Alcohol biodiesel from frying oil residues; Biodiesel etilico a partir de oleo de fritura residual

Energy Technology Data Exchange (ETDEWEB)

Festa, Brunna Simoes; Marques, Luiz Guilherme da Costa [Universidade Federal do Rio de Janeiro (IVIG/COPPE/UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia. Inst. Virtual Internacional de Mudancas Globais], E-mail: lguilherme@ivig.coppe.ufrj.br

2010-07-01

This paper describes the reaction optimization and production of biodiesel through the use of frying residual oil made available by the restaurant placed at the PETROBRAS Research Center (CENPES-RJ), using ethanol, so that to permit the production of sustainable bio diesel. The environmental gains obtained by the utilization of residual oil, avoiding that this oil be released in the nature, and the economic gains coming from the generation and utilization of ethanol allowing the production of biodiesel be an viable alternative. The obtained results during laboratory tests shown that biodiesel produced from the transesterification in alkaline medium, of the frying residual oil collected presented a reaction yield of approximately 80% considering in mass.

Flow condensation pressure drop characteristics of R410A-oil mixture inside small diameter horizontal microfin tubes

Energy Technology Data Exchange (ETDEWEB)

Huang, Xiangchao; Ding, Guoliang; Hu, Haitao; Zhu, Yu [Institute of Refrigeration and Cryogenics, Shanghai Jiaotong University, Shanghai 200240 (China); Gao, Yifeng [International Copper Association Shanghai Office, Shanghai 200020 (China); Deng, Bin [Institute of Heat Transfer Technology, Golden Dragon Precise Copper Tube Group Inc., Shanghai 200135 (China)

2010-11-15

Flow condensation pressure drop characteristics of R410A-oil mixture inside small diameter (5.0 mm and 4.0 mm O.D.) horizontal microfin tubes were investigated experimentally covering nominal oil concentrations from 0% to 5%. The research results indicate that, comparing with the frictional pressure drop of pure R410A, the frictional pressure drop of R410A-oil mixture may decrease by maximum of 18% when the vapor quality is lower than 0.6, and increase by maximum of 13% when the vapor quality is higher than 0.6. A new frictional pressure drop correlation for R410A-oil mixture flow condensation inside microfin tubes is developed based on the refrigerant-oil mixture properties, and can agree with 94% of the experimental data within a deviation of -30% to +30%. (author)

Characteristic of oil palm residue for energy conversion system

International Nuclear Information System (INIS)

Muharnif; Zainal, Z.A.

2006-01-01

Malaysia is the major producer of palm oil in the world. It produces 8.5 tones per year (8.5 x 10 6 ty -1 ) of palm oil from 38.6 x 10 6 ty - 1 of fresh fruit bunches. Palm oil production generates large amounts of process residue such as fiber (5.4 x 10 6 ty - 1 ), shell (2.3 x 10 6 ty - 1 ), and empty fruit bunches (8.8 x 10 6 ty - 1 ). A large fraction of the fiber and much of the shell are used as fuel to generate process steam and electricity. The appropriate energy conversion system depends on the characteristic of the oil palm residue. In this paper, a description of characteristic of the oil palm residue is presented. The types of the energy conversion system presented are stoker type combustor and gasified. The paper focuses on the pulverized biomass material and the use of fluidized bed gasified. In the fluidized bed gasified, the palm shell and fiber has to be pulverized before feeding into gasified. For downdraft gasified and furnace, the palm shell and fiber can be used directly into the reactor for energy conversion. The heating value, burning characteristic, ash and moisture content of the oil palm residue are other parameters of the study

CO2 Enhanced Oil Recovery from the Residual Zone - A Sustainable Vision for North Sea Oil Production

Science.gov (United States)

Stewart, Jamie; Haszeldine, Stuart; Wilkinson, Mark; Johnson, Gareth

2014-05-01

This paper presents a 'new vision for North Sea oil production' where previously unattainable residual oil can be produced with the injection of CO2 that has been captured at power stations or other large industrial emitters. Not only could this process produce incremental oil from a maturing basin, reducing imports, it also has the capability to store large volumes of CO2 which can offset the emissions of additional carbon produced. Around the world oil production from mature basins is in decline and production from UK oil fields peaked in 1998. Other basins around the world have a similar story. Although in the UK a number of tax regimes, such as 'brown field allowances' and 'new field allowances' have been put in place to re-encourage investment, it is recognised that the majority of large discoveries have already been made. However, as a nation our demand for oil remains high and in the last decade imports of crude oil have been steadily increasing. The UK is dependent on crude oil for transport and feedstock for chemical and plastics production. Combined with the necessity to provide energy security, there is a demand to re-assess the potential for CO2 Enhanced Oil Recovery (CO2-EOR) in the UK offshore. Residual oil zones (ROZ) exist where one of a number of natural conditions beyond normal capillary forces have caused the geometry of a field's oil column to be altered after filling [1]. When this re-structuring happens the primary interest to the hydrocarbon industry has in the past been in where the mobile oil has migrated to. However it is now considered that significant oil resource may exist in the residual zone play where the main oil column has been displaced. Saturations within this play are predominantly close to residual saturation (Sr) and would be similar to that of a water-flooded field [2]. Evidence from a number of hydrocarbon fairways shows that, under certain circumstances, these residual zones in US fields are comparable in thickness to the

Hydrocracking of atmospheric distillable residue of Mongolian oil

Directory of Open Access Journals (Sweden)

Ts Tugsuu

2014-09-01

Full Text Available Many catalytic processes to refine heavy part of crude oil have attracted much interest due to declining reserves of light crude oils. This study focused on hydrocracking process of atmospheric distillable residue of Mongolian crude oil in the first time compared to those of other countries. Residue samples were hydrocracked with a commercial catalyst at 450°C, 460°C, 470°C for 2 h under hydrogen pressure of 10 MPa. The amount of residual fraction (350°Cresidue from Tamsagbulag crude oil. When the ME-AR was hydrocracked, the high consumption of hydrogen was related to the lowest H/C atomic ratio of feed atmospheric residue. The amount of liquid fractions (BP<350°C including gaseous products increased from 45.4wt% to 89.2wt%, when the reaction temperature increased from 450°C to 470°C. The highest yield of the middle fraction for each sample was observed at temperature of 460°C. On the other hand, the effect of temperature on the yield of middle fraction was not so high as compared with the yields of other fractions. The contents of n-paraffins on midlle and heavy fractions of TB-AR, DQ-AR were similar, but ME-AR’s was around 2 times lower than other after hydrocracking runs.DOI: http://dx.doi.org/10.5564/mjc.v12i0.166 Mongolian Journal of Chemistry Vol.12 2011: 24-28 

Utilization of oil palm tree residues to produce bio-oil and bio-char via pyrolysis

International Nuclear Information System (INIS)

Abnisa, Faisal; Arami-Niya, Arash; Wan Daud, W.M.A.; Sahu, J.N.; Noor, I.M.

2013-01-01

Highlights: • About 14.72% of the total landmass in Malaysia was used for oil palm plantations. • Oil palm tree residues were pyrolyzed to produce bio-oil and bio-char. • The process was performed at a temperature of 500 °C and reaction time of 60 min. • Characterization of the products was performed. - Abstract: Oil palm tree residues are a rich biomass resource in Malaysia, and it is therefore very important that they be utilized for more beneficial purposes, particularly in the context of the development of biofuels. This paper described the possibility of utilizing oil palm tree residues as biofuels by producing bio-oil and bio-char via pyrolysis. The process was performed in a fixed-bed reactor at a temperature of 500 °C, a nitrogen flow rate of 2 L/min and a reaction time of 60 min. The physical and chemical properties of the products, which are important for biofuel testing, were then characterized. The results showed that the yields of the bio-oil and bio-char obtained from different residues varied within the ranges of 16.58–43.50 wt% and 28.63–36.75 wt%, respectively. The variations in the yields resulted from differences in the relative amounts of cellulose, hemicellulose, lignin, volatiles, fixed carbon, and ash in the samples. The energy density of the bio-char was found to be higher than that of the bio-oil. The highest energy density of the bio-char was obtained from a palm leaf sample (23.32 MJ/kg), while that of the bio-oil was obtained from a frond sample (15.41 MJ/kg)

Radiation processing studies on residual fractions of Olowi petroleum crude oil

International Nuclear Information System (INIS)

Sarfo, A.K.

2011-01-01

Residual fuel oil is an inexpensive boiler fuel that can replace diesel in some industrial boilers. The viscous waxy nature of residual fuel oil makes it very difficult to use in industries where fuel storage tanks have no heating elements to keep the fuel at temperatures at which it would easily flow. Irradiation is currently being studied as a cost effective means of cracking heavy petroleum crude oil into lighter and more valuable products. Research has shown that irradiation can replace the conventional methods of cracking petroleum with economical benefits. Gamma radiation from a cobalt-60 source was applied to the residue obtained after refining crude oil in this research study, with the intention of causing a similar cracking phenomenon. The main objective of the study was to evaluate the possibility of using gamma radiation to reduce the viscosity of residual fractions of crude oil used as residual fuel oil. This was done by exposing samples of residual fuel oil in glass jars to 9 different doses of gamma radiation, at room temperature and an elevated temperature of 60 degrees Celsius to determine and quantify the effect of radiation on residual fuel oil obtained from the Tema Oil Refinery. The pour points of the irradiated samples were not affected by radiation doses up to 200 kGy while the changes in viscosity for irradiation at room temperature were not significant. Irradiation at 60 degrees Celsius induced a small but significant increase in viscosity at 1 kGy and 200 kGy absorbed doses of irradiation. Irradiation fuels were stable in relation to viscosity, density and pour point over a period of 20 days after exposure. The flash point of irradiated samples, however, decreased by 5.26, 10.53 and 11.34% for 30, 50 and 80 kGy absorbed doses of radiation respectively. Cumulative and continuous doses gave similar results for pour point, density, viscosity and flash point measurements up to 50 kGy. Comparative cost analysis of methods used in maintaining low

Method of removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues

Energy Technology Data Exchange (ETDEWEB)

Palmquist, F T.E.

1949-09-08

A method is described for removing paraffin from mineral oils, shale oils, tar oils, and their fractions or residues by centrifuging in the presence of oil-dissolving and paraffin-precipitating solvents, by which the precipitated paraffin is made to pass through an indifferent auxiliary liquid, in which a removal of oil takes place, characterized in that as auxiliary liquid is used a liquid or mixture of liquids whose surface tension against the oil solution is sufficiently low for the paraffin to pass the layer of auxiliary liquid in the form of separate crystals.

Acephate and buprofezin residues in olives and olive oil.

Science.gov (United States)

Cabras, P; Angioni, A; Garau, V L; Pirisi, F M; Cabitza, F; Pala, M

2000-10-01

Field trials were carried out to study the persistence of acephate and buprofezin on olives. Two cultivars, pizz'e carroga and pendolino, with very large and small fruits respectively were used. After treatment, no difference was found between the two pesticide deposits on the olives. The disappearance rates, calculated as pseudo first order kinetics, were similar for both pesticides (on average 12 days). Methamidophos, the acephate metabolite, was always present on all olives, and in some pendolino samples it showed higher residues than the maximum residue limit (MRL). During washing, the first step of olive processing, the residue level of both pesticides on the olives did not decrease. After processing of the olives into oil, no residues of acephate or methamidophos were found in the olive oil, while the residues of buprofezin were on average four times higher than on olives.

Efficiency of the refining processes in removing 14C-dichlorvos residues in soybean oil

International Nuclear Information System (INIS)

Soliman, S.M.

2006-01-01

Crude soybean oil extracted from grains treated with 14 C-dichlorvos at a dose 24 mg insecticide / kg seeds and stored for 30 weeks was subjected to different refining processes such as alkali treatment, bleaching, winterization and deodorization. The effect of the refining processes on the nature and magnitude of the originally present residues was investigated. The insecticide residues in crude oil and cake amounted to 9.5% and 55% , respectively, of original residues inside the seeds. Extraction of the seeds with hexane gave crude oil with 9.5 % of original residues in seeds. The l4 C-activity in the crude stored Soya beans oil could be reduced by about 82% of radioactivity originally present in crude oil eliminated by simulated commercial processes locally used for oil refining. A high percentage of the residues (50-55%) were eliminated during alkali treatment and bleaching. Refining of soybeans oil fortified with '1 4 C-dichlorovos. The final refined oil had only 13% of the radioactivity originally present, mainly in the form of dichlorvos, dimethyl and monomethyl phosphate in addition to desmethyl dichlorvos in oil with aged residues

Biodiesel production from residual oils recovered from spent bleaching earth

International Nuclear Information System (INIS)

Huang, Yi-Pin; Chang, James I.

2010-01-01

This work was to study technical and economic feasibilities of converting residual oils recovered from spent bleaching earth generated at soybean oil refineries into useable biodiesel. Experimental results showed that fatty acids in the SBE residual oil were hexadecenoic acid (58.19%), stearic acid (21.49%) and oleic acid (20.32%), which were similar to those of vegetable oils. The methyl ester conversion via a transesterification process gave a yield between 85 and 90%. The biodiesel qualities were in reasonable agreement with both EN 14214 and ASTM D6751 standards. A preliminary financial analysis showed that the production cost of biodiesel from SBE oils was significantly lower than the pre-tax price of fossil diesel or those made of vegetable oils or waste cooking oils. The effects of the crude oil price and the investment on the production cost and the investment return period were also conducted. The result showed that the investment would return faster at higher crude oil price. (author)

The Effect of Processing on 14C- Chlofenvinphos Residues in Maize Oil and Bioavailability of its Cake Residues on Rats

International Nuclear Information System (INIS)

Mahdy, F.; El-Maghraby, S.

2008-01-01

Maize seed obtained from 14 C-chlofenvinphos treated plants contained 0.12 % of the applied dose. The insecticide residues in crude oil, methanol and coke amounted to 10 %, 6 % and 69 %, respectively of original residues inside the seeds.The 14 C activity in the crude oil could be a gradual reduced by the refining processes. The alkali treatment and bleaching steps are more effective steps in the refining processes remove about (63 %). The refined oil contained only about 17 % of the 14 C-residues originally present. The major residues in processed oil contain parent compound, in addition to five metabolites of the insecticide. When rats fed the extracted seeds (cake), the bound residues were found to be considerably bioavailable. After feeding rats for 5 days with the cake, a substantial amount of 14 C-residues was eliminated in the urine (59.5 %), while about 20 % was excreted in the feces. About 15 % of the radioactivity was distribution among various organs

On the relation of earthquake stress drop and ground motion variability

Science.gov (United States)

Oth, Adrien; Miyake, Hiroe; Bindi, Dino

2017-07-01

One of the key parameters for earthquake source physics is stress drop since it can be directly linked to the spectral level of ground motion. Stress drop estimates from moment corner frequency analysis have been shown to be extremely variable, and this to a much larger degree than expected from the between-event ground motion variability. This discrepancy raises the question whether classically determined stress drop variability is too large, which would have significant consequences for seismic hazard analysis. We use a large high-quality data set from Japan with well-studied stress drop data to address this issue. Nonparametric and parametric reference ground motion models are derived, and the relation of between-event residuals for Japan Meteorological Agency equivalent seismic intensity and peak ground acceleration with stress drop is analyzed for crustal earthquakes. We find a clear correlation of the between-event residuals with stress drops estimates; however, while the island of Kyushu is characterized by substantially larger stress drops than Honshu, the between-event residuals do not reflect this observation, leading to the appearance of two event families with different stress drop levels yet similar range of between-event residuals. Both the within-family and between-family stress drop variations are larger than expected from the ground motion between-event variability. A systematic common analysis of these parameters holds the potential to provide important constraints on the relative robustness of different groups of data in the different parameter spaces and to improve our understanding on how much of the observed source parameter variability is likely to be true source physics variability.

Ultrastructural effects of silicone oil on the clear crystalline lens of the human eye.

Science.gov (United States)

Soliman, Wael; Sharaf, Mohamed; Abdelazeem, Khaled; El-Gamal, Dalia; Nafady, Allam

2018-03-01

To evaluate light and electron microscopic changes of the anterior capsule and its epithelium after clear lens extraction of vitrectomized myopic eyes with silicone oil tamponade. This prospective, controlled, non-randomized, interventional study included 20 anterior lens capsular specimens that were excised during combined clear lens extraction and silicone oil removal from previously vitrectomized highly myopic patients with silicone oil tamponade for previous retinal detachment surgeries. The specimens were examined via light microscopy and electron microscopy and compared with 20 anterior capsule specimens removed during clear lens extraction of non-vitrectomized highly myopic eyes. Light microscopic examination of clear lens anterior capsule specimens of vitrectomized myopic eyes filled with silicone oil showed relatively more flat cells with irregular outline of lens' epithelial cells with wide intercellular spaces, deeply stained nuclei, and multiple intracytoplasmic vacuoles. Scanning electron microscopy revealed collagenous surfaces filled with multiple pits, depressions, and abnormal deposits. Transmission electron microscopy revealed lens epithelial cells with apoptotic changes, many cytoplasmic vacuoles, and filopodia-like protrusions between lens epithelial cells and the capsule. Epithelial proliferation and multilayering were also observed. silicone oil may play a role in the development of apoptotic and histopathological changes in clear lens epithelial cells. Clarity of the lens at the time of silicone oil removal does not indicate an absence of cataractous changes. We found justification of combined clear lens extraction and silicone oil removal or combined phacovitrectomy when silicone oil injection is planned, but further long-term studies with larger patient groups are required.

Assessing food allergy risks from residual peanut protein in highly refined vegetable oil

NARCIS (Netherlands)

Blom, W.M.; Kruizinga, A.G.; Rubingh, C.M.; Remington, B.C.; Crevel, R.W.R.; Houben, G.F.

2017-01-01

Refined vegetable oils including refined peanut oil are widely used in foods. Due to shared production processes, refined non-peanut vegetable oils can contain residual peanut proteins. We estimated the predicted number of allergic reactions to residual peanut proteins using probabilistic risk

Effect of commercial processing procedures on 14C-LINDANE residues in corn oil

International Nuclear Information System (INIS)

Soliman, S.M.

2006-01-01

At blooming, maize plants were sprayed twice, 23 days apart, at a dose of 22 mg equivalent to 5 μCi/ plant. At post harvest, maize seeds had a radioactivity corresponding to 0.36% of the applied dose. The insecticide residues in crude oil, cake and methanolic extract were amounted to 8 % and 60 % 5 % , respectively, of original residues inside the seeds.The 14 C-activity in the crude oil could be reduced by commercial processes locally used for refining. The refined oil had a residue level of about 0.7 ppm mainly in the form of unchanged lindane in addition to a number of chloro phenols as main metabolites. Refining of corn oil fortified with 14 C-lindane led to a high reduction of 14 C-lindane (88%). The refined oil contained a residue consisting lindane and its chloro phenols

PREPARATION OF VARIOUS TYPES OF PULP FROM OIL PALM LIGNOCELLULOSIC RESIDUES

Institute of Scientific and Technical Information of China (English)

RyoheiTanaka; LehCheuPeng; WanRosliWanDaud

2004-01-01

Oil palm, Elaeis Guineensis, (Figure 1) is one of the most important plants in Malaysia. It produces palm oil and palm kernel oil, which is widely being used in food and other industries such as detergents and cosmetics. Malaysia is the world's largest producer and exporter of the oil, so that the country's economy is very much dependent on these oil products. Although oil from the palm tree is an excellent product for the country, residues from oil palm have not been used sufficiently. In this 10-15 years, development in new technologies for utilizing this lignocellulosic waste is categorized as one of the most important issues in science policy of Malaysia. Here we would like to introduce recent situation of palm oil and oil palm lignocellulosic residues at the first part of this paper. In the second part, our recent studies on the preparation of pulps for different purposes will be summarized.

Oil price sinks drilling : exploration activity drops during third quarter

International Nuclear Information System (INIS)

Harrington, P.

1998-01-01

The decline in oil and gas exploration activity in Western Canada is discussed. In the third quarter of 1998, a total of 397 exploratory tests were reported compared to 768 during the same period in 1997. Low world oil prices are blamed as the cause of this decline. The declining exploration activity in 1998 was led by Alberta, with 289 new pool wildcat (NPW) announcements along with 25 new field wildcat (NFW) locations. Saskatchewan was in second place with 67 exploratory announcements, but compared to 329 in 1997, this represents an 80 per cent drop. British Columbia had a total of 15 exploratory wells resulting in three oil discoveries and 11 gas completions. Geological features, well characteristics and early production figures from several of the new wells in the Killam fields in southwest Saskatchewan were received special attention. 1 tab., 3 figs

Preparing hydraulic cement from oil-shale residue

Energy Technology Data Exchange (ETDEWEB)

1921-08-28

A process for preparation of hydraulic cement from oil-shale residue is characterized in that, as flux is used, rich-in-lime poor-in-sulfur portland-cement clinker, by which the usual gypsum addition, is avoided.

Effect of Refining Processes on Magnitude and Nature of Malathion and Carbofuran Residues in Cotton Seed Oil

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Farghaly, M.; Mahdy, F.

2005-01-01

Cotton seeds obtained from 14 C-carbofuran or 14 C-malathion-treated plants contained 0.25% and 0.11% of the originally applied radioactivity, respectively. The concentration of malathion residues in oil, methanol soluble and in the seed cake amounted to 0.94, 2.6 and 1.7 ppm, respectively. Commercial processing procedures led to a gradual decrease in the total amount of 14 C-residues in oils with aged residues as well as in oil fortified with the radiolabelled insecticides. The refined oil contained only about 20% of the 14 C-residues originally present. The major residue in processed oil contained malathion, malathion monocarboxylic acid and alpha-(O,O-dimethyl phosphorodithio)-propionic acid. The concentration of 14 C-carbofuran residues in cotton seed oil, methanol extract and cake was 1.7, 12.3 and 2.4 ppm, respectively. The main residues in the oil were carbofuran and its phenol. The methanol solubles contained conjugated metabolites, which upon hydrolysis gave 3-hydroxy-carbofuran as a major product. Refinement reduced the residue in oil to 0.26 ppm. The residue in refined oil contained carbofuran and carbofuran phenol as main constituents together with smaller amounts of 3-hydroxy- and 3-keto carbofuran

Effect of Water Cut on Pressure Drop of Oil (D130) -Water Flow in 4″Horizontal Pipe

Science.gov (United States)

Basha, Mehaboob; Shaahid, S. M.; Al-Hems, Luai M.

2018-03-01

The oil-water flow in pipes is a challenging subject that is rich in physics and practical applications. It is often encountered in many oil and chemical industries. The pressure gradient of two phase flow is still subject of immense research. The present study reports pressure measurements of oil (D130)-water flow in a horizontal 4″ diameter stainless steel pipe at different flow conditions. Experiments were carried out for different water cuts (WC); 0-100%. Inlet oil-water flow rates were varied from 4000 to 8000 barrels-per-day in steps of 2000. It has been found that the frictional pressure drop decreases for WC = 0 - 40 %. With further increase in WC, friction pressure drop increases, this could be due to phase inversion.

Experimental investigation and correlation of two-phase frictional pressure drop of R410A-oil mixture flow boiling in a 5 mm microfin tube

Energy Technology Data Exchange (ETDEWEB)

Ding, Guoliang; Hu, Haitao; Huang, Xiangchao [Institute of Refrigeration and Cryogenics, Shanghai Jiaotong University, Shanghai 200240 (China); Deng, Bin [Institute of Heat Transfer Technology, Golden Dragon Precise Copper Tube Group Inc., Shanghai 200135 (China); Gao, Yifeng [International Copper Association, Shanghai Office, Shanghai 200020 (China)

2009-01-15

This study presents experimental two-phase frictional data for R410A-oil mixture flow boiling in an internal spiral grooved microfin tube with outside diameter of 5 mm. Experimental parameters include the evaporation temperature of 5 C, the mass flux from 200 to 400 kg m{sup -2} s{sup -1}, the heat flux from 7.46 to 14.92 kW m{sup -2}, the inlet vapor quality from 0.1 to 0.8, and nominal oil concentration from 0 to 5%. The test results show that the frictional pressure drop of R410A initially increases with vapor quality and then decreases, presenting a local maximum in the vapor quality range between 0.7 and 0.8; the frictional pressure drop of R410A-oil mixture increases with the mass flux, the presence of oil enhances two-phase frictional pressure drop, and the effect of oil on frictional pressure drop is more evident at higher vapor qualities where the local oil concentrations are higher. The enhanced factor is always larger than unity and increases with nominal oil concentration at a given vapor quality. The range of the enhanced factor is about 1.0-2.2 at present test conditions. A new correlation to predict the local frictional pressure drop of R410A-oil mixture flow boiling inside the internal spiral grooved microfin tube is developed based on local properties of refrigerant-oil mixture, and the measured local frictional pressure drop is well correlated with the empirical equation proposed by the authors. (author)

Rhizosphere biodegradation of xenobiotics: Microbiological study of a rice field polluted by oil refinery residues

Energy Technology Data Exchange (ETDEWEB)

Rasolomanana, J.L.; Balandreau, J.

1987-07-01

A rice field had been studied in which the disposal of oil residues from a refinery plant seemed to improve rice growth and soil N content. To check the hypothesis that nitrogen fixation by oil-adapted bacteria could explain this observation we isolated and studied dominant diazotrophic bacteria from the rhizosphere of an actively N/sub 2/-fixing rice plant growing on the polluted soil; for this purpose we used an axenic plant as an enrichment step. The rhizosphere did not contain more than 10/sup 5/ N/sub 2/-fixing bacteria per g dry soil, essentially Bacillus polymyxa; one of the isolates, strain R3 could grow and reduce C/sub 2/H/sub 2/ on oil residues only in the presence of glucose or of exudates from an axenic plant (spermosphere model); the presence of R3 diminished the inhibition of rice growth due to the oil residues; R3 nitrogenase activity in the rhizosphere of rice was increased in the presence of these residues. This cometabolism of oil residues in the presence of exudates and their stimulating effect on N/sub 2/ fixation provide a likely explanation for observed positive effects of the disposal of oil residues on arable lands, and are conducive to the hypothesis that rhizosphere cometabolism could greatly enhance soil organic matter turn over and humification rates.

Production of petroleum bitumen by oxidation of heavy oil residue with sulfur

Science.gov (United States)

Tileuberdi, Ye.; Akkazyn, Ye. A.; Ongarbayev, Ye. K.; Imanbayev, Ye. I.; Mansurov, Z. A.

2018-03-01

In this paper production of bitumen adding elemental sulfur at oxidation of oil residue are investigated. The objects of research were distilled residue of Karazhanbas crude oil and elemental sulfur. These oil residue characterized by a low output of easy fractions and the high content of tar-asphaltene substances, therefore is the most comprehensible feedstock for producing bitumen. The sulfur is one of the oil product collected in oil extraction regions. Oxidation process of hydrocarbons carried out at temperatures from 180 up to 210 °С without addition of sulfur and with the addition of sulfur (5-10 wt. %) for 4 hours. At 200 °С oxidation of hydrocarbons with 5, 7 and 10 wt.% sulfur within 3-4 h allows receiving paving bitumen on the mark BND 200/300, BND 130/200, BN 90/130 and BN 70/30. Physical and mechanical characteristics of oxidation products with the addition of 5-7 wt. % sulfur corresponds to grade of paving bitumen BND 40/60. At the given temperature oxidized for 2.5-3 h, addition of 10 wt. % sulfur gave the products of oxidation describing on parameters of construction grades of bitumen (BN 90/10).

Residues in cottonseed oil and cake resulting from the combined application of DDT and dimethoate

International Nuclear Information System (INIS)

El Zorgani, G.A.; Ahmed, M.M.

1981-01-01

Cotton plants were treated with a combination of DDT and dimethoate under conditions of local agricultural practice to study the fate and magnitude of both chemicals in the cottonseed and related products. GLC and nuclear (using 14 C-DDT) techniques were used. DDT residues in the crude oil averaged 0.115 mg/kg; mainly as p,p'-DDT while residues in the cake were not detected. Dimethoate and dimethoxon in the crude oil were 0.13 and 0.01 mg/kg respectively. The cake contained 0.14 mg/kg dimethoate and 0.01 mg/kg dimethoxon. By simulating commercial oil processing in the laboratory using 14 C-DDT fortified oil samples it was found that alkali treatment and bleaching removed only 7% of the total residue, while deodorization effected removal of 40-50% of the residue. (author)

Evaporation-triggered microdroplet nucleation and the four life phases of an evaporating Ouzo drop

Science.gov (United States)

Tan, Huanshu; Diddens, Christian; Lv, Pengyu; Kuerten, J. G. M.; Zhang, Xuehua; Lohse, Detlef

2016-01-01

Evaporating liquid droplets are omnipresent in nature and technology, such as in inkjet printing, coating, deposition of materials, medical diagnostics, agriculture, the food industry, cosmetics, or spills of liquids. Whereas the evaporation of pure liquids, liquids with dispersed particles, or even liquid mixtures has intensively been studied over the past two decades, the evaporation of ternary mixtures of liquids with different volatilities and mutual solubilities has not yet been explored. Here we show that the evaporation of such ternary mixtures can trigger a phase transition and the nucleation of microdroplets of one of the components of the mixture. As a model system, we pick a sessile Ouzo droplet (as known from daily life—a transparent mixture of water, ethanol, and anise oil) and reveal and theoretically explain its four life phases: In phase I, the spherical cap-shaped droplet remains transparent while the more volatile ethanol is evaporating, preferentially at the rim of the drop because of the singularity there. This leads to a local ethanol concentration reduction and correspondingly to oil droplet nucleation there. This is the beginning of phase II, in which oil microdroplets quickly nucleate in the whole drop, leading to its milky color that typifies the so-called “Ouzo effect.” Once all ethanol has evaporated, the drop, which now has a characteristic nonspherical cap shape, has become clear again, with a water drop sitting on an oil ring (phase III), finalizing the phase inversion. Finally, in phase IV, all water has evaporated, leaving behind a tiny spherical cap-shaped oil drop. PMID:27418601

Enhancement of recovery of residual oil using a biosurfactant slug ...

African Journals Online (AJOL)

Characterization of the biosurfactant extract revealed a mixture of glycolipid and phospholipid in a ratio of 3.35:1. The irreducible water saturation (Swi) and initial residual oil saturation (Sor) of the sand-pack were 0.280 ± 0.003 and 0.373 ± 0.006, respectively. Core flooding experiment showed that an optimum oil recovery ...

Biodiesel of distilled hydrogenated fat and biodiesel of distilled residual oil: fuel consumption in agricultural tractor

Energy Technology Data Exchange (ETDEWEB)

Camara, Felipe Thomaz da; Lopes, Afonso; Silva, Rouverson Pereira da; Oliveira, Melina Cais Jejcic; Furlani, Carlos Eduardo Angeli [Universidade Estadual Paulista (UNESP), Jaboticabal, SP (Brazil); Dabdoub, Miguel Joaquim [Universidade de Sao Paulo (USP), Ribeirao Preto (Brazil)

2008-07-01

Great part of the world-wide oil production is used in fry process; however, after using, such product becomes an undesirable residue, and the usual methods of discarding of these residues, generally contaminate the environment, mainly the rivers. In function of this, using oil and residual fat for manufacturing biodiesel, besides preventing ambient contamination, turning up an undesirable residue in to fuel. The present work had as objective to evaluate the fuel consumption of a Valtra BM100 4x2 TDA tractor functioning with methylic biodiesel from distilled hydrogenated fat and methylic biodiesel from distilled residual oil, in seven blends into diesel. The work was conducted at the Department of Agricultural Engineering, at UNESP - Jaboticabal, in an entirely randomized block statistical design, factorial array of 2 x 7, with three repetitions. The factors combinations were two types of methylic distilled biodiesel (residual oil and hydrogenated fat) and seven blends (B{sub 0}, B{sub 5}, B{sub 1}5, B{sub 2}5, B{sub 5}0, B{sub 7}5 and B{sub 1}00). The results had evidenced that additioning 15% of biodiesel into diesel, the specific consumption was similar, and biodiesel of residual oil provided less consumption than biodiesel from hydrogenated fat. (author)

Dual catalyst system for the hydrocracking of heavy oils and residues

Energy Technology Data Exchange (ETDEWEB)

Bellussi, G. [ENI S.p.A., San Donato Milanese (Italy)

2011-07-01

One of the major challenges for our and for the future generations is the development of a sustainable energy supply system based mainly on renewable sources with no environmental impact. This task is necessary to limit the negative effects of green-house gas on the hearth and to allows the forecasted population growth. However, it is not yet clear the time span needed to reach the objective. The total world energy consumption in 2008 amounted to 8428 Mtoe. In a reference scenario, this amount is expected to grow to 16790 Mtoe in 2030 and the contribution expected by sources, according to the International Energy Agency, will be: oil 29.8 %, coal 29.1 %, natural gas 21,2 %, nuclear 5.7 %, hydroelectric 2.4 %, others (Renewable and waste, geothermal, solar, wind, tide,..) [1]. This picture indicates that for several decades, we must still rely on fossil fuels, avoid running out of this precious energy reserves of our planet and reducing the environmental damage arising from their use. For these reason there is a growing need for the efficient upgrading of the heavy oil streams for a better utilization of every barrel of oil produced and for bringing to production also the huge reserves of unconventional fossil sources, such as the heavy oils and the tar sands. Since several years many companies have R and D project aimed to the conversion of heavy residues through a hydrocracking slurry technology, which, with respect to other competing technologies, such as those based on fixed or ebullated bed, can convert all the feedstock to distillates, avoiding the production of fuel oil or coke. In this lecture the advancement in this area will be presented and discussed, highlighting the potentiality offered by the improvement of the catalyst system. (orig.)

Drop Hammer Tests with Three Oleo Strut Models and Three Different Shock Strut Oils at Low Temperatures

Science.gov (United States)

Kranz, M

1954-01-01

Drop hammer tests with different shock strut models and shock strut oils were performed at temperatures ranging to -40 C. The various shock strut models do not differ essentially regarding their springing and damping properties at low temperatures; however, the influence of the different shock strut oils on the springing properties at low temperatures varies greatly.

PREPARATION OF VARIOUS TYPES OF PULP FROM OIL PALM LIGNOCELLULOSIC RESIDUES

Institute of Scientific and Technical Information of China (English)

Ryohei Tanaka; Leh Cheu Peng; Wan Rosli Wan Daud

2004-01-01

@@ INTRODUCTION Oil palm, Elaeis Guineensis, (Figure 1) is one of the most important plants in Malaysia. It produces palm oil and palm kernel oil, which is widely being used in food and other industries such as detergents and cosmetics. Malaysia is the world′s largest producer and exporter of the oil, so that the country′s economy is very much dependent on these oil products. Although oil from the palm tree is an excellent product for the country, residues from oil palm have not been used sufficiently. In this 10～15 years, development in new technologies for utilizing this lignocellulosic waste is categorized as one of the most important issues in science policy of Malaysia.

proximate and ultimate analysis of fuel pellets from oil palm residues

African Journals Online (AJOL)

HOD

Keywords: Oil Palm Residues, Fuel Pellets, Proximate Analysis, Ultimate Analysis. 1. INTRODUCTION ... Pelletizing of this biomass resources into pellets is a way of ensuring a ... demand for pellets [3], and alternative feed-stocks such as palm kernel ... agro-residues, selection of the best pellets has to be made based on ...

Decomposition of residual oil by large scale HSC plant

Energy Technology Data Exchange (ETDEWEB)

Washimi, Koichi; Ogata, Yoshitaka; Limmer, H.; Schuetter, H. (Toyo Engineering Corp., funabashi, Japan VEB Petrolchemisches Kombinat Schwedt, Schwedt (East Germany))

1989-07-01

Regarding large scale and high decomposition ratio visbreaker HSC, characteristic points and operation conditions of a new plant in East Germany were introduced. As for the characteristics of the process, high decomposition ratio and stable decpmposed oil, availability of high sulfur content oil or even decomposed residuum of visbreaker, stableness of produced light oil with low content of unsaturated components, low investment with low running cost, were indicated. For the realization of high decomposition ratio, designing for suppressing the decomposition in heating furnace and accelaration of it in soaking drum, high space velocity of gas phase for better agitation, were raised. As the main subject of technical development, design of soaking drum was indicated with main dimensions for the designing. Operation conditions of the process in East Germany using residual oil supplied from already working visbreaker for USSR crude oil were introduced. 6 refs., 4 figs., 2 tabs.

Fabrication of superhydrophobic cotton textiles for water-oil separation based on drop-coating route.

Science.gov (United States)

Zhang, Ming; Wang, Chengyu; Wang, Shuliang; Li, Jian

2013-08-14

In the present study, we are so excited to report a simple drop-coating method for fabricating the superhydrophobic cotton textiles which can remove the water in oil (or the oil in water). It is confirmed that the superhydrophobic composite thin film containing modified-ZnO nanoparticles and polystyren (PS) has been successfully fabricated on the cotton textiles surface by a single-step procedure, and the superhydrophobic cotton textiles displays an excellent property in water-oil separation which is rarely put forward and studied. The static water contact angle on the superhydrophobic cotton sample surface arranges from 153° to 155°, and stays almost the same after exposure to ambient air or immersion in the corrosive liquids and oil, indicating the considerable range of potential applications for the superhydrophobic cotton textiles fabricated by this simple method. Copyright © 2013 Elsevier Ltd. All rights reserved.

Soy Sauce Residue Oil Extracted by a Novel Continuous Phase Transition Extraction under Low Temperature and Its Refining Process.

Science.gov (United States)

Zhao, Lichao; Zhang, Yong; He, Liping; Dai, Weijie; Lai, Yingyi; Yao, Xueyi; Cao, Yong

2014-04-09

On the basis of previous single-factor experiments, extraction parameters of soy sauce residue (SSR) oil extracted using a self-developed continuous phase transition extraction method at low temperature was optimized using the response surface methodology. The established optimal conditions for maximum oil yield were n-butane solvent, 0.5 MPa extraction pressure, 45 °C temperature, 62 min extraction time, and 45 mesh raw material granularity. Under these conditions, the actual yield was 28.43% ± 0.17%, which is relatively close to the predicted yield. Meanwhile, isoflavone was extracted from defatted SSR using the same method, but the parameters and solvent used were altered. The new solvent was 95% (v/v) ethanol, and extraction was performed under 1.0 MPa at 60 °C for 90 min. The extracted isoflavones, with 0.18% ± 0.012% yield, mainly comprised daidzein and genistein, two kinds of aglycones. The novel continuous phase transition extraction under low temperature could provide favorable conditions for the extraction of nonpolar or strongly polar substances. The oil physicochemical properties and fatty acids compositions were analyzed. Results showed that the main drawback of the crude oil was the excess of acid value (AV, 63.9 ± 0.1 mg KOH/g) and peroxide value (POV, 9.05 ± 0.3 mmol/kg), compared with that of normal soybean oil. However, through molecular distillation, AV and POV dropped to 1.78 ± 0.12 mg KOH/g and 5.9 ± 0.08 mmol/kg, respectively. This refined oil may be used as feedstuff oil.

Effect of oil refining processes on 14 C-tetrachlorvinphos residues in soya bean oil

International Nuclear Information System (INIS)

Farghaly, M.; Zayed, S.M.A.D.

1986-01-01

Crude soya bean oil extracted from grains treated with 14 C-tetrachlorvinphos and stored for 30 weeks was subjected to different refining processes. The effect of commercial refining processes, namely: alkali treatment, bleaching, winterization and deodorization on the nature and magnitude of the originally present residues was investigated. A high percentage (52%) of the residues was eliminated during alkali neutralization. No potentially toxic materials were detected among the identified degradation products. The obtained data showed that the ultimate degradation products were dimethyl phosphate and mono methyl phosphate.2 tab.,2 scheme

MODEL FOR THE CORRECTION OF THE SPECIFIC GRAVITY OF BIODIESEL FROM RESIDUAL OIL

Directory of Open Access Journals (Sweden)

Tatiana Aparecida Rosa da Silva

2013-06-01

Full Text Available Biodiesel is a important fuel with economic benefits, social and environmental. The production cost of the biodiesel can be significantly lowered if the raw material is replaced by a alternative material as residual oil. In this study, the variation of specific gravity with temperature increase for diesel and biodiesel from residual oil obtained by homogeneous basic catalysis. All properties analyzed for biodiesel are within specification Brazil. The determination of the correction algorithm for the specific gravity function of temperature is also presented, and the slope of the line to diesel fuel, methylic biodiesel (BMR and ethylic biodiesel (BER from residual oil were respectively the values -0.7089, -0.7290 and -0.7277. This demonstrates the existence of difference of the model when compared chemically different fuels, like diesel and biodiesel from different sources, indicating the importance of determining the specific algorithm for the operations of conversion of volume to the reference temperature.

Process and catalysis for hydrocracking of heavy oil and residues

Energy Technology Data Exchange (ETDEWEB)

Morel, F.; Kressmann, S. [Centre d' Etudes et de developpement Indutriel ' Rene Navarre' , Vernaison (France); Harle, V.; Kasztelan, S. [Division Cinetique et Catalyse, Rueil-Malmaison (France)

1997-07-01

Atmospheric or vacuum residue can be converted into valuable distillates using reaction temperature, high hydrogen pressure and low contact time hydroprocessing units. Various residue hydrocracking processes are now commercially employed using fixed bed, moving bed or ebullated bed reactors. The choice of process type depends mainly on the amount of metals and asphaltenes in the feed and on the level of conversion required. Various improvements have been introduced in the last decade to increase run length, conversion level, products qualities and stability of the residual fuel. These improvements include on stream catalysts replacement systems, swing reactors, improved feed distribution, guard bed materials limiting pressure drop, coke resistant catalysts, complex association of catalysts using particle size, activity and pore size grading. Further improvement of the resistance of catalysts to deactivation by coke and metal deposits and of the hydrodenitrogenation activity are two major challenges for the development of new residue hydrocracking catalysts and processes. 29 refs.

Catalyst systems in the production of biodiesel from residual oil; Sistemas cataliticos na producao de biodiesel por meio de oleo residual

Energy Technology Data Exchange (ETDEWEB)

Souza, Carlos Alexandre de [Universidade Federal de Itajuba (UNIFEI), MG (Brazil)

2006-07-01

The vegetable oils and fat animals appear like an alternative for substitution the diesel oil in ignition engines for compression. Submitting the oil on transesterification reaction, we obtain a fuel with same characteristics as diesel, called biodiesel. Generally, 85 per cent of biodiesel cost is from the oil production. Through transesterification vegetable oil can be transformed in a mixture of esters of fatty acids. The residual oil from frying has been used as a possibility of raw materials of biodiesel, due to its easy acquisition and the viability of not being discarded as waste. (author)

Search for free fractional electric charge elementary particles using an automated millikan oil drop technique

Science.gov (United States)

Halyo; Kim; Lee; Lee; Loomba; Perl

2000-03-20

We have carried out a direct search in bulk matter for free fractional electric charge elementary particles using the largest mass single sample ever studied-about 17.4 mg of silicone oil. The search used an improved and highly automated Millikan oil drop technique. No evidence for fractional charge particles was found. The concentration of particles with fractional charge more than 0. 16e ( e being the magnitude of the electron charge) from the nearest integer charge is less than 4.71x10(-22) particles per nucleon with 95% confidence.

Development of a field testing protocol for identifying Deepwater Horizon oil spill residues trapped near Gulf of Mexico beaches

Science.gov (United States)

Han, Yuling

2018-01-01

The Deepwater Horizon (DWH) accident, one of the largest oil spills in U.S. history, contaminated several beaches located along the Gulf of Mexico (GOM) shoreline. The residues from the spill still continue to be deposited on some of these beaches. Methods to track and monitor the fate of these residues require approaches that can differentiate the DWH residues from other types of petroleum residues. This is because, historically, the crude oil released from sources such as natural seeps and anthropogenic discharges have also deposited other types of petroleum residues on GOM beaches. Therefore, identifying the origin of these residues is critical for developing effective management strategies for monitoring the long-term environmental impacts of the DWH oil spill. Advanced fingerprinting methods that are currently used for identifying the source of oil spill residues require detailed laboratory studies, which can be cost-prohibitive. Also, most agencies typically use untrained workers or volunteers to conduct shoreline monitoring surveys and these worker will not have access to advanced laboratory facilities. Furthermore, it is impractical to routinely fingerprint large volumes of samples that are collected after a major oil spill event, such as the DWH spill. In this study, we propose a simple field testing protocol that can identify DWH oil spill residues based on their unique physical characteristics. The robustness of the method is demonstrated by testing a variety of oil spill samples, and the results are verified by characterizing the samples using advanced chemical fingerprinting methods. The verification data show that the method yields results that are consistent with the results derived from advanced fingerprinting methods. The proposed protocol is a reliable, cost-effective, practical field approach for differentiating DWH residues from other types of petroleum residues. PMID:29329313

Development of a field testing protocol for identifying Deepwater Horizon oil spill residues trapped near Gulf of Mexico beaches.

Science.gov (United States)

Han, Yuling; Clement, T Prabhakar

2018-01-01

The Deepwater Horizon (DWH) accident, one of the largest oil spills in U.S. history, contaminated several beaches located along the Gulf of Mexico (GOM) shoreline. The residues from the spill still continue to be deposited on some of these beaches. Methods to track and monitor the fate of these residues require approaches that can differentiate the DWH residues from other types of petroleum residues. This is because, historically, the crude oil released from sources such as natural seeps and anthropogenic discharges have also deposited other types of petroleum residues on GOM beaches. Therefore, identifying the origin of these residues is critical for developing effective management strategies for monitoring the long-term environmental impacts of the DWH oil spill. Advanced fingerprinting methods that are currently used for identifying the source of oil spill residues require detailed laboratory studies, which can be cost-prohibitive. Also, most agencies typically use untrained workers or volunteers to conduct shoreline monitoring surveys and these worker will not have access to advanced laboratory facilities. Furthermore, it is impractical to routinely fingerprint large volumes of samples that are collected after a major oil spill event, such as the DWH spill. In this study, we propose a simple field testing protocol that can identify DWH oil spill residues based on their unique physical characteristics. The robustness of the method is demonstrated by testing a variety of oil spill samples, and the results are verified by characterizing the samples using advanced chemical fingerprinting methods. The verification data show that the method yields results that are consistent with the results derived from advanced fingerprinting methods. The proposed protocol is a reliable, cost-effective, practical field approach for differentiating DWH residues from other types of petroleum residues.

AN ALTERNATIVE APPROACH TO THE USE OF HEAVY OIL RESIDUE

Directory of Open Access Journals (Sweden)

Eugene Dashut

2013-01-01

Full Text Available We consider an alternative approach to the existing oil refining, in which instead of a single priority that emerged in the traditional approach, we consider two: get the light component and a heavy residue used for the production of new construction materials.

Research within the coordinated programme on isotopic-tracer-aided studies of chemical residues in cotton seed, oil, feed and related products

International Nuclear Information System (INIS)

Qureshi, M.J.

1981-06-01

14 C-methyl and 14 C-ring-labelled carbaryl (1-naphthyl-N-methyl carbamate) were used to study the fate and magnitude of the insecticide in the plant and cotton seed products. Under conditions of actual agricultural practice, 0.08-0.09, 0.23-0.30 and 0.05 mg/kg of 14 C-residues were found in the seed, crude oil and cake respectively. In oil, the residue was resolved into 4 compounds, 2 identified as carbaryl and 1-naphthol. Residues from the soil did not exceed 0.3 mg/kg after the first week and declined to 0.1 mg/kg after 5 weeks. Parallel experiments were conducted under field conditions using 14 C-phenyl leptophos (4-bromo-2,5-dichlorophenyl methyl phenyl phosphorothioate). Leptophos residues were determined in the cotton seed products during 1975, 1976 and 1977, with mean values for leptophos residues in the cotton seed, crude oil and cake of 0.26, 1.10 and 0.07 mg/kg, respectively. Experiments with non-labelled monocrotophos [3-(dimethoxy phosphinyloxy)-N-methyl cis-crotonamide] gave residues of 0.30, 1.56 and 0.02 mg/kg in the seed, crude oil and cake, respectively. Carbaryl residues in two local maize varieties were determined by a colorimetric method. Cooking in aqueous, oil or aqueous-oil media led to 63-83% loss of carbaryl residues, after 30 minutes. Storage of corn oil for one year had essentially no effect on the concentration of carbaryl residues under laboratory conditions (presumably similar to regular storage conditions). An overall effect of simulated commercial processing procedures (saponification, deodorization and winterization) gave a loss of 70% of the original carbaryl in the oil. Commercial cooking procedures for national popular dishes resulted in near-complete elimination of carbaryl residues (up to 98%). Frying onions and potatoes in carbaryl-spiked corn oil for 3 min. up to 210 0 C resulted in 55-60% loss of the residue

Compositional changes of aromatic steroid hydrocarbons in naturally weathered oil residues in the Egyptian western desert

International Nuclear Information System (INIS)

Barakat, A.O.; Qian, Y.; Kim, M.; Kennicutt, M.C. II

2002-01-01

Aromatic steranes are geochemical markers that can be used to study the maturation of organic matter of sediments and to correlate crude oils and source rocks. In this study, naturally weathered oil residues from an arid waste disposal site in Al-Alamein, Egypt, were analyzed for monoaromatic and triaromatic steranes to show the usefulness of biomarker compounds in assessing changes in chemical composition during the degradation of oil residues that have been released onto terrestrial environments. Gas chromatography and mass spectrometry were used to characterize the individual aromatic compounds. Results indicate that triaromatic sterane distributions are similar in oil residues with varying extents of weathering. The distribution correlated with a fresh crude oil sample from Western Desert-sourced oil. Molecular ratios of triaromatic sterane compounds were found to be suitable for source identification. The major changes in chemical compositions resulting from the weathering of the oil included the depletion of short chain mono- and tri-aromatic steranes in extremely weathered samples. The results of the triaromatic sterane distribution correspond with weathering classifications based on the analyses of saturated and aromatic hydrocarbons and the ratios of n-alkanes, polycyclic aromatic hydrocarbons, and saturate biomarker compounds. 15 refs., 3 tabs., 3 figs

Asphalts tests using onshore drilling oil wells residues; Ensaios asfalticos utilizando residuos de perfuracao onshore

Energy Technology Data Exchange (ETDEWEB)

Lucena, Adriano Elisio de F.L.; Rodrigues, John Kennedy G.; Ferreira, Heber Carlos; Lucena, Leda Christiane de F.L. [Universidade Federal de Campina Grande (UFCG), PB (Brazil); Lucena, Luciana de F.L. [Faculdade de Ciencias Sociais Aplicada (FACISA), Campina Grande, PB (Brazil)

2008-07-01

The drilling cuttings are one of the residues produced by the oils industries in large amounts during the drilling of oil wells. An alternative of final disposal of the drilling cutting residue is its utilization in asphalt mixtures. Based on this alternative, it was realized chemical and granulometric analysis and tests (Marshall and indirect tensile strength), on the asphaltic mixture using the residue from the oil drilling wells (well: 1-POTI-4-RN, located at Governador DIX-Sept Rosado - RN - Brazil). The achieved results to Marshall test indicated that for the analyzed mixture, the ideal content of residue that can be incorporated to the asphaltic composition and attend at the DNIT-ES 31 (2006) is 5%. To the indirect tensile strength test, the results showed a strength value higher than the minimum limit requested by the DNIT (0,65 MPa). The achieved results indicated the possibility of the utilization of the drilling cuttings in asphaltic pavements as fine aggregate, obeying the percentage limits, as an alternative to the final disposal. (author)

Microbial Physiology of the Conversion of Residual Oil to Methane: A Protein Prospective

Science.gov (United States)

Morris, Brandon E. L.; Bastida-Lopez, Felipe; von Bergen, Martin; Richnow, Hans-Hermann; Suflita, Joseph M.

2010-05-01

Traditional petroleum recovery techniques are unable to extract the majority of oil in most petroliferous deposits. The recovery of even a fraction of residual hydrocarbon in conventional reserves could represent a substantive energy supply. To this end, the microbial conversion of residual oil to methane has gained increasing relevance in recent years [1,2]. Worldwide demand for methane is expected to increase through 2030 [3], as it is a cleaner-burning alternative to traditional fuels [4]. To investigate the microbial physiology of hydrocarbon-decomposition and ultimate methanogenesis, we initiated a two-pronged approach. First, a model alkane-degrading sulfate-reducing bacterium, Desulfoglaeba alkanexedens, was used to interrogate the predominant metabolic pathway(s) differentially expressed during growth on either n-decane or butyrate. A total of 81 proteins were differentially expressed during bacterial growth on butyrate, while 100 proteins were unique to the alkane-grown condition. Proteins related to alkylsuccinate synthase, or the homologous 1-methyl alkylsuccinate synthase, were identified only in the presence of the hydrocarbon. Secondly, we used a newly developed stable isotope probing technique [5] targeted towards proteins to monitor the flux of carbon through a residual oil-degrading bacterial consortium enriched from a gas-condensate contaminated aquifer [1]. Combined carbon and hydrogen stable isotope fractionation identified acetoclastic methanogenesis as the dominant process in this system. Such findings agree with the previous clone library characterization of the consortium. Furthermore, hydrocarbon activation was determined to be the rate-limiting process during the net conversion of residual oil to methane. References 1. Gieg, L.M., K.E. Duncan, and J.M. Suflita, Bioenegy production via microbial conversion of residual oil to natural gas. Appl Environ Micro, 2008. 74(10): p. 3022-3029. 2. Jones, D.M., et al., Crude-oil biodegradation via

Research on the porous flow of the mechanism of viscous-elastic fluids displacing residual oil droplets in micro pores

Science.gov (United States)

Dong, Guanyu

2018-03-01

In order to analyze the microscopic stress field acting on residual oil droplets in micro pores, calculate its deformation, and explore the hydrodynamic mechanism of viscous-elastic fluids displacing oil droplets, the viscous-elastic fluid flow equations in micro pores are established by choosing the Upper Convected Maxwell constitutive equation; the numerical solutions of the flow field are obtained by volume control and Alternate Direction Implicit methods. From the above, the velocity field and microscopic stress field; the forces acting on residual oil droplets; the deformations of residual oil droplets by various viscous-elastic displacing fluids and at various Wiesenberg numbers are calculated and analyzed. The result demonstrated that both the normal stress and horizontal force acting on the residual oil droplets by viscous-elastic fluids are much larger compared to that of inelastic fluid; the distribution of normal stress changes abruptly; under the condition of the same pressure gradient in the system under investigation, the ratio of the horizontal forces acting on the residual oil droplets by different displacing fluids is about 1:8:20, which means that under the above conditions, the driving force on a oil droplet is 20 times higher for a viscous-elastic fluid compared to that of a Newtonian Fluid. The conclusions are supportive of the mechanism that viscous-elastic driving fluids can increase the Displacement Efficiency. This should be of help in designing new chemicals and selecting Enhanced Oil Recovery systems.

Effect of capillary number on the oil recovery using oil-water emulsion injection in core flooding experiments

Energy Technology Data Exchange (ETDEWEB)

Guillen Nunez, Victor Raul; Carvalho, Marcio da Silveira [Pontifical Catholic University of Rio de Janeiro (PUC-Rio), RJ (Brazil). Dept. of Mechanical Engineering], E-mail: msn@puc-rio.br; Basante, Vladimir Alvarado [University of Wyoming, Laramie, WY (United States). Dept. of Chemical/Petroleum Engineering], E-mail: valvard@uwyo.edu

2010-07-01

The Water injection flooding is a common method to improve reservoir sweep and pressure maintenance. The heavy-oil-recovery efficiency is in part limited by the high water-to-oil mobility ratio. Several enhanced oil recovery methods are being developed as more efficient alternatives to water flooding. Dispersion injection, in particular oil-water emulsion injection, has been tried with relative success as an enhanced oil recovery method, but the technique is not fully developed or understood. If emulsion injection proves to be an effective EOR method, its use would bring the added benefit of disposing produced water with small oil content that could be modified to serve as the injected oil-water emulsion. The use of such methods requires a detailed analysis of the different flow regimes of emulsions through the porous space of a reservoir rock. If the drop size of the disperse phase is of the same order of magnitude as the pore size, the drops may agglomerate and partially block water flow through pores. This flow regime may be used to control the mobility of the injected liquid, leading to higher recovery factor. We have shown in recent experiments of oil displacement in a sandstone core that, the oil recovery factor could be raised from approximately 40 %, obtained with water injection only, up to approximately 75 % by alternating water and emulsion injection. Although these results clearly show the improvement in the recovery factor, the mechanisms responsible for the phenomenon have not been clearly elucidated. In this work, two sandstone cores were used to demonstrate the effect of flow rate (capillary number) on the mobility control by emulsion injection. Figure 1 shows a schematic representation of the experiment set-up. The experiments show that raising the flow rate by a factor of 10 (0.03 ml/min to 0.3 ml/min), the oil recovered factor decreases considerably. (author)

The Oil Drop Experiment: An Illustration of Scientific Research Methodology and its Implications for Physics Textbooks

Science.gov (United States)

Rodriguez, Maria A.; Niaz, Mansoor

2004-01-01

The objectives of this study are: (1) evaluation of the methodology used in recent search for particles with fractional electrical charge (quarks) and its implications for understanding the scientific research methodology of Millikan; (2) evaluation of 43 general physics textbooks and 11 laboratory manuals, with respect to the oil drop experiment,…

Improvement of Dune Sands by Residual Oil in Order to Use in Construction of Lagoons

Directory of Open Access Journals (Sweden)

Alborz Hajian nia

2011-10-01

Full Text Available This research which is based on experimental work, devoted to study the improvement and stabilization of dune sands in order to create strong layer and stabilize slope and floor construction of sewage Lagoons. Materials used stabilizing these soils are residual oil from the refinery. To confirm the effectiveness of the use of residual oil to improve the mechanical properties of the sand, various samples with different percentages were tested. In besides, the geotechnical and environmental tests were done. Results demonstrate that samples made with 5% oil have highest shear and unconfined compaction strength. It revealed that in compare with natural samples, cohesion and loading capacity highly increased and permeability decrease well. Percentage of fine aggregate, minerals and durability of oil in soil material were also investigated. Finally, effects of sewage on the samples were analyzed, and performance the oils were evaluated in order to use in lagoons.

γ-Oryzanol and tocopherol contents in residues of rice bran oil refining.

Science.gov (United States)

Pestana-Bauer, Vanessa Ribeiro; Zambiazi, Rui C; Mendonça, Carla R B; Beneito-Cambra, Miriam; Ramis-Ramos, Guillermo

2012-10-01

Rice bran oil (RBO) contains significant amounts of the natural antioxidants γ-oryzanol and tocopherols, which are lost to a large degree during oil refining. This results in a number of industrial residues with high contents of these phytochemicals. With the aim of supporting the development of profitable industrial procedures for γ-oryzanol and tocopherol recovery, the contents of these phytochemicals in all the residues produced during RBO refining were evaluated. The samples included residues from the degumming, soap precipitation, bleaching earth filtering, dewaxing and deodorisation distillation steps. The highest phytochemical concentrations were found in the precipitated soap for γ-oryzanol (14.2 mg g(-1), representing 95.3% of total γ-oryzanol in crude RBO), and in the deodorisation distillate for tocopherols (576 mg 100 g(-1), representing 6.7% of total tocopherols in crude RBO). Therefore, among the residues of RBO processing, the deodorisation distillate was the best source of tocopherols. As the soap is further processed for the recovery of fatty acids, samples taken from every step of this secondary process, including hydrosoluble fraction, hydrolysed soap, distillation residue and purified fatty acid fraction, were also analyzed. The distillation residue left after fatty acid recovery from soap was found to be the best source of γ-oryzanol (43.1 mg g(-1), representing 11.5% of total γ-oryzanol in crude RBO). Copyright © 2012 Elsevier Ltd. All rights reserved.

Gastric pH and residual volume after 1 and 2 h fasting time for clear fluids in children†.

Science.gov (United States)

Schmidt, A R; Buehler, P; Seglias, L; Stark, T; Brotschi, B; Renner, T; Sabandal, C; Klaghofer, R; Weiss, M; Schmitz, A

2015-03-01

Current guidelines suggest a fasting time of 2 h for clear fluids, which is often exceeded in clinical practice, leading to discomfort, dehydration and stressful anaesthesia induction to patients, especially in the paediatric population. Shorter fluid fasting might be a strategy to improve patient comfort but has not been investigated yet. This prospective clinical trial compares gastric pH and residual volume after 1 vs 2 h of preoperative clear fluid fasting. Children (1-16 yr, ASA I or II) undergoing elective procedures in general anaesthesia requiring tracheal intubation were randomized into group A with 60 min or B with 120 min preoperative clear fluid fasting. To determine gastric pH and residual volume, the gastric content was sampled in supine, left and right lateral patient position using an oro-gastric tube after intubation. Data are median (interquartile range) for group A or B (PPatient characteristic data were similar between the two groups, except for gender (46/33 males in group A/B; P=0.02). Despite significantly shorter fasting times for clear fluids in group A compared with group B (76/136 min; P<0.001), no significant difference was observed regarding gastric pH [1.43 (1.30-1.56)/1.44 (1.29-1.68), P=0.66] or residual volume [0.43 (0.21-0.84)/0.46 (0.19-0.78) ml kg(-1), P=0.47]. One hour clear fluid fasting does not alter gastric pH or residual volume significantly compared with 2 h fasting. The study was approved by the local ethics committee (KEK-ZH-Nr. 2011-0034) and registered with ClinicalTrials.gov (NCT01516775). © The Author 2014. Published by Oxford University Press on behalf of the British Journal of Anaesthesia. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Carbaryl and monocrotophos residues in cottonseed products. Part of a coordinated programme on isotopic tracer-aided studies of chemical residues in cotton seed, feed, oil and related products

International Nuclear Information System (INIS)

Pablo, F.E.

1981-03-01

Cotton plants of Deltapine variety were treated with carbaryl (naphthyl-1- 14 C), (6.7 mg/plant) three times at two week intervals. Seeds were collected at maturity and 14 C-residues were determined in the oil and cake by standard procedures. 14 C-carbaryl and/or metabolite residues were 0.42 and 0.15 mg/kg in the crude oil and cake respectively. Parallel studies were conducted with spectrophotometric techniques using p-nitrobenzene diazonium fluoborate as chromogenic agent. Applications were made three times at a rate of 14 mg/plant. Residues in the crude oil and cake were found to be 0.83 and 0.04 mg/kg respectively. The higher residue level in the oil - compared to the radiometric technique - probably relates to higher application rates. Cotton plants of Deltapine variety were treated with (N-methyl- 14 C) monocrotophos (0.09 mg/plant) three times at two week intervals, as recommended for agricultural practice. Seeds were collected at maturity and standard procedures for extraction, clean-up and paper and thin-layer chromatography were adopted for the ultimate determination of residues in seed, oil and cake. Parallel experiments, using spectrophotometric techniques, were made for comparison. 14 C-residues of monocrotophos and/or metabolites in cottonseed, crude oil and cake were found to be 0.06, 0.12 and 0.05 mg/kg respectively. Corresponding data obtained by non-nuclear techniques were 0.18, 0.42 and 0.15 mg/kg respectively. The discrepancy between the two sets of results may be related to different rates of application: 0.3 mg and 0.09 mg/plant for non-nuclear and radiometric techniques respectively. Among the major metabolites identified in the cottonseed were dimethyl phosphate and O-desmethyl monocrotophos. N-demethylated monocrotophos and sugar conjugates were also identified

Effect of inorganic chelate of zinc and restaurant residual oil added ...

African Journals Online (AJOL)

Jane

2011-08-01

Aug 1, 2011 ... residual oil added to feed mixture on the biochemical traits of thigh muscles in .... The basal diet (Soybean + corn); T2 = basal diet + 0% RRO + 50 mg/kg ZnO; T3 = basal ... fatty acids, using gas chromatography (AOAC, 1999).

Study on the reutilization of clear fracturing flowback fluids in surfactant flooding with additives for Enhanced Oil Recovery (EOR).

Science.gov (United States)

Dai, Caili; Wang, Kai; Liu, Yifei; Fang, Jichao; Zhao, Mingwei

2014-01-01

An investigation was conducted to study the reutilization of clear fracturing flowback fluids composed of viscoelastic surfactants (VES) with additives in surfactant flooding, making the process more efficient and cost-effective. The clear fracturing flowback fluids were used as surfactant flooding system with the addition of α-olefin sulfonate (AOS) for enhanced oil recovery (EOR). The interfacial activity, emulsification activity and oil recovery capability of the recycling system were studied. The interfacial tension (IFT) between recycling system and oil can be reduced by 2 orders of magnitude to 10(-3) mN/m, which satisfies the basic demand of surfactant flooding. The oil can be emulsified and dispersed more easily due to the synergetic effect of VES and AOS. The oil-wet surface of quartz can be easily converted to water-wet through adsorption of surfactants (VES/AOS) on the surface. Thirteen core plug flooding tests were conducted to investigate the effects of AOS concentrations, slug sizes and slug types of the recycling system on the incremental oil recovery. The investigations prove that reclaiming clear fracturing flowback fluids after fracturing operation and reuse it in surfactant flooding might have less impact on environment and be more economical.

Heating oil, distillates and residuals outlook

International Nuclear Information System (INIS)

Ervin, M.J.

2004-01-01

M.J. Ervin and Associates offers strategic planning support to the downstream petroleum industry in terms of price market monitoring, market analysis, media commentary and benchmarking of marketing operations. This presentation included graphs depicting supply and demand for heating oil distillates and residuals from the mid 1990s to 2004. It was noted that the long-term decline in residuals demand in the United States and Canada are due to environmental issues, the use of natural gas as an alternative, and the increasing complexity of refineries. Graphs depicting market impacts of refinery utilization and inventory trends showed that middle distillate production will increase at the expense of gasoline production. Middle distillates and gasoline markets will be more sensitive to supply disruptions, resulting in more frequent price spikes. Inventory trends indicate a greater reliance on product imports. The demand for heating fuel has stabilized due to the continued penetration of natural gas in eastern states and provinces. The demand for diesel fuel has growth 1.5 to 2 per cent while the demand for jet fuel has remained relatively flat and depends greatly on the growth of the gross national product (GNP). tabs., figs

Removal of emulsified oil in residual waters by means of dissolved air flotation

International Nuclear Information System (INIS)

Echeverri Londono, Carlos Alberto

1996-01-01

In this article is consigned a theoretical and experimental study on the treatment of industrial residual waters with emulsified oil, through the flotation process for dissolved air (FAD), changing some operation parameters and some importance topics, related with the process. The experimental results and the theoretical pattern, show that the removal of oil depends fundamentally on the chemical pretreatment. Efficiencies of removal of oil up of 99% they were obtained, using the dissolved air flotation with the help of coagulants

Characterization of residual biomass from the Arequipa region for the production of biofuels

Directory of Open Access Journals (Sweden)

María Laura Stronguiló Leturia

2015-12-01

Full Text Available The aim of this work is to select residual biomass from the Arequipa Region for the production of biofuels (biodiesel, bioethanol and biogas. In each case, the initial point is a matrix based on products with residual biomass available in the region, from the agricultural and livestock sectors, information that was obtained from the regional Management of Agriculture web site. Specific factors of the resudue that will be used as raw material for each biofuel production would be considered for the selection process. For the production of biodiesel it is necessary to start from the oil extracted from oilseeds. Regarding obtaining bioethanol, it requires that the residual biomass has high percent of cellulose. With regard to the generation of biogas, we will use animal droppings. Finally, the raw materials selected are: squash and avocado seeds for biodiesel, rice chaff and deseeded corncob for bioethanol and cow and sheep droppings for biogas

Processing and display of nuclear magnetism logging signals: application to residual oil determination

International Nuclear Information System (INIS)

Brown, R.J.S.; Neuman, C.H.

1980-01-01

A presentation is made of a series of computations and signal displays which help to show the nature of NML signals in general as well as to show the response to particular formation, hole, and tool conditions. Such processing of digitally recorded signals enables improved accuracy and bed resolution over that presented with the raw log. The treatment of drilling mud filtrate to eliminate NML signal from the brine phase in the invaded zone is described. Logs are shown as recorded before and after invasion of treated mud filtrate. This treatment causes the NML signal to correspond to residual oil only, enabling accurate and relatively inexpensive measurement of residual oil. 24 refs

Isolation of Indonesian Cananga Oil by Instantaneous Controled Pressure Drop: Influence of Processing Parameters on Compound Yields.

Czech Academy of Sciences Publication Activity Database

Kristiawan, M.; Sobolík, Václav; Al Haddad, M.; Allaf, K.

2007-01-01

Roč. 40, 11 (2007) , s. 1021-1029 ISSN 0021-9592. [IWPI2006. Kobe, 15.10.2006-18.10.2006] Institutional research plan: CEZ:AV0Z40720504 Keywords : cananga oil * instantaneous controlled pressure Drop * steam distillation Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 0.594, year: 2007

Effect of inorganic chelate of zinc and restaurant residual oil added ...

African Journals Online (AJOL)

Effect of inorganic chelate of zinc and restaurant residual oil added to feed mixture ... The interaction effects of RRO and ZnO did not result to a significant change in ... Therefore, the effects of RRO deteriorated the quality of meat by raising the ...

The effect of commercial processing procedures on 14C-carbendazim residues in soybean oil and tomato

International Nuclear Information System (INIS)

Peng Genyuan; Wang Huaguo; Qi Mengwen; Wang Fujun; Zhou Changjiu

1994-01-01

Under simulated agricultural practices, soybean plants were treated with 14 C-labelled carbendazim during the blooming stage. The residue in seeds was determined to be 0.067 ppm; corresponding to 0.076 ppm respectively. After subjecting the oil to degumming, alkali treatment, bleaching and deodorization, 53.7% of original radioactivity was removed. Deodorization was the most effect process, removing about 20% of the residue. The concentration of residues in the deodorized oil decreased about 30%. In soybean seed and cake, the residue was mainly present as carbendazim, the concentration of the other metabolites did not exceed 30% of the residue. Tomatoes grown on a field plot were treated with 14 C-carbendazim. After harvest, the tomatoes were processed into tomato juice and canned whole fruit. The magnitude and nature of residues in samples taken at several processing steps were determined to evaluate the effect of commercial processing on removing or eliminating the residues. The results showed that the surface residues on tomato would be removed efficiently by simple washing of tomato. A buffer solution of phosphate had the highest efficiency. Tomato juice contained lower residues than canned whole fruit

Foamed emulsion drainage: flow and trapping of drops.

Science.gov (United States)

Schneider, Maxime; Zou, Ziqiang; Langevin, Dominique; Salonen, Anniina

2017-06-07

Foamed emulsions are ubiquitous in our daily life but the ageing of such systems is still poorly understood. In this study we investigate foam drainage and measure the evolution of the gas, liquid and oil volume fractions inside the foam. We evidence three regimes of ageing. During an initial period of fast drainage, both bubbles and drops are very mobile. As the foam stabilises drainage proceeds leading to a gradual decrease of the liquid fraction and slowing down of drainage. Clusters of oil drops are less sheared, their dynamic viscosity increases and drainage slows down even further, until the drops become blocked. At this point the oil fraction starts to increase in the continuous phase. The foam ageing leads to an increase of the capillary pressure until the oil acts as an antifoaming agent and the foam collapses.

Study on the reutilization of clear fracturing flowback fluids in surfactant flooding with additives for Enhanced Oil Recovery (EOR.

Directory of Open Access Journals (Sweden)

Caili Dai

Full Text Available An investigation was conducted to study the reutilization of clear fracturing flowback fluids composed of viscoelastic surfactants (VES with additives in surfactant flooding, making the process more efficient and cost-effective. The clear fracturing flowback fluids were used as surfactant flooding system with the addition of α-olefin sulfonate (AOS for enhanced oil recovery (EOR. The interfacial activity, emulsification activity and oil recovery capability of the recycling system were studied. The interfacial tension (IFT between recycling system and oil can be reduced by 2 orders of magnitude to 10(-3 mN/m, which satisfies the basic demand of surfactant flooding. The oil can be emulsified and dispersed more easily due to the synergetic effect of VES and AOS. The oil-wet surface of quartz can be easily converted to water-wet through adsorption of surfactants (VES/AOS on the surface. Thirteen core plug flooding tests were conducted to investigate the effects of AOS concentrations, slug sizes and slug types of the recycling system on the incremental oil recovery. The investigations prove that reclaiming clear fracturing flowback fluids after fracturing operation and reuse it in surfactant flooding might have less impact on environment and be more economical.

Influence of lubricant oil residual fraction on recycled high density polyethylene properties and plastic packaging reverse logistics proposal

Directory of Open Access Journals (Sweden)

Harley Moraes Martins

2015-10-01

Full Text Available Abstract To recycle post-consumer HDPE contaminated with waste lubricating oils, companies include prior washing and drying in the process. This consumes large amounts of water and energy, generates significant effluent requiring treatment. This study assesses lubricating oil influence on HDPE properties to evaluate the feasibility of its direct mechanical recycling without washing. The current lubricating oil packaging reverse logistics in Rio de Janeiro municipality is also analyzed. HDPE bottle samples were processed with seven oil contents ranging from 1.6-29.4 (wt%. The results indicated the possibility to reprocess the polymer with oily residue not exceeding 3.2%. At higher levels, the external oil lubricating action affects the plastic matrix processing in the extruder and injection, and the recycled material has a burnt oil odor and free oil on the surface. Small residual oil amounts retain the plastic properties comparable to the washed recycled polymer and exhibited benefits associated with the oil plasticizer action. However, oil presence above 7.7% significantly changes the properties and reduces the elasticity and flexural modulus and the plastic matrix crystallinity.

Interfacial binding of cutinase rather than its catalytic activity determines the steady state interfacial tension during oil drop lipid hydrolysis.

Science.gov (United States)

Flipsen, J A; van Schaick, M A; Dijkman, R; van der Hijden, H T; Verheij, H M; Egmond, M R

1999-02-01

Hydrolysis of triglycerides by cutinase from Fusarium solani pisi causes in oil drop tensiometer experiments a decrease of the interfacial tension. A series of cutinase variants with amino acid substitutions at its molecular surface yielded different values of the steady state interfacial tension. This tension value poorly correlated with the specific activity as such nor with the total activity (defined as the specific activity multiplied by the amount of enzyme bound) of the cutinase variants. Moreover, it appeared that at activity levels above 15% of that of wild type cutinase the contribution of hydrolysis to the decrease of the tension is saturating. A clear positive correlation was found between the interfacial tension plateau value and the interfacial binding of cutinase, as determined with attenuated total reflection Fourier transformed infrared spectroscopy (ATR-FTIR). These results indicate that the interfacial steady state level is not determined by the rate of hydrolysis, but mainly by the interfacial binding of cutinase.

Instant controlled pressure drop technology and ultrasound assisted extraction for sequential extraction of essential oil and antioxidants.

Science.gov (United States)

Allaf, Tamara; Tomao, Valérie; Ruiz, Karine; Chemat, Farid

2013-01-01

The instant controlled pressure drop (DIC) technology enabled both the extraction of essential oil and the expansion of the matrix itself which improved solvent extraction. The sequential use of DIC and Ultrasound Assisted Extraction (UAE) triggered complementary actions materialized by supplementary effects. We visualized these combination impacts by comparing them to standard techniques: Hydrodistillation (HD) and Solvent Extraction (SE). First, the extraction of orange peel Essential Oils (EO) was achieved by HD during 4h and DIC process (after optimization) during 2 min; EO yields was 1.97 mg/g dry material (dm) with HD compared to 16.57 mg/g d m with DIC. Second, the solid residue was recovered to extract antioxidant compounds (naringin and hesperidin) by SE and UAE. Scanning electron microscope showed that after HD the recovered solid shriveled as opposite to DIC treatment which expanded the product structure. HPLC analyses showed that the best kinetics and yields of naringin and hesperidin extraction was when DIC and UAE are combined. Indeed, after 1h of extraction, DIC treated orange peels with UAE were 0.825 ± 1.6 × 10(-2)g/g of dry material (dm) for hesperidin and 6.45 × 10(-2) ± 2.3 × 10(-4)g/g d m for naringin compared to 0.64 ± 2.7 × 10(-2)g/g of dry material (dm) and 5.7 × 10(-2) ± 1.6 × 10(-3)g/g d m, respectively with SE. By combining DIC to UAE, it was possible to enhance kinetics and yields of antioxidant extraction. Copyright © 2012 Elsevier B.V. All rights reserved.

The effect of commercial processing procedures on {sup 14}C-carbendazim residues in soybean oil and tomato

Energy Technology Data Exchange (ETDEWEB)

Genyuan, Peng; Huaguo, Wang; Mengwen, Qi; Fujun, Wang; Changjiu, Zhou [Laboratory for the Application of Nuclear Techniques, Beijing Agricultural University, Beijing (China)

1994-06-01

Under simulated agricultural practices, soybean plants were treated with {sup 14}C-labelled carbendazim during the blooming stage. The residue in seeds was determined to be 0.067 ppm; corresponding to 0.076 ppm respectively. After subjecting the oil to degumming, alkali treatment, bleaching and deodorization, 53.7% of original radioactivity was removed. Deodorization was the most effect process, removing about 20% of the residue. The concentration of residues in the deodorized oil decreased about 30%. In soybean seed and cake, the residue was mainly present as carbendazim, the concentration of the other metabolites did not exceed 30% of the residue. Tomatoes grown on a field plot were treated with {sup 14}C-carbendazim. After harvest, the tomatoes were processed into tomato juice and canned whole fruit. The magnitude and nature of residues in samples taken at several processing steps were determined to evaluate the effect of commercial processing on removing or eliminating the residues. The results showed that the surface residues on tomato would be removed efficiently by simple washing of tomato. A buffer solution of phosphate had the highest efficiency. Tomato juice contained lower residues than canned whole fruit.

Comparative evaluation of thermal oxidative decomposition for oil-plant residues via thermogravimetric analysis: Thermal conversion characteristics, kinetics, and thermodynamics.

Science.gov (United States)

Chen, Jianbiao; Wang, Yanhong; Lang, Xuemei; Ren, Xiu'e; Fan, Shuanshi

2017-11-01

Thermal oxidative decomposition characteristics, kinetics, and thermodynamics of rape straw (RS), rapeseed meal (RM), camellia seed shell (CS), and camellia seed meal (CM) were evaluated via thermogravimetric analysis (TGA). TG-DTG-DSC curves demonstrated that the combustion of oil-plant residues proceeded in three stages, including dehydration, release and combustion of organic volatiles, and chars oxidation. As revealed by combustion characteristic parameters, the ignition, burnout, and comprehensive combustion performance of residues were quite distinct from each other, and were improved by increasing heating rate. The kinetic parameters were determined by Coats-Redfern approach. The results showed that the most possible combustion mechanisms were order reaction models. The existence of kinetic compensation effect was clearly observed. The thermodynamic parameters (ΔH, ΔG, ΔS) at peak temperatures were calculated through the activated complex theory. With the combustion proceeding, the variation trends of ΔH, ΔG, and ΔS for RS (RM) similar to those for CS (CM). Copyright © 2017 Elsevier Ltd. All rights reserved.

A PIV Study of Drop-interface Coalescence with Surfactants

Science.gov (United States)

Weheliye, Weheliye Hashi; Dong, Teng; Angeli, Panagiota

2017-11-01

In this work, the coalescence of a drop with an aqueous-organic interface was studied by Particle Image Velocimetry (PIV). The effect of surfactants on the drop surface evolution, the vorticity field and the kinetic energy distribution in the drop during coalescence were investigated. The coalescence took place in an acrylic rectangular box with 79% glycerol solution at the bottom and Exxsol D80 oil above. The glycerol solution drop was generated through a nozzle fixed at 2cm above the aqueous/oil interface and was seeded with Rhodamine particles. The whole process was captured by a high-speed camera. Different mass ratios of non-ionic surfactant Span80 to oil were studied. The increase of surfactant concentration promoted deformation of the interface before the rupture of the trapped oil film. At the early stages after film rupture, two counter-rotating vortices appeared at the bottom of the drop which then travelled to the upper part. The propagation rates, as well as the intensities of the vortices decreased at high surfactant concentrations. At early stages, the kinetic energy was mainly distributed near the bottom part of the droplet, while at later stages it was distributed near the upper part of the droplet. Programme Grant MEMPHIS, Chinese Scholarship Council (CSC).

Experimental investigation of wettability alteration on residual oil saturation using nonionic surfactants: Capillary pressure measurement

Directory of Open Access Journals (Sweden)

Masoud Amirpour

2015-12-01

Full Text Available Introducing the novel technique for enhancing oil recovery from available petroleum reservoirs is one of the important issues in future energy demands. Among of all operative factors, wettability may be the foremost parameter affecting residual oil saturation in all stage of oil recovery. Although wettability alteration is one of the methods which enhance oil recovery from the petroleum reservoir. Recently, the studies which focused on this subject were more than the past and many contributions have been made on this area. The main objective of the current study is experimentally investigation of the two nonionic surfactants effects on altering wettability of reservoir rocks. Purpose of this work is to change the wettability to preferentially the water-wet condition. Also reducing the residual oil saturation (Sor is the other purpose of this work. The wettability alteration of reservoir rock is measured by two main quantitative methods namely contact angle and the USBM methods. Results of this study showed that surfactant flooding is more effective in oil-wet rocks to change their wettability and consequently reducing Sor to a low value. Cedar (Zizyphus Spina Christi is low priced, absolutely natural, and abundantly accessible in the Middle East and Central Asia. Based on the results, this material can be used as a chemical surfactant in field for enhancing oil recovery.

"Self-Shaping" of Multicomponent Drops.

Science.gov (United States)

Cholakova, Diana; Valkova, Zhulieta; Tcholakova, Slavka; Denkov, Nikolai; Smoukov, Stoyan K

2017-06-13

In our recent study we showed that single-component emulsion drops, stabilized by proper surfactants, can spontaneously break symmetry and transform into various polygonal shapes during cooling [ Denkov Nature 2015 , 528 , 392 - 395 ]. This process involves the formation of a plastic rotator phase of self-assembled oil molecules beneath the drop surface. The plastic phase spontaneously forms a frame of plastic rods at the oil drop perimeter which supports the polygonal shapes. However, most of the common substances used in industry appear as mixtures of molecules rather than pure substances. Here we present a systematic study of the ability of multicomponent emulsion drops to deform upon cooling. The observed trends can be summarized as follows: (1) The general drop-shape evolution for multicomponent drops during cooling is the same as with single-component drops; however, some additional shapes are observed. (2) Preservation of the particle shape upon freezing is possible for alkane mixtures with chain length difference Δn ≤ 4; for greater Δn, phase separation within the droplet is observed. (3) Multicomponent particles prepared from alkanes with Δn ≤ 4 plastify upon cooling due to the formation of a bulk rotator phase within the particles. (4) If a compound, which cannot induce self-shaping when pure, is mixed with a certain amount of a compound which induces self-shaping, then drops prepared from this mixture can also self-shape upon cooling. (5) Self-emulsification phenomena are also observed for multicomponent drops. In addition to the three recently reported mechanisms of self-emulsification [ Tcholakova Nat. Commun. 2017 , ( 8 ), 15012 ], a new (fourth) mechanism is observed upon freezing for alkane mixtures with Δn > 4. It involves disintegration of the particles due to a phase separation of alkanes upon freezing.

Persistence, biodegradation and biological impact of Bunker C residues in Black Duck Cove, Nova Scotia

Energy Technology Data Exchange (ETDEWEB)

Lee, K.; Wohlgeschaffen, G. D.; Tremblay, G. H. [Dept. of Fisheries and Oceans of Canada, Inst. Maurice-Lamontagne, Mont Joli, PQ (Canada); Vandermeulen, D. C.; Mossman, K. G. [Dept. of Fisheries and Oceans of Canada, Bedford Inst. of Oceanography, Dartmouth, NS (Canada); Doe, K. G.; Jackman, P. M. [Environment Canada, Environmental Science Center, Moncton, NB (Canada); Prince, R. C.; Garrett, R. M.; Haith, C. E. [Exxon Research and Engineering Company, Annandale, NJ (United States)

1998-12-31

In 1970, approximately 2,045 cubic metres of Bunker C oil impacted on 300 km of Nova Scotia`s coastline following the grounding of the tanker `Arrow`. Only 10 per cent of the coastline was subjected to cleanup, the remainder was left to degrade naturally. Samples of sediments were collected in 1993 and 1997 in order to assess the attenuation processes on the reduction of toxicity within sediments and interstitial waters at Black Duck Cove, one of the untreated sites where residual oil was clearly evident. Detailed chemical analyses showed that the Bunker C oil at this site has undergone substantial biodegradation. Over the 20 plus years since the oil spill the toxicity of the residual oil has been significantly reduced and there is substantial evidence of habitat recovery.

Persistence, biodegradation and biological impact of Bunker C residues in Black Duck Cove, Nova Scotia

Energy Technology Data Exchange (ETDEWEB)

Lee, K.; Wohlgeschaffen, G. D.; Tremblay, G. H. [Dept. of Fisheries and Oceans of Canada, Inst. Maurice-Lamontagne, Mont Joli, PQ (Canada); Vandermeulen, D. C.; Mossman, K. G. [Dept. of Fisheries and Oceans of Canada, Bedford Inst. of Oceanography, Dartmouth, NS (Canada); Doe, K. G.; Jackman, P. M. [Environment Canada, Environmental Science Center, Moncton, NB (Canada); Prince, R. C.; Garrett, R. M.; Haith, C. E. [Exxon Research and Engineering Company, Annandale, NJ (United States)

1998-07-01

In 1970, approximately 2,045 cubic metres of Bunker C oil impacted on 300 km of Nova Scotia's coastline following the grounding of the tanker 'Arrow'. Only 10 per cent of the coastline was subjected to cleanup, the remainder was left to degrade naturally. Samples of sediments were collected in 1993 and 1997 in order to assess the attenuation processes on the reduction of toxicity within sediments and interstitial waters at Black Duck Cove, one of the untreated sites where residual oil was clearly evident. Detailed chemical analyses showed that the Bunker C oil at this site has undergone substantial biodegradation. Over the 20 plus years since the oil spill the toxicity of the residual oil has been significantly reduced and there is substantial evidence of habitat recovery.

Identification of 3-phase flow patterns of heavy oil from pressure drop and flow rate data

Energy Technology Data Exchange (ETDEWEB)

Pacheco, F.; Bannwart, A.C.; Mendes, J.R.P. [Campinas State Univ., Sao Paulo (Brazil); Serapiao, A.B.S. [Sao Paulo State Univ., Sao Paulo (Brazil)

2008-07-01

Pipe flow of oil-gas-water mixtures poses a complex thermo-fluid dynamical problem. This paper examined the relationship between phase flow rates, flow pattern identification, and pressure drop in 3-phase water-assisted heavy oil in the presence of a gaseous phase. An artificial intelligence program called a support vector machine (SVM) was used to determine relevant parameters for flow pattern classification. Data from a 3-phase flow of heavy oil with gas and water in a vertical pipe was used in the study. The data were used to train the machine, which then predicted the flow pattern of the remaining data. Tests with different parameters and training data were then performed. The study showed that the proposed SVM flow pattern identification process accurately predicted flow patterns. It was concluded that the SVM took a relatively short amount of time to train. Future research is needed to apply the tool to larger flow datasets. 5 refs., 1 tab., 2 figs.

Effect of surfactant on single drop mass transfer for extraction of aromatics from lubricating oils

Science.gov (United States)

Izza, H.; Ben Abdessalam, S.; Korichi, M.

2018-03-01

Solvent extraction is an effective method for the reduction of the content of aromatic of lubricating oil. Frequently, with phenol, furfural, the NMP (out of N-methyl pyrrolidone). The power solvent and the selectivity can be still to increase while using surfactant as additive which facilitates the separation of phase and increases the yeild in raffinat. Liquid-liquid mass transfer coefficients for single freely rising drops in the presence of surfactant in an extraction column have been investigated. The surfactant used in this study was sodium lauryl ether sulfate (SLES). The experiments were performed by bubbling a solvent as a series of individual drops from the top of the column containing furfural-SLES solution. The column used in this experiment was made from glass with 17 mm inner diameter and a capacity of 125ml. The effects of the concentration of surfactant on the overall coefficient of mass transfer was investigated.

Downdraft gasification of pellets made of wood, palm-oil residues respective bagasse: Experimental study

International Nuclear Information System (INIS)

Erlich, Catharina; Fransson, Torsten H.

2011-01-01

The downdraft gasification technology has an increased interest among researchers worldwide due to the possibility to produce mechanical and electrical power from biomass in small-scale to an affordable price. The research is generally focused on improvement of the performance and optimizing of a certain gasifier, on testing different fuels, on increasing the user-friendliness of the gasifier and on finding other uses for the product gas than in an IC-engine, for example liquid fuel production. The main objective with the gasification tests presented here is to further contribute in the field by studying the impact of the char bed properties such as char bed porosity and pressure drop on the gasification performance as well as the impact of fuel particle size and composition on the gasification process in one and the same gasifier. In addition, there is very little gasification data available in literature of 'before disregarded' fuels such as sugar cane bagasse from sugar/alcohol production and empty fruit bunch (EFB) from the palm-oil production. By pelletizing these residues, it is possible to introduce them into downdraft gasification technology which has been done in this study. The results show that one and the same reactor can be used for a variety of fuels in pellet form, but at varying air-fuel ratios, temperature levels, gas compositions and lower heating values. Gasification of wood pellets results in a richer producer gas while EFB pellets give a poorer one with higher contents of non-combustible compounds. In this gasification study, there is almost linear relation between the air-fuel ratio and the cold-gas efficiency for the studied fuels: Higher air-fuel ratios result in better efficiency. The pressure drop in the char bed is higher for more reactive fuels, which in turn is caused by low porosity char beds.

Time course of pulmonary burden in mice exposed to residual oil fly ash

OpenAIRE

Giovanna Marcella Cavalcante Carvalho; Lilian Katie Nagato; Sheila da Silva Fagundes; Flavia Brandão dos Santos; Andrea Surrage Calheiros; Olaf eMalm; Patricia Torres Bozza; Paulo Hilario Nascimento Saldiva; Debora Souza Faffe; Patricia Rieken Macedo Rocco; Walter Araujo Zin

2014-01-01

Residual oil fly ash (ROFA) is a common pollutant in areas where oil is burned. This particulate matter (PM) with a broad distribution of particle diameters can be inhaled by human beings and putatively damage their respiratory system. Although some studies deal with cultured cells, animals, and even epidemiological issues, so far a comprehensive analysis of respiratory outcomes as a function of the time elapsed after exposure to a low dose of ROFA is wanted. Thus, we aimed to investigate the...

Impact of recharge through residual oil upon sampling of underlying ground water

International Nuclear Information System (INIS)

Wise, W.R.; Chang, Chichung; Klopp, R.A.; Bedient, P.B.

1991-01-01

At an aviation gasoline spill site in Traverse City, Michigan, historical records indicate a positive correlation between significant rainfall events and increased concentrations of slightly soluble organic compounds in the monitoring wells of the site. To investigate the recharge effect on ground water quality due to infiltrating water percolating past residual oil and into the saturated zone, an in situ infiltration experiment was performed at the site. Sampling cones were set at various depths below a circular test area, 13 feet (4 meters) in diameter. Rainfall was simulated by sprinkling the test area at a rate sufficiently low to prevent runoff. The sampling cones for soil-gas and ground water quality were installed in the unsaturated and saturated zones to observed the effects of the recharge process. Infiltrated water was determined to have transported organic constituents of the residual oil, specifically benzene, toluene, ethylbenzene, and ortho-xylene (BTEX), into the ground water beneath the water table, elevating the aqueous concentrations of these constituents in the saturated zone. Soil-gas concentrations of the organic compounds in the unsaturated zone increased with depth and time after the commencement of infiltration. Reaeration of the unconfined aquifer via the infiltrated water was observed. It is concluded that water quality measurements are directly coupled to recharge events for the sandy type of aquifer with an overlying oil phase, which was studied in this work. Ground water sampling strategies and data analysis need to reflect the effect of recharge from precipitation on shallow, unconfined aquifers where an oil phase may be present

Residual biomass potential in olive tree cultivation and olive oil industry in Spain: valorization proposal in a biorefinery contex

Energy Technology Data Exchange (ETDEWEB)

Manzanares, P.; Ruiz, E.; Ballesteros, M.; Negro, M.J.; Gallego, F.J.; López-Linares, J.C.; Castro, E.

2017-07-01

Olive crop and olive oil industry generates several residues, i.e., olive tree pruning biomass (OTPB), extracted olive pomace (EOP) and olive leaves (OL) that could be used to produce high-added value products in an integrated biorefinery. OTPB is generated in the field as a result of pruning operation to remove old branches; EOP is the main residue of the pomace olive oil extracting industry after extraction with hexane of residual oil contained in olive pomace; and OL comes from the olive cleaning process carried out at olive mills, where small branches and leaves are separated by density. In this work, an analysis of the potential of OTPB, EOP and OL residues was addressed by estimating the production volumes at national level and the spatial distribution of these residues using geographic information system software. Information provided by public institutions and personal surveys to the industries was evaluated. Moreover, chemical analysis of the residues was undertaken and the results used to make a first assessment of valorization into biofuels such as bioethanol and bio based chemicals. Results show that close to 4.2 million tons/year of EOP, OL and OTPB derived from olive oil industry and olive tree cultivation in Spain could be available as a raw material for biorefineries in Spain. The analysis of the chemical characteristics indicates the relevant potential of these feedstocks for the production of bioethanol and other compounds such as phenols based on suitable processing and conversion routes, although techno-economic evaluations must be tackled to refine this approach.

Residual biomass potential in olive tree cultivation and olive oil industry in Spain: valorization proposal in a biorefinery context

Directory of Open Access Journals (Sweden)

Paloma Manzanares

2017-12-01

Full Text Available Olive crop and olive oil industry generates several residues, i.e., olive tree pruning biomass (OTPB, extracted olive pomace (EOP and olive leaves (OL that could be used to produce high-added value products in an integrated biorefinery. OTPB is generated in the field as a result of pruning operation to remove old branches; EOP is the main residue of the pomace olive oil extracting industry after extraction with hexane of residual oil contained in olive pomace; and OL comes from the olive cleaning process carried out at olive mills, where small branches and leaves are separated by density. In this work, an analysis of the potential of OTPB, EOP and OL residues was addressed by estimating the production volumes at national level and the spatial distribution of these residues using geographic information system software. Information provided by public institutions and personal surveys to the industries was evaluated. Moreover, chemical analysis of the residues was undertaken and the results used to make a first assessment of valorization into biofuels such as bioethanol and bio based chemicals. Results show that close to 4.2 million tons/year of EOP, OL and OTPB derived from olive oil industry and olive tree cultivation in Spain could be available as a raw material for biorefineries in Spain. The analysis of the chemical characteristics indicates the relevant potential of these feedstocks for the production of bioethanol and other compounds such as phenols based on suitable processing and conversion routes, although techno-economic evaluations must be tackled to refine this approach.

Determination of residual oil saturation from time-lapse pulsed neutron capture logs in a large sandstone reservoir

International Nuclear Information System (INIS)

Syed, E.V.; Salaita, G.N.; McCaffery, F.G.

1991-01-01

Cased hole logging with pulsed neutron tools finds extensive use for identifying zones of water breakthrough and monitoring oil-water contacts in oil reservoirs being depleted by waterflooding or natural water drive. Results of such surveys then find direct use for planning recompletions and water shutoff treatments. Pulsed neutron capture (PNC) logs are useful for estimating water saturation changes behind casing in the presence of a constant, high-salinity environment. PNC log surveys run at different times, i.e., in a time-lapse mode, are particularly amenable to quantitative analysis. The combined use of the original open hole and PNC time-lapse log information can then provide information on remaining or residual oil saturations in a reservoir. This paper reports analyses of historical pulsed neutron capture log data to assess residual oil saturation in naturally water-swept zones for selected wells from a large sandstone reservoir in the Middle East. Quantitative determination of oil saturations was aided by PNC log information obtained from a series of tests conducted in a new well in the same field

Extra heavy oil and refinery residues upgrading through Eni Slurry Technology : first EST commercial unit

Energy Technology Data Exchange (ETDEWEB)

Rispoli, G.; Sanfilippo, D.; Amoroso, A [Eni S.p.A., Rome (Italy)

2009-07-01

The production of heavy crude oils is projected to continue to grow in the upstream oil industry given that large reserves of unconventional extra heavy crude and bitumen exist in several geographic areas including Canada and Venezuela. As reserves of conventional crude oil continue to decline, these unconventional feedstocks are becoming an opportunity to pursue, but they require effective technologies for upgrading and meeting the growing demand for light and middle distillate fuels. This paper described the proprietary technology that offers a solution to upstream and downstream oil producers for bottom-of-the-barrel upgrading. En i Slurry Technology (EST) is constructing an industrial plant in its Sannazzaro refinery in Italy. The plant is designed to convert 23,000 BPSD of vacuum residue into high quality diesel and other valuable refinery streams such as liquefied petroleum gas, naphtha and jet fuel. EST is an H-addition process characterized by the use of a special homogeneous isothermal intrinsically safe reactor, and of a nano-dispersed non-ageing catalyst. EST converts more than 98 per cent of any type of residues to about 110 per cent volume of light products and distillates or extra heavy oils to high quality bottomless SCO. In typical performance, HDS is greater than 85 per cent, HDM greater than 99 per cent and HDCCR greater than 97 per cent. EST also achieves the target of zero fuel oil - zero coke. 12 refs., 4 tabs., 5 figs.

Determination of macro nickel, vanadium and iron in crude oil and residues by derivative spectrophotometry

International Nuclear Information System (INIS)

Liu, W.; Wang, L.; Li, X.

1992-01-01

In this paper, a new method with derivative spectrophotometry and 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol as the chromogenic reagent in buffer solution of different pH developed for determining micro amounts of nickel. Vanadium and iron in crude oil and residues is reported. Forth-, Second- and Third-, Fourth-order derivative spectrophotometry were applied to determine nickel, nickel and vanadium, nickel and iron in crude oil and residues, respectively. The derivative maximums chosen for the measurement were at 556 nm for nickel, 540 nm and 643 nm for nickel and vanadium, 524 nm and 604 nm for nickel and iron. Beer's law is valid for the range 1.0 x 10 -6 to 2.5 x 10 -5 M

From nuclear reactions to liquid-drop collisions

International Nuclear Information System (INIS)

Menchaca R, A.; Huidobro, F.; Martinez D, A.; Michaelian, K.; Perez, A.; Rodriguez, V.; Carjan, N.

1997-01-01

A review of the experimental and theoretical situation in coalescence and fragmentation studies of binary liquid-drop collisions is given, putting in perspective our own contributions, which include experiments with mercury and oil drops and the application of a nuclear reaction model, specifically modified by us for the macroscopic case. (Author)

Drop deformation and breakup in a partially filled horizontal rotating cylinder

Science.gov (United States)

White, Andrew; Pereira, Caroline; Hyacinthe, Hyaquino; Ward, Thomas

2014-11-01

Drop deformation and breakup due to shear flow has been studied extensively in Couette devices as well as in gravity-driven flows. In these cases shear is generated either by the moving wall or the drop's motion. For such flows the drop shape remains unperturbed at low capillary number (Ca), deforms at moderate Ca , and can experience breakup as Ca --> 1 and larger. Here single drops of NaOH(aq) will be placed in a horizontal cylindrical rotating tank partially filled with vegetable oil resulting in 10-2 saponification, can yield lower minimum surface tensions and faster adsorption than non-reactive surfactant systems. Oil films between the wall and drop as well as drop shape will be observed as rotation rates and NaOH(aq) concentration are varied. Results will be presented in the context of previous work on bubble and drop shapes and breakup. NSF CBET #1262718.

Ground Motion Prediction Equations Empowered by Stress Drop Measurement

Science.gov (United States)

Miyake, H.; Oth, A.

2015-12-01

Significant variation of stress drop is a crucial issue for ground motion prediction equations and probabilistic seismic hazard assessment, since only a few ground motion prediction equations take into account stress drop. In addition to average and sigma studies of stress drop and ground motion prediction equations (e.g., Cotton et al., 2013; Baltay and Hanks, 2014), we explore 1-to-1 relationship for each earthquake between stress drop and between-event residual of a ground motion prediction equation. We used the stress drop dataset of Oth (2013) for Japanese crustal earthquakes ranging 0.1 to 100 MPa and K-NET/KiK-net ground motion dataset against for several ground motion prediction equations with volcanic front treatment. Between-event residuals for ground accelerations and velocities are generally coincident with stress drop, as investigated by seismic intensity measures of Oth et al. (2015). Moreover, we found faster attenuation of ground acceleration and velocities for large stress drop events for the similar fault distance range and focal depth. It may suggest an alternative parameterization of stress drop to control attenuation distance rate for ground motion prediction equations. We also investigate 1-to-1 relationship and sigma for regional/national-scale stress drop variation and current national-scale ground motion equations.

PHYSICOCHEMICAL CHARACTERISTICS, PESTICIDE RESIDUE AND AFLATOXIN CONTAMINATION OF COLD PRESSED PUMPKIN SEED (Cucurbita pepo L. OILS FROM CENTRAL ANATOLIA REGION OF TURKEY

Directory of Open Access Journals (Sweden)

FATMA NUR ARSLAN

2017-06-01

Full Text Available In this study, physicochemical characteristics, pesticide residues and aflatoxin contaminations of cold pressed pumpkin seed (Cucurbita pepo L. oils cultivated in four different central Anatolia regions of Turkey, were investigated. Lab-scale screw press machine was used to produce cold pressed pumpkin seed oils and the oil contents were found between 42.8%−47.4% for naked seeds. The physicochemical characteristic (refractive index, viscosity, color value, triglyceride profile analysis, peroxide value, iodine value, free fatty acid, saponification number, unsaponified matter, specific extinction values at 232 and 270 nm of cold pressed oils were determined by using different analytical techniques. The results showed that there was a non-significant difference between cold pressed pumpkin seed oils from different regions, in terms of physicochemical characteristics. The contents of pesticide residue and aflatoxin B1, B2, G1 and G2 contamination were determined by using validated UHPLC-MS/MS method. The chlorpyrifos pesticide residue was detected under the limit value declared by official authorities for the quality assessment of edible oils. Aflatoxins weren’t detected in any of studied pumpkin seed oils. Therefore, in food industry the positive effect of screw-pressing application could be useful for preservation of bioactive compounds during edible oil production and also enhancing of their functional properties.

Investigation of biosurfactant-producing indigenous microorganisms that enhance residue oil recovery in an oil reservoir after polymer flooding.

Science.gov (United States)

She, Yue-Hui; Zhang, Fan; Xia, Jing-Jing; Kong, Shu-Qiong; Wang, Zheng-Liang; Shu, Fu-Chang; Hu, Ji-Ming

2011-01-01

Three biosurfactant-producing indigenous microorganisms (XDS1, XDS2, XDS3) were isolated from a petroleum reservoir in the Daqing Oilfield (China) after polymer flooding. Their metabolic, biochemical, and oil-degradation characteristics, as well as their oil displacement in the core were studied. These indigenous microorganisms were identified as short rod bacillus bacteria with white color, round shape, a protruding structure, and a rough surface. Strains have peritrichous flagella, are able to produce endospores, are sporangia, and are clearly swollen and terminal. Bacterial cultures show that the oil-spreading values of the fermentation fluid containing all three strains are more than 4.5 cm (diameter) with an approximate 25 mN/m surface tension. The hydrocarbon degradation rates of each of the three strains exceeded 50%, with the highest achieving 84%. Several oil recovery agents were produced following degradation. At the same time, the heavy components of crude oil were degraded into light components, and their flow characteristics were also improved. The surface tension and viscosity of the crude oil decreased after being treated by the three strains of microorganisms. The core-flooding tests showed that the incremental oil recoveries were 4.89-6.96%. Thus, XDS123 treatment may represent a viable method for microbial-enhanced oil recovery.

Evaluation of PAH depletion of subsurface Exxon Valdez oil residues remaining in Prince William Sound in 2007-2008 and their likely bioremediation potential

Energy Technology Data Exchange (ETDEWEB)

Atlas, R. [Louisville Univ., Louisville, KY (United States); Bragg, J.R. [Creative Petroleum Solutions LLC, Houston, TX (United States)

2009-07-01

This study examined the extent of oil weathering at the Exxon Valdez oil spill (EVOS) sites and estimated the bioremediation potential for shoreline segments by examining the depletion of total polycyclic aromatic hydrocarbons (PAHs) relative to an estimated applicability threshold of 70 per cent. The distribution of oil was examined by location and current ratios of nitrogen and non-polar oil in order to assess if biodegradation rates were nutrient-limited. The impact of sequestration on the effectiveness of bioremediation was also studied. Results of the study showed that the EVOS residues are patchy and infrequently found on sites that were heavily oiled in 1989. Only 0.4 per cent of the oil originally stranded in 1989 remained. The remaining EVOS residues are sequestered under boulder and cobble armour in areas with limited contact with flowing water. The study also showed that concentrations of nitrogen and dissolved oxygen in pore waters within strata adjacent to the sequestered oil can support biodegradation. Most remaining EVOS residues are highly weathered and biodegraded. It was concluded that nutrients added to the shorelines are unlikely to effectively contact the sequestered oil. 31 refs., 2 tabs., 14 figs.

Laboratory studies of the properties of in-situ burn residues: chemical composition of residues

International Nuclear Information System (INIS)

Trudel, B.K.; Buist, I.A.; Schatzke, D.; Aurand, D.

1996-01-01

The chemical composition of the residue from small-scale burns of thick oil slicks was studied. The objective was to describe the changes in chemical composition in oils burning on water and to determine how these changes were influenced by the condition of the burn. Small-scale test burns involved burning 40-cm diameter pools of oil on water. A range of eight oil types including seven crude oils and an automotive diesel were burned. For each oil, slicks of fresh oil of three different thicknesses were tested. Two of the oils were tested before and after weathering. Results showed that the composition of the residue differed greatly from the parent oil. Asphaltenes, high-boiling-point aromatics and resins remained concentrated in the burn residue. The burning of slicks appeared to remove most of the lower-molecular weight aromatic hydrocarbons which included the more toxic and more bioavailable components of the crude oils. 11 refs., 6 tabs

Injection of heavy fuel oil into the blast furnace

Energy Technology Data Exchange (ETDEWEB)

Paloposki, T. [Helsinki Univ. of Technology, Otaniemi (Finland); Hakala, J.; Mannila, P.; Laukkanen, J. [Oulu Univ. (Finland)

1996-12-31

This study deals with the injection and combustion of heavy fuel oil in blast furnaces. The injection of the oil was studied experimentally in a small-scale test rig. The combustion of the oil was analysed with a commercial computer program for flow and combustion simulations. Results from computer simulations show that the combustion of the oil can be improved by decreasing the size of the oil drops and by enhancing the mixing between the oil drops and the hot blast. The devolatilization rate of the oil mainly depends on the size of the oil drops. The combustion rate of the volatiles mainly depends on the effectiveness of turbulent mixing with combustion air. Methods to decrease the size of the oil drops were sought in the experimental part of the study. Experimental results show that the size of the oil drops increases with increasing mass flow rate of the oil and decreases with increasing velocity of the hot blast. Methods to improve the mixing between the oil drops and the hot blast are suggested but have not yet been experimentally tested. (author) (4 refs.)

Injection of heavy fuel oil into the blast furnace

Energy Technology Data Exchange (ETDEWEB)

Paloposki, T [Helsinki Univ. of Technology, Otaniemi (Finland); Hakala, J; Mannila, P; Laukkanen, J [Oulu Univ. (Finland)

1997-12-31

This study deals with the injection and combustion of heavy fuel oil in blast furnaces. The injection of the oil was studied experimentally in a small-scale test rig. The combustion of the oil was analysed with a commercial computer program for flow and combustion simulations. Results from computer simulations show that the combustion of the oil can be improved by decreasing the size of the oil drops and by enhancing the mixing between the oil drops and the hot blast. The devolatilization rate of the oil mainly depends on the size of the oil drops. The combustion rate of the volatiles mainly depends on the effectiveness of turbulent mixing with combustion air. Methods to decrease the size of the oil drops were sought in the experimental part of the study. Experimental results show that the size of the oil drops increases with increasing mass flow rate of the oil and decreases with increasing velocity of the hot blast. Methods to improve the mixing between the oil drops and the hot blast are suggested but have not yet been experimentally tested. (author) (4 refs.)

Chemical durability of glass and glass-ceramic materials, developed in laboratory scale, from industrial oil shale residue. Preliminary results

International Nuclear Information System (INIS)

Araujo Fonseca, M.V. de; Souza Santos, P. de

1990-01-01

Industrial developments frequently drive to the natural resources extinction. The recycling era has come out a long time ago and it has been evident that great part of industrial work's problems are related to the pollution and the raw materials extinction. These problems should be solved, with advantages, through industrial residues recycling. This study deals with glass and glass-ceramics materials obtained from oil shale (Irati Formation-Sao Mateus do Sul-Parana State) industrialization residues. The reached results show that a controled devitrification of retorted oil shale glass improves its performance related to chemical attack. The crystallinity caracterization of the oil shales glass-ceramic was made through X-ray diffraction. (author) [pt

Stability of tetrachlorvinphos residues in faba beans and soya bean oil towards different processing procedures

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Farghaly, M.

1987-01-01

Cooking of contaminated faba beans did not degrade the originally present potentially toxic residues, namely, tetrachlorvinphos and its desmethyl derivative to any appreciable extent. Processing of contaminated soya bean oil, on the other hand, led to degradation of tetrachlorvinphos and its metabolites to give mono and dimethyl phosphates. Feeding of mice with bound residues of tetrachlorvinphos in beans for 90 days led to an apparent decrease in the rate of body weight gain. (author)

Radiation protection and management of NORM residues in the oil and gas industry

International Nuclear Information System (INIS)

Haridasan, P.P.; )

2014-01-01

The radionuclides in oil and gas streams belong to the decay chains of 238 U and 232 Th originate from the reservoir rock that contains oil, gas and formation water. Formation water contains significant concentrations of isotopes of radium dissolved from the reservoir rock. The parent isotopes of uranium and thorium are not mobilized from the rock and hence the radium isotopes appear in the water co-produced with the oil and gas. When the ions of Group II elements are present in the produced water, drops in pressure and temperature can lead to precipitation of sulphate and carbonate scales on the inner walls of production tubulars, well heads, valves, pumps, separators, water treatment vessels, gas treatment and oil storage tanks. The mixed stream of oil, gas and water carries the radon gas generated in the reservoir rock and in the production stream it preferentially follows the dry export gases. Consequently the equipment from gas treatment and transport facilities may accumulate a thin film of 210 Pb in the inner surfaces of gas lines. The radionuclide concentrations in produced water, hard scale and sludge will be presented. Indication on typical quantities of wastes generated and best practices followed in the industry in managing such wastes will be outlined. Information on external gamma exposure and potential internal exposure as well as global emerging issues will be discussed

Characterization of virgin walnut oils and their residual cakes produced from different varieties.

Science.gov (United States)

Ojeda-Amador, Rosa M; Salvador, María Desamparados; Gómez-Alonso, Sergio; Fregapane, Giuseppe

2018-06-01

This study addresses the composition and properties of different walnut varieties (Chandler, Hartley and Lara), in particular their virgin oils and residual cakes obtained by screw pressing employing different cultivars. Among nuts, walnut (Juglans regia L.) exhibits interesting nutritional value, mainly due to their high content in linoleic acid, phenolic and tocopherol compounds, which show antioxidant and other healthy properties. Valuable results related to fatty acid profile and minor components were observed. Virgin walnut oil is a rich source in linoleic acid (60-62%) and γ-tocopherol (517-554 mg/kg). Moreover, walnuts show a very high content in total phenolic compounds (10,045-12,474 mg/kg; as gallic acid), which contribute to a great antioxidant activity (105-170 mmol/kg for DPPH, and 260-393 mmol/kg for ORAC), being the hydrolysable tannins (2132-4204 mg/kg) and flavanols (796-2433 mg/kg) their main phenolic groups. Aldehydes account for the highest contribution to aromatic volatiles in virgin walnut oil (about 35% of total). As expected, polar phenolic compounds concentrate in the residual cake, after the separation of the oily phase, reaching a content of up to 19,869 mg/kg, leading to potential added value and applications as source of bioactive compounds to this by-product. Copyright © 2018 Elsevier Ltd. All rights reserved.

Oil-in-water emulsions flow through constricted micro-capillarities

Energy Technology Data Exchange (ETDEWEB)

Castillo, Oswaldo Robles; Carvalho, Marcio da Silveira [Pontificia Universidade Catolica do Rio de Janeiro (PUC-Rio), RJ (Brazil). Dept. of Mechanical Engineering

2010-07-01

The effect of the oil concentration and the drop size distribution on the characteristics of the flow of an emulsion through a constricted capillary was experimentally analyzed and quantified by the ratio of the pressure drop of the continuous phase flow to the pressure drop of the emulsion flow, at the same flow rate. The results confirm that the ratio between the capillary constriction diameter and the oil drop size is one of the most important parameters for this flow. For large oil drop size emulsions, the deformation of the drop as it flows through the constriction leads to a high extra pressure drop at low capillary numbers. For small oil drop size emulsions, the extra pressure drop is a function of the viscosity ratio and the disperse phase concentration. (author)

Radiotracer studies of pesticide residues in edible oil seeds and related products

International Nuclear Information System (INIS)

1979-01-01

Ten papers were presented in which chemical pollution due to insecticides was examined in edible oil seeds and their products. They include hexachlorocyclohexane residues in groundnut; carbaryl in groundnut; maize and cotton seed products, and in lactating goats; propoxur in cocoa beans; and leptophos residues in cotton seed and its products and in lactating goats. Eight of these papers constitute separate INIS entries. Egypt, Ghana, India, Korea, Lebanon, Pakistan, the Philippines, Poland, and the Sudan participated under the coordinated research programme. The progress of the programme is reviewed, and problems and priorities for future development of the programme are identified. A number of recommendations are addressed to the Joint FAO/IAEA Secretariat

Radiotracer studies on the fate and transformation of pesticide residues in the environment and food chains. Part of a coordinated programme on isotopic-tracer-aided studies of chemical residues in cotton seed, feed, oil and related products

International Nuclear Information System (INIS)

Lee, S.R.

1980-10-01

The magnitude and fate of some pesticide chemicals in Korean foods were studied with particular reference to oil-bearing crops and related products. Application of the chemicals was made under conditions of actual agricultural practice. Analytical methodologies included nuclear activation, gas chromatographic, spectrophotometric and radiotracer techniques. Residues of benzene hexachloride, heptachlor, heptachlor epoxide, aldrin, dieldrin, endrin and DDT found in refined vegetable oil samples were below or within the tolerance limits set by international organizations and as such, these are unlikely to present any toxicological hazard to the consumer. Also, residues of the herbicides nitrogen, alachlor and butachlor applied to oil-bearing crops were not detected in the seeds. Studies on 14 C-BHC residues in rice revealed that polishing and washing play an important role in removing a considerable portion of the residue. Data on the arsenic-containing neoasozine residues suggest that the products consumed by the human (grain and oil) contained residues below the tolerance limit and are unlikely to present any toxicological hazard to the consumer. On the other hand, relatively high arsenic concentrations (2.2 mg/kg) were found in the cake (serving as animal feed) and should be carefully evaluated in the light of toxicological data

Thermogravimetric investigation of the co-combustion between the pyrolysis oil distillation residue and lignite.

Science.gov (United States)

Li, Hao; Xia, Shuqian; Ma, Peisheng

2016-10-01

Co-combustion of lignite with distillation residue derived from rice straw pyrolysis oil was investigated by non-isothermal thermogravimetric analysis (TGA). The addition of distillation residue improved the reactivity and combustion efficiency of lignite, such as increasing the weight loss rate at peak temperature and decreasing the burnout temperature and the total burnout. With increasing distillation residue content in the blended fuels, the synergistic interactions between distillation residue and lignite firstly increased and then decreased during co-combustion stage. Results of XRF, FTIR, (13)C NMR and SEM analysis indicated that chemical structure, mineral components and morphology of samples have great influence on the synergistic interactions. The combustion mechanisms and kinetic parameters were calculated by the Coats Redfern model, suggesting that the lowest apparent activation energy (120.19kJ/mol) for the blended fuels was obtained by blending 60wt.% distillation residue during main co-combustion stage. Copyright © 2016 Elsevier Ltd. All rights reserved.

Effect of washing on pesticide residues in olives.

Science.gov (United States)

Guardia-Rubio, M; Ayora-Cañada, M J; Ruiz-Medina, A

2007-03-01

The present work aims at contributing to the knowledge of the fate of 5 pesticides in olives in order to evaluate how washing may affect the presence of these residues in this fruit (and consequently in olive oil). For this purpose, olives were sprayed with commercial formulations containing the active ingredients and a series of analyses were performed for 64 d by using gas chromatography with mass spectrometric detection. Selected pesticides, ranked by their importance, were diuron, terbuthylazine, simazine, alpha-endosulfan, and beta-endosulfan. The pesticide fraction, which was not removable from olives by washing, increased with time after treatment until their degradation started at week 6. Washing performed 1 d after treatment was the most effective in reducing residues, especially for simazine. Consequently, the washing step performed in olive mills could be effective in removing those herbicide residues present in olives as a consequence of contact with contaminated soil for a short time. This happens when olives are dropped and harvested off the ground by means of brushes or suction equipment.

Characterization of oil shale, isolated kerogen, and post-pyrolysis residues using advanced 13 solid-state nuclear magnetic resonance spectroscopy

Science.gov (United States)

Cao, Xiaoyan; Birdwell, Justin E.; Chappell, Mark A.; Li, Yuan; Pignatello, Joseph J.; Mao, Jingdong

2013-01-01

Characterization of oil shale kerogen and organic residues remaining in postpyrolysis spent shale is critical to the understanding of the oil generation process and approaches to dealing with issues related to spent shale. The chemical structure of organic matter in raw oil shale and spent shale samples was examined in this study using advanced solid-state 13C nuclear magnetic resonance (NMR) spectroscopy. Oil shale was collected from Mahogany zone outcrops in the Piceance Basin. Five samples were analyzed: (1) raw oil shale, (2) isolated kerogen, (3) oil shale extracted with chloroform, (4) oil shale retorted in an open system at 500°C to mimic surface retorting, and (5) oil shale retorted in a closed system at 360°C to simulate in-situ retorting. The NMR methods applied included quantitative direct polarization with magic-angle spinning at 13 kHz, cross polarization with total sideband suppression, dipolar dephasing, CHn selection, 13C chemical shift anisotropy filtering, and 1H-13C long-range recoupled dipolar dephasing. The NMR results showed that, relative to the raw oil shale, (1) bitumen extraction and kerogen isolation by demineralization removed some oxygen-containing and alkyl moieties; (2) unpyrolyzed samples had low aromatic condensation; (3) oil shale pyrolysis removed aliphatic moieties, leaving behind residues enriched in aromatic carbon; and (4) oil shale retorted in an open system at 500°C contained larger aromatic clusters and more protonated aromatic moieties than oil shale retorted in a closed system at 360°C, which contained more total aromatic carbon with a wide range of cluster sizes.

Ultrasound-assisted single-drop microextraction for the determination of cadmium in vegetable oils using high-resolution continuum source electrothermal atomic absorption spectrometry

International Nuclear Information System (INIS)

Almeida, Jorge S.; Anunciação, Taiana A.; Brandão, Geovani C.; Dantas, Alailson F.; Lemos, Valfredo A.

2015-01-01

This work presents an ultrasound-assisted single-drop microextraction procedure for the determination of cadmium in vegetable oils using high-resolution continuum source electrothermal atomic absorption spectrometry. Some initial tests showed that the best extraction efficiency was obtained when using ultrasound instead of mechanical agitation, indicating that acoustic cavitation improved the extraction process. Nitric, hydrochloric and acetic acids were evaluated for use in the extraction process, and HNO 3 gave the best results. A two-level full-factorial design was applied to investigate the best conditions for the extraction of Cd from the oil samples. The influences of the sonication amplitude, time and temperature of the extraction were evaluated. The results of the design revealed that all of the variables had a significant effect on the experimental results. Afterward, a Box–Behnken design was applied to determine the optimum conditions for the determination of cadmium in vegetable oil samples. According to a multivariate study, the optimum conditions were as follows: sonication amplitude of 60%, extraction time of 15 min, extraction temperature of 46 °C and 0.1 mol L −1 HNO 3 as the extractor solution. Under optimized conditions, the developed method allows for the determination of Cd in oil samples with a limit of quantification of 7.0 ng kg −1 . Addition and recovery experiments were performed in vegetable oil samples to evaluate the accuracy of the method, and the recoveries obtained varied from 90% to 115%. The samples were also analyzed after the acid digestion procedure, and the paired t-test (95% confidence level) did not show significant differences from the proposed method. - Highlights: • The determination of cadmium in vegetable oils was developed using UA-SDME. • HR-CS ET-AAS was employed as a detection technique with direct drop sampling. • The procedure allowed for a reduction in the consumption of reagents and samples

Coumarins as turn on/off fluorescent probes for detection of residual acetone in cosmetics following headspace single-drop microextraction.

Science.gov (United States)

Cabaleiro, N; de la Calle, I; Bendicho, C; Lavilla, I

2014-11-01

In this work, a new method based on headspace-single drop microextraction for the determination of residual acetone in cosmetics by microfluorospectrometry is proposed. Acetone causes fluorescence changes in a 2.5 µL-ethanolic drop (40% v/v) containing 3.10(-4) mol L(-1) 7-hydroxy-4-methylcoumarin ('turn off') or 6.10(-6) mol L(-1) 7-diethylamino-4-methylcoumarin ('turn on'). Polarity and ability to form hydrogen bonds of short chain alcohols (polar protic solvents) were crucial in order to observe these changes in the presence of acetone (polar aprotic solvent). Parameters related with the HS-SDME procedure were studied, namely headspace volume, composition, volume and temperature of drop, microextraction time, stirring rate, mass and temperature of sample, as well as the effect of potential interferents (alcohols and fragrances). The high volatility of acetone allows its extraction from an untreated cosmetic sample within 3 min. A detection limit of 0.26 µg g(-1) and repeatability, expressed as relative standard deviation, around 5% were reached. Accuracy of the proposed methodology was evaluated by means of recovery studies. The method was successfully used to analyze different cosmetics. Simplicity and high sample throughput can be highlighted. Copyright © 2014 Elsevier B.V. All rights reserved.

Effects of oil drops containing Lactobacillus salivarius WB21 on periodontal health and oral microbiota producing volatile sulfur compounds.

Science.gov (United States)

Suzuki, Nao; Tanabe, Kazunari; Takeshita, Toru; Yoneda, Masahiro; Iwamoto, Tomoyuki; Oshiro, Sueko; Yamashita, Yoshihisa; Hirofuji, Takao

2012-03-01

The objective of this paper is to evaluate the effects of oil drops containing Lactobacillus salivarius WB21 on periodontal health and oral microbiota producing volatile sulfur compounds (VSCs). For this study, 42 subjects were randomly assigned to receive oil samples containing L. salivarius WB21 or a placebo for two weeks. Oral assessment and saliva collection were performed on days 1 and 15. Bacterial analysis was performed using the real-time polymerase chain reaction and terminal restriction fragment length polymorphism (T-RFLP). In both the experimental and placebo groups, the average probing depth, number of periodontal pockets, and the percentage of bleeding on probing (BOP) decreased while stimulated salivary flow increased on day 15. BOP was reduced in the experimental group compared with the placebo group (P = 0.010). In the experimental group, total bacterial numbers decreased, and the number of L. salivarius increased. The number of Prevotella intermedia, which is correlated with hydrogen sulfide concentration in mouth air, increased in the placebo group and did not change in the experimental group. T-RFLP analysis found that the peak area proportions representing Porphyromonas gingivalis, P. intermedia, Tannerella forsythensis, and Fusobacterium nucleatum decreased in the experimental group, although there was no significant change in the bacterial composition. Thus we observed oil drops containing L. salivarius WB21 improved BOP and inhibited the reproduction of total and VSC-producing periodontopathic bacteria compared with the placebo group, but also showed the limit of its efficacy in controlling VSCs producing and periodontal pathogens.

Pro biotic as Alternative to Antibiotic for Broiler Chicken fed Food Industrial Residual Oil

International Nuclear Information System (INIS)

EL-Faramawy, A.A.; El-Maghraby, A.F.; El-Danasoury, M.M.; Hussien, H.A.; Hegazy, E.S.

2016-01-01

This study aimed to evaluate the effect of pro biotic (some lactic acid bacteria) with different levels of food industrial residual oil in broiler commercial diets on growth performance, meat yield, internal organs, economical efficiency and performance index. One hundred and eighty one day old Cobb chicks (45 ± 0.4 g) were equally and randomly divided into 6 groups namely; the antibiotic with fresh oil (FO), the antibiotic with mixed oil (MO) [FO+RO ( 1:1 w/w)], the antibiotic with food industrial residual oil (RO), the pro biotic with FO, the pro biotic with MO and the pro biotic with RO. Virginiamycin, Phibro, USA (15 ppm), was the antibiotic, while a mixture of lactic acid bacteria is chosen as pro biotic. Both were added to the water. During the experiment which lasted for 42 days, the body weight, the feed intake and the mortality rate were recorded at 2, 4 and 6 weeks of age then the body weight gain, feed conversion ratio, economical efficiency and performance index were calculated. The results revealed that the average body weight, body weight gain and feed consumption significantly (P 0.05) while liver increased significantly (P<0.05) in pro biotic FO and gizzard in all pro biotic group and antibiotic MO. The highest performance index was observed in groups of birds treated with pro biotic with MO followed by birds treated with pro biotic FO without significant difference. It could be concluded that supplementation of pro biotic in broiler diet containing different levels of RO was economically more beneficial than antibiotic

Comparison of crude oil interfacial behavior

Energy Technology Data Exchange (ETDEWEB)

Beetge, J.H.; Panchev, N. [Champion Technologies Inc., Fresno, TX (United States)

2008-07-01

The bulk properties of crude oil are used to predict its behaviour with regards to treatment, transport and processing. Surface active components, such as asphaltenes, are often used to study or explain critical interfacial behaviour of crude oil. This study investigated the differences and similarities in the interfacial behaviour of the collective surface active component in various crude oils from different sources. The properties of interfaces between crude oil and water were compared using a Teclis drop shape tensiometer. A portion of a crude oil sample was diluted in toluene and contacted with water in a rising drop configuration. Dynamic surface tension and interfacial rheology was examined as a function of time from the early stages of interface formation. Sinusoidal oscillation of the drop volume allowed for the evaluation of visco-elastic behaviour of the crude oil/water interface as it developed with time. The Gibbs elastic modulus, as well as its elastic and viscose components were calculated from the drop shape. The interfacial behaviour was expressed in terms of concentration, oscillation frequency and interface age. It was concluded that knowledge of crude oil interfacial character could be of value in the treatment, transport and processing of crude oils because the its behaviour may play a significant role in crude oil production and processing.

Characterization of oil-palm trunk residue degradation enzymes derived from the isolated fungus, Penicillium rolfsii c3-2(1) IBRL.

Science.gov (United States)

Lee, Kok Chang; Arai, Takamitsu; Ibrahim, Darah; Deng, Lan; Murata, Yoshinori; Mori, Yutaka; Kosugi, Akihiko

2016-01-01

This study characterizes crude enzymes derived from Penicillium rolfsii c3-2(1) IBRL, a mesophilic fungus isolated from the local soil of Malaysia. Prior to enzyme activity evaluation, P. rolfsii c3-2(1) IBRL was inoculated into a broth medium containing oil-palm trunk residues for the preparation of crude enzymes. Oil-palm trunk residues were optimally hydrolysed at pH5.0 and 50°C. P. rolfsii c3-2(1) IBRL-derived crude enzymes displayed higher thermal stability compared with the commercial enzymes, Celluclast 1.5 L and Acellerase 1500. Moreover, the hydrolysing activities of the P. rolfsii c3-2(1) IBRL-derived crude enzymes (xylan, arabinan, and laminarin) were superior compared to that of Celluclast 1.5 L and Acellerase 1500, and exhibit 2- to 3-fold and 3- to 4-fold higher oil-palm trunk residues-hydrolysing specific activity, respectively. This higher hydrolysis efficiency may be attributed to the weak 'lignin-binding' ability of the P. rolfsii c3-2(1) IBRL-derived enzymes compared to the commercial enzymes.

Vortex-Induced Vapor Explosion during Drop Impact on a Superheated Pool

KAUST Repository

Alchalabi, M.A.

2017-04-18

Ultra high-speed imaging is used to investigate the vapor explosion when a drop impacts onto a high-temperature pool. The two liquids are immiscible, a low boiling-temperature perfluorohexane drop, at room temperature, which impacts a high boiling-temperature soybean-oil pool, which is heated well above the boiling temperature of the drop. We observe different regimes: weak and strong nucleate boiling, film boiling or Leidenfrost regime and entrainment followed by vapor explosion. The vapor explosions were seen to depend on the formation of a rotational flow at the edge of the impact crater, near the pool surface, which resembles a vortex ring. This rotational motion entrains a thin sheet of the drop liquid, to become surrounded by the oil. In that region, the vapor explosion starts at a point after which it propagates azimuthally along the entire periphery at high speed.

Vortex-Induced Vapor Explosion during Drop Impact on a Superheated Pool

KAUST Repository

Alchalabi, M.A.; Kouraytem, Nadia; Li, Erqiang; Thoroddsen, Sigurdur T

2017-01-01

Ultra high-speed imaging is used to investigate the vapor explosion when a drop impacts onto a high-temperature pool. The two liquids are immiscible, a low boiling-temperature perfluorohexane drop, at room temperature, which impacts a high boiling-temperature soybean-oil pool, which is heated well above the boiling temperature of the drop. We observe different regimes: weak and strong nucleate boiling, film boiling or Leidenfrost regime and entrainment followed by vapor explosion. The vapor explosions were seen to depend on the formation of a rotational flow at the edge of the impact crater, near the pool surface, which resembles a vortex ring. This rotational motion entrains a thin sheet of the drop liquid, to become surrounded by the oil. In that region, the vapor explosion starts at a point after which it propagates azimuthally along the entire periphery at high speed.

Polymer Surface Textured with Nanowire Bundles to Repel High-Speed Water Drops.

Science.gov (United States)

Li, Y P; Li, X Y; Zhu, X P; Lei, M K; Lakhtakia, A

2018-05-11

Water drops impacting windshields of high-speed trains and aircraft as well as blades in steam turbine power generators obliquely and at high speeds are difficult to repel. Impacting drops penetrate the void regions of nanotextured and microtextured superhydrophobic coatings, with this pinning resulting in the loss of drop mobility. In order to repel high-speed water drops, we nanotextured polymer surfaces with nanowire bundles separated from their neighbors by microscale void regions, with the nanowires in a bundle separated from their neighbors by nanoscale void regions. Water drops with speeds below a critical speed rebound completely. Water drops with speeds exceeding a critical speed rebound partially, but residual droplets that begin to be pinned undergo a spontaneous dewetting process and slide off. The natural oscillations of residual droplets drive this dewetting process in the interbundle void regions, resulting in a transition from the sticky Wenzel state to the slippery Cassie state without external stimuli.

Dropped Ceiling

OpenAIRE

Tabet, Rayyane

2012-01-01

On December 2nd 1950 the first drop of Saudi oil arrived to Lebanon via the newly constructed Trans-Arabian Pipeline, the world's longest pipeline and the largest American private investment in a foreign land. The 30inch wide structure which spanned 1213 kilometers passing through Saudi Arabia, Jordan, and Syria to end in Lebanon had required 3 years of planning and surveying, 2 years of installation, the fabrication of 256,000 tons of steel tubes, the employment of 30,000 workers, the ratifi...

Feasibility study on energy saving and environmental improvement via utilization of residual oil at Petron Bataan Refinery

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A feasibility study has been performed on reduction of global warming gas emission at Bataan Refinery of Petron Company in the Republic of the Philippines by utilizing residual oil in the refinery at high efficiency. In the project, installation will be implemented on thermal power generation equipment using a low-speed diesel engine that uses residual oil as fuel, and a waste heat recovered steam generation system having NOx removing equipment at Bataan Revinary of Petron Company, in addition to the existing boiler-turbine power generation system. As a result of the discussions, the annual energy saving effect in 8 years after the installation will correspond to crude oil of 50,409 tons, and in 20 years cumulatively, it will correspond to 1,017,224 tons. The annual reduction of the global warming gas emission in 8 years after the installation will be 131,698 t-CO2, or 2,657,599 t-CO2 for 20 years cumulatively. The total investment amount for these facilities is about 4.1 billion yen, whereas the investment and energy saving effects were 10.7 tons of crude oil equivalent/year-one million yen. In addition, the investment and global warming gas emission reducing effects were 28.1 t-CO2/year-one million yen. (NEDO)

Influence of instantaneous controlled pressure drop extraction conditions on composition and oil yield from Maritime Pine (Pinus Pinaster)

OpenAIRE

Rezzoug , Sid-Ahmed; Janocka , Ingrid

2007-01-01

International audience; Experiments to extract the essential oil from maritime pine (pinus pinaster) were carried out using the instantaneous controlled pressure drop process: "Détente Instantanée Contrôlée" (D.I.C). This process involves subjecting the maritime pine needles for a short period of time to a steam pressure varying from 2 to 5 bar (120 to 150 °C) during a fixed processing time, followed by an instantaneous decompression towards a vacuum (about 50 mbar). In this contribution, we ...

Ultrasound-assisted single-drop microextraction for the determination of cadmium in vegetable oils using high-resolution continuum source electrothermal atomic absorption spectrometry

Energy Technology Data Exchange (ETDEWEB)

Almeida, Jorge S.; Anunciação, Taiana A. [Departamento de Química Analítica, Instituto de Química, Universidade Federal da Bahia, Campus Universitário de Ondina, Salvador, Bahia 40170-280 (Brazil); Brandão, Geovani C. [Departamento de Química Analítica, Instituto de Química, Universidade Federal da Bahia, Campus Universitário de Ondina, Salvador, Bahia 40170-280 (Brazil); INCT de Energia e Ambiente, Instituto de Química, Universidade Federal da Bahia, Campus Universitário de Ondina, Salvador, Bahia 40170-280 (Brazil); Dantas, Alailson F. [Departamento de Química Analítica, Instituto de Química, Universidade Federal da Bahia, Campus Universitário de Ondina, Salvador, Bahia 40170-280 (Brazil); Lemos, Valfredo A. [Laboratório de Química Analítica (LQA), Universidade Estadual do Sudoeste da Bahia, Campus de Jequié, Jequié, Bahia 45506-191 (Brazil); and others

2015-05-01

This work presents an ultrasound-assisted single-drop microextraction procedure for the determination of cadmium in vegetable oils using high-resolution continuum source electrothermal atomic absorption spectrometry. Some initial tests showed that the best extraction efficiency was obtained when using ultrasound instead of mechanical agitation, indicating that acoustic cavitation improved the extraction process. Nitric, hydrochloric and acetic acids were evaluated for use in the extraction process, and HNO{sub 3} gave the best results. A two-level full-factorial design was applied to investigate the best conditions for the extraction of Cd from the oil samples. The influences of the sonication amplitude, time and temperature of the extraction were evaluated. The results of the design revealed that all of the variables had a significant effect on the experimental results. Afterward, a Box–Behnken design was applied to determine the optimum conditions for the determination of cadmium in vegetable oil samples. According to a multivariate study, the optimum conditions were as follows: sonication amplitude of 60%, extraction time of 15 min, extraction temperature of 46 °C and 0.1 mol L{sup −1} HNO{sub 3} as the extractor solution. Under optimized conditions, the developed method allows for the determination of Cd in oil samples with a limit of quantification of 7.0 ng kg{sup −1}. Addition and recovery experiments were performed in vegetable oil samples to evaluate the accuracy of the method, and the recoveries obtained varied from 90% to 115%. The samples were also analyzed after the acid digestion procedure, and the paired t-test (95% confidence level) did not show significant differences from the proposed method. - Highlights: • The determination of cadmium in vegetable oils was developed using UA-SDME. • HR-CS ET-AAS was employed as a detection technique with direct drop sampling. • The procedure allowed for a reduction in the consumption of reagents and

Biodegradation of marine oil spill residues using aboriginal bacterial consortium based on Penglai 19-3 oil spill accident, China.

Science.gov (United States)

Wang, Chuanyuan; Liu, Xing; Guo, Jie; Lv, Yingchun; Li, Yuanwei

2018-09-15

Bioremediation, mainly by indigenous bacteria, has been regarded as an effective way to deal with the petroleum pollution after an oil spill accident. The biodegradation of crude oil by microorganisms co-incubated from sediments collected from the Penglai 19-3 oil platform, Bohai Sea, China, was examined. The relative susceptibility of the isomers of alkylnaphthalenes, alkylphenanthrenes and alkyldibenzothiophene to biodegradation was also discussed. The results showed that the relative degradation values of total petroleum hydrocarbon (TPH) are 43.56% and 51.29% for sediments with untreated microcosms (S-BR1) and surfactant-treated microcosms (S-BR2), respectively. TPH biodegradation results showed an obvious decrease in saturates (biodegradation rate: 67.85-77.29%) and a slight decrease in aromatics (biodegradation rate: 47.13-57.21%), while no significant difference of resins and asphaltenes was detected. The biodegradation efficiency of alkylnaphthalenes, alkylphenanthrenes and alkyldibenzothiophene for S-BR1 and S-BR2 samples reaches 1.28-84.43% and 42.56-86.67%, respectively. The efficiency of crude oil degradation in sediment with surfactant-treated microcosms cultures added Tween 20, was higher than that in sediment with untreated microcosms. The biodegradation and selective depletion is not only controlled by thermodynamics but also related to the stereochemical structure of individual isomer compounds. Information on the biodegradation of oil spill residues by the bacterial community revealed in this study will be useful in developing strategies for bioremediation of crude oil dispersed in the marine ecosystem. Copyright © 2018 Elsevier Inc. All rights reserved.

Carbaryl residues in maize and processed products

International Nuclear Information System (INIS)

Qureshi, M.J.; Sattar, A. Jr.; Naqvi, M.H.

1981-01-01

Carbaryl residues in two local maize varieties were determined using a colorimetric method. No significant differences were observed for residues of the two varieties which ranged between 12.0 to 13.75 mg/kg in the crude oil, and averaged 1.04 and 0.67 mg/kg in the flour and cake respectively. In whole maize plants, carbaryl residues declined to approximately 2 mg/kg 35 days after treatment. Cooking in aqueous, oil or aqueous-oil media led to 63-83% loss of carbaryl residues, after 30 minutes. (author)

Characterization of enzymatically extracted sunflower seed oil as well as the protein residues

Directory of Open Access Journals (Sweden)

Sitohy, M. Z.

1993-12-01

Full Text Available Sunflower seed oil was enzymatically extracted with six different enzymes: cellulase, hemicellulase, animal proteinase, acid proteinase, pectinase and pectinex under the following conditions: substrate concentration in phosphate buffer (0.5M, pH 5 30%, enzyme concentration 2% (E/S, temperature 50°C and time 3 hours. The obtained oils were analyzed for physicochemical properties and fatty acid profiles. The protein residues were analyzed for amino acid compositions. The results showed that the enzymatic extraction with cellulase or hemicellulase could maintain good oil quality of the extracted oils as their levels of linoleic and oleic acids recorded similar values to those of the control oil extracted with organic solvents. Also the level of iodine value was in the same level of control. On the other hand, the use of proteases in the enzymatic extraction of sunflower seed oil caused some reductions in the levels of the unsaturated fatty acids as well as the iodine value. The pectinases showed a similar trend to that of the proteinase with the least recovery of linoleic acid among the different oils under study. Similarly, the use of cellulases did not change the amino acid composition of the protein residue as compared to the control, in the contrary to the extraction with the proteinases which caused reduction of some amino acids from the protein residues especially lysine, leucine, iso-leucine, alanine, arginine and aspartic. In that respect the use of pectinases behaved similar to cellulases.

Aceite de semilla de girasol fue extraído enzimáticamente con seis enzimas diferentes: celulasa, hemicelulasa, proteinasa animal, proteinase acida, pectinasa y pectinex bajo las condiciones siguientes: concentración de sustrato en tampón fosfato (0,5M, pH 5 30%, concentración enzimática 2% (E/S, temperatura 50°C y tiempo 3 horas. Los aceites obtenidos fueron analizados por sus propiedades fisicoquímicas y perfiles de ácidos grasos

Computed Tomographic-Guided Radiofrequency Ablation of Recurrent or Residual Hepatocellular Carcinomas around Retained Iodized Oil after Transarterial Chemoembolization

Energy Technology Data Exchange (ETDEWEB)

Koh, Young Hwan [Center for Liver Cancer, National Cancer Center, Goyang 410-769 (Korea, Republic of); Department of Radiology, Research Institute and Hospital, National Cancer Center, Goyang 410-769 (Korea, Republic of); Choi, Joon-Il [Center for Liver Cancer, National Cancer Center, Goyang 410-769 (Korea, Republic of); Department of Radiology, Research Institute and Hospital, National Cancer Center, Goyang 410-769 (Korea, Republic of); Department of Radiology, Seoul St. Mary' s Hospital, College of Medicine, The Catholic University of Korea, Seoul 137-701 (Korea, Republic of); Kim, Hyun Beom [Center for Liver Cancer, National Cancer Center, Goyang 410-769 (Korea, Republic of); Department of Radiology, Research Institute and Hospital, National Cancer Center, Goyang 410-769 (Korea, Republic of); Kim, Min Ju [Department of Radiology, Research Institute and Hospital, National Cancer Center, Goyang 410-769 (Korea, Republic of)

2013-07-01

To assess the clinical efficacy, safety, and risk factors influencing local tumor progression, following CT-guided radiofrequency ablation (RFA) of recurrent or residual hepatocellular carcinoma (HCC), around iodized oil retention. Sixty-four patients (M : F = 51 : 13, 65.0 ± 8.2 years old) with recurrent or residual HCC (75 index tumors, size = 14.0 ± 4.6 mm) had been treated by CT-guided RFA, using retained iodized oil as markers for targeting. The technical success, technique effectiveness rate and complications of RFA were then assessed. On pre-ablative and immediate follow-up CT after RFA, we evaluated the size of enhancing index tumors and iodized oil retention, presence of abutting vessels, completeness of ablation of iodized oil retention, and the presence of ablative margins greater than 5 mm. Also, the time interval between transarterial chemoembolization and RFA was assessed. The cumulative local tumor progression rate was calculated using the Kaplan-Meier method, and the Cox proportional hazards model was adopted, to clarify the independent factors affecting local tumor progression. The technical success and technique effectiveness rate was 100% and 98.7%, respectively. Major complications were observed in 5.6%. The cumulative rates of local tumor progression at 1 and 2 years were 17.5% and 37.5%, respectively. In multivariate analyses, partial ablation of the targeted iodized oil retention was the sole independent predictor of a higher local tumor progression rate. CT-guided RFA of HCC around iodized oil retention was effective and safe. Local tumor progression can be minimized by complete ablation of not only index tumors, but targeted iodized oil deposits as well.

STUDY OF ASPHALT BINDER OIL RESIDUE AND MUNICIPAL SOLID WASTE ASH TO BE USED IN LOW TRAFFIC PAVEMENTS

Directory of Open Access Journals (Sweden)

Michéle Dal Toé Casagrande

2014-12-01

Full Text Available The great generation of urban solid has been a concern in several countries. This work presents a study with two materials: the asphalt binder oil residue accumulated in the bottom of asphalt tanks and the municipal solid waste ash, to be used, respectively, as a substitute of conventional binder in asphalt mixtures and for soil stabilization in pavements base layers. Were evaluated properties as the mechanical behavior of the mixtures through experimental tests. The results show the potential of incorporating these residues for low traffic roads, allowing the construction of low cost roads and an environmental use of the residue.

Wetting and evaporation of binary mixture drops.

Science.gov (United States)

Sefiane, Khellil; David, Samuel; Shanahan, Martin E R

2008-09-11

Experimental results on the wetting behavior of water, methanol, and binary mixture sessile drops on a smooth, polymer-coated substrate are reported. The wetting behavior of evaporating water/methanol drops was also studied in a water-saturated environment. Drop parameters (contact angle, shape, and volume) were monitored in time. The effects of the initial relative concentrations on subsequent evaporation and wetting dynamics were investigated. Physical mechanisms responsible for the various types of wetting behavior during different stages are proposed and discussed. Competition between evaporation and hydrodynamic flow are evoked. Using an environment saturated with water vapor allowed further exploration of the controlling mechanisms and underlying processes. Wetting stages attributed to differential evaporation of methanol were identified. Methanol, the more volatile component, evaporates predominantly in the initial stage. The data, however, suggest that a small proportion of methanol remained in the drop after the first stage of evaporation. This residual methanol within the drop seems to influence subsequent wetting behavior strongly.

Characterization of interfacial waves and pressure drop in horizontal oil-water core-annular flows

Science.gov (United States)

Tripathi, Sumit; Tabor, Rico F.; Singh, Ramesh; Bhattacharya, Amitabh

2017-08-01

We study the transportation of highly viscous furnace-oil in a horizontal pipe as core-annular flow (CAF) using experiments. Pressure drop and high-speed images of the fully developed CAF are recorded for a wide range of flow rate combinations. The height profiles (with respect to the centerline of the pipe) of the upper and lower interfaces of the core are obtained using a high-speed camera and image analysis. Time series of the interface height are used to calculate the average holdup of the oil phase, speed of the interface, and the power spectra of the interface profile. We find that the ratio of the effective velocity of the annular fluid to the core velocity, α , shows a large scatter. Using the average value of this ratio (α =0.74 ) yields a good estimate of the measured holdup for the whole range of flow rate ratios, mainly due to the low sensitivity of the holdup ratio to the velocity ratio. Dimensional analysis implies that, if the thickness of the annular fluid is much smaller than the pipe radius, then, for the given range of parameters in our experiments, the non-dimensional interface shape, as well as the non-dimensional wall shear stress, can depend only on the shear Reynolds number and the velocity ratio. Our experimental data show that, for both lower and upper interfaces, the normalized power spectrum of the interface height has a strong dependence on the shear Reynolds number. Specifically, for low shear Reynolds numbers, interfacial modes with large wavelengths dominate, while, for large shear Reynolds numbers, interfacial modes with small wavelengths dominate. Normalized variance of the interface height is higher at lower shear Reynolds numbers and tends to a constant with increasing shear Reynolds number. Surprisingly, our experimental data also show that the effective wall shear stress is, to a large extent, proportional to the square of the core velocity. Using the implied scalings for the holdup ratio and wall shear stress, we can derive

Soviets may halt production drop with outside funds, technologies

International Nuclear Information System (INIS)

Riva, J.P. Jr.

1991-01-01

In a long history of Soviet oil production, a normal development progression has occurred in which several prolific oil provinces have been discovered in sequence, become dominant producers, and then declined. The present drop in Soviet oil output is partly the result of the natural decline of many of its large older fields, but also it is due to reduced capital investments in the domestic oil industry and to the reliance on outdated and inefficient exploration and development technology. This paper reports that financial and technical problems can be remedied by joint ventures with foreign oil companies. Despite these limitations, the Soviet Union has led the world in oil production ever since 1974, often by a considerable margin

Combustion of drops of Mexican fuel oils with high asphaltenes content; Combustion de gotas de combustoleos mexicanos con alto contenido de asfaltenos

Energy Technology Data Exchange (ETDEWEB)

Garcia Rodriguez, Jose Francisco [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1998-09-01

In this work the combustion of fuel drops with a content of 18% of asphaltenes has been studied . The results obtained for this fuel were compared with the ones obtained for another with a content of 12% asphaltenes. The drops were suspended in a platinum filament and burned in an spherical radiant furnace. The drop size varied between 600 and 800 microns. The fuel drops with 12% asphaltenes showed shorter combustion times, a smaller diameter increment of the smaller diameter during the combustion stages and also a shorter burning time of the carbonaceous residue than the fuel drops with a content of 18% asphaltenes. [Espanol] En el presente trabajo se ha estudiado la combustion de gotas de combustible con 18% de contenido de asfaltenos. Los resultados obtenidos para este combustible se compararon con los obtenidos para otro con 12% de contenido de asfaltenos. Las gotas fueron suspendidas en un filamento de platino y quemadas en un horno radiante esferico. El tamano de las gotas vario entre 600 y 800 micras. Las gotas de combustible con 12% de asfaltenos mostraron tiempos de combustion mas cortos, un incremento del diametro menor durante las etapas de combustion y un tiempo de quemado del residuo carbonoso tambien mas corto que las gotas del combustible con 18% de contenido de asfaltenos.

Biodiesel Production from Residual Palm Oil Contained in Spent Bleaching Earth by In Situ Trans-Esterification

Directory of Open Access Journals (Sweden)

A S Fahmil QRM

2014-06-01

Full Text Available Spent Bleaching Earth (SBE is an industrial solid waste of vegetable oil industry that has a high residual oil to be potentialy converted to biodiesel. This study aims at developing a biodiesel production process technology by utilizing residual palm oil contained in SBE and to test the use of hexane in the trans-esterification process. Optimization process was done by using the Response Surface Method (RSM. The variables studied included catalyst concentration and reaction time. On the other hand, the deoiled SBE resulted from biodiesel production was tested as an adsorbent on biodiesel purification after being reactivated. The method used in the biodiesel production included an in situ acid catalysed esterification followed by in situ base catalysed trans-esterification. The results of RSM showed that the optimum process was obtained at NaOH concentration of 1.8% and reaction time of 104.73 minutes, with a predicted response rate of 97.18% and 95.63% for validation results. The use of hexane could also increase the yield of biodiesel which was obtained on the ratio of hexane to methanol of 0.4:1 (volume of hexane: volume of methanol. On the other hand, the reactivated bleaching earth was effective as an adsorbent in biodiesel production, which was still conform with the Indonesian National Standard.

Assessment of oil pollution as consequence of the oil leaks from seabed pipeline in the Bohai Sea

International Nuclear Information System (INIS)

Wang, J.; Li, X.; Goncharov, V.K.; Klementieva, N.Y.

2005-01-01

Although oil leaks from pipelines are less dangerous than a blowout of oil as a result of a pipeline break, the presence of oil in the ocean can have a devastating affect on the marine environment, particularly as oil leaks are difficult to detect and can occur over long periods of time. This paper discussed oil pollution in the Bohai Sea. Most of the crude oil in the Bohai oil fields is heavy and contains both paraffin and sand, both of which contribute to greater incidences of cracks and corrosion wormholes in pipes. The Main Points of Model for Assessment of Environmental Consequence of the Oil Leaks from Marine Pipeline (MAECOLMP) is based on the assumption that oil leaks from wormholes on seabed pipelines generate separate oil drops which float up to create a plume in the water. After their emergence on the sea surface, an oil slick forms, which has the shape of a serpentine strip extending along the surface in the direction of the current. The main parameters that define environmental oil pollution are: the dimensions of oil drops in the water; the dimension of the oil slick on the sea surface; and the carryover of crude oil on the coastline. According to the model, the assessment of environmental effects of the oil leaks from the sea bed consist of the following stages: selection of the probable position of wormholes in the pipeline and their size; calculation of the rate of the oil leak from the wormhole for selected sizes and positions; estimation of probable average sizes of oil drops for the selected diameter of wormhole; calculation of boundaries of the plume; calculation of the width and extension of the oil slicks for each selected position of the wormhole; and estimation of the volume of crude oil that can be carried over to the coastline in each case and detection of the most dangerous accident variant. This model permits the use of the Lagrangian description in order to take into account the difference in the velocities of emerging oil drops. It

From nuclei to liquid drops

Energy Technology Data Exchange (ETDEWEB)

Menchaca-Rocha, A.; Huidobro, F.; Michaelian, K.; Perez, A.; Rodriguez, V. [Universidad Nacional Autonoma de Mexico, Mexico City (Mexico). Inst. de Fisica; Carjan, N. [Bordeaux-1 Univ., 33 - Gradignan (France). Centre d`Etudes Nucleaires

1995-12-31

Collisions of symmetric mercury-drop pairs have been studied experimentally as a function of impact parameter, in a relative-velocity range going from a coalescence-dominated region to interactions yielding several residues. The experiments are compared with predictions of a dynamical model used in nuclear physics. The time evolution of the shapes is well reproduced by the simulation. (authors). 8 refs., 3 figs.

Carbaryl residues in cottonseed products in the Philippines

International Nuclear Information System (INIS)

Pablo, F.E.

1981-01-01

Residues of carbaryl in cottonseed products were determined by spectrophotometry. Carbaryl residues in oil and cake were 0.83 and 0.04 mg/kg respectively. Parallel experiments with 14 C-carbaryl gave comparable results. 14 C-carbaryl residues in oil and cake were 0.42 and 0.15 mg/kg respectively. (author)

Self-wrapping of an ouzo drop induced by evaporation on a superamphiphobic surface

NARCIS (Netherlands)

Tan, H.; Diddens, C.; Versluis, M.; Butt, H.J.; Lohse, D.; Zhang, X.

2017-01-01

Evaporation of multi-component drops is crucial to various technologies and has numerous potential applications because of its ubiquity in nature. Superamphiphobic surfaces, which are both superhydrophobic and superoleophobic, can give a low wettability not only for water drops but also for oil

Could residual oil from the Exxon Valdez spill create a long-term population "sink" for sea otters in Alaska?

Science.gov (United States)

Monson, Daniel H.; Doak, Daniel F.; Ballachey, Brenda E.; Bodkin, James L.

2011-01-01

Over 20 years ago, the Exxon Valdez oil tanker spilled 42 million L of crude oil into the waters of Prince William Sound, Alaska, USA. At the time of the spill, the sea otter (Enhydra lutris) population inhabiting the spill area suffered substantial acute injuries and loss. Subsequent research has resulted in one of the best-studied species responses to an oil spill in history. However, the question remains: Is the spill still influencing the Prince William Sound sea otter population? Here we fit time-varying population models to data for the sea otter population of western Prince William Sound to quantify the duration and extent of mortality effects from the spill. We hypothesize that the patchy nature of residual oil left in the environment has created a source-sink population dynamic. We fit models using the age distributions of both living and dying animals and estimates of sea otter population size to predict the number of sea otters in the hypothesized sink population and the number lost to this sink due to chronic exposure to residual oil. Our results suggest that the sink population has remained at just over 900 individuals (95% CI: 606-960) between 1990 and 2009, during which time prime-age survival remained 2-6% below pre-spill levels. This reduced survival led to chronic losses of ???900 animals over the past two decades, which is similar in magnitude to the number of sea otter deaths documented in western Prince William Sound during the acute phase of the spill. However, the unaffected source population appears to be counterbalancing these losses, with the model indicating that the sea otter population increased from ???2150 individuals in 1990 to nearly 3000 in 2009. The most optimistic interpretation of our results suggests that mortality effects dissipated between 2005 and 2007. Our results suggest that residual oil can affect wildlife populations on time scales much longer than previously believed and that cumulative chronic effects can be as

Surfactant-Enhanced Benard Convection on an Evaporating Drop

Science.gov (United States)

Nguyen, Van X.; Stebe, Kathleen J.

2001-11-01

Surfactant effects on an evaporating drop are studied experimentally. Using a fluorescent probe, the distribution and surface phase of the surfactant is directly imaged throughout the evaporation process. From these experiments, we identify conditions in which surfactants promote surface tension-driven Benard instabilities in aqueous systems. The drops under study contain finely divided particles, which act as tracers in the flow, and form well-defined patterns after the drop evaporates. Two flow fields have been reported in this system. The first occurs because the contact line becomes pinned by solid particles at the contact line region. In order for the contact line to remain fixed, an outward flow toward the ring results, driving further accumulation at the contact ring. A ‘coffee ring’ of particles is left as residue after the drop evaporates[1]. The second flow is Benard convection, driven by surface tension gradients on the drop[2,3]. In our experiments, an insoluble monolayer of pentadecanoic acid is spread at the interface of a pendant drop. The surface tension is recorded, and the drop is deposited on a well-defined solid substrate. Fluorescent images of the surface phase of the surfactant are recorded as the drop evaporates. The surfactant monolayer assumes a variety of surface states as a function of the area per molecule at the interface: surface gaseous, surface liquid expanded, and surface liquid condensed phases[4]. Depending upon the surface state of the surfactant as the drop evaporates, transitions of residue patterns left by the particles occur, from the coffee ring pattern to Benard cells to irregular patterns, suggesting a strong resistance to outward flow are observed. The occurrence of Benard cells on a surfactant-rich interface occurs when the interface is in LE-LC coexistence. Prior research concerning surfactant effects on this instability predict that surfactants are strongly stabilizing[5]. The mechanisms for this change in behavior

Leak Detection Modeling and Simulation for Oil Pipeline with Artificial Intelligence Method

Directory of Open Access Journals (Sweden)

Pudjo Sukarno

2007-05-01

Full Text Available Leak detection is always interesting research topic, where leak location and leak rate are two pipeline leaking parameters that should be determined accurately to overcome pipe leaking problems. In this research those two parameters are investigated by developing transmission pipeline model and the leak detection model which is developed using Artificial Neural Network. The mathematical approach needs actual leak data to train the leak detection model, however such data could not be obtained from oil fields. Therefore, for training purposes hypothetical data are developed using the transmission pipeline model, by applying various physical configuration of pipeline and applying oil properties correlations to estimate the value of oil density and viscosity. The various leak locations and leak rates are also represented in this model. The prediction of those two leak parameters will be completed until the total error is less than certain value of tolerance, or until iterations level is reached. To recognize the pattern, forward procedure is conducted. The application of this approach produces conclusion that for certain pipeline network configuration, the higher number of iterations will produce accurate result. The number of iterations depend on the leakage rate, the smaller leakage rate, the higher number of iterations are required. The accuracy of this approach is clearly determined by the quality of training data. Therefore, in the preparation of training data the results of pressure drop calculations should be validated by the real measurement of pressure drop along the pipeline. For the accuracy purposes, there are possibility to change the pressure drop and fluid properties correlations, to get the better results. The results of this research are expected to give real contribution for giving an early detection of oil-spill in oil fields.

Effect of the inclusion of fish residue oils in diets on the fatty acid profile of muscles of males and females lambari (Astyanax altiparanae

Directory of Open Access Journals (Sweden)

Ligia Uribe Gonçalves

2012-09-01

Full Text Available This study evaluated the effects of two lipids sources of fish residue (tilapia and salmon compared with a vegetable oil source (soybean oil on the fatty acid profiles of male and female lambari. This experiment was developed in a completely randomized experimental design in a 3 × 2 factorial arrangement, totaling 6 treatments resulting from the combination of the three experimental diets for both sexes, with four replications for each treatment. This study involved 120 male (2.58±0.13 g and 72 female lambari (4.00±0.09 g, fed the experimental diets twice a day until apparent satiation for a period of 60 days. Oleic, linoleic, palmitic and stearic fatty acids were found at higher concentrations in all experimental oils and diets, as well in the muscle of male and female lambari. The low amounts of arachidonic, eicosapentaenoic and docosahexaenoic acids in the experimental diets and subsequent greater concentrations in muscle tissue, suggested that lambari are able to desaturate and elongate the chain of fatty acids with 18 carbons. The fish of both sexes that received the diet with soybean oil showed high levels of n-6 fatty acids, especially of C18: 2n-6 and low levels of eicosapentaenoic and docosahexaenoic acids. The diet with salmon residue oil promoted higher levels of fatty acids of the n-3 series and resulted in the best n-3/n-6 ratio in the muscle of male and female lambari. The oils from fish residues can be a substitute for traditional fish oil and its use in the lambari diets does not impair its growth.

Dual-fuel production from restaurant grease trap waste: bio-fuel oil extraction and anaerobic methane production from the post-extracted residue.

Science.gov (United States)

Kobayashi, Takuro; Kuramochi, Hidetoshi; Maeda, Kouji; Tsuji, Tomoya; Xu, Kaiqin

2014-10-01

An effective way for restaurant grease trap waste (GTW) treatment to generate fuel oil and methane by the combination of physiological and biological processes was investigated. The heat-driven extraction could provide a high purity oil equivalent to an A-grade fuel oil of Japanese industrial standard with 81-93 wt% of extraction efficiency. A post-extracted residue was treated as an anaerobic digestion feedstock, and however, an inhibitory effect of long chain fatty acid (LCFA) was still a barrier for high-rate digestion. From the semi-continuous experiment fed with the residual sludge as a single substrate, it can be concluded that the continuous addition of calcium into the reactor contributed to reducing LCFA inhibition, resulting in the long-term stable operation over one year. Furthermore, the anaerobic reactor performed well with 70-80% of COD reduction and methane productivity under an organic loading rate up to 5.3g-COD/L/d. Copyright © 2014 Elsevier Ltd. All rights reserved.

The variability in iron speciation in size fractionated residual oil fly ash particulate matter (ROFA PM).

Science.gov (United States)

Pattanaik, Sidhartha; Huggins, Frank E; Huffman, Gerald P

2016-08-15

Ambient particulate matter (PM) containing iron can catalyze Fenton reaction leading to the production of reactive oxygen species in cells. It can also catalyze atmospheric redox reaction. These reactions are governed by the physicochemical characteristics of iron in ambient PM. As a surrogate for ambient PM, we prepared residual oil fly ash PM (ROFA PM) in a practical fire tube boiler firing residual oils with varying sulfur and ash contents. The ROFA particles were resolved into fine PM or PM2.5 (aerodynamic diameter (AD)iron speciation in PM2.5+ was ascertained using X-ray absorption spectroscopy and leaching method while that in PM2.5 was reported earlier. The results of both studies are compared to get an insight into the variability in the iron speciation in different size fractions. The results show the predominance of ferric sulfate, with a minor spinal ferrite in both PM (i.e. ZnxNi1-xFe2O4 in PM2.5, ZnFe2O4 in PM2.5+). The iron solubility in ROFA PM depends on its speciation, mode of incorporation of iron into particle's carbonaceous matrix, the grade and composition of oils, and pH of the medium. The soluble fraction of iron in PM is critical in assessing its interaction with the biological systems and its toxic potential. Copyright © 2016 Elsevier B.V. All rights reserved.

Comprehensive profiling and marker identification in non-volatile citrus oil residues by mass spectrometry and nuclear magnetic resonance.

Science.gov (United States)

Marti, Guillaume; Boccard, Julien; Mehl, Florence; Debrus, Benjamin; Marcourt, Laurence; Merle, Philippe; Delort, Estelle; Baroux, Lucie; Sommer, Horst; Rudaz, Serge; Wolfender, Jean-Luc

2014-05-01

The detailed characterization of cold-pressed lemon oils (CPLOs) is of great importance for the flavor and fragrance (F&F) industry. Since a control of authenticity by standard analytical techniques can be bypassed using elaborated adulterated oils to pretend a higher quality, a combination of advanced orthogonal methods has been developed. The present study describes a combined metabolomic approach based on UHPLC-TOF-MS profiling and (1)H NMR fingerprinting to highlight metabolite differences on a set of representative samples used in the F&F industry. A new protocol was set up and adapted to the use of CPLO residues. Multivariate analysis based on both fingerprinting methods showed significant chemical variations between Argentinian and Italian samples. Discriminating markers identified in mixtures belong to furocoumarins, flavonoids, terpenoids and fatty acids. Quantitative NMR revealed low citropten and high bergamottin content in Italian samples. The developed metabolomic approach applied to CPLO residues gives some new perspectives for authenticity assessment. Copyright © 2013 Elsevier Ltd. All rights reserved.

Greenhouse gas reductions through enhanced use of residues in the life cycle of Malaysian palm oil derived biodiesel

DEFF Research Database (Denmark)

Hansen, Sune Balle; Olsen, Stig Irving; Ujang, Zaini

2012-01-01

This study identifies the potential greenhouse gas (GHG) reductions, which can be achieved by optimizing the use of residues in the life cycle of palm oil derived biodiesel. This is done through compilation of data on existing and prospective treatment technologies as well as practical experiments...... extraction from empty fruit bunches was found to be the most significant in the biodiesel production life cycle. All the studied waste treatment technologies performed significantly better than the conventional practices and with dedicated efforts of optimized use in the palm oil industry, the production...

Reusing a residue of the oil industry (FCC) in the production of building elements

OpenAIRE

Caicedo Casso, Eduard Andrés; Universidad del Valle; Mejía de Gutiérrez, Ruby; Universidad del Valle; Gordillo Suárez, Marisol; Universidad Autónoma de Occidente; Torres Agredo, Janneth; Universidad Nacional de Colombia, sede Palmira

2015-01-01

This paper analyzes the feasibility of using a residue of spent catalyst (FCC) of the cracking process, from a Colombian oil company, in the production of building elements such as locks and pavers. To define the optimal mix of portland cement/FCC, Portland cement mortars with FCC ratios between 0 and 70% as replacement of cement were prepared and its compressive strength is evaluated at ages up to 28 days of curing. Using a statistical processing, applying the methodology of response, the pr...

Assessment of bioavailability of weathered oil residues using caged bivalves (Crassostrea gigas and Mytilus edulis) as indicator organisms

International Nuclear Information System (INIS)

Bleczinski, C.F.; Costa, H.J.; Rigatti, M.J.; Wong, M.C.; Boehm, P.D.

1993-01-01

In April 1988, an estimated 400,000 gallons of San Joaquin Valley crude oil spilled into Peyton Slough and subsequently into Suisun Bay from an oil refinery in Martinez, California. The crude oil initially impacted a number of ecologically sensitive environments including estuarine water, marsh grasses, marsh and shoreline sediment, and intertidal sediment. A four-year oil weathering study was performed to determine the concentrations of environmentally important compounds in the stranded oil, to monitor changes in these concentrations over time, and to assess the potential long-term impact of the spilled oil in these various environments. As a result of marked differences in the rate of weathering at the different sites, a bioaccumulation component was added to the original study design in order to assess the bioavailability of crude oil residues remaining four-years post spill. Caged bivalves (Crassostrea gigas and Mytilus edulis) were deployed at the three study sites as sentinel organisms and exposed for three months. Sediments and organism tissues were analyzed using gas chromatography/mass spectrometry for polynuclear aromatic hydrocarbon (PAH) assemblages characteristics of the spilled oil. Advanced hydrocarbon fingerprinting techniques (e.g., double ratio plots of characteristic alkyl PAHs) were used to match distributions in the organisms and in the study site sediments

24 hydrocarbon degradation in poultry droppings and cassava peels

African Journals Online (AJOL)

OLUWOLE AKINNAGBE

2009-01-01

Jan 1, 2009 ... This greenhouse study was aimed at determining the potentials of poultry droppings (PD) and cassava peels ... shift in the composition of bacterial community to ..... Oil and Gas Journal. pp. ... Prentice-Hall of India Private Ltd.

Oxidizing oils, etc. [British patent

Energy Technology Data Exchange (ETDEWEB)

Penniman, W B.D.

1926-03-02

The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tar, and oils containing powdered coal, coke or peat, sulphur in suspension, is effected by passing air or other oxygen-containig gas through a layer of the material of a depth sufficient substantially to deoxygenate the air, the pressure being at or below atmospheric pressure.

Gasification of coal as efficient means of environment protection and hydrogenation of heavy oils residues

Energy Technology Data Exchange (ETDEWEB)

Krichko, A.A.; Maloletnev, A.S. [Fossil Fuel Institute, Moscow (Russian Federation)

1995-12-31

The Russia`s more then 50% of coals produced in its European part contain over 2,5% of sulphur, and the coals containing less than 1.5% of sulphurs comprise ca.20%. Thus, utilisation of the sulphide coals is inevitable, and there a problem arises concerning the technology of their sensible use and considering the requirements on the environment protection. Russia`s specialists have developed a design and construction for a steam-gas installation with a closed cycle gasification of the solid fuel. The gasification process will proceed in the fluidized bed under forced pressure of the steam-air blast. Characteristic features of this process are the following: a higher efficiency (the capacity of one gas generator is 3-3,5 times larger than that attained in the present gas generators of the Lurgy`s type): 2-2,5 times decreased fuel losses as compared to the Winkler`s generators; retention of the sensible heat, resulting in an increased total energy efficiency. The main task for petroleum refining industry at the present stage is the increase of depth of oil processing with the aim to intensify motor fuel production. One of the ways to solve the problem is to involve heavy oil residues into the processing. But the high metal and asphaltenes contents in the latter make the application of traditional methods and processes more difficult. Up to now there is no simple and effective technology which could give the opportunity to use oil residues for distillate fractions production. In Fossil fuel institute a process for hydrogenation of high boiling oil products, including with high sulphur, vanadium and nickel contents ones, into distillates and metals concentrates. The main point of the new process is as follows: the water solution of catalytic additive, for which purpose water soluble metal salts of VI-VIII groups are used, is mixed with tar, dispersed and then subjected to additional supercavitation in a special apparatus.

Effects of oil and oil burn residues on seabird feathers

DEFF Research Database (Denmark)

Fritt-Rasmussen, Janne; Linnebjerg, Jannie Fries; Sørensen, Martin X.

2016-01-01

It is well known, that in case of oil spill, seabirds are among the groups of animals most vulnerable. Even small amounts of oil can have lethal effects by destroying the waterproofing of their plumage, leading to loss of insulation and buoyancy. In the Arctic these impacts are intensified...

Analysis of Nova 1 strategy formed by barrier options and its application in hedging against a price drop in oil market

Directory of Open Access Journals (Sweden)

Michal Šoltés

2015-12-01

Full Text Available This paper investigates hedging analysis against an underlying price drop by using the Nova 1 strategy formed by standard vanilla and barrier options. There are used European down and knock-in put options together with barrier call options. Derived income functions from the secured positions in analytical expressions are presented. Based on the theoretical results, the hedged portfolio is applied to SPDR SandP Oil and Gas Exploration and Production ETF. The proposed hedging variants are analysed and compared with the recommendation of the best possibilities for investors.

Measuring the aerial application of oil dispersant from very large aircraft at moderate altitude

International Nuclear Information System (INIS)

Fay, R.R.; Giammona, C.P.; Binkley, K.; Engelhardt, F.R.

1993-01-01

As part of a study of various aspects of oil dispersant application technology, a comparison study was conducted employing the Airborne Dispersant Delivery System (ADDS) pack and the Modular Aerial Spray System (MASS) in C-130 Hercules aircraft at altitudes of 50-150 ft above ground and at speeds up to 200 knots. Dyed Corexit 9527 was applied at a target dose rate of 5 gal/acre over a collection grid composed of metal trays, Kromekote cards, oil-sensitive cards, a continuous trough, and a WRK string collector. Analysis of the collected dispersant was done by colorimetry, fluorometry, and image analysis. Correlations through the different methodologies demonstrated that high speed, moderate altitude application of oil dispersant could be successful in delivering dispersant to the surface at effective concentration and drop size. Environmental studies of the test area showed no residual dispersant in the soil following cessation of spraying. 1 ref

In Situ Biodiesel Production from Residual Oil Recovered from Spent Bleaching Earth

Directory of Open Access Journals (Sweden)

Ramli Mat

2011-05-01

Full Text Available Currently, semi-refined and refined vegetable oils are used as a feedstock in biodiesel production. However, due to competition with conventional fossil fuel, economic reasons, shortage supply of food and its social impact on the global scale has somewhat slowed the development of biodiesel industry. Studies have been conducted to recover oil from mill palm oil operation especially from the spent bleaching earth. Hence, the study was to investigate the potential recovery of oil from spent bleaching earth to be used as a feedstock for biodiesel production. The effect of different types of catalysts (sodium hydroxide alkali and sulfuric acid catalysts on biodiesel yield was studied. In addition, the effect of volume addition of methanol to the weight of spent bleaching earth on the product yield was also studied. Furthermore, the effect of ratio of hexane to methanol was also carried out to determine its product yield. The studies were carried out in an in-situ biodiesel reactor system and the biodiesel product was analyzed using gas chromatography mass spectrometry. Result shows that the use of alkali catalyst produced the highest yield of biodiesel and the most optimum biodiesel yield was obtained when the methanol to spent bleaching earth ratio was 3.2:1 (gram of methanol: gram of SBE and hexane to methanol ratio of 0.6:1 (volume of hexane: volume of methanol. © 2011 BCREC UNDIP. All rights reserved(Received: 19th December 2010, Revised: 10th May 2011; Accepted: 18th May 2011[How to Cite: R. Mat, O.S. Ling, A. Johari, M. Mohamed. (2011. In Situ Biodiesel Production from Residual Oil Recovered from Spent Bleaching Earth. Bulletin of Chemical Reaction Engineering & Catalysis, 6(1: 53-57. doi:10.9767/bcrec.6.1.678.53-57][How to Link / DOI: http://dx.doi.org/10.9767/bcrec.6.1.678.53-57 || or local:  http://ejournal.undip.ac.id/index.php/bcrec/article/view/678 ] | View in 

Shale oil. I. Genesis of oil shales and its relation to petroleum and other fuels

Energy Technology Data Exchange (ETDEWEB)

McKee, R H; Manning, P D.V.

1927-01-01

Oil-shale kerogen originated from resinous vegetation residues of past eras, whereas well petroleum was formed from oil shales by pressure and mild heat. Petroleum migrated to its present reservoir from neighboring oil-shale deposits, leaving a residue of black bituminous shales. The high carbon dioxide content of gases present in petroleum wells originated from kerogen, as it gives off carbon dioxide gas before producing soluble oil or bitumen.

Application of environmental management system for a energetic plant with oil residual biomass; Aplicacion de un sistema de gestion medio ambiental a una planta generadora de energia que utiliza la biomasa residual del olivar

Energy Technology Data Exchange (ETDEWEB)

Linan Veganzones, M.J.; Soca Olazabal, N.; Pizarro Camacho, D

1998-12-01

Being the alpechin one of the most contaminant residues by the mediterranean agrarian industry, as of today there is no integral depuration procedure. In this paper we show the innovative approach being used to eliminate the alpechin along with the oil miller residual biomass. What it more, the only agroindustrial complex which has introduced such approach is using an EMAS so that actual achievements could be realistically measured. (Author) 12 refs.

Oil price, biofuels and food supply

International Nuclear Information System (INIS)

Timilsina, Govinda R.; Mevel, Simon; Shrestha, Ashish

2011-01-01

The price of oil could play a significant role in influencing the expansion of biofuels, but this issue has yet to be fully investigated in the literature. Using a global computable general equilibrium (CGE) model, this study analyzes the impact of oil price on biofuel expansion, and subsequently, on food supply. The study shows that a 65% increase in oil price in 2020 from the 2009 level would increase the global biofuel penetration to 5.4% in 2020 from 2.4% in 2009. If oil prices rise 150% from their 2009 levels by 2020, the resulting penetration of biofuels would be 9%, which is higher than that would be caused by current mandates and targets introduced in more than forty countries around the world. The study also shows that aggregate agricultural output drops due to an oil price increase, but the drop is small in major biofuel producing countries as the expansion of biofuels would partially offset the negative impacts of the oil price increase on agricultural outputs. An increase in oil price would reduce global food supply through direct impacts as well as through the diversion of food commodities and cropland towards the production of biofuels. - Highlights: ► A global CGE model to analyze impacts of oil price on biofuels and food supply. ► Global biofuel penetration increases from 2.4% (2009) to 5.4% (2020) in baseline. ► A 150% rise of oil price boosts biofuels more than current mandates and targets do. ► Biofuels partially offset drops in agricultural outputs caused by oil price rise. ► Biofuels as well as oil price rise negatively affect global food supply.

The oil market towards 2030 - can OPEC combine high oil price with high market share

International Nuclear Information System (INIS)

Aune, Finn Roar; Glomsroed, Solveig; Lindholt, Lars; Rosendahl, Knut Einar

2005-01-01

In this paper we examine within a partial equilibrium model for the oil market whether OPEC can combine high oil prices with a high market share. The oil market model explicitly accounts for reserves, development and production in 4 field categories across 13 regions. Oil companies may invest in new field development or alternatively on improved oil recovery in the decline phase of fields in production. Non-OPEC production is profit-driven, whereas OPEC meets the residual call for OPEC oil at a pre-specified oil price, while maintaining a surplus capacity. The model is run over a range of exogenous oil prices from 15 to 60 $ per barrel. Sustained high oil prices stimulate Non-OPEC production, but its remaining reserves gradually diminish despite new discoveries. Oil demand is only slightly affected by higher prices. Thus, OPEC is able to keep and eventually increase its current market share beyond 2010 even with oil prices around $30 per barrel. In fact, the model simulations indicate that an oil price around $40 is profitable for OPEC, even in the long term. Sensitivity analyses show that the most profitable price level for OPEC is generally above $35 per barrel. Even with several factors working jointly in OPEC's disfavour, the oil price seems to stick to the 30 $ level. Thus, for OPEC there is a trade-off between high prices and high market share in the short to medium term, but not in the long term. For OECD countries, on the other hand, there is a clear trade-off between low oil prices and low import dependence. (Author)

Levitating Drop in a Tilted Rotating Tank - Gallery of Fluid Motion Entry V044

OpenAIRE

White, Andrew; Swan, David; Ward, Thomas

2011-01-01

A cylindrical acrylic tank with inner diameter D = 4 in. is mounted such that its axis of symmetry is at some angle measured from the vertical plane. The mixing tank is identical to that described in [1] The tank is filled with 200 mL of 1000 cSt silicone oil and a 5 mL drop of de-ionized water is placed in the oil volume. The water drop is allowed to come to rest and then a motor rotates the tank about its axis of symmetry at a fixed frequency = 0.3 Hz. Therefore the Reynolds number is fixed...

Residues of 14C-cyolane in cottonseed products

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Osman, A.Z.; Fakhr, I.M.I.; Bahig, M.E.

1981-01-01

The systemic insecticide cyolane [2-(0,0-diethylphosphoryl)-imino-1,3-dithiolane] was prepared from 14 C-ethanol, phosphorus oxychloride and 2-amino-1,3-dithiolane. Cotton plants were treated with two applications of the insecticide under conditions of local agricultural practice. 14 C-residues in the crude oil and cake of the harvested cotton seeds amounted to 1.63 and 0.014 mg/kg respectively. About 50% of the 14 C-activity present in the crude oil was found to be eliminated by simulated commercial processes used for refining of the oil. Alkali treatment and bleaching removed 16% and 25% of the radioactive residues respectively. Winterization of the bleached oil at 5-7 0 C for 3 days effected a further elimination of 13%. 14 C-residues in the cotton seed products and in the samples of the refined oil were characterized and the main constituents identified using chromatographic techniques. (author)

Fabrication of simulated plate fuel elements: Defining role of out-of-plane residual shear stress

Energy Technology Data Exchange (ETDEWEB)

Rakesh, R., E-mail: rakesh.rad87@gmail.com [DAE Graduate Fellows, IIT Bombay, Powai, Mumbai 400076 (India); Metallic Fuels Division, BARC, Trombay, Mumbai 400085 (India); Kohli, D. [DAE Graduate Fellows, IIT Bombay, Powai, Mumbai 400076 (India); Metallic Fuels Division, BARC, Trombay, Mumbai 400085 (India); Sinha, V.P.; Prasad, G.J. [Metallic Fuels Division, BARC, Trombay, Mumbai 400085 (India); Samajdar, I. [Department of Metallurgical Engineering and Materials Science, IIT Bombay, Powai, Mumbai 400076 (India)

2014-02-01

Bond strength and microstructural developments were investigated during fabrication of simulated plate fuel elements. The study involved roll bonding of aluminum–aluminum (case A) and aluminum–aluminum + yttria (Y{sub 2}O{sub 3}) dispersion (case B). Case B approximated aluminum–uranium silicide (U{sub 3}Si{sub 2}) ‘fuel-meat’ in an actual plate fuel. Samples after different stages of fabrication, hot and cold rolling, were investigated through peel and pull tests, micro-hardness, residual stresses, electron and micro-focus X-ray diffraction. Measurements revealed a clear drop in bond strength during cold rolling: an observation unique to case B. This was related to significant increase in ‘out-of-plane’ residual shear stresses near the clad/dispersion interface, and not from visible signatures of microstructural heterogeneities.

All-Optical Regenerative OTDM Add/Drop Multiplexing at 40 Gbit/s using Monolithic InP Mach-Zehnder Interferometer

DEFF Research Database (Denmark)

Buxens, Alvaro A.; Clausen, Anders; Poulsen, Henrik Nørskov

2000-01-01

We report a novel method for simultaneous add-drop multiplexing in OTDM systems which includes regenerative capabilities and perfect clearing of the drop channel time slot. The principle has been demonstrated at 40 Gb/s showing an excellent performance.......We report a novel method for simultaneous add-drop multiplexing in OTDM systems which includes regenerative capabilities and perfect clearing of the drop channel time slot. The principle has been demonstrated at 40 Gb/s showing an excellent performance....

Preparation of function-enhanced vegetable oils

Directory of Open Access Journals (Sweden)

Hiroshi Maeda

2016-01-01

Full Text Available Background: Previously, we (HM found that most commercially available edible oils, which were processed by hexane extraction followed by a number of purification steps, were extremely low in anti-peroxy radical (ROO., or radical scavenging activity. This is a great contrast to the respective virgin oils as exemplified by extra-virgin olive oil or crude rape seed oil [1-4] (Figure 1. Therefore, such highly purified oils will became prooxidant and less desirable food components in terms of health oriented diet. Oxidized oils may eventually cause DNA cleavages, modification of proteins, RNA, and lipids, as well as cellular damage, or promote inflammation and carcinogenesis at later time [5-9]. These commercial oils of low antioxidant activity may be improved by adding functionally effective antioxidative components, by using dried vegetable-waste such as tomato-juice-waste-residues and wine-ferment-waste-residues. Their antioxiative components will be transferred into the functionally poor grade edible oils, and consequently, one can improve the quality of such functionally poor oils and thereby contributing human health [2,8,9]. The purpose of this paper is to report a practical procedure to fortify functionally low grade conventional edible oils to functionally enriched edible oils using dried vegetable-waste residues such as tomato juice waste, and wine-ferment-residues, or other vegetable-waste residues. Methods: (1 Preparation and measurements of lycopene and carotenoid enriched oils. To 5.0g or 1.0g of the dried residue of tomato juice waste, 100ml of commercial rape seed (canola oil was added respectively. Each mixture was incubated at room temperature in dark for several weeks. Amount of lycopene and carotenoids extracted into the oil was monitored by increase of absorption (400-550nm and fluorescence at 470nm of carotenoid. Grape-juice ferment (wine waste was similarly prepared after hot air drying, and immersed in canola oil. (2

The preparation of Drosophila embryos for live-imaging using the hanging drop protocol.

Science.gov (United States)

Reed, Bruce H; McMillan, Stephanie C; Chaudhary, Roopali

2009-03-13

Green fluorescent protein (GFP)-based timelapse live-imaging is a powerful technique for studying the genetic regulation of dynamic processes such as tissue morphogenesis, cell-cell adhesion, or cell death. Drosophila embryos expressing GFP are readily imaged using either stereoscopic or confocal microscopy. A goal of any live-imaging protocol is to minimize detrimental effects such as dehydration and hypoxia. Previous protocols for preparing Drosophila embryos for live-imaging analysis have involved placing dechorionated embryos in halocarbon oil and sandwiching them between a halocarbon gas-permeable membrane and a coverslip. The introduction of compression through mounting embryos in this manner represents an undesirable complication for any biomechanical-based analysis of morphogenesis. Our method, which we call the hanging drop protocol, results in excellent viability of embryos during live imaging and does not require that embryos be compressed. Briefly, the hanging drop protocol involves the placement of embryos in a drop of halocarbon oil that is suspended from a coverslip, which is, in turn, fixed in position over a humid chamber. In addition to providing gas exchange and preventing dehydration, this arrangement takes advantage of the buoyancy of embryos in halocarbon oil to prevent them from drifting out of position during timelapse acquisition. This video describes in detail how to collect and prepare Drosophila embryos for live imaging using the hanging drop protocol. This protocol is suitable for imaging dechorionated embryos using stereomicroscopy or any upright compound fluorescence microscope.

Preparation of hydraulic cement from oil-shale

Energy Technology Data Exchange (ETDEWEB)

1921-08-28

A process for the preparation of hydraulic cement from oil-shale or oil-shale residue is characterized in that, the oil-shale or shale-coke together with a slight amount of marl is burned under sintering conditions and the residue obtained is ground to a fine dust.

Application of hydrochloric cyclopentolate eye drops in the mydriasis test and optometry for children with hyperopia

Directory of Open Access Journals (Sweden)

Hong-Ping Yin

2016-02-01

Full Text Available AIM:To observe and study the comprehensive application effect of hydrochloric cyclopentolate eye drops in the mydriasis test and optometry for children with hyperopia.METHODS:Eighty-four children with hyperopia who were intervened with mydriasis test and optometry in our hospital from February 2014 to March 2015 were selected as the research object,and they were intervened with mydriasis test and optometry by tropicamide or hydrochloric cyclopentolate eye drops. The diopter, pupil diameter and residual regulation before administration and at different time after administration of the two methods were compared,and the detected results of the two groups with different severity degree were compared too.RESULTS:The diopter, pupil diameter and residual regulation before administration of the two eye drops had no significant differences(all P>0.05,while the residual regulation after using hydrochloric cyclopentolate eye drops at 20, 40, 60min and 24h were all smaller than those after using tropicamide(all PP>0.05. The pupil diameter of the two groups at 48h after administration both had no significant differences to those before administration(all P>0.05.CONCLUSION:The comprehensive application effect of hydrochloric cyclopentolate eye drops in the mydriasis test and optometry of children with hyperopia is better,and its paralysis effect for ciliaris is obvious.

A Review of distribution and quantity of lingering subsurface oil from the Exxon Valdez Oil Spill

Science.gov (United States)

Nixon, Zachary; Michel, Jacqueline

2018-01-01

Remaining lingering subsurface oil residues from the Exxon Valdez oil spill (EVOS) are, at present, patchily distributed across the geologically complex and spatially extensive shorelines of Prince William Sound and the Gulf of Alaska. We review and synthesize previous literature describing the causal geomorphic and physical mechanisms for persistence of oil in the intertidal subsurface sediments of these areas. We also summarize previous sampling and modeling efforts, and refine previously presented models with additional data to characterize the present-day linear and areal spatial extent, and quantity of lingering subsurface oil. In the weeks after the spill in March of 1989, approximately 17,750 t of oil were stranded along impacted shorelines, and by October of 1992, only 2% of the mass of spilled oil was estimated to remain in intertidal areas. We estimate that lingering subsurface residues, generally between 5 and 20 cm thick and sequestered below 10-20 cm of clean sediment, are present over 30 ha of intertidal area, along 11.4 km of shoreline, and represent approximately 227 t or 0.6% of the total mass of spilled oil. These residues are typically located in finer-grained sand and gravel sediments, often under an armor of cobble- or boulder-sized clasts, in areas with limited groundwater flow and porosity. Persistence of these residues is correlated with heavy initial oil loading together with localized sheltering from physical disturbance such as wave energy within the beach face. While no longer generally bioavailable and increasingly chemically weathered, present removal rates for these remaining subsurface oil residues have slowed to nearly zero. The only remaining plausible removal mechanisms will operate over time scales of decades.

Organic material of the Messel oil shales

Energy Technology Data Exchange (ETDEWEB)

Jankowski, B.; Littke, R.

1986-05-01

According to chemism, the Messel oil shales belong to the Kerogen type II, formed by algae with additions of huminite detritus, i.e. residues of higher plants. This has been confirmed by the organo-petrographic studies reported. The oil shale deposits are characterised by their content of organic materials, the occurrence of a cream-coloured inertinite maceral, and of siderite. Hence, two facies can be clearly discriminated, the lower one containing relatively much organic material and the cream-coloured inertinite, but no siderite, and the upper facies exhibiting just the opposite. As the detritus is finely grained and quite uniform in content of huminite and silicate material, and only few spores and pollen have been found, there is reason to assume that the two facies represent sediments formed far from the border of the lake.

A tiered analytical protocol for the characterization of heavy oil residues at petroleum-contaminated hazardous waste sites

International Nuclear Information System (INIS)

Pollard, S.J.T.; Kenefick, S.L.; Hrudey, S.E.; Fuhr, B.J.; Holloway, L.R.; Rawluk, M.

1994-01-01

The analysis of hydrocarbon-contaminated soils from abandoned refinery sites in Alberta, Canada is used to illustrate a tiered analytical approach to the characterization of complex hydrocarbon wastes. Soil extracts isolated from heavy oil- and creosote-contaminated sites were characterized by thin layer chromatography with flame ionization detection (TLC-FID), ultraviolet fluorescence, simulated distillation (GC-SIMDIS) and chemical ionization GC-MS analysis. The combined screening and detailed analytical methods provided information essential to remedial technology selection including the extent of contamination, the class composition of soil extracts, the distillation profile of component classes and the distribution of individual class components within various waste fractions. Residual contamination was characteristic of heavy, degraded oils, consistent with documented site operations and length of hydrocarbon exposure at the soil surface

Estimation of pressure drop in gasket plate heat exchangers

Directory of Open Access Journals (Sweden)

Neagu Anisoara Arleziana

2016-06-01

Full Text Available In this paper, we present comparatively different methods of pressure drop calculation in the gasket plate heat exchangers (PHEs, using correlations recommended in literature on industrial data collected from a vegetable oil refinery. The goal of this study was to compare the results obtained with these correlations, in order to choose one or two for practical purpose of pumping power calculations. We concluded that pressure drop values calculated with Mulley relationship and Buonopane & Troupe correlation were close and also Bond’s equation gave results pretty close to these but the pressure drop is slightly underestimated. Kumar correlation gave results far from all the others and its application will lead to oversize. In conclusion, for further calculations we will chose either the Mulley relationship or the Buonopane & Troupe correlation.

Insecticides authorized for use on olive trees and the relationship between their registration and residues in olive oil

Directory of Open Access Journals (Sweden)

Lentza-Rizos, Ch.

1996-12-01

Full Text Available In order to eliminate losses due to insect attack, several insecticides are used on olive trees. Their residues in olive oil constitute an important parameter of its quality and must be monitored regularly and kept as low possible in order to ensure consumer protection. In this paper the insecticides authorized for use on olive trees are listed and their ADIs and Codex Alimentarius MRLs reported. The existing registrations are discussed from the point of view of their residues in oil.

Diversos insecticidas son usados para eliminar las pérdidas debidas al ataque de insectos en olivos. Sus residuos en el aceite de oliva constituyen un parámetro importante de su calidad y deben ser controlados con regularidad y mantenidos tan bajos como sea posible en orden a asegurar la protección del consumidor. En este artículo se incluyen los distintos insecticidas autorizados para su uso en olivos así como los valores de ingesta diaria aceptable para el hombre y los límites máximos autorizados de los mismos. Los registros existentes se discuten desde el punto de vista de sus residuos en el aceite.

Residual Sorption and leaching of the herbicide diuron following de-oiled two-phase olive mill waste addition to soil

Energy Technology Data Exchange (ETDEWEB)

Lopez-Pineiro, A.; Albarran, A.; Cabrera, D.; Rato, J. M.; Munoz, A.; Flores, S.

2009-07-01

The residual sorption, desorption, degradation, and leaching of the herbicide diuron (3-(3,4-dichlorophenyl)-1,1-dimethylurea) a herbicide widely used in olive groves, was studied following the addition to soils of de oiled two-phase olive mill waste (DTPOMW). Field experiments were conducted on an olive grove soil amended over seven years with DTPOMW. (Author)

Residual Sorption and leaching of the herbicide diuron following de-oiled two-phase olive mill waste addition to soil

International Nuclear Information System (INIS)

Lopez-Pineiro, A.; Albarran, A.; Cabrera, D.; Rato, J. M.; Munoz, A.; Flores, S.

2009-01-01

The residual sorption, desorption, degradation, and leaching of the herbicide diuron (3-(3,4-dichlorophenyl)-1,1-dimethylurea) a herbicide widely used in olive groves, was studied following the addition to soils of de oiled two-phase olive mill waste (DTPOMW). Field experiments were conducted on an olive grove soil amended over seven years with DTPOMW. (Author)

Shape Oscillations of an Oil Drop Rising in Water : Effect of Surface Contamination

Czech Academy of Sciences Publication Activity Database

Abi Chebel, N.; Vejražka, Jiří; Masbernat, O.; Risso, F.

Roč. 702, JUL 10 ( 2012 ), s. 533-542 ISSN 0022-1120 R&D Projects: GA ČR GAP101/11/0806 Institutional support: RVO:67985858 Keywords : bubble dynamics * drops * drops and bubbles Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.183, year: 2012

Crude oil burning mechanisms

DEFF Research Database (Denmark)

van Gelderen, Laurens; Malmquist, L.M.V.; Jomaas, Grunde

2015-01-01

In order to improve predictions for the burning efficiency and the residue composition of in-situ burning of crude oil, the burning mechanism of crude oil was studied in relation to the composition of its hydrocarbon mixture, before, during and after the burning. The surface temperature, flame...... height, mass loss rate and residues of three hydrocarbon liquids (n-octane, dodecane and hexadecane), two crude oils (DUC and REBCO) and one hydrocarbon liquid mixture of the aforementioned hydrocarbon liquids were studied using the Crude Oil Flammability Apparatus. The experimental results were compared...... on the highest achievable oil slick temperature. Based on this mechanism, predictions can then be made depending on the hydrocarbon composition of the fuel and the measured surface temperature....

Global sensitivity analysis of Alkali-Surfactant-Polymer enhanced oil recovery processes

Energy Technology Data Exchange (ETDEWEB)

Carrero, Enrique; Queipo, Nestor V.; Pintos, Salvador; Zerpa, Luis E. [Applied Computing Institute, Faculty of Engineering, University of Zulia, Zulia (Venezuela)

2007-08-15

After conventional waterflooding processes the residual oil in the reservoir remains as a discontinuous phase in the form of oil drops trapped by capillary forces and is likely to be around 70% of the original oil in place (OOIP). The EOR method so-called Alkaline-Surfactant-Polymer (ASP) flooding has been proved to be effective in reducing the oil residual saturation in laboratory experiments and field projects through reduction of interfacial tension and mobility ratio between oil and water phases. A critical step for the optimal design and control of ASP recovery processes is to find the relative contributions of design variables such as, slug size and chemical concentrations, in the variability of given performance measures (e.g., net present value, cumulative oil recovery), considering a heterogeneous and multiphase petroleum reservoir (sensitivity analysis). Previously reported works using reservoir numerical simulation have been limited to local sensitivity analyses because a global sensitivity analysis may require hundreds or even thousands of computationally expensive evaluations (field scale numerical simulations). To overcome this issue, a surrogate-based approach is suggested. Surrogate-based analysis/optimization makes reference to the idea of constructing an alternative fast model (surrogate) from numerical simulation data and using it for analysis/optimization purposes. This paper presents an efficient global sensitivity approach based on Sobol's method and multiple surrogates (i.e., Polynomial Regression, Kriging, Radial Base Functions and a Weighed Adaptive Model), with the multiple surrogates used to address the uncertainty in the analysis derived from plausible alternative surrogate-modeling schemes. The proposed approach was evaluated in the context of the global sensitivity analysis of a field scale Alkali-Surfactant-Polymer flooding process. The design variables and the performance measure in the ASP process were selected as slug size

40 CFR 279.47 - Management of residues.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 26 2010-07-01 2010-07-01 false Management of residues. 279.47 Section 279.47 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED... Management of residues. Transporters who generate residues from the storage or transport of used oil must...

Measurement of interfacial tension by use of pendant drop video techniques

Science.gov (United States)

Herd, Melvin D.; Thomas, Charles P.; Bala, Gregory A.; Lassahn, Gordon D.

1993-09-01

This report describes an instrument to measure the interfacial tension (IFT) of aqueous surfactant solutions and crude oil. The method involves injection of a drop of fluid (such as crude oil) into a second immiscible phase to determine the IFT between the two phases. The instrument is composed of an AT-class computer, optical cell, illumination, video camera and lens, video frame digitizer board, monitor, and software. The camera displays an image of the pendant drop on the monitor, which is then processed by the frame digitizer board and non-proprietary software to determine the IFT. Several binary and ternary phase systems were taken from the literature and used to measure the precision and accuracy of the instrument in determining IFT's. A copy of the software program is included in the report. A copy of the program on diskette can be obtained from the Energy Science and Technology Software Center, P.O. Box 1020, Oak Ridge, TN 37831-1020. The accuracy and precision of the technique and apparatus presented is very good for measurement of IFT's in the range from 72 to 10(exp -2) mN/m, which is adequate for many EOR applications. With modifications to the equipment and the numerical techniques, measurements of ultralow IFT's (less than 10(exp -3) mN/m) should be possible as well as measurements at reservoir temperature and pressure conditions. The instrument has been used at the Idaho National Engineering Laboratory to support the research program on microbial enhanced oil recovery. Measurements of IFT's for several bacterial supernatants and unfractionated acid precipitates of microbial cultures containing biosurfactants against medium to heavy crude oils are reported. These experiments demonstrate that the use of automated video imaging of pendant drops is a simple and fast method to reliably determine interfacial tension between two immiscible liquid phases, or between a gas and a liquid phase.

Life-Cycle Assessment of Pyrolysis Bio-Oil Production*

Energy Technology Data Exchange (ETDEWEB)

Steele, Philip; Puettmann, Maureen E.; Penmetsa, Venkata Kanthi; Cooper, Jerome E.

2012-07-01

As part ofthe Consortium for Research on Renewable Industrial Materials' Phase I life-cycle assessments ofbiofuels, lifecycle inventory burdens from the production of bio-oil were developed and compared with measures for residual fuel oil. Bio-oil feedstock was produced using whole southern pine (Pinus taeda) trees, chipped, and converted into bio-oil by fast pyrolysis. Input parameters and mass and energy balances were derived with Aspen. Mass and energy balances were input to SimaPro to determine the environmental performance of bio-oil compared with residual fuel oil as a heating fuel. Equivalent functional units of 1 MJ were used for demonstrating environmental preference in impact categories, such as fossil fuel use and global warming potential. Results showed near carbon neutrality of the bio-oil. Substituting bio-oil for residual fuel oil, based on the relative carbon emissions of the two fuels, estimated a reduction in CO2 emissions by 0.075 kg CO2 per MJ of fuel combustion or a 70 percent reduction in emission over residual fuel oil. The bio-oil production life-cycle stage consumed 92 percent of the total cradle-to-grave energy requirements, while feedstock collection, preparation, and transportation consumed 4 percent each. This model provides a framework to better understand the major factors affecting greenhouse gas emissions related to bio-oil production and conversion to boiler fuel during fast pyrolysis.

Fuel oil and kerosene sales 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-08-01

The Fuel Oil and Kerosene Sales 1997 report provides information, illustrations and state-level statistical data on end-use sales of kerosene; No. 1, No. 2, and No. 4 distillate fuel oil; and residual fuel oil. State-level kerosene sales include volumes for residential, commercial, industrial, farm, and all other uses. State-level distillate sales include volumes for residential, commercial, industrial, oil company, railroad, vessel bunkering, military, electric utility, farm, on-highway, off highway construction, and other uses. State-level residual fuel sales include volumes for commercial, industrial, oil company, vessel bunkering, military, electric utility, and other uses. 24 tabs.

Fuel oil and kerosene sales 1997

International Nuclear Information System (INIS)

1998-08-01

The Fuel Oil and Kerosene Sales 1997 report provides information, illustrations and state-level statistical data on end-use sales of kerosene; No. 1, No. 2, and No. 4 distillate fuel oil; and residual fuel oil. State-level kerosene sales include volumes for residential, commercial, industrial, farm, and all other uses. State-level distillate sales include volumes for residential, commercial, industrial, oil company, railroad, vessel bunkering, military, electric utility, farm, on-highway, off highway construction, and other uses. State-level residual fuel sales include volumes for commercial, industrial, oil company, vessel bunkering, military, electric utility, and other uses. 24 tabs

Antioxidant activity of rosemary essential oil fractions obtained by molecular distillation and their effect on oxidative stability of sunflower oil.

Science.gov (United States)

Mezza, Gabriela N; Borgarello, Ana V; Grosso, Nelson R; Fernandez, Héctor; Pramparo, María C; Gayol, María F

2018-03-01

The objective of this study was to evaluate the antioxidant activity of rosemary essential oil fractions obtained by molecular distillation (MD) and investigate their effect on the oxidative stability of sunflower oil. MD fractions were prepared in a series of low-pressure stages where rosemary essential oil was the first feed. Subsequently, a distillate (D1) and residue (R1) were obtained and the residue fraction from the previous stage used as the feed for the next. The residue fractions had the largest capacity to capture free radicals, and the lowest peroxide values, conjugated dienes and conjugated trienes. The antioxidant activity of the fractions was due to oxygenated monoterpenes, specifically α-terpineol and cis-sabinene hydrate. Oxidative stability results showed the residues (R1 and R4) and butylated hydroxytoluene had greater antioxidant activity than either the distillate fractions or original rosemary essential oil. The residue fractions obtained by short path MD of rosemary essential oil could be used as a natural antioxidants by the food industry. Copyright © 2017. Published by Elsevier Ltd.

Soil and vegetation changes after clear-felling coniferous forests: effects of varying removal of logging residues

International Nuclear Information System (INIS)

Olsson, Bengt.

1995-01-01

Effects of the intensity of logging residue harvesting on soil nutrient status and ground vegetation cover were examined over a 16-year period in two series of field experiments in Sweden. Short-term effects of slash harvesting and stump removal on soil water chemistry were studied after clear-felling a Norway spruce (Picea abies (L.) Karst.) stand in SW Sweden. Soil water concentrations of NH4 + , and NO 3 - and K + were lower shortly after whole-tree harvesting (i.e. stem and slash harvesting) than shortly after conventional stem-only harvesting or complete tree harvesting (i.e. stem, slash and stump removal). However, 5 years later there were no longer differences in nutrient concentrations detected between treatments, and nutrient levels approached those normally found in drainage water from forest land. Similar studies focussed on long-term (16 years) effects were conducted on four coniferous forest sites in Sweden, two in north and the other two in the south. In each region one site was situated in a pure Scots pine stand (Pinus sylvestris L.) and the other in a pure Norway spruce stand. In general, the intensity of slash harvesting had no effect on the total pools of nitrogen or carbon in the soil. Furthermore, this study showed experimentally that the harvesting of logging residues results in long-term soil acidification and depletions of exchangeable base cations, manganese and zinc pools, which lead in turn to a reduction in base saturation levels. A major implication for practical forestry was that guidelines and recommendations concerning the large-scale utilization of logging residues should be based more on the nutritional and soil acidifying consequences of this practice than on its potential effect on soil organic matter storage. It would also be possible to mitigate the detrimental effects that slash harvesting has on site conditions by applying wood-ash or other nutrients in inorganic form. 53 refs, 4 figs, 4 tabs

Soil and vegetation changes after clear-felling coniferous forests: effects of varying removal of logging residues

Energy Technology Data Exchange (ETDEWEB)

Olsson, Bengt

1995-11-01

Effects of the intensity of logging residue harvesting on soil nutrient status and ground vegetation cover were examined over a 16-year period in two series of field experiments in Sweden. Short-term effects of slash harvesting and stump removal on soil water chemistry were studied after clear-felling a Norway spruce (Picea abies (L.) Karst.) stand in SW Sweden. Soil water concentrations of NH4{sup +}, and NO{sub 3}{sup -} and K{sup +} were lower shortly after whole-tree harvesting (i.e. stem and slash harvesting) than shortly after conventional stem-only harvesting or complete tree harvesting (i.e. stem, slash and stump removal). However, 5 years later there were no longer differences in nutrient concentrations detected between treatments, and nutrient levels approached those normally found in drainage water from forest land. Similar studies focussed on long-term (16 years) effects were conducted on four coniferous forest sites in Sweden, two in north and the other two in the south. In each region one site was situated in a pure Scots pine stand (Pinus sylvestris L.) and the other in a pure Norway spruce stand. In general, the intensity of slash harvesting had no effect on the total pools of nitrogen or carbon in the soil. Furthermore, this study showed experimentally that the harvesting of logging residues results in long-term soil acidification and depletions of exchangeable base cations, manganese and zinc pools, which lead in turn to a reduction in base saturation levels. A major implication for practical forestry was that guidelines and recommendations concerning the large-scale utilization of logging residues should be based more on the nutritional and soil acidifying consequences of this practice than on its potential effect on soil organic matter storage. It would also be possible to mitigate the detrimental effects that slash harvesting has on site conditions by applying wood-ash or other nutrients in inorganic form. 53 refs, 4 figs, 4 tabs

Hydrogenizing oils, asphalts, etc

Energy Technology Data Exchange (ETDEWEB)

1925-03-14

The hydrogenation of carbonaceous solids in presence of combined sulfur, e.g., sulfides as described in the parent specification is applied to the treatment of rock oils, shale oils, resins, ozokerite, asphalt, and the like, or fractions, residues, or acid sludge or other conversion products thereof, alone or mixed. Preferably the hydrogen or other reducing gas is in excess and under pressure, and is either circuited or led through a series of treatment vessels, hydrogen being added for that used. In an example, residues from American crude oil are passed continuously with hydrogen at 200 atmospheres and 450 to 500/sup 0/C over pressed precipitated cobalt sulfide, the issuing gases being cooled to condense the light oil produced.

Proceedings: 1993 fuel oil utilization workshop

International Nuclear Information System (INIS)

1994-08-01

The primary objective of the Workshop was to utilize the experiences of utility personnel and continue the interchange of information related to fuel oil issues. Participants also identified technical problem areas in which EPRI might best direct its efforts in research and development of fuel oil utilization and to improve oil-fired steam generating systems' performance. Speakers presented specific fuel projects conducted at their particular utilities, important issues in the utilization of fuel oil, studies conducted or currently in the process of being completed, and information on current and future regulations for fuel utilization. Among the major topics addressed at the 1993 Fuel Oil Utilization Workshop were burner and ESP improvements for the reduction of particulate and NO x emissions, practical experience in utilization of low API gravity residual fuel oils, the use of models to predict the spread of oil spills on land, implementing OPA 90 preparedness and response strategies planning, a report on the annual Utility Oil Buyers Conference, ASTM D-396 specification for No. 6 fuel oil, the utilization of Orimulsion reg-sign in utility boilers, recent progress on research addressing unburned carbon and opacity from oil-fired utility boilers, EPRI's hazardous air pollutant monitoring and implications for residual fuel oil, and the feasibility of toxic metals removal from residual fuel oils. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

Capillarity and wetting phenomena drops, bubbles, pearls, waves

CERN Document Server

Gennes, Pierre-Gilles; Quéré, David

2004-01-01

As I glance out my window in the early morning, I can see beads of droplets gracing a spider web. The film of dew that has settled on the threads is unstable and breaks up spontaneously into droplets. This phenomenon has implications for the treatment of textile fibers (the process known as "oiling"), glass, and carbon. It is no less important when applying mascara! I take my morning shower. The moment I step out, I dry off by way of evaporation (which makes me feel cold) and by dewetting (the process by which dry areas form spontaneously and expand on my skin). As I rush into my car under a pelting rain, my attention is caught by small drops stuck on my windshield. I also notice larger drops rolling down and others larger still that, like snails, leave behind them a trail of water. I ask myself what the difference is between these rolling drops and grains of sand tumbling down an incline. I wonder why the smallest drops remain stuck. The answers to such questions do help car manufacturers treat the surface o...

Ultrasound-assisted single-drop microextraction for the determination of cadmium in vegetable oils using high-resolution continuum source electrothermal atomic absorption spectrometry

Science.gov (United States)

Almeida, Jorge S.; Anunciação, Taiana A.; Brandão, Geovani C.; Dantas, Alailson F.; Lemos, Valfredo A.; Teixeira, Leonardo S. G.

2015-05-01

This work presents an ultrasound-assisted single-drop microextraction procedure for the determination of cadmium in vegetable oils using high-resolution continuum source electrothermal atomic absorption spectrometry. Some initial tests showed that the best extraction efficiency was obtained when using ultrasound instead of mechanical agitation, indicating that acoustic cavitation improved the extraction process. Nitric, hydrochloric and acetic acids were evaluated for use in the extraction process, and HNO3 gave the best results. A two-level full-factorial design was applied to investigate the best conditions for the extraction of Cd from the oil samples. The influences of the sonication amplitude, time and temperature of the extraction were evaluated. The results of the design revealed that all of the variables had a significant effect on the experimental results. Afterward, a Box-Behnken design was applied to determine the optimum conditions for the determination of cadmium in vegetable oil samples. According to a multivariate study, the optimum conditions were as follows: sonication amplitude of 60%, extraction time of 15 min, extraction temperature of 46 °C and 0.1 mol L- 1 HNO3 as the extractor solution. Under optimized conditions, the developed method allows for the determination of Cd in oil samples with a limit of quantification of 7.0 ng kg- 1. Addition and recovery experiments were performed in vegetable oil samples to evaluate the accuracy of the method, and the recoveries obtained varied from 90% to 115%. The samples were also analyzed after the acid digestion procedure, and the paired t-test (95% confidence level) did not show significant differences from the proposed method.

Hydrocarbons - In the era of low-cost oil

International Nuclear Information System (INIS)

Dupin, Ludovic; Delamarche, Myrtille; Cognasse, Olivier; De Jaegher, Thibaut; Fleitour, Gaelle

2015-01-01

A set of articles addresses the current context of low cost oil and steep drop in oil prices. Graphs illustrate the evolution of oil prices, of supply and demand, of exploitation costs. This drop is partly due to the high level of production in Russia, Iraq and USA. This context results in drastic reductions of investments by companies involved in the oil sector, and therefore in job reduction, and in reduction of service costs. These reductions impact actors of the seismic analysis sector. Other consequences are more positive for consumers and refiners, and a trend towards diversification and consolidation for operators. The chairman of Technip answers some questions on Technip activities, situation and strategy. The case of the petrochemical sector is also addressed

Flow of Hydrolysed Polyacrylamide Mother Liquor through Filter Bag: Detecting the Effects of Formulation and Process Properties on Pressure Drop

Directory of Open Access Journals (Sweden)

Zi-Ming Feng

2016-01-01

Full Text Available Hydrolysed polyacrylamide (HPAM mother liquor is mainly used to extract oil. The HPAM solution is needed to filter the impurity using a bag filter before it is injected into the oil well. Therefore, the pressure drop of HPAM mother liquor must be less than 0.02 MPa in the processing of impurity filtration. The influence factors on pressure drop need to be researched. In this work, the computational fluid dynamics program (CFD was used to research some key influence factors on pressure drop, such as porosity, outlet pressure of filter, inlet flow rate and viscosity of mother liquor. The simulation results indicated that with increasing porosity, outlet pressure, inlet flow rate and mother liquor viscosity, the pressure drop had increased after flowing through the filter bag.

Electrohydrodynamics of a concentric compound drop in an AC electric field

Science.gov (United States)

Soni, Purushottam; Thaokar, Rochish M.; Juvekar, Vinay A.

2018-03-01

The dynamics of a compound drop suspended in another immiscible fluid in the presence of an AC electric field is investigated experimentally and using analytical theory. A closed-form analytical expression for the mean deformation and amplitude of deformation at cyclical steady state is derived in the small deformation limit. Experiments were performed with 0.1M NaCl/castor oil compound drops suspended in highly viscous silicone oil. In this case, both the core and the shell deform into prolate spheroids. The effect of two independent variables was investigated, namely, the ratio of the core radius to the shell radius and the frequency (ω) of the applied AC field. In the limit of ω → 0, the present analytical model reduces to the DC electric field model for the compound drop. It was observed that the size of the core significantly affects the dynamics of the compound drop. The mean and the amplitude of deformation of the shell increase considerably with an increase in the radius ratio. Since the present model is valid for a small deviation from a spherical shape, an excellent quantitative agreement is found between analytical and experimental results at low deformation, whereas, at large deformation, the match is only qualitative. It was also observed that the relative phase difference between the core and the shell decreases with an increase in the radius ratio and frequency of the applied electric field.

Mineral oil

International Nuclear Information System (INIS)

Schult-Bornemann, Karl-Heinz

2015-01-01

The dominant theme in the world energy market was the fall in oil prices in 2014. From 115 US-$/bbl in June it dropped to below 50 US-$/bbl in January 2015. Thereby the shale oil revolution has had the strong impact on the global energy situation, to this point has been predicted for three years. Although no one could predict the exact height of the fall in oil prices, but with oil as a reserve currency for all other fuels, it has not only had an impact on the gas and coal prices, but other commodities, such as copper, have also yielded. About cause and effect, there is a lot of speculation - not all of which are supported by wisdom. [de

The Galeta Oil Spill. III. Chronic Reoiling, Long-term Toxicity of Hydrocarbon Residues and Effects on Epibiota in the Mangrove Fringe

Science.gov (United States)

Levings, Sally C.; Garrity, Stephen D.; Burns, Kathryn A.

1994-04-01

In April 1986, 75 000-100 000 barrels of medium-weight crude oil (˜ 10 000-13 500 metric tons) spilled into Bahía las Minas, a large mangrove-lined bay on the Caribbean coast of Panamá. Between 1986 and 1991, biological and chemical effects of this spill were studied. The epibiota of fringing mangroves ( Rhizophora mangle L.) were examined in three habitats: (1) the shoreward margins of reef flats that fronted the open sea, (2) the edges of channels and lagoons, and (3) the banks of streams and man-made cuts that drained interior mangroves or uplands into lagoons. Chemical analyses of bivalves collected from submerged prop roots (oysters and false mussels) and records of slicks and tarry deposits on artificial roots documented chronic reoiling. Each habitat was repeatedly oiled between 1986 and 1991, with petroleum residues identified as the oil spilled in 1986. There was a decline in the release of tarry oils recorded as slicks and on roots over time, but not in tissue burdens of hydrocarbons in bivalves. This suggested that the processes that released these different types of oil residues were at least partially independent and that toxic hydrocarbons were likely to be released from sediments over the long term. The submerged prop roots of fringing mangroves in each habitat had a characteristic epibiota. On the open coast, roots were covered with a diverse assemblage of sessile invertebrates and algae. In channels, the most abundant species on roots was the edible oyster Crassostrea virginica ( rhizophorae morph). In streams, the false mussel Mytilopsis sallei covered the most space on roots. Cover of sessile invertebrates was significantly reduced at oiled compared with unoiled sites on the open coast for 4 years after oiling, while oysters and false mussels were reduced in cover at oiled sites in channels and streams through at least 1991, when observations ended. False mussels transplanted from an unoiled stream to oiled and unoiled streams were

Refinery Upgrading of Hydropyrolysis Oil From Biomass

Energy Technology Data Exchange (ETDEWEB)

Roberts, Michael [Gas Technology Inst., Des Plaines, IL (United States); Marker, Terry [Gas Technology Inst., Des Plaines, IL (United States); Ortiz-Toral, Pedro [Gas Technology Inst., Des Plaines, IL (United States); Linck, Martin [Gas Technology Inst., Des Plaines, IL (United States); Felix, Larry [Gas Technology Inst., Des Plaines, IL (United States); Wangerow, Jim [Gas Technology Inst., Des Plaines, IL (United States); Swanson, Dan [Gas Technology Inst., Des Plaines, IL (United States); McLeod, Celeste [CRI Catalyst, Houston, TX (United States); Del Paggio, Alan [CRI Catalyst, Houston, TX (United States); Urade, Vikrant [CRI Catalyst, Houston, TX (United States); Rao, Madhusudhan [CRI Catalyst, Houston, TX (United States); Narasimhan, Laxmi [CRI Catalyst, Houston, TX (United States); Gephart, John [Johnson Timber, Hayward, WI (United States); Starr, Jack [Cargill, Wayzata, MN (United States); Hahn, John [Cargill, Wayzata, MN (United States); Stover, Daniel [Cargill, Wayzata, MN (United States); Parrish, Martin [Valero, San Antonio, TX (United States); Maxey, Carl [Valero, San Antonio, TX (United States); Shonnard, David [MTU, Friedrichshafen (Germany); Handler, Robert [MTU, Friedrichshafen (Germany); Fan, Jiquig [MTU, Friedrichshafen (Germany)

2015-08-31

Cellulosic and woody biomass can be converted to bio-oils containing less than 10% oxygen by a hydropyrolysis process. Hydropyrolysis is the first step in Gas Technology Institute’s (GTI) integrated Hydropyrolysis and Hydroconversion IH2®. These intermediate bio-oils can then be converted to drop-in hydrocarbon fuels using existing refinery hydrotreating equipment to make hydrocarbon blending components, which are fully compatible with existing fuels. Alternatively, cellulosic or woody biomass can directly be converted into drop-in hydrocarbon fuels containing less than 0.4% oxygen using the IH2 process located adjacent to a refinery or ethanol production facility. Many US oil refineries are actually located near biomass resources and are a logical location for a biomass to transportation fuel conversion process. The goal of this project was to work directly with an oil refinery partner, to determine the most attractive route and location for conversion of biorenewables to drop in fuels in their refinery and ethanol production network. Valero Energy Company, through its subsidiaries, has 12 US oil refineries and 11 ethanol production facilities, making them an ideal partner for this analysis. Valero is also part of a 50- 50 joint venture with Darling Ingredients called Diamond Green Diesel. Diamond Green Diesel’s production capacity is approximately 11,000 barrels per day of renewable diesel. The plant is located adjacent to Valero’s St Charles, Louisiana Refinery and converts recycled animal fats, used cooking oil, and waste corn oil into renewable diesel. This is the largest renewable diesel plant in the U.S. and has successfully operated for over 2 years For this project, 25 liters of hydropyrolysis oil from wood and 25 liters of hydropyrolysis oils from corn stover were produced. The hydropyrolysis oil produced had 4-10% oxygen. Metallurgical testing of hydropyrolysis liquids was completed by Oak Ridge National Laboratories (Oak Ridge) and showed the

Oxidizing oils, etc. [British patent

Energy Technology Data Exchange (ETDEWEB)

Penniman, W B.D.

1926-03-02

The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tars, and oils containing powdered coal, coke, oreat, sulphur in suspension, by passing air or other oxygen-containing gas through a layer of the material of a depth sufficient substantially to deoxygenate the air and c., is carried out in stages in a series of treatment zones, the pressure in at least one of the zones being above atmospheric pressre. The products of oxidation include acetaldehyde, propionaldehyde, formic, acetic, propionic, butyric, acrylic and phthalic acids, alcohols, acetone, solvents, gums, and substances adapted for use as motor fuels or burnign oils. The oxidizing gas may be enriched with oxygen or be diluted with steam, and its point of entry into the oil and c. layer may be varied to promote or retard settlement of suspended solids.

Advances in biofuel production from oil palm and palm oil processing wastes: A review

Directory of Open Access Journals (Sweden)

Jundika C. Kurnia

2016-03-01

Full Text Available Over the last decades, the palm oil industry has been growing rapidly due to increasing demands for food, cosmetic, and hygienic products. Aside from producing palm oil, the industry generates a huge quantity of residues (dry and wet which can be processed to produce biofuel. Driven by the necessity to find an alternative and renewable energy/fuel resources, numerous technologies have been developed and more are being developed to process oil-palm and palm-oil wastes into biofuel. To further develop these technologies, it is essential to understand the current stage of the industry and technology developments. The objective of this paper is to provide an overview of the palm oil industry, review technologies available to process oil palm and palm oil residues into biofuel, and to summarise the challenges that should be overcome for further development. The paper also discusses the research and development needs, technoeconomics, and life cycle analysis of biofuel production from oil-palm and palm-oil wastes.

Fuel oil and kerosene sales 1994

International Nuclear Information System (INIS)

1995-01-01

This publication contains the 1994 survey results of the ''Annual Fuel Oil and Kerosene Sales Report'' (Form EIA-821). This is the sixth year that the survey data have appeared in a separate publication. Prior to the 1989 report, the statistics appeared in the Petroleum Marketing Annual (PMA)for reference year 1988 and the Petroleum Marketing Monthly (PMM) for reference years 1984 through 1987. The 1994 edition marks the 11th annual presentation of the results of the ongoing ''Annual Fuel Oil and Kerosene Sales Report'' survey. Distillate and residual fuel oil sales continued to move in opposite directions during 1994. Distillate sales rose for the third year in a row, due to a growing economy. Residual fuel oil sales, on the other hand, declined for the sixth year in a row, due to competitive natural gas prices, and a warmer heating season than in 1993. Distillate fuel oil sales increased 4.4 percent while residual fuel oil sales declined 1.6 percent. Kerosene sales decreased 1.4 percent in 1994

Optimization of the protein concentration process from residual peanut oil-cake

Directory of Open Access Journals (Sweden)

Gayol, M. F.

2013-12-01

Full Text Available The objective of this study was to find the best process conditions for preparing protein concentrate from residual peanut oil-cake (POC. The study was carried out on POC from industrial peanut oil extraction. Different protein extraction and precipitation conditions were used: water/ flour ratio (10:1, 20:1 and 30:1, pH (8, 9 and 10, NaCl concentration (0 and 0.5 M, extraction time (30, 60 and 120 min, temperature (25, 40 and 60 °C, extraction stages (1, 2 and 3, and precipitation pH (4, 4.5 and 5. The extraction and precipitation conditions which showed the highest protein yield were 10:1 water/flour ratio, extraction at pH 9, no NaCl, 2 extraction stages of 30 min at 40 °C and precipitation at pH 4.5. Under these conditions, the peanut protein concentrate (PC contained 86.22% protein, while the initial POC had 38.04% . POC is an alternative source of protein that can be used for human consumption or animal nutrition. Therefore, it adds value to an industry residue.El objetivo de este trabajo fue encontrar las mejores condiciones para obtener un concentrado de proteínas a partir de la torta residual de maní (POC. El estudio se llevó a cabo en POC provenientes de la extracción industrial de aceite de maní. Se utilizaron distintas condiciones para la extracción y precipitación de proteínas: relación agua / harina (10:1, 20:1 y 30:1, pH de extracción (8, 9 y 10, concentración de NaCl (0 y 0,5 M, tiempo de extracción (30, 60 y 120 min, temperatura (25, 40 y 60 °C, número de etapas de extracción (1, 2 y 3, y el pH de precipitación (4, 4,5 y 5. Las condiciones de extracción y de precipitación que mostraron mayor rendimiento de proteína fueron: relación de 10:1 en agua / harina, pH de extracción de 9, en ausencia de NaCl, 2 etapas de extracción de 30 min cada una a 40 °C y el pH de precipitación de 4,5. En estas condiciones, el concentrado de proteína de maní (PC fue de 86,22%, mientras que el porcentaje de proteínas de

Drop splashing: the role of surface wettability and liquid viscosity

Science.gov (United States)

Almohammadi, Hamed; Amirfazli, Alidad; -Team

2017-11-01

There are seemingly contradictory results in the literature about the role of surface wettability and drop viscosity for the splashing behavior of a drop impacting onto a surface. Motivated by such issues, we conducted a systematic experimental study where splashing behavior for a wide range of the liquid viscosity (1-100 cSt) and surface wettability (hydrophilic to hydrophobic) are examined. The experiments were performed for the liquids with both low and high surface tensions ( 20 and 72 mN/m). We found that the wettability affects the splashing threshold at high or low contact angle values. At the same drop velocity, an increase of the viscosity (up to 4 cSt) promotes the splashing; while, beyond such value, any increase in viscosity shows the opposite effect. It is also found that at a particular combination of liquid surface tension and viscosity (e.g. silicone oil, 10 cSt), an increase in the drop velocity changes the splashing to spreading. We relate such behaviors to the thickness, shape, and the velocity of the drop's lamella. Finally, to predict the splashing, we developed an empirical correlation which covers all of the previous reported data, hence clarifying the ostensible existing contradictions.

The Other Major 2010 Oil Spill: Oil weathering after the Kalamazoo River Dilbit Spill

Science.gov (United States)

Swarthout, B.; Reddy, C. M.; Nelson, R. K.; Hamilton, S. K.; Aeppli, C.; Valentine, D. L.; Fundaun, S. E.; Oliveira, A. H.

2016-02-01

Diluted bitumen (dilbit) from the oil sands (tar sands) of western Canada is increasingly being transported to US markets. North America's largest inland oil spill and the first major oil sands spill in a freshwater environment occurred in 2010, when at least 843,000 gallons leaked from a pipeline into the Kalamazoo River of southwest Michigan. Cleanup of this oil was unusually difficult and protracted, lasting through 2014 and costing over a billion dollars, largely because a substantial fraction of the oil became submersed and deposited in slack water areas over 60 km of river channel, reservoirs, and floodplain backwaters. To investigate the fate of the spilled dilbit from the 2010 Kalamazoo River release, black rings, presumably oil residues, on the bark of dead trees were collected in 2015. These residues were deposited on the trees during high flood levels that have not been observed since the spill and represent an opportunity to constrain weathering processes excluding dissolution. This material contained a major non-GC amenable fraction of 90-95%, presumably oxygenated hydrocarbons. The GC amenable portion was consistent with laboratory weathered dilbit. We used a variety of analytical tools to characterize the dilbit residues, as well as to identify dilbit weathering processes that occurred since the spill.

Sliding behavior of oil droplets on nanosphere stacking layers with different surface textures

International Nuclear Information System (INIS)

Hsieh, Chien-Te; Wu, Fang-Lin; Chen, Wei-Yu

2010-01-01

Two facile coating techniques, gravitational sediment and spin coating, were applied for the creation of silica sphere stacking layers with different textures onto glass substrates that display various sliding abilities toward liquid drops with different surface tensions, ranged from 25.6 to 72.3 mN/m. The resulting silica surface exhibits oil repellency, long-period durability > 30 days, and oil sliding capability. The two-tier texture offers a better roll-off ability toward liquid drops with a wide range of γ L , ranged from 30.2 to 72.3 mN/m, i.e., when the sliding angle (SA) ad ) appears to describe the sliding behavior within the W ad region: 2.20-3.03 mN/m. The smaller W ad , the easier drop sliding (i.e., the smaller SA value) takes place on the surfaces. The W ad value ∼3.03 mN/m shows a critical kinetic barrier for drop sliding on the silica surfaces from stationary to movement states. This work proposes a mathematical model to simulate the sliding behavior of oil drops on a nanosphere stacking layer, confirming the anti-oil contamination capability.

Residual diesel measurement in sand columns after surfactant/alcohol washing

International Nuclear Information System (INIS)

Martel, R.; Gelinas, P.J.

1996-01-01

A new simple gravimetric technique has been designed to determine residual oil saturation of complex hydrocarbon mixtures (e.g., diesel) in sand column experiments because reliable methods are lacking. The He/N 2 technique is based on drying of sand columns by circulating helium gas to drag oil droplets in a cold trap (liquid nitrogen). With this technique, residual diesel measurement can be performed easily immediately after alcohol/surfactant washing and in the same lab. For high residual diesel content in Ottawa sand (25 to 30 g/kg), the technique is much more accurate (± 2% or 600 mg/kg) than the standard analytical methods for the determination of mineral oil and grease. The average relative error on partial diesel dissolution in sand column estimated after alcohol/surfactant flooding (residual saturation of 10 to 15 g/kg) is as low as 5%. The precision of the He/N 2 technique is adequate to compare relative efficiency of washing solutions when partial extraction of residual oil in Ottawa sand columns is performed. However, this technique is not adapted for determination of traces of oil in sediment or for environmental control of contaminated soils. Each diesel determination by the He/N 2 technique costs less than $8 in chemical products (helium and liquid nitrogen). A simple laboratory drying setup can be built for less than $400 which makes this technique valuable for diesel analyses when a large number of tests are required

CFD (Computational Fluid Dynamics) simulators and thermal cracking of heavy oil and ultraheavy residues using microreactor

Energy Technology Data Exchange (ETDEWEB)

Jardini, Andre L.; Bineli, Aulus R.R.; Viadana, Adriana M.; Maciel, Maria Regina Wolf; Maciel Filho, Rubens [State University of Campinas (UNICAMP), SP (Brazil). School of Chemical Engineering; Medina, Lilian C.; Gomes, Alexandre de O. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES); Barros, Ricardo S. [University Foundation Jose Bonifacio (FUJB), Rio de Janeiro, RJ (Brazil)

2008-07-01

In this paper, the design of microreactor with microfluidics channels has been carried out in Computer Aided Design Software (CAD) and constructed in rapid prototyping system to be used in chemical reaction processing of the heavy oil fractions. The flow pattern properties of microreactor (fluid dynamics, mixing behavior) have been considered through CFD (computational fluid dynamics) simulations. CFD calculations are also used to study the design and specification of new microreactor developments. The potential advantages of using a microreactor include better control of reaction conditions, improved safety and portability. A more detailed crude assay of the raw national oil, whose importance was evidenced by PETROBRAS/CENPES allows establishing the optimum strategies and processing conditions, aiming at a maximum utilization of the heavy oil fractions, towards valuable products. These residues are able to be processed in microreactor, in which conventional process like as hydrotreating, catalytic and thermal cracking may be carried out in a much more intensified fashion. The whole process development involves a prior thermal study to define the possible operating conditions for a particular task, the microreactor design through computational fluid dynamics and construction using rapid prototyping. This gives high flexibility for process development, shorter time, and costumer/task oriented process/product development. (author)

Catalytic copyrolysis of cork oak and bio-oil distillation residue

Science.gov (United States)

Lee, Yejin; Oh, Daejun; Kim, Young-Min; Jae, Jungho; Jung, Sang-Chul; Jeon, Jong-Ki; Kim, Sang Chai; Park, Young-Kwon

2018-01-01

The atmospheric distillation residue (ADR) of cork oak (CO) pyrolysis oil was used as the co-feeding material for the catalytic pyrolysis of CO over HZSM-5 catalysts to improve the formation of aromatic hydrocarbons. Although the non-catalytic copyrolysis of CO and ADR did not improve the formation of aromatic hydrocarbons, the catalytic copyrolysis of CO and ADR promoted the synergistic formation of aromatic hydrocarbons. HZSM-5(30), having a lower SiO2/Al2O3(30), showed better performance for the formation of aromatic hydrocarbons than HZSM-5(80) because of its higher acidity. The catalytic copyrolysis of CO and ADR also decreased the formation of coke. The largest quantity of aromatic hydrocarbons was obtained from the catalytic copyrolysis of CO and ADR over HZSM-5 (30) at 600 °C, whereas the lowest coke yield was achieved at 700 °C. When the catalyst to sample ratio was increased from 2:1 to 5:1, the synergistic formation of aromatic hydrocarbons was limited, resulting in a lower experimental yield of aromatic hydrocarbons than the theoretical yield. A lower coke yield was also achieved at a high catalyst to sample ratio (5:1).

Phylogenetic diversity of dominant bacterial communities during bioremediation of crude oil-polluted soil

Directory of Open Access Journals (Sweden)

Eugene Thomas Cloete

2011-08-01

Full Text Available Bioremediation of hydrocarbon pollutants is advantageous owing to the cost-effectiveness of the technology and the ubiquity of hydrocarbon degrading microorganisms in the soil. Soil microbial diversity is affected by hydrocarbon perturbation thus selective enrichment of hydrocarbon utilizers occurs. Hydrocarbons interact with the soil matrix and soil microorganisms determining the fate of the contaminants relative to their chemical nature and microbial degradative capabilities respectively. Bacterial dynamics in crude oil-polluted soil microcosms undergoing bioremediation were investigated over a 42-day period. Four out of the five microcosms containing 4kg of pristine soil each were contaminated with 4% Arabian light crude oil. Three microcosms were amended with either 25g of NPK fertilizer, calcium ammonium nitrate or poultry droppings respectively while the fourth designated oil-contaminated control was unamended. The fifth microcosm had only pristine soil and was set up to ascertain indigenous bacterial community structure pre-contamination. Biostimulated soils were periodically tilled and watered. Hydrocarbon degradation was measured throughout the experimental period by gas chromatography. Gas chromatographic tracing of residual hydrocarbons in biostimulated soils showed marked attenuation of contaminants starting from the second (day 14 till the sixth (day 42 week after contamination whereas no significant reduction in hydrocarbon peaks was seen in the oil contaminated control soil throughout the 6-week experimental period. Molecular fingerprints of bacterial communities involved in aerobic biodegradation of crude oil hydrocarbons in biostimulated soils and controls were generated with DGGE using PCR-amplification of 16S rRNA gene obtained from extracted total soil community DNA. DGGE fingerprints demonstrated that NPK, calcium ammonium nitrate and poultry droppings selected different bacterial populations during the active phase of oil

Onset of entrainment and degree of dispersion in dual continuous horizontal oil-water flows

Energy Technology Data Exchange (ETDEWEB)

Al-Wahaibi, Talal [Department of Petroleum and Chemical Engineering, Sultan Qaboos University, P.O. Box 33, Al-Khoud, P.C. 123 (Oman); Angeli, Panagiota [Department of Chemical Engineering, University College London, Torrington Place, London WC1E 7JE (United Kingdom)

2009-04-15

The transition from stratified to dual continuous oil-water flow (where each phase retains its continuity but there is dispersion of one phase into the other) as well as the dispersed phase fractions in the layers of the dual continuous pattern, were studied experimentally. Transition to this pattern from stratified flow occurs when drops of one phase appear into the other (onset of entrainment). The studies were carried out in a 38 mm ID horizontal stainless steel test section using two different inlet geometries, a T- and a Y-junction. The patterns were visualized through a transparent acrylic section located at 7 m from the inlet using a high speed video camera. Phase distribution measurements in a pipe cross section were obtained just before the acrylic section with a local impedance probe and the results were used to calculate the volume fraction of each phase entrained into the other. The onset of entrainment was found to occur at lower superficial water velocities as the oil superficial velocities increased. However, the inlet geometry did not affect significantly the transition line. During dual continuous flow, the dispersion of one phase into the opposite was found to extend further away from the interface with increasing water superficial velocity for a certain oil superficial velocity. An increase in the superficial water velocity increased the entrained fraction of water in oil (E{sub w/o}) but there was no trend with the oil velocity. Similarly, an increase in the superficial oil velocity increased the fraction of oil drops in water (E{sub o/w}) but the water velocity had no clear effect. The entrainment fractions were affected by the inlet geometry, with the T-inlet resulting in higher entrainment than the Y-inlet, perhaps because of the increased mixing induced by the T-inlet. The difference between the two inlets increased as the oil and water velocities increased. (author)

Microbial enhanced oil recovery and compositions therefor

Science.gov (United States)

Bryant, Rebecca S.

1990-01-01

A method is provided for microbial enhanced oil recovery, wherein a combination of microorganisms is empirically formulated based on survivability under reservoir conditions and oil recovery efficiency, such that injection of the microbial combination may be made, in the presence of essentially only nutrient solution, directly into an injection well of an oil bearing reservoir having oil present at waterflood residual oil saturation concentration. The microbial combination is capable of displacing residual oil from reservoir rock, which oil may be recovered by waterflooding without causing plugging of the reservoir rock. Further, the microorganisms are capable of being transported through the pores of the reservoir rock between said injection well and associated production wells, during waterflooding, which results in a larger area of the reservoir being covered by the oil-mobilizing microorganisms.

DEVELOPMENT OF BIOSURFACTANT-MEDIATED OIL RECOVERY IN MODEL POROUS SYSTEMS AND COMPUTER SIMULATIONS OF BIOSURFACTANT-MEDIATED OIL RECOVERY

Energy Technology Data Exchange (ETDEWEB)

M.J. McInerney; S.K. Maudgalya; R. Knapp; M. Folmsbee

2004-05-31

Current technology recovers only one-third to one-half of the oil that is originally present in an oil reservoir. Entrapment of petroleum hydrocarbons by capillary forces is a major factor that limits oil recovery (1, 3, 4). Hydrocarbon displacement can occur if interfacial tension (IFT) between the hydrocarbon and aqueous phases is reduced by several orders of magnitude. Microbially-produced biosurfactants may be an economical method to recover residual hydrocarbons since they are effective at low concentrations. Previously, we showed that substantial mobilization of residual hydrocarbon from a model porous system occurs at biosurfactant concentrations made naturally by B. mojavensis strain JF-1 if a polymer and 2,3-butanediol were present (2). In this report, we include data on oil recovery from Berea sandstone experiments along with our previous data from sand pack columns in order to relate biosurfactant concentration to the fraction of oil recovered. We also investigate the effect that the JF-2 biosurfactant has on interfacial tension (IFT). The presence of a co-surfactant, 2,3-butanediol, was shown to improve oil recoveries possibly by changing the optimal salinity concentration of the formulation. The JF-2 biosurfactant lowered IFT by nearly 2 orders of magnitude compared to typical values of 28-29 mN/m. Increasing the salinity increased the IFT with or without 2,3-butanediol present. The lowest interfacial tension observed was 0.1 mN/m. Tertiary oil recovery experiments showed that biosurfactant solutions with concentrations ranging from 10 to 60 mg/l in the presence of 0.1 mM 2,3-butanediol and 1 g/l of partially hydrolyzed polyacrylamide (PHPA) recovered 10-40% of the residual oil present in Berea sandstone cores. When PHPA was used alone, about 10% of the residual oil was recovered. Thus, about 10% of the residual oil recovered in these experiments was due to the increase in viscosity of the displacing fluid. Little or no oil was recovered at

Performance improvement of a drop-on-demand inkjet printhead using an optimization-based feedforward control method

NARCIS (Netherlands)

Khalate, A.; Bombois, X.; Babuska, R.; Wijshoff, H.M.A.; Waarsing, R.

2011-01-01

The printing quality delivered by a drop-on-demand (DoD) inkjet printhead is limited due to the residual oscillations in the ink channel. The maximal jetting frequency of a DoD inkjet printhead can be increased by quickly damping the residual oscillations and by bringing in this way the ink channel

Sulfur compounds and species in Russian residues by XPS and PY-GC-PFPO

Energy Technology Data Exchange (ETDEWEB)

Quan, S.; Suoqi, Z.; Chunming, X. [University of Petroleum, State Key Laboraory of Heavy Oil Processing, Beijing (China); Kotlyar, L.; Kung, J. [National Research Council of Canada, Institute for Chemical processand Environmental Technology, Ottawa, ON (Canada); Chung, K. H. [Syncrude Canada Limited, Edmonton, AB (Canada)

2004-07-01

Distribution and structure of sulfur components of Russian crude oil were investigated by separating vacuum residues from the oil into 17 narrow cuts and one end-cut using the supercritical fluid extraction and fractionation technique (SFEF). The cuts were analyzed by gas chromatography, with conditions optimized from 600 degrees C to 1,000 degrees C, and between two and twenty seconds. In general, the total amount of of the sulfur compounds in pyrolizates was found to be proportional to the sulfur content in the vacuum residues. Thiophenes, benzothiophenes and dibenzothiophene content varied from vacuum residue to vacuum residue. Benzothiophens were identified as the dominant sulfur compounds in the pyrolizate of Russian crude oil.

Drop evaporation and triple line dynamics

Science.gov (United States)

Sobac, Benjamin; Brutin, David; Gavillet, Jerome; Université de Provence Team; Cea Liten Team

2011-03-01

Sessile drop evaporation is a phenomenon commonly came across in nature or in industry with cooling, paintings or DNA mapping. However, the evaporation of a drop deposited on a substrate is not completely understood due to the complexity of the problem. Here we investigate, with several nano-coating of the substrate (PTFE, SiOx, SiOc and CF), the influence of the dynamic of the triple line on the evaporation process. The experiment consists in analyzing simultaneously the motion of the triple line, the kinetics of evaporation, the internal thermal motion and the heat and mass transfer. Measurements of temperature, heat-flux and visualizations with visible and infrared cameras are performed. The dynamics of the evaporative heat flux appears clearly different depending of the motion of the triple line

Semisupervised Community Detection by Voltage Drops

Directory of Open Access Journals (Sweden)

Min Ji

2016-01-01

Full Text Available Many applications show that semisupervised community detection is one of the important topics and has attracted considerable attention in the study of complex network. In this paper, based on notion of voltage drops and discrete potential theory, a simple and fast semisupervised community detection algorithm is proposed. The label propagation through discrete potential transmission is accomplished by using voltage drops. The complexity of the proposal is OV+E for the sparse network with V vertices and E edges. The obtained voltage value of a vertex can be reflected clearly in the relationship between the vertex and community. The experimental results on four real networks and three benchmarks indicate that the proposed algorithm is effective and flexible. Furthermore, this algorithm is easily applied to graph-based machine learning methods.

Natural radioactivity in petroleum residues

International Nuclear Information System (INIS)

Gazineu, M.H.P.; Gazineu, M.H.P.; Hazin, C.A.; Hazin, C.A.

2006-01-01

The oil extraction and production industry generates several types of solid and liquid wastes. Scales, sludge and water are typical residues that can be found in such facilities and that can be contaminated with Naturally Occurring Radioactive Material (N.O.R.M.). As a result of oil processing, the natural radionuclides can be concentrated in such residues, forming the so called Technologically Enhanced Naturally Occurring Radioactive Material, or T.E.N.O.R.M.. Most of the radionuclides that appear in oil and gas streams belong to the 238 U and 232 Th natural series, besides 40 K. The present work was developed to determine the radionuclide content of scales and sludge generated during oil extraction and production operations. Emphasis was given to the quantification of 226 Ra, 228 Ra and 40 K since these radionuclides,are responsible for most of the external exposure in such facilities. Samples were taken from the P.E.T.R.O.B.R.A.S. unity in the State of Sergipe, in Northeastern Brazil. They were collected directly from the inner surface of water pipes and storage tanks, or from barrels stored in the waste storage area of the E and P unit. The activity concentrations for 226 Ra, 228 Ra and 40 K were determined by using an HP Ge gamma spectrometric system. The results showed concentrations ranging from 42.7 to 2,110.0 kBq/kg for 226 Ra, 40.5 to 1,550.0 kBq/kg for 228 Ra, and 20.6 to 186.6 kBq/kg for 40 K. The results highlight the importance of determining the activity concentration of those radionuclides in oil residues before deciding whether they should be stored or discarded to the environment. (authors)

Effects of storage and processing on residue levels of chlorpyrifos in soybeans.

Science.gov (United States)

Zhao, Liuwei; Ge, Jing; Liu, Fengmao; Jiang, Naiwen

2014-05-01

The residue levels of chlorpyrifos in soybeans during storage and processing were investigated. Soybeans were treated with chlorpyrifos aqueous solution and placed in a sealed plastic container. The residue of chlorpyrifos was determined in soybeans at six time points within 0 and 112days during storage and oil processing of the soybeans was conducted. The analysis of the residues of chlorpyrifos was carried out by gas chromatography-mass spectrometry (GC-MS). Results show that the dissipation of chlorpyrifos in soybeans is about 62% during the storage period. Moreover, the carryover of the residues from soybeans into oil is found to be related to the processing methods. Processing factor, which is defined as the ratio of chlorpyrifos residue concentration in oil sample to that in the soybean samples, was 11 and 0.25 after cold and hot pressing, respectively. Copyright © 2013 Elsevier Ltd. All rights reserved.

Falling R and D in oil companies

International Nuclear Information System (INIS)

Creusen, H.; Minne, B.

2000-01-01

During the last decade, the research expenditures of the 11 major oil companies and two specialised oil engineers have dropped worldwide. To explain this trend, this article points to an R and D race among the companies and to certain common expectations. The race is due to the absence of knowledge spillovers across the companies, because they need to keep their process innovations secret. Common expectations regarding the high risks of research for new energy sources leads to wait-and-see behaviour instead of own research. A small increase in research efficiency partly compensates for the drop in R and D

Partial least squares modeling of combined infrared, 1H NMR and 13C NMR spectra to predict long residue properties of crude oils

NARCIS (Netherlands)

de Peinder, P.; Visser, T.; Petrauskas, D.D.; Salvatori, F.; Soulimani, F.; Weckhuysen, B.M.

2009-01-01

Research has been carried out to determine the potential of partial least squares (PLS) modeling of mid-infrared (IR) spectra of crude oils combined with the corresponding 1H and 13C nuclear magnetic resonance (NMR) data, to predict the long residue (LR) properties of these substances. The study

Metagenome enrichment approach used for selection of oil-degrading bacteria consortia for drill cutting residue bioremediation.

Science.gov (United States)

Guerra, Alaine B; Oliveira, Jorge S; Silva-Portela, Rita C B; Araújo, Wydemberg; Carlos, Aline C; Vasconcelos, Ana Tereza R; Freitas, Ana Teresa; Domingos, Yldeney Silva; de Farias, Mirna Ferreira; Fernandes, Glauber José Turolla; Agnez-Lima, Lucymara F

2018-04-01

Drill cuttings leave behind thousands of tons of residues without adequate treatment, generating a large environmental liability. Therefore knowledge about the microbial community of drilling residue may be useful for developing bioremediation strategies. In this work, samples of drilling residue were enriched in different culture media in the presence of petroleum, aiming to select potentially oil-degrading bacteria and biosurfactant producers. Total DNA was extracted directly from the drill cutting samples and from two enriched consortia and sequenced using the Ion Torrent platform. Taxonomic analysis revealed the predominance of Proteobacteria in the metagenome from the drill cuttings, while Firmicutes was enriched in consortia samples. Functional analysis using the Biosurfactants and Biodegradation Database (BioSurfDB) revealed a similar pattern among the three samples regarding hydrocarbon degradation and biosurfactants production pathways. However, some statistical differences were observed between samples. Namely, the pathways related to the degradation of fatty acids, chloroalkanes, and chloroalkanes were enriched in consortia samples. The degradation colorimetric assay using dichlorophenolindophenol as an indicator was positive for several hydrocarbon substrates. The consortia were also able to produce biosurfactants, with biosynthesis of iturin, lichnysin, and surfactin among the more abundant pathways. A microcosms assay followed by gas chromatography analysis showed the efficacy of the consortia in degrading alkanes, as we observed a reduction of around 66% and 30% for each consortium in total alkanes. These data suggest the potential use of these consortia in the bioremediation of drilling residue based on autochthonous bioaugmentation. Copyright © 2018 Elsevier Ltd. All rights reserved.

The Resurgence of Shale Oil

International Nuclear Information System (INIS)

Cornot-Gandolphe, Sylvie

2017-09-01

This study addresses the resilience factors of the American production of light tight oil, in particular regarding the evolution of the financial model, and the regulatory changes with the authorisation of exports for crude oil. The paper also evaluates the development perspectives of the production on the medium and long term. US production of light tight oil (LTO, commonly known as 'shale oil') experienced a spectacular expansion between 2010 and 2014, becoming the largest source of growth in world oil production. At the start of 2015, however, the sustainability of its business model became questionable. Oil prices had collapsed and uncertainty about future US production was at its height. The sharp drop in the number of drill holes as of January 2015 raised fears of a rapid fall in US petroleum output. The LTO business model, based largely on the use of debt, reinforced this projection. Independent producers were heavily indebted, and were no longer able to invest in new wells. LTO production would therefore run out of steam. Two years later, LTO has passed its first test successfully. While output of shale gas has clearly fallen, cuts have been modest and much less than had been feared, given the falls in capital spending (CAPEX) and the number of drill holes. Productivity improvements as well as cost reductions have permitted a halving of the LTO equilibrium price. Independent producers have refocused their activities on the most productive basins and sites. The essential role played by the Permian Basin should be stressed at this point. In two years, it has become a new El dorado. Despite the fall in drill holes through to May 2016, production has continued to rise and now amounts to a quarter of American oil output. Furthermore, independents have drawn extra value from their well inventories, which include drilled, but also uncompleted wells. Lastly, the impressive number of drilled wells prior to price cuts has allowed producers to maintain their output

Fifth DOE symposium on enhanced oil and gas recovery and improved drilling technology. Volume 2. Oil

Energy Technology Data Exchange (ETDEWEB)

Linville, B. [ed.

1979-01-01

Volume 2 contains papers from the following sessions: residual oil determination; thermal methods; heavy oil-tar sands; technology transfer; and carbon dioxide flooding. Individual papers were processed.

Super oil cracking update

International Nuclear Information System (INIS)

Mulraney, D.

1997-01-01

The conversion of residual fuel oil to usable middle distillates was discussed. The residue conversion processing paths are usually based on separation, carbon rejection, or hydrogen addition principles. Super Oil Cracking (SOC) uses a slurry catalyst system in a new, tubular reactor to achieve high levels of hydrothermal conversion. SOC can upgrade a variety of heavy, high metals residue feedstocks with high yields of middle distillates. The SOC products can also be further treated into feedstocks for FCC or hydrocracking. The SOC process can be incorporated easily into a refinery to obtain incremental residue conversion directly. It can also be integrated with other residue processes, acting as a demetallization and decarbonization step which results in enhanced overall conversion. The relative rate of coke formation and its handling are distinguishing characteristics between residue upgrading technologies. The SOC process operates at higher temperatures that other residue hydrocracking processes resulting in higher rates of thermal decomposition, thus preventing coke formation. SOC process can operate as a stand-alone upgrader or can be integrated with other bottoms processing steps to extend the refiner's range of options for increasing bottoms conversion.3 tabs., 14 figs

Charred olive stones: experimental and archaeological evidence for recognizing olive processing residues used as fuel

NARCIS (Netherlands)

Braadbaart, Freek; Marinova, E.; Sarpaki, A.

After extracting oil from olives a residue is left usually referred to as the olive oil processing residue (OPR). This study explores the way in which ancient societies may have used OPR as fuel for fires to generate heat and the various issues that are related to the residues of this fuel. After

Characterization of hams added with nut residual pastes from the mechanical extraction of oil

Directory of Open Access Journals (Sweden)

Juan José Luna Guevara

2013-06-01

Full Text Available Nuts contain in their composition nutrients and bioactive compounds that when consumed in sufficient amounts may provide health benefits. In this study was evaluated the influence of the addition of residual pastes (10%, obtained from the extraction of oil from walnut (Juglans regia L., pecan (Carya illinoinensis (Wangenh. K. Koch, variety Western Shley, and peanut (Arachis hypogaea, on the modification of some textural, proximate, physicochemical, microbiological and sensory characteristics of cooked hams. Hams were stored at 4 ° C for 21 days. Hams containing pastes significantly increased (P ≤ 0.05 the protein, fat, and total fiber content. Hams added with paste presented a less rigid structures (P ≤ 0.05. The color parameters (L*, a*, and b* of hams decrease slightly during the storage time, except for the ham added with walnut paste, which was darker. The nut pastes contributed significantly (P ≤ 0.05 to decrease the shelf life of hams. However, the yeast and mold counts in ham were less than 10 CFU/g at 21 days of storage. aw and pH decreased significantly (P ≤ 0.05 and syneresis increased during storage. Hams added with residual pastes were well sensory accepted regarding color, aroma, taste, appearance, and overall acceptability.

Economics of Russian oil production

International Nuclear Information System (INIS)

Gubenko, I.

1993-01-01

The main technical indicators of oil production in Russia are presented from the year 1988, when the current decline in oil production started. In 1992, only 9 new oil deposits were put into production, and average well productivity dropped to 12.4 tonnes/d. The number of idle wells reached 31,934 as compared to 8,714 in 1988. The share of low productivity deposits in 1993 was 49.7%. In the first five months of 1993, the number of new wells put into operation failed to offset the shutdown of old wells. Although the number of workovers grew by 32%, this work was insufficient to stabilize oil production. The decline in production is due to the general state of economic stability and endless reorganizations in the economy, and to the lack of sufficient investment in the industry. Oil-producing enterprises have lacked funds due to systematic and growing indebtedness of buyers of crude. This overdue indebtedness reached 393 billion rubles by the beginning of 1993. Although domestic oil prices increased sharply in 1991-92, the volume of production in real terms has dropped by nearly a third. Oil is sold at different prices to different categories of buyers. Prices include expenses, profit from which a 32% profits tax is paid, excise taxes, and payments to a centralized price-regulation fund. From the industry point of view, certain reforms are necessary to reconstruct and develop the industry. These include ensuring payments to oil producers, gradual transfer of Russian prices to world levels, lowering taxes, and adoption and refinement of a law on oil. 1 fig., 7 tabs

Prediction of long-residue properties of potential blends from mathematically mixed infrared spectra of pure crude oils by partial least-squares regression models

NARCIS (Netherlands)

de Peinder, P.; Visser, T.; Petrauskas, D.D.; Salvatori, F.; Soulimani, F.; Weckhuysen, B.M.

2009-01-01

Research has been carried out to determine the feasibility of partial least-squares (PLS) regression models to predict the long-residue (LR) properties of potential blends from infrared (IR) spectra that have been created by linearly co-adding the IR spectra of crude oils. The study is the follow-up

Anaerobic digestion of residues from production and refining of vegetable oils as an alternative to conventional solutions.

Science.gov (United States)

Torrijos, M; Thalla, Arun Kumar; Sousbie, P; Bosque, F; Delgenès, J P

2008-01-01

The purpose of this work was to study the anaerobic digestion of by-products generated during the production and refining of oil with the objective of proposing an alternative solution (methanisation) to the conventional solutions while reducing the energy consumption of fossil origin on refinery sites. The production of sunflower oil was taken as example. Glycerine from the production of biodiesel was also included in this study. The results show that glycerine has a high potential for methanisation because of its high methane potential (465 ml CH4/g VS) and high metabolization rates (0.42 g VS/g VSS.d). The use of oil cake as substrate for anaerobic digestion is not interesting because it has a low methane potential of 215 ml CH4/g VS only and because it is easily recovered in animal feed. Six residues have quite a high methane potential (465 to 850 ml CH4/g VS) indicating a good potential for anaerobic digestion. However, they contain a mixture of rapidly and slowly biodegradable organic matter and the loading rates must remain quite low (0.03 to 0.09 g VS/g VSS.d) to prevent any accumulation of slowly biodegradable solids in the digesters. IWA Publishing 2008.

Optimization-based feedforward control for a drop-on-demand inkjet printer

NARCIS (Netherlands)

Khalate, A.; Bombois, X.; Babuska, R.; Wijshoff, H.M.A.; Waarsing, R.

2010-01-01

The printing quality delivered by a Drop-on-Demand (DoD) inkjet printhead is limited due to operational issues such as residual oscillations in the ink channel and the cross-talk between the ink channels. The maximal jetting frequency of a DoD inkjet printhead can be increased by quickly damping the

Mechanisms of microbial oil recovery by Clostridium acetobutylicum and Bacillus strain JF-2

Energy Technology Data Exchange (ETDEWEB)

Marsh, T.L.; Zhang, X.; Knapp, R.M.; McInerney, M.J.; Sharma, P.K.; Jackson, B.E.

1995-12-31

Core displacement experiments at elevated pressures were conducted to determine whether microbial processes are effective under conditions that simulate those found in an actual oil reservoir. The in-situ growth of Clostridium acetobutylicum and Bacillus strain JF-2 resulted in the recovery of residual oil. About 21 and 23% of the residual oil was recovered by C. acetobutylicum and Bacillus strain JF-2, respectively. Flooding cores with cell-free culture fluids of C. acetobutylicum with and without the addition of 50 mM acetone and 100 mM butanol did not result in the recovery of residual oil. Mathematical simulations showed that the amount of gas produced by the clostridial fermentation was not showed that the amount of gas produced by the clostridial fermentation was not sufficient to recover residual oil. Oil recovery by Bacillus strain JF-2 was highly correlated to surfactant production. A biosurfactant-deficient mutant of strain JF-2 was not capable of recovering residual oil. These data show that surfactant production is an important mechanism for microbially enhanced oil recovery. The mechanism for oil recovery by C. acetobutylicum is not understood at this time, but the production of acids, solvents, or gases alone cannot explain the observed increases in oil recovery by this organism.

A Study of the Use of Jatropha Oil Blends in Boilers

Energy Technology Data Exchange (ETDEWEB)

Krishna, C.R.

2010-10-01

Executive Summary: This project investigated the combustion performance of blends of unrefined Jatropha oil and its blends in laboratory boilers. Although a very limited amount of testing blends in distillate oil, ASTM No. 2 oil or heating oil was conducted, the primary interest was in testing the performance of blends with residual ASTM No. 6 oil. The basic idea is to provide a renewable fuel option to residual oil used in space heating and in industrial applications. The intent also was to explore the use of non-edible plant oil and one that might be potentially cheaper than biodiesel. The characteristics of No. 6 oil, such as high viscosity at ambient temperature, which requires it to be kept heated, make the blending with such oils feasible. Jatropha oil is one such oil and there is currently considerable interest building up in its use as a source for making biodiesel and jet fuel. A 10% blend of Jatropha oil with heating oil was burned using a standard burner in a residential boiler. Combustion performance was shown to be comparable with that of burning heating oil by itself with some noticeable differences. Typical heating oil has about 2000 ppm of sulfur, while the Jatropha oil has about 50 ppm leading to lower levels of sulphur dioxide emissions. Stack measurements also showed that the NOx emission was lower with the blend. We have previously reported similar reductions in NOx with blends of biodiesel in heating oil as well as slight reductions in PM2.5, particulates below 2.5 microns in size. Long term tests were not part of this project and hence deleterious effects on pumps, seals etc., if any, were not measured. The majority of the work involved testing blends of Jatropha oil with residual oil in a 1.5 million Btu/hr boiler with a burner modified to burn residual oil. Blends of 20 and 60% Jatropha oil and 100% Jatropha oil were burned in the combustion performance tests. The residual oil used had a sulfur content of over 2000 ppm and hence dramatic

A New Era of Oil Abundance?

International Nuclear Information System (INIS)

Aoun, Marie-Claire

2015-01-01

From 2014 to 2015, the price of oil fell. The price drop is explained by several factors: a significant increase of oil production in the United States, the resumption of Libyan and Iraqi exports, the possible lifting of sanctions against Iran, and slowing growth in developing countries. The situation is having negative effects on oil-producing countries, but the Organization of the Petroleum Exporting Countries (OPEC) remains divided as to its stance on the situation, making it all the more difficult to predict future trends in oil prices

In situ exposure of herring embryos in Prince William Sound two years after the Exxon Valdez oil spill

International Nuclear Information System (INIS)

Kocan, R.; Brown, E.; Baker, T.

1995-01-01

In order to evaluate long-term residual toxicity, artificially spawned Pacific herring (Clupea pallasl) embryos were deployed at 5 oiled and 5 unoiled sites in Prince William Sound two years after the Exxon Valdez oil spill. Embryos were exposed at 1.5 m and 4.5 m below mean low water for 8--10 d post fertilization. The embryos were then retrieved and transported to the laboratory for hatching and evaluation under controlled conditions, Endpoints were (1) embryo survival, (2) live hatch, (3) deformed larvae and (4) larval dry weight. The oiled sites produced significantly (P < 0.01) more deformed larvae (63.3%) than did the unoiled sites (51.3%), but there was a lower hatching success at the unoiled sites which resulted in no overall difference in normal live larvae produced between oiled and unoiled sites. The mean dry weight of newly hatched larvae from the oiled sites (78 microg/larva) was significantly lower than those from the unoiled sites (97 microg/larva) at all depths (P < 0.01). Increased larval deformities and reduced hatching weight is consistent with what has been reported by several investigators for herring larvae experimentally and naturally exposed to petroleum hydrocarbons. Based on the data, there appeared to be differences between the previously oiled and unoiled sites relative to herring development, but it is not clear whether this was due to residual oil effects or parental effects

Capillary-Physics Mechanism of Elastic-Wave Mobilization of Residual Oil

Science.gov (United States)

Beresnev, I. A.; Pennington, W. D.; Turpening, R. M.

2003-12-01

Much attention has been given to the possibility of vibratory mobilization of residual oil as a method of enhanced recovery. The common features of the relevant applications have nonetheless been inconsistency in the results of field tests and the lack of understanding of a physical mechanism that would explain variable experiences. Such a mechanism can be found in the physics of capillary trapping of oil ganglia, driven through the pore channels by an external pressure gradient. Entrapping of ganglia occurs due to the capillary pressure building on the downstream meniscus entering a narrow pore throat. The resulting internal-pressure imbalance acts against the external gradient, which needs to exceed a certain threshold to carry the ganglion through. The ganglion flow thus exhibits the properties of the Bingham (yield-stress) flow, not the Darcy flow. The application of vibrations is equivalent to the addition of an oscillatory forcing to the constant gradient. When this extra forcing acts along the gradient, an instant "unplugging" occurs, while, when the vibration reverses direction, the flow is plugged. This asymmetry results in an average non-zero flow over one period of vibration, which explains the mobilization effect. The minimum-amplitude and maximum-frequency thresholds apply for the mobilization to occur. When the vibration amplitude exceeds a certain "saturation" level, the flow returns to the Darcy regime. The criterion of the mobilization of a particular ganglion involves the parameters of both the medium (pore geometry, interfacial and wetting properties, fluid viscosity) and the oscillatory field (amplitude and frequency). The medium parameters vary widely under natural conditions. It follows that an elastic wave with a given amplitude and frequency will always produce a certain mobilization effect, mobilizing some ganglia and leaving others intact. The exact macroscopic effect is hard to predict, as it will represent a response of the populations

Sassafras oil overdose

Science.gov (United States)

Sassafras oil comes from the root bark of the sassafras tree. Sassafras oil overdose occurs when someone swallows more than the ... Safrole is the poisonous ingredient in sassafras oil. It is a clear or ... yellow oily liquid. It can be dangerous in large amounts.

Clay-oil flocculation and its role in natural cleansing in Prince William Sound following the Exxon Valdez oil spill

International Nuclear Information System (INIS)

Bragg, J.R.; Yang, S.H.

1995-01-01

Natural interactions of fine mineral particles with residue oil and seawater, in a process called clay-oil flocculation, were found to create solids-stabilized oil-in-water emulsions on shoreline sediments at numerous locations in Prince William Sound following the Exxon Valdez spill. In laboratory tests using oiled sediment samples from Prince William Sound, these emulsions were shown to facilitate natural cleansing and dispersion of oil from sediments by moving water. To investigate the effect of flocculation on natural cleansing, studies were conducted to determine the hydrodynamic energy needed for seawater to remove flocculated oil residues from sediments sampled from shorelines. Water was pumped at different velocities through a column packed with oiled sediment, and the amount and composition of oil removed from the sediment were measured as functions of water velocity and sediment movement. In separate tests, oil removal was observed in a wave tank that generated wave heights less than and greater than needed to move sediments. 28 refs., 13 figs., 7 tabs

Preparation of cement from oil shale

Energy Technology Data Exchange (ETDEWEB)

1922-08-24

A process for preparing cement from oil shale is described. The simultaneous recovery of shale oil by heating the oil shale formed into briquets with finely ground lime or limestone in a stream of hot gases is characterized by the fact that live steam or fine drops of water as preserving and carbonization means is introduced into the furnace, at the place, where the temperature of the briquet reaches about 500 to 600/sup 0/ C.

Characterization of Paraiba state, Brazil, clays used for clearing of oil of frying for application as bio fuel; Cacterizacao de argilas do estado da Paraiba, Brasil, utilizaadas para clareamento de oleos de fritura usados para aplicacao como biobombustivel

Energy Technology Data Exchange (ETDEWEB)

Araujo, E.P.; Oliveira, S.V. de; Medeiros, K.M. de; Araujo, E.M.; Fook, M.V.L. [Universidade Federal de Campina Grande (DEMa/UFCG), PB (Brazil). Dept. de Engenharia de Materiais], e-mail: elainepatriciaaraujo@yahoo.com.br

2008-07-01

The search for new sources of renewable energy order to minimize environmental impacts has led the scientists to develop new alternatives, such as the use of recycling of frying oils to produce biodiesel. The reuse of these oils has the advantage of obtaining a biofuel with the cost / benefit competitive. However, the conditions of post-consumer oils require treatment prior to its conversion the chemical (transesterification), removing solid particulate contaminants and adjusting its color using the clay of Paraiba. The use of biodiesel as fuel presents a reduction of levels of environmental pollution. This study aimed to characterize clay of Paraiba to be used in the clearing of frying oil. It was observed through the results of the Xray fluorescence (XRF) and infrared spectroscopy by Fourier Transform (FTIR), which the clays tested, have been effective in clearing of frying oils, making them similar to oil 'virgin'. (author)

Drop jumping. II. The influence of dropping height on the biomechanics of drop jumping

NARCIS (Netherlands)

Bobbert, M F; Huijing, P A; van Ingen Schenau, G J

In the literature, athletes preparing for explosive activities are recommended to include drop jumping in their training programs. For the execution of drop jumps, different techniques and different dropping heights can be used. This study was designed to investigate for the performance of bounce

Residual Effect of Chemical and Animal Fertilizers and Compost on Yield, YieldComponents, Physiological Characteristics and Essential Oil Content of Matricaria chamomilla L. under Drought Stress conditions

Directory of Open Access Journals (Sweden)

a Ahmadian

2011-02-01

Full Text Available Abstract The residual effect of inorganic and organic fertilizers on growth and yield of plants is one of the important problems in nutrition. This study was conducted to determine the residual effect of different fertilizers on yield, yield components, physiological parameters and essential oil percentage of Matricaria chamomilla under drought stress. A split plot arrangement based on randomized completely block design (RCBD with three replication was conducted in 2009, at the University of Zabol. Treatments included W1 (non stress, W2 (75% FC and W3 (50% FC as main plot and three types of residual’s fertilizers: F1 (non fertilizer, F2 (chemical fertilizer, F3 (manure fertilizer and F4 (compost as sub plot. Results showed that water stress at W3 treatment reduced dry flower yield. Low water stress increased essential oil percentage and the highest oil was obtained in W2. In this experiment, free proline and total soluble carbohydrate concentration were increased under water stress. The residual’s manure and compost enhanced flower yield, percentage and yield of essential oil of chamomile at the second year. At a glance, animal manure application and light water stress (75% FC was recommended to obtain best quantitative and qualitative yield. Keywords: Water Stress, Fertilizer, Carbohydrate, Proline, Chamomile

First drop dissimilarity in drop-on-demand inkjet devices

International Nuclear Information System (INIS)

Famili, Amin; Palkar, Saurabh A.; Baldy, William J. Jr.

2011-01-01

As inkjet printing technology is increasingly applied in a broader array of applications, careful characterization of its method of use is critical due to its inherent sensitivity. A common operational mode in inkjet technology known as drop-on-demand ejection is used as a way to deliver a controlled quantity of material to a precise location on a target. This method of operation allows ejection of individual or a sequence (burst) of drops based on a timed trigger event. This work presents an examination of sequences of drops as they are ejected, indicating a number of phenomena that must be considered when designing a drop-on-demand inkjet system. These phenomena appear to be driven by differences between the first ejected drop in a burst and those that follow it and result in a break-down of the linear relationship expected between driving amplitude and drop mass. This first drop, as quantified by high-speed videography and subsequent image analysis, can be different in morphology, trajectory, velocity, and volume from subsequent drops within a burst. These findings were confirmed orthogonally by both volume and mass measurement techniques which allowed quantitation down to single drops.

The Effect of the Operating Conditions on the Apparent Viscosity of Crude Palm Oil During Oil Clarification

OpenAIRE

Sulaiman Al-Zuhair, Mirghani I. Ahmed and Yousif A. Abakr

2012-01-01

This paper discusses the apparent viscosity of crude palm oil, using rotary viscometer, under different boundary conditions. It was experimentally shown that the apparent viscosity of palm oil drops with increasing of the shear rate and the temperature.  However, the effect of temperature on the viscosity tends to fade at temperatures beyond 80 oC.  A correlation between the apparent viscosity of crude palm oil and the operating conditions was developed. This correlation can be used...

Unilever food safety assurance system for refined vegetable oils and fats

Directory of Open Access Journals (Sweden)

van Duijn Gerrit

2010-03-01

Full Text Available The Unilever Food Safety Assurance system for refined oils and fats is based on risk assessments for the presence of contaminants or pesticide residues in crude oils, and refining process studies to validate the removal of these components. Crude oil risk assessments were carried out by combining supply chain visits, and analyses of the contaminant and pesticide residue levels in a large number of crude oil samples. Contaminants like poly-aromatic hydrocarbons and hydrocarbons of mineral origin, and pesticide residues can largely be removed by refining. For many years, this Food Safety Assurance System has proven to be effective in controlling contaminant levels in refined vegetable oils and fats.

Foamed emulsion drainage: flow and trapping of drops

OpenAIRE

Schneider, Maxime; Zou, Ziqiang; Langevin, Dominique; Salonen, Anniina

2017-01-01

Foamed emulsions are ubiquitous in our daily life but the ageing of such systems is still poorly understood. In this study we investigate foam drainage and measure the evolution of the gas, liquid and oil volume fractions inside the foam. We evidence three regimes of ageing. During an initial period of fast drainage, both bubbles and drops are very mobile. As the foam stabilises drainage proceeds leading to a gradual decrease of the liquid fraction and slowing down of drainage. Clusters of oi...

Operational Performance of Offshore De-oiling Hydrocyclone Systems

DEFF Research Database (Denmark)

Løhndorf, Petar Durdevic; Pedersen, Simon; Yang, Zhenyu

2017-01-01

Maturing Oil & Gas reservoirs in the North Sea result in constant increases of water-cut, which correspondingly poses an increasing strain on the current offshore Produced Water Treatment (PWT) facilities. As one of the key elements of the PWT facilities, the hydrocyclone systems, are responsible...... for removing the remaining hydrocarbon content in the produced water before the treated water can be discharged, disposed, or reused as injection water. The hydrocyclone's performance heavily correlates with a number of system's and operational parameters, as well as dedicated control strategies. However......, these correlations haven't yet been clearly explored from a control oriented point of view, due to the complex separation dynamics inside the cyclone systems. This work investigates and evaluates the hydrocyclone system's operational performance with respect to the most commonly used control paradigm, Pressure Drop...

Flow Visualization in Evaporating Liquid Drops and Measurement of Dynamic Contact Angles and Spreading Rate

Science.gov (United States)

Zhang, Neng-Li; Chao, David F.

2001-01-01

A new hybrid optical system, consisting of reflection-refracted shadowgraphy and top-view photography, is used to visualize flow phenomena and simultaneously measure the spreading and instant dynamic contact angle in a volatile-liquid drop on a nontransparent substrate. Thermocapillary convection in the drop, induced by evaporation, and the drop real-time profile data are synchronously recorded by video recording systems. Experimental results obtained from this unique technique clearly reveal that thermocapillary convection strongly affects the spreading process and the characteristics of dynamic contact angle of the drop. Comprehensive information of a sessile drop, including the local contact angle along the periphery, the instability of the three-phase contact line, and the deformation of the drop shape is obtained and analyzed.

Sequential enrichment of microbial population exhibiting enhanced biodegradation of crude oil

International Nuclear Information System (INIS)

Venkateswaran, Kasthuri; Harayama, Shigeaki.

1995-01-01

The distribution of oil-degrading bacteria in the coastal waters and sediments of Hokkaido, Japan, was surveyed. It was found that the potential of mixed microbial populations to degrade weathered crude oil was not confined to any ecological components (water or sediment) nor to the sampling stations. One microbial culture that was stable during repeated subculturing degraded 45% of the saturates and 20% of the aromatics present in crude oil in 10 days during the initial screening. The residual hydrocarbons in this culture were extracted by chloroform and dispersed in a fresh seawater-based medium and subsequently inoculated with microorganisms from the first culture. After full growth of the second culture, the residual hydrocarbons were extracted and dispersed in a fresh medium in which microorganisms from the second culture had been inoculated. This sequential process was carried out six times to enrich those microorganisms that grew on the recalcitrant components of crude oil. After repeated exposure of the residual crude oil to the enriched microorganisms, about 80% of the initially added crude oil was degraded. The cultures obtained after each enrichment cycle were kept, and the degradation of fresh crude oil by the enriched microorganisms was monitored. The degrading activity of the enriched cultures increased as the number of enrichment cycles increased. A microbial population that had been selected six times on the residual crude oil could degrade 70% of the saturates and 30% of the aromatics of crude oil, indicating that growth of a microbial population on residual crude oil improved its ability to biodegrade crude oil. 21 refs., 2 tabs., 7 figs

Utilization of oil palm biodiesel solid residue as renewable sources for preparation of granular activated carbon by microwave induced KOH activation.

Science.gov (United States)

Foo, K Y; Hameed, B H

2013-02-01

In this work, preparation of granular activated carbon from oil palm biodiesel solid residue, oil palm shell (PSAC) by microwave assisted KOH activation has been attempted. The physical and chemical properties of PSAC were characterized using scanning electron microscopy, volumetric adsorption analyzer and elemental analysis. The adsorption behavior was examined by performing batch adsorption experiments using methylene blue as dye model compound. Equilibrium data were simulated using the Langmuir, Freundlich and Temkin isotherm models. Kinetic modeling was fitted to the pseudo-first-order, pseudo-second-order and Elovich kinetic models, while the adsorption mechanism was determined using the intraparticle diffusion and Boyd equations. The result was satisfactory fitted to the Langmuir isotherm model with a monolayer adsorption capacity of 343.94mg/g at 30°C. The findings support the potential of oil palm shell for preparation of high surface area activated carbon by microwave assisted KOH activation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Quarterly oil statistics. Second quarter, 1978

Energy Technology Data Exchange (ETDEWEB)

1978-01-01

This issue presents rapid and accurate information on supply and disposal of crude oil, oil products, and natural gas, including production, refinery output, trade, bunkers, refinery fuel and losses and stock changes. Detailed import and export data are given for 42 origins and 29 destinations for crude oil and products. NGL, feedstocks, naphtha, LPG, gasoline, kerosene, gas/diesel oil, and heavy fuel oil (residual) are covered. (DLC)

The oil companies in 1998

International Nuclear Information System (INIS)

Cueille, J.Ph.

1999-01-01

The drop in the price of crude oil has had a strong impact on oil companies earnings in 1998: for the first three-quarters, profits were down by an average 30 %. The performance levels attained by the refining-distribution activities, generally on a upwards trend, were not able to compensate for the sharp decrease in upstream earnings. Given these unfavorable circumstances, a number of companies are cutting back on capital investment projects. Unable to make further internal cost reductions on the same scale as before, oil companies are seeking to realize productivity gains through regional partnerships or large-scale mergers that, to some extent, could modify the traditional oil industry ranking

Effect of conducting core on the dynamics of a compound drop in an AC electric field

Science.gov (United States)

Soni, Purushottam; Dixit, Divya; Juvekar, Vinay A.

2017-11-01

Dynamics of 0.1M NaCl/castor oil/silicone oil compound drop in an alternating electric field of frequency 1 Hz was investigated experimentally in a parallel plate electrode cell. A novel yet simple method was used for producing the compound drop with different ratios of the core radius to shell radius. Deformation dynamics under both transient and cyclical steady states were recorded using high-speed imaging. We observed that with an increase in the radius ratio, deformation of the shell increases and that of the core decreases. The temporal deformation of the core always leads that of the shell. The phase lead between the core and the shell is independent of electric field strength and salt concentration in the core but strongly depends on the viscosity of the medium and radius ratio. At a small radius ratio, the breakup of the core is similar to the disintegration of the isolated drop in an infinite fluid; whereas the core attends a diamond-like shape at a high radius ratio before ejecting the small droplets from the tips.

Stretching the last drop of crude oil: a need for optimization of global production and consumption of oil

Energy Technology Data Exchange (ETDEWEB)

Shah, D. O.

1980-03-15

A blueprint is offered for the optimum production and consumption of oil, including desired changes in the Government energy policy, R and D planning, management philosophy, and attitude of people towards energy and material resources. Enhanced oil recovery from reservoirs is mentioned. (DLC)

The Effect of the Operating Conditions on the Apparent Viscosity of Crude Palm Oil During Oil Clarification

Directory of Open Access Journals (Sweden)

Sulaiman Al-Zuhair, Mirghani I. Ahmed and Yousif A. Abakr

2012-10-01

Full Text Available This paper discusses the apparent viscosity of crude palm oil, using rotary viscometer, under different boundary conditions. It was experimentally shown that the apparent viscosity of palm oil drops with increasing of the shear rate and the temperature.  However, the effect of temperature on the viscosity tends to fade at temperatures beyond 80 oC.  A correlation between the apparent viscosity of crude palm oil and the operating conditions was developed. This correlation can be used in design of crude palm oil settlers and in determining the optimum operating conditions.Key Words:  Crude palm oil, apparent viscosity, shear rate, modelling, separation 

Rheological behavior of water-in-oil emulsions stabilized by hydrophobic bentonite particles.

Science.gov (United States)

Binks, Bernard P; Clint, John H; Whitby, Catherine P

2005-06-07

A study of the rheological behavior of water-in-oil emulsions stabilized by hydrophobic bentonite particles is described. Concentrated emulsions were prepared and diluted at constant particle concentration to investigate the effect of drop volume fraction on the viscosity and viscoelastic response of the emulsions. The influence of the structure of the hydrophobic clay particles in the oil has also been studied by using oils in which the clay swells to very different extents. Emulsions prepared from isopropyl myristate, in which the particles do not swell, are increasingly flocculated as the drop volume fraction increases and the viscosity of the emulsions increases accordingly. The concentrated emulsions are viscoelastic and the elastic storage and viscous loss moduli also increase with increasing drop volume fraction. Emulsions prepared from toluene, in which the clay particles swell to form tactoids, are highly structured due to the formation of an integrated network of clay tactoids and drops, and the moduli of the emulsions are significantly larger than those of the emulsions prepared from isopropyl myristate.

Comparative study of biodegradation of crude oil in soil amended ...

African Journals Online (AJOL)

Analysis of soil samples treated with 10% (v/w) Escravos light crude oil and amended with chicken droppings and NPK fertilizer revealed that the aerobic heterotrophic bacterial counts were depressed while the proliferation of crude oil degrading bacteria (CDB) in the soil was encouraged. The counts of CDB in oil free ...

Antioxidant, Anti-Tyrosinase and Anti-Inflammatory Activities of Oil Production Residues from Camellia tenuifloria

Directory of Open Access Journals (Sweden)

Shu-Yuan Chiou

2015-12-01

Full Text Available Camellia tenuifloria is an indigenous Camellia species used for the production of camellia oil in Taiwan. This study investigated for the first time the potential antioxidant, anti-tyrosinase and anti-inflammatory activities of oil production byproducts, specifically those of the fruit shell, seed shell, and seed pomace from C. tenuifloria. It was found that the crude ethanol extract of the seed shell had the strongest DPPH scavenging and mushroom tyrosinase inhibitory activities, followed by the fruit shell, while seed pomace was the weakest. The IC50 values of crude extracts and fractions on monophenolase were smaller than diphenolase. The phenolic-rich methanol fraction of seed shell (SM reduced nitric oxide (NO production, and inducible nitric oxide synthase (iNOS expression in lipopolysaccharide (LPS-stimulated RAW 264.7 cells. It also repressed the expression of IL-1β, and secretion of prostaglandin E2 (PGE2 and IL-6 in response to LPS. SM strongly stimulated heme oxygenase 1 (HO-1 expression and addition of zinc protoporphyrin (ZnPP, a HO-1 competitive inhibitor, reversed the inhibition of NO production, indicating the involvement of HO-1 in its anti-inflammatory activity. The effects observed in this study provide evidence for the reuse of residues from C. tenuifloria in the food additive, medicine and cosmetic industries.

Sustainable utilization of waste palm oil and sulfonated carbon catalyst derived from coconut meal residue for biodiesel production.

Science.gov (United States)

Thushari, Indika; Babel, Sandhya

2018-01-01

In this study, an inexpensive, environmental benign acid catalyst is prepared using coconut meal residue (CMR) and employed for biodiesel production from waste palm oil (WPO). The total acid density of the catalyst is found to be 3.8mmolg -1 . The catalyst shows a unique amorphous structure with 1.33m 2 g -1 of surface area and 0.31cm 3 g -1 of mean pore volume. Successful activation is confirmed by Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The highest biodiesel yield of 92.7% was obtained from WPO in an open reflux system using the catalyst. Results show that biodiesel yield increases with increasing methanol:oil (molar ratio) and reaction time up to an optimum value. It is found that the catalyst can be reused for at least four cycles for >80% biodiesel yield. Fuel properties of the produced biodiesel meet international biodiesel standards. Copyright © 2017 Elsevier Ltd. All rights reserved.

Semi-automatic image analysis methodology for the segmentation of bubbles and drops in complex dispersions occurring in bioreactors

Science.gov (United States)

Taboada, B.; Vega-Alvarado, L.; Córdova-Aguilar, M. S.; Galindo, E.; Corkidi, G.

2006-09-01

Characterization of multiphase systems occurring in fermentation processes is a time-consuming and tedious process when manual methods are used. This work describes a new semi-automatic methodology for the on-line assessment of diameters of oil drops and air bubbles occurring in a complex simulated fermentation broth. High-quality digital images were obtained from the interior of a mechanically stirred tank. These images were pre-processed to find segments of edges belonging to the objects of interest. The contours of air bubbles and oil drops were then reconstructed using an improved Hough transform algorithm which was tested in two, three and four-phase simulated fermentation model systems. The results were compared against those obtained manually by a trained observer, showing no significant statistical differences. The method was able to reduce the total processing time for the measurements of bubbles and drops in different systems by 21-50% and the manual intervention time for the segmentation procedure by 80-100%.

Are the toroidal shapes of heavy-ion reactions seen in macroscopic drop collisions?

International Nuclear Information System (INIS)

Menchaca R, A.; Borunda, M.; Hidalgo, S.S.; Huidobro, F.; Michaelian, K.; Perez, A.; Rodriguez, V.

1996-01-01

Experiments involving the collisions of water, and mineral oil, drops are reported. The aim is to search for toroidal configurations predicted by, both, macroscopic fluid dynamic and nuclear models. Instead, we find the formation of thin liquid sheets surrounded by a somewhat thicker rim presenting a fingering instability. (Author)

A New Era of Oil Abundance?

International Nuclear Information System (INIS)

Aoun, Marie-Claire

2015-09-01

From 2014 to 2015, the price of oil fell. The price drop is explained by several factors: a significant increase of oil production in the United States, the resumption of Libyan and Iraqi exports, the possible lifting of sanctions against Iran, and slowing growth in developing countries. The situation is having negative effects on oil-producing countries, but the Organization of the Petroleum Exporting Countries (OPEC) remains divided as to its stance on the situation, making it all the more difficult to predict future trends in oil prices. Reprint of an article published in 'Politique Etrangere', vol. 80, no.4, Winter 2015. (author)

The deep processing of oil residues conjunction with shales

Directory of Open Access Journals (Sweden)

Anatoly Maloletnev

2012-12-01

Full Text Available The results of studies on the development of a new process of thermal cracking of tar oil as a slurry with crushed oil shale to obtain components of motor fuels. The results suggest doubtless advantages of the process before the industrial of thermo cracking, since the single-stage processing of raw materials in relatively in the mild conditions (5 MPa, 425ºC, volumetric feed rate 1.0 h-1 is achieved deep destruction of tar oil (the yield petrol fraction with a bp amounts to up to 180ºC - ~12 mass % of middle distillates with a bp 180-360ºC – 43-44 mass %, of raw material for catalytic cracking of a bp 360-520ºC – ~15-16%, based on the initial tar oil. Formed like coke products and raw materials contained in V and Ni is postponed on the mineral part of slate and removed from the reaction zone with the liquid products of the process.

Experimental Investigation of Two-Phase Oil (D130)-Water Flow in 4″ Pipe for Different Inclination Angles

Science.gov (United States)

Shaahid, S. M.; Basha, Mehaboob; Al-Hems, Luai M.

2018-03-01

Oil and water are often produced and transported together in pipelines that have various degrees of inclination from the horizontal. The flow of two immiscible liquids oil and water in pipes has been a research topic since several decades. In oil and chemical industries, knowledge of the frictional pressure loss in oil-water flows in pipes is necessary to specify the size of the pump required to pump the emulsions. An experimental investigation has been carried out for measurement of pressure drop of oil (D130)-water two-phase flows in 4 inch diameter inclined stainless steel pipe at different flow conditions. Experiments were conducted for different inclination angles including; 0°, 15°, 30° (for water cuts “WC” 0 - 100%). The flow rates at the inlet were varied from 4000 to 8000 barrels-per-day (BPD). For a given flow rate the frictional pressure drop has been found to increase (for all angles) from WC = 0 - 60%, and thereafter friction pressure drop decreases, this could be due phase inversion. For a given WC 40%, the frictional pressure drop has been found to increase with angle and flow rate. It has been noticed that inclination angle has appreciable effect on frictional pressure drop.

Oil supply and demand

International Nuclear Information System (INIS)

Rech, O.

2004-01-01

World oil demand, driven by economic development in China, posted the highest growth rate in 20 years. In a context of geopolitical uncertainty, prices are soaring, encouraged by low inventory and the low availability of residual production capacity. Will 2004 bring a change in the oil market paradigm? (author)

Oil supply and demand

Energy Technology Data Exchange (ETDEWEB)

Rech, O

2004-07-01

World oil demand, driven by economic development in China, posted the highest growth rate in 20 years. In a context of geopolitical uncertainty, prices are soaring, encouraged by low inventory and the low availability of residual production capacity. Will 2004 bring a change in the oil market paradigm? (author)

The H-Oil Process : Preferred configurations for application to western Canadian feedstocks

International Nuclear Information System (INIS)

Colyar, J.J.; Peer, E.D.

1997-01-01

The technical and economic evaluation of a method used to convert and upgrade petroleum residua and heavy oils into lighter products was described. The feasibility of applying the process to typical western Canadian oil sand feedstocks was evaluated. The H-Oil process, developed by HRI Inc., is an ebullated-bed catalytic hydrocracking process that accounts for more than 50 per cent of the worldwide vacuum residue hydroprocessing market. It has a unique flexibility to handle many different types of heavy crudes while producing clean transportation fuels. The unconverted vacuum residue from the process can be used for fuel oil production, blended into asphalt, or routed to a resid catalytic cracker or coker. The residue can also be directly combusted or gasified to produce hydrogen. Four different technologies that have been used commercially in Canada to upgrade western Canadian heavy oil residue have been reviewed and evaluated from a technical and economic viewpoint. The following improvements in the H-oil process have resulted in greater economy and product quality: (1) development of a new generation of high activity catalysts, (2) development of an improved recycle cup, and (3) new outlets for unconverted residue. It was suggested that the H-Oil process produces more revenue than the delayed coker process. As coke becomes harder to dispose of, the H-Oil process will become more attractive for producing synthetic crude from heavy oil. 6 refs., 9 tabs., 9 figs

Preparation of a Nanoemulsion with Carapa guianensis Aublet (Meliaceae Oil by a Low-Energy/Solvent-Free Method and Evaluation of Its Preliminary Residual Larvicidal Activity

Directory of Open Access Journals (Sweden)

Flávia L. M. Jesus

2017-01-01

Full Text Available Andiroba (Carapa guianensis seeds are the source of an oil with a wide range of biological activities and ethnopharmacological uses. However, few studies have devoted attention to innovative formulations, including nanoemulsions. The present study aimed to obtain a colloidal system with the andiroba oil using a low-energy and organic-solvent-free method. Moreover, the preliminary residual larvicidal activity of the nanoemulsion against Aedes aegypti was evaluated. Oleic and palmitic acids were the major fatty acids, in addition to the phytosterol β-sitosterol and limonoids (tetranortriterpenoids. The required hydrophile-lipophile was around 11.0 and the optimal nanoemulsion was obtained using polysorbate 85. The particle size distribution suggested the presence of small droplets (mean diameter around 150 nm and low polydispersity index (around 0.150. The effect of temperature on particle size distribution revealed that no major droplet size increase occurred. The preliminary residual larvicidal assay suggested that the mortality increased as a function of time. The present study allowed achievement of a potential bioactive oil in water nanoemulsion that may be a promising controlled release system. Moreover, the ecofriendly approach involved in the preparation associated with the great bioactive potential of C. guianensis makes this nanoemulsion very promising for valorization of this Amazon raw material.

Evaluation of the toxicity of the weathered crude oil used at the Newfoundland Offshore Burn Experiment (NOBE) and the resultant burn residue

International Nuclear Information System (INIS)

Blenkinsopp, S.; Sergy, G.; Doe, K.; Wohlgeschaffen, G.; Li, K.; Fingas, M.

1997-01-01

Toxicity of the weathered crude oil Alberta Sweet Mixed Blend (ASMB) used at the Newfoundland Offshore Burn Experiment (NOBE), and the resultant burn residue was evaluated using the newly developed Environment Canada water-accomodated fraction (WAF) method and exposure protocol. Rainbow trout, three-spine stickleback and gametes of sea urchins were exposed to saltwater WAF prepared from both weathered ASMB and burn residue. Gas chromatography/ mass spectrometry headspace analysis of 28 analytes showed low levels of volatile hydrocarbons after 96 hours of exposure (except for sea urchins, in which case the test was only 20 minutes in duration). All samples were found to be not toxic to all species tested. 10 refs., 2 tabs

Experimental Study on Breakdown Characteristics of Transformer Oil Influenced by Bubbles

Directory of Open Access Journals (Sweden)

Chunxu Qin

2018-03-01

Full Text Available Bubbles will reduce the electric strength of transformer oil, and even result in the breakdown of the insulation. This paper has studied the breakdown voltages of transformer oil and oil-impregnated pressboard under alternating current (AC and direct current (DC voltages. In this paper, three types of electrodes were applied: cylinder-plan electrodes, sphere-plan electrodes, and cone-plan electrodes, and the breakdown voltages were measured in both no bubbles and bubbles. The sphere-sphere electrodes were used to study the breakdown voltage of the oil-impregnated pressboard. The results showed that under the influence of bubble, the breakdown voltage of the cylinder-plan electrode dropped the most, and the breakdown voltage of the cone-plan electrode dropped the least. The bubbles motion was the key factor of the breakdown. The discharge types of the oil-impregnated pressboard were different with bubbles, and under DC, the main discharge type was flashover along the oil-impregnated pressboard, while under AC, the main discharge type was breakdown through the oil-impregnated pressboard.

Properties of Residue from Olive Oil Extraction as a Raw Material for Sustainable Construction Materials. Part I: Physical Properties

Directory of Open Access Journals (Sweden)

Almudena Díaz-García

2017-01-01

Full Text Available Action on climate, the environment, and the efficient use of raw materials and resources are important challenges facing our society. Against this backdrop, the construction industry must adapt to new trends and environmentally sustainable construction systems, thus requiring lines of research aimed at keeping energy consumption in new buildings as low as possible. One of the main goals of this research is to efficiently contribute to reducing the amount of residue from olive oil extraction using a two-phase method. This can be achieved by producing alternative structural materials to be used in the construction industry by means of a circular economy. The technical feasibility of adding said residue to ceramic paste was proven by analyzing the changes produced in the physical properties of the paste, which were then compared to the properties of the reference materials manufactured with clay without residue. Results obtained show that the heating value of wet pomace can contribute to the thermal needs of the sintering process, contributing 30% of energy in pieces containing 3% of said material. Likewise, adding larger amounts of wet pomace to the clay body causes a significant decrease in bulk density values.

Properties of Residue from Olive Oil Extraction as a Raw Material for Sustainable Construction Materials. Part I: Physical Properties.

Science.gov (United States)

Díaz-García, Almudena; Martínez-García, Carmen; Cotes-Palomino, Teresa

2017-01-25

Action on climate, the environment, and the efficient use of raw materials and resources are important challenges facing our society. Against this backdrop, the construction industry must adapt to new trends and environmentally sustainable construction systems, thus requiring lines of research aimed at keeping energy consumption in new buildings as low as possible. One of the main goals of this research is to efficiently contribute to reducing the amount of residue from olive oil extraction using a two-phase method. This can be achieved by producing alternative structural materials to be used in the construction industry by means of a circular economy. The technical feasibility of adding said residue to ceramic paste was proven by analyzing the changes produced in the physical properties of the paste, which were then compared to the properties of the reference materials manufactured with clay without residue. Results obtained show that the heating value of wet pomace can contribute to the thermal needs of the sintering process, contributing 30% of energy in pieces containing 3% of said material. Likewise, adding larger amounts of wet pomace to the clay body causes a significant decrease in bulk density values.

Interpreting residues of petroleum hydrocarbons in wildlife tissues

International Nuclear Information System (INIS)

Hall, R.J.; Coon, N.C.

1988-08-01

This report is the first publication in the field of environmental-contaminant effects on wildlife to tell the reader how to interpret the results of analytical chemical results. Specifically, the publication describes how to interpret residues of petroleum hydrocarbons in wildlife tissues. Pollutant oil residues in avian species are emphasized

Effect Supermint oil (Peppermint oil on children's pain during Colonoscopy

Directory of Open Access Journals (Sweden)

M Najafi

2014-04-01

Full Text Available Introduction: Pain during colonoscopy, especially in children, including the challenges faced by the medical team. The aim of study was investigation the analgesic effect Supermint oil (peppermint oil on pain in children during colonoscopy. Methods and Materials: In this clinical trial study, 101 children (7-14 years old candidate colonoscopy were randomly divided into two groups, respectively. About half an hour before the colonoscopy case group (n=51 was administrated oral drops Supermint oil (peppermint oil. Patients were filled a pediatric pain questionnaire. In control group (n=50 filled a questionnaire without any administration. Data were analyzed using SPSS version 11.5 and (T-test and Paired sample t-test, Corraletion,Man withney. Results: Mean value of pain, duration of colonoscopy in control group was 5/60+1/85 and in case group was 4/20+1/70 and this diference was significant (P

Environmental Assessment/Baseline Survey to Establish New Drop Zone (DZ) in Cadiz, Ohio, Pittsburgh Air Reserve Station, Coraopolis, Pennsylvania

Science.gov (United States)

2009-03-01

International Airport LATN Low Altitude Tactical Navigation MACA Military Airspace Collision Avoidance µg/m3 microgram per cubic meter MSL mean sea...Drop Zone in Cadiz, OH The 911 AW has a Military Airspace Collision Avoidance ( MACA ) plan that includes procedures for clearing local airspace prior...existing MACA plan to include activities at the new drop zone. The MACA includes placing a radio call into the local airport to clear local traffic

Influence of pretreatment of agriculture residues on phytase ...

African Journals Online (AJOL)

phytase production. Pretreatment of agriculture residues with water to remove excess inorganic phosphate has significantly enhanced the phytase activity in case of de-oiled rice bran, wheat bran, peanut cake (low and high oil) and coconut cake. Maximum increase of 20.3 times in phytase activity was observed in case of ...

Sun drying of residual annatto seed powder

Directory of Open Access Journals (Sweden)

Dyego da Costa Santos

2015-01-01

Full Text Available Residual annatto seeds are waste from bixin extraction in the food, pharmaceutical and cosmetic industries. Most of this by-product is currently discarded; however, the use of these seeds in human foods through the elaboration of powder added to other commercial powders is seen as a viable option. This study aimed at drying of residual annatto powder, with and without the oil layer derived from the industrial extraction of bixin, fitting different mathematical models to experimental data and calculating the effective moisture diffusivity of the samples. Powder containing oil exhibited the shortest drying time, highest drying rate (≈ 5.0 kg kg-1 min-1 and highest effective diffusivity (6.49 × 10-12 m2 s-1. All mathematical models assessed were a suitable representation of the drying kinetics of powders with and without oil, with R2 above 0.99 and root mean square error values lower than 1.0.

Management of industrial solid residues; Gerenciamento de residuos solidos industriais

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-07-01

This chapter gives an overview on the management of industrial solid wastes, approaching the following subjects: classification of industrial solid residues; directives and methodologies for the management of industrial solid residues; instruments for the management of industrial solid residues; handling, packing, storage and transportation; treatment of industrial solid residues; final disposal - landfill for industrial residues; the problem of treatment and final disposer of domestic garbage in Brazil; recycling of the lubricant oils used in brazil; legislation.

ASEAN grid-connected biomass residues fired cogeneration plants

International Nuclear Information System (INIS)

Adnan, M.F.; Alias, R.

2006-01-01

Energy supply is one of the major concerns in the world. With uncertainty in the main oil suppliers, the oil price is expected to remain high due to continuous demand from the world. Since oil is mostly used for electricity and transportation, its shortage would cause major disruptions in our daily activities. Thus to counter this scenario and faster depletion of fossil fuel resources, various measures have been taken to find alternative source of energy such as renewable energy. One of the renewable energy sources is from biomass residues which is aplenty particularly in ASEAN. Through one of the collaboration programme between ASEAN and EC which is The EC-ASEAN Cogeneration Programme, a number of Full-Scale Demonstration Projects (FSDP) using biomass residues have been commissioned and implemented successfully. Four of the FSDPs in Thailand and Malaysia are connected to the grid. These projects have been operating very well and since the fuel is commonly available in this ASEAN region, duplication should not be a problem. Thus, this paper would highlight the success stories in implementing biomass residues grid connected project while enhancing cooperation between ASEAN and EC. (Author)

Thermal Adsorption Processing Of Hydrocarbon Residues

Directory of Open Access Journals (Sweden)

Sudad H. Al.

2017-04-01

Full Text Available The raw materials of secondary catalytic processes must be pre-refined. Among these refining processes are the deasphalting and demetallization including their thermo adsorption or thermo-contact adsorption variety. In oil processing four main processes of thermo-adsorption refining of hydrocarbon residues are used ART Asphalt Residual Treating - residues deasphaltizing 3D Discriminatory Destructive Distillation developed in the US ACT Adsorption-Contact Treatment and ETCC Express Thermo-Contact Cracking developed in Russia. ART and ACT are processes with absorbers of lift type reactor while 3D and ETCC processes are with an adsorbing reactor having ultra-short contact time of the raw material with the adsorbent. In all these processes refining of hydrocarbon residues is achieved by partial Thermo-destructive transformations of hydrocarbons and hetero-atomic compounds with simultaneous adsorption of the formed on the surface of the adsorbents resins asphaltene and carboids as well as metal- sulphur - and nitro-organic compounds. Demetallized and deasphalted light and heavy gas oils or their mixtures are a quality raw material for secondary deepening refining processes catalytic and hydrogenation cracking etc. since they are characterized by low coking ability and low content of organometallic compounds that lead to irreversible deactivation of the catalysts of these deepening processes.

Influence of Oil Viscosity on Alkaline Flooding for Enhanced Heavy Oil Recovery

Directory of Open Access Journals (Sweden)

Yong Du

2013-01-01

Full Text Available Oil viscosity was studied as an important factor for alkaline flooding based on the mechanism of “water drops” flow. Alkaline flooding for two oil samples with different viscosities but similar acid numbers was compared. Besides, series flooding tests for the same oil sample were conducted at different temperatures and permeabilities. The results of flooding tests indicated that a high tertiary oil recovery could be achieved only in the low-permeability (approximately 500 mD sandpacks for the low-viscosity heavy oil (Zhuangxi, 390 mPa·s; however, the high-viscosity heavy oil (Chenzhuang, 3450 mPa·s performed well in both the low- and medium-permeability (approximately 1000 mD sandpacks. In addition, the results of flooding tests for the same oil at different temperatures also indicated that the oil viscosity put a similar effect on alkaline flooding. Therefore, oil with a high-viscosity is favorable for alkaline flooding. The microscopic flooding test indicated that the water drops produced during alkaline flooding for oils with different viscosities differed significantly in their sizes, which might influence the flow behaviors and therefore the sweep efficiencies of alkaline fluids. This study provides an evidence for the feasibility of the development of high-viscosity heavy oil using alkaline flooding.

Recovery of transuranics from process residues

International Nuclear Information System (INIS)

Gray, J.H.; Gray, L.W.

1987-01-01

Process residues are generated at both the Rocky Flats Plant (RFP) and the Savannah River Plant (SRP) during aqueous chemical and pyrochemical operations. Frequently, process operations will result in either impure products or produce residues sufficiently contaminated with transuranics to be nondiscardable as waste. Purification and recovery flowsheets for process residues have been developed to generate solutions compatible with subsequent Purex operations and either solid or liquid waste suitable for disposal. The ''scrub alloy'' and the ''anode heel alloy'' are examples of materials generated at RFP which have been processed at SRP using the developed recovery flowsheets. Examples of process residues being generated at SRP for which flowsheets are under development include LECO crucibles and alpha-contaminated hydraulic oil

Development of More Effective Biosurfactants for Enhanced Oil Recovery

Energy Technology Data Exchange (ETDEWEB)

McInerney, J.J.; Han, S.O.; Maudgalya, S.; Mouttaki, H.; Folmsbee, M.; Knapp, R.; Nagle, D.; Jackson, B.E.; Stuadt, M.; Frey, W.

2003-01-16

The objectives of this were two fold. First, core displacement studies were done to determine whether microbial processes could recover residual oil at elevated pressures. Second, the importance of biosurfactant production for the recovery of residual oil was studies. In these studies, a biosurfactant-producing, microorganisms called Bacillus licheniformis strain JF-2 was used. This bacterium produces a cyclic peptide biosurfactant that significantly reduces the interfacial tension between oil and brine (7). The use of a mutant deficient in surfactant production and a mathematical MEOR simulator were used to determine the major mechanisms of oil recovery by these two strains.

Numerical approach for enhanced oil recovery with surfactant flooding

Directory of Open Access Journals (Sweden)

Sadegh Keshtkar

2016-03-01

Full Text Available The remained oil in the reservoir after conventional water-flooding processes, forms a dispersed phase in the form of oil drops which is trapped by capillary forces and is almost about 70% of the original oil in the place (OOIP. To reduce oil residual saturation in laboratory experiments and field projects, surfactant flooding is effective via decreasing the interfacial tension mobility ratio between oil and water phases. Estimation of the role of design variables, like chemical concentrations, partition coefficient and injection rate in different performance quantities, considering a heterogeneous and multiphase oil reservoir is a critical stage for optimal design. Increasing demand for oil production from water-flooded reservoirs has caused an increasing interest in surfactant-polymer (SP and alkali-surfactant-polymer (ASP. Modeling minimizes the risk of high cost of chemicals by improving our insight of process. In the present paper, a surfactant compositional flood model for a three-component (water, petroleum and surfactant, two phase (aqueous and oleic system is studied. A homogeneous, two-dimensional, isothermal reservoir with no free gas or alkali is assumed. The governing equations are in three categories: the continuity equations for the transport of each component, Darcy's equation for the transport of each phase and other auxiliary equations. The equations are solved by finite-differences using a procedure implicit in pressure and explicit in saturation. The validation of the model is achieved through comparing the modeling results with CMG simulators and Buckley–Leverett theory. The results of modeling showed good agreement with CMG results, and the comparison with Buckley–Leverett theory is explained according to different assumptions. After validation of the model, in order to investigate sensitivity analysis, the effects of system variables (partition coefficient, surface tension, oil viscosity and surface injection

Distribution of residues and primitive roots

Indian Academy of Sciences (India)

Replacing the function f by g, we get the required estimate for N(p, N). D. Proof of Theorem 1.1. When p = 7, we clearly see that (1, 2) is a consecutive pair of quadratic residue modulo 7. Assume that p ≥ 11. If 10 is a quadratic residue modulo p, then we have (9, 10) as a consecutive pair of quadratic residues modulo p, ...

Liquid oil and residual characteristics of printed circuit board recycle by pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Lin, Kuo-Hsiung [Department of Environmental Engineering and Science, Fooyin University, Kaohsiung, Taiwan (China); Chiang, Hung-Lung, E-mail: hlchiang@mail.cmu.edu.tw [Department of Health Risk Management, China Medical University, Taichung, Taiwan (China)

2014-04-01

Highlights: • Pyrolysis is a technology for recycling of the non-metal fraction of PCBs. • Liquid product constituents were analyzed for PCB pyrolysis. • Water-soluble ionic species were determined for PCB pyrolysis exhaust. - Abstract: Non-metal fractions of waste printed circuit boards (PCBs) were thermally treated (200–500 °C) under nitrogen atmosphere. Carbon, hydrogen, and nitrogen were determined by elemental analyzer, bromine by instrumental neutron activation analysis (INAA), phosphorus by energy dispersive X-ray spectrometer (EDX), and 29 trace elements by inductively coupled plasma atomic emission spectrometer (ICP-AES) and mass spectrometry (ICP-MS) for raw material and pyrolysis residues. Organic compositions of liquid oil were identified by GC (gas chromatography)–MS, trace element composition by ICP system, and 12 water-soluble ions by IC (ionic chromatography). Elemental content of carbon was >450 mg/g, oxygen 300 mg/g, bromine and hydrogen 60 mg/g, nitrogen 30 mg/g, and phosphorus 28 mg/g. Sulfur was trace in PCBs. Copper content was 25–28 mg/g, iron 1.3–1.7 mg/g, tin 0.8–1.0 mg/g and magnesium 0.4–1.0 mg/g; those were the main metals in the raw materials and pyrolytic residues. In the liquid products, carbon content was 68–73%, hydrogen was 10–14%, nitrogen was 4–5%, and sulfur was less than 0.05% at pyrolysis temperatures from 300 to 500 °C. Phenol, 3-bromophenol, 2-methylphenol and 4-propan-2-ylphenol were major species in liquid products, accounting for >50% of analyzed organic species. Bromides, ammonium and phosphate were the main species in water sorption samples for PCB pyrolysis exhaust.

Experimental study of heavy oil-water flow structure effects on relative permeabilities in a fracture filled with heavy oil

Energy Technology Data Exchange (ETDEWEB)

Shad, S.; Gates, I.D.; Maini, B.B. [Calgary Univ., AB (Canada). Dept. of Chemical and Petroleum Engineering]|[Alberta Ingenuity Centre for In Situ Energy, Edmonton, AB (Canada)

2008-10-15

An experimental apparatus was used to investigate the flow of water in the presence of heavy oil within a smooth-walled fracture. Different flow patterns were investigated under a variety of flow conditions. Results of the experiments were used to determine the accuracy of VC, Corey, and Shad and Gates models designed to represent the behaviour of oil wet systems. The relative permeability concept was used to describe the behaviour of multiple phases flowing through porous media. A smooth-walled plexiglass Hele-Shaw cell was used to visualize oil and water flow. Changes in flow rates led to different flow regimes. The experiment demonstrated that water flowed co-currently in the form of droplets or slugs. Decreases in the oil flow rate enlarged the size of the water droplets as well as the velocity, until eventually the droplets coalesced and became water slugs. Droplet appearance or disappearance directly impacted the oil and water saturation levels. Changes in fluid saturation altered the pressure gradient. Darcy's law for the 2 liquid phases were used to calculate relative permeability curves. The study showed that at low water saturation, oil relative permeability reached as high as 2.5, while water relative permeability was lower than unity. In the presence of a continuous water channel, water drops formed in oil, and the velocity of the drops was lower than their velocity under a discontinuous water flow regime. It was concluded that the Shad and Gates model overestimated oil relative permeability and underestimated water relative permeability. 38 refs., 2 tabs., 9 figs.

Oil palm: domestication achieved?

NARCIS (Netherlands)

Gerritsma, W.; Wessel, M.

1997-01-01

The natural habitat of the oil palm comprises very wet and relatively dry niches in the lowland rain forest in West and Central Africa. The domestication of the oil palm started with the extraction of fruits from wild forest resources. When forests were cleared for shifting cultivation, oil palms

Drop Impact Dynamics with Sessile Drops and Geometries: Spreading, Jetting, and Fragmentation

Science.gov (United States)

Tilger, Christopher F.

The tendency of surface tension to cause small parcels of fluid to form into drops allows convenient packaging, transport, dispersal of liquid phase matter. Liquid drop impacts with solids, liquids, and other drops have realized and additional future applications in biological, manufacturing, heat transfer, and combustion systems. Experiments were conducted to investigate the dynamics of multiple drop collisions, rather than the most-studied phenomenon of single drop impacts. Additional drop impacts were performed on rigid hemispheres representing sessile drops, angled substrates, and into the vertex of two tilted surfaces arranged into a vee shape. A qualitative inspection of drop-sessile drop impacts shows distinct post-impact shapes depending on the offset distance between the drops. At intermediate offset distances, distinct jets issue from the overlap region between the two drops projected areas. These jets are observed to reach their maximum extent at a critical offset distance ratio, epsilon epsilon ˜ 0.75-0.80, with substrate contact angle and W e having a lesser effect. Capillary waves that traverse the sessile drop after collision cause a lower aspect ratio liquid column to emanate from the sessile drop opposite the impact. In order to better understand the jetting phenomenon seen in the offset drop-sessile drop impacts, simpler solid geometries are investigated that elicit a similar behavior. Solid hemispheres do not show the singular jetting observed in the fluidic case, however, a simple vee formed by two intersection planar substrates do jet in a similar fashion to the fluidic case. A geometric model with partnered experiments is developed to describe the bisymmetric spread of an impacting drop on an angled substrate. This geometric model is used to guide a time of arrival based model for various features of the drop impact, which is used to predict jetting in various vee channel experiments.

Development of Bottom Oil Recovery Systems. Revised

Science.gov (United States)

2014-02-01

ahead of the filtration process. Stage 6 Disposal: Collection of oil , oiled debris, and decontaminated sand/sediments. 7 NET ENVIRONMENTAL BENEFIT......Sea HFO / 10.7 X 1983 T/V Hanon Jade Yosu, South Korea Heavy Arabian Crude Oil X (salt) ( burn residue) 1984 T/V Alvenus Louisiana Merey

Prediction of aliphatic and aromatic oil-water interfacial tension at temperatures >100 °C using COSMO-RS

DEFF Research Database (Denmark)

Andersson, Martin Peter; Eckert, F.; Reinisch, J.

2017-01-01

As a contribution to the 9th Industrial Fluid Property Simulation Challenge on predicting interfacial tension between water and a set of non-polar oils at temperatures up to 170 °C we have used our first-principles based model, which is based on density functional theory and uses COSMO-RS implicit...... solvent model thermodynamics. Our calculations predict that the oil-water interfacial tension starts to drop significantly for alkanes at temperatures above ∼100 °C, and the oil-water interfacial tension drops significantly with increased temperature already above ∼25 °C for aromatic oils. In the range...

Four Intoxication Cases Related to the Misuse of Sage Oil

Directory of Open Access Journals (Sweden)

Suzan Gündüz

2016-06-01

Full Text Available Infantile colic is excessive crying of infants younger than 4 months. Families of children suffering from infantile colic attend to the emergency department frequently and the etiology is not well-known. However many families of chil­dren suffering from infantile colic try pharmacologic and non-pharmacologic treatment, they are sleepless and ex­hausted and are affected negatively. Sage oil is in volatile form and it is recommended to apply 1-2 drops on plantar and tummy region of the body by massage for the treat­ment of infantile colic. Most of drugs used for infantile colic are drops and used orally. Families who do not learn detailed usage information may use it orally or may pre­sumed another drug while suffering from sleepless and drowsiness. Herein we reported 4 cases of sage oil intoxi­cation because of wrong information of wrong application of sage oil. We aimed to reduce the prescribing of sage oil in the treatment of infantile colic and emphasize to give more information about proper use of sage oil.

The pressure drop factor - a powerful monitoring tool for hydrotreaters; Der Druckverlustfaktor - ein leistungsstarkes Monitoringwerzeug fuer Entschwefelungsanlagen

Energy Technology Data Exchange (ETDEWEB)

Riebel, A.; Kuczera, M. [MiRO Mineraloelraffinerie Oberrhein GmbH und Co. KG, Karlsruhe (Germany); Skyum, L. [Haldor Topsoe, Lyngby (Denmark)

2004-08-01

In order to reduce traffic air pollution the sulphur content in gasoline and diesel of 50 ppm was appointed Europe-wide for 2005 according to the auto oil programme (aop.) The Mineraloelraffinerie Oberrhein (MiRO-refinery) in Karlsruhe delivers gasoline and diesel with sulphur content below 10 ppm since the 1{sup st} of November 2001. For the deep desulphurisation process temperatures in the reactors had to be raised. Because the catalyst volume was partly considerably increased in order to compensate the thereby caused higher deactivation, now the maximum allowable pressure drop in fixed bed reactors limits the run time for hydrotreaters. Because the pressure drop increases as a first approximation with the squared volume flow, it is hard to distinguish between pressure drop caused by blockades of coke, polymerisation and corrosion products in the catalyst bed and the influence of changing volume flow due to different process conditions. However this necessary to predict the development of pressure drop in the future in order take the right action. The aim of this work is to calculate the loss of void space in the catalyst bed caused due to particulate matter by adequate pressure drop calculation in order to give recommendation and prepare counteractive measures. Using the existing works a model for calculating the pressure drop in hydro treating reactors was developed, which can determine the reduction of void space caused by coke, polymers or corrosion products. In order to verify the validity of the equations from pure gas phase to the trickle bed reactor a gasoline hydrotreater (100% gas phase), a hydrotreater for kerosene (98% gas phase) and a vacuum gas oil hydrotreater (83% gas phase) were regarded. Measured and calculated data match satisfyingly. The presented pressure drop factor takes into account the grown importance of pressure drop in hydrotreaters. The effects of operational changes or feed impurities can be identified in good time and counteractive

Antimicrobial and Herbal Drug Resistance in Enteric Bacteria Isolated from Faecal Droppings of Common House Lizard/Gecko (Hemidactylus frenatus

Directory of Open Access Journals (Sweden)

Bhoj R. Singh

2013-01-01

Full Text Available From 194 faecal dropping samples of common house geckos collected from offices (60, houses (88, integrated farm units (IFS,18 and hostels, guest houses, and dining rooms of different canteen/mess (HGM, 28, 326 bacterial isolates of enteric bacteria belonging to 17 genera and 34 species were detected. Escherichia coli were the most frequently (39 isolated followed by Citrobacter freundii (33, Klebsiella pneumonia (27, Salmonella indica (12, Enterobacter gergoviae (12, and Ent. agglomerans (11. Other important bacteria isolated from gecko droppings were Listonella damsela (2, Raoultella terrigena (3, S. salamae (2, S. houtenae (3, Edwardsiella tarda (4, Edwardsiella hoshinae (1, and Klebsiella oxytoca (2. Of the 223 isolates tested for antimicrobial drug sensitivity, 27 (12.1% had multiple drug resistance (MDR. None of the salmonellae or edwardsiellae had MDR however, MDR strains were significantly more common among Escherichia spp. (P=1.9×10-5 and isolates from IFS units (P=3.58×10-23. The most effective herbal drug, Ageratum conyzoides extract, inhibited growth of only 27.8% of strains tested followed by ethanolic extract of Zanthoxylum rhetsa (13.9%, eucalyptus oil (5.4%, patchouli oil (5.4%, lemongrass oil (3.6%, and sandalwood oil (3.1%, and Artemisia vulgaris essential oil (3.1%.

Hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Foorwood, G F; Taplay, J G

1916-12-12

Hydrocarbon oils are hydrogenated, cracked, or treated for the removal of sulfur by bringing their vapors mixed with steam at temperatures between 450 and 600/sup 0/C into contact with a form of carbon that is capable of decomposing steam with the production of nascent hydrogen at those temperatures. The forms of carbon used include lamp-black, soot, charcoals derived from wood, cellulose, and lignite, and carbons obtained by carbonizing oil residues and other organic bodies at temperatures below 600/sup 0/C. The process is applied to the treatment of coal oil, shale oil, petroleum, and lignite oil. In examples, kerosene is cracked at 570/sup 0/C, cracked spirit is hydrogenated at 500/sup 0/C, and shale spirit is desulfurized at 530/sup 0/C. The products are led to a condenser and thence to a scrubber, where they are washed with creosote oil. After desulfurization, the products are washed with dilute caustic soda to remove sulfurretted hydrogen.

Application of preservatives for residual fuels

International Nuclear Information System (INIS)

Gorozpe y Munoz, Tomas

2000-01-01

Due to the high costs of the combust oils (fuel oil 6) used in generators of vapor and in other treatments, makes important consider the use of preservatives that improve the operation of the units from the operative point of view and of environmental control. The author enumerates several of the problems of corrosion, of efficiency in the combustion and of thermal efficiency; in a same way it enumerates several useful preservatives, to be used in residual fuel

Selective retardation of perfume oil evaporation from oil-in-water emulsions stabilized by either surfactant or nanoparticles.

Science.gov (United States)

Binks, Bernard P; Fletcher, Paul D I; Holt, Benjamin L; Beaussoubre, Pascal; Wong, Kenneth

2010-12-07

We have used dynamic headspace analysis to investigate the evaporation rates of perfume oils from stirred oil-in-water emulsions into a flowing gas stream. We compare the behavior of an oil of low water solubility (limonene) and one of high water solubility (benzyl acetate). It is shown how the evaporation of an oil of low water solubility is selectively retarded and how the retardation effect depends on the oil volume fraction in the emulsion. We compare how the evaporation retardation depends on the nature of the adsorbed film stabilizing the emulsion. Surfactant films are less effective than adsorbed films of nanoparticles, and the retardation can be further enhanced by compression of the adsorbed nanoparticle films by preshrinking the emulsion drops.

Agrochemical characterization of vermicomposts produced from residues of Palo Santo (Bursera graveolens) essential oil extraction.

Science.gov (United States)

Carrión-Paladines, Vinicio; Fries, Andreas; Gómez-Muñoz, Beatriz; García-Ruiz, Roberto

2016-12-01

Fruits of Palo Santo (Bursera graveolens) are used for essential oil extraction. The extraction process is very efficient, because up to 3% of the fresh fruits can be transformed into essential oil; however, a considerable amount of waste is concurrently produced (>97% of the fresh biomass). Recent developments in Ecuadorian policies to foster environmentally friendly agroforestry and industrial practices have led to widespread interest in reusing the waste. This study evaluated the application of four vermicomposts (VMs), which are produced from the waste of the Palo Santo fruit distillation in combination with other raw materials (kitchen leftovers, pig manure, goat manure, and King Grass), for agrochemical use and for carbon (C) and nitrogen (N) decomposition in two soils with different textures. The results showed that the vermicompost mixtures (VMM) were valuable for agricultural utilisation, because total N (min. 2.63%) was relatively high and the C/N ratio (max. 13.3), as well as the lignin (max. 3.8%) and polyphenol (max. 1.6%) contents were low. In addition, N availability increased for both soil types after the application of the VMM. In contrast, N became immobile during decomposition if the VM of the pure waste was added. This likely occurred because of the relatively low total N (1.16%) content and high C/N ratio (35.0). However, the comparatively low C decomposition of this VM type makes its application highly recommendable as a strategy to increase the levels of organic matter and C, as well as for soil reclamation. Overall, these results suggest that the residues of the Palo Santo essential oil extraction are a potential source for vermicompost production and sustainable agriculture. Copyright © 2016 Elsevier Ltd. All rights reserved.

Revitalizing a mature oil play: Strategies for finding and producing unrecovered oil in frio fluvial-deltaic sandstone reservoirs at South Texas. Annual report, October 1994--October 1995

Energy Technology Data Exchange (ETDEWEB)

Holtz, M.; Knox, P.; McRae, L. [and others

1996-02-01

The Frio Fluvial-Deltaic Sandstone oil play of South Texas has produced nearly 1 billion barrels of oil, yet it still contains about 1.6 billion barrels of unrecovered mobile oil and nearly the same amount of residual oil resources. Interwell-scale geologic facise models of Frio Fluvial-deltaic reservoirs are being combined with engineering assessments and geophysical evaluations in order to determine the controls that these characteristics exert on the location and volume or unrecovered mobile and residual oil. Progress in the third year centered on technology transfer. An overview of project tasks is presented.

Economic Exposure to Oil Price Shocks and the Fragility of Oil-Exporting Countries

Directory of Open Access Journals (Sweden)

Toon Vandyck

2018-04-01

Full Text Available From a price range between 100 and 120 USD (U.S. dollars per barrel in 2011–2014, the crude oil price fell from mid-2014 onwards, reaching a level of 26 USD per barrel in January 2016. Here we assess the economic consequences of this strong decrease in the oil price. A retrospective analysis based on data of the past 25 years sheds light on the vulnerability of oil-producing regions to the oil price volatility. Gross domestic product (GDP and government revenues in many Gulf countries exhibit a strong dependence on oil, while more diversified economies improve resilience to oil price shocks. The lack of a sovereign wealth fund, in combination with limited oil reserves, makes parts of Sub-Saharan Africa particularly vulnerable to sustained periods of low oil prices. Next, we estimate the macroeconomic impacts of a 60% oil price drop for all regions in the world. A numerical simulation yields a global GDP increase of roughly 1% and illustrates how the regional impact on GDP relates to oil export dependence. Finally, we reflect on the broader implications (such as migration flows of macroeconomic responses to oil prices and look ahead to the challenge of structural change in a world committed to limiting global warming.

A fundamental research for upgrading heavy oil using syngas as hydrogen source

Energy Technology Data Exchange (ETDEWEB)

Yan, D.; Yuan, M.; Sun, X.; Zhao, S. [China Univ. of Petroleum, Beijing (China). State Key Laboratory of Heavy Oil Processing

2006-07-01

The stock of heavy oil and residue from petroleum fractions has become more important as a component in supplying demands for fuel and petrochemical feeds. Finding economical means of upgrading heavy oils is extremely important in order to ensure future fuel supply. A number of new technologies for upgrading heavy oils have been evaluated, including residual fluid catalytic cracking (RFCC), hydrogenation, thermal conversion, and solvent deasphalting. However, the commercial application of such technologies is mainly constrained by the metal and residual carbon concentrations that are present in all heavy oils. Conventional technologies used to upgrade vacuum residue (VR) result in heavy coke formation, with a consequential reduction in the life of expensive, high-performance catalysts. The hydro upgrading process can significantly remove the concentration of heteroatom such as sulfur, nitrogen, and metals in the liquid products. This paper investigated upgrading of heavy oil using syngas as an alternative hydrogen source with a dispersed catalyst. The paper discussed the experiment with reference to the feedstock and catalyst precursors; finely dispersed catalysts preparation; experimental apparatus; experimental design and procedure; and analysis. The results were presented in terms of effects of catalyst dispersion; effect of hydro-upgrading heavy oil using syngas as alternative source; and effects of different catalysts on residue hydrocracking. Last, the paper discussed the properties of the hydrocracked oil treated with syngas. The study confirmed the effectiveness of the slurry bed hydrocracking catalyst using syngas as a hydrogen source. 23 refs., 8 tabs., 16 figs.

Modification of Lightweight Aggregates’ Microstructure by Used Motor Oil Addition

Science.gov (United States)

Franus, Małgorzata; Jozefaciuk, Grzegorz; Bandura, Lidia; Lamorski, Krzysztof; Hajnos, Mieczysław; Franus, Wojciech

2016-01-01

An admixture of lightweight aggregate substrates (beidellitic clay containing 10 wt % of natural clinoptilolite or Na-P1 zeolite) with used motor oil (1 wt %–8 wt %) caused marked changes in the aggregates’ microstructure, measured by a combination of mercury porosimetry (MIP), microtomography (MT), and scanning electron microscopy. Maximum porosity was produced at low (1%–2%) oil concentrations and it dropped at higher concentrations, opposite to the aggregates’ bulk density. Average pore radii, measured by MIP, decreased with an increasing oil concentration, whereas larger (MT) pore sizes tended to increase. Fractal dimension, derived from MIP data, changed similarly to the MIP pore radius, while that derived from MT remained unaltered. Solid phase density, measured by helium pycnometry, initially dropped slightly and then increased with the amount of oil added, which was most probably connected to changes in the formation of extremely small closed pores that were not available for He atoms. PMID:28773964

Modification of Lightweight Aggregates’ Microstructure by Used Motor Oil Addition

Directory of Open Access Journals (Sweden)

Małgorzata Franus

2016-10-01

Full Text Available An admixture of lightweight aggregate substrates (beidellitic clay containing 10 wt % of natural clinoptilolite or Na-P1 zeolite with used motor oil (1 wt %–8 wt % caused marked changes in the aggregates’ microstructure, measured by a combination of mercury porosimetry (MIP, microtomography (MT, and scanning electron microscopy. Maximum porosity was produced at low (1%–2% oil concentrations and it dropped at higher concentrations, opposite to the aggregates’ bulk density. Average pore radii, measured by MIP, decreased with an increasing oil concentration, whereas larger (MT pore sizes tended to increase. Fractal dimension, derived from MIP data, changed similarly to the MIP pore radius, while that derived from MT remained unaltered. Solid phase density, measured by helium pycnometry, initially dropped slightly and then increased with the amount of oil added, which was most probably connected to changes in the formation of extremely small closed pores that were not available for He atoms.

Alkaline hydrothermal liquefaction of swine carcasses to bio-oil

Energy Technology Data Exchange (ETDEWEB)

Zheng, Ji-Lu, E-mail: triace@163.com; Zhu, Ming-Qiang; Wu, Hai-tang

2015-09-15

Highlights: • Swine carcasses can be converted to bio-oil by alkaline hydrothermal liquefaction. • It seems that the use of the bio-oil for heat or CHP is technically suitable. • Some valuable chemicals were found in the bio-oils. • The bio-oil and the solid residue constituted an energy efficiency of 93.63% for the feedstock. • The solid residue can be used as a soil amendment, to sequester C and for preparing activated carbon. - Abstract: It is imperative that swine carcasses are disposed of safely, practically and economically. Alkaline hydrothermal liquefaction of swine carcasses to bio-oil was performed. Firstly, the effects of temperature, reaction time and pH value on the yield of each liquefaction product were determined. Secondly, liquefaction products, including bio-oil and solid residue, were characterized. Finally, the energy recovery ratio (ERR), which was defined as the energy of the resultant products compared to the energy input of the material, was investigated. Our experiment shows that reaction time had certain influence on the yield of liquefaction products, but temperature and pH value had bigger influence on the yield of liquefaction products. Yields of 62.2 wt% bio-oil, having a high heating value of 32.35 MJ/kg and a viscosity of 305cp, and 22 wt% solid residue were realized at a liquefaction temperature of 250 °C, a reaction time of 60 min and a pH value of 9.0. The bio-oil contained up to hundreds of different chemical components that may be classified according to functional groups. Typical compound classes in the bio-oil were hydrocarbons, organic acids, esters, ketones and heterocyclics. The energy recovery ratio (ERR) reached 93.63%. The bio-oil is expected to contribute to fossil fuel replacement in stationary applications, including boilers and furnaces, and upgrading processes for the bio-oil may be used to obtain liquid transport fuels.

Alkaline hydrothermal liquefaction of swine carcasses to bio-oil

International Nuclear Information System (INIS)

Zheng, Ji-Lu; Zhu, Ming-Qiang; Wu, Hai-tang

2015-01-01

Highlights: • Swine carcasses can be converted to bio-oil by alkaline hydrothermal liquefaction. • It seems that the use of the bio-oil for heat or CHP is technically suitable. • Some valuable chemicals were found in the bio-oils. • The bio-oil and the solid residue constituted an energy efficiency of 93.63% for the feedstock. • The solid residue can be used as a soil amendment, to sequester C and for preparing activated carbon. - Abstract: It is imperative that swine carcasses are disposed of safely, practically and economically. Alkaline hydrothermal liquefaction of swine carcasses to bio-oil was performed. Firstly, the effects of temperature, reaction time and pH value on the yield of each liquefaction product were determined. Secondly, liquefaction products, including bio-oil and solid residue, were characterized. Finally, the energy recovery ratio (ERR), which was defined as the energy of the resultant products compared to the energy input of the material, was investigated. Our experiment shows that reaction time had certain influence on the yield of liquefaction products, but temperature and pH value had bigger influence on the yield of liquefaction products. Yields of 62.2 wt% bio-oil, having a high heating value of 32.35 MJ/kg and a viscosity of 305cp, and 22 wt% solid residue were realized at a liquefaction temperature of 250 °C, a reaction time of 60 min and a pH value of 9.0. The bio-oil contained up to hundreds of different chemical components that may be classified according to functional groups. Typical compound classes in the bio-oil were hydrocarbons, organic acids, esters, ketones and heterocyclics. The energy recovery ratio (ERR) reached 93.63%. The bio-oil is expected to contribute to fossil fuel replacement in stationary applications, including boilers and furnaces, and upgrading processes for the bio-oil may be used to obtain liquid transport fuels

Carbaryl residues in maize products

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Mansour, S.A.; Mostafa, I.Y.; Hassan, A.

1976-01-01

The 14 C-labelled insecticide carbaryl was synthesized from [1- 14 C]-1-naphthol at a specific activity of 3.18mCig -1 . Maize plants were treated with the labelled insecticide under simulated conditions of agricultural practice. Mature plants were harvested and studied for distribution of total residues in untreated grains as popularly roasted and consumed, and in the corn oil and corn germ products. Total residues found under these conditions in the respective products were 0.2, 0.1, 0.45 and 0.16ppm. (author)

Comparative assessment of structural-mechanical properties of heavy oils of timano-pechorskaya province

Directory of Open Access Journals (Sweden)

Н. К. Кондрашева

2017-06-01

Full Text Available The physicochemical properties of heavy oils of Yaregskoe and Usinskoe deposits and the residues of atmospheric distillation of petroleum (fuel oil recovered from them are presented. The group composition of oil and the residues of its atmospheric distillation (fuel oil is determined. When using X-ray fluorescence energy dispersive spectrometer, the content of metals in the products is determined. A conclusion is drawn about the distribution of metals in the initial oil and fuel oil. On the basis of rheological characteristics, the type of liquids is determined in accordance with Newton's law, as well as the presence of an anomaly in the viscosity of the studied media at different temperatures. The energy values of the thixotropy of heavy oils of Usinskoe and Yaregskoe deposits, as well as the activation energy of the viscous flow of all media studied, are obtained. The phase transition of atmospheric residues at 60 °C is discovered. Dependences of the enthalpy and entropy of the viscous flow of the studied hydrocarbon media are obtained with an increase in temperature from 10 to 140 °C. The dependences of the oil molecules and atmospheric residues jumping frequency on viscosity are obtained for the first time.

Characterization of Bottom and Fly Ashes Generated Co-incineration of Biomass with Automotive Shredder Residue

Directory of Open Access Journals (Sweden)

Othaman Muhamad Fazli

2017-01-01

Full Text Available One of the viable techniques to reduce land filling of automotive shredder residue is by co-incinerating them with biomass. This study focuses on characterization of bottom and fly ashes produced from the coincineration of the automotive shredded residue with oil palm biomass. The co-incineration was carried out in a pilot-scale fluidized bed incinerator. The oil palm biomass used was oil palm shell while the automotive shredded residue was obtained from a local recycling company. The characterization was done based on particle size distribution, morphology (SEM analysis and chemical composition (EDS analysis. In term of chemical composition the ashes contain C (Carbon, O (Oxygen, Si (Silicon, K (Potassium, Ca (Calcium and Fe (Ferum.

Oils, paintings and chemistry

Directory of Open Access Journals (Sweden)

Maria Eduarda Machado de Araújo

2005-01-01

Full Text Available In oil paintings artists use oils to apply pigments. These oils firstly are liquid and then solidify in a thin film. Many chemical reactions are involved in drying and also in the aging of these oils. Drying is a continuous process that begins with the oxidation of insaturated fatty acids from triglycerides to originate peroxides. These compounds suffer a cascade of reactions that lead to cross linking bonds between fatty acids residues, transforming the oil in a solid film. Identification of the film oil is possible using the palmitic/stearic ratio (P/S by chromatographic (GC and/or spectroscopic techniques. Sterol composition, phytosterols or cholesterol, determined by GC-MS or FTIR techniques, allows investigators to distinguish between oil painting and a temper one that used egg as the binding medium.

Aerobic microbial enhanced oil recovery

Energy Technology Data Exchange (ETDEWEB)

Torsvik, T. [Univ. of Bergen (Norway); Gilje, E.; Sunde, E.

1995-12-31

In aerobic MEOR, the ability of oil-degrading bacteria to mobilize oil is used to increase oil recovery. In this process, oxygen and mineral nutrients are injected into the oil reservoir in order to stimulate growth of aerobic oil-degrading bacteria in the reservoir. Experiments carried out in a model sandstone with stock tank oil and bacteria isolated from offshore wells showed that residual oil saturation was lowered from 27% to 3%. The process was time dependent, not pore volume dependent. During MEOR flooding, the relative permeability of water was lowered. Oxygen and active bacteria were needed for the process to take place. Maximum efficiency was reached at low oxygen concentrations, approximately 1 mg O{sub 2}/liter.

Drop rebound after impact: the role of the receding contact angle.

Science.gov (United States)

Antonini, C; Villa, F; Bernagozzi, I; Amirfazli, A; Marengo, M

2013-12-31

Data from the literature suggest that the rebound of a drop from a surface can be achieved when the wettability is low, i.e., when contact angles, measured at the triple line (solid-liquid-air), are high. However, no clear criterion exists to predict when a drop will rebound from a surface and which is the key wetting parameter to govern drop rebound (e.g., the "equilibrium" contact angle, θeq, the advancing and the receding contact angles, θA and θR, respectively, the contact angle hysteresis, Δθ, or any combination of these parameters). To clarify the conditions for drop rebound, we conducted experimental tests on different dry solid surfaces with variable wettability, from hydrophobic to superhydrophobic surfaces, with advancing contact angles 108° contact angles 89° contact angle is the key wetting parameter that influences drop rebound, along with surface hydrophobicity: for the investigated impact conditions (drop diameter 2.4 contact angles higher than 100°. Also, the drop rebound time decreased by increasing the receding contact angle. It was also shown that in general care must be taken when using statically defined wetting parameters (such as advancing and receding contact angles) to predict the dynamic behavior of a liquid on a solid surface because the dynamics of the phenomenon may affect surface wetting close to the impact point (e.g., as a result of the transition from the Cassie-Baxter to Wenzel state in the case of the so-called superhydrophobic surfaces) and thus affect the drop rebound.

Degradability of n-alkanes during ex situ natural bioremediation of soil contaminated by heavy residual fuel oil (mazut

Directory of Open Access Journals (Sweden)

Ali Ramadan Mohamed Muftah

2013-01-01

Full Text Available It is well known that during biodegradation of oil in natural geological conditions, or oil pollutants in the environment, a degradation of hydrocarbons occurs according to the well defined sequence. For example, the major changes during the degradation process of n-alkanes occur in the second, slight and third, moderate level (on the biodegradation scale from 1 to 10. According to previous research, in the fourth, heavy level, when intensive changes of phenanthrene and its methyl isomers begin, n-alkanes have already been completely removed. In this paper, the ex situ natural bioremediation (unstimulated bioremediation, without addition of biomass, nutrient substances and biosurfactant of soil contaminated with heavy residual fuel oil (mazut was conducted during the period of 6 months. Low abundance of n-alkanes in the fraction of total saturated hydrocarbons in the initial sample (identification was possible only after concentration by urea adduction technique showed that the investigated oil pollutant was at the boundary between the third and the fourth biodegradation level. During the experiment, an intense degradation of phenanthrene and its methyl-, dimethyl-and trimethyl-isomers was not followed by the removal of the remaining n-alkanes. The abundance of n-alkanes remained at the initial low level, even at end of the experiment when the pollutant reached one of the highest biodegradation levels. These results showed that the unstimulated biodegradation of some hydrocarbons, despite of their high biodegradability, do not proceed completely to the end, even at final degradation stages. In the condition of the reduced availability of some hydrocarbons, microorganisms tend to opt for less biodegradable but more accessible hydrocarbons.

'Cryptogenic Drop Attacks' revisited: evidence of overlap with functional neurological disorder.

Science.gov (United States)

Hoeritzauer, Ingrid; Carson, Alan J; Stone, Jon

2018-02-07

In their 1973 BMJ paper 'Cryptogenic Drop Attacks', Stevens and Matthews described 40, mostly middle-aged, female patients with drop attacks of unknown cause. Although clinically common, there has been little on this topic since. We aimed to determine clinical features, comorbidity and outcome of patients with drop attacks. We carried out a retrospective review of patients with cryptogenic drop attacks seen consecutively by one clinician (JS) between 2006 and 2016. Demographics, phenomenology, duration and frequency of attacks, attack description and comorbid diagnoses were recorded. Patients were followed up with a notes review. 83 patients with cryptogenic drop attacks were predominantly female (89%, n=79), mean age 44  years. The majority (93%, n=77) could not remember the fall itself and almost half (43%, n=36) experienced prodromal dissociative symptoms. Mechanical trips or syncope preceded drop attacks, historically, in 24% (n=20) of cases. Persistent fatigue (73%, n=61), chronic pain (40%, n=33), functional limb weakness (31%,n=26) and dissociative (non-epileptic) attacks 28% (n=23) were common, with the latter usually preceding or emerging from drop attacks. At follow-up (88%, mean 38 months), 28% (n=23) had resolution of their drop attacks. Predisposing (but non-causative) disease comorbidity was found at baseline (n=12) and follow-up (n=5). Cryptogenic drop attacks are associated with high frequency of comorbid functional somatic and functional neurological disorders. Patients commonly have prodromal dissociative symptoms and in some there was a clear relationship with prior or subsequent dissociative (non-epileptic) attacks. Some cryptogenic drop attacks may be best understood as phenomena on the spectrum of dissociative attacks. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Characterization of residual oils for biodiesel production

Directory of Open Access Journals (Sweden)

Edmilson Antonio Canesin

2014-01-01

Conclusions: The obtained results suggesting that it is possible to take advantage of these residues for biodiesel production as the obtained products were approved according to the rules established by the National Association of Petroleum (ANP; the bovine samples were the exception regarding moisture and acidity.

A mix-and-read drop-based in vitro two-hybrid method for screening high-affinity peptide binders

Science.gov (United States)

Cui, Naiwen; Zhang, Huidan; Schneider, Nils; Tao, Ye; Asahara, Haruichi; Sun, Zhiyi; Cai, Yamei; Koehler, Stephan A.; de Greef, Tom F. A.; Abbaspourrad, Alireza; Weitz, David A.; Chong, Shaorong

2016-01-01

Drop-based microfluidics have recently become a novel tool by providing a stable linkage between phenotype and genotype for high throughput screening. However, use of drop-based microfluidics for screening high-affinity peptide binders has not been demonstrated due to the lack of a sensitive functional assay that can detect single DNA molecules in drops. To address this sensitivity issue, we introduced in vitro two-hybrid system (IVT2H) into microfluidic drops and developed a streamlined mix-and-read drop-IVT2H method to screen a random DNA library. Drop-IVT2H was based on the correlation between the binding affinity of two interacting protein domains and transcriptional activation of a fluorescent reporter. A DNA library encoding potential peptide binders was encapsulated with IVT2H such that single DNA molecules were distributed in individual drops. We validated drop-IVT2H by screening a three-random-residue library derived from a high-affinity MDM2 inhibitor PMI. The current drop-IVT2H platform is ideally suited for affinity screening of small-to-medium-sized libraries (103–106). It can obtain hits within a single day while consuming minimal amounts of reagents. Drop-IVT2H simplifies and accelerates the drop-based microfluidics workflow for screening random DNA libraries, and represents a novel alternative method for protein engineering and in vitro directed protein evolution. PMID:26940078

Catalytic hydroprocessing of heavy oil feedstocks

International Nuclear Information System (INIS)

Okunev, A G; Parkhomchuk, E V; Lysikov, A I; Parunin, P D; Semeikina, V S; Parmon, V N

2015-01-01

A grave problem of modern oil refining industry is continuous deterioration of the produced oil quality, on the one hand, and increase in the demand for motor fuels, on the other hand. This necessitates processing of heavy oil feedstock with high contents of sulfur, nitrogen and metals and the atmospheric residue. This feedstock is converted to light oil products via hydrogenation processes catalyzed by transition metal compounds, first of all, cobalt- or nickel-promoted molybdenum and tungsten compounds. The processing involves desulfurization, denitrogenation and demetallization reactions as well as reactions converting heavy hydrocarbons to lighter fuel components. The review discusses the mechanisms of reactions involved in the heavy feedstock hydroprocessing, the presumed structure and state of the catalytically active components and methods for the formation of supports with the desired texture. Practically used and prospective approaches to catalytic upgrading of heavy oil feedstock as well as examples of industrial processing of bitumen and vacuum residues in the presence of catalysts are briefly discussed. The bibliography includes 140 references

Catalytic hydroprocessing of heavy oil feedstocks

Science.gov (United States)

Okunev, A. G.; Parkhomchuk, E. V.; Lysikov, A. I.; Parunin, P. D.; Semeikina, V. S.; Parmon, V. N.

2015-09-01

A grave problem of modern oil refining industry is continuous deterioration of the produced oil quality, on the one hand, and increase in the demand for motor fuels, on the other hand. This necessitates processing of heavy oil feedstock with high contents of sulfur, nitrogen and metals and the atmospheric residue. This feedstock is converted to light oil products via hydrogenation processes catalyzed by transition metal compounds, first of all, cobalt- or nickel-promoted molybdenum and tungsten compounds. The processing involves desulfurization, denitrogenation and demetallization reactions as well as reactions converting heavy hydrocarbons to lighter fuel components. The review discusses the mechanisms of reactions involved in the heavy feedstock hydroprocessing, the presumed structure and state of the catalytically active components and methods for the formation of supports with the desired texture. Practically used and prospective approaches to catalytic upgrading of heavy oil feedstock as well as examples of industrial processing of bitumen and vacuum residues in the presence of catalysts are briefly discussed. The bibliography includes 140 references.

A drop penetration method to measure powder blend wettability.

Science.gov (United States)

Wang, Yifan; Liu, Zhanjie; Muzzio, Fernando; Drazer, German; Callegari, Gerardo

2018-03-01

Water wettability of pharmaceutical blends affects important quality attributes of final products. We investigate the wetting properties of a pharmaceutical blend lubricated with Magnesium Stearate (MgSt) as a function of the mechanical shear strain applied to the blend. We measure the penetration dynamics of sessile drops deposited on slightly compressed powder beds. We consider a blend composed of 9% Acetaminophen 90% Lactose and 1% MgSt by weight. Comparing the penetration time of water and a reference liquid Polydimethylsiloxane (silicon oil) we obtain an effective cosine of the contact angle with water, based on a recently developed drop penetration method. We repeat the experiments for blends exposed to increasing levels of shear strain and demonstrate a significant decrease in water wettability (decrease in the cosine of the contact angle). The results are consistent with the development of a hydrophobic film coating the powder particles as a result of the increased shear strain. Finally, we show that, as expected dissolution times increase with the level of shear strain. Therefore, the proposed drop penetration method could be used to directly assess the state of lubrication of a pharmaceutical blend and act as a quality control on powder blend attributes before the blend is tableted. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of olive and sunflower seed oil on the adult skin barrier: implications for neonatal skin care.

Science.gov (United States)

Danby, Simon G; AlEnezi, Tareq; Sultan, Amani; Lavender, Tina; Chittock, John; Brown, Kirsty; Cork, Michael J

2013-01-01

Natural oils are advocated and used throughout the world as part of neonatal skin care, but there is an absence of evidence to support this practice. The goal of the current study was to ascertain the effect of olive oil and sunflower seed oil on the biophysical properties of the skin. Nineteen adult volunteers with and without a history of atopic dermatitis were recruited into two randomized forearm-controlled mechanistic studies. The first cohort applied six drops of olive oil to one forearm twice daily for 5 weeks. The second cohort applied six drops of olive oil to one forearm and six drops of sunflower seed oil to the other twice daily for 4 weeks. The effect of the treatments was evaluated by determining stratum corneum integrity and cohesion, intercorneocyte cohesion, moisturization, skin-surface pH, and erythema. Topical application of olive oil for 4 weeks caused a significant reduction in stratum corneum integrity and induced mild erythema in volunteers with and without a history of atopic dermatitis. Sunflower seed oil preserved stratum corneum integrity, did not cause erythema, and improved hydration in the same volunteers. In contrast to sunflower seed oil, topical treatment with olive oil significantly damages the skin barrier, and therefore has the potential to promote the development of, and exacerbate existing, atopic dermatitis. The use of olive oil for the treatment of dry skin and infant massage should therefore be discouraged. These findings challenge the unfounded belief that all natural oils are beneficial for the skin and highlight the need for further research. © 2012 Wiley Periodicals, Inc.

Oil and the world economy: some possible futures.

Science.gov (United States)

Kumhof, Michael; Muir, Dirk

2014-01-13

This paper, using a six-region dynamic stochastic general equilibrium model of the world economy, assesses the output and current account implications of permanent oil supply shocks hitting the world economy. For modest-sized shocks and conventional production technologies, the effects are modest. But for larger shocks, for elasticities of substitution that decline as oil usage is reduced to a minimum, and for production functions in which oil acts as a critical enabler of technologies, output growth could drop significantly. Also, oil prices could become so high that smooth adjustment, as assumed in the model, may become very difficult.

Construction of VLCC marine oil storage cost index system

Science.gov (United States)

Li, Yuan; Li, Yule; Lu, Jinshu; Wu, Wenfeng; Zhu, Faxin; Chen, Tian; Qin, Beichen

2018-04-01

VLCC as the research object, the basic knowledge of VLCC is summarized. According to the phenomenon that VLCC is applied to offshore oil storage gradually, this paper applies the theoretical analysis method to analyze the excess capacity from VLCC, the drop of oil price, the aging VLCC is more suitable for offshore storage The paper analyzes the reason of VLCC offshore oil storage from three aspects, analyzes the cost of VLCC offshore storage from the aspects of manpower cost and shipping cost, and constructs the cost index system of VLCC offshore oil storage.

Modifying Char Dustcake Pressure Drop Using Particulate Additives

Energy Technology Data Exchange (ETDEWEB)

Landham, C.; Dahlin, R.S.; Martin, R.A.; Guan, X.

2002-09-19

Coal gasification produces residual particles of coal char, coal ash, and sorbent that are suspended in the fuel gas stream exiting the gasifier. In most cases, these particles (referred to, hereafter, simply as char) must be removed from the stream prior to sending the gas to a turbine, fuel cell, or other downstream device. Currently, the most common approach to cleaning the gas stream at high temperature and pressure is by filtering the particulate with a porous ceramic or metal filter. However, because these dusts frequently have small size distributions, irregular morphology, and high specific surface areas, they can have very high gas flow resistance resulting in hot-gas filter system operating problems. Typical of gasification chars, the hot-gas filter dustcakes produced at the Power Systems Development Facility (PSDF) during recent coal gasification tests have had very high flow resistance (Martin et al, 2002). The filter system has been able to successfully operate, but pressure drops have been high and filter cleaning must occur very frequently. In anticipation of this problem, a study was conducted to investigate ways of reducing dustcake pressure drop. This paper will discuss the efficacy of adding low-flow-resistance particulate matter to the high-flow-resistance char dustcake to reduce dustcake pressure drop. The study had two parts: a laboratory screening study and confirming field measurements at the PSDF.

Life cycle assessment of two palm oil production systems

International Nuclear Information System (INIS)

Stichnothe, Heinz; Schuchardt, Frank

2011-01-01

In 2009 approx. 40 Mt of palm oil were produced globally. Growing demand for palm oil is driven by an increasing human population as well as subsidies for biodiesel and is likely to increase further in coming years. The production of 1 t crude palm oil requires 5 t of fresh fruit bunches (FFB). On average processing of 1 t FFB in palm oil mills generates 0.23 t empty fruit bunches (EFB) and 0.65 t palm oil mill effluents (POME) as residues. In this study it is assumed that land use change does not occur. In order to estimate the environmental impacts of palm oil production a worst and a best case scenario are assessed and compared in the present study using 1000 kg of FFB as functional unit. The production and treatment of one t FFB causes more than 460 kg CO 2eq in the worst case scenario and 110 kg CO 2eq in the best case scenario. The significant greenhouse gas (GHG) emission reduction is achieved by co-composting residues of the palm oil mill. Thus treating those residues appropriately is paramount for reducing environmental impacts particularly global warming potential (GWP) and eutrophication potential (EP). Another important contributor to the EP but also to the human toxicity potential (HTP) is the biomass powered combined heat and power (CHP) plant of palm oil mills. Frequently CHP plants of palm oil mills operate without flue gas cleaning. The CHP plant emits heavy metals and nitrogen oxides and these account for 93% of the HTP of the advanced palm oil production system, of which heavy metal emissions to air are responsible for 79%. The exact emission reduction potential from CHP plants could not be quantified due to existing data gaps, but it is apparent that cleaning the exhaust gas would reduce eutrophication, acidification and toxicity considerably. -- Highlights: → We have estimated the environmental impacts of two palm oil production systems. → Residues from palm oil mills are a wasted resource rather than waste. → Co-composting of EFB and

Enzymes for Enhanced Oil Recovery (EOR)

Energy Technology Data Exchange (ETDEWEB)

Nasiri, Hamidreza

2011-04-15

enzymes on interactions in the oil/brine/solid system was studied. It was found that enzymes can change the adhesion behavior of the crude oil on glass surfaces from adhesion to non-adhesion when they are added to the brine solution. This was confirmed by contact angle measurements, which showed that contact angles became more water-wet (i.e. decreased) after exposure to enzyme solutions. Possible mechanisms giving rise to these observations, including catalysis of ester hydrolysis and enzyme adsorption, were discussed and tested. An experimental study of changes in oil-water interfacial properties by addition of enzymes and proteins, including measurements of interfacial tension and electrophoretic mobility, has been performed. It was found that the effect of enzymes on oil-water properties is minor compared to their effect on oil-water-solid properties. Their contribution to change interfacial tension between oil and water is not significant while they affect the electrophoretic mobility of emulsified oil in enzyme-brine solution to some extent. Attempts were also made to study changes in both oil and water phase composition after equilibration with enzymes. However, since the chemical composition of crude oil is highly complex, a model oil was used in some of the experiments. The model oil was chosen to be a water insoluble ester (ethyl decanoate) solved in mineral oil in an effort to verify the possible role of catalysis of ester hydrolysis. Dynamic core displacements using sandstone and carbonate rocks were conducted to show the potential of improved oil recovery by enzyme- and combined enzyme-surfactant flooding. Most of the core flooding experiments commenced with water flooding from initial water saturation, Swi, (established with synthetic sea water) which will be referred to as secondary mode displacements. Accordingly, tertiary oil recovery processes were used to describe injection of enzyme and/or enzyme-surfactant solutions from residual oil saturation, Sor

Vegetable oil spills : oil properties and behaviour

International Nuclear Information System (INIS)

Fingas, M.; Fieldhouse, B.; Jokuty, P.

2001-01-01

In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs

Vegetable oil spills : oil properties and behaviour

Energy Technology Data Exchange (ETDEWEB)

Fingas, M.; Fieldhouse, B.; Jokuty, P. [Environment Canada, Ottawa, ON (Canada). Emergencies Science Div

2001-07-01

In 1997, the United States Environmental Protection Agency conducted a thorough review of the issue regarding vegetable oil spills. Recent attention has refocused on this issue as a result of an incident where 20 tons of canola oil was spilled in the Vancouver Harbour in 2000. In the past, vegetable oils were suggested to be a useful test material because they were thought to be innocuous. It was even suggested they be used to remove petroleum oil residues from beaches. However, recent studies have shown that spills of vegetable oils can have major environmental consequences, equivalent to those of petroleum oil spills. The spills have devastating effects on birds and intertidal organisms. This paper presented a summary of historical vegetable spills from around the world. In this study, specific behaviour tests were examined for several oils including canola, soy bean, olive, castor and corn oils. Evaporation, water-in-oil emulsification and chemical dispersion were measured and were found to be nearly zero, suggesting that vegetable oil spills are not very soluble in water. The aquatic toxicity of vegetable oil is low, but their fate is quite different from petroleum. Vegetable oils do not evaporate to a significant degree, they do not form water-in-oil emulsions, nor do they disperse in water. The physical properties of vegetable oils were also measured, including density and viscosity. This paper presented the aquatic toxicity of several vegetable oils along with other environmental data including the degradation rates noted in the literature. Most environmental damage reported in the literature is by contact with birds feathers resulting in hypothermia and secondly by smothering of intertidal organisms. The effect of vegetable oil on fish has not been well studied, but it is expected that there will be little destructive effect except where smothering can occur. 35 refs., 3 tabs.

Using wintergreen oil for mounting mosquito larvae: a safer alternative to xylene.

Science.gov (United States)

Koay, J B; Natasya, N N; Nashithatul, Mag; Ihsanuddin, R; Salleh, F M; Azil, A H

2016-01-01

Permanent mounting of fourth instar mosquito larvae is essential for identifying Aedes spp. This procedure requires extensive exposure to xylene, a clearing agent in the mounting process. We investigated wintergreen oil as a substitute for xylene. Five hundred larvae were mounted on slides to evaluate shrinkage or expansion of specimens after clearing using xylene or wintergreen oil. We examined the ventral brush and siphonal hair tufts for species identification and for preservation of morphological characteristics after clearing specimens in xylene or wintergreen oil. Shrinkage of the length of whole larvae and width of the head, thorax and abdomen after mounting was significantly greater after clearing with xylene than with wintergreen oil. The length of the comb scale nearest the ventral brush was similar for both clearing agents. The clarity of the specimens after mounting was improved by clearing with wintergreen oil, but the integrity of the ventral brush and siphonal hair tufts were similar for both clearing agents.

Fate of 14 C Labelled fungicides maneb and mancozeb during processing of contaminated soybean oil

International Nuclear Information System (INIS)

Zayed, S.M.A.D.; Hegazi, B.

1991-01-01

Soybeans from plants previously treated with 14 C-maneb and 14 C-mancozeb contain 0.62% and 3.15% of the applied dose, respectively. Crude soybean soil extracted from seeds was subjected to different refining processes. The effect of commercial refining processes, namely: alkali treatment, bleacking, winterization and deoderization on the nature and magnitude of the original residues was investigated. A high percentage of the residues was eliminated by alkali refining and deoderization processes. Analysis of residues after each step showed the ETU, ETM and ETD, in addition to two unknowns where the main 14 C-residues present in the oil. The refined oil contains around 1% of the residues originally present in the crude soybean oil.4 tab

Demulsification of residual waters from refining industries of lubricant oil: case study; Desemulsificacao de aguas residuarias de industrias de refino de oleo lubrificante: estudo de caso

Energy Technology Data Exchange (ETDEWEB)

Sawamura, Marcia Yumi; Morita, Dione Mari [Sao Paulo Univ., SP (Brazil). Escola Politecnica. Dept. de Engenharia Hidraulica e Sanitaria]. E-mail: dmmorita@usp.br

1997-07-01

The present work aims to evaluate the coagulation, flocculation with iron chloride (FeCl{sub 3}.6H{sub 2}O), followed by phase separation, as alternative for treating residual waters from lubricant oil refining industries. Tests have been performed by using {sup j}ar test{sup ,} changing pH value and coagulants for various wastewater characteristics.

Multiobjective clearing of reactive power market in deregulated power systems

International Nuclear Information System (INIS)

Rabiee, A.; Shayanfar, H.; Amjady, N.

2009-01-01

This paper presents a day-ahead reactive power market which is cleared in the form of multiobjective context. Total payment function (TPF) of generators, representing the payment paid to the generators for their reactive power compensation, is considered as the main objective function of reactive power market. Besides that, voltage security margin, overload index, and also voltage drop index are the other objective functions of the optimal power flow (OPF) problem to clear the reactive power market. A Multiobjective Mathematical Programming (MMP) formulation is implemented to solve the problem of reactive power market clearing using a fuzzy approach to choose the best compromise solution according to the specific preference among various non-dominated (pareto optimal) solutions. The effectiveness of the proposed method is examined based on the IEEE 24-bus reliability test system (IEEE 24-bus RTS). (author)

Energetic utilization of residues from wine-growing. Sewage plant Iphofen; Energetische Nutzung von Weinbaureststoffen. Klaeranlage Iphofen

Energy Technology Data Exchange (ETDEWEB)

Steinle, Eberhard; Carozzi, Alvaro [Dr.-Ing. Steinle Ingenieurgesellschaft fuer Abwassertechnik mbH, Weyarn (Germany); Mend, Josef; Kurth, Matthias [Stadt Iphofen (Germany)

2010-09-15

The treatment of waste water from the wine-growing and the treatment of liquid residual substances in local purification plants frequently result in a temporary overloading and disturbances. An innovative drop-off scheme was introduced at the purification plant Iphofen (Federal Republic of Germany). With this drop-off scheme, the winegrowers directly supply the highly concentrated liquid residual substances from the winemaking to the purification plant. There the residual substances can be used for the support of the denitrification and fermentation. After the successful conversion of this system, a gas utilization with small cogeneration units could be installed. Thus the resulting mass of gas will be used to the production of electricity and thermal energy. The authors of the contribution under consideration report on this system approach and on first operational experiences.

Time course of pulmonary burden in mice exposed to residual oil fly ash

Directory of Open Access Journals (Sweden)

Giovanna Marcella Cavalcante Carvalho

2014-09-01

Full Text Available Residual oil fly ash (ROFA is a common pollutant in areas where oil is burned. This particulate matter with a broad distribution of particle diameters can be inhaled by human beings and putatively damage their respiratory system. Although some studies deal with cultured cells, animals, and even epidemiological issues, so far a comprehensive analysis of respiratory outcomes as a function of the time elapsed after exposure to a low dose of ROFA is wanted. Thus, we aimed to investigate the time course of mechanical, histological, and inflammatory lung changes, as well as neutrophils in the blood, in mice exposed to ROFA until 5 days after exposure. BALB/c mice (25±5 g were randomly divided into 7 groups and intranasally instilled with either 10 µL of sterile saline solution (0.9% NaCl, CTRL or ROFA (0.2 µg in 10 L of saline solution. Pulmonary mechanics, histology (normal and collapsed alveoli, mononuclear and polymorphonuclear cells, and ultrastructure, neutrophils (in blood and bronchoalveolar lavage fluid were determined at 6 h in CTRL and at 6, 24, 48, 72, 96 and 120 h after ROFA exposure. ROFA contained metal elements, especially iron, polycyclic aromatic hydrocarbons, and organochlorines. Lung resistive pressure augmented early (6 h in the course of lung injury and other mechanical, histological and inflammatory parameters increased at 24 h, returning to control values at 120 h. Blood neutrophilia was present only at 24 and 48 h after exposure. Swelling of endothelial cells with adherent neutrophils was detected after ROFA instillation. No neutrophils were present in the lavage fluid. In conclusion, the exposure to ROFA, even in low doses, induced early changes in pulmonary mechanics, lung histology and accumulation of neutrophils in blood of mice that lasted for four days and disappeared spontaneously.

Time course of pulmonary burden in mice exposed to residual oil fly ash.

Science.gov (United States)

Carvalho, Giovanna Marcella Cavalcante; Nagato, Lilian Katiê da Silva; Fagundes, Sheila da Silva; Dos Santos, Flávia Brandão; Calheiros, Andrea Surrage; Malm, Olaf; Bozza, Patricia Torres; Saldiva, Paulo Hilário N; Faffe, Débora Souza; Rocco, Patricia Rieken Macedo; Zin, Walter Araujo

2014-01-01

Residual oil fly ash (ROFA) is a common pollutant in areas where oil is burned. This particulate matter (PM) with a broad distribution of particle diameters can be inhaled by human beings and putatively damage their respiratory system. Although some studies deal with cultured cells, animals, and even epidemiological issues, so far a comprehensive analysis of respiratory outcomes as a function of the time elapsed after exposure to a low dose of ROFA is wanted. Thus, we aimed to investigate the time course of mechanical, histological, and inflammatory lung changes, as well as neutrophils in the blood, in mice exposed to ROFA until 5 days after exposure. BALB/c mice (25 ± 5 g) were randomly divided into 7 groups and intranasally instilled with either 10 μL of sterile saline solution (0.9% NaCl, CTRL) or ROFA (0.2 μg in 10 μL of saline solution). Pulmonary mechanics, histology (normal and collapsed alveoli, mononuclear and polymorphonuclear cells, and ultrastructure), neutrophils (in blood and bronchoalveolar lavage fluid) were determined at 6 h in CTRL and at 6, 24, 48, 72, 96, and 120 h after ROFA exposure. ROFA contained metal elements, especially iron, polycyclic aromatic hydrocarbons (PAHs), and organochlorines. Lung resistive pressure augmented early (6 h) in the course of lung injury and other mechanical, histological and inflammatory parameters increased at 24 h, returning to control values at 120 h. Blood neutrophilia was present only at 24 and 48 h after exposure. Swelling of endothelial cells with adherent neutrophils was detected after ROFA instillation. No neutrophils were present in the lavage fluid. In conclusion, the exposure to ROFA, even in low doses, induced early changes in pulmonary mechanics, lung histology and accumulation of neutrophils in blood of mice that lasted for 4 days and disappeared spontaneously.

Spreading of oil from protein stabilised emulsions at air/water interfaces

NARCIS (Netherlands)

Schokker, E.P.; Bos, M.A.; Kuijpers, A.J.; Wijnen, M.E.; Walstra, P.

2002-01-01

Spreading of a drop of an emulsion made with milk proteins on air/water interfaces was studied. From an unheated emulsion, all oil molecules could spread onto the air/water interface, indicating that the protein layers around the oil globules in the emulsion droplet were not coherent enough to

Distilling hydrocarbon oils

Energy Technology Data Exchange (ETDEWEB)

Schulze, J E

1923-03-19

In distilling mineral oils such as petroleum, shale oil, distillates and topped or residual oils, particularly to obtain lubricating oils, the distillation is carried out under reduced pressures below an absolute pressure of 25 mm. of mercury and preferably below about 5 mm. of mercury, and the distillate is collected in fractions determined by the physical characteristics, such as viscosity, flash point, fire point, etc. Superheated steam may be passed through the liquid during distillation. A horizontal cylindrical still provided with cross braces and peripheral ribs interrupted at the base is connected through a condensing coil immersed in a steam chest and a baffled chamber with distillate receiver and is evacuated by a pump. Steam from a boiler and superheater is injected into the still through a perforated pipe. Steam and light oil vapors passing from the chamber are condensed in a coil.

Neuromuscular function during drop jumps in young and elderly males.

Science.gov (United States)

Piirainen, Jarmo M; Linnamo, Vesa; Sippola, Niina; Avela, Janne

2012-12-01

The Hoffman reflex (H-reflex), indicating alpha-motoneuron pool activity, has been shown to be task - and in resting conditions - age dependent. How aging affects H-reflex activity during explosive movements is not clear at present. The purpose of this study was to examine the effects of aging on H-reflexes during drop jumps, and its possible role in drop jump performance. Ten young (26.8 ± 2.7 years) and twenty elderly (64.2 ± 2.7 years) subjects participated in the study. Maximal drop jump performance and soleus H-reflex response (H/M jump) 20 ms after ground contact were measured in a sledge ergometer. Maximal H-reflex, maximal M-wave, Hmax/Mmax-ratio and H-reflex excitability curves were measured during standing rest. Although in young the H-reflex response (Hmax/Mmax) was 6.5% higher during relaxed standing and 19.7% higher during drop jumps (H jump/M jump) than in the elderly group, these differences were not statistically significant. In drop jumps, the elderly subjects had lower jumping height (30.4%, p push-off force (18.0%, p push-off time (31.0% p push-off force (r = 0.833, p push-off time (r = -0.857, p < 0.01) in young but not in the elderly. Correlations between H-reflex response and jumping parameters in young may indicate different jumping and activation strategies in drop jumps. However, it does not fully explain age related differences in jumping performance, since age related differences in H-reflex activity were non-significant. Copyright © 2012 Elsevier Ltd. All rights reserved.

Scaling crossover in thin-film drag dynamics of fluid drops in the Hele-Shaw cell

Science.gov (United States)

Okumura, Ko; Yahashi, Misato; Kimoto, Natsuki

2016-11-01

We study both experimentally and theoretically the descending motion due to gravity of a fluid drop surrounded by another immiscible fluid in a confined space between two parallel plates, i.e., in the Hele-Shaw cell. As a result, we show a new scaling regime of a nonlinear drag friction in viscous liquid that replaces the well-known Stokes' drag friction through a clear collapse of experimental data thanks to the scaling law. In the novel regime, the dissipation in the liquid thin film formed between the drop and cell walls governs the dynamics. The crossover of this scaling regime to another scaling regime in which the dissipation inside the droplet is dominant is clearly demonstrated and a phase diagram separating these scaling regimes is presented. To be published as, Y. Yahashi, N. Kimoto and K. Okumura, Scaling crossover in thin-film drag dynamics of fluid drops in the Hele-Shaw cell, Sci. Rep.(CC BY 4.0). This research was partly supported by ImPACT Program of Council for Science, Technology and Innovation (Cabinet Office, Government of Japan).

Effect of oil palm sustainability certification on deforestation and fire in Indonesia.

Science.gov (United States)

Carlson, Kimberly M; Heilmayr, Robert; Gibbs, Holly K; Noojipady, Praveen; Burns, David N; Morton, Douglas C; Walker, Nathalie F; Paoli, Gary D; Kremen, Claire

2018-01-02

Many major corporations and countries have made commitments to purchase or produce only "sustainable" palm oil, a commodity responsible for substantial tropical forest loss. Sustainability certification is the tool most used to fulfill these procurement policies, and around 20% of global palm oil production was certified by the Roundtable on Sustainable Palm Oil (RSPO) in 2017. However, the effect of certification on deforestation in oil palm plantations remains unclear. Here, we use a comprehensive dataset of RSPO-certified and noncertified oil palm plantations (∼188,000 km 2 ) in Indonesia, the leading producer of palm oil, as well as annual remotely sensed metrics of tree cover loss and fire occurrence, to evaluate the impact of certification on deforestation and fire from 2001 to 2015. While forest loss and fire continued after RSPO certification, certified palm oil was associated with reduced deforestation. Certification lowered deforestation by 33% from a counterfactual of 9.8 to 6.6% y -1 Nevertheless, most plantations contained little residual forest when they received certification. As a result, by 2015, certified areas held less than 1% of forests remaining within Indonesian oil palm plantations. Moreover, certification had no causal impact on forest loss in peatlands or active fire detection rates. Broader adoption of certification in forested regions, strict requirements to avoid all peat, and routine monitoring of clearly defined forest cover loss in certified and RSPO member-held plantations appear necessary if the RSPO is to yield conservation and climate benefits from reductions in tropical deforestation. Copyright © 2017 the Author(s). Published by PNAS.

Effect of oil palm sustainability certification on deforestation and fire in Indonesia

Science.gov (United States)

Gibbs, Holly K.; Noojipady, Praveen; Burns, David N.; Morton, Douglas C.; Walker, Nathalie F.; Paoli, Gary D.; Kremen, Claire

2018-01-01

Many major corporations and countries have made commitments to purchase or produce only “sustainable” palm oil, a commodity responsible for substantial tropical forest loss. Sustainability certification is the tool most used to fulfill these procurement policies, and around 20% of global palm oil production was certified by the Roundtable on Sustainable Palm Oil (RSPO) in 2017. However, the effect of certification on deforestation in oil palm plantations remains unclear. Here, we use a comprehensive dataset of RSPO-certified and noncertified oil palm plantations (∼188,000 km2) in Indonesia, the leading producer of palm oil, as well as annual remotely sensed metrics of tree cover loss and fire occurrence, to evaluate the impact of certification on deforestation and fire from 2001 to 2015. While forest loss and fire continued after RSPO certification, certified palm oil was associated with reduced deforestation. Certification lowered deforestation by 33% from a counterfactual of 9.8 to 6.6% y−1. Nevertheless, most plantations contained little residual forest when they received certification. As a result, by 2015, certified areas held less than 1% of forests remaining within Indonesian oil palm plantations. Moreover, certification had no causal impact on forest loss in peatlands or active fire detection rates. Broader adoption of certification in forested regions, strict requirements to avoid all peat, and routine monitoring of clearly defined forest cover loss in certified and RSPO member-held plantations appear necessary if the RSPO is to yield conservation and climate benefits from reductions in tropical deforestation. PMID:29229857

Behavior of 14C-BHC residues in rice grain

International Nuclear Information System (INIS)

Lee, S.R.; Kim, Y.H.

1981-01-01

γ-(U- 14 C)-BHC was applied to rice plants grown in a pot and its fate in the growth, polishing and oil-extraction processes of the grain was investigated. The 14 C-activity was absorbed and translocated widely in the plant and the recovery of applied 14 C-activity in the straw and grain was about 2.8%, of which 9.4% was found in the brown rice. The % partitioning of 14 C-residues in bran and polished rice was 12:88 and that in oil and oilcake was 37:63. Characterization of 14 C-residues the presence of γ-BHC, pentachlorocyclohexene, trichlorobenzene and hydrophilic metabolites, whose proportions were different in the straw and grain. (Author)

Combustion Characterization of Individual Bio-oil Droplets

DEFF Research Database (Denmark)

Hansen, Brian Brun; Jensen, Peter Arendt

2015-01-01

Single droplet combustion characteristics has been investigated for bio-oil slurries, containing biomass residue, and compared to conventional fuels for pulverized burners, such as fuel oil (start up) and wood chips (solid biomass fuel). The investigated fuels ignition delays and pyrolysis behavior...

Drop Calibration of Accelerometers for Shock Measurement

Science.gov (United States)

2011-08-01

important that the screen is clear, the records displayed are crisp and values are easily read. The current DSO, used within the Division, in the...Capacitor ≤ ± 0.01% ξc Tolerance of capacitor Drop Mass Reading ≤ ± 0.083 %  dm 0.1g over 120g (typically) Reference Mass Reading ≤ ± 0.1 % rm...Therefore m has uncertainty components due to rm ,  dm and ξrme. The random component is  222 dmrmm  (6.8) and once again  dsodc

Evaluation on sweep gas pressure drop in fusion blanket mock-up for in-pile test

International Nuclear Information System (INIS)

Ishitsuka, Etsuo; Kawamura, Hiroshi; Sagawa, Hisashi; Nagakura, Masaaki; Kanzawa, Toru.

1993-03-01

In the ITER/CDA (Conceptual Design Activity) of a tritium breeding blanket, Japan have proposed the pebble-typed blanket. The in-pile mock-up test will be preparing in JMTR (Japan Materials Testing Reactor) for Japanese engineering design with the pebble-typed blanket. Therefore, the He sweep gas pressure drop in the pebble bed was measured for the design of the mock-up used on in-pile test. From the results of this test, it was clear that the pressure drop was predicted on Kozeny- Carman's equation within +25 ∼ -60 %, and that the pressure drop was not affected by moisture concentration (< 100 ppm). (author)

Evaluation on sweep gas pressure drop in fusion blanket mock-up for in-pile test

Energy Technology Data Exchange (ETDEWEB)

Ishitsuka, Etsuo; Kawamura, Hiroshi; Sagawa, Hisashi (Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment); Nagakura, Masaaki; Kanzawa, Toru.

1993-03-01

In the ITER/CDA (Conceptual Design Activity) of a tritium breeding blanket, Japan have proposed the pebble-typed blanket. The in-pile mock-up test will be preparing in JMTR (Japan Materials Testing Reactor) for Japanese engineering design with the pebble-typed blanket. Therefore, the He sweep gas pressure drop in the pebble bed was measured for the design of the mock-up used on in-pile test. From the results of this test, it was clear that the pressure drop was predicted on Kozeny- Carman's equation within +25 [approx] -60 %, and that the pressure drop was not affected by moisture concentration (< 100 ppm). (author).

Evaluation on sweep gas pressure drop in fusion blanket mock-up for in-pile test

Energy Technology Data Exchange (ETDEWEB)

Ishitsuka, Etsuo; Kawamura, Hiroshi; Sagawa, Hisashi [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Nagakura, Masaaki; Kanzawa, Toru

1993-03-01

In the ITER/CDA (Conceptual Design Activity) of a tritium breeding blanket, Japan have proposed the pebble-typed blanket. The in-pile mock-up test will be preparing in JMTR (Japan Materials Testing Reactor) for Japanese engineering design with the pebble-typed blanket. Therefore, the He sweep gas pressure drop in the pebble bed was measured for the design of the mock-up used on in-pile test. From the results of this test, it was clear that the pressure drop was predicted on Kozeny- Carman`s equation within +25 {approx} -60 %, and that the pressure drop was not affected by moisture concentration (< 100 ppm). (author).

Evaporation of a liquid drop on a hot liquid surface, (1)

International Nuclear Information System (INIS)

Iida, Yoshihiro; Takashima, Takeo

1980-01-01

As for the phenomena occurring when two kinds of liquid at different temperature come in contact, the clarification of the basic, general matters of the phenomena has not been made yet. Such situation has been caused by the facts that the detailed observation of the aspect in liquid-liquid contact becomes impossible as the disturbance on the interface becomes violent, and it is difficult to obtain the quantitative data and to change temperature difference largely in practice. In this study, liquid drops were dropped on the free surface of another liquid at the temperature higher than the saturation temperature of the dropping liquid, and it was attempted to obtain the basic knowledge concerning the general behavior at the time of liquid-liquid contact by determining the aspect of evaporation and its change and evaporation time. For this experiment, the silicone oil with four different kinematic viscosity was used as the high temperature liquid, and n-pentane and dichloromethane soluble in the mother liquid, and acetone and methyl alcohol insoluble in the mother liquid were used as the liquid drops. The experimental apparatuses and method and the results are reported. The evaporation time curves presented lying S-shape basically, similarly to the evaporation on solid surfaces. The point of maximum evaporation time and the point of maximum heat transfer rate existed. (J.P.N.)

Characterization of Petroleum Hydrocarbons in Post-Burn Crude Oil ...

African Journals Online (AJOL)

In the Niger delta, crude oil spilled soils are burned as a means of decontaminating the impacted soils. Gas chromatography - flame ionization detector (GCFID) analyses were performed on oil residues extracted from burnt spilled oil soil samples to facilitate detailed chemical composition and characterization of petroleum ...

Decarboxylation Of Palm And Groundnut Oils In Medium Uv ...

African Journals Online (AJOL)

denise

INTRODUCTION. Vegetable oils undergo appreciable deterioration during processing and storage. The residual free fatty acid (FFA) concentration of vegetable oils is a function of the processing and storage conditions. Vegetable oils spoilage, usually defined as rancidity, is the result of fatty acid moity has been recognized ...

On the economics of the Russian oil sector

International Nuclear Information System (INIS)

Khartukov, E. M.

1996-01-01

The effects of political changes in the 1990s, particularly the hasty privatization of the oil industry, the all-out price liberalization and the radical transformation of the oil sector's taxation regime in Russia were examined. Details of the various tax regimes - excise duties on crude oil (introduced in 1992), contributions for mineral reserves replacement (1993), royalties on extracted and exported hydrocarbons (1992), investment fund deductions (1992, repealed in 1994), and the general tax on profits, introduced at 32 per cent in 1992, raised to 38 per cent in 1994,- were provided. As a result of this multitude of taxes, this core sector of Russia's economy has turned into the main tax-paying, but hardly profitable, business. It survives on marginal, and at times even negative, after-tax returns. According to official taxation data, in 1994 the after-tax profitability of the country's oil producing industry dropped to seven per cent, compared to 50 per cent enjoyed by Russian crude producers at the beginning of 1992. Downstream refinery margins have been equally low. Since the beginning of liberalization they have rarely exceeded five per cent and often dropped to one per cent. In an effort to save the industry, the government finally provided tax relief by removing export duties for Russian oil products effective December 1, 1995

Soviet Union oil sector outlook grows bleaker still

International Nuclear Information System (INIS)

Anon.

1991-01-01

This paper reports on the outlook for the U.S.S.R's oil sector which grows increasingly bleak and with it prospects for the Soviet economy. Plunging Soviet oil production and exports have analysts revising near term oil price outlooks, referring to the Soviet oil sector's self-destructing and Soviet oil production in a freefall. County NatWest, Washington, citing likely drops in Soviet oil production and exports (OGJ, Aug. 5, p. 16), has jumped its projected second half spot price for West Texas intermediate crude by about $2 to $22-23/bbl. Smith Barney, New York, forecasts WTI postings at $24-25/bbl this winter, largely because of seasonally strong world oil demand and the continued collapse in Soviet oil production. It estimates the call on oil from the Organization of Petroleum Exporting Countries at more than 25 million b/d in first quarter 1992. That would be the highest level of demand for OPEC oil since 1980, Smith Barney noted

An estimation of cogeneration potential by using refinery residuals in Mexico

International Nuclear Information System (INIS)

Marin-Sanchez, J.E.; Rodriguez-Toral, M.A.

2007-01-01

Electric power generation in Mexico is mainly based on fossil fuels, specifically heavy fuel oil, although the use of natural gas combined cycles (NGCC) is becoming increasingly important. This is the main destination that has promoted growing imports of natural gas, currently accounting for about 20% of the total national annual consumption. Available crude oil is becoming heavier; thus refineries should be able to process it, and to handle greater quantities of refinery residuals. If all refinery residuals are used in cogeneration plants serving petroleum refineries, the high heat/power ratio of refinery needs, leads to the availability of appreciable quantities of electricity that can be exported to the public utility. Thus, in a global perspective, Mexican imports of natural gas may be reduced by cogeneration using refinery residuals. This is not the authors' idea; in fact, PEMEX, the national oil company, has been entitled by the Mexican congress to sell its power leftovers to The Federal Electricity Commission (CFE) in order to use cogeneration in the way described for the years to come. A systematic way of determining the cogeneration potential by using refinery residuals from Mexican refineries is presented here, taking into account residual quantities and composition, from a national perspective, considering expected scenarios for Maya crude content going to local refineries in the years to come. Among different available technologies for cogeneration using refinery residuals, it is believed that the integrated gasification combined cycle (IGCC) would be the best option. Thus, considering IGCC plants supplying heat and power to refineries where it is projected to have refinery residuals for cogeneration, the expected electric power that can be sent to the public utility is quantified, along with the natural gas imports mitigation that may be attained. This in turn would contribute to a necessary fuel diversification policy balancing energy, economy and

Yields from pyrolysis of refinery residue using a batch process

Directory of Open Access Journals (Sweden)

S. Prithiraj

2017-12-01

Full Text Available Batch pyrolysis was a valuable process of assessing the potential of recovering and characterising products from hazardous waste materials. This research explored the pyrolysis of hydrocarbon-rich refinery residue, from crude oil processes, in a 1200 L electrically-heated batch retort. Furthermore, the off-gases produced were easily processed in compliance with existing regulatory emission standards. The methodology offers a novel, cost-effective and environmentally compliant method of assessing recovery potential of valuable products. The pyrolysis experiments yielded significant oil (70% with high calorific value (40 MJ/kg, char (14% with carbon content over 80% and non-condensable gas (6% with significant calorific value (240 kJ/mol. The final gas stream was subjected to an oxidative clean-up process with continuous on-line monitoring demonstrating compliance with South African emission standards. The gas treatment was overall economically optimal as only a smaller portion of the original residue was subjected to emission-controlling steps. Keywords: Batch pyrolysis, Volatiles, Oil yields, Char, Emissions, Oil recovery

Effect of textured eye drop bottles on the photostability of pranoprofen 0.1% ophthalmic solution.

Science.gov (United States)

Iwatsuka, Kinya; Inada, Katsuhiro; Ueoka, Hiroki; Otsuka, Tadashi; Maeda, Masaki; Yamaguchi, Masazumi; Yasueda, Shin-ichi

2015-01-01

Ophthalmic solutions are usually filled in a plastic bottle due to its durability and disposability. In Japan, photostability is one of the concerns for the quality control because an eye drop bottle must be a transparent container. The present work studied the effect of textured eye drop bottles on its light blocking to improve the photostability of ophthalmic solutions. We investigated the photostability of Pranoprofen ophthalmic solution filled in a variety of textured eye drop bottles. Pranoprofen content was analyzed by high-performance liquid chromatography and surface structure of textured eye drop bottles was evaluated by transmittance, calculated average roughness (Ra) and haze intensity. We observed that eye drop bottle which had greater than Ra value of 1.0 µm and haze intensity 62% clearly showed photostability improvement. This report is the first one which shows that photostability of ophthalmic solution is improved by using textured eye drop bottle. Moreover, this approach is a simple and effective method to improve the photostability. This method is available for not only various ophthalmic applications but also other liquid pharmaceuticals or food products.

Chemical aspects of shale and shale oils

Energy Technology Data Exchange (ETDEWEB)

Hackford, J E

1922-01-01

To prove that the kerogen in oil shale is a form of bitumen, several experiments were made with oil shale and a heavy asphaltic oil mixed with fuller's earth. When distilled, both the oil shale and asphalt-impregnated fuller's earth yielded paraffin oil, wax, and hydrogen sulfide (if sulfur was present). Both yielded ammonia if nitrogen was present. The organic material in each was partly isolated by extraction with pyridine and appeared to be the same. Oil shale is a marl that was saturated with oil or through which oil has passed or filtered. The insolubilities of its organic compounds are due to a slightly elevated temperature for a prolonged period and to the retaining effect exerted by the finely divided marl. The marl exerted a selective action on the oil and absorbed the asphaltum, sulfur, and nitrogen compounds from the oil. The class of oil evolved from a shale depended on the nature of the original compounds absorbed. Asphaltenes obtained from crude oil by precipitation with ethyl ether produced distillation products of water, hydrogen sulfide, ammonia, oil, wax, and a carbonaceous residue. Water was formed by decomposition of oxyasphaltenes and hydrogen sulfide by decomposition of thioasphaltenes. Ammonia was evolved during decomposition if lime was present, but if there was not sufficient free lime present, pyridine and pyrrole derivatives were redistilled as such. The oil and wax that resulted from the dry distillation were true decomposition products and equaled about 60 weight-percent of the asphaltenes. The oil and wax content of the mixture varied between 8 and 10 percent. The carbonaceous residue, which represented approximately 40 percent of the original asphaltene, was a decomposition product of the asphaltenes. Geologic comparisons of oil-shale deposits and oil-well fields were also made.

[Optimize dropping process of Ginkgo biloba dropping pills by using design space approach].

Science.gov (United States)

Shen, Ji-Chen; Wang, Qing-Qing; Chen, An; Pan, Fang-Lai; Gong, Xing-Chu; Qu, Hai-Bin

2017-07-01

In this paper, a design space approach was applied to optimize the dropping process of Ginkgo biloba dropping pills. Firstly, potential critical process parameters and potential process critical quality attributes were determined through literature research and pre-experiments. Secondly, experiments were carried out according to Box-Behnken design. Then the critical process parameters and critical quality attributes were determined based on the experimental results. Thirdly, second-order polynomial models were used to describe the quantitative relationships between critical process parameters and critical quality attributes. Finally, a probability-based design space was calculated and verified. The verification results showed that efficient production of Ginkgo biloba dropping pills can be guaranteed by operating within the design space parameters. The recommended operation ranges for the critical dropping process parameters of Ginkgo biloba dropping pills were as follows: dropping distance of 5.5-6.7 cm, and dropping speed of 59-60 drops per minute, providing a reference for industrial production of Ginkgo biloba dropping pills. Copyright© by the Chinese Pharmaceutical Association.

The Newfoundland oil spill burn experiment

International Nuclear Information System (INIS)

Fingas, M.

1992-01-01

A major offshore oil-spill combustion experiment is being planned for waters off Newfoundland. The experiment is designed to answer outstanding questions on the acceptability of in-situ oil spill burning. In the experiment, variables will be controlled to allow quantitative measurement of the scientific and operational parameters that will enhance understanding of in-situ combustion as an operational oil-spill response technique. The proposed full-scale tests follow six years of testing in laboratory tanks. Analyses have shown that the high temperatures reached during efficient in-situ combustion result in relatively complete destruction of the oil. Tests have shown that the most important factor in this regard is that the oil must be thickened sufficiently before effective burning will occur. Such thickening is potentially possible in the offshore, under suitable wind and sea conditions, using fireproof containment booms. The experiment will involve measurement of emissions to the air, levels of oil in water, and operational parameters of in-situ burning. Time and location of the experiment are chosen to minimize ecological damage and for operational reasons. When suitable conditions are present in early August 1993, two 45-m 3 batches of crude oil will be released into a containment boom and ignited. The burn residue will be recovered mechanically, and a secondary containment and recovery system will be towed behind the fireproof boom to pick up any fugitive oil or residue. 3 figs., 6 tabs

75 FR 40751 - Castor Oil, Ethoxylated, Oleate; Tolerance Exemption

Science.gov (United States)

2010-07-14

... ENVIRONMENTAL PROTECTION AGENCY 40 CFR Part 180 [EPA-HQ-OPP-2010-0231; FRL-8834-4] Castor Oil... castor oil, ethoxylated, oleate (CAS Reg. No. 220037-02-5) with a minimum number average molecular weight... regulation eliminates the need to establish a maximum permissible level for residues of castor oil...

Lambda-dropping

DEFF Research Database (Denmark)

Danvy, Olivier; Schultz, Ulrik Pagh

1997-01-01

Lambda-lifting a functional program transforms it into a set of recursive equations. We present the symmetric transformation: lambda-dropping. Lambda-dropping a set of recursive equations restores block structure and lexical scope.For lack of scope, recursive equations must carry around all...... the parameters that any of their callees might possibly need. Both lambda-lifting and lambda-dropping thus require one to compute a transitive closure over the call graph:• for lambda-lifting: to establish the Def/Use path of each free variable (these free variables are then added as parameters to each...... of the functions in the call path);• for lambda-dropping: to establish the Def/Use path of each parameter (parameters whose use occurs in the same scope as their definition do not need to be passed along in the call path).Without free variables, a program is scope-insensitive. Its blocks are then free...

The Galeta Oil Spill. II. Unexpected Persistence of Oil Trapped in Mangrove Sediments

Science.gov (United States)

Burns, K. A.; Garrity, S. D.; Jorissen, D.; MacPherson, J.; Stoelting, M.; Tierney, J.; Yelle-Simmons, L.

1994-04-01

Sediment chemistry studies, undertaken as part of the long-term assessment of the Bahía las Minas (Panamá) oil spill, showed the unexpected persistence of the full range of aromatic hydrocarbon residues of the spilled crude oil in anoxic muds of coastal mangroves. Mangrove muds served as long-term reservoirs for chronic contamination of contiguous coastal communities for over 5 years. One result of the repeated history of oil pollution incidents along this coast was an increased proportion of dead mangrove ( Rhizophora mangle) roots in sediment cores which was related to contaminant loading and was detectable for at least 20 years after major oil spills. We suggest that this is the minimum time-scale that is to be expected for the loss of toxicity of oil trapped in muddy coastal habitats impacted by catastrophic oil spills.

Mineral oils, tars. [British patent

Energy Technology Data Exchange (ETDEWEB)

O' Brien, A M; Handmarch, E

1933-08-11

Hydrocarbon materials such as mineral oils and tars from coal, shale, lignite, or peat are freed from phenols and like oxy-bodies by heating under pressure in a closed vessel to a temperature and for a time sufficient to effect reduction of the oxy-bodies, and then removing the water formed by the reaction. 350/sup 0/ to 400/sup 0/C. for 30 to 60 minutes is suitable. Any wax-like constituents are converted to liquids of lower viscosity and settling point. The product may be fractionated to give light oils and a residue of aviation Diesel fuel. In an example, oil from the low-temperature distillation of coal and having a tar acid content of 30 per cent is treated in a tubular converter at 380/sup 0/C. and 400 lb. per sq. in for 40 min., and the benzine toluol, and xylol distilled; the residue has a tar acid content of only 7.6 per cent.

Drop weld thermal injuries to the middle ear.

LENUS (Irish Health Repository)

Keogh, I J

2009-01-01

Drop weld injuries to the tympanic membrane and middle ear caused by hot sparks or molten slag are a rare but significant injury. Steel workers and welders who are regularly exposed to flying sparks and molten metal slag are predisposed. This type of transtympanic thermal injury occurs when the slag literally drops into the external auditory canal and burns through the tympanic membrane. A spectrum of severity of injury occurs which includes chronic tympanic membrane perforation, chronic otorrhoea, facial nerve injury and deafness. Chronic tympanic membrane perforation is the most common sequelae and is perhaps one of the most challenging of all perforations to repair The combination of direct thermal injury and foreign body reaction results in continuing or recurrent suppuration. The foreign body reaction is due to the embedding of metal slag in the promontorial mucosa. We present a case of drop weld injury to the left tympanic membrane, resulting in chronic middle ear inflammation, otorrhoea and tympanic perforation. CAT scan clearly demonstrated a metallic promontorial foreign body with localised bone erosion. We emphasise the importance of removing these foreign bodies and recommend a cartilage reinforced underlay tympanoplasty technique to repair these perforations. Transtympanic thermal trauma is a preventable occupational injury, which is best, avoided by earplugs and increased awareness.

Management of NORM Residues

International Nuclear Information System (INIS)

2013-06-01

The IAEA attaches great importance to the dissemination of information that can assist Member States in the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support the nuclear fuel cycle and nuclear applications, and that address the legacy of past practices and accidents. However, radioactive residues are found not only in nuclear fuel cycle activities, but also in a range of other industrial activities, including: - Mining and milling of metalliferous and non-metallic ores; - Production of non-nuclear fuels, including coal, oil and gas; - Extraction and purification of water (e.g. in the generation of geothermal energy, as drinking and industrial process water; in paper and pulp manufacturing processes); - Production of industrial minerals, including phosphate, clay and building materials; - Use of radionuclides, such as thorium, for properties other than their radioactivity. Naturally occurring radioactive material (NORM) may lead to exposures at some stage of these processes and in the use or reuse of products, residues or wastes. Several IAEA publications address NORM issues with a special focus on some of the more relevant industrial operations. This publication attempts to provide guidance on managing residues arising from different NORM type industries, and on pertinent residue management strategies and technologies, to help Member States gain perspectives on the management of NORM residues

Natural oils and waxes: studies on stick bases.

Science.gov (United States)

Budai, Lívia; Antal, István; Klebovich, Imre; Budai, Marianna

2012-01-01

The objective of the present article was to examine the role of origin and quantity of selected natural oils and waxes in the determination of the thermal properties and hardness of stick bases. The natural oils and waxes selected for the study were sunflower, castor, jojoba, and coconut oils. The selected waxes were yellow beeswax, candelilla wax, and carnauba wax. The hardness of the formulations is a critical parameter from the aspect of their application. Hardness was characterized by the measurement of compression strength along with the softening point, the drop point, and differential scanning calorimetry (DSC). It can be concluded that coconut oil, jojoba oil, and carnauba wax have the greatest influence on the thermal parameters of stick bases.

Design of a process for the use of residual hydrocarbons coming from the ships arriving at Moin for obtaining of a fuel

International Nuclear Information System (INIS)

Madrigal Calderon, Adolfo

2015-01-01

A process is designed to carry out the obtaining of a fuel from the residual mixture of residual oils coming from the ships arriving at Moin, Limon, Costa Rica . A sampling of the residual oil in different ships is realized for a month to quantify the water content and basic sediment, as well as the heavy metal content. The results obtained have been 20,4 ± 4,6 % v/v of water and sediment, and 6,939 ppm of heavy metals as a minimum, this value may be higher depending on the quality of lubricant. The production volume of the residual oil is estimated according to historical data of the company ACASE S.A. (company responsible for collecting the oil residue of ships arriving at dock of Moin, Limon); therefore, the plant must process 25,000 liters of dirty oil per day. The main technologies (thermal process, treatment with chemical reaction, vacuum distillation and solvent extraction) to perform the process are compared and studied through a selection matrix. The technical and economic parameters chosen for the matrix have been: environmental impact, cost of operation, cost of equipment, safety of operation, maintenance of equipment, by-products obtained, waste generated, quality of the product obtained and ease of operation. The study has concluded that the treatment with chemical reaction has been the best option for the project of used oil utilization, as well as other physical methods of cleaning as the centrifugation of the same one. The installation of a waste oil processing plant has been a project that environmentally represents a benefit and economically viable, as currently the residual oil is left untreated for later use [es

Enhanced oil recovery from Sandstones and Carbonates with “Smart Water”

OpenAIRE

Torrijos, Ivan Dario Pinerez

2017-01-01

PhD thesis in Petroleum engineering According to the International Energy Agency crude oil is expected to contribute approximately with 26% of the world’s energy supply by 2040. In a per year basis, new oil discoveries have dropped to a 60-year low in 2015, and capital expenditure is in the longest period of retrenchment in 40 years. Therefore, oil in place from already discovered reservoirs has become an important target for oil companies. “Smart Water” injection is a relatively new E...

What remains of the Arrow oil?

International Nuclear Information System (INIS)

Sergy, G.; Owens, E.

1993-01-01

In February 1970, the tanker Arrow became grounded 6.5 km off the north shore of Chedabucto Bay, Nova Scotia, and nearly 72,000 bbl of Bunker C fuel oil were released from the vessel during its subsequent breakup and sinking. The oil was washed ashore in various degrees over an estimated 305 km of the bay's 604-km shoreline, of which only 48 km were cleaned. In addition, the tanker Kurdistan broke in two in pack ice in March 1979 in the Cabot Strait area, spilling ca 54,000 bbl of Bunker C, some of which was later found at 16 locations along the northeast and east shorelines of Chedabucto Bay. In summer 1992, a systematic ground survey of the bay's shorelines was conducted using Environment Canada Shoreline Cleanup Assessment Team (SCAT) procedures. Standard observations were made of oil distribution and width, thickness, and character of the oil residues in 419 coastal segments. Results from the survey are summarized. Oil was found to be present on 13.3 km of the shoreline, with heavy oiling restricted to 1.3 km primarily in the areas of Black Duck Cove and Lennox Passage. Some of this residual oil was identified as coming from the Arrow. Natural weathering processes account for removal of most of the spilled oil from the bay. Oil remaining on the shore was found in areas outside of the zone of physical wave action, in areas of nearshore mixing where fine sediments are not present to weather the oil through biophysical processes, or in crusts formed by oil weathered on the surface. The systematic description of oiled shorelines using the SCAT methodology proved very successful, even for such an old spill. 6 refs

The H-Oil process: a worldwide leader in vacuum residue hydro processing

Energy Technology Data Exchange (ETDEWEB)

Colyar, J.J.; Wisdom, L.I.; Koskas, A.

1996-12-31

The h-Oil process is a catalytic hydrocracking process which is used to convert and upgrade petroleum residua and heavy oils. This paper discusses additional background information on the H-Oil process, some of the key advances made to the process and applications for the Latin America market. 5 refs., 6 tabs.., 2 figs.

New technology for the emulsification of petroleum residuals in water; Nueva tecnologia para la emulsificacion de residuales del petroleo en agua

Energy Technology Data Exchange (ETDEWEB)

Peralta, M. Vita; Arriola, Alejandro M.; Sanchez S, Ramon; Manzanares P, Emilio; Romo M, Cesar A.; Yery de Coss P, R. [Instituto de Investigaciones Electricas, Temixco, Morelos (Mexico)

2001-07-01

It turns out of interest to Comision Federal de Electricidad and Petroleos Mexicanos to reduce costs of fuel oil, reducing the viscosity of the residues petroleum of high vacuum distillation emulsifying these with water. The parameters that define the characteristics of the emulsions are mainly the relation of their components, viscosity, size and drop distribution and its stability. The experimental work began producing emulsions in form of lots, using samples of approximately 500 milliliters of vacuum residue. In this first stage, at different concentrations, were examined eight different surfactants, as well as combinations among them, also seven different stabilizers were used. With these tests it has been managed to identify the concentrations, as well as the most adequate relations of surfactants and stabilizers for the production of emulsions of vacuum residues in water. The size and drop distribution has been determined by means of an optical LEICA microscope, model DMLS, that has adapted a photographic system in which an emulsion photo is obtained and, later, a system of analysis of images is used for obtaining of the values of the diameter of the drops present in the emulsion. Finally, by means of statistical software the average size of the particles is obtained, as well as the drop size distribution. The tests results of emulsions that remain fluid are shown and an example of the microstructure of an emulsion of vacuum residue-in-water is given. As well as an example of histogram of the drop size distribution of an emulsion of vacuum distillation-in-water, and another one of the viscosity in function of temperature at different cut efforts in one emulsion of vacuum distillate residue-in-water. [Spanish] Resulta de interes para la Comision Federal de Electricidad y Petroleos Mexicanos reducir costos del combustoleo, reduciendo la viscosidad de los residuos de vacio emulsionando estos en agua. Los parametros que definen las caracteristicas de las

Oil mixing behavior after an oil spill: identification conflicts of different fingerprints.

Science.gov (United States)

He, Shijie; Yu, Hongjun; Luo, Yongming; Wang, Chuanyuan; Li, Xueshuang; Li, Zhongping

2018-04-01

Clearing up whether spilled oil is mixed or not can strengthen the accuracy of oil spill identification. In the present study, the biomarkers in spilled oil samples were detected. The weathering modes of different types of diagnostic ratio and carbon isotope values of individual n-alkanes were also analyzed. The results showed that the diagnostic ratios of steroids, terpenes and aromatics, and weathering characteristics of carbon isotope composition (δ 13 C) of individual n-alkanes supported the idea that Dalian oil spill emerged from a single oil source. Furthermore, commonly used diagnostic ratios of n-alkanes indicated that the Dalian oil spill had undergone the oil mixing process. The different identifying outcomes indicate that some kinds of n-alkane-rich substance (such as oil dispersants) were mixed in the Dalian spilled oil and interfered with the routine diagnosis ratios of n-alkanes.

Cheap oil benefits coal on the short term, not the long

Energy Technology Data Exchange (ETDEWEB)

Soras, C.G.; Stodden, J.R.

1986-03-01

This is a brief article describing the effects of the declining price of oil on the coal industry. The oil price explosion from 1973-1979 is described along with the present day situation. Oil consumption in the US and the general drop in production worldwide is represented. It is concluded that the coal industry will benefit in the short term from the present crisis but stands to make some losses in the long run.

Giant Oil Fields - The Highway to Oil: Giant Oil Fields and their Importance for Future Oil Production

International Nuclear Information System (INIS)

Robelius, Fredrik

2007-01-01

Since the 1950s, oil has been the dominant source of energy in the world. The cheap supply of oil has been the engine for economic growth in the western world. Since future oil demand is expected to increase, the question to what extent future production will be available is important. The belief in a soon peak production of oil is fueled by increasing oil prices. However, the reliability of the oil price as a single parameter can be questioned, as earlier times of high prices have occurred without having anything to do with a lack of oil. Instead, giant oil fields, the largest oil fields in the world, can be used as a parameter. A giant oil field contains at least 500 million barrels of recoverable oil. Only 507, or 1 % of the total number of fields, are giants. Their contribution is striking: over 60 % of the 2005 production and about 65 % of the global ultimate recoverable reserve (URR). However, giant fields are something of the past since a majority of the largest giant fields are over 50 years old and the discovery trend of less giant fields with smaller volumes is clear. A large number of the largest giant fields are found in the countries surrounding the Persian Gulf. The domination of giant fields in global oil production confirms a concept where they govern future production. A model, based on past annual production and URR, has been developed to forecast future production from giant fields. The results, in combination with forecasts on new field developments, heavy oil and oil sand, are used to predict future oil production. In all scenarios, peak oil occurs at about the same time as the giant fields peak. The worst-case scenario sees a peak in 2008 and the best-case scenario, following a 1.4 % demand growth, peaks in 2018

Planning logistics operations in the oil industry

International Nuclear Information System (INIS)

Dempster, M.A.H.; Hicks Pedron, N.; Medova, E.A.; Scott, J.E.; Sembos, A.

2000-01-01

In this paper we apply stochastic programming modelling and solution techniques to planning problems for a consortium of oil companies. A multiperiod supply, transformation and distribution scheduling problem - the Depot and Refinery Optimization Problem (DROP) - is formulated for strategic or tactical level planning of the consortium's activities. This deterministic model is used as a basis for implementing a stochastic programming formulation with uncertainty in the product demands and spot supply costs (DROPS), whose solution process utilizes the deterministic equivalent linear programming problem. We employ our STOCHGEN general purpose stochastic problem generator to 'recreate' the decision (scenario) tree for the unfolding future as this deterministic equivalent. To project random demands for oil products at different spatial locations into the future and to generate random fluctuations in their future prices/costs a stochastic input data simulator is developed and calibrated to historical industry data. The models are written in the modelling language XPRESS-MP and solved by the XPRESS suite of linear programming solvers. From the viewpoint of implementation of large-scale stochastic programming models this study involves decisions in both space and time and careful revision of the original deterministic formulation. The first part of the paper treats the specification, generation and solution of the deterministic DROP model. The stochastic version of the model (DROPS) and its implementation are studied in detail in the second part and a number of related research questions and implications discussed. (author)

Raman detection of extra virgin olive oil adulterated with cheaper oils

Science.gov (United States)

Farley, Carlton; Kassu, Aschalew; Mills, Jonathan; Kenney, Brianna; Ruffin, Paul; Sharma, Anup

2016-09-01

Pure extra virgin olive oil (EVOO) is mixed with cheaper edible oils and samples are kept inside clear glass containers, while a 785nm Raman system is used to take measurements as Raman probe is placed against glass container. Several types of oils at various concentrations of adulteration are used. Ratios of peak intensities are used to analyze raw data, which allows for quick, easy, and accurate analysis. While conventional Raman measurements of EVOO may take as long as 2 minutes, all measurements reported here are for integration times of 15s. It is found that adulteration of EVOO with cheaper oils is detectable at concentrations as low as 5% for all oils used in this study.

Leveraging microbial biosynthetic pathways for the generation of 'drop-in' biofuels.

Science.gov (United States)

Zargar, Amin; Bailey, Constance B; Haushalter, Robert W; Eiben, Christopher B; Katz, Leonard; Keasling, Jay D

2017-06-01

Advances in retooling microorganisms have enabled bioproduction of 'drop-in' biofuels, fuels that are compatible with existing spark-ignition, compression-ignition, and gas-turbine engines. As the majority of petroleum consumption in the United States consists of gasoline (47%), diesel fuel and heating oil (21%), and jet fuel (8%), 'drop-in' biofuels that replace these petrochemical sources are particularly attractive. In this review, we discuss the application of aldehyde decarbonylases to produce gasoline substitutes from fatty acid products, a recently crystallized reductase that could hydrogenate jet fuel precursors from terpene synthases, and the exquisite control of polyketide synthases to produce biofuels with desired physical properties (e.g., lower freezing points). With our increased understanding of biosynthetic logic of metabolic pathways, we discuss the unique advantages of fatty acid, terpene, and polyketide synthases for the production of bio-based gasoline, diesel and jet fuel. Copyright © 2017 Elsevier Ltd. All rights reserved.

A case study on fuel oil contamination in a mangrove swamp in Hong Kong

Energy Technology Data Exchange (ETDEWEB)

Tam, N.F.Y.; Wong, T.W.Y.; Wong, Y.S. [City University of Hong Kong, Kowloon (Hong Kong). Department of Biology

2005-07-01

Mangroves commonly found along tropical and subtropical coastlines are susceptible to oil pollution. In December 2000, around 500 1 m tall Kandelia candel saplings at the age of 3-5 years old located at the foreshore region of Sheung Pak Nai swamp, Hong Kong SAR, were found to be damaged by oil pollution. More than 80% of the saplings were either dead or washed away and leaving less than 5% healthy saplings with dense green leaves. Elevated concentrations of light n-alkanes (ranging from n-C{sub 14} to n-C{sub 20}), pristane and phytane were recorded in surface sediments collected in December 2000. The ratio between light and total n-alkanes was 0.4. The total petroleum hydrocarbons (60-80 {mu}g g{sup -1} TPH) and unresolved complex mixtures (60-70 {mu}g g{sup -1} UCM) were higher than the background values of other mangrove sediments in Hong Kong, which were 40 and 20 {mu}g g{sup -1}, respectively. In certain root zone sediments, TPH concentrations were above 1000 {mu}g g{sup -1}. These results suggest that surface sediments in Sheung Pak Nai were contaminated by petroleum oil, most likely by illegal discharge of fuel oil which occurred between 1998 and 2002. One year later, in December 2001, unhealthy saplings had recovered and re-grown. The concentrations of TPH and UCM in sediments declined to around 40 {mu}g g{sup -1}, pristane and phytane dropped by 80%, and the ratio of light to total n-alkanes was 0.15, suggesting that residual oil in sediments was weathered leading to a remarkable recovery of the unhealthy saplings. (author)

Effects of cooking and storage on residues of cyadox in chicken muscle.

Science.gov (United States)

Zhang, Yanling; Wang, Yulian; Huang, Lingli; Chen, Dongmei; Tao, Yanfei; Yuan, Zonghui

2005-12-14

The aim of this study was to investigate the depletion of residues of cyadox in chicken muscle over time. The heat stabilities of cyadox (CYX) and its two metabolites, 1,4-bisdesoxycyadox (BDCYX) and quinoxaline-2-carboxylic acid (QCA), in water, cooking oil, and as incurred residues in chicken muscle were investigated. CYX was shown to be unstable with a half-life of about 37.7 min in 100 degrees C water. In hot cooking oil at 180 degrees C, all three compounds were unstable. CYX decreased quickly and was not able to be detected after heating for 2 min. Diode-array analysis of CYX standard solution in cooking oil indicated that a portion of BDCYX was formed. The residues of CYX and BDCYX deteriorated rapidly in frozen storage, while that of QCA changed slowly. Muscles containing CYX residues were boiled, microwaved, or fried for the specified times. During boiling, CYX and BDCYX were reduced 94% and 81% in 10 min, respectively. During microwave cooking, CYX and BDCYX were reduced 54% and 47% in 2.5 min, respectively. During frying, CYX and BDCYX were reduced 86% and 76%, respectively. No significant reduction of QCA was found for the three cooking methods. The half-lives of CYX residues in cooked chicken muscles were estimated as follows: 2.22 min for CYX and 4.44 min for BDCYX by boiling; 6.66 min for CYX and 9.36 min for BDCYX by microwaving.

Storage stability of screwpress-extracted oils and residual meals from CELSS candidate oilseed crops

Science.gov (United States)

Stephens, S. D.; Watkins, B. A.; Nielsen, S. S.

1997-01-01

The efficacy of using screwpress extraction for oil was studied with three Controlled Ecological Life-Support System (CELSS) candidate oilseed crops (soybean, peanut, and canola), since use of volatile organic solvents for oil extraction likely would be impractical in a closed system. Low oil yields from initial work indicated that a modification of the process is necessary to increase extraction efficiency. The extracted oil from each crop was tested for stability and sensory characteristics. When stored at 23 degC, canola oil and meal were least stable to oxidative rancidity, whereas peanut oil and meal were least stable to hydrolytic rancidity. When stored at 65 degC, soybean oil and canola meal were least stable to oxidative rancidity, whereas peanut oil and meal were least stable to hydrolytic rancidity. Sensory evaluation of the extracted oils used in bread and salad dressing indicated that flavor, odor intensity, acceptability, and overall preference may be of concern for screwpress-extracted canola oil when it is used in an unrefined form. Overall results with screwpress-extracted crude oils indicated that soybean oil may be more stable and acceptable than canola or peanut under typical storage conditions.

Sensor and Methodology for Dielectric Analysis of Vegetal Oils Submitted to Thermal Stress

Directory of Open Access Journals (Sweden)

Sergio Luiz Stevan

2015-10-01

Full Text Available Vegetable oils used in frying food represent a social problem as its destination. The residual oil can be recycled and returned to the production line, as biodiesel, as soap, or as putty. The state of the residual oil is determined according to their physicochemical characteristics whose values define its economically viable destination. However, the physicochemical analysis requires high costs, time and general cost of transporting. This study presents the use of a capacitive sensor and a quick and inexpensive method to correlate the physicochemical variables to the dielectric constant of the material undergoing oil samples to thermal cycling. The proposed method allows reducing costs in the characterization of residual oil and the reduction in analysis time. In addition, the method allows an assessment of the quality of the vegetable oil during use. The experimental results show the increasing of the dielectric constant with the temperature, which facilitates measurement and classification of the dielectric constant at considerably higher temperatures. The results also confirm a definitive degradation in used oil and a correlation between the dielectric constant of the sample with the results of the physicochemical analysis (iodine value, acid value, viscosity and refractive index.

Sensor and methodology for dielectric analysis of vegetal oils submitted to thermal stress.

Science.gov (United States)

Stevan, Sergio Luiz; Paiter, Leandro; Galvão, José Ricardo; Roque, Daniely Vieira; Chaves, Eduardo Sidinei

2015-10-16

Vegetable oils used in frying food represent a social problem as its destination. The residual oil can be recycled and returned to the production line, as biodiesel, as soap, or as putty. The state of the residual oil is determined according to their physicochemical characteristics whose values define its economically viable destination. However, the physicochemical analysis requires high costs, time and general cost of transporting. This study presents the use of a capacitive sensor and a quick and inexpensive method to correlate the physicochemical variables to the dielectric constant of the material undergoing oil samples to thermal cycling. The proposed method allows reducing costs in the characterization of residual oil and the reduction in analysis time. In addition, the method allows an assessment of the quality of the vegetable oil during use. The experimental results show the increasing of the dielectric constant with the temperature, which facilitates measurement and classification of the dielectric constant at considerably higher temperatures. The results also confirm a definitive degradation in used oil and a correlation between the dielectric constant of the sample with the results of the physicochemical analysis (iodine value, acid value, viscosity and refractive index).

Controlling charge on levitating drops.

Science.gov (United States)

Hilger, Ryan T; Westphall, Michael S; Smith, Lloyd M

2007-08-01

Levitation technologies are used in containerless processing of materials, as microscale manipulators and reactors, and in the study of single drops and particles. Presented here is a method for controlling the amount and polarity of charge on a levitating drop. The method uses single-axis acoustic levitation to trap and levitate a single, initially neutral drop with a diameter between 400 microm and 2 mm. This drop is then charged in a controllable manner using discrete packets of charge in the form of charged drops produced by a piezoelectric drop-on-demand dispenser equipped with a charging electrode. The magnitude of the charge on the dispensed drops can be adjusted by varying the voltage applied to the charging electrode. The polarity of the charge on the added drops can be changed allowing removal of charge from the trapped drop (by neutralization) and polarity reversal. The maximum amount of added charge is limited by repulsion of like charges between the drops in the trap. This charging scheme can aid in micromanipulation and the study of charged drops and particles using levitation.

Bioremediation of Contaminated Soil with Oils Residuals through Bioaugmentation and Natural Attenuation

Directory of Open Access Journals (Sweden)

Maitê Carla Deon

2012-04-01

Full Text Available The potential for soil contamination by oil spills is growing, due to heavy industrialization and economic development of countries. Due to this fact, the bioremediation has become an alternative to remediate areas through the use of biological agents. Two microorganisms, isolated from a lipid-rich effluent, were used in the bioaugmentation of soils contaminated with diesel oil, lubricating oil and soybean oil. Natural attenuation tests were conducted as controls. The removal of diesel fuel at the time of 21 d were of 18.5%, 7.30% and 11.38%, respectively, for the bioaugmentation with isolated I1 and I2 and natural attenuation. The removal of lubricating oil were 41.6%, 14.16% and 6.91% respectively for the bioaugmentation with the isolated I1 and I2 and natural attenuation, while for soybean oil removals were of 87 8%, 73.9% and 49.4%. Considering the processes of bioaugmentatiom and natural attenuation, the bioaugmentation with the isolated I1 showed better results, possibly due to the production of compounds capable of reducing the surface tension during the preparation of bioaugmentation.

The Galeta oil spill: Pt. 2; Unexpected persistence of oil trapped in mangrove sediments

Energy Technology Data Exchange (ETDEWEB)

Burns, K.A.; Jorissen, D.; MacPherson, J.; Stoelting, M.; Tierney, J.; Yelle-Simmons, L. (Bermuda Biological Station, Ferry Reach (Bermuda)); Garrity, S.D. (Coastal Zone Analysis, Sopchoppy, FL (United States))

1994-04-01

Sediment chemistry studies, undertaken as part of the long-term assessment of the Bahia las Minas (Panama) oil spill, showed the unexpected persistence of the full range of aromatic hydrocarbon residues of the spilled crude oil in anoxic muds of coastal mangroves. Mangrove muds served as long-term reservoirs for chronic contamination of contiguous coastal communities for over 5 years. One result of the repeated history of oil pollution incidents along this coast was an increased proportion of dead mangrove (Rhizophora mangle) roots in sediment cores which was related to contaminant loading and was detectable for at least 20 years after major oil spills. We suggest that this is the minimum time-scale that is to be expected for the loss of toxicity of oil trapped in muddy coastal habitats impacted by catastrophic oil spills. (author)

Drop Calculations of HLW Canister and Pu Can-in-Canister

International Nuclear Information System (INIS)

Sreten Mastilovic

2001-01-01

The objective of this calculation is to determine the structural response of the standard high-level waste (HLW) canister and the canister containing the cans of immobilized plutonium (Pu) (''can-in-canister'' [CIC] throughout this document) subjected to drop DBEs (design basis events) during the handling operation. The evaluated DBE in the former case is 7-m (23-ft) vertical (flat-bottom) drop. In the latter case, two 2-ft (0.61-m) corner (oblique) drops are evaluated in addition to the 7-m vertical drop. These Pu CIC calculations are performed at three different temperatures: room temperature (RT) (20 C), T = 200 F = 93.3 C , and T = 400 F = 204 C ; in addition to these the calculation characterized by the highest maximum stress intensity is performed at T = 750 F = 399 C as well. The scope of the HLW canister calculation is limited to reporting the calculation results in terms of: stress intensity and effective plastic strain in the canister, directional residual strains at the canister outer surface, and change of canister dimensions. The scope of Pu CIC calculation is limited to reporting the calculation results in terms of stress intensity, and effective plastic strain in the canister. The information provided by the sketches from Reference 26 (Attachments 5.3,5.5,5.8, and 5.9) is that of the potential CIC design considered in this calculation, and all obtained results are valid for this design only. This calculation is associated with the Plutonium Immobilization Project and is performed by the Waste Package Design Section in accordance with Reference 24. It should be noted that the 9-m vertical drop DBE, included in Reference 24, is not included in the objective of this calculation since it did not become a waste acceptance requirement. AP-3.124, ''Calculations'', is used to perform the calculation and develop the document

Release of surfactant cargo from interfacially-active halloysite clay nanotubes for oil spill remediation.

Science.gov (United States)

Owoseni, Olasehinde; Nyankson, Emmanuel; Zhang, Yueheng; Adams, Samantha J; He, Jibao; McPherson, Gary L; Bose, Arijit; Gupta, Ram B; John, Vijay T

2014-11-18

Naturally occurring halloysite clay nanotubes are effective in stabilizing oil-in-water emulsions and can serve as interfacially-active vehicles for delivering oil spill treating agents. Halloysite nanotubes adsorb at the oil-water interface and stabilize oil-in-water emulsions that are stable for months. Cryo-scanning electron microscopy (Cryo-SEM) imaging of the oil-in-water emulsions shows that these nanotubes assemble in a side-on orientation at the oil-water interface and form networks on the interface through end-to-end linkages. For application in the treatment of marine oil spills, halloysite nanotubes were successfully loaded with surfactants and utilized as an interfacially-active vehicle for the delivery of surfactant cargo. The adsorption of surfactant molecules at the interface serves to lower the interfacial tension while the adsorption of particles provides a steric barrier to drop coalescence. Pendant drop tensiometry was used to characterize the dynamic reduction in interfacial tension resulting from the release of dioctyl sulfosuccinate sodium salt (DOSS) from halloysite nanotubes. At appropriate surfactant compositions and loadings in halloysite nanotubes, the crude oil-saline water interfacial tension is effectively lowered to levels appropriate for the dispersion of oil. This work indicates a novel concept of integrating particle stabilization of emulsions together with the release of chemical surfactants from the particles for the development of an alternative, cheaper, and environmentally-benign technology for oil spill remediation.

Environmental considerations in a high desert, crude oil pipeline spill

International Nuclear Information System (INIS)

Lowe, M.A.; Mancini, E.R.; Chamberlain, D.W.; Albright, G.R.

1993-01-01

A road grader punctured a high-pressure crude oil pipeline in the California high desert resulting in the release of approximately 4,200 barrels of Alaska North Slope crude oil. Oil sprayed over a steeply sloped hillside and flowed into an adjacent, densely vegetated ephemeral stream channel which carried secondary treatment sewage discharge. Three underflow dams were constructed in the channel within 2.8 km of the site. To ensure containment at the first dam, the sewage discharge was diverted from the channel, eventually to an upland impulse sprinkler irrigation system. Channel water and phase-separated ANS crude oil, impounded behind the first dam, percolated through alluvial sands/gravels to a depth of about five meters. The oil percolated through the soils on the receding surface of the water, affecting soils to an equivalent depth and saturating a horizontally narrow band of stream-bank soils as much as two to four meters into the bank. Stream channel undergrowth and a small number of mature trees were cleared to provide access for cleanup and/or to remove oiled plants. A large number of trees experienced partial leaf-drop within 25 days of the spill while two heavily oiled trees died. New vegetative growth was evident within five weeks of the spill. Site restoration included planting cuttings of five riparian tree species and hydroseeding exposed banks. Total petroleum hydrocarbon concentrations ranged from not detectable to 203,000 parts per million and averaged approximately 25,000 ppm in affected soils as sampled in place and in stockpiles. Approximately 30,000 tons of hydrocarbon-contaminated soil was excavated from the length of the stream channel (3,600 tons) as well as the area behind the first dam and spill site (26,400 tons). All soils were staged on site for waste profiling and final disposition. After treatment, the contaminated soil was beneficially reused as daily cover at a southern California landfill at a turnkey cost of approximately $57/ton

Quality and Chemical Composition of Organic and Non-Organic Vetiver Oil

Directory of Open Access Journals (Sweden)

Asep Kadarohman

2014-03-01

Full Text Available Vetiver oil (Vetiveria zizanoides has been used as perfume materials, cosmetics, fragrance soaps, anti-inflammation, repellent, and insecticidal agents. Organic vetiver oil has higher economical value than non-organic vetiver oil and it has been regarded to be able to compete in the global market. Therefore, studies have been carried out using 1 hectare of land and the first generation of organic vetiver oil has produced 0.57% of yield, greater than non-organic (0.50%. The quality of organic and non-organic vetiver oil was analyzed by Indonesian Standard (SNI parameter, pesticide residue test, chemical composition by GC/MS, and the appearance of vetiver root. In general, the result of organic and non-organic vetiver oil has fulfilled the national standard; the quality of organic vetiver oil was better than non-organic one. Physically, the appearance of organic vetiver root was better than non-organic vetiver root; organic vetiver root was denser, more appealing, and did not have any black spots. The pesticide residue of organic vetiver oil was lower than non-organic vetiver oil. Based on SNI test, vetiverol (oxygen compounds in organic vetiver oil was higher than non-organic vetiver oil.

A mind cleared by walnut oil: The effects of polyunsaturated and saturated fat on extinction learning.

Science.gov (United States)

Miller, Holly C; Struyf, Dieter; Baptist, Pascale; Dalile, Boushra; Van Oudenhove, Lukas; Van Diest, Ilse

2018-04-07

The treatment of anxiety-based psychopathology often hinges upon extinction learning. Research in nutritional neuroscience has observed that the regular consumption of perilla oil (50% alpha-linolenic acid (ALA)) facilitates extinction learning in rats (Yamamoto et al., 1988). However, acute facilitation of extinction learning by oils rich in ALA has not been reported for rats or humans, though the acute consumption of rapeseed oil (10% ALA) has been observed to improve cognitive processing speed in humans (Jones, Sünram-Lea, & Wesnes, 2012). For this reason, the present laboratory work examined the effects of adding walnut oil (12% ALA) to a chocolate milkshake on the acquisition, generalization, and extinction of a fear-based prediction in young adults. It compared performance between subjects. The other participants consumed a similar milkshake with either an equicaloric amount of cream (saturated fat), or with no added fat (control). Acquisition and generalization of the fear-based prediction were similar for all groups. However, those who consumed walnut oil extinguished most rapidly and profoundly. Implications for extinction learning are discussed. Copyright © 2018. Published by Elsevier Ltd.

Integrated project: Microbiological and physiological studies on the presence of residual concentrations in mineral-oil-contaminated soils after rehabilitation. Final report. Pt. 2; Mikrobiologische und physiologische Untersuchungen zur Frage der Restkonzentration bei der Sanierung mineraloelkontaminierter Boeden. Abschlussbericht. T. 2

Energy Technology Data Exchange (ETDEWEB)

Miethe, D.; Riis, V.; Stimming, M.

1996-01-04

It has been known for a long time that microorganisms are able to utilise mineral oils. Today various methods are practised which exploit autochthonous microorganisms` ability to utilise mineral oils. The main problem of microbial decomposition of hydrocarbons is that mineral oil residues remain. The aim of the present research project was therefore to determine the limits of the metabolisability of the substrate and find out why residues remain. Mineral oils and residual fractions differ markedly in their decomposability. Intermediate distillates are easily decomposed to a degree of 95-97% by well-adapted consorts. For high-boiling mineral oils (bp>400 C) the degree of decomposition is approx. 60%. Extracts from contaminated sites range from 40 to 60% in their degree of decomposability. The incomplete microbial decomposition of mineral oils is mainly due to their structure. There remain chemically and thermally extremely, inert hydrocarbons (mainly aliphatic and aromatic fused-ring systems) which are either hardly metabolisable or not at all. An important factor in soils or at other contaminated sites is that some of the substrate is not available because it is bound to the matrix thus increasing the proportion of residue. The next task after examining and presenting the causes of incomplete decomposition is to minimise residual mineral oil concentrations remaining after microbial decomposition. Here the use of special surfactants or of auxiliary substrates could point a way. Project applications to this end have already been submitted to the Federal Ministry for Education and Research. (orig.) [Deutsch] Dass Mikroorganismen in der Lage sind, Mineraloele zu verwerten, ist seit langem bekannt. Verfahren, die das Potential autochthoner Mikroorganismen zur Verwertung von Mineraloelen nutzen sind Praxis. Hauptproblem beim mikrobiellen Abbau der Kohlenwasserstoffe ist das Verbleiben von Mineraloelresten. Das Ziel des Forschungsvorhabens war die Ermittlung der Grenzen

Research of losses of oil oil and mineral oil at transportation and storage

International Nuclear Information System (INIS)

Akzhigitov, A.S.

2005-01-01

Full text : All way of hydrocarbonic raw material from a mouth of oil wells up to the consumer is accompanied by losses which occur as a result of evaporation, outflow and change of quality. Therefore preservation of quantity and quality of oil and mineral oil during transportation and storages is the major not only economic, but also an ecological problem. The facilitated fractional structure, the big maintenance concern to prominent features of the majority oil from underground salts adjournment Prycaspi in them of the easy hydrocarbons, the raised gas factor in conditions of deposits and presence in structure of gases, except for hydrocarbons and sour a component, - hydrogen sulphide, carbonic gas, etc. The superficial tests stabilized on phase structure oil depending on conditions of preparation for external transport and the subsequent processing can contain this or that quantity of residual hydrogen sulphide, easy hydrocarbons and the lowest sulfhydrates. For change of temperature and external pressure, during transportation and storage the part of easy hydrocarbons and not hydrocarbonic connections (sulfur organic) can be allocated from oil in a gaseous phase and in case of hit in an atmosphere sharply worsens ecology. In the Western Kazakhstan during the years period the temperature of air sometimes reaches up to 40-45 degrees. As is known, at such temperature there is a strengthened warming up of the open surface of oil tanks, that finally leads to increase evaporation easy oil and oil hydrocarbons. With this purpose experiences by quantitative definition evaporation lungs oil and petromixes of the Western Kazakhstan were spent. As a result of the lead works it is found out, that the size of losses at the given fixed temperature depends on evaporation by nature, fractional and hydrocarbonic structures of oil

Quality assessment of biodiesels obtained from pure cooking oils of some feedstocks and their waste oils

International Nuclear Information System (INIS)

Khan, I.; Ansari, T.M.; Manzoor, S.

2017-01-01

Biodiesel being a renewable energy resource possesses compositional variability based on the type of feedstock. Biodiesel is considered a cleaner burning fuel and can be used as pure B100 or blended with petro-diesel. In this study, biodiesel was prepared from pure cooking oils (soybean oil, canola oil, sunflower oil, corn oil) and their waste frying oils by base-catalyzed transesterification with methanol in presence of sodium hydroxide. The optimized experimental parameters were applied to achieve the maximum yield of biodiesel. Various fuel properties like kinematic viscosity, flash point, pour point, cloud point, total acid number, specific gravity, water and sediments, conradson carbon residue, sulfur contents, phosphorous contents, sulphated ash, cetane and copper corrosion were determined and found comparable to ASTM standards. Pure cooking oils, their waste frying oils and prepared biodiesels were characterized by FT-IR. The study showed that the biodiesel derived from waste frying oils can be a promising alternative of the biodiesel from pure cooking oils. (author)

Development of More Effective Biosurfactants for Enhanced Oil Recovery/Advanced Recovery Concepts Awards

Energy Technology Data Exchange (ETDEWEB)

McInerney, M.J.; Marsh, T.L.; Zhang, X.; Knapp, R.M.; Nagle, Jr., D.P.; Sharma, P.K.; Jackson, B.E.

2002-05-28

The objectives of this were two fold. First, core displacement studies were done to determine whether microbial processes could recover residual oil at elevated pressures. Second, the importance of biosurfactant production for the recovery of residual oil was studies. In these studies, a biosurfactant-producing, microorganisms called Bacillus licheniformis strain JF-2 was used. This bacterium produces a cyclic peptide biosurfactant that significantly reduces the interfacial tension between oil and brine (7). The use of a mutant deficient in surfactant production and a mathematical MEOR simulator were used to determine the major mechanisms of oil recovery by these two strains.

eDNA-based bioassessment of coastal sediments impacted by an oil spill.