WorldWideScience

Sample records for chemical protective performance

  1. Reliability performance testing of totally encapsulating chemical protective suits

    International Nuclear Information System (INIS)

    Johnson, J.S.; Swearengen, P.M.

    1991-01-01

    The need to assure a high degree of reliability for totally encapsulating chemical protective (TECP) suits has been recognized by Lawrence Livermore National Laboratory's (LLNL) Hazards Control Department for some time. The following four tests were proposed as necessary to provide complete evaluation of TECP suit performance: 1. Quantitative leak test (ASTM draft), 2. Worst-case chemical exposure test (conceptual), 3. Pressure leak-rate test (complete, ASTM F1057-87), and 4. Chemical leak-rate test (ASTM draft). This paper reports on these tests which should be applied to measuring TECP suit performance in two stages: design qualification tests and field use tests. Test 1, 2, and 3 are used as design qualification tests, and tests 3 and 4 are used as field use tests

  2. Military Psychology. Volume 9, Number 4, 1997. Effects of Chemical Protective Clothing on Military Performance

    Science.gov (United States)

    1997-01-01

    Hoarding or stealing chemical protective Rationalization (finding reasons not to train in equipment chemical protective clothing) Hypochondriasis ...overreactions involves development of bodily com- plaints, that is, somatization , which result in dramatic increases in reports for sick call or visits to the...doctor (The Adjutant General, 1979; Weisaeth, 1993). This hypochondriasis occurs as people focus attention on their bodies and internal sensations

  3. Chemical protective clothing; a study into the ability of staff to perform lifesaving procedures

    Science.gov (United States)

    Coates, M.; Jundi, A.; James, M.

    2000-01-01

    Objective—To investigate the ability of medical and nursing staff to perform certain tasks while wearing a chemical protection suit with a respirator. Tasks chosen were those that would be required before decontamination. Methods—Ten experienced accident and emergency doctors (middle grade and consultants) and 10 nurses were asked to perform certain tasks that were judged to be life saving, relevant to triage, or necessary to confirm death, on an advanced life support manikin, while wearing a TST-Sweden chemical protection suit. The operators were objectively assessed by one of the authors for achieving each task, then asked to make a subjective assessment of the difficulty experienced. Results—Medical staff were asked to ventilate the manikin using a bag-valve-mask, intubate within 30 seconds, apply monitor electrodes and cables and check cardiac rhythm, apply gel pads and defibrillate safely, and finally, fold the cruciform triage card to show "RED", and attach it to the manikin. All the doctors completed these tasks, except for one, who could only intubate the manikin after several attempts. Nursing staff were asked to open and apply an oxygen mask, adjust oxygen flow, size and insert an oropharyngeal airway, ventilate the manikin using a bag-valve-mask, apply a pressure bandage to a limb, and fold the cruciform triage card to show "YELLOW", and attach it to the manikin. All the nurses completed these tasks. Operators reported varying degrees of difficulty, the most difficult tasks were those requiring fine movements or delicate control. Generally, operators found the butyl rubber gloves cumbersome. Communication difficulties were frequently reported. Although only intubation was formally timed, tasks were perceived to take longer. Some operators found the suits too warm and uncomfortable. Conclusion—Should the need arise, the TST-Sweden chemical protection suits would enable experienced doctors and nurses to perform lifesaving measures effectively

  4. Field selection of chemical protective clothing and respiratory protection

    International Nuclear Information System (INIS)

    Pinette, S.; Dodgen, C.; Morley, M.

    1991-01-01

    Safety professionals who must choose appropriate personal protective equipment for hazardous substance response or hazardous waste sites require useable information about the effectiveness of the various products available. Each hazardous waste operation involves a unique combination of chemical hazards requiring a unique combination of protective apparel. A chemical protective suit or respirator must be chosen for each site and each operation on the site. No single protective suit is effective against all chemical hazards. No single respirator is the best choice in every situation. Various sources of information on the effectiveness of protective clothing products will be discussed. Site-specific permeation testing of the proposed protective clothing options will also be discussed. It is both possible and practical to obtain specific information about the degree of protection afforded by a particular suit against a particular chemical mixture. It is also important to know how long the suit will last. Choosing adequate respiratory protection is a complex process. Respirator cartridge performance depends on various environmental factors as well as upon the combination and concentration of chemicals in the air. Once characterization of the air at a site has been accomplished, it may be appropriate to select an alternative to airline respirators and SCBAs. Respirator cartridges can be tested against specific chemical mixtures using worse case environmental factors. The results can be used to predict both the effectiveness and duration of protection afforded by respirator cartridges which can reduce costs and worker fatigue

  5. Chemical protection against ionizing radiation

    International Nuclear Information System (INIS)

    Livesey, J.C.; Reed, D.J.

    1987-01-01

    Over 40 years have passed since the research of the Manhattan Project suggested the possibility of chemical protection against ionizing radiation. During that time, much has been learned about the nature of radiation-induced injury and the factors governing the expression of that injury. Thousands of compounds have been tested for radioprotective efficacy, and numerous theories have been proposed to account for these actions. The literature on chemical radioprotection is large. In this article, the authors consider several of the mechanisms by which chemicals may protect against radiation injury. They have chosen to accent this view of radioprotector research as opposed to that research geared toward developing specific molecules as protective agents because they feel that such an approach is more beneficial in stimulating research of general applicability. This paper describes the matrix of biological factors upon which an exogenous radioprotector is superimposed, and examines evidence for and against various mechanisms by which these agents may protect biological systems against ionizing radiation. It concludes with a brief outlook for research in chemical radioprotection

  6. Plant protective chemicals in forestry

    International Nuclear Information System (INIS)

    Mueller, A.; Freidhager, R.; Hackl, J.

    1993-12-01

    The aim of the present study is to examine critically the use of pesticides in forestry and the resulting problems. Further, the study points out possibilities for dispensing with chemical treatments altogether. This work is intended to assist those deciding upon suitable forest protection procedures. There are also comments on the particular dangers arising from the use of pesticides (R-Saetze) and safety advice as regards their proper application. The first part of the present study contains both a discussion of the humanotoxicological and ecological consequences of pesticide applications in forestry as well as the legal basis for the sale and use of pesticides in Austria. The following parts (herbicides, insecticides, rodenticides, game deterrents, fungicides) treat the use of pesticides according to their respective area of application. Discussed here are chemical properties, toxicity, and the environmental compatibility of the pesticides in question, including demonstrations of environmentally sound ways to avoid or restrict the use of pesticides. (authors)

  7. Chemical application strategies to protect water quality.

    Science.gov (United States)

    Rice, Pamela J; Horgan, Brian P; Barber, Brian L; Koskinen, William C

    2018-07-30

    Management of turfgrass on golf courses and athletic fields often involves application of plant protection products to maintain or enhance turfgrass health and performance. However, the transport of fertilizer and pesticides with runoff to adjacent surface waters can enhance algal blooms, promote eutrophication and may have negative impacts on sensitive aquatic organisms and ecosystems. Thus, we evaluated the effectiveness of chemical application setbacks to reduce the off-site transport of chemicals with storm runoff. Experiments with water soluble tracer compounds confirmed an increase in application setback distance resulted in a significant increase in the volume of runoff measured before first off-site chemical detection, as well as a significant reduction in the total percentage of applied chemical transported with the storm runoff. For example, implementation of a 6.1 m application setback reduced the total percentage of an applied water soluble tracer by 43%, from 18.5% of applied to 10.5% of applied. Evaluation of chemographs revealed the efficacy of application setbacks could be observed with storms resulting in lesser (e.g. 100 L) and greater (e.g. > 300 L) quantities of runoff. Application setbacks offer turfgrass managers a mitigation approach that requires no additional resources or time inputs and may serve as an alternative practice when buffers are less appropriate for land management objectives or site conditions. Characterizing potential contamination of surface waters and developing strategies to safeguard water quality will help protect the environment and improve water resource security. This information is useful to grounds superintendents for designing chemical application strategies to maximize environmental stewardship. The data will also be useful to scientists and regulators working with chemical transport and risk models. Copyright © 2018. Published by Elsevier Inc.

  8. Chemical Solutions of Fire Protection Problems

    Directory of Open Access Journals (Sweden)

    Vakhitova, L.M.

    2015-11-01

    Full Text Available The modern approaches to the creation of fire protective coatings by modifying intumescent systems by nanomaterials with study of the chemical reaction mechanisms under the high temperatures influence were considered. A systematic study of the interactions of components of polyphosphate type intumescent blend were carried out, a well-defined correlations between the directions of chemical processes and fire retardant properties of intumescent coatings were found. Efficient ways to simultaneous increase of fireprotective efficiency and performance characteristics of intumescent coatings (operatin life, resistance to environmental factors and bioсontamination were proposed. The results of fundamental research allowed to develop new formulations of flame retardant compositions, whose properties have been confirmed by tests in accordance with existing standardized methods, these results were introduced into production.

  9. Latin American protected areas: Protected from chemical pollution?

    Science.gov (United States)

    Rodríguez-Jorquera, Ignacio A; Siroski, Pablo; Espejo, Winfred; Nimptsch, Jorge; Choueri, Paloma Gusso; Choueri, Rodrigo Brasil; Moraga, Claudio A; Mora, Miguel; Toor, Gurpal S

    2017-03-01

    Protected areas (PAs) are critically important means to preserve species and maintain natural ecosystems. However, the potential impacts of chemical pollution on PAs are seldom mentioned in the scientific literature. Research on the extent of the occurrence of chemical pollution inside PAs and in-depth assessments of how chemical contaminants may adversely affect the maintenance of species abundance, species survival, and ecosystem functions are scarce to nonexistent. We investigated 1) the occurrence of chemical contaminants inside 119 PAs in Latin America from publically available databases, and 2) reviewed case studies of chemical contaminants and pollution in 4 Latin American PAs. Cases of chemical pollution and contamination inside Latin American PAs mostly originated from sources such as mining, oil, and gas extraction. To date, the focus of the research on chemical pollution research inside Latin American PAs has been primarily on the detection of contamination, typically limited to trace metals. Where management actions have occurred, they have been reactive rather than proactive. Protected areas established in wetlands are the most affected by chemical pollution. Based on the information from the pollution and/or contamination occurrence and the case studies analyzed, Latin American PAs are not well safeguarded from chemical pollution, resulting in both challenges and opportunities to conserve biodiversity and ecosystems. Integr Environ Assess Manag 2017;13:360-370. © 2016 SETAC. © 2016 SETAC.

  10. Chemical protection against ionizing radiation. Final report

    International Nuclear Information System (INIS)

    Livesey, J.C.; Reed, D.J.; Adamson, L.F.

    1984-08-01

    The scientific literature on radiation-protective drugs is reviewed. Emphasis is placed on the mechanisms involved in determining the sensitivity of biological material to ionizing radiation and mechanisms of chemical radioprotection. In Section I, the types of radiation are described and the effects of ionizing radiation on biological systems are reviewed. The effects of ionizing radiation are briefly contrasted with the effects of non-ionizing radiation. Section II reviews the contributions of various natural factors which influence the inherent radiosensitivity of biological systems. Inlcuded in the list of these factors are water, oxygen, thiols, vitamins and antioxidants. Brief attention is given to the model describing competition between oxygen and natural radioprotective substances (principally, thiols) in determining the net cellular radiosensitivity. Several theories of the mechanism(s) of action of radioprotective drugs are described in Section III. These mechanisms include the production of hypoxia, detoxication of radiochemical reactive species, stabilization of the radiobiological target and the enhancement of damage repair processes. Section IV describes the current strategies for the treatment of radiation injury. Likely areas in which fruitful research might be performed are described in Section V. 495 references

  11. Chemical protection against ionizing radiation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Livesey, J.C.; Reed, D.J.; Adamson, L.F.

    1984-08-01

    The scientific literature on radiation-protective drugs is reviewed. Emphasis is placed on the mechanisms involved in determining the sensitivity of biological material to ionizing radiation and mechanisms of chemical radioprotection. In Section I, the types of radiation are described and the effects of ionizing radiation on biological systems are reviewed. The effects of ionizing radiation are briefly contrasted with the effects of non-ionizing radiation. Section II reviews the contributions of various natural factors which influence the inherent radiosensitivity of biological systems. Inlcuded in the list of these factors are water, oxygen, thiols, vitamins and antioxidants. Brief attention is given to the model describing competition between oxygen and natural radioprotective substances (principally, thiols) in determining the net cellular radiosensitivity. Several theories of the mechanism(s) of action of radioprotective drugs are described in Section III. These mechanisms include the production of hypoxia, detoxication of radiochemical reactive species, stabilization of the radiobiological target and the enhancement of damage repair processes. Section IV describes the current strategies for the treatment of radiation injury. Likely areas in which fruitful research might be performed are described in Section V. 495 references.

  12. Chemically resistant, biocompatible and microstructured surface protection

    International Nuclear Information System (INIS)

    Hoffmann, W.; Pham, M.T.; Hueller, J.

    1984-01-01

    Subject of the invention are chemicallly resistant, biocompatible, and microstructured surface protective coatings of electronic elements and sensors including chemical sensors. Such coatings consist of a radiation-modified organic substance made of a microlithographic material. Modification can be achieved by irradiation with ions, atoms or molecules having an energy between 1 KeV and 1 MeV and a flux between 10 13 and 10 18 particles per cm 2

  13. Using the skin protective lotion IB1 as a substitute for chemical protective gloves.

    Science.gov (United States)

    Ophir, Nimrod; Milk, Nadav; Mayer, Talia; Ravfogel, Shaul; Yavnai, Nirit; Eisenkraft, Arik; Kadar, Tamar; Kassirer, Michael; Rosman, Yossi

    2016-10-01

    We aimed to evaluate the performance of medical personnel in using the IB1 topical protective lotion on their hands and wrists together with standard disposable medical gloves, compared to standard-issued medical chemical protective gloves. This randomized cross-over study included 144 medical personnel. Primary endpoints were time-to-completion of autoinjection; success rate, number of attempts, and time-to-achieve successful endotracheal intubation; time-to-achieve satisfactory tube fixation; time-to-draw and inject the content of an ampoule; and the total time-to-perform all medical procedures. Secondary endpoints included the subjective assessment of convenience to perform these four procedures with each protective measure. Mean time was significantly shorter using IB1 compared to chemical protective gloves for tube fixation, ampoule drawing, and the total time-to-perform all procedures (58.6±22.7 seconds vs. 71.7±29.7; 31.5±21.8 vs. 38.2±19.4; 137.4±56.1 vs. 162.5±63.6, respectively; Pgloves (Pgloves significantly shorten the time-to-perform medical procedures requiring fine motor dexterities and is subjectively more convenient than chemical protective gloves. IB1 should be considered as an appropriate alternative for medical teams in a chemical event. Copyright © 2016 Elsevier Inc. All rights reserved.

  14. A Survey of Wood Protection Chemicals, Tree Killers and Sprayers ...

    African Journals Online (AJOL)

    chemicals used in wood protection (preservation) within Makurdi metropolis. A purposive, non-random sampling was undertaken in Makurdi metropolis to identify wood protection chemicals/tree-killers available in agrochemical stores, ...

  15. Chemical protective clothing - State of the art and the future

    International Nuclear Information System (INIS)

    Perkins, J.L.

    1990-01-01

    Clothing used to protect the skin from exposure to chemicals (CPC) is an integral part of many work-places. Only 10-15 years ago the strategy behind selecting CPC to afford this protection was to find a type of CPC which was essentially liquid-proof and would therefore protect the skin from exposure to a liquid chemical. However, in the last 10 years there has been an explosion of data in the industrial hygiene field related to the permeation of chemical protective clothing by liquid chemicals. These data indicate clearly that when CPC is exposed to a chemical, it may not disintegrate or degrade, but nevertheless, will be permeated by the chemical and the skin will be exposed. This has led to a new strategy for selecting CPC which essentially assumes that any exposure of the skin is harmful. Consequently, a worst-case scenario is assumed when selecting CPC and often the garment with the best permeation properties is selected regardless of cost. This philosophy is prompted by a lack of knowledge concerning the skin and how it is permeated by industrial chemicals in their liquid and vapor states. The interests in the last 10 years in CPC has led to new developments and an exciting future for protective clothing. Several new laminated polymeric materials are now being used in both gloves and full-body suits. These polymers are plastic rather than elastomeric and therefore do not afford good dexterity properties. However, their permeability properties are extremely good. In addition, further research on dermal penetration should give the industrial hygienist the necessary information to perform risk assessments for skin exposure. These new risk assessment strategies should negate the current need to overprotect workers. Overprotection often leads to unnecessary costs and can lead to increased stress on the worker in the form of heat stress

  16. Radiation protection in clinical chemical laboratories

    International Nuclear Information System (INIS)

    Jacob, K.

    1980-01-01

    In the clinical-chemical laboratory, the problems of the personal radiation protection can be handled relatively simply. Important conditions are certain requirements as far as the building is concerned and the keeping to protection measures to invoid ingestion, inhalation, and resorption of open radioactive substances. Very intensive attention must be paid to a clean working technique in order to be able to exclude the danger of contamination which is very disturbing during the extremely sensitive measurements. The higgest problem in the handling of open radioactive substances, however, is in our opinion the waste management because it requires which space and personnel this causing high costs. Furthermore, since 1 January 1979, the permission for the final storage of radioactive waste in the shut down mine ASSE was taken back from the county collection places and it cannot be said yet if and when this permission will be given again. (orig./HP) [de

  17. Heat stress in chemical protective clothing: Porosity and vapour resistance

    NARCIS (Netherlands)

    Havenith, G.; Hartog, E.A. den; Martini, S.

    2011-01-01

    Heat strain in chemical protective clothing is an important factor in industrial and military practice. Various improvements to the clothing to alleviate strain while maintaining protection have been attempted. More recently, selectively permeable membranes have been introduced to improve

  18. How to Protect Yourself from Chemicals

    Science.gov (United States)

    ... yourself from chemicals It may seem kind of scary when you think about all the chemicals around ... Follow the recommendations of local, state, and federal warnings on fish that are safe to eat. Find ...

  19. Chemicals for crop protection and pest control

    National Research Council Canada - National Science Library

    Green, Maurice B; Hartley, Gilbert Spencer; West, Trustham Frederick

    1977-01-01

    .... For the most part, the conventional classification into insecticides, herbicides and fungicides has been followed and some more specialized chemicals are also classified according to their biological...

  20. State and tendencies of chemical protection against ionizing radiation

    International Nuclear Information System (INIS)

    Siegel, G.; Tapp, E.; Haehn, J.; Hannig, H.; Dlaske, R.; Martinek, K.

    1977-01-01

    Papers published in 1976 in the field of chemical protection against ionizing radiation are reviewed. Protection studies in vitro and in vivo, the biochemical, pharmacological and toxic effects, the mechanisms of protection of radioprotective agents and the trends in this field of research are described. (author)

  1. State and tendencies of chemical protection against ionizing radiation

    International Nuclear Information System (INIS)

    Siegel, G.; Tapp, E.; Haehn, J.; Hannig, H.; Dlaske, R.

    1976-03-01

    Papers published in 1974 in the field of chemical protection against ionizing radiation are reviewed. Protection studies in vitro and in vivo, the biochemical, pharmacological and toxic effects, the mechanisms of protection of radioprotective agents and the trends in this field of research are described. (author)

  2. State and tendencies of chemical protection against ionizing radiation

    International Nuclear Information System (INIS)

    Siegel, G.; Tapp, E.; Haehn, J.; Hannig, H.; Dlaske, R.; Martinek, K.

    1977-01-01

    Papers published in 1975 in the field of chemical protection against ionizing radiation are reviewed. Protection studies in vitro and in vivo, the biochemical, pharmacological and toxic effects, the mechanisms of protection of radioprotective agents and the trends in this field of research are described. (author)

  3. Chemical protection from high LET radiation

    International Nuclear Information System (INIS)

    Ando, Koichi; Koike, Sachiko; Matsushita, Satoru; Kanai, Tatsuaki; Ohara, Hiroshi

    1992-01-01

    Radioprotection by WR151327 from high LET fast neutrons was investigated and compared with that from low LET radiation. Radiation damage in bone marrow, intestine, skin and leg length were all protected by a pretreatment with 400 mg/kg WR151327. Most prominent protection was observed for bone marrow, which gave a Dose Modifying Factor (DMF) of 2.2 against γ rays. Identical protection was observed between early and late radiation damage. WR151327 protected fast neutrons less efficiently than γ rays; 40% for bone marrow and 80% for skin leg. Pathological findings indicated that hyperplastic change in both dermis and epidermis associated with late skin shrinkage. Laser doppler flow-metry showed a good relationship between reduction of blood flow and late skin shrinkage. Irradiation of skin by heavy particle Carbon-12 indicated that skin shrinkage was modified by unirradiated surrounding normal tissues, which proposed a significant role of 'Volume Effect' in radiation damage. Tumor tissues were less protected by WR151327 than normal tissues. Dependence of radioprotection by WR151327 on tissue oxygen concentration is a probable reason to explain the difference between normal and tumor tissues. (author)

  4. Assuring Condition and Inventory Accountability of Chemical Protective Suits

    National Research Council Canada - National Science Library

    2000-01-01

    .... As part of the Defense Logistics Agency's efforts to consolidate depot operations and improve inventory accuracy, chemical protective suits were transferred to the Defense Depot, Albany, Georgia, during FY 1991.

  5. State and tendencies of chemical protection against ionizing radiation

    International Nuclear Information System (INIS)

    Siegel, G.; Tapp, E.; Hannig, H.; Dlaske, R.; Haehn, J.; Martinek, K.

    1980-01-01

    Papers published in 1978 in the field of chemical protection against ionizing radiation are reviewed. Protection studies in in-vivo and model systems, the biochemical, pharmacological and toxic effects, and modes of action of radioprotective agents are described and the trends in this field of research appreciated. (author)

  6. State and tendencies of chemical protection against ionizing radiation

    International Nuclear Information System (INIS)

    Siegel, G.; Tapp, E.; Hannig, H.; Dlaske, R.; Papendieck, W.; Martinek, K.; Haehn, J.

    1982-01-01

    Papers published in 1979 and 1980 in the field of chemical protection against ionizing radiation are reviewed. Protection studies in in-vivo and model systems, the biochemical, pharmacological and toxic effects, and modes of action of radioprotective agents are described and the trends in this field of research estimated. (author)

  7. 46 CFR 153.933 - Chemical protective clothing.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Chemical protective clothing. 153.933 Section 153.933 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SHIPS... Protective Clothing”, Third Edition, 1987, available from the American Conference of Governmental Industrial...

  8. Protecting chemical plants against terrorist attacks: a review

    NARCIS (Netherlands)

    Khakzad Rostami, N.; Reniers, G.L.L.M.E.

    2015-01-01

    Protection of hazardous establishments such as chemical plants intentional incidents has drawn attention from safety and security experts since 9/11 terrorist attacks in the U.S. Although major steps have been taken since, the recent intentional incidents in two chemical plants in France in June and

  9. Environmental protection, a task of chemical engineering

    Energy Technology Data Exchange (ETDEWEB)

    Schlachter, H

    1980-12-01

    The environmental burden in air and water in Germany is surveyed. The terms 'eco-unobjectionable technology' and 'disposal technology' are then considered with the aid of examples. These are fundamental chemical engineering approaches for reducing or eliminating environmental burdens due to industrial production processes. 'Eco-unobjectionable processes' are those in which undesired pollutants are not even formed, i.e. when possible emissions are eliminated at source. If this is only partly possible, or impossible, then disposal measures are adopted. This means removal of unavoidable pollutants from waste gases and waste water, and the disposal of other wastes.

  10. Centralized radiation protection in the chemical industry

    International Nuclear Information System (INIS)

    Kistner, A.C.

    2006-01-01

    At Novartis the so-called ''ZSS'' department (''Zentraler Strahlenschutz'') respectively (''central radiation protection'') administrates all in-house data concerning radiation. When the time for a contemporary and thus more flexible software solution had come, the heterogenous company had many demands to be met - for example reorganizational ability, multi-client capability, device-specific scalability as well as customizability and individual data entries concerning all employees exposed to ionized radiation. A customized software-solution was then developed and build by Sirius Technologies AG from Basel. The application is composed modularly and therefore adapts well to miscellaneous data sets of various working areas, devices, radiation sources, factories, partners, approvals, isotopes etc. The conception even contains future enhancement and supplementation. (orig.)

  11. Health risk assessments of DEHP released from chemical protective gloves.

    Science.gov (United States)

    Chao, Keh-Ping; Huang, Chan-Sheng; Wei, Chung-Ying

    2015-01-01

    The substance di-2-ethylhexyl phthalate (DEHP) is widely used as a plasticizer in chemical protective gloves to improve their flexibility and workability. However, it is possible that workers using protective gloves to handle various solvents may be exposed to DEHP leached by the solvents. Using an ASTM F739 permeation cell, it was found that BTEX solvents permeating through the glove samples dissolved DEHP from the gloves. Even without continuously contacting the permeant, DEHP was released from the contaminated glove samples during the desorption experiments. The DEHP leaching amounts were found to be inversely correlated to the permeability coefficients of BTEX in the glove samples. This result implied that the larger the amount of DEHP released from the glove samples, the higher the permeation resistance of gloves. Although chemical protective gloves provide adequate skin exposure protection to workers, the dermal exposure model developed herein indicates that leaching of DEHP from the glove samples may pose a potential health risk to the workers who handle BTEX. This study suggests that the selection of protective gloves should not only be concerned with the chemical resistance of the gloves but also the health risk associated with leaching of chemicals, such as DEHP, used in the manufacturing of the gloves. Copyright © 2014 Elsevier B.V. All rights reserved.

  12. Radiation-chemical disinfection of dissolved impurities and environmental protection

    International Nuclear Information System (INIS)

    Petrukhin, N.V.; Putilov, A.V.

    1986-01-01

    Radiation-chemical neutralization of dissolved toxic impurities formed in the production processes of different materials, while modern plants being in use, is considered. For the first time the processes of deep industrial waste detoxication and due to this peculiarities of practically thorough neutralization of dissolved toxic impurities are considered. Attention is paid to devices and economic factors of neutralization of dissolved toxic impurities. The role of radiation-chemical detoxication for environment protection is considered

  13. 2006 Chemical Biological Individual Protection (CBIP) Conference and Exhibition

    Science.gov (United States)

    2006-03-09

    Requirements Office (JRO), MAJ W. Scott Smedley , Joint Requirements Office for Chemical, Biological, Radiological, and Nuclear Defense JPEO...Decker Director of Engineering 410-436-5600 www.ecbc.army.mil Gabe Patricio, JPEO 703 681-0808 Robert Wattenbarger, JPMOIP 703 432-3198 Canadian CBRN...UNCLASSIFIED Joint Requirements Office for Chemical, Biological, and Nuclear Defense MAJ W. Scott Smedley 8 March 2006 Individual Protection Conference

  14. Radiation protection in the pharmaceutical-chemical industry

    International Nuclear Information System (INIS)

    Griesser, R.

    1992-01-01

    Some aspects of the use of ionizing radiation in research in the pharmaceutical and chemical industries will be discussed, the emphasis being placed on the handling of open radioactive materials in research laboratories. The compliance with official regulations and the preparation of company internal radiation protection regulations are described. 1 tab., 9 refs

  15. Chemical vapor deposition: A technique for applying protective coatings

    Energy Technology Data Exchange (ETDEWEB)

    Wallace, T.C. Sr.; Bowman, M.G.

    1979-01-01

    Chemical vapor deposition is discussed as a technique for applying coatings for materials protection in energy systems. The fundamentals of the process are emphasized in order to establish a basis for understanding the relative advantages and limitations of the technique. Several examples of the successful application of CVD coating are described. 31 refs., and 18 figs.

  16. Radiation, chemical and biological protection. Mass destruction weapons

    International Nuclear Information System (INIS)

    Janasek, D.; Svetlik, J.

    2005-01-01

    In this text-book mass destruction weapons and radiation, chemical and biological protection are reviewed. The text-book contains the following chapter: (1) Mass destruction weapons; (2) Matter and material; (3) Radioactive materials; (4) Toxic materials; (5) Biological resources; (6) Nuclear energetic equipment; Appendices; References.

  17. International physical protection self-assessment tool for chemical facilities.

    Energy Technology Data Exchange (ETDEWEB)

    Tewell, Craig R.; Burdick, Brent A.; Stiles, Linda L.; Lindgren, Eric Richard

    2010-09-01

    This report is the final report for Laboratory Directed Research and Development (LDRD) Project No.130746, International Physical Protection Self-Assessment Tool for Chemical Facilities. The goal of the project was to develop an exportable, low-cost, computer-based risk assessment tool for small to medium size chemical facilities. The tool would assist facilities in improving their physical protection posture, while protecting their proprietary information. In FY2009, the project team proposed a comprehensive evaluation of safety and security regulations in the target geographical area, Southeast Asia. This approach was later modified and the team worked instead on developing a methodology for identifying potential targets at chemical facilities. Milestones proposed for FY2010 included characterizing the international/regional regulatory framework, finalizing the target identification and consequence analysis methodology, and developing, reviewing, and piloting the software tool. The project team accomplished the initial goal of developing potential target categories for chemical facilities; however, the additional milestones proposed for FY2010 were not pursued and the LDRD funding therefore was redirected.

  18. Pregnant Employee Protection Program in a Large Chemical Company.

    Science.gov (United States)

    Frey, Gunild; Schuster, Michael; Oberlinner, Christoph; Queier-Wahrendorf, Annette; Lang, Stefan; Yong, Mei

    2015-09-01

    To assess whether a structured employee protection program for pregnant workers at a chemical company has an impact on pregnancy outcomes. Reported pregnancies (n = 1402) between 2003 and 2010 and their outcomes were documented using questionnaires at the time of pregnancy report, end of pregnancy, and 1 year later. Potential maternal exposures were assessed using job histories, workplace inspections, and questionnaires. Participation was 86% overall and was consistently high across subgroups.Pregnancy losses (10.9%), pregnancy complications, and preterm births (8.1%) were in agreement with rates in the general population and were independent of type of work and maternal exposure category. Pregnancy complication rates in this chemical company are not statistically elevated than that in the general population, as suggested in a previous study. The protection program may play a role in preventing complications that may have occurred.

  19. Influence of Chemical Surface Modification of Woven Fabrics on Ballistic and Stab Protection of Multilayer Packets

    Directory of Open Access Journals (Sweden)

    Diana GRINEVIČIŪTĖ

    2014-06-01

    Full Text Available In order to achieve enhanced protective and wear (flexibility, less bulkiness properties of ballistic and stab protecting panels the investigation of chemical surface modification of woven p-aramid fabrics was performed applying different chemical composition shear thickening fluid (STF which improves friction inside fabric structure. For the chemical treatment silicic acid and acrylic dispersion water solutions were used and influence of their different concentrations on panels’ protective properties were investigated. Results of ballistic tests of multilayer protective panel have revealed that shear thickening effect was negligible when shooting at high energy range (E > 440 J. Determination of stab resistance of p-aramid panels has shown that different chemical composition of STFs had different influence on protective properties of the panels. Application of low concentrations of silicic acid determined higher stab resistance values comparing to higher concentrations of acrylic dispersion water solutions. At this stage of research stab tests results as ballistic ones determined that STF application for multilayer p-aramid fabrics protective panels is more efficient at low strike energy levels. DOI: http://dx.doi.org/10.5755/j01.ms.20.2.3138

  20. Chemical protection and sensitization to ionizing radiation:molecular investigations

    International Nuclear Information System (INIS)

    Badiello, R.

    1980-01-01

    Chemical radioprotection and radiosensitization are induced by the presence of certain chemical compounds, which reduce or enhance the effect of ionizing radiation on living organisms. Such substances are either naturally present or may be artificially introduced in the living cells. Chemical radioprotectors are interesting for possible application in the health protection of both professionally exposed workers and patients treated by radiation for diagnostic and thereapeutic purposes. Interest in chemical radiosensitization has increased recently because of its potential application in the radiotherapy of tumours. Both radioprotection and radiosensitization occur by means of complicated mechanisms, which at first correspond to very fast reactions. The mechanism of the interaction between such substances and radiation-induced biological radicals has been investigated by means of pulse radiolysis and rapid mixing techniques. Examples of the application of these techniques are given to illustrate how information has been obtained on the molecular basis of radiation chemical modi-fication at the cellular level. In particular some interactions between model systems of biological interest (DNA, DNA components, enzymes, amino acids, etc.) and sulphur-containing radioprotectors (glutathione, cysteine, etc.) and/or electroaffinic radiosensitizers, are described. (H.K.)

  1. Bioremediation performance as related to chemical availability

    International Nuclear Information System (INIS)

    Loehr, R.; Olivera, F.; Webster, M.

    1995-01-01

    Two side-by-side field prepared bed land treatment units (PBLTU) were evaluated. One PBLTU (H unit) treated soils containing chemicals from a diesel spill that had occurred about 12 months earlier. The other PBLTU (G unit) treated soils containing crude oil that had been in the soil for many decades. Laboratory slurry treatability studies and indicated that the hydrocarbons in both soils could be bioremediated if adequate nutrients were provided. The PBLTU had nutrients applied periodically, and were operated in a manner consistent with good operational guidelines. PBLTU performance was based on reductions in mobility, toxicity, and chemical concentration. Spatially random soil samples were taken from the two field PBLTU monthly and analyzed for the above parameters as well as nutrients and pH. Periodically, microbial numbers and type in the soil samples also were evaluated. Performance was monitored over an 18 month period. In the H unit, no detectable TPH reductions occurred although petroleum hydrocarbon degrading microorganisms existed in the soil and other conditions were appropriate for bioremediation. GC/MS analyses indicated reduction in some specific hydrocarbons. The H unit soils had low chemical mobility as determined by leachability tests (TCLP, SPLP) and had low relative toxicity as determined by Microtox trademark

  2. 75 FR 18850 - National Protection and Programs Directorate; Chemical Facility Anti-Terrorism Standards...

    Science.gov (United States)

    2010-04-13

    ... Directorate; Chemical Facility Anti-Terrorism Standards Personnel Surety Program AGENCY: National Protection...-terrorism Vulnerability Information (CVI), Sensitive Security Information (SSI), or Protected Critical... . SUPPLEMENTARY INFORMATION: Program Description The Chemical Facility Anti-Terrorism Standards (CFATS), 6 CFR...

  3. Playing Chemical Plant Environmental Protection Games with Historical Monitoring Data.

    Science.gov (United States)

    Zhu, Zhengqiu; Chen, Bin; Reniers, Genserik; Zhang, Laobing; Qiu, Sihang; Qiu, Xiaogang

    2017-09-29

    The chemical industry is very important for the world economy and this industrial sector represents a substantial income source for developing countries. However, existing regulations on controlling atmospheric pollutants, and the enforcement of these regulations, often are insufficient in such countries. As a result, the deterioration of surrounding ecosystems and a quality decrease of the atmospheric environment can be observed. Previous works in this domain fail to generate executable and pragmatic solutions for inspection agencies due to practical challenges. In addressing these challenges, we introduce a so-called Chemical Plant Environment Protection Game (CPEP) to generate reasonable schedules of high-accuracy air quality monitoring stations (i.e., daily management plans) for inspection agencies. First, so-called Stackelberg Security Games (SSGs) in conjunction with source estimation methods are applied into this research. Second, high-accuracy air quality monitoring stations as well as gas sensor modules are modeled in the CPEP game. Third, simplified data analysis on the regularly discharging of chemical plants is utilized to construct the CPEP game. Finally, an illustrative case study is used to investigate the effectiveness of the CPEP game, and a realistic case study is conducted to illustrate how the models and algorithms being proposed in this paper, work in daily practice. Results show that playing a CPEP game can reduce operational costs of high-accuracy air quality monitoring stations. Moreover, evidence suggests that playing the game leads to more compliance from the chemical plants towards the inspection agencies. Therefore, the CPEP game is able to assist the environmental protection authorities in daily management work and reduce the potential risks of gaseous pollutants dispersion incidents.

  4. Playing Chemical Plant Environmental Protection Games with Historical Monitoring Data

    Science.gov (United States)

    Reniers, Genserik; Zhang, Laobing; Qiu, Xiaogang

    2017-01-01

    The chemical industry is very important for the world economy and this industrial sector represents a substantial income source for developing countries. However, existing regulations on controlling atmospheric pollutants, and the enforcement of these regulations, often are insufficient in such countries. As a result, the deterioration of surrounding ecosystems and a quality decrease of the atmospheric environment can be observed. Previous works in this domain fail to generate executable and pragmatic solutions for inspection agencies due to practical challenges. In addressing these challenges, we introduce a so-called Chemical Plant Environment Protection Game (CPEP) to generate reasonable schedules of high-accuracy air quality monitoring stations (i.e., daily management plans) for inspection agencies. First, so-called Stackelberg Security Games (SSGs) in conjunction with source estimation methods are applied into this research. Second, high-accuracy air quality monitoring stations as well as gas sensor modules are modeled in the CPEP game. Third, simplified data analysis on the regularly discharging of chemical plants is utilized to construct the CPEP game. Finally, an illustrative case study is used to investigate the effectiveness of the CPEP game, and a realistic case study is conducted to illustrate how the models and algorithms being proposed in this paper, work in daily practice. Results show that playing a CPEP game can reduce operational costs of high-accuracy air quality monitoring stations. Moreover, evidence suggests that playing the game leads to more compliance from the chemical plants towards the inspection agencies. Therefore, the CPEP game is able to assist the environmental protection authorities in daily management work and reduce the potential risks of gaseous pollutants dispersion incidents. PMID:28961188

  5. Playing Chemical Plant Environmental Protection Games with Historical Monitoring Data

    Directory of Open Access Journals (Sweden)

    Zhengqiu Zhu

    2017-09-01

    Full Text Available The chemical industry is very important for the world economy and this industrial sector represents a substantial income source for developing countries. However, existing regulations on controlling atmospheric pollutants, and the enforcement of these regulations, often are insufficient in such countries. As a result, the deterioration of surrounding ecosystems and a quality decrease of the atmospheric environment can be observed. Previous works in this domain fail to generate executable and pragmatic solutions for inspection agencies due to practical challenges. In addressing these challenges, we introduce a so-called Chemical Plant Environment Protection Game (CPEP to generate reasonable schedules of high-accuracy air quality monitoring stations (i.e., daily management plans for inspection agencies. First, so-called Stackelberg Security Games (SSGs in conjunction with source estimation methods are applied into this research. Second, high-accuracy air quality monitoring stations as well as gas sensor modules are modeled in the CPEP game. Third, simplified data analysis on the regularly discharging of chemical plants is utilized to construct the CPEP game. Finally, an illustrative case study is used to investigate the effectiveness of the CPEP game, and a realistic case study is conducted to illustrate how the models and algorithms being proposed in this paper, work in daily practice. Results show that playing a CPEP game can reduce operational costs of high-accuracy air quality monitoring stations. Moreover, evidence suggests that playing the game leads to more compliance from the chemical plants towards the inspection agencies. Therefore, the CPEP game is able to assist the environmental protection authorities in daily management work and reduce the potential risks of gaseous pollutants dispersion incidents.

  6. Chemical Protective Clothing for Law Enforcement Patrol Officers and Emergency Medical Services when Responding to Terrorism with Chemical Weapons

    National Research Council Canada - National Science Library

    Arca, Victor J; Marshall, Stephen M; Lake, William A; Fedele, Paul D

    1999-01-01

    .... This testing examined how well the complete protective suit ensembles protect the wearer against vapor adsorption at the skin by exposing test participants wearing the suits to a chemical agent simulant (methyl salicylate...

  7. Chemical Protective Clothing for Law Enforcement Patrol Officers and Emergency Medical Services when Responding to Terrorism with Chemical Weapons

    National Research Council Canada - National Science Library

    Arca, Victor

    2001-01-01

    .... This testing examined how well the complete protective suit ensembles protect the wearer against vapor adsorption by the skin by exposing test participants wearing the suits to a chemical agent simulant (methyl salicylate...

  8. 75 FR 68370 - Agency Information Collection Activities: Office of Infrastructure Protection; Chemical Security...

    Science.gov (United States)

    2010-11-05

    ... DEPARTMENT OF HOMELAND SECURITY National Protection and Programs Directorate [Docket No. DHS-2010-0071] Agency Information Collection Activities: Office of Infrastructure Protection; Chemical Security...: The Department of Homeland Security (DHS), National Protection and Programs Directorate (NPPD), Office...

  9. Practicing chemical process safety: a look at the layers of protection

    International Nuclear Information System (INIS)

    Sanders, Roy E.

    2004-01-01

    This presentation will review a few public perceptions of safety in chemical plants and refineries, and will compare these plant workplace risks to some of the more traditional occupations. The central theme of this paper is to provide a 'within-the-fence' view of many of the process safety practices that world class plants perform to pro-actively protect people, property, profits as well as the environment. It behooves each chemical plant and refinery to have their story on an image-rich presentation to stress stewardship and process safety. Such a program can assure the company's employees and help convince the community that many layers of safety protection within our plants are effective, and protect all from harm

  10. Fabrication and wear protection performance of superhydrophobic surface on zinc

    Energy Technology Data Exchange (ETDEWEB)

    Wan Yong, E-mail: wanyong@qtech.edu.cn [School of Mechanical Engineering, Qingdao Technological University, 11 Fushun Road, Qingdao 266033 (China); Wang Zhongqian; Xu Zhen; Liu Changsong [School of Mechanical Engineering, Qingdao Technological University, 11 Fushun Road, Qingdao 266033 (China); Zhang Junyan [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Lanzhou 730000 (China)

    2011-06-15

    A simple two-step process has been developed to render zinc surface superhydrophobic, resulting in low friction coefficient and long wear resistance performance. The ZnO film with uniform and packed nanorod structure was firstly created by immersing the zinc substrates into 4% N,N-dimethylformamide solution. The as-fabricated surface was then coated a layer of fluoroalkylsilane (FAS) by gas phase deposition. Scanning electron microscopy (SEM) and water contact angle (WCA) measurement have been performed to characterize the morphological feature, chemical composition and superhydrophobicity of the surface. The resulting surfaces have a WCA as high as 156 deg. and provide effective friction-reducing and wear protection for zinc substrate.

  11. Fabrication and wear protection performance of superhydrophobic surface on zinc

    International Nuclear Information System (INIS)

    Wan Yong; Wang Zhongqian; Xu Zhen; Liu Changsong; Zhang Junyan

    2011-01-01

    A simple two-step process has been developed to render zinc surface superhydrophobic, resulting in low friction coefficient and long wear resistance performance. The ZnO film with uniform and packed nanorod structure was firstly created by immersing the zinc substrates into 4% N,N-dimethylformamide solution. The as-fabricated surface was then coated a layer of fluoroalkylsilane (FAS) by gas phase deposition. Scanning electron microscopy (SEM) and water contact angle (WCA) measurement have been performed to characterize the morphological feature, chemical composition and superhydrophobicity of the surface. The resulting surfaces have a WCA as high as 156 deg. and provide effective friction-reducing and wear protection for zinc substrate.

  12. Performance evaluation of accelerated protection for microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Wei, P.; Lin, X. [Huazhong Univ. of Science and Technology (China); Klimek, A. [Powertech Labs Inc., Surrey, BC (Canada); Bo, Z. [Alstom Grid Automation (United Kingdom)

    2010-07-01

    The constraints of existing power system facilities are becoming apparent as the demand for electricity increases. This paper discussed the use of microgrids as a means of improving power quality, safety, and stability. There are currently 2 main methods for protecting microgrids, notably voltage measurement, and a differential current method. The methods both assume that the microgrid is divided into zones determined by the location of distributed generators (DGs) in the power system. When faults are detected by protection relays, the DG in the microgrid zone will be shut off. Conventional protection coordination methods result in long fault clearance times. Relay coordination calculation methods are complicated when microgrids include a number of DGs that may be vulnerable to fault disturbances. This paper described a non-communication protection technique designed to detect faults zones using a superimposed phase current of the sound phase following breaker trips at the other end of the faulted line section. The method was designed to accelerate the tripping speed of the breaker at the local end of the faulted line. The technique can also be used to protect distribution systems with double source or radial configurations. 5 refs., 2 tabs., 14 figs.

  13. Influence of a carbohydrate drink on performance of military personnel in NBC protective clothing

    NARCIS (Netherlands)

    Dokkum, W. van; Boxtel, L.B.J. van; Dijk, M.J. van; Boer, L.C.; Beek, E.J. van der

    1996-01-01

    Background: The increased threat of nuclear, biological and chemical (NBC) weapons underlines the need of protective clothing and gas masks, but this may impair performance. Thus, attention should be focused on the nutritional requirements. Hypothesis: Optimal performance is guaranteed if the supply

  14. Evaluation of Personal Chemical Vapor Protection for Patrol and Tactical Law Enforcement

    National Research Council Canada - National Science Library

    Fedele, Paul D; Lake, William L; Arca, Victor J; Marshall, Stephen M; Mitchell, David B

    2002-01-01

    In Domestic Preparedness efforts, the US Army Soldier and Biological Chemical Command and the Maryland State Police, have evaluated personal chemical protective systems for use in patrol and tactical...

  15. Comparison of performance test for protective aprons

    International Nuclear Information System (INIS)

    Fukutomi, Yukimi; Yoshimoto, Masahiro; Kawakami, Toshiaki

    1989-01-01

    Each one radioprotective apron (lead equivalent, 0.35 mmPb) was commercially available in November 1988 from 7 domestic and 3 foreign companies. According to the JIS standards 4803, these aprons were evaluated for the following items: 1) display of aprons, including packing and the structure; 2) non-breaking test, including appearance, size, lead equivalent, and uniformity; 3) breaking test, including lead equivalent, uniformity, stregth, and structure; 4) feeling of wearing an apron. An overall evaluation revealed that only two aprons were in accordance with the JIS standard. Careful wearing of the protective apron is stressed. (N.K.)

  16. Endocrine-disrupting chemicals and public health protection

    DEFF Research Database (Denmark)

    Zoeller, R Thomas; Brown, T R; Doan, L L

    2012-01-01

    An endocrine-disrupting chemical (EDC) is an exogenous chemical, or mixture of chemicals, that can interfere with any aspect of hormone action. The potential for deleterious effects of EDC must be considered relative to the regulation of hormone synthesis, secretion, and actions and the variabili...

  17. High performance protection circuit for power electronics applications

    Energy Technology Data Exchange (ETDEWEB)

    Tudoran, Cristian D., E-mail: cristian.tudoran@itim-cj.ro; Dădârlat, Dorin N.; Toşa, Nicoleta; Mişan, Ioan [National Institute for Research and Development of Isotopic and Molecular Technologies, 67-103 Donat, PO 5 Box 700, 400293 Cluj-Napoca (Romania)

    2015-12-23

    In this paper we present a high performance protection circuit designed for the power electronics applications where the load currents can increase rapidly and exceed the maximum allowed values, like in the case of high frequency induction heating inverters or high frequency plasma generators. The protection circuit is based on a microcontroller and can be adapted for use on single-phase or three-phase power systems. Its versatility comes from the fact that the circuit can communicate with the protected system, having the role of a “sensor” or it can interrupt the power supply for protection, in this case functioning as an external, independent protection circuit.

  18. Chemical stability of fluorine-containing coatings of cold drying for radiation - protection technique articles

    International Nuclear Information System (INIS)

    Shigorina, I.I.; Zvyagintseva, N.V.; Egorov, B.N.

    1977-01-01

    The chemical stability of fluorolon coatings, which are not subjected to heat treatment or hot drying during application, has been studied. The test for layer life-time has been performed by submerging specimens in agressive medium. The time for one upper removable layer to fail under steady action of agressive liquid is found to be: > 12 months at 20 deg C, 6-9 months at 40 deg C; at 60 deg C the time of layer stability depends upon medium: 1 month for nitric, 2 months for acetic, 2-3 months for sulphuric and hydrochloric acid. The coatings are recommended for practical application in radiation-protective technique

  19. Possibility of the development of a Serbian protection system against chemical accidents

    Directory of Open Access Journals (Sweden)

    Dejan R. Inđić

    2012-10-01

    Full Text Available The paper presents a draft of a system model for responding in case of chemical accidents in accordance with the current legislation regarding the environment protection, the structure and elements of the existing response system in case of chemical accidents, other works dealing with the issue as well as the prospects planned by those responsible for the environmental protection. The paper discuss the possibilities of different institutions and agencies of the Republic of Serbia to engage in specialized methods of cooperation and protection against chemical hazards in accordance with Article X of the Convention on the Prohibition of Chemical Weapons.

  20. Security risk assessment and protection in the chemical and process industry

    OpenAIRE

    Reniers, Genserik; van Lerberghe, Paul; van Gulijk, Coen

    2014-01-01

    This article describes a security risk assessment and protection methodology that was developed for use in the chemical- and process industry in Belgium. The approach of the method follows a risk-based approach that follows desing principles for chemical safety. That approach is beneficial for workers in the chemical industry because they recognize the steps in this model from familiar safety models .The model combines the rings-of-protection approach with generic security practices including...

  1. Current global standards for chemical protective clothing: how to choose the right protection for the right job?

    Science.gov (United States)

    VAN WELY, Eric

    2017-01-01

    The first standards for chemical protective clothing (CPC) emerged mid to late 1980’s and have evolved since as most standards are revisited every 5 yr. Over the past years, we have also seen a strengthening of the chemical and worker protection legislation around the globe (various forms of REACH) but also protection of workers. The most prevalent standards originate under the auspices of the International Standards Organisation (ISO), European Committee for Standardisation (CEN) or under various US standards organisations (e.g. NFPA, ASTM). Protective clothing against hazardous materials is required in many of the professional and non-professional activities of everyday life. Effective and adequate protection is important in many scenarios from household (e.g. cleaning agents, peroxides, acids and bases, paints), to agricultural (e.g. fuel, pesticides), to medical (e.g. pharmaceuticals and active ingredients), to industrial production (e.g. petro-chemicals, chemicals, paints, adhesive and coatings) but also manufacturing of many products (e.g. light bulbs, cars, semi-conductors), during various emergency activities (e.g. boat, rail or road accidents as well as fire-fighting in an urban and industrial setting), and finally, military operations or response to incidents of terrorism. Nevertheless, CPC must remain the last line of defence whenever possible through a preference for less hazardous chemicals, less dangerous processes and handling operations, and by engineering controls to reduce and minimise human contact with the chemicals. This article provides information about the selection, use, care and maintenance (SUCAM) of protective clothing against chemical and microbiological hazards. PMID:29046493

  2. Agronomic performance of five banana cultivars under protected cultivation

    Science.gov (United States)

    Banana has been grown both in open-field and protected cultivation in Turkey. So far protected cultivation is very popular due to the high yield and quality. The objective of the study was to evaluate agronomic performance of five new banana cultivars under plastic greenhouse. ‘MA 13’, ‘Williams’, ‘...

  3. A suggested approach to the selection of chemical and biological protective clothing--meeting industry and emergency response needs for protection against a variety of hazards.

    Science.gov (United States)

    Stull, Jeffrey O

    2004-01-01

    The paper describes the development of a comprehensive decision logic for selection and use of biological and chemical protective clothing (BCPC). The decision logic recognizes the separate areas of BCPC use among emergency, biological, and chemical hazards. The proposed decision logic provides a system for type classifying BCPC in terms of its compliance with existing standards (for emergency applications), the overall clothing integrity, and the material barrier performance. Type classification is offered for garments, gloves, footwear, and eye/face protection devices. On the basis of multiple, but simply designed flowcharts, the type of BCPC appropriate for specific biological and chemical hazards can be selected. The decision logic also provides supplemental considerations for choosing appropriate BCPC features.

  4. Evaluation of X-ray shielding performance of protective aprons

    International Nuclear Information System (INIS)

    Kumagai, Michitomo; Shintani, Mitsuo; Kuranishi, Makoto

    1999-01-01

    Lead equivalent, which offers protection against x-rays, is rated with a 100 kV tube voltage in Japanese Industrial Standard (JIS) Z 4501-1988, Testing method of lead equivalent for x-ray protective devices.'' However, the actual tube voltage in general diagnostic examinations (normal to special radiography; including computed tomography, CT) is 50 to 150 kV. Therefore, we measured whether the performance of current lead aprons (three products) and protective aprons using composite materials (two products) changes at 60 to 141 kV of tube voltage. Furthermore, we evaluated x-ray shielding performance by measuring the transmission ratio of scattered x-rays. The lead equivalent of two currently used lead aprons was almost the same at all voltages. However, in one currently used lead apron and both protective aprons made of composite materials, lead equivalent decreased rapidly when tube voltage exceeded 100 kV. The transmission ratio of scattered x-rays increased with increasing tube voltage in all of the protective aprons examined. Further, in all aprons examined, the transmission ratio of scattered x-rays declined with widening of the scatter angle. As mentioned above, the x-ray shielding performance of some x-ray protective aprons suddenly decreased at tube voltages over 100 kV. Thus the performance of x-ray protective aprons should be published, and JIS Z 4501 needs to be revised. (author)

  5. Evaluation of X-ray shielding performance of protective aprons

    Energy Technology Data Exchange (ETDEWEB)

    Kumagai, Michitomo; Shintani, Mitsuo; Kuranishi, Makoto [Toyama Medical and Pharmaceutical Univ. (Japan). Hospital

    1999-04-01

    Lead equivalent, which offers protection against x-rays, is rated with a 100 kV tube voltage in Japanese Industrial Standard (JIS) Z 4501-1988, Testing method of lead equivalent for x-ray protective devices.`` However, the actual tube voltage in general diagnostic examinations (normal to special radiography; including computed tomography, CT) is 50 to 150 kV. Therefore, we measured whether the performance of current lead aprons (three products) and protective aprons using composite materials (two products) changes at 60 to 141 kV of tube voltage. Furthermore, we evaluated x-ray shielding performance by measuring the transmission ratio of scattered x-rays. The lead equivalent of two currently used lead aprons was almost the same at all voltages. However, in one currently used lead apron and both protective aprons made of composite materials, lead equivalent decreased rapidly when tube voltage exceeded 100 kV. The transmission ratio of scattered x-rays increased with increasing tube voltage in all of the protective aprons examined. Further, in all aprons examined, the transmission ratio of scattered x-rays declined with widening of the scatter angle. As mentioned above, the x-ray shielding performance of some x-ray protective aprons suddenly decreased at tube voltages over 100 kV. Thus the performance of x-ray protective aprons should be published, and JIS Z 4501 needs to be revised. (author)

  6. Chemical conversion coating for protecting magnesium alloys from corrosion

    Science.gov (United States)

    Bhargava, Gaurang; Allen, Fred M.; Skandan, Ganesh; Hornish, Peter; Jain, Mohit

    2016-01-05

    A chromate-free, self-healing conversion coating solution for magnesium alloy substrates, composed of 10-20 wt. % Mg(NO.sub.3).sub.2.6H.sub.2O, 1-5 wt. % Al(NO.sub.3).sub.3.9H.sub.2O, and less than 1 wt. % of [V.sub.10O.sub.28].sup.6- or VO.sub.3.sup.- dissolved in water. The corrosion resistance offered by the resulting coating is in several hundreds of hours in salt-spray testing. This prolonged corrosion protection is attributed to the creation of a unique structure and morphology of the conversion coating that serves as a barrier coating with self-healing properties. Hydroxoaluminates form the backbone of the barrier protection offered while the magnesium hydroxide domains facilitate the "slow release" of vanadium compounds as self-healing moieties to defect sites, thus providing active corrosion protection.

  7. Intergranular corrosion protective of austenitic stainless steel chemical equipment

    International Nuclear Information System (INIS)

    Kuzyukov, A.N.

    1994-01-01

    A complex of protective measures was developed for each concrete case of intergranular fracture of equipment, i.e.: decrease in the level of strains, surfacing with materials resistant to intergranular fracture under the conditions; permissible correction of process parameters, permitting a shift in corrosion potential towards decrease in the rate of intergranular corrosion. It is shown that even if the eguipment was subject to interfranular corrosion, but the fracture is not of catastrophic character, it proved possible to develop and apply complex methods of protection from the above types of corrosion fracture and to elongate the service life by 5-15 years

  8. Effectiveness of Human Research Protection Program Performance Measurements.

    Science.gov (United States)

    Tsan, Min-Fu; Nguyen, Yen

    2017-10-01

    We analyzed human research protection program performance metric data of all Department of Veterans Affairs research facilities obtained from 2010 to 2016. Among a total of 25 performance metrics, 21 (84%) showed improvement, four (16%) remained unchanged, and none deteriorated during the study period. The overall improvement from these 21 performance metrics was 81.1% ± 18.7% (mean ± SD), with a range of 30% to 100%. The four performance metrics that did not show improvement all had initial noncompliance/incidence rates of performance metrics that showed improvement ranged from 0.05% to 60%. However, of the 21 performance metrics that showed improvement, 10 had initial noncompliance/incidence rates of performance measurement is an effective tool in improving the performance of human research protection programs.

  9. Formation, adhesion and mechanical/chemical properties of protective coatings

    International Nuclear Information System (INIS)

    Mattox, D.M.

    1979-01-01

    Some general considerations for protective coatings are discussed. It is suggested that ceramic coatings may provide a class of coatings applicable to high temperature turbine blades for use in a corrosive/erosive environment. In particular, the ceraming glass materials would seem to hold promise, but little or nothing has been done on depositing these materials by vacuum processes

  10. Application of mechano-chemical synthesis for protective coating

    Indian Academy of Sciences (India)

    This can either be prevented by using grinding medium and container of same material of the milled material or by adding a coating of the milled material on them. The paper describes the observations made during a mechano-chemical reaction, being used for coating the balls and vials in a planetary ball mill.

  11. Playing chemical plant environmental protection games with historical monitoring data

    NARCIS (Netherlands)

    Zhu, Zhengqiu; Chen, Bin; Reniers, G.L.L.M.E.; Zhang, L.; Qiu, S.; Qiu, Xiaogang

    2017-01-01

    The chemical industry is very important for the world economy and this industrial sector represents a substantial income source for developing countries. However, existing regulations on controlling atmospheric pollutants, and the enforcement of these regulations, often are insufficient in such

  12. Radiation-chemical sanitation of dissolved pollutants and environmental protection

    International Nuclear Information System (INIS)

    Petrukhin, N.V.; Putilov, A.V.

    1986-01-01

    Radiation-chemical sanitation of dissolved toxic pollutants resulted from the production processes of different substances and modern equipment operation is considered. The processes of fundamental industrial sewage processing and, as a result, features of practically total disposal of dissolved toxic agents are considered for the first time

  13. Toxic Industrial Chemical Tests of Resistance to Permeation by Protective Suits

    National Research Council Canada - National Science Library

    Klemperer, Elizabeth

    2005-01-01

    A Natick program to select and test protective materials for soldiers and first responders who face a threat from chemical accidents or terrorist attacks was applied under Congressional legislation...

  14. Functional Fit Evaluation to Determine Optimal Ease Requirements in Canadian Forces Chemical Protective Gloves

    National Research Council Canada - National Science Library

    Tremblay-Lutter, Julie

    1995-01-01

    A functional fit evaluation of the Canadian Forces (CF) chemical protective lightweight glove was undertaken in order to quantify the amount of ease required within the glove for optimal functional fit...

  15. Chemical warfare protection for the cockpit of future aircraft

    Science.gov (United States)

    Pickl, William C.

    1988-01-01

    Currently systems are being developed which will filter chemical and biological contaminants from crew station air. In order to maximize the benefits of these systems, a method of keeping the cockpit contaminant free during pilot ingress and egress is needed. One solution is to use a rectangular plastic curtain to seal the four edges of the canopy frame to the canopy sill. The curtain is stored in a tray which is recessed into the canopy sill and unfolds in accordion fashion as the canopy is raised. A two way zipper developed by Calspan could be used as an airlock between the pilot's oversuit and the cockpit. This system eliminates the pilot's need for heavy and restrictive CB gear because he would never be exposed to the chemical warfare environment.

  16. Reproductive Toxic Chemicals at Work and Efforts to Protect Workers' Health: A Literature Review

    Directory of Open Access Journals (Sweden)

    Kyung-Taek Rim

    2017-06-01

    Full Text Available A huge number of chemicals are produced and used in the world, and some of them can have negative effects on the reproductive health of workers. To date, most chemicals and work environments have not been studied for their potential to have damaging effects on the workers' reproductive system. Because of the lack of information, many workers may not be aware that such problems can be related to occupational exposures. Newly industrialized countries such as Republic of Korea have rapidly amassed chemicals and other toxicants that pose health hazards, especially to the reproductive systems of workers. This literature review provides an overview of peer-reviewed literature regarding the teratogenic impact and need for safe handling of chemicals. Literature searches were performed using PubMed, Google Scholar, and ScienceDirect. Search strategies were narrowed based on author expertise and 100 articles were chosen for detailed analysis. A total of 47 articles met prespecified inclusion criteria. The majority of papers contained studies that were descriptive in nature with respect to the Medical Subject Headings (MeSH terms and keywords: “reproductive and heath or hazard and/or workplace or workers or occupations.” In the absence of complete information about the safe occupational handling of chemicals in Republic of Korea (other than a material safety data sheet, this review serves as a valuable reference for identifying and remedying potential gaps in relevant regulations. The review also proposes other public health actions including hazard surveillance and primary prevention activities such as reduction, substitution, ventilation, as well as protective equipment.

  17. Reproductive Toxic Chemicals at Work and Efforts to Protect Workers' Health: A Literature Review.

    Science.gov (United States)

    Rim, Kyung-Taek

    2017-06-01

    A huge number of chemicals are produced and used in the world, and some of them can have negative effects on the reproductive health of workers. To date, most chemicals and work environments have not been studied for their potential to have damaging effects on the workers' reproductive system. Because of the lack of information, many workers may not be aware that such problems can be related to occupational exposures. Newly industrialized countries such as Republic of Korea have rapidly amassed chemicals and other toxicants that pose health hazards, especially to the reproductive systems of workers. This literature review provides an overview of peer-reviewed literature regarding the teratogenic impact and need for safe handling of chemicals. Literature searches were performed using PubMed, Google Scholar, and ScienceDirect. Search strategies were narrowed based on author expertise and 100 articles were chosen for detailed analysis. A total of 47 articles met prespecified inclusion criteria. The majority of papers contained studies that were descriptive in nature with respect to the Medical Subject Headings (MeSH) terms and keywords: "reproductive and heath or hazard and/or workplace or workers or occupations." In the absence of complete information about the safe occupational handling of chemicals in Republic of Korea (other than a material safety data sheet), this review serves as a valuable reference for identifying and remedying potential gaps in relevant regulations. The review also proposes other public health actions including hazard surveillance and primary prevention activities such as reduction, substitution, ventilation, as well as protective equipment.

  18. Chemically activated nanodiamonds for aluminum alloy corrosion protection and monitoring

    Science.gov (United States)

    Hannstein, Inga; Adler, Anne-Katrin; Lapina, Victoria; Osipov, Vladimir; Opitz, Jörg; Schreiber, Jürgen; Meyendorf, Norbert

    2009-03-01

    In the present study, a smart coating for light metal alloys was developed and investigated. Chemically activated nanodiamonds (CANDiT) were electrophoretically deposited onto anodized aluminum alloy AA2024 substrates in order to increase corrosion resistance, enhance bonding properties and establish a means of corrosion monitoring based on the fluorescence behavior of the particles. In order to create stable aqueous CANDiT dispersions suitable for electrophoretic deposition, mechanical milling had to be implemented under specific chemical conditions. The influence of the CANDiT volume fraction and pH of the dispersion on the electrochemical properties of the coated samples was investigated. Linear voltammetry measurements reveal that the chemical characteristics of the CANDiT dispersion have a distinct influence on the quality of the coating. The fluorescence spectra as well as fluorescence excitation spectra of the samples show that corrosion can be easily detected by optical means. Furthermore, an optimization on the basis of "smart" - algorithms for the data processing of a surface analysis by the laser-speckle-method is presented.

  19. Poison politics: a contentious history of consumer protection against dangerous household chemicals in the United States.

    Science.gov (United States)

    Jones, Marian Moser; Benrubi, Isidore Daniel

    2013-05-01

    The history of consumer protection against household poisons presents a key case study of the uniquely American struggle to balance public health and safety with the interests of business. By the late 19th century, package designs, warning labels, and state statutes had formed an uneven patchwork of protective mechanisms against accidental poisonings. As household chemicals proliferated in the early 20th century, physicians concerned with childhood poisonings pressured the federal government to enact legislation mandating warning labels on packaging for these substances. Manufacturers of household chemicals agreed to labeling requirements for caustic poisons but resisted broader regulation. Accidental poisonings of children continued to increase until the enactment of broad labeling and packaging legislation in the 1960s and 1970s. This history suggests that voluntary agreements between government agencies and manufacturers are inadequate to protect consumers against household poisonings and that, in the United States, protective household chemical regulation proceeds in a reactive rather than a precautionary manner.

  20. Functionalized polymer nanofibre membranes for protection from chemical warfare stimulants

    International Nuclear Information System (INIS)

    Ramaseshan, Ramakrishnan; Sundarrajan, Subramanian; Liu, Yingjun; Barhate, R S; Lala, Neeta L; Ramakrishna, S

    2006-01-01

    A catalyst for the detoxification of nerve agents is synthesized from β-cyclodextrin (β-CD) and o-iodosobenzoic acid (IBA). Functionalized polymer nanofibre membranes from PVC polymer are fabricated with β-CD, IBA, a blend of β-CD+IBA, and the synthesized catalyst. These functionalized nanofibres are then tested for the decontamination of paraoxon, a nerve agent stimulant, and it is observed that the stimulant gets hydrolysed. The kinetics of hydrolysis is investigated using UV spectroscopy. The rates of hydrolysis for different organophosphate hydrolyzing agents are compared. The reactivity and amount of adsorption of these catalysts are of higher capacity than the conventionally used activated charcoal. A new design for protective wear is proposed based on the functionalized nanofibre membrane

  1. Chemically armed mercenary ants protect fungus-farming societies

    DEFF Research Database (Denmark)

    Adams, Rachelle Martha Marie; Liberti, Joanito; Illum, Anders A.

    2013-01-01

    guest ants are sufficient to kill raiders that invariably exterminate host nests without a cohabiting guest ant colony. We also show that the odor of guest ants discourages raider scouts from recruiting nestmates to host colonies. Our results imply that Sericomyrmex fungus-growers obtain a net benefit......The ants are extraordinary in having evolved many lineages that exploit closely related ant societies as social parasites, but social parasitism by distantly related ants is rare. Here we document the interaction dynamics among a Sericomyrmex fungus-growing ant host, a permanently associated...... parasitic guest ant of the genus Megalomyrmex, and a raiding agro-predator of the genus Gnamptogenys. We show experimentally that the guest ants protect their host colonies against agro-predator raids using alkaloid venom that is much more potent than the biting defenses of the host ants. Relatively few...

  2. Functionalized polymer nanofibre membranes for protection from chemical warfare stimulants

    Science.gov (United States)

    Ramaseshan, Ramakrishnan; Sundarrajan, Subramanian; Liu, Yingjun; Barhate, R. S.; Lala, Neeta L.; Ramakrishna, S.

    2006-06-01

    A catalyst for the detoxification of nerve agents is synthesized from β-cyclodextrin (β-CD) and o-iodosobenzoic acid (IBA). Functionalized polymer nanofibre membranes from PVC polymer are fabricated with β-CD, IBA, a blend of β-CD+IBA, and the synthesized catalyst. These functionalized nanofibres are then tested for the decontamination of paraoxon, a nerve agent stimulant, and it is observed that the stimulant gets hydrolysed. The kinetics of hydrolysis is investigated using UV spectroscopy. The rates of hydrolysis for different organophosphate hydrolyzing agents are compared. The reactivity and amount of adsorption of these catalysts are of higher capacity than the conventionally used activated charcoal. A new design for protective wear is proposed based on the functionalized nanofibre membrane.

  3. Functionalized polymer nanofibre membranes for protection from chemical warfare stimulants

    Energy Technology Data Exchange (ETDEWEB)

    Ramaseshan, Ramakrishnan [Nanoscience and Nanotechnology Initiative, National University of Singapore, 2 Engineering Drive 3, Singapore 117576, Singapore (Singapore); Sundarrajan, Subramanian [Nanoscience and Nanotechnology Initiative, National University of Singapore, 2 Engineering Drive 3, Singapore 117576, Singapore (Singapore); Liu, Yingjun [Department of Mechanical Engineering, National University of Singapore, 9 Engineering Drive 1, Singapore 117576, Singapore (Singapore); Barhate, R S [Nanoscience and Nanotechnology Initiative, National University of Singapore, 2 Engineering Drive 3, Singapore 117576, Singapore (Singapore); Lala, Neeta L [Nanoscience and Nanotechnology Initiative, National University of Singapore, 2 Engineering Drive 3, Singapore 117576, Singapore (Singapore); Ramakrishna, S [Nanoscience and Nanotechnology Initiative, National University of Singapore, 2 Engineering Drive 3, Singapore 117576, Singapore (Singapore)

    2006-06-28

    A catalyst for the detoxification of nerve agents is synthesized from {beta}-cyclodextrin ({beta}-CD) and o-iodosobenzoic acid (IBA). Functionalized polymer nanofibre membranes from PVC polymer are fabricated with {beta}-CD, IBA, a blend of {beta}-CD+IBA, and the synthesized catalyst. These functionalized nanofibres are then tested for the decontamination of paraoxon, a nerve agent stimulant, and it is observed that the stimulant gets hydrolysed. The kinetics of hydrolysis is investigated using UV spectroscopy. The rates of hydrolysis for different organophosphate hydrolyzing agents are compared. The reactivity and amount of adsorption of these catalysts are of higher capacity than the conventionally used activated charcoal. A new design for protective wear is proposed based on the functionalized nanofibre membrane.

  4. Complete long-term corrosion protection with chemical vapor deposited graphene

    DEFF Research Database (Denmark)

    Yu, Feng; Camilli, Luca; Wang, Ting

    2018-01-01

    Despite numerous reports regarding the potential of graphene for corrosion protection, examples of chemical vapor deposited (CVD) graphene-based anticorrosive coatings able to provide long-term protection (i.e. several months) of metals have so far been absent. Here, we present a polymer-graphene......Despite numerous reports regarding the potential of graphene for corrosion protection, examples of chemical vapor deposited (CVD) graphene-based anticorrosive coatings able to provide long-term protection (i.e. several months) of metals have so far been absent. Here, we present a polymer......-graphene hybrid coating, comprising two single layers of CVD graphene sandwiched by three layers of polyvinyl butyral, which provides complete corrosion protection of commercial aluminum alloys even after 120 days of exposure to simulated seawater. The essential role played by graphene in the hybrid coating...

  5. Attracting predators without falling prey: chemical camouflage protects honeydew-producing treehoppers from ant predation.

    Science.gov (United States)

    Silveira, Henrique C P; Oliveira, Paulo S; Trigo, José R

    2010-02-01

    Predaceous ants are dominant organisms on foliage and represent a constant threat to herbivorous insects. The honeydew of sap-feeding hemipterans has been suggested to appease aggressive ants, which then begin tending activities. Here, we manipulated the cuticular chemical profiles of freeze-dried insect prey to show that chemical background matching with the host plant protects Guayaquila xiphias treehoppers against predaceous Camponotus crassus ants, regardless of honeydew supply. Ant predation is increased when treehoppers are transferred to a nonhost plant with which they have low chemical similarity. Palatable moth larvae manipulated to match the chemical background of Guayaquila's host plant attracted lower numbers of predatory ants than unchanged controls. Although aggressive tending ants can protect honeydew-producing hemipterans from natural enemies, they may prey on the trophobionts under shortage of alternative food resources. Thus chemical camouflage in G. xiphias allows the trophobiont to attract predaceous bodyguards at reduced risk of falling prey itself.

  6. The use of mental models in chemical risk protection: developing a generic workplace methodology.

    Science.gov (United States)

    Cox, Patrick; Niewöhmer, Jörg; Pidgeon, Nick; Gerrard, Simon; Fischhoff, Baruch; Riley, Donna

    2003-04-01

    We adopted a comparative approach to evaluate and extend a generic methodology to analyze the different sets of beliefs held about chemical hazards in the workplace. Our study mapped existing knowledge structures about the risks associated with the use of perchloroethylene and rosin-based solder flux in differing workplaces. "Influence diagrams" were used to represent beliefs held by chemical experts; "user models" were developed from data elicited from open-ended interviews with the workplace users of the chemicals. The juxtaposition of expert and user understandings of chemical risks enabled us to identify knowledge gaps and misunderstandings and to reinforce appropriate sets of safety beliefs and behavior relevant to chemical risk communications. By designing safety information to be more relevant to the workplace context of users, we believe that employers and employees may gain improved knowledge about chemical hazards in the workplace, such that better chemical risk management, self-protection, and informed decision making develop over time.

  7. Chemically armed mercenary ants protect fungus-farming societies

    Science.gov (United States)

    Adams, Rachelle M. M.; Liberti, Joanito; Illum, Anders A.; Jones, Tappey H.; Nash, David R.; Boomsma, Jacobus J.

    2013-01-01

    The ants are extraordinary in having evolved many lineages that exploit closely related ant societies as social parasites, but social parasitism by distantly related ants is rare. Here we document the interaction dynamics among a Sericomyrmex fungus-growing ant host, a permanently associated parasitic guest ant of the genus Megalomyrmex, and a raiding agro-predator of the genus Gnamptogenys. We show experimentally that the guest ants protect their host colonies against agro-predator raids using alkaloid venom that is much more potent than the biting defenses of the host ants. Relatively few guest ants are sufficient to kill raiders that invariably exterminate host nests without a cohabiting guest ant colony. We also show that the odor of guest ants discourages raider scouts from recruiting nestmates to host colonies. Our results imply that Sericomyrmex fungus-growers obtain a net benefit from their costly guest ants behaving as a functional soldier caste to meet lethal threats from agro-predator raiders. The fundamentally different life histories of the agro-predators and guest ants appear to facilitate their coexistence in a negative frequency-dependent manner. Because a guest ant colony is committed for life to a single host colony, the guests would harm their own interests by not defending the host that they continue to exploit. This conditional mutualism is analogous to chronic sickle cell anemia enhancing the resistance to malaria and to episodes in human history when mercenary city defenders offered either net benefits or imposed net costs, depending on the level of threat from invading armies. PMID:24019482

  8. Chemically armed mercenary ants protect fungus-farming societies.

    Science.gov (United States)

    Adams, Rachelle M M; Liberti, Joanito; Illum, Anders A; Jones, Tappey H; Nash, David R; Boomsma, Jacobus J

    2013-09-24

    The ants are extraordinary in having evolved many lineages that exploit closely related ant societies as social parasites, but social parasitism by distantly related ants is rare. Here we document the interaction dynamics among a Sericomyrmex fungus-growing ant host, a permanently associated parasitic guest ant of the genus Megalomyrmex, and a raiding agro-predator of the genus Gnamptogenys. We show experimentally that the guest ants protect their host colonies against agro-predator raids using alkaloid venom that is much more potent than the biting defenses of the host ants. Relatively few guest ants are sufficient to kill raiders that invariably exterminate host nests without a cohabiting guest ant colony. We also show that the odor of guest ants discourages raider scouts from recruiting nestmates to host colonies. Our results imply that Sericomyrmex fungus-growers obtain a net benefit from their costly guest ants behaving as a functional soldier caste to meet lethal threats from agro-predator raiders. The fundamentally different life histories of the agro-predators and guest ants appear to facilitate their coexistence in a negative frequency-dependent manner. Because a guest ant colony is committed for life to a single host colony, the guests would harm their own interests by not defending the host that they continue to exploit. This conditional mutualism is analogous to chronic sickle cell anemia enhancing the resistance to malaria and to episodes in human history when mercenary city defenders offered either net benefits or imposed net costs, depending on the level of threat from invading armies.

  9. Alternative High Performance Polymers for Ablative Thermal Protection Systems

    Science.gov (United States)

    Boghozian, Tane; Stackpoole, Mairead; Gonzales, Greg

    2015-01-01

    Ablative thermal protection systems are commonly used as protection from the intense heat during re-entry of a space vehicle and have been used successfully on many missions including Stardust and Mars Science Laboratory both of which used PICA - a phenolic based ablator. Historically, phenolic resin has served as the ablative polymer for many TPS systems. However, it has limitations in both processing and properties such as char yield, glass transition temperature and char stability. Therefore alternative high performance polymers are being considered including cyanate ester resin, polyimide, and polybenzoxazine. Thermal and mechanical properties of these resin systems were characterized and compared with phenolic resin.

  10. REACTION OF THE FEMALE BODY TO STRESS IN A CHEMICAL PROTECTIVE CLOTHING

    Directory of Open Access Journals (Sweden)

    Jiří SLABOTINSKÝ

    2016-12-01

    Full Text Available This article deals with the reaction of the female body to the use of an insulation chemical protective clothing combined with working – thermal and mental stress to which the female is exposed. The article provides a concise overview of protective chemical clothings and factors affecting their comfort; it describes the regularities corresponding to the physiological reaction, important for the body’s reaction to the use of a chemical protective clothing. Further, the article contains a description of the measurement and evaluation of physiological parameters of non-acclimated women during testing of these clothings and, finally, comparison with the results for males under the same stress which is unfavourable for women.

  11. Performance metrics for the evaluation of hyperspectral chemical identification systems

    Science.gov (United States)

    Truslow, Eric; Golowich, Steven; Manolakis, Dimitris; Ingle, Vinay

    2016-02-01

    Remote sensing of chemical vapor plumes is a difficult but important task for many military and civilian applications. Hyperspectral sensors operating in the long-wave infrared regime have well-demonstrated detection capabilities. However, the identification of a plume's chemical constituents, based on a chemical library, is a multiple hypothesis testing problem which standard detection metrics do not fully describe. We propose using an additional performance metric for identification based on the so-called Dice index. Our approach partitions and weights a confusion matrix to develop both the standard detection metrics and identification metric. Using the proposed metrics, we demonstrate that the intuitive system design of a detector bank followed by an identifier is indeed justified when incorporating performance information beyond the standard detection metrics.

  12. Evaluation of Chemical Warfare Agent Percutaneous Vapor Toxicity: Derivation of Toxicity Guidelines for Assessing Chemical Protective Ensembles.

    Energy Technology Data Exchange (ETDEWEB)

    Watson, A.P.

    2003-07-24

    Percutaneous vapor toxicity guidelines are provided for assessment and selection of chemical protective ensembles (CPEs) to be used by civilian and military first responders operating in a chemical warfare agent vapor environment. The agents evaluated include the G-series and VX nerve agents, the vesicant sulfur mustard (agent HD) and, to a lesser extent, the vesicant Lewisite (agent L). The focus of this evaluation is percutaneous vapor permeation of CPEs and the resulting skin absorption, as inhalation and ocular exposures are assumed to be largely eliminated through use of SCBA and full-face protective masks. Selection of appropriately protective CPE designs and materials incorporates a variety of test parameters to ensure operability, practicality, and adequacy. One aspect of adequacy assessment should be based on systems tests, which focus on effective protection of the most vulnerable body regions (e.g., the groin area), as identified in this analysis. The toxicity range of agent-specific cumulative exposures (Cts) derived in this analysis can be used as decision guidelines for CPE acceptance, in conjunction with weighting consideration towards more susceptible body regions. This toxicity range is bounded by the percutaneous vapor estimated minimal effect (EME{sub pv}) Ct (as the lower end) and the 1% population threshold effect (ECt{sub 01}) estimate. Assumptions of exposure duration used in CPE certification should consider that each agent-specific percutaneous vapor cumulative exposure Ct for a given endpoint is a constant for exposure durations between 30 min and 2 hours.

  13. Patterns of development of unspecific reaction of cells and modification of chemical protection

    International Nuclear Information System (INIS)

    Veksler, A.M.; Korystov, Yu.N.; Kublik, L.N.; Ehjdus, L.Kh.

    1980-01-01

    A study was made of a correlation between radioprotective efficiency of different chemical agents (weak electrolytes) and conditions of treatment. It was demonstrated that the pattern of changes in the protection efficiency, with modification thereof, is similar to that of the development of unspecific reaction and determined by the intracellular concentration of the chemical agents, which, in turn, is function of physicochemical parameters of the substance and pH gradient between cell and medium. With similar intracellular concentration, caffeine-benzoate, thioglicolic acid and caffeine proved to be equally effective, while the protective effect of cysteamine was appreciably higher

  14. Decay Accelerating Factor (CD55) Protects Neuronal Cells from Chemical Hypoxia-Induced Injury

    Science.gov (United States)

    2010-04-09

    Pavlakovic G, Isom GE: Dopaminergic neurotoxicity of cyanide: neurochemical, histological and behavioral characterization. Toxicol Appl Pharmacol...provided the original work is properly cited. ResearchDecay accelerating factor (CD55) protects neuronal cells from chemical hypoxia-induced injury...deposition of C3a/C5a and membrane attack complex (MAC or C5b-9) production. The present study investigates the ability of DAF to protect primary cultured

  15. An Extended Chemical Plant Environmental Protection Game on Addressing Uncertainties of Human Adversaries.

    Science.gov (United States)

    Zhu, Zhengqiu; Chen, Bin; Qiu, Sihang; Wang, Rongxiao; Chen, Feiran; Wang, Yiping; Qiu, Xiaogang

    2018-03-27

    Chemical production activities in industrial districts pose great threats to the surrounding atmospheric environment and human health. Therefore, developing appropriate and intelligent pollution controlling strategies for the management team to monitor chemical production processes is significantly essential in a chemical industrial district. The literature shows that playing a chemical plant environmental protection (CPEP) game can force the chemical plants to be more compliant with environmental protection authorities and reduce the potential risks of hazardous gas dispersion accidents. However, results of the current literature strictly rely on several perfect assumptions which rarely hold in real-world domains, especially when dealing with human adversaries. To address bounded rationality and limited observability in human cognition, the CPEP game is extended to generate robust schedules of inspection resources for inspection agencies. The present paper is innovative on the following contributions: (i) The CPEP model is extended by taking observation frequency and observation cost of adversaries into account, and thus better reflects the industrial reality; (ii) Uncertainties such as attackers with bounded rationality, attackers with limited observation and incomplete information (i.e., the attacker's parameters) are integrated into the extended CPEP model; (iii) Learning curve theory is employed to determine the attacker's observability in the game solver. Results in the case study imply that this work improves the decision-making process for environmental protection authorities in practical fields by bringing more rewards to the inspection agencies and by acquiring more compliance from chemical plants.

  16. An Extended Chemical Plant Environmental Protection Game on Addressing Uncertainties of Human Adversaries

    Science.gov (United States)

    Wang, Rongxiao; Chen, Feiran; Wang, Yiping; Qiu, Xiaogang

    2018-01-01

    Chemical production activities in industrial districts pose great threats to the surrounding atmospheric environment and human health. Therefore, developing appropriate and intelligent pollution controlling strategies for the management team to monitor chemical production processes is significantly essential in a chemical industrial district. The literature shows that playing a chemical plant environmental protection (CPEP) game can force the chemical plants to be more compliant with environmental protection authorities and reduce the potential risks of hazardous gas dispersion accidents. However, results of the current literature strictly rely on several perfect assumptions which rarely hold in real-world domains, especially when dealing with human adversaries. To address bounded rationality and limited observability in human cognition, the CPEP game is extended to generate robust schedules of inspection resources for inspection agencies. The present paper is innovative on the following contributions: (i) The CPEP model is extended by taking observation frequency and observation cost of adversaries into account, and thus better reflects the industrial reality; (ii) Uncertainties such as attackers with bounded rationality, attackers with limited observation and incomplete information (i.e., the attacker’s parameters) are integrated into the extended CPEP model; (iii) Learning curve theory is employed to determine the attacker’s observability in the game solver. Results in the case study imply that this work improves the decision-making process for environmental protection authorities in practical fields by bringing more rewards to the inspection agencies and by acquiring more compliance from chemical plants. PMID:29584679

  17. An Extended Chemical Plant Environmental Protection Game on Addressing Uncertainties of Human Adversaries

    Directory of Open Access Journals (Sweden)

    Zhengqiu Zhu

    2018-03-01

    Full Text Available Chemical production activities in industrial districts pose great threats to the surrounding atmospheric environment and human health. Therefore, developing appropriate and intelligent pollution controlling strategies for the management team to monitor chemical production processes is significantly essential in a chemical industrial district. The literature shows that playing a chemical plant environmental protection (CPEP game can force the chemical plants to be more compliant with environmental protection authorities and reduce the potential risks of hazardous gas dispersion accidents. However, results of the current literature strictly rely on several perfect assumptions which rarely hold in real-world domains, especially when dealing with human adversaries. To address bounded rationality and limited observability in human cognition, the CPEP game is extended to generate robust schedules of inspection resources for inspection agencies. The present paper is innovative on the following contributions: (i The CPEP model is extended by taking observation frequency and observation cost of adversaries into account, and thus better reflects the industrial reality; (ii Uncertainties such as attackers with bounded rationality, attackers with limited observation and incomplete information (i.e., the attacker’s parameters are integrated into the extended CPEP model; (iii Learning curve theory is employed to determine the attacker’s observability in the game solver. Results in the case study imply that this work improves the decision-making process for environmental protection authorities in practical fields by bringing more rewards to the inspection agencies and by acquiring more compliance from chemical plants.

  18. Protecting children from toxic chemicals: putting it on Australia's public health agenda.

    Science.gov (United States)

    Lantz, Sarah

    2013-11-01

    The high volume and widespread use of industrial chemicals, the backlog of internationally untested chemicals, the uptake of synthetic chemicals found in babies in utero, cord blood, and in breast milk, and the lack of a unified and comprehensive regulatory framework all necessitate developing policies that protect the most vulnerable in our society - our children. Australia's failure to do so raises profound intergenerational ethical issues. This article tells a story of international policy, and where Australia is falling down. It demonstrates that we can learn from countries already taking critical steps to reduce the toxic chemical exposure, and that the development of a comprehensive, child-centered chemical regulation framework is central to turning around Australia's failure.

  19. Determination of solvents permeating through chemical protective clothing with a microsensor array.

    Science.gov (United States)

    Park, J; Zellers, E T

    2000-08-01

    The performance of a novel prototype instrument in determining solvents and solvent mixtures permeating through samples of chemical protective clothing (CPC) materials was evaluated. The instrument contains a mini-preconcentrator and an array of three polymer-coated surface-acoustic-wave (SAW) microsensors whose collective response patterns are used to discriminate among multiple permeants. Permeation tests were performed with a 2.54 cm diameter test cell in an open-loop configuration on samples of common glove materials challenged with four individual solvents, three binary mixtures, and two ternary mixtures. Breakthrough times, defined as the times required for the permeation rate to reach a value of 1 microg cm(-2) min(-1), determined by the instrument were within 3 min of those determined in parallel by manual sampling and gas chromatographic analysis. Permeating solvents were recognized (identified) from their response patterns in 59 out of 64 measurements (92%) and their vapor concentrations were quantified to an accuracy of +/- 31% (typically +/- 10%). These results demonstrate the potential for such instrumentation to provide semi-automated field or bench-top screening of CPC permeation resistance.

  20. Mutation induction in rice by radiation combined with chemical protectants and mutagens

    Energy Technology Data Exchange (ETDEWEB)

    Ando, A [Agricultural College, University of Sao Paulo, Sao Paulo (Brazil)

    1970-03-01

    Seeds of the rice variety 'Dourado Precoce' were treated with different combinations of gamma rays, cysteine and EMS or gamma rays, cysteine and dES. Cysteine showed some protection against the effects of gamma radiation and combined gamma-ray + chemical treatments with regard to germination, seedling height and fertility. There are also indications of changes in the spectra of chlorophyll mutations. (author)

  1. The effect of air permeability of chemical protective clothing material on clothing vapour resistance

    NARCIS (Netherlands)

    Havenith, G.; Vuister, R.; Wammes, L.

    1996-01-01

    One of the major problems associated with Chemical Warfare Protective Clothing (CW) is the additional heat load created by the garments. For CW-overgarments, research in the direction of reducing material thickness and thus heat and vapour resistance have not resulted in major improvements. The

  2. Fluid replacement advice during work in fully encapsulated impermeable chemical protective suits

    NARCIS (Netherlands)

    Rubenstein, C.D.; Hartog, E.A. den; Deaton, A.S.; Bogerd, C.P.; Kant, S. de

    2017-01-01

    A major concern for responders to hazardous materials (HazMat) incidents is the heat strain that is caused by fully encapsulated impermeable chemical protective suits. In a research project, funded by the US Department of Defense, the thermal strain experienced when wearing these suits was studied.

  3. Hearing Protection - Needs, Technologies and Performance (Protection de l’ouie - besoins, technologies et resultats)

    Science.gov (United States)

    2010-11-01

    Hearing Protection Selection Considerations 6-1 6.1 Education, Training and Motivation 6-1 6.2 Overprotection 6-1 6.3 Localization and...be carefully chosen to minimize the risk of hearing damage without overprotecting and reducing situational awareness. For many operators the major...performance of the hearing protector itself. 6.2 OVERPROTECTION Hearing protectors must limit the noise exposure for the user, without reducing the

  4. Physical, chemical, and biological properties of radiocerium relevant to radiation protection guidelines

    International Nuclear Information System (INIS)

    Anon.

    1978-01-01

    Present knowledge of the relevant physical, chemical, and biological properties of radiocerium as a basis for establishing radiation protection guidelines is summarized. The first section of the report reviews the chemical and physical properties of radiocerium relative to the biological behavior of internally-deposited cerium and other lanthanides. The second section of the report gives the sources of radiocerium in the environment and the pathways to man. The third section of the report describes the metabolic fate of cerium in several mammalian species as a basis for predicting its metabolic fate in man. The fourth section of the report considers the biomedical effects of radiocerium in light of extensive animal experimentation. The last two sections of the report describe the history of radiation protection guidelines for radiocerium and summarize data required for evaluating the adequacy of current radiation protection guidelines. Each section begins with a summary of the most important findings that follow

  5. Physical Protection System Upgrades - Optimizing for Performance and Cost

    International Nuclear Information System (INIS)

    Hicks, Mary Jane; Bouchard, Ann M.

    1999-01-01

    CPA--Cost and Performance Analysis--is an architecture that supports analysis of physical protection systems and upgrade options. ASSESS (Analytic System and Software for Evaluating Security Systems), a tool for evaluating performance of physical protection systems, currently forms the cornerstone for evaluating detection probabilities and delay times of the system. Cost and performance data are offered to the decision-maker at the systems level and to technologists at the path-element level. A new optimization engine has been attached to the CPA methodology to automate analyses of many combinations (portfolios) of technologies. That engine controls a new analysis sequencer that automatically modifies ASSESS PPS files (facility descriptions), automatically invokes ASSESS Outsider analysis and then saves results for post-processing. Users can constrain the search to an upper bound on total cost, to a lower bound on level of performance, or to include specific technologies or technology types. This process has been applied to a set of technology development proposals to identify those portfolios that provide the most improvement in physical security for the lowest cost to install, operate and maintain at a baseline facility

  6. Impacts of cathodic protection on waste package performance

    International Nuclear Information System (INIS)

    Atkins, J.E.; Lee, J.H.; Andrews, R.W.

    1996-01-01

    The current design concept for a multi-barrier waste container for the potential repository at Yucca Mountain, Nevada, calls for an outer barrier of 100 mm thick corrosion-allowance material (CAM) (carbon steel) and an inner barrier of 20 mm thick corrosion-resistant material (CRM) (Alloy 825). Fulfillment of the NRC subsystem requirements (10 CFR 60.113) of substantially complete containment and controlled release of radionuclides from the engineered barrier system (EBS) will rely mostly upon the robust waste container design, among other EBS components. In the current waste container design, some degree of cathodic protection of CRM will be provided by CAM. This paper discusses a sensitivity case study for the impacts of cathodic protection of the inner barrier by the outer barrier on the performance of waste package

  7. Resistance of Type 5 chemical protective clothing against nanometric airborne particles: Behavior of seams and zipper.

    Science.gov (United States)

    Vinches, Ludwig; Hallé, Stéphane

    2017-12-01

    In the field of dermal protection, the use of chemical protective clothing (CPC) (including coveralls) are considered as the last barrier against airborne engineered nanomaterials (ENM). In the majority of cases, Type 5 CPC, used against solid particles (ISO 13982-1), perform well against ENM. But in a recent study, a penetration level (PL) of up to 8.5% of polydisperse sodium chloride airborne nanoparticles has been measured. Moreover, in all the previous studies, tests were performed on a sample of protective clothing material without seams or zippers. Thus, the potential for permeation through a zipper or seams has not yet been determined, even though these areas would be privileged entry points for airborne ENM. This work was designed to evaluate the PL of airborne ENM through coveralls and specifically the PL through the seams on different parts of the CPC and the zipper. Eight current models of CPC (Type 5) were selected. The samples were taken from places with and without seams and with a zipper. In some cases, a cover strip can be added to the zipper to enhance its sealing. Polydisperse nanoparticles were generated by nebulization of a sodium chloride solution. A penetration cell was developed to expose the sample to airborne nanometric particles. The NaCl particle concentration in number was measured with an ultrafine particle counter and the PL was defined as the downstream concentration divided by the upstream concentration. The results obtained show that the PL increased significantly in the presence of seams and could reach up to 90% depending on the seam's design. Moreover, this study classifies the different types of seams by their resistance against airborne ENM. As for the penetration of airborne NaCl particles through the zipper, the PL was greatly attenuated by the presence of a cover strip, but only for certain models of coveralls. Finally, the values of the pressure drop were directly linked to the type of seam. All of these conclusions provide

  8. Radiation protection - Performance criteria for radiobioassay. Part 1: General principles

    International Nuclear Information System (INIS)

    2001-01-01

    International Standard ISO 12790-1 was prepared by Technical Committee ISO/TC 85, Nuclear energy, Subcommittee SC 2, Radiation protection. ISO 12790 consists of the following parts, under the general title Radiation protection - Performance criteria for radiobioassay: Part 1: General principles; and Part 2: Rationale and specific applications This part of ISO 12790 provides criteria for quality assurance and control, evaluation of performance and the accreditation of radiobioassay service laboratories. Criteria and guidance for direct radiobioassay ( in vivo) and indirect radiobioassay ( in vitro) are given in separate clauses of this part of ISO 12790. This part of ISO 12790 addresses: a) the accuracy of direct ( in vivo) measurements of activity and quantities of selected important radionuclides in test phantoms and indirect ( in vitro) measurements of activity and quantities of selected important radionuclides in test samples; b) methods for determining the minimum detectable amount; c) minimum testing levels and testing ranges; d) requirements for reporting radiobioassay results by service laboratories; e) quality assurance in service laboratories; f) quality control in service laboratories; g) protocol for reporting test evaluations by service laboratories to the testing laboratory; h) default procedures when the service laboratory customer does not specify the performance criteria. The scope of this part of ISO 12790 does not include: a) detailed radiochemical methods for separating radionuclides from biological samples; b) detailed procedures for in vivo and in vitro radioactivity measurements; c) metabolic data and mathematical models for converting radiobioassay results into absorbed dose and dose equivalent; d) procedures for the preparation and distribution of test samples and phantoms by the testing laboratories. Analytical methods for radiobioassay are not currently standardized, but are available in the literature. Guidance for converting

  9. High performance polypyrrole coating for corrosion protection and biocidal applications

    Science.gov (United States)

    Nautiyal, Amit; Qiao, Mingyu; Cook, Jonathan Edwin; Zhang, Xinyu; Huang, Tung-Shi

    2018-01-01

    Polypyrrole (PPy) coating was electrochemically synthesized on carbon steel using sulfonic acids as dopants: p-toluene sulfonic acid (p-TSA), sulfuric acid (SA), (±) camphor sulfonic acid (CSA), sodium dodecyl sulfate (SDS), and sodium dodecylbenzene sulfonate (SDBS). The effect of acidic dopants (p-TSA, SA, CSA) on passivation of carbon steel was investigated by linear potentiodynamic and compared with morphology and corrosion protection performance of the coating produced. The types of the dopants used were significantly affecting the protection efficiency of the coating against chloride ion attack on the metal surface. The corrosion performance depends on size and alignment of dopant in the polymer backbone. Both p-TSA and SDBS have extra benzene ring that stack together to form a lamellar sheet like barrier to chloride ions thus making them appropriate dopants for PPy coating in suppressing the corrosion at significant level. Further, adhesion performance was enhanced by adding long chain carboxylic acid (decanoic acid) directly in the monomer solution. In addition, PPy coating doped with SDBS displayed excellent biocidal abilities against Staphylococcus aureus. The polypyrrole coatings on carbon steels with dual function of anti-corrosion and excellent biocidal properties shows great potential application in the industry for anti-corrosion/antimicrobial purposes.

  10. Protective design of critical infrastructure with high performance concretes

    International Nuclear Information System (INIS)

    Riedel, W.; Nöldgen, M.; Stolz, A.; Roller, C.

    2012-01-01

    Conclusions: High performance concrete constructions will allow innovative design solutions for critical infrastructures. Validation of engineering methods can reside on large and model scale experiments conducted on conventional concrete structures. New consistent impact experiments show extreme protection potential for UHPC. Modern FEM with concrete models and explicit rebar can model HPC and UHPC penetration resistance. SDOF and TDOF approaches are valuable design tools on local and global level. Combination of at least 2 out of 3 design methods FEM – XDOF- EXP allow reliable prediction and efficient innovative designs

  11. Performance Studies for Protection Against Asynchronous Dumps in the LHC

    CERN Document Server

    Kramer, T; Bracco, C; Goddard, B; Meddahi, M

    2010-01-01

    The LHC beam dump system has to safely dispose all beams in a wide energy range of 450 GeV to 7 TeV. A 3 ms abort gap in the beam structure for the switch-on of the extraction kicker field ideally allows a loss-free extraction under normal operating conditions. However, a low number of asynchronous beam aborts is to be expected from reliability calculations and from the first year's operational experience with the beam dump kickers. For such cases, MAD-X simulations including all optics and alignment errors have been performed to determine loss patterns around the LHC as a function of the position of the main protection elements in interaction region six. Special attention was paid to the beam load on the tungsten collimators which protect the triplets in the LHC experimental insertions, and the tracking results compared with semi-analytical numerical estimates. The simulations are also compared to the results of beam commissioning of these protection devices.

  12. Random telegraph signals by alkanethiol-protected Au nanoparticles in chemically assembled single-electron transistors

    International Nuclear Information System (INIS)

    Kano, Shinya; Azuma, Yasuo; Tanaka, Daisuke; Sakamoto, Masanori; Teranishi, Toshiharu; Smith, Luke W.; Smith, Charles G.; Majima, Yutaka

    2013-01-01

    We have studied random telegraph signals (RTSs) in a chemically assembled single-electron transistor (SET) at temperatures as low as 300 mK. The RTSs in the chemically assembled SET were investigated by measuring the source–drain current, using a histogram of the RTS dwell time, and calculating the power spectrum density of the drain current–time characteristics. It was found that the dwell time of the RTS was dependent on the drain voltage of the SET, but was independent of the gate voltage. Considering the spatial structure of the chemically assembled SET, the origin of the RTS is attributed to the trapped charges on an alkanethiol-protected Au nanoparticle positioned near the SET. These results are important as they will help to realize stable chemically assembled SETs in practical applications

  13. The Many Faces of Graphene as Protection Barrier. Performance under Microbial Corrosion and Ni Allergy Conditions

    Science.gov (United States)

    Gentil, Dana; del Campo, Valeria; Henrique Rodrigues da Cunha, Thiago; Henríquez, Ricardo; Garín, Carolina; Ramírez, Cristian; Flores, Marcos; Seeger, Michael

    2017-01-01

    In this work we present a study on the performance of CVD (chemical vapor deposition) graphene coatings grown and transferred on Ni as protection barriers under two scenarios that lead to unwanted metal ion release, microbial corrosion and allergy test conditions. These phenomena have a strong impact in different fields considering nickel (or its alloys) is one of the most widely used metals in industrial and consumer products. Microbial corrosion costs represent fractions of national gross product in different developed countries, whereas Ni allergy is one of the most prevalent allergic conditions in the western world, affecting around 10% of the population. We found that grown graphene coatings act as a protective membrane in biological environments that decreases microbial corrosion of Ni and reduces release of Ni2+ ions (source of Ni allergic contact hypersensitivity) when in contact with sweat. This performance seems not to be connected to the strong orbital hybridization that Ni and graphene interface present, indicating electron transfer might not be playing a main role in the robust response of this nanostructured system. The observed protection from biological environment can be understood in terms of graphene impermeability to transfer Ni2+ ions, which is enhanced for few layers of graphene grown on Ni. We expect our work will provide a new route for application of graphene as a protection coating for metals in biological environments, where current strategies have shown short-term efficiency and have raised health concerns. PMID:29292763

  14. The Many Faces of Graphene as Protection Barrier. Performance under Microbial Corrosion and Ni Allergy Conditions

    Directory of Open Access Journals (Sweden)

    Carolina Parra

    2017-12-01

    Full Text Available In this work we present a study on the performance of CVD (chemical vapor deposition graphene coatings grown and transferred on Ni as protection barriers under two scenarios that lead to unwanted metal ion release, microbial corrosion and allergy test conditions. These phenomena have a strong impact in different fields considering nickel (or its alloys is one of the most widely used metals in industrial and consumer products. Microbial corrosion costs represent fractions of national gross product in different developed countries, whereas Ni allergy is one of the most prevalent allergic conditions in the western world, affecting around 10% of the population. We found that grown graphene coatings act as a protective membrane in biological environments that decreases microbial corrosion of Ni and reduces release of Ni2+ ions (source of Ni allergic contact hypersensitivity when in contact with sweat. This performance seems not to be connected to the strong orbital hybridization that Ni and graphene interface present, indicating electron transfer might not be playing a main role in the robust response of this nanostructured system. The observed protection from biological environment can be understood in terms of graphene impermeability to transfer Ni2+ ions, which is enhanced for few layers of graphene grown on Ni. We expect our work will provide a new route for application of graphene as a protection coating for metals in biological environments, where current strategies have shown short-term efficiency and have raised health concerns.

  15. Performance of evaporators in high level radioactive chemical waste service

    International Nuclear Information System (INIS)

    Jenkins, C.F.

    1997-01-01

    Chemical processing of nuclear fuels and targets at Savannah River Site resulted in generation of millions of gallons of liquid wastes. The wastes were further processed to reduce volume and allow for extended temporary storage of a more concentrated material. Waste evaporators have been a central point for waste reduction for many years. Currently, the transfer and processing of the concentrated wastes for permanent storage requires dilution and results in generation of significant quantities of additional liquid wastes. A new round of volume reduction is required to fit existing storage capacity and to allow for removal of older vessels from service. Evaporator design, performance and repairs are discussed in this report

  16. Protection by caffeine against oxic radiation damage and chemical carcinogens : mechanistic considerations

    International Nuclear Information System (INIS)

    Kesavan, P.C.

    1992-01-01

    There is little doubt that caffeine administered after exposure to UV light enhances the damage to cells and organisms by inhibiting photoreactivation, excision and/or recombinational repair. However, when already present in the system, it affords remarkable protection not only against O 2 -dependent component of radiation damage, but also against chemical carcinogens that require metabolic activation. Possible mechanistic aspects are discussed briefly. (author). 81 refs

  17. Chemical plant protection outlays in vast areas farming at the beginning of 21st century

    Directory of Open Access Journals (Sweden)

    Maria Golinowska

    2009-01-01

    Full Text Available In 2008, several investigations were conducted in the area of chemical plant protection outlays in two vast area farms where simplified system of farming was applied. Analysed outlays consisted of: use of pesticides in kilograms of active substance per 1 ha and real costs of plant protection procedures. Profitability of the outlay was identified with approximate indicator of outlay E1 and E2. The research showed that farm during plant production use from 1 to 10.28 kg AS/ha. Costs of these procedures ranged from 100.50 to 1253.84 PLN/ha depending on the cultivated plant. Profitability of plant protection procedures in wheat and rape cultivation was at the same level in both farms. The highest profitability was reached by maize cultivation.

  18. 78 FR 66384 - Membership of the Merit Systems Protection Board's Performance Review Board

    Science.gov (United States)

    2013-11-05

    ... MERIT SYSTEMS PROTECTION BOARD Membership of the Merit Systems Protection Board's Performance Review Board AGENCY: Merit Systems Protection Board. ACTION: Notice. SUMMARY: Notice is hereby given of the members of the Merit Systems Protection Board's Performance Review Board. DATES: November 5, 2013...

  19. Hmb(off/on) as a switchable thiol protecting group for native chemical ligation.

    Science.gov (United States)

    Qi, Yun-Kun; Tang, Shan; Huang, Yi-Chao; Pan, Man; Zheng, Ji-Shen; Liu, Lei

    2016-05-04

    A new thiol protecting group Hmb(off/on) is described, which has a switchable activity that may be useful in the chemical synthesis of proteins. When placed on the side chain of Cys, Cys(Hmb(off)) is stable to trifluoroacetic acid (TFA) in the process of solid-phase peptide synthesis. When Cys(Hmb(off)) is treated with neutral aqueous buffers, it is cleanly converted to acid-labile Cys(Hmb(on)), which can later be fully deprotected by TFA to generate free Cys. The utility of Cys(Hmb(off/on)) is demonstrated by the chemical synthesis of an erythropoietin segment, EPO[Cys(98)-Arg(166)]-OH through native chemical ligation.

  20. The mechanical integrity and protective performance of silica coatings

    International Nuclear Information System (INIS)

    Crouch, A.G.; Dooley, R.B.

    1976-01-01

    Silica coatings have been developed to reduce the oxidation rates of 9Cr and other steels in high temperature environments. An important aspect of their performance is their ability to withstand the mechanical and thermal strains likely to be encountered in practical applications. This has been examined. Silica-coated 9 Cr steel specimens were deformed in tension and coating failure was detected by scanning electron microscope observations of the oxide stringers which delineated the strain-induced cracks on subsequent exidation. Coating fracture was shown to occur in the strain range 0.27 to 0.45%. The crack separation at constant coating thickness decresed with strain and at constant strain was approximately proportional to the square root of the coating thickness. The implications of these results for the protection of the underlying alloy by a cracked coating are considered. (author)

  1. Ballistic Performance of Porous-Ceramic, Thermal-Protection-Systems

    Science.gov (United States)

    Christiansen, E. L.; Davis, B. A.; Miller, J. E.; Bohl, W. E.; Foreman, C. D.

    2009-01-01

    Porous-ceramic, thermal protection systems are used heavily in current reentry vehicles like the Space Shuttle and are currently being proposed for the next generation of manned spacecraft, Orion. These materials insulate the structural components of a spacecraft against the intense thermal environments of atmospheric reentry. Furthermore, these materials are also highly exposed to space environmental hazards like meteoroid and orbital debris impacts. This paper discusses recent impact testing up to 9 km/s, and the findings of the influence of material equation-of-state on the simulation of the impact event to characterize the ballistic performance of these materials. These results will be compared with heritage models1 for these materials developed from testing at lower velocities. Assessments of predicted spacecraft risk based upon these tests and simulations will also be discussed.

  2. CHEMICALS

    CERN Multimedia

    Medical Service

    2002-01-01

    It is reminded that all persons who use chemicals must inform CERN's Chemistry Service (TIS-GS-GC) and the CERN Medical Service (TIS-ME). Information concerning their toxicity or other hazards as well as the necessary individual and collective protection measures will be provided by these two services. Users must be in possession of a material safety data sheet (MSDS) for each chemical used. These can be obtained by one of several means : the manufacturer of the chemical (legally obliged to supply an MSDS for each chemical delivered) ; CERN's Chemistry Service of the General Safety Group of TIS ; for chemicals and gases available in the CERN Stores the MSDS has been made available via EDH either in pdf format or else via a link to the supplier's web site. Training courses in chemical safety are available for registration via HR-TD. CERN Medical Service : TIS-ME :73186 or service.medical@cern.ch Chemistry Service : TIS-GS-GC : 78546

  3. Improved radiation protection for physicians performing cardiac catheterization

    International Nuclear Information System (INIS)

    Gertz, E.W.; Wisneski, J.A.; Gould, R.G.; Akin, J.R.

    1982-01-01

    Physicians and their assistants performing diagnostic angiography must be concerned with the radiation exposure they receive. The introduction of hemiaxial projections for imaging has increased diagnostic accuracy but has also greatly increased the physicians' exposure to scattered radiation. This increase is especially critical for the eyes and thyroid of the physician who routinely performs these procedures. To reduce such exposure a ceiling-suspended shield (60 x 45 cm), made of 6.4 mm glass with a 19.5 kg/m2 (4 lb/ft2) lead equivalency, was developed. During procedures the shield is interposed between the physician and the region of the patient acting as the source of scattered radiation. The degree of radiation protection to the operator was assessed by measuring the distribution of scattered radiation in the vicinity of the operator with and without the shield. The effectiveness of the shield was determined in the 30 degrees right anterior oblique (RAO), 5 degrees left anterior oblique (LAO), 35 degrees LAO, and 50 degrees LAO-15 degrees cranial angulations. At critical heights such as the level of the eyes and thyroid, scattered radiation levels were reduced by 85% or greater in all angulations. Without interfering with the physician's ability to observe the patient or manipulate the catheter, this shield can significantly reduce the physician's exposure to radiation

  4. Protection against radiation-induced performance decrement in mice

    International Nuclear Information System (INIS)

    Mukherjee, S.K.; Pant, Kanchan; Goel, H.C.; Jain, Viney

    1997-01-01

    Recognizing that there is lack of information on the effects of low-level ionizing radiations and the modifying role of radioprotectors, an attempt has been made in this study to explore the relationship between impairment of spatial learning and low level of radiation exposure. A radial arm maze was utilised to evaluate radiation-induced behavioural alterations and performance decrement in mice. Immediately after whole body exposure to gamma radiation (absorbed dose, 1 Gy) significant perturbations in the learned behaviour of the animals were observed. The regular control movement became irregular and the food consumption time was reduced appreciably (40%). Recovery took place in four days. If diltiazem (7 mg/kg b.w.), a Ca 2+ channel blocker and a radioprotector, was administered i.p. 20-30 min prior to irradiation, radiation-induced behavioural abnormalities were reduced. Mechanisms underlying protection by diltiazem against radiation-induced performance decrement observed in the present study need to be investigated. (author). 23 refs., 2 figs

  5. The use of aldehyde indicators to determine glutaraldehyde and alkaline glutaraldehyde contamination in chemical protective gloves.

    Science.gov (United States)

    Vo, Evanly; Zhuang, Zhenzhen

    2009-07-01

    The aim of this study was to assess the use of aldehyde indicator pads for detection of glutaraldehyde and alkaline glutaraldehyde permeation through chemical protective gloves under simulated in-use conditions. The quantitative analysis of glutaraldehyde permeation through a glove material was determined for Metricide, Wavicide, and 50% glutaraldehyde following a solvent-desorption process and gas chromatographic analysis. All glutaraldehyde solutions exhibited >99% adsorption (including both the glutaraldehyde oligomers of the reaction product and the excess glutaraldehyde) on the pads over the spiking range 0.05-5.0 microL. Breakthrough times for protective gloves were determined using the Thermo-Hand test method, and found to range from 76 to 150, from 170 to 230, and from 232 to 300 min for Metricide, Wavicide, and 50% glutaraldehyde, respectively. Glutaraldehyde recovery was calculated and ranged from 61 to 80% for all glutaraldehyde solutions. The mass of glutaraldehyde in these solutions at the time of breakthrough detection ranged from 17 to 18, from 18 to 19, and from 19 to 20 microg/cm(2) for Wavicide, 50% glutaraldehyde solution, and Metricide, respectively. Aldehyde indicator pads and the Thermo-Hand test method together should find utility in detecting, collecting, and quantitatively analyzing glutaraldehyde permeation samples through chemical protective gloves under simulated in-use conditions.

  6. Green Synthesis of Formulated Zinc Oxide Nanoparticles for Chemical Protection of Skin Care and Related Applications

    Science.gov (United States)

    Koppolu, Ramya

    Nanomaterials have diversified applications based on the unique properties. These nanoparticles and functionalized nanocomposites have been studied in the health care filed. Nanoparticles are mostly used in sunscreens which are a part of human life. These sunscreens consist of titanium dioxide and zinc oxide nanoparticles. Due to the higher band crevices, they help the skin to protect from ultraviolet rays, for instance, ultraviolet B and ultraviolet A. A series of nanostructured zinc oxide nanoparticles were prepared by cost-effective chemical and bioinspired methods and variables were optimized. Highly stable and spherical zinc oxide nanoparticles were formulated by aloe vera ( Aloe barbadensis) plant extract and avocado (Persea americana Mill) fruit extract. The state-of-the-art instrumentation was used to characterize the morphology, elemental composition, and particle size distribution. X-ray diffraction data indicated highly crystalline and ultrafine nanoparticles were obtained from the colloidal methods. The X-ray photoelectron spectroscopy results showed the chemical state of zinc, carbon, and oxygen atoms were well-indexed and are used as fingerprint identification of the elements. Transmission electron microscopy images show the shape of particles were cubic and fiber shape contingent upon the protecting operators and heat treatment conditions. The toxicity studies of zinc oxide nanoparticles were found to cause an increase in nitric oxide, which is protecting against further oxidative stress and appears to be nontoxic.

  7. Is an ecosystem services-based approach developed for setting specific protection goals for plant protection products applicable to other chemicals?

    Science.gov (United States)

    Maltby, Lorraine; Jackson, Mathew; Whale, Graham; Brown, A Ross; Hamer, Mick; Solga, Andreas; Kabouw, Patrick; Woods, Richard; Marshall, Stuart

    2017-02-15

    Clearly defined protection goals specifying what to protect, where and when, are required for designing scientifically sound risk assessments and effective risk management of chemicals. Environmental protection goals specified in EU legislation are defined in general terms, resulting in uncertainty in how to achieve them. In 2010, the European Food Safety Authority (EFSA) published a framework to identify more specific protection goals based on ecosystem services potentially affected by plant protection products. But how applicable is this framework to chemicals with different emission scenarios and receptor ecosystems? Four case studies used to address this question were: (i) oil refinery waste water exposure in estuarine environments; (ii) oil dispersant exposure in aquatic environments; (iii) down the drain chemicals exposure in a wide range of ecosystems (terrestrial and aquatic); (iv) persistent organic pollutant exposure in remote (pristine) Arctic environments. A four-step process was followed to identify ecosystems and services potentially impacted by chemical emissions and to define specific protection goals. Case studies demonstrated that, in principle, the ecosystem services concept and the EFSA framework can be applied to derive specific protection goals for a broad range of chemical exposure scenarios. By identifying key habitats and ecosystem services of concern, the approach offers the potential for greater spatial and temporal resolution, together with increased environmental relevance, in chemical risk assessments. With modifications including improved clarity on terminology/definitions and further development/refinement of the key concepts, we believe the principles of the EFSA framework could provide a methodical approach to the identification and prioritization of ecosystems, ecosystem services and the service providing units that are most at risk from chemical exposure. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights

  8. Performance of a hybrid chemical/mechanical heat pump

    Science.gov (United States)

    Silvestri, John J.; Scaringe, Robert P.; Grzyll, Lawrence R.

    1990-01-01

    The authors present the design and preliminary results of the performance of a hybrid chemical/mechanical, low-lift (20 C) heat pump. Studies have indicated that this heat pump has several advantages over the traditional single fluid vapor compression (reverse Rankine) heat pump. Included in these benefits are: 1) increased COPc due to the approximation of the cycle to the Lorenz cycle and due to the availability of the heat of solution, along with the heat of vaporization, to provide cooling; and 2) ease of variation in system cooling capacity by changing the fluid composition. The system performance is predicted for a variety of refrigerant-absorbent pairs. Cooling capacity is determined for systems operating with ammonia as the refrigerant and lithium nitrate and sodium thiocyanate as the absorbents and also with water as the refrigerant and magnesium chloride, potassium hydroxide, lithium bromide, sodium hydroxide, and sulfuric acid as the absorbents. Early indications have shown that the systems operating with water as the refrigerant operate at 2-4 times the capacity of the ammonia-refrigerant-based systems. Using existing working fluids in the proposed innovative design, a coefficient-of-performance improvement of 21 percent is possible when compared to the best vapor compression systems analyzed.

  9. VALIDATION GUIDELINES FOR LABORATORIES PERFORMING FORENSIC ANALYSIS OF CHEMICAL TERRORISM

    Science.gov (United States)

    The Scientific Working Group on Forensic Analysis of Chemical Terrorism (SWGFACT) has developed the following guidelines for laboratories engaged in the forensic analysis of chemical evidence associated with terrorism. This document provides a baseline framework and guidance for...

  10. Corrosion protection performance of palm and mineral oil media

    International Nuclear Information System (INIS)

    Wan Nik Sani, W.B.; Ani, F.N.; Masjuki, H.H.

    2002-01-01

    In European forest, especially Scandinavian, almost all forest machines are filled with biodegradable fluid. The fluid is of synthetic type. The ratio between the lowest cost of mineral oil and the synthetic fluid is about 1:4. The high cost of this biodegradable fluid can be a major obstacle to be used in developing countries. Malaysia and South East Asia are known for its natural beauties. However, a spill of mineral based oils to their land and seas may result in long term water and soil contamination. Thus crop or agricultural based oil product can provide the solution to this problem. However, considering the demand placed on the oil in service, the service performance such as relation to component compatibility with the crop based oil is crucial to be investigated. The ability of crop based oils to protect and reduce corrosion formation is still unexplored. It is important for each oil to preserve its oxidation stability and remain non-corrosive during service. This paper reports the results of copper corrosion tests. The test includes mass change monitoring, oxide scales and microscopic analysis using Scanning Electron Microscope (SEM). Relative Increase of total acid number and weight loss during copper immersion has proved that metal corrosion in contact with oil was caused by oil degradation that produces acidic compounds. Coppers that were immersed in oil temperature of 60 0 C show that increase of temperature in presence of transition metal induces oil degradation. (Author)

  11. Efficiency and resistance of the artificial oxalate protection treatment on marble against chemical weathering

    International Nuclear Information System (INIS)

    Doherty, B.; Pamplona, M.; Selvaggi, R.; Miliani, C.; Matteini, M.; Sgamellotti, A.; Brunetti, B.

    2007-01-01

    The artificial oxalate protection method was analyzed in laboratory experiments in order to achieve an optimum treatment application and concentration giving rise to its most effective protective nature. Spectroscopic (Fourier transform infrared, Micro-Raman and UV-vis colorimetry), microscopic (scanning electron microscope) and contact-angle analyses were carried out to characterize Carrara marble samples before and after application of the treatment to validate its efficiency. The resistance effects against chemical weathering were subsequently observed in a lab-controlled weak acid rain experiment. An acid spray at pH 5.5, representative of normal rain was used to provoke degrade of natural marble, marble treated with the artificial oxalate protective at concentrations of 0.4 and 5% and marble treated with a commercial organic silicon product. Run-off solutions sampled at timely intervals were tested for any change in pH followed by ion chromatography measurements for the presence of calcium ions in solution. The chromatography results of the oxalate treatment applied at a 5% concentration are analogous to an organic commercial product indicating its validity as a method for the conservation of carbonate substrates conferring protection to stone materials against acid environments

  12. Efficiency and resistance of the artificial oxalate protection treatment on marble against chemical weathering

    Energy Technology Data Exchange (ETDEWEB)

    Doherty, B. [Dipartimento di Chimica, Universita degli Studi di Perugia, via Elce di Sotto, 8, I-60123 Perugia (Italy); Pamplona, M. [Centro de Petrologia e Geoquimica do Instituto Superior Tecnico Universidade Tecnica de Lisboa, Avenida Rovisco Pais, 1049-001 Lisbon (Portugal); Selvaggi, R. [Dipartimento di Chimica, Universita degli Studi di Perugia, via Elce di Sotto, 8, I-60123 Perugia (Italy); Miliani, C. [Istituto CNR di Scienze e Tecnologie Molecolari (ISTM), Dipartimento di Chimica, Universita degli Studi di Perugia, via Elce di Sotto, 8, I-60123 Perugia (Italy)]. E-mail: miliani@thch.unipg.it; Matteini, M. [CNR Istituto, Conservazione e Valorizzazione dei Beni Culturali (ICVBC), Via Madonna del Piano, 10, Edifico C-50019, Florence (Italy); Sgamellotti, A. [Dipartimento di Chimica, Universita degli Studi di Perugia, via Elce di Sotto, 8, I-60123 Perugia (Italy); Istituto CNR di Scienze e Tecnologie Molecolari (ISTM), Dipartimento di Chimica, Universita degli Studi di Perugia, via Elce di Sotto, 8, I-60123 Perugia (Italy); Brunetti, B. [Dipartimento di Chimica, Universita degli Studi di Perugia, via Elce di Sotto, 8, I-60123 Perugia (Italy)

    2007-03-15

    The artificial oxalate protection method was analyzed in laboratory experiments in order to achieve an optimum treatment application and concentration giving rise to its most effective protective nature. Spectroscopic (Fourier transform infrared, Micro-Raman and UV-vis colorimetry), microscopic (scanning electron microscope) and contact-angle analyses were carried out to characterize Carrara marble samples before and after application of the treatment to validate its efficiency. The resistance effects against chemical weathering were subsequently observed in a lab-controlled weak acid rain experiment. An acid spray at pH 5.5, representative of normal rain was used to provoke degrade of natural marble, marble treated with the artificial oxalate protective at concentrations of 0.4 and 5% and marble treated with a commercial organic silicon product. Run-off solutions sampled at timely intervals were tested for any change in pH followed by ion chromatography measurements for the presence of calcium ions in solution. The chromatography results of the oxalate treatment applied at a 5% concentration are analogous to an organic commercial product indicating its validity as a method for the conservation of carbonate substrates conferring protection to stone materials against acid environments.

  13. A multifunctional polymeric nanofilm with robust chemical performances for special wettability

    Science.gov (United States)

    Wang, Yabin; Lin, Feng; Dong, Yaping; Liu, Zhong; Li, Wu; Huang, Yudong

    2016-02-01

    A multifunctional polymeric nanofilm of a triazinedithiolsilane compound, which can protect metallic substrates and activate the corresponding surface simultaneously, is introduced onto a copper mesh surface via facile solution-immersion approaches. The resultant interface exhibits hydrophilic features due to the existence of silanol groups (SiOH) outward and has the potential to act as a superhydrophilic and underwater superoleophobic material. As the polymeric nanofilm atop the copper mesh is modified with long-chain octadecyltrichlorosilane (OTS), the functionalized surface becomes superhydrophobic and superoleophilic. The OTS-modified polymeric nanofilm shows outstanding chemical durability and stability that are seldom concurrently satisfied for a material with special wettability, owing to its inherent architecture. These textures generate high separation efficiency, durable separation capability and excellent thermal stability. The protective ability, originating from the textures of the underlying cross-linked disulfide units (-SS-) and siloxane networks (SiOSi) on the top of the nanofilm, prolongs the chemical durability. The activating capability stemming from the residual SiOH groups improves the chemical stability as a result of the chemical bonds developed by these sites. The significant point of this investigation lies in enlightening us on the fabrication of multifunctional polymeric nanofilms on different metal surfaces using various triazinedithiolsilane compounds, and on the construction of interfaces with controllable wettable performances in demanding research or industrial applications.A multifunctional polymeric nanofilm of a triazinedithiolsilane compound, which can protect metallic substrates and activate the corresponding surface simultaneously, is introduced onto a copper mesh surface via facile solution-immersion approaches. The resultant interface exhibits hydrophilic features due to the existence of silanol groups (SiOH) outward and has

  14. Personal protection during resuscitation of casualties contaminated with chemical or biological warfare agents--a survey of medical first responders.

    Science.gov (United States)

    Brinker, Andrea; Prior, Kate; Schumacher, Jan

    2009-01-01

    The threat of mass casualties caused by an unconventional terrorist attack is a challenge for the public health system, with special implications for emergency medicine, anesthesia, and intensive care. Advanced life support of patients injured by chemical or biological warfare agents requires an adequate level of personal protection. The aim of this study was to evaluate the personal protection knowledge of emergency physicians and anesthetists who would be at the frontline of the initial health response to a chemical/biological warfare agent incident. After institutional review board approval, knowledge of personal protection measures among emergency medicine (n = 28) and anesthetics (n = 47) specialty registrars in the South Thames Region of the United Kingdom was surveyed using a standardized questionnaire. Participants were asked for the recommended level of personal protection if a chemical/biological warfare agent(s) casualty required advanced life support in the designated hospital resuscitation area. The best awareness within both groups was regarding severe acute respiratory syndrome, and fair knowledge was found regarding anthrax, plague, Ebola, and smallpox. In both groups, knowledge about personal protection requirements against chemical warfare agents was limited. Knowledge about personal protection measures for biological agents was acceptable, but was limited for chemical warfare agents. The results highlight the need to improve training and education regarding personal protection measures for medical first receivers.

  15. Field tests for assessing electrical protection performance regarding electromechanical protection relays

    Directory of Open Access Journals (Sweden)

    Luis Alfredo Esteves

    2012-09-01

    Full Text Available This article describes designing and using a series of field tests (such as pick-up test and operating characteristics aimed at ascertaining the correct operation of relays’ electromechanical protection. The characteristic elements involved in adjusting electromechanical protection relays are presented.

  16. Protective properties of wine products and the role of high performance liquid chromatography in the study of these properties

    International Nuclear Information System (INIS)

    Ulyanova, E V; Larionov, O G; Revina, A A; Andrievskaya, D V; Urusova, L M; Fenin, A A

    2013-01-01

    Data on the biologically active substances present in wines and wine products, the methods of their determination, and changes under chemical, radiation and other types of action are generalized. The role of high performance liquid chromatography in the studies of the protective properties of wines is demonstrated. Particular attention is devoted to problems of counterfeiting of wine products and the possibility to reveal it by using amperometric determination of the antioxidant activity. The bibliography includes 117 references

  17. Auditory Localization Performance with Asymmetric Integrated Eye and Ear Protection

    Science.gov (United States)

    2018-03-01

    Scharine, Morgan Domanico, Ashley N Foots, Kim Fluitt, and Timothy J Mermagen Human Research and Engineering Directorate, ARL Morgan Domanico Oak...prototypes. The AIEEP is a tactical communications and protection system (TCAPS) that also provides eye protection. Participants used a laser pointer...Decibels “A-weighted” is the sound pressure level adjusted for the sensitivity of the average human ear. The reference level is the

  18. Regulation and practice of workers' protection from chemical exposures during container handling

    DEFF Research Database (Denmark)

    Nørgaard Fløe Pedersen, Randi; Jepsen, Jørgen Riis; Ádám, Balázs

    2014-01-01

    instructions relate to container handling, the provided information is not sufficiently detailed to conduct safe practice in many aspects. In accordance with the scientific literature, the interviewees estimate that there is a high frequency (5 to 50%) of containers with hazardous chemical exposure......Background: Fumigation of freight containers to prevent spread of pests and off-gassing of freight are sources of volatile chemicals that may constitute significant health risks when released. The aim of the study was to investigate the regulation and practice of container handling in Denmark...... with focus on preventive measures to reduce risk of chemical exposure. Methods: A comprehensive systematic search of scientific literature, legislation and recommendations related to safe work with transport containers from international and Danish regulatory bodies was performed. The practice of handling...

  19. ANALYSIS OF THE MANAGEMENT SYSTEM IN THE FIELD OF ENVIRONMENTAL PROTECTION OF RUSSIAN CHEMICAL COMPANIES

    Directory of Open Access Journals (Sweden)

    Anna Makarov

    2018-03-01

    Full Text Available Since 2007, many chemical industrial companies in the Russian Federation have been actively involved in the Responsible Care® international voluntary program. To implement this program, vast bodies of data on environmental impact assessments needs to be collected. This allows us to analyse the environment-oriented trends in economic and social activities, and to record the achievements and problems in this field. The collected large bodies of data are in many cases heterogeneous, since the report has been a voluntary initiative. To analyse the existing trends in business processes, authors applied the methodology for system analysis of large bodies of data and used their own heuristic approximation algorithm for the treatment of accumulated data. This algorithm gives us the unique possibility of evaluating the performance of both individual chemical companies in the framework of the Responsible Care® program and the Russian chemical industry as a whole.

  20. Performance of Surge Arrester Installation to Enhance Protection

    Directory of Open Access Journals (Sweden)

    Mbunwe Muncho Josephine

    2017-01-01

    Full Text Available The effects of abnormal voltages on power system equipment and appliances in the home have raise concern as most of the equipments are very expensive. Each piece of electrical equipment in an electrical system needs to be protected from surges. To prevent damage to electrical equipment, surge protection considerations are paramount to a well designed electrical system. Lightning discharges are able to damage electric and electronic devices that usually have a low protection level and these are influenced by current or voltage pulses with a relatively low energy, which are induced by lightning currents. This calls for proper designed and configuration of surge arresters for protection on the particular appliances. A more efficient non-linear surge arrester, metal oxide varistor (MOV, should be introduced to handle these surges. This paper shows the selection of arresters laying more emphasis on the arresters for residential areas. In addition, application and installation of the arrester will be determined by the selected arrester. This paper selects the lowest rated surge arrester as it provides insulation when the system is under stress. It also selected station class and distribution class of arresters as they act as an open circuit under normal system operation and to bring the system back to its normal operation mode as the transient voltage is suppressed. Thus, reduces the risk of damage, which the protection measures can be characterized, by the reduction value of the economic loss to an acceptable level.

  1. Effects of rumen-protected tryptophan on performance, nutrient ...

    African Journals Online (AJOL)

    Jane

    2011-06-27

    Jun 27, 2011 ... sources high in rumen-protected Trp (RPT) can be fed to complement the ... collected into plastic containers containing 50 ml of 50% HCl to prevent NH3 .... growth, higher Trp availability could have exerted an effect also on ...

  2. Co3O4 protective coatings prepared by Pulsed Injection Metal Organic Chemical Vapour Deposition

    DEFF Research Database (Denmark)

    Burriel, M.; Garcia, G.; Santiso, J.

    2005-01-01

    of deposition temperature. Pure Co3O4 spinel structure was found for deposition temperatures ranging from 360 to 540 degreesC. The optimum experimental parameters to prepare dense layers with a high growth rate were determined and used to prepare corrosion protective coatings for Fe-22Cr metallic interconnects......Cobalt oxide films were grown by Pulsed Injection Metal Organic Chemical Vapour Deposition (PI-MOCVD) using Co(acac)(3) (acac=acetylacetonate) precursor dissolved in toluene. The structure, morphology and growth rate of the layers deposited on silicon substrates were studied as a function......, to be used in Intermediate Temperature Solid Oxide Fuel Cells. (C) 2004 Elsevier B.V. All rights reserved....

  3. Corrosion Protection of Al Alloys for Aircraft by Coatings With Advanced Properties and Enhanced Performance

    National Research Council Canada - National Science Library

    Bierwagen, Gordon; Croll, Stuart; Webster, Dean; Tallman, Dennis; Huo, Qun; Allahar, Brian; Su, Quan; Bonitz, Verena; Fernando, Dilhan; Wang, Duhua

    2007-01-01

    The report presents research that addresses research performed at NDSU for environmentally compliant corrosion protection in coatings systems of greatly extended lifetimes for present and future aircraft...

  4. Protection against genetic hazards from environmental chemical mutagens: experience with ionizing radiation

    International Nuclear Information System (INIS)

    Sankaranarayanan, K.

    1977-01-01

    In radiation protection, the recurrent theme is, and always has been, dose limitation whether it is for occupational workers, individual members of the public or the population as a whole. The key words are 'dose' and 'limitation'. The quantitative system of dose limitation has been achieved because of a number of conceptual developments in our understanding of the mechanism of radiation action, development of radiation dosimetry, the accumulation of a vast body of quantitative information on dose-effect relationships and the effects of various biological and physical variables that affect these relationships of data on patterns and levels of exposures likely to be encountered to make estimates of the effects expected to result from such exposures, and balancing of risks to society against the benefits derived, the latter a matter of informed judgement. The philosophy has always been to avoid all unnecessary exposures and to limit the necessary exposures (justified by the benefits expected) to as low a level as reasonably achievable, social and economic factors being taken into acccount. The introduction of the concept that the system of dose limitation to the population should be based on genetic risks has stressed the need for careful planning to ensure that our genetic heritage is not endangered. Transfer of this knowledge to the field of chemical protection is discussed. (Auth.)

  5. Chemical composition and biological evaluation of Physalis peruviana root as hepato-renal protective agent.

    Science.gov (United States)

    El-Gengaihi, Souad E; Hassan, Emad E; Hamed, Manal A; Zahran, Hanan G; Mohammed, Mona A

    2013-03-01

    This study was designed to investigate the potential of Physalis peruviana root as a functional food with hepato-renal protective effects against fibrosis. The chemical composition of the plant root suggested the presence of alkaloids, withanolides and flavonoids. Five compounds were isolated and their structures elucidated by different spectral analysis techniques. One compound was isolated from the roots: cuscohygrine. The biological evaluation was conducted on different animal groups; control rats, control treated with ethanolic root extract, CCl(4) group, CCl(4) treated with root extract, and CCl(4) treated with silymarin as a standard herbal drug. The evaluation used the oxidative stress markers malondialdehyde (MDA), superoxide dismutase (SOD), and nitric oxide (NO). The liver function indices; aspartate and alanine aminotransferases (AST & ALT), alkaline phosphatase (ALP), gamma glutamyl transferase (GGT), bilirubin, and total hepatic protein were also estimated. Kidney disorder biomarkers; creatinine, urea, and serum protein were also evaluated. The results suggested safe administration, and improvement of all the investigated parameters. The liver and kidney histopathological analysis confirmed the results. In conclusion, P. peruviana succeeded in protecting the liver and kidney against fibrosis. Further studies are needed to discern their pharmacological applications and clinical uses.

  6. Damage and Performance Assessment of Protective Coatings on Turbine Blades

    OpenAIRE

    Pokluda, Jaroslav; Kianicová, Marta

    2010-01-01

    Protective coatings on blades serve as physical barriers between the underlying substrate and the outer environment. This article presents an overview of damage mechanisms leading to failure of all basic types of coatings (diffusion, overlay and thermal barrier) on turbine blades of aircraft engines during service. Although a special emphasize is devoted to destructive effects of thermo-mechanical fatigue and overheating, the severe effects of hot corrosion, oxidation and erosion effects are ...

  7. Protective effect of conditioning agents on Afro-ethnic hair chemically treated with thioglycolate-based straightening emulsion.

    Science.gov (United States)

    Dias, Tania Cristina de Sá; Baby, André Rolim; Kaneko, Telma Mary; Velasco, Maria Valéria Robles

    2008-06-01

    Straightening is a chemical process by which excessively curly hair is straightened in an irreversible way. Generally, products are formulated as emulsions with high pH value (9.0-12.0), which, after applied on hair, cause considerable damage, making it dry and fragile. This research work evaluated the protective effect of lauryl PEG/PPG-18/18 methicone, cyclopentasiloxane (and) PEG-12 dimethicone cross-polymer, jojoba oil, and aqua (and) cystine bis-PG propyl silanetriol, as conditioning agents, on Afro-ethnic hair locks treated with thioglycolate-based straightening emulsions by protein loss, combability, and traction to rupture. Standard Afro-ethnic hair locks were prepared following a protocol for straightening emulsion application. Considering the assays performed, the addition of conditioning agents to the straightening emulsion with ammonium thioglycolate benefited the hair fiber, thus diminishing protein loss, protecting the hair thread, and improving resistance to breakage. Jojoba oil and lauryl PEG/PPG-18/18 methicone were the conditioning agents that presented the best results. Straightening emulsions with ammonium thioglycolate containing aqua (and) cystine bis-PG propyl silanetriol and cyclopentasiloxane (and) PEG-12 dimethicone cross-polymer were the ones that provided higher breakage resistance of the thread.

  8. Hygienic assessment of professional risk for worker, involved in application of pesticides and tank mixtures in chemical protection of strawberry

    Directory of Open Access Journals (Sweden)

    Zinchenko T.I.

    2016-12-01

    Full Text Available When using tank mixtures and pesticides in chemical crop protection systems there exists danger of simultaneous or sequential action of ingredients. It was established that the combined potential risk of the harmful effects of Torero SC preparation on workers is 0.11-0.30 arb.units, Switch 62.5 WG – 0.054-0,065 arb.units, tank mixture 1 – 0.26-0.51 arb.units, tank mixture 2 – 0.26-0.49 arb.units correspondently and does not exceed the allowable value of risk (<1. The combined risk in sequential application of components of chemical protection system of strawberry exceeds allowable values of risk and is 0.954-2.02 arb.units. Ways of occupational risk decrease were proposed and regulations of safe application of tank mixtures and pesticides in chemical protection of strawberry were substantiated.

  9. A survey on selection, use, maintenance, and management of chemical protective gloves at workplaces in Japan.

    Science.gov (United States)

    Kabe, Isamu; Tsuruoka, Hiroko; Kochi, Takeshi; Koga, Yasuo; Eguchi, Masafumi; Matsui, Tomomi; Ito, Rie; Tokujitani, Yoko; Miyauchi, Hiroyuki; Tanaka, Shigeru

    2017-10-05

    The aim of this study was to survey the selection, use, and maintenance of chemical protective gloves (CPGs) at real workplaces. Subjects comprised 817 workers using CPGs at seven domestic manufacturing plants in Japan. We administered an anonymous questionnaire survey comprising the following aspect related to CPGs: environment of use, conditions of use, method of selection, knowledge/awareness pertaining to their use, method of use, precautionary measures associated with their use, maximum time of use, and maintenance. We compared responses provided by management staff and field workers. Chi square test was used for the analysis. Respondents included 661 (80.9%) manufacturing workers, 121 (14.8%) managers or supervisors, and 35 (4.3%) others. In total, 70.5% organic solvents, 28.9% acid or/and alkali, 18.1% dust, and 10.3% carcinogenic substances were the chemical substances handled using CPGs. The reason for deciding to wear CPGs was "the use of chemical substances" for 46.5%, "notice in safety data sheet (SDS) " for 29.8%, and "management staffs' guidance" for 21.4% respondents. "The grasp of chemical substances" was 70.1% (91.1% excluding "not applicable" ). "Warning of caution on skin and eyes" was indicated by 69.5% (91.0%) and "educational reasons for use of CPGs" was accepted by 68.1% (90.7%) respondents. On the other hand, the rate of responses such as "obtaining permeability test results of target substances" and "mixed substances are selected considering substances with short permeation time" was 25.2% (38.4%) and 29.2% (48.4%), respectively. The rate of "yes" as a response in the item concerning "permeation test" was low. On comparing the response provided by the management staff and field workers, the rate of "the permeation test result of the target substance was obtained" was 27.7% for management staff and 41.2% for field workers (p = 0.022). Regarding the cuffs of CPGs, the rate of "to fold back and to prevent sagging" and "mounted with tape" were

  10. An Analysis on the Moisture and Thermal Protective Performance of Firefighter Clothing Based on Different Layer Combinations and Effect of Washing on Heat Protection and Vapour Transfer Performance

    Directory of Open Access Journals (Sweden)

    Ozgur Atalay

    2015-01-01

    Full Text Available Fabric assemblies for firefighting clothing have been tested for heat protection and comfort. The constituent materials and fabric structures have been specifically selected and tailored for firefighters’ clothing. In order to do this, four types of outer shell fabrics, four types of moisture barrier fabrics, and four types of heat barriers with different weights and material compositions were used to make a multilayered fabric assembly. Heat transfer (flame, heat transfer (radiant, and water vapour resistance tests were conducted according to the latest EN469 test standard which also recommends washing tests. These tests reveal that material content and material brand have considerable effect on the required performance levels of heat protection. In addition, while washing tests have improved water vapor transfer properties, they have a deteriorating effect on heat protection performance. Considering heat protection and moisture comfort properties, the optimal assemblies are thereby identified.

  11. Chemical Protection Testing of Sorbent-Based Air Purification Components (APCs)

    Science.gov (United States)

    2016-06-24

    handling and storing the chemical materials of interest. Testing facilities intending to use chemical warfare agents (CWAs) and nontraditional agents...handling, and decontamination capabilities for research, development, test, and evaluation (RDT&E) quantities of chemical agents. Chemical agent...and decontaminated IAW the test plan and all test documentation will be archived. All recoverable chemical test materials will be accounted for and

  12. Capacity shortfalls hinder the performance of marine protected areas globally

    Science.gov (United States)

    Gill, David A.; Mascia, Michael B.; Ahmadia, Gabby N.; Glew, Louise; Lester, Sarah E.; Barnes, Megan; Craigie, Ian; Darling, Emily S.; Free, Christopher M.; Geldmann, Jonas; Holst, Susie; Jensen, Olaf P.; White, Alan T.; Basurto, Xavier; Coad, Lauren; Gates, Ruth D.; Guannel, Greg; Mumby, Peter J.; Thomas, Hannah; Whitmee, Sarah; Woodley, Stephen; Fox, Helen E.

    2017-03-01

    Marine protected areas (MPAs) are increasingly being used globally to conserve marine resources. However, whether many MPAs are being effectively and equitably managed, and how MPA management influences substantive outcomes remain unknown. We developed a global database of management and fish population data (433 and 218 MPAs, respectively) to assess: MPA management processes; the effects of MPAs on fish populations; and relationships between management processes and ecological effects. Here we report that many MPAs failed to meet thresholds for effective and equitable management processes, with widespread shortfalls in staff and financial resources. Although 71% of MPAs positively influenced fish populations, these conservation impacts were highly variable. Staff and budget capacity were the strongest predictors of conservation impact: MPAs with adequate staff capacity had ecological effects 2.9 times greater than MPAs with inadequate capacity. Thus, continued global expansion of MPAs without adequate investment in human and financial capacity is likely to lead to sub-optimal conservation outcomes.

  13. Ballistic Performance of Porous-Ceramic, Thermal Protection Systems

    Science.gov (United States)

    Miller, J. E.; Bohl, W. E.; Christiansen, Eric C.; Davis, B. A.; Foreman, C. D.

    2011-01-01

    Porous-ceramic, thermal protection systems are used heavily in current reentry vehicles like the Orbiter, and they are currently being proposed for the next generation of US manned spacecraft, Orion. These systems insulate reentry critical components of a spacecraft against the intense thermal environments of atmospheric reentry. Additionally, these materials are highly exposed to space environment hazards like solid particle impacts. This paper discusses impact studies up to 10 km/s on 8 lb/cu ft alumina-fiber-enhanced-thermal-barrier (AETB8) tiles coated with a toughened-unipiece-fibrous-insulation/ reaction-cured-glass layer (TUFI/RCG). A semi-empirical, first principals impact model that describes projectile dispersion is described that provides excellent agreement with observations over a broad range of impact velocities, obliquities and projectile materials. Model extensions to look at the implications of greater than 10 GPa equation of state is also discussed. Predicted penetration probabilities for a vehicle visiting the International Space Station is 60% lower for orbital debris and 95% lower for meteoroids with this model compared to an energy scaled approach.

  14. Performance predictions for solar-chemical convertors by computer simulation

    Energy Technology Data Exchange (ETDEWEB)

    Luttmer, J.D.; Trachtenberg, I.

    1985-08-01

    A computer model which simulates the operation of Texas Instruments solar-chemical convertor (SCC) was developed. The model allows optimization of SCC processes, material, and configuration by facilitating decisions on tradeoffs among ease of manufacturing, power conversion efficiency, and cost effectiveness. The model includes various algorithms which define the electrical, electrochemical, and resistance parameters and which describ the operation of the discrete components of the SCC. Results of the model which depict the effect of material and geometric changes on various parameters are presented. The computer-calculated operation is compared with experimentall observed hydrobromic acid electrolysis rates.

  15. In situ synthesis, electrochemical and quantum chemical analysis of an amino acid-derived ionic liquid inhibitor for corrosion protection of mild steel in 1M HCl solution

    International Nuclear Information System (INIS)

    Kowsari, E.; Arman, S.Y.; Shahini, M.H.; Zandi, H.; Ehsani, A.; Naderi, R.; PourghasemiHanza, A.; Mehdipour, M.

    2016-01-01

    Highlights: • Electrochemical analysis of effectiveness of an amino acid-derived ionic liquid inhibitor. • Quantum chemical analysis of effectiveness of an amino acid-derived ionic liquid inhibitor. • Finding correlation between electrochemical analysis and quantum chemical analysis. - Abstract: In this study, an amino acid-derived ionic liquid inhibitor, namely tetra-n-butyl ammonium methioninate, was synthesized and the role this inhibitor for corrosion protection of mild steel exposed to 1.0 M HCl was investigated using electrochemical, quantum and surface analysis. By taking advantage of potentiodynamic polarization, the inhibitory action of tetra-n-butyl ammonium methioninate was found to be mainly mixed-type with dominant anodic inhibition. The effectiveness of the inhibitor was also indicated using electrochemical impedance spectroscopy (EIS). Moreover, to provide further insight into the mechanism of inhibition, electrochemical noise (EN) and quantum chemical calculations of the inhibitor were performed.

  16. The overpressure protection for the chemical reactors: the batch-size approach

    International Nuclear Information System (INIS)

    Dellavedova, M.; Gigante, L.; Lunghi, A.; Pasturenzi, C.; Cardillo, P.; Gerosa, N.P.; Rota, R.

    2008-01-01

    Small and medium enterprises (SMEs) main feature is to run batch and semi-batch processes, working on job orders. They generally have multi propose reactors with an emergency relief system (ERS) already installed. These are normally sized when the reactor is designed, assuming as worst incidental scenario a single phase vapour flow generated by a fire developed outside the apparatus. These assumptions can lead to a big underestimation of the vent area if the actual flow is two-phase and besides generated by a runaway reaction. ERS sizing is particularly hazardous and complex for small mills, as for example fine chemicals and pharmaceutical companies. These factories have usually narrow financial and personal resources, moreover they often use fast processes turnovers. In many cases a complete safety study or the replacement of the ERS is not possible and it can lead to not sustainable costs. The batch-size approach is focused on discontinuous process conditions: aim of this approach is to find the reactor fill level that can lead a vapour single phase flow whether an incident occurs, this condition is considered safe that the ERS installed on the reactor can protect the plant from explosions [it

  17. Influence of the chemical composition on steel casting performance

    Directory of Open Access Journals (Sweden)

    Roney Eduardo Lino

    2017-01-01

    Full Text Available Improving the quality of steel and the steelmaking process has been a matter of routine for metallurgical engineers and steelmaking companies in a demanding market for quality products at highly competitive price. The chemical and temperature adjustment are made during the secondary refining process, as well as the inclusion modification required to product quality, and also the demand for castability accuracy. Continuous casting process is the most used solidification casting process, in which the flow of pouring liquid metal through the submerged entry nozzle is assured by the correct temperature and the formation of liquid inclusion in the casting temperature. Thermocalc and CEQCSI were the software used in this work to assess the effect of carbon, silicon and sulphur in the castability window of the aluminium vs calcium phase diagrams. They have proved to be highly suitable and effective and the results showed that the chemical elements used directly affected the position of the castability window of carbon steel. An analysis of a 0.2%C billet sample using Scanning Electron Microscopy showed that there is a great heterogeneity of inclusions in aluminium-killed and calcium-treated steel.

  18. Morphine tolerance offers protection from radiogenic performance deficits

    International Nuclear Information System (INIS)

    Mickley, G.A.; Stevens, K.E.; Burrows, J.M.; White, G.A.; Gibbs, G.L.

    1983-01-01

    When rats are exposed to a sufficiently large dose of ionizing radiation they exhibit lethargy, hypokinesia, and deficits in performance. These and other behavioral changes parallel those often observed in this species after a large dose of morphine. Since the release of endogenous opiates has been implicated in some stress reactions, we sought to determine if they might play a part in radiogenic behavioral deficits. Rats were trained to criterion on a signaled avoidance task. Some subjects were then implanted with a pellet containing 75 mg of morphine. Other animals received placebo implants. Over a number of days, morphine tolerance was evaluated by measurement of body temperature changes. Prior to 2500 rad 60 Co exposure or sham irradiation, morphine (or placebo) pellets were removed. Twenty-four hours later rats were retested to assess their performance on the avoidance task. Morphine-tolerant subjects performed significantly better than the irradiated placebo-implanted group and no differently than morphine-tolerant/sham-irradiated animals. Morphine tolerance seems to provide a degree of behavioral radiation resistance. These data are consistent with the hypothesis that endogenous opiate hyperexcretion may play some part in the behavioral deficits often observed after irradiation

  19. Chemical products toxicological tests performed on lake and river fish

    International Nuclear Information System (INIS)

    Teulon, F.; Simeon, C.

    1966-01-01

    The volume and toxical values of industrial and urban effluents are growing higher and therefore acute or chronic pollution hazard is proportionally increased. Hence it is necessary to determine the effluent components minimum lethal dose for fish (one hour or six hours according to applicable standards). The following tests are described in this report: toxicity of some chemical products, tested individually (sodium, sulphate, sodium chloride, sodium fluoride, etc...); toxicity of some metal ions (Al 3+ , Fe ++ , Fe 3+ , Pb ++ , etc...); toxicity of certain mixed compounds for various fish species (sun perch, tench, gold fish, roach, gudgeon, bleak). The test results obtained represent local values and may be used for reference and as a general basis for other investigation and calculation of the effluents data when released. (author) [fr

  20. Performance of a written radiation protection inspection of nonstationary gamma radiography users

    International Nuclear Information System (INIS)

    Hoehne, M.

    1986-01-01

    A questionare has been developed for controlling users of nonstationary gamma radiography devices. It is aimed at obtaining information about the weak points according to radiation protection and to give guidance in performing such controls by the respective radiation protection officers. The questionare is included

  1. Performance assessment of select covers and disposal cell compliance with EPA [Environmental Protection Agency] groundwater standards

    International Nuclear Information System (INIS)

    1989-06-01

    This document describes the technical approach to the assessment of the performance of a full component topslope cover, three sideslope covers, and hence the way in which a Uranium Mill Tailings Remedial Action (UMTRA) Project disposal cell complies with the US Environmental Protection Agency (EPA) groundwater protection standards. 4 refs

  2. Evaluation of Personal Chemical Vapor Protection for Patrol and Tactical Law Enforcement

    National Research Council Canada - National Science Library

    Fedele, Paul D; Lake, William L; Arca, Victor J; Marshall, Stephen M; Mitchell, David B

    2002-01-01

    ... functions in law enforcement. Various Level C, impermeable and charcoal impregnated, vapor-absorptive, air-permeable protective clothing ensembles, worn with the MSA Millenium respiratory protective mask/butyl hood, and seven-mil...

  3. Corrosion protection performance of waterborne epoxy coatings containing self-doped polyaniline nanofiber

    International Nuclear Information System (INIS)

    Qiu, Shihui; Chen, Cheng; Cui, Mingjun; Li, Wei; Zhao, Haichao; Wang, Liping

    2017-01-01

    Highlights: • Self-dopedpolyaniline (SPANi) with good conductivity and dispersibility in water was copolymerized by aniline and its derivative. • Environmental friendly SPANi/epoxy composite coating with remarkable anti-corrosion performance was prepared. • The corrosion product of pure epoxy or composite coating was characterized by X-ray diffraction pattern and scanning electron microscope (SEM). - Abstract: Self-doped sulfonated polyaniline (SPANi) nanofiber was synthesized by the copolymerization of 2-aminobenzenesulfonic acid (ASA) and aniline via a rapid mixing polymerization approach. The chemical structure of SPANi was investigated by the Fourier-transform infrared (FT-IR), Raman, X-ray photoelectron spectroscopy (XPS), UV–vis spectra and X-ray diffraction (XRD) pattern. The as-prepared SPANi nanofibers had 45 nm average diameter and length up to 750 nm as measured by scanning electron microscope (SEM) and transmission electron microscope (TEM). The self-doped SPANi nanofiber possessed excellent aqueous solubility, good conductivity (0.11 S/cm) and reversible redox activity, making it suitable as a corrosion inhibitor for waterborne coatings. The prepared SPANi/waterborne epoxy composite coatings exhibited remarkably improved corrosion protection compared with pure waterborne epoxy coating as proved by the polarization curves and electrochemical impedance spectroscopy (EIS). The passivation effect of SPANi nanofiber and the corrosion products beneath the epoxy coatings immersed in 3.5% NaCl solution as a function of time were also investigated in this study.

  4. Corrosion protection performance of waterborne epoxy coatings containing self-doped polyaniline nanofiber

    Energy Technology Data Exchange (ETDEWEB)

    Qiu, Shihui [Key Laboratory of Marine Materials and Related Technologies, Zhejiang Key Laboratory of Marine Materials and Protective Technologies, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo, 315201 (China); Faculty of Materials Science and Chemical Engineering, Ningbo University, Ningbo, 315211 (China); Chen, Cheng; Cui, Mingjun [Key Laboratory of Marine Materials and Related Technologies, Zhejiang Key Laboratory of Marine Materials and Protective Technologies, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo, 315201 (China); Li, Wei [Faculty of Materials Science and Chemical Engineering, Ningbo University, Ningbo, 315211 (China); Zhao, Haichao, E-mail: zhaohaichao@nimte.ac.cn [Key Laboratory of Marine Materials and Related Technologies, Zhejiang Key Laboratory of Marine Materials and Protective Technologies, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo, 315201 (China); Wang, Liping, E-mail: wangliping@nimte.ac.cn [Key Laboratory of Marine Materials and Related Technologies, Zhejiang Key Laboratory of Marine Materials and Protective Technologies, Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, Ningbo, 315201 (China)

    2017-06-15

    Highlights: • Self-dopedpolyaniline (SPANi) with good conductivity and dispersibility in water was copolymerized by aniline and its derivative. • Environmental friendly SPANi/epoxy composite coating with remarkable anti-corrosion performance was prepared. • The corrosion product of pure epoxy or composite coating was characterized by X-ray diffraction pattern and scanning electron microscope (SEM). - Abstract: Self-doped sulfonated polyaniline (SPANi) nanofiber was synthesized by the copolymerization of 2-aminobenzenesulfonic acid (ASA) and aniline via a rapid mixing polymerization approach. The chemical structure of SPANi was investigated by the Fourier-transform infrared (FT-IR), Raman, X-ray photoelectron spectroscopy (XPS), UV–vis spectra and X-ray diffraction (XRD) pattern. The as-prepared SPANi nanofibers had 45 nm average diameter and length up to 750 nm as measured by scanning electron microscope (SEM) and transmission electron microscope (TEM). The self-doped SPANi nanofiber possessed excellent aqueous solubility, good conductivity (0.11 S/cm) and reversible redox activity, making it suitable as a corrosion inhibitor for waterborne coatings. The prepared SPANi/waterborne epoxy composite coatings exhibited remarkably improved corrosion protection compared with pure waterborne epoxy coating as proved by the polarization curves and electrochemical impedance spectroscopy (EIS). The passivation effect of SPANi nanofiber and the corrosion products beneath the epoxy coatings immersed in 3.5% NaCl solution as a function of time were also investigated in this study.

  5. Chemical gel barriers as low-cost alternative to containment and in situ cleanup of hazardous wastes to protect groundwater

    International Nuclear Information System (INIS)

    1997-01-01

    Chemical gel barriers are being considered as a low-cost alternative for containment and in situ cleanup of hazardous wastes to protect groundwater. Most of the available gels in petroleum application are non-reactive and relative impermeable, providing a physical barriers for all fluids and contaminants. However, other potential systems can be envisioned. These systems could include gels that are chemically reactive and impermeable such that most phase are captured by the barriers but the contaminants could diffuse through the barriers. Another system that is chemically reactive and permeable could have potential applications in selectivity capturing contaminants while allowing water to pass through the barriers. This study focused on chemically reactive and permeable gel barriers. The gels used in experiment are DuPont LUDOX SM colloidal silica gel and Pfizer FLOPAAM 1330S hydrolyzed polyacrylamide (HPAM) gel

  6. Influence of dust and mud on the optical, chemical, and mechanical properties of a pv protective glass.

    Science.gov (United States)

    Yilbas, Bekir Sami; Ali, Haider; Khaled, Mazen M; Al-Aqeeli, Nasser; Abu-Dheir, Numan; Varanasi, Kripa K

    2015-10-30

    Recent developments in climate change have increased the frequency of dust storms in the Middle East. Dust storms significantly influence the performances of solar energy harvesting systems, particularly (photovoltaic) PV systems. The characteristics of the dust and the mud formed from this dust are examined using various analytical tools, including optical, scanning electron, and atomic force microscopies, X-ray diffraction, energy spectroscopy, and Fourier transform infrared spectroscopy. The adhesion, cohesion and frictional forces present during the removal of dry mud from the glass surface are determined using a microtribometer. Alkali and alkaline earth metal compounds in the dust dissolve in water to form a chemically active solution at the glass surface. This solution modifies the texture of the glass surface, thereby increasing the microhardness and decreasing the transmittance of the incident optical radiation. The force required to remove the dry mud from the glass surface is high due to the cohesive forces that result from the dried mud solution at the interface between the mud and the glass. The ability altering the characteristics of the glass surface could address the dust/mud-related limitations of protective surfaces and has implications for efficiency enhancements in solar energy systems.

  7. Usefulness of non-lead aprons in radiation protection for physicians performing interventional procedures

    International Nuclear Information System (INIS)

    Zuguchi, M.; Chida, K.; Taura, M.; Inaba, Y.; Ebata, A.; Yamada, S.

    2008-01-01

    At present, interventional radiology (IVR) tends to involve long procedures (long radiation duration), and physicians are near to the source of scattered radiation. Hence, shielding is critical in protecting physicians from radiation. Protective aprons and additional lead-shielding devices, such as table-side lead drapes, are important means of protecting the physician from scattered radiation. The purpose of this study was to evaluate whether non-lead aprons are effective in protecting physicians from radiation during IVR procedures. In this study, the radiation protection effects of commercially available protective lead and non-lead aprons, when exposed to diagnostic X rays, are compared. The performance of these non-lead and lead aprons was similar for scattered X rays at tube voltages of 60-120 kV. Properly designed non-lead aprons are thus more suitable for physicians because they weigh ∼20% less than the lead aprons, and are non-toxic. (authors)

  8. Feasibility Study of Economics and Performance of Wind Turbine Generators at the Newport Indiana Chemical Depot Site

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Joseph Owen [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mosey, Gail [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2013-11-01

    The U.S. Environmental Protection Agency (EPA), in accordance with the RE-Powering America's Land initiative, selected the Newport Indiana Chemical Depot site in Newport, Indiana, for a feasibility study of renewable energy production. The National Renewable Energy Laboratory (NREL) was contacted to provide technical assistance for this project. The purpose of this report is to assess the sitefor possible wind turbine electrical generator installation and estimate the cost, performance, and site impacts of different wind energy options. In addition, the report recommends financing options that could assist in the implementation of a wind system at the site.

  9. Chemical protection of bacteria and cultured mammalian cells by sulfur--containing compounds

    Energy Technology Data Exchange (ETDEWEB)

    Antoku, S [Hiroshima Univ. (Japan). Research Inst. for Nuclear Medicine and Biology

    1975-03-01

    Protection by sulfur-containing compounds was studied using bacteria E. coli Bsub(H) and cultured mouse leukemic cells, L 5178 Y. The protective mechanisms are discussed. The dose reduction factors of non-sulfhydryl compounds observed in the bacteria were the same as those observed in mammalian cells, and the protective activity of these compounds was proportional to their reaction rates with hydroxyl radicals. On the other hand, sulfhydryl compounds, with the exception of glutathione, offered a much greater protection than was anticipated from their radical scavenging activity. From studies under anoxia, the protection of cysteine was explained by its OH scavenging and competition with oxygen. In addition, for MEA, protection against the direct action of radiation was suggested. This was supported by the significant protection in the frozen state.

  10. IMPROVING THE ENVIRONMENTAL PERFORMANCE OF CHEMICAL PROCESSES THROUGH THE USE OF INFORMATION TECHNOLOGY

    Science.gov (United States)

    Efforts are currently underway at the USEPA to develop information technology applications to improve the environmental performance of the chemical process industry. These efforts include the use of genetic algorithms to optimize different process options for minimal environmenta...

  11. Performance Characteristic of Cold Recycled Mixture with Asphalt Emulsion and Chemical Additives

    Directory of Open Access Journals (Sweden)

    Shaowen Du

    2015-01-01

    Full Text Available Three types of chemical additives were used to modify asphalt emulsion recycled mixture. These chemical additives include composite Portland cement (CPC, hydrated lime (HL, and a combination of hydrated lime and ground-granulated blast-furnace slag (GGBF. The influence of different additives on the recycled mixture performance was investigated by volumetric and strength tests, moisture susceptibility test, rutting resistance test, and low temperature bending test. To better understand its performance characteristic, the microstructure images of the recycled mixture were observed by environmental scanning electron microscope (ESEM. Test results demonstrate that the performance improvement of the emulsion recycled mixture depends on the types and content of chemical additives. Several recommendations are presented for the selection of chemical materials. Based on ESEM image analysis, the interface bonding mechanism is proposed to explain the performance characteristic of the recycled mixture with asphalt emulsion and cementitious materials.

  12. How Do I Know? A Guide to the Selection of Personal Protective Equipment for Use in Responding to A Release of Chemical Warfare Agents

    Energy Technology Data Exchange (ETDEWEB)

    Foust, C.B.

    1999-05-01

    An incident involving chemical warfare agents requires a unique hazardous materials (HAZMAT) response. As with an HAZMAT event, federal regulations prescribe that responders must be protected from exposure to the chemical agents. But unlike other HAZMAT events, special considerations govern selection of personal protective equipment (PPE). PPE includes all clothing, respirators and monitoring devices used to respond to a chemical release. PPE can differ depending on whether responders are military or civilian personnel.

  13. Technological advancements for the detection of and protection against biological and chemical warfare agents.

    Science.gov (United States)

    Eubanks, Lisa M; Dickerson, Tobin J; Janda, Kim D

    2007-03-01

    There is a growing need for technological advancements to combat agents of chemical and biological warfare, particularly in the context of the deliberate use of a chemical and/or biological warfare agent by a terrorist organization. In this tutorial review, we describe methods that have been developed both for the specific detection of biological and chemical warfare agents in a field setting, as well as potential therapeutic approaches for treating exposure to these toxic species. In particular, nerve agents are described as a typical chemical warfare agent, and the two potent biothreat agents, anthrax and botulinum neurotoxin, are used as illustrative examples of potent weapons for which countermeasures are urgently needed.

  14. Are the performance overestimates given by boys with ADHD self-protective?

    Science.gov (United States)

    Ohan, Jeneva L; Johnston, Charlotte

    2002-06-01

    Tested the self-protective hypothesis that boys with attention deficit hyperactivity disorder (ADHD) overestimate their performance to protect a positive self-image. We examined the impact of performance feedback on the social and academic performance self-perceptions of 45 boys with and 43 boys without ADHD ages 7 to 12. Consistent with the self-protective hypothesis, positive feedback led to increases in social performance estimates in boys without ADHD but to decreases in estimates given by boys with ADHD. This suggests that boys with ADHD can give more realistic self-appraisals when their self-image has been bolstered. In addition, social performance estimates in boys with ADHD were correlated with measures of self-esteem and positive presentation bias. In contrast, for academic performance estimates, boys in both groups increased their performance estimates after receiving positive versus average or no feedback, and estimates were not correlated with self-esteem or social desirability for boys with ADHD. We conclude that the self-protective hypothesis can account for social performance overestimations given by boys with ADHD but that other factors may better account for their academic performance overestimates.

  15. Review on technical issues influencing the performance of chemical barriers of TRU waste repository

    International Nuclear Information System (INIS)

    Fujita, Tomonari; Sugiyama, Daisuke; Tsukamoto, Masaki; Yokoyama, Hayaichi

    1997-01-01

    Studies of technical issues influencing the performance assessment of TRU waste disposal which is occurred from the nuclear fuel reprocessing were reviewed in related to the development of safety analysis method. Especially, the chemical containment was investigated as a key barrier to radionuclide migration. TRU waste including long-lived radionuclides need long-term performance assessment which could be assumed only by the chemical barrier. The description of technical issues concerned with the performance of TRU waste repository has been divided into the following categories: long-term degradation of cementitious materials as engineered barrier for radionuclide migration, effect of colloids, organic macromolecules and organic degradation products on chemical behavior of radionuclides, gas generation by corrosion of metallic wastes, and effects of microbial activity. Preliminary performance assessment indicated that important factors affecting performance of chemical barriers in near-field were the distribution coefficient and the solubility of radionuclides in near-field groundwater. Therefore, it was identified that key issues associated with performance of chemical barrier were evaluation of (a) the long-term change of distribution coefficient of cementitious material through the degradation under repository condition and (b) chemical speciation change of radionuclides such as increase of solubility by the presence of colloidal-size materials. (author)

  16. Biophysical Characteristics of Chemical Protective Ensemble With and Without Body Armor

    Science.gov (United States)

    2015-07-01

    agility and mobility to complete mission-essential tasks. Nevertheless, the bulk, weight, and encapsulation associated with these protective ensembles...compromises mobility , agility, situational awareness, and thermoregulation. Thermal strain management during military training and operations...Corner BD, & Paquette S. Investigation of Air Gaps Entrapped in Protective Clothing System. Fire and Materials, 26(3), 121-126, 2002. 15. Song G

  17. Study of skin model and geometry effects on thermal performance of thermal protective fabrics

    Science.gov (United States)

    Zhu, Fanglong; Ma, Suqin; Zhang, Weiyuan

    2008-05-01

    Thermal protective clothing has steadily improved over the years as new materials and improved designs have reached the market. A significant method that has brought these improvements to the fire service is the NFPA 1971 standard on structural fire fighters’ protective clothing. However, this testing often neglects the effects of cylindrical geometry on heat transmission in flame resistant fabrics. This paper deals with methods to develop cylindrical geometry testing apparatus incorporating novel skin bioheat transfer model to test flame resistant fabrics used in firefighting. Results show that fabrics which shrink during the test can have reduced thermal protective performance compared with the qualities measured with a planar geometry tester. Results of temperature differences between skin simulant sensors of planar and cylindrical tester are also compared. This test method provides a new technique to accurately and precisely characterize the thermal performance of thermal protective fabrics.

  18. Assessment of patient radiation protection in external radiotherapy departments after inspections performed by the ASN 2008

    International Nuclear Information System (INIS)

    Franchi, Vincent; Marchal, Carole

    2009-10-01

    This report proposes an assessment of patient radiation protection in external radiotherapy. It is based on inter-regional syntheses of inspections performed by the ASN in external radiotherapy departments during 2008. It addresses 6 main themes related to patient radiation protection: human and material resources, organisation of medical physics, training in patient radiation protection, mastering of equipment (maintenance, internal quality controls of medical devices), safety and care quality management (formalization of the patient care process and definition of responsibilities, patient identity control, treatment preparation, and treatment execution), and risk management (a priori risk analysis, declaration, recording and internal processing of dysfunctions, improvements of care quality and safety management system)

  19. Fault Transient Analysis and Protection Performance Evaluation within a Large-scale PV Power Plant

    Directory of Open Access Journals (Sweden)

    Wen Jinghua

    2016-01-01

    Full Text Available In this paper, a short-circuit test within a large-scale PV power plant with a total capacity of 850MWp is discussed. The fault currents supplied by the PV generation units are presented and analysed. According to the fault behaviour, the existing protection coordination principles with the plant are considered and their performances are evaluated. Moreover, these protections are examined in simulation platform under different operating situations. A simple measure with communication system is proposed to deal with the foreseeable problem about the current protection scheme in the PV power plant.

  20. Performance Evaluation of Fusing Protected Fingerprint Minutiae Templates on the Decision Level

    Directory of Open Access Journals (Sweden)

    Raymond N. J. Veldhuis

    2012-04-01

    Full Text Available In a biometric authentication system using protected templates, a pseudonymous identifier is the part of a protected template that can be directly compared. Each compared pair of pseudonymous identifiers results in a decision testing whether both identifiers are derived from the same biometric characteristic. Compared to an unprotected system, most existing biometric template protection methods cause to a certain extent degradation in biometric performance. Fusion is therefore a promising way to enhance the biometric performance in template-protected biometric systems. Compared to feature level fusion and score level fusion, decision level fusion has not only the least fusion complexity, but also the maximum interoperability across different biometric features, template protection and recognition algorithms, templates formats, and comparison score rules. However, performance improvement via decision level fusion is not obvious. It is influenced by both the dependency and the performance gap among the conducted tests for fusion. We investigate in this paper several fusion scenarios (multi-sample, multi-instance, multi-sensor, multi-algorithm, and their combinations on the binary decision level, and evaluate their biometric performance and fusion efficiency on a multi-sensor fingerprint database with 71,994 samples.

  1. Performance Evaluation of Fusing Protected Fingerprint Minutiae Templates on the Decision Level

    Science.gov (United States)

    Yang, Bian; Busch, Christoph; de Groot, Koen; Xu, Haiyun; Veldhuis, Raymond N. J.

    2012-01-01

    In a biometric authentication system using protected templates, a pseudonymous identifier is the part of a protected template that can be directly compared. Each compared pair of pseudonymous identifiers results in a decision testing whether both identifiers are derived from the same biometric characteristic. Compared to an unprotected system, most existing biometric template protection methods cause to a certain extent degradation in biometric performance. Fusion is therefore a promising way to enhance the biometric performance in template-protected biometric systems. Compared to feature level fusion and score level fusion, decision level fusion has not only the least fusion complexity, but also the maximum interoperability across different biometric features, template protection and recognition algorithms, templates formats, and comparison score rules. However, performance improvement via decision level fusion is not obvious. It is influenced by both the dependency and the performance gap among the conducted tests for fusion. We investigate in this paper several fusion scenarios (multi-sample, multi-instance, multi-sensor, multi-algorithm, and their combinations) on the binary decision level, and evaluate their biometric performance and fusion efficiency on a multi-sensor fingerprint database with 71,994 samples. PMID:22778583

  2. The Unsuspected Roles of Chemistry in Nuclear Power Plants: Special Chemical Technologies for Enhanced Safety and Increased Performance

    International Nuclear Information System (INIS)

    Sempere Belda, Luis

    2008-01-01

    The plant's chemists main responsibility is the establishment and monitoring of an adequate water chemistry to minimize corrosion and in PWRs, to control the neutron flux. But this is by no means the only way in which chemical applications contribute to the performance and safety of a NPP during its entire life: The use of special coatings and treatment protects the plant's components from aggressive environmental conditions. The chemical scale removal in steam generators improves the power output of aging plants, helping even to achieve permissions for NPP life extension. The use of special adhesives can replace welding in complicated or high-dose areas, even underwater. And chemical decontamination is used to remove activity from the components of the primary circuit prior to maintenance or replacement works in order to decrease the radiation exposure of the plant's personnel, employing revolutionary methods of waste minimization to limit the amount of generated radioactive waste to a minimum. The AREVA Group, in its pursue of excellence in all stages of the nuclear cycle, has devoted years of research and development to be able to provide the most advanced technological solutions in this field. The awareness of the existing possibilities will help present and future nuclear professionals, chemists and non-chemists alike, to benefit from the years of experience and continuous development in chemical technologies at the service of the nuclear industry. (authors)

  3. The Unsuspected Roles of Chemistry in Nuclear Power Plants: Special Chemical Technologies for Enhanced Safety and Increased Performance

    Energy Technology Data Exchange (ETDEWEB)

    Sempere Belda, Luis [AREVA NP GmbH, An AREVA and SIEMENS Company, P.O. Box 1109, Erlangen (Germany)

    2008-07-01

    The plant's chemists main responsibility is the establishment and monitoring of an adequate water chemistry to minimize corrosion and in PWRs, to control the neutron flux. But this is by no means the only way in which chemical applications contribute to the performance and safety of a NPP during its entire life: The use of special coatings and treatment protects the plant's components from aggressive environmental conditions. The chemical scale removal in steam generators improves the power output of aging plants, helping even to achieve permissions for NPP life extension. The use of special adhesives can replace welding in complicated or high-dose areas, even underwater. And chemical decontamination is used to remove activity from the components of the primary circuit prior to maintenance or replacement works in order to decrease the radiation exposure of the plant's personnel, employing revolutionary methods of waste minimization to limit the amount of generated radioactive waste to a minimum. The AREVA Group, in its pursue of excellence in all stages of the nuclear cycle, has devoted years of research and development to be able to provide the most advanced technological solutions in this field. The awareness of the existing possibilities will help present and future nuclear professionals, chemists and non-chemists alike, to benefit from the years of experience and continuous development in chemical technologies at the service of the nuclear industry. (authors)

  4. Project W-314 Polyurea Special Protective Coating (SPC) Test Plan Chemical Compatibility and Physical Characteristics Testing

    International Nuclear Information System (INIS)

    MAUSER, R.W.

    2001-01-01

    This Test Plan outlines the testing to be done on the Special Protective Coating (SPC) Polyurea which includes: Tank Waste Compatibility, Decontamination Factor Testing, and Adhesion Strength Testing after a sample has been exposed to Radiation

  5. Animal experiments to investigate biological-chemical radiation protection and the therapy of radiolesions

    International Nuclear Information System (INIS)

    Brueckner, V.

    1974-01-01

    The influence of a combined therapy of radiation protection agents and erythropoetin on the radiation-induced suppression of erythropoiesis in mice is studied with the aid of the radioiron utilization test. After whole-body irradiation with 500 R, the erythropoietic system is so severely affected that erythropoetin application alone does not yield any results. AET (significant) and Cysteamin (insignificant), on the other hand, protect the bone marrow to a certain degree. The protected bone marrow provides a better base for erythropoetin therapy than the bone marrow of the irradiated and unprotected animals. Compared to the application of radiation protection agents alone, the combined therapy with AET and erythropoetin increases the radioiron incorporation in the erythrocytes by 7.5% while the therapy with Cysteamin and erythropoetin results in a 19.3% increase. In spite of these methods, however, the radioiron incorporation rate of the control animals was not reached. (BSC/AK) [de

  6. Design of a High Performance Green-Mode PWM Controller IC with Smart Sensing Protection Circuits

    Directory of Open Access Journals (Sweden)

    Shen-Li Chen

    2014-08-01

    Full Text Available A design of high performance green-mode pulse-width-modulation (PWM controller IC with smart sensing protection circuits for the application of lithium-ion battery charger (1.52 V ~ 7.5 V is investigated in this paper. The protection circuits architecture of this system mainly bases on the lithium battery function and does for the system design standard of control circuit. In this work, the PWM controller will be with an automatic load sensing and judges the system operated in the operating mode or in the standby mode. Therefore, it reduces system’s power dissipation effectively and achieves the saving power target. In the same time, many protection sensing circuits such as: (1 over current protection (OCP and under current protection (UCP, (2 over voltage protection (OVP and under voltage protection (UVP, (3 loading determintion and short circuit protection (SCP, (4 over temperature protection (OTP, (5 VDD surge-spiking protection are included. Then, it has the characteristics of an effective monitoring the output loading and the harm prevention as a battery charging. Eventually, this green-mode pulse-width-modulation (PWM controller IC will be that the operation voltage is 3.3 V, the operation frequency is 0.98 MHz, and the output current range is from 454 mA to 500 mA. Meanwhile, the output convert efficiency is range from 74.8 % to 91 %, the power dissipation efficiency in green-mode is 25 %, and the operation temperature range is between -20 0C ~ 114 0C.

  7. Performance Test of Core Protection and Monitoring Algorithm with DLL for SMART Simulator Implementation

    International Nuclear Information System (INIS)

    Koo, Bonseung; Hwang, Daehyun; Kim, Keungkoo

    2014-01-01

    A multi-purpose best-estimate simulator for SMART is being established, which is intended to be used as a tool to evaluate the impacts of design changes on the safety performance, and to improve and/or optimize the operating procedure of SMART. In keeping with these intentions, a real-time model of the digital core protection and monitoring systems was developed and the real-time performance of the models was verified for various simulation scenarios. In this paper, a performance test of the core protection and monitoring algorithm with a DLL file for the SMART simulator implementation was performed. A DLL file of the simulator application code was made and several real-time evaluation tests were conducted for the steady-state and transient conditions with simulated system variables. A performance test of the core protection and monitoring algorithms for the SMART simulator was performed. A DLL file of the simulator version code was made and several real-time evaluation tests were conducted for various scenarios with a DLL file and simulated system variables. The results of all test cases showed good agreement with the reference results and some features caused by algorithm change were properly reflected to the DLL results. Therefore, it was concluded that the SCOPS S SIM and SCOMS S SIM algorithms and calculational capabilities are appropriate for the core protection and monitoring program in the SMART simulator

  8. Effects of chemical equilibrium on turbine engine performance for various fuels and combustor temperatures

    Science.gov (United States)

    Tran, Donald H.; Snyder, Christopher A.

    1992-01-01

    A study was performed to quantify the differences in turbine engine performance with and without the chemical dissociation effects for various fuel types over a range of combustor temperatures. Both turbojet and turbofan engines were studied with hydrocarbon fuels and cryogenic, nonhydrocarbon fuels. Results of the study indicate that accuracy of engine performance decreases when nonhydrocarbon fuels are used, especially at high temperatures where chemical dissociation becomes more significant. For instance, the deviation in net thrust for liquid hydrogen fuel can become as high as 20 percent at 4160 R. This study reveals that computer central processing unit (CPU) time increases significantly when dissociation effects are included in the cycle analysis.

  9. High-Performance Liquid Chromatography in the Undergraduate Chemical Engineering Laboratory

    Science.gov (United States)

    Frey, Douglas D.; Guo, Hui; Karnik, Nikhila

    2013-01-01

    This article describes the assembly of a simple, low-cost, high-performance liquid chromatography (HPLC) system and its use in the undergraduate chemical engineering laboratory course to perform simple experiments. By interpreting the results from these experiments students are able to gain significant experience in the general method of…

  10. Chemical monitoring strategy for the assessment of advanced water treatment plant performance.

    Science.gov (United States)

    Drewes, J E; McDonald, J A; Trinh, T; Storey, M V; Khan, S J

    2011-01-01

    A pilot-scale plant was employed to validate the performance of a proposed full-scale advanced water treatment plant (AWTP) in Sydney, Australia. The primary aim of this study was to develop a chemical monitoring program that can demonstrate proper plant operation resulting in the removal of priority chemical constituents in the product water. The feed water quality to the pilot plant was tertiary-treated effluent from a wastewater treatment plant. The unit processes of the AWTP were comprised of an integrated membrane system (ultrafiltration, reverse osmosis) followed by final chlorination generating a water quality that does not present a source of human or environmental health concern. The chemical monitoring program was undertaken over 6 weeks during pilot plant operation and involved the quantitative analysis of pharmaceuticals and personal care products, steroidal hormones, industrial chemicals, pesticides, N-nitrosamines and halomethanes. The first phase consisted of baseline monitoring of target compounds to quantify influent concentrations in feed waters to the plant. This was followed by a period of validation monitoring utilising indicator chemicals and surrogate measures suitable to assess proper process performance at various stages of the AWTP. This effort was supported by challenge testing experiments to further validate removal of a series of indicator chemicals by reverse osmosis. This pilot-scale study demonstrated a simplified analytical approach that can be employed to assure proper operation of advanced water treatment processes and the absence of trace organic chemicals.

  11. Protective efficacy of combined administration of lipopolysaccharide of E. coli and chemical radioprotectors under conditions of prolonged irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Misustova, J; Hosek, B; Sikulova, J; Kautska, J; Fjodorov, B A

    1984-07-01

    We investigated the protective effectiveness of the lipopolysaccharide of E. coli (LPS) in a combination with a mixture of chemical radioprotectors in female mice of the strain H at various radiation dose rates. LPS in a dose of 0.08 mg per kg of body mass was administered 1, 3, or 24 hours prior to irradiation, the radioprotective mixture (cystamine 90 mgxkg/sup -1/+5-methoxytryptamine 15 mgxkg/sup -1/) was administered 10 minutes before irradiation. Dose rates of 612 mGyxmin/sup -1/ (irradiation time 10 to 15 minutes), 38 mGyxmin/sup -1/ (3 to 4 hours), and 8.2 mGyxmin/sup -1/ (27 to 29 hours) were used. The results showed that isolated administrations of LPS or of the radioprotective mixture increased the resistance of the mice against prolonged irradiation; the combined administration even enhanced the efficacy of the radioprotective action. However, this efficacy depended on the magnitude of the dose rate. At dose rates higher than 38 mGyxmin/sup -1/ the effectiveness of the chemical protection prevailed, whereas at lower dose rates the biological and especially the combined protection became effective. We demonstrate a slight pyrogenic effect of LPS by measuring oxygen consumption and changes in some parameters of the hematopoiesis.

  12. Molecular modeling for the design of novel performance chemicals and materials

    CERN Document Server

    Rai, Beena

    2012-01-01

    Molecular modeling (MM) tools offer significant benefits in the design of industrial chemical plants and material processing operations. While the role of MM in biological fields is well established, in most cases MM works as an accessory in novel products/materials development rather than a tool for direct innovation. As a result, MM engineers and practitioners are often seized with the question: ""How do I leverage these tools to develop novel materials or chemicals in my industry?"" Molecular Modeling for the Design of Novel Performance Chemicals and Materials answers this important questio

  13. Simulating Mobility of Chemical Contaminants from Unconventional Gas Development for Protection of Water Resources

    Science.gov (United States)

    Kanno, C.; Edlin, D.; Borrillo-Hutter, T.; McCray, J. E.

    2014-12-01

    Potential contamination of ground water and surface water supplies from chemical contaminants in hydraulic fracturing fluids or in natural gas is of high public concern. However, quantitative assessments have rarely been conducted at specific energy-producing locations so that the true risk of contamination can be evaluated. The most likely pathways for contamination are surface spills and faulty well bores that leak production fluids directly into an aquifer. This study conducts fate and transport simulations of the most mobile chemical contaminants, based on reactivity to subsurface soils, degradation potential, and source concentration, to better understand which chemicals are most likely to contaminate water resources, and to provide information to planners who wish to be prepared for accidental releases. The simulations are intended to be most relevant to the Niobrara shale formation.

  14. Chemical oil-spill dispersants: evaluation of three laboratory procedures for estimating performance

    International Nuclear Information System (INIS)

    Clayton, J.R.; Marsden, P.

    1992-09-01

    The report presents data from studies designed to evaluate characteristics of selected bench-scale test methods for estimating performance of chemical agents for dispersing oil from surface slicks into an underlying water column. In order to mitigate the effect of surface slicks with chemical dispersant agents, however, an on-scene coordinator must have information and an understanding of performance characteristics for available dispersant agents. Performance of candidate dispersant agents can be estimated on the basis of laboratory testing procedures that are designed to evaluate performance of different agents. Data presented in the report assist in the evaluation of candidate test methods for estimating performance of candidate dispersant agents. Three test methods were selected for evaluating performance: the currently accepted Revised Standard EPA test, Environmental Canada's Swirling Flask test, and the IFP-Dilution test

  15. Combined radiation and chemical method of protection against organic pests of wooden objects

    International Nuclear Information System (INIS)

    Santar, I.; Urban, J.

    Radiation disinsection and fungus removal are considered to be two suitable methods of protecting wooden historical objects. A dose of 500 Gy (from a 60 Co source) has no harmful effect on oil or tempera polychromy, on inlays or other surface finishes of such objects. Radiation disinsection does not protect the treated article from future insect attack and is therefore supplemented with a preservation procedure in which a solution of pentachlorophenol and tributyl tin oxide in an aromatic solvent is used. A unit for preservation by radiation at Roztoky near Prague is described. (H.S.)

  16. Chemical overcharge protection of lithium and lithium-ion secondary batteries

    Science.gov (United States)

    Abraham, Kuzhikalail M.; Rohan, James F.; Foo, Conrad C.; Pasquariello, David M.

    1999-01-01

    This invention features the use of redox reagents, dissolved in non-aqueous electrolytes, to provide overcharge protection for cells having lithium metal or lithium-ion negative electrodes (anodes). In particular, the invention features the use of a class of compounds consisting of thianthrene and its derivatives as redox shuttle reagents to provide overcharge protection. Specific examples of this invention are thianthrene and 2,7-diacetyl thianthrene. One example of a rechargeable battery in which 2,7-diacetyl thianthrene is used has carbon negative electrode (anode) and spinet LiMn.sub.2 O.sub.4 positive electrode (cathode).

  17. Environmental Performance and Financing Decisions Impact on Sustainable Financial Development of Chinese Environmental Protection Enterprises

    Directory of Open Access Journals (Sweden)

    Kai Quan Zhang

    2017-12-01

    Full Text Available Environmental protection firms need to improve their ability to access financing while maintaining good economic performance under mounting environmental pressures. After the integration of trade-off and stakeholder theories, we have constructed a number of mathematical models to investigate the relationship among financing decisions, environmental performance (EP, and economic performance. Unbalanced panel data from environmental protection companies listed on Chinese stock exchanges from 2007 to 2016 were collected and analyzed. Our results have confirmed that debt financing has a significant impact on short- and long-term economic performance. Firms prefer long-term debt over short-term debt to improve their financial sustainability. Internal financing is positively related to performance because the cost of financing is lower. Environmental performance can cause extra financial burden in the short run, but will improve stakeholder relations and profitability in the long run. Our study suggests that environmental performance affects the relationship between financing decisions and economic performance. When EP initiatives are high, debt financing has a greater negative influence on short-term performance, and the effect on long-term performance is mitigated. High EP also reduces the impact of internal financing on performance.

  18. Cost and performance analysis of physical protection systems - a case study

    International Nuclear Information System (INIS)

    Hicks, M.J.; Snell, M.S.; Sandoval, J.S.; Potter, C.S.

    1998-01-01

    Design and analysis of physical protection systems requires (1) identification of mission critical assets; (2) identification of potential threats that might undermine mission capability; (3) identification of the consequences of loss of mission-critical assets (e.g., time and cost to recover required capability and impact on operational readiness); and (4) analysis of the effectiveness of physical protection elements. CPA -- Cost and Performance Analysis -- addresses the fourth of these four issues. CPA is a methodology that joins Activity Based Cost estimation with performance-based analysis of physical protection systems. CPA offers system managers an approach that supports both tactical decision making and strategic planning. Current exploratory applications of the CPA methodology address analysis of alternative conceptual designs. Hypothetical data is used to illustrate this process

  19. Antidotal or protective effects of Curcuma longa (turmeric) and its active ingredient, curcumin, against natural and chemical toxicities: A review.

    Science.gov (United States)

    Hosseini, Azar; Hosseinzadeh, Hossein

    2018-03-01

    Curcuma longa is a rhizomatous perennial herb that belongs to the family Zingiberaceae, native to South Asia and is commonly known as turmeric. It is used as herbal remedy due to the prevalent belief that the plant has medical properties. C. longa possesses different effects such as antioxidant, anti-tumor, antimicrobial, anti-inflammatory, wound healing, and gastroprotective activities. The recent studies have shown that C. longa and curcumin, its important active ingredient, have protective effects against toxic agents. In this review article, we collected in vitro and animal studies which are related to protective effects of turmeric and its active ingredient against natural and chemical toxic agents. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

  20. RESEARCH OF UV-PROTECTIVE ACTIVITY OF FERULIC ACID AS PART OF OINTMENT COMPOSITIONS WITH DIFFERENT PHYSICAL AND CHEMICAL PROPERTIES

    Directory of Open Access Journals (Sweden)

    I. L. Abisalova

    2014-01-01

    Full Text Available Cosmetics with the ability to neutralize harmful influence of ultraviolet rays on skin are quite in demand. UV filters in creams composition are divided into two groups: physical and chemical. Antioxidants are used as chemical UV filters. The article presents the results of ferulic acid testing as UV filter in ointment bases with lipophile, hydrophile and lipophilic and hydrophilic properties. The dependence of ferulic acid efficiency from the base type where it was applied was established. The results received are correlated with data about release rate of ferulic acid received in vitro. Ointment bases with such emulsifiers as cetyl alcohol, base emulsifier and Olivem 1000 have the most signified UV protective effect of ferulic acid.

  1. Chemical synthesis of dual labeled proteins via differently protected alkynes enables intramolecular FRET analysis.

    Science.gov (United States)

    Hayashi, Gosuke; Kamo, Naoki; Okamoto, Akimitsu

    2017-05-30

    We report a novel method for multisite protein conjugation by setting differently silyl-protected alkynes as conjugation handles, which can remain intact through the whole synthetic procedure and provide sequential and orthogonal conjugation. This strategy enables efficient preparation of a dual dye-labeled protein and structural analysis via an intramolecular FRET mechanism.

  2. Comparing Child Protective Investigation Performance between Law Enforcement Agencies and Child Welfare Agencies

    Science.gov (United States)

    Jordan, Neil; Yampolskaya, Svetlana; Gustafson, Mara; Armstrong, Mary; McNeish, Roxann; Vargo, Amy

    2011-01-01

    This study examines the comparative effectiveness of using law enforcement agencies for child protective investigation (CPI), in contrast with the traditional approach of CPI conducted by the public child welfare agency. The analysis uses 2006-2007 data from a natural experiment conducted in Florida to show modest differences in performance and…

  3. The relation between the secrecy rate of biometric template protection and biometric recognition performance

    NARCIS (Netherlands)

    Veldhuis, Raymond N.J.

    2015-01-01

    A theoretical result relating the maximum achievable security of the family of biometric template protection systems known as key-binding systems to the recognition performance of a biometric recognition system that is optimal in Neyman-Pearson sense is derived. The relation allows for the

  4. Milk Chemical Composition of Dairy Cows Fed Rations Containing Protected Omega-3 Fatty Acids and Fermented Rice Bran

    Directory of Open Access Journals (Sweden)

    Sudibya

    2013-12-01

    Full Text Available The research was conducted to investigate the effect of ration containing protected omega-3 and fermented rice bran on chemical composition of dairy milk. The research employed 10 female PFH dairy cows of 2-4 years old with body weight 300-375 kg. The research was assigned in randomized complete block design. The treatment consisted of P0= control ration, P1= P0 + 20% fermented rice bran, P2= P1 + 4% soya bean oil, P3= P1 + 4% protected tuna fish oil and P4= P1 + 4% protected lemuru fish oil. The results showed that the effects of fish oil supplementation in the rations significantly (P<0.01 decreased feed consumption, cholesterol, low density lipoprotein, lipids, and saturated fatty acids. Meanwhile, it increased milk production, content of high density lipoprotein, omega-3, omega-6 and unsaturated fatty acids in the dairy cows milk. It is concluded that the inclusion of 4% protected fish oil in the rations can produce healthy milk by decreasing milk cholesterol and increasing omega-3 fatty acids content.

  5. Semiochemical sabotage: behavioral chemicals for protection of western conifers from bark beetles

    Science.gov (United States)

    Nancy. E. Gillette; A. Steve Munson

    2009-01-01

    The discovery and elucidation of volatile behavioral chemicals used by bark beetles to locate hosts and mates has revealed a rich potential for humans to sabotage beetle host-finding and reproduction. Here, we present a description of currently available semiochemical methods for use in monitoring and controlling bark beetle pests in western conifer forests. Delivery...

  6. The Role of Riparian Vegetation in Protecting and Improving Chemical Water Quality in Streams

    Science.gov (United States)

    Michael G. Dosskey; Philippe Vidon; Noel P. Gurwick; Craig J. Allan; Tim P. Duval; Richard Lowrance

    2010-01-01

    We review the research literature and summarize the major processes by which riparian vegetation influences chemical water quality in streams, as well as how these processes vary among vegetation types, and discuss how these processes respond to removal and restoration of riparian vegetation and thereby determine the timing and level of response in stream water quality...

  7. Effect of Reused Litter and Chemical Amendment on Broiler Chicken Performance and Litter Quality

    Directory of Open Access Journals (Sweden)

    M Lotfi

    2016-06-01

    Full Text Available An experiment was conducted to evaluate the effect of chemical amendments and reused litter on broiler performances, immune response and skin quality. Five hundred and seventy six (576 day old broiler chickens were randomly allocated to 3x2 factorial design experiment. Three amendments treatment included control (no chemical addition, alunminum sulfate and zeolite; two types of litter were new and reused one. There were 4 replicates and 24 broiler chickens in each pen. The feed and water were available ad libitum during 42 days of experiment. The type of bedding had no significant effect on broilers performances (weight gain, feed efficiency ratio and mortality. Chemical amendments improved broilers performances during 0-35 days of production period but by the end of experiment there was no differences between treatment groups. Neither bedding type nor chemical amendments influenced skin erosion criteria responses. The immune response of broilers was not affected by either type of bedding or chemical amendments. It could be concluded that although beddings to be reused, it should be treated so as to overcome any defect of reused bedding.

  8. Chemical modification of conventional cancer radiotherapy. Tumor sensitization combined with normal tissue protection

    International Nuclear Information System (INIS)

    Kagiya, Tsutomu

    2006-01-01

    Nitrotriazole radiosensitizer, Sanazole (AK-2123, N-(2'-methoxyethyl)-2-(3''-nitro-1''-triazolyl) acetamide) developed by Kyoto University group was studied by 18 groups of 7 countries on fundamental aspects and clinical studies by 30 groups of 12 countries, and reported its effects on tumor sensitization of conventional cancer radiotherapy. On the other hand, the glucosides of vitamin C (Ascorbic acid glucoside, (AsAG) and water soluble derivative of vitamin-E (α-tocopherol glucoside, TMG) developed by Kyoto University group were studied fundamentally by 4 groups of 4 countries and clinically by 2 groups of 2 countries, and reported their effects on normal tissue protection in cancer treatments. These two studies of tumor sensitization and normal tissue protection were proposed as an advanced strategy of conventional cancer radiotherapy. (author)

  9. Chemical protection against long term effects in mice exposed to supralethal doses of X rays

    International Nuclear Information System (INIS)

    Maisin, J.R.

    1982-01-01

    Our results demonstrate that mixtures of radioprotectors increase the degree of protection against the short and the long term effects compared with that obtained with each substance given separately. The most potent mixtures of radioprotectors (AET, MEA, Cyst, GSH, 5-HT) yield for the long term survival a dose reduction factor of 2.1. Pulmonary lesions are most often the cause of death in protected mice irradiated with 13.5 Gy or more. At the time of death signs of sclerosis and atrophy in several tissues are associated with these lung lesions in most mice and increase with dose and time after exposure. The tissues most affected are the kidney, the alimentary tract, the liver and the lymphoid tissues [fr

  10. Animal experiment studies on biological and chemical radiation protection - the combined effects of serotonin and erythropoletin

    International Nuclear Information System (INIS)

    Sasse, U.

    1975-01-01

    The influence of a prophylactic combination treatment with serotonin and erythropoietin on the inhibited erythropoiesis of whole-body irradiated mice (500 R) was studied. Both erythropoietin and serotonin turned out to compensate the radiation-induced inhibition of the formation rate for erythrocytes to a small extent. However, only the enhancement of erythropoiesis due to serotonin indicated significant values. Yet the combined application of the named substances yielded a distinct and significant effect in radiation protection which even exceeded the simple addition of the protective effect yielded by serotonin and erythropoietin alone. But despite of this considerable success the radiation damage in the erythropoietic system was not even half compensated for. (orig./MG) [de

  11. Physical-chemical basis of the protection of slowly frozen human erythrocytes by glycerol

    Energy Technology Data Exchange (ETDEWEB)

    Rall, W.F.; Mazur, P.; Souzu, H.

    1978-07-01

    One theory of freezing damage suggests that slowly cooled cells are killed by being exposed to increasing concentrations of electrolytes as the suspending medium freezes. A corollary to this view is that protective additives such as glycerol protect cells by acting colligatively to reduce the electrolyte concentration at any subzero temperature. Recently published phase-diagram data for the ternary system glycerol-NaCl-water by M.L. Shepard et al. (Cryobiology, 13: 9-23, 1976), in combination with the data on human red cell survival vs. subzero temperature presented here and in the companion study of Souzu and Mazur (Biophys. J., 23: 89-100), permit a precise test of this theory. Appropriate liquidus phase-diagram information for the solutions used in the red cell freezing experiments was obtained by interpolation of liquidus data of Shepard and his co-workers. The results of phase-diagram analysis of red cell survival indicate that the correlation between the temperature that yields 50% hemolysis (LT/sub 50/) and the electrolyte concentration attained at that temperature in various concentrations of glycerol is poor. With increasing concentrations of glycerol, the cells were killed at progressively lower concentrations of NaCl. For example, the LT/sub 50/ for cells frozen in the absence of glycerol corresponds to a NaCl concentration of 12 weight percent (2.4 molal), while for cells frozen in 1.75 M glycerol in buffered saline the LT/sub 50/ corresponds to 3.0 weight percent NaCl (1.3 molal). The data, in combination with other findings, lead to two conclusions: (a) The protection from glycerol is due to its colligative ability to reduce the concentration of sodium chloride in the external medium, but (b) the protection is less than that expected from colligative effects; apparently glycerol itself can also be a source of damage, probably because it renders the red cells susceptible to osmotic shock during thawing.

  12. The development of chemically vapor deposited mullite coatings for the corrosion protection of SiC

    Energy Technology Data Exchange (ETDEWEB)

    Auger, M.; Hou, P.; Sengupta, A.; Basu, S.; Sarin, V. [Boston Univ., MA (United States)

    1998-05-01

    Crystalline mullite coatings have been chemically vapor deposited onto SiC substrates to enhance the corrosion and oxidation resistance of the substrate. Current research has been divided into three distinct areas: (1) Development of the deposition processing conditions for increased control over coating`s growth rate, microstructure, and morphology; (2) Analysis of the coating`s crystal structure and stability; (3) The corrosion resistance of the CVD mullite coating on SiC.

  13. Toxicity induced by chemical warfare agents: insights on the protective role of melatonin.

    Science.gov (United States)

    Pita, René; Marco-Contelles, José; Ramos, Eva; Del Pino, Javier; Romero, Alejandro

    2013-11-25

    Chemical Warfare Agents (CWAs) are substances that can be used to kill, injure or incapacitate an enemy in warfare, but also against civilian population in terrorist attacks. Many chemical agents are able to generate free radicals and derived reactants, excitotoxicity process, or inflammation, and as consequence they can cause neurological symptoms and damage in different organs. Nowadays, taking into account that total immediate decontamination after exposure is difficult to achieve and there are not completely effective antidotes and treatments against all CWAs, we advance and propose that medical countermeasures against CWAs poisoning would benefit from a broad-spectrum multipotent molecule. Melatonin, a versatile and ubiquitous antioxidant molecule, originally discovered as a hormone synthesized mainly in the pineal gland, has low toxicity and high efficacy in reducing oxidative damage, anti-inflammatory effects by regulation of multiple cellular pathways and properties to prevent excitotoxicity, among others. The purpose of this review is to show the multiple and diverse properties of melatonin, as a pleiotropic indole derivative, and its marked potential for improving human health against the most widely used chemical weapons. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  14. Effect of cold conditions on manual performance while wearing petroleum industry protective clothing.

    Science.gov (United States)

    Wiggen, Øystein Nordrum; Heen, Sigri; Færevik, Hilde; Reinertsen, Randi Eidsmo

    2011-01-01

    The purpose of this study was to investigate manual performance and thermal responses during low work intensity in persons wearing standard protective clothing in the petroleum industry when they were exposed to a range of temperatures (5, -5, -15 and -25℃) that are relevant to environmental conditions for petroleum industry personnel in northern regions. Twelve men participated in the study. Protective clothing was adjusted for the given cold exposure according to current practices. The subjects performed manual tests five times under each environmental condition. The manual performance test battery consisted of four different tests: tactile sensation (Semmes-Weinstein monofilaments), finger dexterity (Purdue Pegboard), hand dexterity (Complete Minnesota dexterity test) and grip strength (grip dynamometer). We found that exposure to -5℃ or colder lowered skin and body temperatures and reduced manual performance during low work intensity. In conclusion the current protective clothing at a given cold exposure is not adequate to maintain manual performance and thermal balance for petroleum workers in the high north.

  15. Dispelling urban myths about default uncertainty factors in chemical risk assessment--sufficient protection against mixture effects?

    Science.gov (United States)

    Martin, Olwenn V; Martin, Scholze; Kortenkamp, Andreas

    2013-07-01

    Assessing the detrimental health effects of chemicals requires the extrapolation of experimental data in animals to human populations. This is achieved by applying a default uncertainty factor of 100 to doses not found to be associated with observable effects in laboratory animals. It is commonly assumed that the toxicokinetic and toxicodynamic sub-components of this default uncertainty factor represent worst-case scenarios and that the multiplication of those components yields conservative estimates of safe levels for humans. It is sometimes claimed that this conservatism also offers adequate protection from mixture effects. By analysing the evolution of uncertainty factors from a historical perspective, we expose that the default factor and its sub-components are intended to represent adequate rather than worst-case scenarios. The intention of using assessment factors for mixture effects was abandoned thirty years ago. It is also often ignored that the conservatism (or otherwise) of uncertainty factors can only be considered in relation to a defined level of protection. A protection equivalent to an effect magnitude of 0.001-0.0001% over background incidence is generally considered acceptable. However, it is impossible to say whether this level of protection is in fact realised with the tolerable doses that are derived by employing uncertainty factors. Accordingly, it is difficult to assess whether uncertainty factors overestimate or underestimate the sensitivity differences in human populations. It is also often not appreciated that the outcome of probabilistic approaches to the multiplication of sub-factors is dependent on the choice of probability distributions. Therefore, the idea that default uncertainty factors are overly conservative worst-case scenarios which can account both for the lack of statistical power in animal experiments and protect against potential mixture effects is ill-founded. We contend that precautionary regulation should provide an

  16. Dispelling urban myths about default uncertainty factors in chemical risk assessment – sufficient protection against mixture effects?

    Science.gov (United States)

    2013-01-01

    Assessing the detrimental health effects of chemicals requires the extrapolation of experimental data in animals to human populations. This is achieved by applying a default uncertainty factor of 100 to doses not found to be associated with observable effects in laboratory animals. It is commonly assumed that the toxicokinetic and toxicodynamic sub-components of this default uncertainty factor represent worst-case scenarios and that the multiplication of those components yields conservative estimates of safe levels for humans. It is sometimes claimed that this conservatism also offers adequate protection from mixture effects. By analysing the evolution of uncertainty factors from a historical perspective, we expose that the default factor and its sub-components are intended to represent adequate rather than worst-case scenarios. The intention of using assessment factors for mixture effects was abandoned thirty years ago. It is also often ignored that the conservatism (or otherwise) of uncertainty factors can only be considered in relation to a defined level of protection. A protection equivalent to an effect magnitude of 0.001-0.0001% over background incidence is generally considered acceptable. However, it is impossible to say whether this level of protection is in fact realised with the tolerable doses that are derived by employing uncertainty factors. Accordingly, it is difficult to assess whether uncertainty factors overestimate or underestimate the sensitivity differences in human populations. It is also often not appreciated that the outcome of probabilistic approaches to the multiplication of sub-factors is dependent on the choice of probability distributions. Therefore, the idea that default uncertainty factors are overly conservative worst-case scenarios which can account both for the lack of statistical power in animal experiments and protect against potential mixture effects is ill-founded. We contend that precautionary regulation should provide an

  17. The hydrochloride of methyl(amino 2 ethylthio) 2 glycolate (C511). Its position in chemical radiation protection

    International Nuclear Information System (INIS)

    Frossard, S.C.H.

    1974-01-01

    To measure the effectiveness of a protective agent it is necessary to estimate the radiobiological damage or lack of damage if the protector is efficient. This study covers action mechanisms on the one hand and present-day possibilities of biological dosimetry on the other, concentrating essentially on chemical radioprotection in mammals. The methods normally used are described first, then the tests developed and employed to estimate the radioprotective power of C511. Systematization of the sorting of radioprotective substances is presented as the only method by which the protective capacity of a chemical substance can be evaluated strictly. An obstacle still frequently encountered in this sorting process is the fact that apart from propylene glycol and mygliol no solvent exists for the water-insoluble products. The result is a substantial wastage in the products adressed after synthesis. An effort should be made with chemists concerned to find a wider range of solvents. C511 or the hydrochloride of methyl (amino 2 ethylthio) 2 glycolate has proved an especially efficient radioprotector worth investigating further. Its atoxicity and effectiveness when administered 24 hours before irradiation give it a clear superiority over the traditional radioprotectors AET and 5HT and over more recent substances of the WR series which are not without toxicity. A product such as C511, while opening the way to new syntheses and new research on action mechanisms, may already be considered for use in human therapy [fr

  18. River-bed erosion due to changing boundary conditions: performance of a protective measure

    Directory of Open Access Journals (Sweden)

    D. Termini

    2014-09-01

    Full Text Available Due to the introduction of man-made sediment barriers along a river, the amount of sediment load entering the downstream river reach is different to that leaving the reach, and erosion processes occur downstream of the barrier itself. Designers are often required to take into account the scouring process and to include adequate protective measures against the local scour. This paper addresses the performance of bio-engineering protective measures against the erosion process. In particular, a green carpet, realized with real flexible vegetation, has been used as the protective measure against erosion processes downstream of a rigid bed. Analyses are based on experimental work carried out in a straight channel constructed at the laboratory of the Dipartimento di Ingegneria Civile, Ambientale, Aereospaziale, dei Materiali, Palermo University (Italy.

  19. Cost and performance analysis of conceptual designs of physical protection systems

    International Nuclear Information System (INIS)

    Hicks, M.J.; Snell, M.S.; Sandoval, J.S.; Potter, C.S.

    1998-01-01

    CPA -- Cost and Performance Analysis -- is a methodology that joins Activity Based Cost (ABC) estimation with performance based analysis of physical protection systems. CPA offers system managers an approach that supports both tactical decision making and strategic planning. Current exploratory applications of the CPA methodology are addressing analysis of alternative conceptual designs. To support these activities, the original architecture for CPA, is being expanded to incorporate results from a suite of performance and consequence analysis tools such as JTS (Joint Tactical Simulation), ERAD (Explosive Release Atmospheric Dispersion) and blast effect models. The process flow for applying CPA to the development and analysis conceptual designs is illustrated graphically

  20. Under pressure: evolutionary engineering of yeast strains for improved performance in fuels and chemicals production

    NARCIS (Netherlands)

    Mans, R.; Daran, J.G.; Pronk, J.T.

    2018-01-01

    Evolutionary engineering, which uses laboratory evolution to select for industrially relevant traits, is a popular strategy in the development of high-performing yeast strains for industrial production of fuels and chemicals. By integrating whole-genome sequencing, bioinformatics, classical

  1. Spunlaced and chemically bonded nonwovens for filtration applications: Performance evaluation and comparison

    CSIR Research Space (South Africa)

    Boguslavsky, L

    2008-11-01

    Full Text Available . The physical, mechanical and performance properties were measured and compared. It was concluded that chemical bonding had a higher effect on the fabric structural changes, such as pore size and its distribution. The results showed an improvement in dust...

  2. Radiation protection - Performance criteria for service laboratories performing biological dosimetry by cytogenetics

    International Nuclear Information System (INIS)

    2004-01-01

    This International Standard provides criteria for quality assurance and quality control, evaluation of the performance and the accreditation of biological dosimetry by cytogenetic service laboratories. This International Standard addresses: a) the confidentiality of personal information, for the customer and the service laboratory, b) the laboratory safety requirements, c) the calibration sources and calibration dose ranges useful for establishing the reference dose-effect curves allowing the dose estimation from chromosome aberration frequency, and the minimum detection levels, d) the scoring procedure for unstable chromosome aberrations used for biological dosimetry, e) the criteria for converting a measured aberration frequency into an estimate of absorbed dose, f) the reporting of results, g) the quality assurance and quality control, h) informative annexes containing examples of a questionnaire, instructions for customers, a data sheet for recording aberrations and a sample report

  3. UV-blocking spectacle lens protects against UV-induced decline of visual performance.

    Science.gov (United States)

    Liou, Jyh-Cheng; Teng, Mei-Ching; Tsai, Yun-Shan; Lin, En-Chieh; Chen, Bo-Yie

    2015-01-01

    Excessive exposure to sunlight may be a risk factor for ocular diseases and reduced visual performance. This study was designed to examine the ability of an ultraviolet (UV)-blocking spectacle lens to prevent visual acuity decline and ocular surface disorders in a mouse model of UVB-induced photokeratitis. Mice were divided into 4 groups (10 mice per group): (1) a blank control group (no exposure to UV radiation), (2) a UVB/no lens group (mice exposed to UVB rays, but without lens protection), (3) a UVB/UV400 group (mice exposed to UVB rays and protected using the CR-39™ spectacle lens [UV400 coating]), and (4) a UVB/photochromic group (mice exposed to UVB rays and protected using the CR-39™ spectacle lens [photochromic coating]). We investigated UVB-induced changes in visual acuity and in corneal smoothness, opacity, and lissamine green staining. We also evaluated the correlation between visual acuity decline and changes to the corneal surface parameters. Tissue sections were prepared and stained immunohistochemically to evaluate the structural integrity of the cornea and conjunctiva. In blank controls, the cornea remained undamaged, whereas in UVB-exposed mice, the corneal surface was disrupted; this disruption significantly correlated with a concomitant decline in visual acuity. Both the UVB/UV400 and UVB/photochromic groups had sharper visual acuity and a healthier corneal surface than the UVB/no lens group. Eyes in both protected groups also showed better corneal and conjunctival structural integrity than unprotected eyes. Furthermore, there were fewer apoptotic cells and less polymorphonuclear leukocyte infiltration in corneas protected by the spectacle lenses. The model established herein reliably determines the protective effect of UV-blocking ophthalmic biomaterials, because the in vivo protection against UV-induced ocular damage and visual acuity decline was easily defined.

  4. Stimulation or Inhibition: Conflicting evidence for (+/-)-catechin's role as a chemical facilitator and disease protecting agent.

    Science.gov (United States)

    Bais, Harsh P; Venkatachalam, L; Biedrzycki, Meredith L

    2010-03-01

    The occurrence of plant hormesis is a poorly understood phenomenon, wherein low doses of phytotoxins unusually promote growth responses in higher plants. In contrast, negative plant-plant interactions mediated through secreted small molecular weight compounds initiate growth inhibitory responses. Studies related to (+/-)-catechin mediated allelopathy have transpired both novel information and generated significant controversy. Specifically, studies related to the phytotoxicity responses mediated by (+/-)-catechins have been seriously debated. The pronged opinion that (+/-)-catechin is phytotoxic versus non-phytotoxic relies more on the target plant systems and the conditions used to test phytotoxic responses. It is reported that lower than MIC dosage supplementation of (+/-)-catechin could promote growth responses in the model plant Arabidopsis thaliana. Furthermore, it was shown that sub-MIC levels of (+/-)-catechin supplementation leads to elicitation of disease resistance against Pseudomonas syringae DC3000 (hereafter DC3000). Intrigued by the unique hormesis response observed, we tested whether (+/-)-catechin indeed promotes growth responses in A. thaliana. In our hands, we observed no growth promotion responses of (+/-)-catechin against A. thaliana under in vitro or in soil conditions. We also evaluated the previously reported disease protecting properties of (+/-)-catechin in A. thaliana against DC3000. The systematic observations to evaluate disease protecting properties entailing colony counts, disease incidences and loss of chlorophyll studies showed no disease protecting properties of (+/-)-catechin. The transcriptional response for a marker pathogenesis related PR1 defense gene showed no induction post (+/-)-catechin supplementation. The cell death genes (ACD2 and CAD1) associated with programmed cell death revealed unchanged expression levels in plants treated with sub-MIC levels of (+/-)-catechin. Further, we report supplementation of sub-MIC levels of

  5. Chemical radiation protection of certain aspects of carbohydrate metabolism in irradiated rats

    International Nuclear Information System (INIS)

    Abdelaziz, M.T.; Roushdy, H.M.; Saleh, S.; El-denshary, E.S.M.; Maklad, T.A.

    1985-01-01

    Because of the practical importance of certain compounds that exhibit protective character against lethal effects of ionizing radiation, repeated investigations have been carried out to evaluate the radioprotective efficiency of such compounds and to study the mechanism through which they manifest their radioprotective effects. The present study is an attempt to investigate the possible role which the heterocyclic nitrogenous compounds (glyoxaline and benzoglyoxaline) can play as radioprotectors against radiation-induced changes in carbohydrate metabolism. The parameters studied were, survival rate, bloodglucose level, gamma insulin level and liver glycogen concentration

  6. Chemical radiation protection of certain aspects of carbohydrate metabolism in irradiated rats

    Energy Technology Data Exchange (ETDEWEB)

    Abdelaziz, M T; Roushdy, H M; Saleh, S; El-denshary, E S.M.; Maklad, T A [National Centre for Radiation Research and Technology, Cairo (Egypt)

    1985-01-01

    Because of the practical importance of certain compounds that exhibit protective character against lethal effects of ionizing radiation, repeated investigations have been carried out to evaluate the radioprotective efficiency of such compounds and to study the mechanism through which they manifest their radioprotective effects. The present study is an attempt to investigate the possible role which the heterocyclic nitrogenous compounds (glyoxaline and benzoglyoxaline) can play as radioprotectors against radiation-induced changes in carbohydrate metabolism. The parameters studied were, survival rate, bloodglucose level, gamma insulin level and liver glycogen concentration.

  7. Joint Project Manager (JPM) Chemical Biological Individual and Collective Protection Industry Day

    Science.gov (United States)

    2008-07-22

    ANSWER: The SBA operates the Office of Women’s B i O hi Th OWBO t thus ness wners p. e promo es e growth of women owned businesses through programs...TIC prioritization focused on a h i i k t f h tcompre ens ve r s managemen o w a we do not know: Absolute global production levels Absolute global...Modeling (For operational analyses) 2. Breakthrough Levels 3 D t ti A h. e ec on pproac es Multiple species may be present 4. Chemical Class Analysis

  8. Performance comparison of LOE protection of synchronous generator in the presence of UPFC

    Directory of Open Access Journals (Sweden)

    Seyed Yaser Ebrahimi

    2016-03-01

    Full Text Available Generator loss of excitation (LOE protection is a principal protection of power system which operate based on impedance measurement. This relay calculates impedance by measuring voltage and current at the generator terminal. On the other hand, the presence of unified power flow controller (UPFC in transmission lines changes measured voltage and current signals during loss of excitation. In this paper, the impact of UPFC on the performance of LOE protection has been analytically investigated. Afterwards, using modeling results, it has been attained that the presence of UPFC leads to the drastic delay on the performance of LOE relay. This delay results to the overloading and damaging of armature winding of generator. It is also shown that in partial LOE presence of UPFC causes under-reach of the relay. Finally, the phasor measurement units (PMUs based method has been proposed to reduce the effect of UPFC on the LOE protection. The results indicate that using this new method, the delay of LOE relay has been reduced. In the surveys conducted, various conditions of the power system have been considered.

  9. Modified clay minerals efficiency against chemical and biological warfare agents for civil human protection.

    Science.gov (United States)

    Plachá, Daniela; Rosenbergová, Kateřina; Slabotínský, Jiří; Kutláková, Kateřina Mamulová; Studentová, Soňa; Martynková, Gražyna Simha

    2014-04-30

    Sorption efficiencies of modified montmorillonite and vermiculite of their mono ionic Na and organic HDTMA and HDP forms were studied against chemical and biological warfare agents such as yperite and selected bacterial strains. Yperite interactions with modified clay minerals were observed through its capture in low-density polyethylene foil-modified clay composites by measuring yperite gas permeation with using chemical indication and gas chromatography methods. The antibacterial activities of synthetized organoclays were tested against selected Gram-positive and Gram-negative bacterial species in minimum inhibitory concentration tests. The obtained results showed a positive influence of modified clay minerals on the significant yperite breakthrough-time increase. The most effective material was the polyethylene-Na form montmorillonite, while the polyethylene-Na form vermiculite showed the lowest efficiency. With increasing organic cations loading in the interlayer space the montmorillonite efficiency decreased, and in the case of vermiculite an opposite effect was observed. Generally the modified montmorillonites were more effective than modified vermiculites. The HDP cations seem to be more effective compare to the HDTMA. The antibacterial activity tests confirmed efficiency of all organically modified clay minerals against Gram-positive bacteria. The confirmation of antibacterial activity against Y. pestis, plague bacteria, is the most interesting result of this part of the study. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. Integration of nanostructured materials with MEMS microhotplate platforms to enhance chemical sensor performance

    International Nuclear Information System (INIS)

    Benkstein, Kurt D.; Martinez, Carlos J.; Li, Guofeng; Meier, Douglas C.; Montgomery, Christopher B.; Semancik, Steve

    2006-01-01

    The development of miniaturized chemical sensors is an increasingly active area of research. Such devices, particularly when they feature low mass and low power budgets, can impact a broad range of applications including industrial process monitoring, building security and extraterrestrial exploration. Nanostructured materials, because of their high surface area, can provide critical enhancements in the performance of chemical microsensors. We have worked to integrate nanomaterial films with MEMS (microelectromechanical systems) microhotplate platforms developed at the National Institute of Standards and Technology in order to gain the benefits of both the materials and the platforms in high-performance chemical sensor arrays. Here, we describe our success in overcoming the challenges of integration and the benefits that we have achieved with regard to the critical sensor performance characteristics of sensor response, speed, stability and selectivity. Nanostructured metal oxide sensing films were locally deposited onto microhotplates via chemical vapor deposition and microcapillary pipetting, and conductive polymer nanoparticle films were deposited via electrophoretic patterning. All films were characterized by scanning electron microscopy and evaluated as conductometric gas sensors

  11. Protective

    Directory of Open Access Journals (Sweden)

    Wessam M. Abdel-Wahab

    2013-10-01

    Full Text Available Many active ingredients extracted from herbal and medicinal plants are extensively studied for their beneficial effects. Antioxidant activity and free radical scavenging properties of thymoquinone (TQ have been reported. The present study evaluated the possible protective effects of TQ against the toxicity and oxidative stress of sodium fluoride (NaF in the liver of rats. Rats were divided into four groups, the first group served as the control group and was administered distilled water whereas the NaF group received NaF orally at a dose of 10 mg/kg for 4 weeks, TQ group was administered TQ orally at a dose of 10 mg/kg for 5 weeks, and the NaF-TQ group was first given TQ for 1 week and was secondly administered 10 mg/kg/day NaF in association with 10 mg/kg TQ for 4 weeks. Rats intoxicated with NaF showed a significant increase in lipid peroxidation whereas the level of reduced glutathione (GSH and the activity of superoxide dismutase (SOD, catalase (CAT, glutathione S-transferase (GST and glutathione peroxidase (GPx were reduced in hepatic tissues. The proper functioning of the liver was also disrupted as indicated by alterations in the measured liver function indices and biochemical parameters. TQ supplementation counteracted the NaF-induced hepatotoxicity probably due to its strong antioxidant activity. In conclusion, the results obtained clearly indicated the role of oxidative stress in the induction of NaF toxicity and suggested hepatoprotective effects of TQ against the toxicity of fluoride compounds.

  12. Increasing Optimism Protects Against Pain-Induced Impairment in Task-Shifting Performance.

    Science.gov (United States)

    Boselie, Jantine J L M; Vancleef, Linda M G; Peters, Madelon L

    2017-04-01

    Persistent pain can lead to difficulties in executive task performance. Three core executive functions that are often postulated are inhibition, updating, and shifting. Optimism, the tendency to expect that good things happen in the future, has been shown to protect against pain-induced performance deterioration in executive function updating. This study tested whether this protective effect of a temporary optimistic state by means of a writing and visualization exercise extended to executive function shifting. A 2 (optimism: optimism vs no optimism) × 2 (pain: pain vs no pain) mixed factorial design was conducted. Participants (N = 61) completed a shifting task once with and once without concurrent painful heat stimulation after an optimism or neutral manipulation. Results showed that shifting performance was impaired when experimental heat pain was applied during task execution, and that optimism counteracted pain-induced deterioration in task-shifting performance. Experimentally-induced heat pain impairs shifting task performance and manipulated optimism or induced optimism counteracted this pain-induced performance deterioration. Identifying psychological factors that may diminish the negative effect of persistent pain on the ability to function in daily life is imperative. Copyright © 2016 American Pain Society. Published by Elsevier Inc. All rights reserved.

  13. Comparing child protective investigation performance between law enforcement agencies and child welfare agencies.

    Science.gov (United States)

    Jordan, Neil; Yampolskaya, Svetlana; Gustafson, Mara; Armstrong, Mary; McNeish, Roxann; Vargo, Amy

    2011-01-01

    This study examines the comparative effectiveness of using law enforcement agencies for child protective investigation (CPI), in contrast with the traditional approach of CPI conducted by the public child welfare agency. The analysis uses 2006-2007 data from a natural experiment conducted in Florida to show modest differences in performance and cost-efficiency between the two approaches to CPI. These findings may have implications for other states considering outsourcing CPI to law enforcement.

  14. Regularities of development of unspecific reaction of cells, and modification of chemical protection

    International Nuclear Information System (INIS)

    Veksler, A.M.; Korystov, Yu.N.; Kublik, L.N.; Ehjdus, L.Kh.

    1979-01-01

    Regularities of development of a unspecific reaction of cells under the effect of different substances belonging to weak electrolytes have been studied. It was demonstrated that the rate of the unspecific reaction development under the effect of cysteamine and caffeine-benzoate depends on the agent concentration, temperature and pH of a medium. It was established that the response of a cell is determined by the overall intracellular concentration of the agent rather than by its specific character. The total concentration of the substance inside the cell depends on its physico-chemical characteristics and, with a pH gradient between cell and medium, can markedly vary from that in the medium. With similar intracellular content, both substances proved to be virtually equally effective. This suggests that it is possible to assess the effectiveness of some other biologically active substances many of which are weak electrolytes

  15. Cocktail of chemical compounds robustly promoting cell reprogramming protects liver against acute injury

    Directory of Open Access Journals (Sweden)

    Yuewen Tang

    2017-02-01

    Full Text Available Abstract Tissue damage induces cells into reprogramming-like cellular state, which contributes to tissue regeneration. However, whether factors promoting the cell reprogramming favor tissue regeneration remains elusive. Here we identified combination of small chemical compounds including drug cocktails robustly promoting in vitro cell reprogramming. We then administrated the drug cocktails to mice with acute liver injuries induced by partial hepatectomy or toxic treatment. Our results demonstrated that the drug cocktails which promoted cell reprogramming in vitro improved liver regeneration and hepatic function in vivo after acute injuries. The underlying mechanism could be that expression of pluripotent genes activated after injury is further upregulated by drug cocktails. Thus our study offers proof-of-concept evidence that cocktail of clinical compounds improving cell reprogramming favors tissue recovery after acute damages, which is an attractive strategy for regenerative purpose.

  16. Studies of the Use of Electrochemical Impedance Spectroscopy to Characterize and Assess the Performance of Lacquers Used to Protect Aluminum Sheet and Can Ends

    Science.gov (United States)

    Ali, Mohammad

    This study involved investigating the feasibility of using Electrochemical Impedance Spectroscopy to assess the performance of coatings used to protect aluminum in beverage containers, and developing an accelerated testing procedure. In the preliminary investigation, tests were performed to ensure that the EIS systems at hand are capable, functional and consistent. This was followed by EIS testing of kitchen-aluminum foil and high-impedance epoxy polymer as a baseline for chemically-active and chemically-inert systems. The ability of EIS to differentiate between intact and flawed coatings was tested by investigating deliberately damaged coatings. The effects of varying the pH and oxygen content on the performance of the coated aluminum samples were also tested. From this investigation, it has been concluded that EIS can be used to differentiate between intact and flawed coatings and detect corrosion before it is visually observable. Signatures of corrosion have been recorded and a preliminary testing procedure has been drawn.

  17. PROCESSES PROCEEDING ON CONCRETE COATING SURFACES IN CASE OF THEIR CHEMICAL PROTECTION AGAINST WINTER SLIPPERINESS

    Directory of Open Access Journals (Sweden)

    M. K. Pshembaev

    2016-01-01

    Full Text Available Concrete coatings of road traffic highways along with operational loadings caused by flow of traffic are subjected to weather and climate impacts. These are the following impacts: changes in temperature and air humidity, solar radiation,surface wind speed which is participating in formation of active heat-and-mass transfer in a surface layer of the concrete coating. One of the most complicated and important periods in the road traffic highway operation is so called transitional nature period (from Summer to Autumn and from Winter to Spring. These periods are accompanied by intensive rain and snow fall and possible formation of ice loading on the surface of cement and concrete coatings. These impacts significantly deteriorate friction properties of road pavement (friction factor φ is decreased up to 0.4 and less that can be a prerequisite to creation of various accident situations due to sharp increase in braking distance. For example, while having dry pavement the friction factor φ is equal to 0.80–0.85, and during icy condition of the road the factor φ constitutes 0.08–0.15 that consequently entails an increase in braking distance from 7.5 up to 20.0 m and more. It is quite possible that ice layer appears on the surface of concrete coatings when road traffic highways are used in winter season. Various methods are applicable to remove ice from the surface they can include also ice-melting chemicals and sodium chloride NaCl in particular. The chemical decreases freezing temperature of the formed brine and causes ice melting at negative temperature. Processes of NaCl dissolution and ice melting have an endothermic character, in other words these processes are accompanied by heat ingress and due to it temperature is sharply decreasing in the surface layer of the concrete coating which is under the melting ice and in this case phenomenon of thermal shock is observed.

  18. Optimal loading and protection of multi-state systems considering performance sharing mechanism

    International Nuclear Information System (INIS)

    Xiao, Hui; Shi, Daimin; Ding, Yi; Peng, Rui

    2016-01-01

    Engineering systems are designed to carry the load. The performance of the system largely depends on how much load it carries. On the other hand, the failure rate of the system is strongly affected by its load. Besides internal failures, such as fatigue and aging process, systems may also fail due to external impacts such as nature disasters and terrorism. In this paper, we integrate the effect of loading and protection of external impacts on multi-state systems with performance sharing mechanism. The objective of this research is to determine how to balance the load and protection on system elements. An availability evaluation algorithm of the proposed system is suggested and the corresponding optimization problem is solved utilizing genetic algorithms. - Highlights: • Performance sharing of multi-state systems is considered. • The effect of load on system elements is analyzed. • Joint optimization model of element loading and protection is formulated. • Genetic Algorithms are adapted to solve the reliability optimization problem.

  19. Heme oxygenase-1 protects endothelial cells from the toxicity of air pollutant chemicals

    International Nuclear Information System (INIS)

    Lawal, Akeem O.; Zhang, Min; Dittmar, Michael; Lulla, Aaron; Araujo, Jesus A.

    2015-01-01

    Diesel exhaust particles (DEPs) are a major component of diesel emissions, responsible for a large portion of their toxicity. In this study, we examined the toxic effects of DEPs on endothelial cells and the role of DEP-induced heme oxygenase-1 (HO-1) expression. Human microvascular endothelial cells (HMECs) were treated with an organic extract of DEPs from an automobile engine (A-DEP) or a forklift engine (F-DEP) for 1 and 4 h. ROS generation, cell viability, lactate dehydrogenase leakage, expression of HO-1, inflammatory genes, cell adhesion molecules and unfolded protein respone (UPR) gene were assessed. HO-1 expression and/or activity were inhibited by siRNA or tin protoporphyrin (Sn PPIX) and enhanced by an expression plasmid or cobalt protoporphyrin (CoPPIX). Exposure to 25 μg/ml of A-DEP and F-DEP significantly induced ROS production, cellular toxicity and greater levels of inflammatory and cellular adhesion molecules but to a different degree. Inhibition of HO-1 enzymatic activity with SnPPIX and silencing of the HO-1 gene by siRNA enhanced DEP-induced ROS production, further decreased cell viability and increased expression of inflammatory and cell adhesion molecules. On the other hand, overexpression of the HO-1 gene by a pcDNA 3.1D/V5-HO-1 plasmid significantly mitigated ROS production, increased cell survival and decreased the expression of inflammatory genes. HO-1 expression protected HMECs from DEP-induced prooxidative and proinflammatory effects. Modulation of HO-1 expression could potentially serve as a therapeutic target in an attempt to inhibit the cardiovascular effects of ambient PM. - Highlights: • We examined the role of HO-1 expression on diesel exhaust particle (DEP) in endothelial cells. • DEPs exert cytotoxic and inflammatory effects on human microvascular endothelial cells (HMECs). • DEPs induce HO-1 expression in HMECs. • HO-1 protects against the oxidative stress induced by DEps. • HO-1 attenuates the proinflammatory effects

  20. Heme oxygenase-1 protects endothelial cells from the toxicity of air pollutant chemicals

    Energy Technology Data Exchange (ETDEWEB)

    Lawal, Akeem O.; Zhang, Min; Dittmar, Michael [Division of Cardiology, David Geffen School of Medicine, University of California, Los Angeles, 10833 Le Conte Avenue, CHS 43-264, Los Angeles, CA 90095 (United States); Lulla, Aaron [Division of Cardiology, David Geffen School of Medicine, University of California, Los Angeles, 10833 Le Conte Avenue, CHS 43-264, Los Angeles, CA 90095 (United States); Molecular Toxicology Interdepartmental Program, University of California, Los Angeles (United States); Araujo, Jesus A., E-mail: JAraujo@mednet.ucla.edu [Division of Cardiology, David Geffen School of Medicine, University of California, Los Angeles, 10833 Le Conte Avenue, CHS 43-264, Los Angeles, CA 90095 (United States); Molecular Toxicology Interdepartmental Program, University of California, Los Angeles (United States); Molecular Biology Institute, University of California, Los Angeles (United States)

    2015-05-01

    Diesel exhaust particles (DEPs) are a major component of diesel emissions, responsible for a large portion of their toxicity. In this study, we examined the toxic effects of DEPs on endothelial cells and the role of DEP-induced heme oxygenase-1 (HO-1) expression. Human microvascular endothelial cells (HMECs) were treated with an organic extract of DEPs from an automobile engine (A-DEP) or a forklift engine (F-DEP) for 1 and 4 h. ROS generation, cell viability, lactate dehydrogenase leakage, expression of HO-1, inflammatory genes, cell adhesion molecules and unfolded protein respone (UPR) gene were assessed. HO-1 expression and/or activity were inhibited by siRNA or tin protoporphyrin (Sn PPIX) and enhanced by an expression plasmid or cobalt protoporphyrin (CoPPIX). Exposure to 25 μg/ml of A-DEP and F-DEP significantly induced ROS production, cellular toxicity and greater levels of inflammatory and cellular adhesion molecules but to a different degree. Inhibition of HO-1 enzymatic activity with SnPPIX and silencing of the HO-1 gene by siRNA enhanced DEP-induced ROS production, further decreased cell viability and increased expression of inflammatory and cell adhesion molecules. On the other hand, overexpression of the HO-1 gene by a pcDNA 3.1D/V5-HO-1 plasmid significantly mitigated ROS production, increased cell survival and decreased the expression of inflammatory genes. HO-1 expression protected HMECs from DEP-induced prooxidative and proinflammatory effects. Modulation of HO-1 expression could potentially serve as a therapeutic target in an attempt to inhibit the cardiovascular effects of ambient PM. - Highlights: • We examined the role of HO-1 expression on diesel exhaust particle (DEP) in endothelial cells. • DEPs exert cytotoxic and inflammatory effects on human microvascular endothelial cells (HMECs). • DEPs induce HO-1 expression in HMECs. • HO-1 protects against the oxidative stress induced by DEps. • HO-1 attenuates the proinflammatory effects

  1. Comparison of performance of three different types of respiratory protection devices.

    Science.gov (United States)

    Lawrence, Robert B; Duling, Matthew G; Calvert, Catherine A; Coffey, Christopher C

    2006-09-01

    Respiratory protection is offered to American workers in a variety of ways to guard against potential inhalation hazards. Two of the most common ways are elastomeric N95 respirators and N95 filtering-facepiece respirators. Some in the health care industry feel that surgical masks provide an acceptable level of protection in certain situations against particular hazards. This study compared the performance of these types of respiratory protection during a simulated workplace test that measured both filter penetration and face-seal leakage. A panel of 25 test subjects with varying face sizes tested 15 models of elastomeric N95 respirators, 15 models of N95 filtering-facepiece respirators, and 6 models of surgical masks. Simulated workplace testing was conducted using a TSI PORTACOUNT Plus model 8020, and consisted of a series of seven exercises. Six simulated workplace tests were performed with redonning of the respirator/mask occurring between each test. The results of these tests produced a simulated workplace protection factor (SWPF). The geometric mean (GM) and the 5th percentile values of the SWPFs were computed by category of respiratory protection using the six overall SWPF values. The level of protection provided by each of the three respiratory protection types was compared. The GM and 5th percentile SWPF values without fit testing were used for the comparison, as surgical masks were not intended to be fit tested. The GM values were 36 for elastomeric N95 respirators, 21 for N95 filtering-facepiece respirators, and 3 for surgical masks. An analysis of variance demonstrated a statistically significant difference between all three. Elastomeric N95 respirators had the highest 5th percentile SWPF of 7. N95 filtering-facepiece respirators and surgical masks had 5th percentile SWPFs of 3 and 1, respectively. A Fisher Exact Test revealed that the 5th percentile SWPFs for all three types of respiratory protection were statistically different. In addition, both

  2. Performance enhanced headgear: a scientific approach to the development of protective headgear.

    Science.gov (United States)

    McIntosh, A; McCrory, P; Finch, C F

    2004-02-01

    There is a continuing debate about the performance of protective headgear in rugby union, rugby league, and Australian rules football. To examine the impact energy attenuation performance of foam that could be incorporated into headgear and examine the performance of prototypes of modified headgear. Impact tests were conducted on polyethylene foams and protective headgear. Free fall drop tests with a rigid headform on to a flat rigid anvil were conducted. Resultant headform acceleration was measured. Means of the headform acceleration maxima for repeat tests were calculated. Tests on polyethylene foam indicated that an increase in thickness from 10 mm to 16 mm would improve headgear performance. These modifications were incorporated in part into two headgear models: the Albion Headpro and the Canterbury brand Body Armour honeycomb headgear. The headgear tests show that significant reductions in headform acceleration were achieved by increasing the foam density and thickness. Mean headform acceleration maxima for the 16 mm thick modified rugby headgear was about 25% of that of standard headgear for lateral impact 0.3 and 0.4 m drop heights and 27% for the centre front 0.3 m drop tests. At these impacts, the headform acceleration for the modified rugby headgear was below 200 g. Significant improvements in impact energy attenuation performance are possible with small design changes. Whether these are sufficient to reduce the rate or severity of concussion in rugby and Australian rules football can only be shown by formal prospective studies on the field.

  3. Correlations between hematological, parasitological patterns and animal performance of sheep supplemented with protected fat

    Directory of Open Access Journals (Sweden)

    Vivian Alves Costa Afonso

    2010-02-01

    Full Text Available The development of populations of gastrointestinal parasites resistant to antihelmintics has led to seeks new alternatives its control. Stimulation of natural immunity by means of animal nutrition has shown promising results in controlling nematodes in sheep. The addition of protected fat sources, containing essential fatty acids, may be an alternative due to many effects, among them, regulation of immunity expression and regulation of the inflammatory response by immune effectors. The aim of this study was to estimate correlations between haematological and parasitological patterns, animal performance through weight and body condition, under the influence of protected fat in ewes. Fifty Santa Ines sheep, in the final third of pregnancy or postpartum, in paddocks of Panicum maximum, received, individually, 200 g per day of concentrate, isonitrogenous and isocaloric diets, with or without the addition of protected fat. In general, except for total leukocytes and eosinophils, almost all of Pearson correlation coefficients of other variables were significant. However, the protected fat, in the amount offered, had no antihelmintic effect.

  4. Apelin Protects Primary Rat Retinal Pericytes from Chemical Hypoxia-Induced Apoptosis

    Directory of Open Access Journals (Sweden)

    Li Chen

    2015-01-01

    Full Text Available Pericytes are a population of cells that participate in normal vessel architecture and regulate permeability. Apelin, as the endogenous ligand of G protein-coupled receptor APJ, participates in a number of physiological and pathological processes. To date, the effect of apelin on pericyte is not clear. Our study aimed to investigate the potential protection mechanisms of apelin, with regard to primary rat retinal pericytes under hypoxia. Immunofluorescence staining revealed that pericytes colocalized with APJ in the fibrovascular membranes dissected from proliferative diabetic retinopathy patients. In the in vitro studies, we first demonstrated that the expression of apelin/APJ was upregulated in pericytes under hypoxia, and apelin increased pericytes proliferation and migration. Moreover, knockdown of apelin in pericyte was achieved via lentivirus-mediated RNA interference. After the inhibition of apelin, pericytes proliferation was inhibited significantly in hypoxia culture condition. Furthermore, exogenous recombinant apelin effectively prevented hypoxia-induced apoptosis through downregulating active-caspase 3 expression and increasing the ratio of B cell lymphoma-2 (Bcl-2/Bcl-2 associated X protein (Bax in pericytes. These results suggest that apelin suppressed hypoxia-induced pericytes injury, which indicated that apelin could be a potential therapeutic target for retinal angiogenic diseases.

  5. Corrosion Protection Of Mild Steel In Sea Water Using Chemical Inhibitor

    Science.gov (United States)

    Araoyinbo, Alaba O.; Salleh, Mohd Arif Anuar Mohd; Zulerwan Jusof, Muhammad

    2018-03-01

    The effect of sodium nitrite as a corrosion inhibitor of mild steel in sea water (i.e ASTM standard prepared sea water and sea water obtained from a local river) was investigated, using the weight loss technique. Different amount of sodium nitrite were prepared (i.e 2 % to 10 %) in the inhibition of the mild steel corrosion in sea water exposed to irradiation condition from sunlight exposure. The cut samples of mild steel were exposed to these corrosive media and the corresponding weight loss subsequently obtained was recorded at intervals of 1 to 4 weeks. It was observed that corrosion rate increases with the time of exposure to the corrosive medium exposed to sunlight and that sodium nitrite that was used at the chemical inhibitor was able to retard the corrosion rate of mild steel if the appropriate concentration is applied. The results obtained from the weight loss analysis shows that the optimum percentage of sodium nitrate in sea water that gives the optimum corrosion inhibition of mild steel is 4 %.

  6. Protecting buildings from a biological or chemical attack: Actions to take before or during a release

    Energy Technology Data Exchange (ETDEWEB)

    Price, Phillip N.; Sohn, Michael D.; Gadgil, Ashok J.; Delp, William W.; Lorenzetti, David M.; Finlayson, Elizabeth U.; Thatcher, Tracy L.; Sextro, Richard G.; Derby, Elisabeth A.; Jarvis, Sondra A.

    2003-01-29

    This report presents advice on how to operate a building to reduce casualties from a biological or chemical attack, as well as potential changes to the building (e.g. the design of the ventilation system) that could make it more secure. It also documents the assumptions and reasoning behind the advice. The particular circumstances of any attack, such as the ventilation system design, building occupancy, agent type, source strength and location, and so on, may differ from the assumptions made here, in which case actions other than our recommendations may be required; we hope that by understanding the rationale behind the advice, building operators can modify it as required for their circumstances. The advice was prepared by members of the Airflow and Pollutant Transport Group, which is part of the Indoor Environment Department at the Lawrence Berkeley National Laboratory. The group's expertise in this area includes: tracer-gas measurements of airflows in buildings (Sextro, Thatcher); design and operation of commercial building ventilation systems (Delp); modeling and analysis of airflow and tracer gas transport in large indoor spaces (Finlayson, Gadgil, Price); modeling of gas releases in multi-zone buildings (Sohn, Lorenzetti, Finlayson, Sextro); and occupational health and safety experience related to building design and operation (Sextro, Delp). This report is concerned only with building design and operation; it is not a how-to manual for emergency response. Many important emergency response topics are not covered here, including crowd control, medical treatment, evidence gathering, decontamination methods, and rescue gear.

  7. Development of a methodology for the evaluation of radiation protection performance and management in nuclear power plants

    International Nuclear Information System (INIS)

    Schieber, Caroline; Bataille, Celine; Cordier, Gerard; Delabre, Herve; Jeannin, Bernard

    2008-01-01

    This paper describes a specific methodology adopted by Electricite de France to perform the evaluation of radiation protection performance and management within its 19 nuclear power plants. The results obtained in 2007 are summed up. (author)

  8. Reproductive performance of Santa Inês ewes fed protected fat diet

    Directory of Open Access Journals (Sweden)

    Ricardo Lopes Dias da Costa

    2011-06-01

    Full Text Available The objective of this work was to evaluate the reproductive performance of Santa Inês ewes fed a diet supplemented with protected fat. Intervals from lambing to first clinical estrus and to conception, conception rate, prolificacy, live weight and body condition were determined. After lambing, 60 ewes and their offsprings were weighted and randomly assigned to three treatments, based on age, body weight and number of born lambs. Treatments consisted of: control diet, or control diet plus 30 g of protected fat, from lambing to day 25 of post-lambing (Sup25, or to day 60 of post-lambing (Sup60. Out of 60 evaluated ewes, 93.3% returned to estrus, and 74.5% got pregnant, with 73.53% lambing rate and 196.5 days lambing interval. The average periods from lambing to first estrus were 32.4, 27.2 and 35.5 days for ewes fed the control diet, Sup25, and Sup60, respectively. The intervals from lambing to conception were 45.2, 46.5 and 45.2 days, and the supplemented diets did not show differences in comparison to the control diet. Supplementation with protected fat to well-nourished Santa Inês ewes does not improve their reproductive performance.

  9. Experimental investigation of material chemical effects on emergency core cooling pump suction filter performance after loss of coolant accident

    International Nuclear Information System (INIS)

    Park, Jong Woon; Park, Byung Gi; Kim, Chang Hyun

    2009-01-01

    Integral tests of head loss through an emergency core cooling filter screen are conducted, simulating reactor building environmental conditions for 30 days after a loss of coolant accident. A test rig with five individual loops each of whose chamber is established to test chemical product formation and measure the head loss through a sample filter. The screen area at each chamber and the amounts of reactor building materials are scaled down according to specific plant condition. A series of tests have been performed to investigate the effects of calcium-silicate, reactor building spray, existence of calcium-silicate with tri-sodium phosphate (TSP), and composition of materials. The results showed that head loss across the chemical bed with even a small amount of calcium-silicate insulation instantaneously increased as soon as TSP was added to the test solution. Also, the head loss across the filter screen is strongly affected by spray duration and the head loss increase is rapid at the early stage, because of high dissolution and precipitation of aluminum and zinc. After passivation of aluminum and zinc by corrosion, the head loss increase is much slowed down and is mainly induced by materials such as calcium, silicon, and magnesium leached from NUKON TM and concrete. Furthermore, it is newly found that the spay buffer agent, tri-sodium phosphate, to form protective coating on the aluminum surface and reduce aluminum leaching is not effective for a large amount of aluminum and a long spray.

  10. High-performance macroporous bulk silicon anodes synthesized by template-free chemical etching

    Energy Technology Data Exchange (ETDEWEB)

    Bang, Byoung Man; Lee, Jung-In; Kim, Hyunjung; Cho, Jaephil; Park, Soojin [Interdisciplinary School of Green Energy, Ulsan National Institute of Science and Technology (UNIST), Ulsan (Korea, Republic of)

    2012-07-15

    Three-dimensional porous silicon particles can be produced via the combination of a galvanic displacement reaction and a metal-assisted chemical etching process. This simple synthetic route can be applied to make high-performance anode materials, including high specific capacity, stable cycling retention, and high rate capability, in lithium-ion batteries. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  11. Catalytic performances of chemically immobilized urease under static and dynamic conditions: A comparative study

    OpenAIRE

    Yürekli, Yılmaz; Alsoy Altınkaya, Sacide

    2011-01-01

    Immobilized urease has been used for direct removal of urea from aqueous solution and as biological sensing material in the preparation of urea biosensors. The former application is carried out under dynamic condition using ultrafiltration membrane either in tubular form or in flat sheet, while the latter is used in static condition. In this study, the performance of chemically immobilized urease on poly(acrylonitrile-co-sodium methallyl sulfonate) ultrafiltration membrane was determined unde...

  12. Chemical Composition, Antioxidant, DNA Damage Protective, Cytotoxic and Antibacterial Activities of Cyperus rotundus Rhizomes Essential Oil against Foodborne Pathogens

    Science.gov (United States)

    Hu, Qing-Ping; Cao, Xin-Ming; Hao, Dong-Lin; Zhang, Liang-Liang

    2017-01-01

    Cyperus rotundus L. (Cyperaceae) is a medicinal herb traditionally used to treat various clinical conditions at home. In this study, chemical composition of Cyperus rotundus rhizomes essential oil, and in vitro antioxidant, DNA damage protective and cytotoxic activities as well as antibacterial activity against foodborne pathogens were investigated. Results showed that α-cyperone (38.46%), cyperene (12.84%) and α-selinene (11.66%) were the major components of the essential oil. The essential oil had an excellent antioxidant activity, the protective effect against DNA damage, and cytotoxic effects on the human neuroblastoma SH-SY5Y cell, as well as antibacterial activity against several foodborne pathogens. These biological activities were dose-dependent, increasing with higher dosage in a certain concentration range. The antibacterial effects of essential oil were greater against Gram-positive bacteria as compared to Gram-negative bacteria, and the antibacterial effects were significantly influenced by incubation time and concentration. These results may provide biological evidence for the practical application of the C. rotundus rhizomes essential oil in food and pharmaceutical industries. PMID:28338066

  13. US/Russian cooperative efforts in nuclear material protection, control, and accounting at the Siberian Chemical Combine

    International Nuclear Information System (INIS)

    Goloskokov, I.; Yarygin, A.; Petrushev, V.; Morgado, R.E.

    1998-01-01

    The Siberian Chemical Combine (SKhK) is the largest multifunction nuclear production facility in the Russian nuclear complex. Until recently, it produced and processed special nuclear material for the Russian Defense Ministry. SKhK and its US partners in the Department of Energy (DOE) US/Russian Materials Protection, Control, and Accountability (MPC and A) Program are nearing completion of the initial MPC and A upgrades at the six SKhK plant sites that were begun three years ago. Comprehensive enhancements to the physical protection and access control systems are progressing on a site-wide basis while a comprehensive MC and A system is being implemented at the Radiochemical Plant site. SKhK now produces thermal and electrical power, enriches uranium for commercial reactor fuel, reprocesses irradiated fuel, converts high-enriched uranium metal into high-enriched oxide for blending into reactor-grade, low-enriched uranium, and manufactures civilian products. The authors review the progress to date and outline plans for continuing the work in 1999

  14. Protective Performance of Polyaniline-Sulfosalicylic Acid/Epoxy Coating for 5083 Aluminum

    Science.gov (United States)

    Liu, Suyun; Liu, Li; Meng, Fandi; Li, Ying; Wang, Fuhui

    2018-01-01

    Epoxy coatings incorporating different content of sulfosalicylic acid doped polyaniline (PANI-SSA) have been investigated for corrosion protection of 5083 aluminum alloy in 3.5% NaCl solution. The performance of the coatings is studied using a combination of electrochemical impedance spectroscopy (EIS), open circuit potential (OCP), gravimetric tests, adhesion tests, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The results demonstrate that the content of PANI-SSA not only affects the coating compactness and the transportation of aggressive medium, but also has a significant influence on the-based aluminum. The coating with 2 wt. % PANI-SSA exhibits the best corrosion inhibition due to its good protective properties and the formation of a complete PANI-SSA induced oxide layer. PMID:29438304

  15. A new approach to characterize the effect of fabric deformation on thermal protective performance

    International Nuclear Information System (INIS)

    Li, Jun; Li, Xiaohui; Lu, Yehu; Wang, Yunyi

    2012-01-01

    It is very important to evaluate thermal protective performance (TPP) in laboratory-simulated fire scenes as accurately as possible. For this paper, to thoroughly understand the effect of fabric deformation on basic physical properties and TPP of flame-retardant fabrics exposed to flash fire, a new modified TPP testing apparatus was developed. Different extensions were employed to simulate the various extensions displayed during different body motions. The tests were also carried out with different air gaps. The results showed a significant decrease in air permeability after deformation. However, the change of thickness was slight. The fabric deformation had a complicated effect on thermal protection with different air gaps. The change of TPP depended on the balance between the surface contact area and the thermal insulation. The newly developed testing apparatus could be well employed to evaluate the effect of deformation on TPP of flame-resistant fabrics. (paper)

  16. A new approach to characterize the effect of fabric deformation on thermal protective performance

    Science.gov (United States)

    Li, Jun; Li, Xiaohui; Lu, Yehu; Wang, Yunyi

    2012-04-01

    It is very important to evaluate thermal protective performance (TPP) in laboratory-simulated fire scenes as accurately as possible. For this paper, to thoroughly understand the effect of fabric deformation on basic physical properties and TPP of flame-retardant fabrics exposed to flash fire, a new modified TPP testing apparatus was developed. Different extensions were employed to simulate the various extensions displayed during different body motions. The tests were also carried out with different air gaps. The results showed a significant decrease in air permeability after deformation. However, the change of thickness was slight. The fabric deformation had a complicated effect on thermal protection with different air gaps. The change of TPP depended on the balance between the surface contact area and the thermal insulation. The newly developed testing apparatus could be well employed to evaluate the effect of deformation on TPP of flame-resistant fabrics.

  17. Children employed in the performing arts, advertising and fashion industry: what legal protection do they have?

    Science.gov (United States)

    Clin, Bénédicte; Ferrant, Ophélie; Marquignon, Marie-France; Letourneux, Marc

    2009-09-01

    Ill-treatment can sometimes take on an unfamiliar face. Particularly, this is the case for certain types of child employment. In France, as in most European countries, there are laws for protecting children and guaranteeing their right to schooling. Over and above the frequently observed apprenticeship contracts, obtained by eligible under 16 years, there is also the dispensatory case of children employed in the performing arts, advertising and the fashion industry. In France, legislators take the child's vulnerability into account when developing legislative and regulatory mechanisms, concerning the modalities of his/her professional activity, particularly in artistic fields and in fashion modelling. Since both may employ very young children, or even infants, one essential question ought to be raised: from a legal point of view, are these children sufficiently protected, with regard to the potential physical and psychological consequences of their particular professional activities?

  18. ‘Speaking Truth’ Protects Underrepresented Minorities’ Intellectual Performance and Safety in STEM

    Science.gov (United States)

    Ben-Zeev, Avi; Paluy, Yula; Milless, Katlyn L.; Goldstein, Emily J.; Wallace, Lyndsey; Márquez-Magaña, Leticia; Bibbins-Domingo, Kirsten; Estrada, Mica

    2017-01-01

    We offer and test a brief psychosocial intervention, Speaking Truth to EmPower (STEP), designed to protect underrepresented minorities’ (URMs) intellectual performance and safety in science, technology, engineering, and math (STEM). STEP takes a ‘knowledge as power’ approach by: (a) providing a tutorial on stereotype threat (i.e., a social contextual phenomenon, implicated in underperformance and early exit) and (b) encouraging URMs to use lived experiences for generating be-prepared coping strategies. Participants were 670 STEM undergraduates [URMs (Black/African American and Latina/o) and non-URMs (White/European American and Asian/Asian American)]. STEP protected URMs’ abstract reasoning and class grades (adjusted for grade point average [GPA]) as well as decreased URMs’ worries about confirming ethnic/racial stereotypes. STEP’s two-pronged approach—explicating the effects of structural ‘isms’ while harnessing URMs’ existing assets—shows promise in increasing diversification and equity in STEM. PMID:28835879

  19. 'Speaking Truth' Protects Underrepresented Minorities' Intellectual Performance and Safety in STEM.

    Science.gov (United States)

    Ben-Zeev, Avi; Paluy, Yula; Milless, Katlyn L; Goldstein, Emily J; Wallace, Lyndsey; Márquez-Magaña, Leticia; Bibbins-Domingo, Kirsten; Estrada, Mica

    2017-06-01

    We offer and test a brief psychosocial intervention, Speaking Truth to EmPower (STEP), designed to protect underrepresented minorities' (URMs) intellectual performance and safety in science, technology, engineering, and math (STEM). STEP takes a 'knowledge as power' approach by: (a) providing a tutorial on stereotype threat (i.e., a social contextual phenomenon, implicated in underperformance and early exit) and (b) encouraging URMs to use lived experiences for generating be-prepared coping strategies. Participants were 670 STEM undergraduates [URMs (Black/African American and Latina/o) and non-URMs (White/European American and Asian/Asian American)]. STEP protected URMs' abstract reasoning and class grades (adjusted for grade point average [GPA]) as well as decreased URMs' worries about confirming ethnic/racial stereotypes. STEP's two-pronged approach-explicating the effects of structural 'isms' while harnessing URMs' existing assets-shows promise in increasing diversification and equity in STEM.

  20. Evaluation of biofilm performance as a protective barrier against biocorrosion using an enzyme electrode.

    Science.gov (United States)

    Soleimani, S; Ormeci, B; Isgor, O B; Papavinasam, S

    2011-01-01

    Sulfide is known to be an important factor in microbiologically influenced corrosion (MIC) of metals and concrete deterioration in wastewater treatment structures and sewer pipelines. A sulfide biosensor was used to determine the effectiveness of Escherichia coli DH5 alpha biofilm as a protective barrier against MIC. The biofilm was shown to be effective in protecting surfaces from sulfide and helping to reduce MIC using amperometric measurements. The results also indicated that the growth conditions of E. coli DH5 alpha may have an impact on the performance of the biofilm as a sulfide barrier. The simple method provided in this work enables the comparison of several microbial biofilms and selection of the ones with potential to prevent MIC in a relatively short time.

  1. In-situ chemical reduction produced graphene paper for flexible supercapacitors with impressive capacitive performance

    Science.gov (United States)

    Ye, Xingke; Zhu, Yucan; Tang, Zhonghua; Wan, Zhongquan; Jia, Chunyang

    2017-08-01

    For practical applications of graphene-based materials in flexible supercapacitors, a technological breakthrough is currently required to fabricate high-performance graphene paper by a facile method. Herein, highly conductive (∼6900 S m-1) graphene paper with loose multilayered structure is produced by a high-efficiency in-situ chemical reduction process, which assembles graphite oxide suspensions into film and simultaneously conducts chemical reduction. Graphene papers with different parameters (including different types and doses of reductants, different thicknesses and areas of films) are successfully fabricated through this in-situ chemical reduction method. Meanwhile, the influences of the graphene papers with different parameters upon the supercapacitor performance are systematically investigated. Flexible supercapacitor based on the graphene paper exhibits high areal capacitance (152.4 mF cm-2 at current density of 2.0 mA cm-2 in aqueous electrolyte), and excellent rate performance (88.7% retention at 8.0 mA cm-2). Furthermore, bracelet-shaped all-solid supercapacitor with fascinating cycling stability (96.6% retention after 10 000 cycles) and electrochemical stability (an almost negligible capacity loss under different bending states and 99.6% retention after 4000 bending cycles) is established by employing the graphene paper electrode material and polymer electrolyte.

  2. Improved dental implant drill durability and performance using heat and wear resistant protective coatings.

    Science.gov (United States)

    Er, Nilay; Alkan, Alper; İlday, Serim; Bengu, Erman

    2018-03-02

    Dental implant drilling procedure is an essential step for implant surgery and frictional heat appeared in bone during drilling is a key factor affecting the success of an implant. The aim of this study is to increase the dental implant drill lifetime and performance using heat- and wear-resistant protective coatings hence to decrease the alveolar bone temperature caused by the dental implant drilling procedure. Commercially obtained stainless steel drills were coated with titanium aluminum nitride, diamond-like carbon, titanium boron nitride, and boron nitride coatings via magnetron-sputter deposition. Drilling procedure was performed on a bovine femoral cortical bone under the conditions mimicking clinical practice, where the tests were performed both under water-assisted cooling and under the conditions without any cooling was applied. Coated drill performances and durabilities were compared to that of three commonly used commercial drills which surfaces are made from namely; zirconia, black diamond and stainless steel. Protective coatings with boron nitride, titanium boron nitride and diamond-like carbon have significantly improved drill performance and durability. Especially boron nitride-coated drills have performed within safe bone temperature limits for 50 drillings even without any cooling is applied. Titanium aluminium nitride coated drills did not show any improvement over commercially obtained stainless steel drills. Surface modification using heat and wear resistant coatings is an easy and highly effective way to improve implant drill performance and durability, which can reflect positively on surgical procedure and healing period afterwards. The noteworthy success of different types of coatings is novel and likely to be applicable to various other medical systems.

  3. Evacuation of performance and significant chemical constituents and by products in drinking water treatment

    International Nuclear Information System (INIS)

    Jamrah, I. A.

    1999-01-01

    Drinking water treatment is a task that comprises of several processes that eventually lead to the addition of chemicals to achieve the objectives of treatment. This study was conducted to assess treatment performance, explain the presence of significant chemical species in water, and investigate the interactions and chemical by-products that are formed during the course of treatment. Grab water samples were collected on a regular basis from the influent and effluent of Zai water treatment plant. Chemical analysis were conducted to determine the concentrations of various chemical species of interest. Turbidity, temperature, and pH of the samples were also measured. The study concluded that Zai Water Treatment Plant produces potable drinking water in accordance with Jordanian Standards. The use of treatment chemical resulted in an increase in the concentrations of certain materials, such as manganese, aluminum, and sulfate. The turbidity of the raw water and the TOC of the samples were positively correlated, and the treatment results in approximately 20% TOC reduction, which demonstrates that the measures used for the control of TOC (carbon adsorption and permanganate pre-oxidation), are not very effective. The study also showed that the TOC content of our raw water samples and the concentration of tribalomethanes resulting after disinfection were positively correlated, and that bromoform was the dominant component. Also chloroform was the minor component of tribalomethanes formed during treatment. Positive correlation between the total concentration of tribalomethanes in water and the chlorine dose used for disinfection was also observed, and the total concentration of tribalomethanes increased with temperature. The formation of tribalomethanes was enhanced as the pH of water increased and as the concentration of bromide ion in raw water became significant. (author). 25 refs., 14 figs.1 table

  4. Corrosion protection performance of single and dual Plasma Electrolytic Oxidation (PEO) coating for aerospace applications

    International Nuclear Information System (INIS)

    Madhan Kumar, A.; Kwon, Sun Hwan; Jung, Hwa Chul; Shin, Kwang Seon

    2015-01-01

    Plasma Electrolytic Oxidation (PEO) coatings are known to be one of the most appropriate method for corrosion protection of magnesium (Mg) alloy. The improvement of PEO coatings and the optimization of their surface aspects are of major importance. In this current work, the influence of dual PEO coating on strip-cast AZ31 Mg alloy substrate has been evaluated with the aim of improving the surface and corrosion protection aspects. For this purpose, AZ31 Mg substrates are subjected to single and dual PEO processing in silicate and phosphate electrolyte under similar condition. Scanning electron microscopy (SEM) analysis confirmed that the number of pores in PEO coating processed in silicate electrolyte is higher than others. X-ray diffraction analysis of PEO coatings showed that the surface coating is mainly comprised of Mg 2 SiO 4 , Mg 3 (PO 4 ) 2 and MgO with different quantity based on PEO processing. Compared with the AZ31 Mg, the corrosion potential (E corr ) of both type PEO coatings was positively shifted about 250–400 mV and the corrosion current density (i corr ) was lowered by 3-4 orders of magnitude as result of adequate corrosion protection to the Mg alloy in 3.5% NaCl solution. All of the observation obviously showed that the dual PEO coating provides better corrosion protection performance than their respective single due to its synergistic beneficial effect. - Highlights: • Influence of dual PEO coating on AZ31 Mg alloy substrate was evaluated. • XRD confirmed formation of thin MgO inner, Mg 3 (PO 4 ) 2 and Mg 2 SiO 4 outer layer. • SEM results showed uniform coating with no cracks and relatively less micro pores. • Micro hardness of dual PEO coatings is higher than single PEO coatings. • Dual coating provides superior corrosion performance due to its synergistic effect

  5. Effect of Cation Ordering on the Performance and Chemical Stability of Layered Double Perovskite Cathodes

    Directory of Open Access Journals (Sweden)

    Carlos Bernuy-Lopez

    2018-01-01

    Full Text Available The effect of A-site cation ordering on the cathode performance and chemical stability of A-site cation ordered LaBaCo2O5+δ and disordered La0.5Ba0.5CoO3−δ materials are reported. Symmetric half-cells with a proton-conducting BaZr0.9Y0.1O3−δ electrolyte were prepared by ceramic processing, and good chemical compatibility of the materials was demonstrated. Both A-site ordered LaBaCo2O5+δ and A-site disordered La0.5Ba0.5CoO3−δ yield excellent cathode performance with Area Specific Resistances as low as 7.4 and 11.5 Ω·cm2 at 400 °C and 0.16 and 0.32 Ω·cm2 at 600 °C in 3% humidified synthetic air respectively. The oxygen vacancy concentration, electrical conductivity, basicity of cations and crystal structure were evaluated to rationalize the electrochemical performance of the two materials. The combination of high-basicity elements and high electrical conductivity as well as sufficient oxygen vacancy concentration explains the excellent performance of both LaBaCo2O5+δ and La0.5Ba0.5CoO3−δ materials at high temperatures. At lower temperatures, oxygen-deficiency in both materials is greatly reduced, leading to decreased performance despite the high basicity and electrical conductivity. A-site cation ordering leads to a higher oxygen vacancy concentration, which explains the better performance of LaBaCo2O5+δ. Finally, the more pronounced oxygen deficiency of the cation ordered polymorph and the lower chemical stability at reducing conditions were confirmed by coulometric titration.

  6. Justice perceptions of performance management practices in a company in the chemical industry

    Directory of Open Access Journals (Sweden)

    Thanasagree Govender

    2015-11-01

    Full Text Available The sustainability of corporations globally is becoming increasingly problematic. Combined with the unique challenges of an operating entity, this could potentially expose the profitability of sustainable businesses on a daily basis. The purpose of this study is to evaluate employees’ justice perceptions of performance management practices in a company in the chemical industry. The population includes all the employees in the chemical industry that was used in this study. A total of 140 questionnaires were issued to all the employees in an organisation which had undergone a performance appraisal and 102 respondents completed the surveys, giving a response rate of 72 per cent. A cross-sectional survey design was used in this study. The justice perceptions were measured according to an existing framework developed by Thurston and McNall (2010. The framework is founded on a hypothesised four-factor model constructed according to theories on organisational justice. The employees of the organisation in the chemical sector were involved in this study. Descriptive statistical analyses were used to measure perceptions of justice based on theories on organisational justice. The measuring instrument used was based on recognised models and theories. The study supports the construct validity of the measuring instrument and the reliability of the scales used. The justice constructs were used to identify specific items in the performance management practice that required improvement. The implications of the results are that continual interventions are required if employee commitment and productivity levels are to improve, resulting in a positive impact on business performance. Significant differences in perceptions by demographic groups were reported and discussed. This study explored the importance of understanding justice perceptions of performance management practices as an enabler for sustained business performance. Further, the study confirmed that

  7. NASA evaluation of Type 2 chemical depositions. [effects of deicer deposition on aircraft tire friction performance

    Science.gov (United States)

    Yager, Thomas J.; Stubbs, Sandy M.; Howell, W. Edward; Webb, Granville L.

    1993-01-01

    Recent findings from NASA Langley tests to define effects of aircraft Type 2 chemical deicer depositions on aircraft tire friction performance are summarized. The Aircraft Landing Dynamics Facility (ALDF) is described together with the scope of the tire cornering and braking friction tests conducted up to 160 knots ground speed. Some lower speed 32 - 96 km/hr (20 - 60 mph) test run data obtained using an Instrumented Tire Test Vehicle (ITTV) to determine effects of tire bearing pressure and transverse grooving on cornering friction performance are also discussed. Recommendations are made concerning which parameters should be evaluated in future testing.

  8. The use of chemical and radionuclide risk estimates in site performance evaluation of mixed waste sites

    International Nuclear Information System (INIS)

    Till, J.E.; Meyer, K.R.

    1988-01-01

    Many radioactive waste sites contain not only radioactive material but also varying amounts of chemical waste. The use of such procedures implies some risk at any exposure level, and thus requires that an exposure level be determined that corresponds to an acceptable risk to an individual or a population. Although the uncertainties and limitations of these methods are of concern, the assumption has been generally adopted that the human dose response for all carcinogens is linear, with no threshold occurring at low levels of exposure. With the move toward decontamination programs and clean-up of various mixed waste sites throughout the US, there is interest in the possibility that risk estimates calculated individually for radionuclides and for chemicals may be combined to reflect the total risk for each site. The purpose of this paper is to examine the feasibility of combining risk estimates during risk/benefit analyses. For a variety of reasons, the state of radiation risk assessment is more advanced than that of chemical risk assessment. The reasons for this disparity are summarized in this paper. Quantitative radiation risk assessment is currently being performed, but involves a high degree of uncertainty. Chemical risk assessment in general does not allow quantitative results bracketed by uncertainty analysis. Therefore, it is concluded that it is currently not possible to develop a useful, quantitative combined risk assessment for a mixed waste site, but that it may be possible to develop such a capability in the future

  9. Assessing the performance of Taiwan’s environmental protection system with a non-radial network DEA approach

    International Nuclear Information System (INIS)

    Huang, Chin-wei; Chiu, Yung-ho; Fang, Wei-ta; Shen, Neng

    2014-01-01

    Previous studies involving environmental performance purely focus on analyzing environmental or waste treatment efficiencies. This study combines various aspects of environmental protection and establishes a non-radial network DEA approach to evaluate the performance of an environmental protection system. The empirical methodology assumes that the system consists of three stages: administrative, executive processes, and protection effectiveness. The executive process includes waste treatment and pollution auditing divisions. In addition to assessing efficiencies, the empirical evaluation further explores the internal and external influences on performances and contributes implications and suggestions for environmental policy makers. The proposed model is utilized to gauge the performance of an environmental protection system for 20 municipalities in Taiwan. The results indicate the following: (1) for improving environmental quality, the government needs to put forth greater efforts in environmental audits; (2) improving productivity per unit so as to increase achievements in the executive process is more important for raising performance on environmental work, in addition to increasing workers and equipment for environmental protection; (3) a high degree of industrialization negatively influences administrative efficiency and educated residents have a greater comprehension for administrative operations, which can help in efficient budget utilization. - Highlights: • A non-radial network DEA approach to evaluate the Performance of Environmental Protection System. • The performance of waste treatment performs better than the efficiency of auditing. • Governmental expenditure is more efficiently utilized in the administrative process. • The effectiveness of achieved protection is a critical indicator for revealing environmental quality in a region

  10. Insulation Coordination of Arcing Horns on HVDC Electrode Lines: Protection Performance Evaluation, Influence Factors and Improvement Method

    Directory of Open Access Journals (Sweden)

    Xiandong Li

    2018-02-01

    Full Text Available Arcing horns are widely used in high voltage overhead lines to protect insulator strings from being destroyed by the free burning arcs caused by lightening faults. In this paper, we focus on the insulation coordination of arcing horns on the electrode lines of a 5000 MW, ±800 kV high voltage direct current (HVDC system. The protection performance of arcing horns are determined by the characteristics of not only the external system but also the fault arc. Therefore, the behaviors and characteristics of long free burning arcs are investigated by the experiments at first. In order to evaluate the protection performance of arcing horns, the static stability criterion U-I characteristic method is introduced. The influence factors on the protection performance of arcing horns are analyzed theoretically. Finally, the improvement methods for the protection performance of arcing horns are proposed, and the diversified configuration strategy of arcing horns is recommended for cost saving.

  11. Collective dose as a performance measure for occupational radiation protection programs: Issues and recommendations

    International Nuclear Information System (INIS)

    Strom, D.J.; Harty, R.; Hickey, E.E.; Martin, J.B.; Peffers, M.S.; Kathren, R.L.

    1998-07-01

    Collective dose is one of the performance measures used at many US Department of Energy (DOE) contractor facilities to quantitatively assess the objectives of the radiation protection program. It can also be used as a management tool to improve the program for keeping worker doses as low as reasonably achievable (ALARA). Collective dose is used here to mean the sum of all total effective dose equivalent values for all workers in a specified group over a specified time. It is often used as a surrogate estimate of radiological risk. In principle, improvements in radiation protection programs and procedures will result in reduction of collective dose, all other things being equal. Within the DOE, most frequently, a single collective dose number, which may or may not be adjusted for workload and other factors, is used as a performance measure for a contractor. The purpose of this report is to evaluate the use of collective dose as a performance measure for ALARA programs at DOE sites

  12. International comparisons of health system performance among OECD countries: opportunities and data privacy protection challenges.

    Science.gov (United States)

    Oderkirk, Jillian; Ronchi, Elettra; Klazinga, Niek

    2013-09-01

    Health data constitute a significant resource in most OECD countries that could be used to improve health system performance. Well-intended policies to allay concerns about breaches of confidentiality and to reduce potential misuse of personal health information may be limiting data use. A survey of 20 OECD countries explored the extent to which countries have developed and use personal health data and the reasons why data use may be problematic in some. Countries are divided, with one-half engaged regularly in national data linkage studies to monitor health care quality. Country variation is linked to risk management in granting an exemption to patient consent requirements; in sharing identifiable data among government authorities; and in project approvals and granting access to data. The resources required to comply with data protection requirements is a secondary problem. The sharing of person-level data across borders for international comparisons is rarely reported and there were few examples of studies of health system performance. Laws and policies enabling data sharing and data linkage are needed to strengthen national information infrastructure. To develop international studies comparing health care quality and health system performance, actions are needed to address heterogeneity in data protection practices. Copyright © 2013 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

  13. Performing Free Radioactive Certificate as an Effort to Protect Import and Export Commodities in Globalization Era

    International Nuclear Information System (INIS)

    Kunto-Wiharto; Syarbaini

    2001-01-01

    Several activities such as nuclear weapon tests, nuclear fuel reprocessing and nuclear accidents have caused radioactive contamination in local, regional and global environment. In globalization and free trade era, every country will be faced to the condition with the movable commodities from and to another countries. Global contamination through import and export commodities is a problem will be found every country in the future. Therefore, performing free radioactive certification on import and export commodities must be carried out to protect a member of public and environment from radioactive contamination. (author)

  14. Performance test of the prototype-unit for J-PARC machine protection system

    International Nuclear Information System (INIS)

    Sakaki, Hironao; Nakamura, Naoki; Takahashi, Hiroki; Yoshikawa, Hiroshi

    2004-03-01

    In High Intensity Proton Accelerator Project (J-PARC), the high-power proton beam is accelerated. If the beam in J-PARC is not stopped at a few micro seconds or less, the fatal thermal shock destruction is caused on the surface of accelerating structure, because of the high-power proton beam. To avoid the thermal shock damage, we designed the high-speed machine protection system. And, the prototype unit for the system was produced. This report shows the result of its performance test. (author)

  15. Equipment performance and radiation protection status in X-ray fluoroscopy units in Sudan

    International Nuclear Information System (INIS)

    Ahmed, N. A.; Nayl, A. I.; Suliman, I. I.

    2012-01-01

    The number of fluoroscopy and fluoroscopically guided procedures has been substantially growing in developing countries at the same time advanced and sophisticated equipment are used in some hospitals. However, radiation protection requirements are not necessarily well adopted. In this study nine fluoroscopy X-ray units in Sudan were examined for compliance with international standards. The tests included: beam quality, entrance surface air kerma, image quality and radiation field measurements. Staff radiation protection tools such as lead aprons and eye glasses were also visually examined to find out whether international recommendations were fulfilled and to determine the level of staff awareness. The measured peak tube voltage deviation exceeded the recommended tolerance level in 30 % of the measurements. The results of patient doses measurements exceeded the recommended reference dose levels in 43 % of the measurements; however image quality and radiation field generally fulfilled the requirements for most units. The study revealed that a considerable number of fluoroscopy units were not performing according to the international standards and highlights the need of optimisation of radiation protection. (authors)

  16. Influence of separate and combined impact both of radiation and chemical factors on state of lipid peroxide oxidation system and antioxidant protection at pregnant rats

    International Nuclear Information System (INIS)

    Danil'chik, V.S.; Spivak, L.V.; Kolb, V.G.; Zubovskaya, E.T.; Rogov, Yu.I.

    2000-01-01

    Influence of low dozed ionizing irradiation and chemical toxicant was studied both under separate and combined action in the process of pregnancy. The lipid peroxidation (LPO) indices and antioxidant protection (AOP) parameters of females rats were studied. The result received proved that irradiation during pregnancy induced activation both of lipids free radical oxidation and of antioxidant protection in female rats. Chemical toxicants introduction resulted in shifts on the LPO-AOP system the hydrogen peroxide blood level increasing and the antioxidants ones reducing. Combined action of both factors led to development of a new level of LPO-AOP

  17. Effect of Montmorillonite Nanogel Composite Fillers on the Protection Performance of Epoxy Coatings on Steel Pipelines.

    Science.gov (United States)

    Atta, Ayman M; El-Saeed, Ashraf M; Al-Lohedan, Hamad A; Wahby, Mohamed

    2017-06-02

    Montmorillonite (MMT) clay mineral is widely used as filler for several organic coatings. Its activity is increased by exfoliation via chemical modification to produce nanomaterials. In the present work, the modification of MMT to form nanogel composites is proposed to increase the dispersion of MMT into epoxy matrices used to fill cracks and holes produced by the curing exotherms of epoxy resins. The dispersion of MMT in epoxy improved both the mechanical and anti-corrosion performance of epoxy coatings in aggressive marine environments. In this respect, the MMT surfaces were chemically modified with different types of 2-acrylamido-2-methyl propane sulfonic acid (AMPS) nanogels using a surfactant-free dispersion polymerization technique. The effect of the chemical structure, nanogel content and the interaction with MMT surfaces on the surface morphology, surface charges and dispersion in the epoxy matrix were investigated for use as nano-filler for epoxy coatings. The modified MMT nanogel epoxy composites showed excellent resistance to mechanical damage and salt spray resistance up to 1000 h. The interaction of MMT nanogel composites with the epoxy matrix and good response of AMPS nanogel to sea water improve their ability to act as self-healing materials for epoxy coatings for steel.

  18. Assessment of skin exposure to N,N-dimethylformamide and methyl ethylketone through chemical protective gloves and decontamination of gloves for reuse purposes.

    Science.gov (United States)

    Chao, Keh-Ping; Wang, Ping; Chen, Chen-Peng; Tang, Ping-Yu

    2011-02-15

    N,N-dimethylformamide (DMF) and methyl ethylketone (MEK) are the hazardous chemicals commonly used in the synthetic leather industries. Although chemical protective gloves provide adequate skin exposure protection to workers in these industries, there is currently no clear guideline or understanding with regard to the use duration of these gloves. In this study, the permeation of DMF/MEK mixture through neoprene gloves and the desorption of chemicals from contaminated gloves were conducted using the ASTM F739 cell. The acceptable use duration time of the gloves against DMF/MEK permeation was estimated by assuming a critical body burden of chemical exposure as a result of dermal absorption. In a re-exposure cycle of 5 days, decontamination of the gloves by aeration at 25°C was found to be inadequate in a reduction of breakthrough time as compared to a new unexposed glove. However, decontamination of the gloves by heating at 70 or 100°C showed that the protective coefficient of the exposed gloves had similar levels of resistance to DMF/MEK as that of new gloves. Implications of this study include an understanding of the use duration of neoprene gloves and proper decontamination of chemical protective gloves for reuse. Copyright © 2010 Elsevier B.V. All rights reserved.

  19. Test Operations Procedure (TOP) 08-2-197 Chemical Protection Testing of Sorbent-Based Air Purification Components (APCs)

    Science.gov (United States)

    2016-06-24

    handling and storing the chemical materials of interest. Testing facilities intending to use chemical warfare agents (CWAs) and nontraditional agents...handling, and decontamination capabilities for research, development, test, and evaluation (RDT&E) quantities of chemical agents. Chemical agent...and decontaminated IAW the test plan and all test documentation will be archived. All recoverable chemical test materials will be accounted for and

  20. Concepts of skin protection: Considerations for the evaluation and terminology of the performance of skin protective equipment

    NARCIS (Netherlands)

    Brouwer, D.H.; Aitken, R.J.; Oppl, R.; Cherrie, J.W.

    2005-01-01

    This article proposes a common language for better understanding processes involved in dermal exposure and skin protection. A conceptual model has been developed that systematically describes the transport of agent mass from sources, eventually resulting in "loading" of the skin surface or the skin

  1. Thermal Protection Performance of Phase Changing Material Based on Polyethylene Glycol

    Directory of Open Access Journals (Sweden)

    Leila Sadat Ahmadi

    2012-12-01

    Full Text Available Phase change materials (PCM are substances with a high heat of fusion which, through melting and solidifying at certain temperatures, are capable to store or release a large amount of energy. This phenomenon can be utilized in designing heat protective materials as well as in thermal energy storage systems. One of the approaches to avoid materials leaching from a structure, where PCMs are incorporated, is to blend them with suitable polymers. To have a proper blend it is necessary to choose a compatible polymer with a PCM. It is important to assess the optimized concentration of PCM in polymer matrix and the phase structure and morphology of the blend, which causes the best heat protection. In this work, the influence of polyethylene glycol (PEG as PCMs in epoxy resin matrix on heat protection was investigated. A special performance test was designed to study timetemperature behavior of the prepared samples and DSC and SEM tests to observe the melting point, heat of fusion and morphology of the samples. The results indicated that increases in PCM content led to better heat protection and the best concentration for PEG was found to be 60% wt. Time-temperature curves show that increases of temperature for PCM samples is very slow compared with net epoxy sample. PCM samples curves show plateau in melting region. In this region, they show nearly 15°C temperature lower than a net epoxy sample. The plateau region makes a delay time in temperature increment, which is about 22 min for PEG samples compared with a net epoxy.

  2. Technical methods for a risk-informed, performance-based fire protection program at nuclear power plants

    International Nuclear Information System (INIS)

    Dey, M.K.

    1998-01-01

    This paper presents a technical review and examination of technical methods that are available for developing a risk-informed, performance-based fire protection program at a nuclear plant. The technical methods include ''engineering tools'' for examining the fire dynamics of fire protection problems, reliability techniques for establishing an optimal fire protection surveillance program, fire computer codes for analyzing important fire protection safety parameters, and risk-informed approaches that can range from drawing qualitative insights from risk information to quantifying the risk impact of alternative fire protection approaches. Based on this technical review and examination, it is concluded that methods for modeling fires, and reliability and fire PRA analyses are currently available to support the initial implementation of simple risk-informed, performance-based approaches in fire protection programs. (author)

  3. Technical methods for a risk-informed, performance-based fire protection program at nuclear power plants

    International Nuclear Information System (INIS)

    Dey, M.K.

    2000-01-01

    This paper presents a technical review and examination of technical methods that are available for developing a risk-informed, performance-based fire protection program at a nuclear plant. The technical methods include 'engineering tools' for examining the fire dynamics of fire protection problems, reliability techniques for establishing an optimal fire protection surveillance program, fire computer codes for analyzing important fire protection safety parameters, and risk-informed approaches that can range from drawing qualitative insights from risk information to quantifying the risk impact of alternative fire protection approaches. Based on this technical review and examination, it is concluded that methods for modeling fires, and reliability and fire probabilistic risk analyses (PRA) are currently available to support the initial implementation of simple risk-informed, performance-based approaches in fire protection programs. (orig.) [de

  4. Protection Performance Simulation of Coal Tar-Coated Pipes Buried in a Domestic Nuclear Power Plant Using Cathodic Protection and FEM Method

    Energy Technology Data Exchange (ETDEWEB)

    Chang, H. Y.; Lim, B. T.; Kim, K. S.; Kim, J. W.; Park, H. B. [KEPCO Engineering and Construction Company, Gimcheon (Korea, Republic of); Kim, Y. S.; Kim, K. T. [Andong National University, Andong (Korea, Republic of)

    2017-06-15

    Coal tar-coated pipes buried in a domestic nuclear power plant have operated under the cathodic protection. This work conducted the simulation of the coating performance of these pipes using a FEM method. The pipes, being ductile cast iron have been suffered under considerably high cathodic protection condition beyond the appropriate condition. However, cathodic potential measured at the site revealed non-protected status. Converting from 3D CAD data of the power plant to appropriate type for a FEM simulation was conducted and cathodic potential under the applied voltage and current was calculated using primary and secondary current distribution and physical conditions. FEM simulation for coal tar-coated pipe without defects revealed over-protection condition if the pipes were well-coated. However, the simulation for coal tar-coated pipes with many defects predict that the coated pipes may be severely degraded. Therefore, for high risk pipes, direct examination and repair or renewal of pipes are strongly recommended.

  5. Spectacle-related eye injuries, spectacle-impact performance and eye protection.

    Science.gov (United States)

    Hoskin, Annette K; Philip, Swetha; Dain, Stephen J; Mackey, David A

    2015-05-01

    The aim was to review the prevalence of spectacle-related ocular trauma and the performance of currently available spectacle materials and to identify the risk factors associated with spectacle-related ocular trauma. A literature review was conducted using Medline, Embase and Google with the keywords 'eyeglasses' OR 'spectacles' AND 'ocular injury' / 'eye injury'/ 'eye trauma' / 'ocular trauma'. Articles published prior to 1975 were excluded from this review because of advances in spectacle lens technology and Food and Drug Administration legislative changes requiring impact resistance of all prescription spectacle lenses in the United States. Six hundred and ninety-five individual ocular traumas, for which spectacles contributed to or were the main cause of injury, were identified in the literature. Eye injuries occurred when spectacles were worn in sports, in which medium- to high-impact energies were exerted from balls, racquets or bats and/or as a result of a collision with another player. Frame, lens design and product material choice were found to be associated with ocular injury, with polycarbonate lenses cited as the material of choice in the literature. International, regional and national standards for spectacle lenses had a wide range of impact requirements for prescription spectacle lenses, sports eye protection and occupational eye protection. Spectacle-related injury represents a small but preventable cause of ocular injury. With the increasing numbers of spectacle wearers and calls to spend more time outdoors to reduce myopia, spectacle wearers need to be made aware of the potential risks associated with wearing spectacles during medium- to high-risk activities. At particular risk are those prone to falls, the functionally one-eyed, those who have corneal thinning or have had previous eye surgery or injury. With increased understanding of specific risk factors, performance guidelines can be developed for prescription spectacle eye-protection

  6. Performance deficits following failure: learned helplessness or self-esteem protection?

    Science.gov (United States)

    Witkowski, T; Stiensmeier-Pelster, J

    1998-03-01

    We report two laboratory experiments which compare two competing explanations of performance deficits following failure: one based on Seligman's learned helplessness theory (LHT), and the other, on self-esteem protection theory (SEPT). In both studies, participants (Study 1: N = 40 pupils from secondary schools in Walbrzych, Poland; Study 2: N = 45 students from the University of Bielefeld, Germany) were confronted with either success or failure in a first phase of the experiment. Then, in the second phase of the experiment the participants had to work on a set of mathematical problems (Study 1) or a set of tasks taken from Raven's Progressive Matrices (Study 2) either privately or in public. In both studies failure in the first phase causes performance deficits in the second phase only if the participants had to solve the test tasks in public. These results were interpreted in line with SEPT and as incompatible with LHT.

  7. Ballistic Performance Model of Crater Formation in Monolithic, Porous Thermal Protection Systems

    Science.gov (United States)

    Miller, J. E.; Christiansen, E. L.; Deighton, K. D.

    2014-01-01

    Porous monolithic ablative systems insulate atmospheric reentry vehicles from reentry plasmas generated by atmospheric braking from orbital and exo-orbital velocities. Due to the necessity that these materials create a temperature gradient up to several thousand Kelvin over their thickness, it is important that these materials are near their pristine state prior to reentry. These materials may also be on exposed surfaces to space environment threats like orbital debris and meteoroids leaving a probability that these exposed surfaces will be below their prescribed values. Owing to the typical small size of impact craters in these materials, the local flow fields over these craters and the ablative process afford some margin in thermal protection designs for these locally reduced performance values. In this work, tests to develop ballistic performance models for thermal protection materials typical of those being used on Orion are discussed. A density profile as a function of depth of a typical monolithic ablator and substructure system is shown in Figure 1a.

  8. Lightning Protection Performance Assessment of Transmission Line Based on ATP model Automatic Generation

    Directory of Open Access Journals (Sweden)

    Luo Hanwu

    2016-01-01

    Full Text Available This paper presents a novel method to solve the initial lightning breakdown current by combing ATP and MATLAB simulation software effectively, with the aims to evaluate the lightning protection performance of transmission line. Firstly, the executable ATP simulation model is generated automatically according to the required information such as power source parameters, tower parameters, overhead line parameters, grounding resistance and lightning current parameters, etc. through an interface program coded by MATLAB. Then, the data are extracted from the generated LIS files which can be obtained by executing the ATP simulation model, the occurrence of transmission lie breakdown can be determined by the relative data in LIS file. The lightning current amplitude should be reduced when the breakdown occurs, and vice the verse. Thus the initial lightning breakdown current of a transmission line with given parameters can be determined accurately by continuously changing the lightning current amplitude, which is realized by a loop computing algorithm that is coded by MATLAB software. The method proposed in this paper can generate the ATP simulation program automatically, and facilitates the lightning protection performance assessment of transmission line.

  9. High performance In2O3 thin film transistors using chemically derived aluminum oxide dielectric

    KAUST Repository

    Nayak, Pradipta K.

    2013-07-18

    We report high performance solution-deposited indium oxide thin film transistors with field-effect mobility of 127 cm2/Vs and an Ion/Ioff ratio of 106. This excellent performance is achieved by controlling the hydroxyl group content in chemically derived aluminum oxide (AlOx) thin-film dielectrics. The AlOx films annealed in the temperature range of 250–350 °C showed higher amount of Al-OH groups compared to the films annealed at 500 °C, and correspondingly higher mobility. It is proposed that the presence of Al-OH groups at the AlOx surface facilitates unintentional Al-doping and efficient oxidation of the indium oxide channel layer, leading to improved device performance.

  10. High performance In2O3 thin film transistors using chemically derived aluminum oxide dielectric

    KAUST Repository

    Nayak, Pradipta K.; Hedhili, Mohamed N.; Cha, Dong Kyu; Alshareef, Husam N.

    2013-01-01

    We report high performance solution-deposited indium oxide thin film transistors with field-effect mobility of 127 cm2/Vs and an Ion/Ioff ratio of 106. This excellent performance is achieved by controlling the hydroxyl group content in chemically derived aluminum oxide (AlOx) thin-film dielectrics. The AlOx films annealed in the temperature range of 250–350 °C showed higher amount of Al-OH groups compared to the films annealed at 500 °C, and correspondingly higher mobility. It is proposed that the presence of Al-OH groups at the AlOx surface facilitates unintentional Al-doping and efficient oxidation of the indium oxide channel layer, leading to improved device performance.

  11. LCA of Chemicals and Chemical Products

    DEFF Research Database (Denmark)

    Fantke, Peter; Ernstoff, Alexi

    2018-01-01

    This chapter focuses on the application of Life Cycle Assessment (LCA) to evaluate the environmental performance of chemicals as well as of products and processes where chemicals play a key role. The life cycle stages of chemical products, such as pharmaceuticals drugs or plant protection products......, are discussed and differentiated into extraction of abiotic and biotic raw materials, chemical synthesis and processing, material processing, product manufacturing, professional or consumer product use, and finally end-of-life . LCA is discussed in relation to other chemicals management frameworks and concepts...... including risk assessment , green and sustainable chemistry , and chemical alternatives assessment. A large number of LCA studies focus on contrasting different feedstocks or chemical synthesis processes, thereby often conducting a cradle to (factory) gate assessment. While typically a large share...

  12. Confidentiality Protection of User Data and Adaptive Resource Allocation for Managing Multiple Workflow Performance in Service-Based Systems

    Science.gov (United States)

    An, Ho

    2012-01-01

    In this dissertation, two interrelated problems of service-based systems (SBS) are addressed: protecting users' data confidentiality from service providers, and managing performance of multiple workflows in SBS. Current SBSs pose serious limitations to protecting users' data confidentiality. Since users' sensitive data is sent in…

  13. Chemical and mechanical performance properties for various final waste forms -- PSPI scoping study

    International Nuclear Information System (INIS)

    Farnsworth, R.K.; Larsen, E.D.; Sears, J.W.; Eddy, T.L.; Anderson, G.L.

    1996-09-01

    The US DOE is obtaining data on the performance properties of the various final waste forms that may be chosen as primary treatment products for the alpha-contaminated low-level and transuranic waste at the INEL's Transuranic Storage Area. This report collects and compares selected properties that are key indicators of mechanical and chemical durability for Portland cement concrete, concrete formed under elevated temperature and pressure, sulfur polymer cement, borosilicate glass, and various forms of alumino-silicate glass, including in situ vitrification glass and various compositions of iron-enriched basalt (IEB) and iron-enriched basalt IV (IEB4). Compressive strength and impact resistance properties were used as performance indicators in comparative evaluation of the mechanical durability of each waste form, while various leachability data were used in comparative evaluation of each waste form's chemical durability. The vitrified waste forms were generally more durable than the non-vitrified waste forms, with the iron-enriched alumino-silicate glasses and glass/ceramics exhibiting the most favorable chemical and mechanical durabilities. It appears that the addition of zirconia and titania to IEB (forming IEB4) increases the leach resistance of the lanthanides. The large compositional ranges for IEB and IEB4 more easily accommodate the compositions of the waste stored at the INEL than does the composition of borosilicate glass. It appears, however, that the large potential variation in IEB and IEB4 compositions resulting from differing waste feed compositions can impact waste form durability. Further work is needed to determine the range of waste stream feed compositions and rates of waste form cooling that will result in acceptable and optimized IEB or IEB4 waste form performance. 43 refs

  14. Chemically Crosslinked Hydrogel Film Leads to Integrated Flexible Supercapacitors with Superior Performance.

    Science.gov (United States)

    Wang, Kai; Zhang, Xiong; Li, Chen; Sun, Xianzhong; Meng, Qinghai; Ma, Yanwei; Wei, Zhixiang

    2015-12-02

    A high-strength poly(vinyl alcohol) chemical hydrogel (PCH) film is prepared by coupling covalent crosslinking with a film-casting process. Conducting polyaniline (PANI) is then embedded in the PCH film by in situ growth to form a composite film with a PANI-hydrogel-PANI configuration, which leads to a new conceptual flexible supercapacitor with all-in-one configuration that exhibits superior electrochemical performance and mechanical flexibility. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Performance predictions for solar-chemical converters based on photoelectrochemical I-V curves

    Energy Technology Data Exchange (ETDEWEB)

    Luttmer, J.D.; Trachtenberg, I.

    1985-06-01

    Texas Instruments' solar energy system contains a solar-chemical converter (SCC) which converts solar energy into chemical energy via the electrolysis of hydrobromic acid (HBr) into hydrogen (H/sub 2/) and bromine (Br/sub 2/). Previous predictions of SCC performance have employed electrical dry-probe data and a computer simulation model to predict the H/sub 2/ generation rates. The method of prediction described here makes use of the photoelectrochemical Icurves to determine the ''wet'' probe parameters of V /SUB oc/ J /SUB sc/ FF, and efficiency for anodes and cathodes. The advantages of this technique over the dry-probe/computer simulation method are discussed. A comparison of predicted and measured H/sub 2/ generation rates is presented. Solar to chemical efficiencies of 8.6% have been both predicted and measured for the electrolysis of 48% HBr to hydrogen and bromine by a full anode/cathode array. Individual cathode solar to hydrogen efficiencies of 9.5% have been obtained.

  16. Performance of Chemically Treated Jute Geotextile in Unpaved Roads at Different in situ Conditions

    Science.gov (United States)

    Midha, Vinay Kumar; Joshi, Shubham; Suresh Kumar, S.

    2017-06-01

    Biodegradable jute geotextiles are an effective reinforcing material for unpaved roads, but its serviceability is limited because of faster microbial degradation. Different methods are in use to improve the serviceability of jute geotextiles. In this paper, influence of chemical treatment (transesterification and bitumen coating), road design and rainfall intensity on the time dependent serviceability of jute geotextiles has been studied. Chemically treated jute geotextiles, were laid in unpaved road designs with and without sand layer, for 30, 60 and 90 days' duration, and subjected to simulated rainfall intensities of 50 and 100 mm/h. With increase in time of usage, tensile strength and puncture resistance decrease due to microbial attack, and pore size decreases due to clogging of soil in jute geotextiles. Chemical treatment was observed to have greater influence on the serviceability, followed by the presence of sand layer in road design and the rainfall intensity. Further, overall performance of bitumen coated jute geotextiles was observed to be better than transesterified jute geotextile, due to its hydrophobic nature.

  17. Thermal buffering performance of composite phase change materials applied in low-temperature protective garments

    Science.gov (United States)

    Yang, Kai; Jiao, Mingli; Yu, Yuanyuan; Zhu, Xueying; Liu, Rangtong; Cao, Jian

    2017-07-01

    Phase change material (PCM) is increasingly being applied in the manufacturing of functional thermo-regulated textiles and garments. This paper investigated the thermal buffering performance of different composite PCMs which are suitable for the application in functional low-temperature protective garments. First, according to the criteria selecting PCM for functional textiles/garments, three kinds of pure PCM were selected as samples, which were n-hexadecane, n-octadecane and n-eicosane. To get the adjustable phase change temperature range and higher phase change enthalpy, three kinds of composite PCM were prepared using the above pure PCM. To evaluate the thermal buffering performance of different composite PCM samples, the simulated low-temperature experiments were performed in the climate chamber, and the skin temperature variation curves in three different low temperature conditions were obtained. Finally composite PCM samples’ thermal buffering time, thermal buffering capacity and thermal buffering efficiency were calculated. Results show that the comprehensive thermal buffering performance of n-octadecane and n-eicosane composite PCM is the best.

  18. Hot wire chemical vapor deposition: limits and opportunities of protecting the tungsten catalyzer from silicide with a cavity

    International Nuclear Information System (INIS)

    Frigeri, P.A.; Nos, O.; Bengoechea, S.; Frevert, C.; Asensi, J.M.; Bertomeu, J.

    2009-01-01

    Hot Wire Chemical Vapor Deposition (HW-CVD) is one of the most promising techniques for depositing the intrinsic microcrystalline silicon layer for the production of micro-morph solar cells. However, the silicide formation at the colder ends of the tungsten wire drastically reduces the lifetime of the catalyzer, thus limiting its industrial exploitation. A simple but interesting strategy to decrease the silicide formation is to hide the electrical contacts of the catalyzer in a long narrow cavity which reduces the probability of the silane molecules to reach the colder ends of the wire. In this paper, the working mechanism of the cavity is elucidated. Measurements of the thickness profile of the silicon deposited in the internal walls of the cavity have been compared with those predicted using a simple diffusion model based on the assumption of Knudsen flow. A lifetime study of the protected and unprotected wires has been carried out. The different mechanisms which determine the deterioration of the catalyzer have been identified and discussed.

  19. Micro-patterned ZnO semiconductors for high performance thin film transistors via chemical imprinting with a PDMS stamp.

    Science.gov (United States)

    Seong, Kieun; Kim, Kyongjun; Park, Si Yun; Kim, Youn Sang

    2013-04-07

    Chemical imprinting was conducted on ZnO semiconductor films via a chemical reaction at the contact regions between a micro-patterned PDMS stamp and ZnO films. In addition, we applied the chemical imprinting on Li doped ZnO thin films for high performance TFTs fabrication. The representative micro-patterned Li doped ZnO TFTs showed a field effect mobility of 4.2 cm(2) V(-1) s(-1) after sintering at 300 °C.

  20. Effect of Protectants on the Fermentation Performance of Wine Yeasts Subjected to Osmotic Stress

    Directory of Open Access Journals (Sweden)

    Andrea Caridi

    2003-01-01

    Full Text Available During alcoholic fermentation of must from dried grapes, yeasts are subjected to very high sugar concentrations, besides other environmental stresses, and they modify their metabolic behaviour giving low ethanol yield and abnormally high acetic acid production. To investigate the protective effect of catechin, inositol, and SO2 on wine yeasts, three thermotolerant strains of Saccharomyces cerevisiae, selected for wine making of must from dried grapes, and three strains of Saccharomyces selected for the production of wine, were inoculated in a sample of must at very high osmotic strength. A significant (p<0.01 or p<0.05 relationship between the addition of 100 mg/L of catechin, inositol or SO2 to the grape must and the change in the metabolic behaviour of the yeasts was observed. Compared to the control and depending on strain and protectant, the fermentation rate after 3 days increased up to 55 %, the ethanol content of the wines increased up to 16 %, the unitary succinic acid production increased up to 55 %, the unitary acetic acid production decreased up to 53 %, and the unitary glycerol production decreased up to 69 %. So by adding catechin, inositol or SO2 to the grape must it is possible to minimise the abnormal fermentation performance that wine yeasts exhibit in wine making of must from dried grapes.

  1. ‘Speaking Truth’ Protects Underrepresented Minorities’ Intellectual Performance and Safety in STEM

    Directory of Open Access Journals (Sweden)

    Avi Ben-Zeev

    2017-06-01

    Full Text Available We offer and test a brief psychosocial intervention, Speaking Truth to EmPower (STEP, designed to protect underrepresented minorities’ (URMs intellectual performance and safety in science, technology, engineering, and math (STEM. STEP takes a ‘knowledge as power’ approach by: (a providing a tutorial on stereotype threat (i.e., a social contextual phenomenon, implicated in underperformance and early exit and (b encouraging URMs to use lived experiences for generating be-prepared coping strategies. Participants were 670 STEM undergraduates [URMs (Black/African American and Latina/o and non-URMs (White/European American and Asian/Asian American]. STEP protected URMs’ abstract reasoning and class grades (adjusted for grade point average [GPA] as well as decreased URMs’ worries about confirming ethnic/racial stereotypes. STEP’s two-pronged approach—explicating the effects of structural ‘isms’ while harnessing URMs’ existing assets—shows promise in increasing diversification and equity in STEM.

  2. In-reactor performance of methods to control fuel-cladding chemical interaction

    International Nuclear Information System (INIS)

    Weber, E.T.; Gibby, R.L.; Wilson, C.N.; Lawrence, L.A.; Adamson, M.G.

    1979-01-01

    Inner surface corrosion of austenitic stainless steel cladding by oxygen and reactive fission product elements requires a 50 μm wastage allowance in current FBR reference oxide fuel pin design. Elimination or reduction of this wastage allowance could result in better reactor efficiency and economics through improvements in fuel pin performance and reliability. Reduction in cladding thickness and replacement of equivalent volume with fuel result in improved breeding capability. Of the factors affecting fuel-cladding chemical interaction (FCCI), oxygen activity within the fuel pin can be most readily controlled and/or manipulated without degrading fuel pin performance or significantly increasing fuel fabrication costs. There are two major approaches to control oxygen activity within an oxide fuel pin: (1) control of total oxygen inventory and chemical activity (Δ anti GO 2 ) by use of low oxygen-to-metal ratio (O/M) fuel; and (2) incorporation of a material within the fuel pin to provide in-situ control of oxygen activity (Δ anti GO 2 ) and fixation of excess oxygen prior to, or in preference to reaction with the cladding. The paper describes irradiation tests which were conducted in EBR-II and GETR incorporating oxygen buffer/getter materials and very low O/M fuel to control oxygen activity in sealed fuel pins

  3. Occupational allergic contact dermatitis caused by sterile non-latex protective gloves: clinical investigation and chemical analyses.

    Science.gov (United States)

    Pontén, Ann; Hamnerius, Nils; Bruze, Magnus; Hansson, Christer; Persson, Christina; Svedman, Cecilia; Thörneby Andersson, Kirsten; Bergendorff, Ola

    2013-02-01

    An increased frequency of occupational contact hand dermatitis among surgical operating theatre personnel has been noticed. To evaluate patients with occupational contact dermatitis caused by their rubber gloves, and to describe a method for analysing the content of the allergens in the gloves. Patch tests were performed with the baseline series, a rubber chemical series, and the patients' own gloves. A method for analysing 1,3-diphenylguanidine (DPG) and cetylpyridinium chloride in the gloves was developed. Contact allergy to thiuram mix was found in 8 of 16 patients, whereas 12 of 16 patients reacted to DPG. In 7 of 8 patients, contact allergy to cetylpyridinium chloride was found. In the patients' gloves, cetylpyridinium chloride and DPG were detected at higher concentrations on the inside of the gloves than on the outside. Most patients had worked for decades in their present occupations, but their hand dermatitis had only been present for months. Contact allergy to DPG in gloves has been disputed, but, in this study, we were able to confirm the presence of DPG and cetylpyridinium chloride in the causative gloves by using a modified method for the analysis. The presence of these chemicals in gloves caused an increase in occupational contact dermatitis in surgical operating theatre personnel. © 2012 John Wiley & Sons A/S.

  4. Potential application of ecological models in the European environmental risk assessment of chemicals. I. Review of protection goals in EU directives and regulations.

    Science.gov (United States)

    Hommen, Udo; Baveco, J M Hans; Galic, Nika; van den Brink, Paul J

    2010-07-01

    Several European directives and regulations address the environmental risk assessment of chemicals. We used the protection of freshwater ecosystems against plant protection products, biocidal products, human and veterinary pharmaceuticals, and other chemicals and priority substances under the Water Framework Directive as examples to explore the potential of ecological effect models for a refined risk assessment. Our analysis of the directives, regulations, and related guidance documents lead us to distinguish the following 5 areas for the application of ecological models in chemical risk assessment: 1) Extrapolation of organism-level effects to the population level: The protection goals are formulated in general terms, e.g., avoiding "unacceptable effects" or "adverse impact" on the environment or the "viability of exposed species." In contrast, most of the standard ecotoxicological tests provide data only on organism-level endpoints and are thus not directly linked to the protection goals which focus on populations and communities. 2) Extrapolation of effects between different exposure profiles: Especially for plant protection products, exposure profiles can be very variable and impossible to cover in toxicological tests. 3) Extrapolation of recovery processes: As a consequence of the often short-term exposures to plant protection products, the risk assessment is based on the community recovery principle. On the other hand, assessments under the other directives assume a more or less constant exposure and are based on the ecosystem threshold principle. 4) Analysis and prediction of indirect effects: Because effects on 1 or a few taxa might have consequences on other taxa that are not directly affected by the chemical, such indirect effects on communities have to be considered. 5) Prediction of bioaccumulation within food chains: All directives take the possibility of bioaccumulation, and thus secondary poisoning within the food chain, into account. (c) 2010 SETAC.

  5. Potential application of population models in the European ecological risk assessment of chemicals. II. Review of models and their potential to address environmental protection aims.

    Science.gov (United States)

    Galic, Nika; Hommen, Udo; Baveco, J M Hans; van den Brink, Paul J

    2010-07-01

    Whereas current chemical risk assessment (RA) schemes within the European Union (EU) focus mainly on toxicity and bioaccumulation of chemicals in individual organisms, most protection goals aim at preserving populations of nontarget organisms rather than individuals. Ecological models are tools rarely recommended in official technical documents on RA of chemicals, but are widely used by researchers to assess risks to populations, communities and ecosystems. Their great advantage is the relatively straightforward integration of the sensitivity of species to chemicals, the mode of action and fate in the environment of toxicants, life-history traits of the species of concern, and landscape features. To promote the usage of ecological models in regulatory risk assessment, this study tries to establish whether existing, published ecological modeling studies have addressed or have the potential to address the protection aims and requirements of the chemical directives of the EU. We reviewed 148 publications, and evaluated and analyzed them in a database according to defined criteria. Published models were also classified in terms of 5 areas where their application would be most useful for chemical RA. All potential application areas are well represented in the published literature. Most models were developed to estimate population-level responses on the basis of individual effects, followed by recovery process assessment, both in individuals and at the level of metapopulations. We provide case studies for each of the proposed areas of ecological model application. The lack of clarity about protection goals in legislative documents made it impossible to establish a direct link between modeling studies and protection goals. Because most of the models reviewed here were not developed for regulatory risk assessment, there is great potential and a variety of ecological models in the published literature. (c) 2010 SETAC.

  6. High performance shape annealing matrix (HPSAM) methodology for core protection calculators

    International Nuclear Information System (INIS)

    Cha, K. H.; Kim, Y. H.; Lee, K. H.

    1999-01-01

    In CPC(Core Protection Calculator) of CE-type nuclear power plants, the core axial power distribution is calculated to evaluate the safety-related parameters. The accuracy of the CPC axial power distribution highly depends on the quality of the so called shape annealing matrix(SAM). Currently, SAM is determined by using data measured during startup test and used throughout the entire cycle. An issue concerned with SAM is that it is fairly sensitive to measurements and thus the fidelity of SAM is not guaranteed for all cycles. In this paper, a novel method to determine a high-performance SAM (HPSAM) is proposed, where both measured and simulated data are used in determining SAM

  7. Brazilian industry evaluation system of performance on radiation protection in radioisotope gauges area

    International Nuclear Information System (INIS)

    Santos, Joyra A.; Borges, Jose C.

    1999-01-01

    The conventional industries more can see the advantages on doing their activities by using radioisotope gauges. This paper presents the methodology used to evaluation, by means of regulatory inspections, the performance on radiation protection of the Brazilian conventional industries in the field of radioisotope gauges. Sixty one inspections were analysed in the year of 1997 in these installations, taking into account the principal administrative and operational aspects. With the objective to have a final evaluation of the installation, it was given a value of each item of the inspection report, related of its importance. Finally, the values have been added and it had obtained a final evaluation, which has a range from 0 to 10 (poor or excellent). (author)

  8. Ballistic protection performance of curved armor systems with or without debondings/delaminations

    International Nuclear Information System (INIS)

    Tan, Ping

    2014-01-01

    Highlights: • Influence of pre-existing defect in an armor system on its ballistic performance. • Development of finite element models for the ballistic performance of armor systems. • Prediction of the ballistic limit and back face deformation of curved armor systems. - Abstract: In order to discern how pre-existing defects such as single or multiple debondings/delaminations in a curved armor system may affect its ballistic protection performance, two-dimensional axial finite element models were generated using the commercial software ANSYS/Autodyn. The armor systems considered in this investigation are composed of boron carbide front component and Kevlar/epoxy backing component. They are assumed to be perfectly bonded at the interface without defects. The parametric study shows that for the cases considered, the maximum back face deformation of a curved armor system with or without defects is more sensitive to its curvature, material properties of the ceramic front component, and pre-existing defect size and location than the ballistic limit velocity. Additionally, both the ballistic limit velocity and maximum back face deformation are significantly affected by the backing component thickness, front/backing component thickness ratio and the number of delaminations

  9. Fire Propagation Performance of Intumescent Fire Protective Coatings Using Eggshells as a Novel Biofiller

    Directory of Open Access Journals (Sweden)

    M. C. Yew

    2014-01-01

    Full Text Available This paper aims to synthesize and characterize an effective intumescent fire protective coating that incorporates eggshell powder as a novel biofiller. The performances of thermal stability, char formation, fire propagation, water resistance, and adhesion strength of coatings have been evaluated. A few intumescent flame-retardant coatings based on these three ecofriendly fire retardant additives ammonium polyphosphate phase II, pentaerythritol and melamine mixed together with flame-retardant fillers, and acrylic binder have been prepared and designed for steel. The fire performance of the coatings has conducted employing BS 476: Part 6-Fire propagation test. The foam structures of the intumescent coatings have been observed using field emission scanning electron microscopy. On exposure, the coated specimens’ B, C, and D had been certified to be Class 0 due to the fact that their fire propagation indexes were less than 12. Incorporation of ecofriendly eggshell, biofiller into formulation D led to excellent performance in fire stopping (index value, (I=4.3 and antioxidation of intumescent coating. The coating is also found to be quite effective in water repellency, uniform foam structure, and adhesion strength.

  10. Assessment of Stability and Energy Dissipation Performances of an Antifer Layer Protected Caisson

    Directory of Open Access Journals (Sweden)

    M. Sedat Kabdaşlı

    2015-08-01

    Full Text Available The present study intends to assess the stability and energy dissipation performances of a breakwater configuration (APC protected by an antifer layer. For comparison, an ordinary caisson (OC, which was 5% wider and 10% heavier, was also investigated. Physical models were implemented and tested under regular and irregular waves; and resulting linear and angular displacements were directly measured via a photogrammetric method. Additionally, wave forces and resulting horizontal displacements were estimated both from recorded pressure data and from individual incident waves by modified Goda method. To calculate the horizontal displacement, the estimated wave force time series were directly double-integrated, whilst the theoretical method proposed by Shimosako et al. (1994 were used on the individual force values. Although OC was tested under shorter durations and had a more favorable superstructure in terms of resisting forces, the results indicated that APC was significantly more stable. Energy dissipation performance of the tested configurations were quantified in terms of spectral averaged and phase resolved reflection coefficients, whereas antifer damage ratio was measured on a block-count basis. Results indicated that the APC configuration had an enhanced performance of dissipating the wave energy; moreover, the dissipated energy directly links to antifer damage ratio.

  11. Planning for risk-informed/performance-based fire protection at nuclear power plants. Final report

    International Nuclear Information System (INIS)

    Najafi, B.; Parkinson, W.J.; Lee, J.A.

    1997-12-01

    This document presents a framework for discussing issues and building consensus towards use of fire modeling and risk technology in nuclear power plant fire protection program implementation. The plan describes a three-phase approach: development of core technologies, implementation of methods, and finally, case studies and pilot applications to verify viability of such methods. The core technologies are defined as fire modeling, fire and system tests, use of operational data, and system and risk techniques. The implementation phase addresses the programmatic issues involved in implementing a risk-informed/performance-based approach in an integrated approach with risk/performance measures. The programmatic elements include: (1) a relationship with fire codes and standards development as defined by the ongoing effort of NFPA for development of performance-based standards; (2) the ability for NRC to undertake inspection and enforcement; and (3) the benefit to utilities in terms of cost versus safety. The case studies are intended to demonstrate applicability of single issue resolution while pilot applications are intended to check the applicability of the integrated program as a whole

  12. Sensitivity enhancement of chemically amplified resists and performance study using extreme ultraviolet interference lithography

    Science.gov (United States)

    Buitrago, Elizabeth; Nagahara, Seiji; Yildirim, Oktay; Nakagawa, Hisashi; Tagawa, Seiichi; Meeuwissen, Marieke; Nagai, Tomoki; Naruoka, Takehiko; Verspaget, Coen; Hoefnagels, Rik; Rispens, Gijsbert; Shiraishi, Gosuke; Terashita, Yuichi; Minekawa, Yukie; Yoshihara, Kosuke; Oshima, Akihiro; Vockenhuber, Michaela; Ekinci, Yasin

    2016-07-01

    Extreme ultraviolet lithography (EUVL, λ=13.5 nm) is the most promising candidate to manufacture electronic devices for future technology nodes in the semiconductor industry. Nonetheless, EUVL still faces many technological challenges as it moves toward high-volume manufacturing (HVM). A key bottleneck from the tool design and performance point of view has been the development of an efficient, high-power EUV light source for high throughput production. Consequently, there has been extensive research on different methodologies to enhance EUV resist sensitivity. Resist performance is measured in terms of its ultimate printing resolution, line width roughness (LWR), sensitivity [S or best energy (BE)], and exposure latitude (EL). However, there are well-known fundamental trade-off relationships (line width roughness, resolution and sensitivity trade-off) among these parameters for chemically amplified resists (CARs). We present early proof-of-principle results for a multiexposure lithography process that has the potential for high sensitivity enhancement without compromising other important performance characteristics by the use of a "Photosensitized Chemically Amplified Resist™" (PSCAR™). With this method, we seek to increase the sensitivity by combining a first EUV pattern exposure with a second UV-flood exposure (λ=365 nm) and the use of a PSCAR. In addition, we have evaluated over 50 different state-of-the-art EUV CARs. Among these, we have identified several promising candidates that simultaneously meet sensitivity, LWR, and EL high-performance requirements with the aim of resolving line space (L/S) features for the 7- and 5-nm logic node [16- and 13-nm half-pitch (HP), respectively] for HVM. Several CARs were additionally found to be well resolved down to 12- and 11-nm HP with minimal pattern collapse and bridging, a remarkable feat for CARs. Finally, the performance of two negative tone state-of-the-art alternative resist platforms previously investigated

  13. Sensitivity enhancement of chemically amplified resists and performance study using EUV interference lithography

    Science.gov (United States)

    Buitrago, Elizabeth; Nagahara, Seiji; Yildirim, Oktay; Nakagawa, Hisashi; Tagawa, Seiichi; Meeuwissen, Marieke; Nagai, Tomoki; Naruoka, Takehiko; Verspaget, Coen; Hoefnagels, Rik; Rispens, Gijsbert; Shiraishi, Gosuke; Terashita, Yuichi; Minekawa, Yukie; Yoshihara, Kosuke; Oshima, Akihiro; Vockenhuber, Michaela; Ekinci, Yasin

    2016-03-01

    Extreme ultraviolet lithography (EUVL, λ = 13.5 nm) is the most promising candidate to manufacture electronic devices for future technology nodes in the semiconductor industry. Nonetheless, EUVL still faces many technological challenges as it moves toward high-volume manufacturing (HVM). A key bottleneck from the tool design and performance point of view has been the development of an efficient, high power EUV light source for high throughput production. Consequently, there has been extensive research on different methodologies to enhance EUV resist sensitivity. Resist performance is measured in terms of its ultimate printing resolution, line width roughness (LWR), sensitivity (S or best energy BE) and exposure latitude (EL). However, there are well-known fundamental trade-off relationships (LRS trade-off) among these parameters for chemically amplified resists (CARs). Here we present early proof-of-principle results for a multi-exposure lithography process that has the potential for high sensitivity enhancement without compromising other important performance characteristics by the use of a Photosensitized Chemically Amplified Resist (PSCAR). With this method, we seek to increase the sensitivity by combining a first EUV pattern exposure with a second UV flood exposure (λ = 365 nm) and the use of a PSCAR. In addition, we have evaluated over 50 different state-of-the-art EUV CARs. Among these, we have identified several promising candidates that simultaneously meet sensitivity, LWR and EL high performance requirements with the aim of resolving line space (L/S) features for the 7 and 5 nm logic node (16 nm and 13 nm half-pitch HP, respectively) for HVM. Several CARs were additionally found to be well resolved down to 12 nm and 11 nm HP with minimal pattern collapse and bridging, a remarkable feat for CARs. Finally, the performance of two negative tone state-of-the-art alternative resist platforms previously investigated was compared to the CAR performance at and

  14. Possible Protective Effect of Low-dose Gamma Irradiation and Certain Natural Products on Chemically Induced Hepatotoxicity in Rats

    International Nuclear Information System (INIS)

    Rashed, R.R.A.

    2015-01-01

    Liver, the largest organ in the human body, is a vital organ that performs more than 500 vital metabolic functions. More than a 1000 drugs of the modern pharmacopoeia can induce liver injury with different clinical presentations. In the most severe cases, drug-induced liver injury may require liver transplantation or lead to death of the patient. Acetaminophen (acetyl-para-amino-phenol, paracetamol, APAP) is safe at therapeutic doses, but accidental or intentional overdose can induce severe hepatotoxicity in both humans and experimental animals. APAP-induced hepatotoxicity is dose related and reproducible in animals, and is thus widely used as a model for experimentally induced hepatotoxicity. Many herbs have been used as natural remedies for the prevention and/or treatment of liver diseases. Herbal drugs gained importance and popularity in recent years because of their safety, efficacy and cost effectiveness. Interestingly, exposure to a small dose or dose rate of radiation was reported to induce stress, perturbing homeostasis. Organisms respond adaptively to such disturbances. The mechanisms by which low-dose radiation (LDR) protects the cells or tissue against subsequent radiation- or drug-induced toxicities have been attributed to its stimulation of various protective molecules such as antioxidants and anti apoptotic. In the light of the above mentioned information, this study was constructed in order to investigate the mechanism(s) of the hepato protective effects offered by each of garlic oil (GO), black seed oil (BO) and sesame oil (SO) each alone or combined with low dose total body gamma (γ)-irradiation against APAP-induced hepatotoxicity in male albino Wistar rats. Preliminary pilot studies were performed prior to the main experimental work; in order to select the effective irradiation dose, the hepato protective natural products and the duration of their administration to be used in the main study. To carry out the main study, 96 rats were randomly

  15. International Research Project on the Effects of Chemical Ageing of Polymers on Performance Properties: Chemical and Thermal Analysis

    Science.gov (United States)

    Bulluck, J. W.; Rushing, R. A.

    1996-01-01

    Work during the past six months has included significant research in several areas aimed at further clarification of the aging and chemical failure mechanism of thermoplastics (PVDF or Tefzel) pipes. Among the areas investigated were the crystallinity changes associated with both the Coflon and Tefzel after various simulated environmental exposures using X-ray diffraction analysis. We have found that significant changes in polymer crystallinity levels occur as a function of the exposures. These crystallinity changes may have important consequences on the fracture, fatigue, tensile, and chemical resistance of the materials. We have also noted small changes in the molecular weight distribution. Again these changes may result in variations in the mechanical and chemical properties in the material. We conducted numerous analytical studies with methods including X-ray Diffraction, Gel Permeation Chromatography, Fourier Transform Infrared Spectroscopy, Ultra- Violet Scanning Analysis, GC/Mass Spectrometry, Differential Scanning Calorimetry and Thermomechanical Analysis. In the ultra-violet analysis we noted the presence of an absorption band indicative of triene formation. We investigated a number of aged samples of both Tefzel and Coflon that were forwarded from MERL. We also cast films at SWT and subjected these films to a refluxing methanol 1% ethylene diamine solution. An updated literature search was conducted using Dialog and DROLLS to identify any new papers that may have been published in the open literature since the start of this project. The updated literature search and abstracts are contained in the Appendix section of this report.

  16. The energetic performance of a novel hybrid solar thermal and chemical looping combustion plant

    International Nuclear Information System (INIS)

    Jafarian, Mehdi; Arjomandi, Maziar; Nathan, Graham J.

    2014-01-01

    Highlights: • A hybrid solar chemical looping combustion power cycle is reported. • The cycle is studied for two configurations, with and without an after-burner. • The oxygen carrier particles are used as storage medium for solar thermal energy. • Total solar shares of 41.4% and 60% are achieved with and without the after-burner. • Efficiencies of 50% and 44.0% are achieved with and without the after-burner. - Abstract: The overall energetic performance of a gas turbine combined cycle powered by a hybrid cycle between a solar thermal and a chemical looping combustion (CLC) system firing methane is reported for two configurations. In one case, the outlet from the air reactor is fed directly to a gas turbine, while in the other an after-burner, also firing methane, is added to increase the gas turbine inlet temperature. The cycle is simulated using Aspen Plus software for the average diurnal profile of normal irradiance for Port Augusta, South Australia. The first law efficiency, total solar absorption efficiency, average and peak fractional power boosts, total solar share, net solar to electrical efficiency, fraction of pressurised CO 2 , incremental CO 2 avoidance and the exergy efficiency for both cycles are reported. The calculations predict a first law efficiency of 50.0% for the cycle employing an after-burner, compared with 44.0% for that without the after-burner. However, this is achieved at the cost of decreasing the solar share from 60.0%, without the after-burner, to 41.4% with it. Also reported is the sensitivity analysis of performance to variations in key operating parameters. The sensitivity analysis shows that further improvements to the performance of the cycle are possible

  17. Gas separation performance of 6FDA-based polyimides with different chemical structures

    KAUST Repository

    Qiu, Wulin

    2013-10-01

    This work reports the gas separation performance of several 6FDA-based polyimides with different chemical structures, to correlate chemical structure with gas transport properties with a special focus on CO2 and CH 4 transport and plasticization stability of the polyimides membranes relevant to natural gas purification. The consideration of the other gases (He, O2 and N2) provided additional insights regarding effects of backbone structure on detailed penetrant properties. The polyimides studied include 6FDA-DAM, 6FDA-mPDA, 6FDA-DABA, 6FDA-DAM:DABA (3:2), 6FDA-DAM:mPDA (3:2) and 6FDA-mPDA:DABA (3:2). Both pure and binary gas permeation were investigated. The packing density, which is tunable by adjusting monomer type and composition of the various samples, correlated with transport permeability and selectivity. The separation performance of the polyimides for various gas pairs were also plotted for comparison to the upper bound curves, and it was found that this family of materials shows attractive performance. The CO 2 plasticization responses for the un-cross-linked polyimides showed good plasticization resistance to CO2/CH4 mixed gas with 10% CO2; however, only the cross-linked polyimides showed good plasticization resistance under aggressive gas feed conditions (CO 2/CH4 mixed gas with 50% CO2 or pure CO 2). For future work, asymmetric hollow fibers and carbon molecular sieve membranes based on the most attractive members of the family will be considered. © 2013 Elsevier Ltd. All rights reserved.

  18. Gender Differences in Risk/Protection Profiles for Low Academic Performance

    Science.gov (United States)

    Whitney, Stephen D.; Renner, Lynette M.; Herrenkohl, Todd I.

    2010-01-01

    Using holistic-interactionistic theory, the simultaneous nature of risk and protection factors for both males and females (age 6-11 in Wave 1) is examined using latent profile analysis (LPA). Risk/protection classes are estimated using multiple risk factor variables (e.g., physical child abuse) and multiple protective factors (e.g.,…

  19. Analytical template protection performance and maximum key size given a Gaussian-modeled biometric source

    NARCIS (Netherlands)

    Kelkboom, E.J.C.; Breebaart, Jeroen; Buhan, I.R.; Veldhuis, Raymond N.J.; Vijaya Kumar, B.V.K.; Prabhakar, Salil; Ross, Arun A.

    2010-01-01

    Template protection techniques are used within biometric systems in order to protect the stored biometric template against privacy and security threats. A great portion of template protection techniques are based on extracting a key from or binding a key to a biometric sample. The achieved

  20. Measurement of hearing protection devices performance in the workplace during full-shift working operations.

    Science.gov (United States)

    Nélisse, Hugues; Gaudreau, Marc-André; Boutin, Jérôme; Voix, Jérémie; Laville, Frédéric

    2012-03-01

    The effectiveness of hearing protection devices (HPDs), when used in workplace conditions, has been shown over the years to be usually lower than the labeled values obtained under well-controlled laboratory conditions. Causes for such discrepancies have been listed and discussed by many authors. This study is an attempt to understand the issues in greater details and quantify some of these factors by looking at the performance of hearing protectors as a function of time during full work shift conditions. A non-invasive field microphone in the real ear (F-MIRE)-based method has been developed for measuring the effectiveness of different HPDs as a function of time in the workplace. Details of the test procedures, the equipment used, and the post-processing operations are presented and discussed. The methodology was developed in such a way that a complete time and frequency representation are possible. The system was used on a total of 24 workers in eight different companies. Work shifts of up to 9-h long were recorded. Various types of earmuffs and one type of molded earplugs were tested. Attenuation data reported as a function of time showed, for most workers tested, considerable fluctuations over entire work shift periods. Parts of these fluctuations are attributed to variations in the low-frequency content in the noise (in particular for earmuffs) as well as poor insertion and/or fitting of earplugs. Lower performances than laboratory-based ones were once again observed for most cases tested but also, important left and right ear differences were obtained for many individuals. When reported as a function of frequency, the attenuation results suggested that the few approximations used to relate the measurements to subjective real-ear-attenuation-at-threshold (REAT) data were realistic. The use of individualized attenuation data and performance ratings for HPDs as well as a good knowledge of the ambient noise in the workplace are key ingredients when evaluating the

  1. Agronomic performance and soil chemical attributes in a banana tree orchard fertigated with humic substances

    Directory of Open Access Journals (Sweden)

    Diego Magalhães de Melo

    2016-12-01

    Full Text Available Fertigation with humic substances products has been adopted in commercial banana tree plantations. However, there are few studies on the procedure to confirm its technical feasibility. This study aimed at assessing the effects of fertigation with humic substances on the chemical attributes of a Dystric Densic Xantic Ferralsol cultivated with the 'BRS Princesa' banana tree cultivar and on the agronomic performance of the orchard. The experiment was conducted using a randomized blocks design, with six treatments and four replications. Treatments consisted of a monthly application of humic substances doses based on the commercially recommended reference dose for the banana plantation (12.09 kg ha-1 cycle-1. The doses used were equivalent to percentages of the reference dose (100 %, 150 %, 200 %, 250 % and 300 %, in addition to the control. No significant effects of the fertigation with humic substances that could justify the use of the product at the doses assessed were observed on the soil chemical attributes, banana growth and yield.

  2. Optical and Electrical Performance of ZnO Films Textured by Chemical Etching

    Directory of Open Access Journals (Sweden)

    Shiuh-Chuan HER

    2015-11-01

    Full Text Available Zinc oxide (ZnO films were prepared by radio frequency (RF magnetron sputtering on the glass substrate as transparent conductive oxide films. For silicon solar cells, a proper surface texture is essential to introduce light scattering and subsequent light trapping to enhance the current generation. In this study, the magnetron-sputtered ZnO films were textured by wet-chemical etching in diluted hydrochloric acid (HCl for better light scattering. The diffuse transmittance of the surface textured ZnO films was measured to evaluate the light scattering. The influence of hydrochloric acid concentration on the morphology, optical and electrical properties of the surface-textured ZnO film was investigated. The ZnO film etched in 0.05M HCl solution for 30 s exhibited average diffuse transmittance in the visible wavelength range of 9.52 % and good resistivity of 1.10 x 10-3 W×cm while the as-deposited ZnO film had average diffuse transmittance of 0.51 % and relatively high resistivity of 5.84 x 10-2 W×cm. Experimental results illustrated that the optical and electrical performance of ZnO films can be significantly improved by introducing the surface texture through the wet-chemical etching process.DOI: http://dx.doi.org/10.5755/j01.ms.21.4.9624

  3. Understanding performance properties of chemical engines under a trade-off optimization: Low-dissipation versus endoreversible model

    Science.gov (United States)

    Tang, F. R.; Zhang, Rong; Li, Huichao; Li, C. N.; Liu, Wei; Bai, Long

    2018-05-01

    The trade-off criterion is used to systemically investigate the performance features of two chemical engine models (the low-dissipation model and the endoreversible model). The optimal efficiencies, the dissipation ratios, and the corresponding ratios of the dissipation rates for two models are analytically determined. Furthermore, the performance properties of two kinds of chemical engines are precisely compared and analyzed, and some interesting physics is revealed. Our investigations show that the certain universal equivalence between two models is within the framework of the linear irreversible thermodynamics, and their differences are rooted in the different physical contexts. Our results can contribute to a precise understanding of the general features of chemical engines.

  4. Performance evaluation of the conventional Brazilian industries radiation protection in the small industrial gauges and industrial radiography areas

    International Nuclear Information System (INIS)

    Santos, Joyra Amaral dos

    1999-08-01

    This works evaluates by punctuation the performance in conventional Brazilian industries radiation protection area which make use of small industrial gauges and industrial radiography. It proposes, procedures for industry self-evaluation, besides a new radiation protection plans pattern for the small industrial gauges area. The data source where inspection reports of Dosimetry Radiation Protection Institute/Nuclear Energy Commission conventional Brazilian industries' radiation protection plans, beyond visitation to the inspection place. The performance evaluation has been realized both in the administrative and operational aspects of the industries. About of 60% of the industries have a satisfactory register control which does not happen to the operational control. The performance evaluation advantage is that industries may self-evaluate, foreseeing Dosimetry Radiation Protection Institute's regulation inspections, correcting its irregularities, automatically improving its services. The number of industries which have obtained satisfactory performance in both areas is below 70%, both in administrative and operational aspects. Such number can be considered a low one as it is radiation protection. The procedures propose in this work aim to improve such a situation. (author)

  5. Office of River Protection (ORP) Monthly Performance Report for July 2000

    International Nuclear Information System (INIS)

    WAGNILD, K.J.

    2000-01-01

    River Protection Project (RPP) performance for the month of July 2000 was very good. The most significant accomplishments that occurred during the month include the following: The Interim Stabilization Project pumped approximately 30,000 gallons from four tanks. Project-to-date (since June 1998) volume pumped is approximately 808,000 gallons. Five tanks have been interim stabilized this fiscal year, and tanks 241-S-106,241-U-103, and 241-U-105 are being evaluated to determine if the stabilization criteria have been met. Out of the 149 single-shell tanks (SSTs), 124 tanks have been stabilized. Pumping this waste from the single-shell tanks to more secure double-shell tanks (DSTs) supports stabilization of the waste tanks and mitigates leakage to the environment. The Interim Stabilization Project is planned to complete by September 2004. Waste Characterization obtained one grab sample in the month of July 2000. A total of 14 core samples, 12 grab samples, and 6 vapor samples have been taken fiscal year-to-date (FYTD) in support of three key FY 2000 sampling milestones. The Waste Treatment Plant Design and Operation organizations have been developed and staffed, including transitioning BNFL Inc./Bechtel National Inc. employees to CHG. Since the termination of the BNFL contract, CHG has temporarily assumed the work scope for design and operation of the Waste Treatment Plant. A new waste treatment facility will be built at the Hanford Site in which highly radioactive waste from the tanks will be turned into glass and permanently stored. Approval of the Notice of Construction (NOC) for the AN Farm tank retrieval system was received from the U.S. Department of Energy (DOE) and the Environmental Protection Agency on July 21,2000. This is a significant step forward for Project W-211, ''Initial Tank Retrieval Systems'' in preparing waste for delivery to the Waste Treatment Plant

  6. Under pressure: evolutionary engineering of yeast strains for improved performance in fuels and chemicals production.

    Science.gov (United States)

    Mans, Robert; Daran, Jean-Marc G; Pronk, Jack T

    2018-04-01

    Evolutionary engineering, which uses laboratory evolution to select for industrially relevant traits, is a popular strategy in the development of high-performing yeast strains for industrial production of fuels and chemicals. By integrating whole-genome sequencing, bioinformatics, classical genetics and genome-editing techniques, evolutionary engineering has also become a powerful approach for identification and reverse engineering of molecular mechanisms that underlie industrially relevant traits. New techniques enable acceleration of in vivo mutation rates, both across yeast genomes and at specific loci. Recent studies indicate that phenotypic trade-offs, which are often observed after evolution under constant conditions, can be mitigated by using dynamic cultivation regimes. Advances in research on synthetic regulatory circuits offer exciting possibilities to extend the applicability of evolutionary engineering to products of yeasts whose synthesis requires a net input of cellular energy. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  7. Computer-Aided Chemical Product Design Framework: Design of High Performance and Environmentally Friendly Refrigerants

    DEFF Research Database (Denmark)

    Cignitti, Stefano; Zhang, Lei; Gani, Rafiqul

    properties and needs should carefully be selected for a given heat pump cycle to ensure that an optimum refrigerant is found? How can cycle performance and environmental criteria be integrated at the product design stage and not in post-design analysis? Computer-aided product design methods enable...... the possibility of designing novel molecules, mixtures and blends, such as refrigerants through a systematic framework (Cignitti et al., 2015; Yunus et al., 2014). In this presentation a computer-aided framework is presented for chemical product design through mathematical optimization. Here, molecules, mixtures...... and blends, are systematically designed through a decomposition based solution method. Given a problem definition, computer-aided molecular design (CAMD) problem is defined, which is formulated into a mixed integer nonlinear program (MINLP). The decomposed solution method then sequentially divides the MINLP...

  8. Nitric Oxide Release for Improving Performance of Implantable Chemical Sensors - A Review.

    Science.gov (United States)

    Cha, Kyoung Ha; Wang, Xuewei; Meyerhoff, Mark E

    2017-12-01

    Over the last three decades, there has been extensive interest in developing in vivo chemical sensors that can provide real-time measurements of blood gases (oxygen, carbon dioxide, and pH), glucose/lactate, and potentially other critical care analytes in the blood of hospitalized patients. However, clot formation with intravascular sensors and foreign body response toward sensors implanted subcutaneously can cause inaccurate analytical results. Further, the risk of bacterial infection from any sensor implanted in the human body is another major concern. To solve these issues, the release of an endogenous gas molecule, nitric oxide (NO), from the surface of such sensors has been investigated owing to NO's ability to inhibit platelet activation/adhesion, foreign body response and bacterial growth. This paper summarizes the importance of NO's therapeutic potential for this application and reviews the publications to date that report on the analytical performance of NO release sensors in laboratory testing and/or during in vivo testing.

  9. Chemical principles underpinning the performance of the metal–organic framework HKUST-1

    Science.gov (United States)

    Hendon, Christopher H.

    2015-01-01

    A common feature of multi-functional metal–organic frameworks is a metal dimer in the form of a paddlewheel, as found in the structure of Cu3(btc)2 (HKUST-1). The HKUST-1 framework demonstrates exceptional gas storage, sensing and separation, catalytic activity and, in recent studies, unprecedented ionic and electrical conductivity. These results are a promising step towards the real-world application of metal–organic materials. In this perspective, we discuss progress in the understanding of the electronic, magnetic and physical properties of HKUST-1, representative of the larger family of Cu···Cu containing metal–organic frameworks. We highlight the chemical interactions that give rise to its favourable properties, and which make this material well suited to a range of technological applications. From this analysis, we postulate key design principles for tailoring novel high-performance hybrid frameworks. PMID:28706713

  10. Chemical principles underpinning the performance of the metal-organic framework HKUST-1.

    Science.gov (United States)

    Hendon, Christopher H; Walsh, Aron

    2015-07-15

    A common feature of multi-functional metal-organic frameworks is a metal dimer in the form of a paddlewheel, as found in the structure of Cu 3 ( btc ) 2 (HKUST-1). The HKUST-1 framework demonstrates exceptional gas storage, sensing and separation, catalytic activity and, in recent studies, unprecedented ionic and electrical conductivity. These results are a promising step towards the real-world application of metal-organic materials. In this perspective, we discuss progress in the understanding of the electronic, magnetic and physical properties of HKUST-1, representative of the larger family of Cu···Cu containing metal-organic frameworks. We highlight the chemical interactions that give rise to its favourable properties, and which make this material well suited to a range of technological applications. From this analysis, we postulate key design principles for tailoring novel high-performance hybrid frameworks.

  11. Performance and cost of energy transport and storage systems for dish applications using reversible chemical reactions

    Science.gov (United States)

    Schredder, J. M.; Fujita, T.

    1984-01-01

    The use of reversible chemical reactions for energy transport and storage for parabolic dish networks is considered. Performance and cost characteristics are estimated for systems using three reactions (sulfur-trioxide decomposition, steam reforming of methane, and carbon-dioxide reforming of methane). Systems are considered with and without storage, and in several energy-delivery configurations that give different profiles of energy delivered versus temperature. Cost estimates are derived assuming the use of metal components and of advanced ceramics. (The latter reduces the costs by three- to five-fold). The process that led to the selection of the three reactions is described, and the effects of varying temperatures, pressures, and heat exchanger sizes are addressed. A state-of-the-art survey was performed as part of this study. As a result of this survey, it appears that formidable technical risks exist for any attempt to implement the systems analyzed in this study, especially in the area of reactor design and performance. The behavior of all components and complete systems under thermal energy transients is very poorly understood. This study indicates that thermochemical storage systems that store reactants as liquids have efficiencies below 60%, which is in agreement with the findings of earlier investigators.

  12. 10 CFR 73.25 - Performance capabilities for physical protection of strategic special nuclear material in transit.

    Science.gov (United States)

    2010-01-01

    ... strategic special nuclear material in transit. 73.25 Section 73.25 Energy NUCLEAR REGULATORY COMMISSION... Transit § 73.25 Performance capabilities for physical protection of strategic special nuclear material in transit. (a) To meet the general performance objective and requirements of § 73.20 an in-transit physical...

  13. Improvement in high-voltage and high rate cycling performance of nickel-rich layered cathode materials via facile chemical vapor deposition with methane

    International Nuclear Information System (INIS)

    Hyuk Son, In; Park, Kwangjin; Hwan Park, Jong

    2017-01-01

    Nickel-rich layered-oxide materials are considered promising candidates for application as cathode material in high-energy lithium ion batteries. However, their cycling performance at high voltages and rate conditions require further improvement for the purpose of commercialization. Here, we report on the facile surface modification of nickel-rich layered oxide by chemical vapor deposition with methane which yields a conductive and protective artificial solid electrolyte interphase layer consisting of amorphous carbon, alkyl lithium carbonate, and lithium carbonate. We examine the mechanism of the protective layer formation and structural deformation of the nickel-rich layered oxide during chemical vapor deposition with methane. Via optimizing the reaction conditions, we improve the electrical conductivity as well as the interfacial stability of the nickel-rich layered oxide without inducing structural deformation. The surface-modified nickel-rich layered oxide exhibits an improved performance due to the resulting enhanced rate capability, high initial efficiency, and long cycle life at high voltage (>4.5 V).

  14. Chemical buffering in natural and engineered barrier systems: Thermodynamic constraints and performance assessment consequences

    International Nuclear Information System (INIS)

    Arthur, R.C.; Wei Zhou

    2000-12-01

    Thermodynamic and kinetic constraints on the chemical buffering properties of natural and engineered-barrier systems are derived in this study from theoretical descriptions, incorporated in the reaction-path model, of reversible and irreversible mass transfer in multicomponent, multiphase systems. The buffering properties of such systems are conditional properties because they refer to a specific aqueous species in a system that is open with respect to a specific reactant. The solution to a mathematical statement of this concept requires evaluation of the dependence of the activity of the buffered species on incremental changes in the overall reaction-progress variable. This dependence can be represented by a truncated Taylor's series expansion, where the values of associated derivatives are calculated using finite-difference techniques and mass-balance, charge-balance and mass-action constraints. Kinetic constraints on buffering behavior can also be described if the relation between reactant flux and reaction rate is well defined. This relation is explicit for the important case of advective groundwater flow and water-rock interaction. We apply the theoretical basis of the chemical buffering concept to processes that could affect the performance of a deep geologic repository for nuclear waste. Specifically, we focus on the likelihood that an inverse relation must exist between the buffer intensity and the migration velocity of reaction fronts in systems involving advective or diffusive mass transport. A quantitative understanding of this relation would provide the basis for evaluating the potential role of chemical buffering in achieving the isolation and retardation functions, of the EBS and geosphere in a KBS-3 repository. Our preliminary evaluation of this role considers the effects of chemical buffering on the propagation velocity of a pH front in both the near- and far field. We use a geochemical modeling technique compatible with the reaction-path model to

  15. QUALITY ASSURANCE GUIDELINES FOR LABORATORIES PERFORMING FORENSIC ANALYSIS OF CHEMICAL TERRORISM

    Science.gov (United States)

    The Scientific Working Group on Forensic Analysis of Chemical Terrorism (SWGFACT) has developed the following quality assurance guidelines to provide laboratories engaged in forensic analysis of chemical evidence associated with terrorism a framework to implement a quality assura...

  16. Performance study of protective clothing against hot water splashes: from bench scale test to instrumented manikin test.

    Science.gov (United States)

    Lu, Yehu; Song, Guowen; Wang, Faming

    2015-03-01

    Hot liquid hazards existing in work environments are shown to be a considerable risk for industrial workers. In this study, the predicted protection from fabric was assessed by a modified hot liquid splash tester. In these tests, conditions with and without an air spacer were applied. The protective performance of a garment exposed to hot water spray was investigated by a spray manikin evaluation system. Three-dimensional body scanning technique was used to characterize the air gap size between the protective clothing and the manikin skin. The relationship between bench scale test and manikin test was discussed and the regression model was established to predict the overall percentage of skin burn while wearing protective clothing. The results demonstrated strong correlations between bench scale test and manikin test. Based on these studies, the overall performance of protective clothing against hot water spray can be estimated on the basis of the results of the bench scale hot water splashes test and the information of air gap size entrapped in clothing. The findings provide effective guides for the design and material selection while developing high performance protective clothing. Published by Oxford University Press on behalf of the British Occupational Hygiene Society 2014.

  17. An assessment of radiographers’ technical and protective performance in hospitals affiliated to Birjand University of Medical Sciences in 2012

    Directory of Open Access Journals (Sweden)

    Mahmood Reza Tavakkoli

    2014-08-01

    Materials and Methods: In this descriptive-analytical study, all the 26 radiolographers working in the radiology wards of Vali-asr and Imam Reza hospitals of Birjand participated. In order to collect data about their performance, a checklist whose reliability and validity had been approved was provided. For the radiography staff 17 technical and 12 protective items during three work shifts were checked and recorded. In order to measure their awareness of technical and protective principles, a 12-item questionnaire was completed by each of them. The obtained data was statistically analyzed by means of SPSS software using X2. Results: Mean Performance score in the technical area in the three work shifts was 15±1.60, and that of the protective area was 10.9±1.1 both of which were at an average level. Around 46.5% of the subjects gave correct answers to protective and 37.2% of them to the technical questions. The comparison of technical and protective performance scores showed no significant difference in terms of work shifts, education, gender, and type of employment (P>0.05. Conclusion: The radiographers’ awareness of technical and protective principles was at a very low level. Therefore, both quality academic training and in-service education seem necessary.

  18. Chemical Technology Division Comprehensive Self-Assessment and Upgrade Program (CSAUP). Performance Objectives and Criteria

    International Nuclear Information System (INIS)

    1990-05-01

    The U.S. Department of Energy (DOE) has placed strong emphasis on a new way of doing business patterned on the lessons learned in the nuclear power industry after the accident at Three Mile Island Unit 2. The new way relies on strict adherence to policies and procedures, a greatly expanded training program, and much more rigor and formality in operations. Another key element is more visible oversight by upper management and auditability by DOR Although the Chemical Technology Division (Chem Tech) has functioned in a safe manner since its beginning, the policies and methods of the past are no longer appropriate. Therefore, in accordance with these directives, Chem Tech is improving its operational performance by making a transition to greater formality in the observance of policies and procedures and a more deliberate consideration of the interrelationships between organizations at ORNL. This transition to formality is vitally important because both our staff and our facilities are changing with time. For example, some of the inventors and developers of the processes and facilities in use are now ''passing the torch'' to the next generation of Chem Tech staff. Our faculties have also served us well for many years, but the newest of these are now over 20 years old. All have increasing needs of refurbishment and repair, and some of the older ones need to be replaced. The Comprehensive Self-Assessment and Upgrade Program (CSAUP) has been patterned on a similar activity performed at the High Flux Isotope Reactor. Using the Draft DOE Performance Objectives and Criteria for Technical Safety Appraisals (May 1987) as a starting point, it was determined that 14 functional areas for evaluation listed in the report were suitable for Chem Tech use. An additional 5 functional areas were added for completeness since Chem Tech has a broader set of missions than a reactor facility. The Performance Objectives and Criteria (POC) for each functional area in the DOE report were

  19. Effects of Pluronic F-68 on Tetrahymena cells: protection against chemical and physical stress and prolongation of survival under toxic conditions

    DEFF Research Database (Denmark)

    Hellung-Larsen, P; Assaad, F; Pankratova, Stanislava

    2000-01-01

    exposed to hyperthermia (43 degrees C). The cellular survival is increased at reduced temperatures (e.g. 4 degrees C instead of 36 degrees C) and at increased cellular concentrations (e.g. 100 cells ml(-1) instead of 25 or 10 cells ml(-1)). There is no effect of pre-incubation with Pluronic......The effects of the non-ionic surfactant Pluronic F-68 (0.01% w/v) on Tetrahymena cells have been studied. A marked protection against chemical and physical stress was observed. The chemical stress effects were studied in cells suspended in buffer (starvation) or in buffers with added ingredients....... The protective effect of Pluronic towards Tetrahymena is observed for concentrations in the range from 0.001 to 0.1% w/v....

  20. Performance Improvement of the Core Protection Calculator System (CPCS) by Introducing Optimal Function Sets

    International Nuclear Information System (INIS)

    Won, Byung Hee; Kim, Kyung O; Kim, Jong Kyung; Kim, Soon Young

    2012-01-01

    The Core Protection Calculator System (CPCS) is an automated device which is adopted to inspect the safety parameters such as Departure from Nuclear Boiling Ratio (DNBR) and Local Power Density (LPD) during normal operation. One function of the CPCS is to predict the axial power distributions using function sets in cubic spline method. Another function of that is to impose penalty when the estimated distribution by the spline method disagrees with embedded data in CPCS (i.e., over 8%). In conventional CPCS, restricted function sets are used to synthesize axial power shape, whereby it occasionally can draw a disagreement between synthesized data and the embedded data. For this reason, the study on improvement for power distributions synthesis in CPCS has been conducted in many countries. In this study, many function sets (more than 18,000 types) differing from the conventional ones were evaluated in each power shape. Matlab code was used for calculating/arranging the numerous cases of function sets. Their synthesis performance was also evaluated through error between conventional data and consequences calculated by new function sets

  1. Effect of feeding rumen-protected methionine on productive and reproductive performance of dairy cows.

    Science.gov (United States)

    Toledo, Mateus Z; Baez, Giovanni M; Garcia-Guerra, Alvaro; Lobos, Nelson E; Guenther, Jerry N; Trevisol, Eduardo; Luchini, Daniel; Shaver, Randy D; Wiltbank, Milo C

    2017-01-01

    The objectives of this study were to evaluate the effects of daily top-dressing (individually feeding on the top of the total mixed ration) with rumen-protected methionine (RPM) from 30 ± 3 until 126 ± 3 Days in milk on productive and reproductive performance in lactating dairy cows. A total of 309 lactating dairy Holstein cows (138 primiparous and 171 multiparous) were randomly assigned to treatment diets containing either RPM (21.2 g of RPM + 38.8 g of dried distillers grain; 2.34% Methionine [Met] of metabolizable protein [MP]) or Control (CON; 60 g of dried distillers grain; 1.87% Met of MP). Plasma amino acids were evaluated at the time of artificial insemination (AI) and near pregnancy diagnosis. Milk production and milk composition were evaluated monthly. Pregnancy was diagnosed on Day 28 (by Pregnancy-specific protein B [PSPB]), 32, 47, and 61 (by ultrasound) and sizes of embryonic and amniotic vesicle were determined by ultrasound on Day 33 after AI. Feeding RPM increased plasma Met at 6, 9, 12, and 18 hours after top-dressing with a peak at 12 hours (52.4 vs 26.0 μM; P maintenance in multiparous cows. Further studies are needed to confirm these responses and understand the biological mechanisms that underlie these responses as well as the timing and concentrations of circulating Met that are needed to produce this effect.

  2. Collaborative Measurement of Performance of Jointly Managed Protected Areas in Northern Australia

    Directory of Open Access Journals (Sweden)

    Natasha Stacey

    2013-03-01

    Full Text Available Responsibility for the management of many protected areas in the Northern Territory, Australia, is shared between the management agency and the aboriginal owners of that land. We describe (1 the creation and types of indicators developed by partners in a participatory process to measure management effectiveness, (2 the assessment method used to monitor progress, and (3 the results of the first cycle of evaluations in four jointly managed parks. Although each pilot park area has distinctive features, we were able to identify a set of twelve common indicators that were applied across the four park areas. The agreed indicators, which were scored using a color scale to indicate level of achievement, were primarily concerned with process rather than outcome, with particular emphasis on the strength of social relationships. Thus, there were indicators that assessed performance in governance and decision making, application and interpretation of cultural heritage and traditional ecological knowledge, expansion of social capital, human and financial resources, and visitors, with little emphasis on the biophysical outcomes of the management. The emphasis on the quality of the process of joint management was thought to indicate that the relationship between the joint management partners was relatively new, with trust only starting to develop. We discuss opportunities and difficulties for replication and adaptation of indicators to all jointly managed parks in the Northern Territory.

  3. Enhanced Performance of Thin Film Composite Forward Osmosis Membrane by Chemical Post-Treatment

    Science.gov (United States)

    Liu, Zheng; Chen, Jiangrong; Cao, Zhen; Wang, Jian; Guo, Chungang

    2018-01-01

    Forward osmosis is an attractive technique in water purification and desalination fields. Enhancement of the forward osmosis membrane performance is essential to the application of this technique. In this study, an optimized chemical post-treatment approach which was used to improve RO membrane performance was employed for enhancing water flux of thin film composite forward osmosis membrane. Home-made polysulfide-based forward osmosis membrane was prepared and nitric acid, sulfuric acid, ethanol, 2-propanol were employed as post-treatment solutions. After a short-term treatment, all the membrane samples manifested water flux enhancement compared with their untreated counterparts. Over 50% increase of water flux had been obtained by ethanol solution treatment. The swelling, changes of hydrophobicity and solvency in both active layer and substrate were verified as the major causes for the enhancement of the water flux. It is noted that the treatment time and solution concentration should be controlled to get both appropriate water flux and reverse salt flux. The results obtained in this study will be useful for further FO membrane development and application.

  4. Chemical etching of stainless steel 301 for improving performance of electrochemical capacitors in aqueous electrolyte

    Science.gov (United States)

    Jeżowski, P.; Nowicki, M.; Grzeszkowiak, M.; Czajka, R.; Béguin, F.

    2015-04-01

    The main purpose of the study was to increase the surface roughness of stainless steel 301 current collectors by etching, in order to improve the electrochemical performance of electrical double-layer capacitors (EDLC) in 1 mol L-1 lithium sulphate electrolyte. Etching was realized in 1:3:30 (HNO3:HCl:H2O) solution with times varying up to 10 min. For the considered 15 μm thick foil and a mass loss around 0.4 wt.%, pitting was uniform, with diameter of pits ranging from 100 to 300 nm. Atomic force microscopy (AFM) showed an increase of average surface roughness (Ra) from 5 nm for the as-received stainless steel foil to 24 nm for the pitted material. Electrochemical impedance spectroscopy realized on EDLCs with coated electrodes either on as-received or pitted foil in 1 mol L-1 Li2SO4 gave equivalent distributed resistance (EDR) of 8 Ω and 2 Ω, respectively, demonstrating a substantial improvement of collector/electrode interface after pitting. Correlatively, the EDLCs with pitted collector displayed a better charge propagation and low ohmic losses even at relatively high current of 20 A g-1. Hence, chemical pitting of stainless steel current collectors is an appropriate method for optimising the performance of EDLCs in neutral aqueous electrolyte.

  5. [Life quality parameters in prenosologic evaluation of health state in residents of protective measures area near objects of storage and destruction of chemical weapons].

    Science.gov (United States)

    Filippov, V L; Nechaeva, E N

    2014-01-01

    The article presents results of life quality assessment and subjective evaluation data on health state, used for prenosologic evaluation of health state in residents of protective measures area near objects of storage and destruction of chemical weapons. Considering specific features of residence near potentially dangerous objects, the authors conducted qualitative evaluation of satisfaction with various life facets, with taking into account the objects specificity, established correlation between life quality and self-evaluation of health with factors influencing public health state.

  6. A preliminary examination of neurocognitive performance and symptoms following a bout of soccer heading in athletes wearing protective soccer headbands.

    Science.gov (United States)

    Elbin, R J; Beatty, Amanda; Covassin, Tracey; Schatz, Philip; Hydeman, Ana; Kontos, Anthony P

    2015-01-01

    This study compared changes in neurocognitive performance and symptom reports following an acute bout of soccer heading among athletes with and without protective soccer headgear. A total of 25 participants headed a soccer ball 15 times over a 15-minute period, using a proper linear heading technique. Participants in the experimental group completed the heading exercise while wearing a protective soccer headband and controls performed the heading exercise without wearing the soccer headband. Neurocognitive performance and symptom reports were assessed before and after the acute bout of heading. Participants wearing the headband showed significant decreases on verbal memory (p = 0.02) compared with the no headband group, while the no headband group demonstrated significantly faster reaction time (p = 0.03) than the headband group following the heading exercise. These findings suggest that protective soccer headgear likely does not mitigate the subtle neurocognitive effects of acute soccer heading.

  7. Enhanced photocathodic protection performance of Ag/graphene/TiO2 composite for 304SS under visible light

    Science.gov (United States)

    Li, Hong; Wang, Xiutong; Wei, Qinyi; Liu, Xueqing; Qian, Zhouhai; Hou, Baorong

    2017-06-01

    Ag and graphene co-sensitized TiO2 composites were successfully fabricated and used as photoanodes for photogenerated cathodic protection of 304 stainless steel (304SS) under visible light. Graphene films was firstly deposited onto the TiO2 nanotube (NT) films via cyclic voltammetric electrodeposition. Ag/graphene/TiO2 films were then fabricated via dipping and photoreduction method. The morphology, composition and optical response of the Ag/graphene/TiO2 NT composites were characterized by scanning electron microscopy, x-ray diffraction, x-ray photoelectron spectroscopy, UV-vis diffusion reflectance spectroscopy, respectively. The photocathodic protection performance of the Ag/graphene/TiO2 composites were systematically studied through open-circuit potential and potentiodynamic polarization measurements in 3.5 wt% NaCl solution under visible light (λ > 400 nm). The composites exhibited enhanced photogenerated cathodic protection performance for 304SS under visible light irradiation compared to pure TiO2. Graphene and Ag have a synergistic effect on the enhancement of photocathodic protection performance of TiO2. The composites prepared with 30-cycle graphene film and 15 mM AgNO3 solution showed the optimal corrosion protection performance.

  8. Chemical buffering in natural and engineered barrier systems: Thermodynamic constraints and performance assessment consequences

    Energy Technology Data Exchange (ETDEWEB)

    Arthur, R.C.; Wei Zhou [Monitor Scientific, LLC, Denver, CO (United States)

    2000-12-01

    Thermodynamic and kinetic constraints on the chemical buffering properties of natural and engineered-barrier systems are derived in this study from theoretical descriptions, incorporated in the reaction-path model, of reversible and irreversible mass transfer in multicomponent, multiphase systems. The buffering properties of such systems are conditional properties because they refer to a specific aqueous species in a system that is open with respect to a specific reactant. The solution to a mathematical statement of this concept requires evaluation of the dependence of the activity of the buffered species on incremental changes in the overall reaction-progress variable. This dependence can be represented by a truncated Taylor's series expansion, where the values of associated derivatives are calculated using finite-difference techniques and mass-balance, charge-balance and mass-action constraints. Kinetic constraints on buffering behavior can also be described if the relation between reactant flux and reaction rate is well defined. This relation is explicit for the important case of advective groundwater flow and water-rock interaction. We apply the theoretical basis of the chemical buffering concept to processes that could affect the performance of a deep geologic repository for nuclear waste. Specifically, we focus on the likelihood that an inverse relation must exist between the buffer intensity and the migration velocity of reaction fronts in systems involving advective or diffusive mass transport. A quantitative understanding of this relation would provide the basis for evaluating the potential role of chemical buffering in achieving the isolation and retardation functions, of the EBS and geosphere in a KBS-3 repository. Our preliminary evaluation of this role considers the effects of chemical buffering on the propagation velocity of a pH front in both the near- and far field. We use a geochemical modeling technique compatible with the reaction-path model

  9. Cost and Performance Assessment of In-situ Chemical Oxidation for Intermittent and Continuous Oxidant Injection

    Science.gov (United States)

    Kim, U.; Parker, J.; Borden, R. C.

    2015-12-01

    In situ chemical oxidation (ISCO) is a popular remediation technology that involves injection of chemical oxidant into groundwater to destroy dissolved and non-aqueous liquid phase contaminants. Depending on site conditions, oxidant can be injected into the contaminated subsurface periodically (intermittently) or continuously. A common approach is to intermittently inject oxidant into a network of wells over a period long enough to emplace oxidant over a target treatment volume (referred to ISCO-int). The injection phase is followed by a passive phase when the oxidant is allowed to react with contaminants and natural oxygen demand (NOD) and to migrate under natural hydraulic gradients. This process may be repeated multiple times until termination criteria are met. Recently, some practitioners have adopted an alternative approach in which oxidant is injected continuously with extraction wells recovering unreacted oxidant to recycle with additional makeup oxidant to maintain its constant concentration (referred to ISCO-cont). Each method has certain advantages and disadvantages. This study numerically evaluates those two ISCO practices in terms of remediation costs and performance based on multiple equi-probable parameter sets. Stochastic cost optimization toolbox (SCOToolkit) is used for this purpose. SCOToolkit is an integrated semi-analytical model for contaminant transport and remediation (e.g., thermal source treatment, ISCO, electron donor injections, permeable reactive barriers) enabling inverse solution and Monte Carlo simulations. Four different aquifer settings, slow and fast Darcy velocities combined with low and high NOD conditions, are used for the evaluation. Preliminary results showed that ISCO-cont is effective for a full scale application without large investment while ISCO-int is more efficient to utilize oxidant in well-characterized sites. Pros and cons of each approach are discussed for the practical use of ISCO for various site conditions.

  10. Thermo-hydro-chemical performance assessment of CO2 storage in saline aquifer

    International Nuclear Information System (INIS)

    Le Gallo, Y.; Trenty, L.; Michel, A.

    2007-01-01

    Research and development methodologies for the storage of CO 2 in geological formation are in developing over the last 10 years. In this context, numerical simulators are the practical tools to understand the physical processes involved by acid gas injection and evaluate the long term stability of the storage. CO 2 storage models can be seen as a mix between two types of models: a reservoir model coupling multiphase flow in porous media with local phase equilibrium and a hydrogeochemical model coupling transport in aqueous phase with local chemical equilibrium and kinetic reaction laws. A 3D-multiphase model, COORES, was built to assess the influence of different driving forces both hydrodynamic and geomechanics as well as geochemical on the CO 2 plume behavior during injection and storage (1000 years). Different coupling strategies were used to model these phenomena: - pressure, temperature and diffusion are solved implicitly for better numerical stability; - geochemical reactions involve heterogeneous kinetically-controlled reactions between the host rock and the CO 2 -rich aqueous phase which imply an implicit coupling with fluid flow; From the assumed initial mineral composition (6 minerals), aqueous species (10 chemical elements and 37 aqueous species), the geochemical alteration of the host rocks (sand and shale) is directly linked with the CO 2 plume evolution. A performance assessment using an experimental design approach is used to quantify the different driving forces and parameter influences. In the case of CO 2 injection in a saline quartz rich aquifer used to illustrate the model capabilities, the geochemical changes of the host rock have a small influence on the CO 2 distribution at the end of storage life (here 1000 years) compared to the other hydrodynamic mechanisms: free CO 2 (gas or supercritical), or trapped (capillary and in-solution). (authors)

  11. Performance of the Protection System for Superconducting Circuits during LHC Operation

    OpenAIRE

    Denz, R; Charifoulline, Z; Dahlerup-Petersen, K; Schmidt, R; Siemko, A; Steckert, J

    2011-01-01

    The protection system for superconducting magnets and bus-bars is an essential part of the LHC machine protection and ensures the integrity of substantial elements of the accelerator. Due to the large amount of hardwired and software interlock channels the dependability of the system is a critical parameter for the successful operation of the LHC.

  12. Using scoring methods to assess the performance of CBRN personal protective systems in different scenarios.

    NARCIS (Netherlands)

    Houwelingen, T.; Kistemaker, L.A.; Kant, S. de; Hartog, E.A. den

    2010-01-01

    The past decades show an increasing variety in the design and application of personal protective equipment, PPE. Even within the PPE aimed at CBRN protection the future user can choose from a bewildering amount of producers and models. To make his predicament even worse he also has to deal with a

  13. Performance Evaluation of Fusing Protected Fingerprint Minutiae Templates on the Decision Level

    NARCIS (Netherlands)

    Yang, Bian; Busch, C.; Groot, K. de; Xu, H.; Veldhuis, Raymond N.J.

    In a biometric authentication system using protected templates, a pseudonymous identifier is the part of a protected template that can be directly compared. Each compared pair of pseudonymous identifiers results in a decision testing whether both identifiers are derived from the same biometric

  14. Performance evaluation of fusing protected fingerprint minutiae templates on the decision level

    NARCIS (Netherlands)

    Yang, B.; Groot, K.T.J. de; Christoph Busch; Veldhuis, R.N.J.; Xu, H.

    2013-01-01

    In a biometric authentication system using protected templates, a pseudonymous identifier is the part of a protected template that can be directly compared. Each compared pair of pseudonymous identifiersresults in a decision testing whether both identifiers are derived from the same biometric

  15. Enhanced performance of electrostatic precipitators through chemical modification of particle resistivity and cohesion

    Energy Technology Data Exchange (ETDEWEB)

    Durham, M.D.; Baldrey, K.E.; Bustard, C.J. [ADA Technologies, Inc., Englewood, CO (United States)

    1995-11-01

    Control of fine particles, including particulate air toxics, from utility boilers is required near-term by state and federal air regulations. Electrostatic precipitators (ESP) serve as the primary air pollution control device for the majority of coal-fired utility boilers in the Eastern and Midwestern united States. Cost-effective retrofit technologies for fine particle control, including flue gas conditioning, are needed for the large base of existing ESPs. Flue has conditioning is an attractive option because it requires minimal structural changes and lower capital costs. For flue gas conditioning to be effective for fine particle control, cohesive and particle agglomerating agents are needed to reduce reentrainment losses, since a large percentage of particulate emissions from well-performing ESPs are due to erosion, rapping, and non-rapping reentrainment. A related and somewhat ironic development is that emissions reductions of SO{sub 2} from utility boilers, as required by the Title IV acid rain program of the 1990 Clean Air Act amendments, has the potential to substantially increase particulate air toxics from existing ESPs. The switch to low-sulfur coals as an SO{sub 2} control strategy by many utilities has exacerbated ESP performance problems associated with high resistivity flyash. The use of flue gas conditioning has increased in the past several years to maintain adequate performance in ESPs which were not designed for high resistivity ash. However, commercially available flue gas conditioning systems, including NH{sub 3}/SO{sub 3} dual gas conditioning systems, have problems and inherent drawbacks which create a need for alternative conditioning agents. in particular, NH{sub 3}/SO{sub 3} systems can create odor and ash disposal problems due to ammonia outgassing. In addition, there are concerns over chemical handling safety and the potential for accidental releases.

  16. Performance/design criteria review advanced worker protection systems. Topical report

    International Nuclear Information System (INIS)

    1996-08-01

    The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D ampersand D) obligations at its numerous sites. Several technologies are being investigated which can potentially reduce D ampersand D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D ampersand D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This document describes an Advanced Worker Protection System (AWPS). The AWPS is built around a life support backpack that uses liquid air to provide cooling as well as breathing gas to the worker. The backpack will be combined with a variety of articles of protective clothing and support equipment

  17. Performance/design criteria review advanced worker protection systems. Topical report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D&D) obligations at its numerous sites. Several technologies are being investigated which can potentially reduce D&D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D&D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This document describes an Advanced Worker Protection System (AWPS). The AWPS is built around a life support backpack that uses liquid air to provide cooling as well as breathing gas to the worker. The backpack will be combined with a variety of articles of protective clothing and support equipment.

  18. The legal changes regarding chemical protection used by amateurs, available active substances and the expected impact on the development of pest resistance in Poland

    Directory of Open Access Journals (Sweden)

    Ewa Matyjaszczyk

    2015-06-01

    Full Text Available Beginning from June 2015, non-professionals will be allowed to only buy and use plant protection products bearing information on the label that they are intended for use by non-professionals. Based on the current register and derogations, the following products will be available for use by amateurs: 21 fungicides, 30 insecticides and 15 herbicides with respectively 20, 14 and 9 different active substances. Over a third of the mentioned active substances of fungicides and insecticides are classified as “high risk” in terms of probability of pest resistance development. For numerous uses only a single product is available. The area of home gardens in Poland amounts to 53.5 thousand hectares. Sales of plant protection products for use by amateurs is about 7% of the market value. The very limited availability of chemical plant protection products for non-professionals can be a serious problem if seen from the perspective of pest resistance development and dissemination. Resistant pests may also affect farms with commercial production. Poland is an important producer of a variety of fruits, vegetables and ornamental plants with a very limited availability of chemical protection. Resistance development can further reduce the practical means of pest control and became a serious economic problem.

  19. High-performance metabolic profiling of plasma from seven mammalian species for simultaneous environmental chemical surveillance and bioeffect monitoring

    OpenAIRE

    Park, Youngja H.; Lee, Kichun; Soltow, Quinlyn A.; Strobel, Frederick H.; Brigham, Kenneth L.; Parker, Richard E.; Wilson, Mark E.; Sutliff, Roy L.; Mansfield, Keith G.; Wachtman, Lynn M.; Ziegler, Thomas R.; Jones, Dean P.

    2012-01-01

    High-performance metabolic profiling (HPMP) by Fourier-transform mass spectrometry coupled to liquid chromatography gives relative quantification of thousands of chemicals in biologic samples but has had little development for use in toxicology research. In principle, the approach could be useful to detect complex metabolic response patterns to toxicologic exposures and to detect unusual abundances or patterns of potentially toxic chemicals. As an initial study to develop these possible uses,...

  20. High-performance metabolic profiling of plasma from seven mammalian species for simultaneous environmental chemical surveillance and bioeffect monitoring.

    Science.gov (United States)

    Park, Youngja H; Lee, Kichun; Soltow, Quinlyn A; Strobel, Frederick H; Brigham, Kenneth L; Parker, Richard E; Wilson, Mark E; Sutliff, Roy L; Mansfield, Keith G; Wachtman, Lynn M; Ziegler, Thomas R; Jones, Dean P

    2012-05-16

    High-performance metabolic profiling (HPMP) by Fourier-transform mass spectrometry coupled to liquid chromatography gives relative quantification of thousands of chemicals in biologic samples but has had little development for use in toxicology research. In principle, the approach could be useful to detect complex metabolic response patterns to toxicologic exposures and to detect unusual abundances or patterns of potentially toxic chemicals. As an initial study to develop these possible uses, we applied HPMP and bioinformatics analysis to plasma of humans, rhesus macaques, marmosets, pigs, sheep, rats and mice to determine: (1) whether more chemicals are detected in humans living in a less controlled environment than captive species and (2) whether a subset of plasma chemicals with similar inter-species and intra-species variation could be identified for use in comparative toxicology. Results show that the number of chemicals detected was similar in humans (3221) and other species (range 2537-3373). Metabolite patterns were most similar within species and separated samples according to family and order. A total of 1485 chemicals were common to all species; 37% of these matched chemicals in human metabolomic databases and included chemicals in 137 out of 146 human metabolic pathways. Probability-based modularity clustering separated 644 chemicals, including many endogenous metabolites, with inter-species variation similar to intra-species variation. The remaining chemicals had greater inter-species variation and included environmental chemicals as well as GSH and methionine. Together, the data suggest that HPMP provides a platform that can be useful within human populations and controlled animal studies to simultaneously evaluate environmental exposures and biological responses to such exposures. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  1. Describing the chemical singularity of the Spanish protected designations of origin for virgin olive oils in relation to oils from neighbouring areas

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Gonzalez, D. L.; Tena, N.; Aparicio, R.

    2012-11-01

    The protected designations of origin (PDOs) have proven to be a successful regulatory framework to protect singular virgin olive oils that have distinctive properties. However, sometimes the registration of new PDOs and the demarcation of the geographical areas associated to them are based on administrative issues rather than objective chemical data. In this work, the chemical compositions of fatty acids, hydrocarbons, alcohols, sterols and methyl sterols have been used to prove the differences between a PDO virgin olive oil and the oils produced in the surrounding areas. Three cases were studied (PDO Estepa, PDO Montoro-Adamuz, and Campina de Jaen) which actually mean three different situations that combine variations in cultivar and pedoclimatic characteristics. The chemical compounds that showed a better ability to classify samples were selected by the Brown- Forsythe test, a particular modification of ANOVA, and this ability was later visualized in a principal component analysis. The oils from PDOs Estepa and Montoro-Adamuz showed clear differences in their chemical compositions, while the oils from Campina de Jaen formed a group of samples which greatly overlapped with the oils from surrounding areas, probably due to the lack of variation in cultivar (Picual) throughout the province of Jaen. (Author) 32 refs.

  2. Preparedness activities regarding the protection of public health in case of a major oil or chemical spill on the St-Lawrence River

    International Nuclear Information System (INIS)

    Guerrier, P.; Manon, P.

    1996-01-01

    A project was initiated to protect the health of people living in the St-Lawrence basin from contaminants associated with an oil or chemical spill. Between 1980 and 1990, more than 240 chemical spills and 300 oil spills were recorded in the region which has prompted concerns regarding the possible contamination of drinking water sources. 45% of Quebec's population relies on the St-Lawrence River as a source of drinking water. Thus far, the project has identified the major chemical and oil products transported on the St-Lawrence River, and the main health risks associated with these products. Computerized dispersion models which can determine the migration of the contaminants in water, are available. Simulation exercises have been carried out to train personnel in the event of an actual spill. 1 ref

  3. Hazardous Chemicals

    Centers for Disease Control (CDC) Podcasts

    Chemicals are a part of our daily lives, providing many products and modern conveniences. With more than three decades of experience, The Centers for Disease Control and Prevention (CDC) has been in the forefront of efforts to protect and assess people's exposure to environmental and hazardous chemicals. This report provides information about hazardous chemicals and useful tips on how to protect you and your family from harmful exposure.

  4. Test Operations Procedure (TOP) 10-2-022A Chemical Vapor and Aerosol System-Level Testing of Chemical/Biological Protective Suits

    Science.gov (United States)

    2013-12-16

    data, QA/quality control (QC) plans]. 3.1.2 Familiarization. a. Potential problem areas will be identified by reviewing previous records and results...also wear specified footwear , gloves, protective mask, and hood. e. Test operators will assist the TPs in obtaining correct closure of the suit at...Vernon Hills, Illinois); and Pureline II® (Dixon Industries , Charlotte, North Carolina). (4) The pressure inside each RTM while drawing air must not

  5. Thermal Protection Performance of Carbon Aerogels Filled with Magnesium Chloride Hexahydrate as a Phase Change Material

    Directory of Open Access Journals (Sweden)

    Ali Kazemi

    2014-02-01

    Full Text Available Carbon aerogels are comprised of a class of low density open-cell foams with large void space, nanometer pore size and composed of sparsely semi-colloidal nanometer sized particles forming an open porous structure. Phase change materials are those with high heat of fusion that could absorb and release a large amount of energy at the time of phase transition. These materials are mostly used as thermal energy storage materials but in addition they could serve as an obstacle for passage of heat during phase changes and this has led to their use in thermal protection systems. In this study, the effect of magnesium chloride hexahydrate, as a phase change material (melting point 115°C, on thermal properties of carbon aerogels is investigated. Thermal performance tests are designed and used for comparing the temperature-time behavior of the samples. DSC is applied to obtain the latent heat of melting of the phase change materials and the SEM tests are used to analyze the microstructure and morphology of carbon aerogels. The results show that the low percentage of phase change materials in carbon aerogels does not have any significant positive effect on carbon aerogels thermal properties. However, these properties are improved by increasing the percentage of phase change materials. With high percentage of phase change materials, a sample surface at 300°C would display an opposite surface with a significant drop in temperature increases, while at 115-200°C, with carbon aerogels, having no phase change materials, there is a severe reduction in the rate of temperature increase of the sample.

  6. A High Performance Chemical Simulation Preprocessor and Source Code Generator, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Numerical simulations of chemical kinetics are a critical component of aerospace research, Earth systems research, and energy research. These simulations enable a...

  7. Effects of chemical sludge disintegration on the performances of wastewater treatment by membrane bioreactor.

    Science.gov (United States)

    Oh, Young-Khee; Lee, Ki-Ryong; Ko, Kwang-Baik; Yeom, Ick-Tae

    2007-06-01

    A new wastewater treatment process combining a membrane bioreactor (MBR) with chemical sludge disintegration was tested in bench scale experiments. In particular, the effects of the disintegration treatment on the excess sludge production in MBR were investigated. Two MBRs were operated. In one reactor, a part of the mixed liquor was treated with NaOH and ozone gas consecutively and was returned to the bioreactor. The flow rate of the sludge disintegration stream was 1.5% of the influent flow rate. During the 200 days of operation, the MLSS level in the bioreactor with the disintegration treatment was maintained relatively constant at the range of 10,000-11,000 mg/L while it increased steadily up to 25,000 mg/L in the absence of the treatment. In the MBR with the sludge disintegration, relatively constant transmembrane pressures (TMPs) could be maintained for more than 6 months while the MBR without disintegration showed an abrupt increase of TMP in the later phase of the operation. In conclusion, a complete control of excess sludge production in the membrane-coupled bioreactor was possible without significant deterioration of the treated water quality and membrane performances.

  8. Evaluating the performance of low cost chemical sensors for air pollution research.

    Science.gov (United States)

    Lewis, Alastair C; Lee, James D; Edwards, Peter M; Shaw, Marvin D; Evans, Mat J; Moller, Sarah J; Smith, Katie R; Buckley, Jack W; Ellis, Matthew; Gillot, Stefan R; White, Andrew

    2016-07-18

    Low cost pollution sensors have been widely publicized, in principle offering increased information on the distribution of air pollution and a democratization of air quality measurements to amateur users. We report a laboratory study of commonly-used electrochemical sensors and quantify a number of cross-interferences with other atmospheric chemicals, some of which become significant at typical suburban air pollution concentrations. We highlight that artefact signals from co-sampled pollutants such as CO2 can be greater than the electrochemical sensor signal generated by the measurand. We subsequently tested in ambient air, over a period of three weeks, twenty identical commercial sensor packages alongside standard measurements and report on the degree of agreement between references and sensors. We then explore potential experimental approaches to improve sensor performance, enhancing outputs from qualitative to quantitative, focusing on low cost VOC photoionization sensors. Careful signal handling, for example, was seen to improve limits of detection by one order of magnitude. The quantity, magnitude and complexity of analytical interferences that must be characterised to convert a signal into a quantitative observation, with known uncertainties, make standard individual parameter regression inappropriate. We show that one potential solution to this problem is the application of supervised machine learning approaches such as boosted regression trees and Gaussian processes emulation.

  9. Off-design performance of a chemical looping combustion (CLC) combined cycle: effects of ambient temperature

    Science.gov (United States)

    Chi, Jinling; Wang, Bo; Zhang, Shijie; Xiao, Yunhan

    2010-02-01

    The present work investigates the influence of ambient temperature on the steady-state off-design thermodynamic performance of a chemical looping combustion (CLC) combined cycle. A sensitivity analysis of the CLC reactor system was conducted, which shows that the parameters that influence the temperatures of the CLC reactors most are the flow rate and temperature of air entering the air reactor. For the ambient temperature variation, three off-design control strategies have been assumed and compared: 1) without any Inlet Guide Vane (IGV) control, 2) IGV control to maintain air reactor temperature and 3) IGV control to maintain constant fuel reactor temperature, aside from fuel flow rate adjusting. Results indicate that, compared with the conventional combined cycle, due to the requirement of pressure balance at outlet of the two CLC reactors, CLC combined cycle shows completely different off-design thermodynamic characteristics regardless of the control strategy adopted. For the first control strategy, temperatures of the two CLC reactors both rise obviously as ambient temperature increases. IGV control adopted by the second and the third strategy has the effect to maintain one of the two reactors' temperatures at design condition when ambient temperature is above design point. Compare with the second strategy, the third would induce more severe decrease of efficiency and output power of the CLC combined cycle.

  10. Physico-chemical properties and performance of high oleic and palm-based shortenings.

    Science.gov (United States)

    Ramli, Muhamad Roddy; Lin, Siew Wai; Yoo, Cheah Kien; Idris, Nor Aini; Sahri, Miskandar Mat

    2008-01-01

    Solid fat from fractionation of palm-based products was converted into cake shortening at different processing conditions. High oleic palm stearin with an oleic content of 48.2 % was obtained from fractionation of high oleic palm oil which was produced locally. Palm product was blended with different soft oils at pre-determined ratio and further fractionated to obtain the solid fractions. These fractions were then converted into cake shortenings named as high oleic, N1 and N2 blends. The physico-chemical properties of the experimental shortenings were compared with those of control shortenings in terms of fatty acid composition (FAC), iodine value (IV), slip melting point (SMP), solid fat content (SFC) and polymorphic forms. Unlike the imported commercial shortenings as reported by other studies and the control, experimental shortenings were trans-free. The SMP and SFC of experimental samples, except for the N2 sample, fell within the ranges of commercial and control shortenings. The IV was higher than those of domestic shortenings but lower when compared to imported and control shortenings. They were also observed to be beta tending even though a mixture of beta and beta' was observed in the samples after 3 months of storage. The shortenings were also used in the making of pound cake and sensory evaluation showed the good performance of high oleic sample as compared to the other shortenings.

  11. Optimizing Performance Parameters of Chemically-Derived Graphene/p-Si Heterojunction Solar Cell.

    Science.gov (United States)

    Batra, Kamal; Nayak, Sasmita; Behura, Sanjay K; Jani, Omkar

    2015-07-01

    Chemically-derived graphene have been synthesized by modified Hummers method and reduced using sodium borohydride. To explore the potential for photovoltaic applications, graphene/p-silicon (Si) heterojunction devices were fabricated using a simple and cost effective technique called spin coating. The SEM analysis shows the formation of graphene oxide (GO) flakes which become smooth after reduction. The absence of oxygen containing functional groups, as observed in FT-IR spectra, reveals the reduction of GO, i.e., reduced graphene oxide (rGO). It was further confirmed by Raman analysis, which shows slight reduction in G-band intensity with respect to D-band. Hall effect measurement confirmed n-type nature of rGO. Therefore, an effort has been made to simu- late rGO/p-Si heterojunction device by using the one-dimensional solar cell capacitance software, considering the experimentally derived parameters. The detail analysis of the effects of Si thickness, graphene thickness and temperature on the performance of the device has been presented.

  12. Broiler performance fed jatropha curcas seed meal detoxified by fermentation, physic and chemical treatments

    Directory of Open Access Journals (Sweden)

    Elizabeth Wina

    2010-10-01

    Full Text Available Utilization of jatropha seed meal as a feed ingredient is limited by the presence of several anti nutritive and toxic compounds in the seed meal. The aim of this research is to evaluate feeding of jatropha seed meal detoxified using fermentation by two fungi and rumen microbes (as biological detoxification and using a combination of chemical and physical treatments on broiler performance. One hundred seventy five chicks (7 days old were used and were divided into 5 treatments in 7 replications and each replication in one cage consisted of 5 chicks. R1 was control feed (K without jatropha seed meal., 2 R2 was feed with 4% of Jatropha seed meal fermented by Neurosphora sitophila (FNS, R3 was feed with 4% of Jatropha seed meal fermented by Aspergillus oryzae (FAS, R4 was feed with 4% of Jatropha seed meal fermented by rumen microbes and R5 with 4% of Jatropha seed meal treated by autoclaved, refluxed by hexane and soaked in methanol (OEHM. Treated feed was given for 14 days at the end of the feeding treatment, two chickens from each replication were slaughtered and organ weights were recorded. Body weight of chicken and feed conversion ratio were calculated. The rest of the chicken was fed commercial feed for the next 7 days (recovery periode. Chicken mortality was almost 0% but 1 chicken from FAS treatment died at the recovery period. Feed consumption was lower at fermented jatropha seed meal than control (K or OEHM, resulted in lower body weight of chicken. The abdomen fat weight and organ weights especially pancreas or spleen resulted from treatment with jatropha were much lower than that of K. In the recovery period, body weight of chicken in the OEHM treatment was almost similar from that of control chicken. In conclusion, biological detoxification on BBJ was able to reduce chicken mortality but could not improve the daily gain higher than control treatment. The best method to detoxify jatropha seed meal was the combination of physical and

  13. Learnings from LCA-based methods: should chemicals in food packaging be a priority focus to protect human health?

    DEFF Research Database (Denmark)

    Ernstoff, Alexi; Stylianou, Katerina S.; Fantke, Peter

    2017-01-01

    Given the scale and variety of human health damage (HHD) caused by food systems, prioritization methods are urgently needed. In this study HHD is estimated for case studies on red meat and sugary sweetened beverages (SSB) packaged in high-impact polystyrene (HIPS) due to various relevant health...... impacts. Specifically, we aim to asses if chemicals in food packaging are important to HHD in a life cycle context. The functional unit is "daily consumption of a packaged food per person in the United States." Method developments focus on human toxicity characterization of chemicals migrating from...... packaging into food. Chemicals and their concentrations in HIPS were identified from regulatory lists. A new high-throughput model estimated migration into food, depending on properties of chemicals, packaging, food, and scenario, and HHD was extrapolated following LCA characterization methods. An LCA...

  14. Chemical vapour generation of silver: reduced palladium as permanent reaction modifier for enhanced performance

    Czech Academy of Sciences Publication Activity Database

    Matoušek, Tomáš; Sturgeon, R. E.

    2004-01-01

    Roč. 19, č. 8 (2004), s. 1014-1017 ISSN 0267-9477 R&D Projects: GA ČR GA203/01/0453 Institutional research plan: CEZ:AV0Z4031919 Keywords : chemical vapour generation * chemical modification * silver Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 3.926, year: 2004

  15. Performance and Meat Quality of Thin Tailed Sheep in Supplementary Feeding Lemuru Fish Oil Protected By Saponification with Different NaOH Concentration

    Directory of Open Access Journals (Sweden)

    Agustinah Setyaningrum

    2015-09-01

    Full Text Available This study was aimed to obtain oil and the exact saponification with different NaOH concentration to protect unsaturated fats, which does can result in good production performance and lamb meat quality with low saturated fatty acid. Stage one studied the performance of sheep production on supplementing lemuru fish oil (LFO protected with different saponification optimization. Twenty lambs aged 5-6 months early weighing 8-14 kg were divided into 4 treatments, namely P0 basal feed (50% elephant grass + 50% concentrate, P1 (basal feed + soap LFO NaOH 10%, P2 (basal feed + soap LFO NaOH 20% and P3 (basal feed + soap LFO NaOH 30% with completely randomized design and 5 replication for performance and 3 replication for meat quality. The results showed that the treatment effect was not significant (P>0.05 on the consumption of dry matter (DM, crude protein (CP, ether extract (EE, total digestible nutrien (TDN, daily gain and blood cholesterol. P2 yield the highest daily gain 130.95 ± 19.29 g/head/day of cholesterol at the same time low of 58.67 mg/dl. Stage two studied the criteria of lamb carcass and meat quality in supplementary feeding LFO protected with different saponification optimization. Twelve sheeps were slaughtered for P0, P1, P2 and P3. The results showed that the treatment effect was not significant (P> 0.05 to slaughter weight, carcass weight and carcass percentage, the physical quality of meat (pH, water holding capacity, cooking losses and tenderness, and chemical quality of the meat (DM levels, CP , EE, saturated fatty acids and unsaturated fatty acids except in EPA and DHA increased very significantly (P<0.01. Conclusively, giving soap LFO with different optimization did not significantly affect the appearance and quality of sheep meat production, except in EPA and DHA which were significantly increased

  16. Information performances and illative sequences: Sequential organization of explanations of chemical phase equilibrium

    Science.gov (United States)

    Brown, Nathaniel James Swanton

    While there is consensus that conceptual change is surprisingly difficult, many competing theories of conceptual change co-exist in the literature. This dissertation argues that this discord is partly the result of an inadequate account of the unwritten rules of human social interaction that underlie the field's preferred methodology---semi-structured interviewing. To better understand the contributions of interaction during explanations, I analyze eight undergraduate general chemistry students as they attempt to explain to various people, for various reasons, why phenomena involving chemical phase equilibrium occur. Using the methods of interaction analysis, I characterize the unwritten, but systematic, rules that these participants follow as they explain. The result is a description of the contributions of interaction to explaining. Each step in each explanation is a jointly performed expression of a subject-predicate relation, an interactive accomplishment I call an information performance (in-form, for short). Unlike clauses, in-forms need not have a coherent grammatical structure. Unlike speaker turns, in-forms have the clear function of expressing information. Unlike both clauses and speaker turns, in-forms are a co-construction, jointly performed by both the primary speaker and the other interlocutor. The other interlocutor strongly affects the form and content of each explanation by giving or withholding feedback at the end of each in-form, moments I call feedback-relevant places. While in-forms are the bricks out of which the explanation is constructed, they are secured by a series of inferential links I call an illative sequence. Illative sequences are forward-searching, starting with a remembered fact or observation and following a chain of inferences in the hope it leads to the target phenomenon. The participants treat an explanation as a success if the illative sequence generates an in-form that describes the phenomenon. If the illative sequence does

  17. Protection of color and chemical degradation of anthocyanin from purple corn (Zea mays L.) by zinc ions and alginate through chemical interaction in a beverage model.

    Science.gov (United States)

    Luna-Vital, Diego; Cortez, Regina; Ongkowijoyo, Paulina; Gonzalez de Mejia, Elvira

    2018-03-01

    Anthocyanin-rich purple corn pericarp water extract (PCW) has the potential to be used as a natural pigment in beverages. However, it has a limited shelf-life in aqueous solutions. The aim was to evaluate the effect of zinc ion (Zn 2+ ) and alginate on color and chemical stability of anthocyanins from colored corn (PCW) in a beverage model for 12weeks. PCW was incorporated to Kool-Aid® Invisible™ along with ZnCl 2 and/or alginate. Individual ANC were quantified through HPLC, and color stability was evaluated through the CIE-L*a*b* color system. Complexation between PCW and Zn/alginate was evaluated with fluorescence spectroscopy. The combination of Zn and alginate was the most effective treatment improving the half-life of total ANC concentration (10.4weeks), cyanidin-3-O-glucoside (7.5weeks) and chroma (18.4weeks), compared to only PCW (6.6, 4.5 and 12.7weeks, respectively). Zn and alginate had bimolecular quenching constants (Zn k q : 3.4×10 11 M -1 S -1 and AA k q : 1.0×10 12 M -1 S -1 ) suggesting that fluorescence quenching was binding rather than collisional. Results suggested that Zn/alginate interacted with ANC from purple corn slowing its chemical degradation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Sacrificial Protective Coating Materials that can be Regenerated In-Situ to Enable High Performance Membranes

    Energy Technology Data Exchange (ETDEWEB)

    Malati, Peter; Ganguli, Rahul; Mehrotra, Vivek

    2018-03-20

    control the deposition time, which allows us to deposit the coating on large-scale membranes. We tuned the coating chemistry by introducing positive or negative charges to reject divalent ions present in weak black liquor permeate. Therefore, our two-stage membrane system effectively separates high molecular weight organics from weak black liquor using ultrafiltration membranes (Stage 1) and low molecular weight organic molecules and divalent salts from weak black liquor permeate using nanofiltration membranes (Stage 2), while the coating maintains the permeate flux by mitigating fouling. Coated polymeric ultrafiltration membranes have exhibited up to two-fold increase in permeate flux due to substantially lower fouling when concentrating weak black liquor at 85 °C. Coated tubular ceramic membranes show no observable fouling over a period of 72 hours, compared to uncoated membranes that exhibit a 20% drop in flux in less than 3 hours. Beyond 20% permeate recovery, however, the fouling rate for coated and uncoated membranes approached -0.4 LMH/h due to cake-layer formation. This fouling has been shown to be reversible only with coated membranes; uncoated membranes undergo irreversible fouling and the flux only recovers after chemical cleaning. Continuous surface renewal has been demonstrated using coated membranes that have been stripped and recoated with no loss in performance. Coated Stage 2 membranes exhibit increased sodium sulfate and sodium hydroxide rejection over uncoated membranes. Membranes that are coated with the negatively and positively charged coating exhibit a 7% and 10% increase in sulfate rejection, respectively, over uncoated membranes. Total organic carbon and sodium sulfate analyses of the final Stage 2 permeate and samples from WestRock pulp washers indicate that the permeate may be introduced to the pulp-washing cycle at the first or second washer closest to the digester. Coated Stage 1 membranes exhibit an average permeate flux of 4.2 LMH/bar when

  19. Biomonitoring of chemicals in biota of two wetland protected areas exposed to different levels of environmental impact: results of the "PREVIENI" project.

    Science.gov (United States)

    Guerranti, Cristiana; Perra, Guido; Alessi, Eva; Baroni, Davide; Caserta, Dante; Caserta, Donatella; De Sanctis, Augusto; Fanello, Emiliano Leonida; La Rocca, Cinzia; Mariottini, Michela; Renzi, Monia; Tait, Sabrina; Zaghi, Carlo; Mantovani, Alberto; Focardi, Silvano Ettore

    2017-08-18

    The PREVIENI project (funded by the Ministry of Environment) investigated the exposure to endocrine disrupters in samples of human population and environmental biota in Italy. The environmental biomonitoring considered two Italian WWF Oasis, with the aim to compare the presence and effects of endocrine disruptors in organisms from two protected natural areas, respectively, upstream and downstream a chemical emission site. Chemical analysis of pollutants' tissue levels was made on tissues from earthworm, barbell, trout, and coot, selected as bioindicator organisms. The contaminants considered were as follows: the perfluorinated compounds perfuoroctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA), polychlorinated biphenyls (PCBs 58 congeners), polybrominated diphenyl ethers (PBDEs, 13 congeners), polycyclic aromatic hydrocarbons (PAHs, 16 compounds), toxic trace elements, the phthalate di-2-ethylexyl phthalate (DEHP) and its primary metabolite, bisphenol A, synthetic musk compounds (musk xylene, musk ketone, tonalide, and galaxolide), and p-nonylphenol. The analyses showed low concentrations of most pollutants in all species from both areas, compared to available literature; noticeable exceptions were the increases of DEHP's primary metabolite, PBDE, PAHs, Hg, and Pb in barbells, and of PCB and Cd in earthworms from the downstream area. The results showed the presence of endocrine disruptors, including those considered as "non-persistent," in bioindicators from protected areas, albeit at low levels. The results provide a contribution to the evaluation of reference values in biota from Mediterranean Europe and support the relevance of monitoring exposure to pollutants, in particular for freshwater environment, also in protected areas.

  20. Performance of Sweet Pepper under Protective Structure in Gazipur of Bangladesh

    Directory of Open Access Journals (Sweden)

    GMA Halim

    2013-08-01

    Full Text Available Evaluation of sweet pepper cultivation under different protective structures was made in two consecutive seasons of 2007-08 and 2008-09 at the experimental field of Horticulture Research Center of BARI, Gazipur. One popular commercial capsicum variety California Wonder was included in the study with four protective structures (low height poly tunnel, polytunnel with side open, poly tunnel with side closed and poly house including control (open field. Protective structures had remarkable and significant influence on plant growth and yield of sweet pepper. The plants grown under protective structures had higher plant height compared to that of plants grown in open field. The highest individual fruit weight (65.2g was recorded form the plants grown under poly house condition while it was the lowest from open field grown plant (3.34 g. More than five fruits were harvested when the plants were grown under poly tunnel (side closed or poly house. The maximum fruit yield per plant (334.0g was recorded from poly house, which was 160.4% higher than that of plants grown under open field condition. The second highest yield was recorded from the plants of poly tunnel (212.5 indicating bright scope for sweet pepper cultivation under protective structures.

  1. Chemical Annealing of Zinc Tetraphenylporphyrin Films: Effects on Film Morphology and Organic Photovoltaic Performance

    KAUST Repository

    Trinh, Cong

    2012-07-10

    We present a chemical annealing process for organic thin films. In this process, a thin film of a molecular material, such as zinc tetraphenylporphyrin (ZnTPP), is exposed to a vapor of nitrogen-based ligand (e.g., pyrazine, pz, and triazine, tz), forming a film composed of the metal-ligand complex. Fast and quantitative formation of the complex leads to marked changes in the morphology and optical properties of the film. X-ray diffraction studies show that the chemical annealing process converts amorphous ZnTPP films to crystalline ZnTPP•ligand films, whose porphryin planes lie nearly parallel to the substrate (average deviation is 8° for the ZnTPP•pz film). Organic solar cells were prepared with ZnTPP donor and C 60 acceptor layers. Devices were prepared with and without chemical annealing of the ZnTPP layer with a pyrazine ligand. The devices with chemically annealed ZnTPP donor layer show an increase in short-circuit current (J SC) and fill factor (FF) relative to analogous unannealed devices, presumably because of enhanced exciton diffusion length and improved charge conductivity. The open circuit voltages (V OC) of the chemically annealed devices are lower than their unannealed counterpart because of enhanced polaron pair recombination at the donor/acceptor heterojunction. A net improvement of 5-20% in efficiency has been achieved, after chemical annealing of ZnTPP films with pyrazine. © 2012 American Chemical Society.

  2. Effects of rumen-protected methionine, lysine, and histidine on lactation performance of dairy cows.

    Science.gov (United States)

    Giallongo, F; Harper, M T; Oh, J; Lopes, J C; Lapierre, H; Patton, R A; Parys, C; Shinzato, I; Hristov, A N

    2016-06-01

    The objective of this study was to evaluate the effects of supplementing a metabolizable protein (MP)-deficient diet with rumen-protected (RP) Met, Lys, and His, individually or combined, on the performance of lactating dairy cows. The experiment was a 9-wk randomized complete block design with 72 Holstein cows. Following a 2-wk covariate period, cows were blocked by days in milk, milk yield, and parity, and randomly assigned to 1 of the following 6 treatments: (1) MP-adequate diet [MPA; +243g/d MP balance, according to the National Research Council (2001) requirements]; (2) MP-deficient diet (MPD; -54g/d MP balance); (3) MPD supplemented with RPMet (MPDM); (4) MPD supplemented with RPLys (MPDL); (5) MPD supplemented with RPHis (MPDH); and (6) MPD supplemented with RPMet, RPLys, and RPHis (MPDMLH). Dry matter intake (DMI), yields of milk and milk components (fat, protein, lactose) and energy-corrected milk (ECM), feed and ECM feed efficiencies, and milk and plasma urea N were decreased by MPD, compared with MPA. Supplementation of the MPD diet with RPLys increased milk protein content and plasma glucose concentration and tended to increase milk urea N. Addition of RPHis tended to increase DMI, increased milk protein concentration, and numerically increased yields of milk fat, protein, and ECM. In addition to the trends for increased DMI and milk fat content, and higher milk protein concentration, supplementation of the 3 RP AA also increased yields of milk fat, protein, and ECM and ECM feed efficiency. Relative to MPA, milk N efficiency tended to be increased by MPD. Concentrations of plasma essential AA (except Met and Thr) were decreased by MPD compared with MPA. Supplementation of RPMet, RPLys, and RPHis increased plasma Met (except for MPDM), Lys, and His concentrations, respectively. Cows fed MPD had lower blood hemoglobin concentration and numerically higher plasma ghrelin than cows fed MPA. Concentration of total saturated fatty acids in milk fat were or

  3. Comparing the Performance of Protected and Unprotected Areas in Conserving Freshwater Fish Abundance and Biodiversity in Lake Tanganyika, Tanzania

    Directory of Open Access Journals (Sweden)

    Emmanuel Andrew Sweke

    2016-01-01

    Full Text Available Marine protected areas have been shown to conserve aquatic resources including fish, but few studies have been conducted of protected areas in freshwater environments. This is particularly true of Lake Tanganyika, Tanzania. To better conserve the lake’s biodiversity, an understanding of the role played by protected areas in conserving fish abundance and diversity is needed. Sampling of fish and environmental parameters was performed within the Mahale Mountains National Park (MMNP and nearby unprotected areas at depths between 5 m and 10 m. Twelve replicates of fish sampling were performed at each site using gillnets set perpendicularly to the shore. Mann-Whitney tests were performed, and the total amount of species turnover was calculated. A total of 518 individual fish from 57 species were recorded in the survey. The fish weight abundance was fivefold greater in the MMNP than in the unprotected areas. Fish abundance and diversity were higher in the MMNP than in the unprotected areas and decreased with distance from it. Our findings confirmed the importance of the protected area in conserving fish resources in Lake Tanganyika. The study provides baseline information for management of the resources and guiding future studies in the lake and other related ecosystems. Management approaches that foster awareness and engage with communities surrounding the MMNP are recommended for successful conservation of the resources in the region.

  4. Development of a test device to characterize thermal protective performance of fabrics against hot steam and thermal radiation

    International Nuclear Information System (INIS)

    Su, Yun; Li, Jun

    2016-01-01

    Steam burns severely threaten the life of firefighters in the course of their fire-ground activities. The aim of this paper was to characterize thermal protective performance of flame-retardant fabrics exposed to hot steam and low-level thermal radiation. An improved testing apparatus based on ASTM F2731-11 was developed in order to simulate the routine fire-ground conditions by controlling steam pressure, flow rate and temperature of steam box. The thermal protective performance of single-layer and multi-layer fabric system with/without an air gap was studied based on the calibrated tester. It was indicated that the new testing apparatus effectively evaluated thermal properties of fabric in hot steam and thermal radiation. Hot steam significantly exacerbated the skin burn injuries while the condensed water on the skin’s surface contributed to cool down the skin tissues during the cooling. Also, the absorbed thermal energy during the exposure and the cooling was mainly determined by the fabric’s configuration, the air gap size, the exposure time and the existence of hot steam. The research provides a effective method to characterize the thermal protection of fabric in complex conditions, which will help in optimization of thermal protection performance of clothing and reduction of steam burn. (paper)

  5. The additivity of radionuclide and chemical risk estimates in performance evaluation of mixed-waste sites

    International Nuclear Information System (INIS)

    Till, J.E.; Meyer, K.R.

    1990-01-01

    Methods for assessing radioactive waste sites that contain chemical constituents are in the formative stages. In evaluating these sites, a key concern will be the hazard to personnel involved in cleanup work and to the general population. This paper focuses on what we have learned from pathway analysis and risk assessment about providing a combined estimate of risk from exposure to both chemicals and radionuclides. Quantitative radiation risk assessment involves a high degree of uncertainty. Chemical risk assessment generally does not provide quantitative results. Thus, it is not currently possible to develop a useful, quantitative combined risk assessment for mixed-waste sites

  6. Atomic Layer Deposition of Chemical Passivation Layers and High Performance Anti-Reflection Coatings on Back-Illuminated Detectors

    Science.gov (United States)

    Hoenk, Michael E. (Inventor); Greer, Frank (Inventor); Nikzad, Shouleh (Inventor)

    2014-01-01

    A back-illuminated silicon photodetector has a layer of Al2O3 deposited on a silicon oxide surface that receives electromagnetic radiation to be detected. The Al2O3 layer has an antireflection coating deposited thereon. The Al2O3 layer provides a chemically resistant separation layer between the silicon oxide surface and the antireflection coating. The Al2O3 layer is thin enough that it is optically innocuous. Under deep ultraviolet radiation, the silicon oxide layer and the antireflection coating do not interact chemically. In one embodiment, the silicon photodetector has a delta-doped layer near (within a few nanometers of) the silicon oxide surface. The Al2O3 layer is expected to provide similar protection for doped layers fabricated using other methods, such as MBE, ion implantation and CVD deposition.

  7. Method for performing diversity and defense-in-depth analyses of reactor protection systems

    International Nuclear Information System (INIS)

    Preckshot, G.G.

    1994-12-01

    The purpose of this NUREG is to describe a method for analyzing computer-based nuclear reactor protection systems that discovers design vulnerabilities to common-mode failure. The potential for common-mode failure has become an important issue as the software content of protection systems has increased. This potential was not present in earlier analog protection systems because it could usually be assumed that common-mode failure, if it did occur, was due to slow processes such as corrosion or premature wear-out. This assumption is no longer true for systems containing software. It is the purpose of the analysis method described here to determine points of a design for which credible common-mode failures are uncompensated either by diversity or defense-in-depth

  8. Corrosion Protection Performance of Polyester-Melamine Coating with Natural Wood Fiber Using EIS Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Shin, PyongHwa; Shon, MinYoung [Pukyong National University, Busan (Korea, Republic of); Jo, DuHwan [POSCO, Gwangyang (Korea, Republic of)

    2016-04-15

    In the present study, polyester-melamine coating systems with natural wood fiber (NWF) were prepared and the effects of NWF on the corrosion protectiveness of the polyester-melamine coating were examined using EIS analysis. From the results, higher average surface roughness was observed with increase of NWF content. Water diffusivity and water uptake into the polyester-melamine coatings with NWF were much higher than that into the pure polyester-melamine coating. The decrease in the impedance modulus |Z| was associated with the localized corrosion on carbon steel, confirming that corrosion protection of the polyester-melamine coatings with NWF well agrees with its water transport behavior.

  9. Synthesis of Ceramic Protective Coatings for Chemical Plant Parts Operated in Hi-temperature and Corrosive/Erosive Environment

    International Nuclear Information System (INIS)

    Son, M. C.; Park, J. R.; Hong, K. T.; Seok, H. K.

    2005-01-01

    Some feasibility studies are conducted to produce an advanced ceramic coating, which reveals superior chemical and mechanical strength, on metal base structure used in chemical plant. This advanced coating on metallic frame can replace ceramic delivery pipe and reaction chamber used in chemical plant, which are operated in hi-temperature and corrosive/erosive environment. An dual spraying is adopted to reduce the residual stress in order to increase the coating thickness and the residual stress is estimated by in-situ manner. Then new methodology is tried to form special coating of yttrium aluminum garnet(YAG), which reveals hi-strength and low-creep rates at hi-temperature, superior anti-corrosion property, hi-stability against Alkali-Vapor corrosion, and so on, on iron base structure. To verify the formation of YAG during thermal spraying, XRD(X ray diffraction) technique was used

  10. Tuning the performance of a natural treatment process using metagenomics for improved trace organic chemical attenuation

    KAUST Repository

    Drewes, Jorg; Li, Dong; Regnery, Julia; Alidina, Mazahirali; Wing, Alexandredavid; Hoppe-Jones, Christiane

    2014-01-01

    removal of trace organic chemicals of emerging concern (CECs). Increasing the humic content of the primary substrate resulted in higher microbial diversity. Lower concentrations and a higher humic content of the primary substrate promoted the attenuation

  11. Chemical performance of multi-environment trials in lens (Lens culinaris M.).

    Science.gov (United States)

    Karadavut, Ufuk; Palta, Cetin

    2010-01-15

    Genotype-environment (GE) interaction has been a major effect to determine stable lens (Lens culinaris (Medik.) Merr.) cultivars for chemical composition in Turkey. Utilization of the lines depends on their agronomic traits and stability of the chemical composition in diverse environments. The objectives of this study were: (i) to evaluate the influence of year and location on the chemical composition of lens genotypes; and (ii) to determine which cultivar is the most stable. Genotypes were evaluated over 3 years (2005, 2006 and 2007) at four locations in Turkey. Effects of year had the largest impact on all protein contents. GE interaction was analyzed by using linear regression techniques. Stability was estimated using the Eberhart and Russell method. 'Kişlik Kirmizi51' was the most stable cultivar for grain yield. The highest protein was obtained from 'Kişlik Kirmizi51' (4.6%) across environments. According to stability analysis, 'Firat 87' had the most stable chemical composition. This genotype had a regression coefficient (b(i) = 1) around unity, and deviations from regression values (delta(ij) = 0) around zero. Chemical composition was affected by year in this study. Temperature might have an effect on protein, oil, carbohydrate, fibre and ash. Firat 87 could be recommended for favourable environments. Copyright (c) 2009 Society of Chemical Industry.

  12. Chemical fingerprint of Ganmaoling granule by double-wavelength ultra high performance liquid chromatography and ultra high performance liquid chromatography with quadrupole time-of-flight mass spectrometry.

    Science.gov (United States)

    Lou, Qiong; Ye, Xiaolan; Zhou, Yingyi; Li, Hua; Song, Fenyun

    2015-06-01

    A method incorporating double-wavelength ultra high performance liquid chromatography with quadrupole time-of-flight mass spectrometry was developed for the investigation of the chemical fingerprint of Ganmaoling granule. The chromatographic separations were performed on an ACQUITY UPLC HSS C18 column (2.1 × 50 mm, 1.8 μm) at 30°C using gradient elution with water/formic acid (1%) and acetonitrile at a flow rate of 0.4 mL/min. A total of 11 chemical constituents of Ganmaoling granule were identified from their molecular weight, UV spectra, tandem mass spectrometry data, and retention behavior by comparing the results with those of the reference standards or literature. And 25 peaks were selected as the common peaks for fingerprint analysis to evaluate the similarities among 25 batches of Ganmaoling granule. The results of principal component analysis and orthogonal projection to latent structures discriminant analysis showed that the important chemical markers that could distinguish the different batches were revealed as 4,5-di-O-caffeoylquinic acid, 3,5-di-O-caffeoylquinic acid, and 4-O-caffeoylquinic acid. This is the first report of the ultra high performance liquid chromatography chemical fingerprint and component identification of Ganmaoling granule, which could lay a foundation for further studies of Ganmaoling granule. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Protective coating as a factor to ensure the strength and hydraulic performance of recoverable pipelines

    Directory of Open Access Journals (Sweden)

    Orlov Vladimir Aleksandrovich

    2015-01-01

    Full Text Available The authors present an analysis of various types of internal protective pipeline coatings to ensure the strength and hydraulic characteristics of a remodeled pipeline and related coating methods for effective trenchless renovation of engineering systems, water supply systems and sanitation. As protective coating the authors considered a round profile tube of a smaller diameter than of the old pipe, close to the old pipe, sprayed lining on the basis of inorganic and inorganic materials. The article analyzes the methods of trenchless renovation for applying protective coatings: routing in the old pipeline of new pipes made of polymeric materials or polymeric sleeves, centrifugal spraying on the inner surface of pipelines’ inorganic and organic protective coatings. Special attention was paid to bag technology, providing the required strength properties at specific values of the modulus of elasticity and a number of external factors such as the depth of the existing pipe, the existence and magnitude of the horizon groundwater over it. Also attention is paid to the application technology of tape coatings ribbed profile on the inner surface of pipelines. This technology has a unique feature, which is the ability of recoverable pipeline functioning during its renovation by winding an endless belt and the formation of a new pipe. The tape coating winding is carried out by different types of spiral winding machines. The thickness of the protective coating layer forming the tube remains minimal. Inorganic cement-sand and organic coatings were considered as alternative options for repair of pipelines, which allow to localize the defects in the form of a fistula, minor cracks and other damages. However it is noted that a cement-sandy covering is inferior to organic, because it does not provide the strength characteristics of the pipeline system. The main advantage of the organic coating is mudding fistula of a large diameter, making a high wear

  14. A standard analysis method (SAM) for the automated analysis of polychlorinated biphenyls (PCBs) in soils using the chemical analysis automation (CAA) paradigm: validation and performance

    International Nuclear Information System (INIS)

    Rzeszutko, C.; Johnson, C.R.; Monagle, M.; Klatt, L.N.

    1997-10-01

    The Chemical Analysis Automation (CAA) program is developing a standardized modular automation strategy for chemical analysis. In this automation concept, analytical chemistry is performed with modular building blocks that correspond to individual elements of the steps in the analytical process. With a standardized set of behaviors and interactions, these blocks can be assembled in a 'plug and play' manner into a complete analysis system. These building blocks, which are referred to as Standard Laboratory Modules (SLM), interface to a host control system that orchestrates the entire analytical process, from sample preparation through data interpretation. The integrated system is called a Standard Analysis Method (SAME). A SAME for the automated determination of Polychlorinated Biphenyls (PCB) in soils, assembled in a mobile laboratory, is undergoing extensive testing and validation. The SAME consists of the following SLMs: a four channel Soxhlet extractor, a High Volume Concentrator, column clean up, a gas chromatograph, a PCB data interpretation module, a robot, and a human- computer interface. The SAME is configured to meet the requirements specified in U.S. Environmental Protection Agency's (EPA) SW-846 Methods 3541/3620A/8082 for the analysis of pcbs in soils. The PCB SAME will be described along with the developmental test plan. Performance data obtained during developmental testing will also be discussed

  15. Physico-chemical protection, rather than biochemical composition, governs the responses of soil organic carbon decomposition to nitrogen addition in a temperate agroecosystem.

    Science.gov (United States)

    Tan, Wenbing; Wang, Guoan; Huang, Caihong; Gao, Rutai; Xi, Beidou; Zhu, Biao

    2017-11-15

    The heterogeneous responses of soil organic carbon (SOC) decomposition in different soil fractions to nitrogen (N) addition remain elusive. In this study, turnover rates of SOC in different aggregate fractions were quantified based on changes in δ 13 C following the conversion of C 3 to C 4 vegetation in a temperate agroecosystem. The turnover of both total organic matter and specific organic compound classes within each aggregate fraction was inhibited by N addition. Moreover, the intensity of inhibition increases with decreasing aggregate size and increasing N addition level, but does not vary among chemical compound classes within each aggregate fraction. Overall, the response of SOC decomposition to N addition is dependent on the physico-chemical protection of SOC by aggregates and minerals, rather than the biochemical composition of organic substrates. The results of this study could help to understand the fate of SOC in the context of increasing N deposition. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Towards protective MOFs: post-synthetic modification of MIL-101 with oxime groups and their interactions with toxic chemicals

    NARCIS (Netherlands)

    Grol, M. van; Gorzkowska-Sobasb, A.A.; Koning, M.C. de

    2017-01-01

    In an attempt to broaden the scope of protective MOFs towards toxic compounds, we decided to introduce a reactive (nucleophilic) functionality in MIL101 by post-synthesis modification 1,2. This functionality would complement already existing adsorptive properties with an ability to capture or

  17. Promoting Barrier Performance and Cathodic Protection of Zinc-Rich Epoxy Primer via Single-Layer Graphene

    Directory of Open Access Journals (Sweden)

    Jingrong Liu

    2018-05-01

    Full Text Available The effect of single-layer graphene sheets (Gr on the corrosion protection of zinc-rich epoxy primers (ZRPs was investigated. Scanning electron microscopy (SEM with an energy dispersive spectrometer (EDS were used to characterize morphology and composition of the coatings after immersion for 25 days. The cross-sectional SEM images and X-ray photoelectron spectroscopy (XPS confirmed that the addition of single-layer graphene facilitated assembling of zinc oxides on the interface between the coating and the steel. The open circuit potential (OCP, electrochemical impedance spectroscopy (EIS measurements revealed that both the cathodic protection and barrier performance of the ZRP were enhanced after addition of 0.6 wt. % Gr (Gr0.6-ZRP. In addition, the cathodic protection property of the Gr0.6-ZRP was characterized quantitatively by localized electrochemical impedance spectroscopy (LEIS in the presence of an artificial scratch on the coating. The results demonstrate that moderate amounts of single-layer graphene can significantly improve corrosion resistance of ZRP, due to the barrier protection and cathodic protection effects.

  18. Investigating the effectiveness of many-core network processors for high performance cyber protection systems. Part I, FY2011.

    Energy Technology Data Exchange (ETDEWEB)

    Wheeler, Kyle Bruce; Naegle, John Hunt; Wright, Brian J.; Benner, Robert E., Jr.; Shelburg, Jeffrey Scott; Pearson, David Benjamin; Johnson, Joshua Alan; Onunkwo, Uzoma A.; Zage, David John; Patel, Jay S.

    2011-09-01

    This report documents our first year efforts to address the use of many-core processors for high performance cyber protection. As the demands grow for higher bandwidth (beyond 1 Gbits/sec) on network connections, the need to provide faster and more efficient solution to cyber security grows. Fortunately, in recent years, the development of many-core network processors have seen increased interest. Prior working experiences with many-core processors have led us to investigate its effectiveness for cyber protection tools, with particular emphasis on high performance firewalls. Although advanced algorithms for smarter cyber protection of high-speed network traffic are being developed, these advanced analysis techniques require significantly more computational capabilities than static techniques. Moreover, many locations where cyber protections are deployed have limited power, space and cooling resources. This makes the use of traditionally large computing systems impractical for the front-end systems that process large network streams; hence, the drive for this study which could potentially yield a highly reconfigurable and rapidly scalable solution.

  19. Office of River Protection (ORP) Monthly Performance Report for September 2000

    International Nuclear Information System (INIS)

    WAGNILD, K.J.

    2000-01-01

    CH2M Hill Hanford Group, Inc. (CHG) had an outstanding year. The most significant accomplishments that occurred throughout fiscal year (FY) 2000 include the following: On April 24,2000, DOE ORP received BNFL Inc. B-1 deliverables and CHG completed Phase 1 Part B-2 Readiness-to-Proceed (RTP), to demonstrate the ability to provide waste feed to be treated/stored in a long-term disposal facility. The RTP consisted of key enabling assumptions, critical risks, waste handling actions, financial and schedule risk analysis, staffing plans, a project execution plan, and a resource loaded schedule. The Department determined that the BNFL Inc. proposal was unacceptable in many areas and essentially shifted the financial risk from BNFL Inc. back to the Federal government; thus a key benefit of privatization was lost. On May 8,2000, the Secretary announced that the privatization contract be terminated. In the interim, the Department directed the onsite Tank Farm Contractor, CHG, to continue the design work scope for the Waste Treatment and Immobilization Plant until a new waste treatment contract is awarded. DOE ORP released its request for proposals (RFP) for a new Waste Treatment and Immobilization contractor on August 31,2000 and is on schedule to meet award of the contract by January 15,2000. CHG successfully reached 1,000,000 safe work hours without a lost workday injury or illness on Wednesday, September 23,2000. The record was initiated on May 23,2000 and took 114 days to achieve. All Tri-Party Agreement and Consent Decree milestones scheduled for the fiscal year were completed. Along with meeting all enforceable agreement milestones, nineteen out of twenty Performance Incentives (PIS) were successfully completed. The 20 PIS comprised of 114 specific deliverables, of which 107 were met. In addition to the 20 scheduled PIS, six accelerated activities were completed. Tank 241-SY-101 hydrogen generation was successfully mitigated this fiscal year, including a series of

  20. Effect of feeding rumen-protected methionine on productive and reproductive performance of dairy cows

    Science.gov (United States)

    Toledo, Mateus Z.; Baez, Giovanni M.; Garcia-Guerra, Alvaro; Lobos, Nelson E.; Guenther, Jerry N.; Trevisol, Eduardo; Luchini, Daniel; Shaver, Randy D.

    2017-01-01

    The objectives of this study were to evaluate the effects of daily top-dressing (individually feeding on the top of the total mixed ration) with rumen-protected methionine (RPM) from 30 ± 3 until 126 ± 3 Days in milk on productive and reproductive performance in lactating dairy cows. A total of 309 lactating dairy Holstein cows (138 primiparous and 171 multiparous) were randomly assigned to treatment diets containing either RPM (21.2 g of RPM + 38.8 g of dried distillers grain; 2.34% Methionine [Met] of metabolizable protein [MP]) or Control (CON; 60 g of dried distillers grain; 1.87% Met of MP). Plasma amino acids were evaluated at the time of artificial insemination (AI) and near pregnancy diagnosis. Milk production and milk composition were evaluated monthly. Pregnancy was diagnosed on Day 28 (by Pregnancy-specific protein B [PSPB]), 32, 47, and 61 (by ultrasound) and sizes of embryonic and amniotic vesicle were determined by ultrasound on Day 33 after AI. Feeding RPM increased plasma Met at 6, 9, 12, and 18 hours after top-dressing with a peak at 12 hours (52.4 vs 26.0 μM; P Cows fed RPM had a small increase in milk protein percentage (3.08 vs 3.00%; P = 0.04) with no differences on milk yield and milk protein yield. Additionally, in multiparous cows, RPM feeding increased milk protein (3.03 vs 2.95%; P = 0.05) and fat (3.45 vs 3.14%; P = 0.01) percentages, although no effects were observed in primiparous cows. In multiparous cows fed RPM, pregnancy loss was lower between Days 28 to 61 (19.6 [10/51] vs. 6.1% [3/49]; P = 0.03) or between Days 32 to 61 (8.9 [4/45] vs. 0 [0/0] %; P = 0.03), although, there was no effect of treatment on pregnancy loss in primiparous cows. Consistent with data on pregnancy loss, RPM feeding increased embryonic abdominal diameter (P = 0.01) and volume (P = 0.009) and amniotic vesicle volume (P = 0.04) on Day 33 of pregnancy in multiparous cows but had no effect on embryonic size in primiparous cows. Thus, the increase in plasma

  1. Combination of high-performance refractometry and infrared spectroscopy as a probe for chemically induced gelation and vitrification of epoxies

    International Nuclear Information System (INIS)

    Mueller, U; Philipp, M; Gervais, P-C; Sanctuary, R; Krueger, J K; Possart, W; Wehlack, C; Kieffer, J

    2010-01-01

    A combination of infrared spectroscopy and high-performance refractometry was used to investigate the chemically induced sol-gel and glass transition during the polymerization of epoxies. Representations of the refractive index versus chemical conversion reveal an interesting insight into the optical properties accompanying gelation and vitrification. Whereas the electronic polarizability of the liquid state of small average molecular mass and the glassy state is dominated by the mass density, an unexpected excess polarizability observed during the gelation is attributed to cooperative dipole-dipole interactions.

  2. Combination of high-performance refractometry and infrared spectroscopy as a probe for chemically induced gelation and vitrification of epoxies

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, U; Philipp, M; Gervais, P-C; Sanctuary, R; Krueger, J K [Laboratoire de Physique des Materiaux, Universite du Luxembourg, 162A avenue de la faiencerie, L-1511 Luxembourg (Luxembourg); Possart, W; Wehlack, C [Fachbereich Werkstoffwissenschaften, Universitaet des Saarlandes, D-66123 Saarbruecken (Germany); Kieffer, J, E-mail: ulrich.mueller@uni.l [Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI (United States)

    2010-08-15

    A combination of infrared spectroscopy and high-performance refractometry was used to investigate the chemically induced sol-gel and glass transition during the polymerization of epoxies. Representations of the refractive index versus chemical conversion reveal an interesting insight into the optical properties accompanying gelation and vitrification. Whereas the electronic polarizability of the liquid state of small average molecular mass and the glassy state is dominated by the mass density, an unexpected excess polarizability observed during the gelation is attributed to cooperative dipole-dipole interactions.

  3. Materials and means for protection of personnel performing liquidation of the Chernobyl' NPP acident consequences

    International Nuclear Information System (INIS)

    Pavlenko, Yu.N.; Sysoev, V.N.; Talachev, A.S.; Frid, E.S.

    1992-01-01

    Composite materials (CM) on the basis of lead has been developed. Special polyethylene-polyisobutylene mixture or polyethylene were used as binding materials. This CM was made as plates with film pressed surface. Sheet of CM with 10 mm thickness may attenuate gamma radiation till 10 times. Cast polymer composition based on polyurethane has been developed for containment of the leed sheets. This composition was capable of hadening in operation process and having technical parameters needed for production of workpieces. Sn-50, Ce-58, Gd-64, W-74, Bi-83 were used for low-energy gamma radiation protection. They were introduced as powders of the elements or their mixtures in dissimilar polymer binders. The materials with high protective parameters were worked out. 1 fig

  4. Predictive performance of the human Cell Line Activation Test (h-CLAT) for lipophilic chemicals with high octanol-water partition coefficients.

    Science.gov (United States)

    Takenouchi, Osamu; Miyazawa, Masaaki; Saito, Kazutoshi; Ashikaga, Takao; Sakaguchi, Hitoshi

    2013-01-01

    To meet the urgent need for a reliable alternative test for predicting skin sensitizing potential of many chemicals, we have developed a cell-based in vitro test, human Cell Line Activation Test (h-CLAT). However, the predictive performance for lipophilic chemicals in the h-CLAT still remains relatively unknown. Moreover, it's suggested that low water solubility of chemicals might induce false negative outcomes. Thus, in this study, we tested relatively low water soluble 37 chemicals with log Kow values above and below 3.5 in the h-CLAT. The small-scale assessment resulted in nine false negative outcomes for chemicals with log Kow values greater than 3.5. We then created a dataset of 143 chemicals by combining the existing dataset of 106 chemicals and examined the predictive performance of the h-CLAT for chemicals with a log Kow of less than 3.5; a total of 112 chemicals from the 143 chemicals in the dataset. The sensitivity and overall accuracy for the 143 chemicals were 83% and 80%, respectively. In contrast, sensitivity and overall accuracy for the 112 chemicals with log Kow values below 3.5 improved to 94% and 88%, respectively. These data suggested that the h-CLAT could successfully detect sensitizers with log Kow values up to 3.5. When chemicals with log Kow values greater than 3.5 that were deemed positive by h-CLAT were included with the 112 chemicals, the sensitivity and accuracy in terms of the resulting applicable 128 chemicals out of the 143 chemicals became 95% and 88%, respectively. The use of log Kow values gave the h-CLAT a higher predictive performance. Our results demonstrated that the h-CLAT could predict sensitizing potential of various chemicals, which contain lipophilic chemicals using a large-scale chemical dataset.

  5. Performance of in situ chemical oxidation field demonstrations at DOE sites

    International Nuclear Information System (INIS)

    Cline, S.R.; West, O.R.; Siegrist, R.L.; Holden, W.L.

    1997-01-01

    Researchers at the Oak Ridge National Laboratory (ORNL) have been investigating the use of in situ chemical oxidation to remediate organic contaminants (VOCs, SVOCs, and PCBs) in soils and groundwater at the laboratory and field scales. Field scale design parameters (e.g., oxidant loading rates and oxidant delivery techniques) are often dictated by site conditions (e.g., soil properties and initial contaminant concentrations). Chemical destruction of organic compounds can be accomplished using a variety of oxidants. Recent research has involved field scale in situ chemical oxidation demonstrations using H 2 O 2 and KMnO 4 in conjunction with soil mixing as the oxidant delivery mechanism. A description of some of these fields activities and future field-scale work is presented here

  6. Plasma sprayed manganeseecobalt spinel coatings: Process sensitivity on phase, electrical and protective performance

    Czech Academy of Sciences Publication Activity Database

    Han Jung, S.; Pala, Zdeněk; Sampath, S.

    2016-01-01

    Roč. 304, February (2016), s. 234-243 ISSN 0378-7753 R&D Projects: GA ČR GB14-36566G Institutional support: RVO:61389021 Keywords : Interconnect protection * Cr-poisoning * Manganese cobalt spinel * Electrical conductivity * Plasma spray Subject RIV: JE - Non-nuclear Energetics, Energy Consumption ; Use Impact factor: 6.395, year: 2016 http://www.sciencedirect.com/science/article/pii/S0378775315305383

  7. A Grid-Based Cyber Infrastructure for High Performance Chemical Dynamics Simulations

    Directory of Open Access Journals (Sweden)

    Khadka Prashant

    2008-10-01

    Full Text Available Chemical dynamics simulation is an effective means to study atomic level motions of molecules, collections of molecules, liquids, surfaces, interfaces of materials, and chemical reactions. To make chemical dynamics simulations globally accessible to a broad range of users, recently a cyber infrastructure was developed that provides an online portal to VENUS, a popular chemical dynamics simulation program package, to allow people to submit simulation jobs that will be executed on the web server machine. In this paper, we report new developments of the cyber infrastructure for the improvement of its quality of service by dispatching the submitted simulations jobs from the web server machine onto a cluster of workstations for execution, and by adding an animation tool, which is optimized for animating the simulation results. The separation of the server machine from the simulation-running machine improves the service quality by increasing the capacity to serve more requests simultaneously with even reduced web response time, and allows the execution of large scale, time-consuming simulation jobs on the powerful workstation cluster. With the addition of an animation tool, the cyber infrastructure automatically converts, upon the selection of the user, some simulation results into an animation file that can be viewed on usual web browsers without requiring installation of any special software on the user computer. Since animation is essential for understanding the results of chemical dynamics simulations, this animation capacity provides a better way for understanding simulation details of the chemical dynamics. By combining computing resources at locations under different administrative controls, this cyber infrastructure constitutes a grid environment providing physically and administratively distributed functionalities through a single easy-to-use online portal

  8. [Studies on chemical protectors against radiation. XXXII. Protective effects of methanol extracts of various Taiwan crude drugs on radiation injuries].

    Science.gov (United States)

    Wang, C M; Ohta, S; Shinoda, M

    1990-11-01

    This study is to investigate radioprotective effects of 23 Taiwan crude drugs on X-ray induced bone marrow death and skin injury in mice. Each methanol extract of these Taiwan crude drugs was injected intraperitoneally into ICR male mice at 6 weeks of age before irradiation. Mice were whole-body irradiated with a soft X-ray generator. Radiation factors of the two screening tests used were as follows: 70 kVp, 10 mA, 10 mm acrylate filter, 70R/min, 2100R for survival test, and 30 kVp, 10 mA, 190R/min, 1100R for protective test on skin injury. As a result of these studies, the survival effect was recognized in Solani Incani Herba and Orthosiphi Aristati Herba. On the other hand, Mimosae Herba, Canarii Radix, Bombacis Radix, Arecae Fructus, Hedyotidis Diffusae Herba and Cynomorii Caulis were shown to have significant protective potency on skin injury.

  9. MOFabric: Electrospun Nanofiber Mats from PVDF/UiO-66-NH2 for Chemical Protection and Decontamination.

    Science.gov (United States)

    Lu, Annie Xi; McEntee, Monica; Browe, Matthew A; Hall, Morgan G; DeCoste, Jared B; Peterson, Gregory W

    2017-04-19

    Textiles capable of capture and detoxification of toxic chemicals, such as chemical-warfare agents (CWAs), are of high interest. Some metal-organic frameworks (MOFs) exhibit superior reactivity toward CWAs. However, it remains a challenge to integrate powder MOFs into engineered materials like textiles, while retaining functionalities like crystallinity, adsorptivity, and reactivity. Here, we present a simple method of electrospinning UiO-66-NH 2 , a zirconium MOF, with polyvinylidene fluoride (PVDF). The electrospun composite, which we refer to as "MOFabric", exhibits comparable crystal patterns, surface area, chlorine uptake, and simulant hydrolysis to powder UiO-66-NH 2 . The MOFabric is also capable of breaking down GD (O-pinacolyl methylphosphonofluoridae) faster than powder UiO-66-NH 2. Half-life of GD monitored by solid-state NMR for MOFabric is 131 min versus 315 min on powder UiO-66-NH 2 .

  10. Laboratory Performance of the Single-Sided E-A-R (registered trademark) Combat Arms Hearing Protective Earplug

    Science.gov (United States)

    2010-01-01

    Research article / Article de recherche LABORATORY PERFORMANCE OF THE SINGLE-SIDED EAR® COMBAT ARMS HEARING PROTECTIVE EARPLUG Sharon M. Abel and...external microphones for enhanced L:. -communication-? ;‘ V SOMMAIRE. Le but de cet article est de comparer 1 effet du port de bouchons conventionnels a...MA. Bekesy audiometry and loudness balance testing. In: Katz, J, editor. Handbook of clinical audiology . 3rd ed. Williams & Wilkins: Baltimore; 1985

  11. Guidelines for Use of Personal Protective Equipment by Law Enforcement Personnel During a Terrorist Chemical Agent Incident. Revision 2

    Science.gov (United States)

    2003-12-01

    dispersion models detailed by Stuempfle6. The nature of the missions identified for SWAT teams may require them to operate indoors where chemical...depressants (BZ, marijuana ) have a delayed action rate of 2 to 4 hours if inhaled, and up to 36 hours from skin absorption. • Persistency—BZ is very...persistent in soil, water, and on surfaces. • Odor—BZ has no odor. Marijuana has a distinct smell. • Primary hazard—Respiratory, skin absorption

  12. Physical and chemical protection of soil organic carbon in three agricultural soils with different contents of calcium carbonate

    International Nuclear Information System (INIS)

    Clough, A.; Skjemstad, J.O.

    2000-01-01

    The amount of organic carbon physically protected by entrapment within aggregates and through polyvalent cation organic matter bridging was determined on non-calcareous and calcareous soils. The composition of organic carbon in whole soils and 13 C NMR analysis. High energy photo-oxidation was carried out on <53 μm fractions and results from the NMR spectra showed 17-40% of organic carbon was in a condensed aromatic form, most likely charcoal (char). The concept that organic material remaining after photo-oxidation may be physically protected within aggregates was investigated by treating soils with a mild acid prior to photo-oxidation. More organic material was protected in the calcareous than the non-calcareous soils, regardless of whether the calcium occurred naturally or was an amendment. Acid treatment indicated that the presence of exchangeable calcium reduced losses of organic material upon photo-oxidation by about 7% due to calcium bridging. These results have implications for N fertiliser recommendations based upon organic carbon content. Firstly, calcium does not impact upon degradability of organic material to an extent likely to affect N fertiliser recommendations. Secondly, standard assessment techniques overestimate active organic carbon content in soils with high char content. Copyright (2000) CSIRO Publishing

  13. River Protection Project waste feed delivery program technical performance measurement assessment plan

    International Nuclear Information System (INIS)

    O'TOOLE, S.M.

    1999-01-01

    This plan establishes a formal technical performance-monitoring program. Technical performance is assessed by establishing requirements based performance goals at the beginning of a program and routinely evaluating progress in meeting these goals at predetermined milestones throughout the project life cycle

  14. Preparation and thermal performance of paraffin/Nano-SiO2 nanocomposite for passive thermal protection of electronic devices

    International Nuclear Information System (INIS)

    Wang, Yaqin; Gao, Xuenong; Chen, Peng; Huang, Zhaowen; Xu, Tao; Fang, Yutang; Zhang, Zhengguo

    2016-01-01

    Highlights: • Three types of paraffin/nano-SiO 2 nanocomposites were prepared and characterized. • Thermo-physical properties of these composites were determined and compared. • One composite with lower thermal conductivity showed better thermal insulation properties. • This composite was identified as thermal insulation material for electronic components. - Abstract: In this paper, three grades of nano silicon dioxide (nano-SiO 2 ), NS1, NS2 and NS3, were mixed into paraffin to prepare nanocomposites as novel insulation materials for electronic passive thermal protection applications. The optimal mass percentages of paraffin for the three composites, NS1P, NS2P and NS3P, were determined to be 75%, 70% and 65%, respectively. Investigations by means of scanning electron micrographs (SEM), differential scanning calorimeter (DSC), thermogravimetric analysis (TG), hot disk analyzer and thermal protection performance tests were devoted to the morphology, thermal properties and thermal protection performance analysis of composites. Experimental results showed that paraffin uniformly distributed into the pores and on the surface of nano-SiO 2 . Melting points of composites declined and experimental latent heat became lower than the calculated values with the decrease of nano-SiO 2 pore size. The NS1P composite had larger thermal storage capacity, better reliability and stability compared with NS2P and NS3P. In addition, compared with 90% wt.% paraffin/EG composite, the incorporation of NS1 (25 wt.%) into paraffin caused not only 63.2% reduction in thermal conductivity, but also 21.8% increase in thermal protection time affected by the ambient temperature. Thus those good properties confirmed that NS1P (75 wt.%) composite was a viable candidate for protecting electronic devices under high temperature environment.

  15. Chemical Reactive Anchoring Lipids with Different Performance for Cell Surface Re-engineering Application.

    Science.gov (United States)

    Vabbilisetty, Pratima; Boron, Mallorie; Nie, Huan; Ozhegov, Evgeny; Sun, Xue-Long

    2018-02-28

    Introduction of selectively chemical reactive groups at the cell surface enables site-specific cell surface labeling and modification opportunity, thus facilitating the capability to study the cell surface molecular structure and function and the molecular mechanism it underlies. Further, it offers the opportunity to change or improve a cell's functionality for interest of choice. In this study, two chemical reactive anchor lipids, phosphatidylethanolamine-poly(ethylene glycol)-dibenzocyclooctyne (DSPE-PEG 2000 -DBCO) and cholesterol-PEG-dibenzocyclooctyne (CHOL-PEG 2000 -DBCO) were synthesized and their potential application for cell surface re-engineering via lipid fusion were assessed with RAW 264.7 cells as a model cell. Briefly, RAW 264.7 cells were incubated with anchor lipids under various concentrations and at different incubation times. The successful incorporation of the chemical reactive anchor lipids was confirmed by biotinylation via copper-free click chemistry, followed by streptavidin-fluorescein isothiocyanate binding. In comparison, the cholesterol-based anchor lipid afforded a higher cell membrane incorporation efficiency with less internalization than the phospholipid-based anchor lipid. Low cytotoxicity of both anchor lipids upon incorporation into the RAW 264.7 cells was observed. Further, the cell membrane residence time of the cholesterol-based anchor lipid was evaluated with confocal microscopy. This study suggests the potential cell surface re-engineering applications of the chemical reactive anchor lipids.

  16. The effect of gas permeation through vertical membranes on chemical switching reforming (CSR) reactor performance

    NARCIS (Netherlands)

    Wassie, S.A.; Gallucci, F.; Cloete, S.; Zaabout, A.; van Sint Annaland, M.; Amini, S.

    2016-01-01

    A novel membrane assisted fluidized bed reactor concept has been proposed for ultra-pure hydrogen production with integrated CO2 capture from steam methane reforming. The so-called Chemical Switching Reactor (CSR) concept combines the use of an oxygen carrier for supplying heat and catalysing the

  17. Performance of two swine manure treatment systems on chemical composition and on the reduction of pathogens.

    Science.gov (United States)

    Viancelli, A; Kunz, A; Steinmetz, R L R; Kich, J D; Souza, C K; Canal, C W; Coldebella, A; Esteves, P A; Barardi, C R M

    2013-01-01

    Swine effluents must be correctly handled to avoid negative environmental impacts. In this study, the profiles of two swine manure treatment systems were evaluated: a solid-liquid separation step, followed by an anaerobic reactor, and an aerobic step (System 1); and a biodigester followed by serial lagoons (System 2). Both systems were described by the assessment of chemical, bacterial and viral parameters. The results showed that in System 1, there was reduction of chemicals (COD, phosphorus, total Kjeldhal nitrogen - TKN - and NH(3)), total coliforms and Escherichia coli; however, the same reduction was not observed for Salmonella sp. Viral particles were significantly reduced but not totally eliminated from the effluent. In System 2, there was a reduction of chemicals, bacteria and viruses with no detection of Salmonella sp., circovirus, parvovirus, and torque teno virus in the effluent. The chemical results indicate that the treated effluent can be reused for cleaning swine facilities. However, the microbiological results show a need of additional treatment to achieve a complete inactivation for cases when direct contact with animals is required. Copyright © 2012 Elsevier Ltd. All rights reserved.

  18. Chemical Annealing of Zinc Tetraphenylporphyrin Films: Effects on Film Morphology and Organic Photovoltaic Performance

    KAUST Repository

    Trinh, Cong; Whited, Matthew T.; Steiner, Andrew; Tassone, Christopher J.; Toney, Michael F.; Thompson, Mark E.

    2012-01-01

    We present a chemical annealing process for organic thin films. In this process, a thin film of a molecular material, such as zinc tetraphenylporphyrin (ZnTPP), is exposed to a vapor of nitrogen-based ligand (e.g., pyrazine, pz, and triazine, tz

  19. Automated and unbiased classification of chemical profiles from fungi using high performance liquid chromatography

    DEFF Research Database (Denmark)

    Hansen, Michael Edberg; Andersen, Birgitte; Smedsgaard, Jørn

    2005-01-01

    In this paper we present a method for unbiased/unsupervised classification and identification of closely related fungi, using chemical analysis of secondary metabolite profiles created by HPLC with UV diode array detection. For two chromatographic data matrices a vector of locally aligned full sp...

  20. Effect of USY zeolite chemical treatment with ammonium nitrate on its VGO hydrocracking performance

    NARCIS (Netherlands)

    Agudelo, J.L.; Hensen, Emiel; Giraldo, S.A.; Hoyos, L.J.

    2016-01-01

    Chemically modified USY zeolites were obtained by ammonium nitrate (AN) treatment under hydrothermal conditions. AN treatment considerably enhanced the mesopore volume of the parent steam-treated zeolite. This treatment also caused the creation of extraframework species of weak acid nature.

  1. Chemical Reactive Anchoring Lipids with Different Performance for Cell Surface Re-engineering Application

    Science.gov (United States)

    2018-01-01

    Introduction of selectively chemical reactive groups at the cell surface enables site-specific cell surface labeling and modification opportunity, thus facilitating the capability to study the cell surface molecular structure and function and the molecular mechanism it underlies. Further, it offers the opportunity to change or improve a cell’s functionality for interest of choice. In this study, two chemical reactive anchor lipids, phosphatidylethanolamine–poly(ethylene glycol)–dibenzocyclooctyne (DSPE–PEG2000–DBCO) and cholesterol–PEG–dibenzocyclooctyne (CHOL–PEG2000–DBCO) were synthesized and their potential application for cell surface re-engineering via lipid fusion were assessed with RAW 264.7 cells as a model cell. Briefly, RAW 264.7 cells were incubated with anchor lipids under various concentrations and at different incubation times. The successful incorporation of the chemical reactive anchor lipids was confirmed by biotinylation via copper-free click chemistry, followed by streptavidin-fluorescein isothiocyanate binding. In comparison, the cholesterol-based anchor lipid afforded a higher cell membrane incorporation efficiency with less internalization than the phospholipid-based anchor lipid. Low cytotoxicity of both anchor lipids upon incorporation into the RAW 264.7 cells was observed. Further, the cell membrane residence time of the cholesterol-based anchor lipid was evaluated with confocal microscopy. This study suggests the potential cell surface re-engineering applications of the chemical reactive anchor lipids. PMID:29503972

  2. Further Relationships Between Blood Chemical Values and College Student Performance and Attitudes.

    Science.gov (United States)

    Lindeman, Richard H.; And Others

    Blood serum uric acid and cholesterol levels in the blood were studied in relation to inner drive and external pressures of college students in the U.S.A. and in Sweden. Subjects for the study included 210 American and 78 Swedish male and female college students and 138 college football players. The blood chemicals were measured by Technicon…

  3. Surface-modified polymeric pads for enhanced performance during chemical mechanical planarization

    International Nuclear Information System (INIS)

    Deshpande, S.; Dakshinamurthy, S.; Kuiry, S.C.; Vaidyanathan, R.; Obeng, Y.S.; Seal, S.

    2005-01-01

    The chemical mechanical planarization (CMP) process occurs at an atomic level at the slurry/wafer interface and hence slurries and polishing pads play a critical role in their successful implementation. Polyurethane is a commonly used polymer in the manufacturing of CMP pads. These pads are incompatible with some chemicals present in the CMP slurries, such as hydrogen peroxide. To overcome these problems, Psiloquest has developed new Application Specific Pads (ASP). Surface of such pads has been modified by depositing a thin film of tetraethyl orthosilicate using plasma-enhanced chemical vapor deposition (PECVD) process. In the present study, mechanical properties of such coated pads have been investigated using nanoindentation. The surface morphology and the chemistry of the ASP were studied using scanning electron microcopy, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy techniques. It was observed that mechanical and chemical properties of the pad top surface are a function of the PECVD coating time. Such PECVD-treated pads are found to be hydrophilic and do not require storage in aqueous media during the not-in-use period. The metal removal rate using such surface-modified polishing pads was found to increase linearly with the PECVD coating time

  4. A performance study of radio-opaque personal protective fabrics for the reduction of transmittance of gamma-rays and neutrons

    International Nuclear Information System (INIS)

    Corcoran, E.C.; William Forest; Robert Horton; Kelly, D.G.; Kristine Mattson; Curtis McDonald; Nielsen, K.S.; Kristin Topping; Weir, R.D.; Andre Yonkeu

    2012-01-01

    Commercial radio-opaque combat (CRC) fabrics, for incorporation into personal protective equipment used by first responders and armed forces, are marketed as having the ability to provide a level of protection against specific types of radiation. For a CRC material, a standard combat uniform and a multi-layered chemical, biological, radiological, nuclear (CBRN) protective material, the present work examines chemical composition and radiation protection against gamma-rays and neutron fluxes. Significant reduction in gamma-ray transmittance occurs only for the CRC fabric (46-514 keV) with gamma-ray attenuation coefficients of 3.10 to 2 g -1 . Reduction in neutron transmittance, for all three fabrics, could not be assessed with certainty as the measured transmittance was obscured by large statistical uncertainties. (author)

  5. Vol. 34 - Optimization of quench protection heater performance in high-field accelerator magnets through computational and experimental analysis

    CERN Document Server

    Salmi, Tiina

    2016-01-01

    Superconducting accelerator magnets with increasingly hi gh magnetic fields are being designed to improve the performance of the Large Hadron Collider (LHC) at CERN. One of the technical challenges is the magnet quench p rotection, i.e., preventing damage in the case of an unexpected loss of superc onductivity and the heat generation related to that. Traditionally this is d one by disconnecting the magnet current supply and using so-called protection he aters. The heaters suppress the superconducting state across a large fraction of the winding thus leading to a uniform dissipation of the stored energy. Preli minary studies suggested that the high-field Nb 3 Sn magnets under development for the LHC luminosity upgrade (HiLumi) could not be reliably protected using the existing heaters. In this thesis work I analyzed in detail the present state-of-the-art protection heater technology, aiming to optimize its perfo rmance and evaluate the prospects in high-field magnet protection. The heater efficiency analyses ...

  6. Minocycline and doxycycline, but not other tetracycline-derived compounds, protect liver cells from chemical hypoxia and ischemia/reperfusion injury by inhibition of the mitochondrial calcium uniporter

    International Nuclear Information System (INIS)

    Schwartz, Justin; Holmuhamedov, Ekhson; Zhang, Xun; Lovelace, Gregory L.; Smith, Charles D.; Lemasters, John J.

    2013-01-01

    Minocycline, a tetracycline-derived compound, mitigates damage caused by ischemia/reperfusion (I/R) injury. Here, 19 tetracycline-derived compounds were screened in comparison to minocycline for their ability to protect hepatocytes against damage from chemical hypoxia and I/R injury. Cultured rat hepatocytes were incubated with 50 μM of each tetracycline-derived compound 20 min prior to exposure to 500 μM iodoacetic acid plus 1 mM KCN (chemical hypoxia). In other experiments, hepatocytes were incubated in anoxic Krebs–Ringer–HEPES buffer at pH 6.2 for 4 h prior to reoxygenation at pH 7.4 (simulated I/R). Tetracycline-derived compounds were added 20 min prior to reperfusion. Ca 2+ uptake was measured in isolated rat liver mitochondria incubated with Fluo-5N. Cell killing after 120 min of chemical hypoxia measured by propidium iodide (PI) fluorometry was 87%, which decreased to 28% and 42% with minocycline and doxycycline, respectively. After I/R, cell killing at 120 min decreased from 79% with vehicle to 43% and 49% with minocycline and doxycycline. No other tested compound decreased killing. Minocycline and doxycycline also inhibited mitochondrial Ca 2+ uptake and suppressed the Ca 2+ -induced mitochondrial permeability transition (MPT), the penultimate cause of cell death in reperfusion injury. Ru360, a specific inhibitor of the mitochondrial calcium uniporter (MCU), also decreased cell killing after hypoxia and I/R and blocked mitochondrial Ca 2+ uptake and the MPT. Other proposed mechanisms, including mitochondrial depolarization and matrix metalloprotease inhibition, could not account for cytoprotection. Taken together, these results indicate that minocycline and doxycycline are cytoprotective by way of inhibition of MCU. - Highlights: • Minocycline and doxycycline are the only cytoprotective tetracyclines of those tested • Cytoprotective tetracyclines inhibit the MPT and mitochondrial calcium and iron uptake. • Cytoprotective tetracyclines protect

  7. Minocycline and doxycycline, but not other tetracycline-derived compounds, protect liver cells from chemical hypoxia and ischemia/reperfusion injury by inhibition of the mitochondrial calcium uniporter

    Energy Technology Data Exchange (ETDEWEB)

    Schwartz, Justin; Holmuhamedov, Ekhson; Zhang, Xun; Lovelace, Gregory L.; Smith, Charles D. [Department of Drug Discovery and Biomedical Sciences, Medical University of South Carolina, Charleston, SC (United States); Lemasters, John J., E-mail: JJLemasters@musc.edu [Department of Drug Discovery and Biomedical Sciences, Medical University of South Carolina, Charleston, SC (United States); Department of Biochemistry and Molecular Biology, Medical University of South Carolina, Charleston, SC (United States)

    2013-11-15

    Minocycline, a tetracycline-derived compound, mitigates damage caused by ischemia/reperfusion (I/R) injury. Here, 19 tetracycline-derived compounds were screened in comparison to minocycline for their ability to protect hepatocytes against damage from chemical hypoxia and I/R injury. Cultured rat hepatocytes were incubated with 50 μM of each tetracycline-derived compound 20 min prior to exposure to 500 μM iodoacetic acid plus 1 mM KCN (chemical hypoxia). In other experiments, hepatocytes were incubated in anoxic Krebs–Ringer–HEPES buffer at pH 6.2 for 4 h prior to reoxygenation at pH 7.4 (simulated I/R). Tetracycline-derived compounds were added 20 min prior to reperfusion. Ca{sup 2+} uptake was measured in isolated rat liver mitochondria incubated with Fluo-5N. Cell killing after 120 min of chemical hypoxia measured by propidium iodide (PI) fluorometry was 87%, which decreased to 28% and 42% with minocycline and doxycycline, respectively. After I/R, cell killing at 120 min decreased from 79% with vehicle to 43% and 49% with minocycline and doxycycline. No other tested compound decreased killing. Minocycline and doxycycline also inhibited mitochondrial Ca{sup 2+} uptake and suppressed the Ca{sup 2+}-induced mitochondrial permeability transition (MPT), the penultimate cause of cell death in reperfusion injury. Ru360, a specific inhibitor of the mitochondrial calcium uniporter (MCU), also decreased cell killing after hypoxia and I/R and blocked mitochondrial Ca{sup 2+} uptake and the MPT. Other proposed mechanisms, including mitochondrial depolarization and matrix metalloprotease inhibition, could not account for cytoprotection. Taken together, these results indicate that minocycline and doxycycline are cytoprotective by way of inhibition of MCU. - Highlights: • Minocycline and doxycycline are the only cytoprotective tetracyclines of those tested • Cytoprotective tetracyclines inhibit the MPT and mitochondrial calcium and iron uptake. • Cytoprotective

  8. U.S. and Russian cooperative efforts to enhance nuclear material protection, control, and accountability at the Siberian Chemical Combine at Tomsk-7

    International Nuclear Information System (INIS)

    Kreykes, J.; Petrushev, V.I.; Griggs, J.

    1996-01-01

    The US partners in the Laboratory-to-Laboratory Program in Nuclear Materials Protection, Control, and Accountability (MPC and A) have reached signed agreements with the Siberian Chemical Combine (SKhK) to rapidly enhance the protection, control, and accountability of nuclear material at all of its facilities. SKhK is the largest multi-function production center of the Russian nuclear complex and, until recently, its facilities produced and processed special nuclear materials for the Russian Defense Ministry. SKhK produces heat and electricity, enriches uranium for commercial reactor fuel, reprocesses irradiated fuel, and converts highly enriched uranium metal into oxide for blending into low-enriched reactor-grade uranium, and manufactures civilian products. SKhK is aggressively pursuing a program to enhance MPC and A which includes the installation of pedestrian and vehicle radiation monitors, rapid inventory methods, tamper-indicating devices, computerized accounting systems, and physical protection measures. This work is a collaboration between technical experts from Brookhaven, Lawrence Livermore, Los Alamos, Oak Ridge, pacific Northwest, and Sandia National Laboratories and their Russian counterparts at SKhK. This paper reviews the status of this initial effort and outlines plans for continuing the work in 1996

  9. Efficacy of chemically characterized Foeniculum vulgare Mill seed essential oil in protection of raw tobacco leaves during storage against fungal and aflatoxin contamination.

    Science.gov (United States)

    Kedia, A; Dwivedy, A K; Pandey, A K; Kumar, R R; Regmi, P; Dubey, N K

    2015-10-01

    To report fungal and aflatoxin contamination in stored tobacco leaves and the potential of Foeniculum vulgare (fennel) seed essential oil (EO) as a plant-based preservative in protection of tobacco during storage. Mycological analysis of tobacco samples was done by surface sterilization and serial dilution tests. The Aspergillus flavus isolates were screened for their toxigenicity. Both in vivo and in vitro tests were done to evaluate antifungal and antiaflatoxigenic efficacy of chemically characterized EO. The mycoflora analysis revealed 108 fungal colonies belonging to five genera and nine species. All A. flavus isolates were found aflatoxigenic during screening. Gas chromatography and mass spectrometry analysis of EO identified 19 components (99·66%); estragole being the major component (47·49%). The EO showed broad fungitoxicity at 1·25 μl ml(-1) and 100% inhibition to AFB1 production as well as ergosterol synthesis at 1·0 μl ml(-1) concentration. EO showed 100% protection of stored tobacco samples from aflatoxin B1 contamination. The fennel EO can thus be formulated as a plant-based preservative for food items. The present investigation comprises the first report on antiaflatoxin efficacy of fennel oil and its potency in the protection of tobacco leaves from fungal and aflatoxin contamination during storage. © 2015 The Society for Applied Microbiology.

  10. Cutaneous challenge with chemical warfare agents in the SKH-1 hairless mouse. (I) Development of a model for screening studies in skin decontamination and protection.

    Science.gov (United States)

    Dorandeu, F; Taysse, L; Boudry, I; Foquin, A; Hérodin, F; Mathieu, J; Daulon, S; Cruz, C; Lallement, G

    2011-06-01

    Exposure to lethal chemical warfare agents (CWAs) is no longer only a military issue due to the terrorist threat. Among the CWAs of concern are the organophosphorus nerve agent O-ethyl-S-(2[di-isopropylamino]ethyl)methyl-phosphonothioate (VX) and the vesicant sulfur mustard (SM). Although efficient means of decontamination are available, most of them lose their efficacy when decontamination is delayed after exposure of the bare skin. Alternatively, CWA skin penetration can be prevented by topical skin protectants. Active research in skin protection and decontamination is thus paramount. In vivo screening of decontaminants or skin protectants is usually time consuming and may be expensive depending on the animal species used. We were thus looking for a suitable, scientifically sound and cost-effective model, which is easy to handle. The euthymic hairless mouse Crl: SKH-1 (hr/hr) BR is widely used in some skin studies and has previously been described to be suitable for some experiments involving SM or SM analogs. To evaluate the response of this species, we studied the consequences of exposing male anaesthetized SKH-1 mice to either liquid VX or to SM, the latter being used in liquid form or as saturated vapours. Long-term effects of SM burn were also evaluated. The model was then used in the companion paper (Taysse et al.(1)).

  11. Study on radiation dose and its protection for the physician performing the retrograde urethrography for male

    International Nuclear Information System (INIS)

    Inui, Saburo; Suzuki, Toshiyuki; Kashino, Teiichi; Abe, Hitoshi.

    1982-01-01

    The status quo of the various techniques used in retrograde urethrography (R.U.) is examined by the questionnaire method with the data of radiation doses to medical personnels, and new methods are devised to reduce unnecessary radiation dose. Manual injection of the radio-opaquee contrast medium has been employed by 92.5% out of 8,259 physicians in 67 institutions. They expose themselves as well as patients to the radiation during the course of the examination. In most of these occasions the physician is not sufficiently protected from radiation leaving the possibility of his somatic damage. From these observations, the followings were studied: 1) Application of our newly developed protective barrier, exclusive for R.U., made of lead-impregnated acryl-resin plate (KYOW GLAS-XA). 2) Employment of the high speed screen made of rare earth metal. The results were encouraging in reducing the radiation exposure dose. In conclusion, the employment of the above two methods are efficient in obviating unnecessary radiation exposure to the physician during R.U. (author)

  12. Development of a combined piezoresistive pressure and temperature sensor using a chemical protective coating for Kraft pulp digester process monitoring

    International Nuclear Information System (INIS)

    Mohammadi, Abdolreza R; Chiao, Mu; Bennington, Chad P J

    2011-01-01

    We have developed an integrated piezoresistive pressure and temperature sensor for multiphase chemical reactors, primarily Kraft pulp digesters (pH 13.5, temperatures up to 175 °C, reaching a local maximum of 180 °C and pressures up to 2 MPa). The absolute piezoresistive pressure sensor consisted of a large square silicon diaphragm (1000 × 1000 µm 2 ) and high resistance piezoresistors (10 000 Ω). A 4500 Ω buried piezoresistive wire was patterned on the silicon chip to form a piezoresistive temperature sensor which was used for pressure sensor compensation and temperature measurement. A 4 µm thick Parylene HT® coating, a chemically resistant epoxy and a silicone conformal coating were deposited to passivate the pressure sensor against the caustic environment in Kraft digesters. The sensors were characterized up to 2 MPa and 180 °C in an environment chamber. A maximum thermal error of ±0.72% full-scale output (FSO), an average sensitivity of 0.116 mV (V kPa) −1 and a power consumption of 0.3 mW were measured in the pressure sensor. The sensors' resistances were measured before and after test in a Kraft pulping cycle and showed no change in their values. SEM pictures and topographical surfaces were also analyzed before and after pulp liquor exposure and showed no observable changes.

  13. Optimization of solar cell performance using atmospheric pressure chemical vapour deposition deposited TCOs

    Czech Academy of Sciences Publication Activity Database

    Yates, H.M.; Evans, P.; Sheel, D.W.; Hodgkinson, J.L.; Sheel, P.; Dagkaldiran, U.; Gordijn, A.; Finger, F.; Remeš, Zdeněk; Vaněček, Milan

    2009-01-01

    Roč. 25, č. 8 (2009), s. 789-796 ISSN 1938-5862. [International Chemical Vapor Deposition Symposium (CVD-XVII) /17./. Wien, 04.10.2009-09.10.2009] Grant - others:European Community(XE) Project (STREP) of the 6. FP Institutional research plan: CEZ:AV0Z10100521 Keywords : solar cells * TCO * CVD Subject RIV: BM - Solid Matter Physics ; Magnetism

  14. Candidates Profile in FUVEST Exams from 2004 to 2013: Private and Public School Distribution, FUVEST Average Performance and Chemical Equilibrium Tasks Performance

    Directory of Open Access Journals (Sweden)

    R.S.A.P. Oliveira

    2014-08-01

    Full Text Available INTRODUCTION. Chemical equilibrium is recognized as a topic of several misconceptions. Its origins must be tracked from previous scholarship. Its impact on biochemistry learning is not fully described. A possible bulk of data is the FUVEST exam. OBJECTIVES: Identify students’ errors profile on chemical equilibrium tasks using public data from FUVEST exam. MATERIAL AND METHODS: Data analysis from FUVEST were: i Private and Public school distribution in Elementary and Middle School, and High School candidates of Pharmacy-Biochemistry course and total USP careers until the last call for enrollment (2004-2013; ii Average performance in 1st and 2nd parts of FUVEST exam of Pharmacy-Biochemistry, Chemistry, Engineering, Biological Sciences, Languages and Medicine courses and total enrolled candidates until 1st call for enrollment (2008- 2013; iii Performance of candidates of Pharmacy-Biochemistry, Chemistry, Engineering, Biological Sciences, Languages and Medicine courses and total USP careers in chemical equilibrium issues from 1st part of FUVEST (2011-2013. RESULTS AND DISCUSSION: i 66.2% of candidates came from private Elementary-Middle School courses and 71.8%, came from High School courses; ii Average grade over the period for 1st and 2nd FUVEST parts are respectively (in 100 points: Pharmacy-Biochemistry 66.7 and 61.2, Chemistry 65.9 and 58.9, Engineering 75.9 and 71.9, Biological Sciences 65.6 and 54.6, Languages 49.9 and 43.3, Medicine 83.5 and 79.5, total enrolled candidates 51,5 and 48.9; iii Four chemical equilibrium issues were found during 2011-2013 and the analysis of multiplechoice percentage distribution over the courses showed that there was a similar performance of students among them, except for Engineering and Medicine with higher grades, but the same proportional distribution among choices. CONCLUSION: Approved students came majorly from private schools. There was a different average performance among courses and similar on

  15. Use and Protection of GPS Sidelobe Signals for Enhanced Navigation Performance in High Earth Orbit

    Science.gov (United States)

    Parker, Joel J. K.; Valdez, Jennifer E.; Bauer, Frank H.; Moreau, Michael C.

    2016-01-01

    GPS (Global Positioning System) Space Service Volume (SSV) signal environment is from 3,000-36,000 kilometers altitude. Current SSV specifications only capture performance provided by signals transmitted within 23.5(L1) or 26(L2-L5) off-nadir angle. Recent on-orbit data lessons learned show significant PNT (Positioning, Navigation and Timing) performance improvements when the full aggregate signal is used. Numerous military civil operational missions in High Geosynchronous Earth Orbit (HEOGEO) utilize the full signal to enhance vehicle PNT performance

  16. Stimulation or Inhibition Conflicting evidence for (±)-catechin’s role as a chemical facilitator and disease protecting agent

    Science.gov (United States)

    Venkatachalam, L; Biedrzycki, Meredith L

    2010-01-01

    The occurrence of plant hormesis is a poorly understood phenomenon, wherein low doses of phytotoxins unusually promote growth responses in higher plants. In contrast, negative plant-plant interactions mediated through secreted small molecular weight compounds initiate growth inhibitory responses. Studies related to (±)-catechin mediated allelopathy have transpired both novel information and generated significant controversy. Specifically, studies related to the phytotoxicity responses mediated by (±)-catechins have been seriously debated. The pronged opinion that (±)-catechin is phytotoxic versus non-phytotoxic relies more on the target plant systems and the conditions used to test phytotoxic responses. It is reported that lower than MIC dosage supplementation of (±)-catechin could promote growth responses in the model plant Arabidopsis thaliana. Furthermore, it was shown that sub-MIC levels of (±)-catechin supplementation leads to elicitation of disease resistance against Pseudomonas syringae DC3000 (hereafter DC3000). Intrigued by the unique hormesis response observed, we tested whether (±)-catechin indeed promotes growth responses in A. thaliana. In our hands, we observed no growth promotion responses of (±)-catechin against A. thaliana under in vitro or in soil conditions. We also evaluated the previously reported disease protecting properties of (±)-catechin in A. thaliana against DC3000. The systematic observations to evaluate disease protecting properties entailing colony counts, disease incidences and loss of chlorophyll studies showed no disease protecting properties of (±)-catechin. The transcriptional response for a marker pathogenesis related PR1 defense gene showed no induction post (±)-catechin supplementation. The cell death genes (AC D2 and CA D1) associated with programmed cell death revealed unchanged expression levels in plants treated with sub-MIC levels of (±)-catechin. Further, we report supplementation of sub-MIC levels of (

  17. A Study on Performance Evaluation of Safety-Related Protective Coating for Yonggwang Unit 1 and 2

    International Nuclear Information System (INIS)

    Kim, Sung Young; Kim, Young Bum; Lee, Won Sang

    2010-01-01

    Protective coating inside nuclear power plants could find its origin from NRC Reg. Guide 1.82(Rev. 3) regarding current issue for the regulation of foreign materials inside containment building. The current issue for the regulation of foreign materials inside containment considered/determined the current issues only regarding the blockage of sump screen by foreign materials such as coating material, insulator, and other materials, while safety-related coating is separately managed by NRC Reg. Guide 1.54(Rev. 1). In this study, we performed field walk-down to evaluate the as-is condition of protective coating inside containment building which was classified as for structure and for equipment with applying the requirement for safety-related coating

  18. Impact analysis of the implemented quality management system on business performances in pharmaceutical-chemical industry in Serbia

    Directory of Open Access Journals (Sweden)

    Marinković Valentina D.

    2013-01-01

    Full Text Available International quality management standard (QMS ISO 9001 became widely accepted as a framework for product and/or services quality improvement. There are recent research conducted in order to define relationships and effects between the applied QMS and financial and/or non-financial business parameters. The effects of the applied pharmaceutical quality system (PQS on the business performances in Serbian pharmaceutical-chemical industry are analyzed in this paper using multivariate linear regression analysis. The empirical data were collected using a survey that was performed among experts from Serbian pharmaceutical-chemical industrial sector during 2010. An extensive questionnaire was used in the survey, grouping the questions in eight groups: Implementation of pharmaceutical quality system (AQ, Quality/strategy planning (QP, Human resource management (HR, Supply management (SM, Customer focus (CF, Process management (PM, Continuous improvement (CI, and Business results (BR. The primary goal of the research was to analyze the effects of the elements of first seven groups (AQ, QP, HR, SM, CF, PM, and CI that present various aspects of the implementation of PQS, on the elements of business results (BR. Based on empirical data, regression relations were formed to present the effects of all considered elements of PQS implementation on the business performance parameters (BR. The positive effects of PQS implementation on the business performances such as the assessment of performance indicators, continual products and/or services quality improvement, and efficient problem solving, are confirmed in the presented research for the Serbian pharmaceutical-chemical industrial sector. The results of the presented research will create a room for the improvement of the existing models in application, and for attracting interested parties that aim to commence this business standardization process. Hence, implementation of PQS is not only the regulatory

  19. Ballistic Performance of Porous Ceramic Thermal Protection Systems at 9 km/s

    Science.gov (United States)

    Miller, Joshua E.; Bohl, W. E.; Foreman, C. D.; Christiansen, Eric L.; Davis, B. A.

    2009-01-01

    Porous-ceramic, thermal-protection-systems are used heavily in current reentry vehicles like the Orbiter, and they are currently being proposed for the next generation of manned spacecraft, Orion. These materials insulate the structural components and sensitive electronic components of a spacecraft against the intense thermal environments of atmospheric reentry. Furthermore, these materials are also highly exposed to space environmental hazards like meteoroid and orbital debris impacts. This paper discusses recent impact testing up to 9 km/s on ceramic tiles similar to those used on the Orbiter. These tiles have a porous-batting of nominally 8 lb/cubic ft alumina-fiber-enhanced-thermal-barrier (AETB8) insulating material coated with a damage-resistant, toughened-unipiece-fibrous-insulation (TUFI) layer.

  20. Ballistic Performance of Porous-Ceramic, Thermal Protection Systems to 9 km/s

    Science.gov (United States)

    Miller, Joshua E.; Bohl, William E.; Foreman, Cory D.; Christiansen, Eric C.; Davis, Bruce A.

    2010-01-01

    Porous-ceramic, thermal protection systems are used heavily in current reentry vehicles like the Orbiter, and they are currently being proposed for the next generation of US manned spacecraft, Orion. These materials insulate the structural components and sensitive components of a spacecraft against the intense thermal environments of atmospheric reentry. These materials are also highly exposed to solid particle space environment hazards. This paper discusses recent impact testing up to 9.65 km/s on ceramic tiles similar to those used on the Orbiter. These tiles are a porous-ceramic insulator of nominally 8 lb/ft(exp 3) alumina-fiber-enhanced-thermal-barrier (AETB8) coated with a damage-resistant, toughened-unipiece-fibrous-insulation/reaction-cured-glass layer (TUFI/RCG).

  1. Performance Assessment of Chemical Coagulation Together with Advanced Oxidation Peroxone Regarding Dye Wastewater Treatment of Appliance Factories

    Directory of Open Access Journals (Sweden)

    A R Shahriyari Farfani

    2016-01-01

    Full Text Available Abstract Introduction: Considering the important role of industry in polluting the environment, the present study aimed to evaluate the performance of chemical coagulation together with advanced oxidation (peroxone regarding dye wastewater treatment of appliance factories. Methods: This study was experimental, which it’s pilot-scale was conducted on the wastewater of the painting appliance Factory. The sample was selected via the combined sampling procedure. The processes used in the present study consisted of chemical coagulation and advanced oxidation (peroxone processes and 250 samples were analyzed. MgCl2, PAC and FeCl3, Bentonite, Cationic Polymer were used for chemical coagulation. The used equipments consisted of Spectrophotometer DR 2000, Jar taste and a ozonation reactor. COD and dye of samples were measured according to standard method. Results: The results revealed that each of the coagulants in its optimal pH were able to arrange the magnesium chloride 86.85%, poly aluminum chloride 88.47% and ferric chloride 85.41% in removal of COD. Poly aluminum chloride achieved the highest dye removal 90.92%. Furthermore, the highest COD removal efficiency was related to the combination of magnesium chloride (1.4 mg/l, poly aluminum chloride (0.6 mg/l and cationic polymers (0.4 mg/l with an efficiency of 89.11%, which managed to remove the dye up to 93.38%. COD removal efficiency reached to 99.67% using advanced oxidation process by peroxone method on pretreated wastewater (with chemical coagulation. Conclusions: For better performance of peroxone treatment, the wastewater should be pretreated for removal of dissolved solids. As a result, due to its suspension status of using peroxone method together chemical coagulation has a high capability to remove COD and dye from appliance Factore ,s wastewater.

  2. A fast chemical route for the synthesis of TBHQ functionalized reduced graphene oxide and its electrochemical performances

    Energy Technology Data Exchange (ETDEWEB)

    Rana, Subhasis; Sen, Pintu, E-mail: psen@vecc.gov.in; Bandyopadhyay, S.K.

    2016-02-01

    A fast chemical route for the synthesis of tertiary butyl hydroquinone (TBHQ) functionalized reduced graphene oxide (FRGO) and their application as high performance electrode materials for supercapacitors have been reported. Reductions of chemically exfoliated graphene oxides (GO) in the presence of small amount of TBHQ (1–2 wt % with respect to GO) at various time periods were investigated through XRD, FTIR and Raman studies. Reappearance of broad diffraction peak close to graphite peak (002) reveals an efficient method of reduction of different oxygen containing functional groups present in GO/FGO resulting in a decrease of interlayer d-spacing (∼3.5 Å). Absence of the absorption peaks in FTIR for –C=O, t-O–H, epoxide and alkoxy groups supports the complete reduction of GO to FRGO by hydrazine hydrate within a short time period of 4 h reduction under reflux condition. A large red shift in UV spectrum of FRGO – 4 h (270 nm) reveals the complete reduction of graphene oxide. The average crystallite sp{sup 2} domains sizes have been estimated through Raman spectroscopy. Plausible mechanism of TBHQ assisted fast chemical reduction of FGO has been enumerated. 1.5 wt % TBHQ in FRGO shows the best electrochemical performance where TBHQ not only acts as a reducing agent during functionalization, but also plays as an active redox molecule for enhanced capacitance of 200 F/g. - Highlights: • A fast chemical route has been adopted for the synthesis of TBHQ functionalized RGO. • The kinetics of chemical reduction becomes faster in the presence of TBHQ. • The FTIR spectrum of functionalized RGO supports the complete reduction process. • TBHQ also plays a vital role for enhancing capacitance of functionalized RGO.

  3. Chemically-induced photoreceptor degeneration and protection in mouse iPSC-derived three-dimensional retinal organoids

    Directory of Open Access Journals (Sweden)

    Shin-ichiro Ito

    2017-10-01

    Full Text Available Induced pluripotent stem cells (iPSCs, which can be differentiated into various tissues and cell types, have been used for clinical research and disease modeling. Self-organizing three-dimensional (3D tissue engineering has been established within the past decade and enables researchers to obtain tissues and cells that almost mimic in vivo development. However, there are no reports of practical experimental procedures that reproduce photoreceptor degeneration. In this study, we induced photoreceptor cell death in mouse iPSC-derived 3D retinal organoids (3D-retinas by 4-hydroxytamoxifen (4-OHT, which induces photoreceptor degeneration in mouse retinal explants, and then established a live-cell imaging system to measure degeneration-related properties. Furthermore, we quantified the protective effects of representative ophthalmic supplements for treating the photoreceptor degeneration. This drug evaluation system enables us to monitor drug effects in photoreceptor cells and could be useful for drug screening.

  4. PRELIMINARY ANALYSIS ON SOME PHYSICO-CHEMICAL RIVERS WATER FEATURES IN PRICOP-HUTA CERTEZE AND TISA SUPERIOARĂ PROTECTED AREAS

    Directory of Open Access Journals (Sweden)

    R. BĂTINAŞ

    2016-03-01

    Full Text Available The present study is focused on the evaluation of river’s water quality from two Natura 2000 protected areas located in Maramureş County, on the northern border between Romania and Ukraine. The field period deployed for the 8 water sampling points was carried out on October 31 – November 1st 2015. Each water sample was analyzed to determinate several features, using a portable multiparameter HI 9828 and a portable turbidimeter HI 98713. Also for geolocation reference has been used a GPS Magellan Explorist 600 device. The investigated parameters were: pH, water temperature and conductivity, total dissolved solids, salinity and water turbidity. The obtained results will be integrated into a more complex study on water quality, regarding the mentioned Natura 200 sites.

  5. Development of an evaluation performance scale for social educators in child protection centers

    Directory of Open Access Journals (Sweden)

    Juan Manuel Fernández Millán

    2013-09-01

    Full Text Available Purpose: In a context of economic crisis, as in the case of Spain, the evaluation of the performance of employees in any field is a key tool for improving worker efficiency. For those professions that are developed in order to provide basic social services to the people of its importance is even greater. Thereby, this study is focused on developing a Performance Rating Scale of Social Workers using BARS technique. Design/methodology/approach: We asked 11 experts to list those competencies they believed necessary to perform this task efficiently. Thereafter, we selected competencies what coincide with an Interjudge arrangement of at least 3. Then each competency was associated with two critical incidents and developed corresponding behavioral anchors. In addition, the scale has a collection of personal data such as age and time off work, often used as indicators defining performance. Finally, the scale was tested to a sample of 128 Social Workers working in interim child care centers and children and youth correctional centers. Findings and Originality/value: The results show that the scale meets the criteria required for validation psychometric (α= 0,873. Also, the scale could be factored (Kaiser-Meyer-Olkin=0,810. Three dimensions were obtained: team work, interpersonal skills and competencies of the work. Research limitations/implications: An appreciation of the lack of covariation between external criteria used as identifiers of good performance (age and number of sick leave and the employee's competence. This confirms the inadequacy of these criteria to predict performance. Necessitating the development of performance evaluation tools that include absenteeism and experience as predictors of performance measures. Practical implications: The inadequacy may be due to the usually confusion between work experience - seniority and sick leave - absenteeism. Originality/value: The study helps define the figure and the competences of social

  6. Hazardous Chemicals

    Centers for Disease Control (CDC) Podcasts

    2007-04-10

    Chemicals are a part of our daily lives, providing many products and modern conveniences. With more than three decades of experience, The Centers for Disease Control and Prevention (CDC) has been in the forefront of efforts to protect and assess people's exposure to environmental and hazardous chemicals. This report provides information about hazardous chemicals and useful tips on how to protect you and your family from harmful exposure.  Created: 4/10/2007 by CDC National Center for Environmental Health.   Date Released: 4/13/2007.

  7. DESIGN AND PERFORMANCE OF A XENOBIOTIC METABOLISM DATABASE MANAGER FOR METABOLIC SIMULATOR ENHANCEMENT AND CHEMICAL RISK ANALYSIS

    Science.gov (United States)

    A major uncertainty that has long been recognized in evaluating chemical toxicity is accounting for metabolic activation of chemicals resulting in increased toxicity. In silico approaches to predict chemical metabolism and to subsequently screen and prioritize chemicals for risk ...

  8. A multimedia exposure assessment methodology for evaluating the performance of the design of structures containing chemical and radioactive wastes

    International Nuclear Information System (INIS)

    Stephanatos, B.N.; Molholt, B.; Walter, K.P.; MacGregor, A.

    1991-01-01

    The objectives of this work are to develop a multimedia exposure assessment methodology for the evaluation of existing and future design of structures containing chemical and radioactive wastes and to identify critical parameters for design optimization. The designs are evaluated in terms of their compliance with various federal and state regulatory requirements. Evaluation of the performance of a particular design is presented within the scope of a given exposure pathway. An exposure pathway has four key components: (1) a source and mechanism of chemical release, (2) a transport medium; (3) a point of exposure; and (4) a route of exposure. The first step in the analysis is the characterization of the waste source behavior. The rate and concentration of releases from the source are evaluated using appropriate mathematical models. The migration of radionuclides and chemicals is simulated through each environmental medium to the exposure point. The total exposure to the potential receptor is calculated, and an estimate of the health effects of the exposure is made. Simulation of the movement of radionuclides and chemical wastes from the source to the receptor point includes several processes. If the predicted human exposure to contaminants meets the performance criteria, the design has been validated. Otherwise the structure design is improved to meet the performance criteria. A phased modeling approach is recommended at a particular mixed waste site. A relatively simple model is initially used to pinpoint critical fate and transport processes and design parameters. The second phase of the modeling effort involves the use of more complex and resource intensive fate and transport models. This final step in the modeling process provides more accurate estimates of contaminant concentrations at the point of exposure. Thus the human dose is more accurately predicted, providing better design validation

  9. Performance of the In Situ Microcosm Technique for Measuring the Degradation of Organic Chemicals in Aquifers

    DEFF Research Database (Denmark)

    Nielsen, Per H.; Christensen, Thomas Højlund; Albrechtsen, Hans-Jørgen

    1996-01-01

    chemicals in polluted and pristine aquifers representing different redox environments. The ISM technique has great potential for providing field-relevant degradation potentials and rate constants, but care must be taken in using the equipment and interpreting the results. This paper provides details......An in situ microcosm (ISM) consists of a stainless steel cylinder isolating about 2 L of the aquifer and is equipped with valves allowing for loading and sampling from the ground surface. During the last five years, this technique has been used frequently to study the degradation of organic...

  10. Performance test of multicomponent quantum mechanical calculation with polarizable continuum model for proton chemical shift.

    Science.gov (United States)

    Kanematsu, Yusuke; Tachikawa, Masanori

    2015-05-21

    Multicomponent quantum mechanical (MC_QM) calculations with polarizable continuum model (PCM) have been tested against liquid (1)H NMR chemical shifts for a test set of 80 molecules. Improvement from conventional quantum mechanical calculations was achieved for MC_QM calculations. The advantage of the multicomponent scheme could be attributed to the geometrical change from the equilibrium geometry by the incorporation of the hydrogen nuclear quantum effect, while that of PCM can be attributed to the change of the electronic structure according to the polarization by solvent effects.

  11. Tuning the performance of a natural treatment process using metagenomics for improved trace organic chemical attenuation

    KAUST Repository

    Drewes, Jorg

    2014-02-01

    By utilizing high-throughput sequencing and metagenomics, this study revealed how the microbial community characteristics including composition, diversity, as well as functional genes in managed aquifer recharge (MAR) systems can be tuned to enhance removal of trace organic chemicals of emerging concern (CECs). Increasing the humic content of the primary substrate resulted in higher microbial diversity. Lower concentrations and a higher humic content of the primary substrate promoted the attenuation of biodegradable CECs in laboratory and field MAR systems. Metagenomic results indicated that the metabolic capabilities of xenobiotic biodegradation were significantly promoted for the microbiome under carbon-starving conditions. © IWA Publishing 2014.

  12. Catalytic Deoxygenation of Renewable Chemicals   – Structure‐Performance Studies

    DEFF Research Database (Denmark)

    Malcho, Phillip

    Generation of chemicals from a viable feedstock is an increasingly interesting field. One of the major issues is the high oxygen ratios in biomass. There are a multitude of ways to remove oxygen from organic molecules. This thesis deals with two topics: The dehydration of glucose into HMF...... to provide a broad platform for the following chapters. Furthermore, the objectives for the thesis are listed here. Chapter 2 deals with the synthetic preparation of the catalysts and the catalytic setups. Chapter 3 deals with the dehydration of glucose into HMF in ionic liquids. The system was investigated...

  13. The effect of cerium-based conversion treatment on the cathodic delamination and corrosion protection performance of carbon steel-fusion-bonded epoxy coating systems

    Energy Technology Data Exchange (ETDEWEB)

    Ramezanzadeh, B., E-mail: ramezanzadeh@aut.ac.ir [Department of Surface Coatings and Corrosion, Institute for Color Science and Technology (ICST), 16765-654, Tehran (Iran, Islamic Republic of); Rostami, M. [Department of Nanomaterials and Nanocoatings, Institute for Color Science and Technology (ICST), 16765-654, Tehran (Iran, Islamic Republic of)

    2017-01-15

    Highlights: • Steel surface was treated by Ce and acid phosphoric solutions. • Ce treatment considerably enhanced the surface energy and produce nanoscale roughness. • Ce treated samples showed enhanced adhesion to FBE coating. • Ce treatment of steel significantly reduced the FBE cathodic delamination rate. • Ce treated sample showed enhanced corrosion resistance. - Abstract: The effect of surface pre-treatment of pipe surface by green cerium compound and phosphoric acid solution on the fusion-bonded epoxy (FBE) coating performance was studied. The composition and surface morphology of the steel samples treated by acid and Ce solutions were characterized by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM), equipped with energy dispersive spectroscopy (EDS). Also, the surface free energy was evaluated on these samples through contact angle measurements. In addition, the effect of Ce and acid washing procedures on the adhesion properties and corrosion protection performance of the FBE was examined by pull-off, salt spray and electrochemical impedance spectroscopy (EIS) tests. Results showed that compared to acid washing, the chemical treatment by Ce solution noticeably increased the surface free energy of steel, improved the adhesion properties of FBE, decreased the cathodic delamination rate of FBE, and enhanced the coating corrosion resistance compared to the acid washed samples.

  14. Synthesis of PLGA nanoparticles of tea polyphenols and their strong in vivo protective effect against chemically induced DNA damage

    Directory of Open Access Journals (Sweden)

    Srivastava AK

    2013-04-01

    Full Text Available Amit Kumar Srivastava,1 Priyanka Bhatnagar,2 Madhulika Singh,1 Sanjay Mishra,1 Pradeep Kumar,2 Yogeshwer Shukla,1 Kailash Chand Gupta1,2 1Proteomics Laboratory, Indian Institute of Toxicology Research (CSIR, Lucknow, India; 2Nucleic Acid Research Laboratory, Institute of Genomics and Integrative Biology (CSIR, Delhi University Campus, India Abstract: In spite of proficient results of several phytochemicals in preclinical settings, the conversion rate from bench to bedside is not very encouraging. Many reasons are attributed to this limited success, including inefficient systemic delivery and bioavailability under in vivo conditions. To achieve improved efficacy, polyphenolic constituents of black (theaflavin [TF] and green (epigallocatechin-3-gallate [EGCG] tea in poly(lactide-co-glycolide nanoparticles (PLGA-NPs were entrapped with entrapment efficacy of ~18% and 26%, respectively. Further, their preventive potential against 7,12-dimethylbenzanthracene (DMBA-induced DNA damage in mouse skin using DNA alkaline unwinding assay was evaluated. Pretreatment (topically of mouse skin with either TF or EGCG (100 µg/mouse doses exhibits protection of 45.34% and 28.32%, respectively, against DMBA-induced DNA damage. However, pretreatment with TF-loaded PLGA-NPs protects against DNA damage 64.41% by 1/20th dose of bulk, 71.79% by 1/10th dose of bulk, and 72.46% by 1/5th dose of bulk. Similarly, 51.28% (1/20th of bulk, 57.63% (1/10th of bulk, and 63.14% (1/5th of bulk prevention was noted using EGCG-loaded PLGA-NP doses. These results showed that tea polyphenol-loaded PLGA-NPs have ~30-fold dose-advantage than bulk TF or EGCG doses. Additionally, TF- or EGCG-loaded PLGA-NPs showed significant potential for induction of DNA repair genes (XRCC1, XRCC3, and ERCC3 and suppression of DNA damage responsive genes (p53, p21, MDM2, GADD45α, and COX-2 as compared with respective bulk TF or EGCG doses. Taken together, TF- or EGCG-loaded PLGA-NPs showed a superior

  15. Chemically doped three-dimensional porous graphene monoliths for high-performance flexible field emitters.

    Science.gov (United States)

    Kim, Ho Young; Jeong, Sooyeon; Jeong, Seung Yol; Baeg, Kang-Jun; Han, Joong Tark; Jeong, Mun Seok; Lee, Geon-Woong; Jeong, Hee Jin

    2015-03-12

    Despite the recent progress in the fabrication of field emitters based on graphene nanosheets, their morphological and electrical properties, which affect their degree of field enhancement as well as the electron tunnelling barrier height, should be controlled to allow for better field-emission properties. Here we report a method that allows the synthesis of graphene-based emitters with a high field-enhancement factor and a low work function. The method involves forming monolithic three-dimensional (3D) graphene structures by freeze-drying of a highly concentrated graphene paste and subsequent work-function engineering by chemical doping. Graphene structures with vertically aligned edges were successfully fabricated by the freeze-drying process. Furthermore, their number density could be controlled by varying the composition of the graphene paste. Al- and Au-doped 3D graphene emitters were fabricated by introducing the corresponding dopant solutions into the graphene sheets. The resulting field-emission characteristics of the resulting emitters are discussed. The synthesized 3D graphene emitters were highly flexible, maintaining their field-emission properties even when bent at large angles. This is attributed to the high crystallinity and emitter density and good chemical stability of the 3D graphene emitters, as well as to the strong interactions between the 3D graphene emitters and the substrate.

  16. Morphology, production, and chemical content performance of black rice Matesih accession with several comparisons

    Science.gov (United States)

    Nandariyah; Purwanto, E.; Meidini, A. N.

    2018-03-01

    Rice (Oryza sativa L.) is an important food crop in Indonesia. In Matesih area, Karanganyar, recently found new varieties of black rice cultured by local farmers which morphology and chemical content have not yet identified. The purpose of this research was to obtain information of morphology, production, and chemical content of black rice matesih accession and to compare the appearance in order to detect the superiority of black rice matesih accession with the comparison of other accession of black rice. There were four accessions of black rice tested, namely Matesih Accession, Klaten Accession, Toraja, and Cempo. Research data were divided into qualitative data which processed by scoring, and quantitative data are processed with simple descriptive statistic. The kinship test was done by using NTSYSpc program with SIMQual and SIMInt function. The observation of qualitative properties indicates that accession matesih has a form that is relatively similar to other accessions. Qualitatively, accession matesih superior at leaf length, leaf width, plant height and culm diameter. Klaten accession has higher production than accession matesih. Matesih accession has the advantage of having shorter period on heading time and harvest time than other accessions. Matesih accession has the highest amylose content, lower protein content than klaten accession and lower content of anthocyanin than toraja accession. The kinship analysis showed that matesih accession and klaten accession has close kinship.

  17. Knowledge, Attitude, and Performance of Secondary School Female Students toward Skin Cancer and Sun Protection Behaviors in Yazd

    Directory of Open Access Journals (Sweden)

    SS Mazloomy Mahmoodabad

    2016-03-01

    Full Text Available Introduction: Skin cancer is regarded as the most common cancer in most countries, whose most important risk factor is exposure to sunlight. Since prevention programs demand to be held in this regard in childhood and adolescence, this study aimed to determine the Knowledge, attitude, and performance of secondary school female students towards skin cancer and sun protection behaviors in Yazd. Methods: This cross-sectional descriptive survey was conducted on 513 secondary school female students, who were selected using a stratified sampling method. The data collection tool was a questionnaire that its reliability was confirmed in Mazloomy's study via Cronbach alpha (0.81. Moreover, the study data were analyzed by descriptive statistics as well as analytic statistics using SPSS software (ver. 11.5. Results: Mean age of participants was 15/88±1/04 years. Mean and standard deviation scores of knowledge, attitude, performance were reported 12.19 ± 5.44 (total core= 37, 18.98 ± 2.26 (total core= 24 and 7.47 ± 2/51 (total core= 16 respectively. Using sunscreen (71.5% was introduced as the most prevalent sun protection behavior. A significant correlation was observed between knowledge and attitude (r= 0.350, p=0.000, as well as performance(r= 0.264, p=0.000 and age (r= 0.134, p=0.010. Conclusion: As the study findings revealed, lack of knowledge as well as undesirable sun protection behaviors except for using sunscreen supported the need to conduct school-based educational intervention.

  18. Performance assessment of commercial relays for anti-islanding protection of rotating machine based distributed generation

    Energy Technology Data Exchange (ETDEWEB)

    Katiraei, F. [Quanta Technology, Houston, TX (United States); Abbey, C. [Natural Resources Canada, Ottawa, ON (Canada). CANMET Energy Technology Centre; Da Cunha, I. [LeapFrog Energy Technologies Inc., Mississauga, ON (Canada); Brisette, Y. [Hydro-Quebec, Montreal, PQ (Canada). Research Inst

    2008-07-01

    According to power industry standards, distributed generation must stop energizing the power grid upon loss of the main system. Either passive or active methods may be used to fulfill this requirement. Passive methods rely on locally measured signals to determine whether the main grid is present, while active methods inject a perturbation into the system that will manifest itself in locally measured signals if the main grid is not present. This paper compared simulation and experimental results for various commercially available relays for passive anti-islanding protection of small (below 500 kW) distributed generators using either synchronous or induction generators. A commercial multifunction relay and an application specific relay for rate-of-change-of-frequency and vector shift were modelled in simulation. Simulation results were compared with tests using a 25 kV induction generator. Results obtained for the induction machine based DG were in good agreement with trip times associated with under/overvoltage relays. The poor results with frequency based relays may be attributed to the method used for calculating frequency. Sensitivity analysis on the degree of capacitor compensation revealed a small non-detection zone, suggesting that this risk should be evaluated for induction machine based interconnections. These results showed that accurate relay modeling is challenging, particularly for frequency based techniques. Other methods for relay testing, such as hardware-in-the-loop, may be more appropriate than simulation, and are more practical in terms of cost effectiveness, than extensive field trials. 7 refs., 1 tab., 6 figs.

  19. Impact of the impurity seeding for divertor protection on the performance of fusion reactors

    Science.gov (United States)

    Siccinio, Mattia; Fable, Emiliano; Angioni, Clemente; Saarelma, Samuli; Scarabosio, Andrea; Zohm, Hartmut

    2017-10-01

    A 0D divertor and scrape-off layer (SOL) model has been coupled to the 1.5D core transport code ASTRA. The resulting numerical tool has been employed for various parameter scans in order to identify the most convenient choices for the operation of electricity producing fusion devices with seeded impurities for the divertor protection. In particular, the repercussions of such radiative species on the main plasma through the fuel dilution have been taken into account. The main result we found is that, when the limits on the maximum tolerable divertor heat flux are enforced, the curves at constant electrical power output are closed on themselves in the R-BT plane, i.e. no improvement would descend from a further increase of R or BT once the maximum has been reached. This occurrence appears as an intrinsic physical limit for all devices where a radiative SOL is needed to deal with the power exhaust. Furthermore, the relative importance of the different power loss channels (e.g. hydrogen radiation, charge exchange, perpendicular transport and impurity radiation), through which the power entering the SOL is dissipated before reaching the target plate, is investigated with our model.

  20. Performance review and reengineering of the protection diodes of the LHC main superconducting magnets

    CERN Document Server

    Savary, F; Bednarek, M J; Dahlerup-Petersen, K; D'Angelo, G; Dib, G; Giloux, C; Grand-Clement, L; Izquierdo Bermudez, S; Moron-Ballester, R; Prin, H; Roger, V; Verweij, A; Willering, G

    2014-01-01

    The LHC main superconducting circuits are composed of up to 154 series-connected dipole magnets and 51 series-connected quadrupole magnets. These magnets operate at 1.9 K in superfluid helium at a nominal current of 11.85 kA. Cold diodes are connected in parallel to each magnet in order to bypass the current in case of a quench in the magnet while ramping down the current in the entire circuit. Both the diodes and the diode leads should therefore be capable of conducting this exponentially decaying current with time constants of up to 100 s. The diode stacks consist of the diodes and their heat sinks, and are essential elements of the protection system from which extremely high reliability is expected. The electrical resistance of 24 diode leads was measured in the LHC machine during operation. Unexpectedly high resistances of the order of 40 μΩ were measured at a few locations, which triggered a comprehensive review of the diode behaviour and of the associated current leads and bolted contacts. In this pap...

  1. The Constitution, waste facility performance standards, and radioactive waste classification: Is equal protection possible?

    Energy Technology Data Exchange (ETDEWEB)

    Eye, R.V. [Kansas Dept. of Health and Environment, Topeka, KS (United States)

    1993-03-01

    The process for disposal of so-called low-level radioactive waste is deadlocked at present. Supporters of the proposed near-surface facilities assert that their designs will meet minimum legal and regulatory standards currently in effect. Among opponents there is an overarching concern that the proposed waste management facilities will not isolate radiation from the biosphere for an adequate length of time. This clash between legal acceptability and a perceived need to protect the environment and public health by requiring more than the law demand sis one of the underlying reasons why the process is deadlocked. Perhaps the most exhaustive public hearing yet conducted on low-level radioactive waste management has recently concluded in Illinois. The Illinois Low-Level Radioactive Waste Disposal Facility Sitting Commission conducted 71 days of fact-finding hearings on the safety and suitability of a site near Martinsville, Illinois, to serve as a location for disposition of low-level radioactive waste. Ultimately, the siting commission rejected the proposed facility site for several reasons. However, almost all the reasons were related, to the prospect that, as currently conceived, the concrete barrier/shallow-land burial method will not isolate radioactive waste from the biosphere. This paper reviews the relevant legal framework of the radioactive waste classification system and will argue that it is inadequate for long-lived radionuclides. Next, the paper will present a case for altering the classification system based on high-level waste regulatory considerations.

  2. International comparisons of health system performance among OECD countries: opportunities and data privacy protection challenges

    NARCIS (Netherlands)

    Oderkirk, Jillian; Ronchi, Elettra; Klazinga, Niek

    2013-01-01

    Health data constitute a significant resource in most OECD countries that could be used to improve health system performance. Well-intended policies to allay concerns about breaches of confidentiality and to reduce potential misuse of personal health information may be limiting data use. A survey of

  3. 29 CFR 1926.1001 - Minimum performance criteria for rollover protective structures for designated scrapers, loaders...

    Science.gov (United States)

    2010-07-01

    ... loaders, and motor graders. The vehicle and ROPS as a system shall have the structural characteristics... direction of the load application, measured at the ROPS top edge. Should the operator's seat be offcenter... Society of Automotive Engineers Recommended Practices: SAE J320a, Minimum Performance Criteria for Roll...

  4. Carbon and graphene double protection strategy to improve the SnOx electrode performance anodes for lithium-ion batteries

    Science.gov (United States)

    Zhu, Jian; Lei, Danni; Zhang, Guanhua; Li, Qiuhong; Lu, Bingan; Wang, Taihong

    2013-05-01

    SnOx is a promising high-capacity anode material for lithium-ion batteries (LIBs), but it usually exhibits poor cycling stability because of its huge volume variation during the lithium uptake and release process. In this paper, SnOx carbon nanofibers (SnOx@CNFs) are firstly obtained in the form of a nonwoven mat by electrospinning followed by calcination in a 0.02 Mpa environment at 500 °C. Then we use a simple mixing method for the synthesis of SnOx@CNF@graphene (SnOx@C@G) nanocomposite. By this technique, the SnOx@CNFs can be homogeneously deposited in graphene nanosheets (GNSs). The highly scattered SnOx@C@G composite exhibits enhanced electrochemical performance as anode material for LIBs. The double protection strategy to improve the electrode performance through producing SnOx@C@G composites is versatile. In addition, the double protection strategy can be extended to the fabrication of various types of composites between metal oxides and graphene nanomaterials, possessing promising applications in catalysis, sensing, supercapacitors and fuel cells.SnOx is a promising high-capacity anode material for lithium-ion batteries (LIBs), but it usually exhibits poor cycling stability because of its huge volume variation during the lithium uptake and release process. In this paper, SnOx carbon nanofibers (SnOx@CNFs) are firstly obtained in the form of a nonwoven mat by electrospinning followed by calcination in a 0.02 Mpa environment at 500 °C. Then we use a simple mixing method for the synthesis of SnOx@CNF@graphene (SnOx@C@G) nanocomposite. By this technique, the SnOx@CNFs can be homogeneously deposited in graphene nanosheets (GNSs). The highly scattered SnOx@C@G composite exhibits enhanced electrochemical performance as anode material for LIBs. The double protection strategy to improve the electrode performance through producing SnOx@C@G composites is versatile. In addition, the double protection strategy can be extended to the fabrication of various types of

  5. Effects of weathering on performance of intumescent coatings for structure fire protection in the wildland-urban interface

    Science.gov (United States)

    Bahrani, Babak

    The objective of this study was to investigate the effects of weathering on the performance of intumescent fire-retardant coatings on wooden products. The weathering effects included primary (solar irradiation, moisture, and temperature) and secondary (environmental contaminants) parameters at various time intervals. Wildland urban interface (WUI) fires have been an increasing threat to lives and properties. Existing solutions to mitigate the damages caused by WUI fires include protecting the structures from ignition and minimizing the fire spread from one structure to another. These solutions can be divided into two general categories: active fire protection systems and passive fire protection systems. Passive systems are either using pre-applied wetting agents (water, gel, or foam) or adding an extra layer (composite wraps or coatings). Fire-retardant coating treatment methods can be divided into impregnated (penetrant) and intumescent categories. Intumescent coatings are easy to apply, economical, and have a better appearance in comparison to other passive fire protection methods, and are the main focus of this study. There have been limited studies conducted on the application of intumescent coatings on wooden structures and their performance after long-term weathering exposure. The main concerns of weathering effects are: 1) the reduction of ignition resistance of the coating layer after weathering; and 2) the fire properties of coatings after weathering since coatings might contribute as a combustible fuel and assist the fire growth after ignition. Three intumescent coatings were selected and exposed to natural weathering conditions in three different time intervals. Two types of tests were performed on the specimens: a combustibility test consisted of a bench-scale performance evaluation using a Cone Calorimeter, and a thermal decomposition test using Simultaneous Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA) method (also known

  6. Evaluation of lightning performance of transmission lines protected by metal oxide surge arresters using artificial intelligence techniques

    Energy Technology Data Exchange (ETDEWEB)

    Christodoulou, C.A.; Perantzakis, G. [Technological Educational Institute (TEI) of Lamia, Department of Electrical Engineering, Lamia (Greece); Spanakis, G.E. [School of Electrical and Computer Engineering, National Technical University of Athens, Athens (Greece); Karampelas, P. [Hellenic American University, Manchester, NH (United States)

    2012-12-15

    Lightning and switching overvoltages are the main causes for faults in electrical networks. In the last decades, several different conventional methodologies have been used for the adjustment of the lightning performance of high voltage transmission lines, which are protected against lightning using overhead ground wires and surge arresters. The current paper proposes a new developed Artificial Neural Network (ANN), based on the Q-learning algorithm, in order to estimate the lightning failure rate of lines of the Hellenic system. The results obtained by the ANN model exhibit a satisfactory correlation in comparison with the real recorded data or the simulations results taken from a conventional method. (orig.)

  7. Chemical exposure reduction: Factors impacting on South African herbicide sprayers' personal protective equipment compliance and high risk work practices.

    Science.gov (United States)

    Andrade-Rivas, Federico; Rother, Hanna-Andrea

    2015-10-01

    The high exposure risks of workers to herbicides in low- and middle-income countries is an important public health concern because of the potential resulting negative impacts on workers' health. This study investigated workers' personal protective equipment (PPE) compliance as a risk mitigation measure; particularly workers who apply herbicides for Working for Water (WfW) - a South African invasive alien vegetation control programme. The study aim was to understand workers' low PPE compliance by analysing their risk perceptions of herbicide use, working conditions and socio-cultural context. Research methods included ethnographic observations, informal interviews, visual media, questionnaires and a focus group. Study results indicated that low PPE compliance persists despite workers' awareness of herbicide exposure risks and as a result of the influence from workers' socio-cultural context (i.e. gender dynamics and social status), herbicide risk perceptions and working conditions (i.e. environmental and logistical). Interestingly, teams comprised of mostly women had the highest compliance rate. These findings highlighted that given the complexity of PPE compliance, especially in countries with several economic and social constraints, exposure reduction interventions should not rely solely on PPE use promotion. Instead, other control strategies requiring less worker input for effectiveness should be implemented, such as elimination and substitution of highly hazardous pesticides, and altering application methods. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  8. Chemical chaperon 4-phenylbutyrate protects against the endoplasmic reticulum stress-mediated renal fibrosis in vivo and in vitro.

    Science.gov (United States)

    Liu, Shing-Hwa; Yang, Ching-Chin; Chan, Ding-Cheng; Wu, Cheng-Tien; Chen, Li-Ping; Huang, Jenq-Wen; Hung, Kuan-Yu; Chiang, Chih-Kang

    2016-04-19

    Renal tubulointerstitial fibrosis is the common and final pathologic change of kidney in end-stage renal disease. Interesting, endoplasmic reticulum (ER) stress is known to contribute to the pathophysiological mechanisms during the development of renal fibrosis. Here, we investigated the effects of chemical chaperon sodium 4-phenylbutyrate (4-PBA) on renal fibrosis in vivo and in vitro. In a rat unilateral ureteral obstruction (UUO) model, 4-PBA mimicked endogenous ER chaperon in the kidneys and significantly reduced glucose regulated protein 78 (GRP78), CCAAT/enhancer binding protein (C/EBP) homologous protein (CHOP), activating transcription factor 4 (ATF4), and phosphorylated JNK protein expressions as well as restored spliced X-box-binding protein 1 (XBP1) expressions in the kidneys of UUO rats. 4-PBA also attenuated the increases of α-smooth muscle actin (α-SMA), connective tissue growth factor (CTGF) protein expressions, tubulointerstitial fibrosis, and apoptosis in the kidneys of UUO rats. Moreover, transforming growth factor (TGF)-β markedly increased ER stress-associated molecules, profibrotic factors, and apoptotic markers in the renal tubular cells (NRK-52E), all of which could be significantly counteracted by 4-PBA treatment. 4-PBA also diminished TGF-β-increased CTGF promoter activity and CTGF mRNA expression in NRK-52E cells. Taken together, our results indicated that 4-PBA acts as an ER chaperone to ameliorate ER stress-induced renal tubular cell apoptosis and renal fibrosis.

  9. Performance evaluation of two protective treatments on salt-laden limestones and marble after natural and artificial weathering.

    Science.gov (United States)

    Salvadori, Barbara; Pinna, Daniela; Porcinai, Simone

    2014-02-01

    Salt crystallization is a major damage factor in stone weathering, and the application of inappropriate protective products may amplify its effects. This research focuses on the evaluation of two protective products' performance (organic polydimethylsiloxane and inorganic ammonium oxalate (NH4)2(COO)2·H2O) in the case of a salt load from behind. Experimental laboratory simulations based on salt crystallization cycles and natural weathering in an urban area were carried out. The effects were monitored over time, applying different methods: weight loss evaluation, colorimetric and water absorption by capillarity measurements, stereomicroscope observations, FTIR and SEM-EDS analyses. The results showed minor impact exerted on the short term on stones, particularly those treated with the water repellent, by atmospheric agents compared to salt crystallization. Lithotypes with low salt load (Gioia marble) underwent minor changes than the heavily salt-laden limestones (Lecce and Ançã stones), which were dramatically damaged when treated with polysiloxane. The results suggest that the ammonium oxalate treatment should be preferred to polysiloxane in the presence of soluble salts, even after desalination procedures which might not completely remove them. In addition, the neo-formed calcium oxalate seemed to effectively protect the stone, improving its resistance against salt crystallization without occluding the pores and limiting the superficial erosion caused by atmospheric agents.

  10. Verification of the correlation between the 210 Pb and the chemical composition of the incrustations found on gas pipelines and the implication on radiological protection

    International Nuclear Information System (INIS)

    Gomes, Franciane Martins de Carvalho

    2004-01-01

    In the last decades, the occurrence of solid residual deposits, known as black powder, in natural-gas pipelines, gathering systems and compression equipment from gas industries has raised increasing regulatory concerns in terms of radiological protection. Concerns are also raised about the waste disposal and management of the radioactive residues eventually produced. Recent projections indicate a significant increase in the production of natural-gas and its products, due to a growing commercial demand, which leads to the production of huge amounts of residues. Thus, more information is needed in order to allow a preliminary evaluation of the radiological profile of this type of industry. In black powder residues, the most prevalent radioisotope is 210 Pb. The present work aimed to investigate the correlation between the chemical composition of the residue and the concentration of 210 Pb, in black powder samples collected at Bacia de Campos, in the State of Rio de Janeiro, Brazil. The main objective was to generate information to regulatory authorities, to the National Commission of Nuclear Energy (CNEN) and to companies that produce natural-gas, such as PETROBRAS. Based on the information, the gas producing companies could elaborate radiological protection guidelines, and also decide about the need for implementation of a waste management program at the installation. The samples of black powder analyzed at the present work have confirmed the existence of such correlation between the concentration of 210 Pb and chemical parameters. In principle, the present results make the use of such correlation feasible for preliminary evaluations of the 210 Pb levels in natural-gas installations. On the other hand, given the geographic limitations, a broader study is recommended, in order to evaluate the investigated correlation, which could be used as a guiding tool for the Brazilian industry of production and processing of natural-gas.(author)

  11. Evaluation of the Financial and Operating Performance of Fertilizers and Chemical & Pharmaceutical Sectors of Indian Public Sector Enterprises After Disinvestment

    Directory of Open Access Journals (Sweden)

    DR. GAGAN SINGH

    2014-04-01

    Full Text Available After 1991 the Government of India is following a policy of economic liberalisation and concept of disinvestment has been more or less accepted by at least all the parties whenever they are Government Disinvestment involves the sale of equity and bond capital invested by the government in PSUs. The failure of the public sector to fulfill the role assigned to it resulted in the protest become louder and more articulate. The main focus of the present paper is to examine the impact of disinvestment on the financial and operating performance of fertilizers and chemical & pharmaceutical sectors of Indian Public sector enterprises. April 2009 onwards, there are fourteen enterprises in which government has undertaken disinvestment recently. After partial disinvestment of both fertilizers and chemical & pharmaceutical sectors of Indian Public sector enterprises, their dependence on the outsiders’ funds has been increased+

  12. Out-of-pile experiments performed in the U.S. Fuel Cladding Chemical Interaction (FCCI) program

    Energy Technology Data Exchange (ETDEWEB)

    Adamson, M G [General Electric Company, Vallecitos Nuclear Center, Pleasanton, CA (United States)

    1977-04-01

    Since 1972 a variety of out-of-pile experiments have been performed as part of the U.S. National Fuel-Cladding Chemical Interaction (FCCI) Program. In the present paper results from these experiments are presented together with descriptions of many of the experimental techniques employed to obtain them. Although the main emphasis of the paper is on experiments designed to characterize FCCI with Type-316-SS cladding, considerable attention is also paid to the following FCCI-related topics: thermodynamics of and phase equilibria in mixed oxide fuel and fission product compounds, fission product and cladding component thermo-transport, and chemical behavior of candidate oxygen-absorber materials (buffer/getters). Detailed interpretations of these results in terms of FCCI mechanisms are presented in a companion paper. (author)

  13. Different stage, different performance: the protective strategy of role play on emotional health in sex work.

    Science.gov (United States)

    Abel, Gillian M

    2011-04-01

    This paper uses Arlie Hochschild's (1983) concept of emotion management and "surface" and "deep acting" to explore how sex workers separate and distance themselves from their public role. Experiences of stigmatisation prevail among sex workers and how stigma is resisted or managed has an impact on their health. In-depth interviews were carried out between August 2006 and April 2007 with 58 sex workers in five cities in New Zealand following decriminalisation of the sex industry. Most participants drew on ideas of professionalism in sustaining a psychological distance between their private and public lives. They utilised "deep acting", transmuting private experiences for use in the work environment, to accredit themselves as professional in their business practices. They also constructed different meanings for sex between public and private relationships with the condom providing an important symbol in separating the two. A few (mostly female street-based) participants were less adept at "deep acting" and relied on drugs to maintain a separation of roles. This paper argues that in an occupation which is highly stigmatised and in which depersonalisation as an aspect of burn-out has been reported as a common occurrence, the ability to draw on strategies which require "deep acting" provides a healthy estrangement between self and role and can be seen as protective. The separation of self from work identity is not damaging as many radical feminists would claim, but an effective strategy to manage emotions. Hochschild, A. (1983). The managed heart: Commercialization of human feeling. Berkeley: University of California Press. Copyright © 2011 Elsevier Ltd. All rights reserved.

  14. Transverse-flow quasi-cw HF chemical laser: design and preliminary performance

    International Nuclear Information System (INIS)

    Gagne, J.M.; Mah, S.Q.; Conturie, Y.

    1974-01-01

    A small transverse-flow HF chemical laser has been constructed using a large volume microwave plasma generator for the production of F atoms. The F atoms react with hydrogen to form the lasing HF molecules. The active medium is about 5 cm long, and the maximum average laser power was found to be 560 mW for all lines. Three laser lines with wavelengths 2.61 μm, 2.64 μm, and 2.73 μm were observed. The time-varying laser transition profile closely resembles the density profile of the excited fluorine atoms in the plasma. Both profiles are greatly affected by changes in flow conditions

  15. Removal of trace organic chemicals and performance of a novel hybrid ultrafiltration-osmotic membrane bioreactor.

    Science.gov (United States)

    Holloway, Ryan W; Regnery, Julia; Nghiem, Long D; Cath, Tzahi Y

    2014-09-16

    A hybrid ultrafiltration-osmotic membrane bioreactor (UFO-MBR) was investigated for over 35 days for nutrient and trace organic chemical (TOrC) removal from municipal wastewater. The UFO-MBR system uses both ultrafiltration (UF) and forward osmosis (FO) membranes in parallel to simultaneously extract clean water from an activated sludge reactor for nonpotable (or environmental discharge) and potable reuse, respectively. In the FO stream, water is drawn by osmosis from activated sludge through an FO membrane into a draw solution (DS), which becomes diluted during the process. A reverse osmosis (RO) system is then used to reconcentrate the diluted DS and produce clean water suitable for direct potable reuse. The UF membrane extracts water, dissolved salts, and some nutrients from the system to prevent their accumulation in the activated sludge of the osmotic MBR. The UF permeate can be used for nonpotable reuse purposes (e.g., irrigation and toilet flushing). Results from UFO-MBR investigation illustrated that the chemical oxygen demand, total nitrogen, and total phosphorus removals were greater than 99%, 82%, and 99%, respectively. Twenty TOrCs were detected in the municipal wastewater that was used as feed to the UFO-MBR system. Among these 20 TOrCs, 15 were removed by the hybrid UFO-MBR system to below the detection limit. High FO membrane rejection was observed for all ionic and nonionic hydrophilic TOrCs and lower rejection was observed for nonionic hydrophobic TOrCs. With the exceptions of bisphenol A and DEET, all TOrCs that were detected in the DS were well rejected by the RO membrane. Overall, the UFO-MBR can operate sustainably and has the potential to be utilized for direct potable reuse applications.

  16. Protection of melanized Cryptococcus neoformans from lethal dose gamma irradiation involves changes in melanin's chemical structure and paramagnetism.

    Directory of Open Access Journals (Sweden)

    Abdelahad Khajo

    Full Text Available Certain fungi thrive in highly radioactive environments including the defunct Chernobyl nuclear reactor. Cryptococcus neoformans (C. neoformans, which uses L-3,4-dihydroxyphenylalanine (L-DOPA to produce melanin, was used here to investigate how gamma radiation under aqueous aerobic conditions affects the properties of melanin, with the aim of gaining insight into its radioprotective role. Exposure of melanized fungal cell in aqueous suspensions to doses of γ-radiation capable of killing 50 to 80% of the cells did not lead to a detectable loss of melanin integrity according to EPR spectra of melanin radicals. Moreover, upon UV-visible (Xe-lamp illumination of melanized cells, the increase in radical population was unchanged after γ-irradiation. Gamma-irradiation of frozen cell suspensions and storage of samples for several days at 77 K however, produced melanin modification noted by a reduced radical population and reduced photoresponse. More direct evidence for structural modification of melanin came from the detection of soluble products with absorbance maxima near 260 nm in supernatants collected after γ-irradiation of cells and cell-free melanin. These products, which include thiobarbituric acid (TBA-reactive aldehydes, were also generated by Fenton reagent treatment of cells and cell-free melanin. In an assay of melanin integrity based on the metal (Bi(+3 binding capacity of cells, no detectable loss in binding was detected after γ-irradiation. Our results show that melanin in C. neoformans cells is susceptible to some damage by hydroxyl radical formed in lethal radioactive aqueous environments and serves a protective role in melanized fungi that involves sacrificial breakdown.

  17. PHYSICAL AND CHEMICAL FUNDAMENTALS OF PROTECTION PROCESSES FOR SURFACE LAYER OF CONCRETE ROAD PAVING BY IMPREGNATING COMPOSITIONS

    Directory of Open Access Journals (Sweden)

    M. K. Pshembayev

    2017-01-01

    Full Text Available Construction of concrete road paving which was started in the 30-ies of the last century in the United States has proved its perspectiveness from the viewpoint of service life. In addition to that an analysis of road usage has shown that concrete paving is a deformation tendency due to some reasons and the tendency entails some difficulties in their repair after rather long operation. The deformations appear more intensively after 5-10-year road operational period. The following negative effects are practically unavoidable: micro-crack formation, scaling, deformation due to freezing of angular edges in concrete plates, destruction of deformation joints etc. The defects are characterized by rather large scope and they are present practically on all the roads. It is necessary to note the fact that a great number of the above-mentioned defects can be avoided on the condition that measures on strengthening surface layer of concrete paving will be undertaken in time. The measures presuppose application of impregnating method while using compositions that contain hydrophobisator and silicon dioxide sol. Industry-produced potassium methyl siliconate, oligomethyl hydride siliconate, tetraethoxysilane have been used as hydrophobisator and they form not easily soluble film on the surface of concrete pores which prevents penetration of water into concrete. Calcium hydrate being formed in the dissolution and hydrolysis process of cement clinker minerals is bound in hydrosilicates which are contained in the solution impregnated by silicon dioxide sol. These hydrosilicates culmatate concrete pores and strengthen its surface layer due to additional hard phase and according to chemical composition it is related to calcium hydrosilicates formed as a result of concrete hardening.

  18. Development and Performance of the Modularized, High-performance Computing and Hybrid-architecture Capable GEOS-Chem Chemical Transport Model

    Science.gov (United States)

    Long, M. S.; Yantosca, R.; Nielsen, J.; Linford, J. C.; Keller, C. A.; Payer Sulprizio, M.; Jacob, D. J.

    2014-12-01

    The GEOS-Chem global chemical transport model (CTM), used by a large atmospheric chemistry research community, has been reengineered to serve as a platform for a range of computational atmospheric chemistry science foci and applications. Development included modularization for coupling to general circulation and Earth system models (ESMs) and the adoption of co-processor capable atmospheric chemistry solvers. This was done using an Earth System Modeling Framework (ESMF) interface that operates independently of GEOS-Chem scientific code to permit seamless transition from the GEOS-Chem stand-alone serial CTM to deployment as a coupled ESM module. In this manner, the continual stream of updates contributed by the CTM user community is automatically available for broader applications, which remain state-of-science and directly referenceable to the latest version of the standard GEOS-Chem CTM. These developments are now available as part of the standard version of the GEOS-Chem CTM. The system has been implemented as an atmospheric chemistry module within the NASA GEOS-5 ESM. The coupled GEOS-5/GEOS-Chem system was tested for weak and strong scalability and performance with a tropospheric oxidant-aerosol simulation. Results confirm that the GEOS-Chem chemical operator scales efficiently for any number of processes. Although inclusion of atmospheric chemistry in ESMs is computationally expensive, the excellent scalability of the chemical operator means that the relative cost goes down with increasing number of processes, making fine-scale resolution simulations possible.

  19. Toddler exposure to flame retardant chemicals: Magnitude, health concern and potential risk- or protective factors of exposure: Observational studies summarized in a systematic review.

    Science.gov (United States)

    Sugeng, Eva J; de Cock, Marijke; Schoonmade, Linda J; van de Bor, Margot

    2017-10-01

    Endocrine disrupting flame retardant (FR) chemicals form a human health concern, that is investigated mostly from the perspective of adult- and early life exposure. No overview of studies on toddler exposure and health effects exist. However, toddlerhood is a critical developmental period and toddlers are at increased risk for exposure because of their age-specific behavior. This systematic review encompasses toddler FR exposure studies in three countries, associated health effects and potential environmental, demographic, or behavioral risk- or protective factors for toddler exposure. A systematic literature search in four databases (PubMed, Embase.com, The Cochrane Library (via Wiley) and Web of Science Core collection) resulted in the identification of ten publications representing seven unique studies that measured brominated and/or phosphorylated FRs in toddlers' (8-24 month-old) serum, urine, hand wipes and feces. This review showed that toddlers are exposed to a range of FRs, that thyroid hormone disruption is associated with FR exposure and that factors in the indoor environment, including products such as plastic toys, might increase FR exposure. Considering the limited amount of studies, and the variety of biological matrices, FRs, and risk- and protective factors, this review did not reveal a uniform pattern of toddler exposure across the different cohorts studied. More evidence is necessary and considering the feasibility of invasive sampling in young children, we suggest to emphasize research on non-invasive matrices. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

  20. Fragrance chemicals lyral and lilial decrease viability of HaCat cells' by increasing free radical production and lowering intracellular ATP level: protection by antioxidants.

    Science.gov (United States)

    Usta, Julnar; Hachem, Yassmine; El-Rifai, Omar; Bou-Moughlabey, Yolla; Echtay, Karim; Griffiths, David; Nakkash-Chmaisse, Hania; Makki, Rajaa Fakhoury

    2013-02-01

    We investigate in this study the biochemical effects on cells in culture of two commonly used fragrance chemicals: lyral and lilial. Whereas both chemicals exerted a significant effect on primary keratinocyte(s), HaCat cells, no effect was obtained with any of HepG2, Hek293, Caco2, NIH3T3, and MCF7 cells. Lyral and lilial: (a) decreased the viability of HaCat cells with a 50% cell death at 100 and 60 nM respectively; (b) decreased significantly in a dose dependant manner the intracellular ATP level following 12-h of treatment; (c) inhibited complexes I and II of electron transport chain in liver sub-mitochondrial particles; and (d) increased reactive oxygen species generation that was reversed by N-acetyl cysteine and trolox and the natural antioxidant lipoic acid, without influencing the level of free and/or oxidized glutathione. Lipoic acid protected HaCat cells against the decrease in viability induced by either compound. Dehydrogenation of lyral and lilial produce α,β-unsaturated aldehydes, that reacts with lipoic acid requiring proteins resulting in their inhibition. We propose lyral and lilial as toxic to mitochondria that have a direct effect on electron transport chain, increase ROS production, derange mitochondrial membrane potential, and decrease cellular ATP level, leading thus to cell death. Copyright © 2012 Elsevier Ltd. All rights reserved.

  1. Is the aquatic environment sufficiently protected from chemicals discharged with treated ballast water from vessels worldwide? - A decadal environmental perspective and risk assessment.

    Science.gov (United States)

    David, Matej; Linders, Jan; Gollasch, Stephan; David, Jan

    2018-05-24

    Ballast water managements systems (BWMS) installed on vessels may use active substances to inactivate or kill organisms in the ballast water. This paper provides new insights in this global issue - discharge of hazardous disinfection by-products with ballast water and related risk assessment for the environment. Considering the possible extent of this issue, the International Maritime Organization (IMO) engaged the Joint Group of Experts on the Scientific Aspects of Marine Environmental Protection (GESAMP)-Ballast Water Working Group (BWWG) to oversee the evaluation process of BWMS that make use of active substances to prevent negative effects. We analysed all BWMS that received IMO final approval over a decade until 2017 and provide an overview of active substances used for ballast water treatment and disinfection by-products in the discharged ballast water. A risk assessment was conducted using the GESAMP-BWWG methodology for two very different commercial ports (Koper, Slovenia and Hamburg, Germany). Some relevant chemicals (chloropicrin, monochloroacetic acid, and dibromoacetonitrile) and other chemicals (isocyanuric acid and sodium thiosulphate) reached levels of concern, indicating a risk for aquatic organisms after discharge of that ballast water. From this analysis, it became clear GESAMP-BWWG worst-case scenario assumptions do not fully account for the potential environmental risks. We provide recommendations how to make this risk assessment more robust, recommend further research, and urge for policy as well as regulatory responses. Copyright © 2018 Elsevier Ltd. All rights reserved.

  2. Chemical Function Predictions for Tox21 Chemicals

    Data.gov (United States)

    U.S. Environmental Protection Agency — Random forest chemical function predictions for Tox21 chemicals in personal care products uses and "other" uses. This dataset is associated with the following...

  3. Performance of calcium manganate as oxygen carrier in chemical looping combustion of biochar in a 10 kW pilot

    International Nuclear Information System (INIS)

    Schmitz, Matthias; Linderholm, Carl Johan

    2016-01-01

    Highlights: • A manganese-based perovskite material was used as oxygen carrier in chemical looping combustion. • The oxygen carrier’s performance was superior to materials previously tested in this reactor throughout the testing period. • Under stable conditions, oxygen demand was as low as 2.1% with a carbon capture efficiency of up to 98%. • No signs of agglomeration were detected. • Gaseous oxygen was released at all relevant fuel reactor temperatures. - Abstract: Chemical looping combustion (CLC) and chemical looping with oxygen uncoupling (CLOU) are carbon capture technologies which achieve gas separation by means of cycling oxidation and reduction of a solid oxygen carrier. In this study, the performance and CLOU properties of an oxygen carrier with perovskite structure, CaMn_0_._9Mg_0_._1O_3_−_δ_, were investigated in a 10 kW pilot. The fuel consisted of biochar with very low sulphur content. Around 37 h of operation with fuel were carried out in the 10 kW chemical looping combustor. Previous operational experience in this unit has been achieved using different natural minerals as oxygen carrier – mainly ilmenite and manganese ore. Parametric studies performed in this work included variation of fuel flow, solids circulation rate, temperature and fluidization gas in the fuel reactor. The oxygen carrier was exposed to a total 73 h of hot fluidization (T > 600 °C). No hard particle agglomerations were formed during the experiments. An oxygen demand as low as 2.1% could be reached under stable operating conditions, with a carbon capture efficiency of up to 98%. CLOU properties were observed at all fuel reactor temperatures, ensuring stable operation even without steam as gasification agent present in the fuel reactor. The results suggest that CaMn_0_._9Mg_0_._1O_3_−_δ is suitable for the use as oxygen carrier in chemical looping combustion of solid biochar and offers higher gas conversion than previously tested materials without CLOU

  4. Effects of rumen-protected choline supplementation on metabolic and performance responses of transition dairy cows.

    Science.gov (United States)

    Leiva, T; Cooke, R F; Brandão, A P; Marques, R S; Vasconcelos, J L M

    2015-04-01

    The objective of this experiment was to compare metabolic and milk production parameters in dairy cows supplemented and nonsupplemented with rumen-protected choline (RPC) during the transition period. Twenty-three nonlactating, multiparous, pregnant Holstein cows were ranked by BW and BCS 21 d before expected date of calving and immediately were assigned to receive (n = 12) or not receive (control; n = 11) RPC until 45 d in milk (DIM). Cows supplemented with RPC received (as-fed basis) 50 and 100 g/d of RPC (18.8% choline) before and after calving, respectively. Before calving, cows were maintained in 2 drylot pens according to treatment with ad libitum access to corn silage, and individually they received (as-fed basis) 3 kg/cow daily of a concentrate. Upon calving, cows were moved to 2 adjacent drylot pens according to treatment, milked twice daily, offered (as-fed basis) 35 kg/cow daily of corn silage, and individually received a concentrate formulated to meet their nutritional requirements after milking. The RPC was individually offered to cows as a topdressing into the morning concentrate feeding. Before calving, cow BW and BCS were recorded weekly, and blood samples were collected every 5 d beginning on d -21 relative to expected calving date. Upon calving and until 45 DIM, BW and BCS were recorded weekly, individual milk production was recorded daily, and milk samples were collected once a week and analyzed for fat, protein, and total solids. Blood samples were collected every other day from 0 to 20 DIM and every 5 d from 20 to 45 DIM. Based on actual calving dates, cows receiving RPC or control began receiving treatments 16.8 ± 1.7 and 17.3 ± 2.0 d before calving, respectively. No treatment effects were detected (P ≥ 0.18) on postpartum concentrate intake, BW and BCS, or serum concentrations of cortisol, β-hydroxybutyrate, NEFA, glucose, and IGF-I. Cows supplemented with RPC had greater (P ≤ 0.01) mean serum haptoglobin and insulin concentrations

  5. Effect of chemically converted graphene as an electrode interfacial modifier on device-performances of inverted organic photovoltaic cells

    Science.gov (United States)

    Kang, Tae-Woon; Noh, Yong-Jin; Yun, Jin-Mun; Yang, Si-Young; Yang, Yong-Eon; Lee, Hae-Seong; Na, Seok-In

    2015-06-01

    This study examined the effects of chemically converted graphene (CCG) materials as a metal electrode interfacial modifier on device-performances of inverted organic photovoltaic cells (OPVs). As CCG materials for interfacial layers, a conventional graphene oxide (GO) and reduced graphene oxide (rGO) were prepared, and their functions on OPV-performances were compared. The inverted OPVs with CCG materials showed all improved cell-efficiencies compared with the OPVs with no metal/bulk-heterojunction (BHJ) interlayers. In particular, the inverted OPVs with reduction form of GO showed better device-performances than those with GO and better device-stability than poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)-based inverted solar cells, showing that the rGO can be more desirable as a metal/BHJ interfacial material for fabricating inverted-configuration OPVs.

  6. The use of chitooligosaccharide in beer brewing for protection against beer-spoilage bacteria and its influence on beer performance.

    Science.gov (United States)

    Zhao, Xue; Yu, Zhimin; Wang, Ting; Guo, Xuan; Luan, Jing; Sun, Yumei; Li, Xianzhen

    2016-04-01

    To identify a biological preservative that can protect beer from microbial contamination, which often results in the production of turbidity and off-flavor. The antimicrobial activity of a chitooligosaccharide against beer-spoilage bacteria and its effect on the fermentation performance of brewer's yeast was studied. Chitooligosaccharide with an average 2 kDa molecular weight was the best at inhibiting all tested beer-spoilage bacteria. The application of chitooligosaccharide in the brewing process did not influence the fermentation of brewer's yeast. The change in beer performance induced by the contamination of Lactobacillus brevis could be effectively controlled by application of chitooligosaccharide in the beer brewing process. The experimental data suggested that chitooligosaccharide should be an excellent preservative to inhibit beer-spoilage bacteria in the brewing process and in the end product.

  7. Performance, compliance and reliability of Waste stabilization pond: Effluent discharge quality and environmental protection agency standards in Ghana

    DEFF Research Database (Denmark)

    Owusu-Ansah, Emmanuel de-Graft Johnson; Sampson, Angelina; Amponsah, Samuel K.

    2015-01-01

    function to establish the relationship between the statistical coefficient of variation and the coefficient of reliability based on rth moment about the origin in the moment of generation function to generate the functions of the mean and standard deviation, properties of the standard Z normal distribution...... were used to establish the coefficient of reliability relationship depending on the coefficient of variation influenced by the standard of deviation. Discharge values of Physico-chemical Parameters measured from the WSP were found be performing acceptably based on the EPA standards, whereas only four......Measuring performance has been arguerably, one of the metric with many facets with different school of thoughts, as there exist different approaches of measuring it. Several of the existing approaches measure such metric by comparison with standards esherined in policy documents and as a result...

  8. Performance of sand and shredded rubber tire mixture as a natural base isolator for earthquake protection

    Science.gov (United States)

    Bandyopadhyay, Srijit; Sengupta, Aniruddha; Reddy, G. R.

    2015-12-01

    The performance of a well-designed layer of sand, and composites like layer of sand mixed with shredded rubber tire (RSM) as low cost base isolators, is studied in shake table tests in the laboratory. The building foundation is modeled by a 200 mm by 200 mm and 40 mm thick rigid plexi-glass block. The block is placed in the middle of a 1m by 1m tank filled with sand. The selected base isolator is placed between the block and the sand foundation. Accelerometers are placed on top of the footing and foundation sand layer. The displacement of the footing is also measured by LVDT. The whole setup is mounted on a shake table and subjected to sinusoidal motions with varying amplitude and frequency. Sand is found to be effective only at very high amplitude (> 0.65 g) of motions. The performance of a composite consisting of sand and 50% shredded rubber tire placed under the footing is found to be most promising as a low-cost effective base isolator.

  9. Adequate performance of cardiopulmonary resuscitation techniques during simulated cardiac arrest over and under protective equipment in football.

    Science.gov (United States)

    Waninger, Kevin N; Goodbred, Andrew; Vanic, Keith; Hauth, John; Onia, Joshua; Stoltzfus, Jill; Melanson, Scott

    2014-07-01

    To investigate (1) cardiopulmonary resuscitation (CPR) adequacy during simulated cardiac arrest of equipped football players and (2) whether protective football equipment impedes CPR performance measures. Exploratory crossover study performed on Laerdal SimMan 3 G interactive manikin simulator. Temple University/St Luke's University Health Network Regional Medical School Simulation Laboratory. Thirty BCLS-certified ATCs and 6 ACLS-certified emergency department technicians. Subjects were given standardized rescuer scenarios to perform three 2-minute sequences of compression-only CPR. Baseline CPR sequences were captured on each subject. Experimental conditions included 2-minute sequences of CPR either over protective football shoulder pads or under unlaced pads. Subjects were instructed to adhere to 2010 American Heart Association guidelines (initiation of compressions alone at 100/min to 51 mm). Dependent variables included average compression depth, average compression rate, percentage of time chest wall recoiled, and percentage of hands-on contact during compressions. Differences between subject groups were not found to be statistically significant, so groups were combined (n = 36) for analysis of CPR compression adequacy. Compression depth was deeper under shoulder pads than over (P = 0.02), with mean depths of 36.50 and 31.50 mm, respectively. No significant difference was found with compression rate or chest wall recoil. Chest compression depth is significantly decreased when performed over shoulder pads, while there is no apparent effect on rate or chest wall recoil. Although the clinical outcomes from our observed 15% difference in compression depth are uncertain, chest compression under the pads significantly increases the depth of compressions and more closely approaches American Heart Association guidelines for chest compression depth in cardiac arrest.

  10. Down-Regulation of Homer1b/c Protects Against Chemically Induced Seizures Through Inhibition of mTOR Signaling

    Directory of Open Access Journals (Sweden)

    Lei Cao

    2015-03-01

    Full Text Available Background: Homer is a family of post synaptic density proteins functionally and physically attached to target proteins at proline-rich sequences. Reducing Homer1b/c expression has been shown in previous studies to be protective against excitotoxic insults, implicating Homer1b/c in the physiological regulation of aberrant neuronal excitability. Methods: To test the efficacy of a Homer1b/c reducing therapy for disorders with a detrimental hyperexcitability profile in mice, we used small interfere RNA (siRNA to decrease endogenous Homer1b/c expression in mouse hippocampus. The baseline motor and cognitive behavior was measured by sensorimotor tests, Morris water maze and elevated plus maze tasks. The anti-epileptic effects of Homer1b/c knockdown were determined in two chemically induced seizure models induced by Picrotoxin (PTX or pentylenetetrazole (PTZ administration. Results: The results of sensorimotor tests, Morris water maze and elevated plus maze tasks showed that Homer1b/c reduction had no effect on baseline motor or cognitive behavior. In two chemically induced seizure models, mice with reduced Homerb/c protein had less severe seizures than control mice. Total Homer1b/c protein levels and seizure severity were highly correlated, such that those mice with the most severe seizures also had the highest levels of Homer1b/c. In addition, the phosphorylation of mammalian target of rapamycin (mTOR and its target protein S6 was significantly inhibited in Homer1b/c down-regulated mice. Homer1b/c knockdown-induced inhibition of mTOR pathway was partially ablated by the metabotropic glutamate receptor 5 (mGluR5 agonist CHPG. Conclusion: Our results demonstrate that endogenous Homer1b/c is integral for regulating neuronal hyperexcitability in adult animals and suggest that reduction of Homer1b/c could protect against chemically induced seizures through inhibition mTOR pathway.

  11. Renewable High-Performance Fibers from the Chemical Recycling of Cotton Waste Utilizing an Ionic Liquid.

    Science.gov (United States)

    Asaadi, Shirin; Hummel, Michael; Hellsten, Sanna; Härkäsalmi, Tiina; Ma, Yibo; Michud, Anne; Sixta, Herbert

    2016-11-23

    A new chemical recycling method for waste cotton is presented that allows the production of virgin textile fibers of substantially higher quality than that from the mechanical recycling methods that are used currently. Cotton postconsumer textile wastes were solubilized fully in the cellulose-dissolving ionic liquid 1,5-diazabicyclo[4.3.0]non-5-enium acetate ([DBNH]OAc) to be processed into continuous filaments. As a result of the heterogeneous raw material that had a different molar mass distribution and degree of polymerization, pretreatment to adjust the cellulose degree of polymerization by acid hydrolysis, enzyme hydrolysis, or blending the waste cotton with birch prehydrolyzed kraft pulp was necessary to ensure spinnability. The physical properties of the spun fibers and the effect of the processing parameters on the ultrastructural changes of the fibers were measured. Fibers with a tenacity (tensile strength) of up to 58 cN tex -1 (870 MPa) were prepared, which exceeds that of native cotton and commercial man-made cellulosic fibers. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. The effects of chemical kinetics and wall temperature on performance of porous media burners

    Science.gov (United States)

    mohammadi, Iman; Hossainpour, Siamak

    2013-06-01

    This paper reports a two-dimensional numerical prediction of premixed methane-air combustion in inert porous media burner by using of four multi-step mechanisms: GRI-3.0 mechanism, GRI-2.11 mechanism and the skeletal and 17 Species mechanisms. The effects of these models on temperature, chemical species and pollutant emissions are studied. A two-dimensional axisymmetric model for premixed methane-air combustion in porous media burner has developed. The finite volume method has used to solve the governing equations of methane-air combustion in inert porous media burner. The results indicate that the present four models have the same accuracy in predicting temperature profiles and the difference between these profiles is not more than 2 %. In addition, the Gri-3.0 mechanism shows the best prediction of NO emission in comparison with experimental data. The 17 Species mechanism shows good agreement in prediction of temperature and pollutant emissions with GRI-3.0, GRI-2.11 and the skeletal mechanisms. Also the effects of wall temperature on the gas temperature and mass fraction of species such as NO and CH4 are studied.

  13. International conference on the performance of engineered barriers. Physical and chemical properties, behaviour and evolution. Short abstracts

    Energy Technology Data Exchange (ETDEWEB)

    Schaefers, Annika; Fahland, Sandra (eds.)

    2014-08-01

    The volume includes the abstracts of the papers presented at the international conference on the performance of engineered barrier systems, their physical and chemical properties, behavior and evolution. The papers cover the topics bentonite buffers, radioactive waste repository safety, geophysical and geochemical property monitoring, repository sealing materials, thermo-hydro-mechanical characterization, gas injection tests, hydration and heating tests, clay-iron interaction experiments, water retention behavior, thermal stability of materials, numerical modeling studies, long-term simulations, thermo-hydrologic phenomena, uncertainty and sensitivity studies, probabilistic assessments, preliminary safety analyses of Gorleben.

  14. Performance Assessment of Hazardous Air Pollutant (HAP)Free Chemical Paint Strippers on Military Coatings for Validation to Federal Specification TT-R-2918A

    Science.gov (United States)

    2016-03-01

    ARL-TN-0742 ● MAR 2016 US Army Research Laboratory Performance Assessment of Hazardous Air Pollutant (HAP)–Free Chemical Paint...the originator. ARL-TN-0742 ● MAR 2016 US Army Research Laboratory Performance Assessment of Hazardous Air Pollutant (HAP...COVERED (From - To) 1–30 April 2014 4. TITLE AND SUBTITLE Performance Assessment of Hazardous Air Pollutant (HAP)–Free Chemical Paint Strippers

  15. Simultaneous determination of some ultraviolet-absorbing chemicals in sunscreen cosmetics using a high-performance liquid chromatography method.

    Science.gov (United States)

    Liu, T; Wu, D

    2011-10-01

    A method of gradient elution high-performance liquid chromatography (HPLC) for simultaneous determination of 11 different ultraviolet-absorbing chemicals of phenylbenzlmldazole sulphonic acid, 4-aminobenzoic acid, benzophenone-4, benzophenone-3, isoamyl p-methoxycinnamate, 4-methylbenzylidene camphor, octocrylene, ethylhexyl methoxycinnamate, homosalate, ethylhexyl salicylate, methylene bis-benzotriazolyl tetramethylbutyl phenol was developed for the application to sunscreen cosmetic products. In this study, an Agilent SB-C18 analytical column (250 × 4.6 mm, 5 μm) was utilized and methanol, tetrahydrofuran and perchloric acid aqueous solution (0.2 mL HClO(4) + 300 mL H(2)O) were used for gradient elution at a total flow rate of 1.0 mL min(-1). The optimum conditions for 11 different ultraviolet-absorbing chemicals analyses were investigated. All calibration curves showed good linear regression with UV detection (311 nm) within test ranges. The correlation coefficients were better than 0.999 in all cases. The assay was simple, selective, convenient and reproducible and is suitable for the determination of ultraviolet-absorbing chemicals in commercial sunscreen cosmetic products. The use frequency of 11 different ultraviolet absorbents in 100 sunscreen cosmetics was investigated and statistically analysed. The ultraviolet absorbent of maximum use frequency was ethylhexyl methoxycinnamate. © 2011 The Authors. ICS © 2011 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  16. Chemical Welding on Semimetallic TiS2 Nanosheets for High-Performance Flexible n-Type Thermoelectric Films.

    Science.gov (United States)

    Zhou, Yuan; Wan, Juanyong; Li, Qi; Chen, Lei; Zhou, Jiyang; Wang, Heao; He, Dunren; Li, Xiaorui; Yang, Yaocheng; Huang, Huihui

    2017-12-13

    Solution-based processing of two-dimensional (2D) materials provides the possibility of allowing these materials to be incorporated into large-area thin films, which can translate the interesting fundamental properties of 2D materials into available devices. Here, we report for the first time a novel chemical-welding method to achieve high-performance flexible n-type thermoelectric films using 2D semimetallic TiS 2 nanosheets. We employ chemically exfoliated TiS 2 nanosheets bridged with multivalent cationic metal Al 3+ to cross-link the nearby sheets during the film deposition process. We find that such a treatment can greatly enhance the stability of the film and can improve the power factor by simultaneously increasing the Seebeck coefficient and electrical conductivity. The resulting TiS 2 nanosheet-based flexible film shows a room temperature power factor of ∼216.7 μW m -1 K -2 , which is among the highest chemically exfoliated 2D transition-metal dichalcogenide nanosheet-based films and comparable to the best flexible n-type thermoelectric films, to our knowledge, indicating its potential applications in wearable electronics.

  17. Protecting Contract Workers: Case Study of the US Department of Energy’s Nuclear and Chemical Waste Management

    Science.gov (United States)

    Gochfeld, Michael; Mohr, Sandra

    2007-01-01

    Increased reliance on subcontractors in all economic sectors is a serious occupational health and safety challenge. Short-term cost savings are offset by long-term liability. Hiring subcontractors brings specialized knowledge but also young, inexperienced, inadequately trained workers onto industrial and hazardous waste sites, which leads to increased rates of accidents and injuries. Reliable data on subcontractor occupational health and safety programs and performance are sparse. The US Department of Energy has an excellent safety culture on paper, but procurement practices and contract language deliver a mixed message—including some safety disincentives. Its biphasic safety outcome data are consistent with underreporting by some subcontractors and underachievement by others. These observations are relevant to the private and public sectors. Occupational health and safety should be viewed as an asset, not merely a cost. PMID:17666686

  18. The Study of Implement of HCS Program at Hazardous Chemicals Knowledge and Safety performance in Tehran refinery, s laboratory unit

    Directory of Open Access Journals (Sweden)

    N. Hassanzadeh-Rangi

    2008-10-01

    Full Text Available Background and aims   The HCS standard includes listing of chemicals, labeling of chemical  containers, preparation of material safety data sheets, writing plan and employee training  programs. The aim of this study was to determine the influence of implemented program to enhance the knowledge and safety performance level of employees.   Methods   The knowledge level and unsafe act ratio were measured using both questionnaire  and behavior checklist (with safety sampling method before and after enforcing this interface.   Results   In this study, the mean and standard deviation of the knowledge level of employees  related to chemical safety before enforcing the interface was 46% and 14%. However, after  enforcing the interface, mean and standard deviation was 88% and 12%. The paired-t-test result   in this parameter was significant (p-value <0.0001. The mean and standard deviation of  knowledge level of employees related to warning labels before to enforcing the interface was 29%  and 22%. After enforcing the interface, mean and standard deviation was 80% and 16%. The paired-t-test result in this parameter was significant (p-value <0.0001. The mean and standard  deviation of the knowledge level of employees related to hazard communication methods before enforcing the interface was 25% and 11%. After enforcing the interface, mean and standard deviation was 79% and 16%. The paired-t-test result in this parameter was significant (p-value   <0.001.   Conclusion   The obtained result revealed that enhancement of the knowledge related to chemical safety, hazard communication methods and warning labels was significant. Statistical paired-t-test and control chart methods was used to comparison between unsafe act ratio before  and after enforcing the interface. The mean and standard deviation of unsafe act ratio before implementation of HCS program was 23.6% and 5.49%. However, mean and standard deviation of unsafe act ratio

  19. Comparison the performance of different catalysts in chemical modification of Poplar wood with Glutaraldehyde

    Directory of Open Access Journals (Sweden)

    ندا اسماعیلی

    2016-12-01

    Full Text Available In this study, the effect of different catalysts on chemical modification of poplar wood and physical properties of the resulting product was evaluated. 12.5% HCl and water soluble salts containing ZnCl2, CaCl2, AlCl3, MgCl2 (based on the weight of glutaraldehyde and 1% Al2O3, SiO2 and ZnO nano particles (based on the weight of glutaraldehyde were used. After heating in oven for 48 hour, modification with glutaraldehyde and MgCl2, ZnO nano particles, SiO2, Al2O3, ZnCl2, AlCl3, CaCl2 and HCl as catalysts were resulted to 14.5, 12.57, 10.62, 8.69, 8.51, 7.19, 5.97 and 5.41 % weight gain respectively. After 24h soaking in water, the physical properties of modified specimens, such as water absorption, volume swelling and ASE were measured. The highest and lowest bulking were calculated for Mgcl2 and Hcl catalysts with 6.98 and 2.37% respectively. The modification in presence of Mgcl2 catalyst was shown highest increase of density with average of 0.55 g/cm3. The highest and lowest water absorption was measured 79.61 and 45.32% in the modification with HCl and MgCl catalysts. Hcl with acidic quality, can break ether bonds in hemiacetal and even acetal structure. Modification with MgCl2 was shown best result in comparison with other catalysts. It is likely that the formation a complex of magnesium with oxygen, could resulted to activate carbonyl groups in glutaraldehyde and created the crosslink.

  20. Chemical and physical parameters affecting the performance of the Os-191/Ir-191m generator

    International Nuclear Information System (INIS)

    Packard, A.B.; Butler, T.A.; Knapp, F.F.; O'Brien, G.M.; Treves, S.

    1984-01-01

    The development of an Os-191/Ir-191m generator suitable for radionuclide angiography in humans has elicited much interest. This generator employs ''(OsO 2 Cl 4 ) 2- '' on AG MP-1 anion exchange resin with a Dowex-2 scavenger column and is eluted with normal saline at pH 1. The parent Os species is, however, neither welldefined nor homogeneous leading to less than optimal breakthrough of Os-191 (5 x 10 -3 %) and modest Ir-191m yield (10-15%). The effect of a range of parameters on generator performance has been evaluated as has been the way in which the assembly and loading process affects generator performance. In addition, a number of potential alternative generator systems have been evaluated