4 eV and 291.6 eV, respectively. The modulation of the density of states is explained by evolution of discontinuities within the sheets and along the fracture lines in the milled graphite. The magnetic measurements in the temperature interval 2-300-2 K at constant magnetic field strength show a correlation between magnetic properties and evolution of the new electronic states. With the reduction of the crystallite sizes of the graphite fragments, the milled material progressively changes its magnetic properties from diamagnetic to paramagnetic with contributions from both Pauli and Curie paramagnetism due to the evolution of new states at ~284 and ~290.5 eV, respectively. These results indicate that the magnetic behaviour of ball-milled graphite can be manipulated by changing the milling conditions.

Lupine protein enrichment by milling and electrostatic separation

NARCIS (Netherlands)

Wang, Jue; Zhao, Jun; Wit, De Martin; Boom, Remko M.; Schutyser, Maarten A.I.

2016-01-01

Lupine seeds are excellent source of plant protein. We here report on dry fractionation by combining milling and electrostatic separation providing an alternative to wet extraction of protein from lupine seeds. Relatively coarse milling was preferred as this provides sufficient detached protein

The influence of milling on the dissolution performance of simvastatin

DEFF Research Database (Denmark)

Zimper, Ulrike; Aaltonen, Jaakko; Krauel-Goellner, Karen

2012-01-01

properties such as solubility and dissolution rate and, therefore, process induced solid state modifications need to be monitored. The aim of this study was two-fold: firstly, to investigate the dissolution rates of milled and unmilled simvastatin; and secondly, to screen for the main milling factors......, as well as factor interactions in a dry ball milling process using simvastatin as model drug, and to optimize the milling procedure with regard to the opposing responses particle size and process induced disorder by application of a central composite face centered design. Particle size was assessed...... by scanning electron microscopy (SEM) and image analysis. Process induced disorder was determined by partial least squares (PLS) regression modeling of respective X-ray powder diffractograms (XRPD) and Raman spectra. Valid and significant quadratic models were built. The investigated milling factors were...

Crystallization degree change of expanded graphite by milling and annealing

International Nuclear Information System (INIS)

Tang Qunwei; Wu Jihuai; Sun Hui; Fang Shijun

2009-01-01

Expanded graphite was ball milled with a planetary mill in air atmosphere, and subsequently thermal annealed. The samples were characterized by using X-ray diffraction spectroscopy (XRD), scanning electron microscopy (SEM) and thermal gravimetric analysis (TGA). It was found that in the milling initial stage (less than 12 h), the crystallization degree of the expanded graphite declined gradually, but after milling more than 16 h, a recrystallization of the expanded graphite toke place, and ordered nanoscale expanded graphite was formed gradually. In the annealing initial stage, the non-crystallization of the graphite occurred, but, beyond an annealing time, recrystallizations of the graphite arise. Higher annealing temperature supported the recrystallization. The milled and annealed expanded graphite still preserved the crystalline structure as raw material and hold high thermal stability.

Remedial action plan and site conceptual design for stabilization of the inactive uranium mill tailings sites at Rifle, Colorado. Appendix D, Final report

International Nuclear Information System (INIS)

1992-02-01

This appendix assesses the present conditions and data gathered about the two designated inactive uranium mill tailings sites near Rifle, Colorado, and the proposed disposal site six miles north of Rifle in the area of Estes Gulch. It consolidates available engineering, radiological, geotechnical, hydrological, meteorological, and other information pertinent to the design of the Remedial Action Plan (RAP). The data characterize conditions at the mill, tailings, and disposal site so that the Remedial Action Contractor (RAC) may complete final designs for the remedial actions

Remedial action plan and site conceptual design for stabilization of the inactive uranium mill tailings sites at Rifle, Colorado. Appendix D, Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-02-01

This appendix assesses the present conditions and data gathered about the two designated inactive uranium mill tailings sites near Rifle, Colorado, and the proposed disposal site six miles north of Rifle in the area of Estes Gulch. It consolidates available engineering, radiological, geotechnical, hydrological, meteorological, and other information pertinent to the design of the Remedial Action Plan (RAP). The data characterize conditions at the mill, tailings, and disposal site so that the Remedial Action Contractor (RAC) may complete final designs for the remedial actions.

Uranium Mill Tailings Remedial Action Project 1993 Environmental Report

Energy Technology Data Exchange (ETDEWEB)

1994-10-01

This annual report documents the Uranium Mill Tailing Remedial Action (UMTRA) Project environmental monitoring and protection program. The UMTRA Project routinely monitors radiation, radioactive residual materials, and hazardous constituents at associated former uranium tailings processing sites and disposal sites. At the end of 1993, surface remedial action was complete at 10 of the 24 designated UMTRA Project processing sites. In 1993 the UMTRA Project office revised the UMTRA Project Environmental Protection Implementation Plan, as required by the US DOE. Because the UMTRA Project sites are in different stages of remedial action, the breadth of the UMTRA environmental protection program differs from site to site. In general, sites actively undergoing surface remedial action have the most comprehensive environmental programs for sampling media. At sites where surface remedial action is complete and at sites where remedial action has not yet begun, the environmental program consists primarily of surface water and ground water monitoring to support site characterization, baseline risk assessments, or disposal site performance assessments.

Uranium Mill Tailings Remedial Action Project 1993 Environmental Report

International Nuclear Information System (INIS)

1994-10-01

This annual report documents the Uranium Mill Tailing Remedial Action (UMTRA) Project environmental monitoring and protection program. The UMTRA Project routinely monitors radiation, radioactive residual materials, and hazardous constituents at associated former uranium tailings processing sites and disposal sites. At the end of 1993, surface remedial action was complete at 10 of the 24 designated UMTRA Project processing sites. In 1993 the UMTRA Project office revised the UMTRA Project Environmental Protection Implementation Plan, as required by the US DOE. Because the UMTRA Project sites are in different stages of remedial action, the breadth of the UMTRA environmental protection program differs from site to site. In general, sites actively undergoing surface remedial action have the most comprehensive environmental programs for sampling media. At sites where surface remedial action is complete and at sites where remedial action has not yet begun, the environmental program consists primarily of surface water and ground water monitoring to support site characterization, baseline risk assessments, or disposal site performance assessments

Cleaning up commingled uranium mill tailings: is Federal assistance necessary

International Nuclear Information System (INIS)

1979-01-01

GAO was asked to determine whether Federal assistance should be given to operating mill owners that have processed uranium for sale to both government and industry and, thus, generated residual radioactive wastes. The wastes generated for both government and commercial use are called commingled uranium mill tailings. GAO recommends that the Congress provide assistance to active mill owners to share in the cost of cleaning up that portion of the tailings which were produced under Federal contract. Further, GAO believes that the Congress should also consider having the Federal government assist those mills who acted in good faith in meeting all legal requirements pertaining to controlling the mill tailings that were generated for commercial purposes and for which the Federal government is now requiring retroactive remedial action. At the same time, the Congress should make sure that this action establishes no precedent for the Federal government assuming the financial responsibility of cleaning up other non-Federal nuclear facilities and wastes, including those mill tailings generated after the date when the Federal government notified industry that the failings should be controlled

Interacting fields of arbitrary spin and N > 4 supersymmetric self-dual Yang-Mills equations

International Nuclear Information System (INIS)

Devchand, Ch.; Ogievetsky, V.

1996-06-01

We show that the self-dual Yang-Mills equations afford supersymmetrization to systems of equations invariant under global N-extended super-Poincare transformations for arbitrary values of N, without the limitation (N ≤ 4) applicable to standard non-self-dual Yang-Mills theories. These systems of equations provide novel classically consistent interactions for vector supermultiplets containing fields of spin up to N-2/2. The equations of motion of the component fields of spin greater than 1/2 are interacting variants of the first-order Dirac-Fierz equations for zero rest-mass fields of arbitrary spin. The interactions are governed by conserved currents which are constructed by an iterative procedure. In (arbitrarily extended) chiral superspace, the equations of motion for the (arbitrarily large) self-dual supermultiplet are shown to be completely equivalent to the set of algebraic supercurvature defining the self-dual superconnection. (author). 25 refs

Nanostructured Al/Al4C3 composites reinforced with graphite or fullerene and manufactured by mechanical milling and spark plasma sintering

International Nuclear Information System (INIS)

Robles Hernández, F.C.; Calderon, H.A.

2012-01-01

Highlights: ► Fullerene mix (C 60 + C 70 + soot) is effective to manufacture nanostructured Al/Al 4 C 3 . ► Carbon in the fullerene mix is more reactive with Al that that present in graphite. ► A complete transformation of carbon into Al 4 C 3 is observed in the Al/fullerene. ► Milling and sintering conditions preserve the nanostructured nature of the composites. ► Hardness improvement: 375% Al/graphite and 582% for Al/fullerene composites. - Abstract: Nanostructured Al matrix composites with reinforcements of graphite or fullerene (C 60 + C 70 + soot) have been produced by mechanical milling and spark plasma sintering (SPS). X-ray diffraction and transmission electron microscopy show that C 60 + C 70 withstand longer mechanical milling/alloying times than graphite. Fullerene is a good control agent during mechanical alloying resulting in a denser Al/fullerene composite when compared to the Al/graphite one. A refinement mechanism that takes place during mechanical alloying of fullerene and graphite is experimentally found and correspondingly discussed. Such a mechanism plays a major role in the amorphization of graphite. The larger surface area of the fullerene mix after milling promotes a better interaction with Al and hence allows its complete transformation into Al 4 C 3 during the SPS process. The sintered products show an increase in hardness for the Al/fullerene composite of 6 times and only 4 times for the Al/graphite composite. The SPS technique shows to be an excellent method to transform the fullerene into Al 4 C 3 while preserving its nanostructured nature.

Children's Rights, "die Antipadagogen," and the Paternalism of John Stuart Mill.

Science.gov (United States)

Nordenbo, Sven Erik

1989-01-01

Examines how John Stuart Mill would have viewed present-day educational liberalists' claims that children should be included in Mill's principle of individual liberty. Concludes that educational liberalists cannot rightly claim Mill as spokesman for their views. (KO)

Lab-scale roller table mill for investigating the grinding behaviour of coal

Energy Technology Data Exchange (ETDEWEB)

Werner, V.; Zelkowski, J.; Schoenert, K. [Inst. for Energy Process Engineering and Fuel Technology and Inst. of Mineral Processing, Univ. Clausthal, Clausthal-Zellerfeld (Germany)

1999-11-01

The test mill is equipped with one roller. The material bed can be discharged completely after overroling. Grinding force, torque and gap width are measured. Cycle tests with three coals have been performed for simulating a closed circuit process. The grinding behaviour is characterized by the following relations: compaction of the particle bed and specific power draft vs. specific grinding force, production of fine material (dust), circuit factor, specific surface of the dust and specific work-input of the grinding circuit vs. specific power draft. (orig.)

Reclamation from palm oil mill effluent using an integrated zero discharge membrane-based process

Directory of Open Access Journals (Sweden)

Ahmad A.L.

2015-12-01

Full Text Available This research emphasizes eloquently on membrane technology for treatment of palm oil mill effluent (POME as it is the Malaysia’s largest and most important agro based industry. Findings established significant quality improvement with an efficient recovery of water from palm oil mill via innovative membrane application. Conventional bio-methods, whilst adhering to the Department of Environment’s (DOE discharge regulations, produces brownish liquid which pales in comparison to the crystal clear water obtained through membrane treatment. The pre-treatment process consists of coagulation-flocculation using green environmental coagulant bases such as Moringa oleifera (MO seeds. The ultrafiltration polyvinylidene difluoride (PVDF and thin film composite (TFC reverse osmosis were vital for the membrane processes. The system gave 99% suspended solids reduction in suspended solid and 78% of water present was successfully recovered. This technology guarantees water recovery with drinking water quality; meeting the US Environmental Protection Agency (USEPA standard or could be recycled into the plant with sludge utilization for palm oil estates, thus enabling the concept of zero discharge to be executed in the industries. In addition, green and healthy antioxidants such as oil and beta-carotene can be recovered from POME further demonstrate. Silica gel showed better performance in separation of carotenes from oil at temperature 40°C using adsorption chromatography with 1154.55 ppm. The attractiveness of this technology, enabling the utilization of reuse of agricultural waste into potentially value added products.

Baseline risk assessment for groundwater contamination at the uranium mill tailings site near Monument Valley, Arizona. Draft

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

This baseline risk assessment evaluates potential impact to public health or the environment resulting from groundwater contamination at the former uranium mill processing site near Monument Valley, Arizona. The tailings and other contaminated material at this site are being relocated and stabilized in a disposal cell at Mexican Hat, Utah, through the US Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project. The tailings removal is planned for completion by spring 1994. After the tailings are removed, groundwater contamination at the site will continue to be evaluated. This risk assessment is the first document specific to this site for the Groundwater Project. It will be used to assist in determining what remedial action is needed for contaminated groundwater at the site.

Releases of radioactivity from uranium mills and effluent treatment costs

International Nuclear Information System (INIS)

Witherspoon, J.P.; Sears, M.B.; Blanco, R.E.

1977-01-01

Airborne releases of radioactive materials from uranium milling to the environment consist of ore dust, yellowcake dust, tailings dust, and radon gas while the mill is active. After a mill has ceased operations, tailings may be stabilized to minimize or prevent airborne releases of radioactive particulates. However, radon gas will continue to be released in amounts inversely proportional to the degree of stabilization treatment (and expense). Liquid waste disposal is by evaporation and natural seepage to the ground beneath the tailings impoundment area. The release of radioactive materials (and potential radiation exposures) determines the majority of costs associated with minimizing the environmental impact of uranium milling. Radwaste treatments to reduce estimated radiation doses to individuals to 3 to 5% of those received with current milling practices are equivalent to $0.66 per pounds of U 3 O 8 and 0.032 mill per kWhr of electricity. This cost would cover a high efficiency reverse jet bag filter and high energy venturi scrubbers for dusts, neutralization of liquids, and an asphalt-lined tailings basin with a clay core dam to reduce seepage. In addition, this increased cost would cover stabilization of tailings, after mill closure, with a 1-in. asphalt membrane topped by 2 ft of earth and 0.5 ft of crushed rock to provide protection against future leaching and wind erosion. The cost of reducing the radiological hazards associated with uranium milling to this degree would contribute about 0.4% to the current total cost of nuclear power

Chest radiological findings in pakistani cement mill workers

International Nuclear Information System (INIS)

Meo, Sultan A.

2003-01-01

Chest radiological findings in Pakistani cement mill workers Even in the 21st century, in developing countries millions of people work daily in dusty environments. They are exposed to different types of health hazards namely, fumes, gases and dust, which are risk factors for developing occupational diseases. Therefore, the aim of this study was to perform chest radiology to determine the occupational hazards of cement dust on the lungs of cement mill workers. This study was carried out in the Department of Physiology, Faculty of Health and Medical Sciences, Hamdard University Karachi, Pakistan, during the period June to August 2000. In this study 50, apparently healthy volunteer male cement mill workers were randomly selected with an average of 13 years exposure with age ranging from 20-60 years. They were matched with 50, healthy male control subjects in terms of age, height, weight and socioeconomic status. Both groups met with exclusion criteria as per standard. Radiology was performed by Trophy radiology. Results: The present study demonstrated 12% of cases with interstitial lung disease and 2% of cases with pleural thickening and chronic bronchitis in cement mill workers. Conclusion: Exposure to cement dust causes interstitial lung disease, pleural thickening and chronic bronchitis in cement mill workers. (author)

Development of a National Center for Hydrogen Technology. A Summary Report of Activities Completed at the National Center for Hydrogen Technology - Year 6

Energy Technology Data Exchange (ETDEWEB)

Holmes, Michael [Univ. of North Dakota, Grand Forks, ND (United States)

2012-08-01

The Energy & Environmental Research Center (EERC) located in Grand Forks, North Dakota, has operated the National Center for Hydrogen Technology (NCHT) since 2005 under a Cooperative Agreement with the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL). The EERC has a long history of hydrogen generation and utilization from fossil fuels, and under the NCHT Program, the EERC has accelerated its research on hydrogen generation and utilization topics. Since the NCHT's inception, the EERC has received more than $65 million in funding for hydrogen-related projects ($24 million for projects in the NCHT, which includes federal and corporate partner development funds) involving more than 85 partners (27 with the NCHT). The NCHT Program's nine activities span a broad range of technologies that align well with the Advanced Fuels Program goals and, specifically, those described in the Hydrogen from Coal Program research, development, and demonstration (RD&D) plan that refers to realistic testing of technologies at adequate scale, process intensification, and contaminant control. A number of projects have been completed that range from technical feasibility of several hydrogen generation and utilization technologies to public and technical education and outreach tools. Projects under the NCHT have produced hydrogen from natural gas, coal, liquid hydrocarbons, and biomass. The hydrogen or syngas generated by these processes has also been purified in many of these instances or burned directly for power generation. Also, several activities are still undergoing research, development, demonstration, and commercialization at the NCHT. This report provides a summary overview of the projects completed in Year 6 of the NCHT. Individual activity reports are referenced as a source of detailed information on each activity.

Comparison between microfabrication technologies for metal tooling

DEFF Research Database (Denmark)

Uriarte, L.; Herrero, A.; Ivanov, A.

2006-01-01

microtechnologies for processing tooling inserts made of metal. The following technologies have been analysed: micromilling, micro-electrodischarge machining (EDM, including wire-EDM, sinking-EDM, and EDM-milling), laser micromachining, electroforming, and electrochemical milling (ECF) (an electrochemical machining...... innovative process proposed by HSG-IMAT). Considered tool-insert materials are nickel for electroforming, stainless steel for ECF, and tool steel (AISI H13) for all other processes. Typical features (ribs, channels, pins, and holes) required by micro-optics, microfluidics, and sensor and actuator...

Gauged supersymmetries in Yang-Mills theory

International Nuclear Information System (INIS)

Tissier, Matthieu; Wschebor, Nicolas

2009-01-01

In this paper we show that Yang-Mills theory in the Curci-Ferrari-Delbourgo-Jarvis gauge admits some up to now unknown local linear Ward identities. These identities imply some nonrenormalization theorems with practical simplifications for perturbation theory. We show, in particular, that all renormalization factors can be extracted from two-point functions. The Ward identities are shown to be related to supergauge transformations in the superfield formalism for Yang-Mills theory. The case of nonzero Curci-Ferrari mass is also addressed.

Tinkering with Technology: A Library Workshop to Support 4-H Youth Development

Science.gov (United States)

Hendrix, Beth; Williamson, Evan

2017-01-01

When University of Idaho (UI) Extension brought the Idaho 4-H Teen Conference to UI's main campus, the conference organizers collaborated with UI librarians to organize a workshop in the library's newly established makerspace, the Making, Innovating, and Learning Laboratory (MILL). In the MILL, the students used cutting-edge technology to foster…

Technologies for the treatment of effluents from uranium mines, mills and tailings. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

2002-06-01

Effluent treatment is an important aspect of uranium mining and milling operations that continues through decommissioning and site rehabilitation. During the life of a mine, effluent treatment is an integral part of the operation with all effluent either being recycled to the mill or processed through a water treatment plant before being released into the environment. During decommissioning and rehabilitation, effluent treatment must continue either through a water treatment plant of by using passive treatment techniques. Because of the recent closing of several uranium mines or mining districts, particularly in eastern Europe, effluent treatment is becoming an ever increasing concern. Therefore the IAEA convened a technical committee meeting (TCM) so that experts from different countries could discuss information and knowledge on effluent treatment processes and methods. The papers presented at the meeting describe techniques for treatment of effluents from uranium production operations - both past and present. This publication contains ten papers presented at the meeting; each of the papers was indexed separately

High-Energy Ball-Milling of Alloys and Compounds

International Nuclear Information System (INIS)

Le Caer, G.; Delcroix, P.; Begin-Colin, S.; Ziller, T.

2002-01-01

After outlining some characteristics of high-energy ball-milling, we discuss selected examples of phase transformation and of alloy synthesis which focus on deviations from archetypal behaviours and throw light on the milling mechanisms. Some contributions of Moessbauer spectrometry to the characterization of ground materials are described.

Degradation of Trichloroethene with a Novel Ball Milled Fe–C Nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Gao, Jie; Wang, Wei [Environmental Sciences Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Rondinone, Adam J. [Center for Nanophase Materials Sciences, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); He, Feng, E-mail: fenghe@zjut.edu.cn [College of Biological and Environmental Engineering, Zhejiang University of Technology, Hangzhou, Zhejiang 310032 (China); Liang, Liyuan [Environmental Sciences Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States)

2015-12-30

Highlights: • Novel, inexpensive iron–carbon (Fe–C) nanocomposite was obtained by milling. • Fe–C instantaneously sorbed >90% of trichloroethene and continuously degraded them. • The carbon reduced the generation of C{sub 3}−C{sub 6} intermediates and mainly produced C{sub 2}H{sub 4}. • Fe–C can attach to the DNAPL phase thus enhancing degradation efficiency. - Abstract: Nanoscale zero-valent iron (NZVI) is effective in reductively degrading dense non-aqueous phase liquids (DNAPLs), such as trichloroethene (TCE), in groundwater (i.e., dechlorination) although the NZVI technology itself still suffers from high material costs and inability to target hydrophobic contaminants in source zones. To address these problems, we developed a novel, inexpensive iron–carbon (Fe–C) nanocomposite material by simultaneously milling micron-size iron and activated carbon powder. Microscopic and X-ray diffraction (XRD) characterization of the composite material revealed that nanoparticles of Fe were dispersed in activated carbon and a new iron carbide phase was formed. Bench-scale studies showed that this material instantaneously sorbed >90% of TCE from aqueous solutions and subsequently decomposed TCE into non-chlorinated products. Compared to milled Fe, Fe–C nanocomposite dechlorinated TCE at a slightly slower rate and favored the production of ethene over other TCE degradation products such as C{sub 3}−C{sub 6} compounds. When placed in hexane-water mixture, the Fe–C nanocomposite materials are preferentially partitioned into the organic phase, indicating the ability of the composite materials to target DNAPL during remediation.

Current practices for the management and confinement of uranium mill tailings

International Nuclear Information System (INIS)

1992-01-01

This report discusses the current practices used in the design siting, construction and closeout of impoundment facilities for uranium mill tailings. The objective is to present an integrated overview of the technological, safety and radiation protection aspects of these topics in order to ensure that the potential radiological and non-radiological risks associated with the management of uranium mill tailings are minimized now and in the future. The report: identifies the nature and source of radioactive and non-radioactive pollutants in uranium mill tailings; identifies the important mechanisms by which pollutants can be released from the tailings impoundment; reviews radiation protection aspects of these mechanisms; describes the pathways by which the pollutants may reach humans; describes some of the site selection and design options and considerations for final stabilization and rehabilitation of tailings impoundments; describes the methods of assessing closure strategies; describes long term responsibilities for tailings management and financial assurance to ensure these responsibilities; and reviews the magnitude and probability of occurrence of the hazards arising, with the aim of ensuring that the risks presented are acceptable. Because of the complexity of the pollutant release mechanisms and the site specific nature of the design and management controls that can be used, it is not possible for a report of this nature to be either exhaustive or detailed in all respects. The methods of confinement employed for any particular tailings impoundment will depend on the country, its climate, demography and its site specific performance criteria which should be defined by the relevant competent authorities. Both operating and post-operating conditions are considered. After shutdown of the mill and stabilization of the tailings, continuing surveillance and maintenance should be considered until the integrity and durability of the tailings impoundment have been

Visual Inspection for Breakage of Micro-milling Cutter

Directory of Open Access Journals (Sweden)

WANG Lei

2014-11-01

Full Text Available In order to realize visual inspection for breakage of micro-milling cutter, a developed image acquisition method of the surface of a micro-milling cutter was constructed and a classification method based on multilayer neural network was proposed in this article. While the milling cutter was rotating at a constant speed, a camera was triggered by a rotary encoder to capture a series of images. And the developed image of milling cutter was created by image mosaic algorithms. The moment of regional feature as well as the gray feature of the tooth edge was extracted as the input vector of neural network. The feature vector includes moment of inertia, geometric central moment, three-dimensional invariants moment and the gray value of the projection on two principal axis directions of the tooth region. By designing a proper neural network, breakage defects can be detected 100 %. And the false discovery rate is 0.5 %.

The Complete Picture: "Standards for Technological Literacy" and "Advancing Excellence in Technological Literacy."

Science.gov (United States)

Technology Teacher, 2003

2003-01-01

Provides an overview of the "Standards for Technological Literacy: Content for the Study of Technology" (STL) and "Advancing Excellence in Technological Literacy: Student Assessment, Professional Development, and Program Standards" (AETL). Shows how the documents work together to advance the technological literacy of technology educators and K-12…

Conformally flat spaces and solutions to Yang-Mills equations

International Nuclear Information System (INIS)

Chaohao, G.

1980-01-01

Using the conformal invariance of Yang-Mills equations in four-dimensional manifolds, it is proved that in a simply connected space of negative constant curvature Yang-Mills equations admit solutions with any real number as their Pontryagin number. It is also shown that the space S 3 x S 1 which is the regular counterpart of the meron solution is one example of a class of solutions to Yang-Mills equations on compact manifolds that are neither self-dual nor anti-self-dual

Response to Thermal Exposure of Ball-Milled Aluminum-Borax Powder Blends

Science.gov (United States)

Birol, Yucel

2013-04-01

Aluminum-borax powder mixtures were ball milled and heated above 873 K (600 °C) to produce Al-B master alloys. Ball-milled powder blends reveal interpenetrating layers of deformed aluminum and borax grains that are increasingly refined with increasing milling time. Thermal exposure of the ball-milled powder blends facilitates a series of thermite reactions between these layers. Borax, dehydrated during heating, is reduced by Al, and B thus generated reacts with excess Al to produce AlB2 particles dispersed across the aluminum grains starting at 873 K (600 °C). AlB2 particles start to form along the interface of the aluminum and borax layers. Once nucleated, these particles grow readily to become hexagonal-shaped crystals that traverse the aluminum grains with increasing temperatures as evidenced by the increase in the size as well as in the number of the AlB2 particles. Ball milling for 1 hour suffices to achieve a thermite reaction between borax and aluminum. Ball milling further does not impact the response of the powder blend to thermal exposure. The nucleation-reaction sites are multiplied, however, with increasing milling time and thus insure a higher number of smaller AlB2 particles. The size of the AlB2 platelets may be adjusted with the ball milling time.

Cosmological coevolution of Yang-Mills fields and perfect fluids

International Nuclear Information System (INIS)

Barrow, John D.; Jin, Yoshida; Maeda, Kei-ichi

2005-01-01

We study the coevolution of Yang-Mills fields and perfect fluids in Bianchi type I universes. We investigate numerically the evolution of the universe and the Yang-Mills fields during the radiation and dust eras of a universe that is almost isotropic. The Yang-Mills field undergoes small amplitude chaotic oscillations, as do the three expansion scale factors which are also displayed by the expansion scale factors of the universe. The results of the numerical simulations are interpreted analytically and compared with past studies of the cosmological evolution of magnetic fields in radiation and dust universes. We find that, whereas magnetic universes are strongly constrained by the microwave background anisotropy, Yang-Mills universes are principally constrained by primordial nucleosynthesis but the bound is comparatively weak with Ω YM rad

Integrated assessmet of the impacts associated with uranium mining and milling

Energy Technology Data Exchange (ETDEWEB)

Parzyck, D.C.; Baes, C.F. III; Berry, L.G.

1979-07-01

The occupational health and safety impacts are assessed for domestic underground mining, open pit mining, and milling. Public health impacts are calculated for a population of 53,000 located within 88 km (55 miles) of a typical southwestern uranium mill. The collective annual dose would be 6.5 man-lung rem/year, 89% of which is from /sup 222/Rn emitted from mill tailings. The dose to the United States population is estimated to be 6 x 10/sup 4/ man-lung rem from combined mining and milling operations. This may be comparedd with 5.7 x 10/sup 5/ man-lung rem from domestic use of natural gas and 4.4 x 10/sup 7/ man-lung rem from building interiors. Unavoidable adverse environmental impacts appear to be severe in a 250 ha area surrounding a mill site but negligible in the entire potentially impacted area (500,000 ha). The contemporary uranium resource and supply industry and its institutional settings are described in relation to the socio-economic impacts likely to emerge from high levels of uranium mining and milling. Radon and radon daughter monitoring techniques associated with uranium mining and milling are discussed.

Integrated assessmet of the impacts associated with uranium mining and milling

International Nuclear Information System (INIS)

Parzyck, D.C.; Baes, C.F. III; Berry, L.G.

1979-07-01

The occupational health and safety impacts are assessed for domestic underground mining, open pit mining, and milling. Public health impacts are calculated for a population of 53,000 located within 88 km (55 miles) of a typical southwestern uranium mill. The collective annual dose would be 6.5 man-lung rem/year, 89% of which is from 222 Rn emitted from mill tailings. The dose to the United States population is estimated to be 6 x 10 4 man-lung rem from combined mining and milling operations. This may be comparedd with 5.7 x 10 5 man-lung rem from domestic use of natural gas and 4.4 x 10 7 man-lung rem from building interiors. Unavoidable adverse environmental impacts appear to be severe in a 250 ha area surrounding a mill site but negligible in the entire potentially impacted area (500,000 ha). The contemporary uranium resource and supply industry and its institutional settings are described in relation to the socio-economic impacts likely to emerge from high levels of uranium mining and milling. Radon and radon daughter monitoring techniques associated with uranium mining and milling are discussed

A survey of present levels of radiocesium in Swedish pulp mill liquors and the implications for wood radiocesium transfer factors. Using Kraft mill liquors as an indicator of wood radiocesium contamination

International Nuclear Information System (INIS)

Ravila, A.; Holm, E.

2000-01-01

A survey was initiated to depict and compare the present activity levels in pulp mill liquors from various mill locations. The 137 Cs levels in pulp mill liquors were compared with the mill location and the deposition pattern of the Chernobyl fallout and nuclear weapons fallout. The large input of wood (about 2500 m 3 per day) to an average Nordic Kraft mill and the relatively long-term retention time for radiocesium in the Kraft mill recovery cycle enables representative sampling of substances directly related to the activity concentration in wood. (author)

78 FR 38877 - Kraft Pulp Mills NSPS Review

Science.gov (United States)

2013-06-28

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 60 [EPA-HQ-OAR-2012-0640] FRL-9829-3 RIN 2060-AR64 Kraft Pulp Mills NSPS Review AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule... comments on the May 23, 2013, proposed rule titled, ``Kraft Pulp Mills NSPS Review'' is being extended by...

Some global charges in classical Yang-Mills theory

International Nuclear Information System (INIS)

Chrus'ciel, P.T.; Kondracki, W.

1987-01-01

Three classes of boundary conditions allowing the definition of a global field strength (''global color'') are presented. A definition of global color of the sources and of the Yang-Mills field is proposed. Some exact solutions of Yang-Mills equations with point sources and with ''topologically nontrivial electric color'' are presented

Effects of milling on the extraction efficiency of incurred pesticides in cereals

DEFF Research Database (Denmark)

Herrmann, Susan Strange; Hajeb, Parvaneh; Andersen, Gitte

2017-01-01

This study investigated the effects of particle size and milling temperature on the extraction efficiencies of pesticide residues from cereal flour. Samples of cereal grains (barley, oat, rye and wheat) were milled using a centrifugal mill with four different sieves (0.2, 1.0, 3.0 and 5.0 mm......) or a knife mill both at room temperature and after freezing of the grain at –80°C overnight. The incurred pesticides in the test materials were extracted by the QuEChERS method and analysed by LC-MS/MS and GC-MS/MS. The particle size distribution for the milled samples was determined using a vibratory sieve...... shaker. Based on the pesticide levels recovered from each of the different millings and the corresponding particle size distributions, it was confirmed that smaller average particle sizes increase the extraction efficiency up to 31%, with all other factors equal. The cereals milled at room temperature...

Recycling and disposal of FUSRAP materials from the Ashland 2 site at a licensed uranium mill

International Nuclear Information System (INIS)

Howard, B.; Conboy, D.; Rehmann, M.; Roberts, H.

1999-01-01

During World War II the Manhattan Engineering District (MED) used facilities near Buffalo, N.Y. to extract natural uranium from ores. Some of the byproduct material left from the ores (MED byproduct), containing low levels of uranium, thorium, and radium, was deposited on a disposal site known as Ashland 2, located in Tonawanda, NY. On behalf of the United States Army Corps of Engineers (USACE, or the Corps), ICF Kaiser Engineers (ICFKE) was tasked to provide the best value clean-up results that meet all of the criteria established in the Record of Decision for the site. International Uranium (USA) Corporation (IUC), the operator of the White Mesa Uranium Mill, a Nuclear Regulatory Commission (NRC)-licensed mill near Blanding, Utah, was selected to perform uranium extraction on the excavated materials, therefore giving the best value as it provided beneficial use of the material consistent with the Resource Conservation and Recovery Act (RCRA) intent to encourage recycling and recovery, while also providing the most cost-effective means of disposal. Challenges overcome to complete this project included (1) identifying the best-value location to accept the material; (2) meeting regulatory requirements with IUC obtaining an NRC license amendment to accept and process the material as an alternate feed; (3) excavating and preparing the material for shipment, then shipping the material to the Mill for uranium recovery; and (4) processing the material, followed by disposal of tailings from the process in the Mill's licensed uranium tailings facility. Excavation from Ashland 2 and processing of the Ashland 2 material at the White Mesa Mill resulted in a cleaner environment at Tonawanda, a cost avoidance of up to $16 million, beneficial recovery of source material, and environmentally protective disposal of byproduct material. (author)

76 FR 70170 - Proposed Alternative Soils Standards for the Uravan, Colorado Uranium Mill

Science.gov (United States)

2011-11-10

..., Colorado Uranium Mill AGENCY: Nuclear Regulatory Commission. ACTION: Uranium milling alternative standards... Agreements to regulate uranium mill tailings (11e.(2) byproduct material). Six Agreement States have this... in Colorado are acceptable. Discussion The Uravan site began operations in 1912 as a radium mill and...

Discrete element method based scale-up model for material synthesis using ball milling

Science.gov (United States)

Santhanam, Priya Radhi

Mechanical milling is a widely used technique for powder processing in various areas. In this work, a scale-up model for describing this ball milling process is developed. The thesis is a combination of experimental and modeling efforts. Initially, Discrete Element Model (DEM) is used to describe energy transfer from milling tools to the milled powder for shaker, planetary, and attritor mills. The rolling and static friction coefficients are determined experimentally. Computations predict a quasisteady rate of energy dissipation, E d, for each experimental configuration. It is proposed that the milling dose defined as a product of Ed and milling time, t, divided by the mass of milled powder, mp characterizes the milling progress independently of the milling device or milling conditions used. Once the milling dose is determined for one experimental configuration, it can be used to predict the milling time required to prepare the same material in any milling configuration, for which Ed is calculated. The concept is validated experimentally for DEM describing planetary and shaker mills. For attritor, the predicted Ed includes substantial contribution from milling tool interaction events with abnormally high forces (>103 N). The energy in such events is likely dissipated to heat or plastically deform milling tools rather than refine material. Indeed, DEM predictions for the attritor correlate with experiments when such events are ignored in the analysis. With an objective of obtaining real-time indicators of milling progress, power, torque, and rotation speed of the impeller of an attritor mill are measured during preparation of metal matrix composite powders in the subsequent portion of this thesis. Two material systems are selected and comparisons made between in-situ parameters and experimental milling progress indicators. It is established that real-time measurements can certainly be used to describe milling progress. However, they need to be interpreted carefully

21 CFR 515.20 - Approval of medicated feed mill license applications.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Approval of medicated feed mill license... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Administrative Actions on Licenses § 515.20 Approval of medicated feed mill license applications. Within 90 days after an...

21 CFR 515.23 - Voluntary revocation of medicated feed mill license.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Voluntary revocation of medicated feed mill... SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS MEDICATED FEED MILL LICENSE Administrative Actions on Licenses § 515.23 Voluntary revocation of medicated feed mill license. A license issued under...

A computer code for the prediction of mill gases and hot air distribution between burners sections as input parameters for 3D CFD furnace calculation

International Nuclear Information System (INIS)

Tucakovic, Dragan; Zivanovic, Titoslav; Beloshevic, Srdjan

2006-01-01

Current computer technology development enables application of powerful software packages that can provide a reliable insight into real operating conditions of a steam boiler in the Thermal Power Plant. Namely, an application of CFD code to the 3D analysis of combustion and heat transfer in a furnace provides temperature, velocity and concentration fields in both cross sectional and longitudinal planes of the observed furnace. In order to obtain reliable analytical results, which corresponds to real furnace conditions, it is necessary to accurately predict a distribution of mill gases and hot air between burners' sections, because these parameters are input values for the furnace 3D calculation. Regarding these tasks, the computer code for the prediction of mill gases and hot air distribution has been developed at the Department for steam boilers of the Faculty of Mechanical Engineering in Belgrade. The code is based on simultaneous calculations of material and heat balances for fan mill and air tracts. The aim of this paper is to present a methodology of performed calculations and results obtained for the steam boiler furnace of 350 MWe Thermal Power Plant equipped with eight fan mills. Key words: mill gases, hot air, aerodynamic calculation, air tract, mill tract.

Superlocalization formulas and supersymmetric Yang-Mills theories

International Nuclear Information System (INIS)

Bruzzo, U.; Fucito, F.

2004-01-01

By using supermanifolds techniques we prove a generalization of the localization formula in equivariant cohomology which is suitable for studying supersymmetric Yang-Mills theories in terms of ADHM data. With these techniques one can compute the reduced partition functions of topological super-Yang-Mills theory with 4, 8 or 16 supercharges. More generally, the superlocalization formula can be applied to any topological field theory in any number of dimensions

Instability of higher dimensional Yang-Mills systems

International Nuclear Information System (INIS)

Randjbar-Daemi, S.; Strathdee, J.

1983-01-01

We investigate the stability of Poincare xO(3) invariant solutions for a pure semi-simple Yang-Mills, as well as Yang-Mills coupled to gravity in 6-dimensional space-time compactified over M 4 xS 2 . In contrast to the Maxwell U(1) theory (IC-82/208) in six dimensions coupled with gravity and investigated previously, the present theory exhibits tachyonic excitations and is unstable. (author)

Corporate Governance of Sugar Mills in East Java: A Transaction Cost Economics Perspective

Directory of Open Access Journals (Sweden)

Ahmad Erani Yustika

2007-01-01

Full Text Available Despite Indonesia’s overall achievements during the past two decades%2C the economy is encountering a series of problems. One of the biggest challenges is the unsatisfactory performance of the state-owned enterprises (SOEs. Subsidisies and uncovered loans to the SOEs have drained the government’s fiscal resources%2C and the signing off of employees creates many social problems. Compared with the SOEs in other sectors%2C state-owned sugar mills face more serious crises which not only jeopardise the social fabric%2C but also endanger the production. Research results strengthen the statement that the basic problem in sugar mills is management inefficiency resulting in high transaction costs. This research compares the transaction costs between state-owned (Ngadiredjo and privately-owned (Kebon Agung sugar mills. The study shows that in Kebon Agung Sugar Mill transaction costs are higher than production costs%2C while in Ngadiredjo Sugar Mill the reverse is true. However%2C the high transaction costs in Kebon Agung Sugar Mill cannot be attributed directly to inefficient institutions%2C because Ngadiredjo Sugar Mill incurred high costs for plants%2C land preparation%2C and fertilizer%2C which decreased the proportion of transaction costs. If analyzed in detail%2C the following facts are revealed: (i market transaction costs in Kebon Agung Sugar Mill are higher than in Ngadiredjo Sugar Mill. This is because Kebon Agung Sugar Mill has established cooperation with sugarcane farmers in the form of extensions and transport subsidies; and (ii the political transaction costs proportion in Ngadiredjo Sugar Mill is higher than in Kebon Agung Sugar Mill because of the imposition of many ‘illegal’ fees. Abstract in Bahasa Indonesia : transaction cost economics%2C corporate governance%2C sugar mill%2C East Java.

Pulp-mill related polychlorinated organic compounds in Baltic Sea sediments

Energy Technology Data Exchange (ETDEWEB)

Jonsson, Per (Swedish Environmental Protection Agency, Solna (Sweden)); Rappe, C.; Kjeller, L.O. (Umeaa Univ. (Sweden). Inst. of Environmental Chemistry); Kierkegaard, A. (Stockholm Univ. (Sweden). Inst. of Applied Environmental Research); Haakansson, L. (Uppsala Univ. (Sweden). Inst. of Earth Sciences); Jonsson, Bjoern (County Adm. Board, Umeaa (Sweden))

1993-01-01

Sediment samples from the Baltic basin were analyzed for PCDD/Fs, alkyl-CDFs, chloroguaiacols and EOCl. The EOCl distribution pattern in the Iggesund pulp-mill area shows high sediment concentrations close to the mill, and decreasing concentrations with increasing distance from the mill. Two series of alkyl-CDFs have been identified. The PCDD/Fs in offshore surficial sediments from the Baltic proper show a typical incineration pattern, while sediments collected in the vicinity of the mill show enhanced levels of 2,3,7,8-tetraCDD, 2,3,7,8- and 1,2,7,8-tetraCDF, and 1,2,3,7,8-pentaCDD. These PCDD/F congeners are statistically correlated to di-, tri-, and tetrachloroguaiacols, alkyl-CDFs, EOCl, and to the distance from the pulp mill, indicating the same source and transportation regime. Principal component analysis of the data set supports this conclusion. The three 2,3,7,8-tetrachloro-substituted PCDD/F congeners have formerly been found in high concentrations in sediments and crab hepatopancreas close to a pulp mill on the Swedish west coast. Our results from a pulp mill on the Swedish east coast support the conclusion that these congeners are typically associated with pulp bleaching. Deep layer sediments have significantly lower levels of PCDD/Fs. The isomer profiles are different in the surficial and the deep sediments, indicating a more natural preindustrial production of PCDD/Fs. (53 refs., 7 figs.).

Crook and overlength in hardwood lumber:results from a 14-mill survey

Science.gov (United States)

Jan Wiedenbeck; John Brown; Neal Bennett

2003-01-01

Data on red oak lumber were collected at 14 furniture and cabinet industry rough mills to identify how crook and overlength are related to lumber grade and size from mill to mill. The amount of crook in a sample of dry, 4/4 thickness, red oak lumber was significantly influenced by lumber grade and length, supply region, and mill. There were no differences in crook...

77 FR 35431 - Final Alternative Soils Standards for the Uravan, CO, Uranium Mill

Science.gov (United States)

2012-06-13

..., Uranium Mill AGENCY: Nuclear Regulatory Commission. ACTION: Notice of Uranium milling alternative... amend their agreements to regulate uranium mill tailings (11e.(2) byproduct material). Six Agreement... transferring the Uravan uranium mill site to the U.S. Department of Energy. The NRC staff found no deficiencies...

Nonperturbative Results for Yang-Mills Theories

DEFF Research Database (Denmark)

Sannino, Francesco; Schechter, Joseph

2010-01-01

Some non perturbative aspects of the pure SU(3) Yang-Mills theory are investigated assuming a specific form of the beta function, based on a recent modification by Ryttov and Sannino of the known one for supersymmetric gauge theories. The characteristic feature is a pole at a particular value....... Assuming the usual QCD value one finds it to be 1.67 GeV, which is in surprisingly good agreement with a quenched lattice calculation. A similar calculation is made for the supersymmetric Yang-Mills theory where the corresponding beta function is considered to be exact....

Automation for pilger mills at NZFP

International Nuclear Information System (INIS)

Manoher; Ramesh, K.; Rout, J.K.

1997-01-01

Pilgering is the critical operation in production of zircaloy fuel tubes. The in-going tube is required for feeding in pilgering and the outgoing pilger tube length is measured and is cut into required lengths and transferred to storage tank before sending for degreasing. The paper deals with the automation of the above operation carried out on the pilger mills of New Zircaloy Fabrication Plant (NZFP). This has helped in improving the quality of the pilgered tubes and productivity of the mill besides eliminating manual handling and cutting operations

Swedish Pulp Mill Biorefineries. A vision of future possibilities

Energy Technology Data Exchange (ETDEWEB)

Berntsson, Thore (Chamers Univ. of Technology, Goeteborg (Sweden)); Axegaard, Peter; Backlund, Birgit; Samuelsson, Aasa; Berglin, Niklas; Lindgren, Karin (STFI-Packforsk, Stockholm (Sweden))

2008-07-01

Today, modern science could make it possible to develop techniques for refining almost the whole wood-matter, pulp mill side streams and bark compounds into platform chemicals, electricity, high quality fuels and structured feed-stock for chemicals and materials. The major challenge is to convert the state of basic scientific knowledge into industrial practise. Our definition of an integrated biorefinery is: 'Full utilization of the incoming biomass and other raw materials for simultaneous and economically optimized production of fibres, chemicals and energy'. Examples of products from a pulp mill biorefinery are: Chemicals and Materials (Phenols, adhesives, carbon fibres, activated carbon, binders, barriers, adhesives, antioxidants, surfactants, chelants, solvents, adhesives surfactants, descaling agents, specialty polymers, pharmaceuticals, nutraceuticals, cosmetics etc., Biofuels (pellets, lignin fuel, methanol, DME, ethanol etc), Electricity (BLGCC, condensing power etc.). The new or increased amounts of traditional products can be made from internal and/or external biomass. Three different levels can be identified: A high degree of energy saving in future mills, especially chemical pulp mills, will lead to large amounts of excess internal biomass which can be transferred to products mentioned above, Components in e.g. the black liquor, forest residues and bark can be upgraded to more valuable ones and the energy balance of the mill is kept through fuel import, wholly or partly depending on the level of mill energy efficiency. This imported fuel can be biomass or other types. External (imported) biomass (in some cases together with excess internal biomass) can be upgraded using synergy effects of docking this upgrading to a pulp mill. Electricity has been included as one of the possible biorefinery products. The electricity production in a mill can be increased in several ways which cannot be directly considered as biorefineries, e.g. recovery boiler

Industrial recovered-materials-utilization targets for the textile-mill-products industry

Energy Technology Data Exchange (ETDEWEB)

None

1979-01-01

The Congress, in the National Energy Conservation and Policy Act of 1978 (NECPA), directed the Department of Energy to establish materials recovery targets for the metals and metal products, paper and allied products, rubber, and textile-mill-products industries. The targets were developed to provide incentives for using energy-saving recorded materials and to provied a yardstick for measuring progress and improvement in this endeavor. The NECPA indicates that the targets should represent the maximum technically and economically feasible increase in the use of energy-saving recovered materials that each industry can achieve progressively by January 1, 1987. Materials affected by recovered-materials targets include and are limited to aluminum, copper, lead, zinc, iron, steel, paper and associated products, textile-mill, products, and rubber. Using information gathered from the textile-mill-products industry and from other textile-relaed sources, DOE has developed recovered materials targets for that industry. This report presents those targets and their basis and justification. Following an overview of the textile industry, the chapters are: Textile-Mill-Products Industry Operations; Economic Analysis of the Textile-Mill-Products Industry; Governmental and Regulatory Influence on the US Textile Industry; Current Mill Use of Recovered Materials in the Textile-Mill-Products Industry; Limitations on the Use of Recovered Materials in the US Textile-Mill-Products Industry; Materials-Recovery Targets; and Government and Industry Actions That Could Increase the Use of Recovered Materials.

Proposed ground water protection strategy for the Uranium Mill Tailings Site at Green River, Utah. Final report

International Nuclear Information System (INIS)

1994-11-01

This document presents the US DOE water resources protection strategy for the Green River, Utah mill tailings disposal site. The modifications in the original plan are based on new information, including ground water quality data collected after remedial action was completed, and on a revised assessment of disposal cell design features, surface conditions, and site hydrogeology. All aspects are discussed in this report

Aluminum-graphite composite produced by mechanical milling and hot extrusion

International Nuclear Information System (INIS)

Flores-Zamora, M.I.; Estrada-Guel, I.; Gonzalez-Hernandez, J.; Miki-Yoshida, M.; Martinez-Sanchez, R.

2007-01-01

Aluminum-graphite composites were produced by mechanical milling followed by hot extrusion. Graphite content was varied between 0 and 1 wt.%. Al-graphite mixtures were initially mixed in a shaker mill without ball, followed by mechanical milling in a High-energy simoloyer mill for 2 h under argon atmosphere. Milled powders were subsequently pressed at ∼950 MPa for 2 min, and next sintered under vacuum for 3 h at 823 K. Finally, sintered products were held for 0.5 h at 823 K and hot extruded using indirect extrusion. Tension and compression tests were carried out to determine the yield stress and maximum stress of the materials. We found that the mechanical resistance increased as the graphite content increased. Microstructural characterization was done by transmission electron microscopy. Al-O-C nanofibers and graphite nanoparticles were observed in extruded samples by transmission electron microscopy. These nanoparticles and nanofibers seemed to be responsible of the reinforcement phenomenon

Experimental Investigation on Ductile Mode Micro-Milling of ZrO2 Ceramics with Diamond-Coated End Mills

Directory of Open Access Journals (Sweden)

Rong Bian

2018-03-01

Full Text Available ZrO2 ceramics are currently used in a broad range of industrial applications. However, the machining of post-sintered ZrO2 ceramic is a difficult task, due to its high hardness and brittleness. In this study, micro-milling of ZrO2 with two kinds of diamond-coated end mills has been conducted on a Kern MMP 2522 micro-milling center (Kern Microtechnik GmbH, Eschenlohe, Germany. To achieve a ductile mode machining of ZrO2, the feed per tooth and depth of cut was set in the range of a few micrometers. Cutting force and machined surface roughness have been measured by a Kistler MiniDynamometer (Kistler Group, Winterthur, Switzerland and a Talysurf 120 L profilometer (Taylor Hobson Ltd., Leicester, UK, respectively. Machined surface topography and tool wear have been examined under SEM. Experiment results show that the material can be removed in ductile mode, and mirror quality surface with Ra low as 0.02 μm can be achieved. Curled and smooth chips have been collected and observed. The axial cutting force Fz is always bigger than Fx and Fy, and presents a rising trend with increasing of milling length. Tool wear includes delamination of diamond coating and wear of tungsten carbide substrate. Without the protection of diamond coating, the tungsten carbide substrate was worn out quickly, resulting a change of tool tip geometry.

A top-down assessment of energy, water and land use in uranium mining, milling, and refining

International Nuclear Information System (INIS)

Schneider, E.; Carlsen, B.; Tavrides, E.; Hoeven, C. van der; Phathanapirom, U.

2013-01-01

Land, water and energy use are key measures of the sustainability of uranium production into the future. As the most attractive, accessible deposits are mined out, future discoveries may prove to be significantly, perhaps unsustainably, more intensive consumers of environmental resources. A number of previous attempts have been made to provide empirical relationships connecting these environmental impact metrics to process variables such as stripping ratio and ore grade. These earlier attempts were often constrained by a lack of real world data and perform poorly when compared against data from modern operations. This paper conditions new empirical models of energy, water and land use in uranium mining, milling, and refining on contemporary data reported by operating mines. It shows that, at present, direct energy use from uranium production represents less than 1% of the electrical energy produced by the once-through fuel cycle. Projections of future energy intensity from uranium production are also possible by coupling the empirical models with estimates of uranium crustal abundance, characteristics of new discoveries, and demand. The projections show that even for the most pessimistic of scenarios considered, by 2100, the direct energy use from uranium production represents less than 3% of the electrical energy produced by the contemporary once-through fuel cycle. - Highlights: • We present environmental impacts of conventional uranium (U) mining and milling technologies. • Impacts include direct energy consumption, land use and water use. • Contemporary mine and mill data is used, updating published estimates that relied on 1970s-era data. • The direct energy used to mine and mill uranium is below 1% of the electrical energy ultimately produced by the uranium. • Even if U demand growth is strong, the direct energy return on investment of U mining and milling will remain well above 1

Effect of milling time on the structure, particle size, and morphology of montmorillonite

International Nuclear Information System (INIS)

Abareshi, M.

2017-01-01

In the current research, effect of milling on the structure, particle size and morphology of montmorillonite was investigated. For this purpose, the montmorillonite was analyzed by X-ray diffraction, Fourier transform infrared spectroscopy, and scanning electron microscopy. Then the montmorillonite was milled using high energy planetary ball mill at different milling times (1-60 hours). After that, the structure, particle size and morphology of all samples were investigated by XRD, FTIR, SEM, and transmission electron microscopy. Results showed that the ball milling causes the particle size reduction of clay and separation of the clay layers. Moreover, ball milling increases the overall structural disorder and transforms the crystalline structure into an amorphous phase. Also, the morphology of clay particle changes from layered to aggregates of almost rounded particles after 60 hours of milling.

Milling properties of low temperature sintered zirconia blocks for dental use

Energy Technology Data Exchange (ETDEWEB)

Lan, Ting-Hsun; Wang, Chau-Hsiang [Department of Prosthodontics, Kaohsiung Medical University Hospital, Kaohsiung 80756, Taiwan (China); School of Dentistry, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 80728, Taiwan (China); Chen, Ker-Kong [Department of Conservation, Kaohsiung Medical University Hospital, Kaohsiung 80756, Taiwan (China); School of Dentistry, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 80728, Taiwan (China); Wang, Moo-Chin, E-mail: mcwang@kmu.edu.tw [Department of Fragrance and Cosmetic Science, Kaohsiung Medical University, 100 Shih-Chuan 1st Road, Kaohsiung 80728, Taiwan (China); Department of Medical Research, Kaohsiung Medical University Hospital, Kaohsiung, 80756, Taiwan (China); Lee, Huey-Er, E-mail: huerle@kmu.edu.tw [Department of Prosthodontics, Kaohsiung Medical University Hospital, Kaohsiung 80756, Taiwan (China); School of Dentistry, College of Dental Medicine, Kaohsiung Medical University, Kaohsiung 80728, Taiwan (China)

2017-04-01

To investigate the milling properties of different yttria-tetragonal zirconia polycrystalline (Y-TZP) block materials by applying a dental computer numerical control (CNC) milling center. Low temperature sintering zirconia block denoted by KMUZ (experimental) with two commercial zirconia blocks for T block made in Taiwan and a G block made in Germany were compared for the milling properties. Seventy-two specimens were milled using the same CNC milling center, and properties were evaluated by measuring the weight loss (g), milling time (s), margin integrity (%) and broken diameter (μm). The crystalline phases contents were identified by X-ray diffraction and the microstructures of the sintering specimens were observed by scanning electron microscopy and transmission electron microscopy. The mean milling time of G and KMUZ were significantly shorter than T (P < 0.05). The KMUZ samples exhibited the least weight loss among the three kinds of blocks (P < 0.05). The percentages of marginal integrity after milling were high in G and KMUZ but low in T (P < 0.05). The mean broken diameters were from 90 μm to 120 μm. The phase transformation of t-ZrO{sub 2} (KMUZ: 7.4%, G: 5.9%, T: 3.2%) to m-ZrO{sub 2} when facing the milling pressure in ZrO{sub 2} blocks was observed by XRD. The result of TEM microstructure of KMUZ revealed that Y and Si were soluble in grain boundaries. The results show that the milling properties of KMUZ were better than one commercial T and near the G. The hindered grain growth, as a result of the Y{sup 3+} content in the grain boundaries, also plays a role in promoting the abnormal grain growth of 3Y-TZP. - Highlights: • The phase transformation of t-ZrO{sub 2} to m-ZrO{sub 2} affects the milling properties. • The phase content of t-ZrO2 was 100% when sintering at 1350 °C for 2 h. • The Y{sup 3+} content in the grain boundaries that hinders grain growth. • The Y{sup 3+} content in boundaries also promotes the abnormal grain growth of 3Y-TZP.

Alloying and microstructural changes in platinum–titanium milled and annealed powders

International Nuclear Information System (INIS)

Maweja, Kasonde; Phasha, M.J.; Yamabe-Mitarai, Y.

2012-01-01

Graphical abstract: (a) SE-SEM micrographs of PtTi martensite formed in powder milled for short time annealed at 1500 °C and quenched in helium gas flow (b) BSE-SEM of structure formed after slow cooling. Highlights: ► A disordered metastable FCC Pt(Ti) solid solution was formed after longer milling period. ► HCP Ti crystals were first deformed and then the atoms were dissolved in strained FCC Pt lattices. ► Longer milling time suppressed the occurrence of martensitic transformation after annealing. ► Martensite phase was formed in products that went through a short milling time then annealed and quenched. ► The width of the martensite features formed was smaller at higher cooling rates. - Abstract: Equiatomic platinum–titanium powder mixtures were processed by high energy ball milling under argon atmosphere and sintered under vacuum. Evolution of the crystal structures and microstructures of the products formed were investigated by XRD and SEM techniques, respectively. The HCP crystals of Ti were first deformed and then a disordered metastable FCC Pt(Ti) solid solution was formed during milling due to semi-coherency of FCC lattices. A nanostructured Pt(Ti) product was formed after long milling time, which contained 44–47 at.% Ti and 53–56 at.% Pt. An ordered PtTi intermetallic was formed by annealing the metastable Pt(Ti) at temperature above 1300 °C. The crystal structure and microstructure of the TiPt phase depended on the milling time, annealing temperature and the cooling rate. The B19 PtTi plate martensite was formed after annealing at 1500 °C and quenching at a cooling rate of 23 °C/min to 200 °C/min for short time milled products. The width of martensite features was smaller at high cooling rate. In PtTi products milled for longer time, no martensitic transformation was observed on cooling the annealed samples. Small amounts of Pt 5 Ti 3 were formed in the powders milled for 16 h or more, followed by annealing at 1500 °C and furnace

Load Handling and Repetitive Movements Are Associated with Chronic Low Back Pain among Jute Mill Workers in India

Directory of Open Access Journals (Sweden)

S. Goswami

2016-01-01

Full Text Available Introduction. WHO recognizes low back pain as one of the most important ergonomic stressors. Therefore, the present study was designed to find out the magnitude of the problem among jute mill workers in India and identify possible associations. Methodology. This cross-sectional workplace based study was conducted among eight (8 selected jute mills of India. Subjects with self-reported back pain for at least last 12 weeks were included and n=717 male jute mill workers actively engaged in work entered the study and completed all assessments. Results. Among all participants 55% (n=392 had current chronic low back pain. Age was an important association with subjects in the age group of 40–59 years more likely to have pain (p=0.02, OR 1.44. Regarding ergonomic risk factors lifting of load of more than 20 kg (p=0.04, OR 1.42 and repetitive movements of limbs (p=0.03, OR 0.67 were significant associations of chronic low back pain. Conclusion. This study identified a significant prevalence of current chronic low back pain among jute mill workers. Regarding ergonomic risk factors the present study has identified two significant associations: lifting of load above 20 kg and repetitive movements of limbs. Therefore, this study has identified need for workplace interventions in this occupational group employing approximately 3,50,000 workers in India.

Load Handling and Repetitive Movements Are Associated with Chronic Low Back Pain among Jute Mill Workers in India

Science.gov (United States)

Goswami, S.; Dasgupta, S.; Samanta, A.; Talukdar, G.; Chanda, A.; Ray Karmakar, P.; Bhattacharya, D.

2016-01-01

Introduction. WHO recognizes low back pain as one of the most important ergonomic stressors. Therefore, the present study was designed to find out the magnitude of the problem among jute mill workers in India and identify possible associations. Methodology. This cross-sectional workplace based study was conducted among eight (8) selected jute mills of India. Subjects with self-reported back pain for at least last 12 weeks were included and n = 717 male jute mill workers actively engaged in work entered the study and completed all assessments. Results. Among all participants 55% (n = 392) had current chronic low back pain. Age was an important association with subjects in the age group of 40–59 years more likely to have pain (p = 0.02, OR 1.44). Regarding ergonomic risk factors lifting of load of more than 20 kg (p = 0.04, OR 1.42) and repetitive movements of limbs (p = 0.03, OR 0.67) were significant associations of chronic low back pain. Conclusion. This study identified a significant prevalence of current chronic low back pain among jute mill workers. Regarding ergonomic risk factors the present study has identified two significant associations: lifting of load above 20 kg and repetitive movements of limbs. Therefore, this study has identified need for workplace interventions in this occupational group employing approximately 3,50,000 workers in India. PMID:27563463

CVD carbon powders modified by ball milling

Directory of Open Access Journals (Sweden)

Kazmierczak Tomasz

2015-09-01

Full Text Available Carbon powders produced using a plasma assisted chemical vapor deposition (CVD methods are an interesting subject of research. One of the most interesting methods of synthesizing these powders is using radio frequency plasma. This method, originally used in deposition of carbon films containing different sp2/sp3 ratios, also makes possible to produce carbon structures in the form of powder. Results of research related to the mechanical modification of these powders have been presented. The powders were modified using a planetary ball mill with varying parameters, such as milling speed, time, ball/powder mass ratio and additional liquids. Changes in morphology and particle sizes were measured using scanning electron microscopy and dynamic light scattering. Phase composition was analyzed using Raman spectroscopy. The influence of individual parameters on the modification outcome was estimated using statistical method. The research proved that the size of obtained powders is mostly influenced by the milling speed and the amount of balls. Powders tend to form conglomerates sized up to hundreds of micrometers. Additionally, it is possible to obtain nanopowders with the size around 100 nm. Furthermore, application of additional liquid, i.e. water in the process reduces the graphitization of the powder, which takes place during dry milling.

Bifurcation and stability analysis of a nonlinear milling process

Science.gov (United States)

Weremczuk, Andrzej; Rusinek, Rafal; Warminski, Jerzy

2018-01-01

Numerical investigations of milling operations dynamics are presented in this paper. A two degree of freedom nonlinear model is used to study workpiece-tool vibrations. The analyzed model takes into account both flexibility of the tool and the workpiece. The dynamics of the milling process is described by the discontinuous ordinary differential equation with time delay, which can cause process instability. First, stability lobes diagrams are created on the basis of the parameters determined in impact test of an end mill and workpiece. Next, the bifurcations diagrams are performed for different values of rotational speeds.

Environmental impact of uranium mining and milling in Australia

International Nuclear Information System (INIS)

Levins, D.M.

1980-01-01

Australia has almost twenty per cent of the Western World's low-cost uranium reserves, located mostly in the Alligator Rivers region of the Northern Territory. At present, only one uranium mill is operating in Australia, but a number of new mills are planned for the early 1980s. Details are given of Australian uranium mining and milling proposals and the measures taken to minimize their environmental impact. Major factors affecting environmental impact are discussed, including treatment of liquid wastes, water management, control of radon and other airborne releases, and disposal of tailings. (auth)

MILLING MECHANICS OF MATERIALS ROLLED IN THICK LAYER

Directory of Open Access Journals (Sweden)

E. B. Lojechnikov

2006-01-01

Full Text Available Powder rolling conditions are systematized with the purpose of their compacting and milling. The generalized  condition of solid and free-flowing bulk material deformation is proposed in the  paper. The analytical solution of a stressed state of powder being shaped mechanically that ensures milling of its particles has been obtained.

Rough Mill Improvement Guide for Managers and Supervisors

Science.gov (United States)

Philip H. Mitchell; Jan Wiedenbeck; Bobby Ammerman; Bobby Ammerman

2005-01-01

Wood products manufacturers require an efficient recovery of product from lumber to remain profitable. A company's ability to obtain the best yield in lumber cut-up operations (i.e., the rough mill) varies according to the raw material, product, processing equipment, processing environment, and knowledge and skill of the rough mill's employees. This book...

Recycling of mill scale in sintering process

Directory of Open Access Journals (Sweden)

El-Hussiny N.A.

2011-01-01

Full Text Available This investigation deals with the effect of replacing some amount of Baharia high barite iron ore concentrate by mill scale waste which was characterized by high iron oxide content on the parameters of the sintering process., and investigation the effect of different amount of coke breeze added on sintering process parameters when using 5% mill scale waste with 95% iron ore concentrate. The results of this work show that, replacement of iron ore concentrate with mill scale increases the amount of ready made sinter, sinter strength and productivity of the sinter machine and productivity at blast furnace yard. Also, the increase of coke breeze leads to an increase the ready made sinter and productivity of the sintering machine at blast furnace yard. The productivity of the sintering machine after 5% decreased slightly due to the decrease of vertical velocity.

Characterization of prealloyed copper powders treated in high energy ball mill

International Nuclear Information System (INIS)

Rajkovic, Viseslava; Bozic, Dusan; Jovanovic, Milan T.

2006-01-01

The inert gas atomised prealloyed copper powders containing 3.5 wt.% Al were milled up to 20 h in the planetary ball mill in order to oxidize aluminium in situ with oxygen from the air. In the next procedure compacts from milled powder were synthesized by hot-pressing in argon atmosphere. Compacts from as-received Cu-3.5 wt.% Al powder and electrolytic copper powder were also prepared under the same conditions. Microstructural and morphological changes of high energy milled powder as well as changes of thermal stability and electrical conductivity of compacts were studied as a function of milling time and high temperature exposure at 800 deg. C. Optical, scanning electron microscopy (SEM) and X-ray diffraction analysis were performed for microstructural characterization, whereas thermal stability and electrical conductivity were evaluated by microhardness measurements and conductometer Sigmatest, respectively. The prealloyed 5 h-milled and compacted powder showed a significant increase in microhardness reaching the value of 2600 MPa, about 4 times greater than that of compacts synthesized from as-received electrolytic copper powder (670 MPa). The electrical conductivity of compacts from 5 h-milled powder was 52% IACS. The results were discussed in terms of the effect of small grain size and finely distributed alumina dispersoids on hardening and thermal stability of compacts

Effect of milling on the magnetic properties of Al–Mn obtained by mechanical alloying

International Nuclear Information System (INIS)

Betancourt, Mirna; Silva, Pedro; Gonzalez, Gema

2012-01-01

Highlights: ► Al–42 at.% Mn transforms to α-Mn(Al) by mechanical milling after 5 h of milling. ► Transformation to nano β-Mn is reached after 50 h of milling with 6 nm grain size. ► Milling strongly affects magnetic behavior. - Abstract: Al–Mn powders were prepared to obtain the compound Mn 42 Al 58 by mechanical alloying. The powders were milled during different periods (1 h, 5 h, 11.5 h, 15 h, 20 h and 50 h) using a SPEX 8000 mixer mill in nitrogen atmosphere. The materials were characterized by X-ray diffraction (XRD) and magnetic properties at room temperature, using a vibrating sample magnetometer (VSM). XRD shows partial transformation to α-Mn after only 1 h of milling and a mixture of α-Mn and β-Mn after 11.5 h of milling and further milling resulted in transformation to β-Mn phase with a grain size of 6 nm after 50 h. The change in magnetic properties with milling time is quite dramatic, from a ferromagnetic behavior for α-Mn(Al) to paramagnetic after 11.5 h of milling and showing again ferromagnetic behavior, with a strong increase of magnetization values of 5.5 emu/g, after 50 h of milling with formation of β-Mn(Al).

Eden Mills Community Hall energy audit prepared for Eden Mills going carbon neutral

Energy Technology Data Exchange (ETDEWEB)

Lay, R.; Aussant, C. [Enermodal Engineering Ltd., Kitchener, ON (Canada)

2009-04-22

This paper described an energy audit conducted as part of the Eden Mills going carbon neutral project during the spring and summer of 2008. The audit included an inspection of the Eden Mills community hall with a special focus on the building's mechanical system and building envelope. A blower door test was performed to depressurize the building and to measure the airtightness of the building envelope. An energy simulation model was then used to estimate energy use according to the buildings functions and components. Recommendations included the addition of wall insulation, the replacement of some windows, and improved return air ducting and warm air distribution systems. Various new thermostat control systems were also recommended, as well as the use of wood pellets in one of the hall's 2 furnaces. 20 tabs., 28 figs.

33 CFR 117.213 - New Haven Harbor, Quinnipiac and Mill Rivers.

Science.gov (United States)

2010-07-01

... Mill Rivers. 117.213 Section 117.213 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF... Haven Harbor, Quinnipiac and Mill Rivers. The draws of the Tomlinson bridge, mile 0.0, the Ferry Street... bridge, mile 0.4 across Mill River, shall operate as follows: (a) The draws shall open on signal; except...

A study on rheological characteristics of roller milled fenugreek fractions.

Science.gov (United States)

Sakhare, Suresh D; Inamdar, Aashitosh A; Prabhasankar, P

2016-01-01

Fenugreek seeds were fractionated by roller milling to get various fractions. The roller milled fractions and whole fenugreek flour (WFF) were evaluated for the flow behavior and time-dependent flow properties using a rotational viscometer at the temperatures of 10-60 (0)C. The samples subjected to a programmed shear rate increase linearly from 0 to 300 s(-1) in 3 min and successive decrease linearly shear rate from 300 s(-1) to 0 in 3 min. The roller milled fractions and WFF paste exhibited non-Newtonian pseudoplastic behavior. Difference in hysteresis loop area was observed among the roller milled fractions and WFF, being more noticeable at lower temperatures. Power law and Casson models were used to predict flow properties of samples. The power law model described well the flow behavior of the roller milled fractions and WFF at temperatures tested. Except flour (FL) fraction, consistency coefficient, m, increased with the temperature both in the forward and backward measurements. The roller milled fractions and WFF exhibited rheopectic behavior that increased viscosity with increasing the shear speed and the temperature. For all the sample tested, initial shear stress increased with increase in shear rate and temperature.