Development and Sliding Wear Response of Epoxy Composites Filled with Coal Mine Overburden Material

Science.gov (United States)

Das, Prithika; Satapathy, Alok; Mishra, M. K.

2018-03-01

The paper reports on development and characterization of epoxy based composites filled with micro-sized mine overburden material. Coal mine overburden material is typically highly heterogeneous and is considered as waste material. For excavating each ton of coal, roughly 5 tons of overburden materials are removed and is dumped nearby occupying large space. Gainful utilization of this waste is a major challenge. In the present work, this material is used as filler materials in making a new class of epoxy matrix composites. Composites with different weight proportions of fillers (0, 10, 20, 30 and 40) wt. % are prepared by hand layup technique. Compression tests are performed as per corresponding ASTM standards to assess the compressive strength of these composites. Further, dry sliding tests are performed following ASTM G99 standards using a pin on disk machine. A design of experiment approach based on Taguchi’s L16 orthogonal arrays is adopted. Tests are performed at different sliding velocities for multiple sliding distances under varying normal loads. Specific wear rates of the composites under different test conditions are obtained. The analysis of the test results revealed that the filler content and the sliding velocity are the most predominant control factors affecting the wear rate. This work thus, opens up a new avenue for the value added utilization of coal mine overburden material.

Chromatographic methods and techniques used in studies of coals, their progenitors and coal-derived materials

Energy Technology Data Exchange (ETDEWEB)

Zubkova, Valentina [Jan Kochanowski University of Humanities and Sciences, Institute of Chemistry, Kielce (Poland)

2011-03-15

The use of chromatography in studies of coals, their progenitors and coal-related products was reviewed. The specificity of the coal structure was discussed. The use of extraction in preparing study samples was discussed paying special attention to the occurrence of undesirable phenomena such as aggregation of coal derivate molecules, resulting from the formation of their dimers and trimers, and degradation of polar solvents at temperatures above 350 C. The following ways of fractionating samples of coal materials were considered: thermal, solvent, column with the use of preparative size exclusive chromatography and preparative thin layer chromatography as well as membrane separation. The use of chromatography coupled with experimental techniques such as mass spectrometry, infrared spectroscopy, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry and pyrolysis was analysed. (orig.)

Center for Coal-Derived Low Energy Materials for Sustainable Construction

Energy Technology Data Exchange (ETDEWEB)

Jewell, Robert; Robl, Tom; Rathbone, Robert

2012-06-30

The overarching goal of this project was to create a sustained center to support the continued development of new products and industries that manufacture construction materials from coal combustion by-products or CCB’s (e.g., cements, grouts, wallboard, masonry block, fillers, roofing materials, etc). Specific objectives includes the development of a research kiln and associated system and the formulation and production of high performance low-energy, low-CO2 emitting calcium sulfoaluminate (CAS) cement that utilize coal combustion byproducts as raw materials.

Coal combustion products in Europe valuable raw materials for the construction industry

Energy Technology Data Exchange (ETDEWEB)

Berg, W. vom; Feuerborn, H.J. [European Coal Combustion Products Association e.V., Essen (Germany)

2005-07-01

Coal combustion products (CCPs) are formed with the production of electricity in coal-fired power plants. The production of these CCPs has been increased by the years due to legal requirements for flue gas cleaning. The utilisation of CCPS is well is established in some European countries, based on long term experience and technical as well as environmental benefits. As CCPs are defined as waste materials by existing legislation the power industry has to handle the stigma put on the products and hamper the beneficial use. (orig.)

External cost of coal based electricity generation: A tale of Ahmedabad city

International Nuclear Information System (INIS)

Mahapatra, Diptiranjan; Shukla, Priyadarshi; Dhar, Subash

2012-01-01

Electricity production causes unintended impacts. Their exclusion by the market leads to suboptimal resource allocations. Monetizing and internalizing of external costs, though challenging and debatable, leads to a better allocation of economic resources and welfare. In this paper, a life-cycle analysis (LCA) on the production of electricity from conventional coal based electricity generation system has been performed in order to examine the environmental impacts of coal based electricity generating systems in the twin-city of Ahmedabad and Gandhinagar in western India. By using dose–response functions, we make an attempt to estimate the damages to human health, crops, and building materials resulting from the operation of coal power plants and its associated mines. Further, we use geographic information system to account for spatially dependent data. Finally, monetary values have been assigned to estimate the damage to human health, crops and building materials. This study reveals that the health as well as on non-health impacts of air pollution resulting from coal based electricity generation may not be ignored both in absolute as well as economic value terms. Highlights: ► External cost from coal power generating systems has been calculated. ► We use LCA approach to monetize externalities. ► Geographic information software has been used to account for spatially dependent data. ► This study monetizes damages only to human health, crops, and building materials. ► We finally recommend policy directions to arrest this externality.

Relative radiation hazards of coal based and nuclear power plants

International Nuclear Information System (INIS)

Mishra, U.C.

1983-04-01

Coal, like most materials found in nature, contains trace quantities of naturally occurring radionuclides. However, low concentrations may become important if large quantities of coal are burnt in thermal power plants. Therefore a study was performed to determine the radioactivity in coal, in fly-ash and slag and assess the importance of radioactive emissions from thermal power plants. The results were compared to the radiological impact of nuclear power stations. Based on these data, theoretical estimates for the population living within 80km from power stations indicate that the collective dose commitments of coal-fired plants are one order of magnitude higher than those for BWR-type nuclear plants. Measurements taken in the vicinity of coal-fired plants were comparable to those for nuclear plants, i.e. within the range of variation of natural background radiation in India

Current results of coal gasification materials research at GRI

International Nuclear Information System (INIS)

Hill, V.L.; Barone, S.P.; Meyer, H.S.

1984-01-01

Corrosion, erosion/corrosion and mechanical property testing of commercial available materials in coal gasification atmospheres has been supported by the Gas Research Institute (GRI) since 1978. Recent corrosion data developed in the program for gasification and methanation technologies under development by GRI are presented. A brief discussion of typical results of long-term stress-rupture tests in coal gasification atmospheres is included

Activated, coal-based carbon foam

Science.gov (United States)

Rogers, Darren Kenneth; Plucinski, Janusz Wladyslaw

2004-12-21

An ablation resistant, monolithic, activated, carbon foam produced by the activation of a coal-based carbon foam through the action of carbon dioxide, ozone or some similar oxidative agent that pits and/or partially oxidizes the carbon foam skeleton, thereby significantly increasing its overall surface area and concurrently increasing its filtering ability. Such activated carbon foams are suitable for application in virtually all areas where particulate or gel form activated carbon materials have been used. Such an activated carbon foam can be fabricated, i.e. sawed, machined and otherwise shaped to fit virtually any required filtering location by simple insertion and without the need for handling the "dirty" and friable particulate activated carbon foam materials of the prior art.

Characterization and supply of coal based fuels

Energy Technology Data Exchange (ETDEWEB)

1992-06-01

Studies and data applicable for fuel markets and coal resource assessments were reviewed and evaluated to provide both guidelines and specifications for premium quality coal-based fuels. The fuels supplied under this contract were provided for testing of advanced combustors being developed under Pittsburgh Energy Technology Center (PETC) sponsorship for use in the residential, commercial and light industrial (RCLI) market sectors. The requirements of the combustor development contractors were surveyed and periodically updated to satisfy the evolving needs based on design and test experience. Available coals were screened and candidate coals were selected for further detailed characterization and preparation for delivery. A team of participants was assembled to provide fuels in both coal-water fuel (CWF) and dry ultrafine coal (DUC) forms. Information about major US coal fields was correlated with market needs analysis. Coal fields with major reserves of low sulfur coal that could be potentially amenable to premium coal-based fuels specifications were identified. The fuels requirements were focused in terms of market, equipment and resource constraints. With this basis, the coals selected for developmental testing satisfy the most stringent fuel requirements and utilize available current deep-cleaning capabilities.

Development and linearization of generalized material balance equation for coal bed methane reservoirs

International Nuclear Information System (INIS)

Penuela, G; Ordonez R, A; Bejarano, A

1998-01-01

A generalized material balance equation was presented at the Escuela de Petroleos de la Universidad Industrial de Santander for coal seam gas reservoirs based on Walsh's method, who worked in an analogous approach for oil and gas conventional reservoirs (Walsh, 1995). Our equation was based on twelve similar assumptions itemized by Walsh for his generalized expression for conventional reservoirs it was started from the same volume balance consideration and was finally reorganized like Walsh (1994) did. Because it is not expressed in terms of traditional (P/Z) plots, as proposed by King (1990), it allows to perform a lot of quantitative and qualitative analyses. It was also demonstrated that the existent equations are only particular cases of the generalized expression evaluated under certain restrictions. This equation is applicable to coal seam gas reservoirs in saturated, equilibrium and under saturated conditions, and to any type of coal beds without restriction on especial values of the constant diffusion

Preparation of sintered foam materials by alkali-activated coal fly ash.

Science.gov (United States)

Zhao, Yelong; Ye, Junwei; Lu, Xiaobin; Liu, Mangang; Lin, Yuan; Gong, Weitao; Ning, Guiling

2010-02-15

Coal fly ash from coal fired power stations is a potential raw material for the production of ceramic tiles, bricks and blocks. Previous works have demonstrated that coal fly ash consists mainly of glassy spheres that are relatively resistant to reaction. An objective of this research was to investigate the effect of alkali on the preparation process of the foam material. Moreover, the influence of foam dosage on the water absorption, apparent density and compressive strength was evaluated. The experimental results showed that homogenous microstructures of interconnected pores could be obtained by adding 13 wt.% foaming agent at 1050 degrees C, leading to foams presenting water absorption, apparent density and compressive strength values of about 126.5%, 0.414 g/cm(3), 6.76 MPa, respectively.

Combustion characterization of beneficiated coal-based fuels

Energy Technology Data Exchange (ETDEWEB)

Chow, O.K.; Levasseur, A.A.

1995-11-01

The Pittsburgh Energy Technology Center (PETC) of the U.S. Department of Energy is sponsoring the development of advanced coal-cleaning technologies aimed at expanding the use of the nation`s vast coal reserves in an environmentally and economically acceptable manner. Because of the lack of practical experience with deeply beneficiated coal-based fuels, PETC has contracted Combustion Engineering, Inc. to perform a multi-year project on `Combustion Characterization of Beneficiated Coal-Based Fuels.` The objectives of this project include: (1) the development of an engineering data base which will provide detailed information on the properties of Beneficiated Coal-Based Fuels (BCs) influencing combustion, ash deposition, ash erosion, particulate collection, and emissions; and (2) the application of this technical data base to predict the performance and economic impacts of firing the BCFs in various commercial boiler designs.

Steam Turbine Materials for Ultrasupercritical Coal Power Plants

Energy Technology Data Exchange (ETDEWEB)

Viswanathan, R.; Hawk, J.; Schwant, R.; Saha, D.; Totemeier, T.; Goodstine, S.; McNally, M.; Allen, D. B.; Purgert, Robert

2009-06-30

The Ultrasupercritical (USC) Steam Turbine Materials Development Program is sponsored and funded by the U.S. Department of Energy and the Ohio Coal Development Office, through grants to Energy Industries of Ohio (EIO), a non-profit organization contracted to manage and direct the project. The program is co-funded by the General Electric Company, Alstom Power, Siemens Power Generation (formerly Siemens Westinghouse), and the Electric Power Research Institute, each organization having subcontracted with EIO and contributing teams of personnel to perform the requisite research. The program is focused on identifying, evaluating, and qualifying advanced alloys for utilization in coal-fired power plants that need to withstand steam turbine operating conditions up to 760°C (1400°F) and 35 MPa (5000 psi). For these conditions, components exposed to the highest temperatures and stresses will need to be constructed from nickel-based alloys with higher elevated temperature strength than the highchromium ferritic steels currently used in today's high-temperature steam turbines. In addition to the strength requirements, these alloys must also be weldable and resistant to environmental effects such as steam oxidation and solid particle erosion. In the present project, candidate materials with the required creep strength at desired temperatures have been identified. Coatings that can resist oxidation and solid particle erosion have also been identified. The ability to perform dissimilar welds between nickel base alloys and ferritic steels have been demonstrated, and the properties of the welds have been evaluated. Results of this three-year study that was completed in 2009 are described in this final report. Additional work is being planned and will commence in 2009. The specific objectives of the future studies will include conducting more detailed evaluations of the weld-ability, mechanical properties and repair-ability of the selected candidate alloys for rotors

Economics of coal-based electricity generation

Energy Technology Data Exchange (ETDEWEB)

Hemming, D F; Johnston, R; Teper, M

1979-01-01

The report deals with base-load electricity generation from coal and compares the economics of four alternative technologies: conventional pulverised-fuel (PF) boiler with steam cycle; atmospheric fluidised-bed (AFB) boiler with steam cycle; pressurised fluidised-bed (PFB) boiler with combined cycle; and integrated air-blown coal gasification with combined cycle systems are compared for both a high sulphur (3.5%) coal with environmental regulations requiring 85% sulphur removal, and for a low sulphur coal without sulphur removal. The results indicate that there is no single clear 'winner' among the advanced technologies. The optimum system depends on coal price, required rate-of-return, sulphur content of the coal, taxation regime etc. (34 refs.) (Available from IEA Coal Research, Economic Assessment Service)

The production of high load coal-water mixtures on the base of Kansk-Achinsk Coal Basin

Energy Technology Data Exchange (ETDEWEB)

Demidov, Y.; Bruer, G.; Kolesnikova, S. [Research and Design Institute for Problems of Development of Kansk-Achinsk Coal Basin (KATEKNilugol), Krasnoyarsk (Russian Federation)

1995-12-01

The results of the {open_quotes}KATEKNIIugol{close_quotes} work on the problems of high load coal-water mixtures are given in this article. General principles of the mixture production, short characteristics of Kansk-Achinsk coals, the experimental results of the coal mixture production on a test-industrial scale, the suspension preparation on the base of coal mixtures, technical-economical indexes of tested coal pipeline variants based on Kansk-Achinsk coals are described.

Connection between radon emanation and some structural properties of coal-slag as building material

International Nuclear Information System (INIS)

Somlai, J.; Jobbagy, V.; Somlai, K.; Kovacs, J.; Nemeth, Cs.; Kovacs, T.

2008-01-01

Radionuclides of natural origin may accumulate in different industrial waste materials and by-products. The use of coal bottom ash or coal-slag as building material in Hungary is widespread. Because of the elevated radium content of coal-slag, high radon concentration has been detected in buildings containing coal-slag as building material. In two towns, where buildings contain coal-slag with almost the same radium concentration, the indoor radon concentrations have been found to differ significantly. In order to investigate the cause of the difference in the emanation coefficients, slag samples from the two locations were examined for grain-size distribution, density, pore volume, and specific surface. The applied methods were: gamma spectrometry for the radium concentration of the samples; Lucas cell method for the radon emanation; nitrogen absorption-desorption isotherms analyzed using the BET theory and mercury poremeter for the specific surface and pore volume. It was found that the great difference in the emanation coefficients (1.35±0.13% and 14.3±0.92%) of the coal-slag samples is primarily influenced by the pore volume and the specific surface

Materials for coal conversion and utilization

Energy Technology Data Exchange (ETDEWEB)

None,

1981-01-01

The Sixth annual conference on materials for coal conversion and utilization was held October 13-15, 1981 at the National Bureau of Standards Gaithersburg, Maryland. It was sponsored by the US Department of Energy, the Electric Power Research Institute, the Gas Research Institute and the National Bureau of Standards. Fifty-eight papers from the proceedings have been entered individually into EDB and ERA; four papers had been entered previously from other sources. (LTN)

Nitrogen-enriched bituminous coal-based active carbons as materials for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

R. Pietrzak; K. Jurewicz; P. Nowicki; K. Babel; H. Wachowska [A. Mickiewicz University, Poznan (Poland). Laboratory of Coal Chemistry and Technology

2010-11-15

The paper presents the results of a study on obtaining N-enriched active carbons from bituminous coal and on testing its use as an electrode material in supercapacitors. The coal was carbonised, activated with KOH and ammoxidised by a mixture of ammonia and air at the ratio 1:3 at 300{sup o}C or 350{sup o}C, at different stages of the production, that is, at those of precursor, carbonisate, and active carbon. The products were microporous N-enriched active carbon samples of well-developed surface area reaching from 1577 to 2510 m{sup 2}/g and containing 1.0 to 8.5 wt% of nitrogen. The XPS measurements have shown that in the active carbons enriched in nitrogen at the stage of precursor and at the stage of carbonisate, the dominant nitrogen species are the N-5 groups, while in the samples ammoxidised at the last stage of the treatment the dominant nitrogen species are the surface groups of imines and/or nitriles, probably accompanied by amines and amides. The paper reports the results of a comprehensive study of the effect of the structure and chemical composition of a series of active carbon samples of different properties on their capacity performance in water solutions of H{sub 2}SO{sub 4} or KOH, with the behaviour of positive and negative electrodes analysed separately. 33 refs., 7 figs., 8 tabs.

Investigating erosion of building materials used in an installation for pneumatic transport of coke breeze and coal

Energy Technology Data Exchange (ETDEWEB)

Bandrowski, J.; Kot-Borkowska, Z.; Misztal, M.; Raczek, J.; Kaczmarzyk, G.

1980-09-01

This article investigates the influence of the following factors on erosion of building material used in pneumatic transport of coal and coke breeze: intensity of coal or coke breeze flow within the range of 47 to 120 kg/h for coke and 99 to 165 kg/h for coal; speed of solid material particles within the range 3.71 to 7.97 m/s for coke, and 3.30 to 7.58 m/s for coal; duration of the experiments 0.5 to 1.5 h for coke and 2.0 to 5.0 for coal; angle of inclination of the sample of building material 30 to 60 degrees for both coal and coke breeze. Three types of construction material used in pneumatic transport were tested: steel, concrete and chamotte bricks. Investigations show that concrete is characterized by the highest erosion, chamotte bricks by medium erosion and steel by the lowest erosion. As a result of mathematical processing of experimental data, empirical models of erosion of the three materials are constructed. (7 refs.)

Techno-Economic Analysis of Scalable Coal-Based Fuel Cells

Energy Technology Data Exchange (ETDEWEB)

Chuang, Steven S. C. [Univ. of Akron, OH (United States)

2014-08-31

Researchers at The University of Akron (UA) have demonstrated the technical feasibility of a laboratory coal fuel cell that can economically convert high sulfur coal into electricity with near zero negative environmental impact. Scaling up this coal fuel cell technology to the megawatt scale for the nation’s electric power supply requires two key elements: (i) developing the manufacturing technology for the components of the coal-based fuel cell, and (ii) long term testing of a kW scale fuel cell pilot plant. This project was expected to develop a scalable coal fuel cell manufacturing process through testing, demonstrating the feasibility of building a large-scale coal fuel cell power plant. We have developed a reproducible tape casting technique for the mass production of the planner fuel cells. Low cost interconnect and cathode current collector material was identified and current collection was improved. In addition, this study has demonstrated that electrochemical oxidation of carbon can take place on the Ni anode surface and the CO and CO₂ product produced can further react with carbon to initiate the secondary reactions. One important secondary reaction is the reaction of carbon with CO₂ to produce CO. We found CO and carbon can be electrochemically oxidized simultaneously inside of the anode porous structure and on the surface of anode for producing electricity. Since CH₄ produced from coal during high temperature injection of coal into the anode chamber can cause severe deactivation of Ni-anode, we have studied how CH₄ can interact with CO₂ to produce in the anode chamber. CO produced was found able to inhibit coking and allow the rate of anode deactivation to be decreased. An injection system was developed to inject the solid carbon and coal fuels without bringing air into the anode chamber. Five planner fuel cells connected in a series configuration and tested. Extensive studies on the planner fuels

Characterization and supply of coal-based fuels

Energy Technology Data Exchange (ETDEWEB)

1989-06-01

Contract objectives are as follows: Develop fuel specifications to serve combustor requirements. Select coals having appropriate compositional and quality characteristics as well as an economically attractive reserve base; Provide quality assurance for both the parent coals and the fuel forms; and deliver premium coal-based fuels to combustor developers as needed for their contract work. Progress is discussed, particulary in slurry fuel preparation and particle size distribution.

Approaches for controlling air pollutants and their environmental impacts generated from coal-based electricity generation in China.

Science.gov (United States)

Xu, Changqing; Hong, Jinglan; Ren, Yixin; Wang, Qingsong; Yuan, Xueliang

2015-08-01

This study aims at qualifying air pollutants and environmental impacts generated from coal-based power plants and providing useful information for decision makers on the management of coal-based power plants in China. Results showed that approximately 9.03, 54.95, 62.08, and 12.12% of the national carbon dioxide, sulfur dioxide, nitrogen oxides, and particulate matter emissions, respectively, in 2011were generated from coal-based electricity generation. The air pollutants were mainly generated from east China because of the well-developed economy and energy-intensive industries in the region. Coal-washing technology can simply and significantly reduce the environmental burden because of the relativity low content of coal gangue and sulfur in washed coal. Optimizing the efficiency of raw materials and energy consumption is additional key factor to reduce the potential environmental impacts. In addition, improving the efficiency of air pollutants (e.g., dust, mercury, sulfur dioxide, nitrogen oxides) control system and implementing the strict requirements on air pollutants for power plants are important ways for reducing the potential environmental impacts of coal-based electricity generation in China.

Novel Fuel Cells for Coal Based Systems

Energy Technology Data Exchange (ETDEWEB)

Thomas Tao

2011-12-31

The goal of this project was to acquire experimental data required to assess the feasibility of a Direct Coal power plant based upon an Electrochemical Looping (ECL) of Liquid Tin Anode Solid Oxide Fuel Cell (LTA-SOFC). The objective of Phase 1 was to experimentally characterize the interaction between the tin anode, coal fuel and cell component electrolyte, the fate of coal contaminants in a molten tin reactor (via chemistry) and their impact upon the YSZ electrolyte (via electrochemistry). The results of this work will provided the basis for further study in Phase 2. The objective of Phase 2 was to extend the study of coal impurities impact on fuel cell components other than electrolyte, more specifically to the anode current collector which is made of an electrically conducting ceramic jacket and broad based coal tin reduction. This work provided a basic proof-of-concept feasibility demonstration of the direct coal concept.

Clean coal technology and advanced coal-based power plants

International Nuclear Information System (INIS)

Alpert, S.B.

1991-01-01

Clean Coal Technology is an arbitrary terminology that has gained increased use since the 1980s when the debate over acid raid issues intensified over emissions of sulfur dioxide and nitrogen oxides. In response to political discussions between Prime Minister Brian Mulroney of Canada and President Ronald Reagan in 1985, the US government initiated a demonstration program by the Department of Energy (DOE) on Clean Coal Technologies, which can be categorized as: 1. precombustion technologies wherein sulfur and nitrogen are removed before combustion, combustion technologies that prevent or lower emissions as coal is burned, and postcombustion technologies wherein flue gas from a boiler is treated to remove pollutants, usually transforming them into solids that are disposed of. The DOE Clean Coal Technology (CCT) program is being carried out with $2.5 billion of federal funds and additional private sector funds. By the end of 1989, 38 projects were under way or in negotiation. These projects were solicited in three rounds, known as Clean Coal I, II, and III, and two additional solicitations are planned by DOE. Worldwide about 100 clean coal demonstration projects are being carried out. This paper lists important requirements of demonstration plants based on experience with such plants. These requirements need to be met to allow a technology to proceed to commercial application with ordinary risk, and represent the principal reasons that a demonstration project is necessary when introducing new technology

Material Properties and Characteristics for Development of an Expert System for Coal-Tar Sealers

National Research Council Canada - National Science Library

Shoenberger, James

2001-01-01

.... Several coal-tar mixtures that varied with source of the coal-tar emulsion, amount of aggregate, and amount of polymer used in the mixtures were evaluated for their field performance and material properties...

Observer-based Coal Mill Control using Oxygen Measurements

DEFF Research Database (Denmark)

Andersen, Palle; Bendtsen, Jan Dimon; S., Tom

2006-01-01

This paper proposes a novel approach to coal flow estimation in pulverized coal mills, which utilizes measurements of oxygen content in the flue gas. Pulverized coal mills are typically not equipped with sensors that detect the amount of coal injected into the furnace. This makes control...... of the coal flow difficult, causing stability problems and limits the plant's load following capabilities. To alleviate this problem without having to rely on expensive flow measurement equipment, a novel observer-based approach is investigated. A Kalman filter based on measurements of combustion air flow led...... into the furnace and oxygen concentration in the flue gas is designed to estimate the actual coal flow injected into the furnace. With this estimate, it becomes possible to close an inner loop around the coal mill itself, thus giving a better disturbance rejection capability. The approach is validated against...

Role of coal combustion products in sustainable construction materials

Energy Technology Data Exchange (ETDEWEB)

Naik, T.R.; Siddique, R.; Vaniker, S. [University of Wisconsin-Milwaukee, Milwaukee, WI (USA). UWM Center for Products Utilization, College of Engineering and Applied Science

2003-07-01

The paper describes various coal combustion products, CCPs produced in the process of power generation. These include fly ash, bottom ash, boiler slag and flue gas desulfurization products. Typical test protocol used for testing, analysis and evaluation of CCPs, as well as the current best recycling use options for these materials are discussed. Materials, productions, properties, and potential applications in the manufacture of emerging materials for sustainable construction, as well as environmental impact are also briefly discussed. 47 refs., 16 figs., 8 tabs.

Problems of coal-based power generation

International Nuclear Information System (INIS)

Noskievic, P.

1996-01-01

Current problems of and future trends in coal-based power generation are discussed. The present situation is as follows: coal, oil and gas contribute to world fossil fuel resources 75%, 14%, and 11%, respectively, and if the current trend will continue, will be depleted in 240, 50, and 60 years, respectively; the maximum resource estimates (including resources that have not yet been discovered) are 50% higher for oil and 100% higher for gas, for coal such estimates have not been made. While the world prices of coal are expected to remain virtually constant, the prices of gas will probably increase to be twice as high in 2010. Thus, the role of coal may be higher in the next century than it is now, provided that due attention is paid to improving the efficiency of coal-fired power plants and reducing their adverse environmental effects. A comparison of economic data for coal-fired and gas-fired power plants is as follows: Investment cost (USD/kW): 1400, 800; fixed running cost (USD/kW.y): 33.67, 9.0; variable running cost (USD/kWh): 0.30, 0.15; power use (kJ/kWh): 10.29, 7.91; annual availability (%): 70, 50; fuel price (USD/GJ): 1.00, 4.30; power price (USD/kWh): 4.28, 5.52. The investment cost for coal-fired plants covers new construction including flue gas purification. The integrated gasification combined cycle (IGCC) seems to be the future of coal-based power generation. The future problems to be addressed include ways to reduce air pollution, improving the efficiency of the gas-steam cycle, and improving the combustion process particularly with a view to reducing substantially its environmental impact. (P.A.). 4 figs., 4 tabs., 9 refs

Annotated bibliography of methods for determining sulfur and forms of sulfur in coal and coal-related materials

Energy Technology Data Exchange (ETDEWEB)

Chriswell, C.D.; Norton, G.A.; Akhtar, S.S.; Straszheim, W.E.; Markuszewski, R.

1993-01-01

Over 400 published papers, presentations at scientific meetings, and reports relating to the determination of sulfur and sulfur forms in coal-related materials have been accumulated, classified, and an evaluation made of their content.

Analysis of radioactivity concentration in naturally occurring radioactive materials used in coal-fired plants in Korea

Energy Technology Data Exchange (ETDEWEB)

Kim, Yong Geom; Kim, Si Young; Ji, Seung Woo; Park, Il; Kim, Min Jun; Kim, Kwang Pyo [Dept. of Nuclear Engineering, Kyung Hee University, Yongin (Korea, Republic of)

2017-02-15

Coals and coal ashes, raw materials and by-products, in coal-fired power plants contain naturally occurring radioactive materials (NORM). They may give rise to internal exposure to workers due to inhalation of airborne particulates containing radioactive materials. It is necessary to characterize radioactivity concentrations of the materials for assessment of radiation dose to the workers. The objective of the present study was to analyze radioactivity concentrations of coals and by-products at four coal-fired plants in Korea. High purity germanium detector was employed for analysis of uranium series, thorium series, and potassium 40 in the materials. Radioactivity concentrations of {sup 226}Ra, {sup 228}Ra, and {sup 40}K were 2⁓53 Bq kg{sup -1}, 3⁓64 Bq kg{sup -1}, and 14⁓431 Bq kg{sup -1} respectively in coal samples. For coal ashes, the radioactivity concentrations were 77⁓133 Bq kg{sup -1}, 77⁓105 Bq kg{sup -1}, and 252⁓372 Bq kg{sup -1} in fly ash samples and 54⁓91 Bq kg{sup -1}, 46⁓83 Bq kg{sup -1}, and 205⁓462 Bq kg{sup -1} in bottom ash samples. For flue gas desulfurization (FGD) gypsum, the radioactivity concentrations were 3⁓5 Bq kg{sup -1}, 2⁓3 Bq kg{sup -1}, and 22⁓47 Bq kg{sup -1}. Radioactivity was enhanced in coal ash compared with coal due to combustion of organic matters in the coal. Radioactivity enhancement factors for {sup 226}Ra, {sup 228}Ra, and {sup 40}K were 2.1⁓11.3, 2.0⁓13.1, and 1.4⁓7.4 for fly ash and 2.0⁓9.2, 2.0⁓10.0, 1.9⁓7.7 for bottom ash. The database established in this study can be used as basic data for internal dose assessment of workers at coal-fred power plants. In addition, the findings can be used as a basic data for development of safety standard and guide of Natural Radiation Safety Management Act.

Possibilities of nondestructive determination of fluorine in coal and biological materials by IPAA

International Nuclear Information System (INIS)

Randa, Zdenek; Mizera, Jiri; Chvatil, David

2009-01-01

The possibilities of nondestructive determination of fluorine in coal and biological materials by instrumental photon activation analysis (IPAA) were studied. The determination was based on counting the non-specific 511 keV annihilation gamma rays of 18 F, a pure positron emitter which is the product of the photonuclear reaction 19 F(γ, n) 18 F. The simultaneous formation of some additional positron emitters, particularly 45 Ti and 34m Cl, is an interfering factor. When using correction standards for Ti and Cl and optimization of the beam energy and irradiation-decay-counting times, fluorine could be determined by IPAA in selected coal and biological samples at the ten ppm level. The feasibility of additional optimization for further improvements of the proposed IPAA procedure are discussed

Environmental impact of coal utilization (from raw material to waste resources): Proceedings

International Nuclear Information System (INIS)

Sahu, K.C.

1991-10-01

The proceedings contains 27 papers presented at the conference on environmental impact of coal utilization from raw material to waste resources which was held at the Indian Institute of Technology, Bombay, during 14-15 January 1991. The conference was held as a follow-up of the research project to study the impact of coal utilization. The project was undertaken jointly by the Indian Institute of Technology, Bombay and the University of Western Ontario, Canada. The project was funded by the International Development Research Centre, Ottawa (Canada). The principle themes of the conference were : occurrence of trace elements in coal, fate of trace elements during combustion of coal, characterisation of fly ash and its properties and utilization, and environmental impact of ash disposal. (M.G.B.)

Coal blending preparation for non-carbonized coal briquettes

Science.gov (United States)

Widodo; Fatimah, D.; Estiaty, L. M.

2018-02-01

Referring to the national energy policy targets for the years 2025, the government has launched the use of coal briquettes as an alternative energy replacement for kerosene and firewood. Non-carbonized briquettes in the form of coal briquettes as well as bio-coal briquettes are used in many small-medium industries and households, and are rarely used by large industries. The standard quality of coal briquettes used as raw material for non-carbonized briquettes is a minimum calorific value of 4,400 kcal/kg (adb); total sulfur at a maximum of 1% (adb), and water content at plants), the environment of deposition, and the geological conditions of the surrounding area, so that the coal deposits in each region will be different as well as the amount and also the quality. Therefore, the quantity and the quality of coal in each area are different to be eligible in the making of briquettes to do blending. In addition to the coal blending, it is also necessary to select the right materials in the making of coal briquettes and bio-coal briquettes. The formulation of the right mixture of material in the making of briquettes, can be produced of good quality and environmental friendly.

The Czech base of hard coal, problems, possibilities for utilization

International Nuclear Information System (INIS)

Cermak, T.; Roubicek, V.

1993-01-01

The Czech coal and power engineering base is in a deep restructuring period now. The basic problems represents the changeover from the system of the centrally planned state economy to the market model of the energy resources mining, production and consumption. The Czech economy will have to face to up to now unknown competitive forces on the coal market in Europe where American, Canadian, Australian and South African coals compete. The paper discusses historical aspects of the development of the coal mining industry in the Czechoslavakia, the present coal preparation techniques for coking coals, the coking industry, and the utilization of brown coal. How to utilize the domestic coal base and coal generally is closely connected with the global restructuralization of the Czech economy. The most difficult step of this process is undoubtedly the adaptation of the Czech fuel and energy base to the market economy conditions

Reclamation technology development for western Arkansas coal refuse waste materials

International Nuclear Information System (INIS)

King, J.R.; Veith, D.L.

1994-01-01

Coal mining has been an important industry in the Arkansas River Valley Major Land Resource Area (MLRA) of western Arkansas for more than 100 yr., most of it with little regard for environmental concerns. Almost 3,640 ha. of land affected by surface coal mines cover the seven-county area, with less than 1,200 ha. currently in various stages of operation or reclamation. Since only the active mining sites must now be reclaimed by law, the remaining 2,440 ha. of abandoned land remains at the mercy of natural forces. Little topsoil exists on these sites and the coal wastes are generally acidic with a pH in the 4.0-5.5 range. Revegetation attempts under these conditions generally require continued maintenance and retreatment until an acceptable cover is achieved. If and when an acceptable vegetative cover is established, the cost frequently approaches $7,400/ha. ($3,000/acre). In an effort to resolve these issues and provide some direction for stabilizing coal waste lands, the US Department of Agriculture through its Soil Conservation Service Plant Materials Center at Boonville, Arkansas, received a Congressional Pass through administered by the US Bureau of Mines, to support a 5-yr. revegetation study on the coal mine spoils of western Arkansas. This paper reports the results through the spring of 1994 on that portion of the study dealing with the establishment of blackberries as a cash crop on coal mine spoils

Coal Ash Corrosion Resistant Materials Testing

Energy Technology Data Exchange (ETDEWEB)

D. K. McDonald; P. L. Daniel; D. J. DeVault

2007-12-31

In April 1999, three identical superheater test sections were installed into the Niles Unit No.1 for the purpose of testing and ranking the coal ash corrosion resistance of candidate superheater alloys. The Niles boiler burns high sulfur coal (3% to 3.5%) that has a moderate alkali content (0.2% sodium equivalents), thus the constituents necessary for coal ash corrosion are present in the ash. The test sections were controlled to operate with an average surface metal temperature from approximately 1060 F to 1210 F which was within the temperature range over which coal ash corrosion occurs. Thus, this combination of aggressive environment and high temperature was appropriate for testing the performance of candidate corrosion-resistant tube materials. Analyses of the deposit and scale confirmed that aggressive alkali sulfate constituents were present at the metal surface and active in tube metal wastage. The test sections were constructed so that the response of twelve different candidate tube and/or coating materials could be studied. The plan was to remove and evaluate one of the three test sections at time intervals of 1 year, 3 years, and 5 years. This would permit an assessment of performance of the candidate materials as a function of time. Test Section A was removed in November 2001 after about 24 months of service at the desired steam temperature set point, with about 15.5 months of exposure at full temperature. A progress report, issued in October 2002, was written to document the performance of the candidate alloys in that test section. The evaluation described the condition of each tube sample after exposure. It involved a determination of the rate of wall thickness loss for these samples. In cases where there was more than one sample of a candidate material in the test section, an assessment was made of the performance of the alloy as a function of temperature. Test Sections B and C were examined during the November 2001 outage, and it was decided that

Evaluation of pitches and cokes from solvent-extracted coal materials

Energy Technology Data Exchange (ETDEWEB)

McHenry, E.R.

1996-12-01

Three initial coal-extracted (C-E) samples were received from the West Virginia University (WVU) Chemical Engineering Department. Two samples had been hydrogenated to obtain pitches that satisfy Theological requirements. One of the hydrogenated (HC-E) samples had been extracted by toluene to remove ash and higher molecular weight aromatic compounds. We were unable to measure the softening point and viscosity of the non-hydro treated solid extract sample, Positive characteristics in the HC-E materials were softening points of 113-119{degrees}C, low sulfur and ash. The oxygen and nitrogen content of the HC-E samples may limit future usage in premium carbon and graphite products. Coking values were similar to petroleum pitches. Laboratory anode testing indicates that in combination with standard coal-tar pitch, the HC-E material can be used as a binder pitch.

Experimental research on combustion fluorine retention using calcium-based sorbents during coal combustion (II)

Energy Technology Data Exchange (ETDEWEB)

Qi, Q.; Ma, X.; Liu, J.; Wu, X.; Zhou, J.; Cen, K. [Liaoning Technical University, Fuxin (China). College of Resource and Environment Engineering

2008-12-15

Fluoride pollution produced by coal burning can be controlled with the calcium-based sorbent combustion fluorine technique in which calcium-based sorbents are mixed with the coal or sprayed into the combustion chamber. In a fixed bed tube furnace combustion experiment using one calcium-based natural mineral, limestone and one calcium-based building material, it was shown that the calcium-based sorbent particle grain size and pore structure have a big influence on the combustion fluorine retention effect. Reducing the calcium-based sorbent particle grain size and improving the calcium sorbent structure characteristics at very high temperature to enhance the fluorine retention effect is the important approach to the fluorine retention agent development. 8 refs., 1 fig., 5 tabs.

Polycyclic aromatic hydrocarbons (PAHs) in a coal tar standard reference material - SRM 1597a updated

Energy Technology Data Exchange (ETDEWEB)

Wise, Stephen A.; Poster, Dianne L.; Rimmer, Catherine A.; Schubert, Patricia; Sander, Lane C.; Schantz, Michele M. [National Institute of Standards and Technology (NIST), Analytical Chemistry Division, Gaithersburg, MD (United States); Leigh, Stefan D. [National Institute of Standards and Technology (NIST), Statistical Engineering Division, Gaithersburg, MD (United States); Moessner, Stephanie [National Institute of Standards and Technology (NIST), Analytical Chemistry Division, Gaithersburg, MD (United States); GMP/Comparator Labs, Werthenstein Chemie AG, Industrie Nord, Schachen (Switzerland)

2010-09-15

SRM 1597 Complex Mixture of Polycyclic Aromatic Hydrocarbons from Coal Tar, originally issued in 1987, was recently reanalyzed and reissued as SRM 1597a with 34 certified, 46 reference, and 12 information concentrations (as mass fractions) for polycyclic aromatic hydrocarbons (PAHs) and polycyclic aromatic sulfur heterocycles (PASHs) including methyl-substituted PAHs and PASHs. The certified and reference concentrations (as mass fractions) were based on results of analyses of the coal tar material using multiple analytical techniques including gas chromatography/mass spectrometry on four different stationary phases and reversed-phase liquid chromatography. SRM 1597a is currently the most extensively characterized SRM for PAHs and PASHs. (orig.)

Characterization of Coal Quality Based On Ash Content From M2 Coal-Seam Group, Muara Enim Formation, South Sumatra Basin

Directory of Open Access Journals (Sweden)

Frillia Putri Nasution

2017-09-01

Full Text Available Muara Enim Formation is well known as coal-bearing formation in South Sumatra Basin. As coal-bearing formation, this formation was subjects of many integrated study. Muara Enim Formation can be divided into four coal-seam group, M1, M2, M3, and M4. The M2 group comprising of Petai (C, Suban (B, Lower Mangus (A2, and Upper Mangus (A1. Depositional environments of Group M2 is transitional lower delta plain with sub-depositional are crevasse splay and distributary channel. The differentiation of both sub-depositional environments can be caused the quality of coal deposit. One of quality aspects is ash content. This research conducted hopefully can give better understanding of relationship between depositional environments to ash content. Group M2 on research area were found only Seam C, Seam B, and Seam A2, that has distribution from north to central so long as 1400 m. Coal-seam thickness C ranged between 3.25-9.25 m, Seam B range 7.54-13.43 m, and Seam C range 1.53-8.37 m, where all of coal-seams thickening on the central part and thinning-splitting to northern part and southern part. The ash content is formed from burning coal residue material. Ash contents on coal seam caused by organic and inorganic compound which resulted from mixing modified material on surrounded when transportation, sedimentation, and coalification process. There are 27 sample, consists of 9 sample from Seam C, 8 sample from Seam B, and 10 sample from Seam A2. Space grid of sampling is 100-150 m. Ash content influenced by many factors, but in research area, main factor is existence of inorganic parting. Average ash content of Seam C is 6,04%, Seam B is 5,05%, and Seam A2 is 3,8%. Low ash content influenced by settle environment with minor detrital material. High ash content caused by oxidation and erosional process when coalification process. Ash content on coal in research area originated from detritus material carried by channel system into brackish area or originated

Aromatic raw materials from coal

Energy Technology Data Exchange (ETDEWEB)

Collin, G

1982-06-01

Liquid byproducts of coal carbonization meet some 25% of the world demand for aromatic chemicals, currently at approx. 30 million t/a, in particular 15% of the demand for benzene and over 95% of the demand for condensed aromatics and heteroaromatics. Industrial processing of the aromatic byproducts of coal pressure gasification is carried out to only a minor extent. Other methods that may be employed in future to obtain carbochemical aromatic compounds are solvolysis and supercritical gas extraction, the catalytic liquid-phase hydrogenation and hydropyrolysis of coal, which also permit recovery of benzene and homologues, phenols, and condensed and partially hydrogenated aromatics, and the synthesis of aromatics using methanol as the key compound. As with the present means of obtaining aromatic chemicals from coal, the processes that may in future be applied on an industrial scale to obtain pure aromatics will only be economically feasible if linked with the manufacture of other mass products and combined with the present production of carbochemical aromatics. (In German)

No switch to coal-based feedstocks until 2000

Energy Technology Data Exchange (ETDEWEB)

1977-06-10

This is a resume of a paper ''Organics for the 1980s-petrochemicals or coal chemicals'' by S. P. S. Andrew. There will be no significant switch from petrochemicals to coal-based chemicals worldwide until well into the 21st century, when synthetic gasoline could be made in the U. S. from open-cast coal. Processes are being developed for converting coal to gasoline, ethylene, and ammonia.

Analysis of material flow in a utillzation technology of low grade manganese ore and sulphur coal complementary

Science.gov (United States)

Wang, Bo-Zhi; Deng, Biao; Su, Shi-Jun; Ding, Sang-Lan; Sun, Wei-Yi

2018-03-01

Electrolytic manganese is conventionally produced through low-grade manganese ore leaching in SO2, with the combustion of high sulfur coal. Subsequently the coal ash and manganese slag, produced by the combustion of high sulfur coal and preparation of electrolytic manganese, can be used as raw ingredients for the preparation of sulphoaluminate cement. In order to realize the `coal-electricity-sulfur-manganese-building material' system of complementary resource utilization, the conditions of material inflow and outflow in each process were determined using material flow analysis. The material flow models in each unit and process can be obtained by analyzed of material flow for new technology, and the input-output model could be obtained. Through the model, it is possible to obtain the quantity of all the input and output material in the condition of limiting the quantity of a substance. Taking one ton electrolytic manganese as a basis, the quantity of other input material and cements can be determined with the input-output model. The whole system had thusly achieved a cleaner production level. Therefore, the input-output model can be used for guidance in practical production.

Rice Seedling Substrate Produced by Coal Gangue

Directory of Open Access Journals (Sweden)

SHAO Yu-fei

2017-10-01

Full Text Available Peats are the mostly used material in making rice seedling substrate. However, mining peats could cause environmental problems. In order to reduce or replace peats in rice seedling substrate industry, this paper studied suitable way to configure rice seedling. The coal gangue was used to experiment cultivating rice. Four rice seeding experiments were carried out based on physical and chemical properties of materials attributes. The results showed:(1 Coal gangue was feasible for rice seedling; (2 The maximum adding amount of coal gangue was 80%(volume ratio though the coal gangue need to be activated; (3 In the case of no activated treatment only 38%(volume ratio of coal gangue could be added to the substrate.

THE DEVELOPMENT OF COAL-BASED TECHNOLOGIES FOR DEPARTMENT OF DEFENSE FACILITIES

Energy Technology Data Exchange (ETDEWEB)

Bruce G. Miller; Sharon Falcone Miller; Sarma V. Pisupati; Chunshan Song; Ronald S. Wasco; Ronald T. Wincek; Xiaochun Xu; Alan W. Scaroni; Richard Hogg; Subhash Chander; M. Thaddeus Ityokumbul; Mark S. Klima; Peter T. Luckie; Adam Rose; Richard L. Gordon; Jeffrey Lazo; A. Michael Schaal

2004-01-30

The third phase of a three-phase project investigating the development of coal-based technologies for US Department of Defense (DOD) facilities was completed. The objectives of the project were to: decrease DOD's dependence on foreign oil and increase its use of coal; promote public and private sector deployment of technologies for utilizing coal-based fuels in oil-designed combustion equipment; and provide a continuing environment for research and development of coal-based fuel technologies for small-scale applications at a time when market conditions in the US are not favorable for the introduction of coal-fired equipment in the commercial and industrial capacity ranges. The Phase III activities were focused on evaluating deeply-cleaned coals as fuels for industrial boilers and investigating emissions control strategies for providing ultra-low emissions when firing coal-based fuels. This was addressed by performing coal beneficiation and preparation studies, and bench- to demonstration-scale emissions reduction studies. In addition, economic studies were conducted focused on determining cost and market penetration, selection of incentives, and regional economic impacts of coal-based technologies.

Fate of the naturally occurring radioactive materials during treatment of acid mine drainage with coal fly ash and aluminium hydroxide.

Science.gov (United States)

Madzivire, Godfrey; Maleka, Peane P; Vadapalli, Viswanath R K; Gitari, Wilson M; Lindsay, Robert; Petrik, Leslie F

2014-01-15

Mining of coal is very extensive and coal is mainly used to produce electricity. Coal power stations generate huge amounts of coal fly ash of which a small amount is used in the construction industry. Mining exposes pyrite containing rocks to H2O and O2. This results in the oxidation of FeS2 to form H2SO4. The acidic water, often termed acid mine drainage (AMD), causes dissolution of potentially toxic elements such as, Fe, Al, Mn and naturally occurring radioactive materials such as U and Th from the associated bedrock. This results in an outflow of AMD with high concentrations of sulphate ions, Fe, Al, Mn and naturally occurring radioactive materials. Treatment of AMD with coal fly ash has shown that good quality water can be produced which is suitable for irrigation purposes. Most of the potentially toxic elements (Fe, Al, Mn, etc) and substantial amounts of sulphate ions are removed during treatment with coal fly ash. This research endeavours to establish the fate of the radioactive materials in mine water with coal fly ash containing radioactive materials. It was established that coal fly ash treatment method was capable of removing radioactive materials from mine water to within the target water quality range for drinking water standards. The alpha and beta radioactivity of the mine water was reduced by 88% and 75% respectively. The reduced radioactivity in the mine water was due to greater than 90% removal of U and Th radioactive materials from the mine water after treatment with coal fly ash as ThO2 and UO2. No radioisotopes were found to leach from the coal fly ash into the mine water. Copyright © 2013 Elsevier Ltd. All rights reserved.

Assessing the Impact of Removing Select Materials from Coal Mine Overburden, Central Appalachia Region, USA

Science.gov (United States)

The exposure of readily soluble components of overburden materials from surface coal mining to air and water results in mineral oxidation and carbonate mineral dissolution, thus increasing coal mine water conductivity. A conductivity benchmark of 300 µS/cm for mine water dischar...

Utilization of coal ash from fluidized-bed combustion boilers as road base material; Sekitandaki ryudoso boiler kara no sekitanbai no robanzai to shite no riyo

Energy Technology Data Exchange (ETDEWEB)

Shibata, Y. [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Kozasa, K. [Center for Coal Utilization, Japan, Tokyo (Japan); Tsuzura, K. [Naruto Salt Mfg. Co. Ltd., Tokushima (Japan); Izumi, H. [Nippon Hodo Co. Ltd., Tokyo (Japan)

1998-03-01

Coal ash from the fluidized bed boiler is evaluated for its properties as is, as solidified or granulated, and as the roadbed material. The coal ash tested in the experiment is a mixture of ash from the fluidized bed boiler bottom, ash from the cyclone separator, and ash from the bag filter. In the manufacture of solid or granulated bodies, coal ashes are kneaded in water whose amount puts the mixture near the plasticization limit, are pressed in a low-pressure press and made into solid bodies by a 15-hour curing in 60degC saturated steam, and the solid bodies are crushed into solid granules. A content release test is conducted about the release of dangerous substances, and road paving experiments are conducted to learn the workability and serviceability of the granulated material as a road paving material. A study of the experimental results discloses what is mentioned below. Coal ash containing 10-20vol% of CaO and 15vol% or less of unburnt carbon turns into a high-strength solid after curing in saturated steam whose temperature is not higher than 60degC. The granulated solid satisfies the standards that an upper subbase material is expected to satisfy. It also meets the environmental standards in a release content test for soil set forth by Environment Agency notification No.46. 8 refs., 8 figs., 4 tabs.

Seca Coal-Based Systems Program

International Nuclear Information System (INIS)

Alinger, Matthew

2008-01-01

This report summarizes the progress made during the August 1, 2006 - May 31, 2008 award period under Cooperative Agreement DE-FC26-05NT42614 for the U. S. Department of Energy/National Energy Technology Laboratory (USDOE/NETL) entitled 'SECA Coal Based Systems'. The initial overall objective of this program was to design, develop, and demonstrate multi-MW integrated gasification fuel cell (IGFC) power plants with >50% overall efficiency from coal (HHV) to AC power. The focus of the program was to develop low-cost, high performance, modular solid oxide fuel cell (SOFC) technology to support coal gas IGFC power systems. After a detailed GE internal review of the SOFC technology, the program was de-scoped at GE's request. The primary objective of this program was then focused on developing a performance degradation mitigation path for high performing, cost-effective solid oxide fuel cells (SOFCs). There were two initial major objectives in this program. These were: (1) Develop and optimize a design of a >100 MWe integrated gasification fuel cell (IGFC) power plant; (2) Resolve identified barrier issues concerning the long-term economic performance of SOFC. The program focused on designing and cost estimating the IGFC system and resolving technical and economic barrier issues relating to SOFC. In doing so, manufacturing options for SOFC cells were evaluated, options for constructing stacks based upon various cell configurations identified, and key performance characteristics were identified. Key factors affecting SOFC performance degradation for cells in contact with metallic interconnects were be studied and a fundamental understanding of associated mechanisms was developed using a fixed materials set. Experiments and modeling were carried out to identify key processes/steps affecting cell performance degradation under SOFC operating conditions. Interfacial microstructural and elemental changes were characterized, and their relationships to observed degradation

Crowding-out effect of coal industry investment in coal mining area: taking Shanxi province in China as a case.

Science.gov (United States)

Li, Li; Lei, Yalin; Xu, Qun; Wu, Sanmang; Yan, Dan; Chen, Jiabin

2017-10-01

The rapid development of coal industry in Shanxi province in China has important effects on its economic development. A large amount of money has been invested into the coal industry and other related industries during the recent years. However, research on the investment effect of Shanxi's coal industry was rare. In order to analyze the investment effect of coal industry, based on the crowding-out effect model, cointegration test, and the data available in Shanxi Statistical Yearbooks, this paper calculates the effect between coal industry investment and other 17 industry investment. The results show that the investment of coal industry produces crowding-out effect on food industry, building materials industry, and machinery industry. Increasing 1% of the coal industry investment can reduce 0.25% of the food industry investment, or 0.6% of building materials industry investment, or 0.52% of the machinery industry investment, which implies that Shanxi province should adjust coal industrial structure, promote the balance development of coal industry and other industries, so as to promote its economic growth.

Synthesis and characterization of zeolite material from coal ashes modified by surfactant

International Nuclear Information System (INIS)

Fungaro, D.A.; Borrely, S.I.

2010-01-01

Coal ash was used as starting material for zeolite synthesis by means of hydrothermal treatment. The surfactant-modified zeolite (SMZ) was prepared by adsorbing the cationic surfactant hexadecyltrimethylammonium bromide (HDTMA-Br) on the external surface of the zeolite from coal ash. The zeolite structure stability was monitored during the characterization of the materials by FTIR, XDR and SEM. The structural parameters of surfactant-modified zeolite are very close to that of corresponding non-modified zeolite which indicates that the crystalline nature of the zeolite remained intact after required chemical treatment with HDTMA-Br molecules and heating treatment for drying. The most intense peaks in the FTIR spectrum of HDTMA-Br were observed in SMZ spectrum confirming adsorption of surfactant on zeolites. (author)

Layered assembly of graphene oxide and Co-Al layered double hydroxide nanosheets as electrode materials for supercapacitors.

Science.gov (United States)

Wang, Lei; Wang, Dong; Dong, Xin Yi; Zhang, Zhi Jun; Pei, Xian Feng; Chen, Xin Jiang; Chen, Biao; Jin, Jian

2011-03-28

An innovative strategy of fabricating electrode material by layered assembling two kinds of one-atom-thick sheets, carboxylated graphene oxide (GO) and Co-Al layered double hydroxide nanosheet (Co-Al LDH-NS) for the application as a pseudocapacitor is reported. The Co-Al LDH-NS/GO composite exhibits good energy storage properties.

CdS loaded on coal based activated carbon nanofibers with enhanced photocatalytic property

Science.gov (United States)

Guo, Jixi; Guo, Mingxi; Jia, Dianzeng; Song, Xianli; Tong, Fenglian

2016-08-01

The coal based activated carbon nanofibers (CBACFs) were prepared by electrospinning a mixture of polyacrylonitrile (PAN) and acid treated coal. Cadmium sulfide (CdS) nanoparticles loaded on CBACFs were fabricated by solvothermal method. The obtained samples were characterized by FESEM, TEM, and XRD. The results reveal that the CdS nanoparticles are homogeneously dispersed on the surfaces of CBACFs. The CdS/CBACFs nanocomposites exhibited higher photoactivity for photodegradation of methyl blue (MB) under visible light irradiation than pure CdS nanoparticles. CBACFs can be used as low cost support materials for the preparation of nanocomposites with high photocatalytic activity.

Tests and studies of USSR materials at the US coal burning MHD facility UTSI-2

Energy Technology Data Exchange (ETDEWEB)

Telegin, G P; Romanov, A I; Rekov, A I; Spiridonov, E G; Barodina, T I; Vysotsky, D A

1978-10-01

In accordance with the overall program of the US--USSR cooperation in the field of MHD power generation tests of Soviet electrode materials were conducted at the coal burning MHD facility UTSI-2 of the University of Tennessee Space Institute. The main purposes of the tests are evaluation of electrode materials behavior in the channel of the MHD generator operating with combustion products of coal containing ionizing alkali seed, study of thermal and physical stability of materials in the presence of corrosive slag, study of electrophysical characteristics of electrode materials when they are subjected to the passage of current through the plasma-slag-electrode system. Tests were conducted on electrodes made of silicon carbide doped with titanium and LaCrO/sub 3/--Cr cermet. Results are reported on the phase and chemical composition and structure of these two materials, their thermophysical and electrophysical properties, and the electrode fabrication methods. The MHD facility UTSI-2, where the tests were conducted is one of few utilizing actual coal as the fuel. A description of this facility is given, and its main operating parameters and the methods used to conduct electrode tests with and without an applied current are described.

Boiler materials for ultra supercritical coal power plants

Energy Technology Data Exchange (ETDEWEB)

Purgert, Robert [Energy Industries of Ohio, Independence, OH (United States); Shingledecker, John [Electric Power Research Inst., Palo Alto, CA (United States); Pschirer, James [Alstom Power Inc., Windsor, CT (Untied States); Ganta, Reddy [Alstom Power Inc., Windsor, CT (Untied States); Weitzel, Paul [The Babcock & Wilcox Company, Baberton, OH (United States); Sarver, Jeff [The Babcock & Wilcox Company, Baberton, OH (United States); Vitalis, Brian [Riley Power Inc., Worchester, WA (United States); Gagliano, Michael [Foster Wheeler North America Corp., Hampton, NJ (United States); Stanko, Greg [Foster Wheeler North America Corp., Hampton, NJ (United States); Tortorelli, Peter [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-12-29

The U.S. Department of Energy (DOE) and the Ohio Coal Development Office (OCDO) have undertaken a project aimed at identifying, evaluating, and qualifying the materials needed for the construction of the critical components of coal-fired boilers capable of operating at much higher efficiencies than current generation of supercritical plants. This increased efficiency is expected to be achieved principally through the use of advanced ultrasupercritical (A-USC) steam conditions up to 760°C (1400°F) and 35 MPa (5000 psi). A limiting factor to achieving these higher temperatures and pressures for future A-USC plants are the materials of construction. The goal of this project is to assess/develop materials technology to build and operate an A-USC boiler capable of delivering steam with conditions up to 760°C (1400°F)/35 MPa (5000 psi). The project has successfully met this goal through a focused long-term public-private consortium partnership. The project was based on an R&D plan developed by the Electric Power Research Institute (EPRI) and an industry consortium that supplemented the recommendations of several DOE workshops on the subject of advanced materials. In view of the variety of skills and expertise required for the successful completion of the proposed work, a consortium led by the Energy Industries of Ohio (EIO) with cost-sharing participation of all the major domestic boiler manufacturers, ALSTOM Power (Alstom), Babcock and Wilcox Power Generation Group, Inc. (B&W), Foster Wheeler (FW), and Riley Power, Inc. (Riley), technical management by EPRI and research conducted by Oak Ridge National Laboratory (ORNL) has been developed. The project has clearly identified and tested materials that can withstand 760°C (1400°F) steam conditions and can also make a 700°C (1300°F) plant more economically attractive. In this project, the maximum temperature capabilities of these and other available high-temperature alloys have been assessed to provide a basis for

Maximizing efficiency in the transition to a coal-based economy

International Nuclear Information System (INIS)

Brathwaite, J.; Horst, S.; Iacobucci, J.

2010-01-01

Energy is the lynchpin of modern society. Since the early 1970s, growing dependence on foreign energy sources, oil in particular, has constrained US independence in foreign policy, and at times, inhibited economic stability and growth. Addressing oil dependence is politically and economically complex. Proposed solutions are multifaceted with various objectives such as energy efficiency and resource substitution. One solution is the partial transition from an oil- to coal-based economy. A number of facts support this solution including vast coal reserves in the US and the relative price stability of coal. However, several roadblocks exist. These include uncertain recoverable reserves and the immaturity of 'clean' coal technologies. This paper provides a first order analysis of the most efficient use of coal assuming the transition from oil to coal is desirable. Scenario analysis indicates two possible transition pathways: (1) bring the transportation sector onto the electric grid and (2) use coal-to-liquid fuels to directly power vehicles. The feasibility of each pathway is examined based on economic and environmental factors, among which are energy availability, affordability and efficiency, and environmental sustainability. Results indicate that partial transition of the transportation sector onto the electric grid offers the more viable solution for coal-based reduction of the US oil dependence.

Coal-Mining Tailings as a Pozzolanic Material in Cements Industry

Directory of Open Access Journals (Sweden)

Santiago Yagüe

2018-01-01

Full Text Available The generation of enormous volumes of mine-tailing waste is standard practice in the mining industry. Large quantities of these tailings are also sources of kaolinite-rich materials that accumulate in slag heaps, causing significant environmental degradation and visual impacts on the landscape. The consequences of coal refuse dumped in slagheaps calls for the study of eco-innovative solutions and the assessment of waste types. Moreover, the environmental benefits of reusing large amounts of contaminated waste are also evident. Hence, the objective of this investigation is to expand current knowledge of new siliceous-aluminium minerals and their pozzolanic activity. Four raw tailing samples are characterized to determine their chemical (by ICP/MS analysis, morphological (by SEM/EDX analysis, and mineralogical (by XRD analysis compositions prior to their thermal activation that transforms the inert wastes at various temperatures into materials with cementitious properties. The results of XRD analysis following activation confirmed that the kaolinite content is fully transformed into metakaolinite. The coal refuse samples presented sufficiently reliable levels of pozzolanic activity for use as additives in industrial cements.

Observer Based Fault Detection and Moisture Estimating in Coal Mill

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, Babak

2008-01-01

In this paper an observer-based method for detecting faults and estimating moisture content in the coal in coal mills is presented. Handling of faults and operation under special conditions, such as high moisture content in the coal, are of growing importance due to the increasing...... requirements to the general performance of power plants. Detection  of faults and moisture content estimation are consequently of high interest in the handling of the problems caused by faults and moisture content. The coal flow out of the mill is the obvious variable to monitor, when detecting non-intended drops in the coal...... flow out of the coal mill. However, this variable is not measurable. Another estimated variable is the moisture content, which is only "measurable" during steady-state operations of the coal mill. Instead, this paper suggests a method where these unknown variables are estimated based on a simple energy...

The coupling of coal and nuclear energy for the long-term supply of energy and raw materials

International Nuclear Information System (INIS)

Knizia, K.

1986-10-01

In view of the limited world reserves of fossil fuels and the increase in demand to be expected because of the continued growth of the world population, coal and nuclear energy will have to make an increasing contribution to the energy supply. Their contribution will range from electricity generation to the heat sector and to the raw materials market via various gases obtained from them. The further development towards this field of tasks will lead first via the gasification of coal. It will be carried out autothermally in the first stage of development. The gas produced is suitable for realising considerable improvements in efficiency as compared to coal-fired power stations of present-day design since it will permit the generation of electricity via combined gas turbine/steam turbine processes. Efforts are being made to take further the processes based on this technology by introducing a sodium circuit in addition to the coal gasification, which will make it possible to keep the plants required for coal gasification small. In later stages, this technology will also be suitable for producing a considerable improvement in the diversion of heat at high temperatures from high-temperature reactor nuclear power stations for several purposes. (author)

COAL DERIVED MATRIX PITCHES FOR CARBON-CARBON COMPOSITE MANUFACTURE/PRODUCTION OF FIBERS AND COMPOSITES FROM COAL-BASED PRECURSORS

Energy Technology Data Exchange (ETDEWEB)

Peter G. Stansberry; John W. Zondlo

2001-07-01

The Consortium for premium Carbon Products from Coal, with funding from the US Department of Energy, National Energy Technology Laboratory continue with the development of innovative technologies that will allow coal or coal-derived feedstocks to be used in the production of value-added carbon materials. In addition to supporting eleven independent projects during budget period 3, three meetings were held at two separate locations for the membership. The first was held at Nemacolin Woodlands Resort on May 15-16, 2000. This was followed by two meetings at Penn State, a tutorial on August 11, 2000 and a technical progress meeting on October 26-27.

FY 1980 Report on results of Sunshine Project. Development of coal liquefaction techniques (Development of materials for the coal liquefaction plant); 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sekitan ekika plant zairyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

A 1 T/D solvent-extraction type coal liquefaction test plant was constructed and operated to obtain the technical data for the design of, and establish the techniques for, an efficient coal liquefaction plant. The FY 1980 program includes surveys on the materials for coal liquefaction plants, covering those already developed and under development, to clarify the problematical points; drafting the test schedules; and conceptual designs of the material testing facilities. The major problems involved in the materials for coal liquefaction plants include erosion by fluidizing coal slurry, hydrogen embrittlement of the reactor materials, and corrosion by the liquefaction products (e.g., stress-corrosion cracking of austenitic steel, and corrosion by organic acids). The surveys on materials research trends suggest that USA seems to concentrate their research efforts on the reactor materials. The corrosion tests are mostly of in-plant tests, but the stress corrosion and slurry erosion tests are conducted on a laboratory scale. The conceptual designs are drawn for some testing units, e.g., the loop type material testing unit and basic testing unit for jet-spray type slurry erosion. (NEDO)

Screening of candidate corrosion resistant materials for coal combustion environments -- Volume 4. Final report, January 31, 1997

Energy Technology Data Exchange (ETDEWEB)

Boss, D.E.

1997-12-31

The development of a silicon carbide heat exchanger is a critical step in the development of the Externally-Fired Combined Cycle (EFCC) power system. SiC is the only material that provides the necessary combination of resistance to creep, thermal shock, and oxidation. While the SiC structural materials provide the thermomechanical and thermophysical properties needed for an efficient system, the mechanical properties of the SiC tubes are severely degraded through corrosion by the coal combustion products. To obtain the necessary service life of thousands of hours at temperature, a protective coating is needed that is stable with both the SiC tube and the coal combustion products, resists erosion from the particle laden gas stream, is thermal-shock resistant, adheres to SiC during repeated thermal shocks (start-up, process upsets, shut-down), and allows the EFCC system to be cost competitive. The candidate protective materials identified in a previous effort were screened for their stability to the EFCC combustion environment. Bulk samples of each of the eleven candidate materials were prepared, and exposed to coal slag for 100 hours at 1,370 C under flowing air. After exposure the samples were mounted, polished, and examined via x-ray diffraction, energy dispersive spectroscopy, and scanning electron microscopy. In general, the alumina-based materials behaved well, with comparable corrosion depths in all five samples. Magnesium chromite formed a series of reaction products with the slag, which included an alumina-rich region. These reaction products may act as a diffusion barrier to slow further reaction between the magnesium chromite and the slag and prove to be a protective coating. As for the other materials; calcium titanate failed catastrophically, the CS-50 exhibited extension microstructural and compositional changes, and zirconium titanate, barium zironate, and yttrium chromite all showed evidence of dissolution with the slag.

Seca Coal-Based Systems Program

Energy Technology Data Exchange (ETDEWEB)

Matthew Alinger

2008-05-31

This report summarizes the progress made during the August 1, 2006 - May 31, 2008 award period under Cooperative Agreement DE-FC26-05NT42614 for the U. S. Department of Energy/National Energy Technology Laboratory (USDOE/NETL) entitled 'SECA Coal Based Systems'. The initial overall objective of this program was to design, develop, and demonstrate multi-MW integrated gasification fuel cell (IGFC) power plants with >50% overall efficiency from coal (HHV) to AC power. The focus of the program was to develop low-cost, high performance, modular solid oxide fuel cell (SOFC) technology to support coal gas IGFC power systems. After a detailed GE internal review of the SOFC technology, the program was de-scoped at GE's request. The primary objective of this program was then focused on developing a performance degradation mitigation path for high performing, cost-effective solid oxide fuel cells (SOFCs). There were two initial major objectives in this program. These were: (1) Develop and optimize a design of a >100 MWe integrated gasification fuel cell (IGFC) power plant; (2) Resolve identified barrier issues concerning the long-term economic performance of SOFC. The program focused on designing and cost estimating the IGFC system and resolving technical and economic barrier issues relating to SOFC. In doing so, manufacturing options for SOFC cells were evaluated, options for constructing stacks based upon various cell configurations identified, and key performance characteristics were identified. Key factors affecting SOFC performance degradation for cells in contact with metallic interconnects were be studied and a fundamental understanding of associated mechanisms was developed using a fixed materials set. Experiments and modeling were carried out to identify key processes/steps affecting cell performance degradation under SOFC operating conditions. Interfacial microstructural and elemental changes were characterized, and their relationships to observed

Fourth annual conference on materials for coal conversion and utilization

Energy Technology Data Exchange (ETDEWEB)

1979-01-01

The fourth annual conference on materials for coal conversion and utilization was held October 9 to 11, 1979, at the National Bureau of Standards, Gaithersburg, Maryland. It was sponsored by the National Bureau of Standards, the Electric Power Research Institute, the US Department of Energy, and the Gas Research Institute. The papers have been entered individually into EDB and ERA. (LTN)

Automated mineralogical logging of coal and coal measure core

Energy Technology Data Exchange (ETDEWEB)

Stephen Fraser; Joan Esterle; Colin Ward; Ruth Henwood; Peter Mason; Jon Huntington; Phil Connor; Reneta Sliwa; Dave Coward; Lew Whitbourn [CSIRO Exploration & Mining (Australia)

2006-06-15

A mineralogical core logging system based on spectral reflectance (HyLogger{trademark}) has been used to detect and quantify mineralogies in coal and coal measure sediments. The HyLogger{trademark} system, as tested, operates in the visible-to-shortwave infrared spectral region, where iron oxides, sulphates, hydroxyl-bearing and carbonate minerals have characteristic spectral responses. Specialized software assists with mineral identification and data display. Three Phases of activity were undertaken. In Phase I, carbonates (siderite, ankerite, calcite) and clays (halloysite, dickite) were successfully detected and mapped in coal. Repeat measurements taken from one of the cores after three months demonstrated the reproducibility of the spectral approach, with some spectral differences being attributed to variations in moisture content and oxidation. Also, investigated was HyLogger{trademark} ability to create a 'brightness-profile' on coal materials, and these results were encouraging. In Phase II, geotechnically significant smectitic clays (montmorillonite) were detected and mapped in cores of clastic roof and floor materials. Such knowledge would be useful for mine planning and design purposes. In Phase III, our attempts at determining whether phosphorus-bearing minerals such as apatite could be spectrally detected were less than conclusive. A spectral index could only be created for apatite, and the relationships between the spectrally-derived apatite-index, the XRD results and the analytically-derived phosphorus measurements were ambiguous.

Natural radioactivity level in coal and ash collected from Baoji coal-fired power plant

International Nuclear Information System (INIS)

Jia Xiaodan; Lu Xinwei

2006-01-01

Specific activities of natural radionuclides 226 Ra, 232 Th and 40 K were assessed in coal (3 samples), fly ash (17 samples) and bottom ash (6 samples) collected from Baoji coal-fired power plant. This paper analyzed the characteristics of 226 Ra, 232 Th and 40 K contents in bottom ash and fly ash, and studied the concentration factors of these radionuclides in ash in relation to those in coal. The level of natural radionuclides 226 Ra, 232 Th and 40 K of coal collected from Baoji coal-fired power plant are in the range of radionuclides contents of Chinese coal. The natural radioactivity level of fly ash collected from Baoji coal-fired power plant is close to Beijing and Shanghai coal-fired power plants. The paper farther assessed the possibility of fly ash of Baoji coal-fired power plant used as building materials according to the state standard. The results show that there are 29% samples exceeding the state limit when fly ash used as building materials. So the usage of fly ash in building material should be controlled. (authors)

Radiation dose contribution from coal-slags used as structural building material

International Nuclear Information System (INIS)

Somlai, J.; Kanyar, B.; Bodnar, R.; Lendvai, Z.; Nemeth, Cs.

1996-01-01

A significant dose distribution on the population could be derived from coal slags used as isolation material. Extremely high natural activities are measured in the coal slag, derived from the region of the settlement Ajka, Hungary. In some buildings monitored, the elevated γ-doses were nearly 5-10 times higher than the world average ones. The annual average indoor radon concentrations from the slag exceeded 400 Bq/m 3 and in some cases up to 1200 Bq/m 3 . Due to the elevated exposure and the radon concentrations in the dwellings the annual dose was estimated to 8-24 mSv/y more than 5-10 times of the world average one. (author). 10 refs., 1 fig., 3 tabs

Corrosion behavior of Haynes registered 230 registered nickel-based super-alloys for integrated coal gasification combined cycle syngas plants. A plant exposure study

International Nuclear Information System (INIS)

Lee, Sungkyu; Lee, Jieun; Kang, Suk-Hwan; Lee, Seung-Jong; Yun, Yongseung; Kim, Min Jung

2015-01-01

The corrosion behavior of commercially available Haynes registered 230 registered nickel-based alloy samples was investigated by exposure to coal-gasifying integrated coal gasification combined cycle pilot plant facilities affiliated with the Institute for Advanced Engineering (2.005 MPa and 160-300 C). The morphological and microstructural analyses of the exposed samples were conducted using scanning electron microscopy and energy-dispersive X-ray spectroscopy analysis on the external surface of the recovered corrosion test samples to obtain information of the corrosion scale. These analyses based on the pre- and post-exposure corrosion test samples combined with thermodynamic Ellingham-Pourbaix stability diagrams provided preliminary insight into the mechanism of the observed corrosion behavior prevailing in the piping materials that connected the particulate removal unit and water scrubber of the integrated coal gasification combined cycle pilot plant. Uniform material wastage was observed after 46 hours of operation, and a preliminary corrosion mechanism was suggested: the observed material waste and corrosion behavior of the Haynes registered 230 registered nickel-based alloy samples cut off from the coal syngas integrated coal gasification combined cycle plant were explained by the formation of discontinuous (complex) oxide phases and subsequent chlorine-induced active oxidation under the predominantly reducing environment encountered. This contribution continues the already published studies of the Fe-Ni-Cr-Co alloy Haynes registered 556 registered .

A Comprehensive Review on the Properties of Coal Bottom Ash in Concrete as Sound Absorption Material

OpenAIRE

Ramzi Hannan Nurul Izzati Raihan; Shahidan Shahiron; Ali Noorwirdawati; Maarof Mohamad Zulkhairi

2017-01-01

The government is currently implementing policies to increase the usage of coal as fuel for electricity generation. At the same time, the dependency on gas will be reduced. In addition, coal power plants in Malaysia produce large amounts of industrial waste such as bottom ash which is collected in impoundment ponds (ash pond). However, millions of tons of coal ash (bottom ash) waste are collected in ponds near power plant stations. Since bottom ash has been classified as hazardous material th...

Balance of natural radionuclides in the brown coal based power generation and harmlessness of the residues and side product utilization

International Nuclear Information System (INIS)

Schulz, Hartmut; Kunze, Christian; Hummrich, Holger

2017-01-01

During brown coal combustion a partial enrichment of natural radionuclides occurs in different residues. Residues and side product from brown coal based power generation are used in different ways, for example filter ashes and gypsum from flue gas desulfurization facilities are used in the construction materials fabrication and slags for road construction. Detailed measurement and accounting of radionuclides in the mass throughputs in coal combustion power plants have shown that the utilized gypsum and filter ashes are harmless in radiologic aspects.

UTILIZATION OF LIGHTWEIGHT MATERIALS MADE FROM COAL GASIFICATION SLAGS

International Nuclear Information System (INIS)

None

1998-01-01

The integrated-gasification combined-cycle (IGCC) process is an emerging technology that utilizes coal for power generation and production of chemical feedstocks. However, the process generates large amounts of solid waste, consisting of vitrified ash (slag) and some unconverted carbon. In previous projects, Praxis investigated the utilization of ''as-generated'' slags for a wide variety of applications in road construction, cement and concrete production, agricultural applications, and as a landfill material. From these studies, we found that it would be extremely difficult for ''as-generated'' slag to find large-scale acceptance in the marketplace even at no cost because the materials it could replace were abundantly available at very low cost. It was further determined that the unconverted carbon, or char, in the slag is detrimental to its utilization as sand or fine aggregate. It became apparent that a more promising approach would be to develop a variety of value-added products from slag that meet specific industry requirements. This approach was made feasible by the discovery that slag undergoes expansion and forms a lightweight material when subjected to controlled heating in a kiln at temperatures between 1400 and 1700 F. These results confirmed the potential for using expanded slag as a substitute for conventional lightweight aggregates (LWA). The technology to produce lightweight and ultra-lightweight aggregates (ULWA) from slag was subsequently developed by Praxis with funding from the Electric Power Research Institute (EPRI), Illinois Clean Coal Institute (ICCI), and internal resources. The major objectives of the subject project are to demonstrate the technical and economic viability of commercial production of LWA and ULWA from slag and to test the suitability of these aggregates for various applications. The project goals are to be accomplished in two phases: Phase I, comprising the production of LWA and ULWA from slag at the large pilot scale, and

New coal-based energy systems

International Nuclear Information System (INIS)

Barnert, H.

1986-01-01

Conversion of coal into liquid fuels or into coal gas is considered and the use of high temperature nuclear reactors whose waste heat can be used for remote (district) heating mentioned. The use of high temperature reactors as energy source for coal gasification is also examined and, finally, the extraction of heat from combined coal, steel and high temperature nuclear reactors is suggested. (G.M.E.)

Experimental Study and Application of Inorganic Solidified Foam Filling Material for Coal Mines

Directory of Open Access Journals (Sweden)

Hu Wen

2017-01-01

Full Text Available Spontaneous combustion of residual coal in a gob due to air leakage poses a major risk to mining safety. Building an airtight wall is an effective measure for controlling air leakage. A new type of inorganic solidified foam-filled material was developed and its physical and chemical properties were analyzed experimentally. The compressive strength of this material increased with the amount of sulphoaluminate cement. With an increasing water–cement ratio, the initial setting time was gradually extended while the final setting time firstly shortened and then extended. The change in compressive strength had the opposite tendency. Additionally, as the foam expansion ratio increased, the solidification time tended to decrease but the compressive strength remained approximately constant. With an increase in foam production, the solidification time increased and the compressive strength decreased exponentially. The results can be used to determine the optimal material ratios of inorganic solidified foam-filled material for coal mines, and filling technology for an airtight wall was designed. A field application of the new material demonstrated that it seals crossheadings tightly, leaves no fissures, suppresses air leakage to the gob, and narrows the width of the spontaneous combustion and heat accumulation zone.

The use of coal mining wastes for manufacturing paving materials; Los esteriles del carbon como materia prima para la fabricacion de materiales para pavimentacion

Energy Technology Data Exchange (ETDEWEB)

1999-09-01

This project was aimed at proving the technical feasibility of the use of coal mining wastes in the manufacturing of paving materials; floor-tiles, flags, paving-stones, grit stones, etc.. With that aim, four types of coal mining wastes were selected out of an inventory and several tests were conducted and following the results, the most appropriate coal mining wastes, the acceptance limits and the quality control tests to be applied to the materials obtained from coal mining wastes as starting materials for the manufacturing of paving materials were established. Different laboratory test were conducted on the manufacturing of flags, floor-tiles and paving-stones. In addition, semi-industrial scale tests were carried out on the manufacturing of grit stones. Preliminary manufactory designs were elaborated for both material types. The study proved that coal mining wastes in a mixture with other raw materials can be used in the manufacturing of paving materials: floor-tiles, flags, paving-stones, grit stones. (Author)

Energy Conversion Alternatives Study (ECAS), Westinghouse phase 1. Volume 2: Materials considerations. [materials used in boilers and heat exchangers of energy conversion systems for electric power plants using coal

Science.gov (United States)

Thomas, D. E.

1976-01-01

Extensive studies are presented which were carried out on materials behavior in nine advanced energy conversion systems employing coal and coal-derived fuels. The areas of materials behavior receiving particular attention in this regard are: (1) fireside corrosion and erosion in boiler and heat exchanger materials, (2) oxidation and hot corrosion of gas turbine materials, (3) liquid metal corrosion and mass transport, (4) high temperature steam corrosion, (5) compatability of materials with coal slag and MHD seed, (6) reaction of materials with impure helium, (7) allowable stresses for boiler and heat exchanger materials, (8) environmental effects on mechanical properties, and (9) liquid metal purity control and instrumentation. Such information was then utilized in recommending materials for use in the critical components of the power systems, and at the same time to identify materials problem areas and to evaluate qualitatively the difficulty of solving those problems. Specific materials recommendations for critical components of the nine advanced systems under study are contained in summary tables.

Clean coal technology. Coal utilisation by-products

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-08-15

The need to remove the bulk of ash contained in flue gas from coal-fired power plants coupled with increasingly strict environmental regulations in the USA result in increased generation of solid materials referred to as coal utilisation by-products, or CUBs. More than 40% of CUBs were sold or reused in the USA in 2004 compared to less than 25% in 1996. A goal of 50% utilization has been established for 2010. The American Coal Ash Association (ACCA) together with the US Department of Energy's Power Plant Improvement Initiative (PPPI) and Clean Coal Power Initiative (CCPI) sponsor a number of projects that promote CUB utilization. Several are mentioned in this report. Report sections are: Executive summary; Introduction; Where do CUBs come from?; Market analysis; DOE-sponsored CUB demonstrations; Examples of best-practice utilization of CUB materials; Factors limiting the use of CUBs; and Conclusions. 14 refs., 1 fig., 5 tabs., 14 photos.

De-agglomeration and homogenisation of nanoparticles in coal tar pitch-based carbon materials

Science.gov (United States)

Gubernat, Maciej; Tomala, Janusz; Frohs, Wilhelm; Fraczek-Szczypta, Aneta; Blazewicz, Stanislaw

2016-03-01

The aim of the work was to characterise coal tar pitch (CTP) modified with selected nanoparticles as a binder precursor for the manufacture of synthetic carbon materials. Different factors influencing the preliminary preparative steps in the preparation of homogenous nanoparticle/CTP composition were studied. Graphene flakes, carbon black and nano-sized silicon carbide were used to modify CTP. Prior to introducing them into liquid CTP, nanoparticles were subjected to sonication. Various dispersants were used to prepare the suspensions, i.e. water, ethanol, dimethylformamide (DMF) and N-methylpyrrolidone (NMP).The results showed that proper dispersant selection is one of the most important factors influencing the de-agglomeration process of nanoparticles. DMF and NMP were found to be effective dispersants for the preparation of homogenous nanoparticle-containing suspensions. The presence of SiC and carbon black nanoparticles in the liquid pitch during heat treatment up to 2000 °C leads to the inhibition of crystallite growth in carbon residue.

De-agglomeration and homogenisation of nanoparticles in coal tar pitch-based carbon materials

Energy Technology Data Exchange (ETDEWEB)

Gubernat, Maciej [AGH University of Science and Technology, Faculty of Materials Science and Ceramics (Poland); Tomala, Janusz [SGL Carbon Polska S.A. (Poland); Frohs, Wilhelm [SGL CARBON GmbH (Germany); Fraczek-Szczypta, Aneta; Blazewicz, Stanislaw, E-mail: blazew@agh.edu.pl [AGH University of Science and Technology, Faculty of Materials Science and Ceramics (Poland)

2016-03-15

The aim of the work was to characterise coal tar pitch (CTP) modified with selected nanoparticles as a binder precursor for the manufacture of synthetic carbon materials. Different factors influencing the preliminary preparative steps in the preparation of homogenous nanoparticle/CTP composition were studied. Graphene flakes, carbon black and nano-sized silicon carbide were used to modify CTP. Prior to introducing them into liquid CTP, nanoparticles were subjected to sonication. Various dispersants were used to prepare the suspensions, i.e. water, ethanol, dimethylformamide (DMF) and N-methylpyrrolidone (NMP).The results showed that proper dispersant selection is one of the most important factors influencing the de-agglomeration process of nanoparticles. DMF and NMP were found to be effective dispersants for the preparation of homogenous nanoparticle-containing suspensions. The presence of SiC and carbon black nanoparticles in the liquid pitch during heat treatment up to 2000 °C leads to the inhibition of crystallite growth in carbon residue.

A Comprehensive Review on the Properties of Coal Bottom Ash in Concrete as Sound Absorption Material

Directory of Open Access Journals (Sweden)

Ramzi Hannan Nurul Izzati Raihan

2017-01-01

Full Text Available The government is currently implementing policies to increase the usage of coal as fuel for electricity generation. At the same time, the dependency on gas will be reduced. In addition, coal power plants in Malaysia produce large amounts of industrial waste such as bottom ash which is collected in impoundment ponds (ash pond. However, millions of tons of coal ash (bottom ash waste are collected in ponds near power plant stations. Since bottom ash has been classified as hazardous material that threatens the health and safety of human life, an innovative and sustainable solution has been introduced to reuse or recycle industrial waste such as coal bottom ash in concrete mixtures to create a greener and more sustainable world. Bottom ash has the potential to be used as concrete material to replace fine aggregates, coarse aggregates or both. Hence, this paper provides an overview of previous research which used bottom ash as fine aggregate replacement in conventional concrete. The workability, compressive strength, flexural strength, and sound absorption of bottom ash in concrete are reviewed.

Preparation of Fe-intercalated Graphite Based on Coal Tailings, Dimensional Structure

Directory of Open Access Journals (Sweden)

Irfan Gustian

2015-12-01

Full Text Available Intercalated graphite from coal tailings have been modified through the intercalation of iron. Coal tailings which is a byproduct of the destruction process and flakes washing results from mining coal. Intercalation of iron goal is to improve the physical properties of graphite and modifying sizes of crystal lattice structure with thermal method. Modification process begins with the carbonization of coal tailings at 500ºC and activated with phosphoric acid. Activation process has done by pyrolysis at 700ºC. The results of pyrolysis was soaked in mineral oil for 24 hours, then pyrolysis again with variations in temperature 800°C and 900ºC for 1 hour and subsequent intercalation iron at 1% and 2%. Material before activated, after activated, and the results of pyrolysis still indicates order nano: 29, 25 and 36 nm respectively. X-ray diffraction characterization results indicate that change in the structure, the sizes crystal lattice structure of the material The greater the concentration of iron was added, the resulting peak at 2θ = 33 and 35 also will be more sharply. The results of SEM showed different morphologies from each treatment.

The International Coal Statistics Data Base program maintenance guide

International Nuclear Information System (INIS)

1991-06-01

The International Coal Statistics Data Base (ICSD) is a microcomputer-based system which contains information related to international coal trade. This includes coal production, consumption, imports and exports information. The ICSD is a secondary data base, meaning that information contained therein is derived entirely from other primary sources. It uses dBase III+ and Lotus 1-2-3 to locate, report and display data. The system is used for analysis in preparing the Annual Prospects for World Coal Trade (DOE/EIA-0363) publication. The ICSD system is menu driven and also permits the user who is familiar with dBase and Lotus operations to leave the menu structure to perform independent queries. Documentation for the ICSD consists of three manuals -- the User's Guide, the Operations Manual, and the Program Maintenance Manual. This Program Maintenance Manual provides the information necessary to maintain and update the ICSD system. Two major types of program maintenance documentation are presented in this manual. The first is the source code for the dBase III+ routines and related non-dBase programs used in operating the ICSD. The second is listings of the major component database field structures. A third important consideration for dBase programming, the structure of index files, is presented in the listing of source code for the index maintenance program. 1 fig

Profit from plant experience in specifying coal conveyors

Energy Technology Data Exchange (ETDEWEB)

Rajter, L C

1985-09-01

Most coal conveyors in operation today were designed to handle raw unwashed coal and are experiencing difficulties when dealing with fine, wet coal which has been cleaned. Conveyor designers should base their designs for new systems on the worst possible materials. Design criteria are discussed in detail and recommendations made for chute liners and radii, skirt system, belt speed, transfer points, belt wipers, weather protection and access. 3 references.

Considerations on valorization of biomass origin materials in co-combustion with coal in fluidized beds

Energy Technology Data Exchange (ETDEWEB)

I. Gulyurtlu; P. Abelha; H. Lopes; A. Crujeira; I. Cabrita [DEECA-INETI, Lisbon (Portugal)

2007-07-01

Co-combustion of biomass materials with coal is currently gaining increasing importance, in order to meet the targets on greenhouse gas emissions, defined in the Kyoto protocol. Co-firing of coal with biomass materials could be the short-term solution in reducing CO{sub 2} emissions from power stations. The work undertaken studied co-firing of meat and bone meal (MBM), olive cake and straw pellets with bituminous coals from Colombia (CC) and Poland (PC), which are commonly used in European power stations. The co-combustion studies were carried out on the pilot fluidized bed installation of INETI. Gaseous pollutants and solid concentration in flue gases and ashes from different locations were monitored. Results obtained indicate that the co-feeding of biomass materials did not present any problem and ensured stable combustion conditions and high efficiency. However, for temperatures above 800{sup o}C, bed agglomeration could be observed for all biomass species studied. Most of the combustion of biomass material, contrary to that of coal, was observed to take place in the riser where the temperature was as high as 150-250{sup o}C above that of the bed. SO{sub 2} and NOx levels were found to be lower. The emissions of dioxins could be considerable with fuels with high Cl as is the case with straw. However, mixing of fuels with high S content could lead to a strong reduction in dioxin emissions. Ashes produced from biomass combustion may be considered for further reutilization or landfilling. Other options depend on their characteristics, chemical composition and leaching behaviour. This was evaluated in this study.

Multi-scale sustainability assessments for biomass-based and coal-based fuels in China.

Science.gov (United States)

Man, Yi; Xiao, Honghua; Cai, Wei; Yang, Siyu

2017-12-01

Transportation liquid fuels production is heavily depend on oil. In recent years, developing biomass based and coal based fuels are regarded as promising alternatives for non-petroleum based fuels in China. With the rapid growth of constructing and planning b biomass based and coal based fuels production projects, sustainability assessments are needed to simultaneously consider the resource, the economic, and the environmental factors. This paper performs multi-scale analyses on the biomass based and coal based fuels in China. The production cost, life cycle cost, and ecological life cycle cost (ELCC) of these synfuels are investigated to compare their pros to cons and reveal the sustainability. The results show that BTL fuels has high production cost. It lacks of economic attractiveness. However, insignificant resource cost and environmental cost lead to a substantially lower ELCC, which may indicate better ecological sustainability. CTL fuels, on the contrary, is lower in production cost and reliable for economic benefit. But its coal consumption and pollutant emissions are both serious, leading to overwhelming resource cost and environmental cost. A shifting from petroleum to CTL fuels could double the ELCC, posing great threat to the sustainability of the entire fuels industry. Copyright © 2017 Elsevier B.V. All rights reserved.

Feasibility analysis and policy recommendations for the development of the coal based SNG industry in Xinjiang

International Nuclear Information System (INIS)

Huo, Jinwei; Yang, Degang; Xia, Fuqiang; Tang, Hong; Zhang, Wenbiao

2013-01-01

Based on China's basic national energy conditions of “abundant coal and scarce gas reserve”, the development of the coal based SNG industry is considered to be an effective way to solve the conflict between the supply and demand of natural gas and an important direction in the clean use of coal. Xinjiang is rich in coal resources and is listed by the central government as one of the main bases of the coal based SNG industry. Nearly 70% of the coal based SNG projects are being conducted in Xinjiang, with the goal to take advantage of the lower coal price in Xinjiang to promote the development of the coal based SNG industry. However, the coal based SNG industry is subject to the constraints of pollution, immature technology, poor economic returns, water resources and many other factors. Therefore, the development of the coal based SNG industry should be limited to industrial demonstration. Taking into account China's energy security and environmental governance, once the technology matures, the development prospect of the coal based SNG industry is broad. - Highlights: • Booming in the coal based SNG is not oriented to market, but investment-driven. • Coal based SNG is restricted by pollution, technology, economic and water resources. • The positioning of coal based SNG industry should be industrial demonstration. • The immature technique is the biggest obstacle

Development of life cycle water-demand coefficients for coal-based power generation technologies

International Nuclear Information System (INIS)

Ali, Babkir; Kumar, Amit

2015-01-01

Highlights: • We develop water consumption and withdrawals coefficients for coal power generation. • We develop life cycle water footprints for 36 coal-based electricity generation pathways. • Different coal power generation technologies were assessed. • Sensitivity analysis of plant performance and coal transportation on water demand. - Abstract: This paper aims to develop benchmark coefficients for water consumption and water withdrawals over the full life cycle of coal-based power generation. This study considered not only all of the unit operations involved in the full electricity generation life cycle but also compared different coal-based power generating technologies. Overall this study develops the life cycle water footprint for 36 different coal-based electricity generation pathways. Power generation pathways involving new technologies of integrated gasification combined cycle (IGCC) or ultra supercritical technology with coal transportation by conventional means and using dry cooling systems have the least complete life cycle water-demand coefficients of about 1 L/kW h. Sensitivity analysis is conducted to study the impact of power plant performance and coal transportation on the water demand coefficients. The consumption coefficient over life cycle of ultra supercritical or IGCC power plants are 0.12 L/kW h higher when conventional transportation of coal is replaced by coal-log pipeline. Similarly, if the conventional transportation of coal is replaced by its transportation in the form of a slurry through a pipeline, the consumption coefficient of a subcritical power plant increases by 0.52 L/kW h

REFINERY INTEGRATION OF BY-PRODUCTS FROM COAL-DERIVED JET FUELS

Energy Technology Data Exchange (ETDEWEB)

Leslie R. Rudnick; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2005-05-18

This report summarizes the accomplishments toward project goals during the first six months of the second year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Coal samples have procured and are being assessed for cleaning prior to use in coking studies.

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Leslie R. Rudnick; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2005-11-17

This report summarizes the accomplishments toward project goals during the first six months of the second year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Evaluations to assess the quality of coal based fuel oil are reported. Coal samples have procured and are being assessed for cleaning prior to use in coking studies.

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Leslie R. Rudnick; Andre Boehman; Chunshan Song; Bruce Miller; John Andresen

2004-09-17

This report summarizes the accomplishments toward project goals during the first twelve months of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Coal samples have procured and are being assessed for cleaning prior to use in coking studies.

Enteric virus removal from water by coal-based sorbents: development of low-cost water filters

Energy Technology Data Exchange (ETDEWEB)

Chaudhuri, M.; Sattar, S.A.

1986-01-01

Using poliovirus type 1 (Sabin) and dechlorinated tap water, several coal-based sorbents were tested for their capacity to remove viruses from water. The sorbents included bituminous coal from Giridih, India, pretreated/impregnated with either alum, ferric hydroxide, lime or manganese dioxide. Filtrasorb-400, commercially available active carbon, was used as a reference. In batch tests, with input virus concentration of 2.34-2.83x10/sup 6/ PFU/1 and sorbent concentration of 10 g/l, alum pretreated coal removed about 96% of the virus when pH of the water was between 6.3 and 8.9. Virus sorption was rapid and a plateau was reached in 30 min. Compared with the active carbon, alum pretreated coal exhibited greater sorption energy and about one log higher limiting poliovirus sorption capacity. Downflow column study indicated the potential of alum pretreated coal as a filter media for removing enteric viruses from water. A previous study showed this sorbent to be capable of removing enteric bacteria as well. Water filters prepared from such low-cost material may prove useful for domestic use in rural areas of India and other developing countries. 19 refs.

Green power production by co-gasification of biomass in coal-fired oxygen-blown entrained-flow based IGCC processes

Energy Technology Data Exchange (ETDEWEB)

Van Ree, R; Korbee, R; De Smidt, R P; Jansen, D [ECN Fuels Conversion and Environment, Petten (Netherlands); Baumann, H R; Ullrich, N [Krupp Uhde, Dortmund (Germany); Haupt, G; Zimmerman, [Siemens, Erlangen (Germany)

1998-11-01

The use of coal for large scale power production meets a growing environmental concern. In spite of the fact that clean coal conversion technologies integrated with high-efficiency power production facilities, such as IGCC, are developed, the aim for sustainable development strives for a power production system based on renewable energy sources. One of the most promising renewable energy sources that can be used in the Netherlands is biomass, i.e. organic waste materials and/or energy crops. To accelerate the introduction of this material, in a technical and economically acceptable way, co-gasification with fossil fuels, in particular coal, in large scale IGCC processes is considered. In this paper the technical feasibility, economic profitability, and environmental acceptability of co-gasification of biomass in coal-fired oxygen-blown entrained-flow based IGM is discussed. Both a base-case coal-fired oxygen-blown entrained-flow based IGCC process - showing strong resemblance to the Puertollano IGCC plant in Spain - and three co-gasification concepts, viz.: (1) a concept with separate dry coal and biomass feeding systems, (2) a concept with a combined dry coal/biomass-derived pyrolysis char feeding system, and (3) a concept with parallel biomass pre-treatment/gasification and combined fuel gas clean-up/power production, were defined for further consideration. The base-case system and the co-gasification concepts as well are modelled in the flowsheet simulation package ASPEN{sup +}. Steady-state integral system calculations resulted in an overall net electrical plant efficiency for the base-case system of 50. 1 %LHV (48.3 %HHV). Replacing about 10 % of the total thermal plant input (coal) by biomass (willow) resulted in a decrease of the overall net electrical plant efficiency of 1.4 to 2.1 %-points LHV, avoided specific CO2 emissions of 40-49 g/kWh{sub e}, and total avoided CO2 emissions of about 129 to 159 kt/a, all depending on the co-gasification concept

NMR imaging: A 'chemical' microscope for coal analysis

International Nuclear Information System (INIS)

French, D.C.; Dieckman, S.L.; Gopalsami, N.; Botto, R.E.

1991-01-01

This paper presents a new three-dimensional (3-D) nuclear magnetic resonance (NMR) imaging technique for spatially mapping proton distributions in whole coals and solvent-swollen coal samples. The technique is based on a 3-D back-projection protocol for data acquisition, and a reconstruction technique based on 3-D Radon transform inversion. In principle, the 3-D methodology provides higher spatial resolution of solid materials than is possible with conventional slice-selection protocols. The applicability of 3-D NMR imaging has been demonstrated by mapping the maceral phases in Utah Blind Canyon (APCS number-sign 6) coal and the distribution of mobile phases in Utah coal swollen with deuterated and protic pyridine. 7 refs., 5 figs

Assessment of industrial energy options based on coal and nuclear systems

International Nuclear Information System (INIS)

Anderson, T.D.; Bowers, H.I.; Bryan, R.H.; Delene, J.G.; Hise, E.C.; Jones, J.E. Jr.; Klepper, O.H.; Reed, S.A.; Spiewak, I.

1975-07-01

Industry consumes about 40 percent of the total primary energy used in the United States. Natural gas and oil, the major industrial fuels, are becoming scarce and expensive; therefore, there is a critical national need to develop alternative sources of industrial energy based on the more plentiful domestic fuels--coal and nuclear. This report gives the results of a comparative assessment of nuclear- and coal-based industrial energy systems which includes technical, environmental, economic, and resource aspects of industrial energy supply. The nuclear options examined were large commercial nuclear power plants (light-water reactors or high-temperature gas-cooled reactors) and a small [approximately 300-MW(t)] special-purpose pressurized-water reactor for industrial applications. Coal-based systems selected for study were those that appear capable of meeting environmental standards, especially with respect to sulfur dioxide; these are (1) conventional firing using either low- or high-sulfur coal with stack-gas scrubbing equipment, (2) fluidized-bed combustion using high-sulfur coal, (3) low- and intermediate-Btu gas, (4) high-Btu pipeline-quality gas, (5) solvent-refined coal, (6) liquid boiler fuels, and (7) methanol from coal. Results of the study indicated that both nuclear and coal fuel can alleviate the industrial energy deficit resulting from the decline in availability of natural gas and oil. However, because of its broader range of application and relative ease of implementation, coal is expected to be the more important substitute industrial fuel over the next 15 years. In the longer term, nuclear fuels could assume a major role for supplying industrial steam. (U.S.)

Corrosion behavior of Haynes {sup registered} 230 {sup registered} nickel-based super-alloys for integrated coal gasification combined cycle syngas plants. A plant exposure study

Energy Technology Data Exchange (ETDEWEB)

Lee, Sungkyu; Lee, Jieun; Kang, Suk-Hwan; Lee, Seung-Jong; Yun, Yongseung [Institute for Advanced Engineering (IAE), Gyeonggi-do (Korea, Republic of). Plant Engineering Center; Kim, Min Jung [Sungkyunkwan Univ, Gyeonggi-do (Korea, Republic of). Advanced Materials Technology Research Center

2015-07-01

The corrosion behavior of commercially available Haynes {sup registered} 230 {sup registered} nickel-based alloy samples was investigated by exposure to coal-gasifying integrated coal gasification combined cycle pilot plant facilities affiliated with the Institute for Advanced Engineering (2.005 MPa and 160-300 C). The morphological and microstructural analyses of the exposed samples were conducted using scanning electron microscopy and energy-dispersive X-ray spectroscopy analysis on the external surface of the recovered corrosion test samples to obtain information of the corrosion scale. These analyses based on the pre- and post-exposure corrosion test samples combined with thermodynamic Ellingham-Pourbaix stability diagrams provided preliminary insight into the mechanism of the observed corrosion behavior prevailing in the piping materials that connected the particulate removal unit and water scrubber of the integrated coal gasification combined cycle pilot plant. Uniform material wastage was observed after 46 hours of operation, and a preliminary corrosion mechanism was suggested: the observed material waste and corrosion behavior of the Haynes {sup registered} 230 {sup registered} nickel-based alloy samples cut off from the coal syngas integrated coal gasification combined cycle plant were explained by the formation of discontinuous (complex) oxide phases and subsequent chlorine-induced active oxidation under the predominantly reducing environment encountered. This contribution continues the already published studies of the Fe-Ni-Cr-Co alloy Haynes {sup registered} 556 {sup registered}.

Research of Coal Resources Reserves Prediction Based on GM (1, 1) Model

Science.gov (United States)

Xiao, Jiancheng

2018-01-01

Based on the forecast of China’s coal reserves, this paper uses the GM (1, 1) gray forecasting theory to establish the gray forecasting model of China’s coal reserves based on the data of China’s coal reserves from 2002 to 2009, and obtained the trend of coal resources reserves with the current economic and social development situation, and the residual test model is established, so the prediction model is more accurate. The results show that China’s coal reserves can ensure the use of production at least 300 years of use. And the results are similar to the mainstream forecast results, and that are in line with objective reality.

Studies of materials found in products and wastes from coal-conversion processes

International Nuclear Information System (INIS)

Petersen, M.R.; Fruchter, J.S.

1979-01-01

Researchers at Pacific Northwest Laboratory (PNL) have been investigating materials from synthetic fossil-fuel processes. During this past year, solids from the Lignite Gasification Pilot Plant and samples from the Solvent Refined Coal Pilot Plant (SRC-II mode) have been analyzed for organic and inorganic constituents. Observations on these samples are summarized

Healy Clean Coal Project: Healy coal firing at TRW Cleveland Test Facility

Energy Technology Data Exchange (ETDEWEB)

Koyama, T.; Petrill, E.; Sheppard, D.

1991-08-01

A test burn of two Alaskan coals was conducted at TRW's Cleveland test facility in support of the Healy Clean Coal Project, as part of Clean Coal Technology III Program in which a new power plant will be constructed using a TRW Coal Combustion System. This system features ash slagging technology combined with NO{sub x} and SO{sub x} control. The tests, funded by the Alaska Industrial Development and Export Authority (AIDEA) and TRW, were conducted to verify that the candidate Healy station coals could be successfully fired in the TRW coal combustor, to provide data required for scale-up to the utility project size requirements, and to produce sufficient flash-calcined material (FCM) for spray dryer tests to be conducted by Joy/NIRO. The tests demonstrated that both coals are viable candidates for the project, provided the data required for scale-up, and produced the FCM material. This report describes the modifications to the test facility which were required for the test burn, the tests run, and the results of the tests.

Sorption of PAHs and PCBs to activated carbon: coal versus biomass-based quality.

Science.gov (United States)

Amstaetter, Katja; Eek, Espen; Cornelissen, Gerard

2012-04-01

The addition of activated carbon (AC) is an increasingly popular method for pollutant immobilization, and the AC material can be made of biomass or coal/fossil feedstock. The aim of the present study was to investigate whether there are differences between pollutant sorption to biomass and coal-based AC in the presence and absence of sediment. Through N(2) and CO(2) adsorption to probe surface area and pore size it was shown that the biomass-based AC had a stronger dominance of narrow pores in the size range 3.5-15Šthan the anthracite-based material. In the absence of sediment, sorption isotherms for the probe compounds pyrene and PCB-101 showed stronger sorption for the biomass-based AC (logarithmic Freundlich coefficients 8.15 for pyrene; 9.91 for PCB-101) than for the anthracite-based one (logarithmic Freundlich coefficients 7.20 and 9.70, respectively). In the presence of sediment, the opposite trend was observed, with the stronger sorption for anthracite-based AC. Thus, the presence of competing and/or pore-blocking sediment constituents reduces sorption to a larger extent for biomass-derived AC (factor of 5 for pyrene to almost 100 for PCB-101) than for anthracite-based AC (no reduction for pyrene to factor of 5 for PCB-101). This difference is tentatively attributed to the difference in pore size distribution, narrow pores being more prone to clogging, and could have implications for remediation feasibility with AC from different sources. Copyright © 2012 Elsevier Ltd. All rights reserved.

How energy technology innovation affects transition of coal resource-based economy in China

International Nuclear Information System (INIS)

Guo, Pibin; Wang, Ting; Li, Dan; Zhou, Xijun

2016-01-01

The aim of this research paper is to investigate factors and mechanisms that may facilitate the transition from coal resource-based economy to sustainability. Based on the energy technology innovation theory, factors that may influence the transition of coal resource-based economy were categorized into four types, including: innovation policy, innovation input, innovation ability, and innovation organization. Hypotheses were proposed regarding the mechanisms of these factors. Data were collected from surveys administered to 314 Chinese energy firms, and a structural equation model (SEM) was employed to test the hypotheses. Ten of fifteen hypotheses were retained based on the reliability tests, validity tests, and SEM. The results show that the four proposed factors are crucial in transforming the coal resource-based economy, and the effects become statistically significant through three intermediate variables, namely, transition of energy consumption structure, correction of resource wealth investment, and improvement of transition environment. - Highlights: •Approximately, 66% of energy relies on coal in China. •Serious environment problems have occurred in many coal-based regions. •Energy technology innovation can promote the transition of coal-based economy. •China should accelerate the development of clean energy.

Treating effluents; recovering coal, etc

Energy Technology Data Exchange (ETDEWEB)

Jones, F B; Bury, E

1920-02-18

Liquor obtained by scrubbing coal gas with sea-water or fresh water, and containing or having added to it finely-divided carbonaceous material in suspension, is subjected to a froth-flotation process to recover the carbonaceous matter and organic materials in the froth, and render the remaining liquor innocuous. Liquor obtained by scrubbing distillation gases, such as coal gas, may be used as a frothing-agent in a froth flotation process for the recovery of carbonaceous substances such as coal from materials containing them, thereby producing a froth containing the coal, etc., and also the organic materials from the liquor. In some cases the effluent may be diluted with sea-water, and, in recovering carbonaceous shales, there may be added to the liquor a small proportion of paraffin oil.

Radiation dose contribution from coal-slag from the Ajka region used as structural building material

Energy Technology Data Exchange (ETDEWEB)

Somali, J.; Kanyar, B.; Lendvai, Z.; Nemeth, C.; Bodnar, R. [Veszpremi Egyetem, Veszprem (Hungary). Radiokemia Tanszek

1997-10-01

A significant dose contribution on the population could be derived from coal slags used as material in buildings. Extremely high natural activities are measured in the coal slag from the region of Ajka, Hungary. The main conclusions based on the results of the monitoring of the gamma-dose rate and the radon concentration in the air in nearly 240 houses are as follows: (1) for individuals, such as children, spending a long time at home (19.2 h/day) the external annual dose is 1.7-4.5 mSv; (2) in the majority of houses with local slag the estimated annual average value of indoor-radon concentration was above 400 Bq/m{sup 3}, and in several cases there were buildings with values over 1200 Bq/m{sup 3}. In these cases the internal annual dose of the dwellers can be estimated between 6-20 mSv; (3) due to the elevated gamma-exposure and the radon concentration in the dwellings the total annual dose was estimated as 8-24 mSv, more than 5-10 times the world average value; and (4) some of the houses were built after the 1960s, when the use of slags from the region of Ajka as building material was already banned by the authorities. In addition to the regulations an effective radiological control should be introduced and a practice for testing the use of slag as building material.

Performance study of coal-base charcoals for removing radioiodine

International Nuclear Information System (INIS)

Huang Yuying; Wu Yanwei; Guo Liangtian; Jia Ming; Lu Xueshi; Zhang Hong

1988-01-01

In authos' laboratory sveral types of domestic coal-base charcoals are selected and impregnated and examined for their main physical and chemical performances. The results show that under the test conditions the iodine-removing efficiencies of these impregnated coal-base charcoals charcoals are not poorer than that of the impregnated fruit-shell base charcoals (such as coconut shell charcoal) and most of their physical properties can satisfy the requirements of the nuclear grade charcoals assigned in USA standards. More detailed studies will be made in the next programme

GIS Representation of Coal-Bearing Areas in Africa

Science.gov (United States)

Merrill, Matthew D.; Tewalt, Susan J.

2008-01-01

The African continent contains approximately 5 percent of the world's proven recoverable reserves of coal (World Energy Council, 2007). Energy consumption in Africa is projected to grow at an annual rate of 2.3 percent from 2004 through 2030, while average consumption in first-world nations is expected to rise at 1.4 percent annually (Energy Information Administration, 2007). Coal reserves will undoubtedly continue to be part of Africa's energy portfolio as it grows in the future. A review of academic and industrial literature indicates that 27 nations in Africa contain coal-bearing rock. South Africa accounts for 96 percent of Africa's total proven recoverable coal reserves, ranking it sixth in the world. This report is a digital compilation of information on Africa's coal-bearing geology found in the literature and is intended to be used in small scale spatial investigations in a Geographic Information System (GIS) and as a visual aid for the discussion of Africa's coal resources. Many maps of African coal resources often include points for mine locations or regional scale polygons with generalized borders depicting basin edges. Point locations are detailed but provide no information regarding extent, and generalized polygons do not have sufficient detail. In this dataset, the polygons are representative of the actual coal-bearing lithology both in location and regional extent. Existing U.S. Geological Survey (USGS) digital geology datasets provide the majority of the base geologic polygons. Polygons for the coal-bearing localities were clipped from the base geology that represented the age and extent of the coal deposit as indicated in the literature. Where the 1:5,000,000-scale geology base layer's ages conflicted with those in the publications, polygons were generated directly from the regional African coal maps (1:500,000 scale, approximately) in the published material. In these cases, coal-bearing polygons were clipped to the literature's indicated coal

Tar bases in low-temperature coal tar

Energy Technology Data Exchange (ETDEWEB)

Sugiura, S; Ueno, H; Yokoyama, H

1951-01-01

Tar bases were extracted from three fractions, that boil below 260/sup 0/ at 260/sup 0/ to 280/sup 0/, and 280/sup 0/ to 330/sup 0/, respectively, of the low-temperature tar obtained by the carbonization of Ube coal in a Koppers' vertical retort at approximately 750/sup 0/. These were divided, respectively, into three groups, acetate-forming amine, HCl salt-forming bases (I), and CHCl/sub 3/-soluble bases (II), and further fractionally distilled. From the physical and chemical properties of the fractions thus obtained, it was concluded that low-temperature coal tar contained no low boiling pyridine homologues and that, besides higher homologues of pyridine, nonaromatic, more saturated, and less basic compounds of larger atomic weight and smaller refractive index, such as derivatives of pyrrole and indole, also existed as in crude petroleum.

Density-based reflectivity in seismic exploration for coal in Alberta, Canada

Energy Technology Data Exchange (ETDEWEB)

Lawton, D.C.; Lyatsky, H.V. (University of Calgary, AB (Canada). Dept. of Geology and Geophysics)

1991-01-01

At a coal field in central Alberta, Canada, the acoustic reflectivity of shallow coal seams was found to be dominated by the density contrast between coal and host bentonitic sediments. Sonic logs and a check-shot survey showed that the compressional-wave velocity is almost constant through the coal zone and the overlying sediments, and ranges in value between 2000 m/s and 2350 m/s over different parts of the coal field. The average coal density is 1400 kg/m{sup 3}, whereas the density of the sediments is about 2200 kg/m{sup 3}. Results are illustrated using logs from a typical drillhole in the coal field. At this location, the time reflectivity sequence based on both the density and sonic logs is very similar to that obtained when the density log only is used, with a constant velocity assumed through the coal zone. At another drillhole location in the coal field, where reflection seismic data had been acquired, a synthetic seismogram generated from the density log closely matches the stacked seismic section. 6 refs., 4 figs.

Coal washery effluent treatment for material recovery and water reuse

Energy Technology Data Exchange (ETDEWEB)

Banerjee, N.N.; Chaudhuri, M.

1980-10-01

Th effluent from coal washeries consisting mainly of coal fines is normally discharged to inland surface waters and causes severe river pollution with substantial loss of good quality coking coal. The study reported in this paper was undertaken to characterize the effluents from several coal washeries and to evaluate the potential of using various coagulants and coagulant aids for clarification of the effluent with a view to recovery of the coal fines and reuse of the clarified effluent. It has been demonstrated that higher recovery of coal fines can be achieved by using coagulants like alum or ferric chloride with or without coagulant aids with an added advantage of reuse of the clarified effluent in the washery.

Brown Coal Dewatering Using Poly (Acrylamide-Co-Potassium Acrylic Based Super Absorbent Polymers

Directory of Open Access Journals (Sweden)

Sheila Devasahayam

2015-09-01

Full Text Available With the rising cost of energy and fuel oils, clean coal technologies will continue to play an important role during the transition to a clean energy future. Victorian brown coals have high oxygen and moisture contents and hence low calorific value. This paper presents an alternative non evaporative drying technology for high moisture brown coals based on osmotic dewatering. This involves contacting and mixing brown coal with anionic super absorbent polymers (SAP which are highly crossed linked synthetic co-polymers based on a cross-linked copolymer of acryl amide and potassium acrylate. The paper focuses on evaluating the water absorption potential of SAP in contact with 61% moisture Loy Yang brown coal, under varying SAP dosages for different contact times and conditions. The amount of water present in Loy Yang coal was reduced by approximately 57% during four hours of SAP contact. The extent of SAP brown coal drying is directly proportional to the SAP/coal weight ratio. It is observed that moisture content of fine brown coal can readily be reduced from about 59% to 38% in four hours at a 20% SAP/coal ratio.

Preparation of steel slag porous sound-absorbing material using coal powder as pore former.

Science.gov (United States)

Sun, Peng; Guo, Zhancheng

2015-10-01

The aim of the study was to prepare a porous sound-absorbing material using steel slag and fly ash as the main raw material, with coal powder and sodium silicate used as a pore former and binder respectively. The influence of the experimental conditions such as the ratio of fly ash, sintering temperature, sintering time, and porosity regulation on the performance of the porous sound-absorbing material was investigated. The results showed that the specimens prepared by this method had high sound absorption performance and good mechanical properties, and the noise reduction coefficient and compressive strength could reach 0.50 and 6.5MPa, respectively. The compressive strength increased when the dosage of fly ash and sintering temperature were raised. The noise reduction coefficient decreased with increasing ratio of fly ash and reducing pore former, and first increased and then decreased with the increase of sintering temperature and time. The optimum preparation conditions for the porous sound-absorbing material were a proportion of fly ash of 50% (wt.%), percentage of coal powder of 30% (wt.%), sintering temperature of 1130°C, and sintering time of 6.0hr, which were determined by analyzing the properties of the sound-absorbing material. Copyright © 2015. Published by Elsevier B.V.

Ultravitrinite coals from Chukotka

Energy Technology Data Exchange (ETDEWEB)

Lapo, A.V.; Letushova, I.A.

1979-03-01

Chemical and petrographic analysis was conducted on coals from the Anadyrya and Bukhti Ugol'noi deposits. Characteristics of the most prevalent type of vitrinite coals in both regions are presented here. Anadyrya coals belong to a transitional phase between brown coal and long flame. Ultravitrinite coals predominate. Gas coals from Bukti Ugol'noi have a higher carbon content than Anadyrya coals. They also have a higher hydrogen content and yield of initial resin. In several cases there was also a higher yield of volatile substances. Chukotka coals are characterized by a 10 percent higher initial resin yield than equally coalified Donetsk coals, other indicators were equal to those of Donetsk coals. Because of this, Chukotka coals are suitable for fuel in power plants and as raw materials in the chemical industry. (15 refs.) (In Russian)

The Impact of Coal Combustion Fly Ash Used as a Supplemental Cementitious Material on the Leaching of Constituents from Cements and Concretes

Science.gov (United States)

The objective of this report is to compare the leaching of portland cement-based materials that have been prepared with and without coal combustion fly ash to illustrate whether there is evidence that the use of fly ash in cement and concrete products may result in increased leac...

Coal option. [Shell Co

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

This paper notes the necessity of developing an international coal trade on a very large scale. The role of Shell in the coal industry is examined; the regions in which Shell companies are most active are Australia, Southern Africa, Indonesia; Europe and North America. Research is being carried out on marketing and transportation, especially via slurry pipelines; coal-oil emulsions; briquets; fluidized-bed combustion; recovery of coal from potential waste material; upgrading of low-rank coals; unconventional forms of mining; coal conversion (the Shell/Koppers high-pressure coal gasification process). Techniques for cleaning flue gas (the Shell Flue Gas Desulfurization process) are being examined.

Comparing maceral ratios from tropical peatlands with assumptions from coal studies. Do classic coal petrographic interpretation methods have to be discarded?

Energy Technology Data Exchange (ETDEWEB)

Wuest, Raphael A.J.; Hawke, Michelle I.; Marc Bustin, R. [Department of Earth and Ocean Sciences, Tropical Peat Research Group, University of British Columbia, 6339 Stores Road, V6T 1Z4 Vancouver, B.C. (Canada)

2001-12-01

Petrographic investigations of tropical peat deposits from the Tasek Bera Basin, Malaysia, show that petrographic methods can contribute valuable information about paleoecological settings of mire deposits. Comparing modern peat-forming environments and the pre-maceral composition of peat samples allows the reconstruction of paleoecological conditions, such as floral composition, fires, microbial activity, etc., and gives insight into paleodepositional environments. In the past, maceral ratios of coals have been used to interpret paleodepositional settings of coal deposits. Such a procedure assumes that coal texture and coal maceral composition are dictated solely by the depositional environment, and thus different depositional environments should be clearly discriminated based on maceral ratios. In the modern peat deposits of Tasek Bera, divergent petrographic results occur in similar depositional environments, hence, poor correlation occurs between the petrography, the degree of decomposition, and the depositional environment. Furthermore, from the time of peat deposition, peat is subject to considerable alteration. During subsequent diagenesis, preservation of structured and strongly altered material, such as inertinite, gelified material or funginite, is favoured and results in biased coal maceral compositions. Because maceral indexes in modern peat studies are of little utility in the reconstruction of paleoenvironmental settings, it follows that coal maceral indexes should not be utilized in the future to interpret paleodepositional environments of coals.

Highly Dispersed Pseudo-Homogeneous and Heterogeneous Catalysts Synthesized via Inverse Micelle Solutions for the Liquefaction of Coal

Energy Technology Data Exchange (ETDEWEB)

Hampden-Smith, M.; Kawola, J.S.; Martino, A.; Sault, A.G.; Yamanaka, S.A.

1999-01-05

The mission of this project was to use inverse micelle solutions to synthesize nanometer sized metal particles and test the particles as catalysts in the liquefaction of coal and other related reactions. The initial focus of the project was the synthesis of iron based materials in pseudo-homogeneous form. The frost three chapters discuss the synthesis, characterization, and catalyst testing in coal liquefaction and model coal liquefaction reactions of iron based pseudo-homogeneous materials. Later, we became interested in highly dispersed catalysts for coprocessing of coal and plastic waste. Bifunctional catalysts . to hydrogenate the coal and depolymerize the plastic waste are ideal. We began studying, based on our previously devised synthesis strategies, the synthesis of heterogeneous catalysts with a bifunctional nature. In chapter 4, we discuss the fundamental principles in heterogeneous catalysis synthesis with inverse micelle solutions. In chapter 5, we extend the synthesis of chapter 4 to practical systems and use the materials in catalyst testing. Finally in chapter 6, we return to iron and coal liquefaction now studied with the heterogeneous catalysts.

The influence of lisping material in pelletizing and agglomeration of fine coal pieces in laboratory conditions

International Nuclear Information System (INIS)

Vrencovski, Angele; Andreevski, Borche

1998-01-01

The work presents a part of laboratory results realized in academy of Firebug, carried on pelletizing and agglomeration of waste material, fine coal from thermal power station, using different lisping materials. Specially the influence of these materials in getting solid fuel, small briquette, formed by rolling press is analyzed. Special interest is attended to their characteristics: hardness and resistance. (Author)

Healy Clean Coal Project: Healy coal firing at TRW Cleveland Test Facility. Final report

Energy Technology Data Exchange (ETDEWEB)

Koyama, T.; Petrill, E.; Sheppard, D.

1991-08-01

A test burn of two Alaskan coals was conducted at TRW`s Cleveland test facility in support of the Healy Clean Coal Project, as part of Clean Coal Technology III Program in which a new power plant will be constructed using a TRW Coal Combustion System. This system features ash slagging technology combined with NO{sub x} and SO{sub x} control. The tests, funded by the Alaska Industrial Development and Export Authority (AIDEA) and TRW, were conducted to verify that the candidate Healy station coals could be successfully fired in the TRW coal combustor, to provide data required for scale-up to the utility project size requirements, and to produce sufficient flash-calcined material (FCM) for spray dryer tests to be conducted by Joy/NIRO. The tests demonstrated that both coals are viable candidates for the project, provided the data required for scale-up, and produced the FCM material. This report describes the modifications to the test facility which were required for the test burn, the tests run, and the results of the tests.

Refining and end use study of coal liquids

International Nuclear Information System (INIS)

1998-01-01

Two direct coal liquids were evaluated by linear programming analysis to determine their value as petroleum refinery feedstock. The first liquid, DL1, was produced from bitiuminous coal using the Hydrocarbon Technologies, Inc.(HTI) two-stage hydrogenation process in Proof of Concept Run No.1, POC-1. The second liquid, DL2,was produced from sub-bituminous coal using a three-stage HTI process in Proof of Concept Run No. 2, POC-2; the third stage being a severe hydrogenation process. A linear programming (LP) model was developed which simulates a generic 150,000 barrel per day refinery in the Midwest U.S. Data from upgrading tests conducted on the coal liquids and related petroleum fractions in the pilot plant testing phase of the Refining and End Use Study was inputed into the model. The coal liquids were compared against a generic petroleum crude feedstock. under two scenarios. In the first scenario, it was assumed that the refinery capacity and product slate/volumes were fixed. The coal liquids would be used to replace a portion of the generic crude. The LP results showed that the DL1 material had essentially the same value as the generic crude. Due to its higher quality, the DL2 material had a value of approximately 0.60 $/barrel higher than the petroleum crude. In the second scenario, it was assumed that a market opportunity exists to increase production by one-third. This requires a refinery expansion. The feedstock for this scenario could be either 100% petroleum crude or a combination of petroleum crude and the direct coal liquids. Linear programming analysis showed that the capital cost of the refinery expansion was significantly less when coal liquids are utilized. In addition, the pilot plant testing showed that both of the direct coal liquids demonstrated superior catalytic cracking and naphtha reforming yields. Depending on the coal liquid flow rate, the value of the DL1 material was 2.5-4.0 $/barrel greater than the base petroleum crude, while the DL2

Research on mechanism of and catalysts for extraction liquefaction of coal using coal-based solvents; Sekitankei yozai ni yoru sekitan no chushutsu ekika kiko to shokubai no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-07-01

Papers of Professor Yoshio Kamiya of Tokyo University are compiled into this report. The list of the papers includes (1) Synthesis of heavy fuel oils from coal; (2) Research and development of coal liquefaction; (3) Dissolution reaction of coal by hydrogen-donating aromatic solvents (I); (4) Effect of hydrogen-donor solvent on the liquefaction of coal; (5) Recent studies on the chemical structure of solvent refined coal; (6) Dissolution reaction of coal by hydrogen-donating aromatic solvents (II); (7) Future of coal as energy material; (8), (9), (10) same as (6) in the subject discussed; (11) Recent studies on coal liquefaction catalysts; (12) Environmental problems and drain treatment to accompany processes of converting fossil resources into fuels; (13) Chemistry of coal oxidation; (14) Fractionation and analysis of solvent refined coal by gel permeation chromatography; (15) Current state of research and development of coal liquefaction; (16) Properties and components of coal oils from coal liquefaction processes under development; (17) Solvent effect of coal derived aromatic compounds on the liquefaction of Akabira coal; (18) Chemistry of coal liquefaction; (19) Research and development of coal liquefaction in the U.S.; (20) Thermal treatment of coal-related aromatic ethers in tetralin solution; (21) Recent technology of utilizing heavy carbon resources; (22) Chemical properties and reactivity of coal; (23) Current state and future of development of coal liquefaction processes; and (24) Development of overseas coal liquefaction projects. (NEDO)

Waste pyritic coal as a raw material for energetic industry

Energy Technology Data Exchange (ETDEWEB)

Gasiorek, J. [Institute of Inorganic Chemistry, Poznan (Poland). Dept. of Research and Technology

1997-11-01

Results are presented of large laboratory studies on coal desulphurisation with foam flotation method improved by application of bioadsorption of Thiobacillus ferrooxidans bacteria to the modification of superficial properties of pyrite particulates from hydrophobic to hydrophillic ones. Results of coal desulfurization with and without bioadsorption have been compared. Bioadsorption improved pyritic sulfur removal by 30% (for coal from `Sierza mine`, coal size 0.3 to 0.102 mm, S pyritic content 1.69%) after 6-week adaptation of bacteria and 30 min of bioadsorption. Bacteria concentration in 5% water suspension of coal reached 22 {mu}g of biomass cm{sup -3}. 12 refs., 4 figs., 1 tab.

Prospects For Coal And Clean Coal Technologies In Kazakhstan

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-12-15

The coal sector in Kazakhstan is said to have enough reserves to last over 100 years, but the forecasted reserves are expected to last several hundreds of years. This makes investing in the fuel and energy sector of the country an attractive option for many international and private organisations. The proven on-shore reserves will ensure extraction for over 30 years for oil and 75 years for gas. The future development of the domestic oil sector depends mainly on developing the Kazakh sector of the Caspian Sea. The coal sector, while not a top priority for the Kazakh government, puts the country among the world's top ten coal-rich countries. Kazakhstan contains Central Asia's largest recoverable coal reserves. In future, the development of the raw materials base will be achieved through enriching and improving the quality of the coal and the deep processing of coal to obtain fluid fuel and synthetic substances. Developing shale is also topical. The high concentration of methane in coal layers makes it possible to extract it and utilise it on a large scale. However, today the country's energy sector, which was largely established in the Soviet times, has reached its potential. Kazakhstan has about 18 GW of installed electricity capacity, of which about 80% is coal fired, most of it built before 1990. Being alert to the impending problems, the government is planning to undertake large-scale modernisation of the existing facilities and construct new ones during 2015-30. The project to modernise the national electricity grid aims to upgrade the power substations to ensure energy efficiency and security of operation. The project will result in installation of modern high-voltage equipment, automation and relay protection facilities, a dispatch control system, monitoring and data processing and energy management systems, automated electricity metering system, as well as a digital corporate telecommunication network.

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline E. Burgess Clifford; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2006-05-17

This report summarizes the accomplishments toward project goals during the first six months of the third year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts, acquisition and installation of a research gasoline engine, and modification of diesel engines for use in evaluating diesel produced in the project. Characterization of the gasoline fuel indicates a dominance of single ring alkylcycloalkanes that have a low octane rating; however, blends containing these compounds do not have a negative effect upon gasoline when blended in refinery gasoline streams. Characterization of the diesel fuel indicates a dominance of 3-ring aromatics that have a low cetane value; however, these compounds do not have a negative effect upon diesel when blended in refinery diesel streams. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Combustion and characterization of fuel oil indicates that the fuel is somewhere in between a No. 4 and a No. 6 fuel oil. Emission testing indicates the fuel burns similarly to these two fuels, but trace metals for the coal-based material are different than petroleum-based fuel oils. Co-coking studies using cleaned coal are highly reproducible in the pilot-scale delayed coker. Evaluation of the coke by Alcoa, Inc. indicated that while the coke produced is of very good quality, the metals content of the carbon is still high in iron and silica. Coke is being evaluated for other possible uses

Determination of moisture in coal, in the case of discontinuous transport, using condensers

Energy Technology Data Exchange (ETDEWEB)

Prieto-Fernandez, Ismael; Luengo-Garcia, Juan-Carlos; Alonso, Manuela [Area Maquinas y Motores Termicos, Universidad de Oviedo, Campus Universitario, 33203 , Asturias Gijon (Spain)

2002-02-20

The need for a rapid method of determining the technological characteristics of coal has been increasing in the last decades. The coal industry demands methods of coal analysis on a rapid and reasonably accurate basis. In this report, a non-conventional system for moisture analysis of thermal coal, based on capacitance techniques, is proposed. A device for non-continuous analysis based on this technique is designed and developed. Such device simulates a cylindrical condenser, in which coal acts as the dielectric material. The device is used to measure moisture content in coals. The results from the statistical analyses and conclusions are presented. Also, on-site potential use of capacitance techniques is shown.

The use of coal mining wastes for manufacturing paving materials; Los Esteriles del Carbon como Materia Prima para la Fabricacion de Materiales para Pavimentacion

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

This project was aimed at proving the technical feasibility of the use of coal mining wastes in the manufacturing of paving materials: floor-tiles, flags, paving-stones, grit stones, etc. The study proved that coal mining wastes in a mixture with other raw materials can be used in the manufacturing of paving materials: floor-tiles, paving-stones, grit stones.

Techno-economic analysis and comparison of coal based olefins processes

International Nuclear Information System (INIS)

Xiang, Dong; Yang, Siyu; Qian, Yu

2016-01-01

Highlights: • The coal based Fischer–Tropsch-to-olefins (CFTO) process is proposed and analyzed. • The CFTO suffers from lower energy efficiency and serious CO 2 emissions. • Approaches for improving techno-economic performance of the CFTO are obtained. - Abstract: Traditional olefins production is heavily dependent on oil. In the background of the scarcity of oil and richness of coal in China, olefins production from coal has been attracting more attention of the chemical process industry. The first coal based methanol-to-olefins (CMTO) plant has been commercialized in China. For shorter process route and lower capital cost, Fischer–Fropsch has been put forward in the last few years. The coal based Fischer–Tropsch-to-olefins (CFTO) process is designed in this paper and then its techno-economic and environmental performance was detailed studied in this paper, in comparison with the CMTO. Results show that at the present olefins selectivity, the CFTO suffers from relative lower energy efficiency and higher CO 2 emissions. In economic aspect, the capital investment and product cost of the CFTO are roughly equivalent to that of the CMTO. Although the conversion route of the CFTO is shorter, its techno-economic performance is still inferior to that of the CMTO. It is also found that increase of olefins selectivity by cracking oil or decrease of CO 2 selectivity by improving catalyst could significantly improve the performance of the CFTO.

Estimation of Moisture Content in Coal in Coal Mills

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, B.

the moisture content of the coal is proposed based on a simple dynamic energy model of a coal mill, which pulverizes and dries the coal before it is burned in the boiler. An optimal unknown input observer is designed to estimate the moisture content based on an energy balance model. The designed moisture...

Estimation of Moisture Content in Coal in Coal Mills

DEFF Research Database (Denmark)

Odgaard, Peter Fogh; Mataji, Babak

2006-01-01

the moisture content of the coal is proposed based on a simple dynamic energy model of a coal mill, which pulverizes and dries the coal before it is burned in the boiler. An optimal unknown input observer is designed to estimate the moisture content based on an energy balance model. The designed moisture...

Facing coal : changing conceptions of South African coal-based pollution, with special reference to the Witbank coalfield, 1906-1978

NARCIS (Netherlands)

Singer, M.

2011-01-01

Facing coal provides an environmental history of changing ideas around South African coal-based pollution, focusing on Witbank, where the scars of mining are etched deep into the land. The essence of this book is its link between local and global repercussions of past and present reliance on fossil

Adsorption of SO2 on bituminous coal char and activated carbon fiber prepared from phenol formaldehyde

Science.gov (United States)

DeBarr, Joseph A.; Lizzio, Anthony A.; Daley, Michael A.

1996-01-01

Carbon-based materials are used commercially to remove SO2 from coal combustion flue gases. Historically, these materials have consisted of granular activated carbons prepared from lignite or bituminous coal. Recent studies have reported that activated carbon fibers (ACFs) may have potential in this application due to their relatively high SO2 adsorption capacity. In this paper, a comparison of SO2 adsorption for both coal-based carbons and ACFs is presented, as well as ideas on carbon properties that may influence SO2 adsorption

Fireside corrosion of nickel base alloys in future 700 C coal fired power plants; Rauchgasseitige Korrosion von Nickelbasislegierungen fuer zukuenftige 700 C-Dampfkraftwerke

Energy Technology Data Exchange (ETDEWEB)

Luettschwager, Frank

2011-09-27

Coal is still the most important energy source in Germany. In 2009 it produced 42.9 % of the overall German electrical power. Coal is available world-wide in large quantities and can be delivered economically. One of the possible ways to reduce CO{sub 2} pollution is the increase of efficiency of coal fired power plants, which requires steam conditions of up to 700 C - 730 C and 350 bar. Because many German power units will reach the end of their technical lifespan in a few years or the following decade, one will have the possibility to build up modern types of power plants with increased efficiency of more than 50 %. Some international standards (European Pressure Equipment Directive or ASME Boiler and Pressure Vessel Code) require 100 000 hour creep rupture strength of 100 MPa at 750 C. Therefore, nickel base alloys are in the focus of material qualification processes. Nickel base alloys are well investigated due to their hot corrosion behaviour. It is known that sodium sulphate may generate hot corrosion on those alloys at temperatures above its melting point of 884 C. On nickel base alloys an eutectic mixture of nickel sulphate and sodium sulphate with a melting point of 671 C can be generated, which leads to accelerated corrosion. This work examines, whether the high amount of sulphur and alkali metals will induce hot corrosion at the estimated working temperature on devices manufactured from nickel base alloy. Two synthetic coal ash deposits, according to the chemical composition of hard coal and lignite, and typical flue gases with and without sulphur dioxide were blended of pure agents. The reactions of the deposits with heater tubes' materials and synthetic flue gases are examined in the temperature range from 650 C to 800 C and different time ranges up to 2000 hours. The corroded specimen are examined with SEM/EDX to identify relevant corrosion products and determine the corrosivity of deposited compounds. Deposits increase the corrosion rate of

Cost and performance of coal-based energy in Brazil

International Nuclear Information System (INIS)

Temchin, J.; DeLallo, M.R.

1998-01-01

As part of the US Department of Energy's (DOE) efforts to establish the strategic benefits of Clean Coal Technologies (CCT), there is a need to evaluate the specific market potential where coal is a viable option. One such market is Brazil, where significant growth in economic development requires innovative and reliable technologies to support the use of domestic coal. While coal is Brazil's most abundant and economic fossil energy resource, it is presently under utilized in the production of electrical power. This report presents conceptual design for pulverized coal (PC) and circulating fluidized-bed combustion (CFBC) options with resulting capital, operating and financial parameters based on Brazil application conditions. Recent PC and CFBC plant capital costs have dropped with competition in the generation market and have established a competitive position in power generation. Key issues addressed in this study include: Application of market based design approach for FBC and PC, which is competitive within the current domestic, and international power generation markets. Design, fabrication, purchase, and construction methods which reduce capital investment while maintaining equipment quality and plant availability. Impact on coast and performance from application of Brazilian coals, foreign trade and tax policies, construction logistics, and labor requirements. Nominal production values of 200 MWe and 400 MWe were selected for the CFBC power plant and 400 MWe for the PC. The 400 MWe size was chosen to be consistent with the two largest Brazilian PC units. Fluidized bed technology, with limited experience in single units over 200 MW, would consist of two 200 MWe circulating fluidized bed boilers supplying steam to one steam turbine for the 400 MWe capacity. A 200 MWe capacity unit was also developed for CFBC option to support opportunities in re-powering and where specific site or other infrastructure constraints limit production

Raw-materials mixtures from waste of the coal industry for production of ceramic materials

Energy Technology Data Exchange (ETDEWEB)

Galpern, E I [Scientific-Manufacturing Enterprise ` ` Ceramics` ` , Donetsk (Ukraine); Pashchenko, L V [Inst. of Physical, Organic and Coal Chemistry of NASU, Donetsk (Ukraine)

1998-09-01

The liquidation of waste dumps on the surface of mining enterprises and realization of measures by environment protection of air and aquatic basins are connected to the complex processing of mining mass. The main directions of utilization of mining rocks and coal wastes realized in Ukraine industry are: - filling of mines worked-out area by grouting solutions; - ceramic brick, porous filling materials and binding materials production; - road-making, construction of hydrostructures and industrial objects; - output of concrete items predominantly for using in mining conditions. The peculiarity of wastes using in above-mentioned fields is the possibility of their mass application in quantities commensurable with valumes of their yields. The experience of enterprises work which process mining rocks into building materials by burning method (ceramic brick, porous aggregates of concretes as aggloporite, expanded clay aggregate) has shown that unconstant and, as the rule, exceeding norms content of carbon and sulphur in the rock results to deterioration of products quality and technological factors of production. Unstability of carbon content in raw material makes the burning process hardly operated. Obtained products having residual carbon in the view of coke residue are often characterized by lower physical-mechanical characteristics. (orig./SR)

Alkali-assisted coal extraction with polar aprotic solvents

Energy Technology Data Exchange (ETDEWEB)

Makgato, M.H.; Moitsheki, L.J.; Shoko, L.; Kgobane, B.L.; Morgan, D.L.; Focke, W.W. [SARChI Chair in Carbon Technology and Materials, Institute of Applied Materials, University of Pretoria, Pretoria 0002 (South Africa)

2009-04-15

Coal extraction experiments were conducted using a coal, containing ca. 10% ash, from the Tshikondeni mine in South Africa. This coal dissolves only to a limited extent in pure polar aprotic solvents such as dimethylformamide (DMF) and N-methyl-2-pyrrolidinone (NMP). However, the addition of a strong base, e.g. sodium hydroxide (NaOH) or sodium tert-butoxide increased the degree of coal dissolution in these organic solvents. Depending on the extraction conditions, carbon extraction efficiencies of up to 90% were obtained. Carbon precursor material was recovered from the solution as a gel by precipitation with water. Ash content was reduced from 10% in the coal to less than 1.6% in the coal extracts. Sodium sulfide (Na{sub 2}S) addition further reduced ash content and aided the recovery of carbon precursors that led to graphitizable cokes but the degree of extraction was significantly reduced. (author)

W(h)ither the coal industry? The long-term view

International Nuclear Information System (INIS)

Schobert, H.H.; Rusinko, F. Jr.; Mathews, J.P.

1998-01-01

Global warming--real or imaginary, friend or foe, carbon dioxide emissions a threat to the planet, benign, or good for agriculture--while the debate rages on, the debaters occasionally seem to pause long enough to agree on one point: coal is the bad guy. There is little doubt that coal combustion must continue as a major contributor to the energy economy for the near to mid-term future. It is likely, though, those environmental pressures on conventional processes for coal utilization will only intensify. This factor alone makes questionable the long-term future. Environmental issues also severely impact the metallurgical coke industry. The traditional coal industry and coal markets of the 20th century are under increasingly intense assault. But why waste coal by burning it? Steady progress is being made in two directions for using coal as a valuable hydrocarbon resource. On the one hand, continuous improvements in computer-based structural modeling, which now include the ability to calculate not only a molecular structure that is consistent with chemical facts, but also some of the physical properties and even the incorporation of water. The increasing reasonableness of such structures places one on the verge of being able to do rational organic chemistry on coals, that is, deliberately to select coals as starting materials for certain desired chemical transformations that will produce high-value chemical products in good yields. This opens a route to chemicals from coal that does not rely on by-product coal tars as the feedstock. On the other hand, excellent opportunities also exist for coals as precursors to high-value carbon materials. Anthracites in particular represent an under-exploited, and as yet poorly explored, opportunity for conversion to graphitic materials. Taking coal in both directions high-value chemicals and premium carbon products represent profitable opportunities for innovation, leadership, and new directions for the coal industry in the 21st

Mechanism of plasma-arc formation of fullerenes from coal and related materials

Energy Technology Data Exchange (ETDEWEB)

Pang, L S.K.; Wilson, M A; Quezada, R A [CSIRO Petroleum, North Ryde (Australia); and others

1996-12-31

When an arc is struck across graphite or coal electrodes in a helium atmosphere several products are formed including soot containing fullerenes. The mechanism by which fullerenes and nanotubes are formed is not understood. At arc temperatures exceeding 3000{degrees}C, highly ordered fullerenes might be expected to be less stable than graphite, and hence fullerene production is believed to proceed in cooler regions at the edge of the arc. There is irrefutable evidence that [C{sub 60}]-fullerene grows in a plasma from atomic carbon vapour or equivalent. When {sup 13}C-labelled carbon powder is packed into the anode, the fullerenes as produced contain a statistical distribution of {sup 13}C atoms. This implies that graphite has split into small units, predominantly C{sub 1} or C{sub 2} in the plasma and these units are involved in fullerene formation. When coal or other organic materials are used in the anode, weaker bonds are present, which may break preferentially. As a result, larger fragments, other than C{sub 1} and C{sub 2} units can exist in the plasma. This paper demonstrates the existence of such larger fragments when various coals are used and this implies that fullerenes can be formed from larger units than C{sub 1} and C{sub 2}. The distribution of polycyclic hydrocarbons formed depends very much on the structure of the coal used for the arcing experiments. The distribution of the natural abundance of {sup 13}C/{sup 12}C ratios in the fullerene products further supports this evidence.

Novel pre-treatment of zeolite materials for the removal of sodium ions: potential materials for coal seam gas co-produced wastewater.

Science.gov (United States)

Santiago, Oscar; Walsh, Kerry; Kele, Ben; Gardner, Edward; Chapman, James

2016-01-01

Coal seam gas (CSG) is the extraction of methane gas that is desorbed from the coal seam and brought to the surface using a dewatering and depressurisation process within the saturated coalbed. The extracted water is often referred to as co-produced CSG water. In this study, co-produced water from the coal seam of the Bowen Basin (QLD, Australia) was characterised by high concentration levels of Na(+) (1156 mg/L), low concentrations of Ca(2+) (28.3 mg/L) and Mg(2+) (5.6 mg/L), high levels of salinity, which are expected to cause various environmental problems if released to land or waters. The potential treatment of co-produced water using locally sourced natural ion exchange (zeolite) material was assessed. The zeolite material was characterized for elemental composition and crystal structure. Natural, untreated zeolite demonstrated a capacity to adsorb Na(+) ions of 16.16 mEq/100 g, while a treated zeolite using NH4 (+) using a 1.0 M ammonium acetate (NH4C2H3O2) solution demonstrated an improved 136 % Na(+) capacity value of 38.28 mEq/100 g after 720 min of adsorption time. The theoretical exchange capacity of the natural zeolite was found to be 154 mEq/100 g. Reaction kinetics and diffusion models were used to determine the kinetic and diffusion parameters. Treated zeolite using a NH4 (+) pre-treatment represents an effective treatment to reduce Na(+) concentration in coal seam gas co-produced waters, supported by the measured and modelled kinetic rates and capacity.

PROBLEMS AND METHODOLOGY OF THE PETROLOGIC ANALYSIS OF COAL FACIES.

Science.gov (United States)

Chao, Edward C.T.

1983-01-01

This condensed synthesis gives a broad outline of the methodology of coal facies analysis, procedures for constructing sedimentation and geochemical formation curves, and micro- and macrostratigraphic analysis. The hypothetical coal bed profile has a 3-fold cycle of material characteristics. Based on studies of other similar profiles of the same coal bed, and on field studies of the sedimentary rock types and their facies interpretation, one can assume that the 3-fold subdivision is of regional significance.

Coal liquefaction by base-catalyzed hydrolysis with CO.sub.2 capture

Science.gov (United States)

Xiao, Xin

2014-03-18

The one-step hydrolysis of diverse biomaterials including coal, cellulose materials such as lumber and forestry waste, non-food crop waste, lignin, vegetable oils, animal fats and other source materials used for biofuels under mild processing conditions which results in the formation of a liquid fuel product along with the recovery of a high purity CO.sub.2 product is provided.

Response of plant species to coal-mine soil materials

Energy Technology Data Exchange (ETDEWEB)

Day, A.D.; Tucker, T.C.; Thames, J.L.

1983-03-01

The two-year Black Mesa Coal Mine Research Study on the area near Kayenta, Arizona investigating the growth and establishment of seven plant species in unmined soil and coal-mined soils found that plant species grew better in unmined soil and that irrigation is essential during seedling establishment for the effective stabilization of coal-mined soils in a semi-arid environment. Differences among the species included variations in germination, response to irrigation, seedling establishment, and stem growth. 12 references, 2 figures, 2 tables.

The fate of injectant coal in blast furnaces: The origin of extractable materials of high molecular mass in blast furnace carryover dusts

Energy Technology Data Exchange (ETDEWEB)

Dong, S.N.; Wu, L.; Paterson, N.; Herod, A.A.; Dugwell, D.R.; Kandiyoti, R. [University of London Imperial College of Science & Technology, London (United Kingdom). Dept. of Chemical Engineering

2005-07-01

The aim of the work was to investigate the fate of injectant coal in blast furnaces and the origin of extractable materials in blast furnace carryover dusts. Two sets of samples including injectant coal and the corresponding carryover dusts from a full sized blast furnace and a pilot scale rig have been examined. The samples were extracted using 1-methyl-2-pyrrolidinone (NMP) solvent and the extracts studied by size exclusion chromatography (SEC). The blast furnace carryover dust extracts contained high molecular weight carbonaceous material, of apparent mass corresponding to 10{sup 7}-10{sup 8} u, by polystyrene calibration. In contrast, the feed coke and char prepared in a wire mesh reactor under high temperature conditions did not give any extractable material. Meanwhile, controlled combustion experiments in a high-pressure wire mesh reactor suggest that the extent of combustion of injectant coal in the blast furnace tuyeres and raceways is limited by time of exposure and very low oxygen concentration. It is thus likely that the extractable, soot-like material in the blast furnace dust originated in tars is released by the injectant coal. Our results suggest that the unburned tars were thermally altered during the upward path within the furnace, giving rise to the formation of heavy molecular weight (soot-like) materials.

Role of non-ferrous coal minerals and by-product metallic wastes in coal liquefaction. Technical progress report, March 1, 1981-May 31, 1981

Energy Technology Data Exchange (ETDEWEB)

Garg, D.; Givens, E.N.; Schweighardt, F.K.; Curtis, C.W.; Guin, J.A.; Huang, W.J.; Shridharani, K.

1981-06-01

This report covers results from both tubing-bomb experiments and continuous PDU runs. The following materials were evaluated in the PDU on Elkhorn No. 2 coal from Floyd County, Kentucky: Molybdic oxides; iron oxide; pyrite; pyrite/iron oxide mixture, and iron sulfate impregnation. A base case liquefaction run was also made for direct comparison. All of the above materials were examined at both 825 and 850/sup 0/F. Tubing-bomb experiments are reported on pyrite, red mud, sodium sulfide and organic compounds of cobalt, nickel, molybdenum, zinc, chromium and lead. Significant conclusions were drawn on the catalysis by different materials. Especially significant was the higher level of activity resulting from impregnation versus particle incorporation of the catalyst in the system. Impregnation of coal decreased the hydrocarbon gases yield and increased oil yield. Hydrogen consumption was significantly reduced by impregnation. Addition of molybdic oxide containing 90% MoO/sub 3/ and 10% silica to coal liquefaction reaction mixture had the following effect: coal conversion increased, oil yield increased by more than a factor of two at both temperatures, hydrogen consumption increased, solvent/oil fraction showed substantial increase in hydrogen content, and molybdenum in the resulting liquefaction residue was apparently transformed into an amorphous material. A more thorough evaluation of completely sulfided molybdenum will be made to see if its activity increases. In the tubing-bomb experiments organic compound of molybdenum showed the highest activity for coal conversion and oil production. Significant synergism was noted between red mud and sodium sulfide in the coal liquefaction reaction.

Characterization and supply of coal based fuels. Volume 1, Final report and appendix A (Topical report)

Energy Technology Data Exchange (ETDEWEB)

1992-06-01

Studies and data applicable for fuel markets and coal resource assessments were reviewed and evaluated to provide both guidelines and specifications for premium quality coal-based fuels. The fuels supplied under this contract were provided for testing of advanced combustors being developed under Pittsburgh Energy Technology Center (PETC) sponsorship for use in the residential, commercial and light industrial (RCLI) market sectors. The requirements of the combustor development contractors were surveyed and periodically updated to satisfy the evolving needs based on design and test experience. Available coals were screened and candidate coals were selected for further detailed characterization and preparation for delivery. A team of participants was assembled to provide fuels in both coal-water fuel (CWF) and dry ultrafine coal (DUC) forms. Information about major US coal fields was correlated with market needs analysis. Coal fields with major reserves of low sulfur coal that could be potentially amenable to premium coal-based fuels specifications were identified. The fuels requirements were focused in terms of market, equipment and resource constraints. With this basis, the coals selected for developmental testing satisfy the most stringent fuel requirements and utilize available current deep-cleaning capabilities.

Utilizing coal remaining resources and post-mining land use planning based on GIS-based optimization method : study case at PT Adaro coal mine in South Kalimantan

Directory of Open Access Journals (Sweden)

Mohamad Anis

2017-06-01

Full Text Available Coal mining activities may cause a series of environmental and socio-economic issues in communities around the mining area. Mining can become an obstacle to environmental sustainability and a major hidden danger to the security of the local ecology. Therefore, the coal mining industry should follow some specific principles and factors in achieving sustainable development. These factors include geological conditions, land use, mining technology, environmental sustainability policies and government regulations, socio-economic factors, as well as sustainability optimization for post-mining land use. Resources of the remains of the coal which is defined as the last remaining condition of the resources and reserves of coal when the coal companies have already completed the life of the mine or the expiration of the licensing contract (in accordance with government permission. This research uses approch of knowledge-driven GIS based methods mainly Analytical Hierarchy Process (AHP and Fuzzy logic for utilizing coal remaining resources and post-mining land use planning. The mining area selected for this study belongs to a PKP2B (Work Agreement for Coal Mining company named Adaro Indonesia (PT Adaro. The result shows that geologically the existing formation is dominated by Coal Bearing Formation (Warukin Formation which allows the presence of remains coal resource potential after the lifetime of mine, and the suitability of rubber plantation for the optimization of land use in all mining sites and also in some disposal places in conservation areas and protected forests.

Development of advanced corrosion resistant materials for molten coal ash; Yoyu sekitanbai ni taisuru kotaishokusei zairyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

For development of materials for heat exchangers under severe corrosion environment due to ultra-high temperature coal combustion gas, basic data were surveyed. On the study in fiscal 1996, the corrosion resistance of one kind of commercially available material and 2 kinds of created materials was studied by coal slag coating test. The commercially available material was subjected to high- temperature corrosion tests of 1500 and 1550degC for a long time. The result showed that SiC is most excellent in the above temperature range. On new materials, 7 kinds of Cr2O3 system ceramics such as Cr2O3-Al2O3 system and Cr2O3- MgO system were selected considering high-temperature corrosion resistance, and the optimum composition and fabrication process of the new materials were studied. High- temperature corrosion tests, and measurement of thermal conductivity and thermal expansion were carried out for every specimen. The result suggested that some materials of Cr2O3- Al2O3 system are promising. 23 refs., 76 figs., 23 tabs.

Correlation between the coal quality from 'Suvodol' and briquetting processes for coals, peat and other combustible materials (coal deposit in Macedonia)

International Nuclear Information System (INIS)

Damjanovski, Dragan; Popovski, Dushko; Mitrevski, Pece

1997-01-01

In this paper the regression equations for the characteristics of Suvodol coal and the technological parameters of obtained briquets are given. It is shown that correlations between the coal characteristics are linear, while correlations between briquetting parameters are nonlinear

Processing Uranium-Bearing Materials Containing Coal and Loam

Energy Technology Data Exchange (ETDEWEB)

Civin, V; Prochazka, J [Research and Development Laboratory No. 3 of the Uranium Industry, Prague, Czechoslovakia (Czech Republic)

1967-06-15

Among the ores which are classified as low-grade in the CSSR are mixtures of coal and bentonitic loam of tertiary origin, containing approximately 0.1% U and with a moisture content at times well above 20-30%. The uranium is held mainly by the carbonaceous component. Conventional processing of these materials presents various difficulties which are not easily overcome. During leaching the pulp thickens and frequently becomes pasty, due to the presence of montmorillonites. Further complications arise from the high sorption capacity of the materials (again primarily due to montmorillonites) and poor sedimentation of the viscous pulps. In addition, the materials are highly refractory to the leaching agents. The paper presents experience gained in solving the problems of processing these ores. The following basic routes were explored: (1) separation of the carbonaceous and loamy components: The organic component appears to be the main activity carrier. Processing the concentrated material upon separation of the inactive or less active loam may not only remove the thixotropic behaviour but also substantially reduce the cost of the ore treatment; (2) 'liquifying' the pulps or preventing the thickening of the pulp by addition of suitable agents; (3) joint acid or carbonate processing of the materials in question with current ore types; (4) removal or suppression of thixotropic behaviour by thermal pretreatment of the material; and (5) application of the 'acid cure' method. The first method appears to be the most effective, but it presents considerable difficulties due to the extreme dispersion of the carbonaceous phase and further research is being carried out. Methods 2 and 3 proved to be unacceptable. Method 4, which includes roasting at 300-400{sup o}C, is now being operated on an industrial scale. The final method has also shown definite advantages for particular deposits of high montmorillonite content material. (author)

GEOTECHNICAL/GEOCHEMICAL CHARACTERIZATION OF ADVANCED COAL PROCESS WASTE STREAMS

Energy Technology Data Exchange (ETDEWEB)

Edwin S. Olson; Charles J. Moretti

1999-11-01

Thirteen solid wastes, six coals and one unreacted sorbent produced from seven advanced coal utilization processes were characterized for task three of this project. The advanced processes from which samples were obtained included a gas-reburning sorbent injection process, a pressurized fluidized-bed coal combustion process, a coal-reburning process, a SO{sub x}, NO{sub x}, RO{sub x}, BOX process, an advanced flue desulfurization process, and an advanced coal cleaning process. The waste samples ranged from coarse materials, such as bottom ashes and spent bed materials, to fine materials such as fly ashes and cyclone ashes. Based on the results of the waste characterizations, an analysis of appropriate waste management practices for the advanced process wastes was done. The analysis indicated that using conventional waste management technology should be possible for disposal of all the advanced process wastes studied for task three. However, some wastes did possess properties that could present special problems for conventional waste management systems. Several task three wastes were self-hardening materials and one was self-heating. Self-hardening is caused by cementitious and pozzolanic reactions that occur when water is added to the waste. All of the self-hardening wastes setup slowly (in a matter of hours or days rather than minutes). Thus these wastes can still be handled with conventional management systems if care is taken not to allow them to setup in storage bins or transport vehicles. Waste self-heating is caused by the exothermic hydration of lime when the waste is mixed with conditioning water. If enough lime is present, the temperature of the waste will rise until steam is produced. It is recommended that self-heating wastes be conditioned in a controlled manner so that the heat will be safely dissipated before the material is transported to an ultimate disposal site. Waste utilization is important because an advanced process waste will not require

Trace elements in coal ash

Science.gov (United States)

Deonarine, Amrika; Kolker, Allan; Doughten, Michael W.

2015-01-01

Coal ash is a residual waste product primarily produced by coal combustion for electric power generation. Coal ash includes fly ash, bottom ash, and flue-gas desulfurization products (at powerplants equipped with flue-gas desulfurization systems). Fly ash, the most common form of coal ash, is used in a range of products, especially construction materials. A new Environmental Protection Agency ruling upholds designation of coal ash as a non-hazardous waste under Subtitle D of the Resource Conservation and Recovery Act, allowing for the continued beneficial use of coal ash and also designating procedures and requirements for its storage.

Pelletised fuel production from coal tailings and spent mushroom compost - Part II. Economic feasibility based on cost analysis

International Nuclear Information System (INIS)

Ryu, Changkook; Khor, Adela; Sharifi, Vida N.; Swithenbank, Jim

2008-01-01

Due to the growing market for sustainable energy, in order to increase the quality of the fuels, pellets are being produced from various materials such as wood and other biomass energy crops, and municipal waste. This paper presents the results from an economic feasibility study for pellet production using blends of two residue materials: coal tailings from coal cleaning and spent mushroom compost (SMC) from mushroom production. Key variables such as the mixture composition, raw material haulage and plant scale were considered and the production costs were compared to coal and biomass energy prices. For both wet materials, the moisture content was the critical parameter that influenced the fuel energy costs. The haulage distance of the raw materials was another factor that can pose a high risk. The results showed that the pellet production from the above two materials can be viable when a less energy-intensive drying process is utilised. Potential market outlets and ways to lower the costs are also discussed in this paper. (author)

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline E. Burgess Clifford; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2007-03-17

This report summarizes the accomplishments toward project goals during the no cost extension period of the third year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts for a third round of testing, the use of a research gasoline engine to test coal-based gasoline, and modification of diesel engines for use in evaluating diesel produced in the project. At the pilot scale, the hydrotreating process was modified to separate the heavy components from the LCO and RCO fractions before hydrotreating in order to improve the performance of the catalysts in further processing. Hydrotreating and hydrogenation of the product has been completed, and due to removal of material before processing, yield of the jet fuel fraction has decreased relative to an increase in the gasoline fraction. Characterization of the gasoline fuel indicates a dominance of single ring alkylcycloalkanes that have a low octane rating; however, blends containing these compounds do not have a negative effect upon gasoline when blended in refinery gasoline streams. Characterization of the diesel fuel indicates a dominance of 3-ring aromatics that have a low cetane value; however, these compounds do not have a negative effect upon diesel when blended in refinery diesel streams. Both gasoline and diesel continue to be tested for combustion performance. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Activated carbons have proven useful to remove the heavy sulfur components, and unsupported Ni/Mo and Ni/Co catalysts have been very effective for

Coal Data: A reference

International Nuclear Information System (INIS)

1991-01-01

The purpose of Coal Data: A Reference is to provide basic information on the mining and use of coal, an important source of energy in the United States. The report is written for a general audience. The goal is to cover basic material and strike a reasonable compromise between overly generalized statements and detailed analyses. The section ''Coal Terminology and Related Information'' provides additional information about terms mentioned in the text and introduces new terms. Topics covered are US coal deposits, resources and reserves, mining, production, employment and productivity, health and safety, preparation, transportation, supply and stocks, use, coal, the environment, and more. (VC)

Coal demand prediction based on a support vector machine model

Energy Technology Data Exchange (ETDEWEB)

Jia, Cun-liang; Wu, Hai-shan; Gong, Dun-wei [China University of Mining & Technology, Xuzhou (China). School of Information and Electronic Engineering

2007-01-15

A forecasting model for coal demand of China using a support vector regression was constructed. With the selected embedding dimension, the output vectors and input vectors were constructed based on the coal demand of China from 1980 to 2002. After compared with lineal kernel and Sigmoid kernel, a radial basis function(RBF) was adopted as the kernel function. By analyzing the relationship between the error margin of prediction and the model parameters, the proper parameters were chosen. The support vector machines (SVM) model with multi-input and single output was proposed. Compared the predictor based on RBF neural networks with test datasets, the results show that the SVM predictor has higher precision and greater generalization ability. In the end, the coal demand from 2003 to 2006 is accurately forecasted. l0 refs., 2 figs., 4 tabs.

Coal Calorific Value Prediction Based on Projection Pursuit Principle

OpenAIRE

QI Minfang; FU Zhongguang; JING Yuan

2012-01-01

The calorific value of coal is an important factor for the economic operation of coal-fired power plant. However, calorific value is tremendous difference between the different coal, and even if coal is from the same mine. Restricted by the coal market, most of coal fired power plants can not burn the designed-coal by now in China. The properties of coal as received are changing so frequently that pulverized coal firing is always with the unexpected condition. Therefore, the researches on the...

Exploration of coal-based pitch precursors for ultra-high thermal conductivity graphite fibers. Final report

Energy Technology Data Exchange (ETDEWEB)

Deshpande, G.V. [Amoco Performance Products, Inc., Alpharetta, GA (United States)

1996-12-27

Goal was to explore the utility of coal-based pitch precursors for use in ultra high thermal conductivity carbon (graphite) fibers. From graphite electrode experience, it was established that coal-based pitches tend to form more highly crystalline graphite at lower temperatures. Since the funding was limited to year 1 effort of the 3 year program, the goal was only partially achieved. The coal-base pitches can form large domain mesophase in spite of high N and O contents. The mesophase reactivity test performed on one of the variants of coal-based pitch (DO84) showed that it was not a good candidate for carbon fiber processing. Optimization of WVU`s isotropic pitch process is required to tailor the pitch for carbon fiber processing. The hetero atoms in the coal pitch need to be reduced to improve mesophase formation.

Petrographic Changes in Compaction Thermal Treatment of Recent Plant Materials, Peat and Coals; Shokubutsu, deitan oyobi sekitan no atsumitsu kanetsu shoributsu no kenbikyo kansatsu

Energy Technology Data Exchange (ETDEWEB)

Sugimoto, Yoshikazu. [National Institute of Materials and Chemical Research, Ibaraki (Japan); Okada, Kiyofumi. [Coal Energy Centre, Saitama (Japan); Suzuki, Yuichiro. [Geological Survey of Japan (Japan)

1999-03-20

Recent plant materials, peat and coals were compressed and thermally treated at various temperatures (200-400degreeC ) for 25 hours. The compaction pyrolysis products were observed with a microscope in both reflected and fluorescent lights, and their vitrinite reflectance (R{sub o}) were also measured. The R{sub o} values of the original samples varied from 0.1 of peat to 0.7 of Miike bituminous coal. After the thermal treatment at 300, 350 and 400degreeC, the R{sub o} values increased to 0.7-1.0, 1.2-1.4 and 1.7-2.1, respectively, in spite of the kind of the original material. The compaction pyrolysis products abtained from plant materials at 200degreeC showed sprcific textures which are often observed in natural low rank coals. Those textures became homogeneous with the increasing temperatures of the thermal treatment. Petrographic characteristice of the xylems of Morwell coal and red pine changed similarly during the thermal treatment. Because peat and humus soil sontained a large amount of mineral matter, they provided the pyrolysis products with different textures from other materials. The fluorercent material of leaf (metasequoia) after the thermal treatment at 200degreeC was considered as cutinite, and it stated to melt around 250degreeC and disappeared around 300degreeC , whereas thet of Miike bituminous coal did not melt and disappear even around 300degreeC. There still remain quite a few coal macerals of which origin and formation are unclear, and the artificial maturation followed by the microsopic investigation is one of effective approaches to elucidate them. (author)

PM2.5 chemical source profiles for vehicle exhaust, vegetative burning, geological material, and coal burning in Northwestern Colorado during 1995

International Nuclear Information System (INIS)

Watson, J.G.; Chow, J.C.; Houck, J.E.

2001-01-01

PM 2.5 (particles with aerodynamic diameters less than 2.5 μm) chemical source profiles applicable to speciated emissions inventories and receptor model source apportionment are reported for geological material, motor vehicle exhaust, residential coal (RCC) and wood combustion (RWC), forest fires, geothermal hot springs; and coal-fired power generation units from northwestern Colorado during 1995. Fuels and combustion conditions are similar to those of other communities of the inland western US. Coal-fired power station profiles differed substantially between different units using similar coals, with the major difference being lack of selenium in emissions from the only unit that was equipped with a dry limestone sulfur dioxide (SO 2 ) scrubber. SO 2 abundances relative to fine particle mass emissions in power plant emissions were seven to nine times higher than hydrogen sulfide (H 2 S) abundances from geothermal springs, and one to two orders of magnitude higher than SO 2 abundances in RCC emissions, implying that the SO 2 abundance is an important marker for primary particle contributions of non-aged coal-fired power station contributions. The sum of organic and elemental carbon ranged from 1% to 10% of fine particle mass in coal-fired power plant emissions, from 5% to 10% in geological material, >50% in forest fire emissions, >60% in RWC emissions, and >95% in RCC and vehicle exhaust emissions. Water-soluble potassium (K + ) was most abundant in vegetative burning profiles. K + /K ratios ranged from 0.1 in geological material profiles to 0.9 in vegetative burning emissions, confirming previous observations that soluble potassium is a good marker for vegetative burning. (Author)

Equilibrium Strategy Based Recycling Facility Site Selection towards Mitigating Coal Gangue Contamination

Directory of Open Access Journals (Sweden)

Jiuping Xu

2017-02-01

Full Text Available Environmental pollution caused by coal gangue has been a significant challenge for sustainable development; thus, many coal gangue reduction approaches have been proposed in recent years. In particular, coal gangue facility (CGF construction has been considered as an efficient method for the control and recycling of coal gangue. Meanwhile, the identification and selection of suitable CGF sites is a fundamental task for the government. Therefore, based on the equilibrium strategy, a site selection approach under a fuzzy environment is developed to mitigate coal gangue contamination, which integrates a geographical information system (GIS technique and a bi-level model to identify candidate CGF sites and to select the most suitable one. In this situation, the GIS technique used to identify potential feasible sites is able to integrate a great deal of geographical data tofitwithpracticalcircumstances;thebi-levelmodelusedtoscreentheappropriatesitecanreasonably dealwiththeconflictsbetweenthelocalauthorityandthecolliery. Moreover,aKarush–Kuhn–Tucker (KKT condition-based approach is used to find an optimal solution, and a case study is given to demonstrate the effectiveness of the proposed method. The results across different scenarios show that appropriate site selection can achieve coal gangue reduction targets and that a suitable excess stack level can realize an environmental-economic equilibrium. Finally, some propositions and management recommendations are given.

Relationships between coal-quality and organic-geochemical parameters: A case study of the Hafik coal deposits (Sivas Basin, Turkey)

Energy Technology Data Exchange (ETDEWEB)

Erik, N. Yalcin; Sancar, S. [Cumhuriyet University, Department of Geological Engineering, Sivas (Turkey)

2010-09-01

This study provides coal-quality, organic-petrographic and organic-geochemical data on Tertiary subbituminous coal of the Hafik area, northwestern part of the Sivas Basin, Turkey. Coal-petrological studies along with proximate and ultimate analyses were undertaken to determine the organic-petrographic characteristics of the Hafik coals. Huminite reflectances were found to be between 0.38 and 0.48% (corresponding to an organic-material-rich and coal layers), values characteristic of low maturity. This parameter shows a good correlation with calorific values (average 21,060 kJ/kg) and average T{sub max} (422 C) mineral-matter diagenesis, indicating immaturity. The studied coals and organic material underwent only low-grade transformation, a consequence of low lithostatic pressure. Therefore, the Hafik coals are actually subbituminous in rank. Rock-Eval analysis results show types II/III and III kerogens. The organic fraction of the coals is mostly comprised of humic-group macerals (gelinites), with small percentages derived from the inertinite and liptinite groups. In this study, organic-petrographic, organic-geochemical and coal quality data were compared. The Hafik deposit is a high-ash, high-sulfur coal. The mineral matter of the coals is comprised mainly of calcite and clay minerals. (author)

Coal and tire burning mixtures containing ultrafine and nanoparticulate materials induce oxidative stress and inflammatory activation in macrophages.

Science.gov (United States)

Gasparotto, Juciano; Somensi, Nauana; Caregnato, Fernanda F; Rabelo, Thallita K; DaBoit, Kátia; Oliveira, Marcos L S; Moreira, José C F; Gelain, Daniel P

2013-10-01

Ultra-fine and nano-particulate materials resulting from mixtures of coal and non-coal fuels combustion for power generation release to the air components with toxic potential. We evaluated toxicological and inflammatory effects at cellular level that could be induced by ultrafine/nanoparticles-containing ashes from burning mixtures of coal and tires from an American power plant. Coal fly ashes (CFA) samples from the combustion of high-S coal and tire-derived fuel, the latter about 2-3% of the total fuel feed, in a 100-MW cyclone utility boiler, were suspended in the cell culture medium of RAW 264.7 macrophages. Cell viability, assessed by MTT reduction, SRB incorporation and contrast-phase microscopy analysis demonstrated that CFA did not induce acute toxicity. However, CFA at 1mg/mL induced an increase of approximately 338% in intracellular TNF-α, while release of this proinflammatory cytokine was increased by 1.6-fold. The expression of the inflammatory mediator CD40 receptor was enhanced by 2-fold, the receptor for advanced glycation endproducts (RAGE) had a 5.7-fold increase and the stress response protein HSP70 was increased nearly 12-fold by CFA at 1mg/mL. Although CFA did not induce cell death, parameters of oxidative stress and reactive species production were found to be altered at several degrees, such as nitrite accumulation (22% increase), DCFH oxidation (3.5-fold increase), catalase (5-fold increase) and superoxide dismutase (35% inhibition) activities, lipoperoxidation (4.2 fold-increase) and sulfhydryl oxidation (40% decrease in free SH groups). The present results suggest that CFA containing ultra-fine and nano-particulate materials from coal and tire combustion may induce sub-chronic cell damage, as they alter inflammatory and oxidative stress parameters at the molecular and cellular levels, but do not induce acute cell death. © 2013.

Synthesis and characterization of zeolite material from coal ashes modified by surfactant; Sintese e caracterizacao de material zeolitico de cinzas de carvao modificado por surfactante

Energy Technology Data Exchange (ETDEWEB)

Fungaro, D.A., E-mail: dfungaro@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (CQMA/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Quimica e Meio Ambiente; Borrely, S.I. [Instituto de Pesquisas Energeticas e Nucleares (CTR/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Tecnologia das Radiacoes

2010-07-01

Coal ash was used as starting material for zeolite synthesis by means of hydrothermal treatment. The surfactant-modified zeolite (SMZ) was prepared by adsorbing the cationic surfactant hexadecyltrimethylammonium bromide (HDTMA-Br) on the external surface of the zeolite from coal ash. The zeolite structure stability was monitored during the characterization of the materials by FTIR, XDR and SEM. The structural parameters of surfactant-modified zeolite are very close to that of corresponding non-modified zeolite which indicates that the crystalline nature of the zeolite remained intact after required chemical treatment with HDTMA-Br molecules and heating treatment for drying. The most intense peaks in the FTIR spectrum of HDTMA-Br were observed in SMZ spectrum confirming adsorption of surfactant on zeolites. (author)

Coal tar pitch. Interrelations between properties and utilization of coal tar pitch

Energy Technology Data Exchange (ETDEWEB)

Collin, G; Koehler, H [Ruetgerswerke A.G., Duisburg (Germany, F.R.)

1977-06-01

Coal tar pitch is won as a highly aromatic, thermoplastic residue by destillating coal tar. In this paper the structure as well as the chemical and physical data of this pitch are introduced. In addition to this the actual as well as possible applications are indicated. For example, the pitch can be used for the production of binders, e.g. for electrodes and road construction as well as in combination with plastics for the production of insulating material and corrosion protection material.

Extraction of hydrocarbon products from shales and coals

Energy Technology Data Exchange (ETDEWEB)

Reed, V Z

1918-05-17

A process is disclosed of extracting hydrocarbon oil matter from petroleum-bearing shales and coals which comprises subjecting a mass of such shale or coal, before distillation to the solvent action of material containing an acid, permitting the solvent material to pass through the mass of shale or coal, and recovering the combined solvent and extracted matter.

Natural Radionuclides in Slag/Ash Pile from Coal-Fired Power Plant Plomin

International Nuclear Information System (INIS)

Barisic, D.; Lulic, S.; Marovic, G.; Sencar, J.

2001-01-01

Full text: The coal slag/ash pile contains about one million tons of different (bottom ash, filter ash, gypsum) waste material deposited in vicinity of Plomin coal-fired power plant. Activities of 40 K, 228 Ra, 226 Ra and 238 U in materials deposited on slag/ash pile as well as in used coals were occasionally measured during past more than two and half decades of Plomin coal-fired plant operation. The radionuclides content in deposited bottom and filter ash material are related with radionuclide activities and mineral matter fraction in coals used. Up to the middle of nineties, the majority of coal used was anthracite from Istrian local mines. In that period, deposited waste material was characterised with relatively high 226 Ra and 238 U activities while potassium and thorium content was very low. When Istrian coal has been completely substituted with imported coal, uranium series radionuclide concentrations in deposited waste materials decreased significantly. Meanwhile, potassium and thorium activities in slag/ash pile material increased. It seems that slag/ash pile material generated in the last several years of Plomin coal-fired power plant operation could be generally used in cement industry without any special restriction. (author)

Determination of total fluorine in five coal reference materials by proton-induced gamma-ray emission spectrometry

Energy Technology Data Exchange (ETDEWEB)

Roelandts, I.; Robaye, G.; Delbrouck-Habaru, J.M.; Weber, G. [University of Liege, Sart (Belgium). Dept. of Geology, Petrology and Geochemistry

1996-03-01

The direct non-destructive proton-induced gamma-ray emission (PIGE) technique with a germanium detector was applied to the determination of total fluorine concentration in five coal reference materials (BCR 30, NIST 1632b, NIST 1635, SARM 20 and USGS CLB-1). Duplicate analyses were made from five randomly selected bottles of each coal. Individual data are presented and some problems (calibration, proton stopping power, effects of sample heating by the proton beam, background estimation) which were encountered during this study are discussed. Sensitivity and reproducibility of the determinations, and homogeneity of the coal samples with respect to fluorine contents by analysis of variance were investigated. The present data are also compared with the few published values for these reference samples, including other PIGE data. The use of synthetic standards and spiked samples in the present study suggested that the PIGE method was more accurate than other techniques.

The production of synthetic material gas (SNG) from pit coal by a combined auto-allothermic steam gasification

International Nuclear Information System (INIS)

Buch, A.

1975-01-01

The steam gasification of pit coal requires temperatures which cannot yet be reached with the present state of HTGR technology for material technical reasons. The use of nuclear heat thus remains limited to some fields of application outside the gasifier, which are specified. The production costs of synthetic natural gas from autothermal gasification on the one hand, and from combined auto-allothermal gasification on the other hand are calculated considering the heat price of pit coal and of the selling price of electrical energy and are compared. (GG/LH) [de

ESTIMATION OF NEAR SUBSURFACE COAL FIRE GAS EMISSIONS BASED ON GEOPHYSICAL INVESTIGATIONS

Science.gov (United States)

Chen-Brauchler, D.; Meyer, U.; Schlömer, S.; Kus, J.; Gundelach, V.; Wuttke, M.; Fischer, C.; Rueter, H.

2009-12-01

Spontaneous and industrially caused subsurface coal fires are worldwide disasters that destroy coal resources, cause air pollution and emit a large amount of green house gases. Especially in developing countries, such as China, India and Malaysia, this problem has intensified over the last 15 years. In China alone, 10 to 20 million tons of coal are believed to be lost in uncontrolled coal fires. The cooperation of developing countries and industrialized countries is needed to enforce internationally concerted approaches and political attention towards the problem. The Clean Development Mechanism (CDM) under the framework of the Kyoto Protocol may provide an international stage for financial investment needed to fight the disastrous situation. A Sino-German research project for coal fire exploration, monitoring and extinction applied several geophysical approaches in order to estimate the annual baseline especially of CO2 emissions from near subsurface coal fires. As a result of this project, we present verifiable methodologies that may be used in the CDM framework to estimate the amount of CO2 emissions from near subsurface coal fires. We developed three possibilities to approach the estimation based on (1) thermal energy release, (2) geological and geometrical determinations as well as (3) direct gas measurement. The studies involve the investigation of the physical property changes of the coal seam and bedrock during different burning stages of a underground coal fire. Various geophysical monitoring methods were applied from near surface to determine the coal volume, fire propagation, temperature anomalies, etc.

Unburned Carbon from Samlaung Coal as Environmental Friendly Sorbent Material

International Nuclear Information System (INIS)

Zaw Naing; Tin Tin Aye; Nyunt Wynn; Kyaw Myo Naing

2005-09-01

The increasing role of coal as a source of energy in the 21st century will demand enviromental and cost-effective strategies for the use of carbonaceous waste products from coal combustion. The carbonaceous in fly ash, unburned carbon (UC), is a potential precursor for the production of adsorbent carbons, since it has gone through a devolatization process while in the combustion, and therefore, only requires to be activated. This paper demonstrates the potential for converting UC from Samlaung coal to activated carbons. After heat activation at 970C, the UC sample was generated to activated carbons having microporous structure. This study concerns with adsorption behavior (decolourization and metal uptake) of UC from Samlaung coal. Batch tests and column tests were carried out. Adsorption isotherms has been obtained from these tests. Results show that the UC have equal or better adsorption capacity comparing with other activated carbons. It was found that heat treatment of Samlaung coal in the presence of air at 970C enhanced the adsorption capacity

Investigation on the activation of coal gangue by a new compound method.

Science.gov (United States)

Li, Chao; Wan, Jianhua; Sun, Henghu; Li, Longtu

2010-07-15

In order to comprehensively utilize coal gangue as the main raw material in cementitious materials, improving its cementitious activity is a question of fundamental importance. In this paper, we present a new compound mechanical-hydro-thermal activation (CMHTA) technology to investigate the activation effect of coal gangue, and the traditional mechanical-thermal activation (TMTA) technology was used as reference. The purpose of this study is to give a detailed comparison between these two methods with regard to the mineral composition, crystal structure and microstructure, by XRD, IR, MAS NMR, XPS and mechanical property analysis. The prepared coal gangue based blended cement, containing 52% of activated coal gangue C (by CMHTA technology), has a better mechanical property than activated coal gangue T (by TMTA technology) and raw coal gangue. The results show that both of the TMTA and CMHTA technologies can improve the cementitious activity of raw gangue greatly. Moreover, compared with TMTA, the mineral phases such as feldspar and muscovite in raw coal gangue were partially decomposed, and the crystallinity of quartz decreased, due to the effect of adding CaO and hydro-thermal process of CMHTA technology. 2010 Elsevier B.V. All rights reserved.

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline E. Burgess Clifford; Andre' Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2006-09-17

This report summarizes the accomplishments toward project goals during the second six months of the third year of the project to assess the properties and performance of coal based products. These products are in the gasoline, diesel and fuel oil range and result from coal based jet fuel production from an Air Force funded program. Specific areas of progress include generation of coal based material that has been fractionated into the desired refinery cuts and examination of carbon material, the use of a research gasoline engine to test coal-based gasoline, and modification of diesel engines for use in evaluating diesel produced in the project. At the pilot scale, the hydrotreating process was modified to separate the heavy components from the LCO and RCO fractions before hydrotreating in order to improve the performance of the catalysts in further processing. Characterization of the gasoline fuel indicates a dominance of single ring alkylcycloalkanes that have a low octane rating; however, blends containing these compounds do not have a negative effect upon gasoline when blended in refinery gasoline streams. Characterization of the diesel fuel indicates a dominance of 3-ring aromatics that have a low cetane value; however, these compounds do not have a negative effect upon diesel when blended in refinery diesel streams. Both gasoline and diesel continue to be tested for combustion performance. The desulfurization of sulfur containing components of coal and petroleum is being studied so that effective conversion of blended coal and petroleum streams can be efficiently converted to useful refinery products. Activated carbons have proven useful to remove the heavy sulfur components, and unsupported Ni/Mo and Ni/Co catalysts have been very effective for hydrodesulfurization. Equipment is now in place to begin fuel oil evaluations to assess the quality of coal based fuel oil. Combustion and characterization of the latest fuel oil (the high temperature fraction of RCO

Trends in the Rare Earth Element Content of U.S.-Based Coal Combustion Fly Ashes.

Science.gov (United States)

Taggart, Ross K; Hower, James C; Dwyer, Gary S; Hsu-Kim, Heileen

2016-06-07

Rare earth elements (REEs) are critical and strategic materials in the defense, energy, electronics, and automotive industries. The reclamation of REEs from coal combustion fly ash has been proposed as a way to supplement REE mining. However, the typical REE contents in coal fly ash, particularly in the United States, have not been comprehensively documented or compared among the major types of coal feedstocks that determine fly ash composition. The objective of this study was to characterize a broad selection of U.S. fly ashes of varied geological origin in order to rank their potential for REE recovery. The total and nitric acid-extractable REE content for more than 100 ash samples were correlated with characteristics such as the major element content and coal basin to elucidate trends in REE enrichment. Average total REE content (defined as the sum of the lanthanides, yttrium, and scandium) for ashes derived from Appalachian sources was 591 mg kg(-1) and significantly greater than in ashes from Illinois and Powder River basin coals (403 and 337 mg kg(-1), respectively). The fraction of critical REEs (Nd, Eu, Tb, Dy, Y, and Er) in the fly ashes was 34-38% of the total and considerably higher than in conventional ores (typically less than 15%). Powder River Basin ashes had the highest extractable REE content, with 70% of the total REE recovered by heated nitric acid digestion. This is likely due to the higher calcium content of Powder River Basin ashes, which enhances their solubility in nitric acid. Sc, Nd, and Dy were the major contributors to the total REE value in fly ash, based on their contents and recent market prices. Overall, this study shows that coal fly ash production could provide a substantial domestic supply of REEs, but the feasibility of recovery depends on the development of extraction technologies that could be tailored to the major mineral content and origins of the feed coal for the ash.

Application of Paste Backfill in Underground Coal Fires

Science.gov (United States)

Masniyom, M.; Drebenstedt, C.

2009-04-01

Coal fires are known from different coalfields worldwide. China, India, USA, Australia, Indonesia and South Africa are the main countries affected by coal fires. The fires is thermally intensive and cause numerous sinkholes, large-scale subsidence, air pollution, global warming, loss of mining productivity and increasing safety risk. The Wuda Inner Mongolia coalfield has been selected as a possible test area for paste backfill. The traditional methods, executed by fire fighting teams, by covering the coalfire areas with soil, blasting burning coal outcrops and injecting water in the subsurface fire pockets are continuously improved and extended. Initiatives to introduce modern techniques, such as backfill placement at fracture and borehole, to cool down the burning coal and cut off the air supply. This study is to investigate backfill materials and techniques suited for underground coal fires. Laboratory tests were carried out on physical, chemical and mechanical properties of different backfill materials and mixtures thereof. Special attention was paid to materials generated as by-products and other cheaply available materials e.g. fly ash from power plants. There is a good chance that one of the different material mixtures investigated can be used as a technically and economically viable backfill for underground coal fires.

Coal industry annual 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-12-01

Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs.

Coal industry annual 1997

International Nuclear Information System (INIS)

1998-12-01

Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs

Nano-mineralogical investigation of coal and fly ashes from coal-based captive power plant (India): An introduction of occupational health hazards

International Nuclear Information System (INIS)

Oliveira, Marcos L.S.; Marostega, Fabiane; Taffarel, Silvio R.; Saikia, Binoy K.; Waanders, Frans B.; DaBoit, Kátia; Baruah, Bimala P.

2014-01-01

Coal derived nano-particles has been received much concern recently around the world for their adverse effects on human health and the environment during their utilization. In this investigation the mineral matter present in some industrially important Indian coals and their ash samples are addressed. Coal and fly ash samples from the coal-based captive power plant in Meghalaya (India) were collected for different characterization and nano-mineralogy studies. An integrated application of advanced characterization techniques such as X-ray diffraction (XRD), High Resolution-Transmission Electron microscopy (HR-TEM)/(Energy Dispersive Spectroscopy) EDS/(selected-area diffraction pattern) SAED, Field Emission-Scanning Electron Microscopy (FE-SEM)/EDS analysis, and Mössbauer spectroscopy were used to know their extent of risks to the human health when present in coal and fly ash. The study has revealed that the coals contain mainly clay minerals, whilst glass fragments, spinel, quartz, and other minerals in lesser quantities were found to be present in the coal fly ash. Fly ash carbons were present as chars. Indian coal fly ash also found to contain nanominerals and ultrafine particles. The coal-fired power plants are observed to be the largest anthropogenic source of Hg emitted to the atmosphere and expected to increase its production in near future years. The Multi Walled Carbon Nano-Tubes (MWCNTs) are detected in our fly ashes, which contains residual carbonaceous matter responsible for the Hg capture/encapsulation. This detailed investigation on the inter-relationship between the minerals present in the samples and their ash components will also be useful for fulfilling the clean coal technology principles. - Highlights: • We research changes in the level of ultrafine and nanoparticles about coal–ash quality. • Increasing dates will increase human health quality in this Indian coal area. • Welfare effects depend on ex-ante or ex-post assumptions about

Coal upgrading

Energy Technology Data Exchange (ETDEWEB)

Nunes, S. [IEA Clean Coal Centre, London (United Kingdom)

2009-10-15

This report examines current technologies and those likely to be used to produce cleaner coal and coal products, principally for use in power generation and metallurgical applications. Consideration is also given to coal production in the leading coal producing countries, both with developed and developing industries. A range of technologies are considered. These include the coal-based liquid fuel called coal water mixture (CWM) that may compete with diesel, the production of ultra-clean coal (UCC) and coal liquefaction which competes with oil and its products. Technologies for upgrading coal are considered, especially for low rank coals (LRC), since these have the potential to fill the gap generated by the increasing demand for coal that cannot be met by higher quality coals. Potential advantages and downsides of coal upgrading are outlined. Taking into account the environmental benefits of reduced pollution achieved through cleaner coal and reduced transport costs, as well as other positive aspects such as a predictable product leading to better boiler design, the advantages appear to be significant. The drying of low rank coals improves the energy productively released during combustion and may also be used as an adjunct or as part of other coal processing procedures. Coal washing technologies vary in different countries and the implications of this are outlined. Dry separation technologies, such as dry jigging and electrostatic separation, are also described. The demonstration of new technologies is key to their further development and demonstrations of various clean coal technologies are considered. A number of approaches to briquetting and pelletising are available and their use varies from country to country. Finally, developments in upgrading low rank coals are described in the leading coal producing countries. This is an area that is developing rapidly and in which there are significant corporate and state players. 81 refs., 32 figs., 3 tabs.

Study on adsorption performance of coal based activated carbon to radioactive iodine and stable iodine

International Nuclear Information System (INIS)

Zhou, Junbo; Hao, Shan; Gao, Liping; Zhang, Youchen

2014-01-01

Highlights: • The impregnated coal-based activated carbons as adsorbent for removing methyl iodide. • The coal-based activated carbons to remove stable iodine. • Iodine residues are under 0.5 μg/ml after adsorption treatment. • The decontamination factor is much higher than 1000. - Abstract: Nuclear power plant, nuclear reactors and nuclear powered ship exhaust contains a large amount of gaseous radioactive iodine, and can damage to the workplace and the surrounding environment. The quantitative test to remove methyl iodide and the qualitative test for removing stable iodine were investigated using the impregnated coal-based activated carbons and coal-based activated carbons as adsorbents. The research conducted in this work shows that iodine residues were under 0.5 μg/ml after adsorption treatment and the decontamination factor of the coal-based activated carbon for removing the stable iodine was more than 1000, which can achieve the purpose of removing harmful iodine, and satisfy the requirement of gaseous waste treatment of nuclear powered vessel and other nuclear plants

Application of EMD-Based SVD and SVM to Coal-Gangue Interface Detection

Directory of Open Access Journals (Sweden)

Wei Liu

2014-01-01

Full Text Available Coal-gangue interface detection during top-coal caving mining is a challenging problem. This paper proposes a new vibration signal analysis approach to detecting the coal-gangue interface based on singular value decomposition (SVD techniques and support vector machines (SVMs. Due to the nonstationary characteristics in vibration signals of the tail boom support of the longwall mining machine in this complicated environment, the empirical mode decomposition (EMD is used to decompose the raw vibration signals into a number of intrinsic mode functions (IMFs by which the initial feature vector matrices can be formed automatically. By applying the SVD algorithm to the initial feature vector matrices, the singular values of matrices can be obtained and used as the input feature vectors of SVMs classifier. The analysis results of vibration signals from the tail boom support of a longwall mining machine show that the method based on EMD, SVD, and SVM is effective for coal-gangue interface detection even when the number of samples is small.

Characterization and supply of coal-based fuels. Quarterly report, February 1, 1989--April 30, 1989

Energy Technology Data Exchange (ETDEWEB)

1989-06-01

Contract objectives are as follows: Develop fuel specifications to serve combustor requirements. Select coals having appropriate compositional and quality characteristics as well as an economically attractive reserve base; Provide quality assurance for both the parent coals and the fuel forms; and deliver premium coal-based fuels to combustor developers as needed for their contract work. Progress is discussed, particulary in slurry fuel preparation and particle size distribution.

Coal liquefaction with preasphaltene recycle

Science.gov (United States)

Weimer, Robert F.; Miller, Robert N.

1986-01-01

A coal liquefaction system is disclosed with a novel preasphaltene recycle from a supercritical extraction unit to the slurry mix tank wherein the recycle stream contains at least 90% preasphaltenes (benzene insoluble, pyridine soluble organics) with other residual materials such as unconverted coal and ash. This subject process results in the production of asphaltene materials which can be subjected to hydrotreating to acquire a substitute for No. 6 fuel oil. The preasphaltene-predominant recycle reduces the hydrogen consumption for a process where asphaltene material is being sought.

A newer concept of setting up coal refineries in coal utilising industries through environmentally sound clean coal technology of organosuper refining of coals

International Nuclear Information System (INIS)

Sharma, D.K.

1994-01-01

In order to reduce the losses of premium organic matter of coal and its immense potential energy which is present in the form of stronger interatomic and intramolecular bonding energies, a newer and convenient technique of recovering the premium organic matter from low grade coals by organosuper-refining technique which operates under ambient pressure conditions has been developed. The residual coal obtained can be used as environmentally clean fuel or as a feedstock for the industries based on carbonization and gasification. It is suggested that a beginning be made by setting up coal refineries in coal utilizing industries on the basis of the presently developed new technology of organosuper-refining of coals to recover premium grade organic chemical feed stocks from coals before utilizing coal by techniques such as bubble bed or recirculatory fluidized bed or pulverized coal combustion in thermal power stations, carbonization in steel plants or other carbonization units, gasification in fertilizer industries or in integrated coal gasification combined cycle power generation. Thus, coal refineries may produce value added aromatic chemical feed stocks, formed coke or coke manufacturing; and carbon fillers for polymers. (author). 100 refs., 1 fig

Enteric virus removal inactivation by coal-based media

Energy Technology Data Exchange (ETDEWEB)

Gupta, A.; Chaudhuri, M. [Indian Institute of Technology, Kanpur (India). Dept. of Civil Engineering

1995-02-01

Four coal-based media, viz. alum-pretreated or ferric hydroxide-impregnated Giridih bituminous coal and lignite (alum-GBC, Fe-GBC; alum-lignite and Fe-Lignite) were laboratory tested to assess their potential in removing/inactivating enteric viruses in water. Batch-sorption screening tests, employing a poliovirus-spiked canal water, indicated high poliovirus sorption by Fe-GBC and alum-GBC in a short contact time of 5 min. Based on the results of further batch-sorption tests, using silver incorporated media (alum/Ag-GBC, alum-GBC-Ag and Fe-GBC-Ag), as well as aesthetic water quality consideration and previous findings on removal of coliforms and turbidity, alum/Ag-GBC, alum-GBC and alum-GBC-AG were included in downflow column studies employing poliovirus-spiked canal water. All three media showed potential in removing/inactivating enteric viruses. In a separate column study employing a joint challenge of poliovirus and rotavirus, alum/Ag-GBC removed 59.3-86.5% of the viruses along with more than 99% reduction in indigenous heterotrophic bacteria. Alum/silver-pretreated bituminous coal medium appears promising for use in household water filters in rural areas of the developing world. However, improved medium preparation to further enhance its efficiency is needed; also, its efficacy in removing/inactivating indigenous enteric bacteria, viruses and protozoa has to be ensured and practicalities or economics of application need to be considered.

Improvements to methods for assisted discharge of coal and ash from storage

Energy Technology Data Exchange (ETDEWEB)

Armstrong, B.; Richards, D.G. [CRE Group Ltd., Stoke Orchard (United Kingdom)

1999-03-01

The project studied the effects of vibration on coal in storage and assessed the effect of changes in vibration parameters, with respect to changes in physical properties of coal, to the flow of material through the storage system. An effective technique was developed for the measurement of transmission of vibration through coal residing in storage vessels, at a variety of scales ranging from laboratory scale to large industrial plant. Significant parameters affecting vibration transmission were impact position (discharge was favoured by application near the outlet), and bulk density of the stored material. Use was made of computer-based discrete element modelling (DEM) techniques for studying vibrations. 27 refs., 62 figs., 13 tabs., 1 app.

Coal information 1996

International Nuclear Information System (INIS)

1997-01-01

Coal Information (1997 edition) is the latest edition of a publication that has been produced annually by the IEA since 1983. The report is intended to provide both Member countries of the OECD and those employed in all sectors of the coal industry with information on current world coal market trends and long-term prospects. It includes information on coal prices, demand, trade, supply, production capacity, transport, environmental issues (including emission standards for coal-fired boilers), coal ports, coal-fired power stations and coal used in non -OECD countries. Part I of the publication contains a wide ranging review of world coal market developments in 1996 and current prospects to 2010. The review is based on historical data of OECD energy supply and demand, data on other world regions, projections of OECD coal supply, demand and trade and information provided by the CIAB. Part II provides, in tabular and graphical form, a more detailed and comprehensive statistical picture of coal developments and future prospects for coal in the OECD, by region and for individual Member countries. Readers interested in projections are strongly advised to read the notes for individual countries in Principles and Definitions in Part II. Coal statistics for non-OECD countries are presented in Part III of the book. Summary data are available on hard coal supply and end-use statistics for about 40 countries and regions world-wide. Data are based on official national submissions to the United Nations in Geneva and New York, national energy publications, information provided to the IEA Secretariat by national statistical offices as well as other unofficial Secretariat sources. Further information on coal used in non-OECD countries is published annually by the IEA in Energy Statistics and Balances of Non-OECD Countries. Also included in Part III are the Survey of Coal Ports world-wide and the Survey of Coal-fired Power Stations in coal-importing countries

Coal-fired power materials - Part II

Energy Technology Data Exchange (ETDEWEB)

Viswanathan, V.; Purgert, R.; Rawls, P. [Electric Power Research Institute, Palo Alto, CA (United States)

2008-09-15

Part 1 discussed some general consideration in selection of alloys for advanced ultra supercritical (USC) coal-fired power plant boilers. This second part covers results reported by the US project consortium, which has extensively evaluated the steamside oxidation, fireside corrosion, and fabricability of the alloys selected for USC plants. 3 figs.

Coal surface control for advanced physical fine coal cleaning technologies

Energy Technology Data Exchange (ETDEWEB)

Morsi, B.I.; Chiang, S.H.; Sharkey, A.; Blachere, J.; Klinzing, G.; Araujo, G.; Cheng, Y.S.; Gray, R.; Streeter, R.; Bi, H.; Campbell, P.; Chiarlli, P.; Ciocco, M.; Hittle, L.; Kim, S.; Kim, Y.; Perez, L.; Venkatadri, R.

1992-01-01

This final report presents the research work carried out on the Coal Surface Control for Advanced Physical Fine Coal Cleaning Technologies project, sponsored by the US Department of Energy, Pittsburgh Energy Technology Center (DOE/PETC). The project was to support the engineering development of the selective agglomeration technology in order to reduce the sulfur content of US coals for controlling SO[sub 2] emissions (i.e., acid rain precursors). The overall effort was a part of the DOE/PETCs Acid Rain Control Initiative (ARCI). The overall objective of the project is to develop techniques for coal surface control prior to the advanced physical fine coal cleaning process of selective agglomeration in order to achieve 85% pyrite sulfur rejection at an energy recovery greater than 85% based on run-of-mine coal. The surface control is meant to encompass surface modification during grinding and laboratory beneficiation testing. The project includes the following tasks: Project planning; methods for analysis of samples; development of standard beneficiation test; grinding studies; modification of particle surface; and exploratory R D and support. The coal samples used in this project include three base coals, Upper Freeport - Indiana County, PA, Pittsburgh NO. 8 - Belmont County, OH, and Illinois No. 6 - Randolph County, IL, and three additional coals, Upper Freeport - Grant County- WV, Kentucky No. 9 Hopkins County, KY, and Wyodak - Campbell County, WY. A total of 149 drums of coal were received.

Life cycle energy use and GHG emission assessment of coal-based SNG and power cogeneration technology in China

International Nuclear Information System (INIS)

Li, Sheng; Gao, Lin; Jin, Hongguang

2016-01-01

Highlights: • Life cycle energy use and GHG emissions are assessed for SNG and power cogeneration. • A model based on a Chinese domestic database is developed for evaluation. • Cogeneration shows lower GHG emissions than coal-power pathway. • Cogeneration has lower life cycle energy use than supercritical coal-power pathway. • Cogeneration is a good option to implement China’s clean coal technologies. - Abstract: Life cycle energy use and GHG emissions are assessed for coal-based synthetic natural gas (SNG) and power cogeneration/polygenereation (PG) technology and its competitive alternatives. Four main SNG applications are considered, including electricity generation, steam production, SNG vehicle and battery electric vehicle (BEV). Analyses show that if SNG is produced from a single product plant, the lower limits of its life cycle energy use and GHG emissions can be comparable to the average levels of coal-power and coal-BEV pathways, but are still higher than supercritical and ultra supercritical (USC) coal-power and coal-BEV pathways. If SNG is coproduced from a PG plant, when it is used for power generation, steam production, and driving BEV car, the life cycle energy uses for PG based pathways are typically lower than supercritical coal-power pathways, but are still 1.6–2.4% higher than USC coal-power pathways, and the average life cycle GHG emissions are lower than those of all coal-power pathways including USC units. If SNG is used to drive vehicle car, the life cycle energy use and GHG emissions of PG-SNGV-power pathway are both much higher than all combined coal-BEV and coal-power pathways, due to much higher energy consumption in a SNG driven car than in a BEV car. The coal-based SNG and power cogeneration technology shows comparable or better energy and environmental performances when compared to other coal-based alternatives, and is a good option to implement China’s clean coal technologies.

Coal competitiveness?

International Nuclear Information System (INIS)

Rogeaux, B.

2006-01-01

Will coal electrical plants be more competitive in the coming years? Answering this one cannot be limited to merely comparing estimates based on reference electricity production costs. The competitiveness of coal will indeed depend on the final product marketed, as the MWhs are not equal: is the purpose to produce base, half-base MWh? Does the electrical equipment structure require flexible MWh (for instance in the event of significant intermittent renewable energy amounts), and therefore plants able to adjust their power rapidly? But the competitiveness of coal will also depend on many factors that will correct reference cost estimates: uncertainties, risks, externalities. These factors will need to be appreciated on a case by case basis. We introduce some of the reasoning used to better appreciate the future competitiveness of coal, and the main factors conditioning it in three contrasting regions of the world: Europe, USA, china. (author)

On-line nuclear ash gauge for coal based on gamma-ray transmission techniques

International Nuclear Information System (INIS)

Rizk, R.A.M.; El-Kateb, A.H.; Abdul-Kader, A.M.

1999-01-01

Developments and applications of on-line nuclear gauges in the coal industry are highly requested. A nuclear ash gauge for coal, based on γ-ray transmission techniques is developed. Single and dual energy γ-ray beams are used to determine the ash content of coal. The percentage ash content as a function of the γ-ray intensities transmitted through coal samples is measured and sensitivity curves are obtained. An empirical formulation relating the ash content values to the γ-ray intensities is derived. Preliminary results show that both single and dual energy γ-ray transmission techniques can be used to give a rapid on-line estimation of the ash concentration values in coal with low cost and reasonable accuracy, but the dual one is much preferable. (author)

Methane of the coal

International Nuclear Information System (INIS)

Vasquez, H.

1997-01-01

In the transformation process of the vegetable material to the coal (Carbonization), the products that are generated include CH 4, CO2, N2 and H2. The methane is generated by two mechanisms: below 50 centigrade degree, as product of microbial decomposition, the methanogenic is generated; and above 50 centigrade degree, due to the effects of the buried and increase of the range of the coal, the thermogenic methane is detachment, as a result of the catagenic. The generated methane is stored in the internal surfaces of the coal, macro and micro pores and in the natural fractures. The presence of accumulations of gas of the coal has been known in the entire world by many years, but only as something undesirable for its danger in the mining exploitation of the coal

[Characterization and supply of coal based fuels]. Quarterly technical report, February 1, 1988--April 30, 1988

Energy Technology Data Exchange (ETDEWEB)

1988-12-31

Contract objectives are as follows: Develop fuel specifications to serve combustor requirements; Select coals having appropriate compositional and quality characteristics as well as an economically attractive reserve base; Provide quality assurance for both the parent coals and the fuel forms; and deliver premium coal-based fuels to combustor developers as needed for their contract work. Progress is described.

Rockburst Disaster Prediction of Isolated Coal Pillar by Electromagnetic Radiation Based on Frictional Effect

Science.gov (United States)

Zhao, Tongbin; Yin, Yanchun; Xiao, Fukun; Tan, Yunliang; Zou, Jianchao

2014-01-01

Based on the understanding that charges generated during coal cracking are due to coal particle friction, a microstructure model was developed by considering four different variation laws of friction coefficient. Firstly, the frictional energy release of coal sample during uniaxial compressive tests was investigated and discussed. Then electromagnetic radiation method was used to predict the potential rockburst disaster in isolated coal pillar mining face, Muchengjian Colliery. The results indicate that the friction coefficient of coal particles decreases linearly with the increase of axial loading force. In predicting the strain-type rockburst, the high stress state of coal must be closely monitored. Field monitoring shows that electromagnetic radiation signal became abnormal before the occurrence of rockburst during isolated coal pillar mining. Furthermore, rockburst tends to occur at the early and ending stages of isolated coal pillar extraction. Mine-site investigation shows the occurrence zone of rockburst is consistent with the prediction, proving the reliability of the electromagnetic radiation method to predict strain-type rockburst disaster. PMID:25054186

Rockburst Disaster Prediction of Isolated Coal Pillar by Electromagnetic Radiation Based on Frictional Effect

Directory of Open Access Journals (Sweden)

Tongbin Zhao

2014-01-01

Full Text Available Based on the understanding that charges generated during coal cracking are due to coal particle friction, a microstructure model was developed by considering four different variation laws of friction coefficient. Firstly, the frictional energy release of coal sample during uniaxial compressive tests was investigated and discussed. Then electromagnetic radiation method was used to predict the potential rockburst disaster in isolated coal pillar mining face, Muchengjian Colliery. The results indicate that the friction coefficient of coal particles decreases linearly with the increase of axial loading force. In predicting the strain-type rockburst, the high stress state of coal must be closely monitored. Field monitoring shows that electromagnetic radiation signal became abnormal before the occurrence of rockburst during isolated coal pillar mining. Furthermore, rockburst tends to occur at the early and ending stages of isolated coal pillar extraction. Mine-site investigation shows the occurrence zone of rockburst is consistent with the prediction, proving the reliability of the electromagnetic radiation method to predict strain-type rockburst disaster.

Surface chemical problems in coal flotation

Science.gov (United States)

Taylor, S. R.; Miller, K. J.; Deurbrouck, A. W.

1981-02-01

As the use of coal increases and more fine material is produced by mining and processing, the need for improved methods of coal beneficiation increases. While flotation techniques can help meet these needs, the technique is beset with many problems. These problems involve surface chemical and interfacial properties of the coal-mineral-water slurry systems used in coal flotation. The problems associated with coal flotation include non-selectivity, inefficient reagent utilization, and excessive variablity of results. These problems can be broadely classified as a lack of predictability. The present knowledge of coal flotation is not sufficient, in terms of surface chemical parameters, to allow prediction of the flotation response of a given coal. In this paper, some of the surface chemical properties of coal and coal minerals that need to be defined will be discussed in terms of the problems noted above and their impact on coal cleaning.

The role of the MHTGR in coal gasification processes

International Nuclear Information System (INIS)

McDonald, C.F.

1988-01-01

The nation will likely become more and more dependent on natural gas and while this will stimulate new exploration and increased production, the time will surely come when global depletion of this resource will require the use of synthetic natural gas (SNG) to support the established nationwide infrastructure. The U.S. is estimated to have coal reserves nearing 500 billion tons that are mineable on an economic base. The Modular High Temperature Gas-Cooled Reactor (MHTGR) steam cycle plant can play an important role in the process of producing SNG from coal to supplement natural gas supplies. Coal-to-gas plants need heat (predominantly steam) and electricity for operation. This energy can be supplied by combustion of coal (autothermal process), but this results in a loss of more than 40% of the coal energy input. From the resource conservation standpoint, using an MHTGR heat source is attractive since much of the valuable fossil raw material can be substituted by clean nuclear energy. Also, air pollution is lowered drastically. This paper highlights how a near-term steam cycle MHTGR plant, based on proven technology and operating in a cogeneration mode, could be coupled with existing coal gasification processes to meet the projected increase in gas consumption in an environmentally acceptable manner

Germanium content in Polish hard coals

Directory of Open Access Journals (Sweden)

Makowska Dorota

2016-01-01

Full Text Available Due to the policy of the European Union, it is necessary to search for new sources of scarce raw materials. One of these materials is germanium, listed as a critical element. This semi-metal is widely used in the electronics industry, for example in the production of semiconductors, fibre optics and solar cells. Coal and fly ash from its combustion and gasification for a long time have been considered as a potential source of many critical elements, particularly germanium. The paper presents the results of germanium content determination in the Polish hard coal. 23 coal samples of various coal ranks were analysed. The samples were collected from 15 mines of the Upper Silesian Coal Basin and from one mine of the Lublin Coal Basin. The determination of germanium content was performed with the use of Atomic Absorption Spectrometry with Electrothermal Atomization (GFAAS. The investigation showed that germanium content in the analysed samples was at least twice lower than the average content of this element in the hard coals analysed so far and was in the range of 0.08 ÷ 1.28 mg/kg. Moreover, the content of Ge in the ashes from the studied coals does not exceed 15 mg/kg, which is lower than the average value of Ge content in the coal ashes. The highest content of this element characterizes coals of the Lublin Coal Basin and young coals type 31 from the Vistula region. The results indicate a low utility of the analysed coal ashes as a source of the recovery of germanium. On the basis of the analyses, the lack of the relationship between the content of the element and the ash content in the tested coals was noted. For coals of the Upper Silesian Coal Basin, the relationship between the content of germanium in the ashes and the depth of the seam was observed.

Rare and Rare-Earth Metals in Coal Processing Waste

Science.gov (United States)

Cherkasova, Tatiana; Cherkasova, Elizaveta; Tikhomirova, Anastasia; Bobrovni-kova, Alyona; Goryunova, Irina

2017-11-01

An urgent issue for power plants operating on solid fuels (coal) is the issue of utilization or use of accumulated production waste - ash and slag materials - in the related production. Ash-slag materials are classified as "waste", usually grade 5; tens of millions of tons of them being pro-duced annually in the Kemerovo region, which threatens the ecology of the region. At the same time, ash and slag is a very promising raw material. The use of this material as a base for the final product allows us to signifi-cantly expand the possibilities of using coal. The most widespread is the system of ash and slag involving in construction or as a replacement for sand in road construction, or as an additive to building mixtures. However, there are both industrially valuable and environmentally dangerous ele-ments in ash-slag materials. Ash-slag materials can be considered as inde-pendent ore deposits located on the surface and requiring the costs of their extraction.

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash.

Science.gov (United States)

Kalaw, Martin Ernesto; Culaba, Alvin; Hinode, Hirofumi; Kurniawan, Winarto; Gallardo, Susan; Promentilla, Michael Angelo

2016-07-15

Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC), which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1) their technical properties are comparable if not better; (2) they can be produced from industrial wastes; and (3) within reasonable constraints, their production requires less energy and emits significantly less CO₂. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC) use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA) and coal bottom ash (CBA), and rice hull ash (RHA). The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF) for elemental and X-ray diffraction (XRD) for mineralogical composition. The raw materials' thermal stability and loss on ignition (LOI) were determined using thermogravimetric analysis (TGA) and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP) analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR), scanning

Analysis of hard coal quality for narrow size fraction under 20 mm

Science.gov (United States)

Niedoba, Tomasz; Pięta, Paulina

2018-01-01

The paper presents the results of an analysis of hard coal quality diversion in narrow size fraction by using taxonomic methods. Raw material samples were collected in selected mines of Upper Silesian Industrial Region and they were classified according to the Polish classification as types 31, 34.2 and 35. Then, each size fraction was characterized in terms of the following properties: density, ash content, calorific content, volatile content, total sulfur content and analytical moisture. As a result of the analysis it can be stated that the best quality in the entire range of the tested size fractions was the 34.2 coking coal type. At the same time, in terms of price parameters, high quality of raw material characterised the following size fractions: 0-6.3 mm of 31 energetic coal type and 0-3.15 mm of 35 coking coal type. The methods of grouping (Ward's method) and agglomeration (k-means method) have shown that the size fraction below 10 mm was characterized by higher quality in all the analyzed hard coal types. However, the selected taxonomic methods do not make it possible to identify individual size fraction or hard coal types based on chosen parameters.

Kinetic comparison of biological and conventional flotation of coal

Energy Technology Data Exchange (ETDEWEB)

Amini, E.; Oliazadeh, M.; Kolahdoozan, M. [University of Queensland, Brisbane, Qld. (Australia)

2009-03-15

Froth flotation is commonly used in coal processing to selectively recover the organic material (coal) from inorganic waste material. Tabas coal, located in east Iran, contains fine disseminated pyrite which is floated with coal during flotation, and hence decreasing the quality of the final concentrate. Reagents, such as sodium cyanide, are typically added to depress pyrite. Due to the toxicity of cyanide, alternative strategies for depressing pyrite flotation are being investigated. In this paper the metallurgical performance of Tabas coal treated with sodium cyanide is compared to that of Tabas coal which has undergone bacterial treatment using Acidithiobacillus ferrooxidans. Results indicate that bacterial treatment decreases the flotation rate of pyrite and improves the selectivity between coal and gangue. The possibility of using bacteria in place of toxic chemicals such as cyanide has significant environmental benefit.

Is coal ash and slag any useful or unloaded wastes?

International Nuclear Information System (INIS)

Botezatu, E.; Grecea, C.; Iacob, O.

2002-01-01

It is well known that all types of coal, like most materials found in nature, contain trace quantities of the naturally occurring primordial radionuclides (uranium and thorium families and potassium-40). Therefore, the combustion of coal results in partitioning of radionuclides included in the non-combustible mineral matter, between the bottom ash and fly ash, and in the release into the environment of large amounts of coal ash. Emissions from thermal power stations in gaseous and particulate form contain radioisotopes arising from the uranium and thorium series as well as from 4 0K . They are discharged into the environment causing changes in the natural radiation background and radiation exposures to the population. The continued releases of these materials to environment may result in a buildup in the air, water and soil of the radionuclides, particularly radium-226. There will be an increase of the basic radiation rate in the neighborhood area of these plants and consequently relatively higher exposure of the local population to radiation. Coal burning is, therefore, one of the sources of technologically enhanced exposure to humans from natural radionuclides (1,2,3,4,5,6). Coal based thermal power plants constitute about 35% of quantum of energy supply in Romania. In view of the importance of coal for energy supply in Romania, we were interested in knowing possible uses of the resulting wastes and minimize the following harmful consequences of coal burning

Nuclear assay of coal. Volume 6. Mass flow devices for coal handling

International Nuclear Information System (INIS)

Anon.

1979-01-01

The mass of coal entering the boiler per unit time is an essential parameter for determinig the total rate of heat input. The mass flow rate of coal on a conveyor belt is generally determined as a product of the instantaneous mass of material on a short section of the belt and the belt velocity. Belt loading could be measured by conventional transducers incorporating mechanical or electromechanical weighers or by gamma-ray attenuation gauge. This report reviews the state of the art in mass flow devices for coal handling. The various methods are compared and commented upon. Special design issues are discussed relative to incorporating a mass flow measuring device in a Continuous On-Line Nuclear Analysis of Coal (CONAC) system

Market-based carbon abatement policies: the case of coal subsidy phase-out

International Nuclear Information System (INIS)

Okogu, B.E.; Birol, F.

1993-01-01

The issue of coal subsidies in industrialized countries is explored and basic econometric techniques are used to quantify the impact on carbon emissions of phasing out such subsidies. Components with other measures for reducing global carbon emissions, such as a carbon or energy tax, deregulation of the coal market has at least equal merit in terms of cost, and it is certainly cheaper than engineering-based approaches, moreover, a policy of coal-subsidy phase-out will have a positive impact on the drive for a cleaner global environment and regional problems, such as acid rain. Coal mining is also an important source of the second major greenhouse gas, methane. Yet coal is the least taxed of all fossil fuels and enjoys significant subsidies in a number of industrialized countries. This raised serious doubts about the real intentions of the proposed new energy and environmental taxes in Europe and North America. (3 figures, 3 tables) (UK)

Width design for gobs and isolated coal pillars based on overall burst-instability prevention in coal mines

Directory of Open Access Journals (Sweden)

Junfei Zhang

2016-08-01

Full Text Available An investigation was conducted on the overall burst-instability of isolated coal pillars by means of the possibility index diagnosis method (PIDM. First, the abutment pressure calculation model of the gob in side direction was established to derive the abutment pressure distribution curve of the isolated coal pillar. Second, the overall burst-instability ratio of the isolated coal pillars was defined. Finally, the PIDM was utilized to judge the possibility of overall burst-instability and recoverability of isolated coal pillars. The results show that an overall burst-instability may occur due to a large gob width or a small pillar width. If the width of the isolated coal pillar is not large enough, the shallow coal seam will be damaged at first, and then the high abutment pressure will be transferred to the deep coal seam, which may cause an overall burst-instability accident. This approach can be adopted to design widths of gobs and isolated coal pillars and to evaluate whether an existing isolated coal pillar is recoverable in skip-mining mines.

Report on the achievements in the Sunshine Project in fiscal 1986. Surveys on coal type selection (coal type survey); 1986 nendo tanshu sentei chosa seika hokokusho. Tanshu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1987-03-01

The purpose of the present study is to elucidate coal quality features of different types of coals and identify the relationship between the coal quality features and the liquefaction characteristics by performing liquefaction characteristic evaluation tests. Based on the result therefrom, a method is established for coal field assessment that can estimate yield of liquefaction in coal fields and coal mines to serve for selection of coal types suitable for liquefaction. Coal quality feature surveys and liquefaction characteristics evaluation tests under the standard conditions have been completed on 48 coal types including Canadian, Australian and American coals. Elucidating the coal quality features of different coals can specify parameters for the coal quality features related to the liquefaction characteristics. Coal ranks elucidate the vitrinite reflectance, structure constituent factors the vitrinite content, composite factors the volatile matter content, quantity of heat generation, and number of H/C and O/C atoms. Investigating the relationship between the coal quality features and the liquefaction characteristics can provide fundamental data for primary screening of raw material coals for liquefaction. The result of the liquefaction characteristics evaluation test under the standard conditions can be the detailed comparative data relative to data derived from the simplified liquefaction characteristics test that is performed to estimate liquefaction yield of specific coal field and coal mine. (NEDO)

Refinery Integration of By-Products from Coal-Derived Jet Fuels

Energy Technology Data Exchange (ETDEWEB)

Caroline Clifford; Andre Boehman; Chunshan Song; Bruce Miller; Gareth Mitchell

2008-03-31

commercial fuels ({approx}60 ON for coal-based gasoline and {approx}20 CN for coal-based diesel fuel). Therefore, the allowable range of blending levels was studied where the blend would achieve acceptable performance. However, in both cases of the coal-based fuels, their ignition characteristics may make them ideal fuels for advanced combustion strategies where lower ON and CN are desirable. Task 3 was designed to develop new approaches for producing ultra clean fuels and value-added chemicals from refinery streams involving coal as a part of the feedstock. It consisted of the following three parts: (1) desulfurization and denitrogenation which involves both new adsorption approach for selective removal of nitrogen and sulfur and new catalysts for more effective hydrotreating and the combination of adsorption denitrogenation with hydrodesulfurization; (2) saturation of two-ring aromatics that included new design of sulfur resistant noble-metal catalysts for hydrogenation of naphthalene and tetralin in middle distillate fuels, and (3) value-added chemicals from naphthalene and biphenyl, which aimed at developing value-added organic chemicals from refinery streams such as 2,6-dimethylnaphthalene and 4,4{prime}-dimethylbiphenyl as precursors to advanced polymer materials. Major advances were achieved in this project in designing the catalysts and sorbent materials, and in developing fundamental understanding. The objective of Task 4 was to evaluate the effect of introducing coal into an existing petroleum refinery on the fuel oil product, specifically trace element emissions. Activities performed to accomplish this objective included analyzing two petroleum-based commercial heavy fuel oils (i.e., No. 6 fuel oils) as baseline fuels and three co-processed fuel oils, characterizing the atomization performance of a No. 6 fuel oil, measuring the combustion performance and emissions of the five fuels, specifically major, minor, and trace elements when fired in a watertube boiler

Proceedings of the workshop on radioactivity associated with coal use

International Nuclear Information System (INIS)

1981-12-01

A workshop on radioactivity in coal use was held on September 15 through 17, 1981, under the auspices of the US Department of Energy, Office of Environmental Programs, and the Los Alamos National Laboratory. The purpose of the workshop was to identify research issues associated with radioactivity resulting from the use of coal for electric power generation. The concensus of the 10 scientists participating in the workshop was that a moderate to strong need exists for research in solubility of fly ash in different fluids and for determination of radioactivity in construction materials. Several additional research issues were identified but were given a lower priority. Summaries of each presentation are included. Titles are: some effects of coal combustion on the radiation environment; radionuclides in western coal at Mound; low-level radiation in coals utilized and ashes produced at New York State electric utilities; radioactivity from coal use - where are the problems; chemistry of radionuclides in coal preparation; uranium daughters in natural atmospheric aerosols and coal-fired power plant emissions; possible contributions of coal extraction and utilization to radioactivity contributions in drinking water; and impact on water quality from radionuclides in coal. One paper has been abstracted separately for inclusion in the Energy Data Base

On the analysis of building a public information platform based on e-Commerce for coal logistics

Directory of Open Access Journals (Sweden)

Zeguo Qiu

2013-09-01

Full Text Available Purpose: Putting forward the concept and features of the public information platform for coal logistics based on electronic commerce, as well as the requirements of upper and lower intersections of the coal supply chain. Meanwhile, this paper will also probe into the current condition of statistics management in coal logistics, and then discuss how to build a public information platform based on electronic commerce for coal logistics. Design/methodology/approach: According to the further exploring the concepts and relevant characteristics and the development of coal logistics and supply chain management in China of the current period. Findings/ Practical implications: An advanced public information platform for coal logistics utilizes to best advantage modern information technologies and managerial concepts in the operation of coal logistics, such as e-commerce, e-information, supply chain management, etc. This not only stimulates efficient integration of business flow, information flow, logistics and capital flow of the coal industry, brings about in-depth integration of the logistics resources of the coal industry, but also greatly improves the efficiency of the operation of coal logistics, reduces the cost of coal logistics, and enhances the overall competitiveness of upstream and downstream companies along the coal supply chain. Research limitations/implications: Although the coal logistics public information platform has been applied in some enterprises in China, not yet in a broader range of applications, which need the joint efforts of all parties. Originality/value: Fitted to the e-commerce era, the Public Information Platform for Coal Logistics envisioned in this article is highly feasible and worthy of reference to relevant institutions.

Analysis of the relationship between the coal properties and their liquefaction characteristics by using the coal data base; Tanshu data base ni yoru tanshitsu to ekika tokusei no kaiseki

Energy Technology Data Exchange (ETDEWEB)

Kanbayashi, Y.; Okada, K. [Coal Mining Research Center, Tokyo (Japan)

1996-10-28

The relationship between coal properties and liquefaction or gasification characteristics was analyzed by using the analysis and test results and liquefaction characteristics in the coal data base. On liquefaction reaction, the close relation between an oil yield and coal constituent composition or a coal rank is well-known. Various multivariable regression analyses were conducted by using 6 factors as variables such as calorific value, volatile component, O/C and H/C atomic ratios, exinite+vitrinite content and vitrinite reflectance, and liquefaction characteristics as variate. On liquefaction characteristics, the oil yield of dehydrated and deashed coals, asphaltene yield, hydrogen consumption, produced water and gas quantities, and oil+asphaltene yield were predicted. The theoretical gasification efficiency of each specimen was calculated to evaluate the liquefaction reaction obtained. As a result, the oil yield increased with H/C atomic ratio, while the theoretical gasification efficiency increased with O/C atomic ratio. 5 figs., 1 tab.

Risk Evaluation of Railway Coal Transportation Network Based on Multi Level Grey Evaluation Model

Science.gov (United States)

Niu, Wei; Wang, Xifu

2018-01-01

The railway transport mode is currently the most important way of coal transportation, and now China’s railway coal transportation network has become increasingly perfect, but there is still insufficient capacity, some lines close to saturation and other issues. In this paper, the theory and method of risk assessment, analytic hierarchy process and multi-level gray evaluation model are applied to the risk evaluation of coal railway transportation network in China. Based on the example analysis of Shanxi railway coal transportation network, to improve the internal structure and the competitiveness of the market.

Coal background paper. Coal demand

International Nuclear Information System (INIS)

1997-01-01

Statistical data are presented on coal demands in IEA and OECD member countries and in other countries. Coal coaking and coaking coal consumption data are tabulated, and IEA secretariat's coal demand projections are summarized. Coal supply and production data by countries are given. Finally, coal trade data are presented, broken down for hard coal, steam coal, coking coal (imports and export). (R.P.)

A Fiber Bragg Grating-Based Monitoring System for Roof Safety Control in Underground Coal Mining

Directory of Open Access Journals (Sweden)

Yiming Zhao

2016-10-01

Full Text Available Monitoring of roof activity is a primary measure adopted in the prevention of roof collapse accidents and functions to optimize and support the design of roadways in underground coalmines. However, traditional monitoring measures, such as using mechanical extensometers or electronic gauges, either require arduous underground labor or cannot function properly in the harsh underground environment. Therefore, in this paper, in order to break through this technological barrier, a novel monitoring system for roof safety control in underground coal mining, using fiber Bragg grating (FBG material as a perceived element and transmission medium, has been developed. Compared with traditional monitoring equipment, the developed, novel monitoring system has the advantages of providing accurate, reliable, and continuous online monitoring of roof activities in underground coal mining. This is expected to further enable the prevention of catastrophic roof collapse accidents. The system has been successfully implemented at a deep hazardous roadway in Zhuji Coal Mine, China. Monitoring results from the study site have demonstrated the advantages of FBG-based sensors over traditional monitoring approaches. The dynamic impacts of progressive face advance on roof displacement and stress have been accurately captured by the novel roadway roof activity and safety monitoring system, which provided essential references for roadway support and design of the mine.

Direct energy balance based active disturbance rejection control for coal-fired power plant.

Science.gov (United States)

Sun, Li; Hua, Qingsong; Li, Donghai; Pan, Lei; Xue, Yali; Lee, Kwang Y

2017-09-01

The conventional direct energy balance (DEB) based PI control can fulfill the fundamental tracking requirements of the coal-fired power plant. However, it is challenging to deal with the cases when the coal quality variation is present. To this end, this paper introduces the active disturbance rejection control (ADRC) to the DEB structure, where the coal quality variation is deemed as a kind of unknown disturbance that can be estimated and mitigated promptly. Firstly, the nonlinearity of a recent power plant model is analyzed based on the gap metric, which provides guidance on how to set the pressure set-point in line with the power demand. Secondly, the approximate decoupling effect of the DEB structure is analyzed based on the relative gain analysis in frequency domain. Finally, the synthesis of the DEB based ADRC control system is carried out based on multi-objective optimization. The optimized ADRC results show that the integrated absolute error (IAE) indices of the tracking performances in both loops can be simultaneously improved, in comparison with the DEB based PI control and H ∞ control system. The regulation performance in the presence of the coal quality variation is significantly improved under the ADRC control scheme. Moreover, the robustness of the proposed strategy is shown comparable with the H ∞ control. Copyright © 2017. Published by Elsevier Ltd.

Scenario-Based Analysis on Water Resources Implication of Coal Power in Western China

Directory of Open Access Journals (Sweden)

Jiahai Yuan

2014-10-01

Full Text Available Currently, 58% of coal-fired power generation capacity is located in eastern China, where the demand for electricity is strong. Serious air pollution in China, in eastern regions in particular, has compelled the Chinese government to impose a ban on the new construction of pulverized coal power plants in eastern regions. Meanwhile, rapid economic growth is thirsty for electric power supply. As a response, China planned to build large-scale coal power bases in six western provinces, including Inner Mongolia, Shanxi, Shaanxi, Xinjiang, Ningxia and Gansu. In this paper, the water resource implication of the coal power base planning is addressed. We find that, in a business-as-usual (BAU scenario, water consumption for coal power generation in these six provinces will increase from 1130 million m3 in 2012 to 2085 million m3 in 2020, experiencing nearly a double growth. Such a surge will exert great pressure on water supply and lead to serious water crisis in these already water-starved regions. A strong implication is that the Chinese Government must add water resource constraint as a critical point in its overall sustainable development plan, in addition to energy supply and environment protection. An integrated energy-water resource plan with regionalized environmental carrying capacity as constraints should be developed to settle this puzzle. Several measures are proposed to cope with it, including downsizing coal power in western regions, raising the technical threshold of new coal power plants and implementing retrofitting to the inefficient cooling system, and reengineering the generation process to waterless or recycled means.

Self-Scrubbing Coal -- an integrated approach to clean air

Energy Technology Data Exchange (ETDEWEB)

Harrison, K.E. [Custom Coals Corp., Pittsburgh, PA (United States)

1997-12-31

Carefree Coal is coal cleaned in a proprietary dense-media cyclone circuit, using ultrafine magnetite slurries, to remove noncombustible material, including up to 90% of the pyritic sulfur. Deep cleaning alone, however, cannot produce a compliance fuel from coals with high organic sulfur contents. In these cases, Self-Scrubbing Coal will be produced. Self-Scrubbing Coal is produced in the same manner as Carefree Coal except that the finest fraction of product from the cleaning circuit is mixed with limestone-based additives and briquetted. The reduced ash content of the deeply-cleaned coal will permit the addition of relatively large amounts of sorbent without exceeding boiler ash specifications or overloading electrostatic precipitators. This additive reacts with sulfur dioxide (SO{sub 2}) during combustion of the coal to remove most of the remaining sulfur. Overall, sulfur reductions in the range of 80--90% are achieved. After nearly 5 years of research and development of a proprietary coal cleaning technology coupled with pilot-scale validation studies of this technology and pilot-scale combustion testing of Self-Scrubbing Coal, Custom Coals Corporation organized a team of experts to prepare a proposal in response to DOE`s Round IV Program Opportunity Notice for its Clean Coal Technology Program under Public Law 101-121 and Public Law 101-512. The main objective of the demonstration project is the production of a coal fuel that will result in up to 90% reduction in sulfur emissions from coal-fired boilers at a cost competitive advantage over other technologies designed to accomplish the same sulfur emissions and over naturally occurring low sulfur coals.

Coal Corporation of Victoria annual report 1986

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

Information is presented on operations, strategic planning, brown coal production and finance. Divisional reports are presented for the following divisions of the Coal Corporation of Victoria: marketing, technical marketing and special projects, research and development, and corporate services. The activities of the technical marketing and special projects division are discussed under the following headings: the coal for industry programme, the Brown Coal Liquefaction (Victoria) Pty. Ltd. project, dried brown coal activities, and resource development planning and policy activities. The corporation is currently conducting research into the following areas: ion exchange materials, activated carbons, and horticultural and agricultural applications of brown coal.

Microscopical characterization of carbon materials derived from coal and petroleum and their interaction phenomena in making steel electrodes, anodes and cathode blocks for the Microscopy of Carbon Materials Working Group of the ICCP

Science.gov (United States)

Predeanu, G.; Panaitescu, C.; Bălănescu, M.; Bieg, G.; Borrego, A.G.; Diez, M. A.; Hackley, Paul C.; Kwiecińska, B.; Marques, M.; Mastalerz, Maria; Misz-Kennan, M.; Pusz, S.; Suarez-Ruiz, I.; Rodrigues, S.; Singh, A. K.; Varma, A. K.; Zdravkov, A.; Zivotić, D.

2015-01-01

This paper describes the evaluation of petrographic textures representing the structural organization of the organic matter derived from coal and petroleum and their interaction phenomena in the making of steel electrodes, anodes and cathode blocks.This work represents the results of the Microscopy of Carbon Materials Working Group in Commission III of the International Committee for Coal and Organic Petrology between the years 2009 and 2013. The round robin exercises were run on photomicrograph samples. For textural characterization of carbon materials the existing ASTM classification system for metallurgical coke was applied.These round robin exercises involved 15 active participants from 12 laboratories who were asked to assess the coal and petroleum based carbons and to identify the morphological differences, as optical texture (isotropic/anisotropic), optical type (punctiform, mosaic, fibre, ribbon, domain), and size. Four sets of digital black and white microphotographs comprising 151 photos containing 372 fields of different types of organic matter were examined. Based on the unique ability of carbon to form a wide range of textures, the results showed an increased number of carbon occurrences which have crucial role in the chosen industrial applications.The statistical method used to evaluate the results was based on the “raw agreement indices”. It gave a new and original view on the analysts' opinion by not only counting the correct answers, but also all of the knowledge and experience of the participants. Comparative analyses of the average values of the level of overall agreement performed by each analyst in the exercises during 2009–2013 showed a great homogeneity in the results, the mean value being 90.36%, with a minimum value of 83% and a maximum value of 95%.

Certification of the contents (mass fraction) of carbon, hydrogen, nitrogen, chlorine, arsenic, cadmium, manganese, mercury, lead, selenium, vanadium and zinc in three coals. Gas coal CRM No. 180; Coking coal CRM No. 181; Steam coal CRM No. 182

Energy Technology Data Exchange (ETDEWEB)

Griepink, B; Colinet, E; Wilkinson, H C

1986-01-01

The report first describes the preparation of three coal reference materials: Gas coal (BCR No. 180), Coking coal (BCR No. 181) and Steam coal (BCR No. 182). It deals further with the homogeneity and stability tests for major, minor and trace components. The contents (mass fractions) of the elements: C, H, N, Cl, As, Cd, Mn, Hg, Pb, Se, V and Zn are certified. The analytical techniques used in the certification are summarised. All the individual results are given and recommendations for analysis are made.

Report of base consolidation promotion survey of overseas coal import in FY 1993. Feasibility survey of effective utilization of coal ash; 1993 nendo kaigaitan yunyu kiban seibi sokushin chosa. Sekitanbai yuko riyo jigyo no feasibility chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This report describes the effective utilization of coal ash discharged from general industry (general industry ash) as improving material of construction waste soil and deodorant for poultry industry. Coal ash is characterized by the pozzolan and self-hardening properties which are not shown in soil and sand. Coal ash having a large amount of free CaO in its composition has stronger such properties. Coal ash generated from fluidized bed combustor which is a kind of combustor of coal contains a large amount of free CaO, especially, resulting in the stronger such properties. On the other hand, coal ash has water and oil absorbing property due to its porous structure. To utilize these properties, the improving material of soft construction waste soil and deodorant for poultry industry have been selected. As a result of laboratory and field tests for the former, it was found that sufficient supporting force can be obtained. Since the protection of powder splash is required at the site, a humidification system has been developed, which can protect the splash by the humidification of 5%. The price between 500 and 1,000 yen/ton is suitable for the improving material of construction waste soil. The maximum price of the deodorant for poultry industry is 10 yen/kg. 14 refs., 40 figs., 49 tabs.

Coal-to-liquid

Energy Technology Data Exchange (ETDEWEB)

Cox, A.W.

2006-03-15

With crude oil prices rocketing, many of the oil poor, but coal rich countries are looking at coal-to-liquid as an alternative fuel stock. The article outlines the two main types of coal liquefaction technology: direct coal liquefaction and indirect coal liquefaction. The latter may form part of a co-production (or 'poly-generation') project, being developed in conjunction with IGCC generation projects, plus the production of other chemical feedstocks and hydrogen. The main part of the article, based on a 'survey by Energy Intelligence and Marketing Research' reviews coal-to-liquids projects in progress in the following countries: Australia, China, India, New Zealand, the Philippines, Qatar and the US. 2 photos.

Electrochemistry of carbonaceous materials; 1. Oxidation of Sardinian coal by Fe(III) ions

Energy Technology Data Exchange (ETDEWEB)

Tomat, R.; Salmaso, R.; Zecchin, S. (CNR-Instituto di Polarografia ed Elettrochimica Preparativa, Padova (Italy))

1992-04-01

Oxidation of subbitiminous coal (Sulcis basin, Sardinia, Italy) by Fe(III) ions in aqueous H{sub 2}SO{sub 4} solution was investigated over a wide temperature range (20-80{degree}C). Experimental results are in accord with a reaction scheme involving a reversible complex between coal particles and Fe(III) ions as a first step in the oxidation process. At low coal concentration, the reaction rate follows first-order kinetics in both coal and ferric ions (overall second order), while at sufficiently high coal concentration, the reaction rate is consistent with first-order kinetics in Fe(III) concentration, appearing to be independent of coal concentration. The kinetic results obtained give preliminary information on the advantageous use of the Fe(III)/slurried coal reaction system to depolarize the anodic compartment of an electrolysis cell, for the production of H{sub 2}. 11 refs., 5 figs.

China’s farewell to coal: A forecast of coal consumption through 2020

International Nuclear Information System (INIS)

Hao, Yu; Zhang, Zong-Yong; Liao, Hua; Wei, Yi-Ming

2015-01-01

In recent decades, China has encountered serious environmental problem, especially severe air pollution that has affected eastern and northern China frequently. Because most air pollutants in China are closely related to coal combustion, the restriction of coal consumption is critical to the improvement of the environment in China. In this study, a panel of 29 Chinese provinces from 1995 to 2012 is utilized to predict China’s coal consumption through 2020. After controlling for the spatial correlation of coal consumption among neighboring provinces, an inverted U-shaped Environmental Kuznets Curve (EKC) between coal consumption per capita and GDP per capita in China is detected. Furthermore, based on the estimation results and reasonable predictions of key control variables, China’s provincial and national coal consumption through 2020 is forecasted. Specifically, under the benchmark scenario, consumption is expected to continue growing at a decreasing rate until 2020, when China’s coal consumption would be approximately 4.43 billion tons. However, if China can maintain relatively high growth rate (an annual growth rate of 7.8 percent), the turning point in total coal consumption would occur in 2019, with projected consumption peaking at 4.16 billion tons. - Highlights: • Provincial panel data is used to investigate the influential factors of coal consumption in China. • The spatial correlations of coal consumption in neighboring provinces are fully considered. • An inverted-U shaped Environmental Kuznets Curve for coal consumption in China has been found. • Based on the estimation results, China’s national coal consumption before 2020 is forecasted. • Under the basic scenario, China’s national coal consumption will grow at a decreasing speed till 2020.

Utilization of coal fired power plant by-products. Utilization of coal ash; Sekitan karyoku ni okeru fukusanbutsu no yuko riyo gijutsu. Sekitanbai no yuko riyo

Energy Technology Data Exchange (ETDEWEB)

Kishimoto, K. [The Federation of Electric Power Companies, Tokyo (Japan); Watanabe, M. [Electric Power Development Co. Ltd., Tokyo (Japan)

1997-11-05

The paper introduced the present situation and future task of the tackling with effective use of coal ash discharged from coal thermal power plants. Making the use of the characteristics, coal ash is mostly used in the fields of cement/concrete, civil engineering/construction, and agriculture/forestry/fisheries. In the case of using fly ash to concrete, the effects are the heightening of long-term strength, increase in workability, decrease in hydration heat, control of alkali aggregate reaction, etc. In the civil engineering/construction field, coal ash is allowed to be used for road bed material and mixed civil engineering material as road materials, for revetment back-filling material, soft ground surface layer treatment, soft ground/soil improvement materials, FGC deep layer mixing treatment process, SPC (sand compaction pile) material, etc. as earth work materials. Besides, it is used for light coarse aggregate, light sand, etc., as construction materials, for material substituting ceramics products, etc. as building materials, and for agricultural material, potassium silicate fertilizer and ocean structure in the agriculture/forestry/fisheries field. 4 refs., 2 tabs.

CoalFleet for tomorrow. An industry initiative to accelerate the deployment of advanced coal-based generation plants

Energy Technology Data Exchange (ETDEWEB)

Parkes, J.; Holt, N.; Phillips, J. [Electric Power Research Institute (United States)

2006-07-01

The industry initiative 'CoalFleet for tomorrow' was launched in November 2004 to accelerate the deployment and commercialization of clean, efficient, advanced coal power systems. This paper discusses the structure of CoalFleet and its strategy for reducing the cost, leadtime and risk of deploying advanced coal technologies such as combined-cycle power plants. 6 figs.

FY 1994 report on the Coal Gasification Committee; 1994 nendo sekitan gasuka iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The paper reported activities of the Coal Gasification Committee in FY 1994. The 1st Coal Gasification Committee Meeting was held on May 18,1994, the 2nd Meeting on October 28, 1994, and the 3rd Meeting on February 21, 1995. Report/discussion were made about activities of each section meeting and the progress of the development of coal gasification technology. For the 50 t/d HYCOL pilot plant, disassembly examination was conducted. As a result of the examination, the high-temperature gas corrosion caused by gas product against metal members was negligible, but against members in the wet corrosion environment, SCC, intergranular corrosion and pitting corrosion were generated. About members used in the high-temperature environment, it was made clear that Ir was applicable to thermowell, high chromia-base sintered products were applicable to non-cooling hearth tapping materials, and high chromia-base indeterminate-formed materials were applicable to water-cooled fireproofing wall. Based on the data obtained through the operational study of a 50 t/d pilot plant, conceptual design was made of a coal gasification hydrogen production plant of a scale of demonstration plant. (NEDO)

Stress analysis of longwall top coal caving

Energy Technology Data Exchange (ETDEWEB)

Alehossein, H.; Poulsen, B.A. [CSIRO Exploration & Mining, Brisbane, Qld. (Australia)

2010-01-15

Longwall top coal caving (LTCC) is a relatively new method of mining thick coal seams that is currently achieving high productivity and efficiency. The technique is similar to traditional longwall mining in that a cutting head slices coal from the lower section of the coal seam onto a conveyor belt installed in front of the hydraulic support near the cutting face. In modern LTCC an additional rear conveyor belt is located behind the support, to which the flow of the caved coal from the upper part of the seam can be controlled by a moveable flipper attached to the canopy of the support. The mining method relies on the fracturing of the top coal by the front abutment pressure to achieve satisfactory caving into the rear conveyor. This paper develops a yield and caveability criterion based on in situ conditions in the top coal in advance of the mining face (yield) and behind the supports (caveability). Yielding and caving effects are combined into one single number called caving number (CN), which is the multiplication result of caving factor (CF) and yield factor (YF). Analytical derivations are based on in situ stress conditions, Mohr-Coulomb and/or Hoek-Brown rock failure criteria and an on-associated elastoplastic strain softening material behaviour. The yield and caveability criteria are in agreement with results from both numerical studies and mine data. The caving number is normalised to mining conditions of a reference Chinese mine (LMX mine) and is used to assess LTCC performance at fourteen other Chinese working longwalls that have had varying success with the LTCC technology. As a predictive model, results of this analytical/numerical study are useful to assess the potential success of caving in new LTCC operations and in different mining conditions.

Activated carbons from Mongolian coals by thermal treatment

Directory of Open Access Journals (Sweden)

A Ariunaa

2014-09-01

Full Text Available Mongolian different rank coals were used as raw material to prepare activatedcarbons by physical activation method. The coal derived carbons were oxidized with nitric acid in order to introduce surface oxygen groups. The ultimate elemental analysis, scanning electron microscopy, surface area, pore size distribution analysis and selective neutralization method were used to characterize the surface properties of activated carbons, oxidizedcarbons and raw coals. The effect of coal grade on the adsorption properties of the carbons were studied. It was concluded that Naryn sukhait bituminous coal could be serve as suitable raw material for production of activated carbons for removal of heavy metal ions from solution.DOI: http://dx.doi.org/10.5564/mjc.v12i0.174 Mongolian Journal of Chemistry Vol.12 2011: 60-64

Briquetting of Coke-Brown Coal Mixture

Directory of Open Access Journals (Sweden)

Ïurove Juraj

1998-09-01

Full Text Available The paper presents the results of the research of briquetting a coke-brown coal composite The operation consists of the feeding crushed coal and coke to moulds and pressing into briquettes which have been made in the Laboratories at the Mining Faculty of Technical University of Košice (Slovakia. In this research, all demands will be analyzed including the different aspects of the mechanical quality of briquettes, the proportion of fine pulverulent coal and coke in bricks, the requirements for briquetting the coke-brown coal materials.

Preparation of briquettes on the basis of desintegrated phyto-materials and the admixture of fine-grained coal and coke

Directory of Open Access Journals (Sweden)

Jakabský Štefan

2002-03-01

Full Text Available The contribution deals with the preparation of small-diameter briquettes on the basis of desintegrated phyto-materials and the admixture of coal and coke. The phyto-materials are classified as a dry biomass that can be, on the one hand, the wastes from wood-working industry,(sawdust, chips, bark, etc. or dried mass from the plant production and, on the other hand, the mass of quick-growing plants cultivated on special plantations. In present time this renewable energy resource attracts attention by its heating value ranging from 10 to 16 MJ.kg-1 (EkoWATT, 2001, a low ash content of 0.5 – 6.5 % and by a low sulphur content in a water free sample of 0.05 –0.12 %.As a phyto-material the spruce sawdusts having a grain size of –2 mm were used. The admixture of brown coal, hard coal and coke with a grain size of 0.040 mm was added to the sawdust and in such way prepared mixtures were subjected to briquetting with the aim to obtain small-diameter briquettes. The influence of admixtures amount on the density, and the suitable briquetting press have been studied. A saleability of briquettes on the basis of phyto-materials is conditioned by their density that must be higher than 1,000 kg.m-3. Thus, an adding of denser material with a relatively high calorific value would enable to attain the required density as well as to retain and/or to improve the main utility properties, i.e. calorific value and ash content.The adding evinces itself in an enhancement of briquetting press, but also density of obtained briquettes is often much higher that required by the market. It was showed that in the case of clear spruce sawdust the density of 1,059 kg.m-3 under the briquetting press of 250 MPa can be attained. According to other results, an admixture of brown coal is not very favourable because briquetting press exceeds the value of 300 MPa. As to hard coal adding, the presses under 250 MPa were achieved at the content of 25 – 30 %. The density of these

Comparison of costs of electricity generation based on nuclear energy and pit coal

International Nuclear Information System (INIS)

1981-01-01

Despite of a meanwhile considerable increase in costs of installation, especially of nuclear power stations, the differences in costs have increased in favour of nuclear electricity generation. The cost advantages are estimated 4 German Pfennig per kilowatt-hour in the base-load field for plants coming into operation at the end of this decade compared with the most profitable variant of pit coal utilization on which this investigation is based; compared to the use of German hard coal, assuming a relatively optimistic development of prices for domestic hard coal in the future, the cost advantage is estimated 8 German Pfennig per kilowatt-hour. The main reason is that in the past years the price for German hard coal as well as for imported coal considerably rose and for the future further increases have to be expected whereas the largest share of the costs of nuclear electricity generation doesn't increase, after the plant is completed. Considering the importance of the fuel costs within the total costs of electricity generation in coal power stations this must have its effects on the total result. These results also prove to be valid for a variation of important cost parameters. Only if the unlikely assumption that considerable variations of influences on costs - each unfavourable effecting nuclear electricity generation - would come together would prove to be true the economic efficiency of nuclear energy would be reduced or questioned. (UA) [de

Interaction and the structures of coal

Science.gov (United States)

Opaprakasit, Pakorn

The origin of a decrease in the amount of soluble material from coal upon a reflux treatment has been investigated in an attempt to obtain insight into the nature of the interaction in the macromolecular network structure of coal. This decrease in the extractable material is a result of an increase in the amount of physical cross-links associated with secondary interactions. The alternate possibility of covalent cross-link formation by ether linkage was found to be unlikely because the coal hydroxyl content remains unchanged upon heat treatment. The functional groups responsible for forming these physical cross-links and their contents vary from coal to coal with coal rank. Carboxylate/cation complexes, similar to those found in ionomers, dominate in low rank coal. In high rank coal, the clusters involving pi-cation interactions were observed. Both mechanisms seem to play a role in mid rank coals. These physical cross-links are responsible for a lowering of the extraction yield of coal, but are disrupted by a treatment with acid solution, resulting in an increase in the extraction yield. As a consequence, the cross-links in coal structure should be classified into two types; a "permanent" covalent cross-link, which break under extreme conditions such as chemical reaction and pyrolysis, and "reversible" cross-links, largely associated with ionomer-like structure and pi-cation interactions. The interaction between a "magic" solvent of N-methylpyrollidone and carbon disulfide (NMP/CS2) and its role in the unusual extractability enhancement of Upper Freeport coal has also been investigated. The results strongly suggest that NMP/CS2 mixed solvents form complexes with cations. These mixed solvents are capable of forming a solid complex with cations from NaOH and some simple salts, such as NaCl and LiCl. Given that Upper Freeport coal contains a large amount of mineral matter, it is not surprising that these types of complexes could be formed in the present of the mixed

Distilling coal, shale, etc

Energy Technology Data Exchange (ETDEWEB)

Bussey, C C

1916-07-17

In the extraction of vovolatile ingredients from coal, shale, lignite, and other hydrocarbonaceous materials by passing through the material a heating-agent produced by burning at the base of the charge a portion of the material from which the volatile ingredients have been extracted, the temperature of the heating agent is maintained constant by continuously removing the residue from the bottom of the apparatus. The temperature employed is 800/sup 0/F or slightly less, so as to avoid any breaking-down action. As shown the retort is flared downwardly, and is provided at the base with a fireplace, which is in communication with the interior of the retort through flues fitted with screens and dampers. Beneath the bottom of the retort is mounted a movable grate carried on endless sprocket chains, which are preferably set so that the grate inclines downwardly towards the coke, etc.

Rare and Rare-Earth Metals in Coal Processing Waste

Directory of Open Access Journals (Sweden)

Cherkasova Tatiana

2017-01-01

Full Text Available An urgent issue for power plants operating on solid fuels (coal is the issue of utilization or use of accumulated production waste - ash and slag materials - in the related production. Ash-slag materials are classified as “waste”, usually grade 5; tens of millions of tons of them being pro-duced annually in the Kemerovo region, which threatens the ecology of the region. At the same time, ash and slag is a very promising raw material. The use of this material as a base for the final product allows us to signifi-cantly expand the possibilities of using coal. The most widespread is the system of ash and slag involving in construction or as a replacement for sand in road construction, or as an additive to building mixtures. However, there are both industrially valuable and environmentally dangerous ele-ments in ash-slag materials. Ash-slag materials can be considered as inde-pendent ore deposits located on the surface and requiring the costs of their extraction.

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash

Directory of Open Access Journals (Sweden)

Martin Ernesto Kalaw

2016-07-01

Full Text Available Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC, which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1 their technical properties are comparable if not better; (2 they can be produced from industrial wastes; and (3 within reasonable constraints, their production requires less energy and emits significantly less CO2. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA and coal bottom ash (CBA, and rice hull ash (RHA. The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF for elemental and X-ray diffraction (XRD for mineralogical composition. The raw materials’ thermal stability and loss on ignition (LOI were determined using thermogravimetric analysis (TGA and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR

Low severity conversion of activated coal

Energy Technology Data Exchange (ETDEWEB)

Hirschon, A.S.; Ross, D.S.

1990-01-01

The results suggest that coal contains regions with structural components significantly reactive under the hydrothermal environment. Although the specific mechanism for this process remains to be developed, this activity is reminiscent of findings in studies of accelerated maturation of oil shale, where hydrothermal treatment (hydrous pyrolysis) leads to the production of petroleum hydrocarbons. In line with what has been seen in the oil shale work, the pretreatment-generated hydrocarbons and phenols appear to represent a further or more complete maturation of some fraction of the organic material within the coal. These observations could have an impact in two areas. The first is in the area of coal structure, where immature, reactive regions have not been included in the structures considered at present. The second area of interest is the more practical one of conversions to coal liquids and pyrolytic tars. It seems clear that the hydrothermal pretreatment changes the coal in some manner that favorably affects the product quality substantially and, as in the CO/water liquefaction case, favorably affects the yields. The conversions of coals of lower rank, i.e., less mature coals, could particularly benefit in terms of both product quality and product quantity. The second portion of this project also shows important benefits to coal conversion technology. It deals with synthesizing catalysts designed to cleave the weak links in the coal structure and then linking these catalysts with the pretreatment methods in Task 2. The results show that highly dispersed catalysts can effectively be used to increase the yields of soluble material. An important aspect of highly dispersed catalysts are that they can effectively catalyze coal conversion even in poor liquefaction solvents, thus making them very attractive in processes such as coprocessing where inexpensive liquefaction media such as resids are used.

Evaluation of heavy metal leaching from coal ash-versus conventional concrete monoliths and debris.

Science.gov (United States)

Gwenzi, Willis; Mupatsi, Nyarai M

2016-03-01

Application of coal ash in construction materials is constrained by the potential risk of heavy metal leaching. Limited information is available on the comparative heavy metal leaching from coal ash-versus conventional concrete. The current study compared total and leached heavy metal concentrations in unbound coal ash, cement and sand; and investigated the effect of initial leachant pH on heavy metal leaching from coal-ash versus conventional concrete monoliths and their debris. Total Pb, Mn and Zn in coal ash were lower than or similar to that of other materials, while Cu and Fe showed the opposite trend. Leached concentrations of Zn, Pb, Mn, Cu and Fe in unbound coal ash, its concrete and debris were comparable and in some cases even lower than that for conventional concrete. In all cases, leached concentrations accounted for just leaching data showed that leaching was dominated by diffusion. Overall, the risk of Zn, Pb, Mn, Cu and Fe leaching from coal ash and its concrete was minimal and comparable to that of conventional concrete, a finding in contrast to widely held public perceptions and earlier results reported in other regions such as India. In the current study the coal ash, and its concrete and debris had highly alkaline pH indicative of high acid neutralizing and pH buffering capacity, which account for the stabilization of Zn, Pb, Mn, Cu and Fe. Based on the low risk of Zn, Pb, Mn, Cu and Fe leaching from the coal ash imply that such coal ash can be incorporated in construction materials such as concrete without adverse impacts on public and environmental health from these constituents. Copyright © 2015 Elsevier Ltd. All rights reserved.

Promotive study on preparation of basis for foreign coal import. Study on coal renaissance

Energy Technology Data Exchange (ETDEWEB)

Muraoka, Yoji [Japan Economic Research Institute, Tokyo

1988-09-16

This is an interim report on the coal renaissance study carried out in 1987 as a part of the Promotive Study on Preparation of Basis for Foreign Coal Import. The background and ideology of coal renaissance, future aspect of demand for coal, problems pertaining to the expansion of application, and a proposal for the expansion of coal usage are described in order. The role of coal expected as an alternate fuel for petroleum, development of new application fields for coal, conversion to coal, contribution of Japan to the stablization of international coal supply are outlined. Coal renaissance aims, based on technology, at stimulation of coal demand, change in the image of coal, and the utilization of the accumulated abundant knowhow. The aspect of coal demand in 2000, solution and current status of various restricting factors relating to the use of coal in general industry, and the remaining problems are discussed. 6 figures, 10 tables.

Study on standard coal preparation plant for coking coal in Jharia Coalfield

Energy Technology Data Exchange (ETDEWEB)

Winiewski, J; Sarkar, G G

1975-10-01

The proposed standardization of coal preparation plant will be based on three standard types of crushing station, a standard jig washery or cyclone washery, and three standard types of slurry water treatment section. Some large installations, and some existing washeries after modification, may incorporate heavy media baths for coarse coal and jigs for slack coal, where coal is easy or moderately easy to wash. Flow sheets are given for the standard types of crushing plant, washery, and slurry water circuit. The storage of raw coal and saleable products is briefly discussed.

PAH volatilization following application of coal-tar-based pavement sealant

Science.gov (United States)

Van Metre, Peter C.; Majewski, Michael S.; Mahler, Barbara J.; Foreman, William T.; Braun, Christopher L.; Wilson, Jennifer T.; Burbank, Teresa L.

2012-01-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, have recently been identified as a source of volatile PAHs to the atmosphere. We tracked the volatilization of PAHs for 1 year after application of a coal-tar-based pavement sealant by measuring gas-phase PAH concentrations above the pavement surface and solid-phase PAH concentrations in sealant scraped from the surface. Gas-phase concentrations at two heights (0.03 and 1.28 m) and wind speed were used to estimate volatilization flux. The sum of the concentrations of eight frequently detected PAHs (ΣPAH8) in the 0.03-m sample 1.6 h after application (297,000 ng m-3) was about 5000 times greater than that previously reported for the same height above unsealed parking lots (66 ng m-3). Flux at 1.6 h after application was estimated at 45,000 μg m-2 h-1 and decreased rapidly during the 45 days after application to 160 μg m-2 h-1. Loss of PAHs from the adhered sealant also was rapid, with about a 50% decrease in solid-phase ΣPAH8 concentration over the 45 days after application. There was general agreement, given the uncertainties, in the estimated mass of ΣPAH8 lost to the atmosphere on the basis of air sampling (2–3 g m-2) and adhered sealant sampling (6 g m-2) during the first 16 days after application, translating to a loss to the atmosphere of one-quarter to one-half of the PAHs in the sealcoat product. Combining the estimated mass of ΣPAH8 released to the atmosphere with a national-use estimate of coal-tar-based sealant suggests that PAH emissions from new coal-tar-based sealcoat applications each year (~1000 Mg) are larger than annual vehicle emissions of PAHs for the United States.

Plant growth response in experimental soilless mixes prepared from coal combustion products and organic waste materials

Energy Technology Data Exchange (ETDEWEB)

Bardhan, S.; Watson, M.; Dick, W.A. [Ohio State University, Wooster, OH (United States)

2008-07-15

Large quantities of organic materials such as animal manures, yard trimmings, and biosolids are produced each year. Beneficial use options for them are often limited, and composting has been proposed as a way to better manage these organic materials. Similarly, burning of coal created 125 million tons of coal combustion products (CCP) in the United States in 2006. An estimated 53 million tons of CCP were reused, whereas the remainder was deposited in landfills. By combining CCP and composted organic materials (COM), we were able to create soilless plant growth mixes with physicochemical conditions that can support excellent plant growth. An additional benefit is the conservation of natural raw materials, such as peat, which is generally used for making soilless mixes. Experimental mixes were formulated by combining CCP and COM at ratios ranging from 2:8 to 8:2 (vol/vol), respectively. Water content at saturation for the created mixes was 63% to 72%, whereas for the commercial control, it was 77%. pH values for the best performing mixes ranged between 5.9 and 6.8. Electrical conductivity and concentrations of required plant nutrient were also within plant growth recommendations for container media. Significantly (P < 0.0001) higher plant biomass growth (7%-130%) was observed in the experimental mixes compared with a commercial mix. No additional fertilizers were provided during the experiment, and reduced fertilization costs can thus accrue as an added benefit to the grower. In summary, combining CCP and COM, derived from source materials often viewed as wastes, can create highly productive plant growth mixes.

Assessment of inhalation risk due to radioactivity released from coal-based thermal power plant

International Nuclear Information System (INIS)

Sahu, S.K.; Pandit, G.G.; Shukla, V.K.; Puranik, V.D.; Kushwaha, H.S.

2006-01-01

In India, the coal based thermal power plants have been the major source of power generation in the past and would continue for decades to come. As the coal contains naturally occurring primordial radionuclides the burning of pulverized coal to produce energy for generation of electricity in thermal power plants will result in the emission of a variety of natural radioactive elements into the environment in the vicinity of thermal power plants. In this paper we have used two different methods for characterization of uncertainty in inhalation risk to the general public around 10 Kms radius in the neighborhood of a coal-fired thermal power plant. (author)

Quantifying greenhouse gas emissions from coal fires using airborne and ground-based methods

Science.gov (United States)

Engle, Mark A.; Radke, Lawrence F.; Heffern, Edward L.; O'Keefe, Jennifer M.K.; Smeltzer, Charles; Hower, James C.; Hower, Judith M.; Prakash, Anupma; Kolker, Allan; Eatwell, Robert J.; ter Schure, Arnout; Queen, Gerald; Aggen, Kerry L.; Stracher, Glenn B.; Henke, Kevin R.; Olea, Ricardo A.; Román-Colón, Yomayara

2011-01-01

Coal fires occur in all coal-bearing regions of the world and number, conservatively, in the thousands. These fires emit a variety of compounds including greenhouse gases. However, the magnitude of the contribution of combustion gases from coal fires to the environment is highly uncertain, because adequate data and methods for assessing emissions are lacking. This study demonstrates the ability to estimate CO2 and CH4 emissions for the Welch Ranch coal fire, Powder River Basin, Wyoming, USA, using two independent methods: (a) heat flux calculated from aerial thermal infrared imaging (3.7–4.4 t d−1 of CO2 equivalent emissions) and (b) direct, ground-based measurements (7.3–9.5 t d−1 of CO2 equivalent emissions). Both approaches offer the potential for conducting inventories of coal fires to assess their gas emissions and to evaluate and prioritize fires for mitigation.

Annotated bibliography of coal in the Caribbean region. [Lignite

Energy Technology Data Exchange (ETDEWEB)

Orndorff, R.C.

1985-01-01

The purpose of preparing this annotated bibliography was to compile information on coal localities for the Caribbean region used for preparation of a coal map of the region. Also, it serves as a brief reference list of publications for future coal studies in the Caribbean region. It is in no way an exhaustive study or complete listing of coal literature for the Caribbean. All the material was gathered from published literature with the exception of information from Cuba which was supplied from a study by Gordon Wood of the US Geological Survey, Branch of Coal Resources. Following the classification system of the US Geological Survey (Wood and others, 1983), the term coal resources has been used in this report for reference to general estimates of coal quantities even though authors of the material being annotated may have used the term coal reserves in a similar denotation. The literature ranges from 1857 to 1981. The countries listed include Colombia, Mexico, Venezuela, Cuba, the Dominican Republic, Haiti, Jamaica, Puerto Rico, and the countries of Central America.

Gas Emission Prediction Model of Coal Mine Based on CSBP Algorithm

Directory of Open Access Journals (Sweden)

Xiong Yan

2016-01-01

Full Text Available In view of the nonlinear characteristics of gas emission in a coal working face, a prediction method is proposed based on cuckoo search algorithm optimized BP neural network (CSBP. In the CSBP algorithm, the cuckoo search is adopted to optimize weight and threshold parameters of BP network, and obtains the global optimal solutions. Furthermore, the twelve main affecting factors of the gas emission in the coal working face are taken as input vectors of CSBP algorithm, the gas emission is acted as output vector, and then the prediction model of BP neural network with optimal parameters is established. The results show that the CSBP algorithm has batter generalization ability and higher prediction accuracy, and can be utilized effectively in the prediction of coal mine gas emission.

Coal petrology of coal seams from the Leao-Butia Coalfield, Lower Permian of the Parana Basin, Brazil - Implications for coal facies interpretations

Energy Technology Data Exchange (ETDEWEB)

Silva, M.B. [Laboratorio de Oceanografia Geologica, Departamento de Geociencias, Fundacao Universidade Federal do Rio Grande, FURG, Av. Italia km 08, Campus Carreiros, 96201-900, Rio Grande, RS (Brazil); Kalkreuth, W.; Holz, M. [Instituto de Geociencias, UFRGS, Av. Bento Goncalves, 9500 91501-970 Porto Alegre, RS (Brazil)

2008-02-01

In the Leao-Butia Coalfield, Rio Grande do Sul the coal seams occur in the Rio Bonito Formation, Guata Group, Tubarao Supergroup of the Parana Basin, Brazil and are of Permian (Artinskian-Kungurian) age. This study is the first detailed investigation on the coal petrographic characterization of the coal-bearing sequence in relation to the depositional settings of the precursor mires, both in terms of whole seam characterization and in-seam variations. The study is based on the analyses of nine coal seams (I2, CI, L4, L3, L2, L1, S3, S2, S1), which were selected from core of borehole D-193, Leao-Butia and represent the entire coal-bearing sequence. The interpretation of coal facies and depositional environment is based on lithotype, maceral and microlithotype analyses using different facies-critical petrographic indices, which were displayed in coal facies diagrams. The seams are characterized by the predominance of dull lithotypes (dull, banded dull). The dullness of the coal is attributed to relatively high mineral matter, inertinite and liptinite contents. The petrographic composition is dominated by vitrinite (28-70 vol.% mmf) and inertinite (> 30 vol.% mmf) groups. Liptinite contents range from 7 to 30 vol.% (mmf) and mineral matter from 4-30 vol.%. Microlithotypes associations are dominated by vitrite, duroclarite, carbominerite and inertite. It is suggested that the observed vertical variations in petrographic characteristics (lithotypes, microlithotypes, macerals, vitrinite reflectance) were controlled by groundwater level fluctuations in the ancient mires due to different accommodation/peat accumulation rates. Correlation of the borehole strata with the general sequence-stratigraphical setting suggests that the alluvial fan system and the coal-bearing mudstone succession are linked to a late transgressive systems tract of sequence 2. Based on average compositional values obtained from coal facies diagrams, a deposition in a limno-telmatic to limnic coal

Catalytic coal liquefaction with treated solvent and SRC recycle

Science.gov (United States)

Garg, Diwakar; Givens, Edwin N.; Schweighardt, Frank K.

1986-01-01

A process for the solvent refining of coal to distillable, pentane soluble products using a dephenolated and denitrogenated recycle solvent and a recycled, pentane-insoluble, solvent-refined coal material, which process provides enhanced oil-make in the conversion of coal.

Analysis and forecast of railway coal transportation volume based on BP neural network combined forecasting model

Science.gov (United States)

Xu, Yongbin; Xie, Haihong; Wu, Liuyi

2018-05-01

The share of coal transportation in the total railway freight volume is about 50%. As is widely acknowledged, coal industry is vulnerable to the economic situation and national policies. Coal transportation volume fluctuates significantly under the new economic normal. Grasp the overall development trend of railway coal transportation market, have important reference and guidance significance to the railway and coal industry decision-making. By analyzing the economic indicators and policy implications, this paper expounds the trend of the coal transportation volume, and further combines the economic indicators with the high correlation with the coal transportation volume with the traditional traffic prediction model to establish a combined forecasting model based on the back propagation neural network. The error of the prediction results is tested, which proves that the method has higher accuracy and has practical application.

Nuclear assay of coal. Volume 6. Mass flow devices for coal handling. Final report

International Nuclear Information System (INIS)

Gozani, T.; Elias, E.; Bevan, R.

1980-04-01

The mass of coal entering the boiler per unit time is an essential parameter for determining the total rate of heat input. The mass flow rate of coal on a conveyor belt is generally determined as a product of the instantaneous mass of material on a short section of the belt and the belt velocity. Belt loading could be measured by conventional transducers incorporating mechanical or electromechanical weighers or by gamma-ray attenuation gauge. This report reviews the state of the art in mass flow devices for coal handling. The various methods are compared and commented upon. Special design issues are discussed relative to incorporating a mass flow measuring device in a Continuous On-Line Nuclear Analysis of Coal (CONAC) system

A Study of Coal Miners’ Safety Psychological Elements Based on Questionnaire Survey

Directory of Open Access Journals (Sweden)

Li Zeng-bo

2016-01-01

Full Text Available During the production process, the instability of safety psychological elements of coal miners contributes to unsafe behaviors that may result in fatal accident. To search the dominant psychological elements, three types of unsafe psychology, comprising 18 unsafe psychological elements, are obtained by theoretical analysis and site survey. Then, an assessment model is established, and a matched questionnaire is applied to two large modern coal mines in Inner Mongolia Autonomous Region. Based on questionnaire survey results and analytic hierarchy process (AHP, assessment judgment matrixes are constructed, effect weight is calculated, and consistency check is conducted. The analysis results show that safety psychology elements of defective type are the dominant elements that trigger unsafe behaviors of coal miners.

Coal - 96

International Nuclear Information System (INIS)

Sparre, C.

1996-09-01

The report deals mainly with coal consumption, but also gives some information about technology, environmental aspects and markets. Data have been collected by questionnaires or via telephone. The use of steam coal for heating was 0.8 Mtons (down 20% from 1994). Cogeneration plants were the main users. Taxes and environmental reasons cause a reduction of the coal use that will probably continue the next years. Use of steam coal in industry has been constant at a level of 0.7 Mtons. The import of metallurgical coal rests constant at a level of 1.6 Mtons. 1.2 Mtons of coke was produced, and 0.3 Mtons imported. The PFBC-plant at Vaertan, Stockholm used 0.13 Mtons of coal, while some coal fired power plants have been converted to peat and wood fuels. The average price of steam coal imported to Sweden in 1995 was 333 SEK/ton, 6% higher than in 1994. The contract prices for delivery 1996 are about the same as at the end of 1995. All cogeneration plants have some sort of SO 2 removal system, mostly wet-dry. The largest plant, at Vaesteraas, has recently invested in a SCR system for NO x removal. Most other plants are using low NO x burners or SNCR systems, based on ammonia or urea, which reduce the emissions 50 - 70%. Some statistic about the world coal market is also given in the report

The marriage of gas turbines and coal

International Nuclear Information System (INIS)

Bajura, R.A.; Webb, H.A.

1991-01-01

This paper reports on developing gas turbine systems that can use coal or a coal-based fuel ensures that the United States will have cost-effective environmentally sound options for supplying future power generation needs. Power generation systems that marry coal or a coal-based fuel to a gas turbine? Some matchmakers would consider this an unlikely marriage. Historically, most gas turbines have been operated only on premium fuels, primarily natural gas or distillate oil. The perceived problems from using coal or coal-based fuels in turbines are: Erosion and deposition: Coal ash particles in the hot combustion gases passing through the expander turbine could erode or deposit on the turbine blades. Corrosion: Coal combustion will release alkali compounds form the coal ash. Alkali in the hot gases passing through the expander turbine can cause corrosion of high-temperature metallic surfaces. Emissions: coal contains higher levels of ash, fuel-bound sulfur and nitrogen compounds, and trace contaminants than premium fuels. Meeting stringent environmental regulations for particulates, sulfur dioxide (SO 2 ), nitrogen oxides (NO x ), and trace contaminants will be difficult. Economics: Coal-based systems are expensive to build. The difference in price between coal and premium fuels must be large enough to justify the higher capital cost

Australian black coal statistics 1991

Energy Technology Data Exchange (ETDEWEB)

1992-01-01

This third edition of Australian black coal statistics covers anthracite, bituminous and subbituminous coals. It includes maps and figures on resources and coal fields and statistics (mainly based on the calendar year 1991) on coal demand and supply, production, employment and productivity in Australian coal mines, exports, prices and ports, and domestic consumption. A listing of coal producers by state is included. A final section presents key statistics on international world trade in 1991. 54 tabs.

Boiler briquette coal versus raw coal: Part I--Stack gas emissions.

Science.gov (United States)

Ge, S; Bai, Z; Liu, W; Zhu, T; Wang, T; Qing, S; Zhang, J

2001-04-01

Stack gas emissions were characterized for a steam-generating boiler commonly used in China. The boiler was tested when fired with a newly formulated boiler briquette coal (BB-coal) and when fired with conventional raw coal (R-coal). The stack gas emissions were analyzed to determine emission rates and emission factors and to develop chemical source profiles. A dilution source sampling system was used to collect PM on both Teflon membrane filters and quartz fiber filters. The Teflon filters were analyzed gravimetrically for PM10 and PM2.5 mass concentrations and by X-ray fluorescence (XRF) for trace elements. The quartz fiber filters were analyzed for organic carbon (OC) and elemental carbon (EC) using a thermal/optical reflectance technique. Sulfur dioxide was measured using the standard wet chemistry method. Carbon monoxide was measured using an Orsat combustion analyzer. The emission rates of the R-coal combustion (in kg/hr), determined using the measured stack gas concentrations and the stack gas emission rates, were 0.74 for PM10, 0.38 for PM2.5, 20.7 for SO2, and 6.8 for CO, while those of the BB-coal combustion were 0.95 for PM10, 0.30 for PM2.5, 7.5 for SO2, and 5.3 for CO. The fuel-mass-based emission factors (in g/kg) of the R-coal, determined using the emission rates and the fuel burn rates, were 1.68 for PM10, 0.87 for PM2.5, 46.7 for SO2, and 15 for CO, while those of the BB-coal were 2.51 for PM10, 0.79 for PM2.5, 19.9 for SO2, and 14 for CO. The task-based emission factors (in g/ton steam generated) of the R-coal, determined using the fuel-mass-based emission factors and the coal/steam conversion factors, were 0.23 for PM10, 0.12 for PM2.5, 6.4 for SO2, and 2.0 for CO, while those of the BB-coal were 0.30 for PM10, 0.094 for PM2.5, 2.4 for SO2, and 1.7 for CO. PM10 and PM2.5 elemental compositions are also presented for both types of coal tested in the study.

Boiler Briquette Coal versus Raw Coal: Part I-Stack Gas Emissions.

Science.gov (United States)

Ge, Su; Bai, Zhipeng; Liu, Weili; Zhu, Tan; Wang, Tongjian; Qing, Sheng; Zhang, Junfeng

2001-04-01

Stack gas emissions were characterized for a steam-generating boiler commonly used in China. The boiler was tested when fired with a newly formulated boiler briquette coal (BB-coal) and when fired with conventional raw coal (R-coal). The stack gas emissions were analyzed to determine emission rates and emission factors and to develop chemical source profiles. A dilution source sampling system was used to collect PM on both Teflon membrane filters and quartz fiber filters. The Teflon filters were analyzed gravimetrically for PM 10 and PM 2.5 mass concentrations and by X-ray fluorescence (XRF) for trace elements. The quartz fiber filters were analyzed for organic carbon (OC) and elemental carbon (EC) using a thermal/optical reflectance technique. Sulfur dioxide was measured using the standard wet chemistry method. Carbon monoxide was measured using an Orsat combustion analyzer. The emission rates of the R-coal combustion (in kg/hr), determined using the measured stack gas concentrations and the stack gas emission rates, were 0.74 for PM 10 , 0.38 for PM 25 , 20.7 for SO 2 , and 6.8 for CO, while those of the BB-coal combustion were 0.95 for PM 10 , 0.30 for PM 2 5 , 7.5 for SO 2 , and 5.3 for CO. The fuel-mass-based emission factors (in g/kg) of the R-coal, determined using the emission rates and the fuel burn rates, were 1.68 for PM 10 , 0.87 for PM 25 , 46.7 for SO 2 , and 15 for CO, while those of the BB-coal were 2.51 for PM 10 , 0.79 for PM 2.5 , 19.9 for SO 2 , and 14 for CO. The task-based emission factors (in g/ton steam generated) of the R-coal, determined using the fuel-mass-based emission factors and the coal/ steam conversion factors, were 0.23 for PM 10 , 0.12 for PM 2.5 , 6.4 for SO 2 , and 2.0 for CO, while those of the BB-coal were 0.30 for PM 10 , 0.094 for PM 2.5 , 2.4 for SO 2 , and 1.7 for CO. PM 10 and PM 2.5 elemental compositions are also presented for both types of coal tested in the study.

Self-scrubbing coal

International Nuclear Information System (INIS)

Kindig, J.K.

1992-01-01

More than 502 million tons - 65 percent of all coal shipped to utilities in 1990 - were above 1.2 pounds of sulfur dioxide per million Btu. Most of the coal, even though cleaned in conventional coal preparation plants, still does not meet the emission limitation the Clean Air Act Amendments mandate for the year 2000. To cope with this fact, most utilities plan to switch to low sulfur (western U.S. or Central Appalachian) coal or install scrubbers. Both solutions have serous drawbacks. Switching puts local miners out of work and weakens the economy in the utility's service territory. Scrubbing requires a major capital expenditure by the utility. Scrubbers also increase the operating complexity and costs of the generating station and produce yet another environmental problem, scrubber sludge. Employing three new cost-effective technologies developed by Customer Coals International (CCl), most non-compliance coals east of the Mississippi River can be brought into year-2000 compliance. The compliance approach employed, depends upon the characteristics of the raw coal. Three types of raw coal are differentiated, based upon the amount of organic sulfur in the coals and the ease (or difficultly) of liberating the pyrite. They are: Low organic sulfur content and pyrite that liberates easily. Moderate organic sulfur content and pyrite that liberates easily. High organic sulfur content or the pyrite liberates with difficulty. In this paper examples of each type of raw coal are presented below, and the compliance approach employed for each is described. The names of the beneficiated coal products produced from each type of raw coal give above are: Carefree Coal, Self-Scrubbing Coal and Dry-Scrubbing Coal

Characterization of a coal tailing deposit for zero waste mine in the Brazilian coal field of Santa Catarina

International Nuclear Information System (INIS)

Amaral Filho, J.R.; Schneider, I.A.H.; Tubino, R.M.C.; Brum de, I.A.S.; Miltzarek, G.; Sampaio, C.H.

2010-01-01

Coal tailings deposits in Brazil are occupying large areas of land while also generating acid mine drainage (AMD) that includes heavy metals. This paper described an analytical study of a typical coal tailings deposit. The study objective was to separate low density, intermediate density, and high density fractions for future reuse. Particle size analysis, disymmetric studies, X-ray diffraction, and tests conducted to determine ash, total sulphur, and acid bases were conducted in order to characterize the coal tailings samples. Results of the study demonstrated a size distribution of 67 percent coarse, 14 percent fine, and 19 percent ultra-fine particles. The gravimetric concentration method was used to recover 34.2 percent of the total deposit for future energy use. Approximately 9.2 percent of the remaining deposit was a pyrite concentrate. The acid generating potential of the remaining materials was reduced by approximately 60 percent. 9 refs., 1 tab., 2 figs.

The Palynological Investigation of Carboniferous Coal Measures In the Amasra Basin

Directory of Open Access Journals (Sweden)

Yaşar ERGÖNÜL

1960-12-01

Full Text Available In the field of modern coal geology and palaeontology systematic studies of isolated fossil spores constitute a relatively new phase of paleobotanical research. In this paper, the content of the Megaspores in the paleophytogenetic material has been investigated. All the coal samples of this study were collected from the coal borings executed by the M. T. A. Institute in the Amasra district dining the year 1959-1960. For the maceration of the Amasra coal samples, Schultze's and Zetzsche's methods were applied. Our new Megaspore species described here are based on the morphological study. These species are referred to spore genera as defined by Potonie and Kremp (1954 and Bhardwaj (1955. As a result of this palynological study, one new genus and 14 new species have been discovered, described and stratigraphically evaluated.

Digital coal mine integrated automation system based on Controlnet

Energy Technology Data Exchange (ETDEWEB)

Jin-yun Chen; Shen Zhang; Wei-ran Zuo [China University of Mining and Technology, Xuzhou (China). School of Chemical Engineering and Technology

2007-06-15

A three-layer model for digital communication in a mine is proposed. Two basic platforms are discussed: a uniform transmission network and a uniform data warehouse. An actual, ControlNet based, transmission network platform suitable for the Jining No.3 coal mine in China is presented. This network is an information superhighway intended to integrate all existing and new automation subsystems. Its standard interface can be used with future subsystems. The network, data structure and management decision-making all employ this uniform hardware and software. This effectively avoids the problems of system and information islands seen in traditional mine-automation systems. The construction of the network provides a stable foundation for digital communication in the Jining No.3 coal mine. 9 refs., 5 figs.

Integrated coal preparation

International Nuclear Information System (INIS)

Buchanan, D.J.; Jones, T.F.

1992-01-01

Perceptions of quality have changed over the years. The attributes of a certain coal (its rank, slagging propensity, ash content etc) are traditionally referred to as its quality. However, the subject of this paper is quality in a much wider sense: quality as fitness for purpose: and all that such a wide definition entails. British Standard BS 5750 (ISO 9000) Quality Systems defines a systems approach to quality, and includes both the supplier of raw materials and the final customer within this boundary. Coal preparation starts at the production face. The greater the proportion of dirt in run-of-mine product the greater the challenge in satisfying the customer's needs. Significant advances have been made in minimizing mined dirt. For example, the sue of vertical steering on longwall faces improves productivity and quality. Unfortunately modern mining methods produce large quantities of fines, despite efforts to reduce them at the point of production and during transportation to the surface. Coal preparation also produces further fines. It has been estimated that fine coal costs 2.5 times as much to clean as large coal, and the costs of handing wet fine coal product will inflate this estimate. Handling considerations rightly concern our customers and are part of the wider meaning of quality. In this paper the authors address some novel solutions to the challenge posed by fines

Environmental control implications of generating electric power from coal. Appendix B. Assessment of status of technology for solvent refining of coal. 1977 technology status report

Energy Technology Data Exchange (ETDEWEB)

None

1977-12-01

This report reviews the technology and environmental impacts of the solvent refined coal process to produce clean solid fuel (SRC-I). Information on SRC-I pilot plant operation, process design, and economics is presented. A bibliography of current available literature in this technology area, divided into fourteen categories with abstracts of the references, is appended. The history, current operations, and future plans for the SRC pilot plants at Fort Lewis and Wilsonville are reviewed. Process data generated at these pilot plants for various coals are used as a basis for a conceptual commercial plant design with a capacity to process 20,000 tons per day (TPD) of prepared coal. Block flow diagrams, material balances, an energy balance, and a list of raw materials for the plant are also provided. Capital cost estimates for a 20,000 TPD coal feed plant derived from four prior economic studies range from $706 million to $1093 million in 1976 dollars. The annual net operating cost is estimated at $238.6 million (1976 dollars) and the average product cost at $2.71/MM Btu based on utility financing (equity 25:debt 75) with $25/ton as the delivered price of the dry coal. The report also discusses special technical considerations associated with some of the process operations and major equipment items and enumerates technical risks associated with the commercialization of the SRC-I process.

E-commerce finally finds the coal industry

Energy Technology Data Exchange (ETDEWEB)

Hudson, M.

2000-12-01

In the last few months, new web sites have come online which are not only showcase for coal mining products and equipment but also act as sales platforms. A large set of sites deal with the purchase of coal and other raw materials. Most of them offer 24-hour news updates, a coal library and a reference section to help with financing, insurance and transportation of purchased coal. Another group focuses on the sale of equipment. Short writeups are given of 18 web sites. 1 photo.

Report on results for fiscal 1997 on development of coal liquefaction technology . Development of liquefaction base technology (studies on development and internationalization of environmentally benign coal liquefaction technology); 1997 nendo sekitan ekika gijutsu seika hokokusho. Ekika kiban gijutsu no kaihatsu (kankyo chowagata sekitan ekika gijutsu no kaihatsu oyobi kokusaika kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The research objective is the development of environmentally benign coal liquefaction technology and the studies on internationalization of coal liquefaction technology. Implemented for the former are (1) research on improvement and rationalization of liquefaction process and (2) research on advancement of liquefaction base technology. In (1), studies were made on in-oil preprocessing technology and scale suppressing measures for the purpose of obtaining reform/high grade of coal, and on improvement of liquefied oil collecting ratio, sophistication of coal slurry and attainment of light oil/high grade from liquefied crude oil for the purpose of optimizing liquefaction reactive conditions and improving a solvent. In (2), in developing high activity/high dispersion type new catalysts, catalytic sufurization behavior and activity manifestation mechanism were explored, as were iron hydroxide based iron ore properties and liquefaction reactive characteristics. The initial reactive characteristics of liquefaction for example were investigated for the purpose of collecting basic data for expanding kinds of coal. In order to attain the latter objective of the research, a feasibility study of liquefaction location was conducted, as were the investigation including sampling of iron ore for catalytic material and the investigation of coal gasification technology. After the completion of the Australian brown coal liquefaction project, the development of the coal liquefaction technology commenced in fiscal 1994 produced a number of useful records and ended in 1997. (NEDO)

Upgraded Coal Interest Group -- A vision for coal-based power in 1999 and beyond

International Nuclear Information System (INIS)

Hughes, E.; Battista, J.; Stopek, D.; Akers, D.

1999-01-01

The US is at a critical junction. Global competition is now a reality for a large number of US businesses and, ultimately, almost all US businesses will compete to one degree or another in the global marketplace. Under these circumstances, maintaining and improving the standard of living of US citizens requires a plentiful supply of low-cost electric energy to reduce the cost of providing goods and services both in the US an abroad. At the same time, segments of the public demand increased environmental restrictions on the utility industry. If the electric utility industry is to successfully respond to the goals of reducing electricity costs, maintaining reliability, and reducing emissions, fuels technology research is critical. For coal-fired units, fuel cost typically represents from 60--70% of operating costs. Reducing fuel cost, reduces operating costs. This can provide revenue that could be used to finance emissions control systems or advanced type of boilers resulting from post-combustion research. At the same time, improving coal quality reduces emissions from existing boilers without the need for substantial capital investment by the utility. If quality improvements can be accomplished with little or no increase in fuel costs, an immediate improvement in emissions can be achieved without an increase in electricity costs. All of this is directly dependent on continued and expanded levels of research on coal with the cooperation and partnership between government and industry. The paper describes enhanced fuel technologies (use of waste coal, coal water slurries, biomass/composite fuels, improved dewatering technologies, precombustion control of HAPs, dry cleaning technologies, and international coal characterization) and enhanced emission control technologies

The future of coal-fired generation

Energy Technology Data Exchange (ETDEWEB)

White, G. [Sherritt International Corp., Calgary, AB (Canada)

2004-07-01

The 3 features that will ensure coal's place as a primary energy source are its affordability, availability and its abundance. Coal reserves represent more than 200 years of supply. Graphs depicting coal consumption in North America, Central and South America, Western Europe, Easter Europe, Middle East, Africa, and Asia show that coal use is expected to grow 1.5 per cent annually. Asia is the greatest consumer of coal, while the consumption of coal in Eastern Europe is steadily declining. About half of the electricity supply in the United States will continue to be generated by coal and non-electrical utilization is also expected to grow. Emerging technologies that are promoting efficiency of coal utilization include combustion technology, clean coal technology, conversion technology and emissions technology. These technologies also address environmental concerns regarding coal combustion, such as removal of carbon dioxide through sequestration and reduction in nitrogen oxides, sulphur dioxide and particulates. Mercury mitigation technologies are also being developed. It was noted that the use of coal is mitigated by other available supply such as nuclear, natural gas and hydro which provide the base load generation. Renewable energy supply can meet up to 20 per cent of the base load, while coal can fill be gap between base load and peak loads. It was noted that the use of coal in direct industrial processes allows for synergies such as syngas for bitumen upgrading, coal as a chemical feedstock with electricity as a by-product, combined heat and power and cogeneration. tabs., figs.

New approach to brown coal pricing using internal rate of return methodology

International Nuclear Information System (INIS)

Bejbl, Jan; Bemš, Julius; Králík, Tomáš; Starý, Oldřich; Vastl, Jaromír

2014-01-01

Highlights: • We showed that brown coal is the substitute for black coal only at the time of the investment decision. • We compiled the model used in a calculation of the economically justified price for the productive and extractive component. • The resulting economically justified price is on a par with the current black coal price. • The proposed methodological approach is applicable to solve similar tasks not only in the energy sector. - Abstract: Brown coal is one of the dominant local strategic raw materials in Europe, used, to a large extent, in the power-generating industry. The current situation, where the price of gas and electricity precludes the efficient use of gas sources, leads to the extraction of older sources, chiefly brown coal ones. In tandem with a turning away from nuclear power, brown coal is experiencing a renaissance and the issue of brown coal price setting is, and will be, relevant. This paper deals with a proposal of a new method for determining the base price, consisting of defining the reference fuel chain for electricity and heat production based on brown coal. It builds on the notion that the degree of risk of the involved parties should be reflected in the modified amount of revenue per capital invested. The resulting price is then an economically justified price which encourages a respect for the specific features of the market in question and set the base price of the commodity in a way that is acceptable for both the extractive and the productive components of the fuel chain

Life-cycle assessment for coal-based methanol production in China

DEFF Research Database (Denmark)

Li, Changhang; Bai, Hongtao; Lu, Yuanye

2018-01-01

using the coal coking technology than by producing methanol using the coal gasification technology, especially in terms of acidification, global warming, and photochemical oxidation. In particular, significantly less environmental harm in terms of climate change and radiation is caused by the coal...... coking technology than by the coal gasification technology. Different sub-processes clearly make different contributions to environmental harm. The results indicated that the methanol production process, heating, and desalination are the main sources of environmental harm for both the coal gasification...... technology and coal coking technology. Importantly, the public engineering process rather than the methanol production process itself was found to determine emissions for the different methanol production methods....

Current status of U.S. coal utilization and non-fuel uses of fossil fuels

International Nuclear Information System (INIS)

Song, C.S.; Schobert, H.; Scaroni, A.W.

1997-01-01

An understanding of the current situation is important for projecting the future direction of coal utilization. The world's annual consumption of coal in 1995 was 5104.01 million short tons (MST, 1 short ton = 0.907 metric ton). Coal plays a very important role in the US energy supply; US coal production in 1995 totaled 1033 MST, including 611.1 MST of bituminous coal, 328.4 MST of subbituminous coal, 86.1 MST of lignite, and 4.1 MST of anthracite. US coal consumption totaled 940.6 MST, with 88.1% in electric utilities, 3.5% in coke plants, 7.8% for other industrial uses, and only 0.6% in the residential and commercial sectors. The amount of fossil resources used for non-fuel purposes accounted for 8.4% of the total annual consumption in 1995. Non-fuel uses of fossil fuels particularly coal may become more important in the future. The demonstrated coal reserves in the world are large enough for consumption for over 220 years at the 1995 level, while proven oil reserves are only about 40 times the world's 1995 consumption level. Coal has several positive attributes when considered as a feedstock for aromatic chemicals, specialty chemicals, and carbon-based materials. Existing nonfuel uses of coals include (1) high temperature carbonization of bituminous and subbituminous coals to make metallurgical coke; (2) gasification of coal to make synthesis gases and other chemicals; (3) use of coal in manufacturing other materials such as activated carbons, carbon molecular sieves (CMS) and production of phosphorus (phosphoric acid); (4) the use of coal tars from carbonization and gasification for making aromatic and phenolic chemicals; (5) the use of coal tar pitch for making carbon fibers and activated carbon fibers; and (6) other non-fuel products derived from coal including combustion by-products. Coal may become more important both as an energy source and as the source of chemical feedstocks in the 21st century

Weathering behaviour of overburden-coal ash blending in relation to overburden management for acid mine drainage prevention in coal surface mine

International Nuclear Information System (INIS)

Gautama, R.S.; Kusuma, G.J.; Lestari, I.; Anggana, R.P.

2010-01-01

Potentially acid forming (PAF) materials are encapsulated with non-acid forming materials (NAF) in order to prevent acid mine drainage (AMD) in surface coal mines. NAF compaction techniques with fly and bottom ashes from coal-fired power plants are used in mines with limited amounts of NAF materials. This study investigated the weathering behaviour of blended overburden and coal combustion ash in laboratory conditions. Free draining column leach tests were conducted on different blending schemes. The weathering process was simulated by spraying the samples with de-ionized water once per day. The leachates were then analyzed using X-ray diffraction and fluorescence analyses in order to identify the mineral composition of the samples over a 14 week period. Results of the study indicated that the weathering process plays a significant role in controlling infiltration rates, and may increase the capability of capping materials to prevent infiltration into PAF materials. Fly- and bottom-ash additions improved the performance of the encapsulation materials. 3 refs., 4 tabs., 2 figs.

International Coal Report's coal year 1991

Energy Technology Data Exchange (ETDEWEB)

McCloskey, G [ed.

1991-05-31

Following introductory articles on factors affecting trade in coal and developments in the freight market, tables are given for coal exports and coal imports for major countries worldwide for 1989 and 1990. Figures are also included for coal consumption in Canada and the Eastern bloc,, power station consumption in Japan, coal supply and demand in the UK, electric utility coal consumption and stocks in the USA, coal production in Australia, Canada and USA by state, and world hard coal production. A final section gives electricity production and hard coal deliveries in the EEC, sales of imported and local coal and world production of pig iron and steel.

Geological storage of carbon dioxide in the coal seams: from material to the reservoir

International Nuclear Information System (INIS)

Nikoosokhan, S.

2012-01-01

CO 2 emissions into the atmosphere are recognized to have a significant effect on global warming. Geological storage of CO 2 is widely regarded as an essential approach to reduce the impact of such emissions on the environment. Moreover, injecting carbon dioxide in coal bed methane reservoirs facilitates the recovery of the methane naturally present, a process known as enhanced coal bed methane recovery (ECBM). But the swelling of the coal matrix induced by the preferential adsorption by coal of carbon dioxide over the methane in place leads to a closure of the cleat system (a set of small natural fractures) of the reservoir and therefore to a loss of injectivity. This PhD thesis is dedicated to a study of how this injectivity evolves in presence of fluids. We derive two poro-mechanical dual-porosity models for a coal bed reservoir saturated by a pure fluid. The resulting constitutive equations enable to better understand and model the link between the injectivity of a coal seam and the adsorption-induced swelling of coal. For both models, the pore space of the reservoir is considered to be divided into the macroporous cleats and the pores of the coal matrix. The two models differ by how adsorption of fluid is taken into account: the first model is restricted to surface adsorption, while the second model can be applied for adsorption in a medium with a generic pore size distribution and thus in a microporous medium such as coal, in which adsorption mostly occurs by micropore filling. The latter model is calibrated on two coals with different sorption and swelling properties. We then perform simulations at various scales (Representative Elementary Volume, coal sample, coal seam). In particular, we validate our model on experimental data of adsorption-induced variations of permeability of coal. We also perform simulations of seams from which methane would be produced (CBM) or of methane-free seams into which CO 2 would be injected. We study the effect of various

Comparison Analysis of Coal Biodesulfurization and Coal's Pyrite Bioleaching with Acidithiobacillus ferrooxidans

Science.gov (United States)

Hong, Fen-Fen; He, Huan; Liu, Jin-Yan; Tao, Xiu-Xiang; Zheng, Lei; Zhao, Yi-Dong

2013-01-01

Acidithiobacillus ferrooxidans (A. ferrooxidans) was applied in coal biodesulfurization and coal's pyrite bioleaching. The result showed that A. ferrooxidans had significantly promoted the biodesulfurization of coal and bioleaching of coal's pyrite. After 16 days of processing, the total sulfur removal rate of coal was 50.6%, and among them the removal of pyritic sulfur was up to 69.9%. On the contrary, after 12 days of processing, the coal's pyrite bioleaching rate was 72.0%. SEM micrographs showed that the major pyrite forms in coal were massive and veinlets. It seems that the bacteria took priority to remove the massive pyrite. The sulfur relative contents analysis from XANES showed that the elemental sulfur (28.32%) and jarosite (18.99%) were accumulated in the biotreated residual coal. However, XRD and XANES spectra of residual pyrite indicated that the sulfur components were mainly composed of pyrite (49.34%) and elemental sulfur (50.72%) but no other sulfur contents were detected. Based on the present results, we speculated that the pyrite forms in coal might affect sulfur biooxidation process. PMID:24288464

Combustion and environmental performance of clean coal end products

Energy Technology Data Exchange (ETDEWEB)

Skodras, G.; Sakellaropoulos, G. [Centre for Research and Technology, Hellas, Ptolemaidas-Kozanis, Ptolemaida (Greece). Inst. for Solid Fuel Technolgy and Applications]|[Aristotle Univ. of Thessaloniki, Thessaloniki (Greece). Dept. of Chemical Engineering, Chemical Process Engineering Lab]|[Chemical Process Engineering Research Inst., Thessaloniki (Greece). Lab. of Solid Fuels and Environment; Someus, E. [Thermal Desorption Technology Group (Greece); Grammelis, P.; Amarantos, P.S. [Centre for Research and Technology, Hellas, Ptolemaidas-Kozanis, Ptolemaida (Greece). Inst. for Solid Fuel Technolgy and Applications; Palladas, A.; Basinas, P.; Natas, P.; Prokopidou, M.; Diamantopoulou, I.; Sakellaropoulos, G. [Aristotle Univ. of Thessaloniki, Thessaloniki (Greece). Dept. of Chemical Engineering, Chemical Process Engineering Lab

2006-07-01

Clean and affordable power production is needed in order to achieve sustainable economic development. This paper focused on clean coal technologies in which coal-fired power plants are used in conjunction with large amounts of renewable energy sources to offer a high level of process safety and long term management of all residual operation streams. Thermal Desorption Recycle-Reduce-Reuse Technology (TDT-3R) was described as being a promising solid fuel pretreatment process for clean energy production up to 300 MWe capacities. TDT-3R is based on low temperature carbonisation fuel pre-treatment principles, which produce cleansed anthracite type fuels from coal and other carbonaceous material such as biomass and organic wastes. The combustion efficiency of such clean coals and the environmental performance of the TDT-3R process were investigated in this study via pilot scale tests of clean fuel production. Tests included flue gas emissions monitoring, raw fuel and product characterisation and thermogravimetric tests, polychlorinated dibenzo-p-dioxins and dibenzo-furans, and heavy metals analyses, and toxicity tests. Raw material included coal and biomass, such as willow, straw and demolition wood. The fuels were heated in a rotary kiln operating at 550 degrees C under slightly vacuum conditions. Clean coals were tested either alone or in conjunction with biomass fuels in a pilot scale combustion facility at Dresden, Germany. The clean coal samples were shown to have higher fixed carbon and ash content and lower volatiles compared to the respective raw coal samples. The major advantage of the TDT-3R process is the production of fuels with much lower pollutants content. Low nitrogen, sulphur, chlorine and heavy metal contents result in produced fuels that have excellent environmental performance, allow boiler operation in higher temperatures and overall better efficiency. Moreover, the use of clean fuels reduces deposition problems in the combustion chamber due to the

The identification of unusual microscopic features in coal and their derived chars: Influence on coal fluidized bed combustion

Energy Technology Data Exchange (ETDEWEB)

Valentim, B. [Centro de Geologia da Universidade do Porto, Rua do Campo Alegre 687, 4169-007 Porto (Portugal); Lemos de Sousa, M.J. [Centro de Geologia da Universidade do Porto, Praca de Gomes Teixeira, 4099-002 Porto (Portugal); Abelha, P.; Boavida, D.; Gulyurtlu, I. [Departamento de Engenharia Energetica e Controlo Ambiental (DEECA), Instituto Nacional de Engenharia, Tecnologia e Inovacao (INETI), Estrada do Paco do Lumiar, 22, Edif. J, 1649-038, Lisboa (Portugal)

2006-06-06

During the petrographic study of seven feed coals from different origins, it was found that these coals presented microfeatures such as: material size, shape, weathering, thermally affected particles and contamination. After devolatilization under fluidized bed conditions, some chars presented the consequences of the above mentioned microfeatures, i.e., unreacted coal, unswelled particles, coatings and microstratification. Since the amounts of the microfeatures observed were low (less than 1%), the present study is essentially observational/descriptional. However, it seems very likely, from the observations that were made, that the occurrence of one or more of these microfeatures in coal, depending on their kind and abundance, may have significant effect on the coal devolatilization. (author)

Monte Carlo simulation of moderator and reflector in coal analyzer based on a D-T neutron generator.

Science.gov (United States)

Shan, Qing; Chu, Shengnan; Jia, Wenbao

2015-11-01

Coal is one of the most popular fuels in the world. The use of coal not only produces carbon dioxide, but also contributes to the environmental pollution by heavy metals. In prompt gamma-ray neutron activation analysis (PGNAA)-based coal analyzer, the characteristic gamma rays of C and O are mainly induced by fast neutrons, whereas thermal neutrons can be used to induce the characteristic gamma rays of H, Si, and heavy metals. Therefore, appropriate thermal and fast neutrons are beneficial in improving the measurement accuracy of heavy metals, and ensure that the measurement accuracy of main elements meets the requirements of the industry. Once the required yield of the deuterium-tritium (d-T) neutron generator is determined, appropriate thermal and fast neutrons can be obtained by optimizing the neutron source term. In this article, the Monte Carlo N-Particle (MCNP) Transport Code and Evaluated Nuclear Data File (ENDF) database are used to optimize the neutron source term in PGNAA-based coal analyzer, including the material and shape of the moderator and neutron reflector. The optimized targets include two points: (1) the ratio of the thermal to fast neutron is 1:1 and (2) the total neutron flux from the optimized neutron source in the sample increases at least 100% when compared with the initial one. The simulation results show that, the total neutron flux in the sample increases 102%, 102%, 85%, 72%, and 62% with Pb, Bi, Nb, W, and Be reflectors, respectively. Maximum optimization of the targets is achieved when the moderator is a 3-cm-thick lead layer coupled with a 3-cm-thick high-density polyethylene (HDPE) layer, and the neutron reflector is a 27-cm-thick hemispherical lead layer. Copyright © 2015 Elsevier Ltd. All rights reserved.

Coal-tar-based sealcoated pavement: A major PAH source to urban stream sediments

International Nuclear Information System (INIS)

Witter, Amy E.; Nguyen, Minh H.; Baidar, Sunil; Sak, Peter B.

2014-01-01

We used land-use analysis, PAH concentrations and assemblages, and multivariate statistics to identify sediment PAH sources in a small (∼1303 km 2 ) urbanizing watershed located in South-Central, Pennsylvania, USA. A geographic information system (GIS) was employed to quantify land-use features that may serve as PAH sources. Urban PAH concentrations were three times higher than rural levels, and were significantly and highly correlated with combined residential/commercial/industrial land use. Principal components analysis (PCA) was used to group sediments with similar PAH assemblages, and correlation analysis compared PAH sediment assemblages to common PAH sources. The strongest correlations were observed between rural sediments (n = 7) and coke-oven emissions sources (r = 0.69–0.78, n = 5), and between urban sediments (n = 22) and coal-tar-based sealcoat dust (r = 0.94, n = 47) suggesting that coal-tar-based sealcoat is an important urban PAH source in this watershed linked to residential and commercial/industrial land use. -- Highlights: • Total PAH concentrations were measured at 35 sites along an urbanizing land-use gradient. • PAH concentrations increased with increasing urban land-use. • Urban land-use metrics were measured at three spatial scales using GIS. • PAH assemblages indicate coal-tar-based sealcoat is a major urban PAH source. • PAH assemblages indicate coke-oven emissions are an important rural PAH source. -- Coal-tar-based sealcoated pavement is a major PAH source to urban freshwater stream sediments in south-central Pennsylvania, USA

The development of coal-based technologies for Department of Defense facilities: Phase 1 final report. Volume 1: Technical report

Energy Technology Data Exchange (ETDEWEB)

Miller, B.G.; Morrison, J.L.; Pisupati, S.V. [Pennsylvania State Univ., University Park, PA (United States). Energy and Fuels Research Center] [and others

1997-01-31

The first phase of a three-phase project investigating the development of coal-based technologies for Department of Defense facilities has been completed. The objectives of the project are to: decrease DOD`s dependence on foreign oil and increase its use of coal; promote public and private sector deployment of technologies for utilizing coal-based fuels in oil-designed combustion equipment; and provide a continuing environment for research and development of coal-based fuel technologies for small-scale applications at a time when market conditions in the US are not favorable for the introduction of coal-fired equipment in the commercial and industrial capacity ranges. The Phase 1 activities were focused on developing clean, coal-based combustion technologies for the utilization of both micronized coal-water mixtures (MCWMs) and dry, micronized coal (DMC) in fuel oil-designed industrial boilers. The specific objective in Phase 1 was to deliver fully engineered retrofit options for a fuel oil-designed watertube boiler located on a DOD installation to fire either MCWM or DMC. This was achieved through a project consisting of fundamental, pilot-sale, and demonstration-scale activities investigating coal beneficiation and preparation, and MCWM and DMC combustion performance. In addition, detailed engineering designs and an economic analysis were conducted for a boiler located at the Naval Surface Warfare Center, near Crane, Indiana. Results are reported on MCWM and DMC combustion performance evaluation; engineering design; and cost/economic analysis.

Australian coal mine methane emissions mitigation potential using a Stirling engine-based CHP system

International Nuclear Information System (INIS)

Meybodi, Mehdi Aghaei; Behnia, Masud

2013-01-01

Methane, a major contributor to global warming, is a greenhouse gas emitted from coal mines. Abundance of coal mines and consequently a considerable amount of methane emission requires drastic measures to mitigate harmful effects of coal mining on the environment. One of the commonly adopted methods is to use emitted methane to fuel power generation systems; however, instability of fuel sources hinders the development of systems using conventional prime movers. To address this, application of Stirling engines may be considered. Here, we develop a techno-economic methodology for conducting an optimisation-based feasibility study on the application of Stirling engines as the prime movers of coal mine CHP systems from an economic and an environmental point of view. To examine the impact of environmental policies on the economics of the system, the two commonly implemented ones (i.e. a carbon tax and emissions trading scheme) are considered. The methodology was applied to a local coal mine. The results indicate that incorporating the modelled system not only leads to a substantial reduction in greenhouse gas emissions, but also to improved economics. Further, due to the heavy economic burden, the carbon tax scheme creates great incentive for coal mine industry to address the methane emissions. -- Highlights: •We study the application of Stirling engines in coal mine CHP systems. •We develop a thermo-economic approach based on the net present worth analysis. •We examine the impact of a carbon tax and ETS on the economics of the system. •The modeled system leads to a substantial reduction in greenhouse gas emissions. •Carbon tax provides a greater incentive to address the methane emissions

Use of wet FGD material for revegetation of an abandoned acidic coal refuse pile

International Nuclear Information System (INIS)

Mafi, S.; Stehouwer, R.C.

1996-01-01

Wet FGD material has a neutralizing potential of 15% CaCO 3 . These properties may make it a beneficial amendment for revegetation of hyper-acidic coal refuse. In greenhouse and field experiments, coal refuse (pH = 2.5) was amended with wet FGD (300, 500, and 700 tons/acre). Amendment with FGD was as effective as agricultural lime (AL) in increasing refuse pH and decreasing soluble Al and Fe. Addition of compost to the FGD further increased pH and decreased soluble Al and Fe. Downward transport of Ca was greater with FGD than AL, but FGD did not increase leachate concentrations of S. Amendment with FGD increased refuse, leachate and plant tissue concentrations of B. Other trace elements were not increased by FGD. In the greenhouse, plant growth was similar with AL and FGD except during the first three months when AL produced more growth than FGD. The initial growth suppression by FGD was likely due to high soluble salts, and possibly by high B concentrations. During the first year of the field experiment plant growth was greater with FGD than with AL. In both the field and greenhouse experiments compost increased plant growth when combined with FGD. These experiments show revegetation of toxic coal refuse and improvement in drainage water quality is possible by amendment with FGD. Revegetation success will be improved by combined amendment with FGD and compost

Modeling Creep-Fatigue-Environment Interactions in Steam Turbine Rotor Materials for Advanced Ultra-supercritical Coal Power Plants

Energy Technology Data Exchange (ETDEWEB)

Shen, Chen [General Electric Global Research, Niskayuna, NY (United States)

2014-04-01

The goal of this project is to model creep-fatigue-environment interactions in steam turbine rotor materials for advanced ultra-supercritical (A-USC) coal power Alloy 282 plants, to develop and demonstrate computational algorithms for alloy property predictions, and to determine and model key mechanisms that contribute to the damages caused by creep-fatigue-environment interactions.

Coal geology and assessment of coal resources and reserves in the Powder River Basin, Wyoming and Montana

Science.gov (United States)

Luppens, James A.; Scott, David C.

2015-01-01

This report presents the final results of the first assessment of both coal resources and reserves for all significant coal beds in the entire Powder River Basin, northeastern Wyoming and southeastern Montana. The basin covers about 19,500 square miles, exclusive of the part of the basin within the Crow and Northern Cheyenne Indian Reservations in Montana. The Powder River Basin, which contains the largest resources of low-sulfur, low-ash, subbituminous coal in the United States, is the single most important coal basin in the United States. The U.S. Geological Survey used a geology-based assessment methodology to estimate an original coal resource of about 1.16 trillion short tons for 47 coal beds in the Powder River Basin; in-place (remaining) resources are about 1.15 trillion short tons. This is the first time that all beds were mapped individually over the entire basin. A total of 162 billion short tons of recoverable coal resources (coal reserve base) are estimated at a 10:1 stripping ratio or less. An estimated 25 billion short tons of that coal reserve base met the definition of reserves, which are resources that can be economically produced at or below the current sales price at the time of the evaluation. The total underground coal resource in coal beds 10–20 feet thick is estimated at 304 billion short tons.

Model of environmental life cycle assessment for coal mining operations.

Science.gov (United States)

Burchart-Korol, Dorota; Fugiel, Agata; Czaplicka-Kolarz, Krystyna; Turek, Marian

2016-08-15

This paper presents a novel approach to environmental assessment of coal mining operations, which enables assessment of the factors that are both directly and indirectly affecting the environment and are associated with the production of raw materials and energy used in processes. The primary novelty of the paper is the development of a computational environmental life cycle assessment (LCA) model for coal mining operations and the application of the model for coal mining operations in Poland. The LCA model enables the assessment of environmental indicators for all identified unit processes in hard coal mines with the life cycle approach. The proposed model enables the assessment of greenhouse gas emissions (GHGs) based on the IPCC method and the assessment of damage categories, such as human health, ecosystems and resources based on the ReCiPe method. The model enables the assessment of GHGs for hard coal mining operations in three time frames: 20, 100 and 500years. The model was used to evaluate the coal mines in Poland. It was demonstrated that the largest environmental impacts in damage categories were associated with the use of fossil fuels, methane emissions and the use of electricity, processing of wastes, heat, and steel supports. It was concluded that an environmental assessment of coal mining operations, apart from direct influence from processing waste, methane emissions and drainage water, should include the use of electricity, heat and steel, particularly for steel supports. Because the model allows the comparison of environmental impact assessment for various unit processes, it can be used for all hard coal mines, not only in Poland but also in the world. This development is an important step forward in the study of the impacts of fossil fuels on the environment with the potential to mitigate the impact of the coal industry on the environment. Copyright © 2016 Elsevier B.V. All rights reserved.

A guide to coal chute replacement

Energy Technology Data Exchange (ETDEWEB)

O' Neil, M. [Parramatta Group (United States)

2006-11-15

Good material flow can reduce coal yard maintenance and operational problems. A thorough inspection of the conveyor system can reveal some of the obvious signs of underperforming material transfer points in a power generation facility. The author gives 10 reasons why plant owners may need to look at an engineered transfer solution to improve flow, particularly of Powder River Basin coal. Items are ordered starting from auditing the inside of the chute walls, moving to liners, then to general buildup and outside spillage. 3 photos.

Externalities of biomass based electricity production compared to power generation from coal in the Netherlands

International Nuclear Information System (INIS)

Faaij, A.; Meuleman, B.

1997-12-01

Externalities of electricity production from biomass and coal are investigated and compared for the Dutch context. Effects on economic activity and employment are investigated by means of Input/Output and multiplier tables. Valuations of damage from emissions to air are based on generic data from other studies. In addition, external costs are estimated for nitrogen leaching and for the use of agrochemicals for energy crop production. The average private costs for biomass and coal based power generation are projected to be 68 and 38 mECU/kWh respectively in the year 2005. It is assumed that biomass production takes place on fallow land. Coal mining is excluded from the analysis. If the quantified external damages and benefits are included the cost range for bio-electricity is 53-70 mECU/kWh and 45-72 mECU/kWh for coal. Indirect economic effects (increment of Gross Domestic Product) and the difference in CO2 emissions are the most important distinguishing factors between coal and biomass in economic terms. Damage costs of other emissions to air (NOx, SO2, dust and CO) are of the same order of magnitude for both coal and biomass (coal mining excluded). In this analysis environmental impacts of energy farming are compared mainly to fallow land focused on the use of fertilizers and agrochemicals. The related damage costs appear to be low but should be considered as a preliminary estimate only. The quantitative outcomes should not be considered as the external costs of the two fuel cycles studied. Many impacts have not been valued and large uncertainties persist e.g. with respect to the costs of climate change and numerous dose response relations. More detailed analysis is required with respect to macro-economic impacts. The results serve as a first indication, but the outcomes plead for the support of bio-electricity production and/or taxation of coal based power generation. 88 refs

INTERPRETATION OF COAL POTENTION USING GROUND PENETRATING RADAR (GPR METHOD

Directory of Open Access Journals (Sweden)

Rohmatul Wahidah

2018-01-01

Full Text Available Coal exposure founded at Klatak Kebo Ireng village in Besuki Tulungagung precisely in the vicinity of the river. Energy needs is increasing so the coal used for one of alternative energy source that can be used by society. This study was conducted to determine of the potential distribution coal modeling on geological structure. Identification of coal structure is using Ground Penetrating Radar (GPR 2005 it conducted because this method is more suitable for shallow of surveys. The location for taking data is around the river that showed to exposure. There are 5th lines of taken data with length about 50 until 100 meters. Data processing was done using of software Future series 2005. The data displayed with software in the color pattern to obtain based on the constant of dielectric and conductivity. The results of interpretation study are the data indicates that there is a coal on the overall trajectory. Only in 2nd track contain little of coal. The Coal layers are appear in processing the results of data is thickness about 6 at the top. In the area of study also found the cavity (cavity area which contained of several tracks. On the bottom of the track there is a pattern of coal reddish of yellow color which indicates that material contains of minerals.

Investigation on characterization of Ereen coal deposit

Directory of Open Access Journals (Sweden)

S. Jargalmaa

2016-03-01

Full Text Available The Ereen coal deposit is located 360 km west from Ulaanbaatar and 95 km from Bulgan town. The coal reserve of this deposit is approximately 345.2 million tons. The Ereen coal is used directly for the Erdenet power plant for producing of electricity and heat. The utilization of this coal for gas and liquid product using gasification and pyrolysis is now being considered. The proximate and ultimate analysis show that the Ereen coal is low rank D mark hard coal, which corresponds to subbituminous coal. The SEM images of initial coal sample have compact solid pieces. The SEM image of carbonized and activated carbon samples are hard material with high developed macro porosity structure. The SEM images of hard residue after thermal dissolution in autoclave characterizes hard pieces with micro porous structure in comparison with activated carbon sample. The results of the thermal dissolution of Ereen coal in tetralin with constant weight ratio between coal and tetralin (1:1.8 at the 450ºC show that 38% of liquid product can be obtained by thermal decomposition of the COM (coal organic matter.Mongolian Journal of Chemistry 16 (42, 2015, 18-21

A synchrotron-based local computed tomography combined with data-constrained modelling approach for quantitative analysis of anthracite coal microstructure

International Nuclear Information System (INIS)

Chen, Wen Hao; Yang, Sam Y. S.; Xiao, Ti Qiao; Mayo, Sherry C.; Wang, Yu Dan; Wang, Hai Peng

2014-01-01

A quantitative local computed tomography combined with data-constrained modelling has been developed. The method could improve distinctly the spatial resolution and the composition resolution in a sample larger than the field of view, for quantitative characterization of three-dimensional distributions of material compositions and void. Quantifying three-dimensional spatial distributions of pores and material compositions in samples is a key materials characterization challenge, particularly in samples where compositions are distributed across a range of length scales, and where such compositions have similar X-ray absorption properties, such as in coal. Consequently, obtaining detailed information within sub-regions of a multi-length-scale sample by conventional approaches may not provide the resolution and level of detail one might desire. Herein, an approach for quantitative high-definition determination of material compositions from X-ray local computed tomography combined with a data-constrained modelling method is proposed. The approach is capable of dramatically improving the spatial resolution and enabling finer details within a region of interest of a sample larger than the field of view to be revealed than by using conventional techniques. A coal sample containing distributions of porosity and several mineral compositions is employed to demonstrate the approach. The optimal experimental parameters are pre-analyzed. The quantitative results demonstrated that the approach can reveal significantly finer details of compositional distributions in the sample region of interest. The elevated spatial resolution is crucial for coal-bed methane reservoir evaluation and understanding the transformation of the minerals during coal processing. The method is generic and can be applied for three-dimensional compositional characterization of other materials

Technology assessment of various coal-fuel options

International Nuclear Information System (INIS)

Coenen, R.; Findling, B.; Klein-Vielhauer, S.; Nieke, E.; Paschen, H.; Tangen, H.; Wintzer, D.

1991-01-01

The technology assessment (TA) study of coal-based fuels presented in this report was performed for the Federal Ministry for Research and Technology. Its goal was to support decision-making of the Federal Ministry for Research and Technology in the field of coal conversion. Various technical options of coal liquefaction have been analyzed on the basis of hard coal as well as lignite -- direct liquefaction of coal (hydrogenation) and different possibilities of indirect liquefaction, that is the production of fuels (methanol, gasoline) by processing products of coal gasification. The TA study takes into consideration the entire technology chain from coal mining via coal conversion to the utilization of coal-based fuels in road transport. The analysis focuses on costs of the various options, overall economic effects, which include effects on employment and public budgets, and on environmental consequences compared to the use of liquid fuels derived from oil. Furthermore, requirements of infrastructure and other problems of the introduction of coal-based fuels as well as prospects for the export of technologies of direct and indirect coal liquefaction have been analyzed in the study. 14 figs., 10 tabs

BARZAS DEPOSIT SAPROPELITE COALS: PROSPECTS OF INTEGRATED DEVELOPMENT

Directory of Open Access Journals (Sweden)

L. V. Kuznetsova

2018-03-01

Full Text Available The urgency of the problem. Sapropelite coals of the Barzas deposit of Kuzbass are good raw materials for producing liquid fuel, lubricating oils, paraffin, etc. Apart from that, they are enriched with molybdenum, niobium, rubidium, yttrium and titanium. The content of these deposits is higher than the minimal content, which determines the industrial importance of coal as a source of ore raw materials. However, until now, the field is not being developed because of the economic inexpediency and the lack of a solution to the problem of recycling of incineration and semi-coking waste, which have high ash content and a large volume. The purpose of the study: to develop the concept of integrated development of the Barzas sapropelite coal deposit on the basis of creating efficient, environmentally friendly and low-waste production. Research methodology. The analysis of geological and mining conditions of the formation, which is called the Main, the results of its geochemical studies of existing technologies of mining and processing the high-ash solid fuels. The promising areas of their development were also considered. Cluster approach to the development of sapropelite coal deposits. Results. Coal mining at the sites with different geological conditions can be carried out with openly-underground mobile means of mechanization. The First mine field can be developed by the underground way on the development system called “Long poles along the strike”. This can be attained by means of the comprehensive mechanization of the Second mine field. Also, “Long poles along strike, take out the strips by the drop” are combined sections of a mechanized roof support with mobile means of cutting and transportation of coal – the Third mine field. The energy-chemical cluster of the Barzas deposit of sapropelite coals is a complex of the enterprises, which are technologically connected among them. They are concentrated on the same territory, which includes

Properties of sorbents from brown coal

Energy Technology Data Exchange (ETDEWEB)

Straka, P.; Buchtele, J. [Academy of Sciences of the Czech Republic, Prague (Czech Republic)

2000-07-01

The surface and sorptional properties of carbonaceous materials prepared from brown coal and their relation to minerals content and coal bulk density as technologically important parameters of starting coal were described. Chars were prepared from brown coal of North Bohemian Brown Coal District and activated with CO{sub 2} in a large-scale laboratory unit. Their surface and sorptive properties were investigated. It was found that mineral matter/ash content favourably affects the mesoporosity development in chars/activated chars as the sorption capacity increased with increasing ash content in chars. No influence of ash content on the macroporosity was observed. With the activated chars, both the inner surface and sorption capacity showed the maximum in the burn-off range of 41-64%. Optimization of the process is discussed.

Fiscal 1994 survey of the base arrangement promotion for foreign coal import. Investigation on the trend of coal demand in Central and South American countries; 1994 nendo kaigaitan kiban seibi sokushin chosa. Chunanbei shokoku ni okeru sekitan jukyu doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Focusing on the present status and future of coal demand in Central/South American countries and the coal trade between Central/South American countries and the U.S., the paper described the present status and future of coal demand there and the effects on Japan. Export of Colombian coal will amount to approximately 30-35 million tons in 2000. Venezuelan coal 10-20 million tons. The U.S. imported good-quality general coal low in sulfur content, 3.08 tons from Columbia and 1.39 tons from Venezuela. Coal export from the U.S. to Central/South America was mostly of raw material coal, 5 million tons in 1993 and 5.39 million tons in 1994. General coal was 180,000 tons. The U.S. has no plans of increasing US coal export to Central/South America. But it is safely predicted that Columbia and Venezuela will increase coal export to Europe in the future. It will bring about decrease in export of US coal to Europe, which connects with increasing pressure for the coal trade amount of Japan. 21 figs., 47 tabs.

Prevention of trace and major element leaching from coal combustion products by hydrothermally-treated coal ash

Energy Technology Data Exchange (ETDEWEB)

Adnadjevic, B.; Popovic, A.; Mikasinovic, B. [University of Belgrade, Belgrade (Serbia). Dept. of Chemistry

2009-07-01

The most important structural components of coal ash obtained by coal combustion in 'Nikola Tesla A' power plant located near Belgrade (Serbia) are amorphous alumosilicate, alpha-quartz, and mullite. The phase composition of coal ash can be altered to obtain zeolite type NaA that crystallizes in a narrow crystallization field (SiO{sub 2}/Al{sub 2}O{sub 3}; Na{sub 2}O/SiO{sub 2}; H{sub 2}O/Na{sub 2}O ratios). Basic properties (crystallization degree, chemical composition, the energy of activation) of obtained zeolites were established. Coal ash extracts treated with obtained ion-exchange material showed that zeolites obtained from coal ash were able to reduce the amounts of iron, chromium, nickel, zinc, copper, lead, and manganese in ash extracts, thus proving its potential in preventing pollution from dump effluent waters.

Forecast and Prevention of Coal and Gas Outbursts in the Case of Application of a New Mining Method - Drilling of a Coal Pillar

Directory of Open Access Journals (Sweden)

Vlastimil Hudeček

2010-10-01

Full Text Available Coal and gas outbursts are one of risk factors accompanying the mining of coal in low seams in the Ostrava-Karviná Coalfield.At the use of the method of longwall mining, all coal reserves have not been mined out owing to tectonic faults. For mining outthe residual reserves, the application of a new mining method - drilling of a coal pillar was proposed.The method of mining of a coal seam utilizing long large diameter boreholes is verified in the Paskov Mine (company OKD, JSC –Czech Republic under conditions of rock mass with hazard of rock and gas outbursts in localities of residual pillars left in seams afterfinishing the mining operations performed with using the classical method of longwall working along the strike. [5]Forecast and preventive measures applied to the verification of the new method were based on previous experience withthe mining of seams with hazard of coal and gas outbursts. They accepted fully valid legislation, i.e. Ordinance of Ostrava RegionalMining Authority No. 3895/2002 and supplementary materials (Instructions and Guidelines. The proposed measures respectedthe character of the method being verified. [4]For all areas being mined, projects containing also chapters specifying the problems of ensuring the safety of mining worksand operation under conditions of hazard of coal and gas outbursts were prepared.In the contributions, basic proposals for the principles of coal and gas outburst forecast and prevention when applying the newmining method – drilling of a coal pillar are presented

Ultrafine coal classification using 150 mm gMax cyclone circuits

Energy Technology Data Exchange (ETDEWEB)

Honaker, R.Q.; Boaten, F.; Luttrell, G.H. [University of Kentucky, Lexington, KY (United States). Dept. of Mineral Engineering

2007-11-15

A two-stage classification circuit using 150 mm diameter gMax cyclones was installed and evaluated in a coal preparation plant in an effort to achieve a clean coal product without the use of froth flotation. Particle size separations of around 37 {mu}m were achieved while limiting ultrafine bypass to less than 10% in the circuit underflow stream. As a result, approximately 81% of the ash-bearing material in the circuit feed was rejected to the circuit overflow stream. The feed ash content was reduced from around 50% to values in the range of 22-30% in the circuit underflow stream with a mass recovery of about 30%. Further reductions in the coarse product ash content were limited due to the particle density effect and the remaining presence of a significant quantity of high-ash slime material in the coarse product. The typical D{sub 50} for the coal particles was 40 {mu} m while the estimated value for mineral matter was 17 {mu} m. Based on the findings of the study, the use of classification to recover a low-ash, coarse fraction in the feed of a fine coal circuit is limited by the density effect regardless of the ability to eliminate ultrafine bypass.

The calculation of the chemical exergies of coal-based fuels by using the higher heating values

International Nuclear Information System (INIS)

Bilgen, Selcuk; Kaygusuz, Kamil

2008-01-01

This paper demonstrates the application of exergy to gain a better understanding of coal properties, especially chemical exergy and specific chemical exergy. In this study, a BASIC computer program was used to calculation of the chemical exergies of the coal-based fuels. Calculations showed that the chemical composition of the coal influences strongly the values of the chemical exergy. The exergy value of a coal is closely related to the H:C and O:C ratios. High proportions of hydrogen and/or oxygen, compared to carbon, generally reduce the exergy value of the coal. High contents of the moisture and/or the ash cause to low values of the chemical exergy. The aim of this paper is to calculate the chemical exergy of coals by using equations given in the literature and to detect and to evaluate quantitatively the effect of irreversible phenomena increased the thermodynamic imperfection of the processes. In this paper, the calculated exergy values of the fuels will be useful for energy experts studied in the coal mining area and coal-fired powerplants

Possibility of chemical products from coal

Energy Technology Data Exchange (ETDEWEB)

Harris, G A; Sinnett, C E; Swift, H E

1982-01-01

An account of the SRC-II plant, which produces solvent refined coal (SRC), a liquid product. SRC is a raw material with potential as a new source of hydrocarbons. Topics discussed include the possibilities of its use as a petrochemical feedstock; derivatives and the amounts obtained; economic assessments and expected prices. The translator of this article puts forward the view that, due to the difficulty of obtaining the type of coal needed for SRC-II, the best policy for Japanese coal liquefaction is methanol synthesis.

Modern problems of deep processing of coal

International Nuclear Information System (INIS)

Ismagilov, Z.R.

2013-01-01

Present article is devoted to modern problems of deep processing of coal. The history and development of new Institute of Coal Chemistry and Material Sciences of Siberian Branch of Russian Academy of Science was described. The aims and purposes of new institute were discussed.

A Technique for Decreasing Reactivity of Coal Material to Suppress the Oxygen Absorption Process

OpenAIRE

Timofeeva, S. S.; Lugovtsova, Nataliya Yurievna; Gubanova, А. R.

2016-01-01

The paper describes the mechanisms of self-ignition formation in coal liable to spontaneous combustion, on the basis of experimental works performed to analyze heat and mass transfer in the coal-air system. A new approach was developed to the coal self-heating suppression and thermodynamic control of the oxidation process. The influence of coal moisture content and thermal behaviour of air in the cooling process was studied during moisture evaporation.

Combining Renewable Energy With Coal

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-09-01

There are various possibilities for incorporating biomass into coal-fuelled processes and a number of these are already being deployed commercially. Others are the focus of ongoing research and development. Biomass materials can vary widely, although the present report concentrates mainly on the use of woody biomass in the form of forest residues. Potentially, large amounts are available in some parts of the world. However, not all forested regions are very productive, and the degree of commercial exploitation varies considerably between individual countries. The level of wastage associated with timber production and associated downstream processing is frequently high and considerable quantities of potentially useful materials are often discarded. Overall, forest residues are a largely underexploited resource. Combining the use of biomass with coal can be beneficial, particularly from an environmental standpoint, although any such process may have its limitations or drawbacks. Each coal type and biomass feedstock has different characteristics although by combining the two, it may be possible to capitalise on the advantages of each, and minimise their individual disadvantages. An effective way is via cogasification, and useful operating experience has been achieved in a number of large-scale coal-fuelled gasification and IGCC plants. Cogasification can be the starting point for producing a range of products that include synthetic natural gas, chemicals, fertilisers and liquid transport fuels. It also has the potential to form the basis of systems that combine coal and biomass use with other renewable energy technologies to create clean, efficient energy-production systems. Thus, various hybrid energy concepts, some based on coal/biomass cogasification, have been proposed or are in the process of being developed or trialled. Some propose to add yet another element of renewable energy to the system, generally by incorporating electricity generated by intermittent

A comparison study on the deoxygenation of coal mine methane over coal gangue and coke under microwave heating conditions

International Nuclear Information System (INIS)

Guo, Xuan; Ren, Jun; Xie, Chuanjin; Lin, Jianying; Li, Zhong

2015-01-01

Highlights: • Microwave has great advantages of energy and time saving in CMM deoxygenation. • Microwave pretreatment results in graphitization of carbonaceous materials. • Coal gangue shows benefit in restricting CH 4 decomposition compared to coke. • Under optimal conditions, there is no residual oxygen and CH 4 is less than 2.2%. - Abstract: Microwave heating has great advantages in saving energy and time; in this study, it has been first successfully applied in the deoxidization process of coal mine methane (CMM), where carbon in coal gangue reacts with oxygen in CMM. Compared with traditional heating, microwave pretreatment resulted in rapid heating of coal gangue in CMM deoxygenation, which was attributable to the graphitization of carbonaceous materials. This prominent advantage of microwave heating can contribute to deoxygenation. In addition, deoxygenation effectiveness for both coke and coal gangue under microwave heating was investigated. It was discovered that coke acted as a catalyst to some extent to accelerate methane decomposition. However, this effect could be greatly restricted when coal gangue was used in the deoxygenation process because of its chemical inertness. Under optimal conditions (650 °C and 300 mL/min), there was no residual oxygen in the outlet gas, and methane loss was less than 2.2%

Coal Mine Health and Safety Regulation 2006 under the Coal Mine Health and Safety Act 2002

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-12-22

The aim of the Act is to secure the health, safety and welfare of people in connection with coal operations (which include all places of work where coal is mined and certain other places). The Regulation contains provisions about the following matters: (a) places of work to which the Act does not apply, (b) duties relating to health, welfare and safety at coal operations, including the following: (i) the nomination of the operator of a coal operation and the provision of health and safety information for incoming operators, (ii) the contents of health and safety management systems for coal operations, (iii) major hazards and the contents of major hazard management plans for coal operations, (iv) duties relating to contractors, (v) the contents of management structures and emergency management systems for coal operations, escape and rescue plans and fire fighting plans and high risk activities, (c) notifications, including (i) notification of incidents, (ii) inquiries, (iii) notification of other matters to the Chief Inspector), (d) aspects of safety at coal operations, including the following: (i) controlled materials, plants and practices, (ii) coal dust explosion prevention and suppression, (iii) ventilation at coal operations, (iv) escape from coal operations, (v) the operation of transport at coal operations, (vi) surveys and certified plans, (vii) employment at coal operations, (e) the licensing of certain activities, (f) competence standards, (g) the Coal Competence Board, (h) check inspectors, (i) exemptions from provisions of this Regulation, (j) the following miscellaneous matters concerning coal mine health and safety: (i) the keeping of records and reporting, (ii) penalties, the review of decisions by the Administrative Decisions Tribunal, fees and charges, consultation, information and other miscellaneous matters, (k) savings and transitional provisions.

Model of environmental life cycle assessment for coal mining operations

Energy Technology Data Exchange (ETDEWEB)

Burchart-Korol, Dorota, E-mail: dburchart@gig.eu; Fugiel, Agata, E-mail: afugiel@gig.eu; Czaplicka-Kolarz, Krystyna, E-mail: kczaplicka@gig.eu; Turek, Marian, E-mail: mturek@gig.eu

2016-08-15

This paper presents a novel approach to environmental assessment of coal mining operations, which enables assessment of the factors that are both directly and indirectly affecting the environment and are associated with the production of raw materials and energy used in processes. The primary novelty of the paper is the development of a computational environmental life cycle assessment (LCA) model for coal mining operations and the application of the model for coal mining operations in Poland. The LCA model enables the assessment of environmental indicators for all identified unit processes in hard coal mines with the life cycle approach. The proposed model enables the assessment of greenhouse gas emissions (GHGs) based on the IPCC method and the assessment of damage categories, such as human health, ecosystems and resources based on the ReCiPe method. The model enables the assessment of GHGs for hard coal mining operations in three time frames: 20, 100 and 500 years. The model was used to evaluate the coal mines in Poland. It was demonstrated that the largest environmental impacts in damage categories were associated with the use of fossil fuels, methane emissions and the use of electricity, processing of wastes, heat, and steel supports. It was concluded that an environmental assessment of coal mining operations, apart from direct influence from processing waste, methane emissions and drainage water, should include the use of electricity, heat and steel, particularly for steel supports. Because the model allows the comparison of environmental impact assessment for various unit processes, it can be used for all hard coal mines, not only in Poland but also in the world. This development is an important step forward in the study of the impacts of fossil fuels on the environment with the potential to mitigate the impact of the coal industry on the environment. - Highlights: • A computational LCA model for assessment of coal mining operations • Identification of

Model of environmental life cycle assessment for coal mining operations

International Nuclear Information System (INIS)

Burchart-Korol, Dorota; Fugiel, Agata; Czaplicka-Kolarz, Krystyna; Turek, Marian

2016-01-01

This paper presents a novel approach to environmental assessment of coal mining operations, which enables assessment of the factors that are both directly and indirectly affecting the environment and are associated with the production of raw materials and energy used in processes. The primary novelty of the paper is the development of a computational environmental life cycle assessment (LCA) model for coal mining operations and the application of the model for coal mining operations in Poland. The LCA model enables the assessment of environmental indicators for all identified unit processes in hard coal mines with the life cycle approach. The proposed model enables the assessment of greenhouse gas emissions (GHGs) based on the IPCC method and the assessment of damage categories, such as human health, ecosystems and resources based on the ReCiPe method. The model enables the assessment of GHGs for hard coal mining operations in three time frames: 20, 100 and 500 years. The model was used to evaluate the coal mines in Poland. It was demonstrated that the largest environmental impacts in damage categories were associated with the use of fossil fuels, methane emissions and the use of electricity, processing of wastes, heat, and steel supports. It was concluded that an environmental assessment of coal mining operations, apart from direct influence from processing waste, methane emissions and drainage water, should include the use of electricity, heat and steel, particularly for steel supports. Because the model allows the comparison of environmental impact assessment for various unit processes, it can be used for all hard coal mines, not only in Poland but also in the world. This development is an important step forward in the study of the impacts of fossil fuels on the environment with the potential to mitigate the impact of the coal industry on the environment. - Highlights: • A computational LCA model for assessment of coal mining operations • Identification of

Balance of natural radionuclides in the brown coal based power generation and harmlessness of the residues and side product utilization; Bilanz natuerlicher Radionuklide in der Braunkohleverstromung und Unbedenklichkeit bei der Verwendung von Rueckstaenden und Nebenprodukten

Energy Technology Data Exchange (ETDEWEB)

Schulz, Hartmut; Kunze, Christian; Hummrich, Holger [IAF-Radiooekologie GmbH, Radeberg (Germany)

2017-04-01

During brown coal combustion a partial enrichment of natural radionuclides occurs in different residues. Residues and side product from brown coal based power generation are used in different ways, for example filter ashes and gypsum from flue gas desulfurization facilities are used in the construction materials fabrication and slags for road construction. Detailed measurement and accounting of radionuclides in the mass throughputs in coal combustion power plants have shown that the utilized gypsum and filter ashes are harmless in radiologic aspects.

Clean coal technologies

International Nuclear Information System (INIS)

Aslanyan, G.S.

1993-01-01

According to the World Energy Council (WEC), at the beginning of the next century three main energy sources - coal, nuclear power and oil will have equal share in the world's total energy supply. This forecast is also valid for the USSR which possesses more than 40% of the world's coal resources and continuously increases its coal production (more than 700 million tons of coal are processed annually in the USSR). The stringent environmental regulations, coupled with the tendency to increase the use of coal are the reasons for developing different concepts for clean coal utilization. In this paper, the potential efficiency and environmental performance of different clean coal production cycles are considered, including technologies for coal clean-up at the pre-combustion stage, advanced clean combustion methods and flue gas cleaning systems. Integrated systems, such as combined gas-steam cycle and the pressurized fluidized bed boiler combined cycle, are also discussed. The Soviet National R and D program is studying new methods for coal utilization with high environmental performance. In this context, some basic research activities in the field of clean coal technology in the USSR are considered. Development of an efficient vortex combustor, a pressurized fluidized bed gasifier, advanced gas cleaning methods based on E-beam irradiation and plasma discharge, as well as new catalytic system, are are presented. In addition, implementation of technological innovations for retrofitting and re powering of existing power plants is discussed. (author)

Application of mine water leaching protocol on coal fly ash to assess leaching characteristics for suitability as a mine backfill material.

Science.gov (United States)

Madzivire, Godfrey; Ramasenya, Koena; Tlowana, Supi; Coetzee, Henk; Vadapalli, Viswanath R K

2018-04-16

Over the years, coal mining in the Mpumalanga Province of South Africa has negatively affected the environment by causing pollution of water resources, land subsidence and spontaneous coal combustion. Previous studies show that in-situ treatment of acid mine drainage (AMD) using coal fly ash (CFA) from local power stations was possible and sludge recovered out of such treatment can be used to backfill mines. In this article, the authors have attempted to understand the leaching characteristics of CFA when placed underground as a backfill material using the mine water leaching protocol (MWLP). The results show that the migration of contaminants between the coal fly ash and the AMD in the mine voids depends on the pH and quality of the mine water. While backfilling mine voids with CFA can neutralize and scavenge between 50% and 95% of certain environmentally sensitive elements from AMD such as Fe, Al, Zn, Cu, Ni, Co and Mn. At this moment, it is also important to point out that certain scavenged/removed contaminants from the AMD during initial phases of backfilling can be remobilized by the influx of acidic water into the mine voids. It has therefore been concluded that, while CFA can be used to backfill mine voids, the influx of fresh acidic mine water should be avoided to minimize the remobilization of trapped contaminants such as Fe, Al, Mn and As. However, the pozzolanic material resulting from the CFA-AMD interaction could prevent such influx.

Electrokinetics and flocculation studies of coal

Energy Technology Data Exchange (ETDEWEB)

Dhawan, N. [Punjab Engineering College, Chandigarh (India). Dept. of Metallurgical Engineering

2008-07-01

Coal from India contains 25-35 per cent ash content. This leads to high slag volume, lower calorific value and inferior coke. In order to remove ash content, coal is washed, however, it retains some water that makes it difficult to process. Mechanical dewatering is performed in which a large portion of solids is removed while the remainder remains in centrifuge. There is therefore a need to recover solids and water. This paper discussed the use of flocculation and electrokinetic studies such as the determination of the point of zero charge. The experimental studies considered factors such as turbidity, faster settling, and compactness. Flocculation is brought about by the action of high molecular weight materials such as polyelectrolytes, where the material physically forms a bridge between two or more particles, uniting the sold particles into a random, three-dimensional structure, which is loose and porous. This paper also described the materials and methods of the electrokinetic studies on coal samples. Materials that were described included nephelometer, zeta meter, and a flocculator. It was concluded that in selecting the best flocculant, the preference order should be turbidity; settling rate; dosage; and moisture content. 3 refs., 2 tabs., 8 figs.

The effect of petrographical composition of coals and bituminous sediments on the material and isotopic composition of dry natural gases from artificial recoalification reactions. 2

International Nuclear Information System (INIS)

Maass, I.; Huebner, H.; Nitzsche, H.-M.; Schuetze, H.; Zschiesche, M.

1975-01-01

Experimental results indicate that on the basis of the material and isotopic composition of natural gases conclusions can be drawn with regard to the character (humic or bituminous) of the parent rock. Thus, genetic relations assumed to exist between humic sediments (e.g. coal seams) and dry natural gases as well as bituminous rocks and wet natural gases are experimentally confirmed. In addition, from analyses of the materials approximate data can be derived on the degree of carbonization of coal or bituminous sediments in the main phase of gas separation. Furthermore, these analyses were used to elucidate the question whether authochthonous or allochthonous deposits are present. It could be shown that the maceral composition of coals and of the organo-petrographical inclusions in bituminous sediments determines the isotopic composition of methane in recoalification gases to a considerable degree. (author)

Application of the coal-mining waste in building ceramics production

Directory of Open Access Journals (Sweden)

Vaysman Yakov Iosifovich

Full Text Available In the process of construction ceramics production a substantial quantity of non-renewable natural resources - clays - are used. One of the ways of science development in building materials production is investigation of the possibility of regular materials production using technogenic waste. Application of coal-mining waste (technogenic raw material in charge composition for production of ceramic products provides rational use of fuel, contributes to implementation of resource saving technologies on construction materials production enterprises. Though science development on revealing new raw material sources should be conducted with account for safety, reliability, technical, ecological and economical sides of the problem, which is especially current. The article deals with the problem of coal-mining waste usage in building ceramics production instead of fresh primary component (clay, fluxes, thinning agents and combustible additives. The interdependence between the density and shrinkage of the ceramic products and the amount and quality of coal-mining waste in its composition was established. The optimal proportion of coal-mining waste and clay in building ceramics production was estimated.

Nanometre-sized pores in coal: Variations between coal basins and coal origin

Science.gov (United States)

Sakurovs, Richard; Koval, Lukas; Grigore, Mihaela; Sokolava, Anna; Ruppert, Leslie F.; Melnichenko, Yuri B.

2018-01-01

We have used small angle neutron scattering (SANS) to investigate the differences in methane and hexane penetration in pores in bituminous coal samples from the U.S., Canada, South Africa, and China, and maceral concentrates from Australian coals. This work is an extension of previous work that showed consistent differences between the extent of penetration by methane into 10–20 nm size pores in inertinite in bituminous coals from Australia, North America and Poland.In this study we have confirmed that there are differences in the response of inertinite to methane and hexane penetration in coals sourced from different coal basins. Inertinite in Permian Australian coals generally has relatively high numbers of pores in the 2.5–250 nm size range and the pores are highly penetrable by methane and hexane; coals sourced from Western Canada had similar penetrability to these Australian coals. However, the penetrability of methane and hexane into inertinite from the Australian Illawarra Coal Measures (also Permian) is substantially less than that of the other Australian coals; there are about 80% fewer 12 nm pores in Illawarra inertinite compared to the other Australian coals examined. The inertinite in coals sourced from South Africa and China had accessibility intermediate between the Illawarra coals and the other Australian coals.The extent of hexane penetration was 10–20% less than CD4 penetration into the same coal and this difference was most pronounced in the 5–50 nm pore size range. Hexane and methane penetrability into the coals showed similar trends with inertinite content.The observed variations in inertinite porosity between coals from different coal regions and coal basins may explain why previous studies differ in their observations of the relationships between gas sorption behavior, permeability, porosity, and maceral composition. These variations are not simply a demarcation between Northern and Southern Hemisphere coals.

Establishment of the carbon label mechanism of coal chemical products based oncarbon footprint

Directory of Open Access Journals (Sweden)

Wu Bishan

Full Text Available ABSTRACT After redefining the carbon footprint and carbon label, the paper analyzesthe significance of the carbon labels under the background of the low carbon economy development, and establishes the concept of model of the carbon labels mechanism to chemical products. At the same time, the paper quantitatively studies carbon label data sourceof three kinds of coal chemical industry power products, which are fromhaving not CCS technologies of supercritical boiler of coal, using CCS technologies of supercritical boiler of coal and adopting CCS and IGCC technologies to power generation in CCI. Based on the three kinds of differences, the paper puts forward of establishing the carbon labels mechanism of chemical products under the low carbon consumption.

On stream ash analysis of coal based on its natural gamma-ray activity

International Nuclear Information System (INIS)

Mathew, P.J.

1986-01-01

A novel method based on the natural gamma-ray activity of coal has been developed for the on-stream determination of ash. The accuracy of the method has been verified by measuring the natural gamma-ray activity and ash content of coal samples from a number of locations in New Zealand and Australia. The rms differences between % ash by ignition and % ash by the gamma-ray method ranged from 0.65% ash for coal samples from a Queensland mine to 1.6% ash for samples from a southern New South Wales mine. The rms errors include those to geovariance, and due to sampling and sample analysis by conventional means. The error in ash measurement by the gamma-ray method can therefore be reduced by substantially eliminating these errors. A prototype ash analyser was also developed and field-tested at the Huntly East mine. In a four-week test, the prototype gauge was used to determine the ash content of run-of-mine (rom) coal below 20% ash to within +- 1.7% ash. Laboratory studies of coal samples collected during the field test of the prototype gave an error of 0.8% ash for coal samples below 20% ash content. A higher error was observed in the field test compared with laboratory data, and the difference is attributed to errors in sampling from the conveyor belt

Fiscal 1996 survey of the base arrangement promotion for foreign coal import. Potentiality of the general coal market and the subjects; 1996 nendo kaigaitan yunyu kiban seibi sokushin chosa. Ippantan shijo no kanosei to sono kadai

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper examined thoughts of a method to determine the general coal price based on the hearing from coal users and coal suppliers and considered a potentiality of the general coal market in the Asia/Pacific area and the subjects. Electric power companies of Japan and coal companies of Australia which now own long-term contracts for general coal consider continuing the benchmark system also in the future. At New York Commodity Exchange and Sidney Futures Transaction, the listing of futures of general coal is studied, and Barlow Jonker opened a membership futures transaction system for general coal/PCI coal using internet. The paper investigated response of the industry circle to such moves of market trade/futures transaction of general coal. In the hearing, comments were mostly negative. It was pointed out that with the development of the spot market of coal, there is a possibility of the market trade form developing. In the future, the spot market is steadily developing, but it is thought that supplying to major general coal users in Japan, Korea and Taiwan will continue to be based mostly on long-term contracts. 42 refs., 38 figs., 26 tabs.

Raw Materials Market of China

Directory of Open Access Journals (Sweden)

Dmitry Alexandrovich Izotov

2013-12-01

Full Text Available Deficit of raw materials is becoming an important concern for the Chinese economy as it continues to grow. This deficit is amended with imports, which – in their own turn – are limited by the high level of global prices. The build-up issue of raw materials imports is going to solve by the measures of monetary policy (RMB’s revaluation against the USD. Analysis of China’s market of raw materials reveals that the largest increase in the physical volume of imports is concentrated in crude oil, LNG, iron ore and coal. As for Russia, its supplies and share in total Chinese imports of raw materials tend to increase. Author employs regression equations based on international statistics data to show that RMB’s revaluation, ceteris paribus, increases physical volumes of raw materials imports. However, the main factor of coal and LNG imports growth is energy consumption by Chinese heavy industry; imports of oil products – producers’ prices; meanwhile imports of steel products tend to decrease with the growth of steel exports. RMB’s revaluation increases physical volumes of imports of low value added raw materials from Russia (coal, crude oil, iron ore

Losses in the coal supply chain

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-12-15

This report examines the way coal can change as it passes along the coal chain. A great deal of the change is intended, through separation and sizing, to ensure the coal being mined matches the specification demanded by the customer. This report attempts to identify these changes and presents some of the issues faced by the coal supplier and user. Much of the change leads to a loss of mass in the coal. Some of the coal is left in the ground (intentionally and unintentionally), while elsewhere, full extraction might occur with the addition of non-coal materials from the surrounding rocks. In both cases, the mined coal often requires further processing. Coal processing by separation at preparation plants refines coal further and is where most of the mass loss occurs. Value is added by reducing ash content and improving heating value, thus providing a much more saleable product for the market. As soon as the coal leaves the mine, mass loss can occur either through natural deterioration of the fuel, through spillage or dust, or in extreme cases theft. In all cases measuring the amount of coal as it passes through the supply chain is required to verify that the coal reaching the consumer is of satisfactory quality and quantity. This can be done crudely by measuring stockpiles, to more sophisticated weighing systems at various points along the supply chain, and even measuring the volume held in a ship. Measurement is subject to error which must be minimised. Biomass needs to be processed in much the same way as coal, such as removing mineral matter and taking care in avoiding contamination.

Residual coal exploitation and its impact on sustainable development of the coal industry in China

International Nuclear Information System (INIS)

Zhang, Yujiang; Feng, Guorui; Zhang, Min; Ren, Hongrui; Bai, Jinwen; Guo, Yuxia; Jiang, Haina; Kang, Lixun

2016-01-01

Although China owns large coal reserves, it now faces the problem of depletion of its coal resources in advance. The coal-based energy mix in China will not change in the short term, and a means of delaying the coal resources depletion is therefore urgently required. The residual coal was exploited first with a lower recovery percentage and was evaluated as commercially valuable damaged coal. This approach is in comparison to past evaluations when the residual coal was allocated as exploitation losses. Coal recovery rates, the calculation method of residual coal reserves and statistics of its mines in China were given. On this basis, a discussion concerning the impacts on the delay of China's coal depletion, development of coal exploitation and sustainable developments, as well as technologies and relevant policies, were presented. It is considered that the exploitation of residual coal can effectively delay China's coal depletion, inhibit the construction of new mines, redress the imbalance between supply and demand of coal in eastern China, improve the mining area environment and guarantee social stability. The Chinese government supports the exploitation technologies of residual coal. Hence, exploiting residual coal is of considerable importance in sustainable development of the coal industry in China. - Highlights: •Pay attention to residual coal under changing energy-mix environment in China. •Estimate residual coal reserves and investigate its exploitation mines. •Discuss impacts of residual coal exploitation on delay of coal depletion in China. •Discuss impacts on coal mining industry and residual coal exploitation technology. •Give corresponding policy prescriptions.

Extreme coal handling

Energy Technology Data Exchange (ETDEWEB)

Bradbury, S; Homleid, D. [Air Control Science Inc. (United States)

2004-04-01

Within the journals 'Focus on O & M' is a short article describing modifications to coal handling systems at Eielson Air Force Base near Fairbanks, Alaska, which is supplied with power and heat from a subbituminous coal-fired central plant. Measures to reduce dust include addition of an enclosed recirculation chamber at each transfer point and new chute designs to reduce coal velocity, turbulence, and induced air. The modifications were developed by Air Control Science (ACS). 7 figs., 1 tab.

POTENTIAL OF LIVESTOCK MANURE FOR COAL ACTIVATION

Directory of Open Access Journals (Sweden)

EllIN HARlIA HARlIA

2017-06-01

Full Text Available The natural methane formed by bacteria in anaerobic conditions is known as biogenic gas. Gas trapped in coal, formed through thermogenesis as well as biogenesisis known as coal-bed methane (CBM. The availability of organic material as decomposition of this material into methane is continuously required for the production of methane in the coal aquifer. The aim of this research was to investigate whether or not cattle feces bacteria were able to grow and produce methane in coal. Parameters measured were Volatile Fatty Acids (VFA and the production of biogas, such as nitrogen, hydrogen, carbon dioxide, and methane. Explorative method was used and data obtained was analyzed by descriptive approach. The results showed that the bacteria found in the feces survived in the coal and produce biogas. On day 2 when the process was at the acidogenesis phase, it produced VFA with the largest component of acetic acid. Acetic acid would undergo decarboxylation and reduction of CO2 followed by reactions of H2and CO2 to produce methane (CH4 and carbon dioxide (CO2 as the final products. ,

Clean coal technologies: A business report

International Nuclear Information System (INIS)

Anon.

1993-01-01

The book contains four sections as follows: (1) Industry trends: US energy supply and demand; The clean coal industry; Opportunities in clean coal technologies; International market for clean coal technologies; and Clean Coal Technology Program, US Energy Department; (2) Environmental policy: Clean Air Act; Midwestern states' coal policy; European Community policy; and R ampersand D in the United Kingdom; (3) Clean coal technologies: Pre-combustion technologies; Combustion technologies; and Post-combustion technologies; (4) Clean coal companies. Separate abstracts have been prepared for several sections or subsections for inclusion on the data base

Radiant-and-plasma technology for coal processing

Directory of Open Access Journals (Sweden)

Vladimir Messerle

2012-12-01

Full Text Available Radiant-and-plasma technology for coal processing is presented in the article. Thermodynamic computation and experiments on plasma processing of bituminous coal preliminary electron-beam activated were fulfilled in comparison with plasma processing of the coal. Positive influence of the preliminary electron-beam activation of coal on synthesis gas yield was found. Experiments were carried out in the plasma gasifier of 100 kW power. As a result of the measurements of material and heat balance of the process gave the following integral indicators: weight-average temperature of 2200-2300 K, and carbon gasification degree of 82,4-83,2%. Synthesis gas yield at thermochemical preparation of raw coal dust for burning was 24,5% and in the case of electron-beam activation of coal synthesis gas yield reached 36,4%, which is 48% higher.

Intelligent control and maintenance of management integrated system based on multi-agents for coal preparation plant

Energy Technology Data Exchange (ETDEWEB)

Meng, F.; Wang, Y. [China University of Mining and technology, Xuzhou (China). School of Information and Electrical Engineering

2006-06-15

This paper discusses the progress of computer integrated processing (CIPS) of coal preparation and then presents an intelligence controlled production process, device-maintenance and production-management system of coal preparation based on multi-agents (IICMMS-CP). The construction of the IICMMS-CP, the distributed network control system based on live intelligence control stations and the strategy of implementing a distributed intelligence control system are studied in order to overcome the disadvantages brought about by the wide use of the PLC system by coal preparation plants. The software frame, based on a Multi-Agent Intelligence Control and Maintenance Management integrated system, is studied and the implementation methods of IICMMS-CP are discussed. The characteristics of distributed architecture, cooperation and parallel computing meet the needs of integrated control of coal preparation plants with large-scale spatial production distribution, densely-related processes and complex systems. Its application further improves the reliability and precision of process control, accuracy of fault identification and intelligence of production adjustment, establishes a technical basis for system integration and flexible production. The main function of the system has been tested in a coal preparation plant to good effect in stabilizing product quality, improving efficiency and reducing consumption. 17 refs., 4 figs.

Contents and occurrence of cadmium in the coals from Guizhou province, China.

Science.gov (United States)

Song, Dangyu; Wang, Mingshi; Zhang, Junying; Zheng, Chuguang

2008-10-01

Eleven raw coal samples were collected from Liuzhi, Suicheng, Zunyi, Xingren, Xingyi, and Anlong districts in Guizhou Province, Southwest China. The content of cadmium (Cd) in coal was determined using inductively coupled plasma mass-spectrometry (ICP-MS). Cd contents ranged from 0.146 to 2.74 ppm (whole coal basis), with an average of 1.09 ppm. In comparison with the arithmetic means of Cd in Chinese coal (0.25 ppm), this is much higher. In order to find its occurrence in coal, float-sink analysis and a coal flotation test by progressive release were conducted on two raw coal samples. The content of the Cd and ash yield of the flotation products were determined. The organic matter was removed by low-temperature ashing (LTA). X-ray diffraction (XRD) was used to differentiate the main, minor, and trace minerals in the LTA from different flotation subproducts. Quartz, kaolinite, pyrite, and calcite were found to dominate the mineral matters, with a proportion of anatase, muscovite, and illite. Then quantitative analysis of minerals in LTA was conducted using material analysis using diffraction (MAUD) based on the Rietveld refinement method. Results show that Cd has a strong association with kaolinite.

Contents and occurrence of cadmium in the coals from Guizhou Province, China

Energy Technology Data Exchange (ETDEWEB)

Dangyu Song; Mingshi Wang; Junying Zhang; Chuguang Zheng [Henan Polytechnic University, Jiaozuo (China). Institute of Resources and Environment

2008-10-15

Eleven raw coal samples were collected from Liuzhi, Suicheng, Zunyi, Xingren, Xingyi, and Anlong districts in Guizhou Province, Southwest China. The content of cadmium (Cd) in coal was determined using inductively coupled plasma mass-spectrometry (ICP-MS). Cd contents ranged from 0.146 to 2.74 ppm (whole coal basis), with an average of 1.09 ppm. In comparison with the arithmetic means of Cd in Chinese coal (0.25 ppm), this is much higher. In order to find its occurrence in coal, float-sink analysis and a coal flotation test by progressive release were conducted on two raw coal samples. The content of the Cd and ash yield of the flotation products were determined. The organic matter was removed by low-temperature ashing (LTA). X-ray diffraction (XRD) was used to differentiate the main, minor, and trace minerals in the LTA from different flotation subproducts. Quartz, kaolinite, pyrite, and calcite were found to dominate the mineral matters, with a proportion of anatase, muscovite, and illite. Then quantitative analysis of minerals in LTA was conducted using material analysis using diffraction (MAUD) based on the Rietveld refinement method. Results show that Cd has a strong association with kaolinite.

Use of new ceramic linings in coal preparation plants

Energy Technology Data Exchange (ETDEWEB)

Fedorchenko, V.E.; Rudenko, V.A.; Bondarev, A.Ya.

1984-01-01

This article evaluates several materials used as liners in coal preparation equipment. The evaluations concentrate on liners used under conditions of intensive temperature fluctuations, e.g. liners of coal chutes for coal transport from coal dryers. Two aspects of wear are analyzed: abrasion by friction and effects of temperature fluctuations. Abrasive wear is tested using magnetite suspension with a density of 400 g/l. Tests show that abrasive wear of liners on an alumina basis is 3 times lower than abrasive wear of high quality steel, from 13 to 24 times lower than that of iron and from 6 to 8 times lower than that of steels used in coal preparation plants. Effects of temperature fluctuations from 20 to 840 C on abrasive wear of liners of steels, iron, slag glass ceramics, mullite-corundum material and corundum is shown in a table. The test show that mullite-corundum material on the basis of alumina is characterized by a high resistance to abrasive wear after 30 cycles of temperature increase from 20 to 840 C and decrease to 20 C. Using mullite-corundum as liners of equipment and installations operating under conditions of temperature fluctuations is recommended.

ANN-GA based optimization of a high ash coal-fired supercritical power plant

International Nuclear Information System (INIS)

Suresh, M.V.J.J.; Reddy, K.S.; Kolar, Ajit Kumar

2011-01-01

Highlights: → Neuro-genetic power plant optimization is found to be an efficient methodology. → Advantage of neuro-genetic algorithm is the possibility of on-line optimization. → Exergy loss in combustor indicates the effect of coal composition on efficiency. -- Abstract: The efficiency of coal-fired power plant depends on various operating parameters such as main steam/reheat steam pressures and temperatures, turbine extraction pressures, and excess air ratio for a given fuel. However, simultaneous optimization of all these operating parameters to achieve the maximum plant efficiency is a challenging task. This study deals with the coupled ANN and GA based (neuro-genetic) optimization of a high ash coal-fired supercritical power plant in Indian climatic condition to determine the maximum possible plant efficiency. The power plant simulation data obtained from a flow-sheet program, 'Cycle-Tempo' is used to train the artificial neural network (ANN) to predict the energy input through fuel (coal). The optimum set of various operating parameters that result in the minimum energy input to the power plant is then determined by coupling the trained ANN model as a fitness function with the genetic algorithm (GA). A unit size of 800 MWe currently under development in India is considered to carry out the thermodynamic analysis based on energy and exergy. Apart from optimizing the design parameters, the developed model can also be used for on-line optimization when quick response is required. Furthermore, the effect of various coals on the thermodynamic performance of the optimized power plant is also determined.

Study on surface morphology and physicochemical properties of raw and activated South African coal and coal fly ash

Science.gov (United States)

Mishra, S. B.; Langwenya, S. P.; Mamba, B. B.; Balakrishnan, M.

South African coal and coal fly ash were selected as the raw materials to be used for study of their morphology and physicochemical properties and their respective activated carbons for adsorption applications. Coal and fly ash were individually steam activated at a temperature range of 550-1000 °C for 1 h in a muffle furnace using cylindrical stainless steel containers. Scanning electron micrographs revealed a change in surface morphology with more mineral matter available on the surface of the coal particles due to increased devolatilization. However, in the case of fly ash, the macerals coalesced to form agglomerates and the presence of unburnt carbon constituted pores of diameter between 50 and 100 nm. The BET surface area of coal improved significantly from 5.31 to 52.12 m 2/g whereas in case of fly ash the surface area of the raw sample which was originally 0.59 m 2/g and upon activation increased only up to 2.04 m 2/g. The chemical composition of the fly ash confirmed that silica was the major component which was approximately 60% by weight fraction. The impact of this study was to highlight the importance of using raw materials such as coal and a waste product, in the form of coal ash, in order to produce affordable activated carbon that can be used in drinking water treatment. This would therefore ensure that the quality of water supplied to communities for drinking is not contaminated especially by toxic organic compounds.

U.S. Coal Fields

Data.gov (United States)

Department of Homeland Security — This data set shows the coal fields of Alaska and the conterminous United States. Most of the material for the conterminous United States was collected from James...

Kyoto Protocol, constraint or opportunity for coal based electricity producers

International Nuclear Information System (INIS)

Balasoiu, Constantin; Alecu, Sorin

2006-01-01

Coming into force of Kyoto Protocol (KP) in February 2005, as a result of its signing by Russian Federation, created the lawfulness of its provisions and mechanisms in order to reduce the average emission of Greenhouse Gases (GHG) at a global level down to 5.2 %. Passing this environment problem from a constrained area (regulations, directives) to an opportunity area (business) created the possibility that the achievement of KP objectives to be not an exclusive financial task of 'polluting actors', but opened the opportunity of bringing on stage all the necessary elements of a modern business environment: banks, investments from founds companies, consultants, buyers, sellers, stocks exchange. Until now, the investments and emissions transactions based by KP mechanisms at the worldwide level was focused on renewable energy area. Because for the most of countries, including Romania, the production of electricity based on fossil fuels (special coal) is one of the main option, bringing the KP mechanisms in operation in this area is difficult for at least two reasons: - the investments are huge; - the emissions reduction is not spectacular. In these circumstances, this paper gives an overview of the present GHG emission market, transaction mechanisms on this market and of the ways through which coal based electricity producers from Romania can access this market. We consider that the filtration of the information in this area from electricity producer point of view makes the content of this paper a good start for a new approach of environment management and its conversion from constraint (financial resources consumer) to opportunity ( financial resources producer). The paper contains are as follows: 1. Kyoto Protocol at a glance; 2. Emission trading mechanisms; 2.1. Transaction mechanisms under KP; 2.1.1. Joint Implementation (JI); 2.1.2 Clean Development Mechanism (CDM); 2.1.3. Emissions Trading (ET); 2.2. Other transactions mechanisms; 2.2.1. European Union Emissions

Particular cases of materials balance equation generalized for gas deposits associated to the coal

International Nuclear Information System (INIS)

Penuela, G; Ordonez, A; Bejarano, A

1997-01-01

One of the fundamental principles used in the work, developed in engineering is the law of the matter conservation. The application of this principle to the hydrocarbons fields, with the purpose of to quantify and to be predicted expresses by means of materials balance method. While the equation construction of conventional materials balance and the calculations that come with their application are not a difficult task, the approach of selection of the solution that better it represents the deposit it is one of the problems that the petroleum engineer should face. The materials balance is a useful analysis method of the deposit operation, reserves estimate of raw and gas, and prediction of the future behavior of the deposit. The coal, beds, devonian shales and geo pressurized-aquifer are some examples of natural gas sources and to possess production mechanisms and behaviors significantly different to the traditional than have been considered as non conventional deposits

PRODUCTION OF FOAMS, FIBERS AND PITCHES USING A COAL EXTRACTION PROCESS

Energy Technology Data Exchange (ETDEWEB)

Chong Chen; Elliot B. Kennel; Liviu Magean; Pete G. Stansberry; Alfred H. Stiller; John W. Zondlo

2004-06-20

This Department of Energy National Energy Technology Laboratory sponsored project developed processes for converting coal feedstocks to carbon products, including coal-derived pitch, coke foams and fibers based on solvent extraction processes. A key technology is the use of hydrogenation accomplished at elevated temperatures and pressures to obtain a synthetic coal pitch. Hydrogenation, or partial direct liquefaction of coal, is used to modify the properties of raw coal such that a molten synthetic pitch can be obtained. The amount of hydrogen required to produce a synthetic pitch is about an order of magnitude less than the amount required to produce synthetic crude oil. Hence the conditions for synthetic pitch production consume very little hydrogen and can be accomplished at substantially lower pressure. In the molten state, hot filtration or centrifugation can be used to separate dissolved coal chemicals from mineral matter and insolubles (inertinite), resulting in the production of a purified hydrocarbon pitch. Alternatively, if hydrogenation is not used, aromatic hydrocarbon liquids appropriate for use as precursors to carbon products can obtained by dissolving coal in a solvent. As in the case for partial direct liquefaction pitches, undissolved coal is removed via hot filtration or centrifugation. Excess solvent is boiled off and recovered. The resultant solid material, referred to as Solvent Extracted Carbon Ore or SECO, has been used successfully to produce artificial graphite and carbon foam.

Coal and recycling mark the way forward

Energy Technology Data Exchange (ETDEWEB)

Bignell, E.

2000-11-01

A report is given of this year's Mineral Engineering Society's annual conference held in Scarborough, UK. The themes of recycling and coal were chosen for the two days of technical presentations. Topics included the cleaning up of brown field sites; the use of recycled waste oxide to replace iron ore pellets for cooling furnaces in steel making; high pressure filtration of industrial mineral effluent; iron ore mining in Australia; screen development; the status of coal preparation technology, by RJB Mining; study of movement of material (to simulate coal) in a hopper; and a UK-Chinese project on reduction of sulphur in coal.

On changes in bed-material particles from a 550 MWth CFB boiler burning coal, bark and peat

Energy Technology Data Exchange (ETDEWEB)

Vesna Barisic; Mikko Hupa [Aabo Akademi Process Chemistry Centre, Turku (Finland). Combustion and Materials Chemistry

2007-02-15

This paper presents our observations on coating build up, morphology and the elemental composition of bed-material particles collected from a 550 MWth CFB boiler burning coal, bark and peat fuel/fuel mixture. The special focus was on the changes of the elemental composition of coating layer on bed-material particles when different fuels were burned. The results were obtained using a scanning electron microscope coupled with an energy depressive X-ray analyser (SEM/EDX). The results clearly show that properties of bed-material particles are a result of complex interaction between the fuels burned previously, and the fuels used at the time of sampling. Short communication. 8 refs., 1 fig., 2 tabs.

Gas Concentration Prediction Based on the Measured Data of a Coal Mine Rescue Robot

Directory of Open Access Journals (Sweden)

Xiliang Ma

2016-01-01

Full Text Available The coal mine environment is complex and dangerous after gas accident; then a timely and effective rescue and relief work is necessary. Hence prediction of gas concentration in front of coal mine rescue robot is an important significance to ensure that the coal mine rescue robot carries out the exploration and search and rescue mission. In this paper, a gray neural network is proposed to predict the gas concentration 10 meters in front of the coal mine rescue robot based on the gas concentration, temperature, and wind speed of the current position and 1 meter in front. Subsequently the quantum genetic algorithm optimization gray neural network parameters of the gas concentration prediction method are proposed to get more accurate prediction of the gas concentration in the roadway. Experimental results show that a gray neural network optimized by the quantum genetic algorithm is more accurate for predicting the gas concentration. The overall prediction error is 9.12%, and the largest forecasting error is 11.36%; compared with gray neural network, the gas concentration prediction error increases by 55.23%. This means that the proposed method can better allow the coal mine rescue robot to accurately predict the gas concentration in the coal mine roadway.

Report on the FY 1998 results of the New Sunshine Project (B version). Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In 1994, a memorandum on the research cooperation was agreed between NEDO and BPPT (The Agency for the Assessment and Application Technology) in Indonesia, based on the request for the coal liquefaction technology cooperation from BPPT. It includes the following items: conference for professionals to be held, invitation and training of Indonesian engineers, activity for joint field survey and potential survey of location of coal liquefaction commercial plant. Further in 1997, the secondary memorandum was concluded for the potential survey for securing the hydrogen required for coal liquefaction by coal gasification. The survey was summarized as the potential survey for location of coal liquefaction. In the testing study for improving economical efficiency of liquefaction process, it was made clear that the higher the Fe content of Banko coal is, the higher the reaction of liquefaction is, and that Fe compounds in coal show catalysis. In the Soroako area in Sulawesi island, there are the nickel mine run by PT. Inco. Soroako limonite is promising as catalyst material for commercial-scale coal liquefaction. In the gasification method, the plant construction cost increases, but the production amount of coal-derived liquid can be increased. That is more profitable than the production of hydrogen from natural gas. (NEDO)

Size Effect on Acoustic Emission Characteristics of Coal-Rock Damage Evolution

OpenAIRE

Wen, Zhijie; Wang, Xiao; Chen, Lianjun; Lin, Guan; Zhang, Hualei

2017-01-01

Coal-gas outburst, rock burst, and other mine dynamic disasters are closely related to the instability and failure of coal-rock. Coal-rock is the assemblies of mineral particles of varying sizes and shapes bonded together by cementing materials. The damage and rupture process of coal-rock is accompanied by acoustic emission (AE), which can be used as an effective means to monitor and predict the instability of coal-rock body. In this manuscript, considering the size effect of coal-rock, the i...

Strength and corrosion behavior of SiC - based ceramics in hot coal combustion environments

Energy Technology Data Exchange (ETDEWEB)

Breder, K.; Parten, R.J. [Oak Ridge National Lab., TN (United States)

1996-08-01

As part of an effort to evaluate the use of advanced ceramics in a new generation of coal-fired power plants, four SiC-based ceramics have been exposed to corrosive coal slag in a laboratory furnace and two pilot scale combustors. Initial results indicate that the laboratory experiments are valuable additions to more expensive pilot plant experiments. The results show increased corrosive attack with increased temperature, and that only slight changes in temperature may significantly alter the degree of strength degradation due to corrosive attack. The present results are part of a larger experimental matrix evaluating the behavior of ceramics in the coal combustion environment.

Adsorption of iodine from COIL waste gas on soaked coal-based activated carbon

Science.gov (United States)

Zhou, Junbo; Hao, Shan; Gao, Liping

2014-04-01

The chemical oxygen-iodine laser (COIL) has wide application prospects in military, industrial and medical treatment fields as a second generation gas chemical laser to follow the first HF/DF chemical laser. However, a COIL releases large amounts of gas, such as helium, oxygen, chlorine and iodine. Chlorides have a serious corrosive effect on the system, especially iodine vapor crystallization, which seriously endangers the normal use of vacuum systems, and radioactive methyl iodide, which is hazardous to operators and pollutes the environment. The use of soaked coal-based activated carbon as an adsorbent for removing methyl iodine is proposed, while it is proposed that coal-based activated carbon is an effective adsorbent for removing stable iodine. The research conducted in this work shows that iodine residues are less than 0.5 μg ml-1 after the adsorption treatment and the decontamination factor of the coal-based activated carbon for removing stable iodine is more than 1000. Using this method can achieve the purpose of removing harmful iodine, satisfy the requirements for engineering applications, and also be applied to other nuclear power plant flue gas treatments.

A brief petrographic review on Nigerian coal resources

International Nuclear Information System (INIS)

Obaje, N. G.; Abaa, S. I.; Najime, T.; Suh, C. E.

2000-01-01

The coal resources of Nigeria are located mainly within the Benue Trough. In the lower Benue, subbituminous coals occur within the Maastrichtian Mamu Formation. High - volatile bituminous coals are found within the Turonian - Santonian Awgu Formation in the middle Benue while the upper Benue contains lignites and sub-bituminous coals in the Maastrichtian Gombe Sandstone Formation. Maceral analyses show that himinite dominates in the petrographic composition of the lower and upper Benue Trough coals with vitrinite reflectance values ranging from 0.30 to 0.63% Rm. In coals from the middle Benue, vitrinite macerals predominate and Rm values range from 0.74 to 1.25%. The present review suggests that the sub-bituminous coals in the lower and upper Benue are optimum for combustion and sub-optimum for liquefaction; while the high-volatile bituminous coals in the middle Benue, apart form being optimum for liquefaction, are the most suitable as raw material for coke making (carbonization) in steel manufacture

Study of the raw material base for a by-product coke plant by the method of thermal degradation of coal in a centrifugal field

Energy Technology Data Exchange (ETDEWEB)

Epimakhov, N.M.; Kardashova, V.F.; Sulimova, E.I.

1982-01-01

Coals from the Donbass and Karaganda basins, being supplied to a Bagley by-product coke plant were studied. A sharp distinction between coals of different degrees of metamorphism in respect to the yield of liquid nonvolatile products was demonstrated. A difference in respect to this index was recognized for individual coals from one and the same technological group from a single basin.

Analysis of coal by neutron activation

International Nuclear Information System (INIS)

Burtner, D.R.

1983-01-01

The development of a thermal-neutron activation analysis procedure for determining elemental concentrations in whole coal samples, and the goal of combining this technique with other nuclear methods for determining a total mass balance in these and similar complex materials, is described. Problems of applying a fast-neutron activation analysis method for nitrogen are discussed, as well as an efficient procedure for drying and packaging coal samples. A thermal-neutron activation analysis (TNAA) procedure was developed for determining up to 27 elements in coal samples from the US, China, Nigeria, and Brazil. The comparator form of TNAA was applied, using a unique multielement standard, which contained 48 elements. The difference in net photopeak counts between sample and standard, due to γ-ray attenuation, was reduced by preparing this standard in an organic matrix, which simulates the composition and physical structure of the coal material. The simultaneous irradiation of several aliquots of this standard enabled high precision and accuracy to be attained. An accurate value for oxygen, determined by fast-neutron activation analysis, is used to correct for this effect in the nitrogen determination method

Prediction of China's coal production-environmental pollution based on a hybrid genetic algorithm-system dynamics model

International Nuclear Information System (INIS)

Yu Shiwei; Wei Yiming

2012-01-01

This paper proposes a hybrid model based on genetic algorithm (GA) and system dynamics (SD) for coal production–environmental pollution load in China. GA has been utilized in the optimization of the parameters of the SD model to reduce implementation subjectivity. The chain of “Economic development–coal demand–coal production–environmental pollution load” of China in 2030 was predicted, and scenarios were analyzed. Results show that: (1) GA performs well in optimizing the parameters of the SD model objectively and in simulating the historical data; (2) The demand for coal energy continuously increases, although the coal intensity has actually decreased because of China's persistent economic development. Furthermore, instead of reaching a turning point by 2030, the environmental pollution load continuously increases each year even under the scenario where coal intensity decreased by 20% and investment in pollution abatement increased by 20%; (3) For abating the amount of “three types of wastes”, reducing the coal intensity is more effective than reducing the polluted production per tonne of coal and increasing investment in pollution control. - Highlights: ► We propos a GA-SD model for China's coal production-pollution prediction. ► Genetic algorithm (GA) can objectively and accurately optimize parameters of system dynamics (SD) model. ► Environmental pollution in China is projected to grow in our scenarios by 2030. ► The mechanism of reducing waste production per tonne of coal mining is more effective than others.

Low severity conversion of activated coal. Final report

Energy Technology Data Exchange (ETDEWEB)

Hirschon, A.S.; Ross, D.S.

1990-01-01

The results suggest that coal contains regions with structural components significantly reactive under the hydrothermal environment. Although the specific mechanism for this process remains to be developed, this activity is reminiscent of findings in studies of accelerated maturation of oil shale, where hydrothermal treatment (hydrous pyrolysis) leads to the production of petroleum hydrocarbons. In line with what has been seen in the oil shale work, the pretreatment-generated hydrocarbons and phenols appear to represent a further or more complete maturation of some fraction of the organic material within the coal. These observations could have an impact in two areas. The first is in the area of coal structure, where immature, reactive regions have not been included in the structures considered at present. The second area of interest is the more practical one of conversions to coal liquids and pyrolytic tars. It seems clear that the hydrothermal pretreatment changes the coal in some manner that favorably affects the product quality substantially and, as in the CO/water liquefaction case, favorably affects the yields. The conversions of coals of lower rank, i.e., less mature coals, could particularly benefit in terms of both product quality and product quantity. The second portion of this project also shows important benefits to coal conversion technology. It deals with synthesizing catalysts designed to cleave the weak links in the coal structure and then linking these catalysts with the pretreatment methods in Task 2. The results show that highly dispersed catalysts can effectively be used to increase the yields of soluble material. An important aspect of highly dispersed catalysts are that they can effectively catalyze coal conversion even in poor liquefaction solvents, thus making them very attractive in processes such as coprocessing where inexpensive liquefaction media such as resids are used.

Experimental Investigation of Coal Dust Wettability Based on Surface Contact Angle

Directory of Open Access Journals (Sweden)

Gang Zhou

2016-01-01

Full Text Available Wettability is one of the key chemical properties of coal dust, which is very important to dedusting. In this paper, the theory of liquid wetting solid was presented firstly; then, taking the gas coal of Xinglongzhuang coal mine in China as an example, by determination of critical surface tension of coal piece, it can be concluded that only when the surface tension of surfactant solution is less than 45 mN/m can the coal sample be fully wetted. Due to the effect of particle dispersity, compared with the contact angle of milled coal particle, not all the contact angles of screened coal powder with different sizes have a tendency to increase. Furthermore, by the experiments of coal samples’ specific surface areas and porosities, it can be achieved that the volume of single-point total pore decreases with the gradual decreasing of coal’s porosity, while the ultramicropores’ dispersities and multipoint BET specific surface areas increase. Besides, by a series of contact angle experiments with different surfactants, it can be found that with the increasing of porosity and the decreasing of volume percentage of ultramicropore, the contact angle tends to reduce gradually and the coal dust is much easier to get wetted.

Zinc isotopic composition of particulate matter generated during the combustion of coal and coal + tire-derived fuels

Science.gov (United States)

Borrok, D.M.; Gieré, R.; Ren, M.; Landa, E.R.

2010-01-01

Atmospheric Zn emissions from the burning of coal and tire-derived fuel (TDF) for power generation can be considerable. In an effort to lay the foundation for tracking these contributions, we evaluated the Zn isotopes of coal, a mixture of 95 wt % coal + 5 wt % TDF, and the particulate matter (PM) derived from their combustion in a power-generating plant. The average Zn concentrations and δ(66)Zn were 36 mg/kg and 183 mg/kg and +0.24‰ and +0.13‰ for the coal and coal + TDF, respectively. The δ(66)Zn of the PM sequestered in the cyclone-type mechanical separator was the lightest measured, -0.48‰ for coal and -0.81‰ for coal+TDF. The δ(66)Zn of the PM from the electrostatic precipitator showed a slight enrichment in the heavier Zn isotopes relative to the starting material. PM collected from the stack had the heaviest δ(66)Zn in the system, +0.63‰ and +0.50‰ for the coal and coal + TDF, respectively. Initial fractionation during the generation of a Zn-rich vapor is followed by temperature-dependent fractionation as Zn condenses onto the PM. The isotopic changes of the two fuel types are similar, suggesting that their inherent chemical differences have only a secondary impact on the isotopic fractionation process.

PNNL Coal Gasification Research

Energy Technology Data Exchange (ETDEWEB)

Reid, Douglas J.; Cabe, James E.; Bearden, Mark D.

2010-07-28

This report explains the goals of PNNL in relation to coal gasification research. The long-term intent of this effort is to produce a syngas product for use by internal Pacific Northwest National Laboratory (PNNL) researchers in materials, catalysts, and instrumentation development. Future work on the project will focus on improving the reliability and performance of the gasifier, with a goal of continuous operation for 4 hours using coal feedstock. In addition, system modifications to increase operational flexibility and reliability or accommodate other fuel sources that can be used for syngas production could be useful.

Coal-peat compositions for co-combustion in local boilers

Directory of Open Access Journals (Sweden)

А. В. Михайлов

2016-08-01

Full Text Available In article results of experiments on creation of coal and peat fuel compositions for burning in solid-fuel boilers are described. The main objective of research consisted in development of combination of coal dust and natural peat without binding additives. The role of peat consists that it increases efficiency of process of granulation, being natural binding. The method of granulation allows to utilize waste of the coal industry. Joint burning of two types of fuel – coal dust and peat reduces emission of sulfur dioxides. The cost of peat raw materials is lower, than artificial binding, applied to briquetting of coal dust. The composition of mix of coal dust and peat varied in the ratio 2:1, 1:1 and 1:2 in volume ratio at humidity of mix before extrusion of 65 %. In the course of preparatory operations of coal raw materials its crushing and sifting through sieve of 24 mesh (0,707 mm was carried out. Procedure of hashing of samples of coal and peat was carried out before receiving homogeneous mixture. After hashing mix was located in piston press for receiving granules. Coal dust and wet peat pass semifixed extrusion on piston press with formation of cylindrical granules with a diameter of 16 mm. After extrusion of granule are dried to operational humidity of 25 %. Coal and peat fuel granules showed sufficient mechanical strength for transportation and power feed in solid-fuel boilers. Burning of coal and peat fuel granules in vitro at temperature of 800 °C does not lead to ashes agglomeration. The conducted preliminary researches showed prospects of utilization of coal waste by granulation method in mix with natural peat.

DEVELOPMENT OF CONTINUOUS SOLVENT EXTRACTION PROCESSES FOR COAL DERIVED CARBON PRODUCTS

Energy Technology Data Exchange (ETDEWEB)

Elliot B. Kennel; Philip L. Biedler; Chong Chen; Dady Dadyburjor; Liviu Magean; Peter G. Stansberry; Alfred H. Stiller; John W. Zondlo

2005-04-13

The purpose of this DOE-funded effort is to develop continuous processes for solvent extraction of coal for the production of carbon products. These carbon products include materials used in metals smelting, especially in the aluminum and steel industries, as well as porous carbon structural material referred to as ''carbon foam'' and carbon fibers. A process has been developed which results in high quality binder pitch suitable for use in graphite electrodes or carbon anodes. A detailed description of the protocol is given by Clendenin. Briefly, aromatic heavy oils are hydro-treated under mild conditions in order to increase their ability to dissolve coal. An example of an aromatic heavy oil is Koppers Carbon Black Base (CBB) oil. CBB oil has been found to be an effective solvent and acceptably low cost (i.e., significantly below the market price for binder pitch, or about $280 per ton at the time of this writing). It is also possible to use solvents derived from hydrotreated coal and avoid reliance on coke oven recovery products completely if so desired.

Clean coal technology challenges for China

Energy Technology Data Exchange (ETDEWEB)

Mao, J. [Tsinghua University, Beijing (China). Dept. of Thermal Engineering

2001-01-01

China is rich in coal reserves and also the largest coal producer and consumer in the world. Coal constitutes over 70% of the total energy consumption, some 86% of coal production is burned directly, which causes serious air pollution problems. However, based on China's specific energy structure, coal utilisation will remain the dominant means of energy usage and clean coal technology must be the way forward if the environmental problems are to be resolved. This article discusses China's Clean Coal Technology Program, its implementation, including the clean coal technologies being developed and introduced, with reference to the key R & D institutes for each of the coal-using sectors. The article is an edited version of the 2000 Robens Coal Science Lecture, delivered in London in October 2000. The China Coal Technology Program for the 9th Five-Year Plan (1996-2000) was approved in 1997. The technologies included in the Program considered in this article are in: coal washing and grading, coal briquette, coal water slurry; circulating fluidised bed technology; pressurised fluidised bed combined cycle; integrated gasification combined cycle; coal gasification, coal liquefaction and flue gas desulfurisation. 4 tabs.

Initiative hard coal; Initiative Steinkohle

Energy Technology Data Exchange (ETDEWEB)

Leonhardt, J.

2007-08-02

In order to decrease the import dependence of hard coal in the European Union, the author has submitted suggestions to the director of conventional sources of energy (directorate general for energy and transport) of the European community, which found a positive resonance. These suggestions are summarized in an elaboration 'Initiative Hard Coal'. After clarifying the starting situation and defining the target the presupposition for a better use of hard coal deposits as raw material in the European Union are pointed out. On that basis concrete suggestions for measures are made. Apart from the conditions of the deposits it concerns thereby also new mining techniques and mining-economical developments, connected with tasks for the mining-machine industry. (orig.)

Coal preparation

International Nuclear Information System (INIS)

Anon.

1991-01-01

The acid rain control legislation has prompted the Department of Energy (DOE) to seek new technology using the Clean Coal Technology program solicitation. The main goal of the program is to reduce SO 2 emissions below 9 Mt/a (10 million stpy) and NO x emission below 5.4 Mt/a (6 million stpy) by the year 2000. This would be accomplished by using precombustion, combustion, post combustion and conversion technology. Utilities are considering installing new scrubbers, switching fuel or possibly deep clean. However, the time required to implement the control technology is short. Due to the legislation, about 110 plants will have to adopt one of the approaches. This paper reports that in characterization of coal, Ames Laboratory used a scanning electron microscope- based, automated image analysis (SEM-AIA) technique to identify coal and mineral matter association. Various forms of organic sulfur were identified using peroxyacetic acid oxidation of coal. This was followed by subsequent microscopic, GC-MS, and HRMS analysis by Southern Illinois University. In ultrafine grinding of coal, it was reported by the Mining and Mineral Institute of Alabama that silica sand or flint shot used less energy compared to steel ball mills

Study on HOPE Management Mode of Coal Enterprises Based on Systematic Thinking

Science.gov (United States)

Zhaoran, Zhang; Tianzhu, Zhang; Wenjing, Tong

2018-02-01

The extensive management mode of coal enterprises is no longer applicable to the demand of enterprise development under the new economic situation. Combined with the characteristics of coal mine production, based on the system of thinking, integration of lean, people, comprehensive, job management theory, formed HOPE management model, including a core system and three support systems and 18 elements. There are three stages in the development and implementation of this model. To 6S site management for the initial stage to job process reengineering for the intermediate stage to post value process control for the advanced stage. The successful implementation of HOPE model in coal enterprises needs comprehensive control from five aspects: lean culture construction, flattening organizational structure, cost control system, performance appraisal system and lean information management platform. HOPE model can be implemented smoothly and make “win-win” between enterprises and employees.

Material and Energy Flow Analysis (Mefa of the Unconventional Method of Electricity Production Based on Underground Coal Gasification

Directory of Open Access Journals (Sweden)

Krystyna Czaplicka-Kolarz

2014-01-01

Originality/value: This is the first approach which contains a whole chain of electricity production from Underground Coal Gasification, including stages of gas cleaning, electricity production and the additional capture of carbon dioxide.

Observer-Based Fuel Control Using Oxygen Measurement. A study based on a first-principles model of a pulverized coal fired Benson Boiler

Energy Technology Data Exchange (ETDEWEB)

Andersen, Palle; Bendtsen, Jan Dimon; Mortensen, Jan Henrik; Just Nielsen, Rene; Soendergaard Pedersen, Tom [Aalborg Univ. (Denmark). Dept. of Control Engineering

2005-01-01

This report describes an attempt to improve the existing control of coal mills used at the Danish power plant Nordjyllandsvaerket Unit 3. The coal mills pulverize raw coal to a fine-grained powder, which is injected into the furnace of the power plant. In the furnace the coal is combusted, producing heat, which is used for steam production. With better control of the coal mills, the power plant can be controlled more efficiently during load changes, thus improving the overall availability and efficiency of the plant. One of the main difficulties from a control point of view is that the coal mills are not equipped with sensors that detect how much coal is injected into the furnace. During the project, a fairly detailed, non-linear differential equation model of the furnace and the steam circuit was constructed and validated against data obtained at the plant. It was observed that this model was able to capture most of the important dynamics found in the data. Based on this model, it is possible to extract linearized models in various operating points. The report discusses this approach and illustrates how the model can be linearized and reduced to a lower-order linear model that is valid in the vicinity of an operating point by removing states that have little influence on the overall response. A viable adaptive control strategy would then be to design controllers for each of these simplified linear models, i.e., the control loop that sets references to the coal mills and feedwater, and use the load as a separate input to the control. The control gains should then be scheduled according to the load. However, the variations and uncertainties in the coal mill are not addressed directly in this approach. Another control approach was taken in this project, where a Kalman filter based on measurements of air flow blown into the furnace and the oxygen concentration in the flue gas is designed to estimate the actual coal flow injected into the furnace. With this estimate

Coal: an economic source of energy

International Nuclear Information System (INIS)

Ali, I.; Ali, M.M.

2001-01-01

Coal, in spite its abundance availability in Pakistan, is a neglected source of energy. Its role as fuel is not more than five percent for the last four decades. Some of the coal, mined, in used as space heating in cold areas of Pakistan but more than 90% is being used in brick kilns. There are 185 billion tonnes of coal reserves in the country and hardly 3 million tonnes of coal is, annually, mined. Lakhra coal field is, presently, major source of coal and is considered the largest productive/operative coal field of Pakistan. It is cheaper coal compared to other coals available in Pakistan. As an average analysis of colas of the country, it shows that most of the coals are lignitic in nature with high ash and sulfur content. The energy potential is roughly the same but the cost/ton of coal is quite different. It may be due to methods of mining. There should be some criteria for fixing the cost of the coal. It should be based on energy potential of unit mass of coal. (author)

Gastric cancer in coal miners: an hypothesis of coal mine dust causation

Energy Technology Data Exchange (ETDEWEB)

Ong, T M; Whong, W Z; Ames, R G

1983-10-01

An hypothesis is proposed to explain the elevated incidence of gastric cancer among coal miners. Inhaled coal mine dust, especially the larger particles, is cleared from the lung and tracheobronchial tree by mucociliary function, swallowed, and introduced into the stomach. Organic and/or inorganic materials in the dust can undergo intra-gastric nitrosation and/or interaction with exogenous chemicals to form carcinogenic compounds which in turn may lead to precancerous lesions, which may subsequently develop into gastric cancer. This sequence of events, however, depends upon occupational exposures as well as life-style features and individual genetic predisposition.

Switching and optimizing control for coal flotation process based on a hybrid model

Science.gov (United States)

Dong, Zhiyong; Wang, Ranfeng; Fan, Minqiang; Fu, Xiang

2017-01-01

Flotation is an important part of coal preparation, and the flotation column is widely applied as efficient flotation equipment. This process is complex and affected by many factors, with the froth depth and reagent dosage being two of the most important and frequently manipulated variables. This paper proposes a new method of switching and optimizing control for the coal flotation process. A hybrid model is built and evaluated using industrial data. First, wavelet analysis and principal component analysis (PCA) are applied for signal pre-processing. Second, a control model for optimizing the set point of the froth depth is constructed based on fuzzy control, and a control model is designed to optimize the reagent dosages based on expert system. Finally, the least squares-support vector machine (LS-SVM) is used to identify the operating conditions of the flotation process and to select one of the two models (froth depth or reagent dosage) for subsequent operation according to the condition parameters. The hybrid model is developed and evaluated on an industrial coal flotation column and exhibits satisfactory performance. PMID:29040305

Coal geopolitics

International Nuclear Information System (INIS)

Giraud, P.N.; Suissa, A.; Coiffard, J.; Cretin, D.

1991-01-01

This book divided into seven chapters, describes coal economic cycle. Chapter one: coals definition; the principle characteristics and properties (origin, calorific power, international classification...) Chapter two: the international coal cycle: coal mining, exploration, coal reserves estimation, coal handling coal industry and environmental impacts. Chapter three: the world coal reserves. Chapter four: the consumptions, productions and trade. Chapter five: the international coal market (exporting mining companies; importing companies; distributors and spot market operators) chapter six: the international coal trade chapter seven: the coal price formation. 234 refs.; 94 figs. and tabs [fr

Disposal and reclamation of southwestern coal and uranium wastes

International Nuclear Information System (INIS)

Wewerka, E.M.

1979-01-01

The types of solid wastes and effluents produced by the southwestern coal and uranium mining and milling industries are considered, and the current methods for the disposal and reclamation of these materials discussed. The major means of disposing of the solid wastes from both industries is by land fill or in some instances ponding. Sludges or aqueous wastes are normally discharged into settling and evaporative ponds. Basic reclamation measures for nearly all coal and uranium waste disposal sites include solids stabilization, compacting, grading, soil preparation, and revegetation. Impermeable liners and caps are beginning to be applied to disposal sites for some of the more harmful coal and uranium waste materials

Carbon formation and metal dusting in hot-gas cleanup systems of coal gasifiers

Energy Technology Data Exchange (ETDEWEB)

Judkins, R.R.; Tortorelli, P.F.; Judkins, R.R.; DeVan, J.H.; Wright, I.G. [Oak Ridge National Lab., TN (United States). Metals and Ceramics Div.

1995-11-01

The product gas resulting from the partial oxidation of Carboniferous materials in a gasifier is typically characterized by high carbon and sulfur, but low oxygen, activities and, consequently, severe degradation of the structural and functional materials can occur. The objective of this task was to establish the potential risks of carbon deposition and metal dusting in advanced coal gasification processes by examining the current state of knowledge regarding these phenomena, making appropriate thermochemical calculations for representative coal gasifiers, and addressing possible mitigation methods. The paper discusses carbon activities, iron-based phase stabilities, steam injection, conditions that influence kinetics of carbon deposition, and influence of system operating parameters on carbon deposition and metal dusting.

Lawrence Livermore National Laboratory underground coal gasification data base. [US DOE-supported field tests; data

Energy Technology Data Exchange (ETDEWEB)

Cena, R. J.; Thorsness, C. B.

1981-08-21

The Department of Energy has sponsored a number of field projects to determine the feasibility of converting the nation's vast coal reserves into a clean efficient energy source via underground coal gasification (UCG). Due to these tests, a significant data base of process information has developed covering a range of coal seams (flat subbituminous, deep flat bituminous and steeply dipping subbituminous) and processing techniques. A summary of all DOE-sponsored tests to data is shown. The development of UCG on a commercial scale requires involvement from both the public and private sectors. However, without detailed process information, accurate assessments of the commercial viability of UCG cannot be determined. To help overcome this problem the DOE has directed the Lawrence Livermore National Laboratory (LLNL) to develop a UCG data base containing raw and reduced process data from all DOE-sponsored field tests. It is our intent to make the data base available upon request to interested parties, to help them assess the true potential of UCG.

Abstracts and research accomplishments of university coal research projects

Energy Technology Data Exchange (ETDEWEB)

1991-06-01

The Principal Investigators of the grants supported by the University Coal Research Program were requested to submit abstracts and highlight accomplishments of their projects in time for distribution at a grantees conference. This book is a compilation of the material received in response to the request. Abstracts discuss the following area: coal science, coal surface science, reaction chemistry, advanced process concepts, engineering fundamentals and thermodynamics, environmental science.