WorldWideScience

Sample records for chip seals

  1. ChipSeal Inorganic Sealing Technology for Hermetic-Like Integrated Circuits. Volume 1

    Science.gov (United States)

    2000-09-01

    formation (Kerkendall voiding ) and is more susceptible to corrosive attack under adverse conditions. • Degradation of the metallization stack from...processed devices in standard and flip-chip formats, both with and without epoxy encapsulants or underfills . 17 4. Phase I - ChipSeal Process...significant number of bumps exhibited internal voids (Figure 24). A second reflow eliminated the voids open to the surface (Figure 25), but some

  2. Examples of cooler reflective streets for urban heat-island mitigation : Portland cement concrete and chip seals

    Energy Technology Data Exchange (ETDEWEB)

    Pomerantz, M.; Akbari, H.; Chang, S.-C.; Levinson, R.; Pon, B.

    2003-04-30

    Part of the urban heat island effect can be attributed to dark pavements that are commonly used on streets and parking lots. In this paper we consider two light colored, hence cooler, alternative paving materials that are in actual use in cities today. These are Portland cement concrete (PCC) pavements and chip seals. We report measurements of the albedos of some PCC and chip sealed pavements in the San Francisco Bay Area. The albedos of the PCC pavements ranged from about 0.18 to 0.35. The temperatures of some PCC pavements are also measured and calculated. We then consider how the albedos of the constituent materials of the PCC (stone, sand and cement) contribute to the albedos of the resulting finished concrete. The albedos of a set of chip sealed pavements in San Jose, CA, were measured and correlated with the times of their placement. It is found that the albedos decrease with age (and use) but remain higher than that of standard asphalt concrete (AC) for about five years. After t hat, the albedos of the chip seals are about 0.12, similar to aged AC. The fact that many PCC pavements have albedos at least twice as high as aged AC suggests that it is possible to have pavement albedos that remain high for many years.

  3. Development of Performance-Related Specification for Fresh Emulsions Used for Surface Treatments and Performance Study of Chip Seals and Microsurfacing

    Science.gov (United States)

    Ilias, Mohammad

    Pavement preservation is a rapidly growing strategy for prolonging pavement service life. Pavement preservation consists of applying a thin layer of asphalt binder or emulsion with or without aggregate to the surface of an existing pavement. Preservation treatments do not provide any structural strength to the pavement but restores skid resistance, seals existing cracks, protects the underlying pavement from intrusion of water, and reduces further oxidative aging of the underlying pavement. In recent years, significant research has been dedicated to improving design of pavement preservation treatments. In pavement preservation treatments, asphalt emulsion is the predominant binding material used because of its low viscosity compared to asphalt cement which allows for production at greatly reduced temperatures, leading to energy efficiency, and potential cost savings. Currently, specifications for emulsions used in pavement preservation treatments are empirical and lack of direct relationship to performance. This study seeks to improve specifications for emulsions used in preservation treatments by developing performancerelated specifications (PRS) for (a) fresh emulsion properties, (b) microsurfacing emulsion residue, and (c) low-temperature raveling of chip seal emulsion residues. Fresh emulsion properties dictate constructability and stability, and consequently the resultant performance of a preservation treatment once placed. Specification test methods are proposed for chip seals, microsurfacings, and spray seals that reflect storage and construction conditions of the emulsions. Performance is quantified using viscosity measurements. Specification limits are determined based on a prior knowledge of emulsion performance coupled with statistical analyses. Microsurfacings are a preservation treatment consisting of application of a thin layer of asphalt emulsion -- fine aggregate mixture. Presently, mixture design and performances of microsurfacing mixtures are

  4. Seals and sealing handbook

    CERN Document Server

    Flitney, Robert K

    2014-01-01

    Seals and Sealing Handbook, 6th Edition provides comprehensive coverage of sealing technology, bringing together information on all aspects of this area to enable you to make the right sealing choice. This includes detailed coverage on the seals applicable to static, rotary and reciprocating applications, the best materials to use in your sealing systems, and the legislature and regulations that may impact your sealing choices. Updated in line with current trends this updated reference provides the theory necessary for you to select the most appropriate seals for the job and with its 'Failur

  5. Seals and sealing handbook

    CERN Document Server

    Flitney, Robert K

    2007-01-01

    Wherever machinery operates there will be seals of some kind ensuring that the machine remains lubricated, the fluid being pumped does not leak, or the gas does not enter the atmosphere. Seals are ubiquitous, in industry, the home, transport and many other places. This 5th edition of a long-established title covers all types of seal by application: static, rotary, reciprocating etc. The book bears little resemblance to its predecessors, and Robert Flitney has re-planned and re-written every aspect of the subject. No engineer, designer or manufacturer of seals can afford to be without this uniq

  6. Glass sealing

    Energy Technology Data Exchange (ETDEWEB)

    Brow, R.K.; Kovacic, L.; Chambers, R.S. [Sandia National Labs., Albuquerque, NM (United States)

    1996-04-01

    Hernetic glass sealing technologies developed for weapons component applications can be utilized for the design and manufacture of fuel cells. Design and processing of of a seal are optimized through an integrated approach based on glass composition research, finite element analysis, and sealing process definition. Glass sealing procedures are selected to accommodate the limits imposed by glass composition and predicted calculations.

  7. Mechanical seals

    CERN Document Server

    Mayer, E

    1977-01-01

    Mechanical Seals, Third Edition is a source of practical information on the design and use of mechanical seals. Topics range from design fundamentals and test rigs to leakage, wear, friction and power, reliability, and special designs. This text is comprised of nine chapters; the first of which gives a general overview of seals, including various types of seals and their applications. Attention then turns to the fundamentals of seal design, with emphasis on six requirements that must be considered: sealing effectiveness, length of life, reliability, power consumption, space requirements, and c

  8. Ceramic Seal.

    Energy Technology Data Exchange (ETDEWEB)

    Smartt, Heidi A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Romero, Juan A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Custer, Joyce Olsen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hymel, Ross W. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Krementz, Dan [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Gobin, Derek [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Harpring, Larry [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Martinez-Rodriguez, Michael [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Varble, Don [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); DiMaio, Jeff [Tetramer Technologies, Pendleton, SC (United States); Hudson, Stephen [Tetramer Technologies, Pendleton, SC (United States)

    2016-11-01

    Containment/Surveillance (C/S) measures are critical to any verification regime in order to maintain Continuity of Knowledge (CoK). The Ceramic Seal project is research into the next generation technologies to advance C/S, in particular improving security and efficiency. The Ceramic Seal is a small form factor loop seal with improved tamper-indication including a frangible seal body, tamper planes, external coatings, and electronic monitoring of the seal body integrity. It improves efficiency through a self-securing wire and in-situ verification with a handheld reader. Sandia National Laboratories (SNL) and Savannah River National Laboratory (SRNL), under sponsorship from the U.S. National Nuclear Security Administration (NNSA) Office of Defense Nuclear Nonproliferation Research and Development (DNN R&D), have previously designed and have now fabricated and tested Ceramic Seals. Tests have occurred at both SNL and SRNL, with different types of tests occurring at each facility. This interim report will describe the Ceramic Seal prototype, the design and development of a handheld standalone reader and an interface to a data acquisition system, fabrication of the seals, and results of initial testing.

  9. Ferrules seals

    Science.gov (United States)

    Smith, J.L.

    1984-07-10

    A device is provided for sealing an inner tube and an outer tube without excessively deforming the tubes. The device includes two ferrules which cooperate to form a vacuum-tight seal between the inner tube and outer tube and having mating surfaces such that overtightening is not possible. 3 figs.

  10. Seal Counts

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Database of seal counts from aerial photography. Counts by image, site, species, and date are stored in the database along with information on entanglements and...

  11. Python fiber optic seal

    Energy Technology Data Exchange (ETDEWEB)

    Ystesund, K.; Bartberger, J.; Brusseau, C.; Fleming, P.; Insch, K.; Tolk, K.

    1993-08-01

    Sandia National Laboratories has developed a high security fiber optic seal that incorporates tamper resistance features that are not available in commercial fiber optic seals. The Python Seal is a passive fiber optic loop seal designed to give indication of unauthorized entry. The seal includes a fingerprint feature that provides seal identity information in addition to the unique fiber optic pattern created when the seal is installed. The fiber optic cable used for the seal loop is produced with tamper resistant features that increase the difficulty of attacking that component of a seal. A Seal Reader has been developed that will record the seal signature and the fingerprint feature of the seal. A Correlator software program then compares seal images to establish a match or mismatch. SNL is also developing a Polaroid reader to permit hard copies of the seal patterns to be obtained directly from the seal.

  12. Turbine with radial acting seal

    Energy Technology Data Exchange (ETDEWEB)

    Eng, Darryl S; Ebert, Todd A

    2016-11-22

    A floating brush seal in a rim cavity of a turbine in a gas turbine engine, where the floating brush seal includes a seal holder in which the floating brush seal floats, and a expandable seal that fits within two radial extending seal slots that maintains a seal with radial displacement of the floating brush seal and the seal holder.

  13. Chip, Chip, Hooray!

    Science.gov (United States)

    Kelly, Susan

    2001-01-01

    Presents a science laboratory using different brands of potato chips in which students test their oiliness, size, thickness, saltiness, quality, and cost, then analyze the results to determine the best chip. Gives a brief history of potato chips. (YDS)

  14. Regenerator seal

    Science.gov (United States)

    Davis, Leonard C.; Pacala, Theodore; Sippel, George R.

    1981-01-01

    A method for manufacturing a hot side regenerator cross arm seal assembly having a thermally stablilized wear coating with a substantially flat wear surface thereon to seal between low pressure and high pressure passages to and from the hot inboard side of a rotary regenerator matrix includes the steps of forming a flat cross arm substrate member of high nickel alloy steel; fixedly securing the side edges of the substrate member to a holding fixture with a concave surface thereacross to maintain the substrate member to a slightly bent configuration on the fixture surface between the opposite ends of the substrate member to produce prestress therein; applying coating layers on the substrate member including a wear coating of plasma sprayed nickel oxide/calcium flouride material to define a wear surface of slightly concave form across the restrained substrate member between the free ends thereon; and thereafter subjecting the substrate member and the coating thereon to a heat treatment of 1600.degree. F. for sixteen hours to produce heat stabilizing growth in the coating layers on the substrate member and to produce a thermally induced growth stress in the wear surface that substantially equalizes the prestress in the substrate whereby when the cross arm is removed from the fixture surface following the heat treatment step a wear face is formed on the cross arm assembly that will be substantially flat between the ends.

  15. Seal design alternatives study

    Energy Technology Data Exchange (ETDEWEB)

    Van Sambeek, L.L. [RE/SPEC Inc., Rapid City, SD (US); Luo, D.D.; Lin, M.S.; Ostrowski, W.; Oyenuga, D. [Parsons Brinckerhoff Quade & Douglas, Inc., San Francisco, CA (US)

    1993-06-01

    This report presents the results from a study of various sealing alternatives for the WIPP sealing system. Overall, the sealing system has the purpose of reducing to the extent possible the potential for fluids (either gas or liquid) from entering or leaving the repository. The sealing system is divided into three subsystems: drift and panel seals within the repository horizon, shaft seals in each of the four shafts, and borehole seals. Alternatives to the baseline configuration for the WIPP seal system design included evaluating different geometries and schedules for seal component installations and the use of different materials for seal components. Order-of-magnitude costs for the various alternatives were prepared as part of the study. Firm recommendations are not presented, but the advantages and disadvantages of the alternatives are discussed. Technical information deficiencies are identified and studies are outlined which can provide required information.

  16. Magnetically Actuated Seal

    Science.gov (United States)

    Pinera, Alex

    2013-01-01

    This invention is a magnetically actuated seal in which either a single electromagnet, or multiple electromagnets, are used to control the seal's position. This system can either be an open/ close type of system or an actively controlled system.

  17. Magnetically Actuated Seal Project

    Data.gov (United States)

    National Aeronautics and Space Administration — FTT proposes development of a magnetically actuated dynamic seal. Dynamic seals are used throughout the turbopump in high-performance, pump-fed, liquid rocket...

  18. Turbomachine Interface Sealing

    Science.gov (United States)

    Hendricks, Robert C.; Chupp, Raymond E.; Lattime, Scott B.; Steinetz, Bruce M.

    2005-01-01

    Sealing interfaces and coatings, like lubricants, are sacrificial, giving up their integrity for the benefit of the component. Clearance control is a major issue in power systems turbomachine design and operational life. Sealing becomes the most cost-effective way to enhance system performance. Coatings, films, and combined use of both metals and ceramics play a major role in maintaining interface clearances in turbomachine sealing and component life. This paper focuses on conventional and innovative materials and design practices for sealing interfaces.

  19. Seals For Cryogenic Turbomachines

    Science.gov (United States)

    Hendricks, Robert C.; Tam, L. T.; Braun, M. J.; Vlcek, B. L.

    1988-01-01

    Analysis considers effects of seals on stability. Report presents method of calculation of flows of cryogenic fluids through shaft seals. Key to stability is local average velocity in seal. Local average velocity strongly influenced by effects of inlet and outlet and injection of fluid.

  20. Fabrication technology of integrated fiber microfluidic electrophoresis chip

    Institute of Scientific and Technical Information of China (English)

    LI MengChun

    2007-01-01

    The technology of PCB was used to fabricate the chip mould, and the microfluidic electrophoresis chip was fabricated with PDMS material. The fiber integrated on the chip was used as the transmission medium, so the light spot size was near the depth of microchannel. The detection sensitivity was improved, and the optical focusing system was spared. The fabrication process, sealing methods and structure characteristic of PDMS microfluidic electrophoresis chips were discussed. The experiment was achieved by using the fabricated chip to separate FITC fluorescein and FITC-labeled amino acid mixture reagent, and the feasibility of the chip was validated.

  1. Low Cost, Durable Seal

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, George; Parsons, Jason; Friedman, Jake

    2010-12-17

    Seal durability is critical to achieving the 2010 DOE operational life goals for both stationary and transportation PEM fuel cell stacks. The seal material must be chemically and mechanically stable in an environment consisting of aggressive operating temperatures, humidified gases, and acidic membranes. The seal must also be producible at low cost. Currentlyused seal materials do not meet all these requirements. This project developed and demonstrated a high consistency hydrocarbon rubber seal material that was able to meet the DOE technical and cost targets. Significant emphasis was placed on characterization of the material and full scale molding demonstrations.

  2. Zero leakage sealings

    Science.gov (United States)

    Kotesovec, Bernhard; Steinrück, Herbert

    2010-11-01

    The piston rod of a reciprocating compressor is sealed with elastic cylindrical sealing elements. Across the sealings the pressure drops from the operating pressure to the ambient pressure. The lubrication gap between the elastic sealing and reciprocating piston rod is studied with the aim to find conditions of a leakage free sealing. The flow in the lubrication gap and the elastic deformation of the sealing are determined simultaneously. The net-flow during one cycle of the reciprocating piston rod is calculated. It turns out that maintaining zero leakage is very sensible. Indeed the outbound flow during out-stroke has to be equal the inbound flow during the in-stroke. By prescribing a special shape of the undeformed sealing zero leakage can be attained - at least theoretically for certain operating conditions. It turns out that temperature dependent material data and a model for cavitation is necessary. The model, its numerical implementation and results will be discussed.

  3. Dynamic sealing principles

    Science.gov (United States)

    Zuk, J.

    1976-01-01

    The fundamental principles governing dynamic sealing operation are discussed. Different seals are described in terms of these principles. Despite the large variety of detailed construction, there appear to be some basic principles, or combinations of basic principles, by which all seals function, these are presented and discussed. Theoretical and practical considerations in the application of these principles are discussed. Advantages, disadvantages, limitations, and application examples of various conventional and special seals are presented. Fundamental equations governing liquid and gas flows in thin film seals, which enable leakage calculations to be made, are also presented. Concept of flow functions, application of Reynolds lubrication equation, and nonlubrication equation flow, friction and wear; and seal lubrication regimes are explained.

  4. Applications of quantum message sealing

    CERN Document Server

    Worley, G G

    2005-01-01

    In 2003, Bechmann-Pasquinucci introduced the concept of quantum seals, a quantum analogue to wax seals used to close letters and envelopes. Since then, some improvements on the method have been found. We first review the current quantum sealing techniques, then introduce and discuss potential applications of quantum message sealing, and conclude with some discussion of the limitations of quantum seals.

  5. Repository seals requirements study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-03

    The Yucca Mountain Site Characterization Project, managed by the Civilian Radioactive Waste Management System (CRWMS) Management and Operating Contractor (M and O) is conducting investigations to support the Viability Assessment and the License Application for a high-level nuclear waste repository at Yucca Mountain, Nevada. The sealing subsystem is part of the Yucca Mountain Waste Isolation System. The Yucca Mountain Site Characterization Project is currently evaluating the role of the sealing subsystem (shaft, ramp and exploratory borehole seals) in achieving the overall performance objectives for the Waste Isolation System. This report documents the results of those evaluations. This report presents the results of a repository sealing requirements study. Sealing is defined as the permanent closure of the shafts, ramps, and exploratory boreholes. Sealing includes those components that would reduce potential inflows above the repository, or that would divert flow near the repository horizon to allow vertical infiltration to below the repository. Sealing of such features as emplacement drifts was not done in this study because the current capability to calculate fracture flow into the drifts is not sufficiently mature. The objective of the study is to provide water or air flow performance based requirements for shafts, ramps, and exploratory boreholes located near the repository. Recommendations, as appropriate, are provided for developing plans, seals component testing, and other studies relating to sealing.

  6. High Test Peroxide High Sealing Conical Seal Project

    Data.gov (United States)

    National Aeronautics and Space Administration — High Test Peroxide (HTP) Highly Compatible High Sealing Conical Seals are necessary for ground test operations and space based applications. Current conical seals...

  7. Saving Seal Cutting

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    On April 20, the graduation ceremony of China’s seal-cutting art postgraduates and visiting experts from the Institute of Seal Cutting Art under the China Art Academy was held in Beijing. On the same day, the exhibition of the works of the teachers and graduates of the institute was also held.

  8. Programmable Multi-Chip Module

    Science.gov (United States)

    Kautz, David; Morgenstern, Howard; Blazek, Roy J.

    2004-11-16

    A multi-chip module comprising a low-temperature co-fired ceramic substrate having a first side on which are mounted active components and a second side on which are mounted passive components, wherein this segregation of components allows for hermetically sealing the active components with a cover while leaving accessible the passive components, and wherein the passive components are secured using a reflow soldering technique and are removable and replaceable so as to make the multi-chip module substantially programmable with regard to the passive components.

  9. Sealing device for providing a seal in a turbomachine

    Science.gov (United States)

    Lacy, Benjamin Paul; Kottilingam, Srikanth Chandrudu; Porter, Christopher Donald; Schick, David Edward; Weber, David Wayne

    2016-08-16

    Sealing device for providing seals between adjacent components, and turbomachines utilizing such sealing devices, are provided. A sealing device includes a seal plate insertable between the adjacent components, the seal plate comprising a first face and an opposing second face. The sealing device further includes a plurality of pins extending from one of the first face or the second face, the plurality of pins configured to space the one of the first face or the second face from contact surfaces of the adjacent components.

  10. Fur seal investigations, 1966

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Annually a report is made on the fur seal investigations carried on by the Bureau of Commercial Fisheries on the Pribilof Islands and at sea. Investigations on the...

  11. Ribbon Seal Distribution Map

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains GIS layers that depict the known spatial distributions (i.e., ranges) and reported breeding areas of ribbon seals (Histriophoca fasciata). It...

  12. Ringed Seal Distribution Map

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains GIS layers that depict the known spatial distributions (i.e., ranges) of the five subspecies of ringed seals (Phoca hispida). It was produced...

  13. Bearded Seal Distribution Map

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains GIS layers that depict the known spatial distributions (i.e., ranges) of the two subspecies of bearded seals (Erignathus barbatus). It was...

  14. Spotted Seal Distribution Map

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains GIS layers that depict the known spatial distributions (i.e., ranges) and reported breeding areas of spotted seals (Phoca largha). It was...

  15. Sliding seal for mining machine power transmission

    Energy Technology Data Exchange (ETDEWEB)

    Levenstein, V.M.

    1993-07-06

    A generally tubular sealing mechanism is described for use in the power train of a mining machine to seal between an annular seal face on one of two spaced apart units in the power train and a sealing ring surface on the other of said units for sealed protection of a drive shaft connected between said two units, said sealing mechanism including a tubular seal carrier with a first end portion having a cylindrical sealing surface for being telescoped with said sealing ring surface, an annular seal element mountable on said cylindrical sealing surface for sealing engagement between said sealing ring surface and said cylindrical sealing surface, said carrier further having a second end portion with a radially extending face, a clamp connectable between said one unit and said carrier for urging said radially extending face toward said annular seal face, and a sealing member mountable in sealing engagement between said annular seal face and said radially extending face.

  16. THE ORIGINS OF SEALS AND SEALING IN CHINA

    Institute of Scientific and Technical Information of China (English)

    1994-01-01

    The origin of Chinese seals remains obscure in modern research. Most publications, influenced by the traditional point of view, have dealt with the seals handed down from the Eastern Zhou (771-256 B.C.). Only a few studies have discussed seals from their earliest-and still neglected-history. There have even been some suggestions, based on the idea of using a seal and using it on clay first developed in Mesopotamia, that the seal was introduced to China from the Near East. This proposed foreign origin makes the history of Chinese seals more complicated.

  17. World-to-chip microfluidic interface with built-in valves for multichamber chip-based PCR assays.

    Science.gov (United States)

    Oh, Kwang W; Park, Chinsung; Namkoong, Kak; Kim, Jintae; Ock, Kyeong-Sik; Kim, Suhyeon; Kim, Young-A; Cho, Yoon-Kyoung; Ko, Christopher

    2005-08-01

    We report a practical world-to-chip microfluidic interfacing method with built-in valves suitable for microscale multichamber chip-based assays. One of the primary challenges associated with the successful commercialization of fully integrated microfluidic systems has been the lack of reliable world-to-chip microfluidic interconnections. After sample loading and sealing, leakage tests were conducted at 100 degrees C for 30 min and no detectable leakage flows were found during the test for 100 microchambers. To demonstrate the utility of our world-to-chip microfluidic interface, we designed a microscale PCR chip with four chambers and performed PCR assays. The PCR results yielded a 100% success rate with no contamination or leakage failures. In conclusion, we have introduced a simple and inexpensive microfluidic interfacing system for both sample loading and sealing with no dead volume, no leakage flow and biochemical compatibility.

  18. Wax-bonding 3D microfluidic chips

    KAUST Repository

    Gong, Xiuqing

    2013-10-10

    We report a simple, low-cost and detachable microfluidic chip incorporating easily accessible paper, glass slides or other polymer films as the chip materials along with adhesive wax as the recycling bonding material. We use a laser to cut through the paper or film to form patterns and then sandwich the paper and film between glass sheets or polymer membranes . The hot-melt adhesive wax can realize bridge bonding between various materials, for example, paper, polymethylmethacrylate (PMMA) film, glass sheets, or metal plate. The bonding process is reversible and the wax is reusable through a melting and cooling process. With this process, a three-dimensional (3D) microfluidic chip is achievable by vacuating and venting the chip in a hot-water bath. To study the biocompatibility and applicability of the wax-based microfluidic chip, we tested the PCR compatibility with the chip materials first. Then we applied the wax-paper based microfluidic chip to HeLa cell electroporation (EP ). Subsequently, a prototype of a 5-layer 3D chip was fabricated by multilayer wax bonding. To check the sealing ability and the durability of the chip, green fluorescence protein (GFP) recombinant Escherichia coli (E. coli) bacteria were cultured, with which the chemotaxis of E. coli was studied in order to determine the influence of antibiotic ciprofloxacin concentration on the E. coli migration.

  19. Sealing coupling. [LMFBR

    Science.gov (United States)

    Pardini, J.A.; Brubaker, R.C.; Rusnak, J.J.

    1982-09-20

    Disclosed is a remotely operable releasable sealing coupling which provides fluid-tight joinder of upper and a lower conduit sections. Each conduit section has a concave conical sealing surface adjacent its end portion. A tubular sleeve having convex spherical ends is inserted between the conduit ends to form line contact with the concave conical end portions. An inwardly projecting lip located at one end of the sleeve cooperates with a retaining collar formed on the upper pipe end to provide swivel capture for the sleeve. The upper conduit section also includes a tapered lower end portion which engages the inside surface of the sleeve to limit misalignment of the connected conduit sections.

  20. GOLD PRESSURE VESSEL SEAL

    Science.gov (United States)

    Smith, A.E.

    1963-11-26

    An improved seal between the piston and die member of a piston-cylinder type pressure vessel is presented. A layer of gold, of sufficient thickness to provide an interference fit between the piston and die member, is plated on the contacting surface of at least one of the members. (AEC)

  1. Mechanical Face Seal Dynamics.

    Science.gov (United States)

    1985-12-01

    These liquids range from lubricants to highly toxic chemicals and acids. The applications range from helicopter transmissions to nuclear reactor... Analit ~is., N ,iontat ting lame St-ak"ts fnn. ASXIE namin Behaioir ni Nonmmuiam ing (knied-Fate Mechanikal Seals:* SL /I ub In h. 104. 1. 111 *)6ii-414

  2. Ceramic to metal seal

    Energy Technology Data Exchange (ETDEWEB)

    Snow, Gary S. (Albuquerque, NM); Wilcox, Paul D. (Albuquerque, NM)

    1976-01-01

    Providing a high strength, hermetic ceramic to metal seal by essentially heating a wire-like metal gasket and a ceramic member, which have been chemically cleaned, while simultaneously deforming from about 50 to 95 percent the metal gasket against the ceramic member at a temperature of about 30 to 75 percent of the melting temperature of the metal gasket.

  3. Detection of grey seal

    NARCIS (Netherlands)

    van Bleijswijk, J.; Begeman, L.; Witte, H.J.; IJsseldijk, L.L.; Brasseur, S.M.J.M.; Gröne, A.; Leopold, M.F.

    2014-01-01

    DNA was analysed from external wounds on 3 dead harbour porpoises Phocoena phocoena that were stranded in the Netherlands. Puncture wounds as well as the edges of large open wounds were sampled with sterile cotton swabs. With specific primers that target the mtDNA control region of grey seal Halicho

  4. Seals Having Textured Portions for Protection in Space Environments

    Science.gov (United States)

    Daniels, Christopher (Inventor); Garafolo, Nicholas (Inventor)

    2016-01-01

    A sealing construct for a space environment includes a seal-bearing object, a seal on the seal-bearing object, and a seal-engaging object. The seal includes a seal body having a sealing surface, and a textured pattern at the sealing surface, the textured pattern defining at least one shaded channel surface. The seal-engaging object is selectively engaged with the seal-bearing object through the seal. The seal-engaging object has a sealing surface, wherein, when the seal-engaging object is selectively engaged with the seal-bearing object, the sealing surface of the seal-engaging object engages the sealing surface of the seal, and the seal is compressed between the seal-bearing object and the seal-engaging object such that at least one shaded channel surface engages the sealing surface of the seal-engaging object.

  5. Regenerator cross arm seal assembly

    Science.gov (United States)

    Jackman, Anthony V.

    1988-01-01

    A seal assembly for disposition between a cross arm on a gas turbine engine block and a regenerator disc, the seal assembly including a platform coextensive with the cross arm, a seal and wear layer sealingly and slidingly engaging the regenerator disc, a porous and compliant support layer between the platform and the seal and wear layer porous enough to permit flow of cooling air therethrough and compliant to accommodate relative thermal growth and distortion, a dike between the seal and wear layer and the platform for preventing cross flow through the support layer between engine exhaust and pressurized air passages, and air diversion passages for directing unregenerated pressurized air through the support layer to cool the seal and wear layer and then back into the flow of regenerated pressurized air.

  6. Atom chips

    CERN Document Server

    Reichel, Jakob

    2010-01-01

    This book provides a stimulating and multifaceted picture of a rapidly developing field. The first part reviews fundamentals of atom chip research in tutorial style, while subsequent parts focus on the topics of atom-surface interaction, coherence on atom chips, and possible future directions of atom chip research. The articles are written by leading researchers in the field in their characteristic and individual styles.

  7. Sealing the Mitochondrial Respirasome

    OpenAIRE

    Winge, Dennis R.

    2012-01-01

    The mitochondrial respiratory chain is organized within an array of supercomplexes that function to minimize the generation of reactive oxygen species (ROS) during electron transfer reactions. Structural models of supercomplexes are now known. Another recent advance is the discovery of non-OXPHOS complex proteins that appear to adhere to and seal the individual respiratory complexes to form stable assemblages that prevent electron leakage. This review highlights recent advances in our underst...

  8. A sealing element

    Energy Technology Data Exchange (ETDEWEB)

    Obi, F.; Takada, K.

    1983-09-22

    A sealing lining made of a mixture of polyethylene or polypropylene with an additive which prevents destruction of the lining is used in the element. The content of the additive in the mixture is 10 to 30 percent by mass. The additive basically consists of polyethylene. Carboxyl groups are introduced into the polymer as an anion and sodium, potassium and molybdenum are introduced as the cation.

  9. Navy GTE seal development activity

    Science.gov (United States)

    Grala, Carl P.

    1993-10-01

    Under the auspices of the Integrated High Performance Turbine Engine Technology Initiative, the Naval Air Warfare Center conducts advanced development programs for demonstration in the next generation of air-breathing propulsion systems. Among the target technologies are gas path and lube oil seals. Two development efforts currently being managed by NAWCAD are the High Performance Compressor Discharge Film-Riding Face Seal and the Subsonic Core High Speed Air/Oil Seal. The High Performance Compressor Discharge Film-Riding Face Seal Program aims at reducing parasitic leakage through application of a film-riding face sea concept to the compressor discharge location of a Phase 2 IHPTET engine. An order-of-magnitude leakage reduction relative to current labyrinth seal configurations is expected. Performance goals for these seals are (1) 1200 F air temperature, (2) 800 feet-per-second surface velocity, and (3) 600 SPI differential pressure. The two designs chosen for fabrication and rig test are a spiral groove and a Rayleigh step seal. Rig testing is currently underway. The Subsonic Core High Speed Air/Oil Seal Program is developing shaft-to-ground seals for next-generation propulsion systems that will minimize leakage and provide full life. Significantly higher rotor speeds and temperatures will be experienced. Technologies being exploited include, hydrodynamic lift assist features, ultra light weight designs, and improved cooling schemes. Parametric testing has been completed; a final seal design is entering the endurance test phase.

  10. TECHNOLOGY ROADMAPPING FOR IAEA SEALS.

    Energy Technology Data Exchange (ETDEWEB)

    HOFFHEINS,B.; ANNESE,C.; GOODMAN,M.; OCONNOR,W.; GUSHUE,S.; PEPPER,S.

    2003-07-13

    In the fall of 2002, the U.S. Support Program (USSP) initiated an effort to define a strategy or ''roadmap'' for future seals technologies and to develop a generalized process for planning safeguards equipment development, which includes seals and other safeguards equipment. The underlying objectives of the USSP include becoming more proactive than reactive in addressing safeguards equipment needs, helping the IAEA to maintain an inventory of cost-effective, reliable, and effective safeguards equipment, establishing a long-term planning horizon, and securing IAEA ownership in the process of effective requirements definition and timely transitioning of new or improved systems for IAEA use. At an initial workshop, seals, their functions, performance issues, and future embodiments were discussed in the following order: adhesive seals, metal seals, passive and active loop seals, ultrasonic seals, tamper indicating enclosures (including sample containers, equipment enclosures, and conduits). Suggested improvements to these technologies focused largely on a few themes: (1) The seals must be applied quickly, easily, and correctly; (2) Seals and their associated equipment should not unduly add bulk or weight to the inspectors load; (3) Rapid, in-situ verifiability of seals is desirable; and (4) Seal systems for high risk or high value applications should have two-way, remote communications. Based upon these observations and other insights, the participants constructed a skeletal approach for seals technology planning. The process begins with a top-level review of the fundamental safeguards requirements and extraction of required system features, which is followed by analysis of suitable technologies and identification of technology gaps, and finally by development of a planning schedule for system improvements and new technology integration. Development of a comprehensive procedure will require the partnership and participation of the IAEA. The

  11. Closure and Sealing Design Calculation

    Energy Technology Data Exchange (ETDEWEB)

    T. Lahnalampi; J. Case

    2005-08-26

    The purpose of the ''Closure and Sealing Design Calculation'' is to illustrate closure and sealing methods for sealing shafts, ramps, and identify boreholes that require sealing in order to limit the potential of water infiltration. In addition, this calculation will provide a description of the magma that can reduce the consequences of an igneous event intersecting the repository. This calculation will also include a listing of the project requirements related to closure and sealing. The scope of this calculation is to: summarize applicable project requirements and codes relating to backfilling nonemplacement openings, removal of uncommitted materials from the subsurface, installation of drip shields, and erecting monuments; compile an inventory of boreholes that are found in the area of the subsurface repository; describe the magma bulkhead feature and location; and include figures for the proposed shaft and ramp seals. The objective of this calculation is to: categorize the boreholes for sealing by depth and proximity to the subsurface repository; develop drawing figures which show the location and geometry for the magma bulkhead; include the shaft seal figures and a proposed construction sequence; and include the ramp seal figure and a proposed construction sequence. The intent of this closure and sealing calculation is to support the License Application by providing a description of the closure and sealing methods for the Safety Analysis Report. The closure and sealing calculation will also provide input for Post Closure Activities by describing the location of the magma bulkhead. This calculation is limited to describing the final configuration of the sealing and backfill systems for the underground area. The methods and procedures used to place the backfill and remove uncommitted materials (such as concrete) from the repository and detailed design of the magma bulkhead will be the subject of separate analyses or calculations. Post

  12. Microchannel cooling of face down bonded chips

    Science.gov (United States)

    Bernhardt, Anthony F.

    1993-01-01

    Microchannel cooling is applied to flip-chip bonded integrated circuits, in a manner which maintains the advantages of flip-chip bonds, while overcoming the difficulties encountered in cooling the chips. The technique is suited to either multichip integrated circuit boards in a plane, or to stacks of circuit boards in a three dimensional interconnect structure. Integrated circuit chips are mounted on a circuit board using flip-chip or control collapse bonds. A microchannel structure is essentially permanently coupled with the back of the chip. A coolant delivery manifold delivers coolant to the microchannel structure, and a seal consisting of a compressible elastomer is provided between the coolant delivery manifold and the microchannel structure. The integrated circuit chip and microchannel structure are connected together to form a replaceable integrated circuit module which can be easily decoupled from the coolant delivery manifold and the circuit board. The coolant supply manifolds may be disposed between the circuit boards in a stack and coupled to supplies of coolant through a side of the stack.

  13. Sealing the mitochondrial respirasome.

    Science.gov (United States)

    Winge, Dennis R

    2012-07-01

    The mitochondrial respiratory chain is organized within an array of supercomplexes that function to minimize the generation of reactive oxygen species (ROS) during electron transfer reactions. Structural models of supercomplexes are now known. Another recent advance is the discovery of non-OXPHOS complex proteins that appear to adhere to and seal the individual respiratory complexes to form stable assemblages that prevent electron leakage. This review highlights recent advances in our understanding of the structures of supercomplexes and the factors that mediate their stability.

  14. Performance Evaluation of an Actuator Dust Seal for Lunar Operation

    Science.gov (United States)

    Delgado, Irebert R.; Gaier, James R.; Handschuh, Michael; Panko, Scott; Sechkar, Ed

    2013-01-01

    Exploration of extraterrestrial surfaces (e.g. moon, Mars, asteroid) will require durable space mechanisms that will survive potentially dusty surface conditions in addition to the hard vacuum and extreme temperatures of space. Baseline tests with lunar simulant were recently completed at NASA GRC on a new Low-Temperature Mechanism (LTM) dust seal for space actuator application. Following are top-level findings of the tests completed to date in vacuum using NU-LHT-2M lunar-highlands simulant. A complete set of findings are found in the conclusions section.Tests were run at approximately 10-7 torr with unidirectional rotational speed of 39 RPM.Initial break-in runs were performed at atmospheric conditions with no simulant. During the break-in runs, the maximum torque observed was 16.7 lbf-in. while the maximum seal outer diameter temperature was 103F. Only 0.4 milligrams of NU-LHT-2M simulant passed through the sealshaft interface in the first 511,000 cycles while under vacuum despite a chip on the secondary sealing surface.Approximately 650,000 of a planned 1,000,000 cycles were completed in vacuum with NU-LHT-2M simulant.Upon test disassembly NU-LHT-2M was found on the secondary sealing surface.

  15. Face-Sealing Butterfly Valve

    Science.gov (United States)

    Tervo, John N.

    1992-01-01

    Valve plate made to translate as well as rotate. Valve opened and closed by turning shaft and lever. Interactions among lever, spring, valve plate, and face seal cause plate to undergo combination of translation and rotation so valve plate clears seal during parts of opening and closing motions.

  16. Seals. Grades 3-6.

    Science.gov (United States)

    New England Aquarium, Boston, MA.

    Explanations of a marine mammal rescue program and information on seals and sea lions are presented in this curriculum package for intermediate grade teachers. Activities are highlighted which focus on the natural history of harbor seals. This unit contains: (1) pre-trip activities (including fact sheets and worksheets on the different types of…

  17. Gulf and Dilmun Type seals

    DEFF Research Database (Denmark)

    Laursen, Steffen

    2011-01-01

    these Gulf Type‘ seals drew heavily on Indus Valley iconography and Indus script was occasionally employed in a pidgin-like manner. While the earliest circular seals incorporate features from Mesopotamian glyptic only to a lesser extent, this becomes a more important source of inspiration for later Dilmun...

  18. Gas-path seal technology

    Science.gov (United States)

    Zuk, J.

    1976-01-01

    Improved gas-path seals are needed for better fuel economy, longer performance retention, and lower maintenance, particularly in advanced, high-performance gas turbine engines. Problems encountered in gas-path sealing are described, as well as new blade-tip sealing approaches for high-pressure compressors and turbines. These include a lubricant coating for conventional, porous-metal, rub-strip materials used in compressors. An improved hot-press metal alloy shows promise to increase the operating surface temperatures of high-pressure-turbine, blade-tip seals to 1450 K (2150 F). Three ceramic seal materials are also described that have the potential to allow much higher gas-path surface operating temperatures than are possible with metal systems.

  19. Aerodynamic seals for rotary machine

    Energy Technology Data Exchange (ETDEWEB)

    Bidkar, Rahul Anil; Cirri, Massimiliano; Thatte, Azam Mihir; Williams, John Robert

    2016-02-09

    An aerodynamic seal assembly for a rotary machine includes multiple sealing device segments disposed circumferentially intermediate to a stationary housing and a rotor. Each of the segments includes a shoe plate with a forward-shoe section and an aft-shoe section having multiple labyrinth teeth therebetween facing the rotor. The sealing device segment also includes multiple flexures connected to the shoe plate and to a top interface element, wherein the multiple flexures are configured to allow the high pressure fluid to occupy a forward cavity and the low pressure fluid to occupy an aft cavity. Further, the sealing device segments include a secondary seal attached to the top interface element at one first end and positioned about the flexures and the shoe plate at one second end.

  20. Turbine and Structural Seals Team Facilities

    Data.gov (United States)

    Federal Laboratory Consortium — Seals Team Facilities conceive, develop, and test advanced turbine seal concepts to increase efficiency and durability of turbine engines. Current projects include...

  1. Friction Characteristics of Mechanical Seals with Laser-textured Seal Faces

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Heat generated by friction between faces of mechanica l seals is a major factor that causes deterioration of the seals and shortens th eir service life. Excessive temperature rise can greatly alter the seal geometry and vaporize the sealing fluid, resulting in friction of boundary lubrication. These effects on face seals usually lead to excessive leakage and ultimately ren der the seal inoperable. In order to maintain the reliability of seals, high fri ction and unwanted wear must be avoided. Using the l...

  2. Chips 2020

    CERN Document Server

    2016-01-01

    The release of this second volume of CHIPS 2020 coincides with the 50th anniversary of Moore’s Law, a critical year marked by the end of the nanometer roadmap and by a significantly reduced annual rise in chip performance. At the same time, we are witnessing a data explosion in the Internet, which is consuming 40% more electrical power every year, leading to fears of a major blackout of the Internet by 2020. The messages of the first CHIPS 2020, published in 2012, concerned the realization of quantum steps for improving the energy efficiency of all chip functions. With this second volume, we review these messages and amplify upon the most promising directions: ultra-low-voltage electronics, nanoscale monolithic 3D integration, relevant-data, brain- and human-vision-inspired processing, and energy harvesting for chip autonomy. The team of authors, enlarged by more world leaders in low-power, monolithic 3D, video, and Silicon brains, presents new vistas in nanoelectronics, promising  Moore-like exponential g...

  3. 7 CFR 29.35 - Lot seal.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Lot seal. 29.35 Section 29.35 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Regulations Definitions § 29.35 Lot seal. A seal approved by the Director for sealing lots...

  4. 7 CFR 29.34 - Sample seal.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Sample seal. 29.34 Section 29.34 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Regulations Definitions § 29.34 Sample seal. A seal approved by the Director for sealing...

  5. Seal device for ferromagnetic containers

    Science.gov (United States)

    Meyer, Ross E.; Jason, Andrew J.

    1994-01-01

    A temporary seal or patch assembly prevents the escape of contents, e.g., fluids and the like, from within a container having a breach therethrough until the contents can be removed and/or a repair effected. A frame that supports a sealing bladder can be positioned over the breach and the frame is then attached to the container surface, which must be of a ferromagnet material, by using switchable permanent magnets. The permanent magnets are designed to have a first condition that is not attracted to the ferromagnetic surface and a second conditions whereby the magnets are attracted to the surface with sufficient force to support the seal assembly on the surface. Latching devices may be attached to the frame and engage the container surface with hardened pins to prevent the lateral movement of the seal assembly along the container surface from external forces such as fluid drag or gravity.

  6. Quantum String Seal Is Insecure

    CERN Document Server

    Chau, H F

    2006-01-01

    A quantum string seal encodes the value of a (bit) string as a quantum state in such a way that everyone can extract a non-negligible amount of information on the string by a suitable measurement. Moreover, such measurement must disturb the quantum state and is likely to be detected by an authorized verifier. In this way, the intactness of the encoded quantum state plays the role of a wax seal in the digital world. Here I analyze the security of quantum string seal by studying the information disturbance tradeoff of a measurement. This information disturbance tradeoff analysis extends the earlier results of Bechmann-Pasquinucci et al. and Chau by concluding that all quantum string seals are insecure. Specifically, I find a way to obtain non-trivial information on the string that escapes the verifier's detection with probability at least one half.

  7. Alaska Harbor Seal Glacial Surveys

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Floating glacial ice serves as a haul-out substrate for a significant number (10-15%) of Alaskan harbor seals, and thus surveying tidewater glacial fjords is an...

  8. Northern Fur Seal Food Habits

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains food habits samples, usually scats, collected opportunistically on northern fur seal rookeries and haulouts in Alaska from 1987 to present....

  9. Brush Seals for Improved Steam Turbine Performance

    Science.gov (United States)

    Turnquist, Norman; Chupp, Ray; Baily, Fred; Burnett, Mark; Rivas, Flor; Bowsher, Aaron; Crudgington, Peter

    2006-01-01

    GE Energy has retrofitted brush seals into more than 19 operating steam turbines. Brush seals offer superior leakage control compared to labyrinth seals, owing to their compliant nature and ability to maintain very tight clearances to the rotating shaft. Seal designs have been established for steam turbines ranging in size from 12 MW to over 1200 MW, including fossil, nuclear, combined-cycle and industrial applications. Steam turbines present unique design challenges that must be addressed to ensure that the potential performance benefits of brush seals are realized. Brush seals can have important effects on the overall turbine system that must be taken into account to assure reliable operation. Subscale rig tests are instrumental to understanding seal behavior under simulated steam-turbine operating conditions, prior to installing brush seals in the field. This presentation discusses the technical challenges of designing brush seals for steam turbines; subscale testing; performance benefits of brush seals; overall system effects; and field applications.

  10. Status of Understanding for Seal Materials

    Science.gov (United States)

    Brown, P. F.

    1984-01-01

    Material selection for mainshaft face and ring seals, labyrinth seals, accessory gearbox face seals, and lip seals are discussed in light of tribology requirements and a given seal application. Carbon graphite has been found to be one of the best sealing materials and it is widely used in current gas turbine mainshaft and accessory gearbox seals. Its popularity is due to its unique combination of properties which consists of dimensional stability, corrosion resistance, low friction, good self lubricating characteristics, high thermal conductivity and low thermal expansion, the latter two properties combining to provide good thermal shock resistance. A brief description of the seals and the requirements they must meet are discussed to provide insight into the limitations and advantages of the seals in containing the lubricant. A forecast is made of the operational requirements of main shaft and gearbox seals for advanced engines and candidate materials and coatings that may satisfy these advanced engine requirements.

  11. Grease lubrication mechanisms in bearing seals

    OpenAIRE

    2011-01-01

    Rolling bearings contain seals to keep lubricant inside and contaminants outside the bearing system. These systems are often lubricated with grease; the grease acts as a lubricant for the bearing and seal and improves the sealing efficiency. In this thesis, the influence of lubricating grease on bearing seal performance is studied. Rheological properties of the grease, i.e. shear stress and normal stress difference, are evaluated and related to the lubricating and sealing performance of the s...

  12. Harbour seals (Phoca vitulina and rehabilitation

    Directory of Open Access Journals (Sweden)

    Nynke Osinga

    2010-09-01

    Full Text Available Throughout the past few decades, rehabilitation of seals has become an activity that is anchored in the present day society of many countries. Seals are primarily rehabilitated to help individual animals in distress. At the same time, the release of seals which would have otherwise died can be considered as a contribution to the population. Most rehabilitated seals are animals under one year of age. They are mainly orphans, weaned seals with complications and seals with a parasiticbronchopneumonia. For the optimal handling of seals and their diseases, centralised operations with quality standards are essential. Rehabilitation provides an instrument to monitor the health of the seal population and its ecosystem. Changes in stranding trends or the appearance of new diseases can be monitored. Moreover, rehabilitation is important to show the general public thestate of the marine environment. In the Netherlands there is significant social support for the rehabilitation of seals. Experience obtained with seal care is of importance in countries where urgent help of threatened seal species is required. Here individual seals are also ambassadors to raise support for the protection of this species in general. Given that the anthropogenic impact on the seals and their environment is extensive in the Wadden Sea, rehabilitation centres can compensate the consequences of this impact on individual seals as well as the population as a whole.

  13. Sealing Performance of Labyrinth Seals against Small Oil Particles in HDDs

    Science.gov (United States)

    Miyatake, Masaaki; Yoshimoto, Shigeka; Dambara, Shinsuke; Nakamura, Taichi; Tanaka, Katsuhiko

    Small oil particles generated from lubricant for ball bearings in HDDs sometimes cause fatal problems such as head crashes. A labyrinth seal is often used to prevent oil particles from scattering onto the disk surfaces. In this paper, the sealing performance of labyrinth seals for small oil particles is investigated numerically and experimentally. Two types of labyrinth seal are considered, one a straight-type and the other a bent-type seal. It was found that the sealing capability of the labyrinth seal is generated by the centrifugal force exerted on oil particles due to disk rotation when they pass through the seal gap.

  14. Gas Path Sealing in Turbine Engines

    Science.gov (United States)

    Ludwig, L. P.

    1978-01-01

    A survey of gas path seals is presented with particular attention given to sealing clearance effects on engine component efficiency. The effects on compressor pressure ratio and stall margin are pointed out. Various case-rotor relative displacements, which affect gas path seal clearances, are identified. Forces produced by nonuniform sealing clearances and their effect on rotor stability are discussed qualitatively, and recent work on turbine-blade-tip sealing for high temperature is described. The need for active clearance control and for engine structural analysis is discussed. The functions of the internal-flow system and its seals are reviewed.

  15. Mechanical seal with textured sidewall

    Energy Technology Data Exchange (ETDEWEB)

    Khonsari, Michael M.; Xiao, Nian

    2017-02-14

    The present invention discloses a mating ring, a primary ring, and associated mechanical seal having superior heat transfer and wear characteristics. According to an exemplary embodiment of the present invention, one or more dimples are formed onto the cylindrical outer surface of a mating ring sidewall and/or a primary ring sidewall. A stationary mating ring for a mechanical seal assembly is disclosed. Such a mating ring comprises an annular body having a central axis and a sealing face, wherein a plurality of dimples are formed into the outer circumferential surface of the annular body such that the exposed circumferential surface area of the annular body is increased. The texture added to the sidewall of the mating ring yields superior heat transfer and wear characteristics.

  16. Cryogenic Flange and Seal Evaluation

    Science.gov (United States)

    Ramirez, Adrian

    2014-01-01

    The assembly of flanges, seals, and pipes are used to carry cryogenic fluid from a storage tank to the vehicle at launch sites. However, after a certain amount of cycles these raised face flanges with glass-filled Teflon gaskets have been found to have torque relaxation and are as a result susceptible to cryogenic fluid leakage if not re-torqued. The intent of this project is to identify alternate combinations of flanges and seals which may improve thermal cycle performance and decrease re-torque requirements. The general approach is to design a test fixture to evaluate leak characteristics between spiral and concentric serrations and to test alternate flange and seal combinations. Due to insufficient time, it was not possible to evaluate these different types of combinations for the combination that improved thermal cycle performance the most. However, the necessary drawings for the test fixture were designed and assembled along with the collection of the necessary parts.

  17. Isolation of plasma from whole blood using a microfludic chip in a continuous cross-flow

    Institute of Scientific and Technical Information of China (English)

    CHEN Xing; CUI DaFu; ZHANG LuLu

    2009-01-01

    A novel microfluidic chip is developed for crossflow filtration plasma from the whole blood which is carried out in a continuous manner. This microfluidic chip was made of a silicon substrate sealed with a compound cover. The silicon substrate fabricated by micro-electro-mechanical system (MEMS)technology consisted of microposts array, microchannels and reservoirs. Then the silicon substrate was characterized by Scaning Electron Microscopy (SEM). The performance of the microfiuidic chip was valued by the experiments of plasma isolation. During more than one hour of continuous blood infusion through the chip, there were no problems of jamming or clogging, and the plasma selectivity of 97.78% was achieved. Due to the chip's simple structure and control mechanism with a continuous,real time operating manner, this microfluidic chip is easily expected to be integrated into micro total analytical system (uTAS) which will create a microanalysis system for point-of-care diagnostics.

  18. Stabilizing geometry for hydrodynamic rotary seals

    Science.gov (United States)

    Dietle, Lannie L.; Schroeder, John E.

    2010-08-10

    A hydrodynamic sealing assembly including a first component having first and second walls and a peripheral wall defining a seal groove, a second component having a rotatable surface relative to said first component, and a hydrodynamic seal comprising a seal body of generally ring-shaped configuration having a circumference. The seal body includes hydrodynamic and static sealing lips each having a cross-sectional area that substantially vary in time with each other about the circumference. In an uninstalled condition, the seal body has a length defined between first and second seal body ends which varies in time with the hydrodynamic sealing lip cross-sectional area. The first and second ends generally face the first and second walls, respectively. In the uninstalled condition, the first end is angulated relative to the first wall and the second end is angulated relative to the second wall. The seal body has a twist-limiting surface adjacent the static sealing lip. In the uninstalled condition, the twist-limiting surface is angulated relative to the peripheral wall and varies along the circumference. A seal body discontinuity and a first component discontinuity mate to prevent rotation of the seal body relative to the first component.

  19. Legacy HMSRP Hawaiian Monk Seals Observers

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set documents observers that have collected monk seal data as part of the ongoing monk seal population assessment efforts by PSD personnel and cooperating...

  20. HMSRP Hawaiian Monk Seal Handling Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records for all handling and measurement of Hawaiian monk seals since 1981. Live seals are handled and measured during a variety of events...

  1. HMSRP Hawaiian Monk Seal Entanglement data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The data set contains records of all entanglements of Hawaiian monk seals in marine debris. The data set comprises records of seals entangled by derelict fishing...

  2. Film riding seals for rotary machines

    Energy Technology Data Exchange (ETDEWEB)

    Bidkar, Rahul Anil; Sarawate, Neelesh Nandkumar; Wolfe, Christopher Edward; Ruggiero, Eric John; Raj Mohan, Vivek Raja

    2017-03-07

    A seal assembly for a rotary machine is provided. The seal assembly includes multiple sealing device segments disposed circumferentially intermediate to a stationary housing and a rotor. Each of the segments includes a shoe plate with a forward-shoe section and an aft-shoe section having one or more labyrinth teeth therebetween facing the rotor. The sealing device includes a stator interface element having a groove or slot for allowing disposal of a spline seal for preventing segment leakages. The sealing device segment also includes multiple bellow springs or flexures connected to the shoe plate and to the stator interface element. Further, the sealing device segments include a secondary seal integrated with the stator interface element at one end and positioned about the multiple bellow springs or flexures and the shoe plate at the other end.

  3. Legacy HMSRP Hawaiian Monk Seal Ultrasound Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Ultrasounds measuring the condition of juvenile seals at Laysan Island during 2009-2010, collected when seals were handled as part of the De-Worming Project

  4. Multi-layer seal for electrochemical devices

    Science.gov (United States)

    Chou, Yeong-Shyung [Richland, WA; Meinhardt, Kerry D [Kennewick, WA; Stevenson, Jeffry W [Richland, WA

    2010-09-14

    Multi-layer seals are provided that find advantageous use for reducing leakage of gases between adjacent components of electrochemical devices. Multi-layer seals of the invention include a gasket body defining first and second opposing surfaces and a compliant interlayer positioned adjacent each of the first and second surfaces. Also provided are methods for making and using the multi-layer seals, and electrochemical devices including said seals.

  5. Multi-layer seal for electrochemical devices

    Science.gov (United States)

    Chou, Yeong-Shyung [Richland, WA; Meinhardt, Kerry D [Kennewick, WA; Stevenson, Jeffry W [Richland, WA

    2010-11-16

    Multi-layer seals are provided that find advantageous use for reducing leakage of gases between adjacent components of electrochemical devices. Multi-layer seals of the invention include a gasket body defining first and second opposing surfaces and a compliant interlayer positioned adjacent each of the first and second surfaces. Also provided are methods for making and using the multi-layer seals, and electrochemical devices including said seals.

  6. Predicting Leakage in Labyrinth Seals

    Science.gov (United States)

    Morrison, G. L.; Rhode, D. L.; Cogan, K. C.; Chi, D.; Demko, J.

    1985-01-01

    Analytical and empirical methods evaluated. 264-page report presents comprehensive information on leakage in labyrinth seals. Summarizes previous analyses of leakage, reviews leakage tests conducted by authors and evaluates various analytical and experimental methods of determining leakage and discusses leakage prediction techniques.

  7. Pre-sealing risk analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ensminger, D.A.; Hough, M.E.; Oston, S.G.

    1980-01-07

    This report describes studies of accidents involving high-level radioactive waste before sealing the waste into a repository. The report summarizes work done in this area during Fiscal Year 1978 and supplements previous work. Models of accident probability, severity, and consequences are refined and extended.

  8. Aerodynamic seal assemblies for turbo-machinery

    Energy Technology Data Exchange (ETDEWEB)

    Bidkar, Rahul Anil; Wolfe, Christopher; Fang, Biao

    2015-09-29

    The present application provides an aerodynamic seal assembly for use with a turbo-machine. The aerodynamic seal assembly may include a number of springs, a shoe connected to the springs, and a secondary seal positioned about the springs and the shoe.

  9. Piston rod seal for a Stirling engine

    Science.gov (United States)

    Shapiro, Wilbur

    1984-01-01

    In a piston rod seal for a Stirling engine, a hydrostatic bearing and differential pressure regulating valve are utilized to provide for a low pressure differential across a rubbing seal between the hydrogen and oil so as to reduce wear on the seal.

  10. Ergonomics and safety of manual bag sealing.

    NARCIS (Netherlands)

    Groot, M.D. de; Bosch, T.; Eikhout, S.M.; Vink, P.

    2005-01-01

    A variety of seals is used to close bags. Each seal has advantages and disadvantages. For shop assistants sealing bags could be a repetitive physically demanding action. Opening and closing the bags again can cause some discomfort or annoyance for consumers. Besides, it is an activity which can enda

  11. Annular Pressure Seals and Hydrostatic Bearings

    Science.gov (United States)

    2006-11-01

    affecting the rotordynamics of liquid turbopumps, in particular those handling large density fluids. Highlights on the bulk-flow analysis of annular seals... rotordynamic stability. Hydrostatic bearings rely on external fluid pressurization to generate load support and large centering stiffnesses, even in...SEALS IN PUMP APPLICATIONS Seal rotordynamic characteristic have a primary influence on the stability response of high-performance turbomachinery [1

  12. Characteristics of a magnetic fluid seal and its motion in an axial variable seal gap

    Institute of Scientific and Technical Information of China (English)

    QIAN Ji-guo; YANG Zhi-yi

    2008-01-01

    With suitable assumptions a hydrodynamic model for the magnetic fluid motion in an axial variable gap seal was constructed, and the solution to the equations of the model was deduced. The characteristics of a magnetic fluid seal and its motion,including the speed and pressure distribution, and the seal capacity of a magnetic fluid rotating seal were systematically described.The factors affecting seal capacity and ways to improve seal capacity based on the hydrodynamic model are discussed. The basic condition for dynamic seal availability is presented. The rotating speed and radius of the shafts should be decreased. The work can provide proof of a seal design or suggest ways to improve the seal capacity of magnetic fluid seals.

  13. Symmetries in Images on Ancient Seals

    CERN Document Server

    Sparavigna, Amelia

    2008-01-01

    In this paper, we discuss the presence of symmetries in images engraved on ancient seals, in particular on stamp seals. Mainly used to secure the containers from tampering and for owner's identification, these objects appeared during the 5th millennium BC in Mesopotamia. Usually the seals were engraved with simple images, suitable to communicate an immediate information. Rotational symmetries are already displayed by the most ancient stamp seals, whose images reach a quasi-perfect symmetry in their small circular or ovoid spaces. Bilateral symmetries are quite common in Egyptian scarab seals.

  14. Rotary seal with improved film distribution

    Energy Technology Data Exchange (ETDEWEB)

    Dietle, Lannie Laroy; Schroeder, John Erick

    2015-09-01

    The present invention is a generally circular rotary seal that establishes sealing between relatively rotatable machine components for lubricant retention and environmental exclusion, and incorporates seal geometry that interacts with the lubricant during relative rotation to distribute a lubricant film within the dynamic sealing interface. The features of a variable inlet size, a variable dynamic lip flank slope, and a reduction in the magnitude and circumferentially oriented portion of the lubricant side interfacial contact pressure zone at the narrowest part of the lip, individually or in combination thereof, serve to maximize interfacial lubrication in severe operating conditions, and also serve to minimize lubricant shear area, seal torque, seal volume, and wear, while ensuring retrofitability into the seal grooves of existing equipment.

  15. Rotary seal with improved film distribution

    Science.gov (United States)

    Dietle, Lannie Laroy; Schroeder, John Erick

    2013-10-08

    The present invention is a generally circular rotary seal that establishes sealing between relatively rotatable machine components for lubricant retention and environmental exclusion, and incorporates seal geometry that interacts with the lubricant during relative rotation to distribute a lubricant film within the dynamic sealing interface. The features of a variable inlet size, a variable dynamic lip flank slope, and a reduction in the magnitude and circumferentially oriented portion of the lubricant side interfacial contact pressure zone at the narrowest part of the lip, individually or in combination thereof, serve to maximize interfacial lubrication in severe operating conditions, and also serve to minimize lubricant shear area, seal torque, seal volume, and wear, while ensuring retrofitability into the seal grooves of existing equipment.

  16. Seal dynamics on the Swedish west coast: Scenarios of competition as Baltic grey seal intrude on harbour seal territory

    Science.gov (United States)

    Svensson, Carl Johan

    2012-07-01

    The Kattegat-Skagerrak region on the Swedish west coast is home to an abundant harbour seal population (Phoca vitulina) and a small scattered grey seal population (Halichoerus grypus). In addition, grey seal from the growing population in the Baltic Sea frequently migrate into the Kattegat-Skagerrak. Harbour seals on the west coast of Sweden show relatively high population growth (approximately 9%) compared to the Baltic grey seal in ice-free habitats (approximately 6%), which, in theory, makes harbour seal the stronger competitor of the two in this region. However, incidents of disease in harbour seals that lower population growth are becoming more frequent. These epidemics are primarily caused by the Phocine Distemper Virus (PDV), and may reduce population size with up to 70%. This study models the average development under potential scenarios of competing harbour- and Baltic grey seal populations using Leslie matrices and the Lotka-Volterra model of inter-specific competition. The model is parameterised with previously published data, and resource overlap is incorporated through density dependent pup survival. Using numerical methods short- and long-term abundances are simulated under weak, moderate and strong competition and for different frequencies of PDV epidemics. Results show that the harbour seals are resilient to competition while exerting a negative effect on grey seal abundance under moderate to strong competition. Hence Baltic grey seal benefit from weaker levels of competition. Under moderate and strong competition grey seal abundance is a direct function of the PDV frequency as this reduces the competitive strength of harbour seals. Theoretically this means that higher frequencies of PDV or other pathogens epidemics could facilitate an expansion of Baltic grey seal into Kattegat-Skagerrak. Independent of interaction strength and frequency of epidemics the projected changes to abundances are slow (50-100 years), and even in exceedingly stable

  17. Mechanical Deformation of Ship Stern-Shaft Mechanical Face Seals

    Institute of Scientific and Technical Information of China (English)

    朱汉华; 刘正林; 温诗铸; 严新平

    2004-01-01

    In ship propeller shaft systems, the shaft seal is a mechanical face seal, which includes a stationary metal seal ring and a rotating ring.The seal faces are deformed with different loads.The deformation of the seal faces affects the performance of mechanical face seals, which leads to water leakage, so the seal face deformation must be analyzed.A mechanics model with deformation equations was developed to describe ship stern-shaft seals.An example was given to verify the deformation equations.The solution of the deformation equations gives a theoretical basis for the analysis of seal leakage and improvements of seal structures.

  18. Fully integrated optical system for lab-on-a-chip applications

    DEFF Research Database (Denmark)

    Balslev, Søren; Olsen, Brian Bilenberg; Geschke, Oliver

    2004-01-01

    We present a lab-on-a-chip device featuring a microfluidic dye laser, wave-guides, microfluidic components and photo-detectors integrated on the chip. The microsystem is designed for wavelength selective absorption measurements in the visible range on a fluidic sample, which can be prepared....../mixed on-chip. The laser structures, wave-guides and micro-fluidic handling system are defined in a single UV-lithography step on a 10 μm thick SU-8 layer on top of the substrate. The SU-8 structures are sealed by a Borofloat glass lid, using polymethylmethacrylate (PMMA) adhesive bonding....

  19. Hermetic seal for a shaft

    Science.gov (United States)

    Lombardi, F. (Inventor)

    1982-01-01

    An hermetic seal for a linear rod having a portion thereof projected axially through a port defined in a wall for a pressure chamber and supported thereby for omni-directional motion is described. The seal is characterized by a resilient, impervious, cylindrical body having a first section concentrically related to the shaft and integrally affixed thereto comprising a linear ordered array of annular flutes. A second section integrally is affixed to the wall of the chamber and concentrically related to the port comprising a second linear ordered array of annular flutes. A third section is interposed between the first and second sections and integrally affixed in coaxial alignment therewith comprising an annular ordered array of linear flutes concentrically related to the shaft, whereby axial, angular, and pivotal motion of the rod is accommodated.

  20. Design optimization of seal structure for sealing liquid by magnetic fluids

    Science.gov (United States)

    Liu, Tonggang; Cheng, Yusheng; Yang, Zhiyi

    2005-03-01

    The durability of the magnetic fluid seal clearly decreases when sealing another liquid because of the interface instability caused by the applied magnetic field and the velocity difference of the two liquids. With an intention to establish a stable interface during sealing liquid, a new magnetic fluid seal was developed in this paper. The parameters of the structure were optimized by a simulation apparatus. And the magnetic fluid seal designed based on the optimum parameters shows good performance and long life for sealing lubricating oil.

  1. Numerical Analysis of Magnetic Fluid Sealing Performance

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The sealing performance of magnetic fluid is related to the magnetic fluid itself. Many factors can influence the magnetic field and the seal pressure differences of magnetic fluid seals, such as the sealing gap, the shaft eccentricity, the shaft diameter, the volume of the magnetic fluid and the centrifugal force. These factors are analyzed by numerical computation . When the seal material and structure are the same, the seal pressure difference is directly proportional to the magnetic field intensity and the saturation magnetization of the magnetic fluid. The sealing performance of the magnetic fluid will reduce with the increase of the sealing gap and shaft eccentricity. The sealing performance will increase with the volume of the magnetic fluid and decrease with the increase of the shaft diameter taking gravity into account. The increase of the shaft diameter is the same as the reduction of the volume of the magnetic fluid. The magnetic fluid cross-section can change because of the centrifugal force. Some improvements can reduce the influence of the centrifugal force. The centrifugal force can be utilized to improve the sealing performance.

  2. Coalbed methane reservoir boundaries and sealing mechanism

    Institute of Scientific and Technical Information of China (English)

    SU Xianbo; LIN Xiaoying; LIU Shaobo; SONG Yan

    2005-01-01

    It is important to investigate the coalbed methane reservoir boundaries for the classification, exploration, and development of the coalbed methane reservoir.Based on the investigation of the typical coalbed methane reservoirs in the world, the boundaries can be divided into four types: hydrodynamic boundary, air altered boundary,permeability boundary, and fault boundary. Hydrodynamic and air altered boundaries are ubiquitous boundaries for every coalbed methane reservoir. The four types of the fault sealing mechanism in the petroleum geological investigation (diagen- esis, clay smear, juxtaposition and cataclasis) are applied to the fault boundary of the coalbed methane reservoir. The sealing mechanism of the open fault boundary is the same with that of the hydrodynamic sealing boundary.The sealing mechanism of the permeability boundary is firstly classified into capillary pressure sealing and hydrocarbon concentration sealing. There are different controlling boundaries in coalbed methane reservoirs that are in different geological backgrounds. Therefore, the coalbed methane reservoir is diversiform.

  3. Air riding seal for a turbine

    Energy Technology Data Exchange (ETDEWEB)

    Mills, Jacob A; Brown, Wesley D; Sexton, Thomas D; Jones, Russell B

    2016-07-19

    An air riding seal between a rotor and a stator in a turbine of a gas turbine engine, where an annular piston is movable in an axial direction within a housing that extends from the stator, and a bellows is secured to the annular piston to form a flexible air passageway from a compressed air inlet through the annular piston and into a cushion cavity that forms an air riding seal between the annular piston and the rotor sealing surface. In another embodiment, a flexible seal secured to and extending from the annular piston forms a sealing surface between the annular piston chamber and the annular piston to provide a seal and allow for axial movement.

  4. NEW POLIMER SEALING FLUID STOPS MUD LOSS

    Directory of Open Access Journals (Sweden)

    Stanislaw Stryczek

    1989-12-01

    Full Text Available This paper deals with a composition of sealing fluid, prepared from acrylic acid salt water solution Solakryl M. Laboratory test results of technological properties of its modifications with mineral agents are shown. A new method of sealing mud loss operations with given sealing liquid is discussed along with comments on effects of its use for stopping mud loss in case of freeze-well drilling is described (the paper is published in Croatian.

  5. A novel approach on fluid dispensing for a DNA/RNA extraction chip package

    Science.gov (United States)

    Xie, Ling; Premachandran, C. S.; Chew, Michelle; Yao, Qiang; Xu, Diao; Pinjala, D.

    2008-02-01

    Micro fluidic package with integrated reservoirs has been developed for DNA /RNA extraction application. A membrane based pump which consists of a reservoir to store reagents and a pin valve to control the fluid is developed to dispense the reagents into the chip. A programmable external actuator is fabricated to dispense the fluid from the membrane pump into the DNA chip. An elastic and high elongation thin rubber membrane is used to seal the membrane pump and at the same time prevent actuator from mixing with different reagents in the micro fluidic package. Break displacement during actuation of membrane pump sealing material is studied with different ratios of PDMS and other types of rubber materials. The fluid flow from the reservoir to the chip is controlled by a pin valve which is activated during the external actuation. A CFD simulation is performed to study the pumping action dusting the external actuation and is validated with experimental results.

  6. Influence of Rocket Engine Characteristics on Shaft Sealing Technology Needs

    Science.gov (United States)

    Keba, John E.

    1999-01-01

    This paper presents viewgraphs of The Influence of Rocket Engine Characteristics on Shaft Sealing Technology Needs. The topics include: 1) Rocket Turbomachinery Shaft Seals (Inter-Propellant-Seal (IPS) Systems, Lift-off Seal Systems, and Technology Development Needs); 2) Rocket Engine Characteristics (Engine cycles, propellants, missions, etc., Influence on shaft sealing requirements); and 3) Conclusions.

  7. A reliable sealing method for microbatteries

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yuxing; Cartmell, Samuel; Li, Qiuyan; Xiao, Jie; Li, Huidong; Deng, Zhiqun Daniel; Zhang, Ji-Guang

    2017-02-01

    With continuous downsizing of electronic devices, lithium batteries of traditional shapes cannot meet the demand where small-size high energy density batteries are needed. Conventional sealing methods become increasingly difficult to apply and impose high processing cost as the size of batteries decreases. In this report, a facile sealing method is proposed and demonstrated in CFx/Li mini-batteries. The method employs a temporary barrier to liquid electrolytes while relies on the epoxies/cell casings bond for the hermetic sealing. Cells sealed by this method show no degradation for an extended period of storage time.

  8. Self-acting geometry for noncontact seals

    Science.gov (United States)

    Allen, G. P.

    1981-01-01

    Performance ot two self acting seal designs for a liquid oxygen (LOX) turbopump was predicted over ranges of pressure differential and speed. Predictions were compared with test results. Performance of a radial face seal for LOX was predicted up to 448 N/cu cm and 147 m/sec. Performance of a segmented circumferential seal for helium was predicted up to 69 N/cu cm and 189 m/sec. Results confirmed predictions of noncontact operation. Qualitative agreement between test and analysis was found. The LOX face seal evidently operated with mostly liquid in the self acting geometry and mostly gas across the dam.

  9. Byzantine seals from the Ras fortress

    Directory of Open Access Journals (Sweden)

    Ivanišević Vujadin

    2013-01-01

    Full Text Available In this paper, seals found at the location of the Ras fortress (Tvrđava Ras have been published. Inscriptions on these seals show that they used to belong to persons which could be identified with certain military commanders who served under Alexios I Komnenos. The seals in question are: the seals of protonobelissimos Eustathios Kamytzes, Constantine Dalassenos Doukas, protoproedros and doux Constantine Kekaumenos and a certain person called Alexios. [Projekat Ministarstva nauke Republike Srbije, br. 177021 i br. 177032

  10. Pixel detector readout chip

    CERN Multimedia

    1991-01-01

    Close-up of a pixel detector readout chip. The photograph shows an aera of 1 mm x 2 mm containing 12 separate readout channels. The entire chip contains 1000 readout channels (around 80 000 transistors) covering a sensitive area of 8 mm x 5 mm. The chip has been mounted on a silicon detector to detect high energy particles.

  11. Well sealing via thermite reactions

    Energy Technology Data Exchange (ETDEWEB)

    Lowry, William Edward; Dunn, Sandra Dalvit

    2016-11-15

    A platform is formed in a well below a target plug zone by lowering a thermite reaction charge into the well and igniting it, whereby the products of the reaction are allowed to cool and expand to form a platform or support in the well. A main thermite reaction charge is placed above the platform and ignited to form a main sealing plug for the well. In some embodiments an upper plug is formed by igniting an upper thermite reaction charge above the main thermite reaction charge. The upper plug confines the products of ignition of the main thermite reaction charge.

  12. Magnetohydrodynamic (MHD) channel corner seal

    Science.gov (United States)

    Spurrier, Francis R.

    1980-01-01

    A corner seal for an MHD duct includes a compressible portion which contacts the duct walls and an insulating portion which contacts the electrodes, sidewall bars and insulators. The compressible portion may be a pneumatic or hydraulic gasket or an open-cell foam rubber. The insulating portion is segmented into a plurality of pieces of the same thickness as the electrodes, insulators and sidewall bars and aligned therewith, the pieces aligned with the insulator being of a different size from the pieces aligned with the electrodes and sidewall bars to create a stepped configuration along the corners of the MHD channel.

  13. Sealed nickel-cadmium battery

    Energy Technology Data Exchange (ETDEWEB)

    1989-08-15

    Overcharge protection, and especially the chargeability of a sealed Ni/Cd battery with high currents is improved by rolling a carbon-containing powdered material into the surface of the negative electrode, which material catalyzes the reduction of oxygen. Wetting of the electrode with a Tylose dispersion prior to application of the powder (by powdering, vibration or in an agitator) improves the adhesion of the powder. The cadmium electrode thus prepared combines in itself the functions of a negative principal electrode and of an auxiliary oxygen electrode.

  14. Albinistic common seals (Phoca vitulina) and melanistic grey seals (Halichoerus grypus) rehabilitated in the Netherlands

    NARCIS (Netherlands)

    Osinga, Nynke; 't Hart, Pieter; Vader, Pieter C. van Voorst

    2010-01-01

    The Seal Rehabilitation and Research Centre (SRRC) in Pieterburen, The Netherlands, rehabilitates seals from the waters of the Wadden Sea, North Sea and Southwest Delta area. Incidental observations of albinism and melanism in common and grey seals are known from countries surrounding the North Sea.

  15. Seals at sea: modelling seal distribution in the German bight based on aerial survey data

    NARCIS (Netherlands)

    Herr, H.; Scheidat, M.; Lehnert, K.; Siebert, U.

    2009-01-01

    The Wadden Sea is an important habitat for harbour seals and grey seals. They regularly haul-out on sandbanks and islands along the coast. Comparably little is known about the time seals spend at sea and how they use the remainder of the North Sea. Yet, human activity in offshore waters is increasin

  16. Corkscrew Seals: Grey Seal (Halichoerus grypus) Infanticide and Cannibalism May Indicate the Cause of Spiral Lacerations in Seals

    Science.gov (United States)

    2016-01-01

    Large numbers of dead seals with characteristic spiral lesions have been washing ashore around the North Atlantic over the past two decades. Interactions with ship propellers and shark predation have been suggested as the likely causal mechanisms. However, new evidence points towards a more likely candidate: grey seal predation. An adult male grey seal was observed and recorded catching, killing and eating five weaned grey seal pups over a period of one week on the Isle of May, Scotland. A further 9 carcasses found in the same area exhibited similar injuries. Post mortem analysis of lesions indicated the wound characteristics were similar to each other and in 12 of the 14 carcasses analysed, were indistinguishable from carcasses previously attributed to propeller interaction. We therefore propose that most of the seal carcasses displaying spiral lacerations in the UK are caused by grey seal predation. Cases in other locations should be re-evaluated using the scoring system presented here to identify whether grey seal predation is a major cause of mortality in phocid seals. PMID:27254025

  17. Corkscrew Seals: Grey Seal (Halichoerus grypus Infanticide and Cannibalism May Indicate the Cause of Spiral Lacerations in Seals.

    Directory of Open Access Journals (Sweden)

    Andrew Brownlow

    Full Text Available Large numbers of dead seals with characteristic spiral lesions have been washing ashore around the North Atlantic over the past two decades. Interactions with ship propellers and shark predation have been suggested as the likely causal mechanisms. However, new evidence points towards a more likely candidate: grey seal predation. An adult male grey seal was observed and recorded catching, killing and eating five weaned grey seal pups over a period of one week on the Isle of May, Scotland. A further 9 carcasses found in the same area exhibited similar injuries. Post mortem analysis of lesions indicated the wound characteristics were similar to each other and in 12 of the 14 carcasses analysed, were indistinguishable from carcasses previously attributed to propeller interaction. We therefore propose that most of the seal carcasses displaying spiral lacerations in the UK are caused by grey seal predation. Cases in other locations should be re-evaluated using the scoring system presented here to identify whether grey seal predation is a major cause of mortality in phocid seals.

  18. Cross-amplification and validation of SNPs conserved over 44 million years between seals and dogs.

    Directory of Open Access Journals (Sweden)

    Joseph I Hoffman

    Full Text Available High-density SNP arrays developed for humans and their companion species provide a rapid and convenient tool for generating SNP data in closely-related non-model organisms, but have not yet been widely applied to phylogenetically divergent taxa. Consequently, we used the CanineHD BeadChip to genotype 24 Antarctic fur seal (Arctocephalus gazella individuals. Despite seals and dogs having diverged around 44 million years ago, 33,324 out of 173,662 loci (19.2% could be genotyped, of which 173 were polymorphic and clearly interpretable. Two SNPs were validated using KASP genotyping assays, with the resulting genotypes being 100% concordant with those obtained from the high-density array. Two loci were also confirmed through in silico visualisation after mapping them to the fur seal transcriptome. Polymorphic SNPs were distributed broadly throughout the dog genome and did not differ significantly in proximity to genes from either monomorphic SNPs or those that failed to cross-amplify in seals. However, the nearest genes to polymorphic SNPs were significantly enriched for functional annotations relating to energy metabolism, suggesting a possible bias towards conserved regions of the genome.

  19. Space Environment Effects on Silicone Seal Materials

    Science.gov (United States)

    deGroh, Henry C., III; Daniels, Christopher C.; Dever, Joyce A.; Miller, Sharon K.; Waters, Deborah L.; Finkbeiner, Joshua R.; Dunlap, Patrick H.; Steinetz, Bruce M.

    2010-01-01

    A docking system is being developed by the NASA to support future space missions. It is expected to use redundant elastomer seals to help contain cabin air during dockings between two spacecraft. The sealing surfaces are exposed to the space environment when vehicles are not docked. In space, the seals will be exposed to temperatures between 125 to -75 C, vacuum, atomic oxygen, particle and ultraviolet radiation, and micrometeoroid and orbital debris (MMOD). Silicone rubber is the only class of space flight-qualified elastomeric seal material that functions across the expected temperature range. NASA Glenn has tested three silicone elastomers for such seal applications: two provided by Parker (S0899-50 and S0383-70) and one from Esterline (ELA-SA-401). The effects of atomic oxygen (AO), UV and electron particle radiation, and vacuum on the properties of these three elastomers were examined. Critical seal properties such as leakage, adhesion, and compression set were measured before and after simulated space exposures. The S0899-50 silicone was determined to be inadequate for extended space seal applications due to high adhesion and intolerance to UV, but both S0383-70 and ELA-SA-401 seals were adequate.

  20. Space Environment's Effects on Seal Materials

    Science.gov (United States)

    deGroh, Henry C., III; Daniels, Christopher C.; Dunlap, Patrick; Miller, Sharon; Dever, Joyce; Waters, Deborah; Steinetz, Bruce M.

    2007-01-01

    A Low Impact Docking System (LIDS) is being developed by the NASA Johnson Space Center to support future missions of the Crew Exploration Vehicle (CEV). The LIDS is androgynous, such that each system half is identical, thus any two vehicles or modules with LIDS can be coupled. Since each system half is a replica, the main interface seals must seal against each other instead of a conventional flat metal surface. These sealing surfaces are also expected to be exposed to the space environment when vehicles are not docked. The NASA Glenn Research Center (NASA GRC) is supporting this project by developing the main interface seals for the LIDS and determining the durability of candidate seal materials in the space environment. In space, the seals will be exposed to temperatures of between 50 to 50 C, vacuum, atomic oxygen, particle and ultraviolet radiation, and micrometeoroid and orbital debris (MMOD). NASA GRC is presently engaged in determining the effects of these environments on our candidate elastomers. Since silicone rubber is the only class of seal elastomer that functions across the expected temperature range, NASA GRC is focusing on three silicone elastomers: two provided by Parker Hannifin (S0-899-50 and S0-383-70) and one from Esterline Kirkhill (ELA-SA-401). Our results from compression set, elastomer to elastomer adhesion, and seal leakage tests before and after various simulated space exposures will be presented.

  1. 19 CFR 101.7 - Customs seal.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Customs seal. 101.7 Section 101.7 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY GENERAL PROVISIONS § 101.7 Customs seal. (a) Design. According to the design furnished by the...

  2. Earlier pupping in harbour seals, Phoca vitulina

    NARCIS (Netherlands)

    Reijnders, P.J.H.; Brasseur, S.M.J.M.; Meesters, H.W.G.

    2010-01-01

    The annual reproductive cycle of most seal species is characterized by a tight synchrony of births. Typically, timing of birth shows little inter-annual variation. Here, however we show that harbour seals Phoca vitulina from the Wadden Sea (southeast North Sea) have shortened their yearly cycle, mov

  3. Active Infrared Thermography for Seal Contamination Detection in Heat-Sealed Food Packaging

    Directory of Open Access Journals (Sweden)

    Karlien D’huys

    2016-11-01

    Full Text Available Packaging protects food products from environmental influences, assuring quality and safety throughout shelf life if properly performed. Packaging quality depends on the quality of the packaging material and of the closure or seal. A common problem possibly jeopardizing seal quality is the presence of seal contamination, which can cause a decreased seal strength, an increased packaging failure risk and leak formation. Therefore, early detection and removal of seal contaminated packages from the production chain is crucial. In this work, a pulsed-type active thermography method using the heated seal bars as an excitation source was studied for detecting seal contamination. Thermal image sequences of contaminated seals were recorded shortly after sealing. The detection performances of six thermal image processing methods, based on a single frame, a fit of the cooling profiles, thermal signal reconstruction, pulsed phase thermography, principal component thermography and a matched filter, were compared. High resolution digital images served as a reference to quantify seal contamination, and processed thermal images were mapped to these references. The lowest detection limit (equivalent diameter 0.60 mm was obtained for the method based on a fit of the cooling profiles. Moreover, the detection performance of this method did not depend strongly on the time after sealing at which recording of the thermal images was started, making it a robust and generally applicable method.

  4. Grey seal (Halichoerus grypus) predation on harbour seals (Phoca vitulina) on the island of Helgoland, Germany

    Science.gov (United States)

    van Neer, Abbo; Jensen, Lasse Fast; Siebert, Ursula

    2015-03-01

    The prey spectrum of grey seals has to date been described as largely consisting of different fish, cephalopod and shrimp species. On the German island of Helgoland Düne, where harbour seals (Phoca vitulina) and grey seals (Halichoerus grypus) co-occur, a young male grey seal was observed in 2013 and again in 2014 preying upon young harbour seals. A harbour seal carcass with severe traumatic lesions was retrieved and post-mortem examinations were performed. In the following weeks several carcasses showing similar lesions were found. Sightings of grey seals assumed to be preying on harbour porpoises have increased around the North Sea. Increased competition as well as individualised behaviour could explain the increased number of observations, but former cases of abnormal lesions of marine mammals attributed to for example predation by sharks or mechanical processes should be revisited with regard to the emerging knowledge.

  5. [Methods for sealing of corneal perforations].

    Science.gov (United States)

    Samoilă, O; Totu, Lăcrămioara; Călugăru, M

    2012-01-01

    A variety of corneal pathology can lead to corneal ulcers and perforations. A deep corneal ulcer may need surgical treatment to allow good volume restoration and reepithelisation. Corneal perforation must be sealed and when the perforation is large, the task of repairing the defect can be underwhelming. The elegant solution is the corneal transplant, but this is not always readily available, especially in undeveloped countries. We present here two cases with different solutions to seal the perforated cornea: the first one has a large peripheral defect and it is successfully sealed with scleral patch and the second one is central with small perforation and is successfully sealed with multilayered amniotic membrane. Both cases are followed for over 12 months and demonstrate good corneal restoration (both on clinical examination and corneal topography). Sclera and amniotic membrane can be used to seal corneal defects when corneal transplant is not readily available.

  6. Film riding seal assembly for turbomachinery

    Energy Technology Data Exchange (ETDEWEB)

    Bidkar, Rahul Anil; Giametta, Andrew Paul; Gibson, Nathan Evan McCurdy; Cleveland, Nicolas Joseph

    2016-06-07

    An aerodynamic seal assembly for a rotary machine includes multiple sealing segments disposed circumferentially intermediate to a stationary housing and a rotor. Each of the segments includes a shoe plate with a forward load-bearing section and an aft load-bearing section configured to generate an aerodynamic force between the shoe plate and the rotor. The shoe plate includes at least one labyrinth teeth facing the rotor and positioned between the forward load-bearing section and the aft load-bearing section. The sealing segment also includes at least one spring connected to a pedestal located about midway of an axial length of the shoe plate and to a stator interface element. Further, the sealing segment includes a rigid segmented secondary seal attached to the stator interface element at one first end and in contact with the pedestal of the shoe plate at one second end.

  7. A reliable sealing method for microbatteries

    Science.gov (United States)

    Wang, Yuxing; Cartmell, Samuel; Li, Qiuyan; Xiao, Jie; Li, Huidong; Deng, Zhiqun Daniel; Zhang, Ji-Guang

    2017-02-01

    As electronic devices continue to become smaller, their energy sources (i.e., batteries) also need to be smaller. Typically, energy densities of batteries decrease as the battery size decreases due to the relative increase of parasitic weight such as packaging materials. In addition, the sealing methods in conventional batteries are difficult to apply to microbatteries. In this work, we developed a facile sealing method for microbatteries. The method employs a dual-sealing concept: a first rubber barrier temporally confines the organic electrolytes and a second adhesive barrier forms a hermetic seal with the battery case. With this innovative sealing approach, excellent shelf life and operation life of the batteries have been demonstrated. A minimal amount of packing materials is employed resulting in high energy densities.

  8. Does the seal licensing system in Scotland have a negative impact on seal welfare?

    Directory of Open Access Journals (Sweden)

    Laetitia Nunny

    2016-08-01

    Full Text Available This study examined the licensing system that permits seal shooting in Scotland, which was established under Part 6 Conservation of Seals of the Marine (Scotland Act 2010. Four approaches were used: data were collated and analyzed from both the Scottish Government and Scottish Marine Animal Stranding Scheme; a survey was sent to current license holders and informal interviews were conducted with key stakeholder types. Between February 2011 and the end of October 2015, 1229 gray seals and 275 common seals were reported shot under license to the Scottish Government. The numbers of seals reported as shot has reduced year-on-year since the licensing system was put in place. While some license holders, notably fish farms, were using some non-lethal forms of deterrent to reduce seal-related damage, these were often used alongside seal shooting. Of the seals reported as shot to the Scottish Government, only a small percentage were also reported to the Scottish Marine Animal Stranding Scheme, despite this being a licensing requirement. Only 2.3% of the shot gray seals and 4.5% of the shot common seals were necropsied. There is evidence from these necropsies that some seals had not died instantly or had not been shot in the manner recommended by the Scottish Seal Management Code of Practice. These preliminary results show that more carcasses need to be recovered and necropsied if the welfare implications of current seal shooting practice are to be properly assessed. The current legislation does not specify closed seasons to protect breeding seals and thirty-five per cent of necropsied seals were pregnant gray seals. Seals have also been shot during their lactation periods when pups are dependent on their mothers. This raises significant welfare concerns. The re-introduction of closed seasons specific to each species of seal is recommended along with greater effort to deploy non-lethal methods. Independent assessment of the number of seals being killed

  9. CHIP Reporting in the CPS

    Data.gov (United States)

    U.S. Department of Health & Human Services — CHIP reporting in the CPS is unreliable. Only 10 to 30 percent of those with CHIP (but not Medicaid) report this type of coverage in the CPS. Many with CHIP report...

  10. Ocean climate and seal condition

    Directory of Open Access Journals (Sweden)

    Crocker Daniel E

    2005-03-01

    Full Text Available Abstract Background The condition of many marine mammals varies with fluctuations in productivity and food supply in the ocean basin where they forage. Prey is impacted by physical environmental variables such as cyclic warming trends. The weaning weight of northern elephant seal pups, Mirounga angustirostris, being closely linked to maternal condition, indirectly reflects prey availability and foraging success of pregnant females in deep waters of the northeastern Pacific. The aim of this study was to examine the effect of ocean climate on foraging success in this deep-diving marine mammal over the course of three decades, using cohort weaning weight as the principal metric of successful resource accrual. Results The mean annual weaning weight of pups declined from 1975 to the late 1990s, a period characterized by a large-scale, basin-wide warm decadal regime that included multiple strong or long-duration El Niños; and increased with a return to a cool decadal regime from about 1999 to 2004. Increased foraging effort and decreased mass gain of adult females, indicative of reduced foraging success and nutritional stress, were associated with high ocean temperatures. Conclusion Despite ranging widely and foraging deeply in cold waters beyond coastal thermoclines in the northeastern Pacific, elephant seals are impacted significantly by ocean thermal dynamics. Ocean warming redistributes prey decreasing foraging success of females, which in turn leads to lower weaning mass of pups. Annual fluctuations in weaning mass, in turn, reflect the foraging success of females during the year prior to giving birth and signals changes in ocean temperature cycles.

  11. Chip Multithreaded Consistency Model

    Institute of Scientific and Technical Information of China (English)

    Zu-Song Li; Dan-Dan Huan; Wei-Wu Hu; Zhi-Min Tang

    2008-01-01

    Multithreaded technique is the developing trend of high performance processor. Memory consistency model is essential to the correctness, performance and complexity of multithreaded processor. The chip multithreaded consistency model adapting to multithreaded processor is proposed in this paper. The restriction imposed on memory event ordering by chip multithreaded consistency is presented and formalized. With the idea of critical cycle built by Wei-Wu Hu, we prove that the proposed chip multithreaded consistency model satisfies the criterion of correct execution of sequential consistency model. Chip multithreaded consistency model provides a way of achieving high performance compared with sequential consistency model and ensures the compatibility of software that the execution result in multithreaded processor is the same as the execution result in uniprocessor. The implementation strategy of chip multithreaded consistency model in Godson-2 SMT processor is also proposed. Godson-2 SMT processor supports chip multithreaded consistency model correctly by exception scheme based on the sequential memory access queue of each thread.

  12. Tamper-indicating quantum optical seals

    Energy Technology Data Exchange (ETDEWEB)

    Humble, Travis S [ORNL; Williams, Brian P [ORNL

    2015-01-01

    Confidence in the means for identifying when tampering occurs is critical for containment and surveillance technologies. Fiber-optic seals have proven especially useful for actively surveying large areas or inventories due to the extended transmission range and flexible layout of fiber. However, it is reasonable to suspect that an intruder could tamper with a fiber-optic sensor by accurately replicating the light transmitted through the fiber. In this contribution, we demonstrate a novel approach to using fiber-optic seals for safeguarding large-scale inventories with increased confidence in the state of the seal. Our approach is based on the use of quantum mechanical phenomena to offer unprecedented surety in the authentication of the seal state. In particular, we show how quantum entangled photons can be used to monitor the integrity of a fiber-optic cable - the entangled photons serve as active sensing elements whose non-local correlations indicate normal seal operation. Moreover, we prove using the quantum no-cloning theorem that attacks against the quantum seal necessarily disturb its state and that these disturbances are immediately detected. Our quantum approach to seal authentication is based on physical principles alone and does not require the use of secret or proprietary information to ensure proper operation. We demonstrate an implementation of the quantum seal using a pair of entangled photons and we summarize our experimental results including the probability of detecting intrusions and the overall stability of the system design. We conclude by discussing the use of both free-space and fiber-based quantum seals for surveying large areas and inventories.

  13. Vacuum-sealed casting process under pressure

    Institute of Scientific and Technical Information of China (English)

    LI Chen-xi; GUO Tai-ming; WU Chun-jing; WANG Hong

    2006-01-01

    A new casting method, the vacuum-sealed mold casting under pressure, has been developed, and thin wall iron castings with high precision and smooth surface have been produced successfully with this casting method. The experimental results show that the liquid iron has a very excellent filling ability because a high negative pressure is formed in the mold cavity during filling process. The vacuum-sealed mold under pressure has very high compressive strength greater than 650 kPa, which is 3-4 times as high as that of the molds produced by high-pressure molding process or vacuum-sealed molding process.

  14. Compliant Glass Seals for SOFC Stacks

    Energy Technology Data Exchange (ETDEWEB)

    Chou, Y. S.; Choi, Jung-Pyung; Xu, Wei; Stephens, Elizabeth V.; Koeppel, Brian J.; Stevenson, Jeffry W.; Lara-Curzio, Edgar

    2014-04-01

    This report summarizes results from experimental and modeling studies performed by participants in the Solid-State Energy Conversion Alliance (SECA) Core Technology Program, which indicate that compliant glass-based seals offer a number of potential advantages over conventional seals based on de-vitrifying glasses, including reduced stresses during stack operation and thermal cycling, and the ability to heal micro-damage induced during thermal cycling. The properties and composition of glasses developed and/or investigated in these studies are reported, along with results from long-term (up to 5,800h) evaluations of seals based on a compliant glass containing ceramic particles or ceramic fibers.

  15. Infiltrating/sealing proximal caries lesions

    DEFF Research Database (Denmark)

    Martignon, S; Ekstrand, K R; Gomez, J

    2012-01-01

    This randomized split-mouth controlled clinical trial aimed at assessing the therapeutic effects of infiltration vs. sealing for controlling caries progression on proximal surfaces. Out of 90 adult students/patients assessed at university clinics and agreeing to participate, 39, each with 3...... differences in lesion progression between infiltration and placebo (P = 0.0012) and between sealing and placebo (P = 0.0269). The study showed that infiltration and sealing are significantly better than placebo treatment for controlling caries progression on proximal lesions. No significant difference...

  16. Compliant Glass Seals for SOFC Stacks

    Energy Technology Data Exchange (ETDEWEB)

    Chou, Yeong -Shyung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Choi, Jung-Pyung [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Xu, Wei [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stephens, Elizabeth V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Koeppel, Brian J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Stevenson, Jeffry W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lara-Curzio, Edgar [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2014-04-30

    This report summarizes results from experimental and modeling studies performed by participants in the Solid-State Energy Conversion Alliance (SECA) Core Technology Program, which indicate that compliant glass-based seals offer a number of potential advantages over conventional seals based on de-vitrifying glasses, including reduced stresses during stack operation and thermal cycling, and the ability to heal micro-damage induced during thermal cycling. The properties and composition of glasses developed and/or investigated in these studies are reported, along with results from long-term (up to 5,800h) evaluations of seals based on a compliant glass containing ceramic particles or ceramic fibers.

  17. Floating air riding seal for a turbine

    Energy Technology Data Exchange (ETDEWEB)

    Ebert, Todd A

    2016-08-16

    A floating air riding seal for a gas turbine engine with a rotor and a stator, an annular piston chamber with an axial moveable annular piston assembly within the annular piston chamber formed in the stator, an annular cavity formed on the annular piston assembly that faces a seal surface on the rotor, where the axial moveable annular piston includes an inlet scoop on a side opposite to the annular cavity that scoops up the swirling cooling air and directs the cooling air to the annular cavity to form an air cushion with the seal surface of the rotor.

  18. UW VLSI chip tester

    Science.gov (United States)

    McKenzie, Neil

    1989-12-01

    We present a design for a low-cost, functional VLSI chip tester. It is based on the Apple MacIntosh II personal computer. It tests chips that have up to 128 pins. All pin drivers of the tester are bidirectional; each pin is programmed independently as an input or an output. The tester can test both static and dynamic chips. Rudimentary speed testing is provided. Chips are tested by executing C programs written by the user. A software library is provided for program development. Tests run under both the Mac Operating System and A/UX. The design is implemented using Xilinx Logic Cell Arrays. Price/performance tradeoffs are discussed.

  19. Investigating the sealing capacity of a seal system in rock salt (DOPAS project)

    Energy Technology Data Exchange (ETDEWEB)

    Jantschik, Kyra; Moog, Helge C.; Czaikowski, Oliver; Wieczorek, Klaus [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Braunschweig (Germany)

    2016-11-15

    This paper describes research and development work on plugging and sealing repositories, an issue of fundamental importance for the rock salt option which represents one of the three European repository options, besides the clay rock and the crystalline rock options. The programme aims at providing experimental data needed for the theoretical analysis of the long-term sealing capacity of concrete- based sealing materials. In order to demonstrate hydro-mechanical material stability under representative load scenarios, a comprehensive laboratory testing programme is carried out. This comprises investigation of the sealing capacity of the combined seal system and impact of the so-called excavation-damaged zones (EDZ) as well as investigation of the hydro-chemical long-term stability of the seal in contact with different brines under diffusive and advective conditions. This paper presents experimental approaches and preliminary results from laboratory investigations on salt concrete and combined systems as obtained to date.

  20. Effect of bar sealing parameters on OPP/MCPP heat seal strength

    Directory of Open Access Journals (Sweden)

    2007-11-01

    Full Text Available The effect of bar sealing parameters on the heat seal strength of oriented polypropylene (OPP/metallic cast polypropylene (MCPP laminate film was investigated. Based on the results obtained from the parametric study, a bar sealing process window was developed. All points drop within the process window are combinations of platen temperature and dwell time that produce acceptable heat seal. Optimum combinations are indicated by the lower border of the window. The plateau initiation temperature, Tpi of OPP/MCPP laminate film used in the present study occurred before the final melting temperature, Tmf of the sealant material. The highest achievable heat seal strength was at the plateau region, and the corresponding failure modes were delaminating, tearing or combine failure modes (delaminating and tearing. Minimum pressure level of 1.25 bars is necessary to bring the laminate interface into intimate contact in order to effect sealing.

  1. Finite Element Analysis of Elastomeric Seals for LIDS

    Science.gov (United States)

    Oswald, Jay J.; Daniels, Christopher C.

    2007-01-01

    Objective: Create a means of evaluating seals w/o prototypes. Motivation: Cost Prototype 54" seal approx.$100k per seal pair FEA license + high end workstation approx. $30k per year. Development time: 6 months lead time for a new seal design Many designs per day (solution time <1 minute) Understanding: Difficult to experimentally measure strains, contact pressure profile, stresses, displacements

  2. Improved Gas Seal for Electrolytic Cells

    Science.gov (United States)

    Richter, R.

    1984-01-01

    Breakage by differential thermal expansion reduced. Cells for hot electrolysis of gases improved by design that reduces vulnerability of gas seals to breakage at operating temperature of about 1000 degrees C.

  3. HMSRP Hawaiian Monk Seal Survival Factors

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records of survival factors recorded by PSD personnel and cooperating scientists as part of the ongoing monk seal population assessment...

  4. HMSRP Hawaiian Monk Seal Survey Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records of Hawaiian monk seal and green turtle sightings in the Northwestern Hawaiian Islands (NWHI) since 1982 at Lisianski Island, and since...

  5. HMSRP Hawaiian Monk Seal Tag Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records for all tags applied to Hawaiian monk seals since 1981. These tags were applied by PSD personnel and cooperating scientists as part of...

  6. HMSRP Hawaiian Monk Seals on Social Media

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — As social media platforms develop, they potentially provide valuable information for wildlife researchers and managers. NOAA’s Hawaiian Monk Seal Research Program...

  7. HMSRP Hawaiian Monk Seal Necropsy Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains information on Hawaiian monk seal gross necropsy (in some cases only field notes or minimal information) and histopathology results beginning...

  8. HMSRP Hawaiian Monk Seal Photo Identification Database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This photo collection contains identification and other images and video of Hawaiian monk seals taken by PSD personnel and cooperating scientists as part of the...

  9. Temporary fire sealing of penetrations on TFTR

    Energy Technology Data Exchange (ETDEWEB)

    Hondorp, H.L.

    1981-02-01

    The radiation shielding provided for TFTR for D-D and D-T operation will be penetrated by numerous electrical and mechanical services. Eventually, these penetrations will have to be sealed to provide the required fire resistance, tritium sealability, pressure integrity and radiation attenuation. For the initial hydrogen operation, however, fire sealing of the penetrations in the walls and floor is the primary concern. This report provides a discussion of the required and desirable properties of a temporary seal which can be used to seal these penetrations for the hydrogen operation and then subsequently be removed and replaced as required for the D-D and D-T operations. Several candidate designs are discussed and evaluated and recommendations are made for specific applications.

  10. Properties of Sealing Materials in Groundwater Wells

    DEFF Research Database (Denmark)

    Köser, Claus

    on the maximum swelling pressure; i) the bulk density of the sample, and ii) whether the sample is sorted or unsorted. CT scans (Computed Tomography) have been used to evaluate certain properties of bentonite seals in a limited volume. In this context, a set of algorithms to convert CT numbers (HU unit......) into densities for clay/water systems has been developed. This method has successfully been used to evaluate e.g., macroporosity, homogenization of the bentonite seal during the hydration of water, hydraulic conductivity and the creation of channels in the bentonite seals. Based on the results obtained...... in this Ph.D. thesis, a number of recommendations has been offered; i) a change regarding the production of pellets and ii) how sealing material must be treated in the actual construction of groundwater wells....

  11. HMSRP Hawaiian Monk Seal Microsatellite Genotypes

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Currently ~2,400 Hawaiian monk seal specimens have been analyzed genetically, providing genotypes at 18 microsatellite loci. These data are organized by individual,...

  12. Epoxy resins used to seal brachytherapy seed

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Natalia Carolina Camargos; Ferraz, Wilmar Barbosa; Reis, Sergio Carneiro dos; Santos, Ana Maria Matildes dos, E-mail: nccf@cdtn.br, E-mail: ferrazw@cdtn.br, E-mail: reissc@cdtn.br, E-mail: amms@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, BH (Brazil)

    2013-07-01

    Prostate cancer treatment with brachytherapy is recommended for patients with cancer at an early stage. In this treatment, small radioactive seeds are implanted directly in the prostate gland. These seeds are composed at least of one radionuclide carrier and an X-ray marker enclosed within a metallic tube usually sealed by laser process. This process is expensive and, furthermore, it can provoke a partial volatilization of the radionuclide and change the isotropy in dose distribution around the seed. In this paper, we present a new sealing process using epoxy resin. Three kinds of resins were utilized and characterized by scanning electron microscopy (SEM), energy dispersive X ray (EDS) and by differential scanning calorimetry (DSC) after immersion in simulated body fluid (SBF) and in sodium iodine solution (NaI). The sealing process showed excellent potential to replace the sealing laser usually employed. (author)

  13. HMSRP Hawaiian Monk Seal Fisheries Interactions data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The data set contains records of all documented hookings and/or entanglements of Hawaiian monk seals with actively fished gear, both commercial and recreational. The...

  14. Contamination and potential impacts to monk seals

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — There are six main Hawaiian monk seal breeding colonies (French Frigate Shoals, Kure Atoll, Laysan Island, Lisianski Island, Pearl and Hermes Reef and Midway Atoll)...

  15. Reactor coolant pump shaft seal stability during station blackout

    Energy Technology Data Exchange (ETDEWEB)

    Rhodes, D B; Hill, R C; Wensel, R G

    1987-05-01

    Results are presented from an investigation into the behavior of Reactor Coolant Pump shaft seals during a potential station blackout (loss of all ac power) at a nuclear power plant. The investigation assumes loss of cooling to the seals and focuses on the effect of high temperature on polymer seals located in the shaft seal assemblies, and the identification of parameters having the most influence on overall hydraulic seal performance. Predicted seal failure thresholds are presented for a range of station blackout conditions and shaft seal geometries.

  16. Emergency sacrificial sealing method in filters, equipment, or systems

    Science.gov (United States)

    Brown, Erik P

    2014-09-30

    A system seals a filter or equipment component to a base and will continue to seal the filter or equipment component to the base in the event of hot air or fire. The system includes a first sealing material between the filter or equipment component and the base; and a second sealing material between the filter or equipment component and the base and proximate the first sealing material. The first sealing material and the second seal material are positioned relative to each other and relative to the filter or equipment component and the base to seal the filter or equipment component to the base and upon the event of fire the second sealing material will be activated and expand to continue to seal the filter or equipment component to the base in the event of hot air or fire.

  17. Application study of magnetic fluid seal in hydraulic turbine

    Science.gov (United States)

    Yu, Z. Y.; Zhang, W.

    2012-11-01

    The waterpower resources of our country are abundant, and the hydroelectric power is developed, but at present the main shaft sealing device of hydraulic turbine is easy to wear and tear and the leakage is great. The magnetic fluid seal has the advantages of no contact, no wear, self-healing, long life and so on. In this paper, the magnetic fluid seal would be used in the main shaft of hydraulic turbine, the sealing structure was built the model, meshed the geometry, applied loads and solved by using MULTIPHYSICS in ANSYS software, the influence of the various sealing structural parameters such as tooth width, height, slot width, sealing gap on the sealing property were analyzed, the magnetic fluid sealing device suitable for large-diameter shaft and sealing water was designed, the sealing problem of the hydraulic turbine main shaft was solved effectively which will bring huge economic benefits.

  18. Emergency sacrificial sealing method in filters, equipment, or systems

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Erik P.

    2017-02-28

    A system seals a filter or equipment component to abase and will continue to seal the filter or equipment component to the base in the event of hot air or fire. The system includes a first sealing material between the filter or equipment component and the base; and a second sealing material between the filter or equipment component and the base and proximate the first sealing material. The first sealing material and the second seal material are positioned relative to each other and relative to the filter or equipment component and the base to seal the filter or equipment component to the base and upon the event of fire the second sealing material will be activated and expand to continue to seal the filter or equipment component to the base in the event of hot air or fire.

  19. The Advantage of Sensor Sealing Laser Welding

    Institute of Scientific and Technical Information of China (English)

    YAN Yezhi; XU yu

    2007-01-01

    @@ Laser Welding Inevitably Applied in Sen sor Production Certain kinds of sensors such as pressure sensor,temperature sensor, optic-electronic sensor etc. utilize welding seal according to different application environment. With precision components and IC which is isolated by inert gas inside, these sensors should be sealed and able to resist the pressure. So the welding process must avoid distortion and harm to the components and IC.

  20. Some Aspects of Sealed Nickel Cadmium Cells

    Directory of Open Access Journals (Sweden)

    P. K. Saha

    1967-11-01

    Full Text Available Sealed Nickel Cadmium Cell system is termed till today as the most reliable power pack for electronic apparatus specially in low temperature use. This paper brings out the development and production of sealed nickel cadmium cells of pocket plate construction. The author who has gained experience in production of Ni-Cd cells in East Germany discusses also the major problems faced by the battery manufactures of to-day.

  1. Anodizing And Sealing Aluminum In Nonchromated Solutions

    Science.gov (United States)

    Emmons, John R.; Kallenborn, Kelli J.

    1995-01-01

    Improved process for anodizing and sealing aluminum involves use of 5 volume percent sulfuric acid in water as anodizing solution, and 1.5 to 2.0 volume percent nickel acetate in water as sealing solution. Replaces process in which sulfuric acid used at concentrations of 10 to 20 percent. Improved process yields thinner coats offering resistance to corrosion, fatigue life, and alloy-to-alloy consistency equal to or superior to those of anodized coats produced with chromated solutions.

  2. Troubleshooting ProSeal LMA

    Directory of Open Access Journals (Sweden)

    Bimla Sharma

    2009-01-01

    Full Text Available Supraglottic devices have changed the face of the airway management. These devices have contributed in a big way in airway management especially, in the difficult airway scenario significantly decreasing the pharyngolaryngeal morbidity. There is a plethora of these devices, which has been well matched by their wider acceptance in clinical practice. ProSeal laryngeal mask airway (PLMA is one such frequently used device employed for spontaneous as well as controlled ventilation. However, the use of PLMAat tunes maybe associated with certain problems. Some of the problems related with its use are unique while others are akin to the classic laryngeal mask airway (eLMA. However, expertise is needed for its safe and judicious use, correct placement, recognition and management of its various malpositions and complications. The present article describes the tests employed for proper confirmation of placementto assess the ventilatooy and the drain tube functions of the mask, diagnosis of various malpositions and the management of these aspects. All these areas have been highlighted under the heading of troubleshooting PLMA. Many problems can be solved by proper patient and procedure selection, maintaining adequate depth of anaesthesia, diagnosis and management of malpositions. Proper fixation of the device and monitoring cuff pressure intraopera-tively may bring down the incidence of airway morbidity.

  3. Aerodynamical sealing by air curtains

    Science.gov (United States)

    Frank, Daria; Linden, Paul

    2015-11-01

    Air curtains are artificial high-velocity plane turbulent jets which are installed in a doorway in order to reduce the heat and the mass exchange between two environments. The performance of an air curtain is assessed in terms of the sealing effectiveness E, the fraction of the exchange flow prevented by the air curtain compared to the open-door situation. The main controlling parameter for air curtain dynamics is the deflection modulus Dm representing the ratio of the momentum flux of the air curtain and the transverse forces acting on it due to the stack effect. In this talk, we examine the influence of two factors on the performance of an air curtain: the presence of an additional ventilation pathway in the room, such as a small top opening, and the effects of an opposing buoyancy force which for example arises if a downwards blowing air curtain is heated. Small-scale experiments were conducted to investigate the E (Dm) -curve of an air curtain in both situations. We present both experimental results and theoretical explanations for our observations. We also briefly illustrate how simplified models developed for air curtains can be used for more complex phenomena such as the effects of wind blowing around a model building on the ventilation rates through the openings.

  4. Adhesive sealing of the pulp chamber.

    Science.gov (United States)

    Belli, S; Zhang, Y; Pereira, P N; Pashley, D H

    2001-08-01

    The purpose of this in vitro study was to evaluate quantitatively the ability of four different filling materials to seal the orifices of root canals as a secondary seal after root canal therapy. Forty extracted human molar teeth were used. The top of pulp chambers and distal halves of the roots were removed using an Isomet saw. The canal orifices were temporarily sealed with a gutta-percha master cone without sealer. The pulp chambers were then treated with a self-etching primer adhesive system (Clearfil SE Bond), a wet bonding system (One-Step), a 4-methacryloyloxyethyl trimellitate anhydride adhesive system (C&B Metabond), or a reinforced zinc oxide-eugenol (IRM). The specimens were randomly divided into four groups of 10 each. A fluid filtration method was used for quantitative evaluation of leakage. Measurements of fluid movement were made at 2-min intervals for 8 min. The quality of the seal of each specimen was measured by fluid filtration immediately and after 1 day, 1 wk, and 1 month. Even after 1 month the resins showed an excellent seal. Zinc oxide-eugenol had significantly more leakage when compared with the resin systems (p < 0.05). Adhesive resins should be considered as a secondary seal to prevent intraorifice microleakage.

  5. Predicting edge seal performance from accelerated testing

    Science.gov (United States)

    Hardikar, Kedar; Vitkavage, Dan; Saproo, Ajay; Krajewski, Todd

    2014-10-01

    Degradation in performance of a PV module attributable to moisture ingress has received significant attention in PV reliability research. Assessment of field performance of PV modules against moisture ingress through product-level testing in temperature-humidity control chambers poses challenges. Development of a meaningful acceleration factor model is challenging due to different rates of degradation of components embedded in a PV module, when exposed to moisture. Test results are typically a convolution of moisture barrier performance of the edge seal and degradation of laminated components when exposed to moisture. It is desirable to have an alternate method by which moisture barrier performance of the edge seal in its end product form can be assessed in any given field conditions, independent of particular cell design. In this work, a relatively inexpensive test technique was developed to test the edge seal in its end product form in a manner that is decoupled from other components of the PV module. A theoretical framework was developed to assess moisture barrier performance of edge seal with desiccants subjected to different conditions. This framework enables the analysis of test results from accelerated tests and prediction of the field performance of the edge seal. Results from this study lead to the conclusion that the edge seal on certain Miasole glass-glass modules studied is effective for the most aggressive weather conditions examined, beyond the intended service.

  6. Sealing device and method for sealing fractures or leaks in wall or formation surrounding tube-shaped channel

    DEFF Research Database (Denmark)

    2014-01-01

    (11) arranged between the second annular flow barrier (8) and a third annular flow barrier (12) and including a sealing fluid activation device (13) adapted to at least initiate or accelerate curing of the sealing fluid (17). In operation, the elongated body may be displaced along the tube......-shaped channel until the sealing fluid activation section is placed at a position where sealing fluid has been ejected by the sealing fluid placement section, and the sealing fluid activation device may be activated. Thereby, sealing fluid may be cured at selected locations along the tube-shaped channel after...

  7. ALICE chip processor

    CERN Multimedia

    Maximilien Brice

    2003-01-01

    This tiny chip provides data processing for the time projection chamber on ALICE. Known as the ALICE TPC Read Out (ALTRO), this device was designed to minimize the size and power consumption of the TPC front end electronics. This single chip contains 16 low-power analogue-to-digital converters with six million transistors of digital processing and 8 kbits of data storage.

  8. DEVELOPMENT OF A CERAMIC TAMPER INDICATING SEAL: SRNL CONTRIBUTIONS

    Energy Technology Data Exchange (ETDEWEB)

    Krementz, D.; Brinkman, K.; Martinez-Rodriguez, M.; Mendez-Torres, A.; Weeks, G.

    2013-06-03

    Savannah River National Laboratory (SRNL) and Sandia National Laboratories (SNL) are collaborating on development of a Ceramic Seal, also sometimes designated the Intrinsically Tamper Indicating Ceramic Seal (ITICS), which is a tamper indicating seal for international safeguards applications. The Ceramic Seal is designed to be a replacement for metal loop seals that are currently used by the IAEA and other safeguards organizations. The Ceramic Seal has numerous features that enhance the security of the seal, including a frangible ceramic body, protective and tamper indicating coatings, an intrinsic unique identifier using Laser Surface Authentication, electronics incorporated into the seal that provide cryptographic seal authentication, and user-friendly seal wire capture. A second generation prototype of the seal is currently under development whose seal body is of Low Temperature Co-fired Ceramic (LTCC) construction. SRNL has developed the mechanical design of the seal in an iterative process incorporating comments from the SNL vulnerability review team. SRNL is developing fluorescent tamper indicating coatings, with recent development focusing on optimizing the durability of the coatings and working with a vendor to develop a method to apply coatings on a 3-D surface. SRNL performed a study on the effects of radiation on the electronics of the seal and possible radiation shielding techniques to minimize the effects. SRNL is also investigating implementation of Laser Surface Authentication (LSA) as a means of unique identification of each seal and the effects of the surface coatings on the LSA signature.

  9. Advanced flip chip packaging

    CERN Document Server

    Lai, Yi-Shao; Wong, CP

    2013-01-01

    Advanced Flip Chip Packaging presents past, present and future advances and trends in areas such as substrate technology, material development, and assembly processes. Flip chip packaging is now in widespread use in computing, communications, consumer and automotive electronics, and the demand for flip chip technology is continuing to grow in order to meet the need for products that offer better performance, are smaller, and are environmentally sustainable. This book also: Offers broad-ranging chapters with a focus on IC-package-system integration Provides viewpoints from leading industry executives and experts Details state-of-the-art achievements in process technologies and scientific research Presents a clear development history and touches on trends in the industry while also discussing up-to-date technology information Advanced Flip Chip Packaging is an ideal book for engineers, researchers, and graduate students interested in the field of flip chip packaging.

  10. CHIP, CHIP, ARRAY! THREE CHIPS FOR POST-GENOMIC RESEARCH

    Science.gov (United States)

    Cambridge Healthtech Institute recently held the 4th installment of their popular "Lab-on-a-Chip" series in Zurich, Switzerland. As usual, it was enthusiastically received and over 225 people attended the 2-1/2 day meeting to see and hear about some of the latest developments an...

  11. Heartworm (Acanthocheilonema spirocauda) and seal louse (Echinophthirius horridus) infections in harbour seals (Phoca vitulina) from the North and Baltic Seas

    Science.gov (United States)

    Lehnert, Kristina; Schwanke, Eva; Hahn, Kerstin; Wohlsein, Peter; Siebert, Ursula

    2016-07-01

    The seal louse (Echinophthirius [E.] horridus) and the heartworm (Acanthocheilonema [A.] spirocauda) are parasites of harbour seal (Phoca vitulina). Little is known about the role of the seal louse as a potential vector and its role for the development and transmission of heartworm larvae to their final host, the harbour seal. The life-cycle of the heartworm is still not fully understood. For the presented study, findings of 1191 stranded harbour seals collected along the North- and Baltic Sea coast between 1996 and 2013 were examined. 4.4% (n = 53) of these harbour seals were infected with adult heartworms and 3.4% (n = 40) harbour seals carried seal lice. The highest prevalence and level of infection with adult heartworms (A. spirocauda) (9.3%) and seal lice (E. horridus) (8.9%) were found on yearling harbour seals (7-18 months) compared to neonate and adult seals. Investigating seal lice (n = 35) for larval heartworm stages one larvae was encountered in an ethanol-fixated seal louse. During a health monitoring survey of live harbour seals, 109 animals were captured and examined during spring and autumn between 2008 and 2014. Blood samples were taken and microfilariae were discovered in blood smears in 41% (n = 45) of the examined harbour seals. Yearling seals (n = 21) showed higher prevalence (86%) and level of infection with microfilariae than adults. Microfilariae were identified as A. spirocauda by sequencing the species-specific COI gene in 24 blood samples. The high prevalence of microfilariae of A. spirocauda in blood samples (41%) is in contrast to the low prevalence of mature infections/adult specimens in stranded seals (4.4%) investigated. Although rare parasites of seals, the recent increase in prevalence of heartworm and seal lice in stranded seals and the relatively high occurrence of microfilaria in the free-ranging population underscore the importance of further studies investigating the immunology of infections and their transmission pathways, as

  12. Low-cost thermoforming of micro fluidic analysis chips

    Science.gov (United States)

    Truckenmüller, R.; Rummler, Z.; Schaller, Th; Schomburg, W. K.

    2002-07-01

    We present a new method for the low-cost manufacture of micro fluidic devices from polymers for single use. Within a one-step or two-step process inside a hot embossing press, micro channels are thermoformed into a thin plastic film and welded on to a thicker plastic film or sheet. Sterile, hermetically sealed micro fluidic structures were fabricated from polystyrene for easy opening immediately before use. It even appears to be possible to produce micro fluidic analysis chips from polymers on a coil from which single devices are cut off for use.

  13. Effects of rejuvenator seal and fog seal on performance of open-graded friction course pavement

    Directory of Open Access Journals (Sweden)

    Nadeem A. Qureshi

    2013-05-01

    Full Text Available An open-graded friction course (OGFC is a special-purpose surface layer of hot-mix asphalt (HMA pavement that is increasingly being used around the world. Owing to its numerous benefits, OGFC is being regularly used as a final riding surface on interstate and high-traffic expressways by different highway agencies in the United States. However, some OGFC sections have experienced premature failure due to ravelling only after 6-8 years of service life. To maintain an effective, longer service life and enhanced performance of OGFC, preventive maintenance has been considered essential. There are several approaches to maintaining OGFC, one of which is the application of a fog seal and rejuvenator seal. A fog seal can reduce ravelling and extend the service life of OGFC while a rejuvenator seal can revitalise the existing aged asphalt binder in the top OGFC layer. This research focuses on optimising the fog and rejuvenator seal application rates by evaluating their effectiveness in terms of surface friction and durability. Three types of seal material were evaluated: Pavegaard (PG and Pavepreserve (PP asphalt rejuvenators and a cationic slow-setting asphalt emulsion (CSS-1H as a fog seal. Improvement in abrasion resistance of OGFC pavement was observed on application of fog and rejuvenator seals but surface friction was reduced to some extent. Hamburg test clearly shows a trend that the medium application rate of 0.10 gallon/square yard is better in enhancing resistance to rutting/moisture susceptibility of OGFC.

  14. Development of sprayed ceramic seal systems for turbine gas path sealing

    Science.gov (United States)

    Bill, R. C.; Shiembob, L. T.; Stewart, O. L.

    1978-01-01

    A ceramic seal system is reported that employs plasma-sprayed graded metal/ceramic yttria stabilized zirconium oxide (YSZ). The performance characteristics of several YSZ configurations were determined through rig testing for thermal shock resistance, abradability, and erosion resistance. Results indicate that this type of sealing system offers the potential to meet operating requirements of future gas turbine engines.

  15. Diffusion driven optofluidic dye lasers encapsulated into polymer chips

    DEFF Research Database (Denmark)

    Wienhold, Tobias; Breithaupt, Felix; Vannahme, Christoph

    2012-01-01

    that these first order distributed feedback lasers can be operated for more than 90 min at a pulse repetition rate of 2 Hz without fluidic pumping. Ultra-high output pulse energies of more than 10 μJ and laser thresholds of 2 μJ are achieved for resonator lengths of 3 mm. By introducing comparatively large on...... of micro- and nanoscale structures into 100 μm foils simultaneously defines photonic resonators, liquid-core waveguides, and fluidic reservoirs. Subsequently, the fluidic structures are sealed with another 220 μm foil by thermal bonding. Tunability of laser output wavelengths over a spectral range of 24 nm...... on a single chip is accomplished by varying the laser grating period in steps of 2 nm. Low-cost manufacturing suitable for mass production, wide laser tunability, ultra-high output pulse energies, and long operation times without external fluidic pumping make these on-chip lasers suitable for a wide range...

  16. Development of a Whole Container Seal

    Energy Technology Data Exchange (ETDEWEB)

    Kuhn, Michael J [ORNL; Pickett, Chris A [ORNL; Stinson, Brad J [ORNL; Rowe, Nathan C [ORNL

    2014-01-01

    This paper outlines a technique for utilizing electrically conductive textiles as a whole container seal. This method has the potential to provide more robustness for ensuring that the container has not been breached versus conventional sealing methods that only provide tamper indication at the area used for normal access. The conductive textile is used as a distributed sensor for detecting and localizing container tamper or breach. For sealing purposes, the conductive fabric represents a bounded, near-infinite grid of resistors. The well-known infinite resistance grid problem was used to model and confirm the expected accuracy and validity of this approach. An experimental setup was built that uses a multiplexed Wheatstone bridge measurement to determine the resistances of a coarse electrode grid across the conductive fabric. Non-uniform resistance values of the grid infer the presence of damage or tears in the fabric. Results suggest accuracy proportional to the electrode spacing in determining the presence and location of disturbances in conductive fabric samples. Current work is focused on constructing experimental prototypes for field and environmental testing to gauge the performance of these whole container seals in real world conditions. We are also developing software and hardware to interface with the whole container seals. The latest prototypes are expected to provide more accuracy in detecting and localizing events, although detection of a penetration should be adequate for most sealing applications. We are also developing smart sensing nodes that integrate digital hardware and additional sensors (e.g., motion, humidity) into the electrode nodes within the whole container seal.

  17. Solid oxide fuel cell having a glass composite seal

    Science.gov (United States)

    De Rose, Anthony J.; Mukerjee, Subhasish; Haltiner, Jr., Karl Jacob

    2013-04-16

    A solid oxide fuel cell stack having a plurality of cassettes and a glass composite seal disposed between the sealing surfaces of adjacent cassettes, thereby joining the cassettes and providing a hermetic seal therebetween. The glass composite seal includes an alkaline earth aluminosilicate (AEAS) glass disposed about a viscous glass such that the AEAS glass retains the viscous glass in a predetermined position between the first and second sealing surfaces. The AEAS glass provides geometric stability to the glass composite seal to maintain the proper distance between the adjacent cassettes while the viscous glass provides for a compliant and self-healing seal. The glass composite seal may include fibers, powders, and/or beads of zirconium oxide, aluminum oxide, yttria-stabilized zirconia (YSZ), or mixtures thereof, to enhance the desirable properties of the glass composite seal.

  18. Mechanical seal having a single-piece, perforated mating ring

    Science.gov (United States)

    Khonsari, Michael M.; Somanchi, Anoop K.

    2007-08-07

    A mechanical seal (e.g., single mechanical seals, double mechanical seals, tandem mechanical seals, bellows, pusher mechanical seals, and all types of rotating and reciprocating machines) with reduced contact surface temperature, reduced contact surface wear, or increased life span. The mechanical seal comprises a rotating ring and a single-piece, perforated mating ring, which improves heat transfer by controllably channeling coolant flow through the single-piece mating ring such that the coolant is in substantially uniform thermal contact with a substantial portion of the interior surface area of the seal face, while maintaining the structural integrity of the mechanical seal and minimizing the potential for coolant flow interruptions to the seal face caused by debris or contaminants (e.g., small solids and trash) in the coolant.

  19. Advanced helium purge seals for Liquid Oxygen (LOX) turbopumps

    Science.gov (United States)

    Shapiro, Wilbur; Lee, Chester C.

    1989-01-01

    Program objectives were to determine three advanced configurations of helium buffer seals capable of providing improved performance in a space shuttle main engine (SSME), high-pressure liquid oxygen (LOX) turbopump environment, and to provide NASA with the analytical tools to determine performance of a variety of seal configurations. The three seal designs included solid-ring fluid-film seals often referred to as floating ring seals, back-to-back fluid-film face seals, and a circumferential sectored seal that incorporated inherent clearance adjustment capabilities. Of the three seals designed, the sectored seal is favored because the self-adjusting clearance features accommodate the variations in clearance that will occur because of thermal and centrifugal distortions without compromising performance. Moreover, leakage can be contained well below the maximum target values; minimizing leakage is important on the SSME since helium is provided by an external tank. A reduction in tank size translates to an increase in payload that can be carried on board the shuttle. The computer codes supplied under this program included a code for analyzing a variety of gas-lubricated, floating ring, and sector seals; a code for analyzing gas-lubricated face seals; a code for optimizing and analyzing gas-lubricated spiral-groove face seals; and a code for determining fluid-film face seal response to runner excitations in as many as five degrees of freedom. These codes proved invaluable for optimizing designs and estimating final performance of the seals described.

  20. Molecular characterization of mycobacteria isolated from seals.

    Science.gov (United States)

    Zumárraga, M J; Bernardelli, A; Bastida, R; Quse, V; Loureiro, J; Cataldi, A; Bigi, F; Alito, A; Castro Ramos, M; Samper, S; Otal, I; Martin, C; Romano, M I

    1999-09-01

    Tuberculosis (TB) was diagnosed in 10 seals from three species (Arctocephalus australis, Arctocephalus tropicalis and Otaria flavescens) found in South America. The mycobacteria isolated from these cases belonged to the Mycobacterium tuberculosis complex, as determined by RFLP using an IS6110 probe, spoligotyping, analysis of the 16S rRNA gene sequence and by PCR-restriction analysis of hsp65. Polymorphisms in gyrA, katG, oxyR and pncA were investigated in some of the isolates, as well as the presence of the MPB70 antigen. The insertion sequence IS6110 was present in three to seven copies in the genome of the mycobacteria isolated from seals. Using the IS6110 probe, six patterns (designated A, B, C, D, E and F) were identified from 10 different isolates. Patterns A and B were found for the mycobacteria isolated from two and four seals, respectively, indicating an epidemiological relationship between isolates grouped according to their IS6110 RFLP. The mycobacteria isolated from seals shared the majority of their IS6110 DNA-containing restriction fragments, and nine isolates had an identical spoligotype; only one isolate showed a minor difference in its spoligotype. In addition, none of these spoligotypes were found in other M. tuberculosis complex strains. These results suggest that the isolates from seals constitute a unique group of closely related strains. The mycobacteria isolated from seals showed polymorphisms at gyrA codon 95 and katG codon 463, as do group 1 M. tuberculosis, and M. bovis. Group 1 mycobacteria are associated with cluster cases. The spoligotypes found in the mycobacteria isolated from seals lack spacers 39-43, as does M. bovis, but the MPB70 antigen, which is highly expressed in M. bovis and minimally expressed in M. tuberculosis, was not detected in these mycobacteria. The mycobacteria isolated from seals also showed oxyR and pncA polymorphisms specific to M. tuberculosis. In conclusion, the mycobacteria that cause TB in seals in the South

  1. Capillary-driven microfluidic chips with evaporation-induced flow control and dielectrophoretic microbead trapping

    Science.gov (United States)

    Temiz, Yuksel; Skorucak, Jelena; Delamarche, Emmanuel

    2014-07-01

    This work reports our efforts on developing simple-to-use microfluidic devices for point-of-care diagnostic applications with recent extensions that include the trapping of microbeads using dielectrophoresis (DEP) and the modulation of the liquid flow using integrated microheaters. DEP serves the purpose of trapping microbeads coated with receptors and analytes for detection of a fluorescent signal. The microheater is actuated once the chip is filled by capillarity, creating an evaporation-induced flow tuned according to assay conditions. The chips are composed of a glass substrate patterned with 50-nm-thick Pd electrodes and microfluidic structures made using a 20-μm-thick dry-film resist (DFR). Chips are covered/sealed by low temperature (50°C) lamination of a 50-μm-thick DFR layer having excellent optical and mechanical properties. To separate cleaned and sealed chips from the wafer, we used an effective chip singulation technique which we informally call the "chip-olate" process. In the experimental section, we first studied dielectrophoretic trapping of 10-μm beads for flow rates ranging from 80 pL s-1 to 2.5 nL s-1 that are generated by an external syringe pump. Then, we characterized the embedded microheater in DFR-covered chips. Flow rates as high as 8 nL s-1 were generated by evaporation-induced flow when the heater was biased by 10 V, corresponding to 270-mW power. Finally, DEP-based trapping and fluorescent detection of functionalized beads were demonstrated as the flow was generated by evaporation-induced flow after the microfluidic structures were filled by capillarity.

  2. Seal assembly with anti-rotation pin for high pressure supercritical fluids

    Science.gov (United States)

    Wright, Steven A.; Fuller, Robert L.

    2014-08-05

    A seal assembly for sealing a machine with a first chamber and a second chamber is provided. A rotating shaft extends through the first and second chambers, and rotates therein. The seal assembly has a seal housing, a seal ring and a seal pin. The seal housing is positionable in the machine housing. The seal housing has a seal pocket extending into a fluid side thereof, and a housing receptacle extending into an inner diameter thereof at the seal pocket. The seal ring is positionable in the seal pocket of the seal housing for forming a seal therewith. The seal ring has a ring receptacle extending into an outer diameter thereof. The ring receptacle is positionable adjacent to the housing receptacle for defining a pin hole therebetween. The seal pin is loosely positionable in the pin hole whereby movement about the seal ring is accommodated while preventing rotation thereof.

  3. Cylindrical electrochemical cells with a diaphragm seal

    Energy Technology Data Exchange (ETDEWEB)

    Georgopoulos, P.

    1993-07-13

    A cylindrical electrochemical cell is described comprising an anode, a cathode and electrolyte contained in a cylindrical container, the container having an open end and a closed end; wherein the open end of the container is sealed with a seal assembly comprising: (a) a disc-shaped seal member, made from an electrically insulative material, having an outer edge wall connected via a base to a centrally located cylindrical hub that defines an orifice; which base has a ventable diaphragm portion and a nonventable diaphragm portion that is thicker than the ventable diaphragm portion; and wherein the ventable diaphragm portion joins the hub at an interface and becomes gradually thicker in the direction away from the interface toward the outer edge wall so that the ventable diaphragm portion is thinnest at the interface; and (b) a current collector extending through the orifice defined by the hub into the cell's interior to contact one of the cell's electrodes.

  4. Kinetic characterization of on-chip DNA ligation on dendron-coated surfaces with nanoscaled lateral spacings

    Science.gov (United States)

    Kim, Eung-Sam; Lee, Namgyu; Park, Joon Won; Choi, Kwan Yong

    2013-10-01

    We analyzed the enzymatic profiles of on-chip DNA ligation as we controlled the lateral spacing of surface-immobilized DNA substrates using dendron molecules with different sizes at the nanoscale. Enzymatic on-chip DNA ligation was performed on the dendron-coated surface within 20 min with no need for post-ligation gel electrophoresis. The enzymatic DNA repair was assessed by the fluorescence intensity at the repaired DNA duplex after thermally dissociating the unligated Cy3-labeled DNA from the DNA duplex, in which the Cy3-labeled DNA was hybridized prior to the on-chip DNA ligation. The rate of the nick-sealing reaction on the 27-acid dendron surface was 3-fold higher than that on the 9-acid dendron surface, suggesting that the wider lateral spacing determined by the larger dendron molecule could facilitate the access of DNA ligase to the nick site. The performance of on-chip DNA ligation was dropped to 10% and 3% when the nick was replaced by one- and two-nucleotide-long gaps, respectively. The 5‧ terminal phosphorylation of DNA strands by polynucleotide kinase and the on-chip DNA cleavage by endonucleases were also quantitatively monitored throughout the on-chip DNA ligation on the dendron-coated surface. A better understanding of the enzymatic kinetics of on-chip DNA ligation will contribute to a more reliable performance of various on-chip DNA ligation-based assays.

  5. Intracoronal sealing ability of two dental cements.

    Science.gov (United States)

    Wells, John D; Pashley, David H; Loushine, Robert J; Weller, R Norman; Kimbrough, W Frank; Pereira, Patricia N

    2002-06-01

    The purpose of this study was to compare the efficacy of sealing the coronal 2-mm of the root canals versus covering the entire pulpal floor with one of two dental-resin cements (Principle or C&B Metabond). Sixty-two molars with the occlusal half of the crowns and the apical half of the roots removed were used. Each canal was enlarged by using a #3 Gates Glidden bur and obturated with unsealed gutta-percha cones. The teeth were randomly assigned to four groups, each containing 15 teeth, plus a negative and a positive control. In group 1, 2 mm of Principle were placed over the entire pulpal floor. In group 2, Principle was placed 2 mm into each canal orifice. Groups 3 and 4 were the same as groups 1 and 2, except C&B Metabond cement was used. After the cement set, the gutta-percha was removed and the integrity of the seal was tested by fluid filtration at a pressure of 20 cm H2O at 1 h and at 1, 2, and 4 weeks. The data were analyzed by a three-way ANOVA and the Student-Newman-Keuls tests at alpha = 0.05. The controls behaved as expected. Results showed that there were no statistically significant differences among the materials used or the location (p > 0.05), but there was a significant difference with respect to time. Principle leaked significantly more than C&B Metabond at 1 h (p < 0.05), but the seal became tighter over time. C&B Metabond leaked less early (p < 0.05) but increased in leakage at 4 weeks. Both materials sealed well over the 4-week study. Principle was easier to use, and sealing the entire pulpal floor was easier than sealing only the canal orifice.

  6. Dynamic analysis of C/C composite finger seal

    Institute of Scientific and Technical Information of China (English)

    Chen Guoding; Wang Li’na; Yu Qiangpeng; Su Hua

    2014-01-01

    A seal device as an important component of aeroengines has decisive influence on per-formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer-ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization;in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor-mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal’s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.

  7. Dynamic analysis of C/C composite finger seal

    Directory of Open Access Journals (Sweden)

    Chen Guoding

    2014-06-01

    Full Text Available A seal device as an important component of aeroengines has decisive influence on performance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineering fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic performance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal’s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.

  8. Study on a new type of sealing - regeneration-labyrinth sealing for displacer in cryocoolers: Part I - Theoretical study

    Science.gov (United States)

    Liu, L. Q.; Zhang, L.

    2000-02-01

    A new concept of sealing structure - regeneration-labyrinth sealing has been put forward to substitute for sealing rings that influence seriously the performance of cryocoolers. A program, which can simulate the thermophysical process occurring in the sealing structure, is developed consequently. Using numerical simulation, the reasonable structure of the regeneration-labyrinth sealing has been determined. The influences of some parameters, such as the heat transfer coefficient of forced convection, the cylinder-displacer gap, the diameter and length of cylinder on the losses of cooling capacity have been studied numerically. As a result, the designing principle of the new type of sealing is obtained.

  9. Space Shuttle Orbiter AFT heat shield seal

    Science.gov (United States)

    Walkover, L. J.

    1979-01-01

    The evolution of the orbiter aft heat shield seal (AHSS) design, which involved advancing mechanical seal technology in severe thermal environment is discussed. The baseline design, various improvements for engine access, and technical problem solution are presented. It is a structure and mechanism at the three main propulsion system (MPS) engine interfaces to the aft compartment structure. Access to each MPS engine requires disassembly and removal of the AHSS. Each AHSS accommodates the engine movement, is exposed to an extremely high temperature environment, and is part of the venting control of the aft compartment.

  10. Fluid seals technology at BHR Group Ltd.

    Science.gov (United States)

    Leefe, Simon

    1991-01-01

    A mathematical model was developed for ESA, which couples the rigid body dynamics in four degrees of freedom of a flexibly mounted stator (with Coulomb damping) of a turbopump face seal with the fluid film behavior. The interfacial film is assumed gaseous, and the model incorporates laminar/turbulent flow, inertia and sonic choking. Seal faces may be wavy and coned, while the rotating ring can be eccentrically mounted, misaligned with the shaft and oscillate axially at arbitrary frequency. The model is currently being coded into software. An experimental program using a high speed cryogenic/hot gas test rig is being conducted to verify the output of the computer program.

  11. China's first WLAN chips

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ The wireless local area network (WLAN) chips independently developed by CAS researchers were in the limelight of the recent Electronic Manufacture Exposition held in Suzhou, east China's Jiangsu Province.

  12. CHIP Enrollment Reports

    Data.gov (United States)

    U.S. Department of Health & Human Services — CHIP quarterly and annual statistical enrollment reports. The quarterly reports contain point-in-time and ever enrolled data and the annual reports contain ever...

  13. Medicaid CHIP ESPC Database

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Environmental Scanning and Program Characteristic (ESPC) Database is in a Microsoft (MS) Access format and contains Medicaid and CHIP data, for the 50 states and...

  14. Fissure seal or fluoride varnish?

    Science.gov (United States)

    Deery, Christopher

    2016-09-01

    Data sourcesCochrane Oral Health Group Trials Register, the Cochrane Central Register of Controlled Trials (CENTRAL), Medline, Embase, the US National Institutes of Health Trials Register and the World Health Organization (WHO) Clinical Trials Registry PlatformStudy selectionRandomised controlled trials (RCTs) with at least 12 months follow-up, in which fissure sealants, or fissure sealants together with fluoride varnishes, were compared with fluoride varnishes alone for preventing caries in occlusal surfaces of permanent teeth of children and adolescents.Data extraction and synthesisTwo reviewers independently screened search results, extracted data and assessed risk of bias of included studies. Studies were grouped and analysed on the basis of sealant material type (resin-based sealant and glass ionomer-based sealant, glass ionomer and resin-modified glass ionomer) and different follow-up periods. Odds ratio were calculated for caries or no caries on occlusal surfaces of permanent molar teeth. Mean differences were calculated for continuous outcomes and data. Evidence quality was assessed using GRADE (Grades of Recommendation, Assessment, Development and Evaluation) methods.ResultsEight RCTs involving a total of 1747 children aged five to ten years of age were included. Three trials compared resin-based fissure sealant versus fluoride varnish. Results from two studies (358 children) after two years were combined. Sealants prevented more caries, pooled odds ratio (OR) = 0.69 (95%CI; 0.50 to 0.94). One trial with follow-up at four and nine years found that the caries-preventive benefit for sealants was maintained, with 26% of sealed teeth and 55.8% of varnished teeth having developed caries at nine years. Evidence for glass-ionomer sealants was of low quality. One split-mouth trial analysing 92 children at two-year follow-up found a significant difference in favour of resin-based fissure sealant together with fluoride varnish compared with fluoride varnish only (OR

  15. HMSRP Hawaiian Monk Seal Cell Phone Tag Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This project investigates foraging behavior of Hawaiian monk seals by conducting telemetry studies. During these studies, live seals are instrumented with dive...

  16. HMSRP Hawaiian Monk Seal Master Identification Records (annual)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set contains records of all individually identified Hawaiian monk seals since 1981. These seals were identified by PSD personnel and cooperating...

  17. Bentonite as a waste isolation pilot plant shaft sealing material

    Energy Technology Data Exchange (ETDEWEB)

    Daemen, J.; Ran, Chongwei [Univ. of Nevada, Reno, NV (United States)

    1996-12-01

    Current designs of the shaft sealing system for the Waste Isolation Pilot Plant (WIPP) propose using bentonite as a primary sealing component. The shaft sealing designs anticipate that compacted bentonite sealing components can perform through the 10,000-year regulatory period and beyond. To evaluate the acceptability of bentonite as a sealing material for the WIPP, this report identifies references that deal with the properties and characteristics of bentonite that may affect its behavior in the WIPP environment. This report reviews published studies that discuss using bentonite as sealing material for nuclear waste disposal, environmental restoration, toxic and chemical waste disposal, landfill liners, and applications in the petroleum industry. This report identifies the physical and chemical properties, stability and seal construction technologies of bentonite seals in shafts, especially in a saline brine environment. This report focuses on permeability, swelling pressure, strength, stiffness, longevity, and densification properties of bentonites.

  18. Reactor coolant pump shaft seal behavior during station blackout

    Energy Technology Data Exchange (ETDEWEB)

    Kittmer, C.A.; Wensel, R.G.; Rhodes, D.B.; Metcalfe, R.; Cotnam, B.M.; Gentili, H.; Mings, W.J.

    1985-04-01

    A testing program designed to provide fundamental information pertaining to the behavior of reactor coolant pump (RCP) shaft seals during a postulated nuclear power plant station blackout has been completed. One seal assembly, utilizing both hydrodynamic and hydrostatic types of seals, was modeled and tested. Extrusion tests were conducted to determine if seal materials could withstand predicted temperatures and pressures. A taper-face seal model was tested for seal stability under conditions when leaking water flashes to steam across the seal face. Test information was then used as the basis for a station blackout analysis. Test results indicate a potential problem with an elastomer material used for O-rings by a pump vendor; that vendor is considering a change in material specification. Test results also indicate a need for further research on the generic issue of RCP seal integrity and its possible consideration for designation as an unresolved safety issue.

  19. Evaluation of Subterranean Subsidence at Seal Beach National Wildlife Refuge

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The purpose of this study was to determine the amount of subsurface subsidence at Naval Weapons Station Seal Beach (NWSSB) areas which include Seal Beach National...

  20. Automatic Inspection Of Heat Seals Between Plastic Sheets

    Science.gov (United States)

    Rai, Kula R.; Lew, Thomas M.; Sinclair, Robert B.

    1995-01-01

    Automatic inspection apparatus detects flaws in heat seals between films of polyethylene or other thermoplastic material. Heat-sealed strip in multilayer plastic sheet continuously moved lengthwise over illuminators. Variations in light transmitted through sheet interpreted to find flaws in heat seal. Site of flaw marked to facilitate subsequent manual inspection. Heat sealing used to join plastic films in manufacturing of variety of products, including inflatable toys and balloons carrying scientific instruments to high altitudes.

  1. Non-contacting shaft seals for gas and steam turbines

    OpenAIRE

    2012-01-01

    Improvements upon current gas turbine sealing technology performance are essential for decreasing specific fuel consumption to meet stringent future efficiency targets. The clearances between rotating and static components of a gas turbine, which need to be sealed, vary over a flight cycle. Hence, a seal which can passively maintain an optimum clearance, whilst preventing contact between itself and the rotor, is extremely desirable. Various configurations of a Rolls Royce (RR) seal concep...

  2. Sealing materials for solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, P.H.

    1999-02-01

    A major obstacle in the achievement of high electrical efficiency for planar solid oxide fuel cell stacks (SOFC) is the need for long term stable seals at the operational temperature between 850 and 1000 deg. C. In the present work the formation and properties of sealing materials for SOFC stacks that fulfil the necessary requirements were investigated. The work comprises analysis of sealing material properties independently, in simple systems as well as tests in real SOFC stacks. The analysed sealing materials were based on pure glasses or glass-ceramic composites having B{sub 2}O{sub 3}, P{sub 2}O{sub 5} or siO{sub 2} as glass formers, and the following four glass systems were investigated: MgO/caO/Cr{sub 2}O{sub 3}-Al{sub 2}O{sub 3}B{sub 2}O{sub 3}-P{sub 2}O{sub 5}, MgO-Al{sub 2}O{sub 3}-P{sub 2}O{sub 5}, MgO-Al{sub 2}O{sub 3}-P{sub 2}O{sub 5}-SiO{sub 2} and BaO/Na{sub 2}O-Al{sub 2}O{sub 3}-SiO{sub 2}. (au) 32 tabs., 106 ills., 107 refs.

  3. On the lubrication of mechanical face seals

    NARCIS (Netherlands)

    Lubbinge, Hans

    1999-01-01

    Hence, in this thesis, a model is presented which is able to calculate a complete Stribeck curve for a mechanical face seal and, as a consequence, the transition from full film to mixed lubrication as a function of the operational conditions. This model is based on a combination of a contact model a

  4. Measure Guideline: Guide to Attic Air Sealing

    Energy Technology Data Exchange (ETDEWEB)

    Lstiburek, J.

    2014-09-01

    The Guide to Attic Air Sealing was completed in 2010 and although not in the standard Measure Guideline format, is intended to be a Measure Guideline on Attic Air Sealing. The guide was reviewed during two industry stakeholders meetings held on December 18th, 2009 and January 15th, 2010, and modified based on the comments received. Please do not make comments on the Building America format of this document. The purpose of the Guide to Attic Air Sealing is to provide information and recommendations for the preparation work necessary prior to adding attic insulation. Even though the purpose of this guide is to save energy - health, safety and durability should not be compromised by energy efficiency. Accordingly, combustion safety and ventilation for indoor air quality are addressed first. Durability and attic ventilation then follow. Finally, to maximize energy savings, air sealing is completed prior to insulating. The guide is intended for home remodelers, builders, insulation contractors, mechanical contractors, general contractors who have previously done remodeling and homeowners as a guide to the work that needs to be done.

  5. A morbillivirus causing mass mortality in seals.

    NARCIS (Netherlands)

    A.D.M.E. Osterhaus (Albert)

    1989-01-01

    textabstractDuring an outbreak of a serious apparently infectious disease among harbour seals (Phoca vitulina), which started in the Kattegat area in April 1988 and rapidly spread to the North sea, the Wadden sea and the Baltic sea, greater than 17,000 animals died within a period of eight months. I

  6. Bearings and Seals. FOS: Fundamentals of Service.

    Science.gov (United States)

    John Deere Co., Moline, IL.

    This manual on bearings and seals is one of a series of power mechanics texts and visual aids for use in training for the servicing of automotive and off-the-road farm and industrial machines. Materials provide basic information and illustrations for use by vocational students and teachers as well as shop servicemen and laymen. Focusing on…

  7. Test of Seal System for Flexible Pipe End Fitting

    DEFF Research Database (Denmark)

    Banke, Lars; Jensen, Thomas Gregers

    1999-01-01

    by compression of the gaskets, thus using the geometry to establish a seal towards the inner liner of the pipe and the steel sleeve of the end fitting. This paper describes how the seal system of an end fitting can be tested using an autoclave. By regulating temperature and pressure, the seal system can...

  8. 14 CFR 1221.102 - Establishment of the NASA Seal.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Establishment of the NASA Seal. 1221.102 Section 1221.102 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION THE NASA SEAL AND OTHER DEVICES, AND THE CONGRESSIONAL SPACE MEDAL OF HONOR NASA Seal, NASA Insignia, NASA Logotype,...

  9. 14 CFR 1221.109 - Use of the NASA Seal.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Use of the NASA Seal. 1221.109 Section 1221.109 Aeronautics and Space NATIONAL AERONAUTICS AND SPACE ADMINISTRATION THE NASA SEAL AND OTHER DEVICES, AND THE CONGRESSIONAL SPACE MEDAL OF HONOR NASA Seal, NASA Insignia, NASA Logotype, NASA...

  10. Analyses toward factors influencing sealing clearance of a metal rubber seal and derivation of a calculation formula

    Institute of Scientific and Technical Information of China (English)

    Yan Hui; Zhao Yalei; Liu Jianguo; Jiang Hongyuan

    2016-01-01

    Sealing clearance is a key factor for a metal rubber seal’s sealability. The expansion coef-ficient and expansion deformation in the radial direction of metal rubber have been obtained through a thermal expansion experiment of metal rubber. The influence of the elastic modulus to the sealing clearance has been analyzed theoretically. By combining the temperature and elasticity factors of metal rubber with the elastic mechanics theory, the calculation formula of the sealing clearance has been derived, and the values of the sealing clearance and the leakage rate in certain working conditions have been calculated. Experimental results are consistent with calculation results in a high degree. The calculation formula of the sealing clearance can explain the influences of the temperature and elastic modulus factors of metal rubber on the sealing clearance. It can pro-vide guidance for the study of sealing mechanism of metal rubber seals.

  11. SU-8 cantilever chip interconnection

    DEFF Research Database (Denmark)

    Johansson, Alicia Charlotte; Janting, Jakob; Schultz, Peter;

    2006-01-01

    the electrodes on the SU-8 chip to a printed circuit board. Here, we present two different methods of electrically connecting an SU-8 chip, which contains a microfluidic network and free-hanging mechanical parts. The tested electrical interconnection techniques are flip chip bonding using underfill or flip chip...... bonding using an anisotropic conductive film (ACF). These are both widely used in the Si industry and might also be used for the large scale interconnection of SU-8 chips. The SU-8 chip, to which the interconnections are made, has a microfluidic channel with integrated micrometer-sized cantilevers...... that can be used for label-free biochemical detection. All the bonding tests are compared with results obtained using similar Si chips. It is found that it is significantly more complicated to interconnect SU-8 than Si cantilever chips primarily due to the softness of SU-8....

  12. Sealed source dismantling hot cell - startup

    Energy Technology Data Exchange (ETDEWEB)

    Dellamano, Jose Claudio; Ferreira, Robson de Jesus, E-mail: jcdellam@ipen.br, E-mail: rojefer@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Gerencia de Rejeitos radioativos

    2013-07-01

    Sealed radioactive sources are widely used in many applications of nuclear technology and at the end of the useful life, most sources become radioactive waste. In Brazil, this waste is received by the Institutes of the National Nuclear Energy Commission and kept under centralized storage. The Waste Management Department at the Nuclear and Energy Research Institute is the main storage center, having received around 20,000 disused sources. A hot cell was designed and constructed to manage Co-60 spent sealed sources with activity up to 3.7 10{sup 1}0 Bq and other sources with equivalent activities. In the hot cell the sources are withdraw from their original shielding and transferred to a standard shielding for further disposal off. The original shielding disassembling is made outside the hot cell and after opening, it is transferred inside the hot cell and the sealed source is removed remotely. The source is checked in relation to external contamination and its activity is checked. After this, the source is positioned in the standard shielding located inside an overpack at the bottom of the hot cell. This paper describes some pre-operational tests carried out in it, that include: opening and closing doors and locks, checking of all electrical and pneumatic controls, the original shielding movement inside the hot-cell, dose rate measurements outside the hot-cell, insertion of the sealed sources inside the activity meter chamber, transferring the sealed source to the standard shielding, movement of the overpack with the standard shielding to outside of the hot-cell and plugging of the standard shielding. (author)

  13. ITER lip seal welding and cutting developments

    Energy Technology Data Exchange (ETDEWEB)

    Levesy, B.; Cordier, J.J.; Jokinen, T. [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France); Kujanpää, V.; Karhu, M. [VTT Technical Research Centre of Finland (Finland); Le Barbier, R. [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France); Määttä, T. [VTT Technical Research Centre of Finland (Finland); Martins, J.P.; Utin, Y. [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France)

    2015-10-15

    Highlights: • Different TIG and Laser welding techniques are tested. • Twin spot laser welding techniques is the best. • Limited heat input gives a stable weld pool in all positions. • Penetrations is achieved. • Lip seal welding and cutting with a robotic arm is successfully performed on a representative mock-up. - Abstract: The welded lip seals form part of the torus primary vacuum boundary in between the port plugs and the vacuum vessel, and are classified as Protection Important Component. In order to refurbish the port plugs or the in-vessel components, port plugs have to be removed from the machine. The lip seal design must enable up to ten opening of the vacuum vessel during the life time operation of the ITER machine. Therefore proven, remote reliable cutting and re-welding are essential, as these operations need to be performed in the port cells in a nuclear environment, where human presence will be restricted. Moreover, the combination of size of the components to be welded (∼10 m long vacuum compatible thin welds) and the congested environment close to the core of the machine constraint the type and size of tools to be used. This paper describes the lip seal cutting and welding development programme performed at the VTT Technical Research Centre, Finland. Potential cutting and welding techniques are analyzed and compared. The development of the cutting, TIG and laser welding techniques on samples are presented. Effects of lip seal misalignments and optimization of the 2 welding processes are discussed. Finally, the manufacturing and test of the two 1.2 m × 1 m representative mock-ups are presented. The set-up and use of a robotic arm for the mock-up cutting and welding operations are also described.

  14. Angel wing seals for blades of a gas turbine and methods for determining angel wing seal profiles

    Science.gov (United States)

    Wang, John Zhiqiang

    2003-01-01

    A gas turbine has buckets rotatable about an axis, the buckets having angel wing seals. The seals have outer and inner surfaces, at least one of which, and preferably both, extend non-linearly between root radii and the tip of the seal body. The profiles are determined in a manner to minimize the weight of the seal bodies, while maintaining the stresses below predetermined maximum or allowable stresses.

  15. Fuzzy Logic Control ASIC Chip

    Institute of Scientific and Technical Information of China (English)

    沈理

    1997-01-01

    A fuzzy logic control VLSI chip,F100,for industry process real-time control has been designed and fabricated with 0.8μm CMOS technology.The chip has the features of simplicity,felexibility and generality.This paper presents the Fuzzy control inrerence method of the chip,its VLSI implementation,and testing esign consideration.

  16. Fabrication method for chip-scale-vacuum-packages based on a chip-to-wafer-process

    Science.gov (United States)

    Bauer, J.; Weiler, D.; Ruß, M.; Heß, J.; Yang, P.; Voß, J.; Arnold, N.,; Vogt, H.

    2010-10-01

    This paper introduces a simple vacuum packaging method which is based on a Chip-to-Wafer process. The MEMS-device is provided with an electroplated solder frame. A Si-lid with the same solder frame is mounted on each die of the wafer using a flip chip process. The same materials for lid and substrate are used in order to reduce the mechanical stress due to the same thermal coefficients of expansion. The resulting cavity between die and lid can be evacuated and hermetically sealed with an eutectic soldering process. The feasibility of the method is demonstrated with an infrared focal plane array (IR-FPA). In this case, the Si-lid acts as an optical window and contains an anti reflective layer for the 8-14 μm wavelength area on both sides. The long-term vacuum stability is supported by a getter film inside the package. This method simplifies the sawing process and has the additional cost benefit that it is possible to package only known good dies.

  17. Experimental toxoplasma gondii infection in grey seals (Halichoerus grypus)

    DEFF Research Database (Denmark)

    Gajadhar, A. A.; Measures, L.; Forbes, L. B.;

    2004-01-01

    changes were observed in all inoculated seals but not in control animals. A modified agglutination test revealed the presence of antibodies to T. gondii in sera collected from inoculated seals and mice inoculated as controls. No evidence of the parasite was found on an extensive histological examination......Laboratory-reared animals were used to assess the susceptibility of seals (Halichoerus grypus) to Toxoplasma gondii infection. Four seals were each orally inoculated with 100 or 10,000 oocysts of T. gondii (VEG strain), and another 4 seals served as negative controls. Occasionally, mild behavioral...

  18. Investigation of seal technology for Francis turbine

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Wei

    2012-06-01

    Leakage loss and disk friction loss caused by the clearance gap flow at the back of a runner have a major impact on the efficiency of hydraulic turbines. Accordingly, it is extremely important to develop and improve the seal technology by investigating the gap flow. Generally, there are two types of the gap flow: axial gap flow between a rotating disk and a stator (e.g. the flow at the back of a runner) and the annular gap flow (e.g. the flow at an annular seal). Firstly, the overview of previous researches on labyrinth seal, rotating disk flow and Taylor-Couette flow are summarized. Labyrinth seals are the primary type of seals for turbo machinery. However, most researchers studied it for compressible flow only. It is also found that the enclosed rotating disk flow with through-flow can be studied instead of the gap flow in a hydraulic machine. Furthermore, the above mentioned annular gap flow is similar to the Taylor-Couette flow. The Taylor-vortices are formed in the annular gap due to the rotation of disk, which could be used as a resistance of flow. Therefore, in the present work, three parts are investigated. The first part is the investigation of the labyrinth seal for Francis turbines. The second part is the investigation of the gap flow between two stationary walls. The third part is investigation of the annular gap flow between one stationary and one rotating wall, based on the theory of Taylor-Couette flow. Afterwards, the theoretical formulas for leakage flow of a traditional labyrinth seal used in high head Francis turbine is derived and is verified to give acceptable results. The theoretical model is useful to predict the leakage flow by the measurements of Francis turbine at the Aabjoera Power plant. For straight-through labyrinth seal, the effects of cavity dimensions, numbers and locations on the leakage flow are investigated numerically. Smaller cavity depth, longer cavity length and fewer cavity numbers are required in order to reduce leakage

  19. Impedance spectra of patch clamp scenarios for single cells immobilized on a lab-on-a-chip

    DEFF Research Database (Denmark)

    Alberti, Massimo; Snakenborg, Detlef; Lopacinska, Joanna M.

    2014-01-01

    and simulated impedance spectra proved that the presented method could distinguish between a cell-attached mode and a whole-cell mode even with low-quality seals. In physiological conditions, the capacitance of HeLa cells was measured to *38 pF. The first gigaseal was recorded and maintained for 40 min. Once...... membrane. After incubating the chip for 24 h, HeLa cells adhered and grew on the chip surface but did not survive when trapped on the microapertures. The microfluidic system proved to work as a micro electrophysiological analysis system, and the IS-based method can be used for further studies on the post...

  20. Low torque hydrodynamic lip geometry for rotary seals

    Energy Technology Data Exchange (ETDEWEB)

    Dietle, Lannie L.; Schroeder, John E.

    2015-07-21

    A hydrodynamically lubricating geometry for the generally circular dynamic sealing lip of rotary seals that are employed to partition a lubricant from an environment. The dynamic sealing lip is provided for establishing compressed sealing engagement with a relatively rotatable surface, and for wedging a film of lubricating fluid into the interface between the dynamic sealing lip and the relatively rotatable surface in response to relative rotation that may occur in the clockwise or the counter-clockwise direction. A wave form incorporating an elongated dimple provides the gradual convergence, efficient impingement angle, and gradual interfacial contact pressure rise that are conducive to efficient hydrodynamic wedging. Skewed elevated contact pressure zones produced by compression edge effects provide for controlled lubricant movement within the dynamic sealing interface between the seal and the relatively rotatable surface, producing enhanced lubrication and low running torque.

  1. Method of making hermetic seals for hermetic terminal assemblies

    Science.gov (United States)

    Hsu, John S.; Marlino, Laura D.; Ayers, Curtis W.

    2010-04-13

    This invention teaches methods of making a hermetic terminal assembly comprising the steps of: inserting temporary stops, shims and jigs on the bottom face of a terminal assembly thereby blocking assembly core open passageways; mounting the terminal assembly inside a vacuum chamber using a temporary assembly perimeter seal and flange or threaded assembly interfaces; mixing a seal admixture and hardener in a mixer conveyor to form a polymer seal material; conveying the polymer seal material into a polymer reservoir; feeding the polymer seal material from the reservoir through a polymer outlet valve and at least one polymer outlet tube into the terminal assembly core thereby filling interstitial spaces in the core adjacent to service conduits, temporary stop, and the terminal assembly casing; drying the polymer seal material at room temperature thereby hermetically sealing the core of the terminal assembly; removing the terminal assembly from the vacuum chamber, and; removing the temporary stops, shims.

  2. Dimensional Analysis on Resistance Characteristics of Labyrinth Seals

    Institute of Scientific and Technical Information of China (English)

    HU Dongxu; JIA Li; YANG Lixin

    2014-01-01

    Experimental investigation of stepped and straight-through labyrinth seals was designed to study the sealing performance of two different typical labyrinth seals.In order to facilitate dimensional analysis on the flow resistance characteristics of labyrinth seals,the variable cross-section of the flow channels are considered as constant cross-section flow.The mechanical energy loss of flow caused by throttle turbulence intensity is considered as caused by friction along the way.The friction coefficient of stepped labyrinth seals is bigger than that of straight-through labyrinth seals by more than 40% for the same Reynolds number and the ratio of equivalent diameter and the seal length.The expression of friction coefficient f and fRe are obtained from experimental data.The verifications indicate that the expressions are highly accurate.The contribution to the total pressure drop of each tooth cavity gradually becomes less along the flow direction.

  3. Apparatus and method for inspecting a sealed container

    Science.gov (United States)

    Harmon, J Frank [Pocatello, ID; Jones, James L [Idaho Falls, ID; Hunt, Alan W [Pocatello, ID; Spaulding, Randy J [Pocatello, ID; Smith, Michael [Phoenix, AZ

    2009-03-24

    An apparatus for inspecting a sealed container is disclosed and which includes a pulsed electron accelerator which is positioned in spaced relation relative to a first side of the sealed container, and which produces a pulsed beam of photons which passes through the sealed container and any contents enclosed within the sealed container; a detector positioned in spaced relation relative to a second, opposite side of the sealed container, and which receives the pulsed beam of photons which passes through the contents of the sealed container, and which produces an output signal; and a computer for developing a visible image from the output signal of the detector which depicts the contents of the sealed container.

  4. Seals/Secondary Fluid Flows Workshop 1997; Volume I

    Science.gov (United States)

    Hendricks, Robert C. (Editor)

    2006-01-01

    The 1997 Conference provided discussions and data on (a) program overviews, (b) developments in seals and secondary air management systems, (c) interactive seals flows with secondary air or fluid flows and powerstream flows, (d) views of engine externals and limitations, (e) high speed engine research sealing needs and demands, and (f) a short course on engine design development margins. Sealing concepts discussed include, mechanical rim and cavity seals, leaf, finger, air/oil, rope, floating-brush, floating-T-buffer, and brush seals. Engine externals include all components of engine fluid systems, sensors and their support structures that lie within or project through the nacelle. The clean features of the nacelle belie the minefield of challenges and opportunities that lie within. Seals; Secondary air flows; Rotordynamics; Gas turbine; Aircraft; CFD; Testing; Turbomachinery

  5. Influence of ceramic package internal components on the performance of vacuum sealed uncooled bolometric detectors

    Science.gov (United States)

    Paquet, Alex; Deshaies, Sébastien; Desroches, Yan; Whalin, Jeff; Topart, Patrice

    2013-03-01

    INO has developed a hermetic vacuum packaging technology for uncooled bolometric detectors based on ceramic leadless chip carriers (LCC). Cavity pressures less than 3 mTorr are obtained. Processes are performed in a state-of-the art semi-automated vacuum furnace that allows for independent activation of non-evaporable thin film getters. The getter activation temperature is limited by both the anti-reflection coated silicon or germanium window and the MEMS device built on CMOS circuits. Temperature profiles used to achieve getter activation and vacuum sealing were optimized to meet lifetime and reliability requirements of packaged devices. Internal package components were carefully selected with respect to their outgassing behavior so that a good vacuum performance was obtained. In this paper, INO's packaging process is described. The influence of various package internal components, in particular the CMOS circuits, on vacuum performance is presented. The package cavity pressure was monitored using INO's pressure microsensors and the gas composition was determined by internal vapor analysis. Lifetime was derived from accelerated testing after storage of packaged detectors at various temperatures from room temperature to 120°C. A hermeticity yield over 80% was obtained for batches of twelve devices packaged simultaneously. Packaged FPAs submitted to standard MIL-STD-810 reliability testing (vibration, shock and temperature cycling) exhibited no change in IR response. Results show that vacuum performance strongly depends on CMOS circuit chips. Detectors packaged using a thin film getter show no change in cavity pressure after storage for more than 30 days at 120°C. Moreover, INO's vacuum sealing process is such that even without a thin film getter, a base pressure of less than 10 mTorr is obtained and no pressure change is observed after 40 days at 85°C.

  6. Trapping molecules on chips

    CERN Document Server

    Santambrogio, Gabriele

    2015-01-01

    In the last years, it was demonstrated that neutral molecules can be loaded on a microchip directly from a supersonic beam. The molecules are confined in microscopic traps that can be moved smoothly over the surface of the chip. Once the molecules are trapped, they can be decelerated to a standstill, for instance, or pumped into selected quantum states by laser light or microwaves. Molecules are detected on the chip by time-resolved spatial imaging, which allows for the study of the distribution in the phase space of the molecular ensemble.

  7. Titanium based flat heat pipes for computer chip cooling

    Science.gov (United States)

    Soni, Gaurav; Ding, Changsong; Sigurdson, Marin; Bozorgi, Payam; Piorek, Brian; MacDonald, Noel; Meinhart, Carl

    2008-11-01

    We are developing a highly conductive flat heat pipe (called Thermal Ground Plane or TGP) for cooling computer chips. Conventional heat pipes have circular cross sections and thus can't make good contact with chip surface. The flatness of our TGP will enable conformal contact with the chip surface and thus enhance cooling efficiency. Another limiting factor in conventional heat pipes is the capillary flow of the working fluid through a wick structure. In order to overcome this limitation we have created a highly porous wick structure on a flat titanium substrate by using micro fabrication technology. We first etch titanium to create very tall micro pillars with a diameter of 5 μm, a height of 40 μm and a pitch of 10 μm. We then grow a very fine nano structured titania (NST) hairs on all surfaces of the pillars by oxidation in H202. In this way we achieve a wick structure which utilizes multiple length scales to yield high performance wicking of water. It's capable of wicking water at an average velocity of 1 cm/s over a distance of several cm. A titanium cavity is laser-welded onto the wicking substrate and a small quantity of water is hermetically sealed inside the cavity to achieve a TGP. The thermal conductivity of our preliminary TGP was measured to be 350 W/m-K, but has the potential to be several orders of magnitude higher.

  8. Advanced Bristle Seals for Gas Turbine Engines

    Science.gov (United States)

    1993-01-28

    test sequence I retained the .003 inch shim and added a positive seal between the shim stock and the housing using Room Temperature Vulcanizing (RTV...113.4 200 6 1.131 1.040 175.142 0.219 * STANDARD CUBIC FOOT PER MINUTE u FLOW(cfm) OF AIR 2 70F/14.7psil TABLE C-8. TESI SEQUENCE H DATA "H. STATIC

  9. Shrink-Fit Solderable Inserts Seal Hermetically

    Science.gov (United States)

    Croucher, William C.

    1992-01-01

    Shrink-fit stainless-steel insert in aluminum equipment housing allows electrical connectors to be replaced by soldering, without degrading hermeticity of housing or connector. Welding could destroy electrostatic-sensitive components and harm housing and internal cables. Steel insert avoids problems because connector soldered directly to it rather than welded to housing. Seals between flange and housing, and between connector and flange resistant to leaks, even after mechanical overloading and thermal shocking.

  10. How do seal whiskers suppress vortex shedding

    Science.gov (United States)

    Rinehart, Aidan; Flaherty, Justin; Bunjavick, Joseph; Shyam, Vikram; Zhang, Wei

    2016-11-01

    Certain seal whiskers possess a unique geometry that significantly reduces the vortex-induced vibration; which has attracted great attention to understand how the unique shape re-organizes the wake structure and its potential for passive flow control. The shape of the whiskers can be described as an elliptical cross-section that is lofted along the length of the whisker. Along the entire length of the whisker the ellipse varies in major and minor axis as well as angle of incidence with respect to the axis of the whisker. Of particular interest in this study is to identify what effect the angle of incidence has on the flow structure around the whisker, which has been overlooked in the past. The study will analyze the wake structure behind various scaled-up whisker models using particle image velocimitry (PIV). These whisker models share common geometry dimensions except for the angle of incidence. Flow conditions are created in a water channel and a wind tunnel, covering a wide range of Reynolds number (a few hundreds to thousands), similar to the ambient flow environment of seals and to the targeted aero-propulsion applications. This study will help address knowledge gaps in understanding of how certain geometry features of seal whiskers influence the wake and establish best practices for its application as effective passive flow control strategy.

  11. CENTRIFUGAL PUMP AND SHAFT SEALING MEANS

    Science.gov (United States)

    Rushing, F.C.

    1960-09-01

    A description is given of sealing means between a hollow rotatable shaft and a stationary member surrounding the shaft which defines therewith a sealing space of annular cross-section, comprising a plurality of axially spaced rings held against seats by ring springs which serve to subdivide the sealing space- into a plurality of zones. Process gas introduced into the hollow shaft through a port communicating with a centrally located zone which iu turn communicates with a bore in the sleeve, is removed from the shaft through a second port communicating with an adjacent central zone and discharged through a second bore. A sealant gas is supplied to an end zone under a pressure sufficient to cause it to flow axially into adjacent zones and then maintained at a lower pressure than either the sealant gas source or the process gas inlet zone, preventing the sealant gas from entering the shaft and allowing gases leaking into the sealant gas to be withdrawn and led to a separator.

  12. Cytometer on a Chip

    Science.gov (United States)

    Fernandez, Salvador M.

    2011-01-01

    A cytometer now under development exploits spatial sorting of sampled cells on a microarray chip followed by use of grating-coupled surface-plasmon-resonance imaging (GCSPRI) to detect the sorted cells. This cytometer on a chip is a prototype of contemplated future miniature cytometers that would be suitable for rapidly identifying pathogens and other cells of interest in both field and laboratory applications and that would be attractive as alternatives to conventional flow cytometers. The basic principle of operation of a conventional flow cytometer requires fluorescent labeling of sampled cells, stringent optical alignment of a laser beam with a narrow orifice, and flow of the cells through the orifice, which is subject to clogging. In contrast, the principle of operation of the present cytometer on a chip does not require fluorescent labeling of cells, stringent optical alignment, or flow through a narrow orifice. The basic principle of operation of the cytometer on a chip also reduces the complexity, mass, and power of the associated laser and detection systems, relative to those needed in conventional flow cytometry. Instead of making cells flow in single file through a narrow flow orifice for sequential interrogation as in conventional flow cytometry, a liquid containing suspended sampled cells is made to flow over the front surface of a microarray chip on which there are many capture spots. Each capture spot is coated with a thin (approximately 50-nm) layer of gold that is, in turn, coated with antibodies that bind to cell-surface molecules characteristic of one the cell species of interest. The multiplicity of capture spots makes it possible to perform rapid, massively parallel analysis of a large cell population. The binding of cells to each capture spot gives rise to a minute change in the index of refraction at the surface of the chip. This change in the index of refraction is what is sensed in GCSPRI, as described briefly below. The identities of the

  13. Experiment list: SRX122496 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available || chip antibody=Rel || treatment=LPS || time=120 min || chip antibody manufacturer 1=Santa Cruz || chip ant...ibody catalog number 1=sc-71 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc

  14. Bipolar electrosurgical vessel-sealing device with compressive force monitoring.

    Science.gov (United States)

    Chen, Roland K; Chastagner, Matthew W; Geiger, James D; Shih, Albert J

    2014-06-01

    Bipolar electrosurgical vessel sealing is commonly used in surgery to perform hemostasis. The electrode compressive force is demonstrably an important factor affecting the vessel seal burst pressure, an index of the seal quality. Using a piezoresistive force sensor attached to the handle of a laparoscopic surgical device, applied handle force was measured and used to predict the electrosurgical vessel compressive force and the pressure at the electrode. The sensor enables the monitoring of vessel compressive force during surgery. Four levels of compressive force were applied to seal three types of porcine vessels (carotid artery, femoral artery, and jugular vein). The burst pressure of the vessel seal was tested to evaluate the seal quality. Compressive pressure was found to be a statistically significant factor affecting burst pressure for femoral arteries and jugular veins. Vessels sealed with low compressive pressure (<300 kPa) have a higher failure rate (burst pressure<100 mm Hg) than vessels sealed with high compressive pressure. An adequate compressive force is required to generate the compressive pressure needed to form a seal with high burst pressure. A laparoscopic surgical device with compressive force monitoring capability can help ensure adequate compressive pressure, vessel burst pressure, and quality of seal.

  15. Sharks shape the geometry of a selfish seal herd: experimental evidence from seal decoys.

    Science.gov (United States)

    De Vos, Alta; O'Riain, M Justin

    2010-02-23

    Many animals respond to predation risk by forming groups. Evolutionary explanations for group formation in previously ungrouped, but loosely associated prey have typically evoked the selfish herd hypothesis. However, despite over 600 studies across a diverse array of taxa, the critical assumptions of this hypothesis have remained collectively untested, owing to several confounding problems in real predator-prey systems. To solve this, we manipulated the domains of danger of Cape fur seal (Arctocephalus pusillus pusillus) decoys to provide evidence that a selfish reduction in a seals' domain of danger results in a proportional reduction in its predation risk from ambush shark attacks. This behaviour confers a survival advantage to individual seals within a group and explains the evolution of selfish herds in a prey species. These findings empirically elevate Hamilton's selfish herd hypothesis to more than a 'theoretical curiosity'.

  16. Radiometer on a Chip

    Science.gov (United States)

    Chattopadhyay, Goutam; Gill, John J.; Mehdi, Imran; Lee, Choonsup; Schlecht, Erich T.; Skalare, Anders; Ward, John S.; Siegel, Peter H.; Thomas, Bertrand C.

    2009-01-01

    The radiometer on a chip (ROC) integrates whole wafers together to p rovide a robust, extremely powerful way of making submillimeter rece ivers that provide vertically integrated functionality. By integratin g at the wafer level, customizing the interconnects, and planarizing the transmission media, it is possible to create a lightweight asse mbly performing the function of several pieces in a more conventiona l radiometer.

  17. Mikrofluidik-Chips

    NARCIS (Netherlands)

    Verpoorte, E.; Lichtenberg, J.

    2000-01-01

    Microfluidic chips are becoming the new paradigm for chemical processing and analysis in the laboratory. Hair-fine channels made in planar substrates using silicon processing technologies replace beakers and tubing for automated liquid transport and handling on a sub-μ L scale. Reduced conduit diame

  18. MICROELECTRONICS: Flip the Chip.

    Science.gov (United States)

    Wong, C P; Luo, S; Zhang, Z

    2000-12-22

    As integrated circuit fabrication advances rapidly and the market for faster, lighter, smaller, yet less expensive electronic products accelerates, electronic packaging faces its own challenges. In this Perspective, Wong, Luo, and Zhang describe recent advances in flip chip packaging. This technology has many advantages over the conventional wire bonding technology and offers the possibility of low-cost electronic assembly for modern electronic products.

  19. [Wood chip alveolitis].

    Science.gov (United States)

    Müller-Wening, D; Renck, T; Neuhauss, M

    1999-07-01

    A 52 year old farmer was referred to us for investigation of suspected farmer's lung. For many years the farmer had been exposed to hay, straw, pigeons, and fuel chip dust. Under exertion he suffered from shortness of breath. In the farmer's own fuel chips we could identify Aspergillus fumigatus, Paecilomyces species and Mucor species. In the farmer's blood we found IgG-antibodies against his own fuel chips, thermophilic actinomycetes, Penicillium species, Mucor species and Aspergillus fumigatus. We did not detect any IgG-antibodies against pigeon serum or pigeon faeces. In order to determine the responsible allergen we performed two challenge tests. In the first test the farmer had to inhale his own hay and straw dust for one hour. This provocation was negative. A second one-hour inhalative challenge was carried out 16 days later using his own fuel chips. This time he experienced significant pulmonary and systemic reactions: body temperature rose by 3.3 degrees C, leucocytes by 12,200/mm3; PO2 fell by 39.4 mmHg, vital capacity by 52%, DLCO by 36%. After the challenge the farmer complained of coughing and dyspnoea. Rales could be heard on auscultation, and an interstitial infiltrate was seen to develop on chest x-rays. After the challenge the patient had to be treated with oxygen and systemic corticosteroids. We diagnosed a fuel chip-induced exogenous allergic alveolitis (EAA). Eight days later the parameters were back to normal and the farmer was discharged from our hospital with further corticosteroid medication. This method of inhalative provocation is very important in diagnosing an EAA. Problems arise when the mode and duration of exposure to substances has to be chosen. Because of the risk of severe reactions, inhalative provocations relating to EAAs should only be performed in special centres with an intensive care unit. In this paper we present a diagnosis of fuel chip lung, which is rarely seen in Germany. However, with the rising use of fuel chips as

  20. Preservation of forest wood chips

    Energy Technology Data Exchange (ETDEWEB)

    Kofman, P.D.; Thomsen, I.M.; Ohlsson, C.; Leer, E.; Ravn Schmidt, E.; Soerensen, M.; Knudsen, P.

    1999-01-01

    As part of the Danish Energy Research Programme on biomass utilisation for energy production (EFP), this project concerns problems connected to the handling and storing of wood chips. In this project, the possibility of preserving wood chips of the Norway Spruce (Picea Abies) is addressed, and the potential improvements by anaerobic storage are tested. Preservation of wood chips aims at reducing dry matter losses from extensive heating during storage and to reduce production of fungal spores. Fungal spores pose a health hazards to workers handling the chips. Further the producers of wood chips are interested in such a method since it would enable them to give a guarantee for the delivery of homogeneous wood chips also during the winter period. Three different types of wood chips were stored airtight and further one of these was stored in accordance with normal practise and use as reference. The results showed that airtight storage had a beneficial impact on the quality of the chips: no redistribution of moisture, low dry matter losses, unfavourable conditions for microbial activity of most fungi, and the promotion of yeasts instead of fungi with airborne spores. Likewise the firing tests showed that no combustion problems, and no increased risk to the environment or to the health of staff is caused by anaerobic storage of wood chips. In all, the tests of the anaerobic storage method of forest wood chips were a success and a large-scale test of the method will be carried out in 1999. (au)

  1. Phocid seals, seal lice and heartworms: a terrestrial host-parasite system conveyed to the marine environment.

    Science.gov (United States)

    Leidenberger, Sonja; Harding, Karin; Härkönen, Tero

    2007-10-15

    Adaptation of pinnipeds to the marine habitat imposed parallel evolutions in their parasites. Ancestral pinnipeds must have harboured sucking lice, which were ancestors of the seal louse Echinophthirius horridus. The seal louse is one of the few insects that successfully adjusted to the marine environment. Adaptations such as keeping an air reservoir and the ability to hold on to and move on the host were necessary, as well as an adjustment of their life cycle to fit the diving habits of their host. E. horridus are confined to the Northern Hemisphere and have been reported from 9 species of northern phocids belonging to 4 genera, including land-locked seal species. The transmission from seal to seal is only possible when animals are hauled-out on land or ice. Lice are rarely found on healthy adult seals, but frequently on weak and young animals. The seal louse is suggested to play an important role as an intermediate host transmitting the heartworm Acanthocheilonema spirocauda among seals. However, the evidence is restricted to a single study where the first 3 larval stages of the heartworm were shown to develop in the louse. The fourth-stage larvae develop in the blood system of seals and eventually transform into the adult stage that matures in the heart. Since all other studies failed to confirm the presence of heartworm larvae in seal lice, other unknown intermediate hosts could be involved in the transmission of the heartworm. Transplacental transmission of microfilariae in seals has been suggested as an additional possibility, but is not likely to be important since the occurrence of heartworms in adult seals is very rare compared with juveniles. Furthermore, there are no findings of the first 3 larval stages in seals. This review shows that the heartworm infects nearly the same species of seals as the seal louse, except for the grey seal Halichoerus grypus, where the heartworm is absent. Prevalence and intensity of infection differ among regions in the

  2. Apartment Compartmentalization With an Aerosol-Based Sealing Process

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, S. [Consortium for Advanced Residential Buildings, Norwalk, CT (United States); Berger, D. [Consortium for Advanced Residential Buildings, Norwalk, CT (United States); Harrington, C. [Consortium for Advanced Residential Buildings, Norwalk, CT (United States)

    2015-03-01

    Air sealing of building enclosures is a difficult and time-consuming process. Current methods in new construction require laborers to physically locate small and sometimes large holes in multiple assemblies and then manually seal each of them. The innovation demonstrated under this research study was the automated air sealing and compartmentalization of buildings through the use of an aerosolized sealant, developed by the Western Cooling Efficiency Center at University of California Davis. CARB sought to demonstrate this new technology application in a multifamily building in Queens, NY. The effectiveness of the sealing process was evaluated by three methods: air leakage testing of overall apartment before and after sealing, point-source testing of individual leaks, and pressure measurements in the walls of the target apartment during sealing.

  3. Field Trial of an Aerosol-Based Enclosure Sealing Technology

    Energy Technology Data Exchange (ETDEWEB)

    Harrington, Curtis [Univ. of California, Davis, CA (United States); Springer, David [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States)

    2015-09-01

    This report presents the results from several demonstrations of a new method for sealing building envelope air leaks using an aerosol sealing process developed by the Western Cooling Efficiency Center at UC Davis. The process involves pressurizing a building while applying an aerosol sealant to the interior. As air escapes through leaks in the building envelope, the aerosol particles are transported to the leaks where they collect and form a seal that blocks the leak. Standard blower door technology is used to facilitate the building pressurization, which allows the installer to track the sealing progress during the installation and automatically verify the final building tightness. Each aerosol envelope sealing installation was performed after drywall was installed and taped, and the process did not appear to interrupt the construction schedule or interfere with other trades working in the homes. The labor needed to physically seal bulk air leaks in typical construction will not be replaced by this technology.

  4. A New Design of Magnetic Fluid Seal for Liquids

    Institute of Scientific and Technical Information of China (English)

    LIU Tong-gang; YANG Zhi-yi

    2005-01-01

    Direct contract between the sealed liquid and the magnetic fluid in a dynamic system under magnetic field may lead to an unstable interface, consequently, break down the seal. Aiming at this problem, a new magnetic fluid seal (MFS) was developed. In this new MFS, a soft iron bushing with high permeability was introduced on the shaft and nonferrous shields were installed beside the bushing and the pole pieces. The parameters of the bushing and the shields were optimized in a seal simulation facility. The results show that the bushing with a thickness of 7 mm and shields with a width of 8 mm are best for sealing a shaft 20 mm in diameter. The MFS designed based on the optimum parameters shows good performance and long life span for sealing lubricating oil.

  5. Condition monitoring of reciprocating seal based on FBG sensors

    Science.gov (United States)

    Zhao, Xiuxu; Zhang, Shuanshuan; Wen, Pengfei; Zhen, Wenhan; Ke, Wei

    2016-07-01

    The failure of hydraulic reciprocating seals will seriously affect the normal operation of hydraulic reciprocating machinery, so the potential fault condition monitoring of reciprocating seals is very important. However, it is extremely difficult because of the limitation of reciprocating motion and the structure constraints of seal groove. In this study, an approach using fiber Bragg grating (FBG) sensors is presented. Experimental results show that the contact strain changes of a reciprocating seal can be detected by FBG sensors in the operation process of the hydraulic cylinders. The failure condition of the reciprocating seal can be identified by wavelet packet energy entropy, and the center frequency of power spectrum analysis. It can provide an effective solution for the fault prevention and health management of reciprocating hydraulic rod seals.

  6. Method of forming shrink-fit compression seal

    Science.gov (United States)

    Podgorski, T. J. (Inventor)

    1977-01-01

    A method for making a glass-to-metal seal is described. A domed metal enclosure having a machined seal ring is fitted to a glass post machined to a slight taper and to a desired surface finish. The metal part is then heated by induction in a vacuum. As the metal part heats and expands relative to the glass post, the metal seal ring, possessing a higher coefficient of expansion than the glass post, slides down the tapered post. Upon cooling, the seal ring crushes against the glass post forming the seal. The method results in a glass-to-metal seal possessing extremely good leak resistance, while the parts are kept clean and free of the contaminants.

  7. Pressure actuated film riding seals for turbo machinery

    Energy Technology Data Exchange (ETDEWEB)

    Bidkar, Rahul Anil; Thatte, Azam Mihir; Gibson, Nathan Evan McCurdy; Giametta, Andrew Paul

    2015-08-25

    A seal assembly for a rotary machine is provided. The seal assembly includes multiple sealing device segments disposed circumferentially intermediate to a stationary housing and a rotor. Each of the sealing device segments includes a stator interface element, a shoe plate having an extended portion having one or more labyrinth teeth facing the rotor and a load bearing portion, wherein the shoe plate is configured to generate an aerodynamic force between the shoe plate and the rotor. The sealing device segment further includes a secondary seal configured to be in contact with the stator interface element at a radially outer end and configured to be in contact with an elevated nose section of the extended portion of the shoe plate on a radially inner end; and multiple flexible elements attached to the shoe plate and to the stator interface element.

  8. Characterizing fluidic seals for on-board reagent delivery

    Science.gov (United States)

    Inamdar, Tejas; Anthony, Brian W.

    2013-03-01

    The reagent delivery mechanism in a point-of-care, HIV diagnostic, microfluidic device is studied. Reagents held in an aluminum blister pack are released on the opening of a fluidic seal. The fluidic seals, controlling the flow of reagents, are characterized to reduce anomalies in the desired flow pattern. The findings of this research can be divided into three categories - 1) bonding phenomenon 2) influence of seal pattern on flow and rupture mechanics and 3) process parameters which minimize flow anomalies. Four seal patterns - line hemisphere, line flat, chevron hemisphere and chevron flat were created and tested for reagent delivery using a flow sensor and a force gauge. Experiments suggest that one of the patterns - line-flat - inducted the fewest flow anomalies. A parameter scoping exercise of the seal manufacturing process parameters (temperature, time, pressure) was performed for the line flat seal. Temperature, time, pressure / gap and distance settings which minimize flow anomalies were found.

  9. Apartment Compartmentalization With an Aerosol-Based Sealing Process

    Energy Technology Data Exchange (ETDEWEB)

    Maxwell, Sean [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Berger, David [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Harrington, Curtis [Univ. of California, Davis, CA (United States)

    2015-03-01

    The U.S. Department of Energy Building America Team, Consortium for Advanced Residential Buildings, sought to demonstrate this new technology application in a new construction multifamily building in Queens, New York. The effectiveness of the sealing process was evaluated by three methods: air leakage testing of overall apartment before-and-after sealing, point-source testing of individual leaks, and pressure measurements in the walls of an apartment during sealing.

  10. Develop Efficient Leak Proof M1 Abrams Plenum Seal

    Science.gov (United States)

    2014-05-07

    UNCLASSIFIED UNCLASSIFIED ER-GLSV11389-001.docx Develop Efficient Leak Proof M1 Abrams Plenum Seal SBIR Phase I: Topic A13-061...Leak Proof M1 Abrams Plenum Seal Christian Muehfeld Steve Pennala Great Lakes Sound & Vibration, Inc. 47140 North Main Street Houghton, MI 49931 ER...061. The purpose of this report is to show the feasibility of developing an efficient, leak proof plenum seal for the M1 Abrams . It also shows the

  11. Hardness testing of some fissure-sealing materials.

    Science.gov (United States)

    Ulvestad, H

    1977-11-01

    The mechanical properties of fissure-sealing materials are of significant importance for their durability, i.e. their wear resistance. One of the methods of evaluating a material's resistance to attrition is to apply a hardness test. In the present investigation, the surface hardness of some fissure-sealing materials was tested. Sealants made from diluted composite materials and with inclusion of inorganic filler particles appeared to have a considerable higher surface hardness than the other sealing materials tested.

  12. Hydraulic forces caused by annular pressure seals in centrifugal pumps

    Science.gov (United States)

    Iino, T.; Kaneko, H.

    1980-01-01

    The hydraulic forces caused by annular pressure seals were investigated. The measured inlet and exit loss coefficients of the flow through the seals were much smaller than the conventional values. The results indicate that the damping coefficient and the inertia coefficient of the fluid film in the seal are not affected much by the rotational speed or the eccentricity of the rotor, though the stiffness coefficient seemed to be influenced by the eccentricity.

  13. Integral edge seals for phosphoric acid fuel cells

    Science.gov (United States)

    Granata, Jr., Samuel J. (Inventor); Woodle, Boyd M. (Inventor); Dunyak, Thomas J. (Inventor)

    1992-01-01

    A phosphoric acid fuel cell having integral edge seals formed by an elastomer permeating an outer peripheral band contiguous with the outer peripheral edges of the cathode and anode assemblies and the matrix to form an integral edge seal which is reliable, easy to manufacture and has creep characteristics similar to the anode, cathode and matrix assemblies inboard of the seals to assure good electrical contact throughout the life of the fuel cell.

  14. Twist seal for high-pressure vessels such as space shuttle rocket motors

    Science.gov (United States)

    von Pragenau, George L. (Inventor)

    1989-01-01

    Seals for sealing clevis and flange joints (14) of a solid rocket booster motor, and more particularly to a seal (30) which is twisted upon application of expansion forces to an edge seal (36). This twisting motion initially causes a leading edge seal (44) to be urged into sealing engagement with a surface (48) of an adjacent member (20) and thereafter, increasing fluid pressure on a pressurized side (64) of a seal (30) drives a broad sealing region (46) into sealing engagement with a surface (48).

  15. Influence analysis of secondary O-ring seals in dynamic behavior of spiral groove gas face seals

    Science.gov (United States)

    Hu, Songtao; Huang, Weifeng; Liu, Xiangfeng; Wang, Yuming

    2016-05-01

    The current research on secondary O-ring seals used in mechanical seals has begun to focus on their dynamic properties. However, detailed analysis of the dynamic properties of O-ring seals in spiral groove gas face seals is lacking. In particular a transient study and a difference analysis of steady-state and transient performance are imperative. In this paper, a case study is performed to gauge the effect of secondary O-ring seals on the dynamic behavior (steady-state performance and transient performance) of face seals. A numerical finite element method (FEM) model is developed for the dynamic analysis of spiral groove gas face seals with a flexibly mounted stator in the axial and angular modes. The rotor tilt angle, static stator tilt angle and O-ring damping are selected to investigate the effect of O-ring seals on face seals during stable running operation. The results show that the angular factor can be ignored to save time in the simulation under small damping or undamped conditions. However, large O-ring damping has an enormous effect on the angular phase difference of mated rings, affecting the steady-state performance of face seals and largely increasing the possibility of face contact that reduces the service life of face seals. A pressure drop fluctuation is carried out to analyze the effect of O-ring seals on the transient performance of face seals. The results show that face seals could remain stable without support stiffness and O-ring damping during normal stable operation but may enter a large-leakage state when confronting instantaneous fluctuations. The oscillation-amplitude shortening effect of O-ring damping on the axial mode is much greater than that on the angular modes and O-ring damping prefers to cater for axial motion at the cost of angular motion. This research proposes a detailed dynamic-property study of O-ring seals in spiral groove gas face seals, to assist in the design of face seals.

  16. An ideal sealed source life-cycle

    Energy Technology Data Exchange (ETDEWEB)

    Tompkins, Joseph Andrew [Los Alamos National Laboratory

    2009-01-01

    In the last 40 years, barriers to compliant and timely disposition of radioactive sealed sources have become apparent. The story starts with the explosive growth of nuclear gauging technologies in the 1960s. Dozens of companies in the US manufactured sources and many more created nuclear solutions to industrial gauging problems. Today they do not yet know how many Cat 1, 2, or 3 sources there are in the US. There are, at minimum, tens of thousands of sources, perhaps hundreds of thousands of sources. Affordable transportation solutions to consolidate all of these sources and disposition pathways for these sources do not exist. The root problem seems to be a lack of necessary regulatory framework that has allowed all of these problems to accumulate with no national plan for solving the problem. In the 1960s, Pu-238 displaced Pu-239 for most neutron and alpha source applications. In the 1970s, the availability of inexpensive Am-241 resulted in a proliferation of low energy gamma sources used in nuclear gauging, well logging, pacemakers, and X-ray fluorescence applications for example. In the 1980s, rapid expansion of worldwide petroleum exploration resulted in the expansion of Am-241 sources into international locations. Improvements of technology and regulation resulted in a change in isotopic distribution as Am-241 made Pu-239 and Pu-238 obsolete. Many early nuclear gauge technologies have been made obsolete as they were replaced by non-nuclear technoogies. With uncertainties in source end of life disposition and increased requirements for sealed source security, nuclear gauging technology is the last choice for modern process engineering gauging solutions. Over the same period, much was learned about licensing LLW disposition facilities as evident by the closure of early disposition facilities like Maxey Flats. The current difficulties in sealed source disposition start with adoption of the NLLW policy act of 1985, which created the state LLW compact system they

  17. STUDY ON RECIPROCATING SEALS FOR A LARGER DIAMETER AXIAL PISTON

    Institute of Scientific and Technical Information of China (English)

    Yang Jian; Yang Huayong; Xu Bing

    2004-01-01

    Sealing performance of the reciprocating seals on a larger diameter (100 mm in diameter ) axial piston is theoretically investigated.Based on the characteristics of the clearance flow between the seal and the piston, reasonable boundary conditions for Navier-Stokes equations are determined and the equations are modified, so that the final equations can describe the real flow state of the clearance flow.Through combining the final equations with finite element method, the pressure distributions within the clearance field during the reciprocating motion of the piston and the leakage rate with the pressure are studied.The deflections of the seal which affect sealing performance are calculated as well.Sealing performance of piston seals using oil as the working liquid is compared with using water.It is concluded that the seal using water as the working liquid is under dry friction, which cannot be dealt with the theory of fluid mechanics.The seal structure is only acceptable using oil as the working liquid..

  18. Investigation and Improvement of the Staggered Labyrinth Seal

    Institute of Scientific and Technical Information of China (English)

    LIN Zhirong; WANG Xudong; YUAN Xin; SHIBUKAWANaoki; NOGUCHI Taro

    2015-01-01

    Recent studies on staggered labyrinth seals have focused on the effects of different parameters, such as the pressure ratio and rotational speed on the leakage flow rate. However, few investigations pay sufficient attention to flow details and the sealing mechanism, which would be of practical importance in designing seals having higher performance. This paper establishes a theoretical model to study the seal mechanism, thus revealing that leakage is determined by the pressure ratio and geometric structure. Numerical simulation is implemented to illustrate details of the flow field within the seal structure. Viscous dissipation is used to quantitatively investigate the contribution that each location makes to the seal performance, revealing that orifices and stagnation points are the most important positions in the seal structure, generating the most dissipation. The orifice is carefully studied by using the theoretical model. Experiments for different pressure ratios are conducted and the results match well with those of the theoretical model and numerical simulation, verifying the theoretical model and analysis of the seal mechanism. Three new designs, based on a good understanding of the seal mechanism, are presented, with one reducing leakage by 24.5%.

  19. Reducing Seal Adhesion in Low Impact Docking Systems

    Science.gov (United States)

    Banks, Bruce A.; Miller, Sharon K.

    2010-01-01

    Silicone elastomers, used in seals for airlocks or other sealing surfaces in space, are sticky in their as-received condition. Because of the sticking, a greater force may be needed to separate the mating surfaces. If the adhesion is sufficiently high, a sudden unpredicted movement of the spacecraft during undocking, vibration, or uneven release could pull off the seal, resulting in a damage that would have to be repaired before another docking. The damaged seal can result in significant gas leakage and possibly in a catastrophic mishap impacting the safety of the crew. It is also possible that a compromised seal could result in a delayed but sudden gas leak that could put the crew at unexpected risk. This is especially of concern for androgynous seals, which have identical mating surfaces on both sides for interchangeability and redundancy. Such seals typically have elastomer-on-elastomer sealing surfaces. To reduce sticking, one could use release agents such as powders and lubricants, but these can be easily removed and transferred to other surfaces, causing uneven sealing and contamination. Modification of the elastomer surface to make a more slippery and less sticky surface that is integral with the bulk elastomer would be more desirable.

  20. Soft Wire Seals For High Temperatures And Pressures

    Science.gov (United States)

    Tsou, Peter

    1996-01-01

    Soft metal wires used to make O-ring and similar seals for vessels, flanges, and fittings subject to pressures equal to or greater than 1,000 psi and temperatures equal to or greater than 100 degrees C. Seals containing soft metal wires made inexpensively because fabricated to looser tolerances like those of lower-temperature, lower-pressure elastomeric-O-ring seals, which they resemble. Seals also made with noncircular grooves and with soft metals other than aluminum. For example, gold performs well, though expensive. For other applications, silver good choice.

  1. Numerical Analysis of Nonlinear Rotor-bearing-seal System

    Institute of Scientific and Technical Information of China (English)

    CHENG Mei; MENG Guang; JING Jian-ping

    2008-01-01

    The system state trajectory, Poincaré maps, largest Lyapunov exponents, frequency spectra and bifurcation diagrams were used to investigate the non-linear dynamic behaviors of a rotor-bearing-seal coupled system and to analyze the influence of the seal and bearing on the nonlinear characteristics of the rotor system. Various nonlinear phenomena in the rotor-bearing-seal system, such as periodic motion, double-periodicmotion, multi-periodic motion and quasi-periodic motion were investigated. The results may contribute to a further understanding of the non-linear dynamics of the rotor-bearing-seal coupled system.

  2. Reactor coolant pump shaft seal behavior during blackout conditions

    Energy Technology Data Exchange (ETDEWEB)

    Mings, W.J.

    1985-01-01

    The United States Nuclear Regulatory Commission has classified the problem of reactor coolant pump seal failures as an unresolved safety issue. This decision was made in large part due to experimental results obtained from a research program developed to study shaft seal performance during station blackout and reported in this paper. Testing and analysis indicated a potential for pump seal failure under postulated blackout conditions leading to a loss of primary coolant with a concomitant danger of core uncovery. The work to date has not answered all the concerns regarding shaft seal failure but it has helped scope the problem and focus future research needed to completely resolve this issue.

  3. Split ring floating air riding seal for a turbine

    Energy Technology Data Exchange (ETDEWEB)

    Mills, Jacob A

    2015-11-03

    A floating air riding seal for a gas turbine engine with a rotor and a stator, an annular piston chamber with an axial moveable annular piston assembly within the annular piston chamber, an annular cavity formed on the annular piston assembly that faces a seal surface on the rotor, and a central passage connecting the annular cavity to the annular piston chamber to supply compressed air to the seal face, where the annular piston assembly is a split piston assembly to maintain a tight seal as coning of the rotor disk occurs.

  4. Rotordynamic and leakage characteristics of a 4-stage brush seal

    Science.gov (United States)

    Conner, K. J.; Childs, D. W.

    1992-12-01

    Experimental results are presented for the direct and cross-coupled stiffness and damping coefficients as well as the leakage performance for a 4-stage brush seal. Variable test parameters include the inlet pressure, pressure ratio, shaft speed, fluid prerotation, and seal spacing. Direct damping is shown to increase with running speed; otherwise, the rotordynamic coefficients are relatively insensitive to changes in the test parameters. Cross-coupled stiffness is generally unchanged by increasing the inlet tangential velocity to the seals, suggesting that the brush seal is not affected by inlet swirl. Direct stiffness is shown to increase with frequency; however, the magnitudes of direct stiffness are always positive. Cross-coupled stiffness increases slightly with frequency; yet not as drastically as direct stiffness. Comparisons of test results for the 4-stage brush seal with an 8-cavity labyrinth showed superior rotordynamics performance for the brush seal; viz., large values for direct stiffness and lower values for the (destabilizing) cross-coupled stiffness coefficient. The damping for brush seals is smaller, but comparable to labyrinth seals. The whirl-frequency ratio is always smaller for the brush seal.

  5. Ceramic-to-metal sealing. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Gates, W.G.

    1977-03-01

    Ceramic-to-metal sealing was accomplished by brazing a metallized alumina insulator to a Kovar (Carpenter Technology Corporation) pin and header. A braze alloy wetting evaluation and a braze joint tensile strength evaluation were completed by brazing the specimens in a hydrogen atmosphere. From these evaluations the best braze alloy and brazing cycle were selected. Twelve braze alloys were evaluated and Nicusil 3 (Western Gold and Platinum Company) braze alloy was found to have good wetting characteristics and optimum strength. Assemblies brazed with this alloy were vacuum leak tight and metallurgically sound.

  6. Measure Guideline: Guide to Attic Air Sealing

    Energy Technology Data Exchange (ETDEWEB)

    Lstiburek, Joseph [Building Science Corporation, Westford, MA (United States)

    2014-09-01

    The purpose of this measure guideline is to provide information and recommendations for the preparation work necessary prior to adding attic insulation. Even though the purpose of this guide is to save energy, health, safety, and durability should not be compromised by energy efficiency. Accordingly, combustion safety and ventilation for indoor air quality are addressed first. Durability and attic ventilation then follow. Finally, to maximize energy savings, air sealing is completed prior to insulating. The guide is intended for home remodelers, builders, insulation contractors, mechanical contractors, general contractors who have previously done remodeling and homeowners as a guide to the work that needs to be done.

  7. Cadmium Toxicity to Ringed Seals (Phoca hispida)

    DEFF Research Database (Denmark)

    Sonne, Christian; Dietz, R.; Riget, F. F.;

    as laboratory mammals. We have studied possible cadmium induced histopathological changes in the kidneys as well as a demineralisation of the skeletal system (DXA-scanning of lumbal vertebraes). No obvious cadmium induced toxic changes were found. Food composition and physiological adaptations may explain......Cadmium concentrations in kidneys from ringed seals (Phoca hispida) from North West Greenland (Qaanaaq) are high. Concentrations range at level known to induce renal toxic effects (mainly tubulopathy) and demineralisation (osteopenia) of the skeletal system (Fanconi's Syndrome) in humans as well...

  8. Compatibility testing of vacuum seal materials

    Science.gov (United States)

    Foster, P. A.; Rodin, W. A.

    1993-05-01

    Small scale materials compatibility testing was conducted for three elastomers considered for use as vacuum seal materials: Adiprene MOCA-cured; Adiprene Cyanacured; and Sylgard silastic rubber. The tests were conducted using orthogonal array designed experiments for each of the elastomers placed in contact with three materials commonly used during weapon disassembly operations: Duxseal, Sylgard 186 grease, and 2-propyl alcohol. The test results indicated that only the 2-propyl alcohol had a significant effect on the elastomer hardness and physical properties. The alcohol had the largest effect on the two Adiprene materials, and the silastic rubber was the least affected.

  9. Remote video registration of seals at Rødsand seal sanctuary

    DEFF Research Database (Denmark)

    Edren, Susi M.C.; Teilmann, J.; Dietz, R.

    This report describes the preliminary use of a remote-controlled webbased camera system in the Rødsand seal sanctuary. The camera system powered by solar and wind energy is designed to operate under extreme weather conditions. Live images and still photos are transmitted to a land station, from...

  10. Nanoparticle Reactions on Chip

    Science.gov (United States)

    Köhler, J. M.; Kirner, Th.; Wagner, J.; Csáki, A.; Möller, R.; Fritzsche, W.

    The handling of heterogenous systems in micro reactors is difficult due to their adhesion and transport behaviour. Therefore, the formation of precipitates and gas bubbles has to be avoided in micro reaction technology, in most cases. But, micro channels and other micro reactors offer interesting possibilities for the control of reaction conditions and transport by diffusion and convection due to the laminar flow caused by small Reynolds numbers. This can be used for the preparation and modification of objects, which are much smaller than the cross section of microchannels. The formation of colloidal solutions and the change of surface states of nano particles are two important tasks for the application of chip reactors in nanoparticle technology. Some concepts for the preparation and reaction of nanoparticles in modular chip reactor arrangements will be discussed.

  11. Three-step cylindrical seal for high-performance turbomachines

    Science.gov (United States)

    Hendricks, Robert C.

    1987-01-01

    A three-step cylindrical seal configuration representing the seal for a high performance turbopump (e.g., the space shuttle main engine fuel pump) was tested under static (nonrotating) conditions. The test data included critical mass flux and pressure profiles over a wide range of inlet temperatures and pressures for fluid nitrogen and fluid hydrogen with the seal in concentric and fully eccentric positions. The critical mass flux (leakage rate) was 70% that of an equivalent straight cylindrical seal with a correspondingly higher pressure drop based on the same flow areas of 0.3569 sq cm but 85% that of the straight seal based on the third-step flow area of 0.3044 sq cm. The mass flow rates for the three step cylindrical seal in the fully eccentric and concentric positions were essentially the same, and the trends in flow coefficient followed those of a simple axisymmetric inlet configuration. However, for inlet stagnation temperatures less than the thermodynamic critical temperature the pressure profiles exhibited a flat region throughout the third step of the seal, with the pressure magnitude dependent on the inlet stagnation temperature. Such profiles represent an extreme positive direct stiffness. These conditions engendered a crossover in the pressure profile upstream of the postulated choke that resulted in a local negative stiffness. Flat and crossover profiles resulting from choking within the seal are practically unknown to the seal designer. However, they are of critical importance to turbomachine stability and must be integrated into any dynamic analysis of a seal of this configuration. In addition, choking is highly dependent on geometry, inlet-to-backpressure ratio, and inlet temperature and can occur within the seal even though the backpressure is above the critical pressure.

  12. Analysis of physical demands during bulk bag closing and sealing.

    Science.gov (United States)

    Nasarwanji, Mahiyar F; Reardon, Leanna M; Heberger, John R; Dempsey, Patrick G

    2016-05-01

    Several tools are sold and recommended for closing and sealing flexible intermediate bulk containers (bulk bags) which are used to transport product that has been mined and processed. However, there is limited information on the risks, physical demands, or the benefits of using one tool over another. The purpose of this study was to evaluate the physical demands involved with two closing methods and several sealing tools in order to provide recommendations for selecting tools to reduce exposure to risk factors for work-related musculoskeletal disorders. In this study, twelve participants completed bag closing and sealing tasks using two different closing methods and eight sealing tools on two types of bulk bags. Physical demands and performance were evaluated using muscle activity, perceived exertion, subjective ratings of use, and time. Results indicate that using the "flowering" method to close bags required on average 32% less muscle activity, 30% less perceived exertion, 42% less time, and was preferred by participants compared to using the "snaking" method. For sealing, there was no single method significantly better across all measures; however, using a pneumatic cable tie gun consistently had the lowest muscle activity and perceived exertion ratings. The pneumatic cable tie gun did require approximately 33% more time to seal the bag compared to methods without a tool, but the amount of time to seal the bag was comparable to using other tools. Further, sealing a spout bulk bag required on average 13% less muscle activity, 18% less perceived exertion, 35% less time, and was preferred by participants compared to sealing a duffle bulk bag. The current results suggest that closing the spout bag using the flowering method and sealing the bag using the pneumatic cable tie gun that is installed with a tool balancer is ergonomically advantageous. Our findings can help organizations select methods and tools that pose the lowest physical demands when closing and

  13. Sealed joint structure for electrochemical device

    Science.gov (United States)

    Tucker, Michael C; Jacobson, Craig P; De Jonghe, Lutgard C; Visco, Steven J

    2013-05-21

    Several members make up a joint in a high-temperature electrochemical device, wherein the various members perform different functions. The joint is useful for joining multiple cells (generally tubular modules) of an electrochemical device to produce a multi-cell segment-in-series stack for a solid oxide fuel cell, for instance. The joint includes sections that bond the joining members to each other; one or more seal sections that provide gas-tightness, and sections providing electrical connection and/or electrical insulation between the various joining members. A suitable joint configuration for an electrochemical device has a metal joint housing, a first porous electrode, a second porous electrode, separated from the first porous electrode by a solid electrolyte, and an insulating member disposed between the metal joint housing and the electrolyte and second electrode. One or more brazes structurally and electrically connects the first electrode to the metal joint housing and forms a gas tight seal between the first electrode and the second electrode.

  14. Brush seal shaft wear resistant coatings

    Science.gov (United States)

    Howe, Harold

    1995-03-01

    Brush seals suffer from high wear, which reduces their effectiveness. This work sought to reduce brush seal wear by identifying and testing several industry standard coatings. One of the coatings was developed for this work. It was a co-sprayed PSZ with boron-nitride added for a high temperature dry lubricant. Other coatings tested were a PSZ, chrome carbide and a bare rotor. Testing of these coatings included thermal shocking, tensile testing and wear/coefficient of friction testing. Wear testing consisted of applying a coating to a rotor and then running a sample tuft of SiC ceramic fiber against the coating. Surface speeds at point of contact were slightly over 1000 ft/sec. Rotor wear was noted, as well as coefficient of friction data. Results from the testing indicates that the oxide ceramic coatings cannot withstand the given set of conditions. Carbide coatings will not work because of the need for a metallic binder, which oxidizes in the high heat produced by friction. All work indicated a need for a coating that has a lubricant contained within itself and the coating must be resistant to an oxidizing environment.

  15. Evaluation of Polymer Hermetically Sealed Tantalum Capacitors

    Science.gov (United States)

    Teverovsky, Alexander A.

    2014-01-01

    Polymer cathode tantalum capacitors have lower ESR (equivalent series resistance) compared to other types of tantalum capacitors and for this reason have gained popularity in the electronics design community. Their use allows improved performance of power supply systems along with substantial reduction of size and weight of the components used. However, these parts have poor thermal stability and can degrade in humid environments. Polymer hermetically sealed (PHS) capacitors avoid problems related to environmental degradation of molded case parts and can potentially replace current wet and solid hermetically sealed capacitors. In this work, PHS capacitors manufactured per DLA LAM DWG#13030 are evaluated for space applications. Several lots of capacitors manufactured over period from 2010 to 2014 were tested for the consistency of performance, electrical and thermal characteristics, highly accelerated life testing, and robustness under reverse bias and random vibration conditions. Special attention was given to analysis of leakage currents and the effect of long-term high temperature storage on capacitors in as is condition and after hermeticity loss. The results show that PHS capacitors might be especially effective for low-temperature applications or for system requiring a cold start-up. Additional screening and qualification testing have been recommended to assure the necessary quality of capacitors for space projects.

  16. Rapid recovery of Dutch gray seal colonies fueled by immigration

    NARCIS (Netherlands)

    Brasseur, S.M.J.M.; Polanen Petel, van T.; Gerrodette, T.; Meesters, E.; Reijnders, P.J.H.; Aarts, G.M.

    2015-01-01

    Gray seals were first observed breeding in the Dutch Wadden Sea in 1985, after centuries of absence. The breeding colony there is now the largest on the European continent. We describe the changes in gray seal numbers and their geographical expansion, and estimate how these processes were influenced

  17. Analog Video Authentication and Seal Verification Equipment Development

    Energy Technology Data Exchange (ETDEWEB)

    Gregory Lancaster

    2012-09-01

    Under contract to the US Department of Energy in support of arms control treaty verification activities, the Savannah River National Laboratory in conjunction with the Pacific Northwest National Laboratory, the Idaho National Laboratory and Milagro Consulting, LLC developed equipment for use within a chain of custody regime. This paper discussed two specific devices, the Authentication Through the Lens (ATL) analog video authentication system and a photographic multi-seal reader. Both of these devices have been demonstrated in a field trial, and the experience gained throughout will also be discussed. Typically, cryptographic methods are used to prove the authenticity of digital images and video used in arms control chain of custody applications. However, in some applications analog cameras are used. Since cryptographic authentication methods will not work on analog video streams, a simple method of authenticating analog video was developed and tested. A photographic multi-seal reader was developed to image different types of visual unique identifiers for use in chain of custody and authentication activities. This seal reader is unique in its ability to image various types of seals including the Cobra Seal, Reflective Particle Tags, and adhesive seals. Flicker comparison is used to compare before and after images collected with the seal reader in order to detect tampering and verify the integrity of the seal.

  18. 27 CFR 72.68 - Sale on sealed, competitive bids.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Sale on sealed, competitive bids. 72.68 Section 72.68 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE... PROPERTY Administrative Sale or Disposition of Personal Property § 72.68 Sale on sealed, competitive...

  19. Unification of reactor elastomeric sealing based on material

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, N.K., E-mail: nksinha@igcar.gov.in [Indira Gandhi Centre for Atomic Research (IGCAR), Department of Atomic Energy (DAE), Kalpakkam, Tamilnadu 603102 (India); Raj, Baldev [Indira Gandhi Centre for Atomic Research (IGCAR), Department of Atomic Energy (DAE), Kalpakkam, Tamilnadu 603102 (India)

    2012-02-15

    The unification of elastomeric sealing applications of Indian nuclear reactors based on a few qualified fluoroelastomer/perfluoroelastomer compounds and standardized approaches for finite element analysis (FEA) based design, manufacturing process and antifriction coatings is discussed. It is shown that the advance polymer architecture based Viton{sup Registered-Sign} formulation developed for inflatable seals of 500 MWe Prototype Fast Breeder Reactor (PFBR) and its four basic variations can encompass other sealing applications of PFBR with minimum additional efforts on development and validation. Changing the blend ratio of Viton{sup Registered-Sign} GBL 200S and 600S in inflatable seal formulation could extend its use to Pressurized Heavy Water Reactors (PHWRs). The higher operating temperature of Advanced Heavy Water Reactor (AHWR) seals expands the choice to perfluoroelastomers. FEA based on plane-strain/axisymmetric modeling (with Mooney-Rivlin as the basic constitutive model), seal manufacture by cold feed extrusion and injection molding as well as plasma Teflon-like coating belonging to two variations obtained from the development of inflatable seals provide the necessary standardization for unification. The gains in simplification of design, development and operation of seals along with the enhancements of safety and reliability are expected to be substantial.

  20. Stirling engine or heat pump having an improved seal

    Science.gov (United States)

    White, Maurice A.; Riggle, Peter; Emigh, Stuart G.

    1985-01-01

    A Stirling Engine or Heat Pump having two relatively movable machine elements for power transmission purposes includes a hermetic seal bellows interposed between the elements for separating a working gas from a pressure compensating liquid that balances pressure across the bellows to reduce bellows stress and to assure long bellows life. The volume of pressure compensating liquid displaced due to relative movement between the machine elements is minimized by enclosing the compensating liquid within a region exposed to portions of both machine elements at one axial end of a slidable interface presented between them by a clearance seal having an effective diameter of the seal bellows. Pressure equalization across the bellows is achieved by a separate hermetically sealed compensator including a movable enclosed bellows. The interior of the compensator bellows is in communication with one side of the seal bellows, and its exterior is in communication with the remaining side of the seal bellows. A buffer gas or additional liquid region can be provided at the remaining axial end of the clearnace seal, along with valved arrangements for makeup of liquid leakage through the clearance seal.

  1. Mercury and selenium in wild and experimental seals

    NARCIS (Netherlands)

    Ven, van de W.S.M.; Koeman, J.H.; Svenson, A.

    1979-01-01

    This paper describes the tissue distribution of inorganic mercury, organic mercury selenium in Dutch and British seals as well as in seals which were dosed with methylmercury under experimental conditions. In the experimental animals, a time-related increase of both mercury and selenium was found in

  2. Plastic ingestion by harbour seal (Phoca vitulina) in the Netherlands

    NARCIS (Netherlands)

    Bravo Rebolledo, E.; Franeker, van J.A.; Jansen, O.E.; Brasseur, S.M.J.M.

    2013-01-01

    Abundance of ingested debris by seals has been mentioned as a potential indicator of marine litter in the European Marine Strategy Framework Directive (MSFD). A sample of 107 stomachs, 100 intestines and 125 scats of harbour seals from the Netherlands was analysed for the presence of plastics. Incid

  3. Building America Top Innovations 2012: Attic Air Sealing Guidelines

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2013-01-01

    This Building America Top Innovations profile describes the DOE-sponsored Guide to Attic Air Sealing by Building America research partner Building Science Corporation, which provides best practices for attic air sealing. The guide has had 21,000 views and 13,000 downloads since it was posted.

  4. Sealing occlusal caries lesions in adults referred for restorative treatment

    DEFF Research Database (Denmark)

    Bakhshandeh, Azam; Qvist, Vibeke; Ekstrand, Kim R

    2012-01-01

    treatment by senior lecturers at School of Dentistry, Copenhagen, Denmark were included. In case the patient had more than one occlusal caries lesion, randomization between sealing and restoration was made; otherwise, the lesion was sealed. In total, 60 resin sealants and 12 composite restorations were made...

  5. Modelling prey consumption and switching by UK grey seals

    DEFF Research Database (Denmark)

    Smout, Sophie; Rindorf, Anna; Hammond, Philip S.

    2014-01-01

    Grey seals (Halichoerus grypus) are adaptable generalist predatorswhose diet includes commercial fish species such as cod. Consumption by the seals may reduce the size of some fish stocks or have an adverse effect on stock recovery programmes, especially because predation may trap sparse prey pop...

  6. Vacuum Packaging of MEMS With Multiple Internal Seal Rings

    Science.gov (United States)

    Hayworth, Ken; Yee, Karl; Shcheglov, Kirill; Bae, Youngsam; Wiberg, Dean; Peay, Chris; Challoner, Anthony

    2008-01-01

    A proposed method of design and fabrication of vacuum-packaged microelectromechanical systems (MEMS) and of individual microelectromechanical devices involves the use of multiple internal seal rings (MISRs) in conjunction with vias (through holes plated with metal for electrical contacts). The proposed method is compatible with mass production in a wafer-level fabrication process, in which the dozens of MEMS or individual microelectromechanical devices on a typical wafer are simultaneously vacuum packaged by bonding a capping wafer before the devices are singulated (cut apart by use of a dicing saw). In addition to being compatible with mass production, the proposed method would eliminate the need for some complex and expensive production steps and would yield more reliable vacuum seals. Conventionally, each MEMS or individual microelectromechanical device is fabricated as one of many identical units on a device wafer. Vacuum packaging is accomplished by bonding the device wafer to a capping wafer with metal seal rings (one ring surrounding each unit) that have been formed on the capping wafer. The electrical leads of each unit are laid out on what would otherwise be a flat surface of the device wafer, against which the seal ring is to be pressed for sealing. The resulting pattern of metal lines and their insulating oxide coverings presents a very rough and uneven surface, upon which it is difficult to pattern the sealing metal. Consequently, the seal is prone to leakage unless additional costly and complex planarization steps are performed before patterning the seal ring and bonding the wafers.

  7. 77 FR 73263 - Organization and Functions, and Seal

    Science.gov (United States)

    2012-12-10

    ... Federal Housing Enterprise Oversight 12 CFR Part 1700 RIN 2590-AA54 Organization and Functions, and Seal... Federal home loan banks, Organization and functions (Government agencies). 12 CFR Part 1200 Organization and functions (Government agencies), Seals and insignia. 12 CFR Part 1700 Organization and...

  8. 46 CFR 59.10-30 - Seal welding.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Seal welding. 59.10-30 Section 59.10-30 Shipping COAST... VESSELS AND APPURTENANCES Welding Repairs to Boilers and Pressure Vessels in -Service § 59.10-30 Seal welding. Where leaks occur in riveted joints or connections, they shall be carefully investigated...

  9. Laboratory Testing of Aerosol for Enclosure Air Sealing

    Energy Technology Data Exchange (ETDEWEB)

    Harrington, Curtis [Building Industry Research Alliance (BIRA), Stockton, CA (United States); Modera, Mark [Building Industry Research Alliance (BIRA), Stockton, CA (United States)

    2012-05-01

    This report presents a process for improving the air tightness of a building envelope by sealing shell leaks with an aerosol sealing technology. Both retrofit and new construction applications are possible through applying this process either in attics and crawlspaces or during rough-in stage.

  10. Dry compliant seal for phosphoric acid fuel cell

    Science.gov (United States)

    Granata, Jr., Samuel J. (Inventor); Woodle, Boyd M. (Inventor)

    1990-01-01

    A dry compliant overlapping seal for a phosphoric acid fuel cell preformed f non-compliant Teflon to make an anode seal frame that encircles an anode assembly, a cathode seal frame that encircles a cathode assembly and a compliant seal frame made of expanded Teflon, generally encircling a matrix assembly. Each frame has a thickness selected to accommodate various tolerances of the fuel cell elements and are either bonded to one of the other frames or to a bipolar or end plate. One of the non-compliant frames is wider than the other frames forming an overlap of the matrix over the wider seal frame, which cooperates with electrolyte permeating the matrix to form a wet seal within the fuel cell that prevents process gases from intermixing at the periphery of the fuel cell and a dry seal surrounding the cell to keep electrolyte from the periphery thereof. The frames may be made in one piece, in L-shaped portions or in strips and have an outer perimeter which registers with the outer perimeter of bipolar or end plates to form surfaces upon which flanges of pan shaped, gas manifolds can be sealed.

  11. Brush Seal Arrangement for the RS-68 Turbopump Set

    Science.gov (United States)

    Nunez, D.; Ransom, D.; Prueger, G.

    2006-01-01

    The nature of the RS-68 turbopumps requires that the hydrogen seals separating the pump from the turbine must have extremely low levels of leakage and be contained in small packages. Conventional seal technologies are not able to reasonably satisfy such design requirements. A review of experimental measurements and analysis publications suggests that brush seals are well suited for the design requirements. Brush seals are shown to have less leakage than conventional labyrinth and damper seals and have no adverse effects on the rotordynamics of the machine. The bulk-flow analysis presented by Hendricks et al. is used as a guideline to create a spreadsheet that provides mass flow through the seal and heat generated by the rubbing contact of the bristles on the shaft. The analysis is anchored to published data for LN2 and LH2 leakage tests. Finally, the analysis is used to design seals for both applications. It is observed that the most important analysis parameter is the thickness of the bristle pack and its relationship to seal clearance, lay angle and pressure drop.

  12. Seal with integrated shroud for androgenous docking and berthing in contaminated environments

    Science.gov (United States)

    Daniels, Christopher C. (Inventor)

    2012-01-01

    The present invention is directed to a specially configured seal system which provides a barrier to gas leakage flow between a pressurized module and its external environment. The seal includes a shroud covering which protects the sealing interface from its environment when not in use, and retracts to expose the sealing interface when mated. The seal system is constructed and arranged to mate with a seal of identical construction and arrangement or to mate with a flat surface.

  13. Performance assessment of sealing systems. Conceptual and integrated modelling of plugs and seals

    Energy Technology Data Exchange (ETDEWEB)

    Ruebel, Andre; Buhmann, Dieter; Kindlein, Jonathan; Lauke, Thomas

    2016-08-15

    The long-time isolation of radionuclides from the biosphere is the goal of the storage of radioactive waste in deep geological repositories. For repositories in rock salt, this goal is achieved on the one hand by the impermeable undisturbed part of the salt host rock formation and on the other hand by crushed salt, which is used to backfill the mine openings in the emplacement areas and galleries created during the construction of the repository. The crushed salt backfill is compacted over time and achieves a sufficiently high hydraulic resistance to avoid inflow of brines into the emplacement areas of the repository in the long-term. Plugs and seals must additionally provide their sealing function during the early post closure phase, until the compaction of the backfill is adequate and the permeability of the backfill is sufficiently low. To assess the future development of the waste repository, an adequate knowledge of the material behaviour is necessary and related mathematical models must be developed to be able to perform predictions on the long-term safety of the repository. An integrated performance assessment model was formulated that describes the long-term behaviour of a sealing built from salt concrete. The average permeability of the sealing changes with time after its emplacement from various processes of which two were regarded in a constitutive model: first, the healing of the EDZ in the host rock around the sealing, and second, the corrosion of the salt concrete material resulting from brine attack. Empirical parameter model functions were defined for both processes to reflect the actual behaviour. The mathematical model was implemented in the integrated performance assessment model LOPOS which is used by GRS as near-field model for repositories in salt. Deterministic and probabilistic calculations were performed with realistic parameters showing how the permeability of the sealing decreases during the first 2 000 years due to the healing of the EDZ

  14. Ultra-thin chip technology and applications

    CERN Document Server

    2010-01-01

    Ultra-thin chips are the "smart skin" of a conventional silicon chip. This book shows how very thin and flexible chips can be fabricated and used in many new applications in microelectronics, microsystems, biomedical and other fields. It provides a comprehensive reference to the fabrication technology, post processing, characterization and the applications of ultra-thin chips.

  15. Towards Dependable Network-on-Chip Architectures

    NARCIS (Netherlands)

    Chen, C.

    2015-01-01

    The aggressive semiconductor technology scaling provides the means for doubling the amount of transistors on a single chip each and every 18 months. To efficiently utilize these vast chip resources, Multi-Processor Systems on Chip (MPSoCs) integrated with a Network-on-Chip (NoC) communication infras

  16. Application of hydrophilic magnetic fluid to oil seal

    Science.gov (United States)

    Kim, Y. S.; Nakatsuka, K.; Fujita, T.; Atarashi, T.

    1999-07-01

    Bearing and gear are important components in machines. Lubricant for bearing or gear is usually confined in working space by rubber retainer or mechanical seal, and its lifetime which is determined by the friction wear of sealing material is important. In this report, the basic characteristics of magnetic fluid seal applied to lubricant retainer is studied. The fluid used for this purpose is ethyleneglycol-based magnetic fluid in which silica-coated iron particles are dispersed. The lubricant oil seal set consisting of six stages of pole piece and Nd-permanent magnets (4.0 Wb/m 2) in seal housing showed an excellent pressure resistance of 618 kPa under a rotating speed of 1800 rpm.

  17. Grey seal predation on forage fish in the Baltic Sea

    DEFF Research Database (Denmark)

    Eero, Aro; Neuenfeldt, Stefan; Aho, Teija;

    has increased accordingly. The diet of grey seal in the Baltic consists of ca. 20 fish species. The most abundant prey items in the Baltic proper are Baltic herring, sprat, and cod, and in the Bothnian Sea and Bothnian Bay Baltic herring, Coregonus sp., Baltic salmon, and sea trout. An adult seal...... consumes on average round 4.5 kg fish per day, of which 55% are clupeoids in the Baltic Main basin and 70% in the Bothnian Sea and Bothnian Bay. According to acoustic estimates, predator– prey distribution patterns, migration patterns, and multispecies analysis (SMS), the predation effect of grey seals...... on Baltic herring and sprat stocks is still at a very low level. Hence, with present grey seal stock sizes, the impact of seal predation can be ignored in whole Baltic‐scale herring and sprat stock management considerations. Locally, however, grey seal–fishery interactions play an important role and should...

  18. Asphalt emulsion sealing of uranium mill tailings. 1980 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, J.N.; Koehmstedt, P.L; Esterl, D.J.; Freeman, H.D.; Buelt, J.L.; Nelson, D.A.; Elmore, M.R.

    1981-05-01

    Studies of asphalt emulsion sealants conducted by the Pacific Northwest Laboratory have demonstrated that the sealants are effective in containing radon and other potentially hazardous material within uranium tailings. The laboratory and field studies have further demonstrated that radon exhalation from uranium tailings piles can be reduced by greater than 99% to near background levels. Field tests at the tailings pile in Grand Junction, Colorado, confirmed that an 8-cm admix seal containing 22 wt% asphalt could be effectively applied with a cold-mix paver. Other techniques were successfully tested, including a soil stabilizer and a hot, rubberized asphalt seal that was applied with a distributor truck. After the seals were applied and compacted, overburden was applied over the seal to protect the seal from ultraviolet degradation.

  19. Mathematical model of the Beta Rand Cam{trademark} engine vane seals

    Energy Technology Data Exchange (ETDEWEB)

    Braden, C.H.; Thompson, G.J.; Smith, J.E.; Mucino, V.H. [West Virginia Univ., Morgantown, WV (United States)

    1996-12-31

    A mathematical model of the vane sealing mechanism is presented to determine how the loading on the seals will affect the performance of the Rand Cam{trademark} engine. Within the Rand Cam{trademark} engine, sacrificial linear seals in the vane are used as the main sealing mechanism to prevent blowby from one chamber to the next. Throughout this investigation a kinetostatic analysis, based upon Yamamoto`s Wankel apex seal analysis, is extended into three dimensions. The input data to the model can be varied to study the effects of seal dimensions, seal material, seal dynamics, and friction.

  20. Experimental and Simulation Studies on Cold Welding Sealing Process of Heat Pipes

    Science.gov (United States)

    Li, Yong; Chen, Shengle; Huang, Jinlong; Yan, Yuying; Zeng, Zhixin

    2017-03-01

    Sealing quality strongly affects heat pipe performance, but few studies focus on the process of heat pipe sealing. Cold welding sealing technology based on a stamping process is applied for heat pipe sealing. The bonding mechanism of the cold welding sealing process (CWSP) is investigated and compared with the experimental results obtained from the bonding interface analysis. An orthogonal experiment is conducted to observe the effects of various parameters, including the sealing gap, sealing length, sealing diameter, and sealing velocity on bonding strength. A method with the utilization of saturated vapor pressure inside a copper tube is proposed to evaluate bonding strength. A corresponding finite element model is developed to investigate the effects of sealing gap and sealing velocity on plastic deformation during the cold welding process. Effects of various parameters on the bonding strength are determined and it is found that the sealing gap is the most critical factor and that the sealing velocity contributes the least effect. The best parameter combination (A 1 B 3 C 1 D 3, with a 0.5 mm sealing gap, 6 mm sealing length, 3.8 mm sealing diameter, and 50 mm/s sealing velocity) is derived within the experimental parameters. Plastic deformation results derived from the finite element model are consistent with those from the experiment. The instruction for the CWSP of heat pipes and the design of sealing dies of heat pipes are provided.

  1. Repairable chip bonding/interconnect process

    Science.gov (United States)

    Bernhardt, Anthony F.; Contolini, Robert J.; Malba, Vincent; Riddle, Robert A.

    1997-01-01

    A repairable, chip-to-board interconnect process which addresses cost and testability issues in the multi-chip modules. This process can be carried out using a chip-on-sacrificial-substrate technique, involving laser processing. This process avoids the curing/solvent evolution problems encountered in prior approaches, as well is resolving prior plating problems and the requirements for fillets. For repairable high speed chip-to-board connection, transmission lines can be formed on the sides of the chip from chip bond pads, ending in a gull wing at the bottom of the chip for subsequent solder.

  2. Interaction between Monk Seals, Monachus monachus (Hermann, 1779), and artisanal fisheries in the Foca Pilot Monk Seal conservation area, Turkey

    NARCIS (Netherlands)

    Guclusoy, H.

    2008-01-01

    The present study examines some aspects of the interaction between critically endangered Monk Seals Monachus monachus and artisanal fisheries in the Foc¿a Pilot Monk Seal Conservation Area, Turkey, between 1994 and 2002. One to four permanent researchers collected the data on this interaction during

  3. ENVIRONMENTAL TECHNOLOGY VERIFICATION REPORT-A AND A ENVIRONMENTAL SEALS, INC., SEAL ASSIST SYSTEM (SAS) PHASE II REPORT

    Science.gov (United States)

    The Environmental Technology Verification report discusses the technology and performance of Seal Assist System (SAS) for natural gas reciprocating compressor rod packing manufactured by A&A Environmental Seals, Inc. The SAS uses a secondary containment gland to collect natural g...

  4. Environmental contaminants in the food chain, NWS Seal Beach and Seal Beach NWR

    Energy Technology Data Exchange (ETDEWEB)

    Ohlendorf, H.M.; Byron, E.R. [CH2M Hill, Sacramento, CA (United States); Freas, K.E. [CH2M Hill, San Jose, CA (United States); Casados, E.M.; Kidwell, J.J. [Naval Facilities Engineering Command, San Diego, CA (United States). SW Division

    1994-12-31

    The authors conducted a study to determine whether environmental contaminants occurred in fish and invertebrates at concentrations that could be harmful to birds feeding in the estuarine salt marsh at Seal Beach National Wildlife Refuge (NWR), which is part of Naval Weapons Station (NWS) Seal Beach. Management of the refuge is focused primarily on endangered species, especially the light-footed clapper rail and the California least tern. Important food-chain organisms taken by rails (e.g., crabs and snails) and least terns (small fish) were sampled and analyzed for inorganic and organic contaminants that might be related to Navy activities at the Station. Results indicated that those contaminants are not likely to have lethal effects on rails or terns, although some chemicals (including cadmium, chromium, copper, lead, zinc and DDE) occurred at elevated concentrations in portions of the marsh. Possible sublethal effects also were evaluated and will be discussed.

  5. Turbomachine Sealing and Secondary Flows. Part 1; Review of Sealing Performance, Customer, Engine Designer, and Research Issues

    Science.gov (United States)

    Hendricks, R. C.; Steinetz, B. M.; Braun, M. J.

    2004-01-01

    Although forces outside our control shape our industry, turbomachine sealing research, design, and customer agendas established in 1978 by Ludwig, Campbell, and Smith in terms of specific fuel consumption and performance remain as objectives today. Advances have been made because failures of the space shuttle main engine turbomachinery ushered in a new understanding of sealing in high-power-density systems. Further, it has been shown that changes in sealing, especially for high-pressure rotors, dramatically change the performance of the entire engine or turbomachine. Maintaining seal leakages and secondary flows within engine design specifications remains the most efficient and cost effective way to enhance performance and minimize maintenance costs. This three-part review summarizes experiences, ideas, successes, and failures by NASA and the U.S. aerospace industry in secondary flow management in advanced turbomachinery. Part 1 presents system sealing, part 2 system rotordynamics, and part 3 modeling, with some overlap of each part.

  6. Sliding seal materials for adiabatic engines

    Science.gov (United States)

    Lankford, J.

    1985-01-01

    The sliding friction coefficients and wear rates of promising carbide, oxide, and nitride materials were measured under temperature, environmental, velocity, loading conditions that are representative of the adiabatic engine environment. In order to provide guidance needed to improve materials for this application, the program stressed fundamental understanding of the mechanisms involved in friction and wear. Microhardness tests were performed on the candidate materials at elevated temperatures, and in atmospheres relevant to the piston seal application, and optical and electron microscopy were used to elucidate the micromechanisms of wear following wear testing. X-ray spectroscopy was used to evaluate interface/environment interactions which seemed to be important in the friction and wear process. Electrical effects in the friction and wear processes were explored in order to evaluate the potential usefulness of such effects in modifying the friction and wear rates in service. However, this factor was found to be of negligible significance in controlling friction and wear.

  7. Development of a versatile lab-on-a-chip enzyme assay platform for pathogen detection in CBRNE scenarios

    Science.gov (United States)

    Klemm, Richard; Schattschneider, Sebastian; Jahn, Tobias; Hlawatsch, Nadine; Julich, Sandra; Becker, Holger; Gärtner, Claudia

    2013-05-01

    The ability to integrate complete assays on a microfluidic chip helps to greatly simplify instrument requirements and allows the use of lab-on-a-chip technology in the field. A core application for such field-portable systems is the detection of pathogens in a CBRNE scenario such as permanent monitoring of airborne pathogens, e.g. in metro stations or hospitals etc. As one assay methodology for the pathogen identification, enzymatic assays were chosen. In order evaluate different detection strategies, the realized on-chip enzyme assay module has been designed as a general platform chip. In all application cases, the assays are based on immobilized probes located in microfluidic channels. Therefore a microfluidic chip was realized containing a set of three individually addressable channels, not only for detection of the sample itself also to have a set of references for a quantitative analysis. It furthermore includes two turning valves and a waste container for clear and sealed storage of potential pathogenic liquids to avoid contamination of the environment. All liquids remain in the chip and can be disposed of in proper way subsequently to the analysis. The chip design includes four inlet ports consisting of one sample port (Luer interface) and three mini Luer interfaces for fluidic support of e.g. washing buffer, substrate and enzyme solution. The sample can be applied via a special, sealable sampling vessel with integrated female Luer interface. Thereby also pre-anaytical contamination of the environment can be provided. Other reagents that are required for analysis will be stored off chip.

  8. All-polymer organic semiconductor laser chips: Parallel fabrication and encapsulation

    DEFF Research Database (Denmark)

    Vannahme, Christoph; Klinkhammer, Sönke; Christiansen, Mads Brøkner;

    2010-01-01

    Organic semiconductor lasers are of particular interest as tunable visible laser light sources. For bringing those to market encapsulation is needed to ensure practicable lifetimes. Additionally, fabrication technologies suitable for mass production must be used. We introduce all-polymer chips...... tris(8- hydroxyquinoline) aluminum (Alq3) doped with the laser dye 4-dicyanomethylene-2- methyl-6-(p-dimethylaminostyril)-4H-pyrane (DCM) are hermetically sealed by thermally bonding a polymer lid. The organic thin film is placed in a basin within the substrate and is not in direct contact to the lid...... comprising encapsulated distributed feedback organic semiconductor lasers. Several chips are fabricated in parallel by thermal nanoimprint of the feedback grating on 4? wafer scale out of poly(methyl methacrylate) (PMMA) and cyclic olefin copolymer (COC). The lasers consisting of the organic semiconductor...

  9. Sealing of investigation boreholes, Phase 4 - Final report

    Energy Technology Data Exchange (ETDEWEB)

    Pusch, Roland [Drawrite AB, Luleaa Technical University, Luleaa (Sweden); Ramqvist, Gunnar [El-Tekno AB, Figeholm (Sweden); Bockgaard, Niclas [Golder Associates, Goeteborg (Sweden); Ekman, Lennart [LE Geokonsult AB, Baelinge (Sweden)

    2011-09-15

    The report describes the outcome of Phase 4 of the project 'Sealing of investigation boreholes', which deals with 1) characterization and planning of borehole sealing, 2) performance and quality assessment, 3) sealing of large diameter holes, and 4) interaction of clay and concrete plugs. A specific goal was to find ways to characterize, plan and seal of boreholes so that their impact on the overall hydraulic performance of the repository rock can predicted and controlled. The work comprised selection of representative 'reference holes' at the Laxemar and Forsmark sites for development of a general programme for planning and simulating implementation of borehole plugging campaigns, considering also cost issues. A second aim was to define and quantify the role of seals in the reference holes for finding out how important sealing really is. A third was to test a practical way to seal large diameter boreholes and a fourth to find out how concrete matures and performs in contact with smectite clay. The study demonstrated, in conclusion, the need for developing techniques for preparing deep boreholes before lasting seals are installed in them, since poor sealing can short-circuit hydraulically important fracture zones intersected by the holes. The practically oriented sealing activities showed that the technique developed for tight sealing of large-diameter boreholes is practical and feasible. The issue of chemical stability was investigated by testing the performance and constitution of a plug consisting of CBI concrete in contact with smectite-rich seals for almost three years. This study showed that none of them underwent substantial degradation in this period of time, but chemical reactions and thereby generated changes in physical behaviour of the plug components had taken place, particularly in the clay. The rate of degradation is, however, not yet known. It was concluded from this study that it is suitable to carry out a corresponding

  10. Carbon Dioxide Sealing Capacity: Textural or Compositional Controls?

    Energy Technology Data Exchange (ETDEWEB)

    Cranganu, Constantin; Soleymani, Hamidreza; Sadiqua, Soleymani; Watson, Kieva

    2013-11-30

    This research project is aiming to assess the carbon dioxide sealing capacity of most common seal-rocks, such as shales and non-fractured limestones, by analyzing the role of textural and compositional parameters of those rocks. We hypothesize that sealing capacity is controlled by textural and/or compositional pa-rameters of caprocks. In this research, we seek to evaluate the importance of textural and compositional parameters affecting the sealing capacity of caprocks. The conceptu-al framework involves two testable end-member hypotheses concerning the sealing ca-pacity of carbon dioxide reservoir caprocks. Better understanding of the elements controlling sealing quality will advance our knowledge regarding the sealing capacity of shales and carbonates. Due to relatively low permeability, shale and non-fractured carbonate units are considered relatively imper-meable formations which can retard reservoir fluid flow by forming high capillary pres-sure. Similarly, these unites can constitute reliable seals for carbon dioxide capture and sequestration purposes. This project is a part of the comprehensive project with the final aim of studying the caprock sealing properties and the relationship between microscopic and macroscopic characteristics of seal rocks in depleted gas fields of Oklahoma Pan-handle. Through this study we examined various seal rock characteristics to infer about their respective effects on sealing capacity in special case of replacing reservoir fluid with super critical carbon dioxide (scCO{sub 2}). To assess the effect of textural and compositional properties on scCO{sub 2} maximum reten-tion column height we collected 30 representative core samples in caprock formations in three counties (Cimarron, Texas, Beaver) in Oklahoma Panhandle. Core samples were collected from various seal formations (e.g., Cherokee, Keys, Morrowan) at different depths. We studied the compositional and textural properties of the core samples using several techniques

  11. Liquids on-chip: direct storage and release employing micro-perforated vapor barrier films.

    Science.gov (United States)

    Czurratis, Daniel; Beyl, Yvonne; Grimm, Alexander; Brettschneider, Thomas; Zinober, Sven; Lärmer, Franz; Zengerle, Roland

    2015-07-07

    Liquids on-chip describes a reagent storage concept for disposable pressure driven Lab-on-Chip (LoC) devices, which enables liquid storage in reservoirs without additional packaging. On-chip storage of liquids can be considered as one of the major challenges for the commercial break through of polymer-based LoC devices. Especially the ability for long-term storage and reagent release on demand are the most important aspects for a fully developed technology. On-chip storage not only replaces manual pipetting, it creates numerous advantages: fully automated processing, ease of use, reduction of contamination and transportation risks. Previous concepts for on-chip storage are based on liquid packaging solutions (e.g. stick packs, blisters, glass ampoules), which implicate manufacturing complexity and additional pick and place processes. That is why we prefer on-chip storage of liquids directly in reservoirs. The liquids are collected in reservoirs, which are made of high barrier polymers or coated by selected barrier layers. Therefore, commonly used polymers for LoC applications as cyclic olefin polymer (COP) and polycarbonate (PC) were investigated in the context of novel polymer composites. To ensure long-term stability the reservoirs are sealed with a commercially available barrier film by hot embossing. The barrier film is structured by pulsed laser ablation, which installs rated break points without affecting the barrier properties. A flexible membrane is actuated through pneumatic pressure for reagent release on demand. The membrane deflection breaks the barrier film and leads to efficient cleaning of the reservoirs in order to provide the liquids for further processing.

  12. Field Trial of an Aerosol-Based Enclosure Sealing Technology

    Energy Technology Data Exchange (ETDEWEB)

    Harrington, Curtis [Univ. of California, Davis, CA (United States); Springer, David [Univ. of California, Davis, CA (United States)

    2015-09-01

    This report presents the results from several demonstrations of a new method for sealing building envelope air leaks using an aerosol sealing process developed by the Western Cooling Efficiency Center at UC Davis. The process involves pressurizing a building while applying an aerosol sealant to the interior. As air escapes through leaks in the building envelope, the aerosol particles are transported to the leaks where they collect and form a seal that blocks the leak. Standard blower door technology is used to facilitate the building pressurization, which allows the installer to track the sealing progress during the installation and automatically verify the final building tightness. Each aerosol envelope sealing installation was performed after drywall was installed and taped, and the process did not appear to interrupt the construction schedule or interfere with other trades working in the homes. The labor needed to physically seal bulk air leaks in typical construction will not be replaced by this technology. However, this technology is capable of bringing the air leakage of a building that was built with standard construction techniques and HERS-verified sealing down to levels that would meet DOE Zero Energy Ready Homes program requirements. When a developer is striving to meet a tighter envelope leakage specification, this technology could greatly reduce the cost to achieve that goal by providing a simple and relatively low cost method for reducing the air leakage of a building envelope with little to no change in their common building practices.

  13. Leakage predictions for Rayleigh-step, helium-purge seals

    Science.gov (United States)

    Proctor, Margaret P.

    1988-01-01

    Rayleigh-step, helium purge, annular shaft seals, studied for use in liquid oxygen turbopumps, generate a hydrodynamic force that enables the seal to follow shaft perturbations. Hence, smaller clearances can be used to reduce seal leakage. FLOWCAL, a computer code developed by Mechanical Technology Incorporated, predicts gas flow rate through an annular seal with an axial pressure gradient. Analysis of a 50-mm Rayleigh-step, helium-purge, annular seal showed the flow rate increased axial pressure gradient, downstream pressure, and eccentricity ratio. Increased inlet temperature reduced leakage. Predictions made at maximum and minimum clearances (due to centrifugal and thermal growths, machining tolerances and + or - 2 percent uncertainty in the clearance measurement) placed wide boundaries on expected flow rates. The widest boundaries were set by thermal growth conditions. Predicted flow rates for a 50-mm Rayleigh-step, helium-purge, annular seal underestimated measured flow rates by three to seven times. However, the analysis did accurately predict flow rates for choked gas flow through annular seals when compared to flow rates measured in two other independent studies.

  14. Basis of property limits for inflatable seal fluoroelastomers

    Energy Technology Data Exchange (ETDEWEB)

    Sinha, N.K., E-mail: nksinha@igcar.gov.in [Indira Gandhi Centre for Atomic Research (IGCAR), Department of Atomic Energy (DAE), Kalpakkam, Tamilnadu 603102 (India); Raj, Baldev, E-mail: dr.baldev@psg.org.in [Indira Gandhi Centre for Atomic Research (IGCAR), Department of Atomic Energy (DAE), Kalpakkam, Tamilnadu 603102 (India)

    2012-03-15

    Identification of a set of governing physico-mechanical properties for inflatable seals of Prototype Fast Breeder Reactor (PFBR) and specification of their limits is described based on operating requirements, design practices and results from seal development. The limits of tensile strength, elongation at break, hardness, tear strength, fluid compatibility, compression set and specific gravity defined for the Viton GBL 200S/600S based inflatable seal formulation provide a standardized framework for regular production of reactor seals and a streamlined approach for compounding, design, manufacture and quality control. This assures significant reduction of efforts during the envisaged unification of Fast Breeder Reactor sealing based on four variations of inflatable seal compound which could result in a universal design code apart from significant gains in safety, reliability and life. The property set has potential use in Pressurized Heavy Water Reactor and Advanced Heavy Water Reactor. Inclusion of factors such as batch-to-batch variations of compound properties and their reproducibility during laboratory measurements, hot tensile behavior of fluoroelastomer, long term ageing effects and the margin of safety at the end of seal design life ensures the utility of property set in attaining its intended objective.

  15. Three-step labyrinth seal for high-performance turbomachines

    Science.gov (United States)

    Hendricks, Robert C.

    1987-01-01

    A three-step labyrinth seal with 12, 11, and 10 labyrinth teeth per step, respectively, was tested under static (nonrotating) conditions. The configuration represented the seal for a high-performance turbopump (e.g., the space shuttle main engine fuel pump). The test data included critical mass flux and pressure profiles over a wide range of fluid conditions at concentric, partially eccentric, and fully eccentric seal positions. The seal mass fluxes (leakage rates) were lower over the entire range of fluid conditions tested than those for data collected for similar straight and three-step cylindrical seals, and this conformed somewhat to expectations. However, the pressure profiles for the eccentric positions indicated little, if any, direct stiffness for this configuration in contrast to significant direct stiffness reported for the straight and three-step cylindrical seals over the range of test conditions. Seal dynamics depend on geometric configuration, inlet and exit parameters, fluid phase, and rotation. The method of corresponding states was applied to the mass flux data, which were found to have a pressure dependency for helium.

  16. Wafer-scale integration of sacrificial nanofluidic chips for detecting and manipulating single DNA molecules

    Science.gov (United States)

    Wang, Chao; Nam, Sung-Wook; Cotte, John M.; Jahnes, Christopher V.; Colgan, Evan G.; Bruce, Robert L.; Brink, Markus; Lofaro, Michael F.; Patel, Jyotica V.; Gignac, Lynne M.; Joseph, Eric A.; Rao, Satyavolu Papa; Stolovitzky, Gustavo; Polonsky, Stanislav; Lin, Qinghuang

    2017-01-01

    Wafer-scale fabrication of complex nanofluidic systems with integrated electronics is essential to realizing ubiquitous, compact, reliable, high-sensitivity and low-cost biomolecular sensors. Here we report a scalable fabrication strategy capable of producing nanofluidic chips with complex designs and down to single-digit nanometre dimensions over 200 mm wafer scale. Compatible with semiconductor industry standard complementary metal-oxide semiconductor logic circuit fabrication processes, this strategy extracts a patterned sacrificial silicon layer through hundreds of millions of nanoscale vent holes on each chip by gas-phase Xenon difluoride etching. Using single-molecule fluorescence imaging, we demonstrate these sacrificial nanofluidic chips can function to controllably and completely stretch lambda DNA in a two-dimensional nanofluidic network comprising channels and pillars. The flexible nanofluidic structure design, wafer-scale fabrication, single-digit nanometre channels, reliable fluidic sealing and low thermal budget make our strategy a potentially universal approach to integrating functional planar nanofluidic systems with logic circuits for lab-on-a-chip applications.

  17. Design, development, fabrication and delivery of register and multiplexer units. [CMOS monolithic chip development

    Science.gov (United States)

    Feller, A.; Lombardi, T.

    1978-01-01

    Several approaches for implementing the register and multiplexer unit into two CMOS monolithic chip types were evaluated. The CMOS standard cell array technique was selected and implemented. Using this design automation technology, two LSI CMOS arrays were designed, fabricated, packaged, and tested for proper static, functional, and dynamic operation. One of the chip types, multiplexer register type 1, is fabricated on a 0.143 x 0.123 inch chip. It uses nine standard cell types for a total of 54 standard cells. This involves more than 350 transistors and has the functional equivalent of 111 gates. The second chip, multiplexer register type 2, is housed on a 0.12 x 0.12 inch die. It uses 13 standard cell types, for a total of 42 standard cells. It contains more than 300 transistors, the functional equivalent of 112 gates. All of the hermetically sealed units were initially screened for proper functional operation. The static leakage and the dynamic leakage were measured. Dynamic measurements were made and recorded. At 10 V, 14 megabit shifting rates were measured on multiplexer register type 1. At 5 V these units shifted data at a 6.6 MHz rate. The units were designed to operate over the 3 to 15 V operating range and over a temperature range of -55 to 125 C.

  18. Experiment list: SRX122568 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ip antibody=Stat2 || treatment=LPS || time=120 min || chip antibody manufacturer 1=Abcam || chip antibody catalog... number 1=ab53149 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-839 h

  19. Experiment list: SRX122522 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ntibody=Irf2 || treatment=LPS || time=60 min || chip antibody manufacturer 1=Abcam || chip antibody catalog ...number 1=ab65048 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-498 http://

  20. Experiment list: SRX122566 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available antibody=Stat2 || treatment=LPS || time=0 min || chip antibody manufacturer 1=Abcam || chip antibody catalog... number 1=ab53149 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-839 http:/

  1. Experiment list: SRX122412 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available antibody=Junb || treatment=LPS || time=120 min || chip antibody manufacturer 1=Abcam || chip antibody catalo...g number 1=ab28838 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-46 http:/

  2. Experiment list: SRX122406 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available antibody=Irf1 || treatment=LPS || time=0 min || chip antibody manufacturer 1=Abcam || chip antibody catalog... number 1=ab52520 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-640 http:/

  3. Experiment list: SRX214070 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available =Undifferentiated || treatment=Overexpress Sox2-V5 tagged || cell line=KH2 || chip antibody 1=none || chip antibody manufacture...r 1=none || chip antibody 2=V5 || chip antibody manufacturer 2

  4. Experiment list: SRX214086 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available entiated || cell line=KH2 || chip antibody 1=none || chip antibody manufacturer 1=none || chip antibody 2=none || chip antibody manuf...acturer 2=none http://dbarchive.biosciencedbc.jp/kyushu-

  5. Experiment list: SRX122417 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ntibody=Junb || treatment=LPS || time=60 min || chip antibody manufacturer 1=Abcam || chip antibody catalog ...number 1=ab28838 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-46 http://d

  6. Experiment list: SRX122415 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ntibody=Junb || treatment=LPS || time=30 min || chip antibody manufacturer 1=Abcam || chip antibody catalog ...number 1=ab28838 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-46 http://d

  7. Experiment list: SRX122485 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available antibody=Atf3 || treatment=LPS || time=120 min || chip antibody manufacturer 1=Santa Cruz || chip antibody ...catalog number 1=sc-188 || chip antibody manufacturer 2=Abcam || chip antibody catalog number 2=ab70005-100

  8. Experiment list: SRX122565 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available antibody=Stat2 || treatment=LPS || time=0 min || chip antibody manufacturer 1=Abcam || chip antibody catalog... number 1=ab53149 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-839 http:/

  9. Experiment list: SRX122520 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ntibody=Irf2 || treatment=LPS || time=30 min || chip antibody manufacturer 1=Abcam || chip antibody catalog ...number 1=ab65048 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-498 http://

  10. Experiment list: SRX122414 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ntibody=Junb || treatment=LPS || time=30 min || chip antibody manufacturer 1=Abcam || chip antibody catalog ...number 1=ab28838 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-46 http://d

  11. Experiment list: SRX122416 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ntibody=Junb || treatment=LPS || time=60 min || chip antibody manufacturer 1=Abcam || chip antibody catalog ...number 1=ab28838 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-46 http://d

  12. Experiment list: SRX214074 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ge=Undifferentiated || treatment=Overexpress Sox17EK-V5 tagged || cell line=KH2 || chip antibody 1=none || chip antibody manufacture...r 1=none || chip antibody 2=V5 || chip antibody manufacture

  13. Experiment list: SRX214072 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available e=Undifferentiated || treatment=Overexpress Sox2KE-V5 tagged || cell line=KH2 || chip antibody 1=none || chip antibody manufacture...r 1=none || chip antibody 2=V5 || chip antibody manufacture

  14. Experiment list: SRX122523 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ntibody=Irf2 || treatment=LPS || time=60 min || chip antibody manufacturer 1=Abcam || chip antibody catalog ...number 1=ab65048 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-498 http://

  15. Experiment list: SRX214071 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available Undifferentiated || treatment=Overexpress Sox2-V5 tagged || cell line=KH2 || chip antibody 1=none || chip antibody manufacture...r 1=none || chip antibody 2=V5 || chip antibody manufacturer 2=

  16. Experiment list: SRX214073 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ge=Undifferentiated || treatment=Overexpress Sox2KE-V5 tagged || cell line=KH2 || chip antibody 1=none || chip antibody manufacture...r 1=none || chip antibody 2=V5 || chip antibody manufacture

  17. Experiment list: SRX122521 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ntibody=Irf2 || treatment=LPS || time=30 min || chip antibody manufacturer 1=Abcam || chip antibody catalog ...number 1=ab65048 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-498 http://

  18. Experiment list: SRX214075 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available age=Undifferentiated || treatment=Overexpress Sox17EK-V5 tagged || cell line=KH2 || chip antibody 1=none || chip antibody manufacture...r 1=none || chip antibody 2=V5 || chip antibody manufacture

  19. Experiment list: SRX214067 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available fferentiated || cell line=F9 || chip antibody 1=Pou5f1/Oct4 || chip antibody manufacture...r 1=Santa Cruz || chip antibody 2=none || chip antibody manufacturer 2=none http://dbarchive.bioscien

  20. Experiment list: SRX122413 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available antibody=Junb || treatment=LPS || time=120 min || chip antibody manufacturer 1=Abcam || chip antibody catalo...g number 1=ab28838 || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2=sc-46 http:/

  1. The ringed seal (Phoca hispida in the western Russian Arctic

    Directory of Open Access Journals (Sweden)

    Stanislav E Belikov

    1998-06-01

    Full Text Available This paper presents a review of available published and unpublished material on the ringed seal (Phoca hispida in the western part of the Russian Arctic, including the White, Barents and Kara seas. The purpose of the review is to discuss the status of ringed seal stocks in relation to their primary habitat, the history of sealing, and a recent harvest of the species in the region. The known primary breeding habitats for this species are in the White Sea, the south-western part of the Barents Sea, and in the coastal waters of the Kara Sea, which are seasonally covered by shore-fast ice. The main sealing sites are situated in the same areas. Female ringed seals become mature by the age of 6, and males by the age of 7. In March-April a female gives birth to one pup in a breeding lair constructed in the shore-fast ice. The most important prey species for ringed seals in the western sector of the Russian Arctic are pelagic fish and crustaceans. The maximum annual sealing level for the region was registered in the first 70 years of the 20th century: the White Sea maximum (8,912 animals was registered in 1912; the Barents Sea maximum (13,517 animals was registered in 1962; the Kara Sea maximum (13,200 animals was registered in 1933. Since the 1970s, the number of seals harvested has decreased considerably. There are no data available for the number of seals harvested annually by local residents for their subsistence.

  2. Design and development of seal components fatigue tester

    Directory of Open Access Journals (Sweden)

    P. Czop

    2008-09-01

    Full Text Available Purpose: The aim of the paper is research and development concerning a fatigue tester of shock absorber seal systems.Design/methodology/approach: Analytical approach has been applied to get an understanding of a heat exchange process. The mathematical model has been formulated and validated based on the available measurements. Numerical simulation has been carried out to illustrate a heat exchange process performance.Findings: It is possible to control a seal temperature and mechanical friction related to the rod movement into the seal at the specified velocity. The model accuracy is sufficient to perform sensitivity analysis and optimize the design.Research limitations/implications: The components of a fatigue tester have to withstand the significant temperature differences in the range 30; +140˚C, e.g. hydraulic hoses, fittings, and pumps.Practical implications: We combine the analytical and experimental approach to provide customized and reliable engineering solution in the area of damper component seal development. A typical seal has a lip-like design protecting the moving parts against the leakage. It can be tested in a shock absorber or externally with use of a customized test rigs. Seal tests inside a shock absorber have numerous disadvantages. A shock absorber temperature rises during longer tests and cooling phase is required. This dramatically increases tests duration performed with the use of an expensive general-purpose hydraulic testing machinery. A compressed air or water jacket is used to accelerate the cooling process. Nevertheless, there are limitations related to the physics behind the cooling process. A seal component fatigue tester allows to perform the seal component tests out of the shock absorber.Originality/value: A new testing method provides possibility to quantify the main contributors of seal usage.

  3. Growth and reproduction in the Icelandic grey seal

    OpenAIRE

    2013-01-01

    Growth and reproduction in grey seals (Halichoerus grypus Fabricius, 1791) from Iceland were examined. The oldest Icelandic grey seals obtained were a 36 year old female and a 23 year old male. The longest animals were a 255 cm 13 year old male, and a 230 cm 20 year old female. The heaviest grey seal was an 11 year old male weighing 310 kg. The heaviest female was a 20 year old female that weighed 240 kg. Females reached an asymptotic standard length and weight of 200 (95% CI 196 - 204) cm an...

  4. Experimental study on a magnetofluid sealing liquid for propeller shaft

    Institute of Scientific and Technical Information of China (English)

    ZHAO Chang-fa; SUN Rong-hua; ZHENG Jin-xing

    2003-01-01

    The selecting and preparing method of the basic material of magnetic fluid was introduced. By using a chemical method, the magnetic micropowder Fe3O4 was successfully yielded, and an oil-base as a working carrier and dispersing agent was determined. The preparation process of the magnetic fluid and prescription of the oil-base magnetic fluid were discussed. The simulation experimental rig of magnetic fluid sealing for propeller shaft was designed. The sealing ability experiment was conducted and results were analyzed. The pressure of sealing is up to 2 Mpa.

  5. Study and Application of Sealing Material for Coke Oven Chamber

    Institute of Scientific and Technical Information of China (English)

    GAN Feifang; TAI Li

    2005-01-01

    A kind of dry refractory sealing material has been developed to repair the fine cracks in coke oven chamber. With silica sand as the main raw material, the sealing material is blown into coke oven chamber by compressed air while being applied, and bonded to brick surface or filled in fine cracks of chamber under right pressure. The physical properties of the material are similar to those of silica bricks during its application. So it can be adapted to conditions of coke oven and has good service life. The study and application results of the sealing material are described in this paper.

  6. Engineered glass seals for solid-oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Surdoval, Wayne; Lara-Curzio, Edgar; Stevenson, Jeffry; Muth, Joseph Thomas; Armstrong, Beth L.; Shyam, Amit; Trejo, Rosa M.; Wang, Yanli; Chou, Yeong Shyung; Shultz, Travis Ray

    2017-02-07

    A seal for a solid oxide fuel cell includes a glass matrix having glass percolation therethrough and having a glass transition temperature below 650.degree. C. A deformable second phase material is dispersed in the glass matrix. The second phase material can be a compliant material. The second phase material can be a crushable material. A solid oxide fuel cell, a precursor for forming a seal for a solid oxide fuel cell, and a method of making a seal for a solid oxide fuel cell are also disclosed.

  7. Low temperature hermetically sealed three-dimensional MEMS device for wireless optical communication

    Science.gov (United States)

    Agarwal, Rahul

    Novel processes were developed that resulted in a self-packaged device during the system integration, along with a transparent lid for inspection or optical probing. A new process was developed for improving the verticality in Micro Electro Mechanical Systems (MEMS) structures using Deep Reactive Ion Etching (DRIE). A self-pattered, mask-less photolithography technique was developed to metallize these vertical structures while maintaining a transparent window, for packaging of various MEMS devices. The verticality and metallization coverage were evaluated by incorporating the MEMS structures into an optical Corner Cube Retroreflector (CCR). A low temperature, hermetic sealing technique was also developed using In-Au thermo-compression bonding at 160°C. Cross-shaped 550microm deep vertical mirrors, with sidewall angles of 90.08° were etched with this new DRIE technique. This is the best reported sidewall angle for such deep structures. The typical scalloped DRIE sidewall roughness was reduced to 40nm using wet polishing. A bonded Pyrex wafer was used as the handle wafer during DRIE; it eventually forms the package window after DRIE. The metallized, vertical mirrors were bonded to a MEMS device chip to assemble and package the CCR. The MEMS device chip consisted of an array of torsion mirrors. The mirrors were designed to modulate at 6Vp-p--20V p-p, with the resonant frequencies ranging from 25 KHz--50 KHz. The design and simulation results are presented. To test the hermetic seal, helium leak tests were performed on the packaged device. Leak rates of as low as 2.8x10-8atm cc/s air were detected, which is better than the MIL-STD-883G of 5x10-8 atm cc/s air for a package volume of 7.8x10-3 CC. A microprocessor and temperature/humidity sensor was then integrated with the CCR to assemble a passive optical digital data communicator. A flexible circuit design and a folded packaging scheme were utilized to minimize the overall form factor. Flat, flexible polymer

  8. Chips with everything

    CERN Document Server

    CERN. Geneva

    2007-01-01

    In March 1972, Sir Robin Saxby gave a talk to the Royal Television Society called 'TV and Chips' about a 'state of the art' integrated circuit, containing 50 resistors and 50 transistors. Today's 'state of the art' chips contain up to a billion transistors. This enormous leap forward illustrates how dramatically the semiconductor industry has evolved in the past 34 years. The next 10 years are predicted to bring times of turbulent change for the industry, as more and more digital devices are used around the world. In this talk, Sir Robin will discuss the history of the Microchip Industry in parallel with ARM's history, demonstrating how a small European start-up can become a world player in the IT sector. He will also present his vision of important applications and developments in the next 20 years that are likely to become even more pervasive than the mobile phone is today, and will provide anecdotes and learning points from his own experience at ARM. About ARM: Sir Robin and a group of designers from Acorn...

  9. Packaging commercial CMOS chips for lab on a chip integration.

    Science.gov (United States)

    Datta-Chaudhuri, Timir; Abshire, Pamela; Smela, Elisabeth

    2014-05-21

    Combining integrated circuitry with microfluidics enables lab-on-a-chip (LOC) devices to perform sensing, freeing them from benchtop equipment. However, this integration is challenging with small chips, as is briefly reviewed with reference to key metrics for package comparison. In this paper we present a simple packaging method for including mm-sized, foundry-fabricated dies containing complementary metal oxide semiconductor (CMOS) circuits within LOCs. The chip is embedded in an epoxy handle wafer to yield a level, large-area surface, allowing subsequent photolithographic post-processing and microfluidic integration. Electrical connection off-chip is provided by thin film metal traces passivated with parylene-C. The parylene is patterned to selectively expose the active sensing area of the chip, allowing direct interaction with a fluidic environment. The method accommodates any die size and automatically levels the die and handle wafer surfaces. Functionality was demonstrated by packaging two different types of CMOS sensor ICs, a bioamplifier chip with an array of surface electrodes connected to internal amplifiers for recording extracellular electrical signals and a capacitance sensor chip for monitoring cell adhesion and viability. Cells were cultured on the surface of both types of chips, and data were acquired using a PC. Long term culture (weeks) showed the packaging materials to be biocompatible. Package lifetime was demonstrated by exposure to fluids over a longer duration (months), and the package was robust enough to allow repeated sterilization and re-use. The ease of fabrication and good performance of this packaging method should allow wide adoption, thereby spurring advances in miniaturized sensing systems.

  10. Wellbore Seal Repair Using Nanocomposite Materials

    Energy Technology Data Exchange (ETDEWEB)

    Stormont, John [Univ. of New Mexico, Albuquerque, NM (United States)

    2016-08-31

    Nanocomposite wellbore repair materials have been developed, tested, and modeled through an integrated program of laboratory testing and numerical modeling. Numerous polymer-cement nanocomposites were synthesized as candidate wellbore repair materials using various combinations of base polymers and nanoparticles. Based on tests of bond strength to steel and cement, ductility, stability, flowability, and penetrability in opening of 50 microns and less, we identified Novolac epoxy reinforced with multi-walled carbon nanotubes and/or alumina nanoparticles to be a superior wellbore seal material compared to conventional microfine cements. A system was developed for testing damaged and repaired wellbore specimens comprised of a cement sheath cast on a steel casing. The system allows independent application of confining pressures and casing pressures while gas flow is measured through the specimens along the wellbore axis. Repair with the nanocomposite epoxy base material was successful in dramatically reducing the flow through flaws of various sizes and types, and restoring the specimen comparable to an intact condition. In contrast, repair of damaged specimens with microfine cement was less effective, and the repair degraded with application of stress. Post-test observations confirm the complete penetration and sealing of flaws using the nanocomposite epoxy base material. A number of modeling efforts have supported the material development and testing efforts. We have modeled the steel-repair material interface behavior in detail during slant shear tests, which we used to characterize bond strength of candidate repair materials. A numerical model of the laboratory testing of damaged wellbore specimens was developed. This investigation found that microannulus permeability can satisfactorily be described by a joint model. Finally, a wellbore model has been developed that can be used to evaluate the response of the wellbore system (casing, cement, and microannulus

  11. DDT plus PCB's in blubber of harbor seals

    Energy Technology Data Exchange (ETDEWEB)

    Anas, R.E.

    1974-06-01

    Total amounts of DDT plus pcb's ranged from 380.7-2350.0 ppm in San Miguel Island seals; 459.4-1620.0 ppm in Puget Sound seals; 27.7-109.9 ppm in Columbia River seals; and 6.8-27.8 ppm in Pribilof Island seals sampled in 1971. (1 table)

  12. 76 FR 55332 - Federal Bureau of Investigation Anti-Piracy Warning Seal Program

    Science.gov (United States)

    2011-09-07

    ... From the Federal Register Online via the Government Publishing Office DEPARTMENT OF JUSTICE 41 CFR Part 128-1 RIN 1110-AA32 Federal Bureau of Investigation Anti-Piracy Warning Seal Program AGENCY...- Piracy Warning Seal (APW Seal). The proposed rule will provide access to the APW Seal to all...

  13. 10 CFR 35.500 - Use of sealed sources for diagnosis.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 1 2010-01-01 2010-01-01 false Use of sealed sources for diagnosis. 35.500 Section 35.500 Energy NUCLEAR REGULATORY COMMISSION MEDICAL USE OF BYPRODUCT MATERIAL Sealed Sources for Diagnosis § 35.500 Use of sealed sources for diagnosis. A licensee shall use only sealed sources for...

  14. Ultra-High Temperature Metallic Seal/Energizer Development for Aero Propulsion and Gas Turbine Applications

    Science.gov (United States)

    Cornett, Ken; Newman, Jesse; Datta, Amit

    2009-01-01

    The industry is requiring seals to operate at higher and higher temperatures. Traditional static seal designs and materials experience stress relaxation, losing their ability to maintain contact with moving flanges. Ultra High Temperature seal development program is a multiphase program with incremental increases in seal operating temperatures.

  15. The isolation and partial characterization of a highly pathogenic herpesvirus from the harbor seal (Phoca vitulina).

    NARCIS (Netherlands)

    A.D.M.E. Osterhaus (Albert); H. Yang (Hong); H.E.M. Spijkers (Ine); J. Groen (Jan); J.S. Teppema; G. van Steenis (Bert)

    1985-01-01

    textabstractThis report describes the first isolation and partial characterization of a herpesvirus from the harbor seal (Phoca vitulina). The virus was isolated during a disease outbreak in a group of young seals nursed in a seal orphanage in The Netherlands. Almost half of the seals died with symp

  16. Development of functional lab-on-a-chip on polymer for point-of-care testing of metabolic parameters.

    Science.gov (United States)

    Do, Jaephil; Lee, Sehwan; Han, Jungyup; Kai, Junhai; Hong, Chien-Chong; Gao, Chuan; Nevin, Joseph H; Beaucage, Gregory; Ahn, Chong H

    2008-12-01

    This paper presents the development of an easy-to-handle and disposable clinical diagnostic lab-on-a-chip using fully integrated plastic microfluidic components, which has the sampling/identifying capability to make fast and reliable measurements of metabolic parameters from human whole blood. A smart and functional lab-on-a-chip cartridge, which incorporates a full on-chip auto-calibration function for in the field applications, has been developed, and then fully characterized using a portable analyzer (3 (1/4)''x 5''x 1'') with multi-analyte detection capability. In addition, several new approaches in realizing smart and functional lab-on-a-chips on polymer have been adopted, which include the pinch valve for automatic fluidic sealing, a by-pass channel as the sampling indicator, and a robust connector design for long analyzer lifetimes. Metabolic parameters such as glucose, lactate, and partial oxygen from human whole blood have been successfully measured using the functional polymer lab-on-a-chips and the portable analyzer developed in this work.

  17. Measurement and theoretical analysis of the under-seal pressure of rotary engine apex seals. Rotary engine no apex seal no haiatsu no sokutei to kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Matsuura, K.; Terasaki, K. (Aoyama gakuin Univ., Tokyo (Japan). School of Science and Technology)

    1991-08-25

    A fundamental structure of an experimental rotary engine, which satisfies the conditions for the actual machine and can provide the phenomena on the rotor in multichannel electrical signals, and a method of taking out the signals have been developed. The pressures under two apex seals at medium speed and up to high load were measured to obtain some new knowledges. The pressure under the apex seal of 6mm thickness decreased considerably than that of the working chamber when the rotation speed increased with high loads. On the other hand, the decrease was little with the apex seal of 3mm thickness. The temperature of the gas flowing into the underseal chamber, temperature of the sealing groove wall, and the values of the pressures in the working chamber before and after apex seals measured by a pressure sensor provided in the housing were compared with the values calculated by theoretical analysis method for the underseal pressure to clarify the effect of each factor on the underseal pressure. 13 refs., 18 figs., 1 tab.

  18. S-Chip Technical Assistance

    Data.gov (United States)

    U.S. Department of Health & Human Services — The page will provide access to reports and other published products designed to assist states with complicated S-Chip technical issues. The reports and products...

  19. Handling of fuel chips - a health problem

    Energy Technology Data Exchange (ETDEWEB)

    Stroemquist, L.H.; Blomqvist, G.; Karlsson, E.; Vincent, A.; Lundgren, R.; Eliasson, L.

    1980-01-01

    An investigation has been made about health problems and occurrence of mold in connection with handling of fuel chips. The investigation was composed of three different parts. First, an inquiry was made to chip stokers about handling, storage etc. of chips as well as possible medical trouble. The answers indicated that symptoms on allergic alveolitis are common among chip stokers, 13% of the answers. Second, a determination of the proportion of living airborne colony-forming mold fungi was made at some chip using units. Third, a pilot study was made to examine the possibilities to improve storability of fuel chips using high-temperature drying.

  20. 7 CFR 201.36c - Hermetically-sealed containers.

    Science.gov (United States)

    2010-01-01

    ... allow water vapor penetration through any wall, including the seals, greater than 0.05 grams of water... percent and on the other side of 0 percent. Water vapor penetration or WVP is measured by the standards...

  1. Northern Fur Seal Captures and Tag Sightings Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset contains information regarding the capture, tagging and re-sighting of northern fur seals on the Pribilof Islands and Bogoslof Island, Alaska, from 1986...

  2. Seal Island and Franklin Island National Wildlife Refuges Trip Report

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This is a summary of visits to both Seal Island National Wildlife Refuge and Franklin Island National Wildlife Refuge on August 14, 15, 16, 1982.

  3. An application of small-gap equations in sealing devices

    Science.gov (United States)

    Vionnet, Carlos A.; Heinrich, Juan C.

    1993-01-01

    The study of a thin, incompressible Newtonian fluid layer trapped between two almost parallel, sliding surfaces has been actively pursued in the last decades. This subject includes lubrication applications such as slider bearings or the sealing of non-pressurized fluids with rubber rotary shaft seals. In the present work we analyze numerically the flow of lubricant fluid through a micro-gap of sealing devices. The first stage of this study is carried out assuming that a 'small-gap' parameter delta attains an extreme value in the Navier-Stokes equations. The precise meaning of small-gap is achieved by the particular limit delta = 0 which, within the bounds of the hypotheses, predicts transport of lubricant through the sealed area by centrifugal instabilities. Numerical results obtained with the penalty function approximation in the finite element method are presented. In particular, the influence of inflow and outflow boundary conditions, and their impact in the simulated flow, are discussed.

  4. WEAR AND SEALING CHARACTERISTICS OF ENGINE VALVE GUIDE

    Institute of Scientific and Technical Information of China (English)

    Qu Shengguan; Xia Wei; Han Lifa; Xiao Zhiyu; Chen Weiping; Li Yuanyuan

    2005-01-01

    A novel powder metallurgy (P/M) material with high wear resistance is developed in order to decrease the wear and lubricant-leakage of a diesel engine valve guide. The friction and wear tests of this material are conducted. It indicates that the wear resistance of the newly developed P/M material has been improved and much better than that of the formerly used alloy steel. Moreover, three different sealing structures are designed and theoretically analyzed with respect to the characteristic of hydrodynamic sealing. Through comparative experiments of component leakage and engine run-in for different valve guide structures, it proves that the structure with a machined sealing groove but not installed with a seal-ring cannot only reduce the specific lubricant consumption (SLC) of cylinder head, but also decrease the wear of valve stem and valve guide.

  5. End crop sealing method for spent nuclear fuel

    Energy Technology Data Exchange (ETDEWEB)

    Yamanaka, Kiyoshi

    1998-12-04

    End crops of spent nuclear fuels and glass materials are sealed in a corrosion and heat resistant vessel having an upper portion opened, and the corrosion and heat resistant vessel is heated from outside to melt the glass materials and they are solidified to form glass solidification products in which the end crops and radioactive materials deposited on the end crops are sealed. Then, the opened portion is closed. Since the end crops and radioactive materials deposited on end crops are sealed as glass solidification products in the vessel, sealing property for radioactive materials can be enhanced. Accordingly, radioactive materials can be prevented from transferring to the outside upon storing wastes or processing them into underground. In addition, since a large quantity of end crops can be filled into the corrosion and heat resistant vessel to form high level wastes, the space for the storage of wastes and processing facilities can be reduced. (T.M.)

  6. Seal assembly for materials with different coefficients of thermal expansion

    Science.gov (United States)

    Minford, Eric

    2009-09-01

    Seal assembly comprising (a) two or more seal elements, each element having having a coefficient of thermal expansion; and (b) a clamping element having a first segment, a second segment, and a connecting segment between and attached to the first and second segments, wherein the two or more seal elements are disposed between the first and second segments of the clamping element. The connecting segment has a central portion extending between the first segment of the clamping element and the second segment of the clamping element, and the connecting segment is made of a material having a coefficient of thermal expansion. The coefficient of thermal expansion of the material of the connecting segment is intermediate the largest and smallest of the coefficients of thermal expansion of the materials of the two or more seal elements.

  7. Seal Beach National Wildlife Refuge: Final Comprehensive Conservation Plan

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This Comprehensive Conservation Plan (CCP) was written to guide management on Seal Beach NWR for the next 15 years. This plan outlines the Refuge vision and purpose...

  8. Inflatable Module Seal Interface Development and Testing Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Inflatable structures will require low permeable bladder to metallic seal interface.  Cold flow of bladder materials over time is not acceptable for long term...

  9. LEGACY - EOP CRITTERCAM Deployments on French Frigate Shoals monk seals

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — CRITTERCAMs, were deployed on a 42 monk seals at French Frigate Shoals Hawaii. Sixty nine hours of video comprised of 3192 recording segments collected at...

  10. Aerial Survey Units for Harbor Seals in Coastal Alaska

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Aerial surveys of coastal Alaska are the primary method for estimating abundance of harbor seals. A particular challenge associated with aerial surveys of harbor...

  11. Extreme Environment Ceramic-to-Metal Seal Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed Phase 1 program will demonstrate the feasibility of large ceramic to metal joints/seals that can tolerate extreme environments. The immediate...

  12. Hiatal hernia in a harbor seal (Phoca vitulina) pup.

    Science.gov (United States)

    Biancani, Barbara; Field, Cara L; Dennison, Sophie; Pulver, Robert; Tuttle, Allison D

    2012-06-01

    A 2-wk-old stranded harbor seal (Phoca vitulina) rescued by Mystic Aquarium showed signs of the presence of a hiatal hernia during rehabilitation. Contrast radiographs of esophagus and stomach revealed an intrathoracic radiodensity that contains filling defects typical of stomach, consistent with gastric rugal folds. Mural thickening was observed at the level of the cardia consistent with a diagnosis of a hiatal hernia. Although clinical improvement was noted with medical therapy and tube feeding, surgical correction of the hiatal hernia was considered necessary for full resolution. However, owing to the animal's low body weight, the corrective hernia surgery was postponed until the body condition improved. The seal needed to be surgically treated for a corneal ulcer, and while anesthetized with isoflurane, the seal became dyspneic and developed cardiac arrhythmias; ultimately cardiac arrest ensued. Resuscitation was unsuccessfully attempted and the seal was euthanized. Necropsy confirmed the radiographic diagnosis and further characterized a paraesophageal hiatal hernia.

  13. Gamma-ray computed tomography to characterize soil surface sealing

    Energy Technology Data Exchange (ETDEWEB)

    Pires, L.F.Luiz F. E-mail: lfpires@cena.usp.br; Macedo, Jose R. de; Souza, Manoel D. de; Bacchi, Osny O.S.; Reichardt, Klaus

    2002-09-01

    The application of sewage sludge as a fertilizer on soils may cause compacted surface layers (surface sealing), which can promote changes on soil physical properties. The objective of this work was to study the use of gamma-ray computed tomography, as a diagnostic tool for the evaluation of this sealing process through the measurement of soil bulk density distribution of the soil surface layer of samples subjected to sewage sludge application. Tomographic images were taken with a first generation tomograph with a resolution of 1 mm. The image analysis opened the possibility to obtain soil bulk density profiles and average soil bulk densities of the surface layer and to detect the presence of soil surface sealing. The sealing crust thickness was estimated to be in the range of 2-4 mm.

  14. 49 CFR 236.553 - Seal, where required.

    Science.gov (United States)

    2010-10-01

    .... Seal shall be maintained on any device other than brake-pipe cut-out cock (double-heading cock), by means of which the operation of the pneumatic portion of automatic train-stop or train-control...

  15. Optical properties of end-sealed hollow fibers.

    Science.gov (United States)

    Mohri, Shintaro; Kasai, Takao; Abe, Yukio; Shi, Yi-Wei; Matsuura, Yuji; Miyagi, Mitsunobu

    2002-03-01

    We propose sealing techniques for medical hollow fibers to protect the inner surface of fibers from debris or water that scatters from targets. First, hollow fibers are sealed with a film of polymer that is easily formed by use of a dipping technique. The transmission loss of 20-microm-thick sealing film was 0.2 dB for Er:YAG laser light, and the maximum energy that is available for the film was 180 mJ. Second, a sealed glass cap was applied to the output end of hollow fiber. The silica-glass cap with a wall thickness of 400 microm shows a transmission loss of 0.5 dB and was not damaged by radiation of 400-mJ energy pulses.

  16. Evaluation of seals for high-performance cryogenic turbomachines

    Science.gov (United States)

    Hendricks, R. C.; Tam, L. T.; Braun, M. J.; Vlcek, B. L.

    1987-01-01

    An approach to computing flow and dynamic characteristics for seals or bearings is discussed. The local average velocity was strongly influenced by inlet and exit effects and fluid injection, which in turn drove zones of secondary flow. For the restricted three-dimensional model considered, the integral averaged results were in reasonable agreement with selected data. Unidirectional pressure measurements alone were insufficient to define such flow variations. However, for seal and bearing leakage correlations the principles of corresponding states were found to be useful. Also discussed are three phenomena encountered during testing of three eccentric nonrotating seal configurations for the Space Shuttle Main Engine (SSME) Program. Fluid injection, choking within a seal, and pressure profile crossover are related to postulated zones of secondary flow or separation and to direct stiffness.

  17. 78 FR 15669 - Marine Mammals: Alaska Harbor Seal Habitats

    Science.gov (United States)

    2013-03-12

    ... (i.e., charter boats In 2001, the Yakutat Tlingit Tribe expressed concern about a gradual seal... collaboration with the Yakutat Tlingit Tribe and Northwest Cruise Ship Association examined the effects...

  18. Recovering and Mining Asteroids with a Gas-Sealed Enclosure

    Science.gov (United States)

    Jenniskens, P.; Damer, B.; Norkus, R.; Pilotz, S.; Grigsby, B.; Adams, C.; Blair, B. R.

    2015-01-01

    The internal structure of weakly consolidated rubble piles and primitive asteroids can be studied closer to home, and such asteroids can be mined, if it is possible to create a gas-sealed enclosure around the asteroid.

  19. The Trail Inventory of Seal Beach NWR [Cycle 2

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The purpose of this report is to create a baseline inventory of all non-motorized trails on Seal Beach National Wildlife Refuge. Trails in this inventory are...

  20. Measure Guideline: Sealing and Insulating of Ducts in Existing Homes

    Energy Technology Data Exchange (ETDEWEB)

    Aldrich, R.; Puttagunta, S.

    2011-12-01

    This document begins with a discussion on potential cost and performance benefits of duct sealing and insulating. It continues with a review of typical duct materials and components and the overall procedures for assessing and improving the duct system.

  1. Measure Guideline. Sealing and Insulating Ducts in Existing Homes

    Energy Technology Data Exchange (ETDEWEB)

    Aldrich, R. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Puttagunta, S. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2011-12-01

    This document begins with a discussion on potential cost and performance benefits of duct sealing and insulating. It continues with a review of typical duct materials and components and the overall procedures for assessing and improving the duct system.

  2. Northern fur seal pup weights, Pribilof Islands, Alaska, 1957-present

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This database contains northern fur seal pup mass and length data by date, island, rookery and sex on the Pribilof Islands, Alaska, collected between 1957-2012. Mass...

  3. 75 FR 16149 - Medicaid and CHIP Programs; Meeting of the CHIP Working Group-April 26, 2010

    Science.gov (United States)

    2010-03-31

    ... Administration Medicaid and CHIP Programs; Meeting of the CHIP Working Group-- April 26, 2010 AGENCIES: Centers...-Sponsored Coverage Coordination Working Group (referred to as the ``CHIP Working Group''). The CHIP Working... Medicaid, CHIP, and Employer-Sponsored Coverage Coordination Working Group (``CHIP Working......

  4. Tunable on chip optofluidic laser

    DEFF Research Database (Denmark)

    Bakal, Avraham; Vannahme, Christoph; Kristensen, Anders

    2016-01-01

    On chip tunable laser is demonstrated by realizing a microfluidic droplet array. The periodicity is controlled by the pressure applied to two separate inlets, allowing to tune the lasing frequency over a broad spectral range.......On chip tunable laser is demonstrated by realizing a microfluidic droplet array. The periodicity is controlled by the pressure applied to two separate inlets, allowing to tune the lasing frequency over a broad spectral range....

  5. Experimental Study on Leakage Flow in Labyrinth Seals with Asymmetric Geometries

    Science.gov (United States)

    Nishii, Kazufumi; Furukawa, Akinori; Watanabe, Satoshi; Miyake, Kunihiro

    2010-06-01

    The labyrinth seal is one of non-contact seals, which is used as a seal device of rotary machines from reasons of the lubrication free and small losses. So far, many researchers have investigated the characteristics and suitable geometries of labyrinth seals, though only one directional flow of the seal has been focused up to now. As flow direction in the seal becomes changeable depending on the gas-purge system and the inner pressure variation of machines for recent applications, a guideline of designing labyrinth seal with changeable flow directions is required. In the present report, effects of seal characteristics and internal flow behaviors on various shapes of asymmetric convexity in labyrinth seals are experimentally investigated and relations between pressure loss and convexity geometries are discussed for designing a suitable seal.

  6. Measure Guideline: Air Sealing Attics in Multifamily Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Otis, C.; Maxwell, S.

    2012-06-01

    This Building America Measure Guideline is intended for owners, builders, contractors, homeowners, and other stakeholders in the multifamily building industry, and focuses on challenges found in existing buildings for a variety of housing types. It explains why air sealing is desirable, explores related health and safety issues, and identifies common air leakage points in multifamily building attics. In addition, it also gives an overview of materials and techniques typically used to perform air sealing work.

  7. Measure Guideline. Air Sealing Attics in Multifamily Buildings

    Energy Technology Data Exchange (ETDEWEB)

    Otis, Casey [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Maxwell, Sean [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2012-06-01

    This Building America Measure Guideline is intended for owners, builders, contractors, homeowners, and other stakeholders in the multifamily building industry, and focuses on challenges found in existing buildings for a variety of housing types. It explains why air sealing is desirable, explores related health and safety issues, and identifies common air leakage points in multifamily building attics. In addition, it also gives an overview of materials and techniques typically used to perform air sealing work.

  8. Experimental study of ceramic coated tip seals for turbojet engines

    Science.gov (United States)

    Biesiadny, T. J.; Klann, G. A.; Lassow, E. S.; Mchenry, M.; Mcdonald, G.; Hendricks, R. C.

    1985-01-01

    Ceramic gas-path seals were fabricated and successfully operated over 1000 cycles from flight idle to maximum power in a small turboshaft engine. The seals were fabricated by plasma spraying zirconia over a NiCoCrAlX bond boat on the Haynes 25 substrate. Coolant-side substrate temperatures and related engine parameters were recorded. Post-test inspection revealed mudflat surface cracking with penetration to the ceramic bond-coat interface.

  9. Adhesion of Silicone Elastomer Seals for NASA's Crew Exploration Vehicle

    Science.gov (United States)

    deGroh, Henry C., III; Miller, Sharon K. R.; Smith, Ian M.; Daniels, Christopher C.; Steinetz, Bruce M

    2008-01-01

    Silicone rubber seals are being considered for a number of interfaces on NASA's Crew Exploration Vehicle (CEV). Some of these joints include the docking system, hatches, and heat shield-to-back shell interface. A large diameter molded silicone seal is being developed for the Low Impact Docking System (LIDS) that forms an effective seal between the CEV and International Space Station (ISS) and other future Constellation Program spacecraft. Seals between the heat shield and back shell prevent high temperature reentry gases from leaking into the interface. Silicone rubber seals being considered for these locations have inherent adhesive tendencies that would result in excessive forces required to separate the joints if left unchecked. This paper summarizes adhesion assessments for both as-received and adhesion-mitigated seals for the docking system and the heat shield interface location. Three silicone elastomers were examined: Parker Hannifin S0899-50 and S0383-70 compounds, and Esterline ELA-SA-401 compound. For the docking system application various levels of exposure to atomic oxygen (AO) were evaluated. Moderate AO treatments did not lower the adhesive properties of S0899-50 sufficiently. However, AO pretreatments of approximately 10(exp 20) atoms/sq cm did lower the adhesion of S0383-70 and ELA-SA-401 to acceptable levels. For the heat shield-to-back shell interface application, a fabric covering was also considered. Molding Nomex fabric into the heat shield pressure seal appreciably reduced seal adhesion for the heat shield-to-back shell interface application.

  10. Sealing and anti-corrosive action of tannin rust converters

    Energy Technology Data Exchange (ETDEWEB)

    Gust, J.; Bobrowicz, J. (Building Research Inst., Warsaw (Poland))

    1993-01-01

    A possibility of the application of mercury porosimetry in the investigation on porosity in corrosion products of the carbon steel along with the degree of sealing by the use of tannin rust converters is presented. The effect of the atmospheric humidity on the rust conversion including the time of that conversion on the degree of rust sealing is discussed. The results of the corrosion investigation of carbon steel covered with a layer of the rust converted with tannin-containing agents are presented.

  11. Filled glass composites for sealing of solid oxide fuel cells.

    Energy Technology Data Exchange (ETDEWEB)

    Tandon, Rajan; Widgeon, Scarlett Joyce; Garino, Terry J.; Brochu, Mathieu; Gauntt, Bryan D.; Corral, Erica L.; Loehman, Ronald E.

    2009-04-01

    Glasses filled with ceramic or metallic powders have been developed for use as seals for solid oxide fuel cells (SOFC's) as part of the U.S. Department of Energy's Solid State Energy Conversion Alliance (SECA) Program. The composites of glass (alkaline earth-alumina-borate) and powders ({approx}20 vol% of yttria-stabilized zirconia or silver) were shown to form seals with SOFC materials at or below 900 C. The type and amount of powder were adjusted to optimize thermal expansion to match the SOFC materials and viscosity. Wetting studies indicated good wetting was achieved on the micro-scale and reaction studies indicated that the degree of reaction between the filled glasses and SOFC materials, including spinel-coated 441 stainless steel, at 750 C is acceptable. A test rig was developed for measuring strengths of seals cycled between room temperature and typical SOFC operating temperatures. Our measurements showed that many of the 410 SS to 410 SS seals, made using silver-filled glass composites, were hermetic at 0.2 MPa (2 atm.) of pressure and that seals that leaked could be resealed by briefly heating them to 900 C. Seal strength measurements at elevated temperature (up to 950 C), measured using a second apparatus that we developed, indicated that seals maintained 0.02 MPa (0.2 atm.) overpressures for 30 min at 750 C with no leakage. Finally, the volatility of the borate component of sealing glasses under SOFC operational conditions was studied using weight loss measurements and found by extrapolation to be less than 5% for the projected SOFC lifetime.

  12. Laboratory Testing of Aerosol for Enclosure Air Sealing

    Energy Technology Data Exchange (ETDEWEB)

    Harrington, C.; Modera, M.

    2012-05-01

    Space conditioning energy use can be significantly reduced by addressing uncontrolled infiltration and exfiltration through the envelope of a building. A process for improving the air tightness of a building envelope by sealing shell leaks with an aerosol sealing technology is presented. Both retrofit and new construction applications are possible through applying this process either in attics and crawlspaces or during rough-in stage.

  13. Rotordynamics of Turbine Labyrinth Seals with Rotor Axial Shifting

    OpenAIRE

    Jinxiang Xi; Rhode, David L.

    2006-01-01

    Rotors in high-performance steam turbines experience a significant axial shifting during starting and stopping processes due to thermal expansion, for example. This axial shifting could significantly alter the flow pattern and the flow-induced rotordynamic forces in labyrinth seals, which in turn, can considerably affect the rotor-seal system performance. This paper investigates the influence of the rotor axial shifting on leakage rate as well as rotordynamic forces in hi...

  14. Toward a predictive model for elastomer seals

    Science.gov (United States)

    Molinari, Nicola; Khawaja, Musab; Sutton, Adrian; Mostofi, Arash

    Nitrile butadiene rubber (NBR) and hydrogenated-NBR (HNBR) are widely used elastomers, especially as seals in oil and gas applications. During exposure to well-hole conditions, ingress of gases causes degradation of performance, including mechanical failure. We use computer simulations to investigate this problem at two different length and time-scales. First, we study the solubility of gases in the elastomer using a chemically-inspired description of HNBR based on the OPLS all-atom force-field. Starting with a model of NBR, C=C double bonds are saturated with either hydrogen or intramolecular cross-links, mimicking the hydrogenation of NBR to form HNBR. We validate against trends for the mass density and glass transition temperature for HNBR as a function of cross-link density, and for NBR as a function of the fraction of acrylonitrile in the copolymer. Second, we study mechanical behaviour using a coarse-grained model that overcomes some of the length and time-scale limitations of an all-atom approach. Nanoparticle fillers added to the elastomer matrix to enhance mechanical response are also included. Our initial focus is on understanding the mechanical properties at the elevated temperatures and pressures experienced in well-hole conditions.

  15. Radioactivity Confinement Studies Within the SEAL Program

    Science.gov (United States)

    Collén, Jan; Matsugu, Ron; Natalizio, Antonio; Shen, Kecheng

    1997-09-01

    In the framework of the European SEAL program, investigations have been performed with the aim of optimizing the second confinement function and plant layout with respect to normal operation as well as abnormal operation, including accident conditions. This has been done for two conceptual fusion reactor designs: one using water as the coolant and the other using helium. The starting point of these investigations was the SEAFP project design. For the water-cooled reactor design the studies were focused on design options such as pressure suppression spray system, pressure suppression pool with closed containment or with venting to gravel bed filter and stack, and separate expansion volume optionally operated with a vacuum and equipped with spray system. Similar analyses were performed for the helium-cooled reactor design. The analyses were focused on design options comprising a single, large confinement volume or a vent duct connected to an expansion volume operated at vacuum in comparison with the SEAFP Model 1. The thermal-hydraulic analyses performed with the MELCOR code provide an integrated assessment of the cooling loop and confinement system dynamics.

  16. Retrograde seal in ultrasonically prepared canals.

    Science.gov (United States)

    Sutimuntanakul, S; Worayoskowit, W; Mangkornkarn, C

    2000-08-01

    The sealing ability of various retrofilling materials was compared. The root canals of 85 single-rooted teeth were cleansed and obturated with gutta-percha without sealer using lateral condensation. The apical 3 mm of the roots were resected and divided into positive control, negative control, and five experimental groups. The experimental teeth received root-end cavity preparation to 3 mm depth using an ultrasonic retroprep tip. The retrocavities were dried and divided into five groups to receive the following materials: amalgam with varnish, amalgam with Clearfil Liner Bond II, thermoplasticized gutta-percha (TGP) with sealer, Ketac-fil, and Super-EBA. After immersion in India ink for 7 days, the roots were demineralized, cleared, and evaluated for dye leakage under a stereomicroscope. Statistical analysis showed that Super-EBA, Ketac-fil, and TGP with sealer demonstrated less leakage than amalgam with varnish and amalgam with Clearfil Liner Bond II (p fil or TGP sealer (p fil and TGP or between the two groups filled with amalgam (p > 0.05).

  17. Catch history of ringed seals (Phoca hispida in Canada

    Directory of Open Access Journals (Sweden)

    Randall R Reeves

    1998-06-01

    Full Text Available The ringed seal (Phoca hispida has always been a staple in the diet and household economy of Inuit in Canada. The present paper was prepared at the request of the NAMMCO Scientific Committee to support their assessment of ringed seal stocks in the North Atlantic Basin and adjacent arctic and subarctic waters. Specifically, our objective was to evaluate recent and current levels of use of ringed seals by Canadian Inuit. Annual removals probably were highest (possibly greater than 100,000 in the 1960s and 1970s, a period when sealskin prices were particularly strong. Catches declined substantially in the 1980s following a collapse in sealskin prices, presumably related to the European trade ban on skins from newborn harp and hooded seals (Phoca groenlandica and Cystophora cristata, respectively. Recent catch levels throughout Canada (1980s and early 1990s are believed to be in the order of 50,000 to 65,000 ringed seals, with a total average annual kill (including hunting loss in the high tens of thousands. No reliable system is in place to monitor catches of ringed seals, so any estimate must be derived from a heterogeneous array of sources.

  18. Tags and seals to strengthen arms control verification

    Energy Technology Data Exchange (ETDEWEB)

    DeVolpi, A.

    1990-10-03

    Tags and seals have long been recognized as important tools in arms control. The trend in control of armaments is to limit militarily significant equipment that is capable of being verified through direct and cooperative means, chiefly on-site inspection or monitoring. Although this paper will focus on the CFE treaty, the role of tags and seals for other treaties will also be addressed. Published technology and concepts will be reviewed, based on open sources. Arms control verification tags are defined as unique identifiers designed to be tamper-revealing; in that respect, seals are similar, being used as indicators of unauthorized access. Tamper-revealing tags are intended as single-point markers, seals for two-point couplings, and nets for volume containment. Seals usually bind two separate components, such as a hatch or flange that provides access to a secure compartment or a valve that controls fluid flow. A tamper-revealing net might be comprised of a coupled fiberoptic bundle wrapped around an object. Sometimes the term ``seal`` is used to denote the tamper-revealing feature of a tag that is attached to a surface, but in this paper the tamper-indicating connection is considered to be part of the tag concept itself.

  19. Could seals prevent cod recovery in the Baltic Sea?

    Directory of Open Access Journals (Sweden)

    Brian R MacKenzie

    Full Text Available Fish populations are increasingly affected by multiple human and natural impacts including exploitation, eutrophication, habitat alteration and climate change. As a result many collapsed populations may have to recover in ecosystems whose structure and functioning differ from those in which they were formerly productive and supported sustainable fisheries. Here we investigate how a cod (Gadus morhua population in the Baltic Sea whose biomass was reduced due to a combination of high exploitation and deteriorating environmental conditions might recover and develop in the 21st century in an ecosystem that likely will change due to both the already started recovery of a cod predator, the grey seal Halichoerus grypus, and projected climate impacts. Simulation modelling, assuming increased seal predation, fishing levels consistent with management plan targets and stable salinity, shows that the cod population could reach high levels well above the long-term average. Scenarios with similar seal and fishing levels but with 15% lower salinity suggest that the Baltic will still be able to support a cod population which can sustain a fishery, but biomass and yields will be lower. At present knowledge of cod and seal interactions, seal predation was found to have much lower impact on cod recovery, compared to the effects of exploitation and salinity. These results suggest that dual management objectives (recovery of both seal and cod populations are realistic but success in achieving these goals will also depend on how climate change affects cod recruitment.

  20. Shape memory alloy seals for geothermal applications. Final report. Report ESG-82-14

    Energy Technology Data Exchange (ETDEWEB)

    Friske, Warren H.; Schwartzbart, Harry

    1982-07-30

    A novel temperature-actuated seal for geothermal applications is under development. This program uses the shape memory property of nickel-titanium (Nitinol) alloys to achieve an improved seal in geothermal downhole pumps. Nitinol flange face seals and pump shaft seals have been designed, fabricated, and tested. It has been demonstrated that the shape memory effect of Nitinol alloys can be utilized to activate and maintain a leaktight seal in geothermal environments.

  1. Universal Fingerprinting Chip Server

    Science.gov (United States)

    Casique-Almazán, Janet; Larios-Serrato, Violeta; Olguín-Ruíz, Gabriela Edith; Sánchez-Vallejo, Carlos Javier; Maldonado-Rodríguez, Rogelio; Méndez-Tenorio, Alfonso

    2012-01-01

    The Virtual Hybridization approach predicts the most probable hybridization sites across a target nucleic acid of known sequence, including both perfect and mismatched pairings. Potential hybridization sites, having a user-defined minimum number of bases that are paired with the oligonucleotide probe, are first identified. Then free energy values are evaluated for each potential hybridization site, and if it has a calculated free energy of equal or higher negative value than a user-defined free energy cut-off value, it is considered as a site of high probability of hybridization. The Universal Fingerprinting Chip Applications Server contains the software for visualizing predicted hybridization patterns, which yields a simulated hybridization fingerprint that can be compared with experimentally derived fingerprints or with a virtual fingerprint arising from a different sample. Availability http://bioinformatica.homelinux.org/UFCVH/ PMID:22829736

  2. Application of Asphalt Rubber Seal Coat Gravel Synchronization in Highway Maintenance%橡胶沥青碎石同步封层在公路养护中的应用

    Institute of Scientific and Technical Information of China (English)

    肖文平; 王勇

    2016-01-01

    Synchronous chip sealer 90s century technology application and promotion in Europe in recent years, synchronous chip seal layer applied in our country has become increasingly widespread.It can be used as a seal coat of asphalt pavement preventive maintenance,and can be used as a sealing layer and a new highway under stress absorbing layer,but also as a bridge deck waterproofing layer,with good road performance,especially modified asphalt synchronous chip sealer,asphalt rubber synchronous chip sealer has both good waterproof effect,crack and has a good effect,to prevent and delay the semi-rigid base reflective crack has a good effect,simple construction and low cost.Through the application of synchronous asphalt rubber chip seal road preventive maintenance in its process principle,construction technology,performance characteristics were discussed.%同步碎石封层技术上世纪90年代在欧美得到应用和推广,近年来,同步碎石封层在我国的应用也越来越广泛。它既可以作为上封层用于沥青路面预防性养护,又可以用作新建公路下封层和应力吸收层,还可作为桥面防水层,具有良好的路用性能,特别是改性沥青同步碎石封层、橡胶沥青同步碎石封层既具有良好的防水效果,也有较好的防裂效果,对防止和延缓半刚性基层反射裂缝有较好效果,施工简单,成本低廉。文中通过橡胶沥青同步碎石封层在公路预防性养护中的应用对其工艺原理,施工技术,性能特点等进行了探讨。

  3. Final report of the rock sealing project. Sealing of zones disturbed by blasting and stress release

    Energy Technology Data Exchange (ETDEWEB)

    Boergesson, L.; Pusch, R.; Fredriksson, A.; Hoekmark, H.; Karnland, O.; Sanden, T. (Clay Technology AB, Lund (Sweden))

    1992-04-01

    Test 2 and 3 of the rock sealing project comprised determination of the hydraulic properties of the disturbed rock around tunnels and drifts and the possibilities of decreasing the hydraulic conductivity of the disturbed zones by an attempt to seal the very fine excavation-induced fractures that cause an increase in conductivity. This report deals with the grouting procedures and their effect while the hydraulic testing before grouting is described in volume 2. The macro flow test of the BMT drift before grouting showed that the disturbed zone around the drift has a highly increased hydraulic conductivity reaching more than 1 m into the rock from the periphery of the drift. The most conductive shallow part of this zone was grouted by 350 1 m long 'hedgehog' holes. The holes were injected with cement using dynamic as well as static techniques. The injections were preceded by laboratory investigations of the rheological properties of different cement mixtures, by theoretical modelling of grout penetration in factures, and by full scale injections in an artificial fracture. The macro flow test was repeated after the grouting and the results evaluated by using the same finite element models as before the grouting. The conclusion was that the effect of the grouting was very small. Excavation of the rock after grouting showed that the grout penetration has been very poor into chlorite-coated fractures and a conclusion was that such fractures are hardly groutable due to debris hindering the grout from penetrating. (au).

  4. Replacement of nickel sealing rings by expanded graphite sealing rings -upgrading of SG primary collector flange connection

    Energy Technology Data Exchange (ETDEWEB)

    Cikryt, F.; Bednarek, L.; Kusyn, L. [Vitkovice, Ostrava (Switzerland)

    1997-12-31

    One of the most loaded parts of a steam generator of VVER 440 MW type are the bolts and thread holes of the primary collector cover sealing set. The strength calculations and tensometric measurings performed during operation proved the high degree of a load on the bolts. The conditions of the stress limitation are not met in some cases according to the pertinent standards. The untightnesses at nickel rings occurred during putting the units of Jaslovske Bohunice and Dukovany nuclear power stations into operation. With regard to improve the reliability, the producer has taken measures to improve the quality of the rings and users have introduced more strict regulations for bolts tightening. Due to these measures the high reliability of the set has been obtained from point of view of the tightness, but substantial reduction of bolts and holes threads loading have not been obtained. Several years operation experience proved relatively low service of bolts, damage of thread holes and sealing grooves. As the degree of mechanical load is one of the vital parameters influencing the damage of sealing set, in 1996 we started with the works aimed at a possibility of nickel sealing rings replacement for a more modern type of sealing which assure the higher reliability and service life of the individual part of sealing set under the reduced load.

  5. Process for 3D chip stacking

    Science.gov (United States)

    Malba, Vincent

    1998-01-01

    A manufacturable process for fabricating electrical interconnects which extend from a top surface of an integrated circuit chip to a sidewall of the chip using laser pantography to pattern three dimensional interconnects. The electrical interconnects may be of an L-connect or L-shaped type. The process implements three dimensional (3D) stacking by moving the conventional bond or interface pads on a chip to the sidewall of the chip. Implementation of the process includes: 1) holding individual chips for batch processing, 2) depositing a dielectric passivation layer on the top and sidewalls of the chips, 3) opening vias in the dielectric, 4) forming the interconnects by laser pantography, and 5) removing the chips from the holding means. The process enables low cost manufacturing of chips with bond pads on the sidewalls, which enables stacking for increased performance, reduced space, and higher functional per unit volume.

  6. Process for 3D chip stacking

    Science.gov (United States)

    Malba, V.

    1998-11-10

    A manufacturable process for fabricating electrical interconnects which extend from a top surface of an integrated circuit chip to a sidewall of the chip using laser pantography to pattern three dimensional interconnects. The electrical interconnects may be of an L-connect or L-shaped type. The process implements three dimensional (3D) stacking by moving the conventional bond or interface pads on a chip to the sidewall of the chip. Implementation of the process includes: (1) holding individual chips for batch processing, (2) depositing a dielectric passivation layer on the top and sidewalls of the chips, (3) opening vias in the dielectric, (4) forming the interconnects by laser pantography, and (5) removing the chips from the holding means. The process enables low cost manufacturing of chips with bond pads on the sidewalls, which enables stacking for increased performance, reduced space, and higher functional per unit volume. 3 figs.

  7. Comparison of two ultrasonic coagulating shears in sealing pulmonary vessels

    Directory of Open Access Journals (Sweden)

    Raghavan D

    2013-03-01

    Full Text Available Devanathan Raghavan,1 John A Howington,2 Duan Broughton,1 Cortney E Henderson,1 Jeffrey W Clymer1 1Preclinical Research, Ethicon Endo-Surgery, Cincinnati, OH, USA; 2NorthShore University HealthSystem, Chicago, IL, USA Abstract: Ultrasonic cutting and coagulating devices have been used successfully in thoracic applications such as pulmonary resection or artery harvesting, but few studies have evaluated their use in sealing pulmonary vessels. In this study we compared two commercially available devices, Harmonic Ace+ (HAR, Ethicon Endo-Surgery, Inc., Cincinnati OH, USA and SonoSurg (SS, Olympus America, Center Valley, PA, USA, in a canine preclinical model. There were three sections to the study: acute, survival, and ex vivo (burst pressure. Hemostasis of sealed pulmonary arteries and veins was assessed for the initial application and during a simulated hypertensive crisis, both immediately after vessel sealing and after a survival period of 30 days. Other intraoperative measures were also evaluated, including transection time, tissue sticking, tissue tags, and char on the seal. Histological evaluation was performed both after initial sealing and after the survival period. Burst pressure of sealed vessels was measured ex vivo. For both devices, hemostasis was excellent, including those measurements made under simulated hypertensive crisis. There were no differences in any of the intraoperative measures or thermal damage evaluated histologically. Wound healing was normal. The burst pressures for ex vivo vessels sealed by HAR (median 619.2 mmHg were significantly higher than those of SS (350.3 mmHg, P = 0.022. Both devices displayed acceptable characteristics in sealing canine pulmonary arteries and veins. The only difference observed was that HAR produced burst pressures 76.8% greater than SS, which may lead to a lower percentage of failures in the region of physiological interest. Use of ultrasonic devices in thoracic applications provides a high

  8. Capillary-driven multiparametric microfluidic chips for one-step immunoassays.

    Science.gov (United States)

    Gervais, Luc; Hitzbleck, Martina; Delamarche, Emmanuel

    2011-09-15

    Here we present a capillary-driven microfluidic chip for "one-step" immunoassays. The chip allows for easy modification of several assay parameters such as the flow rates of sample, the volumes of samples for tests, and the type of reagents and receptors for detecting analytes. We therefore term such a chip a multiparametric chip and illustrate this concept with the integration and release of anti-C-reactive protein (CRP) detection antibodies (dAbs) together with splitting flow of samples containing CRP across lines of anti-CRP capture antibodies (cAbs). The microfluidic chip is fabricated in Si and is sealed with polydimethylsiloxane (PDMS) patterned with cAbs. The microfluidic chip is ∼1.7×3.4 cm(2) and is capable of analyzing 20 μL of human serum in 6 parallel flow paths with a range of flow rates from 3.3 nL s(-1) to 0.46 nL s(-1). An inkjet spotter was used to deposit 10.6 nL of dAb solution in a structure vicinal to the main flow path of the chip. The consequent asymmetric release of dAbs in a stream of human serum is compensated by a Dean flow mixer having 9 mixing loops and a footprint of 2.8 mm × 0.78 mm. The quantity of dAb present in the half of the flow path close to the spotting region decreases from 83% at the entrance of the mixer to 52% in the region after the mixer. The sample is then equally split into 6 reaction chambers and proceeds via connecting channels to 2 μL capillary pumps. The hydraulic resistance of the connecting channels is designed to vary flow rates, and therefore the kinetics of capture of CRP-dAb complexes, from 10 min to 72 min. The increased incubation time leads to a fourfold increase in detection signal in the reaction chamber with the longer incubation time. The concept presented here is flexible and suited for implementing various surface fluorescence immunoassays on a capillary-driven microfluidic chip.

  9. Development of Mechanical Sealing and Laser Welding Technology to Instrument Thermocouple for Nuclear Fuel Test Rod

    Energy Technology Data Exchange (ETDEWEB)

    Joung, Chang-Young; Ahn, Sung-Ho; Hong, Jin-Tae; Kim, Ka-Hye; Huh, Sung-Ho [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Zircaloy-4 of the nuclear fuel test rod, AISI 316L of the mechanical sealing parts, and the MI (mineral insulated) cable at a thermocouple instrumentation are hetero-metals, and are difficult to weld to dissimilar materials. Therefore, a mechanical sealing method to instrument the thermocouple should be conducted using two kinds of sealing process as follows: One is a mechanical sealing process using Swagelok, which is composed of sealing components that consists of an end-cap, a seal tube, a compression ring and a Swagelok nut. The other is a laser welding process used to join a seal tube, and an MI cable, which are made of the same material. The mechanical sealing process should be sealed up with the mechanical contact compressed by the strength forced between a seal tube and an end-cap, and the laser welding process should be conducted to have no defects on the sealing area between a seal tube and an MI cable. Therefore, the mechanical sealing and laser welding techniques need to be developed to accurately measure the centerline temperature of the nuclear fuel test rod in an experimental reactor. The mechanical sealing and laser welding tests were conducted to develop the thermocouple instrumentation techniques for the nuclear fuel test rod. The optimum torque value of a Swagelok nut to seal the mechanical sealing part between the end-cap and seal tube was established through various torque tests using a torque wrench. The optimum laser welding conditions to seal the welding part between a seal tube and an MI cable were obtained through various welding tests using a laser welding system.

  10. Molecular epidemiology of seal parvovirus, 1988-2014.

    Science.gov (United States)

    Bodewes, Rogier; Hapsari, Rebriarina; Rubio García, Ana; Sánchez Contreras, Guillermo J; van de Bildt, Marco W G; de Graaf, Miranda; Kuiken, Thijs; Osterhaus, Albert D M E

    2014-01-01

    A novel parvovirus was discovered recently in the brain of a harbor seal (Phoca vitulina) with chronic meningo-encephalitis. Phylogenetic analysis of this virus indicated that it belongs to the genus Erythroparvovirus, to which also human parvovirus B19 belongs. In the present study, the prevalence, genetic diversity and clinical relevance of seal parvovirus (SePV) infections was evaluated in both harbor and grey seals (Halichoerus grypus) that lived in Northwestern European coastal waters from 1988 to 2014. To this end, serum and tissue samples collected from seals were tested for the presence of seal parvovirus DNA by real-time PCR and the sequences of the partial NS gene and the complete VP2 gene of positive samples were determined. Seal parvovirus DNA was detected in nine (8%) of the spleen tissues tested and in one (0.5%) of the serum samples tested, including samples collected from seals that died in 1988. Sequence analysis of the partial NS and complete VP2 genes of nine SePV revealed multiple sites with nucleotide substitutions but only one amino acid change in the VP2 gene. Estimated nucleotide substitution rates per year were 2.00 × 10(-4) for the partial NS gene and 1.15 × 10(-4) for the complete VP2 gene. Most samples containing SePV DNA were co-infected with phocine herpesvirus 1 or PDV, so no conclusions could be drawn about the clinical impact of SePV infection alone. The present study is one of the few in which the mutation rates of parvoviruses were evaluated over a period of more than 20 years, especially in a wildlife population, providing additional insights into the genetic diversity of parvoviruses.

  11. Molecular epidemiology of seal parvovirus, 1988-2014.

    Directory of Open Access Journals (Sweden)

    Rogier Bodewes

    Full Text Available A novel parvovirus was discovered recently in the brain of a harbor seal (Phoca vitulina with chronic meningo-encephalitis. Phylogenetic analysis of this virus indicated that it belongs to the genus Erythroparvovirus, to which also human parvovirus B19 belongs. In the present study, the prevalence, genetic diversity and clinical relevance of seal parvovirus (SePV infections was evaluated in both harbor and grey seals (Halichoerus grypus that lived in Northwestern European coastal waters from 1988 to 2014. To this end, serum and tissue samples collected from seals were tested for the presence of seal parvovirus DNA by real-time PCR and the sequences of the partial NS gene and the complete VP2 gene of positive samples were determined. Seal parvovirus DNA was detected in nine (8% of the spleen tissues tested and in one (0.5% of the serum samples tested, including samples collected from seals that died in 1988. Sequence analysis of the partial NS and complete VP2 genes of nine SePV revealed multiple sites with nucleotide substitutions but only one amino acid change in the VP2 gene. Estimated nucleotide substitution rates per year were 2.00 × 10(-4 for the partial NS gene and 1.15 × 10(-4 for the complete VP2 gene. Most samples containing SePV DNA were co-infected with phocine herpesvirus 1 or PDV, so no conclusions could be drawn about the clinical impact of SePV infection alone. The present study is one of the few in which the mutation rates of parvoviruses were evaluated over a period of more than 20 years, especially in a wildlife population, providing additional insights into the genetic diversity of parvoviruses.

  12. Environmental predictors of ice seal presence in the Bering Sea.

    Science.gov (United States)

    Miksis-Olds, Jennifer L; Madden, Laura E

    2014-01-01

    Ice seals overwintering in the Bering Sea are challenged with foraging, finding mates, and maintaining breathing holes in a dark and ice covered environment. Due to the difficulty of studying these species in their natural environment, very little is known about how the seals navigate under ice. Here we identify specific environmental parameters, including components of the ambient background sound, that are predictive of ice seal presence in the Bering Sea. Multi-year mooring deployments provided synoptic time series of acoustic and oceanographic parameters from which environmental parameters predictive of species presence were identified through a series of mixed models. Ice cover and 10 kHz sound level were significant predictors of seal presence, with 40 kHz sound and prey presence (combined with ice cover) as potential predictors as well. Ice seal presence showed a strong positive correlation with ice cover and a negative association with 10 kHz environmental sound. On average, there was a 20-30 dB difference between sound levels during solid ice conditions compared to open water or melting conditions, providing a salient acoustic gradient between open water and solid ice conditions by which ice seals could orient. By constantly assessing the acoustic environment associated with the seasonal ice movement in the Bering Sea, it is possible that ice seals could utilize aspects of the soundscape to gauge their safe distance to open water or the ice edge by orienting in the direction of higher sound levels indicative of open water, especially in the frequency range above 1 kHz. In rapidly changing Arctic and sub-Arctic environments, the seasonal ice conditions and soundscapes are likely to change which may impact the ability of animals using ice presence and cues to successfully function during the winter breeding season.

  13. Environmental predictors of ice seal presence in the Bering Sea.

    Directory of Open Access Journals (Sweden)

    Jennifer L Miksis-Olds

    Full Text Available Ice seals overwintering in the Bering Sea are challenged with foraging, finding mates, and maintaining breathing holes in a dark and ice covered environment. Due to the difficulty of studying these species in their natural environment, very little is known about how the seals navigate under ice. Here we identify specific environmental parameters, including components of the ambient background sound, that are predictive of ice seal presence in the Bering Sea. Multi-year mooring deployments provided synoptic time series of acoustic and oceanographic parameters from which environmental parameters predictive of species presence were identified through a series of mixed models. Ice cover and 10 kHz sound level were significant predictors of seal presence, with 40 kHz sound and prey presence (combined with ice cover as potential predictors as well. Ice seal presence showed a strong positive correlation with ice cover and a negative association with 10 kHz environmental sound. On average, there was a 20-30 dB difference between sound levels during solid ice conditions compared to open water or melting conditions, providing a salient acoustic gradient between open water and solid ice conditions by which ice seals could orient. By constantly assessing the acoustic environment associated with the seasonal ice movement in the Bering Sea, it is possible that ice seals could utilize aspects of the soundscape to gauge their safe distance to open water or the ice edge by orienting in the direction of higher sound levels indicative of open water, especially in the frequency range above 1 kHz. In rapidly changing Arctic and sub-Arctic environments, the seasonal ice conditions and soundscapes are likely to change which may impact the ability of animals using ice presence and cues to successfully function during the winter breeding season.

  14. Carbon Dioxide Sealing Capacity: Textural or Compositional Controls?

    Energy Technology Data Exchange (ETDEWEB)

    Cranganu, Constantin; Soleymani, Hamidreza; Sadiqua, Soleymani; Watson, Kieva

    2013-11-30

    This research project is aiming to assess the carbon dioxide sealing capacity of most common seal-rocks, such as shales and non-fractured limestones, by analyzing the role of textural and compositional parameters of those rocks. We hypothesize that sealing capacity is controlled by textural and/or compositional pa-rameters of caprocks. In this research, we seek to evaluate the importance of textural and compositional parameters affecting the sealing capacity of caprocks. The conceptu-al framework involves two testable end-member hypotheses concerning the sealing ca-pacity of carbon dioxide reservoir caprocks. Better understanding of the elements controlling sealing quality will advance our knowledge regarding the sealing capacity of shales and carbonates. Due to relatively low permeability, shale and non-fractured carbonate units are considered relatively imper-meable formations which can retard reservoir fluid flow by forming high capillary pres-sure. Similarly, these unites can constitute reliable seals for carbon dioxide capture and sequestration purposes. This project is a part of the comprehensive project with the final aim of studying the caprock sealing properties and the relationship between microscopic and macroscopic characteristics of seal rocks in depleted gas fields of Oklahoma Pan-handle. Through this study we examined various seal rock characteristics to infer about their respective effects on sealing capacity in special case of replacing reservoir fluid with super critical carbon dioxide (scCO{sub 2}). To assess the effect of textural and compositional properties on scCO{sub 2} maximum reten-tion column height we collected 30 representative core samples in caprock formations in three counties (Cimarron, Texas, Beaver) in Oklahoma Panhandle. Core samples were collected from various seal formations (e.g., Cherokee, Keys, Morrowan) at different depths. We studied the compositional and textural properties of the core samples using several techniques

  15. Method and apparatus for detecting flaws and defects in heat seals

    Science.gov (United States)

    Rai, Kula R. (Inventor); Lew, Thomas M. (Inventor); Sinclair, Robert B. (Inventor)

    1993-01-01

    Flaws and defects in heat seals formed between sheets of translucent film are identified by optically examining consecutive lateral sections of the seal along the seal length. Each lateral seal section is illuminated and an optical sensor array detects the intensity of light transmitted through the seal section for the purpose of detecting and locating edges in the heat seal. A line profile for each consecutive seal section is derived having an amplitude proportional to the change in light intensity across the seal section. Instances in the derived line profile where the amplitude is greater than a threshold level indicate the detection of a seal edge. The detected edges in each derived line profile are then compared to a preset profile edge standard to identify the existence of a flaw or defect.

  16. Simulation Analysis of Spherical Mechanical Seal Property of Marine Stern Shaft

    Directory of Open Access Journals (Sweden)

    Zhou Xu Hui

    2016-01-01

    Full Text Available The finite element model of spherical mechanical seal wasestablished with ANSYS, and the influence of seawater pressure, shaft speed and other factors on the sealing performance was discussed. The study results show that local contact situation of the spherical mechanical seal is in the outside of the seal rings, and both maximum contact pressure and temperature appearat the same position. As sea water pressure and stern shaft rotary speed are increased, the contact pressure and temperature of the spherical seal surface are raised, and when the contact pressure of seal surface is 0, the spherical seal surface forms two zones including contact one and clearance zone. The former is near the outside of the seal ring, the lateris close to the inside of one. These research results are of important theoretical significance and engineering application value for the development of new kinds of mechanical seals, and improvement of both safety and survivability of underwater vehicles.

  17. Multiple internal seal ring micro-electro-mechanical system vacuum packaging method

    Science.gov (United States)

    Hayworth, Ken J. (Inventor); Yee, Karl Y. (Inventor); Shcheglov, Kirill V. (Inventor); Bae, Youngsam (Inventor); Wiberg, Dean V. (Inventor); Challoner, A. Dorian (Inventor); Peay, Chris S. (Inventor)

    2008-01-01

    A Multiple Internal Seal Ring (MISR) Micro-Electro-Mechanical System (MEMS) vacuum packaging method that hermetically seals MEMS devices using MISR. The method bonds a capping plate having metal seal rings to a base plate having metal seal rings by wafer bonding the capping plate wafer to the base plate wafer. Bulk electrodes may be used to provide conductive paths between the seal rings on the base plate and the capping plate. All seals are made using only metal-to-metal seal rings deposited on the polished surfaces of the base plate and capping plate wafers. However, multiple electrical feed-through metal traces are provided by fabricating via holes through the capping plate for electrical connection from the outside of the package through the via-holes to the inside of the package. Each metal seal ring serves the dual purposes of hermetic sealing and providing the electrical feed-through metal trace.

  18. Analysis of Mechanical Seals for High-Speed Centrifugal Gas Compressors

    Directory of Open Access Journals (Sweden)

    K.N. Nwaigwe

    2012-08-01

    Full Text Available A study aimed at seal selection efficiency for centrifugal pumps in the oil and gas industry is presented. A detailed analysis of mechanical seals in use in exploration and production activities of the oil and gas sector was undertaken. The approach of analysis was using seal design equations as mathematical models for simulating the performance of the mechanical seal. The results showed a mechanical seal with balance value of 0.5, an increased surface area between mating surfaces; provided with a flush system to enhance cooling and with seal face gap of 50 mm or less between the mating surfaces for minimal or zero leakage. The obtained results can aid the industries in seal selection and seal manufacturers in seal specifications.

  19. Metal Sealing Performance of Subsea X-tree Wellhead Connector Sealer

    Institute of Scientific and Technical Information of China (English)

    ZHAO Honglin; CHEN Rui; LUO Xiaolan; DUAN Menglan; LU Yinghui; FU Guowei; TIAN Hongping; YE Daohui

    2015-01-01

    The metal sealing performance of subsea X-tree wellhead connectors is crucial for the safety and reliability of subsea X-trees. In order to establish the theoretical relation between metal sealing ring’s contact stress and its structural parameters and working pressure, a mechanical analysis method for double-cone sealing of high pressure vessels is applied in analyzing the metal sealing ring under the condition of preload and operation. As a result, the formula of the unit sealing load for the metal sealing ring under operation with residual preload is shown in this paper, which ensures that the metal sealing ring has an excellent sealing effect and can prevent the metal sealing ring from yielding. Besides, while analyzing the sealing process of the metal sealing ring, the change rule of contact stress and working pressure is concluded here, putting forward that the structural parameters of the metal sealing ring are the major factors affecting the change rule. Finally, the analytical solution through theoretical analysis is compared with the simulation result through finite element analysis in a force feedback experiment, and both are consistent with each other, which fully verifies for the design and calculation theory on metal sealing ring’s contact stress and its structural parameters and working pressure deduced in this paper. The proposed research will be treated as an applicable theory guiding the design of metal seal for subsea X-tree wellhead connectors.

  20. Lab-on-a-Chip

    Science.gov (United States)

    2004-01-01

    Labs on chips are manufactured in many shapes and sizes and can be used for numerous applications, from medical tests to water quality monitoring to detecting the signatures of life on other planets. The eight holes on this chip are actually ports that can be filled with fluids or chemicals. Tiny valves control the chemical processes by mixing fluids that move in the tiny channels that look like lines, connecting the ports. Scientists at NASA's Marshall Space Flight Center (MSFC) in Huntsville, Alabama designed this chip to grow biological crystals on the International Space Station. Through this research, they discovered that this technology is ideally suited for solving the challenges of the Vision for Space Exploration. For example, thousands of chips the size of dimes could be loaded on a Martian rover looking for biosignatures of past or present life. Other types of chips could be placed in handheld devices used to monitor microbes in water or to quickly conduct medical tests on astronauts. (NASA/MSFC/D.Stoffer)

  1. Investigation of a Wedge Adhesion Test for Edge Seals

    Energy Technology Data Exchange (ETDEWEB)

    Kempe, Michael; Wohlgemuth, John; Miller, David; Postak, Lori; Booth, Dennis; Phillips, Nancy

    2016-09-26

    Many photovoltaic (PV) technologies have been found to be sensitive to moisture that diffuses into a PV package. Even with the use of impermeable frontsheets and backsheets, moisture can penetrate from the edges of a module. To limit this moisture ingress pathway from occurring, manufacturers often use a low permeability polyisobutylene (PIB) based edge seal filled with desiccant to further restrict moisture ingress. Moisture ingress studies have shown that these materials are capable of blocking moisture for the 25-year life of a module; but to do so, they must remain well-adhered and free of cracks. This work focuses on adapting the Boeing Wedge test for use with edge seals laminated using glass substrates as part of a strategy to assess the long-term durability of edge seals. The advantage of this method is that it duplicates the residual stresses and strains that a glass/glass module may have when the lamination process results in some residual glass bending that puts the perimeter in tension. Additionally, this method allows one to simultaneously expose the material to thermal stress, humidity, mechanical stress, and ultraviolet radiation. The disadvantage of this method generally is that we are limited by the fracture toughness of the glass substrates that the edge seal is adhered to. However, the low toughness of typical uncrosslinked or sparsely crosslinked PIB makes them suitable for this technique. We present data obtained during the development of the wedge test for use with PV edge seal materials. This includes development of the measuring techniques and evaluation of the test method with relevant materials. We find consistent data within a given experiment, along with the theoretical independence of fracture toughness measurements with wedge thickness. This indicates that the test methodology is reproducible. However, even though individual experimental sets are consistent, the reproducibility between experimental sets is poor. We believe this may be

  2. Investigation of a wedge adhesion test for edge seals

    Science.gov (United States)

    Kempe, Michael; Wohlgemuth, John; Miller, David; Postak, Lori; Booth, Dennis; Phillips, Nancy

    2016-09-01

    Many photovoltaic (PV) technologies have been found to be sensitive to moisture that diffuses into a PV package. Even with the use of impermeable frontsheets and backsheets, moisture can penetrate from the edges of a module. To limit this moisture ingress pathway from occurring, manufacturers often use a low permeability polyisobutylene (PIB) based edge seal filled with desiccant to further restrict moisture ingress. Moisture ingress studies have shown that these materials are capable of blocking moisture for the 25-year life of a module; but to do so, they must remain well-adhered and free of cracks. This work focuses on adapting the Boeing Wedge test for use with edge seals laminated using glass substrates as part of a strategy to assess the long-term durability of edge seals. The advantage of this method is that it duplicates the residual stresses and strains that a glass/glass module may have when the lamination process results in some residual glass bending that puts the perimeter in tension. Additionally, this method allows one to simultaneously expose the material to thermal stress, humidity, mechanical stress, and ultraviolet radiation. The disadvantage of this method generally is that we are limited by the fracture toughness of the glass substrates that the edge seal is adhered to. However, the low toughness of typical uncrosslinked or sparsely crosslinked PIB makes them suitable for this technique. We present data obtained during the development of the wedge test for use with PV edge seal materials. This includes development of the measuring techniques and evaluation of the test method with relevant materials. We find consistent data within a given experiment, along with the theoretical independence of fracture toughness measurements with wedge thickness. This indicates that the test methodology is reproducible. However, even though individual experimental sets are consistent, the reproducibility between experimental sets is poor. We believe this may be

  3. Seasonal activity budget of adult baltic ringed seals.

    Directory of Open Access Journals (Sweden)

    Tero Harkonen

    Full Text Available Although ringed seals are important components in oceanic and fresh water ecosystems at high latitudes, little is known about how they exploit these harsh environments. Seasonal activity and diving behaviour of 19 adult Baltic ringed seals were studied by satellite telemetry. We elaborated an activity budget for ten months of the year, extending over the period from moult to the breeding season. Seals from three main regions showed explicit site fidelity and the distributions of animals tagged from different areas did not overlap, suggesting separate stocks. Both the mean duration and the mean depth of dives peaked in June and July. Seals spent 70% (females to 85% (males of their time diving in June and July which decreased to 50% in late autumn. Less than one percent of dives exceeded 10 min in females, while 10% of male dives lasted longer than 10 min in June to September. Less than one percent of dives lasted for more than 25 min. Both females and males were most active during day time and hauled out predominantly during the night. Activity patterns during the summer are suggested to be correlated to energy accumulation and prey availability. The information on seasonal activity budget is crucial for developing population energetic models where interactions between ringed seals and other trophic levels can be evaluated.

  4. Effects of Geometry on Leakage Flow Characteristics of Brush Seal

    Institute of Scientific and Technical Information of China (English)

    Yuan Wei; Zhaobo Chen∗; Yinghou Jiao

    2015-01-01

    In order to better application of brush seal in rotating machinery, the leakage flow characteristics of the brush seal considering geometry effects are numerically analyzed using Reynolds⁃Averaged Navier⁃Stokes ( RANS) model coupling with a non⁃Darcian porous medium model. The reliability of the present numerical method is proved, which is in agreement with the experimental and numerical results from literatures. Three different bristle pack thicknesses, fence heights and initial clearances under different pressure ratios, rotational velocities and other operating conditions are utilized to investigate the effects of geometry modification on the brush seal leakage flow behaviors. It discusses the effectiveness of various geometry configurations outlining important flow features. The results indicate that the increase of fence height and clearance would lead to the increase of leakage rate. But the leakage is not linearly with respect to the bristle pack thickness, and the effect of rotational velocity is not obvious. Moreover, the detailed leakage flow fields and pressure distributions along the rotor surface, free bristle height, and fence height of the brush seals are also presented. The static pressure drop amplitude through the bristle pack and the pressure rise amplitude through the cavity would increase while the pressure differential increases. And the axial pressure is the main reason of bristle blow down. The results provide theoretical support for the brush seal structure optimal design.

  5. Harbour seals (Phoca vitulina) can steer by the stars.

    Science.gov (United States)

    Mauck, Björn; Gläser, Nele; Schlosser, Wolfhard; Dehnhardt, Guido

    2008-10-01

    Offshore orientation in marine mammals is still a mystery. For visual orientation during night-time foraging and travelling in the open seas, seals cannot rely on distant terrestrial landmarks, and thus might use celestial cues as repeatedly shown for nocturnally migrating birds. Although seals detect enough stars to probably allow for astronavigation, it was unclear whether they can orient by the night sky. The widely accepted cognitive mechanism for bird night-time orientation by celestial cues is a time-independent star compass with learned geometrical star configurations used to pinpoint north as the rotational centre of the starry sky while there is no conclusive evidence for a time-compensated star compass or true star navigation. Here, we present results for two harbour seals orienting in a custom made swimming planetarium. Both seals learned to highly accurately identify a lodestar out of a pseudo-randomly oriented, realistic projection of the northern hemisphere night sky. Providing the first evidence for star orientation capability in a marine mammal, our seals' outstanding directional precision would allow them to steer by following lodestars of learned star courses, a celestial orientation mechanism that has been known to be used by Polynesian navigators but has not been considered for animals yet.

  6. Status of harbour seals (Phoca vitulina in mainland Norway

    Directory of Open Access Journals (Sweden)

    Kjell Tormod Nilssen

    2010-09-01

    Full Text Available Harbour seals were counted along the entire Norwegian coast at known moulting haulout sites in the period mid-August to early September 2003-2006. In 2003-2005, almost all known moulting areas from Finnmark to Vestfold counties were covered by aerial photo surveys flown at altitudes of approximately 800-900 ft (243-274m, and at low tide (± 2 hours. Surveys in the Østfold County were flown in 2003-2006 at 300 ft (91m, and the small tidal amplitudes permitted counts to be carried out irrespective of the tidal cycle. In some sub-areas, two or three independent surveys were conducted. Visual counts using binoculars from smaller boats and islands were carried out in some selected areas. The surveys revealed a total minimum population of 6,705 harbour seals in Norwegian waters. Harbour seals were most abundant in the Nordland and Sør-Trøndelag counties with minimum estimates of approximately 2,500 and 1,500 seals, respectively. The presented minimum estimate is approximately 800 seals lower than an estimate obtained in a comparable study carried out during the moult in 1996-1999. Increased anthropogenic removals, and the phocine distemper virus (PDV epidemic in the Skagerrak region in 2002, may have contributed to the current lower estimate.

  7. Straight cylindrical seal for high-performance turbomachines

    Science.gov (United States)

    Hendricks, Robert C.

    1987-01-01

    A straight cylindrical seal configuration representing the seal for a high-performance turbopump (e.g., the space shuttle main engine fuel pump) was tested under static (nonrotating) conditions. The test data included critical mass flux and pressure profiles over a wide range of inlet temperatures and pressures for fluid nitrogen and fluid hydrogen with the seal in concentric and fully eccentric positions. The critical mass fluxes (or leakage rates) for the concentric and fully eccentric configurations were nearly the same when based on stagnation conditions upstream of the seal. The fully eccentric configuration pressure profiles of the gas and liquid were different. Further, the pressure differences between the maximum and the minimum clearance positions were highly dependent on the geometric conditions, the temperature, and the absolute pressure at both the inlet and the exit. The pressure differences were greatest in the inlet region. The results, although complex, tend to follow the corresponding-states principles for critical flows. Gaseous injection near the seal exit plane significantly altered the pressure profiles and could be used to control turbomachine instabilities.

  8. Epizootics in harbour seals (Phoca vitulina: clinical aspects

    Directory of Open Access Journals (Sweden)

    Ursula Siebert

    2010-09-01

    Full Text Available Epizootic diseases causing considerable mortality in harbour seal populations have mainly been reported from the waters of the United States and Europe. Such die-offs were largely attributable to viral infections. Several hundred individuals died from respiratory infections caused by Influenza A viruses at the coast of New England, USA, in 1979, 1980 and 1982. More than 53,000 harbour seals were killed in European waters by Phocine Distemper Virus (PDV, a morbillivirus,in two outbreaks in 1988 and 2002. For several other epizootics of smaller scale in the waters of the Atlantic and Pacific coast of the USA and, most recently, in Danish and Swedish waters in 2007 the causes remain unclear, although characteristic respiratory symptoms and interstitial pneumonia suspicious of viral etiology were detected as well as occasionally bacterial infections caused by Erysipelothrix rhusiopathiae and Pseudomonas aeruginosa. Mass mortalities caused by biotoxins, direct human interactions or changes in oceanographic conditions have so far not been described for harbour seals. However, high organochlorine loads detected in European harbour seal populations and suspected to impede immune functions, were considered an aggravating factor in the 1988 morbillivirus epizootic. Establishing supranational stranding networks is a key prerequisite for the detection of future unusual die-offs in marine mammals. Detailed post-mortem investigations of all organ systems are essential for targeted etiological studies towards the causes of mass mortalities in seals.

  9. Self-degradable Cementitious Sealing Materials

    Energy Technology Data Exchange (ETDEWEB)

    Sugama, T.; Butcher, T., Lance Brothers, Bour, D.

    2010-10-01

    A self-degradable alkali-activated cementitious material consisting of a sodium silicate activator, slag, Class C fly ash, and sodium carboxymethyl cellulose (CMC) additive was formulated as one dry mix component, and we evaluated its potential in laboratory for use as a temporary sealing material for Enhanced Geothermal System (EGS) wells. The self-degradation of alkali-activated cementitious material (AACM) occurred, when AACM heated at temperatures of {ge}200 C came in contact with water. We interpreted the mechanism of this water-initiated self-degradation as resulting from the in-situ exothermic reactions between the reactants yielded from the dissolution of the non-reacted or partially reacted sodium silicate activator and the thermal degradation of the CMC. The magnitude of self-degradation depended on the CMC content; its effective content in promoting degradation was {ge}0.7%. In contrast, no self-degradation was observed from CMC-modified Class G well cement. For 200 C-autoclaved AACMs without CMC, followed by heating at temperatures up to 300 C, they had a compressive strength ranging from 5982 to 4945 psi, which is {approx}3.5-fold higher than that of the commercial Class G well cement; the initial- and final-setting times of this AACM slurry at 85 C were {approx}60 and {approx}90 min. Two well-formed crystalline hydration phases, 1.1 nm tobermorite and calcium silicate hydrate (I), were responsible for developing this excellent high compressive strength. Although CMC is an attractive, as a degradation-promoting additive, its addition to both the AACM and the Class G well cement altered some properties of original cementitious materials; among those were an extending their setting times, an increasing their porosity, and lowering their compressive strength. Nevertheless, a 0.7% CMC-modified AACM as self-degradable cementitious material displayed the following properties before its breakdown by water; {approx}120 min initial- and {approx}180 min final

  10. Influenza A(H10N7) Virus in Dead Harbor Seals, Denmark

    DEFF Research Database (Denmark)

    Krog, Jesper Schak; Hansen, Mette Sif; Holm, Elisabeth

    2015-01-01

    Since April 2014, an outbreak of influenza in harbor seals has been ongoing in northern Europe. In Denmark during June-August, 152 harbor seals on the island of Anholt were found dead from severe pneumonia. We detected influenza A(H10N7) virus in 2 of 4 seals examined.......Since April 2014, an outbreak of influenza in harbor seals has been ongoing in northern Europe. In Denmark during June-August, 152 harbor seals on the island of Anholt were found dead from severe pneumonia. We detected influenza A(H10N7) virus in 2 of 4 seals examined....

  11. Behavior of primary coolant pump shaft seals during station blackout conditions

    Energy Technology Data Exchange (ETDEWEB)

    Hill, R.C.; Rhodes, D.B.

    1986-09-12

    An assessment is made of the ability of typical Reactor Coolant Pump (RCP) Shaft Seals to withstand the conditions predicted for a station blackout (loss of all alternating current power) at a nuclear power station. Several factors are identified that are key to seal stability including inlet fluid conditions, pressure downstream of the seal, and geometrical details of the seal rings. Limits for stable seal operation are determined for various combinations of these factors, and the conclusion is drawn that some RPC seals would be near the threshold of instability during a station blackout. If the threshold were exceeded, significant leakage of coolant from the primary coolant system could be expected.

  12. Parameters important to reactor coolant pump seal stability during station blackout

    Energy Technology Data Exchange (ETDEWEB)

    Hill, R.C.; Rhodes, D.B.

    1986-10-24

    An assessment is made of the ability of typical Reactor Coolant Pump (RCP) Shaft Seals to withstand the conditions predicted for a station blackout (loss of all alternating current power) at a nuclear power station. Several factors are identified that are key to seal stability including inlet fluid conditions, pressure downstream of the seal, and geometrical details of the seal rings. Limits for stable seal operation are determined for various combinations of these factors, and the conclusion is drawn that some RPC seals would be near or over the threshold of instability during a station blackout. If the threshold were exceeded, significant leakage of coolant from the primary coolant system could be expected.

  13. ANALYSIS OF COUPLING INFLUENCES OF LABYRINTH SEAL PARAMETERS ON CROSS COUPLED STIFFNESS AND DIRECT DAMPING COEFFICIENT

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Labyrinth seal can cause steamexciting,the structural and operating parameters of labyrinth seal have effect on stability of rotorsystem.For investigating the coupling influences of the structure and operating parameters of labyrinth seals on dynamic coefficients,a model of calculating dynamic coefficients of labyrinth seals is presented using a two control volume model.The coupling influences of parameters on crosscoupled stiffness and direct damping of labyrinth seal are discussed.In the conclusion,a reference of pre venting steamexciting vibration and optimum determination of design parameters of labyrinth seals are provided.

  14. ELISE NMR: Experimental liquid sealing of NMR samples

    Science.gov (United States)

    Wieruszeski, Jean-Michel; Landrieu, Isabelle; Hanoulle, Xavier; Lippens, Guy

    2006-08-01

    We present a simple, generally applicable approach to prevent sample evaporation when working at elevated temperatures in high resolution NMR. It consists of experimentally sealing the NMR sample by a second liquid (Experimental Liquid Sealing, ELISE). For aqueous samples, we identified the mineral oil commonly used in PCR application as the best candidate, because it contains only a very limited amount of water-soluble contaminants, is stable over time and heat resistant. The procedure does not interfere with shim settings, and is compatible with a wide variety of samples, including oligosaccharides and proteins. For chloroform samples, a simple drop of water allows to efficiently seal the sample, avoiding solvent evaporation even over lengthy time periods.

  15. Simulation of the noise transmission through automotive door seals

    CERN Document Server

    Hazir, Andreas

    2016-01-01

    Andreas Hazir is investigating the door seal contribution to the interior noise level of production vehicles. These investigations contain experimental contribution analyses of real production vehicles and of academic test cases as well as the development of a simulation methodology for noise transmission through sealing systems and side windows. The simulations are realized by coupling transient computational aeroacoustics of the exterior flow to nonlinear finite element simulations of the structural transmission. By introducing a linear transmission model, the setup and computational costs of the seal noise transmission are significantly reduced, resulting in the feasibility of numerical contribution analyses of real production vehicles. Contents Contribution Analyses of Production Vehicles Acoustic Excitation versus Aeroacoustic Excitation Development of a Simulation Methodology Sensitivity Analysis of Noise Transmission Simulations Target Groups Researchers and students in the field of automotive engineer...

  16. Phocine distemper virus in seals, east coast, United States, 2006.

    Science.gov (United States)

    Philip Earle, J A; Melia, Mary M; Doherty, Nadine V; Nielsen, Ole; Cosby, S Louise

    2011-02-01

    In 2006 and 2007, elevated numbers of deaths among seals, constituting an unusual mortality event, occurred off the coasts of Maine and Massachusetts, United States. We isolated a virus from seal tissue and confirmed it as phocine distemper virus (PDV). We compared the viral hemagglutinin, phosphoprotein, and fusion (F) and matrix (M) protein gene sequences with those of viruses from the 1988 and 2002 PDV epizootics. The virus showed highest similarity with a PDV 1988 Netherlands virus, which raises the possibility that the 2006 isolate from the United States might have emerged independently from 2002 PDVs and that multiple lineages of PDV might be circulating among enzootically infected North American seals. Evidence from comparison of sequences derived from different tissues suggested that mutations in the F and M genes occur in brain tissue that are not present in lung, liver, or blood, which suggests virus persistence in the central nervous system.

  17. Infrared laser sealing of porcine tissues: preliminary in vivo studies

    Science.gov (United States)

    Cilip, Christopher M.; Hutchens, Thomas C.; Kerr, Duane; Latimer, Cassandra; Rosenbury, Sarah B.; Giglio, Nicholas C.; Schweinsberger, Gino R.; Perkins, William C.; Wilson, Christopher R.; Ward, Arlen; Nau, William H.; Fried, Nathaniel M.

    2015-02-01

    We are exploring infrared (IR) lasers as an alternative energy modality to radiofrequency (RF) and ultrasonic (US) devices intended to provide rapid surgical hemostasis with minimal collateral zones of thermal damage and tissue necrosis. Previously, a 1470-nm IR laser sealed and cut ex vivo porcine renal arteries of 1-8 mm in 2 s, yielding burst pressures porcine model. A prototype, fiber optic based handheld probe with vessel/tissue clasping mechanism was tested on blood vessels Collagen denaturation averaged 1.6 mm in 8 samples excised for histologic examination. A handheld laser probe sealed porcine vessels in vivo. With further improvements in probe design and laser parameter optimization, IR lasers may provide an alternative to RF and US vessel sealing devices.

  18. New-Generation Sealing Slurries For Borehole Injection Purposes

    Science.gov (United States)

    Stryczek, Stanisław; Gonet, Andrzej; Wiśniowski, Rafał; Złotkowski, Albert

    2015-12-01

    The development of techniques and technologies thanks to which parameters of the ground medium can be modified makes specialists look for new recipes of geopolymers - binders for the reinforcing and sealing of unstable and permeable grounds. The sealing slurries are expected to meet a number of strict requirements, therefore it is important to find new admixtures and additives which could modify the fresh and hardened slurry. Special attention has been recently paid to the fluid ash - a by-product of the combustion of hard coals. However, the use of this additive is associated with the application of appropriate superplastifier. Laboratory analyses of rheological parameters of fresh sealing slurries and the ways of improving their liquidity by a properly selected third-generation superplastifier are presented in the paper. The slurries were based on Portland cement CEM I, milled granulated large-furnace slag and fly ash from fluidized-bed combustion of hard coal.

  19. Research on security vulnerability of chip

    Science.gov (United States)

    Chen, Zhifeng; Li, Qingbao; Li, Zhou

    2013-03-01

    The 21st century is the information era. IC (Integrated Circuit) is the basis of the modern information industry. The security vulnerability or back door of IC is directly related to the entire information system security. From the perspective of information security, security vulnerability of chip is led out through the practical examples and then the importance of security vulnerability of chip is emphasized. By comparing the security vulnerability of chip with the software virus, the characteristics of the chip vulnerabilities are summed up. Moreover, this paper describes the security vulnerability models of different control logic chips, combinational and sequential logic chips models. Finally it puts forward two kinds of detecting methods of security vulnerability of chip against the two models.

  20. Chip Advancer For GPS Receiver

    Science.gov (United States)

    Meehan, Thomas K.; Srinivasan, Jeffrey M.; Thomas, J. Brooks

    1989-01-01

    Instrument errors made negligible. For each integration interval, both delay and rate of change of delay initialized to small fraction of chip - for example, to order of 10 to the negative 7th power - thereby making feedback control and extraction of delay highly accurate and flexible. With appropriate selection of sampling rate relative to chip rate, commensurability errors reduced to extremely small levels. In Global Positioning System (GPS) receiver, pseudorandom code sequence generated by simple digital logic incorporating effects of time, delay, and rate of change of delay. Flexibility in starting time and sum interval very useful in aligning correlation interval with beginnings and endings of data bits.

  1. Experiment list: SRX122465 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available 6 || chip antibody=Relb || treatment=LPS || time=120 min || chip antibody manufacturer 1=Bethyl || chip anti...body catalog number 1=A302-183A || chip antibody manufacturer 2=Santa Cruz || chip antibody catalog number 2

  2. Experiment list: SRX122555 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available chip antibody=Stat1 || treatment=LPS || time=120 min || chip antibody manufacturer 1=Santa Cruz || chip anti...body catalog number 1=sc-346 || chip antibody manufacturer 2=Bethyl || chip antibody catalog number 2=A302-7

  3. Experiment list: SRX122556 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available chip antibody=Stat1 || treatment=LPS || time=120 min || chip antibody manufacturer 1=Santa Cruz || chip anti...body catalog number 1=sc-346 || chip antibody manufacturer 2=Bethyl || chip antibody catalog number 2=A302-7

  4. Nanophotonic lab-on-a-chip platforms including novel bimodal interferometers, microfluidics and grating couplers.

    Science.gov (United States)

    Duval, Daphné; González-Guerrero, Ana Belén; Dante, Stefania; Osmond, Johann; Monge, Rosa; Fernández, Luis J; Zinoviev, Kirill E; Domínguez, Carlos; Lechuga, Laura M

    2012-05-08

    One of the main limitations for achieving truly lab-on-a-chip (LOC) devices for point-of-care diagnosis is the incorporation of the "on-chip" detection. Indeed, most of the state-of-the-art LOC devices usually require complex read-out instrumentation, losing the main advantages of portability and simplicity. In this context, we present our last advances towards the achievement of a portable and label-free LOC platform with highly sensitive "on-chip" detection by using nanophotonic biosensors. Bimodal waveguide interferometers fabricated by standard silicon processes have been integrated with sub-micronic grating couplers for efficient light in-coupling, showing a phase resolution of 6.6 × 10(-4)× 2π rad and a limit of detection of 3.3 × 10(-7) refractive index unit (RIU) in bulk. A 3D network of SU-8 polymer microfluidics monolithically assembled at the wafer-level was included, ensuring perfect sealing and compact packaging. To overcome some of the drawbacks inherent to interferometric read-outs, a novel all-optical wavelength modulation system has been implemented, providing a linear response and a direct read-out of the phase variation. Sensitivity, specificity and reproducibility of the wavelength modulated BiMW sensor has been demonstrated through the label-free immunodetection of the human hormone hTSH at picomolar level using a reliable biofunctionalization process.

  5. Consistency and sealing of advanced bipolar tissue sealers

    Directory of Open Access Journals (Sweden)

    Chekan EG

    2015-04-01

    Full Text Available Edward G Chekan , Mark A Davison, David W Singleton, John Z Mennone, Piet Hinoul Ethicon, Inc., Cincinnati, OH, USA Objectives: The aim of this study was to evaluate two commonly used advanced bipolar devices (ENSEAL® G2 Tissue Sealers and LigaSure™ Blunt Tip for compression uniformity, vessel sealing strength, and consistency in bench-top analyses. Methods: Compression analysis was performed with a foam pad/sensor apparatus inserted between closed jaws of the instruments. Average pressures (psi were recorded across the entire inside surface of the jaws, and over the distal one-third of jaws. To test vessel sealing strength, ex vivo pig carotid arteries were sealed and transected and left and right (sealed halves of vessels were subjected to burst pressure testing. The maximum bursting pressures of each half of vessels were averaged to obtain single data points for analysis. The absence or presence of tissue sticking to device jaws was noted for each transected vessel. Results: Statistically higher average compression values were found for ENSEAL® instruments (curved jaw and straight jaw compared to LigaSure™, P<0.05. Moreover, the ENSEAL® devices retained full compression at the distal end of jaws. Significantly higher and more consistent median burst pressures were noted for ENSEAL® devices relative to LigaSure™ through 52 firings of each device (P<0.05. LigaSure™ showed a significant reduction in median burst pressure for the final three firings (cycles 50–52 versus the first three firings (cycles 1–3, P=0.027. Tissue sticking was noted for 1.39% and 13.3% of vessels transected with ENSEAL® and LigaSure™, respectively. Conclusion: In bench-top testing, ENSEAL® G2 sealers produced more uniform compression, stronger and more consistent vessel sealing, and reduced tissue sticking relative to LigaSure™. Keywords: ENSEAL, sealing, burst pressure, laparoscopic, compression, LigaSure

  6. Randomized controlled trial of sealed in-office bleaching effectiveness.

    Science.gov (United States)

    Santana, Mário Artur Pereira; Nahsan, Flávia Pardo Salata; Oliveira, Alaíde Hermínia de Aguiar; Loguércio, Alessandro Dourado; Faria-e-Silva, André Luis

    2014-01-01

    Regardless of the high success rate, patients commonly report the occurrence of tooth sensitivity during the in-office bleaching procedures. Recently, it has been demonstrated that using a customized tray (called sealed in-office bleaching technique) reduces peroxide penetration. The aim of this randomized clinical study was to evaluate tooth sensitivity and bleaching efficacy of sealed bleaching, in comparison with a conventional in-office technique. Twenty patients were randomized allocated in two groups in which 35% hydrogen peroxide gel was used in a single 45-min application. For the sealed technique, a customized bleaching tray was fabricated and carefully positioned over the bleaching agent during the session. The color was recorded at a baseline, 7 and 28 days after the bleaching session, using Vita Easy Shade spectrophotometer. Tooth sensitivity was recorded during (20 and 40 min) and immediately after the treatment using a visual analogue scale. The bleaching efficacy was evaluated by repeated-measures ANOVA, while the absolute risk of tooth sensitivity and its intensity were evaluated by Fisher's exact and Mann-Whitney tests, respectively (α=0.05). No significant difference on bleaching efficacy was observed between the conventional (7.4 and 8.1 ΔE) and sealed techniques (7.8 and 8.3 ΔE) at both evaluation periods. No significant difference was observed regarding the absolute risk of tooth sensitivity (p=0.15). Sealed technique showed a significant decrease of sensitivity intensity after 40 min (p=0.03). Sealed bleaching technique was able to reduce the sensitivity intensity during the bleaching procedure, without jeopardizing the bleaching efficacy.

  7. Numerical solution of a flow inside a labyrinth seal

    Directory of Open Access Journals (Sweden)

    Šimák Jan

    2012-04-01

    Full Text Available The aim of this study is a behaviour of a flow inside a labyrinth seal on a rotating shaft. The labyrinth seal is a type of a non-contact seal where a leakage of a fluid is prevented by a rather complicated path, which the fluid has to overcome. In the presented case the sealed medium is the air and the seal is made by a system of 20 teeth on a rotating shaft situated against a smooth static surface. Centrifugal forces present due to the rotation of the shaft create vortices in each chamber and thus dissipate the axial velocity of the escaping air.The structure of the flow field inside the seal is studied through the use of numerical methods. Three-dimensional solution of the Navier-Stokes equations for turbulent flow is very time consuming. In order to reduce the computational time we can simplify our problem and solve it as an axisymmetric problem in a two-dimensional meridian plane. For this case we use a transformation of the Navier-Stokes equations and of the standard k-omega turbulence model into a cylindrical coordinate system. A finite volume method is used for the solution of the resulting problem. A one-side modification of the Riemann problem for boundary conditions is used at the inlet and at the outlet of the axisymmetric channel. The total pressure and total density (temperature are to be used preferably at the inlet whereas the static pressure is used at the outlet for the compatibility. This idea yields physically relevant boundary conditions. The important characteristics such as a mass flow rate and a power loss, depending on a pressure ratio (1.1 - 4 and an angular velocity (1000 - 15000 rpm are evaluated.

  8. End of Life Decisions for Sealed Radioactive Sources

    Energy Technology Data Exchange (ETDEWEB)

    Pryor, Kathryn H.

    2016-02-29

    Sealed radioactive sources are encountered in a wide variety of settings – from household smoke detectors and instrument check sources, through fixed industrial gauges, industrial radiography and well logging sources, to irradiators and medical teletherapy devices. In general, the higher the level of activity in the sealed source, the stricter the regulatory control that is applied to its use, control and ultimate disposition. Lower levels of attention and oversight can and do lead to sources ending up in the wrong place – as orphan sources in uncontrolled storage, disposed in a sanitary landfill, melted down in metal recycling operations and incorporated into consumer products, or handled by an unsuspecting member of the public. There are a range of issues that contribute to the problem of improper disposal of sealed sources, and, in particular, to disused source disposal. General licensed sources and devices are particularly at risk of being disposed incorrectly. Higher activity general licensed sources, although required to be registered with the Nuclear Regulatory Commission (NRC) or Agreement State, receive limited regulatory oversight and are not tracked on a national scale. Users frequently do not consider the full life-cycle costs when procuring sources or devices and discover that they cannot afford to package, transport and dispose of their sources properly. The NRC requirements for decommissioning funding plans and financial assurance are not adequate to cover sealed source transport and disposal costs fully. While there are regulatory limits for storage of disused sources, enforcement is limited and there is no financial incentive for owners to dispose of the sources. In some cases, the lack of availability of approved Department of Transportation (DOT) Type B shipping casks also presents a barrier to sealed source disposal. The report of the Disused Sources Working Group does an excellent job of framing these issues. This article reviews both the

  9. Development of braided rope seals for hypersonic engine applications: Flow modeling

    Science.gov (United States)

    Mutharasan, Rajakkannu; Steinetz, Bruce M.; Tao, Xiaoming; Du, Guang-Wu; Ko, Frank

    1992-12-01

    A new type of engine seal is being developed to meet the needs of advanced hypersonic engines. A seal braided of emerging high temperature ceramic fibers comprised of a sheath-core construction was selected for study based on its low leakage rates. Flexible, low-leakage, high temperature seals are required to seal the movable engine panels of advanced ramjet-scramjet engines either preventing potentially dangerous leakage into backside engine cavities or limiting the purge coolant flow rates through the seals. To predict the leakage through these flexible, porous seal structures new analytical flow models are required. Two such models based on the Kozeny-Carman equations are developed herein and are compared to experimental leakage measurements for simulated pressure and seal gap conditions. The models developed allow prediction of the gas leakage rate as a function of fiber diameter, fiber packing density, gas properties, and pressure drop across the seal. The first model treats the seal as a homogeneous fiber bed. The second model divides the seal into two homogeneous fiber beds identified as the core and the sheath of the seal. Flow resistances of each of the main seal elements are combined to determine the total flow resistance. Comparisons between measured leakage rates and model predictions for seal structures covering a wide range of braid architectures show good agreement. Within the experimental range, the second model provides a prediction within 6 to 13 percent of the flow for many of the cases examined. Areas where future model refinements are required are identified.

  10. Predicting the Performance of Edge Seal Materials for PV (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Kempe, M.; Panchagade, D.; Dameron, A.; Reese, M.

    2012-03-01

    Edge seal materials were evaluated using a 100-nm film of Ca deposited on glass and laminated to another glass substrate. As moisture penetrates the package it converts the Ca metal to transparent CaOH2 giving a clear indication of the depth to which moisture has entered. Using this method, we have exposed test samples to a variety of temperature and humidity conditions ranging from 45C and 10% RH up to 85C and 85% RH, to ultraviolet radiation and to mechanical stress. We are able to show that edge seal materials are capable of keeping moisture away from sensitive cell materials for the life of a module.

  11. Leaf seal for transition duct in turbine system

    Science.gov (United States)

    Flanagan, James Scott; LeBegue, Jeffrey Scott; McMahan, Kevin Weston; Dillard, Daniel Jackson; Pentecost, Ronnie Ray

    2013-06-11

    A turbine system is disclosed. In one embodiment, the turbine system includes a transition duct. The transition duct includes an inlet, an outlet, and a passage extending between the inlet and the outlet and defining a longitudinal axis, a radial axis, and a tangential axis. The outlet of the transition duct is offset from the inlet along the longitudinal axis and the tangential axis. The transition duct further includes an interface member for interfacing with a turbine section. The turbine system further includes a leaf seal contacting the interface member to provide a seal between the interface member and the turbine section.

  12. Effects of Low Earth Orbit on Docking Seal Materials

    Science.gov (United States)

    Imka, Emily C.; Asmar, Olivia C.; deGroh, Henry C., III; Banks, Bruce A.

    2014-01-01

    Spacecraft docking seals are typically made of silicone elastomers. When such seals are exposed to low Earth orbit (LEO) conditions, they can suffer damage from ultraviolet (UV) radiation and atomic oxygen (AO, or monoatomic oxygen, the predominant oxygen species in LEO). An experiment flew on the International Space Station (ISS) to measure the effects of LEO on seal materials S0383-70 and ELA-SA-401 and various mating counterface materials which included anodized aluminum. Samples flown in different orientations received different amounts of UV and AO. The hypotheses were that most of the damage would be from UV, and 10 days or more of exposure in LEO would badly damage the seals. Eighteen seals were exposed for 543 days in ram (windward), zenith (away from Earth), or wake (leeward) orientations, and 15 control samples (not flown) provided undamaged baseline leakage. To determine post-flight leak rates, each of the 33 seals were placed in an O-ring groove of a leak test fixture and pressure tested over time. Resistance temperature detectors (RTDs), pressure transducers, and LabVIEW (National Instruments) programs were used to measure and analyze the temperature and pressure and calculate leakage. Average leakage of control samples was 2.6 x 10(exp -7) lbs/day. LEO exposure did not considerably damage ELA-SA-401. The S0383-70 flight samples leaked at least 10 times more than ELA-SA-401 in all cases except one, demonstrating that ELA-SA-401 may be a more suitable sealing material in LEO. AO caused greater damage than UV; samples in ram orientation (receiving an AO fluence of 4.3 x 10(exp 21) atoms/(sq cm) and in wake (2.9x 10(exp 20) atoms/(sq cm)) leaked more than those in zenith orientation (1.58 x 10(exp 20) atoms/(sq cm)), whereas variations in UV exposure did not seem to affect the samples. Exposure to LEO did less damage to the seals than hypothesized, and the data did not support the conjecture that UV causes more damage than AO.

  13. Convolution seal for transition duct in turbine system

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, James Scott; LeBegue, Jeffrey Scott; McMahan, Kevin Weston; Dillard, Daniel Jackson; Pentecost, Ronnie Ray

    2015-03-10

    A turbine system is disclosed. In one embodiment, the turbine system includes a transition duct. The transition duct includes an inlet, an outlet, and a passage extending between the inlet and the outlet and defining a longitudinal axis, a radial axis, and a tangential axis. The outlet of the transition duct is offset from the inlet along the longitudinal axis and the tangential axis. The transition duct further includes an interface member for interfacing with a turbine section. The turbine system further includes a convolution seal contacting the interface member to provide a seal between the interface member and the turbine section.

  14. Convolution seal for transition duct in turbine system

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, James Scott; LeBegue, Jeffrey Scott; McMahan, Kevin Weston; Dillard, Daniel Jackson; Pentecost, Ronnie Ray

    2015-05-26

    A turbine system is disclosed. In one embodiment, the turbine system includes a transition duct. The transition duct includes an inlet, an outlet, and a passage extending between the inlet and the outlet and defining a longitudinal axis, a radial axis, and a tangential axis. The outlet of the transition duct is offset from the inlet along the longitudinal axis and the tangential axis. The transition duct further includes an interface feature for interfacing with an adjacent transition duct. The turbine system further includes a convolution seal contacting the interface feature to provide a seal between the interface feature and the adjacent transition duct.

  15. Sealed all-metal CO2 laser tube technology

    Science.gov (United States)

    Byron, Stanley; Laakmann, Peter

    A newly developed RF plasma configuration for CO2 lasers is described, that offers high performance at low cost, using an all-metal, sealed-off laser tube design. The plasma bore of 5-mm square cross section supports a free-space TEM(00) optical model and a laser power density 1/3 that of CO2 waveguide lasers, allowing fabrication of compact sealed-off CO2 lasers from 10 to 100 watts with good optical and mechanical integrity. Design and manufacturing factors are discussed that affect gas life, beam quality, modulation, optical stability, and cost.

  16. Could seals prevent cod recovery in the Baltic Sea?

    DEFF Research Database (Denmark)

    MacKenzie, Brian; Eero, Margit; Ojaveer, Henn

    2011-01-01

    Fish populations are increasingly affected by multiple human and natural impacts including exploitation, eutrophication, habitat alteration and climate change. As a result many collapsed populations may have to recover in ecosystems whose structure and functioning differ from those in which...... in an ecosystem that likely will change due to both the already started recovery of a cod predator, the grey seal Halichoerus grypus, and projected climate impacts. Simulation modelling, assuming increased seal predation, fishing levels consistent with management plan targets and stable salinity, shows...... these goals will also depend on how climate change affects cod recruitment....

  17. Vacuum sealing and cooling as methods to preserve surgical specimens

    DEFF Research Database (Denmark)

    Kielsgaard Kristensen, Thomas; Engvad, Birte; Nielsen, Ole;

    2011-01-01

    Recently, vacuum-based preservation of surgical specimens has been proposed as a safe alternative to formalin fixation at the surgical theater. The method seems feasible from a practical point of view, but no systematic study has examined the effect of vacuum sealing alone with respect to tissue...... effect of vacuum sealing was observed with respect to cellular morphology, detection of immunohistochemical epitopes, or RNA integrity. In contrast, storage at 4°C was shown to preserve tissue to a higher degree than storage at room temperature for all included endpoints, independently of whether...

  18. Sealing and External Sterilization of a Sample Container

    Science.gov (United States)

    Bar-Cohen, Yoseph; Badescu, Mircea; Bao, Xiaoqi; Sherrit, Stewart; Olorunsola, Ayoola

    2008-01-01

    A method of (1) sealing a sample of material acquired in a possibly b iologically contaminated ("dirty") environment into a hermetic conta iner, (2) sterilizing the outer surface of the container, then (3) d elivering the sealed container to a clean environment has been propos ed. The method now proposed was originally intended to be used to ret urn samples from Mars to Earth, but could also be used on Earth to t ransport material samples acquired in environments that contain biol ogical hazards and/or, in some cases, chemical hazards.

  19. The Measurement and Prediction of Rotordynamic Forces for Labyrinth Seals

    Science.gov (United States)

    1988-03-01

    AFOSRlM- 88-0 662 C-" DTIC FILE COPy THE MEASUREMENT AND PREDICTION OF I ROTORDYNAMIC FORCES FOR . ,LABYRINTH SEALS prepared by D. W. Childs D. L...FRMorcesT123/ 18, MARCH k 7~ 1 A 19. ABSTRACT ICniu IT JECTr TRM necesoary ond identif if R&iocftr an um rbyblckn %I I _I Measurements of rotordynamic ...0 FORM 1472, 83 APR EOITiC’q OF I iA 71 15 )SOLETF O~p - ...... 0 THE MEASUREMENT AND PREDICTION OF ROTORDYNAMIC FORCES FOR LABYRINTH SEALS prepared

  20. Atom chip gravimeter

    Science.gov (United States)

    Schubert, Christian; Abend, Sven; Gebbe, Martina; Gersemann, Matthias; Ahlers, Holger; Müntinga, Hauke; Matthias, Jonas; Sahelgozin, Maral; Herr, Waldemar; Lämmerzahl, Claus; Ertmer, Wolfgang; Rasel, Ernst

    2016-04-01

    Atom interferometry has developed into a tool for measuring rotations [1], accelerations [2], and testing fundamental physics [3]. Gravimeters based on laser cooled atoms demonstrated residual uncertainties of few microgal [2,4] and were simplified for field applications [5]. Atomic gravimeters rely on the interference of matter waves which are coherently manipulated by laser light fields. The latter can be interpreted as rulers to which the position of the atoms is compared. At three points in time separated by a free evolution, the light fields are pulsed onto the atoms. First, a coherent superposition of two momentum states is produced, then the momentum is inverted, and finally the two trajectories are recombined. Depending on the acceleration the atoms experienced, the number of atoms detected in the output ports will change. Consequently, the acceleration can be determined from the output signal. The laser cooled atoms with microkelvin temperatures used in state-of-the-art gravimeters impose limits on the accuracy [4]. Therefore, ultra-cold atoms generated by Bose-Einstein condensation and delta-kick collimation [6,7] are expected to be the key for further improvements. These sources suffered from a low flux implying an incompatible noise floor, but a competitive performance was demonstrated recently with atom chips [8]. In the compact and robust setup constructed for operation in the drop tower [6] we demonstrated all steps necessary for an atom chip gravimeter with Bose-Einstein condensates in a ground based operation. We will discuss the principle of operation, the current performance, and the perspectives to supersede the state of the art. The authors thank the QUANTUS cooperation for contributions to the drop tower project in the earlier stages. This work is supported by the German Space Agency (DLR) with funds provided by the Federal Ministry for Economic Affairs and Energy (BMWi) due to an enactment of the German Bundestag under grant numbers DLR 50WM

  1. Portable, Easy-to-Operate, and Antifouling Microcapsule Array Chips Fabricated by 3D Ice Printing for Visual Target Detection.

    Science.gov (United States)

    Zhang, Hong-Ze; Zhang, Fang-Ting; Zhang, Xiao-Hui; Huang, Dong; Zhou, Ying-Lin; Li, Zhi-Hong; Zhang, Xin-Xiang

    2015-06-16

    Herein, we proposed a portable, easy-to-operate, and antifouling microcapsule array chip for target detection. This prepackaged chip was fabricated by innovative and cost-effective 3D ice printing integrating with photopolymerization sealing which could eliminate complicated preparation of wet chemistry and effectively resist outside contaminants. Only a small volume of sample (2 μL for each microcapsule) was consumed to fulfill the assay. All the reagents required for the analysis were stored in ice form within the microcapsule before use, which guaranteed the long-term stability of microcapsule array chips. Nitrite and glucose were chosen as models for proof of concept to achieve an instant quantitative detection by naked eyes without the need of external sophisticated instruments. The simplicity, low cost, and small sample consumption endowed ice-printing microcapsule array chips with potential commercial value in the fields of on-site environmental monitoring, medical diagnostics, and rapid high-throughput point-of-care quantitative assay.

  2. Seal harvest in the United States and Canada: A selection of pertinent materials

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — The clubbing of fur seals in Alaska and the killing of baby harp seals in Canada currently are generating numerous requests for information. This compilation of...

  3. Aerial Survey Counts of Harbor Seals in Coastal Alaska (2003-2011)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This dataset supports efforts to estimate the abundance and trends in population size of Alaska harbor seals. Annual surveys of harbor seal populations are...

  4. HMSRP Hawaiian Monk Seal Island/Sector Locations for Data Collection

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This data set documents locations and location codes used in monk seal data collection as part of the ongoing monk seal population assessment efforts. Information...

  5. Electrosurgical bipolar vessel sealing versus conventional clamping and suturing for total abdominal hysterectomy: a randomized trial.

    NARCIS (Netherlands)

    Lakeman, M.; Kruitwagen, R.F.P.M.; Vos, M.C.; Roovers, J.P.

    2008-01-01

    STUDY OBJECTIVE: To compare the effects of bipolar vessel sealing versus conventional clamping and suturing in women undergoing total abdominal hysterectomy. DESIGN: A randomized controlled trial was performed. Patients were randomized to vessel sealing or conventional surgery. Postoperative pain wa

  6. Development of Hermetic Sealing Glasses for Solid Oxide Fuel Cells Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Sealing glasses, either rigid glass-ceramics or viscous, non-crystallizing compositions, will be developed and sealing processes will be optimized based on NASA's...

  7. Engineering report. Part 1: NASA wheel air seal development for space shuttle type environmental requirements

    Science.gov (United States)

    1973-01-01

    The sealing techniques are studied for existing aircraft wheel-tire designs to meet the hard vacuum .00001 torr and cold temperature -65 F requirements of space travel. The investigation covers the use of existing wheel seal designs.

  8. Control and optimization of sealing layer in films

    Science.gov (United States)

    Najarzadeh, Zahra

    Heat sealing is the process to achieve the hermetic closure of a package by applying heat and pressure on two polymer films for a specified dwell time. The heat sealing process has been used in packaging of a wide spectrum of products, in particular for food packaging. During the past two decades, heat sealing machinery has been developed for very high speed line production which requires very precise process condition and material optimization. Heat seal process conditions, including temperature, dwell time, and pressure as well as film characteristics such as molecular weight, molecular weight distribution, long and short chain branching are the key factors that control the final quality of the joint. In the first part of this study, we have investigated the interrelated influence of heat seal process parameters on the strengthening of the interface as well as the micro mechanisms involved. The effects of heat seal temperature, pressure, and dwell time on seal strength of LLDPE were illustrated in "time-temperature" and "pressure-temperature" 3D maps, a methodology that is easily applicable to other systems. The interfacial adhesion of semicrystalline polymers was not well understood. We thus studied the adhesion behaviour of LLDPE as a semicrystalline polymer. The results indicated that the time and temperature dependence of seal strength is a consequence of the fraction of amorphous phase available at the interface of films. The seal strength had a linear correlation with the square root of sealing time which was also supported by the welding models. The slope of this linear correlation increased with temperature. This work was followed concurrently by two main approaches: analysis of polymer chain behaviour from microscopic point of view based on reptation theory and conventional macroscopic analysis based on bulk properties of the polymer. Failure mechanisms and fractured surfaces were also analyzed after peeling. Moreover, the topography and morphology of

  9. FERMI multi-chip module

    CERN Multimedia

    This FERMI multi-chip module contains five million transistors. 25 000 of these modules will handle the flood of information through parts of the ATLAS and CMS detectors at the LHC. To select interesting events for recording, crucial decisions are taken before the data leaves the detector. FERMI modules are being developed at CERN in partnership with European industry.

  10. Reconfigurable Networks-on-Chip

    CERN Document Server

    Chen, Sao-Jie; Tsai, Wen-Chung; Hu, Yu-Hen

    2012-01-01

    This book provides a comprehensive survey of recent progress in the design and implementation of Networks-on-Chip. It addresses a wide spectrum of on-chip communication problems, ranging from physical, network, to application layers. Specific topics that are explored in detail include packet routing, resource arbitration, error control/correction, application mapping, and communication scheduling. Additionally, a novel bi-directional communication channel NoC (BiNoC) architecture is described, with detailed explanation.   Written for practicing engineers in need of practical knowledge about the design and implementation of networks-on-chip; Includes tutorial-like details to introduce readers to a diverse range of NoC designs, as well as in-depth analysis for designers with NoC experience to explore advanced issues; Describes a variety of on-chip communication architectures, including a novel bi-directional communication channel NoC.     From the Foreword: Overall this book shows important advances over the...

  11. Single cell electroporation on chip

    NARCIS (Netherlands)

    Valero, Ana

    2006-01-01

    In this thesis the results of the development of microfluidic cell trap devices for single cell electroporation are described, which are to be used for gene transfection. The performance of two types of Lab-on-a-Chip trapping devices was tested using beads and cells, whereas the functionality for si

  12. Silicon ball grid array chip carrier

    Science.gov (United States)

    Palmer, David W.; Gassman, Richard A.; Chu, Dahwey

    2000-01-01

    A ball-grid-array integrated circuit (IC) chip carrier formed from a silicon substrate is disclosed. The silicon ball-grid-array chip carrier is of particular use with ICs having peripheral bond pads which can be reconfigured to a ball-grid-array. The use of a semiconductor substrate such as silicon for forming the ball-grid-array chip carrier allows the chip carrier to be fabricated on an IC process line with, at least in part, standard IC processes. Additionally, the silicon chip carrier can include components such as transistors, resistors, capacitors, inductors and sensors to form a "smart" chip carrier which can provide added functionality and testability to one or more ICs mounted on the chip carrier. Types of functionality that can be provided on the "smart" chip carrier include boundary-scan cells, built-in test structures, signal conditioning circuitry, power conditioning circuitry, and a reconfiguration capability. The "smart" chip carrier can also be used to form specialized or application-specific ICs (ASICs) from conventional ICs. Types of sensors that can be included on the silicon ball-grid-array chip carrier include temperature sensors, pressure sensors, stress sensors, inertia or acceleration sensors, and/or chemical sensors. These sensors can be fabricated by IC processes and can include microelectromechanical (MEM) devices.

  13. Methods for making a multi-layer seal for electrochemical devices

    Science.gov (United States)

    Chou, Yeong-Shyung; Meinhardt, Kerry D.; Stevenson, Jeffry W.

    2007-05-29

    Multi-layer seals are provided that find advantageous use for reducing leakage of gases between adjacent components of electrochemical devices. Multi-layer seals of the invention include a gasket body defining first and second opposing surfaces and a compliant interlayer positioned adjacent each of the first and second surfaces. Also provided are methods for making and using the multi-layer seals, and electrochemical devices including said seals.

  14. 19 CFR 12.63 - Seal-skin or sea-otter-skin waste.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 1 2010-04-01 2010-04-01 false Seal-skin or sea-otter-skin waste. 12.63 Section... OF THE TREASURY SPECIAL CLASSES OF MERCHANDISE Fur-Seal Or Sea-Otter Skins § 12.63 Seal-skin or sea-otter-skin waste. Seal-skin or sea-otter-skin waste composed of small pieces not large enough to...

  15. Numerical Research of the Measurement Error of Temperature Thermocouples with the Isolated Seal

    OpenAIRE

    Atroshenko Yuliana K.; Bychkova Alena A.; Strizhak Pavel A.

    2015-01-01

    Mathematical models of heattransfer are developed for an assessment of measurement errors of temperature by thermocouples with an isolated and uninsulated seal. Dependences of necessary time of heating (for authentic measurement) for the thermocouples with an isolated seal manufactured of different materials are set. It is shown that for thermocouples with isolated seal minimum necessary duration of heating up slightly exceeds this index for thermocouples with an uninsulated seal.

  16. Viscous sealing glass compositions for solid oxide fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Cheol Woon; Brow, Richard K.

    2016-12-27

    A sealant for forming a seal between at least two solid oxide fuel cell components wherein the sealant comprises a glass material comprising B.sub.2O.sub.3 as a principal glass former, BaO, and other components and wherein the glass material is substantially alkali-free and contains less than 30% crystalline material.

  17. Molecular epidemiology of seal parvovirus, 1988-2014

    NARCIS (Netherlands)

    R. Bodewes (Rogier); R. Hapsari (Rebriarina); A.R. García (Ana Rubio); G.J. Sá Nchez Contreras (Guillermo J.); M.W.G. van de Bildt (Marco); M. De Graaf (Mira); T. Kuiken (Thijs); A.D.M.E. Osterhaus (Albert)

    2014-01-01

    textabstractA novel parvovirus was discovered recently in the brain of a harbor seal (Phoca vitulina) with chronic meningo-encephalitis. Phylogenetic analysis of this virus indicated that it belongs to the genus Erythroparvovirus, to which also human parvovirus B19 belongs. In the present study, the

  18. Status of the harbour seal (Phoca vitulina in Southern Scandinavia

    Directory of Open Access Journals (Sweden)

    Morten Tange Olsen

    2013-09-01

    Full Text Available The harbour seal population in Southern Scandinavia has experienced repeated declines caused by hunting and epizootics. These events have shaped the current distribution and abundance of the population. This paper assesses the current status of the population. We estimate trends in abundance of harbour seals from long term survey data, compare these with historic trends inferred from previously published material, and discuss past and potential threats to the harbour seal population of Southern Scandinavia. It is evident that harbour seals have disappeared from haulout areas along the Danish shores of Kattegat and in the westernmost part of the Baltic Sea, where they were previously numerous. In the 1920-30s, when abundance was at its lowest, the population is estimated to have been only a fraction of its original size. Following 30 years of protection the population is currently approaching historic abundance and might have reached the carrying capacity in some areas. Further development depends largely on effects of future epizootics, anthropogenic disturbance, and availability of suitable haulout sites.

  19. Relative immunocompetence of the newborn harbour seal, phoca vitulina

    NARCIS (Netherlands)

    P.S. Ross (Peter); R.L. de Swart (Rik); I.K.G. Visser (Ilona); E.J. Vedder (Lies); W. Murk; W.D. Bowen; A.D.M.E. Osterhaus (Albert)

    1994-01-01

    textabstractThe immune system of many mammalian species is not fully developed at birth, with newborns obtaining temporary immunological protection from maternal antibodies. Little is known of the immune system of the harbour seal, and developmental aspects of its immune system have not been systema

  20. Sealing of polymer micro-structures by over-moulding

    DEFF Research Database (Denmark)

    Vingaard, Mathias; Christiansen, Jesper de Claville

    2012-01-01

    A concept for sealing of polymer micro-structures by over-moulding with polystyrene was devised and investigated by both experiments and simulations. The depth to which the melt filled the structure, i.e. a groove in the surface of the insert, before solidification was compared with results from ...

  1. Development of Improved Seals and Closures for Dry Diving Suits.

    Science.gov (United States)

    1979-01-31

    Viking latex. The neoprene is more resistant to solvent than the latex. The multiple lip seal is easy to clean, its multiple chambers resist the...did not cause irritation to the diver under his weight belt nor limit his movement. The zipper was easy to lubricate with beeswax and allowed the

  2. Oil Leakage from the Seal Ring of a Scroll Compressor

    Science.gov (United States)

    Kobayashi, Naoki; Fukui, Atsushi; Horiguchi, Hironori; Tsujimoto, Yoshinobu; Toyama, Toshiyuki

    In scroll compressors for air conditioners, there is a compressor with back-pressure chamber spaced by seal ring behind orbiting scroll. High pressure in the backpressure chamber presses the orbiting scroll to fixed scroll. In the case that lubrication oil and refrigerant gas with high pressure and temperature in the backpressure chamber leak to low pressure chamber through the seal ring, the efficiency of compressor decreases and the oil circulation rate can increase. In the present study the leakage characteristics of lubrication oil from the backpressure chamber to the low pressure chamber were investigated. In experiment, it was found that the oil leakage is larger for higher rotational speed of rotating disk, higher viscosity of oil and smaller pressure difference between the backpressure and low-pressure chambers. This could be explained by the calculation in which the seal ring was assumed to have a tilt angle. It was also found in the calculation that oil leakage is larger due to the thicker oil film between the seal ring and the rotating disk in the case of higher rotational speed of the disk, higher viscosity of oil and smaller pressure difference between the backpressure and low-pressure chambers.

  3. The Vascular Flora of Seal Island National Wildlife Refuge 2003

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This is an extensive list of flora found during a 10 day survey in the summer of 2003 on Seal Island, Maine. The primary objectives of this study were to compile a...

  4. WIPP shaft seal system parameters recommended to support compliance calculations

    Energy Technology Data Exchange (ETDEWEB)

    Hurtado, L.D.; Knowles, M.K. [Sandia National Labs., Albuquerque, NM (United States); Kelley, V.A.; Jones, T.L.; Ogintz, J.B. [INTERA Inc., Austin, TX (United States); Pfeifle, T.W. [RE/SPEC, Inc., Rapid City, SD (United States)

    1997-12-01

    The US Department of Energy plans to dispose of transuranic waste at the Waste Isolation Pilot Plant (WIPP), which is sited in southeastern New Mexico. The WIPP disposal facility is located approximately 2,150 feet (650 m) below surface in the bedded halite of the Salado Formation. Prior to initiation of disposal activities, the Department of Energy must demonstrate that the WIPP will comply with all regulatory requirements. Applicable regulations require that contaminant releases from the WIPP remain below specified levels for a period of 10,000 years. To demonstrate that the WIPP will comply with these regulations, the Department of Energy has requested that Sandia National Laboratories develop and implement a comprehensive performance assessment of the WIPP repository for the regulatory period. This document presents the conceptual model of the shaft sealing system to be implemented in performance assessment calculations conducted in support of the Compliance Certification Application for the WIPP. The model was developed for use in repository-scale calculations and includes the seal system geometry and materials to be used in grid development as well as all parameters needed to describe the seal materials. These calculations predict the hydrologic behavior of the system. Hence conceptual model development is limited to those processes that could impact the fluid flow through the seal system.

  5. Study on Seal Technology for Nuclear Material Control

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The seals have important application in nuclear safeguards, and are designed to record unauthorizedaccess or entry to inspected material and equipment. They can provide assurance for the continuity andintegrity of nuclear material accountancy. It is very useful to improve the inspection efficiency by means

  6. Seal Hairs Tell World History of Gold and Silver Mining

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    @@ The fluctuation of mercury (Hg) concentration in seal hairs over the past 2,000years in a lake-sediment core on King George Island, West Antarctica, has been found to be closely correlated with ancient activities of gold and silver mining by using Hg-amalgamation process around the world.

  7. STUDY ON MECHANICAL DEFORMATIONS OF THE PRIMARY FRONTAL SEALING

    Directory of Open Access Journals (Sweden)

    Monica BÂLDEA

    2015-05-01

    Full Text Available In many applications one of the primary sealing rings is mounted pressed into another ring, tightening materials to be made makes the required stretched tension in the outer ring and compression in the inner ring.It will be considered as the basis for calculating ultimate elongation for tenacious materials and breaking limit for brittle materials.

  8. Miniature fuel cells relieve gas pressure in sealed batteries

    Science.gov (United States)

    Frank, H. A.

    1971-01-01

    Miniature fuel cells within sealed silver zinc batteries consume evolved hydrogen and oxygen rapidly, preventing pressure rupturing. They do not significantly increase battery weight and they operate in all battery life phases. Complete gas pressure control requires two fuel cells during all phases of operation of silver zinc batteries.

  9. The status of the harbour seal (Phoca vitulina in Ireland

    Directory of Open Access Journals (Sweden)

    Michelle A Cronin

    2010-09-01

    Full Text Available The status of Ireland’s harbour seal population and its relationship with that of Britain and Western Europe are poorly understood. Prior to 2003, limited research efforts and poor co-ordination of survey methods fell short at providing an accurate assessment of overall distribution and population size on a regional or national scale. However, in August 2003, the Republic of Ireland’s harbour seal population was assessed by means of a geographically extensive survey conducted during the annual moult, providing an up-to-date minimum population estimate and a reliable baseline for future surveys. Trends on a national scale could not be assessed due to absence of a reliable historic population estimate; however there is some evidence of local decreases and increases in harbour seal numbers in Northern Ireland and southwest Ireland respectively. Research effort to date on aspects of the ecology of the harbour seal in the Republic of Ireland is reviewed and current research and management priorities highlighted.

  10. Assessment of Water Quality of Runoff from Sealed Asphalt Surfaces

    Science.gov (United States)

    This report discusses the results of runoff tests from recently-sealed asphalt surfaces conducted at EPA's Urban Watershed Research Facility (UWRF) in Edison, New Jersey. Both bench-scale panels and full-scale test plots were evaluated. Full-scale tests were performed on an asp...

  11. 20 CFR 369.4 - Inappropriate use of the seal.

    Science.gov (United States)

    2010-04-01

    ... coffee mugs and computer mouse pads with text relevant to benefits paid by the Railroad Retirement Board... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Inappropriate use of the seal. 369.4 Section 369.4 Employees' Benefits RAILROAD RETIREMENT BOARD INTERNAL ADMINISTRATION, POLICY AND PROCEDURES...

  12. Cystic duct closure by sealing with bipolar electrocoagulation

    DEFF Research Database (Denmark)

    Schulze, S; Damgaard, B; Jørgensen, Lars Nannestad;

    2010-01-01

    BACKGROUND: Cystic duct leakage after cholecystectomy is not uncommon and is a potentially serious complication. The aim of this study was to assess a bipolar sealing system (LigaSure) for closure of the cystic duct. METHODS: The records from consecutive laparoscopic cholecystectomies performed i...

  13. Seals as collectors of oceanographic data in the coastal zone

    DEFF Research Database (Denmark)

    Del Villar-Guerra, Diego; Cronin, Michelle; Dabrowski, Tomasz;

    2012-01-01

    stratification, up/downwellings and the onset of the thermocline, and provide unique insights into the marine environment in and around the bay, where no previous oceanographic studies have been conducted. Strong correlation between the seal-derived temperature data and in situ temperature recorders and modelled...

  14. Plastic Sealed Thermal Expansion Packer for Thermal Recovery

    Institute of Scientific and Technical Information of China (English)

    Liu Li; Jiang Hua

    1995-01-01

    @@ According to the requirements of wellbore heatinsulation technique and selective zonal steaminjection technique in heavy-oil steam-injection recovery process, the Oil Recovery Technique Department of Liaohe Petroleum Exploration and Production Bureau and Shuguang Oil Recovery Plant have cooperatively designed and developed a plastic sealed thermal expansion packer for thermal recovery.

  15. Supercritical fluid chromatography of fish, shark and seal oils

    DEFF Research Database (Denmark)

    Borch-Jensen, Christina; Mollerup, Jørgen

    1996-01-01

    Various natural and treated fish, shark liver and seal oils have been analyzed by supercritical fluid chromatography (SFC) using a non-polar capillary column. The lipids are separated according to molecular mass. The lipid groups found included free fatty acids, cholesterol, squalene, vitamins, wax...

  16. Canine distemper virus in Lake Baikal seals (Phoca sibirica).

    NARCIS (Netherlands)

    L.V. Mamaev; I.K.G. Visser (Ilona); S.I. Belikov; N.N. Denikina; T.C. Harder (Timm); L. Goatley; B. Rima; B. Edginton; A.D.M.E. Osterhaus (Albert); T. Barrett (Thomas)

    1996-01-01

    textabstractThe virus epizootic which resulted in significant mortality in Siberian seals (Phoca sibirica) in Lake Baikal during 1987/88 was caused by canine distemper virus. Sequence analysis of the virus glycoprotein genes revealed that it was most closely related to recent European field isolates

  17. Contaminant-induced immunotoxicity in harbour seals: Wildlife at risk?

    NARCIS (Netherlands)

    P.S. Ross (Peter); R.L. de Swart (Rik); R. Addison; H. van Loveren (Henk); J.G. Vos (Joseph); A.D.M.E. Osterhaus (Albert)

    1996-01-01

    textabstractPersistent, lipophilic polyhalogenated aromatic hydrocarbons (PHAHs) accumulate readily in the aquatic food chain and are found in high concentrations in seals and other marine mammals. Recent mass mortalities among several marine mammal populations have been attributed to infection by m

  18. Hydrogen Vent Ground Umbilical Quick Disconnect - Flight Seal Advanced Development

    Science.gov (United States)

    Girard, Doug; Jankowski, Fred; Minich, Mark C.; Yu, Weiping

    2012-01-01

    This project is a team effort between NASA Engineering (NE) and Team QNA Engineering personnel to provide support for the Umbilical Systems Development project which is funded by Advanced Exploration Systems (AES) and 21st Century Launch Complex. Specifically, this project seeks to develop a new interface between the PPBE baselined Legacy SSP LH2 Vent Arm QD probe and SLS vent seal.

  19. Means for sealing hemp packings in gas pipelines

    Energy Technology Data Exchange (ETDEWEB)

    Pistek, P.; Kubat, J.; Novak, L.

    1981-02-15

    The means for sealing hemp packings in gas pipelines has the following composition: 25-35% diethylene glycol, 10-15% glycerin, 10-15% triethylene glycol, 5-15% high ethylene glycols with an average molecular weight of 300, 20-35% the monobutyl ether of triethylene glycol, 4-7% ethoxylated p-chlorophenol, and 5-15% monoethanol amine.

  20. 12 CFR 1700.3 - Official logo and seal.

    Science.gov (United States)

    2010-01-01

    ... DEVELOPMENT OFHEO ORGANIZATION AND FUNCTIONS ORGANIZATION AND FUNCTIONS § 1700.3 Official logo and seal. The... of a structure consisting of a solid two-tiered pedestal base topped by a solid triangular shape, which represents the roof of the structure. Placed between the base and the top are the letters...