WorldWideScience

Sample records for coaxial wire method

  1. Double-sided coaxial circuit QED with out-of-plane wiring

    Science.gov (United States)

    Rahamim, J.; Behrle, T.; Peterer, M. J.; Patterson, A.; Spring, P. A.; Tsunoda, T.; Manenti, R.; Tancredi, G.; Leek, P. J.

    2017-05-01

    Superconducting circuits are well established as a strong candidate platform for the development of quantum computing. In order to advance to a practically useful level, architectures are needed which combine arrays of many qubits with selective qubit control and readout, without compromising on coherence. Here, we present a coaxial circuit quantum electrodynamics architecture in which qubit and resonator are fabricated on opposing sides of a single chip, and control and readout wiring are provided by coaxial wiring running perpendicular to the chip plane. We present characterization measurements of a fabricated device in good agreement with simulated parameters and demonstrating energy relaxation and dephasing times of T1 = 4.1 μs and T2 = 5.7 μs, respectively. The architecture allows for scaling to large arrays of selectively controlled and measured qubits with the advantage of all wiring being out of the plane.

  2. Magnetic field effects on the electron Raman scattering in coaxial cylindrical quantum well wires

    Energy Technology Data Exchange (ETDEWEB)

    Rezaei, G., E-mail: grezaei2001@gmail.com [Department of Physics, College of Sciences, Yasouj University, Yasouj 75914-353 (Iran, Islamic Republic of); Karimi, M.J.; Pakarzadeh, H. [Department of Physics, College of Sciences, Shiraz University of Technology, Shiraz 71555-313 (Iran, Islamic Republic of)

    2013-11-15

    Based on the effective mass and parabolic one band approximations, the influence of an external magnetic field on the differential cross-section for the intersubband electron Raman scattering process in coaxial cylindrical quantum well wires is investigated. The dependence of differential cross-section on magnetic field strength and structural parameters of the coaxial cylindrical quantum well wire is studied. It is found that the magnetic field strength and the geometrical size of the system have a great influence on the position of the singularities in the emission spectra. Moreover, one can control the frequency shift in the Raman spectrum by varying the magnetic field strength and the size of the coaxial cylindrical quantum well wire. -- Highlights: • Magnetic field effects on ERS in CCQWWs are investigated. • Light polarization vectors and geometrical size effects on the ERS are also studied. • Number, position and magnitude of the peaks depend on the magnetic field strength. • The light polarization vectors have a great influence on the magnitude of the peaks. • An increase in the size leads to the considerable changes in the emission spectra.

  3. A Coaxial Guide Wire-Catheter Technique to Facilitate Right Adrenal Vein Sampling: Evaluation in 76 Patients.

    Science.gov (United States)

    Andrews, James C; Thompson, Scott M; Young, William F

    2015-12-01

    A technique to facilitate blood sampling from the right adrenal vein is described. Between May 2012 and February 2015, 148 adrenal vein sampling (AVS) procedures were attempted. In 72 procedures, a simple 5-F end-hole catheter was employed. In 76, a coaxial guide wire technique was used when blood could not be aspirated, whereby a 0.018-inch guide wire was passed through the catheter and into a branch of the right adrenal vein and the sample was drawn around the wire by using a side-arm adaptor. Successful sampling was achieved in 71 of the 72 catheter-only procedures (98.6%) and in 75 of the 76 coaxial wire-assisted procedures (98.7%). This simple technique may eliminate the need for multiple catheter exchanges during AVS. Copyright © 2015 SIR. Published by Elsevier Inc. All rights reserved.

  4. Method of manufacturing superconductor wire

    Science.gov (United States)

    Motowidlo, Leszek

    2014-09-16

    A method for forming Nb.sub.3Sn superconducting wire is provided. The method employs a powder-in-tube process using a high-tin intermetallic compound, such as MnSn.sub.2, for producing the Nb.sub.3Sn. The use of a high-tin intermetallic compound enables the process to perform hot extrusion without melting the high-tin intermetallic compound. Alternatively, the method may entail drawing the wire without hot extrusion.

  5. Dual wire welding torch and method

    Science.gov (United States)

    Diez, Fernando Martinez; Stump, Kevin S.; Ludewig, Howard W.; Kilty, Alan L.; Robinson, Matthew M.; Egland, Keith M.

    2009-04-28

    A welding torch includes a nozzle with a first welding wire guide configured to orient a first welding wire in a first welding wire orientation, and a second welding wire guide configured to orient a second welding wire in a second welding wire orientation that is non-coplanar and divergent with respect to the first welding wire orientation. A method of welding includes moving a welding torch with respect to a workpiece joint to be welded. During moving the welding torch, a first welding wire is fed through a first welding wire guide defining a first welding wire orientation and a second welding wire is fed through a second welding wire guide defining a second welding wire orientation that is divergent and non-coplanar with respect to the first welding wire orientation.

  6. Microminiature coaxial cable and methods of manufacture

    Science.gov (United States)

    Bongianni, W. L.

    1983-12-01

    A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 (MU)m thick and from 150 to 200 (MU)m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dielectric. Alternately the foam dielectric embodiment may have a continuous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microballoons to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion.

  7. Design method of coaxial reflex hollow beam generator

    Science.gov (United States)

    Wang, Jiake; Xu, Jia; Fu, Yuegang; He, Wenjun; Zhu, Qifan

    2016-10-01

    In view of the light energy loss in central obscuration of coaxial reflex optical system, the design method of a kind of hollow beam generator is introduced. First of all, according to the geometrical parameter and obscuration ratio of front-end coaxial reflex optical system, calculate the required physical dimension of hollow beam, and get the beam expanding rate of the hollow beam generator according to the parameters of the light source. Choose the better enlargement ratio of initial expanding system using the relational expression of beam expanding rate and beam expanding rate of initial system; the traditional design method of the reflex optical system is used to design the initial optical system, and then the position of rotation axis of the hollow beam generator can be obtained through the rotation axis translation formula. Intercept the initial system bus bar using the rotation axis after the translation, and rotate the bus bar around the rotation axis for 360°, so that two working faces of the hollow beam generator can be got. The hollow beam generator designed by this method can get the hollow beam that matches the front-end coaxial reflex optical system, improving the energy utilization ratio of beam and effectively reducing the back scattering of transmission system.

  8. WO3 nanotubes prepared by a coaxial electrospinning method.

    Science.gov (United States)

    Cao, Xingxing; Zhang, Xuebin; Hu, Jixiang; Wang, Yang; Liu, Jia; Wu, Haijun; Feng, Yi

    2014-08-01

    In this paper, WO3 nanotubes were prepared by a coaxial electrospinning method. Firstly, core-shell structured composite fibers were fabricated via coaxial electrospinning under the optimal electro-spinning parameters to get the best composite fibers with uniform diameters and smooth surface, which pure PVA being the core solution and PVA/AMT/alcohol being the shell one, respectively. Secondly, the composite fibers were calcined in air at 600 °C for 4 h to wipe out the pure PVA, leading to the formation of nanotubes. After sintering, the obtained WO3 nanotubes were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HRTEM). The XRD show that the resultant materials consist of pure tungsten trioxide (WO3) with good crystallinity, while FESEM and HRTEM images indicate that the materials are nanotubes with rough surface and consist of nanoparticles. The inner diameter and the wall thickness of nanotubes were calculated to be around 100 and 50 nm, respectively.

  9. Wire-shaped ultraviolet photodetectors based on a nanostructured NiO/ZnO coaxial p-n heterojunction via thermal oxidation and hydrothermal growth processes

    Science.gov (United States)

    Ko, Yeong Hwan; Nagaraju, Goli; Yu, Jae Su

    2015-01-01

    We report the facile fabrication of wire-shaped ultraviolet photodetectors (WUPDs) by employing a nanostructured zinc oxide (ZnO)/nickel oxide (NiO) coaxial p-n heterojunction. The WUPD consists of a ZnO/NiO coaxial Ni wire and a twisted gold (Au) wire where the Ni and Au are used as the anode and cathode, respectively. For the coaxial p-n heterojunction, the NiO nanostructures (NSs) and the ZnO nanorods (NRs) are subsequently formed on the surface of Ni wire via thermal oxidation and hydrothermal growth processes. With an applied bias of -3.5 V, the WUPD exhibits good photoresponsivity of 7.37 A W-1 and an external quantum efficiency of 28.1% at an incident light wavelength of 325 nm. Under the UV illumination at a wavelength of 365 nm, the dark current and photocurrent are -3.97 × 10-7 and -8.47 × 10-6 A, respectively. For enhancing the photocurrent, the WUPD is threaded through a silver (Ag) coated glass tube which acts as a waveguide to concentrate the UV light of 365 nm on the WUPD. As a result, the photocurrent is significantly improved up to -1.56 × 10-5 A (i.e., 1.84 times) at the reverse bias of -3.5 V.We report the facile fabrication of wire-shaped ultraviolet photodetectors (WUPDs) by employing a nanostructured zinc oxide (ZnO)/nickel oxide (NiO) coaxial p-n heterojunction. The WUPD consists of a ZnO/NiO coaxial Ni wire and a twisted gold (Au) wire where the Ni and Au are used as the anode and cathode, respectively. For the coaxial p-n heterojunction, the NiO nanostructures (NSs) and the ZnO nanorods (NRs) are subsequently formed on the surface of Ni wire via thermal oxidation and hydrothermal growth processes. With an applied bias of -3.5 V, the WUPD exhibits good photoresponsivity of 7.37 A W-1 and an external quantum efficiency of 28.1% at an incident light wavelength of 325 nm. Under the UV illumination at a wavelength of 365 nm, the dark current and photocurrent are -3.97 × 10-7 and -8.47 × 10-6 A, respectively. For enhancing the photocurrent

  10. Coaxial lithography.

    Science.gov (United States)

    Ozel, Tuncay; Bourret, Gilles R; Mirkin, Chad A

    2015-04-01

    The optical and electrical properties of heterogeneous nanowires are profoundly related to their composition and nanoscale architecture. However, the intrinsic constraints of conventional synthetic and lithographic techniques have limited the types of multi-compositional nanowire that can be created and studied in the laboratory. Here, we report a high-throughput technique that can be used to prepare coaxial nanowires with sub-10 nm control over the architectural parameters in both axial and radial dimensions. The method, termed coaxial lithography (COAL), relies on templated electrochemical synthesis and can create coaxial nanowires composed of combinations of metals, metal oxides, metal chalcogenides and conjugated polymers. To illustrate the possibilities of the technique, a core/shell semiconductor nanowire with an embedded plasmonic nanoring was synthesized--a structure that cannot be prepared by any previously known method--and its plasmon-excitation-dependent optoelectronic properties were characterized.

  11. Coaxial Lithography

    Science.gov (United States)

    Ozel, Tuncay

    The optical and electrical properties of heterogeneous nanowires are profoundly related to their composition and nanoscale architecture. However, the intrinsic constraints of conventional synthetic and lithographic techniques have limited the types of multi-compositional nanowires that can be realized and studied in the laboratory. This thesis focuses on bridging templated electrochemical synthesis and lithography for expanding current synthetic capabilities with respect to materials generality and the ability to tailor two-dimensional growth in the formation of core-shell structures for the rational design and preparation of nanowires with very complex architectures that cannot be made by any other techniques. Chapter 1 introduces plasmonics, templated electrochemical synthesis, and on-wire lithography concepts and their significances within chemistry and materials science. Chapter 2 details a powerful technique for the deposition of metals and semiconductors with nanometer resolution in segment and gap lengths using on-wire lithography, which serves as a new platform to explore plasmon-exciton interactions in the form of long-range optical nanoscale rulers. Chapter 3 highlights an approach for the electrochemical synthesis of solution dispersible core-shell polymeric and inorganic semiconductor nanowires with metallic leads. A photodetector based on a single core-shell semiconductor nanowire is presented to demonstrate the functionality of the nanowires produced using this approach. Chapter 4 describes a new materials general technique, termed coaxial lithography (COAL), bridging templated electrochemical synthesis and lithography for generating coaxial nanowires in a parallel fashion with sub-10 nanometer resolution in both axial and radial dimensions. Combinations of coaxial nanowires composed of metals, metal oxides, metal chalcogenides, conjugated polymers, and a core/shell semiconductor nanowire with an embedded plasmonic nanoring are presented to

  12. System and method for evaluating a wire conductor

    Science.gov (United States)

    Panozzo, Edward; Parish, Harold

    2013-10-22

    A method of evaluating an electrically conductive wire segment having an insulated intermediate portion and non-insulated ends includes passing the insulated portion of the wire segment through an electrically conductive brush. According to the method, an electrical potential is established on the brush by a power source. The method also includes determining a value of electrical current that is conducted through the wire segment by the brush when the potential is established on the brush. The method additionally includes comparing the value of electrical current conducted through the wire segment with a predetermined current value to thereby evaluate the wire segment. A system for evaluating an electrically conductive wire segment is also disclosed.

  13. A Fast Measuring Method for the Inner Diameter of Coaxial Holes

    Science.gov (United States)

    Wang, Lei; Yang, Fangyun; Fu, Luhua; Wang, Zhong; Yang, Tongyu; Liu, Changjie

    2017-01-01

    A new method for fast diameter measurement of coaxial holes is studied. The paper describes a multi-layer measuring rod that installs a single laser displacement sensor (LDS) on each layer. This method is easy to implement by rotating the measuring rod, and immune from detecting the measuring rod’s rotation angles, so all diameters of coaxial holes can be calculated by sensors’ values. While revolving, the changing angles of each sensor’s laser beams are approximately equal in the rod’s radial direction so that the over-determined nonlinear equations of multi-layer holes for fitting circles can be established. The mathematical model of the measuring rod is established, all parameters that affect the accuracy of measurement are analyzed and simulated. In the experiment, the validity of the method is verified, the inner diameter measuring precision of 28 μm is achieved by 20 μm linearity LDS. The measuring rod has advantages of convenient operation and easy manufacture, according to the actual diameters of coaxial holes, and also the varying number of holes, LDS’s mounting location can be adjusted for different parts. It is convenient for rapid diameter measurement in industrial use. PMID:28327499

  14. Synthesis method for ultrananocrystalline diamond in powder employing a coaxial arc plasma gun

    Science.gov (United States)

    Naragino, Hiroshi; Tominaga, Aki; Hanada, Kenji; Yoshitake, Tsuyoshi

    2015-07-01

    A new method that enables us to synthesize ultrananocrystalline diamond (UNCD) in powder is proposed. Highly energetic carbon species ejected from a graphite cathode of a coaxial arc plasma gun were provided on a quartz plate at a high density by repeated arc discharge in a compact vacuum chamber, and resultant films automatically peeled from the plate were aggregated and powdered. The grain size was easily controlled from 2.4 to 15.0 nm by changing the arc discharge energy. It was experimentally demonstrated that the proposed method is a new and promising method that enables us to synthesize UNCD in powder easily and controllably.

  15. An interconnecting bus power optimization method combining interconnect wire spacing with wire ordering

    Institute of Scientific and Technical Information of China (English)

    Zhu Zhang-Ming; Hao Bao-Tian; En Yun-Fei; Yang Yin-Tang; Li Yue-Jin

    2011-01-01

    On-chip interconnect buses consume tens of percents of dynamic power in a nanometer scale integrated circuit and they will consume more power with the rapid scaling down of technology size and continuously rising clock frequency,therefore it is meaningful to lower the interconnecting bus power in design. In this paper, a simple yet accurate interconnect parasitic capacitance model is presented first and then, based on this model, a novel interconnecting bus optimization method is proposed. Wire spacing is a process for spacing wires for minimum dynamic power, while wire ordering is a process that searches for wire orders that maximally enhance it. The method, i.e., combining wire spacing with wire ordering, focuses on bus dynamic power optimization with a consideration of bus performance requirements.The optimization method is verified based on various nanometer technology parameters, showing that with 50% slack of routing space, 25.71% and 32.65% of power can be saved on average by the proposed optimization method for a globalbus and an intermediate bus, respectively, under a 65-nm technology node, compared with 21.78% and 27.68% of power saved on average by uniform spacing technology. The proposed method is especially suitable for computer-aided designof nanometer scale on-chip buses.

  16. Coaxial Electric Heaters

    Science.gov (United States)

    Strekalov, Dmitry; Matsko, Andrey; Savchenkov, Anatoliy; Maleki, Lute

    2008-01-01

    Coaxial electric heaters have been conceived for use in highly sensitive instruments in which there are requirements for compact heaters but stray magnetic fields associated with heater electric currents would adversely affect operation. Such instruments include atomic clocks and magnetometers that utilize heated atomic-sample cells, wherein stray magnetic fields at picotesla levels could introduce systematic errors into instrument readings. A coaxial electric heater is essentially an axisymmetric coaxial cable, the outer conductor of which is deliberately made highly electrically resistive so that it can serve as a heating element. As in the cases of other axisymmetric coaxial cables, the equal magnitude electric currents flowing in opposite directions along the inner and outer conductors give rise to zero net magnetic field outside the outer conductor. Hence, a coaxial electric heater can be placed near an atomic-sample cell or other sensitive device. A coaxial electric heater can be fabricated from an insulated copper wire, the copper core of which serves as the inner conductor. For example, in one approach, the insulated wire is dipped in a colloidal graphite emulsion, then the emulsion-coated wire is dried to form a thin, uniform, highly electrically resistive film that serves as the outer conductor. Then the film is coated with a protective layer of high-temperature epoxy except at the end to be electrically connected to the power supply. Next, the insulation is stripped from the wire at that end. Finally, electrical leads from the heater power supply are attached to the exposed portions of the wire and the resistive film. The resistance of the graphite film can be tailored via its thickness. Alternatively, the film can be made from an electrically conductive paint, other than a colloidal graphite emulsion, chosen to impart the desired resistance. Yet another alternative is to tailor the resistance of a graphite film by exploiting the fact that its resistance

  17. Recent Applications of Coaxial and Emulsion Electrospinning Methods in the Field of Tissue Engineering.

    Science.gov (United States)

    McClellan, Phillip; Landis, William J

    2016-01-01

    Electrospinning has emerged as an effective method of producing nanoscale fibers for use in multiple fields of study. One area of significant interest is nanofiber utilization for tissue engineering because the nanofibrous mats can mimic the native extracellular matrix of biological tissues. A logical next step is the inclusion of certain molecules and compounds to accelerate or increase the efficacy of tissue regeneration. Two methods are under scrutiny for their capability to encapsulate therapeutic compounds within electrospun nanofibers: emulsion and coaxial electrospinning. Both have advantages and disadvantages, which need to be taken into careful consideration when deciding to use them in a specific application. Several examples are provided here to highlight the vast potential of multilayered nanofibers as well as the emergence of new techniques to produce three-dimensional scaffolds of nanofibers for use in the field of tissue engineering.

  18. Recent Applications of Coaxial and Emulsion Electrospinning Methods in the Field of Tissue Engineering

    Directory of Open Access Journals (Sweden)

    Phillip McClellan

    2016-08-01

    Full Text Available Electrospinning has emerged as an effective method of producing nanoscale fibers for use in multiple fields of study. One area of significant interest is nanofiber utilization for tissue engineering because the nanofibrous mats can mimic the native extracellular matrix of biological tissues. A logical next step is the inclusion of certain molecules and compounds to accelerate or increase the efficacy of tissue regeneration. Two methods are under scrutiny for their capability to encapsulate therapeutic compounds within electrospun nanofibers: emulsion and coaxial electrospinning. Both have advantages and disadvantages, which need to be taken into careful consideration when deciding to use them in a specific application. Several examples are provided here to highlight the vast potential of multilayered nanofibers as well as the emergence of new techniques to produce three-dimensional scaffolds of nanofibers for use in the field of tissue engineering.

  19. Coaxial electrospun fibers: applications in drug delivery and tissue engineering.

    Science.gov (United States)

    Lu, Yang; Huang, Jiangnan; Yu, Guoqiang; Cardenas, Romel; Wei, Suying; Wujcik, Evan K; Guo, Zhanhu

    2016-09-01

    Coelectrospinning and emulsion electrospinning are two main methods for preparing core-sheath electrospun nanofibers in a cost-effective and efficient manner. Here, physical phenomena and the effects of solution and processing parameters on the coaxial fibers are introduced. Coaxial fibers with specific drugs encapsulated in the core can exhibit a sustained and controlled release. Their exhibited high surface area and three-dimensional nanofibrous network allows the electrospun fibers to resemble native extracellular matrices. These features of the nanofibers show that they have great potential in drug delivery and tissue engineering applications. Proteins, growth factors, antibiotics, and many other agents have been successfully encapsulated into coaxial fibers for drug delivery. A main advantage of the core-sheath design is that after the process of electrospinning and release, these drugs remain bioactive due to the protection of the sheath. Applications of coaxial fibers as scaffolds for tissue engineering include bone, cartilage, cardiac tissue, skin, blood vessels and nervous tissue, among others. A synopsis of novel coaxial electrospun fibers, discussing their applications in drug delivery and tissue engineering, is covered pertaining to proteins, growth factors, antibiotics, and other drugs and applications in the fields of bone, cartilage, cardiac, skin, blood vessel, and nervous tissue engineering, respectively. WIREs Nanomed Nanobiotechnol 2016, 8:654-677. doi: 10.1002/wnan.1391 For further resources related to this article, please visit the WIREs website.

  20. Coaxial printing method for directly writing stretchable cable as strain sensor

    Science.gov (United States)

    Yan, Hai-liang; Chen, Yan-qiu; Deng, Yong-qiang; Zhang, Li-long; Hong, Xiao; Lau, Woon-ming; Mei, Jun; Hui, David; Yan, Hui; Liu, Yu

    2016-08-01

    Through applying the liquid metal and elastomer as the core and shell materials, respectively, a coaxial printing method is being developed in this work for preparing a stretchable and conductive cable. When liquid metal alloy eutectic Gallium-Indium is embedded into the elastomer matrix under optimized control, the cable demonstrates well-posed extreme mechanic performance, under stretching for more than 350%. Under developed compression test, the fabricated cable also demonstrates the ability for recovering original properties due to the high flowability of the liquid metal and super elasticity of the elastomeric shell. The written cable presents high cycling reliability regarding its stretchability and conductivity, two properties which can be clearly predicted in theoretical calculation. This work can be further investigated as a strain sensor for monitoring motion status including frequency and amplitude of a curved object, with extensive applications in wearable devices, soft robots, electronic skins, and wireless communication.

  1. Coaxial printing method for directly writing stretchable cable as strain sensor

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Hai-liang [College of Material Science and Engineering, Beijing University of Technology, 100124 Beijing (China); Chengdu Green Energy and Green Manufacturing Technology R& D Center, 610299 Chengdu (China); Chen, Yan-qiu, E-mail: yu.liu@vip.163.com, E-mail: cyqleaf@qq.com, E-mail: hyan@but.ac.cn; Deng, Yong-qiang; Zhang, Li-long; Lau, Woon-ming; Mei, Jun; Liu, Yu, E-mail: yu.liu@vip.163.com, E-mail: cyqleaf@qq.com, E-mail: hyan@but.ac.cn [Chengdu Green Energy and Green Manufacturing Technology R& D Center, 610299 Chengdu (China); Hong, Xiao [Chengdu Green Energy and Green Manufacturing Technology R& D Center, 610299 Chengdu (China); College of Computer Science, Sichuan University, Chengdu 610207 (China); Hui, David [Department of Mechanical Engineering, University of New Orleans, New Orleans, Louisiana 70148 (United States); Yan, Hui, E-mail: yu.liu@vip.163.com, E-mail: cyqleaf@qq.com, E-mail: hyan@but.ac.cn [College of Material Science and Engineering, Beijing University of Technology, 100124 Beijing (China)

    2016-08-22

    Through applying the liquid metal and elastomer as the core and shell materials, respectively, a coaxial printing method is being developed in this work for preparing a stretchable and conductive cable. When liquid metal alloy eutectic Gallium-Indium is embedded into the elastomer matrix under optimized control, the cable demonstrates well–posed extreme mechanic performance, under stretching for more than 350%. Under developed compression test, the fabricated cable also demonstrates the ability for recovering original properties due to the high flowability of the liquid metal and super elasticity of the elastomeric shell. The written cable presents high cycling reliability regarding its stretchability and conductivity, two properties which can be clearly predicted in theoretical calculation. This work can be further investigated as a strain sensor for monitoring motion status including frequency and amplitude of a curved object, with extensive applications in wearable devices, soft robots, electronic skins, and wireless communication.

  2. Model for predicting thermal conductivity using transient hot wire method

    Science.gov (United States)

    Kumar, Sublania Harish; Singh K., J.; Somani A., K.

    2016-05-01

    The use of the hot wire method for estimating the thermal conductivity measurement has recently known a significant increase. However, this method is theoretically not applicable to materials. Thermal conductivity values are necessary whenever a heat transfer problem is to be evaluated.

  3. Extraction of lanthanides by polysulfone microcapsules containing EHPNA. II. Coaxial microfluidic method

    Institute of Scientific and Technical Information of China (English)

    王月; 靖宇; 侯海龙; 徐建鸿; 王运东

    2015-01-01

    Controllable preparation of small-size polysulfone microcapsules (MC) containing 2-ethylhexylphosphonic acid mono-2- ethylhexyl ester (EHPNA) by coaxial microfluidic method was focused on. N2 gas was used as continuous phase to disperse the polymer solution. The influence of polysulfone (PSF) content in the polymer solution and N2 gas flow rate on the structural properties and loading ratio of microcapsules was investigated. The mean diameter of prepared microcapsules was between 0.90 and 1.60 mm. Ultrasound method was adopted to import EHPNA into microcapsules. A very high extractant loading ratio of 6.21 g-EHPNA/g-PSF was achieved when the pore volume was 6.89 mL/g. The extraction performance was determined with lanthanides as the recovered components and with the prepared microcapsules as the separation agent. Close-packed microcapsules enjoyed a fast extraction ki-netics. The maximum uptakes of La3+, Sm3+ and Er3+ were 3.02×10–4 mol/g, 8.05×10–4 mol/g and 5.58×10–4 mol/g, respectively. Microcapsules were reused seven times and showed very good stability. It is promising to apply the microcapsules into the extraction column and realize continuous operation.

  4. Coaxial Switch

    Science.gov (United States)

    2014-04-23

    movement of the shaft 120 is towards the first end 106 of the housing 102 and the conductor members 142 and 144 are aligned with the desired coaxial...the user then rotates the shaft 120 so that the conductor members 142 and 144 on the support plate 140 are aligned with the appropriate pair of...then rotates the shaft 120 so that the conductor members 142 and 144 are aligned with a different combination of coaxial connector body members

  5. New method for lightning location using optical ground wire

    Institute of Scientific and Technical Information of China (English)

    Zhaoyu Qin; Zhaogu Cheng; Zhiping Zhang; Jianqiang Zhu; Feng Li

    2006-01-01

    A new technology of lightning location is described, which is based on detecting the state of polarization(SOP) fluctuation of the laser light in the optic ground wire (OPGW). Compared with the conventional lightning location method, the new method is more accurate, more stable, and cheaper. Theories of Stokes generated by lightning strike can still be accurately identified by detecting the velocity of polarization motion. A new algorithm to quantify the velocity is also introduced.

  6. A method for predicting static-to-flight effects on coaxial jet noise

    Science.gov (United States)

    Bryce, William D.; Chinoy, Cyrus B.

    2016-08-01

    Previously-published work has provided a theoretical modelling of the jet noise from coaxial nozzle configurations in the form of component sources which can each be quantified in terms of modified single-stream jets. This modelling has been refined and extended to cover a wide range of the operating conditions of aircraft turbofan engines with separate exhaust flows, encompassing area ratios from 0.8 to 4. The objective has been to establish a basis for predicting the static-to-flight changes in the coaxial jet noise by applying single-stream flight effects to each of the sources comprising the modelling of the coaxial jet noise under static conditions. Relatively few experimental test points are available for validation although these do cover the full extent of the jet conditions and area ratios considered. The experimental results are limited in their frequency range by practical considerations but the static-to-flight changes in the third-octave SPLs are predicted to within a standard deviation of 0.4 dB although the complex effects of jet refraction and convection cause the errors to increase at low flight emission angles to the jet axis. The modelling also provides useful insights into the mechanisms involved in the generation of coaxial jet noise and has facilitated the identification of inadequacies in the experimental simulation of flight effects.

  7. Development of (1 0 0) crystallographic texture in magnetostrictive Fe-Ga wires using a modified Taylor wire method

    Energy Technology Data Exchange (ETDEWEB)

    Farrell, S P; Quigley, P E; Avery, K J [Defence R and D Canada-Atlantic, 9 Grove Street, Dartmouth, NS, B2Y 3Z7 (Canada); Hatchard, T D; Flynn, S E; Dunlap, R A, E-mail: shannonfarrell@drdc-rddc.gc.c [Department of Physics and Atmospheric Science, Dalhousie University, Halifax, NS, B3H 3J5 (Canada)

    2009-07-07

    Magnetostrictive Fe-Ga wires 1-3 mm in diameter have been prepared using an innovative cost-effective approach-based on the Taylor wire method-that couples the advantages of high-temperature directional solidification and selective grain growth. Strict control of drawing processes has been shown to enable the introduction of desirable texture that is critical for achieving large magnetostriction in these polycrystalline Fe-Ga alloys. The procedure for fabricating highly textured (1 0 0) magnetostrictive wires is discussed and the wires are evaluated in terms of microstructure and crystallographic texture. Magnetostriction measurements, in the absence of pre-stress and stress-annealing treatments, indicated a maximum magnetostriction of approx170 ppm in a saturation field less than 60 mT. A mechanism for texture evolution is proposed. It is speculated that the resultant (1 0 0) texture of the Fe-Ga wires is due to directional solidification and abnormal grain growth resulting from surface effects. The unique properties of wires made with the Taylor-based approach coupled with the low fabrication cost make this an attractive approach for the production of Fe-Ga wire with a specific crystallographic texture.

  8. New method for lightning location using optical ground wire

    Science.gov (United States)

    Qin, Zhaoyu; Cheng, Zhaogu; Zhang, Zhiping; Zhu, Jianqiang; Li, Feng

    2006-12-01

    A new technology of lightning location is described, which is based on detecting the state of polarization (SOP) fluctuation of the laser light in the optic ground wire (OPGW). Compared with the conventional lightning location method, the new method is more accurate, more stable, and cheaper. Theories of Stokes parameters and Poincare sphere are introduced to analyze the SOP at the lightning strike point. It can be concluded that although the initial points of SOP on the Poincare sphere are random, the SOP fluctuation generated by lightning strike can still be accurately identified by detecting the velocity of polarization motion. A new algorithm to quantify the velocity is also introduced.

  9. Standard Test Method for Sag of Tungsten Wire

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2014-01-01

    1.1 This test method covers a determination of the sag properties of tungsten wire 0.030 in. (0.76 mm) and over in diameter. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  10. Magnetic Alignment of Pulsed Solenoids Using the Pulsed Wire Method

    Energy Technology Data Exchange (ETDEWEB)

    Arbelaez, D.; Madur, A.; Lipton, T.M.; Waldron, W.L.; Kwan, J.W.

    2011-04-01

    A unique application of the pulsed-wire measurement method has been implemented for alignment of 2.5 T pulsed solenoid magnets. The magnetic axis measurement has been shown to have a resolution of better than 25 {micro}m. The accuracy of the technique allows for the identification of inherent field errors due to, for example, the winding layer transitions and the current leads. The alignment system is developed for the induction accelerator NDCX-II under construction at LBNL, an upgraded Neutralized Drift Compression experiment for research on warm dense matter and heavy ion fusion. Precise alignment is essential for NDCX-II, since the ion beam has a large energy spread associated with the rapid pulse compression such that misalignments lead to corkscrew deformation of the beam and reduced intensity at focus. The ability to align the magnetic axis of the pulsed solenoids to within 100 pm of the induction cell axis has been demonstrated.

  11. Bubble reconstruction method for wire-mesh sensors measurements

    Science.gov (United States)

    Mukin, Roman V.

    2016-08-01

    A new algorithm is presented for post-processing of void fraction measurements with wire-mesh sensors, particularly for identifying and reconstructing bubble surfaces in a two-phase flow. This method is a combination of the bubble recognition algorithm presented in Prasser (Nuclear Eng Des 237(15):1608, 2007) and Poisson surface reconstruction algorithm developed in Kazhdan et al. (Poisson surface reconstruction. In: Proceedings of the fourth eurographics symposium on geometry processing 7, 2006). To verify the proposed technique, a comparison was done of the reconstructed individual bubble shapes with those obtained numerically in Sato and Ničeno (Int J Numer Methods Fluids 70(4):441, 2012). Using the difference between reconstructed and referenced bubble shapes, the accuracy of the proposed algorithm was estimated. At the next step, the algorithm was applied to void fraction measurements performed in Ylönen (High-resolution flow structure measurements in a rod bundle (Diss., Eidgenössische Technische Hochschule ETH Zürich, Nr. 20961, 2013) by means of wire-mesh sensors in a rod bundle geometry. The reconstructed bubble shape yields bubble surface area and volume, hence its Sauter diameter d_{32} as well. Sauter diameter is proved to be more suitable for bubbles size characterization compared to volumetric diameter d_{30}, proved capable to capture the bi-disperse bubble size distribution in the flow. The effect of a spacer grid was studied as well: For the given spacer grid and considered flow rates, bubble size frequency distribution is obtained almost at the same position for all cases, approximately at d_{32} = 3.5 mm. This finding can be related to the specific geometry of the spacer grid or the air injection device applied in the experiments, or even to more fundamental properties of the bubble breakup and coagulation processes. In addition, an application of the new algorithm for reconstruction of a large air-water interface in a tube bundle is

  12. Cooling method prolongs life of hot-wire transducer

    Science.gov (United States)

    Baldwin, L. V.; Sandborn, V. A.

    1964-01-01

    To cool a hot-wire transducer, the two ends of the wire are supported on thermally and electrically conductive rods, surrounded by a fluid cooling medium. By keeping the supporting rods at a substantially constant temperature, the probe is prevented from overheating.

  13. Intermetallic alloy welding wires and method for fabricating the same

    Science.gov (United States)

    Santella, M.L.; Sikka, V.K.

    1996-06-11

    Welding wires for welding together intermetallic alloys of nickel aluminides, nickel-iron aluminides, iron aluminides, or titanium aluminides, and preferably including additional alloying constituents are fabricated as two-component, clad structures in which one component contains the primary alloying constituent(s) except for aluminum and the other component contains the aluminum constituent. This two-component approach for fabricating the welding wire overcomes the difficulties associated with mechanically forming welding wires from intermetallic alloys which possess high strength and limited ductilities at elevated temperatures normally employed in conventional metal working processes. The composition of the clad welding wires is readily tailored so that the welding wire composition when melted will form an alloy defined by the weld deposit which substantially corresponds to the composition of the intermetallic alloy being joined. 4 figs.

  14. Parallel-wire grid assembly with method and apparatus for construction thereof

    Energy Technology Data Exchange (ETDEWEB)

    Lewandowski, Edward F. (Westmont, IL); Vrabec, John (South Holland, IL)

    1984-01-01

    Disclosed is a parallel wire grid and an apparatus and method for making the same. The grid consists of a generally coplanar array of parallel spaced-apart wires secured between metallic frame members by an electrically conductive epoxy. The method consists of continuously winding a wire about a novel winding apparatus comprising a plurality of spaced-apart generally parallel spindles. Each spindle is threaded with a number of predeterminedly spaced-apart grooves which receive and accurately position the wire at predetermined positions along the spindle. Overlying frame members coated with electrically conductive epoxy are then placed on either side of the wire array and are drawn together. After the epoxy hardens, portions of the wire array lying outside the frame members are trimmed away.

  15. An Interactive Method Based on the Live Wire for Segmentation of the Breast in Mammography Images

    OpenAIRE

    Zhang Zewei; Wang Tianyue; Guo Li; Wang Tingting; Xu Lu

    2014-01-01

    In order to improve accuracy of computer-aided diagnosis of breast lumps, the authors introduce an improved interactive segmentation method based on Live Wire. This paper presents the Gabor filters and FCM clustering algorithm is introduced to the Live Wire cost function definition. According to the image FCM analysis for image edge enhancement, we eliminate the interference of weak edge and access external features clear segmentation results of breast lumps through improving Live Wire on two...

  16. CO-AXIAL DISCHARGES

    Science.gov (United States)

    Luce, J.S.; Smith, L.P.

    1960-11-22

    A method and apparatus are given for producing coaxial arc discharges in an evacuated enclosure and within a strong, confining magnetic field. The arcs are maintained at a high potential difference. Electrons will diffuse to the more positive arc from the negative arc, and positive ions will diffuse from the more positive arc to the negative arc. Coaxial arc discharges have the advantage that ions which return to strike the positive arc discharge will lose no energy since they do not strike a solid wall or electrode. Those discharges are useful in confining an ionized plasma between the discharges, and have the advantage of preventing impurities from the walls of the enclosure from entering ihe plasma area because of the arc barrier set up bv the cylindrical outer arc.

  17. Hot-Wire Method for Kinematic Viscosity Estimation

    Science.gov (United States)

    Giaretto, Valter

    2010-03-01

    This paper explores the characterization of thermal and momentum diffusion properties of condensed phase biological fluids. The widely used transient hot-wire technique for determination of thermal diffusion properties is proposed here to investigate also the apparent kinematic viscosity of fluids with the apparatus commonly adopted for thermal conductivity and/or thermal diffusivity determination. The undesired onset of convection in the determination of thermal diffusion properties is in this case the useful effect measured at the wire-fluid interface. From a theoretical point of view, the onset of convection time at a given vertical position along the wire has been related to the Prandtl number, and the reliability of the kinematic viscosity has been studied and preliminarily tested in the case of water.

  18. Studies on coaxial circular array for underwater transducer applications

    Digital Repository Service at National Institute of Oceanography (India)

    Chakraborty, B.

    This thesis presents analytical methods to study important aspects of a coaxial circular array for wideband underwater transducer application. It begins with detailed theoretical study of a coaxial circular array of three turns and an analysis...

  19. Measurement of interfacial toughness of metal film wire and polymer membrane through electricity induced buckling method.

    Science.gov (United States)

    Wang, Qinghua; Xie, Huimin; Lu, Jian; Chen, Pengwan; Zhang, Qingming

    2011-06-15

    Measurement of interfacial toughness of a metal film wire and a flexible substrate is a challenging issue for evaluating the interfacial bonding capacity of the film-wire/substrate systems. In this paper, an electricity induced buckling method is proposed to measure the interfacial toughness between a metal film wire and a polymer membrane, which does not use a pre-existing weak interface. This method relies on causing a buckling driven delamination of the metal film wire from the polymer membrane, by inducing a compressive stress due to electrification of the film wire. For a sort of structure formed by a constantan film wire and a polymer membrane, the current density range under which the buckling of the film wire will emerge is obtained from experiments. The average interfacial toughness of one typical sample is measured to be 31.6 J/m(2). According to the buckling topographies under different current densities, the interfacial toughness of the constantan film wire and the polymer substrate is found to vary from 10 J/m(2) to 60 J/m(2).

  20. Application of Hot-wire Method for Measuring Thermal Conductivity of Fine Ceramics

    Directory of Open Access Journals (Sweden)

    Shangxi WANG

    2016-11-01

    Full Text Available Ceramic substrate is preferred in high density packaging due to its high electrical resistivity and moderate expansion coefficient. The thermal conductivity is a key parameter for packaging substrates. There are two common methods to measure the thermal conductivity, which are the hot-wire method and the laser-flash method. Usually, the thermal conductivities of porcelain is low and meet the measurement range of hot-wire method, and the measured value by hot-wire method has little difference with that by laser-flash method. In recent years, with the requirement of high-powered LED lighting, some kinds of ceramic substrates with good thermal conductivity have been developed and their thermal conductivity always measured by the means of laser flash method, which needs expensive instrument. In this paper, in order to detect the thermal conductivity of fine ceramic with convenience and low cost, the feasibility of replacing the laser flash method with hot wire method to measure thermal conductivity of ceramic composites was studied. The experiment results showed that the thermal conductivity value of fine ceramics measured by the hot-wire method is severely lower than that by the laser-flash method. However, there is a positive relationship between them. It is possible to measure the thermal conductivity of fine ceramic workpiece instantly by hot-wire method via a correction formula.DOI: http://dx.doi.org/10.5755/j01.ms.22.4.12543

  1. Improved method of analyzing hot-wire measurements in supersonic turbulence

    Science.gov (United States)

    Logan, Pamela

    1989-01-01

    The present analysis method for hot-wire data in supersonic turbulence takes sound field effects into account and yields greater accuracy in its treatment of flow variable fluctuations than existing methods despite requiring only a moderately accurate estimate of static pressure fluctuations. The method demonstrates the way in which neglecting pressure fluctuations will affect hot-wire data analysis, as well as indicating the probable direction the errors will take.

  2. Transient Analysis of Lumped Circuit Networks Loaded Thin Wires By DGTD Method

    KAUST Repository

    Li, Ping

    2016-03-31

    With the purpose of avoiding very fine mesh cells in the proximity of a thin wire, the modified telegrapher’s equations (MTEs) are employed to describe the thin wire voltage and current distributions, which consequently results in reduced number of unknowns and augmented Courant-Friedrichs-Lewy (CFL) number. As hyperbolic systems, both the MTEs and the Maxwell’s equations are solved by the discontinuous Galerkin time-domain (DGTD) method. In realistic situations, the thin wires could be either driven or loaded by circuit networks. The thin wire-circuit interface performs as a boundary condition for the thin wire solver, where the thin wire voltage and current used for the incoming flux evaluation involved in the DGTD analyzed MTEs are not available. To obtain this voltage and current, an auxiliary current flowing through the thin wire-circuit interface is introduced at each interface. Corresponding auxiliary equations derived from the invariable property of characteristic variable for hyperbolic systems are developed and solved together with the circuit equations established by the modified nodal analysis (MNA) modality. Furthermore, in order to characterize the field and thin wire interactions, a weighted electric field and a volume current density are added into the MTEs and Maxwell-Ampere’s law equation, respectively. To validate the proposed algorithm, three representative examples are presented.

  3. Cable Crosstalk Suppression with Two-Wire Voltage Feedback Method for Resistive Sensor Array.

    Science.gov (United States)

    Wu, Jianfeng; He, Shangshang; Li, Jianqing; Song, Aiguo

    2016-01-01

    Using a long, flexible test cable connected with a one-wire voltage feedback circuit, a resistive tactile sensor in a shared row-column fashion exhibited flexibility in robotic operations but suffered from crosstalk caused by the connected cable due to its wire resistances and its contacted resistances. Firstly, we designed a new non-scanned driving-electrode (VF-NSDE) circuit using two wires for every row line and every column line to reduce the crosstalk caused by the connected cables in the circuit. Then, an equivalent resistance expression of the element being tested (EBT) for the two-wire VF-NSDE circuit was analytically derived. Following this, the one-wire VF-NSDE circuit and the two-wire VF-NSDE circuit were evaluated by simulation experiments. Finally, positive features of the proposed method were verified with the experiments of a two-wire VF-NSDE prototype circuit. The experiment results show that the two-wire VF-NSDE circuit can greatly reduce the crosstalk error caused by the cables in the 2-D networked resistive sensor array.

  4. Advanced signal processing methods applied to guided waves for wire rope defect detection

    Science.gov (United States)

    Tse, Peter W.; Rostami, Javad

    2016-02-01

    Steel wire ropes, which are usually composed of a polymer core and enclosed by twisted wires, are used to hoist heavy loads. These loads are different structures that can be clamshells, draglines, elevators, etc. Since the loading of these structures is dynamic, the ropes are working under fluctuating forces in a corrosive environment. This consequently leads to progressive loss of the metallic cross-section due to abrasion and corrosion. These defects can be seen in the forms of roughened and pitted surface of the ropes, reduction in diameter, and broken wires. Therefore, their deterioration must be monitored so that any unexpected damage or corrosion can be detected before it causes fatal accident. This is of vital importance in the case of passenger transportation, particularly in elevators in which any failure may cause a catastrophic disaster. At present, the widely used methods for thorough inspection of wire ropes include visual inspection and magnetic flux leakage (MFL). Reliability of the first method is questionable since it only depends on the operators' eyes that fails to determine the integrity of internal wires. The later method has the drawback of being a point by point and time-consuming inspection method. Ultrasonic guided wave (UGW) based inspection, which has proved its capability in inspecting plate like structures such as tubes and pipes, can monitor the cross-section of wire ropes in their entire length from a single point. However, UGW have drawn less attention for defect detection in wire ropes. This paper reports the condition monitoring of a steel wire rope from a hoisting elevator with broken wires as a result of corrosive environment and fatigue. Experiments were conducted to investigate the efficiency of using magnetostrictive based UGW for rope defect detection. The obtained signals were analyzed by two time-frequency representation (TFR) methods, namely the Short Time Fourier Transform (STFT) and the Wavelet analysis. The location of

  5. Method for wiring allocation and switch configuration in a multiprocessor environment

    Science.gov (United States)

    Aridor, Yariv; Domany, Tamar; Frachtenberg, Eitan; Gal, Yoav; Shmueli, Edi; Stockmeyer, legal representative, Robert E.; Stockmeyer, Larry Joseph

    2008-07-15

    A method for wiring allocation and switch configuration in a multiprocessor computer, the method including employing depth-first tree traversal to determine a plurality of paths among a plurality of processing elements allocated to a job along a plurality of switches and wires in a plurality of D-lines, and selecting one of the paths in accordance with at least one selection criterion.

  6. HEAT TRANSFER ANALYSIS OF HEAT GENERATING WIRE USING FINITE ELEMENT METHOD

    OpenAIRE

    Dipak J. Parmar; Bhargav M. Chavda

    2000-01-01

    This paper describes the numerical results of the heat transfer from heat generating wire at different conditions by finite element method. The parametric effects on heat transfer were investigated. The varied parameters included ambient conditions, as well as the shape of the cross-section. The numerical results show that the type of the medium where the heat generating wire immerges has strong effects on the heatdissipation rate. As the size of the diameter the heat dis...

  7. A hot-wire method for high-intensity turbulent flows

    Science.gov (United States)

    Mueller, U. R.

    1983-01-01

    A measuring technique for determing instantaneous, three-dimensional velocity vectors in highly turbulent flows by means of a 4-sensor hot-wire probe is described. As is well known, the hot-wire signal received in reversing flows cannot uniquely be interpreted. This difficulty is circumvented by tracking the thermal wake of a heated wire. Whenever the approximate flow direction is indicated by a temperature-sensitive wake detector, all components of the instantaneous velocity vector are evaluated by means of a digital data reduction method. Uniqueness of the solution derived from the triple-hot-wire response equations is examined. A first application of the proposed measuring technique in the recirculating flow downstream of a backward-facing step is described.

  8. Improved Control Of cheese Manufacture Through continuous Vat Monitoring Of Coagulation Parameters Using The Hot Wire Method

    OpenAIRE

    LeFevre, Michael John

    1995-01-01

    The hot wire method, with pH and temperature sensors, was evaluated to determine its usefulness and application for cheese production automation. Coagulation of milk substrate was measured with the hot wire instrument and by four other methods: Formagraph, Brookfield®, vixcometer, Omnispec™ bioactivity monitor, and Sommer and Matsen rolling bottle method. The hot wire, using the time at maximum slope, detected coagulation before methods that measure resistance to shear, and after methods that...

  9. Methods of Measurement of High Air Velocities by the Hot-wire Method

    Science.gov (United States)

    Weske, John R.

    1943-01-01

    Investigations of strengths of hot wires at high velocities were conducted with platinum, nickel, and tungsten at approximately 200 Degrees Celcius hot-wire temperature. The results appear to disqualify platinum for velocities approaching the sonic range; whereas nickel withstands sound velocity, and tungsten may be used for supersonic velocities under standard atmospheric conditions. Hot wires must be supported by rigid prolongs at high velocities to avoid wire breakage. Resting current measurements for constant temperature show agreement with King's relation.

  10. Lightning Surge Analysis Including Diagonal Wires Based on the FDTD Method

    Science.gov (United States)

    Yamamoto, Kazuo; Iki, Hiroyuki

    This paper presents an arbitrary diagonal wire on an rectangular surface composing a cubic cell in an electromagnetic analysis based on the orthogonal FDTD (Finite-Difference Time-Domain) Algorithm. One of the numerical electromagnetic analyzing algorithms is the FDTD method based on Maxwell’s equation. The basic FDTD method divides the analyzed space into cubic cells and directly calculates the electrical and magnetic fields of the cells by discretizing the Maxwell’s equation of electromagnetic fields, where the derivatives with respect to time and space are replaced by a numerical difference. The development of computer performance brings about an actual execution of the FDTD method on a usual personal computer recently. In dealing with a diagonal and curved wire, the boundaries of which do not coincide with the finite-difference grid lines, the staircase approximation has been commonly used. However, the approximation causes the large error in a resonant frequency and a propagation time of a system including the diagonal or curved wire. The proposed method can express a diagonal and curved wires on a rectangular surface composing a cubic cell by transforming the general integral form of Maxwell’s equation to the different integral form around the wires. This proposed method is also useful to calculate surge propagation on an arbitrary three-dimensional skeleton structure including a diagonal or curved grid such as a tower model and so on.

  11. Fiducialization of the small-aperture quadrupoles based on the vibrating wire method

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Baichuan, E-mail: wangbaichuan@nint.ac.cn [State Key Laboratory of Intense Pulsed Radiation Simulation and Effect (Northwest Institute of Nuclear Technology), Xi' an 710024 (China); Tsinghua University, Beijing 100084 (China); Zheng, Shuxin, E-mail: zhengsx@tsinghua.edu.cn [Tsinghua University, Beijing 100084 (China); Wu, Lin; Du, Changtong; Xing, Qingzi [Tsinghua University, Beijing 100084 (China); Wang, Zhongming; Qiu, Mengtong [State Key Laboratory of Intense Pulsed Radiation Simulation and Effect (Northwest Institute of Nuclear Technology), Xi' an 710024 (China); Wang, Xuewu [Tsinghua University, Beijing 100084 (China)

    2016-03-11

    A fiducialization method based on vibrating wire is described dedicated to the problem of locating the magnetic center relative to external fiducials for the small-aperture quadrupoles. The advantage of this method is that the measurement of the wire position, which may be the main error source, is no longer needed. The position of the magnetic center can be directly obtained by measuring the position shift of the magnet fiducials. This method has been validated on small Permanent Magnet Quadrupoles (PMQs). Experiments have confirmed its feasibility of measuring PMQs with good repeatability of about 10 μm, and shown its high sensitivity as well as convenience.

  12. An Interactive Method Based on the Live Wire for Segmentation of the Breast in Mammography Images

    Directory of Open Access Journals (Sweden)

    Zhang Zewei

    2014-01-01

    Full Text Available In order to improve accuracy of computer-aided diagnosis of breast lumps, the authors introduce an improved interactive segmentation method based on Live Wire. This paper presents the Gabor filters and FCM clustering algorithm is introduced to the Live Wire cost function definition. According to the image FCM analysis for image edge enhancement, we eliminate the interference of weak edge and access external features clear segmentation results of breast lumps through improving Live Wire on two cases of breast segmentation data. Compared with the traditional method of image segmentation, experimental results show that the method achieves more accurate segmentation of breast lumps and provides more accurate objective basis on quantitative and qualitative analysis of breast lumps.

  13. An interactive method based on the live wire for segmentation of the breast in mammography images.

    Science.gov (United States)

    Zewei, Zhang; Tianyue, Wang; Li, Guo; Tingting, Wang; Lu, Xu

    2014-01-01

    In order to improve accuracy of computer-aided diagnosis of breast lumps, the authors introduce an improved interactive segmentation method based on Live Wire. This paper presents the Gabor filters and FCM clustering algorithm is introduced to the Live Wire cost function definition. According to the image FCM analysis for image edge enhancement, we eliminate the interference of weak edge and access external features clear segmentation results of breast lumps through improving Live Wire on two cases of breast segmentation data. Compared with the traditional method of image segmentation, experimental results show that the method achieves more accurate segmentation of breast lumps and provides more accurate objective basis on quantitative and qualitative analysis of breast lumps.

  14. Analysis of pulsed wire method for field integral measurements in undulators

    Indian Academy of Sciences (India)

    Vinit Kumar; Ganeshwar Mishra

    2010-05-01

    Pulsed wire technique is a fast and accurate method for the measurement of first and second field integrals of undulators used in free-electron lasers and synchrotron light sources. In this paper, we present a theoretical analysis of this technique by finding out the analytic solution of the differential equation for the forced vibration of the wire taking dispersion due to stiffness into account. Method of images is used to extend these solutions to include reflections at the ends. For long undulators, the effect of dispersion of the acoustic wave in the wire could be significant and our analysis provides a method for the evaluation of the magnetic field profile even in such cases taking the effect due to dispersion into account in an exact way.

  15. Process improvement in laser hot wire cladding for martensitic stainless steel based on the Taguchi method

    Science.gov (United States)

    Huang, Zilin; Wang, Gang; Wei, Shaopeng; Li, Changhong; Rong, Yiming

    2016-09-01

    Laser hot wire cladding, with the prominent features of low heat input, high energy efficiency, and high precision, is widely used for remanufacturing metal parts. The cladding process, however, needs to be improved by using a quantitative method. In this work, volumetric defect ratio was proposed as the criterion to describe the integrity of forming quality for cladding layers. Laser deposition experiments with FV520B, one of martensitic stainless steels, were designed by using the Taguchi method. Four process variables, namely, laser power ( P), scanning speed ( V s), wire feed rate ( V f), and wire current ( I), were optimized based on the analysis of signal-to-noise (S/N) ratio. Metallurgic observation of cladding layer was conducted to compare the forming quality and to validate the analysis method. A stable and continuous process with the optimum parameter combination produced uniform microstructure with minimal defects and cracks, which resulted in a good metallurgical bonding interface.

  16. Measurements of the Thermal Conductivity and Thermal Diffusivity of Polymer Melts with the Short-Hot-Wire Method

    OpenAIRE

    Wicaksono, Hendro; Zhang, Xing; Fujii, Motoo

    2001-01-01

    In this paper, the thermal conductivity and thermal diffusivity of four kinds of polymer melts were measured by using the transient short-hot-wire method. This method was developed from the hot-wire technique and is based on two-dimensional numerical solutions of unsteady heat conduction from a wire with the same length-to-diameter ratio and boundary conditions as those in the actual experiments. The present method is particularly suitable for measurements of molten polymers where natural con...

  17. Note: effect of the tilting angle of the wire on the onset of natural convection in the transient hot wire method.

    Science.gov (United States)

    Lee, Seung-Hyun; Jang, Seok Pil

    2012-07-01

    In this paper, numerical and experimental investigations are systematically performed to identify the effect of the tilting angle of the wire on the onset of natural convection in the transient hot wire method (THWM), a widely accepted technique for measuring the thermal conductivity of various media, especially nanofluids. To validate our numerical simulation code, the numerical results are compared with theoretical solutions as well as with experimental results. Based on the results, we show that the onset time of natural convection in THWM decreases rapidly with the increase of the wire's tilting angle from vertical position. Also, we systematically show the effect of the wire's tilting angle on the linear region, which is a suitable measurement interval, and on the measurement error of THWM.

  18. Note: Effect of the tilting angle of the wire on the onset of natural convection in the transient hot wire method

    Science.gov (United States)

    Lee, Seung-Hyun; Jang, Seok Pil

    2012-07-01

    In this paper, numerical and experimental investigations are systematically performed to identify the effect of the tilting angle of the wire on the onset of natural convection in the transient hot wire method (THWM), a widely accepted technique for measuring the thermal conductivity of various media, especially nanofluids. To validate our numerical simulation code, the numerical results are compared with theoretical solutions as well as with experimental results. Based on the results, we show that the onset time of natural convection in THWM decreases rapidly with the increase of the wire's tilting angle from vertical position. Also, we systematically show the effect of the wire's tilting angle on the linear region, which is a suitable measurement interval, and on the measurement error of THWM.

  19. Implementation and Applications of the Method of Auxiliary Sources for Analysis of Smooth Scatterers and Wires

    DEFF Research Database (Denmark)

    Larsen, Niels Vesterdal

    2007-01-01

    This report documents the implementation of Method of Auxiliary Sources techniques developed for smooth scatterers and wire scatterers. The work was done in the course of the PhD project "Electronically Steerable Antennas for Satellite Communication" where the techniques were employed to investig......This report documents the implementation of Method of Auxiliary Sources techniques developed for smooth scatterers and wire scatterers. The work was done in the course of the PhD project "Electronically Steerable Antennas for Satellite Communication" where the techniques were employed...

  20. A Novel Method to Obtain Wires Distribution Considering the Shape of Generated Electromagnetic Field

    CERN Document Server

    Hong, Tianqi

    2016-01-01

    This paper proposes a method to calculate the wires distribution for generating required electromagnetic field. Instead of solving the distribution of wires directly, we formulate the problem into zero-one programming form. By applying the proposed algorithm to solve the zero-one programming problem, a practical solution can be obtained. Two practical examples are proposed to illustrate detailed calculation steps of the novel method. The comparison between binary particle swarm optimization searching algorithm and the pro-posed algorithm is provided and discussed. All the design results are validated with FEM calculation results.

  1. Copper sheath MgB{sub 2} wires fabricated by an in situ PIT method

    Energy Technology Data Exchange (ETDEWEB)

    Shimura, S.; Machi, T.; Murakami, M.; Koshizuka, N.; Mochizuki, K.; Ishikawa, I.; Shibata, N

    2004-10-01

    We investigated the applicability of Cu as sheath materials for MgB{sub 2} wires prepared by in situ PIT (powder-in-tube) method in comparison with stainless steal. Since the critical current density of MgB{sub 2} increases with TiH{sub 2} doping, we prepared TiH{sub 2} doped MgB{sub 2} Cu sheath wires 40 m in length and diameter 1.0 mm or 0.5 x 1.0 mm{sup 2} in cross section by rotary swaging, drawing, and two-axial rolling under cold working. We then annealed the samples at 600-850 deg. C for 1-2 h in Ar gas atmosphere. The critical current of TiH{sub 2} (6%) doped MgB{sub 2}/Cu short sample annealed at 650 deg. C reached 208 A (J{sub c}=230 kA/cm{sup 2}) at 4.2 K and self-field. We also fabricated several coils using these wires. The I{sub c} value was {approx}100 A at 4.2 K for a coil prepared with use of a 5 m length wire. These results suggest that it is possible to fabricate Cu sheathed MgB{sub 2} wires with good performance by using the in situ PIT method.

  2. Copper sheath MgB 2 wires fabricated by an in situ PIT method

    Science.gov (United States)

    Shimura, S.; Machi, T.; Murakami, M.; Koshizuka, N.; Mochizuki, K.; Ishikawa, I.; Shibata, N.

    2004-10-01

    We investigated the applicability of Cu as sheath materials for MgB 2 wires prepared by in situ PIT (powder-in-tube) method in comparison with stainless steal. Since the critical current density of MgB 2 increases with TiH 2 doping, we prepared TiH 2 doped MgB 2 Cu sheath wires 40 m in length and ∅ 1.0 mm or 0.5 × 1.0 mm 2 in cross section by rotary swaging, drawing, and two-axial rolling under cold working. We then annealed the samples at 600-850 °C for 1-2 h in Ar gas atmosphere. The critical current of TiH 2 (6%) doped MgB 2/Cu short sample annealed at 650 °C reached 208 A ( Jc=230 kA/cm 2) at 4.2 K and self-field. We also fabricated several coils using these wires. The Ic value was ∼100 A at 4.2 K for a coil prepared with use of a 5 m length wire. These results suggest that it is possible to fabricate Cu sheathed MgB 2 wires with good performance by using the in situ PIT method.

  3. Joining characteristics of titanium-based orthodontic wires connected by laser and electrical welding methods.

    Science.gov (United States)

    Matsunaga, Junko; Watanabe, Ikuya; Nakao, Noriko; Watanabe, Etsuko; Elshahawy, Waleed; Yoshida, Noriaki

    2015-01-01

    This study investigated the possibility of electrical and laser welding to connect titanium-based alloy (beta-titanium and nickel-titanium) wires and stainless-steel or cobalt-chromium alloy wires for fabrication of combination arch-wires. Four kinds of straight orthodontic rectangular wires (0.017 × 0.025 inch) were used: stainless-steel (S-S), cobalt-chromium (Co-Cr), beta-titanium alloy (β-Ti), and nickel-titanium (Ni-Ti). Homogeneous and heterogeneous end-to-end joints (15 mm long each) were made by electrical welding and laser welding. Non-welded wires (30 mm long) were also used as a control. Maximum loads at fracture (N) and elongation (%) were measured by conducting tensile test. The data (n = 10) were statistically analyzed using analysis of variance/Tukey test (P welding and those of the S-S/S-S and Co-Cr/Co-Cr specimens welded by laser. On the other hand, the laser-welded Ni-Ti/Ni-Ti and β-Ti/β-Ti specimens exhibited higher values of the ML and EL compared to those of the corresponding specimens welded by electrical method. In the heterogeneously welded combinations, the electrically welded Ni-Ti/S-S, β-Ti/S-S and β-Ti/Co-Cr specimens showed significantly (P welded by laser. Electrical welding exhibited the higher values of maximum load at fracture and elongation for heterogeneously welded combinations than laser-welding.

  4. Optimizing SUS 304 wire drawing process by grey relational analysis utilizing Taguchi method

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    In the stainless steel 304 (SUS 304) wire drawing process,optimizing the die life and wire tensile strength,which are the larger-the-better quality characteristics (QCH) types,is of main interest.Three control factors,involving reduction ratio,lubricant temperature,and drawing speed,were investigated utilizing L9(34) orthogonal array (OA).The grey relational analysis was conducted for the normalized signal-to-noise (S/N) ratios.The ordinal value of the grey grade was then used to decide optimal factor levels.The anticipated improvements in die life and wire tensile strength were estimated 25.31 h and 22.50 kg/mm2,respectively.To decide the significant factor which had effect on each QCH and predict the average value of each QCH,analysis of variance (ANOVA) was performed for S/N ratio and QCH.Confurmation experiments were then conducted,where a good overlap was noticed between the predicted and confirmation intervals for each QCH.The Hotelling 72 and the sample generalized variance control charts were finally utilized in controlling and monitoring future production.In conclusion,the grey relational analysis utilizing Taguchi method is an effective approach for optimizing the die life and wire tensile strength for SUS wire drawing process.

  5. Supercondcuting properties in MgB2/Fe wires prepared by PIT method

    Institute of Scientific and Technical Information of China (English)

    YAN Guo; FENG Yong; FU Baoquan; LIU Chunfang; JI Ping; ZHANG Pingxiang; ZHOU Lian

    2003-01-01

    The MgB2 formation was analyzed physically and chemically and the MgB2/Fe wires were fabricated by powder in tube (PIT) technology. The microstructureof MgB2 in wires was studied by the scanning electrical microscope (SEM), whichshows a good connection of grains and the size of MgB2 grain is 1-3μm. The results of Jc measured by the standard four probes method show that Jc value reaches 6.1×104 A/cm2 at 20 K in self field.

  6. Novel Gas Barrier SiOC Coating to PET Bottles through a Hot Wire CVD Method

    Directory of Open Access Journals (Sweden)

    Masaki Nakaya

    2016-01-01

    Full Text Available In an attempt to enhance the gas barrier enhancement of plastic containers such as poly(ethylene terephthalate bottles, a novel method was found using a hot wire CVD technique, where tantalum wire is heated and exposed to a gas flow of vinyl silane. The resultant SiOC thin film was confirmed to characteristically contain Si-Si bonds in its surface and demonstrate a remarkably and highly practical decrease of the permeation of various gas through poly(ethylene terephthalate bottles.

  7. Synthesis of Ultradisperse Carbon Dioxide Powder with Plasma-Dynamic Method in the Coaxial Magneto-Plasma Accelerator

    Directory of Open Access Journals (Sweden)

    Golyanskaya Evgeniya. O.

    2016-01-01

    Full Text Available One of the most promising trends in modern physics is the high-temperature superconductivity. Analysis of high-temperature superconductors revealed that almost all of them are complex copper-based oxides. Studies have shown the possibility of using them for the synthesis of coaxial magneto accelerator. Studies have identified the products synthesized soot: Cu, Cu2O, CuO, their shape and size. Also been deciphered and electron microscopy confirmed the composition of the nanopowder obtained in laboratory conditions.

  8. Generation of nano-sized core-shell particles using a coaxial tri-capillary electrospray-template removal method.

    Science.gov (United States)

    Cao, Lihua; Luo, Jun; Tu, Kehua; Wang, Li-Qun; Jiang, Hongliang

    2014-03-01

    This study proposed a new strategy based on a coaxial tri-capillary electrospray-template removal process for producing nanosized polylactide-b-polyethylene glycol (PLA-PEG) particles with a core-shell structure. Microparticles with core-shell-corona structures were first fabricated by coaxial tri-capillary electrospray, and core-shell nanoparticles less than 200 nm in size were subsequently obtained by removing the PEG template from the core-shell-corona microparticles. The nanoparticle size could be modulated by adjusting the flow rate of corona fluid, and nanoparticles with an average diameter of 106±5 nm were obtained. The nanoparticles displayed excellent dispersion stability in aqueous media and very low cytotoxicity. Paclitaxel was used as a model drug to be incorporated into the core section of the nanoparticles. A drug loading content in the nanoparticles as high as 50.7±1.5 wt% with an encapsulation efficiency of greater than 70% could be achieved by simply increasing the feed rate of the drug solution. Paclitaxel exhibited sustained release from the nanoparticles for more than 40 days. The location of the paclitaxel in the nanoparticles, i.e., in the core or shell layer, did not have a significant effect on its release.

  9. Non-invasive hyperthermia apparatus including coaxial applicator having a non-invasive radiometric receiving antenna incorporated therein and method of use thereof

    Science.gov (United States)

    Ross, M.P.

    1996-08-27

    A coaxial hyperthermia applicator is disclosed for applying non-invasively electromagnetic energy to a body against which it is placed. The coaxial applicator antenna has formed integrally within it a non-invasive radiometric antenna for receiving thermoelectromagnetic emissions. The coaxial-configured applicator produces a bell-shaped radiation pattern symmetric about the axis of symmetry of the coaxial applicator. Integrating the radiometric antenna within the coaxial applicator produces a single device that performs dual functions. The first function is to transmit non-invasively energy for heating a subcutaneous tumor. The second function is to receive non-invasively thermal electromagnetic radiation from the tumor by which temperature is sensed and fed back to control the output of the coaxial applicator. 11 figs.

  10. Application of statistical methods at copper wire manufacturing

    Directory of Open Access Journals (Sweden)

    Z. Hajduová

    2009-01-01

    Full Text Available Six Sigma is a method of management that strives for near perfection. The Six Sigma methodology uses data and rigorous statistical analysis to identify defects in a process or product, reduce variability and achieve as close to zero defects as possible. The paper presents the basic information on this methodology.

  11. Coaxial foilless diode

    OpenAIRE

    Long Kong; QingXiang Liu; XiangQiang Li; ShaoMeng Wang

    2014-01-01

    A kind of coaxial foilless diode is proposed in this paper, with the structure model and operating principle of the diode are given. The current-voltage relation of the coaxial foilless diode and the effects of structure parameters on the relation are studied by simulation. By solving the electron motion equation, the beam deviation characteristic in the presence of external magnetic field in transmission process is analyzed, and the relationship between transverse misalignment with diode par...

  12. Coaxial foilless diode

    OpenAIRE

    Long Kong; QingXiang Liu; XiangQiang Li; ShaoMeng Wang

    2014-01-01

    A kind of coaxial foilless diode is proposed in this paper, with the structure model and operating principle of the diode are given. The current-voltage relation of the coaxial foilless diode and the effects of structure parameters on the relation are studied by simulation. By solving the electron motion equation, the beam deviation characteristic in the presence of external magnetic field in transmission process is analyzed, and the relationship between transverse misalignment with diode par...

  13. 激光光内复合送粉送丝熔覆气固两相流流场数值模拟%Numerical Simulation of Gas-Solid Two-Phase Flow Field of Laser Cladding with Coaxial Inside-Beam Composite Powder and Wire Feeding

    Institute of Scientific and Technical Information of China (English)

    石拓; 王永康; 傅戈雁

    2013-01-01

    In this study,using dispersed phase model in ANSYS FLUENT 12.0,the gas-solid two-phase flow field of the developed new type of laser coaxial inside-beam composite powder and wire feeding is three-dimensionally numerically simulated.The effects on the flow field from inlet pressure of shielding gas and the carrier gas flow rate are analyzed.The simulation results indicate that during the coaxial inside-beam powder and wire feeding laser cladding,peripheral shielding gas has very good concentration and collimation effects on the powder beam.The higher the inlet pressure of shielding gas is,the better the powder beam is concentrated.However,too high carrier gas flow rate leads to an enlarged divergence angle of the powder grain flow which is a little far from the composite nozzle.%应用ANSYS FLUENT 12.0软件的离散相模型,对研制的新型激光光内送粉、送丝复合喷嘴气固两相流流场进行了三维数值模拟,分析了保护气入口压力、载气流量等参数对流场的影响.模拟结果表明:激光光内送粉、送丝熔覆时,外围保护气对粉束有很好的集束、准直作用.保护气入口压力越大,粉末的集束效果越明显.而载气流量过大将造成粉末颗粒流在离喷嘴较远处发散角变大.

  14. Numerical implementations of an iterative method with boundary condition splitting as applied to the nonstationary stokes problem in the gap between coaxial cylinders

    Science.gov (United States)

    Solov'ev, M. B.

    2010-11-01

    Numerical implementations of a new fast-converging iterative method with boundary condition splitting are constructed for solving the Dirichlet initial-boundary value problem for the nonstationary Stokes system in the gap between two coaxial cylinders. The problem is assumed to be axially symmetric and periodic along the cylinders. The construction is based on finite-difference approximations in time and bilinear finite-element approximations in a cylindrical coordinate system. A numerical study has revealed that the iterative methods constructed have fairly high convergence rates that do not degrade with decreasing viscosity (the error is reduced by approximately 7 times per iteration step). Moreover, the methods are second-order accurate with respect to the mesh size in the max norm for both velocity and pressure.

  15. Optimization of experimental conditions of hot wire method in thermal conductivity measurements

    OpenAIRE

    Ma, Luyao

    2012-01-01

    This work studied the hot wire method in measuring thermal conductivity at room temperature. The purpose is to find the optimized experimental conditions to minimize natural convection in liquid for this method, which will be taken as reference for high temperature thermal conductivity measurement of slag. Combining room temperature experiments and simulation with COMSOL Multiphysics 4.2a, the study on different experimental parameters which may influence the accuracy of the measured thermal ...

  16. Development of absolute hot-wire anemometry by the 3omega method.

    Science.gov (United States)

    Heyd, Rodolphe; Hadaoui, Abdallah; Fliyou, Mohamed; Koumina, Abdelaziz; El Hassani Ameziane, Lahcen; Outzourhit, Abdelkader; Saboungi, Marie-Louise

    2010-04-01

    We have developed hot-wire anemometry applying the 3omega method. The approach is based on the same heat transfer process as traditional anemometry, but substituting the constant current by a sinusoidal current and using synchronous detection to measure the conductive-convective exchange coefficient and the gas flow rate. Our theoretical model is tested with air flow at 300 K under atmospheric pressure: The experimental results are in agreement with the numerical simulation, justifying the technical choices in the 3omega method and the approximations made. The effectiveness of the 3omega method for measuring the flow rate and the conductive-convective exchange coefficient between the hot wire and flowing gas is discussed.

  17. Development of absolute hot-wire anemometry by the 3ω method

    Science.gov (United States)

    Heyd, Rodolphe; Hadaoui, Abdallah; Fliyou, Mohamed; Koumina, Abdelaziz; Ameziane, Lahcen El Hassani; Outzourhit, Abdelkader; Saboungi, Marie-Louise

    2010-04-01

    We have developed hot-wire anemometry applying the 3ω method. The approach is based on the same heat transfer process as traditional anemometry, but substituting the constant current by a sinusoidal current and using synchronous detection to measure the conductive-convective exchange coefficient and the gas flow rate. Our theoretical model is tested with air flow at 300 K under atmospheric pressure: The experimental results are in agreement with the numerical simulation, justifying the technical choices in the 3ω method and the approximations made. The effectiveness of the 3ω method for measuring the flow rate and the conductive-convective exchange coefficient between the hot wire and flowing gas is discussed.

  18. Novel method and experimental validation of statistical calibration via Gaussianization in hot-wire anemometry

    Science.gov (United States)

    Gluzman, Igal; Cohen, Jacob; Oshman, Yaakov

    2016-11-01

    We introduce a statistical method based on Gaussianization to estimate the nonlinear calibration curve of a hot-wire probe, that relates the input flow velocity to the output (measured) voltage. The method uses as input a measured sequence of voltage samples, corresponding to different unknown flow velocities in the desired operational range, and only two measured voltages along with their known (calibrated) flow velocities. The novel method is validated against standard calibration methods using data acquired by hot-wire probes using wind-tunnel experiments. We demonstrate our new calibration technique by placing the hot-wire probe at certain region downstream of a cube-shaped body in a free stream of air flow. For testing our calibration method we rely on flow statistics that exist, among others, in a certain region of a turbulent wake formed downstream of the cube-shaped body. The specific properties are: first, the velocity signal in the wake should be as close to Gaussian as possible. Second, the signal should cover the desired velocity range that should be calibrated. The appropriate region to place our probe is determined via computation of the first four statistical moments of the measured signals in different regions of the wake.

  19. Calibration and Measurement in Turbulence Research by the Hot-Wire Method

    Science.gov (United States)

    Kovasznay, Kaszlo

    1947-01-01

    The problem of turbulence in aerodynamics is at present being attacked both theoretically and experimentally. In view of the fact however that purely theoretical considerations have not thus far led to satisfactory results the experimental treatment of the problem is of great importance. Among the different measuring procedures the hot wire methods are so far recognized as the most suitable for investigating the turbulence structure. The several disadvantages of these methods however, in particular those arising from the temperature lag of the wire can greatly impair the measurements and may easily render questionable the entire value of the experiment. The name turbulence is applied to that flow condition in which at any point of the stream the magnitude and direction of the velocity fluctuate arbitrarily about a well definable mean value. This fluctuation imparts a certain whirling characteristic to the flow.

  20. Effect of wire shape on wire array discharge

    Energy Technology Data Exchange (ETDEWEB)

    Shimomura, N.; Tanaka, Y.; Yushita, Y.; Nagata, M. [University of Tokushima, Department of Electrical and Electronic Engineering, Tokushima (Japan); Teramoto, Y.; Katsuki, S.; Akiyama, H. [Kumamoto University, Department of Electrical and Computer Engineering, Kumamoto (Japan)

    2001-09-01

    Although considerable investigations have been reported on z-pinches to achieve nuclear fusion, little attention has been given from the point of view of how a wire array consisting of many parallel wires explodes. Instability existing in the wire array discharge has been shown. In this paper, the effect of wire shape in the wire array on unstable behavior of the wire array discharge is represented by numerical analysis. The claws on the wire formed in installation of wire may cause uniform current distribution on wire array. The effect of error of wire diameter in production is computed by Monte Carlo Method. (author)

  1. Hot-Wire Calibration at Low Velocities: Revisiting the Vortex Shedding Method

    OpenAIRE

    Sattarzadeh, Sohrab S.; Athanasia Kalpakli; Ramis Örlü

    2013-01-01

    The necessity to calibrate hot-wire probes against a known velocity causes problems at low velocities, due to the inherent inaccuracy of pressure transducers at low differential pressures. The vortex shedding calibration method is in this respect a recommended technique to obtain calibration data at low velocities, due to its simplicity and accuracy. However, it has mainly been applied in a low and narrow Reynolds number range known as the laminar vortex shedding regime. Here, on the other ha...

  2. A novel method for harmless disposal and resource reutilization of steel wire rope sludges.

    Science.gov (United States)

    Zhang, Li; Liu, Yang-Sheng

    2016-10-01

    Rapid development of steel wire rope industry has led to the generation of large quantities of pickling sludge, which causes significant ecological problems and considerable negative environmental effects. In this study, a novel method was proposed for harmless disposal and resource reutilization of the steel wire rope sludge. Based on the method, two steel wire rope sludges (the Pb sludge and the Zn sludge) were firstly extracted by hydrochloric or sulfuric acid and then mixed with the hydrochloride acid extracting solution of aluminum skimmings to produce composite polyaluminum ferric flocculants. The optimum conditions (acid concentration, w/v ratio, reaction time, and reaction temperature) for acid extraction of the sludges were studied. Results showed that 97.03 % of Pb sludge and 96.20 % of Zn sludge were extracted. Leaching potential of the residues after acid extraction was evaluated, and a proposed treatment for the residues had been instructed. The obtained flocculant products were used to purify the real domestic wastewater and showed an equivalent or better performance than the commercial ones. This method is environmental-friendly and cost-effective when compared with the conventional sludge treatments.

  3. Three-stage Method for Identifying the Dynamic Model Parameters of Stranded Wire Helical Springs

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yu; WANG Shilong; ZHOU Jie; LI Chuan; SUN Shouli

    2015-01-01

    The dynamic behavior of the stranded wire helical spring is described by a modified Bouc-Wen model while the model parameters must be identified using an identification method and experimental data. Existing identification methods usually relies either solely nonlinear iterative algorithms or manually trial and error. Therefore, the identification process can be rather time consuming and effort taking. As a result, these methods are not ideal for engineering applications. To come up with a more practical method, a three-stage identification method is proposed. Periodic loading and identification simulations are carried out to verify the effectiveness of the proposed method. Noises are added to the simulated data to test the performance of the proposed method when dealing with noise contaminated data. The simulation results indicate that the proposed method is able to give satisfying results when the noise levels are set to be 0.01, 0.03, 0.05 and 0.07. In addition, the proposed method is also applied to experimental data and compared with an existing method. The experimental data is acquired through a periodic loading test. The experiment results suggest that the proposed method features better accuracy compared with the existing method. An effective approach is proposed for identifying the model parameters of the stranded wire helical spring.

  4. Apparatus and method for pulsed laser deposition of materials on wires and pipes

    Science.gov (United States)

    Fernandez, Felix E. (Inventor)

    2003-01-01

    Methods and apparatuses are disclosed which allow uniform coatings to be applied by pulsed laser deposition (PLD) on inner and outer surfaces of cylindrical objects, such as rods, pipes, tubes, and wires. The use of PLD makes this technique particularly suitable for complex multicomponent materials, such as superconducting ceramics. Rigid objects of any length, i.e., pipes up to a few meters, and with diameters from less than 1 centimeter to over 10 centimeters can be coated using this technique. Further, deposition is effected simultaneously onto an annular region of the pipe wall. This particular arrangement simplifies the apparatus, reduces film uniformity control difficulties, and can result in faster operation cycles. In addition, flexible wires of any length can be continuously coated using the disclosed invention.

  5. Transient Response of Thin Wire above a Layered Half-Space Using TDIE/FDTD Hybrid Method

    Directory of Open Access Journals (Sweden)

    Bing Wei

    2012-01-01

    Full Text Available The TDIE/FDTD hybrid method is applied to calculate the transient responses of thin wire above a lossy layered half-space. The time-domain reflection of the layered half space is computed by one-dimensional modified FDTD method. Then, transient response of thin wire induced by two excitation sources (the incident wave and reflected wave is calculated by TDIE method. Finally numerical results are given to illustrate the feasibility and high efficiency of the presented scheme.

  6. Structure of Polymer Fibers Fabricated by Electrospinning Method Utilizing a Metal Wire Electrode in a Capillary Tube

    Science.gov (United States)

    Onozuka, Shintaro; Hoshino, Rikiya; Mizuno, Yoshinori; Shinbo, Kazunari; Ohdaira, Yasuo; Baba, Akira; Kato, Keizo; Kaneko, Futao

    We fabricated electrospun poly (vinylalcohol) (PVA) fibers using a copper wire electrode in Teflon capillary tube, and the SEM images were observed. The apparatus in this method is reasonable, and needed volume of polymer solution and distance between the electrodes can be largely reduced compared to conventional method. The wire electrode tip position in the capillary tube is also important in this method and should be close to the polymer solution surface.

  7. Further elucidation of nanofluid thermal conductivity measurement using a transient hot-wire method apparatus

    Science.gov (United States)

    Yoo, Donghoon; Lee, Joohyun; Lee, Byeongchan; Kwon, Suyong; Koo, Junemo

    2017-08-01

    The Transient Hot-Wire Method (THWM) was developed to measure the absolute thermal conductivity of gases, liquids, melts, and solids with low uncertainty. The majority of nanofluid researchers used THWM to measure the thermal conductivity of test fluids. Several reasons have been suggested for the discrepancies in these types of measurements, including nanofluid generation, nanofluid stability, and measurement challenges. The details of the transient hot-wire method such as the test cell size, the temperature coefficient of resistance (TCR) and the sampling number are further investigated to improve the accuracy and consistency of the measurements of different researchers. It was observed that smaller test apparatuses were better because they can delay the onset of natural convection. TCR values of a coated platinum wire were measured and statistically analyzed to reduce the uncertainty in thermal conductivity measurements. For validation, ethylene glycol (EG) and water thermal conductivity were measured and analyzed in the temperature range between 280 and 310 K. Furthermore, a detailed statistical analysis was conducted for such measurements, and the results confirmed the minimum number of samples required to achieve the desired resolution and precision of the measurements. It is further proposed that researchers fully report the information related to their measurements to validate the measurements and to avoid future inconsistent nanofluid data.

  8. [Universal coaxial anesthetic system].

    Science.gov (United States)

    Ungerer, M J; le Roux, F P

    1978-02-25

    A true universal co-axial anaesthetic system has been designed. This system may be used either as a Mapleson A circuit during spontaneous ventilation or as a Mapleson D circuit during controlled ventilation. Conversion to either system may be conveniently carried out by interchanging the pop-off valve and fresh gas inlet, without disconnecting the system from the patient. Resistance to flow of both tubes has been measured and was found to be within acceptable limits. The efficiency of this system in a Mapleson A arrangement was compared with that of a conventional Magill circuit during spontaneous breathing in 2 conscious volunteers. It was shown that no significant difference exists between these systems eith regard to rebreathing, and that the universal co-axial system may be used as efficiently and economically as the Magill circuit during spontaneous ventilation. The co-axial system can be easily connected to a circle system, combining the advantages of the two systems.

  9. Application of PTCA steerable guide wire for abdominal and peripheral interventional angiography

    Energy Technology Data Exchange (ETDEWEB)

    Kuribayashi, Sachio; Ootaki, Makoto; Iwata, Yoshirou; Harada, Tsumio; Tsuji, Makoto; Matsuyama, Seiya

    1988-06-01

    Steerable guide wire used in PTCA was applied for various abdominal and peripheral interventional angiographies in eight patients. In embolization procedures, this wire was used with coaxial catheter system. The steerable wire facilitated superselective catheterization of distal branches in mesenteric, renal and hepatic artery embolizations. This wire was also useful for traversing severe stenoses in renal and peripheral angioplasties.

  10. Coaxial foilless diode

    Directory of Open Access Journals (Sweden)

    Long Kong

    2014-05-01

    Full Text Available A kind of coaxial foilless diode is proposed in this paper, with the structure model and operating principle of the diode are given. The current-voltage relation of the coaxial foilless diode and the effects of structure parameters on the relation are studied by simulation. By solving the electron motion equation, the beam deviation characteristic in the presence of external magnetic field in transmission process is analyzed, and the relationship between transverse misalignment with diode parameters is obtained. These results should be of interest to the area of generation and propagation of radial beam for application of generating high power microwaves.

  11. RESEARCH OF THE FEEDING SPEED ADOPTING CORED-WIRE METHOD TO SPHEROIDIZE DUCTILE IRON MELT

    Institute of Scientific and Technical Information of China (English)

    G.W.Chang; H.X.Wang; X.D.Yue; H.L.Zhang

    2008-01-01

    For settling the question of feeding speed in applying the cored-wire method to spheroidize ductile iron melt, ANSYS software was applied to simulate the heat transfer and mass transfer, and the melt time of the steel strip in the iron melt was determined by linking the heat transfer and mass transfer, and then the feeding speed was calculated. Conclusions have been drawn that the iron layer was formed on the surface of the cored-wire during the wire-feeding process. The thickness is 0.073 mm when the temperature of the iron melt is 1500℃, the time from formation to remelting of the iron layer is 0.063 s. When the temperature of the iron melt is below 1500℃, the time taken for the steel strip to melt is rapidly shortened. When the temperature of the iron melt is above 1500℃, the variation amplitude of the steel strip melt change with time is gradually diminished. The melt time of the steel strip is rapidly increased with the increase of the steel strip thickness. When the temperature of the iron melt is 1500℃ and the carbon content is 4%, the melt time of a steel strip, which has a thickness of 0.5 mm, is thrice that of a steel strip whose thickness is 0.3 mm. The calculation results of the feeding speed are basically in agreement with the applied feeding speed in the factory.

  12. Distributed Capacitance of Coaxial Line With Perturbed Walls

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Perturbation method of boundary geometry(PMOBG) used in Laplacian problems is dealt with and the three-term perturbation expression of distributed capacitance of a coaxial line with perturbed walls is obtained. As an example,four-order expression of distributed capacitance of a elliptic coaxial line with small eccentricity is given.

  13. Design of a Compact Coaxial Magnetized Plasma Gun for Magnetic Bubble Expansion Experiments

    Science.gov (United States)

    2009-06-01

    COAXIAL MAGNETIZED PLASMA GUN FOR MAGNETIC BUBBLE EXPANSION EXPERIMENTS Y. Zhang1, A. G. Lynn1, S. C. Hsu2, M. Gilmore1, C... coaxial magnetized plasma gun and its associated hardware systems are discussed in detail. The plasma gun is used for experimental studies of...and coaxial plasma guns - which is the method employed in this work. The first coaxial plasma gun experiment was performed five decades ago by

  14. Parametric Optimization of Wire Electrical Discharge Machining of Powder Metallurgical Cold Worked Tool Steel using Taguchi Method

    Science.gov (United States)

    Sudhakara, Dara; Prasanthi, Guvvala

    2016-08-01

    Wire Cut EDM is an unconventional machining process used to build components of complex shape. The current work mainly deals with optimization of surface roughness while machining P/M CW TOOL STEEL by Wire cut EDM using Taguchi method. The process parameters of the Wire Cut EDM is ON, OFF, IP, SV, WT, and WP. L27 OA is used for to design of the experiments for conducting experimentation. In order to find out the effecting parameters on the surface roughness, ANOVA analysis is engaged. The optimum levels for getting minimum surface roughness is ON = 108 µs, OFF = 63 µs, IP = 11 A, SV = 68 V and WT = 8 g.

  15. Study of Electromagnetic Scattering From Material Object Doped Randomly With Thin Metallic Wires Using Finite Element Method

    Science.gov (United States)

    Deshpande, Manohar D.

    2005-01-01

    A new numerical simulation method using the finite element methodology (FEM) is presented to study electromagnetic scattering due to an arbitrarily shaped material body doped randomly with thin and short metallic wires. The FEM approach described in many standard text books is appropriately modified to account for the presence of thin and short metallic wires distributed randomly inside an arbitrarily shaped material body. Using this modified FEM approach, the electromagnetic scattering due to cylindrical, spherical material body doped randomly with thin metallic wires is studied.

  16. The collinear coaxial array antenna

    Science.gov (United States)

    Brammer, D. J.; Williams, D.

    1981-03-01

    A design of a coaxial vertical antenna proposed in the ARRL antenna handbook is analyzed. A numerical analysis was carried out using the moment method. A variety of antenna configurations in the 160 MHz design frequency are analyzed and current distribution, gain, polar diagrams and impedances are calculated. The analysis is carried out for simple configurations and extended to a case with 16 repeated center sections. The effects of using lossy cable in the construction is also investigated. A defect in the original ARRL design is rectified. An array of an overall length 5.33 wavelengths is shown to have a gain of 10.69 dB.

  17. Measurements of thermal conductivity and thermal diffusivity of hen egg-white lysozyme crystals using a short hot wire method

    Science.gov (United States)

    Fujiwara, Seiji; Maki, Syou; Tanaka, Seiichi; Maekawa, Ryunosuke; Masuda, Tomoki; Hagiwara, Masayuki

    2017-07-01

    Thermal conductivity and thermal diffusivity of hen egg-white lysozyme (HEWL) crystals were examined by using the transient short hot wire method. This method is based on the conventional hot wire method, but improved by using a wire that is much shorter than conventional ones. The magneto-Archimedes levitation technique was utilized to attach the HEWL crystals onto the wire. Owing to the upward magnetic force, the HEWL crystals were deposited at the air-liquid interface of the protein buffer solution where the short hot wire was preliminarily fixed. In situ observation clarified that the wire was completely buried into the HEWL crystals. By means of these techniques, the measurement of thermal conductivity and thermal diffusivity of HEWL crystals was realized for the first time. Gadolinium chloride (a paramagnetic subject) was used as a precipitant agent of crystallization. Crystal growth was carried out over 20 h at 17.2 °C. The applied magnetic field was 4 T. Measurements were conducted during the crystal growth at two different times. The thermal conductivity and diffusivity of the HEWL crystals were determined to be 0.410 W/(m.K) and 3.77×10-8 m2/s at 14 h after, and 0.438 W/(m.K) and 5.18×10-8 m2/s at 20 h after, respectively. We emphasize that this method is versatile and applicable for other protein crystals.

  18. Modern Cored Wire Injection 2PE-9 Method in the Production of Ductile Iron

    Directory of Open Access Journals (Sweden)

    E. Guzik

    2012-04-01

    Full Text Available The results of studies on the use of modern two cored wires injection method for production of nodular graphite cast iron with use of unique implementation of drum ladle as a treatment/ transport and casting ladle instead vertical treatment ladle was described. The injection of length of Ø 9mm wires, cored: in FeSi + Mg nodulariser mixture and inoculant master alloy is a treatment method which can be used to produce iron melted in coreless induction furnace. This paper describes the results of using this method for possibility production of ductile iron under specific industrial conditions. In this case was taken ductile iron with material designation: EN-GJS-450- 10 Grade according PN-EN 1563:2000. Microstructure of 28 trials was controlled on internally used sample which has been correlated with standard sample before. The paper presents typical metallic matrix and graphite characteristic. Additionally, mechanical properties were checked in one experiment. Because of further possibility treatment temperature reduction only the rough magnesium recovery and cost of this new method are given.

  19. Method for reuse of wafers for growth of vertically-aligned wire arrays

    Science.gov (United States)

    Spurgeon, Joshua M; Plass, Katherine E; Lewis, Nathan S; Atwater, Harry A

    2013-06-04

    Reusing a Si wafer for the formation of wire arrays by transferring the wire arrays to a polymer matrix, reusing a patterned oxide for several array growths, and finally polishing and reoxidizing the wafer surface and reapplying the patterned oxide.

  20. Hot-Wire Calibration at Low Velocities: Revisiting the Vortex Shedding Method

    Directory of Open Access Journals (Sweden)

    Sohrab S. Sattarzadeh

    2013-01-01

    Full Text Available The necessity to calibrate hot-wire probes against a known velocity causes problems at low velocities, due to the inherent inaccuracy of pressure transducers at low differential pressures. The vortex shedding calibration method is in this respect a recommended technique to obtain calibration data at low velocities, due to its simplicity and accuracy. However, it has mainly been applied in a low and narrow Reynolds number range known as the laminar vortex shedding regime. Here, on the other hand, we propose to utilize the irregular vortex shedding regime and show where the probe needs to be placed with respect to the cylinder in order to obtain unambiguous calibration data.

  1. Feasibility of an electromagnetic compatibility method for MRgFUS using a wire mesh screen.

    Science.gov (United States)

    Wu, Hao; Shen, Guofeng; Chen, Yazhu

    2016-12-01

    This study evaluated an electromagnetic compatibility method for high-intensity focused ultrasound (HIFU) and magnetic resonance (MR) imaging in an MR-guided focused ultrasound surgery using a conductive wire mesh screen. This screen has a good ultrasound transmission and shielding effectiveness. A hybrid acoustic simulation method was developed to analyze the effects of mesh parameters and the HIFU working frequency on the acoustic field. Experiments were performed to measure both acoustic pressure profile and radiated electromagnetic noise. With the proposed mesh screen, the electromagnetic radiation emission was reduced by 14dB at 128MHz while the acoustic focal intensity was reduced by less than 11% using one screen. This shielding method is easy to implement and requires no additional phase correction method. This method also improves the quality of MR images.

  2. High power coaxial ubitron

    Science.gov (United States)

    Balkcum, Adam J.

    In the ubitron, also known as the free electron laser, high power coherent radiation is generated from the interaction of an undulating electron beam with an electromagnetic signal and a static periodic magnetic wiggler field. These devices have experimentally produced high power spanning the microwave to x-ray regimes. Potential applications range from microwave radar to the study of solid state material properties. In this dissertation, the efficient production of high power microwaves (HPM) is investigated for a ubitron employing a coaxial circuit and wiggler. Designs for the particular applications of an advanced high gradient linear accelerator driver and a directed energy source are presented. The coaxial ubitron is inherently suited for the production of HPM. It utilizes an annular electron beam to drive the low loss, RF breakdown resistant TE01 mode of a large coaxial circuit. The device's large cross-sectional area greatly reduces RF wall heat loading and the current density loading at the cathode required to produce the moderate energy (500 keV) but high current (1-10 kA) annular electron beam. Focusing and wiggling of the beam is achieved using coaxial annular periodic permanent magnet (PPM) stacks without a solenoidal guide magnetic field. This wiggler configuration is compact, efficient and can propagate the multi-kiloampere electron beams required for many HPM applications. The coaxial PPM ubitron in a traveling wave amplifier, cavity oscillator and klystron configuration is investigated using linear theory and simulation codes. A condition for the dc electron beam stability in the coaxial wiggler is derived and verified using the 2-1/2 dimensional particle-in-cell code, MAGIC. New linear theories for the cavity start-oscillation current and gain in a klystron are derived. A self-consistent nonlinear theory for the ubitron-TWT and a new nonlinear theory for the ubitron oscillator are presented. These form the basis for simulation codes which, along

  3. Macro-micromechanical approaches for non-coaxiality of coarse grained soils

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    For coarse grained soils,their principal stress directions may change when the water level of embankment dam varies instantaneously.In this loading case,the principal directions of stress and strain rate will become non-coaxial.In an effort to model non-coaxial behavior,a modified three-dimensional non-coaxial model is developed in the context of vertex yield(tangent plasticity) theory.Discrete Element Method(PFC) incorporating user-defined interparticle contact models is also employed to gain an insight into microscopic mechanism of non-coaxiality.The analysis focuses on non-coaxial behaviors under simple shear condition.It has been shown that the proposed non-coaxial model gives good predictions for non-coaxiality with reference to microscopic observations while the classical coaxial model fails to simulate the non-coaxial behaviors.In general,non-coaxiality as a result of the rotation of principal stress,is large at a small shear strain,and inclined to become negligible with increasing shear strain.For coarse grained soils,their non-coaxiality tends to largely depend on the initial normal pressure,where a larger degree of non-coaxiality can be observed at a higher pressure.

  4. A hot-wire method based thermal conductivity measurement apparatus for teaching purposes

    Science.gov (United States)

    Alvarado, S.; Marín, E.; Juárez, A. G.; Calderón, A.; Ivanov, R.

    2012-07-01

    The implementation of an automated system based on the hot-wire technique is described for the measurement of the thermal conductivity of liquids using equipment easily available in modern physics laboratories at high schools and universities (basically a precision current source and a voltage meter, a data acquisition card, a personal computer and a high purity platinum wire). The wire, which is immersed in the investigated sample, is heated by passing a constant electrical current through it, and its temperature evolution, ΔT, is measured as a function of time, t, for several values of the current. A straightforward methodology is then used for data processing in order to obtain the liquid thermal conductivity. The start point is the well known linear relationship between ΔT and ln(t) predicted for long heating times by a model based on a solution of the heat conduction equation for an infinite lineal heat source embedded in an infinite medium into which heat is conducted without convective and radiative heat losses. A criterion is used to verify that the selected linear region is the one that matches the conditions imposed by the theoretical model. As a consequence the method involves least-squares fits in linear, semi-logarithmic (semi-log) and log-log graphs, so that it becomes attractive not only to teach about heat transfer and thermal properties measurement techniques, but also as a good exercise for students of undergraduate courses of physics and engineering learning about these kinds of mathematical functional relationships between variables. The functionality of the experiment was demonstrated by measuring the thermal conductivity in samples of liquids with well known thermal properties.

  5. Measurement Method of Magnetic Field for the Wire Suspended Micro-Pendulum Accelerometer

    Directory of Open Access Journals (Sweden)

    Yongle Lu

    2015-04-01

    Full Text Available Force producer is one of the core components of a Wire Suspended Micro-Pendulum Accelerometer; and the stability of permanent magnet in the force producer determines the consistency of the acceleration sensor’s scale factor. For an assembled accelerometer; direct measurement of magnetic field strength is not a feasible option; as the magnetometer probe cannot be laid inside the micro-space of the sensor. This paper proposed an indirect measurement method of the remnant magnetization of Micro-Pendulum Accelerometer. The measurement is based on the working principle of the accelerometer; using the current output at several different scenarios to resolve the remnant magnetization of the permanent magnet. Iterative Least Squares algorithm was used for the adjustment of the data due to nonlinearity of this problem. The calculated remnant magnetization was 1.035 T. Compared to the true value; the error was less than 0.001 T. The proposed method provides an effective theoretical guidance for measuring the magnetic field of the Wire Suspended Micro-Pendulum Accelerometer; correcting the scale factor and temperature influence coefficients; etc.

  6. Coaxial airblast atomizers

    Science.gov (United States)

    Hardalupas, Y.; Whitelaw, J. H.

    1993-01-01

    An experimental investigation was performed to quantify the characteristics of the sprays of coaxial injectors with particular emphasis on those aspects relevant to the performance of rocket engines. Measurements for coaxial air blast atomizers were obtained using air to represent the gaseous stream and water to represent the liquid stream. A wide range of flow conditions were examined for sprays with and without swirl for gaseous streams. The parameters varied include Weber number, gas flow rate, liquid flow rate, swirl, and nozzle geometry. Measurements were made with a phase Doppler velocimeter. Major conclusions of the study focused upon droplet size as a function of Weber number, effect of gas flow rate on atomization and spray spread, effect of nozzle geometry on atomization and spread, effect of swirl on atomization, spread, jet recirculation and breakup, and secondary atomization.

  7. Metallic Coaxial Nanolasers

    CERN Document Server

    Hayenga, William E; Hodaei, Hossein; Fainman, 1 Yeshaiahu; Khajavikhan, Mercedeh

    2016-01-01

    The last two decades have witnessed tremendous advancements in the area of nanophotonics and plasmonics. Undoubtedly, the introduction of metallic structures has opened a path towards light con?nement and manipulation at the subwavelength scale { a regime that was previously thought to be out of reach in optics. Of central importance is to devise e?cient light sources to power up the future nanoscale optical circuits. Coaxial resonators can provide a platform to implement such subwavelength sources. They support ultrasmall cavity modes and o?er large mode-emitter overlap as well as multifold scalability. Given their large modulation bandwidth, they hold promise for high speed optical interconnects { where they can be used for light generation and modulation simultaneously. In addition, the possibility of thresholdless operation in such devices may have implications in developing the next generation of e?cient lighting systems. In this review article, the physics and applications of coaxial nanolasers will be ...

  8. Instabilities in Coaxial Rotating Jets

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The aim of this study is the characterization of the cylindrical mixing layer resulting layer resulting from the interaction of two coaxial swirling jets.The experimental part of this study was performed in a cylindrical water tunnel,permitting an independent rotation of two coaxial jets.The rotations are generated by means of 2×36 blades localized in two swirling chambers.As expected,the evolution of the main instabiltiy modes presents certain differences compared to the plane-mixing-layer case ,Experimental results obtained by tomography showed the existence of vortex rings and streamwise vortex paris in the near field region.This method also permitted the observation of the evolution and interaction of different modes.PIV velocity measurements realized in the meridian plans and the plans perpendicular to the jet axis show that rotation distrots the typical top-hat axial velocity profile.The transition of the the axial velocity profile from jet-like into wake-like is also observed.

  9. Variation of Charge Distribution and Capacitance on Thin Wire Using the Method of Moments

    Directory of Open Access Journals (Sweden)

    Mohamed Louzazni

    2013-09-01

    Full Text Available In this paper, we attempting to determine the linear charge density and capacitance on a finite straight segment of thin charged conducting wire of length L=1 m and radius r. we assume that the charge density piecewise constant over the length and the electric potential are is one volt. If the radius are very small compared to the length r<wire in N=100 sub segments, each of length. We choose N points of observation on the surface and the charge density are piecewise constant onto each segment. The integral equation will be transformed to linear equation in N equation with N unknown system. We use the method of moments for solving this system and we obtained a Toeplitz matrix, the results shows the charge density for N=100 is represented on the low levels of discretisation, and the decreasing of the radius increaser the fidelity of the results.

  10. Damage detection methods on wind turbine blade testing with wired and wireless accelerometer sensors

    DEFF Research Database (Denmark)

    Mollineaux, Mark; Balafas, Konstantinos; Branner, Kim;

    2014-01-01

     compare the data collected from the wireless sensors against wired sensors to demonstrate their performance. We explore methods for determining damage. We first explore results of autoregressive coefficients for indicating damage levels. Finally, we demonstrate the use of damage sensitive features from the wavelet transforms of input and output signals to provide a method suitable for non­stationary blade excitations. ...

  11. Investigation of lateral-directional aerodynamic parameters identification method for fly-by-wire passenger airliners

    Institute of Scientific and Technical Information of China (English)

    Wu Zhao; Wang Lixin; Lin Jiaming; Ai Junqiang

    2014-01-01

    A new identification method is proposed to solve the problem of the influence on the loaded excitation signals brought by high feedback gain augmentation in lateral-directional aerody-namic parameters identification of fly-by-wire (FBW) passenger airliners. Taking for example an FBW passenger airliner model with directional relaxed-static-stability, through analysis of its signal energy distribution and airframe frequency response, a new method is proposed for signal type selec-tion, signal parameters design, and the appropriate frequency relationship between the aileron and rudder excitation signals. A simulation validation is presented of the FBW passenger airliner’s lat-eral-directional aerodynamic parameters identification. The validation result demonstrates that the designed signal can excite the lateral-directional motion mode of the FBW passenger airliner ade-quately and persistently. Meanwhile, the relative errors of aerodynamic parameters are less than 5%.

  12. Computer aided design of reentrant coaxial filters including coaxial excitation

    NARCIS (Netherlands)

    Boria, V.; Gerini, G.; Guglielmi, M.

    1999-01-01

    An advanced EM based CAD tool is used for the detailed characterisation of a family of reentrant coaxial waveguide filters. The EM analysis includes the effects of tuning screws and of the input/output coaxial excitation. The software is essentially used as an efficient replacement for the tradition

  13. Wire bonding in microelectronics

    CERN Document Server

    Harman, George G

    2010-01-01

    Wire Bonding in Microelectronics, Third Edition, has been thoroughly revised to help you meet the challenges of today's small-scale and fine-pitch microelectronics. This authoritative guide covers every aspect of designing, manufacturing, and evaluating wire bonds engineered with cutting-edge techniques. In addition to gaining a full grasp of bonding technology, you'll learn how to create reliable bonds at exceedingly high yields, test wire bonds, solve common bonding problems, implement molecular cleaning methods, and much more. Coverage includes: Ultrasonic bonding systems and technologies, including high-frequency systems Bonding wire metallurgy and characteristics, including copper wire Wire bond testing Gold-aluminum intermetallic compounds and other interface reactions Gold and nickel-based bond pad plating materials and problems Cleaning to improve bondability and reliability Mechanical problems in wire bonding High-yield, fine-pitch, specialized-looping, soft-substrate, and extreme-temperature wire bo...

  14. Thermal Control Method for High-Current Wire Bundles by Injecting a Thermally Conductive Filler

    Science.gov (United States)

    Rodriguez-Ruiz, Juan; Rowles, Russell; Greer, Greg

    2011-01-01

    A procedure was developed to inject thermal filler material (a paste-like substance) inside the power wire bundle coming from solar arrays. This substance fills in voids between wires, which enhances the heat path and reduces wire temperature. This leads to a reduced amount of heat generated. This technique is especially helpful for current and future generation high-power spacecraft (1 kW or more), because the heat generated by the power wires is significant enough to cause unacceptable overheating to critical components that are in close contact with the bundle.

  15. A controller design method for 3 phase 4 wire grid connected VSI with LCL filter

    Indian Academy of Sciences (India)

    Anirban Ghoshal; Vinod John

    2015-08-01

    Closed loop control of a grid connected VSI requires line current control and dc bus voltage control. The closed loop system comprising PR current controller and grid connected VSI with LCL filter is a higher order system. Closed loop control gain expressions are therefore difficult to obtain directly for such systems. In this work a simplified approach has been adopted to find current and voltage controller gain expressions for a 3 phase 4 wire grid connected VSI with LCL filter. The closed loop system considered here utilises PR current controller in natural reference frame and PI controller for dc bus voltage control. Asymptotic frequency response plot and gain bandwidth requirements of the system have been used for current control and voltage controller design. A simplified lower order model, derived for closed loop current control, is used for the dc bus voltage controller design. The adopted design method has been verified through experiments by comparison of the time domain response.

  16. Measurement of the Thermal-Conductivity Coefficient of Nanofluids by the Hot-Wire Method

    Science.gov (United States)

    Minakov, A. V.; Rudyak, V. Ya.; Guzei, D. V.; Pryazhnikov, M. I.; Lobasov, A. S.

    2015-01-01

    In this work, the authors present results of adaptation and testing of the hot-wire method for determination for the thermal-conductivity coefficient of nanofluids. A mathematical model of heat transfer with allowance for free convection has been constructed to elucidate the parameters of an experimental setup and the range of its applicability. The experimental procedure has been tested on measurements of the thermal conductivities of water and ethylene glycol. The thermal-conductivity coefficient of a nanofluid has been measured at room temperature. The nanofluid under study was prepared on the basis of ethylene glycol and alumina nanoparticles. The concentrations of the nanoparticles ranged from 0.5% to 2% by volume. Good agreement has been obtained between the measured values of the thermal-conductivity coefficient and the data of other authors.

  17. Study of the flow characteristics of supersonic coaxial jets

    Energy Technology Data Exchange (ETDEWEB)

    Lee, K.H. [Andong National University, Andong (Korea); Koo, B.S. [Andong National University Graudate School, Andong (Korea)

    2001-12-01

    Supersonic coaxial jets are investigated numerically by using the axisymmetric, Navier-Stokes equations which are solved using a fully implicit finite volume method. Three different kinds of coaxial nozzles are employed to understand the flow physics involved in the supersonic coaxial jets. Two convergent-divergent supersonic nozzles are designed to have the same Mach number 2.0, and used to compare the coaxial jet flows with those discharging from one constant-area nozzle. The impingement angle of the annular jets are varied. The primary pressure ratio is changed in the range from 2.0 to 10.0 and the assistant jet ratio from 1.0 to 3.0. The results obtained show that the fluctuations of the total pressure and Mach number along the jet axis are much higher in the constant-area nozzle than those in the convergent-divergent nozzles, and the constant-area nozzle lead to higher total pressure losses, compared with the convergent-divergent nozzles. The assistant jets from the annular nozzle affect the coaxial jet flows within the distance less than about ten times the nozzle throat diameter, but beyond it the coaxial jet is conical with self-similar velocity profiles. Increasing both the primary jet pressure ratio and the assistant jet pressure ratio produces a longer coaxial jet core. (author). 14 refs., 9 figs.

  18. Fabrication and characterization of iron pnictide wires and bulk materials through the powder-in-tube method

    Energy Technology Data Exchange (ETDEWEB)

    Ma Yanwei, E-mail: ywma@mail.iee.ac.c [Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering, Chinese Academy of Sciences, P.O. Box 2703, Beijing 100190 (China); Gao Zhaoshun; Qi Yanpeng; Zhang Xianping; Wang Lei; Zhang Zhiyu; Wang Dongliang [Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering, Chinese Academy of Sciences, P.O. Box 2703, Beijing 100190 (China)

    2009-05-01

    The recent discovery of superconductivity in the iron-based superconductors with very high upper critical fields presents a new possibility for practical applications, but fabricating fine-wire is a challenge because of mechanically hard and brittle powders and the toxicity and volatility of arsenic. In this paper, we report the synthesis and the physical characterization of iron pnictide wires and bulks prepared by the powder-in-tube method (PIT). A new class of high-T{sub c} iron pnictide composite wires, such as LaFeAsO{sub 1-x}F{sub x}, SmFeAsO{sub 1-x}F{sub x} and Sr{sub 1-x}K{sub x}FeAs, has been fabricated by the in situ PIT technique using Fe, Ta and Nb tubes. Microscopy and X-ray analysis show that the superconducting core is continuous, and retains phase composition after wire drawing and heat treatment. Furthermore, the wires exhibit a very weak J{sub c}-field dependence behavior even at high temperatures. The upper critical field H{sub c2}(0) value can exceed 100 T, surpassing those of MgB{sub 2} and all the low temperature superconductors and indicating a strong potential for applications requiring very high field. These results demonstrate the feasibility of producing superconducting pnictide composite wire. We also applied the one-step PIT method to synthesize the iron-based bulks, due to its convenience and safety. In fact, by using this technique, we have successfully discovered superconductivity at 35 K and 15 K in Eu{sub 0.7}Na{sub 0.3}Fe{sub 2}As{sub 2} and SmCoFeAsO compounds, respectively. These clearly suggest that the one-step PIT technique is unique and versatile and hence can be tailored easily for other rare earth derivatives of novel iron-based superconductors.

  19. Development of the extension method of overhead power transmission wires utilizing radio controlled, small-sized airships

    Energy Technology Data Exchange (ETDEWEB)

    Tanimoto, Nariyuki

    1988-11-01

    Chubu Electric Power's Yokkaichi Electric Power Bureau has, with the cooperation of Taiheiyo Kogyo Co., Ltd. in Ogaki City, developed a radio-controlled, small-sized airship to fly across the particular spans (rivers, valleys, residential areas) for the installation of power transmission wires. This small-sized airship doesn't require a runway, neither does it cause danger to the workers because it does not have such large rotary wings as a radio-controlled helicopter. The ship's body length is 7.7m. Its weight is 28kg, and its carrying capacity is 3kg. It is possible for several operators to fly the ship in relays by radio control. At the starting point, a gondola is attached to the ship body. The gondola is equipped with a guide rope of 1.8mm diameter. After an electric mechanic has hooked an electric wire to the guide rope at the top of the starting steel tower, the airship flies across the span to the next steel tower, and thus extends the electric wire. At the terminal steel tower, an electric mechanic receives the wire, separates the gondola from the airship, and then the airship lands. Depending on the occasions, it is possible to station operators on the way and assure the flight. At present the span length limit is 700m. This method was experimentally carried out for the wire extension of 688m span across the Suzuka River, and for the wire extension of continuous spans in the Kawai branch line installation work. Thus the method was successfully put to practical use. 4 figures, 1 table.

  20. Fabrication and characterization of iron pnictide wires and bulk materials through the powder-in-tube method

    Science.gov (United States)

    Ma, Yanwei; Gao, Zhaoshun; Qi, Yanpeng; Zhang, Xianping; Wang, Lei; Zhang, Zhiyu; Wang, Dongliang

    2009-05-01

    The recent discovery of superconductivity in the iron-based superconductors with very high upper critical fields presents a new possibility for practical applications, but fabricating fine-wire is a challenge because of mechanically hard and brittle powders and the toxicity and volatility of arsenic. In this paper, we report the synthesis and the physical characterization of iron pnictide wires and bulks prepared by the powder-in-tube method (PIT). A new class of high- Tc iron pnictide composite wires, such as LaFeAsO 1-xF x, SmFeAsO 1-xF x and Sr 1-xK xFeAs, has been fabricated by the in situ PIT technique using Fe, Ta and Nb tubes. Microscopy and X-ray analysis show that the superconducting core is continuous, and retains phase composition after wire drawing and heat treatment. Furthermore, the wires exhibit a very weak Jc-field dependence behavior even at high temperatures. The upper critical field Hc2(0) value can exceed 100 T, surpassing those of MgB 2 and all the low temperature superconductors and indicating a strong potential for applications requiring very high field. These results demonstrate the feasibility of producing superconducting pnictide composite wire. We also applied the one-step PIT method to synthesize the iron-based bulks, due to its convenience and safety. In fact, by using this technique, we have successfully discovered superconductivity at 35 K and 15 K in Eu 0.7Na 0.3Fe 2As 2 and SmCoFeAsO compounds, respectively. These clearly suggest that the one-step PIT technique is unique and versatile and hence can be tailored easily for other rare earth derivatives of novel iron-based superconductors.

  1. THE METHODS OF CALCULATIONS OF THE TEMPERATURE BREAKDOWN FIELD IN THE LINE OF THE MODEM HIGH-SPEED WIRE MILL

    Directory of Open Access Journals (Sweden)

    S. M. Zhuchkov

    2007-01-01

    Full Text Available The calculation methods of the temperature field of the breakdown, being rolled in lines of the modern high-speed wire mill, is developed on the basis of solving of problem of the contact exchange of hot metal with cold rollers.

  2. Fatigue life prediction method for contact wire using maximum local stress

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yong Seok; Haochuang, Li; Seok, Chang Sung; Koo, Jae Mean [Sungkyunkwan University, Suwon (Korea, Republic of); Lee, Ki Won; Kwon, Sam Young; Cho, Yong Hyeon [Korea Railroad Research Institute, Uiwang (Korea, Republic of)

    2015-01-15

    Railway contact wires supplying electricity to trains are exposed to repeated mechanical strain and stress caused by their own weight and discontinuous contact with a pantograph during train operation. Since the speed of railway transportation has increased continuously, railway industries have recently reported a number of contact wire failures caused by mechanical fatigue fractures instead of normal wear, which has been a more common failure mechanism. To secure the safety and durability of contact wires in environments with increased train speeds, a bending fatigue test on contact wire has been performed. The test equipment is too complicated to evaluate the fatigue characteristics of contact wire. Thus, the axial tension fatigue test was performed for a standard specimen, and the bending fatigue life for the contact wire structure was then predicted using the maximum local stress occurring at the top of the contact wire. Lastly, the tested bending fatigue life of the structure was compared with the fatigue life predicted by the axial tension fatigue test for verification.

  3. Optimal forming zone length in continuous extrusion of lead-clad glass fiber wire

    Institute of Scientific and Technical Information of China (English)

    李霞; 唐景林; 王丽薇; 高明

    2008-01-01

    Forming zone length (FZL) is a key parameter of the lead-clad glass fiber extrusion dies, and an unsuitable FZL will lead to breakage of the glass fiber and/or unacceptable geometric and metallographic qualities of the product. The optimal FZL was determined theoretically based on a mathematical model established by upper bound method, and accepted Pb-GF wire was actually obtained experimentally by symmetric side-feed extrusion at a much lower temperature than that published before. The wire has features of fine grains, uniform diameter, good coaxiality and satisfied mechanical property. The results and conclusions obtained in the research can be used to design the forming tools for lead-clad glass fiber extrusion and have significance to further research on the extrusion of other complex wires of metal-clad brittle core.

  4. Vibrating wire alignment technique

    CERN Document Server

    Xiao-Long, Wang; lei, Wu; Chun-Hua, Li

    2013-01-01

    Vibrating wire alignment technique is a kind of method which through measuring the spatial distribution of magnetic field to do the alignment and it can achieve very high alignment accuracy. Vibrating wire alignment technique can be applied for magnet fiducialization and accelerator straight section components alignment, it is a necessary supplement for conventional alignment method. This article will systematically expound the international research achievements of vibrating wire alignment technique, including vibrating wire model analysis, system frequency calculation, wire sag calculation and the relation between wire amplitude and magnetic induction intensity. On the basis of model analysis this article will introduce the alignment method which based on magnetic field measurement and the alignment method which based on amplitude and phase measurement. Finally, some basic questions will be discussed and the solutions will be given.

  5. Coaxial Atomic Force Microscope Tweezers

    CERN Document Server

    Brown, K A; Westervelt, R M

    2010-01-01

    We demonstrate coaxial atomic force microscope (AFM) tweezers that can trap and place small objects using dielectrophoresis (DEP). An attractive force is generated at the tip of a coaxial AFM probe by applying a radio frequency voltage between the center conductor and a grounded shield; the origin of the force is found to be DEP by measuring the pull-off force vs. applied voltage. We show that the coaxial AFM tweezers (CAT) can perform three dimensional assembly by picking up a specified silica microsphere, imaging with the microsphere at the end of the tip, and placing it at a target destination.

  6. Cryogenic coaxial microwave filters

    CERN Document Server

    Tancredi, G; Meeson, P J

    2014-01-01

    At millikelvin temperatures the careful filtering of electromagnetic radiation, especially in the microwave regime, is critical for controlling the electromagnetic environment for experiments in fields such as solid-state quantum information processing and quantum metrology. We present a design for a filter consisting of small diameter dissipative coaxial cables that is straightforward to construct and provides a quantitatively predictable attenuation spectrum. We describe the fabrication process and demonstrate that the performance of the filters is in good agreement with theoretical modelling. We further perform an indicative test of the performance of the filters by making current-voltage measurements of small, underdamped Josephson Junctions at 15 mK and we present the results.

  7. Assessment of the hardness of different orthodontic wires and brackets produced by metal injection molding and conventional methods.

    Science.gov (United States)

    Alavi, Shiva; Kachuie, Marzie

    2017-01-01

    This study was conducted to assess the hardness of orthodontic brackets produced by metal injection molding (MIM) and conventional methods and different orthodontic wires (stainless steel, nickel-titanium [Ni-Ti], and beta-titanium alloys) for better clinical results. A total of 15 specimens from each brand of orthodontic brackets and wires were examined. The brackets (Elite Opti-Mim which is produced by MIM process and Ultratrimm which is produced by conventional brazing method) and the wires (stainless steel, Ni-Ti, and beta-titanium) were embedded in epoxy resin, followed by grinding, polishing, and coating. Then, X-ray energy dispersive spectroscopy (EDS) microanalysis was applied to assess their elemental composition. The same specimen surfaces were repolished and used for Vickers microhardness assessment. Hardness was statistically analyzed with Kruskal-Wallis test, followed by Mann-Whitney test at the 0.05 level of significance. The X-ray EDS analysis revealed different ferrous or co-based alloys in each bracket. The maximum mean hardness values of the wires were achieved for stainless steel (SS) (529.85 Vickers hardness [VHN]) versus the minimum values for beta-titanium (334.65 VHN). Among the brackets, Elite Opti-Mim exhibited significantly higher VHN values (262.66 VHN) compared to Ultratrimm (206.59 VHN). VHN values of wire alloys were significantly higher than those of the brackets. MIM orthodontic brackets exhibited hardness values much lower than those of SS orthodontic archwires and were more compatible with NiTi and beta-titanium archwires. A wide range of microhardness values has been reported for conventional orthodontic brackets and it should be considered that the manufacturing method might be only one of the factors affecting the mechanical properties of orthodontic brackets including hardness.

  8. 盘条焊接操作方法的改进%Improvement of wire rod welding operation method

    Institute of Scientific and Technical Information of China (English)

    王鸿利; 毛爱菊

    2013-01-01

    High carbon steel wire broken occurs easily in process of wire drawing,wire rod welding operation new method was summarized by testing.(1) prepare the end,to cut the burr of the end with grinding machine,and done 45°chamfering treatment of length 2 mm,(2) welding,to choose different current according to the size and specification of welding material in condition of same materials,to ensure proper welding temperature,(3) to remove welding joint,air cooling to under 80 ℃ at room temperature,the welding joint diameter after polishing is no less than 95% of wire rod diameter.The four step operation method of welding tempering is given.To adopt new welding method improves wire rod welding quality,area reduction of wire rod is 10% ~20%,tensile strength reaches 85% ~95% of that of base material,the broken time each 100 ton of wire drawing decreases from original 2.50 times to 1.16 times.%高碳钢丝拉拔过程容易产生断丝,通过试验总结出盘条焊接操作新方法.(1)端头准备:用砂轮机将切头处毛刺去除干净,并进行长度为2mm的45°倒角处理;(2)对焊:在材质相同的条件下依据被焊接材料的尺寸、规格选择不同的电流,以保证合适的焊接温度;(3)焊缝隆起清除:在环境温度下自然冷却至80℃以下,焊缝处打磨后的直径应不小于盘条原始直径的95%.给出焊接回火的4步操作法.采用新的焊接方法,提高了盘条焊接质量,盘条的断面收缩率在10%~20%,抗拉强度达到母材抗拉强度的85% ~95%,拉丝的断头次数由原来的每百吨2.50次下降到1.16次.

  9. Investigation of longitudinal aerodynamic parameters identification method for fly-by-wire passenger airliners

    Institute of Scientific and Technical Information of China (English)

    Wu Zhao; Wang Lixin; Xu Zijian; Tan Xiangsheng

    2013-01-01

    The flight control system of a fly-by-wire (FBW) passenger airliner with a complex frame-work and high feedback gain augmentation would change the original characteristic of a loaded sig-nal and suppress the excitation of an airplane’s pertinent motion modes. Taking a research example of an FBW passenger airliner model with longitudinal relaxed-static-stability, a new method of signal type selection and signal parameter design is proposed, through analysis of signal energy distribution and plane body’s frequency response. According to CCAR60--the Appraisal and Use Regulation of Flight Simulator Device, the simulation validation of the FBW passenger airliner’s longitudinal aerodynamic parameters identification is put forward. The validation result indicates that the designed signal could excite the longitudinal motion mode of the FBW passenger airliner adequately and the multiparameter comparison in simulation meets the objective test request of CCAR60. Meanwhile, the relative errors of aerodynamic parameters are less than 10%.

  10. Hydrogenated Nanocrystalline Silicon Thin Films Prepared by Hot-Wire Method with Varied Process Pressure

    Directory of Open Access Journals (Sweden)

    V. S. Waman

    2011-01-01

    Full Text Available Hydrogenated nanocrystalline silicon films were prepared by hot-wire method at low substrate temperature (200∘C without hydrogen dilution of silane (SiH4. A variety of techniques, including Raman spectroscopy, low angle X-ray diffraction (XRD, Fourier transform infrared (FTIR spectroscopy, atomic force microscopy (AFM, and UV-visible (UV-Vis spectroscopy, were used to characterize these films for structural and optical properties. Films are grown at reasonably high deposition rates (>15 Å/s, which are very much appreciated for the fabrication of cost effective devices. Different crystalline fractions (from 2.5% to 63% and crystallite size (3.6–6.0 nm can be achieved by controlling the process pressure. It is observed that with increase in process pressure, the hydrogen bonding in the films shifts from Si–H to Si–H2 and (Si–H2n complexes. The band gaps of the films are found in the range 1.83–2.11 eV, whereas the hydrogen content remains <9 at.% over the entire range of process pressure studied. The ease of depositing films with tunable band gap is useful for fabrication of tandem solar cells. A correlation between structural and optical properties has been found and discussed in detail.

  11. Disintegration process and performance of a coaxial porous injector

    Science.gov (United States)

    Lee, Keonwoong; Kim, Dohun; Koo, Jaye

    2016-10-01

    In order to understand the breakup performance of coaxial porous injectors, the sprays of coaxial porous injectors with two different porous material cylinder lengths were compared with those of conventional shear coaxial injectors. To allow comparison, the wall injection lengths were designed to be equivalent to the value of the recess depth. Cold flow sprays were visualized using back-lit photography methods and analyzed quantitatively with a laser diffraction apparatus, in order to study the effects of the momentum flux ratio and Weber number on the breakup for each type of injector. In case of the shear coaxial injector, the large liquid core was observed in low air mass flow rate condition. However, the destabilization of the liquid jet from the coaxial porous injector is almost complete within the inner region, near the injector face plate. Additionally, better breakup performance in low gas flow rate condition was obtained when the porous cylinder length decreased, while the shear coaxial injectors showed better breakup efficiency when the recess length increased. In conclusion, the different breakup process caused by the radial momentum in the inner region of the porous injector disintegrated the liquid core.

  12. Wire + Arc Additive Manufacturing

    OpenAIRE

    Williams, Stewart W.; Martina, Filomeno; Addison, Adrian C.; Ding, Jialuo; Pardal, Goncalo; Colegrove, Paul A.

    2016-01-01

    Depositing large components (>10 kg) in titanium, aluminium, steel and other metals is possible using Wire + Arc Additive Manufacturing. This technology adopts arc welding tools and wire as feedstock for additive manufacturing purposes. High deposition rates, low material and equipment costs, and good structural integrity make Wire+Arc Additive Manufacturing a suitable candidate for replacing the current method of manufacturing from solid billets or large forgings, especially with regards to ...

  13. Charged particle tracking through electrostatic wire meshes using the finite element method

    Science.gov (United States)

    Devlin, L. J.; Karamyshev, O.; Welsch, C. P.

    2016-06-01

    Wire meshes are used across many disciplines to accelerate and focus charged particles, however, analytical solutions are non-exact and few codes exist which simulate the exact fields around a mesh with physical sizes. A tracking code based in Matlab-Simulink using field maps generated using finite element software has been developed which tracks electrons or ions through electrostatic wire meshes. The fields around such a geometry are presented as an analytical expression using several basic assumptions, however, it is apparent that computational calculations are required to obtain realistic values of electric potential and fields, particularly when multiple wire meshes are deployed. The tracking code is flexible in that any quantitatively describable particle distribution can be used for both electrons and ions as well as other benefits such as ease of export to other programs for analysis. The code is made freely available and physical examples are highlighted where this code could be beneficial for different applications.

  14. Charged particle tracking through electrostatic wire meshes using the finite element method

    Energy Technology Data Exchange (ETDEWEB)

    Devlin, L. J.; Karamyshev, O.; Welsch, C. P., E-mail: carsten.welsch@cockcroft.ac.uk [The Cockcroft Institute, Daresbury Laboratory, Warrington (United Kingdom); Department of Physics, University of Liverpool, Liverpool (United Kingdom)

    2016-06-15

    Wire meshes are used across many disciplines to accelerate and focus charged particles, however, analytical solutions are non-exact and few codes exist which simulate the exact fields around a mesh with physical sizes. A tracking code based in Matlab-Simulink using field maps generated using finite element software has been developed which tracks electrons or ions through electrostatic wire meshes. The fields around such a geometry are presented as an analytical expression using several basic assumptions, however, it is apparent that computational calculations are required to obtain realistic values of electric potential and fields, particularly when multiple wire meshes are deployed. The tracking code is flexible in that any quantitatively describable particle distribution can be used for both electrons and ions as well as other benefits such as ease of export to other programs for analysis. The code is made freely available and physical examples are highlighted where this code could be beneficial for different applications.

  15. Using Cored Wires Injection 2PE-9 Method in the Production of Ferritic Si-Mo Ductile Iron Castings

    Directory of Open Access Journals (Sweden)

    E. Guzik

    2012-12-01

    Full Text Available The results of studies on the use of modern two cored wires injection method for production of ferritic nodular cast iron (ductile iron with use of unique implementation of drum ladle as a treatment / transport and casting ladle instead vertical treatment ladle was described. The injection of length of Ø 9mm wires, cored: in FeSi + Mg nodulariser mixture and inoculant master alloy is a treatment method which can be used to produce iron melted in coreless induction furnace. This paper describes the results and analysis of using this method for optimal production of ductile iron under specific industrial conditions. It means, that length of nodulariser wire plus treatment and pouring temperatures were optimized. In this case, was taken ductile iron with material designation: EN-GJS-SiMo40-6 Grade according EN 16124:2010 E. Microstructure of great number of trials was controlled on internally used sample which has been correlated with standardsample before. The paper presents typical ferritic metallic matrix and nodular graphite. Additionally, mechanical properties were checked in some experiments. Mean values of magnesium recovery and cost of this new method from optimized process parameters werecalculated as well.

  16. Estimation of the Level of Residual Stress in Wires with a Magnetic Method

    Directory of Open Access Journals (Sweden)

    Suliga M.

    2015-04-01

    Full Text Available Residual stress present in wires after drawing process affects their magnetic properties. The paper presents a concept to estimate the level of residual stress on the basis of measurements of hysteresis loops. In order to describe the effect qualitatively the Jiles-Atherton-Sablik description is adapted. On the basis of variations in hysteresis loop shapes the average values of residual stress in wires for different single draft values are determined. It was found that the estimated average values by magnetic stresses are comparable with the results of numerical modeling and experimental studies.

  17. 同轴馈电耦合微带贴片天线的时域有限差分法分析%The analysis of a coaxial probe-fed coupled patch antenna using the FDTD method

    Institute of Scientific and Technical Information of China (English)

    许锋; 洪伟; 冯祖伟

    2001-01-01

    提出一种融合曲线坐标和直角坐标的区域网格划分方法。在同轴线区域采用曲线坐标网格,用以代替传统的阶梯剖分,在其它区域及边界上采用直角坐标网格,从而极大地提高了计算效率。同时,在时域有限差分法中还采用了非均匀网格划分、PML吸收边界和Prony外推法等技术,对同轴馈电的耦合微带贴片天线进行了分析。%A method is proposed for the integrated use of conformal gridsand rectangular grids. In the coaxial line region, conformal grids are used instead of the classical staircasing method. In other regions and boundaries, rectangular grids are used. This greatly increased the calculation efficiency. Besides, the FDTD method with nonuniform orthogonal grids, extrapolation techniques and perfectly match layer (PML) are also applied to analyze a coaxial feeding coupled patch antenna.

  18. Method of forming low cost, formable High T(subc) superconducting wire

    Science.gov (United States)

    Smialek, James L. (Inventor)

    1989-01-01

    A ceramic superconductivity part, such as a wire, is produced through the partial oxidation of a specially formulated copper alloy in a core. The alloys contains low level of quantities of rare earth and alkaline earth dopant elements. Upon oxidation at high temperatures, and superconducting oxide phases are formed as a thin film.

  19. Survey of Processing Methods for High Strength High Conductivity Wires for High Field Magnet Applications

    Energy Technology Data Exchange (ETDEWEB)

    Han, K.; Embury, J.D.

    1998-10-01

    This paper will deal with the basic concepts of attaining combination of high strength and high conductivity in pure materials, in-situ composites and macrocomposites. It will survey current attainments, and outline where some future developments may lie in developing wire products that are close to the theoretical strength of future magnet applications.

  20. A Hot-Wire Method Based Thermal Conductivity Measurement Apparatus for Teaching Purposes

    Science.gov (United States)

    Alvarado, S.; Marin, E.; Juarez, A. G.; Calderon, A.; Ivanov, R.

    2012-01-01

    The implementation of an automated system based on the hot-wire technique is described for the measurement of the thermal conductivity of liquids using equipment easily available in modern physics laboratories at high schools and universities (basically a precision current source and a voltage meter, a data acquisition card, a personal computer…

  1. Thermal conductivity measurement in clay dominant consolidated material by Transient Hot-Wire method.

    Science.gov (United States)

    Garnier, J. P.; Gallier, J.; Mercx, B.; Dudoignon, P.; Milcent, D.

    2010-06-01

    The transient hot-wire (THW) technique is widely used for measurements of the thermal-conductivity of most fluids and some attempts have also been carried out for simultaneous measurements of the thermal-diffusivity with the same hot wire. This technique was also tried to determine thermal properties of soils by the mean of probes which can be considered as wire with some assumptions. The purpose of this paper is to validate the thermal conductivity measurement by the THW technique in geomaterials, composed of compacted sand + clay mineral that can be used for earth construction (Compacted Earth Brick). The thermal transfer behaviors are mainly governed by the texture and moisture of the geomaterials. Thus the investigations were performed (1) in media made of glass beads of different diameters in dry and saturated state in order to observe the role of grain sizes and saturation state on the wire temperature (Δt) measurements and (2) in the compacted clay-geomaterial at different moisture states. The Δt / ln(t) diagrams allow the calculation of two thermal conductivities. The first one, measured in the short time acquisition (thermal conductivity of the material.

  2. Thermal conductivity measurement in clay dominant consolidated material by Transient Hot-Wire method.

    Directory of Open Access Journals (Sweden)

    Milcent D.

    2010-06-01

    Full Text Available The transient hot-wire (THW technique is widely used for measurements of the thermal-conductivity of most fluids and some attempts have also been carried out for simultaneous measurements of the thermal-diffusivity with the same hot wire. This technique was also tried to determine thermal properties of soils by the mean of probes which can be considered as wire with some assumptions. The purpose of this paper is to validate the thermal conductivity measurement by the THW technique in geomaterials, composed of compacted sand + clay mineral that can be used for earth construction (Compacted Earth Brick. The thermal transfer behaviors are mainly governed by the texture and moisture of the geomaterials. Thus the investigations were performed (1 in media made of glass beads of different diameters in dry and saturated state in order to observe the role of grain sizes and saturation state on the wire temperature (Δt measurements and (2 in the compacted clay-geomaterial at different moisture states. The Δt / ln(t diagrams allow the calculation of two thermal conductivities. The first one, measured in the short time acquisition (< 1s, characterizes the microtexture of the material and its hydrated state. The second one, measured for longer time acquisitions, characterizes the mean thermal conductivity of the material.

  3. 29 CFR 1910.305 - Wiring methods, components, and equipment for general use.

    Science.gov (United States)

    2010-07-01

    ... STOO, except for the wiring of chain-supported lighting fixtures and supply cords for portable lamps... electrical noise (electromagnetic interference) of the grounding circuit, an equipment enclosure supplied by a branch circuit may be isolated from a raceway containing circuits supplying only that equipment...

  4. A Comparison of Zero Mean Strain Rotating Beam Fatigue Test Methods for Nitinol Wire

    Science.gov (United States)

    Norwich, Dennis W.

    2014-07-01

    Zero mean strain rotating beam fatigue testing has become the standard for comparing the fatigue properties of Nitinol wire. Most commercially available equipment consists of either a two-chuck or a chuck and bushing system, where the wire length and center-to-center axis distance determine the maximum strain on the wire. For the two-chuck system, the samples are constrained at either end of the wire, and both chucks are driven at the same speed. For the chuck and bushing system, the sample is constrained at one end in a chuck and rides freely in a bushing at the other end. These equivalent systems will both be herein referred to as Chuck-to-Chuck systems. An alternate system uses a machined test block with a specific radius to guide the wire at a known strain during testing. In either system, the test parts can be immersed in a temperature-controlled fluid bath to eliminate any heating effect created in the specimen due to dissipative processes during cyclic loading (cyclic stress induced the formation of martensite) Wagner et al. ( Mater. Sci. Eng. A, 378, p 105-109, 1). This study will compare the results of the same starting material tested with each system to determine if the test system differences affect the final results. The advantages and disadvantages of each system will be highlighted and compared. The factors compared will include ease of setup, operator skill level required, consistency of strain measurement, equipment test limits, and data recovery and analysis. Also, the effect of test speed on the test results for each system will be investigated.

  5. Thermal Conductivity Measurement of Semitransparent Media at Temperatures from 300 to 800 K by Hot—Wire Method

    Institute of Scientific and Technical Information of China (English)

    XinxinZhang; FanYu; 等

    1996-01-01

    In this paper,a new measurment technique for determining thermal conductivity of semitransparent media in the temperature range 300-800 K is reported.The experimental setup is based on the step power forced transient hot wire technique It is assumed that the radiative contribution to the heat transfer process arises from emission,Not from absorption.In this case,application of the "thermal quadruples" method allows a very simple construction of analytical models of the experimental setup.The parameter sensityvity analysis demonstrates that the thermal conductivity of semitransparent meidia can be determined from the hot wire temperature response,The experimental results of a kind of glass between 300 and 800 K are presented.

  6. A new method to catheterize a femoral artery in mice using a nylon suture as a 'guide wire'.

    Science.gov (United States)

    Fukui, S; Nawshiro, H; Wada, K; Shima, K; Hallenbeck, J M

    2001-09-01

    Mice are commonly used in laboratory experiments. Their femoral arteries are so tiny that catheterization is quite difficult. We describe a new method to catheterize the femoral artery in mice. The key feature of this new method is the use of a nylon suture as a 'guide wire'. The full catheterization system consists of two sizes of polyethylene tubes (PE-10, PE-50) and a 4-0 nylon suture. We have been able to repeatedly catheterize mouse femoral arteries (n = 57) successfully and easily with this new system. We believe that this new method can facilitate vascular catheterization in small animals such as mice.

  7. Computational Study of Flow Interactions in Coaxial Rotors

    Science.gov (United States)

    Yoon, Seokkwan; Lee, Henry C.; Pulliam, Thomas H.

    2016-01-01

    account for multiple real-world constraints up front in design nor possible to know what performance is possible with a given design. Since unmanned vehicles are sized and optimized for the particular mission, a modern low-fidelity conceptual design and sizing tool that has been used for the design of large helicopters can be used for design of small coaxial rotorcraft. However, unlike most helicopters with single main rotor, the interactions between the upper and lower rotors emerge as an important factor to consider in design because an increase in performance of a multi-rotor system is not proportional to the number of rotors. Interference losses and differences in thrusts between the upper and lower rotors were investigated by theoretical methods as well as a computational fluid dynamics (CFD) method using the Reynolds-Averaged Navier-Stokes (RANS) equations. In this work, hybrid turbulence models are used to investigate the physics of interactions between coaxial rotors and a fuselage that are not well understood. Present study covers not only small-scale drones but also large-scale coaxial rotors for heavy-lifting missions. Considering the recently proposed FAA drone rules that require the flight only in visual line-of-sight, a large multirotor might be used as an airborne carrier for launch and recovery of unmanned aircraft systems with a human operator onboard. For applications to civil operations, their aerodynamic performance and noise levels need to be assessed. Noise is one of the largest limiting factors to rotorcraft operations in urban area. Since the high-frequency noise of multi-rotors may increase the annoyance, noise may turn out to be a key issue that must be addressed for market acceptability. One of the objectives of the present work is to study the effects of inter-rotor spacing and collectives on the performance, efficiency, and acoustics of coaxial rotor systems.

  8. Wire Chamber

    CERN Multimedia

    Magnetoscriptive readout wire chamber. Multi-wire detectors contain layers of positively and negatively charged wires enclosed in a chamber full of gas. A charged particle passing through the chamber knocks negatively charged electrons out of atoms in the gas, leaving behind positive ions. The electrons are pulled towards the positively charged wires. They collide with other atoms on the way, producing an avalanche of electrons and ions. The movement of these electrons and ions induces an electric pulse in the wires which is collected by fast electronics. The size of the pulse is proportional to the energy loss of the original particle.

  9. wire chamber

    CERN Multimedia

    1967-01-01

    Magnetoscriptive readout wire chamber.Multi-wire detectors contain layers of positively and negatively charged wires enclosed in a chamber full of gas. A charged particle passing through the chamber knocks negatively charged electrons out of atoms in the gas, leaving behind positive ions. The electrons are pulled towards the positively charged wires. They collide with other atoms on the way, producing an avalanche of electrons and ions. The movement of these electrons and ions induces an electric pulse in the wires which is collected by fast electronics. The size of the pulse is proportional to the energy loss of the original particle.

  10. wire chamber

    CERN Multimedia

    Proportional multi-wire chamber. Multi-wire detectors contain layers of positively and negatively charged wires enclosed in a chamber full of gas. A charged particle passing through the chamber knocks negatively charged electrons out of atoms in the gas, leaving behind positive ions. The electrons are pulled towards the positively charged wires. They collide with other atoms on the way, producing an avalanche of electrons and ions. The movement of these electrons and ions induces an electric pulse in the wires which is collected by fast electronics. The size of the pulse is proportional to the energy loss of the original particle. Proportional wire chambers allow a much quicker reading than the optical or magnetoscriptive readout wire chambers.

  11. Electron microscopy observations of MgB 2 wire prepared by an internal Mg diffusion method

    Science.gov (United States)

    Shimada, Y.; Kubota, Y.; Hata, S.; Ikeda, K.; Nakashima, H.; Matsumoto, A.; Togano, K.; Kumakura, H.

    2011-11-01

    Microstructure in a high-density MgB2 wire fabricated by an internal Mg diffusion (IMD) process has been investigated by electron microscopy imaging and analysis at different scales. In the IMD process, a pure Mg rod was used as Mg source, and nanosized SiC powders were mixed with amorphous B powders. In the case of a heat treatment at 640 °C for 1 h carried out after rolling and drawing processes, the wire has two microstructural features that degrade critical current density: uncrystallized zones composed mainly of unreacted B and SiC powders, and cracks partly filled with course Mg2Si crystals. Those cracks were formed in the uncrystallized zones as well as in crystallized MgB2 zones. It indicate that the cracks formed by the mechanical milling and drawing remain after the heat treatment.

  12. A combination of thermal methods to assess coronary pressure and flow dynamics with a pressure-sensing guide wire.

    Science.gov (United States)

    van der Horst, Arjen; Van't Veer, Marcel; van der Sligte, Robin A M; Rutten, Marcel C M; Pijls, Nico H J; van de Vosse, Frans N

    2013-03-01

    Measurement of coronary pressure and absolute flow dynamics have shown great potential in discerning different types of coronary circulatory disease. In the present study, the feasibility of assessing pressure and flow dynamics with a combination of two thermal methods, developed in combination with a pressure-sensor-tipped guide wire, was evaluated in an in vitro coronary model. A continuous infusion thermodilution method was employed to determine the average flow, whereas a thermal anemometric method was utilized to assess the pressure and flow dynamics, simultaneously. In the latter method, the electrical power supplied to an element, kept at constant temperature above ambient temperature, was used as a measure for the shear rate. It was found that, using a single calibration function, the method was able to assess coronary pressure and flow dynamics for different flow amplitudes, heart rates, and different pressure wires. However, due to the fact that the thermal anemometric method cannot detect local shear rate reversal, the method was unable to reliably measure flow dynamics close to zero. Nevertheless, the combined methodology was able to reliably assess diastolic hemodynamics. The diastolic peak flow and average diastolic resistance could be determined with a small relative error of (8 ± 7)% and (7 ± 5)%, respectively.

  13. Transport critical current of MgB2 wires: pulsed current of varying rate compared to direct current method

    Science.gov (United States)

    See, K. W.; Xu, X.; Horvat, J.; Cook, C. D.; Dou, S. X.

    2011-10-01

    The measurement of transport critical current (Ic) for MgB2 wires and tapes has been investigated with two different techniques, the conventional four-probe arrangement with direct current (DC) power source, and a tailored triangle pulse at different rates of current change. The DC method has been widely used and practiced by various groups, but suffers from inevitable heating effects when high currents are used at low magnetic fields. The pulsed current method has no heating effects, but the critical current can depend on the rate of the current change (dI/dt) in the pulse. Our pulsed current measurements with varying dI/dt show that the same values of Ic are obtained as with the DC method, but without the artifacts of heating. Our method is particularly useful at low field regions which are often inaccessible by DC methods. We also performed a finite element method (FEM) analysis to obtain the time dependent heat distribution in MgB2 due to the electric potential produced at the current contacts to the superconducting sample and its gradient around the contacts. This gradient is defined as the current transfer length (CTL) of the samples and leads to Joule heating of the wire near the contacts. The FEM results provide further evidence of the limitation of the DC method in obtaining high transport critical current.

  14. On-line fingerprinting of fluids using coaxial stub resonator technology

    NARCIS (Netherlands)

    Hoog-Antonyuk, N.A.; Olthuis, Wouter; Mayer, M.J.J.; Yntema, D.; Miedema, H.; van den Berg, Albert

    2012-01-01

    Here we demonstrate the proof-of-principle of a coaxial stub resonator to assess the dielectric properties of fluids. This radio-frequency spectroscopy method is based on coaxial stub technology and comprises quarter wave length open-ended resonators that are filled with a liquid sample as

  15. OPTIMIZATION OF TRANSIENT FEEDING TO PARALLEL-PLATE TRANSMISSION LINES FROM COAXIAL LINE

    Institute of Scientific and Technical Information of China (English)

    Tian Chunming; Wang Jianguo; Meng Fenxia; Zhang Maoyu; Ge Debiao

    2001-01-01

    The transient feeding to parallel-plate transmission lines from coaxial line is optimized by using the Finite-Difference Time-Domain (FDTD) method and a simple FDTD feed model. Observing the reflected voltages, this letter presents the optimal feeding position and ratio of width to height for a given input impedance of the coaxial line.

  16. A Return Loss Test Method for RF Coaxial Connectors%一种射频同轴连接器回波损耗的测试方法

    Institute of Scientific and Technical Information of China (English)

    田锋伟

    2013-01-01

    Return Loss is the important electrical performance,which is the key test item that can guarantee the connectors work normal y.This paper puts emphasis on the test principle,parameter setting and testing steps of the Return Loss for single RF Coaxial Connector.%  回波损耗是射频同轴连接器重要的电气性能指标,是保证射频同轴连接器能够正常使用的关键检测项目。文章较详细地阐述了单个射频同轴连接器回波损耗的测试原理、参数设定以及测试操作步骤。

  17. Risk factor analysis of pulmonary hemorrhage complicating CT-guided lung biopsy in coaxial and non-coaxial core biopsy techniques in 650 patients

    Energy Technology Data Exchange (ETDEWEB)

    Nour-Eldin, Nour-Eldin A., E-mail: nour410@hotmail.com [Institute for Diagnostic and Interventional Radiology, Johan Wolfgang Goethe – University Hospital, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Diagnostic and Interventional Radiology Department, Cairo University Hospital, Cairo (Egypt); Alsubhi, Mohammed [Institute for Diagnostic and Interventional Radiology, Johan Wolfgang Goethe – University Hospital, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Naguib, Nagy N. [Institute for Diagnostic and Interventional Radiology, Johan Wolfgang Goethe – University Hospital, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Diagnostic and Interventional Radiology Department, Alexandria University Hospital, Alexandria (Egypt); Lehnert, Thomas; Emam, Ahmed; Beeres, Martin; Bodelle, Boris; Koitka, Karen; Vogl, Thomas J.; Jacobi, Volkmar [Institute for Diagnostic and Interventional Radiology, Johan Wolfgang Goethe – University Hospital, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany)

    2014-10-15

    Purpose: To evaluate the risk factors involved in the development of pulmonary hemorrhage complicating CT-guided biopsy of pulmonary lesions in coaxial and non-coaxial techniques. Materials and methods: Retrospective study included CT-guided percutaneous lung biopsies in 650 consecutive patients (407 males, 243 females; mean age 54.6 years, SD: 5.2) from November 2008 to June 2013. Patients were classified according to lung biopsy technique in coaxial group (318 lesions) and non-coaxial group (332 lesions). Exclusion criteria for biopsy were: lesions <5 mm in diameter, uncorrectable coagulopathy, positive-pressure ventilation, severe respiratory compromise, pulmonary arterial hypertension or refusal of the procedure. Risk factors for pulmonary hemorrhage complicating lung biopsy were classified into: (a) patient's related risk factors, (b) lesion's related risk factors and (d) technical risk factors. Radiological assessments were performed by two radiologists in consensus. Mann–Whitney U test and Fisher's exact tests for statistical analysis. p values <0.05 were considered statistically significant. Results: Incidence of pulmonary hemorrhage was 19.6% (65/332) in non-coaxial group and 22.3% (71/318) in coaxial group. The difference in incidence between both groups was statistically insignificant (p = 0.27). Hemoptysis developed in 5.4% (18/332) and in 6.3% (20/318) in the non-coaxial and coaxial groups respectively. Traversing pulmonary vessels in the needle biopsy track was a significant risk factor of the development pulmonary hemorrhage (incidence: 55.4% (36/65, p = 0.0003) in the non-coaxial group and 57.7% (41/71, p = 0.0013) in coaxial group). Other significant risk factors included: lesions of less than 2 cm (p value of 0.01 and 0.02 in non-coaxial and coaxial groups respectively), basal and middle zonal lesions in comparison to upper zonal lung lesions (p = 0.002 and 0.03 in non-coaxial and coaxial groups respectively), increased lesion

  18. Wire Array Photovoltaics

    Science.gov (United States)

    Turner-Evans, Dan

    Over the past five years, the cost of solar panels has dropped drastically and, in concert, the number of installed modules has risen exponentially. However, solar electricity is still more than twice as expensive as electricity from a natural gas plant. Fortunately, wire array solar cells have emerged as a promising technology for further lowering the cost of solar. Si wire array solar cells are formed with a unique, low cost growth method and use 100 times less material than conventional Si cells. The wires can be embedded in a transparent, flexible polymer to create a free-standing array that can be rolled up for easy installation in a variety of form factors. Furthermore, by incorporating multijunctions into the wire morphology, higher efficiencies can be achieved while taking advantage of the unique defect relaxation pathways afforded by the 3D wire geometry. The work in this thesis shepherded Si wires from undoped arrays to flexible, functional large area devices and laid the groundwork for multijunction wire array cells. Fabrication techniques were developed to turn intrinsic Si wires into full p-n junctions and the wires were passivated with a-Si:H and a-SiNx:H. Single wire devices yielded open circuit voltages of 600 mV and efficiencies of 9%. The arrays were then embedded in a polymer and contacted with a transparent, flexible, Ni nanoparticle and Ag nanowire top contact. The contact connected >99% of the wires in parallel and yielded flexible, substrate free solar cells featuring hundreds of thousands of wires. Building on the success of the Si wire arrays, GaP was epitaxially grown on the material to create heterostructures for photoelectrochemistry. These cells were limited by low absorption in the GaP due to its indirect bandgap, and poor current collection due to a diffusion length of only 80 nm. However, GaAsP on SiGe offers a superior combination of materials, and wire architectures based on these semiconductors were investigated for multijunction

  19. Properties of coaxial magnetocumulative generators

    Energy Technology Data Exchange (ETDEWEB)

    Kidder, R.E.

    1983-03-14

    The properties of a coaxial magnetocumulative generator (MCG) in which the current increases exponetially with time are derived and discussed. Such an exponential MCG possess highly desirable performance characteristics that are readily derived and expressed in terms of simple formulas. It is concluded that an exponential MCG may approach a capability of delivering 100 megajoules to a 1 nanohenry load in 1 microsecond.

  20. wire chamber

    CERN Multimedia

    Multi-wire detectors contain layers of positively and negatively charged wires enclosed in a chamber full of gas. A charged particle passing through the chamber knocks negatively charged electrons out of atoms in the gas, leaving behind positive ions. The electrons are pulled towards the positively charged wires. They collide with other atoms on the way, producing an avalanche of electrons and ions. The movement of these electrons and ions induces an electric pulse in the wires which is collected by fast electronics. The size of the pulse is proportional to the energy loss of the original particle.

  1. wire chamber

    CERN Multimedia

    Was used in ISR (Intersecting Storage Ring) split field magnet experiment. Multi-wire detectors contain layers of positively and negatively charged wires enclosed in a chamber full of gas. A charged particle passing through the chamber knocks negatively charged electrons out of atoms in the gas, leaving behind positive ions. The electrons are pulled towards the positively charged wires. They collide with other atoms on the way, producing an avalanche of electrons and ions. The movement of these electrons and ions induces an electric pulse in the wires which is collected by fast electronics. The size of the pulse is proportional to the energy loss of the original particle.

  2. Wire chamber

    CERN Multimedia

    Multi-wire detectors contain layers of positively and negatively charged wires enclosed in a chamber full of gas. A charged particle passing through the chamber knocks negatively charged electrons out of atoms in the gas, leaving behind positive ions. The electrons are pulled towards the positively charged wires. They collide with other atoms on the way, producing an avalanche of electrons and ions. The movement of these electrons and ions induces an electric pulse in the wires which is collected by fast electronics. The size of the pulse is proportional to the energy loss of the original particle.

  3. wire chamber

    CERN Multimedia

    1985-01-01

    Multi-wire detectors contain layers of positively and negatively charged wires enclosed in a chamber full of gas. A charged particle passing through the chamber knocks negatively charged electrons out of atoms in the gas, leaving behind positive ions. The electrons are pulled towards the positively charged wires. They collide with other atoms on the way, producing an avalanche of electrons and ions. The movement of these electrons and ions induces an electric pulse in the wires which is collected by fast electronics. The size of the pulse is proportional to the energy loss of the original particle.

  4. SIMULATION OF ELECTROMAGNETIC PICKUP ON CCTV COAXIAL CABLE

    Directory of Open Access Journals (Sweden)

    O. V. Boiprav

    2013-01-01

    Full Text Available The utilization of computer-aided design FEKO for simulation of electromagnetic interference on coaxial cables of different types, such as those used in CCTV (RG59/U, RG11/U, RG179/U is proposed. Item and parameters selection for this simulation rationale is given. The obtained results are described and analyzed. It was found that a cable RG179U is the most vulnerable to external electromagnetic radiation among of all coaxial cables used in the CCTV design. It was revealed that the electromagnetic interference levels on coaxial cable depends on this one length and takes maximum value when it is a multiple of the external electromagnetic radiation wavelength. A method for electromagnetic interference on the cable network CCTV reduction is proposed.

  5. Electrochemical properties of Sn-based nanopowders synthesized by a pulsed wire evaporation method and effect of binder coating

    Energy Technology Data Exchange (ETDEWEB)

    Ha, Jong-Keun [School of Materials Science and Engineering & RIGET, Gyeongsang National University, 501, Jinju-daero, Jinju-si, Gyeongsangnam-do (Korea, Republic of); Song, Ju-Seok; Cho, Gyu-Bong; Ahn, Jou-Hyeon [Dept. of Materials Engineering and Convergence Technology & RIGET, Gyeongsang National University, 501, Jinju-daero, Jinju-si, Gyeongsangnam-do (Korea, Republic of); Ahn, Hyo-Jun, E-mail: ahj@gnu.ac.kr [School of Materials Science and Engineering & RIGET, Gyeongsang National University, 501, Jinju-daero, Jinju-si, Gyeongsangnam-do (Korea, Republic of); Dept. of Materials Engineering and Convergence Technology & RIGET, Gyeongsang National University, 501, Jinju-daero, Jinju-si, Gyeongsangnam-do (Korea, Republic of); Cho, Kwon-Koo, E-mail: kkcho66@gnu.ac.kr [School of Materials Science and Engineering & RIGET, Gyeongsang National University, 501, Jinju-daero, Jinju-si, Gyeongsangnam-do (Korea, Republic of); Dept. of Materials Engineering and Convergence Technology & RIGET, Gyeongsang National University, 501, Jinju-daero, Jinju-si, Gyeongsangnam-do (Korea, Republic of)

    2016-10-15

    Highlights: • Sn-based nanoparticles are fabricated by using the pulsed wire evaporation method. • The electrodes are prepared by mixing the graphene and coating the surface. • Coating the surface of electrode is used with brushing of simple and facile method. • The electrochemical measurements are performed with galvanostatic experiments. • The coating electrode maintains capacity nearly of 501 mAh g{sup −1} up to 100 cycles. - Abstract: Sn-based nanoparticles are prepared with the O{sub 2} concentrations in chamber of Ar atmosphere (by v/v) by using the pulsed wire evaporation (PWE) method. The prepared electrodes are only Sn-based powder electrode, its binder coating electrode and Sn-based powder/graphene nanocomposite electrode. Morphology and structure of the synthesized powders and electrodes are investigated with a field emission scanning electron microscope (FE-SEM) and an X-ray diffraction (XRD) analysis. The electrochemical measurements were performed with galvanostatic cycling experiments using a coin type cell of CR2032 (Ø20, T3.2 mm). The binder coating electrode is superior to others and maintains delithiation capacity nearly of 501 mAh g{sup −1} as 58.3% of first delithiation capacity at 0.2 C-rate up to 100 cycles.

  6. A hybrid surface modification method on copper wire braids for enhancing thermal performance of ultra-thin heat pipes

    Science.gov (United States)

    Sheng, W. K.; Lin, H. T.; Wu, C. H.; Kuo, L. S.; Chen, P. H.

    2017-02-01

    Copper is the most widely used material in heat pipe manufacturing. Since the capability of wick structures inside a heat pipe will dominate its thermal performance, in this study, we introduce a hybrid surface modification method on the copper wire braids being inserted as wick structure into an ultra-thin heat pipe. The hybrid method is the combination of a chemical-oxidation-based method and a sol-gel method with nanoparticles being dip-coated onto the braid. The experimental data show that braids under hybrid treatment perform higher water rising speed than the oxidized braids while owning higher water net weight than those braids being only dip-coated with nanoparticle.

  7. Estimation Methods for Determination of Drag Characteristics of Fly-by-Wire Aircraft

    Directory of Open Access Journals (Sweden)

    G. Girija

    2001-01-01

    Full Text Available "In this paper, several parameter/state estimation approaches for the determination of drag polars from flight data are described and evaluated for a fly-by-wire (FBW aircraft. Both model-based approaches (MBAs and non-model-based approaches (NMBAs are considered. Dynamic response data from roller coaster and wind- up-turn manoeuvres are generated in a FBW aircraft flight simulator at different flight conditions and the typical performance results are presented. A novel approach to estimate the drag polar has been evaluated. It has been found that the NMBAs perform better than the MBAs. Classically, the MBAs have been used for the determination of drag polars. The merits of an NMBA are that it does not require specification of the detailed model of the aerodynamic coefficients and it can be suitably used for online estimation of drag polars from the flight data of aerospace vehicles

  8. Contribution of ion beam analysis methods to the development of second generation high temperature superconducting wires

    Science.gov (United States)

    Usov, I. O.; Arendt, P. N.; Foltyn, S. R.; Stan, L.; DePaula, R. F.; Holesinger, T. G.

    2010-06-01

    One of the crucial steps in the second generation high temperature superconducting wire program was development of the buffer-layer architecture. The architecture designed at the Superconductivity Technology Center at Los Alamos National Laboratory consists of several oxide layers wherein each layer plays a specific role, namely: nucleation layer, diffusion barrier, biaxially textured template, and intermediate layer providing a suitable lattice match to the superconducting Y 1Ba 2Cu 3O 7 (YBCO) compound. This report demonstrates how a wide range of ion beam analysis techniques (SIMS, RBS, channeling, PIXE, PIGE, NRA and ERD) was employed for analysis of each buffer layer and the YBCO film. These results assisted in understanding of a variety of physical processes occurring during the buffer layer fabrication and helped to optimize the buffer-layer architecture as a whole.

  9. Coaxial Electrospinning Method for the Preparation of TiO2 @CdS/PVA Composite Nanofiber Mat and Investigation on its Photodegradation Catalysis.

    Science.gov (United States)

    Luo, Yanmei; Jia, Yiru; Zhang, Dexian; Cheng, Xinjian

    2016-07-01

    TiO2 /PVA composite nanofiber mat was prepared via an electrospinning technology. SH-TiO2 -SiO2 hybrid particles and PVA solution were injected through a coaxial syringe, yielding a composite nanofiber mat. The as-prepared SH-TiO2 -SiO2 /PVA composite nanofiber mat was immersed in Cd(2+) cation solution and S(2-) anion solution in turn. Thus, yellow TiO2 @CdS/PVA composite nanofiber mats were prepared. By adjusting the number of times a mat was immersed in the Cd(2+) and S(2-) solutions, different amounts of CdS particles attaching to the mats were obtained. Both SH-TiO2 -SiO2 /PVA and TiO2 @CdS/PVA composite nanofiber mats were employed to catalyze the photodegradation of a model dye, methylene blue. The photodegradation performance could be greatly enhanced by the introduction of CdS particles anchoring onto TiO2 particles. The photodegradation efficiency reached 99.2% within 180 min. Also, the nanofiber mat could be recycled and reused at least 10 times. The photodegradation efficiency of TiO2 @CdS/PVA composite nanofiber mats remained 68.8% for 10 cycles.

  10. A model for ferrite-loaded transversely biased coaxial resonators

    DEFF Research Database (Denmark)

    Acar, Öncel; Zhurbenko, Vitaliy; Johansen, Tom Keinicke

    2013-01-01

    This work describes a simple model for shortened coaxial cavity resonators with transversely biased ferrite elements. The ferrite allows the resonance frequency to be tuned, and the presented model provides a method of approximately calculating these frequencies to generate the tuning curve...

  11. Coaxial hybrid iron (CHI) wiggler

    Science.gov (United States)

    Jackson, Robert H.; Freund, Henry P.; Pershing, Dean E.; Taccetti, J. M.

    1993-11-01

    A magnetic wiggler design has been developed for applications in free-electron lasers which is scalable to small periods with high field amplitude, high beam current acceptance, and excellent transverse focusing and beam propagation properties. The Coaxial Hybrid Iron (CHI) wiggler design consists of a coaxial arrangement of alternating ferromagnetic and non- ferromagnetic rings with the central portion of the coax shifted by one half period. The entire arrangement is immersed in a solenoidal field which results in a cylindrically symmetric periodic field. A key advantage of this wiggler configuration is its capacity to handle very high beam currents with excellent focusing and transport properties. FEL configuration using the CHI wiggler design have the potential for high power, high frequency coherent generation in relatively compact systems. Analytic and simulated characteristics of the CHI wiggler are presented.

  12. Methods for implantation of micro-wire bundles and optimization of single/multi-unit recordings from human mesial temporal lobe

    Science.gov (United States)

    Misra, A.; Burke, J. F.; Ramayya, A. G.; Jacobs, J.; Sperling, M. R.; Moxon, K. A.; Kahana, M. J.; Evans, J. J.; Sharan, A. D.

    2014-04-01

    Objective. The authors report methods developed for the implantation of micro-wire bundles into mesial temporal lobe structures and subsequent single neuron recording in epileptic patients undergoing in-patient diagnostic monitoring. This is done with the intention of lowering the perceived barriers to routine single neuron recording from deep brain structures in the clinical setting. Approach. Over a 15 month period, 11 patients were implanted with platinum micro-wire bundles into mesial temporal structures. Protocols were developed for (A) monitoring electrode integrity through impedance testing, (B) ensuring continuous 24-7 recording, (C) localizing micro-wire position and ‘splay’ pattern and (D) monitoring grounding and referencing to maintain the quality of recordings. Main results. Five common modes of failure were identified: (1) broken micro-wires from acute tensile force, (2) broken micro-wires from cyclic fatigue at stress points, (3) poor in vivo micro-electrode separation, (4) motion artifact and (5) deteriorating ground connection and subsequent drop in common mode noise rejection. Single neurons have been observed up to 14 days post-implantation and on 40% of micro-wires. Significance. Long-term success requires detailed review of each implant by both the clinical and research teams to identify failure modes, and appropriate refinement of techniques while moving forward. This approach leads to reliable unit recordings without prolonging operative times, which will help increase the availability and clinical viability of human single neuron data.

  13. Simultaneous measurements of three velocity components by a flying hot-wire method using an x-array hot-wire probe. 2nd Report. Calibration technique and its application to a flow field downstream of a vortex generator; X gata nessen probe wo mochiita flying hot wire ho ni yoru sokudo no sanhoko seibun no doji keisoku. 2. Nessen sensor no kosei hoho to uzu hasseiki karyu no keisokurei

    Energy Technology Data Exchange (ETDEWEB)

    Shiino, T. [Nissan Motor Co. Ltd., Tokyo (Japan); Yamamoto, K.; Shizawa, T.; Honami, S. [Science University of Tokyo, Tokyo (Japan). Faculty of Engineering

    1995-12-25

    This paper proposes a calibration technique for a flying hot-wire method that uses with an X-array hot-wire probe. The flying hot-wire system moves the hot-wire probe in the span wise Z-direction of the flow field. The calibration of yaw and pitch angle sensitivities of the probe is of utmost importance to this system. After careful calibration, the system is applied to a three-dimensional flow to obtain three components of the mean velocity and six components of the Reynolds stress. The mean velocities and the Reynolds shear stresses downstream of a pair of vortex generators embedded in a two-dimensional boundary layer show the same profiles as those obtained with an ordinary X-array hot-wire probe. In one traverse, the flying hot-wire system can measure 60 points of six components of the Reynolds stress with good accuracy. 6 refs., 15 figs.

  14. Coaxial fundus camera for opthalmology

    Science.gov (United States)

    de Matos, Luciana; Castro, Guilherme; Castro Neto, Jarbas C.

    2015-09-01

    A Fundus Camera for ophthalmology is a high definition device which needs to meet low light illumination of the human retina, high resolution in the retina and reflection free image1. Those constraints make its optical design very sophisticated, but the most difficult to comply with is the reflection free illumination and the final alignment due to the high number of non coaxial optical components in the system. Reflection of the illumination, both in the objective and at the cornea, mask image quality, and a poor alignment make the sophisticated optical design useless. In this work we developed a totally axial optical system for a non-midriatic Fundus Camera. The illumination is performed by a LED ring, coaxial with the optical system and composed of IR of visible LEDs. The illumination ring is projected by the objective lens in the cornea. The Objective, LED illuminator, CCD lens are coaxial making the final alignment easily to perform. The CCD + capture lens module is a CCTV camera with autofocus and Zoom built in, added to a 175 mm focal length doublet corrected for infinity, making the system easily operated and very compact.

  15. Control for the Three-Phase Four-Wire Four-Leg APF Based on SVPWM and Average Current Method

    Directory of Open Access Journals (Sweden)

    Xiangshun Li

    2015-01-01

    Full Text Available A novel control method is proposed for the three-phase four-wire four-leg active power filter (APF to realize the accurate and real-time compensation of harmonic of power system, which combines space vector pulse width modulation (SVPWM with triangle modulation strategy. Firstly, the basic principle of the APF is briefly described. Then the harmonic and reactive currents are derived by the instantaneous reactive power theory. Finally simulation and experiment are built to verify the validity and effectiveness of the proposed method. The simulation results show that the response time for compensation is about 0.025 sec and the total harmonic distortion (THD of the source current of phase A is reduced from 33.38% before compensation to 3.05% with APF.

  16. The Terminal Responses of the Two-Wire Line in Multiaperture Cavities Based on Electromagnetic Topology and Method of Moments

    Directory of Open Access Journals (Sweden)

    Ying Li

    2011-01-01

    Full Text Available A simulation technique based on electromagnetic topology (EMT theory is proposed for analyzing electromagnetic interference (EMI coupling through apertures onto the two-transmission line enclosed within metallic structures. The electromagnetic interactions between apertures and the external-internal interactions were treated through the topological decomposition and the multistep iterative method. Then, the load responses of the two-wire transmission line are resolved by the the Baum-Liu-Tesche (BLT equation. The simulation results both without and with the electromagnetic interaction are presented for the frequency range from 100 MHz to 3 GHz. These numerical results obtained by two methods imply that the electromagnetic interaction cannot be simply ignored, especially for the frequency range up to 1 GHz.

  17. Study of Mode Coupling on Coaxial Resonators

    Institute of Scientific and Technical Information of China (English)

    Rui Liu; Hong-Fu Li

    2011-01-01

    A study of mode coupling phenomenon of coaxial resonators has been conducted with theories.Through establishing the source-free transmission line equation,boundary conditions of the coaxial resonators with a corrugated inner conductor are analyzed.In the end,calculations are performed in a wide range of corrugation parameters for the resonator of the Karisruhe Institute of Technology (KIT) relevant coaxial gyrotron.

  18. Graphite coating effects on the critical current characteristics of MgB{sub 2}/Cu wires fabricated by an in situ PIT method

    Energy Technology Data Exchange (ETDEWEB)

    Shimura, S. [Morioka Laboratory for Applied Superconductivity Technology, Superconductivity Research Laboratory, ISTEC, 3-35-2 Iioka-Shinden, Morioka, Iwate 020-0852 (Japan)]. E-mail: shimura@istec.or.jp; Machi, T. [Superconductivity Research Laboratory, ISTEC 1-10-13 Shinonome, Koto-ku, Tokyo 135-0062 (Japan); Nakao, K. [Superconductivity Research Laboratory, ISTEC 1-10-13 Shinonome, Koto-ku, Tokyo 135-0062 (Japan); Koshizuka, N. [Morioka Laboratory for Applied Superconductivity Technology, Superconductivity Research Laboratory, ISTEC, 3-35-2 Iioka-Shinden, Morioka, Iwate 020-0852 (Japan); Tanaka, S. [Superconductivity Research Laboratory, ISTEC 1-10-13 Shinonome, Koto-ku, Tokyo 135-0062 (Japan); Mochizuki, K. [Tokyo Wire Works, Ltd., 2-30-9 Nishi-Rokugo, Ota-ku, Tokyo 144-0056 (Japan); Shibata, N. [Iwate Tokyo Wire Works, Ltd., 2-30-9 Nishi-Rokugo, Ota-ku, Tokyo 144-0056 (Japan); Ushio, K. [Iwate Tokyo Wire Works, Ltd., 2-30-9 Nishi-Rokugo, Ota-ku, Tokyo 144-0056 (Japan)

    2005-10-01

    In order to improve the critical current characteristics of Cu sheathed MgB{sub 2} wires, we studied the carbon doping and coating effects on J {sub C} of wires prepared by an in situ powder-in-tube (PIT) method. Raw materials of Mg and B powders were mixed with a certain amount of MgB{sub 2} powder to increase the core density of wires in the heat treated samples. The pellets of these mixed powders were inserted into Cu sheaths and manufactured into wires by rotary swaging, two-axial rolling and drawing under cold-working. The wires were finally heat treated at 600 deg. C for 2 h in Ar gas atmosphere. The critical current I {sub C} of short samples of graphite 5 at.% doped MgB{sub 2}/Cu with diameter of 1.0 mm reached 548 A (J {sub C} = 440 kA/cm{sup 2}) at 4.2 K in self-field. The reaction of Mg with Cu decreased for graphite coating samples compared with non-coating ones. We obtained high performance MgB{sub 2}/Cu wires by doping of diamond and graphite powder in the in situ PIT method. We found that the graphite coating on the inside surface of Cu sheath was effective for suppressing the reaction of Mg with Cu sheath. We also fabricated solenoid coils by wind and react method heat treated under the above conditions. The I {sub C} value was 230 A at 4.2 K for a coil produced by using a 16 m wire. This coil generated a magnetic field of 0.42 T at liquid He temperature.

  19. Graphite coating effects on the critical current characteristics of MgB 2/Cu wires fabricated by an in situ PIT method

    Science.gov (United States)

    Shimura, S.; Machi, T.; Nakao, K.; Koshizuka, N.; Tanaka, S.; Mochizuki, K.; Shibata, N.; Ushio, K.

    2005-10-01

    In order to improve the critical current characteristics of Cu sheathed MgB2 wires, we studied the carbon doping and coating effects on JC of wires prepared by an in situ powder-in-tube (PIT) method. Raw materials of Mg and B powders were mixed with a certain amount of MgB2 powder to increase the core density of wires in the heat treated samples. The pellets of these mixed powders were inserted into Cu sheaths and manufactured into wires by rotary swaging, two-axial rolling and drawing under cold-working. The wires were finally heat treated at 600 °C for 2 h in Ar gas atmosphere. The critical current IC of short samples of graphite 5 at.% doped MgB2/Cu with diameter of 1.0 mm reached 548 A (JC = 440 kA/cm2) at 4.2 K in self-field. The reaction of Mg with Cu decreased for graphite coating samples compared with non-coating ones. We obtained high performance MgB2/Cu wires by doping of diamond and graphite powder in the in situ PIT method. We found that the graphite coating on the inside surface of Cu sheath was effective for suppressing the reaction of Mg with Cu sheath. We also fabricated solenoid coils by wind and react method heat treated under the above conditions. The IC value was 230 A at 4.2 K for a coil produced by using a 16 m wire. This coil generated a magnetic field of 0.42 T at liquid He temperature.

  20. Substrate Integrated Evanescent Filters Employing Coaxial Stubs

    DEFF Research Database (Denmark)

    Zhurbenko, Vitaliy

    2015-01-01

    Evanescent mode substrate integrated waveguide (SIW) is one of the promising technologies for design of light-weight low-cost microwave components. Traditional realization methods used in the standard evanescent waveguide technology are often not directly applicable to SIW due to dielectric filling...... and small height of the waveguide. In this work, one of the realization methods of evanescent mode waveguides using a single layer substrate is considered. The method is based on the use of coaxial stubs as capacitive susceptances externally connected to a SIW. A microwave filter based on these principles...... of the microwave filter are discussed. The approach is useful in applications where a sharp roll-off at the upper stop-band is required....

  1. Electrochemical properties of Sn/C nanoparticles fabricated by redox treatment and pulsed wire evaporation method

    Science.gov (United States)

    Song, Ju-Seok; Cho, Gyu-Bong; Ahn, Jou-Hyeon; Cho, Kwon-Koo

    2017-09-01

    Tin (Sn) based anode materials are the most promising anode materials for lithium-ion batteries due to their high theoretical capacity corresponding to the formation of Li4.4Sn composition (Li4.4Sn, 994 mAh/g). However, the applications of tin based anodes to lithium-ion battery system are generally limited by a large volume change (>260%) during lithiation and delithiation cycle, which causes pulverize and poor cycling stability. In order to overcome this shortcoming, we fabricate a Sn/C nanoparticle with a yolk-shell structure (Sn/void/C) by using pulsed wire evaporation process and oxidation/reduction heat treatment. Sn nanoparticles are encapsulated by a conductive carbon layer with structural buffer that leaves enough room for expansion and contraction during lithium insertion/desertion. We expect that the yolk-shell structure has the ability to accommodate the volume changes of tin and leading to an improved cycle performance. The Sn/Void/C anode with yolk-shell structure shows a high specific capacity of 760 mAh/g after 50 cycles.

  2. Influence of Flaws of Wire Rod Surface, Inclusions and Voids on Wire Breaks in Superfine Wire Drawing

    Science.gov (United States)

    Yoshida, Kazunari; Norasethasopon, Somchai; Shinohara, Tetsuo; Ido, Ryuta

    By means of the finite element analysis (FEA), this study analyzed wire breaks that occurred in the drawing fine wires containing flaws on the wire surface, inclusion and void. The deformation behavior of an inclusion was examined, in which the inclusion's location is assumed to be on the center axis of the wire, and the cause of wire breaks and their prevention method were clarified. It was found that an inclusion diameter/wire diameter ratio of 0.4 or higher increases the likelihood of wire breaks occurring. When the inclusion is not assumed to be in the center axis of the wire, it was also found that necking and wire breaks appear more frequently. FEA showed that a flaw grows with each processing step, when a small circumferential flaw is placed on the wire rod surface, and eventually becomes a surface defect, which is called a check mark in practice.

  3. O método de fio quente: técnica em paralelo e técnica de superfície The hot wire method: the hot wire parallel technique and the hot wire surface technique

    Directory of Open Access Journals (Sweden)

    W. N. dos Santos

    2002-06-01

    Full Text Available A condutividade térmica é uma das propriedades físicas mais importantes de um material. A sua determinação experimental apresenta algumas dificuldades e requer alta precisão na determinação dos fatores necessários para o seu cálculo. O método de medida de condutividade térmica para materiais refratários mais usado hoje em todo o mundo, tanto nos centros de pesquisa, quanto nos laboratórios industriais, é o Método do Fio Quente, onde a condutividade térmica é calculada a partir do transiente de temperatura gerado por uma fonte de calor ideal, infinitamente longa e fina num meio material infinito. Neste trabalho são comparados os resultados obtidos utilizando-se duas técnicas diferentes para a detecção do transiente térmico: numa delas, a temperatura é medida na superfície do fio quente, (técnica de fio quente de superfície, e na outra, a temperatura é medida a uma certa distância do fio quente (técnica de fio quente paralelo. Os resultados experimentais mostram uma grande vantagem da técnica de fio quente de superfície em relação a técnica de fio quente paralelo para materiais com condutividade térmica superior a 10 W/mK. O intervalo de tempo considerado no cálculo é bem maior que aquele que seria utilizado na técnica de fio quente paralelo, obtendo-se assim resultados mais precisos e confiáveis.Thermal conductivity is one of the most important physical properties of a material. However, its experimental evaluation may presents some specific troubles, and high precision in the determination of the factors involved in its calculation is required. Specifically for refractory materials, the experimental technique employed worldwide for thermal conductivity calculations is the hot wire technique, in which the thermal conductivity is calculated starting from the temperature transient generated by an ideal, infinitely thin and long heat source embedded in an infinite surrounding material. In this work comparisons

  4. A method of measuring the three-dimensional mean flow and turbulence quantities inside a rotating turbo-machinery passage. [by hot-wire anemometer

    Science.gov (United States)

    Gorton, C. A.; Lakshminarayana, B.

    1975-01-01

    A method of measuring the three-dimensional components of mean velocity and turbulence quantities within a rotating turbomachinery passage is developed through the use of hot wire anemometry techniques. Equations are derived which, when solved simultaneously and in conjunction with the data obtained from the hot wire anemometer measurements, will provide values for the radial, axial and tangential components of mean velocity, turbulence intensity and turbulence stress within the rotating turbomachinery passage. A three-bladed rocket pump inducer model, operating in air, was used in the experimentation. The method is very accurate and provides very useful information on the characteristics of the flow inside rotor passages hitherto unexplored.

  5. An Oscillating Boundary Temperature Method for the Determination of Transient Thermal Conductivity and Internal Heat Generation with a Comparison to a Transient Hot-Wire Method

    Science.gov (United States)

    Chirdon, William M.; Patil, Abhijeet P.

    2011-10-01

    An oscillating boundary temperature (OBT) method is proposed to simultaneously determine transient thermal properties including thermal conductivity, thermal diffusivity, internal heat generation, and volumetric heat capacity for exothermic solids and semi-solids over a narrow, controlled temperature range by using internal temperature measurements of the thermal wave. A comparison of this method and a transient hot-wire (THW) method is conducted in the presence of heat generation using physical properties which change over time. The advantages and disadvantages of both methods are discussed. The OBT method is potentially useful for the analysis of exothermic solid or semi-solid materials such as hydrating (freshly mixed) cement and concrete, polymers and composites undergoing polymerization reactions, and biological tissues.

  6. A General Method for Preparing Anatase TiO2 Treelike-Nanoarrays on Various Metal Wires for Fiber Dye-Sensitized Solar Cells

    Science.gov (United States)

    Chu, Liang; Li, Luying; Su, Jun; Tu, Fanfan; Liu, Nishuang; Gao, Yihua

    2014-03-01

    Anatase TiO2 tree-like nanoarrays were prepared on various metal wires (Ti, W, Ni, etc.) through one-step facile hydrothermal reaction. The anatase TiO2 tree-like nanoarrays consist of long TiO2 nanowire trunks with direct charge transport channels, and a large number of short TiO2 nanorod branches with large surface areas. Fiber dye-sensitized solar cells (FDSSCs) based on the anatase TiO2 tree-like nanoarrays deposited on Ti wires can achieve outstanding power conversion efficiency (PCE) of 6.32%, while FDSSCs on W wires have lower PCE of 3.24% due to the formation of WO3 layer, which might enhance recombination of charges. When the substrate is changed to a Nicole oxide wire, a novel p-n heterojunction can be obtained. This universal method is simple, facile, and low cost for preparing anatase TiO2 treelike-nanoarrays on various metal wires, which may find potential applications in fabrication of optoelectronic devices.

  7. The Design of Passive Optical Networking+Ethernet over Coaxial Cable Access Networking and Video-on-Demand Services Carrying

    Science.gov (United States)

    Ji, Wei

    2013-07-01

    Video on demand is a very attractive service used for entertainment, education, and other purposes. The design of passive optical networking+Ethernet over coaxial cable accessing and a home gateway system is proposed. The network integrates the passive optical networking and Ethernet over coaxial cable to provide high dedicated bandwidth for the metropolitan video-on-demand services. Using digital video broadcasting, IP television protocol, unicasting, and broadcasting mechanisms maximizes the system throughput. The home gateway finishes radio frequency signal receiving and provides three kinds of interfaces for high-definition video, voice, and data, which achieves triple-play and wire/wireless access synchronously.

  8. Minimization and Mitigation of Wire EDM Cutting Errors in the Application of the Contour Method of Residual Stress Measurement

    Science.gov (United States)

    Ahmad, Bilal; Fitzpatrick, Michael E.

    2016-01-01

    The contour method of residual stress measurement relies on the careful application of wire electro-discharge machining (WEDM) for the cutting stage. Changes in material removal rates during the cut lead to errors in the final calculated values of residual stress. In this study, WEDM cutting parameters have been explored to identify the optimum conditions for contour method residual stress measurements. The influence of machine parameters on the surface roughness and cutting artifacts in the contour cut is discussed. It has been identified that the critical parameter in improving the surface finish is the spark pulse duration. A typical cutting artifact and its impact on measured stress values have been identified and demonstrated for a contour cut in a welded marine steel. A procedure is presented to correct contour displacement data from the influence of WEDM cutting artifacts, and is demonstrated on the correction of a measured weld residual stress. The corrected contour method improved the residual stress magnitude up to 150 MPa. The corrected contour method results were validated by X-ray diffraction, incremental center hole drilling, and neutron diffraction.

  9. Development and testing of advanced redundancy management methods for the F-8 DFBW aircraft. [failure detection for Digital Fly By Wire systems

    Science.gov (United States)

    Deyst, J.; Deckert, J.; Desai, M.; Willsky, A.

    1977-01-01

    A reliable aircraft sensor failure detection and identification (FDI) technique is presented. The technique exploits the kinematic and dynamic relationships that exist between variables measured by dissimilar sensors to identify failures in the sensors. The method is applied to management of dual redundant sensors on the NASA F-8 digital fly-by-wire (DFBW) research aircraft.

  10. 灼热丝试验的设备确认方法及注意事项%The Verification Methods of Apparatus and Notes of the Glow-wire Test

    Institute of Scientific and Technical Information of China (English)

    陈向阳; 郭艳萍

    2015-01-01

    结合灼热丝试验装置和成品灼热丝可燃性试验方法标准要求,阐述灼热丝试验设备技术指标的确认方法,总结灼热丝试验中的注意事项.%This paper elaborates the verification methods of the glow wire test apparatus technical indicators, giving the notes of the glow wire test, while based on the standards of Glow-wire apparatus and the standard of Glow-wire flammability test method for end-products.

  11. Mechanical properties of Fe-Si-B amorphous wires produced by in-rotating-water spinning method

    Science.gov (United States)

    Hagiwara, M.; Inoue, A.; Masumoto, T.

    1982-03-01

    Amorphous wires with high strength and good ductility have been produced in Fe-Si-B alloy system by the modified melt-spinning technique in which a melt stream is ejected into a rotating water layer. These wires have a circular cross section and smooth peripheral surface. The diameter is in the range of about 0.07 to 0.27 mm. Their Vickers hardness (Hv) and tensile strength (σf) increase with silicon and boron content and reach 1100 DPN and 3920 MPa, respectively, for Fe70Si10B20, exceeding the values of heavily cold-drawn steel wires. Fracture elongation (ɛ f ), including elastic elongation, is about 2.1 to 2.8 pct. An appropriate cold drawing results in the increase of σf and ɛf by about eight and 65 pct, respectively. This increase is interpreted to result from an interaction among crossing deformation bands introduced by cold drawing. The undrawn and drawn amorphous wires are so ductile that no cracks are observed, even after closely contacted bending. Further, it is demonstrated that the σf of the Fe75Si10Bl5 amorphous wire increases by the replacement of iron with a small amount of tantalum, niobium, tungsten, molybdenum, or chromium without detriment to the formation tendency of an amorphous wire. Such iron-based amorphous wires are attractive as fine gauge, high strength materials because of their uniform shape and superior mechanical qualities.

  12. Dispersion Equation of the Coaxial-Radial Line

    Institute of Scientific and Technical Information of China (English)

    WANG Wenxiang; YUE Lingna; YU Guofen; GONG Yubing; HUANG Minzhi

    2004-01-01

    An all-metal slow-wave structure,coaxial-radial line,which is suitable for application in broadband high power traveling wave tube (TWT) and relativistic TWT as a RF system is introduced.Making use of the field matching method and variational method together with the orthogonality of the Bessel function and the Floquet Theroem for the periodic system,the dispersion characteristic expression is derived.This equation is more rigorous than that of precious reports.

  13. 开尔文四线测试方式在PCB测试机中的应用%The Application of the Kelvin Four-Wire Testing Method in PCB Testing Machine

    Institute of Scientific and Technical Information of China (English)

    刘懿俊

    2013-01-01

    分析了PCB测试机中的普通二线式测试原理、开尔文(Kelvin)四线测量方法原理,介绍了开尔文四线测量方法的优点。%This report aimed to analyze the two-wire and four-wire kelvin measurement principle in PCB testing machine , discused the advantage of Kelvin Four-Wire Testing method in PCB testing.

  14. Texture development in Galfenol wire

    Science.gov (United States)

    Boesenberg, A. J.; Restorff, J. B.; Wun-Fogle, M.; Sailsbury, H.; Summers, E.

    2013-05-01

    Galfenol (Fe-Ga alloy) wire fabrication provides a low cost alternative to directional solidification methods. This work evaluates the compositional dependence of the wire drawing suitability of Fe-Ga and characterizes the microstructural and magnetic properties of these wires. Wire has been produced with Ga contents between 10 at. % and 17 at. % to allow determination of the ductile to brittle transition (DTBT) in wire manufacture. Published results on chill cast bend specimens indicated that a DTBT occurs at roughly 15 at. % Ga. This DTBT was observed under tensile loading with a corresponding change in fracture behavior from transverse fracture to intergranular fracture. For improved magnetostrictive performance, higher Ga contents are desired, closer to the 17 at. % Ga evaluated in this work. Electron backscattered diffraction B-H loop and resonance measurements as a function of magnetic field (to determine modulus and coupling factor) are presented for as-drawn, furnace, and direct current (DC) annealed wire. Galfenol wire produced via traditional drawing methods is found to have a strong (α) texture parallel to the drawing direction. As-drawn wire was observed to have a lower magnetic permeability and larger hysteresis than DC annealed wire. This is attributed to the presence of a large volume of crystalline defects; such as vacancies and dislocations.

  15. Monte Carlo Simulation of the Coaxial Electrons Backscattering from Thin Films

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    By using the Monte Carlo method, we simulated the trajectories of coaxial backscattering electrons corresponding to a new type of scanning electron microscope. From the calculated results, we obtain a universal expression, which describes with good accuracy the backscattering coefficient versus film thickness under all conditions used. By measuring the coaxial backscattering coefficient and using this universal formula, the thickness of thin films can be determined if the composition is known.

  16. Enhanced C-band Coaxial Orthomode Transducer

    Directory of Open Access Journals (Sweden)

    S. I. Piltyay

    2014-09-01

    Full Text Available Introduction. In this paper a novel configuration of wideband coherent coaxial OMT is presented. General Design of an Orthomode Transducer. The OMT consists of elements of 3 main types: a turnstile junction between coaxial quad-ridged waveguide and 4 coaxial transmission lines; 4 coaxial transmission lines of LMR400 type; 2 antiphase power combiners/dividers. A Turnstile Junction Optimization. The optimization of a turnstile junction has been performed. Its minimized reflection coefficient is less than −28 dB in the operation frequency band 3.4–5.4 GHz. A Wideband Antiphase Power Combiner/Divider. The optimization of an antiphase power combiner/divider has been performed. Its minimized reflection coefficient is less than −38 dB. Characteristics of Coaxial Orthomode Transducer Developed. The simulation of OMT characteristics has been performed using CST Design Studio software. Conclusions. A wideband coherent coaxial orthomode transducer has been developed for the operation frequency band 3.4–5.4 GHz. In this frequency band the reflection coefficient of OMT is less than −24 dB and its crosspolar isolation exceeds 38 dB. The wideband coaxial OMT developed can be used in dual-polarized multiband antennas for satellite telecommunications and for radioastronomy.

  17. Enhanced C-band Coaxial Orthomode Transducer

    Directory of Open Access Journals (Sweden)

    S. I. Piltyay

    2014-06-01

    Full Text Available Introduction. In this paper a novel configuration of wideband coherent coaxial OMT is presented. General Design of an Orthomode Transducer. The OMT consists of elements of 3 main types: a turnstile junction between coaxial quad-ridged waveguide and 4 coaxial transmission lines; 4 right-angle coaxial junctions for each polarization; 2 antiphase power combiners/dividers. A Turnstile Junction Optimization. The optimization of a turnstile junction has been performed. Its minimized reflection coefficient is less than −28 dB in the operation frequency band 3.4–5.4 GHz. An Optimized Right-Angle Coaxial Junction. A right-angle coaxial junction has been optimized to provide reflection coefficient, which is less than −42 dB in the operation frequency band 3.4–5.4 GHz. An Antiphase Power Combiner/Divider. The optimization of an antiphase power com-biner/divider has been performed. Its minimized reflection coefficient is less than −38 dB. Conclusions. A wideband coaxial orthomode transducer has been developed for the operation frequency band 3.4–5.4 GHz. In this frequency band the reflection coefficient is less than −27 dB.

  18. Analysis of Different Positions of Fiber-Reinforced Composite Retainers versus Multistrand Wire Retainers Using the Finite Element Method

    Directory of Open Access Journals (Sweden)

    Arezoo Jahanbin

    2014-01-01

    Full Text Available Background. The aim of this study was to evaluate root displacement of the lower incisors fixed with FRC in different positions versus FSW retainers using the finite element method. Materials and Methods. 3D finite element models were designed for a mandibular anterior segment: Model 1: flexible spiral wire bonded to the lingual teeth surfaces, Model 2: FRC bonded to the upper third of lingual teeth surfaces, and Model 3: FRC bonded to the middle third. FE analysis was performed for three models and then tooth displacements were evaluated. Results. In contrast to lateral incisors and canines, the FSW retainer caused the central teeth to move more than the teeth bonded with FRC in both loadings. Comparison between Models 2 and 3 (in vertical loading showed that FRC retainers that bonded at the upper third of lingual teeth surfaces made central and canine teeth move less than FRC retainers bonded at the middle third; however, for lateral teeth it was the opposite. Conclusion. FRC retainers bonded at the upper third of lingual teeth surfaces make central and canine teeth move less than FRC retainers bonded at the middle third in vertical loading; however, for lateral teeth it was the opposite.

  19. Coaxial electrospinning for encapsulation and controlled release of fragile water-soluble bioactive agents.

    Science.gov (United States)

    Jiang, Hongliang; Wang, Liqun; Zhu, Kangjie

    2014-11-10

    Coaxial electrospinning is a robust technique for one-step encapsulation of fragile, water-soluble bioactive agents, including growth factors, DNA and even living organisms, into core-shell nanofibers. The coaxial electrospinning process eliminates the damaging effects due to direct contact of the agents with organic solvents or harsh conditions during emulsification. The shell layer serves as a barrier to prevent the premature release of the water-soluble core contents. By varying the structure and composition of the nanofibers, it is possible to precisely modulate the release of the encapsulated agents. Promising work has been done with coaxially electrospun non-woven mats integrated with bioactive agents for use in tissue engineering, in local delivery and in wound healing, etc. This paper reviews the origins of the coaxial electrospinning method, its updated status and potential future developments for controlled release of the class of fragile, water-soluble bioactive agents.

  20. Thermal Hydraulic Stability in a Coaxial Thermosyphon

    Institute of Scientific and Technical Information of China (English)

    YANG Jianhui; LU Wenqiang; LI Qing; LI Qiang; ZHOU Yuan

    2005-01-01

    The heat transfer and thermal hydraulic stability in a two-phase thermosyphon with coaxial riser and down-comer has been experimentally investigated and theoretically analyzed to facilitate its application in cold neutron source. The flow in a coaxial thermosyphon was studied experimentally for a variety of heating rates, transfer tube lengths, charge capacities, and area ratios. A numerical analysis of the hydraulic balance between the driving pressure head and the resistance loss has also been performed. The results show that the presented coaxial thermosyphon has dynamic performance advantages relative to natural circulation in a boiling water reactor.

  1. 4D Emittance Measurements Using Multiple Wire and Waist Scan Methods in the ATF Extraction Line

    Energy Technology Data Exchange (ETDEWEB)

    Rimbault, C.; Bambade, P.; Brossard, J.; /Orsay, LAL; Alabau, M.; /Valencia U., IFIC; Kuroda, S.; /KEK, Tsukuba; Scarfe, A.; /Manchester U.; Woodley, M.; /SLAC

    2011-11-02

    Emittance measurements performed in the diagnostic section of the Accelerator Test Facility (ATF) extraction line since 1998 led to vertical emittances three times larger than the expected ones, with a strong dependence on intensity. An experimental program is pursued to investigate potential sources of emittance growth and find possible remedies. This requires efficient and reliable emittance measurement techniques. In the past, several phase-space reconstruction methods developed at SLAC and KEK have been used to estimate the vertical emittance, based on multiple location beam size measurements and dedicated quadrupole scans. These methods have been shown to be very sensitive to measurement errors and other fluctuations in the beam conditions. In this context new emittance measurements have been performed revisiting these methods and newly developed ones with a systematic approach to compare and characterise their performance in the ATF extraction line.

  2. Use of quality planning methods in optimizing welding wire quality characteristics

    Directory of Open Access Journals (Sweden)

    D. Vykydal

    2013-10-01

    Full Text Available The quality of a product is given by the extent, to which the product meets customer requirements. It is generally accepted that the extent, to which the product meets such customer requirements, and, consequently, the resulting quality of the product itself, substantially depend on the early stages of the product lifecycle, i.e. on the design and development stages. Appropriate means for effective product quality planning can be found among quality management methods and tools. These methods are typically employed in engineering production and automotive industry. This paper focuses on exploring the potential of Quality Function Deployment (QFD and Failure Mode and Effect Analysis (FMEA methods for use in metallurgical production, an industrial branch where they have not been commonly employed as yet.

  3. Coaxial charged particle energy analyzer

    Science.gov (United States)

    Kelly, Michael A. (Inventor); Bryson, III, Charles E. (Inventor); Wu, Warren (Inventor)

    2011-01-01

    A non-dispersive electrostatic energy analyzer for electrons and other charged particles having a generally coaxial structure of a sequentially arranged sections of an electrostatic lens to focus the beam through an iris and preferably including an ellipsoidally shaped input grid for collimating a wide acceptance beam from a charged-particle source, an electrostatic high-pass filter including a planar exit grid, and an electrostatic low-pass filter. The low-pass filter is configured to reflect low-energy particles back towards a charged particle detector located within the low-pass filter. Each section comprises multiple tubular or conical electrodes arranged about the central axis. The voltages on the lens are scanned to place a selected energy band of the accepted beam at a selected energy at the iris. Voltages on the high-pass and low-pass filters remain substantially fixed during the scan.

  4. Measurement of the thermal conductivity of carbon nanotube--tissue phantom composites with the hot wire probe method.

    Science.gov (United States)

    Sarkar, Saugata; Zimmermann, Kristen; Leng, Weinan; Vikesland, Peter; Zhang, Jianfei; Dorn, Harry; Diller, Thomas; Rylander, Christopher; Rylander, Marissa Nichole

    2011-06-01

    Developing combinatorial treatments involving laser irradiation and nanoparticles require an understanding of the effect of nanoparticle inclusion on tissue thermal properties, such as thermal conductivity. This information will permit a more accurate prediction of temperature distribution and tumor response following therapy, as well as provide additional information to aid in the selection of the appropriate type and concentration of nanoparticles. This study measured the thermal conductivity of tissue representative phantoms containing varying types and concentrations of carbon nanotubes (CNTs). Multi-walled carbon nanotubes (MWNTs, length of 900-1200 nm and diameter of 40-60 nm), single-walled carbon nanotubes (SWNTs, length of 900-1200 nm and diameter hot wire probe method. Increasing CNT concentration from 0 to 1.0 mg/mL caused the thermal conductivity of phantoms containing SWNTs, SWNHs, and MWNTs to increase by 24, 30, and 66%, respectively. For identical CNT concentrations, phantoms containing MWNTs possessed the highest thermal conductivity.

  5. Polar interface and surface optical vibration spectra in multi-layer wurtzite quantum wires:transfer matrix method

    Institute of Scientific and Technical Information of China (English)

    Zhang Li

    2006-01-01

    The polar interface optical (IO) and surface optical (SO) phonon modes and the corresponding Frohlich electronphonon-interaction Hamiltonian in a freestanding multi-layer wurtzite cylindrical quantum wire (QWR) are derived and studied by employing the transfer matrix method in the dielectric continuum approximation and Loudon's uniaxial crystal model. A numerical calculation of a freestanding wurtzite GaN/AlN QWR is performed. The results reveal that for a relatively large azimuthal quantum number m or wave-number kz in the free z-direction, there exist two branches of IO phonon modes localized at the interface, and only one branch of SO mode localized at the surface in the system.The degenerating behaviours of the IO and SO phonon modes in the wurtzite QWR have also been clearly observed for a smallkz or m. The limiting frequency properties of the IO and SO modes for large kz and m have been explained reasonably from the mathematical and physical viewpoints. The calculations of electron-phonon coupling functions show that the high-frequency IO phonon branch and SO mode play a more important role in the electron-phonon interaction.

  6. Needleless coaxial electrospinning: A novel approach to mass production of coaxial nanofibers.

    Science.gov (United States)

    Vysloužilová, Lucie; Buzgo, Matej; Pokorný, Pavel; Chvojka, Jiří; Míčková, Andrea; Rampichová, Michala; Kula, Jiří; Pejchar, Karel; Bílek, Martin; Lukáš, David; Amler, Evžen

    2017-01-10

    Herein, we describe a simple spinneret setup for needleless coaxial electrospinning that exceeds the limited production capacity of current approaches. The proposed weir spinneret enables coaxial electrospinning from free liquid surface. This approach leads to the formation of coaxial nanofibers with higher and uniform shell/core ratio, which results in the possibility of better tuning of the degradation rate. The throughput and quality increase favor the broader application of coaxial nanofibers from weir spinnerets as systems for controlled drug delivery in regenerative medicine and tissue engineering.

  7. Electric wiring domestic

    CERN Document Server

    Coker, A J

    1992-01-01

    Electric Wiring: Domestic, Tenth Edition, is a clear and reliable guide to the practical aspects of domestic electric wiring. Intended for electrical contractors, installation engineers, wiremen and students, its aim is to provide essential up to date information on modern methods and materials in a simple, clear, and concise manner. The main changes in this edition are those necessary to bring the work into line with the 16th Edition of the Regulations for Electrical Installations issued by the Institution of Electrical Engineers. The book begins by introducing the basic features of domestic

  8. Oxidative heat release intensity in coal at low temperatures measured by the hot-wire method

    Institute of Scientific and Technical Information of China (English)

    YANG Yong-liang; LI Zeng-hua; PAN Shang-kun; GAO Si-yuan; WANG Ya-li

    2009-01-01

    Directly measuring the oxidative heat release intensity at low temperatures is difficult at present. We developed a new method based on heat conduction theory that directly measures heat release intensity of loose coal at low temperatures. Using this method, we calculated the oxidative heat release intensity of differently sized loose coals by comparing the temperature rise of the coal in nitrogen or an air environment. The results show that oxidation heat release intensity of Shenhua coal sized 0-15 mm is 0.001~0.03 W/m3 at 30~90℃ and increases with increasing temperature. The heat release intensity at a given temperature is larger for smaller sized coal. The temperature effect on heat release intensity is muted as the coal size increases. At lower temperature the change in heat release intensity as a function of size becomes smaller. These results show that the test system is usable for practical applications and is easy to operate and is capable of measuring mass samples.

  9. Relationship of roughness of building stones on the effective thermal conductivity determined by transient hot-wire method

    Science.gov (United States)

    Benoit, Merckx; Jean-Didier, Mertz; Patrick, Dudoignon; David, Giovannacci; Jean-Philippe, Garnier

    2013-04-01

    Alteration of inorganic materials in monuments is mainly related to relative humidity change in the porous network. Characterization of water content is a complex issue, specially in case of non-intrusive measurement. An innovative method is developed to quantify the water content using a direct calculation of the thermal conductivity. In order to validate the non-intrusive application to heritage stone, a control of the influence of the rock-sensor interface is required. The study was carried out on five sedimentary french rocks : three limestones (lithographic, oolithic and micritic), a sandstone of Fontainebleau and the so-called Tuffeau limestone. The textural properties are characterized by optical and electronical microscopy, X-ray diffraction, and mercury intrusion porosimetry. The transient hot-wire method is useful to obtain a quick value of effective conductivity of material. Initially used in liquids and gas, It's now more and more used for solid materials. The calculation of one effective thermal conductivity is formulated by the slope of recorded DT/ln(t) diagrams. In case of continuous and homogeneous media, only one slope can be measured. For heterogeneous solids a typical curve present two slopes : the first one measured in the short time acquisitions (arithmetic average roughness (Sa) is ranged between 44 µm and 1 µm, respectively for the coarse-grained limestone (Bretigny) and the finest one (Migné). According to the relative error of the apparatus (10%), the conductivity value is constant, independently of the surface polishing state. Thus, this evolution confirms that the method could be used on many stony materials as they are present in the built cultural heritage.

  10. Arc Plasma Gun With Coaxial Powder Feed

    Science.gov (United States)

    Zaplatynsky, Isidor

    1988-01-01

    Redesigned plasma gun provides improved metallic and ceramic coatings. Particles injected directly through coaxial bore in cathode into central region of plasma jet. Introduced into hotter and faster region of plasma jet.

  11. Plasmonic coaxial waveguide-cavity devices.

    Science.gov (United States)

    Mahigir, Amirreza; Dastmalchi, Pouya; Shin, Wonseok; Fan, Shanhui; Veronis, Georgios

    2015-08-10

    We theoretically investigate three-dimensional plasmonic waveguide-cavity structures, built by side-coupling stub resonators that consist of plasmonic coaxial waveguides of finite length, to a plasmonic coaxial waveguide. The resonators are terminated either in a short or an open circuit. We show that the properties of these waveguide-cavity systems can be accurately described using a single-mode scattering matrix theory. We also show that, with proper choice of their design parameters, three-dimensional plasmonic coaxial waveguide-cavity devices and two-dimensional metal-dielectric-metal devices can have nearly identical transmission spectra. Thus, three-dimensional plasmonic coaxial waveguides offer a platform for practical implementation of two-dimensional metal-dielectric-metal device designs.

  12. Wire Chamber

    CERN Multimedia

    1986-01-01

    Two wire chambers made originally for the R807 Experiment at CERN's Intersecting Storage Rings. In 1986 they were used for the PS 201 experiment (Obelix Experiment) at LEAR, the Low Energy Antiproton Ring. The group of researchers from Turin, using the chambers at that time, changed the acquisition system using for the first time 8 bit (10 bit non linear) analog to digital conversion for incoming signals from the chambers. The acquisition system was controlled by 54 CPU and 80 digital signal processors. The power required for all the electronics was 40 kW. For the period, this system was one of the most powerful on-line apparatus in the world. The Obelix Experiment was closed in 1996. To find more about how a wire chamber works, see the description for object CERN-OBJ-DE-038.

  13. Method for Cleaning Laser-Drilled Holes on Printed Wiring Boards by Plasma Treatment

    Science.gov (United States)

    Hirogaki, Toshiki; Aoyama, Eiichi; Minagi, Ryu; Ogawa, Keiji; Katayama, Tsutao; Matsuoka, Takashi; Inoue, Hisahiro

    We propose a new method for cleaning blind via holes after laser drilling of PWBs using oxygen plasma treatment. This report dealt with three kinds of PWB materials: epoxy resin and two kinds of aramid fiber reinforced plastics (AFRP: Technora or Kevlar fiber reinforcement). We observed the drilled holes after plasma treatment using both an optical and a scanning electric microscope (SEM). It was confirmed that adequate etching took place in the drilled holes by plasma treatment. We also compared the hole wall and hole bottom after plasma treatment with ones after chemical etching. It was clear that there was no damage to the aramid fiber tip on the hole wall, and that a smooth roughness of the hole wall was obtained by means of plasma treatment. As a result, we demonstrated that the plasma treatment is effective in cleaning the laser drilled holes of PWBs.

  14. Plasmonic Colour Filters Based on Coaxial Holes in Aluminium

    Directory of Open Access Journals (Sweden)

    Ranjith Rajasekharan Unnithan

    2017-04-01

    Full Text Available Aluminum is an alternative plasmonic material in the visible regions of the spectrum due to its attractive properties such as low cost, high natural abundance, ease of processing, and complementary metal-oxide-semiconductor (CMOS and liquid crystal display (LCD compatibility. Here, we present plasmonic colour filters based on coaxial holes in aluminium that operate in the visible range. Using both computational and experimental methods, fine-tuning of resonance peaks through precise geometric control of the coaxial holes is demonstrated. These results will lay the basis for the development of filters in high-resolution liquid crystal displays, RGB-spatial light modulators, liquid crystal over silicon devices and novel displays.

  15. High-impedance wire grid method to study spatiotemporal behavior of hot electron clump generated in a plasma.

    Science.gov (United States)

    Terasaka, K; Yoshimura, S; Kato, Y; Furuta, K; Aramaki, M; Morisaki, T; Tanaka, M Y

    2014-11-01

    High-impedance Wire Grid (HIWG) detector has been developed to study spatiotemporal behavior of a hot electron clump generated in an electron cyclotron resonance (ECR) plasma. By measuring the floating potentials of the wire electrodes, and generating structure matrix made of geometrical means of the floating potentials, the HIWG detector reconstructs the spatial distribution of high-temperature electron clump at an arbitrary instant of time. Time slices of the spike event in floating potential revealed the growth and decay process of a hot spot occurs in an ECR plasma.

  16. Different mechanical properties in Seldinger guide wires

    Directory of Open Access Journals (Sweden)

    Wolfram Schummer

    2015-01-01

    Full Text Available Background and Aims: Most central venous catheters are placed using Seldinger guide wires. EN ISO 11070 is the guideline for testing guide wire flexing performance and tensile strength, and we can safely assume that guide wires in use meet these requirements. Unfortunately, EN ISO 11070 guidelines do not reflect the clinical requirements and we continue to see mechanical failures and their associated complications. Material and Methods: This in vitro study was performed in an accredited laboratory. With regard to flexing, we: (1 Established the minimum flexing performance needed to meet clinical requirements, (2 developed flexing performance tests which mimic clinical requirement, and (3 evaluated the mechanical properties of various guide wires relative to these requirements. With regard to tensile strength, we used the testing method prescribed in ISO 11070, but did not end the test at 5 Newton (N. We continued until the guide wire was damaged, or we reached maximum tractive force. We then did a wire-to-wire comparison. We examined two basic wire constructions, monofil and core and coil. Results: Tensile strength: All wires tested, except one, met EN ISO 11070 requirements for 5 N tensile strength. The mean of the wire types tested ranged from 15.06 N to 257.76 N. Flexing performance: None of the wires kinked. The monofil had no evidence of bending. Two core/coil wires displayed minor bending (angle 1.5°. All other wires displayed bending angles between 22.5° and 43.0°. Conclusion: We recommend that: (1 Clinicians use guide wires with high-end mechanical properties, (2 EN ISO 11070 incorporate our flexing test into their testing method, raise the flexing requirement to kink-proof, (3 and raise the tensile strength requirement to a minimum of 30 N, and (3 all manufacturers and suppliers be required to display mechanical properties of all guide wire, and guide wire kits sold.

  17. Fabrication and Characterisation of Flexible Coaxial Thin Thread Supercapacitors

    Directory of Open Access Journals (Sweden)

    Fulian Qiu

    2014-08-01

    Full Text Available Flexible coaxial thin thread supercapacitors were fabricated semi-automatically using a dip coating method. A typical coaxial thin thread supercapacitor of a length of 70 cm demonstrated a specific length capacitance of 0.3 mF cm-1 (11.2 mF cm-2 and 2.18 F cm-3 at 5 mV s-1, the device exhibited good electrochemical performance with a high volume energy density of 0.22 mWh cm-3 at a power density of 22 mW cm-3. Thread supercapacitors were assembled in series and parallel combinations, the accepted models for series and parallel circuit combinations were obeyed for two coaxial thread supercapacitors. The thread shows high flexibility and uniformity of specific length capacitance, one integrated with a commercial solar cell could be charged and power a LED. The process is simple, robust and easy to scale up to make unlimited length thread supercapacitors for numerous miniaturized and flexible electronic applications.

  18. Analysis of axially symmetric wire antennas by the use of exact kernel of electric field integral equation

    Directory of Open Access Journals (Sweden)

    Krneta Aleksandra J.

    2016-01-01

    Full Text Available The paper presents a new method for the analysis of wire antennas with axial symmetry. Truncated cones have been applied to precisely model antenna geometry, while the exact kernel of the electric field integral equation has been used for computation. Accuracy and efficiency of the method has been further increased by the use of higher order basis functions for current expansion, and by selecting integration methods based on singularity cancelation techniques for the calculation of potential and impedance integrals. The method has been applied to the analysis of a typical dipole antenna, thick dipole antenna and a coaxial line. The obtained results verify the high accuracy of the method. [Projekat Ministarstva nauke Republike Srbije, br. TR-32005

  19. Ga N nano wires and nano tubes growth by chemical vapor deposition method at different NH{sub 3} flow rate

    Energy Technology Data Exchange (ETDEWEB)

    Li, P.; Liu, Y.; Meng, X. [Wuhan University, School of Physics and Technology, Key Laboratory of Artificial Micro and Nanostructures of Ministry of Education, Wuhan 430072 (China)

    2016-11-01

    Ga N nano wires and nano tubes have been successfully synthesized via the simple chemical vapor deposition method. NH{sub 3} flow rate was found to be a crucial factor in the synthesis of different type of Ga N which affects the shape and the diameter of generated Ga N nano structures. X-ray diffraction confirms that Ga N nano wires grown on Si(111) substrate under 900 degrees Celsius and with NH{sub 3} flow rate of 50 sc cm presents the preferred orientation growth in the (002) direction. It is beneficial to the growth of nano structure through catalyst annealing. Transmission electron microscopy and scanning electron microscopy were used to measure the size and structures of the samples. (Author)

  20. A New Method of Lead Compensation for Three - Wire Resistance Temperature Detectors%热电阻测温仪导线电阻补偿新方法

    Institute of Scientific and Technical Information of China (English)

    李挺; 朱金刚; 赵良煦

    2001-01-01

    提出了一种用于三线制接法热电阻测温仪导线电阻补偿新方法。在传统的热电阻测温仪的不平衡电桥三线制接法中,连接导线电阻(哪怕仅有1Ω)将对测量结果产生约l%的误差。本文在分析了传统的热电阻测温仪不足的基础上,提出了一种新的导线电阻补偿方法,连接导线即使有较大的导线电阻,测量误差将低于0.1%。实验证明该方法是有效的。%An improved lead resistance compensation technique for use with three- wire resistance temperature detectors is presented. The practice of using the three-wire concept in anun-balanced bridge produces nearly 1% error for a lead resistance as low as 1Ω in the conventional resistance temperature detectors. Based on the analysis of drawback of conventional resistance temperature detectors, the paper proposes a new method of lead compensation, which limits the error to below 0. 1% with much higher lead wire resistances. Experiment result verifies the effectiveness of the new method.

  1. Modeling of Coaxial Slot Waveguides Using Analytical and Numerical Approaches: Revisited

    Directory of Open Access Journals (Sweden)

    Kok Yeow You

    2012-01-01

    Full Text Available Our reviews of analytical methods and numerical methods for coaxial slot waveguides are presented. The theories, background, and physical principles related to frequency-domain electromagnetic equations for coaxial waveguides are reassessed. Comparisons of the accuracies of various types of admittance and impedance equations and numerical simulations are made, and the fringing field at the aperture sensor, which is represented by the lumped capacitance circuit, is evaluated. The accuracy and limitations of the analytical equations are explained in detail. The reasons for the replacement of analytical methods by numerical methods are outlined.

  2. Coaxial Cables for Martian Extreme Temperature Environments

    Science.gov (United States)

    Ramesham, Rajeshuni; Harvey, Wayne L.; Valas, Sam; Tsai, Michael C.

    2011-01-01

    Work was conducted to validate the use of the rover external flexible coaxial cabling for space under the extreme environments to be encountered during the Mars Science Laboratory (MSL) mission. The antennas must survive all ground operations plus the nominal 670-Martian-day mission that includes summer and winter seasons of the Mars environment. Successful development of processes established coaxial cable hardware fatigue limits, which were well beyond the expected in-flight exposures. In keeping with traditional qualification philosophy, this was accomplished by subjecting flight-representative coaxial cables to temperature cycling of the same depth as expected in-flight, but for three times the expected number of in-flight thermal cycles. Insertion loss and return loss tests were performed on the coaxial cables during the thermal chamber breaks. A vector network analyzer was calibrated and operated over the operational frequency range 7.145 to 8.450 GHz. Even though some of the exposed cables function only at UHF frequencies (approximately 400 MHz), the testing was more sensitive, and extending the test range down to 400 MHz would have cost frequency resolution. The Gore flexible coaxial cables, which were the subject of these tests, proved to be robust and displayed no sign of degradation due to the 3X exposure to the punishing Mars surface operations cycles.

  3. Turbulence and heat excited noise sources in single and coaxial jets

    Science.gov (United States)

    Koh, Seong Ryong; Schröder, Wolfgang; Meinke, Matthias

    2010-03-01

    The generation of noise in subsonic high Reynolds number single and coaxial turbulent jets is analyzed by a hybrid method. The computational approach is based on large-eddy simulations (LES) and solutions of the acoustic perturbation equations (APE). The method is used to investigate the acoustic fields of one isothermal single stream jet at a Mach number 0.9 and a Reynolds number 400,000 based on the nozzle diameter and two coaxial jets whose Mach number and Reynolds number based on the secondary jet match the values of the single jet. One coaxial jet configuration possesses a cold primary flow, whereas the other configuration has a hot primary jet. Thus, the configurations allow in a first step the analysis of the relationship of the flow and acoustic fields of a single and a cold coaxial jet and in a second step the investigation of the differences of the fluid mechanics and aeroacoustics of cold and hot coaxial jets. For the isothermal single jet the present hybrid acoustic computation shows convincing agreement with the direct acoustic simulation based on large-eddy simulations. The analysis of the acoustic field of the coaxial jets focuses on two noise sources, the Lamb vector fluctuations and the entropy sources of the APE equations. The power spectral density (PSD) distributions evidence the Lamb vector fluctuations to represent the major acoustic sources of the isothermal jet. Especially the typical downstream and sideline acoustic generations occur on a cone-like surface being wrapped around the end of the potential core. Furthermore, when the coaxial jet possesses a hot primary jet, the acoustic core being characterized by the entropy source terms increases the low frequency acoustics by up to 5 dB, i.e., the sideline acoustics is enhanced by the pronounced temperature gradient.

  4. Clinical bending of nickel titanium wires

    Directory of Open Access Journals (Sweden)

    Stephen Chain

    2015-01-01

    Full Text Available Since the evolution and the involvement of Nickel Titanium wires in the field of Orthodontics. The treatment plan has evolved with the use of low force Nickel Titanium wires. Because of their high springback, low stiffness, they are the key initial wires in leveling and alignment but have poor formability. Since poor formability limits its ability to create variable arch forms thus; limits the form of treatment. We have devised a method to bend the Nickel Titanium wires to help in our inventory but also customized the wire according to the treatment.

  5. Prediction of eigenmodes cutoff frequencies of sectoral coaxial ridged waveguides

    OpenAIRE

    2012-01-01

    A mathematical model of sectoral coaxial ridged waveguides has been developed using coupled-integralequations technique. Maximal ratios of cutoff frequencies of two lowest modes of sectoral coaxial ridged waveguides have been obtained.

  6. Detection system of fuel quantity based on coaxial transmission line phase method%基于同轴线式相位法的油量检测系统

    Institute of Scientific and Technical Information of China (English)

    王金华; 尤丽华; 安伟; 吴静静; 林晖

    2016-01-01

    The accuracy of injection quantity directly affects the combustion of fuel. Reliable injection quantity detection method can guarantee the accuracy of the fuel injector and reduce the polluting gases of vehicle exhaust emissions. In order to realize the detection of fuel quantity , converted the detection of fuel quantity to the height detection of fuel level, use a coaxial line sensor to measure the single fuel injection quantity and design a new type of fuel injection quantity detection method. Design a human-computer interaction interface with Delphi that can display the status of the detection system and the data clearly. The single-chip, with Freescale MC9S08AC60 as the core, has function as data acquisition and transmission. This design fully meets the requirements on stability, detection accuracy and responsiveness.%喷油器的喷油精度直接影响燃油的燃烧效果,可靠的喷油量检测方法可以保证喷油器的喷油精度,减少汽车尾气中污染气体的排放。为了实现喷油量的检测,将油量的检测转换为燃油液位的高度检测,使用同轴线式传感器对燃油液面高度进行测量,设计了一种新型的油量检测方法。使用Delphi设计了人机交互界面,清晰显示检测系统的状态与数据;下位机以MC9S08AC60芯片为核心,实现了数据采集与传输。该设计在稳定性、检测精度与响应性上达到了设计要求。

  7. A defect detection method for MgB2 superconducting and iron-based Ba(Fe,Co)2As2 wires

    Science.gov (United States)

    Gajda, D.; Morawski, A.; Zaleski, A.; Yamamoto, A.; Cetner, T.

    2016-04-01

    In this article, a method allowing for the detection of damage in iron-based superconducting bulks and MgB2 wires is presented. MgB2 wires were made of in situ material with ex situ MgB2 barrier. The iron superconductor studied was Ba(Fe,Co)2As2. This material was surrounded by Nb barrier and placed inside an iron tube. All samples were annealed in the isostatic pressure of 1 GPa. Transport measurements were made using a four-contact probe. The transition of Nb and ex situ MgB2 barrier from superconducting into resistive state (first transition) was observed at a temperature range from 5 K to 10 K and can be attributed to damage in either the Nb or ex situ MgB2 barrier in these samples. For samples with a damaged barrier, it was not possible to determine the critical current density of the wires. The analysis indicates that annealing at 1 GPa leads to the Ba(Fe,Co)2As2 material with critical temperatures of 27 K and 21.5 K at upper critical flux density (Bc2) of 14 T.

  8. Fabrication and application of mesoporous TiO2 film coated on Al wire by sol-gel method with EISA

    Science.gov (United States)

    Zhao, Linkang; Lu, Jianjun

    2017-04-01

    Mesoporous TiO2 film on Al wire was fabricated by sol-gel method with evaporation induced self assembly (EISA) process using F127 as templating agent in the mixed solution of ethanol and Tetra-n-butyl Titanate. The Ni/TiO2 film catalyst supported on Al wire was prepared by impregnation and the catalytic performance on methanation was carried out in a titanium alloy micro-reactor tube. It was shown that anatase mesoporous TiO2 film was prepared in this conditions (1 g F127,calcined at 400 °C and aged for 24 h), which has specific surface area of 127 m2 g-1 and narrow pore size distribution of 5.3 nm. Low calcined temperature (300 °C) cannot transfer film to anatase and decompose F127 completely. Ni/TiO2 film on Al wire catalyst was proved to be active in CO methanation reaction. And the CO conversion reaches 99% and CH4 selectivity close is to 80% when the reaction temperature is higher 360 °C.

  9. Coaxial plasma thrusters for high specific impulse propulsion

    Science.gov (United States)

    Schoenberg, Kurt F.; Gerwin, Richard A.; Barnes, Cris W.; Henins, Ivars; Mayo, Robert; Moses, Ronald, Jr.; Scarberry, Richard; Wurden, Glen

    1991-01-01

    A fundamental basis for coaxial plasma thruster performance is presented and the steady-state, ideal MHD properties of a coaxial thruster using an annular magnetic nozzle are discussed. Formulas for power usage, thrust, mass flow rate, and specific impulse are acquired and employed to assess thruster performance. The performance estimates are compared with the observed properties of an unoptimized coaxial plasma gun. These comparisons support the hypothesis that ideal MHD has an important role in coaxial plasma thruster dynamics.

  10. HYBRID MM/MoL APPROACH FOR ANALYZING A COAXIAL FED MONOPOLE ANTENNA

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A new hybrid technique is presented, which combines the Mode Matching(MM) method with the Method of Lines (MoL) to analyze a coaxial fed monopole antenna.The monopole antenna is dealt with using the MoL, while the MM method is used to analyze the coaxial feed system.Then, the two sub-problems are combined by enforcing point matching at the common regional interfaces.The input impedance is computed and compared with the measured data reported in literature, and the excellent agreement is observed.

  11. HYBRID MM/MoL APPROACH FOR ANALYZING A COAXIAL FED MONOPOLE ANTENNA

    Institute of Scientific and Technical Information of China (English)

    Sun Baohua; Ji Yicai; Liu Qizhong

    2002-01-01

    A new hybrid technique is presented, which combines the Mode Matching (MM) method with the Method of Lines (MoL) to analyze a coaxial fed monopole antenna. The monopole antenna is dealt with using the MoL, while the MM method is used to analyze the coaxial feed system. Then, the two sub-problems are combined by enforcing point matching at the common regional interfaces. The input impedance is computed and compared with the measured data reported in literature, and the excellent agreement is observed.

  12. Pneumothorax Complicating Coaxial and Non-coaxial CT-Guided Lung Biopsy: Comparative Analysis of Determining Risk Factors and Management of Pneumothorax in a Retrospective Review of 650 Patients

    Energy Technology Data Exchange (ETDEWEB)

    Nour-Eldin, Nour-Eldin A., E-mail: nour410@hotmail.com; Alsubhi, Mohammed, E-mail: mohammedal-subhi@yahoo.com; Emam, Ahmed, E-mail: morgan101002@hotmail.com; Lehnert, Thomas, E-mail: thomas.lehnert@kgu.de; Beeres, Martin, E-mail: beeres@gmx.net; Jacobi, Volkmar, E-mail: volkmar.jacobi@kgu.de; Gruber-Rouh, Tatjana, E-mail: tatjanagruber2004@yahoo.com; Scholtz, Jan-Erik, E-mail: janerikscholtz@gmail.com; Vogl, Thomas J., E-mail: t.vogl@em.uni-frankfurt.de; Naguib, Nagy N., E-mail: nagynnn@yahoo.com [Johan Wolfgang Goethe – University Hospital, Institute for Diagnostic and Interventional Radiology (Germany)

    2016-02-15

    PurposeTo assess the scope and determining risk factors related to the development of pneumothorax throughout CT-guided biopsy of pulmonary lesions in coaxial and non-coaxial techniques and the outcome of its management.Materials and MethodsThe study included CT-guided percutaneous lung biopsies in 650 consecutive patients (407 males, 243 females; mean age 54.6 years, SD 5.2) from November 2008 to June 2013 in a retrospective design. Patients were classified according to lung biopsy technique into coaxial group (318 lesions) and non-coaxial group (332 lesions). Exclusion criteria for biopsy were lesions <5 mm in diameter, uncorrectable coagulopathy, positive-pressure ventilation, severe respiratory compromise, pulmonary arterial hypertension, or refusal of the procedure. Risk factors related to the occurrence of pneumothorax were classified into: (a) Technical risk factors, (b) patient-related risk factors, and (c) lesion-associated risk factors. Radiological assessments were performed by two radiologists in consensus. Mann–Whitney U test and Fisher’s exact tests were used for statistical analysis. p values <0.05 were considered statistically significant.ResultsThe incidence of pneumothorax complicating CT-guided lung biopsy was less in the non-coaxial group (23.2 %, 77 out of 332) than the coaxial group (27 %, 86 out of 318). However, the difference in incidence between both groups was statistically insignificant (p = 0.14). Significant risk factors for the development of pneumothorax in both groups were emphysema (p < 0.001 in both groups), traversing a fissure with the biopsy needle (p value 0.005 in non-coaxial group and 0.001 in coaxial group), small lesion, less than 2 cm in diameter (p value of 0.02 in both groups), location of the lesion in the basal or mid sections of the lung (p = 0.003 and <0.001 in non-coaxial and coaxial groups, respectively), and increased needle track path within the lung tissue of more than 2.5 cm (p = 0.01 in both

  13. Wire ropes tension, endurance, reliability

    CERN Document Server

    Feyrer, Klaus

    2015-01-01

    The main goal of this book is to present the methods used to calculate the most important parameters for ropes, and to explain how they are applied on the basis of numerous sample calculations. The book, based on the most important chapters of the German book DRAHTSEILE, has been updated to reflect the latest developments, with the new edition especially focusing on computational methods for wire ropes. Many new calculations and examples have also been added to facilitate the dimensioning and calculation of mechanical characteristics of wire ropes. This book offers a valuable resource for all those working with wire ropes, including construction engineers, operators and supervisors of machines and installations involving wire ropes.

  14. Coaxial combination of coherent laser beams

    Institute of Scientific and Technical Information of China (English)

    Hongcheng Dong; Xiao Li; Chaoyang Wei; Hongbo He; Yuanan Zhao; Jianda Shao; Zhengxiu Fan

    2009-01-01

    @@ Based on polarization state conversion, a technique for coaxially coherent combination of laser beams is introduced.Laser beams can be coaxially coupled into one beam with high combination efficiency and perfect beam quality.A polarized laser beam combination system based on master oscillator power amplifier (MOPA) configuration is developed and the efficiencies of both unit combination and the whole system are investigated.In the experiment of combining four beams with single longitudinal mode, a combination efficiency of 85.3% is achieved.It can be further enhanced by improving the stability of experimental environment and the quality of optical and mechanical components.

  15. Preparation and characterization of multi-layer biodegradable nanofibers by coaxial electrospinning and their potential for tissue engineering

    Science.gov (United States)

    Liu, Wenwen

    As an evolution of conventional electrospinning, coaxial electrospinning became popular soon after its debut as a novel way to develop nanofibers with special structures, such as core-shell and hollow interior. In recent years, there has been an increasing interest in a modified coaxial electrospinning, tri-layer coaxial electrospinning, to develop more complex structures, such as multi-layer and nanowire-in-microtube. Previous studies have primarily concentrated on the fabrication of tri-layered inorganic fibers while studies on tri-layered coaxial polymeric fibers has not been reported until very recently. Our research focuses on the fabrication of core-shell and tri-layer structured biodegradable polymeric nanofibers with coaxial electrospinning. Different characterization methods have been applied to observe the internal structure in single nanofibers and the potential application of tri-layer coaxial electrospinning has been discussed. The material system consists of biodegradable natural polymer gelatin, synthetic polymers poly (epsilon-caprolactone) (PCL) and poly (lactic-co-glycolic acid) (PLGA). A uniquely designed three-needle concentric spinneret is developed to perform tri-layer coaxial electrospinning. Different kinds of core-shell structured nanofibers, including gelatin/PCL, PCL/gelatin, gelatin/PLGA and PCL/PLGA, have been fabricated with a customized coaxial electrospinning apparatus. Two kinds of tri-layer coaxial nanofibers, two-component ABA structured gelatin/PCL/gelatin biodegradable nanofibers and tri-component ABC structured gelatin/PCL/PLGA biodegradable nanofibers, have been developed with the customized three needle coaxial electrospinning setup. The core-shell and tri-layered structures of electrospun nanofibers have been characterized by several commonly used techniques, such as laser scanning confocal microscopy (LSCM) and transmission electron microscopy (TEM). Besides the conventional methods, other newer techniques, including

  16. Experiments on the formation of a recirculation zone in swirling coaxial jets

    Science.gov (United States)

    Champagne, F. H.; Kromat, S.

    The near flow field of coaxial air jets, with swirl in the outer one, was studied using flow visualization and hot-wire anemometry. The flow is sensitive to both the swirl number and the mass flow ratio between the outer and inner jets. A necessary condition for the formation of an internal recirculation zone (IRZ) is that the swirl number must exceed a minimum value which depends on the mass flow ratio. Spectral analysis of the velocity fluctuations indicates that the formation of an IRZ in the present flow does not appear to be related to the growth of convective flow instabilities. Analysis of the flow visualization and X-wire data indicates that the vorticity dynamics model for vortex breakdown proposed by Brown and Lopez [J Fluid Mech (1990) 222: 553] provides a plausible mechanism for the formation of an IRZ in this flow.

  17. 30 CFR 75.1003 - Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley...

    Science.gov (United States)

    2010-07-01

    ... wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 75.1003 Section 75.1003... Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley wires and trolley feeder wires. Trolley wires, trolley feeder wires, and bare signal wires shall be insulated...

  18. A Survey of Theoretical and Experimental Coaxial Rotor Aerodynamic Research

    Science.gov (United States)

    Coleman, Colin P.

    1997-01-01

    The recent appearance of the Kamov Ka-50 helicopter and the application of coaxial rotors to unmanned aerial vehicles have renewed international interest in the coaxial rotor configuration. This report addresses the aerodynamic issues peculiar to coaxial rotors by surveying American, Russian, Japanese, British, and German research. (Herein, 'coaxial rotors' refers to helicopter, not propeller, rotors. The intermeshing rotor system was not investigated.) Issues addressed are separation distance, load sharing between rotors, wake structure, solidity effects, swirl recovery, and the effects of having no tail rotor. A general summary of the coaxial rotor configuration explores the configuration's advantages and applications.

  19. Hydromagnetic Flow between Two Rotating Coaxial Discs

    Directory of Open Access Journals (Sweden)

    Abdul Aleem Khan

    1970-01-01

    Full Text Available This paper relates to the steady flow of an electrically incompressible viscous fluid between two parallel coaxial rotating discs with a transverse magnetic field when the discs are rotating in the same direction with the same velocity and there is a source at the centre.

  20. Triple mode filters with coaxial excitation

    NARCIS (Netherlands)

    Gerini, G.; Bustamante, F.D.; Guglielmi, M.

    2004-01-01

    In this paper we describe triple mode filters in a square waveguide with integrated coaxial input/output excitation. An important feature of the structure proposed is that it is easily amenable to an accurate full wave analysis. In addition to theory, a practical six pole filter with two transmissio

  1. Analysis of coaxial laser cladding processing conditions

    NARCIS (Netherlands)

    de Oliveira, U; Ocelik, V; De Hosson, JTM

    2005-01-01

    The formation of thick Ni-based coating on a steel substrate by coaxial laser cladding using the Nd:YAG 2 kW continuous laser was studied both from a theoretical and experimental point of view. The theoretical analysis concentrated on the transfer of laser irradiation and powder particles using a si

  2. The heterogeneous electrochemical characteristics of mild steel in the presence of local glucose oxidase-A study by the wire beam electrode method

    Energy Technology Data Exchange (ETDEWEB)

    Wang Wei [Key Laboratory of Marine Chemistry Theory and Technology, Ministry of Education, Ocean University of China, College of Chemistry and Chemical Engineering, Qingdao 266100 (China)], E-mail: wwei@ouc.edu.cn; Lu Yonghong; Zou Yan; Zhang Xia [Key Laboratory of Marine Chemistry Theory and Technology, Ministry of Education, Ocean University of China, College of Chemistry and Chemical Engineering, Qingdao 266100 (China); Wang Jia [Key Laboratory of Marine Chemistry Theory and Technology, Ministry of Education, Ocean University of China, College of Chemistry and Chemical Engineering, Qingdao 266100 (China); State Key Laboratory for Corrosion and Protection, Shenyang 110016 (China)

    2010-03-15

    The influence of glucose oxidase (GOD) activity on the heterogeneous electrochemistry at artificial biofilm/mild steel interface was first characterized by the wire beam electrode (WBE) method. Potential/current distribution maps show that a cathodic zone can be formed at the GOD capsule site. The cathodic zone is gradually weakened due to the gluconic acid production in seawater. When GOD capsule is confined on rusted WBE surfaces, the formerly formed anodic zone is gradually changed into cathodic zone, in the presence of glucose. The novel device developed in our laboratory demonstrates powerful applications in heterogeneous electrochemistry measurements at the biofilm/mild steel interfaces.

  3. Vibrating wires for beam diagnostics

    CERN Document Server

    Arutunian, S G; Wittenburg, Kay

    2015-01-01

    A new approach to the technique of scanning by wires is developed. Novelty of the method is that the wire heating quantity is used as a source of information about the number of interacting particles. To increase the accuracy and sensitivity of measurements the wire heating measurement is regenerated as a change of wire natural oscillations frequency. By the rigid fixing of the wire ends on the base an unprecedented sensitivity of the frequency to the temperature and to the corresponding flux of colliding particles. The range of used frequencies (tens of kHz) and speed of processes of heat transfer limit the speed characteristics of proposed scanning method, however, the high sensitivity make it a perspective one for investigation of beam halo and weak beam scanning. Traditional beam profile monitors generally focus on the beam core and loose sensitivity in the halo region where a large dynamic range of detection is necessary. The scanning by a vibrating wire can be also successfully used in profiling and det...

  4. A method for rapid sampling and characterization of smokeless powder using sorbent-coated wire mesh and direct analysis in real time - mass spectrometry (DART-MS).

    Science.gov (United States)

    Li, Frederick; Tice, Joseph; Musselman, Brian D; Hall, Adam B

    2016-09-01

    Improvised explosive devices (IEDs) are often used by terrorists and criminals to create public panic and destruction, necessitating rapid investigative information. However, backlogs in many forensic laboratories resulting in part from time-consuming GC-MS and LC-MS techniques prevent prompt analytical information. Direct analysis in real time - mass spectrometry (DART-MS) is a promising analytical technique that can address this challenge in the forensic science community by permitting rapid trace analysis of energetic materials. Therefore, we have designed a qualitative analytical approach that utilizes novel sorbent-coated wire mesh and dynamic headspace concentration to permit the generation of information rich chemical attribute signatures (CAS) for trace energetic materials in smokeless powder with DART-MS. Sorbent-coated wire mesh improves the overall efficiency of capturing trace energetic materials in comparison to swabbing or vacuuming. Hodgdon Lil' Gun smokeless powder was used to optimize the dynamic headspace parameters. This method was compared to traditional GC-MS methods and validated using the NIST RM 8107 smokeless powder reference standard. Additives and energetic materials, notably nitroglycerin, were rapidly and efficiently captured by the Carbopack X wire mesh, followed by detection and identification using DART-MS. This approach has demonstrated the capability of generating comparable results with significantly reduced analysis time in comparison to GC-MS. All targeted components that can be detected by GC-MS were detected by DART-MS in less than a minute. Furthermore, DART-MS offers the advantage of detecting targeted analytes that are not amenable to GC-MS. The speed and efficiency associated with both the sample collection technique and DART-MS demonstrate an attractive and viable potential alternative to conventional techniques.

  5. Simplified Transient Hot-Wire Method for Effective Thermal Conductivity Measurement in Geo Materials: Microstructure and Saturation Effect

    Directory of Open Access Journals (Sweden)

    B. Merckx

    2012-01-01

    Full Text Available The thermal conductivity measurement by a simplified transient hot-wire technique is applied to geomaterials in order to show the relationships which can exist between effective thermal conductivity, texture, and moisture of the materials. After a validation of the used “one hot-wire” technique in water, toluene, and glass-bead assemblages, the investigations were performed (1 in glass-bead assemblages of different diameters in dried, water, and acetone-saturated states in order to observe the role of grain sizes and saturation on the effective thermal conductivity, (2 in a compacted earth brick at different moisture states, and (3 in a lime-hemp concrete during 110 days following its manufacture. The lime-hemp concrete allows the measurements during the setting, desiccation and carbonation steps. The recorded Δ/ln( diagrams allow the calculation of one effective thermal conductivity in the continuous and homogeneous fluids and two effective thermal conductivities in the heterogeneous solids. The first one measured in the short time acquisitions (<1 s mainly depends on the contact between the wire and grains and thus microtexture and hydrated state of the material. The second one, measured for longer time acquisitions, characterizes the mean effective thermal conductivity of the material.

  6. Discussion on the Quality Traceability Management of Wire and Cable Products%电线电缆产品质量追溯管理的探讨

    Institute of Scientific and Technical Information of China (English)

    高旭阳; 王东洋

    2011-01-01

    电线电缆的质量管理必须贯串整个生产过程。虽然质量追溯管理不能直接对电线电缆产品质量有促进作用,但是它能在跟踪产品生产过程、质量控制等领域发挥着重要的作用。结合电线电缆生产的特点,提出了电线电缆产品质量追溯的方法和形式,并以具体同轴电缆质量追溯管理为例,为其他企业建立质量追溯管理提供了参考。%The quality control of wires and cables must run through the whole production process. Although quality traceability management can not directly promote the product quality of wires and cables, it cao play very important role in the fields of tracing product's production and quality control. Combining with the features of wire and cable production the tracing methods and forms for wire and cable quality are proposed, and the quality traceability management of coaxial cable is taken as the example for other enterprises' reference in establishing quality traceability management.

  7. Analysis and Design Optimization of a Coaxial Surface-Mounted Permanent-Magnet Magnetic Gear

    DEFF Research Database (Denmark)

    Zhang, Xiaoxu; Liu, Xiao; Wang, Chao

    2014-01-01

    This paper presents the analysis and design optimization of a coaxial surface-mounted permanent-magnet magnetic gear. The magnetic field distribution in the coaxial magnetic gear is calculated analytically in the polar coordinate system and then validated by the finite element method (FEM......) algorithm is employed to optimize the studied magnetic gear. Given that the torque capability and material cost conflict with each other, both of them are set as the optimization objectives in this paper. Different weight factors may be chosen for the two objectives so that more attention can be placed...

  8. Turbulence coefficients and stability studies for the coaxial flow or dissimiliar fluids. [gaseous core nuclear reactors

    Science.gov (United States)

    Weinstein, H.; Lavan, Z.

    1975-01-01

    Analytical investigations of fluid dynamics problems of relevance to the gaseous core nuclear reactor program are presented. The vortex type flow which appears in the nuclear light bulb concept is analyzed along with the fluid flow in the fuel inlet region for the coaxial flow gaseous core nuclear reactor concept. The development of numerical methods for the solution of the Navier-Stokes equations for appropriate geometries is extended to the case of rotating flows and almost completes the gas core program requirements in this area. The investigations demonstrate that the conceptual design of the coaxial flow reactor needs further development.

  9. Design and experiments for the waveguide to coaxial cable adapter of a cavity beam position monitor

    Institute of Scientific and Technical Information of China (English)

    LI Xiang; ZHENG Shu-Xin

    2011-01-01

    The waveguide to coaxial cable adapter is very important to the cavity beam position monitor(CBPM)because it determines how much of the energy in the cavity could be coupled outside.In this paper,the waveguide to coaxial cable adapter of a CBPM is designed and experiments are conducted.The curve shapes of experiments and simulations are very similar and the difference in reflection is less than 0.1.This progress provides a reliable method for designing the adapter.

  10. Readout fidelity of coaxial holographic digital data page recording in nanoparticle-(thiol-ene) polymer composites

    Science.gov (United States)

    Nagaya, Kohta; Hata, Eiji; Tomita, Yasuo

    2016-09-01

    We report on an experimental investigation of nanoparticle-concentration and thiol-to-ene stoichiometric ratio dependences of symbol error rates (SERs) and signal-to-noise ratios (SNRs) of digital data pages recorded at a wavelength of 532 nm in thiol-ene based nanoparticle-polymer composite (NPC) films by using a coaxial holographic digital data storage method. We show that SERs and SNRs at the optimized material condition can be lower than 1 × 10-4 and higher than 10, respectively, without error correction coding. These results show the usefulness of thiol-ene based NPCs as coaxial holographic data storage media.

  11. Double Fillet Welding of Carbon Steel T-Joint by Double Channel Shielding Gas Metal Arc Welding Method Using Metal Cored Wire

    Directory of Open Access Journals (Sweden)

    Mert T.

    2017-06-01

    Full Text Available Low carbon steel material and T-joints are frequently used in ship building and steel constructions. Advantages such as high deposition rates, high quality and smooth weld metals and easy automation make cored wires preferable in these industries. In this study, low carbon steel materials with web and flange thicknesses of 6 mm, 8 mm and 10 mm were welded with conventional GMAW and double channel shielding gas metal arc welding (DMAG method to form double fillet T-joints using metal cored wire. The difference between these two methods were characterized by measurements of mean welding parameters, Vickers hardness profiles, weld bead and HAZ geometry of the joints and thermal camera temperature measurements. When weld bead and HAZ geometries are focused, it was seen filler metal molten area increased and base metal molten area decreased in DMAG of low carbon steel. When compared with traditional GMAW, finer and acicular structures in weld metal and more homogenous and smaller grains in HAZ are obtained with double channel shielding gas metal arc welding.

  12. Wire frame to MOVIE. BYU transfer program

    Energy Technology Data Exchange (ETDEWEB)

    Robbins, D.; Byers, L.D.; Benner, M.S.

    1982-12-01

    At SNLA, the primary computer-aided drafting tool is the Applicon Graphics System (AGS). The data base for mechanical parts on the AGS is a wire frame model. This report summarizes a method of adding surface information to the wire frame and passing this information up stream to MOVIE.BYU which is on a VAX computer and is used to produce shaded graphics pictures of the AGS wire frame model on a RAMTEK 9400 display terminal.

  13. Nondestructive Evaluation of Aircraft and Spacecraft Wiring

    Science.gov (United States)

    White, John E.; Tucholski, Edward J.; Green, Robert E., Jr.

    2004-01-01

    Spacecraft, and especially aircraft, often fry well past their original design lives and, therefore, the need to develop nondestructive evaluation procedures for inspection of vital structures in these craft is extremely important. One of the more recent problems is the degradation of wiring and wiring insulation. The present paper describes several nondestructive characterization methods which afford the possibility to detect wiring and insulation degradation in-situ prior to major problems with the safety of aircraft and spacecraft.

  14. Contribution of ion beam analysis methods to the development of 2nd generation high temperature superconducting (HTS) wires

    Energy Technology Data Exchange (ETDEWEB)

    Usov, Igor O [Los Alamos National Laboratory; Arendt, Paul N [Los Alamos National Laboratory; Stan, Liliana [Los Alamos National Laboratory; Holesinger, Terry G [Los Alamos National Laboratory; Foltyn, Steven R [Los Alamos National Laboratory; Depaula, Raymond F [Los Alamos National Laboratory

    2009-01-01

    One of the crucial steps in the second generation high temperature superconducting wire program was development of the buffer layer architecture. The architecture designed at the Superconductivity Technology Center at Los Alamos National Laboratory consists of several oxide layers wherein each layer plays a specific role, namely: nucleation layer, diffusion barrier, biaxially textured template, and an intermediate layer with a good match to the lattice parameter of superconducting Y{sub 1}Ba{sub 2}Cu{sub 3}O{sub 7} (YBCO) compound. This report demonstrates how a wide range of ion beam analysis techniques (SIMS, RBS, channeling, PIXE, PIGE, NRA, ERD) was employed for analysis of each buffer layer and the YBCO films. These results assisted in understanding of a variety of physical processes occurring during the buffet layer fabrication and helped to optimize the buffer layer architecture as a whole.

  15. Technological parameter optimization for elastic tube of spinning spindle and the coaxiality controlling method%纺纱锭子弹性管工艺参数优化与同轴度控制方法

    Institute of Scientific and Technical Information of China (English)

    刘向东; 李蓓智; 杨建国

    2011-01-01

    针对高速纺纱锭子弹性管结合件加工时易变形、同轴度精度差等制造工艺瓶颈,采用金属切削有限元分析软件Advant Edge建立了弹性管支撑孔镗削工步的有限元分析模型,考察并揭示了单个工艺参数对切削力和刀具温度的影响规律,发现背吃刀量对切削力的影响最大,切削速度对切削力的影响最小,进给量介于二者之间.而刀具温度将随着切削速度、背吃刀量及进给量的增加而升高.基于以上规律和减少弹性管加工变形、提高加工效率等目标,进行了工艺参数的综合优化设计,即适当减小背吃刀量、增加进给量和切削速度的优化策略.弹性管支撑孔的工艺参数优化设计和同轴度误差综合分析结果表明,根据高速纺纱锭子弹性管结合件的结构参数和精度要求等,合理选择和有效组合工艺参数是改善该类产品制造工艺瓶颈的重要途径之一.%Specific to the bottleneck in manufacturing process such as proteiform and low precision in coaxiality in machining assembly for elastic tube of high-speed spinning spindle,an infinite analysis model for support holes boring phase of the elastic tube is established with metal cutting software Advant Edge in order to explore and reveal the impact of each technological parameter upon cutting forces and machine tool temperature.It is found that back engagement impact the most on cutting forces,cutting velocity the least, while feed is somewhere in-between.However cutting tool temperature increases with the increase of back engagement,feed and cutting velocity.Based on the above comprehensive optimization design fortechnological parameters is conducted in order to reduce deformation of high-speed spinning spindle elastic tube ,improve machining efficiency.That is to say an optimized strategy of increasing feeding and cutting velocity by reducing back engagement is adopted.The results regarding optimization design and error analysis

  16. Determinación del límite de rotura de un cable por Método de los Elementos Finitos. // Determination of resistance load on steel wire rope by Finite Elements Method.

    Directory of Open Access Journals (Sweden)

    F. Aguilar Parés

    2008-09-01

    Full Text Available En ocasiones, se desconocen las características originales de un cable de acero. En estos casos, generalmente se estima ellímite de rotura de un cable a partir del límite de rotura de un alambre del cable. En el presente trabajo, se propone emplearun método para estimar el límite de rotura del cable en base al modelado del cordón mediante elementos finitos. En elcontenido se explica detalladamente el procedimiento y es ejemplificado. El procedimiento es iniciado con el dibujo delcable en un programa de diseño gráfico parámetrico y posteriormente se describen las características generales delmodelado con un programa especializado en el Método de Elementos Finitos. En el análisis se incluye la influencia delcontacto entre los alambres que forman el cordón. Por último, se comparan los resultados obtenidos para el límite de roturadel cable con los datos declarados por el fabricante. Con este procedimiento fueron obtenidos valores mediante modeladodel cable con diferencias entre el 11% al 2,5% en relación al límite de rotura declarado por los fabricantes. Las diferenciasfueron evidenciadas en dependencia de la calidad del mallado empleado.Palabras claves: Cables de acero, elementos finitos, carga límite de rotura._________________________________________________________________________Abstract:In occasions, the original characteristics of steel wire rope are unknown. In these cases, could be estimated the resistanceof the wire rope knowing the wire resistance. In this proposal method for estimating the resistance load of steel wire thecord of the wire rope is modelling using finite elements. Procedure is explained and a sample with a selected wire rope ispresented. It is started with the drawing of the wire rope by professional software. General characteristics of themodelling are described with FEM software. In the analysis, the contact influence in the wires of the cord is included.Lastly, the obtained results of the resistance

  17. Phosphorus in antique iron music wire.

    Science.gov (United States)

    Goodway, M

    1987-05-22

    Harpsichords and other wire-strung musical instruments were made with longer strings about the beginning of the 17th century. This change required stronger music wire. Although these changes coincided with the introduction of the first mass-produced steel (iron alloyed with carbon), carbon was not found in samples of antique iron harpsichord wire. The wire contained an amount of phosphorus sufficient to have impeded its conversion to steel, and may have been drawn from iron rejected for this purpose. The method used to select pig iron for wire drawing ensured the highest possible phosphorus content at a time when its presence in iron was unsuspected. Phosphorus as an alloying element has had the reputation for making steel brittle when worked cold. Nevertheless, in replicating the antique wire, it was found that lowcarbon iron that contained 0.16 percent phosphorus was easily drawn to appropriate gauges and strengths for restringing antique harpsichords.

  18. Analytical Treatment of an Oldroyd 8-constant Fluid Between Coaxial Cylinders with Variable Viscosity

    Institute of Scientific and Technical Information of China (English)

    Muhammad Yousaf Malik; Azad Hussain; Sohail Nadeem

    2011-01-01

    The flow of an Oldroyd 8-constant fluid between coaxial cylinders with variable viscosity is considered. The heat transfer analysis is also taken into account. An analytical solution of the non-linear problem is obtained using homotopy analysis method. The behavior of pertinent parameters is analyzed and depicted through graphs.

  19. Negative refractive index in coaxial plasmon waveguides.

    Science.gov (United States)

    de Waele, René; Burgos, Stanley P; Atwater, Harry A; Polman, Albert

    2010-06-07

    We theoretically show that coaxial waveguides composed of a metallic core, surrounded by a dielectric cylinder and clad by a metal outer layer exhibit negative refractive index modes over a broad spectral range in the visible. For narrow dielectric gaps (10 nm GaP embedded in Ag) a figure-of-merit of 18 can be achieved at lambda(0) = 460 nm. For larger dielectric gaps the negative index spectral range extends well below the surface plasmon resonance frequency. By fine-tuning the coaxial geometry the special case of n = -1 at a figure-of-merit of 5, or n = 0 for a decay length of 500 nm can be achieved.

  20. Liquid atomization by coaxial rocket injectors

    Science.gov (United States)

    Sankar, S. V.; Brena De La Rosa, A.; Isakovic, A.; Bachalo, W. D.

    1991-01-01

    The atomization characteristics of a scaled-down version of a coaxial rocket injector was investigated using a phase Doppler particle analyzer (PDPA). The injector was operated in the conventional mode with liquid being injected through its inner orifice and gas being injected through its outer annulus. The shearing action occurring at the liquid-gas interface causes the liquid jet to atomize. In this study, two different liquid-air systems, namely a water-air system and a liquid nitrogen-gaseous nitrogen system, were chosen for detailed investigation. This paper discusses the performance characteristics of the coaxial injector under different flow and geometric conditions. Specifically, the effects of injection gas pressure and the injector cavity size on variables such as the mean particle diameter, Sauter mean diameter, number density, volume flux, and velocity have been presented.

  1. Detection of Coaxial Backscattered Electrons in SEM

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    We present a coaxial detection of the backscattered electrons in SEM. The lens-aperture has been used to filter in energy and focus the backscattered electrons. This particular geometry allows us to eliminate the iow energy backscattered electrons and collect the backscattered electrons, which are backscattered close to the incident beam orientation. The main advantage of this geometry is adapted to topographic contrast attenuation and atomic number contrast enhancement. Thus this new SEM is very suitable to analyze the material composition.

  2. Coaxial microwave electrothermal thruster performance in hydrogen

    Science.gov (United States)

    Richardson, W.; Asmussen, J.; Hawley, M.

    1994-01-01

    The microwave electro thermal thruster (MET) is an electric propulsion concept that offers the promise of high performance combined with a long lifetime. A unique feature of this electric propulsion concept is its ability to create a microwave plasma discharge separated or floating away from any electrodes or enclosing walls. This allows propellant temperatures that are higher than those in resistojets and reduces electrode and wall erosion. It has been demonstrated that microwave energy is coupled into discharges very efficiently at high input power levels. As a result of these advantages, the MET concept has been identified as a future high power electric propulsion possibility. Recently, two additional improvements have been made to the coaxial MET. The first was concerned with improving the microwave matching. Previous experiments were conducted with 10-30 percent reflected power when incident power was in excess of 600 W(exp 6). Power was reflected back to the generator because the impedance of the MET did not match the 50 ohm impedance of the microwave circuit. To solve this problem, a double stub tuning system has been inserted between the MET and the microwave power supply. The addition of the double stub tuners reduces the reflected power below 1 percent. The other improvement has prepared the coaxial MET for hydrogen experiments. To operate with hydrogen, the vacuum window which separates the coaxial line from the discharge chamber has been changed from teflon to boron nitride. All the microwave energy delivered to the plasma discharge passes through this vacuum window. This material change had caused problems in the past because of the increased microwave reflection coefficients associated with the electrical properties of boron nitride. However, by making the boron nitride window electrically one-half of a wavelength long, power reflection in the window has been eliminated. This technical note summarizes the experimental performance of the improved

  3. Coaxial Propellant Injectors With Faceplate Annulus Control

    Science.gov (United States)

    Horn, Mark D.; Miyata, Shinjiro; Farhangi, Shahram

    2010-01-01

    An improved design concept for coaxial propellant injectors for a rocket engine (or perhaps for a non-rocket combustion chamber) offers advantages of greater robustness, less complexity, fewer parts, lower cost, and less bulk, relative to prior injectors of equivalent functionality. This design concept is particularly well suited to small, tight-tolerance injectors, for which prior designs are not suitable because the practical implementation of those designs entails very high costs and difficulty in adhering to the tolerances.

  4. Shielded Coaxial Optrode Arrays for Neurophysiology.

    Science.gov (United States)

    Naughton, Jeffrey R; Connolly, Timothy; Varela, Juan A; Lundberg, Jaclyn; Burns, Michael J; Chiles, Thomas C; Christianson, John P; Naughton, Michael J

    2016-01-01

    Recent progress in the study of the brain has been greatly facilitated by the development of new tools capable of minimally-invasive, robust coupling to neuronal assemblies. Two prominent examples are the microelectrode array (MEA), which enables electrical signals from large numbers of neurons to be detected and spatiotemporally correlated, and optogenetics, which enables the electrical activity of cells to be controlled with light. In the former case, high spatial density is desirable but, as electrode arrays evolve toward higher density and thus smaller pitch, electrical crosstalk increases. In the latter, finer control over light input is desirable, to enable improved studies of neuroelectronic pathways emanating from specific cell stimulation. Here, we introduce a coaxial electrode architecture that is uniquely suited to address these issues, as it can simultaneously be utilized as an optical waveguide and a shielded electrode in dense arrays. Using optogenetically-transfected cells on a coaxial MEA, we demonstrate the utility of the architecture by recording cellular currents evoked from optical stimulation. We also show the capability for network recording by radiating an area of seven individually-addressed coaxial electrode regions with cultured cells covering a section of the extent.

  5. Coaxial electrospray of microparticles and nanoparticles for biomedical applications.

    Science.gov (United States)

    Zhang, Leilei; Huang, Jiwei; Si, Ting; Xu, Ronald X

    2012-11-01

    Coaxial electrospray is an electrohydrodynamic process that produces multilayer microparticles and nanoparticles by introducing coaxial electrified jets. In comparison with other microencapsulation/nanoencapsulation processes, coaxial electrospray has several potential advantages such as high encapsulation efficiency, effective protection of bioactivity and uniform size distribution. However, process control in coaxial electrospray is challenged by the multiphysical nature of the process and the complex interplay of multiple design, process and material parameters. This paper reviews the previous works and the recent advances in design, modeling and control of a coaxial electrospray process. The review intends to provide general guidance for coaxial electrospray and stimulate further research and development interests in this promising microencapsulation/nanoencapsulation process.

  6. Wire harness twisting aid

    Science.gov (United States)

    Casey, E. J.; Commadore, C. C.; Ingles, M. E.

    1980-01-01

    Long wire bundles twist into uniform spiral harnesses with help of simple apparatus. Wires pass through spacers and through hand-held tool with hole for each wire. Ends are attached to low speed bench motor. As motor turns, operator moves hand tool away forming smooth twists in wires between motor and tool. Technique produces harnesses that generate less radio-frequency interference than do irregularly twisted cables.

  7. Prospective study of treatment of extraarticular fractures of distal end radius by cross K wire fixation and cast immobilisation and its comparison with Kapandji's method of intrafocal pinning anatomically and functionally

    Directory of Open Access Journals (Sweden)

    Paresh Patil

    2015-04-01

    Full Text Available Background: Distal radius fractures account for 17% of all fractures in adults. The fracture of the lower end of radius crushes the mechanical foundation of man's most elegant tool, the hand. No other fracture has a greater potential to devastate hand function. Extra-articular fractures (type A in the AO classification require avoidance of malunion with angulation and shortening. Malalignment results in limitation of movement, changes in load distribution, midcarpal instability and an increased risk of osteoarthritis of the radiocarpal joint. Aims and objectives: Treatment of extraarticular fractures of distal end radius by cross K wire fixation and cast immobilisation and its comparison with Kapandji's method of intrafocal pinning anatomically and functionally. Methods: Total 50 cases were included in the study. First 25 cases were treated by Kapandji's method and next 25 cases were treated by cross K wire fixation and all cases were given below elbow cast after internal fixation. Patients were followed up at regular intervals and Anatomical and functional outcomes were evaluated in all the patients. Results: In our study anatomical end results were satisfactory in 96% and unsatisfactory in 4% of the subjects treated with cross K wire fixation and 72% and 28% in cases treated by Kapandji's method whereas Functional end results were excellent in 28% cases, good in 68% cases, fair in 4% case and poor in 0% cases treated with cross k wire fixation and 12%, 60%, 24% and 4% in cases treated by Kapandji's method. Conclusion: Cross K wire method proved to be better than Kapandji's method of intrafocal K wire fixation both functionally and anatomically. [Int J Res Med Sci 2015; 3(4.000: 883-890

  8. A Study of Coaxial Rotor Performance and Flow Field Characteristics

    Science.gov (United States)

    2016-01-22

    A Study of Coaxial Rotor Performance and Flow Field Characteristics Natasha L. Barbely Aerospace Engineer NASA Ames Research Center Moffett Field...The pressure field generated by the two airfoils aided our interpretation of the more complex coaxial rotor system flow field. The pressure fields...velocity (ft/sec) Z vertical distance between rotors (ft) αS pitch angle (deg), negative pitch down κint coaxial rotor induced power interference

  9. Water Desalination with Wires

    NARCIS (Netherlands)

    Porada, S.; Sales, B.B.; Hamelers, H.V.M.; Biesheuvel, P.M.

    2012-01-01

    We show the significant potential of water desalination using a novel capacitive wire-based technology in which anode/cathode wire pairs are constructed from coating a thin porous carbon electrode layer on top of electrically conducting rods (or wires). By alternately dipping an array of electrode

  10. Measurements of Thermal Conductivity and Thermal Diffusivity of Hen Egg-White Lysozyme Crystals and Its Solution Using the Transient Short Hot Wire Method

    Science.gov (United States)

    Fujiwara, Seiji; Maki, Syou; Maekawa, Ryunosuke; Tanaka, Seiichi; Hagiwara, Masayuki

    2017-08-01

    Protein crystals are an essentially important biological sample to advance the analysis of X-ray structure, but their thermophysical properties, especially thermal conductivity and thermal diffusivity, have not been studied sufficiently. This current situation can be attributed to various kinds of technical problems; e.g., the fragility of protein crystals and the difficulty of nucleation control. Ideally speaking, protein crystallization should be carried out under a " containerless condition" to eliminate any mechanical distortion of the crystals from the walls. To realize the condition, we have developed an original crystallization method by means of the magneto-Archimedes effect. In this paper, a transient short hot wire method was combined with the technique of magneto-Archimedes effect to realize simultaneous measurement of thermal conductivity and thermal diffusivity of hen egg-white lysozyme (HEWL) crystals. As the results, thermal conductivity and thermal diffusivity of HEWL crystals were found to be 0.410-0.438 \\hbox {W}\\cdot \\hbox {m}^{-1}\\cdot \\hbox {K}^{-1} and 3.77-5.18× 10^{-8} \\hbox {m}2\\cdot \\hbox {s}^{-1}, respectively. We clarified by the crystallizing process of HEWL that the crystals were magnetically levitated at the air-liquid interface and the short hot wire was completely buried into them as the crystals grew. We also measured the HEWL solution by the same methods. The thermal conductivity of the solution had almost the same value as that of water and had little dependency on the concentration of HEWL, but the thermal diffusivity was unclear.

  11. Computations of Torque-Balanced Coaxial Rotor Flows

    Science.gov (United States)

    Yoon, Seokkwan; Chan, William M.; Pulliam, Thomas H.

    2017-01-01

    Interactional aerodynamics has been studied for counter-rotating coaxial rotors in hover. The effects of torque balancing on the performance of coaxial-rotor systems have been investigated. The three-dimensional unsteady Navier-Stokes equations are solved on overset grids using high-order accurate schemes, dual-time stepping, and a hybrid turbulence model. Computational results for an experimental model are compared to available data. The results for a coaxial quadcopter vehicle with and without torque balancing are discussed. Understanding interactions in coaxial-rotor flows would help improve the design of next-generation autonomous drones.

  12. Hot-wire anemometer for spirography.

    Science.gov (United States)

    Plakk, P; Liik, P; Kingisepp, P H

    1998-01-01

    The use of a constant temperature hot-wire anemometer flow sensor for spirography is reported. The construction, operating principles and calibration procedure of the apparatus are described, and temperature compensation method is discussed. Frequency response is studied. It is shown that this hot-wire flow transducer satisfies common demands with respect to accuracy, response time and temperature variations.

  13. PS wire chamber

    CERN Multimedia

    1970-01-01

    A wire chamber used at CERN's Proton Synchrotron accelerator in the 1970s. Multi-wire detectors contain layers of positively and negatively charged wires enclosed in a chamber full of gas. A charged particle passing through the chamber knocks negatively charged electrons out of atoms in the gas, leaving behind positive ions. The electrons are pulled towards the positively charged wires. They collide with other atoms on the way, producing an avalanche of electrons and ions. The movement of these electrons and ions induces an electric pulse in the wires which is collected by fast electronics. The size of the pulse is proportional to the energy loss of the original particle.

  14. Numerical-experimental analyses by Hot-Wire method of an alumina cylinder for future studies on thermal conductivity of the fusion breeder materials

    Science.gov (United States)

    Lo Frano, R.; Moscardini, M.; Aquaro, D.

    2014-11-01

    The determination of the thermal conductivity of breeder materials is one of the main goal in order to find the best candidate material for the fusion reactor technology. Experimental tests have been and will be carried out with a dedicated experimental devices, built at the Department of Civil and Industrial Engineering of the University of Pisa. The methodological approach used in doing that is characterized by two main phases strictly interrelated each other: the first one focused on the experimental evaluation of thermal conductivity of a ceramic material, by means of hot wire method, to be subsequently used in the second phase, based on the test rig method, to determine the thermal conductivity of pebble bed material. To the purpose, two different experimental devices have been designed and built. This paper deals with the first phase of the methodology. In this framework, the equipment set up and built to perform Hot wire tests, the ceramic material (a cylinder of alumina), the experimental procedure and the measured results obtained varying the temperature, are presented and discussed. The experimental campaign has been lead from 50°C up to 400°C. The thermal conductivity of the ceramic material at different bulk temperatures has been obtained in stationary conditions (detected on the basis of the temperature values measured during the experiment). Numerical analyses have been also performed by means of FEM code Ansys©. The numerical results were in quite good agreement with the experimental one, confirming also the reliability of code in reproducing heat transfer phenomena.

  15. The Researches on Performance and Technology of Strengthened Pure Platinum Wire

    Institute of Scientific and Technical Information of China (English)

    ZHAI Buying; WU Baoan; PAN Xiong; YANG Hao; WANG Yunchun; CHEN Xiaojun; WANG Jianshen; LI Guogang; XUE Liqian

    2012-01-01

    This paper discusses about the purity of strengthened pure platinum wire and the development method of platinum micro wire,in order to solve the difficulties of low tensile strength,easy to break,and low rate of micro wire.And it contrasts some performance of strengthened pure platinum wire and sponge Pt wire.The researches draw a conclusion that the thermoelectric properties of strengthened pure platinum micro wire was in accordance with national standards and satisfied users' requirements.

  16. 半柔同轴电缆专用高速浸锡机研究%High-speed semi-flexible coaxial cable Soldering Machine Research

    Institute of Scientific and Technical Information of China (English)

    简裕利

    2014-01-01

    This paper introduces what is semi flexible coaxial cable,domestic production situation of semi flexible coaxial cable,tin dipping process focus on semi flexible coaxial cable is analyzed,and studied the design method of high speed tin dipping machine.%本文介绍了何为半柔同轴电缆,国内半柔同轴电缆的生产现状,重点对半柔同轴电缆的浸锡工艺进行了分析,并研究了高速浸锡机设计方法。

  17. Microfabricated wire arrays for Z-pinch.

    Energy Technology Data Exchange (ETDEWEB)

    Spahn, Olga Blum; Rowen, Adam M.; Cich, Michael Joseph; Peake, Gregory Merwin; Arrington, Christian L.; Nash, Thomas J.; Klem, John Frederick; Romero, Dustin Heinz

    2008-10-01

    Microfabrication methods have been applied to the fabrication of wire arrays suitable for use in Z. Self-curling GaAs/AlGaAs supports were fabricated as an initial route to make small wire arrays (4mm diameter). A strain relief structure that could be integrated with the wire was designed to allow displacements of the anode/cathode connections in Z. Electroplated gold wire arrays with integrated anode/cathode bus connections were found to be sufficiently robust to allow direct handling. Platinum and copper plating processes were also investigated. A process to fabricate wire arrays on any substrate with wire thickness up to 35 microns was developed. Methods to handle and mount these arrays were developed. Fabrication of wire arrays of 20mm diameter was demonstrated, and the path to 40mm array fabrication is clear. With some final investment to show array mounting into Z hardware, the entire process to produce a microfabricated wire array will have been demonstrated.

  18. Soft magnetic wires

    Science.gov (United States)

    Vázquez, M.

    2001-06-01

    An overview of the present state of the art on the preparation techniques, outstanding magnetic properties and applications of soft magnetic micro and nanowires is presented. Rapid solidification techniques (in-rotating-water quenching and drawing methods) to fabricate amorphous microwires with diameter in the range from 100 down to 1 μm are first described. Electrodeposition is also employed to prepare composite microtubes (magnetic coatings) and to fill porous membranes (diameter of the order of 0.1 μm). Magnetic behaviours of interest are related to the different hysteresis loops of samples: square-shaped loops typical of bistable behaviour, and nearly non-hysteretic loop with well-defined transverse anisotropy field. The role played by magnetic dipolar interactions in the magnetic behaviour of arrays of micro and nanowires is described. A particular analysis is done on the giant magnetoimpedance (GMI) effect in the radio and microwave frequency ranges exhibited by ultrasoft microwires. Finally, a few examples of applications are introduced for magnetostrictive and non-magnetostrictive wires, they are: “magnetoelastic pens”, micromotors; DC current-sensors based on GMI, and sharpened amorphous wire tips in spin polarised scanning tunneling microscopy.

  19. 矩形槽同轴布拉格结构的模式匹配分析方法及实验验证%Mode-matching analytic method of a coaxial Bragg structure corrugated with rectangular ripples and its experimental verification

    Institute of Scientific and Technical Information of China (English)

    赖颖昕; 杨雷; 张世昌

    2013-01-01

    Based on the mode-matching method, an analytical model with full-wave coupling is presented for the coaxial Bragg structures corrugated with rectangular ripples, where the expressions of the reflectivity and transmission rate for each involved mode are derived. The validity of the analytical model is examined in terms of a reported experiment, and good agreement between the theoretical results and the experimental measurements is demonstrated. Comparative study is carried out between the present model and the published theoretical results. It is found that the approximate treatment adopted by the previous model leads to notable deviation of the transmission response curve due to the neglect of the evanescent modes excited by rectangular ripples. The analytical method presented in this paper can be expected to provide a useful approach to the characteristic investigation and engineering practice of the coaxial Bragg structures with rectangular ripples.%基于模式匹配法建立了矩形槽同轴布拉格结构的全波耦合分析模型,推导出了不同模式反射率和传输率的计算式,并采用公开报道的实验数据验证了该理论模型。在此基础上就本文理论与其他相关的理论方法进行了比较,发现以前的理论近似模型由于忽略了矩形槽中的消失模而使传输率的频率响应曲线发生偏差。本文建立的理论方法有望为矩形槽同轴布拉格结构的特性研究和工程实践提供一种理论分析手段。

  20. DC Characterization of the Coaxial Superconducting Cable

    Science.gov (United States)

    Šouc, J.; Gömöry, F.; Vojenčiak, M.; Frolek, L.; Isfort, D.; Ehrenberg, J.; Bock, J.

    2008-01-01

    Coaxial cable model with superconducting core and superconducting shield conductor was constructed and tested in DC regime. While the core was already examined in our previous works, in this contribution the detailed study of the superconducting shield conductor in DC conditions is presented. It consists of 16 ReBCO coated tapes with critical current 35 A each connected in parallel. Using shunts with known values placed in series the currents in individual tapes were possible to measure. Distribution of the total cable current into the individual tapes was monitored and its influence on critical current of the cable is discussed.

  1. A Coaxial Cable Fabry-Perot Interferometer for Sensing Applications

    Directory of Open Access Journals (Sweden)

    Ming Luo

    2013-11-01

    Full Text Available This paper reports a novel coaxial cable Fabry-Perot interferometer for sensing applications. The sensor is fabricated by drilling two holes half-way into a coaxial cable. The device physics was described. The temperature and strain responses of the sensor were tested. The measurement error was calculated and analyzed.

  2. A bearingless coaxial magnetic gearbox

    Directory of Open Access Journals (Sweden)

    A.S. Abdel-Khalik

    2014-09-01

    Full Text Available Recently, magnetic gearboxes (MGBs are serious contenders to their conventional mechanical counterparts in terms of reduced maintenance requirements, improved reliability, tolerance to mechanical inaccuracies, and inherent overload protection. MGBs are preferably employed in high speed applications and compact harsh environments subjected to severe shock and vibration. A high gear ratio MGB is also a suitable candidate for single stage high-speed transmission applications such as helicopter power transmissions. In this paper, the conventional planetary magnetic gearbox is equipped with a three-phase winding to provide additional magnetic levitation capabilities besides torque transmission, thus creating a bearingless MGB configuration. This was achieved by adding a three-phase winding in the space between the ferromagnetic pieces. The current in this additional winding is controlled to provide decoupled axial forces irrespective of the transmitted mechanical power. This feature is important to reduce the mechanical losses especially for high-speed rotors and can be a viable method for vibration suppression.

  3. 30 CFR 77.1802 - Insulation of trolley wires, trolley feeder wires and bare signal wires; guarding of trolley...

    Science.gov (United States)

    2010-07-01

    ... wires and bare signal wires; guarding of trolley wires and trolley feeder wires. 77.1802 Section 77.1802... Wires and Trolley Feeder Wires § 77.1802 Insulation of trolley wires, trolley feeder wires and bare..., and bare signal wires shall be adequately guarded: (a) At all points where men are required to work or...

  4. Installation and Adjustment Methods and Operating Characteristics of Coaxial Double-synchronous Generator%采用BOT模式建设垃圾焚烧发电项目风险研究

    Institute of Scientific and Technical Information of China (English)

    唐顺华

    2014-01-01

    Taking Luodong hydropower station as an example, the paper makes a brief description of the structure, installation and adjustment critical points and the operating characteristics of coaxial double-synchronous generator as well as the solutions against the existing problems.%∶垃圾焚烧发电厂作为城市改善环境卫生状况的基础设施,目前大多采用BOT模式建设,目的是为更好推进基础建设市场化的进程及控制垃圾发电项目各项风险,通过列举风险清单来研究垃圾焚烧发电厂采用BOT模式的风险,得出采用BOT模式对垃圾发电项目控制风险的利弊,并结合某城市案例分析研究,得出今后城市垃圾焚烧发电厂等基础设施建设采用BOT模式应当做好风险管理,使政府和投资者做到项目的风险可以控制,带来更好的社会和经济效益。

  5. Topology Optimisation of Wideband Coaxial-to-Waveguide Transitions

    Science.gov (United States)

    Hassan, Emadeldeen; Noreland, Daniel; Wadbro, Eddie; Berggren, Martin

    2017-03-01

    To maximize the matching between a coaxial cable and rectangular waveguides, we present a computational topology optimisation approach that decides for each point in a given domain whether to hold a good conductor or a good dielectric. The conductivity is determined by a gradient-based optimisation method that relies on finite-difference time-domain solutions to the 3D Maxwell’s equations. Unlike previously reported results in the literature for this kind of problems, our design algorithm can efficiently handle tens of thousands of design variables that can allow novel conceptual waveguide designs. We demonstrate the effectiveness of the approach by presenting optimised transitions with reflection coefficients lower than -15 dB over more than a 60% bandwidth, both for right-angle and end-launcher configurations. The performance of the proposed transitions is cross-verified with a commercial software, and one design case is validated experimentally.

  6. Development of a Distributed Crack Sensor Using Coaxial Cable.

    Science.gov (United States)

    Zhou, Zhi; Jiao, Tong; Zhao, Peng; Liu, Jia; Xiao, Hai

    2016-07-29

    Cracks, the important factor of structure failure, reflect structural damage directly. Thus, it is significant to realize distributed, real-time crack monitoring. To overcome the shortages of traditional crack detectors, such as the inconvenience of installation, vulnerability, and low measurement range, etc., an improved topology-based cable sensor with a shallow helical groove on the outside surface of a coaxial cable is proposed in this paper. The sensing mechanism, fabrication method, and performances are investigated both numerically and experimentally. Crack monitoring experiments of the reinforced beams are also presented in this paper, illustrating the utility of this sensor in practical applications. These studies show that the sensor can identify a minimum crack width of 0.02 mm and can measure multiple cracks with a spatial resolution of 3 mm. In addition, it is also proved that the sensor performs well to detect the initiation and development of cracks until structure failure.

  7. Resonant UPS topologies for the emerging hybrid fiber coaxial networks

    Energy Technology Data Exchange (ETDEWEB)

    Pinheiro, H.

    1999-07-01

    Uninterruptible power systems (UPS)are essential to the operation of critical equipment such as life-support systems, computers and telecommunications systems. Ideally, UPS topologies, especially for the emerging hybrid fiber-coaxial networks, must be characterized by relatively small size, high input power factor and trapezoidal waveforms. None of the existing topologies meet all these requirements. Consequently, the objective of this study is to design and analyse UPS topologies that meet these requirements. To meet this objective novel UPS topologies and control techniques are proposed to allow operation of high switching frequencies without penalizing converter efficiency. A self-sustained oscillation control method is proposed to ensure soft switching under all operating conditions.

  8. A new calibration method of constant temperature hot wire anemometer%恒温热线风速仪的一种新型校准方法

    Institute of Scientific and Technical Information of China (English)

    姚惠元; 刘国政; 孙楠; 董军

    2013-01-01

    恒温热线风速仪作为一种风洞流场测量元件,在湍流脉动测速任务中发挥了重要作用。对热线风速仪的校准工作进行了研究,将B样条与递推最小二乘相结合,提出了一种新型校准方法。该方法选取具有低阶光滑特性的B样条函数进行逆向建模,并采用递推最小二乘的方法估计控制参数,有效地提高了校准精度和实时性。通过对实际风洞实验的数据分析,验证了提出的该校正方法的有效性,并表明其具有样本点少、校正精度高、简单实用等显著优点。%As a flow field measuring elements for wind tunnel,the constant temperature hot wire anemometer plays an im-portant role in the measurement of turbulent fluctuation task. The calibration of the hot wire anemometer is studied. Using the B-spline and recursive least squares as a combination,a new calibration method is proposed,which chooses B-spline function with low order smooth characteristics for reverse modeling,and estimates the control parameters using the method of recursive least squares. The method effectively improved the calibration accuracy and real-time. Through the analysis of wind tunnel experimen-tal data,the effectiveness of the correction method is validated. The experiment shows that it has the advantages of fewer sample points,higher correction accuracy,simple and useful.

  9. Double Coaxial Microcatheter Technique for Glue Embolization of Renal Arteriovenous Malformations

    Energy Technology Data Exchange (ETDEWEB)

    Uchikawa, Yoko, E-mail: jauchikawa@gmail.com [University of Tsukuba Hospital, Department of Radiology (Japan); Mori, Kensaku, E-mail: moriken@md.tsukuba.ac.jp [University of Tsukuba, Department of Radiology, Faculty of Medicine (Japan); Shiigai, Masanari, E-mail: m-41gai@yahoo.co.jp [Tsukuba Medical Center Hospital, Department of Radiology (Japan); Konishi, Takahiro, E-mail: soratobukangaruu@gmail.com [University of Tsukuba Hospital, Department of Radiology (Japan); Hoshiai, Sodai, E-mail: hoshiai@sb4.so-net.ne.jp [Ibaraki Prefectural Central Hospital, Department of Radiology (Japan); Ishigro, Toshitaka, E-mail: suzutokei@gmail.com; Hiyama, Takashi, E-mail: med-tak@hotmail.com [University of Tsukuba Hospital, Department of Radiology (Japan); Nakai, Yasunobu, E-mail: nakaiya@tmch.or.jp [Tsukuba Medical Center Hospital, Department of Neurosurgery (Japan); Minami, Manabu, E-mail: mminami@md.tsukuba.ac.jp [University of Tsukuba, Department of Radiology, Faculty of Medicine (Japan)

    2015-10-15

    PurposeTo demonstrate the technical benefit of the double coaxial microcatheter technique for embolization of renal arteriovenous malformations (AVMs) with n-butyl cyanoacrylate and iodized oil (glue).Materials and MethodsSix consecutive patients (1 man and 5 women; mean age 61 years; range 44–77 years) with renal AVMs were included. Five patients had hematuria, and one had a risk of heart failure due to a large intrarenal arteriovenous shunt. All patients underwent transarterial embolization using glue and the double coaxial microcatheter technique with outer 2.6F and inner 1.9F microcatheters. After glue injection, the inner microcatheter was retracted, while the outer microcatheter was retained. We assessed the complications and clinical outcomes of this technique.ResultsTechnical success was achieved in all patients. In 9 sessions, 34 feeding arteries were embolized with glue using the double coaxial microcatheter technique, 1 was embolized with glue using a single microcatheter, and 2 were embolized with coils. The double coaxial microcatheter technique was useful for selecting small tortuous feeding arteries, preventing glue reflux to the proximal arteries, and approaching multiple feeding arteries without complete retraction of the microcatheters. As a minor complication, glue migrated into the venous system in four patients without any sequelae. In all patients, favorable clinical outcomes, including hematuria cessation in five patients and improvement of the large intrarenal arteriovenous shunt in one patient, were obtained without deterioration of renal function.ConclusionGlue embolization with the double coaxial microcatheter technique was useful for treating renal AVMs with multiple tortuous feeding arteries.

  10. Material Properties of Wire for the Fabrication of Knotted Fences

    Directory of Open Access Journals (Sweden)

    Dirk J. Pons

    2014-01-01

    Full Text Available This paper describes the materials properties of galvanised fencing wire, as used in the fabrication of knotted wire fences. A range of physical properties are investigated: tensile strength, ductility in tension, Young’s modulus, three-point bending, and bending span. A range of commercially available wire products were tested. The results show that most, but not all, high tensile wire samples met the minimum tensile and ductility requirements. Young’s modulus results failed to provide any meaningful insights into wire quality. Flexural modulus results also failed to provide any insight into wire quality issues, with no statistically significant differences existing between acceptable and problematic wire batches. The implications are that premature fence failures are unlikely to be caused solely by reduced tensile properties. Existing test methods, including tensile strength and ductility, are somewhat incomplete, perhaps even unreliable, as measures of wire quality.

  11. Spectroscopic properties of colloidal indium phosphide quantum wires

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Lin-Wang; Wang, Fudong; Yu, Heng; Li, Jingbo; Hang, Qingling; Zemlyanov, Dmitry; Gibbons, Patrick C.; Wang, Lin-Wang; Janes, David B.; Buhro, William E.

    2008-07-11

    Colloidal InP quantum wires are grown by the solution-liquid-solid (SLS) method, and passivated with the traditional quantum dots surfactants 1-hexadecylamine and tri-n-octylphosphine oxide. The size dependence of the band gaps in the wires are determined from the absorption spectra, and compared to other experimental results for InP quantum dots and wires, and to the predictions of theory. The photoluminescence behavior of the wires is also investigated. Efforts to enhance photoluminescence efficiencies through photochemical etching in the presence of HF result only in photochemical thinning or photo-oxidation, without a significant influence on quantum-wire photoluminescence. However, photo-oxidation produces residual dot and rod domains within the wires, which are luminescent. The results establish that the quantum-wire band gaps are weakly influenced by the nature of the surface passivation, and that colloidal quantum wires have intrinsically low photoluminescence efficiencies.

  12. Spectroscopic properties of colloidal indium phosphide quantum wires.

    Science.gov (United States)

    Wang, Fudong; Yu, Heng; Li, Jingbo; Hang, Qingling; Zemlyanov, Dmitry; Gibbons, Patrick C; Wang, Lin-Wang; Janes, David B; Buhro, William E

    2007-11-21

    Colloidal InP quantum wires are grown by the solution-liquid-solid (SLS) method, and passivated with the traditional quantum dots surfactants 1-hexadecylamine and tri-n-octylphosphine oxide. The size dependence of the band gaps in the wires are determined from the absorption spectra, and compared to other experimental results for InP quantum dots and wires, and to the predictions of theory. The photoluminescence behavior of the wires is also investigated. Efforts to enhance photoluminescence efficiencies through photochemical etching in the presence of HF result only in photochemical thinning or photooxidation, without a significant influence on quantum-wire photoluminescence. However, photooxidation produces residual dot and rod domains within the wires, which are luminescent. The results establish that the quantum-wire band gaps are weakly influenced by the nature of the surface passivation and that colloidal quantum wires have intrinsically low photoluminescence efficiencies.

  13. Development of Stretched wire measurement bench at IDDL, DAVV Indore

    Science.gov (United States)

    Gehlot, Mona; Mishra, G.

    2016-10-01

    A stretched wire magnetic measurement bench is under development at IDDL, DAVV, Indore. In this method a multistrend wire consisting of N turns is stretched inside the undulator to measure the field integrals of the undulators. The wire moved with constant velocity of translation measures the first integral of the undulator field. The cross motion of the wire at the undulator ends measures the second field integral. The measurement accuracy depends on the wire conditions and material properties. In this paper we follow an analytical approach to find the voltage fluctuations due to wire vibrations during the field measurement. It is shown that the voltage fluctuations depend on undulator gap, magnitude of the impulse on the wire. The mass density and the length of the wire also cause sizeable voltage fluctuations. The analytical derived expression is analysed to optimize system parameters for minimum errors during the measurement.

  14. Kirschner Wire Breakage during Removal Requiring Retrieval

    Directory of Open Access Journals (Sweden)

    Kai Yuen Wong

    2016-01-01

    Full Text Available Kirschner wires (K-wires are widely used for fixation of fractures and dislocations in the hand as they are readily available, reliable, and cost-effective. Complication rates of up to 18% have been reported. However, K-wire breakage during removal is rare. We present one such case illustrating a simple technique for retrieval. A 35-year-old male presented with a distal phalanx fracture of his right middle finger. This open fracture was treated with K-wire fixation. Postoperatively, he developed a pin site infection with associated finger swelling. The K-wire broke during removal with the proximal piece completely retained in his middle phalanx. To minimise risk of osteomyelitis, the K-wire was removed with a novel surgical technique. He had full return of hand function. Intraoperative K-wire breakage has a reported rate of 0.1%. In our case, there was no obvious cause of breakage and the patient denied postoperative trauma. On the other hand, pin site infections are much more common with reported rates of up to 7% in the hand or wrist. K-wire fixation is a simple method for bony stabilisation but can be a demanding procedure with complications often overlooked. It is important to be aware of the potential sequelae.

  15. Optimal Aerodynamic Design of Conventional and Coaxial Helicopter Rotors in Hover and Forward Flight

    Science.gov (United States)

    Giovanetti, Eli B.

    This dissertation investigates the optimal aerodynamic performance and design of conventional and coaxial helicopters in hover and forward flight using conventional and higher harmonic blade pitch control. First, we describe a method for determining the blade geometry, azimuthal blade pitch inputs, optimal shaft angle (rotor angle of attack), and division of propulsive and lifting forces among the components that minimize the total power for a given forward flight condition. The optimal design problem is cast as a variational statement that is discretized using a vortex lattice wake to model inviscid forces, combined with two-dimensional drag polars to model profile losses. The resulting nonlinear constrained optimization problem is solved via Newton iteration. We investigate the optimal design of a compound vehicle in forward flight comprised of a coaxial rotor system, a propeller, and optionally, a fixed wing. We show that higher harmonic control substantially reduces required power, and that both rotor and propeller efficiencies play an important role in determining the optimal shaft angle, which in turn affects the optimal design of each component. Second, we present a variational approach for determining the optimal (minimum power) torque-balanced coaxial hovering rotor using Blade Element Momentum Theory including swirl. We show that the optimal hovering coaxial rotor generates only a small percentage of its total thrust on the portion of the lower rotor operating in the upper rotor's contracted wake, resulting in an optimal design with very different upper and lower rotor twist and chord distributions. We also show that the swirl component of induced velocity has a relatively small effect on rotor performance at the disk loadings typical of helicopter rotors. Third, we describe a more refined model of the wake of a hovering conventional or coaxial rotor. We approximate the rotor or coaxial rotors as actuator disks (though not necessarily uniformly loaded

  16. Reliability of thermal conductivity measurement of liquids by using transient hot-wire, photon-correlation spectroscopy and the laser flash method

    Science.gov (United States)

    Kwon, Suyong; Lee, Joohyun; Kim, Dae Ho

    2016-05-01

    Measuring the thermal conductivity of liquids is important, but not easy, because of the complexity of and the natural convection in liquids, and reliable thermal conductivity measurements in liquids under various sample conditions is essential for data accuracy. We have introduced and developed a validation chain for measuring the thermal conductivity of liquids by using three different experimental methods: the transient hot-wire (THW), the photon correlation spectroscopy (PCS) and the laser flash (LF) methods in the temperature range from -30 to 90 °C. We checked the performance of the validation chain developed in this study by measuring the thermal conductivity of liquid toluene. We found good agreement between the thermal conductivity data obtained by using the THW, PCS and LF methods. To demonstrate the use of this validation chain for measurements of thermophysical properties in liquids, we also showed its use in measuring the specific heat of a volatile liquid, toluene which can be extracted from thermal conductivity, thermal diffusivity, and density measurements without any effects of volatilization.

  17. Effects of distance between tungsten wire and glass substrate on particle size and photochromic characteristic of tungsten oxide prepared by electric current heating method

    Energy Technology Data Exchange (ETDEWEB)

    Hagizawa, T; Honma, T; Kuroki, Y; Okamoto, T; Takata, M, E-mail: takata@vos.nagaokaut.ac.jp [Department of Electrical Engineering, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka, Niigata 940-2188 (Japan)

    2011-10-29

    Tungsten oxide films consisting of particles were prepared on the substrates placed at various distances from the tungsten wires heated by electric current. The shapes of the particles were sphere in an area on the substrate just above the wire while octahedral shape was found in other area. For the spherical particles, with increasing the distance, the mean particle diameter increased, reached its maximum value and gradually decreased. The particles in each area showed the photochromism especially in near-infrared region. The spherical particles with the smallest size exhibited a significant photochromic effect which could be controlled by changing the distance between the wire and the substrate.

  18. Charpak hemispherical wire chamber

    CERN Multimedia

    1970-01-01

    pieces. Mesures are of the largest one. Multi-wire detectors contain layers of positively and negatively charged wires enclosed in a chamber full of gas. A charged particle passing through the chamber knocks negatively charged electrons out of atoms in the gas, leaving behind positive ions. The electrons are pulled towards the positively charged wires. They collide with other atoms on the way, producing an avalanche of electrons and ions. The movement of these electrons and ions induces an electric pulse in the wires which is collected by fast electronics. The size of the pulse is proportional to the energy loss of the original particle.

  19. Photovoltaic Wire Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This Small Business Innovation Research Phase I project will investigate a new architecture for photovoltaic devices based on nanotechnology: photovoltaic wire. The...

  20. On-Wire Lithography

    National Research Council Canada - National Science Library

    Lidong Qin; Sungho Park; Ling Huang; Chad A. Mirkin

    2005-01-01

    .... This procedure, termed on-wire lithography, combines advances in template-directed synthesis of nanowires with electrochemical deposition and wet-chemical etching and allows routine fabrication...

  1. A new method for designing floor slabs on grade due to the difficulty of applying simplified design methods, amongst them being the Portland Cement Association (PCA and Wire Reinforcement Institute (WRI methods

    Directory of Open Access Journals (Sweden)

    Hugo Ernesto Camero Sanabrial

    2010-04-01

    Full Text Available This article presents a methodology for designing slabs on grade for industrial floors where there is an eccentricity between the slab centroid and the gravity centre loads of the loaded axle of forklift trucks travelling over the floor. An example was used for analysing how Portland Cement Association (PCA and the Wire Reinforcement Institute (WRI methods are inadequate for designing floors sublected to this condition. The new proposal for designing slabs on grade for industrial floors has been called the Camero method. An example of an industrial floor designed to be capable of sustaining an infinite number of load applications (or 50-year life was compared to the results of the Camero method and PCA and WRI’s simplified methods. Industrial floors should be capable of sustaining an infinite number of load applications (50-year life if designed with the Camero method; on the other hand, if designed using PCA and WRI methods they will only last one year (in this example the number of axle load applications in a 1-year period was equal to the number of allowable repetitions because they will not be able to sustain an infinite number of load applications. It was concluded that designing plain concrete slabs (without reinforcement on grade according to PCA and the WRI methods leads to slab fatigue, even though extreme fibre stress should not exceed 50 percent (50% of static modulus of concrete rupture and slabs should sustain an infinite number of load repetitions (infinite amount of forklift truck traffic were considered parameters in their design.

  2. Tunable High-Field Magnetization in Strongly Exchange-Coupled Freestanding Co/CoO Core/Shell Coaxial Nanowires.

    Science.gov (United States)

    Salazar-Alvarez, German; Geshev, Julian; Agramunt-Puig, Sebastià; Navau, Carles; Sanchez, Alvaro; Sort, Jordi; Nogués, Josep

    2016-08-31

    The exchange bias properties of Co/CoO coaxial core/shell nanowires were investigated with cooling and applied fields perpendicular to the wire axis. This configuration leads to unexpected exchange-bias effects. First, the magnetization value at high fields is found to depend on the field-cooling conditions. This effect arises from the competition between the magnetic anisotropy and the Zeeman energies for cooling fields perpendicular to the wire axis. This allows imprinting predefined magnetization states to the antiferromagnetic (AFM) shell, as corroborated by micromagnetic simulations. Second, the system exhibits a high-field magnetic irreversibility, leading to open hysteresis loops attributed to the AFM easy axis reorientation during the reversal (effect similar to athermal training). A distinct way to manipulate the high-field magnetization in exchange-biased systems, beyond the archetypical effects, was thus experimentally and theoretically demonstrated.

  3. 1998 wire development workshop proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-04-01

    This report consists of vugraphs of the presentations at the conference. The conference was divided into the following sessions: (1) First Generation Wire Development: Status and Issues; (2) First Generation Wire in Pre-Commercial Prototypes; (3) Second Generation Wire Development: Private Sector Progress and Issues; (4) Second Generation Wire Development: Federal Laboratories; and (5) Fundamental Research Issues for HTS Wire Development.

  4. Flexible tension sensor based on poly(l-lactic acid) film with coaxial structure

    Science.gov (United States)

    Yoshida, Mitsunobu; Onishi, Katsuki; Tanimoto, Kazuhiro; Nishikawa, Shigeo

    2017-10-01

    We have developed a tension sensor with a coaxial structure using a narrow slit ribbon made of a uniaxially stretched poly(l-lactic acid) (PLLA) film for application to a wearable device. The tension sensor is produced as follows. We used tinsel wire as the center conductor of the sensor. The tinsel wire consists of a yarn of synthetic fibers arranged at the center, with a spirally wound rolled copper foil ribbon on the side surface. Next, slit ribbons obtained from a uniaxially oriented film of PLLA are wound helically on the side surface of the center conductor in the direction of a left-handed screw, at an angle of 45° to the central axis. The rolled copper foil is used as an outer conductor and covers the yarn without a gap. The prototype of the fabricated tension sensor has good flexibility, since the sensor is in the form of a filament and consists of a highly flexible material. For the 1 mm tension sensor, it was found that for a tension of 1 N, a charge of 14 pC was output. It was also found that the sensor maintained its room-temperature sensitivity up to 60 °C. Compared with an existing coaxial line sensor using poly(vinylidene fluoride) (PVDF), the sensor using PLLA does not exhibit pyroelectricity, meaning that no undesirable voltage is generated when in contact with body heat, which is a significant advantage as wearable sensors. The result has demonstrated the potential application of the PLLA film to wearable devices for detecting heartbeat and respiration.

  5. Levitation force of small clearance superconductor-magnet system under non-coaxial condition

    Science.gov (United States)

    Xu, Jimin; Jin, Yingze; Yuan, Xiaoyang; Miao, Xusheng

    2017-03-01

    A novel superconducting tilting-pad bearing was proposed for the advanced research of reusable liquid hydrogen turbopump in liquid rocket. The bearing is a combination of superconducting magnetic bearing and hydrodynamic fluid-film bearing. Since the viscosity of cryogenic fuel to activate superconducting state and form hydrodynamic fluid-film is very low, bearing clearance will be very small. This study focuses on the investigation of superconducting levitation force in this kind of small clearance superconductor-magnet system. Based on Bean critical state model and three-dimensional finite element method, an analysis method is presented to obtain the levitation force under such situation. Since the complicated operational conditions and structural arrangement for application in liquid rocket, center lines of bulk superconductor and magnet rotor will usually be in non-coaxial state. Superconducting levitation forces in axial direction and radial direction under non-coaxial situation are also analyzed by the presented method.

  6. Modular design of multi-wire moderator for slow positron source on hard synchrotron radiation SPring-8

    CERN Document Server

    Nikitin, V P; Doronina, P P

    2001-01-01

    One of the optional versions of multi-wire moderator design using modular approach of construction is discussed. The methods of cleaning of tungsten wire surface are reviewed with the aim of increasing reemitted positron yield from moderator wires.

  7. Thin semi-rigid coaxial cables for cryogenics applications

    Science.gov (United States)

    Kushino, Akihiro; Kasai, Soichi

    2013-03-01

    We have developed cryogenic coaxial cables for low temperature signal readout from sensitive devices, such as transition edge sensors, superconducting tunnel junctions, and kinetic inductance detectors. In order to reduce heat penetration into cryogenic stages, low thermal conductivity metals were chosen for both center and outer electrical conductors. Various types of coaxial cables, employing stainless-steel, cupro-nickel, brass, beryllium-copper, phosphor-bronze, niobium, and niobium-titanium, were manufactured using drawing dies. Thermal and electrical properties were investigated between 1 and 8 K. Coaxial cables made of copper alloys showed thermal conductance roughly consistent with literature, meanwhile Nb coaxial cable must be affected by the drawing process and thermal conductance was lowered. Attenuation of superconducting Nb and NbTi coaxial cables were observed to be adequately small up to above 10 GHz compared to those of normal conducting coaxial cables, which are subject to the Wiedemann-Franz law. We also measured normal conducting coaxial cables with silver-plated center conductors to improve high frequency performance.

  8. Electrochemical synthesis of coaxial TiO2–Ag nanowires and their application in photocatalytic water splitting

    NARCIS (Netherlands)

    Maijenburg, A.W.; Veerbeek, J.; Putter, de R.; Veldhuis, S.A.; Zoontjes, M.G.C.; Mul, G.; Montero-Moreno, J.M.; Nielsch, K.; Schäfer, H.; Steinhart, M.; Elshof, ten J.E.

    2014-01-01

    A new method for the formation of coaxial TiO2–Ag nanowires is presented, in which TiO2 nanotubes were formed by the templated electrochemically induced sol–gel method, followed by thermal annealing. The as-formed TiO2 nanotubes have been successfully filled with a Ag core using a subsequent electro

  9. Facile fabrication of high-quality Ag/PS coaxial nanocables based on the mixed mode of soft/hard templates.

    Science.gov (United States)

    Wan, Mimi; Zhao, Wenbo; Peng, Fang; Wang, Qi; Xu, Ping; Mao, Chun; Shen, Jian

    2016-08-01

    A new kind of high-quality Ag/PS coaxial nanocables can be facilely synthesized by using soft/hard templates method. In order to effectively introduce Ag sources into porous polystyrene (PS) nanotubes which were trapped in porous anodic aluminum oxide (AAO) hard template, Pluronic F127 (F127) was used as guiding agent, soft template and reductant. Meanwhile, ethylene glycol solution was also used as solvent and co-reducing agent to assist in the formation of silver nanowires. The influences of concentration of F127 and reducing reaction time on the formation of Ag/PS coaxial nanocables were discussed. Results indicated that the high-quality Ag/PS coaxial nanocables can be obtained by the mixed mode of soft/hard templates under optimized conditions. This strategy is expected to be extended to design more metal/polymer coaxial nanocables for the benefit of creation of complex and functional nanoarchitectures and components.

  10. A compact, coaxial shunt current diagnostic for X pinches.

    Science.gov (United States)

    Wang, Liangping; Zhang, Jinhai; Li, Mo; Zhang, Xinjun; Zhao, Chen; Zhang, Shaoguo

    2015-08-01

    A compact coaxial shunt was applied in X-pinches experiments on Qiangguang pulsed power generator. The coaxial shunt was designed to have a compact construction for smaller inductance and more, for conveniently assembling upon the X pinch load structure. The coaxial shunt is also a cheap current probe and was easily built by research groups. The shunt can monitor a 100 kA high current with a 100 ns rise time. The calibration results showed that the probe used in the experiments has a resistance of 3.2 mΩ with an uncertainty of 3%, and its response time to the step signal is less than 7 ns.

  11. Multipactor Mitigation in Coaxial Lines by Means of Permanent Magnets

    CERN Document Server

    Gonzalez-Iglesias, D; Anza, S; Vague, J; Gimeno, B; Boria, V E; Raboso, D; Vicente, C; Gil, J; Caspers, F; Conde, L

    2014-01-01

    The main aim of this paper is the analysis of the feasibility of employing permanent magnets for the multipactor mitigation in a coaxial waveguide. First, the study of a coaxial line immersed in a uniform axial magnetic field shows that multipactor can be suppressed at any RF frequency if the external magnetic field is strong enough. Both theoretical simulations and experimental tests validate this statement. Next, multipactor breakdown of a coaxial line immersed in a hollow cylindrical permanent magnet is analyzed. Numerical simulations show that multipactor can be suppressed in a certain RF frequency range. The performed experimental test campaign demonstrates the capability of the magnet to avoid the multipactor electron multiplication process.

  12. Circuit Methods for VLF Antenna Couplers. [for use in Loran or Omega receiver systems

    Science.gov (United States)

    Burhans, R. W.

    1977-01-01

    The limitations of different E-field antenna coupler or preamplifier circuits are presented. All circuits were evaluated using actual Loran or Omega signals. Electric field whip or wire antennas are the simplest types which can be used for reception of VLF signals in the 10 to 100 kHz range. JFET or MOSFET transistors provide impedance transformation and some voltage gain in simple circuits where the power for operating the preamplifier uses the same coaxial cable that feeds the signal back to the receiver. The circuit techniques provide useful alternative methods for Loran-Omega receiver system designers.

  13. Assessment of the hardness of different orthodontic wires and brackets produced by metal injection molding and conventional methods

    Directory of Open Access Journals (Sweden)

    Shiva Alavi

    2017-01-01

    Conclusion: MIM orthodontic brackets exhibited hardness values much lower than those of SS orthodontic archwires and were more compatible with NiTi and beta-titanium archwires. A wide range of microhardness values has been reported for conventional orthodontic brackets and it should be considered that the manufacturing method might be only one of the factors affecting the mechanical properties of orthodontic brackets including hardness.

  14. Coaxial direct-detection lidar-system

    DEFF Research Database (Denmark)

    2014-01-01

    The invention relates to a coaxial direct-detection LIDAR system for measuring velocity, temperature and/or particulate density. The system comprises a laser source for emitting a laser light beam having a lasing center frequency along an emission path. The system further comprises an optical...... frequency and/or the center filter frequency may be scanned. The invention further relates to an aircraft airspeed measurement device, and a wind turbine airspeed measurement device comprising the LIDAR system....... delivery system arranged in the emission path of the laser source, the optical delivery system being arranged for delivering the laser light beam in a measuring direction, the optical delivery system further being configured for collecting a return signal backscattered along the measuring direction...

  15. A wave lab inside a coaxial cable

    Science.gov (United States)

    Serra, João M.; Brito, Miguel C.; Alves, J. Maia; Vallera, A. M.

    2004-09-01

    The study of electromagnetic wave propagation in a coaxial cable can be a powerful approach to the study of waves at an undergraduate level. This study can explore different experimental situations, going from those where the finite velocity of propagation must be considered (distributed or transmission line behaviour), to those where this velocity may be considered infinite (lumped behaviour). We believe that the student observation of the existence of these two regimes can be important for the understanding of wave phenomena in general. In this work we show that this can be achieved using low-cost equipment and a set of quite simple experiments, such as the measurement of wave propagation velocity or the study of standing waves and resonance. The results obtained in a coherent set of selected experiments are discussed.

  16. Dissipationless conductance in a topological coaxial cable

    Science.gov (United States)

    Schuster, Thomas; Iadecola, Thomas; Chamon, Claudio; Jackiw, Roman; Pi, So-Young

    2016-09-01

    We present a dynamical mechanism leading to dissipationless conductance, whose quantized value is controllable in a (3+1)-dimensional electronic system. The mechanism is exemplified by a theory of Weyl fermions coupled to a Higgs field, also known as an axion insulator. We show that the insertion of an axial gauge flux can induce vortex lines in the Higgs field, similar to the development of vortices in a superconductor upon the insertion of magnetic flux. We further show that the necessary axial gauge flux can be generated using Rashba spin-orbit coupling or a magnetic field. Vortex lines in the Higgs field are known to bind chiral fermionic modes, each of which serves as a one-way channel for electric charge with conductance e2/h . Combining these elements, we present a physical picture, the "topological coaxial cable," illustrating how the value of the quantized conductance could be controlled in such an axion insulator.

  17. Coaxial Compound Helicopter for Confined Urban Operations

    Science.gov (United States)

    Johnson, Wayne; Elmore, Joshua F.; Keen, Ernest B.; Gallaher, Andrew T.; Nunez, Gerardo F.

    2016-01-01

    A rotorcraft was designed for military operations in a confined urban environment. The specifications included major increases in useful load, range, and speed relative current aircraft capabilities, with a size constraint based on the dimensions of urban streets and intersections. Analysis showed that this combination of requirements is best satisfied by a coaxial main-rotor configuration, with lift compounding to off-load the rotors at high speed, and ducted fans under the rotor disk for propulsion. The baseline design is described, and the aircraft performance is summarized for utility, attack, MEDEVAC, and cargo delivery missions. The impact on size and performance is examined for a number of excursions, including lift-offset main rotors. Technology development required to achieve this advance in capability is recommended.

  18. Dissipationless conductance in a topological coaxial cable

    CERN Document Server

    Schuster, Thomas; Chamon, Claudio; Jackiw, Roman; Pi, So-Young

    2016-01-01

    We present a dynamical mechanism leading to dissipationless conductance, whose quantized value is controllable, in a (3+1)-dimensional electronic system. The mechanism is exemplified by a theory of Weyl fermions coupled to a Higgs field--also known as an axion insulator. We show that the insertion of an axial gauge flux can induce vortex lines in the Higgs field, similarly to the development of vortices in a superconductor upon the insertion of magnetic flux. We further show that the necessary axial gauge flux can be generated using Rashba spin-orbit coupling or a magnetic field. Vortex lines in the Higgs field are known to bind chiral fermionic modes, each of which serves as a one-way channel for electric charge with conductance $e^2/h$. Combining these elements, we present a physical picture, the "topological coaxial cable," illustrating how the value of the quantized conductance could be controlled in such an axion insulator.

  19. INSTABILITY OF GAS/LIQUID COAXIAL JET

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In this article the emphasis was given to the discussion of the effects of diameter ratio and swirling on instability character for the gas/liquid coaxial jet used by Liao, et al.[1]. The results indicate that the finite diameter ratio markedly increases the maximum growth rate, the most unstable wavenumber, as well as the cutoff wavenumber. It implies that the finite diameter ratio will lead to the liquid jet breakup length shorter and the liquid drop size smaller. The effect of the swirling jets is much more complex: for the axisymmetric perturbation mode, the swirling enhances the flow stability, for helical perturbation, the dominant instability mode occurs at n<0. And it is found that in long wave region there exists a new kind of instability modes at n=1 that was not mentioned in Liao et al.'s article. For this new mode, there appears a dominated swirling ratio at which the flow has the maximum growth rate.

  20. Synthesis and characterization of magnetic of Ni/ABS nanocomposites by electrical explosion of wire in liquid and solution blending methods

    Science.gov (United States)

    Thuyet-Nguyen, Minh; Hai-Nguyen, Hong; Kim, Won Joo; Kim, Ho Yoon; Kim, Jin-Chun

    2017-03-01

    Nanomaterials have attracted great attention from chemists, physicists and materials scientists because of their application benefits and special properties. Thermoplastics have been used in many applications such as molding of non-electrical components, conducting, magnetic field and 3D printing. Nanocomposites are known as a material which blends the best properties of components, a high performance material exhibits unusual property combinations and unique design possibilities. In this research, we focused to investigate and report primary results in the synthesis of magnetic nanocomposites based on acrylonitrile butadiene styrene (ABS), which are useful and important thermoplastics. Nickel nanopowder was prepared by electrical explosion of wire in a liquid were used as magnetic component. The composites were prepared by following steps, first the obtained Ni nanopowders were incorporated into the ABS matrix via a solution blending method (drop-casting), and then the solvent was evaporated. The characterizations of obtaining composites were analyzed by field emission scanning electron microscopy, X-Ray Diffraction analysis and vibrating sample magnetometer.

  1. Fast cooldown coaxial pulse tube microcooler

    Science.gov (United States)

    Nast, T.; Olson, J. R.; Champagne, P.; Roth, E.; Kaldas, G.; Saito, E.; Loung, V.; McCay, B. S.; Kenton, A. C.; Dobbins, C. L.

    2016-05-01

    We report the development and initial testing of the Lockheed Martin first-article, single-stage, compact, coaxial, Fast Cooldown Pulse Tube Microcryocooler (FC-PTM). The new cryocooler supports cooling requirements for emerging large, high operating temperature (105-150K) infrared focal plane array sensors with nominal cooling loads of ~300 mW @105K @293K ambient. This is a sequel development that builds on our inline and coaxial pulse tube microcryocoolers reported at CEC 20137, ICC188,9, and CEC201510. The new FC-PTM and the prior units all share our long life space technology attributes, which typically have 10 year life requirements1. The new prototype microcryocooler builds on the previous development by incorporating cold head design improvements in two key areas: 1) reduced cool-down time and 2) novel repackaging that greatly reduces envelope. The new coldhead and Dewar were significantly redesigned from the earlier versions in order to achieve a cooldown time of 2-3 minutes-- a projected requirement for tactical applications. A design approach was devised to reduce the cold head length from 115mm to 55mm, while at the same time reducing cooldown time. We present new FC-PTM performance test measurements with comparisons to our previous pulse-tube microcryocooler measurements and design predictions. The FC-PTM exhibits attractive small size, volume, weight, power and cost (SWaP-C) features with sufficient cooling capacity over required ambient conditions that apply to an increasing variety of space and tactical applications.

  2. 二氧化硅@聚合物同轴纳米纤维%Silica@Polymers Coaxial Nanofibers

    Institute of Scientific and Technical Information of China (English)

    洪友良; 商铁存; 靳玉伟; 杨帆; 王策

    2005-01-01

    The preparation and formation mechamsm ot silica/polyvinylpyrrolidone(PAN) coaxial nanofibers were presented in this paper. The PVP-PAN composite nanofibers were obtained via an electrospinning technique, while SiO2 nanoparticles were prepared according to a Stoeher method. The measurements of water contact angle(WCA), the compared results of silica coating PVPPAN composite nanofibers with PAN nanofibers indicate that much PVP resided on the composite nanofiber surface, which resuks in the occurrence of SiO2@polymer coaxial nanofibers due to the formation of hydrogen bonding between silica and composite nanofibers and subsequent adsorption of silica on the fiber surface.

  3. Accurate core position control in polymer optical waveguides using the Mosquito method for three-dimensional optical wiring

    Science.gov (United States)

    Date, Kumi; Ishigure, Takaaki

    2017-02-01

    Polymer optical waveguides with graded-index (GI) circular cores are fabricated using the Mosquito method, in which the positions of parallel cores are accurately controlled. Such an accurate arrangement is of great importance for a high optical coupling efficiency with other optical components such as fiber ribbons. In the Mosquito method that we developed, a core monomer with a viscous liquid state is dispensed into another liquid state monomer for cladding via a syringe needle. Hence, the core positions are likely to shift during or after the dispensing process due to several factors. We investigate the factors, specifically affecting the core height. When the core and cladding monomers are selected appropriately, the effect of the gravity could be negligible, so the core height is maintained uniform, resulting in accurate core heights. The height variance is controlled in +/-2 micrometers for the 12 cores. Meanwhile, larger shift in the core height is observed when the needle-tip position is apart from the substrate surface. One of the possible reasons of the needle-tip height dependence is the asymmetric volume contraction during the monomer curing. We find a linear relationship between the original needle-tip height and the core-height observed. This relationship is implemented in the needle-scan program to stabilize the core height in different layers. Finally, the core heights are accurately controlled even if the cores are aligned on various heights. These results indicate that the Mosquito method enables to fabricate waveguides in which the cores are 3-dimensionally aligned with a high position accuracy.

  4. Floquet instability of a large density ratio liquid-gas coaxial jet with periodic fluctuation

    Institute of Scientific and Technical Information of China (English)

    LI Zhen; HU Guo-hui; ZHOU Zhe-wei

    2008-01-01

    By numerical simulation of basic flow, this paper extends Floquet stability analysis of interfacial flow with periodic fluctuation into large density ratio range. Sta- bility of a liquid aluminum jet in a coaxial nitrogen stream with velocity fluctuation is investigated by Chebyshev collocation method and the Floquet theory. Parametric reso- nance of the jet and the influences of different physical parameters on the instability are discussed. The results show qualitative agreement with the available experimental data.

  5. Investigation on abnormal group velocities in 1D coaxial photonic crystals

    Institute of Scientific and Technical Information of China (English)

    TONG Yuanwei; ZHANG Yewen; HE Li; LI Hongqiang; CHEN Hong

    2006-01-01

    In this paper, the group velocities of electromagnetic wave for a one-dimensional coaxial photonic crystal in the stop bands with and without defect mode are studied. The results show that the group velocities exceed c (the speed of light in vacuum) in the stop band and it tends to be very slow in the defect mode. The group velocities also are obtained using the method of the transmission line and transmission matrix. The simulating results agree well with the experimental.

  6. MCS-51单片机与二线制串行E2PROM的接口方法%The Method of MCS-51 Series Microcontroller Connect with 2-Wire Serial E2PROM

    Institute of Scientific and Technical Information of China (English)

    臧海河

    2001-01-01

    This article introduce the operation agreement of 2-wire serial E2PROM and the method of MCS-51 serial microcontroller connecte with 2-wire serial E2PROM.It emphatically discuss how to made operation time-series of I2C-bus by software with MCS-51's I/O wire.Sequentially achieve MCS-51 series microcontroller read or write 2-wire serial E2PROM.%本文介绍二线制串行E2PROM的操作协议以及和MCS-51系列单片机的接口方法,着重讨论如何利用MCS-51的两条I/O线通过软件产生I2C总线所要求的操作时序,以实现MCS-51对二线制串行E2PROM的读写操作。

  7. Hydrogenated Silicon Carbide Thin Films Prepared with High Deposition Rate by Hot Wire Chemical Vapor Deposition Method

    Directory of Open Access Journals (Sweden)

    M. M. Kamble

    2014-01-01

    Full Text Available Structural, optical, and electrical properties of hydrogenated silicon carbide (SiC:H films, deposited from silane (SiH4 and methane (CH4 gas mixture by HW-CVD method, were investigated. Film properties are carefully and systematically studied as function of deposition pressure which is varied between 200 mTorr and 500 mTorr. The deposition rate is found to be reasonably high (9.4 nm/s method to prepare stoichiometric SiC:H films.

  8. Minimizing RF heating of conducting wires in MRI.

    Science.gov (United States)

    Yeung, Christopher J; Karmarkar, Parag; McVeigh, Elliot R

    2007-11-01

    Performing interventions using long conducting wires in MRI introduces the risk of focal RF heating at the wire tip. Comprehensive EM simulations are combined with carefully measured experimental data to show that method-of-moments EM field modeling coupled with heat transfer modeling can adequately predict RF heating with wires partially inserted into the patient-mimicking phantom. The effects of total wire length, inserted length, wire position in the phantom, phantom position in the scanner, and phantom size are examined. Increasing phantom size can shift a wire's length of maximum tip heating from about a half wave toward a quarter wave. In any event, with wires parallel to the scanner bore, wire tip heating is minimized by keeping the patient and wires as close as possible to the central axis of the scanner bore. At 1.5T, heating is minimized if bare wires are shorter than 0.6 m or between approximately 2.4 m and approximately 3.0 m. Heating is further minimized if wire insertion into phantoms equivalent to most aqueous soft tissues is less than 13 cm or greater than 40 cm (longer for fatty tissues, bone, and lung). The methods demonstrated can be used to estimate the absolute amount of heating in order to set RF power safety thresholds.

  9. Three-Dimensional Wiring for Extensible Quantum Computing: The Quantum Socket

    Science.gov (United States)

    Béjanin, J. H.; McConkey, T. G.; Rinehart, J. R.; Earnest, C. T.; McRae, C. R. H.; Shiri, D.; Bateman, J. D.; Rohanizadegan, Y.; Penava, B.; Breul, P.; Royak, S.; Zapatka, M.; Fowler, A. G.; Mariantoni, M.

    2016-10-01

    Quantum computing architectures are on the verge of scalability, a key requirement for the implementation of a universal quantum computer. The next stage in this quest is the realization of quantum error-correction codes, which will mitigate the impact of faulty quantum information on a quantum computer. Architectures with ten or more quantum bits (qubits) have been realized using trapped ions and superconducting circuits. While these implementations are potentially scalable, true scalability will require systems engineering to combine quantum and classical hardware. One technology demanding imminent efforts is the realization of a suitable wiring method for the control and the measurement of a large number of qubits. In this work, we introduce an interconnect solution for solid-state qubits: the quantum socket. The quantum socket fully exploits the third dimension to connect classical electronics to qubits with higher density and better performance than two-dimensional methods based on wire bonding. The quantum socket is based on spring-mounted microwires—the three-dimensional wires—that push directly on a microfabricated chip, making electrical contact. A small wire cross section (approximately 1 mm), nearly nonmagnetic components, and functionality at low temperatures make the quantum socket ideal for operating solid-state qubits. The wires have a coaxial geometry and operate over a frequency range from dc to 8 GHz, with a contact resistance of approximately 150 m Ω , an impedance mismatch of approximately 10 Ω , and minimal cross talk. As a proof of principle, we fabricate and use a quantum socket to measure high-quality superconducting resonators at a temperature of approximately 10 mK. Quantum error-correction codes such as the surface code will largely benefit from the quantum socket, which will make it possible to address qubits located on a two-dimensional lattice. The present implementation of the socket could be readily extended to accommodate a

  10. Wire recycling for quantum circuit optimization

    Science.gov (United States)

    Paler, Alexandru; Wille, Robert; Devitt, Simon J.

    2016-10-01

    Quantum information processing is expressed using quantum bits (qubits) and quantum gates which are arranged in terms of quantum circuits. Here, each qubit is associated with a quantum circuit wire which is used to conduct the desired operations. Most of the existing quantum circuits allocate a single quantum circuit wire for each qubit and hence introduce significant overhead. In fact, qubits are usually not needed during the entire computation, only between their initialization and measurement. Before and after that, corresponding wires may be used by other qubits. In this work, we propose a solution which exploits this fact in order to optimize the design of quantum circuits with respect to the required wires. To this end, we introduce a representation of the lifetimes of all qubits which is used to analyze the respective need for wires. Based on this analysis, a method is proposed which "recycles" the available wires and, as a result, reduces the size of the resulting circuit. Numerical tests based on established reversible and fault-tolerant quantum circuits confirm that the proposed solution reduces the number of wires by more than 90% compared to unoptimized quantum circuits.

  11. PMMA/PS coaxial electrospinning: a statistical analysis on processing parameters

    Science.gov (United States)

    Rahmani, Shahrzad; Arefazar, Ahmad; Latifi, Masoud

    2017-08-01

    Coaxial electrospinning, as a versatile method for producing core-shell fibers, is known to be very sensitive to two classes of influential factors including material and processing parameters. Although coaxial electrospinning has been the focus of many studies, the effects of processing parameters on the outcomes of this method have not yet been well investigated. A good knowledge of the impacts of processing parameters and their interactions on coaxial electrospinning can make it possible to better control and optimize this process. Hence, in this study, the statistical technique of response surface method (RSM) using the design of experiments on four processing factors of voltage, distance, core and shell flow rates was applied. Transmission electron microscopy (TEM), scanning electron microscopy (SEM), oil immersion and Fluorescent microscopy were used to characterize fiber morphology. The core and shell diameters of fibers were measured and the effects of all factors and their interactions were discussed. Two polynomial models with acceptable R-squares were proposed to describe the core and shell diameters as functions of the processing parameters. Voltage and distance were recognized as the most significant and influential factors on shell diameter, while core diameter was mainly under the influence of core and shell flow rates besides the voltage.

  12. Control of critical coupling in a coiled coaxial cable resonator.

    Science.gov (United States)

    Huang, Jie; Wei, Tao; Wang, Tao; Fan, Jun; Xiao, Hai

    2014-05-01

    This paper reports a coiled coaxial cable resonator fabricated by cutting a slot in a spring-like coiled coaxial cable to produce a periodic perturbation. Electromagnetic coupling between two neighboring slots was observed. By manipulating the number of slots, critical coupling of the coiled coaxial cable resonator can be well controlled. An ultrahigh signal-to-noise ratio (over 50 dB) at the resonant frequency band was experimentally achieved from a coiled coaxial cable resonator with 38 turns. A theoretic model is developed to understand the device physics. The proposed device can be potentially used as a high quality and flexibly designed band-stop filter or a sensor in structural health monitoring.

  13. Study of the shock structure of supersonic, dual, coaxial, jets

    Energy Technology Data Exchange (ETDEWEB)

    Lee, K. H.; Lee, J. H.; Kim, H. D. [Andong National Univ., Andong (Korea, Republic of)

    2001-07-01

    The shock structure of supersonic, dual, coaxial jet is experimentally investigated. Eight different kinds of coaxial, dual nozzles are employed to observe the major features of the near field shock structure of the supersonic, coaxial, dual jets. Four convergent-divergent supersonic nozzles having the Mach number of 2.0 and 3.0, and are used to compare the coaxial jet flows discharging from two sonic nozzles. The primary pressure ratio is changed in the range between 4.0 and 10.0 and the assistant jet pressure ratio from 1.0 to 4.0. The results obtained show that the impinging angle, nozzle geometry and pressure ratio significantly affect the near field shock structure, Mach disk location and Mach disk diameter. The annular shock system is found depending the assistant and primary jet pressure ratios.

  14. Comparative research on three types of coaxial slow wave structures

    Institute of Scientific and Technical Information of China (English)

    Xiao Ren-Zhen; Liu Guo-Zhi; Chen Chang-Hua

    2008-01-01

    This paper studies three types of coaxial slow wave structures(SWSs):(1)with ripples on both the inner and outer conductors;(2)with ripples on the outer conductor and smooth on the inner one;and(3)with ripples on the inner conductor and smooth on the outer one.The frequencies,coupling impedances,time growth rates and beam-wave interaction efficiencies of the three types of coaxial SWSs are obtained by theoretical analysis.Moreover,the relativistic Cerenkov generators(RCGs)with the three types of coaxial SWSs are simulated with a fully electromagnetic particle-in-cell code,and the results verify the theoretical analysis.It is proved that the RCG with double-rippled coaxial SWS has the highest conversion efficiency and the shortest starting time.

  15. Graphene wire medium: Homogenization and application

    DEFF Research Database (Denmark)

    Andryieuski, Andrei; Chigrin, Dmitry N.; Lavrinenko, Andrei

    2012-01-01

    In this contribution we analyze numerically the optical properties of the graphene wire medium, which unit cell consists of a stripe of graphene embedded into dielectric. We propose a simple method for retrieval of the isofrequency contour and effective permittivity tensor. As an example...... of the graphene wire medium application we demonstrate a reconfigurable hyperlens for the terahertz subwavelength imaging capable of resolving two sources with separation λ0/5 in the far-field....

  16. Measurement of dielectric properties of subcutaneous fat with open-ended coaxial sensors

    Energy Technology Data Exchange (ETDEWEB)

    Alanen, Esko; Nuutinen, Jouni [Department of Oncology, Kuopio University Hospital (Finland); Lahtinen, Tapani [Department of Oncology, Kuopio University Hospital (Finland); Department of Applied Physics, University of Kuopio, FIN-70210, Kuopio (Finland)

    1998-03-01

    A three-layer model of stratum corneum, epidermis/dermis and subcutaneous fat has been developed for the capacitance of an open-ended coaxial line in contact with human skin. Applying the model, the electrical properties of subcutaneous fat can be calculated from skin dielectric measurements with three probes of different sizes. The three-layer model is based on a variational formula for the capacitance of the coaxial probe. An accurate approximation for the dielectric constant of the multilayer cutaneous structure is presented for the inverse problem of solving the dielectric constants of variouslayers. The method was tested at 300 MHz with breast cancer patients who often have radiotherapy-induced late alterations in the structure of subcutaneous fat due to the development of subcutaneous fibrosis. Measurements from 206 sites yielded a good agreement between the dielectric constant of subcutaneous fat and the clinical score for subcutaneous fibrosis. (author)

  17. Investigation on carbon nanomaterials: Coaxial CNT-cylinders and CNT-polymer composite

    Indian Academy of Sciences (India)

    Kalpana Awasthi; T P Yadav; P R Mishra; S Awasthi; O N Srivastava

    2008-06-01

    The macroscopic coaxial carbon cylinders (dia. ∼ 0.5 cm with varying lengths, ∼ 7–10 cm) consisting of aligned carbon nanotube (CNT) stacks have been prepared by controlled spray pyrolysis method. The coaxial carbon cylinders of CNT stacks have been formed directly inside the quartz tube. Another study is done on multi-walled CNTs (MWNTs)–polymer (e.g. polyethylene oxide (PEO), polyacrylamide (PAM)) composite films. We have investigated the structural, electrical and mechanical properties of MWNTs–PEO composites. Composites with different wt% (between 0 and 50 wt% of MWNTs) have been prepared and characterized by the scanning electron microscopic technique. Enhanced electrical conductivity and mechanical strength were observed for the MWNTs–PEO composites. We have also studied the electrical property of MWNTs–PAM composite films.

  18. Separation of Particles in Swirling Flow in Coaxial Channel

    Directory of Open Access Journals (Sweden)

    Vasilevsky Michail

    2016-01-01

    Full Text Available Cyclones are widely used devices to separate a dispersed phase (e.g. particles or droplets from a continuous phase. The separation of particles in coaxial channels with different length is considered in paper. In this study we show that as coaxial channels length grows, the efficiency increases. In addition we demonstrate that as a gap between cylinder components is reduced, the aerosol spray efficiency is reduced also in turbulent flow.

  19. DC Studies of Coaxial Vacuum Gap Breakdown for Pulsed Power Liners

    Science.gov (United States)

    Meisenhelder, C. M.; Bott-Suzuki, S. C.; Haas, D. M.

    2013-10-01

    Previously, pulsed power loads for inertial fusion have been envisioned as cylindrical wire arrays, which could easily be constrained to be in contact with both electrodes for a good electrical connection. Recently, solid liners have become the load of choice for Magnetized Liner Inertial Fusion (MagLIF) experiments which are currently being conducted on the Z-Machine at Sandia National Laboratory. These liners cannot easily be constrained as previous wire loads were, particularly for a repetitive system. The result is a vacuum gap between the driver electrodes and load, which may have unknown effects on the stability and development of the plasma system. DC voltages up to 30 kV will be applied to coaxial electrodes in vacuum to simulate a variety of possible gap parameters for pulsed power liners. This work investigates the breakdown-timing, azimuthal symmetry and coupling of the driver energy to the load as a function of gap parameters to better understand the subsequent behavior of a liner load. Supported by the National Undergraduate Fellowship Program in Plasma Physics and Fusion Energy Sciences and under DE-NA0001836 and GA IR&D funding.

  20. Highly conducting phosphorous doped Nc-Si:H thin films deposited at high deposition rate by hot-wire chemical vapor deposition method.

    Science.gov (United States)

    Waman, V S; Kamble, M M; Ghosh, S S; Mayabadi, Azam; Sathe, V G; Amalnekar, D P; Pathan, H M; Jadkar, S R

    2012-11-01

    In this paper, we report the synthesis of highly conducting phosphorous doped hydrogenated nanocrystalline silicon (nc-Si:H) films at substantially low substrate temperature (200 degrees C) by hot-wire chemical vapor deposition (HW-CVD) method using pure silane (SiH4) and phosphine (PH3) gas mixture without hydrogen dilution. Structural, optical and electrical properties of these films were investigated as a function of PH3 gas-phase ratio. The characterization of these films by low-angle X-ray diffraction, Raman spectroscopy and atomic force microscopy revealed that, the incorporation of phosphorous in nc-Si:H induces an amorphization in the nc-Si:H film structure. Fourier transform infrared spectroscopy analysis indicates that hydrogen predominately incorporated in phosphorous doped n-type nc-Si:H films mainly in di-hydrogen species (Si-H2) and poly-hydrogen (Si-H2)n bonded species signifying that the films become porous, and micro-void rich. We have observed high band gap (1.97-2.37 eV) in the films, though the hydrogen content is low (< 1.4 at.%) over the entire range of PH3 gas-phase ratio studied. Under the optimum deposition conditions, phosphorous doped nc-Si:H films with high dark conductivity (sigma Dark -5.3 S/cm), low charge-carrier activation energy (E(act) - 132 meV) and high band gap (- 2.01 eV), low hydrogen content (- 0.74 at.%) were obtained at high deposition rate (12.9 angstroms/s).

  1. Flow gradient corrections on hot-wire measurements using an X-wire probe

    Science.gov (United States)

    Gooden, J. H. M.; van Lent, M.

    A method has been developed to correct hot-wire measurements by means of a single X-wire probe for the effect of gradients normal to the plane of the wires in the mean flow velocities as well as in the turbulence intensities. Dataprocessing is performed in an iterative way, using the results of measurements with different probe rolling angles, to determine the gradient corrections along the traverse from the previous loop. The method has been applied to measurements in the wake above the trailing edge flap of a wing and it is shown that substantial improvements in the results have been achieved.

  2. Surface Plasmons in Coaxial Metamaterial Cables

    Science.gov (United States)

    Kushwaha, Manvir S.; Djafari-Rouhani, Bahram

    2013-07-01

    Thanks to Victor Veselago for his hypothesis of negative index of refraction, meta-materials — engineered composites — can be designed to have properties difficult or impossible to find in nature: they can have both electrical permittivity (ɛ) and magnetic permeability (μ) simultaneously negative. The metamaterials — henceforth negative-index materials (NIMs) — owe their properties to subwavelength structure rather than to their chemical composition. The tailored electromagnetic response of the NIMs has had a dramatic impact on classical optics: they are becoming known to have changed many basic notions related with electromagnetism. The present article is focused on gathering and reviewing fundamental characteristics of plasmon propagation in coaxial cables fabricated of the right-handed medium (RHM) (with ɛ > 0, μ > 0) and the left-handed medium (LHM) (with ɛ < 0, μ < 0) in alternate shells starting from the innermost cable. Such structures as conceived here may pave the way to some interesting effects in relation to, for example, optical science exploiting the cylindrical symmetry of coaxial waveguides that make it possible to perform all major functions of an optical fiber communication system in which the light is born, manipulated, and transmitted without ever leaving the fiber environment, with precise control over the polarization rotation and pulse broadening. This review also covers briefly the nomenclature, classification, potential applications, and the limitations (related, for example, to the inherent losses) of the NIMs and their impact on classical electrodynamics in general, and in designing the cloaking devices in particular. A recent surge in efforts on invisibility and the cloaking devices seems to have spoiled the researchers worldwide: proposals include not only a way to hide an object without having to wrap the cloak around it, but also to replace a given object with another, thus adding to the deception even further! All this

  3. Using wire shaping techniques and holographic optics to optimize deposition characteristics in wire-based laser cladding

    Science.gov (United States)

    Goffin, N. J.; Higginson, R. L.; Tyrer, J. R.

    2016-12-01

    In laser cladding, the potential benefits of wire feeding are considerable. Typical problems with the use of powder, such as gas entrapment, sub-100% material density and low deposition rate are all avoided with the use of wire. However, the use of a powder-based source material is the industry standard, with wire-based deposition generally regarded as an academic curiosity. This is because, although wire-based methods have been shown to be capable of superior quality results, the wire-based process is more difficult to control. In this work, the potential for wire shaping techniques, combined with existing holographic optical element knowledge, is investigated in order to further improve the processing characteristics. Experiments with pre-placed wire showed the ability of shaped wire to provide uniformity of wire melting compared with standard round wire, giving reduced power density requirements and superior control of clad track dilution. When feeding with flat wire, the resulting clad tracks showed a greater level of quality consistency and became less sensitive to alterations in processing conditions. In addition, a 22% increase in deposition rate was achieved. Stacking of multiple layers demonstrated the ability to create fully dense, three-dimensional structures, with directional metallurgical grain growth and uniform chemical structure.

  4. Cavitation during wire brushing

    Science.gov (United States)

    Li, Bo; Zou, Jun; Ji, Chen

    2016-11-01

    In our daily life, brush is often used to scrub the surface of objects, for example, teeth, pots, shoes, pool, etc. And cleaning rust and stripping paint are accomplished using wire brush. Wire brushes also can be used to clean the teeth for large animals, such as horses, crocodiles. By observing brushing process in water, we capture the cavitation phenomenon on the track of moving brush wire. It shows that the cavitation also can affect the surface. In order to take clear and entire pictures of cavity, a simplified model of one stainless steel wire brushing a boss is adopted in our experiment. A transparent organic tank filled with deionized water is used as a view box. And a high speed video camera is used to record the sequences. In experiment, ambient pressure is atmospheric pressure and deionized water temperature is kept at home temperature. An obvious beautiful flabellate cavity zone appears behind the moving steel wire. The fluctuation of pressure near cavity is recorded by a hydrophone. More movies and pictures are used to show the behaviors of cavitation bubble following a restoring wire. Beautiful tracking cavitation bubble cluster is captured and recorded to show.

  5. Copper wire bonding

    CERN Document Server

    Chauhan, Preeti S; Zhong, ZhaoWei; Pecht, Michael G

    2014-01-01

    This critical volume provides an in-depth presentation of copper wire bonding technologies, processes and equipment, along with the economic benefits and risks.  Due to the increasing cost of materials used to make electronic components, the electronics industry has been rapidly moving from high cost gold to significantly lower cost copper as a wire bonding material.  However, copper wire bonding has several process and reliability concerns due to its material properties.  Copper Wire Bonding book lays out the challenges involved in replacing gold with copper as a wire bond material, and includes the bonding process changes—bond force, electric flame off, current and ultrasonic energy optimization, and bonding tools and equipment changes for first and second bond formation.  In addition, the bond–pad metallurgies and the use of bare and palladium-coated copper wires on aluminum are presented, and gold, nickel and palladium surface finishes are discussed.  The book also discusses best practices and re...

  6. Reduced Burst Release and Enhanced Oral Bioavailability in Shikimic Acid-Loaded Polylactic Acid Submicron Particles by Coaxial Electrospray.

    Science.gov (United States)

    Wang, Miaomiao; Wang, Yuanwen; Omari-Siaw, Emmanuel; Wang, Shengli; Zhu, Yuan; Xu, Ximing

    2016-08-01

    In this study, using the coaxial electrospray method, we prepared submicron particles of the water-soluble drug shikimic acid (SA) with polylactic acid (PLA) as a polymer, to reduce the burst release and enhance the oral bioavailability. In vitro release study performed in HCl solution (pH 1.2) showed that the coaxial electrospray submicron particles could reduce burst release effect and presented a sustained release profile, compared with free SA and the particles prepared by electrospray method. The absorption of SA in the intestinal tract, studied using an in situ perfusion method in rats, also revealed jejunum as the main absorptive segment followed by duodenum and ileum. Moreover, the SA-loaded particles greatly enhanced the absorption of SA in the tested intestinal segments. The intestinal absorption rate was not enhanced with increasing drug concentration (5-15 μg/mL) which suggested that active transport or facilitated diffusion could play vital role in SA absorption. In addition, the SA-loaded PLA coaxial electrospray particle exhibited a prolonged plasma circulation with enhanced bioavailability after oral administration. In all, the coaxial electrospray technique could provide notable advantages for the oral delivery of SA, thereby enhancing its clinical application.

  7. Comparison between Free Abrasive Method and Diamond Wire Method for SiC Materials Cutting%游离磨粒切割法和金刚石线切割法切割SiC的对比

    Institute of Scientific and Technical Information of China (English)

    王磊; 王添依; 张弛; 张海磊; 冯玢

    2014-01-01

    通过采用镀铜钢线配合游离磨粒切割法和金刚石线与砂浆配合切割法对SiC 晶锭分别进行切割试验,在对比两种方法的切割效果基础上,探讨两种切割方法对SiC 晶片表面质量和弯曲度的作用和效果,并对比两种方法的优点。通过探讨总结出镀铜钢线配合游离磨粒切割法切割出的SiC 晶片表面质量较好,但用时较长,适用于小型实验;金刚石线与砂浆配合切割法切割出的SiC 晶片几何参数更好且稳定,且加工效率较高,适用于大型生产。%C utting experim ents for SiC ingots w ere taken through two methods:copper-coated steel wire com bined with free abrasive, and diam ond wire com bined with mortar, respectively. A fterw ards, effects to surface quality and waferwar pofas-cutted wafers by the two methods were discussed and the advantages w ere com pared.Itis confirm ed thatthe form er m ethod leads to better surface quality as wellasmoretimecost,which issuitableforsmall-scaleexperiments;whilethelatermethod leadsto better shape param eter as wellas more process efficiency,which is suitable for large-scale producing.

  8. Synthesis and structural characterization of coaxial nano tubes intercalated of molybdenum disulfide with carbon; Sintesis y caracterizacion estructural de nanotubos coaxiales intercalados de disulfuro de molibdeno con carbono

    Energy Technology Data Exchange (ETDEWEB)

    Reza San German, C.M

    2005-07-01

    In this work the study of some fundamental aspects in the growth of unidimensional systems of coaxial nano tubes from the mold method is approached. This method is an inclusion technique of a precursor reagent into oxide nano porous alumina film (mold), and later applying some processes of synthesis it is gotten to obtain the wished material. The synthesized structures are identified later because they take place by means of the initial formation of nano tubes of MoS{sub 2}, enclosing to carbon nano tubes by the same method, with propylene flow which generates a graphitization process that 'copy' the mold through as it flows. Binary phase MoS{sub 2} + C nano tubes were synthesized by propylene pyrolysis inside MoS{sub 2} nano tubes prepared by template assisted technique. The large coaxial nano tubes constituted of graphite sheets inserted between the MoS{sub 2} layers forming the outer part, and coaxial multi wall carbon nano tubes (MWCNT) intercalated with MoS{sub 2} inside. High resolution electron microscopy (HRTEM), electron energy loss spectroscopy (EELS), high angle annular dark field (HAADF), gatan image filter (GIF), nano beam electron diffraction patterns (NBEDP), along with molecular dynamics simulation and quantum mechanical calculations were used to characterize the samples. The one-dimensional structures exhibit diverse morphologies such as long straight and twisted nano tubes with several structural irregularities. The inter-planar spacing between MoS{sub 2} layers was found to increase from 6.3 to 7.4 A due to intercalation with carbon. Simulated HREM images revealed the presence of these twisted nano structures, with mechanical stretch into intercalate carbon between MoS{sub 2} layers. Our results open up the possibility of using MoS{sub 2} nano tubes as templates for the synthesis of new one- dimensional binary phase systems. (Author)

  9. Micromechanical Modeling for the Deformation of Sand with Non-coaxiality Between Stress and Material Axes

    Science.gov (United States)

    Bennett, K. C.; Chang, C. S.; Borja, R. I.

    2011-12-01

    This research project has taken the micromechanics approach to model the strength and deformation behavior of inherently anisotropic sand subjected to stresses non-coaxial with the material axes. Asymmetric sand grains, such as elongated sand grains, are likely to develop a preferred orientation when deposited during the process of alluvial sedimentation, creating an inherently anisotropic material fabric with horizontally oriented bedding planes. Sand thus exhibits different strength and stress-strain behavior dependent on the direction of loading with respect to the axes of the soil. Accounting for non-coaxiality between the stress and material axes is paramount for the accurate prediction of soil's response to applied loads; however, despite the numerous advancements in constitutive models and numerical methods for geotechnical analysis, the problem of accounting for the effect of non-coaxiality between stress and material axes on soil behavior has not been satisfactorily addressed. Drained hollow cylinder torsional shear (HCTS) compression tests on Toyoura sand were simulated, where the direction of the major principal stresses were applied at various angles to the material axes ranging from 0° to 90° from vertical (i.e., ranging from normal to parallel with the bedding plane). Anisotropic behavior has been attributed to interlocking of the sand particles, where the interlocking is least and sliding occurs most easily on the bedding plane. The degree of interlocking was taken as a material property which varies in three dimensions with respect to the material axes, and has been shown to account for observed anisotropy of material strength. Anisotropy of elastic and plastic strain was accounted for, as was the volumetric strain behavior. The developed micromechanics model has been shown to be capable of predicting anisotropy of strength and stress-strain behavior resulting from non-coaxiality of the stress and material axes.

  10. Wound temperature profiles of coaxial mini-incision versus sleeveless microincision phacoemulsification.

    Science.gov (United States)

    Belkin, Avner; Abulafia, Adi; Michaeli, Adi; Ofir, Shay; Assia, Ehud I

    2017-04-01

    Temperature profiles at the corneal wound of coaxial mini-incision (2.4 mm) cataract surgery and sleeveless microincision (1.1 mm) cataract surgery were compared. Prospective, controlled, paired-eye clinical trial conducted in a tertiary care hospital. Twenty patients with mild-to-moderate bilateral nuclear sclerotic cataract. Twenty patients underwent bilateral cataract surgery within a 1-month period. One eye was operated on by conventional coaxial mini-incision (2.4 mm) phacoemulsification. The second eye underwent microincision surgery by using a naked phacoemulsification tip and a specialized 19-gauge anterior chamber maintainer as the sole fluid source (three-port microincision cataract surgery technique). Patients had moderate bilateral cataracts with no other anterior segment pathology. Temperature at the corneal wound was constantly recorded by using infrared thermal imaging. Temperatures at the corneal wound. Mean temperatures at the corneal surgical wound were not significantly different between the coaxial and sleeveless groups (31.1 °C ± 2.3 vs. 31.0 °C ± 2. 0; P = 0.89). There was also no difference in maximum temperatures reached during phaco-emulsification. Temperatures did not rise above 40 °C during any surgery, and there were no corneal burns. Final visual acuity and intraoperative and postoperative complication rates were similar between the two groups. The temperature profile at the surgical wound using a microincisional sleeveless phacoemulsification technique is comparable with that of the conventional coaxial mini-incision method. © 2016 Royal Australian and New Zealand College of Ophthalmologists.

  11. Research regarding stiffness optimization of wires used for joints actuation from an elephant's trunk robotic arm

    Science.gov (United States)

    Ciofu, C.; Stan, G.

    2016-11-01

    Elephant's trunk robotic arms driven by wires and pulley mechanisms have issues with wires stiffness because of the entailed elastic deformations that is causing errors of positioning. Static and dynamic loads from each joint of the robotic arm affect the stiffness of driving wires and precision positioning. The influence of wires elastic deformation on precision positioning decreases with the increasing of wires stiffness by using different pre-tensioning devices. In this paper, we analyze the variation of driving wires stiffness particularly to each wire driven joint. We obtain optimum wires stiffness variation by using an analytical method that highlights the efficiency of pre-tensioning mechanism. The analysis of driving wires stiffness is necessary for taking appropriate optimization measures of robotic arm dynamic behavior and, thus, for decreasing positioning errors of the elephant's trunk robotic arm with inner actuation through wires/cables.

  12. Influence of sheath solvents on the quality of ethyl cellulose nanofibers in a coaxial electrospinning process.

    Science.gov (United States)

    Yu, Deng-Guang; Li, Xiao-Yan; Chian, Wei; Li, Ying; Wang, Xia

    2014-01-01

    The influence of different types of solvents as sheath fluids on the quality of electrospun ethyl cellulose (EC) nanofibers is investigated in this paper by a modified coaxial process. With 24 w/v % EC in ethanol as electrospinning core fluid and pure solvents including methanol, ethanol and N,N-dimethyl formamide (DMF) as sheath fluids, EC nanofibers were generated by the modified processes. Field emission scanning electron microscope observations demonstrate that the modified process is effective in improving the nanofibers' quality in terms of nanofibers' diameters, distributions and structural uniformity. The key of the modified coaxial process is the reasonable selection of the sheath solvents that is suitable for the drawing process of core EC fluid during the electrpospinning. The EC nanofibers' diameters (D, nm) could be manipulated through the reasonable selection of the type of the sheath solvents based on their boiling point (T, °C) D = 841-3.71T (R=0.9753). This paper provides useful methods for the implementation of the modified coaxial process controllably to obtain polymer nanofibers with high quality.

  13. Un coronographe interf\\'erentiel achromatique coaxial

    CERN Document Server

    Gay, Jean; Rivet, Jean-Pierre; Rabbia, Yves; Buisset, Christophe

    2005-01-01

    On-axis achromatic interfero-coronagraph. We present a new type of stellar interfero-coronagraph, the "CIAXE", which is a variant of the "AIC", the Achromatic Interfero-Coronagraph [3,4]. The CIAXE is characterized by a very simple, compact and fully coaxial optical combination. Indeed, contrarily to the classical AIC which has a Michelson interferometer structure, the CIAXE delivers its output beam on the same axis as the input beam. This will ease its insertion in the focal instrumentation of existing telescopes or next generation ones. Such a device could be a step forward in the field of instrumental search for exoplanets. ----- Dans le but deparvenir \\`a l'imagerie \\`a haute dynamique d'objets comme les exoplan\\`etes, nous pr\\'esentons ici un nouveau concept de coronographe stellaire interf\\'erentiel, le "CIAXE". Il est d\\'eriv\\'e du "CIA", le Coronographe Interf\\'erentiel Achromatique. Le CIAXE se distingue de son pr\\'ed\\'ecesseur par une combinaison optique originale, simplifi\\'ee, tr\\`es compacte et t...

  14. Superconducting properties of granular SmFeAsO{sub 1-x}F{sub x} wires with T{sub c} = 52 K prepared by the powder-in-tube method

    Energy Technology Data Exchange (ETDEWEB)

    Gao Zhaoshun; Wang Lei; Qi Yanpeng; Wang Dongliang; Zhang Xianping; Ma Yanwei [Key Laboratory of Applied Superconductivity, Institute of Electrical Engineering, Chinese Academy of Sciences, PO Box 2703, Beijing 100190 (China); Yang Huan; Wen Haihu [Institute of Physics, Chinese Academy of Sciences, Beijing 100190 (China)], E-mail: ywma@mail.iee.ac.cn

    2008-11-01

    We report the fabrication of Ta-sheathed superconducting SmFeAsO{sub 1-x}F{sub x} wires by the powder-in-tube method for the first time. The transition temperature of the SmFeAsO{sub 0.65}F{sub 0.35} wires was confirmed to be as high as 52 K. High critical fields H{sub c2}(0){>=}120 T as well as current density J{sub c} of 3900 A cm{sup -2} at 5 K were also demonstrated. It should be noted that the J{sub c} exhibits a very weak field dependence behavior, indicating a very encouraging prospect for application of the new superconductors. (rapid communication)

  15. Formal Method for Verifying SpaceWire Encoding Circuit by Applying Theorem Proving%运用定理证明的形式化方法验证SpaceWire编码电路

    Institute of Scientific and Technical Information of China (English)

    李黎明; 关永; 吴敏华; 张杰; 施智平

    2012-01-01

    SpaceWire bus is applied in Space Solar Telescope (SST) project. Testing and simulation are the main methods for verification of SpaceWire bus, but these verifications are incomplete. This study focused on verifying whether the DS encoder circuit developed for SST had faithfully implemented the specification in SpaceWire standard. With the aid of HOL4 tool, this equivalence checking was carried out in a formal verification method, theorem proving. It overcame the limitation of testing and simulation.%我国空间太阳望远镜(SST)项目采用了StaceWire作为传输总线,目前针对Spacewire总线的验证主要采用测试和模拟等传统的方法,这类验证方法是不完备的.本文旨在对SST项目中SpaceWire总线的DS编码电路是否如实地实现标准中的规范要求进行验证,运用定理证明的形式化方法,在HOL4工具上对该电路的设计实现与规范要求的一致性进行验证,克服了传统验证方法的局限性.

  16. Infrared diagnosis of contact wire abrasion based on surface temperature method%基于表面温度法的接触线磨耗红外诊断

    Institute of Scientific and Technical Information of China (English)

    阎玲玲; 金立军; 张文豪; 杨政勃

    2011-01-01

    为解决接触网接触线磨耗检测问题,将红外技术应用到接触线磨耗检测中.开展了接触线磨耗缺陷处温升分析,建立了接触线的表面温度与其横截面积之间的关系,提出了利用接触线缺陷处温度计算横截面积的方法,在测量误差上对接触线磨耗的判断方法进行了评价,在实验室模拟了接触线温升的试验.研究结果表明,利用表面温度法对接触线磨耗的测量误差不超过10%,证明了该方法的可用性.%In order to solve the problems of defect of contact wire abrasion,the infrared technique was investigated. After the analysis of the surface temperature of the defect, the relationship of the surface temperature and its cross-sectional area was established. A method was presented to calculate the cross-sectional area of contact wire abrasion with the temperature of the surface. The judgment of contact wire abrasion was evaluated by the index of measurement error,the temperature rises of contact wire were tested in the laboratory. The experimental results show that the maximum measurement error is less than 10%, so the method proposed is practicable.

  17. The current status of high temperature superconducting wires

    Science.gov (United States)

    Mikhailov, B. P.; Burkhanov, G. S.

    1991-12-01

    The principal technological difficulties associated with the manufacture of high temperature superconducting (HTSC) wires based on yttrium and lanthanum ceramics are briefly reviewed. It is noted that the superconducting and mechanical properties of HTSC wires or ribbons are largely determined by their microstructure. Particular attention is given to the currently used method of producing HTSC wires whereby the ceramic powder is encased in a pipe shell and then deformed by different methods, such as rolling, drawing, or pressing. The requirements for the shell material are examined, and current densities are presented for HTSC wires produced in shells of copper, silver, aluminum, nickel, stainless steel, and zirconium.

  18. Research on static measuring method of wire saw deflection angle%绳锯线弓角静态测量方法的研究

    Institute of Scientific and Technical Information of China (English)

    金闪闪; 邹航; 郭桦

    2016-01-01

    When diamond wire saw cuts circular arc ,wire saw deflection angle will be formed due to resistance in the feed direction .If the bending is serious enough ,the center of the circular plate will be cut excessively and leads to material scrap .In order to solve the problem ,wire saw deflection angle is defined .The static measuring methodology of wire saw deflection angle was proposed .This methodology was based on cantilever type axis force sensor .Through the axis force sensor ,voltage values were output and recorded to calculate wire saw deflection angle . Static measuring experiments were carried out in the physical equipment designed and built by au‐thors .In the experiments ,the steel rope was used to simulate diamond wire saw and created wire saw deflection angle .T he static measuring experiments w ere carried out to study the relationship between the force of guide wheel and wire saw deflection angle .It was found that ,the measured angle was close to the theoretical angle with the increase of initial tension within certain range . Therefore ,when the edge of guide wheel whose axis assembles the force sensor is just contacted with steel cable ,the wire saw deflection angle can be measured relative accurately by this meth‐od .%金刚石绳锯在切割圆弧板材时,受到进给方向的阻力,形成“线弓角”,使板材中部产生“过切”,严重时导致材料报废。为解决这一问题,提出了线弓角的概念,从理论上提出了一种基于悬臂式力传感器的绳锯线弓角的静态测量方法,通过轴力传感器输出的电压值计算出线弓角度。试验在自行设计和搭建的绳锯线弓角测量平台上进行,用钢丝绳模拟串珠绳产生线弓角,并进行导轮受力与线弓角关系的静态测量试验分析,以验证该方法测量线弓角的可行性。试验结果表明:在一定范围内,串珠绳初始张紧力越大,线弓角的计算值越接近理论值。因此,

  19. A Review of Temporary Cardiac Pacing Wires

    Directory of Open Access Journals (Sweden)

    2007-01-01

    Full Text Available Aims: This review aims to tabulate data from all available studies of temporary cardiac pacing wires. Particular aims were to determine the best route of venous access and find ways to reduce complications. The review set out to see if specialist doctors are better at inserting wires than non-specialist doctors. In addition, a contemporary study of wire insertion has been performed to compare modern practice in the UK with the previous studies.Methods: A literature search produced 15 studies available for inclusion. Over 3700 patients from 1973 to 2004 were included. The data was tabulated and attention was given to the route of venous access, the complication rates and whether a specialist or non-specialist doctor had inserted the wire. Results: Internal jugular veins are associated with lowest complication rates and ease of access. Antecubital fossa veins have the highest complication rates. Complication rates are high, especially infections and failure to secure access. Specialist doctors have lower rates of complications than non-specialist doctors. Elderly patient suffer the highest complication rate. Our study showed comparable results to the previous studies.Conclusions: Internal jugular veins are the preferred route for access followed by subclavian and femoral veins. The right side should be used when possible. The use of antibiotics and ultrasound probes must be contemplated for all wire insertions. Alternatives to wire insertion (especially in the elderly must be seriously considered. Setting up an on-call rota would provide experienced doctors to reduce complication rates.

  20. Potentiodynamic studies of stainless steel wire for endourology

    OpenAIRE

    J. Przondziono; W. Walke

    2009-01-01

    Purpose: The purpose of the study is to evaluate resistance to electrochemical corrosion of wire made of Cr-Ni stainless steel, designed for use in endourological treatment. The influence of strain formed in the process of drawing and methods of wire surface preparation to corrosive resistance in artificial urine solution were analysed.Design/methodology/approach: Wire corrosion tests were carried out in the solution of artificial urine with the u...

  1. An Electrostatic Model of Split-Gate Quantum Wires

    OpenAIRE

    Sun, Yinlong; Kirczenow, George; Sachrajda, Andrew. S.; Feng, Yan

    1995-01-01

    We present a theoretical model of split-gate quantum wires that are fabricated from GaAs-AlGaAs heterostructures. The model is built on the physical properties of donors and of semiconductor surfaces, and considerations of equilibrium in such systems. Based on the features of this model, we have studied different ionization regimes of quantum wires, provided a method to evaluate the shallow donor density, and calculated the depletion and pinchoff voltages of quantum wires both before and afte...

  2. [Central venous catheterization complication by a guide wire].

    Science.gov (United States)

    Araki, Yoshiyuki; Fukuda, Isao; Hirano, Masato; Matsuoka, Nobuhiro; Kazama, Tomiei

    2009-03-01

    Central venous catheterization using the Seldinger technique is a well known and often used method. On the other hand, there are also well known complications by needle puncture or by indwelling catheter, there are few reports about a guide wire which got hung up around the tricuspid valve. We report a case in which a guide wire got hung up to the chordae tendineae of the tricuspid valve. To insert the AVA 3Xi (Edwards life science Co. Iervine) from the right internal jugular vein, we inserted a guide wire without ease. Resistance appeared when we tried to remove the wire for 20 cm from the inserted state. The X-ray and the transesophageal echocardiography, showed the guide wire in the right ventricle. As actions to be taken, we advanced the central vein catheter of the EXCV catheter kit (Nippon Sherwood Medical Industries Co., Ltd.) to the tip, and a the guide wire was easily removed. There are many reports of the complication by the central venepuncture, but there are few reports about the guide wire which was entrapped in the vicinity of a tricuspid valve. The tip of the guide wire in this case was bent excessively, but the cause of the damage did not become clear by investigation. When a guide wire became hard to withdraw, we should never withdraw a guide wire blindly, but should search a cause and we should use the material which was matched with the cause.

  3. Optimization of the Single Staggered Wire and Tube Heat Exchanger

    Directory of Open Access Journals (Sweden)

    Arsana I Made

    2016-01-01

    Full Text Available Wire and tube heat exchanger consists of a coiled tube, and wire is welded on the two sides of it in normal direction of the tube. Generally,wire and tube heat exchanger uses inline wire arrangement between the two sides, whereas in this study, it used staggered wire arrangement that reduces the restriction of convection heat transfer. This study performed the optimization of single staggered wire and tube heat exchanger to increase the capacity and reduce the mass of the heat exchanger. Optimization was conducted with the Hooke-Jeeves method, which aims to optimize the geometry of the heat exchanger, especially on the diameter (dw and the distance between wires (pw. The model developed to present heat transfer correlations on single staggered wire and tube heat exchanger was valid. The maximum optimization factor obtained when the diameter wire was 0.9 mm and the distance between wires (pw was 11 mm with the fref value = 1.5837. It means that the optimized design only using mass of 59,10 % and could transfer heat about 98,5 % from the basis design.

  4. Coaxial waveguide for travelling wave MRI at ultrahigh fields.

    Science.gov (United States)

    Andreychenko, Anna; Kroeze, Hugo; Klomp, Dennis W J; Lagendijk, Jan J W; Luijten, Peter R; van den Berg, Cornelis A T

    2013-09-01

    At high magnetic fields the performance of a volume-type body coil inside a human sized MR-scanner is influenced by the waveguide action of the scanner's bore. This can result in undesirable strong radio frequency fields B1+) outside the coil's target volume. A radio frequency (RF) transmit system, exploiting this waveguide action of the bore, is proposed in this work. A coaxial waveguide section is introduced between the antenna and the imaging region. It is shown that the coaxial waveguide has several advantages over the initially proposed travelling wave setup based on the cylindrical waveguide. First, a novel radio frequency matching principle (based on the transmission line impedance matching) is feasible with the coaxial waveguide achieving better radio frequency transmission characteristics, such as homogeneity and power efficiency of B1+ field. In case of body torso imaging, the coaxial waveguide prevents unwanted specific absorptive rate (SAR) deposition outside the target region and thus, effectively decreases local peak SAR values by factor of 5. A 3-fold B1+ gain in the prostate can be achieved with the coaxial waveguide in comparison with the initially proposed travelling wave setup.

  5. Characteristics of Coaxial Vircator in Three Specific Configurations

    Institute of Scientific and Technical Information of China (English)

    邵浩; 杨占峰

    2003-01-01

    As a novel vircator device, the coaxial vircator can attain much higher efficiencythan the common virtual cathode oscillator. In this paper, coaxial vircators in three specificconfigurations are studied to describe the efficiency and frequency characteristics and their depen-dence on geometric parameters. The PIC (Particle in Cell) simulation results show that a powerefficiency over 11% can be obtained from the coaxial vircator with a finite inner anode conduc-tor, and a narrow-band output can be achieved. A direct-coupled coaxial vircator has a slightlylower efficiency of about 8%, but in this configuration the efficiency is not strongly dependenton the geometry parameters. The introduction of a reflecting cavity can effectively improve theefficiency under certain parameters. Meanwhile, the research results also indicate that impropercavity parameters will countervail some inherent advantages of the configuration with a finiteinner conductor, leading to lower efficiency than that of the direct-coupled one. Meanwhile, anexperiment was also carried out to testify the simulation results, and a power efficiency over 3%was obtained from the direct-coupled coaxial vircator.

  6. Welding wire velocity modelling and control using an optical sensor

    DEFF Research Database (Denmark)

    Nielsen, Kirsten M.; Pedersen, Tom S.

    2007-01-01

    In this paper a method for controlling the velocity of a welding wire at the tip of the handle is described. The method is an alternative to the traditional welding apparatus control system where the wire velocity is controlled internal in the welding machine implying a poor disturbance reduction...

  7. High-Q 3D coaxial resonators for cavity QED

    Science.gov (United States)

    Yoon, Taekwan; Owens, John C.; Naik, Ravi; Lachapelle, Aman; Ma, Ruichao; Simon, Jonathan; Schuster, David I.

    Three-dimensional microwave resonators provide an alternative approach to transmission-line resonators used in most current circuit QED experiments. Their large mode volume greatly reduces the surface dielectric losses that limits the coherence of superconducting circuits, and the well-isolated and controlled cavity modes further suppress coupling to the environment. In this work, we focus on unibody 3D coaxial cavities which are only evanescently coupled and free from losses due to metal-metal interfaces, allowing us to reach extremely high quality-factors. We achieve quality-factor of up to 170 million using 4N6 Aluminum at superconducting temperatures, corresponding to an energy ringdown time of ~4ms. We extend our methods to other materials including Niobium, NbTi, and copper coated with Tin-Lead solder. These cavities can be further explored to study their properties under magnetic field or upon coupling to superconducting Josephson junction qubits, e.g. 3D transmon qubits. Such 3D cavity QED system can be used for quantum information applications, or quantum simulation in coupled cavity arrays.

  8. Thickness estimation of the subcutaneous fat using coaxial probe.

    Science.gov (United States)

    Ramezani, Mohammad Hossein; Nadimi, Esmaeil S

    2016-03-01

    In this Letter, a non-invasive method for thickness estimation of the subcutaneous fat layer of abdominal wall is presented by using a coaxial probe. Fat layer has the highest impact on the averaged attenuation parameter of the abdominal wall due to its high thickness and low permittivity. The abdominal wall is modelled as a multi-layer medium and an analytical model for the probe is derived by calculation of its aperture admittance facing to this multi-layer medium. The performance of this model is then validated by a numerical simulation using finite-difference-time-domain (FDTD) analysis. Simulation results show the high impact of the probe dimension and fat layer thickness on the sensitivity of the measured permittivity. The authors further investigate this sensitivity by statistical analysis of the permittivity variations. Finally, measuring in different locations relative to the body surface is presented as a solution to estimate the fat layer thickness in the presence of uncertainty of model parameters.

  9. Multiple coaxial foci generation by phase-only pupil filters

    Science.gov (United States)

    Valle, Pedro J.; Oti, José E.; Canales, Vidal F.; Cagigal, Manuel P.

    2007-04-01

    A new procedure for creating simultaneous multiple foci along the same optical axis with phase-only pupil-plane filters is proposed. Pupil-plane filters consist in phase-only masks described by simple circularly symmetric analytical functions. The axial separation between foci and their energy distribution are independently controlled by two different parameters of the filter. The main advantage of this new design is that, unlike other methods that required slow iterative algorithms, the proposed phase masks are straightforwardly calculated from analytical expressions. Moreover, real-time dynamic foci control could be achieved by using a computer addressed spatial light modulator that allowed the generation of variable phase patterns. The phase profiles we propose can be combined with multiple transversal foci phase patterns to actually form axial replicas of the transversal foci. Thus, it should be expected that three-dimensional structures were dynamically driven fast enough to perform real-time interactive multiple foci manipulation. Experimental verification of the multiple coaxial foci creation by static phase filters is shown.

  10. Combustion behaviors of GO2/GH2 swirl-coaxial injector using non-intrusive optical diagnostics

    Science.gov (United States)

    GuoBiao, Cai; Jian, Dai; Yang, Zhang; NanJia, Yu

    2016-06-01

    This research evaluates the combustion behaviors of a single-element, swirl-coaxial injector in an atmospheric combustion chamber with gaseous oxygen and gaseous hydrogen (GO2/GH2) as the propellants. A brief simulated flow field schematic comparison between a shear-coaxial injector and the swirl-coaxial injector reveals the distribution characteristics of the temperature field and streamline patterns. Advanced optical diagnostics, i.e., OH planar laser-induced fluorescence and high-speed imaging, are simultaneously employed to determine the OH radical spatial distribution and flame fluctuations, respectively. The present study focuses on the flame structures under varying O/F mixing ratios and center oxygen swirl intensities. The combined use of several image-processing methods aimed at OH instantaneous images, including time-averaged, root-mean-square, and gradient transformation, provides detailed information regarding the distribution of the flow field. The results indicate that the shear layers anchored on the oxygen injector lip are the main zones of chemical heat release and that the O/F mixing ratio significantly affects the flame shape. Furthermore, with high-speed imaging, an intuitionistic ignition process and several consecutive steady-state images reveal that lean conditions make it easy to drive the combustion instabilities and that the center swirl intensity has a moderate influence on the flame oscillation strength. The results of this study provide a visualized analysis for future optimal swirl-coaxial injector designs.

  11. Technique of Coaxial Frame in Reflection for the Characterization of Single and Multilayer Materials with Correction of Air Gap

    Directory of Open Access Journals (Sweden)

    Zarral Lamia

    2014-01-01

    Full Text Available Techniques based on fixture probes in reflection are used in microwave reflectometry as a novel diagnostic tool for detection of skin cancers, for complex permittivity measurements on liquid samples and oil shale, and for complex dielectric permittivity of animals’ organs and tissues measurements in microwave band for the needs of modern veterinary medicine. In this work, we have developed a technique to characterize multilayer materials in a broadband frequency range. A coaxial probe in reflection has been specially developed for microelectronic substrate. Using SMA connector, loss tangent of 10−4 and relative permittivity have been measured with an error of 0.145%. The extension of the coaxial probe in reflection technique to multilayer substrates such as Delrin and Teflon permitted to measure bilayer material provided the good knowledge of electrical parameters and dimensions of one layer. In the coaxial transmission line method, a factor that greatly influences the accuracy of the results is the air gaps between the material under test and the coaxial test fixture. In this paper, we have discussed the influence of the air gaps (using samples of 0.5 mm air gaps and the measures that can be taken to minimize that influence when material is measured. The intrinsic values thus determined have been experimentally verified. We have described the structure of the test fixture, its calibration issues, and the experimental results. Finally, electromagnetism simulations showed that the best results can be obtained.

  12. An additional S-shaped structure for sensitivity improvement of coaxial probe for permittivity determination of low loss materials

    Science.gov (United States)

    Jiao, Xingmin; Jin, Wei; Yang, Xiaoqing

    2015-05-01

    Permittivity measurement of materials is important in microwave chemistry, microwave material processing and microwave heating. The open-ended coaxial line method is one of the most popular and effective means for permittivity measurement. However, the conventional coaxial probe has difficulty in distinguishing small permittivity variations for low loss media. In this paper an additional S-shaped structure is proposed for sensitivity improvement of a coaxial probe for permittivity determination of low loss materials at 2.45 GHz. The small permittivity variation can be distinguished due to field enhancement generated by the additional S-shaped structure. We studied the variation of reflection coefficient amplitude for three kinds of samples with different moisture content, within the probe at different insertion depths. We find that the conventional coaxial probe cannot distinguish small permittivity variations until the moisture content of materials reaches 3%. Meanwhile, the probe with the S-shaped structure can detect such small permittivity variations when the moisture content of samples changes by only 1%. The experimental results demonstrate that the new probe proposed in this paper is reliable and feasible.

  13. Synthesis and electrochemical performance of multi-walled carbon nanotube/polyaniline/MnO 2 ternary coaxial nanostructures for supercapacitors

    Science.gov (United States)

    Li, Qiang; Liu, Jianhua; Zou, Jianhua; Chunder, Anindarupa; Chen, Yiqing; Zhai, Lei

    Multi-walled carbon nanotube (MWCNT)/polyaniline (PANI)/MnO 2 (MPM) ternary coaxial structures are fabricated as supercapacitor electrodes via a simple wet chemical method. The electrostatic interaction between negative poly(4-styrenesulfonic acid) (PSS) molecules and positive Mn 2+ ions causes the generation of MnO 2 nanostructures on MWCNT surfaces while the introduction of PANI layers with appropriate thickness on MWCNT surfaces facilitates the formation of MWCNT/PANI/MnO 2 ternary coaxial structures. The thickness of PANI coatings is controlled by tuning the aniline/MWCNT ratio. The effect of PANI thickness on the subsequent MnO 2 nanoflakes attachment onto MWCNTs, and the MPM structures is investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and field-emission scanning electron microscopy (FESEM). The results suggest that appropriate thickness of PANI layers is important for building MPM ternary coaxial structures without the agglomeration of MnO 2 nanoflakes. The MPM ternary coaxial structures provide large interaction area between the MnO 2 nanoflakes and electrolyte, and improve the electrochemical utilization of the hydrous MnO 2, and decrease the contact resistance between MnO 2 and PANI layer coated MWCNTs, leading to intriguing electrochemical properties for the applications in supercapacitors such as a specific capacitance of 330 Fg -1 and good cycle stability.

  14. Numerical simulation of heat transfer and fluid flow in coaxial laser cladding process for direct metal deposition

    Science.gov (United States)

    Qi, Huan; Mazumder, Jyotirmoy; Ki, Hyungson

    2006-07-01

    The coaxial laser cladding process is the heart of direct metal deposition (DMD). Rapid materials processing, such as DMD, is steadily becoming a tool for synthesis of materials, as well as rapid manufacturing. Mathematical models to develop the fundamental understanding of the physical phenomena associated with the coaxial laser cladding process are essential to further develop the science base. A three-dimensional transient model was developed for a coaxial powder injection laser cladding process. Physical phenomena including heat transfer, melting and solidification phase changes, mass addition, and fluid flow in the melt pool, were modeled in a self-consistent manner. Interactions between the laser beam and the coaxial powder flow, including the attenuation of beam intensity and temperature rise of powder particles before reaching the melt pool were modeled with a simple heat balance equation. The level-set method was implemented to track the free surface movement of the melt pool, in a continuous laser cladding process. The governing equations were discretized using the finite volume approach. Temperature and fluid velocity were solved for in a coupled manner. Simulation results such as the melt pool width and length, and the height of solidified cladding track were compared with experimental results and found to be reasonably matched.

  15. Distribution of wire deformation within strands of wire ropes

    Institute of Scientific and Technical Information of China (English)

    MA Jun; GE Shi-rong; ZHANG De-kun

    2008-01-01

    Using ANSYS software, we developed a modeling program for several kinds of wire ropes with metal cores and built a geometric model for the 6x19 IWS wire rope. Through proper grid partitioning, a finite element model for calculating the deformation of wire rope was obtained. Completely constraining one end of the wire rope and applying an axial force to the other end, we established the boundary conditions for solving the model. In addition, we numerically simulated the stress and deformation of the wire, obtaining the deformation distribution of each wire within the wire rope under different laying directions.At the end, a tensile test of the 6x19 IWS wire rope was carried out and the results of simulation and experiment compared.

  16. Polyacrylonitrile nanofibers coated with silver nanoparticles using a modified coaxial electrospinning process

    Directory of Open Access Journals (Sweden)

    Yu DG

    2012-11-01

    Full Text Available Deng-Guang Yu,1 Jie Zhou,2 Nicholas P Chatterton,3 Ying Li,1 Jing Huang,2 Xia Wang11School of Materials Science and Engineering, University of Shanghai for Science and Technology, Shanghai, People's Republic of China; 2School of Life Sciences, East China Normal University, Shanghai, People's Republic of China; 3Faculty of Life Sciences, London Metropolitan University, London, United KingdomBackground: The objective of this investigation was to develop a new class of antibacterial material in the form of nanofibers coated with silver nanoparticles (AgNPs using a modified coaxial electrospinning approach. Through manipulation of the distribution on the surface of nanofibers, the antibacterial effect of Ag can be improved substantially.Methods: Using polyacrylonitrile (PAN as the filament-forming polymer matrix, an electrospinnable PAN solution was prepared as the core fluid. A silver nitrate (AgNO3 solution was exploited as sheath fluid to carry out the modified coaxial electrospinning process under varied sheath-to-core flow rate ratios.Results: Scanning electron microscopy and transmission electron microscopy demonstrated that the sheath AgNO3 solution can take a role in reducing the nanofibers' diameters significantly, a sheath-to-core flow rate ratio of 0.1 and 0.2 resulting in PAN nanofibers with diameters of 380 ± 110 nm and 230 ± 70 nm respectively. AgNPs are well distributed on the surface of PAN nanofibers. The antibacterial experiments demonstrated that these nanofibers show strong antimicrobial activities against Bacillus subtilis Wb800, and Escherichia coli dh5α.Conclusion: Coaxial electrospinning with AgNO3 solution as sheath fluid not only facilitates the electrospinning process, providing nanofibers with reduced diameters, but also allows functionalization of the nanofibers through coating with functional ingredients, effectively ensuring that the active antibacterial component is on the surface of the material, which leads to

  17. Wiring and lighting

    CERN Document Server

    Kitcher, Chris

    2013-01-01

    Wiring and Lighting provides a comprehensive guide to DIY wiring around the home. It sets out the regulations and legal requirements surrounding electrical installation work, giving clear guidelines that will enable the reader to understand what electrical work they are able to carry out, and what the testing and certification requirements are once the work is completed. Topics covered include: Different types of circuits; Types of cables and cable installation under floors and through joists; Isolating, earthing and bonding; Accessory boxes and fixings; Voltage bands; Detailed advice on safe

  18. Modern wiring practice

    CERN Document Server

    Steward, W E

    2012-01-01

    Continuously in print since 1952, Modern Wiring Practice has now been fully revised to provide an up-to-date source of reference to building services design and installation in the 21st century. This compact and practical guide addresses wiring systems design and electrical installation together in one volume, creating a comprehensive overview of the whole process for contractors and architects, as well as electricians and other installation engineers. Best practice is incorporated throughout, combining theory and practice with clear and accessible explanation, all

  19. Surface cleaning of metal wire by atmospheric pressure plasma

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, T., E-mail: tsubasa@oshima-k.ac.jp [Electronic-Mechanical Engineering Department, Oshima National College of Maritime Technology, 1091-1 Komatsu, Suo-Oshima, Yamaguchi (Japan); Department of Electrical Engineering, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka (Japan); Buttapeng, C. [School of Electrical and Energy Engineering, University of the Thai Chamber of Commerce, 126/1, Vibhavadee-Rungsit, Dindaeng, Bangkok 10400 (Thailand); Furuya, S. [Faculty of Education, Gunma University, 4-2 Aramaki, Maebashi (Japan); Harada, N. [Department of Electrical Engineering, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka (Japan)

    2009-11-30

    In this study, the possible application of atmospheric pressure dielectric barrier discharge plasma for the annealing of metallic wire is examined and presented. The main purpose of the current study is to examine the surface cleaning effect for a cylindrical object by atmospheric pressure plasma. The experimental setup consists of a gas tank, plasma reactor, and power supply with control panel. The gas assists in the generation of plasma. Copper wire was used as an experimental cylindrical object. This copper wire was irradiated with the plasma, and the cleaning effect was confirmed. The result showed that it is possible to remove the tarnish which exists on the copper wire surface. The experiment reveals that atmospheric pressure plasma is usable for the surface cleaning of metal wire. However, it is necessary to examine the method for preventing oxidization of the copper wire.

  20. COLD ROLLING ORTHODONTIC WIRES OF AUSTENITIC STAINLESS STEEL AISI 304

    Directory of Open Access Journals (Sweden)

    Rodrigo Santos Messner

    2013-03-01

    Full Text Available Austenitic stainless steels wires are widely used in the final stages of orthodontic treatment. The objective of this paper is to study the process of conformation of rectangular wires from round wires commercial austenitic stainless steel AISI 304 by the process of cold rolling. The wire quality is evaluated by means of dimensional analysis, microhardness measurements, tensile strength and fractographic analysis of the wires subjected to tensile tests. Also a study on the application of finite element method to simulate the process, comparing the force and rolling stress obtained in the rolling is done. The simulation results are consistent with those obtained in the actual process and the rolled wires show ductile fracture, tensile strength and dimensional variations appropriate to orthodontic standards. The fracture morphology shows the model cup-cone type besides the high deformation and hardness inherent in the cold rolling process.

  1. Structure of ordered coaxial and scroll nanotubes: general approach.

    Science.gov (United States)

    Khalitov, Zufar; Khadiev, Azat; Valeeva, Diana; Pashin, Dmitry

    2016-01-01

    The explicit formulas for atomic coordinates of multiwalled coaxial and cylindrical scroll nanotubes with ordered structure are developed on the basis of a common oblique lattice. According to this approach, a nanotube is formed by transfer of its bulk analogue structure onto a cylindrical surface (with a circular or spiral cross section) and the chirality indexes of the tube are expressed in the number of unit cells. The monoclinic polytypic modifications of ordered coaxial and scroll nanotubes are also discussed and geometrical conditions of their formation are analysed. It is shown that tube radii of ordered multiwalled coaxial nanotubes are multiples of the layer thickness, and the initial turn radius of the orthogonal scroll nanotube is a multiple of the same parameter or its half.

  2. Swirl Coaxial Injector Testing with LOX/RP-J

    Science.gov (United States)

    Greene, Sandra Elam; Casiano, Matt

    2013-01-01

    Testing was conducted at NASA fs Marshall Space Flight Center (MSFC) in the fall of 2012 to evaluate the operation and performance of liquid oxygen (LOX) and kerosene (RP ]1) in an existing swirl coaxial injector. While selected Russian engines use variations of swirl coaxial injectors, component level performance data has not been readily available, and all previously documented component testing at MSFC with LOX/RP ]1 had been performed using a variety of impinging injector designs. Impinging injectors have been adequate for specific LOX/RP ]1 engine applications, yet swirl coaxial injectors offer easier fabrication efforts, providing cost and schedule savings for hardware development. Swirl coaxial elements also offer more flexibility for design changes. Furthermore, testing with LOX and liquid methane propellants at MSFC showed that a swirl coaxial injector offered improved performance compared to an impinging injector. So, technical interest was generated to see if similar performance gains could be achieved with LOX/RP ]1 using a swirl coaxial injector. Results would allow such injectors to be considered for future engine concepts that require LOX/RP ]1 propellants. Existing injector and chamber hardware was used in the test assemblies. The injector had been tested in previous programs at MSFC using LOX/methane and LOX/hydrogen propellants. Minor modifications were made to the injector to accommodate the required LOX/RP ]1 flows. Mainstage tests were performed over a range of chamber pressures and mixture ratios. Additional testing included detonated gbombs h for stability data. Test results suggested characteristic velocity, C*, efficiencies for the injector were 95 ]97%. The injector also appeared dynamically stable with quick recovery from the pressure perturbations generated in the bomb tests.

  3. 77 FR 8898 - Certain Coaxial Cable Connectors and Components Thereof and Products Containing Same; Notice of...

    Science.gov (United States)

    2012-02-15

    ... COMMISSION Certain Coaxial Cable Connectors and Components Thereof and Products Containing Same; Notice of... the sale within the United States after importation of certain coaxial cable connectors and components... declare that its coaxial cable connectors, utilizing an axial but not radial compression for...

  4. 76 FR 68504 - Advisory Opinion Proceeding; Certain Coaxial Cable Connectors and Components Thereof and Products...

    Science.gov (United States)

    2011-11-04

    ... COMMISSION Advisory Opinion Proceeding; Certain Coaxial Cable Connectors and Components Thereof and Products... importation of certain coaxial cable connectors and components thereof and products containing the same by... under Commission Rule 210.79 (19 CFR 210.79) that would declare that its coaxial cable...

  5. Snaps to Connect Coaxial and Microstrip Lines in Wearable Systems

    Directory of Open Access Journals (Sweden)

    Tiiti Kellomäki

    2012-01-01

    Full Text Available Commercial snaps (clothing fasteners can be used to connect a coaxial cable to a microstrip line. This is useful in the context of wearable antennas, especially in consumer applications and disposable connections. The measured S-parameters of the transition are presented, and an equivalent circuit and approximate equations are derived for system design purposes. The proposed connection is usable up to 1.5 GHz (10 dB return loss condition, and the frequency range can be extended to 2 GHz if a thinner, more flexible coaxial cable is used.

  6. Practical wiring in SI units

    CERN Document Server

    Miller, Henry A

    2013-01-01

    Practical Wiring, Volume 1 is a 13-chapter book that first describes some of the common hand tools used in connection with sheathed wiring. Subsequent chapters discuss the safety in wiring, cables, conductor terminations, insulating sheathed wiring, conductor sizes, and consumer's control equipments. Other chapters center on socket outlets, plugs, lighting subcircuits, lighting accessories, bells, and primary and secondary cells. This book will be very valuable to students involved in this field of interest.

  7. 3D Wire 2015

    DEFF Research Database (Denmark)

    Jordi, Moréton; F, Escribano; J. L., Farias

    This document is a general report on the implementation of gamification in 3D Wire 2015 event. As the second gamification experience in this event, we have delved deeply in the previous objectives (attracting public areas less frequented exhibition in previous years and enhance networking) and ha......, improves socialization and networking, improves media impact, improves fun factor and improves encouragement of the production team....

  8. One-wire thermocouple

    Science.gov (United States)

    Goodrich, W. D.; Staimach, C. J.

    1977-01-01

    Nickel alloy/constantan device accurately measures surface temperature at precise locations. Device is moderate in cost and simplifies fabrication of highly-instrumented seamless-surface heat-transfer models. Device also applies to metal surfaces if constantan wire has insulative coat.

  9. Ultrasonic Welding of Wires and Cables

    Science.gov (United States)

    Heinz, Stefan; Wagner, Guntram; Eifler, Dietmar

    2012-03-01

    In the automobile industry, ultrasonic metal welding is an established method. At the Institute of Materials Science and Engineering (WKK) at the University of Kaiserslautern, Germany, systematic investigations of the weldability of Al-wires and flat flexible copper cables were carried out. In the case of Al-wires, joints with cross-sectional area of up to 80 mm2 and tensile shear load of about 3500 N were finally realized. Furthermore, methods to reduce unintentional adherence between the sonotrode coupling face and the Al-wires were developed. To realize FFC joints, ultrasonic spot welding systems and ultrasonic torsion welding systems were used. A central purpose of these investigations is the development of a system to enable welding through the insulation of the FFC without weakening the base material.

  10. Research on Welding Methods for 65Mn Spring Steel Wire%65Mn弹簧钢丝焊接方法的研究

    Institute of Scientific and Technical Information of China (English)

    郭涛; 范宇洪; 沙琳

    2012-01-01

    The welding test of 65Mn steel wire (φ0.7mm)was carried out by Argo tungsten-arc welding. The optimal welding current and process parameters of heat treatment were obtained, and the requirements of strength, elasticity and anti-fatigue were achieved.%采用钨极氩弧焊方法对φ0.7 mm的65Mn钢丝进行了焊接试验研究,获得了最佳焊接电流及热处理工艺参数,达到了强度、弹性及抗疲劳性能的要求.

  11. Research on quantum efficiency of GaN wire photocathode

    Science.gov (United States)

    Xia, Sihao; Liu, Lei; Diao, Yu; Kong, Yike

    2017-02-01

    On the basis of three-dimensional continuity equation in semiconductors and finite difference method, the carrier concentration and the quantum efficiency of GaN wire photocathode as a function of incident photon energy are achieved. Results show that the quantum efficiency of the wire photocathode is largely enhanced compared with the conventional planar photocathode. The superiority of the wire photocathode is reflected in its structure with surrounding surfaces. The quantum efficiency of the wire photocathode largely depends on the wire width, surface reflectivity, surface escape probability and incident angle of light. The back interface recombination rate, however, has little influences on the quantum efficiency of the wire photocathode. The simulation results suggest that the optimal width for photoemission is 150-200 nm. Besides, the quantum efficiency increases and decreases linearly with increasing surface escape probability and surface reflectivity, respectively. With increasing ratio of wire spacing to wire height, the optimal incident angle of light is reduced. These simulations are expected to guide the preparation of a better performing GaN wire photocathode.

  12. Magnetohydrodynamic Simulation of the Chordal Wire-Array Plasma Flow Switch

    Science.gov (United States)

    Domonkos, Matthew; Amdahl, David

    2015-11-01

    The coaxial plasma flow switch (PFS) using a chordal wire array armature was first studied experimentally and computationally in the 1980's. That work revealed significant current interruption (dI/dt ~ 5 MA/ μs) as well as continuum x-ray emission representative of 30-45 keV bremsstrahlung. The work concluded that the voltage spike associated with the current interruption accelerated highly magnetized ions downstream at high velocity, and that energy exchange between the ions and electrons and their subsequent acceleration at the downstream boundary of the apparatus were responsible for the x-ray production. This work revisits the PFS operation up to and just beyond the point of armature lift-off from the coaxial section, where the magnetohydrodynamic model is valid and relevant. The early-time energy deposition in the wires from the pulse discharge is modeled in high-resolution 1-D and is used to set the initial conditions for the full-scale 3-D calculation. The wire array is assumed to have expanded from the initial r =0.01 cm uniformly and only in the axial direction, while the areal mass density retains its intended variation with radius. 3-D calculations are used to examine the armature, including magnetic field diffusion, as it is propelled along the coaxial geometry. These calculations will be used to set the initial conditions for follow-on particle or particle-fluid hybrid calculations of the propagation of ions and electrons to downstream obstacles and to calculate the x-ray production from the interactions of the flowing plasma with the obstacles.

  13. Integrated Electrical Wire Insulation Repair System

    Science.gov (United States)

    Williams, Martha; Jolley, Scott; Gibson, Tracy; Parks, Steven

    2013-01-01

    An integrated system tool will allow a technician to easily and quickly repair damaged high-performance electrical wire insulation in the field. Low-melt polyimides have been developed that can be processed into thin films that work well in the repair of damaged polyimide or fluoropolymer insulated electrical wiring. Such thin films can be used in wire insulation repairs by affixing a film of this low-melt polyimide to the damaged wire, and heating the film to effect melting, flow, and cure of the film. The resulting repair is robust, lightweight, and small in volume. The heating of this repair film is accomplished with the use of a common electrical soldering tool that has been modified with a special head or tip that can accommodate the size of wire being repaired. This repair method can furthermore be simplified for the repair technician by providing replaceable or disposable soldering tool heads that have repair film already "loaded" and ready for use. The soldering tool heating device can also be equipped with a battery power supply that will allow its use in areas where plug-in current is not available

  14. Flow of a Jeffery-Six Constant Fluid Between Coaxial Cylinders with Heat Transfer Analysis

    Institute of Scientific and Technical Information of China (English)

    Muhammad Yousaf Malik; Azad Hussain; Sohail Nadeem

    2011-01-01

    In the present investigation we have discussed the flow of a Jeffrey-six constant incompressible fluid between two infinite coaxial cylinders in the presence of heat transfer analysis. The governing equations of Jeffrey-six constant fluid along with energy equation have been derived in cylindrical coordinates. The highly nonlinear equations are simplified with the help of non-dimensional parameters and then solved analytically with the help of homotopy analysis method (HAM) for two fundamental flows namely Couette and Generalized Couette flow. The effects of emerging parameters are discussed through graphs. The convergence of the HAM solution has been discussed by plotting h-curves.

  15. Scattering Characteristics of Discontinuities in a Coaxial Waveguide Partially Filled With Chiral Media

    Institute of Scientific and Technical Information of China (English)

    DONGJianfeng; Jianfeng; XuShanjia

    2003-01-01

    The reflection and transmission character-istics of a coaxial waveguide partially filled with a two layer chiral medium are investigated using a method which com-bines the multimode network theory with a rigorous mode matching procedure. Equivalent radial transmission lines in the transverse cross section and multimode transmission lines in the longitudinal direction are introduced. The for-mulas of the reflection and transmission coefficient matrix are derived. The numerical results show that the chiral-ity and permittivity of the filled materials have significant influence on the reflection and transmission characteristics.

  16. Coaxial fiber supercapacitor using all-carbon material electrodes.

    Science.gov (United States)

    Le, Viet Thong; Kim, Heetae; Ghosh, Arunabha; Kim, Jaesu; Chang, Jian; Vu, Quoc An; Pham, Duy Tho; Lee, Ju-Hyuck; Kim, Sang-Woo; Lee, Young Hee

    2013-07-23

    We report a coaxial fiber supercapacitor, which consists of carbon microfiber bundles coated with multiwalled carbon nanotubes as a core electrode and carbon nanofiber paper as an outer electrode. The ratio of electrode volumes was determined by a half-cell test of each electrode. The capacitance reached 6.3 mF cm(-1) (86.8 mF cm(-2)) at a core electrode diameter of 230 μm and the measured energy density was 0.7 μWh cm(-1) (9.8 μWh cm(-2)) at a power density of 13.7 μW cm(-1) (189.4 μW cm(-2)), which were much higher than the previous reports. The change in the cyclic voltammetry characteristics was negligible at 180° bending, with excellent cycling performance. The high capacitance, high energy density, and power density of the coaxial fiber supercapacitor are attributed to not only high effective surface area due to its coaxial structure and bundle of the core electrode, but also all-carbon materials electrodes which have high conductivity. Our coaxial fiber supercapacitor can promote the development of textile electronics in near future.

  17. An Eigencurrent Approach for the Analysis of Leaky Coaxial Cables

    NARCIS (Netherlands)

    Addamo, G.; Bekers, D.J.; Tijhuis, A.G.; Hon, B.P. de; Orta, R.; Tascone, R.

    2006-01-01

    An eigencurrent approach for the analysis of Leaky Coaxial Cables (LCX) is developed in this work. It is based on the determination of approximate eigenvalues and eigenfunctions of the integral operator of the scattering problem. Numerical results show that a CPU-time saving with respect to a full w

  18. Monitoring Coaxial-Probe Contact Force for Dielectric Properties Measurement

    Science.gov (United States)

    A means is described for measuring and monitoring the contact force applied to a material sample with an open-ended coaxial-line probe for purposes of measuring the dielectric properties of semisolid material samples such as fruit, vegetable and animal tissues. The equipment consists of a stainless...

  19. Vorticity and non-coaxiality in progressive deformations

    NARCIS (Netherlands)

    Means, W.D.; Hobbs, B.E.; Lister, G.S.; Williams, P.F.

    1980-01-01

    A measure of the non-coaxiality involved in progressive deformation histories is proposed in the form of the kinematical vorticity number, Wk. This number is a measure of the relative effects of rotation of material lines (relative to the instantaneous stretching axes) and of stretching of these mat

  20. Review of Combustion Stability Characteristics of Swirl Coaxial Element Injectors

    Science.gov (United States)

    Hulka, J. R.; Casiano, M. J.

    2013-01-01

    Liquid propellant rocket engine injectors using coaxial elements where the center liquid is swirled have become more common in the United States over the past several decades, although primarily for technology or advanced development programs. Currently, only one flight engine operates with this element type in the United States (the RL10 engine), while the element type is very common in Russian (and ex-Soviet) liquid propellant rocket engines. In the United States, the understanding of combustion stability characteristics of swirl coaxial element injectors is still very limited, despite the influx of experimental and theoretical information from Russia. The empirical and theoretical understanding is much less advanced than for the other prevalent liquid propellant rocket injector element types, the shear coaxial and like-on-like paired doublet. This paper compiles, compares and explores the combustion stability characteristics of swirl coaxial element injectors tested in the United States, dating back to J-2 and RL-10 development, and extending to very recent programs at the NASA MSFC using liquid oxygen and liquid methane and kerosene propellants. Included in this study are several other relatively recent design and test programs, including the Space Transportation Main Engine (STME), COBRA, J-2X, and the Common Extensible Cryogenic Engine (CECE). A presentation of the basic data characteristics is included, followed by an evaluation by several analysis techniques, including those included in Rocket Combustor Interactive Design and Analysis Computer Program (ROCCID), and methodologies described by Hewitt and Bazarov.

  1. Evaluating efficiency of coaxial MLC VMAT plan for spine SBRT

    Energy Technology Data Exchange (ETDEWEB)

    Son, Sang Jun; Mun, Jun Ki; Kim, Dae Ho; Yoo, Suk Hyun [Dept. of Radiation Oncology, Seoul National University Hospital, Seoul (Korea, Republic of)

    2014-12-15

    The purpose of the study is to evaluate the efficiency of Coaxial MLC VMAT plan (Using 273° and 350° collimator angle) That the leaf motion direction aligned with axis of OAR (Organ at risk, It means spinal cord or cauda equine in this study.) compare to Universal MLC VMAT plan (using 30° and 330 ° collimator angle) for spine SBRT. The 10 cases of spine SBRT that treated with VMAT planned by Coaxial MLC and Varian TBX were enrolled. Those cases were planned by Eclipse (Ver. 10.0.42, Varian, USA), PRO3 (Progressive Resolution Optimizer 10.0.28) and AAA (Anisotropic Analytic Algorithm Ver. 10.0.28) with coplanar 260 ° arcs and 10MV FFF (Flattening filter free). Each arc has 273° and 350 ° collimator angle, respectively. The Universal MLC VMAT plans are based on existing treatment plans. Those plans have the same parameters of existing treatment plans but collimator angle. To minimize the dose difference that shows up randomly on optimizing, all plans were optimized and calculated twice respectively. The calculation grid is 0.2 cm and all plans were normalized to the target V100%=90%. The indexes of evaluation are V10Gy, D0.03cc, Dmean of OAR (Organ at risk, It means spinal cord or cauda equine in this study.), H.I (Homogeneity index) of the target and total MU. All Coaxial VMAT plans were verified by gamma test with Mapcheck2 (Sun Nuclear Co., USA), Mapphan (Sun Nuclear Co., USA) and SNC patient (Sun Nuclear Co., USA Ver 6.1.2.18513). The difference between the coaxial and the universal VMAT plans are follow. The coaxial VMAT plan is better in the V10Gy of OAR, Up to 4.1%, at least 0.4%, the average difference was 1.9% and In the D0.03cc of OAR, Up to 83.6 cGy, at least 2.2 cGy, the average difference was 33.3 cGy. In Dmean, Up to 34.8 cGy, at least -13.0 cGy, the average difference was 9.6 cGy that say the coaxial VMAT plans are better except few cases. H.I difference Up to 0.04, at least 0.01, the average difference was 0.02 and the difference of average

  2. Forecasting of Corrosion Properties of Steel Wires for Production of Guide Wires for Cardiological Treatment

    Directory of Open Access Journals (Sweden)

    J. Przondziono

    2013-01-01

    Full Text Available The study presents evaluation of the influence of strain in drawing process and of surface modification on resistance to electrochemical corrosion of wires made of stainless steel for production of guide wires used in invasive cardiology. The results of static tensile test enabled us to determine the course of flow curve of wires made of X10CrNi 18-8 steel as well as mathematical form of flow stress function. Resistance to electrochemical corrosion was evaluated on the ground of registered anodic polarisation curves by means of potentiodynamic method. The tests were performed in solution simulating human blood on samples that were electrolytically polished and samples that were polished and then chemically passivated. Exemplary anodic polarisation curves were given. It was proved that with the applied strain, corrosion properties decrease. It was found that chemical passivation improves wire corrosion characteristics. Statistical analysis showed that there is a significant dependence between corrosion properties (polarisation resistance Rp and strain ε applied in drawing process. Functions that present the change Rp=f(ε were selected. The issue is of importance to guide wire manufacturers because application of the suggested methodology will enable us to forecast corrosion characteristics of wire with the required strength drawn with the applied strain.

  3. Wired to freedom

    DEFF Research Database (Denmark)

    Jepsen, Kim Sune Karrasch; Bertilsson, Margareta

    2017-01-01

    of cochlear implantations among Danish users in order to shed more light on their social and political implications. We situate cochlear implantation in a framework of new life science advances, politics, and user experiences. Analytically, we draw upon the notion of social imaginary and explore the social...... dimension of life science through a notion of public politics adopted from the political theory of John Dewey. We show how cochlear implantation engages different social imaginaries on the collective and individual levels and we suggest that users share an imaginary of being “wired to freedom” that involves...... new access to social life, continuous communicative challenges, common practices, and experiences. In looking at their lives as “wired to freedom,” we hope to promote a wider spectrum of civic participation in the benefit of future life science developments within and beyond the field of Cochlear...

  4. From Wires to Cosmology

    CERN Document Server

    Amin, Mustafa A

    2015-01-01

    We provide a statistical framework for characterizing stochastic particle production in the early universe via a precise correspondence to current conduction in wires with impurities. Our approach is particularly useful when the microphysics is uncertain and the dynamics are complex, but only coarse-grained information is of interest. We study scenarios with multiple interacting fields and derive the evolution of the particle occupation numbers from a Fokker-Planck equation. At late times, the typical occupation numbers grow exponentially which is the analog of Anderson localization for disordered wires. Some statistical features of the occupation numbers show hints of universality in the limit of a large number of interactions and/or a large number of fields. For test cases, excellent agreement is found between our analytic results and numerical simulations.

  5. Twisting wire scanner

    CERN Document Server

    Gharibyan, V; Krouptchenkov, I; Nölle, D; Tiessen, H; Werner, M; Wittenburg, K

    2012-01-01

    A new type of 'two-in-one' wire scanner is proposed. Recent advances in linear motors' technology make it possible to combine translational and rotational movements. This will allow to scan the beam in two perpendicular directions using a single driving motor and a special fork attached to it. Vertical or horizontal mounting will help to escape problems associated with the 45 deg scanners. Test results of the translational part with linear motors is presented.

  6. Reusable Hot-Wire Cable Cutter

    Science.gov (United States)

    Pauken, Michael T.; Steinkraus, Joel M.

    2010-01-01

    During the early development stage of balloon deployment systems for missions, nichrome wire cable cutters were often used in place of pyro-actuated cutters. Typically, a nichrome wire is wrapped around a bundle of polymer cables with a low melting point and connected to a relay-actuated electric circuit. The heat from the nichrome reduces the strength of the cable bundle, which quickly breaks under a mechanical load and can thus be used as a release mechanism for a deployment system. However, the use of hand-made heated nichrome wire for cutters is not very reliable. Often, the wrapped nichrome wire does not cut through the cable because it either pulls away from its power source or does not stay in contact with the cable being cut. Because nichrome is not readily soldered to copper wire, unreliable mechanical crimps are often made to connect the nichrome to an electric circuit. A self-contained device that is reusable and reliable was developed to sever cables for device release or deployment. The nichrome wire in this new device is housed within an enclosure to prevent it from being damaged by handling. The electric power leads are internally connected within the unit to the nichrome wire using a screw terminal connection. A bayonet plug, a quick and secure method of connecting the cutter to the power source, is used to connect the cutter to the power leads similar to those used in pyro-cutter devices. A small ceramic tube [0.25-in. wide 0.5-in. long (.6.4-mm wide 13-mm long)] houses a spiraled nichrome wire that is heated when a cable release action is required. The wire is formed into a spiral coil by wrapping it around a mandrel. It is then laid inside the ceramic tube so that it fits closely to the inner surface of the tube. The ceramic tube provides some thermal and electrical insulation so that most of the heat generated by the wire is directed toward the cable bundle in the center of the spiral. The ceramic tube is cemented into an aluminum block, which

  7. Freestanding manganese dioxide nanosheet network grown on nickel/polyvinylidene fluoride coaxial fiber membrane as anode materials for high performance lithium ion batteries

    Science.gov (United States)

    Zhang, Yan; Luo, Zhongping; Xiao, Qizhen; Sun, Tianlei; Lei, Gangtie; Li, Zhaohui; Li, Xiaojing

    2015-11-01

    A novel manganese dioxide (MnO2) nanosheet network grown on nickel/polyvinylidene fluoride (Ni/PVDF) coaxial fiber membrane is successfully fabricated by a three-step route: the polyvinylidene fluoride fiber membrane is prepared by electrospinning method, and then the Ni(shell)/PVDF(core) coaxial fiber membrane with core-shell structure can be obtained by the electroless deposition, and finally the manganese dioxide nanosheet network grown on Ni/PVDF coaxial fiber membrane can be achieved by using a simple hydrothermal treatment. This as-prepared binder-free and flexible composite membrane is directly used as anode for lithium ion batteries. The excellent electrochemical performance of the composite membrane can be attributed to the unique combinative effects of nanosized MnO2 network and conductive Ni/PVDF fiber matrix as well as the porous structure of composite fiber membrane.

  8. Control of physical properties of carbon nanofibers obtained from coaxial electrospinning of PMMA and PAN with adjustable inner/outer nozzle-ends.

    Science.gov (United States)

    Kaerkitcha, Navaporn; Chuangchote, Surawut; Sagawa, Takashi

    2016-12-01

    Hollow carbon nanofibers (HCNFs) were prepared by electrospinning method with several coaxial nozzles, in which the level of the inner nozzle-end is adjustable. Core/shell nanofibers were prepared from poly(methyl methacrylate) (PMMA) as a pyrolytic core and polyacrylonitrile (PAN) as a carbon shell with three types of normal (viz. inner and outer nozzle-ends are balanced in the same level), inward, and outward coaxial nozzles. The influence of the applied voltage on these three types of coaxial nozzles was studied. Specific surface area, pore size diameter, crystallinity, and degree of graphitization of the hollow and mesoporous structures of carbon nanofibers obtained after carbonization of the as spun PMMA/PAN nanofibers were characterized by BET analyses, X-ray diffraction, and Raman spectroscopy in addition to the conductivity measurements. It was found that specific surface area, crystallinity, and graphitization degree of the HCNFs affect the electrical conductivity of the carbon nanofibers.

  9. Magnetoconductance of quantum wires

    Science.gov (United States)

    Ferreira, Gerson J.; Sammarco, Filipe; Egues, Carlos

    2010-03-01

    At low temperatures the conductance of a quantum wires exhibit characteristic plate-aus due to the quantization of the transverse modes [1]. In the presence of high in-plane magnetic fields these spin-split transverse modes cross. Recently, these crossings were observed experimentally [2] via measurements of the differential conductance as a function of the gate voltage and the in-plane magnetic-field. These show structures described as either anti-crossings or magnetic phase transitions. Motivated by our previous works on magnetotransport in 2DEGs via the Spin Density Functional Theory (SDFT) [3], here we propose a similar model to investigate the magnetoconductance of quantum wires. We use (i) the SDFT via the Kohn-Sham self-consistent scheme within the local spin density approximation to obtain the electronic structure and (ii) the Landauer-Buettiker formalism to calculate the conductance of a quantum wire. Our results show qualitative agreement with the data of Ref. [2]. [1] B. J. van Wees et al., Phys. Rev. Lett. 60, 848 (1988). [2] A. C. Graham et al., Phys. Rev. Lett. 100, 226804 (2008). [3] H. J. P. Freire, and J. C. Egues, Phys. Rev. Lett. 99, 026801 (2007); G. J. Ferreira, and J. Carlos Egues, J. Supercond. Nov. Mag., in press; G. J. Ferreira, H. J. P. Freire, J. Carlos Egues, submitted.

  10. Tuning a Tetrahertz Wire Laser

    Science.gov (United States)

    Qin, Qi; Williams, Benjamin S.; Kumar, Sushil; Reno, John L.; Hu, Qing

    2009-01-01

    Tunable terahertz lasers are desirable in applications in sensing and spectroscopy because many biochemical species have strong spectral fingerprints at terahertz frequencies. Conventionally, the frequency of a laser is tuned in a similar manner to a stringed musical instrument, in which pitch is varied by changing the length of the string (the longitudinal component of the wave vector) and/ or its tension (the refractive index). However, such methods are difficult to implement in terahertz semiconductor lasers because of their poor outcoupling efficiencies. Here, we demonstrate a novel tuning mechanism based on a unique 'wire laser' device for which the transverse dimension w is much much less than lambda. Placing a movable object close to the wire laser manipulates a large fraction of the waveguided mode propagating outside the cavity, thereby tuning its resonant frequency. Continuous single-mode redshift and blueshift tuning is demonstrated for the same device by using either a dielectric or metallic movable object. In combination, this enables a frequency tuning of approximately equal to 137 GHz (3.6%) from a single laser device at approximately equal to 3.8 THz.

  11. 75 FR 65052 - Consensus Standards, Standard Practice for Maintenance of Airplane Electrical Wiring Systems

    Science.gov (United States)

    2010-10-21

    ... Practice for Maintenance of Airplane Electrical Wiring Systems (Standard Practice) as an acceptable means... FAA finds the standards to be acceptable methods and procedures for maintenance of electrical wiring... Practice for Maintenance of Airplane Electrical Wiring Systems. FOR FURTHER INFORMATION CONTACT:...

  12. 线切割自动编程中刀补方向的确定方法%The Method of Tool Compensation Direction Calculation in Wire Cutting Automatic Programming

    Institute of Scientific and Technical Information of China (English)

    莫秀波; 张秋菊

    2013-01-01

    In order to improve the wire cutting automatic programming system and simplify the operation process , it puts forward a automatic judgment tool compensation direction method based on a set of process parameters and processing conditions in the wire cutting tool path generation .This method does not need a manually tool direc-tion definition , effectively improves the efficiency of programming and avoids human error .%为了提高线切割自动编程系统的自动化程度,减少操作步骤,根据生成线切割刀补轨迹所需设定的工艺参数与加工条件,提出了一种可以自动判断刀补方向的方法,自动编程系统应用该方法后无需人工设定刀补方向,可有效提高编程效率,避免人为出错。

  13. Durability to Electromigration of an Annealing-Twinned Ag-4Pd Alloy Wire Under Current Stressing

    Science.gov (United States)

    Chuang, Tung-Han; Lin, Hsin-Jung; Chuang, Chien-Hsun; Tsai, Chih-Hsin; Lee, Jun-Der; Tsai, Hsing-Hua

    2014-11-01

    Ag-4Pd binary alloy wire has been produced as an alternative to a previously developed Ag-8Au-3Pd ternary alloy wire to meet requirements for high electrical conductivity and low cost. The electrical resistivity of this Ag-4Pd bonding wire, manufactured with a conventional method, is 3.7 μΩ cm, close to the values of traditional 3N Au wire (3.5 μΩ cm) and Pd-coated Cu wire (1.8 μΩ cm). To further improve the performance of this bonding wire, a large amount of annealing twins were introduced in this Ag-4Pd alloy wire through an innovative concept of sequential drawing and multiple annealing processes. The resulting electrical resistivity of this annealing-twinned Ag-4Pd wire is 3.5 μΩ cm. In contrast to the apparent increase in grain size in the conventional Ag-4Pd wire under electrical stressing with a current density of 1.23 × 105 A/cm2 for various times, the grains in this annealing-twinned wire grow much more slowly. The breaking load and elongation of this annealing-twinned Ag-4Pd wire are also higher than those of conventional wire. Furthermore, annealing twins increase the durability to electromigration of this Ag-4Pd wire under electrical stressing with various current densities.

  14. Metering Wheel-Wire Track Wire Boom Deployment Mechanism

    Science.gov (United States)

    Granoff, Mark S.

    2014-01-01

    The NASA MMS Spin Plane Double Probe (SDP) Deployer utilizes a helical path, rotating Metering Wheel and a spring loaded Wire "Holding" Track to pay out a "fixed end" 57 meter x 1.5 mm diameter Wire Boom stored between concentric storage cylinders. Unlike rotating spool type storage devices, the storage cylinders remain stationary, and the boom wire is uncoiled along the length of the cylinder via the rotation of the Metering Wheel. This uncoiling action avoids the need for slip-ring contacts since the ends of the wire can remain stationary. Conventional fixed electrical connectors (Micro-D type) are used to terminate to operational electronics.

  15. Prime wires for ATLAS

    CERN Multimedia

    2003-01-01

    In an award ceremony on 3 September, ATLAS honoured the French company Axon Cable for its special coaxial cables, which were purpose-built for the Liquid Argon calorimeter modules. Working for CERN since the 1970s, Axon' Cable received the ATLAS supplier award last week for its contribution to the liquid argon calorimeter cables of ATLAS (LAL/Orsay, France and University of Victoria, Canada), started in 1996. Its two sets of minicoaxial cables, called harnesses "A" and "B", are designed to function in the harsh conditions in the liquid argon (at 90 Kelvin or -183°C) and under extreme radiation (up to several Mrads). The cables are mainly used for the readout of the calorimeters, and are connected to the outside world by 114 signal feedthroughs with 1920 channels each. The signal from the detectors is transmitted directly without any amplification, which imposes tight restrictions on the impedance and on the signal propagation time of the cables. Peter Jenni, ATLAS spokesperson, gives the award for best s...

  16. NUMERICLA SIMULATION ON DEFORMATION CHARACTERISTICS OF AS WIRE BY CAWTEX

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Castex(continuous cast and extrusion)is a latest metallurgical technology. Making of AS wire(aluminum-clad steel wire) by Castex is an advanced bonding technology of bimetal. In order to study the deformation character of AS wire the numerical simulation is performed with FE method. From the simulation result the following conclusions are obtained:① The simulation is carried out sequentially in three zones:initial extrusion,cavity-filling and bonding.② In the first zone the shearing deformation governs the whole zone,while in that of cavity-filling, the deformation mainly concentrates on transition arc of the concave mould. In addition, in the last zone, the dominant deformation lies at the boundary of concave mould, surface of steel wire and entry of sizing band. Due to the movement of steel wire, the direction of shear stress on its surface is opposite to that on the boundary of concave die.

  17. Controlled electromigration and oxidation of free-standing copper wires

    Science.gov (United States)

    Hauser, J. S.; Schwichtenberg, J.; Marz, M.; Sürgers, C.; Seiler, A.; Gerhards, U.; Messerschmidt, F.; Hensel, A.; Dittmeyer, R.; Löhneysen, H. v.; Hoffmann-Vogel, R.

    2016-12-01

    We have studied controlled electromigration (EM) in free-standing copper wires. Besides electrical characterization by voltage-current measurements, structural analyses have been performed by means of scanning electron microscopy and cross-sectional microprobe measurements. We have found that oxidation during the EM in air stabilizes the free-standing wire against uncontrolled blowing, making it possible to thin the conductive part of the wire down to a conductance of a few conductance quanta G_0=2e^2{/}h. The decisive influence of oxidation by air on the EM process was confirmed by control experiments performed under ultra-high vacuum conditions. In line with these findings, free-standing Au wires were difficult to thin down reproducibly to a conductance of a few G_0. Estimates of the local temperature in the free-standing wire are obtained from finite element method calculations.

  18. Permanent wire splicing by an explosive joining process

    Science.gov (United States)

    Bement, Laurence J.; Kushnick, Anne C.

    1991-11-01

    The invention is an apparatus and method for wire splicing using an explosive joining process. The apparatus consists of a prebent, U-shaped strap of metal that slides over prepositioned wires. A standoff means separates the wires from the strap before joining. An adhesive means holds two ribbon explosives in position centered over the U-shaped strap. A detonating means connects to the ribbon explosives. The process involves spreading strands of each wire to be joined into a flat plane. The process then requires alternating each strand in alignment to form a mesh-like arrangement with an overlapped area. The strap slides over the strands of the wires, and the standoff means is positioned between the two surfaces. The detonating means then initiates the ribbon explosives that drive the strap to accomplish a high velocity, angular collision between the mating surfaces. This collision creates surface melts and collision bonding results in electron sharing linkups.

  19. Thermal Model of a Current-Carrying Wire in a Vacuum

    Science.gov (United States)

    Border, James

    2006-01-01

    A computer program implements a thermal model of an insulated wire carrying electric current and surrounded by a vacuum. The model includes the effects of Joule heating, conduction of heat along the wire, and radiation of heat from the outer surface of the insulation on the wire. The model takes account of the temperature dependences of the thermal and electrical properties of the wire, the emissivity of the insulation, and the possibility that not only can temperature vary along the wire but, in addition, the ends of the wire can be thermally grounded at different temperatures. The resulting second-order differential equation for the steady-state temperature as a function of position along the wire is highly nonlinear. The wire is discretized along its length, and the equation is solved numerically by use of an iterative algorithm that utilizes a multidimensional version of the Newton-Raphson method.

  20. THERMAL CONDUCTIVITY OF METALLIC WIRES

    Institute of Scientific and Technical Information of China (English)

    LU XIANG; GU JI-HUA; CHU JUN-HAO

    2001-01-01

    The effect of radial thickness on the thermal conductivity of a free standing wire is investigated. The thermal conductivity is evaluated using the Boltzmann equation. A simple expression for the reduction in conductivity due to the increase of boundary scattering is presented. A comparison is made between the experimental results of indium wires and the theoretical calculations. It is shown that this decrease of conductivity in wires is smaller than that in film where heat flux is perpendicular to the surface.

  1. COMPARATIVE ANALYSIS OF THE BEHAVIOR OF COAXIAL AND FRONTAL COUPLINGS – WITH PERMANENT MAGNETS – IN HIGH TEMPERATURE ENVIRONMENTS

    Directory of Open Access Journals (Sweden)

    Marcel Oanca

    2004-12-01

    Full Text Available This paper presents a comparative analysis of the behavior of coaxial and frontal couplings – with permanent magnets – in high temperature environments specific to iron and steel industry. The comparative analysis is made at the level of the specific forces developed in the most difficult environments. The maximum temperature was limited for reasons of thermal stability of the Nd-Fe-B permanent magnets. In this context it was studied, by the help of the PDE-ase soft that uses the finite element method, the way magnetic induction modifies, the specific forces developed and the distribution of temperature within the coaxial and frontal couplers with permanent magnets, for variations of the distance between the magnets (air gap within the limits 2-20 mm.

  2. Ultra-high throughput synthesis of nanoparticles with homogeneous size distribution using a coaxial turbulent jet mixer.

    Science.gov (United States)

    Lim, Jong-Min; Swami, Archana; Gilson, Laura M; Chopra, Sunandini; Choi, Sungyoung; Wu, Jun; Langer, Robert; Karnik, Rohit; Farokhzad, Omid C

    2014-06-24

    High-throughput production of nanoparticles (NPs) with controlled quality is critical for their clinical translation into effective nanomedicines for diagnostics and therapeutics. Here we report a simple and versatile coaxial turbulent jet mixer that can synthesize a variety of NPs at high throughput up to 3 kg/d, while maintaining the advantages of homogeneity, reproducibility, and tunability that are normally accessible only in specialized microscale mixing devices. The device fabrication does not require specialized machining and is easy to operate. As one example, we show reproducible, high-throughput formulation of siRNA-polyelectrolyte polyplex NPs that exhibit effective gene knockdown but exhibit significant dependence on batch size when formulated using conventional methods. The coaxial turbulent jet mixer can accelerate the development of nanomedicines by providing a robust and versatile platform for preparation of NPs at throughputs suitable for in vivo studies, clinical trials, and industrial-scale production.

  3. Flux amplification and sustainment of ST plasmas by multi-pulsed coaxial helicity injection on HIST

    Science.gov (United States)

    Higashi, T.; Ishihara, M.; Kikuchi, Y.; Fukumoto, N.; Nagata, M.

    2010-11-01

    The Helicity Injected Spherical Torus (HIST) device has been developed towards high-current start up and sustainment by Multi-pulsed Coaxial Helicity Injection (M-CHI) method. Multiple pulses operation of the coaxial plasma gun can build the magnetic field of STs and spheromak plasmas in a stepwise manner. So far, successive gun pulses on SSPX at LLNL were demonstrated to maintain the magnetic field of spheromak in a quasi-steady state against resistive decay [1]. The resistive 3D-MHD numerical simulation [2] for STs reproduced the current amplification by the M-CHI method and confirmed that stochastic magnetic field was reduced during the decay phase. By double pulsed operation on HIST, the plasma current was effectively amplified against the resistive decay. The life time increases up to 10 ms which is longer than that in the single CHI case (4 ms). The edge poloidal fields last between 0.5 ms and 6 ms like a repetitive manner. During the second driven phase, the toroidal ion flow is driven in the same direction as the plasma current as well as in the initial driven phase. At the meeting, we will discuss a current amplification mechanism based on the merging process with the plasmoid injected secondly from the gun. [1] B. Hudson et al., Phys. Plasmas Vol.15, 056112 (2008). [2] Y. Kagei et al., J. Plasma Fusion Res. Vol.79, 217 (2003).

  4. Measuring concentricity and coaxial tolerance of nozzle and cavity with tool microscope

    Science.gov (United States)

    Lu, Xizhao; Jiang, Feng; Ye, Ruifang; Lei, Tingping

    2016-01-01

    While the equipment of Micro-jet wave-guided laser was assembled, high-precision of concentricity and coaxiality between nozzle and cavity are required, which directly or indirectly influent the laser coupling precision of nozzle, the micro-jet stability and the steady length of micro-jet as well. As a result, the measurement of concentricity and coaxiality is important to improve the processing quality of Micro-jet wave-guided laser Through the new digital universal tool microscope measuring both ends of micro nozzle and diameter of nozzle, more resolution the other hand, the backlight detection the edge of nozzle is utilized. When the position of the center of a circle is indirect measured and then find out the concentricity through the uncertainty of the measurement and calculation method. V shaped groove is utilized to make certain its position. Otherwise, digital imaging through setting fixture and the use of new digital universal tool microscope and processed by software, which will cause to reduce measurement human error in tradition, after that, error theory analysis will be carried out, uncertainty theory will be utilized to make the experiment more sure at the same time. Above all, the reliability of data is obtained, compared with the traditional measurement methods are more accurate. Therefore, the processing quality of laser drilling will be enhanced significantly.

  5. Subminiature Hot-Wire Probes

    Science.gov (United States)

    Westphal, R. V.; Lemos, F. R.; Ligrani, P. M.

    1989-01-01

    Class of improved subminiature hot-wire flow-measuring probes developed. Smaller sizes yield improved resolution in measurements of practical aerodynamic flows. Probe made in one-wire, two-perpendicular-wire, and three-perpendicular-wire version for measurement of one, two, or all three components of flow. Oriented and positioned on micromanipulator stage and viewed under microscope during fabrication. Tested by taking measurements in constant-pressure turbulent boundary layer. New probes give improved measurements of turbulence quantities near surfaces and anisotropies of flows strongly influence relative errors caused by phenomena related to spatial resolution.

  6. Plasma Formation Around Single Wires

    Science.gov (United States)

    Duselis, Peter U.; Kusse, Bruce R.

    2002-12-01

    At Cornell's Laboratory of Plasma Studies, single wires of various metals were exploded using a ˜250 ns pulser with a rise time of ˜20 A/ns. It was found that the wires first experience a resistive heating phase that lasts 50-80 ns before a rapid collapse of voltage. From that point on, the voltage across the wire was negligible while the current through the wire continued to increase. We attribute this voltage collapse to the formation of plasma about the wire. Further confirmation of this explanation will be presented along with new experimental data describing preliminary spectroscopy results, the expansion rate of the plasma, and current flow along the wire as a function of radius. The resistance of the wire-electrode connection will be shown to significantly affect the energy deposition. Various diagnostics were used to obtain these experiments. Ultraviolet sensitive vacuum photodiodes and a framing camera with an 8 ns shutter were used to detect and measure the width of the visible light emitted by the plasma. A special wire holder was constructed that allowed the transfer of current from the wire to the surrounding plasma to be observed.

  7. Wiring regulations in brief

    CERN Document Server

    Tricker, Ray

    2012-01-01

    Tired of trawling through the Wiring Regs?Perplexed by Part P?Confused by cables, conductors and circuits?Then look no further! This handy guide provides an on-the-job reference source for Electricians, Designers, Service Engineers, Inspectors, Builders, Students, DIY enthusiastsTopic-based chapters link areas of working practice - such as cables, installations, testing and inspection, special locations - with the specifics of the Regulations themselves. This allows quick and easy identification of the official requirements relating to the situati

  8. The behavior of concrete cylinders confined by shape memory alloy wires

    Science.gov (United States)

    Choi, Eunsoo; Nam, Tae-hyun; Cho, Sung-Chul; Chung, Young-Soo; Park, Taehyo

    2008-12-01

    The purpose of this study was to propose a new method to confine concrete cylinders or reinforced concrete columns using martensitic or austenitic shape memory alloy (SMA) wires. The prestrained martensitic SMA wire was wrapped around a concrete cylinder then heated by a heating jacket. In the process, the confining stress around the cylinder was developed in the SMA wire due to the shape memory effect, which can increase the strength and ductility of the cylinder under axial compressive load. For austenitic shape memory wires, the wires were prestrained as they were wrapped around the concrete cylinders on which post-tensioning stress was generated. In this study, martensitic and austenitic SMA wires of 1.0 mm in diameter were used for the confinement. Recovery tests were conducted on the martensitic wire to assess the recovery stress. Also, a superelastic behavior test was performed for the austenitic wire. The confinement by martensitic SMA wires increased the strength slightly and greatly increased the ductility compared to the strength and ductility of plain concrete cylinders. The austenitic SMA wires showed a similar effect on concrete cylinders to that of the martensitic wires. This study showed the potential of the SMA wire jacketing method to retrofit reinforced concrete columns and protect them from seismic risks.

  9. Study of a coaxial thermoacoustic-Stirling cooler

    Science.gov (United States)

    Tijani, M. E. H.; Spoelstra, S.

    2008-01-01

    A coaxial thermoacoustic-Stirling cooler is built and performance measurements are performed. The cooler uses the acoustic power produced by a linear motor to pump heat through a regenerator from a cold heat exchanger to an ambient one. The cooler incorporates a compact acoustic network to create the traveling-wave phasing necessary for the operation in a Stirling cycle. The network has a coaxial geometry instead of the toroidal one usually used in such systems. The design, construction and performance measurements of the cooler are presented. A measured coefficient of performance relative to Carnot of 25% and a low temperature of -54 °C are achieved by the cooler. This efficiency surpasses the performance of the most efficient standing-wave cooler by almost a factor of two.

  10. Study of a coaxial thermoacoustic-Stirling cooler

    Energy Technology Data Exchange (ETDEWEB)

    Spoelstra, S.; Tijani, M.E.H. [ECN Energy Efficiency in the Industry, Petten (Netherlands)

    2008-05-15

    A coaxial thermoacoustic-Stirling cooler is built and performance measurements are performed. The cooler uses the acoustic power produced by a linear motor to pump heat through a regenerator from a cold heat exchanger to an ambient one. The cooler incorporates a compact acoustic network to create the traveling-wave phasing necessary for the operation in a Stirling cycle. The network has a coaxial geometry instead of the toroidal one usually used in such systems. The design, construction and performance measurements of the cooler are presented. A measured coefficient of performance relative to Carnot of 25% and a low temperature of -54 degrees C are achieved by the cooler. This efficiency surpasses the performance of the most efficient standing-wave cooler by almost a factor of two.

  11. Raman free-electron laser with a coaxial wiggler

    Science.gov (United States)

    Farokhi, B.; Maraghechi, B.; Willett, J. E.

    2000-10-01

    A one-dimensional theory of the stimulated Raman scattering mechanism for a coaxial free-electron laser (FEL) is developed. The beam-frame FEL dispersion relation and a formula for the lab-frame spatial growth rate are derived. A numerical study of the growth rate for the coaxial wiggler is made and compared with that for the helical wiggler. Except for a part of the group II orbits, the growth rate is found to be less than the helical wiggler. Relativistic effects due to the transverse oscillation of electrons in the wiggler field prevent the FEL operation from approaching magnetoresonance. In the absence of these relativistic mass effects, the calculations show a magnetoresonance associated with the first spatial harmonic and a much narrower resonance at the third spatial harmonic.

  12. Characterization of coaxial rocket injector sprays under high pressure environments

    Science.gov (United States)

    Sankar, S. V.; Wang, G.; Brena De La Rosa, A.; Rudoff, R. C.; Isakovic, A.; Bachalo, W. D.

    1992-01-01

    The effect of elevated environment pressures on the atomization characteristics of a single element, scaled-down, shear-coaxial rocket injector has been investigated. In this study, the shear coaxial injector was operated with water and air as simulants for conventionally used liquid oxygen and hydrogen gas, respectively. The experiments were conducted in a specially designed high pressure rig. A two-component PDPA/DSA system was used to study the spray characteristics at different chamber pressures ranging from atmospheric to 100 psig. The study showed an overall increase in the droplet sizes at higher chamber pressures. This phenomenon is attributed to a decrease in the secondary atomization effects at higher chamber pressures which, in turn, is directly related to a decrease in the shear experienced by the droplets as they move axially through the pressure chamber.

  13. COAXIAL TWO-CHANNEL DIELECTRIC WAKE FIELD ACCELERATOR

    Energy Technology Data Exchange (ETDEWEB)

    Hirshfield, Jay L. [Omega-P, Inc.

    2013-04-30

    Theory, computations, and experimental apparatus are presented that describe and are intended to confirm novel properties of a coaxial two-channel dielectric wake field accelerator. In this configuration, an annular drive beam in the outer coaxial channel excites multimode wakefields which, in the inner channel, can accelerate a test beam to an energy much higher than the energy of the drive beam. This high transformer ratio is the result of judicious choice of the dielectric structure parameters, and of the phase separation between drive bunches and test bunches. A structure with cm-scale wakefields has been build for tests at the Argonne Wakefield Accelerator Laboratory, and a structure with mm-scale wakefields has been built for tests at the SLAC FACET facility. Both tests await scheduling by the respective facilities.

  14. Phonon spectra in quantum wires

    Directory of Open Access Journals (Sweden)

    Ilić Dušan

    2007-01-01

    Full Text Available Green's function method, adjusted to bound crystalline structures, was applied to obtain the phonon dispersion law in quantum wires. The condition of the existence of small mechanical atom movements defining phonon spectra can be found by solving the secular equation. This problem was presented graphically for different boundary parameters. The presence of boundaries, as well as the change of boundary parameters, leads to the appearance of new properties of the layered structure. The most important feature is that, beside the allowed energy zones (which are continuous as in the bulk structure, zones of forbidden states appear. Different values of the boundary parameters lead to the appearance of lower and upper energy gaps, or dispersion branches spreading out of the bulk energy zone. The spectra of phonons in corresponding unbound structures were correlated to those in bound structures.

  15. Corrosion of Wires on Wooden Wire-Bound Packaging Crates

    Science.gov (United States)

    Samuel L. Zelinka; Stan Lebow

    2015-01-01

    Wire-bound packaging crates are used by the US Army to transport materials. Because these crates may be exposed to harsh environments, they are dip-treated with a wood preservative (biocide treatment). For many years, zinc-naphthenate was the most commonly used preservative for these packaging crates and few corrosion problems with the wires were observed. Recently,...

  16. Coaxial HOM coupler for the 500 MHz RF damped cavity

    CERN Document Server

    Koseki, T; Takahashi, T; Kamiya, Yu; Satoh, K; Ogata, H

    2001-01-01

    We have developed a new higher-order modes (HOMs) coupler of coaxial waveguide type for the 500 MHz damped cavity. An SiC ceramics is adopted as microwave absorber. Two prototype models of the HOM coupler have been fabricated and tested. The detailed design of the coupler is described in this paper. The results of RF characteristics measurement and high power conditioning are also presented.

  17. Plasma gun with coaxial powder feed and adjustable cathode

    Science.gov (United States)

    Zaplatynsky, Isidor (Inventor)

    1991-01-01

    An improved plasma gun coaxially injects particles of ceramic materials having high melting temperatures into the central portion of a plasma jet. This results in a more uniform and higher temperature and velocity distribution of the sprayed particles. The position of the cathode is adjustable to facilitate optimization of the performance of the gun wherein grains of the ceramic material are melted at lower power input levels.

  18. Acoustically Forced Coaxial Hydrogen / Liquid Oxygen Jet Flames

    Science.gov (United States)

    2016-05-15

    visualized for both reacting and nonreacting cases. The jet flame was studied unforced, without acoustics , and forced, with transverse acoustic waves in...liquid rocket injector flames react to acoustic waves . In this study, a representative coaxial gaseous hydrogen / liquid oxygen (LOX) jet flame is...hydrogen / liquid oxygen (LOX) jet flame is visualized for both reacting and nonreacting cases. The jet flame was studied unforced, without acoustics , and

  19. Coaxial Ring Cyclotron as a Perspective Nuclear Power Engineering Machine

    OpenAIRE

    Tumanyan, A. R.; Simonyan, Kh. A.; Mkrtchyan, R. L.; Amatuni, A. Ts.; Avakyan, R. O.; Khudaverdyan, A. G.

    1995-01-01

    The circuit arrangement of the proposed coaxial ring cyclotron (CRC) is described, and its main advantages, such as simple injection technique, several injected beams summation option, high efficiency, are considered. The proposed proton accelerator is a perspective machine for the solution of the main problems of the present day nuclear power engineering as well as for the next-generation nuclear power plants, representing a combination of subcritical reactors and particle accelerators. The ...

  20. 基于遗传算法的栅格天线阵旁瓣电平优化方法%An Optimization Method for Sidelobe Reduction of Wire Grid Array Antenna Using Genetic Algorithm

    Institute of Scientific and Technical Information of China (English)

    郑文超; 郎量; 李青侠; 桂良启

    2011-01-01

    An optimization method which is based on Genetic Algorithm(GA) for sidelobe reduction of wire grid array antenna is proposed.In this method,a model to analyze the far-field of the wire grid array antenna is reported.Current amplitudes which fit the designed sidelobe are obtained by GA.Current amplitudes of each short side are treated as variables and sidelobe level in azimuth plane is treated as fitness function of GA.Then the current amplitudes are used to calculate the impedances of each short side so as to design the array.At last,in order to verify the proposed method,an optimized wire grid array antenna is simulated by the electromagnetic simulating software.A prototype antenna is fabricated and tested.Results show that the sidelobe level has been reduced by 5dB.%在推导出栅格天线阵列方向图的基础上,提出一种基于遗传算法的栅格天线阵旁瓣电平优化的方法。此方法首先简化栅格天线阵物理模型,给出等效模型下的阵列方向图,然后以栅格天线阵的短边电流幅度为优化参量,以阵列天线方位面的副瓣电平为适应度函数,利用遗传算法的最优化搜索得到满足副瓣要求的电流幅度,再通过电流幅度计算辐射单元阻抗,最终设计出满足要求的低旁瓣栅格天线阵。为了验证该方法的有效性,对一种频扫微带栅格天线进行了优化,在电磁仿真软件中对优化后的天线进行了仿真,根据设计结果加工制作了原型天线并进行了测试,测试结果显示优化后天线阵的副瓣电平降低了5dB,优化效果明显。

  1. Engineering design of the PLX- α coaxial gun

    Science.gov (United States)

    Cruz, Edward; Brockington, Samuel; Case, Andrew; Luna, Marco; Witherspoon, Douglas; Langendorf, Samuel

    2016-10-01

    We describe the engineering and technical aspects of the coaxial gun designed for the 60-gun scaling study of spherically imploding plasma liners as a standoff driver for plasma-jet-driven magneto-inertial fusion. Each coaxial gun incorporates a fast, dense gas injection and triggering system, a compact low-weight pfn with integral sparkgap switching, and a contoured gap designed to suppress the blow-by instability. Alpha1 and Alpha2 guns are compared, with emphasis on the improvements on Alpha2, which include a faster more robust gas valve, an improved electrode contour, a custom 600- μF, 5-kV pfn, and a set of six inline sparkgap switches operated in parallel. The switch and pfn configurations are mounted directly to the back of the gun, and are designed to reduce inductance, cost, and complexity, maximize efficiency and system reliability, and ensure symmetric current flow. We will provide a detailed overview of the design choices made for the PLX- α coaxial gun. This work supported by the ARPA-E ALPHA Program.

  2. Analysis and Design Optimization of a Coaxial Surface-Mounted Permanent-Magnet Magnetic Gear

    Directory of Open Access Journals (Sweden)

    Xiaoxu Zhang

    2014-12-01

    Full Text Available This paper presents the analysis and design optimization of a coaxial surface-mounted permanent-magnet magnetic gear. The magnetic field distribution in the coaxial magnetic gear is calculated analytically in the polar coordinate system and then validated by the finite element method (FEM. The analytical field solution allows the prediction of the magnetic torque, which is formulated as a function of design parameters. The impacts of key design parameters on the torque capability are then studied and some significant observations are summarized. Furthermore, the particle swarm optimization (PSO algorithm is employed to optimize the studied magnetic gear. Given that the torque capability and material cost conflict with each other, both of them are set as the optimization objectives in this paper. Different weight factors may be chosen for the two objectives so that more attention can be placed on one or another. The results shows that the highest torque density of 157 kNm/m3 is achieved with the consideration focusing on the torque capability only, then the highest torque per permanent magnet (PM consumption could be improved to 145 Nm/kg by taking the material cost into account. By synthesizing the torque capability and material cost, a 124 kNm/m3 of torque density and a 128 Nm/kg of torque per PM consumption could be achieved simultaneously by the optimal design.

  3. High-Throughput Fabrication of Resonant Metamaterials with Ultrasmall Coaxial Apertures via Atomic Layer Lithography.

    Science.gov (United States)

    Yoo, Daehan; Nguyen, Ngoc-Cuong; Martin-Moreno, Luis; Mohr, Daniel A; Carretero-Palacios, Sol; Shaver, Jonah; Peraire, Jaime; Ebbesen, Thomas W; Oh, Sang-Hyun

    2016-03-09

    We combine atomic layer lithography and glancing-angle ion polishing to create wafer-scale metamaterials composed of dense arrays of ultrasmall coaxial nanocavities in gold films. This new fabrication scheme makes it possible to shrink the diameter and increase the packing density of 2 nm-gap coaxial resonators, an extreme subwavelength structure first manufactured via atomic layer lithography, both by a factor of 100 with respect to previous studies. We demonstrate that the nonpropagating zeroth-order Fabry-Pérot mode, which possesses slow light-like properties at the cutoff resonance, traps infrared light inside 2 nm gaps (gap volume ∼ λ(3)/10(6)). Notably, the annular gaps cover only 3% or less of the metal surface, while open-area normalized transmission is as high as 1700% at the epsilon-near-zero (ENZ) condition. The resulting energy accumulation alongside extraordinary optical transmission can benefit applications in nonlinear optics, optical trapping, and surface-enhanced spectroscopies. Furthermore, because the resonance wavelength is independent of the cavity length and dramatically red shifts as the gap size is reduced, large-area arrays can be constructed with λresonance ≫ period, making this fabrication method ideal for manufacturing resonant metamaterials.

  4. Highly sensitive glucose biosensor based on Au-Ni coaxial nanorod array having high aspect ratio.

    Science.gov (United States)

    Hsu, Che-Wei; Wang, Gou-Jen

    2014-06-15

    An effective glucose biosensor requires a sufficient amount of GOx immobilizing on the electrode surface. An electrode of a 3D nanorod array, having a larger surface-to-volume ratio than a 2D nanostructure, can accommodate more GOx molecules to immobilize onto the surface of the nanorods. In this study, a highly sensitive Au-Ni coaxial nanorod array electrode fabricated through the integration of nano electroforming and immersion gold (IG) method for glucose detection was developed. The average diameter of the as-synthesized Ni nanorods and that of the Au-Ni nanorods were estimated to be 150 and 250 nm, respectively; both had a height of 30 μm. The aspect ratio was 120. Compared to that of a flat Au electrode, the effective sensing area was enhanced by 79.8 folds. Actual glucose detections demonstrated that the proposed Au-Ni coaxial nanorod array electrode could operate in a linear range of 27.5 μM-27.5mM with a detection limit of 5.5μM and a very high sensitivity of 769.6 μA mM(-1)cm(-2). Good selectivity of the proposed sensing device was verified by sequential injections of uric acid (UA) and ascorbic acid (AA). Long-term stability was examined through successive detections over a period of 30 days.

  5. Computer Modeling for Microwave Ablation in Breast Cancer Using a Coaxial Slot Antenna

    Science.gov (United States)

    Cepeda Rubio, Mario Francisco Jesus; Guerrero López, Geshel David; Valdés Perezgasga, Francisco; Flores García, Francisco; Vera Hernández, Arturo; Leija Salas, Lorenzo

    2015-11-01

    The use of breast cancer mammography screening has allowed detection of a greater number of small carcinomas, and this has facilitated treatment by minimally invasive techniques. Microwave energy is a promising alternative treatment because it can preferentially heat and damage high-water-content breast carcinomas. In order to evaluate the feasibility of using this technique to treat breast cancer, a coaxial slot antenna computer simulation based on an axisymmetric finite element method (FEM) model was used to compare heating differences between cancer and normal breast tissue. Three FEM computer models were developed: in one of them, the coaxial slot antenna was immersed only in homogeneous breast tissue; for the second one, the antenna was immersed only in cancer tissue; for the third one, the antenna was inserted into malignant tissue surrounded by breast tissue. According to the results, the computer modeling demonstrated that the difference in dielectric properties and thermal parameters between malignant and normal adipose-dominated tissue was able to cause preferential heating of tumors during microwave ablation. Furthermore, the ablation zone radius was 42 % larger in the tumor than in low-water-content adipose tissue. Even though this technique requires further research, it is a promising minimally invasive modality for the local treatment of breast cancer.

  6. Measurement of Neutrons Produced by Beam-Target Interactions via a Coaxial Plasma Accelerator

    Science.gov (United States)

    Cauble, Scott; Poehlmann, Flavio; Rieker, Gregory; Cappelli, Mark

    2011-10-01

    This poster presents a method to measure neutron yield from a coaxial plasma accelerator. Stored electrical energies between 1 and 19 kJ are discharged within a few microseconds across the electrodes of the coaxial gun, accelerating deuterium gas samples to plasma beam energies well beyond the keV energy range. The focus of this study is to examine the interaction of the plasma beam with a deuterated target by designing and fabricating a detector to measure neutron yield. Given the strong electromagnetic pulse associated with our accelerator, indirect measurement of neutrons via threshold-dependent nuclear activation serves as both a reliable and definitive indicator of high-energy particles for our application. Upon bombardment with neutrons, discs or stacks of metal foils placed near the deuterated target undergo nuclear activation reactions, yielding gamma-emitting isotopes whose decay is measured by a scintillation detector system. By collecting gamma ray spectra over time and considering nuclear cross sections, the magnitude of the original neutron pulse is inferred.

  7. Interpretation of Core Length in Shear Coaxial Rocket Injectors from X-ray Radiography Measurements

    Science.gov (United States)

    2014-06-01

    Shear Coaxial Rocket Injectors from X-ray Radiography Measurements 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT...ASME/SAE/ASEE Joint Propulsion Conference, Cleveland, OH, 28-30 July, 2014. PA#14340 14. ABSTRACT Shear coaxial injectors are so named because they...Length in Shear Coaxial Rocket Injectors from X-ray Radiography Measurements S. Alexander Schumaker1, Stephen A. Danczyk2 and Malissa D.A. Lightfoot2

  8. BEPC II wire scanner system

    Institute of Scientific and Technical Information of China (English)

    SUI Yan-Feng; WANG Lin; ZHAO Ying; YUE Jun-Hui; LI Xiao-Ping; CAO Jian-She; MA Li

    2010-01-01

    To monitor the beam profile at the end of the linac non-destructively,a wire scanner as a new diagnostic instrument was designed,manufactured and installed in 2007.Since then,several measurements have been carried out using this device.This paper describes the whole system of the wire scanner and the testing results.

  9. Wire and Packing Tape Sandwiches

    Science.gov (United States)

    Rabinowitz, Sandy

    2009-01-01

    In this article, the author describes how students can combine craft wire with clear packing tape to create a two-dimensional design that can be bent and twisted to create a three-dimensional form. Students sandwich wire designs between two layers of tape. (Contains 1 online resource.)

  10. Investigation of Constant Temperature Hot-wire System Response using Laser Pulse

    Science.gov (United States)

    Jaffa, Nicholas; Morris, Scott; Cameron, Joshua

    2016-11-01

    Constant temperature hot-wire systems use a Wheatstone bridge and feedback amplifier circuit to maintain a constant average temperature across the wire yielding frequency responses of order 100 kHz. This high frequency response allows hot-wires to be used extensively for aerodynamic measurements in high speed flows and uncertainty at these high frequencies can be difficult to diagnose. The standard frequency response check for constant temperature hot-wires uses an electronic pulse across the circuit to check the electronic feedback circuit response time, but does not account for the impact of the heat transfer along the wire. In order to investigate the frequency response of the entire constant temperature hot-wire system, including the heat transfer along the wire, a novel method was developed using a pulsed PIV laser focused to illuminate only the hot-wire. The laser pulse duration was effectively an instantaneous change in wire surface temperature through radiation. A hot-wire was placed in a uniform open calibration jet for a range of flow conditions. The response of the entire hot-wire system was observed across a range of conditions including changes in flow, wire temperature, and thermal boundary conditions and compared with the electronic pulse test.

  11. Electrochemical corrosion behavior of steel wires in a coalmine with a corrosive medium

    Institute of Scientific and Technical Information of China (English)

    Wang Songquan; Zhang Dekun; Wang Dagang; Zhang Zefeng

    2011-01-01

    A 6 × 19 point-contact hoisting cable was used as our research object to examine the progress of corrosion of steel wires in a laboratory, simulating the actual working conditions in a coalmine. An electrochemical method was used to investigate the corrosion behavior of steel wires with different surface treatments of a corrosive acid solution. The results show that anode activation of steel wire mainly occurs during pre-corrosion, where the anode activation process of bare steel wires is the fastest as is their corresponding corrosion speed, while the anode activation process of oil coated steel wires and their corresponding corrosion speed are the lowest. During the intermediate and late immersion periods,a passive film is generated on the surface of steel wires, which are gradually damaged with the passage of time. Local pitting corrosion occurs easily on the surface of steel wires with a high-polarization potential.Suitable equivalent circuits were chosen to fit the electrochemical impedance spectroscopy (EIS) of steel wires over various corrosive times and different surface treatments, which indicate good fitting results.The double electrical layer charge-transfer resistance increases in the sequence: bare steel wire,untreated steel wire and oil coated steel wire and their corrosion resistance decreases in turn, which is consistent with their polarization curves. The oil layer provides a certain protective effect on untreated steel wires, but its effect is not entirely clear.

  12. Prediction of grain deformation in drawn copper wire

    Directory of Open Access Journals (Sweden)

    Chang Chao-Cheng

    2015-01-01

    Full Text Available Most copper wire is produced using a drawing process. The crystallographic texture of copper wire, which is strongly associated with grain deformation, can have a profound effect on the formability and mechanical and electrical properties. Thus, the ability to predict grain deformation in drawn copper wire could help to elucidate the evolution of microstructure, which could be highly valuable in product design. This study developed a novel method for predicting grain deformation in drawn copper wire based on finite element simulation with flow net analysis. Simple upsetting tests were conducted to obtain flow stress curves for the simulation of the drawing process. Predictions related to grain deformation were compared with those on the micrographs of the drawn copper wire obtained in experiments. In longitudinal and transverse cross-sections of the drawn wire, the predicted and experiment results presented similar trends involving considerable deformation within the grains. This preliminary study demonstrates the efficacy of the proposed method in providing information useful to the prediction of the grain deformation in drawn copper wire.

  13. 3D coaxial out-of-plane metallic antennas for filtering and multi-spectral imaging in the infrared range.

    Science.gov (United States)

    Jacassi, Andrea; Bozzola, Angelo; Zilio, Pierfrancesco; Tantussi, Francesco; De Angelis, Francesco

    2016-06-27

    We fabricated and investigated a new configuration of 3D coaxial metallic antennas working in the infrared which combines the strong lateral light scattering of vertical plasmonic structures with the selective spectral transmission of 2D arrays of coaxial apertures. The coaxial structures are fabricated with a top-down method based on a template of hollow 3D antennas. Each antenna has a multilayer radial structure consisting of dielectric and metallic materials not achievable in a 2D configuration. A planar metallic layer is inserted normally to the antennas. The outer dielectric shell of the antenna defines a nanometric gap between the horizontal plane and the vertical walls. Thanks to this aperture, light can tunnel to the other side of the plane, and be transmitted to the far field in a set of resonances. These are investigated with finite-elements electromagnetic calculations and with Fourier-transform infrared spectroscopy measurements. The spectral position of the resonances can be tuned by changing the lattice period and/or the antenna length. Thanks to the strong scattering provided by the 3D geometry, the transmission peaks possess a high signal-to-noise ratio even when the illuminated area is less than 2 × 2 times the operation wavelength. This opens new possibilities for multispectral imaging in the IR with wavelength-scale spatial resolution.

  14. Numerical and experimental design of coaxial shallow geothermal energy systems

    Science.gov (United States)

    Raghavan, Niranjan

    Geothermal Energy has emerged as one of the front runners in the energy race because of its performance efficiency, abundance and production competitiveness. Today, geothermal energy is used in many regions of the world as a sustainable solution for decreasing dependence on fossil fuels and reducing health hazards. However, projects related to geothermal energy have not received their deserved recognition due to lack of computational tools associated with them and economic misconceptions related to their installation and functioning. This research focuses on numerical and experimental system design analysis of vertical shallow geothermal energy systems. The driving force is the temperature difference between a finite depth beneath the earth and its surface stimulates continuous exchange of thermal energy from sub-surface to the surface (a geothermal gradient is set up). This heat gradient is captured by the circulating refrigerant and thus, tapping the geothermal energy from shallow depths. Traditionally, U-bend systems, which consist of two one-inch pipes with a U-bend connector at the bottom, have been widely used in geothermal applications. Alternative systems include coaxial pipes (pipe-in-pipe) that are the main focus of this research. It has been studied that coaxial pipes have significantly higher thermal performance characteristics than U-bend pipes, with comparative production and installation costs. This makes them a viable design upgrade to the traditional piping systems. Analytical and numerical heat transfer analysis of the coaxial system is carried out with the help of ABAQUS software. It is tested by varying independent parameters such as materials, soil conditions and effect of thermal contact conductance on heat transfer characteristics. With the above information, this research aims at formulating a preliminary theoretical design setup for an experimental study to quantify and compare the heat transfer characteristics of U-bend and coaxial

  15. Wire metamaterials: physics and applications.

    Science.gov (United States)

    Simovski, Constantin R; Belov, Pavel A; Atrashchenko, Alexander V; Kivshar, Yuri S

    2012-08-16

    The physics and applications of a broad class of artificial electromagnetic materials composed of lattices of aligned metal rods embedded in a dielectric matrix are reviewed. Such structures are here termed wire metamaterials. They appear in various settings and can operate from microwaves to THz and optical frequencies. An important group of these metamaterials is a wire medium possessing extreme optical anisotropy. The study of wire metamaterials has a long history, however, most of their important and useful properties have been revealed and understood only recently, especially in the THz and optical frequency ranges where the wire media correspond to the lattices of microwires and nanowires, respectively. Another group of wire metamaterials are arrays and lattices of nanorods of noble metals whose unusual properties are driven by plasmonic resonances. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  16. FIRAS wire grid characterization techniques

    Science.gov (United States)

    Barney, Richard D.; Magner, Thomas J.

    1989-01-01

    Characterization techniques used to verify the quality and spectral performance of the large freestanding wire grid polarizing beamsplitters and input/output polarizers used in the Far Infrared Absolute Spectrophotometer (FIRAS) are presented. The clear aperture of these grids is lined with 20.8 micron diameter gold coated tungsten wire, spaced 33 microns apart. The grid characteristics measured throughout fabrication and space flight qualification are the center to center wire spacing and wire plane flatness. Ideally, the wire grids should produce coherent wavefronts with equal reflectance and transmittance properties. When the spacing is inconsistent, these wavefront intensities are unequal, thus decreasing the efficiency of the grids and reducing the output signal of the FIRAS. The magnitude of the output interferogram is also reduced by incoherence in the interfering wave fronts caused by uneven flatness.

  17. Forging Cr12MoV Steel Rolling Method of Influence on Quality of Wire Wheel Research%锻造方法对Cr12MoV钢滚丝轮质量的影响研究

    Institute of Scientific and Technical Information of China (English)

    王金发; 宋学全; 张珂禹; 姜连德

    2011-01-01

    The influences to the unevenness, forging inside crack, mechanical properties, heat treatment deformation and service life of the carbide of Cr12MoV steel rolling wire which occurred by different forging methods was studied by comparing the different forging technology of upsetting and drawing, forming, margining and so on.%通过镦拔、成形、滚边等不同锻造工艺的对比,研究了锻造方法对Cr12MoV钢滚丝轮碳化物不均匀度、锻件内裂、机械性能、热处理变形量、使用寿命等的影响.

  18. Study on the pre——ignition characteristics of wire insulation in the narrow channel setup

    Institute of Scientific and Technical Information of China (English)

    WANG Kai; WANG BaoRui; AI YuHua; KONG WenJun

    2012-01-01

    A narrow channel setup was established and experiments were conducted to study the pre-ignition characteristics of wire insulation under overload conditions in weak buoyancy environment.The pre-ignition temperature variation trend of both the wire insulation and its nearby temperature monitoring points,the movement characteristics of smoke produced from the wire insulation and the ignition delay time of wire insulation were investigated.The results indicated that the narrow channel setup with a height of 10-15 mm was effective to suppress the effect of buoyancy,and the pre-ignition characteristics of wire insulation in microgravity could be predicted well by the narrow channel method.

  19. [Separate vertical wiring combined with tension band and Kirschner-wire plus cerclage wire in the treatment of displaced inferior pole fractures of the patella].

    Science.gov (United States)

    Zhang, J; Jiang, X Y; Huang, X W

    2016-06-18

    To investigate the clinical efficacy and outcomes of two separate vertical wiring combined with tension band and Kirschner-wire plus cerclage wire in the treatment of displaced inferior pole fractures of the patella. From January 2013 to January 2015, 15 consecutive patients (mean age 54.5 years) with inferior pole fractures of the patella were retrospectively included in this study. All the patients underwent open reduction and internal fixation by separate vertical wiring combined with tension band and Kirschner-wire plus cerclage wire through longitudinal incision, 4.5 d (range: 3.1-5.9 d) after initial injury. A safety check for early knee range of motion was performed before wound closure. The complications including infection, nonunion, loss of fixation and any wire breakage or irritation from implant were recorded. Anteroposterior and lateral views of the knee joint obtained during the follow-up were used to assess bony union based on the time when the fracture line disappeared. At the time of the final outpatient follow up, functional evaluation of the knee joint was conducted by Bostman system. The follow-up time was 13.1 months (range: 12-19 months) after surgery on average, immediate motion without immobilization in all the cases was allowed and there was no case of reduction loss of the fracture and wire breakage. There was no case of irritation from the implant. At the final follow-up, the average range of motion (ROM) arc was 126.7° (range: 115°-140°), the average ROM lag versus contralateral healthy leg was 10.3° (range: 0°-35°). The mean Bostman score at the last follow-up was 28.9 (range: 27-30), and graded excellent in most cases. Two separate vertical wiring is an easy and effective method to reduce the displaced inferior pole fracture of patella. Augmentation of separate vertical wiring with tension band and Kirschner-wire plus cerclage wire in these patients provides enough strength to protected the early exercise of the knee joint and

  20. Broadband microwave measurement of electron temperature of a large coaxial gridded hollow cathode helium plasma

    Science.gov (United States)

    Gao, Ruilin; Yuan, Chengxun; Jia, Jieshu; Zhou, Zhong-Xiang; Wang, Ying; Wang, Xiaoou; Li, Hui; Wu, Jian

    2016-10-01

    This paper reports a new kind of large coaxial gridded hollow cathode discharge at low pressure in a helium atmosphere. A method is presented to determine the electron temperature by measuring the broadband microwave properties; typically, the frequency band extends from 2 to 12 GHz. The method involves positioning the discharge device between the two antenna ports to measure the scattering parameter using a network analyzer. For a weak ionized plasma, this method is stable over the entire frequency range. A microwave signal loss of 0.27-37.83 dB was measured within the frequency range. Based on the measured attenuation of the microwaves, the electron temperature was estimated to range from 1.6-4.6 eV under different conditions, which showed good agreements with the results of Langmuir Probe measurements.

  1. Preparation of Coaxial-Line and Hollow Mn2O3 Nanofibers by Single-Nozzle Electrospinning and Their Catalytic Performances for Thermal Decomposition of Ammonium Perchlorate.

    Science.gov (United States)

    Liang, Jiyuan; Yang, Jie; Cao, Weiguo; Guo, Xiangke; Guo, Xuefeng; Ding, Weiping

    2015-09-01

    Coaxial-line and hollow Mn2O3 nanofibers have been synthesized by a simple single-nozzle electrospinning method without using a complicated coaxial jet head, combined with final calcination. The crystal structure and morphology of the Mn2O3 nanofibers were investigated by using the X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The results indicate that the electrospinning distance has important influence on the morphology and structure of the obtained Mn2O3 nanofibers, which changes from hollow fibers for short electrospinning distance to coaxial-line structure for long electrospinning distance after calcination in the air. The formation mechanisms of different structured Mn2O3 fibers are discussed in detail. This facile and effective method is easy to scale up and may be versatile for constructing coaxial-line and hollow fibers of other metal oxides. The catalytic activity of the obtained Mn2O3 nanofibers on thermal decomposition of ammonium perchlorate (AP) was studied by differential scanning calorimetry (DSC). The results show that the hollow Mn2O3 nanofibers have good catalytic activity to promote the thermal decomposition of AP.

  2. New hot wire anemometer with alternate current and synchronic detection

    Science.gov (United States)

    Stoian, Monica; Rachek, Adil; Chirtoc, Mihai

    2009-01-01

    The feasibility of hot wire anemometer in to a new measurement configuration is demonstrated in this work and we validate our results by a numerical model. We have created an anemometer probe with hot wire using a new scheme, in alternate current and synchronic detection (3ω method). We use this instrument to register the velocity magnitude in boundary layer for a forced convection flow. The probe and its alimentation also the measuring support and bridge Wheatstone, have been created by us. The physical parameter was recorded is an exchange heat quantity between hot wire and fluid flow. In steady state, experimental data verify the numerical results with an average error of 3%.

  3. Comparison of surgically induced astigmatism after coaxial phacoemulsification through 1.8 mm microincision and bimanual phacoemulsification through 1.7 mm microincision.

    Science.gov (United States)

    Wilczynski, Michal; Supady, Ewa; Piotr, Loba; Synder, Aleksandra; Palenga-Pydyn, Dorota; Omulecki, Wojciech

    2009-09-01

    To compare surgically induced astigmatism (SIA) after coaxial 1.8 mm microincision cataract surgery (MICS) and bimanual 1.7 mm MICS calculated with 3 mathematical methods. Department of Ophthalmology, Medical University of Lodz, Lodz, Poland. Study comprised a nonrandomized prospective consecutive series of 58 eyes of 58 patients who had uneventful coaxial MICS with implantation of an Akreos MI60 foldable intraocular lens (IOL) using a 1.8 mm temporal clear corneal incision. Fifty eyes of 50 patients who had uneventful bimanual MICS through a 1.7 mm clear corneal incision for a sleeveless phaco tip and a 1.5 mm side port for an irrigating chopper with implantation of an Acri.Smart 48S foldable IOL served as a comparison group. All surgery was performed by 2 experienced surgeons. Surgically induced astigmatism was calculated using 3 methods. The patients were examined preoperatively and 2 weeks to 1 month postoperatively. No intraoperative or postoperative complications were seen in any patient. The corrected distance visual acuity improved significantly in both groups after surgery (P.05). In vector analysis, the mean SIA was 0.42 +/- 0.29 in the coaxial MICS group and 0.50 +/- 0.24 in the bimanual group; the difference was not statistically significant (P>.05). In vector decomposition, the mean SIA (C90) coaxial MICS group was 0.23 +/- 0.29 in the coaxial MICS group and 0.23 +/- 0.22 in the bimanual MICS group; the difference was not significant. Using the Naeser method, DeltaKP-90 was calculated, amounting to 0.05 +/- 0.44 in the coaxial MICS group and -0.04 +/- 0.42 in the bimanual MICS group; the difference was not significant. The amount of SIA induced by bimanual MICS and coaxial MICS phacoemulsification was very small. The bimanual MICS induced a slightly higher degree of SIA; however, according to all methods of SIA analysis, there was no significant difference in the mean SIA induced by both techniques.

  4. Nano-storage wires.

    Science.gov (United States)

    Lee, Dong Jun; Kim, Eunji; Kim, Daesan; Park, Juhun; Hong, Seunghun

    2013-08-27

    We report the development of "nano-storage wires" (NSWs), which can store chemical species and release them at a desired moment via external electrical stimuli. Here, using the electrodeposition process through an anodized aluminum oxide template, we fabricated multisegmented nanowires composed of a polypyrrole segment containing adenosine triphosphate (ATP) molecules, a ferromagnetic nickel segment, and a conductive gold segment. Upon the application of a negative bias voltage, the NSWs released ATP molecules for the control of motor protein activities. Furthermore, NSWs can be printed onto various substrates including flexible or three-dimensional structured substrates by direct writing or magnetic manipulation strategies to build versatile chemical storage devices. Since our strategy provides a means to store and release chemical species in a controlled manner, it should open up various applications such as drug delivery systems and biochips for the controlled release of chemicals.

  5. Study of microwave magnetoimpedance effect in amorphous FeSiB wires

    Science.gov (United States)

    Britel, M. R.; Garcia, C.; Ciureanu, P.; Gauthier, J.; Akyel, C.; Gonzalez, J.; Yelon, A.

    2007-09-01

    Measurements of microwave magnetoimpedance of melt-extracted Fe-rich amorphous wires are presented. These wires were simultaneously submitted to a microwave electromagnetic wave propagating at the wire surface, Joule heating and circumferential static magnetic field. This field is generated by a DC electric current flowing through the wire with maximum strength of 90 mA in order not to reach the recrystallization temperature of the amorphous alloy. The impedance was measured up to 6 GHz using a technique based on the s-parameters measurement of a custom-designed coaxial line by means of a vectorial network analyzer. The real part of the impedance spectra we obtained show peaks, which characterize the magnetic losses occurring in the amorphous material. These peaks shift toward lower frequency for stronger DC currents. Theoretically, these results can be accounted for by the fact that the peaks frequency represents the ferromagnetic resonance occurring in the magnetic material. Its magnitude depends on the saturation magnetization. Since this magnetization decreases with temperature following the Curie law, the resonance frequency also decreases and the impedance peaks shift towards lower frequency.

  6. Photonic band gap in thin wire metamaterials.

    Science.gov (United States)

    Hock, Kai Meng

    2008-03-01

    We investigate the band structure of a class of photonic crystals made from only thin wires. Using a different method, we demonstrate that a complete photonic band gap is possible for such materials. Band gap materials normally consist of space filling dielectric or metal, whereas thin wires occupy a very small fraction of the volume. We show that this is related to the large increase in scattering at the Brillouin zone boundary. The method we developed brings together the calculation techniques in three different fields. The first is the calculation of scattering from periodic, tilted antennas, which we improve upon. The second is the standard technique for frequency selective surface design. The third is obtained directly from low energy electron diffraction theory. Good agreements with experiments for left handed materials, negative materials, and frequency selective surfaces are demonstrated.

  7. OCC技术制备的单晶铜线材冷拔组织TEM分析%TEM Analysis of Drawn Single Crystal Copper Wires Produced by OCC Method

    Institute of Scientific and Technical Information of China (English)

    陈建; 严文; 苗健; 彭渝莉; 范新会

    2011-01-01

    采用TEM系统分析了OCC技术制备的单晶铜线材在冷拔过程中形成的位错胞、几何必须界面以及孪晶,发现当真应变小于0.94时,冷拔单晶铜线材的微观组织为位错胞.当真应变大于0.94时,其微观组织主要包括位错胞和几何必须界面两类组织.其中位错胞沿冷拔方向拉长,横界面上为等轴状.随变形量的增加,位错胞尺寸减小,当真应变大于1.39时,位错胞尺寸不再随塑性变形量的增加而减小,其直径保持在0.28 μm左右.当变形量比较小时,两类几何必须位错界面属于晶体学界面,当变形量比较大时,几何必须位错界面与冷拔方向平行.同时,分析还发现冷拔单晶铜线材中存在少量由凝固过程形成并遗传到形变组织以及在冷拔过程直接形成的两类孪晶.%Dislocation cells, geometrically necessary boundaries (GNB) and twins in drawn single crystal copper wires produced by Ohno continuous casting (OCC) method have been analyzed by TEM. The results show that when the strains are lower than 0.94, the microstructures of drawn single crystal can be characterized as dislocation cells. When the strains are more than 0.94, there are two kinds of microstructures. One is that dislocation cells are elongated in longitudinal section and equiaxed in cross section. The size of dislocation cells decreases as the strain increases until they reach a critical size of about 0.28 urn at a strain of 1.39. The other is geometrically necessary boundaries. At low strains, two kinds of geometrically necessary boundaries are along {111}, and at high strains, geometrically necessary boundaries are parallel to drawn direction. In addition, it is found that in dawn single crystal copper wires, there are two types of twins in the single crystal copper wires. One is formed in the preparing process of single crystal copper wires by Ohno continuous casting method, and the other is formed during cold drawing deformation.

  8. Computer simulation of metal wire explosion under high rate heating

    Science.gov (United States)

    Zolnikov, K. P.; Kryzhevich, D. S.; Korchuganov, A. V.

    2017-05-01

    Synchronous electric explosion of metal wires and synthesis of bicomponent nanoparticles were investigated on the base of molecular dynamics method. Copper and nickel nanosized crystallites of cylindrical shape were chosen as conductors for explosion. The embedded atom approximation was used for calculation of the interatomic interactions. The agglomeration process after explosion metal wires was the main mechanism for particle synthesis. The distribution of chemical elements was non-uniform over the cross section of the bicomponent particles. The copper concentration in the surface region was higher than in the bulk of the synthesized particle. By varying the loading parameters (heating temperature, the distance between the wires) one can control the size and internal structure of the synthesized bicomponent nanoparticles. The obtained results showed that the method of molecular dynamics can be effectively used to determine the optimal technological mode of nanoparticle synthesis on the base of electric explosion of metal wires.

  9. Plasma chemistry in wire chambers

    Energy Technology Data Exchange (ETDEWEB)

    Wise, J.

    1990-05-01

    The phenomenology of wire chamber aging is discussed and fundamentals of proportional counters are presented. Free-radical polymerization and plasma polymerization are discussed. The chemistry of wire aging is reviewed. Similarities between wire chamber plasma (>1 atm dc-discharge) and low-pressure rf-discharge plasmas, which have been more widely studied, are suggested. Construction and use of a system to allow study of the plasma reactions occurring in wire chambers is reported. A proportional tube irradiated by an {sup 55}Fe source is used as a model wire chamber. Condensable species in the proportional tube effluent are concentrated in a cryotrap and analyzed by gas chromatography/mass spectrometry. Several different wire chamber gases (methane, argon/methane, ethane, argon/ethane, propane, argon/isobutane) are tested and their reaction products qualitatively identified. For all gases tested except those containing methane, use of hygroscopic filters to remove trace water and oxygen contaminants from the gas resulted in an increase in the average molecular weight of the products, consistent with results from low-pressure rf-discharge plasmas. It is suggested that because water and oxygen inhibit polymer growth in the gas phase that they may also reduce polymer deposition in proportional tubes and therefore retard wire aging processes. Mechanistic implications of the plasma reactions of hydrocarbons with oxygen are suggested. Unresolved issues in this work and proposals for further study are discussed.

  10. Buoyant Helical Twin-Axial Wire Antenna

    Science.gov (United States)

    2016-11-15

    Wire Antenna” by the inventor, David A. Tonn. STATEMENT OF GOVERNMENT INTEREST [0002] The invention described herein may be manufactured and used by...BACKGROUND OF THE INVENTION (1) Field of the Invention [0003] The present invention is directed to a linear antenna for dual frequencies and a method for...curves and hinders the submarine’s operations when using the antenna. SUMMARY OF THE INVENTION [0006] It is a first object of the present

  11. Multi-Frequency Analysis For Interstitial Microwave Hyperthermia Using Multi-Slot Coaxial Antenna

    Science.gov (United States)

    Gas, Piotr

    2015-01-01

    The presented paper shows a new concept of multi-slot coaxial antenna working at different frequencies to predict the best solution for interstitial microwave hyperthermia treatment. The described method concerns a microwave heating of unhealthy cells using a thin microwave antenna located in the human tissue. Therefore, the coupled wave equation in a sinusoidal steady-state and the transient bioheat equation under an axial symmetrical model are considered. The 4-Cole-Cole approximation has been used to compute the complex relative permittivity of the human tissues at different antenna operating frequencies. At the stage of numerical simulation the finite element method (FEM) is used. Special attention has been paid to estimate the optimal antenna parameters for thermal therapy for three microwave frequencies mainly used in medical practice and make comparison of the obtained results in the case of single-, double- and triple-slot antennas.

  12. Fluoride influences nickel-titanium orthodontic wires' surface texture and friction resistance

    Science.gov (United States)

    Abbassy, Mona Aly

    2016-01-01

    Objectives: The aim of this study was to investigate the effects exerted by the acidulated fluoride gel on stainless steel and nickel-titanium (Ni-Ti) orthodontic wires. Materials and Methods: Sixty stainless steel and Ni-Ti orthodontic archwires were distributed into forty archwires used for in vitro study and twenty for in situ study. Fluoride was applied for 1 h in the in vitro experiment while it was applied for 5 min in the in situ experiment. The friction resistance of all wires with ceramic brackets before/after topical fluoride application was measured using a universal testing machine at 1 min intervals of moving wire. Moreover, surface properties of the tested wires before/after fluoride application and before/after friction test were examined by a scanning electron microscope (SEM). Dunnett's t-test was used to compare frictional resistance of as-received stainless steel wires and Ni-Ti wires to the wires treated by fluoride in vitro and in situ (P < 0.05). Two-way ANOVA was used to compare the effect of fluoride application and type of wire on friction resistance in vitro and in situ (P < 0.05). Results: Ni-Ti wires recorded significantly high friction resistance after fluoride application when compared to stainless steel wires in vitro, P < 0.05. Fluoride application did not significantly affect the friction resistance of the tested wires in situ, P < 0.05. SEM observation revealed deterioration of the surface texture of the Ni-Ti wires after fluoride application in vitro and in situ. Conclusions: The in vitro fluoride application caused an increase in friction resistance of Ni-Ti wires when compared to stainless steel wires. In vitro and in situ fluoride application caused deterioration in surface properties of Ni-Ti wires. PMID:27843886

  13. Plasto-hydrodynamic polymer coating of fine wires

    OpenAIRE

    Lamb, Roger E.

    1989-01-01

    This project outlines the design and commissioning of a multi-purpose drawing bench and pressure die chamber so as to coat fine wires. The pressure chamber was designed along similar lines to the pressure chambers used by previous researchers for Plasto-hydrodynamic die-less drawing of wire. The commissioning and future safe operation of the drawing bench have been described. The experimental proceedures and methods have been outlined. Investigations into a wide ra...

  14. Coaxial silicon nanowires as solar cells and nanoelectronic power sources.

    Science.gov (United States)

    Tian, Bozhi; Zheng, Xiaolin; Kempa, Thomas J; Fang, Ying; Yu, Nanfang; Yu, Guihua; Huang, Jinlin; Lieber, Charles M

    2007-10-18

    Solar cells are attractive candidates for clean and renewable power; with miniaturization, they might also serve as integrated power sources for nanoelectronic systems. The use of nanostructures or nanostructured materials represents a general approach to reduce both cost and size and to improve efficiency in photovoltaics. Nanoparticles, nanorods and nanowires have been used to improve charge collection efficiency in polymer-blend and dye-sensitized solar cells, to demonstrate carrier multiplication, and to enable low-temperature processing of photovoltaic devices. Moreover, recent theoretical studies have indicated that coaxial nanowire structures could improve carrier collection and overall efficiency with respect to single-crystal bulk semiconductors of the same materials. However, solar cells based on hybrid nanoarchitectures suffer from relatively low efficiencies and poor stabilities. In addition, previous studies have not yet addressed their use as photovoltaic power elements in nanoelectronics. Here we report the realization of p-type/intrinsic/n-type (p-i-n) coaxial silicon nanowire solar cells. Under one solar equivalent (1-sun) illumination, the p-i-n silicon nanowire elements yield a maximum power output of up to 200 pW per nanowire device and an apparent energy conversion efficiency of up to 3.4 per cent, with stable and improved efficiencies achievable at high-flux illuminations. Furthermore, we show that individual and interconnected silicon nanowire photovoltaic elements can serve as robust power sources to drive functional nanoelectronic sensors and logic gates. These coaxial silicon nanowire photovoltaic elements provide a new nanoscale test bed for studies of photoinduced energy/charge transport and artificial photosynthesis, and might find general usage as elements for powering ultralow-power electronics and diverse nanosystems.

  15. Cavity Mode Related Wire Breaking of the SPS Wire Scanners and Loss Measurements of Wire Materials

    CERN Document Server

    Caspers, Friedhelm; Jensen, E; Koopman, J; Malo, J F; Roncarolo, F

    2003-01-01

    During the SPS high intensity run 2002 with LHC type beam, the breaking of several of the carbon wires in the wire scanners has been observed in their parking position. The observation of large changes in the wire resistivity and thermionic electron emission clearly indicated strong RF heating that was depending on the bunch length. A subsequent analysis in the laboratory, simulating the beam by two probe antennas or by a powered stretched wire, showed two main problems: i) the housing of the wire scanner acts as a cavity with a mode spectrum starting around 350 MHz and high impedance values around 700 MHz; ii) the carbon wire used so far appears to be an excellent RF absorber and thus dissipates a significant part of the beam-induced power. Different wire materials are compared with the classical cavity mode technique for the determination of the complex permittivity in the range of 2-4 GHz. As a resonator a rectangular TE_01n type device is utilized.

  16. Cavity mode related wire breaking of the SPS Wire Scanners and loss measurements of wire materials

    CERN Document Server

    Roncarolo, Federico

    2003-01-01

    During the SPS high intensity run 2002 with LHC type beam, the breaking of several of the carbon wires in the wire scanners has been observed in their parking position. The observation of large changes in the wire resistivity and thermionic electron emission clearly indicated strong RF heating that was depending on the bunch length. A subsequent analysis in the laboratory, simulating the beam by two probe antennas or by a powered stretched wire, showed two main problems: i) the housing of the wire scanner acts as a cavity with a mode spectrum starting around 350MHz and high impedance values around 700 MHz; ii) the carbon wire used so far appears to be an excellent RF absorber and thus dissipates a significant part of the beam-induced power. Different wire materials are compared with the classical cavity mode technique for the determination of the complex permittivity in the range of 2-4 GHz. As a resonator a rectangular TE01n type device is utilized.

  17. Plasma-filled diode based on the coaxial gun.

    Science.gov (United States)

    Zherlitsyn, A A; Kovalchuk, B M; Pedin, N N

    2012-10-01

    The paper presents the results of studies of a coaxial gun for a plasma-filled electron diode. Effects of the discharge channel diameter and gun current on characteristics of the plasma and pulse generated in the diode were investigated. The electron beam with maximum energy of ≥1 MeV at the current of ≈100 kA was obtained in the experiments with a plasma-filled diode. The energy of ≈5 kJ with the peak power of ≥100 GW dissipated in the diode.

  18. Review of coaxial flow gas core nuclear rocket fluid mechanics

    Science.gov (United States)

    Weinstein, H.

    1976-01-01

    Almost all of the fluid mechanics research associated with the coaxial flow gas core reactor ended abruptly with the interruption of NASA's space nuclear program because of policy and budgetary considerations in 1973. An overview of program accomplishments is presented through a review of the experiments conducted and the analyses performed. Areas are indicated where additional research is required for a fuller understanding of cavity flow and of the factors which influence cold and hot flow containment. A bibliography is included with graphic material.

  19. Theory and Circuit Model for Lossy Coaxial Transmission Line

    Energy Technology Data Exchange (ETDEWEB)

    Genoni, T. C.; Anderson, C. N.; Clark, R. E.; Gansz-Torres, J.; Rose, D. V.; Welch, Dale Robert

    2017-04-01

    The theory of signal propagation in lossy coaxial transmission lines is revisited and new approximate analytic formulas for the line impedance and attenuation are derived. The accuracy of these formulas from DC to 100 GHz is demonstrated by comparison to numerical solutions of the exact field equations. Based on this analysis, a new circuit model is described which accurately reproduces the line response over the entire frequency range. Circuit model calculations are in excellent agreement with the numerical and analytic results, and with finite-difference-time-domain simulations which resolve the skindepths of the conducting walls.

  20. Space charge effects for multipactor in coaxial lines

    Energy Technology Data Exchange (ETDEWEB)

    Sorolla, E., E-mail: eden.sorolla@xlim.fr [XLIM, UMR 7252, Université de Limoges/CNRS, 123 Av. Albert Thomas, 87060 Limoges (France); Sounas, A.; Mattes, M. [Laboratoire d' Électromagnétisme et d' Acoustique (LEMA), École Polytechnique Fédérale de Lausanne, Station 11, CH-1015 Lausanne (Switzerland)

    2015-03-15

    Multipactor is a hazardous vacuum discharge produced by secondary electron emission within microwave devices of particle accelerators and telecommunication satellites. This work analyzes the dynamics of the multipactor discharge within a coaxial line for the mono-energetic electron emission model taking into account the space charge effects. The steady-state is predicted by the proposed model and an analytical expression for the maximum number of electrons released by the discharge presented. This could help to link simulations to experiments and define a multipactor onset criterion.

  1. Simulation of non-linear coaxial line using ferrite beads

    Energy Technology Data Exchange (ETDEWEB)

    Furuya, S.; Matsumoto, H.; Tachi, K.; Takano, S.; Irisawa, J. [Nagaoka Univ. of Technology, Niigata (Japan)

    2002-06-01

    A ferrite sharpener is a non-linear coaxial line using ferrite beads, which produces high-voltage, high-dV/dt pulses. We have been examining the characteristics of ferrite sharpeners experimentally, varying various parameters. Also we have made the simulation of the ferrite sharpener and compared the predictions with the experimental results in detail to analyze the characteristics of the sharpener. In this report, calculating the magnetization M of the ferrite bead, we divide the bead into n sections radially instead of adopting M at the average radius in the previous report. (author)

  2. Plasma-filled diode based on the coaxial gun

    Energy Technology Data Exchange (ETDEWEB)

    Zherlitsyn, A. A.; Kovalchuk, B. M.; Pedin, N. N. [Institute of High Current Electronics, 2/3 Academichesky Avenue, 634055 Tomsk (Russian Federation)

    2012-10-15

    The paper presents the results of studies of a coaxial gun for a plasma-filled electron diode. Effects of the discharge channel diameter and gun current on characteristics of the plasma and pulse generated in the diode were investigated. The electron beam with maximum energy of {>=}1 MeV at the current of Almost-Equal-To 100 kA was obtained in the experiments with a plasma-filled diode. The energy of Almost-Equal-To 5 kJ with the peak power of {>=}100 GW dissipated in the diode.

  3. Plasma-filled diode based on the coaxial gun

    Science.gov (United States)

    Zherlitsyn, A. A.; Kovalchuk, B. M.; Pedin, N. N.

    2012-10-01

    The paper presents the results of studies of a coaxial gun for a plasma-filled electron diode. Effects of the discharge channel diameter and gun current on characteristics of the plasma and pulse generated in the diode were investigated. The electron beam with maximum energy of ≥1 MeV at the current of ≈100 kA was obtained in the experiments with a plasma-filled diode. The energy of ≈5 kJ with the peak power of ≥100 GW dissipated in the diode.

  4. A simple method for medial canthal reconstruction

    NARCIS (Netherlands)

    Wittkampf, ARM; Mourits, MP

    2001-01-01

    A simple method for medical canthal wiring reconstruction with the help of a homolaterally fixed osteosynthesis plate and a metal wire is presented. This avoids transnasal wiring and gives superior control when correcting the position of the lacerated Omedial canthus.

  5. "Cut wires grating – single longitudinal wire" planar metastructure to achieve microwave magnetic resonance in a single wire

    OpenAIRE

    G. Kraftmakher; V. Butylkin

    2012-01-01

    Here we present metastructures containing cut-wire grating and a single longitudinal cut-wire orthogonal to grating’s wires. Experimental investigations at microwaves show these structures can provide strong magnetic resonant response of a single nonmagnetic cut-wire in dependence on configuration and sizes in the case when metastructures are oriented along the direction of wave propagation and cut-wires of grating are parallel to the electric field of a plane electromagnetic wave. It is sugg...

  6. Full-wave CAD of a rectangular waveguide filter with integrated coaxial excitation

    NARCIS (Netherlands)

    Gerini, G.; Guglielmi, M.

    2001-01-01

    Coaxial waveguides are very commonly used in many microwave subsystems for the connection of various components. Significant size reduction could, therefore, be achieved by integrating the design of the coaxial transition in the computer-aided design (CAD) of microwave filters. In this context, we f

  7. Electrospun Flexible Coaxial Nanoribbons Endowed With Tuned and Simultaneous Fluorescent Color-Electricity-Magnetism Trifunctionality.

    Science.gov (United States)

    Shao, Hong; Ma, Qianli; Dong, Xiangting; Yu, Wensheng; Yang, Ming; Yang, Ying; Wang, Jinxian; Liu, Guixia

    2015-09-16

    In order to develop new-typed multifunctional nanocomposites, fluorescent-electrical-magnetic trifunctional coaxial nanoribbons with tunable fluorescent color, including white-light emission, have been successfully fabricated via coaxial electrospinning technology. Each stripe of coaxial nanoribbon is composed of a Fe3O4/PMMA core and a [Eu(BA)3phen+Dy(BA)3phen]/PANI/PMMA (PMMA = polymethyl methacrylate, BA = benzoic acid, phen = phenanthroline, polyaniline = PANI) shell. X-ray diffractometry (XRD), field emission scanning electron microscopy (FE-SEM), biological microscopy (BM), vibrating sample magnetometry (VSM), energy dispersive spectrometry (EDS), Hall effect measurement system and photoluminescence (PL) spectroscopy were employed to characterize the coaxial nanoribbons. Emitting color of the coaxial nanoribbons can be tuned by adjusting the contents of Dy(BA)3phen, Eu(BA)3phen, PANI and Fe3O4 in a wide color range of blue-white-orange under the excitation of 273-nm single-wavelength ultraviolet light. The coaxial nanoribbons simultaneously possess excellent luminescent performance, electrical conduction and magnetism compared with the counterpart composite nanoribbons. Furthermore, the electrical and magnetic performances of the coaxial nanoribbons also can be tunable by adding different quantities of PANI and Fe3O4 nanoparticles, respectively. The obtained coaxial nanoribbons have promising applications in many areas, such as electromagnetic interference shielding, microwave absorption, molecular electronics, biomedicine, future nanomechanics and display fields.

  8. Study on the Superluminal Group Velocity in a Coaxial Photonic Crystal

    Institute of Scientific and Technical Information of China (English)

    LuGuizhen; HuangZhixun; GuanJian

    2004-01-01

    In this paper, the superluminal group velocity in a coaxial photonic crystal is studied. The simulation of the effective refraction index in coaxial photonic crystal is performed. The group velocity is calculated based on the transmission line equations and compared with experimental results.

  9. Facile synthesis and magnetic study of Ni@polyamide 66 coaxial nanotube arrays

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiaoru, E-mail: lixiaoruqdu@126.com; Yang, Chao; Han, Ping; Zhao, Qingpei; Song, Guojun, E-mail: songguojunqdu@126.com

    2016-12-01

    Ni@polyamide 66 (PA66) core/shell coaxial double-layer nanotube arrays have been prepared in the nanopores of anodic aluminum oxide templates (AAO). The shell of PA66 nanotubes were formed first and then served as templates to deposit Ni nanotubes used as the core. The morphology, structures of the obtained arrays were examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The formation of this unique coaxial nanotube structure was confirmed by SEM and TEM images and X-ray diffraction (XRD). We further explored the magnetic properties of the obtained coaxial nanotube arrays with vibrating sample magnetometer (VSM) and found that Ni@PA66 coaxial nanotubes exhibited higher remanence ratio than that of Ni nanotubes. These Ni@PA66 coaxial nanotubes are promising to be used as templates to fill in other materials. - Highlights: • Ni@PA66 coaxial nanotubes are prepared successfully with PA66 nanotubes obtained first and then Ni nanotubes were deposited in PA66 nanotubes. • The magnetic property of Ni@PA66 coaxial nanotubes is better than that of Ni nanotubes. • Ni@PA66 coaxial nanotubes can be used as templates to fill in other materials.

  10. Coaxial nozzle-assisted 3D bioprinting with built-in microchannels for nutrients delivery.

    Science.gov (United States)

    Gao, Qing; He, Yong; Fu, Jian-zhong; Liu, An; Ma, Liang

    2015-08-01

    This study offers a novel 3D bioprinting method based on hollow calcium alginate filaments by using a coaxial nozzle, in which high strength cell-laden hydrogel 3D structures with built-in microchannels can be fabricated by controlling the crosslinking time to realize fusion of adjacent hollow filaments. A 3D bioprinting system with a Z-shape platform was used to realize layer-by-layer fabrication of cell-laden hydrogel structures. Curving, straight, stretched or fractured filaments can be formed by changes to the filament extrusion speed or the platform movement speed. To print a 3D structure, we first adjusted the concentration and flow rate of the sodium alginate and calcium chloride solution in the crosslinking process to get partially crosslinked filaments. Next, a motorized XY stages with the coaxial nozzle attached was used to control adjacent hollow filament deposition in the precise location for fusion. Then the Z stage attached with a Z-shape platform moved down sequentially to print layers of structure. And the printing process always kept the top two layers fusing and the below layers solidifying. Finally, the Z stage moved down to keep the printed structure immersed in the CaCl2 solution for complete crosslinking. The mechanical properties of the resulting fused structures were investigated. High-strength structures can be formed using higher concentrations of sodium alginate solution with smaller distance between adjacent hollow filaments. In addition, cell viability of this method was investigated, and the findings show that the viability of L929 mouse fibroblasts in the hollow constructs was higher than that in alginate structures without built-in microchannels. Compared with other bioprinting methods, this study is an important technique to allow easy fabrication of lager-scale organs with built-in microchannels.

  11. Superconducting wires and fractional flux

    Science.gov (United States)

    Sá de Melo, C. A. R.

    1996-05-01

    The quantization of flux quanta in superconductors is revisited and analyzed in a new geometry. The system analyzed is a superconducting wire. The geometry is such that the superconducting wire winds N times around an insulating cylinder and that the wire has its end connected back to its beginning, thus producing an N-loop short circuited solenoid. The winding number N acts as a topological index that controls flux quantization. In this case, fractional flux quanta can be measured through the center of the insulating cylinder, provided that the cylinder radius is small enough. The Little-Parks experiment for an identical geometry is discussed. The period of oscillation of the transition temperature of the wire is found to vary as 1/N in units of flux Φ relative to the flux quantum Φ0. When a SQUID is made in such a geometry the maximal current through the SQUID varies with period Φ0/N.

  12. Wire Jewelry/Black History.

    Science.gov (United States)

    Daniel, Robert A.; Robinson, Charles C.

    1984-01-01

    Described is a project which made the study of Black history more real to fifth graders by having them make wire jewelry, smaller versions of the ornate filigreed ironwork produced by slave blacksmiths. (RM)

  13. Dieless wire drawing with lasers

    Science.gov (United States)

    Liedl, G.; Schuöcker, D.

    2007-06-01

    Thin wires are produced by drawing through nozzle-like tools, so called dies, that suffer from strong wear due to friction. In order to avoid the latter disadvantage the dies can be replaced by a laser beam heating the wire to such extend that the yield strength becomes smaller than the tensile strength and thus the wire is elongated and consequently constricted. To avoid rupture, the wire is cooled down again after the desired reduction of the diameter is reached. A further important advantage of this new process is that only one drawing step with a laser can substitute a large number of mechanical drawing actions, thus making the process much more efficient. Theoretical considerations and experimental investigations prove the feasibility of the latter new laser process and are subject to a description in the actual paper.

  14. 49 CFR 236.74 - Protection of insulated wire; splice in underground wire.

    Science.gov (United States)

    2010-10-01

    ... underground wire. 236.74 Section 236.74 Transportation Other Regulations Relating to Transportation (Continued... wire; splice in underground wire. Insulated wire shall be protected from mechanical injury. The insulation shall not be punctured for test purposes. Splice in underground wire shall have insulation...

  15. 49 CFR 234.241 - Protection of insulated wire; splice in underground wire.

    Science.gov (United States)

    2010-10-01

    ... underground wire. 234.241 Section 234.241 Transportation Other Regulations Relating to Transportation... of insulated wire; splice in underground wire. Insulated wire shall be protected from mechanical injury. The insulation shall not be punctured for test purposes. A splice in underground wire shall have...

  16. Composite conductor containing superconductive wires

    Energy Technology Data Exchange (ETDEWEB)

    Larson, W.L.; Wong, J.

    1974-03-26

    A superconductor cable substitute made by coworking multiple rods of superconductive niobium--titanium or niobium--zirconium alloy with a common copper matrix to extend the copper and rods to form a final elongated product which has superconductive wires distributed in a reduced cross-section copper conductor with a complete metallurgical bond between the normal-conductive copper and the superconductor wires contained therein is described. The superconductor cable can be in the form of a tube.

  17. Topology Optimized Photonic Wire Splitters

    DEFF Research Database (Denmark)

    Frandsen, Lars Hagedorn; Borel, Peter Ingo; Jensen, Jakob Søndergaard;

    2006-01-01

    Photonic wire splitters have been designed using topology optimization. The splitters have been fabricated in silicon-on-insulator material and display broadband low-loss 3dB splitting in a bandwidth larger than 100 nm.......Photonic wire splitters have been designed using topology optimization. The splitters have been fabricated in silicon-on-insulator material and display broadband low-loss 3dB splitting in a bandwidth larger than 100 nm....

  18. Mechanical properties of steel rope wires -– quality test assurance

    Directory of Open Access Journals (Sweden)

    Jaroslava Dečmanová

    2010-02-01

    Full Text Available We investigate the mechanical properties of wires of steel ropes by tests in accordance with rule in operation and valid regulation.There are specified values of minimal and maximum capacity or strenghts and values of minimal bendings and torsion in them. Minimalvalues of bendings and torsion are rated wire strenght, diameter and surface treatment dependent. It is suitable to use the calculationof irregularity coefficient of steel wires strenght for quality assessment of steel ropes which put into practice soviet authors Žitkovand Pospechov. Statistical methods make possible to review the quality of steel ropes from the test results of their wires on capacity,bending and torsion. In the paper we evaluate and compare the quality of two steel ropes with triangular strands, we appear fromprotocols about their tests in the accredited testing station of steel ropes of our workstation.

  19. Detection System Design of Electric Vehicle Wiring Harness

    Institute of Scientific and Technical Information of China (English)

    SUN Jian-Xin; LI Xiao-Peng

    2015-01-01

    This paper introduces a method of harness testing system for electric vehicle wiring harness wiring .The system has implemented some commonly used electric wiring harness state detection using the way of the upper machine and lower machine communicate with each other, Such as normal, open circuit, short circuit, fault, etc. And then the lower machine send the wiring harness status to the upper machine, and then the upper machine parses the line state, and at the same time shows the test results, And then stores the test results in the database. After all, we can call at any time to check the date and the results of detection. It changes the traditional manual test mode of operation and Implements the detection process of automation and intellectualization.

  20. 1 mil gold bond wire study.

    Energy Technology Data Exchange (ETDEWEB)

    Huff, Johnathon; McLean, Michael B.; Jenkins, Mark W.; Rutherford, Brian Milne

    2013-05-01

    In microcircuit fabrication, the diameter and length of a bond wire have been shown to both affect the current versus fusing time ratio of a bond wire as well as the gap length of the fused wire. This study investigated the impact of current level on the time-to-open and gap length of 1 mil by 60 mil gold bond wires. During the experiments, constant current was provided for a control set of bond wires for 250ms, 410ms and until the wire fused; non-destructively pull-tested wires for 250ms; and notched wires. The key findings were that as the current increases, the gap length increases and 73% of the bond wires will fuse at 1.8A, and 100% of the wires fuse at 1.9A within 60ms. Due to the limited scope of experiments and limited data analyzed, further investigation is encouraged to confirm these observations.